SORBENTS FOR FLUORIDE, METAL FINISHING, AND PETROLEUM SLUDGE LEACHATE CONTAMINANT CONTROL

EPA Science Inventory

This report covers the initial laboratory studies carried out to identify the most promising sorbents that may be used to significantly reduce the concentration of measurable contaminant in calcium fluoride sludge leachate, metal finishing sludge leachate, and petroleum sludge le...

Demonstration of acid and water recovery systems: Applicability and operational challenges in Indian metal finishing SMEs.

PubMed

Balakrishnan, M; Batra, R; Batra, V S; Chandramouli, G; Choudhury, D; Hälbig, T; Ivashechkin, P; Jain, J; Mandava, K; Mense, N; Nehra, V; Rögener, F; Sartor, M; Singh, V; Srinivasan, M R; Tewari, P K

2018-07-01

Diffusion dialysis, acid retardation and nanofiltration plants were acquired from Europe and demonstrated in several Indian metal finishing companies over a three year period. These companies are primarily small and medium enterprises (SMEs). Free acid recovery rate from spent pickling baths using diffusion dialysis and retardation was in the range of 78-86% and 30-70% respectively. With nanofiltration, 80% recovery rate of rinse water was obtained. The demonstrations created awareness among the metal finishing companies to reuse resources (acid/water) from the effluent streams. However, lack of efficient oil separators, reliable chemical analysis and trained personnel as well as high investment cost limit the application of these technologies. Local manufacturing, plant customization and centralized treatment are likely to encourage the uptake of such technologies in the Indian metal finishing sector. Copyright © 2018 Elsevier Ltd. All rights reserved.

Solder flow over fine line PWB surface finishes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hosking, F.M.; Hernandez, C.L.

1998-08-01

The rapid advancement of interconnect technology has stimulated the development of alternative printed wiring board (PWB) surface finishes to enhance the solderability of standard copper and solder-coated surfaces. These new finishes are based on either metallic or organic chemistries. As part of an ongoing solderability study, Sandia National Laboratories has investigated the solder flow behavior of two azole-based organic solderability preservations, immersion Au, immersion Ag, electroless Pd, and electroless Pd/Ni on fine line copper features. The coated substrates were solder tested in the as-fabricated and environmentally-stressed conditions. Samples were processed through an inerted reflow machine. The azole-based coatings generally providedmore » the most effective protection after aging. Thin Pd over Cu yielded the best wetting results of the metallic coatings, with complete dissolution of the Pd overcoat and wetting of the underlying Cu by the flowing solder. Limited wetting was measured on the thicker Pd and Pd over Ni finishes, which were not completely dissolved by the molten solder. The immersion Au and Ag finishes yielded the lowest wetted lengths, respectively. These general differences in solderability were directly attributed to the type of surface finish which the solder came in contact with. The effects of circuit geometry, surface finish, stressing, and solder processing conditions are discussed.« less

FINAL REPORT FOR VERIFICATION OF THE METAL FINISHING FACILITY POLLUTION PREVENTION TOOL (MFFPPT)

EPA Science Inventory

The United States Environmental Protection Agency (USEPA) has prepared a computer process simulation package for the metal finishing industry that enables users to predict process outputs based upon process inputs and other operating conditions. This report documents the developm...

Fabrication of high precision metallic freeform mirrors with magnetorheological finishing (MRF)

NASA Astrophysics Data System (ADS)

Beier, Matthias; Scheiding, Sebastian; Gebhardt, Andreas; Loose, Roman; Risse, Stefan; Eberhardt, Ramona; Tünnermann, Andreas

2013-09-01

The fabrication of complex shaped metal mirrors for optical imaging is a classical application area of diamond machining techniques. Aspherical and freeform shaped optical components up to several 100 mm in diameter can be manufactured with high precision in an acceptable amount of time. However, applications are naturally limited to the infrared spectral region due to scatter losses for shorter wavelengths as a result of the remaining periodic diamond turning structure. Achieving diffraction limited performance in the visible spectrum demands for the application of additional polishing steps. Magnetorheological Finishing (MRF) is a powerful tool to improve figure and finish of complex shaped optics at the same time in a single processing step. The application of MRF as a figuring tool for precise metal mirrors is a nontrivial task since the technology was primarily developed for figuring and finishing a variety of other optical materials, such as glasses or glass ceramics. In the presented work, MRF is used as a figuring tool for diamond turned aluminum lightweight mirrors with electroless nickel plating. It is applied as a direct follow-up process after diamond machining of the mirrors. A high precision measurement setup, composed of an interferometer and an advanced Computer Generated Hologram with additional alignment features, allows for precise metrology of the freeform shaped optics in short measuring cycles. Shape deviations less than 150 nm PV / 20 nm rms are achieved reliably for freeform mirrors with apertures of more than 300 mm. Characterization of removable and induced spatial frequencies is carried out by investigating the Power Spectral Density.

SUMMARY REPORT: CONTROL AND TREATMENT TECHNOLOGY FOR THE METAL FINISHING INDUSTRY: IN -PLANT CHANGES

EPA Science Inventory

This 30 - page Technology Transfer Report ummarizes how he metal finishing industry in the United States is subject to a variety of changing business conditions. wo of the most significant factors are the increasing costs of materials, such as plating chemicals and process water,...

THE USEPA'S METAL FINISHING FACILITY RISK SCREENING TOOL (MFFRST) AND POLLUTION PREVENTION TOOL (MFFP2T)

EPA Science Inventory

This presentation will provide an overview of the USEPA's Metal Finishing Facility Risk Screening Tool, including a discussion of the models used and outputs. The tool is currently being expanded to include pollution prevention considerations as part of the model. The current st...

Treatment of Wastewater from Electroplating, Metal Finishing and Printed Circuit Board Manufacturing. Operation of Wastewater Treatment Plants Volume 4.

ERIC Educational Resources Information Center

California State Univ., Sacramento. Dept. of Civil Engineering.

One of four manuals dealing with the operation of wastewater plants, this document was designed to address the treatment of wastewater from electroplating, metal finishing, and printed circuit board manufacturing. It emphasizes how to operate and maintain facilities which neutralize acidic and basic waters; treat waters containing metals; destroy…

The influence of cervical finish line, internal relief, and cement type on the cervical adaptation of metal crowns.

PubMed

Bottino, Marco Antonio; Valandro, Luiz Felipe; Buso, Leonardo; Ozcan, Mutlu

2007-01-01

The aim of this investigation was to evaluate the cervical adaptation of metal crowns under several conditions, namely (1) variations in the cervical finish line of the preparation, (2) application of internal relief inside the crowns, and (3) cementation using different luting materials. One hundred eighty stainless-steel master dies were prepared simulating full crown preparations: 60 in chamfer (CH), 60 in 135-degree shoulder (OB), and 60 in rounded shoulder (OR). The finish lines were machined at approximate dimensions of a molar tooth preparation (height: 5.5 mm; cervical diameter: 8 mm; occlusal diameter: 6.4 mm; taper degree: 6; and cervical finish line width: 0.8 mm). One hundred eighty corresponding copings with the same finish lines were fabricated. A 30-Microm internal relief was machined 0.5 mm above the cervical finish line in 90 of these copings. The fit of the die and the coping was measured from all specimens (L0) prior to cementation using an optical microscope. After manipulation of the 3 types of cements (zinc phosphate, glass-ionomer, and resin cement), the coping was luted on the corresponding standard master die under 5-kgf loading for 4 minutes. Vertical discrepancy was again measured (L1), and the difference between L1 and L0 indicated the cervical adaptation. Significant influence of the finish line, cement type, and internal relief was observed on the cervical adaptation (P <.001). The CH type of cervical finish line resulted in the best cervical adaptation of the metal crowns regardless of the cement type either with or without internal relief (36.6 +/- 3 to 100.8 +/- 4 Microm) (3-way analysis of variance and Tukey's test, a = .05). The use of glass-ionomer cement resulted in the least cervical discrepancy (36.6 +/- 3 to 115 +/- 4 Microm) than those of other cements (45.2 +/- 4 to 130.3 +/- 2 Microm) in all conditions. The best cervical adaptation was achieved with the chamfer type of finish line. The internal relief improved the marginal

Agricultural Construction Volume II. Oxy-Gas and Other Cutting/Welding Processes. Woodworking, Metals, Finishing. Instructor's Guide.

ERIC Educational Resources Information Center

Admire, Myron; Maricle, Gary

This guide contains instructor's materials for teaching a secondary agricultural construction course consisting of instructional units on oxy-gas and other cutting and welding processes (10 lessons), woodworking (6 lessons), metals (10 lessons), and finishing (4 lessons). The materials for each unit include student objectives, a list of…

Effects of PCB Pad Metal Finishes on the Cu-Pillar/Sn-Ag Micro Bump Joint Reliability of Chip-on-Board (COB) Assembly

NASA Astrophysics Data System (ADS)

Kim, Youngsoon; Lee, Seyong; Shin, Ji-won; Paik, Kyung-Wook

2016-06-01

While solder bumps have been used as the bump structure to form the interconnection during the last few decades, the continuing scaling down of devices has led to a change in the bump structure to Cu-pillar/Sn-Ag micro-bumps. Cu-pillar/Sn-Ag micro-bump interconnections differ from conventional solder bump interconnections in terms of their assembly processing and reliability. A thermo-compression bonding method with pre-applied b-stage non-conductive films has been adopted to form solder joints between Cu pillar/Sn-Ag micro bumps and printed circuit board vehicles, using various pad metal finishes. As a result, various interfacial inter-metallic compounds (IMCs) reactions and stress concentrations occur at the Cu pillar/Sn-Ag micro bumps joints. Therefore, it is necessary to investigate the influence of pad metal finishes on the structural reliability of fine pitch Cu pillar/Sn-Ag micro bumps flip chip packaging. In this study, four different pad surface finishes (Thin Ni ENEPIG, OSP, ENEPIG, ENIG) were evaluated in terms of their interconnection reliability by thermal cycle (T/C) test up to 2000 cycles at temperatures ranging from -55°C to 125°C and high-temperature storage test up to 1000 h at 150°C. The contact resistances of the Cu pillar/Sn-Ag micro bump showed significant differences after the T/C reliability test in the following order: thin Ni ENEPIG > OSP > ENEPIG where the thin Ni ENEPIG pad metal finish provided the best Cu pillar/Sn-Ag micro bump interconnection in terms of bump joint reliability. Various IMCs formed between the bump joint areas can account for the main failure mechanism.

[Experimental analysis of finishing lines in ceramometal restorations].

PubMed

Gascón, F; Gil, J A; Fons, A; Badal, R

1990-11-01

The preparation is the first step of any tooth reconstruction. The biological integration of the protesis is depending on the marginal adaptation (finish line of the preparation), occlusal adaptation (occlusal reduction), longevity of the restoration (retention and luting) and esthetics. The effect the two finish line of the preparation is studied using experimental design. In porcelain-fused-to-metal the finish line of the preparation in chanfer is superior at the beveled shoulder, because proportioning better marginal adaptation.

Vitrified metal finishing wastes I. Composition, density and chemical durability.

PubMed

Bingham, P A; Hand, R J

2005-03-17

Durable phosphate glasses were formed by vitrifying waste filter cakes from two metal finishing operations. Some melts formed crystalline components during cooling. Compositional analysis of dried, heat treated and vitrified samples was made using energy-dispersive X-ray spectroscopy, X-ray fluorescence spectroscopy, inductively-coupled plasma spectroscopy and Leco induction furnace combustion analysis. Hydrolytic dissolution, measured by an adapted product consistency test, was reduced by up to 3 orders of magnitude upon heat treatment or vitrification, surpassing the performance of borosilicate glass in some cases. This was attributed to the high levels of iron and zinc in the wastes, which greatly improve the durability of phosphate glasses. One of the wastes arose from a metal phosphating process and was particularly suitable for vitrification due to its high P2O5 content and favourable melting behaviour. The other waste, which arose from a number of processes, was less suitable as it had a low P2O5 content and during heating it emitted harmful corrosive gases and underwent violent reactions. Substantial volume reductions were obtained by heat treatment and vitrification of both wastes. Compositions and performances of some vitrified wastes were comparable with those of glasses which are under consideration for the immobilisation of toxic and nuclear wastes.

Nearly Finished Genomes Produced Using Gel Microdroplet Culturing (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fitzsimmons, Michael

2012-06-01

Michael Fitzsimmons from Los Alamos National Laboratory gives a talk titled "Nearly Finished Genomes Produced Using Gel Microdroplet Culturing" at the 7th Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting held in June, 2012 in Santa Fe, NM.

Nearly Finished Genomes Produced Using Gel Microdroplet Culturing (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)

ScienceCinema

Fitzsimmons, Michael

2018-01-22

Michael Fitzsimmons from Los Alamos National Laboratory gives a talk titled "Nearly Finished Genomes Produced Using Gel Microdroplet Culturing" at the 7th Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting held in June, 2012 in Santa Fe, NM.

Toward Magnetorheological Finishing of Magnetic Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shafrir, S.N.; Lambropoulos, J.C.; Jacobs, S.D.

2007-10-24

Magnetorheological finishing (MRF) is a precision finishing process traditionally limited to processing only nonmagnetic materials, e.g., optical glasses, ceramics, polymers, and metals. Here we demonstrate that MRF can be used for material removal from magnetic material surfaces. Our approach is to place an MRF spot on machined surfaces of magnetic WC-Co materials. The resulting surface roughness is comparable to that produced on nonmagnetic materials. This spotting technique may be used to evaluate the depth of subsurface damage, or deformed layer, induced by earlier manufacturing steps, such as grinding and lapping.

Surface finish measurement studies

NASA Technical Reports Server (NTRS)

Teague, E. C.

1983-01-01

The performance of stylus instruments for measuring the topography of National Transonic Facility (NTF) model surfaces both for monitoring during fabrication and as an absolute measurement of topography was evaluated. It was found that the shop-grade instruments can damage the surface of models and that their use for monitoring fabrication procedures can lead to surface finishes that are substantially out of range in critical areas of the leading edges. The development of a prototype light-scattering instrument which would allow for rapid assessment of the surface finish of a model is also discussed.

Introducing National Center for Genome Resources (NCGR) Informatics (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)

ScienceCinema

Crow, John

2018-01-22

John Crow from the National Center for Genome Resources discusses his organization's informatics at the 7th Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting held in June, 2012 in Santa Fe, NM.

Introducing National Center for Genome Resources (NCGR) Informatics (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crow, John

2012-06-01

John Crow from the National Center for Genome Resources discusses his organization's informatics at the 7th Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting held in June, 2012 in Santa Fe, NM.

Magnetorheological finishing: a perfect solution to nanofinishing requirements

NASA Astrophysics Data System (ADS)

Sidpara, Ajay

2014-09-01

Finishing of optics for different applications is the most important as well as difficult step to meet the specification of optics. Conventional grinding or other polishing processes are not able to reduce surface roughness beyond a certain limit due to high forces acting on the workpiece, embedded abrasive particles, limited control over process, etc. Magnetorheological finishing (MRF) process provides a new, efficient, and innovative way to finish optical materials as well many metals to their desired level of accuracy. This paper provides an overview of MRF process for different applications, important process parameters, requirement of magnetorheological fluid with respect to workpiece material, and some areas that need to be explored for extending the application of MRF process.

Disassembly Properties of Cementitious Finish Joints Using an Induction Heating Method

PubMed Central

Ahn, Jaecheol; Noguchi, Takafumi; Kitagaki, Ryoma

2015-01-01

Efficient maintenance and upgrading of a building during its lifecycle are difficult because a cementitious finish uses materials and parts with low disassembly properties. Additionally, the reuse and recycling processes during building demolition also present numerous problems from the perspective of environmental technology. In this study, an induction heating (IH) method was used to disassemble cementitious finish joints, which are widely used to join building members and materials. The IH rapidly and selectively heated and weakened these joints. The temperature elevation characteristics of the cementitious joint materials were measured as a function of several resistor types, including wire meshes and punching metals, which are usually used for cementitious finishing. The disassembly properties were evaluated through various tests using conductive resistors in cementitious joints such as mortar. When steel fiber, punching metal, and wire mesh were used as conductive resistors, the cementitious modifiers could be weakened within 30 s. Cementitious joints with conductive resistors also showed complete disassembly with little residual bond strength.

Water resources of the Apostle Islands National Lakeshore, northern Wisconsin

USGS Publications Warehouse

Rose, W.J.

1988-01-01

Ground-water use in the National Lakeshore is primarily for consumption by Lakeshore visitors and employees. Of 14 wells constructed from 1979-84, 4 were finished in glacial sand and gravel, and 10 were finished in sandstone. Specific capacities ranged from 0.63 to 50 gallon per minute per foot. Average concentrations of dissolved solids are moderate and concentrations of heavy metals did not exceed Wisconsin's primary health standard.

Longer Sleep Durations Are Positively Associated With Finishing Place During a National Multiday Netball Competition.

PubMed

Juliff, Laura E; Halson, Shona L; Hebert, Jeffrey J; Forsyth, Peta L; Peiffer, Jeremiah J

2018-01-01

Juliff, LE, Halson, SL, Hebert, JJ, Forsyth, PL, and Peiffer, JJ. Longer sleep durations are positively associated with finishing place during a national multiday netball competition. J Strength Cond Res 32(1): 189-194, 2018-Sleep is often regarded as the single best recovery strategy available to an athlete, yet little is known about the quality and quantity of sleep in athletes during multiday competitions. This study objectively evaluated sleep characteristics of athletes during a national netball tournament. Using wrist actigraphy monitors and sleep diaries, 42 netballers from 4 state teams were monitored for the duration of a tournament (6 days) and 12 days before in home environments. Significant differences were found between teams based on final competition standings, suggesting enhanced sleep characteristics in athlete's whose team finished higher in the tournament standings. The top 2 placed teams when compared with the lower 2 placed teams slept longer (8:02 ± 36:43; 7:01 ± 27:33), had greater time in bed (9:03 ± 0:52; 7:59 ± 0:54) and reported enhanced subjective sleep ratings (2.6 ± 0.5; 2.3 ± 0.6). Sleep efficiency was no different between teams. A strong correlation (r = -0.68) was found indicating longer sleep durations during competition were associated with higher final tournament positions. Encouraging athletes to aim for longer sleep durations in competition, where possible, may influence the outcome in tournament style competitions.

The Finish Line.

ERIC Educational Resources Information Center

Cohen, Andrew

1998-01-01

Details what is expected in a good floor finish for athletic facilities, and explores the different categories of finishes and their content within the context of environmental regulation and manufacturing standards. Also discusses urethane finishings, the debate over using waterbased finishes, and the influence of regulatory control that may…

Feed-conversion ratio of finisher pigs in the USA.

PubMed

Losinger, W C

1998-10-09

Although the feed-conversion ratio is recognized as a prominent indicator of profitability for pork producers, only 212 (50.7%) of 418 producers who were asked the feed-conversion ratio for finisher pigs provided a response during the USA National Animal Health Monitoring System 1995 National Swine Study. Of these, 126 (59.4%) producers furnished a feed-conversion ratio which they characterized as having been calculated from records, while 86 (40.6%) gave a response that they characterized as estimated or guessed. Feed-conversion ratios ranged from 2.18 to 5.91 kg of feed fed for each kg of live-body weight gained during the grower/finisher phase, with a mean of 3.28 and a standard deviation of 0.52. Stepwise regression revealed the following management factors to be associated with improved feed-conversion ratios: > or = 3 different rations fed during the grower/finisher phase (P < 0.01); no rations mixed on the farm (P < 0.05); and not giving chlortetracycline in feed or water as a disease preventive or growth promotant (P < 0.01). In addition, operations where > or = 3000 pigs entered the grower/finisher-production phase during the six-month period prior to interview had a better mean feed-conversion ratio than operations where < 3000 pigs entered the grower/finisher phase (P < 0.01).

Automated Finishing with Autofinish

PubMed Central

Gordon, David; Desmarais, Cindy; Green, Phil

2001-01-01

Currently, the genome sequencing community is producing shotgun sequence data at a very high rate, but finishing (collecting additional directed sequence data to close gaps and improve the quality of the data) is not matching that rate. One reason for the difference is that shotgun sequencing is highly automated but finishing is not: Most finishing decisions, such as which directed reads to obtain and which specialized sequencing techniques to use, are made by people. If finishing rates are to increase to match shotgun sequencing rates, most finishing decisions also must be automated. The Autofinish computer program (which is part of the Consed computer software package) does this by automatically choosing finishing reads. Autofinish is able to suggest most finishing reads required for completion of each sequencing project, greatly reducing the amount of human attention needed. Autofinish sometimes completely finishes the project, with no human decisions required. It cannot solve the most complex problems, so we recommend that Autofinish be allowed to suggest reads for the first three rounds of finishing, and if the project still is not finished completely, a human finisher complete the work. We compared this Autofinish-Hybrid method of finishing against a human finisher in five different projects with a variety of shotgun depths by finishing each project twice—once with each method. This comparison shows that the Autofinish-Hybrid method saves many hours over a human finisher alone, while using roughly the same number and type of reads and closing gaps at roughly the same rate. Autofinish currently is in production use at several large sequencing centers. It is designed to be adaptable to the finishing strategy of the lab—it can finish using some or all of the following: resequencing reads, reverses, custom primer walks on either subclone templates or whole clone templates, PCR, or minilibraries. Autofinish has been used for finishing cDNA, genomic clones, and

Clean Metal Finishing Alternatives

DTIC Science & Technology

2006-05-01

Cr, must heat treat for hardness 4 4 Trivalent chrome Trivalent plating chemistry Varying success, some must be brush plate 3 3 Alloy plating...metals. Hard coating deposition unproven. 3 N/A Weld coating Electrospark Deposition/ Alloying (ESD/ ESA) Microarc welding Localized repair of non...Alternatives to chromate conversion coatings Al TriChrome Pretreatment (TCP)* – AnoChem TCP, Aluminescent, TCP-HF Trivalent Cr3+ conversion with Zr

Contamination of Polish national parks with heavy metals.

PubMed

Staszewski, Tomasz; Łukasik, Włodzimierz; Kubiesa, Piotr

2012-07-01

The paper presents results of screening analysis of all Polish national parks (23) contamination with Cd, Cu, Pb and Zn on the basis of a three-level characteristic of heavy metal presence in Norway spruce stands: accumulation on the needle surface, concentration of heavy metals in spruce needles and concentration of bioavailable heavy metals in the soil. Based on the obtained results, the classification of forest ecosystem hazard in national parks with heavy metals was made using synthetic indicators. It was found out that Babiogórski, Magurski, Ojcowski and Gorczański National Parks, located in the southern part of the country, were the most polluted with heavy metals. It is probably due to a higher industrial activity in this part of Poland and the transboundary transport of air pollutants. A little lower level of pollution was observed in Kampinoski National Park located in the middle of the country. The concentration of heavy metals found in needles from national parks does not seem to be harmful for the health status of the trees. Statistically significant correlation between all parameters, which was found for cadmium--the most mobile of the analysed elements--shows that this metal can be proposed as a marker to reflect present effect of industrial emission on forests.

Effects of surface-finishing protocols on the roughness, color change, and translucency of different ceramic systems.

PubMed

Akar, Gülcan Coşkun; Pekkan, Gürel; Çal, Ebru; Eskitaşçıoğlu, Gürcan; Özcan, Mutlu

2014-08-01

Surface-finishing protocols have a mechanical impact on ceramic surfaces that could eventually affect surface topography and light scattering. An optimum protocol is needed to avoid damaging the optical properties of ceramics. The purpose of this study was to determine the effects of different surface-finishing protocols on the surface roughness, color change, and translucency of ceramic and metal ceramic restorations. Standardized disk-shaped specimens (1.5 × 10 mm, n=128) were fabricated from 3 different ceramic core materials (aluminum oxide [Al2O3]-AL, zirconium oxide [ZrO2]-ZR, lithium disilicate [Li2Si2O5]-LIT), veneered (V) with dentin ceramics (n=32 per group), and placed in the following groups: ALV, ZRV, and LITV. The metal ceramic group acted as the control (n=32). Four different surface-finishing methods were tested. Airborne-particle abrasion with 50 μm Al2O3, polishing with adjustment kit, polishing with adjustment kit plus diamond polishing paste, and autoglazing (n=8 subgroup) were applied on the veneering ceramics. The specimens were analyzed with a profilometer for surface roughness, and color change and translucency were measured with a clinical spectrophotometer. Statistical analyses were performed with 1-way ANOVA and the Tukey honest significant difference tests (α=.05). Specimens treated with the airborne particle abrasion method showed significantly higher mean profilometer for surface roughness values in all groups (P<.05). The polishing with adjustment kit and autoglazing methods revealed statistically similar surface roughness values in all groups (P>.05). With the diamond polishing paste method, lower surface roughness values were achieved in the ZRV and metal ceramic groups acted as the control groups. Different surface-finishing methods affected the color change of the ceramic systems, except for ZRV. Surface-finishing protocols significantly affected the translucency values of the ALV, LITV, and metal ceramic groups (P<.05). No

AMMONIA EMISSION FACTORS FROM SWINE FINISHING OPERATIONS

EPA Science Inventory

The paper presents results from two new studies at swine finishing facilities. (NOTE: Concentrated animal feeding operations (CAFOs) are being examined in several regions of the U,.S. as major sources of ammonia and particulate matter precursors. EPA's National Risk Management Re...

AMMONIA EMISSION FACTORS FROM SWINE FINISHING OPERATIONS

EPA Science Inventory

The paper presents results from two new studies at swine finishing facilities. (NOTE: Concentrated anaimal feeding operations (CAFOs) are being examined in several regions of the U.S. as major sources of ammonia and particulate matter precursors. EPA's National Risk Management Re...

40 CFR 141.511 - What is required of new finished water reservoirs?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Enhanced Filtration and Disinfection-Systems Serving Fewer Than 10,000 People Finished Water Reservoirs § 141.511 What is required of... 40 Protection of Environment 22 2010-07-01 2010-07-01 false What is required of new finished water...

40 CFR 141.511 - What is required of new finished water reservoirs?

Code of Federal Regulations, 2012 CFR

2012-07-01

...) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Enhanced Filtration and Disinfection-Systems Serving Fewer Than 10,000 People Finished Water Reservoirs § 141.511 What is required of... 40 Protection of Environment 24 2012-07-01 2012-07-01 false What is required of new finished water...

40 CFR 141.511 - What is required of new finished water reservoirs?

Code of Federal Regulations, 2011 CFR

2011-07-01

...) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Enhanced Filtration and Disinfection-Systems Serving Fewer Than 10,000 People Finished Water Reservoirs § 141.511 What is required of... 40 Protection of Environment 23 2011-07-01 2011-07-01 false What is required of new finished water...

40 CFR 141.511 - What is required of new finished water reservoirs?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Enhanced Filtration and Disinfection-Systems Serving Fewer Than 10,000 People Finished Water Reservoirs § 141.511 What is required of... 40 Protection of Environment 24 2013-07-01 2013-07-01 false What is required of new finished water...

Electromigration Failure Mechanism in Sn-Cu Solder Alloys with OSP Cu Surface Finish

NASA Astrophysics Data System (ADS)

Chu, Ming-Hui; Liang, S. W.; Chen, Chih; Huang, Annie T.

2012-09-01

Organic solderable preservative (OSP) has been adopted as the Cu substrate surface finish in flip-chip solder joints for many years. In this study, the electromigration behavior of lead-free Sn-Cu solder alloys with thin-film under bump metallization and OSP surface finish was investigated. The results showed that severe damage occurred on the substrate side (cathode side), whereas the damage on the chip side (cathode side) was not severe. The damage on the substrate side included void formation, copper dissolution, and formation of intermetallic compounds (IMCs). The OSP Cu interface on the substrate side became the weakest point in the solder joint even when thin-film metallization was used on the chip side. Three-dimensional simulations were employed to investigate the current density distribution in the area between the OSP Cu surface finish and the solder. The results indicated that the current density was higher along the periphery of the bonding area between the solder and the Cu pad, consistent with the area of IMC and void formation in our experimental results.

Metal Whiskers: A Discussion of Risks and Mitigation

DTIC Science & Technology

2010-11-30

efforts to investigate – Chromate conversion finishes DO NOT appear to stop whisker formation [4] S. Arnold, "Repressing the Growth of Tin Whiskers...November 30, 2010 Metal Whiskers 10 Examples of Metal Whiskers Zinc-Plated Steel Bus Rail with Yellow Chromate Conversion Finish Zinc whiskers grew...Metal Whiskers 11 Examples of Metal Whiskers Tin-Plated D-Sub Connector Shell Connector Advertised as “RoHS Compliant” November 30, 2010 Metal

FINISHING FABRICATED METAL PRODUCTS WITH ...

EPA Pesticide Factsheets

This report provides a technical and economic evaluation of a polyester powder coating system applied to the exterior and interior surfaces of metal boxes fabricated for the telephone and cable industries. This evaluation summarized many of the requirements and benefits of a clean technology that effectively eliminates the use of hazardous solvents and prevents the generation of volatile organic emissions and hazardous solid waste. publish information

40 CFR 141.510 - Is my system subject to the new finished water reservoir requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... finished water reservoir requirements? 141.510 Section 141.510 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Enhanced Filtration and Disinfection-Systems Serving Fewer Than 10,000 People Finished Water Reservoirs § 141.510 Is...

40 CFR 141.510 - Is my system subject to the new finished water reservoir requirements?

Code of Federal Regulations, 2011 CFR

2011-07-01

... finished water reservoir requirements? 141.510 Section 141.510 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Enhanced Filtration and Disinfection-Systems Serving Fewer Than 10,000 People Finished Water Reservoirs § 141.510 Is...

An atomic-scale and high efficiency finishing method of zirconia ceramics by using magnetorheological finishing

NASA Astrophysics Data System (ADS)

Luo, Hu; Guo, Meijian; Yin, Shaohui; Chen, Fengjun; Huang, Shuai; Lu, Ange; Guo, Yuanfan

2018-06-01

Zirconia ceramics is a valuable crucial material for fabricating functional components applied in aerospace, biology, precision machinery, military industry and other fields. However, the properties of its high brittleness and high hardness could seriously reduce its finishing efficiency and surface quality by conventional processing technology. In this work, we present a high efficiency and high-quality finishing process by using magnetorheological finishing (MRF), which employs the permanent magnetic yoke with straight air gap as excitation unit. The sub-nanoscale surface roughness and damage free surface can be obtained after magnetorheological finishing. The XRD results and SEM morphologies confirmed that the mechanical shear removal with ductile modes are the dominant material removal mechanism for the magnetorheological finishing of zirconia ceramic. With the developed experimental apparatus, the effects of workpiece speed, trough speed and work gap on material removal rate and surface roughness were systematically investigated. Zirconia ceramics finished to ultra-smooth surface with surface roughness less than Ra 1 nm was repeatedly achieved during the parametric experiments. Additionally, the highest material removal rate exceeded 1 mg/min when using diamond as an abrasive particle. Magnetorheological finishing promises to be an adaptable and efficient method for zirconia ceramics finishing.

RECOVERY OF METAL USING ALUMINUM DISPLACEMENT

EPA Science Inventory

The removal of typical metals (Cu, Pb, Sn, Ni) from printed circuit and metal finishing waste streams was evaluated using displacement with aluminum. he metal is recovered as non-hazardous metal particles and can be recycled by smelting. n acceptable aluminum metal configuration ...

Carcass quality and meat tenderness of Hawaii pasture-finished cattle and Hawaii-originated, mainland feedlot-finished cattle.

PubMed

Kim, Yong Soo; Fukumoto, Glen Kazumi; Kim, Sunae

2012-10-01

The objective of this study was to compare the carcass quality and meat tenderness of Hawaii cattle finished on subtropical pasture with those of mainland US feedlot-finished cattle that were shipped from Hawaii after weaning. Rib-eye steak samples were collected from 30 feedlot-finished cattle harvested at a slaughter house in Washington State, USA and from 13 subtropical pasture-finished cattle harvested at a local slaughter house in Hawaii, then shipped to meat science laboratory at the University of Hawaii, Manoa. Samples were aged for 2 weeks at 4°C and frozen for later proximate analysis and meat tenderness measurement. Feedlot-finished cattle had significantly heavier carcass weight (353 vs 290 kg) and thicker backfat (13.5 vs 6.6 mm), but no significant difference was observed in rib-eye area between the two groups. Marbling score (Small) and United States Department of Agriculture quality grade (Choice) of the pasture-finished beef were not significantly (P < 0.05) different from those of feedlot-finished beef. The shear force value of pasture-finished beef (5.18 kg) was not statistically different (P < 0.05) from that of feedlot-finished beef (4.40 kg). In conclusion, results of this study suggest that Hawaii cattle finished on subtropical pasture produced as tender beef as mainland feedlot-finished cattle with less intramuscular fat.

Finishing of wood

Treesearch

R. Sam Williams

1999-01-01

The primary function of any wood finish (paint, varnish, and stain, for example) is to protect the wood surface, help maintain a certain appearance, and provide a cleanable surface. Although wood can be used both outdoors and indoors without finishing, unfinished wood surfaces exposed to the weather change color, are roughened by photodegradation and surface checking,...

Fluoroalkyl Siloxanes as Liquid-Repellent Fabric Finishes. Part 2. The Homopolymers and their Copolymers with Alkyl Silanes

DTIC Science & Technology

1979-06-01

LUOROALKYL SILOXANES AS LIQUID-JEPELLENT FABiRIC FINISHES YARUJF- THE 1OMOPOLYMERS AND /,THEIR CUPOLYMERS WITH !IxKL LALEK i.W o D DC BEST AVAILABLE...NATIONAL DEFENCE CANADA DEFENCE RESEARCH ESTABLISHMENT OTTAWA REPORT NO. 804 FLUOROALKYL SILOXANES AS LIQUID-REPELLENT FABRIC FINISHES PART II THE...cent) and cotton as finishes , and the oil and water repellency imparted to these fabrics ascertained by standard tests. In this manner it is possible

Study of strength properties of semi-finished products from economically alloyed high-strength aluminium-scandium alloys for application in automobile transport and shipbuilding

NASA Astrophysics Data System (ADS)

Baranov, Vladimir; Sidelnikov, Sergey; Zenkin, Evgeny; Frolov, Viktor; Voroshilov, Denis; Yakivyuk, Olga; Konstantinov, Igor; Sokolov, Ruslan; Belokonova, Irina

2018-04-01

The results of a study on the strength of rolled products from aluminium alloys doped with scandium under various processing conditions of hot and cold rolling are presented. The regularities of metal flow and the level of strength of deformed semi-finished products from aluminum-scandium alloys are established, depending on the total degree of deformation and the various modes of single reduction during rolling. It is shown that when using one heating of a cast billet to obtain high-quality semi-finished products, the temperature during the rolling process should not be lower than 350-370°, and the total degree of deformation does not exceed 50-60%. It was found that the semi-finished products from alloys with a content of scandium in the range 0.11-0.12% in the deformed state had elevated values of ultimate tensile strength and yield strength of the metal, which allows them to be recommended for industrial production of sheet metal products.

3D FE simulation of semi-finishing machining of Ti6Al4V additively manufactured by direct metal laser sintering

NASA Astrophysics Data System (ADS)

Imbrogno, Stano; Rinaldi, Sergio; Raso, Antonio; Bordin, Alberto; Bruschi, Stefania; Umbrello, Domenico

2018-05-01

The Additive Manufacturing techniques are gaining more and more interest in various industrial fields due to the possibility of drastically reduce the material waste during the production processes, revolutionizing the standard scheme and strategies of the manufacturing processes. However, the metal parts shape produced, frequently do not satisfy the tolerances as well as the surface quality requirements. During the design phase, the finite element simulation results a fundamental tool to help the engineers in the correct decision of the most suitable process parameters, especially in manufacturing processes, in order to produce products of high quality. The aim of this work is to develop a 3D finite element model of semi-finishing turning operation of Ti6Al4V, produced via Direct Metal Laser Sintering (DMLS). A customized user sub-routine was built-up in order to model the mechanical behavior of the material under machining operations to predict the main fundamental variables as cutting forces and temperature. Moreover, the machining induced alterations are also studied by the finite element model developed.

Finishing Techniques for Silicon Nitride Bearings

DTIC Science & Technology

1976-03-01

finishing procedures. Rolling contact fatigue lives of silicon nitride with selected smoother finishes tested at 800 ksi Hertz stress were an order...grinding. Rolling contact fatigue lives of silicon nitride with selected smoother finishes tested at 800 ksi Hertz stress were an order of magnitude...lives of silicon nitride with selected smoother finishes tested at 800 ksi Hertz stress were an order of magnitude longer than those

Percent recoveries of anthropogenic organic compounds with and without the addition of ascorbic acid to preserve finished-water samples containing free chlorine, 2004-10

USGS Publications Warehouse

Valder, Joshua F.; Delzer, Gregory C.; Bender, David A.; Price, Curtis V.

2011-01-01

This report presents finished-water matrix-spike recoveries of 270 anthropogenic organic compounds with and without the addition of ascorbic acid to preserve water samples containing free chlorine. Percent recoveries were calculated using analytical results from a study conducted during 2004-10 for the National Water-Quality Assessment (NAWQA) Program of the U.S. Geological Survey (USGS). The study was intended to characterize the effect of quenching on finished-water matrix-spike recoveries and to better understand the potential oxidation and transformation of 270 anthropogenic organic compounds. The anthropogenic organic compounds studied include those on analytical schedules 1433, 2003, 2033, 2060, 2020, and 4024 of the USGS National Water Quality Laboratory. Three types of samples were collected from 34 NAWQA locations across the Nation: (1) quenched finished-water samples (not spiked), (2) quenched finished-water matrix-spike samples, and (3) nonquenched finished-water matrix-spike samples. Percent recoveries of anthropogenic organic compounds in quenched and nonquenched finished-water matrix-spike samples are presented. Comparisons of percent recoveries between quenched and nonquenched spiked samples can be used to show how quenching affects finished-water samples. A maximum of 18 surface-water and 34 groundwater quenched finished-water matrix-spike samples paired with nonquenched finished-water matrix-spike samples were analyzed. Percent recoveries for the study are presented in two ways: (1) finished-water matrix-spike samples supplied by surface-water or groundwater, and (2) by use (or source) group category for surface-water and groundwater supplies. Graphical representations of percent recoveries for the quenched and nonquenched finished-water matrix-spike samples also are presented.

Pb-free surface-finishing on electronic components' terminals for Pb-free soldering assembly

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tanaka, Hitoshi; Tanimoto, Morimasa; Matsuda, Akira

1999-11-01

Pb-free solderable surface finishing is essential to implement Pb-free solder assembly in order to meet with the growing demand of environmental consciousness to eliminate Pb from electronic products. Two types of widely applicable Pb-free surface finishing technologies are developed. One is the multilayer-system including Pd with Ni undercoat. Heat-resistance of Pd enables whole-surface-plating on to leadframe before IC-assembling process. The other is the double-layer-system with low-melting-point-materials, for example, thicker Sn underlayer and thinner Sn-Bi alloy overlayer, dilutes Sn-Bi alloy's defects of harmful reactivity along with substrate metal and mechanical brittleness with keeping its advantages of solder-wettability and no whisker.

Pesticides and their breakdown products in Lake Waxahachie, Texas, and in finished drinking water from the lake

USGS Publications Warehouse

Ging, Patricia B.

2002-01-01

Since 1991, the U.S. Geological Survey (USGS) National Water-Quality Assessment (NAWQA) Program has collected pesticide data from streams and aquifers throughout the Nation (Gilliom and others, 1995). However, little published information on pesticides in public drinking water is available. The NAWQA Program usually collects data on the sources of drinking water but not on the finished drinking water. Therefore, the U.S. Environmental Protection Agency (USEPA), in conjunction with the NAWQA Program, has initiated a nationwide pilot project to collect information on concentrations of pesticides and their breakdown products in finished drinking water, in source waters such as reservoirs, and in the basins that contribute water to the reservoirs. The pilot project was designed to collect water samples from finished drinking-water supplies and the associated source water from selected reservoirs that receive runoff from a variety of land uses. Lake Waxahachie, in Ellis County in north-central Texas, was chosen to represent a reservoir receiving water that includes runoff from cotton cropland. This fact sheet presents the results of pesticide sampling of source water from Lake Waxahachie and in finished drinking water from the lake. Analyses are compared to indicate differences in pesticide detections and concentrations between lake water and finished drinking water.

40 CFR 141.714 - Requirements for uncovered finished water storage facilities.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 23 2014-07-01 2014-07-01 false Requirements for uncovered finished water storage facilities. 141.714 Section 141.714 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Enhanced Treatment for Cryptosporidium Treatment Technique...

The First Amendment: The Finished Mystery Case and World War I.

ERIC Educational Resources Information Center

Mueller, Jean West; Schamel, Wynell Burroughs

1990-01-01

Introduces the censorship, and imprisonment of Jehovah's Witnesses who distributed, "The Finished Mystery," which contained antiwar statements deemed seditious during World War I. Asks students to examine a Justice Department document pertaining to the case. Helps students decide whether national security needs should override First…

27 CFR 25.231 - Finished beer.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Finished beer. 25.231... OF THE TREASURY LIQUORS BEER Beer Purchased From Another Brewer § 25.231 Finished beer. (a) A brewer may obtain beer in barrels and kegs, finished and ready for sale from another brewer. The purchasing...

27 CFR 25.231 - Finished beer.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2014-04-01 2014-04-01 false Finished beer. 25.231... OF THE TREASURY ALCOHOL BEER Beer Purchased From Another Brewer § 25.231 Finished beer. (a) A brewer may obtain beer in barrels and kegs, finished and ready for sale from another brewer. The purchasing...

27 CFR 25.231 - Finished beer.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2012-04-01 2012-04-01 false Finished beer. 25.231... OF THE TREASURY LIQUORS BEER Beer Purchased From Another Brewer § 25.231 Finished beer. (a) A brewer may obtain beer in barrels and kegs, finished and ready for sale from another brewer. The purchasing...

27 CFR 25.231 - Finished beer.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2013-04-01 2013-04-01 false Finished beer. 25.231... OF THE TREASURY ALCOHOL BEER Beer Purchased From Another Brewer § 25.231 Finished beer. (a) A brewer may obtain beer in barrels and kegs, finished and ready for sale from another brewer. The purchasing...

27 CFR 25.231 - Finished beer.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2011-04-01 2011-04-01 false Finished beer. 25.231... OF THE TREASURY LIQUORS BEER Beer Purchased From Another Brewer § 25.231 Finished beer. (a) A brewer may obtain beer in barrels and kegs, finished and ready for sale from another brewer. The purchasing...

Design and Feasibility Testing of the truth FinishIt Tobacco Countermarketing Brand Equity Scale.

PubMed

Evans, W Douglas; Rath, Jessica; Pitzer, Lindsay; Hair, Elizabeth C; Snider, Jeremy; Cantrell, Jennifer; Vallone, Donna

2016-07-01

The original truth campaign was a branded, national smoking prevention mass media effort focused on at-risk youth ages 12-17. Today the truth brand focuses on the goal of finishing tobacco (truth FinishIt). There have been significant changes in the tobacco control landscape, leading FinishIt to focus on 15- to 21-year-olds. The present article reports on formative research and media monitoring data collected to pilot test a new truth FinishIt brand equity scale. The goals of this study were to (a) content analyze truth FinishIt mass media ads, (b) assess truth's social media and followers' perceptions of truth's digital brand identity, and (c) develop and feasibility test a new version of the truth FinishIt brand equity scale using data from an existing Truth Initiative media monitoring study. Through factor analysis, we identified a brand equity scale, as in previous research, consisting of 4 main constructs: brand loyalty, leadership/satisfaction, personality, and awareness. Targeted truth attitudes and beliefs about social perceptions, acceptability, and industry-related beliefs were regressed on the higher order factor and each of the 4 individual brand equity factors. Ordinary least squares regression models generally showed associations in the expected directions (positive for anti-tobacco and negative for pro-tobacco) between targeted attitudes/beliefs and truth FinishIt brand equity. This study succeeded in developing and validating a new truth FinishIt brand equity scale. The scale may be a valuable metric for future campaign evaluation. Future studies should examine the effects of truth FinishIt brand equity on tobacco use behavioral outcomes over time.

71. September 1913 "No. 113. Some of the finished bitulithic ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

71. September 1913 "No. 113. Some of the finished bitulithic or bituminous macadam road after being sanded and rolled, in the foreground. In the middle distance men are applying oil to incomplete section. In the far distance, roller is working on foundation course." - Crater Lake National Park Roads, Klamath Falls, Klamath County, OR

9 CFR 381.309 - Finished product inspection.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Finished product inspection. (a) Finished product inspections must be handled according to: (1) A HACCP.... (b)-(c) [Reserved] (d) Procedures for finished product inspections where the HACCP plan for thermally...

Finishing Using Next Generation Technologies

ScienceCinema

Van Tonder, Andries

2018-01-16

Andries van Tonder of Wellcome Trust Sanger Institute discusses a pipeline for finishing genomes to the gold standard on June 3, 2010 at the "Sequencing, Finishing, Analysis in the Future" meeting in Santa Fe, NM.

26. A battery of calender presses at work finishing magazine ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

26. A battery of calender presses at work finishing magazine paper. After the coated paper has been dried and put into rolls, as shown in the preceding pictures, it is brought to the room shown here. A roll is put in the reel at the man's shoulder in the foreground and started through the machine. It passes between the two top rollers and then in and out between the succeeding rollers, until it reaches the bottom. Many tons' pressure have ironed it before it comes out and is rolled up again. This process gives it the finish that the National Geographic must have to maintain its high standard. (p.240.) - Champion-International Paper Company, West bank of Spicket River at Canal Street, Lawrence, Essex County, MA

IET. Control and equipment building (TAN620). Details and room finish ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

IET. Control and equipment building (TAN-620). Details and room finish schedule. Ralph M. Parsons 902-4-ANP-620-A 322. Approved by INEEL Classification Office for public release. INEEL index code no. 035-0629-00-693-106907 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

25 CFR 301.8 - Finish.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 2 2010-04-01 2010-04-01 false Finish. 301.8 Section 301.8 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER AND TURQUOISE PRODUCTS; STANDARDS § 301.8 Finish. All silver is to be hand polished. ...

Surface Preparation Methods to Enhance Dynamic Surface Property Measurements of Shocked Metal Surfaces

NASA Astrophysics Data System (ADS)

Zellner, Michael; McNeil, Wendy; Gray, George, III; Huerta, David; King, Nicholas; Neal, George; Payton, Jeremy; Rubin, Jim; Stevens, Gerald; Turley, William; Buttler, William

2008-03-01

This effort investigates surface-preparation methods to enhance dynamic surface-property measurements of shocked metal surfaces. To assess the ability of making reliable and consistent dynamic surface-property measurements, the amount of material ejected from the free-surface upon shock release to vacuum (ejecta) was monitored for shocked Al-1100 and Sn targets. Four surface preparation methods were considered: fly-cut machined finish, diamond-turned machine finish, polished finish, and ball-rolled. The samples were shock loaded by in-contact detonation of HE PBX-9501 on the front-side of the metal coupons. Ejecta production at the back-side or free-side of the metal coupons was monitored using piezoelectric pins, optical shadowgraphy, and x-ray attenuation radiography.

Surface preparation methods to enhance dynamic surface property measurements of shocked metal surfaces

NASA Astrophysics Data System (ADS)

Zellner, M. B.; Vogan McNeil, W.; Gray, G. T.; Huerta, D. C.; King, N. S. P.; Neal, G. E.; Valentine, S. J.; Payton, J. R.; Rubin, J.; Stevens, G. D.; Turley, W. D.; Buttler, W. T.

2008-04-01

This effort investigates surface-preparation methods to enhance dynamic surface-property measurements of shocked metal surfaces. To assess the ability of making reliable and consistent dynamic surface-property measurements, the amount of material ejected from the free surface upon shock release to vacuum (ejecta) was monitored for shocked Al-1100 and Sn targets. Four surface-preparation methods were considered: Fly-cut machine finish, diamond-turned machine finish, polished finish, and ball rolled. The samples were shock loaded by in-contact detonation of HE PBX-9501 on the front side of the metal coupons. Ejecta production at the back side or free side of the metal coupons was monitored using piezoelectric pins, optical shadowgraphy, and x-ray attenuation radiography.

27 CFR 19.601 - Finished products records.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Finished products records. (a) Bottling and packaging. A proprietor must maintain daily transaction records and a daily summary record of the kind and quantity of finished products bottled or packaged within... daily records of the disposition of finished products from the processing account at the distilled...

Friction modifier using adherent metallic multilayered or mixed element layer conversion coatings

NASA Technical Reports Server (NTRS)

Schramm, Harry F. (Inventor); Defalco, Frank G. (Inventor); Starks, Sr., Lloyd L. (Inventor)

2012-01-01

A process for creating conversion coatings and spin, drawing, and extrusion finishes for surfaces, wherein the conversion coatings and spin, drawing, and extrusion finishes contain potassium, phosphorus, nitrogen, silicon, and one or more non-alkaline metals. The process comprises forming a first aqueous solution of silicate, potassium hydroxide, and ammonium hydroxide; forming a second aqueous solution of water, phosphoric acid, ammonium hydroxide, an alkali metal hydroxide, and one or more non-alkaline metals, and then combining the first solution with the second solution to form a final solution. This final solution forms an anti-friction multi-layer conversion coating or a spin, drawing, and extrusion finish on a surface when applied to the surface, either directly or as an additive in lubricating fluids.

Friction Modifier Using Adherent Metallic Multilayered or Mixed Element Layer Conversion Coatings

NASA Technical Reports Server (NTRS)

Schramm, Harry F. (Inventor); Defalco, Francis G. (Inventor); Starks, Lloyd L., Sr. (Inventor)

2013-01-01

A process for creating conversion coatings and spin, drawing, and extrusion finishes for surfaces, wherein the conversion coatings and spin, drawing, and extrusion finishes contain potassium, phosphorus, nitrogen, and one or more non-alkaline metals and/or one or more metalloids. The process comprises forming an aqueous solution of water, phosphoric acid or sulfuric acid, ammonium hydroxide, an alkali metal hydroxide, and one or more non-alkaline metals and/or one or more metalloids. The aqueous solution forms an anti-friction multilayer conversion and/or mixed element coating or a spin, drawing, and extrusion finish on a surface when applied to the surface, either directly without the use of applied external electromotive force, or as an additive in lubricating fluids.

On the properties of two binary NiTi shape memory alloys. Effects of surface finish on the corrosion behaviour and in vitro biocompatibility.

PubMed

Es-Souni, Mohammed; Es-Souni, Martha; Fischer-Brandies, Helge

2002-07-01

The present paper compares the transformation behaviour and mechanical properties of two orthodontic wires of close chemical compositions. The effects of surface topography and surface finish residues on the potentiodynamic corrosion behaviour and biocompatibility are also reported. The cytotoxicity tests were performed on both alloys in fibroblast cell cultures from human gingiva using the MTT test. It is shown that the surface finish and the amounts of surface finish residues affect dramatically the corrosion resistance. Bad surface finish results in lower corrosion resistance. The in vitro biocompatibility, though not affected to the extent of corrosion resistance, is also reduced as the surface roughness and the amounts of residues increase. This is thought to be due to surface effects on corrosion and metallic ions release.

The Effect of Various Finish Line Configurations on the Marginal Seal and Occlusal Discrepancy of Cast Full Crowns After Cementation - An In-vitro Study.

PubMed

Nemane, Vaishali; Akulwar, Ravikumar Suryakanth; Meshram, Suresh

2015-08-01

The marginal fit of crowns is of clinical importance. It is found that marginal and occlusal discrepancies are commonly increased following cementation. The resistance of cementing materials is a factor that prevents cast restorations from being correctly seated. Different finish lines behave differently in facilitating the escape of the cement. When the escape path of the cement decreases, the crown fails to seat further. This study was planned with an aim to evaluate the effect of various finish lines on the marginal seal and occlusal seat of full crown preparations. Six stainless steel metal dies were machined to simulate molar crown preparations. The diameter was 10 mm and height was 6mm. The occlusal surface was kept flat and a small circular dimple was machined for reorientation of the wax pattern and metal copings, margins of various designs were machined accurately. The margins prepared were Group A- 90(0)C shoulder, Group B- Rounded shoulder, Group C- 45 degree sloped shoulder, Group D- Chamfer, Group E- Long chamfer, Group F- Feather edge. Full cast metal crowns of base metal alloy were fabricated over the metal dies. Zinc phosphate luting cement was used for the cementation. After twenty four hours, the cemented crown and die assembly were embedded in clear acrylic resin so as to hold the assembly together while sectioning. Twenty four hours later, all the samples were sectioned sagitally. The sectioned halves were focused under a stereomicroscope and the cement spaces were measured to the nearest micron. The cement thickness was measured at two points on the occlusal surface and one at each margin. Significant differences were observed in the occlusal seat and marginal seal of all the finish line configurations. The rounded shoulder had the best occlusal seat, followed by 90(0)C shoulder. The occlusal seat and marginal seal afforded by the shoulder finish lines were similar whereas there was a vast difference in the seating and sealing of long chamfer

Forest Products Laboratory natural finish

Treesearch

J. M. Black; D. F. Laughnan; E. A. Mraz

1979-01-01

A simple and durable exterior natural finish developed at the Forest Products Laboratory is described. The finish is classified as a semi-transparent oil-base penetrating stain that effectively retains much of the natural grain and texture of wood when exposed to the weather. The directions for preparation are included as are the recommendations for application to both...

Heavy Metal.

ERIC Educational Resources Information Center

Shoemaker, W. Lee

1998-01-01

Discusses the advantages, both functional and economic, of using a standing-seam metal roof in both new roof installations and reroofing projects of educational facilities. Structural versus non-structural standing-seam roofs are described as are the types of insulation that can be added and roof finishes used. (GR)

40 CFR 141.511 - What is required of new finished water reservoirs?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 23 2014-07-01 2014-07-01 false What is required of new finished water reservoirs? 141.511 Section 141.511 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Enhanced Filtration and Disinfection-Systems Serving Fewer Than 10,000...

Method of making metal matrix composites reinforced with ceramic particulates

DOEpatents

Cornie, James A.; Kattamis, Theodoulos; Chambers, Brent V.; Bond, Bruce E.; Varela, Raul H.

1989-01-01

Composite materials and methods for making such materials are disclosed in which dispersed ceramic particles are at chemical equilibrium with a base metal matrix, thereby permitting such materials to be remelted and subsequently cast or otherwise processed to form net weight parts and other finished (or semi-finished) articles while maintaining the microstructure and mechanical properties (e.g. wear resistance or hardness) of the original composite. The composite materials of the present invention are composed of ceramic particles in a base metal matrix. The ceramics are preferably carbides of titanium, zirconium, tungsten, molybdenum or other refractory metals. The base metal can be iron, nickel, cobalt, chromium or other high temperature metal and alloys thereof. For ferrous matrices, alloys suitable for use as the base metal include cast iron, carbon steels, stainless steels and iron-based superalloys.

Method of making metal matrix composites reinforced with ceramic particulates

DOEpatents

Cornie, J.A.; Kattamis, T.; Chambers, B.V.; Bond, B.E.; Varela, R.H.

1989-08-01

Composite materials and methods for making such materials are disclosed in which dispersed ceramic particles are at chemical equilibrium with a base metal matrix, thereby permitting such materials to be remelted and subsequently cast or otherwise processed to form net weight parts and other finished (or semi-finished) articles while maintaining the microstructure and mechanical properties (e.g. wear resistance or hardness) of the original composite. The composite materials of the present invention are composed of ceramic particles in a base metal matrix. The ceramics are preferably carbides of titanium, zirconium, tungsten, molybdenum or other refractory metals. The base metal can be iron, nickel, cobalt, chromium or other high temperature metal and alloys thereof. For ferrous matrices, alloys suitable for use as the base metal include cast iron, carbon steels, stainless steels and iron-based superalloys. 2 figs.

Finishing Well

NASA Astrophysics Data System (ADS)

Riendeau, Diane

2011-05-01

As we finish this publishing cycle, I'd like to thank all the readers who sent in video clips. If you have a YouTube clip that you use in class, please send the link and a brief description to driendeau@dist113.org.

Best of both worlds : clear exterior finishes : in search of finishes that protect wood without hiding its natural beauty

Treesearch

Tom Daniels; Marc Hirsch; Ken McClelland; Alan Ross; Sam Williams

2000-01-01

In recent years, a number of clear wood finishes have been developed that protect wood while accentuating its natural beauty. The focus of this publication is on those finishes having little visible pigment. In some cases, the pigments are included but are finely ground to create a coating that is transparent to visible light. Most natural clear wood finishes are...

Numerical simulation of the induction heating of hybrid semi-finished materials into the semi-solid state

NASA Astrophysics Data System (ADS)

Seyboldt, Christoph; Liewald, Mathias

2017-10-01

Current research activities at the Institute for Metal Forming Technology (IFU) of the University of Stuttgart are focusing on the manufacturing of hybrid components using semi-solid forming strategies. As part of the research project "Hybrid interaction during and after thixoforging of multi-material systems", which is founded by the German Research Foundation (DFG), a thixoforging process for producing hybrid components with cohesive metal-to-metal connections is developed. In this context, this paper deals with the numerical simulation of the inductive heating process of hybrid semi-finished materials, consisting of two different aluminium alloys. By reason of the skin effect that leads to inhomogeneous temperature distributions during inductive heating processes, the aluminium alloy with the higher melting point is thereby assembled in the outer side and the alloy with the lower melting point is assembled in the core of the semi-finished material. In this way, the graded heat distribution can be adapted to the used materialś flow properties that are heavily heat dependent. Without this graded heat distribution a proper forming process in the semi-solid state will not be possible. For numerically modelling the inductive heating system of the institute, a coupling of the magnetostatic and the thermal solver was realized by using Ansys Workbench. While the electromagnetic field and its associated heat production rate were solved in a frequency domain, the temperature development was solved in the time based domain. The numerical analysis showed that because of the high thermal conductivity of the aluminium, which leads to a rapid temperature equalization in the semi-finished material, the heating process has to be fast and with a high frequency for produce most heat in the outer region of the material. Finally, the obtained numerical results were validated with experimental heating tests.

FIELD TESTING AND EVALUATION OF ZERPOL® AT PIONEER METAL FINISHING

EPA Science Inventory

The project examines the Zerpol® process. The Zerpol® process, as used in metal plating operations, captures all aqueous effluent from the manufacturing operations, conditions the effluent to remove any metal or cyanide that may be present, and permits the reuse of the ...

Signature Peptide-Enabled Metagenomics (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)

ScienceCinema

McMahon, Ben

2018-01-11

Ben McMahon of Los Alamos National Laboratory (LANL) presents "Signature Peptide-Enabled Metagenomics" at the 7th Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting held in June, 2012 in Santa Fe, NM.

Signature Peptide-Enabled Metagenomics (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)

DOE Office of Scientific and Technical Information (OSTI.GOV)

McMahon, Ben

2012-06-01

Ben McMahon of Los Alamos National Laboratory (LANL) presents "Signature Peptide-Enabled Metagenomics" at the 7th Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting held in June, 2012 in Santa Fe, NM.

Deterministic magnetorheological finishing of optical aspheric mirrors

NASA Astrophysics Data System (ADS)

Song, Ci; Dai, Yifan; Peng, Xiaoqiang; Li, Shengyi; Shi, Feng

2009-05-01

A new method magnetorheological finishing (MRF) used for deterministical finishing of optical aspheric mirrors is applied to overcome some disadvantages including low finishing efficiency, long iterative time and unstable convergence in the process of conventional polishing. Based on the introduction of the basic principle of MRF, the key techniques to implement deterministical MRF are also discussed. To demonstrate it, a 200 mm diameter K9 class concave asphere with a vertex radius of 640mm was figured on MRF polish tool developed by ourselves. Through one process about two hours, the surface accuracy peak-to-valley (PV) is improved from initial 0.216λ to final 0.179λ and root-mean-square (RMS) is improved from 0.027λ to 0.017λ (λ = 0.6328um ). High-precision and high-efficiency convergence of optical aspheric surface error shows that MRF is an advanced optical manufacturing method that owns high convergence ratio of surface figure, high precision of optical surfacing, stabile and controllable finishing process. Therefore, utilizing MRF to finish optical aspheric mirrors determinately is credible and stabile; its advantages can be also used for finishing optical elements on varieties of types such as plane mirrors and spherical mirrors.

The Effect of Various Finish Line Configurations on the Marginal Seal and Occlusal Discrepancy of Cast Full Crowns After Cementation - An In-vitro Study

PubMed Central

Nemane, Vaishali; Meshram, Suresh

2015-01-01

Background The marginal fit of crowns is of clinical importance. It is found that marginal and occlusal discrepancies are commonly increased following cementation. The resistance of cementing materials is a factor that prevents cast restorations from being correctly seated. Different finish lines behave differently in facilitating the escape of the cement. When the escape path of the cement decreases, the crown fails to seat further. Materials and Methods This study was planned with an aim to evaluate the effect of various finish lines on the marginal seal and occlusal seat of full crown preparations. Six stainless steel metal dies were machined to simulate molar crown preparations. The diameter was 10 mm and height was 6mm. The occlusal surface was kept flat and a small circular dimple was machined for reorientation of the wax pattern and metal copings, margins of various designs were machined accurately. The margins prepared were Group A- 900C shoulder, Group B- Rounded shoulder, Group C- 45 degree sloped shoulder, Group D- Chamfer, Group E- Long chamfer, Group F- Feather edge. Full cast metal crowns of base metal alloy were fabricated over the metal dies. Zinc phosphate luting cement was used for the cementation. After twenty four hours, the cemented crown and die assembly were embedded in clear acrylic resin so as to hold the assembly together while sectioning. Twenty four hours later, all the samples were sectioned sagitally. The sectioned halves were focused under a stereomicroscope and the cement spaces were measured to the nearest micron. The cement thickness was measured at two points on the occlusal surface and one at each margin. Results Significant differences were observed in the occlusal seat and marginal seal of all the finish line configurations. The rounded shoulder had the best occlusal seat, followed by 900C shoulder. The occlusal seat and marginal seal afforded by the shoulder finish lines were similar whereas there was a vast difference in the

Optical Microscopy Techniques to Inspect for Metallic Whiskers

NASA Technical Reports Server (NTRS)

Brusse, Jay A.

2006-01-01

Metal surface finishes of tin, zinc and cadmium are often applied to electronic components, mechanical hardware and other structures. These finishes sometimes unpredictably may form metal whiskers over periods that can take from hours to months or even many years. The metal whiskers are crystalline structures commonly having uniform cross sectional area along their entire length. Typical whisker dimensions are nominally on the order of only a few microns (um) across while their lengths can extend from a few microns to several millimeters. Metal whiskers pose a reliability hazard to electronic systems primarily as an electrical shorting hazard. The extremely narrow dimensions of metal whiskers can make observation with optical techniques very challenging. The videos herein were compiled to demonstrate the complexities associated with optical microscope inspection of electronic and mechanical components and assemblies for the presence or absence of metal whiskers. The importance of magnification, light source and angle of illumination play critical roles in being able to detect metal whiskers when present. Furthermore, it is demonstrated how improper techniques can easily obscure detection. It is hoped that these videos will improve the probability of detecting metal whiskers with optical inspection techniques.

Influence of melting and casting methods and finish line design on the marginal discrepancy of nickel-chromium-titanium alloy crowns.

PubMed

Cogolludo, Pablo G; Suarez, María J; Peláez, Jesús; Lozano, José F L

2010-01-01

The aim of this study was to analyze the influence of melting and casting procedures and the cervical finish line design on the marginal fit of nickel-chromium-titanium alloy crowns. Sixty standardized specimens were prepared to receive metal-ceramic crowns and were divided into two groups according to the cervical finish line: chamfer or rounded shoulder. Three melting and casting procedures were analyzed: (1) induction-centrifuge (IC), (2) gas oxygen torch-centrifuge (TC), and (3) induction-vacuum/pressure (IP). The marginal fit was measured with an image analysis system. Significant differences (P =.005) were observed among the groups, with TC showing the lowest discrepancies (45.87 μm). No significant differences were observed between the two finish lines. The accuracy of fit achieved for the groups analyzed may be regarded as within the range of clinical acceptance.

Finishability of CCA pressure-treated wood

Treesearch

Alan Ross; Richard Carlson; William Feist; Steven Bussjaeger

2000-01-01

Thus, a need arose for the development of surface finishes for CCA-treated wood that could address the special requirements of this substrate and provide protection against the ravages of water, sunlight, mildew, and other aspects of weathering and wear. Initially, this need was not addressed, most wood preserving companies had little expertise in surface finishes and...

[Exposure to metals in dental laboratories].

PubMed

Apostoli, P; Ferioli, A; Crippa, M; Redaelli, P; Braga Marcazzan, G; Alessio, L

1988-11-01

Dental care includes handling of different types of metal alloys usually classified as "noble" and "base" in relation to the presence or absence of either gold or other precious metals. It must be born in mind that exposure to metals in this activities is due not only to those metals present in the alloys but also to those contained in the other materials used during the processes of casting and finishing. The most important metals are the following: Al, Be, Cd, Cr, Co, Cu, Au, In, Hg, Mo, Ni, Pd, Pt, Si, Ag, Sn, Ti, W, Zn. In this paper we investigated the environmental exposure to metals in dental laboratories studying the environmental air concentration of metals in casting and finishing processes estimating the "quality" of the elements present by Particle Induces X-ray Emission (PIXE) and the "quantity" of the elements by electro thermic atomic absorption spectrophotometry (ET-AAS) and the concentration of the main metals in the blood and in the urine of exposed technicians by ET-AAS. These analyses permitted to detect all the metals present in the work environment and to quantify their concentration, which always resulted to be low (except some metals during short time operations). The biological monitoring revealed the existence of moderate absorption of these metals in the exposed workers but it is not possible for us to affirm if this phenomenon represents a real risk for the health of the technicians. Hence further epidemiological and health surveillance investigations are needed to verify morbidity and mortality of the subjects employed in this activity.

Finishes for Metals. Paintability of Galvanized Steel, Corrosion Resistance of Metallized Coatings.

ERIC Educational Resources Information Center

Building Research Inst., Inc., Washington, DC.

Two papers are presented. The first, "Report of the AISI Research Project on the Paintability of Galvanized Steel," was a project aimed at determining optimum procedures for painting bright-spangled galvanized sheet steel products using three classes of trade sales paints--metallic zinc-dust, portland cement-in-oil, and water base emulsion paints.…

NCMS PWB Surface Finishes Team project summary

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kokas, J.; DeSantis, C.; Wenger, G.

1996-04-01

The NCMS PWB Surface Finishes Consortium is just about at the end of the five year program. Dozens of projects related to surface finishes and PWB solder-ability were performed by the team throughout the program, and many of them are listed in this paper. They are listed with a cross reference to where and when a technical paper was presented describing the results of the research. However, due to time and space constraints, this paper can summarize the details of only three of the major research projects accomplished by the team. The first project described is an ``Evaluation of PWBmore » Surface Finishes.`` It describes the solderability, reliability, and wire bondability of numerous surface finishes. The second project outlined is an ``Evaluation of PWB Solderability Test Methods.`` The third project outlined is the ``Development and Evaluation of Organic Solderability Preservatives.``« less

Characterization of M40J Desized and Finished Fibers

NASA Technical Reports Server (NTRS)

Allred, Ronald E.; Gosau, Jan-M.; Shin, E. Eugene; McCorkle, Linda; O'Malley, Michelle; Sutter, James K.; Wheeler, Don

1990-01-01

A viewgraph presentation on desized and finished M40J carbon fibers shown. The topics include: 1) Program Goals and Prior Year Results Summary; 2) Continuous Desizing and Finishing System Development; 3) Characterizzation of Desized and Finished M40J Carbon Fibers and 4) Conclusions and Future Work.

27 CFR 19.601 - Finished products records.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2013-04-01 2013-04-01 false Finished products records..., DEPARTMENT OF THE TREASURY ALCOHOL DISTILLED SPIRITS PLANTS Records and Reports Processing Records § 19.601 Finished products records. (a) Bottling and packaging. A proprietor must maintain daily transaction records...

27 CFR 19.601 - Finished products records.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2012-04-01 2012-04-01 false Finished products records..., DEPARTMENT OF THE TREASURY LIQUORS DISTILLED SPIRITS PLANTS Records and Reports Processing Records § 19.601 Finished products records. (a) Bottling and packaging. A proprietor must maintain daily transaction records...

27 CFR 19.601 - Finished products records.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2014-04-01 2014-04-01 false Finished products records..., DEPARTMENT OF THE TREASURY ALCOHOL DISTILLED SPIRITS PLANTS Records and Reports Processing Records § 19.601 Finished products records. (a) Bottling and packaging. A proprietor must maintain daily transaction records...

40 CFR 141.510 - Is my system subject to the new finished water reservoir requirements?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 23 2014-07-01 2014-07-01 false Is my system subject to the new finished water reservoir requirements? 141.510 Section 141.510 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Enhanced Filtration and Disinfection-Systems Servin...

Finishing procedures in orthodontic-surgical cases.

PubMed

Brunel, Jean-Michel

2015-09-01

To ensure optimal results, we must do our utmost to achieve targets based on order, symmetry and precision, our ultimate aim being to strive towards the desired harmony, planned contrast and exact proportions. Orthodontic-surgical treatments require specific finishing procedures, which most often call for multidisciplinary, or even transdisciplinary, collaboration. Finishing will involve the dental arches just as much as the orofacial environment. Above all, treatment of this kind demands a highly targeted approach in combination with well-defined and perfectly executed techniques. To finish a case satisfactorily, reasonable targets should be aimed for to ensure they are achieved. One must be ambitious and yet wise. A tight alliance of surgeon and orthodontist will nurture convincing and achievable projects and good, lifelong outcomes. Following the consolidation phase, roughly 4 to 6 weeks post-surgery, we can initiate the final orthodontic treatment, which, in effect, constitutes a mini-treatment in its own right. "Details make perfection, but perfection is not a detail" (Leonardo Da Vinci). "A lucid mind is the ante-chamber of intelligence" (Léo Ferré). In the order of life, every form of unity is always unique, and if each of us is unique, it is because everyone else is too. Ambition, wisdom, lucidity and efficiency will guarantee a successful result, the successful result. We must not be mere observers of our treatments, but the architect, project manager and site foreman at one and the same time. One could talk ad infinitum about finishing orthodontic-surgical cases because everything else leads up to the case-finishing and even the fullest description could never be exhaustive. Copyright © 2015 CEO. Published by Elsevier Masson SAS. All rights reserved.

Stiffness management of sheet metal parts using laser metal deposition

NASA Astrophysics Data System (ADS)

Bambach, Markus; Sviridov, Alexander; Weisheit, Andreas

2017-10-01

Tailored blanks are established solutions for the production of load-adapted sheet metal components. In the course of the individualization of production, such semi-finished products are gaining importance. In addition to tailored welded blanks and tailored rolled blanks, patchwork blanks have been developed which allow a local increase in sheet thickness by welding, gluing or soldering patches onto sheet metal blanks. Patchwork blanks, however, have several limitations, on the one hand, the limited freedom of design in the production of patchwork blanks and, on the other hand, the fact that there is no optimum material bonding with the substrate. The increasing production of derivative and special vehicles on the basis of standard vehicles, prototype production and the functionalization of components require solutions with which semi-finished products and sheet metal components can be provided flexibly with local thickenings or functional elements with a firm metallurgical bond to the substrate. An alternative to tailored and patchwork blanks is, therefore, a free-form reinforcement applied by additive manufacturing via laser metal deposition (LMD). By combining metal forming and additive manufacturing, stiffness can be adapted to the loads based on standard components in a material-efficient manner and without the need to redesign the forming tools. This paper details a study of the potential of stiffness management by LMD using a demonstrator part. Sizing optimization is performed and part distortion is taken into account to find an optimal design for the cladding. A maximum stiffness increase of 167% is feasible with only 4.7% additional mass. Avoiding part distortion leads to a pareto-optimal design which achieves 95% more stiffness with 6% added mass.

Surface integrity and corrosion performance of biomedical magnesium-calcium alloy processed by hybrid dry cutting-finish burnishing.

PubMed

Salahshoor, M; Li, C; Liu, Z Y; Fang, X Y; Guo, Y B

2018-02-01

Biodegradable magnesium-calcium (MgCa) alloy is a very attractive orthopedic biomaterial compared to permanent metallic alloys. However, the critical issue is that MgCa alloy corrodes too fast in the human organism. Compared to dry cutting, the synergistic dry cutting-finish burnishing can significantly improve corrosion performance of MgCa0.8 (wt%) alloy by producing a superior surface integrity including good surface finish, high compressive hook-shaped residual stress profile, extended strain hardening in subsurface, and little change of grain size. A FEA model was developed to understand the plastic deformation of MgCa materials during burnishing process. The measured polarization curves, surface micrographs, and element distributions of the corroded surfaces by burnishing show an increasing and uniform corrosion resistance to simulated body fluid. Copyright © 2017 Elsevier Ltd. All rights reserved.

16 CFR 1508.7 - Construction and finishing.

Code of Federal Regulations, 2010 CFR

2010-01-01

... REGULATIONS REQUIREMENTS FOR FULL-SIZE BABY CRIBS § 1508.7 Construction and finishing. (a) All wood surfaces shall be smooth and free from splinters. (b) All wood parts shall be free from splits, cracks, or other... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Construction and finishing. 1508.7 Section...

16 CFR 1509.8 - Construction and finishing.

Code of Federal Regulations, 2010 CFR

2010-01-01

... REGULATIONS REQUIREMENTS FOR NON-FULL-SIZE BABY CRIBS § 1509.8 Construction and finishing. (a) All wood surfaces of non-full-size baby cribs shall be smooth and free from splinters. (b) All wood parts of non... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Construction and finishing. 1509.8 Section...

Process of preparing metal parts to be heated by means of infrared radiance

DOEpatents

Mayer, Howard Robinson [Cincinnati, OH; Blue, Craig A [Knoxville, TN

2009-06-09

A method for preparing metal for heating by infrared radiance to enable uniform and consistent heating. The surface of one or more metal parts, such as aluminum or aluminum alloy parts, is treated to alter the surface finish to affect the reflectivity of the surface. The surface reflectivity is evaluated, such as by taking measurements at one or more points on the surface, to determine if a desired reflectivity has been achieved. The treating and measuring are performed until the measuring indicates that the desired reflectivity has been achieved. Once the treating has altered the surface finish to achieve the desired reflectivity, the metal part may then be exposed to infrared radiance to heat the metal part to a desired temperature, and that heating will be substantially consistent throughout by virtue of the desired reflectivity.

Role of alginate in antibacterial finishing of textiles.

PubMed

Li, Jiwei; He, Jinmei; Huang, Yudong

2017-01-01

Antibacterial finishing of textiles has been introduced as a necessary process for various purposes especially creating a fabric with antimicrobial activities. Currently, the textile industry continues to look for textiles antimicrobial finishing process based on sustainable biopolymers from the viewpoints of environmental friendliness, industrialization, and economic concerns. This paper reviews the role of alginate, a sustainable biopolymer, in the development of antimicrobial textiles, including both basic physicochemical properties of alginate such as preparation, chemical structure, molecular weight, solubility, viscosity, and sol-gel transformation property. Then different processing routes (e.g. nanocomposite coating, ionic cross-linking coating, and Layer-by-Layer coating) for the antibacterial finishing of textiles by using alginate are revised in some detail. The achievements in this area have increased our knowledge of alginate application in the field of textile industry and promoted the development of green textile finishing. Copyright © 2016 Elsevier B.V. All rights reserved.

The effect of porcelain firing and type of finish line on the marginal fit of zirconia copings.

PubMed

Vojdani, Mahroo; Safari, Anahita; Mohaghegh, Mina; Pardis, Soheil; Mahdavi, Farideh

2015-06-01

Although all-ceramic restorations are broadly used, there is a lack of information concerning how their fit is affected by fabrication procedure and marginal configuration. The purpose of this study was to evaluate the marginal fit of zirconia CAD/CAM ceramic crowns before and after porcelain firing. The influence of finish line configuration on the marginal fit was also evaluated. Twenty standardized zirconia CAD/CAM copings were fabricated for chamfer and shoulder finish line designs (n=10). The marginal fit of specimens was measured on 18 points, marked on the master metal die by using a digital microscope. After the crowns were finalized by porcelain veneering, the measurements of marginal fit were performed again. The means and standard deviations were calculated and data were analyzed using student's t-test and paired t-test (α=0.05). There were significant differences between marginal fit of chamfer and shoulder finish line groups before and after porcelain firing (p= 0.014 and p= 0.000, respectively). The marginal gap of copings with shoulder finish line was significantly smaller than those with chamfer configuration (p= 0.000), but there were no significant differences between the two marginal designs, after porcelain firing (p= 0.341). Porcelain veneering was found to have a statistically significant influence on the marginal fit of zirconia CAD/CAM crowns. Both margin configurations showed marginal gaps that were within a reported clinically acceptable range of marginal discrepancy.

[Research and analysis to Shui nationality medicine treatment orthopedics & traumatology].

PubMed

Hu, Jian-Shan; Li, Pu; Yang, Yong; Chen, Xin-Chun; Lin, Li

2013-05-01

To investigated Shui nationality folk medicine's awareness to orthopedics & traumatology, the history of orthopedics & traumatology treatment, Shui nationality folk doctors' practicing medicine, heritage, diagnosis and treatment methods and tools, etc, through investigated drug resources category and distribution characteristics of Shui nationality medicine to orthopedics & traumatology treatment, explored and finished Shui nationality medicine orthopedics & traumatology treatment theoretical system. After more than 5 years' exploration and finishing, preliminarily formed the theoretical system framework and medicine application characteristics of Shui nationality medicine treating orthopedics & traumatology. Shui nationality medicine treatment orthopedics & traumatology has distinctive national style, and worthy to further exploration and research.

Drywall Finishing Manual.

ERIC Educational Resources Information Center

Lengert, Gerald

This manual, a self-study guide for apprentices in the drywall finishing trade in British Columbia, attempts to establish standards for the trade. It tells how to produce a properly taped and filled drywall surface and describes what that surface should look like. The standards emphasize quality work that can be realistically achieved on the job.…

40 CFR 63.1347 - Standards for raw and finish mills.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Standards for raw and finish mills. 63... and Operating Limits § 63.1347 Standards for raw and finish mills. The owner or operator of each new or existing raw mill or finish mill at a facility which is a major source subject to the provisions...

Effect of Burnishing Parameters on Surface Finish

NASA Astrophysics Data System (ADS)

Shirsat, Uddhav; Ahuja, Basant; Dhuttargaon, Mukund

2017-08-01

Burnishing is cold working process in which hard balls are pressed against the surface, resulting in improved surface finish. The surface gets compressed and then plasticized. This is a highly finishing process which is becoming more popular. Surface quality of the product improves its aesthetic appearance. The product made up of aluminum material is subjected to burnishing process during which kerosene is used as a lubricant. In this study factors affecting burnishing process such as burnishing force, speed, feed, work piece diameter and ball diameter are considered as input parameters while surface finish is considered as an output parameter In this study, experiments are designed using 25 factorial design in order to analyze the relationship between input and output parameters. The ANOVA technique and F-test are used for further analysis.

Heavy metal concentrations in a lichen of Mt. Rainier and Olympic National Parks, Washington, USA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frenzel, R.W.; Witmer, G.W.; Starkey, E.E.

1990-01-01

It is commonly assumed that the larger National Parks in the United States are pristine places which can provide baseline environmental conditions for comparisons with more developed areas. However, recently it has been recognized that many National Pars are threatened by atmospheric pollution. Until 1985, a copper smelter at Tacoma, Washington, 50 km northwest of Mount Rainier National Park, Washington emitted 30 tons of lead annually, along with high levels of arsenic and other metals. Other nearby sources of airborne heavy metals include a coal-fired generating plant at Centralia, 80 km west of the Park, and automobiles within the Seattle-Tacomamore » metropolitan area 50-100 km to the northwest. Heavy metals are a potential threat because they may effect ecosystems by decreasing nutrient cycling rates and impairing overall productivity. The objective of this study was to test the hypothesis that an arboreal lichen (Alectoria sarmentosa) within Mt. Rainier National Park contained elevated levels of heavy metals from these sources. This lichen species was chosen because it is common throughout forested areas of the region. Olympic National Park was selected as an experimental control area because it is located on the relatively undeveloped Olympic Penisula west of Seattle-Tacoma.« less

Chemically Accelerated Vibratory Surface Finishing (CAVSF)

DTIC Science & Technology

2009-02-01

media) • End-roughness and micro structure of different C- steels • Material removal and roughness changes versus the amount of treatment solution in...surface finishing (CAVSF) Visual appearance of strip steel test pieces during the CAVSF process. 0-120 minutes = acid treatment 120-135 minutes = water... steel during the super-finishing process 0 50 100 150 200 250 300 350 0 50 100 150 200 250 Time minutes R e m o v e d m a t e r i a l m i c r

Legume finishing provides beef with positive human dietary fatty acid ratios and consumer preference comparable with grain-finished beef.

PubMed

Chail, A; Legako, J F; Pitcher, L R; Griggs, T C; Ward, R E; Martini, S; MacAdam, J W

2016-05-01

Consumer liking, proximate composition, pH, Warner-Bratzler shear force, fatty acid composition, and volatile compounds were determined from the LM (longissimus thoracis) of cattle ( = 6 per diet) finished on conventional feedlot (USUGrain), legume, and grass forage diets. Forage diets included a condensed tannin-containing perennial legume, birdsfoot trefoil (; USUBFT), and a grass, meadow brome ( Rehmann; USUGrass). Moreover, representative retail forage (USDA Certified Organic Grass-fed [OrgGrass]) and conventional beef (USDA Choice, Grain-fed; ChGrain) were investigated ( = 6 per retail type). The ChGrain had the greatest ( < 0.05) intramuscular fat (IMF) percentage followed by USUGrain, the IMF percentage of which was greater ( < 0.05) than that of USUGrass and OrgGrass. The IMF content of USUBFT was similar ( > 0.05) to that of both USUGrain and USUGrass. Both grain-finished beef treatments were rated greater ( < 0.05) for flavor, tenderness, fattiness, juiciness, and overall liking compared with USUGrass and OrgGrass. Consumer liking of USUBFT beef tenderness, fattiness, and overall liking were comparable ( > 0.05) with that of USUGrain and ChGrain. Flavor liking was rated greatest ( < 0.05) for USUGrain and ChGrain, and that of USUBFT was intermediate ( > 0.05) to those of ChGrain, USUGrass, and OrgGrass. Cumulative SFA and MUFA concentrations were greatest ( < 0.05) in ChGrain and USUGrain, whereas USUGrass and OrgGrass had lower ( < 0.05) concentrations. Concentrations of cumulative SFA and MUFA in USUBFT were intermediate and similar ( > 0.05) to those of USUGrain and USUGrass. Each forage-finished beef treatment, USUGrass, OrgGrass, and USUBFT, had lower ( < 0.001) ratios of -6:-3 fatty acids. Hexanal was the most numerically abundant volatile compound. The concentration of hexanal increased with increasing concentrations of total PUFA. Among all the lipid degradation products (aldehydes, alcohols, furans, carboxylic acids, and ketones) measured in this

National Trends in Trace Metals Concentrations in Ambient Particulate Matter

NASA Astrophysics Data System (ADS)

McCarthy, M. C.; Hafner, H. R.; Charrier, J. G.

2007-12-01

Ambient measurements of trace metals identified as hazardous air pollutants (HAPs, air toxics) collected in the United States from 1990 to 2006 were analyzed for long-term trends. Trace metals analyzed include lead, manganese, arsenic, chromium, nickel, cadmium, and selenium. Visual and statistical analyses were used to identify and quantify temporal variations in air toxics at national and regional levels. Trend periods were required to be at least five years. Lead particles decreased in concentration at most monitoring sites, but trends in other metals were not consistent over time or spatially. In addition, routine ambient monitoring methods had method detection limits (MDLs) too high to adequately measure concentrations for trends analysis. Differences between measurement methods at urban and rural sites also confound trends analyses. Improvements in MDLs, and a better understanding of comparability between networks, are needed to better quantify trends in trace metal concentrations in the future.

A national level assessment of metal contamination in bats.

PubMed

Hernout, Béatrice V; Arnold, Kathryn E; McClean, Colin J; Walls, Michael; Baxter, Malcolm; Boxall, Alistair B A

2016-07-01

Many populations of bat species across the globe are declining, with chemical contamination one of many potential stressors implicated in these demographic changes. Metals still contaminate a wide range of habitats, but the risks to bats remain poorly understood. This study is the first to present a national scale assessment of toxic metal (Cd, Pb) and essential trace metal (Cu, Zn) concentrations in bats. Metal concentrations in tissues (kidneys, liver, stomach -stomach content, bones and fur) were measured in 193 Pipistrellus sp. in England and Wales using ICP-MS, and compared to critical toxic concentrations for small mammals. The concentrations of metals determined in bat tissues were generally lower than those reported elsewhere. Strong positive associations were found between concentrations in tissues for a given metal (liver and kidneys for Cd, Cu and Pb; stomach and fur and fur and bones for Pb), suggesting recent as well as long term exposure to these contaminants. In addition, positive correlations between concentrations of different metals in the same tissues (Cd and Zn, Cu and Zn, Cd and Pb, Pb and Zn) suggest a co-exposure of metals to bats. Approximately 21% of the bats sampled contained residues of at least one metal at concentrations high enough to elicit toxic effects (associated with kidney damage), or to be above the upper level measured in other mammal species. Pb was found to pose the greatest risk (with 7-11% of the bats containing concentrations of toxicological concern), followed by Cu (4-9%), Zn (0.5-5.2%) and Cd (0%). Our data suggest that leaching of metals into our storage matrix, formaldehyde, may have occurred, especially for Cu. The overall findings suggest that metal contamination is an environmental stressor affecting bat populations, and that further research is needed into the direct links between metal contamination and bat population declines worldwide. Copyright © 2016 Elsevier Ltd. All rights reserved.

Clear exterior finishes : finding the balance between aesthetics and durability

Treesearch

Tom Daniel; Marc S. Hirsch; Ken McClelland; Alan S. Ross; R. Sam Williams

2004-01-01

Consumers can easily be confused by the abundance of choices to make when selecting a clear wood finish. There are many types of clear finishes with different characteristics and product claims. This article is designed to help consumers sort out the different finishes and effectively choose which product would be best for their purpose. First, we cover the causes and...

Evaluation of several finishes on severely weathered wood

Treesearch

R. Sam Williams; Peter Sotos; William Feist

1999-01-01

Alkyd-, oil-modified-latex-, and latex-based finishes were applied to severely weathered western redcedar and redwood boards that did not have any surface treatment to ameliorate the weathered surface prior to painting. Six finishes were evaluated annually for 11 years for cracking, flaking, erosion, mildew growth, discoloration, and general appearance. Low-solids-...

Mechanical Reliability of the Epoxy Sn-58wt.%Bi Solder Joints with Different Surface Finishes Under Thermal Shock

NASA Astrophysics Data System (ADS)

Sung, Yong-Gue; Myung, Woo-Ram; Jeong, Haksan; Ko, Min-Kwan; Moon, Jeonghoon; Jung, Seung-Boo

2018-04-01

The effect of thermal shock on the mechanical reliability of epoxy Sn-58wt.%Bi composite (epoxy Sn-58wt.%Bi) solder joints was investigated with different surface-finished substrates. Sn-58wt.%Bi-based solder has been considered as a promising candidate for low-temperature solder among various lead-free solders. However, Sn-58wt.%Bi solder joints can be easily broken under impact conditions such as mechanical shock, drop tests, and bending tests because of their poor ductility. Therefore, previous researchers have tried to improve the mechanical property of Sn-58wt.%Bi solder by additional elements and mixtures of metal powder and epoxy resin. Epoxy Sn-58wt.%Bi solder paste was fabricated by mixing epoxy resin and Sn-58wt.%Bi solder powder to enhance the mechanical reliability of Sn-58wt.%Bi solder joints. The epoxy Sn-58wt.%Bi solder paste was screen-printed onto various printed circuit board surfaces finished with organic solder preservatives (OSP), electroless nickel immersion gold (ENIG), and electroless nickel electroless palladium immersion gold (ENEPIG). The test components were prepared by a reflow process at a peak temperature of 190°C. The thermal shock test was carried out under the temperature range of - 40 to 125°C to evaluate the reliability of Sn-58wt.%Bi and epoxy Sn-58wt.%Bi solder joints. The OSP-finished sample showed a relatively higher mechanical property than those of ENIG and ENEPIG after thermal shock. The average number of cycles for epoxy Sn-58wt.%Bi solder with the OSP surface finish were 6 times higher than that for Sn-58wt.%Bi solder with the same finish. The microstructures of the solder joints were investigated by scanning electron microscopy, and the composition of the intermetallic compound (IMC) layer was analyzed by using energy dispersive spectrometry. Cu6Sn5 IMC was formed by the reaction between Sn-58wt.%Bi solder and a OSP surface-finished Cu after the reflow process. Ni3Sn4 IMC and (Ni, Pd)3Sn4 IMC were formed at the solder

Mechanical Reliability of the Epoxy Sn-58wt.%Bi Solder Joints with Different Surface Finishes Under Thermal Shock

NASA Astrophysics Data System (ADS)

Sung, Yong-Gue; Myung, Woo-Ram; Jeong, Haksan; Ko, Min-Kwan; Moon, Jeonghoon; Jung, Seung-Boo

2018-07-01

The effect of thermal shock on the mechanical reliability of epoxy Sn-58wt.%Bi composite (epoxy Sn-58wt.%Bi) solder joints was investigated with different surface-finished substrates. Sn-58wt.%Bi-based solder has been considered as a promising candidate for low-temperature solder among various lead-free solders. However, Sn-58wt.%Bi solder joints can be easily broken under impact conditions such as mechanical shock, drop tests, and bending tests because of their poor ductility. Therefore, previous researchers have tried to improve the mechanical property of Sn-58wt.%Bi solder by additional elements and mixtures of metal powder and epoxy resin. Epoxy Sn-58wt.%Bi solder paste was fabricated by mixing epoxy resin and Sn-58wt.%Bi solder powder to enhance the mechanical reliability of Sn-58wt.%Bi solder joints. The epoxy Sn-58wt.%Bi solder paste was screen-printed onto various printed circuit board surfaces finished with organic solder preservatives (OSP), electroless nickel immersion gold (ENIG), and electroless nickel electroless palladium immersion gold (ENEPIG). The test components were prepared by a reflow process at a peak temperature of 190°C. The thermal shock test was carried out under the temperature range of - 40 to 125°C to evaluate the reliability of Sn-58wt.%Bi and epoxy Sn-58wt.%Bi solder joints. The OSP-finished sample showed a relatively higher mechanical property than those of ENIG and ENEPIG after thermal shock. The average number of cycles for epoxy Sn-58wt.%Bi solder with the OSP surface finish were 6 times higher than that for Sn-58wt.%Bi solder with the same finish. The microstructures of the solder joints were investigated by scanning electron microscopy, and the composition of the intermetallic compound (IMC) layer was analyzed by using energy dispersive spectrometry. Cu6Sn5 IMC was formed by the reaction between Sn-58wt.%Bi solder and a OSP surface-finished Cu after the reflow process. Ni3Sn4 IMC and (Ni, Pd)3Sn4 IMC were formed at the solder

The Effect of Porcelain Firing and Type of Finish Line on the Marginal Fit of Zirconia Copings

PubMed Central

Vojdani, Mahroo; Safari, Anahita; Mohaghegh, Mina; Pardis, Soheil; Mahdavi, Farideh

2015-01-01

Statement of the Problem Although all-ceramic restorations are broadly used, there is a lack of information concerning how their fit is affected by fabrication procedure and marginal configuration. Purpose The purpose of this study was to evaluate the marginal fit of zirconia CAD/CAM ceramic crowns before and after porcelain firing. The influence of finish line configuration on the marginal fit was also evaluated. Materials and Method Twenty standardized zirconia CAD/CAM copings were fabricated for chamfer and shoulder finish line designs (n=10). The marginal fit of specimens was measured on 18 points, marked on the master metal die by using a digital microscope. After the crowns were finalized by porcelain veneering, the measurements of marginal fit were performed again. The means and standard deviations were calculated and data were analyzed using student’s t-test and paired t-test (α=0.05). Results There were significant differences between marginal fit of chamfer and shoulder finish line groups before and after porcelain firing (p= 0.014 and p= 0.000, respectively). The marginal gap of copings with shoulder finish line was significantly smaller than those with chamfer configuration (p= 0.000), but there were no significant differences between the two marginal designs, after porcelain firing (p= 0.341). Conclusion Porcelain veneering was found to have a statistically significant influence on the marginal fit of zirconia CAD/CAM crowns. Both margin configurations showed marginal gaps that were within a reported clinically acceptable range of marginal discrepancy. PMID:26046107

[The statistical analysis for the use of the 55,787 finished resin teeth].

PubMed

Wu, Shu-hong; Yu, Hai-yang; Wang, Lu; Xu, Ling; Xiao, Zhi-li

2010-08-01

To analyze the use situation of finished resin teeth for the different location, and to provide reference for manufacturers of finished resin teeth and all the buyers. To analyze the use situation of finished resin teeth in the Dental Laboratory of the Affiliated Hospital of Stomatology of Chongqing Medical University from January 2006 to December 2008 by using statistic methods. During the use of 55,787 finished resin teeth, the study found some rules. (1) The top use of finished resin teeth was D6 with the percentage of 5.31%, and the lowest use of finished resin teeth was D3 with the percentage of 1.94%. (2) Except the maxillary canines and the mandibular lateral incisors, there was no significant difference between the usage of other same name finished resin teeth (P > 0.05). (3) Among all finished resin teeth, the usage of section B exceeded section A, and the usage of maxillary finished resin teeth exceeded mandibular finished resin teeth (P < 0.05). (4) The use of the complete denture and single complete denture was about 1/3 of the total usage of finished resin teeth. (5) Except the use situation of complete denture and single complete denture, the frequency of simultaneously using mandibular left and right central incisors was the most with the percentage of 81.46%, for the frequency of simultaneously using maxillary left and right canines was 43.26% of the total, which was the lowest. There is significant difference in the use frequency of finished resin teeth for different location. For such reason, the manufacturers should produce finished resin teeth pro rata as well as the buyers for their purchase.

NON-POLLUTING METAL SURFACE FINISHING PRETREATMENT AND PRETREATMENT/CONVERSION COATING

EPA Science Inventory

Picklex, a proprietary formulation, is an alterantive to conventional metal surface pretreatments and is claimed not to produce waste or lower production or lower performance. A laboratory program was designed to evaluate Picklex in common, large scale, polluting surface finishin...

7 CFR 58.525 - Storage of finished product.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 3 2011-01-01 2011-01-01 false Storage of finished product. 58.525 Section 58.525... Procedures § 58.525 Storage of finished product. Cottage cheese after packaging shall be promptly stored at a... distribution and storage prior to sale the product should be maintained at a temperature of 45 °F. or lower...

7 CFR 58.525 - Storage of finished product.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 3 2013-01-01 2013-01-01 false Storage of finished product. 58.525 Section 58.525... Procedures § 58.525 Storage of finished product. Cottage cheese after packaging shall be promptly stored at a... distribution and storage prior to sale the product should be maintained at a temperature of 45 °F. or lower...

7 CFR 58.525 - Storage of finished product.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Storage of finished product. 58.525 Section 58.525... Procedures § 58.525 Storage of finished product. Cottage cheese after packaging shall be promptly stored at a... distribution and storage prior to sale the product should be maintained at a temperature of 45 °F. or lower...

Vertical marginal discrepancy of ceramic copings with different ceramic materials, finish lines, and luting agents: an in vitro evaluation.

PubMed

Quintas, Adriana Ferreira; Oliveira, Fabiano; Bottino, Marco Antonio

2004-09-01

Prosthetic restorations that fit poorly may affect periodontal health and occlusion. Studies that have evaluated the accuracy of fit of ceramic restorations before and after cementation assessed primarily intracoronal restorations. This in vitro study evaluated the effect of different finish lines, ceramic manufacturing techniques, and luting agents on the vertical discrepancy of ceramic copings. Two stainless steel molars were prepared for complete crowns with 2 different finish lines (heavy chamfer and rounded shoulder); each molar was duplicated to fabricate 90 copings. A total of 180 copings generated 18 groups (n=10 for each finish line-coping material-luting agent combination). Luting agents tested included zinc phosphate, resin-modified glass ionomer (Fuji Plus), and resin composite cements (Panavia F). A metal frame was developed on which to screw the stainless steel model and a ceramic coping; the distance (microm) between 2 predetermined points was measured before and after cementation by a profile projector under a torquing force. A 4-way ANOVA with repeated measurements was performed to assess the influence of each factor in the vertical marginal discrepancy: 3 between-coping factors (finish line-coping material-luting agent) and 1 within-coping factor (before and after cementation) (alpha=.05). Procera copings presented the lowest mean values ( P <.05) of vertical marginal discrepancy before and after cementation (25/44 microm) when compared to Empress 2 (68/110 microm) and InCeram Alumina copings (57/117 microm), regardless of any combinations among all finish lines and luting agents tested. Considering each factor separately, the ceramic manufacturing technique appeared to be the most important factor tested for the definitive vertical discrepancy of all-ceramic copings, with lower mean values for Procera copings.

Bilingual Skills Training Program. Auto Body Repair. Module 3.0: Basic Metal Repair.

ERIC Educational Resources Information Center

Northern New Mexico Community Coll., El Rito.

This module on basic metal repair is the third of four (CE 028 303-306) in the auto body repair course of a bilingual vocational training program. The course is designed to furnish theoretical and laboratory experience in welding, metal straightening, metal finishing, painting, and use of power and hand tools. Module objectives are for students to…

Effects of metal mining and milling on boundary waters of Yellowstone National Park, USA

USGS Publications Warehouse

Nimmo, D.R.; Willox, M.J.; Lafrancois, T.D.; Chapman, P.L.; Brinkman, S.F.; Greene, J.C.

1998-01-01

Aquatic resources in Soda Butte Creek within Yellowstone National Park, USA, continue to be threatened by heavy metals from historical mining and milling activities that occurred upstream of the park's boundary. This includes the residue of gold, silver, and copper ore mining and processing in the early 1900s near Cooke City, Montana, just downstream of the creek's headwaters. Toxicity tests, using surrogate test species, and analyses of metals in water, sediments, and macroinvertebrate tissue were conducted from 1993 to 1995. Chronic toxicity to test species was greater in the spring than the fall and metal concentrations were elevated in the spring with copper exceeding water quality criteria in 1995. Tests with amphipods using pore water and whole sediment from the creek and copper concentrations in the tissue of macroinvertebrates and fish also suggest that copper is the metal of concern in the watershed. In order to understand current conditions in Soda Butte Creek, heavy metals, especially copper, must be considered important factors in the aquatic and riparian ecosystems within and along the creek extending into Yellowstone National Park.

[Key content and formulation of national Chinese materia medica resources survey at county level].

PubMed

Lu, Jian-Wei; Zhang, Xiao-Bo; Li, Hai-Tao; Guo, Lan-Ping; Zhao, Run-Huai; Zhang, Ben-Gang; Sun, Li-Ying; Huang, Lu-Qi

2013-08-01

According to National Census for Water, National Population Census, National Land and Resources Survey, and work experience of experimental measures for national Chinese materia medica resources(CMMR) survey,the national CMMR survey at the county level is the key point of whole survey, that includes organization and management, field survey, sorting data three key links. Organization and management works of national CMMR survey needs to finish four key contents, there are definite goals and tasks, practicable crew, preparation directory, and security assurance. Field survey works of the national CMMR survey needs to finish five key contents, there are preparation works for field survey, the choice of the key survey area (samples), fill in the questionnaire, video data collection, specimen and other physical collection. Sorting data works of the national CMMR survey needs to finish tree key contents, there are data, specimen and census results.

Wall Finishes; Carpentry: 901895.

ERIC Educational Resources Information Center

Dade County Public Schools, Miami, FL.

The course outline is designed to provide instruction in selecting, preparing, and installing wall finishing materials. Prerequisites for the course include mastery of building construction plans, foundations and walls, and basic mathematics. Intended for use in grades 11 and 12, the course contains five blocks of study totaling 135 hours of…

Construction of a Dip Tank for Finishing Wood Siding or Decking

Treesearch

Mark Knaebe

2013-01-01

Dipping new siding or decking pieces before installation is faster than finishing after installation, and it gets finish on the backside and ends of the pieces, thereby extending their service life. This method is appropriate for any penetrating finish, such as waterrepellent preservatives or semitransparent stains. It may also be used to pre-treat siding with water-...

Purification of metal finishing waste waters with zeolites and activated carbons.

PubMed

Leinonen, H; Lehto, J

2001-02-01

Sixteen zeolites and 5 activated carbons were tested for the removal of nickel, zinc, cadmium, copper, chromium, and cobalt from waste simulants mimicking effluents produced in metal plating plants. The best performances were obtained from 4 zeolites: A, X, L, and ferrierite types and from 2 carbon types made from lignite and peat. The distribution coefficients for these sorbents were in the range of 10,000-440,000 ml/g. Column experiments showed that the most effective zeolites for Zn, Ni, Cu, and Cd were A and X type zeolites. The activated carbons, Hydrodarco 3000 and Norit Row Supra, exhibited good sorption properties for metals in aqueous solutions containing complexing agents.

Sunrayce 97 Finish Sets Records

Science.gov Websites

in Indianapolis,, Sunrayce 97 roared to a record finish in Colorado Springs. Winning the event , followed closely by the University of Waterloo, and the University of Minnesota. The event started in

Additives aided composting of green waste: effects on organic matter degradation, compost maturity, and quality of the finished compost.

PubMed

Gabhane, Jagdish; William, S P M Prince; Bidyadhar, Rajnikant; Bhilawe, Priya; Anand, Duraisamy; Vaidya, Atul N; Wate, Satish R

2012-06-01

The effect of various additives such as fly ash, phosphogypsum, jaggery, lime, and polyethylene glycol on green waste composting was investigated through assessing their influence on microbial growth, enzymatic activities, organic matter degradation, bulk density, quality of finished compost including gradation test, heavy metal analysis, etc. A perusal of results showed that addition of jaggery and polyethylene glycol were helpful to facilitate composting process as they significantly influenced the growth of microbes and cellulase activity. The quality of finished compost prepared from jaggery and polyethylene glycol added treatments were superior to other composts, wherein reduction in C/N ratio was more than 8% in jaggery treatment. All other parameters of compost quality including gradation test also favored jaggery and polyethylene glycol as the best additives for green waste composting. Copyright © 2012 Elsevier Ltd. All rights reserved.

CANVAS FINISH TO REMOVE FLOAT MARKS. View is to the ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

CANVAS FINISH TO REMOVE FLOAT MARKS. View is to the northwest of deck finishing operations - South Fork Trinity River Bridge, State Highway 299 spanning South Fork Trinity River, Salyer, Trinity County, CA

Provenance of the oil in par-fried French fries after finish frying.

PubMed

Al-Khusaibi, Mohammed; Gordon, Michael H; Lovegrove, Julie A; Niranjan, Keshavan

2012-01-01

Frozen par-fried French fries are finish-fried either by using the same type of oil used for par frying, or a different type. The nutritive quality of the final oil contained in the product depends on the relative amounts and the fatty acid (FA) composition of the oils used for par frying and finish frying. With the aim of understanding the provenance of the oil in the final product, par-fried French fries-either purchased ready or prepared in the laboratory-were finish fried in oils different from the ones used for par frying. The moisture content, oil content, and FA compositions of the par-fried and finish-fried products were experimentally determined, and the relative amounts of each of the oils present in the final product were calculated using the FAs as markers and undertaking a mass balance on each component FA. The results demonstrate that 89% to 93% of the total oil in the final product originates from the finish-frying step. The study also shows that a significant proportion of the oil absorbed during par frying is expelled from the product during finish frying. Further, the expulsion of par-frying oil was found to occur in the early stages of the finish-frying step. Experiments involving different combinations of par-frying and finish-frying oils showed that the relative proportions of the 2 oils did not depend on the individual fatty acid profiles. This study concludes that any positive health benefits of using an oil having a favorable FA profile for par frying, can potentially be lost, if the oil used for finish frying has a less favorable composition. This paper estimates the relative amounts of oil in French fries that have been fried in 2 stages-a par-frying step and a finish-frying step-which is commonly practiced in food service establishments as well as homes. The 2 key conclusions are: (1) nearly 90% of the oil content of the final product is the one used for finish frying; that is, a processor may use very good oil for par frying but if the

School Building Finishing and Economy. The School Building Economy Series, No. 6.

ERIC Educational Resources Information Center

Connecticut State Dept. of Education, Hartford.

Materials, elements, and methods of economical school construction are illustrated through explanatory outlines and accompany photographs and diagrams. Finishing elements covered include--(1) finished floorings, (2) ceilings and acoustical finishes, (3) carpentry and millwork, (4) chalkboards and tackboards, (5) toilet partitions, (6) finishing…

FINISHED CASTINGS ARE ONLY GROUND BEFORE THEY ARE SHIPPED TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

FINISHED CASTINGS ARE ONLY GROUND BEFORE THEY ARE SHIPPED TO CUSTOMERS WHO COMPLETE THE FINISHING IN THEIR OWN MACHINE SHOPS. - Southern Ductile Casting Company, Grinding & Shipping, 2217 Carolina Avenue, Bessemer, Jefferson County, AL

Orthodontic treatment outcomes obtained by application of a finishing protocol

PubMed Central

Carvajal-Flórez, Alvaro; Barbosa-Lis, Diana María; Zapata-Noreña, Oscar Arturo; Marín-Velásquez, Julissa Andrea; Afanador-Bayona, Sergio Andrés

2016-01-01

ABSTRACT Objective: To evaluate the results of a finishing protocol implemented in patients treated in the Orthodontics graduate program at Universidad de Antioquia. Evaluation was carried out by means of the criteria set by the Objective Grading System (OGS) of the American Board of Orthodontics (ABO). Methods: Cast models and panoramic radiographs of 34 patients were evaluated. The intervention group (IG) consisted of 17 patients (19.88 ± 4.4 years old) treated under a finishing protocol. This protocol included training in finishing, application of a finishing guide, brackets repositioning and patient's follow-up. Results of the IG were compared to a control group of 17 patients (21.88 ± 7.0 years old) selected by stratified randomization without finishing intervention (CG). Results: The scores for both CG and IG were 38.00 ± 9.0 and 31.41 ± 9.6 (p = 0.048), respectively. The score improved significantly in the IG group, mainly regarding marginal ridges (CG: 5.59 ± 2.2; IG: 3.65 ± 1.8) (p = 0.009) and root angulation (CG: 7.59 ± 2.8; IG: 4.88 ± 2.6) (p = 0.007). Criteria that did not improve, but had the highest scores were: alignment (CG: 6.35 ± 2.7; IG: 6.82 ± 2.8) (p = 0.62) and buccolingual inclination (CG: 3.6 ± 5.88; IG: 5.29 ± 3.9) (p = 0.65). Conclusions: Standardization and implementation of a finishing protocol contributed to improve clinical performance in the Orthodontics graduate program, as expressed by occlusal outcomes. Greater emphasis should be given on the finishing phase to achieve lower scores in the ABO grading system. PMID:27275620

A Research Communication Brief: Gluten Analysis in Beef Samples Collected Using a Rigorous, Nationally Representative Sampling Protocol Confirms That Grain-Finished Beef Is Naturally Gluten-Free.

PubMed

McNeill, Shalene H; Cifelli, Amy M; Roseland, Janet M; Belk, Keith E; Woerner, Dale R; Gehring, Kerri B; Savell, Jeffrey W; Brooks, J Chance; Thompson, Leslie D

2017-08-25

Knowing whether or not a food contains gluten is vital for the growing number of individuals with celiac disease and non-celiac gluten sensitivity. Questions have recently been raised about whether beef from conventionally-raised, grain-finished cattle may contain gluten. To date, basic principles of ruminant digestion have been cited in support of the prevailing expert opinion that beef is inherently gluten-free. For this study, gluten analysis was conducted in beef samples collected using a rigorous nationally representative sampling protocol to determine whether gluten was present. The findings of our research uphold the understanding of the principles of gluten digestion in beef cattle and corroborate recommendations that recognize beef as a naturally gluten-free food.

A Research Communication Brief: Gluten Analysis in Beef Samples Collected Using a Rigorous, Nationally Representative Sampling Protocol Confirms That Grain-Finished Beef Is Naturally Gluten-Free

PubMed Central

McNeill, Shalene H.; Cifelli, Amy M.; Roseland, Janet M.; Belk, Keith E.; Gehring, Kerri B.; Brooks, J. Chance; Thompson, Leslie D.

2017-01-01

Knowing whether or not a food contains gluten is vital for the growing number of individuals with celiac disease and non-celiac gluten sensitivity. Questions have recently been raised about whether beef from conventionally-raised, grain-finished cattle may contain gluten. To date, basic principles of ruminant digestion have been cited in support of the prevailing expert opinion that beef is inherently gluten-free. For this study, gluten analysis was conducted in beef samples collected using a rigorous nationally representative sampling protocol to determine whether gluten was present. The findings of our research uphold the understanding of the principles of gluten digestion in beef cattle and corroborate recommendations that recognize beef as a naturally gluten-free food. PMID:28841165

Simulation of Magnetic Field Assisted Finishing (MFAF) Process Utilizing Smart MR Polishing Tool

NASA Astrophysics Data System (ADS)

Barman, Anwesa; Das, Manas

2017-02-01

Magnetic field assisted finishing process is an advanced finishing process. This process is capable of producing nanometer level surface finish. In this process magnetic field is applied to control the finishing forces using magnetorheological polishing medium. In the current study, permanent magnet is used to provide the required magnetic field in the finishing zone. The working gap between the workpiece and the magnet is filled with MR fluid which is used as the polishing brush to remove surface undulations from the top surface of the workpiece. In this paper, the distribution of magnetic flux density on the workpiece surface and behaviour of MR polishing medium during finishing are analyzed using commercial finite element packages (Ansys Maxwell® and Comsol®). The role of magnetic force in the indentation of abrasive particles on the workpiece surface is studied. A two-dimensional simulation study of the steady, laminar, and incompressible MR fluid flow behaviour during finishing process is carried out. The material removal and surface roughness modelling of the finishing process are also presented. The indentation force by a single active abrasive particle on the workpiece surface is modelled during simulation. The velocity profile of MR fluid with and without application of magnetic field is plotted. It shows non-Newtonian property without application of magnetic field. After that the total material displacement due to one abrasive particle is plotted. The simulated roughness profile is in a good agreement with the experimental results. The conducted study will help in understanding the fluid behavior and the mechanism of finishing during finishing process. Also, the modelling and simulation of the process will help in achieving better finishing performance.

Wall finish selection in hospital design: a survey of facility managers.

PubMed

Lavy, Sarel; Dixit, Manish K

2012-01-01

This paper seeks to analyze healthcare facility managers' perceptions regarding the materials used for interior wall finishes and the criteria used to select them. It also examines differences in wall finish materials and the selection process in three major hospital spaces: emergency, surgery, and in-patient units. These findings are compared with healthcare designers' perceptions on similar issues, as currently documented in the literature. Hospital design and the materials used for hospital construction have a considerable effect on the environment and health of patients. A 2002 survey revealed which characteristics healthcare facility designers consider when selecting materials for healthcare facilities; however, no similar study has examined the views of facility managers on building finish selection. A 22-question survey questionnaire was distributed to 210 facility managers of metropolitan, for-profit hospitals in Texas; IRB approval was obtained. Respondents were asked to rank 10 interior wall finish materials and 11 selection criteria for wall finishes. Data from 48 complete questionnaires were analyzed using descriptive statistics and nonparametric statistical analysis methods. The study found no statistically significant differences in terms of wall finish materials or the characteristics for material selection in the three major spaces studied. It identified facility managers' four most-preferred wall finish materials and the five-most preferred characteristics, with a statistical confidence level of greater than 95%. The paper underscores the importance of incorporating all perspectives: facility designers and facility managers should work together toward achieving common organizational goals.

A survey of telerobotic surface finishing

NASA Astrophysics Data System (ADS)

Höglund, Thomas; Alander, Jarmo; Mantere, Timo

2018-05-01

This is a survey of research published on the subjects of telerobotics, haptic feedback, and mixed reality applied to surface finishing. The survey especially focuses on how visuo-haptic feedback can be used to improve a grinding process using a remote manipulator or robot. The benefits of teleoperation and reasons for using haptic feedback are presented. The use of genetic algorithms for optimizing haptic sensing is briefly discussed. Ways of augmenting the operator's vision are described. Visual feedback can be used to find defects and analyze the quality of the surface resulting from the surface finishing process. Visual cues can also be used to aid a human operator in manipulating a robot precisely and avoiding collisions.

Surface texture of resin-modified glass ionomer cements: effects of finishing/polishing time.

PubMed

Yap, A U J; Ong, S B; Yap, W Y; Tan, W S; Yeo, J C

2002-01-01

This study compared the surface texture of resin-modified glass ionomer cements after immediate and delayed finishing with different finishing/polishing systems. Class V preparations were made on the buccal and lingual/palatal surfaces of 64 freshly extracted teeth. The cavities on each tooth were restored with Fuji II LC (GC) and Photac-Fil Quick (3M-ESPE) according to manufacturers' instructions. Immediately after light-polymerization, gross finishing was done with 8-fluted tungsten carbide burs. The teeth were then randomly divided into four groups of 16 teeth. Half of the teeth in each group were finished immediately, while the remaining half were finished after one-week storage in distilled water at 37 degrees C. The following finishing/polishing systems were employed: (a) Robot Carbides; (b) Super-Snap system; (c) OneGloss and (d) CompoSite Polishers. The mean surface roughness (microm; n=8) in vertical (RaV) and horizontal (RaH) axis was measured using a profilometer. Data was subjected to ANOVA/Scheffe's tests and Independent Samples t-test at significance level 0.05. Ra values were generally lower in both vertical and horizontal axis with delayed finishing/polishing. Although significant differences in RaV and RaH values were observed among several systems with immediate finishing/polishing, only one (Fuji II LC: RaH - Super-Snap < Robot Carbides) was observed with delayed finishing.

Electro-rheological finishing for optical surfaces

NASA Astrophysics Data System (ADS)

Cheng, Haobo; Wang, Peng

2009-05-01

Many polishing techniques such as fixed-abrasive polishing, abrasive-free polishing and magnetorheological finishing etc., have been developed. Meanwhile, a new technique is proposed using the mixture of the electro-rheological (Er) fluid with abrasives as polishing slurry, which is a special process does not require pad. Electrorheological fluid is a special suspension liquid, whose viscosity has an approximate proportional relation with the electric strength applied. When the field strength reaches a certain limit, the phase transition occurs and the liquid acquires a solid like character, and while the electric field is removed, the fluid regains its original viscosity during the order of milliseconds. In this research work, we employed the characteristics of viscosity change of Er fluid to hold the polishing particles for micromachining. A point-contact electro-rheological finishing (Erf) tool was designed with a tip diameter 0.5~1mm. Both the anode and the cathode of the electric field were combined in the tool. The electric field could be controllable. When the tool moves across the profile of the work piece, by controlling the electric field strength as well as the other manufacturing parameters we can assure the deterministic material removal. Furthermore, the electro-rheological finishing process has been planned in detailed.

Finished Prokaryotic Genome Assemblies from a Low-cost Combination of Short and Long Reads (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yin, Shuangye

2012-06-01

Shuangye Yin on "Finished prokaryotic genome assemblies from a low-cost combination of short and long reads"; at the 2012 Sequencing, Finishing, Analysis in the Future Meeting held June 5-7, 2012 in Santa Fe, New Mexico.

Heavy Metals in Spring and Bottled Drinking Waters of Sibylline Mountains National Park (Central Italy).

PubMed

Annibaldi, Anna; Illuminati, Silvia; Truzzi, Cristina; Scarponi, Giuseppe

2018-02-01

Heavy metal concentrations (cadmium, lead, and copper) in spring, tap, and bottled waters of the Sibylline Mountains National Park (central Italy) were investigated using square wave anodic stripping voltammetry from 2004 to 2011. The mean (±SD) concentrations detected (1.3 ± 0.4 ng L -1 cadmium, 14 ± 6 ng L -1 lead, and 0.16 ± 0.10 μg L -1 copper) were below the limits stipulated by Italian and European legislation for drinking and natural mineral water. In the three studied areas of the park (Mount Bove north, Mount Bove south, and springs of River Nera) with very few exceptions, both mineral waters bottled in the area and aqueduct waters from public fountains had approximately the same metal concentrations as did the spring waters from which they were derived. Conversely, substantially higher metal concentrations were found at some sites in private houses, which may be due to release of metals from old metal pipes. At the time of this study, waters of Sibylline Mountains National Park were of good quality, and no influence of the bottling process on heavy metal concentrations was found.

Metal shell technology based upon hollow jet instability. [for inertial confinement fusion

NASA Technical Reports Server (NTRS)

Kendall, J. M.; Lee, M. C.; Wang, T. G.

1982-01-01

Spherical shells of submillimeter size are sought as ICF targets. Such shells must be dimensionally precise, smooth, of high strength, and composed of a high atomic number material. A technology for the production of shells based upon the hydrodynamic instability of an annular jet of molten metal is described. Shells in the 0.7-2.0 mm size range have been produced using tin as a test material. Specimens exhibit good sphericity, fair concentricity, and excellent finish over most of the surface. Work involving a gold-lead-antimony alloy is in progress. Droplets of this are amorphous and possess superior surface finish. The flow of tin models that of the alloy well; experiments on both metals show that the technique holds considerable promise.

40 CFR 463.30 - Applicability; description of the finishing water subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS PLASTICS MOLDING AND FORMING POINT SOURCE CATEGORY Finishing... the finishing water subcategory are processes where water comes in contact with the plastic product...

40 CFR 463.30 - Applicability; description of the finishing water subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS PLASTICS MOLDING AND FORMING POINT SOURCE CATEGORY Finishing... the finishing water subcategory are processes where water comes in contact with the plastic product...

Protecting wood decks from biodegradation and weathering : evaluation of deck finish systems

Treesearch

J. J. Morrell; P. F. Schneider; R. Sam Williams

2001-01-01

Mildew resistance, water repellency, and overall finish appearance were evaluated for 32 deck finishes on western redcedar (Thuja plicata D. Donn.) and Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) after 12, 21, and 39 months of outdoor exposure in western Oregon. The finishes were either solvent-borne or waterborne; were ei- ther clear, tinted, or lightly...

Concrete Finisher Program. Apprenticeship Training.

ERIC Educational Resources Information Center

Alberta Learning, Edmonton. Apprenticeship and Industry Training.

This document presents information about the apprenticeship training program of Alberta, Canada, in general and the concrete finishing program in particular. The first part of the document discusses the following items: Alberta's apprenticeship and industry training system; the apprenticeship and industry training committee structure; local…

Enhancing Surface Finish of Additively Manufactured Titanium and Cobalt Chrome Elements Using Laser Based Finishing

NASA Astrophysics Data System (ADS)

Gora, Wojciech S.; Tian, Yingtao; Cabo, Aldara Pan; Ardron, Marcus; Maier, Robert R. J.; Prangnell, Philip; Weston, Nicholas J.; Hand, Duncan P.

Additive manufacturing (AM) offers the possibility of creating a complex free form object as a single element, which is not possible using traditional mechanical machining. Unfortunately the typically rough surface finish of additively manufactured parts is unsuitable for many applications. As a result AM parts must be post-processed; typically mechanically machined and/or and polished using either chemical or mechanical techniques (both of which have their limitations). Laser based polishing is based on remelting of a very thin surface layer and it offers potential as a highly repeatable, higher speed process capable of selective area polishing, and without any waste problems (no abrasives or liquids). In this paper an in-depth investigation of CW laser polishing of titanium and cobalt chrome AM elements is presented. The impact of different scanning strategies, laser parameters and initial surface condition on the achieved surface finish is evaluated.

National Apprenticeship and Training Standards for the Sheet Metal Industry. Revised.

ERIC Educational Resources Information Center

Employment and Training Administration (DOL), Washington, DC. Bureau of Apprenticeship and Training.

These national standards are designed to aid contractors, labor, and joint committees in setting up, conducting, and improving apprenticeship programs for individuals seeking to become skilled in the sheet metal industry. Covered in the individual sections are the following topics: the provisions of the apprenticeship standards (definitions,…

40 CFR 425.40 - Applicability; description of the retan-wet finish-sides subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... retan-wet finish-sides subcategory. 425.40 Section 425.40 Protection of Environment ENVIRONMENTAL... CATEGORY Retan-Wet Finish-Sides Subcategory § 425.40 Applicability; description of the retan-wet finish-sides subcategory. The provisions of this subpart are applicable to process wastewater discharges...

8. This metal chute in building #3 carried the cloth ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. This metal chute in building #3 carried the cloth bags full of finished tire chains from upper floors to the warehouse on the first floor. - American Chain & Cable Company, East Princess Street (400 Block), York, York County, PA

Metal-on-metal hip joint tribology.

PubMed

Dowson, D; Jin, Z M

2006-02-01

The basic tribological features of metal-on-metal total hip replacements have been reviewed to facilitate an understanding of the engineering science underpinning the renaissance of these hard-on-hard joints. Metal-on-polymer hip replacements operate in the boundary lubrication regime, thus leading to the design guidance to reduce the femoral head diameter as much as is feasible to minimize frictional torque and volumetric wear. This explains why the gold-standard implant of this form from the past half-century had a diameter of only 22.225 mm (7/8 in). Metal-on-metal implants can operate in the mild mixed lubrication regime in which much of the applied load is supported by elastohydrodynamic films. Correct tribological design leads to remarkably low steady state wear rates. Promotion of the most effective elastohydrodynamic films calls for the largest possible head diameters and the smallest clearances that can reasonably be adopted, consistent with fine surface finishes, good sphericity and minimal structural elastic deformation of the cup on its foundations. This guidance, which is opposite in form to that developed for metal-on-polymer joints, is equally valid for solid (monolithic) metallic heads on metallic femoral stems and surface replacement femoral shells. Laboratory measurements of friction and wear in metal-on-metal joints have confirmed their potential to achieve a very mild form of mixed lubrication. The key lies in the generation of effective elastohydrodynamic lubricating films of adequate thickness compared with the composite roughness of the head and cup. The calculation of the film thickness is by no means easy, but the full procedure is outlined and the use of an empirical formula that displays good agreement with calculations based upon the full numerical solutions is explained. The representation of the lambda ratio, lambda, embracing both film thickness and composite roughness, is described.

40 CFR 425.40 - Applicability; description of the retan-wet finish-sides subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... retan-wet finish-sides subcategory. 425.40 Section 425.40 Protection of Environment ENVIRONMENTAL... POINT SOURCE CATEGORY Retan-Wet Finish-Sides Subcategory § 425.40 Applicability; description of the retan-wet finish-sides subcategory. The provisions of this subpart are applicable to process wastewater...

40 CFR 425.40 - Applicability; description of the retan-wet finish-sides subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... retan-wet finish-sides subcategory. 425.40 Section 425.40 Protection of Environment ENVIRONMENTAL... POINT SOURCE CATEGORY Retan-Wet Finish-Sides Subcategory § 425.40 Applicability; description of the retan-wet finish-sides subcategory. The provisions of this subpart are applicable to process wastewater...

40 CFR 425.40 - Applicability; description of the retan-wet finish-sides subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... retan-wet finish-sides subcategory. 425.40 Section 425.40 Protection of Environment ENVIRONMENTAL... POINT SOURCE CATEGORY Retan-Wet Finish-Sides Subcategory § 425.40 Applicability; description of the retan-wet finish-sides subcategory. The provisions of this subpart are applicable to process wastewater...

Nitenpyram degradation in finished drinking water.

PubMed

Noestheden, Matthew; Roberts, Simon; Hao, Chunyan

2016-07-15

Neonicotinoid pesticides and their metabolites have been indicated as contributing factors in the decline of honey bee colonies. A thorough understanding of neonicotinoid toxicity requires knowledge of their metabolites and environmental breakdown products. This work investigated the rapid degradation of the neonicotinoid nitenpyram in finished drinking water. Nitenpyram reaction products were characterized using liquid chromatography/quadrupole time-of-flight mass spectrometry (LC/QTOFMS). A software algorithm that compared degraded and control samples was utilized to facilitate efficient data reduction. Fragmentation pathways for six reaction products and nitenpyram were proposed using predictive software and manual product ion analysis. This study showed that nitenpyram degradation in unpreserved finished drinking water was likely the result of oxidation, hydrolysis and reaction with Cl2 . Structures for six nitenpyram reaction products were proposed that suggest the C9/C11 olefin as the key reactive site. Similarities between the identified nitenpyram reaction products and imidacloprid metabolites highlight the importance of this study, as the toxicity of neonicotinoids to pollinators has been linked to their metabolites. Based on the proposed reaction mechanisms, the identified nitenpyram reaction products in finished drinking water could also be present in the environment and water treatment facilities. As such, identifying these degradation products will aid in evaluating the environmental impact of neonicotinoid pesticides. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Marginal Fit of Metal-Ceramic Copings: Effect of Luting Cements and Tooth Preparation Design.

PubMed

de Almeida, Juliana Gomes Dos Santos Paes; Guedes, Carlos Gramani; Abi-Rached, Filipe de Oliveira; Trindade, Flávia Zardo; Fonseca, Renata Garcia

2017-12-22

To evaluate the effect of the triad finish line design, axial wall convergence angle, and luting cement on the marginal fit of metal copings used in metal-ceramic crowns. Schematic dies and their respective copings were cast in NiCr alloy. The dies exhibited the following finish line/convergence angle combinations: sloping shoulder/6°, sloping shoulder/20°, shoulder/6°, shoulder/20°. Marginal fit was evaluated under a stereomicroscope, before and after cementation. Copings were air-abraded with 50 μm Al 2 O 3 particles and cemented with Cimento de Zinco, RelyX U100, or Panavia F cements (n = 10/group). Data were square-root transformed and analyzed by 3-way factorial random effect model and Tukey's post hoc test (α = 0.05). Statistical analysis showed significance for the interactions finish line and convergence angle (p < 0.05), convergence angle and time (p < 0.001), and luting cement and time (p < 0.001). Sloping shoulder/20° provided the highest marginal discrepancy when compared to the other finish line/convergence angle combinations, which were statistically similar among each other. For both convergence angles and for all luting cements, the marginal discrepancy was significantly higher after cementation. Before and after cementation, 6° provided better marginal fit than 20°. After cementation, Panavia F provided higher marginal discrepancy than Cimento de Zinco. Lower convergence angle combined with shoulder and a low-consistency luting cement is preferable to cement metal copings. © 2017 by the American College of Prosthodontists.

Metal tube reducer is inexpensive and simple to operate

NASA Technical Reports Server (NTRS)

Mayfield, R. M.

1967-01-01

Low-cost metal tube reducer accepts tubing up to 1 inch outer diameter and can reduce this diameter to less than 1/2 inch with controlled wall thickness. This device can reduce all of the tube without waste. It produces extremely good surface finishes.

Los Alamos National Laboratory Overview

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neu, Mary

Mary Neu, Associate Director for Chemistry, Life and Earth Sciences at Los Alamos National Laboratory, delivers opening remarks at the "Sequencing, Finishing, Analysis in the Future" meeting in Santa Fe, NM.

Surface finishing. [for aircraft wings

NASA Technical Reports Server (NTRS)

Kinzler, J. A.; Heffernan, J. T.; Fehrenkamp, L. G.; Lee, W. S. (Inventor)

1977-01-01

A surface of an article adapted for relative motion with a fluid environment is finished by coating the surface with a fluid adhesive. The adhesive is covered with a sheet of flexible film material under tension, and the adhesive is set while maintaining tension on the film material.

Acidic magnetorheological finishing of infrared polycrystalline materials.

PubMed

Salzman, S; Romanofsky, H J; West, G; Marshall, K L; Jacobs, S D; Lambropoulos, J C

2016-10-20

Chemical-vapor-deposited (CVD) ZnS is an example of a polycrystalline material that is difficult to polish smoothly via the magnetorheological finishing (MRF) technique. When MRF-polished, the internal infrastructure of the material tends to manifest on the surface as millimeter-sized "pebbles," and the surface roughness observed is considerably high. The fluid's parameters important to developing a magnetorheological (MR) fluid that is capable of polishing CVD ZnS smoothly were previously discussed and presented. These parameters were acidic pH (∼4.5) and low viscosity (∼47  cP). MRF with such a unique MR fluid was shown to reduce surface artifacts in the form of pebbles; however, surface microroughness was still relatively high because of the absence of a polishing abrasive in the formulation. In this study, we examine the effect of two polishing abrasives-alumina and nanodiamond-on the surface finish of several CVD ZnS substrates, and on other important IR polycrystalline materials that were finished with acidic MR fluids containing these two polishing abrasives. Surface microroughness results obtained were as low as ∼28  nm peak-to-valley and ∼6-nm root mean square.

Acidic magnetorheological finishing of infrared polycrystalline materials

DOE PAGES

Salzman, S.; Romanofsky, H. J.; West, G.; ...

2016-10-12

Here, chemical-vapor–deposited (CVD) ZnS is an example of a polycrystalline material that is difficult to polish smoothly via the magnetorheological–finishing (MRF) technique. When MRF-polished, the internal infrastructure of the material tends to manifest on the surface as millimeter-sized “pebbles,” and the surface roughness observed is considerably high. The fluid’s parameters important to developing a magnetorheological (MR) fluid that is capable of polishing CVD ZnS smoothly were previously discussed and presented. These parameters were acidic pH (~4.5) and low viscosity (~47 cP). MRF with such a unique MR fluid was shown to reduce surface artifacts in the form of pebbles; however,more » surface microroughness was still relatively high because of the absence of a polishing abrasive in the formulation. In this study, we examine the effect of two polishing abrasives—alumina and nanodiamond—on the surface finish of several CVD ZnS substrates, and on other important IR polycrystalline materials that were finished with acidic MR fluids containing these two polishing abrasives. Surface microroughness results obtained were as low as ~28 nm peak-to-valley and ~6-nm root mean square.« less

The influence of temperature and humidity on printed wiring board surface finishes: Immersion tin vs organic azoles

NASA Astrophysics Data System (ADS)

Ray, U.; Artaki, I.; Gordon, H. M.; Vianco, P. T.

1994-08-01

Substitution of lead-free solders in electronic assemblies requires changes in the conventional Sn:Pb finishes on substrates and component leads to prevent contamination of the candidate lead-free solder. Options for solderability preservative coatings on the printed wiring board include organic (azole or rosin/resin based) films and tin-based plated metallic coatings. This paper compares the solderability performance and corrosion protection effectiveness of electroless tin coatings vs organic azole films after exposure to a series of humidity and thermal cycling conditions. The solderability of immersion tin is directly related to the tin oxide growth on the surface and is not affected by the formation of SnCu intermetallic phases as long as the intermetallic phase is underneath a protective Sn layer. Thin azole films decompose upon heating in the presence of oxygen and lead to solderability degradation. Evaluations of lead-free solder pastes for surface mount assembly applications indicate that immersion tin significantly improves the spreading of Sn:Ag and Sn:Bi alloys as compared to azole surface finishes.

Approaches for in silico finishing of microbial genome sequences

PubMed Central

Kremer, Frederico Schmitt; McBride, Alan John Alexander; Pinto, Luciano da Silva

2017-01-01

Abstract The introduction of next-generation sequencing (NGS) had a significant effect on the availability of genomic information, leading to an increase in the number of sequenced genomes from a large spectrum of organisms. Unfortunately, due to the limitations implied by the short-read sequencing platforms, most of these newly sequenced genomes remained as “drafts”, incomplete representations of the whole genetic content. The previous genome sequencing studies indicated that finishing a genome sequenced by NGS, even bacteria, may require additional sequencing to fill the gaps, making the entire process very expensive. As such, several in silico approaches have been developed to optimize the genome assemblies and facilitate the finishing process. The present review aims to explore some free (open source, in many cases) tools that are available to facilitate genome finishing. PMID:28898352

Approaches for in silico finishing of microbial genome sequences.

PubMed

Kremer, Frederico Schmitt; McBride, Alan John Alexander; Pinto, Luciano da Silva

The introduction of next-generation sequencing (NGS) had a significant effect on the availability of genomic information, leading to an increase in the number of sequenced genomes from a large spectrum of organisms. Unfortunately, due to the limitations implied by the short-read sequencing platforms, most of these newly sequenced genomes remained as "drafts", incomplete representations of the whole genetic content. The previous genome sequencing studies indicated that finishing a genome sequenced by NGS, even bacteria, may require additional sequencing to fill the gaps, making the entire process very expensive. As such, several in silico approaches have been developed to optimize the genome assemblies and facilitate the finishing process. The present review aims to explore some free (open source, in many cases) tools that are available to facilitate genome finishing.

Metal loading in Soda Butte Creek upstream of Yellowstone National Park, Montana and Wyoming; a retrospective analysis of previous research; and quantification of metal loading, August 1999

USGS Publications Warehouse

Boughton, G.K.

2001-01-01

Acid drainage from historic mining activities has affected the water quality and aquatic biota of Soda Butte Creek upstream of Yellowstone National Park. Numerous investigations focusing on metals contamination have been conducted in the Soda Butte Creek basin, but interpretations of how metals contamination is currently impacting Soda Butte Creek differ greatly. A retrospective analysis of previous research on metal loading in Soda Butte Creek was completed to provide summaries of studies pertinent to metal loading in Soda Butte Creek and to identify data gaps warranting further investigation. Identification and quantification of the sources of metal loading to Soda Butte Creek was recognized as a significant data gap. The McLaren Mine tailings impoundment and mill site has long been identified as a source of metals but its contribution relative to the total metal load entering Yellowstone National Park was unknown. A tracer-injection and synoptic-sampling study was designed to determine metal loads upstream of Yellowstone National Park.A tracer-injection and synoptic-sampling study was conducted on an 8,511-meter reach of Soda Butte Creek from upstream of the McLaren Mine tailings impoundment and mill site downstream to the Yellowstone National Park boundary in August 1999. Synoptic-sampling sites were selected to divide the creek into discrete segments. A lithium bromide tracer was injected continuously into Soda Butte Creek for 24.5 hours. Downstream dilution of the tracer and current-meter measurements were used to calculate the stream discharge. Stream discharge values, combined with constituent concentrations obtained by synoptic sampling, were used to quantify constituent loading in each segment of Soda Butte Creek.Loads were calculated for dissolved calcium, silica, and sulfate, as well as for dissolved and total-recoverable iron, aluminum, and manganese. Loads were not calculated for cadmium, copper, lead, and zinc because these elements were infrequently

Superficial roughness on composite surface, composite-enamel and composite-dentin junctions after different finishing and polishing procedures. Part II: roughness with diamond finishing and differences between enamel composite vs body composite.

PubMed

Ferraris, Federico; Conti, Alessandro

2014-01-01

The following study asks three principle questions relative to composite finishing and composite polishing: 1) Will the superficial roughness of different restoration surfaces have different values, utilizing the same polishing system (multistep), after finishing with the tungsten carbide or diamond bur? 2) Under the same conditions of finishing and polishing sequences, will the composite surfaces (C), the composite-enamel (CE) and composite-dentin (CD) interfaces show different roughness values? 3) Will the surface roughness of composites of different translucency in the various phases of finishing and polishing, and on different interfaces, have different results? The null hypothesis is represented by the fact that there are no significant differences on roughness of composite restorations when polishing, after finishing with tungsten carbide or diamond burs. Furthermore, the null hypothesis is that there are no significant differences on roughness between polishing on composite surface, composite-enamel and composite-dentin interfaces, and finally there are no differences on roughness after finishing and polishing of two composite with different translucency. For the study, 56 class V cavities were prepared on extracted teeth. Restorations were done in nanofilled composite Filtek XTE (3M Espe) in a standard fashion, and then finished and polished. The 28 buccal cavities were restored on the surface with composite enamel and the 28 palatals with composite body. Finishing was done with fine toothing burs in tungsten carbide (16 blades) or fine grit diamond burs (46 μm), and made by the same manufacturer (Komet). The second phase of finishing was done with burs (with the same form as already mentioned) ultrafine toothing tungsten carbide (30 blades) or with extra and ultrafine grit diamond (25 and 8 μm). The polishing phase for both of the earlier sequences was done with the application of three rubber tips with decreasing abrasiveness and an application with a

Levels of selected metals in leaves of Cannabis sativa L. cultivated in Ethiopia.

PubMed

Zerihun, Agalu; Chandravanshi, Bhagwan Singh; Debebe, Ayalew; Mehari, Bewketu

2015-01-01

Cannabis sativa L. is one of the illicit drug bearing plants. Cannabis products are the most widely trafficked drugs worldwide. The highest levels of cannabis production in the world take place in the African continent. A small volume of cannabis is produced in rural areas of Ethiopia, of which a small portion is exported to neighboring countries and the majority is consumed at home. The literature survey revealed that there is no report on the metal contents in cannabis cultivated in Ethiopia. The main objective of this study is to determine the level of selected metals in leaves of Cannabis sativa L. cultivated in Ethiopia. Cannabis sativa L. samples were collected from Metema (Amhara Region), Mekelle (Tigray Region), Sheshemene (Oromia Region) and Butajira (South Nations Nationality and Peoples (SNNP) Region) of Ethiopia. After proper sample pretreatment, the volumes of reagents used, digestion temperature and digestion time were optimized and using the optimized conditions the levels of metals were determined by flame atomic absorption spectrometry. The accuracy of the optimized procedure was evaluated by analyzing the digest of the spiked samples with standard solution and the percentage recoveries varied from 88 to 103%. The levels of metals determined (µg/g dry weight) were in the ranges Ca (657-1,511), Zn (321-380), Ni (124-172), Cu (122-176), Cd (3-10), Pb (8-10), and Cr (4-8). Zn was with the highest concentration among trace metals. A statistical analysis of variance (ANOVA) at 95% confidence level indicated that there is a significant difference in the levels of all the metals between the four sample means except Pb. The results indicate that the content of Pb and Cd exceeds the permissible amount for medicinal plants which form the raw materials for the finished products set by World Health Organization (WHO).

METHOD OF HOT ROLLING URANIUM METAL

DOEpatents

Kaufmann, A.R.

1959-03-10

A method is given for quickly and efficiently hot rolling uranium metal in the upper part of the alpha phase temperature region to obtain sound bars and sheets possessing a good surface finish. The uranium metal billet is heated to a temperature in the range of 1000 deg F to 1220 deg F by immersion iii a molten lead bath. The heated billet is then passed through the rolls. The temperature is restored to the desired range between successive passes through the rolls, and the rolls are turned down approximately 0.050 inch between successive passes.

Co-extrusion of semi-finished aluminium-steel compounds

NASA Astrophysics Data System (ADS)

Thürer, S. E.; Uhe, J.; Golovko, O.; Bonk, C.; Bouguecha, A.; Klose, C.; Behrens, B.-A.; Maier, H. J.

2017-10-01

The combination of light metals and steels allows for new lightweight components with wear-resistant functional surfaces. Within the Collaborative Research Centre 1153 novel process chains are developed for the manufacture of such hybrid components. Here, the production process of a hybrid bearing bushing made of the aluminium alloy EN AW-6082 and the case-hardened steel 20MnCr5 is developed. Hybrid semi-finished products are an attractive alternative to conventional ones resulting from massive forming processes where the individual components are joined after the forming process. The actual hybrid semi-finished products were manufactured using a lateral angular co-extrusion (LACE) process. The bearing bushings are subsequently produced by die forging. In the present study, a tool concept for the LACE process is described, which renders the continuous joining of a steel rod with an aluminium tube possible. During the LACE process, the rod is fed into the extrusion die at an angle of approx. 90°. Metallographic analysis of the hybrid profile showed that the mechanical bonding between the different materials begins about 75 mm after the edge of the aluminium sheath. In order to improve the bonding strength, the steel rod is to be preheated during extrusion. Systematic investigations using a dilatometer, considering the maximum possible co-extrusion process parameters, were carried out. The variable parameters for the dilatometer experiments were determined by numerical simulation. In order to form a bond between the materials, the oxide layer needs to be disrupted during the co-extrusion process. In an attempt to better understand this effect, a modified sample geometry with chamfered steel was developed for the dilatometer experiments. The influence of the process parameters on the formation of the intermetallic phase at the interface was analysed by scanning electron microscopy and X-ray diffraction. This article, which was originally published online on 16

Chronicle of 65 years of wood finishing research at the Forest Products Laboratory

Treesearch

Thomas M. Gorman; William C. Feist

1989-01-01

For 65 years, the Forest Products Laboratory (FPL) in Madison, Wisconsin, has had a continuous and extensive program of research on finishing wood for outdoor use. The research has stressed the fundamental aspects of wood weathering and the interactions of pretreatments and finishes on wood surfaces. This report outlines the history of the FPL wood finishing research...

Durability of exterior natural wood finishes in the Pacific Northwest

Treesearch

William C. Feist; Edward A. Mraz

1980-01-01

There is a growing demand for natural exterior wood finishes that retain the original attractive appearance of wood with the least change in color and masking of grain. A number of experimental finishes are being evaluated for their performance in the cool, moist climate of Olympia, Wash. This study, started in 1966, has included observations on the weathering...

Evaluation of ENEPIG and Immersion Silver Surface Finishes Under Drop Loading

NASA Astrophysics Data System (ADS)

Pearl, Adam; Osterman, Michael; Pecht, Michael

2016-01-01

The effect of printed circuit board surface finish on the drop loading reliability of ball grid array (BGA) solder interconnects has been examined. The finishes examined include electroless nickel/electroless palladium/immersion gold (ENEPIG) and immersion silver (ImAg). For the ENEPIG finish, the effect of the Pd plating layer thickness was evaluated by testing two different thicknesses: 0.05 μm and 0.15 μm. BGA components were assembled onto the boards using either eutectic Sn-Pb or Sn-3.0Ag-0.5Cu (SAC305) solder. Prior to testing, the assembled boards were aged at 100°C for 24 h or 500 h. The boards were then subjected to multiple 1500-g drop tests. Failure analysis indicated the primary failure site for the BGAs to be the solder balls at the board-side solder interface. Cratering of the board laminate under the solder-attached pads was also observed. In all cases, isothermal aging reduced the number of drops to failure. The components soldered onto the boards with the 0.15- μm-Pd ENEPIG finish with the SAC305 solder had the highest characteristic life, at 234 drops to failure, compared with the other finish-solder combinations.

Ultra-smooth finishing of aspheric surfaces using CAST technology

NASA Astrophysics Data System (ADS)

Kong, John; Young, Kevin

2014-06-01

Growing applications for astronomical ground-based adaptive systems and air-born telescope systems demand complex optical surface designs combined with ultra-smooth finishing. The use of more sophisticated and accurate optics, especially aspheric ones, allows for shorter optical trains with smaller sizes and a reduced number of components. This in turn reduces fabrication and alignment time and costs. These aspheric components include the following: steep surfaces with large aspheric departures; more complex surface feature designs like stand-alone off-axis-parabola (OAP) and free form optics that combine surface complexity with a requirement for ultra-high smoothness, as well as special optic materials such as lightweight silicon carbide (SiC) for air-born systems. Various fabrication technologies for finishing ultra-smooth aspheric surfaces are progressing to meet these growing and demanding challenges, especially Magnetorheological Finishing (MRF) and ion-milling. These methods have demonstrated some good success as well as a certain level of limitations. Amongst them, computer-controlled asphere surface-finishing technology (CAST), developed by Precision Asphere Inc. (PAI), plays an important role in a cost effective manufacturing environment and has successfully delivered numerous products for the applications mentioned above. One of the most recent successes is the Gemini Planet Imager (GPI), the world's most powerful planet-hunting instrument, with critical aspheric components (seven OAPs and free form optics) made using CAST technology. GPI showed off its first images in a press release on January 7, 2014 . This paper reviews features of today's technologies in handling the ultra-smooth aspheric optics, especially the capabilities of CAST on these challenging products. As examples, three groups of aspheres deployed in astronomical optics systems, both polished and finished using CAST, will be discussed in detail.

APPROACHING ZERO DISCHARGE IN SURFACE FINISHING

EPA Science Inventory

This document provides guidance to surface finishing manufacturers on control technologies and process changes for approaching zero discharge (AZD). AZD is a key theme underlying the Strategic Goals Program (SGP). The SGP is a cooperative effort between the EPA nd the American El...

Effects of surface finishing conditions on the biocompatibility of a nickel-chromium dental casting alloy.

PubMed

McGinley, Emma Louise; Coleman, David C; Moran, Gary P; Fleming, Garry J P

2011-07-01

To assess the effects of surface finishing condition (polished or alumina particle air abraded) on the biocompatibility of direct and indirect exposure to a nickel-chromium (Ni-Cr) d.Sign®10 dental casting alloy on oral keratinocytes. Biocompatibility was performed by assessing cellular viability and morphology, metabolic activity, cellular toxicity and presence of inflammatory cytokine markers. Discs of d.Sign®10 were cast, alumina particle air abraded and half were polished before surface roughness was determined by profilometry. Biocompatibility was assessed by placing the discs directly or indirectly (with immersion solutions) into contact with TR146 monolayers. Metal ion release was determined by ICP-MS. Cell viability was assessed by trypan blue dye exclusion, metabolic activity by XTT and cellular toxicity by LDH. Inflammatory cytokine analysis was performed using sandwich ELISAs. The mean polished Ra value was significantly reduced (P<0.001) compared with the alumina particle air abraded discs but metal ion release was significantly increased for the polished discs. Significant reductions in cell density of polished compared with alumina particle air abraded discs was observed following direct or indirect exposure. A significant reduction in metabolic activity, increase in cellular toxicity and an increase in the presence of inflammatory cytokine markers was highlighted for the polished relative to the alumina particle air abraded discs at 24h. Finishing condition of the Ni-Cr dental alloy investigated has important clinical implications. The approach of employing cell density and morphology, metabolic activity, cellular toxicity levels and inflammatory marker responses to TR146 epithelial cells combined with ICP-MS afforded the authors an increased insight into the complex processes dental alloys undergo in the oral environment. Copyright © 2011 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

46 CFR 116.422 - Ceilings, linings, trim, interior finish and decorations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Ceilings, linings, trim, interior finish and decorations... PASSENGERS CONSTRUCTION AND ARRANGEMENT Fire Protection § 116.422 Ceilings, linings, trim, interior finish... accommodation spaces may have a combustible veneer trim and decorations that do not meet the requirements of...

46 CFR 116.422 - Ceilings, linings, trim, interior finish and decorations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Ceilings, linings, trim, interior finish and decorations... PASSENGERS CONSTRUCTION AND ARRANGEMENT Fire Protection § 116.422 Ceilings, linings, trim, interior finish... accommodation spaces may have a combustible veneer trim and decorations that do not meet the requirements of...

21 CFR 181.26 - Drying oils as components of finished resins.

Code of Federal Regulations, 2011 CFR

2011-04-01

... classified as drying oils, when migrating from food-packaging material (as components of finished resins... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Drying oils as components of finished resins. 181.26 Section 181.26 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 181.26 - Drying oils as components of finished resins.

Code of Federal Regulations, 2010 CFR

2010-04-01

... classified as drying oils, when migrating from food-packaging material (as components of finished resins... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Drying oils as components of finished resins. 181.26 Section 181.26 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 181.26 - Drying oils as components of finished resins.

Code of Federal Regulations, 2013 CFR

2013-04-01

... classified as drying oils, when migrating from food-packaging material (as components of finished resins... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Drying oils as components of finished resins. 181.26 Section 181.26 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 181.26 - Drying oils as components of finished resins.

Code of Federal Regulations, 2014 CFR

2014-04-01

... food-packaging material (as components of finished resins) shall include: Chinawood oil (tung oil... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Drying oils as components of finished resins. 181.26 Section 181.26 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

21 CFR 181.26 - Drying oils as components of finished resins.

Code of Federal Regulations, 2012 CFR

2012-04-01

... classified as drying oils, when migrating from food-packaging material (as components of finished resins... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Drying oils as components of finished resins. 181.26 Section 181.26 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

Studies on Application of Aroma Finish on Silk Fabric

NASA Astrophysics Data System (ADS)

Hipparagi, Sanganna Aminappa; Srinivasa, Thirumalappa; Das, Brojeswari; Naik, Subhas Venkatappa; Purushotham, Serampur Parappa

2016-10-01

Aromatic treatments on textiles have gained importance in the recent years. In the present article work has been done on fragrance finish application on silk material. Silk is an expensive natural fibre used for apparel purpose and known for its feel and appeal. Incorporation of fragrance material in silk product, will add more value to it. Present work focuses to impart durable aroma finish for silk products to be home washed or subjected to dry cleaning. Microencapsulated aroma chemical has been used for the treatment. Impregnation method, Exhaust method, Dip-Pad-Dry method and Spray method have been used to see the influence of application method on the uptake and performance. Evaluation of the aroma treated material has been done through subjective evaluation as per Odor Intensity Reference Scaling (OIRS). Effect of the aroma finishing on the physical properties of the fabric has also been studied. No adverse effect has been observed on the stiffness of the fabric after the aroma treatment.

Influence of the Cutting Conditions in the Surface Finishing of Turned Pieces of Titanium Alloys

NASA Astrophysics Data System (ADS)

Huerta, M.; Arroyo, P.; Sánchez Carrilero, M.; Álvarez, M.; Salguero, J.; Marcos, M.

2009-11-01

Titanium is a material that, despite its high cost, is increasingly being introduced in the aerospace industry due to both, its weight, its mechanical properties and its corrosion potential, very close to that of carbon fiber based composite material. This fact allows using Ti to form Fiber Metal Laminates Machining operations are usually used in the manufacturing processes of Ti based aerospace structural elements. These elements must be machined under high surface finish requirements. Previous works have shown the relationship between the surface roughness and the tool changes in the first instants of turning processes. From these results, new tests have been performed in an aeronautical factory, in order to analyse roughness in final pieces.

Effects of delayed finishing/polishing on surface roughness, hardness and gloss of tooth-coloured restorative materials.

PubMed

Yazici, A Ruya; Tuncer, Duygu; Antonson, Sibel; Onen, Alev; Kilinc, Evren

2010-01-01

The aim of this study was to investigate the effect of delayed finishing/polishing on the surface roughness, hardness and gloss of tooth-coloured restorative materials. Four different tooth-coloured restoratives: a flowable resin composite- Tetric Flow, a hybrid resin composite- Venus, a nanohybrid resin composite- Grandio, and a polyacid modified resin composite- Dyract Extra were used. 30 specimens were made for each material and randomly assigned into three groups. The first group was finished/polished immediately and the second group was finished/polished after 24 hours. The remaining 10 specimens served as control. The surface roughness of each sample was recorded using a laser profilometer. Gloss measurements were performed using a small-area glossmeter. Vickers microhardness measurements were performed from three locations on each specimen surface under 100g load and 10s dwell time. Data for surface roughness and hardness were analyzed by Kruskal Wallis test and data for gloss were subjected to one-way ANOVA and Tukey test (P <.05). The smoothest surfaces were obtained under Mylar strip for all materials. While there were no significant differences in surface roughness of immediate and delayed finished/polished Dyract Extra samples, immediately finished/polished Venus and Grandio samples showed significantly higher roughness than the delayed polished samples (P <.05). In Tetric Flow samples, immediately finishing/polishing provided smoother surface than delayed finishing/polishing (P <.05). The highest gloss values were recorded under Mylar strip for all materials. While delayed finishing/polishing resulted in a significantly higher gloss compared to immediate finishing/polishing in Venus samples (P <.05), no differences were observed between delayed or immediate finishing/polishing for the other materials (P>.05). The lowest hardness values were found under Mylar strip. Delayed finishing/polishing significantly increased the hardness of all materials. The

Computer Modeling of Direct Metal Laser Sintering

NASA Technical Reports Server (NTRS)

Cross, Matthew

2014-01-01

A computational approach to modeling direct metal laser sintering (DMLS) additive manufacturing process is presented. The primary application of the model is for determining the temperature history of parts fabricated using DMLS to evaluate residual stresses found in finished pieces and to assess manufacturing process strategies to reduce part slumping. The model utilizes MSC SINDA as a heat transfer solver with imbedded FORTRAN computer code to direct laser motion, apply laser heating as a boundary condition, and simulate the addition of metal powder layers during part fabrication. Model results are compared to available data collected during in situ DMLS part manufacture.

Authorization basis supporting documentation for plutonium finishing plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

King, J.P., Fluor Daniel Hanford

1997-03-05

The identification and definition of the authorization basis for the Plutonium Finishing Plant (PFP) facility and operations are essential for compliance to DOE Order 5480.21, Unreviewed Safety Questions. The authorization basis, as defined in the Order, consists of those aspects of the facility design basis, i.e., the structures, systems and components (SSCS) and the operational requirements that are considered to be important to the safety of operations and are relied upon by DOE to authorize operation of the facility. These facility design features and their function in various accident scenarios are described in WHC-SD-CP-SAR-021, Plutonium Finishing Plant Final Safety Analysismore » Report (FSAR), Chapter 9, `Accident Analysis.` Figure 1 depicts the relationship of the Authorization Basis to its components and other information contained in safety documentation supporting the Authorization Basis. The PFP SSCs that are important to safety, collectively referred to as the `Safety Envelope` are discussed in various chapters of the FSAR and in WHC-SD-CP-OSR-010, Plutonium Finishing Plant Operational Safety Requirements. Other documents such as Criticality Safety Evaluation Reports (CSERS) address and support some portions of the Authorization Basis and Safety Envelope.« less

Concrete Finisher: Apprenticeship Course Outline. Apprenticeship and Industry Training. 4805.2

ERIC Educational Resources Information Center

Alberta Advanced Education, 2005

2005-01-01

The graduate of the Concrete Finisher apprenticeship program is a certified journeyperson who will be able to: (1) perform tests to confirm concrete quality; (2) interpret building codes, plans and specifications as they apply to the trade; (3) place and finish concrete in a professional manner; (4) cut, patch, maintain and repair concrete…

21 CFR 820.80 - Receiving, in-process, and finished device acceptance.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Receiving, in-process, and finished device acceptance. 820.80 Section 820.80 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... acceptance to ensure that each production run, lot, or batch of finished devices meets acceptance criteria...

21 CFR 820.80 - Receiving, in-process, and finished device acceptance.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Receiving, in-process, and finished device acceptance. 820.80 Section 820.80 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN... acceptance to ensure that each production run, lot, or batch of finished devices meets acceptance criteria...

40 CFR 410.40 - Applicability; description of the woven fabric finishing subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Applicability; description of the woven fabric finishing subcategory. 410.40 Section 410.40 Protection of Environment ENVIRONMENTAL PROTECTION... proofing, soil repellency application and a special finish application. ...

The effect of wet film thickness on VOC emissions from a finishing varnish.

PubMed

Lee, Shun-Cheng; Kwok, Ngai-Hong; Guo, Hai; Hung, Wing-Tat

2003-01-20

Finishing varnishes, a typical type of oil-based varnishes, are widely used to shine metal, wood trim and cabinet surfaces in Hong Kong. The influence of wet film thickness on volatile organic compound (VOC) emissions from a finishing varnish was studied in an environmental test chamber. The varnish was applied on an aluminium foil with three different wet film thickness (35.2, 69.9 and 107.3 microm). The experimental conditions were 25.0 degrees C, 50.0% relative humidity (RH) with an air exchange rate of 0.5 h(-1). The concentrations of the major VOCs were monitored for the first 10 h. The air samples were collected by canisters and analysed by gas chromatography/mass selective detector (GC/MSD). Six major VOCs including toluene, chlorobenzene, ethylbenzene, m,p-xylene, o-xylene and 1,3,5-trimethylbenzene were identified and quantified. Marked differences were observed for three different film thicknesses. VOC concentrations increased rapidly during the first few hours and then decreased as the emission rates declined. The thicker the wet film, the higher the VOC emissions. A model expression included an exponentially decreasing emission rate of varnish film. The concentration and time data measured in the chamber were used to determine the parameters of empirical emission rate model. The present work confirmed that the film thickness of varnish influenced markedly the concentrations and emissions of VOCs. Copyright 2002 Elsevier Science B.V.

8. Finish line, marked by white poles, as viewed from ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. Finish line, marked by white poles, as viewed from infield tote board. Shown are all the best locations for viewing the finish line, including the Clubhouse on the left and Original Grandstand on the right. For a similar view taken in 1939 by a photographer for the Seattle Post-Intelligencer newspaper, see photo WA-201-24. (August 1993) - Longacres, 1621 Southwest Sixteenth Street, Renton, King County, WA

40 CFR 425.90 - Applicability; description of the retan-wet finish-splits subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING POINT SOURCE... resulting from any tannery which processes previously unhaired and tanned splits into finished leather by...

76 FR 79221 - Penske Logistics, LLC, Customer Service Department General Motors and Tier Finished Goods...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-21

..., Customer Service Department General Motors and Tier Finished Goods/Finished Goods Division; a Subsidiary of... Manpower El Paso, TX; Amended Certification Regarding Eligibility To Apply for Worker Adjustment Assistance... should read Penske Logistics, LLC, Customer Service Department, General Motors and Tier Finished Goods...

40 CFR 425.40 - Applicability; description of the retan-wet finish-sides subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING POINT SOURCE... resulting from any tannery which processes previously tanned hides and skins (grain side only) into finished...

40 CFR Figure 1 to Subpart Tttt of... - Example Logs for Recording Leather Finish Use and HAP Content

Code of Federal Regulations, 2010 CFR

2010-07-01

... Finishing Operations Part 63, Subpt. TTTT, Fig. 1 Figure 1 to Subpart TTTT of Part 63—Example Logs for Recording Leather Finish Use and HAP Content Month:______Year:______ Finish Inventory Log Finish type Finish usage(pounds) HAP Content(mass fraction) Date and time Operator's name Product process operation Monthly...

Cross-Cultural Consumer Acceptability and Purchase Intent of Forage-Finished Rib-Eye Steaks.

PubMed

Torrico, Damir Dennis; Wardy, Wisdom; Pujols, Kairy Dharali; Carabante, Kennet Mariano; Jirangrat, Wannita; Scaglia, Guillermo; Janes, Marlene E; Prinyawiwatkul, Witoon

2015-10-01

Rib-eye steaks, from 3 forage-finished systems (S1, S2, and S3) and 1 commercial steak (C), either cooked by 1-sided-grilling or 2-sided-grilling, were evaluated for sensory acceptability [overall appearance (ORA) and overall appearance of fat (OAF) for raw steaks; overall appearance (OCA), overall beef aroma (OBA), overall beef flavor (OBF), juiciness, tenderness and overall liking (OL) for cooked steaks] and purchase intent by Hispanic, Asian and U.S. consumers. They also indicated preferred degree of doneness and cooking methods. Cross-cultural differences in preferences and consumer acceptability of rib-eye steaks were observed. Grilling was the most preferred cooking method. Hispanics and Asians preferred medium and/or medium well, while U.S. consumers preferred medium and/or medium rare. For cooked steaks, the population effect was significant for all sensory attributes; Asians generally scored lower than did Hispanics and U.S. consumers. C and S3 generally had higher scores for all sensory attributes across 3 populations. Purchase intent for all forage-finished steaks was higher for Hispanics and U.S. consumers compared to Asians (50.0% to 77.8% compared with 43.2% to 65.9%). Attributes influencing purchase intent of forage-finished steaks differed among populations: tenderness (odds ratio = 1.4) for Hispanics, OCA (odds ratio = 1.5) for Asians, and OBF (odds ratio = 1.3) for U.S. consumers. Overall, this study demonstrated that the type of forage-finished system and ethnic differences influenced sensory acceptability and purchase intent of forage-finished rib-eye steaks. Demand for forage-finished beef has increased worldwide due to its potential health benefits. Little is known regarding the cross-cultural effects on the consumer acceptance of forage-finished beef. We evaluated sensory acceptance and purchase intent of raw and cooked forage-finished rib-eye steaks using Hispanic, Asian, and U.S. (White and African American) populations. This study

From the Lab Bench: The challenges of finishing cattle on pasture

USDA-ARS?s Scientific Manuscript database

A column was written to discuss the challenges in Kentucky to finish beef calves on pasture. It might seem feasible to finish a calf in 24 months. This can be accomplished if the average daily weight gain is 1.0 pound per day, but the calves will spend almost half of those 24 months on pasture with ...

Effect of Plasma Surface Finish on Wettability and Mechanical Properties of SAC305 Solder Joints

NASA Astrophysics Data System (ADS)

Kim, Kyoung-Ho; Koike, Junichi; Yoon, Jeong-Won; Yoo, Sehoon

2016-12-01

The wetting behavior, interfacial reactions, and mechanical reliability of Sn-Ag-Cu solder on a plasma-coated printed circuit board (PCB) substrate were evaluated under multiple heat-treatments. Conventional organic solderability preservative (OSP) finished PCBs were used as a reference. The plasma process created a dense and highly cross-linked polymer coating on the Cu substrates. The plasma finished samples had higher wetting forces and shorter zero-cross times than those with OSP surface finish. The OSP sample was degraded after sequential multiple heat treatments and reflow processes, whereas the solderability of the plasma finished sample was retained after multiple heat treatments. After the soldering process, similar microstructures were observed at the interfaces of the two solder joints, where the development of intermetallic compounds was observed. From ball shear tests, it was found that the shear force for the plasma substrate was consistently higher than that for the OSP substrate. Deterioration of the OSP surface finish was observed after multiple heat treatments. Overall, the plasma surface finish was superior to the conventional OSP finish with respect to wettability and joint reliability, indicating that it is a suitable material for the fabrication of complex electronic devices.

Survey of quantitative antimicrobial consumption in two different pig finishing systems.

PubMed

Moreno, M A

2012-09-29

The primary objectives of this study were to: (a) collect on-farm antimicrobial use (AMU) data in fattener pigs employing two questionnaire-based surveys; (b) assess different quantitative measures for quantifying AMU in fattener pigs; (c) compare AMU in fattener pigs between two different management systems producing finishers: farrow-to-finish (FtF) farms versus finisher farms. Two questionnaires were designed both containing five groups of questions focused on the responder, the farm and AMU (eg, in-feed, in-drinking water and parenteral); both surveys were carried out by means of personal face-to-face interviews. Both surveys started with a sample size of 108 potentially eligible farms per survey; nevertheless, finally 67 finisher farms and 49 FtF farms were recruited. Overall percentages of animals exposed to antimicrobials (AM) were high (90 per cent in finisher farms and 54 per cent FtF farms); colistin (61 per cent and 33 per cent) and doxycycline (62 per cent and 23 per cent) were the most common AMs, followed by amoxicillin (51 per cent and 19 per cent) and lincomycin (49 per cent), respectively. Questionnaire-based surveys using face-to-face interviews are useful for capturing information regarding AMU at the farm level. Farm-level data per administration route can be used for comparative AMU analysis between farms. Nevertheless, for the analysis of the putative relationships between AMU and AM resistance, measures based on exposed animals or exposure events are needed.

UPTAKE OF HEAVY METALS IN BATCH SYSTEMS BY A RECYCLED IRON-BEARING MATERIAL

EPA Science Inventory

An iron-bearing material deriving from surface finishing operations in the manufacturing of cast-iron components demonstrates potential for removal of heavy metals from aqueous waste streams. Batch isotherm and rate experiments were conducted for uptake of cadmium, zinc, and lead...

40 CFR 410.50 - Applicability; description of the knit fabric finishing subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 29 2011-07-01 2009-07-01 true Applicability; description of the knit... AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS TEXTILE MILLS POINT SOURCE CATEGORY Knit Fabric Finishing Subcategory § 410.50 Applicability; description of the knit fabric finishing subcategory. The...

Microfabrication Method using a Combination of Local Ion Implantation and Magnetorheological Finishing

NASA Astrophysics Data System (ADS)

Han, Jin; Kim, Jong-Wook; Lee, Hiwon; Min, Byung-Kwon; Lee, Sang Jo

2009-02-01

A new microfabrication method that combines localized ion implantation and magnetorheological finishing is proposed. The proposed technique involves two steps. First, selected regions of a silicon wafer are irradiated with gallium ions by using a focused ion beam system. The mechanical properties of the irradiated regions are altered as a result of the ion implantation. Second, the wafer is processed by using a magnetorheological finishing method. During the finishing process, the regions not implanted with ion are preferentially removed. The material removal rate difference is utilized for microfabrication. The mechanisms of the proposed method are discussed, and applications are presented.

Comparison of gene expression and fatty acid profiles in concentrate and forage finished beef.

PubMed

Buchanan, J W; Garmyn, A J; Hilton, G G; VanOverbeke, D L; Duan, Q; Beitz, D C; Mateescu, R G

2013-01-01

Fatty acid profiles and intramuscular expression of genes involved in fatty acid metabolism were characterized in concentrate- (CO) and forage- (FO) based finishing systems. Intramuscular samples from the adductor were taken at slaughter from 99 heifers finished on a CO diet and 58 heifers finished on a FO diet. Strip loins were obtained at fabrication to evaluate fatty acid profiles of LM muscle for all 157 heifers by using gas chromatography fatty acid methyl ester analysis. Composition was analyzed for differences by using the General Linear Model (GLM) procedure in SAS. Differences in fatty acid profile included a greater atherogenic index, greater percentage total MUFA, decreased omega-3 to omega-6 ratio, decreased percentage total PUFA, and decreased percentage omega-3 fatty acids in CO- compared with FO-finished heifers (P<0.05). Fatty acid profiles from intramuscular samples were ranked by the atherogenic index, and 20 heifers with either a high (HAI; n=10) or low (LAI; n=10) atherogenic index were selected for gene expression analysis using real-time PCR (RT-PCR). Gene expression data for the 20 individuals were analyzed as a 2 by 2 factorial arrangement of treatments using the GLM procedure in SAS. There was no significant diet × atherogenic index interaction identified for any gene (P>0.05). Upregulation was observed for PPARγ, fatty acid synthase (FASN), and fatty acid binding protein 4 (FABP4) in FO-finished compared with CO-finished heifers in both atherogenic index categories (P<0.05). Upregulation of diglyceride acyl transferase 2 (DGAT2) was observed in FO-finished heifers with a HAI (P<0.05). Expression of steroyl Co-A desaturase (SCD) was upregulated in CO-finished heifers with a LAI, and downregulated in FO-finished heifers with a HAI (P<0.05). Expression of adiponectin (ADIPOQ) was significantly downregulated in CO-finished heifers with a HAI compared with all other categories (P<0.05). The genes identified in this study which exhibit

Protocol for monitoring metals in Ozark National Scenic Riverways, Missouri: Version 1.0

USGS Publications Warehouse

Schmitt, Christopher J.; Brumbaugh, William G.; Besser, John M.; Hinck, Jo Ellen; Bowles, David E.; Morrison, Lloyd W.; Williams, Michael H.

2008-01-01

The National Park Service is developing a monitoring plan for the Ozark National Scenic Riverways in southeastern Missouri. Because of concerns about the release of lead, zinc, and other metals from lead-zinc mining to streams, the monitoring plan will include mining-related metals. After considering a variety of alternatives, the plan will consist of measuring the concentrations of cadmium, cobalt, lead, nickel, and zinc in composite samples of crayfish (Orconectes luteus or alternate species) and Asian clam (Corbicula fluminea) collected periodically from selected sites. This document, which comprises a protocol narrative and supporting standard operating procedures, describes the methods to be employed prior to, during, and after collection of the organisms, along with procedures for their chemical analysis and quality assurance; statistical analysis, interpretation, and reporting of the data; and for modifying the protocol narrative and supporting standard operating procedures. A list of supplies and equipment, data forms, and sample labels are also included. An example based on data from a pilot study is presented.

Effect of Blade-surface Finish on Performance of a Single-stage Axial-flow Compressor

NASA Technical Reports Server (NTRS)

Moses, Jason J; Serovy, George, K

1951-01-01

A set of modified NACA 5509-34 rotor and stator blades was investigated with rough-machine, hand-filed, and highly polished surface finishes over a range of weight flows at six equivalent tip speeds from 672 to 1092 feet per second to determine the effect of blade-surface finish on the performance of a single-stage axial-flow compressor. Surface-finish effects decreased with increasing compressor speed and with decreasing flow at a given speed. In general, finishing blade surfaces below the roughness that may be considered aerodynamically smooth on the basis of an admissible-roughness formula will have no effect on compressor performance.

Literature Survey on Weld-Metal Cracking

DTIC Science & Technology

1952-08-01

quench cracking in cast steel. A statistical investigation was made into the causes of quench cracking in low-alloy-steel gun tubes (FlZ). A definite...decreased with increased pouring temperature, finishing temperature, and forging reduction. Spretnak and Wells(F2O) also made a statistical analysis of...per cent to avoid hot cracks and fissures. Lee(I20) made a statistical study of the bead-cracking susceptibility of weld metal deposited with Type 307

Finisher hog production in the Southeastern United States: Ancillary measurements derived from the National Air Emissions Monitoring Study (NAEMS)

NASA Astrophysics Data System (ADS)

Robarge, W. P.; Lee, S.; Walker, J. T.

2010-12-01

Measurements of emissions of gases and fine particulate matter from swine animal feeding operations (AFOs) in the southeastern US have typically been confined to relatively short periods (days to several weeks) and have generally focused on waste lagoons. Access to swine animal housing units and other ancillary information has been limited. The National Air Emissions Monitoring Study (NAEMS) provided a unique opportunity to characterize emissions from swine housing units for an extended period of time (~ 2 years), and allowed access to ancillary measurements regarding nutrient flows (feed amounts and composition), manure dynamics, animal inventories, water usage and farm management. Presented here is a summary of the observations made for a NAEMS finisher site (NC3B) selected as being representative of swine production in the southeastern US. Finisher hogs are raised in rotations (~ 140 days) with a target market weight of 123 kg/hog. Among the population during a rotation (700-800 hogs/barn) the actual growth rate varies with a series of “grade-outs” of market-weight hogs starting ~ 110 days from initial load-in. Derivation of the standing live-weight in the barns during a rotation therefore requires use of a growth model and summation over several different “populations” of hogs within a single barn. Up to 5 different feed formulations are fed during a rotation with %N content ranging from (3.4 to 2.2% N; total feed consumed 181,000 kg/barn). Across 4 complete rotations, N consumed was ~50 g N per hog/day. Of this amount, we estimate ~ 60% is excreted as fecal matter and urine. The TAN (NH3 + NH4+) content of the shallow pits is consistently higher (1880 ±390 mg TAN/L) than that found in the anaerobic lagoon (800 ±70 mg TAN/L), except immediately after recharge following pit-pull (pH of the two liquids was similar). The presence of a recalcitrant layer of sludge in the shallow pits (liquid height = 20 cm; sludge depth = 5-10 cm; TAN = 2500 mg N/L; total

The Adolescent Who Does Not Finish Anything.

ERIC Educational Resources Information Center

Breiner, Sander J.

1985-01-01

Practical information for therapists who deal with adolescents who do not finish tasks is presented. The relationship of task incompletion to neurosis, psychosis, depression, homosexuality, and drug abuse is described, and techniques and guidelines for treatment are provided. (Author)

Biomachining: metal etching via microorganisms.

PubMed

Díaz-Tena, Estíbaliz; Barona, Astrid; Gallastegui, Gorka; Rodríguez, Adrián; López de Lacalle, L Norberto; Elías, Ana

2017-05-01

The use of microorganisms to remove metal from a workpiece is known as biological machining or biomachining, and it has gained in both importance and scientific relevance over the past decade. Conversely to mechanical methods, the use of readily available microorganisms is low-energy consuming, and no thermal damage is caused during biomachining. The performance of this sustainable process is assessed by the material removal rate, and certain parameters have to be controlled for manufacturing the machined part with the desired surface finish. Although the variety of microorganisms is scarce, cell concentration or density plays an important role in the process. There is a need to control the temperature to maintain microorganism activity at its optimum, and a suitable shaking rate provides an efficient contact between the workpiece and the biological medium. The system's tolerance to the sharp changes in pH is quite limited, and in many cases, an acid medium has to be maintained for effective performance. This process is highly dependent on the type of metal being removed. Consequently, the operating parameters need to be determined on a case-by-case basis. The biomachining time is another variable with a direct impact on the removal rate. This biological technique can be used for machining simple and complex shapes, such as series of linear, circular, and square micropatterns on different metal surfaces. The optimal biomachining process should be fast enough to ensure high production, a smooth and homogenous surface finish and, in sum, a high-quality piece. As a result of the high global demand for micro-components, biomachining provides an effective and sustainable alternative. However, its industrial-scale implementation is still pending.

The topographic development and areal parametric characterization of a stratified surface polished by mass finishing

NASA Astrophysics Data System (ADS)

Walton, Karl; Blunt, Liam; Fleming, Leigh

2015-09-01

Mass finishing is amongst the most widely used finishing processes in modern manufacturing, in applications from deburring to edge radiusing and polishing. Processing objectives are varied, ranging from the cosmetic to the functionally critical. One such critical application is the hydraulically smooth polishing of aero engine component gas-washed surfaces. In this, and many other applications the drive to improve process control and finish tolerance is ever present. Considering its widespread use mass finishing has seen limited research activity, particularly with respect to surface characterization. The objectives of the current paper are to; characterise the mass finished stratified surface and its development process using areal surface parameters, provide guidance on the optimal parameters and sampling method to characterise this surface type for a given application, and detail the spatial variation in surface topography due to coupon edge shadowing. Blasted and peened square plate coupons in titanium alloy are wet (vibro) mass finished iteratively with increasing duration. Measurement fields are precisely relocated between iterations by fixturing and an image superimposition alignment technique. Surface topography development is detailed with ‘log of process duration’ plots of the ‘areal parameters for scale-limited stratified functional surfaces’, (the Sk family). Characteristic features of the Smr2 plot are seen to map out the processing of peak, core and dale regions in turn. These surface process regions also become apparent in the ‘log of process duration’ plot for Sq, where lower core and dale regions are well modelled by logarithmic functions. Surface finish (Ra or Sa) with mass finishing duration is currently predicted with an exponential model. This model is shown to be limited for the current surface type at a critical range of surface finishes. Statistical analysis provides a group of areal parameters including; Vvc, Sq, and Sdq

Abrasive wear of resin composites as related to finishing and polishing procedures.

PubMed

Turssi, Cecilia P; Ferracane, Jack L; Serra, Mônica C

2005-07-01

Finishing and polishing procedures may cause topographical changes and introduce subsurface microcracks in dental composite restoratives. Since both of these effects may contribute toward the kinetics of wear, the purpose of this study was to assess and correlate the wear and surface roughness of minifilled and nanofilled composites finished and polished by different methods. Specimens (n=10) made of a minifilled and a nanofilled composite were finished and polished with one of the four sequences: (1) tungsten carbide burs plus Al(2)O(3)-impregnated brush (CbBr) or (2) tungsten carbide burs plus diamond-impregnated cup (CbCp), (3) diamond burs plus brush (DmBr) or (4) diamond burs plus cup (DmCp). As a control, abrasive papers were used. After surface roughness had been quantified, three-body abrasion was simulated using the OHSU wear machine. The wear facets were then scanned to measure wear depth and post-testing roughness. All sets of data were subjected to ANOVA and Tukey's tests (alpha=0.05). Pearson's correlation test was applied to check for the existence of a relationship between pre-testing roughness and wear. Significantly smoother surfaces were attained with the sequences CbBr and CbCp, whereas DmCp yielded the roughest surface. Regardless of the finishing/polishing technique, the nanofilled composite exhibited the lowest pre-testing roughness and wear. There was no correlation between the surface roughness achieved after finishing/polishing procedures and wear (p=0.3899). Nano-sized materials may have improved abrasive wear resistance over minifilled composites. The absence of correlation between wear and surface roughness produced by different finishing/polishing methods suggests that the latter negligibly influences material loss due to three-body abrasion.

Effects of finishing/polishing techniques on microleakage of resin-modified glass ilonomer cement restorations.

PubMed

Yap, Adrian U J; Yap, W Y; Yeo, Egwin J C; Tan, Jane W S; Ong, Debbie S B

2003-01-01

This study investigated the effect of finishing/polishing techniques on the microleakage of resin-modified glass ionomer restorations. Class V preparations were made on the buccal and lingual/palatal surfaces of freshly extracted teeth. The cavities on each tooth were restored with Fuji II LC (FT [GC]) and Photac-Fil Quick (PF [3M-ESPE]) according to manufacturers' instructions. Immediately after light-polymerization, gross finishing was done with eight-fluted tungsten carbide burs. The teeth were then randomly divided into four groups and finishing/polishing was done with one of the following systems: (a) Robot Carbides (RC); (b) Super-Snap system (SS); (c) OneGloss (OG) and (d) CompoSite Polishers (CS). The sample size for each material-finishing/polishing system combination was eight. After finishing/polishing, the teeth were stored in distilled water at 37 degrees C for one week. The root apices were then sealed with acrylic and two coats of varnish was applied 1 mm beyond the restoration margins. The teeth were subsequently subjected to dye penetration testing (0.5% basic fuchsin), sectioned and scored. Data was analyzed using Kruskal-Wallis and Mann-Whitney U tests at a significance level of 0.05. Results of statistical analysis were as follows: Enamel margins: PF-OGfinishing/polishing technique, leakage at dentin margins was significantly greater than at enamel margins for FT. For PF, no significant difference in leakage scores was observed between dentin and enamel with the exception of finishing/polishing with OG. FT restorations had significantly less enamel and dentin leakage than PF restorations when treated with OG. The effect of finishing/polishing techniques on microleakage was both tissue and material dependent.

Effect of finishing/polishing techniques and time on surface roughness of esthetic restorative materials.

PubMed

Madhyastha, Prashanthi Sampath; Hegde, Shreya; Srikant, N; Kotian, Ravindra; Iyer, Srividhya Sriraman

2017-01-01

Surface roughness associated with improper finishing/polishing of restorations can result in plaque accumulation, gingival irritation, surface staining, and poor esthetic of restored teeth. The study aimed to evaluate the efficiency of various finishing and polishing systems and time using various procedures on surface roughness of some esthetic restorative materials. In this in vitro study, samples of two composite materials, compomer and glass ionomer cement (GIC) materials, were fabricated. Finishing and polishing were done immediately ( n = 40) and after 1 week ( n = 40) using four systems (diamond bur + soflex discs; diamond bur + Astropol polishing brush; tungsten carbide bur + soflex discs; tungsten carbide bur + Astropol polishing brush). Surface roughness was measured using surface profilometer. Data were statistically analyzed by t -test (for each material and time period) and one-way analysis of variance followed by Tukey's post hoc (for finishing and polishing systems) at a significant level of P < 0.05. Analysis of time period, irrespective of finishing and polishing system showed that Ra values were greater ( P < 0.05) in delayed polishing in GIC > Z100 > Filtek P90 > Dyract AP, suggesting immediate polishing is better. Among the materials, Filtek P90 had the least Ra values indicating the smoothest surface among all materials, followed by Z100, Dyract AP, and GIC. Comparison of polishing and finishing systems irrespective of materials showed that Ra values were lower ( P > 0.05) in diamond + Astropol combination whereas diamond + soflex had the greatest Ra values. It might be concluded that: (i) Filtek P90 showed least Ra values followed by < Z100 < Dyract < GIC; (ii) immediate (24 h) finishing/polishing of materials is better than delayed; and (iii) among all these polishing systems, diamond bur-Astropol and Astrobrush showed good surface finish.

Distribution of Salmonella serovars in breeding, nursery, and grow-to-finish pigs, and risk factors for shedding in ten farrow-to-finish swine farms in Alberta and Saskatchewan.

PubMed

Wilkins, Wendy; Rajić, Andrijana; Waldner, Cheryl; McFall, Margaret; Chow, Eva; Muckle, Anne; Rosengren, Leigh

2010-04-01

The study objectives were to investigate Salmonella prevalence, serovar distribution, and risk factors for shedding in 10 purposively selected farrow-to-finish farms in Saskatchewan and Alberta. Pooled fecal samples from the breeding and grow-finish phases and individual fecal samples from breeding, nursery, and grow-finish pigs were cultured for Salmonella; serotyping of isolates was performed. Pig and pen characteristics were recorded for each pig and pen sampled.Overall, 407/1143 (36%) of samples were Salmonella positive; within-farm prevalence ranged from 1% to 79%. Sows, nursery, and grow-finish pigs accounted for 43%, 29%, and 28% of positive samples, respectively. More Salmonella were detected in pooled pen than individual pig samples (P < 0.001). Among 418 Salmonella isolates, there were 19 distinct serovars; the most common were S. Derby (28.5%), S. Typhimurium, var. Copenhagen (19.1%), S. Putten (11.8%), S. Infantis (6.8%), and S. Mbandaka (6.1%). Sows were more likely to shed Salmonella than nursery or grow-finisher (OR 2.9, P < 0.001) pigs. Pelleted feed (OR 8.2, P < 0.001) and nose-to-nose pig contact through pens (OR 2.2, P = 0.005) were associated with increased Salmonella prevalence. Significant differences in serovar distribution were detected among production phases. The use of pooled pen samples is recommended as a more efficient means for accurate evaluation of Salmonella status in different phases of pig production. The breeding herd might be an important source of Salmonella persistence within farrow-to-finish farms and should be targeted in control efforts. The latter might also apply to the use of pelleted feed, which remains the most consistently reported significant risk factor for Salmonella shedding in pigs.

SEM Evaluation of Surrounding Enamel after Finishing of Composite Restorations- Preliminary Results

NASA Astrophysics Data System (ADS)

Iovan, G.; Stoleriu, S.; Solomon, S.; Ghiorghe, A.; Sandu, A. V.; Andrian, S.

2017-06-01

The purpose of this study was to analyze the surface characteristics of the enamel adjacent to composite resin after finishing the restoration with different diamond and tungsten carbide burs. The topography of enamel was observed by using a scanning electron microscope. Finishing with extra-/ultra-fine carbide burs, and extra-fine diamond burs resulted in smooth surfaces. In few areas some superficial scratches with no clinical relevance were observed. Deep grooves were observed on the surface of enamel when fine diamond burs were used. Finishing of composite restorations with coarse burs should be avoided when there is a high risk of touching and scratching adjacent enamel during the procedure.

LEACHING OF METALS FROM HOUSEHOLD PLUMBING MATERIALS: IMPACT OF HOME WATER SOFTENERS

EPA Science Inventory

A pilot plant study was conducted to evaluate the effects of household ion exchange softening on the leaching of metals from home plumbing materials. The study was conducted in two phases on two different water qualities. Phase I was conducted using a finished tap water having a...

Thermal treatment of toxic metals of industrial hazardous wastes with fly ash and clay.

PubMed

Singh, I B; Chaturvedi, K; Morchhale, R K; Yegneswaran, A H

2007-03-06

Waste generated from galvanizing and metal finishing processes is considered to be a hazardous due to the presence of toxic metals like Pb, Cu, Cr, Zn, etc. Thermal treatment of such types of wastes in the presence of clay and fly ash can immobilizes their toxic metals to a maximum level. After treatment solidified mass can be utilized in construction or disposed off through land fillings without susceptibility of re-mobilization of toxic metals. In the present investigation locally available clay and fly ash of particular thermal power plant were used as additives for thermal treatment of both of the wastes in their different proportions at 850, 900 and 950 degrees C. Observed results indicated that heating temperature to be a key factor in the immobilization of toxic metals of the waste. It was noticed that the leachability of metals of the waste reduces to a negligible level after heating at 950 degrees C. Thermally treated solidified specimen of 10% waste and remaining clay have shown comparatively a higher compressive strength than clay fired bricks used in building construction. Though, thermally heated specimens made of galvanizing waste have shown much better strength than specimen made of metal finishing waste. The lechability of toxic metals like Cr, Cu, Pb and Zn became far below from their regulatory threshold after heating at 950 degrees C. Addition of fly ash did not show any improvement either in engineering property or in leachability of metals from the solidified mass. X-ray diffraction (XRD) analysis of the solidified product confirmed the presence of mixed phases of oxides of metals.

77 FR 12227 - Long Term 2 Enhanced Surface Water Treatment Rule: Uncovered Finished Water Reservoirs; Public...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-29

... Water Treatment Rule: Uncovered Finished Water Reservoirs; Public Meeting AGENCY: Environmental... review of the uncovered finished water reservoir requirement in the Long Term 2 Enhanced Surface Water... uncovered finished water reservoir requirement and the agency's Six Year Review process. EPA also plans to...

Wood properties affecting finish service life

Treesearch

R. Sam Williams; Charles Jourdain; George I. Daisey; Robert W. Springate

2000-01-01

Wood is a biological material that has widely different properties depending on species, geographic area where the tree grew, the growth conditions, size of the tree at harvest, sawing, and other manufacturing processes. Some of the more important wood properties as they relate to wood finishing are discussed, e.g., growth rate, density, knots, extractives, juvenile...

Effects of Wet and Dry Finishing and Polishing on Surface Roughness and Microhardness of Composite Resins

PubMed Central

Nasoohi, Negin; Hoorizad, Maryam

2017-01-01

Objectives: This study aimed to assess the effect of wet and dry finishing and polishing on microhardness and roughness of microhybrid and nanohybrid composites. Materials and Methods: Thirty samples were fabricated of each of the Polofil Supra and Aelite Aesthetic All-Purpose Body microhybrid and Grandio and Aelite Aesthetic Enamel nanohybrid composite resins. Each group (n=30) was divided into three subgroups of D, W and C (n=10). Finishing and polishing were performed dry in group D and under water coolant in group W. Group C served as the control group and did not receive finishing and polishing. Surface roughness of samples was measured by a profilometer and their hardness was measured by a Vickers hardness tester. Data were analyzed using two-way ANOVA (P<0.05). Results: The smoothest surfaces with the lowest microhardness were obtained under Mylar strip without finishing/polishing for all composites (P<0.0001). The highest surface roughness was recorded for dry finishing/polishing for all composites (P<0.0001). Dry finishing/polishing increased the microhardness of all composites (P<0.0001). Conclusions: Dry finishing and polishing increases the microhardness and surface roughness of microhybrid and nanohybrid composite resins. PMID:29104597

History of magnetorheological finishing

NASA Astrophysics Data System (ADS)

Harris, Daniel C.

2011-06-01

Magnetorheological finishing (MRF) is a deterministic method for producing complex optics with figure accuracy <50 nm and surface roughness <1 nm. MRF was invented at the Luikov Institute of Heat and Mass Transfer in Minsk, Belarus in the late 1980s by a team led by William Kordonski. When the Soviet Union opened up, New York businessman Lowell Mintz was invited to Minsk in 1990 to explore possibilities for technology transfer. Mintz was told of the potential for MRF, but did not understand whether it had value. Mintz was referred to Harvey Pollicove at the Center for Optics Manufacturing of the University of Rochester. As a result of their conversation, they sent Prof. Steve Jacobs to visit Minsk and evaluate MRF. From Jacobs' positive findings, and with support from Lowell Mintz, Kordonski and his colleagues were invited in 1993 to work at the Center for Optics Manufacturing with Jacobs and Don Golini to refine MRF technology. A "preprototype" finishing machine was operating by 1994. Prof. Greg Forbes and doctoral student Paul Dumas developed algorithms for deterministic control of MRF. In 1996, Golini recognized the commercial potential of MRF, secured investment capital from Lowell Mintz, and founded QED Technologies. The first commercial MRF machine was unveiled in 1998. It was followed by more advanced models and by groundbreaking subaperture stitching interferometers for metrology. In 2006, QED was acquired by and became a division of Cabot Microelectronics. This paper recounts the history of the development of MRF and the founding of QED Technologies.

24 CFR 200.946 - Building product standards and certification program for exterior finish and insulation systems...

Code of Federal Regulations, 2011 CFR

2011-04-01

... Glass Fiber Reinforcing Mesh for Use in Exterior Insulation and Finish Systems (EIFS), Class PB. (xv... certification program for exterior finish and insulation systems, use of Materials Bulletin UM 101. 200.946... product standards and certification program for exterior finish and insulation systems, use of Materials...

24 CFR 200.946 - Building product standards and certification program for exterior finish and insulation systems...

Code of Federal Regulations, 2010 CFR

2010-04-01

... Glass Fiber Reinforcing Mesh for Use in Exterior Insulation and Finish Systems (EIFS), Class PB. (xv... certification program for exterior finish and insulation systems, use of Materials Bulletin UM 101. 200.946... product standards and certification program for exterior finish and insulation systems, use of Materials...

National Center for Advanced Manufacturing Overview

NASA Technical Reports Server (NTRS)

Vickers, J.

2001-01-01

The National Center for Advanced Manufacturing (NCAM) is a strategy, organization, and partnership focused on long-term technology development. The NCAM initially will be a regional partnership, however the intent is national in scope. Benchmarking is needed to follow the concept to the finished project, not using trial and error. Significant progress has been made to date, and NCAM is setting the vision for the future.

Implementing Cleaner Printed Wiring Board Technologies: Surface Finishes

EPA Pesticide Factsheets

This document describes the problems, solutions, and time and effort involved in implementing alternative surface finish technologies, and this guide is produced as part of the DfE Printed Wiring Board Project

Surface Finish Effects Using Coating Method on 3D Printing (FDM) Parts

NASA Astrophysics Data System (ADS)

Haidiezul, AHM; Aiman, AF; Bakar, B.

2018-03-01

One of three-dimensional (3-D) printing economical processes is by using Fused Deposition Modelling (FDM). The 3-D printed object was built using layer-by-layer approach which caused “stair stepping” effects. This situation leads to uneven surface finish which mostly affect the objects appearance for product designers in presenting their models or prototypes. The objective of this paper is to examine the surface finish effects from the application of XTC-3D coating developed by Smooth-On, USA on the 3D printed parts. From the experimental works, this study shows the application of XTC-3D coating to the 3-D printed parts has improve the surface finish by reducing the gap between the layer

Performance, profitability and greenhouse gas emissions of alternative finishing strategies for Holstein-Friesian bulls and steers.

PubMed

Murphy, B; Crosson, P; Kelly, A K; Prendiville, R

2018-02-06

Modifying finishing strategies within established production systems has the potential to increase beef output and farm profit while reducing greenhouse gas (GHG) emissions. Thus, the objectives of this study were to investigate the effects of finishing duration on animal performance of Holstein-Friesian (HF) bulls and steers and evaluate the profitability and GHG emissions of these finishing strategies. A total of 90 HF calves were assigned to a complete randomised block design; three bull and three steer finishing strategies. Calves were rotationally grazed in a paddock system for the first season at pasture, housed and offered grass silage ad libitum plus 1.5 kg DM of concentrate per head daily for the first winter and returned to pasture for a second season. Bulls were slaughtered at 19 months of age and either finished indoors on concentrates ad libitum for 100 days (19AL), finished at pasture supplemented with 5 kg DM of concentrate per head daily for 100 (19SP) or 150 days (19LP). Steers were slaughtered at 21 months of age and finished at pasture, supplemented with 5 kg DM of concentrate per head daily for 60 (21SP) and 110 days (21LP) or slaughtered at 24 months of age and finished indoors over the second winter on grass silage ad libitum plus 5 kg DM of concentrate per head daily (24MO). The Grange Dairy Beef Systems Model and the Beef Systems Greenhouse Gas Emissions Model were used to evaluate profitability and GHG emissions, respectively. Average daily gain during the finishing period (P<0.001), live weight at slaughter (P<0.01), carcass weight (P<0.05) and fat score (P<0.001) were greater for 19AL than 19SP and 19LP, respectively. Similarly, concentrate dry matter intake was greater for 19AL than 19SP; 19LP was intermediate (P<0.001). Live weight at slaughter (P<0.001), carcass weight (P<0.001), conformation score (P<0.05) and fat score (P<0.001) were greater for 24MO than 21SP and 21LP, respectively. During the finishing period concentrate dry matter

40 CFR 425.10 - Applicability; description of the hair pulp, chrome tan, retan-wet finishing subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Applicability; description of the hair... FINISHING POINT SOURCE CATEGORY Hair Pulp, Chrome Tan, Retan-Wet Finish Subcategory § 425.10 Applicability; description of the hair pulp, chrome tan, retan-wet finishing subcategory. The provisions of this subpart are...

40 CFR 425.10 - Applicability; description of the hair pulp, chrome tan, retan-wet finishing subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false Applicability; description of the hair... FINISHING POINT SOURCE CATEGORY Hair Pulp, Chrome Tan, Retan-Wet Finish Subcategory § 425.10 Applicability; description of the hair pulp, chrome tan, retan-wet finishing subcategory. The provisions of this subpart are...

40 CFR 425.20 - Applicability; description of the hair save, chrome tan, retan-wet finish subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Applicability; description of the hair... FINISHING POINT SOURCE CATEGORY Hair Save, Chrome Tan, Retan-Wet Finish Subcategory § 425.20 Applicability; description of the hair save, chrome tan, retan-wet finish subcategory. The provisions of this subpart are...

40 CFR 425.10 - Applicability; description of the hair pulp, chrome tan, retan-wet finishing subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Applicability; description of the hair... FINISHING POINT SOURCE CATEGORY Hair Pulp, Chrome Tan, Retan-Wet Finish Subcategory § 425.10 Applicability; description of the hair pulp, chrome tan, retan-wet finishing subcategory. The provisions of this subpart are...

40 CFR 425.20 - Applicability; description of the hair save, chrome tan, retan-wet finish subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Applicability; description of the hair... FINISHING POINT SOURCE CATEGORY Hair Save, Chrome Tan, Retan-Wet Finish Subcategory § 425.20 Applicability; description of the hair save, chrome tan, retan-wet finish subcategory. The provisions of this subpart are...

40 CFR 425.20 - Applicability; description of the hair save, chrome tan, retan-wet finish subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false Applicability; description of the hair... FINISHING POINT SOURCE CATEGORY Hair Save, Chrome Tan, Retan-Wet Finish Subcategory § 425.20 Applicability; description of the hair save, chrome tan, retan-wet finish subcategory. The provisions of this subpart are...

Comparative evaluation of different thermally modified wood samples finishing with UV-curable and waterborne coatings

NASA Astrophysics Data System (ADS)

Herrera, René; Muszyńska, Monika; Krystofiak, Tomasz; Labidi, Jalel

2015-12-01

Thermally modified wood has been developed as an industrial method to improve durability and dimensional stability of wood and thus extends the range of uses and service life of wood-based products. Despite the improvements gained by treatment, surface finishing using coatings prevents esthetical changes such as color degradation or occasional growth of mold adding protection in outdoor use and extending the service life of products. The wood finishing process was carried out with commercially available waterborne and UV-curable coatings on industrially modified at 192, 200, 212 °C and unmodified European ash (Fraxinus excelsior L.) wood, using an industrial rollers system and a laboratory brushing system. Changes caused by thermal treatment which could affect the surface finish were measured and compared with control samples, such as water uptake, wettability and acidity. Following the wood finishing, surface properties and esthetic changes were evaluated; as well as the coatings performance. Thermally modified wood presented improved adherence compared with unmodified wood with a significant improvement in samples modified at 212 °C, which also present the highest hardness when UV-cured. Finishes with UV-curing maintain the hydrophobic effect of thermally modified wood, whereas waterborne finishes increase the surface wettability. Thermal modification did not negatively influence on the elastic properties of the coated substrate and thus allows this material to be finished with different coating systems in the same conditions as unmodified wood.

The Effectiveness of Finishing School Programmes from the Perspectives of Graduates and Employers

ERIC Educational Resources Information Center

Ali, Jamal; Eam, Lim Hock; Ismail, Russayani; Rahim, Fauziah Abdul; Isa, Filzah Md; Ismail, Ismi Arif

2014-01-01

Purpose: This study examined the effectiveness of Finishing School programmes in enhancing the employability of graduates from institutions of higher learning. The perceptions of the graduates and employers towards the effectiveness of the programmes were analyzed. The effectiveness of Finishing School programmes evaluated through a graduate…

Use of Optical Mapping in Bacterial Genome Finishing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Dibyendu

2010-06-03

Dibyendu Kumar from the University of Florida discusses whole-genome optical mapping to help validate bacterial genome assemblies on June 3, 2010 at the "Sequencing, Finishing, Analysis in the Future" meeting in Santa Fe, NM.

Influence of finishing systems on hydrophilic and lipophilic oxygen radical absorbance capacity (ORAC) in beef.

PubMed

Wu, C; Duckett, S K; Neel, J P S; Fontenot, J P; Clapham, W M

2008-11-01

The aim of this research was to: (1) develop a reliable extraction procedure and assay to determine antioxidant activity in meat products, and (2) assess the effect of beef finishing system (forage-finished: alfalfa, pearl millet or mixed pastures vs. concentrate-finished) on longissimus muscle antioxidant activity. The effect of extraction method (ethanol concentration and extraction time), protein removal, and sample preparation method (pulverization or freeze drying) were first evaluated to develop an antioxidant assay for meat products. Beef extracts prepared with low ethanol concentrations (20%) demonstrated higher hydrophilic ORAC. Protein removal prior to extraction reduced hydrophilic ORAC values. Sample preparation method influenced both hydrophilic and lipophilic ORAC, with pulverized samples containing higher hydrophilic and lipophilic ORAC values. Beef cattle finishing system (Forage: alfalfa, pearl millet, or natural pasture vs. concentrates) had little impact on muscle hydrophilic ORAC, but muscle from forage finished beef contained greater lipophilic ORAC. In addition, broiling of steaks reduced hydrophilic ORAC.

Characterisation of the joining zone of serially arranged hybrid semi-finished components

NASA Astrophysics Data System (ADS)

Behrens, B.-A.; Chugreev, A.; Matthias, T.

2018-05-01

Forming of already joined semi-finished products is an innovative approach to manufacture components which are well-adapted to external loads. This approach results in an economically and ecologically improved production by the targeted use of high-quality materials in component areas, which undergo high stresses. One possible production method for hybrid semi-finished products is friction welding. This welding method allows for the production of hybrid semi-finished products made of aluminium and steel as well as steel and steel. In this paper, the thermomechanical tensile and shear stresses causing a failure of the joined zone are experimentally determined through tension tests. These tests are performed with specimens whose joint zones are aligned with different angles to the load direction.

Preparation of Nucleic Acid Libraries for Personalized Sequencing Systems Using an Integrated Microfluidic Hub Technology (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)

ScienceCinema

Patel, Kamlesh D.

2018-01-22

Kamlesh (Ken) Patel from Sandia National Laboratories (Livermore, California) presents "Preparation of Nucleic Acid Libraries for Personalized Sequencing Systems Using an Integrated Microfluidic Hub Technology " at the 7th Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting held in June, 2012 in Santa Fe, NM.

Preparation of Nucleic Acid Libraries for Personalized Sequencing Systems Using an Integrated Microfluidic Hub Technology (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patel, Kamlesh D.

2012-06-01

Kamlesh (Ken) Patel from Sandia National Laboratories (Livermore, California) presents "Preparation of Nucleic Acid Libraries for Personalized Sequencing Systems Using an Integrated Microfluidic Hub Technology " at the 7th Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting held in June, 2012 in Santa Fe, NM.

Stormwater Pollution Prevention Plan for the TA-03-38 Metals Fabrication Shop, Los Alamos National Laboratory, Revision 3, January 2018

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burgin, Jillian Elizabeth

This Storm Water Pollution Prevention Plan (SWPPP) was developed in accordance with the provisions of the Clean Water Act (33 U.S.C. §§1251 et seq., as amended), and the Multi-Sector General Permit for Storm Water Discharges Associated with Industrial Activity (U.S. EPA, June 2015) issued by the U.S. Environmental Protection Agency (EPA) for the National Pollutant Discharge Elimination System (NPDES) and using the industry specific permit requirements for Sector AA-Fabricated Metal Products as a guide. This SWPPP applies to discharges of stormwater from the operational areas of the TA-03-38 Metals Fabrication Shop at Los Alamos National Laboratory. Los Alamos National Laboratorymore » (also referred to as LANL or the “Laboratory”) is owned by the Department of Energy (DOE), and is operated by Los Alamos National Security, LLC (LANS). Throughout this document, the term “facility” refers to the TA-03-38 Metals Fabrication Shop and associated areas. The current permit expires at midnight on June 4, 2020.« less

Trace elements and heavy metals in the Grand Bay National Estuarine Reserve in the northern Gulf of Mexico

USDA-ARS?s Scientific Manuscript database

The Grand Bay National Estuarine Research Reserve has the highest biotic diversity of habitats and offer a reserve of food resources and commercially significant species. Rapid human civilization has led to accumulation of heavy metals and trace elements in estuaries. The Grand Bay National Estuarin...

Evidence for spontaneous retrieval of suspended but not finished prospective memories.

PubMed

Scullin, Michael K; Einstein, Gilles O; McDaniel, Mark A

2009-06-01

McDaniel and Einstein (2007) argued that prospective memories can be retrieved through spontaneous retrieval processes stimulated by the presence of a target cue. To test this claim, we investigated whether presenting a prospective memory cue during a task that did not require an intention to be performed spontaneously triggered remembering of that intention. In two experiments, participants performed an image-rating task in which a prospective memory task (to press the "Q" key when a target word appeared) was embedded. Then, participants were told that their intention was finished or suspended. Finally, participants performed a lexical decision task in which each target (and a matched control) word appeared. RTs were slower to target words than to control words when the intention was suspended but not when it was finished. These results suggest that target cues associated with suspended intentions can spontaneously trigger remembering but that finished intentions are quickly deactivated.

Finishing of additively manufactured titanium alloy by shape adaptive grinding (SAG)

NASA Astrophysics Data System (ADS)

Beaucamp, Anthony T.; Namba, Yoshiharu; Charlton, Phillip; Jain, Samyak; Graziano, Arthur A.

2015-06-01

In recent years, rapid prototyping of titanium alloy components for medical and aeronautics application has become viable thanks to advances in technologies such as electron beam melting (EBM) and selective laser sintering (SLS). However, for many applications the high surface roughness generated by additive manufacturing techniques demands a post-finishing operation to improve the surface quality prior to usage. In this paper, the novel shape adaptive grinding process has been applied to finishing titanium alloy (Ti6Al4V) additively manufactured by EBM and SLS. It is shown that the micro-structured surface layer resulting from the melting process can be removed, and the surface can then be smoothed down to less than 10 nm Ra (starting from 4-5 μm Ra) using only three different diamond grit sizes. This paper also demonstrates application of the technology to freeform shapes, and documents the dimensional accuracy of finished artifacts.

Metal hydride reasearch and development program at Brookhaven National Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, J.R.; Reilly, J.J.

1978-01-01

A progress report is presented covering work performed in the hydrogen materials development program at Brookhaven National Laboratory (BNL) for FY78 which encompasses the time period from October 1, 1977 through September 30, 1978. The subjects to be discussed here concern properties of importance in the utilization of metal hydrides as energy storage media. Most of the areas of research were initiated prior to FY78, however all of the results contained in this manuscript were obtained during the aforementioned period of time. The following subjects will be discussed: the properties of ferro-titanium and chrome-titanium alloy hydrides.

Effects of forage species or concentrate finishing on animal performance, carcass and meat quality.

PubMed

Duckett, S K; Neel, J P S; Lewis, R M; Fontenot, J P; Clapham, W M

2013-03-01

Angus-cross steers (n = 128; initial BW = 270 ± 3.8 kg) were used in a 3-yr study to assess effects of forage species grazed before slaughter versus concentrate finishing on carcass and meat quality. At the completion of the stockering phase, steers were randomly allotted to mixed pasture (MP; n = 36/yr) or corn-silage concentrate (CON; n = 12/yr) finishing treatments. At 40 d before harvest, MP steers were randomly divided into 3 forage species treatments: alfalfa (AL), pearl millet (PM), or mixed pasture (MP). Average daily BW gain was greater (P = 0.001) for CON than for forage-finished (FOR) steers during the early and overall finishing phase. During the late finishing phase when FOR steers were grazing difference forage species, ADG was greater (P = 0.03) for PM than MP or AL. Harvest weight and HCW were greater (P < 0.001) for CON than FOR due to the differences in animal performance. Total fat percentage of the 9th to 11th rib section was 46% less(P = 0.028) for FOR than CON due to reductions (P < 0.001) in the percentage of subcutaneous fat. Warner-Bratzler shear force (WBS) values at 14 d and 28 d of aging did not differ (P > 0.78) between CON and FOR and were not altered (P > 0.40) by forage species. Trained sensory panel juiciness, initial tenderness, and overall tenderness scores did not differ (P > 0.17) by finishing treatment or forage species. Beef flavor intensity was greater (P < 0.001) for CON than FOR. Beef flavor intensity was greater (P < 0.02) for AL and PM than MP. Off-flavor intensity was greater (P < 0.001) for all forage-fed steaks, regardless of forage species, than CON. Finishing on forages reduced (P = 0.003) total lipid content by 61% for the LM compared with CON finished cattle. Forage species grazed before harvest did not alter (P > 0.05) total lipid content of the LM. Oleic acid concentration and total MUFA of the LM were 21% and 22% less (P = 0.001) for FOR than CON. Concentrations of all individual [linolenic acid

Flame retardant finishing of cotton fabric based on synergistic compounds containing boron and nitrogen.

PubMed

Xie, Kongliang; Gao, Aiqin; Zhang, Yongsheng

2013-10-15

Boric acid and compound containing nitrogen, 2,4,6-tri[(2-hydroxy-3-trimethyl-ammonium)propyl]-1,3,5-triazine chloride (Tri-HTAC) were used to finish cotton fabric. The flame retardant properties of the finished cotton fabrics and the synergetic effects of boron and nitrogen elements were investigated and evaluated by limited oxygen index (LOI) method. The mechanism of cross-linking reaction among cotton fiber, Tri-HTAC, and boric acid was discussed by FTIR and element analysis. The thermal stability and surface morphology of the finished cotton fabrics were investigated by thermogravimetric analysis (TGA) and scanning electron microscope (SEM), respectively. The finishing system of the mixture containing boron and nitrogen showed excellent synergistic flame retardancy for cotton fabric. The cotton fabric finished with mixture system had excellent flame retardancy. The LOI value of the treated cotton fabric increased over 27.5. Tri-HTAC could form covalent bonds with cellulose fiber and boric acid. The flame retardant cotton fabric showed a slight decrease in tensile strength and whiteness. The surface morphology of flame retardant cotton fiber was smooth. Copyright © 2013 Elsevier Ltd. All rights reserved.

Drywall Finishing Apprenticeship. Course Outline (C-6).

ERIC Educational Resources Information Center

Lengert, Gerald

This course outline was prepard to help apprentice drywall installers and teachers of drywall finishing courses to learn or teach the skills necessary for the apprenticeship course in British Columbia. The course outline consists of 11 tracks (units) that cover the following topics: estimating, job inspection, safety, applying bead, filling…

Evaluation of the chelating performance of biopolyelectrolyte green complexes (NIBPEGCs) for wastewater treatment from the metal finishing industry.

PubMed

López-Maldonado, Eduardo A; Zavala García, Oscar Gabriel; Escobedo, Kevin Cruz; Oropeza-Guzman, Mercedes T

2017-08-05

In this paper nonstoichiometric interbiopolyelectrolyte green complexes (NIBPEGCs) were prepared using chitosan (Ch), alginate (AG) and poly(acrylic acid)(PAA). They are proposed as innovative formulations (polyelectrolytes and chelating agents) suitable for the elimination heavy metals contained in wastewater. This application may represent an integral solution for industries rejecting solid and aqueous metallic materials; however, it has not been previously reported. NIBPEGCs physicochemical performance was evaluated based on pH, particle size, surface charge, isoelectric point, dose, coagulation-flocculation kinetics and chemical affinity with seven metal ions. The experimental results showed that NIBPEGCs composed by AG/Ch and PAA/Chitosan have all the three complementary functions: chemical affinity, electrostatic interaction and particle entrapment anticipating more simple operation units to remove heavy metals. Complexes of AG/Ch (negative) were higher performance in removing heavy metals, with a dose window (150-180mg/L), lower dose of 410mg/L PAA/Ch (negative). Investigation of chelating performances of NIBPEGCs show that the efficiency of metal removal is: Ca˃Cr˃Cu˃Pb˃Ni˃Zn˃Cd. Transmittance vs time profiles, metals and zeta potential analysis showed that chelation capacity is the crucial factor to ensure metallic species removal, followed by physical entrapment of the metallic colloids. Integrating all presented results allow to sustain the development of excellent metals removal formulations. Copyright © 2017 Elsevier B.V. All rights reserved.

Portable flooring protects finished surfaces, is easily moved

NASA Technical Reports Server (NTRS)

Carmody, R. J.

1964-01-01

To protect curved, finished surface and provide support for workmen, portable flooring has been made from rigid plastic foam blocks, faced with aluminum strips. Held together by nylon webbing, the flooring can be rolled up for easy carrying.

Surface Finish and Residual Stresses Induced by Orthogonal Dry Machining of AA7075-T651

PubMed Central

Jomaa, Walid; Songmene, Victor; Bocher, Philippe

2014-01-01

The surface finish was extensively studied in usual machining processes (turning, milling, and drilling). For these processes, the surface finish is strongly influenced by the cutting feed and the tool nose radius. However, a basic understanding of tool/surface finish interaction and residual stress generation has been lacking. This paper aims to investigate the surface finish and residual stresses under the orthogonal cutting since it can provide this information by avoiding the effect of the tool nose radius. The orthogonal machining of AA7075-T651 alloy through a series of cutting experiments was performed under dry conditions. Surface finish was studied using height and amplitude distribution roughness parameters. SEM and EDS were used to analyze surface damage and built-up edge (BUE) formation. An analysis of the surface topography showed that the surface roughness was sensitive to changes in cutting parameters. It was found that the formation of BUE and the interaction between the tool edge and the iron-rich intermetallic particles play a determinant role in controlling the surface finish during dry orthogonal machining of the AA7075-T651 alloy. Hoop stress was predominantly compressive on the surface and tended to be tensile with increased cutting speed. The reverse occurred for the surface axial stress. The smaller the cutting feed, the greater is the effect of cutting speed on both axial and hoop stresses. By controlling the cutting speed and feed, it is possible to generate a benchmark residual stress state and good surface finish using dry machining. PMID:28788534

A novel approach of magnetorheological abrasive fluid finishing with swirling-assisted inlet flow

NASA Astrophysics Data System (ADS)

Kheradmand, Saeid; Esmailian, Mojtaba; Fatahy, A.

Abrasive flow machining has been the pioneer of new finishing processes. Rotating workpiece and imposing a magnetic field using magnetorheological working medium are some assisting manipulations to improve surface finishing, because they can increase the forces on the workpiece surface. Similarly, swirling the inlet flow using stationary swirler vanes, as a novel idea, may also increase forces on the surface, and then raise the material removal, with a lower expense and energy consumption compared with the case of workpiece rotation. Thus, in this paper, surface roughness improvement is studied in a pipe with rotating inlet flow of a magnetorheological finishing medium under imposing a magnetic field. The results are compared with the case of rotating workpiece, using 3D numerical simulation. The governing hydrodynamic parameters are investigated in both cases to monitor the flow variations. It is shown that surface roughness is improved by rotating inlet flow. However, it is found that finishing in the entrance length of swirling-assisted inlet flow can be so economical for short length workpieces, compared with the case of rotating workpiece, with very near Ra values. By comparison of the numerical results and published experimental data, current study also shows the ability of the numerical simulation, as an inexpensive and efficient tool, to predict the surface roughness changes in finishing processes.

Index selection in terminal sires improves lamb performance at finishing.

PubMed

Márquez, G C; Haresign, W; Davies, M H; Roehe, R; Bünger, L; Simm, G; Lewis, R M

2013-01-01

Lamb meat is often perceived by consumers as fatty, and consumption has decreased in recent decades. A lean growth index was developed in the UK for terminal sire breeds to increase carcass lean content and constrain fat content at a constant age end point. The purposes of this study were 1) to evaluate the effects of index selection of terminal sires on their crossbred offspring at finishing and 2) to evaluate its effectiveness within terminal sire breeds. Approximately 70% of lambs marketed in the UK have been sired by rams of breeds typically thought of as specialized terminal sires. The most widely used are Charollais, Suffolk, and Texel. These breeds participated in sire referencing schemes from the early 1990s by sharing rams among flocks selected on the lean growth index. From 1999 to 2002 approximately 15 "high" and 15 "low" lean growth index score rams were selected from within their sire referencing schemes and mated to Welsh and Scottish Mule ewes. Their crossbred offspring were commercially reared on 3 farms in the UK. Lambs were finished to an estimated 11% subcutaneous fat by visual evaluation. At finishing, lambs were weighed, ultrasonically scanned, and assessed for condition score and conformation. Records were obtained for 6356 lambs on finishing BW (FWT), ultrasonic muscle depth (UMD), ultrasonic fat depth, overall condition score (OCS), and conformation of gigot, loin, and shoulder. Ultrasonic fat depth was log transformed (logUFD) to approach normality. High-index-sired lambs were heavier at finishing (1.2±0.2 kg) with thicker UMD (0.7±0.2 mm) and less logUFD (0.08±0.01 mm; P<0.05). There were no differences in OCS or conformation based on the sire index or breed (P>0.08). Suffolk-sired lambs were heavier than Charollais (1.0±0.3 kg), which were heavier than Texel (0.9±0.3 kg; P<0.001). Texel-sired lambs had thicker UMD than Charollais (0.7±0.2 mm; P<0.001) but were not different than Suffolk. Charollais-sired lambs had greater log

PICKLEX AS A NON-POLLUTING METAL SURFACE FINISHING PRETREATMENT AND PRETREATMENT/CONVERSION COATING

EPA Science Inventory

The effectiveness of a zirconium dioxide (ZrO2) membrane filter was evaluated for recycling a nonionic aqueous metal cleaning bath under real world conditions. The pilot-scale study consisted of four 7-to16-day filtration runs, each processed a portion of the cleaning bath during...

Chemical fractionation of metals in wetland sediments: Indiana Dunes National Lakeshore.

PubMed

Dollar, N L; Souch, C J; Filippelli, G M; Mastalerz, M

2001-09-15

Tessier-type (1979) sequential extractions for heavy metals (Cd, Cr, Cu, Fe, Mn, Pb, and Zn) were conducted on sediments from two wetland sites, one inundated and the other drained, within the Indiana Dunes National Lakeshore (IDNL), NW Indiana, with the objective of (i) evaluating extraction techniques on organic-rich sediments, (ii) determining the geochemistry and mobility of potentially biotoxic trace metals in a contaminated environment, and (iii) considering the implications of different restoration strategies on the potential for heavy metal remobilization. Long and repeated extractions were needed to effectively degrade the organic-rich sediments (up to 75% of the sediment by mass). Analysis of sulfur fractionation revealed that it was predominantly sequestered along with the organically bound fraction (renamed oxidizable). Metal recovery was good with the sum of the extractant steps typically within 20% of the total metal concentration determined after total microwave digestion. Results showed metal fractionation to be both metal- and site-specific, The oxidizable fraction is dominant for Cu, Cr, and Fe (>65% of the nonresidual fraction for almost all samples) and overall is most important also for Cd and Pb. The iron/manganese oxide fraction is important for Pb, Mn, and Zn, particularly at the drained site. The carbonate bound fraction is relatively insignificant at both sites, except for Cd and Mn, although it is more important at the drained site. The exchangeable fraction is significant in the uppermost sediments at the drained site, particularly for Cd (3-24%), Pb (3-14%), and Zn (36-45%); whereas, for the inundated site, it ranged only from 0 to 1% Zn, with no detectable Cd or Pb. Chromium, Cu, and Fe exist in forms not likely to be remobilized, whereas Cd, Mn, Pb, and Zn are potentially mobile if drained wetland sites are reflooded (and pH and redox potential altered). Simple mass balance calculations illustrate the potential for the removal of

Surface texture of resin-modified glass ionomer cements: effects of finishing/polishing systems.

PubMed

Yap, Adrian U J; Tan, W S; Yeo, J C; Yap, W Y; Ong, S B

2002-01-01

This study investigated the surface texture of two resin-modified glass ionomer cements (RMGICs) in the vertical and horizontal axis after treatment with different finishing/polishing systems. Class V preparations were made on the buccal and lingual/palatal surfaces of freshly extracted teeth. The cavities on each tooth were restored with Fuji II LC (GC) and Photac-Fil Quick (ESPE) according to manufacturers' instructions. Immediately after light-polymerization, gross finishing was done with 8-flute tungsten carbide burs. The teeth were then randomly divided into four groups and finished/polished with (a) Robot Carbides (RC); (b) Super-Snap system (SS); (c) OneGloss (OG) and (d) CompoSite Points (CS). The sample size for each material-finishing/polishing system combination was eight. The mean surface roughness (microm) in vertical (RaV) and horizontal (RaH) axis was measured using a profilometer. Data was subjected to ANOVA/Scheffe's tests and Independent Samples t-test at significance level 0.05. Mean RaV ranged from 0.59-1.31 and 0.83-1.52, while mean RaH ranged from 0.80-1.43 and 0.85-1.58 for Fuji II LC and Photac-Fil, respectively. Results of statistical analysis were as follows: Fuji II LC: RaV-RC, SSfinished with RC. The use of carbides (RC) and one-step rubber abrasive system (OG) for finishing/polishing of RMGICs is not recommended. Graded abrasive disk (SS) or two-step rubber abrasive (CS) systems should be used instead.

Evaluation of marginal fit of two all-ceramic copings with two finish lines

PubMed Central

Subasi, Gulce; Ozturk, Nilgun; Inan, Ozgur; Bozogullari, Nalan

2012-01-01

Objectives: This in-vitro study investigated the marginal fit of two all-ceramic copings with 2 finish line designs. Methods: Forty machined stainless steel molar die models with two different margin designs (chamfer and rounded shoulder) were prepared. A total of 40 standardized copings were fabricated and divided into 4 groups (n=10 for each finish line-coping material). Coping materials tested were IPS e.max Press and Zirkonzahn; luting agent was Variolink II. Marginal fit was evaluated after cementation with a stereomicroscope (Leica MZ16). Two-way analysis of variance and Tukey-HSD test were performed to assess the influence of each finish line design and ceramic type on the marginal fit of 2 all-ceramic copings (α =.05). Results: Two-way analysis of variance revealed no statistically significant differences for marginal fit relative to finish lines (P=.362) and ceramic types (P=.065). Conclusion: Within the limitations of this study, both types of all-ceramic copings demonstrated that the mean marginal fit was considered acceptable for clinical application (⩽120 μm). PMID:22509119

Hot metal gas forming of titanium grade 2 bent tubes

NASA Astrophysics Data System (ADS)

Paul, Alexander; Werner, Markus; Trân, Ricardo; Landgrebe, Dirk

2017-10-01

Within the framework of investigations, an exhaust gas component made of Titanium Grade 2 was produced by means of Hot Metal Gas Forming (HMGF) at the Fraunhofer IWU in Chemnitz, Germany. The semi-finished products were two-fold bent, thermal joined, calibrated and pre-formed tubes. So far, a three-stage internal high-pressure forming process at room temperature plus two necessary intermediate heat treatments were used to produce the component. Due to its complexity as well as the limited forming ability of Titanium Grade 2 at room temperature an one step Hot Metal Gas Forming was developed to replace the former procedure.

40 CFR 63.5395 - How do I measure the density of a finish?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 13 2013-07-01 2012-07-01 true How do I measure the density of a... and Initial Compliance Requirements § 63.5395 How do I measure the density of a finish? (a) To determine the density of a finish, the reference method is EPA Method 24 of appendix A of 40 CFR part 60...

40 CFR 63.5395 - How do I measure the density of a finish?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 13 2014-07-01 2014-07-01 false How do I measure the density of a... and Initial Compliance Requirements § 63.5395 How do I measure the density of a finish? (a) To determine the density of a finish, the reference method is EPA Method 24 of appendix A of 40 CFR part 60...

40 CFR 63.5395 - How do I measure the density of a finish?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 13 2012-07-01 2012-07-01 false How do I measure the density of a... and Initial Compliance Requirements § 63.5395 How do I measure the density of a finish? (a) To determine the density of a finish, the reference method is EPA Method 24 of appendix A of 40 CFR part 60...

UV-light assisted patterned metallization of textile fabrics

NASA Astrophysics Data System (ADS)

Bahners, Thomas; Gebert, Beate; Prager, Andrea; Hartmann, Nils; Hagemann, Ulrich; Gutmann, Jochen S.

2018-04-01

A UV-assisted process allows full-faced or local deposition of silver domains on textiles made of natural as well as synthetic fibers, which act as nuclei for subsequent galvanic metallization. SEM and XPS analyses indicate that the process generates particulate depositions - particles, aggregates - of elementary silver. Masking the UV irradiation confines silver deposition strictly to the exposed areas thus allowing patterning. Adhesion of the deposited silver is high on the studied natural fiber cotton and polyamide fibers. Adhesion on smooth and chemically inert synthethic fibers such as, e.g., poly(ethylene terephthalate) or para- and meta-aramids could be enhanced by finishing with poly(vinylamine) thus providing complex-forming amino groups. Although the process does not deposit a closed, electrically conducting layer, all studied samples could be metallized by galvanization. The resulting metal coatings exhibit high conductivity and wash stability. Following a patterned silver deposition, the subsequent galvanic metallization produced conductive patterns of identical geometry thus opening an avenue towards printed circuits on textile fabrics.

Evaluation of Some Finishing Properties of Oil Palm Particleboard for Furniture Application

NASA Astrophysics Data System (ADS)

Ratnasingam, J.; Nyugen, V.; Ioras, F.

The finishing properties of particleboard made from the Empty-Fruit Bunch (EFB) of oil palm (Elaeis guineensis Jacq.) were evaluated for its suitability for furniture applications, using different coating and overlay materials. The results found that the thick plastic-formica overlay provided the best surface finish, in terms of surface smoothness, adhesion strength and impact resistance. Although the polyurethane lacquer provided an acceptable finish, its quality and performance is not comparable to that of the thick plastic overlay. Despite the fact that the use of such overlay material may render the material not aesthetically appealing and limit it to concealed applications or where the thick overlay material is tolerated, its cost competitiveness and environmental friendliness may be able to position the oil palm particleboard as a substitute for the conventional wood-based particleboard in the furniture manufacturing industry.

Meat goat kids finished on alfalfa, red clover or orchardgrass pastures: carcass merit and meat quality.

PubMed

Turner, K E; Cassida, K A; Zerby, H N

2014-12-01

This experiment was conducted in 2005-2007 to evaluate carcass and chevon (goat meat) quality parameters when meat-goat kids (n=72) were finished on alfalfa (Medicago sativa L; ALF); red clover (Trifolium pratense L.; RCG); or orchardgrass (Dactylis glomerata L.; OGR) pastures. Carcass conformation score was greater (P=0.08) when meat-goat kids were finished on ALF compared to OGR with RCG intermediate. Chevon meat samples from goats finished on the three pasture treatments did not differ in ash, intramuscular fat, or crude protein content or in concentrations of omega6 and omega3 fatty acids, or the omega6 to omega3 ratio. Goats finished on OGR had higher (P<0.001) 18:1 trans-11 fatty acids (FA) compared to ALF or RCG. Overall, meat-goat kids finished on ALF, RCG, or ORG produced desirable carcass weights for most niche markets in the USA. Chevon is a low-fat meat option with high desirable fatty acids for human diets. Published by Elsevier Ltd.

Optimal Magnetorheological Fluid for Finishing of Chemical-Vapor-Deposited Zinc Sulfide

NASA Astrophysics Data System (ADS)

Salzman, Sivan

Magnetorheological finishing (MRF) of polycrystalline, chemical-vapor- deposited zinc sulfide (ZnS) optics leaves visible surface artifacts known as "pebbles". These artifacts are a direct result of the material's inner structure that consists of cone-like features that grow larger (up to a few millimeters in size) as deposition takes place, and manifest on the top deposited surface as "pebbles". Polishing the pebble features from a CVD ZnS substrate to a flat, smooth surface to below 10 nm root-mean-square is challenging, especially for a non-destructive polishing process such as MRF. This work explores ways to improve the surface finish of CVD ZnS processed with MRF through modification of the magnetorheological (MR) fluid's properties. A materials science approach is presented to define the anisotropy of CVD ZnS through a combination of chemical and mechanical experiments and theoretical predictions. Magnetorheological finishing experiments with single crystal samples of ZnS, whose cuts and orientations represent most of the facets known to occur in the polycrystalline CVD ZnS, were performed to explore the influence of material anisotropy on the material removal rate during MRF. By adjusting the fluid's viscosity, abrasive type concentration, and pH to find the chemo-mechanical conditions that equalize removal rates among all single crystal facets during MRF, we established an optimized, novel MR formulation to polish CVD ZnS without degrading the surface finish of the optic.

Why Do Photo Finish Images Look Weird?

ERIC Educational Resources Information Center

Gregorcic, Bor; Planinsic, Gorazd

2012-01-01

This paper deals with effects that appear on photographs of rotating objects when taken by a photo finish camera, a rolling shutter camera or a computer scanner. These effects are very similar to Roget's palisade illusion. A simple quantitative analysis of the images is also provided. The effects are explored using a computer scanner in a way that…

National Apprenticeship and Training Standards for Painting and Decorating and Drywall Finishing.

ERIC Educational Resources Information Center

Manpower Administration (DOL), Washington, DC. Bureau of Apprenticeship and Training.

The booklet presents the ninth edition of the national apprenticeship and training standards developed by the painting and decorating and drywall industry in cooperation with the Department of Labor's Bureau of Apprenticeship and Training. Provisions of national apprenticeship and training standards for painting and decorating and drywall…

40 CFR 63.5395 - How do I measure the density of a finish?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true How do I measure the density of a... Initial Compliance Requirements § 63.5395 How do I measure the density of a finish? (a) To determine the density of a finish, the reference method is EPA Method 24 of appendix A of 40 CFR part 60. You may use...

40 CFR 63.5395 - How do I measure the density of a finish?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 12 2011-07-01 2009-07-01 true How do I measure the density of a... Initial Compliance Requirements § 63.5395 How do I measure the density of a finish? (a) To determine the density of a finish, the reference method is EPA Method 24 of appendix A of 40 CFR part 60. You may use...

The effects of stainless steel finish on Salmonella Typhimurium attachment, biofilm formation and sensitivity to chlorine.

PubMed

Schlisselberg, Dov B; Yaron, Sima

2013-08-01

Bacterial colonization and biofilm formation on stainless steel (SS) surfaces can be sources for cross contamination in food processing facilities, possessing a great threat to public health and food quality. Here the aim was to demonstrate the influence of surface finish of AISI 316 SS on colonization, biofilm formation and susceptibility of Salmonella Typhimurium to disinfection. Initial attachment of S. Typhimurium on surfaces of SS was four times lower, when surface was polished by Bright-Alum (BA) or Electropolishing (EP), as compared to Mechanical Sanded (MS) or the untreated surface (NT). The correlation between roughness and initial bacterial attachment couldn't account on its own to explain differences seen. Biofilms with similar thickness (15-18 μm) were developed on all surfaces 1-day post inoculation, whereas EP was the least covered surface (23%). Following 5-days, biofilm thickness was lowest on EP and MS (30 μm) and highest on NT (62 μm) surfaces. An analysis of surface composition suggested a link between surface chemistry and biofilm development, where the higher concentrations of metal ions in EP and MS surfaces correlated with limited biofilm formation. Interestingly, disinfection of biofilms with chlorine was up to 130 times more effective on the EP surface (0.005% surviving) than on the other surfaces. Overall these results suggest that surface finish should be considered carefully in a food processing plant. Copyright © 2013 Elsevier Ltd. All rights reserved.

Genotype x environment interactions for fatty acid profiles in Bos indicus and Bos taurus finished on pasture or grain.

PubMed

Bressan, M C; Rossato, L V; Rodrigues, E C; Alves, S P; Bessa, R J B; Ramos, E M; Gama, L T

2011-01-01

A study was conducted to characterize lipid profiles in the M. longissimus thoracis of commercial Brazilian beef and to assess how those profiles are influenced by finishing system, genetic group, and their interaction. Intramuscular fat (IMF) and fatty acid (FA) profiles were determined in 160 bulls of the Bos taurus (n = 75) and Bos indicus (n = 85) genetic groups, finished on pasture (n = 46) or with grain supplementation (n = 114) and slaughtered in a commercial abattoir. Finishing system had a major impact on the deposition of IMF, as well as on the concentration of SFA, PUFA, and their ratio, but genetic groups showed important differences in the ability to convert SFA into cis-9 MUFA and to convert 16:0 into 18:0. When compared with pasture-finished animals, those finished with grain had greater content of IMF and SFA (P < 0.01), similar amounts of MUFA (P > 0.05), and about one-half the amount of PUFA (P < 0.01). Except for MUFA, differences in FA profiles among finishing systems were mostly mediated through their effect on IMF, even though the relationship of IMF with groups of FA differed among finishing systems. Under grain finishing, B. taurus had less SFA and greater MUFA than B. indicus (P < 0.01), but no differences were observed in PUFA (P > 0.05). With pasture-finishing, no differences were observed among the 2 genetic groups in SFA and MUFA (P > 0.05), but PUFA were decreased in B. taurus (P < 0.01). When genetic groups were compared in grain-finishing, B. taurus had a decreased ability for elongation and B. indicus had a decreased aptitude for desaturation of FA. On the other hand, with pasture-finishing a greater deposition of intermediate FA from ruminal biohydrogenation was observed in B. indicus than in B. taurus. Overall, FA profiles were affected more by finishing system in B. indicus than in B. taurus.

Calibration and prediction of removal function in magnetorheological finishing.

PubMed

Dai, Yifan; Song, Ci; Peng, Xiaoqiang; Shi, Feng

2010-01-20

A calibrated and predictive model of the removal function has been established based on the analysis of a magnetorheological finishing (MRF) process. By introducing an efficiency coefficient of the removal function, the model can be used to calibrate the removal function in a MRF figuring process and to accurately predict the removal function of a workpiece to be polished whose material is different from the spot part. Its correctness and feasibility have been validated by simulations. Furthermore, applying this model to the MRF figuring experiments, the efficiency coefficient of the removal function can be identified accurately to make the MRF figuring process deterministic and controllable. Therefore, all the results indicate that the calibrated and predictive model of the removal function can improve the finishing determinacy and increase the model applicability in a MRF process.

30 CFR 18.33 - Finish of surface joints.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Finish of surface joints. 18.33 Section 18.33 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC MOTOR-DRIVEN MINE EQUIPMENT AND ACCESSORIES Construction and Design...

Study on mycoflora of poultry feed ingredients and finished feed in Iran.

PubMed

Ghaemmaghami, Seyed Soheil; Modirsaneii, Mehrdad; Khosravi, Ali Reza; Razzaghi-Abyaneh, Mehdi

2016-02-01

Unhygienic poultry feedstuffs can lead to nutrient losses and detrimental effect on poultry production and public health. In the present study, mycobiota and colony-forming units per gram in ingredients and finish poultry feed was evaluated with special reference to potentially mycotoxigenic fungi. Eighty five samples of corn, soybean meal and poultry finished feed were collected from nine poultry feed factories located in three provinces i.e. Tehran, Alborz and Qom in Iran from October 2014 to January 2015. Samples were cultured on Sabouraud dextrose agar (SDA), Aspergillus flavus and parasiticus agar (AFPA) and dichloran rosebengal chloramphenicol agar (DRBC) and incubated at 28 °C for 7-10 days. Purified fungal colonies were identified by a combination of macro- and microscopic morphological criteria. For determining the rate of fungal contamination, samples were cultured on SDA and colony forming units (CFUs) were calculated. A total of 384 fungal isolates belonging to 7 genera of filamentous fungi and yeasts were obtained from corn (124 isolates), soybean meal (92 isolates), and feed before (72 isolates), and after pelleting (96 isolates). The most prominent fungal isolate in corn, soybean meal and feed before pelleting (feed as mash form) was Fusarium but in feed after pelleting was Aspergillus. Among 5 Aspergillus species isolated, potentially aflatoxigenic A. flavus isolates was predominant in corn (46.6%), soybean meal (72.7%) and poultry finished feed (75%). CFUs results indicated that 9/22 corn samples (40.9%), none of 22 soybean meal samples, 19/41 finished feed (46.3%) were contaminated higher than the standard limit. Our results indicated that corn, soybean meal and finished feed of poultry feed mill are contaminated with various fungal genera by different levels sometimes higher that the standard limits. Contamination with potentially mycotoxigenic fungi especially Aspergillus species may be considered as a human public health hazard.

40 CFR 429.130 - Applicability; description of the finishing subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., fabrication, and by-product utilization timber processing operations not otherwise covered by specific... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS TIMBER PRODUCTS PROCESSING POINT SOURCE CATEGORY Finishing...

A new seamless, smooth, interior, absorptive finishing system

NASA Astrophysics Data System (ADS)

D'Antonio, Peter

2003-10-01

Government architecture typically employs classic forms of vaults, domes and other focusing or reflective shapes, usually created with hard materials like concrete and plaster. The use of conventional porous absorption is typically rejected as an acoustical surface material for aesthetic reasons. Hence, many of these new and existing facilities have compromised speech intelligibility and music quality. Acousticians have sought a field-applied, absorptive finishing system that resembles a smooth plaster or painted drywall surface, since the dawn of architectural acoustics. Some success has been achieved using sprayed cellulose or cementitious materials, but surface smoothness has been a challenge. A new approach utilizing a thin microporous layer of mineral particles applied over a mineral wool panel will be described. This material can be applied to almost any shape surface, internally pigmented to match almost any color and renovated. Because of these unique characteristics the new seamless, absorptive, finishing system is being specified for many new and renovated spaces. Application examples will be presented.

40 CFR 427.80 - Applicability; description of the coating or finishing of asbestos textiles subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... coating or finishing of asbestos textiles subcategory. 427.80 Section 427.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ASBESTOS MANUFACTURING POINT SOURCE CATEGORY Coating or Finishing of Asbestos Textiles Subcategory § 427.80 Applicability...

40 CFR 427.80 - Applicability; description of the coating or finishing of asbestos textiles subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... coating or finishing of asbestos textiles subcategory. 427.80 Section 427.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ASBESTOS MANUFACTURING POINT SOURCE CATEGORY Coating or Finishing of Asbestos Textiles Subcategory § 427.80 Applicability; description...

40 CFR 427.80 - Applicability; description of the coating or finishing of asbestos textiles subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... coating or finishing of asbestos textiles subcategory. 427.80 Section 427.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ASBESTOS MANUFACTURING POINT SOURCE CATEGORY Coating or Finishing of Asbestos Textiles Subcategory § 427.80 Applicability...

40 CFR 427.80 - Applicability; description of the coating or finishing of asbestos textiles subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... coating or finishing of asbestos textiles subcategory. 427.80 Section 427.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) ASBESTOS MANUFACTURING POINT SOURCE CATEGORY Coating or Finishing of Asbestos Textiles Subcategory § 427.80 Applicability...

40 CFR 427.80 - Applicability; description of the coating or finishing of asbestos textiles subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... coating or finishing of asbestos textiles subcategory. 427.80 Section 427.80 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ASBESTOS MANUFACTURING POINT SOURCE CATEGORY Coating or Finishing of Asbestos Textiles Subcategory § 427.80 Applicability; description...

"Miss! I'm Done!" Finishing Craft Assignments as a Situated Activity System in Preschool

ERIC Educational Resources Information Center

Deunk, Marjolein; Berenst, Jan; de Glopper, Kees

2010-01-01

We describe the Situated Activity System of finishing craft assignments in preschool: the specific, routinized way that child and teacher jointly close the child's craft assignment, employing a specific discourse pattern. We analyzed the interactions of 14 Dutch children between 2.1 and 3.10 years old while they were finishing their craft…

Development of USTES Aptitude Test Battery for Photograph Finisher (Any Industry) I 976.886.

ERIC Educational Resources Information Center

Wisconsin State Employment Service, Madison.

To develop General Aptitude Test Battery (GATB) norms for the occupation of photograph finisher, 59 female workers employed as photograph finishers in Wisconsin were administered all 12 tests of the GATB and the Research Questionnaire-Background during July 1969. Supervisory ratings of job proficiency were made at approximately the same time as…

Heavy metal resistant endophytic fungi isolated from Nypa fruticans in Kuching Wetland National Park

NASA Astrophysics Data System (ADS)

Choo, Jenny; Sabri, Nuraini Binti Mohd; Tan, Daniel; Mujahid, Aazani; Müller, Moritz

2015-06-01

Heavy metal pollution is an environmental issue globally and the aim of this study was to isolate endophytic fungi from mangrove wetlands of Sarawak to assess and test their ability to grow in the presence of various heavy metals (copper (Cu), zinc (Zn), lead (Pb), and chromium (Cr)). Samples of Nypa fruticans were collected from Kuching Wetland National Park (KWNP) for subsequent endophyte isolation. Ninety-three (93) isolates were obtained and assessed and the most resistant isolates (growing at concentrations up to 1000 ppm) were identified using fungal primers ITS 1 and ITS 4. All of the endophytic fungi were identified to be closely related to Pestalotiopsis sp. and this is to our knowledge the first study reporting the ability of Pestalotiopsis sp. to grow at high concentrations of copper, lead, zinc and chromium. Our results highlight the potential of using endophytic fungi for the treatment of heavy metal pollution, for example as biosorbents.

Course in Carpentry: Interior Finish. Workbook and Tests.

ERIC Educational Resources Information Center

Strazicich, Mirko, Ed.

Designed for use in carpentry apprenticeship classes, this workbook contains nine units on carpentry skills in the area of interior finish, lists of recommended and required instructional materials, and nine unit tests. Each instructional unit includes a listing of performance statements and text covering skills addressed in individual performance…

Illinois Occupational Skill Standards: Finishing and Distribution Cluster.

ERIC Educational Resources Information Center

Illinois Occupational Skill Standards and Credentialing Council, Carbondale.

This document, which is intended as a guide for work force preparation program providers, details the Illinois occupational skill standards for programs preparing students for employment in occupations in the finishing and distribution cluster. The document begins with a brief overview of the Illinois perspective on occupational skill standards…

11. Exterior detail view of northeast corner, showing stucco finish ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. Exterior detail view of northeast corner, showing stucco finish and woodwork details - American Railway Express Company Freight Building, 1060 Northeast Division Street, Bend, Deschutes County, OR

Dust control technology usage patterns in the drywall finishing industry.

PubMed

Young-Corbett, Deborah E; Nussbaum, Maury A

2009-06-01

A telephone survey was conducted to quantify drywall finishing industry usage rates of dust control technology, identify barriers to technology adoption, and explore firm owner perception of risk. Industry use of the following technologies was described: wet methods, respiratory protection, pole sanders, ventilated sanders, and low-dust joint compound. A survey instrument composed of both Likert-type scaled items and open-ended items was developed and administered by telephone to the census population of the owners of member firms of trade associations: Finishing Contractors Association and Association of the Wall and Ceiling Industries. Of 857 firms, 264 interviews were completed. Along with descriptive statistics, results were analyzed to examine effects of firm size and union affiliation on responses. Responses to open-ended items were analyzed using content analysis procedures. Firm owners rated the risk of dust to productivity and customer satisfaction as low-moderate. Half rated the dust as having some impact on worker health, with higher impacts indicated by owners of small firms. Among the available control technologies, respiratory protection was used most frequently. Several barriers to implementation of the more effective control technologies were identified. Barriers associated with technology usability, productivity, and cost, as well as misperceptions of risk, should be addressed to improve dust control in the drywall finishing industry.

Effect of different surface finishing/polishing procedures on color stability of esthetic restorative materials: A spectrophotometric evaluation

PubMed Central

Beltrami, Riccardo; Ceci, Matteo; De Pani, Gabriele; Vialba, Lodovico; Federico, Ricaldone; Poggio, Claudio; Colombo, Marco

2018-01-01

Objective: To evaluate the color stability of different esthetic restorative materials after surface finishing/polishing with different procedures. Materials and Methods: All materials were polymerized into silicone rubber rings to obtain specimens identical in size. Samples were randomly assigned into four groups (10 specimens of each composite for each group), and they were finished with different procedures: Control group (Group 1), three or two polishers interspersed with diamond grit (Groups 3 and 2, respectively), and one tungsten carbide bur + one polisher interspersed with diamond grit (Group 4). After staining process in coffee, a colorimetric evaluation according to the CIE L*a*b* system was performed by a blind trained operator at 7, 14, 21, and 28 days. Shapiro–Wilk test and Kruskal–Wallis analysis of variance were applied to assess significant differences among restorative materials. Means of the different polishing/finishing groups were compared with Scheffe's multiple comparison test at the 0.05 level of significance. Results: In control group, significant lower discolorations were recorded for Essentia, Admira Fusion, and Estelite. After finishing, Filtek Supreme XTE and Ceram.X Universal showed a significantly lower degree of staining. The finishing technique used for Group 4 produced higher color changes. Conclusions: Tungsten carbide burs produced the higher color variations; after finishing, the nanofilled composites showed lower discoloration than nanohybrid ones, and the time of exposure to the staining agent and the polishing/finishing technique influenced the color change. PMID:29657525

An instrument for the geometric attributes of metallic appearance.

PubMed

Christie, J S

1969-09-01

With the use of a greater variety of metals and methods of finishing them, an increasing need to measure metallic appearance has developed in the automotive industry. A simple and easy to operate instrument has been designed to measure the geometric characteristics of reflectance related to metallic appearance. These are specular reflectance, distinctness of image, haze, and diffuseness. A series of selected aluminum and stainless steel specimens has been used to test the performance of the new instrument and of older devices with which it has been compared. Functionally, the new instrument combines features of the Distinctness of ReflectedImage (DORI)meter designed by Tingle, and the abridged goniophotometer designed by Tingle and George. The design and operation of the new instrument have been simplified by use of multiple receptor apertures with optical fiber light collectors. The measurement of a wide range of metal appearance characteristic has thus been achieved with mechanical and electrical circuit simplicity.

77 FR 61025 - Certain Prepregs, Laminates, and Finished Circuit Boards: Notice of Institution of Formal...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-05

... INTERNATIONAL TRADE COMMISSION [Inv. No. 337-TA-659] Certain Prepregs, Laminates, and Finished..., and the sale within the United States after importation of certain prepregs, laminates, and finished... for sale, and selling for importation into the United States prepregs and laminates that are the...

Liquid-metal plasma-facing component research on the National Spherical Torus Experiment

NASA Astrophysics Data System (ADS)

Jaworski, M. A.; Khodak, A.; Kaita, R.

2013-12-01

Liquid metal plasma-facing components (PFCs) have been proposed as a means of solving several problems facing the creation of economically viable fusion power reactors. Liquid metals face critical issues in three key areas: free-surface stability, material migration and demonstration of integrated scenarios. To date, few demonstrations exist of this approach in a diverted tokamak and we here provide an overview of such work on the National Spherical Torus Experiment (NSTX). The liquid lithium divertor (LLD) was installed and operated for the 2010 run campaign using evaporated coatings as the filling method. Despite a nominal liquid level exceeding the capillary structure and peak current densities into the PFCs exceeding 100 kA m-2, no macroscopic ejection events were observed. The stability can be understood from a Rayleigh-Taylor instability analysis. Capillary restraint and thermal-hydraulic considerations lead to a proposed liquid-metal PFCs scheme of actively-supplied, capillary-restrained systems. Even with state-of-the-art cooling techniques, design studies indicate that the surface temperature with divertor-relevant heat fluxes will still reach temperatures above 700 °C. At this point, one would expect significant vapor production from a liquid leading to a continuously vapor-shielded regime. Such high-temperature liquid lithium PFCs may be possible on the basis of momentum-balance arguments.

Influence of substrate material and surface finishing on the morphology of the calcium-phosphate coating.

PubMed

Leitão, E; Barbosa, M A; de Groot, K

1997-07-01

The formation of an apatite-like layer was achieved by immersing Ti-6A1-4V, Ti-Al-2.5Fe, and 316 L stainless-steel substrata in Hank's balanced salt solution (HBSS). The layer was characterized by surface analysis techniques, namely X-ray microanalysis and X-ray diffraction, and the morphology was observed by scanning electron microscopy and atomic force microscopy. The concentrations of Ca and P were monitored as a function of time. The morphology of the precipitate layer seems to be dependent both on the type of metal substrate and its surface finish. Polished Ti-6A1-4V and Ti-Al-2.5Fe surfaces exhibit a plate precipitate morphology, whereas rougher surfaces show scattered crystal-like precipitation. The results suggest that the layer produced by immersion of polished titanium alloys in HBSS is constituted by an amorphous apatite.

Surface topographical effects on the structural growth of thick sputtered metal and alloy coatings

NASA Technical Reports Server (NTRS)

Spalvins, T.; Brainard, W. A.

1974-01-01

Thick sputtered S-Monel, silver, and 304 stainless steel coatings were deposited on mica and metal substrates with various surface finishes to investigate the structural growth of the coating by scanning electron microscopy. The geometry and the surface structure of the nodules are characterized. Compositional changes within the coating were analyzed by X-ray dispersion miscroscopy. Defects in the surface finish act as preferential nucleation sites and form isolated and complex nodules and various surface overgrowths in the coating. The nodule boundaries are very vulnerable to chemical etching, and these nodules do not disappear after full annealing. Further, they have undesirable effects on mechanical properties; cracks are initiated at the nodules when the coating is stressed by mechanical forces.

Performance evaluation of a dental handpiece in simulation of clinical finishing using a novel 2DOF in vitro apparatus.

PubMed

Yin, L; Song, X F; Qu, S F; Huang, T; Mei, J P; Yang, Z Y; Li, J

2006-11-01

This paper reports on the performance evaluation of a dental handpiece in simulation of clinical finishing using a novel two-degrees-of-freedom (2DOF) in vitro apparatus. The instrumented apparatus consisted of a two-dimensional computer-controlled coordinate worktable carrying a dental handpiece, a piezoelectric force dynamometer, and a high-speed data acquisition and signal conditioning system for simulating the clinical operations and monitoring the dental finishing processes. The performance of the dental handpiece was experimentally evaluated with respect to rotational speed, torque, and specific finishing energy under the applied clinical finishing conditions. The results show that the rotational speeds of the dental handpiece decreased by increasing either the depth of cut or the feed rate at a constant clinically applied air pressure and water flowrate. They also decreased when increasing both the tangential and normal finishing forces. The specific finishing energy decreased with an increase in either depth of cut or feed rate, while the finishing torque increased as either the depth of cut or the feed rate was increased. Implications of these results were to provide guidance for proper applications of dental handpieces in clinical practice.

40 CFR 141.510 - Is my system subject to the new finished water reservoir requirements?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 24 2013-07-01 2013-07-01 false Is my system subject to the new finished water reservoir requirements? 141.510 Section 141.510 Protection of Environment ENVIRONMENTAL... Filtration and Disinfection-Systems Serving Fewer Than 10,000 People Finished Water Reservoirs § 141.510 Is...

40 CFR 141.510 - Is my system subject to the new finished water reservoir requirements?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 24 2012-07-01 2012-07-01 false Is my system subject to the new finished water reservoir requirements? 141.510 Section 141.510 Protection of Environment ENVIRONMENTAL... Filtration and Disinfection-Systems Serving Fewer Than 10,000 People Finished Water Reservoirs § 141.510 Is...

Fatty acid metabolism and deposition in subcutaneous adipose tissue of pasture and feedlot finished cattle

USDA-ARS?s Scientific Manuscript database

An experiment was conducted to evaluate the effects of pasture finishing versus high-concentrate finishing, over time, on fatty acid metabolism in Angus crossbred (n = 24) steers. Ruminal fluid, serum, and adipose tissue biopsies were obtained on d 0, 28, 84, and 140. Pasture forages and diet ingr...

Finishing/polishing of composite and compomer restoratives: effectiveness of one-step systems.

PubMed

Yap, Adrian U J; Yap, S H; Teo, C K; Ng, J J

2004-01-01

This study investigated the surface texture of composite (Z100, 3M ESPE) and compomer (F2000, 3M ESPE) restoratives after treatment with different one-step finishing/polishing systems (One-Gloss [OG], Shofu; PoGo [PG], Dentsply; Sof-Lex Brush [SB], 3M ESPE). The surface roughness obtained was compared to that using a matrix strip [MS], a two-step rubber abrasive (CompoSite [CS], Shofu) and a graded abrasive disk (Super Snap [SS], Shofu) system. Eight specimens (3-mm long x 3-mm wide x 2-mm deep) of each material were made according to manufacturer's instructions. With exception of the MS group, all groups were roughened with 320 grit grinding paper using a lapping device prior to finishing/polishing with the different systems. The mean surface roughness (microm) was measured with a profilometer. Data was subjected to ANOVA/Scheffe's tests and independent samples t-test at significance level 0.05. Mean Ra ranged from 0.22 to 0.32 microm for Z100 and 0.45 to 0.68 for F2000. For both materials, the smoothest surfaces were obtained with MS. The roughest surfaces were observed after treatment with SS and OG for Z100 and F2000, respectively. The effectiveness of the finishing/polishing systems was material dependent. The surface finish produced by PG and SB was superior or comparable to that obtained with CS, SS and OG.

UltraForm Finishing (UFF) a 5-axis computer controlled precision optical component grinding and polishing system

NASA Astrophysics Data System (ADS)

Bechtold, Michael; Mohring, David; Fess, Edward

2007-05-01

OptiPro Systems has developed a new finishing process for the manufacturing of precision optical components. UltraForm Finishing (UFF) has evolved from a tire shaped tool with polishing material on its periphery, to its newest design, which incorporates a precision rubber wheel wrapped with a band of polishing material passing over it. Through our research we have developed a user friendly graphical interface giving the optician a deterministic path for finishing precision optical components. Complex UFF Algorithms combine the removal function and desired depth of removal into a motion controlled tool path which minimizes surface roughness and form errors. The UFF process includes 5 axes of computer controlled motion, (3 linear and 2 rotary) which provide the flexibility for finishing a variety of shapes including spheres, aspheres, and freeform optics. The long arm extension, along with a range of diameters for the "UltraWheel" provides a unique solution for the finishing of steep concave shapes such as ogives and domes. The UltraForm process utilizes, fixed and loose abrasives, in combination with our proprietary "UltraBelts" made of a range of materials such as polyurethane, felt, resin, diamond and others.

Influence of Finishing and Polishing Techniques and Abrasion on Transmittance and Roughness of Composite Resins.

PubMed

Carneiro, Pma; Ramos, T M; de Azevedo, C S; de Lima, E; de Souza, Shj; Turbino, M L; Cesar, P F; Matos, A B

The aim of this study was to evaluate the influence of finishing and polishing systems and toothbrush abrasion on transmittance (T) and surface roughness (Ra) of three composite resins (Filtek Z350 XT, Tetric N-Ceram, and IPS Empress Direct). Eighteen resin disks (10 mm diameter × 2 mm thick) finished by polyester strips had initial surface smoothness recorded, representing phase 1 (P1). Specimens were divided into three groups (n=6) according to the finishing/polishing instrument used (OneGloss, TopGloss, and Sof-Lex) to compose phase 2 samples (P2). Then specimens were subjected to 514 cycles of toothbrush simulation using a toothpaste slurry, with a constant load applied to soft bristles, and were then washed (phase 3=P3). After each phase, the specimens were examined by an optical profiler and spectrophotometer to measure Ra and T. Data were analyzed by analysis of variance, Tukey and Pearson tests. T values were statistically influenced by composite resin ( p=0.000) and phase of measurement ( p=0.000) factors, while the finishing/polishing system used ( p=0.741) did not affect T. On the other hand, Ra values were statistically affected by the factor finishing/polishing system ( p=0.000), but not by composite resin ( p=0.100) and phase of measurement ( p=0.451). Tetric N-Ceram and Empress Direct presented higher values of roughness when polished by OneGloss, while TopGloss and Sof-Lex showed a lower roughness. It can be concluded that composite resins transmitted more light after dental abrasion. Transmittance of composite resins was not modified by the distinct roughness created by finishing/polishing instruments.

DETECTION OF CRYPTOSPORIDIUM OOCYSTS IN SOURCE AND FINISHED WATERS

EPA Science Inventory

Numerous waterborne outbreaks of cryptosporidiosis have occurred with the most notable being the 1993 episode in Milwaukee. As a result, the past decade has seen a massive effort expended on the development of methods to detect Cryptosporidium parvum oocysts in source and finish...

40 CFR 425.30 - Applicability; description of the hair save or pulp, non-chrome tan, retan-wet finish subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Applicability; description of the hair... TANNING AND FINISHING POINT SOURCE CATEGORY Hair Save or Pulp, Non-Chrome Tan, Retan-Wet Finish Subcategory § 425.30 Applicability; description of the hair save or pulp, non-chrome tan, retan-wet finish...

40 CFR 425.30 - Applicability; description of the hair save or pulp, non-chrome tan, retan-wet finish subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 30 2014-07-01 2014-07-01 false Applicability; description of the hair... TANNING AND FINISHING POINT SOURCE CATEGORY Hair Save or Pulp, Non-Chrome Tan, Retan-Wet Finish Subcategory § 425.30 Applicability; description of the hair save or pulp, non-chrome tan, retan-wet finish...

40 CFR 425.30 - Applicability; description of the hair save or pulp, non-chrome tan, retan-wet finish subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Applicability; description of the hair... FINISHING POINT SOURCE CATEGORY Hair Save or Pulp, Non-Chrome Tan, Retan-Wet Finish Subcategory § 425.30 Applicability; description of the hair save or pulp, non-chrome tan, retan-wet finish subcategory. The...

40 CFR 425.30 - Applicability; description of the hair save or pulp, non-chrome tan, retan-wet finish subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false Applicability; description of the hair... TANNING AND FINISHING POINT SOURCE CATEGORY Hair Save or Pulp, Non-Chrome Tan, Retan-Wet Finish Subcategory § 425.30 Applicability; description of the hair save or pulp, non-chrome tan, retan-wet finish...

Sensory quality of beef from different finishing diets.

PubMed

Resconi, V C; Campo, M M; Font i Furnols, M; Montossi, F; Sañudo, C

2010-11-01

Beef production under different local husbandry systems might have meat sensory quality implications for the marketing of these products abroad. In order to assess the effect of finishing diet systems on beef quality, a trained sensory taste panel assessed meat aged for 20 days from 80 Uruguayan Hereford steers that were finished on one of the following diets: T1=Pasture [4% of animal live weight (LW)], T2=Pasture [3% LW plus concentrate (0.6% LW)], T3=Pasture [3% LW plus concentrate (1.2% LW)], or T4=Concentrate plus hay ad libitum. Beef odour and flavour intensities decreased with an increase in the energy content of the diet. The meat from T2 had the lowest acid flavour and strange odours intensities. In general, steers fed only concentrate plus hay (T4) produced meat that had an inferior sensory quality because they had more pronounced off-flavours and was tougher. Copyright © 2010 The American Meat Science Association. Published by Elsevier Ltd. All rights reserved.

Finish line distinctness and accuracy in 7 intraoral scanners versus conventional impression: an in vitro descriptive comparison.

PubMed

Nedelcu, Robert; Olsson, Pontus; Nyström, Ingela; Thor, Andreas

2018-02-23

Several studies have evaluated accuracy of intraoral scanners (IOS), but data is lacking regarding variations between IOS systems in the depiction of the critical finish line and the finish line accuracy. The aim of this study was to analyze the level of finish line distinctness (FLD), and finish line accuracy (FLA), in 7 intraoral scanners (IOS) and one conventional impression (IMPR). Furthermore, to assess parameters of resolution, tessellation, topography, and color. A dental model with a crown preparation including supra and subgingival finish line was reference-scanned with an industrial scanner (ATOS), and scanned with seven IOS: 3M, CS3500 and CS3600, DWIO, Omnicam, Planscan and Trios. An IMPR was taken and poured, and the model was scanned with a laboratory scanner. The ATOS scan was cropped at finish line and best-fit aligned for 3D Compare Analysis (Geomagic). Accuracy was visualized, and descriptive analysis was performed. All IOS, except Planscan, had comparable overall accuracy, however, FLD and FLA varied substantially. Trios presented the highest FLD, and with CS3600, the highest FLA. 3M, and DWIO had low overall FLD and low FLA in subgingival areas, whilst Planscan had overall low FLD and FLA, as well as lower general accuracy. IMPR presented high FLD, except in subgingival areas, and high FLA. Trios had the highest resolution by factor 1.6 to 3.1 among IOS, followed by IMPR, DWIO, Omnicam, CS3500, 3M, CS3600 and Planscan. Tessellation was found to be non-uniform except in 3M and DWIO. Topographic variation was found for 3M and Trios, with deviations below +/- 25 μm for Trios. Inclusion of color enhanced the identification of the finish line in Trios, Omnicam and CS3600, but not in Planscan. There were sizeable variations between IOS with both higher and lower FLD and FLA than IMPR. High FLD was more related to high localized finish line resolution and non-uniform tessellation, than to high overall resolution. Topography variations were low

The effect of veneering on the marginal fit of CAD/CAM-generated, copy-milled, and cast metal copings.

PubMed

Ates, Sabit Melih; Yesil Duymus, Zeynep; Caglar, Ipek; Hologlu, Bilal

2017-11-01

This in vitro study investigated the marginal fit of metal and zirconia copings before and after veneering on dies with shoulder/chamfer (s/c) finish lines. Using CAD/CAM, ten (n = 10) each s/c zirconia (NZ) copings and ten (n = 10) each s/c metal (MM) copings were generated. As controls, ten (n = 10) each s/c zirconia copings were copy-milled (ZZ) and ten (n = 10) each s/c metal copings were cast (CC). The vertical marginal discrepancy of the copings was measured at 20 predefined spots of the circular shoulder and chamfer finish lines in microns (μm) before and after a first and a second veneering firing using a stereomicroscope at ×40 magnification. Data were statistically analyzed, and the comparisons of CAD/CAM-milled (NZ, MM), copy-milled (ZZ), and cast (CC) copings before and after veneering were made at a significance level of p < 0.05. Gap width at s/c finish lines of ZZ was (91 ± 11/100 ± 28) and increased significantly (109 ± 21/141 ± 18) after the first firing (ZZ1). NZ showed significantly smaller gaps than ZZ (36 ± 6/46 ± 12) and (NZ1) after the first firing (61 ± 16/71 ± 29). Gap widths of CC groups (36 ± 8/25 ± 4) were not significantly different from NZ but were significantly lower after the (CC1) first veneering firing (40 ± 8/42 ± 7). MM copings showed gap values similar to NZ. Second firings did not significantly increase gaps in all groups except ZZ2 of chamfer finish line. Veneering increased the marginal gap width of copings. Within the limits of this in vitro study, aesthetic ceramic veneering of CAD/CAM-generated copings caused a statistically significant but tolerable loss of marginal fit precision.

Study on mycoflora of poultry feed ingredients and finished feed in Iran

PubMed Central

Ghaemmaghami, Seyed Soheil; Modirsaneii, Mehrdad; Khosravi, Ali Reza; Razzaghi-Abyaneh, Mehdi

2016-01-01

Background and Objectives: Unhygienic poultry feedstuffs can lead to nutrient losses and detrimental effect on poultry production and public health. In the present study, mycobiota and colony-forming units per gram in ingredients and finish poultry feed was evaluated with special reference to potentially mycotoxigenic fungi. Materials and Methods: Eighty five samples of corn, soybean meal and poultry finished feed were collected from nine poultry feed factories located in three provinces i.e. Tehran, Alborz and Qom in Iran from October 2014 to January 2015. Samples were cultured on Sabouraud dextrose agar (SDA), Aspergillus flavus and parasiticus agar (AFPA) and dichloran rosebengal chloramphenicol agar (DRBC) and incubated at 28 °C for 7–10 days. Purified fungal colonies were identified by a combination of macro- and microscopic morphological criteria. For determining the rate of fungal contamination, samples were cultured on SDA and colony forming units (CFUs) were calculated. Results: A total of 384 fungal isolates belonging to 7 genera of filamentous fungi and yeasts were obtained from corn (124 isolates), soybean meal (92 isolates), and feed before (72 isolates), and after pelleting (96 isolates). The most prominent fungal isolate in corn, soybean meal and feed before pelleting (feed as mash form) was Fusarium but in feed after pelleting was Aspergillus. Among 5 Aspergillus species isolated, potentially aflatoxigenic A. flavus isolates was predominant in corn (46.6%), soybean meal (72.7%) and poultry finished feed (75%). CFUs results indicated that 9/22 corn samples (40.9%), none of 22 soybean meal samples, 19/41 finished feed (46.3%) were contaminated higher than the standard limit. Conclusions: Our results indicated that corn, soybean meal and finished feed of poultry feed mill are contaminated with various fungal genera by different levels sometimes higher that the standard limits. Contamination with potentially mycotoxigenic fungi especially Aspergillus

Concentration data for anthropogenic organic compounds in groundwater, surface water, and finished water of selected community water systems in the United States, 2002-10

USGS Publications Warehouse

Carter, Janet M.; Kingsbury, James A.; Hopple, Jessica A.; Delzer, Gregory C.

2010-01-01

The National Water-Quality Assessment Program of the U.S. Geological Survey began implementing Source Water-Quality Assessments (SWQAs) in 2001 that focus on characterizing the quality of source water and finished water of aquifers and major rivers used by some of the larger community water systems in the United States. As used in SWQA studies, source water is the raw (ambient) water collected at the supply well before water treatment (for groundwater) or the raw (ambient) water collected from the river near the intake (for surface water), and finished water is the water that has been treated and is ready to be delivered to consumers. Finished-water samples are collected before the water enters the distribution system. The primary objective of SWQAs is to determine the occurrence of more than 250 anthropogenic organic compounds in source water used by community water systems, many of which currently are unregulated in drinking water by the U.S. Environmental Protection Agency. A secondary objective is to understand recurrence patterns in source water and determine if these patterns also occur in finished water before distribution. SWQA studies were conducted in two phases for most studies completed by 2005, and in one phase for most studies completed since 2005. Analytical results are reported for a total of 295 different anthropogenic organic compounds monitored in source-water and finished-water samples collected during 2002-10. The 295 compounds were classified according to the following 13 primary use or source groups: (1) disinfection by-products; (2) fumigant-related compounds; (3) fungicides; (4) gasoline hydrocarbons, oxygenates, and oxygenate degradates; (5) herbicides and herbicide degradates; (6) insecticides and insecticide degradates; (7) manufacturing additives; (8) organic synthesis compounds; (9) pavement- and combustion-derived compounds; (10) personal-care and domestic-use products; (11) plant- or animal-derived biochemicals; (12) refrigerants and

Wean-to-finish feeder space availability effects on nursery and finishing pig performance and total tract digestibility in a commercial setting when feeding dried distillers grains with solubles.

PubMed

Weber, E K; Stalder, K J; Patience, J F

2015-04-01

The study objectives were to determine nursery phase feeder space allowance effects on pig performance when double stocked and, second, to determine feeder space allowance and dried distillers grains with solubles (DDGS) inclusion level effects on pig performance and nutrient digestibility during the growing-finishing phase. This study was performed on the same group of pigs within a commercial wean-finish system. For the nursery phase, a completely randomized design was used to compare 3 feeder space allowance treatments (2.1, 2.5, and 2.9 cm/pig). A total of 3,720 pigs were randomly allotted to same-sex pens (10 feeders/treatment) housing 62 pigs/pen. Thirty 7-hole, double-sided feeders were utilized in the study. Differing linear feeder space treatments were established by blocking off sections for the nursery and grow-finish portions of this experiment. All pigs were provided equal floor space (0.26 m2/pig). In the grow-finish phase, a total of 1,860 pigs (n = 60 pens) were utilized in a 2 × 3 factorial design with 3 feeder space allowances (4.1, 4.9, or 5.7 cm/pig) and 2 dietary DDGS treatments (30% [D30] or 60% [D60]). Fecal and diet samples were collected and analyzed to estimate apparent total tract digestibility percentage (ATTD %). In the nursery portion of the trial, there was no feeder space treatment effect on ADG, ADFI, or feed efficiency (P > 0.10) from weaning to d 56 postweaning or during any weigh period. In the grow-finish portion of the trial, feeder space allowance and DDGS inclusion level did not affect ADG, ADFI, or feed efficiency (P > 0.05) from d 57 postweaning to market. Pigs fed the D30 diet had greater HCW, percent yield, and loin depth than those on the D60 diet (P < 0.05). Pigs fed the D30 treatment had greater (P < 0.05) ATTD for DM and GE for both collection periods compared with those on the D60 treatment. In summary, feeder space allowance did not impact pig performance during the nursery or grow-finish production phases

Experimental analysis on semi-finishing machining of Ti6Al4V additively manufactured by direct melting laser sintering

NASA Astrophysics Data System (ADS)

Imbrogno, Stano; Bordin, Alberto; Bruschi, Stefania; Umbrello, Domenico

2016-10-01

The Additive Manufacturing (AM) techniques are particularly appealing especially for titanium aerospace and biomedical components because they permit to achieve a strong reduction of the buy-to-fly ratio. However, finishing machining operations are often necessary to reduce the uneven surface roughness and geometrics because of local missing accuracy. This work shows the influence of the cutting parameters, cutting speed and feed rate, on the cutting forces as well as on the thermal field observed in the cutting zone, during a turning operation carried out on bars made of Ti6Al4V obtained by the AM process called Direct Metal Laser Sintering (DMLS). Moreover, the sub-surface microstructure alterations due to the process are also showed and commented.

Finishing bacterial genome assemblies with Mix.

PubMed

Soueidan, Hayssam; Maurier, Florence; Groppi, Alexis; Sirand-Pugnet, Pascal; Tardy, Florence; Citti, Christine; Dupuy, Virginie; Nikolski, Macha

2013-01-01

Among challenges that hamper reaping the benefits of genome assembly are both unfinished assemblies and the ensuing experimental costs. First, numerous software solutions for genome de novo assembly are available, each having its advantages and drawbacks, without clear guidelines as to how to choose among them. Second, these solutions produce draft assemblies that often require a resource intensive finishing phase. In this paper we address these two aspects by developing Mix , a tool that mixes two or more draft assemblies, without relying on a reference genome and having the goal to reduce contig fragmentation and thus speed-up genome finishing. The proposed algorithm builds an extension graph where vertices represent extremities of contigs and edges represent existing alignments between these extremities. These alignment edges are used for contig extension. The resulting output assembly corresponds to a set of paths in the extension graph that maximizes the cumulative contig length. We evaluate the performance of Mix on bacterial NGS data from the GAGE-B study and apply it to newly sequenced Mycoplasma genomes. Resulting final assemblies demonstrate a significant improvement in the overall assembly quality. In particular, Mix is consistent by providing better overall quality results even when the choice is guided solely by standard assembly statistics, as is the case for de novo projects. Mix is implemented in Python and is available at https://github.com/cbib/MIX, novel data for our Mycoplasma study is available at http://services.cbib.u-bordeaux2.fr/mix/.

Machine finishes balls to high degree of roundness

NASA Technical Reports Server (NTRS)

Angele, W.; Hill, J. P., Jr.

1972-01-01

Machine was developed to finish ball to roundness within 12.5 nm (half a microinch) from any types of hard material. Grinding and polishing to this tolerance is accomplished by lapping elements on four to six motor-driven spindles. Spindles are adjustably spring-loaded to ensure constant contact pressure on ball and are driven by variable speed electric motors.

Study on effect of tool electrodes on surface finish during electrical discharge machining of Nitinol

NASA Astrophysics Data System (ADS)

Sahu, Anshuman Kumar; Chatterjee, Suman; Nayak, Praveen Kumar; Sankar Mahapatra, Siba

2018-03-01

Electrical discharge machining (EDM) is a non-traditional machining process which is widely used in machining of difficult-to-machine materials. EDM process can produce complex and intrinsic shaped component made of difficult-to-machine materials, largely applied in aerospace, biomedical, die and mold making industries. To meet the required applications, the EDMed components need to possess high accuracy and excellent surface finish. In this work, EDM process is performed using Nitinol as work piece material and AlSiMg prepared by selective laser sintering (SLS) as tool electrode along with conventional copper and graphite electrodes. The SLS is a rapid prototyping (RP) method to produce complex metallic parts by additive manufacturing (AM) process. Experiments have been carried out varying different process parameters like open circuit voltage (V), discharge current (Ip), duty cycle (τ), pulse-on-time (Ton) and tool material. The surface roughness parameter like average roughness (Ra), maximum height of the profile (Rt) and average height of the profile (Rz) are measured using surface roughness measuring instrument (Talysurf). To reduce the number of experiments, design of experiment (DOE) approach like Taguchi’s L27 orthogonal array has been chosen. The surface properties of the EDM specimen are optimized by desirability function approach and the best parametric setting is reported for the EDM process. Type of tool happens to be the most significant parameter followed by interaction of tool type and duty cycle, duty cycle, discharge current and voltage. Better surface finish of EDMed specimen can be obtained with low value of voltage (V), discharge current (Ip), duty cycle (τ) and pulse on time (Ton) along with the use of AlSiMg RP electrode.

Concentrations of metals in aquatic invertebrates from the Ozark National Scenic Riverways, Missouri

USGS Publications Warehouse

Schmitt, Christopher J.; Brumbaugh, William G.; Besser, John M.; May, Thomas W.

2007-01-01

This report summarizes the findings of a study conducted as a pilot for part of a park-wide monitoring program being developed for the Ozark National Scenic Riverways (ONSR) of southeastern Missouri. The objective was to evaluate using crayfish (Orconectes spp.) and Asian clam (Corbicula fluminea) for monitoring concentrations of metals associated with lead-zinc mining. Lead-zinc mining presently (2007) occurs near the ONSR and additional mining has been proposed. Three composite samples of each type (crayfish and Asian clam), each comprising ten animals of approximately the same size, were collected during late summer and early fall of 2005 from five sites on the Current River and Jacks Fork within the ONSR and from one site on the Eleven Point River and the Big River, which are outside the ONSR. The Big River has been contaminated by mine tailings from historical leadzinc mining. Samples were analyzed by inductively coupled plasma mass spectrometry for lead, zinc, cadmium, cobalt, and nickel concentrations. All five metals were detected in all samples; concentrations were greatest in samples of both types from the Big River, and lowest in samples from sites within the ONSR. Concentrations of zinc and cadmium typically were greater in Asian clams than in crayfish, but differences were less evident for the other metals. In addition, differences among sites were small for cobalt in Asian clams and for zinc in crayfish, indicating that these metals are internally regulated to some extent. Consequently, both sample types are recommended for monitoring. Concentrations of metals in crayfish and Asian clams were consistent with those reported by other studies and programs that sampled streams in southeast Missouri.

218. CURVE ON FINISHED ROAD AT STATION 803+, WITH CAR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

218. CURVE ON FINISHED ROAD AT STATION 803+, WITH CAR AND CEDAR LAMP POST, 1930 - George Washington Memorial Parkway, Along Potomac River from McLean to Mount Vernon, VA, Mount Vernon, Fairfax County, VA

Antibacterial and anti-inflammatory finishing of cotton by microencapsulation using three marine organisms.

PubMed

El-Rafie, H M; El-Rafie, M H; AbdElsalam, H M; El-Sayed, W A

2016-05-01

This work is a small effort in the production of an eco-friendly natural based antibacterial and anti-inflammatory finished cotton fabrics using the ethanolic extracts (Ex) of the sea grass Halophila stipulacea (H. stipulacea) and marine macroalgae [Colbomenia sinuosa (C. sinuosa) and Ulva fasciata (U. fasciata)]. The extracts were phytochemically screened for their constituents. These extracts were used to finish cotton fabrics by a variety of methods. Concerning this, fabrics (F) were singly treated with ethanolic extracts (ExF) of these marine organisms by the dip technique and the extract encapsulated with sodium alginate or meypro gum. The encapsulated fabric (EnF) was further finished individually with citric acid (CA), (EnF/CA) and mono-tert-butyl ether of glycerol (MTBG) binder (EnF/Bin) by the pad-dry-cure technique. The fabrics so-finished were evaluated for their antibacterial and anti-inflammatory activities without washing (control) and after different washing cycles. The results obtained showed that, both EnF/CA and EnF/Bin inhibit the bacterial growth by about 90% after 10 washing cycles for both Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus). The anti-inflammatory activity, the potency% reached to 88.3% for the fabric encapsulated with microcapsules of sodium alginate/H. stipulacea sea grass and the EnF/CA. Copyright © 2016 Elsevier B.V. All rights reserved.

Effect of Various Finishing Procedures on the Reflectivity (Shine) of Tooth Enamel - An In-vitro Study.

PubMed

Patil, Harshal Ashok; Chitko, Shrikant Shrinivas; Kerudi, Veerendra Virupaxappa; Maheshwari, Amit Ratanlal; Patil, Neeraj Suresh; Tekale, Pawankumar Dnyandeo; Gore, Ketan Ashorao; Zope, Amit Ashok

2016-08-01

Reflectivity of an object is a good parameter for surface finish. As the patient evaluates finishing as a function of gloss/reflectivity/shine an attempt is made here to evaluate changes in surface finish with custom made reflectometer. The aim of the present study was to study the effect of various procedures during orthodontic treatment on the shine of enamel, using a custom made reflectometer. Sixty one extracted premolars were collected and each tooth was mounted on acrylic block. Reflectivity of the teeth was measured as compared to standard before any procedure. One tooth was kept as standard throughout the study. Sixty teeth were acid etched. Reflectivity was measured on custom made reflectometer and readings recorded. Same procedure was repeated after debonding. Then 60 samples were divided into three groups: Group 1 - Tungsten Carbide, Group 2 - Astropol, Group 3- Sof-Lex disc depending upon the finishing method after debonding and reflectivity was measured. The mean percentage of reflectivity after acid etching was 31.4%, debonding 45.5%, Tungsten carbide bur finishing (Group 1) was 58.3%, Astropol (Group 2) 72.8%, and Sof-Lex disc (Group 3) 84.4% as that to the standard. There was statistically very highly significant (p<0.001) difference in reflectivity restored by the three finishing materials in the study. Thus, the light reflection was better in Group 3> Group 2> Group 1. The primary goal was to restore the enamel to its original state after orthodontic treatment. The methods tested in this study could not restore the original enamel reflectivity.

Inaugural Technology Showcase Draws Hundreds | Frederick National Laboratory for Cancer Research

Cancer.gov

Before a crowded auditorium of science and business professionals at the Frederick National Laboratory for Cancer Research’s Advanced Technology Research Facility (ATRF), Joost Oppenheim, M.D., had just finished his presentation about a compound th

Machining the Integral Impeller and Blisk of Aero-Engines: A Review of Surface Finishing and Strengthening Technologies

NASA Astrophysics Data System (ADS)

Fu, Youzhi; Gao, Hang; Wang, Xuanping; Guo, Dongming

2017-05-01

The integral impeller and blisk of an aero-engine are high performance parts with complex structure and made of difficult-to-cut materials. The blade surfaces of the integral impeller and blisk are functional surfaces for power transmission, and their surface integrity has significant effects on the aerodynamic efficiency and service life of an aero-engine. Thus, it is indispensable to finish and strengthen the blades before use. This paper presents a comprehensive literature review of studies on finishing and strengthening technologies for the impeller and blisk of aero-engines. The review includes independent and integrated finishing and strengthening technologies and discusses advanced rotational abrasive flow machining with back-pressure used for finishing the integral impeller and blisk. A brief assessment of future research problems and directions is also presented.

The Infection Rate of Metal-on-Metal Total Hip Replacement Is Higher When Compared to Other Bearing Surfaces as Documented by the Australian Orthopaedic Association National Joint Replacement Registry.

PubMed

Huang, Phil; Lyons, Matt; O'Sullivan, Michael

2018-02-01

Despite the well-documented decline in the use of metal-on-metal (MoM) implants over the last decade, there are still controversies regarding whether all MoM implants are created equally. Complications such as elevated serum metal ion levels, aseptic lymphocyte-dominated vasculitis-associated lesion (ALVAL) and pseudotumours have all been well documented, but recent studies suggest increased risk of infection with MoM bearing surfaces. Most of these studies however have small patient numbers. The purpose of this study was to examine the cumulative incidence of revision for infection of MoM bearing surfaces in primary hip arthroplasty at a national and single-surgeon level. Data was collected from the Australian Orthopaedic Association National Joint Replacement Registry, which contains over 98% of all arthroplasties performed in Australia since 2001. The cumulative incidence of revision for infection was extracted at a national level and single-surgeon level. Two hundred seventy-six thousand eight hundred seventy-eight subjects were documented in the Australian registry. The 10-year cumulative percent revision for infection of MoM bearing surfaces in primary total hip replacement (THR) was 2.5% at a national level, compared to 0.8% for other bearing surfaces. The senior author contributed 1755 subjects with 7-year follow-up and a cumulative percent revision for infection of MoM bearing surfaces in primary THR of 36.9%, compared to 2.0% for other bearing surfaces. The cumulative percent of revision of MoM bearing surfaces is higher compared to other bearing surfaces; this is especially pronounced in cumulative percent of revision for infection. There was a higher cumulative percent of revision for infection in MoM bearings surfaces (in particular, large-head MoM) compared to other bearing surfaces at both the national and individual-surgeon level.

Growing-finishing performance and carcass characteristics of pigs fed normal and genetically modified low-phytate corn.

PubMed

Spencer, J D; Allee, G L; Sauber, T E

2000-06-01

A genetically modified corn hybrid homozygous for the lpa1 allele, containing low phytate (LP), and its nearly isogenic equivalent hybrid (normal) were compared in two experiments with growing-finishing swine. In Exp. 1, 210 barrows (27 kg) were allotted to one of six dietary treatments with two corn hybrids (LP and normal) and three P feeding regimens. There were five replicate pens (seven pigs/pen) per treatment. Treatments consisted of diets that were supplemented with P throughout the growing-finishing period (.2% P and .15% supplemental P during growing and finishing phases, respectively) or only during the growing phase (.2% supplemental P) or that were not supplemented with P throughout the growing-finishing period. Performance at the end of the growing phase was based on a 2 x 2 factorial arrangement of treatments with two corn hybrids and two levels of added P (0 and .2%). This resulted in 10 replicates for the treatments supplemented with .2% P. The finishing phase (73 to 112 kg) was a 2 x 3 factorial arrangement of treatments with the two types of corn and three regimens of added P during the finishing period. Breaking load (BL) and ash of the fourth metacarpal were evaluated from one pig/pen at the end of the growing phase and from all pigs after slaughter. Pigs fed the LP corn diet without added P had greater body weight gain, feed efficiency, BL, and ash content of the fourth metacarpal than pigs fed the normal corn diet without added P. Performance was similar between pigs fed the LP diet without added P and pigs fed LP and normal corn with added P. In Exp. 2, 1,092 gilts (34 kg body weight) were allotted by weight in a commercial facility to one of three treatments: 1) normal corn/soybean meal diet containing .29% and .22% available P during the growing and finishing phases, respectively; 2) LP corn/soybean meal diet with the same available P level as Treatment 1; and 3) same as Treatment 2 for 8 wk, then no inorganic P supplementation during the

Evaluate error correction ability of magnetorheological finishing by smoothing spectral function

NASA Astrophysics Data System (ADS)

Wang, Jia; Fan, Bin; Wan, Yongjian; Shi, Chunyan; Zhuo, Bin

2014-08-01

Power Spectral Density (PSD) has been entrenched in optics design and manufacturing as a characterization of mid-high spatial frequency (MHSF) errors. Smoothing Spectral Function (SSF) is a newly proposed parameter that based on PSD to evaluate error correction ability of computer controlled optical surfacing (CCOS) technologies. As a typical deterministic and sub-aperture finishing technology based on CCOS, magnetorheological finishing (MRF) leads to MHSF errors inevitably. SSF is employed to research different spatial frequency error correction ability of MRF process. The surface figures and PSD curves of work-piece machined by MRF are presented. By calculating SSF curve, the correction ability of MRF for different spatial frequency errors will be indicated as a normalized numerical value.

Marginal and internal discrepancies of zirconia copings: effects of milling system and finish line design.

PubMed

Ribeiro, Isabella Lima Arrais; Campos, Fernanda; Sousa, Rafael Santiago; Alves, Maria Luiza Lima; Rodrigues, Dalton Matos; Souza, Rodrigo Othavio Assuncão; Bottino, Marco Antonio

2015-01-01

Discrepancies at the abutment/crown interface can affect the longevity of zirconia restorations. The aim was to evaluate the marginal and internal discrepancies (MD and ID) of zirconia copings manufactured by two milling systems with different finish lines. Three aluminum-master-dies (h = 5.5 mm; Ψ =7.5 mm; 6΀), with different finish lines (large chamfer [LC]; tilted chamfer [TC]; rounded shoulder [RS]) were fabricated. Twenty impressions were made from each master die and poured. Sixty zirconia copings were manufactured and divided according to the factors "finish line" and "milling system" (n = 10): CAD LC = Computer-aided design/computer-aided manufacturing (CAD/CAM) + LC; CAD TC = CAD/CAM + TC; CAD RS = CAD/CAM + RS; MAD LC = manually aided design/manually aided manufacturing (MAD/MAM) + LC; MAD TC = MAD/MAM + TC; and MAD RS = MAD/MAM + RS. For MD analysis, each coping was fixed, and the distance between the external edges of the coping and the edge of the cervical preparation was measured (50 points). Using the same copings, the ID of each coping was evaluated, by the replica technique, at 12 points equally distributed among the regions (n = 10): Ray (R), axial (A), and occlusal (Occl). The measurements were performed by optical microscopy (Χ250). The data (μm) were subjected to parametric and non-parametric statistical analyses. For the MAD/MAM system, the "finish line" (P = 0.0001) affected significantly the MD median values (μm): LC = 251.80 a , RS = 68.40 a and TC = 8.10 b (Dunn's test). For the CAD/CAM system, the median MD values (μm) were not affected by the factor "finish line" (P = 0.4037): LC = 0.82 a , RS = 0.52 a , and TC = 0.89 a . For the ID, it was observed interaction between the finish line types and the region (P = 0.0001) and between region and milling system (P = 0.0031) (RM-ANOVA). The CAD/CAM system presented lower MD values, regardless the finish line. However, the MAD/MAM system showed ID values smaller than those of CAD/CAM.

Effects of roughage inclusion and particle size on performance and rumination behavior of finishing beef steers

USDA-ARS?s Scientific Manuscript database

Roughage is mechanically processed to increase digestibility, and handling and mixing characteristics in finishing diets. Roughage is fed to promote rumen health and decrease digestive upset, but inclusion in finishing diets is limited due to the cost per unit of energy. Rumination behavior may be a...

IMPLEMENTATION OF A CAPE-OPEN COMPLIANT PROCESS SIMULATOR USING MICROSOFT'S VISUAL STUDIO.NET AND THE .NET FRAMEWORK

EPA Science Inventory

The United States Environmental Protection Agency is developing a Computer
Aided Process Engineering (CAPE) software tool for the metal finishing
industry that helps users design efficient metal finishing processes that
are less polluting to the environment. Metal finish...

Occurrence of neonicotinoid insecticides in finished drinking water and fate during drinking water treatment

USGS Publications Warehouse

Klarich, Kathryn L.; Pflug, Nicholas C.; DeWald, Eden M.; Hladik, Michelle L.; Kolpin, Dana W.; Cwiertny, David M.; LeFevre, Gergory H.

2017-01-01

Neonicotinoid insecticides are widespread in surface waters across the agriculturally-intensive Midwestern US. We report for the first time the presence of three neonicotinoids in finished drinking water and demonstrate their general persistence during conventional water treatment. Periodic tap water grab samples were collected at the University of Iowa over seven weeks in 2016 (May-July) after maize/soy planting. Clothianidin, imidacloprid, and thiamethoxam were ubiquitously detected in finished water samples and ranged from 0.24-57.3 ng/L. Samples collected along the University of Iowa treatment train indicate no apparent removal of clothianidin and imidacloprid, with modest thiamethoxam removal (~50%). In contrast, the concentrations of all neonicotinoids were substantially lower in the Iowa City treatment facility finished water using granular activated carbon (GAC) filtration. Batch experiments investigated potential losses. Thiamethoxam losses are due to base-catalyzed hydrolysis at high pH conditions during lime softening. GAC rapidly and nearly completely removed all three neonicotinoids. Clothianidin is susceptible to reaction with free chlorine and may undergo at least partial transformation during chlorination. Our work provides new insights into the persistence of neonicotinoids and their potential for transformation during water treatment and distribution, while also identifying GAC as an effective management tool to lower neonicotinoid concentrations in finished drinking water.

40 CFR 425.10 - Applicability; description of the hair pulp, chrome tan, retan-wet finishing subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Applicability; description of the hair... POINT SOURCE CATEGORY Hair Pulp, Chrome Tan, Retan-Wet Finish Subcategory § 425.10 Applicability; description of the hair pulp, chrome tan, retan-wet finishing subcategory. The provisions of this subpart are...

40 CFR 425.20 - Applicability; description of the hair save, chrome tan, retan-wet finish subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 30 2011-07-01 2011-07-01 false Applicability; description of the hair... POINT SOURCE CATEGORY Hair Save, Chrome Tan, Retan-Wet Finish Subcategory § 425.20 Applicability; description of the hair save, chrome tan, retan-wet finish subcategory. The provisions of this subpart are...

Results from the Fourth Mathematics Assessment of the National Assessment of Educational Progress.

ERIC Educational Resources Information Center

Lindquist, Mary Montgomery, Ed.

The National Assessment of Educational Progress (NAEP) completed its fourth mathematics assessment during the 1985-86 school year and finished the analyses of the results in 1988. This monograph, prepared by an interpretive team of the National Council of Teachers of Mathematics, represents a comprehensive discussion of the results of the fourth…

Lathe Attachment Finishes Inner Surface of Tubes

NASA Technical Reports Server (NTRS)

Lancki, A. J.

1982-01-01

Extremely smooth finishes are machined on inside surfaces of tubes by new attachment for a lathe. The relatively inexpensive accessory, called a "microhone," holds a honing stone against workpiece by rigid tangs instead of springs as in conventional honing tools. Inner rod permits adjustment of microhoning stone, while outer tube supports assembly. Outer tube is held between split blocks on lathe toolpost. Microhoning can be done with either microhone or workpiece moving and other member stationary.

40 CFR 463.30 - Applicability; description of the finishing water subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) PLASTICS MOLDING AND FORMING POINT SOURCE CATEGORY.... Processes in the finishing water subcategory are processes where water comes in contact with the plastic...

40 CFR 463.30 - Applicability; description of the finishing water subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS (CONTINUED) PLASTICS MOLDING AND FORMING POINT SOURCE CATEGORY.... Processes in the finishing water subcategory are processes where water comes in contact with the plastic...

Investigations of the Impact of Biodiesel Metal Contaminants on Emissions Control Devices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brookshear, Daniel W; Lance, Michael J; Mccormick, Robert

Biodiesel is a renewable fuel with the potential to displace a portion of petroleum use. However, as with any alternative fuel, in order to be a viable choice it must be compatible with the emissions control devices. The finished biodiesel product can contain up to 5 ppm Na + K and 5 ppm Ca + Mg, and these metal impurities can lead to durability issues with the devices used to control emissions in diesel vehicles. Significant work has been performed to understand how the presence of these metals impacts each individual component of diesel emissions control systems, and this chaptermore » summarizes the findings of these research efforts.« less

Investigations of the Impact of Biodiesel Metal Contaminants on Emissions Control Devices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brookshear, D. W.; Lance, M. J.; McCormick, Robert L.

Biodiesel is a renewable fuel with the potential to displace a portion of petroleum use. However, as with any alternative fuel, in order to be a viable choice it must be compatible with the emissions control devices. The finished biodiesel product can contain up to 5 ppm Na+K and 5 ppm Ca+Mg, and these metal impurities can lead to durability issues with the devices used to control emissions in diesel vehicles. Significant work has been performed to understand how the presence of these metals impacts each individual component of diesel emissions control systems, and this chapter summarizes the findings ofmore » these research efforts.« less

40 CFR 425.10 - Applicability; description of the hair pulp, chrome tan, retan-wet finishing subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Applicability; description of the hair pulp, chrome tan, retan-wet finishing subcategory. 425.10 Section 425.10 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING POINT SOURCE CATEGORY Hair Pulp, Chrome...

40 CFR 425.20 - Applicability; description of the hair save, chrome tan, retan-wet finish subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Applicability; description of the hair save, chrome tan, retan-wet finish subcategory. 425.20 Section 425.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING POINT SOURCE CATEGORY Hair Save, Chrome Tan,...

2. DETAIL VIEW OF JOURNAL LATHE, AXLE FINISHING AREA. Grinding ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. DETAIL VIEW OF JOURNAL LATHE, AXLE FINISHING AREA. Grinding bearing diameters on locomotive axle. Norton grinder, 1942 (dated). Melvin Grassmeyer, operator. - Juniata Shops, Machine Shop No. 1, East of Fourth Avenue at Third Street, Altoona, Blair County, PA

3. DETAIL VIEW OF JOURNAL LATHE, AXLE FINISHING AREA. Grinding ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. DETAIL VIEW OF JOURNAL LATHE, AXLE FINISHING AREA. Grinding bearing diameters on locomotive axle. Norton grinder, 1942 (dated). Melvin Grassmeyer, operator. - Juniata Shops, Machine Shop No. 1, East of Fourth Avenue at Third Street, Altoona, Blair County, PA

A survey of grass-finished beef producers in Pennsylvania

USDA-ARS?s Scientific Manuscript database

To meet our goal of quantifying the environmental impacts of grass-finished beef production, data on production practices in Pennsylvania were collected at the farm level via visits and online surveys. Twenty-three responses represented a total of 1,055 animals on 2,155 acres of land. Farms were rel...

Cement Finishing. Pre-Apprenticeship Phase 2 Training. Instructor's Guide.

ERIC Educational Resources Information Center

Nama, Joe

This instructor's guide accompanies the self-paced student training modules on cement finishing, available separately as CE 031 576. Introductory materials include a description of the components of the pre-apprenticeship project, discussion of teacher's role in students' completion of the modules, and scope and contents of Phase 2 training. Each…

Effects of winter stocker growth rate and finishing system on: III. Tissue proximate, fatty acid, vitamin, and cholesterol content.

PubMed

Duckett, S K; Neel, J P S; Fontenot, J P; Clapham, W M

2009-09-01

Angus-cross steers (n = 198; 270 kg of BW; 8 mo) were used in a 3-yr study to assess the effects of winter stocker growth rate and finishing system on LM proximate, fatty acid, cholesterol, vitamin, and mineral composition. During the winter months (December to April), steers were randomly allotted to 3 stocker growth rates: low (0.23 kg/d), medium (0.45 kg/d), or high (0.68 kg/d). At the completion of the stockering phase, steers were allotted randomly within each stocker growth rate to a high concentrate (CONC) or pasture (PAST) finishing system and finished to an equal time endpoint. Winter stocker growth rate did not alter (P > 0.05) proximate, cholesterol, or vitamin content of the LM. All interactions among winter stocker growth rate and finishing system were nonsignificant, indicating that supplementation systems during winter stocker period did not influence beef composition after finishing on PAST or CONC. Finishing steers on CONC decreased (P < 0.001) moisture content of the LM and increased (P < 0.001) lipid content of the LM. Protein, ash, and cholesterol content of the LM did not differ (P > 0.05) between finishing systems. alpha-Tocopherol and beta-carotene content of the LM were 288 and 54% greater, respectively, for PAST-finished cattle than CONC. B-vitamins, thiamine and riboflavin, were also present in greater (P = 0.001) concentrations for PAST than CONC. Calcium, Mg, and K contents of the LM were greater (P < 0.05) for PAST than CONC. Total fatty acid content of the LM was 49% less for PAST than CONC. Myristoleic, palmitoleic, and oleic acid concentrations were all less (P = 0.001) for PAST than CONC. Trans-10 octadecenoic acid percentage in LM was 97% greater (P = 0.001) for CONC than PAST; conversely, trans-11 vaccenic acid percentage in the LM was 90% greater (P = 0.001) for PAST than CONC. Conjugated linoleic acid, cis-9, trans-11 isomer, percentage was greater (P = 0.001) by 117% for PAST than CONC. Linoleic acid (C18:2) concentration did

A Case Study into Microbial Genome Assembly Gap Sequences and Finishing Strategies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Utturkar, Sagar M.; Klingeman, Dawn M.; Hurt, Jr., Richard A.

This study characterized regions of DNA which remained unassembled by either PacBio and Illumina sequencing technologies for seven bacterial genomes. Two genomes were manually finished using bioinformatics and PCR/Sanger sequencing approaches and regions not assembled by automated software were analyzed. Gaps present within Illumina assemblies mostly correspond to repetitive DNA regions such as multiple rRNA operon sequences. PacBio gap sequences were evaluated for several properties such as GC content, read coverage, gap length, ability to form strong secondary structures, and corresponding annotations. Our hypothesis that strong secondary DNA structures blocked DNA polymerases and contributed to gap sequences was not accepted.more » PacBio assemblies had few limitations overall and gaps were explained as cumulative effect of lower than average sequence coverage and repetitive sequences at contig termini. An important aspect of the present study is the compilation of biological features that interfered with assembly and included active transposons, multiple plasmid sequences, phage DNA integration, and large sequence duplication. Furthermore, our targeted genome finishing approach and systematic evaluation of the unassembled DNA will be useful for others looking to close, finish, and polish microbial genome sequences.« less

A Case Study into Microbial Genome Assembly Gap Sequences and Finishing Strategies

DOE PAGES

Utturkar, Sagar M.; Klingeman, Dawn M.; Hurt, Jr., Richard A.; ...

2017-07-18

This study characterized regions of DNA which remained unassembled by either PacBio and Illumina sequencing technologies for seven bacterial genomes. Two genomes were manually finished using bioinformatics and PCR/Sanger sequencing approaches and regions not assembled by automated software were analyzed. Gaps present within Illumina assemblies mostly correspond to repetitive DNA regions such as multiple rRNA operon sequences. PacBio gap sequences were evaluated for several properties such as GC content, read coverage, gap length, ability to form strong secondary structures, and corresponding annotations. Our hypothesis that strong secondary DNA structures blocked DNA polymerases and contributed to gap sequences was not accepted.more » PacBio assemblies had few limitations overall and gaps were explained as cumulative effect of lower than average sequence coverage and repetitive sequences at contig termini. An important aspect of the present study is the compilation of biological features that interfered with assembly and included active transposons, multiple plasmid sequences, phage DNA integration, and large sequence duplication. Furthermore, our targeted genome finishing approach and systematic evaluation of the unassembled DNA will be useful for others looking to close, finish, and polish microbial genome sequences.« less

A Case Study into Microbial Genome Assembly Gap Sequences and Finishing Strategies.

PubMed

Utturkar, Sagar M; Klingeman, Dawn M; Hurt, Richard A; Brown, Steven D

2017-01-01

This study characterized regions of DNA which remained unassembled by either PacBio and Illumina sequencing technologies for seven bacterial genomes. Two genomes were manually finished using bioinformatics and PCR/Sanger sequencing approaches and regions not assembled by automated software were analyzed. Gaps present within Illumina assemblies mostly correspond to repetitive DNA regions such as multiple rRNA operon sequences. PacBio gap sequences were evaluated for several properties such as GC content, read coverage, gap length, ability to form strong secondary structures, and corresponding annotations. Our hypothesis that strong secondary DNA structures blocked DNA polymerases and contributed to gap sequences was not accepted. PacBio assemblies had few limitations overall and gaps were explained as cumulative effect of lower than average sequence coverage and repetitive sequences at contig termini. An important aspect of the present study is the compilation of biological features that interfered with assembly and included active transposons, multiple plasmid sequences, phage DNA integration, and large sequence duplication. Our targeted genome finishing approach and systematic evaluation of the unassembled DNA will be useful for others looking to close, finish, and polish microbial genome sequences.

A Case Study into Microbial Genome Assembly Gap Sequences and Finishing Strategies

PubMed Central

Utturkar, Sagar M.; Klingeman, Dawn M.; Hurt, Richard A.; Brown, Steven D.

2017-01-01

This study characterized regions of DNA which remained unassembled by either PacBio and Illumina sequencing technologies for seven bacterial genomes. Two genomes were manually finished using bioinformatics and PCR/Sanger sequencing approaches and regions not assembled by automated software were analyzed. Gaps present within Illumina assemblies mostly correspond to repetitive DNA regions such as multiple rRNA operon sequences. PacBio gap sequences were evaluated for several properties such as GC content, read coverage, gap length, ability to form strong secondary structures, and corresponding annotations. Our hypothesis that strong secondary DNA structures blocked DNA polymerases and contributed to gap sequences was not accepted. PacBio assemblies had few limitations overall and gaps were explained as cumulative effect of lower than average sequence coverage and repetitive sequences at contig termini. An important aspect of the present study is the compilation of biological features that interfered with assembly and included active transposons, multiple plasmid sequences, phage DNA integration, and large sequence duplication. Our targeted genome finishing approach and systematic evaluation of the unassembled DNA will be useful for others looking to close, finish, and polish microbial genome sequences. PMID:28769883

Physical and nutritional properties of buffalo meat finished on hay or maize silage-based diets.

PubMed

Cifuni, Giulia Francesca; Contò, Michela; Amici, Andrea; Failla, Sebastiana

2014-04-01

The current study examines the effect of different finishing diets (hay- vs. maize-silage on meal ration) on carcass quality, physical, chemical and sensory properties, and fatty acid profiles of buffalo meat. Twenty male Italian Mediterranean buffaloes (246 ± 9.00 kg live weight) were distributed at random into two groups at the beginning of the finishing period (368 ± 20 days). The buffaloes were offered two finishing diets: a maize silage (MS) or an alfalfa hay (AH) diet. No significant differences were found between dietary treatments for live and carcass weight. Meat chemical composition was influenced by dietary treatment. A higher fat content was detected in meat from animals finished with MS than AH (P < 0.05). Overall, the data indicated differences between the fatty acid profiles of meat as a consequence of different feeding systems. The higher fat deposition in the MS group resulted in meat with a less favorable fatty acid profile (i.e. a lower polyunsaturated/saturated fatty acid ratio and α-linolenic fatty acid content) in relation to human health compared with meat from animals fed the AH diet. © 2013 Japanese Society of Animal Science.

Combined Advanced Finishing and UV-Laser Conditioning for Producing UV-Damage-Resistant Fused Silica Optics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menapace, J A; Penetrante, B; Golini, D

2001-11-01

Laser induced damage initiation on fused silica optics can limit the lifetime of the components when used in high power UV laser environments. Foe example in inertial confinement fusion research applications, the optics can be exposed to temporal laser pulses of about 3-nsec with average fluences of 8 J/cm{sup 2} and peak fluences between 12 and 15 J/cm{sup 2}. During the past year, we have focused on optimizing the damage performance at a wavelength of 355-nm (3{omega}), 3-nsec pulse length, for optics in this category by examining a variety of finishing technologies with a challenge to improve the laser damagemore » initiation density by at least two orders of magnitude. In this paper, we describe recent advances in improving the 3{omega} damage initiation performance of laboratory-scale zirconium oxide and cerium oxide conventionally finished fused silica optics via application of processes incorporating magnetorheological finishing (MRF), wet chemical etching, and UV laser conditioning. Details of the advanced finishing procedures are described and comparisons are made between the procedures based upon large area 3{omega} damage performance, polishing layer contamination, and optical subsurface damage.« less

Choice of crystal surface finishing for a dual-ended readout depth-of-interaction (DOI) detector.

PubMed

Fan, Peng; Ma, Tianyu; Wei, Qingyang; Yao, Rutao; Liu, Yaqiang; Wang, Shi

2016-02-07

The objective of this study was to choose the crystal surface finishing for a dual-ended readout (DER) DOI detector. Through Monte Carlo simulations and experimental studies, we evaluated 4 crystal surface finishing options as combinations of crystal surface polishing (diffuse or specular) and reflector (diffuse or specular) options on a DER detector. We also tested one linear and one logarithm DOI calculation algorithm. The figures of merit used were DOI resolution, DOI positioning error, and energy resolution. Both the simulation and experimental results show that (1) choosing a diffuse type in either surface polishing or reflector would improve DOI resolution but degrade energy resolution; (2) crystal surface finishing with a diffuse polishing combined with a specular reflector appears a favorable candidate with a good balance of DOI and energy resolution; and (3) the linear and logarithm DOI calculation algorithms show overall comparable DOI error, and the linear algorithm was better for photon interactions near the ends of the crystal while the logarithm algorithm was better near the center. These results provide useful guidance in DER DOI detector design in choosing the crystal surface finishing and DOI calculation methods.

Management Characteristics of Grass-finished Beef Operations in the Northeast

USDA-ARS?s Scientific Manuscript database

An online survey of self-identified grass-finished beef producers was conducted throughout the Northeast region along with several farm visits. Seventy acceptable records from producers in Delaware, Maine, Massachusetts, Maryland, New Hampshire, New Jersey, New York, Pennsylvania, Vermont, and West ...

Effects of Fiber Finish on Mechanical, Low and High Speed Impact of Glass Fiber Reinforced Composites

DTIC Science & Technology

2011-05-12

For 70 Min Cool Down And De-mold 10Unclassified For Producing Polyester Or Vinyl Ester Composite Specimens Resin Resin Inlet Vacuum Bag Trap Pump Steel...Reinforcement Finish Matrix Fiber Content (%) Hexcel 1581-F12 Heat Burnt (No Finish) PP 71.0 Polyester 70.0 Vinyl ester 66.2 Hexcel 1581-GR Greige ( Starch

77 FR 39997 - Heavy Forged Hand Tools, Finished or Unfinished, With or Without Handles From the People's...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-06

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-803] Heavy Forged Hand Tools... review on heavy forged hand tools, finished or unfinished, with or without handles from the People's..., 2012) (Tianjin v. United States). \\2\\ See Heavy Forged Hand Tools, Finished or Unfinished, With or...

Method and means for producing fluorocarbon finishes on fibrous structures

NASA Technical Reports Server (NTRS)

Toy, Madeline S. (Inventor); Stringham, Roger S. (Inventor); Fogg, Lawrence C. (Inventor)

1981-01-01

An improved process and apparatus is provided for imparting chemically bonded fluorocarbon finishes to textiles. In the process, the textiles are contacted with a gaseous mixture of fluoroolefins in an inert diluent gas in the presence of ultraviolet light under predetermined conditions.

78 FR 23591 - Certain Prepregs, Laminates, and Finished Circuit Boards

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-19

... INTERNATIONAL TRADE COMMISSION [Investigation No. 337-TA-659 (Enforcement)] Certain Prepregs... United States after importation of certain prepregs, laminates, and finished circuit boards that infringe... prepregs and laminates that are the subject of the investigation or that otherwise infringe, induce, and/or...

The influence of surface finishing methods on touch-sensitive reactions

NASA Astrophysics Data System (ADS)

Kukhta, M. S.; Sokolov, A. P.; Krauinsh, P. Y.; Kozlova, A. D.; Bouchard, C.

2017-02-01

This paper describes the modern technological development trends in jewelry design. In the jewelry industry, new trends, associated with the introduction of updated non-traditional materials and finishing techniques, are appearing. The existing information-oriented society enhances the visual aesthetics of new jewelry forms, decoration techniques (depth and surface), synthesis of different materials, which, all in all, reveal a bias towards positive effects of visual design. Today, the jewelry industry includes not only traditional techniques, but also such improved techniques as computer-assisted design, 3D-prototyping and other alternatives to produce an updated level of jewelry material processing. The authors present the specific features of ornamental pattern designing, decoration types (depth and surface) and comparative analysis of different approaches in surface finishing. Identifying the appearance or the effect of jewelry is based on proposed evaluation criteria, providing an advanced visual aesthetics basis is predicated on touch-sensitive responses.

Method and system for processing optical elements using magnetorheological finishing

DOEpatents

Menapace, Joseph Arthur; Schaffers, Kathleen Irene; Bayramian, Andrew James; Molander, William A

2012-09-18

A method of finishing an optical element includes mounting the optical element in an optical mount having a plurality of fiducials overlapping with the optical element and obtaining a first metrology map for the optical element and the plurality of fiducials. The method also includes obtaining a second metrology map for the optical element without the plurality of fiducials, forming a difference map between the first metrology map and the second metrology map, and aligning the first metrology map and the second metrology map. The method further includes placing mathematical fiducials onto the second metrology map using the difference map to form a third metrology map and associating the third metrology map to the optical element. Moreover, the method includes mounting the optical element in the fixture in an MRF tool, positioning the optical element in the fixture; removing the plurality of fiducials, and finishing the optical element.

Biosynthesis of silver nanoparticles using lemon leaves extract and its application for antimicrobial finish on fabric

NASA Astrophysics Data System (ADS)

Vankar, Padma S.; Shukla, Dhara

2012-06-01

Preparation of silver nanoparticles have been carried out using aqueous extract of lemon leaves ( Citrus limon) which acts as reducing agent and encapsulating cage for the silver nanoparticles. These silver nanoparticles have been used for durable textile finish on cotton and silk fabrics. Remarkable antifungal activity has been observed in the treated fabrics. The antimicrobial activity of silver nanoparticles derived from lemon leaves showed enhancement in activity due to synergistic effect of silver and essential oil components of lemon leaves. The present investigation shows the extracellular synthesis of highly stable silver nanoparticles by biotransformation using the extract of lemon leaves by controlled reduction of the Ag+ ion to Ag0. Further the silver nanoparticles were used for antifungal treatment of fabrics which was tested by antifungal activity assessment of textile material by Agar diffusion method against Fusarium oxysporum and Alternaria brassicicola. Formation of the metallic nanoparticles was established by FT-IR, UV-Visible spectroscopy, transmission electron microscopy, scanning electron microscopy, atomic force microscopy.

Military Curriculum Materials for Vocational and Technical Education. Builders School, Finish Carpentry I. Classroom Course 3-10.

ERIC Educational Resources Information Center

Ohio State Univ., Columbus. National Center for Research in Vocational Education.

Adapted from military service training materials, this publication contains course materials for teaching finish carpentry, both in the classroom and through practical experience. Students completing this short course will be able to finish carpentry projects involving wallboard, plywood panel, composition floor tile, and acoustical ceiling tile.…

77 FR 2031 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished From the People's Republic of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-13

... Parts Thereof, Finished and Unfinished From the People's Republic of China: Extension of the Time Limit..., International Trade Administration, U.S. Department of Commerce, 14th Street and Constitution Avenue NW..., finished and unfinished from the People's Republic of China. See Tapered Roller Bearings and Parts Thereof...

Ductile Damage and Fatigue Behavior of Semi-Finished Tailored Blanks for Sheet-Bulk Metal Forming Processes

NASA Astrophysics Data System (ADS)

Besserer, Hans-Bernward; Hildenbrand, Philipp; Gerstein, Gregory; Rodman, Dmytro; Nürnberger, Florian; Merklein, Marion; Maier, Hans Jürgen

2016-03-01

To produce parts from sheet metal with thickened functional elements, bulk forming operations can be employed. For this new process class, the term sheet-bulk metal forming has been established recently. Since sheet-bulk metal forming processes such as orbital forming generates triaxial stress and strain states, ductile damage is induced in the form of voids in the microstructure. Typical parts will experience cyclic loads during service, and thus, the influence of ductile damage on the fatigue life of parts manufactured by orbital forming is of interest. Both the formation and growth of voids were characterized following this forming process and then compared to the as-received condition of the ferritic deep drawing steel DC04 chosen for this study. Subsequent to the forming operation, the specimens were fatigued and the evolution of ductile damage and the rearrangement of the dislocation networks occurring during cyclic loading were determined. It was shown, that despite an increased ductile damage due to the forming process, the induced strain hardening has a positive effect on the fatigue life of the material. However, by analyzing the fatigued specimens a development of the ductile damage by an increasing number of voids and a change in the void shape were detected.

Carpentry and Finishing Procedures. Building Maintenance. Module II. Instructor's Guide.

ERIC Educational Resources Information Center

Hawk, Sam; Brunk, Art

This curriculum guide, keyed to the building maintenance competency profile developed by industry and education professionals, provides three units on carpentry and finishing procedures. The first unit, Exterior Carpentry, contains the following lessons: carpentry safety procedures, ladder and scaffolding safety, door installation/repair,…

Material removal in magnetorheological finishing of optics.

PubMed

Kordonski, William; Gorodkin, Sergei

2011-05-10

A concept of material removal based on the principle of conservation of particles momentum in a binary suspension is applied to analyze material removal in magnetorheological finishing and magnetorheological jet processes widely used in precision optics fabrication. According to this concept, a load for surface indentation by abrasive particles is provided at their interaction near the wall with heavier basic (magnetic) particles, which fluctuate (due to collision) in the shear flow of concentrated suspension. The model is in good qualitative and quantitative agreement with experimental results.

76 FR 69241 - Tapered Roller Bearings and Parts Thereof, Finished or Unfinished, From the People's Republic of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-08

... Parts Thereof, Finished or Unfinished, From the People's Republic of China: Extension of Time Limit for... and parts thereof, finished or unfinished, (``TRBs'') from the People's Republic of China (``PRC... Revocation in Part, 75 FR 44224 (July 28, 2010). On July 13, 2011, the Department published the preliminary...

Additive manufacturing of reflective optics: evaluating finishing methods

NASA Astrophysics Data System (ADS)

Leuteritz, G.; Lachmayer, R.

2018-02-01

Individually shaped light distributions become more and more important in lighting technologies and thus the importance of additively manufactured reflectors increases significantly. The vast field of applications ranges from automotive lighting to medical imaging and bolsters the statement. However, the surfaces of additively manufactured reflectors suffer from insufficient optical properties even when manufactured using optimized process parameters for the Selective Laser Melting (SLM) process. Therefore post-process treatments of reflectors are necessary in order to further enhance their optical quality. This work concentrates on the effectiveness of post-process procedures for reflective optics. Based on already optimized aluminum reflectors, which are manufactured with a SLM machine, the parts are differently machined after the SLM process. Selected finishing methods like laser polishing, sputtering or sand blasting are applied and their effects quantified and compared. The post-process procedures are investigated on their impact on surface roughness and reflectance as well as geometrical precision. For each finishing method a demonstrator will be created and compared to a fully milled sample and among themselves. Ultimately, guidelines are developed in order to figure out the optimal treatment of additively manufactured reflectors regarding their optical and geometrical properties. Simulations of the light distributions will be validated with the developed demonstrators.

Heterosis for meat quality and fatty acid profiles in crosses among Bos indicus and Bos taurus finished on pasture or grain.

PubMed

Gama, L T; Bressan, M C; Rodrigues, E C; Rossato, L V; Moreira, O C; Alves, S P; Bessa, R J B

2013-01-01

Physicochemical properties and fatty acid profiles of meat from Bos indicus, Bos taurus and crossbred B. taurus×B. indicus bullocks (n=216), finished on pasture or grain, were used to estimate the effects of heterosis. Meat quality and fatty acid profiles generally benefited with crossbreeding, but the advantages from heterosis differed among finishing systems. The Warner-Bratzler shear-force in fresh and aged meat was reduced due to heterosis in pasture-finishing, but the effect was minor under grain-finishing. With pasture-finishing, heterosis caused an increase of 5% in CLA concentration, but few other changes in fatty acid profiles. In grain-finishing, heterosis caused a reduction in intramuscular fat and cholesterol, increased amounts of PUFA, n-6 fatty acids and PUFA/SFA ratio, and a decline in atherogenic index. The Δ(9) desaturase estimated activity in crossbreds showed a behavior close to B. indicus, suggesting the existence of few loci and a dominance genetic effect on enzymes involved in fatty acid synthesis and metabolism. Copyright © 2012 Elsevier Ltd. All rights reserved.

78 FR 34985 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished From the People's Republic of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-11

... Parts Thereof, Finished and Unfinished From the People's Republic of China: Rescission, in Part, of... parts thereof, finished and unfinished (TRBs) from the People's Republic of China (PRC) covering the... section 771(9)(A) of the Act, as amended, Dana Off Highway Products, LLC, for the company Timken de Mexico...

Analyzing and improving surface texture by dual-rotation magnetorheological finishing

NASA Astrophysics Data System (ADS)

Wang, Yuyue; Zhang, Yun; Feng, Zhijing

2016-01-01

The main advantages of magnetorheological finishing (MRF) are its high convergence rate of surface error, the ability of polishing aspheric surfaces and nearly no subsurface damage. However, common MRF produces directional surface texture due to the constant flow direction of the magnetorheological (MR) polishing fluid. This paper studies the mechanism of surface texture formation by texture modeling. Dual-rotation magnetorheological finishing (DRMRF) is presented to suppress directional surface texture after analyzing the results of the texture model for common MRF. The results of the surface texture model for DRMRF and the proposed quantitative method based on mathematical statistics indicate the effective suppression of directional surface texture. An experimental setup is developed and experiments show directional surface texture and no directional surface texture in common MRF and DRMRF, respectively. As a result, the surface roughness of DRMRF is 0.578 nm (root-mean-square value) which is lower than 1.109 nm in common MRF.

Frictional forces in material removal for glasses and ceramics using magnetorheological finishing

NASA Astrophysics Data System (ADS)

Miao, Chunlin

Magnetorheological finishing (MRF) spotting experiments on stationary parts are conducted in this work to understand the material removal mechanism in MRF. Drag force and normal force are measured in situ, simultaneously for the first time for a variety of optical materials in MRF. We study material removal process in MRF as a function of material mechanical properties. We experimentally demonstrate that material removal in MRF is strongly related to shear stress. Shear stress is predominantly determined by material mechanical properties. A modified Preston's equation is proposed to estimate the material removal in MRF by combining shear stress and material mechanical properties. We investigate extensively the effect of various MRF process parameters, including abrasive concentration, magnetic field strength, penetration depth and wheel speed, on material removal efficiency. Material removal rate model is expanded to include these parameters. We develop a nonaqueous magnetorheological (MR) fluid for examining the mechanical contribution in MRF material removal. This fluid is based on a combination of two CI particles and a combination of two organic liquids. Material removal with this nonaqueous MR fluid is discussed. We formulate a new corrosion resistant MR fluid which is based on metal oxide coated carbonyl iron (CI) particles. The rheological behavior, stability and corrosion resistance are examined.

75 FR 9391 - Tapered Roller Bearings and Parts Thereof, Finished or Unfinished, from the People's Republic of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-02

... Parts Thereof, Finished or Unfinished, from the People's Republic of China: Extension of Time Limit for... review of the antidumping duty order on tapered roller bearings and parts thereof, finished or unfinished... March 9, 2010. Statutory Time Limits Section 751(a)(3)(A) of the Tariff Act of 1930, as amended (``the...

The association between measurements of antimicrobial use and resistance in the faeces microbiota of finisher batches.

PubMed

Andersen, V D; DE Knegt, L V; Munk, P; Jensen, M S; Agersø, Y; Aarestrup, F M; Vigre, H

2017-10-01

The objectives were to present three approaches for calculating antimicrobial (AM) use in pigs that take into account the rearing period and rearing site, and to study the association between these measurements and phenotypical resistance and abundance of resistance genes in faeces samples from 10 finisher batches. The AM use was calculated relative to the rearing period of the batches as (i) 'Finisher Unit Exposure' at unit level, (ii) 'Lifetime Exposure' at batch level and (iii) 'Herd Exposure' at herd level. A significant effect on the occurrence of tetracycline resistance measured by cultivation was identified for Lifetime Exposure for the AM class: tetracycline. Furthermore, for Lifetime Exposure for the AM classes: macrolide, broad-spectrum penicillin, sulfonamide and tetracycline use as well as Herd Unit Exposure for the AM classes: aminoglycoside, lincosamide and tetracycline use, a significant effect was observed on the occurrence of genes coding for the AM resistance classes: aminoglycoside, lincosamide, macrolide, β-lactam, sulfonamide and tetracycline. No effect was observed for Finisher Unit Exposure. Overall, the study shows that Lifetime Exposure is an efficient measurement of AM use in finisher batches, and has a significant effect on the occurrence of resistance, measured either by cultivation or metagenomics.

7 CFR 58.344 - Storage of finished product in freezer.

Code of Federal Regulations, 2012 CFR

2012-01-01

... maintained at −10 °F. or lower and shall be equipped to provide sufficient high velocity, air circulation for rapid freezing. After the products have been completely frozen, they may be transferred to a freezer..., if necessary, at a later time. Requirements for Finished Products Bearing USDA Official...

7 CFR 58.344 - Storage of finished product in freezer.

Code of Federal Regulations, 2010 CFR

2010-01-01

... maintained at −10 °F. or lower and shall be equipped to provide sufficient high velocity, air circulation for rapid freezing. After the products have been completely frozen, they may be transferred to a freezer..., if necessary, at a later time. Requirements for Finished Products Bearing USDA Official...

7 CFR 58.344 - Storage of finished product in freezer.

Code of Federal Regulations, 2011 CFR

2011-01-01

... maintained at −10 °F. or lower and shall be equipped to provide sufficient high velocity, air circulation for rapid freezing. After the products have been completely frozen, they may be transferred to a freezer..., if necessary, at a later time. Requirements for Finished Products Bearing USDA Official...

7 CFR 58.344 - Storage of finished product in freezer.

Code of Federal Regulations, 2013 CFR

2013-01-01

... maintained at −10 °F. or lower and shall be equipped to provide sufficient high velocity, air circulation for rapid freezing. After the products have been completely frozen, they may be transferred to a freezer..., if necessary, at a later time. Requirements for Finished Products Bearing USDA Official...

7 CFR 58.344 - Storage of finished product in freezer.

Code of Federal Regulations, 2014 CFR

2014-01-01

... maintained at −10 °F. or lower and shall be equipped to provide sufficient high velocity, air circulation for rapid freezing. After the products have been completely frozen, they may be transferred to a freezer..., if necessary, at a later time. Requirements for Finished Products Bearing USDA Official...

Risk assessment of allergen metals in cosmetic products.

PubMed

Sipahi, Hande; Charehsaz, Mohammad; Güngör, Zerrin; Erdem, Onur; Soykut, Buğra; Akay, Cemal; Aydin, Ahmet

2015-01-01

Cosmetics are one of the most common reasons for hospital referrals with allergic contact dermatitis. Because of the increased use of cosmetics within the population and an increase in allergy cases, monitoring of heavy metals, especially allergen metals, is crucial. The aim of this study was to investigate the concentration of allergen metals, nickel (Ni), cobalt (Co), and chromium (Cr), in the most commonly used cosmetic products including mascara, eyeliner, eye shadow, lipstick, and nail polish. In addition, for safety assessment of cosmetic products, margin of safety of the metals was evaluated. Forty-eight makeup products were purchased randomly from local markets and large cosmetic stores in Istanbul, Turkey, and an atomic absorption spectrometer was used for metal content determination. Risk assessment of the investigated cosmetic products was performed by calculating the systemic exposure dosage (SED) using Scientific Committee on Consumer Safety guideline. According to the results of this investigation in all the samples tested, at least two of the allergen metals, Ni and/or Co and/or Cr were detected. Moreover, 97% of the Ni-detected products, 96% of Cr- and 54% of Co-detected products, contained over 1 μg/g of this metals, which is the suggested ultimate target value for sensitive population and thereby can be considered as the possible allergen. On the basis of the results of this study, SED of the metals was negligible; however, contact dermatitis caused by cosmetics is most probably due to the allergen metal content of the products. In conclusion, to assess the safety of the finished products, postmarketing vigilance and routine monitoring of allergen metals are very important to protect public health.

Weathering steel as a potential source for metal contamination: Metal dissolution during 3-year of field exposure in a urban coastal site.

PubMed

Raffo, Simona; Vassura, Ivano; Chiavari, Cristina; Martini, Carla; Bignozzi, Maria C; Passarini, Fabrizio; Bernardi, Elena

2016-06-01

Surface and building runoff can significantly contribute to the total metal loading in urban runoff waters, with potential adverse effects on the receiving ecosystems. The present paper analyses the corrosion-induced metal dissolution (Fe, Mn, Cr, Ni, Cu) from weathering steel (Cor-Ten A) with or without artificial patinas, exposed for 3 years in unsheltered conditions at a marine urban site (Rimini, Italy). The influence of environmental parameters, atmospheric pollutants and surface finish on the release of dissolved metals in rain was evaluated, also by means of multivariate analysis (two-way and three-way Principal Component Analysis). In addition, surface and cross-section investigations were performed so as to monitor the patina evolution. The contribution provided by weathering steel runoff to the dissolved Fe, Mn and Ni loading at local level is not negligible and pre-patination treatments seem to worsen the performance of weathering steel in term of metal release. Metal dissolution is strongly affected by extreme events and shows seasonal variations, with different influence of seasonal parameters on the behaviour of bare or artificially patinated steel, suggesting that climate changes could significantly influence metal release from this alloy. Therefore, it is essential to perform a long-term monitoring of the performance, the durability and the environmental impact of weathering steel. Copyright © 2016 Elsevier Ltd. All rights reserved.

Magnetic susceptibility as an indicator of heavy metal contamination in compost.

PubMed

Paradelo, Remigio; Moldes, Ana Belén; Barral, María Teresa

2009-02-01

One of the main restrictions to the agronomic use of compost is the excess of heavy metals, which are often present due to inadequate separation of biodegradable fractions from non-degradable or inert materials. Magnetic susceptibility (MS) measurements are a simple technique that has been reported as a useful tool for assessing anthropogenic pollution, especially heavy metal pollution on soil and sediment samples. The close relationship of MS with heavy metal contamination has been proved by combined analyses of chemical and magnetic data. In this study, the MS and total heavy metal concentrations of eight composts from different origins were determined; all composts were passed under a magnet to remove the magnetic material, and total heavy metals were determined again. In our work, high correlations were found between magnetic susceptibility and total Cd, Zn, Pb, Cr and Ni, thus confirming the applicability of MS measurement as a proxy for heavy metal contamination in compost quality assessments. The application of a magnet over the composts reduced the MS as well as the heavy metal content, the reduction of Fe and MS being the most significantly correlated. Thus, the inclusion of an additional magnetic separation step in the post-process compost finishing could be envisaged.

Relationship between influence function accuracy and polishing quality in magnetorheological finishing

NASA Astrophysics Data System (ADS)

Schinhaerl, Markus; Schneider, Florian; Rascher, Rolf; Vogt, Christian; Sperber, Peter

2010-10-01

Magnetorheological finishing is a typical commercial application of a computer-controlled polishing process in the manufacturing of precision optical surfaces. Precise knowledge of the material removal characteristic of the polishing tool (influence function) is essential for controlling the material removal on the workpiece surface by the dwell time method. Results from the testing series with magnetorheological finishing have shown that a deviation of only 5% between the actual material removal characteristic of the polishing tool and that represented by the influence function caused a considerable reduction in the polishing quality. The paper discusses reasons for inaccuracies in the influence function and the effects on the polishing quality. The generic results of this research serve for the development of improved polishing strategies, and may be used in alternative applications of computer-controlled polishing processes that quantify the material removal characteristic by influence functions.

National Machine Guarding Program: Part 1. Machine safeguarding practices in small metal fabrication businesses.

PubMed

Parker, David L; Yamin, Samuel C; Brosseau, Lisa M; Xi, Min; Gordon, Robert; Most, Ivan G; Stanley, Rodney

2015-11-01

Metal fabrication workers experience high rates of traumatic occupational injuries. Machine operators in particular face high risks, often stemming from the absence or improper use of machine safeguarding or the failure to implement lockout procedures. The National Machine Guarding Program (NMGP) was a translational research initiative implemented in conjunction with two workers' compensation insures. Insurance safety consultants trained in machine guarding used standardized checklists to conduct a baseline inspection of machine-related hazards in 221 business. Safeguards at the point of operation were missing or inadequate on 33% of machines. Safeguards for other mechanical hazards were missing on 28% of machines. Older machines were both widely used and less likely than newer machines to be properly guarded. Lockout/tagout procedures were posted at only 9% of machine workstations. The NMGP demonstrates a need for improvement in many aspects of machine safety and lockout in small metal fabrication businesses. © 2015 The Authors. American Journal of Industrial Medicine published by Wiley Periodicals, Inc.

Corrosion of RoHS-Compliant Surface Finishes in Corrosive Mixed Flowing Gas Environments

NASA Astrophysics Data System (ADS)

Hannigan, K.; Reid, M.; Collins, M. N.; Dalton, E.; Xu, C.; Wright, B.; Demirkan, K.; Opila, R. L.; Reents, W. D.; Franey, J. P.; Fleming, D. A.; Punch, J.

2012-03-01

Recently, the corrosion resistance of printed wiring board (PWB) finishes has generated considerable interest due to field failures observed in various parts of the world. This study investigates the corrosion issues associated with the different lead-free PWB surface finishes. Corrosion products on various PWB surface finishes generated in mixed flowing gas (MFG) environments were studied, and analysis techniques such as scanning electron microscopy, energy-dispersive x-ray, x-ray diffraction, focused ion beam, and scanning Auger microscopy were used to quantify the corrosion layer thickness and determine the composition of corrosion products. The corrosion on organic solderability preservative samples shows similar corrosion products to bare copper and is mainly due to direct attack of copper traces by corrosive gases. The corrosion on electroless nickel immersion gold occurs primarily through the porosity in the film and is accelerated by the galvanic potential between gold and copper; similar results were observed on immersion silver. Immersion tin shows excellent corrosion resistance due to its inherent corrosion resistance in the MFG environment as well as the opposite galvanic potential between tin and copper compared with gold or silver and copper.

40 CFR 410.60 - Applicability; description of the carpet finishing subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Applicability; description of the carpet finishing subcategory. 410.60 Section 410.60 Protection of Environment ENVIRONMENTAL PROTECTION..., carbonizing, fulling, dyeing, printing, resin treatment, waterproofing, flameproofing, soil repellency...

Usefulness of food chain information provided by Dutch finishing pig producers to control antibiotic residues in pork.

PubMed

van Wagenberg, Coen P A; Backus, Gé B C; van der Vorst, Jack G A J; Urlings, Bert A P

2012-11-01

The EU prescribes that food business operators must use food chain information to assist in food safety control. This study analyses usefulness of food chain information about antibiotic usage covering the 60-day period prior to delivery of pigs to slaughter in the control of antibiotic residues in pork. A dataset with 479 test results for antibiotic residues in tissue samples of finishing pigs delivered to a Dutch slaughter company was linked to information provided by pig producers about antibiotic usage in these finishing pigs. Results show that twice as many producers reported using antibiotics in the group of 82 producers with antibiotic residues (11.0%) compared to the group without antibiotic residues (5.5%) (p=0.0686). For 89% of consignments with a finishing pig with antibiotic residues, the producer reported 'did not use antibiotics'. Food chain information about antibiotic usage provided by Dutch pig producers was no guarantee for absence of antibiotic residues in delivered finishing pigs. Copyright © 2012 Elsevier B.V. All rights reserved.

Study of austenitic stainless steel welded with low alloy steel filler metal. [tensile and impact strength tests

NASA Technical Reports Server (NTRS)

Burns, F. A.; Dyke, R. A., Jr.

1979-01-01

The tensile and impact strength properties of 316L stainless steel plate welded with low alloy steel filler metal were determined. Tests were conducted at room temperature and -100 F on standard test specimens machined from as-welded panels of various chemical compositions. No significant differences were found as the result of variations in percentage chemical composition on the impact and tensile test results. The weldments containing lower chromium and nickel as the result of dilution of parent metal from the use of the low alloy steel filler metal corroded more severely in a marine environment. The use of a protective finish, i.e., a nitrile-based paint containing aluminum powder, prevented the corrosive attack.

The effects of finishing diet and postmortem ageing on the eating quality of the M. longissimus thoracis of electrically stimulated Brahman steer carcasses.

PubMed

Bruce, H L; Stark, J L; Beilken, S L

2004-06-01

Beef from cattle finished on grass will be of similar quality to that from cattle finished on grain when their carcasses are processed using best practice protocols. To test this hypothesis, carcasses of twenty Brahman steers, finished to 400 kg live weight on either Buffel grass pasture (n=10) or grain (n=10), were electrically stimulated with 400 V for 50 s 45 min postmortem, and their beef quality assessed 1 and 14 days postmortem. Hot weight, rump subcutaneous fat thickness and animal rate of growth in the 205 days preceding slaughter were recorded for each carcass as potential influences on beef quality. Quality of the M. longissimus thoracis (LT) at 1 and 14 days postmortem was evaluated using peak Warner-Bratzler shear force, compression, pH, cooking loss and taste panel acceptability, as well as by moisture and crude fat contents measured at 1 day postmortem. Results showed that steers finished on pasture grew the slowest and had the least subcutaneous fat at the same carcass weight. LT from carcasses of steers finished on pasture also had the shortest mean sarcomere lengths, suggesting these muscles may have been cold-affected, but there was no effect of diet on peak shear force. LT from carcasses of steers finished on pasture had the highest mean compression value, possibly because of increased collagen cross-linking associated with slow growth or increased exercise. Ageing significantly decreased LT peak shear force and compression values and increased cooking loss, L (∗), a (∗) and b (∗) values. Taste panellists rated the aged, grass-finished beef the most tender and the best quality; however, the taste panel in this study may have favoured LT from grass-finished steers because it was significantly juicier than LT from the grain-finished steer carcasses. These results indicated that carcass composition and processing conditions interact to exert a greater effect on LT toughness and sensory acceptability than finishing diet. Ageing LT from steers

Introduction to Concrete Finishing. Instructor Edition. Introduction to Construction Series.

ERIC Educational Resources Information Center

Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This instructor's guide contains the materials required to teach a competency-based introductory course in concrete finishing to students who have chosen to explore careers in construction. The following topics are covered in the course's three instructional units: concrete materials, concrete tools, and applied skills. Each unit contains some or…

Selenium and metal concentrations in waterbird eggs and chicks at Agassiz National Wildlife Refuge, Minnesota

USGS Publications Warehouse

Custer, T.W.; Custer, Christine M.; Eichhorst, B.A.; Warburton, D.

2007-01-01

Exceptionally high cadmium (Cd) and chromium (Cr) concentrations were reported in eggs, feathers, or livers of selected waterbird species nesting at Agassiz National Wildlife Refuge (Agassiz) in 1994. Ten- to 15-day-old Franklin's gull (Larus pipixcan), black-crowned night-heron (Nycticorax nycticorax), and eared grebe (Podiceps nigricollis) chicks were collected in 1998, 1999, and 2001 at Agassiz and analyzed for selenium (Se) and metals including Cd and Cr. Freshly laid eggs were collected in 2001 from Franklin's gull, black-crowned night-heron, eared grebe, and pied-billed grebe (Podilymbus podiceps) nests at Agassiz. Based on a multivariate analysis, the pattern of Se and metal concentrations differed among species for eggs, chick feathers, and chick livers. Low Cd and Cr concentrations were measured in eggs, chick livers, and chick feathers of all four species. Mercury concentrations in black-crowned night-heron and eared grebe eggs collected from Agassiz in 2001 were lower than concentrations reported in 1994. Se and metal concentrations, including Cd and Cr, in waterbird eggs and chicks collected at Agassiz in 1998, 1999, and 2001 were not at toxic levels. ?? 2007 Springer Science+Business Media, LLC.

21 CFR 212.70 - What controls and acceptance criteria must I have for my finished PET drug products?

Code of Federal Regulations, 2010 CFR

2010-04-01

... for my finished PET drug products? 212.70 Section 212.70 Food and Drugs FOOD AND DRUG ADMINISTRATION... What controls and acceptance criteria must I have for my finished PET drug products? (a) Specifications. You must establish specifications for each PET drug product, including criteria for determining...

Pressurized Shell Molds For Metal-Matrix Composites

NASA Technical Reports Server (NTRS)

Kashalikar, Uday K.; Lusignea, Richard N.; Cornie, James

1993-01-01

Balanced-pressure molds used to make parts in complex shapes from fiber-reinforced metal-matrix composite materials. In single step, molding process makes parts in nearly final shapes; only minor finishing needed. Because molding pressure same on inside and outside, mold does not have to be especially strong and can be made of cheap, nonstructural material like glass or graphite. Fibers do not have to be cut to conform to molds. Method produces parts with high content of continuous fibers. Parts stiff but light in weight, and coefficients of thermal expansion adjusted. Parts resistant to mechanical and thermal fatigue superior to similar parts made by prior fabrication methods.

Development and validation of an rDNA operon based primer walking strategy applicable to de novo bacterial genome finishing

PubMed Central

Eastman, Alexander W.; Yuan, Ze-Chun

2015-01-01

Advances in sequencing technology have drastically increased the depth and feasibility of bacterial genome sequencing. However, little information is available that details the specific techniques and procedures employed during genome sequencing despite the large numbers of published genomes. Shotgun approaches employed by second-generation sequencing platforms has necessitated the development of robust bioinformatics tools for in silico assembly, and complete assembly is limited by the presence of repetitive DNA sequences and multi-copy operons. Typically, re-sequencing with multiple platforms and laborious, targeted Sanger sequencing are employed to finish a draft bacterial genome. Here we describe a novel strategy based on the identification and targeted sequencing of repetitive rDNA operons to expedite bacterial genome assembly and finishing. Our strategy was validated by finishing the genome of Paenibacillus polymyxa strain CR1, a bacterium with potential in sustainable agriculture and bio-based processes. An analysis of the 38 contigs contained in the P. polymyxa strain CR1 draft genome revealed 12 repetitive rDNA operons with varied intragenic and flanking regions of variable length, unanimously located at contig boundaries and within contig gaps. These highly similar but not identical rDNA operons were experimentally verified and sequenced simultaneously with multiple, specially designed primer sets. This approach also identified and corrected significant sequence rearrangement generated during the initial in silico assembly of sequencing reads. Our approach reduces the required effort associated with blind primer walking for contig assembly, increasing both the speed and feasibility of genome finishing. Our study further reinforces the notion that repetitive DNA elements are major limiting factors for genome finishing. Moreover, we provided a step-by-step workflow for genome finishing, which may guide future bacterial genome finishing projects. PMID

Understanding and reduction of defects on finished EUV masks

NASA Astrophysics Data System (ADS)

Liang, Ted; Sanchez, Peter; Zhang, Guojing; Shu, Emily; Nagpal, Rajesh; Stivers, Alan

2005-05-01

To reduce the risk of EUV lithography adaptation for the 32nm technology node in 2009, Intel has operated a EUV mask Pilot Line since early 2004. The Pilot Line integrates all the necessary process modules including common tool sets shared with current photomask production as well as EUV specific tools. This integrated endeavor ensures a comprehensive understanding of any issues, and development of solutions for the eventual fabrication of defect-free EUV masks. Two enabling modules for "defect-free" masks are pattern inspection and repair, which have been integrated into the Pilot Line. This is the first time we are able to look at real defects originated from multilayer blanks and patterning process on finished masks over entire mask area. In this paper, we describe our efforts in the qualification of DUV pattern inspection and electron beam mask repair tools for Pilot Line operation, including inspection tool sensitivity, defect classification and characterization, and defect repair. We will discuss the origins of each of the five classes of defects as seen by DUV pattern inspection tool on finished masks, and present solutions of eliminating and mitigating them.

Surface finish of resin-modified and highly viscous glass ionomer cements produced by new one-step systems.

PubMed

Yap, Adrian U J; Ng, J J; Yap, S H; Teo, C K

2004-01-01

This study investigated the surface finish of resin-modified (Fuji II LC, GC) and highly viscous (Fuji IX GP Fast, GC) glass ionomer cements after treatment with three one-step finishing/polishing systems (One-Gloss [OG], Shofu; Pogo [PG], Dentsply; Sof-Lex Brush [SB], 3M-ESPE). The surface roughness obtained was compared to that using a matrix strip [MS], a two-step rubber abrasive (CompoSite [CS], Shofu) and a graded abrasive disk (Super Snap [SS], Shofu) system. Eight specimens (3-mm long x 3-mm wide x 2-mm deep) of each material were made for the various treatment groups. With the exception of the MS group, all groups were roughened with 320 grit grinding paper using a lapping device prior to finishing/polishing with the different systems. The mean surface roughness (microm) was measured with a profilometer. Data was subjected to ANOVA/Scheffe's tests at significance level 0.05. Mean Ra ranged from 0.13 to 1.04 microm for Fuji II LC and 0.14 to 0.81 for Fuji IX GP. For both materials, the smoothest surface was obtained with MS and the roughest with OG. Depending on the materials, the surface finish produced by PG and SB was superior or comparable to that obtained with CS and SS. The effectiveness of one-step systems, when used to finish/polish resin-modified and highly viscous glass ionomer cements, is product dependent.

SURFACE FINISHES ON STAINLESS STEEL REDUCE BACTERIAL ATTACHMENT AND EARLY BIOFILM FORMATION: SCANNING ELECTRON AND ATOMIC FORCE MICROSCOPY STUDY

EPA Science Inventory

Three common finishing treatments of stainless steel that are used for equipment during poultry processing were tested for resistance to bacterial contamination. Methods were developed to measure attached bacteria and to identify factors that make surface finishes susceptible or ...

21 CFR 212.70 - What controls and acceptance criteria must I have for my finished PET drug products?

Code of Federal Regulations, 2011 CFR

2011-04-01

... for my finished PET drug products? 212.70 Section 212.70 Food and Drugs FOOD AND DRUG ADMINISTRATION... acceptance criteria must I have for my finished PET drug products? (a) Specifications. You must establish specifications for each PET drug product, including criteria for determining identity, strength, quality, purity...

21 CFR 212.70 - What controls and acceptance criteria must I have for my finished PET drug products?

Code of Federal Regulations, 2013 CFR

2013-04-01

... for my finished PET drug products? 212.70 Section 212.70 Food and Drugs FOOD AND DRUG ADMINISTRATION... acceptance criteria must I have for my finished PET drug products? (a) Specifications. You must establish specifications for each PET drug product, including criteria for determining identity, strength, quality, purity...

21 CFR 212.70 - What controls and acceptance criteria must I have for my finished PET drug products?

Code of Federal Regulations, 2014 CFR

2014-04-01

... for my finished PET drug products? 212.70 Section 212.70 Food and Drugs FOOD AND DRUG ADMINISTRATION... acceptance criteria must I have for my finished PET drug products? (a) Specifications. You must establish specifications for each PET drug product, including criteria for determining identity, strength, quality, purity...

21 CFR 212.70 - What controls and acceptance criteria must I have for my finished PET drug products?

Code of Federal Regulations, 2012 CFR

2012-04-01

... for my finished PET drug products? 212.70 Section 212.70 Food and Drugs FOOD AND DRUG ADMINISTRATION... acceptance criteria must I have for my finished PET drug products? (a) Specifications. You must establish specifications for each PET drug product, including criteria for determining identity, strength, quality, purity...

Rheological properties of magnetorheological fluid and its finishing application on large aperture BK7 glass

NASA Astrophysics Data System (ADS)

Wang, C.; Wei, Q. L.; Huang, W.; Luo, Q.; He, J. G.; Tang, G. P.

2013-07-01

The CeO2 nanoparticles with modified surface and mean sizes distribution during 107.0 nm - 127.7 nm are used as abrasive in magnetorheological finishing (MRF) fluid. The slow rotation dispersion without shearing thinning is better than fast emulsification dispersion. Steady D-shaped finishing spots and high quality precise processing surface with PV=0.1λ, GRMS=0.002λ/cm, Rq=0.83 nm are obtained on a 435 mm x 435 mm BK7 glass under self-developed MRF apparatus.

Outcomes following revision surgery performed for adverse reactions to metal debris in non-metal-on-metal hip arthroplasty patients: Analysis of 185 revisions from the National Joint Registry for England and Wales.

PubMed

Matharu, G S; Judge, A; Murray, D W; Pandit, H G

2017-07-01

Few studies have assessed outcomes following non-metal-on-metal hip arthroplasty (non-MoMHA) revision surgery performed for adverse reactions to metal debris (ARMD). We assessed outcomes following non-MoMHA revision surgery performed for ARMD, and identified predictors of re-revision. We performed a retrospective observational study using data from the National Joint Registry for England and Wales. All non-MoMHAs undergoing revision surgery for ARMD between 2008 and 2014 were included (185 hips in 185 patients). Outcome measures following ARMD revision were intra-operative complications, mortality and re-revision surgery. Predictors of re-revision were identified using Cox regression. Intra-operative complications occurred in 6.0% (n = 11) of the 185 cases. The cumulative four-year patient survival rate was 98.2% (95% CI 92.9 to 99.5). Re-revision surgery was performed in 13.5% (n = 25) of hips at a mean time of 1.2 years (0.1 to 3.1 years) following ARMD revision. Infection (32%; n = 8), dislocation/subluxation (24%; n = 6), and aseptic loosening (24%; n = 6) were the most common re-revision indications. The cumulative four-year implant survival rate was 83.8% (95% CI 76.7 to 88.9). Multivariable analysis identified three predictors of re-revision: multiple revision indications (hazard ratio (HR) = 2.78; 95% CI 1.03 to 7.49; p = 0.043); selective component revisions (HR = 5.76; 95% CI 1.28 to 25.9; p = 0.022); and ceramic-on-polyethylene revision bearings (HR = 3.08; 95% CI 1.01 to 9.36; p = 0.047). Non-MoMHAs revised for ARMD have a high short-term risk of re-revision, with important predictors of future re-revision including selective component revision, multiple revision indications, and ceramic-on-polyethylene revision bearings. Our findings may help counsel patients about the risks of ARMD revision, and guide reconstructive decisions. Future studies attempting to validate the predictors identified should also assess the effects of implant design (metallurgy

Fundamental studies of tin whiskering in microelectronics finishes

NASA Astrophysics Data System (ADS)

Pinol, Lesly Agnes

Common electronics materials, such as tin, copper, steel, and brass, are ambient reactive under common use conditions, and as such are prone to corrosion. During the early 1940s, reports of failures due to electrical shorting of components caused by 'whisker' (i.e., filamentary surface protrusion) growth on many surface types---including the aforementioned metals---began to emerge. Lead alloying of tin (3--10% by weight, typically in the eutectic proportion) eliminated whiskering risk for decades, until the July 2006 adoption of the Restriction of Hazardous Substances (RoHS) directive was issued by the European Union. This directive, which has since been adopted by California and parts of China, severely restricted the use of lead (<1000 ppm) in all electrical and electronics equipment being placed on the EU market, imposing the need for developing reliable new "lead-free" alternatives to SnPb. In spite of the abundance of modern-day anecdotes chronicling whisker-related failures in satellites, nuclear power stations, missiles, pacemakers, and spacecraft navigation equipment, pure tin finishes are still increasingly being employed today, and the root cause(s) of tin whiskering remains elusive. This work describes a series of structured experiments exploring the fundamental relationships between the incidence of tin whiskering (as dependent variable) and numerous independent variables. These variables included deposition method (electroplating, electroless plating, template-based electrochemical synthesis, and various physical vapor deposition techniques, including resistive evaporation, electron beam evaporation, and sputtering), the inclusion of microparticles and organic contamination, the effects of sample geometry, and nanostructuring. Key findings pertain to correlations between sample geometry and whisker propensity, and also to the stress evolution across a series of 4"-diameter silicon wafers of varying thicknesses with respect to the degree of post-metallization

Investigation of rapidly solidified aluminum by using diamond turning and a magnetorheological finishing process

NASA Astrophysics Data System (ADS)

Cheng, Yuan-Chieh; Hsu, Wei-Yao; Kuo, Ching-Hsiang; Abou-El-Hossein, Khaled; Otieno, Timothy

2015-08-01

The metal mirror has been widely used in optical application for a longtime. Especially the aluminum 6061 is often considered the preferred material for manufacturing optical components for ground-based astronomical applications. One reason for using this material is its high specific stiffness and excellent thermal properties. However, a large amount of data exists for this material and commercially available aluminum 6061 using single point diamond turning (SPDT) and polishing process can achieve surface roughness values of approximately 2 to 4 nm, which is adequate for applications that involve the infrared spectral range, but not for the shorter spectral range. A novel aluminum material, fabricated using a rapid solidification process that is equivalent to the conventional aluminum 6061 alloy grade has been used in optical applications in recent years because of its smaller grain size. In this study, the surface quality of the rapid solidification aluminum after single point diamond turning and followed by magnetorheological finish (MRF) process is investigated and compared with conventional aluminum 6061. Both the surface roughness Ra was evaluated using white light interferometers. Finally, indicators such as optimal fabrication parameter combination and optical performance are discussed.

Effect of temperature and O-ring gland finish on sealing ability of Viton V747-75

NASA Technical Reports Server (NTRS)

Lach, Cynthia L.

1993-01-01

As a part of the redesign project of the Space Shuttle solid rocket motor (SRM) following the Challenger accident, the field joint was redesigned to minimize the relative joint motion caused by internal motor pressurization during ignition. The O-ring seals and glands for the field joint were designed both to accommodate structural deflections and to promote pressure-assisted sealing. Tests were conducted in various face seal fixtures to evaluate the ability of Viton V747-75 O-rings to seal for a range of temperatures and surface finishes of the redesigned O-ring gland. The effect of surface finish on the sealing performance and wear characteristics of the O-rings was evaluated during simulated launch conditions that included low-frequency vibrations, gap openings, and rapid pressurizations. The effect of contamination on the sealing performance was also investigated. The O-rings sealed throughout the 75 deg F leak check test and for the seal tests from 50 deg F to 120 deg F for the range of surface finishes investigated. Although abrasions were found in the O-rings from pressurization against the rougher finishes, these abrasions were not detrimental to sealing. Below 50 deg F, Viton V747-75 O-rings were insufficiently resilient to track the test gap opening.

Impact of test sensitivity and specificity on pig producer incentives to control Mycobacterium avium infections in finishing pigs.

PubMed

van Wagenberg, Coen P A; Backus, Gé B C; Wisselink, Henk J; van der Vorst, Jack G A J; Urlings, Bert A P

2013-09-01

In this paper we analyze the impact of the sensitivity and specificity of a Mycobacterium avium (Ma) test on pig producer incentives to control Ma in finishing pigs. A possible Ma control system which includes a serodiagnostic test and a penalty on finishing pigs in herds detected with Ma infection was modelled. Using a dynamic optimization model and a grid search of deliveries of herds from pig producers to slaughterhouse, optimal control measures for pig producers and optimal penalty values for deliveries with increased Ma risk were identified for different sensitivity and specificity values. Results showed that higher sensitivity and lower specificity induced use of more intense control measures and resulted in higher pig producer costs and lower Ma seroprevalence. The minimal penalty value needed to comply with a threshold for Ma seroprevalence in finishing pigs at slaughter was lower at higher sensitivity and lower specificity. With imperfect specificity a larger sample size decreased pig producer incentives to control Ma seroprevalence, because the higher number of false positives resulted in an increased probability of rejecting a batch of finishing pigs irrespective of whether the pig producer applied control measures. We conclude that test sensitivity and specificity must be considered in incentive system design to induce pig producers to control Ma in finishing pigs with minimum negative effects. Copyright © 2013 Elsevier B.V. All rights reserved.

Endocannabinoid concentrations in plasma during the finishing period are associated with feed efficiency and carcass composition of beef cattle

USDA-ARS?s Scientific Manuscript database

We previously have shown that plasma concentrations of endocannabinoids (EC) are positively correlated with feed efficiency and leaner carcasses in finishing steers. However, whether the animal growth during the finishing period affects the concentration of EC is unknown. The objective of this study...

Automated edge finishing using an active XY table

DOEpatents

Loucks, Clifford S.; Starr, Gregory P.

1993-01-01

The disclosure is directed to an apparatus and method for automated edge finishing using hybrid position/force control of an XY table. The disclosure is particularly directed to learning the trajectory of the edge of a workpiece by "guarded moves". Machining is done by controllably moving the XY table, with the workpiece mounted thereon, along the learned trajectory with feedback from a force sensor. Other similar workpieces can be mounted, without a fixture on the XY table, located and the learned trajectory adjusted

Comparison of U.S. Environmental Protection Agency and U.S. Composting Council microbial detection methods in finished compost and regrowth potential of Salmonella spp. and Escherichia coli O157:H7 in finished compost.

PubMed

Reynnells, Russell; Ingram, David T; Roberts, Cheryl; Stonebraker, Richard; Handy, Eric T; Felton, Gary; Vinyard, Bryan T; Millner, Patricia D; Sharma, Manan

2014-07-01

Bacterial pathogens may survive and regrow in finished compost due to incomplete thermal inactivation during or recontamination after composting. Twenty-nine finished composts were obtained from 19 U.S. states and were separated into three broad feedstock categories: biosolids (n=10), manure (n=4), and yard waste (n=15). Three replicates of each compost were inoculated with ≈ 1-2 log CFU/g of nonpathogenic Escherichia coli, Salmonella spp., and E. coli O157:H7. The U.S. Environmental Protection Agency's (EPA) protocols and U.S. Composting Council's (USCC) Test Methods for the Examination of Composting and Compost (TMECC) were compared to determine which method recovered higher percentages of inoculated E. coli (representing fecal coliforms) and Salmonella spp. from 400-g samples of finished composts. Populations of Salmonella spp. and E. coli O157:H7 were determined over 3 days while stored at 25°C and compared to physicochemical parameters to predict their respective regrowth potentials. EPA Method 1680 recovered significantly (p=0.0003) more inoculated E. coli (68.7%) than TMECC 07.01 (48.1%) due to the EPA method using more compost in the initial homogenate, larger transfer dilutions, and a larger most probable number scheme compared to TMECC 07.01. The recoveries of inoculated Salmonella spp. by Environmental Protection Agency Method 1682 (89.1%) and TMECC 07.02 (72.4%) were not statistically significant (p=0.44). The statistically similar recovery percentages may be explained by the use of a nonselective pre-enrichment step used in both methods. No physicochemical parameter (C:N, moisture content, total organic carbon) was able to serve as a sole predictor of regrowth of Salmonella spp. or E. coli O157:H7 in finished compost. However, statistical analysis revealed that the C:N ratio, total organic carbon, and moisture content all contributed to pathogen regrowth potential in finished composts. It is recommended that the USCC modify TMECC protocols to test

Cement Finishing. Pre-Apprenticeship Phase 2 Training. Student Training Modules.

ERIC Educational Resources Information Center

Nama, Joe

These 20 Student Training Modules on cement finishing comprise one of nine sets of self-paced learning modules developed for Pre-Apprenticeship Phase 2 Training. (A companion instructor's guide is available separately as CE 031 575.) The modules are designed to impart trade knowledge and skills to the student. Each module contains some or all of…

Cleaning Process Development for Metallic Additively Manufactured Parts

NASA Technical Reports Server (NTRS)

Tramel, Terri L.; Welker, Roger; Lowery, Niki; Mitchell, Mark

2014-01-01

Additive Manufacturing of metallic components for aerospace applications offers many advantages over traditional manufacturing techniques. As a new technology, many aspects of its widespread utilization remain open to investigation. Among these are the cleaning processes that can be used for post finishing of parts and measurements to verify effectiveness of the cleaning processes. Many cleaning and drying processes and measurement methods that have been used for parts manufactured using conventional techniques are candidates that may be considered for cleaning and verification of additively manufactured parts. Among these are vapor degreasing, ultrasonic immersion and spray cleaning, followed by hot air drying, vacuum baking and solvent displacement drying. Differences in porosity, density, and surface finish of additively manufactured versus conventionally manufactured parts may introduce new considerations in the selection of cleaning and drying processes or the method used to verify their effectiveness. This presentation will review the relative strengths and weaknesses of different candidate cleaning and drying processes as they may apply to additively manufactured metal parts for aerospace applications. An ultrasonic cleaning technique for exploring the cleanability of parts will be presented along with an example using additively manufactured Inconel 718 test specimens to illustrate its use. The data analysis shows that this ultrasonic cleaning approach results in a well-behaved ultrasonic cleaning/extraction behavior. That is, it does not show signs of accelerated cavitation erosion of the base material, which was later confirmed by neutron imaging. In addition, the analysis indicated that complete cleaning would be achieved by ultrasonic immersion cleaning at approximately 5 minutes, which was verified by subsequent cleaning of additional parts.

Feed efficiency differences and reranking in beef steers fed grower and finisher diets.

PubMed

Durunna, O N; Mujibi, F D N; Goonewardene, L; Okine, E K; Basarab, J A; Wang, Z; Moore, S S

2011-01-01

This 3-yr study used 490 steers to determine whether feedlot steers changed their feed efficiency (FE) ranking when fed a grower diet, then a finisher diet. The steers were crossbreds and were between 5 to 7 mo of age. There were 2 feeding periods each year. Within each year, approximately 90 steers had their diet switched from a grower to a finisher diet (feed-swap group), whereas another 90 steers were fed either the grower (grower-fed group) or the finisher (finisher-fed group) diet throughout the feeding trial. Each feeding test lasted for a minimum of 10 wk, and all steers were fed ad libitum. Individual animal feed intakes were collected using the GrowSafe feeding system, and BW were measured every 2 wk. Residual feed intake (RFI), G:F, and Kleiber ratio (KR) were computed at the end of each feeding period. For each measure of efficiency, animals were classified as low, medium, or high based on 0.5 SD from the mean. The majority of steers did not maintain the previous efficiency class in the second period. Approximately 58, 51, and 51% of steers in the feed-swap group, finisher-fed group, and the grower-fed group, respectively, changed their RFI measure by 0.5 SD. A low rank correlation occurred in all test groups but was less in the feed-swap group. Spearman rank correlations between the 2 feeding periods in the feed-swap group were 0.33, 0.20, and 0.31 for RFI, G:F, and KR, respectively. Classifications based on G:F and KR showed that a greater number of steers (P < 0.05) in the feed-swap group did not maintain their FE class from 1 feeding regimen to the other, whereas classification based on RFI did not show any difference (P > 0.05) between the proportions of individuals that changed or maintained their FE class. In the groups without a feed-swap, there was no difference (P > 0.05) in the proportion of steers that changed or maintained the same FE class for all FE measures. Our results suggest that diet type and feeding period affect the FE ranking in

[Comparative analysis of 3D data visibility of the prepared tooth finishing line on a synthetic jaw model, captured by international scanners in a laboratory conditions].

PubMed

Ryakhovskiy, A N; Kostyukova, V V

The aim of the study was to compare accuracy of digital impression's finishing line and the zone under it taken by different intraoral scanning systems. Parameters of comparison were: different level of the finishing line to the gingiva and width of sulcus after retraction. For this purpose two synthetic jaw models with prepared teeth were scanned using intraoral scanning systems: 3D Progress (MHT S.P.A., IT - MHT Optic Research AG, CH); True Definition (3M ESPE, USA); Trios (3Shape A/S, DNK); CEREC AC Bluecam, CEREC Omnicam (Sirona Dental System GmbH, DE); Planscan (Planmeca, FIN) (each n=10). Reference-scanning was done by ATOS Core (GOM mbH, DE). The resulting digital impressions were superimposed with the master-scan. The lowest measured deviations (trueness) for intraoral scanners, where the finishing line was 0.5 mm above gingiva were with scanner True Definition - 18.8±6.63 (on the finishing line) and 51.0±14.33 µm (0.3 mm under the finishing line). In conditions where finishing line was on the same level with gingiva, scanner Trios showed the best results: 17.0±3.96 and 52.7±6.52 µm. When the finishing line was 0.5 mm under gingiva, none of the testing scanners could visualize the zone 0.3 mm lower the finishing line. The best results for accuracy o the finishing line in that circumstances showed Trios: 15.1±5.05 µm. The optimum visualization of the finishing line and the zone under it was reached when the sulcus was 0.3 mm after retraction. Thus, the best accuracy was obtained with Trios: 10.3±2.69 (on the finishing line) and 57.2±13.58 µm (0.3 mm under finishing line). The results show that intraoral scanners also provide enough accuracy for indicating finishing line and the zone under it in different conditions of preparation and gingiva retraction. However, not all of the testing scanners can properly indicate finishing line and the zone under it when shoulder is below gingiva and the width of sulcus is less than 0.2 mm.

Finishing and Special Motifs: Lessons Learned from CRISPR Analysis Using Next-Generation Draft Sequences (7th Annual SFAF Meeting, 2012)

ScienceCinema

Campbell, Catherine

2018-01-22

Catherine Campbell on "Finishing and Special Motifs: Lessons learned from CRISPR analysis using next-generation draft sequences" at the 2012 Sequencing, Finishing, Analysis in the Future Meeting held June 5-7, 2012 in Santa Fe, New Mexico.

Finishing and Special Motifs: Lessons Learned from CRISPR Analysis Using Next-Generation Draft Sequences (7th Annual SFAF Meeting, 2012)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Campbell, Catherine

Catherine Campbell on "Finishing and Special Motifs: Lessons learned from CRISPR analysis using next-generation draft sequences" at the 2012 Sequencing, Finishing, Analysis in the Future Meeting held June 5-7, 2012 in Santa Fe, New Mexico.

Plutonium Finishing Plant (PFP) Final Safety Analysis Report (FSAR) [SEC 1 THRU 11

DOE Office of Scientific and Technical Information (OSTI.GOV)

ULLAH, M K

2001-02-26

The Plutonium Finishing Plant (PFP) is located on the US Department of Energy (DOE) Hanford Site in south central Washington State. The DOE Richland Operations (DOE-RL) Project Hanford Management Contract (PHMC) is with Fluor Hanford Inc. (FH). Westinghouse Safety Management Systems (WSMS) provides management support to the PFP facility. Since 1991, the mission of the PFP has changed from plutonium material processing to preparation for decontamination and decommissioning (D and D). The PFP is in transition between its previous mission and the proposed D and D mission. The objective of the transition is to place the facility into a stablemore » state for long-term storage of plutonium materials before final disposition of the facility. Accordingly, this update of the Final Safety Analysis Report (FSAR) reflects the current status of the buildings, equipment, and operations during this transition. The primary product of the PFP was plutonium metal in the form of 2.2-kg, cylindrical ingots called buttoms. Plutonium nitrate was one of several chemical compounds containing plutonium that were produced as an intermediate processing product. Plutonium recovery was performed at the Plutonium Reclamation Facility (PRF) and plutonium conversion (from a nitrate form to a metal form) was performed at the Remote Mechanical C (RMC) Line as the primary processes. Plutonium oxide was also produced at the Remote Mechanical A (RMA) Line. Plutonium processed at the PFP contained both weapons-grade and fuels-grade plutonium materials. The capability existed to process both weapons-grade and fuels-grade material through the PRF and only weapons-grade material through the RMC Line although fuels-grade material was processed through the line before 1984. Amounts of these materials exist in storage throughout the facility in various residual forms left from previous years of operations.« less

Control of formaldehyde and TVOC emission from wood-based flooring composites at various manufacturing processes by surface finishing.

PubMed

Kim, Sumin

2010-04-15

This paper assesses the reproducibility of testing formaldehyde and TVOC emission behavior from wood flooring composites bonded by urea-formaldehyde resin at various manufacturing steps for surface finishing materials. The surface adhesion step of laminate flooring for this research was divided into two steps; HDF only and HDF with LPMs. In the case of engineered flooring, the manufacturing steps were divided into three steps; plywood only, fancy veneer bonded on plywood and UV coated on fancy veneer with plywood. Formaldehyde and VOCs emission decreased at the process of final surface finishing materials; LPMs were applied on the surface of HDF for laminate flooring. Although emissions increased when fancy veneer was bonded onto plywood in the case of engineered flooring, emission was dramatically reduced up to similar level with plywood only when final surface finishing; UV-curable coating was applied on fancy veneer. This study suggests that formaldehyde and VOCs emission from floorings can be controlled at manufacturing steps for surface finishing. 2009 Elsevier B.V. All rights reserved.

Carcass parameters and meat quality in meat-goat kids finished on chicory, birdsfoot trefoil, or red clover pastures.

PubMed

Turner, K E; Cassida, K A; Zerby, H N; Brown, M A

2015-07-01

This study was conducted during the 2009 and 2010 grazing seasons to assess carcass parameters and chevon (goat meat) quality when meat-goat kids (n=72) were finished on pastures of red clover (Trifolium pratense L.; RCL), birdsfoot trefoil (Lotus corniculatus L.; BFT), or chicory (Cichorium intybus L.; CHIC). Final live weight (P<0.05) and carcass weight (P=0.10) were greater when goats were finished on RCL compared to CHIC with BFT being intermediate. Ribeye area, backfat thickness, body wall thickness, internal fat score, and leg score were not different (P>0.10) among treatments when adjusted for the covariate of carcass weight. Finishing meat-goat kids on RCL, BFT, or CHIC impacted concentrations of fatty acids (FAs) 18:1 trans-10, 18:1 cis-11, 18:2, 18:3 polyunsaturated fatty acids (PUFAs), omega-6, omega-3, and PUFA:saturated fatty acid ratio in longissimus lumborum samples. Finishing meat-goat kids on CHIC, RCL, or BFT pastures produced carcass weights acceptable for most ethnic markets in the USA. Published by Elsevier Ltd.

Assessment of heavy metals contamination in surface layers of Roztocze National Park forest soils (SE Poland) by indices of pollution.

PubMed

Mazurek, Ryszard; Kowalska, Joanna; Gąsiorek, Michał; Zadrożny, Paweł; Józefowska, Agnieszka; Zaleski, Tomasz; Kępka, Wojciech; Tymczuk, Maryla; Orłowska, Kalina

2017-02-01

In most cases, in soils exposed to heavy metals accumulation, the highest content of heavy metals was noted in the surface layers of the soil profile. Accumulation of heavy metals may occur both as a result of natural processes as well as anthropogenic activities. The quality of the soil exposed to heavy metal contamination can be evaluated by indices of pollution. On the basis of determined heavy metals (Pb, Zn, Cu, Mn, Ni and Cr) in the soils of Roztocze National Park the following indices of pollution were calculated: Enrichment Factor (EF), Geoaccumulation Index (I geo ), Nemerow Pollution Index (PI Nemerow ) and Potential Ecological Risk (RI). Additionally, we introduced and calculated the Biogeochemical Index (BGI), which supports determination of the ability of the organic horizon to accumulate heavy metals. A tens of times higher content of Pb, Zn, Cu and Mn was found in the surface layers compared to their content in the parent material. This distribution of heavy metals in the studied soils was related to the influence of anthropogenic pollution (both local and distant sources of emission), as well as soil properties such as pH, organic carbon and total nitrogen content. Copyright © 2016 Elsevier Ltd. All rights reserved.

Methods of analysis by the U.S. Geological Survey National Water Quality Laboratory; preparation procedure for aquatic biological material determined for trace metals

USGS Publications Warehouse

Hoffman, Gerald L.

1996-01-01

A method for the chemical preparation of tissue samples that are subsequently analyzed for 22 trace metals is described. The tissue-preparation procedure was tested with three National Institute of Standards and Technology biological standard reference materials and two National Water Quality Laboratory homogenized biological materials. A low-temperature (85 degrees Celsius) nitric acid digestion followed by the careful addition of hydrogen peroxide (30-percent solution) is used to decompose the biological material. The solutions are evaporated to incipient dryness, reconstituted with 5 percent nitric acid, and filtered. After filtration the solutions were diluted to a known volume and analyzed by inductively coupled plasma-mass spectrometry (ICP-MS), inductively coupled plasma-atomic emission spectrometry (ICP-AES), and cold vapor-atomic absorption spectrophotometry (CV-AAS). Many of the metals were determined by both ICP-MS and ICP-AES. This report does not provide a detailed description of the instrumental procedures and conditions used with the three types of instrumentation for the quantitation of trace metals determined in this study. Statistical data regarding recovery, accuracy, and precision for individual trace metals determined in the biological material tested are summarized.

Concentration data for anthropogenic organic compounds in ground water, surface water, and finished water of selected community water systems in the United States, 2002-05

USGS Publications Warehouse

Carter, Janet M.; Delzer, Gregory C.; Kingsbury, James A.; Hopple, Jessica A.

2007-01-01

The National Water-Quality Assessment Program of the U.S. Geological Survey began implementing Source Water-Quality Assessments (SWQAs) in 2001 that focus on characterizing the quality of source water and finished water of aquifers and major rivers used by some of the larger community water systems (CWSs) in the United States. As used for SWQA studies, source water is the raw (ambient) water collected at the supply well prior to water treatment (for ground water) or the raw (ambient) water collected from the river near the intake (for surface water), and finished water is the water that is treated and ready to be delivered to consumers. Finished water is collected before entering the distribution system. SWQA studies are conducted in two phases, and the objectives of SWQA studies are twofold: (1) to determine the occurrence and, for rivers, seasonal changes in concentrations of a broad list of anthropogenic organic compounds (AOCs) in aquifers and rivers that have some of the largest withdrawals for drinking-water supply (phase 1), and (2) for those AOCs found to occur most frequently in source water, characterize the extent to which these compounds are present in finished water (phase 2). These objectives were met for SWQA studies by collecting ground-water and surface-water (source) samples and analyzing these samples for 258 AOCs during phase 1. Samples from a subset of wells and surface-water sites located in areas with substantial agricultural production in the watershed were analyzed for 19 additional AOCs, for a total of 277 compounds analyzed for SWQA studies. The 277 compounds were classified according to the following 13 primary use or source groups: (1) disinfection by-products; (2) fumigant-related compounds; (3) fungicides; (4) gasoline hydrocarbons, oxygenates, and oxygenate degradates; (5) herbicides and herbicide degradates; (6) insecticides and insecticide degradates; (7) manufacturing additives; (8) organic synthesis compounds; (9) pavement- and

The effects of feeding increasing concentrations of corn oil on energy metabolism and nutrient balance in finishing beef steers

USDA-ARS?s Scientific Manuscript database

The use of added fat source is common in high-concentrate finishing diets. The objective of our experiment was to determine if feeding increasing concentrations of added dietary corn oil would decrease enteric methane production, increase the ME:DE ratio, and improve retained energy in finishing be...

The effects of feeding increasing concentrations of corn oil on energy metabolism and nutrient balance in finishing beef steers

USDA-ARS?s Scientific Manuscript database

The use of added fat source is common in high-concentrate finishing diets. The objective of our experiment was to determine if feeding increasing concentrations of added dietary corn oil would decrease enteric methane production, increase the ME:DE ratio, and improve recovered energy (RE) in finish...

Methyl tert-butyl ether (MTBE) in finished drinking water in Germany.

PubMed

Kolb, Axel; Püttmann, Wilhelm

2006-03-01

In the present study 83 finished drinking water samples from 50 cities in Germany were analyzed for methyl tert-butyl ether (MTBE) content with a detection limit of 10 ng/L. The detection frequency was 46% and the concentrations ranged between 17 and 712 ng/L. Highest concentrations were found in the community water systems (CWSs) of Leuna and Spergau in Saxony-Anhalt. These CWSs are supplied with water possibly affected by MTBE contaminated groundwater. MTBE was detected at concentrations lower than 100 ng/L in drinking water supplied by CWSs using bank filtered water from Rhine and Main Rivers. The results from Leuna and Spergau show that large groundwater contaminations in the vicinity of CWSs pose the highest risk for MTBE contamination in drinking water. CWSs using bank filtered water from Rhine and Main Rivers are susceptible to low MTBE contaminations in finished drinking water. All measured MTBE concentrations were below proposed limit values for drinking water.

Metal-Matrix/Hollow-Ceramic-Sphere Composites

NASA Technical Reports Server (NTRS)

Baker, Dean M.

2011-01-01

A family of metal/ceramic composite materials has been developed that are relatively inexpensive, lightweight alternatives to structural materials that are typified by beryllium, aluminum, and graphite/epoxy composites. These metal/ceramic composites were originally intended to replace beryllium (which is toxic and expensive) as a structural material for lightweight mirrors for aerospace applications. These materials also have potential utility in automotive and many other terrestrial applications in which there are requirements for lightweight materials that have high strengths and other tailorable properties as described below. The ceramic component of a material in this family consists of hollow ceramic spheres that have been formulated to be lightweight (0.5 g/cm3) and have high crush strength [40.80 ksi (.276.552 MPa)]. The hollow spheres are coated with a metal to enhance a specific performance . such as shielding against radiation (cosmic rays or x rays) or against electromagnetic interference at radio and lower frequencies, or a material to reduce the coefficient of thermal expansion (CTE) of the final composite material, and/or materials to mitigate any mismatch between the spheres and the matrix metal. Because of the high crush strength of the spheres, the initial composite workpiece can be forged or extruded into a high-strength part. The total time taken in processing from the raw ingredients to a finished part is typically 10 to 14 days depending on machining required.

Surface topographical effects on the structural growth of thick sputtered metal and alloy coatings

NASA Technical Reports Server (NTRS)

Spalvins, T.; Brainard, W. A.

1974-01-01

Thick sputtered S-Monel, silver, and 304 stainless steel coatings were deposited on mica and metal substrates with various surface finishes to investigate the structural growth of the coating by scanning electron microscopy. The geometry and the surface structure of the nodules are characterized. Compositional changes within the coating were analyzed by X-ray dispersion microscopy. Defects in the surface finish (i.e., scratches, inclusions, etc.) act as preferential nucleation sites and form isolated and complex nodules and various surface overgrowths in the coating. The nodule boundaries are very vulnerable to chemical etching and these nodules do not disappear after full annealing. Further, they have undesirable effects on mechanical properties; cracks are initiated at the nodules when the coating is stressed by mechanical forces. These effects are illustrated by micrographs. Nodular growth within a coating can be minimized or eliminated by reducing the surface roughness.

Slip casting and extruding shapes of rhenium with metal oxide additives. 1: Feasibility demonstration

NASA Technical Reports Server (NTRS)

Barr, F. A.; Page, R. J.

1986-01-01

The feasibility of fabricating small rhenium parts with metal oxide additives by means of slip casting and extrusion techniques is described. The metal oxides, ZrO2 and HfO2 were stabilized into the cubic phase with Y2O3. Additions of metal oxide to the rhenium of up to 15 weight percent were used. Tubes of 17 mm diameter with 0.5 mm walls were slip cast by adapting current ceramic oxide techniques. A complete cast double conical nozzle demonstrated the ability to meet shapes and tolerances. Extrusion of meter long tubing lengths of 3.9 mm o.d. x 2.3 mm i.d. final dimension is documented. Sintering schedules are presented to produce better than 95% of theoretical density parts. Finished machining was found possible were requried by electric discharge machining and diamond grinding.

Multi-Response Optimization of Resin Finishing by Using a Taguchi-Based Grey Relational Analysis

PubMed Central

Shafiq, Faizan; Sarwar, Zahid; Jilani, Muhammad Munib; Cai, Yingjie

2018-01-01

In this study, the influence and optimization of the factors of a non-formaldehyde resin finishing process on cotton fabric using a Taguchi-based grey relational analysis were experimentally investigated. An L27 orthogonal array was selected for five parameters and three levels by applying Taguchi’s design of experiments. The Taguchi technique was coupled with a grey relational analysis to obtain a grey relational grade for evaluating multiple responses, i.e., crease recovery angle (CRA), tearing strength (TE), and whiteness index (WI). The optimum parameters (values) for resin finishing were the resin concentration (80 g·L−1), the polyethylene softener (40 g·L−1), the catalyst (25 g·L−1), the curing temperature (140 °C), and the curing time (2 min). The goodness-of-fit of the data was validated by an analysis of variance (ANOVA). The optimized sample was characterized by Fourier-transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), and scanning electron microscope (SEM) to better understand the structural details of the resin finishing process. The results showed an improved thermal stability and confirmed the presence of well deposited of resin on the optimized fabric surface. PMID:29543724

Research on error control and compensation in magnetorheological finishing.

PubMed

Dai, Yifan; Hu, Hao; Peng, Xiaoqiang; Wang, Jianmin; Shi, Feng

2011-07-01

Although magnetorheological finishing (MRF) is a deterministic finishing technology, the machining results always fall short of simulation precision in the actual process, and it cannot meet the precision requirements just through a single treatment but after several iterations. We investigate the reasons for this problem through simulations and experiments. Through controlling and compensating the chief errors in the manufacturing procedure, such as removal function calculation error, positioning error of the removal function, and dynamic performance limitation of the CNC machine, the residual error convergence ratio (ratio of figure error before and after processing) in a single process is obviously increased, and higher figure precision is achieved. Finally, an improved technical process is presented based on these researches, and the verification experiment is accomplished on the experimental device we developed. The part is a circular plane mirror of fused silica material, and the surface figure error is improved from the initial λ/5 [peak-to-valley (PV) λ=632.8 nm], λ/30 [root-mean-square (rms)] to the final λ/40 (PV), λ/330 (rms) just through one iteration in 4.4 min. Results show that a higher convergence ratio and processing precision can be obtained by adopting error control and compensation techniques in MRF.

National machine guarding program: Part 1. Machine safeguarding practices in small metal fabrication businesses

PubMed Central

Yamin, Samuel C.; Brosseau, Lisa M.; Xi, Min; Gordon, Robert; Most, Ivan G.; Stanley, Rodney

2015-01-01

Background Metal fabrication workers experience high rates of traumatic occupational injuries. Machine operators in particular face high risks, often stemming from the absence or improper use of machine safeguarding or the failure to implement lockout procedures. Methods The National Machine Guarding Program (NMGP) was a translational research initiative implemented in conjunction with two workers' compensation insures. Insurance safety consultants trained in machine guarding used standardized checklists to conduct a baseline inspection of machine‐related hazards in 221 business. Results Safeguards at the point of operation were missing or inadequate on 33% of machines. Safeguards for other mechanical hazards were missing on 28% of machines. Older machines were both widely used and less likely than newer machines to be properly guarded. Lockout/tagout procedures were posted at only 9% of machine workstations. Conclusions The NMGP demonstrates a need for improvement in many aspects of machine safety and lockout in small metal fabrication businesses. Am. J. Ind. Med. 58:1174–1183, 2015. © 2015 The Authors. American Journal of Industrial Medicine published by Wiley Periodicals, Inc. PMID:26332060

Center removal amount control of magnetorheological finishing process by spiral polishing way

NASA Astrophysics Data System (ADS)

Wang, Yajun; He, Jianguo; Ji, Fang; Huang, Wen; Xiao, Hong; Luo, Qing; Zheng, Yongcheng

2010-10-01

Spiral polishing is a traditional process of computer-controlled optical surfacing. However, the additional polishing amount is great and the center polishing amount is difficult to control. At first, a simplified mathematics model is presented for magnetorheological finishing, which indicates that the center polishing amount and additional polishing amount are proportional to the length and peak value of magnetorheological finishing influence function, and are inversely proportional to pitch and rotation rate of spiral track, and the center polishing amount is much bigger than average polishing amount. Secondly, the relationships of "tool feed way and center polishing amount", "spiral pitch and calculation accuracy of influence matrix for dwell time function solution", "spiral pitch and center polishing amount" and "peak removal rate, dimensions of removal function and center removal amount" are studied by numerical computation by Archimedes spiral path. It shows that the center polishing amount is much bigger in feed stage than that in backhaul stage when the head of influence function is towards workpiece edge in feeding; and the bigger pitch, the bigger calculation error of influence matrix elements; and the bigger pitch, the smaller center polishing amount, and the smaller peak removal rate and dimensions of removal function, the smaller center removal amount. At last, the polishing results are given, which indicates that the center polishing amount is acceptable with a suitable polishing amount rate of feed stage and backhaul stage, and with a suitable spiral pitch during magnetorheological finishing procedure by spiral motion way.

Phytotoxicity of floodplain soils contaminated with trace metals along the Clark Fork River, Grant-Kohrs Ranch National Historic Site, Deer Lodge, Montana, USA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rader, B.R.; Nimmo, D.W.R.; Chapman, P.L.

1997-07-01

Concentrations of metals in sediments and soils deposited along the floodplain of the Clark Fork River, within the Grant-Kohrs Ranch National Historic Site, Deer Lodge, Montana, USA, have exceeded maximum background concentrations in the United States for most metals tested. As a result of mining and smelting activities, portions of the Deer Lodge Valley, including the Grant-Kohrs Ranch, have received National Priority List Designation under the Comprehensive Environmental Response, Compensation and Liability Act. Using a series of plant germination tests, pH measurements, and metal analyses, this study investigated the toxicity of soils from floodplain slicken areas, bare spots devoid ofmore » vegetation, along the Clark Fork River. The slicken soils collected from the Grant-Kohrs Ranch were toxic to all four plant species tested. The most sensitive endpoint in the germination tests was root length and the least sensitive was emergence. Considering emergence, the most sensitive species was the resident grass species Agrostis gigantea. The sensitivities were reversed when root lengths were examined, with Echinochloa crusgalli showing the greatest sensitivity. Both elevated concentrations of metals and low pH were necessary to produce an acutely phytotoxic response in laboratory seed germination tests using slicken soils. Moreover, pH values on the Grant-Kohrs Ranch appear to be a better predictor of acutely phytotoxic conditions than total metal levels.« less

The Effect of Composition on the Surface Finish of PS400: A New High Temperature Solid Lubricant Coating

NASA Technical Reports Server (NTRS)

DellaCorte, Christopher; Stanford, malcolm K.; Thomas, Fransua; Edmonds, Brian J.

2010-01-01

A new composite, multi-constituent, solid lubricant coating, NASA PS400, developed for high temperature tribological applications, exhibits a smoother surface finish after grinding and polishing than its predecessors PS200 and PS300. In this paper, the baseline composition of PS400 is modified to investigate each individual constituent s role on the achievable surface finish through a series of coating deposition, grinding, and polishing experiments. Furthermore, to explore the limits of compositional tailoring for improved tribological performance, several PS400 coatings were doped with additional solid lubricants (graphite, MoS2 and BN) and tribologically tested. The test results clearly showed that, compared to PS300 coatings, PS400 achieves a smoother surface finish via a reduced lubricant content. Coatings prepared with higher than the baseline level (10 wt%) of lubricants exhibited higher final surface roughness than the earlier generation PS300 coatings. Reducing or eliminating the one or both lubricants (fluorides or silver) did not further improve the surface finish suggesting that the current composition of PS400 is near optimal with respect to surface finish. Lastly, attempts to improve the poor initial room temperature tribological behavior of PS400 via the addition of traditional solid lubricants were unsuccessful. Based upon this work and earlier results it is expected that future research will concentrate on developing methods to produce a lubricious glaze on the rubbing surface during break in to ensure that low friction and wear are rapidly achieved.

Clinical outcomes for patients finished with the SureSmile™ method compared with conventional fixed orthodontic therapy.

PubMed

Alford, Timothy J; Roberts, W Eugene; Hartsfield, James K; Eckert, George J; Snyder, Ronald J

2011-05-01

Utilize American Board of Orthodontics (ABO) cast/radiographic evaluation (CRE) to compare a series of 63 consecutive patients, finished with manual wire bending (conventional) treatment, vs a subsequent series of 69 consecutive patients, finished by the same orthodontist using the SureSmile™ (SS) method. Records of 132 nonextraction patients were scored by a calibrated examiner blinded to treatment mode. Age and discrepancy index (DI) between groups were compared by t-tests. A chi-square test was used to compare for differences in sex and whether the patient was treated using braces only (no orthopedic correction). Analysis of covariance tested for differences in CRE outcomes and treatment times, with sex and DI included as covariates. A logarithmic transformation of CRE outcomes and treatment times was used because their distributions were skewed. Significance was defined as P < .05. Compared with conventional finishing, SS patients had significantly lower DI scores, less treatment time (∼7 months), and better CRE scores for first-order alignment-rotation and interproximal space closure; however, second-order root angulation (RA) was inferior. SS patients were treated in less time to better CRE scores for first-order rotation (AR) and interproximal space closure (IC) but on the average, malocclusions were less complex and second order root alignment was inferior, compared with patients finished with manual wire bending.

Clinical outcomes for patients finished with the SureSmile™ method compared with conventional fixed orthodontic therapy

PubMed Central

Alford, Timothy J.; Roberts, W. Eugene; Hartsfield, James K.; Eckert, George J.; Snyder, Ronald J.

2016-01-01

Objective Utilize American Board of Orthodontics (ABO) cast/radiographic evaluation (CRE) to compare a series of 63 consecutive patients, finished with manual wire bending (conventional) treatment, vs a subsequent series of 69 consecutive patients, finished by the same orthodontist using the SureSmile™ (SS) method. Materials and Methods Records of 132 nonextraction patients were scored by a calibrated examiner blinded to treatment mode. Age and discrepancy index (DI) between groups were compared by t-tests. A chi-square test was used to compare for differences in sex and whether the patient was treated using braces only (no orthopedic correction). Analysis of covariance tested for differences in CRE outcomes and treatment times, with sex and DI included as covariates. A logarithmic transformation of CRE outcomes and treatment times was used because their distributions were skewed. Significance was defined as P < .05. Results Compared with conventional finishing, SS patients had significantly lower DI scores, less treatment time (~7 months), and better CRE scores for first-order alignment-rotation and interproximal space closure; however, second-order root angulation (RA) was inferior. Conclusion SS patients were treated in less time to better CRE scores for first-order rotation (AR) and interproximal space closure (IC) but on the average, malocclusions were less complex and second order root alignment was inferior, compared with patients finished with manual wire bending. PMID:21261488

Eradication of Mycoplasma hyopneumoniae from a swine finishing herd without total depopulation.

PubMed

Heinonen, Mari; Laurila, Tapio; Vidgren, Gabriele; Levonen, Katri

2011-04-01

Using vaccination and medication, Mycoplasma hyopneumoniae (Mhyo) was eradicated from a finishing herd without total depopulation. Altogether 3243 feeder pigs originating from Mhyo-free herds were vaccinated once using an inactivated, adjuvanted vaccine before transporting them to a Mhyo-infected finishing herd. The Mhyo-infected groups of pigs were medicated with antimicrobial agents at the time of the arrival of the first groups of Mhyo-free, vaccinated feeder pigs. The groups were operated with an all-in-all-out method in rooms with separate ventilation and slurry disposal systems. Thereafter the farmer purchased only non-vaccinated feeder pigs originating from Mhyo-free sow herds. Serology gave no positive results for 5.5 years and it was concluded that the eradication programme had been successful in producing a Mhyo-free herd without total depopulation. Copyright © 2010 Elsevier Ltd. All rights reserved.

Surface Fatigue Lives of Case-Carburized Gears With an Improved Surface Finish

NASA Technical Reports Server (NTRS)

Krantz, T. L.; Alanou, M. P.; Evans, H. P.; Snidle, R. W.; Krantz, T. L. (Technical Monitor)

2000-01-01

Previous research provides qualitative evidence that an improved surface finish can increase the surface fatigue lives of gears. To quantify the influence of surface roughness on life, a set of AISI 93 10 steel gears was provided with a nearmirror finish by superfinishing. The effects of the superfinishing on the quality of the gear tooth surfaces were determined using data from metrology, profilometry, and interferometric microscope inspections. The superfinishing reduced the roughness average by about a factor of 5. The superfinished gears were subjected to surface fatigue testing at 1.71 -GPa (248-ksi) Hertz contact stress, and the data were compared with the NASA Glenn gear fatigue data base. The lives of gears with superfinished teeth were about four times greater compared with the lives of gears with ground teeth but with otherwise similar quality.

Estimation of tool wear length in finish milling using a fuzzy inference algorithm

NASA Astrophysics Data System (ADS)

Ko, Tae Jo; Cho, Dong Woo

1993-10-01

The geometric accuracy and surface roughness are mainly affected by the flank wear at the minor cutting edge in finish machining. A fuzzy estimator obtained by a fuzzy inference algorithm with a max-min composition rule to evaluate the minor flank wear length in finish milling is introduced. The features sensitive to minor flank wear are extracted from the dispersion analysis of a time series AR model of the feed directional acceleration of the spindle housing. Linguistic rules for fuzzy estimation are constructed using these features, and then fuzzy inferences are carried out with test data sets under various cutting conditions. The proposed system turns out to be effective for estimating minor flank wear length, and its mean error is less than 12%.

Kinetic model for the formation of acrylamide during the finish-frying of commercial french fries.

PubMed

Parker, Jane K; Balagiannis, Dimitrios P; Higley, Jeremy; Smith, Gordon; Wedzicha, Bronislaw L; Mottram, Donald S

2012-09-12

Acrylamide is formed from reducing sugars and asparagine during the preparation of French fries. The commercial preparation of French fries is a multistage process involving the preparation of frozen, par-fried potato strips for distribution to catering outlets, where they are finish-fried. The initial blanching, treatment in glucose solution, and par-frying steps are crucial because they determine the levels of precursors present at the beginning of the finish-frying process. To minimize the quantities of acrylamide in cooked fries, it is important to understand the impact of each stage on the formation of acrylamide. Acrylamide, amino acids, sugars, moisture, fat, and color were monitored at time intervals during the frying of potato strips that had been dipped in various concentrations of glucose and fructose during a typical pretreatment. A mathematical model based on the fundamental chemical reaction pathways of the finish-frying was developed, incorporating moisture and temperature gradients in the fries. This showed the contribution of both glucose and fructose to the generation of acrylamide and accurately predicted the acrylamide content of the final fries.

91. Neg. No. F174A, Apr 24, 1936, INTERIORASSEMBLY BUILDING, FINISHED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

91. Neg. No. F-174A, Apr 24, 1936, INTERIOR-ASSEMBLY BUILDING, FINISHED CARS AT THE END OF THE ASSEMBLY LINE - Ford Motor Company Long Beach Assembly Plant, Assembly Building, 700 Henry Ford Avenue, Long Beach, Los Angeles County, CA

Heavy metal contents in water, sediment and fish in a karst aquatic ecosystem of the Plitvice Lakes National Park (Croatia).

PubMed

Vukosav, Petra; Mlakar, Marina; Cukrov, Neven; Kwokal, Zeljko; Pižeta, Ivanka; Pavlus, Natalija; Spoljarić, Ivanka; Vurnek, Maja; Brozinčević, Andrijana; Omanović, Dario

2014-03-01

An evaluation of the quality status of the pristine karst, tufa depositing aquatic environment of the Plitvice Lakes National Park based on the analysis of heavy (ecotoxic) metals was examined for the first time. Analyses of trace metals in water, sediment and fish (Salmo trutta, Oncorhynchus mykiss, Squalius cephalus) samples were conducted either by stripping voltammetry (Zn, Cd, Pb and Cu) or cold vapour atomic absorption spectrometry (Hg). The concentration of dissolved trace metals in water was very low revealing a pristine aquatic environment (averages were, in ng/L: 258 (Zn), 10.9 (Cd), 11.7 (Pb), 115 (Cu) and 1.22 (Hg)). Slightly enhanced concentrations of Cd (up to 50 ng/L) and Zn (up to 900 ng/L) were found in two main water springs and are considered as of natural origin. Observed downstream decrease in concentration of Cd, Zn and Cu in both water and sediments is a consequence of the self-purification process governed by the formation and settling of authigenic calcite. Anthropogenic pressure was spotted only in the Kozjak Lake: Hg concentrations in sediments were found to be up to four times higher than the baseline value, while at two locations, Pb concentrations exceeded even a probable effect concentration. The increase of Hg and Pb was not reflected on their levels in the fish tissues; however, significant correlations were found between Cd level in fish tissues (liver and muscle) and in the water/sediment compartments, while only partial correlations were estimated for Zn and Cu. A high discrepancy between values of potentially bioavailable metal fraction estimated by different modelling programs/models raised the question about the usefulness of these data as a parameter in understanding/relating the metal uptake and their levels in aquatic organism. The aquatic environment of the Plitvice Lakes National Park is characterized, in general, as a clean ecosystem.

Consumer sensory evaluation and chemical composition of beef gluteus medius and triceps brachii steaks from cattle finished on forage or concentrate diets.

PubMed

Chail, A; Legako, J F; Pitcher, L R; Ward, R E; Martini, S; MacAdam, J W

2017-04-01

The objective of this study was to assess the impact of cattle finishing diet and muscle type on meat quality. Consumer sensory response, proximate composition, Warner-Bratzler shear force (WBSF), fatty acid composition, and volatile compounds were assessed from the gluteus medius (GM) and triceps brachii (TB) muscles of cattle ( = 6 per diet) which were grain-finished (USUGrain) on conventional feedlot or 2 forage diets, a perennial legume, birdsfoot trefoil-finished (USUBFT; ), and grass-finished (USUGrass; ). Diet had an interacting effect with muscle for all sensory attributes ( ≤ 0.002), except aroma and flavor ( ≥ 0.078). In forage-finished beef, tenderness, fattiness, overall liking, and WBSF tenderness of GM was greater ( < 0.05) than TB, whereas for USUGrain, the tenderness, fattiness, overall liking, and WBSF tenderness of both muscles were similar ( > 0.05) but the juiciness of TB was more liked than USUGrain GM ( < 0.05). The juiciness of forage-finished beef did not differ ( > 0.05) between GM and TB. Lower ( < 0.05) intramuscular fat (IMF) percent was determined for USUGrass beef in comparison with USUGrain beef. The IMF percent of USUBFT beef was similar ( > 0.05) to both USUGrass and USUGrain beef. However, IMF percent was not impacted by muscle type ( = 0.092). The ratio of -6:-3 fatty acids was affected by muscle dependent on diet ( = 0.016). The ratio of -6:-3 fatty acids was affected by the interaction of muscle × diet ( = 0.016). Between forage diets (USUGrass and USUBFT), -6:-3 ratios were similar ( > 0.05) between GM and TB, whereas within USUGrain, the GM was greater ( < 0.05) than the TB. Cumulative MUFA was greater ( < 0.05) in USUGrain compared with both USUGrass and USUBFT, which were similar ( > 0.05). Strecker aldehydes, ketones, pyrazines, and methional were affected ( ≤ 0.036) by muscle and found to have a greater concentration in GM compared with TB. Overall, consumers determined that USUGrain GM and TB had similar ( > 0

40 CFR 425.30 - Applicability; description of the hair save or pulp, non-chrome tan, retan-wet finish subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Applicability; description of the hair save or pulp, non-chrome tan, retan-wet finish subcategory. 425.30 Section 425.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING POINT SOURCE CATEGORY Hair Save...

Estimation and characterization of decontamination and decommissioning solid waste expected from the Plutonium Finishing Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Millar, J.S.; Pottmeyer, J.A.; Stratton, T.J.

1995-01-01

Purpose of the study was to estimate the amounts of equipment and other materials that are candidates for removal and subsequent processing in a solid waste facility when the Hanford Plutonium Finishing Plant is decontaminated and decommissioned. (Building structure and soil are not covered.) Results indicate that {approximately}5,500 m{sup 3} of solid waste is expected to result from the decontamination and decommissioning of the Pu Finishing Plant. The breakdown of the volumes and percentages of waste by category is 1% dangerous solid waste, 71% low-level waste, 21% transuranic waste, 7% transuranic mixed waste.

Construction Occupations--Finishing. Reprinted from the Occupational Outlook Handbook, 1978-79 Edition.

ERIC Educational Resources Information Center

Bureau of Labor Statistics (DOL), Washington, DC.

Focusing on finishing construction occupations, this document is one in a series of forty-one reprints from the Occupational Outlook Handbook providing current information and employment projections for individual occupations and industries through 1985. The specific occupations covered in this document include air…

40 CFR 410.50 - Applicability; description of the knit fabric finishing subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Applicability; description of the knit fabric finishing subcategory. 410.50 Section 410.50 Protection of Environment ENVIRONMENTAL PROTECTION... operations: Bleaching, mercerizing, dyeing, printing, resin treatment, water proofing, flame proofing, soil...

Anthropogenic Organic Compounds in Ground Water and Finished Water of Community Water Systems in the Northern Tampa Bay Area, Florida, 2002-04

USGS Publications Warehouse

Metz, Patricia A.; Delzer, Gregory C.; Berndt, Marian P.; Crandall, Christy A.; Toccalino, Patricia L.

2007-01-01

As part of the U.S. Geological Survey's (USGS's) National Water-Quality Assessment (NAWQA) Program, a Source Water-Quality Assessment (SWQA) was conducted in the unconfined and semiconfined portions of the Upper Floridan aquifer system during 2002-04. SWQAs are two-phased sampling activities, wherein phase 1 was designed to evaluate the occurrence of 258 anthropogenic organic compounds (AOCs) in ground water used as source water for 30 of the largest-producing community water system (CWS) wells in the northern Tampa Bay area, Florida. The 258 AOCs included volatile organic compounds (VOCs), pesticides, and other anthropogenic organic compounds (OAOCs). Phase 2 was designed to monitor concentrations in the source water and also the finished water of CWSs for compounds most frequently detected during phase 1. During phase 1 of the SWQA study, 31 of the 258 AOCs were detected in source-water samples collected from CWS wells at low concentrations (less than 1.0 microgram per liter (ug/L)). Twelve AOCs were detected in at least 10 percent of samples. Concentrations from 16 of the 31 detected AOCs were about 2 to 5 orders of magnitude below human-health benchmarks indicating that concentrations were unlikely to be of potential human-health concern. The potential human-health relevance for the remaining 15 detected unregulated AOCs could not be evaluated because no human-health benchmarks were available for these compounds. Hydrogeology, population, and land use were examined to evaluate the effects of these variables on the source water monitored. Approximately three times as many detections of VOCs (27) and pesticides (34) occurred in unconfined areas than in the semiconfined areas (8 VOCs, 14 pesticides). In contrast, 1 OAOC was detected in unconfined areas, and 13 OAOCs were detected in semiconfined areas with 9 of the OAOC detections occurring in samples from two wells located near septic systems. Analyses of population and land use indicated that the number of

29 CFR 1910.107 - Spray finishing using flammable and combustible materials.

Code of Federal Regulations, 2012 CFR

2012-07-01

... finishing material. (5) Dry spray booth. A spray booth not equipped with a water washing system as described in subparagraph (4) of this paragraph. A dry spray booth may be equipped with (i) distribution or... it enters the exhaust duct; or (ii) overspray dry filters to minimize dusts; or (iii) overspray dry...

29 CFR 1910.107 - Spray finishing using flammable and combustible materials.

Code of Federal Regulations, 2014 CFR

2014-07-01

... finishing material. (5) Dry spray booth. A spray booth not equipped with a water washing system as described in subparagraph (4) of this paragraph. A dry spray booth may be equipped with (i) distribution or... it enters the exhaust duct; or (ii) overspray dry filters to minimize dusts; or (iii) overspray dry...

29 CFR 1910.107 - Spray finishing using flammable and combustible materials.

Code of Federal Regulations, 2013 CFR

2013-07-01

... finishing material. (5) Dry spray booth. A spray booth not equipped with a water washing system as described in subparagraph (4) of this paragraph. A dry spray booth may be equipped with (i) distribution or... it enters the exhaust duct; or (ii) overspray dry filters to minimize dusts; or (iii) overspray dry...

Finishing: Construction Industry Series: Preparation Level: Student Manual and Instructor's Guide.

ERIC Educational Resources Information Center

Texas Education Agency, Austin. Dept. of Occupational Education and Technology.

The guide is an outline of training experiences designed to lead a student to at least entry-level job proficiency in the finishing trades within the construction industry. Teaching units cover insulating, drywall, painting and wall covering, glass and glazing, floor covering, and landscaping. Each unit has several overall objectives which are…

Effects of Surface Finishes and Current Stressing on Interfacial Reaction Characteristics of Sn-3.0Ag-0.5Cu Solder Bumps

NASA Astrophysics Data System (ADS)

Kim, Jae-Myeong; Jeong, Myeong-Hyeok; Yoo, Sehoon; Park, Young-Bae

2012-04-01

The effects of surface finishes on the in situ interfacial reaction characteristics of ball grid array (BGA) Sn-3.0Ag-0.5Cu lead-free solder bumps were investigated under annealing and electromigration (EM) test conditions of 130°C to 175°C with 5.0 × 103 A/cm2. During reflow and annealing, (Cu,Ni)6Sn5 intermetallic compound (IMC) formed at the interface of electroless nickel immersion gold (ENIG) finish. In the case of both immersion Sn and organic solderability preservative (OSP) finishes, Cu6Sn5 and Cu3Sn IMCs formed. Overall, the IMC growth velocity of ENIG was much lower than that of the other finishes. The activation energies of total IMCs were found to be 0.52 eV for ENIG, 0.78 eV for immersion Sn, and 0.72 eV for OSP. The ENIG finish appeared to present an effective diffusion barrier between the Cu substrate and the solder, which leads to better EM reliability in comparison with Cu-based pad systems. The failure mechanisms were explored in detail via in situ EM tests.

Daidzein enhances intramuscular fat deposition and improves meat quality in finishing steers

PubMed Central

Zhao, Xiang-Hui; Yang, Zhu-Qing; Bao, Lin-Bin; Wang, Can-Yu; -Zhou, Shan; Gong, Jian-Ming; Fu, Chuan-Bian; Xu, Lan-Jiao; Liu, Chan-Juan

2015-01-01

An experiment was conducted to determine the effects of soy isoflavone daidzein on carcass characteristics, fat deposition, meat quality, and blood metabolites in finishing steers. Fourteen crossbred steers were used in a 120-d finishing study. These steers were stratified by weight into groups and randomly allotted by group to one of two dietary treatments: (1) control and (2) daidzein (500 mg/kg concentrate). The steers were fed a 90% concentrate diet. Supplemental daidzein did not affect slaughter weight, hot carcass weight, and dressing percentage, but tended to reduce fat proportion (not including intramuscular fat) in carcass and backfat thickness of steers. The carcass bone proportion was greater in steers fed daidzein diets than those fed control diets. Daidzein supplementation reduced pH at 24 h after slaughtered and moisture content and increased isocitrate dehydrogenase activity, fat content (16.28% and 7.94%), marbling score (5.29 and 3.36), redness (a*), and chroma (C*) values in longissimus muscle relative to control treatment. The concentrations of blood metabolites including glucose, blood urea nitrogen, triglyceride, total cholesterol, non-esterified fatty acid, high-density lipoprotein cholesterol (HDL-C), and low-density lipoprotein cholesterol (LDL-C) were all lower in steers fed daidzein diets than those fed control diets. Current results suggest that supplemental daidzein can affect lipid metabolism, increase intramuscular fat content and marbling score, and improve meat quality in finishing steers. Daidzein should be a promising feed additive for production of high-quality beef meat. PMID:25526906

Indirect Fabrication of Lattice Metals with Thin Sections Using Centrifugal Casting.

PubMed

Mun, Jiwon; Ju, Jaehyung; Thurman, James

2016-05-14

One of the typical methods to manufacture 3D lattice metals is the direct-metal additive manufacturing (AM) process such as Selective Laser Melting (SLM) and Electron Beam Melting (EBM). In spite of its potential processing capability, the direct AM method has several disadvantages such as high cost, poor surface finish of final products, limitation in material selection, high thermal stress, and anisotropic properties of parts. We propose a cost-effective method to manufacture 3D lattice metals. The objective of this study is to provide a detailed protocol on fabrication of 3D lattice metals having a complex shape and a thin wall thickness; e.g., octet truss made of Al and Cu alloys having a unit cell length of 5 mm and a cell wall thickness of 0.5 mm. An overall experimental procedure is divided into eight sections: (a) 3D printing of sacrificial patterns (b) melt-out of support materials (c) removal of residue of support materials (d) pattern assembly (e) investment (f) burn-out of sacrificial patterns (g) centrifugal casting (h) post-processing for final products. The suggested indirect AM technique provides the potential to manufacture ultra-lightweight lattice metals; e.g., lattice structures with Al alloys. It appears that the process parameters should be properly controlled depending on materials and lattice geometry, observing the final products of octet truss metals by the indirect AM technique.

Effect finishing and polishing procedures on the surface roughness of IPS Empress 2 ceramic.

PubMed

Boaventura, Juliana Maria Capelozza; Nishida, Rodrigo; Elossais, André Afif; Lima, Darlon Martins; Reis, José Mauricio Santos Nunes; Campos, Edson Alves; de Andrade, Marcelo Ferrarezi

2013-01-01

To evaluate the surface roughness of IPS Empress 2 ceramic when treated with different finishing/polishing protocols. Sixteen specimens of IPS Empress 2 ceramic were made from wax patterns obtained using a stainless steel split mold. The specimens were glazed (Stage 0-S0, control) and divided into two groups. The specimens in Group 1 (G1) were finished/polished with a KG Sorensen diamond point (S1), followed by KG Sorensen siliconized points (S2) and final polishing with diamond polish paste (S3). In Group 2 (G2), the specimens were finished/polished using a Shofu diamond point (S1), as well as Shofu siliconized points (S2) and final polishing was performed using Porcelize paste (S3). After glazing (S0) and following each polishing procedure (S1, S2 or S3), the surface roughness was measured using TALYSURF Series 2. The average surface roughness results were analyzed using ANOVA followed by Tukey post-hoc tests (α = 0.01) RESULTS: All of the polishing procedures yielded higher surface roughness values when compared to the control group (S0). S3 yielded lower surface roughness values when compared to S1 and S2. The proposed treatments negatively affected the surface roughness of the glazed IPS Empress 2 ceramic.

Phytotoxicity of floodplain soils contaminated with trace metals along the clark fork river, Grant-Kohrs Ranch National Historic Site, Deer Lodge, Montana, United States

USGS Publications Warehouse

Rader, B.R.; Nimmo, D.W.R.; Chapman, P.L.

1997-01-01

Concentrations of metals in sediments and soils deposited along the floodplain of the Clark Fork River, within the Grant-Kohrs Ranch National Historic Site, Deer Lodge, Montana, USA, have exceeded maximum background concentrations in the United States for most metals tested. As a result of mining and smelting activities, portions of the Deer Lodge Valley, including the Grant-Kohrs Ranch, have received National Priority List Designation under the Comprehensive Environmental Response, Compensation and Liability Act. Using a series of plant germination tests, pH measurements, and metal analyses, this study investigated the toxicity of soils from floodplain 'slicken' areas, bare spots devoid of vegetation, along the Clark Fork River. The slicken soils collected from the Grant-Kohrs Ranch were toxic to all four plant species tested. The most sensitive endpoint in the germination tests was root length and the least sensitive was emergence. Considering emergence, the most sensitive species was the resident grass species Agrostis gigantea. The sensitivities were reversed when root lengths were examined, with Echinochloa crusgalli showing the greatest sensitivity. Both elevated concentrations of metals and low pH were necessary to produce an acutely phytotoxic response in laboratory seed germination tests using slicken soils. Moreover, pH values on the Grant-Kohrs Ranch appear to be a better predictor of acutely phytotoxic conditions than total metal levels.

A survey of grass-finished beef producers in the northeastern U.S.

USDA-ARS?s Scientific Manuscript database

Sixty-nine self-identified grass-finished beef producers responded to an online survey implemented via email listservs in the Northeast. Fifty-four records from producers in Maine, Massachusetts, New Hampshire, New York, Pennsylvania, Vermont, and West Virginia were included in the analysis after ex...

Environmental assessment of a representative grass-finishing beef operation in southern Pennsylvania

USDA-ARS?s Scientific Manuscript database

The objective of this study was to quantify environmental impacts of a representative grass-finished beef operation in southeastern Pennsylvania. A farm-gate life cycle assessment was conducted using the Integrated Farm System Model to estimate greenhouse gas emissions, reactive nitrogen loss, and w...

Trace metals related to historical iron smelting at Hopewell Furnace National Historic Site, Berks and Chester Counties, Pennsylvania

USGS Publications Warehouse

Sloto, Ronald A.

2011-01-01

Iron ore containing elevated concentrations of trace metals was smelted at Hopewell Furnace during its 113 years of operation (1771-1883). The ore used at Hopewell Furnace was obtained from iron mines within 5 miles of the furnace. The iron-ore deposits were formed about 200 million years ago and contain abundant magnetite, the primary iron mineral, and accessory minerals enriched in arsenic, cobalt, copper, lead, and other metals. Hopewell Furnace, built by Mark Bird during 1770-71, was one of the last of the charcoal-burning, cold-blast iron furnaces operated in Pennsylvania. The most productive years for Hopewell Furnace were from 1830 to 1837. Castings were the most profitable product, especially the popular Hopewell Stove. More than 80,000 stoves were cast at Hopewell, which produced as many as 23 types and sizes of cooking and heating stoves. Beginning in the 1840s, the iron industry shifted to large-scale, steam-driven coke and anthracite furnaces. Independent rural enterprises like Hopewell could no longer compete when the iron and steel industries consolidated in urban manufacturing centers. The furnace ceased operation in 1883 (Kurjack, 1954). The U.S. Geological Survey (USGS), in cooperation with the National Park Service, completed a study at Hopewell Furnace National Historic Site (NHS) in Berks and Chester Counties, Pennsylvania, to determine the fate of toxic trace metals, such as arsenic, cobalt, and lead, released into the environment during historical iron-smelting operations. The results of the study, conducted during 2008-10, are presented in this fact sheet.

45. FINISHING STANDS, 98INCH CONTINUOUS HOT STRIP MILL, WORLD'S LARGEST ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

45. FINISHING STANDS, 98-INCH CONTINUOUS HOT STRIP MILL, WORLD'S LARGEST AT THE TIME OF INSTALLATION IN 1937. THE MILL WAS REPLACED BY A NEW 84-INCH MILL IN 1971 AND IS SEEN HERE PARTIALLY DISMANTLED IN PREPARATION FOR DEMOLITION. - Corrigan, McKinney Steel Company, 3100 East Forty-fifth Street, Cleveland, Cuyahoga County, OH

Magnetorheological finishing (MRF) of potassium dihydrogen phosphate (KDP) crystals: nonaqueous fluids development, optical finish, and laser damage performance at 1064 nm and 532 nm

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menapace, J A; Ehrmann, P R; Bickel, R C

2009-11-05

Over the past year we have been working on specialized MR fluids for polishing KDP crystals. KDP is an extremely difficult material to conventionally polish due to its water solubility, low hardness, and temperature sensitivity. Today, KDP crystals are finished using single-point diamond turning (SPDT) tools and nonaqueous lubricants/coolants. KDP optics fabricated using SPDT, however, are limited to surface corrections due to tool/method characteristics with surface quality driven by microroughness from machine pitch, speed, force, and diamond tool character. MRF polishing offers a means to circumvent many of these issues since it is deterministic which makes the technique practical formore » surface and transmitted wavefront correction, is low force, and is temperature independent. What is lacking is a usable nonaqueous MR fluid that is chemically and physically compatible with KDP which can be used for polishing and subsequently cleaned from the optical surface. In this study, we will present the fluid parameters important in the design and development of nonaqueous MR fluid formulations capable of polishing KDP and how these parameters affect MRF polishing. We will also discuss requirements peculiar to successful KDP polishing and how they affect optical figure/finish and laser damage performance at 1064 nm and 532 nm.« less

Magnetorheological finishing (MRF) of potassium dihydrogen phosphate (KDP) crystals: nonaqueous fluids development, optical finish, and laser damage performance at 1064 nm and 532 nm

NASA Astrophysics Data System (ADS)

Menapace, J. A.; Ehrmann, P. R.; Bickel, R. C.

2009-10-01

Over the past year we have been working on specialized MR fluids for polishing KDP crystals. KDP is an extremely difficult material to conventionally polish due to its water solubility, low hardness, and temperature sensitivity. Today, KDP crystals are finished using single-point diamond turning (SPDT) tools and nonaqueous lubricants/coolants. KDP optics fabricated using SPDT, however, are limited to surface corrections due to tool/method characteristics with surface quality driven by microroughness from machine pitch, speed, force, and diamond tool character. MRF polishing offers a means to circumvent many of these issues since it is deterministic which makes the technique practical for surface and transmitted wavefront correction, is low force, and is temperature independent. What is lacking is a usable nonaqueous MR fluid that is chemically and physically compatible with KDP which can be used for polishing and subsequently cleaned from the optical surface. In this study, we will present the fluid parameters important in the design and development of nonaqueous MR fluid formulations capable of polishing KDP and how these parameters affect MRF polishing. We will also discuss requirements peculiar to successful KDP polishing and how they affect optical figure/finish and laser damage performance at 1064 nm and 532 nm.

Printed Circuit Board Surface Finish and Effects of Chloride Contamination, Electric Field, and Humidity on Corrosion Reliability

NASA Astrophysics Data System (ADS)

Conseil-Gudla, Hélène; Jellesen, Morten S.; Ambat, Rajan

2017-02-01

Corrosion reliability is a serious issue today for electronic devices, components, and printed circuit boards (PCBs) due to factors such as miniaturization, globalized manufacturing practices which can lead to process-related residues, and global usage effects such as bias voltage and unpredictable user environments. The investigation reported in this paper focuses on understanding the synergistic effect of such parameters, namely contamination, humidity, PCB surface finish, pitch distance, and potential bias on leakage current under different humidity levels, and electrochemical migration probability under condensing conditions. Leakage currents were measured on interdigitated comb test patterns with three different types of surface finish typically used in the electronics industry, namely gold, copper, and tin. Susceptibility to electrochemical migration was studied under droplet conditions. The level of base leakage current (BLC) was similar for the different surface finishes and NaCl contamination levels up to relative humidity (RH) of 65%. A significant increase in leakage current was found for comb patterns contaminated with NaCl above 70% to 75% RH, close to the deliquescent RH of NaCl. Droplet tests on Cu comb patterns with varying pitch size showed that the initial BLC before dendrite formation increased with increasing NaCl contamination level, whereas electrochemical migration and the frequency of dendrite formation increased with bias voltage. The effect of different surface finishes on leakage current under humid conditions was not very prominent.

Influence law of structural characteristics on the surface roughness of a magnetorheological-finished KDP crystal.

PubMed

Chen, Shaoshan; Li, Shengyi; Hu, Hao; Li, Qi; Tie, Guipeng

2014-11-01

A new nonaqueous and abrasive-free magnetorheological finishing (MRF) method is adopted for processing potassium dihydrogen phosphate (KDP) crystal due to its low hardness, high brittleness, temperature sensitivity, and water solubility. This paper researches the influence of structural characteristics on the surface roughness of MRF-finished KDP crystal. The material removal by dissolution is uniform layer by layer when the polishing parameters are stable. The angle between the direction of the polishing wheel's linear velocity and the initial turning lines will affect the surface roughness. If the direction is perpendicular to the initial turning lines, the polishing can remove the lines. If the direction is parallel to the initial turning lines, the polishing can achieve better surface roughness. The structural characteristic of KDP crystal is related to its internal chemical bonds due to its anisotropy. During the MRF finishing process, surface roughness will be improved if the structural characteristics of the KDP crystal are the same on both sides of the wheel. The processing results of (001) plane crystal show we can get the best surface roughness (RMS of 0.809 nm) if the directions of cutting and MRF polishing are along the (110) direction.

Anthropogenic Organic Compounds in Source and Finished Groundwater of Community Water Systems in the Piedmont Physiographic Province, Potomac River Basin, Maryland and Virginia, 2003-04

USGS Publications Warehouse

Banks, William S.L.; Reyes, Betzaida

2009-01-01

A source- and finished-water-quality assessment of groundwater was conducted in the Piedmont Physiographic Province of Maryland and Virginia in the Potomac River Basin during 2003-04 as part of the U.S. Geological Survey's National Water-Quality Assessment Program. This assessment used a two-phased approach to sampling that allowed investigators to evaluate the occurrence of more than 280 anthropogenic organic compounds (volatile organic compounds, pesticides and pesticide degradates, and other anthropogenic organic compounds). Analysis of waters from 15 of the largest community water systems in the study area were included in the assessment. Source-water samples (raw-water samples collected prior to treatment) were collected at the well head. Finished-water samples (raw water that had been treated and disinfected) were collected after treatment and prior to distribution. Phase one samples, collected in August and September 2003, focused on source water. Phase two analyzed both source and finished water, and samples were collected in August and October of 2004. The results from phase one showed that samples collected from the source water for 15 community water systems contained 92 anthropogenic organic compounds (41 volatile organic compounds, 37 pesticides and pesticide degradates, and 14 other anthropogenic organic compounds). The 5 most frequently occurring anthropogenic organic compounds were detected in 11 of the 15 source-water samples. Deethylatrazine, a degradate of atrazine, was present in all 15 samples and metolachlor ethanesulfonic acid, a degradate of metolachlor, and chloroform were present in 13 samples. Atrazine and metolachlor were present in 12 and 11 samples, respectively. All samples contained a mixture of compounds with an average of about 14 compounds per sample. Phase two sampling focused on 10 of the 15 community water systems that were selected for resampling on the basis of occurrence of anthropogenic organic compounds detected most

Anthropogenic Organic Compounds in Source and Finished Water from Community Water System Wells in Western and Central Connecticut, 2002-2004

USGS Publications Warehouse

Trombley, Thoams J.; Brown, Craig J.; Delzer, Gregory C.

2007-01-01

A water-quality assessment by the U.S. Geological Survey (USGS) determined the occurrence of anthropogenic (manmade) organic compounds (AOCs) in water from 15 community water system (CWS) wells and associated finished drinking water. The study, which focused on water from the unconfined glacial stratified aquifer in western and central Connecticut, was conducted as part of the USGS National Water-Quality Assessment Program (NAWQA) Source Water-Quality Assessment (SWQA) project and included analysis of water samples for 88 volatile organic compounds (VOCs), 120 pesticides, and 50 other anthropogenic organic compounds (OAOCs). During Phase I of the study, 25 AOCs were detected (12 VOCs, 10 pesticides, and 3 OAOCs) in source-water samples collected from 15 CWS wells sampled once from October 2002 to May 2003. Although concentrations generally were low (less than 1 microgram per liter), four compounds were detected at higher concentrations in ground water from four wells. The most frequently occurring AOCs were detected in more than half of the samples and included chloroform (87 percent), methyl tert-butyl ether (MTBE, 80 percent), 1,1,1-trichloroethane (67 percent), atrazine (60 percent), deethylatrazine (60 percent), perchloroethene (PCE, 53 percent), and simazine (53 percent). Trichloroethene (TCE) was detected in 47 percent of samples. Samples generally contained a mixture of compounds ranging from 2 to 19 detected compounds, with an average of 8 detected compounds per sample. During Phase II of the study, 42 AOCs were detected in source-water samples collected from 10 resampled CWS wells or their associated finished water. Trihalomethanes accounted for most of the VOCs detections with all concentrations less than 1 microgram per liter. Chloroform, the most frequently detected VOC, was found in all source-water and all finished-water samples. As with the Phase I samples, other frequently detected VOCs included MTBE, and the solvents 1,1,1-trichloroethane, PCE, and

Are all metal-on-metal hip revision operations contributing to the National Joint Registry implant survival curves? : a study comparing the London Implant Retrieval Centre and National Joint Registry datasets.

PubMed

Sabah, S A; Henckel, J; Koutsouris, S; Rajani, R; Hothi, H; Skinner, J A; Hart, A J

2016-01-01

The National Joint Registry for England, Wales and Northern Ireland (NJR) has extended its scope to report on hospital, surgeon and implant performance. Data linkage of the NJR to the London Implant Retrieval Centre (LIRC) has previously evaluated data quality for hip primary procedures, but did not assess revision records. We analysed metal-on-metal hip revision procedures performed between 2003 and 2013. A total of 69 929 revision procedures from the NJR and 929 revised pairs of components from the LIRC were included. We were able to link 716 (77.1%) revision procedures on the NJR to the LIRC. This meant that 213 (22.9%) revision procedures at the LIRC could not be identified on the NJR. We found that 349 (37.6%) explants at the LIRC completed the full linkage process to both NJR primary and revision databases. Data completion was excellent (> 99.9%) for revision procedures reported to the NJR. This study has shown that only approximately one third of retrieved components at the LIRC, contributed to survival curves on the NJR. We recommend prospective registry-retrieval linkage as a tool to feedback missing and erroneous data to the NJR and improve data quality. Prospective Registry - retrieval linkage is a simple tool to evaluate and improve data quality on the NJR. ©2016 Sabah et al.

Factors associated with the serological prevalence of Salmonella enterica in Greek finishing swineherds.

PubMed Central

Leontides, L. S.; Grafanakis, E.; Genigeorgis, C.

2003-01-01

Blood samples were taken from 50 finishing pigs at 90-105 kg in each of 59 randomly selected farrow-to-finish herds. The sera were tested for antibodies to Salmonella enterica by the Danish mix-ELISA. Samples with an optical density of > 10% were considered to be positive. Associations between the odds of seropositivity of pigs and possible risk factors were evaluated in multivariable logistic regression models. The results of the analysis indicated that pigs fed non-pelleted dry or wet ration had 11 (P = 0.0004) or 9 (P = 0.02) times, respectively, lower odds of seropositivity than those fed pelleted ration. The risk of seropositivity was 4 (P = 0.0006) times higher in pigs fed a combination of chlortetracycline, procaine penicillin and sulphamethazine during fattening than in those fed an approved growth promotor or a probiotic. PMID:12948357

Clean thermal decomposition of tertiary-alkyl metal thiolates to metal sulfides: environmentally-benign, non-polar inks for solution-processed chalcopyrite solar cells.

PubMed

Heo, Jungwoo; Kim, Gi-Hwan; Jeong, Jaeki; Yoon, Yung Jin; Seo, Jung Hwa; Walker, Bright; Kim, Jin Young

2016-11-09

We report the preparation of Cu 2 S, In 2 S 3 , CuInS 2 and Cu(In,Ga)S 2 semiconducting films via the spin coating and annealing of soluble tertiary-alkyl thiolate complexes. The thiolate compounds are readily prepared via the reaction of metal bases and tertiary-alkyl thiols. The thiolate complexes are soluble in common organic solvents and can be solution processed by spin coating to yield thin films. Upon thermal annealing in the range of 200-400 °C, the tertiary-alkyl thiolates decompose cleanly to yield volatile dialkyl sulfides and metal sulfide films which are free of organic residue. Analysis of the reaction byproducts strongly suggests that the decomposition proceeds via an SN 1 mechanism. The composition of the films can be controlled by adjusting the amount of each metal thiolate used in the precursor solution yielding bandgaps in the range of 1.2 to 3.3 eV. The films form functioning p-n junctions when deposited in contact with CdS films prepared by the same method. Functioning solar cells are observed when such p-n junctions are prepared on transparent conducting substrates and finished by depositing electrodes with appropriate work functions. This method enables the fabrication of metal chalcogenide films on a large scale via a simple and chemically clear process.

Clean thermal decomposition of tertiary-alkyl metal thiolates to metal sulfides: environmentally-benign, non-polar inks for solution-processed chalcopyrite solar cells

NASA Astrophysics Data System (ADS)

Heo, Jungwoo; Kim, Gi-Hwan; Jeong, Jaeki; Yoon, Yung Jin; Seo, Jung Hwa; Walker, Bright; Kim, Jin Young

2016-11-01

We report the preparation of Cu2S, In2S3, CuInS2 and Cu(In,Ga)S2 semiconducting films via the spin coating and annealing of soluble tertiary-alkyl thiolate complexes. The thiolate compounds are readily prepared via the reaction of metal bases and tertiary-alkyl thiols. The thiolate complexes are soluble in common organic solvents and can be solution processed by spin coating to yield thin films. Upon thermal annealing in the range of 200-400 °C, the tertiary-alkyl thiolates decompose cleanly to yield volatile dialkyl sulfides and metal sulfide films which are free of organic residue. Analysis of the reaction byproducts strongly suggests that the decomposition proceeds via an SN1 mechanism. The composition of the films can be controlled by adjusting the amount of each metal thiolate used in the precursor solution yielding bandgaps in the range of 1.2 to 3.3 eV. The films form functioning p-n junctions when deposited in contact with CdS films prepared by the same method. Functioning solar cells are observed when such p-n junctions are prepared on transparent conducting substrates and finished by depositing electrodes with appropriate work functions. This method enables the fabrication of metal chalcogenide films on a large scale via a simple and chemically clear process.

Water-flow variation and pharmacoepidemiology of tetracycline hydrochloride administration via drinking water in swine finishing farms.

PubMed

Dorr, Paul M; Nemechek, Megan S; Scheidt, Alan B; Baynes, Ronald E; Gebreyes, Wondwossen A; Almond, Glen W

2009-08-01

To evaluate variation of drinking-water flow rates in swine finishing barns and the relationship between drinker flow rate and plasma tetracycline concentrations in pigs housed in different pens. Cross-sectional (phase 1) and cohort (phase 2) studies. 13 swine finishing farms (100 barns with 7,122 drinkers) in phase 1 and 100 finishing-stage pigs on 2 finishing farms (1 barn/farm) in phase 2. In phase 1, farms were evaluated for water-flow variation, taking into account the following variables: position of drinkers within the barn, type of drinker (swing or mounted), pig medication status, existence of designated sick pen, and existence of leakage from the waterline. In phase 2, blood samples were collected from 50 pigs/barn (40 healthy and 10 sick pigs) in 2 farms at 0, 4, 8, 24, 48, and 72 hours after initiation of water-administered tetracycline HCl (estimated dosage, 22 mg/kg [10 mg/lb]). Plasma tetracycline concentrations were measured via ultraperformance liquid chromatography. Mean farm drinker flow rates ranged from 1.44 to 2.77 L/min. Significant differences in flow rates existed according to drinker type and whether tetracycline was included in the water. Mean drinker flow rates and plasma tetracycline concentrations were significantly different between the 2 farms but were not different between healthy and sick pigs. The plasma tetracycline concentrations were typically < 0.3 microg/mL. Many factors affected drinker flow rates and therefore the amount of medication pigs might have received. Medication of pigs with tetracycline through water as performed in this study had questionable therapeutic value.

Tribological investigation of a functional medical textile with lubricating drug-delivery finishing.

PubMed

Gerhardt, L-C; Lottenbach, R; Rossi, R M; Derler, S

2013-08-01

Textile-based drug delivery systems have a high potential for innovative medical and gerontechnological applications. In this study, the tribological behaviour and lubrication properties of a novel textile with drug delivery function/finishing was investigated by means of friction experiments that simulated cyclic dynamic contacts with skin under dry and wet conditions. The textile drug delivery system is based on a loadable biopolymer dressing on a polyester (PES) woven fabric. The fabrics were finished with low (LC) and highly cross-linked (HC) polysaccharide dressings and investigated in the unloaded condition as well as loaded with phytotherapeutic substances. The mechanical resistance and possible abrasion of the functional coatings on the textile substrate were assessed by friction measurements and scanning electron microscopical analyses. Under dry contact conditions, all investigated fabrics (PES substrate alone and textiles with loaded and unloaded dressings) showed generally low friction coefficients (0.20-0.26). Under wet conditions, the measured friction coefficients were typically higher (0.34-0.51) by a factor of 1.5-2. In the wet condition, both loaded drug delivery textiles exhibited 7-29% lower friction (0.34-0.41) than the PES fabric with unloaded dressings (0.42-0.51), indicating pronounced lubrication effects. The lubrication effects as well as the abrasion resistance of the studied textiles with drug delivery function depended on the degree of dilution of the phytotherapeutic substances. Lubricating formulations of textile-based drug delivery systems which reduce friction against the skin might be promising candidates for advanced medical textile finishes in connection with skin care and wound (decubitus ulcer) prevention. Copyright © 2013 Elsevier B.V. All rights reserved.

Nanoindentation hardness of particles used in magnetorheological finishing (MRF).

PubMed

Shorey, A B; Kwong, K M; Johnson, K M; Jacobs, S D

2000-10-01

Knowledge of the hardness of abrasive particles that are used in polishing is a key to the fundamental understanding of the mechanisms of material removal. The magnetorheological-finishing process uses both magnetic and nonmagnetic abrasive particles during polishing. The nanohardnesses of the micrometer-sized magnetic carbonyl iron and nonmagnetic abrasive particles have been measured successfully by use of novel, to our knowledge, sample-preparation and nanoindentation techniques. Some of the results reported compare favorably with existing microhardness data found in the literature, whereas other results are new.

The Prevalence of CKD in Rural Canadian Indigenous Peoples: Results From the First Nations Community Based Screening to Improve Kidney Health and Prevent Dialysis (FINISHED) Screen, Triage, and Treat Program.

PubMed

Komenda, Paul; Lavallee, Barry; Ferguson, Thomas W; Tangri, Navdeep; Chartrand, Caroline; McLeod, Lorraine; Gordon, Audrey; Dart, Allison; Rigatto, Claudio

2016-10-01

Indigenous Canadians have high rates of risk factors for chronic kidney disease (CKD), in particular diabetes. Furthermore, they have increased rates of complications associated with CKD, such as kidney failure and vascular disease. Our objective was to describe the prevalence of CKD in this population. Cross-sectional cohort. Indigenous (First Nations) Canadians 18 years or older screened as part of the First Nations Community Based Screening to Improve Kidney Health and Prevent Dialysis (FINISHED) project, an initiative completed in 2015 that accomplished community-wide screening in 11 rural communities in Manitoba, Canada. Indigenous ethnicity and geographic location (communities accessible by road compared with those accessible only by air). Prevalence of CKD, presumed based on a single ascertainment of urine albumin-creatinine ratio (UACR) ≥ 30mg/g and/or estimated glomerular filtration rate (eGFR)<60mL/min/1.73m(2). Kidney function measured by eGFR (CKD-EPI creatinine equation) and UACR. 1,346 adults were screened; 25.5% had CKD, defined as UACR≥30mg/g or eGFR<60mL/min/1.73m(2). Communities accessible by road had a lower prevalence of CKD (17.6%) than more remote communities accessible only by air (34.4%). Of those screened, 3.3% had reduced kidney function (defined as eGFR<60mL/min/1.73m(2)). Severely increased albuminuria was present in 5.0% of those screened. Presumption of chronicity based on a single ascertainment. There is a possibility of sampling bias, the net direction of which is uncertain. We found a 2-fold higher prevalence of CKD in indigenous Canadians in comparison to the general population and a prevalence of severely increased albuminuria that was 5-fold higher. This is comparable to patients with diabetes and/or hypertension. Public health strategies to screen, triage, and treat all Canadian indigenous peoples with CKD should be considered. Copyright © 2016 National Kidney Foundation, Inc. Published by Elsevier Inc. All rights reserved.