Science.gov

Sample records for overview die entzuendliche

  1. Die Attachment for -120 C to +20 C Thermal Cycling of Microelectronics for Future Mars Rovers: An Overview

    NASA Technical Reports Server (NTRS)

    Kirschman, Randall K.; Sokolowski, Witold M.; Kolawa, Elizabeth A.

    1999-01-01

    Active thermal control for electronics on Mars Rovers imposes a serious penalty in weight, volume, power consumption, and reliability. Thus, we propose that thermal control be eliminated for future Rovers. From a functional standpoint there is no reason that the electronics could not operate over the entire temperature range of the Martian environment, which can vary from a low of approximately equal -90 C to a high of approximately equal +20 C during the Martian night and day. The upper end of this range is well within that for conventional electronics. Although the lower end is considerably below that for which conventional--even high-reliability electronics is designed or tested, it is well established that electronic devices can operate to such low temperatures. The primary concern is reliability of the overall electronic system, especially in regard to the numerous daily temperature cycles that it would experience over the duration of a mission on Mars. Accordingly, key reliability issues have been identified for elimination of thermal control on future Mars Rovers. One of these is attachment of semiconductor die onto substrates and into packages. Die attachment is critical since it forms a mechanical, thermal and electrical interface between the electronic device and the substrate or package. This paper summarizes our initial investigation of existing information related to this issue, in order to form an opinion whether die attachment techniques exist, or could be developed with reasonable effort, to withstand the Mars thermal environment for a mission duration of approximately I year. Our conclusion, from a review of literature and personal contacts. is that die attachment can be made sufficiently reliable to satisfy the requirements of future Mars Rovers. Moreover, it appears that there are several possible techniques from which to choose and that the requirements could be met by judicious selection from existing methods using hard solders, soft solders

  2. Overview.

    ERIC Educational Resources Information Center

    Kain, Craig D.; And Others

    This document consists of the first section of a book written to educate and inform those in the helping professions on how to deal with Acquired Immune Deficiency Syndrome (AIDS). The two chapters in this first section present an overview of the AIDS crisis and provide a foundation for the rest of the book. "Emerging Trends: AIDS Today and in the…

  3. When a Baby Dies.

    ERIC Educational Resources Information Center

    Church, Martha Jo; And Others

    Written especially for grieving mothers whose babies have died, this booklet offers an overview of stages and experiences through which bereaved parents commonly pass. Specifically, the text is intended to give comfort to bereaved parents, offer insight into the grieving process, and provide thoughts on leave-taking ceremonies. The first section…

  4. SPHERICAL DIE

    DOEpatents

    Livingston, J.P.

    1959-01-27

    A die is presented for pressing powdered materials into a hemispherical shape of uniforin density and wall thickness comprising a fcmale and male die element held in a stationary spaced relation with the space being equivalent to the wall thickness and defining the hemispherical shape, a pressing ring linearly moveable along the male die element, an inlet to fill the space with powdered materials, a guiding system for moving the pressing ring along the male die element so as to press the powdered material and a heating system for heating the male element so that the powdered material is heated while being pressed.

  5. Sputtered protective coatings for die casting dies

    NASA Technical Reports Server (NTRS)

    Mirtich, M. J.; Nieh, C. Y.; Wallace, J. F.

    1981-01-01

    This investigation determined whether selected ion beam sputtered coatings on H-13 die steel would have the potential of improving the thermal fatigue behavior of the steel used as a die in aluminum die casting. The coatings were selected to test candidate insulators and metals capable of providing protection of the die surface. The studies indicate that 1 micrometer thick W and Pt coatings reduced the thermal fatigue more than any other coating tested and are candidates to be used on a die surface to increase die life.

  6. Wege in die Zukunft

    NASA Astrophysics Data System (ADS)

    Kauermann, Göran; Mosler, Karl

    Die Zukunft stellt große Herausforderungen an die Arbeit der Deutschen Statistischen Gesellschaft. Sie betreffen die gestiegenen Anforderungen der Nutzer von Statistik, die Kommunikationsmöglichkeiten des Internets sowie die Dynamik der statistischen Wissenschaften und ihrer Anwendungsgebiete. Das Kapitel 5 beschreibt, wie sich die Gesellschaft diesen Herausforderungen stellt und welche Ziele sie sich in der wissenschaftlichen Zusammenarbeit und im Kampf gegen das Innumeratentum gesetzt hat.

  7. Die drool and die drool theory

    NASA Astrophysics Data System (ADS)

    Schmalzer, A. M.; Giacomin, A. Jeffrey

    2013-04-01

    When molten plastic is extruded from a die, it sometimes collects on the open face of the die. Known as die drool, this phenomenon costs plastics manufacturers by requiring die cleaning. This has been attributed to many causes, but none of these has led to an equation for the drool rate. In this work we provide an exact analytical solution for the drool rate, and we base this solution on a postulate of a cohesive slip layer near the die walls. We thus attribute die drool to cohesive failure within the fluid at an internal surface where the fluid slips on itself. We adimensionalize the drool rate with the production rate, and call this the build up ratio, BR. We provide an exact analytical solution for BR when the cohesive slip layer either sticks at the wall. We examine the slit geometry corresponding to sheet or film extrusion.

  8. Packaged die heater

    SciTech Connect

    Spielberger, Richard; Ohme, Bruce Walker; Jensen, Ronald J.

    2011-06-21

    A heater for heating packaged die for burn-in and heat testing is described. The heater may be a ceramic-type heater with a metal filament. The heater may be incorporated into the integrated circuit package as an additional ceramic layer of the package, or may be an external heater placed in contact with the package to heat the die. Many different types of integrated circuit packages may be accommodated. The method provides increased energy efficiency for heating the die while reducing temperature stresses on testing equipment. The method allows the use of multiple heaters to heat die to different temperatures. Faulty die may be heated to weaken die attach material to facilitate removal of the die. The heater filament or a separate temperature thermistor located in the package may be used to accurately measure die temperature.

  9. Displaced capillary dies

    DOEpatents

    Kalejs, Juris P.; Chalmers, Bruce; Surek, Thomas

    1984-01-01

    An asymmetrical shaped capillary die made exclusively of graphite is used to grow silicon ribbon which is capable of being made into solar cells that are more efficient than cells produced from ribbon made using a symmetrically shaped die.

  10. Displaced capillary dies

    DOEpatents

    Kalejs, Juris P.; Chalmers, Bruce; Surek, Thomas

    1982-01-01

    An asymmetrical shaped capillary die made exclusively of graphite is used to grow silicon ribbon which is capable of being made into solar cells that are more efficient than cells produced from ribbon made using a symmetrically shaped die.

  11. HIGH PRESSURE DIES

    DOEpatents

    Wilson, W.B.

    1960-05-31

    A press was invented for subjecting specimens of bismuth, urania, yttria, or thoria to high pressures and temperatures. The press comprises die parts enclosing a space in which is placed an electric heater thermally insulated from the die parts so as not to damage them by heat. The die parts comprise two opposed inner frustoconical parts and an outer part having a double frustoconical recess receiving the inner parts. The die space decreases in size as the inner die parts move toward one another against the outer part and the inner parts, though very hard, do not fracture because of the mode of support provided by the outer part.

  12. Die singulation method

    SciTech Connect

    Swiler, Thomas P; Garcia, Ernest J; Francis, Kathryn M

    2014-01-07

    A method is disclosed for singulating die from a semiconductor substrate (e.g. a semiconductor-on-insulator substrate or a bulk silicon substrate) containing an oxide layer (e.g. silicon dioxide or a silicate glass) and one or more semiconductor layers (e.g. monocrystalline or polycrystalline silicon) located above the oxide layer. The method etches trenches through the substrate and through each semiconductor layer about the die being singulated, with the trenches being offset from each other around at least a part of the die so that the oxide layer between the trenches holds the substrate and die together. The trenches can be anisotropically etched using a Deep Reactive Ion Etching (DRIE) process. After the trenches are etched, the oxide layer between the trenches can be etched away with a HF etchant to singulate the die. A release fixture can be located near one side of the substrate to receive the singulated die.

  13. Die singulation method

    SciTech Connect

    Swiler, Thomas P.; Garcia, Ernest J.; Francis, Kathryn M.

    2013-06-11

    A method is disclosed for singulating die from a semiconductor substrate (e.g. a semiconductor-on-insulator substrate or a bulk silicon substrate) containing an oxide layer (e.g. silicon dioxide or a silicate glass) and one or more semiconductor layers (e.g. monocrystalline or polycrystalline silicon) located above the oxide layer. The method etches trenches through the substrate and through each semiconductor layer about the die being singulated, with the trenches being offset from each other around at least a part of the die so that the oxide layer between the trenches holds the substrate and die together. The trenches can be anisotropically etched using a Deep Reactive Ion Etching (DRIE) process. After the trenches are etched, the oxide layer between the trenches can be etched away with an HF etchant to singulate the die. A release fixture can be located near one side of the substrate to receive the singulated die.

  14. Extrusion die and method

    DOEpatents

    Lipp, G. Daniel

    1994-04-26

    A method and die apparatus for manufacturing a honeycomb body of rhombic cell cross-section by extrusion through an extrusion die of triangular cell discharge slot configuration, the die incorporating feedholes at selected slot intersections only, such that slot segments communicating directly with the feedholes discharge web material and slot segments not so connected do not discharge web material, whereby a rhombic cell cross-section in the extruded body is provided.

  15. The Ambiguous Dying Syndrome

    ERIC Educational Resources Information Center

    Bern-Klug, Mercedes

    2004-01-01

    More than one-half of the 2.4 million deaths that will occur in the United States in 2004 will be immediately preceded by a time in which the likelihood of dying can best be described as "ambiguous." Many people die without ever being considered "dying" or "at the end of life." These people may miss out on the opportunity to close important…

  16. Sputtered protective coatings for die casting dies

    NASA Technical Reports Server (NTRS)

    Mirtich, M. J.; Nieh, C.-Y.; Wallace, J. F.

    1981-01-01

    Three experimental research designs investigating candidate materials and processes involved in protective die surface coating procedures by sputter deposition, using ion beam technologies, are discussed. Various pre-test results show that none of the coatings remained completely intact for 15,000 test cycles. The longest lifetime was observed for coatings such as tungsten, platinum, and molybdenum which reduced thermal fatigue, but exhibited oxidation and suppressed crack initiation only as long as the coating did not fracture. Final test results confirmed earlier findings and coatings with Pt and W proved to be the candidate materials to be used on a die surface to increase die life. In the W-coated specimens, which remained intact on the surface after thermal fatigue testing, no oxidation was found under the coating, although a few cracks formed on the surface where the coating broke down. Further research is planned.

  17. Die Soldering in Aluminium Die Casting

    SciTech Connect

    Han, Q.; Kenik, E.A.; Viswanathan, S.

    2000-03-15

    Two types of tests, dipping tests and dip-coating tests were carried out on small steel cylinders using pure aluminum and 380 alloy to investigate the mechanism of die soldering during aluminum die casting. Optical and scanning electron microscopy were used to study the morphology and composition of the phases formed during soldering. A soldering mechanism is postulated based on experimental observations. A soldering critical temperature is postulated at which iron begins to react with aluminum to form an aluminum-rich liquid phase and solid intermetallic compounds. When the temperature at the die surface is higher than this critical temperature, the aluminum-rich phase is liquid and joins the die with the casting during the subsequent solidification. The paper discusses the mechanism of soldering for the case of pure aluminum and 380 alloy casting in a steel mold, the factors that promote soldering, and the strength of the bond formed when soldering occurs. conditions, an aluminum-rich soldering layer may also form over the intermetallic layer. Although a significant amount of research has been conducted on the nature of these intermetallics, little is known about the conditions under which soldering occurs.

  18. Is Dying Young Worse than Dying Old?

    ERIC Educational Resources Information Center

    Jecker, Nancy S.; Schneiderman, Lawrence J.

    1994-01-01

    Notes that, in contemporary Western society, people feel death of small child is greater injustice than death of older adult and experience correspondingly greater sorrow, anger, regret, or bitterness when very young person dies. Contrasts these attitudes with those of ancient Greece and shows relevance that different attitudes toward death have…

  19. Micromechanical die attachment surcharge

    DOEpatents

    Filter, William F.; Hohimer, John P.

    2002-01-01

    An attachment structure is disclosed for attaching a die to a supporting substrate without the use of adhesives or solder. The attachment structure, which can be formed by micromachining, functions purely mechanically in utilizing a plurality of shaped pillars (e.g. round, square or polygonal and solid, hollow or slotted) that are formed on one of the die or supporting substrate and which can be urged into contact with various types of mating structures including other pillars, a deformable layer or a plurality of receptacles that are formed on the other of the die or supporting substrate, thereby forming a friction bond that holds the die to the supporting substrate. The attachment structure can further include an alignment structure for precise positioning of the die and supporting substrate to facilitate mounting the die to the supporting substrate. The attachment structure has applications for mounting semiconductor die containing a microelectromechanical (MEM) device, a microsensor or an integrated circuit (IC), and can be used to form a multichip module. The attachment structure is particularly useful for mounting die containing released MEM devices since these devices are fragile and can otherwise be damaged or degraded by adhesive or solder mounting.

  20. Extrusion die and method

    DOEpatents

    Lipp, G. Daniel

    1994-05-03

    A method and die apparatus for manufacturing a honeycomb body of triangular cell cross-section and high cell density, the die having a combination of (i) feedholes feeding slot intersections and (ii) feedholes feeding slot segments not supplied from slot intersections, whereby a reduction in feedhole count is achieved while still retaining good extrusion efficiency and extrudate uniformity.

  1. Die zwei Kulturen

    NASA Astrophysics Data System (ADS)

    Ankolekar, Anupriya; Krötzsch, Markus; Tran, Than; Vrandecic, Denny

    Oft werden zwei mögliche Entwicklungen des Webs diskutiert - das Web 2.0 und das Semantic Web. Wenn wir diese zwei Visionen für das zukünftige Web unter die Lupe nehmen, dann lässt sich feststellen, dass sich die Ideen in ihrem Kern und ihren Technologien gegenseitig ergänzen. Dementsprechend können und sollen beide Visionen von den Erfahrungen und Stärken der anderen profitieren. Wir glauben daran, dass zukünftige Webanwendungen den Web 2.0-Fokus auf Community und Benutzerfreundlichkeit beibehalten und, darüber hinaus, auch von Technologien des Semantic Web zur Vereinfachung der mashupähnlichen Datenintegration profitieren werden. Auf Basis eines Semantic Blog-Szenarios werden wir hier die Vorteile einer möglichen Kombination von Semantic Web und Web 2.0 illustrieren, die zeitnah realisiert werden kann. Wir werden auch auf technische Probleme eingehen, die bei der Erweiterung dieses Szenarios entstehen. Wir stellen dar, wie aktuelle Entwicklungen in der Semantic Web Forschung diese Probleme angehen können, und setzen zugleich auch Schwerpunkte für die zukünftige Forschung, die in diesem Zusammenhang relevant sind.

  2. Die Zeitung der Zukunft

    NASA Astrophysics Data System (ADS)

    Wieser, Christoph; Schaffert, Sebastian

    Schon lange wird spekuliert, wie wir in Zukunft Zeitung lesen werden. Werden wir am Frühstückstisch wie gewohnt in einer Zeitung aus Papier schmökern oder werden wir die Zeitung als biegsame Folie beschrieben mit elektronischer Tinte in Händen halten? Wird die Zeitung mit anderen Medien wie Radio und Fernsehen verschmelzen? Viele Varianten sind denkbar. Heute lässt sich schon ein Trend ablesen: Immer mehr Leser entdecken die Online-Zeitung als Informationsmedium, eine Voraussetzung für die Nutzung neuer Technologien in der Zeitung der Zukunft. In diesem Kapitel stellen wir Entwicklungsmöglichkeiten der Online-Zeitung dar, wie sie im Social Semantic Web möglich werden.

  3. When Somebody Dies

    MedlinePlus

    ... alguien muere All living things — including bugs and fish and people — die. It's difficult, even for grownups, ... kind of death for families and friends to deal with because it happens so fast. There is ...

  4. Dying in the age of choice.

    PubMed

    Black, Kathy; Csikai, Ellen L

    2015-01-01

    Due to the unprecedented increase in the United States aging demographics, many more people are living longer and reaching older ages than ever before. However, a longer life is not necessarily a better life, as the vast majority will face a period of prolonged deteriorating health prior to death. Although notable efforts have been underway that are designed to improve the end-of-life experience, increasing numbers of individuals express a desire and/or act upon an intent to end their lives precipitously. Though still limited, the options to actively participate in their own deaths are growing. Requests for a hastened death can occur among people of all ages and includes those with advanced illness as well as others wanting to die due to unbearable suffering. This article provides an overview of the ongoing discourse about the experience of dying faced by many older adults, including aspects frequently associated with "a good death." The limitations of established practices which seek to provide a "better" dying experience are identified followed by discussion of the growing availability of alternative options. Reflective considerations are presented to guide practice vis-à-vis the changing landscape surrounding options in dying. PMID:25869146

  5. Issues with dying patients.

    PubMed

    Valent, P

    1978-04-22

    Doctors have the privilege of looking after patients from the moment of birth to the moment of death. Yet, the holistic approach to patients is interfered with by the doctor's role as a warrior against death, where death's everpresent claim on our lives, and its final victory, are ignored. This paper attempts to explore why doctors are in their current position, the mechanisms for ignoring death which are shared by doctors and patients, the nature of the fear of death, and practical implications for the treatment of dying patients. More and more patients die now in medical settings. It is incumbent on doctors to understand the dying process, if much unnecessary suffering is to be prevented. PMID:661717

  6. Experiences of the dying.

    PubMed

    Schoenbeck, Susan L

    2011-01-01

    It is often a mystery to us how we have come to know and believe in certain things. Beliefs are like guests who come up to a door. They come in only if the host opens it and invites them in. Otherwise they are turned away, unable to enter. LPNs/LVNs are invited to reflect on their experiences and expand their knowledge and beliefs. There is growing recognition that bedside talks of the dying, spirit travel and near-death events are real events for the people who experience them. LPNs/ LVNs are encouraged to expand their knowledge and beliefs about dying. PMID:23252027

  7. Assisted Dying in Canada.

    PubMed

    Schuklenk, Udo

    2014-01-01

    This paper makes an affirmative ethical case in favour of the decriminalization of assisted dying in Canada. It then proceeds to defending the affirmative case against various slippery-slope arguments that are typically deployed by opponents of assisted dying. Finally, a recent case of questionable professional conduct by anti-euthanasia campaigners cum academics is flagged as a warning to all of us not to permit the quality of the professional debate to deteriorate unacceptably, despite the personal emotional investments involved on all sides of the debate. PMID:26871530

  8. Poetry and the Dying.

    ERIC Educational Resources Information Center

    Kramer, Aaron

    1992-01-01

    Demonstrates roles poetry can play as people confront the death of loved ones and their own dying. Gives examples of Heinrich Heine transforming his agony into art and, from the poetry of two college students, both in advanced stages of neurological disease, which was read aloud in class, teaching all present something about how to approach their…

  9. Tool & Die Technician.

    ERIC Educational Resources Information Center

    Ohio State Univ., Columbus. Center on Education and Training for Employment.

    This document contains 23 units to consider for use in a tech prep competency profile for the occupation of tool and die technician. All the units listed will not necessarily apply to every situation or tech prep consortium, nor will all the competencies within each unit be appropriate. Several units appear within each specific occupation and…

  10. Navigating "Assisted Dying".

    PubMed

    Schipper, Harvey

    2016-02-01

    Carter is a bellwether decision, an adjudication on a narrow point of law whose implications are vast across society, and whose impact may not be realized for years. Coupled with Quebec's Act Respecting End-of-life Care it has sharply changed the legal landscape with respect to actively ending a person's life. "Medically assisted dying" will be permitted under circumstances, and through processes, which have yet to be operationally defined. This decision carries with it moral assumptions, which mean that it will be difficult to reach a unifying consensus. For some, the decision and Act reflect a modern acknowledgement of individual autonomy. For others, allowing such acts is morally unspeakable. Having opened the Pandora's Box, the question becomes one of navigating a tolerable societal path. I believe it is possible to achieve a workable solution based on the core principle that "medically assisted dying" should be a very rarely employed last option, subject to transparent ongoing review, specifically as to why it was deemed necessary. My analysis is based on 1. The societal conditions in which have fostered demand for "assisted dying", 2. Actions in other jurisdictions, 3. Carter and Quebec Bill 52, 4. Political considerations, 5. Current medical practice. Leading to a series of recommendations regarding. 1. Legislation and regulation, 2. The role of professional regulatory agencies, 3. Medical professions education and practice, 4. Public education, 5. Health care delivery and palliative care. Given the burden of public opinion, and the legal steps already taken, a process for assisted-dying is required. However, those legal and regulatory steps should only be considered a necessary and defensive first step in a two stage process. The larger goal, the second step, is to drive the improvement of care, and thus minimize assisted-dying. PMID:27169205

  11. Herausforderungen durch die deutsche Wiedervereinigung

    NASA Astrophysics Data System (ADS)

    Stäglin, Reiner

    Die Wiedervereinigung stellte auch die Statistik vor große Aufgaben. Die als Organ der staatlichen Planung staatsnah orientierte Statistik der DDR musste auf das zur Neutralität und wissenschaftlichen Unabhängigkeit verpflichtete System der Bundesrepublik umgestellt werden. Ebenso verlangten die Universitäten eine Neuorientierung. Die Deutsche Statistische Gesellschaft hat sich vor allem dreier Aufgaben mit großem Engagement, aber auch mit Bedachtsamkeit angenommen: Aufnahme und Integration der Statistiker aus den neuen Bundesländern in die Gesellschaft, Begleitung der Neuausrichtung des Faches Statistik an deren Hochschulen und Sicherung sowie Nutzung von Datenbeständen der ehemaligen DDR.

  12. Modeling the Mechanical Performance of Die Casting Dies

    SciTech Connect

    R. Allen Miller

    2004-02-27

    The following report covers work performed at Ohio State on modeling the mechanical performance of dies. The focus of the project was development and particularly verification of finite element techniques used to model and predict displacements and stresses in die casting dies. The work entails a major case study performed with and industrial partner on a production die and laboratory experiments performed at Ohio State.

  13. Heated die facilitates tungsten forming

    NASA Technical Reports Server (NTRS)

    Chattin, J. H.; Haystrick, J. E.; Laughlin, J. C.; Leidy, R. A.

    1966-01-01

    Tungsten forming in a press brake employs a bottom die assembly with a heating manifold between two water-cooled die sections. The manifold has hydrogen-oxygen burners spaced along its length for even heat during forming.

  14. Psychotherapy with Older Dying Persons.

    ERIC Educational Resources Information Center

    Dye, Carol J.

    Psychotherapy with older dying patients can lead to problems of countertransference for the clinician. Working with dying patients requires flexibility to adapt basic therapeutics to the institutional setting. Goals of psychotherapy must be reconceptualized for dying clients. The problems of countertransference arise because clinicians themselves…

  15. EPICS overview

    SciTech Connect

    1996-02-01

    This overview describes basic attributes, hardware, IOC software platforms, database access and scanning, record support, database monitors, channel access, client services, search server, connection management, OPI tools, and core software of the EPICS system.

  16. Nitriding of Aluminum Extrusion Die: Effect of Die Geometry

    NASA Astrophysics Data System (ADS)

    Akhtar, S. S.; Arif, A. F. M.; Yilbas, B. S.

    2010-04-01

    Nitriding of complex-shaped extrusion dies may result in non-uniform nitride layers and hence a required hardness may not be achieved in some regions of the bearing area. The present study is carried out to assess the effect of extrusion die profile on the characteristics and growth behavior of nitride layers so that the critical die design feature can be identified to enhance the uniformity of the nitride layer. For this purpose, AISI H13 steel samples have been manufactured with profiles similar to those of hot extrusion dies. The samples were then gas nitrided under controlled nitriding potential. The uniformity and depth of nitride layers have been investigated in terms of compound layer and total nitride case depth for selected die features. The results of this study indicated the need to include the effect of profile on the nitride layer for the optimal die design with improved service life.

  17. Accurate defect die placement and nuisance defect reduction for reticle die-to-die inspections

    NASA Astrophysics Data System (ADS)

    Wen, Vincent; Huang, L. R.; Lin, C. J.; Tseng, Y. N.; Huang, W. H.; Tuo, Laurent C.; Wylie, Mark; Chen, Ellison; Wang, Elvik; Glasser, Joshua; Kelkar, Amrish; Wu, David

    2015-10-01

    Die-to-die reticle inspections are among the simplest and most sensitive reticle inspections because of the use of an identical-design neighboring-die for the reference image. However, this inspection mode can have two key disadvantages: (1) The location of the defect is indeterminate because it is unclear to the inspector whether the test or reference image is defective; and (2) nuisance and false defects from mask manufacturing noise and tool optical variation can limit the usable sensitivity. The use of a new sequencing approach for a die-to-die inspection can resolve these issues without any additional scan time, without sacrifice in sensitivity requirement, and with a manageable increase in computation load. In this paper we explore another approach for die-to-die inspections using a new method of defect processing and sequencing. Utilizing die-to-die double arbitration during defect detection has been proven through extensive testing to generate accurate placement of the defect in the correct die to ensure efficient defect disposition at the AIMS step. The use of this method maintained the required inspection sensitivity for mask quality as verified with programmed-defectmask qualification and then further validated with production masks comparing the current inspection approach to the new method. Furthermore, this approach can significantly reduce the total number of defects that need to be reviewed by essentially eliminating the nuisance and false defects that can result from a die-to-die inspection. This "double-win" will significantly reduce the effort in classifying a die-to-die inspection result and will lead to improved cycle times.

  18. Graphite/Thermoplastic-Pultrusion Die

    NASA Technical Reports Server (NTRS)

    Wilson, Maywood L.; Frye, Mark W.; Johnson, Gary S.; Stanfield, Clarence E.

    1990-01-01

    Attachment to extruder produces thermoplastic-impregnated graphite tape. Consists of profile die, fiber/resin collimator, and crosshead die body. Die designed to be attached to commercially available extrusion machine capable of extruding high-performance thermoplastics. Simple attachment to commercial extruder enables developers of composites to begin experimenting with large numbers of proprietary resins, fibers, and hybrid composite structures. With device, almost any possible fiber/resin combination fabricated.

  19. The dying animal.

    PubMed

    Pierce, Jessica

    2013-12-01

    The study of animal death is poised to blossom into an exciting new interdisciplinary field-and one with profound relevance for bioethics. Areas of interest include the biology and evolution of death-related behavior in nonhuman animals, as well as human social, psychological, cultural, and moral attitudes toward and practices related to animal death. In this paper, I offer a brief overview of what we know about death-related behavior in animals. I will then sketch some of the bioethical implications of this emerging field of research. PMID:24092402

  20. PHYTOCHROME OVERVIEW

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Plants utilize light not only for photosynthesis but also as environmental signals. They are capable of perceiving wavelength, intensity, direction, duration, and other attributes of light to perform appropriate physiological and developmental changes. This volume presents overviews of and the lates...

  1. Sinusitis: Overview

    MedlinePlus

    MENU Return to Web version Sinusitis Overview What are sinuses? Sinuses are the air chambers in the bone behind your cheeks, eyebrows and jaw. They make mucus, a fluid that cleans bacteria and other particles out of the air you breathe. Tiny hairs called cilia (say: “sill-ee-ah”) sweep mucus out of your ...

  2. Historical Overview

    ERIC Educational Resources Information Center

    Scharlach, Andrew

    2008-01-01

    In this article, the author presents a historical overview of four decades of scholarship and changing public policy on family and informal caregiving for older adults. Families are changing at a dizzying pace. Changes in family composition, cultural diversity, geographic mobility, and societal norms, coupled with increasing numbers of older…

  3. Foreigners dying in Istanbul.

    PubMed

    Uzun, Ibrahim; Celbis, Osman; Baydar, Cetin Lutfi; Alkan, Nevzat; Arslan, Murat Nihat

    2009-09-01

    The study included 411 deaths selected from 14,647 medicolegal deaths autopsied in the Morgue Department of Forensic Medicine Institute Directorate, affiliated with the Ministry of Justice, between 1998 and 2002. Data were collected from court documents, coroner's investigation reports, and autopsy reports. The parameters of age, gender, nationality and origin, cause and place of death in foreigners dying in Istanbul were evaluated in the study. Out of 14,647 medicolegal deaths, 3.5% were foreigners from 34 different nationalities. The nationality with the highest rate of foreigner deaths (34%) was Romanian. Out of 411 deaths, 74.3% were male and 25.7% were female. Of all cases, 64.4% were tourists visiting Istanbul and 35.6% had a job in Istanbul. Of 146 foreigners employed in Istanbul, 94.5% did not have a work permit, while only 5.5% had a work permit. PMID:19674242

  4. Two Piece Compaction Die Design

    SciTech Connect

    Coffey, Ethan N

    2010-03-01

    Compaction dies used to create europium oxide and tantalum control plates were modeled using ANSYS 11.0. Two-piece designs were considered in order to make the dies easier to assemble than the five-piece dies that were previously used. The two areas of concern were the stresses at the interior corner of the die cavity and the distortion of the cavity wall due to the interference fit between the two pieces and the pressure exerted on the die during the compaction process. A successful die design would have stresses less than the yield stress of the material and a maximum wall distortion on the order of 0.0001 in. Design factors that were investigated include the inner corner radius, the value of the interference fit, the compaction force, the size of the cavity, and the outer radius and geometry of the outer ring. The results show that for the europium oxide die, a 0.01 in. diameter wire can be used to create the cavity, leading to a 0.0055 in. radius corner, if the radial interference fit is 0.003 in. For the tantalum die, the same wire can be used with a radial interference fit of 0.001 in. Also, for the europium oxide die with a 0.003 in. interference fit, it is possible to use a wire with a diameter of 0.006 in. for the wire burning process. Adding a 10% safety factor to the compaction force tends to lead to conservative estimates of the stresses but not for the wall distortion. However, when the 10% safety factor is removed, the wall distortion is not affected enough to discard the design. Finally, regarding the europium oxide die, when the cavity walls are increased by 0.002 in. per side or the outer ring is made to the same geometry as the tantalum die, all the stresses and wall distortions are within the desired range. Thus, the recommendation is to use a 0.006 in. diameter wire and a 0.003 in. interference fit for the europium oxide die and a 0.01 in. diameter wire and a 0.001 in. interference fit for the tantalum die. The dies can also be made to have the

  5. INL Overview

    ScienceCinema

    None

    2013-05-28

    Sure, we're the nation's leading nuclear-energy research lab ? but we're so much more than that! Check out INL's new hi-def overview video, which breaks down who we are and what we do. You might also want to surf on over to our facebook site http://www.facebook.com/idahonationallaboratory to see what kind of job openings we may have for you.

  6. Overview Presentation

    NASA Technical Reports Server (NTRS)

    Lytle, John

    2001-01-01

    This report provides an overview presentation of the 2000 NPSS (Numerical Propulsion System Simulation) Review and Planning Meeting. Topics include: 1) a background of the program; 2) 1999 Industry Feedback; 3) FY00 Status, including resource distribution and major accomplishments; 4) FY01 Major Milestones; and 5) Future direction for the program. Specifically, simulation environment/production software and NPSS CORBA Security Development are discussed.

  7. INL Overview

    SciTech Connect

    2010-01-01

    Sure, we're the nation's leading nuclear-energy research lab — but we're so much more than that! Check out INL's new hi-def overview video, which breaks down who we are and what we do. You might also want to surf on over to our facebook site http://www.facebook.com/idahonationallaboratory to see what kind of job openings we may have for you.

  8. Adapt or die?

    PubMed

    Visser, S S; Nel, A H

    1996-12-01

    The worldwide economic recession and the concomitant limited stock of finances have had an influence on the available money of every household and have also inhibited the improvement of socio-economic conditions and medicine. The Reconstruction and Development Programme (RDP) has the objective of improving the living conditions of the people with regard to housing, education, training and health care. The latter seems to be a major problem which has to be addressed with the emphasis on the preventive and promotional aspects of health care. A comprehensive health care system did not come into being property in the past because of the maldistribution of health care services, personnel and differences in culture and health care beliefs and values. The question that now arises, is how to render a quality health care service within the constraints of inadequate financing and resources. A comprehensive literature study has been done with reference to quality health care and financing followed by a survey of existing health services and finances. Recommendations are made about minimum requirements to be accepted if one were to adapt rather than die in terms of the provision of healthcare: the decentralization and rationalization of the administration of health care, the stress on and realization of effective and efficient primary health care, the acceptance of participative management in health providing organizations, the provision of financial management training for health care managers and the application of management accounting principles for the improvement of the efficiency and effectiveness of management. PMID:9283343

  9. Dying and multiplying life.

    PubMed

    Rodríguez-Arias, David

    2014-09-01

    It was only after James P. Lovette's death, in 2006, that I discovered that the twenty-four-year-old colleague and friend with whom I had spent so many afternoons debating issues in organ transplantation had been the first successful child heart transplantee in the world and one of the longest-living survivors of a second transplant. During the years we met, he never even hinted at the fact that three different hearts had beaten in his chest. The revelation that his life had been an almost uninterrupted chain of medical challenges suddenly made me appreciate his quirkiness in a whole new light. Organ transplantation crudely exemplifies a traditional moral dilemma between means and ends: in order to save a life, someone else has to die. Bioethicists involved in this field have the role of identifying the ethical issues surrounding organ donation and helping others to argue in an intelligible and convincing way. In my view, bioethicists have the obligation to foster a discussion as open and transparent as possible on these matters. Still, I sometimes fear that I may be helping to cause unnecessary harms to potential recipients who are desperately waiting for a vital organ. Scholars would be chillingly cold if their quest for truth systematically came at the cost of lives lost. Every life can be meaningful and provide meaning to many others. This is true even with organ recipients, who often have short lives full of considerable suffering. PMID:25231665

  10. PHOBOS Overview

    NASA Astrophysics Data System (ADS)

    Hofman, David J.; Phobos Collaboration; Bbback; Baker, M. D.; Ballintijn, M.; Barton, D. S.; Betts, R. R.; Bickley, A. A.; Bindel, R.; Budzanowski, A.; Busza, W.; Carroll, A.; Chai, Z.; Decowski, M. P.; García, E.; Gburek, T.; George, N.; Gulbrandsen, K.; Gushue, S.; Halliwell, C.; Hamblen, J.; Hauer, M.; Heintzelman, G. A.; Henderson, C.; Hollis, R. S.; Hołyński, R.; Holzman, B.; Iordanova, A.; Johnson, E.; Kane, J. L.; Khan, N.; Kulinich, P.; Kuo, C. M.; Lin, W. T.; Manly, S.; Mignerey, A. C.; Nouicer, R.; Olszewski, A.; Pak, R.; Park, I. C.; Reed, C.; Roland, C.; Roland, G.; Sagerer, J.; Seals, H.; Sedykh, I.; Smith, C. E.; Stankiewicz, M. A.; Steinberg, P.; Stephans, G. S. F.; Sukhanov, A.; Tonjes, M. B.; Trzupek, A.; Vale, C.; van Nieuwenhuizen, G. J.; Vaurynovich, S. S.; Verdier, R.; Veres, G. I.; Wenger, E.; Wolfs, F. L. H.; Wosiek, B.; Kwoźniak; Wysłouch, B.

    2006-11-01

    A brief overview of the current results and conclusions from the PHOBOS experiment at the Relativistic Heavy Ion Collider (RHIC) is given. No evidence is found for non-monotonic behavior of observables measured by PHOBOS in the RHIC energy region. Convincing evidence is found that we have created a state of matter with high energy-density, that is nearly net-baryon free and is strongly interacting. The data are found to exhibit "simple" scaling behaviors, which include extended longitudinal scaling and scaling with the number of participating nucleons. The Au+Au collision charged particle data also exhibit a remarkable factorization of collision energy and geometry.

  11. SAFSIM overview

    NASA Technical Reports Server (NTRS)

    Dobranich, Dean

    1993-01-01

    An overview of the systems analysis flow simulator (SAFSIM) computer program is provided. SAFSIM is being developed at Sandia National Laboratories and is currently funded by the Air Force Space Nuclear Thermal Propulsion (SNTP) Program. SAFSIM is a general purpose, Fortran computer program to simulate the integrated performance of complex systems involving fluid mechanics, heat transfer, and reactor dynamics. SAFSIM provides sufficient versatility to allow the engineering simulation of almost any system. SAFSIM is based on a 1-D finite element model and provides the analyst with approximate solutions to complex problems.

  12. What Happens When Someone Dies?

    MedlinePlus

    ... and sleepiness Mental confusion Constipation or incontinence Nausea Refusal to eat or drink Each of these symptoms, ... having a "non-hospital DNR" (see Understanding Health Care Decisions ) if the person is dying at home. ...

  13. Improving care of dying children.

    PubMed Central

    Martinson, I M

    1995-01-01

    Every year about 5,000 children aged 0 to 14 years need hospice care in the United States. Children seem to know that they are dying, although this is difficult for parents to accept. Clear, empathic understanding is needed. Communication with clarity and understanding is imperative with the changes in goals from cure to palliation to comfort. The ideal place for most dying children is at home, where symptoms can be managed as effectively as in a hospital. PMID:7571589

  14. REFRACTORY DIE FOR EXTRUDING URANIUM

    DOEpatents

    Creutz, E.C.

    1959-08-11

    A die is presented for the extrusion of metals, said die being formed of a refractory complex oxide having the composition M/sub n/O/sub m/R/sub x/O/sub y/ where M is magnesium, zinc, manganese, or iron, R is aluminum, chromic chromium, ferric iron, or manganic manganese, and m, n, x, and y are whole numbers. Specific examples are spinel, magnesium aluminate, magnetite, magnesioferrite, chromite, and franklinite.

  15. Tsunami overview.

    PubMed

    Morrow, Robert C; Llewellyn, D Mark

    2006-10-01

    Historically, floods and tsunamis have caused relatively few severe injuries; an exception to that tendency followed the great Andaman Island-Sumatra earthquake and tsunami of 2004. More than 280,000 people died, the coastal plains were massively scoured, and more than 1 million individuals were made homeless by the quake and resulting tsunami, which affected a 10-nation region around the Indian Ocean. This destruction overwhelmed local resources and called forth an unprecedented, prolonged, international response. The USNS Mercy deployed on a unique mission and rendered service to the people and government of Indonesia. This introduction provides background on the nature and extent of the damage, conditions upon arrival of the hospital ship 5 weeks after the initial destruction, and the configuration of professionals aboard (officers and sailors of the U.S. Navy, civilian volunteers from Project HOPE, officers of the U.S. Public Health Service, and officers and civilian mariners of the Military Sealift Command). Constraints on the mission provide context for the other articles of this issue that document and comment on the activities, challenges, methods, and accomplishments of this unique mission's "team of teams," performing humanitarian assistance and disaster relief in the Pacific theater. PMID:17447612

  16. Use of RSP Tooling to Manufacture Die Casting Dies

    SciTech Connect

    Kevin McHugh

    2004-07-01

    The technology and art used to construct die casting dies has seen many improvements over the years. However, the time lag from when a design is finalized to the time a tool is in production has remained essentially the same. The two main causes for the bottleneck are the need to qualify a part design by making prototypes (usually from an alternative process), and the production tooling lead time after the prototypes are approved. Production tooling costs are high due to the labor and equipment costs associated with transforming a forged block of tool steel into a finished tool. CNC machining, sink EDM, benching, engraving and heat treatment unit operations are typically involved. As a result, there is increasing interest in rapid tooling (RT) technologies that shorten the design-to-part cycle and reduce the cost of dies. There are currently more than 20 RT methods being developed and refined around the world (1). The "rapid" in rapid tooling suggests time compression for tool delivery, but does not address robustness as nearly all RT approaches are intended for low-volume prototype work, primarily for molding plastics. Few options exist for die casting. An RT technology suitable for production-quality tooling in the time it normally takes for prototype tooling is highly desirable. In fact, there would be no need for a distinction between prototype and production tooling. True prototype parts could be made using the same processing conditions and materials intended for production. Qualification of the prototype part would allow the manufacturer to go directly into production with the same tool. A relatively new RT technology, Rapid Solidification Process (RSP) Tooling, is capable of making production-quality tooling in an RT timeframe for die casting applications. RSP Tooling, was developed at the Idaho National Engineering and Environmental Laboratory (INEEL), and commercialized with the formation of RSP Tooling, LLC (2). This paper describes the process, and

  17. Acting to let someone die.

    PubMed

    McGee, Andrew

    2015-02-01

    This paper examines the recent prominent view in medical ethics that withdrawing life-sustaining treatment (LST) is an act of killing. I trace this view to the rejection of the traditional claim that withdrawing LST is an omission rather than an act. Although that traditional claim is not as problematic as this recent prominent view suggests, my main claim is that even if we accepted that withdrawing LST should be classified as an act rather than as an omission, it could still be classified as letting die rather than killing. Even though omissions are contrasted with acts, letting die need not be, for one can let die by means of acts. The remainder of the paper is devoted to establishing this claim and addresses certain objections to it. PMID:24320715

  18. Clinical management of dying patients.

    PubMed Central

    Gavrin, J; Chapman, C R

    1995-01-01

    Dying is universal, and death should be a peaceful time. Myriad comfort measures are available in the last weeks before life ends. Discussions about end-of-life issues often suffer from lack of informed opinion. Palliative care experts have identified specific somatic and psychological sources of distress for dying patients and their loved ones. Pain, shortness of breath, nausea and vomiting, and fear of abandonment contribute substantially to both physical and psychological discomfort toward the end of life. Simple, effective methods exist for relieving those symptoms. Knowledge about the natural events associated with dying and an informed approach to medical and psychological interventions contribute to systematic and successful comfort care. We describe the origin of physical and psychological distress at the end of life and provide strategies for alleviating many of the discomforts. PMID:7571591

  19. 'Die Zeit' im Konversationsunterricht ('Die Zeit' in a Conversation Class)

    ERIC Educational Resources Information Center

    Becker-Cantarino, Barbel

    1975-01-01

    The German weekly newspaper "Die Zeit" contains a very rich variety of topics and is therefore an inexhaustable source for an exciting conversation class. This article outlines and lists the advantages of a German conversation course organized around this newspaper. (Text is in German.) (TL)

  20. Dying radio galaxies in clusters

    NASA Astrophysics Data System (ADS)

    Murgia, M.; Parma, P.; Mack, K.-H.; de Ruiter, H. R.; Fanti, R.; Govoni, F.; Tarchi, A.; Giacintucci, S.; Markevitch, M.

    2011-02-01

    Aims: We present a study of five "dying" nearby (z ≤ 0.2) radio galaxies belonging to both the WENSS minisurvey and the B2 bright catalogs WNB1734+6407, WNB1829+6911, WNB1851+5707, B2 0120+33, and B2 1610+29. Methods: These sources have been selected on the basis of their extremely steep broad-band radio spectra, which strongly indicates that either these objects belong to the rare class of dying radio galaxies or we are observing "fossil" radio plasma remaining from a previous instance of nuclear activity. We derive the relative duration of the dying phase from the fit of a synchrotron radiative model to the radio spectra of the sources. Results: The modeling of the integrated spectra and the deep spectral index images obtained with the VLA confirmed that in these sources the central engine has ceased to be active for a significant fraction of their lifetime, although their extended lobes have not yet completely faded away. We found that WNB1851+5707 is in reality composed of two distinct dying galaxies, which appear blended together as a single source in the WENSS. In the cases of WNB1829+6911 and B2 0120+33, the fossil radio lobes are seen in conjunction with a currently active core. A very faint core is also detected in a MERLIN image of WNB1851+5707a, one of the two dying sources composing WNB1851+5707. We found that all sources in our sample are located (at least in projection) at the center of an X-ray emitting cluster. Conclusions: Our results suggest that the duration of the dying phase for a radio source in a cluster can be significantly higher than that of a radio galaxy in the field, although no firm conclusions can be drawn because of the small number statistics involved. The simplest interpretation of the tendency for dying galaxies to be found in clusters is that the low-frequency radio emission from the fading radio lobes lasts longer if their expansion is somewhat reduced or even stopped. Another possibility is that the occurrence of dying

  1. Die Herz-Lungen-Maschine

    NASA Astrophysics Data System (ADS)

    Krane, Markus; Bauernschmitt, Robert; Lange, Rüdiger

    Das Kapitel der modernen Herzchirurgie mit Einsatz der Herz-Lungen-Maschine am Menschen beginnt am 6. Mai 1953, als J. Gibbon bei einer 18-jährigen Patientin einen angeborenen Defekt in der Vorhofscheidewand verschließt [1]. Mit ersten experimentellen Versuchen zur extrakorporalen Zirkulation begann Gibbon bereits in den 30er Jahren des 20. Jahrhunderts. Die Grundlage für die heute gebräuchliche Rollerpumpe schufen Porter und Bradley mit ihrer "rotary pump“, welche sie 1855 zum Patent anmeldeten. Diese Pumpe wurde von DeBakey und Schmidt modifiziert und entspricht im Wesentlichen noch der heute sich im Routinebetrieb befindlichen Rollerpumpe [2].

  2. Portable punch and die jig

    DOEpatents

    Lewandowski, Edward F.; Anderson, Petrus A.

    1978-01-01

    A portable punch and die jig includes a U-shaped jig of predetermined width having a slot of predetermined width in the base thereof extending completely across the width of the jig adapted to fit over the walls of rectangular tubes and a punch and die assembly disposed in a hole extending through the base of the jig communicating with the slot in the base of the jig for punching a hole in the walls of the rectangular tubes at precisely determined locations.

  3. High-Pressure Die-Casting: Contradictions and Challenges

    NASA Astrophysics Data System (ADS)

    Bonollo, Franco; Gramegna, Nicola; Timelli, Giulio

    2015-05-01

    High-pressure die casting (HPDC) is particularly suitable for high production rates and it is applied in several industrial fields; actually, approximately half of the world production of light metal castings is obtained by this technology. An overview of the actual status of HPDC technology is described in the current work, where both critical aspects and potential advantages are evidenced. Specific attention is paid to the quality requirements from the end users, as well as to the achievable production rate, the process monitoring and control, and the European and worldwide scenario. This overview leads to individuate the most relevant challenges for HPDC industry: "zero-defect" production, real-time process control, understanding the role of the process variables, process optimization, introduction of research and development activities, and disseminating the knowledge about HPDC technology. Performing these actions, HPDC foundries could achieve a more mature and efficient approach to large end users and exploit their really relevant potential.

  4. Science Overview

    NASA Technical Reports Server (NTRS)

    Bruning, Claus; Ko, Malcolm; Lee, David; Miake-Lye, Richard

    2006-01-01

    This report presents an overview of the latest scientific consensus understanding of the effect of aviation emissions on the atmosphere for both local air quality and climate change in order to provide a contextual framework for raising future questions to help assess the environmental benefits of technology goals. The questions may take the form of what are the environmental benefits that would result if goals are achieved, what are the consequences for other aviation pollutants, and whether tools exist to evaluate the trade-off. In addition to this documents, presentations will be made at the meeting to illustrate current developing views on these subjects. To facilitate studies on trade-offs among environmental impacts from aviation, one must start with scientific investigations that quantify the impacts. A second step is to select representative metrics with policy relevance so that diverse impacts can be put on the same common scale. The IPCC Special Report on Aviation (IPCC, 1999) serves as an excellent example of the first step. The report was produced by IPCC's Working Group 1, whose mandate is to provide the assessment of the scientific aspects of the climate system and climate change. An example of the second step is Witt et al. (2005), a study commissioned by the Environment DG of the European Commission. Within the context of CAEP, step 1 is aligned with the responsibilities of the Research Focal Points, while step 2 is more related to activities of FESG. These steps are likely to be iterative as proposed policy options will raise new science questions, and new science will expand or limit policy options. Past experiences show that clearly defined policy-related scientific needs will help focus the scientific community to marshal their intellects to provide the needed answers.

  5. Robert Merton Dies at 92

    ERIC Educational Resources Information Center

    Snell, Joel C.

    2006-01-01

    This article features Robert Merton, who died recently at age 92. Merton came into this world as a Jewish baby named Meyer Schkolnick. He lived in South Philly where his parents wrenched a living as blue-collar workers. Merton chose an Anglicized name to move into the Yankee dominated America of the 20's and 30's. At Harvard, he studied under…

  6. Attitudes on Death and Dying.

    ERIC Educational Resources Information Center

    Andrus, Charles E.

    This paper explored attitudes toward death and dying revealed through interviews with members of the clergy, the medical profession, funeral directors, nursing home residents, and selected others. The sampling was small and results are not intended to be representative of the groups to which these people belong. Rather, the study may be used as a…

  7. End-of-Life Care: An Overview for Professional Counselors

    ERIC Educational Resources Information Center

    Werth, James L.; Crow, Laura

    2009-01-01

    Although "End-of-Life Care for Terminally Ill Clients" is a section of the "ACA Code of Ethics" (American Counseling Association, 2005), neither the "Code" nor the counseling literature provides much direction for counselors who work with clients who are dying and with the clients' loved ones. The authors provide counselors with an overview of the…

  8. Integrated Forming Simulations and Die Structural Analysis for Optimal Die Designs

    NASA Astrophysics Data System (ADS)

    Aitharaju, Venkat; Liu, Malcolm; Dong, Jennifer; Zhang, Jimmy; Wang, Chuan-tao

    2005-08-01

    After gaining a huge success in applying stamping simulations and formability analysis to validate die face developments, GM moves forward to winning total manufacturability in stamping process. Of which, ensuring die structure integrity and minimizing weight is one of the important initiatives. Stamping die design (or solid modeling of stamping dies) was traditionally conducted by following the die design manuals and standards. For any design changes beyond the standards, however, there are no math-based tools available to die designers to verify the outcome of the changes. Die structural analysis (DSA) provides a math-tool to validate the design changes and quantify the safety factors. Several years ago, GM Manufacturing Engineering — Die Center started die structural analysis to meet the increasing demands of customer needs in various areas: (1) to validate design changes; (2) to identify root cause of die breakage during the tryout and stamping operations and propose repair schemes; (3) to optimize the die design for weight reduction; (4) to improve press throughput via optimizing the scrap chute openings, and (5) to provide a math-based tool to validate revisions to the current die design standards. In the integrated forming and die structural analysis, after successful line die surface developments, the forming loads (binder force, pad force, and forming tonnages) are extracted from forming simulations and applied to solid die members for structural analyses of stress, strains, and deflections. In the past few years, Die Center conducted static, dynamic and fatigue analysis for many dies that covers the die design changes requested by die design, die construction and stamping plants. This paper presents some fundamentals and issues of integrated forming and die structural analysis and illustrates the significant impact of die structural analysis on die design, die construction and production stamping.

  9. Exploratory study on H13 steel dies

    SciTech Connect

    Sunwoo, A.J.

    1994-04-01

    Ultrahigh-strength H13 steel is a recommended die material for aluminum die casting; dies made from H13 steel can be safely water- cooled during hot working operations without cracking. However, after time the dies exhibited surface cracking and excessive wear. Erosive wear also occurs owing to high pressure injection of molten Al. An exploratory study was made of the causes for surface cracking of H13 dies. Results suggest that surface cracking is caused by interrelated factors, internal to the die material as well as externally induced conditions.

  10. The thermal fatigue resistance of H-13 Die Steel for aluminum die casting dies

    NASA Technical Reports Server (NTRS)

    1982-01-01

    The effects of welding, five selected surface coatings, and stress relieving on the thermal fatigue resistance of H-13 Die Steel for aluminum die casting dies were studied using eleven thermal fatigue specimens. Stress relieving was conducted after each 5,000 cycle interval at 1050 F for three hours. Four thermal fatigue specimens were welded with H-13 or maraging steel welding rods at ambient and elevated temperatures and subsequently, subjected to different post-weld heat treatments. Crack patterns were examined at 5,000, 10,000, and 15,000 cycles. The thermal fatigue resistance is expressed by two crack parameters which are the average maximum crack and the average cracked area. The results indicate that a significant improvement in thermal fatigue resistance over the control was obtained from the stress-relieving treatment. Small improvements were obtained from the H-13 welded specimens and from a salt bath nitrogen and carbon-surface treatment. The other surface treatments and welded specimens either did not affect or had a detrimental influence on the thermal fatigue properties of the H-13 die steel.

  11. Guide for extrusion dies eliminates straightening operation

    NASA Technical Reports Server (NTRS)

    Gyorgak, C. A.; Hoover, R. J.

    1964-01-01

    To prevent distortion of extruded metal, a guidance assembly is aligned with the die. As the metal emerges from the extrusion dies, it passes directly into the receiver and straightening tube system, and the completed extrusion is withdrawn.

  12. [Dying with cancer: Hollywood lessons].

    PubMed

    Niemeyer, Fernanda; Kruse, Maria Henriqueta Luce

    2013-12-01

    The study attempts to understand how dying from cancer is portrayed by five movies produced in Hollywood between 1993 and 2006. Based on the cultural studies and their post-structuralism version and supported by the notions of discourse and subjectivity, as proposed by philosopher Michel Foucault, we suggest one of the possible readings of the movie picture corpus. We assess how the movie picture discourse acts as a cultural pedagogy that produces ways of seeing dying with cancer: immortalizing the healthy body image, silencing death, taking care of the dead body and, finally, accepting death. Our proposal is intended to stimulate reflections that may contribute to care and education in nursing. PMID:25080714

  13. Adolescents’ Perceived Risk of Dying

    PubMed Central

    Fischhoff, Baruch; de Bruin, Wändi Bruine; Parker, Andrew M.; Millstein, Susan G.; Halpern-Felsher, Bonnie L.

    2009-01-01

    Purpose Although adolescents’ expectations are accurate or moderately optimistic for many significant life events, they greatly overestimate their chances of dying soon. We examine here whether adolescents’ mortality judgments are correlated with their perceptions of direct threats to their survival. Such sensitivity would indicate the importance of ensuring that adolescents have accurate information about those threats, as well as the psychological support needed to deal with them. Methods Data from two separate studies were used: a national study of 3,436 14–18 year old adolescents and a regional sample of 124 7th graders and 132 9th graders, 12–16 years old. Participants were asked about their chance of dying in the next year and before age 20, and about the extent of various threats to their physical well being. Results Adolescents in both samples greatly overestimated their chance of dying. Those mortality estimates were higher for adolescents who reported direct threats (e.g., an unsafe neighborhood). Thus, adolescents were sensitive to the relative size of threats to their survival, but not to the implications for absolute risk levels. Conclusions Contrary to the folk wisdom that adolescents have a unique sense of invulnerability, those studied here reported an exaggerated sense of mortality, which was highest among those reporting greater threats in their lives. Such fears could affect adolescents’ short-term well being and future planning. PMID:20159504

  14. Killing, letting die and euthanasia.

    PubMed

    Husak, D N

    1979-12-01

    Medical ethicists debate whether or not the moral assessment of cases of euthanasia should depend on whether the patient is 'killed' or 'allowed to die'. The usual presupposition is that a clear distinction between killing and letting die can be drawn so that this substantive question is not begged. I contend that the categorisation of cases of instances of killing rather than as instances of letting die depends in part on a prior moral assessment of the case. Hence is it trivially rather than substantively true that the distinction has moral significance. But even if a morally neutral (ie non-question begging) distinction could be drawn, its application to the euthanasia controversy is problematic. I illustrate the difficulties of employing this distinction to reach moral conclusions by critically discussing Philippa Foot's recent treatment of euthanasia. I conclude that even if an act of euthanasia is an instance of killing, and there exists a prima facie moral duty not to kill, and no more stringent duty overrides this duty, one still cannot determine such an act to be morally impermissible. PMID:541821

  15. Jewish tradition in death and dying.

    PubMed

    Ross, H M

    1998-10-01

    Death is often a spiritually difficult time for the dying and their families. Judaism approaches dying with some unique views that can differ from other religious traditions. Through an understanding of Jewish tradition, nurses can ease the dying process for Jewish patients and their families. PMID:10036429

  16. Contoured Orifice for Silicon-Ribbon Die

    NASA Technical Reports Server (NTRS)

    Mackintosh, B. H.

    1985-01-01

    Die configuration encourages purity and stable growth. Contour of die orifice changes near ribbon edges. As result, silicon ribbon has nearly constant width and little carbon contamination. Die part of furnace being developed to produce high-quality, low-cost material for solar cells.

  17. Breast Cancer Overview

    MedlinePlus

    ... Breast Cancer - Overview Request Permissions Print to PDF Breast Cancer - Overview Approved by the Cancer.Net Editorial Board , ... bean-shaped organs that help fight infection. About breast cancer Cancer begins when healthy cells in the breast ...

  18. Die Welt des Herrn Kuhn

    NASA Astrophysics Data System (ADS)

    Kern, Daniela

    Eines Morgens erwachte Herr Kuhn fröstelnd und staunte darüber, dass es in seinerWohnung eiskalt war. Dennoch quälte er sich aus seiner kuscheligen Bettdecke heraus und schlurfte ins Bad. "Hoffentlich wird wenigstens das Wasser warm", dachte er sich, als er den Wasserhahn betätigte - aber es kam nicht nur kein warmesWasser, außer einem unheilvollen Gluckser kam gar nichts aus der Leitung. "Dann werde ich wohl mal den Klempner anrufen", sprach er sich leise in den Bart und griff zu seinem Handy - doch das Netz war tot! Herr Kuhn begann nun, sich ernsthaft Sorgen zu machen, "Oje, was ist denn heute nur los? Ist irgendetwas Schlimmes passiert?" Um einen besseren Überblick über die Lage zu bekommen und sich austauschen zu können, brannte er nun förmlich darauf, rauszugehen und zur Arbeit zu fahren. An anderen Tagen, die er frisch geduscht und mit Kaffee und Marmeladen-Brot begann, war er selten so motiviert. So ging er also nun mit leerem Magen aus dem Haus. Hätte er den Versuch unternommen, sein tägliches Marmeladenbrot zuzubereiten, und dafür den Kühlschrank geöffnet, um das Marmeladenglas herauszunehmen, wäre ihm aufgefallen, dass auch die Stromversorgung Störungen unterworfen war, unschön zu erkennen an den ersten grünen, felligen Inseln auf seinem Lieblingskäse.

  19. Evaluation of permanent die coatings to improve the wear resistance of die casting dies. Final project report, January 1, 1995--April 30, 1997

    SciTech Connect

    Shivpuri, R.

    1997-09-18

    Die Casting dies are subject to severe service conditions during the die casting operation. While these severe conditions are necessary to achieve high production rates, they cause the dies which are commonly made of H13 die steel, to suffer frequent failures. The major die failure mechanisms are erosion or washout, Heat checking, soldering and corrosion. Due to their geometrical complexity, die casting dies are very expensive (some dies cost over a million dollars), and thus a large number of parts have to be produced by a die, to justify this cost and leverage the advantages of the die casting process (high production rates, low manpower costs). A potential increase in the die service life, thus has a significant impact on the economics of the die; casting operation. There are many ways to extend die life: developing new wear resistant die materials, developing new surface treatments including coatings, improving heat treatment of existing H13 dies, using better lubricants that can protect the die material, or modifying the die geometry and process parameters to reduce the intensity of wear. Of these the use of coatings to improve the wear resistance of the die surface has shown a lot of promise. Consequently, use of coatings in the die casting industry and their wide use to decrease die wear can improve significantly the productivity of shop operations resulting in large savings in material and energy usage.

  20. Reinraumtechnik für die Medizintechnik

    NASA Astrophysics Data System (ADS)

    Petek, Max; Jungbluth, Martin; Krampe, Erhard

    Die Reinraumtechnik ist heute ein unverzichtbarer Bestandteil bei der Fertigung von Produkten der Life Sciences, den Bereichen Pharma, Lebensmittel, Kosmetik und Medizintechnik. In Anbetracht der langen Historie der Medizintechnik ist sie jedoch eine sehr junge Disziplin. Die Bedeutung von Keimen und die richtige Einschätzung ihrer Größe wurden zwar sehr früh bereits durch Paracelsus erkannt, jedoch wurden daraus noch keine speziellen oder kontinuierlich umgesetzten Hygienevorschriften abgeleitet. Die erste bekannte technische Umsetzung von Hygieneempfehlungen geht auf den Franzosen François Nicolas Appert zurück, der eine aseptische Abfüllmethode für Lebensmittel entwickelte und diese 1810 veröffentlichte [1]. Die erste dokumentierte medizinische Umsetzung stellten Hygienevorschriften für Ärzte dar, die Ignaz Philipp Semmelweis nach 1847 in der Wiener Klinik für Geburtshilfe einführte [2].

  1. Vacuum die attach for integrated circuits

    DOEpatents

    Schmitt, Edward H.; Tuckerman, David B.

    1991-01-01

    A thin film eutectic bond for attaching an integrated circuit die to a circuit substrate is formed by coating at least one bonding surface on the die and substrate with an alloying metal, assembling the die and substrate under compression loading, and heating the assembly to an alloying temperature in a vacuum. A very thin bond, 10 microns or less, which is substantially void free, is produced. These bonds have high reliability, good heat and electrical conduction, and high temperature tolerance. The bonds are formed in a vacuum chamber, using a positioning and loading fixture to compression load the die, and an IR lamp or other heat source. For bonding a silicon die to a silicon substrate, a gold silicon alloy bond is used. Multiple dies can be bonded simultaneously. No scrubbing is required.

  2. Die singulation method and package formed thereby

    SciTech Connect

    Anderson, Robert C.; Shul, Randy J.; Clews, Peggy J.; Baker, Michael S.; De Boer, Maarten P.

    2012-08-07

    A method is disclosed for singulating die from a substrate having a sacrificial layer and one or more device layers, with a retainer being formed in the device layer(s) and anchored to the substrate. Deep Reactive Ion Etching (DRIE) etching of a trench through the substrate from the bottom side defines a shape for each die. A handle wafer is then attached to the bottom side of the substrate, and the sacrificial layer is etched to singulate the die and to form a frame from the retainer and the substrate. The frame and handle wafer, which retain the singulated die in place, can be attached together with a clamp or a clip and to form a package for the singulated die. One or more stops can be formed from the device layer(s) to limit a sliding motion of the singulated die.

  3. Vacuum die attach for integrated circuits

    DOEpatents

    Schmitt, E.H.; Tuckerman, D.B.

    1991-09-10

    A thin film eutectic bond for attaching an integrated circuit die to a circuit substrate is formed by coating at least one bonding surface on the die and substrate with an alloying metal, assembling the die and substrate under compression loading, and heating the assembly to an alloying temperature in a vacuum. A very thin bond, 10 microns or less, which is substantially void free, is produced. These bonds have high reliability, good heat and electrical conduction, and high temperature tolerance. The bonds are formed in a vacuum chamber, using a positioning and loading fixture to compression load the die, and an IR lamp or other heat source. For bonding a silicon die to a silicon substrate, a gold silicon alloy bond is used. Multiple dies can be bonded simultaneously. No scrubbing is required. 1 figure.

  4. Physician-assisted dying and psychiatry: recent developments in The Netherlands.

    PubMed

    Pols, Hans; Oak, Stephanie

    2013-01-01

    The Netherlands was one of the first countries in the world to establish a legal framework for physician-assisted dying (PAD). In this article, we provide an overview of the public, political, legal, and medical debates on physician-assisted dying in The Netherlands, focusing on the role of psychiatry and mental illness. The number of individuals with chronic mental illness requesting PAD has been relatively small (although the number can be expected to increase because of the activities of various civic organizations advocating the right to die) and Dutch psychiatrists have been extremely reluctant to respond to such requests. Nevertheless, mental conditions have been central to the public debate on PAD by helping to define the nature and limits of current legislation and professional practice. Although a few Dutch psychiatrists have campaigned to increase the involvement of psychiatrists and many support PAD in principle, the majority has been hesitant to engage in PAD despite increasing public pressure. PMID:23816378

  5. Should assisted dying be legalised?

    PubMed Central

    2014-01-01

    When an individual facing intractable pain is given an estimate of a few months to live, does hastening death become a viable and legitimate alternative for willing patients? Has the time come for physicians to do away with the traditional notion of healthcare as maintaining or improving physical and mental health, and instead accept their own limitations by facilitating death when requested? The Universities of Oxford and Cambridge held the 2013 Varsity Medical Debate on the motion “This House Would Legalise Assisted Dying”. This article summarises the key arguments developed over the course of the debate. We will explore how assisted dying can affect both the patient and doctor; the nature of consent and limits of autonomy; the effects on society; the viability of a proposed model; and, perhaps most importantly, the potential need for the practice within our current medico-legal framework. PMID:24423249

  6. Overview of the Esophagus

    MedlinePlus

    ... the Esophagus Works Figure 1 How the Esophagus Works Esophageal and Swallowing Disorders Overview of the Esophagus Gastroesophageal Reflux (GERD) Hiatus Hernia Abnormal Propulsion of Food Achalasia ...

  7. Impact of Simulation Technology on Die and Stamping Business

    NASA Astrophysics Data System (ADS)

    Stevens, Mark W.

    2005-08-01

    minute. As we spread these simulation techniques to the balance of our business, from blank de-stacking to the racking of parts, we anticipate continued reduction in lead-time and engineering expense while improving quality and start-up execution. The author will provide an overview of technology and business evolution of the math-based process that brought an historical transition and revitalization to the die and stamping industry in the past decade. Finally, the author will give an outlook for future business needs and technology development directions.

  8. Assisted dying: a review of international legislation.

    PubMed

    Field, Charlotte; Curtice, Martin

    2009-05-01

    The issue of assisted dying in the UK is increasingly receiving media and academic journal attention. Such reporting often cites, but in little depth, existing legislation in other countries. Such international legislation may also shape future UK assisted dying legislation. PMID:19451872

  9. The Right To Die. Public Talk Series.

    ERIC Educational Resources Information Center

    Pasquerella, Lynn

    This program guide on the right to die provides policy issue information where ethical concerns have a prominent place. Three positions about the right to die are presented: (1) mercy killing and assisted suicide should be legally permitted in certain cases; (2) legal status should be given to living wills and other advance directives that would…

  10. Die Evolution der Religiosität

    NASA Astrophysics Data System (ADS)

    Voland, Eckart

    Ein konsequent darwinischer Blick auf den Menschen bedeutet, auch im Denken, Fühlen und Handeln biologische Anpassungsgeschichte zu suchen, denn auch die psychischen und mentalen Eigenheiten des Homo sapiens unterliegen der natürlichen Selektion. Lässt sich die religiöse Lebenspraxis von Menschen daher auch aus einer Fitnessperspektive betrachten?

  11. Prediction of Part Distortion in Die Casting

    SciTech Connect

    R. Allen Miller

    2005-03-30

    The die casting process is one of the net shape manufacturing techniques and is widely used to produce high production castings with tight tolerances for many industries. An understanding of the stress distribution and the deformation pattern of parts produced by die casting will result in less deviation from the part design specification, a better die design and eventually more productivity and cost savings. This report presents methods that can be used to simulate the die casting process in order to predict the deformation and stresses in the produced part and assesses the degree to which distortion modeling is practical for die casting at the current time. A coupled thermal-mechanical finite elements model was used to simulate the die casting process. The simulation models the effect of thermal and mechanical interaction between the casting and the die. It also includes the temperature dependant material properties of the casting. Based on a designed experiment, a sensitivity analysis was conducted on the model to investigate the effect of key factors. These factors include the casting material model, material properties and thermal interaction between casting and dies. To verify the casting distortion predictions, it was compared against the measured dimensions of produced parts. The comparison included dimensions along and across the parting plane and the flatness of one surface.

  12. Student Nurses' Perception of Death and Dying

    ERIC Educational Resources Information Center

    Niederriter, Joan E.

    2009-01-01

    Student nurses are involved in caring for patients who are actively dying or who have been told they have a terminal illness and are faced with the process of dying. Students encounter these patients in hospitals, nursing homes, at home or in hospice care settings. According to Robinson (2004), "nurses are the healthcare providers that are most…

  13. Apparatus for restraining and transporting dies

    DOEpatents

    Allison, James W.; LaBarre, Timothy L.

    1994-01-01

    Apparatus for restraining and transporting dies in punch press operations is provided. A floatation platen for supporting a die on the platen's upper surface has a plurality of recessed gas exhaust ports on the platen's lower surface. A source of pressurized gas delivers gas to a platen manifold, for delivery to orifices located in the gas exhaust ports. The flow of gas is controlled by a first valve adjacent the gas source and a second valve adjacent the manifold, with the second valve being used to control the gas flow during movement of the die. In this fashion, a die may be moved on a cushion of air from one workstation to a selected second workstation. A moveable hydraulically operated restraining fixture is also provided, for clamping the die in position during the compacting phase, and for releasing the die after completion of the compacting phase by releasing the hydraulic pressure on the restraining fixture. When pressure in the hydraulic cylinders on the restraining fixture is reversed, the restraining fixture will retract so that there is no contact between the die and the restraining fixture, thereby allowing the die to be removed from a first workstation and moved to a second selected workstation.

  14. Energy Consumption of Die Casting Operations

    SciTech Connect

    Jerald Brevick; clark Mount-Campbell; Carroll Mobley

    2004-03-15

    Molten metal processing is inherently energy intensive and roughly 25% of the cost of die-cast products can be traced to some form of energy consumption [1]. The obvious major energy requirements are for melting and holding molten alloy in preparation for casting. The proper selection and maintenance of melting and holding equipment are clearly important factors in minimizing energy consumption in die-casting operations [2]. In addition to energy consumption, furnace selection also influences metal loss due to oxidation, metal quality, and maintenance requirements. Other important factors influencing energy consumption in a die-casting facility include geographic location, alloy(s) cast, starting form of alloy (solid or liquid), overall process flow, casting yield, scrap rate, cycle times, number of shifts per day, days of operation per month, type and size of die-casting form of alloy (solid or liquid), overall process flow, casting yield, scrap rate, cycle times, number of shifts per day, days of operation per month, type and size of die-casting machine, related equipment (robots, trim presses), and downstream processing (machining, plating, assembly, etc.). Each of these factors also may influence the casting quality and productivity of a die-casting enterprise. In a die-casting enterprise, decisions regarding these issues are made frequently and are based on a large number of factors. Therefore, it is not surprising that energy consumption can vary significantly from one die-casting enterprise to the next, and within a single enterprise as function of time.

  15. Live to die another way: modes of programmed cell death and the signals emanating from dying cells

    PubMed Central

    Fuchs, Yaron; Steller, Hermann

    2015-01-01

    Preface All life ends in death, but perhaps one of life’s grander ironies is that it also depends on death. Cell-intrinsic suicide pathways, termed programmed cell death (PCD), are crucial for animal development, tissue homeostasis and pathogenesis. Originally, PCD was virtually synonymous with apoptosis, but recently, alternative PCD mechanisms have been reported. Here, we provide an overview of several distinct PCD mechanisms, namely apoptosis, autophagy and necroptosis. In addition, we discuss the complex signals emanating from dying cells, which can either fuel regeneration or instruct additional killing. Further advances in understanding the physiological role of multiple cell death mechanisms and associated signals will be important to selectively manipulate PCD for therapeutic purposes. PMID:25991373

  16. Ares I Operability Overview

    NASA Technical Reports Server (NTRS)

    Shaughnessy, Raymond W.

    2009-01-01

    A general overview of Ares I Operability is presented. The contents include: 1) Vehicle and Ops Concept Overviews; 2) What does operability mean to the Ares I Project?; 3) What is the Ares Project doing to influence operability into the flight hardware designs?; and 4) How do we measure Ares I Project success in infusing operability?

  17. Crew Module Overview

    NASA Technical Reports Server (NTRS)

    Redifer, Matthew E.

    2011-01-01

    The presentation presents an overview of the Crew Module development for the Pad Abort 1 flight test. The presentation describes the integration activity from the initial delivery of the primary structure through the installation of vehicle subsystems, then to flight test. A brief overview of flight test results is given.

  18. Land Remote Sensing Overview

    NASA Technical Reports Server (NTRS)

    Byrnes, Ray

    2007-01-01

    A general overview of the USGS land remote sensing program is presented. The contents include: 1) Brief overview of USGS land remote sensing program; 2) Highlights of JACIE work at USGS; 3) Update on NASA/USGS Landsat Data Continuity Mission; and 4) Notes on alternative data sources.

  19. Dying to go to school.

    PubMed

    Shearar, A

    1997-01-01

    In southern Sudan, the recent war sparked a mass migration of boys aged 5-18 who traveled through perilous terrain to the borders of Ethiopia in search of promised security and schooling. Thousands of these children died from hardships suffered in the wild, from the inadvertent or deliberate attacks of warriors, from hunger, from thirst, or from disease. Those who endured the hardships and arrived at their destination were shocked to find only military training centers or rudimentary schooling for those who were too weak or too young to be trained for battle. Eventually, the refugees were forced back into Sudan, and today about 20,000 of these unaccompanied children are displaced. Several nongovernmental organizations are running family reunification projects, and follow-up activities carried out among the reunified children reveal that they carry the scars of their trauma. The drawings the children produce as art therapy usually include the image of a young child holding a school book. While these children have a constant struggle with their memories, those who have not returned home or who have lost their families to war or disease are even more forlorn. As food rations have been halved in the refugee camps, many children are pursuing any possible alternative living arrangement. Some attempt to travel to South Africa or Egypt and some join an army in an effort to overcome the desperation of their present situation. PMID:12294200

  20. [Right to die with dignity?].

    PubMed

    Ruiz, Alvaro

    2008-06-01

    The right to die with dignity is an ill-defined concept, with multiple, often inappropriate, interpretations. The current proposition is that the physician take full responsibility for protecting the patients rights, for ensuring a rational use of resources and for overseeing the decision-making process such that the information is adequate and the steps proportioned. This responsibility extends not only to the health status of the patient situation, to the patients prognosis, and to his/her expectations and wishes, but also to the benefits foreseen and to the cost-benefit ratio. Emphasis is placed on two aspects of this relationship. First, dignity can be interpreted in many ways and sometimes, in the name of dignity, the patient is exposed (or exposes him/herself) to suffering, pain and complications that can be avoided. Second, when no reasonable probability of survival is present and a better quality of life is impossible, efforts are better redirected to offering a better quality of death. PMID:18719721

  1. [What can psychiatrists do for patients who want to die?].

    PubMed

    Okajima, Yoshiro

    2005-01-01

    The desire to commit suicide frequently arises in mentally ill patients, but how to present a persuasive argument to dissuade these patients from committing suicide remains a difficult challenge. This issue is considered below, while referring to the highly publicized Chabot case, in which a psychiatrist assisted in the suicide of a patient who was depressed by the loss of two sons under unfortunate circumstances. Euthanasia, or assisted suicide, has generally been criticized for the following reasons: 1) It is impossible to ascertain whether the free will of the patient, considered to be the fundamental basis for self-determination, was intact at the time of performing the procedure. 2) If the practice becomes widespread, then there exists the potential for vulnerable patients to receive perfunctory medical care; 3) Frequently, the desire to die is transient and ambivalent; 4) The ramifications associated with death extend beyond the individual and may be particularly acute with the family. Each of these arguments can be used as a logical counterargument to suicide, and, to the extent that they are based on the fact that death is irreversible, they are effective. However, although we are generally opposed to euthanasia and assisted suicide, we believe that these arguments are ill-suited for convincing individual patients not to commit suicide. An overview of discussions of the Chabot case is considered useful for reflecting on ways to prevent suicide, including psychotherapeutic relationships. The issue of how to respond to patients at a high risk of suicide in Japan is also considered based on these discussions. Lacking sufficient criteria for determining the competence of a patient who wants to die, the position that medical treatment can be provided simultaneously while assessing the competence of the patient is considered meaningless. In addition, there is a danger that strongly promoting the treatment of depression in patients at high risk for suicide denies

  2. Reinforced ceramic dies for superplastic forming operations

    NASA Astrophysics Data System (ADS)

    Sanders, Daniel G.

    2004-12-01

    Ceramic dies have been developed to meet the need for a dimensionally stable tool, which can withstand the temperatures (425 to 950 °C) and high forming pressures (up to 7 MPa) that are required for superplastic forming (SPF), superplastic forming with diffusion bonding (SPF/DB), and hot sizing of metal parts. With the improvements that have been made to strengthen fused silica based ceramics, the performance of ceramic tools is slowly closing in on meeting the same forming complexity as corrosion-resistant steel (CRES) dies can achieve. Boeing has successfully superplastically formed jet engine wide chord fan blades using ceramic dies, and many production aircraft parts are being built with Boeing’s patented ceramic die technology.

  3. Casting Characteristics of Aluminum Die Casting Alloys

    SciTech Connect

    Makhlouf M. Makhlouf; Diran Apelian

    2002-02-05

    The research program investigates the casting characteristics of selected aluminum die casting alloys. Specifically, the alloys' tendencies towards die soldering and sludge formation, and the alloys' fluidity and machinability are evaluated. It was found that: When the Fe and Mn contents of the alloy are low; caution has to be taken against possible die soldering. When the alloy has a high sludge factor, particularly a high level of Fe, measures must be taken to prevent the formation of large hardspots. For this kind of alloy, the Fe content should be kept at its lowest allowable level and the Mn content should be at its highest possible level. If there are problems in die filling, measures other than changing the alloy chemistry need to be considered first. In terms of alloy chemistry, the elements that form high temperature compounds must be kept at their lowest allowable levels. The alloys should not have machining problems when appropriate machining techniques and machining parameters are used.

  4. Solvent casting flow from slot die

    NASA Astrophysics Data System (ADS)

    Lee, Semi; Nam, Jaewook

    2015-11-01

    A continuous solvent casting method using a slot die can precisely control the film thickness by adjusting the operating conditions, such as the belt speed and pumping rate, not the liquid property. Therefore, it is a suitable method for high precision continuous film production. In this particular method, the dope, or casting solution, is pumped through the feed slot to form a short curtain between the die and the moving belt. Although this method is widely used in producing films for various applications, it is difficult to find indepth analyses of such flow. In this study, we developed a finite element computational model for the steady-state two-dimensional sovent casting flow from the slot die. The effect of die configurations, rheological properties and operating conditions on the behavior and shape of the gas/liquid interfaces and the location of the dynamic contact line, which is the place where the dope meets the moving belt, were investigated.

  5. Things to Do After Someone Dies

    MedlinePlus

    ... are usually hidden by clothing. What about organ donation? At some time before death or right after ... lungs, pancreas, kidneys, cornea, liver, and skin. Organ donation allows healthy organs from someone who dies to ...

  6. Geobasisdaten für die Planung?

    NASA Astrophysics Data System (ADS)

    Zölitz-Möller, Reinhard

    2002-09-01

    Die Nutzer von Geobasisdaten der Vermessungs- und Katasterverwaltungen finden heute vor allem in ATKIS (Amtliches Topographisch-Kartographisches Informationssystem) und in der ALK (automatisiert geführte Liegenschaftskarte; hier noch eingeschränkt) flächendeckende und für eine Fachdatenintegration geeignete Geodatenbestände vor. Gleichwohl wird von Nutzerseite häufig ein differenziertes und in Teilen kritisches Bild gezeichnet. Die Kritik richtet sich v.a. auf die Probleme, die ATKIS-Anwender mit dem Nutzerkomfort, dem komplexen Datenmodell, unrichtigen Flächennutzungsangaben, inkompatiblen Objektdefinitionen, den Preisen sowie mangelnder Aktualität und Vollständigkeit haben. Dennoch gibt es für viele Zwecke auch in der Planung langfristig keine echte Alternative zu den Geobasisdaten.

  7. Vehicle Technologies Program Overview

    SciTech Connect

    none,

    2006-09-05

    Overview of the Vehicle Technologies Program including external assessment and market view; internal assessment, program history and progress; program justification and federal role; program vision, mission, approach, strategic goals, outputs, and outcomes; and performance goals.

  8. Human Reliability Program Overview

    SciTech Connect

    Bodin, Michael

    2012-09-25

    This presentation covers the high points of the Human Reliability Program, including certification/decertification, critical positions, due process, organizational structure, program components, personnel security, an overview of the US DOE reliability program, retirees and academia, and security program integration.

  9. Osteoporosis: An Overview.

    ERIC Educational Resources Information Center

    Johnston, C. Conrad; Slemenda, Charles

    1987-01-01

    An overview of osteoporosis, its types, causes, diagnosis, and treatment is presented. Risk factors and bone mass measurement are also discussed. This article serves as an introduction to a symposium on osteoporosis containing five other articles in this issue. (MT)

  10. Microcomputer Technical Overview.

    ERIC Educational Resources Information Center

    Moursund, David

    1984-01-01

    A rationale for understanding computer operations is given. An overview of microcomputer technology, including an introduction to computer software, hardware, input and output devices, central processing unit, primary and secondary memory, and videodisk interactive systems is presented. (Author/BS)

  11. BIOSURFACES: A NONSCALE OVERVIEW

    EPA Science Inventory

    Biosurfaces: A Nanoscale Overview.
    Environmental surfaces (mineral, organic, biological, and composite) determine the physicochemical and biological properties of soils and control the chemical reactivity, fate, transport and transformation of nutrients and chemical contaminan...

  12. School Phobia: An Overview

    ERIC Educational Resources Information Center

    McDonald, James E.; Sheperd, George

    1976-01-01

    This article discusses general features of school phobia and specific clinical and familial traits and characteristics. Included are overviews of theoretical explanations, types of school phobia, suggested methods of treatment, and their efficacy. (Author)

  13. Overview of Alcohol Consumption

    MedlinePlus

    ... Search Alcohol & Your Health Overview of Alcohol Consumption Alcohol's Effects on the Body Alcohol Use Disorder Fetal Alcohol ... other questions about alcohol. Here’s what we know: Alcohol’s effects vary from person to person, depending on a ...

  14. Industrial storage applications overview

    NASA Technical Reports Server (NTRS)

    Duscha, R. A.

    1980-01-01

    The implementation of a technology demonstration for the food processing industry, development and technology demonstrations for selected near-term, in-plant applications and advanced industrial applications of thermal energy storage are overviewed.

  15. Machining of Silicon-Ribbon-Forming Dies

    NASA Technical Reports Server (NTRS)

    Menna, A. A.

    1985-01-01

    Carbon extension for dies used in forming silicon ribbon crystals machined precisely with help of special tool. Die extension has edges beveled toward narrow flats at top, with slot precisely oriented and centered between flats and bevels. Cutting tool assembled from standard angle cutter and circular saw or saws. Angle cutters cuts bevels while slot saw cuts slot between them. In alternative version, custom-ground edges or additional circular saws also cut flats simultaneously.

  16. Thick film silicon growth techniques. [die materials

    NASA Technical Reports Server (NTRS)

    Bates, H. E.; Mlavsky, A. I.; Jewett, D. N.; White, V. E.

    1973-01-01

    The research which was directed toward finding an improved die material is reported. Wetting experiments were conducted with various materials to determine their compatibility with silicon. Work has also continued toward the development of quartz as a die material as new techniques have provided more optimistic results than observed in the past. As a result of the thermal modification previously described, improvements in growth stability have contributed to an increase in ribbon quality.

  17. Manufacture of die casting dies by hot isostatic pressing. CRADA final report

    SciTech Connect

    Viswanathan, S.; Ren, W.; Luk, K.; Brucher, H.G.

    1998-09-01

    The reason for this Cooperative Research and Development Agreement (CRADA) between the Oak Ridge National Laboratory (ORNL) and Doehler-Jarvis was to investigate the manufacture die-casting dies with internal water-cooling lines by hot-isostatic pressing (HIPing) of H13 tool steel powder. The use of HIPing will allow the near-net-shape manufacture of dies and the strategic placement of water-cooling lines during manufacture. The production of near-net-shape dies by HIPing involves the generation of HIPing diagrams, the design of the can that can be used for HIPing a die with complex details, strategic placement of water-cooling lines in the die, computer modeling to predict movement of the water lines during HIPing, and the development of strategies for placing water lines in the appropriate locations. The results presented include a literature review, particle analysis and characterization of H13 tool steel powder, and modeling of the HIPing process.

  18. IPG Power Grid Overview

    NASA Technical Reports Server (NTRS)

    Hinke, Thomas

    2003-01-01

    This presentation will describe what is meant by grids and then cover the current state of the IPG. This will include an overview of the middleware that is key to the operation of the grid. The presentation will then describe some of the future directions that are planned for the IPG. Finally the presentation will conclude with a brief overview of the Global Grid Forum, which is a key activity that will contribute to the successful availability of grid components.

  19. TFAWS: Ares Thermal Overview

    NASA Technical Reports Server (NTRS)

    Sharp, John R.

    2007-01-01

    As part of a Constellation session at the 2007 Thermal & Fluids Analysis Workshop (TFAWS), an overview of the Crew Launch Vehicle (CLV), Crew Exploration Vehicle (CEV) and Lunar Lander systems will be given. This presentation provides a general description of the CLV (also known as Ares-I)and Ares-V vehicles portion of the session. The presentation will provide an overview of the thermal requirements, design environments, challenges and thermal modeling examples.

  20. AN OVERVIEW OF INDOOR RADON RISK REDUCTION IN THE UNITED STATES

    EPA Science Inventory

    The paper presents an overview of indoor radon risk reduction in the U.S. EPA currently estimates that 15,000-20,000 Americans die each year fromradon-induced lung cancer. his estimate is based on epidemiological data which establish the link between radon and lung cancer, and su...

  1. Celestial Fireworks from Dying Stars

    NASA Astrophysics Data System (ADS)

    2011-04-01

    This image of the nebula NGC 3582, which was captured by the Wide Field Imager on the MPG/ESO 2.2-metre telescope at ESO's La Silla Observatory in Chile, shows giant loops of gas bearing a striking resemblance to solar prominences. These loops are thought to have been ejected by dying stars, but new stars are also being born within this stellar nursery. These energetic youngsters emit intense ultraviolet radiation that makes the gas in the nebula glow, producing the fiery display shown here. NGC 3582 is part of a large star-forming region in the Milky Way, called RCW 57. It lies close to the central plane of the Milky Way in the southern constellation of Carina (The Keel of Jason's ship, the Argo). John Herschel first saw this complex region of glowing gas and dark dust clouds in 1834, during his stay in South Africa. Some of the stars forming in regions like NGC 3582 are much heavier than the Sun. These monster stars emit energy at prodigious rates and have very short lives that end in explosions as supernovae. The material ejected from these dramatic events creates bubbles in the surrounding gas and dust. This is the probable cause of the loops visible in this picture. This image was taken through multiple filters. From the Wide Field Imager, data taken through a red filter are shown in green and red, and data taken through a filter that isolates the red glow characteristic of hydrogen are also shown in red. Additional infrared data from the Digitized Sky Survey are shown in blue. The image was processed by ESO using the observational data identified by Joe DePasquale, from the United States [1], who participated in ESO's Hidden Treasures 2010 astrophotography competition [2]. The competition was organised by ESO in October-November 2010, for everyone who enjoys making beautiful images of the night sky using astronomical data obtained using professional telescopes. Notes [1] Joe searched through ESO's archive and identified datasets that he used to compose his

  2. Evolutions of Advanced Stamping CAE -- Technology Adventures and Business Impact on Automotive Dies and Stamping

    SciTech Connect

    Wang Chuantao

    2005-08-05

    In the past decade, sheet metal forming and die development has been transformed to a science-based and technology-driven engineering and manufacturing enterprise from a tryout-based craft. Stamping CAE, especially the sheet metal forming simulation, as one of the core components in digital die making and digital stamping, has played a key role in this historical transition. The stamping simulation technology and its industrial applications have greatly impacted automotive sheet metal product design, die developments, die construction and tryout, and production stamping. The stamping CAE community has successfully resolved the traditional formability problems such as splits and wrinkles. The evolution of the stamping CAE technology and business demands opens even greater opportunities and challenges to stamping CAE community in the areas of (1) continuously improving simulation accuracy, drastically reducing simulation time-in-system, and improving operationalability (friendliness) (2) resolving those historically difficult-to-resolve problems such as dimensional quality problems (springback and twist) and surface quality problems (distortion and skid/impact lines) (3) resolving total manufacturability problems in line die operations including blanking, draw/redraw, trim/piercing, and flanging, and (4) overcoming new problems in forming new sheet materials with new forming techniques. In this article, the author first provides an overview of the stamping CAE technology adventures and achievements, and industrial applications in the past decade. Then the author presents a summary of increasing manufacturability needs from the formability to total quality and total manufacturability of sheet metal stampings. Finally, the paper outlines the new needs and trends for continuous improvements and innovations to meet increasing challenges in line die formability and quality requirements in automotive stamping.

  3. Evolutions of Advanced Stamping CAE — Technology Adventures and Business Impact on Automotive Dies and Stamping

    NASA Astrophysics Data System (ADS)

    Wang, Chuantao (C. T.)

    2005-08-01

    In the past decade, sheet metal forming and die development has been transformed to a science-based and technology-driven engineering and manufacturing enterprise from a tryout-based craft. Stamping CAE, especially the sheet metal forming simulation, as one of the core components in digital die making and digital stamping, has played a key role in this historical transition. The stamping simulation technology and its industrial applications have greatly impacted automotive sheet metal product design, die developments, die construction and tryout, and production stamping. The stamping CAE community has successfully resolved the traditional formability problems such as splits and wrinkles. The evolution of the stamping CAE technology and business demands opens even greater opportunities and challenges to stamping CAE community in the areas of (1) continuously improving simulation accuracy, drastically reducing simulation time-in-system, and improving operationalability (friendliness), (2) resolving those historically difficult-to-resolve problems such as dimensional quality problems (springback and twist) and surface quality problems (distortion and skid/impact lines), (3) resolving total manufacturability problems in line die operations including blanking, draw/redraw, trim/piercing, and flanging, and (4) overcoming new problems in forming new sheet materials with new forming techniques. In this article, the author first provides an overview of the stamping CAE technology adventures and achievements, and industrial applications in the past decade. Then the author presents a summary of increasing manufacturability needs from the formability to total quality and total manufacturability of sheet metal stampings. Finally, the paper outlines the new needs and trends for continuous improvements and innovations to meet increasing challenges in line die formability and quality requirements in automotive stamping.

  4. Exploring the case for assisted dying in the UK.

    PubMed

    Haigh, Carol

    This article discusses the concepts of euthanasia, assisted suicide and physician-assisted suicide, under the umbrella term of assisted dying, from a pro-assisted dying perspective. It outlines the key principles underpinning the debate around assisted dying and refutes the main arguments put forward by those opposing legalisation of assisted dying in the UK. PMID:22272538

  5. Rapid prototyping of extrusion dies using layer-based techniques

    SciTech Connect

    Misiolek, W.Z.; Winther, K.T.; Prats, A.E.; Rock, S.J.

    1999-02-01

    Extrusion die design and development often requires significant craftsman skill and iterative improvement to arrive at a production-ready die geometry. Constructing the dies used during this iterative process from layers, rather than from one solid block of material, offers unique opportunities to improve die development efficiency when coupled with concepts drawn from the rapid prototyping field. This article presents a proof-of-concept illustrating the potential utility of layer-based extrusion dies for the die design and fabrication process. The major benefits include greater flexibility in the design process, a more efficient, automated fabrication technique, and a means for performing localized die modifications and repairs.

  6. Physics Survey Overview

    SciTech Connect

    2002-12-30

    An overview of a series of assignments of the branches of physics carried out by the Board on Physics and Astronomy of the National Research Council. It identifies further theories in physics and makes recommendations on preventive priorities. The Board on Physics and Astronomy (BPA) has conducted a new decadal survey of physics entitled ''Physics in a New Era''. The survey includes assessments of the main branches of physics as well as certain selected emerging areas. The various elements of the survey were prepared by separately-appointed National Research Council (NRC) committees. The BPA formed the Physics Survey Overview Committee (PSOVC) to complete the survey by preparing an overview of the field of physics to summarize and synthesize the results of the various assessments and to address cross-cutting issues that concern physics as a whole.

  7. State energy overview

    SciTech Connect

    Not Available

    1982-09-01

    This publication presents an overview of selected energy-related data for the United States, for each State, and for the District of Columbia. Included are the quantities of energy produced and consumed, estimates of fuel reserves, and the value of nonrenewable fuels produced by type. Also provided for each State are selected demographic and energy-related information that have been ranked and expressed as a percent of the national total. This overview provides a ready reference and a quick access to selected State energy information and State rankings for various socioeconomics and energy items.

  8. CEQATR Thermal Test Overview

    NASA Technical Reports Server (NTRS)

    Balusek, Alan R.

    2009-01-01

    A thermal test overview of the Constellation Environmental Qualification and Acceptance Test Requirement (CEQATR) is presented. The contents include: 1) CEQATR Thermal Test Overview; 2) CxP Environments; 3) CEQATR Table 1.2-1; 4) Levels of Assembly; 5) Definitions for Levels of Assembly; 6) Hardware Applicability; 7) CEQATR Thermal-Related Definitions; 8) Requirements for unit-level thermal testing; 9) Requirements for major assembly level thermal testing; 10) General thermal testing requirements; 11) General thermal cycle, thermal vacuum profiles; 12) Test tolerances; 13) Vacuum vs Ambient; 14) Thermal Gradient; 15) Sequence of Testing; 16) Alternative Strategies; 17) Protoflight; 18) Halt/Hass; 19) Humidity; and 20) Tailoring.

  9. NASA Global Hawk Overview

    NASA Technical Reports Server (NTRS)

    Naftel, Chris

    2014-01-01

    The NASA Global Hawk Project is supporting Earth Science research customers. These customers include: US Government agencies, civilian organizations, and universities. The combination of the Global Hawks range, endurance, altitude, payload power, payload volume and payload weight capabilities separates the Global Hawk platform from all other platforms available to the science community. This presentation includes an overview of the concept of operations and an overview of the completed science campaigns. In addition, the future science plans, using the NASA Global Hawk System, will be presented.

  10. EPICS system: an overview

    SciTech Connect

    Bartlett, J.F.; Bobbitt, J.S.; Kramper, B.J.; Lahey, T.E.; MacKinnon, B.A.; West, R.E.

    1984-02-01

    This paper presents an overview of the EPICS control system at FERMILAB. EPICS is a distributed, multi-user, interactive system for the control and monitoring of particle beamlines at a high-energy experimental physics laboratory. The overview discusses the operating environment of the control system, the requirements which determined the design decisions, the hardware and software configurations, and plans for the future growth and enhancement of the present system. This paper is the first of three related papers on the EPICS system. The other two cover (1) the system structure and user interface and (2) RSX implementation issues.

  11. Why do patients with lupus nephritis die?

    PubMed Central

    Correia, P; Cameron, J S; Lian, J D; Hicks, J; Ogg, C S; Williams, D G; Chantler, C; Haycock, D G

    1985-01-01

    Over 20 years 42 of 138 patients with systemic lupus erythematosus "died"--that is, suffered actual death or went into terminal renal failure, or both; data from 41 were available for analysis. In most patients the causes of death were multiple. Twenty seven patients went into terminal renal failure, of whom 25 were offered dialysis treatment. Three regained renal function later, 12 survived on dialysis or with functioning kidney allografts--almost all with inactive lupus--but 13 died after starting dialysis, most within a few weeks or months. The principal causes were active lupus or infection. In those patients with renal failure after rapid deterioration in renal function (n = 14) there were nine deaths, while of 10 patients with a slow evolution into renal failure, only four died. Four patients with impaired and 10 with normal renal function died, again most often from complications of lupus or from infection. Vascular disease was a major cause of death in seven patients, all but two of whom were young; of 15 postmortem examinations, eight showed severe coronary artery atheroma, and three surviving patients required coronary bypass operations. Analysis of the timing of death or entry into renal failure showed that in 12 out of 13 patients who died within two years of onset the lupus was judged to be active, while this was true in only eight out of 19 patients who died later. Six of the seven vascular deaths occurred later than two years from onset, while only nine of 26 renal "deaths" occurred before two years; deaths from infections (n = 13) were distributed equally. Despite this and aggressive treatment of active disease, the principal cause of actual death was uncontrolled lupus. PMID:3917713

  12. Die Europäische Union, die Europäische Gemeinschaft und ihre Rechtsordnung, die Europäische Lebensmittelkontrolle

    NASA Astrophysics Data System (ADS)

    Gallhoff, Gudrun; Rimkus, Gerhard G.

    Die Europäische Union (EU) ist ein Zusammenschluss von siebenundzwanzig unabhängigen Staaten, um deren wirtschaftliche, politische und soziale Zusammenarbeit zu verstärken. Seit 1. Mai 2007 hat sie die folgenden Mitglieder: Österreich, Belgien, Bulgarien, Dänemark, Finnland, Frankreich, Deutschland, Griechenland, Irland, Italien, Luxemburg, die Niederlande, Portugal, Spanien, Schweden, das Vereinigte Königreich von Großbritannien und Nordirland, Zypern, die Tschechische Republik, Estland, Ungarn, Lettland, Litauen, Malta, Polen, Rumänien, die Slowakei und Slowenien [1]. (Hinweis: Die Republik Zypern hat juristisch Souveränität über die ganze Insel, da die Türkische Republik Nordzypern international nicht anerkannt wird.)

  13. Die kreiselnde Büroklammer: Spielwiese

    NASA Astrophysics Data System (ADS)

    Ucke, Christian; Schlichting, Hans-Joachim

    2005-01-01

    Mit Büroklammern lassen sich einfach und schnell physikalische Experimente realisieren. Vorgestellt werden zwei ungewöhnliche Kreisel (darunter ein Stehaufkreisel), die sich in wenigen Minuten biegen lassen. Weiterhin lässt sich mit Büroklammern die schon von Leibniz abgeleitete Kettenlinie simulieren. Mit etwas Mehraufwand lässt sich eine Hängebrücke bauen, bei der sich für das Tragkabel eine Parabel als Kurvenform ergibt. Im Internet sind Programme verfügbar, mit denen sich Kettenlinie und Hängeparabel simulieren lassen.

  14. Overview of Louisville Trials

    EPA Science Inventory

    This slide presentation provides an overview of field demonstrations of condition assessment and leak detection technologies for water mains that are being conducted in Louisville, KY in cooperation with the Louisville Water Company. The project is part of the EPA Office of Rese...

  15. Strategic Investments Overview

    NASA Technical Reports Server (NTRS)

    Comstock, Doug

    2004-01-01

    This viewgraph presentation provides an overview of the organizational hierarchy for strategic management and strategic investments at NASA. The presentation also relates these topics to the budgets it submits to Congress, strategies for space exploration research and development, and systems analysis.

  16. Overview of the Volume

    NASA Technical Reports Server (NTRS)

    Dennis, Brian R.; Emslie, A. G.; Hudson, H. S.

    2011-01-01

    In this introductory chapter, we provide a brief summary of the successes and remaining challenges in understanding the solar flare phenomenon and its attendant implications for particle acceleration mechanisms in astrophysical plasmas. We also provide a brief overview of the contents of the other chapters in this volume, with particular reference to the well-observed flare of 2002 July 23.

  17. BMDO photovoltaics program overview

    NASA Technical Reports Server (NTRS)

    Caveny, Leonard H.; Allen, Douglas M.

    1994-01-01

    This is an overview of the Ballistic Missile Defense Organization (BMDO) Photovoltaic Program. Areas discussed are: (1) BMDO advanced Solar Array program; (2) Brilliant Eyes type satellites; (3) Electric propulsion; (4) Contractor Solar arrays; (5) Iofee Concentrator and Cell development; (6) Entech linear mini-dome concentrator; and (7) Flight test update/plans.

  18. Futurism 1984: An Overview.

    ERIC Educational Resources Information Center

    Hood, Florence F.

    This overview of futurism defines it as a movement believing that a positive future world may be created through wise decision-making and futuristic planning. Present societal conditions have provided an impetus for a futuristic focus, and various authors, think tanks, techniques, and organizations have contributed to the wide acclaim and respect…

  19. Overview of Infectious Diseases

    MedlinePlus

    ... Español Text Size Email Print Share Overview of Infectious Diseases Page Content Article Body I nfectious diseases are ... worms Last Updated 11/21/2015 Source Immunizations & Infectious Diseases: An Informed Parent's Guide (Copyright © 2006 American Academy ...

  20. Overview of computer vision

    SciTech Connect

    Gevarter, W.B.

    1982-09-01

    An overview of computer vision is provided. Image understanding and scene analysis are emphasized, and pertinent aspects of pattern recognition are treated. The basic approach to computer vision systems, the techniques utilized, applications, the current existing systems and state-of-the-art issues and research requirements, who is doing it and who is funding it, and future trends and expectations are reviewed.

  1. DIOXINS: AN OVERVIEW

    EPA Science Inventory

    Introduction: Dioxins have been featured in the news recently following a poisoning incident in Europe.1-3 Because physicians are not usually taught much about the dioxins, this article attempts to provide an overview for practicing physicians. Dioxins are unwanted contaminants ...

  2. LANL HED Programs Overview

    SciTech Connect

    Flippo, Kirk Adler

    2015-04-23

    The Powerpoint presentation provides an overview of High-Energy Density (HED) Physis, ICF and Burning Plasma research programs at Los Alamos National Lab. in New Mexico. Work in nuclear diagnostics is also presented, along with a summary of collaborations and upcoming projects.

  3. Overview of religions.

    PubMed

    Brooks, Nicky

    2004-01-01

    This article provides a brief overview of 9 religions: Christianity, Judaism, Jehovah's Witnesses, The Church of Jesus Christ of Latter-Day Saints, Christian Science, Islam, Hinduism, Sikhism, and Buddhism. Basic information on the origins, language, naming practices, diet, personal hygiene, and dress requirements is provided. For additional information, Web sites for each of these religions are also provided. PMID:15255273

  4. STS-51 Mission Overview

    NASA Technical Reports Server (NTRS)

    1993-01-01

    Robert Castle, Lead Flight Director, gives an overview of the STS-51 Discovery mission, including details on the Space Shuttle, the payloads (ACTS-TOS, ORFEUS-SPAS, etc.), the crew, mission objectives, and the spacewalks to be performed. Simulations of the ACT-TS deployment and the ORPFEUS-SPAS operations are shown.

  5. Performance Contracting Overview.

    ERIC Educational Resources Information Center

    Wohlferd, Gerald H.

    Conclusions reached after three years of performance contracting experience and materials with which to judge the validity of the conclusions are presented in this overview of performance contracting. The conclusions are: (1) commercial firms are no better at teaching children than are public schools; (2) commercial firms expend as much or more…

  6. An Overview of Audacity

    ERIC Educational Resources Information Center

    Thompson, Douglas Earl

    2014-01-01

    This article is an overview of the open source audio-editing and -recording program, Audacity. Key features are noted, along with significant features not included in the program. A number of music and music technology concepts are identified that could be taught and/or reinforced through using Audacity.

  7. NSI security task: Overview

    NASA Technical Reports Server (NTRS)

    Tencati, Ron

    1991-01-01

    An overview is presented of the NASA Science Internet (NSI) security task. The task includes the following: policies and security documentation; risk analysis and management; computer emergency response team; incident handling; toolkit development; user consulting; and working groups, conferences, and committees.

  8. Compton scattering overview

    SciTech Connect

    Hartemann, F V

    2008-12-01

    An overview of linear and nonlinear Compton scattering is presented, along with a comparison with Thomson scattering. Two distinct processes play important roles in the nonlinear regime: multi-photon interactions, leading to the generation of harmonics, and radiation pressure, yielding a downshift of the radiated spectral features. These mechanisms, their influence on the source brightness, and different modeling strategies are also briefly discussed.

  9. Virtual Reality: An Overview.

    ERIC Educational Resources Information Center

    Franchi, Jorge

    1994-01-01

    Highlights of this overview of virtual reality include optics; interface devices; virtual worlds; potential applications, including medicine and archaeology; problems, including costs; current research and development; future possibilities; and a listing of vendors and suppliers of virtual reality products. (Contains 11 references.) (LRW)

  10. Lead poisoning: An overview

    NASA Technical Reports Server (NTRS)

    Gendel, Neil

    1993-01-01

    A problem that should be of great concern to all of us is the lead poisoning of children. First, I would like to present a short overview concerning the reasons everyone should care about lead poisoning, then discuss the history of lead poisoning, what is happening today across the country, and the future.

  11. Effect of Die Strength and Work Piece Strength on the Wear of Hot Forging Dies

    NASA Astrophysics Data System (ADS)

    Levy, B. S.; Van Tyne, C. J.

    2015-01-01

    The effect of the strength ratio extracted from an Archard model for wear is used to describe the wear rates expected in hot forging dies. In the current study, the strength ratio is the strength of the hot forging die to the strength of the work piece. Three hot forging die steels are evaluated. The three die steels are FX, 2714, and WF. To determine the strength of the forging die, a continuous function has been developed that describes the yield strength of three die steels for temperatures from 600 to 700 °C and for times up to 20 h (i.e., tempering times of up to 20 h). The work piece material is assumed to be AISI 1045. Based on the analysis, the wear resistance of WF should be superior and FX should be slightly better than 2714. Decreasing the forging temperature increases the strength ratio, because the strength of the die surface increases faster than the flow strength of AISI 1045. The increase in the strength ratio indicates a decrease in the expected wear rate.

  12. Die casting die deflections: Prediction and attenuation. Final report, July 1, 1995--September 30, 1997

    SciTech Connect

    Miller, R.A.; Ahuett-Garza, H.; Choudhury, A.K.; Dedhia, S.

    1998-05-01

    This report summarizes two years of research intended to develop methods to model and predict the deflection patterns in die casting dies. No comprehensive analysis of this type had previously been completed. The die casting process is complex and involves numerous mechanical and thermal phenomena that effect the mechanical behavior of the die. A critical activity in this work was sorting out and evaluating the relative contributions of the various mechanisms to die deflections. This evaluation was accomplished through a series of simple engineering analyses based primarily on the order of magnitude of the influence of each load considered on die deflections. A modeling approach incorporating commercially available finite element analysis software was developed and tested. The model evolved by testing simple models against more comprehensive models and against the limited experimental data that is available. The development of the modeling approach lead to consideration of the die casting machine in more detail than was originally anticipated. The machine is critical and cannot be ignored. A simplified model described as a spring/platen model was developed to account for the machine platens, tie bars, and toggles. The characteristics of this model are described and predictions based on this model are compared against full machine models and measured deflections of machine platens. Details of the modeling approach and the various case studies are provided in the report and in several publications that have resulted from the work.

  13. Wissenschaft, die unsere Kultur verändert. Tiefenschichten des Streits um die Evolutionstheorie

    NASA Astrophysics Data System (ADS)

    Patzelt, Werner J.

    Die Evolutionstheorie ist eine der erfolgreichsten wissenschaftlichen Theorien. Sie erlaubt es, unsere Herkunft zu verstehen und riskante Merkmale gerade der menschlichen Spezies zu begreifen. Zugleich ist die Evolutionstheorie eine der umstrittensten Theorien. Das liegt nicht an ihrer empirischen Tragfähigkeit, sondern an ihrem Gegenstand. Sie handelt nämlich nicht nur - wie Hunderte andere wissenschaftliche Theorien - von der "Welt da draußen“, sondern vor allem auch von uns selbst und von unserem Platz in dieser Welt. Den einen gilt sie obendrein als Überwinderin religiösen Aberglaubens, den anderen als neuer Zugang zu Gott und seinem Wirken in der Welt. Ferner sehen die einen in der Evolution eine unbezweifelbare Tatsache gleich der Schwerkraft oder dem Holocaust, die anderen aber eine - noch oder dauerhaft - unbewiesene Hypothese oder gar eine falsche Schöpfungslehre. Und während die meisten Streitfragen solcher Art nach wechselseitig akzeptierten Regeln ‚normaler Wissenschaft‘ geklärt werden, wird bei der Frage nach dem Woher unserer Spezies und Kultur die intellektuelle Zuständigkeit von Wissenschaft mitunter überhaupt bezweifelt. Anscheinend geht es schon um recht tiefe Schichten unserer Kultur und nicht nur der wissenschaftlichen, wenn - wie seit 150 Jahren - um die Evolutionstheorie gestritten wird. Wie sehen diese Schichten aus?

  14. Investigation of Die Stress Profiles during Powder Compaction using Instrumented Die

    SciTech Connect

    Hong, Sung-tae; Hovanski, Yuri; Lavender, Curt A.; Weil, K. Scott

    2008-06-01

    The radial stress profile in a cylindrical die during compaction of titanium (Ti) powder was investigated by experiments. The concept of an instrumented die was extended to design an enhanced instrumented die. Custom-made strain gage pins were used to measure the radial stress during powder compaction. The test fixture was designed to simulate double-action pressing. The measured die stress profile for Ti powder was compared with that for a commercially available iron (Fe) powder. The stress history shows that an appreciable residual stress remains in the die in the radial direction after the axial compaction stress is removed from the powder. Furthermore, the radial stress profile in the die, while under maximum axial compaction stress, is more uniform across the height of the Fe compact than that of the Ti compact. In addition, the residual stress profile in the die in the radial direction reduces symmetrically in both directions beyond the height of the compact for both powders. Finally, the Ti powder shows a significantly higher frictional coefficient at the maximum axial compaction stress, and consequently a higher maximum axial ejection stress than the Fe powder.

  15. Cell Science-02 Payload Overview

    NASA Technical Reports Server (NTRS)

    Mitchell, Sarah Diane

    2014-01-01

    The presentation provides an general overview of the Cell Science-02 science and payload operations to the NASA Payload Operations Integrated Working Group. The overview includes a description of the science objectives and specific aims, manifest status, and operations concept.

  16. Orion Passive Thermal: Control Overview

    NASA Technical Reports Server (NTRS)

    Alvarez-Hermandez, Angel; Miller, Stephen W.

    2009-01-01

    A general overview of the NASA Orion Passive Thermal Control System (PTCS) is presented. The topics include: 1) Orion in CxP Hierarchy; 2) General Orion Description/Orientation; and 3) Orion PTCS Overview.

  17. Dying other, dying self: creating culture and meaning in palliative healthcare.

    PubMed

    McCann, Christopher J; Adames, Hector Y

    2013-08-01

    Dying is an act of creativity, and we each die as cultural beings. Culture helps us create the meaning death requests of us. However, the dominant culture of the healthcare system views death as a failure of modern medicine, an event of unspeakable terror and taboo. Palliative clinicians must honor each dying person's cultural identity (as well as the person's family), not subject it to the dominant discourse of Western medicine. This article offers practical guidelines for palliative clinicians to do so, as well as a case vignette. PMID:22854052

  18. The Hospice: Advocate for the Dying.

    ERIC Educational Resources Information Center

    Anspaugh, David J.

    1978-01-01

    The hospice philosophy seeks to meet the needs of dying patients and their families. These needs include: effective control of pain; to be loved and to alleviate loneliness; to retain dignity and maintain control of as many aspects of life as possible; and to help the family be supportive and adapt to their inevitable loss. (JMF)

  19. A profile of silicosis cases who died.

    PubMed

    Phoon, W H

    1982-01-01

    Silicosis cases which had been notified by doctors and confirmed after investigations were followed up by the Industrial Health Division. Up to August 1981, a total of 313 persons were confirmed as having the disease. Of these, 59 had died. The majority of these 59 persons had had their silica exposure in the granite quarries. 13 had been exposed to "rubber powder" which contained a high percentage of free silica. 52 of those who died were male, and their average age at death was 60.87 years. This did not appear to be significantly shorter than their life expectancy of 65.1 years. But the average age of death for the 7 women was 58.86 years, which was much shorter than their life expectancy of 70 years. Many of the men died from causes unrelated to silicosis. But 6 of the 7 women had progressive massive fibrosis (PMF) and they apparently died of the disease or complications arising from it. PMID:7073220

  20. Farewells by the Dying: A Sociological Study.

    ERIC Educational Resources Information Center

    Kellehear, Allan; Lewin, Terry

    1989-01-01

    Interviewed 100 terminally ill cancer patients to examine farewells made before the interview and those desired and planned but not yet completed. Most patients (81 percent) desired to farewell; most wanted farewell to occur late in course of their dying. Prominent in preferred styles of farewells were the gift, conversation, and letter.…

  1. Continuing Education on Dying and Death.

    ERIC Educational Resources Information Center

    Chodil, Judith J.; Dulaney, Peggy E.

    1984-01-01

    "Dying and Death in Critical Care Practice" was a one-day continuing education offering designed for registered nurses who practiced in settings such as emergency rooms, intensive care units, coronary care units, and operating rooms. The workshop was part of a continuing education curriculum in critical care nursing. (SSH)

  2. Physiknobelei Kann man die Lichtausbreitung sehen?

    NASA Astrophysics Data System (ADS)

    Schlichting, H.-Joachim

    2003-07-01

    Des Menschen Sinne sind trügerisch. Das wussten schon die Philosophen der Antike, denen physikalische Zusammenhänge noch fremd waren. Doch auch in der heutigen aufgeklärten Zeit ereignen sich noch Dinge, bei denen man seinen Augen nicht traut.

  3. Care of the Dying: A Swedish Perspective

    ERIC Educational Resources Information Center

    Feigenberg, Loma; Fulton, Robert

    1977-01-01

    This article illustrates various aspects of terminal care, and shows that rules and norms for such care do not exist today. The authors advocate the formulation of an aim for humane treatment of dying patients, and its application in a manner appropriate to Swedish medical concepts and Swedish conditions. (Author)

  4. Flexible, Ultra-Thin, Embedded Die Packaging

    NASA Astrophysics Data System (ADS)

    McPherson, Ryan J.

    As thin, flexible electronics solutions become more robust, their integration into everyday life becomes more likely. With possible applications in wearable electronics, biomedical sensors, or 'peel and stick' sensors, the reliability of these ultra-thin packages becomes paramount. Likewise, the density achievable with stacked packages benefits greatly from thinner die stacks. To this end, techniques previously developed have demonstrated packages with die thinned to approximately 20mum. Covered in this work are methods for thinning and packaging silicon die, as well as information on common materials used in these processes. The author's contribution is a fabrication process for embedding ultra-thin (approximately 10mum) silicon die in polyimide substrates. This method is fully illustrated in Chapter 3 and enumerated in the Appendix as a quick reference. Additionally, thermal cycle testing of passive daisy chain assemblies has shown promising reliability data. Packages were mounted in three alignments: flat, concave, and convex, and placed into thermal shock testing. Finally, the author discusses possible applications for this fabrication process, including the fabrication of multi-chip-modules.

  5. Asymmetric Die Grows Purer Silicon Ribbon

    NASA Technical Reports Server (NTRS)

    Kalejs, J. P.; Chalmers, B.; Surek, T.

    1983-01-01

    Concentration of carbide impurities in silicon ribbon is reduced by growing crystalline ribbon with die one wall higher than other. Height difference controls shape of meniscus at liquid/crystal interface and concentrates silicon carbide impurity near one of broad faces. Opposite face is left with above-average purity. Significantly improves efficiency of solar cells made from ribbon.

  6. Ceramic for Silicon-Shaping Dies

    NASA Technical Reports Server (NTRS)

    Sekercioglu, I.; Wills, R. R.

    1982-01-01

    Silicon beryllium oxynitride (SiBON) is a promising candidate material for manufacture of shaping dies used in fabricating ribbons or sheets of silicon. It is extremely stable, resists thermal shock, and has excellent resistance to molten silicon. SiBON is a solid solution of beryllium silicate in beta-silicon nitride.

  7. Expectation and Variation with a Virtual Die

    ERIC Educational Resources Information Center

    Watson, Jane; English, Lyn

    2015-01-01

    By the time students reach the middle years they have experienced many chance activities based on dice. Common among these are rolling one die to explore the relationship of frequency and theoretical probability, and rolling two dice and summing the outcomes to consider their probabilities. Although dice may be considered overused by some, the…

  8. [Training for working with the dying].

    PubMed

    Delisle, I

    1990-04-01

    A doctoral thesis, recently defended at the University of Caen in France, is discussed here. This descriptive study looks at the question of training individuals to accompany the dying patient, and the abilities, qualifications and skills that are required. PMID:2331671

  9. Stamping Die Making. 439-318/320.

    ERIC Educational Resources Information Center

    Yunke, P.; And Others

    Each unit in this curriculum guide on stamping die making contains an introduction, objectives, materials required, lessons, space for notes, figures, and diagrams. There are 29 units in this guide, dealing with the following topics: EZ-MILL programming; EZ-MILL BATT; print of punch and EZ-MILL part programming; download to Computer Numerical…

  10. Mold Die Making. 439-322/324.

    ERIC Educational Resources Information Center

    Yunke, P.; And Others

    Each unit in this curriculum guide on mold die making contains an introduction, objectives, materials required, lessons, space for notes, figures, and diagrams. There are 10 units in this guide: (1) introduction to Electrical Discharge Machining (EDM); (2) EDM principles; (3) the single pulse; (4) EDM safety; (5) electrode material; (6) electrode…

  11. The Onion and "When Legends Die."

    ERIC Educational Resources Information Center

    Bell, Loren C.

    1984-01-01

    Describes the eight layers in Thomas Black Bull's ("When the Legends Die") journey to spiritual rebirth and stresses that students can easily identify these layers and can thereby achieve a clearer understanding of the relationship between structure and meaning in fiction. (CRH)

  12. The Academic Study of Death and Dying.

    ERIC Educational Resources Information Center

    Amend, Edward W.

    The current study of death and dying is an example of constant change and development in academic disciplines. While the discussion of death in time of crisis is hard, if not impossible, youthful undergraduates find this topic to be of considerable interest. For them, a course can be organized effectively as a small and intimate seminar, which…

  13. Die-Attached Versus Die-Detached Resin Injection Chamber for Pultrusion

    NASA Astrophysics Data System (ADS)

    Palikhel, D. R.; Roux, J. A.; Jeswani, A. L.

    2013-02-01

    Resin injection pultrusion is an efficient and highly automated continuous process for high-quality, low-cost, high-volume manufacturing of composites. The main objective of this study is to explore the "attached-die configuration" and "detached-die configuration" for improving the resin injection pultrusion process. In this work the impact of pull speed on complete wet out of the reinforced fiber is investigated for attached-die and detached-die resin injection pultrusion with various chamber length considerations. A 3-D finite volume technique was applied to simulate the liquid resin flow through the fiber reinforcement in the injection pultrusion process. This work explores the resin injection pressure needed to achieve complete wet out and the corresponding maximum pressure inside the resin injection chamber so as to improve injection chamber design to keep the pressure within the injection chamber within reasonable constraints for different pull speeds.

  14. Hubble Space Telescope overview

    NASA Technical Reports Server (NTRS)

    Polidan, Ronald S.

    1991-01-01

    A general overview of the performance and current status of the Hubble Space Telescope is presented. Most key spacecraft subsystems are operating well, equaling or exceeding specifications. Spacecraft thermal properties, power, and communications, are superb. The only spacecraft subsystem to have failed, a gyro, is briefly discussed. All science instruments are functioning extremely well and are returning valuable scientific data. The two significant problems effecting the Hubble Space Telescope science return, the pointing jitter produced by thermally induced bending of the solar array wings and the optical telescope assembly spherical aberration, are discussed and plans to repair both problems are mentioned. The possible restoration of full optical performance of the axial scientific instruments through the use of the Corrective Optics Space Telescope Axial Replacement, currently under study for the 1993 servicing mission, is discussed. In addition, an overview of the scientific performance of the Hubble Space Telescope is presented.

  15. Paediatric anaesthesia: an overview.

    PubMed

    Langton, Helen Elizabeth

    2015-10-28

    This article provides an overview of the nursing considerations for paediatric anaesthesia. It is aimed at newly qualified operating department practitioners and anaesthetic nurses, and those with limited experience in the care of paediatric patients. It explores the ways in which paediatric anatomy and physiology differ from those of adults and looks at the implications for treatment in the anaesthetic environment. It also discusses the equipment required and the rationale for its use. PMID:26508256

  16. Scoliosis quantification: an overview

    PubMed Central

    Kawchuk, Greg; McArthur, Ross

    1997-01-01

    Scoliotic curvatures have long been a focus of attention for clinicians and research scientists alike. The study, treatment and ultimately, the prevention of this prevalent health condition are impeded by the absence of an accurate, reliable, convenient and safe method of scoliosis quantification. The purpose of this paper is to provide an overview of the current methods of scoliosis quantification for clinicians who address this condition in their practices.

  17. Overview of electric propulsion

    NASA Astrophysics Data System (ADS)

    Daniłko, Dariusz

    2014-11-01

    Space Electric Rocket Test (SERT 1) was the first experiment in which electric propulsion device was sent into space. The present year marks the 50th anniversary of that particular mission that opened the door for the application of electric propulsion on board spacecrafts. We present an overview of existing electric propulsion technology along with the description of the most successful missions that followed the success of the SERT 1mission.

  18. An overview of vortioxetine.

    PubMed

    Schatzberg, Alan F; Blier, Pierre; Culpepper, Larry; Jain, Rakesh; Papakostas, George I; Thase, Michael E

    2014-12-01

    Six clinicians provide an overview of the serotonergic antidepressant vortioxetine, which was recently approved for the treatment of major depressive disorder in adults. They discuss the pharmacologic profile and receptor-mediated effects of vortioxetine in relation to potential outcomes. Additionally, they summarize the clinical trials, which demonstrate vortioxetine's efficacy, and discuss findings related to safety and tolerability that have high relevance to patient compliance. PMID:25551236

  19. Research reactors - an overview

    SciTech Connect

    West, C.D.

    1997-03-01

    A broad overview of different types of research and type reactors is provided in this paper. Reactor designs and operating conditions are briefly described for four reactors. The reactor types described include swimming pool reactors, the High Flux Isotope Reactor, the Mark I TRIGA reactor, and the Advanced Neutron Source reactor. Emphasis in the descriptions is placed on safety-related features of the reactors. 7 refs., 7 figs., 2 tabs.

  20. Cancer Patients Who Choose to Die At Home Live Longer

    MedlinePlus

    ... suggest that doctors shouldn't hesitate to allow dying cancer patients to receive palliative care at home, ... people would like to be at home when dying, but there have been concerns about whether the ...

  1. Women Twice as Likely to Die from Severe Heart Attack

    MedlinePlus

    ... gov/medlineplus/news/fullstory_158172.html Women Twice as Likely to Die From Severe Heart Attack, Study ... 2016 (HealthDay News) -- Women are up to twice as likely as men to die from the most ...

  2. Fatigue of die cast zinc alloys

    SciTech Connect

    Schrems, K.K.; Dogan, O.N.; Goodwin, F.E.

    2006-04-01

    The rotating bending fatigue limit of die cast zinc alloy 2, alloy 3, alloy 5, AcuZinc 5, and ZA-8 were determined as a part of an on-going program by ILZRO into the mechanical properties of die cast zinc. The stress-life (S-N) curves of alloys 3, 5, AcuZinc 5, and ZA-8 were determined previously. This presentation reports the results of the S-N curve for Alloy 2 and the calculated fatigue limits for all five alloys. During the previous stress-life testing, the samples were stopped at 10 million cycles and the fatigue limit for alloy 3, alloy 5, and AcuZinc 5 appeared to be higher and the fatigue limit for ZA-8 appeared to be lower than the values reported in the literature. This was further investigated in alloy 5 and ZA-8 by testing continuous cast bulk alloy 5 and ZA-8.

  3. Spiritual aspects of death and dying.

    PubMed Central

    Mermann, A. C.

    1992-01-01

    Dying is an event beyond our comprehension, an experience that can only be imagined. Patients with cancer have a gift denied many others: some time to prepare for the approaching end of life. This time can be used to bring old conflicts to a close, to say goodbye and seek forgiveness from others, to express love and gratitude for the gifts of a life. Physicians can help patients by being aware of the spiritual dimensions to life that many patients have. In major religious traditions, death is accepted as the natural end of the gift of life and as a point of transition to another, yet unknown, existence. For many patients, it is not death that is feared, but abandonment. The physician's awareness of the spiritual needs of patients can make care of the dying more rewarding and fulfilling for all concerned. PMID:1519377

  4. Architecture for on-die interconnect

    DOEpatents

    Khare, Surhud; More, Ankit; Somasekhar, Dinesh; Dunning, David S.

    2016-03-15

    In an embodiment, an apparatus includes: a plurality of islands configured on a semiconductor die, each of the plurality of islands having a plurality of cores; and a plurality of network switches configured on the semiconductor die and each associated with one of the plurality of islands, where each network switch includes a plurality of output ports, a first set of the output ports are each to couple to the associated network switch of an island via a point-to-point interconnect and a second set of the output ports are each to couple to the associated network switches of a plurality of islands via a point-to-multipoint interconnect. Other embodiments are described and claimed.

  5. Dying in hospital: the residents' viewpoint

    PubMed Central

    Ahmedzai, S

    1982-01-01

    A survey of residents' (junior house officers') experiences and attitudes to the terminal care part of their work in four Glasgow teaching hospitals showed that even a month after starting work one-fifth of the respondents had not actively managed a dying patient. Sixty-four per cent thought that they had received inadequate teaching in terminal care. Depression and anxiety had been the most difficult symptoms encountered. The residents thought that the ward nursing staff contributed much more than their senior medical colleagues to both the medical and psychological aspects of terminal care. The results indicate a need for more undergraduate education in the most relevant areas, such as coping with the psychological problems of dying patients and their relatives. Newly qualified residents require more support from senior medical staff in looking after the terminally ill. PMID:6809204

  6. Impact of Temperature on Cooling Structural Variation of Forging Dies

    NASA Astrophysics Data System (ADS)

    Piesova, Marianna; Czan, Andrej

    2014-12-01

    The article is focused on the issue of die forging in the automotive industry. The cooling effect of temperature on the structure of forged die are under review. In the article, there is elaborated the analysis of theoretical knowledge in the field, focusing on die forging and experimentally proven effect of the cooling rate on the final structure of forged dies made of hypoeutectic carbon steel C56E2.

  7. Assisted dying - should the UK change its stance?

    PubMed

    Gordon, Daniel; Raphael, Claire E; Vassiliou, Vassilios

    2015-04-01

    Along with an increasing interest in assisted dying by many European and North American countries, some of which have already modified their existing laws to accommodate this, the interest in assisted dying in the UK has increased once again following Lord Falconer's Assisted Dying for the Terminally Ill Bill. Drawing on examples from countries where similar assisted dying laws are already in place, this article analyses and contextualises the proposed bill and discusses its potential pitfalls and benefits for the UK. PMID:25628340

  8. Japanese particle-physics leader dies

    NASA Astrophysics Data System (ADS)

    Durrani, Matin

    2008-08-01

    Yoji Totsuka, former director general of the KEK particle-physics lab in Japan, died on 10 July at the age of 66. Totsuka, whose research interests were in the field of neutrino physics, served as KEK boss for three years from April 2003. After retiring in 2006, Totsuka became a professor emeritus at KEK and the University of Tokyo. His funeral on 12 July was attended by more than 500 people.

  9. Medical futility and care of dying patients.

    PubMed Central

    Jecker, N S

    1995-01-01

    In this article, I address ethical concerns related to forgoing futile medical treatment in terminally ill and dying patients. Any discussion of medical futility should emphasize that health professionals and health care institutions have ethical responsibilities regarding medical futility. Among the topics I address are communicating with patients and families, resolving possible conflicts, and developing professional standards. Finally, I explore why acknowledging the futility of life-prolonging medical interventions can be so difficult for patients, families, and health professionals. PMID:7571593

  10. Public attitudes toward the right to die.

    PubMed Central

    Genuis, S J; Genuis, S K; Chang, W C

    1994-01-01

    OBJECTIVE: To determine public attitudes toward the right to die, euthanasia and related end-of-life decisions. DESIGN: Mail survey based on telephone numbers randomly selected by computer. SETTING: Edmonton. PARTICIPANTS: Of 1347 computer-generated, randomly selected telephone numbers called between February and June 1992, 902 individuals were reached, and 500 eligible contacts (55%) agreed to fill out the mailed questionnaire based on 12 vignettes involving end-of-life decisions. A total of 356 usable questionnaires (71%) were subsequently returned. MAIN OUTCOME MEASURES: Attitudes toward end-of-life decisions including withdrawal of life support, euthanasia, chronic suffering and the right to die, living wills and family involvement in decision making for incompetent individuals. Comments and demographic data were also solicited. RESULTS: Of the respondents 84% supported a family's right to withdraw life support from a patient in a persistent coma, and 90% supported a mentally competent patient's right to request that life support be withdrawn. Active euthanasia was supported by 65% for only patients experiencing severe pain and terminal illness. There was marked opposition to euthanasia for patients in other circumstances, such as an elderly disabled person who feels he or she is a burden on relatives (opposed by 65%), a patient with chronic depression resistant to treatment (by 75%) or an elderly person no longer satisfied with life and who has various minor physical ailments (by 83%). In all, 63% of the respondents felt that legalization of euthanasia for terminal illnesses would lead to euthanasia for many other, unsupported reasons, and 34% supported legislation to prohibit euthanasia in all situations. CONCLUSIONS: Public support for the right to die varies depending on the circumstances of the patient. The single most significant factor determining attitudes was the level of religious activity. The family's wishes were an important factor in end

  11. A Contingency Framework for Listening to the Dying

    ERIC Educational Resources Information Center

    Vora, Erika; Vora, Ariana

    2008-01-01

    Listening to the dying poses special challenges. This paper proposes a contingency framework for describing and assessing various circumstances when listening to the dying. It identifies current approaches to listening, applies the contingency framework toward effectively listening to the dying, and proposes a new type of listening called…

  12. Die and telescoping punch form convolutions in thin diaphragm

    NASA Technical Reports Server (NTRS)

    1965-01-01

    Die and punch set forms convolutions in thin dished metal diaphragm without stretching the metal too thin at sharp curvatures. The die corresponds to the metal shape to be formed, and the punch consists of elements that progressively slide against one another under the restraint of a compressed-air cushion to mate with the die.

  13. A Contextualist Thanatology: A Pragmatic Approach to Death and Dying

    ERIC Educational Resources Information Center

    Reck, Andrew J.

    1977-01-01

    Denying the value of death but accepting its reality, the author points to dying, not death, as the problematic phenomenon with which a pragmatist thanatology must deal. It is suggested that dying contains opportunities for growth--for the dying as well as for their surviving friends and relatives. (Author)

  14. 25 CFR 301.4 - Application of dies.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 25 Indians 2 2013-04-01 2013-04-01 false Application of dies. 301.4 Section 301.4 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER AND TURQUOISE PRODUCTS; STANDARDS § 301.4 Application of dies. Dies are to be applied to the object with the aid of nothing except hand...

  15. 25 CFR 301.4 - Application of dies.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 25 Indians 2 2011-04-01 2011-04-01 false Application of dies. 301.4 Section 301.4 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER AND TURQUOISE PRODUCTS; STANDARDS § 301.4 Application of dies. Dies are to be applied to the object with the aid of nothing except hand...

  16. 25 CFR 301.4 - Application of dies.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 25 Indians 2 2012-04-01 2012-04-01 false Application of dies. 301.4 Section 301.4 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER AND TURQUOISE PRODUCTS; STANDARDS § 301.4 Application of dies. Dies are to be applied to the object with the aid of nothing except hand...

  17. 25 CFR 301.4 - Application of dies.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 25 Indians 2 2014-04-01 2014-04-01 false Application of dies. 301.4 Section 301.4 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER AND TURQUOISE PRODUCTS; STANDARDS § 301.4 Application of dies. Dies are to be applied to the object with the aid of nothing except hand...

  18. 25 CFR 301.4 - Application of dies.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Application of dies. 301.4 Section 301.4 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER AND TURQUOISE PRODUCTS; STANDARDS § 301.4 Application of dies. Dies are to be applied to the object with the aid of nothing except hand...

  19. Darwin als Sehhilfe für die Psychologie - Evolutionspsychologie

    NASA Astrophysics Data System (ADS)

    Schwab, Frank

    Im Folgenden geht es um Einäugige, stereoskopisches Sehen, weite und enge Horizonte, Monokel und Sonnenbrillen. Der Beitrag versucht die Metapher des Sehens und der Sehhilfen anzuwenden, um so zu verdeutlichen, welchen Gewinn die herkömmliche Psychologie durch die Verwendung einer Darwin'schen Brille erlangen kann.

  20. A study of erosion in die casting dies by a multiple pin accelerated erosion test

    NASA Astrophysics Data System (ADS)

    Shivpuri, R.; Yu, M.; Venkatesan, K.; Chu, Y.-L.

    1995-04-01

    An accelerated erosion test was developed to evaluate the erosion resistance of die materials and coatings for die casting application. An acceleration in wear was achieved by selecting pyramid-shaped core pins, hypereutectic aluminum silicon casting alloy, high melt temperatures and high gate velocities. Multiple pin design was selected to enable multiple test sites for comparative evaluation. Apilot run was conducted on a 300 ton commercial die casting machine at various sites (pins) to verify the thermal and flow similarities. Subsequently, campaigns were run on two different 300 ton commercial die casting machines to evaluate H13 die material and different coatings for erosive resistance. Coatings and surface treatments evaluated included surface micropeening, titanium nitride, boron carbide, vanadium carbide, and metallic coatings—tungsten, molybdenum, and platinum. Recent campaigns with different melt temperatures have indicated a possible link between soldering phenomena and erosive wear. This paper presents the details of the test set up and the results of the pilot and evaluation tests.

  1. Die grünende IT - Wie die Computerindustrie das Energiesparen neu erfand

    NASA Astrophysics Data System (ADS)

    von Greiner, Wilhelm

    Die IT-Branche hat ihr grünes Gewissen entdeckt. In der jetzigen Verbreitung und Intensität ist dieses Phänomen noch recht neu - lange Zeit schien die Informationstechnik in puncto Umweltverträglichkeit und Energieverbrauch eine "weiße Weste" zu haben. Schließlich läuft ein PC mit Strom und nicht mit - sagen wir mal - einem Dieselmotor: Beim Booten eines Computers schießt nicht erst eine dunkelgraue Rauchwolke aus dem Auspuff, die Lärmerzeugung beschränkt sich auf das Surren des Lüfters, zum Tanken fahren muss man mit ihm auch nicht, und die Produktion der Komponenten erfolgt… ja, wo eigentlich? Irgendwo in der "dritten Welt", in Fernost oder in Mexiko. So sind die umweltschädlichen Aspekte der Produktion von Leiterplatten und sonstigen Bauteilen aus den Augen, aus dem Sinn und bestenfalls sporadisch Gegenstand eines kritischen Greenpeace-Berichts1, der im Überangebot der Medienlandschaft untergeht.

  2. Accurate Die Design for Automotive Panel Stamping Considering the Compensation Related with Die Deflection and Blank Thinning

    NASA Astrophysics Data System (ADS)

    Chen, Jun; Xu, Dongkai; Xia, Guodong; Li, Xifeng; Chen, Jieshi; Zhang, Jian; Yan, Wei; Li, Yue

    2011-08-01

    In order to improve assembly accuracy, automotive body panels have to be fabricated with higher dimensional and surface quality requirements, therefore the die faces should be designed more accurately to consider more relevant factors. In the presented study, we proposed algorithms to realize the following functions: through forming process simulation, the thinning distribution on the deformed blank was extracted as first kind of compensation; through die structural CAE analysis which automatically mapped the boundary contact forces onto the die surfaces from process simulation results, the die deflection was calculated as second kind of compensation. These two quantitative contributions were added together to compensate the die face. The proposed methodologies were programmed and integrated with LS-Dyna and HyperWorks, and also integrated with Autoform and CATIA linear CAE functionalities separately. In addition, a software toolkit to calculate the contacting ratio was also developed to evaluate the effectiveness of die face compensation. The second toolkit developed was verified by an automotive structural part forming die design, through die compensation and geometric optimization, the predicted contact ratio between the die face and formed blank was improved a lot, and the first toolkit was testified by a fender drawing die design. It shows that the die face compensation can be realized and integrated seamlessly between CAD model, process simulation model and die structural CAE model with the help of data I/O tools developed by the authors.

  3. Energy Saving Melting and Revert Reduction Technology (E-SMARRT): Development of Surface Engineered Coating Systems for Aluminum Pressure Die Casting Dies: Towards a 'Smart' Die Coating

    SciTech Connect

    Dr. John J. Moore; Dr. Jianliang Lin,

    2012-07-31

    The main objective of this research program was to design and develop an optimal coating system that extends die life by minimizing premature die failure. In high-pressure aluminum die-casting, the die, core pins and inserts must withstand severe processing conditions. Many of the dies and tools in the industry are being coated to improve wear-resistance and decrease down-time for maintenance. However, thermal fatigue in metal itself can still be a major problem, especially since it often leads to catastrophic failure (i.e. die breakage) as opposed to a wear-based failure (parts begin to go out of tolerance). Tooling costs remain the largest portion of production costs for many of these parts, so the ability prevent catastrophic failures would be transformative for the manufacturing industry.The technology offers energy savings through reduced energy use in the die casting process from several factors, including increased life of the tools and dies, reuse of the dies and die components, reduction/elimination of lubricants, and reduced machine down time, and reduction of Al solder sticking on the die. The use of the optimized die coating system will also reduce environmental wastes and scrap parts. Current (2012) annual energy saving estimates, based on initial dissemination to the casting industry in 2010 and market penetration of 80% by 2020, is 3.1 trillion BTU's/year. The average annual estimate of CO2 reduction per year through 2020 is 0.63 Million Metric Tons of Carbon Equivalent (MM TCE).

  4. State Energy Overview 1982

    SciTech Connect

    Not Available

    1984-08-01

    Data are presented for the 50 states and the District of Columbia. Included are the quantities of energy produced and consumed, estimates of fuel reserves, the value of nonrenewable fuels produced by type, energy expenditures, and consumer prices. Also provided for each state are selected demographic and energy-related data that have been ranked and expressed as a percent of the national total. This overview provides a ready reference and a quick access to selected state energy information and state rankings for various socioeconomic and energy items. Methodology is detailed; a glossary is provided.

  5. NREL biofuels program overview

    SciTech Connect

    Mielenz, J.R.

    1996-09-01

    The NREL Biofuels Program has been developing technology for conversion of biomass to transportation fuels with support from DOE Office of Transportation Technologies Biofuels System Program. This support has gone to both the National Renewable Energy Laboratory, and over 100 subcontractors in universities and industry. This overview will outline the value of the Biofuels development program to the Nation, the current status of the technology development, and what research areas still need further support and progress for the development of a biofuels industry in the US.

  6. Magnesium industry overview

    SciTech Connect

    Clow, B.B.

    1996-10-01

    Magnesium products provide an excellent strength-to-weight ratio, good fatigue strength, high impact strength, good corrosion resistance, high-speed machinability, and good thermal and electrical conductivities. As a result, applications are expanding in almost every industry. Dozens of automotive components are now made of magnesium, including steering wheels, valve covers, and seat frames. Magnesium alloys are also used in computer housings, in-line roller skates, golf clubs, tennis racquets, and baseball bats. Good strength and stiffness at both room and elevated temperatures make magnesium alloys especially valuable for aerospace applications. This article presents an overview of magnesium technology, world production, increasing demand, and recycling.

  7. Mined area detection overview

    NASA Astrophysics Data System (ADS)

    Burch, Ian A.; Deas, Robert M.; Port, Daniel M.

    2002-08-01

    An overview of the progress on the UK MOD Applied Research Program for Land Mine Detection. The Defense Science and Technology Laboratory (Dstl) carries out and manages the whole of the UK MOD's Mined Area Detection Applied Research Program both within its own laboratories and in partnership with industrial and academic research organizations. This paper will address two specific areas of Applied Research: hand held mine detection and vehicle mounted mine detection in support of the Mine Detection Neutralization and Route Marking System which started in April 1997. Both are multi-sensor systems, incorporating between them metal detection, ground penetrating radar, nuclear quadrupole resonance, ultra-wideband radar, and polarized thermal imaging.

  8. Overview on Peroxiredoxin.

    PubMed

    Rhee, Sue Goo

    2016-01-31

    Peroxiredoxins (Prxs) are a very large and highly conserved family of peroxidases that reduce peroxides, with a conserved cysteine residue, designated the "peroxidatic" Cys (CP) serving as the site of oxidation by peroxides (Hall et al., 2011; Rhee et al., 2012). Peroxides oxidize the CP-SH to cysteine sulfenic acid (CP-SOH), which then reacts with another cysteine residue, named the "resolving" Cys (CR) to form a disulfide that is subsequently reduced by an appropriate electron donor to complete a catalytic cycle. This overview summarizes the status of studies on Prxs and relates the following 10 minireviews. PMID:26831451

  9. Overview on Peroxiredoxin

    PubMed Central

    Rhee, Sue Goo

    2016-01-01

    Peroxiredoxins (Prxs) are a very large and highly conserved family of peroxidases that reduce peroxides, with a conserved cysteine residue, designated the “peroxidatic” Cys (CP) serving as the site of oxidation by peroxides (Hall et al., 2011; Rhee et al., 2012). Peroxides oxidize the CP-SH to cysteine sulfenic acid (CP–SOH), which then reacts with another cysteine residue, named the “resolving” Cys (CR) to form a disulfide that is subsequently reduced by an appropriate electron donor to complete a catalytic cycle. This overview summarizes the status of studies on Prxs and relates the following 10 minireviews. PMID:26831451

  10. Peanut allergens: an overview.

    PubMed

    Sáiz, Jorge; Montealegre, Cristina; Marina, Maria Luisa; García-Ruiz, Carmen

    2013-01-01

    Peanut is recognized as a potent food allergen producing one of the most frequent food allergies. This fact has originated the publication of an elevated number of scientific reports dealing with peanut allergens and, especially, the prevalence of peanut allergy. For this reason, the information available on peanut allergens is increasing and the debate about peanut allergy is always renewed. This article reviews the information currently available on peanut allergens and on the techniques used for their chemical characterization. Moreover, a general overview on the current biotechnological approaches used to reduce or eliminate peanut allergens is also provided. PMID:23638932

  11. AMPED Program Overview

    ScienceCinema

    Gur, Ilan

    2014-04-02

    An overview presentation about ARPA-E's AMPED program. AMPED projects seek to develop advanced sensing, control, and power management technologies that redefine the way we think about battery management. Energy storage can significantly improve U.S. energy independence, efficiency, and security by enabling a new generation of electric vehicles. While rapid progress is being made in new battery materials and storage technologies, few innovations have emerged in the management of advanced battery systems. AMPED aims to unlock enormous untapped potential in the performance, safety, and lifetime of today's commercial battery systems exclusively through system-level innovations, and is thus distinct from existing efforts to enhance underlying battery materials and architectures.

  12. AMPED Program Overview

    SciTech Connect

    Gur, Ilan

    2014-03-04

    An overview presentation about ARPA-E's AMPED program. AMPED projects seek to develop advanced sensing, control, and power management technologies that redefine the way we think about battery management. Energy storage can significantly improve U.S. energy independence, efficiency, and security by enabling a new generation of electric vehicles. While rapid progress is being made in new battery materials and storage technologies, few innovations have emerged in the management of advanced battery systems. AMPED aims to unlock enormous untapped potential in the performance, safety, and lifetime of today's commercial battery systems exclusively through system-level innovations, and is thus distinct from existing efforts to enhance underlying battery materials and architectures.

  13. Overview of Telepathology.

    PubMed

    Farahani, Navid; Pantanowitz, Liron

    2015-06-01

    Telepathology is the practice of remote pathology using telecommunication links to enable the electronic transmission of digital pathology images. Telepathology can be used for remotely rendering primary diagnoses, second opinion consultations, quality assurance, education, and research purposes. The use of telepathology for clinical patient care has been limited mostly to large academic institutions. Barriers that have limited its widespread use include prohibitive costs, legal and regulatory issues, technologic drawbacks, resistance from pathologists, and above all a lack of universal standards. This article provides an overview of telepathology technology and applications. PMID:26065796

  14. Overview of Telepathology.

    PubMed

    Farahani, Navid; Pantanowitz, Liron

    2016-03-01

    Telepathology is the practice of remote pathology using telecommunication links to enable the electronic transmission of digital pathology images. Telepathology can be used for remotely rendering primary diagnoses, second opinion consultations, quality assurance, education, and research purposes. The use of telepathology for clinical patient care has been limited mostly to large academic institutions. Barriers that have limited its widespread use include prohibitive costs, legal and regulatory issues, technologic drawbacks, resistance from pathologists, and above all a lack of universal standards. This article provides an overview of telepathology technology and applications. PMID:26851668

  15. Sheet metal stamping die design for warm forming

    DOEpatents

    Ghosh, Amit K.

    2003-04-22

    In metal stamping dies, by taking advantage of improved material flow by selectively warming the die, flat sections of the die can contribute to the flow of material throughout the workpiece. Local surface heating can be accomplished by placing a heating block in the die. Distribution of heating at the flat lower train central regions outside of the bend region allows a softer flow at a lower stress to enable material flow into the thinner, higher strain areas at the bend/s. The heating block is inserted into the die and is powered by a power supply.

  16. ["Good dying"--definition and current state of research].

    PubMed

    Hutter, Nico; Stößel, Ulrich; Meffert, Cornelia; Körner, Mirjam; Bozzaro, Claudia; Becker, Gerhild; Baumeister, Harald

    2015-08-01

    The advances of modern medicine did not only result in prolongation of life expectancy, but also led to a shift from dying at home to dying in public institutions. In western countries most people die at advanced age in medical facilities. Hence, the question regarding the conditions, which should be provided by society and especially medicine, to allow terminally ill people to experience "good dying" is substantial. For this purpose, an examination of patients', family members' and health care providers' understanding of the term " good dying" is required. The present paper aims at shedding light on the term "good dying" and to summarize the current state of research. Therefore, the attributes of "good dying" will be described from the perspectives of patients, family members and health care providers, which are discussed and examined in current medical-sociological research. These attributes can be illustrated on three dimensions: Quality of life at the end of life (e. g. pain relief, mental well-being), quality of dying (e. g. avoiding prolonged dying, autonomy, presence of relatives) and quality of health care at the end of life (e. g. patient-oriented health care, positive communication between health care providers and patients, availability of guidelines). Although the attributes of "good dying" are described in detail in the existing literature, further studies have to clarify the relevance and impact of these attributes as predictors of "good dying". PMID:26306020

  17. Simulation of Stamping Process of Automotive Panel Considering Die Deformation

    SciTech Connect

    Keum, Y.T.; Ahn, I.H.; Lee, I.K.; Song, M.H.; Kwon, S.O.; Park, J.S.

    2005-08-05

    In order to see the effect of die deformation on the forming of sheet metals, the draw-ins, strains, and spring-backs of an automotive fender panels are numerically simulated considering the die deformation, which is found by the simultaneous structural analysis of press and dies. By coupling the forming analysis and the structural analysis, the die deformation is simultaneously taken into account in the forming process. Furthermore, for the consideration of load difference transferred among the upper die, punch, and blank holder due to the changes in sheet thickness, the gap elements are employed instead of the blank sheet in the structural analysis. The numerical simulation results of an automotive fender draw panel are compared with the measurements. The comparison of the forming and spring-back analysis results between the rigid die and the deformed die shows that the deformed tool provides more accurate forming and spring-back prediction.

  18. DIE Deflection Modeling: Empirical Validation and Tech Transfer

    SciTech Connect

    R. Allen Miller

    2003-05-28

    This report summarizes computer modeling work that was designed to help understand how the die casting die and machine contribute to parting plane separation during operation. Techniques developed in earlier research (8) were applied to complete a large computational experiment that systematically explored the relationship between the stiffness of the machine platens and key dimensional and structural variables (platen area covered, die thickness, platen thickness, thickness of insert and the location of the die with respect to the platen) describing the die/machine system. The results consistently show that there are many significant interactions among the variables and it is the interactions, more than the individual variables themselves, which determine the performance of the machine/die system. That said, the results consistently show that it is the stiffness of the machine platens that has the largest single impact on die separation.

  19. Overview of EPIC2001

    NASA Astrophysics Data System (ADS)

    Raymond, D. J.

    2002-12-01

    The tropical eastern Pacific is a region in which coupled ocean-atmosphere climate models do a particularly poor job. In particular, the seasonal cycle is inadequately simulated in most cases. This is probably because certain physical processes are not properly represented in such models. The purpose of EPIC2001 is to develop a better understanding of key physical processes in this region with an eye to improving the associated model parameterizations. In this overview the aspects of the east Pacific which potentially can give climate models problems are outlined in the context of idealized theories of the behavior of the ocean-atmosphere system in the region. These aspects have been identified to be \\begin{itemize} the factors controlling the location and variability of east Pacific deep atmospheric convection; airmass transformations in the low-level cross-equatorial flow driven by the latitudinal sea surface temperature gradient; the effect of air-sea coupling on ocean mixed layer dynamics and SST in the east Pacific warm pool; the processes in the upper ocean that affect the structure and evolution of the shallow thermocline in this region; and dynamical, radiative, and microphysical factors affecting the energy balance in the widespread region of stratus-covered ocean south of the equator. This talk will give an overview of how the various aspects of the EPIC2001 field program are designed to address these problems and will serve as background for subsequent more specialized talks.

  20. Euthanasia, assisted dying and the right to die in Ghana: a socio-legal analysis.

    PubMed

    Owusu-Dapaa, Ernest

    2013-12-01

    There is unanimity among states to protect the continuation of life of the individual as a safeguard against their collective extinction. The right to life is accordingly guaranteed but its antithesis, the right to die is the subject of an unending debate. The controversy over the right to die is deepened by rapid advances in medicine, creating the capability for prolongation of life beyond the span which one's natural strength can endure. Ghana's supreme law explicitly guarantees the right to life but remains ambiguous on right to die, particularly euthanasia and assisted dying. Thus, some of the other rights, such as the right to dignity and not to be tortured, can creatively be exploited to justify some instances of euthanasia. Ghana's criminal code largely proscribes euthanasia. Notwithstanding, proscription of euthanasia and assisted dying by the law, in Ghana's empirical work undertaken in some of the communities in Ghana, suggests that euthanasia is quietly practisedin health facilities and private homes, especially in the rural areas. Contrary to the popular reasons assigned in the literature of the Western world, with respect to the practice or quest for legalization of euthanasia as being a necessity for providing relief from pain or hopeless quality of life, empirical data from social and anthropological studies conducted in Ghana reveal that poverty is the motivation for informal euthanasia practice in Ghana rather than genuine desire on part of patients to die or their relatives to see to their accelerated death. Apart from poverty, traditional cultural values of African societies consider non-natural death as a taboo and ignominy to the victim and his family. Thus, any move by the government to legalize euthanasia will need to be informed by widely held consultations and a possible referendum; otherwise the law may be just a mere transplant of Western models of legislation on euthanasia without reflecting the ethos of the African people. PMID:24552118

  1. Family carers providing support to a person dying in the home setting: A narrative literature review

    PubMed Central

    Morris, Sara M; King, Claire; Turner, Mary

    2015-01-01

    Background: This study is based on people dying at home relying on the care of unpaid family carers. There is growing recognition of the central role that family carers play and the burdens that they bear, but knowledge gaps remain around how to best support them. Aim: The aim of this study is to review the literature relating to the perspectives of family carers providing support to a person dying at home. Design: A narrative literature review was chosen to provide an overview and synthesis of findings. The following search terms were used: caregiver, carer, ‘terminal care’, ‘supportive care’, ‘end of life care’, ‘palliative care’, ‘domiciliary care’ AND home AND death OR dying. Data sources: During April–May 2013, Cumulative Index to Nursing and Allied Health Literature (CINAHL), MEDLINE, PsycINFO, Pubmed, Cochrane Reviews and Citation Indexes were searched. Inclusion criteria were as follows: English language, empirical studies and literature reviews, adult carers, perspectives of family carers, articles focusing on family carers providing end-of-life care in the home and those published between 2000 and 2013. Results: A total of 28 studies were included. The overarching themes were family carers’ views on the impact of the home as a setting for end-of-life care, support that made a home death possible, family carer’s views on deficits and gaps in support and transformations to the social and emotional space of the home. Conclusion: Many studies focus on the support needs of people caring for a dying family member at home, but few studies have considered how the home space is affected. Given the increasing tendency for home deaths, greater understanding of the interplay of factors affecting family carers may help improve community services. PMID:25634635

  2. 1. OVERVIEW LOOKING EAST: overview taken from south end BLDG. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    1. OVERVIEW LOOKING EAST: overview taken from south end BLDG. 1. - Fafnir Bearing Plant, Bounded on North side by Myrtle Street, on South side by Orange Street, on East side by Booth Street & on West side by Grove Street, New Britain, Hartford County, CT

  3. Models of physician-assisted dying.

    PubMed

    Girsh, F

    1996-12-01

    Repeated surveys have shown that more than 70% of Americans support physician aid in dying for terminally ill mentally competent adults. Recent polls of physicians in Oregon and Michigan demonstrate majority support of those doctors for such a law while 25% of physicians surveyed in Washington admitted to already providing help. Models of how that would work have been spelled out in proposed legislation in the United States since 1988, other models come from the Northern Territory in Australia, from Holland, and from Jack Kevorkian's writing and actions as well as from other writers such as Dr Timothy Quill. PMID:9009461

  4. When a partner dies: lesbian widows.

    PubMed

    Bent, Katherine N; Magilvy, J Kathy

    2006-06-01

    Death of a life partner and the subsequent bereavement are profound experiences for an individual. By far, the majority of bereavement research reported is focused on heterosexual couples, primarily married and often in the later years of life. The purpose of this study was to describe the bereavement experiences of lesbians whose life partners have died. The study used a descriptive, qualitative design informed by feminist scholarship and phenomenology to access the depth of personal experiences, as well as internally interpreted meanings of those experiences, among lesbian widows. PMID:16613798

  5. [From absolute necessity of dying to preventive planning of dying? The change of social and medicine debates on dying in the 1980s].

    PubMed

    Jordan, I

    2010-04-01

    International euthanasia debates focussing on "autonomous dying" in the 1980s corresponded with a general change in the health-care system: availability of new technical means with an analogous medical-ethic understanding of human suffering and dying. This change is part of a general development from "passive health consumption" to "active prevention" in our society. PMID:20229456

  6. Overview on DMD exon skipping.

    PubMed

    Aartsma-Rus, Annemieke

    2012-01-01

    Antisense-mediated exon skipping to restore the disrupted dystrophin reading frame is currently in clinical trials for Duchenne muscular dystrophy. This chapter describes the rationale of this approach and gives an overview of in vitro and in vivo experiments with antisense oligonucleotides and antisense genes. Finally, an overview of clinical trials is given and outstanding questions and hurdles are discussed. PMID:22454057

  7. Methadone Treatment: Overview and Bibliography.

    ERIC Educational Resources Information Center

    Greenfield, Lawrence; Tang, Beth Archibald

    This overview focuses on methadone treatment. Briefly, it describes the clinical uses of methadone for substance abuse treatment, explores dosage guidelines, and discusses counseling components. This overview also reviews research data on the application of methadone treatment to special populations, such as pregnant women, polydrug users, and…

  8. National Metal Casting Research Institute final report. Volume 2, Die casting research

    SciTech Connect

    Jensen, D.

    1994-06-01

    Four subprojects were completed: development and evaluation of die coatings, accelerated die life characterization of die materials, evaluation of fluid flow and solidification modeling programs, selection and characterization of Al-based die casting alloys, and influence of die materials and coatings on die casting quality.

  9. Dying, mourning, and spirituality: a psychological perspective.

    PubMed

    Marrone, R

    1999-09-01

    Based in an unfortunate tradition that stretches back in time to Watson's behaviorism and Freud's psychoanalysis, psychology has tended to reject and to pathologize matters of the spirit. In the past 30 years, however, with the advent of what has been termed the cognitive revolution, psychology has greatly expanded the scope of its subject matter. Psychologists and thanatologists have begun to unravel the cognitive underpinnings of our assumptive world and the transformation of those underpinnings in times of crisis and stress. This article examines the cognitive basis of the spiritual experience and the use of cognitive assimilation, accommodation strategies during the process of mourning the death of a loved one, as well as during the process of living our own dying. Of special importance to mental health professionals and clergy, new research on dying, mourning, and spirituality suggests that the specific ways in which people rediscover meaning--such as belief in traditional religious doctrine, the afterlife, reincarnation, philanthropy, or a spiritual order to the universe--may be less important than the process itself. In other words, in the midst of dealing with profound loss in our lives, the ability to reascribe meaning to a changed world through spiritual transformation, religious conversion, or existential change may be more significant than the specific content by which that need is filled. PMID:10558611

  10. Die-target for dynamic powder consolidation

    DOEpatents

    Flinn, J.E.; Korth, G.E.

    1985-06-27

    A die/target is disclosed for consolidation of a powder, especially an atomized rapidly solidified metal powder, to produce monoliths by the dynamic action of a shock wave, especially a shock wave produced by the detonation of an explosive charge. The die/target comprises a rectangular metal block having a square primary surface with four rectangular mold cavities formed therein to receive the powder. The cavities are located away from the geometrical center of the primary surface and are distributed around such center while also being located away from the geometrical diagonals of the primary surface to reduce the action of reflected waves so as to avoid tensile cracking of the monoliths. The primary surface is covered by a powder retention plate which is engaged by a flyer plate to transmit the shock wave to the primary surface and the powder. Spawl plates are adhesively mounted on other surfaces of the block to act as momentum traps so as to reduce reflected waves in the block. 4 figs.

  11. Die-target for dynamic powder consolidation

    DOEpatents

    Flinn, John E.; Korth, Gary E.

    1986-01-01

    A die/target is disclosed for consolidation of a powder, especially an atomized rapidly solidified metal powder, to produce monoliths by the dynamic action of a shock wave, especially a shock wave produced by the detonation of an explosive charge. The die/target comprises a rectangular metal block having a square primary surface with four rectangular mold cavities formed therein to receive the powder. The cavities are located away from the geometrical center of the primary surface and are distributed around such center while also being located away from the geometrical diagonals of the primary surface to reduce the action of reflected waves so as to avoid tensile cracking of the monoliths. The primary surface is covered by a powder retention plate which is engaged by a flyer plate to transmit the shock wave to the primary surface and the powder. Spawl plates are adhesively mounted on other surfaces of the block to act as momentum traps so as to reduce reflected waves in the block.

  12. Care of the dying adolescent: special considerations.

    PubMed

    Freyer, David R

    2004-02-01

    More than 3000 adolescents in the United States die annually from the effects of chronic illness. Providing appropriate end-of-life care for these patients is particularly challenging because of several developmental, ethical, and legal considerations relevant to this age group. Developmental issues relate to the ways in which life-threatening illness alters the normal physical and psychological changes associated with adolescence, including attainment of independence, social skills, peer acceptance, and a healthy self-image. Ethical and legal issues arise from the fact that many terminally ill adolescents <18 years of age lack ordinary legal authority to make binding medical decisions (including discontinuation of their treatment), yet they meet functional criteria for having the competence to do so. In such situations, a broad medical, ethical, and legal consensus supports giving decisional authority to the minor patient. Even when full decisional authority is not appropriate, strong moral arguments exist for taking serious account of the young adolescent's treatment preferences. In supporting the dying adolescent, an atmosphere promoting excellent communication and sound decision-making should be fostered as early as possible during preterminal care and maintained thereafter. Once palliative-care strategies become the clinical focus, psychosocial support sensitive to the adolescent's developmental stage must be provided. Using these principles, clinicians can play a crucial role in helping the adolescent, in the face of death, to experience richness of life and the dignity of self-determination. PMID:14754953

  13. [The debate about the right to die].

    PubMed

    Beca, Juan Pablo; Ortiz, Armando; Solar, Sebastián

    2005-05-01

    The Right to Die is a debatable issue and some basic notions need to be clarified to discuss it. Death needs to be recognized as part of human life. The goal of medicine is to avoid pain and alleviate suffering, to prevent premature death and when this is not possible, to let it occur peacefully. The concept of euthanasia is unclear, which increases the confusion on end-of-life topics. The term euthanasia should be used only when referring to medical acts performed to produce the patient's death, with the intention of terminating his/her suffering. It is what is usually called "active" euthanasia, which can be voluntary or involuntary. It is essential to understand the difference between producing and allowing death. This will permit timely decisions about limiting or withdrawing treatments, that can be disproportionate or that are only prolonging suffering. Limiting treatments does not mean to abandon the patient but rather to redefine his needs, such as pain treatment, prevention of complications, and relief of suffering. The ethic rationale for these decisions is the respect to the dignity of human life, and the estimation of proportionality or futility of each treatment. The physician's duty with the patient at the end of his life is to assist him in dying according to his values and to minimize his distress. PMID:15970987

  14. [Brain abscess - overview].

    PubMed

    Sveinsson, Olafur Arni; Asgeirsson, Hilmir; Olafsson, Ingvar H

    2013-01-01

    Brain abscess is a life threatening illness, demanding rapid diagnosis and treatment. Its development requires seeding of an organism into the brain parenchyma, often in an area of damaged brain tissue or in a region with poor microcirculation. The lesion evolves from a cerebritis stage to capsule formation. Brain abscesses can be caused by contiguous or haematogenous spread of an infection, or by head trauma/ neurosurgical procedure. The most common presentation is that of headache and vomiting due to raised intracranial pressure. Seizures have been reported in up to 50% of cases. Focal neurological deficits may be present, depending on the location of the lesion. Treatment of a brain abscess involves aspiration or excision, along with parenteral antibiotic therapy. The outcome has improved dramatically in the last decades due to improvement in diagnostic techniques, neurosurgery, and broad-spectrum antibiotics. The authors provide an overview of the pathogenesis, diagnosis and management of brain abscesses. PMID:23341403

  15. An Overview of Filicide

    PubMed Central

    2007-01-01

    Filicide, or the murder of one's own child, is an unfathomable crime. With Andrea Yates's return to trial in the summer of 2006, filicide once again came to the forefront of psychiatric issues in the media. One positive outcome that may be derived from this tragedy is practitioners' heightened awareness that parents may, for a variety of reasons, be compelled to kill their children. This article aims to educate mental health providers about the concept of filicide by presenting a broad overview of the topic, including a discussion of its history, definitions, classifications, outcomes, and the research surrounding it. This knowledge will hopefully bring about clinicians' increased exploration of patients' thoughts of harming their children, which may ultimately lead to the prevention of these senseless crimes. PMID:20805899

  16. Mobile radio - An overview

    NASA Astrophysics Data System (ADS)

    Kucar, Andy D.

    1991-11-01

    Following a brief prologue and historical overview, such technical issues as the repertoire of systems and services, management of the airwaves, the operating environment, service quality, network issues and cell size, channel coding and modulation, speech coding, diversity, multiplex, and multiple access (FDMA, TDMA, CDMA) are discussed. Also addressed are the potential economic and sociological impacts of mobile radio communications in the wake of the redistribution of airwaves at the World Administrative Radio Conference WARC '92. Performance dependence on multipath delay (related to the cell size and terrain configuration), Doppler frequency (related to the carrier frequency, data rate, and the speed of vehicles), and message length (can dictate the choice of multiple access) is briefly discussed.

  17. Computational Aeroacoustics: An Overview

    NASA Technical Reports Server (NTRS)

    Tam, Christopher K. W.

    2003-01-01

    An overview of recent advances in computational aeroacoustics (CAA) is presented. CAA algorithms must not be dispersive and dissipative. It should propagate waves supported by the Euler equations with the correct group velocities. Computation domains are inevitably finite in size. To avoid the reflection of acoustic and other outgoing waves at the boundaries of the computation domain, it is required that special boundary conditions be imposed at the boundary region. These boundary conditions either absorb all the outgoing waves without reflection or allow the waves to exit smoothly. High-order schemes, invariably, supports spurious short waves. These spurious waves tend to pollute the numerical solution. They must be selectively damped or filtered out. All these issues and relevant computation methods are briefly reviewed. Jet screech tones are known to have caused structural fatigue in military combat aircrafts. Numerical simulation of the jet screech phenomenon is presented as an example of a successful application of CAA.

  18. SSME Curricula: An Overview

    NASA Astrophysics Data System (ADS)

    Motta, Gianmario; Barroero, Thiago; Pignatelli, Giovanni

    Services Science (SSME) is a reality. After the 2006 manifesto published by Communications of ACM several universities are launching SSME curricula. In order to give a well founded overview of SSME and related curricula, we first address SSME scope issues. Later on we summarize the main contents of the curriculum and particularly the learning approach in the core classes. As case studies, we describe the SSME curriculum of University of Peking and University of Pavia. Finally we consider results. Graduate service engineers are designers of IT-enabled services who know how to analyze and design business service chains and to identify, customize and integrate appropriate IT modules. Differently from traditional IT engineers, service engineers use a critical value based approach with a faster and comprehensive analysis

  19. Digital radiography: an overview.

    PubMed

    Parks, Edwin T; Williamson, Gail F

    2002-11-15

    Since the discovery of X-rays in 1895, film has been the primary medium for capturing, displaying, and storing radiographic images. It is a technology that dental practitioners are the most familiar and comfortable with in terms of technique and interpretation. Digital radiography is the latest advancement in dental imaging and is slowly being adopted by the dental profession. Digital imaging incorporates computer technology in the capture, display, enhancement, and storage of direct radiographic images. Digital imaging offers some distinct advantages over film, but like any emerging technology, it presents new and different challenges for the practitioner to overcome. This article presents an overview of digital imaging including basic terminology and comparisons with film-based imaging. The principles of direct and indirect digital imaging modalities, intraoral and extraoral applications, image processing, and diagnostic efficacy will be discussed. In addition, the article will provide a list of questions dentists should consider prior to purchasing digital imaging systems for their practice. PMID:12444400

  20. Space resources. Overview

    NASA Astrophysics Data System (ADS)

    McKay, Mary Fae; McKay, David S.; Duke, Michael B.

    Space resources must be used to support life on the Moon and in the exploration of Mars. Just as the pioneers applied the tools they brought with them to resources they found along the way rather than trying to haul all their needs over a long supply line, so too must space travelers apply their high technology tools to local resources. This overview describes the findings of a study on the use of space resources in the development of future space activities and defines the necessary research and development that must precede the practical utilization of these resources. Space resources considered included lunar soil, oxygen derived from lunar soil, material retrieved from near-Earth asteroids, abundant sunlight, low gravity, and high vacuum. The study participants analyzed the direct use of these resources, the potential demand for products from them, the techniques for retrieving and processing space resources, the necessary infrastructure, and the economic tradeoffs.

  1. Tunable lasers- an overview

    SciTech Connect

    Guenther, B.D.; Buser, R.G.

    1982-08-01

    This overview of tunable lasers describes their applicability to spectroscopy in the ultraviolet and middle infrared ranges; to rapid on-line diagnostics by ultrashort cavity lasers; to exploration, by the free electron laser, for its wide tuning in the far infrared to submillimeter region; to remote detection, in areas such as portable pollution monitors, on-line chemical analyzers, auto exhaust analyzers, and production line controls; to photochemistry; and to other potential areas in diagnostics, communications, and medical and biological sciences. The following lasers are characterized by their tunability: solid state lasers, primarily alexandrite, with a tuning range of ca 1000 Angstroms; color center lasers; semiconductor lasers; dye lasers; gas lasers, where high-pressure CO/sub 2/ discharges are the best known example for a wide tunability range, and research is continuing in systems such as the alkali dimers; and, at wavelengths beyond 10 micrometers, the possibilities beyond Cerenkov and free electron lasers.

  2. Sentinel-1 Instrument Overview

    NASA Astrophysics Data System (ADS)

    Snoeij, Paul; Torres, Ramon; Geudtner, Dirk; Brown, Michael; Deghaye, Patrick; Navas-Traver, Ignacio; Ostergaard, Allan; Rommen, Bjorn; Floury, Nicolas; Davidson, Malcolm

    2013-03-01

    The forthcoming European Space Agency (ESA) Sentinel-1 (S-1) C-band SAR constellation will provide continuous all-weather day/night global coverage, with six days exact repetition time (near daily coverage over Europe and Canada) and with radar data delivery within 3 to 24 hours. These features open new possibilities for operational maritime services. The Sentinel-1 space segment has been designed and is being built by an industrial consortium with Thales Alenia Space Italia as prime contractor and EADS Astrium GmbH as C-SAR instrument responsible. It is expected that Sentinel-1A be launched in 2013. This paper will provide an overview of the Sentinel-1 system, the status and characteristics of the technical implementation. The key elements of the system supporting the maritime user community will be highlighted.

  3. SNS shielding analyses overview

    SciTech Connect

    Popova, Irina; Gallmeier, Franz; Iverson, Erik B; Lu, Wei; Remec, Igor

    2015-01-01

    This paper gives an overview on on-going shielding analyses for Spallation Neutron Source. Presently, the most of the shielding work is concentrated on the beam lines and instrument enclosures to prepare for commissioning, save operation and adequate radiation background in the future. There is on-going work for the accelerator facility. This includes radiation-protection analyses for radiation monitors placement, designing shielding for additional facilities to test accelerator structures, redesigning some parts of the facility, and designing test facilities to the main accelerator structure for component testing. Neutronics analyses are required as well to support spent structure management, including waste characterisation analyses, choice of proper transport/storage package and shielding enhancement for the package if required.

  4. Space resources. Overview

    NASA Technical Reports Server (NTRS)

    Mckay, Mary Fae (Editor); Mckay, David S. (Editor); Duke, Michael B. (Editor)

    1992-01-01

    Space resources must be used to support life on the Moon and in the exploration of Mars. Just as the pioneers applied the tools they brought with them to resources they found along the way rather than trying to haul all their needs over a long supply line, so too must space travelers apply their high technology tools to local resources. This overview describes the findings of a study on the use of space resources in the development of future space activities and defines the necessary research and development that must precede the practical utilization of these resources. Space resources considered included lunar soil, oxygen derived from lunar soil, material retrieved from near-Earth asteroids, abundant sunlight, low gravity, and high vacuum. The study participants analyzed the direct use of these resources, the potential demand for products from them, the techniques for retrieving and processing space resources, the necessary infrastructure, and the economic tradeoffs.

  5. FCS Technology Investigation Overview

    NASA Technical Reports Server (NTRS)

    Budinger, James; Gilbert, Tricia

    2007-01-01

    This working paper provides an overview of the Future Communication Study (FCS) technology investigation progress. It includes a description of the methodology applied to technology evaluation; evaluation criteria; and technology screening (down select) results. A comparison of screening results with other similar technology screening activities is provided. Additional information included in this working paper is a description of in-depth studies (including characterization of the L-band aeronautical channel; L-band deployment cost assessment; and performance assessments of candidate technologies in the applicable aeronautical channel) that have been conducted to support technology evaluations. The paper concludes with a description on-going activities leading to conclusion of the technology investigation and the development of technology recommendations.

  6. Die casting die deflections: Prediction and attenuation. Final report, July 1, 1995--September 30, 1997

    SciTech Connect

    Miller, R.Allen; Ahuett-Garza, Horacio; Choudhury, Aswin K.; Dedhia, Sanjay

    1998-05-01

    The objective of this work was to develop and test die casting design evaluation techniques based on the visualization of geometric data that is related to potential defects or problems. Specifically, thickness information is used to provide insight into potential thermal problems in the part and die. Distance from the gate and a special type of animation of the fill pattern is used to provide an assessment of gate, vent and overflow locations. Techniques have been developed to convert part design information in the form of STL files to a volume-based representation called a voxel model. The use of STL files makes the process CAD system independent. Once in voxel form, methods that were developed in this work are used to identify thick regions in the part, thin regions in the part and/or die, distance from user specified entry locations (gates), and the qualitative depiction of the fill pattern. The methods were tested with a prototype implementation on the UNIX platform. The results of comparisons with numerical simulation and field reported defects were surprisingly good. The fill-related methods were also compared against short-shots and a water analog study using high speed video. The report contains the results of the testing plus detailed background material on the construction of voxel models, the methods used for displaying results, and the computational geometric reasoning methods used to create die casting-related information from the voxel model for display to the user.

  7. Treatment-resistant major depressive disorder and assisted dying.

    PubMed

    Schuklenk, Udo; van de Vathorst, Suzanne

    2015-08-01

    Competent patients suffering from treatment-resistant depressive disorder should be treated no different in the context of assisted dying to other patients suffering from chronic conditions that render their lives permanently not worth living to them. Jurisdictions that are considering, or that have, decriminalised assisted dying are discriminating unfairly against patients suffering from treatment-resistant depression if they exclude such patients from the class of citizens entitled to receive assistance in dying. PMID:25935906

  8. 25 CFR 301.3 - Specifications of dies.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 25 Indians 2 2011-04-01 2011-04-01 false Specifications of dies. 301.3 Section 301.3 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER AND TURQUOISE PRODUCTS; STANDARDS § 301.3 Specifications of dies. Dies used are to be entirely hand-made, with no tools more mechanical than hand tools and vise....

  9. 25 CFR 304.2 - Marking and ownership of dies.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 25 Indians 2 2010-04-01 2010-04-01 false Marking and ownership of dies. 304.2 Section 304.2 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER, USE OF GOVERNMENT MARK § 304.2 Marking and ownership of dies. All dies used to mark silver will be provided by and owned by the Indian Arts and Crafts...

  10. 25 CFR 301.3 - Specifications of dies.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 25 Indians 2 2012-04-01 2012-04-01 false Specifications of dies. 301.3 Section 301.3 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER AND TURQUOISE PRODUCTS; STANDARDS § 301.3 Specifications of dies. Dies used are to be entirely hand-made, with no tools more mechanical than hand tools and vise....