Science.gov

Sample records for piezoelectric pulse gas

  1. Pulsed DC magnetron sputtered piezoelectric thin film aluminum nitride - Technology and piezoelectric properties

    NASA Astrophysics Data System (ADS)

    Stoeckel, C.; Kaufmann, C.; Hahn, R.; Schulze, R.; Billep, D.; Gessner, T.

    2014-07-01

    Pulsed DC magnetron sputtered aluminum nitride (AlN) thin films are prepared on several seed layers and at different sputtering conditions. The piezoelectric c-axis (002) orientation of the AlN is analyzed with X-ray diffraction method. The transverse piezoelectric coefficient d31 is determined with a Laser-Doppler-Vibrometer at cantilevers and membranes by analytical calculations and finite element method. Additionally, thin film AlN on bulk silicon is used to characterize the longitudinal piezoelectric charge coefficient d33.

  2. Pulsed DC magnetron sputtered piezoelectric thin film aluminum nitride – Technology and piezoelectric properties

    SciTech Connect

    Stoeckel, C. Kaufmann, C.; Hahn, R.; Schulze, R.; Billep, D.; Gessner, T.

    2014-07-21

    Pulsed DC magnetron sputtered aluminum nitride (AlN) thin films are prepared on several seed layers and at different sputtering conditions. The piezoelectric c-axis (002) orientation of the AlN is analyzed with X-ray diffraction method. The transverse piezoelectric coefficient d{sub 31} is determined with a Laser-Doppler-Vibrometer at cantilevers and membranes by analytical calculations and finite element method. Additionally, thin film AlN on bulk silicon is used to characterize the longitudinal piezoelectric charge coefficient d{sub 33}.

  3. A Skin-attachable Flexible Piezoelectric Pulse Wave Energy Harvester

    NASA Astrophysics Data System (ADS)

    Yoon, Sunghyun; Cho, Young-Ho

    2014-11-01

    We present a flexible piezoelectric generator, capable to harvest energy from human arterial pulse wave on the human wrist. Special features and advantages of the flexible piezoelectric generator include the multi-layer device design with contact windows and the simple fabrication process for the higher flexibility with the better energy harvesting efficiency. We have demonstrated the design effectiveness and the process simplicity of our skin- attachable flexible piezoelectric pulse wave energy harvester, composed of the sensitive P(VDF-TrFE) piezoelectric layer on the flexible polyimide support layer with windows. We experimentally characterize and demonstrate the energy harvesting capability of 0.2~1.0μW in the Human heart rate range on the skin contact area of 3.71cm2. Additional physiological and/or vital signal monitoring devices can be fabricated and integrated on the skin attachable flexible generator, covered by an insulation layer; thus demonstrating the potentials and advantages of the present device for such applications to the flexible multi-functional selfpowered artificial skins, capable to detect physiological and/or vital signals on Human skin using the energy harvested from arterial pulse waves.

  4. Case study of piezoelectric flexible thin films in pulse excited electromechanical transducers

    NASA Astrophysics Data System (ADS)

    Salamon, Natalia; Gozdur, Roman; Turczyński, Marcin; Lisik, Zbigniew; Soupremanien, Ulrich; Ollier, Emmanuel; Monfray, Stéphane; Skotnicki, Thomas

    2014-08-01

    The paper presents the examination of modern flexible piezoelectric thin films made of PVDF (polyvinylidene difluoride) in terms of their application in electromechanical transducers, a brief overview of available piezoelectric materials and energy harvesting devices based on piezoelectric. In order to assess the usefulness of these films from the perspective of described devices, the energy efficiency coefficient determined under the pulse excitation conditions was taken into account. Normalized volumetric efficiency ratio allows to evaluate the commercially available flexible piezoelectric films.

  5. Pulsed gas laser

    DOEpatents

    Anderson, Louis W.; Fitzsimmons, William A.

    1978-01-01

    A pulsed gas laser is constituted by Blumlein circuits wherein space metal plates function both as capacitors and transmission lines coupling high frequency oscillations to a gas filled laser tube. The tube itself is formed by spaced metal side walls which function as connections to the electrodes to provide for a high frequency, high voltage discharge in the tube to cause the gas to lase. Also shown is a spark gap switch having structural features permitting a long life.

  6. Note: A short-pulse high-intensity molecular beam valve based on a piezoelectric stack actuator

    SciTech Connect

    Abeysekera, Chamara; Joalland, Baptiste; Shi, Yuanyuan; Kamasah, Alexander; Oldham, James M.; Suits, Arthur G.

    2014-11-15

    Solenoid and piezoelectric disk valves, which are widely used to generate molecular beam pulses, still suffer from significant restrictions, such as pulse durations typically >50 μs, low repetition rates, and limited gas flows and operational times. Much of this arises owing to the limited forces these actuators can achieve. To overcome these limitations, we have developed a new pulsed valve based on a high-force piezoelectric stack actuator. We show here that operation with pulse durations as low as 20 μs and repetition rates up to 100 Hz can be easily achieved by operating the valve in conjunction with a commercial fast high-voltage switch. We outline our design and demonstrate its performance with molecular beam characterization via velocity map ion imaging.

  7. Using piezoelectric sensors for ultrasonic pulse velocity measurements in concrete

    NASA Astrophysics Data System (ADS)

    Kee, Seong-Hoon; Zhu, Jinying

    2013-11-01

    The ultrasonic pulse velocity (UPV) test has been a widely used non-destructive testing method for concrete structures. However, the conventional UPV test has limitations in consistency of results and applicability in hard-to-access regions of structures. The authors explore the feasibility of embedded piezoelectric (PZT) sensors for ultrasonic measurements in concrete structures. Two PZT sensors were embedded in a reinforced concrete specimen. One sensor worked as an actuator driven by an ultrasonic pulse-receiver, and another sensor worked as a receiver. A series of ultrasonic tests were conducted to investigate the performance of the embedded sensors in crack-free concrete and concrete specimens having a surface-breaking crack under various external loadings. Signals measured by the embedded sensors show a broad bandwidth with a centre frequency around 80 kHz, and very good coherence in the frequency range from 30 to 180 kHz. Furthermore, experimental variability in ultrasonic pulse velocity and attenuation is substantially reduced compared to previously reported values from conventional UPV equipment. Findings from this study demonstrate that the embedded sensors have great potential as a low-cost solution for ultrasonic transducers for health monitoring of concrete in structures.

  8. A piezoelectric pulse generator for low frequency non-harmonic vibration

    NASA Astrophysics Data System (ADS)

    Jiang, Hao; Yeatman, Eric M.

    2013-12-01

    This paper reports a new piezoelectric prototype for pulse generation by energy harvesting from low frequency non-harmonic vibration. The pulse generator presented here consists of two parts: the electromechanical part and the load circuit. A metal rolling rod is used as the proof mass, moving along the substrate to achieve both actuating of the piezoelectric cantilever by magnetic coupling and self-synchronous switching of the circuit. By using this new approach, the energy from the piezoelectric transduction mechanism is regulated simultaneously when it is extracted. This allows a series of tuneable pulses to be generated, which can be applied to self-powered RF wireless sensor network (WSN) nodes.

  9. Smart design selftuning piezoelectric energy harvester intended for gas turbines

    NASA Astrophysics Data System (ADS)

    Staaf, L. G. H.; Köhler, E.; Soeiro, M.; Lundgren, P.; Enoksson, P.

    2015-12-01

    Piezoelectric energy harvesting on a gas turbine implies constraints like high temperature tolerance, size limitation and a particular range of vibrations to utilise. In order to be able to operate under these conditions a harvester needs to be small and efficient and to respond to the appropriate range of frequencies. We present the design, simulation and measurements for a clamped-clamped coupled piezoelectric harvester with a free-sliding weight which adds self-tuning for improved response within the range of vibrations from the gas tufbine. We show a peak open circuit voltage of 11.7 V and a 3dB bandwidth of 12 Hz.

  10. ULTRASENSITIVE HIGH-TEMPERATURE SELECTIVE GAS DETECTION USING PIEZOELECTRIC MICROCANTILEVERS

    SciTech Connect

    Wan Y. Shih; Tejas Patil; Qiang Zhao; Yi-Shi Chiu; Wei-Heng Shih

    2004-03-05

    We have obtained very promising results in the Phase I study. Specifically, for temperature effects, we have established that piezoelectric cantilever sensors could retain their resonance peak strength at high temperatures, i.e., the Q values of the resonance peaks remained above 10 even when the temperature was very close to the Curie temperature. This confirms that a piezoelectric cantilever sensor can be used as a sensor up to its Curie temperature. Furthermore, we have shown that the mass detection sensitivity remained unchanged at different temperatures. For selective gas detection, we have demonstrated selective NH{sub 3} detection using piezoelectric cantilever sensors coated with mesoporous SiO{sub 2}. For high-temperature sensor materials development, we have achieved highly oriented Sr-doped lead titanate thin films that possessed superior dielectric and ferroelectric properties. Such highly oriented films can be microfabricated into high-performance piezoelectric microcantilever sensors that can be used up to 490 C. We have accomplished the goal of Phase I study in exploring the various aspects of a high-temperature gas sensor. We propose to continue the study in Phase II to develop a sensor that is suitable for high-temperature applications using piezoelectrics with a high Curie temperature and by controlling the effects of temperature. The lead titanate based thin film developed in Phase I is good for applications up to 490 C. In phase II, we will develop lithium niobate thin film based cantilevers for applications up to 1000 C.

  11. Measurement of a piezoelectric d constant for poly(vinylidene fluoride) transducers using pressure pulses

    NASA Astrophysics Data System (ADS)

    Bur, Anthony J.; Roth, Steven C.

    1985-01-01

    The hydrostatic piezoelectric coefficient dh has been measured for biaxially-oriented poly(vinylidene fluoride) transducers using pressure pulses having peak values of 1.8×107 Pa (2600 psi) and a pulse width of approximately 10 ms. For these measurements, the sample was placed in an oil pressure chamber at room temperature and the pressure pulse was initiated by dropping a 16-kg mass onto a plunger in the chamber. Since adiabatic compressional heating accompanies the pressure pulse, temperature compensation of the transducer was necessary. This was achieved by incorporating a thermocouple in the bilaminate configuration of the transducer and by amplifying the thermocouple signal appropriately to account for the pyroelectric response due to adiabatic heating, which was approximately 15% of the transducer signal. The calculation of dh shows that the response of the bilaminate transducer is linear up to 1.8×107 Pa (2600 psi).

  12. Piezoelectric valve

    SciTech Connect

    Petrenko, Serhiy Fedorovich

    2013-01-15

    A motorized valve has a housing having an inlet and an outlet to be connected to a pipeline, a saddle connected with the housing, a turn plug having a rod, the turn plug cooperating with the saddle, and a drive for turning the valve body and formed as a piezoelectric drive, the piezoelectric drive including a piezoelectric generator of radially directed standing acoustic waves, which is connected with the housing and is connectable with a pulse current source, and a rotor operatively connected with the piezoelectric generator and kinematically connected with the rod of the turn plug so as to turn the turn plug when the rotor is actuated by the piezoelectric generator.

  13. Quasi-static calibration of piezoelectric sensor using half-sine pressure pulse

    NASA Astrophysics Data System (ADS)

    Zhang, Qicheng; Shang, Fei; Kong, Deren

    2010-08-01

    The quasi-static method with application of half-sine pressure pulse is presented to calibrate the piezoelectric sensor, which is used for the dynamic pressure measurement of weapons. A pressure generator based on the drop hammer hydraulic system is manufactured to get the half-sine pressure pulse. The oil cylinder of the generator is reconstructed to install four standard pressure sensors and two calibrated sensors simultaneously. With pressure taken from four standard sensors as calibrating excitation, and response data obtained from calibrated sensors, the working sensitivities of sensors are worked out through regression analysis. The experimental results obtained with sensor 6215 at the national shooting range shows that it is effective to calibrate piezoelectric sensors using half-sine pressure pulse. The residual standard deviation of the equation fitting is less than 0.7%; the linearity is less than 0.21%; and the relative uncertainty of the four standard sensors is less than 0.7%, under the precision target of the calibration system acceptance.

  14. Development of lead-free piezoelectric thin films by pulsed laser deposition

    NASA Astrophysics Data System (ADS)

    Abazari Torghabeh, Maryam

    As a high performance piezoelectric material widely used in sensors, actuators and other electronic devices, lead zirconate titanate (PZT) ceramics have been the center of attention for many years. However, the toxicity of these materials and their exposure to the environment during processing steps, such as calcination, sintering, machining as well as problems in recycling and disposal have been major concerns regarding their usage all around the globe for the past couple of decades. Consequently, utilizing lead-based materials for many commercial applications have been recently restricted in Europe and Asia and measures are being taken in United States as well. Therefore, there is an urgent need for lead-free piezoelectrics whose properties are comparable to those of well-known PZT materials. Recently, the discovery of ultra-high piezoelectric activity in the ternary lead-free KNaNbO3-LiTaO 3-LiSbO3 (KNN-LT-LS) and (Bi,Na)TiO3-(Bi,K)TiO 3-BaTiO3 (BNT-BKT-BT) systems have given hope for alternatives to PZT. Furthermore, the demand for new generation of environment-friendly functional devices, utilizing piezoelectric materials, inspired a new surge in lead-free piezoelectric thin film research. In this study, an attempt has been made to explore the development of lead-free piezoelectric thin films by Pulsed Laser Deposition (PLD) on SrTiO 3 substrate. While the growth and development process of KNN-LT-LS thin films was the primary goal of this thesis, a preliminary effort was also made to fabricate and characterize BNT-BKT-BT thin films. In a comprehensive and systematic process optimization study in conjunction with X-ray diffractometry, the phase evolution, stoichiometry, and growth orientation of the films are monitored as a function of deposition conditions including temperature and ambient oxygen partial pressure. Processing parameters such as substrate temperature and pressure are shown to be highly dominant in determining the phase and composition of the

  15. Nonlinear magnetoelectric response of planar ferromagnetic-piezoelectric structures to sub-millisecond magnetic pulses.

    PubMed

    Kreitmeier, Florian; Chashin, Dmitry V; Fetisov, Yury K; Fetisov, Leonid Y; Schulz, Irene; Monkman, Gareth J; Shamonin, Mikhail

    2012-01-01

    The magnetoelectric response of bi- and symmetric trilayer composite structures to pulsed magnetic fields is experimentally investigated in detail. The structures comprise layers of commercially available piezoelectric (lead zirconate titanate) and magnetostrictive (permendur or nickel) materials. The magnetic-field pulses have the form of a half-wave sine function with duration of 450 µs and amplitudes ranging from 500 Oe to 38 kOe. The time dependence of the resulting voltage is presented and explained by theoretical estimations. Appearance of voltage oscillations with frequencies much larger than the reciprocal pulse length is observed for sufficiently large amplitudes (~1-10 kOe) of the magnetic-field pulse. The origin of these oscillations is the excitation of bending and planar acoustic oscillations in the structures. Dependencies of the magnetoelectric voltage coefficient on the excitation frequency and the applied magnetic field are calculated by digital signal processing and compared with those obtained by the method of harmonic field modulation. The results are of interest for developing magnetoelectric sensors of pulsed magnetic fields as well as for rapid characterization of magnetoelectric composite structures. PMID:23202188

  16. Nonlinear Magnetoelectric Response of Planar Ferromagnetic-Piezoelectric Structures to Sub-Millisecond Magnetic Pulses

    PubMed Central

    Kreitmeier, Florian; Chashin, Dmitry V.; Fetisov, Yury K.; Fetisov, Leonid Y.; Schulz, Irene; Monkman, Gareth J.; Shamonin, Mikhail

    2012-01-01

    The magnetoelectric response of bi- and symmetric trilayer composite structures to pulsed magnetic fields is experimentally investigated in detail. The structures comprise layers of commercially available piezoelectric (lead zirconate titanate) and magnetostrictive (permendur or nickel) materials. The magnetic-field pulses have the form of a half-wave sine function with duration of 450 μs and amplitudes ranging from 500 Oe to 38 kOe. The time dependence of the resulting voltage is presented and explained by theoretical estimations. Appearance of voltage oscillations with frequencies much larger than the reciprocal pulse length is observed for sufficiently large amplitudes (∼1–10 kOe) of the magnetic-field pulse. The origin of these oscillations is the excitation of bending and planar acoustic oscillations in the structures. Dependencies of the magnetoelectric voltage coefficient on the excitation frequency and the applied magnetic field are calculated by digital signal processing and compared with those obtained by the method of harmonic field modulation. The results are of interest for developing magnetoelectric sensors of pulsed magnetic fields as well as for rapid characterization of magnetoelectric composite structures. PMID:23202188

  17. Optimal placement of piezoelectric plates for active vibration control of gas turbine blades: experimental results

    NASA Astrophysics Data System (ADS)

    Botta, F.; Marx, N.; Gentili, S.; Schwingshackl, C. W.; Di Mare, L.; Cerri, G.; Dini, D.

    2012-04-01

    It is well known that the gas turbine blade vibrations can give rise to catastrophic failures and a reduction of the blades life because of fatigue related phenomena[1]-[3] . In last two decades, the adoption of piezoelectric elements, has received considerable attention by many researcher for its potential applicability to different areas of mechanical, aerospace, aeronautical and civil engineering. Recently, a number of studies of blades vibration control via piezoelectric plates and patches have been reported[4]-[6] . It was reported that the use of piezoelectric elements can be very effective in actively controlling vibrations. In one of their previous contributions[7] , the authors of the present manuscript studied a model to control the blade vibrations by piezoelectric elements and validated their results using a multi-physics finite elements package (COMSOL) and results from the literature. An optimal placement method of piezoelectric plate has been developed and applied to different loading scenarios for realistic configurations encountered in gas turbine blades. It has been demonstrated that the optimal placement depends on the spectrum of the load, so that segmented piezoelectric patches have been considered and, for different loads, an optimal combination of sequential and/or parallel actuation and control of the segments has been studied. In this paper, an experimental investigation carried out by the authors using a simplified beam configuration is reported and discussed. The test results obtained by the investigators are then compared with the numerical predictions [7] .

  18. Pressure wave charged repetitively pulsed gas laser

    DOEpatents

    Kulkarny, Vijay A.

    1982-01-01

    A repetitively pulsed gas laser in which a system of mechanical shutters bracketing the laser cavity manipulate pressure waves resulting from residual energy in the cavity gas following a lasing event so as to draw fresh gas into the cavity and effectively pump spent gas in a dynamic closed loop.

  19. Waveguide piezoelectric micromachined ultrasonic transducer array for short-range pulse-echo imaging

    NASA Astrophysics Data System (ADS)

    Lu, Y.; Tang, H.; Wang, Q.; Fung, S.; Tsai, J. M.; Daneman, M.; Boser, B. E.; Horsley, D. A.

    2015-05-01

    This paper presents an 8 × 24 element, 100 μm-pitch, 20 MHz ultrasound imager based on a piezoelectric micromachined ultrasonic transducer (PMUT) array having integrated acoustic waveguides. The 70 μm diameter, 220 μm long waveguides function both to direct acoustic waves and to confine acoustic energy, and also to provide mechanical protection for the PMUT array used for surface-imaging applications such as an ultrasonic fingerprint sensor. The imager consists of a PMUT array bonded with a CMOS ASIC using wafer-level conductive eutectic bonding. This construction allows each PMUT in the array to have a dedicated front-end receive amplifier, which together with on-chip analog multiplexing enables individual pixel read-out with high signal-to-noise ratio through minimized parasitic capacitance between the PMUT and the front-end amplifier. Finite element method simulations demonstrate that the waveguides preserve the pressure amplitude of acoustic pulses over distances of 600 μm. Moreover, the waveguide design demonstrated here enables pixel-by-pixel readout of the ultrasound image due to improved directivity of the PMUT by directing acoustic waves and creating a pressure field with greater spatial uniformity at the end of the waveguide. Pulse-echo imaging experiments conducted using a one-dimensional steel grating demonstrate the array's ability to form a two-dimensional image of a target.

  20. Means for positively seating a piezoceramic element in a piezoelectric valve during inlet gas injection

    DOEpatents

    Wright, Kenneth E.

    1994-01-01

    A piezoelectric valve in a gas delivery system includes a piezoceramic element bonded to a valve seal and disposed over a valve seat, and retained in position by an O-ring and a retainer; an insulating ball normally biased by a preload spring against the piezoceramic element; an inlet gas port positioned such that upon admission of inlet gas into the valve, the piezoceramic element is positively seated. The inlet gas port is located only on the side of the piezoceramic element opposite the seal.

  1. Means for positively seating a piezoceramic element in a piezoelectric valve during inlet gas injection

    DOEpatents

    Wright, K.E.

    1994-08-23

    A piezoelectric valve in a gas delivery system includes a piezoceramic element bonded to a valve seal and disposed over a valve seat, and retained in position by an O-ring and a retainer; an insulating ball normally biased by a preload spring against the piezoceramic element; an inlet gas port positioned such that upon admission of inlet gas into the valve, the piezoceramic element is positively seated. The inlet gas port is located only on the side of the piezoceramic element opposite the seal. 3 figs.

  2. A means for positively seating a piezoceramic element in a piezoelectric valve during inlet gas injection

    SciTech Connect

    Wright, K.E.

    1993-12-31

    This invention is comprised of a piezoelectric valve in a gas delivery system which includes a piezoceramic element bonded to a valve seal and disposed over a valve seat, and retained in position by an O-ring and a retainer; and insulating ball normally biased by a preload spring against the piezoceramic element; and inlet gas port positioned such that upon admission of inlet gas into the valve. The piezoceramic element is positively seated. The inelt gas port is located only on the side of the piezoceramic element opposite the seal.

  3. Influence of oxygen concentration in sputtering gas on piezoelectric response of aluminum nitride thin films

    SciTech Connect

    Akiyama, Morito; Kamohara, Toshihiro; Kano, Kazuhiko; Teshigahara, Akihiko; Kawahara, Nobuaki

    2008-07-14

    The authors have investigated the influence of oxygen concentration in sputtering gas on the piezoelectric response of aluminum nitride (AlN) thin films prepared on silicon substrates. The piezoelectric response strongly depends on the oxygen concentration, and changes from +6.8 to -7.0 pC/N with increasing oxygen concentration from 0% to 1.2%. The polar direction drastically inverts from the Al polarity to N polarity. When the oxygen concentration in sputtering gas was 1.2%, the oxygen concentration in the AlN films was 7 at. %. Furthermore, the growth rate of the AlN films gradually decreases with increasing oxygen concentration in sputtering gas.

  4. High Power Pulsed Gas Lasers

    NASA Astrophysics Data System (ADS)

    Witteman, W. J.

    1987-09-01

    Gas lasers have shown to be capable of delivering tens of terrawatt aspeak power or tens of kilowatt as average power. The efficiencies of most high power gas lasers are relatively high compared with other types of lasers. For instance molecular lasers, oscillating on low lying vibrational levels, and excimer lasers may have intrinsic efficiencies above 10%.The wavelengths of these gas lasers cover the range from the far infrared to the ultra-violet region, say from 12000 to 193 nm. The most important properties are the scalability, optical homogeneity of the excited medium, and the relatively low price per watt of output power. The disadvantages may be the large size of the systems and the relatively narrow line width with limited tunability compared with solid state systems producing the same peak power. High power gas lasers group into three main categories depending on the waste-heat handling capacity.

  5. Development of Long-Lifetime Pulsed Gas Valves for Pulsed Electric Thrusters

    NASA Technical Reports Server (NTRS)

    Burkhardt, Wendel M.; Crapuchettes, John M.; Addona, Brad M.; Polzin, Kurt A.

    2015-01-01

    even 10(exp 9) cycles is well above anything demonstrated, this lower value was selected as the design point for the present work. The valve seal must remain leak-tight throughout operation, and the body must maintain a low internal leakage at relatively high operating temperatures. The full set of design requirements used for this program are summarized in Table 1. In this work, we describe two pulsed gas valves that have been fabricated to have long lifetime and demonstrate the characteristics listed above. The first is a miniaturized, conventional electromagnet-based valve while the second is a piezoelectric-based valve design. The conventional valve, shown in Fig. 1, is opened by use of a solenoid electromagnetic actuator. When current is applied to the solenoid coil, magnetic forces pull the plunger away from the valve seat, allowing fluid to flow through the valve. Removal of electrical current permits the spring and fluid pressure to seat the plunger, halting the flow of fluid. The valve body is fabricated from 304L corrosion resistant steel (CRES) and while the parts that form the magnetic circuit are fabricated from 430 CRES. This material does not have optimum magnetic properties, but its corrosion resistance permits incorporation into a design without requiring an additional plating process. A viton O-ring compound (Parker V0884-75), selected for its mechanical strength at elevated temperatures, was used for the valve seat seal. The design was based solely on the use of analytical sizing calculations, as opposed to a more rigorous finite element analysis. While this valve is small and relatively lightweight, it does not represent a design that is optimized for mass and/or a given volume envelope. The piezoelectric valve is a "puller" valve design. Applying a voltage to the piezo crystal causes it to elongate and pull a pintle off the seat, opening the valve. The valve seal consists of the pintle with an external, spherically-formed tip fabricated from

  6. Inductive gas line for pulsed lasers

    DOEpatents

    Benett, William J.; Alger, Terry W.

    1985-01-01

    A gas laser having a metal inlet gas feed line assembly shaped as a coil, to function as an electrical inductance and therefore high impedance to pulses of electric current applied to electrodes at opposite ends of a discharge tube of a laser, for example. This eliminates a discharge path for the laser through the inlet gas feed line. A ferrite core extends through the coil to increase the inductance of the coil and provide better electric isolation. By elimination of any discharge breakdown through the gas supply, efficiency is increased and a significantly longer operating lifetime of the laser is provided.

  7. Inductive gas line for pulsed lasers

    DOEpatents

    Benett, W.J.; Alger, T.W.

    1982-09-29

    A gas laser having a metal inlet gas feed line assembly shaped as a coil, to function as an electrical inductance and therefore high impedance to pulses of electric current applied to electrodes at opposite ends of a discharge tube of a laser, for example. This eliminates a discharge path for the laser through the inlet gas feed line. A ferrite core extends through the coil to increase the inductance of the coil and provide better electric isolation. By elimination of any discharge breakdown through the gas supply, efficiency is increased and a significantly longer operating lifetime of the laser is provided.

  8. Detection of laser-induced nanosecond ultrasonic pulses in metals using a pancake coil and a piezoelectric sensor.

    PubMed

    Kozhushko, Victor V; Krenn, Heinz

    2012-06-01

    A piezoelectric sensor and a pancake coil sensor were used for broadband detection of laser-induced ultrasound in single-crystal aluminum and polycrystalline nickel. Pressure pulses with pronounced compression phases were induced by laser pulses of 5 ns duration from one side of the specimens and detected from the opposite side. A coupling layer of water was required for the piezoelectric method, whereas the pancake coil placed in the biasing permanent field of a cylindrical magnet ~0.25 T allowed noncontact detection. The signals detected by a piezoelectric transducer showed bipolar form and their spectra covered the range from 5 to 90 MHz. The signal measured in aluminum by a pancake coil was assigned to the eddy current sources and had single polarity. The peak-to-peak value of the signal in nickel was higher and had bipolar form because of the inverse magnetostrictive effect. The high-frequency limit detected by the pancake coil approached 200 MHz. PMID:22718873

  9. Piezoelectric transformers for low-voltage generation of gas discharges and ionic winds in atmospheric air

    SciTech Connect

    Johnson, Michael J.; Go, David B.

    2015-12-28

    To generate a gas discharge (plasma) in atmospheric air requires an electric field that exceeds the breakdown threshold of ∼30 kV/cm. Because of safety, size, or cost constraints, the large applied voltages required to generate such fields are often prohibitive for portable applications. In this work, piezoelectric transformers are used to amplify a low input applied voltage (<30 V) to generate breakdown in air without the need for conventional high-voltage electrical equipment. Piezoelectric transformers (PTs) use their inherent electromechanical resonance to produce a voltage amplification, such that the surface of the piezoelectric exhibits a large surface voltage that can generate corona-like discharges on its corners or on adjacent electrodes. In the proper configuration, these discharges can be used to generate a bulk air flow called an ionic wind. In this work, PT-driven discharges are characterized by measuring the discharge current and the velocity of the induced ionic wind with ionic winds generated using input voltages as low as 7 V. The characteristics of the discharge change as the input voltage increases; this modifies the resonance of the system and subsequent required operating parameters.

  10. Piezoelectric transformers for low-voltage generation of gas discharges and ionic winds in atmospheric air

    NASA Astrophysics Data System (ADS)

    Johnson, Michael J.; Go, David B.

    2015-12-01

    To generate a gas discharge (plasma) in atmospheric air requires an electric field that exceeds the breakdown threshold of ˜30 kV/cm. Because of safety, size, or cost constraints, the large applied voltages required to generate such fields are often prohibitive for portable applications. In this work, piezoelectric transformers are used to amplify a low input applied voltage (<30 V) to generate breakdown in air without the need for conventional high-voltage electrical equipment. Piezoelectric transformers (PTs) use their inherent electromechanical resonance to produce a voltage amplification, such that the surface of the piezoelectric exhibits a large surface voltage that can generate corona-like discharges on its corners or on adjacent electrodes. In the proper configuration, these discharges can be used to generate a bulk air flow called an ionic wind. In this work, PT-driven discharges are characterized by measuring the discharge current and the velocity of the induced ionic wind with ionic winds generated using input voltages as low as 7 V. The characteristics of the discharge change as the input voltage increases; this modifies the resonance of the system and subsequent required operating parameters.

  11. Piezoelectric Electromechanical Coupling in Nanomechanical Resonators with a Two-Dimensional Electron Gas

    NASA Astrophysics Data System (ADS)

    Shevyrin, A. A.; Pogosov, A. G.; Bakarov, A. K.; Shklyaev, A. A.

    2016-07-01

    The electrical response of a two-dimensional electron gas to vibrations of a nanomechanical cantilever containing it is studied. Vibrations of perpendicularly oriented cantilevers are experimentally shown to oppositely change the conductivity near their bases. This indicates the piezoelectric nature of electromechanical coupling. A physical model is developed, which quantitatively explains the experiment. It shows that the main origin of the conductivity change is a rapid change in the mechanical stress on the boundary between suspended and nonsuspended areas, rather than the stress itself.

  12. Piezoelectric Electromechanical Coupling in Nanomechanical Resonators with a Two-Dimensional Electron Gas.

    PubMed

    Shevyrin, A A; Pogosov, A G; Bakarov, A K; Shklyaev, A A

    2016-07-01

    The electrical response of a two-dimensional electron gas to vibrations of a nanomechanical cantilever containing it is studied. Vibrations of perpendicularly oriented cantilevers are experimentally shown to oppositely change the conductivity near their bases. This indicates the piezoelectric nature of electromechanical coupling. A physical model is developed, which quantitatively explains the experiment. It shows that the main origin of the conductivity change is a rapid change in the mechanical stress on the boundary between suspended and nonsuspended areas, rather than the stress itself. PMID:27419592

  13. Application of amplified piezoelectric actuators to the construction of gas valves

    NASA Astrophysics Data System (ADS)

    Bouchilloux, Philippe; Le Letty, Ronan; Lhermet, Nicolas; Patient, G.; Claeyssen, Frank; Lang, M.

    2003-08-01

    In past years, Amplified Piezoelectric Actuators (APA) have been applied to a variety of industrial applications that take advantage of their quick response and precise positioning capabilities. More recently, APA's have been integrated into valve designs to obtain both rapid and precise proportional flow control. This paper presents the design and measurement results of two gas valves that have recently been developed. The first gas valve uses a small APA that is driven by a switching amplifier to obtain a high frequency modulation. A frequency modulation higher than 400Hz, along with a stroke of 100μm, have been measured. These results show that such a design could be applied to fuel injection systems. The second gas valve is also based on an APA. It includes a linear amplifier and a servo controller to obtain an accurate proportional response dedicated to precise gas flow control. Such valves are interesting for instrumentation and space applications, where they can provide a linear and stable flow control. The low power consumption of the piezoelectric valve in space applications is an additional advantage. A stable flow of dry nitrogen ranging from 0.1sccm to 200sccm has been measured with an inlet pressure of 1bar. A variety of modeling tools has been used to design these valves: finite element modeling for the electro-mechanical aspects and for the contact mechanics between the poppet and the seat, as well as computational fluid dynamics for the flow simulation. These tools make it possible to modify the valve design in order to meet different requirements and serve other applications.

  14. Study of the characteristics of a piezoelectric lead zirconate titanate radiation detector using a pulsed xenon source

    SciTech Connect

    Miyachi, Takashi; Fujii, Masayuki; Hasebe, Nobuyuki; Okudaira, Osamu; Takechi, Seiji; Kurozumi, Atsuma; Morinaga, Shinya; Uno, Takefumi; Shibata, Hiromi; Kobayashi, Masanori; Murakami, Takeshi; Uchihori, Yukio; Okada, Nagaya

    2010-05-15

    The detector characteristics of piezoelectric lead zirconate titanate (PZT) were studied by directly irradiating a multilayered PZT detector with 400 MeV/n xenon ions. An extracted beam was processed with a rotating slit. Thus, passed through {approx}10{sup 3} xenon ions were available for 50 to 250 {mu}s. The effect of polarization on the output signal was discussed, and the optimal electrode configuration was determined. The output signal appeared as an isolated pulse whose amplitude was qualitatively understood by the Bethe-Bloch formula. However, the calculated and the observed values differed depending on the rotation speed of the slit. A process that can explain the differences is presented here. The output signal appearing beyond the range of 400 MeV/n xenon ion beam was discussed. The sensitivity was compared with that obtained with hypervelocity collision of dust.

  15. Study of the characteristics of a piezoelectric lead zirconate titanate radiation detector using a pulsed xenon source

    NASA Astrophysics Data System (ADS)

    Miyachi, Takashi; Fujii, Masayuki; Hasebe, Nobuyuki; Okudaira, Osamu; Takechi, Seiji; Kurozumi, Atsuma; Morinaga, Shinya; Uno, Takefumi; Shibata, Hiromi; Kobayashi, Masanori; Murakami, Takeshi; Uchihori, Yukio; Okada, Nagaya

    2010-05-01

    The detector characteristics of piezoelectric lead zirconate titanate (PZT) were studied by directly irradiating a multilayered PZT detector with 400 MeV/n xenon ions. An extracted beam was processed with a rotating slit. Thus, passed through ˜103 xenon ions were available for 50 to 250 μs. The effect of polarization on the output signal was discussed, and the optimal electrode configuration was determined. The output signal appeared as an isolated pulse whose amplitude was qualitatively understood by the Bethe-Bloch formula. However, the calculated and the observed values differed depending on the rotation speed of the slit. A process that can explain the differences is presented here. The output signal appearing beyond the range of 400 MeV/n xenon ion beam was discussed. The sensitivity was compared with that obtained with hypervelocity collision of dust.

  16. Predicted effects of tritium exposure on fast-acting piezoelectric valves for gas fueling at TFTR

    SciTech Connect

    Gill, J.T.; Pierce, C.W.

    1985-09-01

    The prospects for using piezoelectrically-driven valves with elastomeric or thermoplastic poppets in tritium gas service have been investigated. A modeling study of a typical valve incorporating ethylene-propylene rubber (EPR) or high density polyethylene (HDPE) was performed. Equations were developed linking applied voltage; ceramic bimorph preloading force, elastic deflection modulus, and specific deflection force (per volt applied); polymer elastic modulus, thickness, seal surface area, and compression (to make seal); elastomer compression set; thermoplastic creep modulus; and flow gap between seat and polymer tip. It was determined that, while EPR should seal the valve orifice more easily, HDPE should produce a valve flow rate vs. voltage curve less variant with time and exposure. Both should, however, be sealable and allow flow curves perturbed by less than or equal to 10% of full scale after approx. 100 days of exposure to 10/sup 5/ Pa (1 atm) T/sub 2/ gas (equivalent to approx. 7 x 10/sup 7/ rad=7 x 10/sup 5/ Gy dosage).

  17. Predicted Effects of Tritium Exposures on Fast-Acting Piezoelectric Valves for Gas Fueling at TFTR

    SciTech Connect

    Gill, J. T.; Pierce, C. W.

    1985-04-01

    The prospects for using piezoelectrically-driven valves with elastomeric or thermoplastic poppets in tritium gas service have been investigated. A modelling study of a typical valve incorporating ethylene-propylene rubber (EPR) or high density polyethylene (HDPE) was performed. Equations were developed linking applied voltage; ceramic bimorph preloading force, elastic deflection modulus, and specific deflection force (per volt applied); polymer elastic modulus, thickness, seal surface area, and compression (to make seal); elastomer compression set; thermoplastic creep modulus; and flow gap between seat and polymer tip. It was determined that, while EPR should seal the valve orifice more easily, HDPE should produce a valve flow rate vs. voltage curve less variant with time and exposure. Both should, however, be sealable and allow flow curves perturbed by less than or equal to 10% of full scale after ~100 days of exposure to 10{sup}5 Pa (1 atm) T{sub}2 gas (equivalent to ~7 x 10{sup}7 rad = 7 x 10{sup}5 Gy dosage).

  18. Temporal Behavior of the Pump Pulses, Residual Pump Pulses, and THz Pulses for D2O Gas Pumped by a TEA CO2 Laser

    NASA Astrophysics Data System (ADS)

    Geng, Lijie; Zhang, Zhifeng; Zhai, Yusheng; Su, Yuling; Zhou, Fanghua; Qu, Yanchen; Zhao, Weijiang

    2016-08-01

    Temporal behavior of the pump pulses, residual pump pulses, and THz pulses for optically pumped D2O gas molecules was investigated by using a tunable TEA CO2 laser as the pumping source. The pulse profiles of pump laser pulses, residual pump pulses, and the THz output pulses were measured, simultaneously, at several different gas pressures. For THz pulse, the pulse delay between the THz pulse and the pump pulse was observed and the delay time was observed to increase from 40 to 70 ns with an increase in gas pressure from 500 to 1700 Pa. Both THz pulse broadening and compression were observed, and the pulse broadening effect transformed to the compression effect with increasing the gas pressure. For the residual pump pulse, the full width at half maximum (FWHM) of the main pulse decreased with increasing gas pressure, and the main pulse disappeared at high gas pressures. The secondary pulses were observed at high gas pressure, and the time intervals of about 518 and 435 ns were observed between the THz output pulse and the secondary residual pump pulse at the pressure of 1400 Pa and 1700 Pa, from which the vibrational relaxation time constants of about 5.45 and 5.55 μs Torr were obtained.

  19. High-repetition-rate short-pulse gas discharge.

    PubMed

    Tulip, J; Seguin, H; Mace, P N

    1979-09-01

    A high-average-power short-pulse gas discharge is described. This consists of a volume-preionized transverse discharge of the type used in gas lasers driven by a Blumlein energy storage circuit. The Blumlein circuit is fabricated from coaxial cable, is pulse-charged from a high-repetition-rate Marx-bank generator, and is switched by a high-repetition-rate segmented rail gap. The operation of this discharge under conditions typical of rare-gas halide lasers is described. A maximum of 900 pps was obtained, giving a power flow into the discharge of 30 kW. PMID:18699678

  20. Piezoelectric measurement of laser power

    DOEpatents

    Deason, Vance A.; Johnson, John A.; Telschow, Kenneth L.

    1991-01-01

    A method for measuring the energy of individual laser pulses or a series of laser pulses by reading the output of a piezoelectric (PZ) transducer which has received a known fraction of the total laser pulse beam. An apparatus is disclosed that reduces the incident energy on the PZ transducer by means of a beam splitter placed in the beam of the laser pulses.

  1. Effect of Pulse Parameters on Weld Quality in Pulsed Gas Metal Arc Welding: A Review

    NASA Astrophysics Data System (ADS)

    Pal, Kamal; Pal, Surjya K.

    2011-08-01

    The weld quality comprises bead geometry and its microstructure, which influence the mechanical properties of the weld. The coarse-grained weld microstructure, higher heat-affected zone, and lower penetration together with higher reinforcement reduce the weld service life in continuous mode gas metal arc welding (GMAW). Pulsed GMAW (P-GMAW) is an alternative method providing a better way for overcoming these afore mentioned problems. It uses a higher peak current to allow one molten droplet per pulse, and a lower background current to maintain the arc stability. Current pulsing refines the grains in weld fusion zone with increasing depth of penetration due to arc oscillations. Optimum weld joint characteristics can be achieved by controlling the pulse parameters. The process is versatile and easily automated. This brief review illustrates the effect of pulse parameters on weld quality.

  2. Experimental gas-fired pulse-combustion studies

    NASA Technical Reports Server (NTRS)

    Blomquist, C. A.

    1982-01-01

    Experimental studies conducted at Argonne National Laboratory on a gas-fired, water-cooled, Helmholtz-type pulse combustion burner are discussed. In addition to the experimental work, information is presented on the evolution of pulse combustion, the types of pulse combustion burners and their applications, and the types of fuels used. Also included is a survey of other pertinent studies of gas-fired pulse combustion. The burner used in the Argonne research effort was equipped with adjustable air and gas flapper valves and was operated stably over a heat-input range of 30,000 to 200,000 Btu/h. The burner's overall heat transfer in the pulsating mode was 22 to 31% higher than when the unit was operated in the steady mode. Important phenomena discussed include (1) effects on performance produced by inserting a corebustor to change tailpipe diameter, (2) effects observed following addition of an air-inlet decoupling chamber to the unit, and (3) occurrence of carbon monoxide in the exhaust gas.

  3. Continuous and Pulsed THz generation with molecular gas lasers and photoconductive antennas gated by femtosecond pulses

    NASA Astrophysics Data System (ADS)

    Cruz, Flavio C.; Nogueira, T.; Costa, Leverson F. L.; Jarschel, Paulo F.; Frateschi, Newton C.; Viscovini, Ronaldo C.; Vieira, Bruno R. B.; Guevara, Victor M. B.; Pereira, Daniel

    2008-04-01

    We report THz generation based on two systems: 1) continuous-wave (cw) laser generation in molecular gas lasers, and 2) short pulse generation in photoconductive antennas, gated by femtosecond near-infrared Ti:sapphire lasers. With the first system, we have generated tens of monochromatic cw laser lines over the last years, extending roughly from 40 microns to several hundred microns. This is done by optical pumping of gas lasers based on polar molecules such as methanol and its isotopes. In the second system, under development, pulsed THz radiation is generated by a photoconductive antenna built in a semi-insulating GaAs substrate excited by femtosecond pulses from a near-infrared (800 nm) Ti:sapphire laser.

  4. Instrumentation of dynamic gas pulse loading system

    SciTech Connect

    Mohaupt, H.

    1992-04-14

    The overall goal of this work is to further develop and field test a system of stimulating oil and gas wells, which increases the effective radius of the well bore so that more oil can flow into it, by recording pressure during the gas generation phase in real time so that fractures can be induced more predictably in the producing formation. Task 1: Complete the laboratory studies currently underway with the prototype model of the instrumentation currently being studied. Task 2: Perform field tests of the model in the Taft/Bakersfield area, utilizing operations closest to the engineers working on the project, and optimize the unit for various conditions encountered there. Task 3: Perform field test of the model in DGPL jobs which are scheduled in the mid-continent area, and optimize the unit for downhole conditions encountered there. Task 4: Analyze and summarize the results achieved during the complete test series, documenting the steps for usage of downhole instrumentation in the field, and compile data specifying use of the technology by others. Task 5: Prepare final report for DOE, and include also a report on the field tests completed. Describe and estimate the probability of the technology being commercialized and in what time span. The project has made substantial technical progress, though we are running about a month behind schedule. Expenditures are in line with the schedule. Increased widespread interest in the use of DGPL stimulation has kept us very busy. The computer modeling and test instrumentation developed under this program is already being applied to commercial operations.

  5. Piezoelectric Polymers

    NASA Technical Reports Server (NTRS)

    Harrison, J. S.; Ounaies, Z.; Bushnell, Dennis M. (Technical Monitor)

    2001-01-01

    The purpose of this review is to detail the current theoretical understanding of the origin of piezoelectric and ferroelectric phenomena in polymers; to present the state-of-the-art in piezoelectric polymers and emerging material systems that exhibit promising properties; and to discuss key characterization methods, fundamental modeling approaches, and applications of piezoelectric polymers. Piezoelectric polymers have been known to exist for more than forty years, but in recent years they have gained notoriety as a valuable class of smart materials.

  6. Decay of transverse acoustic waves in a pulsed gas laser

    SciTech Connect

    Kulkarny, V.A.

    1980-11-01

    The long-term characteristics of transverse acoustic waves in the cavity of a pulsed gaseous laser were studied by analyzing them in a straight duct configuration with nonlinear techniques used in sonic boom problems. A decaying sawtooth waveform containing a shockwave reverberated in the cavity transverse to the flow direction. In the asymptotic decay, the relative pressure perturbation of the wave varies as the 2/5 power of the product of the relative overpressure from the pulse and the speed of sound in the gas.

  7. Stress controlled pulsed direct current co-sputtered Al{sub 1−x}Sc{sub x}N as piezoelectric phase for micromechanical sensor applications

    SciTech Connect

    Fichtner, Simon; Reimer, Tim; Chemnitz, Steffen; Wagner, Bernhard; Lofink, Fabian

    2015-11-01

    Scandium alloyed aluminum nitride (Al{sub 1−x}Sc{sub x}N) thin films were fabricated by reactive pulsed direct current co-sputtering of separate scandium and aluminum targets with x ≤ 0.37. A significant improvement of the clamped transversal piezoelectric response to strain e{sub 31,f} from −1.28 C/m{sup 2} to −3.01 C/m{sup 2} was recorded, while dielectric constant and loss angle remain low. Further, the built-in stress level of Al{sub 1−x}Sc{sub x}N was found to be tuneable by varying pressure, Ar/N{sub 2} ratio, and Sc content. The thus resulting enhancement of the expectable signal to noise ratio by a factor of 2.1 and the ability to control built-in stress make the integration of Al{sub 1−x}Sc{sub x}N as the piezoelectric phase of micro-electro-mechanical system sensor applications highly attractive.

  8. Pulsed electron beam propagation in argon and nitrogen gas mixture

    SciTech Connect

    Kholodnaya, G. E.; Sazonov, R. V.; Ponomarev, D. V.; Remnev, G. E.; Zhirkov, I. S.

    2015-10-15

    The paper presents the results of current measurements for the electron beam, propagating inside a drift tube filled in with a gas mixture (Ar and N{sub 2}). The experiments were performed using the TEA-500 pulsed electron accelerator. The main characteristics of electron beam were as follows: 60 ns pulse duration, up to 200 J energy, and 5 cm diameter. The electron beam propagated inside the drift tube assembled of three sections. Gas pressures inside the drift tube were 760 ± 3, 300 ± 3, and 50 ± 1 Torr. The studies were performed in argon, nitrogen, and their mixtures of 33%, 50%, and 66% volume concentrations, respectively.

  9. Pulse tube stirling machine with warm gas-driven displacer

    NASA Astrophysics Data System (ADS)

    Zhu, Shaowei; Nogawa, Masafumi

    2010-05-01

    A pulse tube type stirling machine with warm gas-driven displacer which has a displacer rod is discussed with numerical simulation when it is used as a cryogenic refrigerator, room temperature refrigerator and engine. It has both the advantages of gas-driven-stirling machine with high efficiency and simplicity and the advantages of pulse tube machine with no moving parts at low temperatures. A nodal analysis method that includes the linear motor and the displacer in the machine is introduced. Numerical results show that it has high potential to be used as the cryogenic refrigerator, room temperature refrigerator and engine. In this type of machine, there is an optimum phase angle between displacer and piston, and an optimum swept volume ratio of displacer over compressor for efficiency. The phase angle and swept volume ratio can be adjusted by the natural frequency of the displacer and the diameter of the displacer rod when it is used as a refrigerator.

  10. A fast rise-rate, adjustable-mass-bit gas puff valve for energetic pulsed plasma experiments

    SciTech Connect

    Loebner, Keith T. K. Underwood, Thomas C.; Cappelli, Mark A.

    2015-06-15

    A fast rise-rate, variable mass-bit gas puff valve based on the diamagnetic repulsion principle was designed, built, and experimentally characterized. The ability to hold the pressure rise-rate nearly constant while varying the total overall mass bit was achieved via a movable mechanical restrictor that is accessible while the valve is assembled and pressurized. The rise-rates and mass-bits were measured via piezoelectric pressure transducers for plenum pressures between 10 and 40 psig and restrictor positions of 0.02-1.33 cm from the bottom of the linear restrictor travel. The mass-bits were found to vary linearly with the restrictor position at a given plenum pressure, while rise-rates varied linearly with plenum pressure but exhibited low variation over the range of possible restrictor positions. The ability to change the operating regime of a pulsed coaxial plasma deflagration accelerator by means of altering the valve parameters is demonstrated.

  11. A fast rise-rate, adjustable-mass-bit gas puff valve for energetic pulsed plasma experiments

    NASA Astrophysics Data System (ADS)

    Loebner, Keith T. K.; Underwood, Thomas C.; Cappelli, Mark A.

    2015-06-01

    A fast rise-rate, variable mass-bit gas puff valve based on the diamagnetic repulsion principle was designed, built, and experimentally characterized. The ability to hold the pressure rise-rate nearly constant while varying the total overall mass bit was achieved via a movable mechanical restrictor that is accessible while the valve is assembled and pressurized. The rise-rates and mass-bits were measured via piezoelectric pressure transducers for plenum pressures between 10 and 40 psig and restrictor positions of 0.02-1.33 cm from the bottom of the linear restrictor travel. The mass-bits were found to vary linearly with the restrictor position at a given plenum pressure, while rise-rates varied linearly with plenum pressure but exhibited low variation over the range of possible restrictor positions. The ability to change the operating regime of a pulsed coaxial plasma deflagration accelerator by means of altering the valve parameters is demonstrated.

  12. Autonomous portable pulsed-periodical generator of high-power radiofrequency-pulses based on gas discharge with hollow cathode

    NASA Astrophysics Data System (ADS)

    Bulychev, Sergey V.; Dubinov, Alexander E.; L'vov, Igor L.; Popolev, Vyacheslav L.; Sadovoy, Sergey A.; Sadchikov, Eugeny A.; Selemir, Victor D.; Valiulina, Valeria K.; Vyalykh, Dmitry V.; Zhdanov, Victor S.

    2016-05-01

    Portable autonomous generator of high-power RF-pulses based on the gas discharge with hollow cathode has been designed, fabricated, and tested. Input and output characteristics are the following: discharge current amplitude is 800 A, duration of generated RF-pulses is 350 ns, carrier frequency is ˜90 MHz, power in RF-pulse is 0.5 MW, pulse repetition rate is 0.5 kHz, and device efficiency is ˜25%.

  13. Autonomous portable pulsed-periodical generator of high-power radiofrequency-pulses based on gas discharge with hollow cathode.

    PubMed

    Bulychev, Sergey V; Dubinov, Alexander E; L'vov, Igor L; Popolev, Vyacheslav L; Sadovoy, Sergey A; Sadchikov, Eugeny A; Selemir, Victor D; Valiulina, Valeria K; Vyalykh, Dmitry V; Zhdanov, Victor S

    2016-05-01

    Portable autonomous generator of high-power RF-pulses based on the gas discharge with hollow cathode has been designed, fabricated, and tested. Input and output characteristics are the following: discharge current amplitude is 800 A, duration of generated RF-pulses is 350 ns, carrier frequency is ∼90 MHz, power in RF-pulse is 0.5 MW, pulse repetition rate is 0.5 kHz, and device efficiency is ∼25%. PMID:27250451

  14. Advances in pulsed-laser-deposited AIN thin films for high-temperature capping, device passivation, and piezoelectric-based RF MEMS/NEMS resonator applications

    NASA Astrophysics Data System (ADS)

    Hullavarad, S. S.; Vispute, R. D.; Nagaraj, B.; Kulkarni, V. N.; Dhar, S.; Venkatesan, T.; Jones, K. A.; Derenge, M.; Zheleva, T.; Ervin, M. H.; Lelis, A.; Scozzie, C. J.; Habersat, D.; Wickenden, A. E.; Currano, L. J.; Dubey, M.

    2006-04-01

    In this paper we report recent advances in pulsed-laser-deposited AIN thin films for high-temperature capping of SiC, passivation of SiC-based devices, and fabrication of a piezoelectric MEMS/NEMS resonator on Pt-metallized SiO2/Si. The AlN films grown using the reactive laser ablation technique were found to be highly stoichiometric, dense with an optical band gap of 6.2 eV, and with a surface smoothness of less than 1 nm. A low-temperature buffer-layer approach was used to reduce the lattice and thermal mismatch strains. The dependence of the quality of AlN thin films and its characteristics as a function of processing parameters are discussed. Due to high crystallinity, near-perfect stoichiometry, and high packing density, pulsed-laser-deposited AlN thin films show a tendency to withstand high temperatures up to 1600°C, and which enables it to be used as an anneal capping layer for SiC wafers for removing ion-implantation damage and dopant activation. The laser-deposited AlN thin films show conformal coverage on SiC-based devices and exhibit an electrical break-down strength of 1.66 MV/cm up to 350°C when used as an insulator in Ni/AlN/SiC metal-insulator-semiconductor (MIS) devices. Pulsed laser deposition (PLD) AlN films grown on Pt/SiO2/Si (100) substrates for radio-frequency microelectrical and mechanical systems and nanoelectrical and mechanical systems (MEMS and NEMS) demonstrated resonators having high Q values ranging from 8,000 to 17,000 in the frequency range of 2.5-0.45 MHz. AlN thin films were characterized by x-ray diffraction, Rutherford backscattering spectrometry (in normal and oxygen resonance mode), atomic force microscopy, ultraviolet (UV)-visible spectroscopy, and scanning electron microscopy. Applications exploiting characteristics of high bandgap, high bond strength, excellent piezoelectric characteristics, extremely high chemical inertness, high electrical resistivity, high breakdown strength, and high thermal stability of the pulsed

  15. Pulsed laser linescanner for a backscatter absorption gas imaging system

    DOEpatents

    Kulp, Thomas J.; Reichardt, Thomas A.; Schmitt, Randal L.; Bambha, Ray P.

    2004-02-10

    An active (laser-illuminated) imaging system is described that is suitable for use in backscatter absorption gas imaging (BAGI). A BAGI imager operates by imaging a scene as it is illuminated with radiation that is absorbed by the gas to be detected. Gases become "visible" in the image when they attenuate the illumination creating a shadow in the image. This disclosure describes a BAGI imager that operates in a linescanned manner using a high repetition rate pulsed laser as its illumination source. The format of this system allows differential imaging, in which the scene is illuminated with light at least 2 wavelengths--one or more absorbed by the gas and one or more not absorbed. The system is designed to accomplish imaging in a manner that is insensitive to motion of the camera, so that it can be held in the hand of an operator or operated from a moving vehicle.

  16. Development of Long-Lifetime Pulsed Gas Valves for Pulsed Electric Thrusters

    NASA Technical Reports Server (NTRS)

    Burkhardt, Wendel M.; Crapuchettes, John M.; Addona, Brad M.; Polzin, Kurt A.

    2015-01-01

    The design and test results for two types of pulsed gas valves are presented. The valves, a piezo valve and a solenoid actuated valve, must have exceedingly long lifetime to support gas-fed pulsed electric thruster operation for missions of interest. The performance of both valves was tested, with both demonstrating the capability to throttle the gas flow rate while maintaining low leakage levels below 10(exp -3) sccs of He at the beginning of valve lifetime. The piezo valve varies the flow rate by changing the amount that the valve is open, which is a function of applied voltage. This valve demonstrated continuous throttlability from 0-10 mL/s, with opening and closing times of 100 microsecond or less. The solenoid actuated valve flow rate changes as a function of the inlet gas pressure, with demonstrated flow rates in these tests from 2.7-11 mL per second. The valve response time is slower than the piezo valve, opening in 1-2 ms and closing in several ms. The solenoid actuated valve was tested to one million cycles, with the valve performance remaining relatively unchanged throughout the test. Galling of the sliding plunger caused the valve to bind and fail just after one million cycles, but at this point in the test the valve sealing surface leak rate still appeared to be well below the maximum target leak rake of 1×10(exp -3) sccs of He.

  17. Silicon oxynitride thin films synthesised by the reactive gas pulsing process using rectangular pulses

    NASA Astrophysics Data System (ADS)

    Aubry, E.; Weber, S.; Billard, A.; Martin, N.

    2011-09-01

    Silicon oxynitride thin films were synthesised by the reactive gas pulsing process using an argon, oxygen and nitrogen gas mixture from a semiconductor Si target. Argon and nitrogen were introduced at a constant mass flow rate, whereas oxygen gas was periodically supplied using a rectangular pulsed flow rate. The O2 injection time TON (or duty cycle α) was the only varied parameter. The influences of this parameter on the discharge behaviour, on the Si target voltage, and on the resulting chemical composition of the films were investigated. The temporal evolution of the total pressure exhibits exponential shape differing from the rectangular oxygen pulse shape, due to the response time of the gas flowmeter and to the progressive oxidation of the target and the chamber walls. During the TON time, the preferential adsorption of the introduced O2 induces a decay in Si target voltage. Reversion to the nitrided mode is still possible as soon as the O2 injection is stopped. The elemental analyses assessed by secondary neutral mass spectrometry (SNMS) showed that the O/N ratio within silicon oxynitride films linearly depends on the TON time. Increasing the duty cycle α over a certain value results in an oxidised steady state formation during the TON time. This formation was observed by real time measurements of the emission lines ratio I(O*)/I(Ar*) indicative of the O2 partial pressure and confirmed by the time derivative of the target voltage. During the TOFF time, the alternation with the nitrided mode becomes impossible, leading to the specific synthesis of stoichiometric SiO2 films.

  18. Ultra-Intense Laser Pulse Propagation in Gas and Plasma

    SciTech Connect

    Antonsen, T. M.

    2004-10-26

    It is proposed here to continue their program in the development of theories and models capable of describing the varied phenomena expected to influence the propagation of ultra-intense, ultra-short laser pulses with particular emphasis on guided propagation. This program builds upon expertise already developed over the years through collaborations with the NSF funded experimental effort lead by Professor Howard Milchberg here at Maryland, and in addition the research group at the Ecole Polytechnique in France. As in the past, close coupling between theory and experiment will continue. The main effort of the proposed research will center on the development of computational models and analytic theories of intense laser pulse propagation and guiding structures. In particular, they will use their simulation code WAKE to study propagation in plasma channels, in dielectric capillaries and in gases where self focusing is important. At present this code simulates the two-dimensional propagation (radial coordinate, axial coordinate and time) of short pulses in gas/plasma media. The plasma is treated either as an ensemble of particles which respond to the ponderomotive force of the laser and the self consistent electric and magnetic fields created in the wake of pulse or as a fluid. the plasma particle motion is treated kinetically and relativistically allowing for study of intense pulses that result in complete cavitation of the plasma. The gas is treated as a nonlinear medium with rate equations describing the various stages of ionization. A number of important physics issues will be addressed during the program. These include (1) studies of propagation in plasma channels, (2) investigation of plasma channel nonuniformities caused by parametric excitation of channel modes, (3) propagation in dielectric capillaries including harmonic generation and ionization scattering, (4) self guided propagation in gas, (5) studies of the ionization scattering instability recently

  19. Selective, pulsed CVD of platinum on microfilament gas sensors

    SciTech Connect

    Manginell, R.P.; Smith, J.H.; Ricco, A.J.; Moreno, D.J.; Hughes, R.C.; Huber, R.J.; Senturia, S.D.

    1996-05-01

    A post-processing, selective micro-chemical vapor deposition (``micro-CVD``) technology for the deposition of catalytic films on surface-micromachined, nitride-passivated polysilicon filaments has been investigated. Atmospheric pressure deposition of Pt on microfilaments was accomplished by thermal decomposition of Pt acetylacetonate; deposition occurs selectively only on those filaments which are electrically heated. Catalyst morphology, characterized by SEM, can be controlled by altering deposition time, filament temperature, and through the use of pulsed heating of the filament during deposition. Morphology plays an important role in determining the sensitivity of these devices when used as combustible gas sensors.

  20. Pulsed NMR investigation of the supercooled water-gas hydrate-gas metastable equilibrium

    NASA Astrophysics Data System (ADS)

    Vlasov, V. A.; Zavodovsky, A. G.; Madygulov, M. Sh.; Nesterov, A. N.; Reshetnikov, A. M.

    2013-11-01

    A method is developed for determining the thermobaric conditions of phase equilibrium in a liquid water-hydrate-gas system by means of pulsed 1H NMR. The method is founded on NMR-based measurements of the amount of liquid water phase in a sample containing gas hydrate under certain values of pressure p and temperature T. The results from investigating the p, T conditions for metastable equilibrium in a supercooled water-Freon-12 hydrate-gas system are presented. The results are in good agreement with the known literature data.

  1. Pulsed electrical discharge in gas bubbles in water

    NASA Astrophysics Data System (ADS)

    Gershman, Sophia

    A phenomenological picture of pulsed electrical discharge in gas bubbles in water is produced by combining electrical, spectroscopic, and imaging methods. The discharge is generated by applying one microsecond long 5 to 20 kilovolt pulses between the needle and disk electrodes submerged in water. A gas bubble is generated at the tip of the needle electrode. The study includes detailed experimental investigation of the discharge in argon bubbles and a brief look at the discharge in oxygen bubbles. Imaging, electrical characteristics, and time-resolved optical emission data point to a fast streamer propagation mechanism and formation of a plasma channel in the bubble. Spectroscopic methods based on line intensity ratios and Boltzmann plots of line intensities of argon, atomic hydrogen, and argon ions and the examination of molecular emission bands from molecular nitrogen and hydroxyl radicals provide evidence of both fast beam-like electrons and slow thermalized ones with temperatures of 0.6 -- 0.8 electron-volts. The collisional nature of plasma at atmospheric pressure affects the decay rates of optical emission. Spectroscopic study of rotational-vibrational bands of hydroxyl radical and molecular nitrogen gives vibrational and rotational excitation temperatures of the discharge of about 0.9 and 0.1 electron-volt, respectively. Imaging and electrical evidence show that discharge charge is deposited on the bubble wall and water serves as a dielectric barrier for the field strength and time scales of this experiment. Comparing the electrical and imaging information for consecutive pulses applied at a frequency of 1 Hz indicates that each discharge proceeds as an entirely new process with no memory of the previous discharge aside from long-lived chemical species, such as ozone and oxygen. Intermediate values for the discharge gap and pulse duration, low repetition rate, and unidirectional character of the applied voltage pulses make the discharge process here unique

  2. Instrumentation of Dynamic Gas Pulse Loading system. Final technical report

    SciTech Connect

    Mohaupt, H.

    1993-07-31

    The Dynamic Gas Pulse Loading (DGPL) process is an hydraulic fracturing method which uses CO{sub 2} and CO gas as a working fluid instead of a liquid. The DGPL system can be used to generate fractures for horizontal and vertical oil and gas well completions in both open hole and perforated casing. The DGPL system provides a cost effective tool for repairing near well bore permeability damage caused by inappropriate chemical treatment, migrating fines and paraffins, or slotted liners blocked by sand. Because the gas is generated from a solid propellant material by chemical reaction, no heavy equipment is required. Tremendous pump rates can be obtained. Peak pressures are naturally localized at the tool position by the tamping effect of well fluids. Thus many of the leakage and sealing problems which plague static hydrofrac processes ore completely avoided. DGPL may be effectively used before acid treatment to provide fresh pathways for the acid to reach the formation. The smaller tools may be positioned by wireline, though most Stressfrac tools are tubing conveyed.

  3. High-Temperature Piezoelectric Sensing

    PubMed Central

    Jiang, Xiaoning; Kim, Kyungrim; Zhang, Shujun; Johnson, Joseph; Salazar, Giovanni

    2014-01-01

    Piezoelectric sensing is of increasing interest for high-temperature applications in aerospace, automotive, power plants and material processing due to its low cost, compact sensor size and simple signal conditioning, in comparison with other high-temperature sensing techniques. This paper presented an overview of high-temperature piezoelectric sensing techniques. Firstly, different types of high-temperature piezoelectric single crystals, electrode materials, and their pros and cons are discussed. Secondly, recent work on high-temperature piezoelectric sensors including accelerometer, surface acoustic wave sensor, ultrasound transducer, acoustic emission sensor, gas sensor, and pressure sensor for temperatures up to 1,250 °C were reviewed. Finally, discussions of existing challenges and future work for high-temperature piezoelectric sensing are presented. PMID:24361928

  4. Piezoelectric Film.

    ERIC Educational Resources Information Center

    Garrison, Steve

    1992-01-01

    Presents activities that utilize piezoelectric film to familiarize students with fundamental principles of electricity. Describes classroom projects involving chemical sensors, microbalances, microphones, switches, infrared sensors, and power generation. (MDH)

  5. Pulse-jet baghouse performance improvement with flue gas conditioning

    SciTech Connect

    Miller, S.J.; Laudal, D.L.

    1992-10-01

    A pilot study was conducted at the Energy and Environmental Research Center (EERC) at the University of North Dakota to evaluate the effectiveness of flue gas conditioning in reducing tube sheet pressure drop and fine particulate emissions from a pulse-jet fabric filter. The project was jointly funded by the US Department of Energy (DOE), the Electric Power Research Institute (EPRI), and the Canadian Electrical Association (CEA). The work was completed with EERC facilities consisting of a pulverized coal-fired combustor and pilot baghouse. Full-scale pulse-jet bags were employed under conditions similar to large-scale baghouses. The investigation included baseline tests and tests in which ammonia and SO[sub 3] were, injected upstream of the baghouse to determine the effect of conditioning on baghouse performance. The primary independent variables included coal type, conditioning agent concentrations, air-to-cloth (A/C) ratio, and fabric type. The main dependent variables were particulate emissions, bagbouse pressure drop, and cohesive properties of the fly ash. Results demonstrated significant benefits of using conditioning with a pulse-jet baghouse, including a substantial reduction in particulate emissions and a substantial reduction in pressure drop (or the ability to operate at a higher A/C ratio without increasing pressure drop or bag-cleaning frequency). The improvements in fabric filter performance correlate strongly with a shift in the tensile strength and with increases in the aerated and packed porosity of the fly ash. Conditioning appears to be applicable to a wide range of coals and fabrics. Applications for this technology are where there is a need to reduce pressure drop and/or particulate emissions in existing bagbouses, to reduce fine-particle air toxic emissions which may be required in the future, and for new bagbouse installations to allow operation at a higher A/C ratio while providing an ultrahigh fine-particle collection efficiency.

  6. Pulse-jet baghouse performance improvement with flue gas conditioning

    SciTech Connect

    Miller, S.J.; Laudal, D.L.

    1992-10-01

    A pilot study was conducted at the Energy and Environmental Research Center (EERC) at the University of North Dakota to evaluate the effectiveness of flue gas conditioning in reducing tube sheet pressure drop and fine particulate emissions from a pulse-jet fabric filter. The project was jointly funded by the US Department of Energy (DOE), the Electric Power Research Institute (EPRI), and the Canadian Electrical Association (CEA). The work was completed with EERC facilities consisting of a pulverized coal-fired combustor and pilot baghouse. Full-scale pulse-jet bags were employed under conditions similar to large-scale baghouses. The investigation included baseline tests and tests in which ammonia and SO{sub 3} were, injected upstream of the baghouse to determine the effect of conditioning on baghouse performance. The primary independent variables included coal type, conditioning agent concentrations, air-to-cloth (A/C) ratio, and fabric type. The main dependent variables were particulate emissions, bagbouse pressure drop, and cohesive properties of the fly ash. Results demonstrated significant benefits of using conditioning with a pulse-jet baghouse, including a substantial reduction in particulate emissions and a substantial reduction in pressure drop (or the ability to operate at a higher A/C ratio without increasing pressure drop or bag-cleaning frequency). The improvements in fabric filter performance correlate strongly with a shift in the tensile strength and with increases in the aerated and packed porosity of the fly ash. Conditioning appears to be applicable to a wide range of coals and fabrics. Applications for this technology are where there is a need to reduce pressure drop and/or particulate emissions in existing bagbouses, to reduce fine-particle air toxic emissions which may be required in the future, and for new bagbouse installations to allow operation at a higher A/C ratio while providing an ultrahigh fine-particle collection efficiency.

  7. Mn-doped 0.15BiInO3-0.85PbTiO3 piezoelectric films deposited by pulsed laser deposition

    NASA Astrophysics Data System (ADS)

    Lee, Sun Young; Ko, Song Won; Lee, Soonil; Trolier-McKinstry, Susan

    2012-05-01

    Undoped, 0.5 and 1.0 mol. % Mn-doped 0.15BiInO3-0.85PbTiO3 films were grown on PbTiO3/Pt/Ti/SiO2/Si substrates by pulsed laser deposition. Phase-pure perovskite films were obtained at a substrate temperature of 585 °C irrespective of Mn doping level. The 0.5 mol. % Mn-doped films showed a room temperature permittivity of 480 and a dielectric loss tangent of 0.015 at 100 kHz after 650 °C post-deposition annealing. The coercive field and remanent polarization were 80 kV/cm and 29 µC/cm2, respectively. The ferroelectric transition temperature of the films ranged from 535 to 585 °C. The e31,f piezoelectric coefficient was -7.1 C/m2. X-ray diffraction and phase transition temperature data showed that the Mn atoms substitute on the Ti-site as Mn3+; the resulting films have p-type conduction characteristics.

  8. Dual-frequency focused ultrasound using optoacoustic and piezoelectric transmitters for single-pulsed free-field cavitation in water

    NASA Astrophysics Data System (ADS)

    Baac, Hyoung Won; Lee, Taehwa; Ok, Jong G.; Hall, Timothy; Jay Guo, L.

    2013-12-01

    Pulsed ultrasonic cavitation is a promising modality for non-contact targeted therapy, enabling mechanical ablation of the tissue. We demonstrate a spatio-temporal superposition approach of two ultrasound pulses (high and low frequencies) producing a tight cavitation zone of 100 μm in water, which is an-order-of-magnitudes smaller than those obtained by the existing high-amplitude transducers. Particularly, laser-generated focused ultrasound (LGFU) was employed for the high-frequency operation (15 MHz). As demonstrated, LGFU plays a primary role to define the cavitation zone. The generation rate of cavitation bubbles could be dramatically increased up to 4.1% (cf. 0.06% without the superposition) with moderated threshold requirement.

  9. Selection of peptide ligands for piezoelectric peptide based gas sensors arrays using a virtual screening approach.

    PubMed

    Pizzoni, Daniel; Mascini, Marcello; Lanzone, Valentina; Del Carlo, Michele; Di Natale, Corrado; Compagnone, Dario

    2014-02-15

    Virtual and experimental affinity binding properties of 5 different peptides (cysteinylglycine, glutathione, Cys-Ile-His-Asn-Pro, Cys-Ile-Gln-Pro-Val, Cys-Arg-Gln-Val-Phe) vs. 14 volatile compounds belonging to relevant chemical classes were evaluated. The peptides were selected in order to have a large variability in physicochemical characteristics (including length). In virtual screening a rapid and cost-effective computational methodology for predicting binding scores of small peptide receptors vs. volatile compounds is proposed. Flexibility was considered for both ligands and peptides and each peptide conformer was treated as a possible receptor, generating a dedicated box and then running a docking process vs. all possible conformers of the 14 volatile compounds. The 5 peptides were covalently bound to gold nanoparticles and deposited onto 20 MHz quartz crystal microbalances to realize gas sensors. Gas sensing confirmed that each of the peptide conferred to the gold nanoparticles a particular selectivity pattern able to discriminate the 14 volatile compounds. The largest response was obtained for the pentapeptides Cys-Ile-His-Asn-Pro and Cys-Ile-Gln-Pro-Val while low response was achieved for the dipeptide. The comparative study, carried using a two-tailed T test, demonstrated that virtual screening was able to predict reliably the sensing ability of the pentapeptides. The dipeptide receptor exhibited 29% of virtual-experimental matching vs. 71% of glutathione and up to 93% for the pentapeptides. This virtual screening approach was proved to be a promising tool in predicting the behaviour of sensors array for gas detection. PMID:24060973

  10. BIOVENTING - Groundwater Aeration by Discontinuous Oxygen Gas Pulse Injections

    NASA Astrophysics Data System (ADS)

    Schirmer, M.

    2003-12-01

    Groundwater aeration by discontinuous oxygen gas pulse injections appears to be a promising concept for enhanced natural attenuation of dissolved contaminants that are susceptible for oxygenase enzyme attacks. Oxygen amendments facilitate indigenous microbiota to catabolize groundwater pollutants, such as aromatics, that are considered to be recalcitrant in absence of dissolved oxygen. As a rule, natural attenuation of many pollutants under aerobic conditions is considerably faster than under anaerobic conditions. Thus, enhancing the dissolved oxygen level appears to be worthwhile. In situ aeration of groundwater has been accomplished by air sparging, H2O2-supply, or by utilization of oxygen release compounds. However, continuous aeration of previously anaerobic groundwater is not desirable for several reasons: (a) economic efforts too high, (b) pollutant dislocation towards surface (desired only in air sparging), (c) risk of aquifer clogging (gas clogging, oxidation of ferrous iron, formation of bioslimes). In contrast, discontinuous oxygen gas sparging provides only for periodical groundwater aeration which is followed by microaerobic and suboxic conditions. Microaerobic conditions can prevail spatially (e.g., at plume fringes or within biofilms) or temporarily (e.g., at discontinuous bioventing). They still allow adapted bacteria to transform environmental pollutants to less toxic compounds, e.g., aromatic ring cleavage after dioxygenasis attack. Ring cleavage products, on the other hand, may be degraded more easily by anaerobic consortia than the initial aromatic compounds, making oxygen depletion periods highly intriguing in regard to an initiation of natural attenuation processes at plume fringes. In our work we outline the effect of oxygen depletion conditions on biodegradation of monchlorobenzene (MCB) as they occur subsequently to temporary aeration periods. For microaerobic conditions, relative to the oxygen supply, a stoichiometric transformation of MCB

  11. Compact permanent magnet H+ ECR ion source with pulse gas valve

    NASA Astrophysics Data System (ADS)

    Iwashita, Y.; Tongu, H.; Fuwa, Y.; Ichikawa, M.

    2016-02-01

    Compact H+ ECR ion source using permanent magnets is under development. Switching the hydrogen gas flow in pulse operations can reduce the gas loads to vacuum evacuation systems. A specially designed piezo gas valve chops the gas flow quickly. A 6 GHz ECR ion source equipped with the piezo gas valve is tested. The gas flow was measured by a fast ion gauge and a few ms response time is obtained.

  12. In situ health monitoring of piezoelectric sensors

    NASA Technical Reports Server (NTRS)

    Jensen, Scott L. (Inventor); Drouant, George J. (Inventor)

    2013-01-01

    An in situ health monitoring apparatus may include an exciter circuit that applies a pulse to a piezoelectric transducer and a data processing system that determines the piezoelectric transducer's dynamic response to the first pulse. The dynamic response can be used to evaluate the operating range, health, and as-mounted resonance frequency of the transducer, as well as the strength of a coupling between the transducer and a structure and the health of the structure.

  13. Piezoelectric Nanoindentation

    SciTech Connect

    Rar, Andrei; Pharr, George Mathews; Oliver, Warren C.; Karapetian, Edgar; Kalinin, Sergei V

    2006-01-01

    Piezoelectric nanoindentation (PNI) has been developed to quantitatively address electromechanical coupling and pressure-induced dynamic phenomena in ferroelectric materials on the nanoscale. In PNI, an oscillating voltage is applied between the back side of the sample and the indenter tip, and the first harmonic of bias-induced surface displacement at the area of indenter contact is detected. PNI is implemented using a standard nanoindentation system equipped with a continuous stiffness measurement system. The piezoresponse of polycrystalline lead zirconate titanate (PZT) and BaTiO{sub 3} piezoceramics was studied during a standard nanoindentation experiment. For PZT, the response was found to be load independent, in agreement with theoretical predictions. In polycrystalline barium titanate, a load dependence of the piezoresponse was observed. The potential of piezoelectric nanoindentation for studies of phase transitions and local structure-property relations in piezoelectric materials is discussed.

  14. Development of a Gas-Fed Pulse Detonation Research Engine

    NASA Technical Reports Server (NTRS)

    Litchford, Ron J.; Hutt, John (Technical Monitor)

    2001-01-01

    In response to the growing need for empirical data on pulse detonation engine performance and operation, NASA Marshall Space Flight Center has developed and placed into operation a low-cost gas-fed pulse detonation research engine. The guiding design strategy was to achieve a simple and flexible research apparatus, which was inexpensive to build and operate. As such, the engine was designed to operate as a heat sink device, and testing was limited to burst-mode operation with run durations of a few seconds. Wherever possible, maximum use was made of standard off-the-shelf industrial or automotive components. The 5-cm diameter primary tube is about 90-cm long and has been outfitted with a multitude of sensor and optical ports. The primary tube is fed by a coaxial injector through an initiator tube, which is inserted directly into the injector head face. Four auxiliary coaxial injectors are also integrated into the injector head assembly. All propellant flow is controlled with industrial solenoid valves. An automotive electronic ignition system was adapted for use, and spark plugs are mounted in both tubes so that a variety of ignition schemes can be examined. A microprocessor-based fiber-optic engine control system was developed to provide precise control over valve and ignition timing. Initial shakedown testing with hydrogen/oxygen mixtures verified the need for Schelkin spirals in both the initiator and primary tubes to ensure rapid development of the detonation wave. Measured pressure wave time-of-flight indicated detonation velocities of 2.4 km/sec and 2.2 km/sec in the initiator and primary tubes, respectively. These values implied a fuel-lean mixture corresponding to an H2 volume fraction near 0.5. The axial distribution for the detonation velocity was found to be essentially constant along the primary tube. Time-resolved thrust profiles were also acquired for both underfilled and overfilled tube conditions. These profiles are consistent with previous time

  15. Effects of ionic liquid electrode on pulse discharge plasmas in the wide range of gas pressures

    SciTech Connect

    Chen Qiang; Hatakeyama, Rikizo; Kaneko, Toshiro

    2010-11-15

    Gas-liquid interfacial pulse discharge plasmas are generated in the wide range of gas pressures, where an ionic liquid is used as the liquid electrode. By analyzing the characteristics of discharge voltage and current, the discharge mechanisms at low and high pressures are found to be dominated by secondary electron emission and first Townsend ionization, respectively. Therefore, the discharge properties at low and high pressures are mainly determined by the cathode material and the discharge gas type, respectively. Furthermore, the plasma properties are investigated by a double Langmuir probe. The density of the positive pulse plasma is found to be much smaller than that of the negative pulse plasma, although the discharge voltage and current of the negative and positive pulse plasmas are of the same order of magnitude. The positive pulse discharge plasma is considered to quickly diffuse onto the chamber wall from the radially central region due to its high plasma potential compared with that in the peripheral region.

  16. Impact of Dissociation and Sensible Heat Release on Pulse Detonation and Gas Turbine Engine Performance

    NASA Technical Reports Server (NTRS)

    Povinelli, Louis A.

    2001-01-01

    A thermodynamic cycle analysis of the effect of sensible heat release on the relative performance of pulse detonation and gas turbine engines is presented. Dissociation losses in the PDE (Pulse Detonation Engine) are found to cause a substantial decrease in engine performance parameters.

  17. Prepulse effect on intense femtosecond laser pulse propagation in gas

    SciTech Connect

    Giulietti, Antonio; Tomassini, Paolo; Galimberti, Marco; Giulietti, Danilo; Gizzi, Leonida A.; Koester, Petra; Labate, Luca; Ceccotti, Tiberio; D'Oliveira, Pascal; Auguste, Thierry; Monot, Pascal; Martin, Philippe

    2006-09-15

    The propagation of an ultrashort laser pulse can be affected by the light reaching the medium before the pulse. This can cause a serious drawback to possible applications. The propagation in He of an intense 60-fs pulse delivered by a Ti:sapphire laser in the chirped pulse amplification (CPA) mode has been investigated in conditions of interest for laser-plasma acceleration of electrons. The effects of both nanosecond amplified spontaneous emission and picosecond pedestals have been clearly identified. There is evidence that such effects are basically of refractive nature and that they are not detrimental for the propagation of a CPA pulse focused to moderately relativistic intensity. The observations are fully consistent with numerical simulations and can contribute to the search of a stable regime for laser acceleration.

  18. Intense microwave pulse propagation through gas breakdown plasmas in a waveguide

    SciTech Connect

    Byrne, D.P.

    1986-10-08

    High-power microwave pulse-compression techniques are used to generate 2.856 GHz pulses which are propagated in a TE/sub 10/ mode through a gas filled section of waveguide, where the pulses interact with self-generated gas-breakdown plasmas. Pulse envelopes transmitted through the plasmas, with duration varying from 2 ns to greater than 1 ..mu..s, and peak powers of a few kW to nearly 100 MW, are measured as a function of incident pulse and gas pressure for air, nitrogen, and helium. In addition, the spatial and temporal development of the optical radiation emitted by the breakdown plasmas are measured. For transmitted pulse durations greater than or equal to 100 ns, good agreement is found with both theory and existing measurements. For transmitted pulse duration as short as 2 ns (less than 10 rf cycles), a two-dimensional model is used in which the electrons in the plasma are treated as a fluid whose interactions with the microwave pulse are governed by a self-consistent set of fluid equations and Maxwell's equations for the electromagnetic field. The predictions of this model for air are compared with the experimental results over a pressure range of 0.8 torr to 300 torr. Good agreement is obtained above about 1 torr pressure, demonstrating that microwave pulse propagation above the breakdown threshold can be accurately modeled on this time scale. 63 refs., 44 figs., 2 tabs.

  19. Growth of arc in high-pressure, pulsed glow discharge by gas density depletion

    NASA Astrophysics Data System (ADS)

    Imada, Go; Yatsui, Kiyoshi; Masuda, Wataru

    2000-10-01

    Effects of gas density depletion on arc formation of high-pressure, pulsed glow discharge have been investigated by eliminating the other factors which may affect the discharge stability, such as shock waves, residual ions, electrode heating, and discharge products. The gas density depletion has been simulated by utilizing a subsonic gas flow between the curved electrodes combined with a convergent nozzle and a divergent diffuser. A comparison has been made on the discharge in the aerodynamically created gas density depletion with the second discharge in the double-pulse discharge within a stable gas. We have found that the large gas density depletion, Δρ/ρ0˜-3.6% corresponding to a pulse repetition rate (PRR) of ˜50 Hz, tends to cause an arc-like filament or an arc without the shocks, ions, electrode heating, and products. However, the second discharge in the double-pulse discharge becomes an arc in much smaller gas density depletion (Δρ/ρ0˜-1.2% corresponding to PRR ˜3 Hz). Therefore, the collapse of high-pressure, pulsed glow discharge is most likely caused by some factor other than the gas density depletion.

  20. Device for the removal of sulfur dioxide from exhaust gas by pulsed energization of free electrons

    SciTech Connect

    Mizuno, A.; Clements, J.S.; Davis, R.H.

    1984-01-01

    The performance of a new device using pulsed streamer corona for the removal of sulfur dioxide from humid air has been evaluated. The pulsed streamer corona produced free electrons which enhance gas-phase chemical reactions, and convert SO/sub 2/ to sulfuric acid mist. The SO/sub 2/ removal efficiency was compared with that of the electron-beam flue-gas treatment process. The comparison demonstrates the advantage of the novel device.

  1. Study of mass and cluster flux in a pulsed gas system with enhanced nanoparticle aggregation

    NASA Astrophysics Data System (ADS)

    Drache, Steffen; Stranak, Vitezslav; Hubicka, Zdenek; Berg, Florian; Tichy, Milan; Helm, Christiane A.; Hippler, Rainer

    2014-10-01

    The paper is focused on investigation of enhanced metal (Cu) cluster growth in a source of Haberland's type using pulsed gas aggregation. The aggregation Ar gas was delivered into the cluster source in a pulse regime, which results in the formation of well pronounced aggregation pressure peaks. The pressure peaks were varied by varying the different pulse gas frequency at the same mean pressure kept for all experiments. Hence, we were able to study the effect of enhanced aggregation pressure on cluster formation. Time-resolved measurements of cluster mass distribution were performed to estimate the mass and particle flux. The paper demonstrates that pulse gas aggregation influences growth of Cu nanoparticles, i.e., cluster mass/size, mass flux, and particle flux emitted from the cluster source. It was found that cluster mass related quantities are strongly influenced by pulsed gas frequency; the highest value of mass flux appears at the most pronounced pressure peaks. On the other hand, the particle flux depends only slightly on the gas pulse frequency. The explanation based on cooling and thermalization of sputtered particles is discussed in the paper.

  2. Studies on gas breakdown in pulsed radio frequency atmospheric pressure glow discharges

    SciTech Connect

    Huo, W. G.; Jian, S. J.; Yao, J.; Ding, Z. F.

    2014-05-15

    In pulsed RF atmospheric pressure glow discharges, the gas breakdown judged by the rapid drop in the amplitude of the pulsed RF voltage is no longer universally true. The steep increment of the plasma-absorbed RF power is proposed to determine the gas breakdown. The averaged plasma-absorbed RF power over a pulse period is used to evaluate effects of the preceding pulsed RF discharge on the breakdown voltage of the following one, finding that the breakdown voltage decreases with the increment in the averaged plasma-absorbed RF power under constant pulse duty ratio. Effects of the pulse off-time on the breakdown voltage and the breakdown delay time are also studied. The obtained dependence of the breakdown voltage on the pulse off-time is indicative of the transitional plasma diffusion processes in the afterglow. The breakdown voltage varies rapidly as the plasma diffuses fast in the region of moderate pulse off-time. The contribution of nitrogen atom recombination at the alumina surface is demonstrated in the prolonged memory effect on the breakdown delay time vs. the pulse off-time and experimentally validated by introducing a trace amount of nitrogen into argon at short and long pulse off-times.

  3. A compact repetitive high-voltage nanosecond pulse generator for the application of gas discharge.

    PubMed

    Pang, Lei; Zhang, Qiaogen; Ren, Baozhong; He, Kun

    2011-04-01

    Uniform and stable discharge plasma requires very short duration pulses with fast rise times. A repetitive high-voltage nanosecond pulse generator for the application of gas discharge is presented in this paper. It is constructed with all solid-state components. Two-stage magnetic compression is used to generate a short duration pulse. Unlike in some reported studies, common commercial fast recovery diodes instead of a semiconductor opening switch (SOS) are used in our experiment that plays the role of SOS. The SOS-like effects of four different kinds of diodes are studied experimentally to optimize the output performance. It is found that the output pulse voltage is higher with a shorter reverse recovery time, and the rise time of pulse becomes faster when the falling time of reverse recovery current is shorter. The SOS-like effect of the diodes can be adjusted by changing the external circuit parameters. Through optimization the pulse generator can provide a pulsed voltage of 40 kV with a 40 ns duration, 10 ns rise time, and pulse repetition frequency of up to 5 kHz. Diffuse plasma can be formed in air at standard atmospheric pressure using the developed pulse generator. With a light weight and small packaging the pulse generator is suitable for gas discharge application. PMID:21529005

  4. A compact repetitive high-voltage nanosecond pulse generator for the application of gas discharge

    NASA Astrophysics Data System (ADS)

    Pang, Lei; Zhang, Qiaogen; Ren, Baozhong; He, Kun

    2011-04-01

    Uniform and stable discharge plasma requires very short duration pulses with fast rise times. A repetitive high-voltage nanosecond pulse generator for the application of gas discharge is presented in this paper. It is constructed with all solid-state components. Two-stage magnetic compression is used to generate a short duration pulse. Unlike in some reported studies, common commercial fast recovery diodes instead of a semiconductor opening switch (SOS) are used in our experiment that plays the role of SOS. The SOS-like effects of four different kinds of diodes are studied experimentally to optimize the output performance. It is found that the output pulse voltage is higher with a shorter reverse recovery time, and the rise time of pulse becomes faster when the falling time of reverse recovery current is shorter. The SOS-like effect of the diodes can be adjusted by changing the external circuit parameters. Through optimization the pulse generator can provide a pulsed voltage of 40 kV with a 40 ns duration, 10 ns rise time, and pulse repetition frequency of up to 5 kHz. Diffuse plasma can be formed in air at standard atmospheric pressure using the developed pulse generator. With a light weight and small packaging the pulse generator is suitable for gas discharge application.

  5. Converse Piezoelectricity

    NASA Astrophysics Data System (ADS)

    Springborg, Michael; Kirtman, Bernard

    2013-03-01

    Piezoelectricity results from a coupling between responses to mechanical and electric perturbations and leads to changes in the polarization due to strain or stress or, alternatively, the occurrence of strain as a function of an applied external, electrostatic field (i.e., converse piezoelectricity). Theoretical studies of those properties for extended systems require accordingly that their dipole moment or polarization can be calculated. However, whereas the definition of the operator for the dipole moment for any finite system is trivial, it is only within the last 2 decades that the expressions for the equivalent operator in the independent-particle approximation for the infinite and periodic system have been presented. Here, we demonstrate that the so called branch dependence of the polarization for the infinite, periodic system is related to physical observables in contrast to what often is assumed. This is related to the finding that converse piezoelectric properties depend both on the surfaces of the samples of interest even for samples with size well above the thermodynamic limit. However, we shall demonstrate that these properties can be calculated without explicitly taking the surfaces into account. Both the foundations and results for real system shall be presented.

  6. Probing Pulsed Current Gas Metal Arc Welding for Modified 9Cr-1Mo Steel

    NASA Astrophysics Data System (ADS)

    Krishnan, S.; Kulkarni, D. V.; De, A.

    2015-04-01

    Modified 9Cr-1Mo steels are commonly welded using gas tungsten arc welding process for its superior control over the rate of heat input and vaporization loss of the key alloying elements although the rate electrode deposition remains restricted. Recent developments in pulsed current gas metal arc welding have significantly improved its ability to enhance the rate of electrode deposition with a controlled heat input rate while its application for welding of modified 9Cr-1Mo steels is scarce. The present work reports a detailed experimental study on the pulsed current gas metal arc welding of modified 9Cr-1Mo steels. The effect of the shielding gas, welding current, and speed on the weld bead profile, microstructure and mechanical properties are examined. The results show that the pulsed current gas metal arc welding with appropriate welding conditions can provide acceptable bead profile and mechanical properties in welds of modified 9Cr-1Mo steels.

  7. The influence of gas velocity on surface heat pumping for the orifice pulse tube refrigerator

    NASA Technical Reports Server (NTRS)

    Lee, J. M.; Dill, H. R.

    1990-01-01

    The basic pulse tube refrigerator produces cooling by a mechanism known as surface heat pumping. Cyclical compression and expansion of a gas within an enclosed tube produces large temperature gradients. The purpose of the tube is to act as 'nodal regenerator'. Heat is stored at node positions along the tube wall and is transported between nodes by moving gas parcels. This process gives rise to refrigeration, with hot temperatures at the closed end and cold temperatures at the open end. Unfortunately, much of the available refrigeration is not realized because the closed end of the basic pulse tube restricts gas movement - gas at the extreme temperatures does not come in contact with the heat exchangers. The orifice pulse tube overcomes this limitation by using a valve and surge volume assembly at the warm, closed end. This allows for a residual gas velocity to remain present during the heat transfer process, thereby permitting more gas to exchange heat at the heat exchangers. This paper describes the pulse tube as a nodal regenerator and the effect residual gas velocity has on the heat transfer mechanism of the orifice pulse tube.

  8. Photoionization of noble-gas atoms by ultrashort electromagnetic pulses

    SciTech Connect

    Astapenko, V. A. Svita, S. Yu.

    2014-11-15

    The photoionization of atoms of noble gases (Ar, Kr, and Xe) by ultrashort electromagnetic pulses of a corrected Gaussian shape is studied theoretically. Computations are performed in the context of perturbation theory using a simple expression for the total probability of photoionization of an atom by electromagnetic pulses. The features of this process are revealed and analyzed for various ranges of the parameters of the problem.

  9. Quenching Plasma Waves in Two Dimensional Electron Gas by a Femtosecond Laser Pulse

    NASA Astrophysics Data System (ADS)

    Shur, Michael; Rudin, Sergey; Greg Rupper Collaboration; Andrey Muraviev Collaboration

    Plasmonic detectors of terahertz (THz) radiation using the plasma wave excitation in 2D electron gas are capable of detecting ultra short THz pulses. To study the plasma wave propagation and decay, we used femtosecond laser pulses to quench the plasma waves excited by a short THz pulse. The femtosecond laser pulse generates a large concentration of the electron-hole pairs effectively shorting the 2D electron gas channel and dramatically increasing the channel conductance. Immediately after the application of the femtosecond laser pulse, the equivalent circuit of the device reduces to the source and drain contact resistances connected by a short. The total response charge is equal to the integral of the current induced by the THz pulse from the moment of the THz pulse application to the moment of the femtosecond laser pulse application. This current is determined by the plasma wave rectification. Registering the charge as a function of the time delay between the THz and laser pulses allowed us to follow the plasmonic wave decay. We observed the decaying oscillations in a sample with a partially gated channel. The decay depends on the gate bias and reflects the interplay between the gated and ungated plasmons in the device channel. Army Research Office.

  10. Treatment of Dye Wastewater by Using a Hybrid Gas/Liquid Pulsed Discharge Plasma Reactor

    NASA Astrophysics Data System (ADS)

    Lu, Na; Li, Jie; Wu, Yan; Masayuki, Sato

    2012-02-01

    A hybrid gas/liquid pulsed discharge plasma reactor using a porous ceramic tube is proposed for dye wastewater treatment. High voltage pulsed discharge plasma was generated in the gas phase and simultaneously the plasma channel was permeated through the tiny holes of the ceramic tube into the water phase accompanied by gas bubbles. The porous ceramic tube not only separated the gas phase and liquid phase but also offered an effective plasma spreading channel. The effects of the peak pulse voltage, additive gas varieties, gas bubbling rate, solution conductivity and TiO2 addition were investigated. The results showed that this reactor was effective for dye wastewater treatment. The decoloration efficiency of Acid Orange II was enhanced with an increase in the power supplied. Under the studied conditions, 97% of Acid Orange II in aqueous solution was effectively decolored with additive oxygen gas, which was 51% higher than that with argon gas, and the increasing O2 bubbling rate also benefited the decoloration of dye wastewater. Water conductivity had a small effect on the level of decoloration. Catalysis of TiO2 could be induced by the pulsed discharge plasma and addition of TiO2 aided the decoloration of Acid Orange II.

  11. Pulsed-field-gradient measurements of time-dependent gas diffusion

    NASA Technical Reports Server (NTRS)

    Mair, R. W.; Cory, D. G.; Peled, S.; Tseng, C. H.; Patz, S.; Walsworth, R. L.

    1998-01-01

    Pulsed-field-gradient NMR techniques are demonstrated for measurements of time-dependent gas diffusion. The standard PGSE technique and variants, applied to a free gas mixture of thermally polarized xenon and O2, are found to provide a reproducible measure of the xenon diffusion coefficient (5.71 x 10(-6) m2 s-1 for 1 atm of pure xenon), in excellent agreement with previous, non-NMR measurements. The utility of pulsed-field-gradient NMR techniques is demonstrated by the first measurement of time-dependent (i.e., restricted) gas diffusion inside a porous medium (a random pack of glass beads), with results that agree well with theory. Two modified NMR pulse sequences derived from the PGSE technique (named the Pulsed Gradient Echo, or PGE, and the Pulsed Gradient Multiple Spin Echo, or PGMSE) are also applied to measurements of time dependent diffusion of laser polarized xenon gas, with results in good agreement with previous measurements on thermally polarized gas. The PGMSE technique is found to be superior to the PGE method, and to standard PGSE techniques and variants, for efficiently measuring laser polarized noble gas diffusion over a wide range of diffusion times. Copyright 1998 Academic Press.

  12. Aluminium nitride piezoelectric thin films reactively deposited in closed field unbalanced magnetron sputtering for elevated temperature 'smart' tribological applications

    NASA Astrophysics Data System (ADS)

    Hasheminiasari, Masood

    "Smart" high temperature piezoelectric aluminum nitride (AlN) thin films were synthesized by reactive magnetron sputtering using DC; pulsed-DC, and deep oscillation modulated pulsed power (DOMPP) systems on variety of substrate materials. Process optimization was performed to obtain highly c-axis texture films with improved piezoelectric response via studying the interplay between process parameters, microstructure and properties. AlN thin films were sputtered with DC and pulsed-DC systems to investigate the effect of various deposition parameters such as reactive gas ratio, working pressure, target power, pulsing frequency, substrate bias, substrate heating and seed layers on the properties and performance of the film device. The c-axis texture, orientation, microstructure, and chemical composition of AlN films were characterized by means of X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), and x-ray photoelectron spectroscopy (XPS). A Michelson laser interferometer was designed and built to obtain the converse piezoelectric response of the deposited AlN thin films. Thin films with narrow AlN-(002) rocking curve of 2.5° were obtained with preliminary studies of DOMPP reactive sputtering. In-situ high temperature XRD showed excellent thermal stability and oxidation resistance of AlN films up to 1000 °C. AlN films with optimized processing parameters yielded an inverse piezoelectric coefficient, d33 of 4.9 pm/V close to 90 percent of its theoretical value.

  13. Pulse Compression of CO2 laser in SF6 and it's Mixtures with Dymel Gas

    NASA Astrophysics Data System (ADS)

    Yi, Dechang; Mahajan, Satish

    2003-10-01

    Laser pulse compression using OFID in ammonia, and CH3F gases has been reported in the past. Recent work in dymel gas indicated a four times sharper pulse than that in vacuum [1]. In the present work, experiments were conducted in SF6 gas to investigate the possibility of an OFID effecting a compressed CO2 laser pulse. An average of fourty laser pulses was acquired at a typical gas pressure in the test cell. Pressure of SF6 was varied from 0 to 2.5 torr while that of dymel (in a mixture with SF6) was varied from 0 to 6 torr. Pressure of SF6 was limited to a maximum of 2.5 torr due to strong absorption leading to weakening of output pulse. Results indicate that the addition of SF6 to dymel led to a variation in sharpness (intensity divided by pulsewidth) of a pulse and also to a shift in pressure at which maximum compression in dymel normally occurs. [1]D. Yi, and S.Mahajan,"Pulse Compression of CO2 laser by Optical Free Induction decay (OFID) Effect, Bulletin of APS,Vol.47,No.7,October 2002,pp.27,

  14. Tilted femtosecond pulses for velocity matching in gas-phase ultrafast electron diffraction

    NASA Astrophysics Data System (ADS)

    Zhang, Ping; Yang, Jie; Centurion, Martin

    2014-08-01

    Recent advances in pulsed electron gun technology have resulted in femtosecond electron pulses becoming available for ultrafast electron diffraction experiments. For experiments investigating chemical dynamics in the gas phase, the resolution is still limited to picosecond time scales due to the velocity mismatch between laser and electron pulses. Tilted laser pulses can be used for velocity matching, but thus far this has not been demonstrated over an extended target in a diffraction setting. We demonstrate an optical configuration to deliver high-intensity laser pulses with a tilted pulse front for velocity matching over the typical length of a gas jet. A laser pulse is diffracted from a grating to introduce angular dispersion, and the grating surface is imaged on the target using large demagnification. The laser pulse duration and tilt angle were measured at and near the image plane using two different techniques: second harmonic cross correlation and an interferometric method. We found that a temporal resolution on the order of 100 fs can be achieved over a range of approximately 1 mm around the image plane.

  15. CFD simulation of the gas flow in a pulse tube cryocooler with two pulse tubes

    NASA Astrophysics Data System (ADS)

    Yin, C. L.

    2015-12-01

    In this paper, in order to instruct the next optimization work, a two-dimension Computational Fluid Dynamics (CFD) model is developed to simulate temperature distribution and velocity distribution of oscillating fluid in the DPTC by individual phase-shifting. It is found that the axial temperature distribution of regenerator is generally uniform and the temperatures near the center at the same cross setion of two pulse tubes are obviously higher than their near wall temperatures. The wall temperature difference about 0-7 K exists between the two pulse tubes. The velocity distribution near the center of the regenerator is uniform and there is obvious injection stream coming at the center of the pulse tubes from the hot end. The formation reason of temperature distribution and velocity distribution is explained.

  16. Gas flow stabilized megavolt spark gap for repetitive pulses

    DOEpatents

    Lawson, Robert N.; O'Malley, Martin W.; Rohwein, Gerald J.

    1986-01-01

    A high voltage spark gap switch including a housing having first and second end walls being spaced apart by a predetermined distance. A first electrode is positioned on the first end wall and a second electrode is positioned on the second end wall. The first and second electrodes are operatively disposed relative to each other and are spaced apart by a predetermined gap. An inlet conduit is provided for supplying gas to the first electrode. The conduit includes a nozzle for dispersing the gas in the shape of an annular jet. The gas is supplied into the housing at a predetermined velocity. A venturi housing is disposed within the second electrode. An exhaust conduit is provided for discharging gas and residue from the housing. The gas supplied at the predetermined velocity to the housing through the inlet conduit and the nozzle in an annular shape traverses the gap between the first and second electrodes and entrains low velocity gas within the housing decreasing the velocity of the gas supplied to the housing and increasing the diameter of the annular shape. The venturi disposed within the second electrode recirculates a large volume of gas to clean and cool the surface of the electrodes.

  17. Gas flow stabilized megavolt spark gap for repetitive pulses

    DOEpatents

    Lawson, R.N.; O'Malley, M.W.; Rohwein, G.J.

    A high voltage spark gap switch is disclosed including a housing having first and second end walls being spaced apart by a predetermined distance. A first electrode is positioned on the first end wall and a second electrode is positioned on the second end wall. The first and second electrodes are operatively disposed relative to each other and are spaced apart by a predetermined gap. An inlet conduit is provided for supplying gas to the first electrode. The conduit includes a nozzle for dispersing the gas in the shape of an annular jet. The gas is supplied into the housing at a predetermined velocity. A venturi housing is disposed within the second electrode. An exhaust conduit is provided for discharging gas and residue from the housing. The gas supplied at the predetermined velocity to the housing through the inlet conduit and the nozzle in an annular shape traverses the gap between the first and second electrodes and entrains low velocity gas within the housing decreasing the velocity of the gas supplied to the housing and increasing the diameter of the annular shape. The venturi disposed within the second electrode recirculates a large volume of gas to clean and cool the surface of the electrodes.

  18. Pulse

    MedlinePlus

    Heart rate; Heart beat ... The pulse can be measured at areas where an artery passes close to the skin. These areas include the: ... side of the foot Wrist To measure the pulse at the wrist, place the index and middle ...

  19. A method for removal of CO from exhaust gas using pulsed corona discharge.

    PubMed

    Li, X; Yang, L; Lei, Y; Wang, J; Lu, Y

    2000-10-01

    An experimental study of the oxidation of CO in exhaust gas from a motorcycle has been carried out using plasma chemical reactions in a pulsed corona discharge. In the process, some main parameters, such as the initial CO concentration, amplitude and frequency of pulses, residence time, reactor volume, and relative humidity (RH), as well as their effects on CO removal characteristics, were investigated. O3, which is beneficial to reducing CO, was produced during CO removal. When the exhaust gas was at ambient temperature, more than 80% CO removal efficiency was realized at an initial concentration of 288 ppm in a suitable range of the parameters. PMID:11288300

  20. Flue-gas cleaning using heterogeneously pulsed discharge

    NASA Astrophysics Data System (ADS)

    Yankelevitch, E.; Bystritskii, Vitaly M.; Sinebryukhov, A. V.; Akishev, Yurii

    1995-03-01

    A new promising electro physical method for cleaning flue gases from sulfur and nitrogen oxides has been proposed. This method is based on the initiation of repetitive arc micro discharges in an air-water mixture. The report gives a description of the setup used in an experimental verification of the method, the experimental results obtained, and the results of their analyses. It has been demonstrated that the proposed method has some advantages over other electro physical methods, such as simplicity to realize and operability in a highly humidified gas stream, which substantially extends the realize of its possible applications. The energy required to remove harmful impurity is 200 eV/mol and 23 eV/mol for gas mixtures with NO and SO2, respectively, which is an excellent result for an electro physical method of gas cleaning.

  1. Enhanced ferroelectric and piezoelectric response in Mn-doped Bi0.5Na0.5TiO3-BaTiO3 lead-free film by pulsed laser deposition

    NASA Astrophysics Data System (ADS)

    Jin, Chengchao; Wang, Feifei; Leung, Chung Ming; Yao, Qirong; Tang, Yanxue; Wang, Tao; Shi, Wangzhou

    2013-10-01

    Mn-doped Bi0.5Na0.5TiO3-BaTiO3 thin film with the composition around the morphotropic phase boundary was grown on Pt-electrodized Si substrate by pulsed laser deposition. Highly (1 0 0)-oriented film with pure perovskite structure was obtained through carefully controlling the growth conditions. Well-defined ferroelectric P-E loop was obtained with the average remnant polarization Pr and coercive field Ec of ∼11.3 μC/cm2 and ∼6.5 kV/mm, respectively. Polycrystalline structures and multidomain states were revealed by piezoresponse force microscopy and large local strain response was obtained with the normalized strain Smax/Emax up to 92 pm/V. The excellent global electrical properties make it quite promising in environmental-friendly ferroelectric and piezoelectric devices.

  2. Design and Construction of a High Voltage Pulsed Source for Electric Excitation of the Gas Laser

    NASA Astrophysics Data System (ADS)

    Díaz, Xavier Daza; Neira, Oscar León B.; Díaz-Pérez, H. Abraham

    2008-04-01

    In this paper, the design, construction and implementation of High Voltage Pulsed Source for Electrical Excitation of the Gas Lasers, as a first phase of the research project "Design and Construction of an economically and reliable Laser System constituted by a molecular pulsed laser and a single optical head for dyes" is presented. We proposed and considered the design and the construction of a source of pulsed high voltage that adjusts to the requirements of the pumping system that requires a low pressure nitrogen laser. The design and construction of the source high voltage prototype is presented like part of the electrical pumping system for a Pulsed Nitrogen Laser. The electrical pumping System is conformed by three subsystems: the high pulsed regulated voltage Source, the storage and unloading system of electrical energy of active medium, and the frequency control system of discharge repetition (spark gap) constituted by a circuit RLC and the electrodes of the laser discharge tube. In the present work the aspects related to the pulsed high regulated voltage Source is presented, Our Source of high pulsed voltage is constituted by four fundamental stages: the Stage of Conversion AC-DC (voltage reducer), the Stage of Commutation by means of a Insulated Gate Bipolar Transistor (IGBT), the stage of Generation of signal modulated by the pulses width "PWM" (with base to Circuit TL 494) and the Stage of Elevation of Voltage (using a FlyBack Transformer).

  3. The development of a pulsed laser imaging system for natural gas leak detection

    NASA Astrophysics Data System (ADS)

    Kulp, Thomas J.

    The detection of gas leaks represents a critical operation performed regularly by the gas industry to maintain the integrity and safety of its vast network of piping, both above and below the ground. We are developing a technology that allows the real-time imaging of gas plumes in a television format. Termed backscatter absorption gas imaging (BAGI), the technique operates by illuminating a scene with infrared laser radiation having a wavelength that is absorbed by the gas to be detected (in this case, methane). Backscattered laser radiation is used to create a video image of the scene. If a leak of the target gas is present in the field-of-view of the camera, it attenuates a portion of the backscatter and creates a dark cloud in the video picture. The specific purpose of this project is to investigate a new method of accomplishing BAGI using a pulsed laser source. The pulsed laser imager under development in this project is expected to have a range (greater than or equal to 40 m) and sensitivity (less than 10 ppm-m) that will surpass the respective attributes of a scanned continuous wave laser imager. The pulsed system will operate by flooding (rather than scanning) the imaged scene with pulses of laser radiation. Imaging will be accomplished using a focal-plane array camera that operates in a snapshot format. The higher power of the pulsed laser source and the more effective collection optics of the focal-plane array-based receiver will allow the performance enhancements to be achieved.

  4. Propagation of the pulsed electron beam of nanosecond duration in gas composition of high pressure

    NASA Astrophysics Data System (ADS)

    Kholodnaya, G.; Sazonov, R.; Ponomarev, D.; Remnev, G.

    2015-11-01

    This paper presents the results of the investigation of the propagation of an electron beam in the high-pressure gas compositions (50, 300, and 760 Torr): sulfur hexafluoride and hydrogen, sulfur hexafluoride and nitrogen, sulfur hexafluoride and argon. The experiments have been performed using the TEA-500 laboratory accelerator. The main parameters of the accelerator are as follows: an accelerating voltage of 500 kV; an electron beam current of 10 kA; a pulse width at half maximum of 60 ns; a pulse energy of 200 J; a pulse repetition rate of up to 5 pulses per second, a beam diameter of 5 cm. The pulsed electron beam was injected into a 55 cm metal drift tube. The drift tube is equipped with three reverse-current shunts with simultaneous detecting of signals. The obtained results of the investigation make it possible to conclude that the picture of the processes occurring in the interaction of an electron beam in the high-pressure gas compositions is different from that observed in the propagation of the electron beam in the low-pressure gas compositions (1 Torr).

  5. Pulsed flashover of solid dielectric materials in compressed gas environment

    SciTech Connect

    Tewari, Somesh Vinayak E-mail: svtewari@barc.gov.in; Sharma, Archana; Mittal, K. C.

    2015-06-24

    An experimental investigation of surface flashover characteristics of PMMA and POM is studied in compressed nitrogen gas environment with nitrogen as the background gas. The operating pressure range is from 1kg/cm{sup 2} to 4kg/cm{sup 2}. It is observed that the breakdown voltage of PMMA is higher than POM owing to a higher permittivity mismatch between POM- nitrogen interface as compared to the PMMA- nitrogen interface. The reduction in spacer efficiency with pressure for PMMA is 11% as compared to POM which shows a higher reduction of 18%. This paper further emphasizes on the role of energy level and density of charge carrier trapping centers for a reduced breakdown voltage in POM as compared to PMMA.

  6. Time resolved Thomson scattering diagnostic of pulsed gas metal arc welding (GMAW) process

    NASA Astrophysics Data System (ADS)

    Kühn-Kauffeldt, M.; Marquès, J. L.; Schein, J.

    2014-11-01

    In this work a Thomson scattering diagnostic technique was applied to obtain time resolved electron temperature and density values during a gas metal arc welding (GMAW) process. The investigated GMAW process was run with aluminum wire (AlMg 4,5 Mn) with 1.2 mm diameter as a wire electrode, argon as a shielding gas and peak currents in the range of 400 A. Time resolved measurements could be achieved by triggering the laser pulse at shifted time positions with respect to the current pulse driving the process. Time evaluation of resulting electron temperatures and densities is used to investigate the state of the plasma in different phases of the current pulse and to determine the influence of the metal vapor and droplets on the plasma properties.

  7. Intense terahertz-pulse generation by four-wave mixing process in induced gas plasma

    NASA Astrophysics Data System (ADS)

    Wicharn, S.; Buranasiri, P.

    2015-08-01

    In this article, we have numerically investigated an intense terahertz (THz) pulses generation in gaseous plasma based on the third-order nonlinear effect, four-wave mixing rectification (FWMR). We have proposed that the fundamental fields and second-harmonic field of ultra-short pulse lasers are combined and focused into a very small gas chamber to induce a gaseous plasma, which intense THz pulse is produced. To understand the THz generation process, the first-order multiple-scale perturbation method (MSPM) has been utilized to derive a set of nonlinear coupled-mode equations for interacting fields such as two fundamental fields, a second-harmonic field, and a THz field. Then, we have simulate the intense THz-pulse generation by using split step-beam propagation method (SS-BPM) and calculated output THz intensities. Finally, the output THz intensities generated from induced air, nitrogen, and argon plasma have been compared.

  8. Pulse-driven micro gas sensor fitted with clustered Pd/SnO2 nanoparticles.

    PubMed

    Suematsu, Koichi; Shin, Yuka; Ma, Nan; Oyama, Tokiharu; Sasaki, Miyuki; Yuasa, Masayoshi; Kida, Tetsuya; Shimanoe, Kengo

    2015-08-18

    Real-time monitoring of specific gas concentrations with a compact and portable gas sensing device is required to sense potential health risk and danger from toxic gases. For such purposes, we developed an ultrasmall gas sensor device, where a micro sensing film was deposited on a micro heater integrated with electrodes fabricated by the microelectromechanical system (MEMS) technology. The developed device was operated in a pulse-heating mode to significantly reduce the heater power consumption and make the device battery-driven and portable. Using clustered Pd/SnO2 nanoparticles, we succeeded in introducing mesopores ranging from 10 to 30 nm in the micro gas sensing film (area: ϕ 150 μm) to detect large volatile organic compounds (VOCs). The micro sensor showed quick, stable, and high sensor responses to toluene at ppm (parts per million) concentrations at 300 °C even by operating the micro heater in a pulse-heating mode where switch-on and -off cycles were repeated at one-second intervals. The high performance of the micro sensor should result from the creation of efficient diffusion paths decorated with Pd sensitizers by using the clustered Pd/SnO2 nanoparticles. Hence we demonstrate that our pulse-driven micro sensor using nanostructured oxide materials holds promise as a battery-operable, portable gas sensing device. PMID:26196499

  9. Pulsed-gas glow discharge for ultrahigh mass resolution measurements with Fourier transform ion cyclotron resonance mass spectrometry

    SciTech Connect

    Watson, C.H.; Eyler, J.R.; Barshick, C.M.; Wronka, J.; Laukien, F.H.

    1996-02-01

    A new pulsed-gas glow discharge (GD) source has been developed for use with an external ion source Fourier transform ion cyclotron resonance (FTICR) mass spectrometer. With pulsed argon gas introduction into the GD source, the gas load and pressure in the mass analyzer region were greatly reduced; this resulted in improved mass resolution. Mass resolution of greater than 145000 (fwhm) has been achieved for Cu{sup +} ions from a brass sample, the highest reported for any type of GD mass spectrometer. The pulsed-gas GD source promises analytical usefulness for ultrahigh resolution measurements in GD mass spectrometry. 16 refs., 3 figs.

  10. Piezoelectric drive circuit

    DOEpatents

    Treu, C.A. Jr.

    1999-08-31

    A piezoelectric motor drive circuit is provided which utilizes the piezoelectric elements as oscillators and a Meacham half-bridge approach to develop feedback from the motor ground circuit to produce a signal to drive amplifiers to power the motor. The circuit automatically compensates for shifts in harmonic frequency of the piezoelectric elements due to pressure and temperature changes. 7 figs.

  11. Piezoelectric drive circuit

    DOEpatents

    Treu, Jr., Charles A.

    1999-08-31

    A piezoelectric motor drive circuit is provided which utilizes the piezoelectric elements as oscillators and a Meacham half-bridge approach to develop feedback from the motor ground circuit to produce a signal to drive amplifiers to power the motor. The circuit automatically compensates for shifts in harmonic frequency of the piezoelectric elements due to pressure and temperature changes.

  12. "Mighty Worm" Piezoelectric Actuator

    NASA Technical Reports Server (NTRS)

    Bamford, Robert M.; Wada, Ben K.; Moore, Donald M.

    1994-01-01

    "Mighty Worm" piezoelectric actuator used as adjustable-length structural member, active vibrator or vibration suppressor, and acts as simple (fixed-length) structural member when inactive. Load force not applied to piezoelectric element in simple-structural-member mode. Piezoelectric element removed from load path when not in use.

  13. Combining transcutaneous blood gas measurement and pulse oximetry.

    PubMed

    Eberhard, Patrick; Gisiger, P A; Gardaz, J P; Spahn, D R

    2002-01-01

    We are describing the preliminary results of tests performed in adult volunteers and in adult patients during and after general anesthesia with a miniaturized single sensor combining the continuous and non-invasive measurement of oxygen saturaiton by pulse oximetry (SpO2) and transcutaneous PCO2 (OxiCarbo sensor). The sensor is heated to 42 degrees C to arterialize the cutaneous tissue and is applied at the ear lobe with a special low-pressure clip. The results indicate a good agreement between ear lobe PCO2 and arterial PCO2 in the range 35 to 70 mmHg (10 patients, number of measurements 104, regression line TcPCO2 = 1.01 PaCO2 + 0.59 mmHg, bias 1.22 mmHg, SD 3.69 mmHg) and between ear lobe SpO2 and SaO2 (bias 0.44% with SD 0.77% in the range 80% to 100%, bias 1.39% with SD 1.43% in the range 60% to 80%). The ear lobe OxiCarbog sensor detects the SpO2 change 5 to 37 sec faster than a finger sensor and the PCO2 change 9 to 48 sec faster than a transcutaneous sensor fixed at the upper arm. Further improvements versus single sensors are a higher stability of the SpO2 signal and the possibility of performing long term SpO2 and PCO2 measurement at the ear lobe. PMID:11900043

  14. Attosecond pulses generated by the lighthouse effect in Ar gas

    NASA Astrophysics Data System (ADS)

    Tosa, Valer; Lee, Ji Su; Kim, Hyung Taek; Nam, Chang Hee

    2015-05-01

    We numerically investigate harmonic generation in Ar gas under high ionization conditions and demonstrate that a lighthouse effect is present. We examine the structure of the driving field during propagation in temporal, spectral, and spatial domains, and conclude that the complete depletion of neutral Ar on axis gives rise to additional wavelets at off-axis regions. We show that these wavelets propagate with increasing divergence as the radial distances from the axis increase, generating the rotation of the wave front, thus fulfilling a necessary condition for the lighthouse effect. We obtain attosecond bursts of light emitted with different divergences in successive optical half-cycles so that in the far field these bursts arrive at different distances from the beam axis.

  15. Effect of laser pulse energy on the laser ignition of compressed natural gas fueled engine

    NASA Astrophysics Data System (ADS)

    Srivastava, Dhananjay Kumar; Wintner, Ernst; Agarwal, Avinash Kumar

    2014-05-01

    Laser pulses of few a nanoseconds' duration are focused by an appropriate converging lens system, leading to breakdown of the medium (combustible gases), resulting in the formation of intense plasma. Plasma thus induced can be used to initiate the combustion of combustible air-fuel mixtures in a spark ignition engine provided the energy of the plasma spark is high enough. Laser ignition has several advantages over the conventional spark ignition system, especially in case of lean air-fuel mixture. In this study, laser ignition of compressed natural gas was investigated in a constant volume combustion chamber (CVCC) as well as in a single-cylinder engine. Flame kernel visualizations for different pulse energy of natural gas-air mixtures were carried out in the CVCC. The images of the development of early flame kernel stages and its growth with time were recorded by shadowgraphy technique. The effect of laser pulse energy on the engine combustion, performance, and emissions was investigated using different air-fuel mixtures. Increased peak cylinder pressure, higher rate of heat release, faster combustion, and increased combustion stability were observed for higher laser pulse energies. The effect of laser pulse energy on the engine-out emissions was also investigated in this study.

  16. Parameter sensitivity analysis of tailored-pulse loading stimulation of Devonian gas shale

    SciTech Connect

    Barbour, T.G.; Mihalik, G.R.

    1980-11-01

    An evaluation of three tailored-pulse loading parameters has been undertaken to access their importance in gas well stimulation technology. This numerical evaluation was performed using STEALTH finite-difference codes and was intended to provide a measure of the effects of various tailored-pulse load configurations on fracture development in Devonian gas shale. The three parameters considered in the sensitivity analysis were: loading rate; decay rate; and sustained peak pressures. By varying these parameters in six computations and comparing the relative differences in fracture initiation and propagation the following conclusions were drawn: (1) Fracture initiation is directly related to the loading rate aplied to the wellbore wall. Loading rates of 10, 100 and 1000 GPa/sec were modeled. (2) If yielding of the rock can be prevented or minimized, by maintaining low peak pressures in the wellbore, increasing the pulse loading rate, to say 10,000 GPa/sec or more, should initiate additional multiple fractures. (3) Fracture initiation does not appear to be related to the tailored-pulse decay rate. Fracture extension may be influenced by the rate of decay. The slower the decay rate, the longer the crack extension. (4) Fracture initiation does not appear to be improved by a high pressure plateau in the tailored-pulse. Fracture propagation may be enhanced if the maintained wellbore pressure plateau is of sufficient magnitude to extent the range of the tangential tensile stresses to greater radial distances. 26 figures, 2 tables.

  17. Theoretical analysis of fluorescence signals in filamentation of femtosecond laser pulses in nitrogen molecular gas

    SciTech Connect

    Arevalo, E.; Becker, A.

    2005-10-15

    We study numerically and analytically the role of the combined effect of self-focusing, geometrical focusing, and the plasma defocusing in the formation of the fluorescence signal during the filamentation of a Ti:sapphire laser pulse in nitrogen molecular gas. Results of numerical simulations are used to estimate the number of excited ions in the focal volume, which is proportional to the fluorescence signal. We find good agreement between the theoretical results and the experimental data, showing that such data can be used to get further insight into the effective focal volume during filamentation of femtosecond laser pulses in transparent media.

  18. Channel Formation in Long Laser Pulse Interaction with a Helium Gas Jet

    SciTech Connect

    Malka, V.; De Wispelaere, E.; Amiranoff, F.; Baton, S.; Bonadio, R.; Coulaud, C.; Haroutunian, R.; Modena, A.; Puissant, D.; Stenz, C.; Hueller, S.; Casanova, M.

    1997-10-01

    Experimental realization of an electron density channel created by a low intensity laser in a helium gas jet is presented. The long (2.5mm) plasma channel is fully ionized and thus prevents undesirable refraction effects for propagation and guiding of a subsequent high intensity laser pulse. The channel parameters are easily controlled and well suited for laser guiding. The radial plasma expansion and the temperature evolution have been measured and compared to hydrodynamic simulations which show that the plasma expansion is governed by a thermal wave during the laser pulse. {copyright} {ital 1997} {ital The American Physical Society}

  19. Effect of current waveforms on metal transfer in pulsed gas metal arc welding

    NASA Astrophysics Data System (ADS)

    Wu, C. S.; Chen, M. A.; Lu, Y. F.

    2005-12-01

    With new types of welding power supply based on higher performance power electronic devices and digital control techniques, advanced pulse waveforms can be produced to offer more characteristics that can be fine tuned to optimize the welding process. In this paper, pulsed current waveforms with four basic parameters and six secondary parameters are used to study the effect of waveform parameters on the mode of metal transfer in pulsed gas metal arc welding (GMAW-P). An experimental system is developed to sense, observe and analyse the images of droplet/wire, and the transient data of welding current and arc voltage. Experiments are conducted to study the influence of the ratio of the pulsing-current time to the droplet-detachment time as well as the droplet-detachment current level on the mode of metal transfer. Appropriate sets of welding conditions including pulse waveform and parameters are obtained to achieve the ideal transfer mode of one-droplet-per-pulse in GMAW-P.

  20. Pulse

    MedlinePlus

    ... resting for at least 10 minutes. Take the exercise heart rate while you are exercising. ... pulse rate can help determine if the patient's heart is pumping. ... rate gives information about your fitness level and health.

  1. Histogrammatic Method for Determining Relative Abundance of Input Gas Pulse

    NASA Technical Reports Server (NTRS)

    Mandrake, Lukas; Bornstein, Benjamin J.; Madzunkov, Stojan; MacAskill, John A.

    2012-01-01

    To satisfy the Major Constituents Analysis (MCA) requirements for the Vehicle Cabin Atmosphere Monitor (VCAM), this software analyzes the relative abundance ratios for N2, O2, Ar, and CO2 as a function of time and constructs their best-estimate mean. A histogram is first built of all abundance ratios for each of the species vs time. The abundance peaks corresponding to the intended measurement and any obfuscating background are then separated via standard peak-finding techniques in histogram space. A voting scheme is then used to include/exclude this particular time sample in the final average based on its membership to the intended measurement or the background population. This results in a robust and reasonable estimate of the abundance of trace components such as CO2 and Ar even in the presence of obfuscating backgrounds internal to the VCAM device. VCAM can provide a means for monitoring the air within the enclosed environments, such as the ISS (International Space Station), Crew Exploration Vehicle (CEV), a Lunar Habitat, or another vehicle traveling to Mars. Its miniature pre-concentrator, gas chromatograph (GC), and mass spectrometer can provide unbiased detection of a large number of organic species as well as MCA analysis. VCAM s software can identify the concentration of trace chemicals and whether the chemicals are on a targeted list of hazardous compounds. This innovation s performance and reliability on orbit, along with the ground team s assessment of its raw data and analysis results, will validate its technology for future use and development.

  2. Simultaneous, single-pulse, synchrotron x-ray imaging and diffraction under gas gun loading.

    PubMed

    Fan, D; Huang, J W; Zeng, X L; Li, Y; E, J C; Huang, J Y; Sun, T; Fezzaa, K; Wang, Z; Luo, S N

    2016-05-01

    We develop a mini gas gun system for simultaneous, single-pulse, x-ray diffraction and imaging under high strain-rate loading at the beamline 32-ID of the Advanced Photon Source. In order to increase the reciprocal space covered by a small-area detector, a conventional target chamber is split into two chambers: a narrowed measurement chamber and a relief chamber. The gas gun impact is synchronized with synchrotron x-ray pulses and high-speed cameras. Depending on a camera's capability, multiframe imaging and diffraction can be achieved. The proof-of-principle experiments are performed on single-crystal sapphire. The diffraction spots and images during impact are analyzed to quantify lattice deformation and fracture; fracture is dominated by splitting cracks followed by wing cracks, and diffraction peaks are broadened likely due to mosaic spread. Our results demonstrate the potential of such multiscale measurements for studying high strain-rate phenomena at dynamic extremes. PMID:27250438

  3. Superhard Coatings Synthesis Assisted by Pulsed Beams of High-Energy Gas Molecules

    NASA Astrophysics Data System (ADS)

    Metel, Alexander; Bolbukov, Vasily; Volosova, Marina; Grigoriev, Sergei; Melnik, Yury; Department of high-efficiency machining technologies Team

    2015-09-01

    For production of nanocomposite superhard (HV 5000) and fracture-tough coatings on dielectric substrates a source of metal atoms accompanied by pulsed beams of 30-keV neutral molecules was used. The source is equipped with two parallel equipotential grids placed between a magnetron target and a substrate. Negative high-voltage pulses applied to the high-transparency grids accelerate from the magnetron plasma ions, which are transformed into high-energy neutral molecules due to charge-exchange collisions with gas molecules between the grids. Mixing of the substrate and coating materials through bombardment by high-energy gas molecules results in an adequate compressive stress of the coating and interface width exceeding 1 μm, which allows deposition of 100- μm-thick coatings with a perfect adhesion. The work was supported by the Grant No. 14-29-00297 of the Russian Science Foundation.

  4. Standardized piezoelectric polymer (PVDF) gauge for detonator response measurement

    SciTech Connect

    Moore, L.M.; Graham, R.A.; Reed, R.P.; Lee, L.M.; Bauer, F.; Warren, T.W.

    1989-01-01

    Time-resolved measurements of pressure profiles from the detonation of explosive devices have proven to be essential for detailed study of device performance. At present such measurements are routinely carried out with laser velocity interferometer (VISAR) systems, electromagnetic particle velocity gauges or piezoresistant (Manganin) gauges. One of the most promising new gauges to appear in recent years is the piezoelectric polymer gauge (PVDF) which has been standardized for general use based on the materials processing techniques developed by Bauer. The special problems presented by small size piezoelectric polymer gauges and nonplanar impacts are studied over a range of impact conditions. The response of 1 mm by 1 mm active area PVDF gauges under precisely controlled compressed-gas gun impacts shows highly reproducible results to pressures of 20 GPa. For the PVDF gauge which is placed within 12 microns of the impact surface and under approximately planar loading with small detonator flyer plates, PVDF gauge signals appear to be reduced by about 15% compared to the compressed-gas gun loading response. For highly nonplanar flyer impacts the PVDF signals are reduced by about 35%. In all stress environments, high quality, time-resolved current pulses are observed. 13 refs., 10 figs., 2 tabs.

  5. LPS levels in root canals after the use of ozone gas and high frequency electrical pulses.

    PubMed

    Melo, Tiago André Fontoura de; Gründling, Grasiela Sabrina Longhi; Montagner, Francisco; Scur, Alcione Luiz; Steier, Liviu; Scarparo, Roberta Kochenborger; Figueiredo, José Antônio Poli de; Vier-Pelisser, Fabiana Vieira

    2016-01-01

    The present study aims to verify the effect of ozone gas (OZY® System) and high frequency electric pulse (Endox® System) systems on human root canals previously contaminated with Escherichia colilipopolysaccharide (LPS). Fifty single-rooted teeth had their dental crowns removed and root lengths standardized to 16 mm. The root canals were prepared up to #60 hand K-files and sterilized using gamma radiation with cobalt 60. The specimens were divided into the following five groups (n = 10) based on the disinfection protocol used: OZY® System, one 120-second-pulse (OZY 1p); OZY® System, four 24-second-pulses (OZY 4p); and Endox® System (ENDOX). Contaminated and non-contaminated canals were exposed only to apyrogenic water and used as positive (C+) and negative (C-) controls, respectively. LPS (O55:B55) was administered in all root canals except those belonging to group C-. After performing disinfection, LPS samples were collected from the canals using apyrogenic paper tips. Limulus Amoebocyte Lysate (LAL) was used to quantify the LPS levels, and the data obtained was analyzed using one-way ANOVA. The disinfection protocols used were unable to reduce the LPS levels significantly (p = 0.019). The use of ozone gas and high frequency electric pulses was not effective in eliminating LPS from the root canals. PMID:26981752

  6. Multifrequency laser probing of CO-containing gas mixtures excited in a pulsed discharge

    SciTech Connect

    Ionin, Andrei A; Klimachev, Yu M; Kozlov, A Yu; Kotkov, A A; Rulev, O A; Seleznev, L V; Sinitsyn, D V

    2007-03-31

    The method of multifrequency laser probing is developed which can be used for diagnostics of the temperature and population of vibrational levels in gas mixtures containing CO molecules in excited vibrational states. The method is tested by studying the dynamics of the gas temperature and population of vibrational levels of the CO molecule in gas mixtures excited by a pulsed discharge. It is shown that the method provides the reduction of the gas temperature measurement error down to 3%. It is found that the population of lower vibrational levels in the CO-O{sub 2} mixture can exceed the population of levels in CO-He and CO-N{sub 2} laser mixtures by several times. (active media)

  7. Charge exchange of laser-produced ions in a pulsed gas jet

    NASA Astrophysics Data System (ADS)

    Shaikhislamov, I. F.; Ponomarenko, A. G.; Antonov, V. M.; Boyarintsev, E. L.; Posukh, V. G.; Melekhov, A. V.

    2007-10-01

    Results of an experiment on the interaction of laser-produced plasma with a pulsed gas jet are reported. A resonant charge-exchange pumping of the n=3 level of the C3+ ion was observed. A spatial structure of the region of intensive interaction was obtained by a short time imaging of filtered plasma radiation. According to independent probe measurements, the interaction was realized at densities of ions and gas particles in excess of 1016 cm-3. The obtained data provide a prospect for future experiments on laser gain in the EUV spectral range based on charge-exchange pumping of the C5+ ion.

  8. Real Gas Effects on the Performance of Hydrocarbon-fueled Pulse Detonation Engines

    NASA Technical Reports Server (NTRS)

    Povinelli, Louis A.; Yungster, Shaye

    2003-01-01

    This paper presents results for a single-pulse detonation tube wherein the effects of high temperature dissociation and the subsequent recombination influence the sensible heat release available for providing propulsive thrust. The study involved the use of ethylene and air at equivalence ratios of 0.7 and 1.0. The real gas effects on the sensible heat release were found to be significantly large so as to have an impact on the thrust, impulse and fuel consumption of a PDE.

  9. Piezoelectrically assisted ultrafiltration

    SciTech Connect

    Ahner, N.; Gottschlich, D.; Narang, S.; Roberts, D.; Sharma, S.; Ventura, S.

    1993-01-01

    The authors have demonstrated the feasibility of using piezoelectrically assisted ultrafiltration to reduce membrane fouling and enhance the flux through ultrafiltration membranes. A preliminary economic evaluation, accounting for the power consumption of the piezoelectric driver and the extent of permeate flow rate enhancement, has also shown that piezoelectrically assisted ultrafiltration is cost effective and economically competitive in comparison with traditional separation processes. Piezoelectric transducers, such as a piezoelectric lead zirconate titanate (PZT) disc or a piezoelectric horn, driven by moderate power, significantly enhance the permeate flux on fouled membranes, presumably because they promote local turbulence. Several experiments were conducted on polysulfone and regenerated cellulose UF membranes fouled during filtration of model feed solutions. Solutions of poly(ethylene glycol) and of high-molecular weight dextran were used as models. The authors found that they could significantly increase the permeate flux by periodically driving the piezoelectric transducer, horn or PZT disc, by application of moderate power over short periods of time, from 20 to 90 seconds. Enhancements as high as a factor of 8 were recorded within a few seconds, and enhanced permeate fluxes were maintained over a prolonged period (up to 3 hours). The prolonged flux enhancement makes it feasible to drive the piezoelectric transducer intermittently, thereby reducing the power consumption of the piezoelectric driver. As piezoelectric drivers of sonically assisted ultrafiltration, PZT disc transducers are preferred over the piezoelectric horn because of their small size and ease of adaptability to ultrafiltration test cells. The horn transmits sonic energy to the UF membrane through a titanium element driven by a separate piezoelectric transducer, but a piezoelectric ceramic disc transmits energy directly to the UF membrane.

  10. Generation of 12 fs deep-ultraviolet pulses by four-wave mixing through filamentation in neon gas.

    PubMed

    Fuji, Takao; Horio, Takuya; Suzuki, Toshinori

    2007-09-01

    Generation of deep-ultraviolet femtosecond pulses by four-wave mixing through filamentation in neon gas was demonstrated. Fundamental (omega) and second-harmonic (2omega) pulses of 25 fs Ti:sapphire amplifier output were focused into neon gas, and 20 microJ pulses with the center wavelength of 260 nm were produced by a four-wave mixing process, 2omega+2omega-omega?3omega through an ~15 cm filament. Additionally, pulses with an energy of 2 microJ at 200 nm were generated, probably by a cascaded process, 3omega+2omega-omega?4omega. The 260 nm pulses were compressed by a grating-based compressor and characterized by a dispersion-free transient grating frequency-resolved optical gating. The estimated pulse width was 12 fs. PMID:17767278

  11. A piezoelectric transformer

    NASA Technical Reports Server (NTRS)

    Won, C. C.

    1993-01-01

    This work describes a modeling and design method whereby a piezoelectric system is formulated by two sets of second-order equations, one for the mechanical system, and the other for the electrical system, coupled through the piezoelectric effect. The solution to this electromechanical coupled system gives a physical interpretation of the piezoelectric effect as a piezoelectric transformer that is a part of the piezoelectric system, which transfers the applied mechanical force into a force-controlled current source, and short circuit mechanical compliance into capacitance. It also transfers the voltage source into a voltage-controlled relative velocity input, and free motional capacitance into mechanical compliance. The formulation and interpretation simplify the modeling of smart structures and lead to physical insight that aids the designer. Due to its physical realization, the smart structural system can be unconditional stable and effectively control responses. This new concept has been demonstrated in three numerical examples for a simple piezoelectric system.

  12. Coherent Control of Multiphoton Transitions in the Gas and Condensed Phases with Shaped Ultrashort Pulses

    SciTech Connect

    Marcos Dantus

    2008-09-23

    Controlling laser-molecule interactions has become an integral part of developing devices and applications in spectroscopy, microscopy, optical switching, micromachining and photochemistry. Coherent control of multiphoton transitions could bring a significant improvement of these methods. In microscopy, multi-photon transitions are used to activate different contrast agents and suppress background fluorescence; coherent control could generate selective probe excitation. In photochemistry, different dissociative states are accessed through two, three, or more photon transitions; coherent control could be used to select the reaction pathway and therefore the yield-specific products. For micromachining and processing a wide variety of materials, femtosecond lasers are now used routinely. Understanding the interactions between the intense femtosecond pulse and the material could lead to technologically important advances. Pulse shaping could then be used to optimize the desired outcome. The scope of our research program is to develop robust and efficient strategies to control nonlinear laser-matter interactions using ultrashort shaped pulses in gas and condensed phases. Our systematic research has led to significant developments in a number of areas relevant to the AMO Physics group at DOE, among them: generation of ultrashort phase shaped pulses, coherent control and manipulation of quantum mechanical states in gas and condensed phases, behavior of isolated molecules under intense laser fields, behavior of condensed phase matter under intense laser field and implications on micromachining with ultrashort pulses, coherent control of nanoparticles their surface plasmon waves and their nonlinear optical behavior, and observation of coherent Coulomb explosion processes at 10^16 W/cm^2. In all, the research has resulted in 36 publications (five journal covers) and nine invention disclosures, five of which have continued on to patenting

  13. Gas breakdown driven by L band short-pulse high-power microwave

    NASA Astrophysics Data System (ADS)

    Yang, Yi-Ming; Yuan, Cheng-Wei; Qian, Bao-Liang

    2012-12-01

    High power microwave (HPM) driven gas breakdown is a major factor in limiting the radiation and transmission of HPM. A method that HPM driven gas breakdown could be obtained by changing the aperture of horn antenna is studied in this paper. Changing the effective aperture of horn antenna can adjust the electric field in near field zone, leading to gas breakdown. With this method, measurements of air and SF6 breakdowns are carried out on a magnetically insulated transmission-line oscillators, which is capable of generating HPM with pulse duration of 30 ns, and frequency of 1.74 GHz. The typical breakdown waveforms of air and SF6 are presented. Besides, the breakdown field strengths of the two gases are derived at different pressures. It is found that the effects of air and SF6 breakdown on the transmission of HPM are different: air breakdown mainly shortens the pulse width of HPM while SF6 breakdown mainly reduces the peak output power of HPM. The electric field threshold of SF6 is about 2.4 times larger than that of air. These differences suggest that gas properties have a great effect on the transmission characteristic of HPM in gases.

  14. Gas breakdown driven by L band short-pulse high-power microwave

    SciTech Connect

    Yang Yiming; Yuan Chengwei; Qian Baoliang

    2012-12-15

    High power microwave (HPM) driven gas breakdown is a major factor in limiting the radiation and transmission of HPM. A method that HPM driven gas breakdown could be obtained by changing the aperture of horn antenna is studied in this paper. Changing the effective aperture of horn antenna can adjust the electric field in near field zone, leading to gas breakdown. With this method, measurements of air and SF{sub 6} breakdowns are carried out on a magnetically insulated transmission-line oscillators, which is capable of generating HPM with pulse duration of 30 ns, and frequency of 1.74 GHz. The typical breakdown waveforms of air and SF{sub 6} are presented. Besides, the breakdown field strengths of the two gases are derived at different pressures. It is found that the effects of air and SF{sub 6} breakdown on the transmission of HPM are different: air breakdown mainly shortens the pulse width of HPM while SF{sub 6} breakdown mainly reduces the peak output power of HPM. The electric field threshold of SF{sub 6} is about 2.4 times larger than that of air. These differences suggest that gas properties have a great effect on the transmission characteristic of HPM in gases.

  15. Hybrid thermoelectric piezoelectric generator

    NASA Astrophysics Data System (ADS)

    Montgomery, D. S.; Hewitt, C. A.; Carroll, D. L.

    2016-06-01

    This work presents an integration of flexible thermoelectric and piezoelectric materials into a single device structure. This device architecture overcomes several prohibitive issues facing the combination of traditional thermoelectric and piezoelectric generators, while optimizing performance of the combined power output. The structure design uses a carbon nanotube/polymer thin film as a flexible thermoelectric generator that doubles as an electrode on a piezoelectric generator made of poly(vinylidene fluoride). An example 2 × 2 array of devices is shown to generate 89% of the maximum thermoelectric power, and provide 5.3 times more piezoelectric voltage when compared with a traditional device.

  16. Argon gas-puff radius optimiaztion for Saturn operating in the long-pulse mode.

    SciTech Connect

    Apruzese, John P.; Jackson, S. L.; Commisso, Robert J.; Weber, Bruce V.; Mosher, Daniel A.

    2010-06-01

    Argon gas puff experiments using the long pulse mode of Saturn (230-ns rise time) have promise to increase the coupled energy and simplify operations because the voltage is reduced in vacuum and the forward-going energy is higher for the same Marx charge. The issue addressed in this work is to determine if the 12-cm-diameter triple nozzle used in Saturn long-pulse-mode experiments to date provides maximum K-shell yield, or if a different-radius nozzle provides additional radiation. Long-pulse implosions are modeled by starting with measured density distributions from the existing 12-cm-diameter nozzle, and then varying the outer radius in an implosion-energy-conserving self-similar manner to predict the gas-puff diameter that results in the maximum K-shell yield. The snowplow-implosions and multi-zone radiation transport models used in the analysis are benchmarked against detailed measurements from the 12-cm-diameter experiments. These calculations indicate that the maximum K-shell emission is produced with very nearly the existing nozzle radius.

  17. Implosion of reactor-size, gas-filled spherical shell targets driven by shaped pressure pulses

    SciTech Connect

    Piriz, A.R.; Atzeni, S. )

    1993-05-01

    The implosion of a family of reactor-size targets for inertial confinement fusion (ICF) is studied analytically and numerically. The targets consist of a deuterium--tritium (D--T) shell filled with D--T vapor and they are imploded by a multistep pressure pulse designed in such a way that the final hot spot is formed mainly from the initially gaseous fuel. The formation of the hot spot is described by means of a relatively simple model, and scaling laws for the quantities that characterize the state of the initially gaseous part of the fuel prior to ignition are derived. The results of the model are compared with one-dimensional fluid simulations, and good agreement is found. A parametric study of the fuel energy gain is then presented; the dependence of the gain and of the hot spot convergence ratio on the pulse parameters and on the filling gas density is analyzed. It is also shown that a substantial increase in the gain (for a given target and pulse energy) can be achieved by replacing the last step of the pulse with an exponential ramp.

  18. Ionization-induced dynamics of ultrashort laser pulses focused in a dense gas

    NASA Astrophysics Data System (ADS)

    Efimenko, E. S.; Kim, A. V.; Quiroga-Teixeiro, M.

    2009-10-01

    In the present paper we address several aspects of ionization-induced laser-gas interaction. First, we consider the ionization dynamics of an ultrashort laser pulse in the presence of additional electromagnetic perturbations, and show theoretically via dispersion relation analysis and numerically via 2D FDTD simulation that ionizationinduced scattering can occur even in the case of limited spatial and temporal scales and significantly affects pulse dynamics. Second, for the case of tight focusing of laser beam we show on the basis of numerical simulation that for 2D TE- and TM-polarized pulses there is a critical angle which delimits two qualitatively different regimes. For angles exceeding the critical one, the formed plasma distribution may become microstructured, otherwise the plasma structures are smooth. It is also shown than the critical angle and plasma-field dynamics depend significantly on pulse spectrum. Finally, we consider the impact of the electron collisions and Kerr nonlinearity and determine the boundaries within which the role of these effects is crucial.

  19. A multiphase model for pulsed ns-laser ablation of copper in an ambient gas

    SciTech Connect

    Autrique, D.; Chen, Z.; Alexiades, V.; Bogaerts, A.; Rethfeld, B.

    2012-07-30

    Laser ablation in an ambient gas is nowadays used in a growing number of applications, such as chemical analysis and pulsed laser deposition. Despite the many applications, the technique is still poorly understood. Therefore models describing the material evolution in time during short pulse laser irradiation can be helpful to unravel the puzzle and finally result in the optimization of the related applications. In the present work, a copper target is immersed in helium, initially set at atmospheric pressure and room temperature. Calculations are performed for a Gaussian-shaped laser pulse with a wavelength of 532 nm, full width at half maximum of 6 ns, and laser fluences up to 10 J/cm{sup 2}. In order to describe the transient behaviour in and above the copper target, hydrodynamic equations are solved. An internal energy method accounting for pressure relaxation is applied for the description of the target. In the plume domain a set of conservation equations is solved, assuming local thermodynamic equilibrium. Calculated crater depths and transmission profiles are compared with experimental results and similar trends are found. Our calculations indicate that for the laser fluence regime under study, explosive boiling could play a fundamental role in the plasma formation of metals under ns-pulsed laser irradiation.

  20. Nitrogen Gas Plasma Generated by a Static Induction Thyristor as a Pulsed Power Supply Inactivates Adenovirus

    PubMed Central

    Sakudo, Akikazu; Toyokawa, Yoichi; Imanishi, Yuichiro

    2016-01-01

    Adenovirus is one of the most important causative agents of iatrogenic infections derived from contaminated medical devices or finger contact. In this study, we investigated whether nitrogen gas plasma, generated by applying a short high-voltage pulse to nitrogen using a static induction thyristor power supply (1.5 kilo pulse per second), exhibited a virucidal effect against adenoviruses. Viral titer was reduced by one log within 0.94 min. Results from detection of viral capsid proteins, hexon and penton, by Western blotting and immunochromatography were unaffected by the plasma treatment. In contrast, analysis using the polymerase chain reaction suggested that plasma treatment damages the viral genomic DNA. Reactive chemical products (hydrogen peroxide, nitrate, and nitrite), ultraviolet light (UV-A) and slight temperature elevations were observed during the operation of the gas plasma device. Viral titer versus intensity of each potential virucidal factor were used to identify the primary mechanism of disinfection of adenovirus. Although exposure to equivalent levels of UV-A or heat treatment did not inactivate adenovirus, treatment with a relatively low concentration of hydrogen peroxide efficiently inactivated the virus. Our results suggest the nitrogen gas plasma generates reactive chemical products that inactivate adenovirus by damaging the viral genomic DNA. PMID:27322066

  1. Decomposition experiment of hydro-fluorocarbon gas by pulsed TEA CO2 laser

    NASA Astrophysics Data System (ADS)

    Maeno, Kazuo; Udagawa, Shinsuke; Toyada, Kazuhiro

    2005-03-01

    This paper deals with a trial experiment of decomposition of environmental gas R-12 by the pulsed TEA CO2 laser. Nowadays refrigerant R-12 and other hydro-chlorofluorocarbon gases are strongly prohibited to produce, as these gases have both strong ozone-depleting effects and green-house effects. The gases of already produced by huge amount should be decomposed as fast as possible by suitable technical methods. Along with the conventional kiln furnace of cement, arc discharge and the HG discharge are good methods for the freon decomposition. Both methods, however, have the weakness of electrode damages (arcing) or low-pressure operation (HF discharge). High power CO2 laser seems to have good properties for such decomposition with favorable wavelength for the absorption. In our small-scale experiment of gas decomposition a pulsed TEA CO2 laser of several joules is utilized to produce the plasma in R-12 flow channel of glass tube. The withdrawal of decomposed gases is performed by Ca alkalized water. The deposit mass is measured, and powder X-ray diffraction measurement is carried out on the deposit powder. The possibility of our laser gas decomposition is discussed.

  2. Effect of pulsed corona discharge voltage and feed gas flow rate on dissolved ozone concentration

    NASA Astrophysics Data System (ADS)

    Prasetyaningrum, A.; Ratnawati, Jos, B.

    2015-12-01

    Ozonization is one of the methods extensively used for water purification and degradation of organic materials. Ozone (O3) is recognized as a powerful oxidizing agent. Due to its strong oxidability and better environmental friendless, ozone increasing being used in domestic and industrial applications. Current technology in ozone production utilizes several techniques (corona discharge, ultra violet radiation and electrolysis). This experiment aimed to evaluating effect of voltage and gas flow rate on ozone production with corona discharge. The system consists of two net-type stainless steel electrode placed in a dielectric barrier. Three pulsed voltage (20, 30, 40 KV) and flow rate (5, 10, 15 L/min) were prepare for operation variable at high frequency (3.7 kHz) with AC pulsed power supply. The dissolved ozone concentration depends on the applied high-voltage level, gas flow rate and the discharge exposure duration. The ozone concentration increases with decreasing gas flow rate. Dissolved ozone concentrations greater than 200 ppm can be obtained with a minimum voltage 40 kV.

  3. Nitrogen Gas Plasma Generated by a Static Induction Thyristor as a Pulsed Power Supply Inactivates Adenovirus.

    PubMed

    Sakudo, Akikazu; Toyokawa, Yoichi; Imanishi, Yuichiro

    2016-01-01

    Adenovirus is one of the most important causative agents of iatrogenic infections derived from contaminated medical devices or finger contact. In this study, we investigated whether nitrogen gas plasma, generated by applying a short high-voltage pulse to nitrogen using a static induction thyristor power supply (1.5 kilo pulse per second), exhibited a virucidal effect against adenoviruses. Viral titer was reduced by one log within 0.94 min. Results from detection of viral capsid proteins, hexon and penton, by Western blotting and immunochromatography were unaffected by the plasma treatment. In contrast, analysis using the polymerase chain reaction suggested that plasma treatment damages the viral genomic DNA. Reactive chemical products (hydrogen peroxide, nitrate, and nitrite), ultraviolet light (UV-A) and slight temperature elevations were observed during the operation of the gas plasma device. Viral titer versus intensity of each potential virucidal factor were used to identify the primary mechanism of disinfection of adenovirus. Although exposure to equivalent levels of UV-A or heat treatment did not inactivate adenovirus, treatment with a relatively low concentration of hydrogen peroxide efficiently inactivated the virus. Our results suggest the nitrogen gas plasma generates reactive chemical products that inactivate adenovirus by damaging the viral genomic DNA. PMID:27322066

  4. Effect of pulsed corona discharge voltage and feed gas flow rate on dissolved ozone concentration

    SciTech Connect

    Prasetyaningrum, A. Ratnawati,; Jos, B.

    2015-12-29

    Ozonization is one of the methods extensively used for water purification and degradation of organic materials. Ozone (O{sub 3}) is recognized as a powerful oxidizing agent. Due to its strong oxidability and better environmental friendless, ozone increasing being used in domestic and industrial applications. Current technology in ozone production utilizes several techniques (corona discharge, ultra violet radiation and electrolysis). This experiment aimed to evaluating effect of voltage and gas flow rate on ozone production with corona discharge. The system consists of two net-type stainless steel electrode placed in a dielectric barrier. Three pulsed voltage (20, 30, 40 KV) and flow rate (5, 10, 15 L/min) were prepare for operation variable at high frequency (3.7 kHz) with AC pulsed power supply. The dissolved ozone concentration depends on the applied high-voltage level, gas flow rate and the discharge exposure duration. The ozone concentration increases with decreasing gas flow rate. Dissolved ozone concentrations greater than 200 ppm can be obtained with a minimum voltage 40 kV.

  5. Precise and high-speed control of partial pressures of multiple gas species in plasma process chamber using pulse-controlled gas injection

    SciTech Connect

    Morishita, Sadaharu; Goto, Tetsuya; Nagase, Masaaki; Ohmi, Tadahiro

    2009-05-15

    Multiprocesses in a single plasma process chamber with high throughput require precise, sequential, high-speed alteration of partial pressures of multiple gas species. A conventional gas-distribution system cannot realize this because the system seriously overshoots gas pressure immediately following valve operation. Furthermore, chamber volume and conductance of gas piping between the system and chamber should both be considered because they delay the stabilizing time of gas pressure. Therefore, the authors proposed a new gas-distribution system without overshoot by controlling gas flow rate based on pressure measurement, as well as a method of pulse-controlled gas injection immediately following valve operation. Time variation of measured partial pressure agrees well with a calculation based on an equivalent-circuit model that represents the chamber and gas piping between the system and chamber. Using pulse-controlled gas injection, the stabilizing time can be reduced drastically to 0.6 s for HBr added to pure Ar plasma, and 0.7 s for O{sub 2} added to Ar/HBr plasma; without the pulse control, the stabilizing times are 3 and 7 s, respectively. In the O{sub 2} addition case, rapid stabilization can be achieved during the period of line/space pattern etching of poly-Si on a thin SiO{sub 2} film. This occurs without anomalous etching of the underlying SiO{sub 2} film or the Si substrate near the sidewall, thus obtaining a wide process margin with high throughput.

  6. Picosecond pulsed laser deposition of metal-oxide sensing layers with controllable porosity for gas sensor applications

    NASA Astrophysics Data System (ADS)

    Kekkonen, Ville; Chaudhuri, Saumyadip; Clarke, Fergus; Kaisto, Juho; Liimatainen, Jari; Pandian, Santhosh Kumar; Piirto, Jarkko; Siltanen, Mikael; Zolotukhin, Aleksey

    2016-03-01

    Recent results of properties and performance of {WO}_3 gas sensing layers produced by industrial picosecond pulsed laser deposition process developed by Picodeon Ltd Oy are presented in this paper. {WO}_3 layers with controllable porosity and nanostructure were successfully deposited on commercial sensor platforms, and basic measurements to characterize their performance as gas sensors gave promising results.

  7. Pulsed microwave discharge in a capillary filled with atmospheric-pressure gas

    SciTech Connect

    Gritsinin, S. I.; Gushchin, P. A.; Davydov, A. M.; Ivanov, E. V.; Kossyi, I. A.

    2013-08-15

    A pulsed microwave coaxial capillary plasma source generating a thin plasma filament along the capillary axis in an atmospheric-pressure argon flow is described. The dynamics of filament formation is studied, and the parameters of the gas and plasma in the contraction region are determined. A physical model of discharge formation and propagation is proposed. The model is based on the assumption that, under the conditions in which the electric fields is substantially below the threshold value, the discharge operates in a specific form known as a self-sustained-non-self-sustained (SNS) microwave discharge.

  8. Oxidation of ammonium sulfite by a multi-needle-to-plate gas phase pulsed corona discharge reactor

    NASA Astrophysics Data System (ADS)

    Ren, Hua; Lu, Na; Shang, Kefeng; Li, Jie; Wu, Yan

    2013-03-01

    The oxidation of ammonium sulfite in the ammonia-based flue gas desulfurization (FGD) process was investigated in a multi-needle-to-plate gas phase pulsed corona discharge reactor in this paper. The effect of several parameters, including capacitance and peak pulse voltage of discharge system, electrode gap and bubbling gas flow rate on the oxidation rate of ammonium sulfite was reviewed. The oxidation rate of ammonium sulfite could reach 47.2% at the capacitance, the peak pulse voltage, electrode gap and bubbling gas flow rate equal to 2 nF, -24.6 k V, 35 mm and 4 L min-1 within treatment time of 40 min The experimental results indicate that the gas phase pulsed discharge system with a multi-needle-to-plate electrode can oxide the ammonium sulfite. The oxidation rate increased with the applied capacitance and peak pulse voltage and decreased with the electrode gap. As the bubbling gas flow rate increased, the oxidation rate increased first and then tended to reach a stationary value. These results would be important for the process optimization of the (NH4)2SO3 to (NH4)2SO4 oxidation.

  9. Self-injection and acceleration of electrons during ionization of gas atoms by a short laser pulse

    SciTech Connect

    Singh, K.P.

    2006-04-15

    Using a relativistic three-dimensional single-particle code, acceleration of electrons created during the ionization of nitrogen and oxygen gas atoms by a laser pulse has been studied. Barrier suppression ionization model has been used to calculate ionization time of the bound electrons. The energy gained by the electrons peaks for an optimum value of laser spot size. The electrons created near the tail do not gain sufficient energy for a long duration laser pulse. The electrons created at the tail of pulse escape before fully interacting with the trailing part of the pulse for a short duration laser pulse, which causes electrons to retain sufficient energy. If a suitable frequency chirp is introduced then energy of the electrons created at the tail of the pulse further increases.

  10. Piezoelectric characteristics of PZT thin films on polymer substrate

    NASA Astrophysics Data System (ADS)

    Kang, Min-Gyu; Do, Younh-Ho; Oh, Seung-Min; Rahayu, Rheza; Kim, Yiyein; Kang, Chong-Yun; Nahm, Sahn; Yoon, Seok-Jin

    2012-02-01

    The goal of piezoelectric energy harvesting is to improve the power efficiency of devices. One of the approaches for the improvement of power efficiency is to apply the large strain on the piezoelectric materials and then many scientists approached using thin films or nano-structured piezoelectric materials to obtain flexibility. However, the conventional thin film processes available for the fabrication of piezoelectric materials as PbZr0.52Ti0.48O3 (PZT) are not compatible with flexible electronics because they require high processing temperatures (>700^oC) to obtain piezoelectricity. Excimer laser annealing (ELA) is attractive heat process for the low-temperature crystallization, because of its material selectivity and short heating time. In this study, the amorphous PZT thin films were deposited on polymer substrate by rf-sputtering. To crystallize the amorphous films, the ELA was carried out with various conditions as function of the applied laser energy density, the number of pulse, and the repetition rate. To evaluate the piezoelectric characteristics, piezoelectric force microscopy (PFM) and electrometer are used. As a result, we obtained the crystallized PZT thin film on flexible substrate and obtained flexible piezoelectric energy harvester.

  11. Optical and application study of gas-liquid discharge excited by bipolar nanosecond pulse in atmospheric air

    NASA Astrophysics Data System (ADS)

    Wang, Sen; Wang, Wen-chun; Yang, De-zheng; Liu, Zhi-jie; Zhang, Shuai

    2014-10-01

    In this study, a bipolar nanosecond pulse with 20 ns rising time is employed to generate air gas-liquid diffuse discharge plasma with room gas temperature in quartz tube at atmospheric pressure. The image of the discharge and optical emission spectra of active species in the plasma are recorded. The plasma gas temperature is determined to be approximately 390 K by compared the experimental spectra with the simulated spectra, which is slightly higher than the room temperature. The result indicated that the gas temperature rises gradually with pulse peak voltage increasing, while decreases slightly with the electrode gap distance increasing. As an important application, bipolar nanosecond pulse discharge is used to sterilize the common microorganisms (Actinomycetes, Candida albicans and Escherichia coli) existing in drinking water, which performs high sterilization efficiency.

  12. Propagation of intense and short circularly polarized pulses in a molecular gas: From multiphoton ionization to nonlinear macroscopic effects

    NASA Astrophysics Data System (ADS)

    Lytova, M.; Lorin, E.; Bandrauk, A. D.

    2016-07-01

    We present a detailed analysis of the propagation dynamics of short and intense circularly polarized pulses in an aligned diatomic gas. Compared to linearly polarized intense pulses, high harmonic generation (HHG) and the coherent generation of attosecond pulses in the intense-circular-polarization case are a new research area. More specifically, we numerically study the propagation of intense and short circularly polarized pulses in the one-electron H2+ molecular gas, using a micro-macro Maxwell-Schrödinger model. In this model, the macroscopic polarization is computed from the solution of a large number of time-dependent Schrödinger equations, the source of dipole moments, and using a trace operator. We focus on the intensity and the phase of harmonics generated in the H2+ gas as a function of the pulse-propagation distance. We show that short coherent circularly polarized pulses of same helicity can be generated in the molecular gas as a result of cooperative phase-matching effects.

  13. Dynamics of pulsed expansion of polyatomic gas cloud: Internal-translational energy transfer contribution

    SciTech Connect

    Morozov, A. A.

    2007-08-15

    Polyatomic gas cloud expansion under pulsed laser evaporation is studied on the basis of one-dimensional direct Monte Carlo simulation. The effect of rotational-translational (RT) and vibrational-translational (VT) energy transfer on dynamics of the cloud expansion is considered. Efficiency of VT energy transfer dependence on the amount of evaporated matter is discussed. To analyze VT energy transfer impact, the number of collisions per molecule during the expansion is calculated. The data are generally in good agreement with available analytical and numerical predictions. Dependencies of the effective number of vibrational degrees of freedom on the number of vibrationally inelastic collisions are obtained and generalized. The importance of the consideration of energy transfer from the internal degrees of freedom to the translational ones is illustrated by an example of pulsed laser evaporation of polytetrafluoroethylene (PTFE). Based on the obtained regularities, analysis of experimental data on pulsed laser evaporation of aniline is performed. The calculated aniline vibrational temperature correlates well with the experimentally measured one.

  14. Design and characterization of piezoelectric ultrasonic motors

    NASA Astrophysics Data System (ADS)

    Yener, Serra

    one layer of ceramic and a brass teeth-like layer bonded on it. The displacement was amplified with the metal layer, the teeth of which were placed on the points of in-phase motion. The targeted application area is paper-feeding mechanism. In terms of application areas for the first design, a gas valve system and a micro vehicle were constructed. In addition, a new optical coherence tomography endoscope by utilizing the piezoelectric micromotor was designed. Finally, the prototype motor was integrated inside the camera of a cell phone to drive the zoom mechanism.

  15. Piezoelectric cantilever sensors

    NASA Technical Reports Server (NTRS)

    Shih, Wan Y. (Inventor); Shih, Wei-Heng (Inventor); Shen, Zuyan (Inventor)

    2008-01-01

    A piezoelectric cantilever with a non-piezoelectric, or piezoelectric tip useful as mass and viscosity sensors. The change in the cantilever mass can be accurately quantified by monitoring a resonance frequency shift of the cantilever. For bio-detection, antibodies or other specific receptors of target antigens may be immobilized on the cantilever surface, preferably on the non-piezoelectric tip. For chemical detection, high surface-area selective absorbent materials are coated on the cantilever tip. Binding of the target antigens or analytes to the cantilever surface increases the cantilever mass. Detection of target antigens or analytes is achieved by monitoring the cantilever's resonance frequency and determining the resonance frequency shift that is due to the mass of the adsorbed target antigens on the cantilever surface. The use of a piezoelectric unimorph cantilever allows both electrical actuation and electrical sensing. Incorporating a non-piezoelectric tip (14) enhances the sensitivity of the sensor. In addition, the piezoelectric cantilever can withstand damping in highly viscous liquids and can be used as a viscosity sensor in wide viscosity range.

  16. Gas-Monitor Detector for Intense and Pulsed VUV/EUV Free-Electron Laser Radiation

    NASA Astrophysics Data System (ADS)

    Sorokin, A. A.; Bobashev, S. V.; Feldhaus, J.; Gerth, Ch.; Gottwald, A.; Hahn, U.; Kroth, U.; Richter, M.; Shmaenok, L. A.; Steeg, B.; Tiedtke, K.; Treusch, R.

    2004-05-01

    In the framework of current developments of new powerful VUV and EUV radiation sources, like VUV free-electron-lasers or EUV plasma sources for 13-nm lithography, we developed a gas-monitor detector in order to measure the photon flux of highly intense and extremely pulsed VUV and EUV radiation in absolute terms. The device is based on atomic photoionization of a rare gas at low particle density. Therefore, it is free of degradation and almost transparent, which allows the detector to be used as a continuously working beam-intensity monitor. The extended dynamic range of the detector allowed its calibration with relative standard uncertainties of 4% in the Radiometry Laboratory of the Physikalisch-Technische Bundesanstalt at the electron-storage ring BESSY II in Berlin using spectrally dispersed synchrotron radiation at low photon intensities and its utilization for absolute photon flux measurements of high power sources. In the present contribution, we describe the design of the detector and its application for the characterization of VUV free-electron-laser radiation at the TESLA test facility in Hamburg. By first pulse resolved measurements, a peak power of more than 100 MW at a wavelength of 87 nm was detected.

  17. Adaptive piezoelectric sensoriactuator

    NASA Technical Reports Server (NTRS)

    Clark, Jr., Robert L. (Inventor); Vipperman, Jeffrey S. (Inventor); Cole, Daniel G. (Inventor)

    1996-01-01

    An adaptive algorithm implemented in digital or analog form is used in conjunction with a voltage controlled amplifier to compensate for the feedthrough capacitance of piezoelectric sensoriactuator. The mechanical response of the piezoelectric sensoriactuator is resolved from the electrical response by adaptively altering the gain imposed on the electrical circuit used for compensation. For wideband, stochastic input disturbances, the feedthrough capacitance of the sensoriactuator can be identified on-line, providing a means of implementing direct-rate-feedback control in analog hardware. The device is capable of on-line system health monitoring since a quasi-stable dynamic capacitance is indicative of sustained health of the piezoelectric element.

  18. Ionization effects in the generation of wake-fields by ultra-high contrast femtosecond laser pulses in argon gas

    SciTech Connect

    Makito, K.; Shin, J.-H.; Zhidkov, A.; Hosokai, T.; Masuda, S.; Kodama, R.

    2012-10-15

    Difference in mechanisms of wake-field generation and electron self-injection by high contrast femtosecond laser pulses in an initially neutral Argon gas and in pre-ionized plasma without ionization is studied via 2D particle-in-cell simulations including optical ionization of the media. For shorter laser pulses, 40 fs, ionization results only in an increase of the charge of accelerated electrons by factor of {approx}3 with qualitatively the same energy distribution. For longer pulses, 80 fs, a more stable wake field structure is observed in the neutral gas with the maximal energy of the accelerated electrons exceeding that in the fixed density plasma. In higher density Argon, an ionizing laser pulse converts itself to a complex system of solitons at a self-induced, critical density ramp.

  19. Propagation dynamics of femtosecond laser pulses in a hollow fiber filled with argon: constant gas pressure versus differential gas pressure

    NASA Astrophysics Data System (ADS)

    Nurhuda, Muhammad; Suda, Akira; Midorikawa, Katsumi; Hatayama, Masatoshi; Nagasaka, Keigo

    2003-09-01

    We investigate the dynamics of femtosecond laser pulses propagating in a hollow fiber filled with argon, through a full numerical solution of the nonlinear Schrödinger equation. The simulation results show that, if the intensity is low and no ionization takes place, the spatial profile of the beam does not change very much so that its propagation model may be simplified to a one-dimensional model. If the intensity is high and ionization takes place, the spatial dynamics as well as temporal dynamics become very complicated because of self-focusing and defocusing. It is found that, for the same value of the B integral, self-focusing inside a hollow fiber can be substantially suspended by a differential gas pressure technique, where the gas pressure is set to be a minimum at the entrance and then increased with the propagation distance. Numerical simulations show that using such a technique, the energy transmitted during propagation inside hollow fiber is significantly enhanced, and the spatial phase is also improved.

  20. Energy collection via Piezoelectricity

    NASA Astrophysics Data System (ADS)

    Naveen Kumar, Ch

    2015-12-01

    In the present days, wireless data transmission techniques are commonly used in electronic devices. For powering them connection needs to be made to the power supply through wires else power may be supplied from batteries. Batteries require charging, replacement and other maintenance efforts. So, some alternative methods need to be developed to keep the batteries full time charged and to avoid the need of any consumable external energy source to charge the batteries. Mechanical energy harvesting utilizes piezoelectric components where deformations produced by different means are directly converted to electrical charge via piezoelectric effect. The proposed work in this research recommends Piezoelectricity as a alternate energy source. The motive is to obtain a pollution-free energy source and to utilize and optimize the energy being wasted. Current work also illustrates the working principle of piezoelectric crystal and various sources of vibration for the crystal.

  1. Piezoelectric Pb(Zrx, Ti1-x)O3 thin film cantilever and bridge acoustic sensors for miniaturized photoacoustic gas detectors

    NASA Astrophysics Data System (ADS)

    Ledermann, Nicolas; Muralt, Paul; Baborowski, Jacek; Forster, Martin; Pellaux, Jean-Paul

    2004-12-01

    Novel, highly sensitive piezoelectric acoustic sensors based on partially unclamped Pb(Zrx, Ti1-x)O3 (PZT) coated cantilever and bridge have been fabricated by silicon micromachining. High sensitivity at low frequencies (5-100 Hz) has been achieved by patterning very narrow slits (3 to 5 µm) around the structures. A typical response of 100 mV Pa-1 and a noise equivalent pressure of 1.6 mPa Hz1/2 at 20 Hz have been measured using a 10 pF charge amplifier. Stress compensation, dry etching and integration of high performance piezoelectric thin films were the key issues. PZT/Pt/SiO2 stacks have been patterned by reactive ion etching and stress compensation has been achieved by compensating the PZT film's tensile stress by adjusting the thickness of a thermal SiO2 layer. The integration of sol-gel PZT films with a transverse piezoelectric coefficient e31,f of -12.8 C m-2 has been realized without any degradation of the properties. The microphones were successfully integrated into a miniature photoacoustic detector and tested for CO2 detection. Concentrations down to 330 ppm could be measured with significant signals.

  2. Piezoelectrically Enhanced Photocathodes

    NASA Technical Reports Server (NTRS)

    Beach, Robert A.; Nikzad, Shouleh; Bell, Lloyd Douglas; Strittmatter, Robert

    2011-01-01

    Doping of photocathodes with materials that have large piezoelectric coefficients has been proposed as an alternative means of increasing the desired photoemission of electrons. Treating cathode materials to increase emission of electrons is called "activation" in the art. It has been common practice to activate photocathodes by depositing thin layers of suitable metals (usually, cesium). Because cesium is unstable in air, fabrication of cesiated photocathodes and devices that contain them must be performed in sealed tubes under vacuum. It is difficult and costly to perform fabrication processes in enclosed, evacuated spaces. The proposed piezoelectrically enhanced photocathodes would have electron-emission properties similar to those of cesiated photocathodes but would be stable in air, and therefore could be fabricated more easily and at lower cost. Candidate photocathodes include nitrides of elements in column III of the periodic table . especially compounds of the general formula Al(x)Ga(1.x)N (where 0< or = x < or =.1). These compounds have high piezoelectric coefficients and are suitable for obtaining response to ultraviolet light. Fabrication of a photocathode according to the proposal would include inducement of strain in cathode layers during growth of the layers on a substrate. The strain would be induced by exploiting structural mismatches among the various constituent materials of the cathode. Because of the piezoelectric effect in this material, the strain would give rise to strong electric fields that, in turn, would give rise to a high concentration of charge near the surface. Examples of devices in which piezoelectrically enhanced photocathodes could be used include microchannel plates, electron- bombarded charge-coupled devices, image tubes, and night-vision goggles. Piezoelectrically enhanced photocathode materials could also be used in making highly efficient monolithic photodetectors. Highly efficient and stable piezoelectrically enhanced

  3. Piezoelectric Energy Harvesting Solutions

    PubMed Central

    Caliò, Renato; Rongala, Udaya Bhaskar; Camboni, Domenico; Milazzo, Mario; Stefanini, Cesare; de Petris, Gianluca; Oddo, Calogero Maria

    2014-01-01

    This paper reviews the state of the art in piezoelectric energy harvesting. It presents the basics of piezoelectricity and discusses materials choice. The work places emphasis on material operating modes and device configurations, from resonant to non-resonant devices and also to rotational solutions. The reviewed literature is compared based on power density and bandwidth. Lastly, the question of power conversion is addressed by reviewing various circuit solutions. PMID:24618725

  4. Laminated piezoelectric transformer

    NASA Technical Reports Server (NTRS)

    Vazquez Carazo, Alfredo (Inventor)

    2006-01-01

    A laminated piezoelectric transformer is provided using the longitudinal vibration modes for step-up voltage conversion applications. The input portions are polarized to deform in a longitudinal plane and are bonded to an output portion. The deformation of the input portions is mechanically coupled to the output portion, which deforms in the same longitudinal direction relative to the input portion. The output portion is polarized in the thickness direction relative its electrodes, and piezoelectrically generates a stepped-up output voltage.

  5. Direct adaptive fuzzy control of a translating piezoelectric flexible manipulator driven by a pneumatic rodless cylinder

    NASA Astrophysics Data System (ADS)

    Qiu, Zhi-cheng; Wang, Bin; Zhang, Xian-min; Han, Jian-da

    2013-04-01

    This study presents a novel translating piezoelectric flexible manipulator driven by a rodless cylinder. Simultaneous positioning control and vibration suppression of the flexible manipulator is accomplished by using a hybrid driving scheme composed of the pneumatic cylinder and a piezoelectric actuator. Pulse code modulation (PCM) method is utilized for the cylinder. First, the system dynamics model is derived, and its standard multiple input multiple output (MIMO) state-space representation is provided. Second, a composite proportional derivative (PD) control algorithms and a direct adaptive fuzzy control method are designed for the MIMO system. Also, a time delay compensation algorithm, bandstop and low-pass filters are utilized, under consideration of the control hysteresis and the caused high-frequency modal vibration due to the long stroke of the cylinder, gas compression and nonlinear factors of the pneumatic system. The convergence of the closed loop system is analyzed. Finally, experimental apparatus is constructed and experiments are conducted. The effectiveness of the designed controllers and the hybrid driving scheme is verified through simulation and experimental comparison studies. The numerical simulation and experimental results demonstrate that the proposed system scheme of employing the pneumatic drive and piezoelectric actuator can suppress the vibration and achieve the desired positioning location simultaneously. Furthermore, the adopted adaptive fuzzy control algorithms can significantly enhance the control performance.

  6. The Influence of Extreme Water Pulses on Greenhouse Gas Emissions from Soils

    NASA Astrophysics Data System (ADS)

    Petrakis, S.; Vargas, R.; Seyfferth, A.; Kan, J.; Inamdar, S. P.

    2015-12-01

    Anthropogenic activity increasing the amount of radiatively active gases, or Greenhouse Gases (GHGs) in the earth's atmosphere has led to shifts in weather patterns. Climate models predict the occurrence of large storms may increase in frequency and intensity in the mid-Atlantic region. Knowing that extreme precipitation events are rare, testing the influence of large water pulses across different soil types within an ecosystem is challenging. Large additions of water could promote or inhibit microbial activity, and change soil chemistry within a few days. Rapid changes in soil moisture lead to shifts in the behavior of soils as either sinks or sources of several GHGs (i.e., CO2, CH4 and N2O). Unfortunately, it is still unclear how rewetting events could impact the magnitude of GHG fluxes and how changing soil chemical parameters influence these responses. An experiment was designed to test the influence of extreme repeated water pulses on GHG fluxes from four different soils, representing key topographic locations within a watershed in the Piedmont region (i.e., forested upland, forested lowland, creek, wetland). Intact soil cores from these four soil types were kept under constant temperature (22oC) and we measured their responses to extreme water pulses. We continuously (hourly resolution) measured CO2, CH4 and N2O fluxes using a LI-8100A (Licor, Lincoln, NE) multiplexed system coupled to a Picarro G2508 (Picarro, Santa Clara, CA). Furthermore, we used a rhizolysimeter for porewater extraction to measure pH, redox, and water chemistry throughout the experiment. We hypothesized that repeated extreme water pulses would result in non-linear responses of GHG flux magnitudes and dynamics, and these dynamics would relate to changes in soil chemistry. We found that soil moisture alone could not explain the dynamics of GHG fluxes, but these extreme water pulses influenced the overall temporal patterns of all GHGs across all soil types. We also examined the 100 year

  7. Performance Evaluation of Hybrid Gas Turbine Engine Embedded with Pulse Detonation Combustor

    NASA Astrophysics Data System (ADS)

    Deng, Jun-Xiang; Yan, Chuan-Jun; Zheng, Long-Xi; Huang, Xi-Qiao

    2011-09-01

    The numerical investigations of performance evaluation of a hybrid gas turbine engine embedded with a pulse detonation combustor (PDC) were performed to examine the improvement of the performance of the hybrid propulsion system. The calculation model and method were described. The architecture, configuration and size of detonation tubes were investigated in the calculation. Two models of detonation tube exit temperature were utilized. Eight configuration choices for the PDC based on the calculation model were designed. Specific fuel consumption of a hybrid gas turbine engine was compared with that of the baseline engine at the condition of the same engine net thrust. The experimental research of a PDC interacted with a radial flow turbine of a turbocharger was conducted. The numerical results show that if the net thrust of hybrid PDC engine is matched to that of baseline engine, specific fuel consumption of hybrid PDC engine is 20-25% less than that of baseline engine. The total volume of the hybrid engine combustor is reduced. The incorporation of PDC into gas turbine engine can improve the performance of hybrid PDC engine, decrease the combustor weight, and increase the thrust-weight ratio. The experimental results show that the fully developed detonation waves are achieved in the experimental apparatus.

  8. Creation of Pure Frozen Gas Targets for Ion Acceleration using Short Pulse Lasers

    NASA Astrophysics Data System (ADS)

    McCary, Edward; Stehr, Florian; Jiao, Xuejing; Quevedo, Hernan; Franke, Philip; Agustsson, Ronald; Oshea, Finn; Berry, Robert; Chao, Dennis; Woods, Kayley; Gautier, Donald; Letzring, Sam; Hegelich, Bjorn

    2015-11-01

    A system for shooting interchangeable frozen gas targets was developed at the University of Texas and will be tested at Los Alamos National Lab. A target holder which can hold up to five substrates used for target growing was cryogenically cooled to temperatures below 14 K. The target substrates consist of holes with diameters ranging from 15 μm-500 μm and TEM grids with micron scale spacing, across which films of ice are frozen by releasing small amounts of pure gas molecules directly into the vacuum target chamber. Frozen gas targets comprised of simple molecules like methane and single element gasses like hydrogen and deuterium will provide novel target configuations that will be compared with laser plasma interaction simulations. The targets will be shot with the ultra-intense short-pulse Trident laser. Accelerated ion spectra will be characterized using a Thomson Parabola with magnetic field strength of 0.92T and electric field strength of 30kV. Hydrogen targets will be additionally characterized using stacks of copper which become activated upon exposure to energetic protons resulting in a beta decay signal which be imaged on electron sensitive imaging plates to provide an energy spectrum and spacial profile of the proton beam. Details of target creation and pre-shot characterization will be presented.

  9. Stretchable piezoelectric nanocomposite generator

    NASA Astrophysics Data System (ADS)

    Park, Kwi-Il; Jeong, Chang Kyu; Kim, Na Kyung; Lee, Keon Jae

    2016-06-01

    Piezoelectric energy conversion that generate electric energy from ambient mechanical and vibrational movements is promising energy harvesting technology because it can use more accessible energy resources than other renewable natural energy. In particular, flexible and stretchable piezoelectric energy harvesters which can harvest the tiny biomechanical motions inside human body into electricity properly facilitate not only the self-powered energy system for flexible and wearable electronics but also sensitive piezoelectric sensors for motion detectors and in vivo diagnosis kits. Since the piezoelectric ZnO nanowires (NWs)-based energy harvesters (nanogenerators) were proposed in 2006, many researchers have attempted the nanogenerator by using the various fabrication process such as nanowire growth, electrospinning, and transfer techniques with piezoelectric materials including polyvinylidene fluoride (PVDF) polymer and perovskite ceramics. In 2012, the composite-based nanogenerators were developed using simple, low-cost, and scalable methods to overcome the significant issues with previously-reported energy harvester, such as insufficient output performance and size limitation. This review paper provides a brief overview of flexible and stretchable piezoelectric nanocomposite generator for realizing the self-powered energy system with development history, power performance, and applications.

  10. Piezoelectric Pins for Use as Dust Detectors

    NASA Astrophysics Data System (ADS)

    Manning, H. L. K.; Campbell, I. H.; Nelson, K. A.; Yager, J. R.

    2002-09-01

    Piezoelectric pins are devices currently used in a number of applications including detecting elementary particle beams, monitoring volcanoes, and detecting high-speed micro-sized particles. These pins provide a means of studying ejecta from cratering processes in the laboratory and offer a potential lightweight, low power, flight dust detector. Using the hypervelocity dust particle accelerator at Concordia College in Moorhead, Minnesota, we have investigated the transient charge generated by piezoelectric pins impacted by dust particles. Carbonyl iron dust particles of 0.5-5 micrometer diameter having speeds ranging from 1-5 km/sec impacted the pins. The DC-100 MHz pin response was recorded and analyzed. The transient pin response to a single particle consists of many charge pulses of alternating sign (less than 10 ns in duration) separated by the pressure wave propagation time across the crystal (typically 100 ns). The charge produced by the pin changes sign when the pressure waves in the piezoelectric crystal reflect off of the metal electrodes. The magnitude of the pin response as a function of the impacting particle properties is presented and discussed. Pins using both polycrystalline PZT and single crystal LiNbO3 as the piezoelectric material were studied. This work is supported at Concordia College by the Minnesota Space Grant Consortium.

  11. Elimination of the light shift in rubidium gas cell frequency standards using pulsed optical pumping

    NASA Technical Reports Server (NTRS)

    English, T. C.; Jechart, E.; Kwon, T. M.

    1978-01-01

    Changes in the intensity of the light source in an optically pumped, rubidium, gas cell frequency standard can produce corresponding frequency shifts, with possible adverse effects on the long-term frequency stability. A pulsed optical pumping apparatus was constructed with the intent of investigating the frequency stability in the absence of light shifts. Contrary to original expectations, a small residual frequency shift due to changes in light intensity was experimentally observed. Evidence is given which indicates that this is not a true light-shift effect. Preliminary measurements of the frequency stability of this apparatus, with this small residual pseudo light shift present, are presented. It is shown that this pseudo light shift can be eliminated by using a more homogeneous C-field. This is consistent with the idea that the pseudo light shift is due to inhomogeneity in the physics package (position-shift effect).

  12. Pulse-modulated dual-gas control subsystem for space cabin atmosphere

    NASA Technical Reports Server (NTRS)

    Jackson, J. K.

    1974-01-01

    An atmosphere control subsystem (ACS) was developed for use in a closed manned cabin, such as the Space Shuttle Orbiter. This subsystem uses the Perkin Elmer mass spectrometer for continuous measurement of major atmospheric constituents (H2, H2O, N2, O2, and CO2). The O2 and N2 analog signals are used as inputs to the controller, which produces a pulse-frequency-modulated output to operate the N2 gas admission solenoid valve and an on-off signal to operate the O2 valve. The proportional controller characteristic results in improved control accuracy as compared with previously used on-off controllers having significant dead-band. A 60-day evaluation test was performed on the ACS during which operation was measured at various values of control setpoint and simulated cabin leakage.

  13. Formation of Brittle Phases During Pulsed Current Gas Tungsten Arc Welding of Titanium to Aluminum Alloys

    NASA Astrophysics Data System (ADS)

    Wei, Shouzheng; Li, Yajiang; Wang, Juan; Liu, Kun

    2014-04-01

    Welding of titanium alloy TA15 to aluminum alloy Al 2024 was conducted by pulsed current gas tungsten arc welding using AlSi12 filler metal. Formation process of phases near the Ti/Al interface was discussed. Titanium and aluminum were partially fusion welded in the upper part while brazed together in the middle and bottom parts of the joint. In the upper part of the joint, intermetallics Ti3Al + Ti5Si3, TiAl + Ti5Si3, and TiAl3 were formed as three layers orderly from the titanium side to the weld metal. In the middle and bottom parts of the joint, intermetallics Ti5Si3 and TiAl3 were formed as two layers near the Ti/Al interface.

  14. Terahertz generation by nonlinear mixing of laser pulses in a clustered gas

    SciTech Connect

    Kumar, Manoj; Tripathi, V. K.

    2011-05-15

    A scheme of terahertz (THz) generation by two collinear laser pulses of finite spot size in a clustered gas is investigated theoretically. The lasers quickly ionize the atoms of the clusters, converting them into plasma balls, and exert a ponderomotive force on the cluster electrons, producing a beat frequency longitudinal current of limited transverse extent. The current acts as an antenna to produce beat frequency terahertz radiation. As the cluster expands under the hydrodynamic pressure, plasma frequency of cluster electrons {omega}{sub pe} decreases and approaches {radical}(3) times the frequency of laser, resonant heating and expansion of clusters occurs. On further expansion of clusters as {omega}{sub pe} approaches {radical}(3) times the terahertz frequency, resonant enhancement in THz radiated power occurs.

  15. Operability of an Ejector Enhanced Pulse Combustor in a Gas Turbine Environment

    NASA Technical Reports Server (NTRS)

    Paxson, Daniel E.; Dougherty, Kevin

    2008-01-01

    A pressure-gain combustor comprised of a mechanically valved, liquid fueled pulsejet, an ejector, and an enclosing shroud, was coupled to a small automotive turbocharger to form a self-aspirating, thrust producing gas turbine engine. The system was constructed in order to investigate issues associated with the interaction of pulsed combustion devices and turbomachinery. Installed instrumentation allowed for sensing of distributed low frequency pressure and temperature, high frequency pressure in the shroud, fuel flow rate, rotational speed, thrust, and laboratory noise. The engine ran successfully and reliably, achieving a sustained thrust of 5 to 6 lbf, and maintaining a rotor speed of approximately 90,000 rpm, with a combustor pressure gain of approximately 4 percent. Numerical simulations of the system without pressure-gain combustion indicated that the turbocharger would not operate. Thus, the new combustor represented a substantial improvement in system performance. Acoustic measurements in the shroud and laboratory indicated turbine stage sound pressure level attenuation of 20 dB. This is consistent with published results from detonative combustion experiments. As expected, the mechanical reed valves suffered considerable damage under the higher pressure and thermal loading characteristics of this system. This result underscores the need for development of more robust valve systems for this application. The efficiency of the turbomachinery components did not appear to be significantly affected by unsteadiness associated with pulsed combustion, though the steady component efficiencies were already low, and thus not expected to be particularly sensitive.

  16. Effect of gas heating on the generation of an ultrashort avalanche electron beam in the pulse-periodic regime

    NASA Astrophysics Data System (ADS)

    Baksht, E. Kh.; Burachenko, A. G.; Lomaev, M. I.; Sorokin, D. A.; Tarasenko, V. F.

    2015-07-01

    The generation of an ultrashort avalanche electron beam (UAEB) in nitrogen in the pulse-periodic regime is investigated. The gas temperature in the discharge gap of the atmospheric-pressure nitrogen is measured from the intensity distribution of unresolved rotational transitions ( C 3Π u , v' = 0) → ( B 3Π g , v″ = 0) in the nitrogen molecule for an excitation pulse repetition rate of 2 kHz. It is shown that an increase in the UAEB current amplitude in the pulse-periodic regime is due to gas heating by a series of previous pulses, which leads to an increase in the reduced electric field strength as a result of a decrease in the gas density in the zone of the discharge formation. It is found that in the pulse-periodic regime and the formation of the diffuse discharge, the number of electrons in the beam increases by several times for a nitrogen pressure of 9 × 103 Pa. The dependences of the number of electrons in the UAEB on the time of operation of the generator are considered.

  17. Picosecond pulses compression at 1053-nm center wavelength by using a gas-filled hollow-core fiber compressor

    NASA Astrophysics Data System (ADS)

    Huang, Zhi-Yuan; Wang, Ding; Leng, Yu-Xin; Dai, Ye

    2015-01-01

    We theoretically study the nonlinear compression of picosecond pulses with 10-mJ of input energy at the 1053-nm center wavelength by using a one-meter-long gas-filled hollow-core fiber (HCF) compressor and considering the third-order dispersion (TOD) effect. It is found that when the input pulse is about 1 ps/10 mJ, it can be compressed down to less than 20 fs with a high transmission efficiency. The gas for optimal compression is krypton gas which is filled in a HCF with a 400-μm inner diameter. When the input pulse duration is increased to 5 ps, it can also be compressed down to less than 100 fs efficiently under proper conditions. The results show that the TOD effect has little impact on picosecond pulse compression and the HCF compressor can be applied on compressing picosecond pulses efficiently with a high compression ratio, which will benefit the research of high-field laser physics. Project supported by the National Natural Science Foundation of China (Grant Nos. 11204328, 61221064, 61078037, 11127901, and 11134010), the National Basic Research Program of China (Grant No. 2011CB808101), the Commission of Science and Technology of Shanghai, China (Grant No. 12dz1100700), the Natural Science Foundation of Shanghai, China (Grant No. 13ZR1414800), and the International Science and Technology Cooperation Program of China (Grant No. 2011DFA11300).

  18. Development of a pulsed uniform supersonic gas expansion system based on an aerodynamic chopper for gas phase reaction kinetic studies at ultra-low temperatures

    NASA Astrophysics Data System (ADS)

    Jiménez, E.; Ballesteros, B.; Canosa, A.; Townsend, T. M.; Maigler, F. J.; Napal, V.; Rowe, B. R.; Albaladejo, J.

    2015-04-01

    A detailed description of a new pulsed supersonic uniform gas expansion system is presented together with the experimental validation of the setup by applying the CRESU (French acronym for Cinétique de Réaction en Ecoulement Supersonique Uniforme or Reaction Kinetics in a Uniform Supersonic Flow) technique to the gas-phase reaction of OH radicals with 1-butene at ca. 23 K and 0.63 millibars of helium (carrier gas). The carrier gas flow, containing negligible mixing ratios of OH-precursor and 1-butene, is expanded from a high pressure reservoir (337 millibars) to a low pressure region (0.63 millibars) through a convergent-divergent nozzle (Laval type). The novelty of this experimental setup is that the uniform supersonic flow is pulsed by means of a Teflon-coated aerodynamic chopper provided with two symmetrical apertures. Under these operational conditions, the designed Laval nozzle achieves a temperature of (22.4 ± 1.4) K in the gas jet. The spatial characterization of the temperature and the total gas density within the pulsed uniform supersonic flow has also been performed by both aerodynamical and spectroscopic methods. The gas consumption with this technique is considerably reduced with respect to a continuous CRESU system. The kinetics of the OH+1-butene reaction was investigated by the pulsed laser photolysis/laser induced fluorescence technique. The rotation speed of the disk is temporally synchronized with the exit of the photolysis and the probe lasers. The rate coefficient (kOH) for the reaction under investigation was then obtained and compared with the only available data at this temperature.

  19. Development of a pulsed uniform supersonic gas expansion system based on an aerodynamic chopper for gas phase reaction kinetic studies at ultra-low temperatures.

    PubMed

    Jiménez, E; Ballesteros, B; Canosa, A; Townsend, T M; Maigler, F J; Napal, V; Rowe, B R; Albaladejo, J

    2015-04-01

    A detailed description of a new pulsed supersonic uniform gas expansion system is presented together with the experimental validation of the setup by applying the CRESU (French acronym for Cinétique de Réaction en Ecoulement Supersonique Uniforme or Reaction Kinetics in a Uniform Supersonic Flow) technique to the gas-phase reaction of OH radicals with 1-butene at ca. 23 K and 0.63 millibars of helium (carrier gas). The carrier gas flow, containing negligible mixing ratios of OH-precursor and 1-butene, is expanded from a high pressure reservoir (337 millibars) to a low pressure region (0.63 millibars) through a convergent-divergent nozzle (Laval type). The novelty of this experimental setup is that the uniform supersonic flow is pulsed by means of a Teflon-coated aerodynamic chopper provided with two symmetrical apertures. Under these operational conditions, the designed Laval nozzle achieves a temperature of (22.4 ± 1.4) K in the gas jet. The spatial characterization of the temperature and the total gas density within the pulsed uniform supersonic flow has also been performed by both aerodynamical and spectroscopic methods. The gas consumption with this technique is considerably reduced with respect to a continuous CRESU system. The kinetics of the OH+1-butene reaction was investigated by the pulsed laser photolysis/laser induced fluorescence technique. The rotation speed of the disk is temporally synchronized with the exit of the photolysis and the probe lasers. The rate coefficient (k(OH)) for the reaction under investigation was then obtained and compared with the only available data at this temperature. PMID:25933898

  20. Surface Treatment of Polymer Film by Atmospheric Pulsed Microplasma: Study on Gas Humidity Effect for Improving the Hydrophilic Property

    NASA Astrophysics Data System (ADS)

    Shimizu, Kazuo; Umeda, Akira; Blajan, Marius

    2011-08-01

    Surface treatment of a poly(ethylene naphthalate) (PEN) film by atmospheric pulsed microplasma with humid Ar gas was experimentally investigated. A Marx generator with metal-oxide-semiconductor field-effect transistor (MOSFET) switches that generates negative pulses was used for generating microplasma. Hydrophilization was estimated by measuring contact angle before and after the microplasma surface treatment by a remote process. The initial contact angle was about 76°. The minimum contact angle of about 20° was obtained after a treatment, a discharge voltage of -1.3 kV negative pulse, a frequency of 24 kHz, a gas relative humidity of about 60%. Analysis by X-ray photoelectron spectroscopy (XPS) showed a decrease in the C 1s peak corresponding to the C-H bond or C-C bond, and increases in the O 1s peaks corresponding to the C=O bond or O-H bond.

  1. Piezoelectric Ceramics and Their Applications

    ERIC Educational Resources Information Center

    Flinn, I.

    1975-01-01

    Describes the piezoelectric effect in ceramics and presents a quantitative representation of this effect. Explains the processes involved in the manufacture of piezoelectric ceramics, the materials used, and the situations in which they are applied. (GS)

  2. Characterization of cluster/monomer ratio in pulsed supersonic gas jets

    NASA Astrophysics Data System (ADS)

    Gao, Xiaohui; Shim, Bonggu; Wang, Xiaoming; Downer, Mike

    2008-11-01

    While Rayleigh scatter and interferometry are standard methods for determining average cluster size and total atomic density, respectively, in cluster gas jets, determination of cluster mass fraction has required additional input from gasdynamic simulations. Here we determine cluster mass fraction experimentally with fs-time-resolved measurement of refractive index using frequency domain interferometery (FDI) after ionization and heating by a pump pulse. The essence of this method is that the negative index contribution of monomer plasma appears immediately after ionization by the pump, whereas the positive contribution of clustered plasma becomes significant only after clusters expand to a Mie resonance condition, enabling separation of monomer and cluster densities in the time domain. This method allows us to investigate various influences (nozzle geometry, temperature, etc.) on cluster fraction, which varies widely in nominally identical gas jets, and is a critical parameter in realizing phase-matched harmonic generation at high laser intensity, which would lead to an efficient table-top soft X-ray source.

  3. Two techniques for temporal pulse compression in gas-filled hollow-core kagomé photonic crystal fiber.

    PubMed

    Mak, K F; Travers, J C; Joly, N Y; Abdolvand, A; Russell, P St J

    2013-09-15

    We demonstrate temporal pulse compression in gas-filled kagomé hollow-core photonic crystal fiber (PCF) using two different approaches: fiber-mirror compression based on self-phase modulation under normal dispersion, and soliton effect self-compression under anomalous dispersion with a decreasing pressure gradient. In the first, efficient compression to near-transform-limited pulses from 103 to 10.6 fs was achieved at output energies of 10.3 μJ. In the second, compression from 24 to 6.8 fs was achieved at output energies of 6.6 μJ, also with near-transform-limited pulse shapes. The results illustrate the potential of kagomé-PCF for postprocessing the output of fiber lasers. We also show that, using a negative pressure gradient, ultrashort pulses can be delivered directly into vacuum. PMID:24104822

  4. High Temperature Piezoelectric Drill

    NASA Technical Reports Server (NTRS)

    Bao, Xiaoqi; Scott, James; Boudreau, Kate; Bar-Cohen, Yoseph; Sherrit, Stewart; Badescu, Mircea; Shrout, Tom; Zhang, Shujun

    2009-01-01

    The current NASA Decadal mission planning effort has identified Venus as a significant scientific target for a surface in-situ sampling/analyzing mission. The Venus environment represents several extremes including high temperature (460 deg C), high pressure (9 MPa), and potentially corrosive (condensed sulfuric acid droplets that adhere to surfaces during entry) environments. This technology challenge requires new rock sampling tools for these extreme conditions. Piezoelectric materials can potentially operate over a wide temperature range. Single crystals, like LiNbO3, have a Curie temperature that is higher than 1000 deg C and the piezoelectric ceramics Bismuth Titanate higher than 600 deg C. A study of the feasibility of producing piezoelectric drills that can operate in the temperature range up to 500 deg C was conducted. The study includes the high temperature properties investigations of engineering materials and piezoelectric ceramics with different formulas and doping. The drilling performances of a prototype Ultrasonic/Sonic Drill/Corer (USDC) using high temperate piezoelectric ceramics and single crystal were tested at temperature up to 500 deg C. The detailed results of our study and a discussion of the future work on performance improvements are presented in this paper.

  5. Effect of Oxygen Gas on the Decomposition of Dye by Pulsed Discharge in Water Droplet Spray

    NASA Astrophysics Data System (ADS)

    Nose, Taisuke; Yokoyama, Yuzo; Nakamura, Akira; Minamitani, Yasushi

    Effect of O2 on the decolorization of indigo carmine and on the production of dissolved species such as NO2-, NO3-, O3 and H2O2 in the treatment water by pulsed discharge in water droplet spray was investigated by controlling the O2/N2 ratios as carrier gases in the reactor. The decolorization rate gradually increased with rise in O2 ratio, which reached a constant value in the range of 50% to 90% O2 ratio and decreased in pure O2. The maximum value was about 2 times as high as that of 20% O2 ratio. The decolorization efficiency was not affected by gas flow rate in the range of 4 L/min to 50 L/min. NO2- in the treatment water was only detected in pure N2, but NO3- was produced in O2/N2. NO2- added to the treatment water was not oxidized in pure N2, but was perfectly converted to NO3- in O2/N2. These results implied that hydroxyl radical produced in gas phase does not directly contribute to the oxidation of substances in water. O3 concentration gradually increased with rise in O2 ratio, whereas H2O2 concentration decreased. In the range of 50 to 80% O2 ratio, O3 and H2O2 concentrations were approximately constant value, similar to the trend of decolorization rate. Moreover rate constants on various gas mixing ratio of O2/N2 were determined from the kinetics study. These results suggested that hydroxyl radical produced in the treatment water by the chain reactions of O3 and hydroperoxy radical (HO2·) plays an important role of the decomposition of molecules in water.

  6. Active Piezoelectric Diaphragms

    NASA Technical Reports Server (NTRS)

    Bryant, Robert G.; Effinger, Robert T., IV; Aranda, Isaiah, Jr.; Copeland, Ben M.; Covington, Ed W., III

    2002-01-01

    Several active piezoelectric diaphragms were fabricated by placing unelectroded piezoelectric disks between copper clad films patterned with Inter-Circulating Electrodes "ICE". When a voltage potential is applied to the electrodes, the result is radially distributed electric field that mechanically strains the piezo-ceramic along the Z-axis (perpendicular to the applied electric field), rather than the expected in-plane (XY-axis) direction. Unlike other out of plane piezoelectric actuators, which are benders, these Radial Field Diaphragms (RFDs) strain concentrically yet afford high displacements while maintaining a constant circumference. This paper covers the fabrication and characterization of these diaphragms as a function of poling field strength, ceramic diameter and line spacing, as well as the surface topography, the resulting strain field and displacement as a function of applied voltage ranging from DC to 10 Hz.

  7. Piezoelectric Motors and Transformers

    NASA Astrophysics Data System (ADS)

    Uchino, K.

    Piezoelectric ceramics forms a new field between electronic and structural ceramics [1-4]. Application fields are classified into three categories: positioners, motors, and vibration suppressors. From the market research result for 80 Japanese component industries in 1992, tiny motors in the range of 5-8 mm are required in large numbers for office and portable equipment; the conventional electromagnetic (EM) motors are rather difficult to produce in this size with sufficient energy efficiency, while Silicon MEMS actuators are too small to be used in practice. Piezoelectric ultrasonic motors whose efficiency is insensitive to size are superior in the millimeter motor area. The manufacturing precision of optical instruments such as lasers and cameras, and the positioning accuracy for fabricating semiconductor chips are of the order of 0.1μm which is much smaller than the backlash of the EM motors. Vibration suppression in space structures and military vehicles also require compact but mighty piezoelectric actuators.

  8. Piezoelectric wave motor

    DOEpatents

    Yerganian, Simon Scott

    2001-07-17

    A piezoelectric motor having a stator in which piezoelectric elements are contained in slots formed in the stator transverse to the desired wave motion. When an electric field is imposed on the elements, deformation of the elements imposes a force perpendicular to the sides of the slot, deforming the stator. Appropriate frequency and phase shifting of the electric field will produce a wave in the stator and motion in a rotor. In a preferred aspect, the piezoelectric elements are configured so that deformation of the elements in direction of an imposed electric field, generally referred to as the d.sub.33 direction, is utilized to produce wave motion in the stator. In a further aspect, the elements are compressed into the slots so as to minimize tensile stresses on the elements in use.

  9. Piezoelectric wave motor

    DOEpatents

    Yerganian, Simon Scott

    2003-02-11

    A piezoelectric motor having a stator in which piezoelectric elements are contained in slots formed in the stator transverse to the desired wave motion. When an electric field is imposed on the elements, deformation of the elements imposes a force perpendicular to the sides of the slot, deforming the stator. Appropriate frequency and phase-shifting of the electric field will produce a wave in the stator and motion in a rotor. In a preferred aspect, the piezoelectric elements are configured so that deformation of the elements in the direction of an imposed electric field, generally referred to as the d.sub.33 direction, is utilized to produce wave motion in the stator. In a further aspect, the elements are compressed into the slots so as to minimize tensile stresses on the elements in use.

  10. Corrosion Behavior of Pulsed Gas Tungsten Arc Weldments in Power Plant Carbon Steel

    NASA Astrophysics Data System (ADS)

    Kumaresh Babu, S. P.; Natarajan, S.

    2007-10-01

    Welding plays an essential role in fabrication of components such as boiler drum, pipe work, heat exchangers, etc., used in power plants. Gas tungsten arc welding (GTAW) is mainly used for welding of boiler components. Pulsed GTAW is another process widely used where high quality and precision welds are required. In all arc-welding processes, the intense heat produced by the arc and the associated local heating and cooling lead to varied corrosion behavior and several metallurgical phase changes. Since the occurrence of corrosion is due to electrochemical potential gradient developed in the adjacent site of a weld metal, it is proposed to study the effects of welding on the corrosion behavior of these steels. This paper describes the experimental work carried out to evaluate and compare corrosion and its inhibition in SA 516 Gr.70 carbon steel by pulsed GTAW process in HCl medium at 0.1, 0.5, and 1.0 M concentrations. The parent metal, weld metal and heat affected zone are chosen as regions of exposure for the study made at room temperature (R.T.) and at 100 °C. Electrochemical polarization techniques such as Tafel line extrapolation (Tafel), linear polarization resistance (LPR), and ac impedance method have been used to measure the corrosion current. The role of hexamine and mixed inhibitor (thiourea + hexamine in 0.5 M HCl), each at 100 ppm concentration is studied in these experiments. Microstructural observation, surface characterization, and morphology using SEM and XRD studies have been made on samples exposed at 100 °C in order to highlight the nature and extent of film formation.

  11. Piezoelectric allostery of protein.

    PubMed

    Ohnuki, Jun; Sato, Takato; Takano, Mitsunori

    2016-07-01

    Allostery is indispensable for a protein to work, where a locally applied stimulus is transmitted to a distant part of the molecule. While the allostery due to chemical stimuli such as ligand binding has long been studied, the growing interest in mechanobiology prompts the study of the mechanically stimulated allostery, the physical mechanism of which has not been established. By molecular dynamics simulation of a motor protein myosin, we found that a locally applied mechanical stimulus induces electrostatic potential change at distant regions, just like the piezoelectricity. This novel allosteric mechanism, "piezoelectric allostery", should be of particularly high value for mechanosensor/transducer proteins. PMID:27575163

  12. Piezoelectric allostery of protein

    NASA Astrophysics Data System (ADS)

    Ohnuki, Jun; Sato, Takato; Takano, Mitsunori

    2016-07-01

    Allostery is indispensable for a protein to work, where a locally applied stimulus is transmitted to a distant part of the molecule. While the allostery due to chemical stimuli such as ligand binding has long been studied, the growing interest in mechanobiology prompts the study of the mechanically stimulated allostery, the physical mechanism of which has not been established. By molecular dynamics simulation of a motor protein myosin, we found that a locally applied mechanical stimulus induces electrostatic potential change at distant regions, just like the piezoelectricity. This novel allosteric mechanism, "piezoelectric allostery", should be of particularly high value for mechanosensor/transducer proteins.

  13. Piezoelectric and pyroelectric polymers

    SciTech Connect

    Davis, G.T.

    1995-12-01

    Many polar polymers can be made to exhibit piezoelectric and pyroelectric properties by permanently aligning their dipoles in an electric field. The largest response is found in semi-crystalline polymers which exhibit a polar crystal phase which is amenable to reorientation in an applied electric field. The properties of poly(vinylidenefluoride), copolymers of vinyl idenefluoride and trifluoroethylene, nylon 7 and nylon 11 are compared. Polarization distribution across the thickness of such polymer films are discussed and novel techniques for the construction of piezoelectric bimorphs from the above copolymers are presented.

  14. Controlling the length of plasma waveguide up to 5 mm, produced by femtosecond laser pulses in atomic clustered gas.

    PubMed

    Mohamed, Walid Tawfik; Chen, Guanglong; Kim, Jaehoon; Tao, Geng Xiao; Ahn, Jungkwen; Kim, Dong Eon

    2011-08-15

    We report the observation of longitudinally uniform plasma waveguide with a controlled length of up to nearly 5 mm, in argon clustered gas jet. This self-channeling plasma is obtained using a 35 mJ, 30 fs FWHM pulse as a pump laser pulse to create the plasma channel. A 1 mJ pulse of the same laser is used for probing the plasma channels using interferometric diagnostics. The radial distribution of the electron density confirms the formation of a plasma waveguide. Clustered argon enhances the absorption efficiency of femtosecond pulses which enables the use of pump pulses of only 35 mJ, approximately 10 times less energy than required for heating conventional gas targets. The plasma channel length is controlled by the laser focus point (F), the laser intensity (I), the pump-probe delay time (t) and the laser height from a nozzle (z). The variation of the electron density for these parameters is also studied. We found that the highest density of 1.2 x 10(19) cm(-3) was obtained at I = 5.2 x 10(16) W/cm(2), z = 2 mm and t = 7.6 ns. It was demonstrated that by using a clustered jet, both the plasma waveguide length and the plasma density could be controlled. PMID:21934955

  15. Effect of background gas pressure and laser pulse intensity on laser induced plasma radiation of copper samples

    NASA Astrophysics Data System (ADS)

    Mehrabian, S.; Aghaei, M.; Tavassoli, S. H.

    2010-04-01

    Study of laser induced plasma emission of Cu in one dimension is numerically carried out. Effects of different background gas pressure (He), 100, 500, and 760 torr, and laser pulse intensities, 0.5, 0.7, and 1 GW/cm2, on the plasma emission as well as ablation processes are investigated. Under a specified condition, heat conduction equation in the target accompanied with gas dynamic equations in the plume is solved simultaneously. The mentioned equations are coupled to each other through the Knudsen layer conditions and the energy and mass balances at the interface between the target and the vapor. The Bremsstrahlung radiation of plasma and the spectral emission of copper atoms are studied under various background gas pressure and laser pulse intensities. Furthermore, number density of He, Cu, and the electron, pressure, and temperature of the plume under various conditions are obtained. In the early time after laser pulse, plasma radiation is mainly due to the Bremsstrahlung radiation while after some 10 ns, the plasma radiation is dominated by spectral emission of Cu atoms. A similar uncoupling is observed spatially. The Bremsstrahlung emission is dominant near the sample surface while at farther points the spectral emission is the dominant one. By increase in the background pressure and also the pulse intensity, the dominancy of the spectral emission would occur later in time and farther in position.

  16. Piezoelectric MEMS for energy harvesting

    NASA Astrophysics Data System (ADS)

    Kanno, Isaku

    2015-12-01

    Recently, piezoelectric MEMS have been intensively investigated to create new functional microdevices, and some of them have already been commercialized such as MEMS gyrosensors or miropumps of inkjet printer head. Piezoelectric energy harvesting is considered to be one of the promising future applications of piezoelectric MEMS. In this report, we introduce the deposition of the piezoelectric PZT thin films as well as lead-free KNN thin films. We fabricated piezoelectric energy harvesters of PZT and KNN thin films deposited on stainless steel cantilevers and compared their power generation performance.

  17. Induced piezoelectricity in isotropic biomaterial.

    PubMed

    Zimmerman, R L

    1976-12-01

    Isotropic material can be made to exhibit piezoelectric effects by the application of a constant electric field. For insulators, the piezoelectric strain constant is proportional to the applied electric field and for semiconductors, an additional out-of-phase component of piezoelectricity is proportional to the electric current density in the sample. The two induced coefficients are proportional to the strain-dependent dielectric constant (depsilon/dS + epsilon) and resistivity (drho/dS - rho), respectively. The latter is more important at frequencies such that rhoepsilonomega less than 1, often the case in biopolymers. Signals from induced piezoelectricity in nature may be larger than those from true piezoelectricity. PMID:990389

  18. A Chemical Detector for Gas Chromatography Using Pulsed Discharge Emission Spectroscopy on a Microchip

    NASA Astrophysics Data System (ADS)

    Luo, X.; Zhu, W.; Mitra, B.; Liu, J.; Liu, T.; Fan, X.; Gianchandani, Y.

    2011-12-01

    There is increasing interest in miniaturized systems for chemical analysis in harsh environments. Chemical detection by emission spectroscopy of on-chip microdischarges [1-3] can be performed at >200°C [4], suggesting utility inspace exploration, volcanic monitoring, and oil well monitoring. This abstract describes the first use of pulsed microdischarge spectroscopy for gas chromatography (GC).This effort supports NASA interests in monitoring closed-loop life support systems for spacecraft. The microdischarge occurs on a 1cm2 glass chip (Fig. 1a), with thin-film Ni electrodes separated by 160μm. A glass lid with a grooved gas-flow channel, and inlet/outlet capillary tubes are epoxy-sealed to the chip. Located downstream of the 1.7m-long, RTX-1-coated, GC separation column, the microdischarge chip is read by a spectrometer. In a typical experiment (Fig. 1b), a mixture of acetone 3.6μg, 1-hexanol 2.8μg and nitrobenzene 3.0μg, is injected, with He carrier gas at 1.56sccm, through the GC. Acetone elutes quickly while nitrobenzene is slower. Microdischarges are triggered at 0.5Hz for 6 min., and 0.04Hz thereafter. Each microdischarge consumes ≈8mJ; the average power is ≈1.14mW. The spectrum (Fig. 1b, inset) shows that the 388nm peak, representing CN/CH fragments [5], is enhanced by carbon compounds. Its strength relative to the 588nm peak of He provides a chromatogram. Fig. 1b also shows a benchmark result from a commercial flame ionization detector (FID). The differences in elution time are attributed to differences in the gas flow paths for the two detectors [1]. REFERENCES [1] Eijkel et al, Anal. Chem, 2000 [2] Mitra et al, IEEE Trans Plasma Sci, 2008 [3] Mitra et al, IEEE Sensors, 2008 [4] Wright et al, APL, 2009 [5] Pearse et al, The Identification of Molecular Spectra, 1963

  19. Small Gas Bubble Experiment for Mitigation of Cavitation Damage and Pressure Waves in Short-pulse Mercury Spallation Targets

    SciTech Connect

    Wendel, Mark W; Felde, David K; Sangrey, Robert L; Abdou, Ashraf A; West, David L; Shea, Thomas J; Hasegawa, Shoichi; Kogawa, Hiroyuki; Naoe, Dr. Takashi; Farny, Dr. Caleb H.; Kaminsky, Andrew L

    2014-01-01

    Populations of small helium gas bubbles were introduced into a flowing mercury experiment test loop to evaluate mitigation of beam-pulse induced cavitation damage and pressure waves. The test loop was developed and thoroughly tested at the Spallation Neutron Source (SNS) prior to irradiations at the Los Alamos Neutron Science Center - Weapons Neutron Research Center (LANSCE-WNR) facility. Twelve candidate bubblers were evaluated over a range of mercury flow and gas injection rates by use of a novel optical measurement technique that accurately assessed the generated bubble size distributions. Final selection for irradiation testing included two variations of a swirl bubbler provided by Japan Proton Accelerator Research Complex (J-PARC) collaborators and one orifice bubbler developed at SNS. Bubble populations of interest consisted of sizes up to 150 m in radius with achieved gas void fractions in the 10^-5 to 10^-4 range. The nominal WNR beam pulse used for the experiment created energy deposition in the mercury comparable to SNS pulses operating at 2.5 MW. Nineteen test conditions were completed each with 100 pulses, including variations on mercury flow, gas injection and protons per pulse. The principal measure of cavitation damage mitigation was surface damage assessment on test specimens that were manually replaced for each test condition. Damage assessment was done after radiation decay and decontamination by optical and laser profiling microscopy with damaged area fraction and maximum pit depth being the more valued results. Damage was reduced by flow alone; the best mitigation from bubble injection was between half and a quarter that of flow alone. Other data collected included surface motion tracking by three laser Doppler vibrometers (LDV), loop wall dynamic strain, beam diagnostics for charge and beam profile assessment, embedded hydrophones and pressure sensors, and sound measurement by a suite of conventional and contact microphones.

  20. Improved operation of a microwave pulse compressor with a laser-triggered high-pressure gas plasma switch

    NASA Astrophysics Data System (ADS)

    Shlapakovski, A.; Gorev, S.; Krasik, Ya. E.

    2016-08-01

    The influence of laser beam parameters on the output pulses of a resonant microwave compressor with a laser-triggered plasma switch was investigated. The S-band compressor, consisting of a rectangular waveguide-based cavity and H-plane waveguide tee with a shorted side arm, was filled with pressurized dry air and pumped by 1.8-μs-long microwave pulses of up to 450 kW power. A Nd:YAG laser was used to ignite the gas discharge in the tee side arm for output pulse extraction. The laser beam (at 213 nm or 532 nm) was directed along the RF electric field lines. It was found that the compressor operated most effectively when the laser beam was focused at the center of the switch waveguide cross-section. In this case, the power extraction efficiency reached ˜47% at an output power of ˜14 MW, while when the laser beam was not focused the maximal extraction efficiency was only ˜20% at ˜6 MW output power. Focusing the laser beam resulted also in a dramatic decrease (down to <1 ns) in the delay of the output pulses' appearance with respect to the time of the beam's entrance into the switch, and the jitter of the output pulses' appearance was minimized. In addition, the quality of the output pulses' waveform was significantly improved.

  1. UHV piezoelectric translator

    SciTech Connect

    Oversluizen, T.; Watson, G.

    1985-01-01

    A UHV compatible piezoelectric translator has been developed to correct for angular misalignments in the crysals of a UHV x-ray monochromator. The unit is small, bakeable to 150/sup 0/C, and uses only ceramic materials for insulation. We report on the construction details, vacuum compatibility, mechanical properties, and uses of the device.

  2. Tortuosity measurement and the effects of finite pulse widths on xenon gas diffusion NMR studies of porous media

    NASA Technical Reports Server (NTRS)

    Mair, R. W.; Hurlimann, M. D.; Sen, P. N.; Schwartz, L. M.; Patz, S.; Walsworth, R. L.

    2001-01-01

    We have extended the utility of NMR as a technique to probe porous media structure over length scales of approximately 100-2000 microm by using the spin 1/2 noble gas 129Xe imbibed into the system's pore space. Such length scales are much greater than can be probed with NMR diffusion studies of water-saturated porous media. We utilized Pulsed Gradient Spin Echo NMR measurements of the time-dependent diffusion coefficient, D(t), of the xenon gas filling the pore space to study further the measurements of both the pore surface-area-to-volume ratio, S/V(p), and the tortuosity (pore connectivity) of the medium. In uniform-size glass bead packs, we observed D(t) decreasing with increasing t, reaching an observed asymptote of approximately 0.62-0.65D(0), that could be measured over diffusion distances extending over multiple bead diameters. Measurements of D(t)/D(0) at differing gas pressures showed this tortuosity limit was not affected by changing the characteristic diffusion length of the spins during the diffusion encoding gradient pulse. This was not the case at the short time limit, where D(t)/D(0) was noticeably affected by the gas pressure in the sample. Increasing the gas pressure, and hence reducing D(0) and the diffusion during the gradient pulse served to reduce the previously observed deviation of D(t)/D(0) from the S/V(p) relation. The Pade approximation is used to interpolate between the long and short time limits in D(t). While the short time D(t) points lay above the interpolation line in the case of small beads, due to diffusion during the gradient pulse on the order of the pore size, it was also noted that the experimental D(t) data fell below the Pade line in the case of large beads, most likely due to finite size effects.

  3. Tortuosity measurement and the effects of finite pulse widths on xenon gas diffusion NMR studies of porous media.

    PubMed

    Mair, R W; Hürlimann, M D; Sen, P N; Schwartz, L M; Patz, S; Walsworth, R L

    2001-01-01

    We have extended the utility of NMR as a technique to probe porous media structure over length scales of approximately 100-2000 microm by using the spin 1/2 noble gas 129Xe imbibed into the system's pore space. Such length scales are much greater than can be probed with NMR diffusion studies of water-saturated porous media. We utilized Pulsed Gradient Spin Echo NMR measurements of the time-dependent diffusion coefficient, D(t), of the xenon gas filling the pore space to study further the measurements of both the pore surface-area-to-volume ratio, S/V(p), and the tortuosity (pore connectivity) of the medium. In uniform-size glass bead packs, we observed D(t) decreasing with increasing t, reaching an observed asymptote of approximately 0.62-0.65D(0), that could be measured over diffusion distances extending over multiple bead diameters. Measurements of D(t)/D(0) at differing gas pressures showed this tortuosity limit was not affected by changing the characteristic diffusion length of the spins during the diffusion encoding gradient pulse. This was not the case at the short time limit, where D(t)/D(0) was noticeably affected by the gas pressure in the sample. Increasing the gas pressure, and hence reducing D(0) and the diffusion during the gradient pulse served to reduce the previously observed deviation of D(t)/D(0) from the S/V(p) relation. The Pade approximation is used to interpolate between the long and short time limits in D(t). While the short time D(t) points lay above the interpolation line in the case of small beads, due to diffusion during the gradient pulse on the order of the pore size, it was also noted that the experimental D(t) data fell below the Pade line in the case of large beads, most likely due to finite size effects. PMID:11445310

  4. Dynamics of rare gas nanoclusters irradiated by short and intense laser pulses

    NASA Astrophysics Data System (ADS)

    Micheau, S.; Bonté, C.; Dorchies, F.; Fourment, C.; Harmand, M.; Jouin, H.; Peyrusse, O.; Pons, B.; Santos, J. J.

    2007-05-01

    We report on a joint experimental-theoretical effort to shed light on the dynamics of rare gas (Ar) nanoclusters irradiated by short and intense laser pulses. The experiments employ a streak camera coupled to a conical crystal to yield energy- and time-resolved X-ray spectra, in the keV range on picosecond scale. These spectra display ultrafast subpicosecond ionization dynamics, leading to highly charged states such as Ar 16+, and indicate that the duration of the energetic X-rays is less than the experimental 1.3 ps temporal resolution. The theoretical calculations rely on the well-known nanoplasma model, which has been improved to represent the collisional ionization processes that are of importance in nanoplasma dynamics. Allowance is made for high-order ionization transitions involving intermediate excited states. The simulations indicate significant populations of excited states of highly charged ions, in agreement with the experimental findings. Further, detailed collisional-radiative calculations indicate that the duration of the X-ray bursts is less than 100 fs.

  5. A model for the secondary scintillation pulse shape from a gas proportional scintillation counter

    NASA Astrophysics Data System (ADS)

    Kazkaz, K.; Joshi, T. H.

    2016-03-01

    Proportional scintillation counters (PSCs), both single- and dual-phase, can measure the scintillation (S1) and ionization (S2) channels from particle interactions within the detector volume. The signal obtained from these detectors depends first on the physics of the medium (the initial scintillation and ionization), and second how the physics of the detector manipulates the resulting photons and liberated electrons. In this paper we develop a model of the detector physics that incorporates event topology, detector geometry, electric field configuration, purity, optical properties of components, and wavelength shifters. We present an analytic form of the model, which allows for general study of detector design and operation, and a Monte Carlo model which enables a more detailed exploration of S2 events. This model may be used to study systematic effects in current detectors such as energy and position reconstruction, pulse shape discrimination, event topology, dead time calculations, purity, and electric field uniformity. We present a comparison of this model with experimental data collected with an argon gas proportional scintillation counter (GPSC), operated at 20 C and 1 bar, and irradiated with an internal, collimated 55Fe source. Additionally we discuss how the model may be incorporated in Monte Carlo simulations of both GPSCs and dual-phase detectors, increasing the reliability of the simulation results and allowing for tests of the experimental data analysis algorithms.

  6. Electron-ion collision rates in noble gas clusters irradiated by femtosecond laser pulse

    NASA Astrophysics Data System (ADS)

    Dey, R.; Roy, A. C.

    2012-05-01

    We report a theoretical analysis of electron-ion collision rates in xenon gas clusters irradiated by femtosecond laser pulses. The present analysis is based on the eikonal approximation (EA), the first Born approximation (FBA) and the classical (CL) methods. The calculations are performed using the plasma-screened Rogers potential introduced by Moll et al. [J. Phys. B. 43, 135103 (2010)] as well as the Debye potential for a wide range of experimental parameters. We find that the magnitudes of electron-ion collision frequency obtained in the EA do not fall as rapidly with the kinetic energy of electrons as in the FBA and CL methods for higher charge states of xenon ion (Xe8+ and Xe14+). Furthermore, EA shows that the effect of the inner structure of ion is most dominant for the lowest charge state of xenon ion (Xe1+). In the case of the present effective potential, FBA overestimates the CL results for all three different charge states of xenon, whereas for the Debye potential, both the FBA and CL methods predict collision frequencies which are nearly close to each other.

  7. Plasma structures observed in gas breakdown using a 1.5 MW, 110 GHz pulsed gyrotron

    SciTech Connect

    Hidaka, Yoshiteru; Choi, E. M.; Mastovsky, I.; Shapiro, M. A.; Sirigiri, J. R.; Temkin, R. J.; Edmiston, G. F.; Neuber, A. A.; Oda, Y.

    2009-05-15

    Regular two-dimensional plasma filamentary arrays have been observed in gas breakdown experiments using a pulsed 1.5 MW, 110 GHz gyrotron. The gyrotron Gaussian output beam is focused to an intensity of up to 4 MW/cm{sup 2}. The plasma filaments develop in an array with a spacing of about one quarter wavelength, elongated in the electric field direction. The array was imaged using photodiodes, a slow camera, which captures the entire breakdown event, and a fast camera with a 6 ns window. These diagnostics demonstrate the sequential development of the array propagating back toward the source. Gases studied included air, nitrogen, SF{sub 6}, and helium at various pressures. A discrete plasma array structure is observed at high pressure, while a diffuse plasma is observed at lower pressure. The propagation speed of the ionization front for air and nitrogen at atmospheric pressure for 3 MW/cm{sup 2} was found to be of the order of 10 km/s.

  8. Ionization heating in rare-gas clusters under intense XUV laser pulses

    SciTech Connect

    Arbeiter, Mathias; Fennel, Thomas

    2010-07-15

    The interaction of intense extreme ultraviolet (XUV) laser pulses ({lambda}=32 nm, I=10{sup 11}-10{sup 14} W/cm{sup 2}) with small rare-gas clusters (Ar{sub 147}) is studied by quasiclassical molecular dynamics simulations. Our analysis supports a very general picture of the charging and heating dynamics in finite samples under short-wavelength radiation that is of relevance for several applications of free-electron lasers. First, up to a certain photon flux, ionization proceeds as a series of direct photoemission events producing a jellium-like cluster potential and a characteristic plateau in the photoelectron spectrum as observed in Bostedt et al. [Phys. Rev. Lett. 100, 133401 (2008)]. Second, beyond the onset of photoelectron trapping, nanoplasma formation leads to evaporative electron emission with a characteristic thermal tail in the electron spectrum. A detailed analysis of this transition is presented. Third, in contrast to the behavior in the infrared or low vacuum ultraviolet range, the nanoplasma energy capture proceeds via ionization heating, i.e., inner photoionization of localized electrons, whereas collisional heating of conduction electrons is negligible up to high laser intensities. A direct consequence of the latter is a surprising evolution of the mean energy of emitted electrons as function of laser intensity.

  9. Experimental Observation of the Pulsed High Pressure Gas Puffing on HL-2A Tokamak

    NASA Astrophysics Data System (ADS)

    Shi, Zhongbing; Ding, Xuantong; Yao, Lianghua; Liu, Zetian; Chen, Chengyuan; Yang, Qingwei; Feng, Beibin; Zhou, Yan; Yan, Longwen; Liu, Yi; Liu, Yong

    2006-01-01

    The pulse propagations of both the electron temperature and the electron density have been observed during pulse-modulated molecular beam injection experiments on HL-2A. The propagation depth of the cold pulse in the low field side is much longer than that in the high field side. The cold pulses cannot propagate to the plasma center from either the low field side or the high field side. The electron temperature in the plasma center does not change during MBI, but the electron density pulse perturbations can be observed in the plasma center.

  10. High-energy noncollinear optical parametric amplifier producing 4  fs pulses in the visible seeded by a gas-phase filament.

    PubMed

    Odhner, Johanan H; Levis, Robert J

    2015-08-15

    We report on the design and characterization of a short-pulse-pumped, single-stage noncollinear optical parametric amplifier (NOPA) that achieves high pulse energies in the few-cycle pulse regime. Optimal pulse-front tilting and temporal compression of the short (35 fs) pump pulse are achieved using a 4f grating compressor, while spatial chirp at the NOPA crystal is eliminated with proper imaging using a pair of reflective telescopes. Gas-phase filamentation in an open-ended argon-filled cell provides a bright, stable seed source with little residual chirp that is suitable for temporal overlap with the short pump pulse without dispersion precompensation. Two seeding geometries are explored, and pulses as short as 3.5 fs are obtained by seeding with the entire filament bandwidth. Fourier-transform-limited 4 fs pulses are obtained by filtering the IR portion of the spectrum. PMID:26274667

  11. The narrow pulse approximation and long length scale determination in xenon gas diffusion NMR studies of model porous media

    NASA Technical Reports Server (NTRS)

    Mair, R. W.; Sen, P. N.; Hurlimann, M. D.; Patz, S.; Cory, D. G.; Walsworth, R. L.

    2002-01-01

    We report a systematic study of xenon gas diffusion NMR in simple model porous media, random packs of mono-sized glass beads, and focus on three specific areas peculiar to gas-phase diffusion. These topics are: (i) diffusion of spins on the order of the pore dimensions during the application of the diffusion encoding gradient pulses in a PGSE experiment (breakdown of the narrow pulse approximation and imperfect background gradient cancellation), (ii) the ability to derive long length scale structural information, and (iii) effects of finite sample size. We find that the time-dependent diffusion coefficient, D(t), of the imbibed xenon gas at short diffusion times in small beads is significantly affected by the gas pressure. In particular, as expected, we find smaller deviations between measured D(t) and theoretical predictions as the gas pressure is increased, resulting from reduced diffusion during the application of the gradient pulse. The deviations are then completely removed when water D(t) is observed in the same samples. The use of gas also allows us to probe D(t) over a wide range of length scales and observe the long time asymptotic limit which is proportional to the inverse tortuosity of the sample, as well as the diffusion distance where this limit takes effect (approximately 1-1.5 bead diameters). The Pade approximation can be used as a reference for expected xenon D(t) data between the short and the long time limits, allowing us to explore deviations from the expected behavior at intermediate times as a result of finite sample size effects. Finally, the application of the Pade interpolation between the long and the short time asymptotic limits yields a fitted length scale (the Pade length), which is found to be approximately 0.13b for all bead packs, where b is the bead diameter. c. 2002 Elsevier Sciences (USA).

  12. The narrow pulse approximation and long length scale determination in xenon gas diffusion NMR studies of model porous media.

    PubMed

    Mair, R W; Sen, P N; Hürlimann, M D; Patz, S; Cory, D G; Walsworth, R L

    2002-06-01

    We report a systematic study of xenon gas diffusion NMR in simple model porous media, random packs of mono-sized glass beads, and focus on three specific areas peculiar to gas-phase diffusion. These topics are: (i) diffusion of spins on the order of the pore dimensions during the application of the diffusion encoding gradient pulses in a PGSE experiment (breakdown of the narrow pulse approximation and imperfect background gradient cancellation), (ii) the ability to derive long length scale structural information, and (iii) effects of finite sample size. We find that the time-dependent diffusion coefficient, D(t), of the imbibed xenon gas at short diffusion times in small beads is significantly affected by the gas pressure. In particular, as expected, we find smaller deviations between measured D(t) and theoretical predictions as the gas pressure is increased, resulting from reduced diffusion during the application of the gradient pulse. The deviations are then completely removed when water D(t) is observed in the same samples. The use of gas also allows us to probe D(t) over a wide range of length scales and observe the long time asymptotic limit which is proportional to the inverse tortuosity of the sample, as well as the diffusion distance where this limit takes effect (approximately 1-1.5 bead diameters). The Padé approximation can be used as a reference for expected xenon D(t) data between the short and the long time limits, allowing us to explore deviations from the expected behavior at intermediate times as a result of finite sample size effects. Finally, the application of the Padé interpolation between the long and the short time asymptotic limits yields a fitted length scale (the Padé length), which is found to be approximately 0.13b for all bead packs, where b is the bead diameter. PMID:12165255

  13. Tunable vacuum-UV to visible ultrafast pulse source based on gas-filled Kagome-PCF.

    PubMed

    Mak, Ka Fai; Travers, John C; Hölzer, Philipp; Joly, Nicolas Y; Russell, Philip St J

    2013-05-01

    An efficient and tunable 176-550 nm source based on the emission of resonant dispersive radiation from ultrafast solitons at 800 nm is demonstrated in a gas-filled hollow-core photonic crystal fiber (PCF). By careful optimization and appropriate choice of gas, informed by detailed numerical simulations, we show that bright, high quality, localized bands of UV light (relative widths of a few percent) can be generated at all wavelengths across this range. Pulse energies of more than 75 nJ in the deep-UV, with relative bandwidths of ~3%, are generated from pump pulses of a few μJ. Excellent agreement is obtained between numerical and experimental results. The effects of positive and negative axial pressure gradients are also experimentally studied, and the coherence of the deep-UV dispersive wave radiation numerically investigated. PMID:23669950

  14. Interface cracks in piezoelectric materials

    NASA Astrophysics Data System (ADS)

    Govorukha, V.; Kamlah, M.; Loboda, V.; Lapusta, Y.

    2016-02-01

    Due to their intrinsic electromechanical coupling behavior, piezoelectric materials are widely used in sensors, actuators and other modern technologies. It is well known that piezoelectric ceramics are very brittle and susceptible to fracture. In many cases, fracture occurs at interfaces as debonding and cracks. This leads to an undesired degradation of electrical and mechanical performance. Because of the practical and fundamental importance of the problem, interface cracks in piezoelectric materials have been actively studied in the last few decades. This review provides a comprehensive survey of recent works on cracks situated at the interface of two materials, at least one of which has piezoelectric or piezoelectromagnetic properties. Different electric boundary conditions along the crack faces are discussed. The oscillating and contact zone models for in-plane straight interface cracks between two dissimilar piezoelectric materials or between piezoelectric and non-piezoelectric ones are reviewed. Different peculiarities related to the investigation of interface cracks in piezoelectric materials for the anti-plane case, for functionally graded and thermopiezoelectric materials are presented. Papers related to magnetoelectroelastic bimaterials, to steady state motion of interface cracks in piezoelectric bimaterials and to circular arc-cracks at the interface of piezoelectric materials are reviewed, and various methods used to address these problems are discussed. The review concludes with an outlook on future research directions.

  15. Influence of ambient gas on the microstructural properties of Er-doped nanocrystalline Si film fabricated by pulsed laser ablation

    NASA Astrophysics Data System (ADS)

    Zhou, Yang; Chu, Lizhi; Duan, Pingguang; Xu, Wei; Wang, Yinglong; F, Guangsheng

    2007-12-01

    Er-doped nanocrystalline Si thin films were fabricated by pulsed laser ablation in high-purity Ar gas with different gas pressures at room temperature and post-annealing technology under different temperature in nitrogen. Scanning electron microscopy(SEM), x-ray diffraction(XRD) and Raman were employed to picture the microstructure of films. The SEM photographs showed that the morphology of film was transformed from the uniform nanoparticles in size to the web-like structure with the increase of gas pressure, which was attributed to the different collision cooling process of ablated particles. Raman and XRD spectra showed that the introduction of Ar gas could effectively improve the crystallinity degree of the samples and Si nanoparticle size could be controlled by adjusting the post-annealing temperature which was critical for improving the luminescent intensity of Er 3+ ion. More uniform and higher crystallinity degree Er-doped Si thin films could be obtained at lower annealing temperature.

  16. Dynamic mechanism of the velocity splitting of ablated particles produced by pulsed-laser deposition in an inert gas

    NASA Astrophysics Data System (ADS)

    Ding, X. C.; Wang, Y. L.; Chu, L. Z.; Deng, Z. C.; Liang, W. H.; Galalaldeen, I. I. A.; Fu, G. S.

    2011-12-01

    The transport dynamics of ablated particles produced by pulsed-laser deposition in an inert gas is investigated via the Monte Carlo simulation method. The splitting mechanism of ablated particles is discussed by tracking every ablated particle with their forces, velocities and locations. The force analysis demonstrates that whether the splitting appears or not is decided by the releasing way of the driving force acting on the ablated particles. The "average" drag force, which is related to the mass and radius of the ambient gas, determines the releasing way of the driving force. Our simulated results are approximately in agreement with the previous experimental data.

  17. Bremsstrahlung {gamma}-ray generation by electrons from gas jets irradiated by laser pulses for radiographic testing

    SciTech Connect

    Oishi, Yuji; Nayuki, Takuya; Zhidkov, Alexei; Fujii, Takashi; Nemoto, Koshichi

    2012-07-11

    Electron generation from a gas jet irradiated by low energy femtosecond laser pulses is studied experimentally as a promising source of radiation for radioisotope-free {gamma}-ray imaging systems. The calculated yield of {gamma}-rays in the 0.5-2 MeV range, produced by low-average-power lasers and gas targets, exceeds the yields from solid tape targets up to 60 times. In addition, an effect of quasi-mono energetic electrons on {gamma}-ray imaging is also discussed.

  18. An atmospheric air gas-liquid diffuse discharge excited by bipolar nanosecond pulse in quartz container used for water sterilization

    NASA Astrophysics Data System (ADS)

    Wang, Sen; Yang, De-Zheng; Wang, Wen-Chun; Zhang, Shuai; Liu, Zhi-Jie; Tang, Kai; Song, Ying

    2013-12-01

    In this Letter, we report that the air gas-liquid diffuse discharge plasma excited by bipolar nanosecond pulse in quartz container with different bottom structures at atmospheric pressure. Optical diagnostic measurements show that bountiful chemically and biologically active species, which are beneficial for effective sterilization in some areas, are produced. Such diffuse plasmas are then used to treat drinking water containing the common microorganisms (Candida albicans and Escherichia coli). It is found that these plasmas can sterilize the microorganisms efficiently.

  19. Sterilization of Fungus in Water by Pulsed Power Gas Discharge Reactor Spraying Water Droplets for Water Treatment

    NASA Astrophysics Data System (ADS)

    Saito, Tsukasa; Handa, Taiki; Minamitani, Yasushi

    We study sterilization of bacteria in water using pulsed streamer discharge of gas phase. This method enhances efficiency of water treatment by spraying pretreatment water in a streamer discharge area. In this paper, yeast was sterilized because we assumed a case that fungus like mold existed in wastewater. As a result, colony forming units decreased rapidly for 2 minutes of the processing time, and all yeast sterilized by 45 minutes of the processing time.

  20. Combined soliton pulse compression and plasma-related frequency upconversion in gas-filled photonic crystal fiber.

    PubMed

    Chang, W; Hölzer, P; Travers, J C; Russell, P St J

    2013-08-15

    We numerically investigate self-frequency blueshifting of a fundamental soliton in a gas-filled hollow-core photonic crystal fiber. Because of the changing underlying soliton parameters, the blueshift gives rise to adiabatic soliton compression. Based on these features, we propose a device that enables frequency shifting over an octave and pulse compression from 30 fs down to 2.3 fs. PMID:24104627

  1. Model of a Piezoelectric Transducer

    NASA Technical Reports Server (NTRS)

    Goodenow, Debra

    2004-01-01

    It's difficult to control liquid and gas in propellant tanks in zero gravity. A possible a design would utilize acoustic liquid manipulation (ALM) technology which uses ultrasonic beams conducted through a liquid and solid media, to push gas bubbles in the liquid to desirable locations. We can propel and control the bubble with acoustic radiation pressure by aiming the acoustic waves on the bubble s surface. This allows us to design a so called smart tank in which the ALM devices transfer the gas to the outer wall of the tank and isolating the liquid in the center. Because the heat transfer rate of a gas is lower of that of the liquid it would substantially decrease boil off and provide of for a longer storage life. The ALM beam is composed of little wavelets which are individual waves that constructively interfere with each other to produce a single, combined acoustic wave front. This is accomplished by using a set of synchronized ultrasound transducers arranged in an array. A slight phase offset of these elements allows us to focus and steer the beam. The device that we are using to produce the acoustic beam is called the piezoelectric transducer. This device converts electrical energy to mechanical energy, which appears in the form of acoustic energy. Therefore the behavior of the device is dependent on both the mechanical characteristics, such as its density, cross-sectional area, and its electrical characteristics, such as, electric flux permittivity and coupling factor. These devices can also be set up in a number of modes which are determined by the way the piezoelectric device is arranged, and the shape of the transducer. For this application we are using the longitudinal or thickness mode for our operation. The transducer also vibrates in the lateral mode, and one of the goals of my project is to decrease the amount of energy lost to the lateral mode. To model the behavior of the transducers I will be using Pspice, electric circuit modeling tool, to

  2. Epidermis of Human Skin: Pyroelectric and Piezoelectric Sensor Layer

    NASA Astrophysics Data System (ADS)

    Athenstaedt, Herbert; Claussen, Helge; Schaper, Daniel

    1982-05-01

    The epidermis of live human skin has a permanent electric dipole moment perpendicular to its surface. Voltage responses to a rapid change of temperature are pyroelectric, while voltage responses to pressure pulses are piezoelectric in nature. The time course of the responses depends on dX/dt (X, temperature or pressure). The epidermal surface can react to all physical environmental influences to which nonbiological pyroelectric materials are known to respond. Epidermal voltage signals can be perceived through the intraepidermal and the superficial dermal nervous network. The pyroelectric and piezoelectric properties are also measurable on dead, dry skin samples.

  3. Propagation of 0{pi} pulses in a gas of three-level atoms

    SciTech Connect

    Sun Dong; Sariyanni, Zoe-Elizabeth; Das, Sumanta; Rostovtsev, Yuri V.

    2011-06-15

    We have theoretically studied the pulsed regime of electromagnetically induced transparency. In particular, simulations of propagation of Gaussian and 0{pi} copropagating laser pulses in a medium consisting of three-level {Lambda} atoms have been performed. It has been found that even at the two-photon resonance, the length of propagation for the 0{pi} pulses is much smaller than the one for the Gaussian probe pulses. Using the dark and bright basis, we explain this behavior. Some possible applications are discussed.

  4. The impact of a pulsing groundwater table on greenhouse gas emissions in riparian grey alder stands.

    PubMed

    Mander, Ülo; Maddison, Martin; Soosaar, Kaido; Teemusk, Alar; Kanal, Arno; Uri, Veiko; Truu, Jaak

    2015-02-01

    Floods control greenhouse gas (GHG) emissions in floodplains; however, there is a lack of data on the impact of short-term events on emissions. We studied the short-term effect of changing groundwater (GW) depth on the emission of (GHG) carbon dioxide (CO2), methane (CH4), and nitrous oxide (N2O) in two riparian grey alder (Alnus incana) stands of different age in Kambja, southern Estonia, using the opaque static chamber (five replicates in each site) and gas chromatography methods. The average carbon and total nitrogen content in the soil of the old alder (OA) stand was significantly higher than in the young alder (YA) stand. In both stands, one part was chosen for water table manipulation (Manip) and another remained unchanged with a stable and deeper GW table. Groundwater table manipulation (flooding) significantly increases CH4 emission (average: YA-Dry 468, YA-Manip 8,374, OA-Dry 468, OA-Manip 4,187 μg C m(-2) h(-1)) and decreases both CO2 (average: OA-Dry 138, OA-Manip 80 mg C m(-2) h(-1)) and N2O emissions (average: OA-Dry 23.1, OA-Manip 11.8 μg N m(-2) h(-1)) in OA sites. There was no significant difference in CO2 and CH4 emissions between the OA and YA sites, whereas in OA sites with higher N concentration in the soil, the N2O emission was significantly higher than at the YA sites. The relative CO2 and CH4 emissions (the soil C stock-related share of gaseous losses) were higher in manipulated plots showing the highest values in the YA-Manip plot (0.03 and 0.0030 % C day(-1), respectively). The soil N stock-related N2O emission was very low achieving 0.000019 % N day(-1) in the OA-Dry plot. Methane emission shows a negative correlation with GW, whereas the 20 cm depth is a significant limit below which most of the produced CH4 is oxidized. In terms of CO2 and N2O, the deeper GW table significantly increases emission. In riparian zones of headwater streams, the short-term floods (e.g. those driven by extreme climate events) may significantly enhance

  5. Piezoelectric step-motion actuator

    DOEpatents

    Mentesana; Charles P.

    2006-10-10

    A step-motion actuator using piezoelectric material to launch a flight mass which, in turn, actuates a drive pawl to progressively engage and drive a toothed wheel or rod to accomplish stepped motion. Thus, the piezoelectric material converts electrical energy into kinetic energy of the mass, and the drive pawl and toothed wheel or rod convert the kinetic energy of the mass into the desired rotary or linear stepped motion. A compression frame may be secured about the piezoelectric element and adapted to pre-compress the piezoelectric material so as to reduce tensile loads thereon. A return spring may be used to return the mass to its resting position against the compression frame or piezoelectric material following launch. Alternative embodiment are possible, including an alternative first embodiment wherein two masses are launched in substantially different directions, and an alternative second embodiment wherein the mass is eliminated in favor of the piezoelectric material launching itself.

  6. High Temperature Piezoelectric Drill

    NASA Technical Reports Server (NTRS)

    Bao, Xiaoqi; Bar-Cohen, Yoseph; Sherrit, Stewart; Badescu, Mircea; Shrout, Tom

    2012-01-01

    Venus is one of the planets in the solar systems that are considered for potential future exploration missions. It has extreme environment where the average temperature is 460 deg C and its ambient pressure is about 90 atm. Since the existing actuation technology cannot maintain functionality under the harsh conditions of Venus, it is a challenge to perform sampling and other tasks that require the use of moving parts. Specifically, the currently available electromagnetic actuators are limited in their ability to produce sufficiently high stroke, torque, or force. In contrast, advances in developing electro-mechanical materials (such as piezoelectric and electrostrictive) have enabled potential actuation capabilities that can be used to support such missions. Taking advantage of these materials, we developed a piezoelectric actuated drill that operates at the temperature range up to 500 deg C and the mechanism is based on the Ultrasonic/Sonic Drill/Corer (USDC) configuration. The detailed results of our study are presented in this paper

  7. Formation of plasma channels in the interaction of a nanosecond laser pulse at moderate intensities with helium gas jets.

    PubMed

    De Wispelaere, E; Malka, V; Hüller, S; Amiranoff, F; Baton, S; Bonadio, R; Casanova, M; Dorchies, F; Haroutunian, R; Modena, A

    1999-06-01

    We report on a detailed study of channel formation in the interaction of a nanosecond laser pulse with a He gas jet. A complete set of diagnostics is used in order to characterize the plasma precisely. The evolution of the plasma radius and of the electron density and temperature are measured by Thomson scattering, Schlieren imaging, and Mach-Zehnder interferometry. In gas jets, one observes the formation of a channel with a deep density depletion on axis. Because of ionization-induced defocusing which increases the size of the focal spot and decreases the maximum laser intensity, no channel is observed in the case of a gas-filled chamber. The results obtained in various gas-jet and laser conditions show that the channel radius, as well as the density along the propagation axis, can be adjusted by changing the laser energy and gas-jet pressure. This is a crucial issue when one wants to adapt the channel parameters in order to guide a subsequent high-intensity laser pulse. The experimental results and their comparison with one-dimensional (1D) and two-dimensional hydrodynamic simulations show that the main mechanism for channel formation is the hydrodynamic evolution behind a supersonic electron heat wave propagating radially in the plasma. It is also shown from 2D simulations that a fraction of the long pulse can be self-guided in the channel it creates. The preliminary results and analyses on this subject have been published before [V. Malka et al., Phys. Rev. Lett. 79, 2979 (1997)]. PMID:11969699

  8. Piezoelectrically enhanced photocathode

    NASA Technical Reports Server (NTRS)

    Beach, Robert A. (Inventor); Nikzad, Shouleh (Inventor); Strittmatter, Robert P. (Inventor); Bell, Lloyd Douglas (Inventor)

    2009-01-01

    A photocathode, for generating electrons in response to incident photons in a photodetector, includes a base layer having a first lattice structure and an active layer having a second lattice structure and epitaxially formed on the base layer, the first and second lattice structures being sufficiently different to create a strain in the active layer with a corresponding piezoelectrically induced polarization field in the active layer, the active layer having a band gap energy corresponding to a desired photon energy.

  9. Black branes as piezoelectrics.

    PubMed

    Armas, Jay; Gath, Jakob; Obers, Niels A

    2012-12-14

    We find a realization of linear electroelasticity theory in gravitational physics by uncovering a new response coefficient of charged black branes, exhibiting their piezoelectric behavior. Taking charged dilatonic black strings as an example and using the blackfold approach we measure their elastic and piezolectric moduli. We also use our results to draw predictions about the equilibrium condition of charged dilatonic black rings in dimensions higher than six. PMID:23368298

  10. Improved Piezoelectric Loudspeakers And Transducers

    NASA Technical Reports Server (NTRS)

    Regan, Curtis Randall; Jalink, Antony; Hellbaum, Richard F.; Rohrbach, Wayne W.

    1995-01-01

    Loudspeakers and related acoustic transducers of improved type feature both light weight and energy efficiency of piezoelectric transducers and mechanical coupling efficiency. Active component of transducer made from wafer of "rainbow" piezoelectric material, ceramic piezoelectric material chemically reduced on one face. Chemical treatment forms wafer into dishlike shallow section of sphere. Both faces then coated with electrically conductive surface layers serving as electrodes. Applications include high-fidelity loudspeakers, and underwater echo ranging devices.

  11. Sphere-Wall Impact Experiments with Piezoelectric Force Sensors

    SciTech Connect

    Sinko, John E.; Lassiter, Jonathan S.

    2008-04-28

    Measurement of impulse imparted to a target from {mu}s-timescale laser ablation events is often performed with piezoelectric force sensors. For pulsed laser ablation with a target resting on the force sensors, an effect can occur for a vertical thrust stand in an exhaust-up configuration that results in measurement of about twice the actual imparted impulse. A CO{sub 2} laser operating at 10.6 {mu}m wavelength, 300 ns pulse length, and up to 20 J pulse energy single shots was used to ablate samples of PCTFE. Force sensor measurements of the imparted impulse were compared to tests with a ballistic pendulum over a variety of fluences. The theoretical impulse delivered by the impacts of 6 mm diameter spheres of aluminum, steel, POM, and PTFE on the force sensor were studied, and the coefficients of restitution were measured for the targets. Practical issues for measurement of ablation-imparted impulse with piezoelectric sensors are discussed.

  12. Piezoelectric dosimeter charger

    SciTech Connect

    Kronenberg, S.

    1981-01-27

    Disclosed is a small portable extremely rugged charger for existing pocket-sized type radiation dosimeters. The charger is comprised of a rectangularly shaped housing which contains a piezoelectric charging circuit which is manually operated by a handle to produce a relatively high charging voltage. The charging voltage is coupled to a charging post mounted on a removable cover which is adapted to be selectively rotated so that the underside of the charging post is exposed to light from one of two light windows in the housing whereupon the dosimeter scale may be viewed by either direct or reflected light from any source available. The piezoelectric charging circuit is comprised of a pair of axially aligned cylinders of piezoelectric material mounted in a fulcrum type frame having a beam lever element in contact with one of the cylinders. A spring bias element is connected to the beam lever element and is actuated by a cam attached to the handle which when rotated acts upon the spring to cause an axial compressional force to be applied to the cylinders which thereby produce the required charging voltage.

  13. Piezoelectric wind turbine

    NASA Astrophysics Data System (ADS)

    Kishore, Ravi Anant; Priya, Shashank

    2013-03-01

    In past few years, there has been significant focus towards developing small scale renewable energy based power sources for powering wireless sensor nodes in remote locations such as highways and bridges to conduct continuous health monitoring. These prior efforts have led to the development of micro-scale solar modules, hydrogen fuel cells and various vibration based energy harvesters. However, the cost effectiveness, reliability, and practicality of these solutions remain a concern. Harvesting the wind energy using micro-to-small scale wind turbines can be an excellent solution in variety of outdoor scenarios provided they can operate at few miles per hour of wind speed. The conventional electromagnetic generator used in the wind mills always has some cogging torque which restricts their operation above certain cut-in wind speed. This study aims to develop a novel piezoelectric wind turbine that utilizes bimorph actuators for electro-mechanical energy conversion. This device utilizes a Savonius rotor that is connected to a disk having magnets at the periphery. The piezoelectric actuators arranged circumferentially around the disk also have magnets at the tip which interacts with the magnetic field of the rotating disk and produces cyclical deflection. The wind tunnel experiments were conducted between 2-12 mph of wind speeds to characterize and optimize the power output of the wind turbine. Further, testing was conducted in the open environment to quantify the response to random wind gusts. An attempt was made towards integration of the piezoelectric wind turbine with the wireless sensor node.

  14. The Determination of Pesticidal and Non-Pesticidal Organotin Compounds by in situ Ethylation and Capillary Gas Chromatography with Pulsed Flame Photometric Detection

    EPA Science Inventory

    The concurrent determination of pesticidal and non-pesticidal organotin compounds in several water matrices, using a simultaneous in situ ethylation and liquid-liquid extraction followed by splitless injection mode capillary gas chromatography with pulsed flame photometric detect...

  15. The Determination of Pesticidal and Non-Pesticidal Organotin Compounds in Water Matrices by in situ Ethylation and Gas Chromatography with Pulsed Flame Photometric Detection

    EPA Science Inventory

    The concurrent determination of pesticidal and non-pesticidal organotin compounds in several water matrices, using a simultaneous in situ ethylation and liquid-liquid extraction followed by splitless injection mode capillary gas chromatography with pulsed flame photometric detect...

  16. Modelling the interaction between the plasma and the neutral gas in a pulsed glow discharge in nitrogen

    SciTech Connect

    Guiberteau, E.; Bonhomme, G.; Zoheir, C.

    1995-12-31

    We present here the first results obtained from the modelling of a pulsed glow discharge in nitrogen, taking into account the heat transfer to the neutral gas. The aim of modelling is to optimize the plasma process in a nitriding reactor. The iron sample to be nitrided forms the cathode of the glow discharge at low pressure (100 to 200 Pa). The reactor uses two disks of diameter 50 mm as electrodes with a 40 mm gap. It works in a pulsed regime (cycle period varies from 10 to 100 ms) with a discharge duration which can be varied from 0.5 to 10 ms. Experimental studies have been carried out using emission spectroscopy resolved in space (1 mm) and time (1 {mu}s), under various discharge and post-discharge durations. These studies have shown the important effect of energy transfer from the discharge to the neutral gas. In fact this transfer produces an expansion of the negative glow observed when the post-discharge duration is decreased. A realistic modelling should thus be performed bearing in mind that the neutral gas behaves not as a thermostat. Consequently the thermal and hydrodynamic evolution of the neutral gas must be considered in the whole modelling.

  17. CFD assisted simulation of temperature distribution and laser power in pulsed and CW pumped static gas DPALs

    NASA Astrophysics Data System (ADS)

    Waichman, Karol; Barmashenko, Boris D.; Rosenwaks, Salman

    2015-10-01

    An analysis of radiation, kinetic and fluid dynamic processes in diode pumped alkali lasers (DPALs) is reported. The analysis is based on a three-dimensional, time-dependent computational fluid dynamics (3D CFD) model. The CFD code which solves the gas conservation equations includes effects of natural convection and temperature diffusion of the species in the DPAL mixture. The gas flow conservation equations are coupled to the equations for DPAL kinetics and to the Beer-Lambert equations for pump and laser beams propagation. The DPAL kinetic processes in the Cs/CH4 (K/He) gas mixtures considered involve the three low energy levels, (1) n2S1/2, (2) n2P3/2 and (3) n2P1/2 (where n=4,6 for K and Cs, respectively), three excited alkali states and two alkali ionic states. Using the CFD model, the gas flow pattern and spatial distributions of the pump and laser intensities in the resonator were calculated for end-pumped CW and pulsed Cs and K DPALs. The DPAL power and medium temperature were calculated as a function of pump power and pump pulse duration. The CFD model results were compared to experimental results of Cs and K DPALs.

  18. Hybrid piezoelectric energy harvesting transducer system

    NASA Technical Reports Server (NTRS)

    Xu, Tian-Bing (Inventor); Jiang, Xiaoning (Inventor); Su, Ji (Inventor); Rehrig, Paul W. (Inventor); Hackenberger, Wesley S. (Inventor)

    2008-01-01

    A hybrid piezoelectric energy harvesting transducer system includes: (a) first and second symmetric, pre-curved piezoelectric elements mounted separately on a frame so that their concave major surfaces are positioned opposite to each other; and (b) a linear piezoelectric element mounted separately on the frame and positioned between the pre-curved piezoelectric elements. The pre-curved piezoelectric elements and the linear piezoelectric element are spaced from one another and communicate with energy harvesting circuitry having contact points on the frame. The hybrid piezoelectric energy harvesting transducer system has a higher electromechanical energy conversion efficiency than any known piezoelectric transducer.

  19. Nitriding molybdenum: Effects of duration and fill gas pressure when using 100-Hz pulse DC discharge technique

    NASA Astrophysics Data System (ADS)

    Ikhlaq, U.; R., Ahmad; Shafiq, M.; Saleem, S.; S. Shah, M.; Hussain, T.; A. Khan, I.; K., Abbas; S. Abbas, M.

    2014-10-01

    Molybdenum is nitrided by a 100-Hz pulsed DC glow discharge technique for various time durations and fill gas pressures to study the effects on the surface properties of molybdenum. X-ray diffractometry (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM) are used for the structural and morphological analysis of the nitrided layers. Vickers' microhardness tester is utilized to investigate surface microhardness. Phase analysis shows the formation of more molybdenum nitride molecules for longer nitriding durations at fill gas pressures of 2 mbar and 3 mbar (1 bar = 105 Pa). A considerable increase in surface microhardness (approximately by a factor of 2) is observed for longer duration (10 h) and 2-mbar pressure. Longer duration (10 h) and 2-mbar fill gas pressure favors the formation of homogeneous, smooth, hard layers by the incorporation of more nitrogen.

  20. Two-dimensional time-dependent modelling of fume formation in a pulsed gas metal arc welding process

    NASA Astrophysics Data System (ADS)

    Boselli, M.; Colombo, V.; Ghedini, E.; Gherardi, M.; Sanibondi, P.

    2013-06-01

    Fume formation in a pulsed gas metal arc welding (GMAW) process is investigated by coupling a time-dependent axi-symmetric two-dimensional model, which takes into account both droplet detachment and production of metal vapour, with a model for fume formation and transport based on the method of moments for the solution of the aerosol general dynamic equation. We report simulative results of a pulsed process (peak current = 350 A, background current 30 A, period = 9 ms) for a 1 mm diameter iron wire, with Ar shielding gas. Results showed that metal vapour production occurs mainly at the wire tip, whereas fume formation is concentrated in the fringes of the arc in the spatial region close to the workpiece, where metal vapours are transported by convection. The proposed modelling approach allows time-dependent tracking of fumes also in plasma processes where temperature-time variations occur faster than nanoparticle transport from the nucleation region to the surrounding atmosphere, as is the case for most pulsed GMAW processes.

  1. Diaphragm Pump With Resonant Piezoelectric Drive

    NASA Technical Reports Server (NTRS)

    Izenson, Michael G.; Kline-Schoder, Robert J.; Shimko, Martin A.

    2007-01-01

    A diaphragm pump driven by a piezoelectric actuator is undergoing development. This pump is intended to be a prototype of lightweight, highly reliable pumps for circulating cooling liquids in protective garments and high-power electronic circuits, and perhaps for some medical applications. The pump would be highly reliable because it would contain no sliding seals or bearings that could wear, the only parts subject to wear would be two check valves, and the diaphragm and other flexing parts could be designed, by use of proven methods, for extremely long life. Because the pump would be capable of a large volumetric flow rate and would have only a small dead volume, its operation would not be disrupted by ingestion of gas, and it could be started reliably under all conditions. The prior art includes a number piezoelectrically actuated diaphragm pumps. Because of the smallness of the motions of piezoelectric actuators (typical maximum strains only about 0.001), the volumetric flow rates of those pumps are much too small for typical cooling applications. In the pump now undergoing development, mechanical resonance would be utilized to amplify the motion generated by the piezoelectric actuator and thereby multiply the volumetric flow rate. The prime mover in this pump would be a stack of piezoelectric ceramic actuators, one end of which would be connected to a spring that would be part of a spring-and-mass resonator structure. The mass part of the resonator structure would include the pump diaphragm (see Figure 1). Contraction of the spring would draw the diaphragm to the left, causing the volume of the fluid chamber to increase and thereby causing fluid to flow into the chamber. Subsequent expansion of the spring would push the diaphragm to the right, causing the volume of the fluid chamber to decrease, and thereby expelling fluid from the chamber. The fluid would enter and leave the chamber through check valves. The piezoelectric stack would be driven electrically to

  2. High-Temperature Piezoelectric Ceramic Developed

    NASA Technical Reports Server (NTRS)

    Sayir, Ali; Farmer, Serene C.; Dynys, Frederick W.

    2005-01-01

    Active combustion control of spatial and temporal variations in the local fuel-to-air ratio is of considerable interest for suppressing combustion instabilities in lean gas turbine combustors and, thereby, achieving lower NOx levels. The actuator for fuel modulation in gas turbine combustors must meet several requirements: (1) bandwidth capability of 1000 Hz, (2) operating temperature compatible with the fuel temperature, which is in the vicinity of 400 F, (3) stroke of approximately 4 mils (100 m), and (4) force of 300 lb-force. Piezoelectric actuators offer the fastest response time (microsecond time constants) and can generate forces in excess of 2000 lb-force. The state-of-the-art piezoceramic material in industry today is Pb(Zr,Ti)O3, called PZT. This class of piezoelectric ceramic is currently used in diesel fuel injectors and in the development of high-response fuel modulation valves. PZT materials are generally limited to operating temperatures of 250 F, which is 150 F lower than the desired operating temperature for gas turbine combustor fuel-modulation injection valves. Thus, there is a clear need to increase the operating temperature range of piezoceramic devices for active combustion control in gas turbine engines.

  3. Generation of microwave-induced plasmas in automotive exhaust gas mixtures using pulsed microwave energy.

    PubMed

    Destefani, Carlos A; Siores, Elias; Murphy, Anthony B

    2003-01-01

    Microwave energy at 2.45 GHz was applied to a mixture of exhaust gases from a petrol engine at atmospheric pressure. It was found that by pulsing the microwave energy with a 50% duty cycle, the average power required to sustain a microwave-induced plasma discharge was decreased by about 40%. The ratio of absorbed to incident power was unaffected. These findings were confirmed for pulse frequencies from 10 to 300 Hz. PMID:15007864

  4. Simultaneous oxidation of NO, SO2 and Hg0 from flue gas by pulsed corona discharge.

    PubMed

    Xu, Fei; Luo, Zhongyang; Cao, Wei; Wang, Peng; Wei, Bo; Gao, Xiang; Fang, Mengxiang; Cen, Kefa

    2009-01-01

    A process capable of simultaneously oxidizing NO, SO2, and Hg0 was proposed, using a high-voltage and short-duration positive pulsed corona discharge. By focusing on NO, SO2, and Hg0 oxidation efficiencies, the influences of pulse peak voltage, pulse frequency, initial concentration, electrode number, residence time and water vapor addition were investigated. The results indicate that NO, SO2 and Hg0 oxidation efficiencies depend primarily on the radicals (OH, HO2, O) and the active species (O3, H2O2, etc.) produced by the pulsed corona discharge. The NO, SO2 and Hg0 oxidation efficiencies could be improved as pulse peak voltage, pulse frequency, electrode number and residence time increased, but they were reduced with increasing initial concentrations. By adding water vapor, the SO2 oxidation efficiency was improved remarkably, while the NO oxidation efficiency decreased slightly. In our experiments, the simultaneous NO, SO2, and Hg0 oxidation efficiencies reached to 40%, 98%, and 55% with the initial concentrations 479 mg/m3, 1040 mg/m3, and 15.0 microg/m3, respectively. PMID:19634444

  5. Acoustic experimental investigation of interaction femtosecond laser pulses with gas-aerosol media and biological tissues

    NASA Astrophysics Data System (ADS)

    Bochkarev, N. N.; Kabanov, A. M.; Stepanov, A. N.

    2008-02-01

    Using two optical acoustic approaches we experimentally investigated spatial location of filament zone of propagation channel of focused laser radiation. For femtosecond pulses passing in air it was shown that nonlinear focus length had spatial scale of 1/P at initial power P moderate for self-focusing and at optical system focus distance significantly lower than Rayleigh beam length. The results of experimental optical acoustic investigation of femto- and nanosecond pulses attenuation by some biological tissues (muscular tissue, adipose tissue, cutaneous covering, milk) and optical breakdown thresholds on these one are presented. It was shown that penetration depth of short laser pulse radiation into biological tissues is the same as for longer one. However, amplitude of acoustic response to a process of interaction of femtosecond laser pulse with biological tissue is larger in several times than that to interaction with nanosecond pulses of the same power and spectral distribution. The obtained of threshold values can be interesting for tabulation of limit allowable levels of irradiation at work with laser radiation. Such values are unknown for femtosecond laser pulses today.

  6. Variable gas leak rate valve

    DOEpatents

    Eernisse, Errol P.; Peterson, Gary D.

    1976-01-01

    A variable gas leak rate valve which utilizes a poled piezoelectric element to control opening and closing of the valve. The gas flow may be around a cylindrical rod with a tubular piezoelectric member encircling the rod for seating thereagainst to block passage of gas and for reopening thereof upon application of suitable electrical fields.

  7. Steady Secondary Flows Generated by Periodic Compression and Expansion of an Ideal Gas in a Pulse Tube

    NASA Technical Reports Server (NTRS)

    Lee, Jeffrey M.

    1999-01-01

    This study establishes a consistent set of differential equations for use in describing the steady secondary flows generated by periodic compression and expansion of an ideal gas in pulse tubes. Also considered is heat transfer between the gas and the tube wall of finite thickness. A small-amplitude series expansion solution in the inverse Strouhal number is proposed for the two-dimensional axisymmetric mass, momentum and energy equations. The anelastic approach applies when shock and acoustic energies are small compared with the energy needed to compress and expand the gas. An analytic solution to the ordered series is obtained in the strong temperature limit where the zeroth-order temperature is constant. The solution shows steady velocities increase linearly for small Valensi number and can be of order I for large Valensi number. A conversion of steady work flow to heat flow occurs whenever temperature, velocity or phase angle gradients are present. Steady enthalpy flow is reduced by heat transfer and is scaled by the Prandtl times Valensi numbers. Particle velocities from a smoke-wire experiment were compared with predictions for the basic and orifice pulse tube configurations. The theory accurately predicted the observed steady streaming.

  8. Semiconductor nanocrystallite formation using inert gas ambient pulsed laser ablation and its application to light-emitting devices

    NASA Astrophysics Data System (ADS)

    Yoshida, Takehito; Yamada, Yuka; Suzuki, Nobuyasu; Makino, Toshiharu; Orii, Takaaki; Onai, Seinosuke

    1999-07-01

    Pulsed laser ablation (PLA) in inert background gases can synthesize the nanoscaled silicon (Si), for studying its material properties as one of the quantum confinement effects. We report an optimized condition in Si nanocrystalline formation by the PLA in inert background gas, varying processing parameters: pulse energy and width, inert background gas pressure. The optimized process can prepare well-dispersed Si nanocrystallites without any droplets and debris. Furthermore, we investigate the influence of the processing parameters Si nanocrystallites without any droplets and debris. Furthermore, we investigate the influence of the processing parameters on transition from amorphous-like Si thin films to nanocrystallites. It was found that there is a processing window of the inert background gas pressure where the carrier confinement effects become apparent. Next, we have fabricated electroluminescent (EL), diodes with active layers of the Si nanocrystallites. The structure of the EL diodes was semitransparent platinum electrode/Si nanocrystallite layer/p-type Si/Pt electrode. We have observed visible spectra of not only green photoluminescence, but also red EL, at room temperature. Furthermore, we have found that the EL diodes showed strong nonlinear dependence of EL intensity on current density.

  9. A Piezoelectric Shear Stress Sensor

    NASA Technical Reports Server (NTRS)

    Kim, Taeyang; Saini, Aditya; Kim, Jinwook; Gopalarathnam, Ashok; Zhu, Yong; Palmieri, Frank L.; Wohl, Christopher J.; Jiang, Xiaoning

    2016-01-01

    In this paper, a piezoelectric sensor with a floating element was developed for shear stress measurement. The piezoelectric sensor was designed to detect the pure shear stress suppressing effects of normal stress generated from the vortex lift-up by applying opposite poling vectors to the: piezoelectric elements. The sensor was first calibrated in the lab by applying shear forces and it showed high sensitivity to shear stress (=91.3 +/- 2.1 pC/Pa) due to the high piezoelectric coefficients of PMN-33%PT (d31=-1330 pC/N). The sensor also showed almost no sensitivity to normal stress (less than 1.2 pC/Pa) because of the electromechanical symmetry of the device. The usable frequency range of the sensor is 0-800 Hz. Keywords: Piezoelectric sensor, shear stress, floating element, electromechanical symmetry

  10. Glory of piezoelectric perovskites

    NASA Astrophysics Data System (ADS)

    Uchino, Kenji

    2015-08-01

    This article reviews the history of piezoelectric perovskites and forecasts future development trends, including Uchino’s discoveries such as the Pb(Mg1/3Nb2/3)O3-PbTiO3 electrostrictor, Pb(Zn1/3Nb2/3)O3-PbTiO3 single crystal, (Pb, La)(Zr, Ti)O3 photostriction, and Pb(Zr, Ti)O3-Terfenol magnetoelectric composites. We discuss five key trends in the development of piezomaterials: performance to reliability, hard to soft, macro to nano, homo to hetero, and single to multi-functional.