Science.gov

Sample records for rods impact

  1. Impact of AD995 alumina rods

    SciTech Connect

    Chhabildas, L.C.; Furnish, M.D.; Reinhart, W.D.; Grady, D.E.

    1997-10-01

    Gas guns and velocity interferometric techniques have been used to determine the loading behavior of an AD995 alumina rod 19 mm in diameter by 75 mm and 150 mm long, respectively. Graded-density materials were used to impact both bare and sleeved alumina rods while the velocity interferometer was used to monitor the axial-velocity of the free end of the rods. Results of these experiments demonstrate that (1) a time-dependent stress pulse generated during impact allows an efficient transition from the initial uniaxial strain loading to a uniaxial stress state as the stress pulse propagates through the rod, and (2) the intermediate loading rates obtained in this configuration lie between split Hopkinson bar and shock-loading techniques.

  2. Fragmentation of an axially impacted slender rod

    NASA Astrophysics Data System (ADS)

    Ji, W.; Waas, A. M.

    2010-02-01

    Motivated by experimental results on the dynamic buckling and fragmentation of a vertical column impacted by a falling mass, results from an analytical model for dynamic buckling which considers the dynamic interaction between the axial column deformation and the out-of-plane buckling displacements are used to interpret the fragmentation process and the resulting fragment lengths. It is shown that a critical time exists for the rod to undergo fragmentation. At this critical time, the rod deforms in a modulated pattern of waves, setting up the stage for the ensuing fragmentation as a result of induced large curvatures that exceed the critical bending strain of the rod material. The resulting fragment length distributions, which show two characteristics peaks at \\frac{\\lambda}{2} and \\frac{\\lambda}{4} , where λ is a characteristic half-wavelength, are found to compare favorably with the experimental results.

  3. Dynamic, multiaxial impact response of confined and unconfined ceramic rods

    SciTech Connect

    Wise, J.L.; Grady, D.E.

    1993-09-01

    A new configuration for impact testing was implemented which yielded time-resolved measurements of the dynamic response of materials undergoing multiaxial strain. With this`-Method, one end of an initially stationary rod (ie., right circular cylinder) of test material was subjected to planar impact with a flat-faced projectile. The test rod was either free (unconfined) or mounted within a close-fitting sleeve which provided lateral confinement. Velocity interferometer diagnostics monitored the axial (longitudinal) velocity of the rod free end, and the transverse (radial) velocity for one or more points on the periphery of the rod or confinement sleeve. Analysis of the resultant velocity records allowed assessment of material properties, such as wave speeds and compressive yield strength, without the requirement of intact recovery of the rod. Data were obtained for alumina (Coors AD-99.5) rods in a series of tests involving variations in confinement and peak impact stress.

  4. Transient elastic impact response of slender graphite rods

    SciTech Connect

    Erdem, I.

    2007-12-15

    Graphite rods are manufactured by extruding the mixture of calcined petroleum coke and coal tar pitch into the desired shape and baking the cooled specimens at about 800{sup o}C. Cracking can occur in rods during the manufacturing process. It is useful to be able to detect the presence of such cracks in the rods prior to their being machined and put into use as electrodes or cathodes or thermal insulator. In an effort to develop a nondestructive testing approach to evaluation of the rods, transient elastic impact was determined for slender rods. Theory for solid, slender rods provided an important starting point for this work. Subsequently, numerical models were developed and simulation was used to determine the response of rods containing cracks. Experiments on graphite rods with and without cracks were conducted and the internal condition determined from the recorded signals. The rods were then cut lengthwise to reveal the internal condition and verify the predicted results. In all cases the knowledge gained from simulation allowed for the presence of cracks to be detected.

  5. Failure kinetics in borosilicate glass during rod impact

    SciTech Connect

    Orphal, Dennis L.; Anderson, Charles E. Jr.; Behner, Thilo; Hohler, Volker; Wickert, Matthias; Templeton, Douglas W.

    2007-12-12

    Failure front (FF) and penetration velocity have been measured for long gold rods impacting and penetrating borosilicate (BS) glass. Data are obtained by visualizing simultaneously FF propagation with a high speed camera and rod penetration with flash X-rays. Results for BS glass are qualitatively similar to those of DEDF (PbO) glass. FF velocity rapidly decreases from an initial value to a lower, approximately constant value. FF velocity increases with impact velocity, v{sub p}. The FF velocity remains significantly lower than the shear velocity, even at the highest impact velocity tested, about 2.5 km/s. The ratio of the FF velocity to the rod penetration velocity, v{sub F}/u, decreases with increasing v{sub p} and appears to be approaching v{sub F}/u = 1 asymptotically, as observed previously for DEDF glass. The separation of the FF and the tip of the rod decreases with increasing impact velocity. Importantly, since v{sub F}/u{>=}1, the gold rod is always penetrating glass behind the FF.

  6. Additional information for impact response of the restart safety rods

    SciTech Connect

    Yau, W.W.F.

    1991-10-14

    WSRC-RP-91-677 studied the structural response of the safety rods under the conditions of brake failure and accidental release. It was concluded that the maximum impact loading to the safety rod is 6020 pounds based on conservative considerations that energy dissipation attributable to fluid resistance and reactor superstructure flexibility. The staffers of the Defense Nuclear Facility Safety Board reviewed the results and inquired about the extent of conservatism. By request of the RESTART team, I reassessed the impact force due to these conservative assumptions. This memorandum reports these assessments.

  7. COST IMPACT OF ROD CONSOLIDATION ON THE VIABILITY ASSESSMENT DESIGN

    SciTech Connect

    D. Lancaster

    1999-03-29

    The cost impact to the Civilian Radioactive Waste Management System of using rod consolidation is evaluated. Previous work has demonstrated that the fuel rods of two assemblies can be packed into a canister that can fit into the same size space as that used to store a single assembly. The remaining fuel assembly hardware can be compacted into the same size canisters with a ratio of 1 hardware canister per each 6 to 12 assemblies. Transportation casks of the same size as currently available can load twice the number of assemblies by placing the compacted assemblies in the slots currently designed for a single assembly. Waste packages similarly could contain twice the number of assemblies; however, thermal constraints would require considering either a low burnup or cooling. The analysis evaluates the impact of rod consolidation on CRWMS costs for consolidation at prior to transportation and for consolidation at the Monitored Geological Repository surface facility. For this study, no design changes were made to either the transport casks or waste packages. Waste package designs used for the Viability Assessment design were employed but derated to make the thermal limits. A logistics analysis of the waste was performed to determine the number of each waste package with each loading. A review of past rod consolidation experience found cost estimates which range from $10/kgU to $32/kgU. $30/kgU was assumed for rod consolidation costs prior to transportation. Transportation cost savings are about $17/kgU and waste package cost savings are about $21/kgU. The net saving to the system is approximately $500 million if the consolidation is performed prior to transportation. If consolidation were performed at the repository surface facilities, it would cost approximately $15/kgU. No transportation savings would be realized. The net savings for consolidation at the repository site would be about $400 million dollars.

  8. Grid-to-rod flow-induced impact study for PWR fuel in reactor

    DOE PAGESBeta

    Jiang, Hao; Qu, Jun; Lu, Roger Y.; Wang, Jy-An John

    2016-06-10

    The source for grid-to-rod fretting in a pressurized water nuclear reactor (PWR) is the dynamic contact impact from hydraulic flow-induced fuel assembly vibration. In order to support grid-to-rod fretting wear mitigation research, finite element analysis (FEA) was used to evaluate the hydraulic flow-induced impact intensity between the fuel rods and the spacer grids. Three-dimensional FEA models, with detailed geometries of the dimple and spring of the actual spacer grids along with fuel rods, were developed for flow impact simulation. The grid-to-rod dynamic impact simulation provided insights of the contact phenomena at grid-rod interface. Finally, it is an essential and effectivemore » way to evaluate contact forces and provide guidance for simulative bench fretting-impact tests.« less

  9. Failure of expansion joint tie rods -- Impact on bellows integrity

    SciTech Connect

    Daugherty, W.L.; Miller, R.F.

    1992-01-01

    Expansion joints are used in piping systems to accomodate pipe deflections during service and to facilitate fitup. Often, tie rods are employed to limit the range of axial deflection. Additional restraint against excessive displacement can be provided by the surrounding pipe and associated supports. This paper presents a methodology that was employed to estimate the consequences of tie rod failure. Of particular interest is whether tie rod failure can lead to sufficient displacement as to cause bellows rupture.

  10. Failure of expansion joint tie rods -- Impact on bellows integrity

    SciTech Connect

    Daugherty, W.L.; Miller, R.F.

    1992-12-31

    Expansion joints are used in piping systems to accomodate pipe deflections during service and to facilitate fitup. Often, tie rods are employed to limit the range of axial deflection. Additional restraint against excessive displacement can be provided by the surrounding pipe and associated supports. This paper presents a methodology that was employed to estimate the consequences of tie rod failure. Of particular interest is whether tie rod failure can lead to sufficient displacement as to cause bellows rupture.

  11. Calculated concrete target damage by multiple rod impact and penetration

    SciTech Connect

    Pincosy, P A; Murphy, M J

    2006-12-29

    The effect of enhanced crater formation has been demonstrated experimentally when multiple and delayed shaped charge jets impact and penetrate concrete. The concept for enhancement utilizes a single follow-on jet at the centerline of holes produced by multiple precursor jets penetrating the surrounding the region. Calculations of the 3D crater enhancement phenomena have been conducted with multiple rods to simulate the steady state portion of the multiple jet penetration process. It is expected that this analysis methodology will be beneficial for optimization of the multiple jet crater enhancement application. We present calculated results using ALE3D where the model uses the standard Gruneisen equation of state combined with a rate dependent strength model including material damage parameters. This study focuses on the concrete material damage model as a representation of the portion of the target that would eventually be ejected creating a large bore-hole. The calculations are compared with the experimental evidence and limitations of the modeling approach are discussed.

  12. Failure and penetration response of borosilicate glass during short-rod impact

    SciTech Connect

    Anderson, C. E. Jr.; Orphal, D. L.; Behner, Th.; Hohler, V.; Wickert, M.; Templeton, D. W.

    2007-12-12

    The failure characterization of brittle materials like glass is of fundamental importance in describing the penetration resistance against projectiles. A critical question is whether this failure front remains 'steady' after the driving stress is removed. A test series with short gold rods (D = 1 mm, L/D{approx_equal}5-11) impacting borosilicate glass at {approx}1 to 2 km/s was carried out to investigate this question. The reverse ballistic method was used for the experiments, and the impact and penetration process was observed simultaneously with five flash X-rays and a 16-frame high-speed optical camera. Very high measurement accuracy was established to ensure reliable results. Results show that the failure front induced by rod impact and penetration does arrest (ceases to propagate) after the rod is totally eroded inside the glass. The impact of a second rod after a short time delay reinitiates the failure front at about the same speed.

  13. Impact Initiation of Rods of Pressed Polytetrafluoroethylene (PTFE) and Aluminum Powders

    SciTech Connect

    Mock, Willis Jr.; Holt, William H.

    2006-07-28

    A gas gun has been used to investigate the shock initiation of rods of a mixture of 74 wt% PTFE and 26 wt% aluminum powders. The rods were sabot-launched into 4340 steel anvils at impact velocities ranging from 104 to 963 m/s. A framing camera was used to observe the time sequence of events. At low velocity, no initiation occurred. Above an initiation threshold, the initiation time dropped abruptly from 56 {mu}s just above threshold to 4 {mu}s at the highest impact velocity. Several high velocity experiments were performed for pure PTFE material for comparison with the PTFE/Al rods.

  14. Failure Wave in DEDF and Soda-Lime Glass During Rod Impact

    NASA Astrophysics Data System (ADS)

    Orphal, Dennis; Behner, Thilo; Anderson, Charles; Templeton, Douglas

    2005-07-01

    Investigations of glass by planar, and classical and symmetric Taylor impact experiments reveal that failure wave velocity U/F depends on impact velocity, geometry, and the type of glass. U/F typically increases with impact velocity to between ˜ 1.4 C/S and C/L (shear and longitudinal wave velocities, respectively). This paper reports the results of direct high-speed photographic measurements of the failure wave for gold rod impact from 1.2 and 2.0 km/s on DEDF glass (C/S = 2.0, C/L =3.5 km/s). The average rod penetration velocity, u, was measured using flash X-rays. Gold rods eliminated penetrator strength effects. U/F for gold rod impact on DEDF is ˜ 1.0-1.2 km/s, which is considerably less than C/S. The increase of u with impact velocity is greater than that of U/F. These results are confirmed by soda-lime glass impact on a gold rod at an impact velocity of 1300 m/s. Similar results are found in``edge-on-impact'' tests; U/F values of 1.4 km/s and 2.4-2.6 km/s in soda-lime glass are reported for W-alloy rod impact, considerably less than C/S (3.2 km/s) [1,2]. [1] Bless, et. al.(1990) AIP Proc. Shock Comp. Cond. Matter---1989, pp. 939-942 (1990) [2] E. L. Zilberbrand, et. al. (1999) Int. J. Impact Engng., 23, 995-1001 (1999).

  15. Optimal resistance in impact and penetration of parallel rods in a granular medium

    NASA Astrophysics Data System (ADS)

    Ding, Yang; London, Lionel; Garcia, Mateo; Goldman, Daniel

    2007-11-01

    Inspired by foot and toe morphology in sand-running lizards, we study in laboratory experiment and experimentally validated Molecular Dynamics (MD) simulation the resistance force during penetration of parallel rods (diameter 1.27 cm) into a granular medium of plastic spheres (diameter d=0.6 mm) as a function of rod separation l. We measure the normal force exerted on the rods by the medium both during normal penetration at constant velocity ( 10 cm/sec) and during normal impact after freefall (impact velocity 2.5 m/sec). For constant velocity penetration, the resistance force increases linearly with increasing penetration depth. The slope of this curve (force/depth) displays a maximum as a function of l at l 1.6d. In the impact studies, we observe a maximum in the collision force at l 1.6d and a minimum in penetration depth at l 2d. The extrema are correlated with an increase in lateral force between the rods indicating that jammed grains increase the effective surface area during penetration.

  16. Failure Wave in DEDF and Soda-Lime Glass during Rod Impact

    SciTech Connect

    Orphal, D. L.; Behner, Th.; Hohler, V.; Anderson, C. E. Jr.; Templeton, D. W.

    2006-07-28

    Investigations of glass by planar, and classical and symmetric Taylor impact experiments reveal that failure wave velocity vF depends on impact velocity, geometry, and type of glass. vF typically increases with impact velocity vP to between cS and cL or to {radical}2cS (shear and longitudinal wave velocity). This paper reports initial results of an investigation of failure waves associated with gold rod impact on high-density (DEDF) glass and soda-lime glass. Data are obtained by visualizing simultaneously the failure propagation in the glass with a high-speed camera and the rod penetration velocity u with flash radiography. Results for DEDF glass are reported for vP between 1.2 and 2.0 km/s, those for soda-lime glass with vP {approx_equal}1.3 km/s. It is shown that vF > u, and that in the case of DEDF glass vF/u decreases from ; 1.38 to 1.13 with increasing vp. In addition, several Taylor tests were performed. For both DEDF and soda-lime glass the vF-values, found here as well as vF- data reported in the literature, reveal that--for equal pressures--the failure wave velocities determined from Taylor tests or planar-impact tests are distinctly greater than those observed during steady-state rod penetration.

  17. Contact-coupled impact of slender rods: analysis and experimental validation.

    PubMed

    Tibbitts, Ira B; Kakarla, Deepika; Siskey, Stephanie; Ochoa, Jorge A; Ong, Kevin L; Brannon, Rebecca M

    2014-02-01

    To validate models of contact mechanics in low speed structural impact, slender rods were impacted in a drop tower, and measurements of the contact and vibration were compared to analytical and finite element (FE) models. The contact area was recorded using a novel thin-film transfer technique, and the contact duration was measured using electrical continuity. Strain gages recorded the vibratory strain in one rod, and a laser Doppler vibrometer measured speed. The experiment was modeled analytically on a one-dimensional spatial domain using a quasi-static Hertzian contact law and a system of delay differential equations. The three-dimensional FE model used hexahedral elements, a penalty contact algorithm, and explicit time integration. A small submodel taken from the initial global FE model economically refined the analysis in the small contact region. Measured contact areas were within 6% of both models' predictions, peak speeds within 2%, cyclic strains within 12 με (RMS value), and contact durations within 2 μs. The global FE model and the measurements revealed small disturbances, not predicted by the analytical model, believed to be caused by interactions of the non-planar stress wavefront with the rod's ends. The accuracy of the predictions for this simple test, as well as the versatility of the diagnostic tools, validates the theoretical and computational models, corroborates instrument calibration, and establishes confidence that the same methods may be used in experimental and computational study of contact mechanics during impact of more complicated structures. Recommendations are made for applying the methods to a particular biomechanical problem: the edge-loading of a loose prosthetic hip joint which can lead to premature wear and prosthesis failure. PMID:24729630

  18. An explanation for the anomalous wave profiles obtained in Composition B-3 impacted by flat nosed steel rods

    NASA Astrophysics Data System (ADS)

    James, Hugh; Gustavsen, Richard; Dattelbaum, Dana

    2015-06-01

    When firing flat nosed steel rods into the 60/40 RDX/TNT explosive Composition B-3, Gustavsen et al. (``Initiation of Composition B-3 by impact of flat nosed rods,'' in 15th Int. Det. Symp.) found an apparently anomalous ``hump'' in particle velocity wave profiles. The hump occurred on the center-line established by the rod, and at relatively late times, > 1 μs, after detonation onset. Several explanations, including that of a late time reaction, were postulated. This report will present evidence that the anomalous late time ``hump'' is due to the arrival of rarefaction waves from the rod periphery. Simple analytic calculations and reactive-burn hydro-code calculations will be presented supporting this hypothesis.

  19. Contact-coupled impact of slender rods: analysis and experimental validation

    PubMed Central

    Tibbitts, Ira B.; Kakarla, Deepika; Siskey, Stephanie; Ochoa, Jorge A.; Ong, Kevin L.; Brannon, Rebecca M.

    2013-01-01

    To validate models of contact mechanics in low speed structural impact, slender rods were impacted in a drop tower, and measurements of the contact and vibration were compared to analytical and finite element (FE) models. The contact area was recorded using a novel thin-film transfer technique, and the contact duration was measured using electrical continuity. Strain gages recorded the vibratory strain in one rod, and a laser Doppler vibrometer measured speed. The experiment was modeled analytically on a one-dimensional spatial domain using a quasi-static Hertzian contact law and a system of delay differential equations. The three-dimensional FE model used hexahedral elements, a penalty contact algorithm, and explicit time integration. A small submodel taken from the initial global FE model economically refined the analysis in the small contact region. Measured contact areas were within 6% of both models’ predictions, peak speeds within 2%, cyclic strains within 12 με (RMS value), and contact durations within 2 μs. The global FE model and the measurements revealed small disturbances, not predicted by the analytical model, believed to be caused by interactions of the non-planar stress wavefront with the rod’s ends. The accuracy of the predictions for this simple test, as well as the versatility of the diagnostic tools, validates the theoretical and computational models, corroborates instrument calibration, and establishes confidence that the same methods may be used in experimental and computational study of contact mechanics during impact of more complicated structures. Recommendations are made for applying the methods to a particular biomechanical problem: the edge-loading of a loose prosthetic hip joint which can lead to premature wear and prosthesis failure. PMID:24729630

  20. 78 FR 58517 - Notice of Availability of the Record of Decision (ROD) and Finding of No Significant Impact...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-24

    ... Natural Resources Conservation Service Notice of Availability of the Record of Decision (ROD) and Finding of No Significant Impact (FONSI) for the Bayou Meto Basin Project, Arkansas AGENCY: Natural Resources... Natural Resources Conservation Service, Room 3416, Federal Building, 700 West Capitol Avenue, Little...

  1. Rodding Surgery

    MedlinePlus

    ... Rods can be made of stainless steel or titanium. Regular rods do not expand. They have many ... v regular), the rod materials (stainless steel v titanium) and the age for a first rodding surgery. ...

  2. The impact of tungsten long rod penetrators into water filled targets

    SciTech Connect

    Wilson, L.T.; Dickinson, D.L.; Hertel, E.S. Jr.

    1998-02-01

    Twelve experiments were conducted to determine the effect of water filled targets on the penetration of tungsten long rods in terms of their residual mass and integrity. CTH hydrocode calculations were performed for each of the experiments to ensure that the erosion and breakup of the tungsten projectiles could be accurately reproduced. The CTH hydrocode predictions correlation well with the experimental results in most cases. Only 8% of the variance is unexplained. The slip interface between the rod and water was approximated in one of two ways: (1) using the CTH BLINT option in 2-D or (2) using a standard Eulerian mixed cells treatment. Results indicate that a 3-D BLINT algorithm is critical to predicting rod residual lengths. The authors were unable to reproduce rod fracture that occurred in every experiment where the water column exceeded 25 cm in length. The authors feel that this is due to a change in rod material properties during penetration, and continue to investigate the issue.

  3. Instrumented Taylor anvil-on-rod impact tests for validating applicability of standard strength models to transient deformation states

    NASA Astrophysics Data System (ADS)

    Eakins, D. E.; Thadhani, N. N.

    2006-10-01

    Instrumented Taylor anvil-on-rod impact tests have been conducted on oxygen-free electronic copper to validate the accuracy of current strength models for predicting transient states during dynamic deformation events. The experiments coupled the use of high-speed digital photography to record the transient deformation states and laser interferometry to monitor the sample back (free surface) velocity as a measure of the elastic/plastic wave propagation through the sample length. Numerical continuum dynamics simulations of the impact and plastic wave propagation employing the Johnson-Cook [Proceedings of the Seventh International Symposium on Ballistics, 1983, The Netherlands (Am. Def. Prep. Assoc. (ADPA)), pp. 541-547], Zerilli-Armstrong [J. Appl. Phys. C1, 1816 (1987)], and Steinberg-Guinan [J. Appl. Phys. 51, 1498 (1980)] constitutive equations were used to generate transient deformation profiles and the free surface velocity traces. While these simulations showed good correlation with the measured free surface velocity traces and the final deformed sample shape, varying degrees of deviations were observed between the photographed and calculated specimen profiles at intermediate deformation states. The results illustrate the usefulness of the instrumented Taylor anvil-on-rod impact technique for validating constitutive equations that can describe the path-dependent deformation response and can therefore predict the transient and final deformation states.

  4. Use of Taylor Rod-on-Anvil Impact Experiments to Investigate High Strain Rate Behaviour in Polyolefins

    NASA Astrophysics Data System (ADS)

    Bucknall, David; Luce, Amanda; Kannan, Abhiram; Breidenich, Jennifer; Thadhani, Naresh

    2015-06-01

    The high strain rate deformation and mechano-lumination of various polyethylenes and polypropylene is studied using Taylor rod-on-anvil impact testing. Polypropylene and low density (LDPE), high density (HDPE), and ultra high molecular weight (UHMWPE) polyethylene samples were impacted against a hardened steel anvil at velocities ranging from 50-500 m/s. High-speed imaging, time-resolved spectroscopy, and thermal imaging are employed to track the macroscopic shape change and observe mechano-lumination and heating during impact. Additionally, electron spin resonance (ESR) and gel permeation chromatography (GPC) measurements were performed on recovered impacted samples to explain the observed deformation behavior in the various polyolefins. Time-resolved spectroscopy, coupled with ESR and GPC measurements indicate that chain scission occurs during the first few microseconds of the impact event. The observed macroscopic deformation that occurs after the observed mechano-illumination event is therefore influenced by the loss of mechanical strength associated with a drop in the molecular weight of the polymer.

  5. Divining the Impact on Education of an Australian Bill of Rights with and American Rod.

    ERIC Educational Resources Information Center

    Birch, I. K. F.

    1986-01-01

    Explores the common law-bill of rights debate in Australia and the probable impacts of extending constitutional and statutory rights to the educational system. Closely examined are compulsory education, the courts' role, children's rights, and the law and education interface, with reference to equality and quality issues in the United States.…

  6. 75 FR 30899 - Notice of a Finding of No Significant Impact (FONSI) and Record of Decision (ROD) on a Final...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-02

    ... Decision (ROD) on a Final Environmental Assessment (FEA) for the Proposed Federal Action at the Macon... FAA is issuing this notice to advise the public of the approval of a FONSI/ROD on an FEA for a... affect the quality of the environment. The FEA evaluated Macon County Airport's proposal to extend...

  7. Impact of axial compression and torque on strain localization and fracture under complex cyclic loading of Plexiglas rods

    NASA Astrophysics Data System (ADS)

    Karpov, E. V.; Larichkin, A. Yu.

    2014-01-01

    Experimental studies of deformation and fracture of rods made of Plexiglas (PMMA) under complex loading (quasi-static and cyclic torsion under axial compression) are performed. The existence of a range of critical values of axial stress, within which the rod is fractured by the torque, is established. The localization of "frozen" highly elastic strains in constrained cyclic torsion is revealed, and the conditions of its occurrence are determined. The effect of axial stress on strain localization and fracture and the influence of cyclic torsion on the loss of stability of a rod under axial compression are shown.

  8. CONTROL ROD

    DOEpatents

    Zinn, W.H.; Ross, H.V.

    1958-11-18

    A control rod is described for a nuclear reactor. In certaln reactor designs it becomes desirable to use a control rod having great width but relatively llttle thickness. This patent is addressed to such a need. The neutron absorbing material is inserted in a triangular tube, leaving volds between the circular insert and the corners of the triangular tube. The material is positioned within the tube by the use of dummy spacers to achleve the desired absorption pattern, then the ends of the tubes are sealed with suitable plugs. The tubes may be welded or soldered together to form two flat surfaces of any desired width, and covered with sheetmetal to protect the tubes from damage. This design provides a control member that will not distort under the action of outside forces or be ruptured by gases generated within the jacketed control member.

  9. Impact of the control rod consumption on the reactivity control of a SFR break-even core

    SciTech Connect

    Blanchet, D.; Fontaine, B.

    2012-07-01

    Current design studies on Sodium Fast Reactor (SFR) differ from those performed in the past by the fact that design criteria are now those of the Generation IV reactors. In order to improve their safety, reactors with break-even cores are preferred because they minimize the needs in terms of reactivity control and limit the consequences of control rod withdrawal. Furthermore, as the reactivity control needs are low, break-even core enables the use of absorbing materials with reduced efficiency (natural boron, hafnium...). Nevertheless, the use of control rods with few absorbing materials may present the disadvantage of a non-negligible ({approx}10%) loss of efficiency due to their consumption under irradiation. This paper presents a methodology to calculate accurately and analyze this consumption. (authors)

  10. 78 FR 58517 - Notice of Availability of the Record of Decision (ROD) and Findings of No Significant Impact...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-24

    ... of No Significant Impact (FONSI) for the Grand Prairie Area Demonstration Project AGENCY: Natural...) entitled: ``General Reevaluation Report and Environmental Impact Statement for the Grand Prairie...: ``Environmental Assessment Grand Prairie Area Demonstration Project, Post General Reevaluation Design...

  11. 32 CFR 989.21 - Record of decision (ROD).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... the signator. A ROD (40 CFR 1505.2) is a concise public document stating what an agency's decision is... ENVIRONMENTAL IMPACT ANALYSIS PROCESS (EIAP) § 989.21 Record of decision (ROD). (a) The proponent and the...

  12. 32 CFR 989.21 - Record of decision (ROD).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... the signator. A ROD (40 CFR 1505.2) is a concise public document stating what an agency's decision is... ENVIRONMENTAL IMPACT ANALYSIS PROCESS (EIAP) § 989.21 Record of decision (ROD). (a) The proponent and the...

  13. Rod examination gauge

    SciTech Connect

    Bacvinskas, W.S.; Bayer, J.E.; Davis, W.W.; Fodor, G.; Kikta, T.J.; Matchett, R.L.; Nilsen, R.J.; Wilczynski, R.

    1991-12-31

    The present invention is directed to a semi-automatic rod examination gauge for performing a large number of exacting measurements on radioactive fuel rods. The rod examination gauge performs various measurements underwater with remote controlled machinery of high reliability. The rod examination gauge includes instruments and a closed circuit television camera for measuring fuel rod length, free hanging bow measurement, diameter measurement, oxide thickness measurement, cladding defect examination, rod ovality measurement, wear mark depth and volume measurement, as well as visual examination. A control system is provided including a programmable logic controller and a computer for providing a programmed sequence of operations for the rod examination and collection of data.

  14. FUEL ROD ASSEMBLY

    DOEpatents

    Hutter, E.

    1959-09-01

    A cluster of nuclear fuel rods aod a tubular casing through which a coolant flows in heat-change contact with the ruel rods are described. The casting is of trefoil section and carries the fuel rods, each of which has two fin engaging the serrated fins of the other two fuel rods, whereby the fuel rods are held in the casing and are interlocked against relative longitudinal movement.

  15. Control rod drive

    SciTech Connect

    Hawke, Basil C.

    1986-01-01

    A control rod drive uses gravitational forces to insert one or more control rods upwardly into a reactor core from beneath the reactor core under emergency conditions. The preferred control rod drive includes a vertically movable weight and a mechanism operatively associating the weight with the control rod so that downward movement of the weight is translated into upward movement of the control rod. The preferred control rod drive further includes an electric motor for driving the control rods under normal conditions, an electrically actuated clutch which automatically disengages the motor during a power failure and a decelerator for bringing the control rod to a controlled stop when it is inserted under emergency conditions into a reactor core.

  16. Piston rod seal

    DOEpatents

    Lindskoug, Stefan

    1984-01-01

    In a piston rod seal of the type comprising a gland through which the piston rod is passed the piston is provided with a sleeve surrounding the piston rod and extending axially so as to axially partly overlap the gland when the piston is in its bottom dead center position.

  17. CONTROL ROD DRIVE

    DOEpatents

    Chapellier, R.A.; Rogers, I.

    1961-06-27

    Accurate and controlled drive for the control rod is from an electric motor. A hydraulic arrangement is provided to balance a piston against which a control rod is urged by the application of fluid pressure. The electric motor drive of the control rod for normal operation is made through the aforementioned piston. In the event scramming is required, the fluid pressure urging the control rod against the piston is relieved and an opposite fluid pressure is applied. The lack of mechanical connection between the electric motor and control rod facilitates the scramming operation.

  18. More on the penetration of yawed rods

    NASA Astrophysics Data System (ADS)

    Rosenberg, Z.; Dekel, E.; Ashuach, Y.

    2006-08-01

    One of the most complex processes, in the field of terminal ballistics, is that of yawed impact of long rods. In spite of many experimental observations, and some analytical modeling, a clear picture of this issue is still lacking. In order to gain some insight into the operating mechanisms, we developed a simple engineering model which considers the yawed rod as a series of small disks. We then define the effective length and diameter of the rod by considering those disks which are going to hit the initial crater which is opened by the impact. We also performed a series of 3D numerical simulations with various L/D tungsten alloy rods impacting a steel target, at yaws in the full range of 0-90^circ. We analyzed the results of these simulations in terms of the normalized penetration (P/D), where D is the rod diameter, and looked for systematic trends in the results for the various rods. The agreement between our model predictions and both experimental data and simulation results is quite good. Based on this agreement we can highlight some new features of the penetration process of yawed rods.

  19. CRUCIFORM CONTROL ROD JOINT

    DOEpatents

    Thorp, A.G. II

    1962-08-01

    An invention is described which relates to nuclear reactor control rod components and more particularly to a joint between cruciform control rod members and cruciform control rod follower members. In one embodiment this invention provides interfitting crossed arms at adjacent ends of a control rod and its follower in abutting relation. This holds the members against relative opposite longitudinal movement while a compression member keys the arms against relative opposite rotation around a common axis. Means are also provided for centering the control rod and its follower on a common axis and for selectively releasing the control rod from its follower for the insertion of a replacement of the control rod and reuse of the follower. (AEC)

  20. CONTROL ROD DRIVE

    DOEpatents

    Chapellier, R.A.

    1960-05-24

    BS>A drive mechanism was invented for the control rod of a nuclear reactor. Power is provided by an electric motor and an outside source of fluid pressure is utilized in conjunction with the fluid pressure within the reactor to balance the loadings on the motor. The force exerted on the drive mechanism in the direction of scramming the rod is derived from the reactor fluid pressure so that failure of the outside pressure source will cause prompt scramming of the rod.

  1. Pull rod assembly

    DOEpatents

    Cioletti, O.C.

    1988-04-21

    A pull rod assembly comprising a pull rod having three peripheral grooves, a piston device including an adaptor ring and a seal ring, said piston device being mounted on the pull rod by a split ring retainer situated in one groove and extending into an interior groove in the adaptor and a resilient split ring retained in another groove and positioned to engage the piston device and to retain the seal on its adaptor.

  2. FUEL ROD CLUSTERS

    DOEpatents

    Schultz, A.B.

    1959-08-01

    A cluster of nuclear fuel rods and a tubular casing therefor through which a coolant flows in heat-exchange contact with the fuel rods is described. The fuel rcds are held in the casing by virtue of the compressive force exerted between longitudinal ribs of the fuel rcds and internal ribs of the casing or the internal surfaces thereof.

  3. Rod Photoreceptors Detect Rapid Flicker

    ERIC Educational Resources Information Center

    Conner, J. D.; MacLeod, Donald I. A.

    1977-01-01

    Rod-isolation techniques show that light-adapted human rods detect flicker frequencies as high as 28 hertz, and that the function relating rod critical flicker frequency to stimulus intensity contains two distinct branches. (MLH)

  4. Control rod driveline and grapple

    DOEpatents

    Germer, John H.

    1987-01-01

    A control rod driveline and grapple is disclosed for placement between a control rod drive and a nuclear reactor control rod containing poison for parasitic neutron absorption required for reactor shutdown. The control rod is provided with an enlarged cylindrical handle which terminates in an upwardly extending rod to provide a grapple point for the driveline. The grapple mechanism includes a tension rod which receives the upwardly extending handle and is provided with a lower annular flange. A plurality of preferably six grapple segments surround and grip the control rod handle. Each grapple rod segment grips the flange on the tension rod at an interior upper annular indentation, bears against the enlarged cylindrical handle at an intermediate annulus and captures the upwardly flaring frustum shaped handle at a lower and complementary female segment. The tension rods and grapple segments are surrounded by and encased within a cylinder. The cylinder terminates immediately and outward extending annulus at the lower portion of the grapple segments. Excursion of the tension rod relative to the encasing cylinder causes rod release at the handle by permitting the grapple segments to pivot outwardly and about the annulus on the tension rod so as to open the lower defined frustum shaped annulus and drop the rod. Relative movement between the tension rod and cylinder can occur either due to electromagnetic release of the tension rod within defined limits of travel or differential thermal expansion as between the tension rod and cylinder as where the reactor exceeds design thermal limits.

  5. Understanding flame rods

    SciTech Connect

    McAuley, J.A. Jr.

    1995-11-01

    The flame rod is probably the least understood method of flame detection. Although it is not recommended for oilfired equipment, it is very common on atmospheric, or {open_quotes}in-shot,{close_quotes} gas burners. It is also possible, although not common, to have an application with a constant gas pilot, monitored by a flame rod, and maintaining an oil main flame. Regardless of the application, chances are that flame rods will be encountered during the course of servicing. The technician today must be versatile and able to work on many different types of equipment. One must understand the basic principles of flame rods, and how to correct potential problems. The purpose of a flame detection system is two-fold: (1) to prove there is no flame when there shouldn`t be one, and (2) to prove there is a flame when there should be one. Flame failure response time is very important. This is the amount of time it takes to realize there is a loss of flame, two to four seconds is typical today. Prior to flame rods, either bi-metal or thermocouple type flame detectors were common. The response time for these detectors was up to three minutes, seldom less than one minute.

  6. Intramedullary rodding in osteogenesis imperfecta.

    PubMed

    Mulpuri, K; Joseph, B

    2000-01-01

    The results of intramedullary rodding of long bones of 16 children with osteogenesis imperfecta, over a 10-year period, were analyzed. Sheffield elongating rods or non-elongating rods were used. The frequency of fractures was dramatically reduced after implantation of either type of rod, and the ambulatory status improved in all instances. The results were significantly better after Sheffield rodding with regard to the frequency of complications requiring reoperations and the longevity of the rods. Migration of the rods, encountered frequently, appears to be related to improper placement of the rods in the bone. It seems likely that if care is taken to ensure precise placement of a rod of appropriate size, several of these complications may be avoided. PMID:10739296

  7. COMPOSITE CONTROL ROD

    DOEpatents

    Rock, H.R.

    1963-12-24

    A composite control rod for use in controlling a nuclear reactor is described. The control rod is of sandwich construction in which finned dowel pins are utilized to hold together sheets of the neutron absorbing material and nonabsorbing structural material thereby eliminating the need for being dependent on the absorbing material for structural support. The dowel pins perform the function of absorbing the forces due to differential thermal expansion, seating further with the fins into the sheets of material and crushing before damage is done either to the absorbing or non-absorbing material. (AEC)

  8. Method for producing titanium aluminide weld rod

    DOEpatents

    Hansen, Jeffrey S.; Turner, Paul C.; Argetsinger, Edward R.

    1995-01-01

    A process for producing titanium aluminide weld rod comprising: attaching one end of a metal tube to a vacuum line; placing a means between said vacuum line and a junction of the metal tube to prevent powder from entering the vacuum line; inducing a vacuum within the tube; placing a mixture of titanium and aluminum powder in the tube and employing means to impact the powder in the tube to a filled tube; heating the tube in the vacuum at a temperature sufficient to initiate a high-temperature synthesis (SHS) reaction between the titanium and aluminum; and lowering the temperature to ambient temperature to obtain a intermetallic titanium aluminide alloy weld rod.

  9. Anchor for Fiberglas Guy Rod

    NASA Technical Reports Server (NTRS)

    Wilson, A. H.

    1982-01-01

    Solution to problem of anchoring fiberglas guy rods to install nut with threads on outer circumference, followed by aluminum sleeve. Sleeve has opening oval at upper and round at bottom end. End of rod is split so fiberglas wedge can be inserted to form V-shaped end. Spread end of rod fits into tapered hole in sleeve and threaded aluminum coupling is put over rod and sleeve.

  10. REACTOR CONTROL ROD OPERATING SYSTEM

    DOEpatents

    Miller, G.

    1961-12-12

    A nuclear reactor control rod mechanism is designed which mechanically moves the control rods into and out of the core under normal conditions but rapidly forces the control rods into the core by catapultic action in the event of an emergency. (AEC)

  11. Hafnium stainless steel absorber rod for control rod

    SciTech Connect

    Charnley, J.E.; Cearley, J.E.; Dixon, R.C.; Izzo, K.R.; Aiello, L.L.

    1989-08-01

    This patent describes an improvement in a control rod having a stainless steel body for enclosing a neutron absorbing poison, the control rod having movement along an axial direction for insertion into and out of a nuclear reactor for controlling a nuclear reaction. The improvement comprising: a piece of hafnium; a piece of stainless steel joined to the hafnium by a thin diffusion interface created by friction welding. The hafnium and the stainless steel oriented serially in the axial direction with the thin diffusion interface disposed normal to the axial direction of the control rod movement; means for confining the hafnium to movement along the axial direction with the control rod; and means for attaching the piece of stainless steel to the remaining portion of the control rod to load the weld therebetween under compression or tension during the control rod movement. Whereby the thin diffusion interface is loaded in tension or compression only upon dynamic movement of the control rod.

  12. SAFETY SYSTEM FOR CONTROL ROD

    DOEpatents

    Paget, J.A.

    1963-05-14

    A structure for monitoring the structural continuity of a control rod foi a neutron reactor is presented. A electric conductor readily breakable under mechanical stress is fastened along the length of the control rod at a plurality of positions and forms a closed circuit with remote electrical components responsive to an open circuit. A portion of the conductor between the control rod and said components is helically wound to allow free and normally unrestricted movement of the segment of conductor secured to the control rod relative to the remote components. Any break in the circuit is indicative of control rod breakage. (AEC)

  13. Locked-wrap fuel rod

    DOEpatents

    Kaplan, Samuel; Chertock, Alan J.; Punches, James R.

    1977-01-01

    A method for spacing fast reactor fuel rods using a wire wrapper improved by orienting the wire-wrapped fuel rods in a unique manner which introduces desirable performance characteristics not attainable by previous wire-wrapped designs. Use of this method in a liquid metal fast breeder reactor results in: (a) improved mechanical performance, (b) improved rod-to-rod contact, (c) reduced steel volume, and (d) improved thermal-hydraulic performance. The method produces a "locked wrap" design which tends to lock the rods together at each of the wire cluster locations.

  14. APPARATUS FOR SHEATHING RODS

    DOEpatents

    Ford, W.K.; Wyatt, M.; Plail, S.

    1961-08-01

    An arrangement is described for sealing a solid body of nuclear fuel, such as a uranium metal rod, into a closelyfitting thin metallic sheath with an internal atmosphere of inert gas. The sheathing process consists of subjecting the sheath, loaded with the nuclear fuel body, to the sequential operations of evacuation, gas-filling, drawing (to entrap inert gas and secure close contact between sheath and body), and sealing. (AEC)

  15. Vortices in vibrated granular rods

    NASA Astrophysics Data System (ADS)

    Neicu, Toni; Kudrolli, Arshad

    2002-03-01

    We report the first experimental observation of vortex patterns in granular rods inside a container that is vibrated vertically . The experiments were carried out with an anodized aluminum circular container which is rigidly attached to an electromagnetic shaker and the patterns are imaged using a high-frame rate digital camera. At low rod numbers and driving amplitudes, the rods are observed to lie horizontally. Above a critical number or packing fraction of rods, moving domains of vertical rods are spontaneously observed to form which coexist with horizontal rods. These small domains of vertical rods coarsen over time to form a few large vortices. The size of the vortices increases with the number of rods. We are able to track the ends of the vertical rods and obtain the velocity fields of the vortices. The mean azimuthal velocity as a function of distance from the center of the vortex is obtained as a function of the packing fraction. We will report the phase diagram of the various patterns observed as function of number of rods and driving amplitude. The mechanism for the formation and motion of the domains of vertical rods will be also discussed.

  16. Safety rod latch inspection

    SciTech Connect

    Leader, D.R.

    1992-02-01

    During an attempt to raise control rods from the 100 K reactor in December, one rod could not be withdrawn. Subsequent investigation revealed that a small button'' in the latch mechanism had broken off of the lock plunger'' and was wedged in a position that prevented rod withdrawal. Concern that this failure may have resulted from corrosion or some other metallurgical problem resulted in a request that SRL examine six typical latch mechanisms from the 100 L reactor by use of radiography and metallography. During the examination of the L-Area latches, a failed latch mechanism from the 100 K reactor was added to the investigation. Fourteen latches that had a history of problems were removed from K-Area and sent to SRL for inclusion in this study the week after the original seven assemblies were examined, bringing the total of latch assemblies discussed in this report to twenty one. Results of the examination of the K-Area latch that initiated this study is not included in this report.

  17. Safety rod latch inspection

    SciTech Connect

    Leader, D.R.

    1992-02-01

    During an attempt to raise control rods from the 100 K reactor in December, one rod could not be withdrawn. Subsequent investigation revealed that a small ``button`` in the latch mechanism had broken off of the ``lock plunger`` and was wedged in a position that prevented rod withdrawal. Concern that this failure may have resulted from corrosion or some other metallurgical problem resulted in a request that SRL examine six typical latch mechanisms from the 100 L reactor by use of radiography and metallography. During the examination of the L-Area latches, a failed latch mechanism from the 100 K reactor was added to the investigation. Fourteen latches that had a history of problems were removed from K-Area and sent to SRL for inclusion in this study the week after the original seven assemblies were examined, bringing the total of latch assemblies discussed in this report to twenty one. Results of the examination of the K-Area latch that initiated this study is not included in this report.

  18. Safety analysis forseismic motion of control rods accounting for rod misalignment

    SciTech Connect

    Osmin, W.L.; Paik, I.K.

    1992-01-01

    The purpose of this report is to provide a summary of the results of three safety analyses performed by the SRL Safety Analysis Group (SAG) to assess the safety impact of control rod motion induced by a Design Basis Earthquake (DBE).

  19. Fiber optic laser rod

    DOEpatents

    Erickson, G.F.

    1988-04-13

    A laser rod is formed from a plurality of optical fibers, each forming an individual laser. Synchronization of the individual fiber lasers is obtained by evanescent wave coupling between adjacent optical fiber cores. The fiber cores are dye-doped and spaced at a distance appropriate for evanescent wave coupling at the wavelength of the selected dye. An interstitial material having an index of refraction lower than that of the fiber core provides the optical isolation for effective lasing action while maintaining the cores at the appropriate coupling distance. 2 figs.

  20. Reactor control rod timing system

    DOEpatents

    Wu, Peter T. K.

    1982-01-01

    A fluid driven jet-edge whistle timing system for control rods of a nuclear reactor for producing real-time detection of the timing of each control rod in its scram operation. An important parameter in reactor safety, particularly for liquid metal fast breeder reactors (LMFBR), is the time deviation between the time the control rod is released and the time the rod actually reaches the down position. The whistle has a nearly pure tone signal with center frequency (above 100 kHz) far above the frequency band in which the energy of the background noise is concentrated. Each control rod can be fitted with a whistle with a different frequency so that there is no ambiguity in differentiating the signal from each control rod.

  1. Scaled Long Rod Perforation Experiments Using Multiple Diagnostics

    NASA Astrophysics Data System (ADS)

    Cross, Daniel; Proud, William

    2011-06-01

    A series of angled small-scale reverse ballistic long rod experiments were conducted using mild steel rods (6 mm dia., 90 mm long) against both 3 mm and 6 mm rolled homogeneous armour (RHA) plates at 30°. The impact velocity was varied from 450-780 m s-1 and the response of the system monitored by laser velocimetry, strain gauges and high-speed photography. This provided insight into the flexing of the rod during impact, the acceleration of the rear of the rod and the global penetration process. This experimental series involved ricochet, near-ricochet and full perforation, and so allows the sensitivity of the differing diagnostic outputs for these processes to be compared.

  2. Making Highly Pure Glass Rods

    NASA Technical Reports Server (NTRS)

    Naumann, R. J.

    1986-01-01

    Proposed quasi-containerless method for making glass rods or fibers minimizes contact between processing equipment and product. Method allows greater range of product sizes and shapes than achieved in experiments on containerless processing. Molten zone established in polycrystalline rod. Furnace sections separated, and glass rod solidifies between them. Clamp supports solid glass as it grows in length. Pulling clamp rapidly away from melt draws glass fiber. Fiber diameter controlled by adjustment of pulling rate.

  3. Automatic safety rod for reactors

    DOEpatents

    Germer, John H.

    1988-01-01

    An automatic safety rod for a nuclear reactor containing neutron absorbing material and designed to be inserted into a reactor core after a loss-of-core flow. Actuation is based upon either a sudden decrease in core pressure drop or the pressure drop decreases below a predetermined minimum value. The automatic control rod includes a pressure regulating device whereby a controlled decrease in operating pressure due to reduced coolant flow does not cause the rod to drop into the core.

  4. Piston and connecting rod assembly

    NASA Technical Reports Server (NTRS)

    Brogdon, James William (Inventor); Gill, David Keith (Inventor); Chatten, John K. (Inventor)

    2001-01-01

    A piston and connecting rod assembly includes a piston crown, a piston skirt, a connecting rod, and a bearing insert. The piston skirt is a component separate from the piston crown and is connected to the piston crown to provide a piston body. The bearing insert is a component separate from the piston crown and the piston skirt and is fixedly disposed within the piston body. A bearing surface of a connecting rod contacts the bearing insert to thereby movably associate the connecting rod and the piston body.

  5. Tapered laser rods as a means of minimizing the path length of trapped barrel mode rays

    DOEpatents

    Beach, Raymond J.; Honea, Eric C.; Payne, Stephen A.; Mercer, Ian; Perry, Michael D.

    2005-08-30

    By tapering the diameter of a flanged barrel laser rod over its length, the maximum trapped path length of a barrel mode can be dramatically reduced, thereby reducing the ability of the trapped spontaneous emission to negatively impact laser performance through amplified spontaneous emission (ASE). Laser rods with polished barrels and flanged end caps have found increasing application in diode array end-pumped laser systems. The polished barrel of the rod serves to confine diode array pump light within the rod. In systems utilizing an end-pumping geometry and such polished barrel laser rods, the pump light that is introduced into one or both ends of the laser rod, is ducted down the length of the rod via the total internal reflections (TIRs) that occur when the light strikes the rod's barrel. A disadvantage of using polished barrel laser rods is that such rods are very susceptible to barrel mode paths that can trap spontaneous emission over long path lengths. This trapped spontaneous emission can then be amplified through stimulated emission resulting in a situation where the stored energy available to the desired lasing mode is effectively depleted, which then negatively impacts the laser's performance, a result that is effectively reduced by introducing a taper onto the laser rod.

  6. Composite Lightning Rods for Aircraft

    NASA Technical Reports Server (NTRS)

    Bryan, Charles F., Jr.

    1986-01-01

    Composite, lightweight sacrificial tip with graphite designed reduces lightning-strike damage to composite parts of aircraft and dissipates harmful electrical energy. Device consists of slender composite rod fabricated from highly-conductive unidirectional reinforcing fibers in matrix material. Rods strategically installed in trailing edges of aircraft wings, tails, winglets, control surfaces, and rearward-most portion of aft fuselage.

  7. Rod Climbing of Suspensions

    NASA Astrophysics Data System (ADS)

    Guo, Youjing; Wang, Xiaorong

    We wish to report an unexpected effect observed for particle suspensions sucked to pass through a vertical pipe. Above a critical concentration, the suspension on the outside of the pipe may climb along the outside wall of the pipe and then display a surprising rod-climbing effect. Our study shows that the phenomenon is influenced mainly by the suspension composition, the pipe dimension and the suction speed. The effects of the pipe materials of different kinds are negligible. Increasing the suction force and the concentration increases the climbing height. Increasing the pipe diameter and wall thickness reduces the climbing effect. This behavior may be relevant to that the suspensions of the type described are all displaying markedly shear-thickening.

  8. Fuel axial relocation in ballooning fuel rods. [PWR; BWR

    SciTech Connect

    Siefken, L.J.

    1983-01-01

    Fuel movement, in the longitudinal direction in ballooning fuel rods, shifts the position of heat generation and may cause an increase in cladding temperature in the ballooning region. This paper summarizes the axial fuel relocation data obtained in fuel rod tests conducted in the United States and the Federal Republic of Germany, describes a model for calculating fuel axial relocation, and gives a quantitative analysis of the impact of fuel relocation on cladding temperature. The amount of fuel relocation in 18 ballooned fuel rods was determined from neutron radiographs, niobium gamma decay counts, and photomicrographs. The fuel rods had burnups in the range of 0 to 35,000 MWd/t and cladding hoop strains varying from 0 to 72%.

  9. Regenerative hyperpolarization in rods.

    PubMed Central

    Werblin, F S

    1975-01-01

    1. The electrical properties of the rods in Necturus maculosus were studied at the cell body and the outer segments in dark and light under current and voltage clamp with a pair of intracellular electrodes separated by about 1 mum. 2. The membrane resistance in the dark was voltage- and time-dependent both for the cell body and the outer segment. Slight depolarizations in the cell body reduced the slope resistance from 60 to 10 M omega with a time constant of about 1 sec. Polarization in either direction, at the outer segment, when greater than about 20 mV, reduced the slope resistance from 60 to 30 M omega. The dark potential in the cell body was typically -30 to -35 m V; at the outer segment it was typically only -10 to -15 mV. 3. The light-elicited voltage response in both the cell body and the outer segment was largest with the membrane near the dark potential level. In both regions, the response was reduced when the membrane was polarized in either direction. 4. Under voltage-clamp conditions, a reversal potential for the light response near + 10 mV was measured at the outer segment. At the cell body no reversal potential for the light response was measured; there the clamping current required during the light response was almost of the same magnitude at all potential levels. 5. When the membrane at the cell body was hyperpolarized in the dark under voltage clamp, a transient outward current, typically about one-half the magnitude of the initial inward clamping current was required to maintain the membrane at the clamped potential level. This outward current transient was associated with a decrease in membrane resistance with similar time course. The transient outward current reversed and became inward when the membrane was clamped to potentials more negative than -80 mV. Thus, the transient outward current appears to involve a transient activation initiated by hyperpolarization. I is regenerative in that it is initiated by hyperpolarization and tends to

  10. Status of rod consolidation, 1988

    SciTech Connect

    Bailey, W.J.

    1989-01-01

    It is estimated that the spent fuel storage pools at some domestic light-water reactors will run out of space before 2003, the year that the US Department of Energy currently predicts it will have a repository available. Of the methods being studied to alleviate the problem, rod consolidation is one of the leading candidates for achieving more efficient use of existing space in spent fuel storage pools. Rod consolidation involves mechanically removing all the fuel rods from the fuel assembly hardware (i.e., the structural components) and placing the fuel rods in a close-packed array in a canister without space grids. A typical goal of rod consolidation systems is to insert the fuel rods from two fuel assemblies into a canister that has the same exterior dimensions as one standard fuel assembly (i.e., to achieve a consolidation or compaction ratio of 2:1) and to compact the nonfuel-bearing structural components from those two fuel assemblies by a factor of 10 to 20. This report provides an overview of the current status of rod consolidation in the United States and a small amount of information on related activities in other countries. 85 refs., 36 figs., 5 tabs.

  11. Hopf solitons and elastic rods

    SciTech Connect

    Harland, Derek; Sutcliffe, Paul; Speight, Martin

    2011-03-15

    Hopf solitons in the Skyrme-Faddeev model are stringlike topological solitons classified by the integer-valued Hopf charge. In this paper we introduce an approximate description of Hopf solitons in terms of elastic rods. The general form of the elastic rod energy is derived from the field theory energy and is found to be an extension of the classical Kirchhoff rod energy. Using a minimal extension of the Kirchhoff energy, it is shown that a simple elastic rod model can reproduce many of the qualitative features of Hopf solitons in the Skyrme-Faddeev model. Features that are captured by the model include the buckling of the charge three solution, the formation of links at charges five and six, and the minimal energy trefoil knot at charge seven.

  12. Nuclear design of Helical Cruciform Fuel rods

    SciTech Connect

    Shirvan, K.; Kazimi, M. S.

    2012-07-01

    In order to increase the power density of current and new light water reactor designs, the Helical Cruciform Fuel (HCF) rods are proposed. The HCF rods are equivalent to a cylindrical rod, with the fuel in a cruciform shaped, twisted axially. The HCF rods increase the surface area to volume ratio and inter-subchannel mixing behavior due to their cruciform and helical shapes, respectively. In a previous study, the HCF rods have shown the potential to up-rate existing PWRs by 50% and BWRs by 25%. However, HCF rods do display different neutronics modeling and performance. The cruciform cross section of HCF rods creates radially asymmetric heat generation and temperature distribution. The nominal HCF rod's beginning of life reactivity is reduced, compared to a cylindrical rod with the same fuel volume, by 500 pcm, due to increase in absorption in cladding. The rotation of these rods accounts for reactivity changes, which depends on the H/HM ratio of the pin cell. The HCF geometry shows large sensitivities to U{sup 235} or gadolinium enrichments compared to a cylindrical geometry. In addition, the gadolinium-containing HCF rods show a stronger effect on neighboring HCF rods than in case of cylindrical rods, depending on the orientation of the HCF rods. The helical geometry of the rods introduces axial shadowing of about 600 pcm, not seen in typical cylindrical rods. (authors)

  13. NEUTRONIC REACTOR CONTROL ROD DRIVE APPARATUS

    DOEpatents

    Oakes, L.C.; Walker, C.S.

    1959-12-15

    ABS>A suspension mechanism between a vertically movable nuclear reactor control rod and a rod extension, which also provides information for the operator or an automatic control signal, is described. A spring connects the rod extension to a drive shift. The extension of the spring indicates whether (1) the rod is at rest on the reactor, (2) the rod and extension are suspended, or (3) the extension alone is suspended, the spring controlling a 3-position electrical switch.

  14. Complexity and Self-Organization in Large Arrays of Elastic Rods in an Air Cross-Flow

    NASA Astrophysics Data System (ADS)

    Kuroda, Masaharu; Moon, Francis C.

    2002-07-01

    Experiments on spatio-temporal dynamics in large arrays of cantilevered elastic-rods in uniform and stationary wind-tunnel cross-flow have been carried out. From 90 to 1000 steel and polycarbonate rods with gap ratios ranging from 1.0 to 2.5 are used. As the Reynolds number (based on the rod diameter) increases, a pattern with the characteristics of spatio-temporal chaos emerges in the global behavior of the array of elastic rods. There are local and global patterns. The local patterns are composed of transient rest, linear motions and elliptical motions. In the 90-rod experiments, a cluster-pattern entropy measure is introduced based on these three patterns as a quantitative measure of the local complexity. Below a threshold wind velocity, no significant dynamics appears. Video images reveal that at first each rod moves individually, then clusters consisting of several rods emerge and finally global wave-like motion takes place with higher flow velocities. Spatial patterns in the rod-density distribution appear as more rods suffer impacts with nearest neighbors. Furthermore, these collective nonlinear motions of rods are observed and categorized into several global modes. Using accelerometer data, the rod impact rate versus flow velocity shows a power-law scaling relation. This phenomenon may have application to plant-wind dynamics and damage as well as fluid-structure heat exchange systems. This experiment may also be a two dimensional analog of the impact dynamics of granular materials in a flow.

  15. Stuck fuel rod capping sleeve

    DOEpatents

    Gorscak, Donald A.; Maringo, John J.; Nilsen, Roy J.

    1988-01-01

    A stuck fuel rod capping sleeve to be used during derodding of spent fuel assemblies if a fuel rod becomes stuck in a partially withdrawn position and, thus, has to be severed. The capping sleeve has an inner sleeve made of a lower work hardening highly ductile material (e.g., Inconel 600) and an outer sleeve made of a moderately ductile material (e.g., 304 stainless steel). The inner sleeve may be made of an epoxy filler. The capping sleeve is placed on a fuel rod which is then severed by using a bolt cutter device. Upon cutting, the capping sleeve deforms in such a manner as to prevent the gross release of radioactive fuel material

  16. Advanced gray rod control assembly

    DOEpatents

    Drudy, Keith J; Carlson, William R; Conner, Michael E; Goldenfield, Mark; Hone, Michael J; Long, Jr., Carroll J; Parkinson, Jerod; Pomirleanu, Radu O

    2013-09-17

    An advanced gray rod control assembly (GRCA) for a nuclear reactor. The GRCA provides controlled insertion of gray rod assemblies into the reactor, thereby controlling the rate of power produced by the reactor and providing reactivity control at full power. Each gray rod assembly includes an elongated tubular member, a primary neutron-absorber disposed within the tubular member said neutron-absorber comprising an absorber material, preferably tungsten, having a 2200 m/s neutron absorption microscopic capture cross-section of from 10 to 30 barns. An internal support tube can be positioned between the primary absorber and the tubular member as a secondary absorber to enhance neutron absorption, absorber depletion, assembly weight, and assembly heat transfer characteristics.

  17. Stability and failure analysis of steering tie-rod

    NASA Astrophysics Data System (ADS)

    Jiang, GongFeng; Zhang, YiLiang; Xu, XueDong; Ding, DaWei

    2008-11-01

    A new car in operation of only 8,000 km, because of malfunction, resulting in lost control and rammed into the edge of the road, and then the basic vehicle scrapped. According to the investigation of the site, it was found that the tie-rod of the car had been broken. For the subjective analysis of the accident and identifying the true causes of rupture of the tierod, a series of studies, from the angle of theory to experiment on the bended broken tie-rod, were conducted. The mechanical model was established; the stability of the defective tie-rod was simulated based on ANSYS software. Meanwhile, the process of the accident was simulated considering the effect of destabilization of different vehicle speed and direction of the impact. Simultaneously, macro graphic test, chemical composition analysis, microstructure analysis and SEM analysis of the fracture were implemented. The results showed that: 1) the toughness of the tie-rod is at a normal level, but there is some previous flaws. One quarter of the fracture surface has been cracked before the accident. However, there is no relationship between the flaw and this incident. The direct cause is the dynamic instability leading to the large deformation of impact loading. 2) The declining safety factor of the tie-rod greatly due to the previous flaws; the result of numerical simulation shows that previous flaw is the vital factor of structure instability, on the basis of the comparison of critical loads of the accident tie-rod and normal. The critical load can decrease by 51.3% when the initial defect increases 19.54% on the cross-sectional area, which meets the Theory of Koiter.

  18. Three-Rod Linear Ion Traps

    NASA Technical Reports Server (NTRS)

    Janik, Gary R.; Prestage, John D.; Maleki, Lutfollah

    1993-01-01

    Three-parallel-rod electrode structures proposed for use in linear ion traps and possibly for electrostatic levitation of macroscopic particles. Provides wider viewing angle because they confine ions in regions outside rod-electrode structures.

  19. Control rods in LMFBRs: a physics assessment

    SciTech Connect

    McFarlane, H.F.; Collins, P.J.

    1982-08-01

    This physics assessment is based on roughly 300 control rod worth measurements in ZPPR from 1972 to 1981. All ZPPR assemblies simulated mixed-oxide LMFBRs, representing sizes of 350, 700, and 900 MWe. Control rod worth measurements included single rods, various combinations of rods, and Ta and Eu rods. Additional measurements studied variations in B/sub 4/C enrichment, rod interaction effects, variations in rod geometry, neutron streaming in sodium-filled channels, and axial worth profiles. Analyses were done with design-equivalent methods, using ENDF/B Version IV data. Some computations for the sensitivities to approximations in the methods have been included. Comparisons of these analyses with the experiments have allowed the status of control rod physics in the US to be clearly defined.

  20. Solid-state-laser-rod holder

    DOEpatents

    Gettemy, D.J.; Barnes, N.P.; Griggs, J.E.

    1981-08-11

    The disclosure relates to a solid state laser rod holder comprising Invar, copper tubing, and epoxy joints. Materials and coefficients of expansion of the components of the holder combine with the rod to produce a joint which will give before the rod itself will. The rod may be lased at about 70 to 80/sup 0/K and returned from such a temperature to room temperature repeatedly without its or the holder's destruction.

  1. 21 CFR 876.4270 - Colostomy rod.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Colostomy rod. 876.4270 Section 876.4270 Food and... GASTROENTEROLOGY-UROLOGY DEVICES Surgical Devices § 876.4270 Colostomy rod. (a) Identification. A colostomy rod is a device used during the loop colostomy procedure. A loop of colon is surgically brought out...

  2. 21 CFR 876.4270 - Colostomy rod.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Colostomy rod. 876.4270 Section 876.4270 Food and... GASTROENTEROLOGY-UROLOGY DEVICES Surgical Devices § 876.4270 Colostomy rod. (a) Identification. A colostomy rod is a device used during the loop colostomy procedure. A loop of colon is surgically brought out...

  3. 21 CFR 876.4270 - Colostomy rod.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Colostomy rod. 876.4270 Section 876.4270 Food and... GASTROENTEROLOGY-UROLOGY DEVICES Surgical Devices § 876.4270 Colostomy rod. (a) Identification. A colostomy rod is a device used during the loop colostomy procedure. A loop of colon is surgically brought out...

  4. 21 CFR 876.4270 - Colostomy rod.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Colostomy rod. 876.4270 Section 876.4270 Food and... GASTROENTEROLOGY-UROLOGY DEVICES Surgical Devices § 876.4270 Colostomy rod. (a) Identification. A colostomy rod is a device used during the loop colostomy procedure. A loop of colon is surgically brought out...

  5. Inverted Control Rod Lock-In Device

    DOEpatents

    Brussalis, W. G.; Bost, G. E.

    1962-12-01

    A mechanism which prevents control rods from dropping out of the reactor core in the event the vessel in which the reactor is mounted should capsize is described. The mechanism includes a pivoted toothed armature which engages the threaded control rod lead screw and prevents removal of the rod whenever the armature is not attracted by the provided electromagnetic means. (AEC)

  6. 21 CFR 876.4270 - Colostomy rod.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Colostomy rod. 876.4270 Section 876.4270 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES GASTROENTEROLOGY-UROLOGY DEVICES Surgical Devices § 876.4270 Colostomy rod. (a) Identification. A colostomy rod...

  7. Fuel followed control rod installation at AFRRI

    SciTech Connect

    Moore, Mark; Owens, Chris; Forsbacka, Matt

    1992-07-01

    Fuel Followed Control Rods (FFCRs) were installed at the Armed Forces Radiobiology Research Institute's 1 MW TRIGA Reactor. The procedures for obtaining, shipping, and installing the FFCRs is described. As part of the FFCR installation, the transient rod drive was relocated. Core performance due to the addition of the fuel followed control rods is discussed. (author)

  8. Synaptic transmission from rods to rod-dominated bipolar cells in the tiger salamander retina.

    PubMed

    Yang, X L; Wu, S M

    1993-06-11

    Synaptic transmission between photoreceptors and bipolar cells was studied in dark-adapted tiger salamander retinas. Based on the relative light sensitivity, bipolar cells, either depolarizing (DBC) or hyperpolarizing (HBC), fell into two groups: one receives inputs primarily from rods (rod-dominated bipolar cells, DBCR and HBCR) and the other receives inputs primarily from cones (cone-dominated bipolar cells, DBCC and HBCC). The input-output relations of the rod-DBCR and rod-HBCR synapses were determined by plotting the voltage responses of the rod and DBCR (or HBCR) to dim 500-nm light steps, which polarizes only the rods but not the cones. The slope gains of both synapses were the highest near the dark rod voltage (-2.5 for the rod-DBCR synapse and 4.0 for the rod-HBCR synapse), and they (the absolute values) became progressively smaller at more hyperpolarized rod voltages. PMID:8186975

  9. Manual materials handling in mining: the effect of rod heights and foot positions when lifting "in-the-hole" drill rods.

    PubMed

    Plamondon, André; Delisle, Alain; Trimble, Karin; Desjardins, Pierre; Rickwood, Trevor

    2006-11-01

    There is a paucity of studies focusing on the lifting of rods or long awkward heavy objects. In-the-hole (ITH) drilling is a heavy repetitive mining task, which has been identified as having a relatively high incidence and severity rate of musculoskeletal injuries. The purpose of this study was to examine how the load experienced by ITH drill operators changed when lifting a vertical drilling rod (1.61m, 35kg) using two rod heights and four different foot positions. In addition, a symmetrical lift with a lifting index (LI) of 1.4 also served as a comparison to determine possible risk of low back injury. Eleven experienced ITH drill operators participated in the study. Each subject was required to lift a vertical drilling rod until the upper body was in an erect posture using four different foot positions (0 degrees =subject facing the rod, 45 degrees =subject oblique to the rod, 90 degrees =subject right side to the rod and freestyle). In addition, two rod height conditions were studied where the base of the vertical rod was supported either (1) at ground level (height of rod CG=0.83m) or (2) on a 20cm rack (height of rod CG=1.03m). Finally, each subject lifted a 21.5kg box in the sagittal plane, which corresponded to an LI of 1.4 in the NIOSH lifting equation. Reflective markers were placed on the subjects, and three video cameras and one force plate were used to record the forces and the motion of the subjects' segments. Two surface electrodes were applied on the right and the left erector spinae (ES) at the level of L3. Back loading was defined by the level of the peak moments, the mechanical work and erector spinae muscle activity (EMG). It was found that the vertical height of the rod had the most significant impact on back loading, while the effect of the initial foot positioning relative to the rod was limited by the technique adopted by the drillers. Moreover, it was found that some of the subjects used techniques less strenuous for the back than others

  10. ELECTROMAGNETIC APPARATUS FOR MOVING A ROD

    DOEpatents

    Young, J.N.

    1958-04-22

    An electromagnetic apparatus for moving a rod-like member in small steps in either direction is described. The invention has particular application in the reactor field where the reactor control rods must be moved only a small distance and where the use of mechanical couplings is impractical due to the high- pressure seals required. A neutron-absorbing rod is mounted in a housing with gripping uaits that engage the rod, and coils for magnetizing the gripping units to make them grip, shift, and release the rod are located outside the housing.

  11. Rod cluster having improved vane configuration

    SciTech Connect

    Shockling, L.A.; Francis, T.A.

    1989-09-05

    This patent describes a pressurized water reactor vessel, the vessel defining a predetermined axial direction of the flow of coolant therewithin and having plural spider assemblies supporting, for vertical movement within the vessel, respective clusters of rods in spaced, parallel axial relationship, parallel to the predetermined axial direction of coolant flow, and a rod guide for each spider assembly and respective cluster of rods. The rod guide having horizontally oriented support plates therewithin, each plate having an interior opening for accommodating axial movement therethrough of the spider assembly and respective cluster of rods. The opening defining plural radially extending channels and corresponding parallel interior wall surfaces of the support plate.

  12. Exploiting rod technology. Final report

    SciTech Connect

    1990-06-01

    ROD development was proceeding apace until recent budgetary decisions caused funding support for ROD development to be drastically reduced. The funding which was originally provided by DARPA and the Balanced Technology Initiative (BTI) Office has been cut back to zero from $800K. To determine the aeroballistic coefficients of a candidate dart, ARDEC is currently supporting development out of its own 6.2 funds at about $100K. ARDEC has made slow progress toward achieving this end because of failures in the original dart during testing. It appears that the next dart design to be tested will diverge from the original concept visualized by DARPA and Science and Technology Associates (STA). STA, the design engineer, takes exception to these changes on the basis of inappropriate test conditions and insufficient testing. At this time, the full resolution of this issue will be difficult because of the current management structure, which separates the developer (ARDEC) from the designer (STA).

  13. Tribe kills fuel rod proposal

    SciTech Connect

    1995-02-13

    This article is a review of nuclear utilities` efforts to find a repository of spent fuel rods. The rejection by the Mescalero Apaches of plans to build a waste repository on tribal lands has left a number of utilities scrambling to find interim solutions. Prairie Island will have to close before the end of the year unless a solution is found, and the Hope Creek/Salem units, exhausting there storage capacity within ten years, are considering dry-cask storage.

  14. Fuel rod assembly to manifold attachment

    DOEpatents

    Donck, Harry A.; Veca, Anthony R.; Snyder, Jr., Harold J.

    1980-01-01

    A fuel element is formed with a plurality of fuel rod assemblies detachably connected to an overhead support with each of the fuel rod assemblies having a gas tight seal with the support to allow internal fission gaseous products to flow without leakage from the fuel rod assemblies into a vent manifold passageway system on the support. The upper ends of the fuel rod assemblies are located at vertically extending openings in the support and upper threaded members are threaded to the fuel rod assemblies to connect the latter to the support. The preferred threaded members are cap nuts having a dome wall encircling an upper threaded end on the fuel rod assembly and having an upper sealing surface for sealing contact with the support. Another and lower seal is achieved by abutting a sealing surface on each fuel rod assembly with the support. A deformable portion on the cap nut locks the latter against inadvertent turning off the fuel rod assembly. Orienting means on the fuel rod and support primarily locates the fuel rods azimuthally for reception of a deforming tool for the cap nut. A cross port in the fuel rod end plug discharges into a sealed annulus within the support, which serves as a circumferential chamber, connecting the manifold gas passageways in the support.

  15. A summary of tests on Invar welded with 308L and 8N12 welding rods

    NASA Technical Reports Server (NTRS)

    Cox, J. W.

    1981-01-01

    The cost and difficulty in obtaining Invarod, the recommended welding rod to weld Invar, nessitated the investigation of substituting more readily available rods that would meet the cryogenic design criteria for the National Transonic Facility (NTF). Two weld rods, 308L and 8N12, were chosen as promising candidates. Four welded specimen plates were made; two plates for each type of weld rod. One plate from each of the 308L and 8N12 weldings was thermally cycled 50 times between 366 K and 89 K while the two remaining plates were not thermally cycled. Specimens were machined from all four plates for three types of tests: tensile, charpy impact, and guided-bend. The methods in making the specimen plates, conduction of the tests, test results, and conclusions leading to the selection of a weld rod are presented.

  16. High temperature control rod assembly

    DOEpatents

    Vollman, Russell E.

    1991-01-01

    A high temperature nuclear control rod assembly comprises a plurality of substantially cylindrical segments flexibly joined together in succession by ball joints. The segments are made of a high temperature graphite or carbon-carbon composite. The segment includes a hollow cylindrical sleeve which has an opening for receiving neutron-absorbing material in the form of pellets or compacted rings. The sleeve has a threaded sleeve bore and outer threaded surface. A cylindrical support post has a threaded shaft at one end which is threadably engaged with the sleeve bore to rigidly couple the support post to the sleeve. The other end of the post is formed with a ball portion. A hollow cylindrical collar has an inner threaded surface engageable with the outer threaded surface of the sleeve to rigidly couple the collar to the sleeve. the collar also has a socket portion which cooperates with the ball portion to flexibly connect segments together to form a ball and socket-type joint. In another embodiment, the segment comprises a support member which has a threaded shaft portion and a ball surface portion. The threaded shaft portion is engageable with an inner threaded surface of a ring for rigidly coupling the support member to the ring. The ring in turn has an outer surface at one end which is threadably engageably with a hollow cylindrical sleeve. The other end of the sleeve is formed with a socket portion for engagement with a ball portion of the support member. In yet another embodiment, a secondary rod is slidably inserted in a hollow channel through the center of the segment to provide additional strength. A method for controlling a nuclear reactor utilizing the control rod assembly is also included.

  17. 76 FR 17841 - Record of Decision (ROD) for the Realignment, Growth, and Stationing of Army Aviation Assets

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-31

    ...The Assistant Deputy Chief of Staff of the Army, G-3/5/7, has reviewed the ``Final Programmatic Environmental Impact Statement (FPEIS) for Realignment, Growth, and Stationing of Army Aviation Assets'' and has made the decision to proceed with the implementation of Alternative 3 (preferred alternative). Specific details of the decision are captured in the Army's ROD for this action. This ROD......

  18. Self-assembly of rod-coil-rod ABA-type triblock copolymers.

    PubMed

    Chen, Ji-Zhong; Sun, Zhao-Yan; Zhang, Cheng-Xiang; An, Li-Jia; Tong, Zhen

    2008-02-21

    Self-assembled behavior of symmetric ABA rod-coil-rod triblock copolymer melts is studied by applying self-consistent-field lattice techniques in three-dimensional space. The phase diagram is constructed to understand the effects of the chain architecture on the self-assembled behavior. Four stable structures are observed for the ABA rod-coil-rod triblock, i.e., spherelike, lamellar, gyroidlike, and cylindrical structures. Different from AB rod-coil diblock and BAB coil-rod-coil triblock copolymers, the lamellar structure observed in ABA rod-coil-rod triblock copolymer melts is not stable for high volume fraction of the rod component (f(rod)=0.8), which is attributed to the intramolecular interactions between the two rod blocks of the polymer chain. When 0.3rod)<0.7, the intramolecular interactions between the two rigid blocks of the polymer chain are decrease, which results in the occurrence of some interesting metastable mixed structures. These structures have not been observed in polymers containing only one rod block, such as a lamellar-alt-lamellar structure. The results are expected to provide guidance for the design of microstructures in experiments. PMID:18298171

  19. Reactor control rod timing system. [LMFBR

    DOEpatents

    Wu, P.T.K.

    1980-03-18

    A fluid driven jet-edge whistle timing system is described for control rods of a nuclear reactor for producing real-time detection of the timing of each control rod in its scram operation. An important parameter in reactor safety, particularly for liquid metal fast breeder reactors (LMFBR), is the time deviation between the time the control rod is released and the time the rod actually reaches the down position. The whistle has a nearly pure tone signal with center frequency (above 100 kHz) far above the frequency band in which the energy of the background noise is concentrated. Each control rod can be fitted with a whistle with a different frequency so that there is no ambiguity in differentiating the signal from each control rod.

  20. Scaled long rod perforation experiments using multiple diagnostics: Mild steel against rolled homogeneous armour

    NASA Astrophysics Data System (ADS)

    Cross, Daniel; Proud, William

    2012-03-01

    A series of angled small-scale reverse ballistic long rod experiments were conducted using mild steel rods (6 mm dia., 90 mm long) against both 3 mm and 6 mm rolled homogeneous armour (RHA) plates at 60°. The impact velocity was varied from 450-780 m s-1 and the response of the system monitored by laser velocimetry, strain gauges and high-speed photography. This provided insight into the flexing of the rod during impact, the acceleration of the rear of the rod and the global penetration process. This experimental series involved ricochet, near-ricochet and full perforation, and so allows the sensitivity of the differing diagnostic outputs for these processes to be compared.

  1. Automatic safety rod for reactors. [LMFBR

    DOEpatents

    Germer, J.H.

    1982-03-23

    An automatic safety rod for a nuclear reactor containing neutron absorbing material and designed to be inserted into a reactor core after a loss-of-flow. Actuation is based upon either a sudden decrease in core pressure drop or the pressure drop decreases below a predetermined minimum value. The automatic control rod includes a pressure regulating device whereby a controlled decrease in operating pressure due to reduced coolant flow does not cause the rod to drop into the core.

  2. Growth and Morphology of Rod Eutectics

    SciTech Connect

    Jing Teng; Shan Liu; R. Trivedi

    2008-03-17

    The formation of rod eutectic microstructure is investigated systematically in a succinonitrile-camphor alloy of eutectic composition by using the directional solidification technique. A new rod eutectic configuration is observed in which the rods form with elliptical cylindrical shape. Two different orientations of the ellipse are observed that differ by a 90{sup o} rotation such that the major and the minor axes are interchanged. Critical experiments in thin samples, where a single layer of rods forms, show that the spacing and orientation of the elliptic rods are governed by the growth rate and the sample thickness. In thicker samples, multi layers of rods form with circular cross-section and the scaling law between the spacing and velocity predicted by the Jackson and Hunt model is validated. A theoretical model is developed for a two-dimensional array of elliptical rods that are arranged in a hexagonal or a square array, and the results are shown to be consistent with the experimental observations. The model of elliptic rods is also shown to reduce to that for the circular rod eutectic when the lengths of the two axes are equal, and to the lamellar eutectic model when one of the axes is much larger than the other one.

  3. Temperature actuated automatic safety rod release

    DOEpatents

    Hutter, Ernest; Pardini, John A.; Walker, David E.

    1987-01-01

    A temperature-actuated apparatus is disclosed for releasably supporting a safety rod in a nuclear reactor, comprising a safety rod upper adapter having a retention means, a drive shaft which houses the upper adapter, and a bimetallic means supported within the drive shaft and having at least one ledge which engages a retention means of the safety rod upper adapter. A pre-determined increase in temperature causes the bimetallic means to deform so that the ledge disengages from the retention means, whereby the bimetallic means releases the safety rod into the core of the reactor.

  4. Temperature actuated automatic safety rod release

    DOEpatents

    Hutter, E.; Pardini, J.A.; Walker, D.E.

    1984-03-13

    A temperature-actuated apparatus is disclosed for releasably supporting a safety rod in a nuclear reactor, comprising a safety rod upper adapter having a retention means, a drive shaft which houses the upper adapter, and a bimetallic means supported within the drive shaft and having at least one ledge which engages a retention means of the safety rod upper adapter. A pre-determined increase in temperature causes the bimetallic means to deform so that the ledge disengages from the retention means, whereby the bimetallic means releases the safety rod into the core of the reactor.

  5. The directional sensitivity of retinal rods.

    PubMed Central

    Alpern, M; Ching, C C; Kitahara, K

    1983-01-01

    Rod field sensitivity, 10-S(r) (i.e. the reciprocal of the radiance of a background required for 10-fold elevation of rod threshold) was measured for monochromatic backgrounds traversing the pupil at various points (r) on three subjects. The wave-length dependency of the directional sensitivities of the three foveal cone mechanisms of the principal subject have been reported previously (Alpern & Kitahara, 1983). Rods, as cones, are less sensitive to obliquely incident, than to normally incident backgrounds. At the pupil margin (4 mm) the effect is between 0.368 and 0.976 log10 units smaller for rods. After correction for losses by corneal reflexion and by absorption in the lens, S(r) for rods is reasonably described by the parabolic equation used by Stiles (1937) to quantify the directional sensitivity of cones. The small effect for rods precludes a description as consistently precise as this equation provides for cones. The steepness of the parabolic curve best fitting the directional sensitivity data of the rods of the principal subject was independent of background wave number. For a second subject, whose rods are supposed to be smaller, it was directly proportional to the square of that wave number. The latter is the expectation if the directional sensitivity of this subject's rods were determined by principles outlined in the diffraction theory of Simon (1970). PMID:6644624

  6. Connexin 36 and rod bipolar cell independent rod pathways drive retinal ganglion cells and optokinetic reflexes.

    PubMed

    Cowan, Cameron S; Abd-El-Barr, Muhammad; van der Heijden, Meike; Lo, Eric M; Paul, David; Bramblett, Debra E; Lem, Janis; Simons, David L; Wu, Samuel M

    2016-02-01

    Rod pathways are a parallel set of synaptic connections which enable night vision by relaying and processing rod photoreceptor light responses. We use dim light stimuli to isolate rod pathway contributions to downstream light responses then characterize these contributions in knockout mice lacking rod transducin-α (Trα), or certain pathway components associated with subsets of rod pathways. These comparisons reveal that rod pathway driven light sensitivity in retinal ganglion cells (RGCs) is entirely dependent on Trα, but partially independent of connexin 36 (Cx36) and rod bipolar cells. Pharmacological experiments show that rod pathway-driven and Cx36-independent RGC ON responses are also metabotropic glutamate receptor 6-dependent. To validate the RGC findings in awake, behaving animals we measured optokinetic reflexes (OKRs), which are sensitive to changes in ON pathways. Scotopic OKR contrast sensitivity was lost in Trα(-/-) mice, but indistinguishable from controls in Cx36(-/-) and rod bipolar cell knockout mice. Mesopic OKRs were also altered in mutant mice: Trα(-/-) mice had decreased spatial acuity, rod BC knockouts had decreased sensitivity, and Cx36(-/-) mice had increased sensitivity. These results provide compelling evidence against the complete Cx36 or rod BC dependence of night vision's ON component. Further, the findings suggest the parallel nature of rod pathways provides considerable redundancy to scotopic light sensitivity but distinct contributions to mesopic responses through complicated interactions with cone pathways. PMID:26718442

  7. Computing Temperatures In Optically Pumped Laser Rods

    NASA Technical Reports Server (NTRS)

    Farrukh, Usamah O.

    1991-01-01

    Computer program presents new model solving temperature-distribution problem for laser rods of finite length and calculates both radial and axial components of temperature distributions in these rods. Contains several self-checking schemes to prevent over-writing of memory blocks and to provide simple tracing of information in case of trouble. Written in Microsoft FORTRAN 77.

  8. Tipping Time of a Quantum Rod

    ERIC Educational Resources Information Center

    Parrikar, Onkar

    2010-01-01

    The behaviour of a quantum rod, pivoted at its lower end on an impenetrable floor and restricted to moving in the vertical plane under the gravitational potential, is studied analytically under the approximation that the rod is initially localized to a "small-enough" neighbourhood around the point of classical unstable equilibrium. It is shown…

  9. Vortex Noise from Rotating Cylindrical Rods

    NASA Technical Reports Server (NTRS)

    Stowell, E Z; Deming, A F

    1935-01-01

    A series of round rods of the some diameter were rotated individually about the mid-point of each rod. Vortices are shed from the rods when in motion, giving rise to the emission of sound. With the rotating system placed in the open air, the distribution of sound in space, the acoustical power output, and the spectral distribution have been studied. The frequency of emission of vortices from any point on the rod is given by the formula von Karman. From the spectrum estimates are made of the distribution of acoustical power along the rod, the amount of air concerned in sound production, the "equivalent size" of the vortices, and the acoustical energy content for each vortex.

  10. Rod-Coil Block Polyimide Copolymers

    NASA Technical Reports Server (NTRS)

    Meador, Mary Ann B. (Inventor); Kinder, James D. (Inventor)

    2005-01-01

    This invention is a series of rod-coil block polyimide copolymers that are easy to fabricate into mechanically resilient films with acceptable ionic or protonic conductivity at a variety of temperatures. The copolymers consist of short-rigid polyimide rod segments alternating with polyether coil segments. The rods and coil segments can be linear, branched or mixtures of linear and branched segments. The highly incompatible rods and coil segments phase separate, providing nanoscale channels for ion conduction. The polyimide segments provide dimensional and mechanical stability and can be functionalized in a number of ways to provide specialized functions for a given application. These rod-coil black polyimide copolymers are particularly useful in the preparation of ion conductive membranes for use in the manufacture of fuel cells and lithium based polymer batteries.

  11. A Multi-Stage Wear Model for Grid-to-Rod Fretting of Nuclear Fuel Rods

    SciTech Connect

    Blau, Peter Julian

    2014-01-01

    The wear of fuel rod cladding against the supporting structures in the cores of pressurized water nuclear reactors (PWRs) is an important and potentially costly tribological issue. Grid-to-rod fretting (GTRF), as it is known, involves not only time-varying contact conditions, but also elevated temperatures, flowing hot water, aqueous tribo-corrosion, and the embrittling effects of neutron fluences. The multi-stage, closed-form analytical model described in this paper relies on published out-of-reactor wear and corrosion data and a set of simplifying assumptions to portray the conversion of frictional work into wear depth. The cladding material of interest is a zirconium-based alloy called Zircaloy-4, and the grid support is made of a harder and more wear-resistant material. Focus is on the wear of the cladding. The model involves an incubation stage, a surface oxide wear stage, and a base alloy wear stage. The wear coefficient, which is a measure of the efficiency of conversion of frictional work into wear damage, can change to reflect the evolving metallurgical condition of the alloy. Wear coefficients for Zircaloy-4 and for a polyphase zirconia layer were back-calculated for a range of times required to wear to a critical depth. Inputs for the model, like the friction coefficient, are taken from the tribology literature in lieu of in-reactor tribological data. Concepts of classical fretting were used as a basis, but are modified to enable the model to accommodate the complexities of the PWR environment. Factors like grid spring relaxation, pre-oxidation of the cladding, multiple oxide phases, gap formation, impact, and hydrogen embrittlement are part of the problem definition but uncertainties in their relative roles limits the ability to validate the model. Sample calculations of wear depth versus time in the cladding illustrate how GTRF wear might occur in a discontinuous fashion during months-long reactor operating cycles. A means to account for grid/rod gaps

  12. 75 FR 27996 - Record of Decision (ROD) for the Training Land Acquisition (Including Purchase and Lease) at Fort...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-19

    ... actively managed to promote increased sustainability and reduce environmental impacts. In making its... (Environment, Safety and Occupational Health). BILLING CODE 3710-08-P ... Department of the Army Record of Decision (ROD) for the Training Land Acquisition (Including Purchase...

  13. Eulerian Formulation of Spatially Constrained Elastic Rods

    NASA Astrophysics Data System (ADS)

    Huynen, Alexandre

    Slender elastic rods are ubiquitous in nature and technology. For a vast majority of applications, the rod deflection is restricted by an external constraint and a significant part of the elastic body is in contact with a stiff constraining surface. The research work presented in this doctoral dissertation formulates a computational model for the solution of elastic rods constrained inside or around frictionless tube-like surfaces. The segmentation strategy adopted to cope with this complex class of problems consists in sequencing the global problem into, comparatively simpler, elementary problems either in continuous contact with the constraint or contact-free between their extremities. Within the conventional Lagrangian formulation of elastic rods, this approach is however associated with two major drawbacks. First, the boundary conditions specifying the locations of the rod centerline at both extremities of each elementary problem lead to the establishment of isoperimetric constraints, i.e., integral constraints on the unknown length of the rod. Second, the assessment of the unilateral contact condition requires, in principle, the comparison of two curves parametrized by distinct curvilinear coordinates, viz. the rod centerline and the constraint axis. Both conspire to burden the computations associated with the method. To streamline the solution along the elementary problems and rationalize the assessment of the unilateral contact condition, the rod governing equations are reformulated within the Eulerian framework of the constraint. The methodical exploration of both types of elementary problems leads to specific formulations of the rod governing equations that stress the profound connection between the mechanics of the rod and the geometry of the constraint surface. The proposed Eulerian reformulation, which restates the rod local equilibrium in terms of the curvilinear coordinate associated with the constraint axis, describes the rod deformed configuration

  14. Control Rod Malfunction at the NRAD Reactor

    SciTech Connect

    Thomas L. Maddock

    2010-05-01

    The neutron Radiography Reactor (NRAD) is a training, research, and isotope (TRIGA) reactor located at the INL. The reactor is normally shut down by the insertion of three control rods that drop into the core when power is removed from electromagnets. During a routine shutdown, indicator lights on the console showed that one of the control rods was not inserted. It was initially thought that the indicator lights were in error because of a limit switch that was out of adjustment. Through further testing, it was determined that the control rod did not drop when the scram switch was initially pressed. The control rod anomaly led to a six month shutdown of the reactor and an in depth investigation of the reactor protective system. The investigation looked into: scram switch operation, console modifications, and control rod drive mechanisms. A number of latent issues were discovered and corrected during the investigation. The cause of the control rod malfunction was found to be a buildup of corrosion in the control rod drive mechanism. The investigation resulted in modifications to equipment, changes to both operation and maintenance procedures, and additional training. No reoccurrences of the problem have been observed since corrective actions were implemented.

  15. DEVICE FOR CONTROLLING INSERTION OF ROD

    DOEpatents

    Beaty, B.J.

    1958-10-14

    A device for rapidly inserting a safety rod into a nuclear reactor upon a given signal or in the event of a power failure in order to prevent the possibility of extensive damage caused by a power excursion is described. A piston is slidably mounted within a vertical cylinder with provision for an electromagnetic latch at the top of the cylinder. This assembly, with a safety rod attached to the piston, is mounted over an access port to the core region of the reactor. The piston is normally latched at the top of the cylinder with the safety rod clear of the core area, however, when the latch is released, the piston and rod drop by their own weight to insert the rod. Vents along the side of the cylinder permit the escape of the air entrapped under the piston over the greater part of the distance, however, at the end of the fall the entrapped air is compressed thereby bringing the safety rod gently to rest, thus providing for a rapid automatic insertion of the rod with a minimum of structural shock.

  16. Granular materials interacting with thin flexible rods

    NASA Astrophysics Data System (ADS)

    Neto, Alfredo Gay; Campello, Eduardo M. B.

    2016-01-01

    In this work, we develop a computational model for the simulation of problems wherein granular materials interact with thin flexible rods. We treat granular materials as a collection of spherical particles following a discrete element method (DEM) approach, while flexible rods are described by a large deformation finite element (FEM) rod formulation. Grain-to-grain, grain-to-rod, and rod-to-rod contacts are fully permitted and resolved. A simple and efficient strategy is proposed for coupling the motion of the two types (discrete and continuum) of materials within an iterative time-stepping solution scheme. Implementation details are shown and discussed. Validity and applicability of the model are assessed by means of a few numerical examples. We believe that robust, efficiently coupled DEM-FEM schemes can be a useful tool to the simulation of problems wherein granular materials interact with thin flexible rods, such as (but not limited to) bombardment of grains on beam structures, flow of granular materials over surfaces covered by threads of hair in many biological processes, flow of grains through filters and strainers in various industrial segregation processes, and many others.

  17. Gelation and mechanical response of patchy rods.

    PubMed

    Kazem, Navid; Majidi, Carmel; Maloney, Craig E

    2015-10-28

    We perform Brownian dynamics simulations to study the gelation of suspensions of attractive, rod-like particles. We show that in detail the rod-rod surface interactions can dramatically affect the dynamics of gelation and the structure and mechanics of the networks that form. If the attraction between the rods is perfectly smooth along their length, they will collapse into compact bundles. If the attraction is sufficiently corrugated or patchy, over time, a rigid space-spanning network will form. We study the structure and mechanical properties of the networks that form as a function of the fraction of the surface, f, that is allowed to bind. Surprisingly, the structural and mechanical properties are non-monotonic in f. At low f, there are not a sufficient number of cross-linking sites to form networks. At high f, rods bundle and form disconnected clusters. At intermediate f, robust networks form. The elastic modulus and yield stress are both non-monotonic in the surface coverage. The stiffest and strongest networks show an essentially homogeneous deformation under strain with rods re-orienting along the extensional axis. Weaker, more clumpy networks at high f re-orient relatively little with strong non-affine deformation. These results suggest design strategies for tailoring surface interactions between rods to yield rigid networks with optimal mechanical properties. PMID:26381995

  18. Phototransduction in mouse rods and cones

    PubMed Central

    Fu, Yingbin; Yau, King-Wai

    2010-01-01

    Phototransduction is the process by which light triggers an electrical signal in a photoreceptor cell. Image-forming vision in vertebrates is mediated by two types of photoreceptors: the rods and the cones. In this review, we provide a summary of the success in which the mouse has served as a vertebrate model for studying rod phototransduction, with respect to both the activation and termination steps. Cones are still not as well-understood as rods partly because it is difficult to work with mouse cones due to their scarcity and fragility. The situation may change, however. PMID:17226052

  19. Control rod drive hydraulic system

    DOEpatents

    Ose, Richard A.

    1992-01-01

    A hydraulic system for a control rod drive (CRD) includes a variable output-pressure CR pump operable in a charging mode for providing pressurized fluid at a charging pressure, and in a normal mode for providing the pressurized fluid at a purge pressure, less than the charging pressure. Charging and purge lines are disposed in parallel flow between the CRD pump and the CRD. A hydraulic control unit is disposed in flow communication in the charging line and includes a scram accumulator. An isolation valve is provided in the charging line between the CRD pump and the scram accumulator. A controller is operatively connected to the CRD pump and the isolation valve and is effective for opening the isolation valve and operating the CRD pump in a charging mode for charging the scram accumulator, and closing the isolation valve and operating the CRD pump in a normal mode for providing to the CRD through the purge line the pressurized fluid at a purge pressure lower than the charging pressure.

  20. Optical coherence tomography for nondestructive evaluation of fuel rod degradation

    SciTech Connect

    Renshaw, Jeremy B.; Jenkins, Thomas P. Buckner, Benjamin D.; Friend, Brian

    2015-03-31

    Nuclear power plants regularly inspect fuel rods to ensure safe and reliable operation. Excessive corrosion can cause fuel failures which can have significant repercussions for the plant, including impacts on plant operation, worker exposure to radiation, and the plant's INPO rating. While plants typically inspect for fuel rod corrosion using eddy current techniques, these techniques have known issues with reliability in the presence of tenacious, ferromagnetic crud layers that can deposit during operation, and the nondestructive evaluation (NDE) inspection results can often be in error by a factor of 2 or 3. For this reason, alternative measurement techniques, such as Optical Coherence Tomography (OCT), have been evaluated that are not sensitive to the ferromagnetic nature of the crud. This paper demonstrates that OCT has significant potential to characterize the thickness of crud layers that can deposit on the surfaces of fuel rods during operation. Physical trials have been performed on simulated crud samples, and the resulting data show an apparent correlation between the crud layer thickness and the OCT signal.

  1. Optical coherence tomography for nondestructive evaluation of fuel rod degradation

    NASA Astrophysics Data System (ADS)

    Renshaw, Jeremy B.; Jenkins, Thomas P.; Buckner, Benjamin D.; Friend, Brian

    2015-03-01

    Nuclear power plants regularly inspect fuel rods to ensure safe and reliable operation. Excessive corrosion can cause fuel failures which can have significant repercussions for the plant, including impacts on plant operation, worker exposure to radiation, and the plant's INPO rating. While plants typically inspect for fuel rod corrosion using eddy current techniques, these techniques have known issues with reliability in the presence of tenacious, ferromagnetic crud layers that can deposit during operation, and the nondestructive evaluation (NDE) inspection results can often be in error by a factor of 2 or 3. For this reason, alternative measurement techniques, such as Optical Coherence Tomography (OCT), have been evaluated that are not sensitive to the ferromagnetic nature of the crud. This paper demonstrates that OCT has significant potential to characterize the thickness of crud layers that can deposit on the surfaces of fuel rods during operation. Physical trials have been performed on simulated crud samples, and the resulting data show an apparent correlation between the crud layer thickness and the OCT signal.

  2. Rod electrical coupling is controlled by a circadian clock and dopamine in mouse retina

    PubMed Central

    Jin, Nan Ge; Chuang, Alice Z; Masson, Philippe J; Ribelayga, Christophe P

    2015-01-01

    Key points Rod photoreceptors play a key role in vision in dim light; in the mammalian retina, although rods are anatomically connected or coupled by gap junctions, a type of electrical synapse, the functional importance and regulation of rod coupling has remained elusive. We have developed a new technique in the mouse: perforated patch-clamp recording of rod inner segments in isolated intact retinae maintained by superfusion. We find that rod electrical coupling is controlled by a circadian clock and dopamine, and is weak during the day and stronger at night. The results also indicate that the signal-to-noise ratio for a dim light response is increased at night because of coupling. Our observations will provide a framework for understanding the daily variations in human vision as well as the basis of specific retinal malfunctions. Abstract Rod single-photon responses are critical for vision in dim light. Electrical coupling via gap junction channels shapes the light response properties of vertebrate photoreceptors, but the regulation of rod coupling and its impact on the single-photon response have remained unclear. To directly address these questions, we developed a perforated patch-clamp recording technique and recorded from single rod inner segments in isolated intact neural mouse retinae, maintained by superfusion. Experiments were conducted at different times of the day or under constant environmental conditions, at different times across the circadian cycle. We show that rod electrical coupling is regulated by a circadian clock and dopamine, so that coupling is weak during the day and strong at night. Altogether, patch-clamp recordings of single-photon responses in mouse rods, tracer coupling, receptive field measurements and pharmacological manipulations of gap junction and dopamine receptor activity provide compelling evidence that rod coupling is modulated in a circadian manner. These data are consistent with computer modelling. At night, single

  3. Control rod for a nuclear reactor

    DOEpatents

    Roman, Walter G.; Sutton, Jr., Harry G.

    1979-01-01

    A control rod assembly for a nuclear reactor is disclosed having a remotely disengageable coupling between the control rod and the control rod drive shaft. The coupling is actuated by first lowering then raising the drive shaft. The described motion causes axial repositioning of a pin in a grooved rotatable cylinder, each being attached to different parts of the drive shaft which are axially movable relative to each other. In one embodiment, the relative axial motion of the parts of the drive shaft is used either to couple or to uncouple the connection by forcing resilient members attached to the drive shaft into or out of shouldered engagement, respectively, with an indentation formed in the control rod.

  4. Double-clad nuclear fuel safety rod

    DOEpatents

    McCarthy, William H.; Atcheson, Donald B.; Vaidyanathan, Swaminathan

    1984-01-01

    A device for shutting down a nuclear reactor during an undercooling or overpower event, whether or not the reactor's scram system operates properly. This is accomplished by double-clad fuel safety rods positioned at various locations throughout the reactor core, wherein melting of a secondary internal cladding of the rod allows the fuel column therein to shift from the reactor core to place the reactor in a subcritical condition.

  5. Measurements of control rod efficiency in RBMK critical assembly upon dropping of the rods

    SciTech Connect

    Zhitarev, V. E. Kachanov, V. M.; Sergevnin, A. Yu.; Lebedev, G. V.

    2014-12-15

    The efficiency of control rods in the RBMK critical assembly was measured in the case where one manual-control rod (MCR) is dropped from a steady critical state, and several other MCRs were additionally dropped after 44 s. The measured number of neutrons in the assembly during and after dropping of the rods was used to calculate the efficiency values of the rods by solution of the system of point kinetics equations. A series of methods of the initial data treatment for determination of the desired values of reactivity without the calculated corrections were used.

  6. Development of burnup dependent fuel rod model in COBRA-TF

    NASA Astrophysics Data System (ADS)

    Yilmaz, Mine Ozdemir

    predictions. After confirming that the new fuel thermal conductivity model in CTF worked and provided consistent results with FRAPTRAN predictions for a single fuel rod configuration, the same type of analysis was carried out for a bigger system which is the 4x4 PWR bundle consisting of 15 fuel pins and one control guide tube. Steady- state calculations at Hot Full Power (HFP) conditions for control guide tube out (unrodded) were performed using the 4x4 PWR array with CTF/TORT-TD coupled code system. Fuel centerline, surface and average temperatures predicted by CTF/TORT-TD with and without the new fuel thermal conductivity model were compared against CTF/TORT-TD/FRAPTRAN predictions to demonstrate the improvement in fuel centerline predictions when new model was used. In addition to that constant and CTF dynamic gap conductance model were used with the new thermal conductivity model to show the performance of the CTF dynamic gap conductance model and its impact on fuel centerline and surface temperatures. Finally, a Rod Ejection Accident (REA) scenario using the same 4x4 PWR array was run both at Hot Zero Power (HZP) and Hot Full Power (HFP) condition, starting at a position where half of the control rod is inserted. This scenario was run using CTF/TORT-TD coupled code system with and without the new fuel thermal conductivity model. The purpose of this transient analysis was to show the impact of thermal conductivity degradation (TCD) on feedback effects, specifically Doppler Reactivity Coefficient (DRC) and, eventually, total core reactivity.

  7. Epigenomic landscapes of retinal rods and cones

    PubMed Central

    Mo, Alisa; Luo, Chongyuan; Davis, Fred P; Mukamel, Eran A; Henry, Gilbert L; Nery, Joseph R; Urich, Mark A; Picard, Serge; Lister, Ryan; Eddy, Sean R; Beer, Michael A; Ecker, Joseph R; Nathans, Jeremy

    2016-01-01

    Rod and cone photoreceptors are highly similar in many respects but they have important functional and molecular differences. Here, we investigate genome-wide patterns of DNA methylation and chromatin accessibility in mouse rods and cones and correlate differences in these features with gene expression, histone marks, transcription factor binding, and DNA sequence motifs. Loss of NR2E3 in rods shifts their epigenomes to a more cone-like state. The data further reveal wide differences in DNA methylation between retinal photoreceptors and brain neurons. Surprisingly, we also find a substantial fraction of DNA hypo-methylated regions in adult rods that are not in active chromatin. Many of these regions exhibit hallmarks of regulatory regions that were active earlier in neuronal development, suggesting that these regions could remain undermethylated due to the highly compact chromatin in mature rods. This work defines the epigenomic landscapes of rods and cones, revealing features relevant to photoreceptor development and function. DOI: http://dx.doi.org/10.7554/eLife.11613.001 PMID:26949250

  8. Close packing of rods on spherical surfaces

    NASA Astrophysics Data System (ADS)

    Smallenburg, Frank; Löwen, Hartmut

    2016-04-01

    We study the optimal packing of short, hard spherocylinders confined to lie tangential to a spherical surface, using simulated annealing and molecular dynamics simulations. For clusters of up to twelve particles, we map out the changes in the geometry of the closest-packed configuration as a function of the aspect ratio L/D, where L is the cylinder length and D the diameter of the rods. We find a rich variety of cluster structures. For larger clusters, we find that the best-packed configurations up to around 100 particles are highly dependent on the exact number of particles and aspect ratio. For even larger clusters, we find largely disordered clusters for very short rods (L/D = 0.25), while slightly longer rods (L/D = 0.5 or 1) prefer a global baseball-like geometry of smectic-like domains, similar to the behavior of large-scale nematic shells. Intriguingly, we observe that when compared to their optimal flat-plane packing, short rods adapt to the spherical geometry more efficiently than both spheres and longer rods. Our results provide predictions for experimentally realizable systems of colloidal rods trapped at the interface of emulsion droplets.

  9. Close packing of rods on spherical surfaces.

    PubMed

    Smallenburg, Frank; Löwen, Hartmut

    2016-04-28

    We study the optimal packing of short, hard spherocylinders confined to lie tangential to a spherical surface, using simulated annealing and molecular dynamics simulations. For clusters of up to twelve particles, we map out the changes in the geometry of the closest-packed configuration as a function of the aspect ratio L/D, where L is the cylinder length and D the diameter of the rods. We find a rich variety of cluster structures. For larger clusters, we find that the best-packed configurations up to around 100 particles are highly dependent on the exact number of particles and aspect ratio. For even larger clusters, we find largely disordered clusters for very short rods (L/D = 0.25), while slightly longer rods (L/D = 0.5 or 1) prefer a global baseball-like geometry of smectic-like domains, similar to the behavior of large-scale nematic shells. Intriguingly, we observe that when compared to their optimal flat-plane packing, short rods adapt to the spherical geometry more efficiently than both spheres and longer rods. Our results provide predictions for experimentally realizable systems of colloidal rods trapped at the interface of emulsion droplets. PMID:27131565

  10. High-throughput rod-induced electrospinning

    NASA Astrophysics Data System (ADS)

    Wu, Dezhi; Xiao, Zhiming; Teh, Kwok Siong; Han, Zhibin; Luo, Guoxi; Shi, Chuan; Sun, Daoheng; Zhao, Jinbao; Lin, Liwei

    2016-09-01

    A high throughput electrospinning process, directly from flat polymer solution surfaces induced by a moving insulating rod, has been proposed and demonstrated. Different rods made of either phenolic resin or paper with a diameter of 1–3 cm and a resistance of about 100–500 MΩ, has been successfully utilized in the process. The rod is placed approximately 10 mm above the flat polymer solution surface with a moving speed of 0.005–0.4 m s‑1 this causes the solution to generate multiple liquid jets under an applied voltage of 15–60 kV for the tip-less electrospinning process. The local electric field induced by the rod can boost electrohydrodynamic instability in order to generate Taylor cones and liquid jets. Experimentally, it is found that a large rod diameter and a small solution-to-rod distance can enhance the local electrical field to reduce the magnitude of the applied voltage. In the prototype setup with poly (ethylene oxide) polymer solution, an area of 5 cm  ×  10 cm and under an applied voltage of 60 kV, the maximum throughput of nanofibers is recorded to be approximately144 g m‑2 h‑1.

  11. 49 CFR 230.93 - Pistons and piston rods.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Pistons and piston rods. 230.93 Section 230.93... Tenders Driving Gear § 230.93 Pistons and piston rods. (a) Maintenance and testing. Pistons and piston rods shall be maintained in safe and suitable condition for service. Piston rods shall be inspected...

  12. International symposium on fuel rod simulators: development and application

    SciTech Connect

    McCulloch, R.W.

    1981-05-01

    Separate abstracts are included for each of the papers presented concerning fuel rod simulator operation and performance; simulator design and evaluation; clad heated fuel rod simulators and fuel rod simulators for cladding investigations; fuel rod simulator components and inspection; and simulator analytical modeling. Ten papers have previously been input to the Energy Data Base.

  13. Mechanical performance of fiberglass sucker-rod strings

    SciTech Connect

    Tripp, H.A.

    1988-08-01

    The natural frequencies of fiberglass sucker-rod strings can be calculated by treating the rod strings as modified spring/mass vibration systems. The ratio of the pumping-unit operating speed to the rod-string natural frequency can then be used as a basis for understanding fiberglass-rod performance and for predicting downhole pump stroke lengths.

  14. Nuclear reactor remote disconnect control rod coupling indicator

    DOEpatents

    Vuckovich, Michael

    1977-01-01

    A coupling indicator for use with nuclear reactor control rod assemblies which have remotely disengageable couplings between the control rod and the control rod drive shaft. The coupling indicator indicates whether the control rod and the control rod drive shaft are engaged or disengaged. A resistive network, utilizing magnetic reed switches, senses the position of the control rod drive mechanism lead screw and the control rod position indicating tube, and the relative position of these two elements with respect to each other is compared to determine whether the coupling is engaged or disengaged.

  15. The Consequences of Hypomorphic RPE65 for Rod and Cone Photoreceptors.

    PubMed

    Samardzija, Marijana; Barben, Maya; Geiger, Philipp; Grimm, Christian

    2016-01-01

    RPE65 is essential for both rod- and cone-mediated vision. So far, more than 120 disease-associated mutations have been identified in the human RPE65 gene. Differential clinical manifestations suggested that some patients suffer from null mutations while others retain residual RPE65 activity and some useful vision. To understand the mechanism of retinal degeneration or dysfunction caused by such hypomorphic RPE65 alleles, we generated an Rpe65 (R91W) knock-in mouse (R91W) that expresses a mutant RPE65 protein with reduced function. Data obtained suggested that the R91W mouse is highly suitable to study the impact of RPE65 insufficiency on rod pathophysiology. To study the impact on cones, we combined the R91W with the Nrl (-/-) mouse that develops an all-cone retina. Here we summarize the consequences of hypomorphic RPE65 function (reduced 11-cis-retinal synthesis) for rod and cone pathophysiology. PMID:26427430

  16. Photovoltage of Rods and Cones in the Macaque Retina

    NASA Astrophysics Data System (ADS)

    Schneeweis, David M.; Schnapf, Julie L.

    1995-05-01

    The kinetics, gain, and reliability of light responses of rod and cone photoreceptors are important determinants of overall visual sensitivity. In voltage recordings from photoreceptors in an intact primate retina, rods were found to be functionally isolated from each other, unlike the tightly coupled rods of cold-blooded vertebrates. Cones were observed to receive excitatory input from rods, which indicates that the cone pathway also processes rod signals. This input might be expected to degrade the spatial resolution of mesopic vision.

  17. Regulatory perspective on incomplete control rod insertions

    SciTech Connect

    Chatterton, M.

    1997-01-01

    The incomplete control rod insertions experienced at South Texas Unit 1 and Wolf Creek are of safety concern to the NRC staff because they represent potential precursors to loss of shutdown margin. Even before it was determined if these events were caused by the control rods or by the fuel there was an apparent correlation of the problem with high burnup fuel. It was determined that there was also a correlation between high burnup and high drag forces as well as with rod drop time histories and lack of rod recoil. The NRC staff initial actions were aimed at getting a perspective on the magnitude of the problem as far as the number of plants and the amount of fuel that could be involved, as well as the safety significance in terms of shutdown margin. As tests have been performed and data has been analyzed the focus has shifted more toward understanding the problem and the ways to eliminate it. At this time the staff`s understanding of the phenomena is that it was a combination of factors including burnup, power history and temperature. The problem appears to be very sensitive to these factors, the interaction of which is not clearly understood. The model developed by Westinghouse provides a possible explanation but there is not sufficient data to establish confidence levels and sensitivity studies involving the key parameters have not been done. While several fixes to the problem have been discussed, no definitive fixes have been proposed. Without complete understanding of the phenomena, or fixes that clearly eliminate the problem the safety concern remains. The safety significance depends on the amount of shutdown margin lost due to incomplete insertion of the control rods. Were the control rods to stick high in the core, the reactor could not be shutdown by the control rods and other means such as emergency boration would be required.

  18. 75 FR 997 - Record of Decision (ROD) on the U.S. Coast Guard Long Range Aids to Navigation (Loran-C) Program

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-07

    ...The Department of Homeland Security (DHS), United States Coast Guard (USCG), announces the availability of the Record of Decision (ROD) to decommission the USCG Loran-C Program and terminate transmission of the North American Loran-C Radionavigation Signal. The ROD is supported by the Final Programmatic Environmental Impact Statement (PEIS) addressing the future of the USCG Loran-C Program.......

  19. Fuel rod mechanical deformation during the PBF/LOFT lead rod loss-of-coolant experiments

    SciTech Connect

    Varacalle, Jr., D. J.; MacDonald, P. E.; Shiozawa, S.; Driskell, W. E.

    1980-01-01

    Results of four PBF/LOFT Lead Rod (LLR) sequential blowdown tests conducted in the Power Burst Facility (PBF) are presented. Each test employed four separately shrouded fuel rods. The primary objective of the test series was to evaluate the extent of mechanical deformation that would be expected to occur to low pressure (0.1 MPa), light water reactor design fuel rods when subjected to a series of double ended cold leg break loss-of-coolant accident (LOCA) tests, and to determine whether subjecting these deformed fuel rods to subsequent testing would result in rod failure. The extent of mechanical deformation (buckling, collapse, or waisting of the cladding) was evaluated by comparison of cladding temperature and system pressure measurements with out-of-pile experimental data, and by posttest visual examinations and cladding diametral measurements.

  20. Radiological characterization of spent control rod assemblies

    SciTech Connect

    Lepel, E.A.; Robertson, D.E.; Thomas, C.W.; Pratt, S.L.; Haggard, D.L.

    1995-10-01

    This document represents the final report of an ongoing study to provide radiological characterizations, classifications, and assessments in support of the decommissioning of nuclear power stations. This report describes the results of non-destructive and laboratory radionuclide measurements, as well as waste classification assessments, of BWR and PWR spent control rod assemblies. The radionuclide inventories of these spent control rods were determined by three separate methodologies, including (1) direct assay techniques, (2) calculational techniques, and (3) by sampling and laboratory radiochemical analyses. For the BWR control rod blade (CRB) and PWR burnable poison rod assembly (BPRA), {sup 60}Co and {sup 63}Ni, present in the stainless steel cladding, were the most abundant neutron activation products. The most abundant radionuclide in the PWR rod cluster control assembly (RCCA) was {sup 108m}Ag (130 yr halflife) produced in the Ag-In-Cd alloy used as the neutron poison. This radionuclide will be the dominant contributor to the gamma dose rate for many hundreds of years. The results of the direct assay methods agree very well ({+-}10%) with the sampling/radiochemical measurements. The results of the calculational methods agreed fairly well with the empirical measurements for the BPRA, but often varied by a factor of 5 to 10 for the CRB and the RCCA assemblies. If concentration averaging and encapsulation, as allowed by 10CFR61.55, is performed, then each of the entire control assemblies would be classified as Class C low-level radioactive waste.

  1. Passive electrical properties of rod outer segments

    PubMed Central

    Falk, Gertrude; Fatt, P.

    1968-01-01

    1. Measurements on a packed suspension of randomly oriented, dark-adapted frog rods at frequencies of 15 c/s-0·5 Mc/s indicate a behaviour similar to that of other biological materials. 2. Results are analysed on the assumption that the low-frequency limiting resistance is determined by current flowing in the suspending medium and that, of the rods, two thirds are oriented perpendicular to the applied field and one third parallel to it. Those parallel to the field are treated as non-conductors. 3. From the high-frequency limiting resistance the conductivity of the rod interior is calculated to vary linearly with the conductivity of the medium. The slope of the relation of internal to external conductivity is 0·50 with a limiting internal conductivity (at zero external) of 280 μmho/cm. 4. On the assumption that the suspension can be represented as a single-capacitance network, the characteristic frequency of impedance is used to calculate a capacitance for the rod surface of 1·54 μF/cm2. On the assumption of a distribution in properties of the suspension according to the theory of Bruggeman, the capacitance is calculated to have a value of about one half this. 5. At frequencies below 5 kc/s the impedance locus deviates from the curve describing the behaviour at higher frequencies. It is suggested that this may involve conduction in a thin layer extending along the surface of the rod. PMID:5685292

  2. Gelation And Mechanical Response of Patchy Rods

    NASA Astrophysics Data System (ADS)

    Kazem, Navid; Majidi, Carmel; Maloney, Craig

    We perform Brownian Dynamics simulations to study the gelation of suspensions of attractive, rod-like particles. We show that details of the particle-particle interactions can dramatically affect the dynamics of gelation and the structure and mechanics of the networks that form. If the attraction between the rods is perfectly smooth along their length, they will collapse into compact bundles. If the attraction is sufficiently corrugated or patchy, over time, a rigid space spanning network forms. We study the structure and mechanical properties of the networks that form as a function of the fraction of the surface that is allowed to bind. Surprisingly, the structural and mechanical properties are non-monotonic in the surface coverage. At low coverage, there are not a sufficient number of cross-linking sites to form networks. At high coverage, rods bundle and form disconnected clusters. At intermediate coverage, robust networks form. The elastic modulus and yield stress are both non-monotonic in the surface coverage. The stiffest and strongest networks show an essentially homogeneous deformation under strain with rods re-orienting along the extensional axis. Weaker, clumpy networks at high surface coverage exhibit relatively little re-orienting with strong non-affine deformation. These results suggest design strategies for tailoring surface interactions between rods to yield rigid networks with optimal properties. National Science Foundation and the Air Force Office of Scientific Research.

  3. Coiling of elastic rods on rigid substrates.

    PubMed

    Jawed, Mohammad K; Da, Fang; Joo, Jungseock; Grinspun, Eitan; Reis, Pedro M

    2014-10-14

    We investigate the deployment of a thin elastic rod onto a rigid substrate and study the resulting coiling patterns. In our approach, we combine precision model experiments, scaling analyses, and computer simulations toward developing predictive understanding of the coiling process. Both cases of deposition onto static and moving substrates are considered. We construct phase diagrams for the possible coiling patterns and characterize them as a function of the geometric and material properties of the rod, as well as the height and relative speeds of deployment. The modes selected and their characteristic length scales are found to arise from a complex interplay between gravitational, bending, and twisting energies of the rod, coupled to the geometric nonlinearities intrinsic to the large deformations. We give particular emphasis to the first sinusoidal mode of instability, which we find to be consistent with a Hopf bifurcation, and analyze the meandering wavelength and amplitude. Throughout, we systematically vary natural curvature of the rod as a control parameter, which has a qualitative and quantitative effect on the pattern formation, above a critical value that we determine. The universality conferred by the prominent role of geometry in the deformation modes of the rod suggests using the gained understanding as design guidelines, in the original applications that motivated the study. PMID:25267649

  4. Dynamic behavior of rod photoreceptor disks.

    PubMed

    Chen, Chunhe; Jiang, Yunhai; Koutalos, Yiannis

    2002-09-01

    Eukaryotic cells use membrane organelles, like the endoplasmic reticulum or the Golgi, to carry out different functions. Vertebrate rod photoreceptors use hundreds of membrane sacs (the disks) for the detection of light. We have used fluorescent tracers and single cell imaging to study the properties of rod photoreceptor disks. Labeling of intact rod photoreceptors with membrane markers and polar tracers revealed communication between intradiskal and extracellular space. Internalized tracers moved along the length of the rod outer segment, indicating communication between the disks as well. This communication involved the exchange of both membrane and aqueous phase and had a time constant in the order of minutes. The communication pathway uses approximately 2% of the available membrane disk area and does not allow the passage of molecules larger than 10 kDa. It was possible to load the intradiskal space with fluorescent Ca(2+) and pH dyes, which reported an intradiskal Ca(2+) concentration in the order of 1 microM and an acidic pH 6.5, both of them significantly different than intracellular and extracellular Ca(2+) concentrations and pH. The results suggest that the rod photoreceptor disks are not discrete, passive sacs but rather comprise an active cellular organelle. The communication between disks may be important for membrane remodeling as well as for providing access to the intradiskal space of the whole outer segment. PMID:12202366

  5. Single Rod Vibration in Axial Flow

    NASA Astrophysics Data System (ADS)

    Weichselbaum, Noah; Wang, Shengfu; Bardet, Philippe

    2013-11-01

    Fluid structure interaction of a single rod in axial flow is a coupled dynamical system present in many application including nuclear reactors, steam generators, and towed antenna arrays. Fluid-structure response can be quantified thanks to detailed experimental data where both structure and fluid responses are recorded. Such datum deepen understanding of the physics inherent to the system and provide high-dimensionality quantitative measurements to validate coupled structural and CFD codes with various level of complexity. In this work, single rods fixed on both ends in a concentric pipe, are subjected to an axial flow with Reynolds number based on hydraulic diameter of Re =4000. Rods of varying material stiffness and diameter are utilized in the experiment resulting in a range of dimensionless U between 0.5 and 1, where U = (ρA/EI)1/2uL. Experimental measurements of the velocity field around the rod are taken with PIV from time-resolved Nd:YLF laser and a high speed CMOS camera. Three-dimensional and temporal vibration and deflection of the rod is recorded with shadowgraphy utilizing two sets of pulsed high power LED and dedicated CMOS camera. Through integration of these two diagnostics, it is possible to reconstruct the full FSI domain providing unique validation data.

  6. Coiling of elastic rods on rigid substrates

    PubMed Central

    Jawed, Mohammad K.; Da, Fang; Joo, Jungseock; Grinspun, Eitan; Reis, Pedro M.

    2014-01-01

    We investigate the deployment of a thin elastic rod onto a rigid substrate and study the resulting coiling patterns. In our approach, we combine precision model experiments, scaling analyses, and computer simulations toward developing predictive understanding of the coiling process. Both cases of deposition onto static and moving substrates are considered. We construct phase diagrams for the possible coiling patterns and characterize them as a function of the geometric and material properties of the rod, as well as the height and relative speeds of deployment. The modes selected and their characteristic length scales are found to arise from a complex interplay between gravitational, bending, and twisting energies of the rod, coupled to the geometric nonlinearities intrinsic to the large deformations. We give particular emphasis to the first sinusoidal mode of instability, which we find to be consistent with a Hopf bifurcation, and analyze the meandering wavelength and amplitude. Throughout, we systematically vary natural curvature of the rod as a control parameter, which has a qualitative and quantitative effect on the pattern formation, above a critical value that we determine. The universality conferred by the prominent role of geometry in the deformation modes of the rod suggests using the gained understanding as design guidelines, in the original applications that motivated the study. PMID:25267649

  7. Rod consolidation at the West Valley Demonstration Project

    SciTech Connect

    Bailey, W.J.

    1986-12-01

    A rod consolidation demonstration with irradiated pressurized water reactor fuel was recently conducted by personnel from Nuclear Assurance Corporation and West Valley Nuclear Services Company at the West Valley Demonstration Project in West Valley, New York. The rod consolidation demonstration involved pulling all of the fuel rods from six fuel Assemblies. In general, the rod pulling proceeded smoothly. The highest compaction ratio attained was 1:8:1. Among the total of 1074 fuel rods were some known degraded rods (they had collapsed cladding, a result of in-reactor fuel densification), but no rods were broken or dropped during the demonstration. One aim was to gather information on the effect of rod consolidation operations on the integrity of the fuel rods during subsequent handling and storage. Another goal was to collect information on the condition and handling of intact, damaged, and failed fuel that has been in storage for an extended period. 9 refs., 8 figs., 1 tab.

  8. Magnetic switch for reactor control rod

    DOEpatents

    Germer, John H.

    1986-01-01

    A magnetic reed switch assembly for activating an electromagnetic grapple utilized to hold a control rod in position above a reactor core. In normal operation the magnetic field of a permanent magnet is short-circuited by a magnetic shunt, diverting the magnetic field away from the reed switch. The magnetic shunt is made of a material having a Curie-point at the desired release temperature. Above that temperature the material loses its ferromagnetic properties, and the magnetic path is diverted to the reed switch which closes and short-circuits the control circuit for the control rod electromagnetic grapple which allows the control rod to drop into the reactor core for controlling the reactivity of the core.

  9. Magnetic switch for reactor control rod. [LMFBR

    DOEpatents

    Germer, J.H.

    1982-09-30

    A magnetic reed switch assembly is described for activating an electromagnetic grapple utilized to hold a control rod in position above a reactor core. In normal operation the magnetic field of a permanent magnet is short-circuited by a magnetic shunt, diverting the magnetic field away from the reed switch. The magnetic shunt is made of a material having a Curie-point at the desired release temperature. Above that temperature the material loses its ferromagnetic properties, and the magnetic path is diverted to the reed switch which closes and short-circuits the control circuit for the control rod electro-magnetic grapple which allows the control rod to drop into the reactor core for controlling the reactivity of the core.

  10. Studying rod photoreceptor development in zebrafish

    PubMed Central

    Morris, A.C.; Fadool, J.M.

    2009-01-01

    The zebrafish has rapidly become a favored model vertebrate organism, well suited for studies of developmental processes using large-scale genetic screens. In particular, zebrafish morphological and behavioral genetic screens have led to the identification of genes important for development of the retinal photoreceptors. This may help clarify the genetic mechanisms underlying human photoreceptor development and dysfunction in retinal diseases. In this review, we present the advantages of zebrafish as a vertebrate model organism, summarize retinal and photoreceptor cell development in zebrafish, with emphasis on the rod photoreceptors, and describe zebrafish visual behaviors that can be used for genetic screens. We then describe some of the photoreceptor cell mutants that have been isolated in morphological and behavioral screens and discuss the limitations of current screening methods for uncovering mutations that specifically affect rod function. Finally, we present some alternative strategies to target the rod developmental pathway in zebrafish. PMID:16199068

  11. Nuclear reactor fuel rod attachment system

    DOEpatents

    Not Available

    1980-09-17

    A reusable system is described for removably attaching a nuclear reactor fuel rod to a support member. A locking cap is secured to the fuel rod and a locking strip is fastened to the support member. The locking cap has two opposing fingers shaped to form a socket having a body portion. The locking strip has an extension shaped to rigidly attach to the socket's body portion. The locking cap's fingers are resiliently deflectable. For attachment, the locking cap is longitudinally pushed onto the locking strip causing the extension to temporarily deflect open the fingers to engage the socket's body portion. For removal, the process is reversed.

  12. HIGH STRENGTH CONTROL RODS FOR NEUTRONIC REACTORS

    DOEpatents

    Lustman, B.; Losco, E.F.; Cohen, I.

    1961-07-11

    Nuclear reactor control rods comprised of highly compressed and sintered finely divided metal alloy panticles and fine metal oxide panticles substantially uniformly distributed theretbrough are described. The metal alloy consists essentially of silver, indium, cadmium, tin, and aluminum, the amount of each being present in centain percentages by weight. The oxide particles are metal oxides of the metal alloy composition, the amount of oxygen being present in certain percentages by weight and all the oxygen present being substantially in the form of metal oxide. This control rod is characterized by its high strength and resistance to creep at elevated temperatures.

  13. Control rod drive for reactor shutdown

    DOEpatents

    McKeehan, Ernest R.; Shawver, Bruce M.; Schiro, Donald J.; Taft, William E.

    1976-01-20

    A means for rapidly shutting down or scramming a nuclear reactor, such as a liquid metal-cooled fast breeder reactor, and serves as a backup to the primary shutdown system. The control rod drive consists basically of an in-core assembly, a drive shaft and seal assembly, and a control drive mechanism. The control rod is driven into the core region of the reactor by gravity and hydraulic pressure forces supplied by the reactor coolant, thus assuring that common mode failures will not interfere with or prohibit scramming the reactor when necessary.

  14. Method and means of packaging nuclear fuel rods for handling

    DOEpatents

    Adam, Milton F.

    1979-01-01

    Nuclear fuel rods, especially spent nuclear fuel rods that may show physical distortion, are encased within a metallic enclosing structure by forming a tube about the fuel rod. The tube has previously been rolled to form an overlapping tubular structure and then unrolled and coiled about an axis perpendicular to the tube. The fuel rod is inserted into the tube as the rolled tube is removed from a coiled strip and allowed to reassume its tubular shape about the fuel rod. Rollers support the coiled strip in an open position as the coiled strip is uncoiled and allowed to roll about the fuel rod.

  15. Cavitation phenomena in mechanical heart valves: studied by using a physical impinging rod system.

    PubMed

    Lo, Chi-Wen; Chen, Sheng-Fu; Li, Chi-Pei; Lu, Po-Chien

    2010-10-01

    When studying mechanical heart valve cavitation, a physical model allows direct flow field and pressure measurements that are difficult to perform with actual valves, as well as separate testing of water hammer and squeeze flow effects. Movable rods of 5 and 10 mm diameter impinged same-sized stationary rods to simulate squeeze flow. A 24 mm piston within a tube simulated water hammer. Adding a 5 mm stationary rod within the tube generated both effects simultaneously. Charged-coupled device (CCD) laser displacement sensors, strobe lighting technique, laser Doppler velocimetry (LDV), particle image velocimetry (PIV) and high fidelity piezoelectric pressure transducers measured impact velocities, cavitation images, squeeze flow velocities, vortices, and pressure changes at impact, respectively. The movable rods created cavitation at critical impact velocities of 1.6 and 1.2 m/s; squeeze flow velocities were 2.8 and 4.64 m/s. The isolated water hammer created cavitation at 1.3 m/s piston speed. The combined piston and stationary rod created cavitation at an impact speed of 0.9 m/s and squeeze flow of 3.2 m/s. These results show squeeze flow alone caused cavitation, notably at lower impact velocity as contact area increased. Water hammer alone also caused cavitation with faster displacement. Both effects together were additive. The pressure change at the vortex center was only 150 mmHg, which cannot generate the magnitude of pressure drop required for cavitation bubble formation. Cavitation occurred at 3-5 m/s squeeze flow, significantly different from the 14 m/s derived by Bernoulli's equation; the temporal acceleration of unsteady flow requires further study. PMID:20490686

  16. Modeling and simulation performance of sucker rod beam pump

    SciTech Connect

    Aditsania, Annisa; Rahmawati, Silvy Dewi Sukarno, Pudjo; Soewono, Edy

    2015-09-30

    Artificial lift is a mechanism to lift hydrocarbon, generally petroleum, from a well to surface. This is used in the case that the natural pressure from the reservoir has significantly decreased. Sucker rod beam pumping is a method of artificial lift. Sucker rod beam pump is modeled in this research as a function of geometry of the surface part, the size of sucker rod string, and fluid properties. Besides its length, sucker rod string also classified into tapered and un-tapered. At the beginning of this research, for easy modeling, the sucker rod string was assumed as un-tapered. The assumption proved non-realistic to use. Therefore, the tapered sucker rod string modeling needs building. The numerical solution of this sucker rod beam pump model is computed using finite difference method. The numerical result shows that the peak of polished rod load for sucker rod beam pump unit C-456-D-256-120, for non-tapered sucker rod string is 38504.2 lb, while for tapered rod string is 25723.3 lb. For that reason, to avoid the sucker rod string breaks due to the overload, the use of tapered sucker rod beam string is suggested in this research.

  17. Modeling and simulation performance of sucker rod beam pump

    NASA Astrophysics Data System (ADS)

    Aditsania, Annisa; Rahmawati, Silvy Dewi; Sukarno, Pudjo; Soewono, Edy

    2015-09-01

    Artificial lift is a mechanism to lift hydrocarbon, generally petroleum, from a well to surface. This is used in the case that the natural pressure from the reservoir has significantly decreased. Sucker rod beam pumping is a method of artificial lift. Sucker rod beam pump is modeled in this research as a function of geometry of the surface part, the size of sucker rod string, and fluid properties. Besides its length, sucker rod string also classified into tapered and un-tapered. At the beginning of this research, for easy modeling, the sucker rod string was assumed as un-tapered. The assumption proved non-realistic to use. Therefore, the tapered sucker rod string modeling needs building. The numerical solution of this sucker rod beam pump model is computed using finite difference method. The numerical result shows that the peak of polished rod load for sucker rod beam pump unit C-456-D-256-120, for non-tapered sucker rod string is 38504.2 lb, while for tapered rod string is 25723.3 lb. For that reason, to avoid the sucker rod string breaks due to the overload, the use of tapered sucker rod beam string is suggested in this research.

  18. Piston rod seal for a Stirling engine

    SciTech Connect

    Shapiro, W.

    1984-01-31

    In a piston rod seal for a Stirling engine, a hydrostatic bearing and differential pressure regulating valve are utilized to provide for a low pressure differential across a rubbing seal between the hydrogen and oil so as to reduce wear on the seal. 3 figs.

  19. Dark Current and Photocurrent in Retinal Rods

    PubMed Central

    Hagins, W. A.; Penn, R. D.; Yoshikami, S.

    1970-01-01

    The interstitial voltages, currents, and resistances of the receptor layer of the isolated rat retina have been investigated with arrays of micropipette electrodes inserted under direct visual observation by infrared microscopy. In darkness a steady current flows inward through the plasma membrane of the rod outer segments. It is balanced by equal outward current distributed along the remainder of each rod. Flashes of light produce a photocurrent which transiently reduces the dark current with a waveform resembling the PII and a-wave components of the electroretinogram. The photocurrent is produced by a local action of light within 12 μm of its point of absorption in the outer segments. The quantum current gain of the photocurrent is greater than 106. The electrical space constant of rat rods is greater than 25 μm, so that the electrical effects of the photocurrent are large enough at the rod synapses to permit single absorbed photons to be detected by the visual system. The photocurrent is apparently the primary sensory consequence of light absorption by rhodopsin. ImagesFigure 3Figure 8Figure 14 PMID:5439318

  20. CONTROL ROD ALLOY CONTAINING NOBLE METAL ADDITIONS

    DOEpatents

    Anderson, W.K.; Ray, W.E.

    1960-05-01

    Silver-base alloys suitable for use in the fabrication of control rods for neutronic reactors are given. The alloy consists of from 0.5 wt.% to about 1.5 wt.% of a noble metal of platinum, ruthenium, rhodium, osmium, or palladium, up to 10 wt.% of cadmium, from 2 to 20 wt.% indium, the balance being silver.

  1. Image analysis for measuring rod network properties

    NASA Astrophysics Data System (ADS)

    Kim, Dongjae; Choi, Jungkyu; Nam, Jaewook

    2015-12-01

    In recent years, metallic nanowires have been attracting significant attention as next-generation flexible transparent conductive films. The performance of films depends on the network structure created by nanowires. Gaining an understanding of their structure, such as connectivity, coverage, and alignment of nanowires, requires the knowledge of individual nanowires inside the microscopic images taken from the film. Although nanowires are flexible up to a certain extent, they are usually depicted as rigid rods in many analysis and computational studies. Herein, we propose a simple and straightforward algorithm based on the filtering in the frequency domain for detecting the rod-shape objects inside binary images. The proposed algorithm uses a specially designed filter in the frequency domain to detect image segments, namely, the connected components aligned in a certain direction. Those components are post-processed to be combined under a given merging rule in a single rod object. In this study, the microscopic properties of the rod networks relevant to the analysis of nanowire networks were measured for investigating the opto-electric performance of transparent conductive films and their alignment distribution, length distribution, and area fraction. To verify and find the optimum parameters for the proposed algorithm, numerical experiments were performed on synthetic images with predefined properties. By selecting proper parameters, the algorithm was used to investigate silver nanowire transparent conductive films fabricated by the dip coating method.

  2. A Cambrian origin for vertebrate rods

    PubMed Central

    Asteriti, Sabrina; Grillner, Sten; Cangiano, Lorenzo

    2015-01-01

    Vertebrates acquired dim-light vision when an ancestral cone evolved into the rod photoreceptor at an unknown stage preceding the last common ancestor of extant jawed vertebrates (∼420 million years ago Ma). The jawless lampreys provide a unique opportunity to constrain the timing of this advance, as their line diverged ∼505 Ma and later displayed high-morphological stability. We recorded with patch electrodes the inner segment photovoltages and with suction electrodes the outer segment photocurrents of Lampetra fluviatilis retinal photoreceptors. Several key functional features of jawed vertebrate rods are present in their phylogenetically homologous photoreceptors in lamprey: crucially, the efficient amplification of the effect of single photons, measured by multiple parameters, and the flow of rod signals into cones. These results make convergent evolution in the jawless and jawed vertebrate lines unlikely and indicate an early origin of rods, implying strong selective pressure toward dim-light vision in Cambrian ecosystems. DOI: http://dx.doi.org/10.7554/eLife.07166.001 PMID:26095697

  3. Monodisperse hard rods in external potentials

    NASA Astrophysics Data System (ADS)

    Bakhti, Benaoumeur; Karbach, Michael; Maass, Philipp; Müller, Gerhard

    2015-10-01

    We consider linear arrays of cells of volume Vc populated by monodisperse rods of size σ Vc,σ =1 ,2 ,... , subject to hardcore exclusion interaction. Each rod experiences a position-dependent external potential. In one application we also examine effects of contact forces between rods. We employ two distinct methods of exact analysis with complementary strengths and different limits of spatial resolution to calculate profiles of pressure and density on mesoscopic and microscopic length scales at thermal equilibrium. One method uses density functionals and the other statistically interacting vacancy particles. The applications worked out include gravity, power-law traps, and hard walls. We identify oscillations in the profiles on a microscopic length scale and show how they are systematically averaged out on a well-defined mesoscopic length scale to establish full consistency between the two approaches. The continuum limit, realized as Vc→0 ,σ →∞ at nonzero and finite σ Vc , connects our highest-resolution results with known exact results for monodisperse rods in a continuum. We also compare the pressure profiles obtained from density functionals with the average microscopic pressure profiles derived from the pair distribution function.

  4. Piston rod seal for a Stirling engine

    DOEpatents

    Shapiro, Wilbur

    1984-01-01

    In a piston rod seal for a Stirling engine, a hydrostatic bearing and differential pressure regulating valve are utilized to provide for a low pressure differential across a rubbing seal between the hydrogen and oil so as to reduce wear on the seal.

  5. Drop Ejection From an Oscillating Rod

    NASA Technical Reports Server (NTRS)

    Wilkes, E. D.; Basaran, O. A.

    1999-01-01

    The dynamics of a drop of a Newtonian liquid that is pendant from or sessile on a solid rod that is forced to undergo time-periodic oscillations along its axis is studied theoretically. The free boundary problem governing the time evolution of the shape of the drop and the flow field inside it is solved by a method of lines using a finite element algorithm incorporating an adaptive mesh. When the forcing amplitude is small, the drop approaches a limit cycle at large times and undergoes steady oscillations thereafter. However, drop breakup is the consequence if the forcing amplitude exceeds a critical value. Over a wide range of amplitudes above this critical value, drop ejection from the rod occurs during the second oscillation period from the commencement of rod motion. Remarkably, the shape of the interface at breakup and the volume of the primary drop formed are insensitive to changes in forcing amplitude. The interface shape at times close to and at breakup is a multi-valued function of distance measured along the rod axis and hence cannot be described by recently popularized one-dimensional approximations. The computations show that drop ejection occurs without the formation of a long neck. Therefore, this method of drop formation holds promise of preventing formation of undesirable satellite droplets.

  6. Rod Control Assemblies Wear Mechanisms

    SciTech Connect

    Kaczorowski, Damien; Georges, Jean-Mary; Bec, Sandrine; Vannes, Andre-Bernard; Tonck, Andre; Vernot, Jean-Philippe

    2002-07-01

    In nuclear power plants, slender tubular components are subjected to vibrations in a PHTW environment. As a result, the two contacting surfaces, tubes and their guides undergo impact at low contact pressures. The components are usually made of stainless steel and it was found that the influence of the PHTW, combined with other actions (such as corrosion, erosion, squeeze film effect, third body effect and cavitation) leads to a particular wear of the material. Therefore, this paper aims to show that the colloidal oxides, formed on the steel surfaces in PHTW, play a principal role in the wear of the surfaces. Actually, due to the specific kinematic conditions of the contact, the flow of compacted oxides abrades the surfaces. (authors)

  7. Stimulus-evoked outer segment changes in rod photoreceptors

    NASA Astrophysics Data System (ADS)

    Zhao, Xiaohui; Thapa, Damber; Wang, Benquan; Lu, Yiming; Gai, Shaoyan; Yao, Xincheng

    2016-06-01

    Rod-dominated transient retinal phototropism (TRP) has been recently observed in freshly isolated mouse and frog retinas. Comparative confocal microscopy and optical coherence tomography revealed that the TRP was predominantly elicited from the rod outer segment (OS). However, the biophysical mechanism of rod OS dynamics is still unknown. Mouse and frog retinal slices, which displayed a cross-section of retinal photoreceptors and other functional layers, were used to test the effect of light stimulation on rod OSs. Time-lapse microscopy revealed stimulus-evoked conformational changes of rod OSs. In the center of the stimulated region, the length of the rod OS shrunk, while in the peripheral region, the rod OS swung toward the center region. Our experimental observation and theoretical analysis suggest that the TRP may reflect unbalanced rod disc-shape changes due to localized visible light stimulation.

  8. Reprogramming of adult rod photoreceptors prevents retinal degeneration

    PubMed Central

    Montana, Cynthia L.; Kolesnikov, Alexander V.; Shen, Susan Q.; Myers, Connie A.; Kefalov, Vladimir J.; Corbo, Joseph C.

    2013-01-01

    A prime goal of regenerative medicine is to direct cell fates in a therapeutically useful manner. Retinitis pigmentosa is one of the most common degenerative diseases of the eye and is associated with early rod photoreceptor death followed by secondary cone degeneration. We hypothesized that converting adult rods into cones, via knockdown of the rod photoreceptor determinant Nrl, could make the cells resistant to the effects of mutations in rod-specific genes, thereby preventing secondary cone loss. To test this idea, we engineered a tamoxifen-inducible allele of Nrl to acutely inactivate the gene in adult rods. This manipulation resulted in reprogramming of rods into cells with a variety of cone-like molecular, histologic, and functional properties. Moreover, reprogramming of adult rods achieved cellular and functional rescue of retinal degeneration in a mouse model of retinitis pigmentosa. These findings suggest that elimination of Nrl in adult rods may represent a unique therapy for retinal degeneration. PMID:23319618

  9. 5. DETAIL OF ROD MILL BASE AND CONVEYOR BELT SUPPORT, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    5. DETAIL OF ROD MILL BASE AND CONVEYOR BELT SUPPORT, EAST VIEW. - Vanadium Corporation of America (VCA) Naturita Mill, Grinding Rod Mill, 3 miles Northwest of Naturita, between Highway 141 & San Miguel River, Naturita, Montrose County, CO

  10. 11. Detail showing stay rods and westerly Samson post; view ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    11. Detail showing stay rods and westerly Samson post; view to west. Note slackness of stay rods while draw-span is closed. - Summer Street Bridge, Spanning Reserved Channel, Boston, Suffolk County, MA

  11. Evaluation of rodded BWR assembly pin powers with simulate

    SciTech Connect

    Bahadir, T.; Lindahl, S. Oe.

    2012-07-01

    In the development of Studsvik's nodal code SIMULATE5, special attention has been given to the accurate description of pin powers. The code solves the multi-group diffusion or simplified P3 equations with high spatial resolution. A short description is given of the handling of material heterogeneities in the axial and radial directions - the axial re-homogenization and the radial sub-mesh model, respectively. Furthermore, two models which are of special importance in the presence of control rods, and hence on the pellet clad interaction (PCI) phenomenon, are described; the quarter-assembly thermal-hydraulic treatment and the depletion of absorber material. A numerical example for a real core shows that while the impact of the fine grained description is negligible on global parameters such as k{sub eff}, the effect on pin powers may be substantial. For a deeply inserted and highly depleted control rod, the difference in pin powers caused by neglecting the advanced models of SIMULATE5, may be as high as 15 %. (authors)

  12. 13. SOUTHEAST TO SUCKER ROD WORK BENCH AND WOODEN SUCKER ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    13. SOUTHEAST TO SUCKER ROD WORK BENCH AND WOODEN SUCKER ROD STORAGE RACKS ALONG EAST WALL OF FACTORY INTERIOR. AT THIS BENCH WORKERS RIVETED THREADED WROUGHT IRON CONNECTORS TO THE ENDS OF 20' LONG WOODEN SUCKER RODS (THE RODS WHICH EXTEND DOWNWARD IN THE WELL FROM THE GROUND SURFACE TO PISTON DISPLACEMENT PUMPS WHICH ACTUALLY ELEVATE WATER TO THE SURFACE). ROZNOR HEATER AT THE FAR RIGHT WAS ADDED CIRCA 1960. - Kregel Windmill Company Factory, 1416 Central Avenue, Nebraska City, Otoe County, NE

  13. Viscosity of concentrated suspensions of sphere/rod mixtures

    SciTech Connect

    Mor, R.; Gottlieb, M.; Graham, A.L.; Mondy, L.A.

    1996-05-01

    This paper discusses the viscosity of concentrated suspensions of sphere/rod mixtures by adopting the Thomas relations for spheres and Milliken`s for randomly oriented rods with aspect ratio of 20. The relative viscosity of a mixed suspension may now be calculated for any combination of rods (of aspect ratio 20) and spheres.

  14. CONTROL ROD DRIVE MECHANISM FOR A NUCLEAR REACTOR

    DOEpatents

    Hawke, B.C.; Liederbach, F.J.; Lones, W.

    1963-05-14

    A lead-screw-type control rod drive featuring an electric motor and a fluid motor arranged to provide a selectably alternative driving means is described. The electric motor serves to drive the control rod slowly during normal operation, while the fluid motor, assisted by an automatic declutching of the electric motor, affords high-speed rod insertion during a scram. (AEC)

  15. 21 CFR 888.3020 - Intramedullary fixation rod.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Intramedullary fixation rod. 888.3020 Section 888.3020 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ORTHOPEDIC DEVICES Prosthetic Devices § 888.3020 Intramedullary fixation rod. (a) Identification. An intramedullary fixation rod...

  16. 21 CFR 888.3020 - Intramedullary fixation rod.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Intramedullary fixation rod. 888.3020 Section 888.3020 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ORTHOPEDIC DEVICES Prosthetic Devices § 888.3020 Intramedullary fixation rod. (a) Identification. An intramedullary fixation rod...

  17. Carbon Inverse Opal Rods for Nonenzymatic Cholesterol Detection.

    PubMed

    Zhong, Qifeng; Xie, Zhuoying; Ding, Haibo; Zhu, Cun; Yang, Zixue; Gu, Zhongze

    2015-11-18

    Carbon inverse opal rods made from silica photonic crystal rods are used for nonenzymatic cholesterol sensing. The characteristic reflection peak originating from the physical periodic structure works as sensing signals for quantitatively estimating cholesterol concentrations. Carbon inverse opal rods work both in cholesterol standard solutions and human serum. They are suitable for practical use in clinical diagnose. PMID:26415111

  18. Rod Has High Tensile Strength And Low Thermal Expansion

    NASA Technical Reports Server (NTRS)

    Smith, D. E.; Everton, R. L.; Howe, E.; O'Malley, M.

    1996-01-01

    Thoriated tungsten extension rod fabricated to replace stainless-steel extension rod attached to linear variable-differential transformer in gap-measuring gauge. Threads formed on end of rod by machining with special fixtures and carefully chosen combination of speeds and feeds.

  19. Measurement of the Speed of Sound in a Metal Rod.

    ERIC Educational Resources Information Center

    Mak, Se-yuen; Ng, Yee-kong; Wu, Kam-wah

    2000-01-01

    Suggests two improved methods to measure the speed of sound in a metal rod. One employs a fast timer to measure the time required for a compression pulse to travel along the rod from end to end, and a second uses a microphone to measure the frequency of the fundamental mode of a freely suspending singing rod. (Author/ASK)

  20. Mie resonance in the arrays of dielectric rods in air

    NASA Astrophysics Data System (ADS)

    Dalal, Reena; Kalra, Yogita; Sinha, R. K.

    2015-09-01

    Mie resonance in square arrays of dielectric rods has been reported. Arrays in square lattice of dielectric rods with very high permittivity in air have been considered. Light of transverse electric mode has been launched on the square array of cylindrical dielectric rods. Mie resonance of first two orders has been observed in the dielectric rods, due to which electric and magnetic dipoles are generated in the rods. Thus, electric resonance and magnetic resonance at different frequencies has been observed with material of high value of permittivity.

  1. Variable flow control for a nuclear reactor control rod

    DOEpatents

    Carleton, Richard D.; Bhattacharyya, Ajay

    1978-01-01

    A variable flow control for a control rod assembly of a nuclear reactor that depends on turbulent friction though an annulus. The annulus is formed by a piston attached to the control rod drive shaft and a housing or sleeve fitted to the enclosure housing the control rod. As the nuclear fuel is burned up and the need exists for increased reactivity, the control rods are withdrawn, which increases the length of the annulus and decreases the rate of coolant flow through the control rod assembly.

  2. Diffusion of a nanowire rod through an obstacle field

    NASA Astrophysics Data System (ADS)

    Kasimov, Dror; Admon, Tamir; Roichman, Yael

    2016-05-01

    We report the experimental realization of a rod diffusing in a two-dimensional obstacle field following the single rod dynamics. We use a silver nanowire as our rod and two types of obstacles: repelling light beams and polymer pillars. We study the effect of hydrodynamic interactions on the transport of the rod, comparing both experimental realizations and recent simulations. We propose a framework for analyzing the transport through such systems, and we predict a new superdiffusive regime of rod transport at high obstacle concentration and short times.

  3. Rebirth of a control rod at the Phenix power plant

    SciTech Connect

    De Carvalho, Corinne; Vignau, Bernard; Masson, Marc

    2007-07-01

    This paper outlines the operations involved in cleaning the control rod for the complementary shutdown system in the Phenix Power Plant, the French sodium-cooled fast reactor. The Phenix reactor is controlled by six control rods and a complementary shutdown system. The latter comprises a control rod and a mechanism maintaining the rod in position by means of an electromagnet. The electromagnet is continuously supplied with power and holds the rod control assembly in position by magnetisation on a plane circular surface made from pure iron. The bearing capacity of the mechanism on the rod was initially 80 daN with a rod weight of 26.3 daN. This deteriorated progressively over time. The bearing surface of the rod and the electromagnet became contaminated with a deposit of sodium oxides and metallic particles, thus creating an air gap. This reached a figure of 36 daN in 2005 and was deemed not to be sufficient to prevent the rod from dropping at the wrong time during reactor operation. The Power Plant thus decided to replace the rod mechanism in the reactor in an initial phase, followed by the control rod itself. As the Phenix Power Plant had no spare control rods left, they initiated a 'salvage' plan, over two stages, for the rod removed from the reactor and placed in the fuel storage drum: - Inspection of the bearing surface of the rod by means of a borescope to check whether the rod could be salvaged, - A cleaning operation on the bearing face and checks on the bearing capacity of the rod. The operation is subject to very stringent requirements: the rod must not be taken out of the sodium to ensure that it can be reused in the reactor. The operation must thus take place in the fuel storage drum where there are no facilities for such an operation and where operating conditions are very hostile: high temperatures (the sodium in the fuel storage drum is at a temperature of 150 deg. C, high dose rate (3 mGy/h on the bearing surface) and the bearing surface is submerged

  4. Following the equilibria of slender elastic rods

    NASA Astrophysics Data System (ADS)

    Lazarus, Arnaud; Miller, James; Reis, Pedro

    2012-02-01

    We present a novel continuation method to characterize and quantify the equilibria of elastic rods under large geometrically nonlinear displacements and rotations. To describe the kinematics we exploit the synthetic power and computational efficiency of quaternions. The energetics of bending, stretching and torsion are all taken into account to derive the equilibrium equations which we solve using an asymptotic numerical continuation method. This provides access to the full set of analytical equilibrium branches (stable and unstable), a.k.a bifurcation diagrams. This is in contrast with the individual solution points attained by classic energy minimization or predictor-corrector techniques. We challenge our numerics for the specific problem of an extremely twisted naturally curved rod and perform a detailed comparison against a precision desktop-scale experiments. The quantification of the underlying 3D buckling instabilities and the characterization of the resulting complex configurations are in excellent agreement between numerics and experiments.

  5. Dynamics of gas-fluidized granular rods.

    PubMed

    Daniels, L J; Park, Y; Lubensky, T C; Durian, D J

    2009-04-01

    We study a quasi-two-dimensional monolayer of granular rods fluidized by a spatially and temporally homogeneous upflow of air. By tracking the position and orientation of the particles, we characterize the dynamics of the system with sufficient resolution to observe ballistic motion at the shortest time scales. Particle anisotropy gives rise to dynamical anisotropy and superdiffusive dynamics parallel to the rod's long axis, causing the parallel and perpendicular mean-square displacements to become diffusive on different time scales. The distributions of free times and free paths between collisions deviate from exponential behavior, underscoring the nonthermal character of the particle motion. The dynamics show evidence of rotational-translational coupling similar to that of an anisotropic Brownian particle. We model rotational-translational coupling in the single-particle dynamics with a modified Langevin model using nonthermal noise sources. This suggests a phenomenological approach to thinking about collections of self-propelling particles in terms of enhanced memory effects. PMID:19518218

  6. On the Vortex Sound from Rotating Rods

    NASA Technical Reports Server (NTRS)

    Yudin, E. Y.

    1947-01-01

    The motion of different bodies imersed in liquid or gaseous media is accompanied by characteristic sound which is excited by the formation of unstable surfaces of separation behind the body, usually disintegrating into a system of discrete vortices(such as the Karman vortex street due to the flow about an infintely long rod, etc.).In the noise from fans,pumps,and similar machtnery, vortexnQif3eI?Yequently predominates. The purpose of this work is to elucidate certain questions of the dependence ofthis sound upon the aerodynamic parameters and the tip speed of the rotating rods,or blades. Although scme material is given below,insufficientto calculate the first rough approximation to the solution of this question,such as the mechanics of vortex formation,never the less certain conclusions maybe found of practical application for the reduction of noise from rotating blades.

  7. Nuclear reactor fuel rod attachment system

    DOEpatents

    Christiansen, David W.

    1982-01-01

    A reusable system for removably attaching a nuclear reactor fuel rod (12) to a support member (14). A locking cap (22) is secured to the fuel rod (12) and a locking strip (24) is fastened to the support member (14). The locking cap (22) has two opposing fingers (24a and 24b) shaped to form a socket having a body portion (26). The locking strip has an extension (36) shaped to rigidly attach to the socket's body portion (26). The locking cap's fingers are resiliently deflectable. For attachment, the locking cap (22) is longitudinally pushed onto the locking strip (24) causing the extension (36) to temporarily deflect open the fingers (24a and 24b) to engage the socket's body portion (26). For removal, the process is reversed.

  8. Hamiltonian formulations and symmetries in rod mechanics

    SciTech Connect

    Dichmann, D.J.; Li, Yiwei; Maddocks, J.H.

    1996-12-31

    This article provides a survey of contemporary rod mechanics, including both dynamic and static theories. Much of what we discuss is regarded as classic material within the mechanics community, but the objective here is to provide a self-contained account accessible to workers interested in modelling DNA. We also describe a number of recent results and computations involving rod mechanics that have been obtained by our group at the University of Maryland. This work was largely motivated by applications to modelling DNA, but our approach reflects a background of research in continuum mechanics. In particular, we emphasize the role that Hamiltonian formulations and symmetries play in the effective computation of special solutions, conservation laws of dynamics and integrals of statics. 41 refs., 10 figs.

  9. Theory of thin-walled rods

    NASA Technical Reports Server (NTRS)

    Goldenveizer, A L

    1951-01-01

    Starting with the Love equations for bending of extensible shells, "principal stress states" are sought for a thin-walled rod of arbitrary but open cross section. Principal stress states exclude those local states arising from end conditions which damp out with distance from the ends. It is found that for rods of intermediate length, long enough to avoid local bending at a support, and short enough that elementary torsion and bending are not the most significant stress states, four principal states exist. Three of these states are associated with the planar distribution of axial stress and are equivalent to the engineering theory of extension and bending of solid sections. The fourth state resembles that which has been called in the literature "bending stress due to torsional", except that cross sections are permitted to bend and the shear along the center line of the cross section is permitted to differ from zero.

  10. [Rod of Asclepius. Symbol of medicine].

    PubMed

    Young, Pablo; Finn, Bárbara C; Bruetman, Julio E; Cesaro Gelos, Jorge; Trimarchi, Hernán

    2013-09-01

    Symbolism is one of the most archaic forms of human thoughts. Symbol derives from the Latin word symbolum, and the latter from the Greek symbolon or symballo, which means "I coincide, I make matches". The Medicine symbol represents a whole series of historical and ethical values. Asclepius Rod with one serpent entwined, has traditionally been the symbol of scientific medicine. In a misconception that has lasted 500 years, the Caduceus of Hermes, entwined by two serpents and with two wings, has been considered the symbol of Medicine. However, the Caduceus is the current symbol of Commerce. Asclepius Rod and the Caduceus of Hermes represent two professions, Medicine and Commerce that, in ethical practice, should not be mixed. Physicians should be aware of their real emblem, its historical origin and meaning. PMID:24522424

  11. Statistical properties of a folded elastic rod

    NASA Astrophysics Data System (ADS)

    Bayart, Elsa; Deboeuf, Stéphanie; Boué, Laurent; Corson, Francis; Boudaoud, Arezki; Adda-Bedia, Mokhtar

    2010-03-01

    A large variety of elastic structures naturally seem to be confined into environments too small to accommodate them; the geometry of folded structures span a wide range of length-scales. The elastic properties of these confined systems are further constrained by self-avoidance as well as by the dimensionality of both structures and container. To mimic crumpled paper, we devised an experimental setup to study the packing of a dimensional elastic object in 2D geometries: an elastic rod is folded at the center of a circular Hele-Shaw cell by a centripetal force. The initial configuration of the rod and the acceleration of the rotating disk allow to span different final folded configurations while the final rotation speed controls the packing intensity. Using image analysis we measure geometrical and mechanical properties of the folded configurations, focusing on length, curvature and energy distributions.

  12. Fluid Dynamics in Sucker Rod Pumps

    SciTech Connect

    Cutler, R.P.; Mansure, A.J.

    1999-01-14

    Sucker rod pumps are installed in approximately 90% of all oil wells in the U.S. Although they have been widely used for decades, there are many issues regarding the fluid dynamics of the pump that have not been fully investigated. A project was conducted at Sandia National Laboratories to develop unimproved understanding of the fluid dynamics inside a sucker rod pump. A mathematical flow model was developed to predict pressures in any pump component or an entire pump under single-phase fluid and pumping conditions. Laboratory flow tests were conducted on instrumented individual pump components and on a complete pump to verify and refine the model. The mathematical model was then converted to a Visual Basic program to allow easy input of fluid, geometry and pump parameters and to generate output plots. Examples of issues affecting pump performance investigated with the model include the effects of viscosity, surface roughness, valve design details, plunger and valve pressure differentials, and pumping rate.

  13. A survey of laser lightning rod techniques

    NASA Technical Reports Server (NTRS)

    Barnes, Arnold A., Jr.; Berthel, Robert O.

    1991-01-01

    The work done to create a laser lightning rod (LLR) is discussed. Some ongoing research which has the potential for achieving an operational laser lightning rod for use in the protection of missile launch sites, launch vehicles, and other property is discussed. Because of the ease with which a laser beam can be steered into any cloud overhead, an LLR could be used to ascertain if there exists enough charge in the clouds to discharge to the ground as triggered lightning. This leads to the possibility of using LLRs to test clouds prior to launching missiles through the clouds or prior to flying aircraft through the clouds. LLRs could also be used to probe and discharge clouds before or during any hazardous ground operations. Thus, an operational LLR may be able to both detect such sub-critical electrical fields and effectively neutralize them.

  14. Rod Driven Frequency Entrainment and Resonance Phenomena.

    PubMed

    Salchow, Christina; Strohmeier, Daniel; Klee, Sascha; Jannek, Dunja; Schiecke, Karin; Witte, Herbert; Nehorai, Arye; Haueisen, Jens

    2016-01-01

    A controversy exists on photic driving in the human visual cortex evoked by intermittent photic stimulation. Frequency entrainment and resonance phenomena are reported for frequencies higher than 12 Hz in some studies while missing in others. We hypothesized that this might be due to different experimental conditions, since both high and low intensity light stimulation were used. However, most studies do not report radiometric measurements, which makes it impossible to categorize the stimulation according to photopic, mesopic, and scotopic vision. Low intensity light stimulation might lead to scotopic vision, where rod perception dominates. In this study, we investigated photic driving for rod-dominated visual input under scotopic conditions. Twelve healthy volunteers were stimulated with low intensity light flashes at 20 stimulation frequencies, leading to rod activation only. The frequencies were multiples of the individual alpha frequency (α) of each volunteer in the range from 0.40 to 2.30(∗)α. Three hundred and six-channel whole head magnetoencephalography recordings were analyzed in time, frequency, and spatiotemporal domains with the Topographic Matching Pursuit algorithm. We found resonance phenomena and frequency entrainment for stimulations at or close to the individual alpha frequency (0.90-1.10(∗)α) and half of the alpha frequency (0.40-0.55(∗)α). No signs of resonance and frequency entrainment phenomena were revealed around 2.00(∗)α. Instead, on-responses at the beginning and off-responses at the end of each stimulation train were observed for the first time in a photic driving experiment at frequencies of 1.30-2.30(∗)α, indicating that the flicker fusion threshold was reached. All results, the resonance and entrainment as well as the fusion effects, provide evidence for rod-dominated photic driving in the visual cortex. PMID:27588002

  15. Analysis of Double-encapsulated Fuel Rods

    SciTech Connect

    Hales, Jason Dean; Medvedev, Pavel G; Novascone, Stephen Rhead; Perez, Danielle Marie; Williamson, Richard L

    2014-09-01

    In an LWR fuel rod, the cladding encapsulates the fuel, contains fission products, and transfers heat directly to the water coolant. In some situations, it may be advantageous to separate the cladding from the coolant through use of a secondary cladding or capsule. This may be done to increase confidence that the fuel or fission products will not mix with the coolant, to provide a mechanism for controlling the rod temperature, or to place multiple experimental rodlets within a single housing. With an axisymmetric assumption, it is possible to derive closed-form expressions for the temperature profile in a fuel rod using radially-constant thermal conductivity in the fuel. This is true for both a traditional fuel-cladding rod and a double-encapsulated fuel (fuel, cladding, capsule) configuration. Likewise, it is possible to employ a fuel performance code to analyse both a traditional and a double-encapsulated fuel. In the case of the latter, two sets of gap heat transfer conditions must be imposed. In this work, we review the equations associated with radial heat transfer in a cylindrical system, present analytic and computational results for a postulated power and gas mixture history for IFA-744, and describe the analysis of the AFC-2A, 2B metallic fuel alloy experiments at the Advanced Test Reactor, including the effect of a release of fission products into the cladding-capsule gap. The computational results for these two cases were obtained using BISON, a fuel performance code under development at Idaho National Laboratory.

  16. HTGR green rod intercomparison. I. Hydrogen assay

    SciTech Connect

    Meier, M.M.; Adams, E.L.

    1981-01-01

    A /sup 252/Cf hydrogen monitor has been used to determine the hydrogen content of each of the 144 unfired (green) fuel rods being circulated in the New Brunswick Laboratory fuel measurement evaluation program. The monitor was calibrated with standards fabricated by Los Alamos Scientific Laboratory (LASL) Analytical Chemistry Group, CMB-1. Measurements were made relative to these standards and overall accuracies of +-3% were achieved.

  17. On the perfect hexagonal packing of rods

    NASA Astrophysics Data System (ADS)

    Starostin, E. L.

    2006-04-01

    In most cases the hexagonal packing of fibrous structures or rods extremizes the energy of interaction between strands. If the strands are not straight, then it is still possible to form a perfect hexatic bundle. Conditions under which the perfect hexagonal packing of curved tubular structures may exist are formulated. Particular attention is given to closed or cycled arrangements of the rods like in the DNA toroids and spools. The closure or return constraints of the bundle result in an allowable group of automorphisms of the cross-sectional hexagonal lattice. The structure of this group is explored. Examples of open helical-like and closed toroidal-like bundles are presented. An expression for the elastic energy of a perfectly packed bundle of thin elastic rods is derived. The energy accounts for both the bending and torsional stiffnesses of the rods. It is shown that equilibria of the bundle correspond to solutions of a variational problem formulated for the curve representing the axis of the bundle. The functional involves a function of the squared curvature under the constraints on the total torsion and the length. The Euler-Lagrange equations are obtained in terms of curvature and torsion and due to the existence of the first integrals the problem is reduced to the quadrature. The three-dimensional shape of the bundle may be readily reconstructed by integration of the Ilyukhin-type equations in special cylindrical coordinates. The results are of universal nature and are applicable to various fibrous structures, in particular, to intramolecular liquid crystals formed by DNA condensed in toroids or packed inside the viral capsids. International Workshop on Biopolymers: Thermodynamics, Kinetics and Mechanics of DNA, RNA and Proteins, 30.05.2005-3.06.2005, The Abdus Salam International Centre for Theoretical Physics (ICTP), Trieste, Italy.

  18. Rod Driven Frequency Entrainment and Resonance Phenomena

    PubMed Central

    Salchow, Christina; Strohmeier, Daniel; Klee, Sascha; Jannek, Dunja; Schiecke, Karin; Witte, Herbert; Nehorai, Arye; Haueisen, Jens

    2016-01-01

    A controversy exists on photic driving in the human visual cortex evoked by intermittent photic stimulation. Frequency entrainment and resonance phenomena are reported for frequencies higher than 12 Hz in some studies while missing in others. We hypothesized that this might be due to different experimental conditions, since both high and low intensity light stimulation were used. However, most studies do not report radiometric measurements, which makes it impossible to categorize the stimulation according to photopic, mesopic, and scotopic vision. Low intensity light stimulation might lead to scotopic vision, where rod perception dominates. In this study, we investigated photic driving for rod-dominated visual input under scotopic conditions. Twelve healthy volunteers were stimulated with low intensity light flashes at 20 stimulation frequencies, leading to rod activation only. The frequencies were multiples of the individual alpha frequency (α) of each volunteer in the range from 0.40 to 2.30∗α. Three hundred and six-channel whole head magnetoencephalography recordings were analyzed in time, frequency, and spatiotemporal domains with the Topographic Matching Pursuit algorithm. We found resonance phenomena and frequency entrainment for stimulations at or close to the individual alpha frequency (0.90–1.10∗α) and half of the alpha frequency (0.40–0.55∗α). No signs of resonance and frequency entrainment phenomena were revealed around 2.00∗α. Instead, on-responses at the beginning and off-responses at the end of each stimulation train were observed for the first time in a photic driving experiment at frequencies of 1.30–2.30∗α, indicating that the flicker fusion threshold was reached. All results, the resonance and entrainment as well as the fusion effects, provide evidence for rod-dominated photic driving in the visual cortex. PMID:27588002

  19. Nuclear thermionic converter. [tungsten-thorium oxide rods

    NASA Technical Reports Server (NTRS)

    Phillips, W. M.; Mondt, J. F. (Inventor)

    1977-01-01

    Efficient nuclear reactor thermionic converter units are described which can be constructed at low cost and assembled in a reactor which requires a minimum of fuel. Each converter unit utilizes an emitter rod with a fluted exterior, several fuel passages located in the bulges that are formed in the rod between the flutes, and a collector receiving passage formed through the center of the rod. An array of rods is closely packed in an interfitting arrangement, with the bulges of the rods received in the recesses formed between the bulges of other rods, thereby closely packing the nuclear fuel. The rods are constructed of a mixture of tungsten and thorium oxide to provide high power output, high efficiency, high strength, and good machinability.

  20. Measurements of lightning rod responses to nearby strikes

    NASA Astrophysics Data System (ADS)

    Moore, C. B.; Aulich, G. D.; Rison, W.

    2000-05-01

    Following Benjamin Franklin's invention of the lightning rod, based on his discovery that electrified objects could be discharged by approaching them with a metal needle in hand, conventional lightning rods in the U.S. have had sharp tips. In recent years, the role of the sharp tip in causing a lightning rod to act as a strike receptor has been questioned leading to experiments in which pairs of various sharp-tipped and blunt rods have been exposed beneath thunderclouds to determine the better strike receptor. After seven years of tests, none of the sharp Franklin rods or of the so-called “early streamer emitters” has been struck, but 12 blunt rods with tip diameters ranging from 12.7 mm to 25.4 mm have taken strikes. Our field experiments and our analyses indicate that the strike-reception probabilities of Franklin's rods are greatly increased when their tips are made moderately blunt.

  1. ELECTROMAGNETIC APPARATUS FOR MOVING A ROD

    DOEpatents

    Young, J.N.

    1957-08-20

    An electromagnetic device for moving an object in a linear path by increments is described. The device is specifically adapted for moving a neutron absorbing control rod into and out of the core of a reactor and consists essentially of an extension member made of magnetic material connected to one end of the control rod and mechanically flexible to grip the walls of a sleeve member when flexed, a magnetic sleeve member coaxial with and slidable between limit stops along the flexible extension, electromagnetic coils substantially centrally located with respect to the flexible extension to flex the extension member into gripping engagement with the sleeve member when ener gized, moving electromagnets at each end of the sleeve to attract the sleeve when energized, and a second gripping electromagnet positioned along the flexible extension at a distance from the previously mentioned electromagnets for gripping the extension member when energized. In use, the second gripping electromagnet is deenergized, the first gripping electromagnet is energized to fix the extension member in the sleeve, and one of the moving electromagnets is energized to attract the sleeve member toward it, thereby moving the control rod.

  2. Incorporation of squalene into rod outer segments

    SciTech Connect

    Keller, R.K.; Fliesler, S.J. )

    1990-08-15

    We have reported previously that squalene is the major radiolabeled nonsaponifiable lipid product derived from ({sup 3}H)acetate in short term incubations of frog retinas. In the present study, we demonstrate that newly synthesized squalene is incorporated into rod outer segments under similar in vitro conditions. We show further that squalene is an endogenous constituent of frog rod outer segment membranes; its concentration is approximately 9.5 nmol/mumol of phospholipid or about 9% of the level of cholesterol. Pulse-chase experiments with radiolabeled precursors revealed no metabolism of outer segment squalene to sterols in up to 20 h of chase. Taken together with our previous absolute rate studies, these results suggest that most, if not all, of the squalene synthesized by the frog retina is transported to rod outer segments. Synthesis of protein is not required for squalene transport since puromycin had no effect on squalene incorporation into outer segments. Conversely, inhibition of isoprenoid synthesis with mevinolin had no effect on the incorporation of opsin into the outer segment. These latter results support the conclusion that the de novo synthesis and subsequent intracellular trafficking of opsin and isoprenoid lipids destined for the outer segment occur via independent mechanisms.

  3. Interfacial phenomena in hard-rod fluids

    NASA Astrophysics Data System (ADS)

    Shundyak, K. Y.

    2004-05-01

    This thesis addresses questions of interfacial ordering in hard-rod fluids at coexistence of the isotropic and nematic phases and in their contact with simple model substrates. It is organized as follows. Chapter II provides some background information about the relation between the statistical mechanical and thermodynamical level of descriptions of bulk hard-rod fluids, as well as introduces the asymptotically exact Onsager model, and some basic facts of interfacial thermodynamics. Chapter III represents studies of the simplest free IN interface in a fluid of monodisperse Onsager hard rods. For the analysis of this system we develop an efficient perturbative method to determine the (biaxial) one-particle distribution function in inhomogeneous systems. Studies of the free planar isotropic-nematic interfaces are continued in Chapter IV, where they are considered in binary mixtures of hard rods. For sufficiently different particle shapes the bulk phase diagrams of these mixtures exhibit a triple point, where an isotropic (I) phase coexists with two nematic phases (N1 and N2) of different composition. For all explored mixtures we find that upon approach of the triple point the IN2 interface shows complete wetting by an intervening N1 film. We compute the surface tension of isotropic-nematic interfaces, and find a remarkable increase with fractionation. These studies are complemented by an analysis of bulk phase behavior and interfacial properties of nonadditive binary mixtures of thin and thick hard rods in Chapter V. The formulation of this model was motivated by recent experiments in the group of Fraden, who explored the phase behavior of a mixture of viruses with different effective diameters. In our model, species of the same types are considered as interacting with the hard-core repulsive potential, whereas the excluded volume for dissimilar rods is taken to be larger (smaller) then for the pure hard rods. Such a nonadditivity enhances (reduces) fractionation at

  4. ADF/cofilin-actin rods in neurodegenerative diseases

    PubMed Central

    Bamburg, J.R.; Bernstein, B.W.; Davis, R.C.; Flynn, K.C.; Goldsbury, C.; Jensen, J.R.; Maloney, M.T.; Marsden, I.T.; Minamide, L.S.; Pak, C.W.; Shaw, A.E.; Whiteman, I.; Wiggan, O.

    2015-01-01

    Dephosphorylation (activation) of cofilin, an actin binding protein, is stimulated by initiators of neuronal dysfunction and degeneration including oxidative stress, excitotoxic glutamate, ischemia, and soluble forms of β-amyloid peptide (Aβ). Hyperactive cofilin forms rod-shaped cofilin-saturated actin filament bundles (rods). Other proteins are recruited to rods but are not necessary for rod formation. Neuronal cytoplasmic rods accumulate within neurites where they disrupt synaptic function and are a likely cause of synaptic loss without neuronal loss, as occurs early in dementias. Different rod-inducing stimuli target distinct neuronal populations within the hippocampus. Rods form rapidly, often in tandem arrays, in response to stress. They accumulate phosphorylated tau that immunostains for epitopes present in “striated neuropil threads,” characteristic of tau pathology in Alzheimer disease (AD) brain. Thus, rods might aid in further tau modifications or assembly into paired helical filaments, the major component of neurofibrillary tangles (NFTs). Rods can occlude neurites and block vesicle transport. Some rod-inducing treatments cause an increase in secreted Aβ. Thus rods may mediate the loss of synapses, production of excess Aβ, and formation of NFTs, all of the pathological hallmarks of AD. Cofilin-actin rods also form within the nucleus of heat-shocked neurons and are cleared from cells expressing wild type huntingtin protein but not in cells expressing mutant or silenced huntingtin, suggesting a role for nuclear rods in Huntington disease (HD). As an early event in the neurodegenerative cascade, rod formation is an ideal target for therapeutic intervention that might be useful in treatment of many different neurological diseases. PMID:20088812

  5. Spherical Joint Piston and Connecting Rod Developed

    NASA Technical Reports Server (NTRS)

    1996-01-01

    Under an interagency agreement with the Department of Energy, the NASA Lewis Research Center manages a Heavy-Duty Diesel Engine Technology (HDET) research program. The overall program objectives are to reduce fuel consumption through increased engine efficiency, reduce engine exhaust emissions, and provide options for the use of alternative fuels. The program is administered with a balance of research contracts, university research grants, and focused in-house research. The Cummins Engine Company participates in the HDET program under a cost-sharing research contract. Cummins is researching and developing in-cylinder component technologies for heavy-duty diesel engines. An objective of the Cummins research is to develop technologies for a low-emissions, 55-percent thermal efficiency (LE-55) engine. The best current-production engines in this class achieve about 46-percent thermal efficiency. Federal emissions regulations are driving this technology. Regulations for heavy duty diesel engines were tightened in 1994, more demanding emissions regulations are scheduled for 1998, and another step is planned for 2002. The LE-55 engine emissions goal is set at half of the 1998 regulation level and is consistent with plans for 2002 emissions regulations. LE-55 engine design requirements to meet the efficiency target dictate a need to operate at higher peak cylinder pressures. A key technology being developed and evaluated under the Cummins Engine Company LE-55 engine concept is the spherical joint piston and connecting rod. Unlike conventional piston and connecting rod arrangements which are joined by a pin forming a hinged joint, the spherical joint piston and connecting rod use a ball-and-socket joint. The ball-and-socket arrangement enables the piston to have an axisymmetric design allowing rotation within the cylinder. The potential benefits of piston symmetry and rotation are reduced scuffing, improved piston ring sealing, improved lubrication, mechanical and thermal

  6. Between a Map and a Data Rod

    NASA Technical Reports Server (NTRS)

    Teng, William; Rui, Hualan; Strub, Richard; Vollmer, Bruce

    2015-01-01

    A Digital Divide has long stood between how NASA and other satellite-derived data are typically archived (time-step arrays or maps) and how hydrology and other point-time series oriented communities prefer to access those data. In essence, the desired method of data access is orthogonal to the way the data are archived. Our approach to bridging the Divide is part of a larger NASA-supported data rods project to enhance access to and use of NASA and other data by the Consortium of Universities for the Advancement of Hydrologic Science, Inc. (CUAHSI) Hydrologic Information System (HIS) and the larger hydrology community. Our main objective was to determine a way to reorganize data that is optimal for these communities. Two related objectives were to optimally reorganize data in a way that (1) is operational and fits in and leverages the existing Goddard Earth Sciences Data and Information Services Center (GES DISC) operational environment and (2) addresses the scaling up of data sets available as time series from those archived at the GES DISC to potentially include those from other Earth Observing System Data and Information System (EOSDIS) data archives. Through several prototype efforts and lessons learned, we arrived at a non-database solution that satisfied our objectivesconstraints. We describe, in this presentation, how we implemented the operational production of pre-generated data rods and, considering the tradeoffs between length of time series (or number of time steps), resources needed, and performance, how we implemented the operational production of on-the-fly (virtual) data rods. For the virtual data rods, we leveraged a number of existing resources, including the NASA Giovanni Cache and NetCDF Operators (NCO) and used data cubes processed in parallel. Our current benchmark performance for virtual generation of data rods is about a years worth of time series for hourly data (9,000 time steps) in 90 seconds. Our approach is a specific implementation of

  7. Between a Map and a Data Rod

    NASA Astrophysics Data System (ADS)

    Teng, W. L.; Rui, H.; Strub, R. F.; Vollmer, B.

    2015-12-01

    A "Digital Divide" has long stood between how NASA and other satellite-derived data are typically archived (time-step arrays or "maps") and how hydrology and other point-time series oriented communities prefer to access those data. In essence, the desired method of data access is orthogonal to the way the data are archived. Our approach to bridging the Divide is part of a larger NASA-supported "data rods" project to enhance access to and use of NASA and other data by the Consortium of Universities for the Advancement of Hydrologic Science, Inc. (CUAHSI) Hydrologic Information System (HIS) and the larger hydrology community. Our main objective was to determine a way to reorganize data that is optimal for these communities. Two related objectives were to optimally reorganize data in a way that (1) is operational and fits in and leverages the existing Goddard Earth Sciences Data and Information Services Center (GES DISC) operational environment and (2) addresses the scaling up of data sets available as time series from those archived at the GES DISC to potentially include those from other Earth Observing System Data and Information System (EOSDIS) data archives. Through several prototype efforts and lessons learned, we arrived at a non-database solution that satisfied our objectives/constraints. We describe, in this presentation, how we implemented the operational production of pre-generated data rods and, considering the tradeoffs between length of time series (or number of time steps), resources needed, and performance, how we implemented the operational production of on-the-fly ("virtual") data rods. For the virtual data rods, we leveraged a number of existing resources, including the NASA Giovanni Cache and NetCDF Operators (NCO) and used data cubes processed in parallel. Our current benchmark performance for virtual generation of data rods is about a year's worth of time series for hourly data (~9,000 time steps) in ~90 seconds. Our approach is a specific

  8. The ATLAS tile calorimeter ROD injector and multiplexer board

    NASA Astrophysics Data System (ADS)

    Valero, A.; Castillo, V.; Ferrer, A.; González, V.; Hernández, Y.; Higón, E.; Sanchís, E.; Solans, C.; Torres, J.; Valls, J. A.

    2011-02-01

    The ATLAS Tile Calorimeter is a sampling detector composed by cells made of iron-scintillator tiles. The calorimeter cell signals are digitized in the front-end electronics and transmitted to the Read-Out Drivers (RODs) at the first level trigger rate. The ROD receives triggered data from up to 9856 channels and provides the energy, phase and quality factor of the signals to the second level trigger. The back-end electronics is divided into four partitions containing eight RODs each. Therefore, a total of 32 RODs are used to process and transmit the data of the TileCal detector. In order to emulate the detector signals in the production and commissioning of ROD modules a board called ROD Injector and Multiplexer Board (RIMBO) was designed. In this paper, the RIMBO main functional blocks, PCB design and the different operation modes are described. It is described the crucial role of the board within the TileCal ROD test-bench in order to emulate the front-end electronics during the validation of ROD boards as well as during the evaluation of the ROD signal reconstruction algorithms. Finally, qualification and performance results for the injection operation mode obtained during the Tile Calorimeter ROD production tests are presented.

  9. DOP Test Evaluation of the Ballistic Performance of Armor Ceramics against Long Rod Penetration

    SciTech Connect

    Huang Fenglei; Zhang Liansheng

    2006-07-28

    A series of DOP tests with lateral confinement have been carried out and a linear relation between the residual penetration in RHA and the alumina thickness has been obtained. The rod configuration and the initial transient impact are the two factors that cause the gradual decrease of the differential efficiency factor (DEF) when the ceramic thickness is increased in literature. A new improved DEF definition is proposed to characterize the thick tile ceramic ballistic performance based on a more physical analysis.

  10. DOP test evaluation of the ballistic performance of armor ceramics against long rod penetration

    NASA Astrophysics Data System (ADS)

    Fenglei, Huang

    2005-07-01

    A series of DOP tests with lateral confinement has been carried out and a linear relation between the residual penetration in RHA and the alumina thickness been obtained. The rod configuration and the initial transient impact are thought to be responsible for the gradual decrease of differential efficiency factor (DEF) with the increase of ceramic thickness in literature DOP tests. A new revised DEF definition is proposed to more accurately characterize the thick tile ceramic ballistic performance on a more physically based analysis.

  11. DOP Test Evaluation of the Ballistic Performance of Armor Ceramics against Long Rod Penetration

    NASA Astrophysics Data System (ADS)

    Huang, Fenglei; Zhang, Liansheng

    2006-07-01

    A series of DOP tests with lateral confinement have been carried out and a linear relation between the residual penetration in RHA and the alumina thickness has been obtained. The rod configuration and the initial transient impact are the two factors that cause the gradual decrease of the differential efficiency factor (DEF) when the ceramic thickness is increased in literature. A new improved DEF definition is proposed to characterize the thick tile ceramic ballistic performance based on a more physical analysis.

  12. Simplified model for oblique penetration of long-rod into plates of finite thickness

    NASA Astrophysics Data System (ADS)

    Zhao, Guozhi

    A simplified calculation model describes the penetration phenomena of ricochet, embedment and perforation for long-rod penetrators impacting into homogeneous plates at various angles, and gives the profiles of craters and the bulge on the back of targets. The striking velocity range is from 900m/s to 1800m/s. The calculations for the model conform relatively well to test results.

  13. Application of fiber-reinforced plastic rods as prestressing tendons in concrete structures. Final report

    SciTech Connect

    Mattock, A.H.; Babaei, K.

    1989-08-01

    The study is concerned with the possibility of utilizing fiber-reinforced plastic rods as prestressing tendons, in place of traditional steel tendons, in elements of prestressed-concrete bridges exposed to corrosive environments. A survey was made of available information on the behavior characteristics of fiber-reinforced plastic tension elements and, in particular, those of glass-fiber-reinforced (GFR) tension elements. Also, an analytical study was made of the flexural behavior of concrete elements prestressed by GFR tendons. Based on the analytical study and on the survey of available information, an assessment is made of the impact on the design of prestressed-concrete members if GFR tendons are used. Some preliminary design recommendations are made, together with proposals for research needed before GFR prestressing tendons should be used in practice. Four GFR tendons with Con-Tech Systems anchorages were tested, the primary variable being the embedded length of the GFR rods in the anchorages. All the tendons failed by the rods pulling out of the anchorages. For embedded lengths of 15.2 in or greater, the failure loads were 90% of the advertised tendon strength of 220 ksi, or about 100% of the guaranteed tensile strength of 197 ksi (60 kN/rod).

  14. Numerical Analysis on the Head-Shape Effect for Long-Rod Normally Penetrating Concrete Target

    NASA Astrophysics Data System (ADS)

    Mu, Zhong-Cheng; Zhang, Wei; Cao, Zong-Sheng

    2009-06-01

    The deep penetration of long rods into thick target has been the focus for many decades in the terminal ballistic. Especially the study on long rods penetrating concrete targets arouses more and more attention. But the investigations of the head-shape effect to the high velocity penetration of long rod are few. In this paper, the penetration process of long rod with different head-shapes is analyzed through a series of numerical simulations. The impact velocity from subsonic velocity on the order of 10^2 m/s to hypervelocity on the order of 10^3 m/s is used. The penetration target is high strength concrete. Numerical model of concrete target adopts typical dynamic concrete damage model-RHT. The model has shown promising results for prediction of penetration depth. The projectile material is 4340 steel, Johnson-Cook model is chosen. In all the simulations presented here the material properties of projectiles and targets doesn't change. The flat-head and the ogive-head projectile are chosen. The effect of the CRH of ogive-head projectile on penetration depth is analyzed. Difference and similarity are described by the time history of penetrating velocity, acceleration and the head deformation.

  15. Visual transduction in human rod photoreceptors.

    PubMed Central

    Kraft, T W; Schneeweis, D M; Schnapf, J L

    1993-01-01

    1. Photocurrents were recorded with suction electrodes from rod photoreceptors of seven humans. 2. Brief flashes of light evoked transient outward currents of up to 20 pA. With increasing light intensity the peak response amplitude increased along an exponential saturation function. A half-saturating peak response was evoked by approximately sixty-five photoisomerizations. 3. Responses to brief dim flashes rose to a peak in about 200 ms. The waveform was roughly like the impulse response of a series of four to five low-pass filters. 4. The rising phases of the responses to flashes of increasing strength were found to fit with a biochemical model of phototransduction with an 'effective delay time' and 'characteristic time' of about 2 and 800 ms, respectively. 5. Spectral sensitivities were obtained over a wavelength range from 380 to 760 nm. The action spectrum, which peaked at 495 nm, followed the template described for photoreceptors in the macaque retina. Variation between rods in the position of the spectrum on the wavelength axis was small. 6. The scotopic luminosity function derived from human psychophysical experiments was found to agree well with the measured rod action spectrum after adjustments were made for lens absorption and photopigment self-screening in the intact eye. 7. Responses to steps of light rose monotonically to a maintained level, showing little or no relaxation. Nevertheless, the relationship between light intensity and steady-state response amplitude was shallower than that expected from simple response saturation. This is consistent with an adaptation mechanism acting on a rapid time scale. 8. Flash sensitivity fell with increasing intensities of background light according to Weber's law. Sensitivity was reduced twofold by lights evoking about 120 photoisomerizations per second. Background lights decreased the time to peak and the integration time of the flash response by up to 20%. PMID:8229828

  16. Biomechanical study comparing a new combined rod-plate system with conventional dual-rod and plate systems.

    PubMed

    Sha, Mo; Ding, Zheng-Qi; Ting, Hu S; Kang, Liang-Qi; Zhai, Wen-Liang; Liu, Hui

    2013-02-01

    Most anterior spinal instrumentation systems are designed as either a plate or dual-rod system and have corresponding limitations. Dual-rod designs may offer greater adjustability; however, this system also maintains a high profile and lacks a locking design. Plate systems are designed to be stiffer, but the fixed configuration is not adaptable to the variety of vertebral body shapes. The authors designed a new combined rod-plate system (D-rod) to overcome these limitations and compared its biomechanical performance with the conventional dual-rod and plate system. Eighteen pig spinal specimens were divided into 3 groups (6 per group). An L1 corpectomy was performed and fixed with the D-rod (group A; n=6), Z-plate (Sofamor Danek, Memphis, Tennessee) (group B; n=6), or Ventrofix (Synthes, Paoli, Pennsylvania) (group C; n=6) system. T13-L2 range of motion was measured with a 6 degrees of freedom (ie, flexion-extension, lateral bending, and axial rotation) spine simulator under pure moments of 6.0 Nm. The D-rod and Ventrofix specimens were significantly stiffer than the Z-plate specimens (P<.05) based on results obtained from lateral bending and flexion-extension tests. The D-rod and Z-plate specimens were significantly stiffer than the Ventrofix specimens (P<.05) in axial rotation. The D-rod combines the advantages of the plate and dual-rod systems, where the anterior rod exhibits the design of a low-profile locking plate, enhanced stability, and decreased interference of the surrounding vasculature. The posterior rods function in compression and distraction, and the dual-rod system offers greater adjustability and control over screw placement. The results indicate that it may provide adequate stability for anterior thoracolumbar reconstruction. PMID:23383624

  17. Nonequilibrium clustering of self-propelled rods.

    PubMed

    Peruani, Fernando; Deutsch, Andreas; Bär, Markus

    2006-09-01

    Motivated by aggregation phenomena in gliding bacteria, we study collective motion in a two-dimensional model of active, self-propelled rods interacting through volume exclusion. In simulations with individual particles, we find that particle clustering is facilitated by a sufficiently large packing fraction eta or length-to-width ratio kappa . The transition to clustering in simulations is well captured by a mean-field model for the cluster size distribution, which predicts that the transition values kappac of the aspect ratio for a fixed packing fraction eta are given by kappac=Ceta-1 where C is a constant. PMID:17025586

  18. Nonelastomeric Rod Seals for Advanced Hydraulic Systems

    NASA Technical Reports Server (NTRS)

    Hady, W. F.; Waterman, A. W.

    1976-01-01

    Advanced high temperature hydraulic system rod sealing requirements can be met by using seals made of nonelastomeric (plastic) materials in applications where elastomers do not have adequate life. Exploratory seal designs were optimized for advanced applications using machinable polyimide materials. These seals demonstrated equivalent flight hour lives of 12,500 at 350 F and 9,875 at 400 F in advanced hydraulic system simulation. Successful operation was also attained under simulated space shuttle applications; 96 reentry thermal cycles and 1,438 hours of vacuum storage. Tests of less expensive molded plastic seals indicated a need for improved materials to provide equivalent performance to the machined seals.

  19. Gas Interference in Sucker Rod Pump

    NASA Astrophysics Data System (ADS)

    Samad, Abdus

    2010-10-01

    Commonly used artificial lift or dewatering system is sucker rod pump and gas interference of the pump is the biggest issue in the oil and gas industry. Gas lock or fluid pound problems occur due to the gas interference when the pump has partially or completely unfilled plunger barrel. There are several techniques available in the form of patents to solve these problems but those techniques have positive as well as negative aspects. Some of the designs rely on the leakage and some of the designs rely on the mechanical arrangements etc to break the gas lock. The present article compares the existing gas interference handling techniques.

  20. ALLOY COMPOSITION FOR NEUTRONIC REACTOR CONTROL RODS

    DOEpatents

    Lustman, B.; Losco, E.F.; Snyder, H.J.; Eggleston, R.R.

    1963-01-22

    This invention relates to alloy compositons suitable as cortrol rod material consisting of, by weight, from 85% to 85% Ag, from 2% to 20% In, from up to 10% of Cd, from up to 5% Sn, and from up to 1.5% Al, the amount of each element employed being determined by the equation X + 2Y + 3Z + 3W + 4V = 1.4 and less, where X, Y, Z, W, and V represent the atom fractions of the elements Ag, Cd, In, Al and Sn. (AEC)

  1. Rodded shutdown system for a nuclear reactor

    DOEpatents

    Golden, Martin P.; Govi, Aldo R.

    1978-01-01

    A top mounted nuclear reactor diverse rodded shutdown system utilizing gas fed into a pressure bearing bellows region sealed at the upper extremity to an armature. The armature is attached to a neutron absorber assembly by a series of shafts and connecting means. The armature is held in an uppermost position by an electromagnet assembly or by pressurized gas in a second embodiment. Deenergizing the electromagnet assembly, or venting the pressurized gas, causes the armature to fall by the force of gravity, thereby lowering the attached absorber assembly into the reactor core.

  2. Swarming and swirling in self-propelled polar granular rods

    NASA Astrophysics Data System (ADS)

    Kudrolli, Arshad; Lumay, Geoffroy; Volfson, Dmitri; Tsimring, Lev

    2008-03-01

    We discuss the dynamics of ``self-propelled" polar rods experimentally and numerically. In the experiment, the polar motion was achieved by vibrating rods with asymmetric mass distribution. In the numerics, we postulate a driving force acting along the axis of the rod. We observe aggregation of rods at the boundaries because of the inability of rods to turn around and escape for high enough density under low noise conditions. As vibration strength and thus noise is increased, the aggregation reduces and a uniformly distributed state displaying local orientation order and swirls are observed. We observe greater than √n density fluctuations which are in a qualitative agreement with the Toner-Tu model, but this agreement should not be over-emphasized since the model is directly applicable to a nematic regime. Our findings elucidate an important and interesting interplay between the shape and the directed motion in realistic self-propelled rods which affects the phenomenology of their collective dynamics.

  3. Electric field in the vicinity of long thin conducting rods

    NASA Astrophysics Data System (ADS)

    Rezinkina, M. M.; Rezinkin, O. L.; Svetlichnaya, E. E.

    2015-09-01

    We report on the results of numerical and analytical calculations of distributions of potentials and electric fields in the vicinity of thin conducting rods that model the leader channel of lightning and lightning rods. We consider rods represented in the form of a uniformly charged filament, a conducting ellipsoid with a free charge on its surface, as well an ellipsoid or a cylinder in a uniform external electric field. The effect of parameters of conducting rods modeling the leader channel of lightning and lightning rods, as well as the region containing a space charge around the tip of the leader channel, on the distribution of potentials and field strengths are analyzed. The conditions for the propagation of the counter leader from the lightning rod are specified.

  4. Convergent synthesis of multiporphyrin light-harvesting rods

    DOEpatents

    Lindsey, Jonathan S.; Loewe, Robert S.

    2003-08-05

    The present invention provides a convergent method for the synthesis of light harvesting rods. The rods are oligomers of the formula A.sup.1 (A.sup.b+1).sub.b, wherein b is at least 1, A.sup.1 through A.sup.b+1 are covalently coupled rod segments, and each rod segment A.sup.1 through A.sup.1+b comprises a compound of the formula X.sup.1 (X.sup.m+1).sub.m wherein m is at least 1 and X.sup.1 through X.sup.m+1 are covalently coupled porphyrinic macrocycles. Light harvesting arrays and solar cells containing such light harvesting rods are also described, along with intermediates useful in such methods and rods produced by such methods.

  5. COMPUTER MODEL OF TEMPERATURE DISTRIBUTION IN OPTICALLY PUMPED LASER RODS

    NASA Technical Reports Server (NTRS)

    Farrukh, U. O.

    1994-01-01

    Managing the thermal energy that accumulates within a solid-state laser material under active pumping is of critical importance in the design of laser systems. Earlier models that calculated the temperature distribution in laser rods were single dimensional and assumed laser rods of infinite length. This program presents a new model which solves the temperature distribution problem for finite dimensional laser rods and calculates both the radial and axial components of temperature distribution in these rods. The modeled rod is either side-pumped or end-pumped by a continuous or a single pulse pump beam. (At the present time, the model cannot handle a multiple pulsed pump source.) The optical axis is assumed to be along the axis of the rod. The program also assumes that it is possible to cool different surfaces of the rod at different rates. The user defines the laser rod material characteristics, determines the types of cooling and pumping to be modeled, and selects the time frame desired via the input file. The program contains several self checking schemes to prevent overwriting memory blocks and to provide simple tracing of information in case of trouble. Output for the program consists of 1) an echo of the input file, 2) diffusion properties, radius and length, and time for each data block, 3) the radial increments from the center of the laser rod to the outer edge of the laser rod, and 4) the axial increments from the front of the laser rod to the other end of the rod. This program was written in Microsoft FORTRAN77 and implemented on a Tandon AT with a 287 math coprocessor. The program can also run on a VAX 750 mini-computer. It has a memory requirement of about 147 KB and was developed in 1989.

  6. Pultruded Rod/Overwrap Testing for Various Stitched Stringer Configurations

    NASA Technical Reports Server (NTRS)

    Leone, Frank A., Jr.

    2016-01-01

    The unidirectional carbon pultruded rod running through the tops of the stringers is a key design feature of the Pultruded Rod Efficient Unitized Structure (PRSEUS) concept as applied to aircraft fuselage structure. Reported herein are the test methods and results from a test campaign in which the strength of the rod/overwrap interface of various PRSEUS stringer configurations were characterized. The different stringer configurations included different materials and stacking sequences for the stringer overwrap and whether or not an additional layer of adhesive was included between the rod and the overwrap.

  7. Ordering stripe structures of nanoscale rods in diblock copolymer scaffolds

    NASA Astrophysics Data System (ADS)

    Chen, Kang; Ma, Yu-qiang

    2002-05-01

    We report a simulation on the formation of ordered stripe structures of nanoscale rods driven by symmetric diblock copolymer melts. Due to the preferential adsorption of one species of the diblock onto the mobile rods, the phase ordering process will couple with the movement of rods. We find that the self-assembly of rods on the copolymer scaffold produces the highly ordered nanowires of rods, and copolymer blends in turn form the well-oriented lamellar structure. This is due to the interplay among the micro-phase separating dynamics in the diblock copolymer, the wetting interaction between rods and diblock copolymer, and the nematic ordering dynamics of rods. We examine the influence of the domain size, the wetting strength, and the rod number density on the formation of such a nanoscale structure. Additionally, we indicate that the orientation of the pattern can be well controlled by external fields acting on the rods. The results suggest that our model system may provide a novel and simple way to control and design the ordering nanowire structure.

  8. On the theory of thin and thin-walled rods

    NASA Technical Reports Server (NTRS)

    Dzhanelidze, G Y

    1951-01-01

    Through the work of V. Z. Vlasov a theory of thin-walled rods has been established that is widely applicable in practice. This theory was extended by A. A. Umanski to thin-walled rods of closed profile section. The authors based their work on the concepts of the modern theory of shells. An attempt is made herein to construct a theory of thin-walled rods including the classical theory of deformation of thin rods by making use of a kinematic assumption.

  9. The evaluation of corrosion resistant rod end rolling element bearings

    SciTech Connect

    Braza, J.F.; Giuntoli, K.; Imundo, J.R.

    1998-12-31

    Recent developments on carburizing grades of stainless steels have provided new materials to produce corrosion resistant airframe control bearings. This paper presents the application of one of these new carburizing grades of stainless steel to rod end ball bearings. The outer ring of the rod end bearing is made out of carburized stainless steel, while the inner ring and balls are made out of through-hardened stainless steel. The stainless steel rod end bearings were evaluated according to various ASTM and Military specifications for performance and corrosion resistance. The stainless steel rod end bearings exceeded the performance requirements of standard rod end bearings (which are comprised of a carburized 8620 steel outer ring and 52100 steel inner ring and balls) in accordance with MIL-B-6039. The rod end bearings were evaluated in the radial fracture load, axial fracture load, and radial dynamic load tests. Also, salt spray and alternate immersion corrosion tests (ASTM B 117-85 and G 44-88, respectively) were conducted on the stainless steel rod end bearings. The stainless steel rod end bearings exhibited superior corrosion resistance to the standard 8620/52100 steel rod end bearings.

  10. Biophysical mechanism of transient retinal phototropism in rod photoreceptors

    NASA Astrophysics Data System (ADS)

    Zhao, Xiaohui; Thapa, Damber; Wang, Benquan; Gai, Shaoyan; Yao, Xincheng

    2016-03-01

    Oblique light stimulation evoked transient retinal phototropism (TRP) has been recently detected in frog and mouse retinas. High resolution microscopy of freshly isolated retinas indicated that the TRP is predominated by rod photoreceptors. Comparative confocal microscopy and optical coherence tomography (OCT) revealed that the TRP predominantly occurred from the photoreceptor outer segment (OS). However, biophysical mechanism of rod OS change is still unknown. In this study, frog retinal slices, which open a cross section of retinal photoreceptor and other functional layers, were used to test the effect of light stimulation on rod OS. Near infrared light microscopy was employed to monitor photoreceptor changes in retinal slices stimulated by a rectangular-shaped visible light flash. Rapid rod OS length change was observed after the stimulation delivery. The magnitude and direction of the rod OS change varied with the position of the rods within the stimulated area. In the center of stimulated region the length of the rod OS shrunk, while in the peripheral region the rod OS tip swung towards center region in the plane perpendicular to the incident stimulus light. Our experimental result and theoretical analysis suggest that the observed TRP may reflect unbalanced disc-shape change due to localized pigment bleaching. Further investigation is required to understand biochemical mechanism of the observed rod OS kinetics. Better study of the TRP may provide a noninvasive biomarker to enable early detection of age-related macular degeneration (AMD) and other diseases that are known to produce retinal photoreceptor dysfunctions.

  11. 75 FR 71729 - Notice of Availability of the Record of Decision (ROD) for the Tuskegee Airmen National Historic...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-24

    ... Planning, Environmental Impact Analysis, and Decision- making) the NPS announces the availability of the... National Park Service Notice of Availability of the Record of Decision (ROD) for the Tuskegee Airmen... a description of the project's background, a decision statement, synopses of other...

  12. Homogeneous cooling state of frictionless rod particles

    NASA Astrophysics Data System (ADS)

    Rubio-Largo, S. M.; Alonso-Marroquin, F.; Weinhart, T.; Luding, S.; Hidalgo, R. C.

    2016-02-01

    In this work, we report some theoretical results on granular gases consisting of frictionless 3D rods with low energy dissipation. We performed simulations on the temporal evolution of soft spherocylinders, using a molecular dynamics algorithm implemented on GPU architecture. A homogeneous cooling state for rods, where the time dependence of the system's intensive variables occurs only through a global granular temperature, has been identified. We have found a homogeneous cooling process, which is in excellent agreement with Haff's law, when using an adequate rescaling time τ(ξ), the value of which depends on the particle elongation ξ and the restitution coefficient. It was further found that scaled particle velocity distributions remain approximately Gaussian regardless of the particle shape. Similarly to a system of ellipsoids, energy equipartition between rotational and translational degrees of freedom was better satisfied as one gets closer to the elastic limit. Taking advantage of scaling properties, we have numerically determined the general functionality of the magnitude Dc(ξ), which describes the efficiency of the energy interchange between rotational and translational degrees of freedom, as well as its dependence on particle shape. We have detected a range of particle elongations (1.5 < ξ < 4.0), where the average energy transfer between the rotational and translational degrees of freedom results greater for spherocylinders than for homogeneous ellipsoids with the same aspect ratio.

  13. Laser decontamination of the radioactive lightning rods

    NASA Astrophysics Data System (ADS)

    Potiens, A. J.; Dellamano, J. C.; Vicente, R.; Raele, M. P.; Wetter, N. U.; Landulfo, E.

    2014-02-01

    Between 1970 and 1980 Brazil experienced a significant market for radioactive lightning rods (RLR). The device consists of an air terminal with one or more sources of americium-241 attached to it. The sources were used to ionize the air around them and to increase the attraction of atmospheric discharges. Because of their ineffectiveness, the nuclear regulatory authority in Brazil suspended the license for manufacturing, commerce and installation of RLR in 1989, and determined that the replaced RLR were to be collected to a centralized radioactive waste management facility for treatment. The first step for RLR treatment is to remove the radioactive sources. Though they can be easily removed, some contaminations are found all over the remaining metal scrap that must decontaminated for release, otherwise it must be treated as radioactive waste. Decontamination using various chemicals has proven to be inefficient and generates large amounts of secondary wastes. This work shows the preliminary results of the decontamination of 241Am-contaminated metal scrap generated in the treatment of radioactive lightning rods applying laser ablation. A Nd:YAG nanoseconds laser was used with 300 mJ energy leaving only a small amount of secondary waste to be treated.

  14. Sucker rod coupling with protective coating

    SciTech Connect

    Gray, K.W.

    1990-03-06

    This patent describes a coupling adapted to be used in a string of oil well sucker rods. It comprises: a cylindrical metallic cuff having a radial face at each end and internal threads for its entire length, having a resinous coating about 0.040 inches thick bonded over all of the external surfaces, the resinous coating is fused onto the metal. This patent describes a second coupling adapted to be used in a string of oil well sucker rods. It comprises: a cylindrical metallic cuff having a radial face at each end and internal threads for its entire length, having a resinous coating bonded over all of the external surfaces, the resinous coating is fused onto the metal, a distal plug within one end of the cuff, the distal plug snugly fitting the threads of one end and covering all internal surfaces, and an eyelet plug on the other end. The eyelet plug extending within the other end and covering the threads of that end and all internal surfaces.

  15. Application of polyimide actuator rod seals

    NASA Technical Reports Server (NTRS)

    Watermann, A. W.; Gay, B. F.; Robinson, E. D.; Srinath, S. K.; Nelson, W. G.

    1972-01-01

    Development of polyimide two-stage hydraulic actuator rod seals for application in high-performance aircraft was accomplished. The significant portion of the effort was concentrated on optimization of the chevron and K-section second-stage seal geometries to satisfy the requirements for operation at 450 K (350 F) with dynamic pressure loads varying between 200 psig steady-state and 1500 psig impulse cycling. Particular significance was placed on reducing seal gland dimension by efficiently utilizing the fatigue allowables of polyimide materials. Other objectives included investigation of pressure balancing techniques for first-stage polyimide rod seals for 4000 psig 450 K(350 F) environment and fabrication of a modular retainer for the two-stage combination. Seals were fabricated in 0.0254 m (1.0in.) and 0.0635 m (2.5in.) sizes and tested for structural integrity, frictional resistance, and endurance life. Test results showed that carefully designed second stages using polyimides could be made to satisfy the dynamic return pressure requirements of applications in high-performance aircraft. High wear under full system pressure indicated that further research is necessary to obtain an acceptable first-stage design. The modular retainer was successfully tested and showed potential for new actuator applications.

  16. Self-assembly of cyclic rod-coil diblock copolymers.

    PubMed

    He, Linli; Chen, Zenglei; Zhang, Ruifen; Zhang, Linxi; Jiang, Zhouting

    2013-03-01

    The phase behavior of cyclic rod-coil diblock copolymer melts is investigated by the dissipative particle dynamics simulation. In order to understand the effect of chain topological architecture better, we also study the linear rod-coil system. The comparison of the calculated phase diagrams between the two rod-coil copolymers reveals that the order-disorder transition point (χN)ODT for cyclic rod-coil diblock copolymers is always higher than that of equivalent linear rod-coil diblocks. In addition, the phase diagram for cyclic system is more "symmetrical," due to the topological constraint. Moreover, there are significant differences in the self-assembled overall morphologies and the local molecular arrangements. For example, frod = 0.5, both lamellar structures are formed while rod packing is different greatly in cyclic and linear cases. The lamellae with rods arranged coplanarly into bilayers occurs in cyclic rod-coil diblocks, while the lamellar structure with rods arranged end by end into interdigitated bilayers appears in linear counterpart. In both the lamellar phases, the domain size ratio of cyclic to linear diblocks is ranged from 0.63 to 0.70. This is attributed to that the cyclic architecture with the additional junction increases the contacts between incompatible blocks and prevents the coil chains from expanding as much as the linear cases. As frod = 0.7, the hexagonally packed cylinder is observed for cyclic rod-coil diblocks, while liquid-crystalline smectic A lamellar phase is formed in linear system. As a result, the cyclization of a linear rod-coil block copolymer can induce remarkable differences in the self-assembly behavior and also diversify its physical properties and applications greatly. PMID:23485326

  17. CONTROL ROD FOR A NUCLEAR REACTOR AND METHOD OF PREPARATION

    DOEpatents

    Hausner, H.H.

    1958-12-30

    BS>An improved control rod is presented for a nuclear reactor. This control rod is comprised of a rare earth metal oxide or rare earth metal carbide such as gadolinium oxide or gadolinium carbide, uniformly distributed in a metal matrix having a low cross sectional area of absorption for thermal neutrons, such as aluminum, beryllium, and zirconium.

  18. Bond of fiber reinforced plastic (FRP) rods to concrete

    SciTech Connect

    Al-Zahrani, M.M.; Nanni, A.; Al-Dulaijan, S.U.; Bakis, C.E.

    1996-11-01

    The bond behavior between FRP rods and concrete is one of the most important aspects to predicting the short- and long-term performance of FRP reinforced concrete structures including development and transfer length. In this research, the direct pull-out test was used to study the FRP/concrete bond behavior. This method allows measurement of the loaded- and free-end slip of the FRP rod and placement of a strain probe inside the rod to measure internal strain distribution in both axial and radial directions along the bonded length without affecting the FRP/concrete interface. Knowledge of strain distribution is necessary to study the load transfer mechanism between FRP rod and concrete. The scope of this paper include experimental results obtained with the direct pull-out test using 12.7 mm glass and carbon FRP rods with smooth and axisymmetrical deformed surfaces. The typical results are given as nominal bond and shear stress vs. free- and loaded-end slip. Experimental results obtained from strain probes used during pull-out tests are also presented as nominal bond and shear stress vs. strain. For smooth rods, friction is the main controlling factor. For deformed rods, bond tends to be controlled by strength and mechanical action of the axisymmetrical deformations rather than adhesion and friction. The strength of concrete appears to have no effect on the bond strength and failure mechanism of these particular machined FRP rods when concrete splitting is avoided.

  19. Packed rod neutron shield for fast nuclear reactors

    DOEpatents

    Eck, John E.; Kasberg, Alvin H.

    1978-01-01

    A fast neutron nuclear reactor including a core and a plurality of vertically oriented neutron shield assemblies surrounding the core. Each assembly includes closely packed cylindrical rods within a polygonal metallic duct. The shield assemblies are less susceptible to thermal stresses and are less massive than solid shield assemblies, and are cooled by liquid coolant flow through interstices among the rods and duct.

  20. On Configurational Formulations in the Director Theory of Rods

    NASA Astrophysics Data System (ADS)

    Irschik, Hans

    It is shown how the configurational laws of balance and jump for the director theory of rods can be derived as consequences of the fundamental rod laws of balance of linear, director and angular momentum, and of energy. The configura-tional relations so derived are independent from constitutive relations.

  1. Strategy Access Rods: A Hands-On Approach.

    ERIC Educational Resources Information Center

    Worthing, Bernadette; Laster, Barbara

    2002-01-01

    Describes Strategy Access Rods (SARs), balsa-wood, prism-like or rectangular rods on which a one-sentence reading strategy phrase in the first person is printed. Notes SARs serve as a visual, auditory, kinesthetic, and tactile reminder of the strategies available to developing readers. Discusses use of SARs for word recognition and comprehension.…

  2. 49 CFR 236.794 - Rod, up-and-down.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Rod, up-and-down. 236.794 Section 236.794 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION..., up-and-down. A rod used for connecting the semaphore arm to the operating mechanism of a signal....

  3. 49 CFR 236.794 - Rod, up-and-down.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Rod, up-and-down. 236.794 Section 236.794 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION..., up-and-down. A rod used for connecting the semaphore arm to the operating mechanism of a signal....

  4. 49 CFR 236.794 - Rod, up-and-down.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Rod, up-and-down. 236.794 Section 236.794 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION..., up-and-down. A rod used for connecting the semaphore arm to the operating mechanism of a signal....

  5. 49 CFR 236.794 - Rod, up-and-down.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Rod, up-and-down. 236.794 Section 236.794 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION..., up-and-down. A rod used for connecting the semaphore arm to the operating mechanism of a signal....

  6. 49 CFR 236.794 - Rod, up-and-down.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Rod, up-and-down. 236.794 Section 236.794 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION..., up-and-down. A rod used for connecting the semaphore arm to the operating mechanism of a signal....

  7. Dielectric tapered rod antennas for millimeter-wave applications

    NASA Astrophysics Data System (ADS)

    Kobayashi, S.; Mittra, R.; Lampe, R.

    1982-01-01

    Experimental results are presented for several types of tapered dielectric rod antennas of rectangular cross section investigated at 81.5 GHz. The antennas are based on Zucker's (1961) design principles for low sidelobes and maximum gain adapted to rods of rectangular cross section. The gain and beamwidth plots for the antennas tested are shown.

  8. Speeding rod recovery improves temporal resolution in the retina

    PubMed Central

    Fortenbach, Christopher R.; Kessler, Christopher; Peinado, Gabriel; Burns, Marie E.

    2015-01-01

    The temporal resolution of the visual system progressively increases with light intensity. Under scotopic conditions, temporal resolution is relatively poor, and may be limited by both retinal and cortical processes. Rod photoresponses themselves are quite slow because of the slowly deactivating biochemical cascade needed for light transduction. Here, we have used a transgenic mouse line with faster than normal rod phototransduction deactivation (RGS9-overexpressors) to test whether rod signaling to second-order retinal neurons is rate-limited by phototransduction or by other mechanisms. We compared electrical responses of individual wild-type and RGS9-overexpressing (RGS9-ox) rods to steady illumination and found that RGS9-ox rods required 2-fold brighter light for comparable activation, owing to faster G-protein deactivation. When presented with flickering stimuli, RGS9-ox rods showed greater magnitude fluctuations around a given steady-state current amplitude. Likewise, in vivo electroretinography (ERG) and whole-cell recording from OFF-bipolar, rod bipolar, and horizontal cells of RGS9-ox mice displayed larger than normal magnitude flicker responses, demonstrating an improved ability to transmit frequency information across the rod synapse. Slow phototransduction recovery therefore limits synaptic transmission of increments and decrements of light intensity across the first retinal synapse in normal retinas, apparently sacrificing temporal responsiveness for greater overall sensitivity in ambient light. PMID:25748270

  9. Direct determination of absorption anisotropy in colloidal quantum rods

    NASA Astrophysics Data System (ADS)

    Kamal, John Sundar; Gomes, Raquel; Hens, Zeger; Karvar, Masoumeh; Neyts, Kristiaan; Compernolle, Sien; Vanhaecke, Frank

    2012-01-01

    We propose a direct method to determine absorption anisotropy of colloidal quantum rods. In this method, the rods are aligned in solution by using an alternating electric field and we measure simultaneously the resulting average change in absorption. We show that a frequency window for the electric field exists in which the change in absorbance as a function of field strength can be analyzed in terms of the quantum-rod dipole moment and the absorption coefficient for light that is polarized parallel or perpendicular to the long axis of the rod. The approach is verified by measuring the absorbance change of CdSe rods at 400 nm as a function of field strength, where we demonstrate excellent agreement between experiment and theory. This enables us to propose improved values for the CdSe quantum-rod extinction coefficient. Next, we analyze CdSe/CdS dot-in-rods and find that the absorption of the first exciton transition is fully anisotropic, with a vanishing absorption coefficient for light that is polarized perpendicularly to the long axis of the rods.

  10. Trapping and sorting active granular rods

    NASA Astrophysics Data System (ADS)

    Ramaswamy, Sriram; Kumar, Nitin; Soni, Harsh; Gupta, Rahul; Sood, Ajay

    We report experiments and simulations on collective trapping in a horizontal monolayer of tapered granular rods rendered motile by mechanical vibration. A macroscopic fraction of the particles are trapped by a V-shaped obstacle if its opening angle is less than a threshold value of about 120 degrees, consistent with active Brownian simulations [PRL 108, 268307 (2012)]. the transition between trapped and untrapped states becomes sharper with increasing system size in our numerical studies. We offer a theoretical understanding of this nonequilibrium phase transition based on collective noise suppression and an analysis of fluxes. We show also that the trap can serve to separate particles based on their motility and rotational diffusivity. On leave from Dept of Physics, Indian Institute of Science.

  11. Dynamics of gas-fluidized granular rods

    NASA Astrophysics Data System (ADS)

    Daniels, L. J.; Park, Y.; Lubensky, T. C.; Durian, D. J.

    2009-04-01

    We study a quasi-two-dimensional monolayer of granular rods fluidized by a spatially and temporally homogeneous upflow of air. By tracking the position and orientation of the particles, we characterize the dynamics of the system with sufficient resolution to observe ballistic motion at the shortest time scales. Particle anisotropy gives rise to dynamical anisotropy and superdiffusive dynamics parallel to the rod’s long axis, causing the parallel and perpendicular mean-square displacements to become diffusive on different time scales. The distributions of free times and free paths between collisions deviate from exponential behavior, underscoring the nonthermal character of the particle motion. The dynamics show evidence of rotational-translational coupling similar to that of an anisotropic Brownian particle. We model rotational-translational coupling in the single-particle dynamics with a modified Langevin model using nonthermal noise sources. This suggests a phenomenological approach to thinking about collections of self-propelling particles in terms of enhanced memory effects.

  12. Electric Fuel Rod Simulator Fabrication at ORNL

    SciTech Connect

    Ott, Larry J.; McCulloch, Reg

    2004-02-04

    Commercial vendors could not supply the high-quality, highly instrumented electric fuel rod simulators (FRS) required for large thermal-hydraulic safety-oriented experiments at the Oak Ridge National Laboratory (ORNL) in the 1970s and early 1980s. Staff at ORNL designed, developed, and manufactured the simulators utilized in these safety experiments. Important FRS design requirements include (1) materials of construction, (2) test power requirements and availability, (3) experimental test objectives, (4) supporting thermal analyses, and (5) extensive quality control throughout all phases of FRS fabrication. This paper will present an overview of these requirements (design, analytics, and quality control) as practiced at ORNL to produce a durable high-quality FRS.

  13. Axial Thermal Rotation of Slender Rods

    NASA Astrophysics Data System (ADS)

    Li, Dichuan; Fakhri, Nikta; Pasquali, Matteo; Biswal, Sibani Lisa

    2011-05-01

    Axial rotational diffusion of rodlike polymers is important in processes such as microtubule filament sliding and flagella beating. By imaging the motion of small kinks along the backbone of chains of DNA-linked colloids, we produce a direct and systematic measurement of axial rotational diffusivity of rods both in bulk solution and near a wall. The measured diffusivities decrease linearly with the chain length, irrespective of the distance from a wall, in agreement with slender-body hydrodynamics theory. Moreover, the presence of small kinks does not affect the chain’s axial diffusivity. Our system and measurements provide insights into fundamental axial diffusion processes of slender objects, which encompass a wide range of entities including biological filaments and linear polymer chains.

  14. Nuclear reactor shutdown control rod assembly

    DOEpatents

    Bilibin, Konstantin

    1988-01-01

    A temperature responsive, self-actuated nuclear reactor shutdown control rod assembly 10. The upper end 18 of a lower drive line 17 fits within the lower end of an upper drive line 12. The lower end (not shown) of the lower drive line 17 is connected to a neutron absorber. During normal temperature conditions the lower drive line 17 is supported by detent means 22,26. When an overtemperature condition occurs thermal actuation means 34 urges ring 26 upwardly sufficiently to allow balls 22 to move radially outwardly thereby allowing lower drive line 17 to move downwardly toward the core of the nuclear reactor resulting in automatic reduction of the reactor powder.

  15. Electric Fuel Rod Simulator Fabrication at ORNL

    NASA Astrophysics Data System (ADS)

    Ott, Larry J.; McCulloch, Reg

    2004-02-01

    Commercial vendors could not supply the high-quality, highly instrumented electric fuel rod simulators (FRS) required for large thermal-hydraulic safety-oriented experiments at the Oak Ridge National Laboratory (ORNL) in the 1970s and early 1980s. Staff at ORNL designed, developed, and manufactured the simulators utilized in these safety experiments. Important FRS design requirements include (1) materials of construction, (2) test power requirements and availability, (3) experimental test objectives, (4) supporting thermal analyses, and (5) extensive quality control throughout all phases of FRS fabrication. This paper will present an overview of these requirements (design, analytics, and quality control) as practiced at ORNL to produce a durable high-quality FRS.

  16. Rod-shaped Nuclei at Extreme Spin and Isospin.

    PubMed

    Zhao, P W; Itagaki, N; Meng, J

    2015-07-10

    The anomalous rod shape in carbon isotopes has been investigated in the framework of the cranking covariant density functional theory, and two mechanisms to stabilize such a novel shape with respect to the bending motion, extreme spin, and isospin are simultaneously discussed for the first time in a self-consistent and microscopic way. By adding valence neutrons and rotating the system, we have found the mechanism stabilizing the rod shape; i.e., the σ orbitals (parallel to the symmetry axis) of the valence neutrons, important for the rod shape, are lowered by the rotation due to the Coriolis term. The spin and isospin effects enhance the stability of the rod-shaped configuration. This provides a strong hint that a rod shape could be realized in nuclei towards extreme spin and isospin. PMID:26207464

  17. Investigating the optical XNOR gate using plasmonic nano-rods

    NASA Astrophysics Data System (ADS)

    Akhlaghi, Majid; Kaboli, Milad

    2016-04-01

    In this paper, a coherent perfect absorption (CPA)-type XNOR gate based on plasmonic nano particle is proposed. It consists of two plasmonic nano rod arrays on top of two parallel arms with quartz substrate. The operation principle is based on the absorbable formation of a conductive path in the dielectric layer of a plasmonic nano-particles waveguide. Since the CPA efficiency depends strongly on the number of plasmonic nano-rod and the nano rod location, an efficient binary optimization method based the Particle Swarm Optimization (PSO) algorithm is used to design an optimized array of the plasmonic nano-rod in order to achieve the maximum absorption coefficient in the 'off' state and the minimum absorption coefficient in the 'on' state. In Binary PSO (BPSO), a group of birds consists a matrix with binary entries, control the presence ('1‧) or the absence ('0‧) of nano rod in the array.

  18. Thermal-recovery of modal instability in rod fiber amplifiers

    NASA Astrophysics Data System (ADS)

    Jørgensen, Mette Marie; Laurila, Marko; Noordegraaf, Danny; Alkeskjold, Thomas Tanggaard; Lægsgaard, Jesper

    2013-02-01

    We investigate the temporal dynamics of Modal instabilities (MI) in ROD fiber amplifiers using a 100 μm core rod fiber in a single-pass amplifier configuration, and we achieve ~200W of extracted output power before the onset of MI. Above the MI threshold, we investigate the temporal dynamics of beam fluctuations in both the transient and chaotic regime. We identify a set of discrete frequencies in the transient regime and a white distribution of frequencies in the chaotic regime. We test three identical rods using a multiple ramp-up procedure, where each rod is tested in three test series and thermally annealed between each test series. We find that the MI threshold degrades as it is reached multiple times, but is recovered by thermal annealing. We also find that the test history of the rods affects the temporal dynamics.

  19. Systematic parametric design/calculation of the piston rod unit

    NASA Astrophysics Data System (ADS)

    Kacani, V.

    2015-08-01

    In this article a modern and economic method for the strength calculation of the piston rod unit and its components under different operating conditions will be presented. Herefore the commercial FEA - Software will be linked with the company-owned calculation tools. The parametric user input will be followed by an automatic Pre- and Postprocessing. Afterwards the strength calculation is processed on all critical points of the piston rod connection, assisted by an extra module, based on general standards and special codes for reciprocating compressors. In this process most arrangements of the piston rod unit as well as the special geometries of the single-components (piston, piston rod and piston nut) can be considered easily. In this article the modeling of the notches, especially on the piston rod, piston as well as the piston nut will be covered in detail.

  20. Methodology of the Westinghouse dynamic rod worth measurement technique

    SciTech Connect

    Chao, Y.A.; Chapman, D.M.; Easter, M.E.; Hill, D.J.; Hoerner, J.A. ); Kurtz, P.N. )

    1992-01-01

    During zero-power physics testing, plant operations personnel use one of various techniques to measure the reactivity worth of the control rods to confirm shutdown margin. A simple and fast procedure for measuring rod worths called dynamic rod worth measurement (DRWM) has been developed at Westinghouse. This procedure was tested at the recent startups of Point Beach Nuclear Power Plant Unit 1 cycle 20 and Unit 2 cycle 18. The results of these tests show that DRWM measures rod worths with accuracy comparable to that of both boron dilution and rod bank exchange measurements. The DRWM procedure is a fast process of measuring the reactivity worth of individual banks by inserting and withdrawing the bank continuously at the maximum stepping speed without changing the boron concentration and recording the signals of the ex-core detectors.

  1. Modal Analysis for Connecting Rod of Reciprocating Mud Pump

    NASA Astrophysics Data System (ADS)

    Tong, Zhiwei; Liu, Hao; Zhu, Fengxia

    Modal analysis is an effective method to determine vibration mode shapes and weak parts of the complex mechanical system, its main purpose is to use optimal dynamics design method of mechanical structure system instead of the experience analog method. Reciprocating mud pump is the machine that transport mud or water in the process of drilling, which is an important component of the drilling equipment. In order to improve the performance of reciprocating pump and decrease the failure of the connecting rod caused by vibration during running, a modal analysis method is performed. In this paper, a three-dimensional finite-element model of connecting rod was built to provide analytical frequencies and mode shapes, then the modal distribution and vibration mode shapes for connecting rod were obtained by computing. The results showed the weakness of the connecting rod, which would provide the reference to dynamics analysis and structural optimization for connecting rod in the future.

  2. Semiconductor Quantum Rods as Single Molecule FluorescentBiological Labels

    SciTech Connect

    Fu, Aihua; Gu, Weiwei; Boussert, Benjamine; Koski, Kristie; Gerion, Daniele; Manna, Liberato; Le Gros, Mark; Larabell, Carolyn; Alivisatos, A. Paul

    2006-05-29

    In recent years, semiconductor quantum dots have beenapplied with great advantage in a wide range of biological imagingapplications. The continuing developments in the synthesis of nanoscalematerials and specifically in the area of colloidal semiconductornanocrystals have created an opportunity to generate a next generation ofbiological labels with complementary or in some cases enhanced propertiescompared to colloidal quantum dots. In this paper, we report thedevelopment of rod shaped semiconductor nanocrystals (quantum rods) asnew fluorescent biological labels. We have engineered biocompatiblequantum rods by surface silanization and have applied them fornon-specific cell tracking as well as specific cellular targeting. Theproperties of quantum rods as demonstrated here are enhanced sensitivityand greater resistance for degradation as compared to quantum dots.Quantum rods have many potential applications as biological labels insituations where their properties offer advantages over quantumdots.

  3. Influence of convection on rod spacing of eutectics

    NASA Technical Reports Server (NTRS)

    Caram, R.; Chandrasekhar, S.; Wilcox, W. R.

    1990-01-01

    This paper describes a three-dimensional numerical model to study the influence of convection on the rod-like microstructure of an eutectic system. This model is based on a central finite difference approach. By applying it, the average concentration near the solid/liquid interface of a growing rod-like eutectic was determined for eutectic compositions C(e) of 0.03, 0.05, and 0.10. Following Jackson and Hunt (1966), the average interfacial composition was converted to a change of undercooling at the interface and, finally, to spacing between the rods. The change in rod spacing with increasing intensity of convection was calculated assuming the eutectic grows at minimum interfacial undercooling. It was confirmed that an increase in convection should coarsen the microstructure (i.e., the rod spacing increases with increasing intensity of stirring).

  4. Random geometric graph description of connectedness percolation in rod systems

    NASA Astrophysics Data System (ADS)

    Chatterjee, Avik P.; Grimaldi, Claudio

    2015-09-01

    The problem of continuum percolation in dispersions of rods is reformulated in terms of weighted random geometric graphs. Nodes (or sites or vertices) in the graph represent spatial locations occupied by the centers of the rods. The probability that an edge (or link) connects any randomly selected pair of nodes depends upon the rod volume fraction as well as the distribution over their sizes and shapes, and also upon quantities that characterize their state of dispersion (such as the orientational distribution function). We employ the observation that contributions from closed loops of connected rods are negligible in the limit of large aspect ratios to obtain percolation thresholds that are fully equivalent to those calculated within the second-virial approximation of the connectedness Ornstein-Zernike equation. Our formulation can account for effects due to interactions between the rods, and many-body features can be partially addressed by suitable choices for the edge probabilities.

  5. A novel technique for performing symmetric Taylor impact

    NASA Astrophysics Data System (ADS)

    Walley, S. M.; Taylor, N. E.; Williamson, D. M.; Jardine, A. P.

    2015-09-01

    A novel spring tensioned wire cradle arrangement has been developed to hold the target rod lightly but firmly in place when performing rod-on-rod (symmetric Taylor) impact in a vacuum. In addition, a soft capture system has been designed and used to decelerate both rods while reducing the chance of them colliding a second time. High-speed photography was used to obtain the profile of a pure aluminium target rod as a function of time. Photon Doppler Velocimetry (PDV) was also deployed to record the velocity of the rear of the target rod as a function of time. Voiding in the interior of recovered rods was investigated non-destructively using X-ray tomography. The data provides comprehensive validation information for predictive constitutive models.

  6. Fretting wear behaviors of a dual-cooled nuclear fuel rod under a simulated rod vibration

    SciTech Connect

    Lee, Young-Ho; Kim, Hyung-Kyu; Kang, Heung-Seok; Yoon, Kyung-Ho; Kim, Jae-Yong; Lee, Kang-Hee

    2012-06-06

    Recently, a dual-cooled fuel (i.e., annular fuel) that is compatible with current operating PWR plants has been proposed in order to realize both a considerable amount of power uprating and an increase of safety margins. As the design concept should be compatible with current operating PWR plants, however, it shows a narrow gap between the fuel rods when compared with current solid nuclear fuel arrays and needs to modify the spacer grid shapes and their positions. In this study, fretting wear tests have been performed to evaluate the wear resistance of a dual-cooled fuel by using a proposed spring and dimple of spacer grids that have a cantilever type and hemispherical shape, respectively. As a result, the wear volume of the spring specimen gradually increases as the contact condition is changed from a certain gap, just contact to positive force. However, in the dimple specimen, just contact condition shows a large wear volume. In addition, a circular rod motion at upper region of contact surface is gradually increased and its diametric size depends on the wear depth increase. Based on the test results, the fretting wear resistance of the proposed spring and dimple is analyzed by comparing the wear measurement results and rod motion in detail.

  7. Fretting wear behaviors of a dual-cooled nuclear fuel rod under a simulated rod vibration

    NASA Astrophysics Data System (ADS)

    Lee, Young-Ho; Kim, Hyung-Kyu; Kang, Heung-Seok; Yoon, Kyung-Ho; Kim, Jae-Yong; Lee, Kang-Hee

    2012-06-01

    Recently, a dual-cooled fuel (i.e., annular fuel) that is compatible with current operating PWR plants has been proposed in order to realize both a considerable amount of power uprating and an increase of safety margins. As the design concept should be compatible with current operating PWR plants, however, it shows a narrow gap between the fuel rods when compared with current solid nuclear fuel arrays and needs to modify the spacer grid shapes and their positions. In this study, fretting wear tests have been performed to evaluate the wear resistance of a dual-cooled fuel by using a proposed spring and dimple of spacer grids that have a cantilever type and hemispherical shape, respectively. As a result, the wear volume of the spring specimen gradually increases as the contact condition is changed from a certain gap, just contact to positive force. However, in the dimple specimen, just contact condition shows a large wear volume. In addition, a circular rod motion at upper region of contact surface is gradually increased and its diametric size depends on the wear depth increase. Based on the test results, the fretting wear resistance of the proposed spring and dimple is analyzed by comparing the wear measurement results and rod motion in detail.

  8. Coolant mixing in LMFBR rod bundles and outlet plenum mixing transients. Progress report

    SciTech Connect

    Todreas, N.E.; Golay, M.W.; Wold, L.

    1981-02-01

    Four tasks are reported on: bundle geometry (wrapped and bare rods), subchannel geometry (bare rods), LMFBR outlet plenum flow mixing, and theoretical determination of local temperature fields in LMFBR fuel rod bundles. (DLC)

  9. Flexible growing rods: a pilot study to determine if polymer rod constructs may provide stability to skeletally immature spines

    PubMed Central

    2015-01-01

    Background Surgical treatments for early onset scoliosis (EOS), including growing rod constructs, involve many complications. Some are due to biomechanical factors. A construct that is more flexible than current instrumentation systems may reduce complications. The purpose of this preliminary study was to determine spine range of motion (ROM) after implantation of simulated growing rod constructs with a range of clinically relevant structural properties. The hypothesis was that ROM of spines instrumented with polyetheretherketone (PEEK) rods would be greater than metal rods and lower than noninstrumented controls. Further, adjacent segment motion was expected to be lower with polymer rods compared to conventional systems. Methods Biomechanical tests were conducted on 6 skeletally immature porcine thoracic spines (domestic swine, 35-40 kg). Spines were harvested after death from swine that had been utilized for other studies (IACUC approved) which had not involved the spine. Paired pedicle screws were used as anchors at proximal and distal levels. Specimens were tested under the following conditions: control, then dual rods of PEEK (6.25 mm), titanium (4 mm), and CoCr (5 mm) alloy. Lateral bending (LB) and flexion-extension (FE) moments of ±5 Nm were applied. Vertebral rotations were measured using video. Differences were determined by two-tailed t-tests and Bonferroni correction with four primary comparisons: PEEK vs control and PEEK vs CoCr, in LB and FE (α=0.05/4). Results In LB, ROM of specimens with PEEK rods was lower than control at each instrumented level. ROM was greater for PEEK rods than both Ti and CoCr at every instrumented level. Mean ROM at proximal and distal noninstrumented levels was lower for PEEK than for Ti and CoCr. In FE, mean ROM at proximal and distal noninstrumented levels was lower for PEEK than for metal. Combining treated levels, in LB, ROM for PEEK rods was 35% of control (p<0.0001) and 270% of CoCr rods (p<0.01). In FE, ROM with PEEK

  10. Simulation study on the structure of rod-coil-rod triblock copolymer and nanoparticle mixture within slit.

    PubMed

    Huang, Jian-Hua; Fan, Zhong-Xiang; Luo, Meng-Bo

    2013-11-28

    Self-assembly structures of rod-coil-rod ABA triblock copolymer and nanoparticle mixture within a slit are simulated by dissipative particle dynamics method. Results show that the structures are dependent on the rigidity of the rod block kθ, the interaction between the rod block and slit a(wA), the fraction of rod block f(A), and the slit height H. With an increase in kθ, we observe a transition from parallel lamellae to hexagonal cylinders. While with the increase in a(wA), the parallel lamellae at small kθ and hexagonal cylinders at large kθ change to perpendicular lamellae at large a(wA) close to a(As). At last, we present a phase diagram of structure with respect to f(A) and H at large kθ. PMID:24289376

  11. Interaction of Failed Fuel Rods Under Air Ingress Conditions

    SciTech Connect

    Hozer, Zoltan; Windberg, Peter; Nagy, Imre; Maroti, Laszlo; Matus, Lajos; Horvath, Marta; Csordas, Anna Pinter; Balasko, Marton; Czitrovszky, Aladar; Jani, Peter

    2003-03-15

    In the late phase of a severe reactor accident, the molten corium interacts with the vessel wall, and it can lead to the failure of the lower head. Through the failed bottom wall, part of the corium can flow into the cavity, and air can enter the primary circuit. The residual fuel in the core periphery will be further oxidized in air atmosphere. The degradation process will accelerate, and new chemical species will be formed, which can have an impact on the release of radioactive materials.Two experiments were carried out with electrically heated nine-rod pressurized water reactor-type bundles in the CODEX (COre Degradation EXperiment) facility to provide experimental data on the behavior of real fuel bundles under air oxidation conditions. The main objective of the tests was the investigation of oxidation phenomena, and some other important aspects (e.g., enhanced fission product release) were not addressed.The CODEX air ingress tests indicated the acceleration of oxidation phenomena and core degradation processes during the late phase of the vessel melt through accident, when air can have access to the residual fuel bundles in the reactor core. The degradation process was accompanied with zirconium-nitride formation and release of uranium-rich aerosols.

  12. Preliminary Study on Water Filled Tank Perforation by Rod Projectiles

    NASA Astrophysics Data System (ADS)

    Xiao, Xin-Ke; Guo, Zi-Tao; Mu, Zhong-Cheng; Zhang, Wei

    2009-06-01

    The effects of fluid structure interactions resulting from the impact of a fluid filled tank is of the interests for engineers from both the military and civilian field, where hydrodynamic-ram (HRAM) phenomena is well known. And it is believed HRAM is responsible for the vulnerability and the possible catastrophic failure of the whole tank. Thus HRAM is related to the majority concerns on this topic, where the targets were usually assumed to be thin. In order to investigate the influence of water on the crashworthiness of a tank with relatively thick walls, 3 ballistic shots on the water filled tank with two 3 mm 2A12 aluminum plates as front and back target and 4 shots on the tank without any water by 12.7 mm rods were conducted. The failure patterns were indentified from the tests and the difference in the failure mechanism was further studied by a series of detailed numerical simulations on the corresponding tests in hydro-code AUTODYN-2D by using both the coupled Lagrange-Euler technology and the SPH method. And also, the challenge of numerical simulation in this field is addressed.

  13. 76 FR 20435 - Notice of Approval of the Supplemental Finding of No Significant Impact and Record of Decision...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-12

    ... Supplemental Finding ] of No Significant Impact/Record of Decision (FONSI/ROD) for the Supplemental.... The Supplemental FONSI/ROD provides final agency determinations and approvals for the proposed...). SUPPLEMENTARY INFORMATION: The Supplemental FONSI/ROD is for the approval of actions for proposed changes to...

  14. Anisotropy in CdSe quantum rods

    SciTech Connect

    Li, Liang-shi

    2003-09-01

    The size-dependent optical and electronic properties of semiconductor nanocrystals have drawn much attention in the past decade, and have been very well understood for spherical ones. The advent of the synthetic methods to make rod-like CdSe nanocrystals with wurtzite structure has offered us a new opportunity to study their properties as functions of their shape. This dissertation includes three main parts: synthesis of CdSe nanorods with tightly controlled widths and lengths, their optical and dielectric properties, and their large-scale assembly, all of which are either directly or indirectly caused by the uniaxial crystallographic structure of wurtzite CdSe. The hexagonal wurtzite structure is believed to be the primary reason for the growth of CdSe nanorods. It represents itself in the kinetic stabilization of the rod-like particles over the spherical ones in the presence of phosphonic acids. By varying the composition of the surfactant mixture used for synthesis we have achieved tight control of the widths and lengths of the nanorods. The synthesis of monodisperse CdSe nanorods enables us to systematically study their size-dependent properties. For example, room temperature single particle fluorescence spectroscopy has shown that nanorods emit linearly polarized photoluminescence. Theoretical calculations have shown that it is due to the crossing between the two highest occupied electronic levels with increasing aspect ratio. We also measured the permanent electric dipole moment of the nanorods with transient electric birefringence technique. Experimental results on nanorods with different sizes show that the dipole moment is linear to the particle volume, indicating that it originates from the non-centrosymmetric hexagonal lattice. The elongation of the nanocrystals also results in the anisotropic inter-particle interaction. One of the consequences is the formation of liquid crystalline phases when the nanorods are dispersed in solvent to a high enough

  15. System for fuel rod removal from a reactor module

    DOEpatents

    Matchett, R.L.; Fodor, G.; Kikta, T.J.; Bacvinsicas, W.S.; Roof, D.R.; Nilsen, R.J.; Wilczynski, R.

    1988-07-28

    A robotic system for remote underwater withdrawal of the fuel rods from fuel modules of a light water breeder reactor includes a collet/grapple assembly for gripping and removing fuel rods in each module, which is positioned by use of a winch and a radial support means attached to a vertical support tube which is mounted over the fuel module. A programmable logic controller in conjunction with a microcomputer, provides control for the accurate positioning and pulling force of the rod grapple assembly. Closed circuit television cameras are provided which aid in operator interface with the robotic system. 7 figs.

  16. System for fuel rod removal from a reactor module

    DOEpatents

    Matchett, Richard L.; Roof, David R.; Kikta, Thomas J.; Wilczynski, Rosemarie; Nilsen, Roy J.; Bacvinskas, William S.; Fodor, George

    1990-01-01

    A robotic system for remote underwater withdrawal of the fuel rods from fuel modules of a light water breeder reactor includes a collet/grapple assembly for gripping and removing fuel rods in each module, which is positioned by use of a winch and a radial support means attached to a vertical support tube which is mounted over the fuel module. A programmable logic controller in conjunction with a microcomputer, provides control for the accurate positioning and pulling force of the rod grapple assembly. Closed circuit television cameras are provided which aid in operator interface with the robotic system.

  17. 26. A typical outer rod room, or rack room, showing ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    26. A typical outer rod room, or rack room, showing the racks for the nine horizontal control rods (HCRs) that would be inserted or withdrawn from the pile to control the rate of reaction. In this case, it is the 105-F Reactor in February 1945. The view is looking away from the pile, which is out of the picture on the left. Several of the cooling water hose reels for the rods can be seen at the end of the racks near the wall. D-8323 - B Reactor, Richland, Benton County, WA

  18. Connecting rod for internal combustion engine and method of manufacture

    SciTech Connect

    Machida, I.; Sato, Y.; Yamada, Y.

    1989-05-09

    A connecting rod is described for an internal combustion engine having a crankshaft axis and a piston axis the connecting rod comprising: a pair of flanges disposed in parallel relation with a plane including the crankshaft axis and the piston pin axis, each flange having a body and edges, each edge having a lateral rounded projection thereon, such that the edges are thicker than the body; and a web connecting the pair of flanges together, the web and flanges thereby forming a rod portion having a generally I-shaped section.

  19. COAXIAL CONTROL ROD DRIVE MECHANISM FOR NEUTRONIC REACTORS

    DOEpatents

    Fox, R.J.; Oakes, L.C.

    1959-04-14

    A drive mechanism is presented for the control rod or a nuclear reactor. In this device the control rod is coupled to a drive shaft which extends coaxially through the rotor of an electric motor for relative rotation with respect thereto. A gear reduction mehanism is coupled between the rotor and the drive shaft to convert the rotary motion of the motor into linear motion of the shaft with a comparatively great reduction in speed, thereby providing relatively glow linear movement of the shaft and control rod for control purposes.

  20. Fluorescent colloidal silica rods - synthesis and phase behavior

    NASA Astrophysics Data System (ADS)

    Kuijk, A.

    2012-01-01

    Although the experimental study of spherical colloids has been extensive, similar studies on rod-like particles are rare because suitable model systems are scarce. To fulfill this need, we present the synthesis of monodisperse rod-like silica colloids with tunable dimensions. Rods were produced with diameters of 200 nm and larger and lengths up to 10 µm, which resulted in aspect ratios ranging from 1 to 25. The growth mechanism of these rods involves emulsion droplets of water in pentanol, inside which silica condensation takes place. Since the silica nucleus is attached to the water/pentanol interface, the supply of reactants to the nucleus is anisotropic, causing it to grow on one side only, which results in rod formation. The rods were made suitable for quantitative real-space studies by confocal laser scanning microscopy. Several methods of fluorescent labeling are presented that resulted in constant fluorescence levels, gradients from one rod-end to the other, and even patterns of two colors. Single particle imaging was achieved by creating core-shell rods that had a fluorescent core and a non-fluorescent shell. Alternatively, the rods could be dispersed in a solvent with a low dielectric constant to induce micron-sized double layers. To enable quantitative measurements, a tracking algorithm was developed that identifies the rods' positions and orientations. The newly developed model system was used to study the phase behavior of rods. By combining real-space confocal laser scanning microscopy and small angle X-ray scattering methods, a phase diagram depending on concentration and aspect ratio was constructed, which shows good qualitative agreement with simulation results in literature. This phase diagram includes nematic and smectic phases for the higher aspect ratios. Also, the effect of external fields (electric fields, shear and templates) on the phase behavior was studied. In an electric field, rods aligned themselves with the applied field due to an

  1. Rod gripper, changer, and storage system

    NASA Technical Reports Server (NTRS)

    Benson, Mark; Demi, Todd; Mcneill, Robert; Waldo, Keith; Afghan, Alex; Oliver, Jim

    1989-01-01

    A rod changer and storage design is presented for the lunar deep drill apparatus to be used in conjunction with the Skitter walking platform. The design must take into account all of the lunar environment and working conditions. Some of these are: (1) the moon has one sixth the gravity of earth; (2) temperature gradients can range from about -170 to 265 C; (3) because of the high transportation costs, the design must be as light as possible; and (4) the process must be remotely operated (from earth or satellite) and must be automated. Because of Skitter's multiple degree of freedom movement, the design will utilize Skitter's movement to locate an implement and transport it from the rack to the drill string. The implement will be gripped by a thumb and two finger device, identified through an electronic sensing device on the thumb, and transported from the rack to the footplate and back from the footplate to the rack. The major designs discussed in this report have been broken down into three major areas: (1) gripper design (linear transport mechanism); (2) indexing system; and (3) rack design.

  2. Chiral effects in uniformly loaded rods

    NASA Astrophysics Data System (ADS)

    Ieşan, D.

    2010-09-01

    Examples of chiral materials include some auxetic materials, bones, some honeycomb structures, as well as composites with inclusions. The chiral effects cannot be described within classical elasticity. In the context of the linear theory of Cosserat elastic solids, we investigate the deformation of a chiral rod subjected to tractions on the lateral surface, to body loads, and to resultant forces and moments on the ends. The work is motivated by the recent interest in the using of the Cosserat elastic solid as model for auxetic composites, carbon nanotubes and bones. The three-dimensional problem is reduced to the study of some generalized plane strain problems. New chiral effects are presented. In the case of cylinders of arbitrary cross-section, the flexure produced by a transversal force, in contrast with the case of achiral materials, is accompanied by extension and bending by terminal couples. The body loads and the tractions on the lateral surface produce extension, flexure, torsion, bending by terminal couples and a plane strain. It is shown that a uniform pressure acting on the lateral surface of a chiral circular cylinder does not produce bending effects.

  3. End-of-life nondestructive examination of Light Water Breeder Reactor fuel rods (LWBR Development Program)

    SciTech Connect

    Gorscak, D.A.; Campbell, W.R.; Clayton, J.C.

    1987-10-01

    In-bundle and out-of-bundle (single rod) nondestructive examinations of Light Water Breeder Reactor fuel rods were performed. In-bundle examinations included visual examination and measurement of rod bow, rod-to-rod gaps, and rod removal forces. Out-of-bundle examinations included rod visuals and measurement of fuel rod length, diameter and ovality, cladding oxide and crud thickness, support grid induced cladding wear mark depth and volume, and fuel rod free hanging bow. The out-of-bundle examination also included ultrasonic inspection for cladding defects, neutron radiography for pellet integrity and plenum gap measurements, and gamma scans for instack axial gap screening and binary fuel stack length measurements. The measurements confirmed design predictions of fuel rod performance and provided evidence of excellent fuel rod performance for operation of Light Water Breeder Reactor to 29,047 effective full power hours (EFPH).

  4. Large-eddy simulation, fuel rod vibration and grid-to-rod fretting in pressurized water reactors

    DOE PAGESBeta

    Christon, Mark A.; Lu, Roger; Bakosi, Jozsef; Nadiga, Balasubramanya T.; Karoutas, Zeses; Berndt, Markus

    2016-06-29

    Grid-to-rod fretting (GTRF) in pressurized water reactors is a flow-induced vibration phenomenon that results in wear and fretting of the cladding material on fuel rods. GTRF is responsible for over 70% of the fuel failures in pressurized water reactors in the United States. Predicting the GTRF wear and concomitant interval between failures is important because of the large costs associated with reactor shutdown and replacement of fuel rod assemblies. The GTRF-induced wear process involves turbulent flow, mechanical vibration, tribology, and time-varying irradiated material properties in complex fuel assembly geometries. This paper presents a new approach for predicting GTRF induced fuelmore » rod wear that uses high-resolution implicit large-eddy simulation to drive nonlinear transient dynamics computations. The GTRF fluid–structure problem is separated into the simulation of the turbulent flow field in the complex-geometry fuel-rod bundles using implicit large-eddy simulation, the calculation of statistics of the resulting fluctuating structural forces, and the nonlinear transient dynamics analysis of the fuel rod. Ultimately, the methods developed here, can be used, in conjunction with operational management, to improve reactor core designs in which fuel rod failures are minimized or potentially eliminated. Furthermore, robustness of the behavior of both the structural forces computed from the turbulent flow simulations and the results from the transient dynamics analyses highlight the progress made towards achieving a predictive simulation capability for the GTRF problem.« less

  5. Force-extension curves for broken-rod macromolecules: Dramatic effects of different probing methods for two and three rods

    SciTech Connect

    Alexeev, A. V.; Maltseva, D. V.; Ivanov, V. A.; Klushin, L. I.; Skvortsov, A. M.

    2015-04-28

    We study force-extension curves of a single semiflexible chain consisting of several rigid rods connected by flexible spacers. The atomic force microscopy and laser optical or magnetic tweezers apparatus stretching these rod-coil macromolecules are discussed. In addition, the stretching by external isotropic force is analyzed. The main attention is focused on computer simulation and analytical results. We demonstrate that the force-extension curves for rod-coil chains composed of two or three rods of equal length differ not only quantitatively but also qualitatively in different probe methods. These curves have an anomalous shape for a chain of two rods. End-to-end distributions of rod-coil chains are calculated by Monte Carlo method and compared with analytical equations. The influence of the spacer’s length on the force-extension curves in different probe methods is analyzed. The results can be useful for interpreting experiments on the stretching of rod-coil block-copolymers.

  6. Dopamine modulation of rod pathway signaling by suppression of GABAC feedback to rod-driven depolarizing bipolar cells.

    PubMed

    Smith, Benjamin J; Côté, Patrice D; Tremblay, François

    2015-09-01

    Reducing signal gain in the highly sensitive rod pathway prevents saturation as background light levels increase, allowing the dark-adapted retina to encode stimuli over a range of background luminances. Dopamine release is increased during light adaptation and is generally accepted to suppress rod signaling in light-adapted retinas. However, recent research has suggested that dopamine, acting through D1 receptors, could additionally produce a sensitization of the rod pathway in dim light conditions via gamma-aminobutyric acid (GABA) type C receptors. Here, we evaluated the overall activity of the depolarizing bipolar cell (DBC) population in vivo to ensure the integrity of long-distance network interactions by quantifying the b-wave of the electroretinogram in mice. We showed that dopamine, acting through D1 receptors, reduced the amplitude and sensitivity of rod-driven DBCs during light adaptation by suppressing GABA type A receptor-mediated serial inhibition onto rod DBC GABA type C receptors. Block of D1 receptors did not suppress rod-driven DBC sensitivity when GABAA -mediated serial inhibition was blocked by gabazine, suggesting that the reduction in rod-driven DBC sensitivity in the absence of D1 receptors was due to disinhibition of serial inhibitory GABAergic circuitry rather than a direct facilitatory effect on GABA release onto rod-driven DBC GABA type C receptors. Finally, the large population of GABAergic A17 wide-field amacrine cells known to maintain reciprocal inhibition with rod DBCs could be excluded from the proposed disinhibitory circuit after treatment with 5,7-dihydroxytryptamine. PMID:26080286

  7. Preliminary Design Report for Modeling of Hydrogen Uptake in Fuel Rod Cladding During Severe Accidents

    SciTech Connect

    Siefken, Larry James

    1999-02-01

    Preliminary designs are described for models of hydrogen and oxygen uptake in fuel rod cladding during severe accidents. Calculation of the uptake involves the modeling of seven processes: (1) diffusion of oxygen from the bulk gas into the boundary layer at the external cladding surface, (2) diffusion from the boundary layer into the oxide layer, (3) diffusion from the inner surface of the oxide layer into the metallic part of the cladding, (4) uptake of hydrogen in the event that the clad-ding oxide layer is dissolved in a steam-starved region, (5) embrittlement of cladding due to hydrogen uptake, (6) cracking of cladding during quenching due to its embrittlement and (7) release of hydrogen from the cladding after cracking of the cladding. An integral diffusion method is described for calculating the diffusion processes in the cladding. Experimental results are presented that show a rapid uptake of hydrogen in the event of dissolution of the oxide layer and a rapid release of hydrogen in the event of cracking of the oxide layer. These experimental results are used as a basis for calculating the rate of hydrogen uptake and the rate of hydrogen release. The uptake of hydrogen is limited to the equilibrium solubility calculated by applying Sievert's law. The uptake of hydrogen is an exothermic reaction that accelerates the heatup of a fuel rod. An embrittlement criteria is described that accounts for hydrogen and oxygen concentration and the extent of oxidation. A design is described for implementing the models for hydrogen and oxygen uptake and cladding embrittlement into the programming framework of the SCDAP/RELAP5 code. A test matrix is described for assessing the impact of the proposed models on the calculated behavior of fuel rods in severe accident conditions. This report is a revision and reissue of the report entitled; "Preliminary Design Report for Modeling of Hydrogen Uptake in Fuel Rod Cladding During Severe Accidents."

  8. Generation of transversal envelope soliton in polymeric and wooden rods.

    PubMed

    de Billy, M; Hladky-Hennion, A C

    2014-07-01

    This paper is concerned with the probing of the transversal envelope solitons propagation in circular waveguides when a set of requirements (non-linearity and dispersion) are fulfilled in the waveguide and balanced. The basic idea is to analyze the shape of an acoustic pulse after it has traveled one or few trips through samples constituted of a rod and two ended beads. The dispersive behavior is associated to the bounded medium (rod) and the contacts between the elements of the specimens are assumed being described by non-linear Hertz' law type. The experimental data are obviously material dependent and have pointed out the existence of common properties on the formation and propagation properties of the envelope solitons whatever is the material (polymers, carbon fibers and wood) of the rods and spheres. Peculiar behaviors were also observed for specific material (woods) probably caused by the anisotropy of this kind of rod material leading to a double envelope soliton. PMID:24576600

  9. 13. View of disassembled steam engine showing cylinder, piston rod, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    13. View of disassembled steam engine showing cylinder, piston rod, parallel motion links and steam chest. - Hacienda Azucarera La Esperanza, Steam Engine & Mill, 2.65 Mi. N of PR Rt. 2 Bridge over Manati River, Manati, Manati Municipio, PR

  10. TOP OF MTR. CONTROL RODS AND GRID PLATE EMERGE FROM ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    TOP OF MTR. CONTROL RODS AND GRID PLATE EMERGE FROM REACTOR TANK. INL NEGATIVE NO. 6206. R.G. Larsen, Photographer, 6/27/1952 - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

  11. Remotely operated gripper provides vertical control rod movement

    NASA Technical Reports Server (NTRS)

    Hutter, E.; Koch, L. J.

    1968-01-01

    Remote actuation of a gripper shaft affects vertical engagement between a drive shaft and control rod. A secondary function of the gripper is to provide remote indication of positive completion of the gripping or ungripping operation.

  12. Efficiency of Hysteresis Rods in Small Spacecraft Attitude Stabilization

    PubMed Central

    Farrahi, Assal; Sanz-Andrés, Ángel

    2013-01-01

    A semiempirical method for predicting the damping efficiency of hysteresis rods on-board small satellites is presented. It is based on the evaluation of dissipating energy variation of different ferromagnetic materials for two different rod shapes: thin film and circular cross-section rods, as a function of their elongation. Based on this formulation, an optimum design considering the size of hysteresis rods, their cross section shape, and layout has been proposed. Finally, the formulation developed was applied to the case of four existing small satellites, whose corresponding in-flight data are published. A good agreement between the estimated rotational speed decay time and the in-flight data has been observed. PMID:24501579

  13. Rod shop, roof and truss detail showing older pink roof ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Rod shop, roof and truss detail showing older pink roof truss, newer pratt truss, and longitudinal, truss for overhead traveling crane - Chicago, Burlington & Quincy Railroad, Roundhouse & Shops, Broadway & Spring Streets, Aurora, Kane County, IL

  14. Process-based tolerance assessment of connecting rod machining process

    NASA Astrophysics Data System (ADS)

    Sharma, G. V. S. S.; Rao, P. Srinivasa; Surendra Babu, B.

    2016-01-01

    Process tolerancing based on the process capability studies is the optimistic and pragmatic approach of determining the manufacturing process tolerances. On adopting the define-measure-analyze-improve-control approach, the process potential capability index ( C p) and the process performance capability index ( C pk) values of identified process characteristics of connecting rod machining process are achieved to be greater than the industry benchmark of 1.33, i.e., four sigma level. The tolerance chain diagram methodology is applied to the connecting rod in order to verify the manufacturing process tolerances at various operations of the connecting rod manufacturing process. This paper bridges the gap between the existing dimensional tolerances obtained via tolerance charting and process capability studies of the connecting rod component. Finally, the process tolerancing comparison has been done by adopting a tolerance capability expert software.

  15. Damage mechanisms in uniaxial compression of single enamel rods.

    PubMed

    An, Bingbing; Wang, Raorao; Arola, Dwayne; Zhang, Dongsheng

    2015-02-01

    Enamel possesses a complex hierarchical structure, which bestows this tissue with unique mechanical properties. In this study, the mechanical behavior of single enamel rods was investigated under uniaxial compression. Numerical simulations were also performed using micromechanics models for individual enamel rods to identify the damage mechanisms contributing to the constitutive behavior. Experimental results showed that the single rods exhibited an elastic modulus ranging from 10~31 GPa, and that they undergo post-yield strain-hardening. The primary damage mode consisted of delamination within the assembly of mineral crystals. Results from numerical simulations suggest that strain localization within individual rods is responsible for the observed delamination, which is believed to arise from the non-uniform arrangement of mineral crystals. This mechanism was independent of mineral morphology and properties. The non-uniform crystal arrangement results in friction between crystals with different inclination angles and is believed to be responsible for the post-yield strain hardening behavior. PMID:25460920

  16. 9. Detail of gears and connection rod to sluice gate ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    9. Detail of gears and connection rod to sluice gate - Mississippi River 9-Foot Channel, Lock & Dam No. 1, In Mississippi River at Mississippi Boulevard, below Ford Parkway Bridge, Saint Paul, Ramsey County, MN

  17. Combustion of solid carbon rods in zero and normal gravity

    NASA Technical Reports Server (NTRS)

    Spuckler, C. M.; Kohl, F. J.; Miller, R. A.; Stearns, C. A.; Dewitt, K. J.

    1979-01-01

    In order to investigate the mechanism of carbon combustion, spectroscopic carbon rods were resistance ignited and burned in an oxygen environment in normal and zero gravity. Direct mass spectrometric sampling was used in the normal gravity tests to obtain concentration profiles of CO2, CO, and O2 as a function of distance from the carbon surface. The experimental concentrations were compared to those predicted by a stagnant film model. Zero gravity droptower tests were conducted in order to assess the effect of convection on the normal gravity combustion process. The ratio of flame diameter to rod diameter as a function of time for oxygen pressures of 5, 10, 15, and 20 psia was obtained for three different diameter rods. It was found that this ratio was inversely proportional to both the oxygen pressure and the rod diameter.

  18. 7. DETAIL VIEW UNDER BRIDGE OF CORRUGATED STEEL, BEAMS, RODS, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    7. DETAIL VIEW UNDER BRIDGE OF CORRUGATED STEEL, BEAMS, RODS, AND ABUTMENT - Price River Bridge, Spanning Price River, 760 North Street in Carbonville, 1 mile northwest of Price, Carbonville, Carbon County, UT

  19. Steam Engine for Shop, lineshaft, detail of crosshead, rod and ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Steam Engine for Shop, lineshaft, detail of crosshead, rod and flywheel - East Broad Top Railroad & Coal Company, Machine Shop, State Route 994, West of U.S. Route 522, Rockhill Furnace, Huntingdon County, PA

  20. Self-monitoring Composite Rods for Sustainable Construction

    NASA Astrophysics Data System (ADS)

    Gonilho-Pereira, Cristiana; Zdraveva, Emilija; Fangueiro, Raul; Lanceros-Mendez, S.; Jalali, Said; de Araújo, Mário

    This paper presents the development and properties assessment of braided reinforced composite rods (BCR) able to both reinforce and monitor the stress state of concrete infrastructures. The research study aims at understanding the tensile behaviour and self-monitoring ability of composite rods reinforced by a textile structure - braided structure with core reinforcement - for civil engineering applications, namely for concrete internal reinforcement, as a steel substitute, in order to improve structures safety and sustainability. Seven types of braided composite rods have been produced using an author patented technique based on a modified conventional braiding machine. The tensile properties of the braided reinforced composite rods were evaluated in order to identify the type(s) of fibre(s) to be used as core reinforcement. BCR have been tested under bending while the variation of the electrical resistance was simultaneously monitored.

  1. 14. DETAIL VIEW OF ESCAPE TRAINING TANK, SHOWING HOLDDOWN RODS, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    14. DETAIL VIEW OF ESCAPE TRAINING TANK, SHOWING HOLD-DOWN RODS, LOOKING SOUTH - U.S. Naval Submarine Base, New London Submarine Escape Training Tank, Albacore & Darter Roads, Groton, New London County, CT

  2. 28. VIEW OF OCTAGONAL SPREAD FOOTING AND HOLDDOWN RODS 1929, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    28. VIEW OF OCTAGONAL SPREAD FOOTING AND HOLD-DOWN RODS 1929, SUBMARINE ESCAPE TRAINING TANK - U.S. Naval Submarine Base, New London Submarine Escape Training Tank, Albacore & Darter Roads, Groton, New London County, CT

  3. 39. Detail view of No. 2 Furnace iron runner; rod ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    39. Detail view of No. 2 Furnace iron runner; rod or poker at right was used to unplug iron notch. - Sloss-Sheffield Steel & Iron, First Avenue North Viaduct at Thirty-second Street, Birmingham, Jefferson County, AL

  4. Dynamics of rod eutectic growth patterns in confined geometry

    NASA Astrophysics Data System (ADS)

    Şerefoǧlu, Melis; Bottin-Rousseau, S.; Akamatsu, S.; Faivre, G.

    2012-01-01

    The dynamics of rod-like eutectics are examined using a directional solidification setup, which allows real-time observation of the whole solidification front in specimens of transparent eutectic alloys -here, succinonitrile-(D)camphor. In steady-state, rod eutectic growth patterns consist of triangular arrays, more or less disturbed by topological defects. In the absence of strong convection and of crystallographic anisotropy, the long-time evolution of the pattern is dominated by "imperfections" of the system, such as misalignment of the temperature gradient, and finite-size. In this study, we present experimental results on the finite-size effects on rod eutectics and show that a rod to lamella transition takes place as a result of finite-size effect only, at a given alloy concentration.

  5. Experimental study of burnout in channels with twisted fuel rods

    NASA Astrophysics Data System (ADS)

    Bol'Shakov, V. V.; Bashkirtsev, S. M.; Kobzar', L. L.; Morozov, A. G.

    2007-05-01

    The results of experimental studies of pressure drop and critical heat flux in the models of fuel assemblies (FAs) with fuel rod simulators twisted relative to the longitudinal axis and a three-ray cross section are considered. The experimental data are compared to the results obtained with the use of techniques adopted for design calculations with fuel rod bundles of type-VVER reactors.

  6. Apparatus for injection casting metallic nuclear energy fuel rods

    DOEpatents

    Seidel, Bobby R.; Tracy, Donald B.; Griffiths, Vernon

    1991-01-01

    Molds for making metallic nuclear fuel rods are provided which present reduced risks to the environment by reducing radioactive waste. In one embodiment, the mold is consumable with the fuel rod, and in another embodiment, part of the mold can be re-used. Several molds can be arranged together in a cascaded manner, if desired, or several long cavities can be integrated in a monolithic multiple cavity re-usable mold.

  7. Double-clad nuclear-fuel safety rod

    DOEpatents

    McCarthy, W.H.; Atcheson, D.B.

    1981-12-30

    A device for shutting down a nuclear reactor during an undercooling or overpower event, whether or not the reactor's scram system operates properly. This is accomplished by double-clad fuel safety rods positioned at various locations throughout the reactor core, wherein melting of a secondary internal cladding of the rod allows the fuel column therein to shift from the reactor core to place the reactor in a subcritical condition.

  8. BWR fuel rod performance evaluation program. Final report

    SciTech Connect

    Rowland, T.C.

    1986-05-01

    The joint EPRI/GE fuel performance program, RP510-1, involved thorough preirradiation characterization of fuel used in lead test assemblies, detailed surveillance of their operation, and interim site examinations of the assemblies during reactor outages. The program originally included four GE-5 lead test assemblies operating in the Peach Bottom-2 reactor. The program was later modified to include the pressurized fuel rod test assembly in the Peach Bottom-3 reactor (RP510-2). The program modification also included extending the operation of the Peach Bottom-2 and Peach Bottom-3 lead test assembly fuel beyond normal discharge exposures. Interim site examination results following the first four cycles of operation of the Peach Bottom-2 lead test assemblies up to 35 GWd/MT and the examination of the Peach Bottom-3 pressurized test assembly at 32 GWd/MT are presented in this report. Elements of the examinations included visual examination of the fuel bundles; individual fuel rod visual examinations, rod length measurements, ultrasonic and eddy current nondestructive testing, Zircaloy cladding oxide thickness measurements and fission gas measurements. Channel measurements were made on the PB-2 Lead Test Assemblies after each of the first three operating cycles. All of the bundles were found to be in good condition. Since the pressurized test assembly contained pressurized and nonpressurized fuel rods in symmetric positions, it was possible to make direct comparisons of the fission gas release from pairs of pressurized and nonpressurized fuel rods with identical power histories. With one exception, the release was less from the pressurized fuel rod of each pair. Fuel rod power histories were calculated using new physics methods for all of the fuel rods that were punctured for fission gas release measurements. 28 refs., 41 figs., 16 tabs.

  9. Bead-rod-spring models in random flows

    NASA Astrophysics Data System (ADS)

    Plan, Emmanuel Lance Christopher Medillo, VI; Ali, Aamir; Vincenzi, Dario

    2016-08-01

    Bead-rod-spring models are the foundation of the kinetic theory of polymer solutions. We derive the diffusion equation for the probability density function of the configuration of a general bead-rod-spring model in short-correlated Gaussian random flows. Under isotropic conditions, we solve this equation analytically for the elastic rhombus model introduced by Curtiss, Bird, and Hassager [Adv. Chem. Phys. 35, 31 (1976)].

  10. Bead-rod-spring models in random flows.

    PubMed

    Plan, Emmanuel Lance Christopher Vi Medillo; Ali, Aamir; Vincenzi, Dario

    2016-08-01

    Bead-rod-spring models are the foundation of the kinetic theory of polymer solutions. We derive the diffusion equation for the probability density function of the configuration of a general bead-rod-spring model in short-correlated Gaussian random flows. Under isotropic conditions, we solve this equation analytically for the elastic rhombus model introduced by Curtiss, Bird, and Hassager [Adv. Chem. Phys. 35, 31 (1976)]. PMID:27627227

  11. Final design review of boron carbide safety rod

    SciTech Connect

    Lutz, R.N.

    1991-09-24

    The object of this paper discusses the design review of the boron carbide safety rod for the Westinghouse Savannah River Company. This paper reviewed information presented by personnel of the Savannah River Laboratory (SRL) Equipment Engineering Section, SRL Materials Technology Section and Reactor Materials Engineering and Technology. From this report, views, opinions and recommendations were made on the safety rod from materials testing to production.

  12. Horizontal displacement profiles in N Reactor horizontal control rod channels

    SciTech Connect

    Woodruff, E.M.

    1988-12-01

    One of the potential results from N Reactor graphite moderator distortion is horizontal curvature of the horizontal control rod (HCR) channels. Mockup testing has identified two possible problem scenarios resulting from such curvature: slow scram times and rod abrasion due to rubbing of the rod on the side of the channel and subsequent displacement of T-blocks that form the sides of the channels. As a result of these potential events, surveillance tools (instrumentation) to measure HCR channel horizontal displacement was recently developed. Surveillance of HCR channel 65, performed on December 11, 1987, indicated a six inch rearward displacement near the center of the channel. This approximated the displacement which mockup testing has identified as a concern with regard to T-block movement. Closed Circuit Television (CCTV) observations indicate that T-block movement has not occurred in HCR channel 65, but that there has been some rubbing of the rod on the channel sides. Review of most recent rod hot scram times indicates normal performance for HCR 65. To further evaluate this concern, horizontal deflection and CCTV surveillance was scheduled in six HCR channels surrounding HCR channel 65. Inspection of the HCR rod tip was also performed. 13 refs., 6 figs.

  13. Vibrational Power Flow Analysis of Rods and Beams

    NASA Technical Reports Server (NTRS)

    Wohlever, James Christopher; Bernhard, R. J.

    1988-01-01

    A new method to model vibrational power flow and predict the resulting energy density levels in uniform rods and beams is investigated. This method models the flow of vibrational power in a manner analogous to the flow of thermal power in a heat conduction problem. The classical displacement solutions for harmonically excited, hysteretically damped rods and beams are used to derive expressions for the vibrational power flow and energy density in the rod and beam. Under certain conditions, the power flow in these two structural elements will be shown to be proportional to the energy density gradient. Using the relationship between power flow and energy density, an energy balance on differential control volumes in the rod and beam leads to a Poisson's equation which models the energy density distribution in the rod and beam. Coupling the energy density and power flow solutions for rods and beams is also discussed. It is shown that the resonant behavior of finite structures complicates the coupling of solutions, especially when the excitations are single frequency inputs. Two coupling formulations are discussed, the first based on the receptance method, and the second on the travelling wave approach used in Statistical Energy Analysis. The receptance method is the more computationally intensive but is capable of analyzing single frequency excitation cases. The traveling wave approach gives a good approximation of the frequency average of energy density and power flow in coupled systems, and thus, is an efficient technique for use with broadband frequency excitation.

  14. Evaluation of ceramic packed-rod regenerator matrices

    NASA Technical Reports Server (NTRS)

    Lawless, W. N.; Arenz, R. W.

    1981-01-01

    An extensive evaluation of a modified cryocooler with various regenerator matrices is reported. The matrices examined are 0.015 in. diam. Pb spheres and 0.008, 0.015, and 0.030 in. diam. rods of a 0.2% SnCl2 doped ceramic labelled LS-8A. Specific heat and thermal conductivity data on these rod materials are also reported. The chronic pulverization/dusting problem common to Pb spheres was investigated. During a 1000 hr life test with 0.0008 in. diam. rods there was no degradation of the refrigerator performance, and a subsequent examination of the rods themselves revealed no evidence of breakage or pulverization. The load temperature characteristics for the rod packed regenerators were inferior to that for the Pb spheres, the effect being to shift the Pb spheres load curve up in temperature. This temperature shift was 5.0, 7.4, and 11.6K for the 0.0008, 0.015, and 0.030 in. diam. rods, respectively.

  15. Experimental and computational studies of rod-deployment mechanisms

    SciTech Connect

    Schwalbe, L.A.; Wingate, C.A.; Stofleth, J.H.; Greene, R.W.

    1996-08-01

    We describe experimental measurements and hydrocode simulations of two tests in which long (L/D=12), steel rods were accelerated laterally with charges of Detasheet-C high explosive (HE). In each test configuration, 84 rods were initially aligned parallel to one another in an array of four concentric rings. The first test had a central core of HE that dispersed the rods isotropically. The second test had a narrow, 180 degree strip of HE on one side of the assembly that focused the rods directionally. Using radiographic data taken at several milliseconds after HE initiation, we measured the dynamic distributions of the rods, and their translational velocities and tumble rates. To compare with the data, we also modeled the experiments with our smooth particle hydrocode SPHINX. Within the context of our numerical model, the hydrocode results agree satisfactorily with the test data. We include in our discussion many of the inferences and insights that our results provide to the phenomenology and performance of multimode, rod-deployment mechanisms.

  16. Total rod ERG suppression with high dose compassionate Fenretinide usage.

    PubMed

    Marmor, Michael F; Jain, Atul; Moshfeghi, Darius

    2008-11-01

    Fenretinide is a synthetic retinoid that interferes with the attachment of retinol to retinol binding protein. It may inhibit accumulation of A2E and lipofuscin, and is proposed as therapy for Stargardt disease. It is currently used for cancer therapy, and mild depression of rod function and dark adaptation is a side effect at standard dosage. We studied two youngsters (aged between 12 and 13) receiving high doses as compassionate treatment for neuroblastoma: 800 mg daily for 1 out of every 3 weeks, for roughly 2 years. Goldmann-Weekers dark adaptometry, ISCEV standard ERG and mfERG were performed, and blood was analyzed for vitamin A. Neither child complained of night blindness or showed retinal fundus abnormalities. On initial exam, dark adaptation thresholds were elevated by 3 log units, and there were no detectable rod ERG responses. However, cone responses and mfERG were normal. Retesting one subject 3 months after stopping the drug revealed normal rod thresholds (slightly delayed) and low normal rod ERG responses. Serum vitamin A levels were normal from both subjects, but there is no record of whether the samples were drawn during cycles on or off drug. Our study demonstrates that high dose Fenretinide can suppress rod function quite completely, although serum vitamin A and rod function apparently return to normal or near normal levels rapidly once the drug is stopped. It is intriguing that cone function and access to vitamin A seems largely independent of Fenretinide effects on retinol availability. PMID:18523815

  17. Fission gas release restrictor for breached fuel rod

    DOEpatents

    Kadambi, N. Prasad; Tilbrook, Roger W.; Spencer, Daniel R.; Schwallie, Ambrose L.

    1986-01-01

    In the event of a breach in the cladding of a rod in an operating liquid metal fast breeder reactor, the rapid release of high-pressure gas from the fission gas plenum may result in a gas blanketing of the breached rod and rods adjacent thereto which impairs the heat transfer to the liquid metal coolant. In order to control the release rate of fission gas in the event of a breached rod, the substantial portion of the conventional fission gas plenum is formed as a gas bottle means which includes a gas pervious means in a small portion thereof. During normal reactor operation, as the fission gas pressure gradually increases, the gas pressure interiorly of and exteriorly of the gas bottle means equalizes. In the event of a breach in the cladding, the gas pervious means in the gas bottle means constitutes a sufficient restriction to the rapid flow of gas therethrough that under maximum design pressure differential conditions, the fission gas flow through the breach will not significantly reduce the heat transfer from the affected rod and adjacent rods to the liquid metal heat transfer fluid flowing therebetween.

  18. LWR fuel rod bundle behavior under severe fuel damage conditions

    SciTech Connect

    Kuczera, B. Hagen, S.; Hofmann, P.

    1988-01-01

    Light water reactor (LWR) safety research and development activities conducted at Kernforschungszentrum Karlsruhe have recently been reorganized with a concentrated mission under the LWR safety project group. The topics treated relate mainly to severe-accident analysis research and source term assessment as well as to source term mitigation measures. A major part of the investigations concerns the early phase of a severe core meltdown accident, specifically LWR rod assembly behavior under sever fuel damage (SFD) conditions. To determine the extent of fuel rod damage, including the relocation behavior of molten reaction products, damage propagation, time-dependent H{sub 2} generation from clad oxidation, and fragmentation of oxygen-embrittled materials during cooldown and quenching, extensive out-of-pile rod bundle experiments have been initiated in the new CORA test facility. The bundle parameters, such as rod dimensions, rod pitch, and grid spacer, can be adjusted to both pressurized water reactor (PWR) and boiling water reactor (BWR) conditions. Currently, the test program consists of 15 experiments in which the influence of Inconel grid spacer, (Ag,In,Cd)-absorber rods (PWR) and of B{sub 4}C control blades (BWR) on fuel damage initiation and damage propagation are being investigated for different boundary conditions. As of June 1988, four bundle tests had been successfully carried out for PWR accident conditions.

  19. Ultrasonic Nondestructive Evaluation of Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) During Large-Scale Load Testing and Rod Push-Out Testing

    NASA Technical Reports Server (NTRS)

    Johnston, Patrick H.; Juarez, Peter D.

    2016-01-01

    The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) is a structural concept developed by the Boeing Company to address the complex structural design aspects associated with a pressurized hybrid wing body (HWB) aircraft configuration. The HWB has long been a focus of NASA's environmentally responsible aviation (ERA) project, following a building block approach to structures development, culminating with the testing of a nearly full-scale multi-bay box (MBB), representing a segment of the pressurized, non-circular fuselage portion of the HWB. PRSEUS is an integral structural concept wherein skins, frames, stringers and tear straps made of variable number of layers of dry warp-knit carbon-fiber stacks are stitched together, then resin-infused and cured in an out-of-autoclave process. The PRSEUS concept has the potential for reducing the weight and cost and increasing the structural efficiency of transport aircraft structures. A key feature of PRSEUS is the damage-arresting nature of the stitches, which enables the use of fail-safe design principles. During the load testing of the MBB, ultrasonic nondestructive evaluation (NDE) was used to monitor several sites of intentional barely-visible impact damage (BVID) as well as to survey the areas surrounding the failure cracks after final loading to catastrophic failure. The damage-arresting ability of PRSEUS was confirmed by the results of NDE. In parallel with the large-scale structural testing of the MBB, mechanical tests were conducted of the PRSEUS rod-to-overwrap bonds, as measured by pushing the rod axially from a short length of stringer.

  20. Linear motion device and method for inserting and withdrawing control rods

    DOEpatents

    Smith, Jay E.

    1984-01-01

    A linear motion device, more specifically a control rod drive mechanism (CRDM) for inserting and withdrawing control rods into a reactor core, is capable of independently and sequentially positioning two sets of control rods with a single motor stator and rotor. The CRDM disclosed can control more than one control rod lead screw without incurring a substantial increase in the size of the mechanism.

  1. Inhibition to retinal rod bipolar cells is regulated by light levels

    PubMed Central

    Mazade, Reece E.; Klein, Justin S.

    2013-01-01

    The retina responds to a wide range of light stimuli by adaptation of retinal signaling to background light intensity and the use of two different photoreceptors: rods that sense dim light and cones that sense bright light. Rods signal to rod bipolar cells that receive significant inhibition from amacrine cells in the dark, especially from a rod bipolar cell-activated GABAergic amacrine cell. This inhibition modulates the output of rod bipolar cells onto downstream neurons. However, it was not clear how the inhibition of rod bipolar cells changes when rod signaling is limited by an adapting background light and cone signaling becomes dominant. We found that both light-evoked and spontaneous rod bipolar cell inhibition significantly decrease with light adaptation. This suggests a global decrease in the activity of amacrine cells that provide input to rod bipolar cells with light adaptation. However, inhibition to rod bipolar cells is also limited by GABAergic connections between amacrine cells, which decrease GABAergic input to rod bipolar cells. When we removed this serial inhibition, the light-evoked inhibition to rod bipolar cells remained after light adaptation. These results suggest that decreased inhibition to rod bipolar cells after light adaptation is due to decreased rod pathway activity as well as an active increase in inhibition between amacrine cells. Together these serve to limit rod bipolar cell inhibition after light adaptation, when the rod pathway is inactive and modulation of the signal is not required. This suggests an efficiency mechanism in the retina to limit unnecessary signaling. PMID:23596335

  2. Rod internal pressure quantification and distribution analysis using Frapcon

    SciTech Connect

    Bratton, Ryan N; Jessee, Matthew Anderson; Wieselquist, William A

    2015-09-01

    This report documents work performed supporting the Department of Energy (DOE) Office of Nuclear Energy (NE) Fuel Cycle Technologies Used Fuel Disposition Campaign (UFDC) under work breakdown structure element 1.02.08.10, ST Analysis. In particular, this report fulfills the M4 milestone M4FT- 15OR0810036, Quantify effects of power uncertainty on fuel assembly characteristics, within work package FT-15OR081003 ST Analysis-ORNL. This research was also supported by the Consortium for Advanced Simulation of Light Water Reactors (http://www.casl.gov), an Energy Innovation Hub (http://www.energy.gov/hubs) for Modeling and Simulation of Nuclear Reactors under U.S. Department of Energy Contract No. DE-AC05-00OR22725. The discharge rod internal pressure (RIP) and cladding hoop stress (CHS) distributions are quantified for Watts Bar Nuclear Unit 1 (WBN1) fuel rods by modeling core cycle design data, operation data (including modeling significant trips and downpowers), and as-built fuel enrichments and densities of each fuel rod in FRAPCON-3.5. A methodology is developed which tracks inter-cycle assembly movements and assembly batch fabrication information to build individual FRAPCON inputs for each evaluated WBN1 fuel rod. An alternate model for the amount of helium released from the zirconium diboride (ZrB2) integral fuel burnable absorber (IFBA) layer is derived and applied to FRAPCON output data to quantify the RIP and CHS for these types of fuel rods. SCALE/Polaris is used to quantify fuel rodspecific spectral quantities and the amount of gaseous fission products produced in the fuel for use in FRAPCON inputs. Fuel rods with ZrB2 IFBA layers (i.e., IFBA rods) are determined to have RIP predictions that are elevated when compared to fuel rod without IFBA layers (i.e., standard rods) despite the fact that IFBA rods often have reduced fill pressures and annular fuel pellets. The primary contributor to elevated RIP predictions at burnups less than and greater than 30 GWd

  3. Ricochet of a tungsten heavy alloy long-rod projectile from deformable steel plates

    NASA Astrophysics Data System (ADS)

    Lee, Woong; Lee, Heon-Joo; Shin, Hyunho

    2002-10-01

    Ricochet of a tungsten heavy alloy long-rod projectile from oblique steel plates with a finite thickness was investigated numerically using a full three-dimensional explicit finite element method. Three distinctive regimes resulting from oblique impact depending on the obliquity, namely simple ricochet, critical ricochet and target perforation, were investigated in detail. Critical ricochet angles were calculated for various impact velocities and strengths of the target plates. It was predicted that critical ricochet angle increases with decreasing impact velocities and that higher ricochet angles were expected if higher strength target materials are employed. Numerical predictions were compared with existing two-dimensional analytical models. Experiments were also carried out and the results supported the predictions of the numerical analysis.

  4. Numerical Study on Anti-Penetration Process of Alumina Ceramic (AD95) to Tungsten Long Rod Projectiles

    NASA Astrophysics Data System (ADS)

    Zhang, Xianfeng; Zhang, Niansong; Li, Yongchi

    Numerical studies were conducted on the ballistic performance of alumina ceramic (AD95) tiles based on depth of penetration method, when subjected to normal impact of tungsten long rod projectiles at velocities ranging from 1100 to 2000 ms-1. The residual depth on after-effect target was derived in each case, and the ballistic efficiency factor was determined using the corresponding penetration depth on medium carbon steel. Anti-penetration experiment study of the AD95 ceramic tiles to tungsten long rod projectiles has been carried out to verify the accuracy of numerical simulation model. The result shows that numerical simulation results agree well with the corresponding experiment results and AD95 ceramic has excellent ballistic performance than medium carbon steel. The ballistic efficiency factor increases with velocity increasing when impact velocity lower than 1300 ms-1, and when it was higher than 1300 ms-1 the ballistic efficiency factor has almost no difference.

  5. Responses of retinal rods to single photons.

    PubMed Central

    Baylor, D A; Lamb, T D; Yau, K W

    1979-01-01

    1. A suction electrode was used to record the membrane current of single rod outer segments in pieces of toad retina. During dim illumination the membrane current showed pronounced fluctuations. 2. Amplitude histograms of responses to dim flashes of fixed intensity exhibited two discrete peaks, one at 0 pA and one near 1 pA, suggesting that the response was quantized. By setting a criterion amplitude level, flash responses could be classed as 'failures' (no response) or as 'successes' (at least one quantal event). 3. The variation of fraction of successes with flash intensity was consistent with the hypothesis that each quantal electrical event resulted from a single photoisomerization. 4. The quantal event had a mean amplitude of about 1 pA (5% of the standing dark current) and a standard deviation of 0.2 pA. Dispersion in the event amplitude prevented identification of histogram peaks corresponding to two or more photoisomerizations. 5. Individual quantal responses exhibited a smooth shape very similar to that of the average quantal response. This suggests that a single photoisomerization releases many particles of transmitter and that radial diffusion of internal transmitter is not a major source of delay in the light response. 6. The 'quantum efficiency' with which an absorbed photon generated an electrical event was measured as 0.5 +/- 0.1 (S.E. of mean, n = 4). This is slightly lower than the quantum efficiency of photoisomerization obtained previously for rhodopsin in solution. 7. At wavelengths between 420 and 700 nm the quantal event was invariant in size, although the cell's sensitivity varied over a range of 10(5). 8. The power spectrum of the fluctuations in dim steady light was predicted by assuming that a random series of quantal events occurred independently. 9. In brighter light the fluctuations were faster, and the response to an incremental flash was reduced in size and duration. The power spectrum could be predicted by assuming random

  6. Rod/Coil Block Copolyimides for Ion-Conducting Membranes

    NASA Technical Reports Server (NTRS)

    Meador, Mary Ann B.; Kinder, James D.

    2003-01-01

    Rod/coil block copolyimides that exhibit high levels of ionic conduction can be made into diverse products, including dimensionally stable solid electrolyte membranes that function well over wide temperature ranges in fuel cells and in lithium-ion electrochemical cells. These rod/coil block copolyimides were invented to overcome the limitations of polymers now used to make such membranes. They could also be useful in other electrochemical and perhaps some optical applications, as described below. The membranes of amorphous polyethylene oxide (PEO) now used in lithium-ion cells have acceptably large ionic conductivities only at temperatures above 60 C, precluding use in what would otherwise be many potential applications at lower temperatures. PEO is difficult to process, and, except at the highest molecular weights it is not very dimensionally stable. It would be desirable to operate fuel cells at temperatures above 80 C to take advantage of better kinetics of redox reactions and to reduce contamination of catalysts. Unfortunately, proton-conduction performance of a typical perfluorosulfonic polymer membrane now used as a solid electrolyte in a fuel cell decreases with increasing temperature above 80 C because of loss of water from within the membrane. The loss of water has been attributed to the hydrophobic nature of the polymer backbone. In addition, perfluorosulfonic polymers are expensive and are not sufficiently stable for long-term use. Rod/coil block copolyimides are so named because each molecule of such a polymer comprises short polyimide rod segments alternating with flexible polyether coil segments (see figure). The rods and coils can be linear, branched, or mixtures of linear and branched. A unique feature of these polymers is that the rods and coils are highly incompatible, giving rise to a phase separation with a high degree of ordering that creates nanoscale channels in which ions can travel freely. The conduction of ions can occur in the coil phase

  7. Estimation of rod scale errors in geodetic leveling

    USGS Publications Warehouse

    Craymer, Michael R.; Vaníček, Petr; Castle, Robert O.

    1995-01-01

    Comparisons among repeated geodetic levelings have often been used for detecting and estimating residual rod scale errors in leveled heights. Individual rod-pair scale errors are estimated by a two-step procedure using a model based on either differences in heights, differences in section height differences, or differences in section tilts. It is shown that the estimated rod-pair scale errors derived from each model are identical only when the data are correctly weighted, and the mathematical correlations are accounted for in the model based on heights. Analyses based on simple regressions of changes in height versus height can easily lead to incorrect conclusions. We also show that the statistically estimated scale errors are not a simple function of height, height difference, or tilt. The models are valid only when terrain slope is constant over adjacent pairs of setups (i.e., smoothly varying terrain). In order to discriminate between rod scale errors and vertical displacements due to crustal motion, the individual rod-pairs should be used in more than one leveling, preferably in areas of contrasting tectonic activity. From an analysis of 37 separately calibrated rod-pairs used in 55 levelings in southern California, we found eight statistically significant coefficients that could be reasonably attributed to rod scale errors, only one of which was larger than the expected random error in the applied calibration-based scale correction. However, significant differences with other independent checks indicate that caution should be exercised before accepting these results as evidence of scale error. Further refinements of the technique are clearly needed if the results are to be routinely applied in practice.

  8. Store-operated channels regulate intracellular calcium in mammalian rods.

    PubMed

    Molnar, Tünde; Barabas, Peter; Birnbaumer, Lutz; Punzo, Claudio; Kefalov, Vladimir; Križaj, David

    2012-08-01

    Exposure to daylight closes cyclic nucleotide-gated (CNG) and voltage-operated Ca(2+) -permeable channels in mammalian rods. The consequent lowering of the cytosolic calcium concentration ([Ca(2+)](i)), if protracted, can contribute to light-induced damage and apoptosis in these cells. We here report that mouse rods are protected against prolonged lowering of [Ca(2+)](i) by store-operated Ca(2+) entry (SOCE). Ca(2+) stores were depleted in Ca(2+)-free saline supplemented with the endoplasmic reticulum (ER) sequestration blocker cyclopiazonic acid. Store depletion elicited [Ca(2+)](i) signals that exceeded baseline [Ca(2+)](i) by 5.9 ± 0.7-fold and were antagonized by an inhibitory cocktail containing 2-APB, SKF 96365 and Gd(3+). Cation influx through SOCE channels was sufficient to elicit a secondary activation of L-type voltage-operated Ca2+ entry. We also found that TRPC1, the type 1 canonical mammalian homologue of the Drosophila photoreceptor TRP channel, is predominantly expressed within the outer nuclear layer of the retina. Rod loss in Pde6b(rdl) (rd1), Chx10/Kip1(-/-rdl) and Elovl4(TG2) dystrophic models was associated with ∼70% reduction in Trpc1 mRNA content whereas Trpc1 mRNA levels in rodless cone-full Nrl(-/-) retinas were decreased by ∼50%. Genetic ablation of TRPC1 channels, however, had no effect on SOCE, the sensitivity of the rod phototransduction cascade or synaptic transmission at rod and cone synapses. Thus, we localized two new mechanisms, SOCE and TRPC1, to mammalian rods and characterized the contribution of SOCE to Ca(2+) homeostasis. By preventing the cytosolic [Ca(2+)](i) from dropping too low under sustained saturating light conditions, these signalling pathways may protect Ca(2+)-dependent mechanisms within the ER and the cytosol without affecting normal rod function. PMID:22674725

  9. Strategy for Fuel Rod Receipt, Characterization, Sample Allocation for the Demonstration Sister Rods

    SciTech Connect

    Marschman, Steven C.; Warmann, Stephan A.; Rusch, Chris

    2014-03-01

    , inert gas backfilling, and transfer to an Independent Spent Fuel Storage Installation (ISFSI) for multi-year storage. To document the initial condition of the used fuel prior to emplacement in a storage system, “sister ” fuel rods will be harvested and sent to a national laboratory for characterization and archival purposes. This report supports the demonstration by describing how sister rods will be shipped and received at a national laboratory, and recommending basic nondestructive and destructive analyses to assure the fuel rods are adequately characterized for UFDC work. For this report, a hub-and-spoke model is proposed, with one location serving as the hub for fuel rod receipt and characterization. In this model, fuel and/or clad would be sent to other locations when capabilities at the hub were inadequate or nonexistent. This model has been proposed to reduce DOE-NE’s obligation for waste cleanup and decontamination of equipment.

  10. Extensional behavior of rod suspension in dilute polymer solution

    NASA Astrophysics Data System (ADS)

    Han, Hyejin; Kim, Chongyoup

    2015-08-01

    Extensional viscosity of rod particle suspensions in polymer solutions is studied experimentally. Rod particle suspensions were prepared by dispersing FeOOH rods in polyacrylamide (molecular weight of 5-6 M) solutions in a glycerin-water mixture. The diameter of rod particles was 100 nm and the aspect ratio was 4.3, 8.7 and 15.6. Particle volume fraction was 0.005-0.02. The extensional viscosity was measured by the capillary thinning method using the commercially available CaBER. Under the experimental condition both the polymer solution and particle suspensions are dilute. Particle-particle interaction is neglected in the solutions which are stretched by the extensional flow at the bulk. The result shows that extensional viscosity of the rod suspension in polymer solution decreases with the increase in particle volume fraction. The decrease is ascribed to the change in polymer conformation from the stretched state in the bulk flow to the less stretched state in shear flow developed near the particle to match the no-slip condition at the particle surface.

  11. Circadian and light-driven regulation of rod dark adaptation

    PubMed Central

    Xue, Yunlu; Shen, Susan Q.; Corbo, Joseph C.; Kefalov, Vladimir J.

    2015-01-01

    Continuous visual perception and the dark adaptation of vertebrate photoreceptors after bright light exposure require recycling of their visual chromophore through a series of reactions in the retinal pigmented epithelium (RPE visual cycle). Light-driven chromophore consumption by photoreceptors is greater in daytime vs. nighttime, suggesting that correspondingly higher activity of the visual cycle may be required. However, as rod photoreceptors are saturated in bright light, the continuous turnover of their chromophore by the visual cycle throughout the day would not contribute to vision. Whether the recycling of chromophore that drives rod dark adaptation is regulated by the circadian clock and light exposure is unknown. Here, we demonstrate that mouse rod dark adaptation is slower during the day or after light pre-exposure. This surprising daytime suppression of the RPE visual cycle was accompanied by light-driven reduction in expression of Rpe65, a key enzyme of the RPE visual cycle. Notably, only rods in melatonin-proficient mice were affected by this daily visual cycle modulation. Our results demonstrate that the circadian clock and light exposure regulate the recycling of chromophore in the RPE visual cycle. This daily melatonin-driven modulation of rod dark adaptation could potentially protect the retina from light-induced damage during the day. PMID:26626567

  12. Silica-based rod lens for the medical fiberscope

    NASA Astrophysics Data System (ADS)

    Nakatate, Ken-ichi; Shamoto, Naoki; Oohashi, Tateuki; Tsumanuma, Takashi; Sanada, Kazuo

    1994-07-01

    The ultrathin fiberscope, in which the outer diameter is under 1.0 mm, has made possible the direct observation of narrow portions within the human body. The fiberscope mainly consists of the imagefiber, the objective lens, and the illumination fiber, and each advance of these devices has brought the reduction of the scope-diameter. We have investigated the silica based rod lens for the following merits: (1) The fiberscope can be sterilized by the (gamma) -ray instead of ethylene oxide gas which has the problem of carcinogenicity, because the silica glass has high radiation resistant characteristics. (2) The silica based rod lens can be spliced with the imagefiber without any adhesive agent by using the arc fusion splicing machine. As a result, the reliability of the fiberscope can be significantly improved. The silica based rod lens with 125 micrometers in diameter was fabricated by drawing from preform rod made by the vapor phase axial deposition method. The characteristics of their images were evaluated by the modulation transfer function method. This paper presents the details of the fabrication technique of the silica based rod lens and its characteristics.

  13. Dysprosium titanate as an absorber material for control rods

    NASA Astrophysics Data System (ADS)

    Risovany, V. D.; Varlashova, E. E.; Suslov, D. N.

    2000-09-01

    Disprosium titanate is an attractive control rod material for the thermal neutron reactors. Its main advantages are: insignificant swelling, no out-gassing under neutron irradiation, rather high neutron efficiency, a high melting point (˜1870°C), non-interaction with the cladding at temperatures above 1000°C, simple fabrication and easily reprocessed non-radioactive waste. It can be used in control rods as pellets and powder. The disprosium titanate control rods have worked off in the MIR reactor for 17 years, in VVER-1000 - for 4 years without any operating problems. After post-irradiation examinations this type of control rod having high lifetime was recommended for the VVER and RBMK. The paper presents the examination results of absorber element dummies containing dysprosium titanate, irradiated in the SM reactor to the neutron fluence of 3.4×10 22 cm -2 ( E>0.1 MeV) and, also, the data on structure, thermal-physical properties of dysprosium titanate, efficiency of dysprosium titanate control rods.

  14. Fault pseudotachylyte: a coseismic lightning rod

    NASA Astrophysics Data System (ADS)

    Ferre, E. C.; Conder, J. A.; MathanaSekaran, N.; Geissman, J. W.

    2013-12-01

    of melt during the formation of a pseudotachylite vein. The increase in melt temperature is the most important factor affecting electrical conductivity in the fault plane. When the melt temperature rises from 1300 to 2000K, its electrical conductivity increases about 80 times. This implies that once a continuous pseudotachylite sheet-like vein is formed during an earthquake, the vein has a much higher electrical conductivity than its host-rock. The dramatic increase in electrical conductivity along the pseudotachylite plane might be synchronous with the generation of the coseismic electrical current. Thus, regardless of its origin, any electrical current produced during an earthquake will travel along the pseudotachylite plane which acts as a lightning rod. The magnetization of a solid due to an electrical current results from Biot-Savart law which states that an electrical current generates a magnetic field. The solidification of the pseudotachylite vein does not happen at once but proceeds from the margin inwards as an electrical current may still pass through the conducting pseudotachylite. Therefore, the host-rock of the pseudotachylite vein or its solidified margin can be magnetized by a coseismic current.

  15. Gap-junctional coupling of mammalian rod photoreceptors and its effect on visual detection

    PubMed Central

    Li, Peter H.; Verweij, Jan; Long, James H.; Schnapf, Julie L.

    2012-01-01

    The presence of gap junctions between rods in mammalian retina suggests a role for rod-rod coupling in human vision. Rod coupling is known to reduce response variability, but because junctional conductances are not known, the downstream effects on visual performance are uncertain. Here we assessed rod coupling in guinea pig retina by measuring: 1) the variability in responses to dim flashes, 2) Neurobiotin tracer coupling, and 3) junctional conductances. Results were consolidated into an electrical network model and a model of human psychophysical detection. Guinea pig rods form tracer pools of 1 to ~20 rods, with junctional conductances averaging ~350 pS. We calculate that coupling will reduce human dark-adapted sensitivity ~10% by impairing the noise filtering of the synapse between rods and rod bipolar cells. However, coupling also mitigates synaptic saturation and is thus calculated to improve sensitivity when stimuli are spatially restricted or are superimposed over background illumination. PMID:22399777

  16. Prominent 946 lines induced from flashlamp pumped Nd: YAG rod

    NASA Astrophysics Data System (ADS)

    Bidin, Noriah; Zainal, Roslinda; Daud, Yaacob Mat; Pourmand, Seyed Ebrahim; Bakhtiar, Hazri

    2012-06-01

    Spectroscopic properties of Nd:YAG laser rod pumped by a new developed flashlamp is investigated. A new power supply is constructed to power xenon flashlamp. A 1 at.% Nd:YAG laser rod is transversely pumped by the flashlamp and stabilized by a water cooling system operated at ambient temperature of 20°C. The absorption and emission spectrum of the flashlamp pumped Nd:YAG rod is analyzed via spectroscopy technique. The peak absorption line is identified to be at 882 nm. The dominant emission line obtained from transition 4F3/2→4I9/2 comprised of quasi three level laser at 938.5 and 946 nm with the corresponding cross section of 2.42×10-19cm2 and 3.04×10-19cm2 respectively. This cross section is found almost ten times greater than the usual one.

  17. Columnar versus smectic order in systems of charged colloidal rods

    NASA Astrophysics Data System (ADS)

    Wensink, H. H.

    2007-05-01

    We study the stability of inhomogeneous liquid crystalline states in systems of monodisperse, stiff, charged rods. By means of a bifurcation analysis applied to the Onsager free energy for charged rods in strongly nematic states, we investigate nematic-smectic and nematic-columnar instabilities as a function of the Debye screening length κ-1. While the nematic-smectic transition clearly preempts the nematic-columnar one in the regime of strong screening (i.e., small κ-1) a marked stability of hexagonal columnar order is observed at larger screening lengths. The theoretical results are substantiated by Brownian dynamics computer simulation results based on the Yukawa site model. Our connect to experiments on tobacco mosaic virus rods, in particular, but might be relevant for soft rodlike mesogens in strong external directional fields in general.

  18. Simulations of optical sensors fabricated from metallic rods couplers

    SciTech Connect

    Singh, M. R.; Balakrishanan, Shankar

    2014-03-31

    We have developed the optical sensing mechanism of photonic couplers fabricated from the periodically arranged metallic rods. The metallic rod lattice is embedded between two dielectric material waveguides. This structure is called metallic coupler. Using the transfer matrix method, expressions for the reflection and transmission coefficients of electromagnetic wave propagating in waveguides have been obtained. We found that for certain energies, the electromagnetic wave is totally reflected from the coupler. Similarly, for a certain energy range the light is totally transmitted. It has also been found that by changing the periodicity of the metallic rods, the transmitted energy can be reflected. The periodicity of the metallic lattice can be modified by applying an external stress or pressure. In other words, the system can be used as stress and pressure sensors. The present findings can be used to make new types photonic sensors.

  19. Overview of rod-bundle thermal-hydraulic analysis

    SciTech Connect

    Sha, W.T.

    1980-11-01

    Three methods used in rod-bundle thermal-hydraulic analysis are summarized. These methods are: (1) subchannel analysis, and its inherent assumptions are clearly stated; (2) porous medium formulation with volume porosity, surface permeability, distributed resistance and distributed heat source (sink) - the concept of surface permeability is new in porous medium formulation, and greatly facilitates modeling anisotropic effects; and (3) benchmark rod-bundle thermal-hydraulic analysis using a boundary-fitted coordinate system, and it represents the most rigorous method to date. For laminar flow, this method gives solutions without any assumptions and it requires information on rod bundle geometry and thermal physical properties of the fluid. Basic limitations and merits of each method are discussed in detail. 19 refs., 6 figs., 1 tab.

  20. The role of attractive interactions in rod-sphere mixtures.

    PubMed

    Antypov, Dmytro; Cleaver, Douglas J

    2004-06-01

    We present a computer simulation study of binary mixtures of prolate Gay-Berne particles and Lennard-Jones spheres. Results are presented for three such rod-sphere systems which differ from each other only in the interaction between unlike particles. Both the mixing-demixing behavior and the transitions between the isotropic and any liquid crystalline phases are studied for each system, as a function of temperature and concentration ratio. For systems which show macroscopic demixing, the rod-sphere interaction is shown to give direct control over interfacial anchoring properties, giving rise to the possibility of micellar phase formation in the case of homeotropic anchoring. Additionally, it is shown that on incorporating high concentrations of spheres into a system of rods with weak demixing properties, microphase-separated structures can be induced, including bicontinuous and lamellar arrangements. PMID:15268056

  1. Dynamic features of rod-shaped Au nanoclusters

    NASA Astrophysics Data System (ADS)

    So, Woong Young; Das, Anindita; Wang, Shuxin; Zhao, Shuo; Byun, Hee Young; Lee, Dana; Kumar, Santosh; Jin, Rongchao; Peteanu, Linda A.

    2015-08-01

    Gold nanoclusters hold many potential applications such as biosensing and optics due to their emission characteristics, small size, and non-toxicity. However, their low quantum yields remain problematic for further applications, and their fluorescence mechanism is still unclear. To increase the low quantum yields, various methods have been performed: doping, tuning structures, and changing number of gold atoms. In the past, most characterizations have been performed on spherical shaped nanoclusters; in this paper, several characterizations of various rod-shaped Au nanoclusters specifically on Au25 are shown. It has been determined that the central gold atom in Au25 nano-rod is crucial in fluorescence. Furthermore, single molecule analysis of silver doped Au25 nano-rod revealed that it has more photo-stability than conjugated polymers and quantum dots.

  2. Noise Radiation from Single and Multiple Rod Configurations

    NASA Technical Reports Server (NTRS)

    Hutcheson, Florence V.; Brooks, Thomas F.

    2006-01-01

    Acoustic measurements were performed on single and multiple rod configurations to study the effect of Reynolds number, surface roughness, freestream turbulence, proximity and wake interference on the radiated noise. The Reynolds number ranged from 3.8 x 10(exp 3) to 10(exp 5). Directivity measurements were performed to determine how well the dipole assumption for the radiation of vortex shedding noise holds for the different model configurations tested. The dependence of the peak Sound Pressure Level on velocity was also examined. Several concepts for the reduction of the noise radiating from cylindrical rods were tested. It was shown that wire wraps and collar distributions could be used to significantly reduce the noise radiating from rods in tandem configurations.

  3. Model of coarsening and vortex formation in vibrated granular rods.

    SciTech Connect

    Aranson, I. S.; Tsimring, L. S.; Materials Science Division; Univ. of California at San Diego

    2003-02-01

    Neicu et al. observed experimentally spontaneous formation of the long-range orientational order and large-scale vortices in a system of vibrated macroscopic rods. We propose a phenomenological theory of this phenomenon based on a coupled system of equations for local rods density and tilt. The density evolution is described by the modified Cahn-Hilliard equation, while the tilt is described by the Ginzburg-Landau type equation. Our analysis shows that, in accordance with the Cahn-Hilliard dynamics, islands of the ordered phase appear spontaneously and grow due to coarsening. The generic vortex solutions of the Ginzburg-Landau equation for the tilt correspond to the vortical motion of the rods around the cores which are located near the centers of the islands.

  4. Tumbling of a rigid rod in a shear flow

    NASA Astrophysics Data System (ADS)

    van Leeuwen, J. M. J.; Blöte, H. W. J.

    2014-09-01

    The tumbling of a rigid rod in a shear flow is analyzed in the high viscosity limit. Following Burgers, the Master Equation is derived for the probability distribution of the orientation of the rod. The equation contains one dimensionless number, the Weissenberg number, which is the ratio of the shear rate and the orientational diffusion constant. The equation is solved for the stationary state distribution for arbitrary Weissenberg numbers, in particular for the limit of high Weissenberg numbers. The stationary state gives an interesting flow pattern for the orientation of the rod, showing the interplay between flow due to the driving shear force and diffusion due to the random thermal forces of the fluid. The average tumbling time and tumbling frequency is calculated as a function of the Weissenberg number. A simple crossover function is proposed which covers the whole regime from small to large Weissenberg numbers.

  5. Three-Phase Coexistence in Colloidal Rod-Plate Mixtures.

    PubMed

    Woolston, Phillip; van Duijneveldt, Jeroen S

    2015-09-01

    Aqueous suspensions of clay particles, such as montmorillonite (MMT) platelets and sepiolite (Sep) rods, tend to form gels at concentrations around 1 vol %. For Sep rods, adsorbing sodium polyacrylate to the surface allows for an isotropic-nematic phase separation to be seen instead. Here, MMT is added to such Sep suspensions, resulting in a complex phase behavior. Across a range of clay concentrations, separation into three phases is observed: a lower, nematic phase dominated by Sep rods, a MMT-rich middle layer, which is weakly birefringent and probably a gel, and a dilute top phase. Analysis of phase volumes suggests that the middle layer may contain as much as 6 vol % MMT. PMID:26262770

  6. Adaptive potentiation in rod photoreceptors after light exposure.

    PubMed

    McKeown, Alex S; Kraft, Timothy W

    2014-06-01

    Photoreceptors adapt to changes in illumination by altering transduction kinetics and sensitivity, thereby extending their working range. We describe a previously unknown form of rod photoreceptor adaptation in wild-type (WT) mice that manifests as a potentiation of the light response after periods of conditioning light exposure. We characterize the stimulus conditions that evoke this graded hypersensitivity and examine the molecular mechanisms of adaptation underlying the phenomenon. After exposure to periods of saturating illumination, rods show a 10-35% increase in circulating dark current, an adaptive potentiation (AP) to light exposure. This potentiation grows as exposure to light is extended up to 3 min and decreases with longer exposures. Cells return to their initial dark-adapted sensitivity with a time constant of recovery of ∼7 s. Halving the extracellular Mg concentration prolongs the adaptation, increasing the time constant of recovery to 13.3 s, but does not affect the magnitude of potentiation. In rods lacking guanylate cyclase activating proteins 1 and 2 (GCAP(-/-)), AP is more than doubled compared with WT rods, and halving the extracellular Mg concentration does not affect the recovery time constant. Rods from a mouse expressing cyclic nucleotide-gated channels incapable of binding calmodulin also showed a marked increase in the amplitude of AP. Application of an insulin-like growth factor-1 receptor (IGF-1R) kinase inhibitor (Tyrphostin AG1024) blocked AP, whereas application of an insulin receptor kinase inhibitor (HNMPA(AM)3) failed to do so. A broad-acting tyrosine phosphatase inhibitor (orthovanadate) also blocked AP. Our findings identify a unique form of adaptation in photoreceptors, so that they show transient hypersensitivity to light, and are consistent with a model in which light history, acting via the IGF-1R, can increase the sensitivity of rod photoreceptors, whereas the photocurrent overshoot is regulated by Ca-calmodulin and Ca(2

  7. Adaptive potentiation in rod photoreceptors after light exposure

    PubMed Central

    McKeown, Alex S.

    2014-01-01

    Photoreceptors adapt to changes in illumination by altering transduction kinetics and sensitivity, thereby extending their working range. We describe a previously unknown form of rod photoreceptor adaptation in wild-type (WT) mice that manifests as a potentiation of the light response after periods of conditioning light exposure. We characterize the stimulus conditions that evoke this graded hypersensitivity and examine the molecular mechanisms of adaptation underlying the phenomenon. After exposure to periods of saturating illumination, rods show a 10–35% increase in circulating dark current, an adaptive potentiation (AP) to light exposure. This potentiation grows as exposure to light is extended up to 3 min and decreases with longer exposures. Cells return to their initial dark-adapted sensitivity with a time constant of recovery of ∼7 s. Halving the extracellular Mg concentration prolongs the adaptation, increasing the time constant of recovery to 13.3 s, but does not affect the magnitude of potentiation. In rods lacking guanylate cyclase activating proteins 1 and 2 (GCAP−/−), AP is more than doubled compared with WT rods, and halving the extracellular Mg concentration does not affect the recovery time constant. Rods from a mouse expressing cyclic nucleotide–gated channels incapable of binding calmodulin also showed a marked increase in the amplitude of AP. Application of an insulin-like growth factor-1 receptor (IGF-1R) kinase inhibitor (Tyrphostin AG1024) blocked AP, whereas application of an insulin receptor kinase inhibitor (HNMPA(AM)3) failed to do so. A broad-acting tyrosine phosphatase inhibitor (orthovanadate) also blocked AP. Our findings identify a unique form of adaptation in photoreceptors, so that they show transient hypersensitivity to light, and are consistent with a model in which light history, acting via the IGF-1R, can increase the sensitivity of rod photoreceptors, whereas the photocurrent overshoot is regulated by Ca-calmodulin and

  8. Calcium diffusion coefficient in rod photoreceptor outer segments.

    PubMed Central

    Nakatani, Kei; Chen, Chunhe; Koutalos, Yiannis

    2002-01-01

    Calcium (Ca(2+)) modulates several of the enzymatic pathways that mediate phototransduction in the outer segments of vertebrate rod photoreceptors. Ca(2+) enters the rod outer segment through cationic channels kept open by cyclic GMP (cGMP) and is pumped out by a Na(+)/Ca(2+),K(+) exchanger. Light initiates a biochemical cascade, which leads to closure of the cGMP-gated channels, and a concomitant decline in the concentration of Ca(2+). This decline mediates the recovery from stimulation by light and underlies the adaptation of the cell to background light. The speed with which the decline in the Ca(2+) concentration propagates through the rod outer segment depends on the Ca(2+) diffusion coefficient. We have used the fluorescent Ca(2+) indicator fluo-3 and confocal microscopy to measure the profile of the Ca(2+) concentration after stimulation of the rod photoreceptor by light. From these measurements, we have obtained a value of 15 +/- 1 microm(2)s(-1) for the radial Ca(2+) diffusion coefficient. This value is consistent with the effect of a low-affinity, immobile buffer reported to be present in the rod outer segment (L.Lagnado, L. Cervetto, and P.A. McNaughton, 1992, J. Physiol. 455:111-142) and with a buffering capacity of approximately 20 for rods in darkness(S. Nikonov, N. Engheta, and E.N. Pugh, Jr., 1998, J. Gen. Physiol. 111:7-37). This value suggests that diffusion provides a significant delay for the radial propagation of the decline in the concentration of Ca(2+). Also, because of baffling by the disks, the longitudinal Ca(2+) diffusion coefficient will be in the order of 2 microm(2)s(-1), which is much smaller than the longitudinal cGMP diffusion coefficient (30-60 microm(2)s(-1); ). Therefore, the longitudinal decline of Ca(2+) lags behind the longitudinal spread of excitation by cGMP. PMID:11806915

  9. Lightweight piston-rod assembly for a reciprocating machine

    DOEpatents

    Corey, John A.; Walsh, Michael M.

    1986-01-01

    In a reciprocating machine, there is provided a hollow piston including a dome portion on one end and a base portion on the opposite end. The base portion includes a central bore into which a rod is hermetically fixed in radial and angular alignment. The extending end of the rod has a reduced diameter portion adapted to fit into the central bore of a second member such as a cross-head assembly, and to be secured thereto in radial and axial alignment with the piston.

  10. NEUTRONIC REACTOR CONTROL ROD AND METHOD OF FABRICATION

    DOEpatents

    Porembka, S.W. Jr.

    1961-06-27

    A reactor control rod formed from a compacted powder dispersion is patented. The rod consists of titanium sheathed with a cladding alloy. The cladding alloy contains 1.3% to 1.6% by weight of tin, 0.07% to 0.12% by weight of chromium, 0.04% to 0.08% by weight of nickel, 0.09% to 0.16% by weight of iron, carbon not exceeding 0.05%, less than 0.5% by weight of incidental impurities, and the balance zirconium.

  11. Compressional and torsional wave amplitudes in rods with periodic structures

    NASA Astrophysics Data System (ADS)

    Morales, A.; Flores, J.; Gutierrez, L.; Mendez-Sanchez, R. A.

    2002-11-01

    To measure and detect elastic waves in metallic rods a low-frequency electromagnetic-acoustic transducer has been developed. Frequencies range from a few hertz up to hundreds of kilohertz. With appropriate configuration of the transducer, compressional or torsional waves can be selectively excited or detected. Although the transducer can be used in many different situations, it has been tested and applied to a locally periodic rod, which consists of a finite number of unit cells. The measured wave amplitudes are compared with theoretical ones, obtained with the one-dimensional transfer matrix method, and excellent agreement is obtained. copyright 2002 Acoustical Society of America.

  12. Gene expression changes during retinal development and rod specification

    PubMed Central

    Carrigan, Matthew; Hokamp, Karsten; Farrar, G. Jane

    2015-01-01

    Purpose Retinitis pigmentosa (RP) typically results from individual mutations in any one of >70 genes that cause rod photoreceptor cells to degenerate prematurely, eventually resulting in blindness. Gene therapies targeting individual RP genes have shown efficacy at clinical trial; however, these therapies require the surviving photoreceptor cells to be viable and functional, and may be economically feasible for only the more commonly mutated genes. An alternative potential treatment strategy, particularly for late stage disease, may involve stem cell transplants into the photoreceptor layer of the retina. Rod progenitors from postnatal mouse retinas can be transplanted and can form photoreceptors in recipient adult retinas; optimal numbers of transplantable cells are obtained from postnatal day 3–5 (P3–5) retinas. These cells can also be expanded in culture; however, this results in the loss of photoreceptor potential. Gene expression differences between postnatal retinas, cultured retinal progenitor cells (RPCs), and rod photoreceptor precursors were investigated to identify gene expression patterns involved in the specification of rod photoreceptors. Methods Microarrays were used to investigate differences in gene expression between cultured RPCs that have lost photoreceptor potential, P1 retinas, and fresh P5 retinas that contain significant numbers of transplantable photoreceptors. Additionally, fluorescence-activated cell sorting (FACS) sorted Rho-eGFP-expressing rod photoreceptor precursors were compared with Rho-eGFP-negative cells from the same P5 retinas. Differential expression was confirmed with quantitative polymerase chain reaction (q-PCR). Results Analysis of the microarray data sets, including the use of t-distributed stochastic neighbor embedding (t-SNE) to identify expression pattern neighbors of key photoreceptor specific genes, resulted in the identification of 636 genes differentially regulated during rod specification. Forty-four of these

  13. Rotation of a rod system containing inertial fluid flow

    NASA Astrophysics Data System (ADS)

    Sergeev, A. D.

    2012-11-01

    This paper considers a rod system for which it is possible to correctly formulate and solve the problem of three-dimensional motion in the physical space of an elastic pipeline area containing inertial incompressible fluid flow. The precession of the axis of an elastic pipeline along which inertial incompressible fluid flows is described, a physical phenomenon which has not been previously studied. With the use of rigid body dynamics, it was theoretically established that a three-dimensional dynamic process is possible in an open (exchanging mass with the environment) elastic-inertial rod system.

  14. Computer simulations to study the effect of adiabatic heating on rod penetration

    SciTech Connect

    Reaugh, J.E.

    1993-08-01

    We use computer simulations to help us understand the experimental observation that depleted uranium (DU) rods penetrate more steel than equal density tungsten alloy (WA) rods, and that this advantage depends on velocity and fineness ratio. Our simulations used thermal softening. Although the DU rods exhibit shear fracture instead, both phenomena result in a loss of hoop strength, and help to keep the projectile residue from interfering with the incoming rod. Our simulations show that rods of DU (or other alloy with strong thermal softening) penetrate more steel than rods of WA (for alloys with little thermal softening), and show velocity and fineness ratio dependencies that are in qualitative agreement with experiment.

  15. Method and apparatus for monitoring the control rods of a nuclear reactor

    SciTech Connect

    Gravelle, A.; Marini, J.; Romy, D.

    1984-12-04

    Method and apparatus for monitoring the movement of the control rods of a nuclear reactor. The number of steps of movement in either direction of the rod from which the control rod is suspended is counted. According to the height of the step, an indication of the position of the suspension rod and of the control rod. The apparatus comprises devices for measuring the speed of movement of the control rod, for logging variations in speed higher than a given value, and for counting such variations according to their sign. The invention is particularly useful in pressurized water nuclear reactors.

  16. 76 FR 61135 - Environmental Impact Statement: Theodore Francis Green Airport, Warwick, RI

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-10-03

    ... Federal Aviation Administration Environmental Impact Statement: Theodore Francis Green Airport, Warwick... Environmental Impact Statement (EIS) has been prepared for Theodore Francis Green Airport, in Warwick, Rhode... Theodore Francis Green Airport, in Warwick, Rhode Island. The ROD documents the final Agency...

  17. Axial power monitor rod issues and resolution for K-14.1

    SciTech Connect

    Easterling, T.C.; Fields, C.C.; Hightower, N.T. III; Wooten, L.A.; Andre, S.K.; Apperson, C.E.; Bailey, M.H.; Bell, D.L.; Clare, G.H.; Collins, S.L.; Croft, W.D.; Edwards, T.B.; Geiger, G.T.; Harris, S.P.; Lietzow, J.L.; McCulloch, R.W.; McFarlane, A.F.; Randolph, H.W.; Reed, R.L.; Reeve, C.P.; Revolinski, S.M.; Sessions, H.T.; Shine, E.P.; Smith, T.A.; Sossman, C.L.; Taylor, J.J.; Weber, J.H.

    1992-05-01

    A recent concern arose over the treatment of uncertainty associated with the K-Reactor axial power monitors (APMs). There are nine axial power monitor rods located at various positions in the K-Reactor core. By comparing the output of one sensor near the top of the rod to the output of another sensor near the bottom of the rod, the relative ratio of the neutron flux from the top to the bottom of the core can be determined. This ratio is called the roof-top-ratio (RTR) and is the output of a top sensor (Sensor 2) divided by the output of a bottom sensor (Sensor 6). The RTR is important to the safety analyses because when the RTR is maintained within certain ranges, the severity of reactivity transients is limited. There are uncertainties associated with the equipment`s ability to measure the true roof top ratio. It was determined recently that sufficient uncertainty was not accounted for either in reactor operation or in the safety analyses. The concern about uncertainty was addressed for three separate issues. One issue dear with the linear response of the sensors for power ranges planned for K-Reactor operation. The second issue dear with overall uncertainty in the RTR channel. The third issue dear with apparent large ranges in confidence bands for the RTR at low reactor powers as represented by original vendor data. Plots of sparse vendor data indicated unacceptably large uncertainties in RTR would have to be accounted for at the power ranges planned for K-Reactor operation. These concerns were brought to management`s attention through the existing procedures for notification, irrespective of their potential impact on the restart schedule. Analyses have been completed to resolve the APM issues described above, and work is progressing to take the needed steps to change operational procedures.

  18. Preliminary design report for modeling of hydrogen uptake in fuel rod cladding during severe accidents

    SciTech Connect

    Siefken, L.J.

    1998-08-01

    Preliminary designs are described for models of the interaction of Zircaloy and hydrogen and the consequences of this interaction on the behavior of fuel rod cladding during severe accidents. The modeling of this interaction and its consequences involves the modeling of seven processes: (1) diffusion of oxygen from the bulk gas into the boundary layer at the external cladding surface, (2) diffusion from the boundary layer into the oxide layer at the cladding external surface, (3) diffusion from the inner surface of the oxide layer into the metallic part of the cladding, (4) uptake of hydrogen in the event that the cladding oxide layer is dissolved in a steam-starved region, (5) embrittlement of cladding due to hydrogen uptake, (6) cracking of cladding during quenching due to its embrittlement and (7) release of hydrogen from the cladding after cracking of the cladding. An integral diffusion method is described for calculating the diffusion processes in the cladding. Experimental and theoretical results are presented that show the uptake of hydrogen in the event of dissolution of the oxide layer occurs rapidly and that show the release of hydrogen in the event of cracking of the cladding occurs rapidly. These experimental results are used as a basis for calculating the rate of hydrogen uptake and the rate of hydrogen release. The uptake of hydrogen is limited to the equilibrium solubility calculated by applying Sievert`s law. The uptake of hydrogen is an exothermic reaction that accelerates the heatup of a fuel rod. An embrittlement criteria is described that accounts for hydrogen and oxygen concentration and the extent of oxidation. A design is described for implementing the models for Zr-H interaction into the programming framework of the SCDAP/RELAP5 code. A test matrix is described for assessing the impact of the Zr-H interaction models on the calculated behavior of fuel rods in severe accident conditions.

  19. Mechanisms, pools, and sites of spontaneous vesicle release at synapses of rod and cone photoreceptors.

    PubMed

    Cork, Karlene M; Van Hook, Matthew J; Thoreson, Wallace B

    2016-08-01

    Photoreceptors have depolarized resting potentials that stimulate calcium-dependent release continuously from a large vesicle pool but neurons can also release vesicles without stimulation. We characterized the Ca(2+) dependence, vesicle pools, and release sites involved in spontaneous release at photoreceptor ribbon synapses. In whole-cell recordings from light-adapted horizontal cells (HCs) of tiger salamander retina, we detected miniature excitatory post-synaptic currents (mEPSCs) when no stimulation was applied to promote exocytosis. Blocking Ca(2+) influx by lowering extracellular Ca(2+) , by application of Cd(2+) and other agents reduced the frequency of mEPSCs but did not eliminate them, indicating that mEPSCs can occur independently of Ca(2+) . We also measured release presynaptically from rods and cones by examining quantal glutamate transporter anion currents. Presynaptic quantal event frequency was reduced by Cd(2+) or by increased intracellular Ca(2+) buffering in rods, but not in cones, that were voltage clamped at -70 mV. By inhibiting the vesicle cycle with bafilomycin, we found the frequency of mEPSCs declined more rapidly than the amplitude of evoked excitatory post-synaptic currents (EPSCs) suggesting a possible separation between vesicle pools in evoked and spontaneous exocytosis. We mapped sites of Ca(2+) -independent release using total internal reflectance fluorescence (TIRF) microscopy to visualize fusion of individual vesicles loaded with dextran-conjugated pHrodo. Spontaneous release in rods occurred more frequently at non-ribbon sites than evoked release events. The function of Ca(2+) -independent spontaneous release at continuously active photoreceptor synapses remains unclear, but the low frequency of spontaneous quanta limits their impact on noise. PMID:27255664

  20. Rigorous statistical mechanical results for one-dimensional bounded soft rod systems and for soft rod mixtures

    NASA Astrophysics Data System (ADS)

    Swadesh, Joel K.; Poirier, Jacques C.

    1981-05-01

    We obtain the exact partition functions for modified soft rod systems, thus exploring mixing and end effects. A hypergeometric function appears in each partition function. For a soft and hard rod mixture, we exhibit the excess Helmholtz free energy of mixing in the thermodynamic limit. Using the centrally important integral I( D, M', L, b1), closely related to the confluent hypergeometric function 1F1, we have sketched the evaluation of the soft rod partition function in a form containing 1F1 rather than a Bessel function as derived earlier by us [6]. Again using I( D, M', L, b1) but with altered indices, we have evaluated the partition function for soft rods with hard and soft boundaries in terms of the 1F1 function. We have recognized that the sum of these two partition functions, multiplied by N' equals the partition function of a system of soft rods subject to periodic boundary conditions. Conceptually, then, periodic boundary conditions in the soft rod system are equivalent to imposition of either hard or soft boundary conditions. Additionally, we have noted that soft boundary conditions are equivalent to a two-phase system composed of a bound monolayer and a free bulk phase. Again using I( D, M', L, b1), we have obtained the exact partition function of a mixture of hard and soft rods by a modification of the integral indices. In order to derive results of potential utility in solution theory, we have obtained the thermodynamic limit of this partition function, and have derived the excess Helmholtz free energy of mixing at constant number density and temperature. At high and low temperatures, this excess function assumes greatly simplified mathematical forms. Finally, we have obtained the exact partition function for a finite binary mixture of soft rods of different force constants, using I( D, M', L, b1) to generate an intermediate result which led to a partition function containing a hypergeometric function. We hope that the results of this work, which

  1. Intraoperative implant rod three-dimensional geometry measured by dual camera system during scoliosis surgery.

    PubMed

    Salmingo, Remel Alingalan; Tadano, Shigeru; Abe, Yuichiro; Ito, Manabu

    2016-05-12

    Treatment for severe scoliosis is usually attained when the scoliotic spine is deformed and fixed by implant rods. Investigation of the intraoperative changes of implant rod shape in three-dimensions is necessary to understand the biomechanics of scoliosis correction, establish consensus of the treatment, and achieve the optimal outcome. The objective of this study was to measure the intraoperative three-dimensional geometry and deformation of implant rod during scoliosis corrective surgery.A pair of images was obtained intraoperatively by the dual camera system before rotation and after rotation of rods during scoliosis surgery. The three-dimensional implant rod geometry before implantation was measured directly by the surgeon and after surgery using a CT scanner. The images of rods were reconstructed in three-dimensions using quintic polynomial functions. The implant rod deformation was evaluated using the angle between the two three-dimensional tangent vectors measured at the ends of the implant rod.The implant rods at the concave side were significantly deformed during surgery. The highest rod deformation was found after the rotation of rods. The implant curvature regained after the surgical treatment.Careful intraoperative rod maneuver is important to achieve a safe clinical outcome because the intraoperative forces could be higher than the postoperative forces. Continuous scoliosis correction was observed as indicated by the regain of the implant rod curvature after surgery. PMID:27175467

  2. Restoration of Vision with Ectopic Expression of Human Rod Opsin.

    PubMed

    Cehajic-Kapetanovic, Jasmina; Eleftheriou, Cyril; Allen, Annette E; Milosavljevic, Nina; Pienaar, Abigail; Bedford, Robert; Davis, Katherine E; Bishop, Paul N; Lucas, Robert J

    2015-08-17

    Many retinal dystrophies result in photoreceptor loss, but the inner retinal neurons can survive, making them potentially amenable to emerging optogenetic therapies. Here, we show that ectopically expressed human rod opsin, driven by either a non-selective or ON-bipolar cell-specific promoter, can function outside native photoreceptors and restore visual function in a mouse model of advanced retinal degeneration. Electrophysiological recordings from retinal explants and the visual thalamus revealed changes in firing (increases and decreases) induced by simple light pulses, luminance increases, and naturalistic movies in treated mice. These responses could be elicited at light intensities within the physiological range and substantially below those required by other optogenetic strategies. Mice with rod opsin expression driven by the ON-bipolar specific promoter displayed behavioral responses to increases in luminance, flicker, coarse spatial patterns, and elements of a natural movie at levels of contrast and illuminance (≈50-100 lux) typical of natural indoor environments. These data reveal that virally mediated ectopic expression of human rod opsin can restore vision under natural viewing conditions and at moderate light intensities. Given the inherent advantages in employing a human protein, the simplicity of this intervention, and the quality of vision restored, we suggest that rod opsin merits consideration as an optogenetic actuator for treating patients with advanced retinal degeneration. PMID:26234216

  3. 21 CFR 888.3020 - Intramedullary fixation rod.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Intramedullary fixation rod. 888.3020 Section 888.3020 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... (bone marrow) canal of long bones for the fixation of fractures. (b) Classification. Class II....

  4. Visual inspections of N Reactor horizontal control rod channels

    SciTech Connect

    Woodruff, E.M.

    1990-09-01

    Safety surveillance is performed in horizontal control rod (HCR) channels to locate conditions which could slow or block rod travel. The findings guide the application of preventive measures to assure eventual rod motion impairment will not occur. Borescopes and, more recently, miniaturized closed circuit television (CCTV) cameras have been used for these examinations. Inspections and measurement results are documented in annual surveillance reports, however reported CCTV observations have been limited to highlights. The objective of this report is to catalogue the CCTV recordings in a format suitable for analysis and interpretation and to ease the access to any desired location by noting tape counter readings corresponding with each tube block in view. Searching file tapes for conditions in a specific areas in the past required counting blocks as they passed the camera to determine the distance from a feature like the edge of the reflector or a steam vent gap. This report adds the observations from recent rod channel inspections (1987 and 1988) to a comprehensive survey of graphite conditions in the moderator and reflector regions of the N Reactor core. When completed, the stand-by status of graphite components will be available for use in restart or decommissioning deliberations.

  5. Consistent tangent operator for an exact Kirchhoff rod model

    NASA Astrophysics Data System (ADS)

    Greco, L.; Cuomo, M.

    2015-09-01

    In the paper, it is considered an exact spatial Kirchhoff rod structural model. The configuration space for this model that has dimension 4 is obtained considering an ad hoc split of the rotation operator that implicitly enforces the constraints on the directors. The tangent stiffness operator, essential for the nonlinear numerical simulations, has been studied. It has been obtained as second covariant gradient of the internal energy functional for the considered structural model that preserves symmetry for any configuration, either equilibrated or not. The result has been reached evaluating the Levi- Civita connection for the tangent space of the configuration manifold. The results obtained extend to the case of Kirchoff - Love rods those presented by Simo (Comput Methods Appl Mech Eng 49:55-70, 1985) for Timoshenko rods. Given the different structure of the tangent spaces in this case, it has been necessary to introduce a specific metric that accounts for the rotation of the intrinsic triad due to the change of the position of the centroid axis of the rod.

  6. 77 FR 1504 - Stainless Steel Wire Rod From India

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-01-10

    ... Commission instituted this review on July 1, 2011 (76 FR 38686) and determined on October 4, 2011, that it would conduct an expedited review (76 FR 64105, October 17, 2011). The Commission transmitted its... COMMISSION Stainless Steel Wire Rod From India Determination On the basis of the record \\1\\ developed in...

  7. Prosthetic Hand For Holding Rods, Tools, And Handles

    NASA Technical Reports Server (NTRS)

    Belcher, Jewell G., Jr.; Vest, Thomas W.

    1995-01-01

    Prosthetic hand with quick-grip/quick-release lever broadens range of specialized functions available to lower-arm amputee by providing improved capabilities for gripping rods, tools, handles, and like. Includes two stationary lower fingers opposed by one pivoting upper finger. Lever operates in conjunction with attached bracket.

  8. Second Language Acquisition Research: A Response to Rod Ellis.

    ERIC Educational Resources Information Center

    Hopkins, Diana; Nettle, Mark

    1994-01-01

    Two practicing English-as-a-Foreign-Language (EFL teachers respond to Rod Ellis' January 1993 article in "ELT Journal," which discussed importance of grammar instruction in EFL classrooms. Argues some of Ellis' assumptions about current classroom practices are inaccurate and a number of his "alternative" approaches to teaching grammar, such as…

  9. Rod and dish cathode improves penning-type vacuum gage

    NASA Technical Reports Server (NTRS)

    Peppin, G. B.

    1966-01-01

    Improved penning-type ionization gage provides range and sensitivity required to measure gas pressure below .01 torr under high vacuum conditions. The gage uses a highly conductive cathode composed of two disks of high magnetic permeability separated by a rod of low magnetic permeability.

  10. Efficient wide-aperture neodymium glass rod amplifiers

    SciTech Connect

    Potemkin, A K; Zhurin, K A; Kirsanov, A V; Kopelovich, E A; Kuznetsov, M V; Kuz'min, A A; Flat, F A; Khazanov, Efim A; Shaikin, A A

    2011-06-30

    Amplifiers based on neodymium phosphate glass rods 60 - 100 mm in diameter are experimentally studied. The amplifiers are pumped by INP-16/250 tubular flash lamps placed in a universal pump cavity with a two-section mirror reflector. A compact high-voltage capacitive energy storage with a preionisation circuit was developed to supply the lamps. (lasers)

  11. 32 CFR 989.21 - Record of decision (ROD).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... adequacy, and forwards it to either SAF/IEE or SAF/AQR, as the case may be, for approval and designation of the signator. A ROD (40 CFR 1505.2) is a concise public document stating what an agency's decision...

  12. 32 CFR 989.21 - Record of decision (ROD).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... adequacy, and forwards it to either SAF/IEI or SAF/AQR, as the case may be, for approval and designation of the signator. A ROD (40 CFR 1505.2) is a concise public document stating what an agency's decision...

  13. 32 CFR 989.21 - Record of decision (ROD).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... adequacy, and forwards it to either SAF/IEE or SAF/AQR, as the case may be, for approval and designation of the signator. A ROD (40 CFR 1505.2) is a concise public document stating what an agency's decision...

  14. 49 CFR 230.93 - Pistons and piston rods.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Pistons and piston rods. 230.93 Section 230.93 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS Steam Locomotives...

  15. Detail of center of swing span rotation. Forty (40) rods ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Detail of center of swing span rotation. Forty (40) rods radiate out from a center cap stand (like spokes on a bicycle) and hold 40 20-inch diameter wheels onto a rim bearing circular track on which they roll when swing span is opened and closed. - Bridgeport Swing Span Bridge, Spanning Tennessee River, Bridgeport, Jackson County, AL

  16. Sparing the Rod: What Teachers Need to Know about Grammar.

    ERIC Educational Resources Information Center

    Cameron, Deborah

    1997-01-01

    Opines that what teachers need to know about grammar is how to teach it without resorting either literally or figuratively to the "cane and the birch rod." Finds that teachers need to look again at the "what" and the "why": what grammar is and why it is taught. Also considers answers given by others. (PA)

  17. Safety rod/thimble melt failure characterization experiments

    SciTech Connect

    Stoots, C.M.; Hawkes, G.L.

    1992-05-01

    The Department of Energy (DOE) requested that he INEL perform experiments to study the thermal failure characteristics of a simulated Savannah River Site nuclear reactor safety rod and its surrounding thimble assembly. An electrically heated stainless steel rod simulated a reactor safety rod located eccentrically or concentrically within a perforated aluminum guide tube or thimble. A total of 37 experiments were conducted for a range of power levels and safety rod/thimble relative orientations. Video tapes were made of the four failure tests that were conducted to the melting point of the thimble. Although the primary emphasis of the experiments were to characterize the melting of the thimble qualitatively, experimental transient measurements included heater voltage and current, heater surface temperatures, aluminum thimble temperatures, and ambient temperature. Numerical studies were also performed in support of the experiments and data interpretation. Two finite element models were created to model the heat conduction-radiation between the stainless steel heater and thimble. The predicted temperatures were in good agreement with the experimental results.

  18. 34. INTERIOR VIEW, SAME AS ABOVE WITH THE FEEDER ROD ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    34. INTERIOR VIEW, SAME AS ABOVE WITH THE FEEDER ROD BEING OFFERED INTO THE MACHINE; UNLIKE THE OTHER NAIL CUTTING MACHINES, THE NAIL PLATE MUST BE HAND FLIPPED AND HAND FED WITH THIS MACHINE - LaBelle Iron Works, Thirtieth & Wood Streets, Wheeling, Ohio County, WV

  19. Nonlinear optical properties of rigid-rod polymers

    NASA Technical Reports Server (NTRS)

    Trimmer, Mark S.; Wang, Ying

    1992-01-01

    The purpose of this research project was to integrate enhanced third order nonlinear optical (NLO) properties, especially high x(exp (3)) (greater than 10(exp -8) esu), into Maxdem's novel conjugated rigid-rod polymers while retaining their desirable processing, mechanical, and thermal properties. This work primarily involved synthetic approaches to optimized materials.

  20. Thermophysical Characteristics of the Protective Coating of the Soldering Rod

    NASA Astrophysics Data System (ADS)

    Shtennikov, V. N.

    2015-01-01

    An analytical dependence of the change in the soldering temperature on the material, thickness of the soldering rod protective coating, and the time of soldering is obtained. The relation derived allows one to ensure the needed temperature of contact soldering of electronic and electrical-engineering components and, consequently, their high quality.

  1. Fabrication of control rods for the High Flux Isotope Reactor

    SciTech Connect

    Sease, J.D.

    1998-03-01

    The High Flux Isotope Reactor (HFIR) is a research-type nuclear reactor that was designed and built in the early 1960s and has been in continuous operation since its initial criticality in 1965. Under current plans, the HFIR is expected to continue in operation until 2035. This report updates ORNL/TM-9365, Fabrication Procedure for HFIR Control Plates, which was mainly prepared in the early 1970's but was not issued until 1984, and reflects process changes, lessons learned in the latest control rod fabrication campaign, and suggested process improvements to be considered in future campaigns. Most of the personnel involved with the initial development of the processes and in part campaigns have retired or will retire soon. Because their unlikely availability in future campaigns, emphasis has been placed on providing some explanation of why the processes were selected and some discussions about the importance of controlling critical process parameters. Contained in this report is a description of the function of control rods in the reactor, the brief history of the development of control rod fabrication processes, and a description of procedures used in the fabrication of control rods. A listing of the controlled documents and procedures used in the last fabrication campaigns is referenced in Appendix A.

  2. A Call for Powerful Leaders: A Conversation with Rod Paige

    ERIC Educational Resources Information Center

    Scherer, Marge

    2004-01-01

    Rod Paige, US Secretary of Education, and former superintendent of schools in Houston narrates his vision for US schools and the need for leadership in educational institutions. He defends the controversial No Child Left Behind Act and feels that each leader is responsible for ensuring that the students receive first-class education in all of the…

  3. Average refractive powers of an alexandrite laser rod

    NASA Astrophysics Data System (ADS)

    Driedger, K. P.; Krause, W.; Weber, H.

    1986-04-01

    The average refractive powers (average inverse focal lengths) of the thermal lens produced by an alexandrite laser rod optically pumped at repetition rates between 0.4 and 10 Hz and with electrical flashlamp input pulse energies up to 500 J have been measured. The measuring setup is described and the measurement results are discussed.

  4. VIEW OF EAST GUN EMPLACEMENT. NOTE THE STEEL REINFORCING RODS ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    VIEW OF EAST GUN EMPLACEMENT. NOTE THE STEEL REINFORCING RODS PROTRUDING FROM THE BROKEN TOP OF THE RETAINING WALL. VIEW FACING NORTHEAST - U.S. Naval Base, Pearl Harbor, Ford Island 5-Inch Antiaircraft Battery, East Gun Emplacement, Ford Island, Pearl City, Honolulu County, HI

  5. Glutamine deprivation initiates reversible assembly of mammalian rods and rings.

    PubMed

    Calise, S John; Carcamo, Wendy C; Krueger, Claire; Yin, Joyce D; Purich, Daniel L; Chan, Edward K L

    2014-08-01

    Rods and rings (RR) are protein assemblies composed of cytidine triphosphate synthetase type 1 (CTPS1) and inosine monophosphate dehydrogenase type 2 (IMPDH2), key enzymes in CTP and GTP biosynthesis. Small-molecule inhibitors of CTPS1 or IMPDH2 induce RR assembly in various cancer cell lines within 15 min to hours. Since glutamine is an essential amide nitrogen donor in these nucleotide biosynthetic pathways, glutamine deprivation was examined to determine whether it leads to RR formation. HeLa cells cultured in normal conditions did not show RR, but after culturing in media lacking glutamine, short rods (<2 μm) assembled after 24 h, and longer rods (>5 μm) formed after 48 h. Upon supplementation with glutamine or guanosine, these RR underwent almost complete disassembly within 15 min. Inhibition of glutamine synthetase with methionine sulfoximine also increased RR assembly in cells deprived of glutamine. Taken together, our data support the hypothesis that CTP/GTP biosynthetic enzymes polymerize to form RR in response to a decreased intracellular level of glutamine. We speculate that rod and ring formation is an adaptive metabolic response linked to disruption of glutamine homeostasis. PMID:24477477

  6. Random Breakage of a Rod into Unit Lengths

    ERIC Educational Resources Information Center

    Gani, Joe; Swift, Randall

    2011-01-01

    In this article we consider the random breakage of a rod into "L" unit elements and present a Markov chain based method that tracks intermediate breakage configurations. The probability of the time to final breakage for L = 3, 4, 5 is obtained and the method is shown to extend in principle, beyond L = 5.

  7. Electric Field Driven Self-Assembly of Colloidal Rods

    NASA Astrophysics Data System (ADS)

    Juarez, Jaime; Chaudhary, Kundan; Chen, Qian; Granick, Steve; Lewis, Jennifer

    2012-02-01

    The ability to assemble anisotropic colloidal building blocks into ordered configurations is of both scientific and technological importance. We are studying how electric field-induced interactions guide the self-assembly of these blocks into well aligned microstructures. Specifically, we present observations of the assembly of colloidal silica rods (L/D ˜ 4) within planar electrode cells as a function of different electric field parameters. Results from video microscopy and image analysis demonstrate that aligned microstructures form due to the competition between equilibrium interactions of induced dipoles and non-equilibrium processes (i.e., electro-osmosis). Under the appropriate electric field conditions (˜ kHZ AC fields), aligned colloidal rod fluids form over large areas on the electrode surface. The superposition of a DC electric field to this aligned colloidal rod fluid initiates their condensation into a vertically oriented crystalline phase. Ongoing work is now focused on exploring how temporal changes to electric fields influence colloidal rod dynamics and, hence, the assembly kinetics of aligned colloidal monolayers.

  8. 14. Photographic copy of photocopy of bridge drawing, reinforced rod ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    14. Photographic copy of photocopy of bridge drawing, reinforced rod specifications (June 12, 1937, original drawing on file in Structures Section, Utah Department of Transportation, Salt Lake City, Utah). SHEET NO. 6 OF 6 SHEETS. - Gould Wash Bridge, Spanning Gould Wash at State Route 9, Hurricane, Washington County, UT

  9. Flexible Stabilisation of the Degenerative Lumbar Spine Using PEEK Rods

    PubMed Central

    Benezech, Jacques; Garlenq, Bruno; Larroque, Gilles

    2016-01-01

    Posterior lumbar interbody fusion using cages, titanium rods, and pedicle screws is considered today as the gold standard of surgical treatment of lumbar degenerative disease and has produced satisfying long-term fusion rates. However this rigid material could change the physiological distribution of load at the instrumental and adjacent segments, a main cause of implant failure and adjacent segment disease, responsible for a high rate of further surgery in the following years. More recently, semirigid instrumentation systems using rods made of polyetheretherketone (PEEK) have been introduced. This clinical study of 21 patients focuses on the clinical and radiological outcomes of patients with lumbar degenerative disease treated with Initial VEOS PEEK®-Optima system (Innov'Spine, France) composed of rods made from PEEK-OPTIMA® polymer (Invibio Biomaterial Solutions, UK) without arthrodesis. With an average follow-up of 2 years and half, the chances of reoperation were significantly reduced (4.8%), quality of life was improved (ODI = 16%), and the adjacent disc was preserved in more than 70% of cases. Based on these results, combined with the biomechanical and clinical data already published, PEEK rods systems can be considered as a safe and effective alternative solution to rigid ones. PMID:26981285

  10. Restoration of Vision with Ectopic Expression of Human Rod Opsin

    PubMed Central

    Cehajic-Kapetanovic, Jasmina; Eleftheriou, Cyril; Allen, Annette E.; Milosavljevic, Nina; Pienaar, Abigail; Bedford, Robert; Davis, Katherine E.; Bishop, Paul N.; Lucas, Robert J.

    2015-01-01

    Summary Many retinal dystrophies result in photoreceptor loss, but the inner retinal neurons can survive, making them potentially amenable to emerging optogenetic therapies. Here, we show that ectopically expressed human rod opsin, driven by either a non-selective or ON-bipolar cell-specific promoter, can function outside native photoreceptors and restore visual function in a mouse model of advanced retinal degeneration. Electrophysiological recordings from retinal explants and the visual thalamus revealed changes in firing (increases and decreases) induced by simple light pulses, luminance increases, and naturalistic movies in treated mice. These responses could be elicited at light intensities within the physiological range and substantially below those required by other optogenetic strategies. Mice with rod opsin expression driven by the ON-bipolar specific promoter displayed behavioral responses to increases in luminance, flicker, coarse spatial patterns, and elements of a natural movie at levels of contrast and illuminance (≈50–100 lux) typical of natural indoor environments. These data reveal that virally mediated ectopic expression of human rod opsin can restore vision under natural viewing conditions and at moderate light intensities. Given the inherent advantages in employing a human protein, the simplicity of this intervention, and the quality of vision restored, we suggest that rod opsin merits consideration as an optogenetic actuator for treating patients with advanced retinal degeneration. PMID:26234216

  11. Microgravity Flammability of PMMA Rods in Concurrent Flow

    NASA Technical Reports Server (NTRS)

    Olson, Sandra L.; Ferkul, Paul V.

    2015-01-01

    Microgravity experiments burning cast PMMA cylindrical rods in axial flow have been conducted aboard the International Space Station in the Microgravity Science Glovebox (MSG) facility using the Burning and Suppression of Solids (BASS) flow duct, as part of the BASS-II experiment. Twenty-four concurrent-flow tests were performed, focusing on finding flammability limits as a function of oxygen and flow speed. The oxygen was varied by using gaseous nitrogen to vitiate the working volume of the MSG. The speed of the flow parallel to the rod was varied using a fan at the entrance to the duct. Both blowoff and quenching limits were obtained at several oxygen concentrations. Each experiment ignited the rod at the initially hemispherical stagnation tip of the rod, and allowed the flame to develop and heat the rod at a sufficient flow to sustain burning. For blowoff limit tests, the astronaut quickly turned up the flow to obtain extinction. Complementary 5.18-second Zero Gravity Facility drop tests were conducted to compare blowoff limits in short and long duration microgravity. For quenching tests, the flow was incrementally turned down and the flame allowed to stabilize at the new flow condition for at least the solid-phase response time before changing it again. Quenching was observed when the flow became sufficiently weak that the flame could no longer provide adequate heat flux to compensate for the heat losses (conduction into the rod and radiation). A surface energy balance is presented that shows the surface radiative loss exceeds the conductive loss into the rod near the limit. The flammability boundary is shown to represent a critical Damkohler number, expressed in terms of the reaction rate divided by the stretch rate. For the blowoff branch, the boundary exhibits a linear dependence on oxygen concentration and stretch rate, indicating that the temperature at blowoff must be fairly constant. For the quenching branch, the dominance of the exponential nature of

  12. Ultrasonic monitoring of material processing using clad buffer rod sensors

    NASA Astrophysics Data System (ADS)

    Ramos Franca, Demartonne

    Ultrasonic sensors and techniques are developed for in-line monitoring of polymer extrusion, cleanliness of molten metals and liquid flow speed at elevated temperature. Pulse-echo mode is used for the first two processes, while the through-transmission mode is applied in the third one. The ultrasonic probe consists of high performance clad buffer rods with different dimensions to thermally isolate the commercial ultrasonic transducer from materials at high temperature. The clad buffer rods are made of steel, polymer and ceramic. Steel clad buffer rods are introduced for in-line monitoring of polymer extrusion processes. Owing to its superior performance in pulse-echo mode, for the first time such a probe is installed and performs ultrasonic monitoring in the die of a co-extrusion machine and in the barrel section of a twin-screw extruder. It can reveal a variety of information relevant to process parameters, such as polymer layer thickness, interface location and adhesion quality, stability, or polymer composition change. For the ultrasonic monitoring of polymer processes, probes with acoustic impedance that matches that of the processed polymer may offer certain advantages such as quantitative viscoelastic evaluation; thus high temperature polymer clad buffer rods, in particular PEEK, are developed. It is demonstrated that this new probe exhibits unique advantages for in-line monitoring of the cure of epoxies and polymer extrusion process. Long steel clad buffer rods with a spherical focus lens machined at the probing end are proposed for cleanliness evaluation of molten metals. The potential of this focusing probe is demonstrated by means of high-resolution imaging and particles detection in molten zinc at temperatures higher than 600°C, using a single probe operated at pulse-echo mode. A contrapropagating ultrasonic flowmeter employing steel clad buffer rods is devised to operate at high temperature. It is demonstrated that these rods guide ultrasonic signals

  13. Coolant mixing in LMFBR rod bundles and outlet plenum mixing transients. Progress report, March 1, 1980-May 31, 1980

    SciTech Connect

    Todreas, N.E.; Golay, M.W.; Wolf, L.

    1980-01-01

    Experimental and theoretical work is reported on four tasks: bundle geometry (wrapped and bare rods), subchannel geometry (bare rods), LMFBR outlet plenum flow mixing, and theoretical local temperature files in LMFBR fuel rod bundles. (DLC)

  14. RECOVERY OF ROD PHOTORESPONSES IN ABCR-DEFICIENT MICE

    PubMed Central

    Pawar, Ambarish S.; Qtaishat, Nasser M.; Little, Deborah M.; Pepperberg, David R.

    2010-01-01

    Purpose ABCR protein in the rod outer segment is thought to facilitate movement of the all-trans retinal photoproduct of rhodopsin bleaching out of the disk lumen. We investigated the extent to which ABCR deficiency affects post-bleach recovery of the rod photoresponse in ABCR-deficient (abcr−/−) mice. Methods Electroretinographic (ERG) a-wave responses were recorded from abcr−/− mice and two control strains. Using a bright probe flash, we examined the course of rod recovery following fractional rhodopsin bleaches of ~10−6, ~3×10−5, ~0.03 and ~0.30–0.40. Results Dark-adapted abcr−/− mice and controls exhibited similar normalized near-peak amplitudes of the paired-flash-ERG-derived, weak-flash response. Response recovery following ~10−6 bleaching exhibited an average exponential time constant of 319, 171 and 213 ms, respectively, in the abcr−/− and the two control strains. Recovery time constants determined for ~3×10−5 bleaching did not differ significantly among strains. However, those determined for the ~0.03 bleach indicated significantly faster recovery in abcr−/− (2.34 ± 0.74 min) than in the controls (5.36 ± 2.20 min, and 5.92 ± 2.44 min). Following ~0.30–0.40 bleaching, the initial recovery in the abcr−/− was on average faster than in controls. Conclusions By comparison with controls, abcr−/− mice exhibit faster rod recovery following a bleach of ~0.03. The data suggest that ABCR in normal rods may directly or indirectly prolong all-trans retinal clearance from the disk lumen over a significant bleaching range, and that the essential function of ABCR may be to promote the clearance of residual amounts of all-trans retinal that remain in the disks long after bleaching. PMID:18263807

  15. Mechanical behavior of enamel rods under micro-compression.

    PubMed

    Yilmaz, Ezgi D; Schneider, Gerold A

    2016-10-01

    Exploring the structural strategies behind the optimized mechanical performance of hierarchical materials has been a focal point of extensive research over the past decades. Dental enamel is one such natural material, comprising a complicated hierarchical structure with a high level of mineral content. Bundles of hydroxyapatite nanofibers (level-1) Ø: 50nm form enamel rods (level-2) Ø: 5µm, which constitute bands (level-3) Ø: 50µm. While a number of studies in the last decade using advanced fracture mechanical methods have revealed an increasing trend in the fracture toughness of enamel with each additional level of hierarchy, there is still no general agreement on how hierarchical structuring affects the stiffness and strength of enamel. In this study, we identified the stiffness and strength values of the isolated rods (level-2) via micro-compression. The rods were tested in three different orientations with respect to the loading direction: parallel, perpendicular and oblique. The highest stress level withstood before catastrophic fracture was observed to be ~1500MPa in perpendicular orientation. In the oblique loading, the specimens failed by shearing and exhibited a damage-tolerant deformation behavior, which was attributed to the conjugation spots identified between the rods and interrod sheets. The elastic modulus was ~60GPa on average and similar in all orientations. The isotropy in stiffness was attributed to the mineral contacts residing between rods. This was verified by an analytical model derived for level-1 and extended over higher hierarchical levels. The experimental results obtained at level-2 were comparable to the compressive strength and stiffness values reported for level-1 and bulk enamel in the literature. In general, our results suggest that hierarchy has only a minor influence on the compressive properties of enamel. PMID:27415405

  16. Reversible Bending Fatigue Testing on Zry-4 Surrogate Rods

    SciTech Connect

    Wang, Jy-An John; Wang, Hong; Bevard, Bruce Balkcom; Howard, Rob L

    2014-01-01

    Testing high-burnup spent nuclear fuel (SNF) presents many challenges in areas such as specimen preparation, specimen installation, mechanical loading, load control, measurements, data acquisition, and specimen disposal because these tasks are complicated by the radioactivity of the test specimens. Research and comparison studies conducted at Oak Ridge National Laboratory (ORNL) resulted in a new concept in 2010 for a U-frame testing setup on which to perform hot-cell reversible bending fatigue testing. Subsequently, the three-dimensional finite element analysis and the engineering design of components were completed. In 2013 the ORNL team finalized the upgrade of the U-frame testing setup and the integration of the U-frame setup into a Bose dual linear motor test bench to develop a cyclic integrated reversible-bending fatigue tester (CIRFT). A final check was conducted on the CIRFT test system in August 2013, and the CIRFT was installed in the hot cell in September 2013 to evaluate both the static and dynamic mechanical response of SNF rods under simulated loads. The fatigue responses of Zircaloy-4 (Zry-4) cladding and the role of pellet pellet and pellet clad interactions are critical to SNF vibration integrity, but such data are not available due to the unavailability of an effective testing system. While the deployment of the developed CIRFT test system in a hot cell will provide the opportunity to generate the data, the use of a surrogate rod has proven quite effective in identifying the underlying deformation mechanism of an SNF composite rod under an equivalent loading condition. This paper presents the experimental results of using surrogate rods under CIRFT reversible cyclic loading. Specifically, monotonic and cyclic bending tests were conducted on surrogate rods made of a Zry-4 tube and alumina pellet inserts, both with and without an epoxy bond.

  17. Nonlinear dynamics of a flexible mechanism with impact

    NASA Astrophysics Data System (ADS)

    Dupac, Mihai; Marghitu, Dan B.

    2006-02-01

    The nonlinear dynamics of a slider-crank mechanism with a flexible rod is considered in this study. The flexible rod is modeled with lumped masses and periodically impacted by an external flexible sphere. The impact is modeled using a kinematic coefficient of restitution. Nonlinear dynamics tools are applied to analyze the simulated data captured from the connecting rod of the mechanism. The chaotic behavior of the system is analyzed. The stability of the motion is studied using the Lyapunov exponents. The dependence between the Lyapunov exponents and the corresponding angular velocity of the driver link of the mechanism is investigated.

  18. Method of increasing magnetostrictive response of rare earth-iron alloy rods

    DOEpatents

    Verhoeven, J.D.; McMasters, O.D.; Gibson, E.D.; Ostenson, J.E.; Finnemore, D.K.

    1989-04-04

    This invention comprises a method of increasing the magnetostrictive response of rare earth-iron (RFe) magnetostrictive alloy rods by a thermal-magnetic treatment. The rod is heated to a temperature above its Curie temperature, viz. from 400 to 600 C; and, while the rod is at that temperature, a magnetic field is directionally applied and maintained while the rod is cooled, at least below its Curie temperature. 2 figs.

  19. Method of increasing magnetostrictive response of rare earth-iron alloy rods

    DOEpatents

    Verhoeven, John D.; McMasters, O. Dale; Gibson, Edwin D.; Ostenson, Jerome E.; Finnemore, Douglas K.

    1989-04-04

    This invention comprises a method of increasing the magnetostrictive response of rare earth-iron (RFe) magnetostrictive alloy rods by a thermal-magnetic treatment. The rod is heated to a temperature above its Curie temperature, viz. from 400.degree. to 600.degree. C.; and, while the rod is at that temperature, a magnetic field is directionally applied and maintained while the rod is cooled, at least below its Curie temperature.

  20. Control rod system useable for fuel handling in a gas-cooled nuclear reactor

    DOEpatents

    Spurrier, Francis R.

    1976-11-30

    A control rod and its associated drive are used to elevate a complete stack of fuel blocks to a position above the core of a gas-cooled nuclear reactor. A fuel-handling machine grasps the control rod and the drive is unlatched from the rod. The stack and rod are transferred out of the reactor, or to a new location in the reactor, by the fuel-handling machine.

  1. Linear motion device and method for inserting and withdrawing control rods

    DOEpatents

    Smith, J.E.

    Disclosed is a linear motion device and more specifically a control rod drive mechanism (CRDM) for inserting and withdrawing control rods into a reactor core. The CRDM and method disclosed is capable of independently and sequentially positioning two sets of control rods with a single motor stator and rotor. The CRDM disclosed can control more than one control rod lead screw without incurring a substantial increase in the size of the mechanism.

  2. Nanoparticle-Induced Ellipse-to-Vesicle Morphology Transition of Rod-Coil-Rod Triblock Copolymer Aggregates.

    PubMed

    Yang, Chaoying; Li, Qing; Cai, Chunhua; Lin, Jiaping

    2016-07-12

    Cooperative self-assembly behavior of rod-coil-rod poly(γ-benzyl-l-glutamate)-block-poly(ethylene glycol)-block-poly(γ-benzyl-l-glutamate) (PBLG-b-PEG-b-PBLG) amphiphilic triblock copolymers and hydrophobic gold nanoparticles (AuNPs) was investigated by both experiments and dissipative particle dynamics (DPD) simulations. It was discovered that pure PBLG-b-PEG-b-PBLG copolymers self-assemble into ellipse-like aggregates, and the morphology transforms into vesicles as AuNPs are introduced. When the hydrophobicity of AuNPs is close to that of the copolymers, AuNPs are homogeneously distributed in the vesicle wall. While for the AuNPs with higher hydrophobicity, they are embedded in the vesicle wall as clusters. In addition to the experimental observations, DPD simulations were performed on the self-assembly behavior of triblock copolymer/nanoparticle mixtures. Simulations well reproduced the morphology transition observed in the experiments and provided additional information such as chain packing mode in aggregates. It is deduced that the main reason for the ellipse-to-vesicle transition of the aggregates is attributed to the breakage of ordered and dense packing of PBLG rods in the aggregate core by encapsulating AuNPs. This study deepens our understanding of the self-assembly behavior of rod-coil copolymer/nanoparticle mixtures and provides strategy for designing hybrid polypeptide nanostructures. PMID:27314970

  3. Airflow produced by dielectric barrier discharge between asymmetric parallel rod electrodes

    SciTech Connect

    Hayashi, Kazuo; Tanaka, Motofumi; Yasui, Hiroyuki; Hashimoto, Kiyoshi

    2007-09-15

    We observed a novel type of airflow produced by an atmospheric rf discharge between asymmetric parallel rod electrodes. The electrodes were a bare metal rod 1 mm in diameter and a glass-coated metal rod 3.2 mm in diameter. The thrust, measured by a pendulum, increased with discharge input power.

  4. Implementation of CTRLPOS, a VENTURE module for control rod position criticality searches, control rod worth curve calculations, and general criticality searches

    SciTech Connect

    Smith, L.A.; Renier, J.P.

    1994-06-01

    A module in the VENTURE reactor analysis code system, CTRLPOS, is developed to position control rods and perform control rod position criticality searches. The module is variably dimensioned so that calculations can be performed with any number of control rod banks each having any number of control rods. CTRLPOS can also calculate control rod worth curves for a single control rod or a bank of control rods. Control rod depletion can be calculated to provide radiation source terms. These radiation source terms can be used to predict radiation doses to personnel and estimate the shielding and long-term storage requirements for spent control rods. All of these operations are completely automated. The numerous features of the module are discussed in detail. The necessary input data for the CTRLPOS module is explained. Several sample problems are presented to show the flexibility of the module. The results presented with the sample problems show that the CTRLPOS module is a powerful tool which allows a wide variety of calculations to be easily performed.

  5. Direct rod input to cone BCs and direct cone input to rod BCs challenge the traditional view of mammalian BC circuitry

    PubMed Central

    Pang, Ji-Jie; Gao, Fan; Lem, Janis; Bramblett, Debra E.; Paul, David L.; Wu, Samuel M.

    2009-01-01

    Bipolar cells are the central neurons of the retina that transmit visual signals from rod and cone photoreceptors to third-order neurons in the inner retina and the brain. A dogma set forth by early anatomical studies is that bipolar cells in mammalian retinas receive segregated rod/cone synaptic inputs (either from rods or from cones), and here, we present evidence that challenges this traditional view. By analyzing light-evoked cation currents from morphologically identified depolarizing bipolar cells (DBCs) in the wild-type and three pathway-specific knockout mice (rod transducin knockout [Trα−/−], connexin36 knockout [Cx36−/−], and transcription factor beta4 knockout [Bhlhb4−/−]), we show that a subpopulation of rod DBCs (DBCR2s) receives substantial input directly from cones and a subpopulation of cone DBCs (DBCC1s) receives substantial input directly from rods. These results provide evidence of the existence of functional rod-DBCC and cone-DBCR synaptic pathways in the mouse retina as well as the previously proposed rod hyperpolarizing bipolar-cells pathway. This is grounds for revising the mammalian rod/cone bipolar cell dogma. PMID:20018684

  6. Analytical modeling of the buffeting of a rod in axial flow. [PWR; BWR

    SciTech Connect

    Lin, W.H.; Wamsganss, M.W.

    1981-12-01

    Turbulent buffeting of a circular, flexible rod in axial flows is reported. The main excitation mechanisms are turbulent wall-pressure fluctuations and the motion-dependent force field caused by the rod motion. On the assumption that the turbulent wall-pressure fluctuations are independent of rod motion, a linear forced vibration model is proposed to compute the buffeting displacement of the rod with the aid of empirical constants determined from experimental measurements of wall-pressure fluctuations. Predicted and measured values of the root-mean-square rod displacement are shown to be in reasonably good agreement.

  7. Relaxation of rod misalignment technical specification requirements: An increased operational flexibility

    SciTech Connect

    John, G.; Leipner-Gomes, C.I.; Johansen, B.J.

    1995-12-31

    The pressurized water reactor technical specification (T/S) limiting condition for operation (LCO) for rod misalignment and rod position indication (RPI) typically requires all rod cluster control assemblies to be positioned with {+-}12 steps of the group demand position. The LCO is approved by the U.S. Nuclear Regulatory Commission (NRC) for use by all Westinghouse plants, and the core design incorporates a peaking factor uncertainty to accommodate potential rod misalignments within this approved LCO. Also, the LCO requires all RPI channels and the demand position indicator system to be operable and capable of determining the control rod position within {+-}12 steps.

  8. Countercurrent flow-limiting characteristics of a Savannah River Plant control rod septifoil

    SciTech Connect

    Anderson, J.L.

    1992-07-01

    Experiments were performed at the Idaho National Engineering Laboratory to investigate the counter-current flow limiting characteristics of a Savannah River Plant control rod septifoil assembly. These experiments were unheated, using air and water as the working fluids. Results are presented in terms of the Wallis flooding correlation for several different control rod configurations. Flooding was observed to occur in the vicinity of the inlet slots/holes of the septifoil, rather than within the rod bundle at the location of the minimum flow area. Nearly identical flooding characteristics of the septifoil were observed for configurations with zero, three, and four rods inserted, but significantly different results occurred with 5 rods inserted.

  9. Optical polarization properties of InAs/InP quantum dot and quantum rod nanowires.

    PubMed

    Anufriev, Roman; Barakat, Jean-Baptiste; Patriarche, Gilles; Letartre, Xavier; Bru-Chevallier, Catherine; Harmand, Jean-Christophe; Gendry, Michel; Chauvin, Nicolas

    2015-10-01

    The emission polarization of single InAs/InP quantum dot (QD) and quantum rod (QR) nanowires is investigated at room temperature. Whereas the emission of the QRs is mainly polarized parallel to the nanowire axis, the opposite behavior is observed for the QDs. These optical properties can be explained by a combination of dielectric effects related to the nanowire geometry and to the configuration of the valence band in the nanostructure. A theoretical model and finite difference in time domain calculations are presented to describe the impact of the nanowire and the surroundings on the optical properties of the emitter. Using this model, the intrinsic degree of linear polarization of the two types of emitters is extracted. The strong polarization anisotropies indicate a valence band mixing in the QRs but not in the QDs. PMID:26349621

  10. Optical polarization properties of InAs/InP quantum dot and quantum rod nanowires

    NASA Astrophysics Data System (ADS)

    Anufriev, Roman; Barakat, Jean-Baptiste; Patriarche, Gilles; Letartre, Xavier; Bru-Chevallier, Catherine; Harmand, Jean-Christophe; Gendry, Michel; Chauvin, Nicolas

    2015-10-01

    The emission polarization of single InAs/InP quantum dot (QD) and quantum rod (QR) nanowires is investigated at room temperature. Whereas the emission of the QRs is mainly polarized parallel to the nanowire axis, the opposite behavior is observed for the QDs. These optical properties can be explained by a combination of dielectric effects related to the nanowire geometry and to the configuration of the valence band in the nanostructure. A theoretical model and finite difference in time domain calculations are presented to describe the impact of the nanowire and the surroundings on the optical properties of the emitter. Using this model, the intrinsic degree of linear polarization of the two types of emitters is extracted. The strong polarization anisotropies indicate a valence band mixing in the QRs but not in the QDs.

  11. Vibrations of beams and rods carrying a moving mass

    NASA Astrophysics Data System (ADS)

    Zhao, X. W.; van der Heijden, G. H. M.; Hu, Z. D.

    2016-05-01

    We study the vibration of slender one-dimensional elastic structures (beams, cables, wires, rods) under the effect of a moving mass or load. We first consider the classical small- deflection (Euler-Bernoulli) beam case, where we look at tip vibrations of a cantilever as a model for a barreled launch system. Then we develop a theory for large deformations based on Cosserat rod theory. We illustrate the effect of moving loads on large-deformation structures with a few cable and arch problems. Large deformations are found to have a resonance detuning effect on the cable. For the arch we find different failure modes depending on its depth: a shallow arch fails by in-plane collapse, while a deep arch fails by sideways flopping. In both cases the speed of the traversing load is found to have a stabilising effect on the structure, with failure suppressed entirely at sufficiently high speed.

  12. Rewetting of hot vertical rod during jet impingement surface cooling

    NASA Astrophysics Data System (ADS)

    Agrawal, Chitranjan; Kumar, Ravi; Gupta, Akhilesh; Chatterjee, Barun

    2016-06-01

    A stainless steel (SS-316) vertical rod of 12 mm diameter at 800 ± 10 °C initial temperature was cooled by normal impinging round water jet. The surface rewetting phenomenon was investigated for a range of jet diameter 2.5-4.8 mm and jet Reynolds number 5000-24,000 using a straight tube type nozzle. The investigation were made from the stagnation point to maximum 40 mm downstream locations, simultaneously for both upside and downside directions. The cooling performance of the vertical rod was evaluated on the basis of rewetting parameters i.e. rewetting temperature, wetting delay, rewetting velocity and the maximum surface heat flux. Two separate Correlations have been proposed for the dimensionless rewetting velocity in terms of rewetting number and the maximum surface heat flux that predicts the experimental data within an error band of ±20 and ±15 % respectively.

  13. Granular gases of rod-shaped grains in microgravity.

    PubMed

    Harth, K; Kornek, U; Trittel, T; Strachauer, U; Höme, S; Will, K; Stannarius, R

    2013-04-01

    Granular gases are convenient model systems to investigate the statistical physics of nonequilibrium systems. In the literature, one finds numerous theoretical predictions, but only few experiments. We study a weakly excited dilute gas of rods, confined in a cuboid container in microgravity during a suborbital rocket flight. With respect to a gas of spherical grains at comparable filling fraction, the mean free path is considerably reduced. This guarantees a dominance of grain-grain collisions over grain-wall collisions. No clustering was observed, unlike in similar experiments with spherical grains. Rod positions and orientations were determined and tracked. Translational and rotational velocity distributions are non-Gaussian. Equipartition of kinetic energy between translations and rotations is violated. PMID:25166993

  14. Rubber shock absorber for deep-well rod operated pumps

    SciTech Connect

    Bagirov, M.M.

    1984-05-01

    Tests of hydropneumatic shock absorbers of deep-well pumps in oil fields showed that they improve the efficiency of the installations by their design is very complicated. Mechanically acting absorbers of dynamic forces are simpler in design. Rubber shock absorbers differ advantageously from spring absorbers in that considerable oscillation-damping forces of any amplitude act in them. The design of a shock absorber is described which is situated under the balance arm of a pumping jack. A prototype of the shock absorber, in which the elastic elements were cylinders made of rubber was tested in a test borehole. Dynamographic recordings made in this borehole in operation with and without shock absorber show that the shock absorber reduces the maximum load on the rods and the double amplitude of load change. Calculations show that when the described shock absorber is used the reduced load is 11-18% smaller. This may considerably reduce the number of breakages of deepwell pump rods.

  15. Overview of Fuel Rod Simulator Usage at ORNL

    SciTech Connect

    Ott, Larry J.; McCulloch, Reg

    2004-02-04

    During the 1970s and early 1980s, the Oak Ridge National Laboratory (ORNL) operated large out-of-reactor experimental facilities to resolve thermal-hydraulic safety issues in nuclear reactors. The fundamental research ranged from material mechanical behavior of fuel cladding during the depressurization phase of a loss-of-coolant accident (LOCA) to basic heat transfer research in gas- or sodium-cooled cores. The largest facility simulated the initial phase (less than 1 min. of transient time) of a LOCA in a commercial pressurized-water reactor. The nonnuclear reactor cores of these facilities were mimicked via advanced, highly instrumented electric fuel rod simulators locally manufactured at ORNL. This paper provides an overview of these experimental facilities with an emphasis on the fuel rod simulators.

  16. High-power dual-rod Yb:YAG laser.

    PubMed

    Honea, E C; Beach, R J; Mitchell, S C; Skidmore, J A; Emanuel, M A; Sutton, S B; Payne, S A; Avizonis, P V; Monroe, R S; Harris, D G

    2000-06-01

    We describe a diode-pumped Yb:YAG laser that produces 1080 W of power cw with 27.5% optical optical efficiency and 532 W Q-switched with M(2)=2.2 and 17% optical-optical efficiency. The laser uses two composite Yb:YAG rods separated by a 90 degrees quartz rotator for bifocusing compensation. A microlensed diode array end pumps each rod, using a hollow lens duct for pump delivery. By changing resonator parameters we can adjust the fundamental mode size and the output beam quality. Using a flattened Gaussian intensity profile to calculate the mode-fill efficiency and clipping losses, we compare experimental data with modeled output power versus beam quality. PMID:18064190

  17. Interaction of Fixed Number of Photons with Retinal Rod Cells

    NASA Astrophysics Data System (ADS)

    Phan, Nam Mai; Cheng, Mei Fun; Bessarab, Dmitri A.; Krivitsky, Leonid A.

    2014-05-01

    New tools and approaches of quantum optics offer a unique opportunity to generate light pulses carrying a precise number of photons. Accurate control over the light pulses helps to improve the characterization of photoinduced processes. Here, we study interaction of a specialized light source which provides flashes containing just one photon, with retinal rod cells of Xenopus laevis toads. We provide unambiguous proof of the single-photon sensitivity of rod cells without relying on the statistical modeling. We determine their quantum efficiencies without the use of any precalibrated detectors and obtain the value of (29±4.7)%. Our approach provides the path for future studies and applications of quantum properties of light in phototransduction, vision, and photosynthesis.

  18. Ideal illuminants for rod/L-cone color

    NASA Astrophysics Data System (ADS)

    McCann, John J.

    2006-01-01

    Humans see multicolor complex images with illuminants that have very low amounts of 400 to 580nm light when there is enough long-wave light greater than 590nm. Interactions between rods and long-wave (L) cones generate these colors. They are observed when there is insufficient light for a threshold response from M- and S-cones. This paper measures the spectral emission of a wood fire and a wax candle and it compares these low-color temperature spectral radiant exitances with the sensitivities of rods and long-wave cones. The paper reviews some of the literature on the evolution of human cone pigments and the early use of fire by hominids.

  19. Terahertz pinch harmonics enabled by single nano rods.

    PubMed

    Park, Hyeong-Ryeol; Bahk, Young-Mi; Choe, Jong Ho; Han, Sanghoon; Choi, Seong Soo; Ahn, Kwang Jun; Park, Namkyoo; Park, Q-Han; Kim, Dai-Sik

    2011-11-21

    A pinch harmonic (or guitar harmonic) is a musical note produced by lightly pressing the thumb of the picking hand upon the string immediately after it is picked [J. Chem. Educ. 84, 1287 (2007)]. This technique turns off the fundamental and all overtones except those with a node at that location. Here we present a terahertz analogue of pinch harmonics, whereby a metallic nano rod placed at a harmonic node on a terahertz nanoresonator suppresses the fundamental mode, making the higher harmonics dominant. Strikingly, a skin depth-wide nano rod placed at the mid-point turns off all resonances. Our work demonstrates that terahertz electromagnetic waves can be tailored by nanoparticles strategically positioned, paving important path towards terahertz switching and detection applications. PMID:22109504

  20. Granular Gases of Rod-Shaped Grains in Microgravity

    NASA Astrophysics Data System (ADS)

    Harth, K.; Kornek, U.; Trittel, T.; Strachauer, U.; Höme, S.; Will, K.; Stannarius, R.

    2013-04-01

    Granular gases are convenient model systems to investigate the statistical physics of nonequilibrium systems. In the literature, one finds numerous theoretical predictions, but only few experiments. We study a weakly excited dilute gas of rods, confined in a cuboid container in microgravity during a suborbital rocket flight. With respect to a gas of spherical grains at comparable filling fraction, the mean free path is considerably reduced. This guarantees a dominance of grain-grain collisions over grain-wall collisions. No clustering was observed, unlike in similar experiments with spherical grains. Rod positions and orientations were determined and tracked. Translational and rotational velocity distributions are non-Gaussian. Equipartition of kinetic energy between translations and rotations is violated.

  1. Digital Library Storage using iRODS Data Grids

    NASA Astrophysics Data System (ADS)

    Hedges, Mark; Blanke, Tobias; Hasan, Adil

    Digital repository software provides a powerful and flexible infrastructure for managing and delivering complex digital resources and metadata. However, issues can arise in managing the very large, distributed data files that may constitute these resources. This paper describes an implementation approach that combines the Fedora digital repository software with a storage layer implemented as a data grid, using the iRODS middleware developed by DICE (Data Intensive Cyber Environments) as the successor to SRB. This approach allows us to use Fedoras flexible architecture to manage the structure of resources and to provide application- layer services to users. The grid-based storage layer provides efficient support for managing and processing the underlying distributed data objects, which may be very large (e.g. audio-visual material). The Rule Engine built into iRODS is used to integrate complex workflows at the data level that need not be visible to users, e.g. digital preservation functionality.

  2. The readout driver (ROD) for the ATLAS liquid argon calorimeters

    NASA Astrophysics Data System (ADS)

    Efthymiopoulos, Ilias

    2001-04-01

    The Readout Driver (ROD) for the Liquid Argon calorimeter of the ATLAS detector is described. Each ROD module receives triggered data from 256 calorimeter cells via two fiber-optics 1.28 Gbit/s links with a 100 kHz event rate (25 kbit/event). Its principal function is to determine the precise energy and timing of the signal from discrete samples of the waveform, taken each period of the LHC clock (25 ns). In addition, it checks, histograms, and formats the digital data stream. A demonstrator system, consisting of a motherboard and several daughter-board processing units (PUs) was constructed and is currently used for tests in the lab. The design of this prototype board is presented here. The board offers maximum modularity and allows the development and testing of different PU designs based on today's leading integer and floating point DSPs.

  3. Deposition of ZnO rods by electrochemically induced hydrolysis

    NASA Astrophysics Data System (ADS)

    Steegstra, Patrick; Ahlberg, Elisabet

    2014-01-01

    Galvanostatic electrodeposition of zinc oxide on gold electrodes was studied. Depositions were made from KCl solutions using oxygen reduction for driving the pH induced precipitation. The main focus was the influence of current density on the morphology and density of the deposit. The size, shape and density of the zinc oxide layer were shown to strongly depend on the current density. With an average rod diameter of 82 nm and a rod density of 36 μm-2 optimal conditions were found at -1.41 mA cm-2. The experimental results are discussed within the context of zinc oxide solubility and the near surface pH. For this purpose a simple model for surface pH is considered, based on concentration profiles of reaction products near an RDE and the speciation of zinc in aqueous solution.

  4. Overview of Fuel Rod Simulator Usage at ORNL

    NASA Astrophysics Data System (ADS)

    Ott, Larry J.; McCulloch, Reg

    2004-02-01

    During the 1970s and early 1980s, the Oak Ridge National Laboratory (ORNL) operated large out-of-reactor experimental facilities to resolve thermal-hydraulic safety issues in nuclear reactors. The fundamental research ranged from material mechanical behavior of fuel cladding during the depressurization phase of a loss-of-coolant accident (LOCA) to basic heat transfer research in gas- or sodium-cooled cores. The largest facility simulated the initial phase (less than 1 min. of transient time) of a LOCA in a commercial pressurized-water reactor. The nonnuclear reactor cores of these facilities were mimicked via advanced, highly instrumented electric fuel rod simulators locally manufactured at ORNL. This paper provides an overview of these experimental facilities with an emphasis on the fuel rod simulators.

  5. Do multilayer crystals nucleate in suspensions of colloidal rods?

    PubMed

    Patti, Alessandro; Dijkstra, Marjolein

    2009-03-27

    We study the isotropic-to-crystal transformation in a mixture of colloidal hard rods and nonabsorbing polymer using computer simulations. We determine the height of the nucleation barrier and find that the critical cluster consists of a single crystalline layer growing laterally for all polymer fugacities considered. At lower supersaturation, the free energy of a single hexagonally packed layer increases monotonically with size, while the nucleation barrier of a second crystalline layer is extremely high. Hence, the nucleation of multilayer crystals is never observed. Multilayer crystals form only in the spinodal decomposition regime, either where, in an intermediate stage, single crystalline membranes coalesce into multilayer clusters or where, at higher polymer fugacity, smaller clusters of rods stack on top of each other to form long filaments. Eventually, these transient structures evolve into a thermodynamically stable bulk crystal phase. PMID:19392328

  6. Novel venting technique for intramedullary rod fixation of pathologic fractures.

    PubMed

    Wilkens, Kenneth J; Nicolaou, Daemeon A M; Lee, Mark A

    2011-10-01

    This article introduces a novel technique to vent the femur and potentially decrease the embolic load created by reaming during intramedullary rod fixation of impending pathologic femur fractures. We used readily available operating room equipment to create a distal femoral vent hole without interfering with standard intramedullary instrumentation and with minimal increase in surgical time. This technique can be used for the prophylactic intramedullary stabilization of impending pathologic femur fractures from metabolic bone disease, metastatic cancer, and bisphosphonate use. PMID:21956178

  7. Rods-on-string idealization captures semiflexible filament dynamics

    NASA Astrophysics Data System (ADS)

    Chandran, Preethi L.; Mofrad, Mohammad R. K.

    2009-01-01

    We present an approach to modeling the two-dimensional Brownian dynamics of semiflexible filaments in the worm-model description as uniform, isotropic, and continuously flexible. Experimental observations increasingly show that the mechanical behavior of semiflexible filament networks departs from conventional knowledge. A force-balance-based dynamic simulation of the filament networks has multiple advantages as an approach to understanding their anomalous mechanics. However, a major disadvantage is the difficulty of capturing filament hydrodynamics and bending mechanics in a computationally efficient and physically consistent manner. To that end, we propose a strategy for modeling semiflexible filaments which involves idealizing a semiflexible filament as a contiguous string of flexible rods, and considering the Brownian forces on it as Einsteinian-like point normal and tangential forces. By idealizing the filament as a string of rods, we avoid the complex hydrodynamic treatment involved in beads-on-string idealizations, and implement large-deflection beam mechanics and filament inextensibility in a natural manner, while reducing the computational size of the problem. By considering the Brownian forces as point normal and tangential forces, we decompose the Brownian forces on straight and curved segments into a combination of classical resultant forces and couples whose distribution is shown to be governed by the rod diffusion coefficients. The decomposition allows solution of the Euler beam equations to second-order continuity between segments and fifth-order continuity within segments. We show that the approach is physically consistent by capturing multiple Brownian phenomena ranging from the rigid to the semiflexible limit: the translational and rotational diffusion of rigid rods; the thermal fluctuation of semirigid cantilever filaments; and the shape, bending, and time relaxation of freely diffusing, semiflexible actin filaments.

  8. NEURONATIN IS A STRESS-RESPONSIVE PROTEIN OF ROD PHOTORECEPTORS

    PubMed Central

    SHINDE, VISHAL; PITALE, PRIYAMVADA M.; HOWSE, WAYNE; GORBATYUK, OLEG; GORBATYUK, MARINA

    2016-01-01

    Neuronatin (NNAT) is a small transmembrane proteolipid that is highly expressed in the embryonic developing brain and several other peripheral tissues. This study is the first to provide evidence that NNAT is detected in the adult retina of various adult rod-dominant mammals, including wild-type (WT) rodents, transgenic rodents expressing mutant S334ter, P23H, or T17M rhodopsin, non-human primates, humans, and cone-dominant tree shrews. Immunohistochemical and quantitative real time polymerase chain reaction (qRT-PCR) analyses were applied to detect NNAT. Confocal microscopy analysis revealed that NNAT immunofluorescence is restricted to the outer segments (OSs) of photoreceptors without evidence of staining in other retinal cell types across all mammalian species. Moreover, in tree shrew retinas, we found NNAT to be co-localized with rhodopsin, indicating its predominant expression in rods. The rod-derived expression of NNAT was further confirmed by qRT-PCR in isolated rod photoreceptor cells. We also used these cells to mimic cellular stress in transgenic retinas by treating them with the endoplasmic reticulum stress inducer, tunicamycin. Thus, our data revealed accumulation of NNAT around the nucleus as compared to dispersed localization of NNAT within control cells. This distribution coincided with the partial intracellular mislocalization of NNAT to the outer nuclear layer observed in transgenic retinas. In addition, stressed retinas demonstrated an increase of NNAT mRNA and protein levels. Therefore, our study demonstrated that NNAT is a novel stress-responsive protein with a potential structural and/or functional role in adult mammalian retinas. PMID:27109921

  9. 10. View of Riverside Bridge with Steel Reinforcing Rods in ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    10. View of Riverside Bridge with Steel Reinforcing Rods in Place and with 'Tower for Concrete' in the Background. The function of the 'tower for concrete' is uncertain, but may have to do with the transport of concrete from the point of mixing to the point of use (suggestion by NDOT Bridge Section personnel, February 1990). Original snapshot taken July, 1920. - Riverside Bridge, Spanning Truckee River at Booth Street, Reno, Washoe County, NV

  10. VIEW OF CABLES AND TAPES ASSOCIATED WITH ADRIVE CONTROL ROD ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    VIEW OF CABLES AND TAPES ASSOCIATED WITH A-DRIVE CONTROL ROD SYSTEM, AT LEVEL +15’, DIRECTLY ABOVE PDP CONTROL ROOM, LOOKING NORTHWEST. THE CABLES FROM THE PDP ROOM GO THROUGH THE CONCRETE WALL, MAKE A RIGHT ANGLE TURN DOWNWARD, AND DESCEND INTO THE PDP CONTROL ROOM AS VERTICAL TAPES - Physics Assembly Laboratory, Area A/M, Savannah River Site, Aiken, Aiken County, SC

  11. K-band TWT using new diamond rod technology

    NASA Technical Reports Server (NTRS)

    Aldana, S. L.; Tamashiro, R. N.

    1990-01-01

    A 75-W CW helix TWT for satellite communications systems is being developed to operate at 20 GHz with an efficiency goal of 60 percent. A nonbrazed nonbonded diamond rod fabrication technique is used to develop the helix-type TWT. Techniques to enhance TWT efficiency are described, including the incorporation of a velocity tapered helix and a multistage graphite collector. Results from testing a breadboard TWT show a CW output power greater than 100 W and a 54.6 overall efficiency.

  12. Four-rod-λ/2-RFQ for light ion acceleration

    NASA Astrophysics Data System (ADS)

    Schempp, A.; Deitinghoff, H.; Ferch, M.; Junior, P.; Klein, H.

    1985-05-01

    A simple type of RFQ structure with circular rods as electrodes has been developed in Frankfurt. The improved design uses a linear arrangement of supporting stems on a massive common bar. This linear rf structure consists of a chain of λ/2-line pairs and leads to an advantageously simple but nonetheless effective RFQ structure. With this stable cheap type of RFQ resonator preaccelerator prototypes have been built for light ions. New results of electrode and structure optimization and beam measurements are presented.

  13. Neuronatin is a stress-responsive protein of rod photoreceptors.

    PubMed

    Shinde, Vishal; Pitale, Priyamvada M; Howse, Wayne; Gorbatyuk, Oleg; Gorbatyuk, Marina

    2016-07-22

    Neuronatin (NNAT) is a small transmembrane proteolipid that is highly expressed in the embryonic developing brain and several other peripheral tissues. This study is the first to provide evidence that NNAT is detected in the adult retina of various adult rod-dominant mammals, including wild-type (WT) rodents, transgenic rodents expressing mutant S334ter, P23H, or T17M rhodopsin, non-human primates, humans, and cone-dominant tree shrews. Immunohistochemical and quantitative real time polymerase chain reaction (qRT-PCR) analyses were applied to detect NNAT. Confocal microscopy analysis revealed that NNAT immunofluorescence is restricted to the outer segments (OSs) of photoreceptors without evidence of staining in other retinal cell types across all mammalian species. Moreover, in tree shrew retinas, we found NNAT to be co-localized with rhodopsin, indicating its predominant expression in rods. The rod-derived expression of NNAT was further confirmed by qRT-PCR in isolated rod photoreceptor cells. We also used these cells to mimic cellular stress in transgenic retinas by treating them with the endoplasmic reticulum stress inducer, tunicamycin. Thus, our data revealed accumulation of NNAT around the nucleus as compared to dispersed localization of NNAT within control cells. This distribution coincided with the partial intracellular mislocalization of NNAT to the outer nuclear layer observed in transgenic retinas. In addition, stressed retinas demonstrated an increase of NNAT mRNA and protein levels. Therefore, our study demonstrated that NNAT is a novel stress-responsive protein with a potential structural and/or functional role in adult mammalian retinas. PMID:27109921

  14. Rods-on-string idealization captures semiflexible filament dynamics.

    PubMed

    Chandran, Preethi L; Mofrad, Mohammad R K

    2009-01-01

    We present an approach to modeling the two-dimensional Brownian dynamics of semiflexible filaments in the worm-model description as uniform, isotropic, and continuously flexible. Experimental observations increasingly show that the mechanical behavior of semiflexible filament networks departs from conventional knowledge. A force-balance-based dynamic simulation of the filament networks has multiple advantages as an approach to understanding their anomalous mechanics. However, a major disadvantage is the difficulty of capturing filament hydrodynamics and bending mechanics in a computationally efficient and physically consistent manner. To that end, we propose a strategy for modeling semiflexible filaments which involves idealizing a semiflexible filament as a contiguous string of flexible rods, and considering the Brownian forces on it as Einsteinian-like point normal and tangential forces. By idealizing the filament as a string of rods, we avoid the complex hydrodynamic treatment involved in beads-on-string idealizations, and implement large-deflection beam mechanics and filament inextensibility in a natural manner, while reducing the computational size of the problem. By considering the Brownian forces as point normal and tangential forces, we decompose the Brownian forces on straight and curved segments into a combination of classical resultant forces and couples whose distribution is shown to be governed by the rod diffusion coefficients. The decomposition allows solution of the Euler beam equations to second-order continuity between segments and fifth-order continuity within segments. We show that the approach is physically consistent by capturing multiple Brownian phenomena ranging from the rigid to the semiflexible limit: the translational and rotational diffusion of rigid rods; the thermal fluctuation of semirigid cantilever filaments; and the shape, bending, and time relaxation of freely diffusing, semiflexible actin filaments. PMID:19257068

  15. Surface-induced nonlinearity enhancement in subwavelength rod waveguides

    SciTech Connect

    Marini, A.; Hartley, R.; Gorbach, A. V.; Skryabin, D. V.

    2011-12-15

    We develop a perturbative theory to describe optical propagation in subwavelength rod waveguides. In this approach, we account for loss and nonlinearity in the boundary conditions. A comparison to the traditional perturbative approach used in optical fibers reveals that the surface contribution provides a significant nonlinearity enhancement in the subwavelength regime. We further compare the nonlinearity enhancement of metallic, dielectric, and semiconductor waveguides, in addition to determining the attenuation coefficient of metallic nanowires.

  16. Comparison of hinged and contoured rods for occipitocervical arthrodesis in adults: A clinical study

    PubMed Central

    Abode-Iyamah, Kingsley O; Dlouhy, Brian J; Lopez, Alejandro J; Menezes, Arnold H; Hitchon, Patrick W; Dahdaleh, Nader S

    2016-01-01

    Introduction: A rigid construct that employs an occipital plate and upper cervical screws and rods is the current standard treatment for craniovertebral junction (CVJ) instability. A rod is contoured to accommodate the occipitocervical angle. Fatigue failure has been associated these acute bends. Hinged rod systems have been developed to obviate intraoperative rod contouring. Object: The aim of this study is to determine the safety and efficacy of the hinged rod system in occipitocervical fusion. Materials and Methods: This study retrospectively evaluated 39 patients who underwent occipitocervical arthrodesis. Twenty patients were treated with hinged rods versus 19 with contoured rods. Clinical and radiographic data were compared and analyzed. Results: Preoperative and postoperative Nurick and Frankel scores were similar between both groups. The use of allograft, autograft or bone morphogenetic protein was similar in both groups. The average number of levels fused was 4.1 (±2.4) and 3.4 (±2) for hinged and contoured rods, respectively. The operative time, estimated blood loss, and length of stay were similar between both groups. The occiput to C2 angle was similarly maintained in both groups and all patients demonstrated no movement across the CVJ on flexion-extension X-rays during their last follow-up. The average follow-up for the hinged and contoured rod groups was 12.2 months and 15.9 months, respectively. Conclusion: Hinged rods provide a safe and effective alternative to contoured rods during occipitocervical arthrodesis.

  17. Electrostatic Charging of Insulating Rods and Resulting Particle Transport in the Columbia Non-neutral Torus

    NASA Astrophysics Data System (ADS)

    Senter, Aaron; Rath, Nikolaus; Brenner, Paul; Sarasola, Xabier; Pedersen, Thomas

    2009-11-01

    The Columbia Non-neutral Torus (CNT) is a stellarator created to study non-neutral plasmas confined on magnetic surfaces. To create and diagnose the electron plasma, filaments supported by ceramic rods are inserted into the plasma. These rods charge negatively allowing particles to E xB drift across the confining magnetic surfaces and out of the plasma. A simple model of this process has yielded good qualitative agreement with experimentally observed radial transport[1]. However, when the rod is retracted, it perturbs the plasma more than expected. To better understand the rod perturbations, externally biased conducting rods are now being used. We find the effect of the ceramic rods by measuring the increase in filament emission current with a rod installed. Comparing the radial transport rates of the ceramic and conducting rods, we aim to understand the charge distribution on the former, and to minimize the rod driven transport. Initial experiments show that a uniformly biased rod does not reproduce the transport observed. Experiments using a rod with a varying radial potential profile are being conducted and will be reported on. [1] J.W. Berkery et al., Phys. Plasmas 14, 062503 (2007).

  18. Techniques and equipment for assessing the structural integrity of subterranean tower anchor rods

    DOEpatents

    Hinz, William R.; Parker, Matthew J.

    2001-01-01

    Techniques and equipment for evaluating structural integrity of buried anchor rods in situ are disclosed. The techniques avoid excavation of soil and avoid, or at least reduce, the possibility of damage to the rods or the concrete in which they may be embedded when evaluations are conducted. Instead, ultrasonic energy is transmitted through the rod from a portable transducer, and returned energy (in either or both of direct and mode-converted states) may be analyzed to assist in detecting flaws, corrosion, wastage, or other degradation of the rod. Data from a field evaluation may be compared with baseline data maintained either for a specific rod or for rods of similar composition and length (or both), and periodic field evaluations of a rod may be used to analyze trends in its structure over time.

  19. Tracer diffusion and cluster formation in mixtures of spheres and rotating rods

    NASA Astrophysics Data System (ADS)

    Kirchhoff, R.; Löwen, H.

    2005-12-01

    On the basis of Brownian dynamics computer simulation studies, we investigate the structure and dynamics of two-dimensional mixtures of rods driven by an external torque and spheres. First, we show that the tracer long-time diffusion of spheres in a system of rotating rods can be efficiently tuned via the rod density. It behaves non-monotonically for increasing rod density. In particular, the sphere diffusion becomes strongly enhanced across the jamming transition of the rods. Second, we show that rotating rods in a dense suspension of spheres form aggregates of rod clusters which are rotating jointly. The cluster size is in reasonable agreement with the predictions of a simple theory.

  20. Clustering-Induced Attraction in Granular Mixtures of Rods and Spheres

    PubMed Central

    2016-01-01

    Depletion-induced aggregation of rods enhanced by clustering is observed to produce a novel model of attractive pairs of rods separated by a line of spheres in a quasi-2D, vertically-shaken, granular gas of rods and spheres. We show that the stability of these peculiar granular aggregates increases as a function of shaking intensity. Velocity distributions of spheres inside and outside of a pair of rods trapping a line of spheres show a clear suppression of the momentum acquired by the trapped spheres. The condensed phase formed between the rods is caused by a clustering instability of the trapped spheres, enhanced by a vertical guidance produced by the confining rods. The liberated area corresponding to direct excluded-volume pairs and indirect depletion-aggregated pairs is measured as a function of time. The stability of rod pairs mediated by spheres reveals an attraction comparable in strength to the one purely induced by depletion forces. PMID:27218804

  1. Cladding corrosion and hydriding in irradiated defected zircaloy fuel rods (LWBR Development Program)

    SciTech Connect

    Clayton, J.C.

    1985-08-01

    Twenty-one LWBR irradiation test rods containing ThO/sub 2/-UO/sub 2/ fuel and Zircaloy cladding with holes or cracks operated successfully. Zircaloy cladding corrosion on the inside and outside diameter surfaces and hydrogen pickup in the cladding were measured. The observed outer surface Zircaloy cladding corrosion oxide thicknesses of the test rods were similar to thicknesses measured for nondefected irradiation test rods. An analysis model, which was developed to calculate outer surface oxide thickness of non-defected rods, gave results which were in reasonable agreement with the outer surface oxide thicknesses of defected rods. When the analysis procedure was modified to account for additional corrosion proportional to fission rate and to time, the calculated values agreed well with measured inner oxide corrosion film values. Hydrogen pickup in the defected rods was not directly proportional to local corrosion oxide weight gain as was the case for non-defected rods. 16 refs., 6 figs., 8 tabs.

  2. Rod transduction parameters from the a wave of local receptor populations

    NASA Astrophysics Data System (ADS)

    Nusinowitz, Steven; Hood, Donald C.; Birch, David G.

    1995-10-01

    The analysis of electroretinogram a waves from locally stimulated populations of rods is complicated by the presence of scattered light within the eye. Scattered-light and cone contributions can be assessed after brief flashes of light designed to saturate only rods in the locally stimulated area. Subtracting the scattered-light and the cone responses from the local electroretinogram gives a pure rod a wave that can be fitted with models of photoreceptor activity. We demonstrate the feasibility of this technique by recording local rod a waves from a group of five normal subjects and by fitting the a waves with the rod model to derive transduction parameters. The local rod a waves are compared with expected responses derived from simulations in which the response of the entire retina to heterogeneous illumination is mimicked. electroretinography, rods, scattered light.

  3. Preliminary design report for the prototypical fuel rod consolidation system

    SciTech Connect

    Rosa, J.M.

    1986-12-03

    This report documents NUTECH's preliminary design of a dry, spent fuel rod consolidation system. This preliminary design is the result of Phase I of a planned four phase project. The present report on this project provides a considerable amount of detail for a preliminary design effort. The design and all of its details are described in this Preliminary Design Report (PDR). The NUTECH dry rod consolidation system described herein is remotely operated. It provides for automatic operation, but with operator hold points between key steps in the process. The operator has the ability to switch to a manual operation mode at any point in the process. The system is directed by the operator using an executive computer which controls and coordinates the operation of the in-cell equipment. The operator monitors the process using an in-cell closed circuit television (CCTV) system with audio output and equipment status displays on the computer monitor. The in-cell mechanical equipment consists of the following: (1) two overhead cranes with manipulators; (2) a multi-degree of freedom fuel handling table and its clamping equipment; (3) a fuel assembly end fitting removal station and its tools; (4) a consolidator (which pulls rods, assembles the consolidated bundle and loads the canister); (5) a canister end cap welder and weld inspection system; (6) decontamination systems; and (7) the CCTV and microphone systems.

  4. Internal Control Rod Drive Mechanisms, Design Options for IRIS

    SciTech Connect

    Conway, Lawrence E.; Petrovic, Bojan

    2004-07-01

    IRIS (International Reactor Innovative and Secure) is a medium-power (335 MWe) PWR with an integral, primary circuit configuration, where all the reactor coolant system components are contained within the reactor vessel. This integral configuration is a key reason for the success of IRIS' 'safety-by-design' approach, whereby accident initiators are eliminated or the accident consequences and/or frequency are reduced. The most obvious example of the IRIS safety by design approach is the elimination of large LOCA's, since the integral reactor coolant system has no large loop piping. Another serious accident scenario that is being addressed in IRIS is the postulated ejection of a reactor control cluster assembly (RCCA). This accident initiator can be eliminated by locating the RCCA drive mechanisms (CRDMs) inside the reactor vessel. This eliminates the mechanical drive rod penetration between the RCCA and the external CRDM, eliminating the potential for differential pressure across the pressure boundary, and thus eliminating 'by design' the possibility for rod ejection accident. Moreover, the elimination of the 'large' drive-rod penetrations and the external CRDM pressure housings decreases the likelihood of boric acid leakage and subsequent corrosion of the reactor pressure boundary (like the Davis-Besse incident). This paper will discuss the IRIS top level design requirements and objectives for internal CRDMs, and provide examples candidate designs and their specific performance characteristics. (authors)

  5. Spare the rods and spoil the retina: revisited.

    PubMed

    Sivaprasad, S; Arden, G

    2016-02-01

    Visual function improves with oxygen inhalation in people with diabetes even in the absence of visible retinopathy. Rods consume the most oxygen in the retina due to the high metabolic activity required to maintain the dark current. Therefore, Arden hypothesized that in diabetes where oxygen supply may also be affected due to the changes in retinal vasculature, prevention of dark adaptation may be a viable option to prevent or decrease the rate of progression of diabetic retinopathy. Animal experiments have proven that the absence of rods decreases the development of retinal neovascularisation. The same principle applies to panretinal photocoagulation, an established treatment for proliferative diabetic retinopathy. Recently, a few clinical studies have also shown that preventing dark adaptation by suppressing rods with 500-nm light source at night decreases the rate of progression of early diabetic retinopathy and maculopathy in the short-term. We await the results of a large two-year multi-centre trial (CLEOPATRA trial) to evaluate the long-term effects of decreasing dark adaptation by applying a 500nm light source as a mask over eyes with non-central diabetic macular oedema. PMID:26656085

  6. Model of ASTM Flammability Test in Microgravity: Iron Rods

    NASA Technical Reports Server (NTRS)

    Steinberg, Theodore A; Stoltzfus, Joel M.; Fries, Joseph (Technical Monitor)

    2000-01-01

    There is extensive qualitative results from burning metallic materials in a NASA/ASTM flammability test system in normal gravity. However, this data was shown to be inconclusive for applications involving oxygen-enriched atmospheres under microgravity conditions by conducting tests using the 2.2-second Lewis Research Center (LeRC) Drop Tower. Data from neither type of test has been reduced to fundamental kinetic and dynamic systems parameters. This paper reports the initial model analysis for burning iron rods under microgravity conditions using data obtained at the LERC tower and modeling the burning system after ignition. Under the conditions of the test the burning mass regresses up the rod to be detached upon deceleration at the end of the drop. The model describes the burning system as a semi-batch, well-mixed reactor with product accumulation only. This model is consistent with the 2.0-second duration of the test. Transient temperature and pressure measurements are made on the chamber volume. The rod solid-liquid interface melting rate is obtained from film records. The model consists of a set of 17 non-linear, first-order differential equations which are solved using MATLAB. This analysis confirms that a first-order rate, in oxygen concentration, is consistent for the iron-oxygen kinetic reaction. An apparent activation energy of 246.8 kJ/mol is consistent for this model.

  7. One-dimensional nanoferroic rods; synthesis and characterization

    NASA Astrophysics Data System (ADS)

    Ahmed, M. A.; Seddik, U.; Okasha, N.; Imam, N. G.

    2015-11-01

    One-dimensional nanoferroic rods of BaTiO3 were synthesized by improved citrate auto-combustion technology using tetrabutyl titanate. X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX), transmission electron microscopy (TEM), atomic force microscopy (AFM) and Fourier transform infrared spectroscopy (FTIR) have been used to characterize the prepared sample. The results indicated that the crystal structure of BaTiO3 is tetragonal phase with an average crystallite size of 47 nm. SEM image gives a cauliflower-like morphology of the agglomerated nanorods. The stoichiometry of the chemical composition of the BaTiO3 ceramic was confirmed by EDX. TEM micrograph exhibited that BaTiO3 nanoparticles have rod-like shape with an average length of 120 nm and width of 43 nm. AFM was used to investigate the surface topography and its roughness. The topography image in 3D showed that the BaTiO3 particles have a rod shape with an average particle size of 116 nm which in agreement with 3D TEM result.

  8. Hybrid nuclear reactor grey rod to obtain required reactivity worth

    DOEpatents

    Miller, John V.; Carlson, William R.; Yarbrough, Michael B.

    1991-01-01

    Hybrid nuclear reactor grey rods are described, wherein geometric combinations of relatively weak neutron absorber materials such as stainless steel, zirconium or INCONEL, and relatively strong neutron absorber materials, such as hafnium, silver-indium cadmium and boron carbide, are used to obtain the reactivity worths required to reach zero boron change load follow. One embodiment includes a grey rod which has combinations of weak and strong neutron absorber pellets in a stainless steel cladding. The respective pellets can be of differing heights. A second embodiment includes a grey rod with a relatively thick stainless steel cladding receiving relatively strong neutron absorber pellets only. A third embodiment includes annular relatively weak netron absorber pellets with a smaller diameter pellet of relatively strong absorber material contained within the aperture of each relatively weak absorber pellet. The fourth embodiment includes pellets made of a homogeneous alloy of hafnium and a relatively weak absorber material, with the percentage of hafnium chosen to obtain the desired reactivity worth.

  9. Tubing rotator reduces tubing wear in rod pumped wells

    SciTech Connect

    Graham, M. ); Brown, C. )

    1994-04-04

    Tubing failures are both expensive and time-consuming. The most common failure results from rod cutting, or, erosion of the tubing ID because of continuous, reciprocating contact with the rod string. Installation of tubing rotators has decreased tubing failures in West Texas waterflood sucker-rod pumped wells. Pumping unit movement powers the rotator system, turning the tubing string at about 1 revolution/day. The rotator system has both surface and subsurface components. A reduction gear box attached to the walking beam converts the pumping unit's reciprocating strokes into rotary motion. A drive line transfers this rotary motion to a gear-driven suspension mandrel in the rotating tubing hanger. Near the bottom of the tubing string, a rotating tubing anchor/catcher allows the entire tubing string, including the tail pipe, seating nipple, and gas and mud anchor to rotate. The rotator hanger suspends the weight of the tubing string on a bearing system. One model of the hanger has a load capacity of 135,000 lb. A surface swivel allows rotation below the pumping tee so that the flow lines remain stationary. Also included in the string is a safety shear coupling to prevent over torquing the tubing.

  10. Gelation of rod particle suspension in Newtonian fluid

    NASA Astrophysics Data System (ADS)

    Han, Hyejin; Kim, Chongyoup

    2015-05-01

    The gelation of FeOOH rod particles in a glycerin-water mixture under shear flows is investigated using rheological measurements. The average length and the average diameter of the rod particles are 1 μm and 120 nm, respectively. The van der Waals energy is much larger than the Brownian and electrostatic contributions. To examine the effect of shear history on gelation, two different kinds of experimental procedures are used: A strong, but short preshear followed by a creep test and a preshear for a long time followed by a creep test. The rod particle suspension becomes a gel during the creep test showing the plateau in G' and yield stress. The gelation time during the creep test is dependent on preshear time while it is not affected by the preshear stress for a short time before the creep test. Both the plateau in G' and the yield stress are larger when the preshear time is longer. The gelation appears to occur by two steps of the formation of flocs by the aggregation of individual particles and then the formation of the sample spanning network by the aggregation of the flocs. Gel strength appears to be dependent on floc size which is determined by the imposed shear stress in the present case of shear induced gelation.

  11. Spatiotemporal cGMP Dynamics in Living Mouse Rods

    PubMed Central

    Gross, Owen P.; Pugh, Edward N.; Burns, Marie E.

    2012-01-01

    Signaling of single photons in rod photoreceptors decreases the concentration of the second messenger, cyclic GMP (cGMP), causing closure of cGMP-sensitive channels located in the plasma membrane. Whether the spatiotemporal profiles of the fall in cGMP are narrow and deep, or broad and shallow, has important consequences for the amplification and the fidelity of signaling. The factors that determine the cGMP profiles include the diffusion coefficient for cGMP, the spontaneous rate of cGMP hydrolysis, and the rate of cGMP synthesis, which is powerfully regulated by calcium feedback mechanisms. Here, using suction electrodes to record light-dependent changes in cGMP-activated current in living mouse rods lacking calcium feedback, we have determined the rate constant of spontaneous cGMP hydrolysis and the longitudinal cGMP diffusion coefficient. These measurements result in a fully constrained spatiotemporal model of phototransduction, which we used to determine the effect of feedback to cGMP synthesis in spatially constricting the fall of cGMP during the single-photon response of normal rods. We find that the spatiotemporal cGMP profiles during the single-photon response are optimized for maximal amplification and preservation of signal linearity, effectively operating within an axial signaling domain of ∼2 μm. PMID:22768933

  12. Square Grains in Asymmetric Rod-Coil Block Copolymers

    SciTech Connect

    Olsen, B.D.; Toney, M.F.; Segalman, R.A.; /UC, Berkeley /LBL, Berkeley /SLAC, SSRL

    2009-04-30

    Unlike the rounded grains that are well known to form in most soft materials, square grains of microphase-separated lamellae are observed in thin films of a rod-coil block copolymer because of hierarchical structuring originating from the molecular packing of the rods. The square grains are oriented with lamellar layers parallel to the film interface and result from growth along orthogonal low-surface-energy directions as a result of the effects of the tetragonal crystalline lattice that forms within the rod-rich lamellar nanodomains of poly(2,5-di(2{prime}-ethylhexyloxy)-1,4-phenylene vinylene)-b-polyisoprene (PPV-b-PI). These grain shapes form only for a narrow range of coil volume fractions around 72% as a result of kinetic barriers at lower coil fractions and disordering of the lattice at higher coil fractions, and the polydisperse grain size suggests that growth is nucleation-limited. The grains form in both weakly and moderately segregated polymers at all annealing temperatures below the order-disorder transition, and they are observed for all thicknesses at which parallel-oriented grains are grown.

  13. Design and diagnosis of deviated rod-pumped wells

    SciTech Connect

    Gibbs, S.G. )

    1992-07-01

    Commonly used methods for designing rod-pumping installations presume vertical wells. This paper introduces a wave equation methodology that applies to deviated wells, whether they are deviated intentionally or unintentionally. Restrictions on surface locations and interest in horizontal drilling are increasing the need for deviated wells. Together with long-standing crooked-hole problems, these are promising subjects for further study. This paper describes a predictive method that applies to 3D problems. A well deemed too crooked to pump is studies, and a procedure for designing intentionally deviated wells is presented. The relative friction effects of rod guides are discussed, and the effect of borehole path on power consumption is treated. Deviated wells can be adequately designed with wave equation methods, and highly deviated wells can be produced with rod-pumping equipment when care is taken to control the path of the borehole. This paper should be considered as a progress report because much remains to be learned about the application of this petroleum technology.

  14. Activation and deactivation of vibronic channels in intact phycocyanin rods

    NASA Astrophysics Data System (ADS)

    Nganou, C.; David, L.; Meinke, R.; Adir, N.; Maultzsch, J.; Mkandawire, M.; Pouhè, D.; Thomsen, C.

    2014-02-01

    We investigated the excitation modes of the light-harvesting protein phycocyanin (PC) from Thermosynechococcus vulcanus in the crystalline state using UV and near-infrared Raman spectroscopy. The spectra revealed the absence of a hydrogen out-of-plane wagging (HOOP) mode in the PC trimer, which suggests that the HOOP mode is activated in the intact PC rod, while it is not active in the PC trimer. Furthermore, in the PC trimer an intense mode at 984 cm-1 is assigned to the C-C stretching vibration while the mode at 454 cm-1 is likely due to ethyl group torsion. In contrast, in the similar chromophore phytochromobilin the C5,10,15-D wag mode at 622 cm-1 does not come from a downshift of the HOOP. Additionally, the absence of modes between 1200 and 1300 cm-1 rules out functional monomerization. A correlation between phycocyanobilin (PCB) and phycoerythrobilin (PEB) suggests that the PCB cofactors of the PC trimer appear in a conformation similar to that of PEB. The conformation of the PC rod is consistent with that of the allophycocyanin (APC) trimer, and thus excitonic flow is facilitated between these two independent light-harvesting compounds. This excitonic flow from the PC rod to APC appears to be modulated by the vibration channels during HOOP wagging, C = C stretching, and the N-H rocking in-plan vibration.

  15. 76 FR 24018 - Notice of Availability of the Draft Supplemental Environmental Impact Statement for the Nuclear...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-29

    ... the CMRR Project in February 2004 (68 FR 6420) announcing its decision to construct and operate a two... and selected in the 2004 ROD (69 FR 6967) and the 2008 Complex Transformation SPEIS ROD (73 FR 77656... Impact Statement for the Nuclear Facility Portion of the Chemistry and Metallurgy Research...

  16. Toward a unified model of vertebrate rod phototransduction

    PubMed Central

    HAMER, R.D.; NICHOLAS, S.C.; TRANCHINA, D.; LAMB, T.D.; JARVINEN, J.L.P.

    2006-01-01

    Recently, we introduced a phototransduction model that was able to account for the reproducibility of vertebrate rod single-photon responses (SPRs) (Hamer et al., 2003). The model was able to reproduce SPR statistics by means of stochastic activation and inactivation of rhodopsin (R*), transducin (Gα), and phosphodiesterase (PDE). The features needed to capture the SPR statistics were (1) multiple steps of R* inactivation by means of multiple phosphorylations (followed by arrestin capping) and (2) phosphorylation dependence of the affinity between R* and the three molecules competing to bind with R* (Gα, arrestin, and rhodopsin kinase). The model was also able to account for several other rod response features in the dim-flash regime, including SPRs obtained from rods in which various elements of the cascade have been genetically disabled or disrupted. However, the model was not tested under high light-level conditions. We sought to evaluate the extent to which the multiple phosphorylation model could simultaneously account for single-photon response behavior, as well as responses to high light levels causing complete response saturation and/or significant light adaptation (LA). To date no single model, with one set of parameters, has been able to do this. Dim-flash responses and statistics were simulated using a hybrid stochastic/deterministic model and Monte-Carlo methods as in Hamer et al. (2003). A dark-adapted flash series, and stimulus paradigms from the literature eliciting various degrees of light adaptation (LA), were simulated using a full differential equation version of the model that included the addition of Ca2+-feedback onto rhodopsin kinase via recoverin. With this model, using a single set of parameters, we attempted to account for (1) SPR waveforms and statistics (as in Hamer et al., 2003); (2) a full dark-adapted flash-response series, from dim flash to saturating, bright flash levels, from a toad rod; (3) steady-state LA responses, including

  17. Rhodopsin Gene Expression Determines Rod Outer Segment Size and Rod Cell Resistance to a Dominant-Negative Neurodegeneration Mutant

    PubMed Central

    Price, Brandee A.; Sandoval, Ivette M.; Chan, Fung; Nichols, Ralph; Roman-Sanchez, Ramon; Wensel, Theodore G.; Wilson, John H.

    2012-01-01

    Two outstanding unknowns in the biology of photoreceptors are the molecular determinants of cell size, which is remarkably uniform among mammalian species, and the mechanisms of rod cell death associated with inherited neurodegenerative blinding diseases such as retinitis pigmentosa. We have addressed both questions by performing an in vivo titration with rhodopsin gene copies in genetically engineered mice that express only normal rhodopsin or an autosomal dominant allele, encoding rhodopsin with a disease-causing P23H substitution. The results reveal that the volume of the rod outer segment is proportional to rhodopsin gene expression; that P23H-rhodopsin, the most common rhodopsin gene disease allele, causes cell death via a dominant-negative mechanism; and that long term survival of rod cells carrying P23H-rhodopsin can be achieved by increasing the levels of wild type rhodopsin. These results point to promising directions in gene therapy for autosomal dominant neurodegenerative diseases caused by dominant-negative mutations. PMID:23185477

  18. Multiple rod-cone and cone-rod photoreceptor transmutations in snakes: evidence from visual opsin gene expression.

    PubMed

    Simões, Bruno F; Sampaio, Filipa L; Loew, Ellis R; Sanders, Kate L; Fisher, Robert N; Hart, Nathan S; Hunt, David M; Partridge, Julian C; Gower, David J

    2016-01-27

    In 1934, Gordon Walls forwarded his radical theory of retinal photoreceptor 'transmutation'. This proposed that rods and cones used for scotopic and photopic vision, respectively, were not fixed but could evolve into each other via a series of morphologically distinguishable intermediates. Walls' prime evidence came from series of diurnal and nocturnal geckos and snakes that appeared to have pure-cone or pure-rod retinas (in forms that Walls believed evolved from ancestors with the reverse complement) or which possessed intermediate photoreceptor cells. Walls was limited in testing his theory because the precise identity of visual pigments present in photoreceptors was then unknown. Subsequent molecular research has hitherto neglected this topic but presents new opportunities. We identify three visual opsin genes, rh1, sws1 and lws, in retinal mRNA of an ecologically and taxonomically diverse sample of snakes central to Walls' theory. We conclude that photoreceptors with superficially rod- or cone-like morphology are not limited to containing scotopic or photopic opsins, respectively. Walls' theory is essentially correct, and more research is needed to identify the patterns, processes and functional implications of transmutation. Future research will help to clarify the fundamental properties and physiology of photoreceptors adapted to function in different light levels. PMID:26817768

  19. Nonlinear dynamics of a rotating elastic rod in a viscous fluid.

    PubMed

    Lee, Wanho; Kim, Yongsam; Olson, Sarah D; Lim, Sookkyung

    2014-09-01

    The dynamics of an elastic rod in a viscous fluid at zero Reynolds number is investigated when the bottom end of the rod is tethered at a point in space and rotates at a prescribed angular frequency, while the other part of the rod freely moves through the fluid. A rotating elastic rod, which is intrinsically straight, exhibits three dynamical motions: twirling, overwhirling, and whirling. The first two motions are stable, whereas the last motion is unstable. The stability of dynamical motions is determined by material and geometrical properties of the rod, fluid properties, and the angular frequency of the rod. We employ the regularized Stokes flow to describe the fluid motion and the Kirchhoff rod model to describe the elastic rod. Our simulation results display subcritical Hopf bifurcation diagrams indicating the bistability region. We also investigate the whirling motion generated by the rotation of an intrinsically bent rod. It is observed that the angular frequency determines the handedness of the whirling rod and thus the flow direction and that there is a critical frequency which separates the positive (upward) flow at frequencies above it from the negative (downward) flow at frequencies below it. PMID:25314534

  20. Structural Integrity Testing Method for PRSEUS Rod-Wrap Stringer Design

    NASA Technical Reports Server (NTRS)

    Wang, John T.; Grenoble, Ray W.; Pickell, Robert D.

    2012-01-01

    NASA Langley Research Center and The Boeing Company are developing an innovative composite structural concept, called PRSEUS, for the flat center section of a future environmentally friendly hybrid wing body (HWB) aircraft. The PRSEUS (Pultruded Rod Stitched Efficient Unitized Structure) concept uses dry textile preforms for the skins, frames, and stiffener webs. The highly loaded stiffeners are made from precured unidirectional carbon/epoxy rods and dry fiber preforms. The rods are wrapped with the dry fiber preforms and a resin infusion process is used to form the rod-wrap stiffeners. The structural integrity of the rod-wrap interface is critical for maintaining the panel s high strength and bending rigidity. No standard testing method exists for testing the strength of the rod-wrap bondline. Recently, Boeing proposed a rod push-out testing method and conducted some preliminary tests using this method. This paper details an analytical study of the rod-wrap bondline. The rod-wrap interface is modeled as a cohesive zone for studying the initiation and growth of interfacial debonding during push-out testing. Based on the correlations of analysis results and Boeing s test data, the adequacy of the rod-wrap testing method is evaluated, and potential approaches for improvement of the test method are proposed.

  1. General investigation of elastic thin rods as subject to a terminal twist

    NASA Astrophysics Data System (ADS)

    Hu, Kai

    2007-09-01

    The recent development of DNA structure, brought by the elastic rod model, revives the study of the so-called Michell-Zajac instability for isotropic naturally straight elastic rings. The instability states that when subjected to a terminal twist, a manipulation which cuts, rotates, and then seals closed rods, an elastic ring does not writhe until the amount of rotation exceeds a rod-dependent threshold. From the data generated by a finite element method, Bauer, Lund, and White [Proc. Natl. Acad. Sci. USA. 90, 833 (1993)] concluded that the instability becomes extreme for isotropic naturally singly bent, doubly bent, and O -ring elastic rings since they writhe immediately as subject to a terminal twist. This paper continues their study for other closed rods. In order to understand DNA structure in DNA-protein interactions, this paper also extends the study to open rods with clamped ends; for such rods, a terminal twist is a manipulation which releases, rotates, and then reclamps one end of the rods. Moreover, the rods under consideration need not be isotropic or may violate Kirchhoff-Clebsch conservation law of total energy. By linearizing the Euler-Lagrange equations which govern equilibrium rods and analyzing the linearized equations, this paper establishes an inequality such that if the initial values of the bending curvatures, their first derivatives, and the twisting density of an equilibrium rod satisfy the inequality, the rod axis deforms immediately as the rod is subject to a terminal twist. Since the initial data dissatisfying the inequality form a hypersurface in the five-dimensional Euclidean space, this paper asserts that a terminal twist makes the axis deformed instantly for almost every equilibrium rod.

  2. General investigation of elastic thin rods as subject to a terminal twist.

    PubMed

    Hu, Kai

    2007-09-01

    The recent development of DNA structure, brought by the elastic rod model, revives the study of the so-called Michell-Zajac instability for isotropic naturally straight elastic rings. The instability states that when subjected to a terminal twist, a manipulation which cuts, rotates, and then seals closed rods, an elastic ring does not writhe until the amount of rotation exceeds a rod-dependent threshold. From the data generated by a finite element method, Bauer, Lund, and White [Proc. Natl. Acad. Sci. USA. 90, 833 (1993)] concluded that the instability becomes extreme for isotropic naturally singly bent, doubly bent, and O -ring elastic rings since they writhe immediately as subject to a terminal twist. This paper continues their study for other closed rods. In order to understand DNA structure in DNA-protein interactions, this paper also extends the study to open rods with clamped ends; for such rods, a terminal twist is a manipulation which releases, rotates, and then reclamps one end of the rods. Moreover, the rods under consideration need not be isotropic or may violate Kirchhoff-Clebsch conservation law of total energy. By linearizing the Euler-Lagrange equations which govern equilibrium rods and analyzing the linearized equations, this paper establishes an inequality such that if the initial values of the bending curvatures, their first derivatives, and the twisting density of an equilibrium rod satisfy the inequality, the rod axis deforms immediately as the rod is subject to a terminal twist. Since the initial data dissatisfying the inequality form a hypersurface in the five-dimensional Euclidean space, this paper asserts that a terminal twist makes the axis deformed instantly for almost every equilibrium rod. PMID:17930274

  3. Rod consolidation of RG and E's (Rochester Gas and Electric Corporation) spent PWR (pressurized water reactor) fuel

    SciTech Connect

    Bailey, W.J.

    1987-05-01

    The rod consolidation demonstration involved pulling the fuel rods from five fuel assemblies from Unit 1 of RG and E's R.E. Ginna Nuclear Power Plant. Slow and careful rod pulling efforts were used for the first and second fuel assemblies. Rod pulling then proceeded smoothly and rapidly after some minor modifications were made to the UST and D consolidation equipment. The compaction ratios attained ranged from 1.85 to 2.00 (rods with collapsed cladding were replaced by dummy rods in one fuel assembly to demonstrate the 2:1 compaction ratio capability). This demonstration involved 895 PWR fuel rods, among which there were some known defective rods (over 50 had collapsed cladding); no rods were broken or dropped during the demonstration. However, one of the rods with collapsed cladding unexplainably broke during handling operations (i.e., reconfiguration in the failed fuel canister), subsequent to the rod consolidation demonstration. The broken rod created no facility problems; the pieces were encapsulated for subsequent storage. Another broken rod was found during postdemonstration cutting operations on the nonfuel-bearing structural components from the five assemblies; evidence indicates it was broken prior to any rod consolidation operations. During the demonstration, burnish-type lines or scratches were visible on the rods that were pulled; however, experience indicates that such lines are generally produced when rods are pulled (or pushed) through the spacer grids. Rods with collapsed cladding would not enter the funnel (the transition device between the fuel assembly and the canister that aids in obtaining high compaction ratios). Reforming of the flattened areas of the cladding on those rods was attempted to make the rod cross sections more nearly circular; some of the reformed rods passed through the funnel and into the canister.

  4. Morphological Diversity of the Rod Spherule: A Study of Serially Reconstructed Electron Micrographs

    PubMed Central

    Li, Shuai; Mitchell, Joe; Briggs, Deidrie J.; Young, Jaime K.; Long, Samuel S.; Fuerst, Peter G.

    2016-01-01

    Purpose Rod spherules are the site of the first synaptic contact in the retina’s rod pathway, linking rods to horizontal and bipolar cells. Rod spherules have been described and characterized through electron micrograph (EM) and other studies, but their morphological diversity related to retinal circuitry and their intracellular structures have not been quantified. Most rod spherules are connected to their soma by an axon, but spherules of rods on the surface of the Mus musculus outer plexiform layer often lack an axon and have a spherule structure that is morphologically distinct from rod spherules connected to their soma by an axon. Retraction of the rod axon and spherule is often observed in disease processes and aging, and the retracted rod spherule superficially resembles rod spherules lacking an axon. We hypothesized that retracted spherules take on an axonless spherule morphology, which may be easier to maintain in a diseased state. To test our hypothesis, we quantified the spatial organization and subcellular structures of rod spherules with and without axons. We then compared them to the retracted spherules in a disease model, mice that overexpress Dscam (Down syndrome cell adhesion molecule), to gain a better understanding of the rod synapse in health and disease. Methods We reconstructed serial EM images of wild type and DscamGoF (gain of function) rod spherules at a resolution of 7 nm in the X-Y axis and 60 nm in the Z axis. Rod spherules with and without axons, and retracted spherules in the DscamGoF retina, were reconstructed. The rod spherule intracellular organelles, the invaginating dendrites of rod bipolar cells and horizontal cell axon tips were also reconstructed for statistical analysis. Results Stereotypical rod (R1) spherules occupy the outer two-thirds of the outer plexiform layer (OPL), where they present as spherical terminals with large mitochondria. This spherule group is highly uniform and composed more than 90% of the rod spherule

  5. Phase behavior of mixtures of colloidal rods and spheres

    NASA Astrophysics Data System (ADS)

    Adams, Marie Elizabeth

    In this thesis we study entropy driven order in mixtures of rods and spheres. Systems of rod-like particles, as pure systems, exhibit rich liquid crystalline phase behavior. We chose to work with aqueous suspensions of either TMV or fd virus particles, both rod-like lyotropic systems. We complicate the phase behavior by adding a second component, colloidal spheres (PEG/PEO, BSA, polystyrene latex, or Dextran). Our first paper explores the phase behavior of TMV mixed with BSA or PEO, mapping out a phase diagram based on optical microscopy observations. We found our qualitative observations of TMV mixtures to be consistent with theoretical models of the depletion force. The second paper extends our study of phase behavior to mixtures of fd virus and polystyrene latex spheres. We qualitatively observe bulk demixing for very small diameter added spheres and for very large diameter added spheres. In addition, we observed microphase separation morphologies, such as lamellar and columnar structures, which formed for fd mixed with polystyrene latex spheres 0.1 microns in diameter. All of these microphase samples were viewed with differential interference microscopy (a few samples were further investigated using electron microscopy). Both our data and theoretical calculations illustrated that 0.1 micron diameter spheres have a stabilizing effect on the smectic phase. Our final work focused on fd virus mixed with Dextran. The purpose of these experiments was to examine the effect of added polymer on the isotropic-cholesteric co-existence region. I-Ch samples were prepared and fd and Dextran concentrations were measured using a spectrophotometer. Several conditions were explored, including two different molecular weights of Dextran and a range of ionic strengths. In agreement with theoretical predictions, the I-Ch coexistence region widens with added Dextran with the polymer preferentially partioned into the isotropic phase.

  6. Rod Monochromacy and the Coevolution of Cetacean Retinal Opsins

    PubMed Central

    Meredith, Robert W.; Gatesy, John; Emerling, Christopher A.; York, Vincent M.; Springer, Mark S.

    2013-01-01

    Cetaceans have a long history of commitment to a fully aquatic lifestyle that extends back to the Eocene. Extant species have evolved a spectacular array of adaptations in conjunction with their deployment into a diverse array of aquatic habitats. Sensory systems are among those that have experienced radical transformations in the evolutionary history of this clade. In the case of vision, previous studies have demonstrated important changes in the genes encoding rod opsin (RH1), short-wavelength sensitive opsin 1 (SWS1), and long-wavelength sensitive opsin (LWS) in selected cetaceans, but have not examined the full complement of opsin genes across the complete range of cetacean families. Here, we report protein-coding sequences for RH1 and both color opsin genes (SWS1, LWS) from representatives of all extant cetacean families. We examine competing hypotheses pertaining to the timing of blue shifts in RH1 relative to SWS1 inactivation in the early history of Cetacea, and we test the hypothesis that some cetaceans are rod monochomats. Molecular evolutionary analyses contradict the “coastal” hypothesis, wherein SWS1 was pseudogenized in the common ancestor of Cetacea, and instead suggest that RH1 was blue-shifted in the common ancestor of Cetacea before SWS1 was independently knocked out in baleen whales (Mysticeti) and in toothed whales (Odontoceti). Further, molecular evidence implies that LWS was inactivated convergently on at least five occasions in Cetacea: (1) Balaenidae (bowhead and right whales), (2) Balaenopteroidea (rorquals plus gray whale), (3) Mesoplodon bidens (Sowerby's beaked whale), (4) Physeter macrocephalus (giant sperm whale), and (5) Kogia breviceps (pygmy sperm whale). All of these cetaceans are known to dive to depths of at least 100 m where the underwater light field is dim and dominated by blue light. The knockout of both SWS1 and LWS in multiple cetacean lineages renders these taxa rod monochromats, a condition previously unknown among

  7. Characterisation of protein stability in rod-insert vaginal rings.

    PubMed

    Pattani, Aditya; Lowry, Deborah; Curran, Rhonda M; McGrath, Stephanie; Kett, Vicky L; Andrews, Gavin P; Malcolm, R Karl

    2012-07-01

    A major goal in vaccine development is elimination of the 'cold chain', the transport and storage system for maintenance and distribution of the vaccine product. This is particularly pertinent to liquid formulation of vaccines. We have previously described the rod-insert vaginal ring (RiR) device, comprising an elastomeric body into which are inserted lyophilised, rod-shaped, solid drug dosage forms, and having potential for sustained mucosal delivery of biomacromolecules, such as HIV envelope protein-based vaccine candidates. Given the solid, lyophilised nature of these insert dosage forms, we hypothesised that antigen stability may be significantly increased compared with more conventional solubilised vaginal gel format. In this study, we prepared and tested vaginal ring devices fitted with lyophilised rod inserts containing the model antigen bovine serum albumin (BSA). Both the RiRs and the gels that were freeze-dried to prepare the inserts were evaluated for BSA stability using PAGE, turbidimetry, microbial load, MALDI-TOF and qualitative precipitate solubility measurements. When stored at 4 °C, but not when stored at 40 °C/75% RH, the RiR formulation offered protection against structural and conformational changes to BSA. The insert also retained matrix integrity and release characteristics. The results demonstrate that lypophilised gels can provide relative protection against degradation at lower temperatures compared to semi-solid gels. The major mechanism of degradation at 40 °C/75% RH was shown to be protein aggregation. Finally, in a preliminary study, we found that addition of trehalose to the formulation significantly reduces the rate of BSA degradation compared to the original formulation when stored at 40 °C/75% RH. Establishing the mechanism of degradation, and finding that degradation is decelerated in the presence of trehalose, will help inform further development of RiRs specifically and polymer based freeze-dried systems in general. PMID

  8. Electrical responses of rods in the retina of Bufo marinus

    PubMed Central

    Cervetto, L.; Pasino, E.; Torre, V.

    1977-01-01

    1. Intracellular responses to flashes and steps of light have been recorded from the outer segment and the cell body of rods in the retina of the Bufo marinus. The identification of the origin of recorded responses has been confirmed by intracellular marking. 2. Responses to flashes delivered in darkness or superimposed on a background were analysed. Responses recorded from outer segments conform to the principle of `spectral univariance'. The shape of the response is not affected by enlarging the spot diameter from 150 to 1000 μm. 3. The membrane potential measured in darkness at the outer segments varied from -15 to -25 mV. Injection of steady hyperpolarizing currents increases the size of the response to light; depolarizing currents reduce the response. The mean value of the input resistance is 97 ± 30 MΩ in darkness and increases by 20-30% during illumination. 4. The responses obtained from the cell body of rods have the same shape, time course and spectral sensitivity of those recorded at the outer segment. Injection of steady current at the cell body produces different effects than at the outer segment: hyperpolarizing currents reduce the amplitude of the response to light; depolarizing currents increase the response. 5. The experimental data are fitted according to a model similar to that used to describe the responses of turtle cones (Baylor & Hodgkin, 1974; Baylor, Hodgkin & Lamb, 1974a, b). 6. The model reproduces the electrical responses of the rod outer segment to a variety of stimuli: (a) brief flashes and steps of light in dark adapted conditions; (b) bright flashes superimposed on background illuminations; (c) pairs of flashes delivered at different time intervals. Responses to hyperpolarizing steps of current are also reproduced by the model. ImagesABCD PMID:406383

  9. Rod monochromacy and the coevolution of cetacean retinal opsins.

    PubMed

    Meredith, Robert W; Gatesy, John; Emerling, Christopher A; York, Vincent M; Springer, Mark S

    2013-04-01

    Cetaceans have a long history of commitment to a fully aquatic lifestyle that extends back to the Eocene. Extant species have evolved a spectacular array of adaptations in conjunction with their deployment into a diverse array of aquatic habitats. Sensory systems are among those that have experienced radical transformations in the evolutionary history of this clade. In the case of vision, previous studies have demonstrated important changes in the genes encoding rod opsin (RH1), short-wavelength sensitive opsin 1 (SWS1), and long-wavelength sensitive opsin (LWS) in selected cetaceans, but have not examined the full complement of opsin genes across the complete range of cetacean families. Here, we report protein-coding sequences for RH1 and both color opsin genes (SWS1, LWS) from representatives of all extant cetacean families. We examine competing hypotheses pertaining to the timing of blue shifts in RH1 relative to SWS1 inactivation in the early history of Cetacea, and we test the hypothesis that some cetaceans are rod monochomats. Molecular evolutionary analyses contradict the "coastal" hypothesis, wherein SWS1 was pseudogenized in the common ancestor of Cetacea, and instead suggest that RH1 was blue-shifted in the common ancestor of Cetacea before SWS1 was independently knocked out in baleen whales (Mysticeti) and in toothed whales (Odontoceti). Further, molecular evidence implies that LWS was inactivated convergently on at least five occasions in Cetacea: (1) Balaenidae (bowhead and right whales), (2) Balaenopteroidea (rorquals plus gray whale), (3) Mesoplodon bidens (Sowerby's beaked whale), (4) Physeter macrocephalus (giant sperm whale), and (5) Kogia breviceps (pygmy sperm whale). All of these cetaceans are known to dive to depths of at least 100 m where the underwater light field is dim and dominated by blue light. The knockout of both SWS1 and LWS in multiple cetacean lineages renders these taxa rod monochromats, a condition previously unknown among

  10. An atomistic-continuum Cosserat rod model of carbon nanotubes

    NASA Astrophysics Data System (ADS)

    Chandraseker, Karthick; Mukherjee, Subrata; Paci, Jeffrey T.; Schatz, George C.

    2009-06-01

    The focus of the present work is an atomistic-continuum model of single-walled carbon nanotubes (CNTs) based on an elastic rod theory which can exhibit geometric as well as material nonlinearity [Healey, T.J., 2002. Material symmetry and chirality in nonlinearly elastic rods. Mathematics and Mechanics of Solids 7, 405-420]. In particular, the single-walled carbon nanotube (SWNT) is modeled as a one-dimensional elastic continuum with some finite thickness bounded by the lateral surface. Exploitation of certain symmetries in the underlying atomic structure leads to suitable representations of the continuum elastic strain energy density in terms of strain measures that capture extension, twist, bending, and shear deformations [Healey, T.J., 2002. Material symmetry and chirality in nonlinearly elastic rods. Mathematics and Mechanics of Solids 7, 405-420]. Bridging between the atomic scale and the effective continuum is carried out by parameterization of the continuum elastic energy and determination of the parameters using unit cell atomistic simulations over a range of deformation magnitudes and types. Specifically, the proposed model takes into account (a) bending, (b) twist, (c) shear, (d) extension, (e) coupled extension and twist, and (f) coupled bending and shear deformations. The extracted parameters reveal benefits of accounting for important anisotropic and large-strain effects as improvements over employing traditional, linearly elastic, isotropic, small-strain, continuum models to simulate deformations of atomic systems such as SWNTs. It is envisioned that the proposed approach and the extracted model parameters can serve as a useful input to simulations of SWNT deformations using existing nonlinearly elastic continuum codes based, for example, on the finite element method (FEM).

  11. Full-length fuel rod behavior under severe accident conditions

    SciTech Connect

    Lombardo, N J; Lanning, D D; Panisko, F E

    1992-12-01

    This document presents an assessment of the severe accident phenomena observed from four Full-Length High-Temperature (FLHT) tests that were performed by the Pacific Northwest Laboratory (PNL) in the National Research Universal (NRU) reactor at Chalk River, Ontario, Canada. These tests were conducted for the US Nuclear Regulatory Commission (NRC) as part of the Severe Accident Research Program. The objectives of the test were to simulate conditions and provide information on the behavior of full-length fuel rods during hypothetical, small-break, loss-of-coolant severe accidents, in commercial light water reactors.

  12. Fail-safe storage rack for irradiated fuel rod assemblies

    DOEpatents

    Lewis, D.R.

    1993-03-23

    A fail-safe storage rack is provided for interim storage of spent but radioactive nuclear fuel rod assemblies. The rack consists of a checkerboard array of substantially square, elongate receiving tubes fully enclosed by a double walled container, the outer wall of which is imperforate for liquid containment and the inner wall of which is provided with perforations for admitting moderator liquid flow to the elongate receiving tubes, the liquid serving to take up waste heat from the stored nuclear assemblies and dissipate same to the ambient liquid reservoir. A perforated cover sealing the rack facilitates cooling liquid entry and dissipation.

  13. Fail-safe storage rack for irradiated fuel rod assemblies

    DOEpatents

    Lewis, Donald R.

    1993-01-01

    A fail-safe storage rack is provided for interim storage of spent but radioactive nuclear fuel rod assemblies. The rack consists of a checkerboard array of substantially square, elongate receiving tubes fully enclosed by a double walled container, the outer wall of which is imperforate for liquid containment and the inner wall of which is provided with perforations for admitting moderator liquid flow to the elongate receiving tubes, the liquid serving to take up waste heat from the stored nuclear assemblies and dissipate same to the ambient liquid reservoir. A perforated cover sealing the rack facilitates cooling liquid entry and dissipation.

  14. Fail-safe storage rack for fuel rod assemblies

    SciTech Connect

    Lewis, D.R.

    1991-12-31

    This report discusses a fail-safe storage rack which is provided for interim storage of spent but radioactive nuclear fuel rod assemblies. The rack consists of a checkerboard array of substantially square, elongate receiving tubes fully enclosed by a double walled container, the outer wall of which is imperforate for liquid containment and the inner wall of which is provided with perforations for admitting moderator liquid flow to the elongate receiving tubes, the liquid serving to take up waste heat from the stored nuclear assemblies and dissipate same to the ambient liquid reservoir. A perforated cover sealing the rack facilitates cooling liquid entry and dissipation.

  15. Interaction modes between asymmetrically and oppositely charged rods

    NASA Astrophysics Data System (ADS)

    Antila, Hanne S.; Van Tassel, Paul R.; Sammalkorpi, Maria

    2016-02-01

    The interaction of oppositely and asymmetrically charged rods in salt—a simple model of (bio)macromolecular assembly—is observed via simulation to exhibit two free energy minima, separated by a repulsive barrier. In contrast to similar minima in the Derjaguin-Landau-Verwey-Overbeek (DLVO) theory, the governing mechanism includes electrostatic attraction at large separation, osmotic repulsion at close range, and depletion attraction near contact. A model accounting for ion condensation and excluded volume is shown to be superior to a mean-field treatment in predicting the effect of charge asymmetry on the free-energy profile.

  16. Automatic inspection system for nuclear fuel pellets or rods

    DOEpatents

    Miller, Jr., William H.; Sease, John D.; Hamel, William R.; Bradley, Ronnie A.

    1978-01-01

    An automatic inspection system is provided for determining surface defects on cylindrical objects such as nuclear fuel pellets or rods. The active element of the system is a compound ring having a plurality of pneumatic jet units directed into a central bore. These jet units are connected to provide multiple circuits, each circuit being provided with a pressure sensor. The outputs of the sensors are fed to a comparator circuit whereby a signal is generated when the difference of pressure between pneumatic circuits, caused by a defect, exceeds a pre-set amount. This signal may be used to divert the piece being inspected into a "reject" storage bin or the like.

  17. Elasticity of the Rod-Shaped Gram-Negative Eubacteria

    NASA Astrophysics Data System (ADS)

    Boulbitch, A.; Quinn, B.; Pink, D.

    2000-12-01

    We report a theoretical calculation of the elasticity of the peptidoglycan network, the only stress-bearing part of rod-shaped Gram-negative eubacteria. The peptidoglycan network consists of elastic peptides and inextensible glycan strands, and it has been proposed that the latter form zigzag filaments along the circumference of the cylindrical bacterial shell. The zigzag geometry of the glycan strands gives rise to nonlinear elastic behavior. The four elastic moduli of the peptidoglycan network depend on its stressed state. For a bacterium under physiological conditions the elasticity is proportional to the bacterial turgor pressure. Our results are in good agreement with recent measurements.

  18. Thin-rod Yb:YAG regenerative laser amplifier

    NASA Astrophysics Data System (ADS)

    Maruko, A.; Nishio, M.; Matsubara, S.; Tanaka, M.; Takama, M.; Yoshida, T.; Kyomoto, K.; Okunishi, H.; Kato, K.; Shimabayashi, K.; Morioka, M.; Inayoshi, S.; Yamagata, S.; Kawato, S.

    2014-09-01

    High-average-power, high-repetition-rates picosecond-pulsed regenerative ytterbium-doped yttrium aluminum garnet (Yb:YAG) laser amplifiers were developed. The architecture used in the amplifiers, which are named as thin-rod, has a unique cooling scheme like slab lasers and also has a unique pumping scheme like photonic crystal fiber lasers, is suitable for high-average power Ytterbium lasers. This architecture also has high gain characteristics which is appropriate for the regenerative spectral and pulse shaping on high-repetition-rate, ultrashort-pulse amplifications.

  19. Confined buckling of inextensible rods by convex difference algorithms

    NASA Astrophysics Data System (ADS)

    Alart, Pierre; Pagano, Stéphane

    2002-12-01

    In this Note we present an approach to determine the local minima of a specific class of minimization problems. Attention is focused on the inextensibility condition of flexible rods expressed as a nonconvex constraint. Two algorithms are derived from a special splitting of the Lagrangian into the difference of two convex functions (DC). They are compared to the augmented Lagrangian methods used in this context. These DC formulations are easily extended to contact problems and applied to the determination of confined buckling shapes. To cite this article: P. Alart, S. Pagano, C. R. Mecanique 330 (2002) 819-824.

  20. Flexible polymers and thin rods far from equilibrium: buckling dynamics

    PubMed

    Golubovic; Moldovan; Peredera

    2000-02-01

    We investigate the dynamics of the classical Euler buckling instability of compressed objects such as flexible molecular chains and thin rods moving in a viscous medium. We find that flexible chains undergo a coarsening process self-similar in time. They develop a wavelike pattern whose amplitude and wavelength grow in time. We relate the buckling dynamics to phase ordering phenomena. The role of the order parameter here is played by the chain slope with respect to the straight initial chain configuration. PMID:11046455

  1. Bacterial Flagella as a Model Rigid Rod of Tunable Shape

    NASA Astrophysics Data System (ADS)

    Schwenger, Walter; Yardimci, Sevim; Gibaud, Thomas; Snow, Henry; Urbach, Jeff; Dogic, Zvonimir

    In this research, we study the physical properties of suspensions of bacterial flagella from Salmonella typhimurium prepared in a variety of rigid polymorphic shapes. Flagella act as a rigid colloidal particle that can exhibit non-trivial geometry including helices of varying dimensions, straight rods, or a combination of the two in the same filament. By controlling the conditions in which flagella are prepared, the polymorphic shape assumed by the filament can be controlled. Utilizing different polymorphic shapes, we combine results from optical microscopy observations of single filaments with bulk rheological measurements to help understand the role that constituent colloidal geometry plays in complex bulk behavior.

  2. Compact Dielectric-Rod White-Light Delay Lines

    NASA Technical Reports Server (NTRS)

    Maleki, Lute; Matsko, Andrey; Savchenkov, Anatoliy; Strekalov, Dmitry

    2008-01-01

    Optical delay lines of a proposed type would be made from rods of such dielectric materials as calcium fluoride, fused silica, or sapphire. These would offer advantages over prior optical delay lines, as summarized below. Optical delay lines are key components of opto-electronic microwave oscillators, narrow-band opto-electronic microwave filters, evanescent-field optical biochemical detectors, and some Fourier-Transform spectrum analyzers. Heretofore, optical delay lines used in such applications have been of two types: resonators and coiled long optical fibers, both of which have disadvantages: Resonators are compact, but excitation must be provided by narrow-band lasers. Wide-band (including noisy) laser light cannot be coupled efficiently to narrow-band resonators. When light is coupled into a narrowband resonator from a source of reasonably high power, a significant amount of optical energy circulates within the resonator, causing nonlinear loss and significant noise. Typically, a coil-type optical delay line is made of fused-silica fiber, which exhibits fundamental loss. To overcome the limit imposed by the optical loss in fused silica, it would be necessary to use fibers having crystalline cores. Although space is saved by winding fibers into coils, fiber-coil delay lines are still inconveniently bulky. The proposed compact dielectric-rod delay lines would exploit the special class of non-diffracting light beams that are denoted Bessel beams because their amplitudes are proportional to Bessel functions of the radii from their central axes. High-order Bessel beams can have large values of angular momentum. They can be generated with the help of whispering-gallery-mode optical resonators, as described, for example, in "Simplified Generation of High-Angular-Momentum Light Beams" (NPO-42965) NASA Tech Briefs, Vol. 31, No. 3 (March 2007), page 8a. In a delay line according to the proposal, the dielectric rod would be dimensioned to function as a multimode

  3. Tensile Damage Effects in Steel Plate Perforation by a Tungsten Rod

    NASA Astrophysics Data System (ADS)

    Raftenberg, Martin N.

    1997-07-01

    The EPIC wavecode was used to simulate an experiment in which a tungsten rod impacted at 1.57 km/s and perforated a rolled homogeneous armor (RHA) plate. The rod's residual length, L_r, and the hole's final diameter, \\overlineD, were experimentally determined. The Johnson-Cook strength model was used for RHA with two sets of constants, J83 and G94. When the Johnson-Cook phfracture model was applied to RHA with damage constants recommended by Johnson and Cook, \\overlineD was 13% (J83) and 26% (G94) smaller than the experimental result. An alternative damage model introduces a material constant, p_fail. When the computed pressure within a given finite element of RHA attained a value more negative than p_fail, that element was no longer allowed to support hydrostatic tension or deviatoric stresses. Throughout the p_fail range of -4.0 to -1.0 GPa, \\overlineD remained consistently smaller than the experimental result. As p_fail was increased from -1.0 to -0.1 GPa, \\overlineD increased dramatically. Corresponding to some p_fail in the range of -0.5 to -0.1 GPa, the G94 value for each of \\overlineD and Lr achieved reasonable agreement with experiment. This applies to the J83 value as well in the case of \\overlineD. Microscopy suggests that such large spall pressures may occur locally because of adiabatic shear banding.

  4. Synthesis and Liquid-Crystal Behavior of Bent Colloidal Silica Rods.

    PubMed

    Yang, Yang; Chen, Guangdong; Martinez-Miranda, Luz J; Yu, Hua; Liu, Kun; Nie, Zhihong

    2016-01-13

    The design and assembly of novel colloidal particles are of both academic and technological interest. We developed a wet-chemical route to synthesize monodisperse bent rigid silica rods by controlled perturbation of emulsion-templated growth. The bending angle of the rods can be tuned in a range of 0-50° by varying the strength of perturbation in the reaction temperature or pH in the course of rod growth. The length of each arm of the bent rods can be individually controlled by adjusting the reaction time. For the first time we demonstrated that the bent silica rods resemble banana-shaped liquid-crystal molecules and assemble into ordered structures with a typical smectic B2 phase. The bent silica rods could serve as a visualizable mesoscopic model for exploiting the phase behaviors of bent molecules which represent a typical class of liquid-crystal molecules. PMID:26700616

  5. Ti-Ni Rods with Variable Stiffness for Spine Stabilization: Manufacture and Biomechanical Evaluation

    NASA Astrophysics Data System (ADS)

    Brailovski, Vladimir; Facchinello, Yann; Brummund, Martin; Petit, Yvan; Mac-Thiong, Jean-Marc

    2016-03-01

    A new concept of monolithic spinal rods with variable flexural stiffness is proposed to reduce the risk of adjacent segment degeneration and vertebral fracture, while providing adequate stability to the spine. The variability of mechanical properties is generated by locally annealing Ti-Ni shape memory alloy rods. Ten-minute Joule effect annealing allows the restoration of the superelasticity in the heated portion of the rod. Such processing also generates a mechanical property gradient between the heated and the unheated zones. A numerical model simulating the annealing temperature and the distributions of the mechanical properties was developed to optimize the Joule-heating strategy and to modulate the rod's overall flexural stiffness. Subsequently, the rod model was included in a finite element model of a porcine lumbar spine to study the effect of the rod's stiffness profiles on the spinal biomechanics.

  6. Study of the automatic measuring technique and instrument for an automobile shock-absorber connecting rod

    NASA Astrophysics Data System (ADS)

    Chen, Chan-Yao; Dai, Shuguang; Zhang, R. J.; Mu, Ping-An

    1993-09-01

    The autinobile shock absorber connecting rod makes very strict tolerance requirements on the diameter size, roundness, straightness. Because it is a kind of thin and long workpiece, it is difficult to measure the errors of the roundness and axis straightness. Furthermore, it brings much difficulty to realize the highly efficient autinatic measurment as the connecting rod is mass produced. Therefore, there is not any kind of connecting rod automatic measuring instrument available in China. In this article, the authors put forword the methods and principles which can autiatically and efficiently measure the above-mentioned errors of the connecting rod and have designed a reliable and simple automatic measuring instrument, Furthermore, the designing requirements and methods of the software and the electrical system are also introduced. The problem of the automatic measurement of the automobile shock absorber connecting rod has been solved. and it not only guarantees the quality of the rod, but also provides the basis for technical analysis of the product.

  7. Hydraulic lock for displacer rod drive mechanism (DRDM) and method of operation

    SciTech Connect

    Rinker, E.D.

    1990-12-18

    This paper describes a drive rod latch in combination with a nuclear reactor having a drive rod disposed in a rod housing characterized in that the drive rod has one end selectively exposed to a first, relatively low pressure zone of the reactor and another end thereof in communication with a second, relatively high pressure zone of the reactor. The drive rod further having disposed on an end thereof a valve member and the rod housing having disposed thereon a corresponding valve seat, and a control valve for selectively establishing communication between the housing and the first zone of the reactor whereby a pressure differential is created across the piston. The pressure differential being sufficient to seat the valve member against the valve seat to thereby establish a pressure boundary.

  8. Rod photoreceptors drive circadian photoentrainment across a wide range of light intensities

    PubMed Central

    Altimus, C.M.; Güler, A.D.; Alam, N.M.; Arman, A.C.; Prusky, G.T.; Sampath, A.P.; Hattar, S

    2010-01-01

    In mammals, synchronization of the circadian pacemaker in the hypothalamus is achieved through direct input from the eyes conveyed by intrinsically photosensitive retinal ganglion cells (ipRGCs). Circadian photoentrainment can be maintained by rod and cone photoreceptors, but their functional contributions and their retinal circuits that impinge on ipRGCs are not well understood. We demonstrate in genetic mouse models lacking functional rods, or where rods are the only functional photoreceptors, that rods are solely responsible for photoentrainment at scotopic light intensities. Surprisingly, rods were also capable of driving circadian photoentrainment at photopic intensities where they were incapable of supporting a visually–guided behavior. Using animals in which cone photoreceptors were ablated, we demonstrate that rods signal through cones at high light intensities, but not low light intensities. Thus two distinct retinal circuits drive ipRGC function to support circadian photoentrainment across a wide range of light intensities. PMID:20711184

  9. Materials and mechanical design analysis of boron carbide reactor safety rods. Final report

    SciTech Connect

    Marra, J.C.

    1992-04-01

    The purpose of this task was to analyze the materials and mechanical design bases for the new boron carbide safety rod. These analyses included examination of the irradiation response of the materials, chemical compatibility of component materials, moisture considerations for the boron carbide pellets and susceptibility of the rod to corrosion under reactor environmental conditions. A number of issues concerning the mechanical behavior were also addressed. These included: safety rod dynamic response in scram scenarios, flexibility and mishandling behavior, and response to thermal excursions associated with gamma heating. A surveillance program aimed at evaluating the integrity of the safety rods following actual operating conditions and justifying life extension for the rods was also proposed. Based on the experimental testing and analyses associated with this task, it is concluded that the boron carbide safety rod design meets the materials and mechanical criteria for successful operational performance.

  10. Simultaneous Processing Method for Micro-Rods and Holes Using EDM

    NASA Astrophysics Data System (ADS)

    Yamazaki, Minoru; Mori, Noritosi; Suzuki, Takemi; Kunieda, Masanori

    This paper describes a new method for micro-EDM drilling which utilizes the wear of rod electrodes. With this method, a pair of micro rod and micro hole can be machined in a single process, while with conventional methods, the micro rod electrode needs to be formed before machining the micro hole. Processing conditions were optimized for the new method to obtain higher aspect ratio for the micro rods. Results of experiments also showed the following: 1) This method can be applied to AISI1045, AISI304 and Kovar and any electrode diameter size. 2) From the second process, if machining many holes using the same electrode, the electrode shape can be regenerated with excellent repeatability and holes processed efficiently. 3) The influence of carbon adhering to the tip region of the rod electrode is large, which is why the rod electrode becomes needle sharp.

  11. Direct Evidence for Daily Plasticity of Electrical Coupling between Rod Photoreceptors in the Mammalian Retina

    PubMed Central

    Jin, Nan Ge

    2016-01-01

    Rod photoreceptors are electrically coupled through gap junctions. Coupling is a key determinant of their light response properties, but whether rod electrical coupling is dynamically regulated remains elusive and controversial. Here, we have obtained direct measurements of the conductance between adjacent rods in mouse retina and present evidence that rod electrical coupling strength is dependent on the time of day, the lighting conditions, and the mouse strain. Specifically, we show in CBA/Ca mice that under circadian conditions, the rod junctional conductance has a median value of 98 pS during the subjective day and of 493 pS during the subjective night. In C57BL/6 mice, the median junctional conductance between dark-adapted rods is ∼140 pS, regardless of the time in the circadian cycle. Adaptation to bright light decreases the rod junctional conductance to ∼0 pS, regardless of the time of day or the mouse strain. Together, these results establish the high degree of plasticity of rod electrical coupling over the course of the day. Estimates of the rod coupling strength will provide a foundation for further investigations of rod interactions and the role of rod coupling in the ability of the visual system to anticipate, assimilate, and respond to the daily changes in ambient light intensity. SIGNIFICANCE STATEMENT Many cells in the CNS communicate via gap junctions, or electrical synapses, the regulation of which remains largely unknown. Here, we show that the strength of electrical coupling between rod photoreceptors of the retina is regulated by the time of day and the lighting conditions. This mechanism may help us understand some key aspects of day and night vision as well as some visual malfunctions. PMID:26740659

  12. Considerations for sensitivity analysis, uncertainty quantification, and data assimilation for grid-to-rod fretting

    SciTech Connect

    Michael Pernice

    2012-10-01

    Grid-to-rod fretting is the leading cause of fuel failures in pressurized water reactors, and is one of the challenge problems being addressed by the Consortium for Advanced Simulation of Light Water Reactors to guide its efforts to develop a virtual reactor environment. Prior and current efforts in modeling and simulation of grid-to-rod fretting are discussed. Sources of uncertainty in grid-to-rod fretting are also described.

  13. Reduction of ahead of schedule anodes through anode rod quality control

    SciTech Connect

    Baillargeon, F.; Menard, Y.; Perron, C.; Proulx, A.L.

    1996-10-01

    One of the major causes of ahead of schedule anodes reported in recent years by the P155 potroom operation was related to the inherent weakness in the rod welded joints. The development and implementation of an apparatus and procedure to measure, detect and reject the faulty rods prior to anode rodding, will be presented and discussed. The technology has not only significantly reduced the number of ahead of schedule anodes, it has also provided useful information concerning other process improvements.

  14. Final Report: Contractor Readiness Assessment (CRA) for TREAT Fuel Movement and Control Rod Drives Isolation

    SciTech Connect

    Rowsell, David Leon

    2015-06-01

    This report documents the Contractor Readiness Assessment (CRA) for TREAT Fuel Movement and Control Rod Drives Isolation. The review followed the approved Plan of Action (POA) and Implementation Plan (IP) using the identified core requirements. The activity was limited scope focusing on the control rod drives functional isolation and fuel element movement. The purpose of this review is to ensure the facility's readiness to move fuel elements thus supporting inspection and functionally isolate the control rod drives to maintain the required shutdown margin.

  15. The analysis of failed nuclear fuel rods by gamma computed tomography

    NASA Astrophysics Data System (ADS)

    Dobrin, Relu; Craciunescu, Teddy; Tuturici, Ioan Liviu

    1997-07-01

    The failure of the cladding of an irradiated nuclear fuel rod can lead to the loss of some γ-radioactive fission products. Consequently the distribution of these fission products is altered in the cross-section of the fuel rod. The modification of the distribution, obtained by gamma computed tomography, is used to determine the integrity of the fuel cladding. The paper reports an experimental result, obtained for a CANDU-type fuel rod, irradiated in a TRIGA 14 MWth reactor.

  16. Growth of Bi2O3 rods using a trimethylbismuth and oxygen mixture

    NASA Astrophysics Data System (ADS)

    Kim, H. W.; Myung, J. H.; Shim, S. H.; Lee, C.

    2006-07-01

    We have successfully grown the rod-like structures of bismuth oxide (Bi2O3) on silicon substrate by a reaction of a trimethylbismuth (TMBi) and oxygen (O2) mixture without using any catalyst. We have characterized the samples by means of X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The products consisted of bundles of rod-like structures. The Bi2O3 rods were of monoclinic structure.

  17. The results of postirradiation examinations of VVER-1000 and VVER-440 fuel rods

    NASA Astrophysics Data System (ADS)

    Dubrovin, K. P.; Ivanov, E. G.; Strijov, P. N.; Yakovlev, V. V.

    1991-02-01

    The paper presents the results of postirradiation examination of the fuel rods having different fuel-cladding gaps, pellet densities, pellet inner diameters and so on. The fuel rods were irradiated in the material science reactor (MR) of the Kurchatov Institute of Atomic Energy and at 4 unit of the Novo-Voronezh nuclear powerplant. Some data on fission gas release and rod geometry and compared with computer code predictions.

  18. Method of bundling rods so as to form an optical fiber preform

    DOEpatents

    Kliner, Dahv A. V.; Koplow, Jeffery P.

    2004-03-30

    The present invention provides a simple method for fabricating fiber-optic glass preforms having complex refractive index configurations and/or dopant distributions in a radial direction with a high degree of accuracy and precision. The method teaches bundling together a plurality of glass rods of specific physical, chemical, or optical properties and wherein the rod bundle is fused in a manner that maintains the cross-sectional composition and refractive-index profiles established by the position of the rods.

  19. Displacement Maps in Taylor Impact Using Speckle Radiography

    NASA Astrophysics Data System (ADS)

    Grantham, S. G.; Braithwaite, C. H.; Proud, W. G.; Williamson, D. M.

    2006-07-01

    A method was developed at the Cavendish Laboratory (Cambridge University) to determine the internal displacement characteristics of a polymer rod undergoing classic Taylor impact. Using a layer of lead filings on the central plane of the rod and Digital Speckle Radiography with flash x-rays it was possible to build up a dynamic displacement map. This technique can be used to derive material properties such as yield strength and provide data for model validation.

  20. Process development and fabrication for sphere-pac fuel rods. [PWR; BWR

    SciTech Connect

    Welty, R.K.; Campbell, M.H.

    1981-06-01

    Uranium fuel rods containing sphere-pac fuel have been fabricated for in-reactor tests and demonstrations. A process for the development, qualification, and fabrication of acceptable sphere-pac fuel rods is described. Special equipment to control fuel contamination with moisture or air and the equipment layout needed for rod fabrication is described and tests for assuring the uniformity of the fuel column are discussed. Fuel retainers required for sphere-pac fuel column stability and instrumentation to measure fuel column smear density are described. Results of sphere-pac fuel rod fabrication campaigns are reviewed and recommended improvements for high throughput production are noted.