The long-solved problem of the best-fit straight line: Application to isotopic mixing lines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wehr, Richard; Saleska, Scott R.

It has been almost 50 years since York published an exact and general solution for the best-fit straight line to independent points with normally distributed errors in both x and y. York's solution is highly cited in the geophysical literature but almost unknown outside of it, so that there has been no ebb in the tide of books and papers wrestling with the problem. Much of the post-1969 literature on straight-line fitting has sown confusion not merely by its content but by its very existence. The optimal least-squares fit is already known; the problem is already solved. Here we introducemore » the non-specialist reader to York's solution and demonstrate its application in the interesting case of the isotopic mixing line, an analytical tool widely used to determine the isotopic signature of trace gas sources for the study of biogeochemical cycles. The most commonly known linear regression methods – ordinary least-squares regression (OLS), geometric mean regression (GMR), and orthogonal distance regression (ODR) – have each been recommended as the best method for fitting isotopic mixing lines. In fact, OLS, GMR, and ODR are all special cases of York's solution that are valid only under particular measurement conditions, and those conditions do not hold in general for isotopic mixing lines. Here, using Monte Carlo simulations, we quantify the biases in OLS, GMR, and ODR under various conditions and show that York's general – and convenient – solution is always the least biased.« less

The long-solved problem of the best-fit straight line: Application to isotopic mixing lines

DOE PAGES

Wehr, Richard; Saleska, Scott R.

2017-01-03

It has been almost 50 years since York published an exact and general solution for the best-fit straight line to independent points with normally distributed errors in both x and y. York's solution is highly cited in the geophysical literature but almost unknown outside of it, so that there has been no ebb in the tide of books and papers wrestling with the problem. Much of the post-1969 literature on straight-line fitting has sown confusion not merely by its content but by its very existence. The optimal least-squares fit is already known; the problem is already solved. Here we introducemore » the non-specialist reader to York's solution and demonstrate its application in the interesting case of the isotopic mixing line, an analytical tool widely used to determine the isotopic signature of trace gas sources for the study of biogeochemical cycles. The most commonly known linear regression methods – ordinary least-squares regression (OLS), geometric mean regression (GMR), and orthogonal distance regression (ODR) – have each been recommended as the best method for fitting isotopic mixing lines. In fact, OLS, GMR, and ODR are all special cases of York's solution that are valid only under particular measurement conditions, and those conditions do not hold in general for isotopic mixing lines. Here, using Monte Carlo simulations, we quantify the biases in OLS, GMR, and ODR under various conditions and show that York's general – and convenient – solution is always the least biased.« less

Parallel Hough Transform-Based Straight Line Detection and Its FPGA Implementation in Embedded Vision

PubMed Central

Lu, Xiaofeng; Song, Li; Shen, Sumin; He, Kang; Yu, Songyu; Ling, Nam

2013-01-01

Hough Transform has been widely used for straight line detection in low-definition and still images, but it suffers from execution time and resource requirements. Field Programmable Gate Arrays (FPGA) provide a competitive alternative for hardware acceleration to reap tremendous computing performance. In this paper, we propose a novel parallel Hough Transform (PHT) and FPGA architecture-associated framework for real-time straight line detection in high-definition videos. A resource-optimized Canny edge detection method with enhanced non-maximum suppression conditions is presented to suppress most possible false edges and obtain more accurate candidate edge pixels for subsequent accelerated computation. Then, a novel PHT algorithm exploiting spatial angle-level parallelism is proposed to upgrade computational accuracy by improving the minimum computational step. Moreover, the FPGA based multi-level pipelined PHT architecture optimized by spatial parallelism ensures real-time computation for 1,024 × 768 resolution videos without any off-chip memory consumption. This framework is evaluated on ALTERA DE2-115 FPGA evaluation platform at a maximum frequency of 200 MHz, and it can calculate straight line parameters in 15.59 ms on the average for one frame. Qualitative and quantitative evaluation results have validated the system performance regarding data throughput, memory bandwidth, resource, speed and robustness. PMID:23867746

Parallel Hough Transform-based straight line detection and its FPGA implementation in embedded vision.

PubMed

Lu, Xiaofeng; Song, Li; Shen, Sumin; He, Kang; Yu, Songyu; Ling, Nam

2013-07-17

Hough Transform has been widely used for straight line detection in low-definition and still images, but it suffers from execution time and resource requirements. Field Programmable Gate Arrays (FPGA) provide a competitive alternative for hardware acceleration to reap tremendous computing performance. In this paper, we propose a novel parallel Hough Transform (PHT) and FPGA architecture-associated framework for real-time straight line detection in high-definition videos. A resource-optimized Canny edge detection method with enhanced non-maximum suppression conditions is presented to suppress most possible false edges and obtain more accurate candidate edge pixels for subsequent accelerated computation. Then, a novel PHT algorithm exploiting spatial angle-level parallelism is proposed to upgrade computational accuracy by improving the minimum computational step. Moreover, the FPGA based multi-level pipelined PHT architecture optimized by spatial parallelism ensures real-time computation for 1,024 × 768 resolution videos without any off-chip memory consumption. This framework is evaluated on ALTERA DE2-115 FPGA evaluation platform at a maximum frequency of 200 MHz, and it can calculate straight line parameters in 15.59 ms on the average for one frame. Qualitative and quantitative evaluation results have validated the system performance regarding data throughput, memory bandwidth, resource, speed and robustness.

Multidirectional Scanning Model, MUSCLE, to Vectorize Raster Images with Straight Lines

PubMed Central

Karas, Ismail Rakip; Bayram, Bulent; Batuk, Fatmagul; Akay, Abdullah Emin; Baz, Ibrahim

2008-01-01

This paper presents a new model, MUSCLE (Multidirectional Scanning for Line Extraction), for automatic vectorization of raster images with straight lines. The algorithm of the model implements the line thinning and the simple neighborhood methods to perform vectorization. The model allows users to define specified criteria which are crucial for acquiring the vectorization process. In this model, various raster images can be vectorized such as township plans, maps, architectural drawings, and machine plans. The algorithm of the model was developed by implementing an appropriate computer programming and tested on a basic application. Results, verified by using two well known vectorization programs (WinTopo and Scan2CAD), indicated that the model can successfully vectorize the specified raster data quickly and accurately. PMID:27879843

Multidirectional Scanning Model, MUSCLE, to Vectorize Raster Images with Straight Lines.

PubMed

Karas, Ismail Rakip; Bayram, Bulent; Batuk, Fatmagul; Akay, Abdullah Emin; Baz, Ibrahim

2008-04-15

This paper presents a new model, MUSCLE (Multidirectional Scanning for Line Extraction), for automatic vectorization of raster images with straight lines. The algorithm of the model implements the line thinning and the simple neighborhood methods to perform vectorization. The model allows users to define specified criteria which are crucial for acquiring the vectorization process. In this model, various raster images can be vectorized such as township plans, maps, architectural drawings, and machine plans. The algorithm of the model was developed by implementing an appropriate computer programming and tested on a basic application. Results, verified by using two well known vectorization programs (WinTopo and Scan2CAD), indicated that the model can successfully vectorize the specified raster data quickly and accurately.

Handwritten text line segmentation by spectral clustering

NASA Astrophysics Data System (ADS)

Han, Xuecheng; Yao, Hui; Zhong, Guoqiang

2017-02-01

Since handwritten text lines are generally skewed and not obviously separated, text line segmentation of handwritten document images is still a challenging problem. In this paper, we propose a novel text line segmentation algorithm based on the spectral clustering. Given a handwritten document image, we convert it to a binary image first, and then compute the adjacent matrix of the pixel points. We apply spectral clustering on this similarity metric and use the orthogonal kmeans clustering algorithm to group the text lines. Experiments on Chinese handwritten documents database (HIT-MW) demonstrate the effectiveness of the proposed method.

Straight line foraging in yellow-eyed penguins: new insights into cascading fisheries effects and orientation capabilities of marine predators.

PubMed

Mattern, Thomas; Ellenberg, Ursula; Houston, David M; Lamare, Miles; Davis, Lloyd S; van Heezik, Yolanda; Seddon, Philip J

2013-01-01

Free-ranging marine predators rarely search for prey along straight lines because dynamic ocean processes usually require complex search strategies. If linear movement patterns occur they are usually associated with travelling events or migratory behaviour. However, recent fine scale tracking of flying seabirds has revealed straight-line movements while birds followed fishing vessels. Unlike flying seabirds, penguins are not known to target and follow fishing vessels. Yet yellow-eyed penguins from New Zealand often exhibit directed movement patterns while searching for prey at the seafloor, a behaviour that seems to contradict common movement ecology theories. While deploying GPS dive loggers on yellow-eyed penguins from the Otago Peninsula we found that the birds frequently followed straight lines for several kilometres with little horizontal deviation. In several cases individuals swam up and down the same line, while some of the lines were followed by more than one individual. Using a remote operated vehicle (ROV) we found a highly visible furrow on the seafloor most likely caused by an otter board of a demersal fish trawl, which ran in a straight line exactly matching the trajectory of a recent line identified from penguin tracks. We noted high abundances of benthic scavengers associated with fisheries-related bottom disturbance. While our data demonstrate the acute way-finding capabilities of benthic foraging yellow-eyed penguins, they also highlight how hidden cascading effects of coastal fisheries may alter behaviour and potentially even population dynamics of marine predators, an often overlooked fact in the examination of fisheries' impacts.

Pre-School Students' Informal Acquisitions Regarding the Concepts of Point and Straight Line

ERIC Educational Resources Information Center

Orbay, Keziban; Develi, Mehmet Hikmet

2015-01-01

This study aimed to investigate the informal cognitive structures regarding "point" and "straight line"--two basic and undefined terms of geometry--in children registered in preschool--the previous step before in-class formal education process. The study was conducted with the participation of 50 children enrolled in nursery,…

A Closed-Form Error Model of Straight Lines for Improved Data Association and Sensor Fusing

PubMed Central

2018-01-01

Linear regression is a basic tool in mobile robotics, since it enables accurate estimation of straight lines from range-bearing scans or in digital images, which is a prerequisite for reliable data association and sensor fusing in the context of feature-based SLAM. This paper discusses, extends and compares existing algorithms for line fitting applicable also in the case of strong covariances between the coordinates at each single data point, which must not be neglected if range-bearing sensors are used. Besides, in particular, the determination of the covariance matrix is considered, which is required for stochastic modeling. The main contribution is a new error model of straight lines in closed form for calculating quickly and reliably the covariance matrix dependent on just a few comprehensible and easily-obtainable parameters. The model can be applied widely in any case when a line is fitted from a number of distinct points also without a priori knowledge of the specific measurement noise. By means of extensive simulations, the performance and robustness of the new model in comparison to existing approaches is shown. PMID:29673205

System for line drawings interpretation

NASA Astrophysics Data System (ADS)

Boatto, L.; Consorti, Vincenzo; Del Buono, Monica; Eramo, Vincenzo; Esposito, Alessandra; Melcarne, F.; Meucci, Mario; Mosciatti, M.; Tucci, M.; Morelli, Arturo

1992-08-01

This paper describes an automatic system that extracts information from line drawings, in order to feed CAD or GIS systems. The line drawings that we analyze contain interconnected thin lines, dashed lines, text, and symbols. Characters and symbols may overlap with lines. Our approach is based on the properties of the run representation of a binary image that allow giving the image a graph structure. Using this graph structure, several algorithms have been designed to identify, directly in the raster image, straight segments, dashed lines, text, symbols, hatching lines, etc. Straight segments and dashed lines are converted into vectors, with high accuracy and good noise immunity. Characters and symbols are recognized by means of a recognizer, specifically developed for this application, designed to be insensitive to rotation and scaling. Subsequent processing steps include an `intelligent'' search through the graph in order to detect closed polygons, dashed lines, text strings, and other higher-level logical entities, followed by the identification of relationships (adjacency, inclusion, etc.) between them. Relationships are further translated into a formal description of the drawing. The output of the system can be used as input to a Geographic Information System package. The system is currently used by the Italian Land Register Authority to process cadastral maps.

Failure of the straight-line DCS boundary when extrapolated to the hypobaric realm.

PubMed

Conkin, J; Van Liew, H D

1992-11-01

The lowest pressure (P2) to which a diver can ascend without developing decompression sickness (DCS) after becoming equilibrated at some higher pressure (P1) is described by a straight line with a negative y-intercept. We tested whether extrapolation of such a line also predicts safe decompression to altitude. We substituted tissue nitrogen pressure (P1N2) calculated for a compartment with a 360-min half-time for P1 values; this allows data from hypobaric exposures to be plotted on a P2 vs. P1N2 graph, even if the subject breathes oxygen before ascent. In literature sources, we found 40 reports of human exposures in hypobaric chambers that fell in the region of a P2 vs. P1N2 plot where the extrapolation from hyperbaric data predicted that the decompression should be free of DCS. Of 4,576 exposures, 785 persons suffered decompression sickness (17%), indicating that extrapolation of the diver line to altitude is not valid. Over the pressure range spanned by human hypobaric exposures and hyperbaric air exposures, the best separation between no DCS and DCS on a P2 vs. P1N2 plot seems to be a curve which approximates a straight line in the hyperbaric region but bends toward the origin in the hypobaric region.

Thinking in a straight line.

PubMed

Chambers, David W

2013-01-01

Rational human discourse is not as common as we imagine or as we would like it to be. Sometimes it is necessary to use fallacies and fabrication to get to the point we favor. This essay is an illustrated list of 33 handy tools for avoiding thinking straight.

Straight trajectory planning for keyhole neurosurgery in sheep with automatic brain structures segmentation

NASA Astrophysics Data System (ADS)

Favaro, Alberto; Lad, Akash; Formenti, Davide; Zani, Davide Danilo; De Momi, Elena

2017-03-01

In a translational neuroscience/neurosurgery perspective, sheep are considered good candidates to study because of the similarity between their brain and the human one. Automatic planning systems for safe keyhole neurosurgery maximize the probe/catheter distance from vessels and risky structures. This work consists in the development of a trajectories planner for straight catheters placement intended to be used for investigating the drug diffusivity mechanisms in sheep brain. Automatic brain segmentation of gray matter, white matter and cerebrospinal fluid is achieved using an online available sheep atlas. Ventricles, midbrain and cerebellum segmentation have been also carried out. The veterinary surgeon is asked to select a target point within the white matter to be reached by the probe and to define an entry area on the brain cortex. To mitigate the risk of hemorrhage during the insertion process, which can prevent the success of the insertion procedure, the trajectory planner performs a curvature analysis of the brain cortex and wipes out from the poll of possible entry points the sulci, as part of brain cortex where superficial blood vessels are naturally located. A limited set of trajectories is then computed and presented to the surgeon, satisfying an optimality criteria based on a cost function which considers the distance from critical brain areas and the whole trajectory length. The planner proved to be effective in defining rectilinear trajectories accounting for the safety constraints determined by the brain morphology. It also demonstrated a short computational time and good capability in segmenting gyri and sulci surfaces.

Perception of straightness and parallelism with minimal distance information.

PubMed

Rogers, Brian; Naumenko, Olga

2016-07-01

The ability of human observers to judge the straightness and parallelism of extended lines has been a neglected topic of study since von Helmholtz's initial observations 150 years ago. He showed that there were significant misperceptions of the straightness of extended lines seen in the peripheral visual field. The present study focused on the perception of extended lines (spanning 90° visual angle) that were directly fixated in the visual environment of a planetarium where there was only minimal information about the distance to the lines. Observers were asked to vary the curvature of 1 or more lines until they appeared to be straight and/or parallel, ignoring any perceived curvature in depth. When the horizon between the ground and the sky was visible, the results showed that observers' judgements of the straightness of a single line were significantly biased away from the veridical, great circle locations, and towards equal elevation settings. Similar biases can be seen in the jet trails of aircraft flying across the sky and in Rogers and Anstis's new moon illusion (Perception, 42(Abstract supplement) 18, 2013, 2016). The biasing effect of the horizon was much smaller when observers were asked to judge the straightness and parallelism of 2 or more extended lines. We interpret the results as showing that, in the absence of adequate distance information, observers tend to perceive the projected lines as lying on an approximately equidistant, hemispherical surface and that their judgements of straightness and parallelism are based on the perceived separation of the lines superimposed on that surface.

Line drawing extraction from gray level images by feature integration

NASA Astrophysics Data System (ADS)

Yoo, Hoi J.; Crevier, Daniel; Lepage, Richard; Myler, Harley R.

1994-10-01

We describe procedures that extract line drawings from digitized gray level images, without use of domain knowledge, by modeling preattentive and perceptual organization functions of the human visual system. First, edge points are identified by standard low-level processing, based on the Canny edge operator. Edge points are then linked into single-pixel thick straight- line segments and circular arcs: this operation serves to both filter out isolated and highly irregular segments, and to lump the remaining points into a smaller number of structures for manipulation by later stages of processing. The next stages consist in linking the segments into a set of closed boundaries, which is the system's definition of a line drawing. According to the principles of Gestalt psychology, closure allows us to organize the world by filling in the gaps in a visual stimulation so as to perceive whole objects instead of disjoint parts. To achieve such closure, the system selects particular features or combinations of features by methods akin to those of preattentive processing in humans: features include gaps, pairs of straight or curved parallel lines, L- and T-junctions, pairs of symmetrical lines, and the orientation and length of single lines. These preattentive features are grouped into higher-level structures according to the principles of proximity, similarity, closure, symmetry, and feature conjunction. Achieving closure may require supplying missing segments linking contour concavities. Choices are made between competing structures on the basis of their overall compliance with the principles of closure and symmetry. Results include clean line drawings of curvilinear manufactured objects. The procedures described are part of a system called VITREO (viewpoint-independent 3-D recognition and extraction of objects).

Basic test framework for the evaluation of text line segmentation and text parameter extraction.

PubMed

Brodić, Darko; Milivojević, Dragan R; Milivojević, Zoran

2010-01-01

Text line segmentation is an essential stage in off-line optical character recognition (OCR) systems. It is a key because inaccurately segmented text lines will lead to OCR failure. Text line segmentation of handwritten documents is a complex and diverse problem, complicated by the nature of handwriting. Hence, text line segmentation is a leading challenge in handwritten document image processing. Due to inconsistencies in measurement and evaluation of text segmentation algorithm quality, some basic set of measurement methods is required. Currently, there is no commonly accepted one and all algorithm evaluation is custom oriented. In this paper, a basic test framework for the evaluation of text feature extraction algorithms is proposed. This test framework consists of a few experiments primarily linked to text line segmentation, skew rate and reference text line evaluation. Although they are mutually independent, the results obtained are strongly cross linked. In the end, its suitability for different types of letters and languages as well as its adaptability are its main advantages. Thus, the paper presents an efficient evaluation method for text analysis algorithms.

Basic Test Framework for the Evaluation of Text Line Segmentation and Text Parameter Extraction

PubMed Central

Brodić, Darko; Milivojević, Dragan R.; Milivojević, Zoran

2010-01-01

Text line segmentation is an essential stage in off-line optical character recognition (OCR) systems. It is a key because inaccurately segmented text lines will lead to OCR failure. Text line segmentation of handwritten documents is a complex and diverse problem, complicated by the nature of handwriting. Hence, text line segmentation is a leading challenge in handwritten document image processing. Due to inconsistencies in measurement and evaluation of text segmentation algorithm quality, some basic set of measurement methods is required. Currently, there is no commonly accepted one and all algorithm evaluation is custom oriented. In this paper, a basic test framework for the evaluation of text feature extraction algorithms is proposed. This test framework consists of a few experiments primarily linked to text line segmentation, skew rate and reference text line evaluation. Although they are mutually independent, the results obtained are strongly cross linked. In the end, its suitability for different types of letters and languages as well as its adaptability are its main advantages. Thus, the paper presents an efficient evaluation method for text analysis algorithms. PMID:22399932

Advantage of straight walk instability in turning maneuver of multilegged locomotion: a robotics approach

PubMed Central

Aoi, Shinya; Tanaka, Takahiro; Fujiki, Soichiro; Funato, Tetsuro; Senda, Kei; Tsuchiya, Kazuo

2016-01-01

Multilegged locomotion improves the mobility of terrestrial animals and artifacts. Using many legs has advantages, such as the ability to avoid falling and to tolerate leg malfunction. However, many intrinsic degrees of freedom make the motion planning and control difficult, and many contact legs can impede the maneuverability during locomotion. The underlying mechanism for generating agile locomotion using many legs remains unclear from biological and engineering viewpoints. The present study used a centipede-like multilegged robot composed of six body segments and twelve legs. The body segments are passively connected through yaw joints with torsional springs. The dynamic stability of the robot walking in a straight line changes through a supercritical Hopf bifurcation due to the body axis flexibility. We focused on a quick turning task of the robot and quantitatively investigated the relationship between stability and maneuverability in multilegged locomotion by using a simple control strategy. Our experimental results show that the straight walk instability does help the turning maneuver. We discuss the importance and relevance of our findings for biological systems and propose a design principle for a simple control scheme to create maneuverable locomotion of multilegged robots. PMID:27444746

Script-independent text line segmentation in freestyle handwritten documents.

PubMed

Li, Yi; Zheng, Yefeng; Doermann, David; Jaeger, Stefan; Li, Yi

2008-08-01

Text line segmentation in freestyle handwritten documents remains an open document analysis problem. Curvilinear text lines and small gaps between neighboring text lines present a challenge to algorithms developed for machine printed or hand-printed documents. In this paper, we propose a novel approach based on density estimation and a state-of-the-art image segmentation technique, the level set method. From an input document image, we estimate a probability map, where each element represents the probability that the underlying pixel belongs to a text line. The level set method is then exploited to determine the boundary of neighboring text lines by evolving an initial estimate. Unlike connected component based methods ( [1], [2] for example), the proposed algorithm does not use any script-specific knowledge. Extensive quantitative experiments on freestyle handwritten documents with diverse scripts, such as Arabic, Chinese, Korean, and Hindi, demonstrate that our algorithm consistently outperforms previous methods [1]-[3]. Further experiments show the proposed algorithm is robust to scale change, rotation, and noise.

Brain blood vessel segmentation using line-shaped profiles

NASA Astrophysics Data System (ADS)

Babin, Danilo; Pižurica, Aleksandra; De Vylder, Jonas; Vansteenkiste, Ewout; Philips, Wilfried

2013-11-01

Segmentation of cerebral blood vessels is of great importance in diagnostic and clinical applications, especially for embolization of cerebral aneurysms and arteriovenous malformations (AVMs). In order to perform embolization of the AVM, the structural and geometric information of blood vessels from 3D images is of utmost importance. For this reason, the in-depth segmentation of cerebral blood vessels is usually done as a fusion of different segmentation techniques, often requiring extensive user interaction. In this paper we introduce the idea of line-shaped profiling with an application to brain blood vessel and AVM segmentation, efficient both in terms of resolving details and in terms of computation time. Our method takes into account both local proximate and wider neighbourhood of the processed pixel, which makes it efficient for segmenting large blood vessel tree structures, as well as fine structures of the AVMs. Another advantage of our method is that it requires selection of only one parameter to perform segmentation, yielding very little user interaction.

Methods of Fitting a Straight Line to Data: Examples in Water Resources

USGS Publications Warehouse

Hirsch, Robert M.; Gilroy, Edward J.

1984-01-01

Three methods of fitting straight lines to data are described and their purposes are discussed and contrasted in terms of their applicability in various water resources contexts. The three methods are ordinary least squares (OLS), least normal squares (LNS), and the line of organic correlation (OC). In all three methods the parameters are based on moment statistics of the data. When estimation of an individual value is the objective, OLS is the most appropriate. When estimation of many values is the objective and one wants the set of estimates to have the appropriate variance, then OC is most appropriate. When one wishes to describe the relationship between two variables and measurement error is unimportant, then OC is most appropriate. Where the error is important in descriptive problems or in calibration problems, then structural analysis techniques may be most appropriate. Finally, if the problem is one of describing some geographic trajectory, then LNS is most appropriate.

Image Mosaic Method Based on SIFT Features of Line Segment

PubMed Central

Zhu, Jun; Ren, Mingwu

2014-01-01

This paper proposes a novel image mosaic method based on SIFT (Scale Invariant Feature Transform) feature of line segment, aiming to resolve incident scaling, rotation, changes in lighting condition, and so on between two images in the panoramic image mosaic process. This method firstly uses Harris corner detection operator to detect key points. Secondly, it constructs directed line segments, describes them with SIFT feature, and matches those directed segments to acquire rough point matching. Finally, Ransac method is used to eliminate wrong pairs in order to accomplish image mosaic. The results from experiment based on four pairs of images show that our method has strong robustness for resolution, lighting, rotation, and scaling. PMID:24511326

Numerical Simulations for Distribution Characteristics of Internal Forces on Segments of Tunnel Linings

NASA Astrophysics Data System (ADS)

Li, Shouju; Shangguan, Zichang; Cao, Lijuan

A procedure based on FEM is proposed to simulate interaction between concrete segments of tunnel linings and soils. The beam element named as Beam 3 in ANSYS software was used to simulate segments. The ground loss induced from shield tunneling and segment installing processes is simulated in finite element analysis. The distributions of bending moment, axial force and shear force on segments were computed by FEM. The commutated internal forces on segments will be used to design reinforced bars on shield linings. Numerically simulated ground settlements agree with observed values.

Generation of straight-line shifting bright-dark soliton trains with a wide dip in the symmetric center or dark solitons in optical fibers

NASA Astrophysics Data System (ADS)

Zhong, Xianqiong; Yao, Na; Sheng, Jia'nan; Cheng, Ke

2018-02-01

Nonlinear evolutions of dark soliton pulses with initially constant frequency chirps are investigated numerically for different soliton orders and chirp parameters in different dispersion regimes of optical fibers. The results show interestingly that, in the normal dispersion regime, the evolution properties remain unchanged apart from their straight-line shifts of the temporal trajectories compared with the chirp-free case. While in the anomalous dispersion regime, the dark solitons can evolve to bright-dark soliton trains with a wide black soliton in the symmetric center. The longer the distance, the more the pulse number. The larger the soliton order, the more the pulse number at the same distance. Similarly, straight-line shift of the temporal trajectory of the bright-dark soliton trains will also appear. The shifting amount and direction depend on the absolute value and the sign of the chirp parameter, respectively. This result inspires people to generate bright-dark soliton trains by using ordinary passive optical fibers instead of fiber lasers. Besides, this work also provides us an alternative approach to guide the formed solitons or soliton trains to move their temporal trajectories along straight lines.

Global solutions to the electrodynamic two-body problem on a straight line

NASA Astrophysics Data System (ADS)

Bauer, G.; Deckert, D.-A.; Dürr, D.; Hinrichs, G.

2017-06-01

The classical electrodynamic two-body problem has been a long standing open problem in mathematics. For motion constrained to the straight line, the interaction is similar to that of the two-body problem of classical gravitation. The additional complication is the presence of unbounded state-dependent delays in the Coulomb forces due to the finiteness of the speed of light. This circumstance renders the notion of local solutions meaningless, and therefore, straightforward ODE techniques cannot be applied. Here, we study the time-symmetric case, i.e., the Fokker-Schwarzschild-Tetrode (FST) equations, comprising both advanced and retarded delays. We extend the technique developed in Deckert and Hinrichs (J Differ Equ 260:6900-6929, 2016), where existence of FST solutions was proven on the half line, to ensure global existence—a result that had been obtained by Bauer (Ein Existenzsatz für die Wheeler-Feynman-Elektrodynamik, Herbert Utz Verlag, München, 1997). Due to the novel technique, the presented proof is shorter and more transparent but also relies on the idea to employ asymptotic data to characterize solutions.

Straight-line drift fences and pitfall traps

USGS Publications Warehouse

Corn, Paul Stephen

1994-01-01

Straight-line drift fences typically are short barriers (5-15 m) that direct animals traveling on the substrate surface into traps places at the ends of or beside the barriers. Traps (described below) can be pitfalls, funnel traps, or a combination of the two. Drift fences with pitfall or funnel traps and pitfall traps without fences are used commonly to inventory and monitor populations of amphibians and reptiles. For example, 9 of 17 field studies reported for management of terrestrial vertebrates (Sarzo et al. 1988) used these techniques to sample amphibians. Drift fences with pitfall traps can be used to determine species richness at a site and to detect the presence of rare species. They also can yield data on relative abundances and habitat use of selected species. Pitfall traps arrayed in a grid without fences can also be used to study the population ecology and habitat use of selected species. Population density can be estimated with this latter technique if used in conjunction with mark-recapture techniques (see Chapter 8). Drift fence arrays or pitfall grids can be left in place for long-term monitoring. In this section, I discuss the use of this technique to obtain data on amphibians away from breeding ponds. Use of drift fences and traps to monitory amphibian activity at breeding ponds is discussed in the section "Drift Fences Encircling Breeding Sits", below (technique 9). Some materials and procedures are common to both techniques. Investigators contemplating the use of drift fences and traps in any context should read both accounts.

Straight-line climbing flight aerodynamics of a fruit bat

NASA Astrophysics Data System (ADS)

Viswanath, K.; Nagendra, K.; Cotter, J.; Frauenthal, M.; Tafti, D. K.

2014-02-01

From flight data obtained on a fruit bat, Cynopterus brachyotis, a kinematic model for straight-line flapping motion is extracted and analyzed in a computational fluid dynamics (CFD) framework to gain insight into the complexity of bat flight. The intricate functional mechanics and architecture of the bat wings set it apart from other vertebrate flight. The extracted kinematic model is simulated for a range of Reynolds numbers, to observe the effect these phenomena have on the unsteady transient mechanisms of the flow produced by the flapping wings. The Strouhal number calculated from the data is high indicating that the oscillatory motion dominates the flow physics. From the obtained data, the bat exhibits fine control of its mechanics by actively varying wing camber, wing area, torsional rotation of the wing, forward and backward translational sweep of the wing, and wing conformation to dictate the fluid dynamics. As is common in flapping flight, the primary force generation is through the attached unsteady vortices on the wing surface. The bat through varying the wing camber and the wing area modulates this force output. The power requirement for the kinematics is analyzed and correlated with the aerodynamic performance.

A lane line segmentation algorithm based on adaptive threshold and connected domain theory

NASA Astrophysics Data System (ADS)

Feng, Hui; Xu, Guo-sheng; Han, Yi; Liu, Yang

2018-04-01

Before detecting cracks and repairs on road lanes, it's necessary to eliminate the influence of lane lines on the recognition result in road lane images. Aiming at the problems caused by lane lines, an image segmentation algorithm based on adaptive threshold and connected domain is proposed. First, by analyzing features like grey level distribution and the illumination of the images, the algorithm uses Hough transform to divide the images into different sections and convert them into binary images separately. It then uses the connected domain theory to amend the outcome of segmentation, remove noises and fill the interior zone of lane lines. Experiments have proved that this method could eliminate the influence of illumination and lane line abrasion, removing noises thoroughly while maintaining high segmentation precision.

Seeing a straight line on a curved surface: decoupling of patterns from surfaces by single IT neurons

PubMed Central

Ratan Murty, N. Apurva

2016-01-01

We have no difficulty seeing a straight line drawn on a paper even when the paper is bent, but this inference is in fact nontrivial. Doing so requires either matching local features or representing the pattern after factoring out the surface shape. Here we show that single neurons in the monkey inferior temporal (IT) cortex show invariant responses to patterns across rigid and nonrigid changes of surfaces. We recorded neuronal responses to stimuli in which the pattern and the surrounding surface were varied independently. In a subset of neurons, we found pattern-surface interactions that produced similar responses to stimuli across congruent pattern and surface transformations. These interactions produced systematic shifts in curvature tuning of patterns when overlaid on convex and flat surfaces. Our results show that surfaces are factored out of patterns by single neurons, thereby enabling complex perceptual inferences. NEW & NOTEWORTHY We have no difficulty seeing a straight line on a curved piece of paper, but in fact, doing so requires decoupling the shape of the surface from the pattern itself. Here we report a novel form of invariance in the visual cortex: single neurons in monkey inferior temporal cortex respond similarly to congruent transformations of patterns and surfaces, in effect decoupling patterns from the surface on which they are overlaid. PMID:27733595

An Approach to a Comprehensive Test Framework for Analysis and Evaluation of Text Line Segmentation Algorithms

PubMed Central

Brodic, Darko; Milivojevic, Dragan R.; Milivojevic, Zoran N.

2011-01-01

The paper introduces a testing framework for the evaluation and validation of text line segmentation algorithms. Text line segmentation represents the key action for correct optical character recognition. Many of the tests for the evaluation of text line segmentation algorithms deal with text databases as reference templates. Because of the mismatch, the reliable testing framework is required. Hence, a new approach to a comprehensive experimental framework for the evaluation of text line segmentation algorithms is proposed. It consists of synthetic multi-like text samples and real handwritten text as well. Although the tests are mutually independent, the results are cross-linked. The proposed method can be used for different types of scripts and languages. Furthermore, two different procedures for the evaluation of algorithm efficiency based on the obtained error type classification are proposed. The first is based on the segmentation line error description, while the second one incorporates well-known signal detection theory. Each of them has different capabilities and convenience, but they can be used as supplements to make the evaluation process efficient. Overall the proposed procedure based on the segmentation line error description has some advantages, characterized by five measures that describe measurement procedures. PMID:22164106

An approach to a comprehensive test framework for analysis and evaluation of text line segmentation algorithms.

PubMed

Brodic, Darko; Milivojevic, Dragan R; Milivojevic, Zoran N

2011-01-01

The paper introduces a testing framework for the evaluation and validation of text line segmentation algorithms. Text line segmentation represents the key action for correct optical character recognition. Many of the tests for the evaluation of text line segmentation algorithms deal with text databases as reference templates. Because of the mismatch, the reliable testing framework is required. Hence, a new approach to a comprehensive experimental framework for the evaluation of text line segmentation algorithms is proposed. It consists of synthetic multi-like text samples and real handwritten text as well. Although the tests are mutually independent, the results are cross-linked. The proposed method can be used for different types of scripts and languages. Furthermore, two different procedures for the evaluation of algorithm efficiency based on the obtained error type classification are proposed. The first is based on the segmentation line error description, while the second one incorporates well-known signal detection theory. Each of them has different capabilities and convenience, but they can be used as supplements to make the evaluation process efficient. Overall the proposed procedure based on the segmentation line error description has some advantages, characterized by five measures that describe measurement procedures.

Line Segmentation in Handwritten Assamese and Meetei Mayek Script Using Seam Carving Based Algorithm

NASA Astrophysics Data System (ADS)

Kumar, Chandan Jyoti; Kalita, Sanjib Kr.

Line segmentation is a key stage in an Optical Character Recognition system. This paper primarily concerns the problem of text line extraction on color and grayscale manuscript pages of two major North-east Indian regional Scripts, Assamese and Meetei Mayek. Line segmentation of handwritten text in Assamese and Meetei Mayek scripts is an uphill task primarily because of the structural features of both the scripts and varied writing styles. Line segmentation of a document image is been achieved by using the Seam carving technique, in this paper. Researchers from various regions used this approach for content aware resizing of an image. However currently many researchers are implementing Seam Carving for line segmentation phase of OCR. Although it is a language independent technique, mostly experiments are done over Arabic, Greek, German and Chinese scripts. Two types of seams are generated, medial seams approximate the orientation of each text line, and separating seams separated one line of text from another. Experiments are performed extensively over various types of documents and detailed analysis of the evaluations reflects that the algorithm performs well for even documents with multiple scripts. In this paper, we present a comparative study of accuracy of this method over different types of data.

Building Roof Segmentation from Aerial Images Using a Line-and Region-Based Watershed Segmentation Technique

PubMed Central

Merabet, Youssef El; Meurie, Cyril; Ruichek, Yassine; Sbihi, Abderrahmane; Touahni, Raja

2015-01-01

In this paper, we present a novel strategy for roof segmentation from aerial images (orthophotoplans) based on the cooperation of edge- and region-based segmentation methods. The proposed strategy is composed of three major steps. The first one, called the pre-processing step, consists of simplifying the acquired image with an appropriate couple of invariant and gradient, optimized for the application, in order to limit illumination changes (shadows, brightness, etc.) affecting the images. The second step is composed of two main parallel treatments: on the one hand, the simplified image is segmented by watershed regions. Even if the first segmentation of this step provides good results in general, the image is often over-segmented. To alleviate this problem, an efficient region merging strategy adapted to the orthophotoplan particularities, with a 2D modeling of roof ridges technique, is applied. On the other hand, the simplified image is segmented by watershed lines. The third step consists of integrating both watershed segmentation strategies into a single cooperative segmentation scheme in order to achieve satisfactory segmentation results. Tests have been performed on orthophotoplans containing 100 roofs with varying complexity, and the results are evaluated with the VINETcriterion using ground-truth image segmentation. A comparison with five popular segmentation techniques of the literature demonstrates the effectiveness and the reliability of the proposed approach. Indeed, we obtain a good segmentation rate of 96% with the proposed method compared to 87.5% with statistical region merging (SRM), 84% with mean shift, 82% with color structure code (CSC), 80% with efficient graph-based segmentation algorithm (EGBIS) and 71% with JSEG. PMID:25648706

Transition duct system with straight ceramic liner for delivering hot-temperature gases in a combustion turbine engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiebe, David J.

A transition duct system (10) for delivering hot-temperature gases from a plurality of combustors in a combustion turbine engine is provided. The system includes an exit piece (16) for each combustor. The exit piece may include a straight path segment (26) for receiving a gas flow from a respective combustor. A straight ceramic liner (40) may be inwardly disposed onto a metal outer shell (38) along the straight path segment of the exit piece. Structural arrangements are provided to securely attach the ceramic liner in the presence of substantial flow path pressurization. Cost-effective serviceability of the transition duct systems ismore » realizable since the liner can be readily removed and replaced as needed.« less

Setting the Record Straight. The Truth About Fad Diets.

ERIC Educational Resources Information Center

Wheat Foods Council, Parker, CO.

The Setting the Record Straight information packet presents facts to set the record straight about nutrition and debunk fad diets. The kit features materials designed to communicate the importance of balanced eating. Materials include: a time line of fad diets; four reproducible fad diet book review handouts that show the misleading claims rampant…

A method of plane geometry primitive presentation

NASA Astrophysics Data System (ADS)

Jiao, Anbo; Luo, Haibo; Chang, Zheng; Hui, Bin

2014-11-01

Point feature and line feature are basic elements in object feature sets, and they play an important role in object matching and recognition. On one hand, point feature is sensitive to noise; on the other hand, there are usually a huge number of point features in an image, which makes it complex for matching. Line feature includes straight line segment and curve. One difficulty in straight line segment matching is the uncertainty of endpoint location, the other is straight line segment fracture problem or short straight line segments joined to form long straight line segment. While for the curve, in addition to the above problems, there is another difficulty in how to quantitatively describe the shape difference between curves. Due to the problems of point feature and line feature, the robustness and accuracy of target description will be affected; in this case, a method of plane geometry primitive presentation is proposed to describe the significant structure of an object. Firstly, two types of primitives are constructed, they are intersecting line primitive and blob primitive. Secondly, a line segment detector (LSD) is applied to detect line segment, and then intersecting line primitive is extracted. Finally, robustness and accuracy of the plane geometry primitive presentation method is studied. This method has a good ability to obtain structural information of the object, even if there is rotation or scale change of the object in the image. Experimental results verify the robustness and accuracy of this method.

Straight-run vs. sex separate rearing for two broiler genetic lines Part 2: Economic analysis and processing advantages.

PubMed

Da Costa, M J; Colson, G; Frost, T J; Halley, J; Pesti, G M

2017-07-01

The objective of this analysis was to evaluate the effects of raising broilers under sex separate and straight-run conditions for 2 broiler genetic lines. One-day-old Ross 308 and Ross 708 chicks (n = 1,344) were sex separated and placed in 48 pens according to rearing type: sex separate (28 males or 28 females) or straight-run (14 males + 14 females). There were 3 dietary phases: starter (zero to 17 d), grower (17 to 32 d), and finisher (32 to 48 d). Bird individual BW and group feed intakes were measured at 12, 17, 25, 32, 42, and 48 d to evaluate performance. At 33, 43, and 49 d 4 birds per pen (straight-run pens 2 males + 2 females) were sampled for carcass yield evaluation. Data were analyzed using linear and non-linear regression in order to estimate feed intake and cut-up weights at 3 separate market weights (1,700, 2,700, and 3,700 g). Returns over feed cost were estimated for a 1.8 million broiler complex for each rearing system and under 9 feed/meat price scenarios. Overall, rearing birds that were sex separated resulted in extra income that ranged from ${\\$}$48,824 to ${\\$}$330,300 per week, depending on the market targeted and feed and meat price scenarios. Sex separation was shown to be especially important in disadvantageous scenarios in which feed prices were high. Gains from sex separation were markedly higher for the Ross 708 than for the Ross 308 broilers. Bird variability also was evaluated at the 3 separate market ages under narrow ranges of BW that were targeted. Straight-run birds decreased the number of birds present in the desired range. Depending on market weight, straight-run rearing resulted in 9.1 to 16.6% fewer birds than sex separate rearing to meet marketing goals. It was concluded that sex separation can result in increased company profitability and have possible beneficial effects at the processing plant due to increased bird uniformity. © 2017 Poultry Science Association Inc.

FogBank: a single cell segmentation across multiple cell lines and image modalities.

PubMed

Chalfoun, Joe; Majurski, Michael; Dima, Alden; Stuelten, Christina; Peskin, Adele; Brady, Mary

2014-12-30

Many cell lines currently used in medical research, such as cancer cells or stem cells, grow in confluent sheets or colonies. The biology of individual cells provide valuable information, thus the separation of touching cells in these microscopy images is critical for counting, identification and measurement of individual cells. Over-segmentation of single cells continues to be a major problem for methods based on morphological watershed due to the high level of noise in microscopy cell images. There is a need for a new segmentation method that is robust over a wide variety of biological images and can accurately separate individual cells even in challenging datasets such as confluent sheets or colonies. We present a new automated segmentation method called FogBank that accurately separates cells when confluent and touching each other. This technique is successfully applied to phase contrast, bright field, fluorescence microscopy and binary images. The method is based on morphological watershed principles with two new features to improve accuracy and minimize over-segmentation. First, FogBank uses histogram binning to quantize pixel intensities which minimizes the image noise that causes over-segmentation. Second, FogBank uses a geodesic distance mask derived from raw images to detect the shapes of individual cells, in contrast to the more linear cell edges that other watershed-like algorithms produce. We evaluated the segmentation accuracy against manually segmented datasets using two metrics. FogBank achieved segmentation accuracy on the order of 0.75 (1 being a perfect match). We compared our method with other available segmentation techniques in term of achieved performance over the reference data sets. FogBank outperformed all related algorithms. The accuracy has also been visually verified on data sets with 14 cell lines across 3 imaging modalities leading to 876 segmentation evaluation images. FogBank produces single cell segmentation from confluent cell

Strategies for Selecting Routes through Real-World Environments: Relative Topography, Initial Route Straightness, and Cardinal Direction

PubMed Central

Brunyé, Tad T.; Collier, Zachary A.; Cantelon, Julie; Holmes, Amanda; Wood, Matthew D.; Linkov, Igor; Taylor, Holly A.

2015-01-01

Previous research has demonstrated that route planners use several reliable strategies for selecting between alternate routes. Strategies include selecting straight rather than winding routes leaving an origin, selecting generally south- rather than north-going routes, and selecting routes that avoid traversal of complex topography. The contribution of this paper is characterizing the relative influence and potential interactions of these strategies. We also examine whether individual differences would predict any strategy reliance. Results showed evidence for independent and additive influences of all three strategies, with a strong influence of topography and initial segment straightness, and relatively weak influence of cardinal direction. Additively, routes were also disproportionately selected when they traversed relatively flat regions, had relatively straight initial segments, and went generally south rather than north. Two individual differences, extraversion and sense of direction, predicted the extent of some effects. Under real-world conditions navigators indeed consider a route’s initial straightness, cardinal direction, and topography, but these cues differ in relative influence and vary in their application across individuals. PMID:25992685

The conformal transformation of an airfoil into a straight line and its application to the inverse problem of airfoil theory

NASA Technical Reports Server (NTRS)

Mutterperl, William

1944-01-01

A method of conformal transformation is developed that maps an airfoil into a straight line, the line being chosen as the extended chord line of the airfoil. The mapping is accomplished by operating directly with the airfoil ordinates. The absence of any preliminary transformation is found to shorten the work substantially over that of previous methods. Use is made of the superposition of solutions to obtain a rigorous counterpart of the approximate methods of thin-airfoils theory. The method is applied to the solution of the direct and inverse problems for arbitrary airfoils and pressure distributions. Numerical examples are given. Applications to more general types of regions, in particular to biplanes and to cascades of airfoils, are indicated. (author)

Southeast Asian palm leaf manuscript images: a review of handwritten text line segmentation methods and new challenges

NASA Astrophysics Data System (ADS)

Kesiman, Made Windu Antara; Valy, Dona; Burie, Jean-Christophe; Paulus, Erick; Sunarya, I. Made Gede; Hadi, Setiawan; Sok, Kim Heng; Ogier, Jean-Marc

2017-01-01

Due to their specific characteristics, palm leaf manuscripts provide new challenges for text line segmentation tasks in document analysis. We investigated the performance of six text line segmentation methods by conducting comparative experimental studies for the collection of palm leaf manuscript images. The image corpus used in this study comes from the sample images of palm leaf manuscripts of three different Southeast Asian scripts: Balinese script from Bali and Sundanese script from West Java, both from Indonesia, and Khmer script from Cambodia. For the experiments, four text line segmentation methods that work on binary images are tested: the adaptive partial projection line segmentation approach, the A* path planning approach, the shredding method, and our proposed energy function for shredding method. Two other methods that can be directly applied on grayscale images are also investigated: the adaptive local connectivity map method and the seam carving-based method. The evaluation criteria and tool provided by ICDAR2013 Handwriting Segmentation Contest were used in this experiment.

Methodology for the Evaluation of the Algorithms for Text Line Segmentation Based on Extended Binary Classification

NASA Astrophysics Data System (ADS)

Brodic, D.

2011-01-01

Text line segmentation represents the key element in the optical character recognition process. Hence, testing of text line segmentation algorithms has substantial relevance. All previously proposed testing methods deal mainly with text database as a template. They are used for testing as well as for the evaluation of the text segmentation algorithm. In this manuscript, methodology for the evaluation of the algorithm for text segmentation based on extended binary classification is proposed. It is established on the various multiline text samples linked with text segmentation. Their results are distributed according to binary classification. Final result is obtained by comparative analysis of cross linked data. At the end, its suitability for different types of scripts represents its main advantage.

Optimal graph based segmentation using flow lines with application to airway wall segmentation.

PubMed

Petersen, Jens; Nielsen, Mads; Lo, Pechin; Saghir, Zaigham; Dirksen, Asger; de Bruijne, Marleen

2011-01-01

This paper introduces a novel optimal graph construction method that is applicable to multi-dimensional, multi-surface segmentation problems. Such problems are often solved by refining an initial coarse surface within the space given by graph columns. Conventional columns are not well suited for surfaces with high curvature or complex shapes but the proposed columns, based on properly generated flow lines, which are non-intersecting, guarantee solutions that do not self-intersect and are better able to handle such surfaces. The method is applied to segment human airway walls in computed tomography images. Comparison with manual annotations on 649 cross-sectional images from 15 different subjects shows significantly smaller contour distances and larger area of overlap than are obtained with recently published graph based methods. Airway abnormality measurements obtained with the method on 480 scan pairs from a lung cancer screening trial are reproducible and correlate significantly with lung function.

Design unbiased estimation in line intersect sampling using segmented transects

Treesearch

David L.R. Affleck; Timothy G. Gregoire; Harry T. Valentine; Harry T. Valentine

2005-01-01

In many applications of line intersect sampling. transects consist of multiple, connected segments in a prescribed configuration. The relationship between the transect configuration and the selection probability of a population element is illustrated and a consistent sampling protocol, applicable to populations composed of arbitrarily shaped elements, is proposed. It...

Layout pattern analysis using the Voronoi diagram of line segments

NASA Astrophysics Data System (ADS)

Dey, Sandeep Kumar; Cheilaris, Panagiotis; Gabrani, Maria; Papadopoulou, Evanthia

2016-01-01

Early identification of problematic patterns in very large scale integration (VLSI) designs is of great value as the lithographic simulation tools face significant timing challenges. To reduce the processing time, such a tool selects only a fraction of possible patterns which have a probable area of failure, with the risk of missing some problematic patterns. We introduce a fast method to automatically extract patterns based on their structure and context, using the Voronoi diagram of line-segments as derived from the edges of VLSI design shapes. Designers put line segments around the problematic locations in patterns called "gauges," along which the critical distance is measured. The gauge center is the midpoint of a gauge. We first use the Voronoi diagram of VLSI shapes to identify possible problematic locations, represented as gauge centers. Then we use the derived locations to extract windows containing the problematic patterns from the design layout. The problematic locations are prioritized by the shape and proximity information of the design polygons. We perform experiments for pattern selection in a portion of a 22-nm random logic design layout. The design layout had 38,584 design polygons (consisting of 199,946 line segments) on layer Mx, and 7079 markers generated by an optical rule checker (ORC) tool. The optical rules specify requirements for printing circuits with minimum dimension. Markers are the locations of some optical rule violations in the layout. We verify our approach by comparing the coverage of our extracted patterns to the ORC-generated markers. We further derive a similarity measure between patterns and between layouts. The similarity measure helps to identify a set of representative gauges that reduces the number of patterns for analysis.

Another Way to Divide a Line Segment into "n" Equal Parts

ERIC Educational Resources Information Center

Besteman, Nathan; Ferdinands, John

2005-01-01

Another way to divide a line segment discovered by Nathan Besteman is described along with Euclid's and the GLaD construction. The related projects and problems that teachers of geometry can assign to their students are also presented.

Empirical gradient threshold technique for automated segmentation across image modalities and cell lines.

PubMed

Chalfoun, J; Majurski, M; Peskin, A; Breen, C; Bajcsy, P; Brady, M

2015-10-01

New microscopy technologies are enabling image acquisition of terabyte-sized data sets consisting of hundreds of thousands of images. In order to retrieve and analyze the biological information in these large data sets, segmentation is needed to detect the regions containing cells or cell colonies. Our work with hundreds of large images (each 21,000×21,000 pixels) requires a segmentation method that: (1) yields high segmentation accuracy, (2) is applicable to multiple cell lines with various densities of cells and cell colonies, and several imaging modalities, (3) can process large data sets in a timely manner, (4) has a low memory footprint and (5) has a small number of user-set parameters that do not require adjustment during the segmentation of large image sets. None of the currently available segmentation methods meet all these requirements. Segmentation based on image gradient thresholding is fast and has a low memory footprint. However, existing techniques that automate the selection of the gradient image threshold do not work across image modalities, multiple cell lines, and a wide range of foreground/background densities (requirement 2) and all failed the requirement for robust parameters that do not require re-adjustment with time (requirement 5). We present a novel and empirically derived image gradient threshold selection method for separating foreground and background pixels in an image that meets all the requirements listed above. We quantify the difference between our approach and existing ones in terms of accuracy, execution speed, memory usage and number of adjustable parameters on a reference data set. This reference data set consists of 501 validation images with manually determined segmentations and image sizes ranging from 0.36 Megapixels to 850 Megapixels. It includes four different cell lines and two image modalities: phase contrast and fluorescent. Our new technique, called Empirical Gradient Threshold (EGT), is derived from this reference

Six rice chromosome segment substitution lines libraries with O. rufipogon introgressions

USDA-ARS?s Scientific Manuscript database

Chromosome segment substitution lines (CSSLs) are a powerful tool for identifying naturally occurring, favorable alleles in unadapted germplasm. Six CSSL libraries in rice (Oryza sativa) were developed from crosses between three different accessions ('Khao Pa', W1944, IRGC105567) of the rice progeni...

Novel approach to ambulatory assessment of human segmental orientation on a wearable sensor system.

PubMed

Liu, Kun; Liu, Tao; Shibata, Kyoko; Inoue, Yoshio; Zheng, Rencheng

2009-12-11

A new method using a double-sensor difference based algorithm for analyzing human segment rotational angles in two directions for segmental orientation analysis in the three-dimensional (3D) space was presented. A wearable sensor system based only on triaxial accelerometers was developed to obtain the pitch and yaw angles of thigh segment with an accelerometer approximating translational acceleration of the hip joint and two accelerometers measuring the actual accelerations on the thigh. To evaluate the method, the system was first tested on a 2 degrees of freedom mechanical arm assembled out of rigid segments and encoders. Then, to estimate the human segmental orientation, the wearable sensor system was tested on the thighs of eight volunteer subjects, who walked in a straight forward line in the work space of an optical motion analysis system at three self-selected speeds: slow, normal and fast. In the experiment, the subject was assumed to walk in a straight forward way with very little trunk sway, skin artifacts and no significant internal/external rotation of the leg. The root mean square (RMS) errors of the thigh segment orientation measurement were between 2.4 degrees and 4.9 degrees during normal gait that had a 45 degrees flexion/extension range of motion. Measurement error was observed to increase with increasing walking speed probably because of the result of increased trunk sway, axial rotation and skin artifacts. The results show that, without integration and switching between different sensors, using only one kind of sensor, the wearable sensor system is suitable for ambulatory analysis of normal gait orientation of thigh and shank in two directions of the segment-fixed local coordinate system in 3D space. It can then be applied to assess spatio-temporal gait parameters and monitoring the gait function of patients in clinical settings.

The challenge of global water access monitoring: evaluating straight-line distance versus self-reported travel time among rural households in Mozambique.

PubMed

Ho, Jeff C; Russel, Kory C; Davis, Jennifer

2014-03-01

Support is growing for the incorporation of fetching time and/or distance considerations in the definition of access to improved water supply used for global monitoring. Current efforts typically rely on self-reported distance and/or travel time data that have been shown to be unreliable. To date, however, there has been no head-to-head comparison of such indicators with other possible distance/time metrics. This study provides such a comparison. We examine the association between both straight-line distance and self-reported one-way travel time with measured route distances to water sources for 1,103 households in Nampula province, Mozambique. We find straight-line, or Euclidean, distance to be a good proxy for route distance (R(2) = 0.98), while self-reported travel time is a poor proxy (R(2) = 0.12). We also apply a variety of time- and distance-based indicators proposed in the literature to our sample data, finding that the share of households classified as having versus lacking access would differ by more than 70 percentage points depending on the particular indicator employed. This work highlights the importance of the ongoing debate regarding valid, reliable, and feasible strategies for monitoring progress in the provision of improved water supply services.

Morphology and Growth Kinetics of Straight and Kinked Tin Whiskers

NASA Astrophysics Data System (ADS)

Susan, Donald; Michael, Joseph; Grant, Richard P.; McKenzie, Bonnie; Yelton, W. Graham

2013-03-01

Time-lapse SEM studies of Sn whiskers were conducted to estimate growth kinetics and document whisker morphologies. For straight whiskers, growth rates of 3 to 4 microns per day were measured at room temperature. Two types of kinked whiskers were observed. For Type A kinks, the original growth segment spatial orientation remains unchanged, there are no other changes in morphology or diameter, and growth continues. For Type B kinks, the spatial orientation of the original segment changes and it appears that the whisker bends over. Whiskers with Type B kinks show changes in morphology and diameter at the base, indicating grain boundary motion in the film, which eliminates the conditions suitable for long-term whisker growth. To estimate the errors in the whisker growth measurements, a technique is presented to correct for SEM projection effects. With this technique, the actual growth angles and lengths of a large number of whiskers were collected. It was found that most whiskers grow at moderate or shallow angles with respect to the surface; few straight whiskers grow nearly normal to the surface. In addition, there is no simple correlation between growth angles and lengths for whiskers observed over an approximate 2-year period.

Electric field theory based approach to search-direction line definition in image segmentation: application to optimal femur-tibia cartilage segmentation in knee-joint 3-D MR

NASA Astrophysics Data System (ADS)

Yin, Y.; Sonka, M.

2010-03-01

A novel method is presented for definition of search lines in a variety of surface segmentation approaches. The method is inspired by properties of electric field direction lines and is applicable to general-purpose n-D shapebased image segmentation tasks. Its utility is demonstrated in graph construction and optimal segmentation of multiple mutually interacting objects. The properties of the electric field-based graph construction guarantee that inter-object graph connecting lines are non-intersecting and inherently covering the entire object-interaction space. When applied to inter-object cross-surface mapping, our approach generates one-to-one and all-to-all vertex correspondent pairs between the regions of mutual interaction. We demonstrate the benefits of the electric field approach in several examples ranging from relatively simple single-surface segmentation to complex multiobject multi-surface segmentation of femur-tibia cartilage. The performance of our approach is demonstrated in 60 MR images from the Osteoarthritis Initiative (OAI), in which our approach achieved a very good performance as judged by surface positioning errors (average of 0.29 and 0.59 mm for signed and unsigned cartilage positioning errors, respectively).

International Boundary Study. Series A. Limits in the Seas. Number 42, Straight Baselines: Ecuador.

DTIC Science & Technology

1972-05-23

point a straight line to Puntilla de Santa Elena; (d) A straight line from Puntilla de Santa Elena in the direction of Cabo Blanco ( Peru ) to the...published by the U.S. Navy Oceanographic Office. 1. The seaward extension of the Colombia-Ecuador land boundary into Bahia Ancon de Sardinas is not...Comments 1-2 81 Closes Bahia Ancon de Sardinas, which is neither a historical nor juridical bay, by connecting Cabo Manglares, Colombia (1) and Punta Galera

The straight line hypothesis elaborated: case reference obesity, an argument for acidosis, oxidative stress, and disease conglomeration?

PubMed

Berkemeyer, Shoma

2010-07-01

Studies report on the association between obesity and oxidative stress, with and without additional diseases. Macrophages in adipocytes, and hypoxia in adipose tissue have been suggested to explain how obesity can relate to oxidative stress. The straight line hypothesis using the lactic acid trap construct has been put forward to explain how proton imbalance can relate to obesity. Proton imbalance has been also reported to associate with the production of reactive oxygen species by inhibition of mitochondrial energy production. This review brings together existing literature and concepts to explain how obesity can relate to oxidative stress via protons, uniquely for itself or, as often observed, in conglomeration of additional diseases. Copyright 2010 Elsevier Ltd. All rights reserved.

Raft cultivation area extraction from high resolution remote sensing imagery by fusing multi-scale region-line primitive association features

NASA Astrophysics Data System (ADS)

Wang, Min; Cui, Qi; Wang, Jie; Ming, Dongping; Lv, Guonian

2017-01-01

In this paper, we first propose several novel concepts for object-based image analysis, which include line-based shape regularity, line density, and scale-based best feature value (SBV), based on the region-line primitive association framework (RLPAF). We then propose a raft cultivation area (RCA) extraction method for high spatial resolution (HSR) remote sensing imagery based on multi-scale feature fusion and spatial rule induction. The proposed method includes the following steps: (1) Multi-scale region primitives (segments) are obtained by image segmentation method HBC-SEG, and line primitives (straight lines) are obtained by phase-based line detection method. (2) Association relationships between regions and lines are built based on RLPAF, and then multi-scale RLPAF features are extracted and SBVs are selected. (3) Several spatial rules are designed to extract RCAs within sea waters after land and water separation. Experiments show that the proposed method can successfully extract different-shaped RCAs from HR images with good performance.

Optimal approaches for inline sampling of organisms in ballast water: L-shaped vs. Straight sample probes

NASA Astrophysics Data System (ADS)

Wier, Timothy P.; Moser, Cameron S.; Grant, Jonathan F.; Riley, Scott C.; Robbins-Wamsley, Stephanie H.; First, Matthew R.; Drake, Lisa A.

2017-10-01

Both L-shaped ("L") and straight ("Straight") sample probes have been used to collect water samples from a main ballast line in land-based or shipboard verification testing of ballast water management systems (BWMS). A series of experiments was conducted to quantify and compare the sampling efficiencies of L and Straight sample probes. The findings from this research-that both L and Straight probes sample organisms with similar efficiencies-permit increased flexibility for positioning sample probes aboard ships.

Straightness measurement using laser beam straight datum

NASA Astrophysics Data System (ADS)

Uchikoshi, Junichi; Shimada, Shoichi; Ikawa, Naoya; Komura, Akio

1995-08-01

Using the direction stabilized laser beam as a physical straight datum, instead of the tangible reference surface, a method is proposed for the measurement of an error motion of a slide table and/or surface profile of mechanical components. A specially designed 2D position sensor/compensator for laser beam center is developed combining a quadrant photo-diode (QPD) position sensor for beam center and the piezo-compensator which compensates the beam shift from the center of QPD. By the use the sensor/compensator proposed, the positional and angular fluctuations of laser beam path is evaluated with nanometric resolution. Combining the sensor with the piezo-driven mirror compensator, the directional stabilizer for the laser beam is also designed in the same manner as the sensor/compensator. The stabilized He-Ne laser beam can be used as the metrological datum of straightness within the accuracy of 2 X 10 -8 rad. By mounting the position sensor/compensator on a slide table, the carriage with working distance of 1 m is so designed and built as to move straight along the stabilized laser beam. The carriage can be used as a mechanical straight datum with the accuracy equivalent to the laser beam stability.

Neck Muscle Moment Arms Obtained In-Vivo from MRI: Effect of Curved and Straight Modeled Paths.

PubMed

Suderman, Bethany L; Vasavada, Anita N

2017-08-01

Musculoskeletal models of the cervical spine commonly represent neck muscles with straight paths. However, straight lines do not best represent the natural curvature of muscle paths in the neck, because the paths are constrained by bone and soft tissue. The purpose of this study was to estimate moment arms of curved and straight neck muscle paths using different moment arm calculation methods: tendon excursion, geometric, and effective torque. Curved and straight muscle paths were defined for two subject-specific cervical spine models derived from in vivo magnetic resonance images (MRI). Modeling neck muscle paths with curvature provides significantly different moment arm estimates than straight paths for 10 of 15 neck muscles (p < 0.05, repeated measures two-way ANOVA). Moment arm estimates were also found to be significantly different among moment arm calculation methods for 11 of 15 neck muscles (p < 0.05, repeated measures two-way ANOVA). In particular, using straight lines to model muscle paths can lead to overestimating neck extension moment. However, moment arm methods for curved paths should be investigated further, as different methods of calculating moment arm can provide different estimates.

Head and pelvic movement asymmetry during lungeing in horses with symmetrical movement on the straight.

PubMed

Rhodin, M; Roepstorff, L; French, A; Keegan, K G; Pfau, T; Egenvall, A

2016-05-01

Lungeing is commonly used as part of standard lameness examinations in horses. Knowledge of how lungeing influences motion symmetry in sound horses is needed. The aim of this study was to objectively evaluate the symmetry of vertical head and pelvic motion during lungeing in a large number of horses with symmetric motion during straight line evaluation. Cross-sectional prospective study. A pool of 201 riding horses, all functioning well and considered sound by their owners, were evaluated in trot on a straight line and during lungeing to the left and right. From this pool, horses with symmetric vertical head and pelvic movement during the straight line trot (n = 94) were retained for analysis. Vertical head and pelvic movements were measured with body mounted uniaxial accelerometers. Differences between vertical maximum and minimum head (HDmax, HDmin) and pelvic (PDmax, PDmin) heights between left and right forelimb and hindlimb stances were compared between straight line trot and lungeing in either direction. Vertical head and pelvic movements during lungeing were more asymmetric than during trot on a straight line. Common asymmetric patterns seen in the head were more upward movement during push-off of the outside forelimb and less downward movement during impact of the inside limb. Common asymmetric patterns seen in the pelvis were less upward movement during push-off of the outside hindlimb and less downward movement of the pelvis during impact of the inside hindlimb. Asymmetric patterns in one lunge direction were frequently not the same as in the opposite direction. Lungeing induces systematic asymmetries in vertical head and pelvic motion patterns in horses that may not be the same in both directions. These asymmetries may mask or mimic fore- or hindlimb lameness. © 2015 The Authors. Equine Veterinary Journal published by John Wiley & Sons Ltd on behalf of EVJ Ltd.

Line segment confidence region-based string matching method for map conflation

NASA Astrophysics Data System (ADS)

Huh, Yong; Yang, Sungchul; Ga, Chillo; Yu, Kiyun; Shi, Wenzhong

2013-04-01

In this paper, a method to detect corresponding point pairs between polygon object pairs with a string matching method based on a confidence region model of a line segment is proposed. The optimal point edit sequence to convert the contour of a target object into that of a reference object was found by the string matching method which minimizes its total error cost, and the corresponding point pairs were derived from the edit sequence. Because a significant amount of apparent positional discrepancies between corresponding objects are caused by spatial uncertainty and their confidence region models of line segments are therefore used in the above matching process, the proposed method obtained a high F-measure for finding matching pairs. We applied this method for built-up area polygon objects in a cadastral map and a topographical map. Regardless of their different mapping and representation rules and spatial uncertainties, the proposed method with a confidence level at 0.95 showed a matching result with an F-measure of 0.894.

Line Segmentation of 2d Laser Scanner Point Clouds for Indoor Slam Based on a Range of Residuals

NASA Astrophysics Data System (ADS)

Peter, M.; Jafri, S. R. U. N.; Vosselman, G.

2017-09-01

Indoor mobile laser scanning (IMLS) based on the Simultaneous Localization and Mapping (SLAM) principle proves to be the preferred method to acquire data of indoor environments at a large scale. In previous work, we proposed a backpack IMLS system containing three 2D laser scanners and an according SLAM approach. The feature-based SLAM approach solves all six degrees of freedom simultaneously and builds on the association of lines to planes. Because of the iterative character of the SLAM process, the quality and reliability of the segmentation of linear segments in the scanlines plays a crucial role in the quality of the derived poses and consequently the point clouds. The orientations of the lines resulting from the segmentation can be influenced negatively by narrow objects which are nearly coplanar with walls (like e.g. doors) which will cause the line to be tilted if those objects are not detected as separate segments. State-of-the-art methods from the robotics domain like Iterative End Point Fit and Line Tracking were found to not handle such situations well. Thus, we describe a novel segmentation method based on the comparison of a range of residuals to a range of thresholds. For the definition of the thresholds we employ the fact that the expected value for the average of residuals of n points with respect to the line is σ / √n. Our method, as shown by the experiments and the comparison to other methods, is able to deliver more accurate results than the two approaches it was tested against.

The pinwheel pupil discovery: exoplanet science & improved processing with segmented telescopes

NASA Astrophysics Data System (ADS)

Breckinridge, James Bernard

2018-01-01

In this paper, we show that by using a “pinwheel” architecture for the segmented primary mirror and curved supports for the secondary mirror, we can achieve a near uniform diffraction background in ground and space large telescope systems needed for high SNR exoplanet science. Also, the point spread function will be nearly rotationally symmetric, enabling improved digital image reconstruction. Large (>4-m) aperture space telescopes are needed to characterize terrestrial exoplanets by direct imaging coronagraphy. Launch vehicle volume constrains these apertures are segmented and deployed in space to form a large mirror aperture that is masked by the gaps between the hexagonal segments and the shadows of the secondary support system. These gaps and shadows over the pupil result in an image plane point spread function that has bright spikes, which may mask or obscure exoplanets.These telescope artifact mask faint exoplanets, making it necessary for the spacecraft to make a roll about the boresight and integrate again to make sure no planets are missed. This increases integration time, and requires expensive space-craft resources to do bore-sight roll.Currently the LUVOIR and HabEx studies have several significant efforts to develop special purpose A/O technology and to place complex absorbing apodizers over their Hex pupils to shape the unwanted diffracted light. These strong apodizers absorb light, decreasing system transmittance and reducing SNR. Implementing curved pupil obscurations will eliminate the need for the highly absorbing apodizers and thus result in higher SNR.Quantitative analysis of diffraction patterns that use the pinwheel architecture are compared to straight hex-segment edges with a straight-line secondary shadow mask to show a gain of over a factor of 100 by reducing the background. For the first-time astronomers are able to control and minimize image plane diffraction background “noise”. This technology will enable 10-m segmented

An image overall complexity evaluation method based on LSD line detection

NASA Astrophysics Data System (ADS)

Li, Jianan; Duan, Jin; Yang, Xu; Xiao, Bo

2017-04-01

In the artificial world, whether it is the city's traffic roads or engineering buildings contain a lot of linear features. Therefore, the research on the image complexity of linear information has become an important research direction in digital image processing field. This paper, by detecting the straight line information in the image and using the straight line as the parameter index, establishing the quantitative and accurate mathematics relationship. In this paper, we use LSD line detection algorithm which has good straight-line detection effect to detect the straight line, and divide the detected line by the expert consultation strategy. Then we use the neural network to carry on the weight training and get the weight coefficient of the index. The image complexity is calculated by the complexity calculation model. The experimental results show that the proposed method is effective. The number of straight lines in the image, the degree of dispersion, uniformity and so on will affect the complexity of the image.

Analysis of Precipitation (Rain and Snow) Levels and Straight-line Wind Speeds in Support of the 10-year Natural Phenomena Hazards Review for Los Alamos National Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kelly, Elizabeth J.; Dewart, Jean Marie; Deola, Regina

This report provides site-specific return level analyses for rain, snow, and straight-line wind extreme events. These analyses are in support of the 10-year review plan for the assessment of meteorological natural phenomena hazards at Los Alamos National Laboratory (LANL). These analyses follow guidance from Department of Energy, DOE Standard, Natural Phenomena Hazards Analysis and Design Criteria for DOE Facilities (DOE-STD-1020-2012), Nuclear Regulatory Commission Standard Review Plan (NUREG-0800, 2007) and ANSI/ ANS-2.3-2011, Estimating Tornado, Hurricane, and Extreme Straight-Line Wind Characteristics at Nuclear Facility Sites. LANL precipitation and snow level data have been collected since 1910, although not all years are complete.more » In this report the results from the more recent data (1990–2014) are compared to those of past analyses and a 2004 National Oceanographic and Atmospheric Administration report. Given the many differences in the data sets used in these different analyses, the lack of statistically significant differences in return level estimates increases confidence in the data and in the modeling and analysis approach.« less

Standing "Straight" up to Homophobia: Straight Allies' Involvement in GSAs

ERIC Educational Resources Information Center

Lapointe, Alicia Anne

2015-01-01

This qualitative study captures the experiences of four straight allies' and one gay youth involvement in gay--straight alliances (GSAs) at their Ontario, Canada, high schools. Participants' motivations for becoming GSA members and their roles as allies are examined. Queer theoretical perspectives, as espoused by Britzman (1995, 1998) and Linville…

Essential roles for lines in mediating leg and antennal proximodistal patterning and generating a stable Notch signaling interface at segment borders.

PubMed

Greenberg, Lina; Hatini, Victor

2009-06-01

The Drosophila leg imaginal disc provides a paradigm with which to understand the fundamental developmental mechanisms that generate an intricate appendage structure. Leg formation depends on the subdivision of the leg proximodistal (PD) axis into broad domains by the leg gap genes. The leg gap genes act combinatorially to initiate the expression of the Notch ligands Delta (Dl) and Serrate (Ser) in a segmental pattern. Dl and Ser induce the expression of a set of transcriptional regulators along the segment border, which mediate leg segment growth and joint morphogenesis. Here we show that Lines accumulates in nuclei in the presumptive tarsus and the inter-joints of proximal leg segments and governs the formation of these structures by destabilizing the nuclear protein Bowl. Across the presumptive tarsus, lines modulates the opposing expression landscapes of the leg gap gene dachshund (dac) and the tarsal PD genes, bric-a-brac 2 (bab), apterous (ap) and BarH1 (Bar). In this manner, lines inhibits proximal tarsal fates and promotes medial and distal tarsal fates. Across proximal leg segments, lines antagonizes bowl to promote Dl expression by relief-of-repression. In turn, Dl signals asymmetrically to stabilize Bowl in adjacent distal cells. Bowl, then, acts cell-autonomously, together with one or more redundant factors, to repress Dl expression. Together, lines and bowl act as a binary switch to generate a stable Notch signaling interface between Dl-expressing cells and adjacent distal cell. lines plays analogous roles in developing antennae, which are serially homologous to legs, suggesting evolutionarily conserved roles for lines in ventral appendage formation.

12. CONCRETE LINING ON A CURVING SEGMENT OF THE LATERAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. CONCRETE LINING ON A CURVING SEGMENT OF THE LATERAL NEAR THE NORTHEAST END OF LAKE LADORA (SECTION 2). - Highline Canal, Sand Creek Lateral, Beginning at intersection of Peoria Street & Highline Canal in Arapahoe County (City of Aurora), Sand Creek lateral Extends 15 miles Northerly through Araphoe County, City & County of Denver, & Adams County to its end point, approximately 1/4 mile Southest of intersectioin of D Street & Ninth Avenue in Adams County (Rocky Mountain Arsenal, Commerce City Vicinity), Commerce City, Adams County, CO

A multi-directional and multi-scale roughness filter to detect lineament segments on digital elevation models - analyzing spatial objects in R

NASA Astrophysics Data System (ADS)

Baumann, Sebastian; Robl, Jörg; Wendt, Lorenz; Willingshofer, Ernst; Hilberg, Sylke

2016-04-01

Automated lineament analysis on remotely sensed data requires two general process steps: The identification of neighboring pixels showing high contrast and the conversion of these domains into lines. The target output is the lineaments' position, extent and orientation. We developed a lineament extraction tool programmed in R using digital elevation models as input data to generate morphological lineaments defined as follows: A morphological lineament represents a zone of high relief roughness, whose length significantly exceeds the width. As relief roughness any deviation from a flat plane, defined by a roughness threshold, is considered. In our novel approach a multi-directional and multi-scale roughness filter uses moving windows of different neighborhood sizes to identify threshold limited rough domains on digital elevation models. Surface roughness is calculated as the vertical elevation difference between the center cell and the different orientated straight lines connecting two edge cells of a neighborhood, divided by the horizontal distance of the edge cells. Thus multiple roughness values depending on the neighborhood sizes and orientations of the edge connecting lines are generated for each cell and their maximum and minimum values are extracted. Thereby negative signs of the roughness parameter represent concave relief structures as valleys, positive signs convex relief structures as ridges. A threshold defines domains of high relief roughness. These domains are thinned to a representative point pattern by a 3x3 neighborhood filter, highlighting maximum and minimum roughness peaks, and representing the center points of lineament segments. The orientation and extent of the lineament segments are calculated within the roughness domains, generating a straight line segment in the direction of least roughness differences. We tested our algorithm on digital elevation models of multiple sources and scales and compared the results visually with shaded relief map

Photovoltaic panel extraction from very high-resolution aerial imagery using region-line primitive association analysis and template matching

NASA Astrophysics Data System (ADS)

Wang, Min; Cui, Qi; Sun, Yujie; Wang, Qiao

2018-07-01

In object-based image analysis (OBIA), object classification performance is jointly determined by image segmentation, sample or rule setting, and classifiers. Typically, as a crucial step to obtain object primitives, image segmentation quality significantly influences subsequent feature extraction and analyses. By contrast, template matching extracts specific objects from images and prevents shape defects caused by image segmentation. However, creating or editing templates is tedious and sometimes results in incomplete or inaccurate templates. In this study, we combine OBIA and template matching techniques to address these problems and aim for accurate photovoltaic panel (PVP) extraction from very high-resolution (VHR) aerial imagery. The proposed method is based on the previously proposed region-line primitive association framework, in which complementary information between region (segment) and line (straight line) primitives is utilized to achieve a more powerful performance than routine OBIA. Several novel concepts, including the mutual fitting ratio and best-fitting template based on region-line primitive association analyses, are proposed. Automatic template generation and matching method for PVP extraction from VHR imagery are designed for concept and model validation. Results show that the proposed method can successfully extract PVPs without any user-specified matching template or training sample. High user independency and accuracy are the main characteristics of the proposed method in comparison with routine OBIA and template matching techniques.

Vessel Segmentation in Retinal Images Using Multi-scale Line Operator and K-Means Clustering.

PubMed

Saffarzadeh, Vahid Mohammadi; Osareh, Alireza; Shadgar, Bita

2014-04-01

Detecting blood vessels is a vital task in retinal image analysis. The task is more challenging with the presence of bright and dark lesions in retinal images. Here, a method is proposed to detect vessels in both normal and abnormal retinal fundus images based on their linear features. First, the negative impact of bright lesions is reduced by using K-means segmentation in a perceptive space. Then, a multi-scale line operator is utilized to detect vessels while ignoring some of the dark lesions, which have intensity structures different from the line-shaped vessels in the retina. The proposed algorithm is tested on two publicly available STARE and DRIVE databases. The performance of the method is measured by calculating the area under the receiver operating characteristic curve and the segmentation accuracy. The proposed method achieves 0.9483 and 0.9387 localization accuracy against STARE and DRIVE respectively.

Structural design of an in-line bolted joint for the space shuttle solid rocket motor case segments

NASA Technical Reports Server (NTRS)

Dorsey, John T.; Stein, Peter A.; Bush, Harold G.

1987-01-01

Results of a structural design study of an in-line bolted joint concept which can be used to assemble Space Shuttle Solid Rocket Motor (SRM) case segments are presented. Numerous parametric studies are performed to characterize the in-line bolted joint behavior as major design variables are altered, with the primary objective always being to keep the inside of the joint (where the O-rings are located) closed during the SRM firing. The resulting design has 180 1-inch studs, an eccentricity of -0.5 inch, a flange thickness of 3/4 inch, a bearing plate thickness of 1/4 inch, and the studs are subjected to a preload which is 70% of ultimate. The mass penalty per case segment joint for the in-line design is 346 lbm more than the weight penalty for the proposed capture tang fix.

Retinal vascular segmentation using superpixel-based line operator and its application to vascular topology estimation.

PubMed

Na, Tong; Xie, Jianyang; Zhao, Yitian; Zhao, Yifan; Liu, Yue; Wang, Yongtian; Liu, Jiang

2018-05-09

Automatic methods of analyzing of retinal vascular networks, such as retinal blood vessel detection, vascular network topology estimation, and arteries/veins classification are of great assistance to the ophthalmologist in terms of diagnosis and treatment of a wide spectrum of diseases. We propose a new framework for precisely segmenting retinal vasculatures, constructing retinal vascular network topology, and separating the arteries and veins. A nonlocal total variation inspired Retinex model is employed to remove the image intensity inhomogeneities and relatively poor contrast. For better generalizability and segmentation performance, a superpixel-based line operator is proposed as to distinguish between lines and the edges, thus allowing more tolerance in the position of the respective contours. The concept of dominant sets clustering is adopted to estimate retinal vessel topology and classify the vessel network into arteries and veins. The proposed segmentation method yields competitive results on three public data sets (STARE, DRIVE, and IOSTAR), and it has superior performance when compared with unsupervised segmentation methods, with accuracy of 0.954, 0.957, and 0.964, respectively. The topology estimation approach has been applied to five public databases (DRIVE,STARE, INSPIRE, IOSTAR, and VICAVR) and achieved high accuracy of 0.830, 0.910, 0.915, 0.928, and 0.889, respectively. The accuracies of arteries/veins classification based on the estimated vascular topology on three public databases (INSPIRE, DRIVE and VICAVR) are 0.90.9, 0.910, and 0.907, respectively. The experimental results show that the proposed framework has effectively addressed crossover problem, a bottleneck issue in segmentation and vascular topology reconstruction. The vascular topology information significantly improves the accuracy on arteries/veins classification. © 2018 American Association of Physicists in Medicine.

Multisensory control of a straight locomotor trajectory.

PubMed

Hanna, Maxim; Fung, Joyce; Lamontagne, Anouk

2017-01-01

Locomotor steering is contingent upon orienting oneself spatially in the environment. When the head is turned while walking, the optic flow projected onto the retina is a complex pattern comprising of a translational and a rotational component. We have created a unique paradigm to simulate different optic flows in a virtual environment. We hypothesized that non-visual (vestibular and somatosensory) cues are required for proper control of a straight trajectory while walking. This research study included 9 healthy young subjects walking in a large physical space (40×25m2) while the virtual environment is viewed in a helmet-mounted display. They were instructed to walk straight in the physical world while being exposed to three conditions: (1) self-initiated active head turns (AHT: 40° right, left, or none); (2) visually simulated head turns (SHT); and (3) visually simulated head turns with no target element (SHT_NT). Conditions 1 and 2 involved an eye-level target which subjects were instructed to fixate, whereas condition 3 was similar to condition 2 but with no target. Identical retinal flow patterns were present in the AHT and SHT conditions whereas non-visual cues differed in that a head rotation was sensed only in AHT but not in SHT. Body motions were captured by a 12-camera Vicon system. Horizontal orientations of the head and body segments, as well as the trajectory of the body's centre of mass were analyzed. SHT and SNT_NT yielded similar results. Heading and body segment orientations changed in the direction opposite to the head turns in SHT conditions. Heading remained unchanged across head turn directions in AHT. Results suggest that non-visual information is used in the control of heading while being exposed to changing rotational optic flows. The small magnitude of the changes in SHT conditions suggests that the CNS can re-weight relevant sources of information to minimize heading errors in the presence of sensory conflicts.

Straight A's: Public Education Policy and Progress. Volume 12, Number 5

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2012-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) House Committee Passes Education Reform Legislation: On Party-Line Votes, Committee Passes Accountability and Teacher…

Exploring the power of rice (O. sativa x O. rufipogon) chromosome segment substitution line libraries

USDA-ARS?s Scientific Manuscript database

Transgressive variation was reported as an increase in grain yield for several rice (Oryza sativa x O. rufipogon) advanced backcross mapping populations. The objective of this study was to develop chromosome segment substitution line (CSSL) libraries to further dissect the reported transgressive var...

Transforaminal lumbar interbody graft placement using an articulating delivery arm facilitates increased segmental lordosis with superior anterior and midline graft placement.

PubMed

Shau, David N; Parker, Scott L; Mendenhall, Stephen K; Zuckerman, Scott L; Godil, Saniya S; Devin, Clinton J; McGirt, Matthew J

2015-05-01

Transforaminal lumbar interbody fusion (TLIF) is a frequently performed method of lumbar arthrodesis in patients failing medical management of back and leg pain. Accurate placement of the interbody graft and restoration of lordosis has been shown to be crucial when performing lumbar fusion procedures. We performed a single-surgeon, prospective, randomized study to determine whether a novel articulating versus traditional straight graft delivery arm system allows for superior graft placement and increased lordosis for single-level TLIF. Thirty consecutive patients undergoing single-level TLIF were included and prospectively randomized to one of the 2 groups (articulated vs. straight delivery arm system). Three radiographic characteristics were evaluated at 6-week follow-up: (1) degree of segmental lumbar lordosis at the fused level; (2) the percent anterior location of the interbody graft in disk space; and (3) the distance (mm) off midline of the interbody graft placement. Randomization yielded 16 patients in the articulated delivery arm cohort and 14 in the straight delivery arm cohort. The articulating delivery arm system yielded an average of 14.7-degree segmental lordosis at fused level, 35% anterior location, and 3.6 mm off midline. The straight delivery arm system yielded an average of 10.7-degree segmental lordosis at fused level, 46% anterior location, and 7.0 mm off midline. All 3 comparisons were statistically significant (P<0.05). The study suggests that an articulating delivery arm system facilitates superior anterior and midline TLIF graft placement allowing for increased segmental lordosis compared with a traditional straight delivery arm system.

Straight-run vs. sex separate rearing for 2 broiler genetic lines Part 1: Live production parameters, carcass yield, and feeding behavior.

PubMed

Da Costa, M J; Zaragoza-Santacruz, S; Frost, T J; Halley, J; Pesti, G M

2017-08-01

The objective of this experiment was to evaluate the effects of raising broilers under sex separate and straight-run conditions for 2 broiler strains. Day-old Ross 308 and Ross 708 chicks (n = 1,344) were separated by sex and placed in 48 pens according to the rearing type: sex separate (28 males or 28 females) or straight-run (14 males + 14 females). There were 3 dietary phases: starter (zero to 17 d), grower (17 to 32 d), and finisher (32 to 48 d). Birds' individual BW and feed intakes were measured at 12, 17, 25, 32, 42, and 48 d to evaluate performance. At 33, 43, and 49 d, 4 birds per pen were sampled for carcass yield evaluation. Additionally, from 06:00 to 06:30, 13:00 to 13:30, and 22:00 to 22:30, video records were taken to assess behavior at 45 days. Data were analyzed as CRD with a 2 × 3 factorial arrangement of treatments over time. Throughout the experiment Ross 308 were heavier than the 708, and after 17 d, male pens had the heavier birds, followed by straight-run and then females. Straight-run pens had higher BW CV in comparison with sex separate pens. Sex separate male BW was negatively impacted from 17 to 32 days. On the other hand, females raised sex separate were heavier than females raised straight-run with lower CV from 25 to 41 days. Post 25 d, FCR was the lowest in male pens whereas feed intake was the highest for these pens after 17 days. Overall, males had total carcass cut-up weights higher than straight-run and females at the 3 processing times. The Ross 708 had higher white meat yields, whereas 308 had higher yields for dark meat. Feeding behavior results were not consistent over time. However, from 13:00 to 13:30, birds in female pens spent more time eating, followed by straight-run and then males. In conclusion, raising females in a straight-run system negatively impacted performance and CV, whereas males benefited from straight-run rearing, with the differences being possibly related to feeder space competition. © 2017

Multiphase Oscillator Using Traveling Pulses Developed in a System of Transmission Lines with Regularly Spaced Resonant-tunneling Diodes

NASA Astrophysics Data System (ADS)

Narahara, Koichi

2017-06-01

A scheme is proposed for generating multiphase oscillatory signals in millimeter-wave frequencies based on the dynamics of a traveling pulse developed in a closed transmission line periodically loaded with resonant-tunneling diodes (RTDs) that is coupled with several straight RTD lines. When supplied with an appropriate voltage at the end of an RTD line, a pulse edge is shown to exhibit a spatially extended limit-cycle oscillation on the line. We consider the case where several RTD lines are connected halfway to a closed one at even intervals. In this case, the oscillatory edge developed in each straight RTD line is mutually synchronized such that a pulse-shaped rotary traveling wave develops on the closed RTD line. The oscillating edge on each straight line is also synchronized with the traveling pulse on the closed line, such that the leading edge of the traveling pulse on the closed line and the forward edge on the straight line pass the cross point simultaneously. As a result, when N L straight lines are connected to the closed line, the phase difference between two adjacent oscillatory edges becomes 2 π/ N L . On the other hand, the trailing edge of the traveling pulse at the cross point breaks the voltage wave on the straight line into two pieces, one of which travels forward to form a solitary wave and the other of which travels backward to reach the input end, where it is reflected and starts to travel forward and this forward moving edge is supposed to be synchronized with the leading edge of the traveling pulse. It means that a back-and-forth edge and a forward-moving solitary wave develop periodically on each straight line. Because the time required for the traveling pulse to go around the closed line must be coincident with the period of the edge oscillation on each straight line, a unique traveling pulse cannot synchronize with each oscillating edge when the cell size of the closed line becomes large, resulting in the development of multiple traveling

Two-dimensional compressible flow in centrifugal compressors with straight blades

NASA Technical Reports Server (NTRS)

Stanitz, John D; Ellis, Gaylord O

1950-01-01

Six numerical examples are presented for steady, two-dimensional, compressible, nonviscous flow in centrifugal compressors with thin straight blades, the center lines of which generate the surface of a right circular cone when rotated about the axis of the compressor. A seventh example is presented for incompressible flow. The solutions were obtained in a region of the compressors, including the impeller tip, that was considered to be unaffected by the diffuser vanes or by the impeller-inlet configuration. Each solution applies to radial and mixed flow compressors with various cone angles but with the same angle between blades on the conic flow surface. The solution also apply to radial and mixed flow turbines with the rotation and the flow direction reversed. The effects of variations in the following parameters were investigated: (1) flow rate, (2) impeller-tip speed, (3) variation of passage height with radius, and (4) angle between blades on conic flow surface. The numerical results are presented in plots of the streamlines and constant Mach number lines. Correlation equations are developed whereby the flow conditions in any impeller with straight blades can be determined (in the region investigated by this analysis) for all operating conditions.

Weighted straight skeletons in the plane☆

PubMed Central

Biedl, Therese; Held, Martin; Huber, Stefan; Kaaser, Dominik; Palfrader, Peter

2015-01-01

We investigate weighted straight skeletons from a geometric, graph-theoretical, and combinatorial point of view. We start with a thorough definition and shed light on some ambiguity issues in the procedural definition. We investigate the geometry, combinatorics, and topology of faces and the roof model, and we discuss in which cases a weighted straight skeleton is connected. Finally, we show that the weighted straight skeleton of even a simple polygon may be non-planar and may contain cycles, and we discuss under which restrictions on the weights and/or the input polygon the weighted straight skeleton still behaves similar to its unweighted counterpart. In particular, we obtain a non-procedural description and a linear-time construction algorithm for the straight skeleton of strictly convex polygons with arbitrary weights. PMID:25648398

Walking straight into circles.

PubMed

Souman, Jan L; Frissen, Ilja; Sreenivasa, Manish N; Ernst, Marc O

2009-09-29

Common belief has it that people who get lost in unfamiliar terrain often end up walking in circles. Although uncorroborated by empirical data, this belief has widely permeated popular culture. Here, we tested the ability of humans to walk on a straight course through unfamiliar terrain in two different environments: a large forest area and the Sahara desert. Walking trajectories of several hours were captured via global positioning system, showing that participants repeatedly walked in circles when they could not see the sun. Conversely, when the sun was visible, participants sometimes veered from a straight course but did not walk in circles. We tested various explanations for this walking behavior by assessing the ability of people to maintain a fixed course while blindfolded. Under these conditions, participants walked in often surprisingly small circles (diameter < 20 m), though rarely in a systematic direction. These results rule out a general explanation in terms of biomechanical asymmetries or other general biases [1-6]. Instead, they suggest that veering from a straight course is the result of accumulating noise in the sensorimotor system, which, without an external directional reference to recalibrate the subjective straight ahead, may cause people to walk in circles.

Map generation in unknown environments by AUKF-SLAM using line segment-type and point-type landmarks

NASA Astrophysics Data System (ADS)

Nishihta, Sho; Maeyama, Shoichi; Watanebe, Keigo

2018-02-01

Recently, autonomous mobile robots that collect information at disaster sites are being developed. Since it is difficult to obtain maps in advance in disaster sites, the robots being capable of autonomous movement under unknown environments are required. For this objective, the robots have to build maps, as well as the estimation of self-location. This is called a SLAM problem. In particular, AUKF-SLAM which uses corners in the environment as point-type landmarks has been developed as a solution method so far. However, when the robots move in an environment like a corridor consisting of few point-type features, the accuracy of self-location estimated by the landmark is decreased and it causes some distortions in the map. In this research, we propose AUKF-SLAM which uses walls in the environment as a line segment-type landmark. We demonstrate that the robot can generate maps in unknown environment by AUKF-SLAM, using line segment-type and point-type landmarks.

Flooding tolerance in interspecific introgression lines containing chromosome segments from teosinte (Zea nicaraguensis) in maize (Zea mays subsp. mays).

PubMed

Mano, Y; Omori, F

2013-10-01

Nicaraguan teosinte (Zea nicaraguensis), a species found in frequently flooded areas, provides useful germplasm for breeding flooding-tolerant maize (Z. mays subsp. mays). The objective of this study was to select flooding-tolerant lines using a library of introgression lines (ILs), each containing a chromosome segment from Z. nicaraguensis in the maize inbred line Mi29. To produce the ILs, a single F1 plant derived from a cross between maize Mi29 and Z. nicaraguensis was backcrossed to Mi29 three times, self-pollinated four times and genotyped using simple sequence repeat markers. Flooding tolerance was evaluated at the seedling stage under reducing soil conditions. By backcrossing and selfing, a series of 45 ILs were developed covering nearly the entire maize genome. Five flooding-tolerant lines were identified from among the ILs by evaluating leaf injury. Among these, line IL#18, containing a Z. nicaraguensis chromosome segment on the long arm of chromosome 4, showed the greatest tolerance to flooding, suggesting the presence of a major quantitative trait locus (QTL) in that region. The presence of the QTL was verified by examining flooding tolerance in a population segregating for the candidate region of chromosome 4. There was no significant relationship between the capacity to form constitutive aerenchyma and flooding tolerance in the ILs, indicating the presence of other factors related to flooding tolerance under reducing soil conditions. A flooding-tolerant genotype, IL#18, was identified; this genotype should be useful for maize breeding. In addition, because the chromosome segments of Z. nicaraguensis in the ILs cover nearly the entire genome and Z. nicaraguensis possesses several unique traits related to flooding tolerance, the ILs should be valuable material for additional QTL detection and the development of flooding-tolerant maize lines.

Flooding tolerance in interspecific introgression lines containing chromosome segments from teosinte (Zea nicaraguensis) in maize (Zea mays subsp. mays)

PubMed Central

Mano, Y.; Omori, F.

2013-01-01

Background and Aims Nicaraguan teosinte (Zea nicaraguensis), a species found in frequently flooded areas, provides useful germplasm for breeding flooding-tolerant maize (Z. mays subsp. mays). The objective of this study was to select flooding-tolerant lines using a library of introgression lines (ILs), each containing a chromosome segment from Z. nicaraguensis in the maize inbred line Mi29. Methods To produce the ILs, a single F1 plant derived from a cross between maize Mi29 and Z. nicaraguensis was backcrossed to Mi29 three times, self-pollinated four times and genotyped using simple sequence repeat markers. Flooding tolerance was evaluated at the seedling stage under reducing soil conditions. Key Results By backcrossing and selfing, a series of 45 ILs were developed covering nearly the entire maize genome. Five flooding-tolerant lines were identified from among the ILs by evaluating leaf injury. Among these, line IL#18, containing a Z. nicaraguensis chromosome segment on the long arm of chromosome 4, showed the greatest tolerance to flooding, suggesting the presence of a major quantitative trait locus (QTL) in that region. The presence of the QTL was verified by examining flooding tolerance in a population segregating for the candidate region of chromosome 4. There was no significant relationship between the capacity to form constitutive aerenchyma and flooding tolerance in the ILs, indicating the presence of other factors related to flooding tolerance under reducing soil conditions. Conclusions A flooding-tolerant genotype, IL#18, was identified; this genotype should be useful for maize breeding. In addition, because the chromosome segments of Z. nicaraguensis in the ILs cover nearly the entire genome and Z. nicaraguensis possesses several unique traits related to flooding tolerance, the ILs should be valuable material for additional QTL detection and the development of flooding-tolerant maize lines. PMID:23877074

Fluid Transient Analysis during Priming of Evacuated Line

NASA Technical Reports Server (NTRS)

Bandyopadhyay, Alak; Majumdar, Alok K.; Holt, Kimberley

2017-01-01

Water hammer analysis in pipe lines, in particularly during priming into evacuated lines is important for the design of spacecraft and other in-space application. In the current study, a finite volume network flow analysis code is used for modeling three different geometrical configurations: the first two being straight pipe, one with atmospheric air and other with evacuated line, and the third case is a representation of a complex flow network system. The numerical results show very good agreement qualitatively and quantitatively with measured data available in the literature. The peak pressure and impact time in case of straight pipe priming in evacuated line shows excellent agreement.

Automatic needle segmentation in 3D ultrasound images using 3D Hough transform

NASA Astrophysics Data System (ADS)

Zhou, Hua; Qiu, Wu; Ding, Mingyue; Zhang, Songgeng

2007-12-01

3D ultrasound (US) is a new technology that can be used for a variety of diagnostic applications, such as obstetrical, vascular, and urological imaging, and has been explored greatly potential in the applications of image-guided surgery and therapy. Uterine adenoma and uterine bleeding are the two most prevalent diseases in Chinese woman, and a minimally invasive ablation system using an RF button electrode which is needle-like is being used to destroy tumor cells or stop bleeding currently. Now a 3D US guidance system has been developed to avoid accidents or death of the patient by inaccurate localizations of the electrode and the tumor position during treatment. In this paper, we described two automated techniques, the 3D Hough Transform (3DHT) and the 3D Randomized Hough Transform (3DRHT), which is potentially fast, accurate, and robust to provide needle segmentation in 3D US image for use of 3D US imaging guidance. Based on the representation (Φ , θ , ρ , α ) of straight lines in 3D space, we used the 3DHT algorithm to segment needles successfully assumed that the approximate needle position and orientation are known in priori. The 3DRHT algorithm was developed to detect needles quickly without any information of the 3D US images. The needle segmentation techniques were evaluated using the 3D US images acquired by scanning water phantoms. The experiments demonstrated the feasibility of two 3D needle segmentation algorithms described in this paper.

Effects of fog, driver experience and gender on driving behavior on S-curved road segments.

PubMed

Li, Xiaomeng; Yan, Xuedong; Wong, S C

2015-04-01

Driving on curved roads has been recognized as a significant safety issue for many years. However, driver behavior and the interactions among variables that affect driver performance on curves is complicated and not well understood. Previous studies have investigated various factors that influence driver performance on right- or left-turn curves, but have paid little attention to the effects of foggy weather, driver experience and gender on driver performance on complex curves. A driving simulator experiment was conducted in this study to evaluate the relationships between driving behavior on a continuous S-curve and foggy weather, driver experience and gender. The process of negotiating a curve was divided into three stages consisting of a straight segment, the transition from the straight segment to the S-curve and the S-curve. The experimental results indicated that drivers tended to drive more cautiously in heavy fog, but the driving risk was still increased, especially in the transition stage from the straight segment to the S-curve. The non-professional (NP) drivers were less sensitive to the impending change in the road geometry, and less skilled in both longitudinal and lateral vehicle control than the professional drivers. The NP female drivers in particular were found to be the most vulnerable group in S-curve driving. Copyright © 2015 Elsevier Ltd. All rights reserved.

The Dipole Segment Model for Axisymmetrical Elongated Asteroids

NASA Astrophysics Data System (ADS)

Zeng, Xiangyuan; Zhang, Yonglong; Yu, Yang; Liu, Xiangdong

2018-02-01

Various simplified models have been investigated as a way to understand the complex dynamical environment near irregular asteroids. A dipole segment model is explored in this paper, one that is composed of a massive straight segment and two point masses at the extremities of the segment. Given an explicitly simple form of the potential function that is associated with the dipole segment model, five topological cases are identified with different sets of system parameters. Locations, stabilities, and variation trends of the system equilibrium points are investigated in a parametric way. The exterior potential distribution of nearly axisymmetrical elongated asteroids is approximated by minimizing the acceleration error in a test zone. The acceleration error minimization process determines the parameters of the dipole segment. The near-Earth asteroid (8567) 1996 HW1 is chosen as an example to evaluate the effectiveness of the approximation method for the exterior potential distribution. The advantages of the dipole segment model over the classical dipole and the traditional segment are also discussed. Percent error of acceleration and the degree of approximation are illustrated by using the dipole segment model to approximate four more asteroids. The high efficiency of the simplified model over the polyhedron is clearly demonstrated by comparing the CPU time.

Inner and outer segment junction (IS/OS line) integrity in ocular Behçet's disease.

PubMed

Yüksel, Harun; Türkcü, Fatih M; Sahin, Muhammed; Cinar, Yasin; Cingü, Abdullah K; Ozkurt, Zeynep; Sahin, Alparslan; Ari, Seyhmus; Caça, Ihsan

2014-08-01

In this study, we examined the spectral domain optical coherence tomography (OCT) findings of ocular Behçet's disease (OB) in patients with inactive uveitis. Specifically, we analyzed the inner and outer segment junction (IS/OS line) integrity and the effect of disturbed IS/OS line integrity on visual acuity. Patient files and OCT images of OB patients who had been followed-up between January and June of the year 2013 at the Dicle University Eye Clinic were evaluated retrospectively. Sixty-six eyes of 39 patients were included the study. OCT examination of the patients with inactive OB revealed that approximately 25% of the patients had disturbed IS/OS and external limiting membrane (EML) line integrity, lower visual acuity (VA), and lower macular thickness than others. Linear regression analysis revealed that macular thickness was not an independent variable for VA. In contrast, the IS/OS line integrity was an independent variable for VA in inactive OB patients. In this study, we showed that the IS/OS line integrity was an independent variable for VA in inactive OB patients. Further prospective studies are needed to evaluate the integrity of the IS/OS line in OB patients.

Fully automated chest wall line segmentation in breast MRI by using context information

NASA Astrophysics Data System (ADS)

Wu, Shandong; Weinstein, Susan P.; Conant, Emily F.; Localio, A. Russell; Schnall, Mitchell D.; Kontos, Despina

2012-03-01

Breast MRI has emerged as an effective modality for the clinical management of breast cancer. Evidence suggests that computer-aided applications can further improve the diagnostic accuracy of breast MRI. A critical and challenging first step for automated breast MRI analysis, is to separate the breast as an organ from the chest wall. Manual segmentation or user-assisted interactive tools are inefficient, tedious, and error-prone, which is prohibitively impractical for processing large amounts of data from clinical trials. To address this challenge, we developed a fully automated and robust computerized segmentation method that intensively utilizes context information of breast MR imaging and the breast tissue's morphological characteristics to accurately delineate the breast and chest wall boundary. A critical component is the joint application of anisotropic diffusion and bilateral image filtering to enhance the edge that corresponds to the chest wall line (CWL) and to reduce the effect of adjacent non-CWL tissues. A CWL voting algorithm is proposed based on CWL candidates yielded from multiple sequential MRI slices, in which a CWL representative is generated and used through a dynamic time warping (DTW) algorithm to filter out inferior candidates, leaving the optimal one. Our method is validated by a representative dataset of 20 3D unilateral breast MRI scans that span the full range of the American College of Radiology (ACR) Breast Imaging Reporting and Data System (BI-RADS) fibroglandular density categorization. A promising performance (average overlay percentage of 89.33%) is observed when the automated segmentation is compared to manually segmented ground truth obtained by an experienced breast imaging radiologist. The automated method runs time-efficiently at ~3 minutes for each breast MR image set (28 slices).

Building Bridges One Line at a Time

ERIC Educational Resources Information Center

Grigsby, Cathy Murray

2012-01-01

In this article, first-grade students were taught the different kinds of lines that were part of the construction of various bridges--the curved lines of the arches of stone bridges, straight lines connecting the cables of a suspension bridge, vertical lines, horizontal lines, and so on. They gained practice in drawing structures and in fine brush…

A power function profile of a ski jumping in-run hill.

PubMed

Zanevskyy, Ihor

2011-01-01

The aim of the research was to find a function of the curvilinear segment profile which could make possible to avoid an instantaneous increasing of a curvature and to replace a circle arc segment on the in-run of a ski jump without any correction of the angles of inclination and the length of the straight-line segments. The methods of analytical geometry and trigonometry were used to calculate an optimal in-run hill profile. There were two fundamental conditions of the model: smooth borders between a curvilinear segment and straight-line segments of an in-run hill and concave of the curvilinear segment. Within the framework of this model, the problem has been solved with a reasonable precision. Four functions of a curvilinear segment profile of the in-run hill were investigated: circle arc, inclined quadratic parabola, inclined cubic parabola, and power function. The application of a power function to the in-run profile satisfies equal conditions for replacing a circle arc segment. Geometrical parameters of 38 modern ski jumps were investigated using the methods proposed.

Geometric Hitting Set for Segments of Few Orientations

DOE PAGES

Fekete, Sandor P.; Huang, Kan; Mitchell, Joseph S. B.; ...

2016-01-13

Here we study several natural instances of the geometric hitting set problem for input consisting of sets of line segments (and rays, lines) having a small number of distinct slopes. These problems model path monitoring (e.g., on road networks) using the fewest sensors (the \\hitting points"). We give approximation algorithms for cases including (i) lines of 3 slopes in the plane, (ii) vertical lines and horizontal segments, (iii) pairs of horizontal/vertical segments. Lastly, we give hardness and hardness of approximation results for these problems. We prove that the hitting set problem for vertical lines and horizontal rays is polynomially solvable.

Straight Talk

ERIC Educational Resources Information Center

Stainburn, Samantha

2005-01-01

Recognizing gay students remains an emotional, politically charged issue. But Kevin Jennings, the 42-year-old executive director of the Gay, Lesbian, and Straight Education Network (GLSEN), is not out to provoke shouting matches. Instead, he is quietly turning students into activists capable of changing schools on their own. Along with advocating…

Automated detection of jet contrails using the AVHRR split window

NASA Technical Reports Server (NTRS)

Engelstad, M.; Sengupta, S. K.; Lee, T.; Welch, R. M.

1992-01-01

This paper investigates the automated detection of jet contrails using data from the Advanced Very High Resolution Radiometer. A preliminary algorithm subtracts the 11.8-micron image from the 10.8-micron image, creating a difference image on which contrails are enhanced. Then a three-stage algorithm searches the difference image for the nearly-straight line segments which characterize contrails. First, the algorithm searches for elevated, linear patterns called 'ridges'. Second, it applies a Hough transform to the detected ridges to locate nearly-straight lines. Third, the algorithm determines which of the nearly-straight lines are likely to be contrails. The paper applies this technique to several test scenes.

49 CFR 179.201-3 - Lined tanks.

Code of Federal Regulations, 2011 CFR

2011-10-01

...-Pressure Tank Car Tanks (Classes DOT-111AW and 115AW) § 179.201-3 Lined tanks. (a) Rubber-lined tanks. (1) Each tank or each compartment thereof must be lined with acid-resistant rubber or other approved rubber... double thickness. The rubber lining must overlap at least 11/2 inches at all edges which must be straight...

49 CFR 179.201-3 - Lined tanks.

Code of Federal Regulations, 2012 CFR

2012-10-01

...-Pressure Tank Car Tanks (Classes DOT-111AW and 115AW) § 179.201-3 Lined tanks. (a) Rubber-lined tanks. (1) Each tank or each compartment thereof must be lined with acid-resistant rubber or other approved rubber... double thickness. The rubber lining must overlap at least 11/2 inches at all edges which must be straight...

49 CFR 179.201-3 - Lined tanks.

Code of Federal Regulations, 2013 CFR

2013-10-01

...-Pressure Tank Car Tanks (Classes DOT-111AW and 115AW) § 179.201-3 Lined tanks. (a) Rubber-lined tanks. (1) Each tank or each compartment thereof must be lined with acid-resistant rubber or other approved rubber... double thickness. The rubber lining must overlap at least 11/2 inches at all edges which must be straight...

49 CFR 179.201-3 - Lined tanks.

Code of Federal Regulations, 2014 CFR

2014-10-01

...-Pressure Tank Car Tanks (Classes DOT-111AW and 115AW) § 179.201-3 Lined tanks. (a) Rubber-lined tanks. (1) Each tank or each compartment thereof must be lined with acid-resistant rubber or other approved rubber... double thickness. The rubber lining must overlap at least 11/2 inches at all edges which must be straight...

Power spectrum weighted edge analysis for straight edge detection in images

NASA Astrophysics Data System (ADS)

Karvir, Hrishikesh V.; Skipper, Julie A.

2007-04-01

Most man-made objects provide characteristic straight line edges and, therefore, edge extraction is a commonly used target detection tool. However, noisy images often yield broken edges that lead to missed detections, and extraneous edges that may contribute to false target detections. We present a sliding-block approach for target detection using weighted power spectral analysis. In general, straight line edges appearing at a given frequency are represented as a peak in the Fourier domain at a radius corresponding to that frequency, and a direction corresponding to the orientation of the edges in the spatial domain. Knowing the edge width and spacing between the edges, a band-pass filter is designed to extract the Fourier peaks corresponding to the target edges and suppress image noise. These peaks are then detected by amplitude thresholding. The frequency band width and the subsequent spatial filter mask size are variable parameters to facilitate detection of target objects of different sizes under known imaging geometries. Many military objects, such as trucks, tanks and missile launchers, produce definite signatures with parallel lines and the algorithm proves to be ideal for detecting such objects. Moreover, shadow-casting objects generally provide sharp edges and are readily detected. The block operation procedure offers advantages of significant reduction in noise influence, improved edge detection, faster processing speed and versatility to detect diverse objects of different sizes in the image. With Scud missile launcher replicas as target objects, the method has been successfully tested on terrain board test images under different backgrounds, illumination and imaging geometries with cameras of differing spatial resolution and bit-depth.

Development of an extended straightness measurement reference

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schenz, R.F.; Griffith, L.V.; Sommargren, G.E.

1988-09-06

The most accurate diamond turning machines have used physical straightness references. These references commonly are made of optical materials, such as Zerodur, and are flat enough to permit straightness measurements with an accuracy of 100--150 nm (4--6 microinches) p-v. In most cases, the flatness error is stable and can be accommodated by using a calibration table. The straightedges for the Large Optics Diamond Turning Machine (LODTM) at Lawrence Livermore National Laboratory (LLNL) are 1.1 meters in length and allow a straightness reference accuracy of 25--50 nm (1--2 microinches) p-v after calibration. Fabrication problems become insurmountable when a straightness reference formore » a length of up to 4 meters is desired. Moreover, the method of calibration by straightedge reversal does not account for gravitational sag when the sensing direction is vertical. Vertical sensing would be required in a four meter system and sag would become unacceptably large. Recent developments published in the literature suggest that the use of a laser beam for a reference may be feasible. Workers at Osaka University have reported a laser beam straightness reference that has a resolution of 3.5 nm, although tests were done only over a 200 mm length. LLNL has begun an investigation on the use of a directionally stabilized laser beam as a straightness measurement reference. The goal of the investigation is to provide a reference that is accurate to 25 nm (1 microinch) over a four meter distance. 3 refs., 2 figs.« less

Oculogravic illusion in response to straight-ahead acceleration of a CF-104 aircraft

NASA Technical Reports Server (NTRS)

Graybiel, A.; Jennings, G. L.; Johnson, W. H.; Money, K. E.; Malcolm, R. E.

1979-01-01

Experimental subjects wore goggles that restricted monocular vision to a luminous line fixed relative to the head, and they were exposed on one occasion to a straight-ahead acceleration of an aircraft and on another occasion to a tilting chair. The magnitude of change of direction of the resultant acceleration was the same on both occasions, but the perceived movement of the luminous line from the two stimuli was very different. In response to the aircraft stimulus, the oculogravic illusion was experienced and the luminous line was perceived as tilting relative to the subject, in response to the tilting chair stimulus, the line was perceived as remaining fixed relative to the subject. It was concluded that the oculogravic illusion, as experienced in the aircraft (and previously in centrifuges), is a true illusion and not merely a fact of physics.

Incidents between Straight-ahead Cyclists and Right-turning Motor Vehicles at Signalised Junctions.

PubMed

Buch, Thomas Skallebæk; Jensen, Søren Underlien

2017-08-01

Accidents between right-turning motor vehicles and straight-ahead cyclists are one of the most common accident types leading to cyclist injuries at signalised junctions in Denmark. A before-after safety evaluation of applying staggered stop lines in 189 arms at 123 signalised junctions is presented. The evaluation accounts for long-term accident trends and changes in motor vehicle traffic volumes. Applying staggered stop lines gives no decline in accidents between right-turning motor vehicles and straight-ahead cyclists. However, there is a statistical tendency to a decline of these right-turn accidents involving heavy vehicles. There are several questions about factors leading to right-turn accidents that cannot be answered by recorded accident data. A study of conflicting behaviour focuses on factors leading to conflicts. Video observations have been carried out in 10 arms at signalised junctions. A total of 45 situations with conflicting behaviour between right-turning motor vehicles and straight-ahead cyclists have been investigated and compared to a reference group of simultaneous arrivals. The relative risk is lowest when both parties stop on red before entering the junction. Upon simultaneous arrival of both parties at a green light, the relative risk is highest. Cyclists tend to have a higher relative risk of being involved in conflicts if they; a) ride through on yellow, b) have a time distance of at least 2seconds to other cyclists, c) wear a black jacket, and/or d) arrive at the junction at a speed of at least 25km/h. Much less can be said about the motor vehicles or their drivers on the basis of these video observations, but motor vehicles stopping in the cycle crossing in order to yield to pedestrians or cyclists have a higher relative risk of being involved in conflicts. Copyright © 2016 Elsevier Ltd. All rights reserved.

The hybrid reactor project based on the straight field line mirror concept

NASA Astrophysics Data System (ADS)

Ågren, O.; Noack, K.; Moiseenko, V. E.; Hagnestâl, A.; Källne, J.; Anglart, H.

2012-06-01

The straight field line mirror (SFLM) concept is aiming towards a steady-state compact fusion neutron source. Besides the possibility for steady state operation for a year or more, the geometry is chosen to avoid high loads on materials and plasma facing components. A comparatively small fusion hybrid device with "semi-poor" plasma confinement (with a low fusion Q factor) may be developed for industrial transmutation and energy production from spent nuclear fuel. This opportunity arises from a large fission to fusion energy multiplication ratio, Qr = Pfis/Pfus>>1. The upper bound on Qr is primarily determined by geometry and reactor safety. For the SFLM, the upper bound is Qr≈150, corresponding to a neutron multiplicity of keff=0.97. Power production in a mirror hybrid is predicted for a substantially lower electron temperature than the requirement Te≈10 keV for a fusion reactor. Power production in the SFLM seems possible with Q≈0.15, which is 10 times lower than typically anticipated for hybrids (and 100 times smaller than required for a fusion reactor). This relaxes plasma confinement demands, and broadens the range for use of plasmas with supra-thermal ions in hybrid reactors. The SFLM concept is based on a mirror machine stabilized by qudrupolar magnetic fields and large expander tanks beyond the confinement region. The purpose of the expander tanks is to distribute axial plasma loss flow over a sufficiently large area so that the receiving plates can withstand the heat. Plasma stability is not relying on a plasma flow into the expander regions. With a suppressed plasma flow into the expander tanks, a possibility arise for higher electron temperature. A brief presentation will be given on basic theory for the SFLM with plasma stability and electron temperature issues, RF heating computations with sloshing ion formation, neutron transport computations with reactor safety margins and material load estimates, magnetic coil designs as well as a discussion on

Evaluation of Bole Straightness in Cottonwood Using Visual Scores

Treesearch

D.T. Cooper; R.B. Ferguson

1981-01-01

Selection for straightness in natural stands of cottonwood can be effective in improving straightness of open-pollinated progeny. Straightness appears to be highly heritable, but it is subject to imprecise evaluation. This can be largely overcome by repeated application of an imprecise scoring system using a minimum of two views per tree separated by 90 degrees.

Straight talk new approaches in healthcare. The outpatient market: protect important market share.

PubMed

Broermann, Robert A; Kerner, Donald J; Walters, H Patrick; Hickman, Brett M

2003-10-27

Hospitals are facing competition from myriad freestanding players in the outpatient market. It's a fight hospitals can't afford to lose because they often use outpatient profits to cover losses in other service lines. Indeed about 60% of the average hospital's operating margin depends on outpatient revenues. In this session of Straight Talk, we examine how hospitals can build and finance outpatient services with physicians, increasing their competitiveness in increasingly competitive markets.

Min-cut segmentation of cursive handwriting in tabular documents

NASA Astrophysics Data System (ADS)

Davis, Brian L.; Barrett, William A.; Swingle, Scott D.

2015-01-01

Handwritten tabular documents, such as census, birth, death and marriage records, contain a wealth of information vital to genealogical and related research. Much work has been done in segmenting freeform handwriting, however, segmentation of cursive handwriting in tabular documents is still an unsolved problem. Tabular documents present unique segmentation challenges caused by handwriting overlapping cell-boundaries and other words, both horizontally and vertically, as "ascenders" and "descenders" overlap into adjacent cells. This paper presents a method for segmenting handwriting in tabular documents using a min-cut/max-flow algorithm on a graph formed from a distance map and connected components of handwriting. Specifically, we focus on line, word and first letter segmentation. Additionally, we include the angles of strokes of the handwriting as a third dimension to our graph to enable the resulting segments to share pixels of overlapping letters. Word segmentation accuracy is 89.5% evaluating lines of the data set used in the ICDAR2013 Handwriting Segmentation Contest. Accuracy is 92.6% for a specific application of segmenting first and last names from noisy census records. Accuracy for segmenting lines of names from noisy census records is 80.7%. The 3D graph cutting shows promise in segmenting overlapping letters, although highly convoluted or overlapping handwriting remains an ongoing challenge.

Faster embryonic segmentation through elevated Delta-Notch signalling

PubMed Central

Liao, Bo-Kai; Jörg, David J.; Oates, Andrew C.

2016-01-01

An important step in understanding biological rhythms is the control of period. A multicellular, rhythmic patterning system termed the segmentation clock is thought to govern the sequential production of the vertebrate embryo's body segments, the somites. Several genetic loss-of-function conditions, including the Delta-Notch intercellular signalling mutants, result in slower segmentation. Here, we generate DeltaD transgenic zebrafish lines with a range of copy numbers and correspondingly increased signalling levels, and observe faster segmentation. The highest-expressing line shows an altered oscillating gene expression wave pattern and shortened segmentation period, producing embryos with more, shorter body segments. Our results reveal surprising differences in how Notch signalling strength is quantitatively interpreted in different organ systems, and suggest a role for intercellular communication in regulating the output period of the segmentation clock by altering its spatial pattern. PMID:27302627

Computer aided solution for segmenting the neuron line in hippocampal microscope images

NASA Astrophysics Data System (ADS)

Albaidhani, Tahseen; Jassim, Sabah; Al-Assam, Hisham

2017-05-01

The brain Hippocampus component is known to be responsible for memory and spatial navigation. Its functionality depends on the status of different blood vessels within the Hippocampus and is severely impaired by Alzheimer's disease as a result blockage of increasing number of blood vessels by accumulation of amyloid-beta (Aβ) protein. Accurate counting of blood vessels within the Hippocampus of mice brain, from microscopic images, is an active research area for the understanding of Alzheimer's disease. Here, we report our work on automatic detection of the Region of Interest, i.e. the region in which blood vessels are located. This area typically falls between the hippocampus edge and the line of neurons within the Hippocampus. This paper proposes a new method to detect and exclude the neuron line to improve the accuracy of blood vessel counting because some neurons on it might lead to false positive cases as they look like blood vessels. Our proposed solution is based on using trainable segmentation approach with morphological operations, taking into account variation in colour, intensity values, and image texture. Experiments on a sufficient number of microscopy images of mouse brain demonstrate the effectiveness of the developed solution in preparation for blood vessels counting.

Comparison of structural and least-squares lines for estimating geologic relations

USGS Publications Warehouse

Williams, G.P.; Troutman, B.M.

1990-01-01

Two different goals in fitting straight lines to data are to estimate a "true" linear relation (physical law) and to predict values of the dependent variable with the smallest possible error. Regarding the first goal, a Monte Carlo study indicated that the structural-analysis (SA) method of fitting straight lines to data is superior to the ordinary least-squares (OLS) method for estimating "true" straight-line relations. Number of data points, slope and intercept of the true relation, and variances of the errors associated with the independent (X) and dependent (Y) variables influence the degree of agreement. For example, differences between the two line-fitting methods decrease as error in X becomes small relative to error in Y. Regarding the second goal-predicting the dependent variable-OLS is better than SA. Again, the difference diminishes as X takes on less error relative to Y. With respect to estimation of slope and intercept and prediction of Y, agreement between Monte Carlo results and large-sample theory was very good for sample sizes of 100, and fair to good for sample sizes of 20. The procedures and error measures are illustrated with two geologic examples. ?? 1990 International Association for Mathematical Geology.

Straight eye for the gay guy: composing queerness.

PubMed

Alexander, Jonathan

2010-01-01

Drawing on the work of Didier Eribon and his theorization of the construction of gay male subjectivity, this article examines different "texts," broadly defined, that grapple specifically with straight men attempting to represent male homosexuality: Norman Mailer's essay, "The Homosexual Villain"; the Bravo reality television series Boy Meets Boy, and Michael Griffith's short story, "Hooper Gets a Perm." These texts represent attempts by straight authors to grapple with queer experience in ways that move the imagination of queers beyond simple stereotypes or uncritical explorations of the sexual "other." In the process of examining these texts, the following questions are addressed: What happens when a straight man attempts to represent a gay man? Does he "get it right," and is such a question even useful? More specifically, what is the value in having straights imagine queerness? Is such an imagining possible? Is such desirable? And, if so, what are the contours of such an imagining-as well as its possibilities and limitations, pedagogically, personally, and politically? Ultimately, I contend that the straight imagining of queerness offers rich potential for mutual understanding; furthermore, attempting to understand what goes into the making of those representations tells us much about how queerness circulates in our culture as a subject, a figure of discussion, contention, and representation.

Technical design and system implementation of region-line primitive association framework

NASA Astrophysics Data System (ADS)

Wang, Min; Xing, Jinjin; Wang, Jie; Lv, Guonian

2017-08-01

Apart from regions, image edge lines are an important information source, and they deserve more attention in object-based image analysis (OBIA) than they currently receive. In the region-line primitive association framework (RLPAF), we promote straight-edge lines as line primitives to achieve powerful OBIAs. Along with regions, straight lines become basic units for subsequent extraction and analysis of OBIA features. This study develops a new software system called remote-sensing knowledge finder (RSFinder) to implement RLPAF for engineering application purposes. This paper introduces the extended technical framework, a comprehensively designed feature set, key technology, and software implementation. To our knowledge, RSFinder is the world's first OBIA system based on two types of primitives, namely, regions and lines. It is fundamentally different from other well-known region-only-based OBIA systems, such as eCogntion and ENVI feature extraction module. This paper has important reference values for the development of similarly structured OBIA systems and line-involved extraction algorithms of remote sensing information.

7 CFR 29.6128 - Straight Stripped (X Group).

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Straight Stripped (X Group). 29.6128 Section 29.6128 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards... REGULATIONS TOBACCO INSPECTION Standards Grades § 29.6128 Straight Stripped (X Group). This group consists of...

7 CFR 29.6128 - Straight Stripped (X Group).

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 2 2012-01-01 2012-01-01 false Straight Stripped (X Group). 29.6128 Section 29.6128 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards... REGULATIONS TOBACCO INSPECTION Standards Grades § 29.6128 Straight Stripped (X Group). This group consists of...

7 CFR 29.6128 - Straight Stripped (X Group).

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Straight Stripped (X Group). 29.6128 Section 29.6128 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards... REGULATIONS TOBACCO INSPECTION Standards Grades § 29.6128 Straight Stripped (X Group). This group consists of...

7 CFR 29.6128 - Straight Stripped (X Group).

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 2 2014-01-01 2014-01-01 false Straight Stripped (X Group). 29.6128 Section 29.6128 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards... REGULATIONS TOBACCO INSPECTION Standards Grades § 29.6128 Straight Stripped (X Group). This group consists of...

7 CFR 29.6128 - Straight Stripped (X Group).

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 2 2013-01-01 2013-01-01 false Straight Stripped (X Group). 29.6128 Section 29.6128 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards... REGULATIONS TOBACCO INSPECTION Standards Grades § 29.6128 Straight Stripped (X Group). This group consists of...

Intestinal permeability enhancement of levothyroxine sodium by straight chain fatty acids studied in MDCK epithelial cell line.

PubMed

Pabla, Dimple; Akhlaghi, Fatemeh; Zia, Hossein

2010-08-11

Levothyroxine sodium (T4), administered orally, is used for the treatment of hypothyroidism. T4 is a narrow therapeutic index drug with highly variable bioavailability (40-80%). The purpose of the present study was to increase the transepithelial transport of T4 using straight chain fatty acids across Madin-Darby Canine kidney (MDCK) cell line. Capric acid (C10), lauric acid (C12) and oleic acid (C18) were studied in molar ratios of 1:0.5, 1:1, 1:2 and 1:3 (T4:fatty acid). Transport of the hydrophilic marker, Lucifer yellow, was also studied. All three fatty acids proved to significantly increase T4 transport and the order of enhancement was to the effect of C12 approximately C18>C10. This Increase in transport was accompanied by reductions in transepithelial electrical resistance (TEER) values, which indicates an opening of tight junctions. Cytotoxic effects of the fatty acids were evaluated by TEER measurements, lactate dehydrogenase release, percent viability and propidium iodide staining of the cells. At the lower molar concentrations of 1:1, the fatty acids did not show any toxicity. However, C12 and C18 when added, to T4:fatty acid molar ratio of 1:2 and 1:3, respectively showed severe toxicity with irreversible damage to the cells. Hence, addition of fatty acids to T4 formulations at low concentrations can significantly improve intestinal permeability of T4 without any toxicity potentially leading to improved bioavailability. 2010 Elsevier B.V. All rights reserved.

Illusory bending of a rigidly moving line segment: effects of image motion and smooth pursuit eye movements.

PubMed

Thaler, Lore; Todd, James T; Spering, Miriam; Gegenfurtner, Karl R

2007-04-20

Four experiments in which observers judged the apparent "rubberiness" of a line segment undergoing different types of rigid motion are reported. The results reveal that observers perceive illusory bending when the motion involves certain combinations of translational and rotational components and that the illusion is maximized when these components are presented at a frequency of approximately 3 Hz with a relative phase angle of approximately 120 degrees . Smooth pursuit eye movements can amplify or attenuate the illusion, which is consistent with other results reported in the literature that show effects of eye movements on perceived image motion. The illusion is unaffected by background motion that is in counterphase with the motion of the line segment but is significantly attenuated by background motion that is in-phase. This is consistent with the idea that human observers integrate motion signals within a local frame of reference, and it provides strong evidence that visual persistency cannot be the sole cause of the illusion as was suggested by J. R. Pomerantz (1983). An analysis of the motion patterns suggests that the illusory bending motion may be due to an inability of observers to accurately track the motions of features whose image displacements undergo rapid simultaneous changes in both space and time. A measure of these changes is presented, which is highly correlated with observers' numerical ratings of rubberiness.

Electromagnetic scattering by a straight thin wire

NASA Technical Reports Server (NTRS)

Shamansky, Harry T.; Dominek, Allen K.; Peters, Leon, Jr.

1989-01-01

The traveling-wave energy, which multiply diffracts on a straight thin wire, is represented as a sum of terms, each with a distinct physical meaning, that can be individually examined in the time domain. Expressions for each scattering mechanism on a straight thin wire are cast in the form of four basic electromagnetic wave concepts: diffraction, attachment, launch, and reflection. Using the basic mechanisms from P. Ya. Ufimtsev (1962), each of the scattering mechanisms is included into the total scattered field for the straight thin wire. Scattering as a function of angle and frequency is then compared to the moment-method solution. These analytic expressions are then extended to a lossy wire with a simple approximate modification using the propagation velocity on the wire as derived from the Sommerfeld wave on a straight lossy wire. Both the perfectly conducting and lossy wire solutions are compared to moment-method results, and excellent agreement is found. As is common with asymptotic solutions, when the electrical length of wire is smaller than 0.2 lambda the results lose accuracy. The expressions modified to approximate the scattering for the lossy thin wire yield excellent agreement even for lossy wires where the wire radius is on the order of skin depth.

Microwave focusators

NASA Astrophysics Data System (ADS)

Vinogradov, E. A.; Gridin, S. A.; Golovanov, V. I.; Danilenko, A. A.; Bulatov, E. D.

1989-01-01

A system capable of focusing monochromatic microwave radiation with a spherical or planar wavefront into a straight line segment is designed. The system consists of zone elements made with numerically controlled machine tools. The study of the image obtained revealed that the width of the formed local segment is close to the diffraction limit.

46 CFR Appendix A to Part 45 - Load Line Certificate Form

Code of Federal Regulations, 2011 CFR

2011-10-01

... registry Type of Ship: TYPE “A” TYPE “B” TYPE “B” with increased freeboard freeboard from deck line Midsummer MS Summer S Intermediate I Winter W load line above S Upper edge of line through center of diamond... salt water of the St. Lawrence River west of a straight line from Cap de Rosiers to West Point...

Hydrodynamic shrinkage of liquid CO2 Taylor drops in a straight microchannel

NASA Astrophysics Data System (ADS)

Qin, Ning; Wen, John Z.; Ren, Carolyn L.

2018-03-01

Hydrodynamic shrinkage of liquid CO2 drops in water under a Taylor flow regime is studied using a straight microchannel (length/width ~100). A general form of a mathematical model of the solvent-side mass transfer coefficient (k s) is developed first. Based on formulations of the surface area (A) and the volume (V) of a general Taylor drop in a rectangular microchannel, a specific form of k s is derived. Drop length and speed are experimentally measured at three specified positions of the straight channel, namely, immediately after drop generation (position 1), the midpoint of the channel (position 2) and the end of the channel (position 3). The reductions of drop length (L x , x  =  1, 2, 3) from position 1 to 2 and down to 3 are used to quantify the drop shrinkage. Using the specific model, k s is calculated mainly based on L x and drop flowing time (t). Results show that smaller CO2 drops produced by lower flow rate ratios ({{Q}LC{{O2}}}/{{Q}{{H2}O}} ) are generally characterized by higher (nearly three times) k s and Sherwood numbers than those produced by higher {{Q}LC{{O2}}}/{{Q}{{H2}O}} , which is essentially attributed to the larger effective portion of the smaller drop contributing in the mass transfer under same levels of the flowing time and the surface-to-volume ratio (~104 m-1) of all drops. Based on calculated pressure drops of the segmented flow in microchannel, the Peng-Robinson equation of state and initial pressures of drops at the T-junction in experiments, overall pressure drop (ΔP t) in the straight channel as well as the resulted drop volume change are quantified. ΔP t from position 1-3 is by average 3.175 kPa with a ~1.6% standard error, which only leads to relative drop volume changes of 0.3‰ to 0.52‰.

Homeologous Recombination in Solanum lycopersicoides Introgression Lines of Cultivated Tomato

PubMed Central

Canady, Michael A.; Ji, Yuanfu; Chetelat, Roger T.

2006-01-01

A library of “introgression lines” containing Solanum lycopersicoides chromosome segments in the genetic background of cultivated tomato (Lycopersicon esculentum) was used to study factors affecting homeologous recombination. Recombination rates were estimated in progeny of 43 heterozygous introgressions and whole-chromosome substitution lines, together representing 11 of the 12 tomato chromosomes. Recombination within homeologous segments was reduced to as little as 0–10% of expected frequencies. Relative recombination rates were positively correlated with the length of introgressed segments on the tomato map. The highest recombination (up to 40–50% of normal) was observed in long introgressions or substitution lines. Double-introgression lines containing two homeologous segments on opposite chromosome arms were synthesized to increase their combined length. Recombination was higher in the double than in the single segment lines, despite a preference for crossovers in the region of homology between segments. A greater increase in homeologous recombination was obtained by crossing the S. lycopersicoides introgression lines to L. pennellii—a phylogenetically intermediate species—or to L. esculentum lines containing single L. pennellii segments on the same chromosome. Recombination rates were highest in regions of overlap between S. lycopersicoides and L. pennellii segments. The potential application of these results to breeding with introgression lines is discussed. PMID:17057228

Evolution of turbulence characteristics from straight to curved pipes

NASA Astrophysics Data System (ADS)

El Khoury, George K.; Noorani, Azad; Schlatter, Philipp; Fischer, Paul F.

2012-11-01

Large-scale direct numerical simulations are performed to study turbulent flow in straight and bent pipes at four different Reynolds numbers: Reb = 5300 , 11700 (bent and straight) and 19000 and 37700 (only straight). We consider a pipe of radius R and axial length 25 R with curvature parameter κ taken to be 0 , 0 . 01 and 0 . 1 for zero, mild and strong curvatures, respectively. The code used is Nek5000 based on the spectral element method. In the straight configuration, the obtained DNS data is carefully checked against other recent simulations, highlighting minute differences between the available data. Owing to a centrifugal instability mechanism, the flow in bent pipe (κ ≠ 0) develops counter-rotating vortices, so-called Dean vortices. The presence of the secondary motion thus induces substantial asymmetries both in the mean flow and turbulence characteristics for the bent pipe. These asymmetries tend to damp turbulence along the inner side and correspondingly enhance it along the upper side. The results are validated with recent experiments, and we could confirm the peculiar behaviour of the friction factor for specific curvatures and Re , leading to a lower friction in curved pipes than in straight pipes for the same mass flux.

A perceptive method for handwritten text segmentation

NASA Astrophysics Data System (ADS)

Lemaitre, Aurélie; Camillerapp, Jean; Coüasnon, Bertrand

2011-01-01

This paper presents a new method to address the problem of handwritten text segmentation into text lines and words. Thus, we propose a method based on the cooperation among points of view that enables the localization of the text lines in a low resolution image, and then to associate the pixels at a higher level of resolution. Thanks to the combination of levels of vision, we can detect overlapping characters and re-segment the connected components during the analysis. Then, we propose a segmentation of lines into words based on the cooperation among digital data and symbolic knowledge. The digital data are obtained from distances inside a Delaunay graph, which gives a precise distance between connected components, at the pixel level. We introduce structural rules in order to take into account some generic knowledge about the organization of a text page. This cooperation among information gives a bigger power of expression and ensures the global coherence of the recognition. We validate this work using the metrics and the database proposed for the segmentation contest of ICDAR 2009. Thus, we show that our method obtains very interesting results, compared to the other methods of the literature. More precisely, we are able to deal with slope and curvature, overlapping text lines and varied kinds of writings, which are the main difficulties met by the other methods.

An argument for the use of multiple segment stents in curved arteries.

PubMed

Kasiri, Saeid; Kelly, Daniel J

2011-08-01

Stenting of curved arteries is generally perceived to be more challenging than straight vessels. Conceptually implanting multiple shorter stents rather than a single longer stent into such a curved artery represents a promising concept, but little is known about the impact of such an approach. The objective of this study is to evaluate the effectiveness of using a multiple segment stent rather than a single long stent to dilate a curved artery using the finite element method. A double segment stent (DSS) and a single segment stent (SSS) were modeled. The stents were compared when expanded into a model of a curved artery. The model predicts that the DSS provides higher flexibility, more conformity, and lower recoil in comparison to the SSS. The volume of arterial tissue experiencing high levels of stress due to stent implantation is also reduced for the DSS. It is suggested that a multiple segment stenting system is a potential solution to the problem of higher rates of in-stent restenosis in curved arteries and mechanically challenging environments.

User-guided segmentation for volumetric retinal optical coherence tomography images

PubMed Central

Yin, Xin; Chao, Jennifer R.; Wang, Ruikang K.

2014-01-01

Abstract. Despite the existence of automatic segmentation techniques, trained graders still rely on manual segmentation to provide retinal layers and features from clinical optical coherence tomography (OCT) images for accurate measurements. To bridge the gap between this time-consuming need of manual segmentation and currently available automatic segmentation techniques, this paper proposes a user-guided segmentation method to perform the segmentation of retinal layers and features in OCT images. With this method, by interactively navigating three-dimensional (3-D) OCT images, the user first manually defines user-defined (or sketched) lines at regions where the retinal layers appear very irregular for which the automatic segmentation method often fails to provide satisfactory results. The algorithm is then guided by these sketched lines to trace the entire 3-D retinal layer and anatomical features by the use of novel layer and edge detectors that are based on robust likelihood estimation. The layer and edge boundaries are finally obtained to achieve segmentation. Segmentation of retinal layers in mouse and human OCT images demonstrates the reliability and efficiency of the proposed user-guided segmentation method. PMID:25147962

User-guided segmentation for volumetric retinal optical coherence tomography images.

PubMed

Yin, Xin; Chao, Jennifer R; Wang, Ruikang K

2014-08-01

Despite the existence of automatic segmentation techniques, trained graders still rely on manual segmentation to provide retinal layers and features from clinical optical coherence tomography (OCT) images for accurate measurements. To bridge the gap between this time-consuming need of manual segmentation and currently available automatic segmentation techniques, this paper proposes a user-guided segmentation method to perform the segmentation of retinal layers and features in OCT images. With this method, by interactively navigating three-dimensional (3-D) OCT images, the user first manually defines user-defined (or sketched) lines at regions where the retinal layers appear very irregular for which the automatic segmentation method often fails to provide satisfactory results. The algorithm is then guided by these sketched lines to trace the entire 3-D retinal layer and anatomical features by the use of novel layer and edge detectors that are based on robust likelihood estimation. The layer and edge boundaries are finally obtained to achieve segmentation. Segmentation of retinal layers in mouse and human OCT images demonstrates the reliability and efficiency of the proposed user-guided segmentation method.

Straight Talk For Good Health | NIH MedlinePlus the Magazine

MedlinePlus

... Communication Straight Talk For Good Health Past Issues / Summer 2015 Table of Contents Straight talk with your ... with your Doctor nihseniorhealth.gov/talkingwithyourdoctor/toc.html Summer 2015 Issue: Volume 10 Number 2 Page 14- ...

Rapidity evolution of Wilson lines at the next-to-leading order

DOE Office of Scientific and Technical Information (OSTI.GOV)

Balitsky, Ian; Chirilli, Giovanni

2013-12-01

At high energies particles move very fast so the proper degrees of freedom for the fast gluons moving along the straight lines are Wilson-line operators - infinite gauge factors ordered along the line. In the framework of operator expansion in Wilson lines the energy dependence of the amplitudes is determined by the rapidity evolution of Wilson lines. We present the next-to-leading order hierarchy of the evolution equations for Wilson-line operators.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ruland, Robert

The Visible-Infrared SASE Amplifier (VISA) undulator consists of four 99cm long segments. Each undulator segment is set up on a pulsed-wire bench, to characterize the magnetic properties and to locate the magnetic axis of the FODO array. Subsequently, the location of the magnetic axis, as defined by the wire, is referenced to tooling balls on each magnet segment by means of a straightness interferometer. After installation in the vacuum chamber, the four magnet segments are aligned with respect to themselves and globally to the beam line reference laser. A specially designed alignment fixture is used to mount one straightness interferometermore » each in the horizontal and vertical plane of the beam. The goal of these procedures is to keep the combined rms trajectory error, due to magnetic and alignment errors, to 50{micro}m.« less

Line intersect sampling: Ell-shaped transects and multiple intersections

Treesearch

Timothy G. Gregoire; Harry T. Valentine

2003-01-01

The probability of selecting a population element under line intersect sampling depends on the width of the particle in the direction perpendicular to the transect, as is well known. The consequence of this when using ell-shaped transects rather than straight-line transects are explicated, and modifications that preserve design-unbiasedness of Kaiser's (1983)...

Sequence Segmentation with changeptGUI.

PubMed

Tasker, Edward; Keith, Jonathan M

2017-01-01

Many biological sequences have a segmental structure that can provide valuable clues to their content, structure, and function. The program changept is a tool for investigating the segmental structure of a sequence, and can also be applied to multiple sequences in parallel to identify a common segmental structure, thus providing a method for integrating multiple data types to identify functional elements in genomes. In the previous edition of this book, a command line interface for changept is described. Here we present a graphical user interface for this package, called changeptGUI. This interface also includes tools for pre- and post-processing of data and results to facilitate investigation of the number and characteristics of segment classes.

Preferences of AP position of the straight Caucasian facial profile.

PubMed

Mees, Steven; Jiménez Bellinga, Raúl; Mommaerts, Maurice Y; De Pauw, Guy A M

2013-12-01

Several investigators have compared the perception of profile attractiveness between professional and non-professional people, different groups of clinicians, and different ethnic groups. Our aim was to study preferences for facial protrusion in the lateral view for a straight Class I profile and to study the influence of gender, age, sex preference, and profession. Portrait images of one male and one female model with a Class I occlusal relationship were warped into nine different antero-posterior positions. An internet site was established to reach as many people as possible, and a request was sent by email to participate in a scientific experiment. Finally, 1707 Caucasion assessors could be grouped. The preferred male profile is the straight full ante profile. For a feminine facial profile, the straight average and the straight 2/3 ante profiles were perceived as the most attractive. Surgeons tended to give significantly higher scores to attractive (ante) profiles, which correlated strongly with scores of the orthodontists. Whenever possible with combined orthodontic/surgery treatment, straight ante profiles should be aimed for. Copyright © 2013 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

A real-time visual inspection method of fastening bolts in freight car operation

NASA Astrophysics Data System (ADS)

Nan, Guo; Yao, JunEn

2015-10-01

A real-time inspection of the key components is necessary for ensuring safe operation of freight car. While traditional inspection depends on the trained human inspectors, which is time-consuming and lower efficient. With the development of machine vision, vision-based inspection methods get more railway on-spot applications. The cross rod end fastening bolts are important components on both sides of the train body that fixing locking plates together with the freight car main structure. In our experiment, we get the images containing fastening bolt components, and accurately locate the locking plate position using a linear Support Vector Machine (SVM) locating model trained with Histograms of Oriented Gradients (HOG) features. Then we extract the straight line segment using the Line Segment Detector (LSD) and encoding them in a range, which constitute a straight line segment dataset. Lastly we determine the locking plate's working state by the linear pattern. The experiment result shows that the localization accurate rate is over 99%, the fault detection rate is over 95%, and the module implementation time is 2f/s. The overall performance can completely meet the practical railway safety assurance application.

A hybrid algorithm for the segmentation of books in libraries

NASA Astrophysics Data System (ADS)

Hu, Zilong; Tang, Jinshan; Lei, Liang

2016-05-01

This paper proposes an algorithm for book segmentation based on bookshelves images. The algorithm can be separated into three parts. The first part is pre-processing, aiming at eliminating or decreasing the effect of image noise and illumination conditions. The second part is near-horizontal line detection based on Canny edge detector, and separating a bookshelves image into multiple sub-images so that each sub-image contains an individual shelf. The last part is book segmentation. In each shelf image, near-vertical line is detected, and obtained lines are used for book segmentation. The proposed algorithm was tested with the bookshelf images taken from OPIE library in MTU, and the experimental results demonstrate good performance.

Paleomagnetic evidence for counterclockwise rotation of the Dofan magmatic segment, Main Ethiopian Rift

NASA Astrophysics Data System (ADS)

Nugsse, Kahsay; Muluneh, Ameha A.; Kidane, Tesfaye

2018-04-01

Twenty-six paleomagnetic sites in basalt and trachyte flows and ignimbrite deposits sampled in the Dofan magmatic segment, Main Ethiopian Rift (MER). From each site, 6 to 8 core samples were collected. The samples were then cut into 200 standard specimens and their Natural Remanent Magnetization (NRM) directions were measured using a JR6A spinner magnetometer. Most specimens were subjected to stepwise alternating field (AF) and at least one specimen per site to thermal (TH) demagnetization. The directional analysis of these individual specimens revealed either one or two components of NRM. Where two components are present, the first is isolated below a temperature of 300 °C or AF field below 20 mT; the second is isolated above those steps and mostly defined straight lines directed towards the origin and are interpreted as the Characteristic Remanent Magnetization (ChRM) acquired during cooling. Rock magnetic experiments on representative specimens indicate that the dominant magnetic minerals are titanium poor titanomagnetite and in few cases titanohematites. The overall mean directions calculated for the 23 sites of Dofan is Dec = 354.1°, Inc. = +11.6° (N = 23, K = 35.1, α95 = 5.2°). When these values are compared with the 1.5 Ma expected mean geomagnetic dipole reference field directions Dec = 1.0°, Inc. = +16.4° (N = 32, K = 105.6, α95 = 2.3°), obtained from African Apparent Polar Wander Path Curve; a difference in declination ΔD = -6.9° ± 4.7° and inclination ΔI = +4.8° ± 5.5° are determined. The declination difference is interpreted as a very slight counterclockwise rotation about vertical axis of the Dofan magmatic segment and the result is consistent with previous paleomagnetic reports and analogue modeling in Fentale magmatic segment.

Autonomous Unmanned Aerial Vehicle Rendezvous for Automated Aerial Refueling

DTIC Science & Technology

2007-03-01

represents a straight line segment. It can be seen that there are ten possible combinations of arcs and line segments (RSR, RSL, LSR, LSL, LRL, RLR , SLR...SRL, RLS, and LRS). However, L. E. Dubins proved that only these six sequences are possibly optimal: RSR, RSL, LSR, LSL, LRL, and RLR [Dubins 1957...From Figure 2-5 and Figure 2-6, it can be seen that the last two cases, RLR and LRL can only be optimal when the initial point and the terminal

Robust visual object tracking with interleaved segmentation

NASA Astrophysics Data System (ADS)

Abel, Peter; Kieritz, Hilke; Becker, Stefan; Arens, Michael

2017-10-01

In this paper we present a new approach for tracking non-rigid, deformable objects by means of merging an on-line boosting-based tracker and a fast foreground background segmentation. We extend an on-line boosting- based tracker, which uses axes-aligned bounding boxes with fixed aspect-ratio as tracking states. By constructing a confidence map from the on-line boosting-based tracker and unifying this map with a confidence map, which is obtained from a foreground background segmentation algorithm, we build a superior confidence map. For constructing a rough confidence map of a new frame based on on-line boosting, we employ the responses of the strong classifier as well as the single weak classifier responses that were built before during the updating step. This confidence map provides a rough estimation of the object's position and dimension. In order to refine this confidence map, we build a fine, pixel-wisely segmented confidence map and merge both maps together. Our segmentation method is color-histogram-based and provides a fine and fast image segmentation. By means of back-projection and the Bayes' rule, we obtain a confidence value for every pixel. The rough and the fine confidence maps are merged together by building an adaptively weighted sum of both maps. The weights are obtained by utilizing the variances of both confidence maps. Further, we apply morphological operators in the merged confidence map in order to reduce the noise. In the resulting map we estimate the object localization and dimension via continuous adaptive mean shift. Our approach provides a rotated rectangle as tracking states, which enables a more precise description of non-rigid, deformable objects than axes-aligned bounding boxes. We evaluate our tracker on the visual object tracking (VOT) benchmark dataset 2016.

An unexplained three-dimensional percept emerging from a bundle of lines.

PubMed

Altschuler, Eric L; Huang, Abigail E; Kim, Hee J; Battaglini, Luca; Roncato, Sergio

2017-10-01

Perceptual grouping has been extensively studied, but some areas are still unexplored-in particular, the figural organizations that emerge when bundles of intersecting lines are drawn. Here, we will describe some figural organizations that emerge after the superimposition of bundles of lines forming the profile of regular triangular waves. By manipulating the lines' jaggedness and junction geometry (regular or irregular X junction) we could generate the following organizations: (a) a grid, or a figural configuration in which both the lines and closed contours are perceived, (b) a figure-ground organization composed of figures separated by portions of the background, and (c) a corrugated surface appearing as a multifaceted polyhedral shell crossed by ridges and valleys. An experiment was conducted with the aim at testing the role of the good-continuation and closure Gestalt factors. Good continuation prevails when the lines are straight or close to straightness, but its role is questionable in the appearance of a corrugated surface. This perceptual organization occurs despite the violation of the good-continuation rule and consists of a structure of such complexity so as to challenge algorithms of computer vision and stimulate a deeper understanding of the perceptual interpretation of groups of lines.

Stigma and Stigma by Association in Perceptions of Straight Allies

ERIC Educational Resources Information Center

Goldstein, Susan B.

2017-01-01

As evidence builds for straight allies' contributions to battling sexual prejudice, barriers to assuming this role must be identified and dismantled. This study investigated stigma and stigma by association in perceptions of straight allies in a college population. Adjective rating items were completed by 505 participants who identified as…

Transmission Line Ampacity Improvements of AltaLink Wind Plant Overhead Tie-Lines Using Weather-Based Dynamic Line Rating

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhattarai, Bishnu P.; Gentle, Jake P.; Hill, Porter

Abstract—Overhead transmission lines (TLs) are conventionally given seasonal ratings based on conservative environmental assumptions. Such an approach often results in underutilization of the line ampacity as the worst conditions prevail only for a short period over a year/season. We presents dynamic line rating (DLR) as an enabling smart grid technology that adaptively computes ratings of TLs based on local weather conditions to utilize additional headroom of existing lines. In particular, general line ampacity state solver utilizes measured weather data for computing the real-time thermal rating of the TLs. The performance of the presented method is demonstrated from a field studymore » of DLR technology implementation on four TL segments at AltaLink, Canada. The performance is evaluated and quantified by comparing the existing static and proposed dynamic line ratings, and the potential benefits of DLR for enhanced transmission assets utilization. For the given line segments, the proposed DLR results in real-time ratings above the seasonal static ratings for most of the time; up to 95.1% of the time, with a mean increase of 72% over static rating.« less

Charge density on thin straight wire, revisited

NASA Astrophysics Data System (ADS)

Jackson, J. D.

2000-09-01

The question of the equilibrium linear charge density on a charged straight conducting "wire" of finite length as its cross-sectional dimension becomes vanishingly small relative to the length is revisited in our didactic presentation. We first consider the wire as the limit of a prolate spheroidal conductor with semi-minor axis a and semi-major axis c when a/c<<1. We then treat an azimuthally symmetric straight conductor of length 2c and variable radius r(z) whose scale is defined by a parameter a. A procedure is developed to find the linear charge density λ(z) as an expansion in powers of 1/Λ, where Λ≡ln(4c2/a2), beginning with a uniform line charge density λ0. We show, for this rather general wire, that in the limit Λ>>1 the linear charge density becomes essentially uniform, but that the tiny nonuniformity (of order 1/Λ) is sufficient to produce a tangential electric field (of order Λ0) that cancels the zeroth-order field that naively seems to belie equilibrium. We specialize to a right circular cylinder and obtain the linear charge density explicitly, correct to order 1/Λ2 inclusive, and also the capacitance of a long isolated charged cylinder, a result anticipated in the published literature 37 years ago. The results for the cylinder are compared with published numerical computations. The second-order correction to the charge density is calculated numerically for a sampling of other shapes to show that the details of the distribution for finite 1/Λ vary with the shape, even though density becomes constant in the limit Λ→∞. We give a second method of finding the charge distribution on the cylinder, one that approximates the charge density by a finite polynomial in z2 and requires the solution of a coupled set of linear algebraic equations. Perhaps the most striking general observation is that the approach to uniformity as a/c→0 is extremely slow.

21 CFR 70.20 - Packaging requirements for straight colors (other than hair dyes).

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 1 2013-04-01 2013-04-01 false Packaging requirements for straight colors (other than hair dyes). 70.20 Section 70.20 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH... straight colors (other than hair dyes). Straight colors shall be packaged in containers which prevent...

21 CFR 70.20 - Packaging requirements for straight colors (other than hair dyes).

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 1 2011-04-01 2011-04-01 false Packaging requirements for straight colors (other than hair dyes). 70.20 Section 70.20 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH... straight colors (other than hair dyes). Straight colors shall be packaged in containers which prevent...

21 CFR 70.20 - Packaging requirements for straight colors (other than hair dyes).

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 1 2014-04-01 2014-04-01 false Packaging requirements for straight colors (other than hair dyes). 70.20 Section 70.20 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH... straight colors (other than hair dyes). Straight colors shall be packaged in containers which prevent...

21 CFR 70.20 - Packaging requirements for straight colors (other than hair dyes).

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 1 2012-04-01 2012-04-01 false Packaging requirements for straight colors (other than hair dyes). 70.20 Section 70.20 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH... straight colors (other than hair dyes). Straight colors shall be packaged in containers which prevent...

Active versus Passive Proprioceptive Straight-Ahead Pointing in Normal Subjects

ERIC Educational Resources Information Center

Chokron, Sylvie; Colliot, Pascale; Atzeni, Thierry; Bartolomeo, Paolo; Ohlmann, Theophile

2004-01-01

Eighty blindfolded healthy female subjects participated in an active and a passive straight-ahead pointing task to study the estimation of the subjective sagittal middle in the presence or absence of an active haptic exploration. Subjects were to point straight-ahead with their left or right index finger starting from different right- or…

Nazca Lines, Peru

NASA Image and Video Library

2017-12-08

Acquisition Date: November 10, 2002 In the desert of southwest Peru, between the Andes Mountains and the Peruvian coast, lies a plateau with huge geometric patterns and spirals, animal figures including a monkey, a spider, and an 'owl man,' and thousands of perfectly straight lines. The last of these was drawn about a thousand years ago. Known as the Nazca lines, the drawings have mystified scientists since they were first discovered in the 1920s. Pictured here is all that can be seen of these lines by Landsat 7's 15 meter pan band, which has been used to sharpen the 30 meter Bands 3, 2, and 1. Credit: NASA/GSFC/Landsat/USGS To learn more about Landsat and to see the orginal high res file go to: landsat.usgs.gov/gallery_view.php?category=greenflag&...

Straight talk. New approaches in healthcare.

PubMed

Lanier, Jack; Loudermilk, Kerry; Skogsbergh, Jim; Clark, Reatha; Friz, Robert; Lopez, Fawn

2005-11-07

Not-for-profit health systems are under the public microscope. Sen. Charles Grassley, (D-Iowa) chairman of the Senate Finance Committee, has been critical of the charity care and billing practices of not-for-profit health systems, and vows to introduce legislation to correct abuses throughout the tax-exempt sector. The House has studied the issue as well. Not-for-profit health systems also have been accused in hundreds of lawsuits of overcharging uninsured patients and aggressively pursuing debt collection. In this installment of Straight Talk, we explore the issues surrounding tax-exempt status and how health systems should publicize their charitable work. Modern Healthcare and PricewaterhouseCoopers present Straight Talk. The session on charity care and tax-exempt status was held on October 4, 2005 at Modern Healthcare's Chicago headquarters. Fawn Lopez, publisher of Modern Healthcare, was the moderator.

Line plus arc source trajectories and their R-line coverage for long-object cone-beam imaging with a C-arm system

NASA Astrophysics Data System (ADS)

Yu, Zhicong; Wunderlich, Adam; Dennerlein, Frank; Lauritsch, Günter; Noo, Frédéric

2011-06-01

Cone-beam imaging with C-arm systems has become a valuable tool in interventional radiology. Currently, a simple circular trajectory is used, but future applications should use more sophisticated source trajectories, not only to avoid cone-beam artifacts but also to allow extended volume imaging. One attractive strategy to achieve these two goals is to use a source trajectory that consists of two parallel circular arcs connected by a line segment, possibly with repetition. In this work, we address the question of R-line coverage for such a trajectory. More specifically, we examine to what extent R-lines for such a trajectory cover a central cylindrical region of interest (ROI). An R-line is a line segment connecting any two points on the source trajectory. Knowledge of R-line coverage is crucial because a general theory for theoretically exact and stable image reconstruction from axially truncated data is only known for the points in the scanned object that lie on R-lines. Our analysis starts by examining the R-line coverage for the elemental trajectories consisting of (i) two parallel circular arcs and (ii) a circular arc connected orthogonally to a line segment. Next, we utilize our understanding of the R-lines for the aforementioned elemental trajectories to determine the R-line coverage for the trajectory consisting of two parallel circular arcs connected by a tightly fit line segment. For this trajectory, we find that the R-line coverage is insufficient to completely cover any central ROI. Because extension of the line segment beyond the circular arcs helps to increase the R-line coverage, we subsequently propose a trajectory composed of two parallel circular arcs connected by an extended line. We show that the R-lines for this trajectory can fully cover a central ROI if the line extension is long enough. Our presentation includes a formula for the minimum line extension needed to achieve full R-line coverage of an ROI with a specified size, and also includes

Passive moment about the hip in straight leg raising.

PubMed

Lee, R Y; Munn, J

2000-06-01

The purpose of this examine is to study the load-deformation characteristics of the hip in straight leg raising. An experimental study in which passive moment about the hip was determined as a function of hip angle. Straight leg raising is widely employed in clinical examination, and there is little information on its mechanical characteristics. Fourteen healthy volunteers were recruited for this study. Three trials of straight leg raise tests were performed while subjects lay supine on a plinth that was fitted with load cells. An electrogoniometer was employed to measure hip flexion during the test. Resistive moment at the hip was determined using a dynamic biomechanical model. The present experimental method was shown to be highly reliable. The moment-angle curves of all subjects were shown to follow an exponential function. Stiffness and strain energy of posterior hip tissues could be derived from the moment-angle curves. Evaluation of such elastic properties is clinically important as they may be altered with injuries of the tissues. Clinically, contracture of hamstring muscles and other posterior hip tissues is evaluated by measuring the available range of hip flexion in straight leg raising. However, this does not provide any information on the elastic properties of the tissues. The present study reports a reliable method of evaluating such properties.

Mixed vitiligo of Blaschko lines: a newly discovered presentation of vitiligo responsive to combination treatment.

PubMed

Kovacevic, Maja; Stanimirovic, Andrija; Vucic, Majda; Goren, Andy; Situm, Mirna; Lukinovic Skudar, Vesna; Lotti, Torello

2016-07-01

Vitiligo, depigmenting disorder of the skin and mucous membranes, affects up to 1% of the population worldwide. It is classified into four major types: segmental, non-segmental, mixed, and unclassified type. Non-segmental vitiligo refers to non-dermatomal distribution of lesions, while dermatomal distribution of lesions is present in patients with segmental vitiligo. Segmental vitiligo can also follow Blaschko lines - pathways of epidermal cell migration and proliferation during the development of the fetus. Here, we present patient with segmental and non-segmental vitiligo following Blaschko lines with excellent therapeutic response to combined therapy. Prior to our report, a case of segmental and non-segmental vitiligo followed by Blaschko lines was never described, therefore we suggest the term "mixed vitiligo of Blaschko lines" to describe this entity. This is also a rare case in which 90% repigmentation was achieved in patient with segmental and nonsegmental vitiligo following Blaschko lines in only 2 months of combined therapy. © 2016 Wiley Periodicals, Inc.

Straight, white teeth as a social prerogative.

PubMed

Khalid, Abeer; Quiñonez, Carlos

2015-06-01

A distinguishing feature of North American society is preoccupation with self-image, as seen in the ritualistic nature of bodily practices aimed at constantly improving the body. Nowhere is this more apparent than in the prevailing fixation with straight, white teeth. While there is an ever-expanding literature on the sociology of body, very little has been written on teeth in this context. Using literature from anthropology, biology, dentistry, sociology and social psychology, this study attempts to answer: (1) Why have straight, white teeth become a beauty ideal in North American society? (2) What is the basis for this ideal? (3) How is this ideal propagated? It demonstrates that dental aesthetic tendencies are biologically, culturally and socially patterned. Concepts from the works of Pierre Bourdieu and Michel Foucault are used to illustrate how straight, white teeth contribute towards reinforcing class differences and how society exercises a disciplinary power on individuals through this ideal. It is concluded that modified teeth are linked to self and identity that are rooted in social structure. Moreover, teeth demonstrate the ways in which class differences are embodied and projected as symbols of social advantage or disadvantage. Implications on professional, public health, sociological and political levels are considered. © 2015 Foundation for the Sociology of Health & Illness.

KENTUCKY STRAIGHT PIPES REPORT, DECEMBER 2002

EPA Science Inventory

The poor sanitary conditions and water pollution problems EPA observed in the Kentucky counties of Harlan, Martin, Bath, and Montgomery were of the highest concern. The widespread scale of both the straight pipe issues as well as package plant wastewater problems present an envir...

Introgression of chromosome segments from multiple alien species in wheat breeding lines with wheat streak mosaic virus resistance.

PubMed

Ali, N; Heslop-Harrison, Js Pat; Ahmad, H; Graybosch, R A; Hein, G L; Schwarzacher, T

2016-08-01

Pyramiding of alien-derived Wheat streak mosaic virus (WSMV) resistance and resistance enhancing genes in wheat is a cost-effective and environmentally safe strategy for disease control. PCR-based markers and cytogenetic analysis with genomic in situ hybridisation were applied to identify alien chromatin in four genetically diverse populations of wheat (Triticum aestivum) lines incorporating chromosome segments from Thinopyrum intermedium and Secale cereale (rye). Out of 20 experimental lines, 10 carried Th. intermedium chromatin as T4DL*4Ai#2S translocations, while, unexpectedly, 7 lines were positive for alien chromatin (Th. intermedium or rye) on chromosome 1B. The newly described rye 1RS chromatin, transmitted from early in the pedigree, was associated with enhanced WSMV resistance. Under field conditions, the 1RS chromatin alone showed some resistance, while together with the Th. intermedium 4Ai#2S offered superior resistance to that demonstrated by the known resistant cultivar Mace. Most alien wheat lines carry whole chromosome arms, and it is notable that these lines showed intra-arm recombination within the 1BS arm. The translocation breakpoints between 1BS and alien chromatin fell in three categories: (i) at or near to the centromere, (ii) intercalary between markers UL-Thin5 and Xgwm1130 and (iii) towards the telomere between Xgwm0911 and Xbarc194. Labelled genomic Th. intermedium DNA hybridised to the rye 1RS chromatin under high stringency conditions, indicating the presence of shared tandem repeats among the cereals. The novel small alien fragments may explain the difficulty in developing well-adapted lines carrying Wsm1 despite improved tolerance to the virus. The results will facilitate directed chromosome engineering producing agronomically desirable WSMV-resistant germplasm.

Gay-Straight Alliances in High Schools: Social Predictors of Early Adoption

ERIC Educational Resources Information Center

Fetner, Tina; Kush, Kristin

2008-01-01

This article examines the patterns of emergence of gay-straight alliances (GSAs) in public high schools in the United States. These extracurricular student groups offer safe spaces, social support, and opportunities for activism to lesbian, gay, bisexual, transgender, queer, and straight students. Combining data on various characteristics of…

Questa Baseline and Pre-Mining Ground-Water Quality Investigation. 24. Seismic Refraction Tomography for Volume Analysis of Saturated Alluvium in the Straight Creek Drainage and Its Confluence With Red River, Taos County, New Mexico

USGS Publications Warehouse

Powers, Michael H.; Burton, Bethany L.

2007-01-01

As part of a research effort directed by the New Mexico Environment Department to determine pre-mining water quality of the Red River at a molybdenum mining site in northern New Mexico, we used seismic refraction tomography to create subsurface compressional-wave velocity images along six lines that crossed the Straight Creek drainage and three that crossed the valley of Red River. Field work was performed in June 2002 (lines 1-4) and September 2003 (lines 5-9). We interpreted the images to determine depths to the water table and to the top of bedrock. Depths to water and bedrock in boreholes near the lines correlate well with our interpretations based on seismic data. In general, the images suggest that the alluvium in this area has a trapezoidal cross section. Using a U.S. Geological Survey digital elevation model grid of surface elevations of this region and the interpreted elevations to water table and bedrock obtained from the seismic data, we generated new models of the shape of the buried bedrock surface and the water table through surface interpolation and extrapolation. Then, using elevation differences between the two grids, we calculated volumes of dry and wet alluvium in the two drainages. The Red River alluvium is about 51 percent saturated, whereas the much smaller volume of alluvium in the tributary Straight Creek is only about 18 percent saturated. When combined with average ground-water velocity values, the information we present can be used to determine discharge of Straight Creek into Red River relative to the total discharge of Red River moving past Straight Creek. This information will contribute to more accurate models of ground-water flow, which are needed to determine the pre-mining water quality in the Red River.

PROBABILISTIC HAZARD ASSESSMENT FOR TORNADOES, STRAIGHT-LINE WIND, AND EXTREME PRECIPITATION AT THE SAVANNAH RIVER SITE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Werth, D.; NOEMAIL), A.; Shine, G.

Recent data sets for three meteorological phenomena with the potential to inflict damage on SRS facilities - tornadoes, straight winds, and heavy precipitation - are analyzed using appropriate statistical techniques to estimate occurrence probabilities for these events in the future. Summaries of the results for DOE-mandated return periods and comparisons to similar calculations performed in 1998 by Weber, et al., are given. Using tornado statistics for the states of Georgia and South Carolina, we calculated the probability per year of any location within a 2⁰ square area surrounding SRS being struck by a tornado (the ‘strike’ probability) and the probabilitymore » that any point will experience winds above set thresholds. The strike probability was calculated to be 1.15E-3 (1 chance in 870) per year and wind speeds for DOE mandated return periods of 50,000 years, 125,000 years, and 1E+7 years (USDOE, 2012) were estimated to be 136 mph, 151 mph and 221 mph, respectively. In 1998 the strike probability for SRS was estimated to be 3.53 E-4 and the return period wind speeds were 148 mph every 50,000 years and 180 mph every 125,000 years. A 1E+7 year tornado wind speed was not calculated in 1998; however a 3E+6 year wind speed was 260 mph. The lower wind speeds resulting from this most recent analysis are largely due to new data since 1998, and to a lesser degree differences in the models used. By contrast, default tornado wind speeds taken from ANSI/ANS-2.3-2011 are somewhat higher: 161 mph for return periods of 50,000 years, 173 mph every 125,000 years, and 230 mph every 1E+7 years (ANS, 2011). Although the ANS model and the SRS models are very similar, the region defined in ANS 2.3 that encompasses the SRS also includes areas of the Great Plains and lower Midwest, regions with much higher occurrence frequencies of strong tornadoes. The SRS straight wind values associated with various return periods were calculated by fitting existing wind data to a Gumbel

METHOD AND MEANS FOR RECOGNIZING COMPLEX PATTERNS

DOEpatents

Hough, P.V.C.

1962-12-18

This patent relates to a method and means for recognizing a complex pattern in a picture. The picture is divided into framelets, each framelet being sized so that any segment of the complex pattern therewithin is essentially a straight line. Each framelet is scanned to produce an electrical pulse for each point scanned on the segment therewithin. Each of the electrical pulses of each segment is then transformed into a separate strnight line to form a plane transform in a pictorial display. Each line in the plane transform of a segment is positioned laterally so that a point on the line midway between the top and the bottom of the pictorial display occurs at a distance from the left edge of the pictorial display equal to the distance of the generating point in the segment from the left edge of the framelet. Each line in the plane transform of a segment is inclined in the pictorial display at an angle to the vertical whose tangent is proportional to the vertical displacement of the generating point in the segment from the center of the framelet. The coordinate position of the point of intersection of the lines in the pictorial display for each segment is determined and recorded. The sum total of said recorded coordinate positions being representative of the complex pattern. (AEC)

Document segmentation via oblique cuts

NASA Astrophysics Data System (ADS)

Svendsen, Jeremy; Branzan-Albu, Alexandra

2013-01-01

This paper presents a novel solution for the layout segmentation of graphical elements in Business Intelligence documents. We propose a generalization of the recursive X-Y cut algorithm, which allows for cutting along arbitrary oblique directions. An intermediate processing step consisting of line and solid region removal is also necessary due to presence of decorative elements. The output of the proposed segmentation is a hierarchical structure which allows for the identification of primitives in pie and bar charts. The algorithm was tested on a database composed of charts from business documents. Results are very promising.

Segmentation-driven compound document coding based on H.264/AVC-INTRA.

PubMed

Zaghetto, Alexandre; de Queiroz, Ricardo L

2007-07-01

In this paper, we explore H.264/AVC operating in intraframe mode to compress a mixed image, i.e., composed of text, graphics, and pictures. Even though mixed contents (compound) documents usually require the use of multiple compressors, we apply a single compressor for both text and pictures. For that, distortion is taken into account differently between text and picture regions. Our approach is to use a segmentation-driven adaptation strategy to change the H.264/AVC quantization parameter on a macroblock by macroblock basis, i.e., we deviate bits from pictorial regions to text in order to keep text edges sharp. We show results of a segmentation driven quantizer adaptation method applied to compress documents. Our reconstructed images have better text sharpness compared to straight unadapted coding, at negligible visual losses on pictorial regions. Our results also highlight the fact that H.264/AVC-INTRA outperforms coders such as JPEG-2000 as a single coder for compound images.

Gender, Health Behavior, and Intimate Relationships: Lesbian, Gay, and Straight Contexts

PubMed Central

Reczek, Corinne; Umberson, Debra

2012-01-01

Many studies focus on health behavior within the context of intimate ties. However, this literature is limited by reliance on gender socialization theory and a focus on straight (i.e., heterosexual) marriage. We extend this work with an analysis of relationship dynamics around health behavior in 20 long-term straight marriages as well as 15 gay and 15 lesbian long-term cohabiting partnerships in the United States (N=100 individual in-depth interviews). We develop the concept of “health behavior work” to align activities done to promote health behavior with theories on unpaid work in the home. Respondents in all couple types describe specialized health behavior work, wherein one partner works to shape the other partner’s health behavior. In straight couples, women perform the bulk of specialized health behavior work. Most gay and lesbian respondents—but few straight respondents—also describe cooperative health behavior work, wherein partners mutually influence one another’s health behaviors. Findings suggest that the gendered relational context of an intimate partnership shapes the dynamics of and explanations for health behavior work. PMID:22227238

Design on wireless auto-measurement system for lead rail straightness measurement based on PSD

NASA Astrophysics Data System (ADS)

Yan, Xiugang; Zhang, Shuqin; Dong, Dengfeng; Cheng, Zhi; Wu, Guanghua; Wang, Jie; Zhou, Weihu

2016-10-01

Straightness detection is not only one of the key technologies for the product quality and installation accuracy of all types of lead rail, but also an important dimensional measurement technology. The straightness measuring devices now available have disadvantages of low automation level, limiting by measuring environment, and low measurement efficiency. In this paper, a wireless measurement system for straightness detection based on position sensitive detector (PSD) is proposed. The system has some advantage of high automation-level, convenient, high measurement efficiency, easy to transplanting and expanding, and can detect straightness of lead rail in real-time.

Complexity and approximability for a problem of intersecting of proximity graphs with minimum number of equal disks

NASA Astrophysics Data System (ADS)

Kobylkin, Konstantin

2016-10-01

Computational complexity and approximability are studied for the problem of intersecting of a set of straight line segments with the smallest cardinality set of disks of fixed radii r > 0 where the set of segments forms straight line embedding of possibly non-planar geometric graph. This problem arises in physical network security analysis for telecommunication, wireless and road networks represented by specific geometric graphs defined by Euclidean distances between their vertices (proximity graphs). It can be formulated in a form of known Hitting Set problem over a set of Euclidean r-neighbourhoods of segments. Being of interest computational complexity and approximability of Hitting Set over so structured sets of geometric objects did not get much focus in the literature. Strong NP-hardness of the problem is reported over special classes of proximity graphs namely of Delaunay triangulations, some of their connected subgraphs, half-θ6 graphs and non-planar unit disk graphs as well as APX-hardness is given for non-planar geometric graphs at different scales of r with respect to the longest graph edge length. Simple constant factor approximation algorithm is presented for the case where r is at the same scale as the longest edge length.

Fluid-structure interaction in straight pipelines with different anchoring conditions

NASA Astrophysics Data System (ADS)

Ferras, David; Manso, Pedro A.; Schleiss, Anton J.; Covas, Dídia I. C.

2017-04-01

This investigation aims at assessing the fluid-structure interaction (FSI) occurring during hydraulic transients in straight pipeline systems fixed to anchor blocks. A two mode 4-equation model is implemented incorporating the main interacting mechanisms: Poisson, friction and junction coupling. The resistance to movement due to inertia and dry friction of the anchor blocks is treated as junction coupling. Unsteady skin friction is taken into account in friction coupling. Experimental waterhammer tests collected from a straight copper pipe-rig are used for model validation in terms of wave shape, timing and damping. Numerical results successfully reproduce laboratory measurements for realistic values of calibration parameters. The novelty of this paper is the presentation of a 1D FSI solver capable of describing the resistance to movement of anchor blocks and its effect on the transient pressure wave propagation in straight pipelines.

Intubation of prehospital patients with curved laryngoscope blade is more successful than with straight blade.

PubMed

Alter, Scott M; Haim, Eithan D; Sullivan, Alex H; Clayton, Lisa M

2018-02-17

Direct laryngoscopy can be performed using curved or straight blades, and providers usually choose the blade they are most comfortable with. However, curved blades are anecdotally thought of as easier to use than straight blades. We seek to compare intubation success rates of paramedics using curved versus straight blades. Design: retrospective chart review. hospital-based suburban ALS service with 20,000 annual calls. prehospital patients with any direct laryngoscopy intubation attempt over almost 9years. First attempt and overall success rates were calculated for attempts with curved and straight blades. Differences between the groups were calculated. 2299 patients were intubated by direct laryngoscopy. 1865 had attempts with a curved blade, 367 had attempts with a straight blade, and 67 had attempts with both. Baseline characteristics were similar between groups. First attempt success was 86% with a curved blade and 73% with a straight blade: a difference of 13% (95% CI: 9-17). Overall success was 96% with a curved blade and 81% with a straight blade: a difference of 15% (95% CI: 12-18). There was an average of 1.11 intubation attempts per patient with a curved blade and 1.13 attempts per patient with a straight blade (2% difference, 95% CI: -3-7). Our study found a significant difference in intubation success rates between laryngoscope blade types. Curved blades had higher first attempt and overall success rates when compared to straight blades. Paramedics should consider selecting a curved blade as their tool of choice to potentially improve intubation success. Copyright © 2018 Elsevier Inc. All rights reserved.

Time-varying impedance of the human ankle in the sagittal and frontal planes during straight walk and turning steps.

PubMed

Ficanha, Evandro M; Ribeiro, Guilherme A; Knop, Lauren; Rastgaar, Mo

2017-07-01

This paper describes the methods and experiment protocols for estimation of the human ankle impedance during turning and straight line walking. The ankle impedance of two human subjects during the stance phase of walking in both dorsiflexion plantarflexion (DP) and inversion eversion (IE) were estimated. The impedance was estimated about 8 axes of rotations of the human ankle combining different amounts of DP and IE rotations, and differentiating among positive and negative rotations at 5 instants of the stance length (SL). Specifically, the impedance was estimated at 10%, 30%, 50%, 70% and 90% of the SL. The ankle impedance showed great variability across time, and across the axes of rotation, with consistent larger stiffness and damping in DP than IE. When comparing straight walking and turning, the main differences were in damping at 50%, 70%, and 90% of the SL with an increase in damping at all axes of rotation during turning.

Document localization algorithms based on feature points and straight lines

NASA Astrophysics Data System (ADS)

Skoryukina, Natalya; Shemiakina, Julia; Arlazarov, Vladimir L.; Faradjev, Igor

2018-04-01

The important part of the system of a planar rectangular object analysis is the localization: the estimation of projective transform from template image of an object to its photograph. The system also includes such subsystems as the selection and recognition of text fields, the usage of contexts etc. In this paper three localization algorithms are described. All algorithms use feature points and two of them also analyze near-horizontal and near- vertical lines on the photograph. The algorithms and their combinations are tested on a dataset of real document photographs. Also the method of localization quality estimation is proposed that allows configuring the localization subsystem independently of the other subsystems quality.

Lingual straight wire method.

PubMed

Takemoto, Kyoto; Scuzzo, Giuseppe; Lombardo, L U C A; Takemoto, Y U I

2009-12-01

The mushroom arch-wire is mainly used in lingual orthodontic treatment but the complicated wire bending it requires affects both the treatment results and the time spent at the chair. The author proposes a new lingual straight wire method (LSW) in order to facilitate arch coordination and simplify the mechanics. The attention paid to the set-up model and bracket positioning and bonding plus the use of the new LSW method will also improve patient comfort. Copyright 2009 Collège Européen d'Orthodontie. Published by Elsevier Masson SAS.. All rights reserved.

Robust and automated three-dimensional segmentation of densely packed cell nuclei in different biological specimens with Lines-of-Sight decomposition.

PubMed

Mathew, B; Schmitz, A; Muñoz-Descalzo, S; Ansari, N; Pampaloni, F; Stelzer, E H K; Fischer, S C

2015-06-08

Due to the large amount of data produced by advanced microscopy, automated image analysis is crucial in modern biology. Most applications require reliable cell nuclei segmentation. However, in many biological specimens cell nuclei are densely packed and appear to touch one another in the images. Therefore, a major difficulty of three-dimensional cell nuclei segmentation is the decomposition of cell nuclei that apparently touch each other. Current methods are highly adapted to a certain biological specimen or a specific microscope. They do not ensure similarly accurate segmentation performance, i.e. their robustness for different datasets is not guaranteed. Hence, these methods require elaborate adjustments to each dataset. We present an advanced three-dimensional cell nuclei segmentation algorithm that is accurate and robust. Our approach combines local adaptive pre-processing with decomposition based on Lines-of-Sight (LoS) to separate apparently touching cell nuclei into approximately convex parts. We demonstrate the superior performance of our algorithm using data from different specimens recorded with different microscopes. The three-dimensional images were recorded with confocal and light sheet-based fluorescence microscopes. The specimens are an early mouse embryo and two different cellular spheroids. We compared the segmentation accuracy of our algorithm with ground truth data for the test images and results from state-of-the-art methods. The analysis shows that our method is accurate throughout all test datasets (mean F-measure: 91%) whereas the other methods each failed for at least one dataset (F-measure≤69%). Furthermore, nuclei volume measurements are improved for LoS decomposition. The state-of-the-art methods required laborious adjustments of parameter values to achieve these results. Our LoS algorithm did not require parameter value adjustments. The accurate performance was achieved with one fixed set of parameter values. We developed a novel and

BEAM TRANSPORT LINES FOR THE BSNS.

DOE Office of Scientific and Technical Information (OSTI.GOV)

WEI, J.

2006-06-26

This paper presents the design of two beam transport lines at the BSNS: one is the injection line from the Linac to the RCS and the other is the target line from the RCS to the target station. In the injection beam line, space charge effects, transverse halo collimation, momentum tail collimation and debunching are the main concerned topics. A new method of using triplet cells and stripping foils is used to collimate transverse halo. A long straight section is reserved for the future upgrading linac and debuncher. In the target beam line, large halo emittance, beam stability at themore » target due to kicker failures and beam jitters, shielding of back-scattering neutrons from the target are main concerned topics. Special bi-gap magnets will be used to reduce beam losses in the collimators in front of the target.« less

On-Line Detection and Segmentation of Sports Motions Using a Wearable Sensor.

PubMed

Kim, Woosuk; Kim, Myunggyu

2018-03-19

In sports motion analysis, observation is a prerequisite for understanding the quality of motions. This paper introduces a novel approach to detect and segment sports motions using a wearable sensor for supporting systematic observation. The main goal is, for convenient analysis, to automatically provide motion data, which are temporally classified according to the phase definition. For explicit segmentation, a motion model is defined as a sequence of sub-motions with boundary states. A sequence classifier based on deep neural networks is designed to detect sports motions from continuous sensor inputs. The evaluation on two types of motions (soccer kicking and two-handed ball throwing) verifies that the proposed method is successful for the accurate detection and segmentation of sports motions. By developing a sports motion analysis system using the motion model and the sequence classifier, we show that the proposed method is useful for observation of sports motions by automatically providing relevant motion data for analysis.

River channel patterns: Braided, meandering, and straight

USGS Publications Warehouse

Leopold, Luna Bergere; Wolman, M. Gordon

1957-01-01

Channel pattern is used to describe the plan view of a reach of river as seen from an airplane, and includes meandering, braiding, or relatively straight channels.Natural channels characteristically exhibit alternating pools or deep reaches and riffles or shallow reaches, regardless of the type of pattern. The length of the pool or distance between riffles in a straight channel equals the straight line distance between successive points of inflection in the wave pattern of a meandering river of the same width. The points of inflection are also shallow points and correspond to riffles in the straight channel. This distance, which is half the wavelength of the meander, varies approximately as a linear function of channel width. In the data we analysed the meander wavelength, or twice the distance between successive riffles, is from 7 to 12 times the channel width. It is concluded that the mechanics which may lead to meandering operate in straight channels.River braiding is characterized by channel division around alluvial islands. The growth of an island begins as the deposition of a central bar which results from sorting and deposition of the coarser fractions of the load which locally cannot be transported. The bar grows downstream and in height by continued deposition on its surface, forcing the water into the flanking channels, which, to carry the flow, deepen and cut laterally into the original banks. Such deepening locally lowers the water surface and the central bar emerges as an island which becomes stabilized by vegetation. Braiding was observed in a small river in a laboratory. Measurements of the adjustments of velocity, depth, width, and slope associated with island development lead to the conclusion that braiding is one of the many patterns which can maintain quasi-equilibrium among discharge, load, and transporting ability. Braiding does not necessarily indicate an excess of total load.Channel cross section and pattern are ultimately controlled by the

Demonstration of a Segment Alignment Maintenance System on a Seven-Segment Sub-Array of the Hobby-Eberly Telescope

NASA Technical Reports Server (NTRS)

Rakoczy, John; Whitaker, Ann F. (Technical Monitor)

2001-01-01

NASA's Marshall Space Flight Center, in collaboration with Blue Line Engineering of Colorado Springs, Colorado, is developing a Segment Alignment Maintenance System (SAMS) for McDonald Observatory's Hobby-Eberly Telescope (HET). The SAMS shall sense motions of the 91 primary mirror segments and send corrections to HET's primary mirror controller as the mirror segments misalign due to thermo-elastic deformations of the mirror support structure. The SAMS consists of inductive edge sensors supplemented by inclinometers for global radius of curvature sensing. All measurements are sent to the SAMS computer where mirror motion corrections are calculated. In October 2000, a prototype SAMS was installed on a seven-segment cluster of the HET. Subsequent testing has shown that the SAMS concept and architecture are a viable practical approach to maintaining HET's primary mirror figure, or the figure of any large segmented telescope. This paper gives a functional description of the SAMS sub-array components and presents test data to characterize the performance of the sub-array SAMS.

Automatic comic page image understanding based on edge segment analysis

NASA Astrophysics Data System (ADS)

Liu, Dong; Wang, Yongtao; Tang, Zhi; Li, Luyuan; Gao, Liangcai

2013-12-01

Comic page image understanding aims to analyse the layout of the comic page images by detecting the storyboards and identifying the reading order automatically. It is the key technique to produce the digital comic documents suitable for reading on mobile devices. In this paper, we propose a novel comic page image understanding method based on edge segment analysis. First, we propose an efficient edge point chaining method to extract Canny edge segments (i.e., contiguous chains of Canny edge points) from the input comic page image; second, we propose a top-down scheme to detect line segments within each obtained edge segment; third, we develop a novel method to detect the storyboards by selecting the border lines and further identify the reading order of these storyboards. The proposed method is performed on a data set consisting of 2000 comic page images from ten printed comic series. The experimental results demonstrate that the proposed method achieves satisfactory results on different comics and outperforms the existing methods.

Comparison of W-Plasty vs Traditional Straight-Line Techniques for Primary Paramedian Forehead Flap Donor Site Closure.

PubMed

Jáuregui, Emmanuel J; Tummala, Neelima; Seth, Rahul; Arron, Sarah; Neuhaus, Isaac; Yu, Siegrid; Grekin, Roy; Knott, P Daniel

2016-07-01

The paramedian forehead flap (PMFF) donor site scar is hard to disguise and may be a source of patient dissatisfaction. To evaluate the aesthetic outcome of W-plasty vs traditional straight-line (SL) closure techniques of the PMFF donor site. A retrospective cohort study was conducted at the University of California, San Francisco Medical Center. Clinical history and operative reports were reviewed for 31 patients who underwent a PMFF procedure performed between November 1, 2011, and May 29, 2014. Blinded photographic analysis of postoperative photographs was performed. The pedicled component of the PMFF was raised primarily with either a W-plasty or traditional SL design. Standard photographs of the donor site, obtained at least 90 days after surgery, were reviewed and scored in a blinded fashion by 4 dermatologic surgeons using a 100-point visual analog scale (from 0 [worst possible outcome] to 100 [best possible outcome]) and a 5-point Likert scale (from very poor to excellent). Interrater reliability was assessed via Cronbach α testing. All 31 forehead flaps survived during this study period; 16 PMFFs were raised with the W-plasty technique and 15 were raised with the SL technique. The W-plasty and SL groups were similar in terms of age, sex, and race/ethnicity (mean [SD] age, 68.4 [12.4] vs 61.8 [11.6] years; 13 [84%] vs 9 [60%] men; and 15 [94%] vs 13 [87%] white). Patients undergoing W-plasty closure had significantly higher mean visual analog scale scores compared with those undergoing SL closure (72.8 [18.3] vs 65.6 [18.1]; P = .03). Mean Likert scale scores for W-plasty were higher than those for SL closure, but the difference was not significant (3.77 [1.02] vs 3.43 [0.98]; P = .08). Overall interrater reliability for the visual analog scale and Likert scale scores were 0.67 and 0.58, respectively. Patients undergoing PMFF donor site closure using a primary W-plasty technique demonstrated better mean scar appearance of the forehead donor site

Segmentation of Object Outlines into Parts: A Large-Scale Integrative Study

ERIC Educational Resources Information Center

De Winter, Joeri; Wagemans, Johan

2006-01-01

In this study, a large number of observers (N=201) were asked to segment a collection of outlines derived from line drawings of everyday objects (N=88). This data set was then used as a benchmark to evaluate current models of object segmentation. All of the previously proposed rules of segmentation were found supported in our results. For example,…

A simple algorithm for computing positively weighted straight skeletons of monotone polygons☆

PubMed Central

Biedl, Therese; Held, Martin; Huber, Stefan; Kaaser, Dominik; Palfrader, Peter

2015-01-01

We study the characteristics of straight skeletons of monotone polygonal chains and use them to devise an algorithm for computing positively weighted straight skeletons of monotone polygons. Our algorithm runs in O(nlog⁡n) time and O(n) space, where n denotes the number of vertices of the polygon. PMID:25648376

A simple algorithm for computing positively weighted straight skeletons of monotone polygons.

PubMed

Biedl, Therese; Held, Martin; Huber, Stefan; Kaaser, Dominik; Palfrader, Peter

2015-02-01

We study the characteristics of straight skeletons of monotone polygonal chains and use them to devise an algorithm for computing positively weighted straight skeletons of monotone polygons. Our algorithm runs in [Formula: see text] time and [Formula: see text] space, where n denotes the number of vertices of the polygon.

Shallow high-resolution geophysical investigation along the western segment of the Victoria Lines Fault (island of Malta)

NASA Astrophysics Data System (ADS)

Villani, Fabio; D'Amico, Sebastiano; Panzera, Francesco; Vassallo, Maurizio; Bozionelos, George; Farrugia, Daniela; Galea, Pauline

2018-01-01

The Victoria Lines Fault (island of Malta) is a >15 km-long and N260°-striking segmented normal fault-system, which is probably inactive since the late Pliocene. In the westernmost part, the Fomm Ir-Rih segment displays comparable geologic throw and escarpment height ( 150-170 m), moreover its hangingwall hosts thin patches of Middle Pleistocene clastic continental deposits (red beds), which are poorly preserved elsewhere. We acquired two seismic transects, by collecting ambient vibration recordings, processed by using horizontal-to-vertical spectral ratios, complemented by one high-resolution 2-D refraction tomography survey crossing this fault where it is locally covered by red beds and recent colluvial deposits. We found a resonance peak at 1.0 Hz in the hangingwall block, whereas clear peaks in the range 5.0-10.0 Hz appear when approaching the subsurface fault, and we relate them to the fractured bedrock within the fault zone. The best-fit tomographic model shows a relatively high-Vp shallow body (Vp 2200-2400 m/s) that we relate to the weathered top of the Miocene Upper Coralline Limestone Fm., bounded on both sides by low-Vp regions (<1400 m/s). The latter are the smeared images of steep fault zones. Tomography further reveals a thick ( 15-20 m) low-Vp (<1000 m/s) zone, which could be a syn-tectonic wedge of colluvial deposits developed in the downthrown block. Surface waves analysis indicates lateral changes of the average shallow shear wave velocity, with Vs 130 m/s within the inferred fault zone, and Vs >230 m/s above the weathered top-bedrock. Our results depict a clear seismic signature of the Victoria Lines Fault, characterized by low seismic velocity and high amplification of ground motion. We hypothesize that, during the Middle Pleistocene, faulting may have affected the basal part of the red beds, so that this part of the investigated complex fault-system may be considered inactive since 0.6 Myr ago.

Gaussian-Beam/Physical-Optics Design Of Beam Waveguide

NASA Technical Reports Server (NTRS)

Veruttipong, Watt; Chen, Jacqueline C.; Bathker, Dan A.

1993-01-01

In iterative method of designing wideband beam-waveguide feed for paraboloidal-reflector antenna, Gaussian-beam approximation alternated with more nearly exact physical-optics analysis of diffraction. Includes curved and straight reflectors guiding radiation from feed horn to subreflector. For iterative design calculations, curved mirrors mathematically modeled as thin lenses. Each distance Li is combined length of two straight-line segments intersecting at one of flat mirrors. Method useful for designing beam-waveguide reflectors or mirrors required to have diameters approximately less than 30 wavelengths at one or more intended operating frequencies.

Beyond Line of Sight (BLOS) Command and Control (C2) Capability to Improve Disaster Response and Recovery

DTIC Science & Technology

2013-09-01

on the possible threat of an electromagnetic pulse (EMP) and its potential consequences following the destructive “ derecho ” that hit Washington, DC...in 2012.19 Spanish for the word “straight,” a derecho is a term used to describe a widespread, long- lived, straight-line windstorm that is...emergency communications system and raised concern for future response. Both Hurricane Katrina and the Washington, DC, area derecho have subsequently

Commissioning of the cryogenics of the LHC long straight sections

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perin, A.; Casas-Cubillos, J.; Claudet, S.

2010-01-01

The LHC is made of eight circular arcs interspaced with eight Long Straight Sections (LSS). Most powering interfaces to the LHC are located in these sections where the particle beams are focused and shaped for collision, cleaning and acceleration. The LSSs are constituted of several unique cryogenic devices and systems like electrical feed-boxes, standalone superconducting magnets, superconducting links, RF cavities and final focusing superconducting magnets. This paper presents the cryogenic commissioning and the main results obtained during the first operation of the LHC Long Straight Sections.

A method for smoothing segmented lung boundary in chest CT images

NASA Astrophysics Data System (ADS)

Yim, Yeny; Hong, Helen

2007-03-01

To segment low density lung regions in chest CT images, most of methods use the difference in gray-level value of pixels. However, radiodense pulmonary vessels and pleural nodules that contact with the surrounding anatomy are often excluded from the segmentation result. To smooth lung boundary segmented by gray-level processing in chest CT images, we propose a new method using scan line search. Our method consists of three main steps. First, lung boundary is extracted by our automatic segmentation method. Second, segmented lung contour is smoothed in each axial CT slice. We propose a scan line search to track the points on lung contour and find rapidly changing curvature efficiently. Finally, to provide consistent appearance between lung contours in adjacent axial slices, 2D closing in coronal plane is applied within pre-defined subvolume. Our method has been applied for performance evaluation with the aspects of visual inspection, accuracy and processing time. The results of our method show that the smoothness of lung contour was considerably increased by compensating for pulmonary vessels and pleural nodules.

Straight and Curved Conformations of FtsZ Are Regulated by GTP Hydrolysis

PubMed Central

Lu, Chunlin; Reedy, Mary; Erickson, Harold P.

2000-01-01

FtsZ assembles in vitro into protofilaments that can adopt two conformations—the straight conformation, which can assemble further into two-dimensional protofilament sheets, and the curved conformation, which forms minirings about 23 nm in diameter. Here, we describe the structure of FtsZ tubes, which are a variation of the curved conformation. In the tube the curved protofilament forms a shallow helix with a diameter of 23 nm and a pitch of 18 or 24°. We suggest that this shallow helix is the relaxed structure of the curved protofilament in solution. We provide evidence that GTP favors the straight conformation while GDP favors the curved conformation. In particular, exclusively straight protofilaments and protofilament sheets are assembled in GMPCPP, a nonhydrolyzable GTP analog, or in GTP following chelation of Mg, which blocks GTP hydrolysis. Assembly in GDP produces exclusively tubes. The transition from straight protofilaments to the curved conformation may provide a mechanism whereby the energy of GTP hydrolysis is used to generate force for the constriction of the FtsZ ring in cell division. PMID:10613876

Apparatus and method for routing a transmission line through a downhole tool

DOEpatents

Hall, David R.; Hall, Jr., H. Tracy; Pixton, David S.; Briscoe, Michael; Reynolds, Jay

2006-07-04

A method for routing a transmission line through a tool joint having a primary and secondary shoulder, a central bore, and a longitudinal axis, includes drilling a straight channel, at a positive, nominal angle with respect to the longitudinal axis, through the tool joint from the secondary shoulder to a point proximate the inside wall of the centtral bore. The method further includes milling back, from within the central bore, a second channel to merge with the straight channel, thereby forming a continuous channel from the secondary shoulder to the central bore. In selected embodiments, drilling is accomplished by gun-drilling the straight channel. In other embodiments, the method includes tilting the tool joint before drilling to produce the positive, nominal angle. In selected embodiments, the positive, nominal angle is less than or equal to 15 degrees.

The Hardest Straight-in Pool Shot

ERIC Educational Resources Information Center

Mabry, Rick

2010-01-01

When playing pool or billiards, a player often has the opportunity to make a "straight-in" shot, that is, one in which the cue ball, the object ball, and the target (e.g., a pocket) are collinear. With the distance from the cue ball to the target assumed fixed, the relative difficulty is here explored of shots taken at varying positions of the…

Evaluation of grout behind the lining of shield tunnels using ground-penetrating radar in the Shanghai Metro Line, China

NASA Astrophysics Data System (ADS)

Xie, Xiongyao; Liu, Yujian; Huang, Hongwei; Du, Jun; Zhang, Fengshou; Liu, Lanbo

2007-09-01

For shield tunnelling construction in soft soil areas, the coverage uniformity and quality of consolidation of the injected grout mortar behind the prefabricated tunnel segment is the main concern for tunnel safety and ground settlement. In this paper, ground-penetrating radar (GPR) was applied to evaluate the grout behind the tunnel lining segments in Shanghai, China. The dielectric permittivity of the grout material in Shanghai Metro tunnelling construction was measured in the laboratory. Combining physical modelling results with finite different time domain numerical modelling results, we suggest that the antenna with frequency 200 MHz is well suited to penetrate the reinforced steel bar network of the tunnel lining segment and testing grout patterns behind the segment. The electromagnetic velocity of the grout behind the segment of the tunnel is 0.1 m ns-1 by the analysis of field common-middle point data. A wave-translated method was put forward to process the GPR images. Furthermore, combining the information acquired by GPR with experience data, a GPR non-destructive test standard for the grout mortar evaluation in Shanghai Metro tunnel construction was brought forward. The grout behind the tunnel lining segment is classified into three types: uncompensated grout mortar with a thickness less than 10 cm, normal grout mortar with a thickness between 10 cm and 30 cm and overcompensated grout mortar, which is more than 30 cm thick. The classified method is easily put into practice.

Analysis of manual segmentation in paranasal CT images.

PubMed

Tingelhoff, Kathrin; Eichhorn, Klaus W G; Wagner, Ingo; Kunkel, Maria E; Moral, Analia I; Rilk, Markus E; Wahl, Friedrich M; Bootz, Friedrich

2008-09-01

Manual segmentation is often used for evaluation of automatic or semi-automatic segmentation. The purpose of this paper is to describe the inter and intraindividual variability, the dubiety of manual segmentation as a gold standard and to find reasons for the discrepancy. We realized two experiments. In the first one ten ENT surgeons, ten medical students and one engineer outlined the right maxillary sinus and ethmoid sinuses manually on a standard CT dataset of a human head. In the second experiment two participants outlined maxillary sinus and ethmoid sinuses five times consecutively. Manual segmentation was accomplished with custom software using a line segmentation tool. The first experiment shows the interindividual variability of manual segmentation which is higher for ethmoidal sinuses than for maxillary sinuses. The variability can be caused by the level of experience, different interpretation of the CT data or different levels of accuracy. The second experiment shows intraindividual variability which is lower than interindividual variability. Most variances in both experiments appear during segmentation of ethmoidal sinuses and outlining hiatus semilunaris. Concerning the inter and intraindividual variances the segmentation result of one manual segmenter could not directly be used as gold standard for the evaluation of automatic segmentation algorithms.

[Application of straight wire appliance for pre- and post-surgical orthodontics].

PubMed

Zhou, Yan-Heng; Sun, Yan-Nan; Hu, Wei; Fu, Min-Kui

2004-11-01

To analyze the surgical patients treated with straight wire appliance for guidelines of clinical using of the appliance. Totally 51 patients from Joint Clinic of Orthodontic Surgery, Peking University School of Stomatology with dentofacial deformities treated with straight wire appliance were analyzed. The patients were aged from 15 years to 34 years 5 months, average 18 years 9 months. Among whom, 16 are males, while the other 35 are females. Eighteen patients were treated with extraction of teeth, while other 33 cases were nonextraction case. The duration of average presurgical orthodontic treatment was 13.3 months, and 10.4 months was for postsurgical orthodontic treatment, totally active treatment time was 25.5 months. Straight wire appliance would benefit a lot for three dimensional control of teeth when doing pre- and post-surgical orthodontic treatment. Good results could be achieved without wire bending.

Improving the Lives of Students, Gay and Straight Alike: Gay-Straight Alliances and the Role of School Psychologists

ERIC Educational Resources Information Center

Murphy, Heather Elise

2012-01-01

Lesbian, gay, bisexual, and transgender (LGBT) students face many risk factors every day when they enter their school's door. These students often fear for their safety at school, are victimized, have academic difficulties, suffer from issues with their identity development, and are at risk for suicide. School-based Gay-Straight Alliances (GSAs)…

Segmentation of prostate biopsy needles in transrectal ultrasound images

NASA Astrophysics Data System (ADS)

Krefting, Dagmar; Haupt, Barbara; Tolxdorff, Thomas; Kempkensteffen, Carsten; Miller, Kurt

2007-03-01

Prostate cancer is the most common cancer in men. Tissue extraction at different locations (biopsy) is the gold-standard for diagnosis of prostate cancer. These biopsies are commonly guided by transrectal ultrasound imaging (TRUS). Exact location of the extracted tissue within the gland is desired for more specific diagnosis and provides better therapy planning. While the orientation and the position of the needle within clinical TRUS image are limited, the appearing length and visibility of the needle varies strongly. Marker lines are present and tissue inhomogeneities and deflection artefacts may appear. Simple intensity, gradient oder edge-detecting based segmentation methods fail. Therefore a multivariate statistical classificator is implemented. The independent feature model is built by supervised learning using a set of manually segmented needles. The feature space is spanned by common binary object features as size and eccentricity as well as imaging-system dependent features like distance and orientation relative to the marker line. The object extraction is done by multi-step binarization of the region of interest. The ROI is automatically determined at the beginning of the segmentation and marker lines are removed from the images. The segmentation itself is realized by scale-invariant classification using maximum likelihood estimation and Mahalanobis distance as discriminator. The technique presented here could be successfully applied in 94% of 1835 TRUS images from 30 tissue extractions. It provides a robust method for biopsy needle localization in clinical prostate biopsy TRUS images.

Groups of adjacent contour segments for object detection.

PubMed

Ferrari, V; Fevrier, L; Jurie, F; Schmid, C

2008-01-01

We present a family of scale-invariant local shape features formed by chains of k connected, roughly straight contour segments (kAS), and their use for object class detection. kAS are able to cleanly encode pure fragments of an object boundary, without including nearby clutter. Moreover, they offer an attractive compromise between information content and repeatability, and encompass a wide variety of local shape structures. We also define a translation and scale invariant descriptor encoding the geometric configuration of the segments within a kAS, making kAS easy to reuse in other frameworks, for example as a replacement or addition to interest points. Software for detecting and describing kAS is released on lear.inrialpes.fr/software. We demonstrate the high performance of kAS within a simple but powerful sliding-window object detection scheme. Through extensive evaluations, involving eight diverse object classes and more than 1400 images, we 1) study the evolution of performance as the degree of feature complexity k varies and determine the best degree; 2) show that kAS substantially outperform interest points for detecting shape-based classes; 3) compare our object detector to the recent, state-of-the-art system by Dalal and Triggs [4].

Minimum-fuel turning climbout and descent guidance of transport jets

NASA Technical Reports Server (NTRS)

Neuman, F.; Kreindler, E.

1983-01-01

The complete flightpath optimization problem for minimum fuel consumption from takeoff to landing including the initial and final turns from and to the runway heading is solved. However, only the initial and final segments which contain the turns are treated, since the straight-line climbout, cruise, and descent problems have already been solved. The paths are derived by generating fields of extremals, using the necessary conditions of optimal control together with singular arcs and state constraints. Results show that the speed profiles for straight flight and turning flight are essentially identical except for the final horizontal accelerating or decelerating turns. The optimal turns require no abrupt maneuvers, and an approximation of the optimal turns could be easily integrated with present straight-line climb-cruise-descent fuel-optimization algorithms. Climbout at the optimal IAS rather than the 250-knot terminal-area speed limit would save 36 lb of fuel for the 727-100 aircraft.

Advanced Dispersed Fringe Sensing Algorithm for Coarse Phasing Segmented Mirror Telescopes

NASA Technical Reports Server (NTRS)

Spechler, Joshua A.; Hoppe, Daniel J.; Sigrist, Norbert; Shi, Fang; Seo, Byoung-Joon; Bikkannavar, Siddarayappa A.

2013-01-01

Segment mirror phasing, a critical step of segment mirror alignment, requires the ability to sense and correct the relative pistons between segments from up to a few hundred microns to a fraction of wavelength in order to bring the mirror system to its full diffraction capability. When sampling the aperture of a telescope, using auto-collimating flats (ACFs) is more economical. The performance of a telescope with a segmented primary mirror strongly depends on how well those primary mirror segments can be phased. One such process to phase primary mirror segments in the axial piston direction is dispersed fringe sensing (DFS). DFS technology can be used to co-phase the ACFs. DFS is essentially a signal fitting and processing operation. It is an elegant method of coarse phasing segmented mirrors. DFS performance accuracy is dependent upon careful calibration of the system as well as other factors such as internal optical alignment, system wavefront errors, and detector quality. Novel improvements to the algorithm have led to substantial enhancements in DFS performance. The Advanced Dispersed Fringe Sensing (ADFS) Algorithm is designed to reduce the sensitivity to calibration errors by determining the optimal fringe extraction line. Applying an angular extraction line dithering procedure and combining this dithering process with an error function while minimizing the phase term of the fitted signal, defines in essence the ADFS algorithm.

Two-dimensional straightness measurement based on optical knife-edge sensing

NASA Astrophysics Data System (ADS)

Wang, Chen; Zhong, Fenghe; Ellis, Jonathan D.

2017-09-01

Straightness error is a parasitic translation along a perpendicular direction to the primary displacement axis of a linear stage. The parasitic translations could be coupled into other primary displacement directions of a multi-axis platform. Hence, its measurement and compensation are critical in precision multi-axis metrology, calibration, and manufacturing. This paper presents a two-dimensional (2D) straightness measurement configuration based on 2D optical knife-edge sensing, which is simple, light-weight, compact, and easy to align. It applies a 2D optical knife-edge to manipulate the diffraction pattern sensed by a quadrant photodetector, whose output voltages could derive 2D straightness errors after a calibration process. This paper analyzes the physical model of the configuration and performs simulations and experiments to study the system sensitivity, measurement nonlinearity, and error sources. The results demonstrate that the proposed configuration has higher sensitivity and insensitive to beam's vibration, compared with the conventional configurations without using the knife-edge, and could achieve ±0.25 μ m within a ±40 μ m measurement range along a 40 mm primary axial motion.

A Tracker for Broken and Closely-Spaced Lines

DTIC Science & Technology

1997-10-01

to combine the current level flow estimate and the previous level flow estimate. However, the result is still not good enough for some reasons. First...geometric attributes are not good enough to discriminate line segments, when they are crowded, parallel and closely-spaced to each other. On the other...level information [10]. Still, it is not good at dealing with closely-spaced line segments. Because it requires a proper size of square neighborhood to

49 CFR 192.179 - Transmission line valves.

Code of Federal Regulations, 2010 CFR

2010-10-01

... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Design of Pipeline Components § 192.179 Transmission line valves. (a) Each transmission line, other than offshore segments, must have sectionalizing block... 49 Transportation 3 2010-10-01 2010-10-01 false Transmission line valves. 192.179 Section 192.179...

49 CFR 192.179 - Transmission line valves.

Code of Federal Regulations, 2013 CFR

2013-10-01

... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Design of Pipeline Components § 192.179 Transmission line valves. (a) Each transmission line, other than offshore segments, must have sectionalizing block... 49 Transportation 3 2013-10-01 2013-10-01 false Transmission line valves. 192.179 Section 192.179...

49 CFR 192.179 - Transmission line valves.

Code of Federal Regulations, 2011 CFR

2011-10-01

... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Design of Pipeline Components § 192.179 Transmission line valves. (a) Each transmission line, other than offshore segments, must have sectionalizing block... 49 Transportation 3 2011-10-01 2011-10-01 false Transmission line valves. 192.179 Section 192.179...

49 CFR 192.179 - Transmission line valves.

Code of Federal Regulations, 2014 CFR

2014-10-01

... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Design of Pipeline Components § 192.179 Transmission line valves. (a) Each transmission line, other than offshore segments, must have sectionalizing block... 49 Transportation 3 2014-10-01 2014-10-01 false Transmission line valves. 192.179 Section 192.179...

49 CFR 192.179 - Transmission line valves.

Code of Federal Regulations, 2012 CFR

2012-10-01

... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Design of Pipeline Components § 192.179 Transmission line valves. (a) Each transmission line, other than offshore segments, must have sectionalizing block... 49 Transportation 3 2012-10-01 2012-10-01 false Transmission line valves. 192.179 Section 192.179...

Gay-Straight Alliance (GSA) Members' Engagement with Sex Education in Canadian High Schools

ERIC Educational Resources Information Center

Lapointe, Alicia

2014-01-01

This paper offers an examination of gay-straight alliance (GSA) members' engagement with sex education, sexual health, and prejudice and discrimination in Canadian public high schools. It explores how five students' (four straight and one gay-identifying) participation in GSAs served as a springboard for learning about and challenging stereotypes;…

Segmentation of Environmental Time Lapse Image Sequences for the Determination of Shore Lines Captured by Hand-Held Smartphone Cameras

NASA Astrophysics Data System (ADS)

Kröhnert, M.; Meichsner, R.

2017-09-01

The relevance of globally environmental issues gains importance since the last years with still rising trends. Especially disastrous floods may cause in serious damage within very short times. Although conventional gauging stations provide reliable information about prevailing water levels, they are highly cost-intensive and thus just sparsely installed. Smartphones with inbuilt cameras, powerful processing units and low-cost positioning systems seem to be very suitable wide-spread measurement devices that could be used for geo-crowdsourcing purposes. Thus, we aim for the development of a versatile mobile water level measurement system to establish a densified hydrological network of water levels with high spatial and temporal resolution. This paper addresses a key issue of the entire system: the detection of running water shore lines in smartphone images. Flowing water never appears equally in close-range images even if the extrinsics remain unchanged. Its non-rigid behavior impedes the use of good practices for image segmentation as a prerequisite for water line detection. Consequently, we use a hand-held time lapse image sequence instead of a single image that provides the time component to determine a spatio-temporal texture image. Using a region growing concept, the texture is analyzed for immutable shore and dynamic water areas. Finally, the prevalent shore line is examined by the resultant shapes. For method validation, various study areas are observed from several distances covering urban and rural flowing waters with different characteristics. Future work provides a transformation of the water line into object space by image-to-geometry intersection.

Robotic Vision-Based Localization in an Urban Environment

NASA Technical Reports Server (NTRS)

Mchenry, Michael; Cheng, Yang; Matthies

2007-01-01

A system of electronic hardware and software, now undergoing development, automatically estimates the location of a robotic land vehicle in an urban environment using a somewhat imprecise map, which has been generated in advance from aerial imagery. This system does not utilize the Global Positioning System and does not include any odometry, inertial measurement units, or any other sensors except a stereoscopic pair of black-and-white digital video cameras mounted on the vehicle. Of course, the system also includes a computer running software that processes the video image data. The software consists mostly of three components corresponding to the three major image-data-processing functions: Visual Odometry This component automatically tracks point features in the imagery and computes the relative motion of the cameras between sequential image frames. This component incorporates a modified version of a visual-odometry algorithm originally published in 1989. The algorithm selects point features, performs multiresolution area-correlation computations to match the features in stereoscopic images, tracks the features through the sequence of images, and uses the tracking results to estimate the six-degree-of-freedom motion of the camera between consecutive stereoscopic pairs of images (see figure). Urban Feature Detection and Ranging Using the same data as those processed by the visual-odometry component, this component strives to determine the three-dimensional (3D) coordinates of vertical and horizontal lines that are likely to be parts of, or close to, the exterior surfaces of buildings. The basic sequence of processes performed by this component is the following: 1. An edge-detection algorithm is applied, yielding a set of linked lists of edge pixels, a horizontal-gradient image, and a vertical-gradient image. 2. Straight-line segments of edges are extracted from the linked lists generated in step 1. Any straight-line segments longer than an arbitrary threshold (e

Comparison of W-Plasty and Straight-Line Trichophytic Closure on Aesthetic Outcomes of Occipital Hairline Scars in Rhytidectomy.

PubMed

Roy, Sudeep; Buckingham, Edward D

2018-01-01

Incision placement and design in rhytidectomy is critical for patient satisfaction. To evaluate the aesthetic outcome of W-plasty vs traditional straight-line (SL) trichophytic closure techniques on posterior occipital hairline scars in rhytidectomy. A retrospective cohort study was conducted at the Buckingham Center for Facial Plastic Surgery. Clinical history and operative reports were reviewed for 46 patients who underwent rhytidectomy (23 using W-plasty and 23 using SL technique) between June 1, 2014 and August 31, 2015. Blinded photographic analysis of 1-year postoperative photographs was performed. The posterior occipital hairline incision was primarily closed with either a W-plasty or SL trichophytic technique. Standard photographs of the posterior occipital incision site obtained after the 1-year postoperative mark were reviewed and scored in a blinded fashion by 3 nonphysician medical staff members using a modified Manchester Scar Scale (MSS: from 0 [best possible outcome] to 24 [worst possible outcome]). Interrater reliability was assessed via Cronbach α testing. There were 23 patients in each group. The W-plasty and SL groups were similar in terms of age (mean [SD] age, 59.6 [6.3] years and 64.1 [7.3] years, respectively), sex (21 [91%] and 21 [91%] women, respectively), race-ethnicity, and absence of risk factors (smoking and diabetes) predisposing to poor wound healing (0 and 0 smoking/diabetes, respectively). Mean (SD) follow-up times for the W-plasty and SL groups were 388 (38.8) and 475 (100.1) days, respectively. No statistical difference was demonstrated in the mean aggregate MSS scores from all evaluators between the W-plasty group and the SL group (reviewer 1: 5.69 vs 5.86, P = .60; reviewer 2: 10.09 vs 9.56, P = .65; and reviewer 3: 5.30 vs 6.17, P = .08). Overall interrater reliability for the MSS scores was 0.56. Primary W-plasty and SL trichophytic closures in the posterior occipital hairline appear to yield highly acceptable

[Biomechanical testing of the new torque-segmented arch (TSA)].

PubMed

Wichelhaus, A; Sander, F G

1995-07-01

New torque-segmented arch wires are presented which consist of a superelastic anterior component with 30 degrees or 45 degrees torque and which are connected to 2 steel lateral components by means of a crimped connector. When using such torque-segmented arch wires, the crimped connector rests mesially to the canine bracket and the lateral components exhibit a torque of 0 degree. The use of the torque-segmented arch wires requires the practitioner to adjust the anterior tooth segment, to bend in first order bends in the steel lateral portion as well as to bend in a sweep to avoid an anterior tooth extrusion, and, if desired, to bend in third order bends to influence premolars and molars. In some cases the simultaneous application of palatal arches can become necessary, because each torque transfer results in a transversal enlargement in the molar area. Compared to conventional steel wires with dimensions of 0.016 x 0.022 in which an anterior tooth torque is bent, the torque segmented arch wires exhibit considerably fewer side effects, but there is a larger distally rotating moment for the molars. 1. When applying torque-segmented arch wires, the extrusive force transferred to the anterior teeth is considerably smaller. 2. The protrusive force acting on the anterior teeth is also considerably smaller, which results in a reduced demand being placed on the anchorage of the molars. 3. The torque transfer to the incisors rests in a quite moderate range, even in the case of a 50 degrees torque. For this reason, the practitioner can expect diminished or no resorptions at all compared to the aforementioned steel wires. 4. The Martensite plateau of the torque-segmented arch wires exhibit constant moments in large areas so that such arch wires can be used in almost every anterior tooth position. 5. The segmented wires presented here can be applied not only in the case of the standard edgewise technique but also in each case of the straight-wire technique. 6. These new arch

Electromagnetic interaction in the theory of straight strings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nikitin, I.N.; Pron`ko, G.P.

1995-06-01

A scheme is proposed for including electromagnetic interaction into the theories of stretched relativistic objects. In the theory of the straight string, the operator of electromagnetic interaction is constructed, and form factors of electromagnetic transitions are calculated. 6 refs., 1 fig.

Finger vein recognition using local line binary pattern.

PubMed

Rosdi, Bakhtiar Affendi; Shing, Chai Wuh; Suandi, Shahrel Azmin

2011-01-01

In this paper, a personal verification method using finger vein is presented. Finger vein can be considered more secured compared to other hands based biometric traits such as fingerprint and palm print because the features are inside the human body. In the proposed method, a new texture descriptor called local line binary pattern (LLBP) is utilized as feature extraction technique. The neighbourhood shape in LLBP is a straight line, unlike in local binary pattern (LBP) which is a square shape. Experimental results show that the proposed method using LLBP has better performance than the previous methods using LBP and local derivative pattern (LDP).

Space Adaptation of Active Mirror Segment Concepts

NASA Technical Reports Server (NTRS)

Ames, Gregory H.

1999-01-01

This report summarizes the results of a three year effort by Blue Line Engineering Co. to advance the state of segmented mirror systems in several separate but related areas. The initial set of tasks were designed to address the issues of system level architecture, digital processing system, cluster level support structures, and advanced mirror fabrication concepts. Later in the project new tasks were added to provide support to the existing segmented mirror testbed at Marshall Space Flight Center (MSFC) in the form of upgrades to the 36 subaperture wavefront sensor. Still later, tasks were added to build and install a new system processor based on the results of the new system architecture. The project was successful in achieving a number of important results. These include the following most notable accomplishments: 1) The creation of a new modular digital processing system that is extremely capable and may be applied to a wide range of segmented mirror systems as well as many classes of Multiple Input Multiple Output (MIMO) control systems such as active structures or industrial automation. 2) A new graphical user interface was created for operation of segmented mirror systems. 3) The development of a high bit rate serial data loop that permits bi-directional flow of data to and from as many as 39 segments daisy-chained to form a single cluster of segments. 4) Upgrade of the 36 subaperture Hartmann type Wave Front Sensor (WFS) of the Phased Array Mirror, Extendible Large Aperture (PAMELA) testbed at MSFC resulting in a 40 to 5OX improvement in SNR which in turn enabled NASA personnel to achieve many significant strides in improved closed-loop system operation in 1998. 5) A new system level processor was built and delivered to MSFC for use with the PAMELA testbed. This new system featured a new graphical user interface to replace the obsolete and non-supported menu system originally delivered with the PAMELA system. The hardware featured Blue Line's new stackable

Straight Privilege: Unpacking the (Still) Invisible Knapsack

ERIC Educational Resources Information Center

Tollefson, Kaia

2010-01-01

Several unearned benefits attending straight privilege are listed, prefaced by two main arguments. First, it is argued that the rampant heterosexism in the U.S. is largely attributable to many Americans' framing of heterosexism as a matter of religious freedom rather than as a form of bigotry. It is further argued that educators' elimination of…

Straight SU-8 pins

NASA Astrophysics Data System (ADS)

Safavieh, R.; Pla Roca, M.; Qasaimeh, M. A.; Mirzaei, M.; Juncker, D.

2010-05-01

SU-8 can be patterned with high resolution, is flexible and tough. These characteristics qualify SU-8 as a material for making spotting pins for printing DNA and protein microarrays, and it can potentially replace the commonly used silicon and steel pins that are expensive, brittle in the case of silicon and can damage the substrate during the printing process. SU-8, however, accumulates large internal stress during fabrication and, as a consequence, thin and long SU-8 structures bend and coil up, which precludes using it for long, freestanding structures such as pins. Here we introduce (i) a novel fabrication process that allows the making of 30 mm long, straight spotting pins that feature (ii) a new design and surface chemistry treatments for better capillary flow control and more homogeneous spotting. A key innovation for the fabrication is a post-processing annealing step with slow temperature ramping and mechanical clamping between two identical substrates to minimize stress buildup and render it symmetric, respectively, which together yield a straight SU-8 structure. SU-8 pins fabricated using this process are compliant and resilient and can buckle without damage during printing. The pins comprise a novel flow stop valve for accurate metering of fluids, and their surface was chemically patterned to render the outside of the pin hydrophobic while the inside of the slit is hydrophilic, and the slit thus spontaneously fills when dipped into a solution while preventing droplet attachment on the outside. A single SU-8 pin was used to print 1392 protein spots in one run. SU-8 pins are inexpensive, straightforward to fabricate, robust and may be used as disposable pins for microarray fabrication. These pins serve as an illustration of the potential application of ultralow stress SU-8 for making freestanding microfabricated polymer microstructures.

The adaptive variant EDARV370A is associated with straight hair in East Asians.

PubMed

Tan, Jingze; Yang, Yajun; Tang, Kun; Sabeti, Pardis C; Jin, Li; Wang, Sijia

2013-10-01

Hair straightness/curliness is a highly heritable trait amongst human populations. Previous studies have reported European specific genetic variants influencing hair straightness, but those in East Asians remain unknown. One promising candidate is a derived coding variant of the ectodysplasin A receptor (EDAR), EDARV370A (370A), associated with several phenotypic changes of epidermal appendages. One of the strongest signals of natural selection in human genomes, 370A, has risen to high prevalence in East Asian and Native American populations, whilst being almost absent in Europeans and Africans. This striking frequency distribution and the pleiotropic nature of 370A led us to pursue if hair straightness, another epidermal appendage-related phenotype, is affected by this variant. By studying 1,718 individuals from four distinctive East Asian populations (Han, Tibetan, Mongolian, and Li), we found a significant association between 370A and the straight hair type in the Han (p = 2.90 × 10(-6)), Tibetan (p = 3.07 × 10(-2)), and Mongolian (p = 1.03 × 10(-5)) populations. Combining all the samples, the association is even stronger (p = 5.18 × 10(-10)). The effect of 370A on hair straightness is additive, with an odds ratio of 2.05. The results indicate very different biological mechanisms of straight hair in Europe and Asia, and also present a more comprehensive picture of the phenotypic consequences of 370A, providing important clues into the potential adaptive forces shaping the evolution of this extraordinary genetic variant.

21 CFR 70.20 - Packaging requirements for straight colors (other than hair dyes).

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Packaging requirements for straight colors (other than hair dyes). 70.20 Section 70.20 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL COLOR ADDITIVES Packaging and Labeling § 70.20 Packaging requirements for straight colors (other than hair dyes)....

The Efficacy of FlexMaster's IntroFile, PreRaCe and Gates Glidden Drills in Straight-Line Access: A CBCT Assessment.

PubMed

Farhad Mollashahi, Narges; Sohrabi, Mahdi; Farhad Mollashahi, Leila; Mehdizadeh, Mojdeh

2014-01-01

An overlooked but important part of successful root canal treatment is a straight-line access (SLA). The purpose of this in vitro study was to compare the efficacy of IntroFile and PreRaCe rotary instruments with Gates Glidden (GG) drills in gaining SLA by cone-beam computed tomography (CBCT). A total of forty five extracted mandibular first molars were selected and mounted in dental like arches. Subsequently, they were randomly classified into three groups (n=15). After preparation of a standard access cavity, orifices of the mesiobuccal canal was reached and a #10 file was inserted to explore the canals until the file tip was visible at the apex. Then, preoperative CBCT images were taken. SLA was gained in three groups; group 1, FlexMaster's IntroFile (FM); group 2, PreRaCe (RC) and group 3, GG. Again, the first binding file at the working length (WL) was placed in the canal and postoperative CBCT images in similar positions were taken. The pre/post operative morphology of the canal was evaluated for changes. Data was analyzed using the one-way ANOVA and post-hoc Bonferroni analysis. The average amount of reduction in coronal canal curvature in FM, RC and GG groups was 2.43±1.79, 3.17±2.05 and 8.7±3.45, respectively. This descending trend was statistically significant. The difference between pre/post SLA changes in FM and RC groups was significant compared to GG group, while there were no significant differences between RC and FM. GG drills produced extraordinary results in reducing coronal curvature of the canal and achieving SLA. They are also more effective than nickel-titanium (NiTi) rotary instruments in canals with coronal curvature.

Film-cooling effectiveness with developing coolant flow through straight and curved tubular passages

NASA Technical Reports Server (NTRS)

Papell, S. S.; Wang, C. R.; Graham, R. W.

1982-01-01

The data were obtained with an apparatus designed to determine the influence of tubular coolant passage curvature on film-cooling performance while simulating the developing flow entrance conditions more representative of cooled turbine blade. Data comparisons were made between straight and curved single tubular passages embedded in the wall and discharging at 30 deg angle in line with the tunnel flow. The results showed an influence of curvature on film-cooling effectiveness that was inversely proportional to the blowing rate. At the lowest blowing rate of 0.18, curvature increased the effectiveness of film cooling by 35 percent; but at a blowing rate of 0.76, the improvement was only 10 percent. In addition, the increase in film-cooling area coverage ranged from 100 percent down to 25 percent over the same blowing rates. A data trend reversal at a blowing rate of 1.5 showed the straight tubular passage's film-cooling effectiveness to be 20 percent greater than that of the curved passage with about 80 percent more area coverage. An analysis of turbulence intensity detain the mixing layer in terms of the position of the mixing interface relative to the wall supported the concept that passage curvature tends to reduce the diffusion of the coolant jet into the main stream at blowing rates below about. Explanations for the film-cooling performance of both test sections were made in terms differences in turbulences structure and in secondary flow patterns within the coolant jets as influenced by flow passage geometry.

Film-cooling effectiveness with developing coolant flow through straight and curved tubular passages

NASA Astrophysics Data System (ADS)

Papell, S. S.; Wang, C. R.; Graham, R. W.

1982-11-01

The data were obtained with an apparatus designed to determine the influence of tubular coolant passage curvature on film-cooling performance while simulating the developing flow entrance conditions more representative of cooled turbine blade. Data comparisons were made between straight and curved single tubular passages embedded in the wall and discharging at 30 deg angle in line with the tunnel flow. The results showed an influence of curvature on film-cooling effectiveness that was inversely proportional to the blowing rate. At the lowest blowing rate of 0.18, curvature increased the effectiveness of film cooling by 35 percent; but at a blowing rate of 0.76, the improvement was only 10 percent. In addition, the increase in film-cooling area coverage ranged from 100 percent down to 25 percent over the same blowing rates. A data trend reversal at a blowing rate of 1.5 showed the straight tubular passage's film-cooling effectiveness to be 20 percent greater than that of the curved passage with about 80 percent more area coverage. An analysis of turbulence intensity detain the mixing layer in terms of the position of the mixing interface relative to the wall supported the concept that passage curvature tends to reduce the diffusion of the coolant jet into the main stream at blowing rates below about. Explanations for the film-cooling performance of both test sections were made in terms differences in turbulences structure and in secondary flow patterns within the coolant jets as influenced by flow passage geometry.

Real-time biscuit tile image segmentation method based on edge detection.

PubMed

Matić, Tomislav; Aleksi, Ivan; Hocenski, Željko; Kraus, Dieter

2018-05-01

In this paper we propose a novel real-time Biscuit Tile Segmentation (BTS) method for images from ceramic tile production line. BTS method is based on signal change detection and contour tracing with a main goal of separating tile pixels from background in images captured on the production line. Usually, human operators are visually inspecting and classifying produced ceramic tiles. Computer vision and image processing techniques can automate visual inspection process if they fulfill real-time requirements. Important step in this process is a real-time tile pixels segmentation. BTS method is implemented for parallel execution on a GPU device to satisfy the real-time constraints of tile production line. BTS method outperforms 2D threshold-based methods, 1D edge detection methods and contour-based methods. Proposed BTS method is in use in the biscuit tile production line. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

Straight studs from southern pine veneer cores and cordwood

Treesearch

Peter Koch

1968-01-01

An economically feasible system has been developed for converting southern pine veneer cores into straight 8-foot studs (2). Prototype studs - two per core - were 100 percent SPIB stud grade and better.

Deck plan with straight and winged bulkheads Promontory Route ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Deck plan with straight and winged bulkheads - Promontory Route Railroad Trestles, S.P. Trestle 779.91, One mile southwest of junction of State Highway 83 and Blue Creek, Corinne, Box Elder County, UT

A heterodyne straightness and displacement measuring interferometer with laser beam drift compensation for long-travel linear stage metrology.

PubMed

Chen, Benyong; Cheng, Liang; Yan, Liping; Zhang, Enzheng; Lou, Yingtian

2017-03-01

The laser beam drift seriously influences the accuracy of straightness or displacement measurement in laser interferometers, especially for the long travel measurement. To solve this problem, a heterodyne straightness and displacement measuring interferometer with laser beam drift compensation is proposed. In this interferometer, the simultaneous measurement of straightness error and displacement is realized by using heterodyne interferometry, and the laser beam drift is determined to compensate the measurement results of straightness error and displacement in real time. The optical configuration of the interferometer is designed. The principle of the simultaneous measurement of straightness, displacement, and laser beam drift is depicted and analyzed in detail. And the compensation of the laser beam drift for the straightness error and displacement is presented. Several experiments were performed to verify the feasibility of the interferometer and the effectiveness of the laser beam drift compensation. The experiments of laser beam stability show that the position stability of the laser beam spot can be improved by more than 50% after compensation. The measurement and compensation experiments of straightness error and displacement by testing a linear stage at different distances show that the straightness and displacement obtained from the interferometer are in agreement with those obtained from a compared interferometer and the measured stage. These demonstrate that the merits of this interferometer are not only eliminating the influence of laser beam drift on the measurement accuracy but also having the abilities of simultaneous measurement of straightness error and displacement as well as being suitable for long-travel linear stage metrology.

School Climate, Individual Support, or Both? Gay-Straight Alliances and the Mental Health of Sexual Minority Youth

ERIC Educational Resources Information Center

Walls, N. Eugene; Wisneski, Hope; Kane, Sarah

2013-01-01

Using a sample of 284 sexual minority youth and young adults, this paper examines the relationships between mental health variables, the absence or presence of a gay-straight alliance, and membership status in a gay-straight alliance. The results suggest that the presence of a gay-straight alliance in a school or college, rather than actual…

14 CFR 417.215 - Straight-up time analysis.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 4 2014-01-01 2014-01-01 false Straight-up time analysis. 417.215 Section 417.215 Aeronautics and Space COMMERCIAL SPACE TRANSPORTATION, FEDERAL AVIATION ADMINISTRATION... vehicle's flight termination system or breakup of the launch vehicle would not cause hazardous debris or...

14 CFR 417.215 - Straight-up time analysis.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Straight-up time analysis. 417.215 Section 417.215 Aeronautics and Space COMMERCIAL SPACE TRANSPORTATION, FEDERAL AVIATION ADMINISTRATION... vehicle's flight termination system or breakup of the launch vehicle would not cause hazardous debris or...

14 CFR 417.215 - Straight-up time analysis.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 4 2011-01-01 2011-01-01 false Straight-up time analysis. 417.215 Section 417.215 Aeronautics and Space COMMERCIAL SPACE TRANSPORTATION, FEDERAL AVIATION ADMINISTRATION... vehicle's flight termination system or breakup of the launch vehicle would not cause hazardous debris or...

14 CFR 417.215 - Straight-up time analysis.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 4 2013-01-01 2013-01-01 false Straight-up time analysis. 417.215 Section 417.215 Aeronautics and Space COMMERCIAL SPACE TRANSPORTATION, FEDERAL AVIATION ADMINISTRATION... vehicle's flight termination system or breakup of the launch vehicle would not cause hazardous debris or...

14 CFR 417.215 - Straight-up time analysis.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 4 2012-01-01 2012-01-01 false Straight-up time analysis. 417.215 Section 417.215 Aeronautics and Space COMMERCIAL SPACE TRANSPORTATION, FEDERAL AVIATION ADMINISTRATION... vehicle's flight termination system or breakup of the launch vehicle would not cause hazardous debris or...

A Straight-Talk Survival Guide for Colleges

ERIC Educational Resources Information Center

Facione, Peter A.

2009-01-01

Times are very tough. The great majority of colleges are looking at 2009 and 2010 and beyond, in anticipation of the deepest budget cuts in more than a generation. But as bad as the financial situation may be, colleges can survive if they take swift and strong emergency action. It is time for some straight talk, starting with the realization that…

Self-Paced Physics, Segments 19-23.

ERIC Educational Resources Information Center

New York Inst. of Tech., Old Westbury.

Five study segments of the Self-Paced Physics Course materials are presented in this fourth problems and solutions book used as a part of student course work. The subject matter is related to electric charges, insulators, Coulomb's law, electric fields, lines of force, solid angles, conductors, motion of charged particles, dipoles, electric flux,…

Investigation into the limitations of straightness interferometers using a multisensor-based error separation method

NASA Astrophysics Data System (ADS)

Weichert, Christoph; Köchert, Paul; Schötka, Eugen; Flügge, Jens; Manske, Eberhard

2018-06-01

The uncertainty of a straightness interferometer is independent of the component used to introduce the divergence angle between the two probing beams, and is limited by three main error sources, which are linked to each other: their resolution, the influence of refractive index gradients and the topography of the straightness reflector. To identify the configuration with minimal uncertainties under laboratory conditions, a fully fibre-coupled heterodyne interferometer was successively equipped with three different wedge prisms, resulting in three different divergence angles (4°, 8° and 20°). To separate the error sources an independent reference with a smaller reproducibility is needed. Therefore, the straightness measurement capability of the Nanometer Comparator, based on a multisensor error separation method, was improved to provide measurements with a reproducibility of 0.2 nm. The comparison results revealed that the influence of the refractive index gradients of air did not increase with interspaces between the probing beams of more than 11.3 mm. Therefore, over a movement range of 220 mm, the lowest uncertainty was achieved with the largest divergence angle. The dominant uncertainty contribution arose from the mirror topography, which was additionally determined with a Fizeau interferometer. The measured topography agreed within  ±1.3 nm with the systematic deviations revealed in the straightness comparison, resulting in an uncertainty contribution of 2.6 nm for the straightness interferometer.

49 CFR 238.119 - Rim-stamped straight-plate wheels.

Code of Federal Regulations, 2010 CFR

2010-10-01

... input to the wheel during braking. (b) A rim-stamped straight-plate wheel shall not be used as a... that is periodically tread-braked for a short duration by automatic circuitry for the sole purpose of...

Relationships among the slopes of lines derived from various data analysis techniques and the associated correlation coefficient

NASA Technical Reports Server (NTRS)

Cohen, S. C.

1980-01-01

A technique for fitting a straight line to a collection of data points is given. The relationships between the slopes and correlation coefficients, and between the corresponding standard deviations and correlation coefficient are given.

Finger Vein Recognition Using Local Line Binary Pattern

PubMed Central

Rosdi, Bakhtiar Affendi; Shing, Chai Wuh; Suandi, Shahrel Azmin

2011-01-01

In this paper, a personal verification method using finger vein is presented. Finger vein can be considered more secured compared to other hands based biometric traits such as fingerprint and palm print because the features are inside the human body. In the proposed method, a new texture descriptor called local line binary pattern (LLBP) is utilized as feature extraction technique. The neighbourhood shape in LLBP is a straight line, unlike in local binary pattern (LBP) which is a square shape. Experimental results show that the proposed method using LLBP has better performance than the previous methods using LBP and local derivative pattern (LDP). PMID:22247670

An algorithm to help design fire simulation and other data base work

Treesearch

Romain Mees

1974-01-01

The data necessary for fire simulation may be made available through an algorithm based on tracing of boundaries composed of straight-line segments. Useful assumptions are that if a closed boundary does not contain a given point, then any other closed boundary contained within the former one does not contain the location; and that a given location will be contained in...

A Comparison of Best Fit Lines for Data with Outliers

ERIC Educational Resources Information Center

Glaister, P.

2005-01-01

Three techniques for determining a straight line fit to data are compared. The methods are applied to a range of datasets containing one or more outliers, and to a specific example from the field of chemistry. For the method which is the most resistant to the presence of outliers, a Microsoft Excel spreadsheet, as well as two Matlab routines, are…

Custom-Made Pyramids.

DTIC Science & Technology

1986-11-01

V2 + V 2 2 We can formulate the general weighted resampling formulas by giving an inter - polation formula and a sampling formula. Specifically...tessellation grids. 4.1. One-dimensional Adaptive Pyramid We suggest an interest operator based on the local " busyness " of the data. It has been observed...that in human perception a line with higher " busyness " seems longer than a straight line segment [6], as in Figure 7. Here, we will use a smoothed

Apparatus for correcting precision errors in slide straightness in machine tools

DOEpatents

Robinson, Samuel C.; Gerth, Howard L.

1981-01-01

The present invention is directed to a mechanism by which small deviations in slideway straightness and roll of a precision machining apparatus may be compensated for. The mechanism of the present invention comprises a fixture support disposed between the slideway carriage and the tool or workpiece fixture and provided with a hinge-like coupling between the carriage and the fixture support so as to allow for the minute and precise displacement of the fixture support in a direction normal to the direction of the slide path so as to readily compensate for slight deviations in the straightness and roll of the slide path.

Seamless contiguity method for parallel segmentation of remote sensing image

NASA Astrophysics Data System (ADS)

Wang, Geng; Wang, Guanghui; Yu, Mei; Cui, Chengling

2015-12-01

Seamless contiguity is the key technology for parallel segmentation of remote sensing data with large quantities. It can be effectively integrate fragments of the parallel processing into reasonable results for subsequent processes. There are numerous methods reported in the literature for seamless contiguity, such as establishing buffer, area boundary merging and data sewing. et. We proposed a new method which was also based on building buffers. The seamless contiguity processes we adopt are based on the principle: ensuring the accuracy of the boundary, ensuring the correctness of topology. Firstly, block number is computed based on data processing ability, unlike establishing buffer on both sides of block line, buffer is established just on the right side and underside of the line. Each block of data is segmented respectively and then gets the segmentation objects and their label value. Secondly, choose one block(called master block) and do stitching on the adjacent blocks(called slave block), process the rest of the block in sequence. Through the above processing, topological relationship and boundaries of master block are guaranteed. Thirdly, if the master block polygons boundaries intersect with buffer boundary and the slave blocks polygons boundaries intersect with block line, we adopt certain rules to merge and trade-offs them. Fourthly, check the topology and boundary in the buffer area. Finally, a set of experiments were conducted and prove the feasibility of this method. This novel seamless contiguity algorithm provides an applicable and practical solution for efficient segmentation of massive remote sensing image.

Segment Alignment Maintenance System for the Hobby-Eberly Telescope

NASA Technical Reports Server (NTRS)

Rakoczy, John; Burdine, Robert (Technical Monitor)

2001-01-01

NASA's Marshall Space Flight Center, in collaboration with Blue Line Engineering of Colorado Springs, Colorado, is developing a Segment Alignment Maintenance System (SAMS) for McDonald Observatory's Hobby-Eberly Telescope (HET). The SAMS shall sense motions of the 91 primary mirror segments and send corrections to HET's primary mirror controller as the mirror segments misalign due to thermo -elastic deformations of the mirror support structure. The SAMS consists of inductive edge sensors. All measurements are sent to the SAMS computer where mirror motion corrections are calculated. In October 2000, a prototype SAMS was installed on a seven-segment cluster of the HET. Subsequent testing has shown that the SAMS concept and architecture are a viable practical approach to maintaining HET's primary mirror figure, or the figure of any large segmented telescope. This paper gives a functional description of the SAMS sub-array components and presents test data to characterize the performance of the subarray SAMS.

Straight ahead running of a nonlinear car and driver model - new nonlinear behaviours highlighted

NASA Astrophysics Data System (ADS)

Della Rossa, Fabio; Mastinu, Giampiero

2018-05-01

The paper deals with the bifurcation analysis of a validated simple model describing a vehicle+driver running straight ahead. The mechanical model of the car has two degrees of freedom and the related equations of motion contain the nonlinear tyre characteristics. The driver is described by a very simple model. Bifurcation analysis is adopted for characterising straight ahead motion at different speeds for different drivers. A nonlinear sensitivity analysis is performed as a function of the driver's parameters and forward vehicle speed. A wealth of unreferenced bifurcations is discovered both for the understeering (UN) and for the oversteering (OV) vehicle. For the UN vehicle, a supercritical Hopf bifurcation may occur as the forward speed is increased. Also tangent (fold) bifurcations (saddle-node bifurcation of limit cycles) occur as the speed (or disturbance) is further increased. For the OV vehicle, a subcritical Hopf bifurcation occurs as the speed reaches a critical value. The preview distance (a driver's control parameter) plays a fundamental role in straight ahead driving. Either too short or too long preview distances are negative for straight ahead running.

"Appearance potent"? A content analysis of UK gay and straight men's magazines.

PubMed

Jankowski, Glen S; Fawkner, Helen; Slater, Amy; Tiggemann, Marika

2014-09-01

With little actual appraisal, a more 'appearance potent' (i.e., a reverence for appearance ideals) subculture has been used to explain gay men's greater body dissatisfaction in comparison to straight men's. This study sought to assess the respective appearance potency of each subculture by a content analysis of 32 issues of the most read gay (Attitude, Gay Times) and straight men's magazines (Men's Health, FHM) in the UK. Images of men and women were coded for their physical characteristics, objectification and nudity, as were the number of appearance adverts and articles. The gay men's magazines featured more images of men that were appearance ideal, nude and sexualized than the straight men's magazines. The converse was true for the images of women and appearance adverts. Although more research is needed to understand the effect of this content on the viewer, the findings are consistent with a more appearance potent gay male subculture. Crown Copyright © 2014. Published by Elsevier Ltd. All rights reserved.

Compact microchannel system

DOEpatents

Griffiths, Stewart

2003-09-30

The present invention provides compact geometries for the layout of microchannel columns through the use of turns and straight channel segments. These compact geometries permit the use of long separation or reaction columns on a small microchannel substrate or, equivalently, permit columns of a fixed length to occupy a smaller substrate area. The new geometries are based in part on mathematical analyses that provide the minimum turn radius for which column performance in not degraded. In particular, we find that straight channel segments of sufficient length reduce the required minimum turn radius, enabling compact channel layout when turns and straight segments are combined. The compact geometries are obtained by using turns and straight segments in overlapped or nested arrangements to form pleated or coiled columns.

Laminar and turbulent surgical plume characteristics generated from curved- and straight-blade laparoscopic ultrasonic dissectors.

PubMed

Kim, Fernando J; Sehrt, David; Pompeo, Alexandre; Molina, Wilson R

2014-05-01

To characterize laparoscopic ultrasonic dissector surgical plume emission (laminar or turbulent) and investigate plume settlement time between curved and straight blades. A straight and a curved blade laparoscopic ultrasonic dissector were activated on tissue and in a liquid environment to evaluate plume emission. Plume emission was characterized as either laminar or turbulent and the plume settlement times were compared. Devices were then placed in liquid to observed consistency in the fluid disruption. Two types of plume emission were identified generating different directions of plume: laminar flow causes minimal visual obstruction by directing the aerosol downwards, while turbulent flow directs plume erratically across the cavity. Laminar plume dissipates immediately while turbulent plume reaches a second maximum obstruction approximately 0.3 s after activation and clears after 2 s. Turbulent plume was observed with the straight blade in 10 % of activations, and from the curved blade in 47 % of activations. The straight blade emitted less obstructive plume. Turbulent flow is disruptive to laparoscopic visibility with greater field obstruction and requires longer settling than laminar plume. Ultrasonic dissectors with straight blades have more consistent oscillations and generate more laminar flow compared with curved blades. Surgeons may avoid laparoscope smearing from maximum plume generation depending on blade geometry.

Identification of QTLs for rice grain size using a novel set of chromosomal segment substitution lines derived from Yamadanishiki in the genetic background of Koshihikari

PubMed Central

Okada, Satoshi; Onogi, Akio; Iijima, Ken; Hori, Kiyosumi; Iwata, Hiroyoshi; Yokoyama, Wakana; Suehiro, Miki; Yamasaki, Masanori

2018-01-01

Grain size is important for brewing-rice cultivars, but the genetic basis for this trait is still unclear. This paper aims to identify QTLs for grain size using novel chromosomal segment substitution lines (CSSLs) harboring chromosomal segments from Yamadanishiki, an excellent sake-brewing rice, in the genetic background of Koshihikari, a cooking cultivar. We developed a set of 49 CSSLs. Grain length (GL), grain width (GWh), grain thickness (GT), 100-grain weight (GWt) and days to heading (DTH) were evaluated, and a CSSL-QTL analysis was conducted. Eighteen QTLs for grain size and DTH were identified. Seven (qGL11, qGWh5, qGWh10, qGWt6-2, qGWt10-2, qDTH3, and qDTH6) that were detected in F2 and recombinant inbred lines (RILs) from Koshihikari/Yamadanishiki were validated, suggesting that they are important for large grain size and heading date in Yamadanishiki. Additionally, QTL reanalysis for GWt showed that qGWt10-2 was only detected in early-flowering RILs, while qGWt5 (in the same region as qGWh5) was only detected in late-flowering RILs, suggesting that these QTLs show different responses to the environment. Our study revealed that grain size in the Yamadanishiki cultivar is determined by a complex genetic mechanism. These findings could be useful for the breeding of both cooking and brewing rice. PMID:29875604

Genome-wide scans reveal variants at EDAR predominantly affecting hair straightness in Han Chinese and Uyghur populations.

PubMed

Wu, Sijie; Tan, Jingze; Yang, Yajun; Peng, Qianqian; Zhang, Manfei; Li, Jinxi; Lu, Dongsheng; Liu, Yu; Lou, Haiyi; Feng, Qidi; Lu, Yan; Guan, Yaqun; Zhang, Zhaoxia; Jiao, Yi; Sabeti, Pardis; Krutmann, Jean; Tang, Kun; Jin, Li; Xu, Shuhua; Wang, Sijia

2016-11-01

Hair straightness/curliness is one of the most conspicuous features of human variation and is particularly diverse among populations. A recent genome-wide scan found common variants in the Trichohyalin (TCHH) gene that are associated with hair straightness in Europeans, but different genes might affect this phenotype in other populations. By sampling 2899 Han Chinese, we performed the first genome-wide scan of hair straightness in East Asians, and found EDAR (rs3827760) as the predominant gene (P = 4.67 × 10 -16 ), accounting for 3.66 % of the total variance. The candidate gene approach did not find further significant associations, suggesting that hair straightness may be affected by a large number of genes with subtle effects. Notably, genetic variants associated with hair straightness in Europeans are generally low in frequency in Han Chinese, and vice versa. To evaluate the relative contribution of these variants, we performed a second genome-wide scan in 709 samples from the Uyghur, an admixed population with both eastern and western Eurasian ancestries. In Uyghurs, both EDAR (rs3827760: P = 1.92 × 10 -12 ) and TCHH (rs11803731: P = 1.46 × 10 -3 ) are associated with hair straightness, but EDAR (OR 0.415) has a greater effect than TCHH (OR 0.575). We found no significant interaction between EDAR and TCHH (P = 0.645), suggesting that these two genes affect hair straightness through different mechanisms. Furthermore, haplotype analysis indicates that TCHH is not subject to selection. While EDAR is under strong selection in East Asia, it does not appear to be subject to selection after the admixture in Uyghurs. These suggest that hair straightness is unlikely a trait under selection.

Effects of ipsilateral anterior thigh soft tissue stretching on passive unilateral straight-leg raise.

PubMed

Clark, S; Christiansen, A; Hellman, D F; Hugunin, J W; Hurst, K M

1999-01-01

Randomized 3-group pretest-posttest with blind assessment of outcome. The purpose of this study was to examine the effect of sagittal plane hold-relax exercise applied to the ipsilateral anterior thigh, and prone positioning on passive unilateral straight-leg raise measurements. Straight-leg raising has been viewed as a measurement for hamstring muscle length, but literature suggests that other structures may affect this measurement. Sixty subjects (45 men, 15 women) qualified for inclusion into the study based on a straight-leg raise measurement of < or = 65 degrees. Subjects were randomly assigned to one of three groups: control, static stretch, or sagittal plane hold-relax exercise. Pretest and posttest straight-leg raise measurements of the right lower extremity were performed for each subject. A 1-way ANOVA of the change scores showed a significant difference between groups. A Tukey post hoc analysis of the change scores showed that both treatment groups' means differed significantly from the control group and from each other, with the sagittal plane hold-relax group exhibiting the largest change (mean of 7.8 degrees +/- 2.8 degrees). The results of this study show that sagittal plane hold-relax exercise and passive prone results of this study show that sagittal plane hold-relax and passive prone positioning can significantly increase straight-leg raise range of motion, however the sagittal plane hold-relax stretching of the anterior thigh is more effective than passive prone positioning.

Genetic dissection of a regionally differentiated network for exploratory behavior in Drosophila larvae.

PubMed

Berni, Jimena

2015-05-18

An efficient strategy to explore the environment for available resources involves the execution of random walks where straight line locomotion alternates with changes of direction. This strategy is highly conserved in the animal kingdom, from zooplankton to human hunter-gatherers. Drosophila larvae execute a routine of this kind, performing straight line crawling interrupted at intervals by pause turns that halt crawling and redirect the trajectory of movement. The execution of this routine depends solely on the activity of networks located in the thoracic and abdominal segments of the nervous system, while descending input from the brain serves to modify it in a context-dependent fashion. I used a genetic method to investigate the location and function of the circuitry required for the different elements of exploratory crawling. By using the Slit-Robo axon guidance pathway to target neuronal midline crossing defects selectively to particular regions of the thoracic and abdominal networks, it has been possible to define at least three functions required for the performance of the exploratory routine: (1) symmetrical outputs in thoracic and abdominal segments that generate the crawls; (2) asymmetrical output that is uniquely initiated in the thoracic segments and generates the turns; and (3) an intermittent interruption to crawling that determines the time-dependent transition between crawls and turns. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Genetic Dissection of a Regionally Differentiated Network for Exploratory Behavior in Drosophila Larvae

PubMed Central

Berni, Jimena

2015-01-01

Summary An efficient strategy to explore the environment for available resources involves the execution of random walks where straight line locomotion alternates with changes of direction. This strategy is highly conserved in the animal kingdom, from zooplankton to human hunter-gatherers [1–8]. Drosophila larvae execute a routine of this kind, performing straight line crawling interrupted at intervals by pause turns that halt crawling and redirect the trajectory of movement [9–11]. The execution of this routine depends solely on the activity of networks located in the thoracic and abdominal segments of the nervous system, while descending input from the brain serves to modify it in a context-dependent fashion [9]. I used a genetic method to investigate the location and function of the circuitry required for the different elements of exploratory crawling. By using the Slit-Robo axon guidance pathway to target neuronal midline crossing defects selectively to particular regions of the thoracic and abdominal networks, it has been possible to define at least three functions required for the performance of the exploratory routine: (1) symmetrical outputs in thoracic and abdominal segments that generate the crawls; (2) asymmetrical output that is uniquely initiated in the thoracic segments and generates the turns; and (3) an intermittent interruption to crawling that determines the time-dependent transition between crawls and turns. PMID:25959962

Subjective Straight Ahead Orientation in Microgravity

NASA Technical Reports Server (NTRS)

Clement, G.; Reschke, M. F.; Wood, S. J.

2015-01-01

This joint ESA NASA study will address adaptive changes in spatial orientation related to the subjective straight ahead and the use of a vibrotactile sensory aid to reduce perceptual errors. The study will be conducted before and after long-duration expeditions to the International Space Station (ISS) to examine how spatial processing of target location is altered following exposure to microgravity. This study addresses the sensorimotor research gap to "determine the changes in sensorimotor function over the course of a mission and during recovery after landing."

Segmenting overlapping nano-objects in atomic force microscopy image

NASA Astrophysics Data System (ADS)

Wang, Qian; Han, Yuexing; Li, Qing; Wang, Bing; Konagaya, Akihiko

2018-01-01

Recently, techniques for nanoparticles have rapidly been developed for various fields, such as material science, medical, and biology. In particular, methods of image processing have widely been used to automatically analyze nanoparticles. A technique to automatically segment overlapping nanoparticles with image processing and machine learning is proposed. Here, two tasks are necessary: elimination of image noises and action of the overlapping shapes. For the first task, mean square error and the seed fill algorithm are adopted to remove noises and improve the quality of the original image. For the second task, four steps are needed to segment the overlapping nanoparticles. First, possibility split lines are obtained by connecting the high curvature pixels on the contours. Second, the candidate split lines are classified with a machine learning algorithm. Third, the overlapping regions are detected with the method of density-based spatial clustering of applications with noise (DBSCAN). Finally, the best split lines are selected with a constrained minimum value. We give some experimental examples and compare our technique with two other methods. The results can show the effectiveness of the proposed technique.

Straight type culvert headwall, Culvert No. 105 Inlet, oblique view, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Straight type culvert headwall, Culvert No. 105 Inlet, oblique view, view to northeast - Route No. 1-Overton-Lake Mead Road, Culverts and Headwalls, 6 miles south of Overton, Overton, Clark County, NV

Straight on view of northeast side of Olive Switching Station ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Straight on view of northeast side of Olive Switching Station from north side of San Fernando Road facing southwest - Olive Switching Station, 13355 San Fernando Road, Los Angeles, Los Angeles County, CA

Innovative visualization and segmentation approaches for telemedicine

NASA Astrophysics Data System (ADS)

Nguyen, D.; Roehrig, Hans; Borders, Marisa H.; Fitzpatrick, Kimberly A.; Roveda, Janet

2014-09-01

In health care applications, we obtain, manage, store and communicate using high quality, large volume of image data through integrated devices. In this paper we propose several promising methods that can assist physicians in image data process and communication. We design a new semi-automated segmentation approach for radiological images, such as CT and MRI to clearly identify the areas of interest. This approach combines the advantages from both the region-based method and boundary-based methods. It has three key steps compose: coarse segmentation by using fuzzy affinity and homogeneity operator, image division and reclassification using the Voronoi Diagram, and refining boundary lines using the level set model.

Podokinetic Stimulation Causes Shifts in Perception of Straight Ahead

PubMed Central

Scott, John T.; Lohnes, Corey A.; Horak, Fay B.; Earhart, Gammon M.

2011-01-01

Podokinetic after-rotation (PKAR) is a phenomenon in which subjects inadvertently rotate when instructed to step in place after a period of walking on a rotating treadmill. PKAR has been shown to transfer between different forms of locomotion, but has not been tested in a non-locomotor task. We conducted two experiments to assess effects of PKAR on perception of subjective straight ahead and on quiet standing posture. Twenty-one healthy young right-handed subjects pointed to what they perceived as their subjective straight ahead with a laser pointer while they were recorded by a motion capture system both before and after a training period on the rotating treadmill. Subjects performed the pointing task while standing, sitting on a chair without a back, and a chair with a back. After the training period, subjects demonstrated a significant shift in subjective straight ahead, pointing an average of 29.1 ± 10.6 degrees off of center. The effect was direction-specific, depending on whether subjects had trained in the clockwise or counter-clockwise direction. Postures that limited subjects’ ability to rotate the body in space resulted in reduction, but not elimination, of the effect. The effect was present in quiet standing and even in sitting postures where locomotion was not possible. The robust transfer of PKAR to non-locomotor tasks, and across locomotor forms as demonstrated previously, is in contrast to split-belt adaptations that show limited transfer. We propose that, unlike split-belt adaptations, podokinetic adaptations are mediated at supraspinal, spatial orientation areas that influences spinal-level circuits for locomotion. PMID:21076818

Say It Straight: Adolescent Substance Abuse Prevention Training.

ERIC Educational Resources Information Center

Englander-Golden, Paula; And Others

Patterns of drug use among teenagers indicate they are highly influenced by peers. To examine the influence of Say It Straight, an alcohol/drug abuse prevention program aimed at teaching adolescents to deal with peer pressure, sixth, seventh and eighth graders (N=509) created and role played situations in which they wanted to say "no" to…

Stress Intensity Factors of Semi-Circular Bend Specimens with Straight-Through and Chevron Notches

NASA Astrophysics Data System (ADS)

Ayatollahi, M. R.; Mahdavi, E.; Alborzi, M. J.; Obara, Y.

2016-04-01

Semi-circular bend specimen is one of the useful test specimens for determining fracture toughness of rock and geo-materials. Generally, in rock test specimens, initial cracks are produced in two shapes: straight-edge cracks and chevron notches. In this study, the minimum dimensionless stress intensity factors of semi-circular bend specimen (SCB) with straight-through and chevron notches are calculated. First, using finite element analysis, a suitable relation for the dimensionless stress intensity factor of SCB with straight-through crack is presented based on the normalized crack length and half-distance between supports. For evaluating the validity and accuracy of this relation, the obtained results are then compared with numerical and experimental results reported in the literature. Subsequently, by performing some experiments and also finite element analysis of the SCB specimen with chevron notch, the minimum dimensionless stress intensity factor of this specimen is obtained. Using the new equation for the dimensionless stress intensity factor of SCB with straight-through crack and an analytical method, i.e., Bluhm's slice synthesis method, the minimum (critical) dimensionless stress intensity factor of chevron notched semi-circular bend specimens is calculated. Good agreement is observed between the results of two mentioned methods.

Moving vehicles segmentation based on Gaussian motion model

NASA Astrophysics Data System (ADS)

Zhang, Wei; Fang, Xiang Z.; Lin, Wei Y.

2005-07-01

Moving objects segmentation is a challenge in computer vision. This paper focuses on the segmentation of moving vehicles in dynamic scene. We analyses the psychology of human vision and present a framework for segmenting moving vehicles in the highway. The proposed framework consists of two parts. Firstly, we propose an adaptive background update method in which the background is updated according to the change of illumination conditions and thus can adapt to the change of illumination sensitively. Secondly, we construct a Gaussian motion model to segment moving vehicles, in which the motion vectors of the moving pixels are modeled as a Gaussian model and an on-line EM algorithm is used to update the model. The Gaussian distribution of the adaptive model is elevated to determine which moving vectors result from moving vehicles and which from other moving objects such as waving trees. Finally, the pixels with motion vector result from the moving vehicles are segmented. Experimental results of several typical scenes show that the proposed model can detect the moving vehicles correctly and is immune from influence of the moving objects caused by the waving trees and the vibration of camera.

Interactive Tooth Separation from Dental Model Using Segmentation Field

PubMed Central

2016-01-01

Tooth segmentation on dental model is an essential step of computer-aided-design systems for orthodontic virtual treatment planning. However, fast and accurate identifying cutting boundary to separate teeth from dental model still remains a challenge, due to various geometrical shapes of teeth, complex tooth arrangements, different dental model qualities, and varying degrees of crowding problems. Most segmentation approaches presented before are not able to achieve a balance between fine segmentation results and simple operating procedures with less time consumption. In this article, we present a novel, effective and efficient framework that achieves tooth segmentation based on a segmentation field, which is solved by a linear system defined by a discrete Laplace-Beltrami operator with Dirichlet boundary conditions. A set of contour lines are sampled from the smooth scalar field, and candidate cutting boundaries can be detected from concave regions with large variations of field data. The sensitivity to concave seams of the segmentation field facilitates effective tooth partition, as well as avoids obtaining appropriate curvature threshold value, which is unreliable in some case. Our tooth segmentation algorithm is robust to dental models with low quality, as well as is effective to dental models with different levels of crowding problems. The experiments, including segmentation tests of varying dental models with different complexity, experiments on dental meshes with different modeling resolutions and surface noises and comparison between our method and the morphologic skeleton segmentation method are conducted, thus demonstrating the effectiveness of our method. PMID:27532266

Assessment of the Old Red Rock Indian Line Sycamore Tree, Lake Red Rock, Marion County, Iowa

DTIC Science & Technology

1992-01-01

miles, when reduced to a straight line , from the junction of the White Breast and Des Moines (Stiles 1911:4). George W. Harrison was instructed to...AD-A255 372 Assessment of the Old Red Rock Indian Line Sycamore Tree, Lake Red Rock, Marion County, Iowa DACW25-92-M-0414 by Leah D. Rogers Project...portion of tree 22 9. Map showing location of Red Rock line within treaty cession area of 23 1842 10. Portion of 1844 map showing incorrect placement of

Radiographic comparison of apical root resorption after orthodontic treatment between bidimensional and Roth straight-wire techniques

PubMed Central

Zawawi, Khalid H; Malki, Ghadah A

2014-01-01

Objective: The aim of this study was to compare the amount of root resorption after orthodontic treatment between the bidimensional and the Roth straight-wire techniques. Another objective was to compare the amount of root resorption in the whole sample studied and record the prevalence of root resorption. Materials and Methods: The sample consisted of 40 patients (age ranged between 11 and 18 years) with Angle Class II division 1 malocclusions, treated nonextraction. Twenty patients were treated with bidimensional technique and 20 with a 0.018-inch Roth straight-wire technique. Root lengths of the maxillary incisors were measured on pre- and post-treatment periapical radiographs. Results: The results demonstrated that the bidimensional and Roth straight-wire groups showed significant root resorption after treatment, 1.11 (0.17) and 0.86 (0.05), respectively, P < 0.001. When comparing the amount of root shortening between the bidimensional and Roth straight-wire groups, there was no significant difference between the mean change from pre- to post-treatment between bidimensional group (mean = 1.00 ± 1.34) and Roth straight-wire group (mean = 0.88 ± 0.86), P = 0.63. Considering the whole sample, there was no root resoprtion in 32.5% of the analysed teeth. There was only mild resorption in 56.2%, moderate in 8.8% and severe in only 2.5% of the teeth. Conclusions: Treatment with the bidimensional technique did not produce an increase in the amount of root resorption. The prevalence and amount of root resorption was similar between bidimensional and Roth straight-wire techniques. PMID:25426453

Radiographic comparison of apical root resorption after orthodontic treatment between bidimensional and Roth straight-wire techniques.

PubMed

Zawawi, Khalid H; Malki, Ghadah A

2014-10-01

The aim of this study was to compare the amount of root resorption after orthodontic treatment between the bidimensional and the Roth straight-wire techniques. Another objective was to compare the amount of root resorption in the whole sample studied and record the prevalence of root resorption. The sample consisted of 40 patients (age ranged between 11 and 18 years) with Angle Class II division 1 malocclusions, treated nonextraction. Twenty patients were treated with bidimensional technique and 20 with a 0.018-inch Roth straight-wire technique. Root lengths of the maxillary incisors were measured on pre- and post-treatment periapical radiographs. The results demonstrated that the bidimensional and Roth straight-wire groups showed significant root resorption after treatment, 1.11 (0.17) and 0.86 (0.05), respectively, P < 0.001. When comparing the amount of root shortening between the bidimensional and Roth straight-wire groups, there was no significant difference between the mean change from pre- to post-treatment between bidimensional group (mean = 1.00 ± 1.34) and Roth straight-wire group (mean = 0.88 ± 0.86), P = 0.63. Considering the whole sample, there was no root resoprtion in 32.5% of the analysed teeth. There was only mild resorption in 56.2%, moderate in 8.8% and severe in only 2.5% of the teeth. Treatment with the bidimensional technique did not produce an increase in the amount of root resorption. The prevalence and amount of root resorption was similar between bidimensional and Roth straight-wire techniques.

Straight chiropractic philosophy as a barrier to Medicare compliance: a discussion of 5 incongruent issues

PubMed Central

Seaman, David R.; Soltys, Jonathan R.

2013-01-01

Objective The purpose of this commentary is to discuss potential 5 factors within straight chiropractic philosophy and practice that may prevent Medicare compliance. Discussion The national Medicare Benefit Policy Manual and the Florida Local Coverage Determination were reviewed to identify documentation and conceptual issues regarding chiropractic practice. Five Medicare positions were contrasted with tenets of straight chiropractic philosophy. Based on Medicare’s documentation requirements, Medicare defines subluxation and chiropractic practice from the perspective of treating spinal pain and related functional disability. In contrast, traditional straight chiropractic philosophy is not based on the treatment of spinal pain and disability or other symptomatic presentations. In this context, 5 potential areas of conflict are discussed. Conclusion The Medicare version of chiropractic practice is not consistent with traditional straight chiropractic philosophy, which may play a role in preventing Medicare compliance. The chiropractic profession may need to consider the fashion in which “philosophy” as it relates to technique and practice is presented to students and doctors to facilitate compliance with the documentation requirements of Medicare. PMID:25067928

Three-Axis Ground Reaction Force Distribution during Straight Walking.

PubMed

Hori, Masataka; Nakai, Akihito; Shimoyama, Isao

2017-10-24

We measured the three-axis ground reaction force (GRF) distribution during straight walking. Small three-axis force sensors composed of rubber and sensor chips were fabricated and calibrated. After sensor calibration, 16 force sensors were attached to the left shoe. The three-axis force distribution during straight walking was measured, and the local features of the three-axis force under the sole of the shoe were analyzed. The heel area played a role in receiving the braking force, the base area of the fourth and fifth toes applied little vertical or shear force, the base area of the second and third toes generated a portion of the propulsive force and received a large vertical force, and the base area of the big toe helped move the body's center of mass to the other foot. The results demonstrate that measuring the three-axis GRF distribution is useful for a detailed analysis of bipedal locomotion.

Image Segmentation of Historical Handwriting from Palm Leaf Manuscripts

NASA Astrophysics Data System (ADS)

Surinta, Olarik; Chamchong, Rapeeporn

Palm leaf manuscripts were one of the earliest forms of written media and were used in Southeast Asia to store early written knowledge about subjects such as medicine, Buddhist doctrine and astrology. Therefore, historical handwritten palm leaf manuscripts are important for people who like to learn about historical documents, because we can learn more experience from them. This paper presents an image segmentation of historical handwriting from palm leaf manuscripts. The process is composed of three steps: 1) background elimination to separate text and background by Otsu's algorithm 2) line segmentation and 3) character segmentation by histogram of image. The end result is the character's image. The results from this research may be applied to optical character recognition (OCR) in the future.

Thermal Buckling of Straight Tracks : Fundamentals, Analyses, and Preventive Measures

DOT National Transportation Integrated Search

1978-09-01

This report, written mainly for the practicing railroad engineer, explains the phenomenon of thermal buckling of straight tracks, shows how to analyze it, and describes measures for preventing it. Following an introductory discussion of track bucklin...

An interesting case of straight back syndrome and review of the literature.

PubMed

Soleti, Pavan; Wilson, Bivin; Vijayakumar, Arani Rajabathar; Chakravarthi, Paulraj Ignatius Sudhakar; Reddy, Chilakala Gopinath

2016-01-01

Straight back syndrome is characterized by loss of the normal upper thoracic kyphosis, leading to a reduced anteroposterior diameter and squashing of the heart. Most patients are asymptomatic; if symptomatic, chest pain and palpitations are most common. On examination, the abnormal clinical findings simulate organic heart disease that needs to be ruled out by echocardiography and cardiac catheterization. A lateral chest radiograph is diagnostic. This condition is commonly associated with mitral valve prolapse and bicuspid aortic valve. We describe an interesting case of straight back syndrome with all the classic and rarely reported clinical findings. © The Author(s) 2014.

Polyethylene composites containing a phase change material having a C14 straight chain hydrocarbon

DOEpatents

Salyer, Ival O.

1987-01-01

A composite useful in thermal energy storage, said composite being formed of a polyethylene matrix having a straight chain alkyl hydrocarbon incorporated therein, said polyethylene being crosslinked to such a degree that said polyethylene matrix is form stable and said polyethylene matrix is capable of absorbing at least 10% by weight of said straight chain alkyl hydrocarbon; the composite is useful in forming pellets or sheets having thermal energy storage characteristics.

Controversies Surrounding Segments and Parasegments in Onychophora: Insights from the Expression Patterns of Four “Segment Polarity Genes” in the Peripatopsid Euperipatoides rowelli

PubMed Central

Franke, Franziska Anni; Mayer, Georg

2014-01-01

Arthropods typically show two types of segmentation: the embryonic parasegments and the adult segments that lie out of register with each other. Such a dual nature of body segmentation has not been described from Onychophora, one of the closest arthropod relatives. Hence, it is unclear whether onychophorans have segments, parasegments, or both, and which of these features was present in the last common ancestor of Onychophora and Arthropoda. To address this issue, we analysed the expression patterns of the “segment polarity genes” engrailed, cubitus interruptus, wingless and hedgehog in embryos of the onychophoran Euperipatoides rowelli. Our data revealed that these genes are expressed in repeated sets with a specific anterior-to-posterior order along the body in embryos of E. rowelli. In contrast to arthropods, the expression occurs after the segmental boundaries have formed. Moreover, the initial segmental furrow retains its position within the engrailed domain throughout development, whereas no new furrow is formed posterior to this domain. This suggests that no re-segmentation of the embryo occurs in E. rowelli. Irrespective of whether or not there is a morphological or genetic manifestation of parasegments in Onychophora, our data clearly show that parasegments, even if present, cannot be regarded as the initial metameric units of the onychophoran embryo, because the expression of key genes that define the parasegmental boundaries in arthropods occurs after the segmental boundaries have formed. This is in contrast to arthropods, in which parasegments rather than segments are the initial metameric units of the embryo. Our data further revealed that the expression patterns of “segment polarity genes” correspond to organogenesis rather than segment formation. This is in line with the concept of segmentation as a result of concerted evolution of individual periodic structures rather than with the interpretation of ‘segments’ as holistic units. PMID

49 CFR 192.719 - Transmission lines: Testing of repairs.

Code of Federal Regulations, 2010 CFR

2010-10-01

... pipe before it is installed. (b) Testing of repairs made by welding. Each repair made by welding in... 49 Transportation 3 2010-10-01 2010-10-01 false Transmission lines: Testing of repairs. 192.719... Transmission lines: Testing of repairs. (a) Testing of replacement pipe. If a segment of transmission line is...

Modification to area navigation equipment for instrument two-segment approaches

NASA Technical Reports Server (NTRS)

1975-01-01

A two-segment aircraft landing approach concept utilizing an area random navigation (RNAV) system to execute the two-segment approach and eliminate the requirements for co-located distance measuring equipment (DME) was investigated. This concept permits non-precision approaches to be made to runways not equipped with ILS systems, down to appropriate minima. A hardware and software retrofit kit for the concept was designed, built, and tested on a DC-8-61 aircraft for flight evaluation. A two-segment approach profile and piloting procedure for that aircraft that will provide adequate safety margin under adverse weather, in the presence of system failures, and with the occurrence of an abused approach, was also developed. The two-segment approach procedure and equipment was demonstrated to line pilots under conditions which are representative of those encountered in air carrier service.

Modeling and experimental characterization of electromigration in interconnect trees

NASA Astrophysics Data System (ADS)

Thompson, C. V.; Hau-Riege, S. P.; Andleigh, V. K.

1999-11-01

Most modeling and experimental characterization of interconnect reliability is focussed on simple straight lines terminating at pads or vias. However, laid-out integrated circuits often have interconnects with junctions and wide-to-narrow transitions. In carrying out circuit-level reliability assessments it is important to be able to assess the reliability of these more complex shapes, generally referred to as `trees.' An interconnect tree consists of continuously connected high-conductivity metal within one layer of metallization. Trees terminate at diffusion barriers at vias and contacts, and, in the general case, can have more than one terminating branch when they include junctions. We have extended the understanding of `immortality' demonstrated and analyzed for straight stud-to-stud lines, to trees of arbitrary complexity. This leads to a hierarchical approach for identifying immortal trees for specific circuit layouts and models for operation. To complete a circuit-level-reliability analysis, it is also necessary to estimate the lifetimes of the mortal trees. We have developed simulation tools that allow modeling of stress evolution and failure in arbitrarily complex trees. We are testing our models and simulations through comparisons with experiments on simple trees, such as lines broken into two segments with different currents in each segment. Models, simulations and early experimental results on the reliability of interconnect trees are shown to be consistent.

49 CFR 192.485 - Remedial measures: Transmission lines.

Code of Federal Regulations, 2011 CFR

2011-10-01

... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Requirements for Corrosion Control § 192.485 Remedial measures: Transmission lines. (a) General corrosion. Each segment of transmission line with general corrosion and with a remaining wall thickness less than that required for the...

49 CFR 192.485 - Remedial measures: Transmission lines.

Code of Federal Regulations, 2012 CFR

2012-10-01

... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Requirements for Corrosion Control § 192.485 Remedial measures: Transmission lines. (a) General corrosion. Each segment of transmission line with general corrosion and with a remaining wall thickness less than that required for the...

49 CFR 192.485 - Remedial measures: Transmission lines.

Code of Federal Regulations, 2014 CFR

2014-10-01

... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Requirements for Corrosion Control § 192.485 Remedial measures: Transmission lines. (a) General corrosion. Each segment of transmission line with general corrosion and with a remaining wall thickness less than that required for the...

49 CFR 192.485 - Remedial measures: Transmission lines.

Code of Federal Regulations, 2013 CFR

2013-10-01

... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Requirements for Corrosion Control § 192.485 Remedial measures: Transmission lines. (a) General corrosion. Each segment of transmission line with general corrosion and with a remaining wall thickness less than that required for the...

Android application for handwriting segmentation using PerTOHS theory

NASA Astrophysics Data System (ADS)

Akouaydi, Hanen; Njah, Sourour; Alimi, Adel M.

2017-03-01

The paper handles the problem of segmentation of handwriting on mobile devices. Many applications have been developed in order to facilitate the recognition of handwriting and to skip the limited numbers of keys in keyboards and try to introduce a space of drawing for writing instead of using keyboards. In this one, we will present a mobile theory for the segmentation of for handwriting uses PerTOHS theory, Perceptual Theory of On line Handwriting Segmentation, where handwriting is defined as a sequence of elementary and perceptual codes. In fact, the theory analyzes the written script and tries to learn the handwriting visual codes features in order to generate new ones via the generated perceptual sequences. To get this classification we try to apply the Beta-elliptic model, fuzzy detector and also genetic algorithms in order to get the EPCs (Elementary Perceptual Codes) and GPCs (Global Perceptual Codes) that composed the script. So, we will present our Android application M-PerTOHS for segmentation of handwriting.

Off-shell amplitudes as boundary integrals of analytically continued Wilson line slope

NASA Astrophysics Data System (ADS)

Kotko, P.; Serino, M.; Stasto, A. M.

2016-08-01

One of the methods to calculate tree-level multi-gluon scattering amplitudes is to use the Berends-Giele recursion relation involving off-shell currents or off-shell amplitudes, if working in the light cone gauge. As shown in recent works using the light-front perturbation theory, solutions to these recursions naturally collapse into gauge invariant and gauge-dependent components, at least for some helicity configurations. In this work, we show that such structure is helicity independent and emerges from analytic properties of matrix elements of Wilson line operators, where the slope of the straight gauge path is shifted in a certain complex direction. This is similar to the procedure leading to the Britto-Cachazo-Feng-Witten (BCFW) recursion, however we apply a complex shift to the Wilson line slope instead of the external momenta. While in the original BCFW procedure the boundary integrals over the complex shift vanish for certain deformations, here they are non-zero and are equal to the off-shell amplitudes. The main result can thus be summarized as follows: we derive a decomposition of a helicity-fixed off-shell current into gauge invariant component given by a matrix element of a straight Wilson line plus a reminder given by a sum of products of gauge invariant and gauge dependent quantities. We give several examples realizing this relation, including the five-point next-to-MHV helicity configuration.

Inhibition of Bacterial Rna Polymerase by Streptolydigin: Stabilization of A Straight-Bridge-Helix Active-Center Conformation

PubMed Central

Tuske, Steven; Sarafianos, Stefan G.; Wang, Xinyue; Hudson, Brian; Sineva, Elena; Mukhopadhyay, Jayanta; Birktoft, Jens J.; Leroy, Olivier; Ismail, Sajida; Clark, Arthur D.; Dharia, Chhaya; Napoli, Andrew; Laptenko, Oleg; Lee, Jookyung; Borukhov, Sergei; Ebright, Richard H.; Arnold, Eddy

2009-01-01

We define the target, mechanism, and structural basis of inhibition of bacterial RNA polymerase (RNAP) by the tetramic-acid antibiotic streptolydigin (Stl). Stl binds to a site adjacent to, but not overlapping, the RNAP active center and stabilizes an RNAP-active-center conformational state with a straight bridge helix. The results provide direct support for the proposals that alternative straight-bridge-helix and bent-bridge-helix RNAP-active-center conformations exist, and that cycling between straight-bridge-helix and bent-bridge-helix RNAP-active-center conformations is required for RNAP function. The results set bounds on models for RNAP function and suggest strategies for design of novel antibacterial agents. PMID:16122422

Unsupervised motion-based object segmentation refined by color

NASA Astrophysics Data System (ADS)

Piek, Matthijs C.; Braspenning, Ralph; Varekamp, Chris

2003-06-01

. The presented method has no problems with bifurcations. For the pixel resolution segmentation itself we reclassify pixels such that we optimize an error norm which favour similarly coloured regions and straight edges. SEGMENTATION MEASURE To assist in the evaluation of the proposed algorithm we developed a quality metric. Because the problem does not have an exact specification, we decided to define a ground truth output which we find desirable for a given input. We define the measure for the segmentation quality as being how different the segmentation is from the ground truth. Our measure enables us to evaluate oversegmentation and undersegmentation seperately. Also, it allows us to evaluate which parts of a frame suffer from oversegmentation or undersegmentation. The proposed algorithm has been tested on several typical sequences. CONCLUSIONS In this abstract we presented a new video segmentation method which performs well in the segmentation of multiple independently moving foreground objects from each other and the background. It combines the strong points of both colour and motion segmentation in the way we expected. One of the weak points is that the segmentation method suffers from undersegmentation when adjacent objects display similar motion. In sequences with detailed backgrounds the segmentation will sometimes display noisy edges. Apart from these results, we think that some of the techniques, and in particular the K-regions technique, may be useful for other two-dimensional data segmentation problems.

Detection of the power lines in UAV remote sensed images using spectral-spatial methods.

PubMed

Bhola, Rishav; Krishna, Nandigam Hari; Ramesh, K N; Senthilnath, J; Anand, Gautham

2018-01-15

In this paper, detection of the power lines on images acquired by Unmanned Aerial Vehicle (UAV) based remote sensing is carried out using spectral-spatial methods. Spectral clustering was performed using Kmeans and Expectation Maximization (EM) algorithm to classify the pixels into the power lines and non-power lines. The spectral clustering methods used in this study are parametric in nature, to automate the number of clusters Davies-Bouldin index (DBI) is used. The UAV remote sensed image is clustered into the number of clusters determined by DBI. The k clustered image is merged into 2 clusters (power lines and non-power lines). Further, spatial segmentation was performed using morphological and geometric operations, to eliminate the non-power line regions. In this study, UAV images acquired at different altitudes and angles were analyzed to validate the robustness of the proposed method. It was observed that the EM with spatial segmentation (EM-Seg) performed better than the Kmeans with spatial segmentation (Kmeans-Seg) on most of the UAV images. Copyright © 2017 Elsevier Ltd. All rights reserved.

Segmental duplications and evolutionary plasticity at tumor chromosome break-prone regions

PubMed Central

Darai-Ramqvist, Eva; Sandlund, Agneta; Müller, Stefan; Klein, George; Imreh, Stefan; Kost-Alimova, Maria

2008-01-01

We have previously found that the borders of evolutionarily conserved chromosomal regions often coincide with tumor-associated deletion breakpoints within human 3p12-p22. Moreover, a detailed analysis of a frequently deleted region at 3p21.3 (CER1) showed associations between tumor breaks and gene duplications. We now report on the analysis of 54 chromosome 3 breaks by multipoint FISH (mpFISH) in 10 carcinoma-derived cell lines. The centromeric region was broken in five lines. In lines with highly complex karyotypes, breaks were clustered near known fragile sites, FRA3B, FRA3C, and FRA3D (three lines), and in two other regions: 3p12.3-p13 (∼75 Mb position) and 3q21.3-q22.1 (∼130 Mb position) (six lines). All locations are shown based on NCBI Build 36.1 human genome sequence. The last two regions participated in three of four chromosome 3 inversions during primate evolution. Regions at 75, 127, and 131 Mb positions carry a large (∼250 kb) segmental duplication (tumor break-prone segmental duplication [TBSD]). TBSD homologous sequences were found at 15 sites on different chromosomes. They were located within bands frequently involved in carcinoma-associated breaks. Thirteen of them have been involved in inversions during primate evolution; 10 were reused by breaks during mammalian evolution; 14 showed copy number polymorphism in man. TBSD sites showed an increase in satellite repeats, retrotransposed sequences, and other segmental duplications. We propose that the instability of these sites stems from specific organization of the chromosomal region, associated with location at a boundary between different CG-content isochores and with the presence of TBSDs and “instability elements,” including satellite repeats and retroviral sequences. PMID:18230801

Segmental duplications and evolutionary plasticity at tumor chromosome break-prone regions.

PubMed

Darai-Ramqvist, Eva; Sandlund, Agneta; Müller, Stefan; Klein, George; Imreh, Stefan; Kost-Alimova, Maria

2008-03-01

We have previously found that the borders of evolutionarily conserved chromosomal regions often coincide with tumor-associated deletion breakpoints within human 3p12-p22. Moreover, a detailed analysis of a frequently deleted region at 3p21.3 (CER1) showed associations between tumor breaks and gene duplications. We now report on the analysis of 54 chromosome 3 breaks by multipoint FISH (mpFISH) in 10 carcinoma-derived cell lines. The centromeric region was broken in five lines. In lines with highly complex karyotypes, breaks were clustered near known fragile sites, FRA3B, FRA3C, and FRA3D (three lines), and in two other regions: 3p12.3-p13 ( approximately 75 Mb position) and 3q21.3-q22.1 ( approximately 130 Mb position) (six lines). All locations are shown based on NCBI Build 36.1 human genome sequence. The last two regions participated in three of four chromosome 3 inversions during primate evolution. Regions at 75, 127, and 131 Mb positions carry a large ( approximately 250 kb) segmental duplication (tumor break-prone segmental duplication [TBSD]). TBSD homologous sequences were found at 15 sites on different chromosomes. They were located within bands frequently involved in carcinoma-associated breaks. Thirteen of them have been involved in inversions during primate evolution; 10 were reused by breaks during mammalian evolution; 14 showed copy number polymorphism in man. TBSD sites showed an increase in satellite repeats, retrotransposed sequences, and other segmental duplications. We propose that the instability of these sites stems from specific organization of the chromosomal region, associated with location at a boundary between different CG-content isochores and with the presence of TBSDs and "instability elements," including satellite repeats and retroviral sequences.

"Say It Straight" Training with Mothers in Chemical Dependency Treatment.

ERIC Educational Resources Information Center

Englander-Golden, Paula; Gitchel, Elizabeth; Henderson, Craig E.; Golden, David E.; Hardy, Rebecca

2002-01-01

Evaluates effectiveness of "Say It Straight" communication training with 36 mothers in residential chemical dependency treatment. Self-reported, disempowering behaviors showed highly significant decreases after SIS training, and empowering behaviors showed significant increases. Results indicate this training is an important addition to…

Comparison of segmentation algorithms for fluorescence microscopy images of cells.

PubMed

Dima, Alden A; Elliott, John T; Filliben, James J; Halter, Michael; Peskin, Adele; Bernal, Javier; Kociolek, Marcin; Brady, Mary C; Tang, Hai C; Plant, Anne L

2011-07-01

The analysis of fluorescence microscopy of cells often requires the determination of cell edges. This is typically done using segmentation techniques that separate the cell objects in an image from the surrounding background. This study compares segmentation results from nine different segmentation techniques applied to two different cell lines and five different sets of imaging conditions. Significant variability in the results of segmentation was observed that was due solely to differences in imaging conditions or applications of different algorithms. We quantified and compared the results with a novel bivariate similarity index metric that evaluates the degree of underestimating or overestimating a cell object. The results show that commonly used threshold-based segmentation techniques are less accurate than k-means clustering with multiple clusters. Segmentation accuracy varies with imaging conditions that determine the sharpness of cell edges and with geometric features of a cell. Based on this observation, we propose a method that quantifies cell edge character to provide an estimate of how accurately an algorithm will perform. The results of this study will assist the development of criteria for evaluating interlaboratory comparability. Published 2011 Wiley-Liss, Inc.

Efficient Lane Boundary Detection with Spatial-Temporal Knowledge Filtering

PubMed Central

Nan, Zhixiong; Wei, Ping; Xu, Linhai; Zheng, Nanning

2016-01-01

Lane boundary detection technology has progressed rapidly over the past few decades. However, many challenges that often lead to lane detection unavailability remain to be solved. In this paper, we propose a spatial-temporal knowledge filtering model to detect lane boundaries in videos. To address the challenges of structure variation, large noise and complex illumination, this model incorporates prior spatial-temporal knowledge with lane appearance features to jointly identify lane boundaries. The model first extracts line segments in video frames. Two novel filters—the Crossing Point Filter (CPF) and the Structure Triangle Filter (STF)—are proposed to filter out the noisy line segments. The two filters introduce spatial structure constraints and temporal location constraints into lane detection, which represent the spatial-temporal knowledge about lanes. A straight line or curve model determined by a state machine is used to fit the line segments to finally output the lane boundaries. We collected a challenging realistic traffic scene dataset. The experimental results on this dataset and other standard dataset demonstrate the strength of our method. The proposed method has been successfully applied to our autonomous experimental vehicle. PMID:27529248

Multioriented and curved text lines extraction from Indian documents.

PubMed

Pal, U; Roy, Partha Pratim

2004-08-01

There are printed artistic documents where text lines of a single page may not be parallel to each other. These text lines may have different orientations or the text lines may be curved shapes. For the optical character recognition (OCR) of these documents, we need to extract such lines properly. In this paper, we propose a novel scheme, mainly based on the concept of water reservoir analogy, to extract individual text lines from printed Indian documents containing multioriented and/or curve text lines. A reservoir is a metaphor to illustrate the cavity region of a character where water can be stored. In the proposed scheme, at first, connected components are labeled and identified either as isolated or touching. Next, each touching component is classified either straight type (S-type) or curve type (C-type), depending on the reservoir base-area and envelope points of the component. Based on the type (S-type or C-type) of a component two candidate points are computed from each touching component. Finally, candidate regions (neighborhoods of the candidate points) of the candidate points of each component are detected and after analyzing these candidate regions, components are grouped to get individual text lines.

New airfoil sections for straight bladed turbine

NASA Astrophysics Data System (ADS)

Boumaza, B.

1987-07-01

A theoretical investigation of aerodynamic performance for vertical axis Darrieus wind turbine with new airfoils sections is carried out. The blade section aerodynamics characteristics are determined from turbomachines cascade model. The model is also adapted to the vertical Darrieus turbine for the performance prediction of the machine. In order to choose appropriate value of zero-lift-drag coefficient in calculation, an analytical expression is introduced as function of chord-radius ratio and Reynolds numbers. New airfoils sections are proposed and analyzed for straight-bladed turbine.

146. DETAIL VIEW, LOOKING STRAIGHT ON, OF CAST IRON LAMP ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

146. DETAIL VIEW, LOOKING STRAIGHT ON, OF CAST IRON LAMP STANDARD. THIS AND OTHER LAMP STANDARDS WERE REMOVED FROM THE LAMP COLUMNS ON THE PARAPET WALLS DURING WORLD WAR II AND STORED INSIDE THE DAM (January 1991) - Coolidge Dam, Gila River, Peridot, Gila County, AZ

21 CFR 82.5 - General specifications for straight colors.

Code of Federal Regulations, 2010 CFR

2010-04-01

... (in dilute HCl) (as BaCl2), not more than 0.05 percent. ... specifications: (1) In the case of a straight color listed in subpart B: (i) Lead (as Pb), not more than 0.001 percent. (ii) Arsenic (as As2O3), not more than 0.00014 percent. (iii) Heavy metals (except Pb and As) (by...

21 CFR 82.5 - General specifications for straight colors.

Code of Federal Regulations, 2011 CFR

2011-04-01

... (in dilute HCl) (as BaCl2), not more than 0.05 percent. ... specifications: (1) In the case of a straight color listed in subpart B: (i) Lead (as Pb), not more than 0.001 percent. (ii) Arsenic (as As2O3), not more than 0.00014 percent. (iii) Heavy metals (except Pb and As) (by...

Employing Tip-Edge brackets on canines to simplify straight-wire mechanics.

PubMed

Rocke, R T

1994-10-01

The straight-wire appliance was developed in part to reduce wire bending and therefore make treatment results more predictable. Because tip prescription is built into the bracket slots, teeth are held at their final crown angulations throughout treatment. Straight-wire brackets are used in an attempt to produce bodily tooth movement. However, teeth tend to tip when a force is applied. This tipping, especially when canines are retracted, can deflect the arch wire causing supereruption of the incisors with a resultant increase in anterior overbite and an open bite in the canine/premolar area. Placing Tip-Edge brackets (TP Orthodontics, Inc., LaPorte, Ind.) on canines and employing tipping and uprighting mechanics on these teeth can overcome these problems. Two cases are presented to illustrate this approach to treatment.

Curvature-Based Environment Description for Robot Navigation Using Laser Range Sensors

PubMed Central

Vázquez-Martín, Ricardo; Núñez, Pedro; Bandera, Antonio; Sandoval, Francisco

2009-01-01

This work proposes a new feature detection and description approach for mobile robot navigation using 2D laser range sensors. The whole process consists of two main modules: a sensor data segmentation module and a feature detection and characterization module. The segmentation module is divided in two consecutive stages: First, the segmentation stage divides the laser scan into clusters of consecutive range readings using a distance-based criterion. Then, the second stage estimates the curvature function associated to each cluster and uses it to split it into a set of straight-line and curve segments. The curvature is calculated using a triangle-area representation where, contrary to previous approaches, the triangle side lengths at each range reading are adapted to the local variations of the laser scan, removing noise without missing relevant points. This representation remains unchanged in translation or rotation, and it is also robust against noise. Thus, it is able to provide the same segmentation results although the scene will be perceived from different viewpoints. Therefore, segmentation results are used to characterize the environment using line and curve segments, real and virtual corners and edges. Real scan data collected from different environments by using different platforms are used in the experiments in order to evaluate the proposed environment description algorithm. PMID:22461732

77 FR 32394 - Drawbridge Operation Regulation; The Straights, Harkers Island, NC

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-01

... across The Straights, in Harkers Island, NC. The bridge has a vertical clearance in the closed position... routes available for vessels with mast heights greater than 14 feet. In the event of an emergency, the...

Optimal compliant-surface jumping: a multi-segment model of springboard standing jumps.

PubMed

Cheng, Kuangyou B; Hubbard, Mont

2005-09-01

A multi-segment model is used to investigate optimal compliant-surface jumping strategies and is applied to springboard standing jumps. The human model has four segments representing the feet, shanks, thighs, and trunk-head-arms. A rigid bar with a rotational spring on one end and a point mass on the other end (the tip) models the springboard. Board tip mass, length, and stiffness are functions of the fulcrum setting. Body segments and board tip are connected by frictionless hinge joints and are driven by joint torque actuators at the ankle, knee, and hip. One constant (maximum isometric torque) and three variable functions (of instantaneous joint angle, angular velocity, and activation level) determine each joint torque. Movement from a nearly straight motionless initial posture to jump takeoff is simulated. The objective is to find joint torque activation patterns during board contact so that jump height can be maximized. Minimum and maximum joint angles, rates of change of normalized activation levels, and contact duration are constrained. Optimal springboard jumping simulations can reasonably predict jumper vertical velocity and jump height. Qualitatively similar joint torque activation patterns are found over different fulcrum settings. Different from rigid-surface jumping where maximal activation is maintained until takeoff, joint activation decreases near takeoff in compliant-surface jumping. The fulcrum-height relations in experimental data were predicted by the models. However, lack of practice at non-preferred fulcrum settings might have caused less jump height than the models' prediction. Larger fulcrum numbers are beneficial for taller/heavier jumpers because they need more time to extend joints.

Design Models for Shaping of a Tooth Profile of External Fine-Module Ratchet Teeth

NASA Astrophysics Data System (ADS)

Sharkov, O. V.; Koryagin, S. I.; Velikanov, N. L.

2016-04-01

Simulation of the shaping for the fine-module external ratchet teeth at which the contacting surfaces are formed by the straight segments is considered in this paper. The design schemes for shaping of the proposed ratchet teeth by a shaper cutter and a rack are obtained. It is defined that the maximum length of the straight segment of the front edge ratchet teeth will be formed at shaping by a rack cutter. The effect of a module, a gradient angle and a radius of blank circles on the length of the straight segment of the front edge ratchet teeth is investigated.

Extrapolation of Functions of Many Variables by Means of Metric Analysis

NASA Astrophysics Data System (ADS)

Kryanev, Alexandr; Ivanov, Victor; Romanova, Anastasiya; Sevastianov, Leonid; Udumyan, David

2018-02-01

The paper considers a problem of extrapolating functions of several variables. It is assumed that the values of the function of m variables at a finite number of points in some domain D of the m-dimensional space are given. It is required to restore the value of the function at points outside the domain D. The paper proposes a fundamentally new method for functions of several variables extrapolation. In the presented paper, the method of extrapolating a function of many variables developed by us uses the interpolation scheme of metric analysis. To solve the extrapolation problem, a scheme based on metric analysis methods is proposed. This scheme consists of two stages. In the first stage, using the metric analysis, the function is interpolated to the points of the domain D belonging to the segment of the straight line connecting the center of the domain D with the point M, in which it is necessary to restore the value of the function. In the second stage, based on the auto regression model and metric analysis, the function values are predicted along the above straight-line segment beyond the domain D up to the point M. The presented numerical example demonstrates the efficiency of the method under consideration.

Robust and accurate vectorization of line drawings.

PubMed

Hilaire, Xavier; Tombre, Karl

2006-06-01

This paper presents a method for vectorizing the graphical parts of paper-based line drawings. The method consists of separating the input binary image into layers of homogeneous thickness, skeletonizing each layer, segmenting the skeleton by a method based on random sampling, and simplifying the result. The segmentation method is robust with a best bound of 50 percent noise reached for indefinitely long primitives. Accurate estimation of the recognized vector's parameters is enabled by explicitly computing their feasibility domains. Theoretical performance analysis and expression of the complexity of the segmentation method are derived. Experimental results and comparisons with other vectorization systems are also provided.

Martini straight: Boosting performance using a shorter cutoff and GPUs

NASA Astrophysics Data System (ADS)

de Jong, Djurre H.; Baoukina, Svetlana; Ingólfsson, Helgi I.; Marrink, Siewert J.

2016-02-01

In molecular dynamics simulations, sufficient sampling is of key importance and a continuous challenge in the field. The coarse grain Martini force field has been widely used to enhance sampling. In its original implementation, this force field applied a shifted Lennard-Jones potential for the non-bonded van der Waals interactions, to avoid problems related to a relatively short cutoff. Here we investigate the use of a straight cutoff Lennard-Jones potential with potential modifiers. Together with a Verlet neighbor search algorithm, the modified potential allows the use of GPUs to accelerate the computations in Gromacs. We find that this alternative potential has little influence on most of the properties studied, including partitioning free energies, bulk liquid properties and bilayer properties. At the same time, energy conservation is kept within reasonable bounds. We conclude that the newly proposed straight cutoff approach is a viable alternative to the standard shifted potentials used in Martini, offering significant speedup even in the absence of GPUs.

Automatic segmentation of closed-contour features in ophthalmic images using graph theory and dynamic programming.

PubMed

Chiu, Stephanie J; Toth, Cynthia A; Bowes Rickman, Catherine; Izatt, Joseph A; Farsiu, Sina

2012-05-01

This paper presents a generalized framework for segmenting closed-contour anatomical and pathological features using graph theory and dynamic programming (GTDP). More specifically, the GTDP method previously developed for quantifying retinal and corneal layer thicknesses is extended to segment objects such as cells and cysts. The presented technique relies on a transform that maps closed-contour features in the Cartesian domain into lines in the quasi-polar domain. The features of interest are then segmented as layers via GTDP. Application of this method to segment closed-contour features in several ophthalmic image types is shown. Quantitative validation experiments for retinal pigmented epithelium cell segmentation in confocal fluorescence microscopy images attests to the accuracy of the presented technique.

Automatic segmentation of closed-contour features in ophthalmic images using graph theory and dynamic programming

PubMed Central

Chiu, Stephanie J.; Toth, Cynthia A.; Bowes Rickman, Catherine; Izatt, Joseph A.; Farsiu, Sina

2012-01-01

This paper presents a generalized framework for segmenting closed-contour anatomical and pathological features using graph theory and dynamic programming (GTDP). More specifically, the GTDP method previously developed for quantifying retinal and corneal layer thicknesses is extended to segment objects such as cells and cysts. The presented technique relies on a transform that maps closed-contour features in the Cartesian domain into lines in the quasi-polar domain. The features of interest are then segmented as layers via GTDP. Application of this method to segment closed-contour features in several ophthalmic image types is shown. Quantitative validation experiments for retinal pigmented epithelium cell segmentation in confocal fluorescence microscopy images attests to the accuracy of the presented technique. PMID:22567602

Focusators for laser-branding

NASA Astrophysics Data System (ADS)

Doskolovich, L. L.; Kazanskiy, N. L.; Kharitonov, S. I.; Uspleniev, G. V.

A new method is investigated for synthesis of computer-generated optical elements: focusators that are able to focus the radial-symmetrical laser beam into complex focal contours, in particular into alphanumeric symbols. The method is based on decomposition of the focal contour into segments of straight lines and semi-circles, following corresponding spacing out of the focusator on elementary segments (concentric rings or sectors) and solution of the inverse task of focusing from focusator segments into corresponding elements of the focal contour. The results of numerical computing of the field from synthesized focusators into the letters are presented. The theoretical efficiency of the focusators discussed is no less than 85%. The amplitude masks and the results of operational studies of synthesized focusators are presented.

Nonlinear resonances in linear segmented Paul trap of short central segment.

PubMed

Kłosowski, Łukasz; Piwiński, Mariusz; Pleskacz, Katarzyna; Wójtewicz, Szymon; Lisak, Daniel

2018-03-23

Linear segmented Paul trap system has been prepared for ion mass spectroscopy experiments. A non-standard approach to stability of trapped ions is applied to explain some effects observed with ensembles of calcium ions. Trap's stability diagram is extended to 3-dimensional one using additional ∆a besides standard q and a stability parameters. Nonlinear resonances in (q,∆a) diagrams are observed and described with a proposed model. The resonance lines have been identified using simple simulations and comparing the numerical and experimental results. The phenomenon can be applied in electron-impact ionization experiments for mass-identification of obtained ions or purification of their ensembles. This article is protected by copyright. All rights reserved.

Shear thinning effects on blood flow in straight and curved tubes

NASA Astrophysics Data System (ADS)

Cherry, Erica M.; Eaton, John K.

2013-07-01

Simulations were performed to determine the magnitude and types of errors one can expect when approximating blood in large arteries as a Newtonian fluid, particularly in the presence of secondary flows. This was accomplished by running steady simulations of blood flow in straight and curved tubes using both Newtonian and shear-thinning viscosity models. In the shear-thinning simulations, the viscosity was modeled as a shear rate-dependent function fit to experimental data. Simulations in straight tubes were modeled after physiologically relevant arterial flows, and flow parameters for the curved tube simulations were chosen to examine a variety of secondary flow strengths. The diameters ranged from 1 mm to 10 mm and the Reynolds numbers from 24 to 1500. Pressure and velocity data are reported for all simulations. In the straight tube simulations, the shear-thinning flows had flattened velocity profiles and higher pressure gradients compared to the Newtonian simulations. In the curved tube flows, the shear-thinning simulations tended to have blunted axial velocity profiles, decreased secondary flow strengths, and decreased axial vorticity compared to the Newtonian simulations. The cross-sectionally averaged pressure drops in the curved tubes were higher in the shear-thinning flows at low Reynolds number but lower at high Reynolds number. The maximum deviation in secondary flow magnitude averaged over the cross sectional area was 19% of the maximum secondary flow and the maximum deviation in axial vorticity was 25% of the maximum vorticity.

An improved multimodal method for sound propagation in nonuniform lined ducts.

PubMed

Bi, WenPing; Pagneux, Vincent; Lafarge, Denis; Aurégan, Yves

2007-07-01

An efficient method is proposed for modeling time harmonic acoustic propagation in a nonuniform lined duct without flow. The lining impedance is axially segmented uniform, but varies circumferentially. The sound pressure is expanded in term of rigid duct modes and an additional function that carries the information about the impedance boundary. The rigid duct modes and the additional function are known a priori so that calculations of the true liner modes, which are difficult, are avoided. By matching the pressure and axial velocity at the interface between different uniform segments, scattering matrices are obtained for each individual segment; these are then combined to construct a global scattering matrix for multiple segments. The present method is an improvement of the multimodal propagation method, developed in a previous paper [Bi et al., J. Sound Vib. 289, 1091-1111 (2006)]. The radial rate of convergence is improved from O(n(-2)), where n is the radial mode indices, to O(n(-4)). It is numerically shown that using the present method, acoustic propagation in the nonuniform lined intake of an aeroengine can be calculated by a personal computer for dimensionless frequency K up to 80, approaching the third blade passing frequency of turbofan noise.

Gibbs-Thomson Law for Singular Step Segments: Thermodynamics Versus Kinetics

NASA Technical Reports Server (NTRS)

Chernov, A. A.

2003-01-01

Classical Burton-Cabrera-Frank theory presumes that thermal fluctuations are so fast that at any time density of kinks on a step is comparable with the reciprocal intermolecular distance, so that the step rate is about isotropic within the crystal plane. Such azimuthal isotropy is, however, often not the case: Kink density may be much lower. In particular, it was recently found on the (010) face of orthorhombic lysozyme that interkink distance may exceed 500-600 intermolecular distances. Under such conditions, Gibbs-Thomson law (GTL) may not be applicable: On a straight step segment between two corners, communication between the comers occurs exclusively by kink exchange. Annihilation between kinks of opposite sign generated at the comers results in the grain in step energy entering GTL. If the step segment length l much greater than D/v, where D and v are the kink diffusivity and propagation rate, respectively, the opposite kinks have practically no chance to annihilate and GTL is not applicable. The opposite condition of the GTL applicability, l much less than D/v, is equivalent to the requirement that relative supersaturation Delta(sub mu)/kT much less than alpha/l, where alpha is molecular size. Thus, GTL may be applied to a segment of 10(exp 3)alpha approx. 3 x 10(exp -5)cm approx 0.3 micron only if supersaturation is less than 0.1%, while practically used driving forces for crystallization are much larger. Relationships alternative to the GTL for different, but low, kink density have been discussed. They confirm experimental evidences that the Burton-Cabrera-Frank theory of spiral growth is growth rates twice as low as compared to the observed figures. Also, application of GTL results in unrealistic step energy while suggested kinetic law give reasonable figures.

Demographic Trends and Advocacy Experiences of Gay-Straight Alliance Advisors

ERIC Educational Resources Information Center

Graybill, Emily C.; Varjas, Kris; Meyers, Joel; Dever, Bridget V.; Greenberg, Daphne; Roach, Andrew T.; Morillas, Catalina

2015-01-01

Using an ecological model, the individual-, school-, and sociocultural-level characteristics that affect gay-straight alliance (GSA) advisors were examined in the current study. The formation of GSAs has been one way that schools have sought to improve the school climate for lesbian, gay, bisexual, and transgender (LGBT) youth. Limited information…

MRI Brain Tumor Segmentation and Necrosis Detection Using Adaptive Sobolev Snakes.

PubMed

Nakhmani, Arie; Kikinis, Ron; Tannenbaum, Allen

2014-03-21

Brain tumor segmentation in brain MRI volumes is used in neurosurgical planning and illness staging. It is important to explore the tumor shape and necrosis regions at different points of time to evaluate the disease progression. We propose an algorithm for semi-automatic tumor segmentation and necrosis detection. Our algorithm consists of three parts: conversion of MRI volume to a probability space based on the on-line learned model, tumor probability density estimation, and adaptive segmentation in the probability space. We use manually selected acceptance and rejection classes on a single MRI slice to learn the background and foreground statistical models. Then, we propagate this model to all MRI slices to compute the most probable regions of the tumor. Anisotropic 3D diffusion is used to estimate the probability density. Finally, the estimated density is segmented by the Sobolev active contour (snake) algorithm to select smoothed regions of the maximum tumor probability. The segmentation approach is robust to noise and not very sensitive to the manual initialization in the volumes tested. Also, it is appropriate for low contrast imagery. The irregular necrosis regions are detected by using the outliers of the probability distribution inside the segmented region. The necrosis regions of small width are removed due to a high probability of noisy measurements. The MRI volume segmentation results obtained by our algorithm are very similar to expert manual segmentation.

MRI brain tumor segmentation and necrosis detection using adaptive Sobolev snakes

NASA Astrophysics Data System (ADS)

Nakhmani, Arie; Kikinis, Ron; Tannenbaum, Allen

2014-03-01

Brain tumor segmentation in brain MRI volumes is used in neurosurgical planning and illness staging. It is important to explore the tumor shape and necrosis regions at di erent points of time to evaluate the disease progression. We propose an algorithm for semi-automatic tumor segmentation and necrosis detection. Our algorithm consists of three parts: conversion of MRI volume to a probability space based on the on-line learned model, tumor probability density estimation, and adaptive segmentation in the probability space. We use manually selected acceptance and rejection classes on a single MRI slice to learn the background and foreground statistical models. Then, we propagate this model to all MRI slices to compute the most probable regions of the tumor. Anisotropic 3D di usion is used to estimate the probability density. Finally, the estimated density is segmented by the Sobolev active contour (snake) algorithm to select smoothed regions of the maximum tumor probability. The segmentation approach is robust to noise and not very sensitive to the manual initialization in the volumes tested. Also, it is appropriate for low contrast imagery. The irregular necrosis regions are detected by using the outliers of the probability distribution inside the segmented region. The necrosis regions of small width are removed due to a high probability of noisy measurements. The MRI volume segmentation results obtained by our algorithm are very similar to expert manual segmentation.

An in-situ measuring method for planar straightness error

NASA Astrophysics Data System (ADS)

Chen, Xi; Fu, Luhua; Yang, Tongyu; Sun, Changku; Wang, Zhong; Zhao, Yan; Liu, Changjie

2018-01-01

According to some current problems in the course of measuring the plane shape error of workpiece, an in-situ measuring method based on laser triangulation is presented in this paper. The method avoids the inefficiency of traditional methods like knife straightedge as well as the time and cost requirements of coordinate measuring machine(CMM). A laser-based measuring head is designed and installed on the spindle of a numerical control(NC) machine. The measuring head moves in the path planning to measure measuring points. The spatial coordinates of the measuring points are obtained by the combination of the laser triangulation displacement sensor and the coordinate system of the NC machine, which could make the indicators of measurement come true. The method to evaluate planar straightness error adopts particle swarm optimization(PSO). To verify the feasibility and accuracy of the measuring method, simulation experiments were implemented with a CMM. Comparing the measurement results of measuring head with the corresponding measured values obtained by composite measuring machine, it is verified that the method can realize high-precise and automatic measurement of the planar straightness error of the workpiece.

49 CFR 192.715 - Transmission lines: Permanent field repair of welds.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 3 2014-10-01 2014-10-01 false Transmission lines: Permanent field repair of... § 192.715 Transmission lines: Permanent field repair of welds. Each weld that is unacceptable under § 192.241(c) must be repaired as follows: (a) If it is feasible to take the segment of transmission line...

49 CFR 192.715 - Transmission lines: Permanent field repair of welds.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Transmission lines: Permanent field repair of... § 192.715 Transmission lines: Permanent field repair of welds. Each weld that is unacceptable under § 192.241(c) must be repaired as follows: (a) If it is feasible to take the segment of transmission line...

49 CFR 192.715 - Transmission lines: Permanent field repair of welds.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 3 2013-10-01 2013-10-01 false Transmission lines: Permanent field repair of... § 192.715 Transmission lines: Permanent field repair of welds. Each weld that is unacceptable under § 192.241(c) must be repaired as follows: (a) If it is feasible to take the segment of transmission line...

49 CFR 192.715 - Transmission lines: Permanent field repair of welds.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 3 2012-10-01 2012-10-01 false Transmission lines: Permanent field repair of... § 192.715 Transmission lines: Permanent field repair of welds. Each weld that is unacceptable under § 192.241(c) must be repaired as follows: (a) If it is feasible to take the segment of transmission line...

49 CFR 192.715 - Transmission lines: Permanent field repair of welds.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 3 2011-10-01 2011-10-01 false Transmission lines: Permanent field repair of... § 192.715 Transmission lines: Permanent field repair of welds. Each weld that is unacceptable under § 192.241(c) must be repaired as follows: (a) If it is feasible to take the segment of transmission line...

Electro-Optic Segment-Segment Sensors for Radio and Optical Telescopes

NASA Technical Reports Server (NTRS)

Abramovici, Alex

2012-01-01

A document discusses an electro-optic sensor that consists of a collimator, attached to one segment, and a quad diode, attached to an adjacent segment. Relative segment-segment motion causes the beam from the collimator to move across the quad diode, thus generating a measureable electric signal. This sensor type, which is relatively inexpensive, can be configured as an edge sensor, or as a remote segment-segment motion sensor.

Dynamic programming in parallel boundary detection with application to ultrasound intima-media segmentation.

PubMed

Zhou, Yuan; Cheng, Xinyao; Xu, Xiangyang; Song, Enmin

2013-12-01

Segmentation of carotid artery intima-media in longitudinal ultrasound images for measuring its thickness to predict cardiovascular diseases can be simplified as detecting two nearly parallel boundaries within a certain distance range, when plaque with irregular shapes is not considered. In this paper, we improve the implementation of two dynamic programming (DP) based approaches to parallel boundary detection, dual dynamic programming (DDP) and piecewise linear dual dynamic programming (PL-DDP). Then, a novel DP based approach, dual line detection (DLD), which translates the original 2-D curve position to a 4-D parameter space representing two line segments in a local image segment, is proposed to solve the problem while maintaining efficiency and rotation invariance. To apply the DLD to ultrasound intima-media segmentation, it is imbedded in a framework that employs an edge map obtained from multiplication of the responses of two edge detectors with different scales and a coupled snake model that simultaneously deforms the two contours for maintaining parallelism. The experimental results on synthetic images and carotid arteries of clinical ultrasound images indicate improved performance of the proposed DLD compared to DDP and PL-DDP, with respect to accuracy and efficiency. Copyright © 2013 Elsevier B.V. All rights reserved.

CellSegm - a MATLAB toolbox for high-throughput 3D cell segmentation

PubMed Central

2013-01-01

The application of fluorescence microscopy in cell biology often generates a huge amount of imaging data. Automated whole cell segmentation of such data enables the detection and analysis of individual cells, where a manual delineation is often time consuming, or practically not feasible. Furthermore, compared to manual analysis, automation normally has a higher degree of reproducibility. CellSegm, the software presented in this work, is a Matlab based command line software toolbox providing an automated whole cell segmentation of images showing surface stained cells, acquired by fluorescence microscopy. It has options for both fully automated and semi-automated cell segmentation. Major algorithmic steps are: (i) smoothing, (ii) Hessian-based ridge enhancement, (iii) marker-controlled watershed segmentation, and (iv) feature-based classfication of cell candidates. Using a wide selection of image recordings and code snippets, we demonstrate that CellSegm has the ability to detect various types of surface stained cells in 3D. After detection and outlining of individual cells, the cell candidates can be subject to software based analysis, specified and programmed by the end-user, or they can be analyzed by other software tools. A segmentation of tissue samples with appropriate characteristics is also shown to be resolvable in CellSegm. The command-line interface of CellSegm facilitates scripting of the separate tools, all implemented in Matlab, offering a high degree of flexibility and tailored workflows for the end-user. The modularity and scripting capabilities of CellSegm enable automated workflows and quantitative analysis of microscopic data, suited for high-throughput image based screening. PMID:23938087

CellSegm - a MATLAB toolbox for high-throughput 3D cell segmentation.

PubMed

Hodneland, Erlend; Kögel, Tanja; Frei, Dominik Michael; Gerdes, Hans-Hermann; Lundervold, Arvid

2013-08-09

: The application of fluorescence microscopy in cell biology often generates a huge amount of imaging data. Automated whole cell segmentation of such data enables the detection and analysis of individual cells, where a manual delineation is often time consuming, or practically not feasible. Furthermore, compared to manual analysis, automation normally has a higher degree of reproducibility. CellSegm, the software presented in this work, is a Matlab based command line software toolbox providing an automated whole cell segmentation of images showing surface stained cells, acquired by fluorescence microscopy. It has options for both fully automated and semi-automated cell segmentation. Major algorithmic steps are: (i) smoothing, (ii) Hessian-based ridge enhancement, (iii) marker-controlled watershed segmentation, and (iv) feature-based classfication of cell candidates. Using a wide selection of image recordings and code snippets, we demonstrate that CellSegm has the ability to detect various types of surface stained cells in 3D. After detection and outlining of individual cells, the cell candidates can be subject to software based analysis, specified and programmed by the end-user, or they can be analyzed by other software tools. A segmentation of tissue samples with appropriate characteristics is also shown to be resolvable in CellSegm. The command-line interface of CellSegm facilitates scripting of the separate tools, all implemented in Matlab, offering a high degree of flexibility and tailored workflows for the end-user. The modularity and scripting capabilities of CellSegm enable automated workflows and quantitative analysis of microscopic data, suited for high-throughput image based screening.

On the barn owl's visual pre-attack behavior: I. Structure of head movements and motion patterns.

PubMed

Ohayon, Shay; van der Willigen, Robert F; Wagner, Hermann; Katsman, Igor; Rivlin, Ehud

2006-09-01

Barn owls exhibit a rich repertoire of head movements before taking off for prey capture. These movements occur mainly at light levels that allow for the visual detection of prey. To investigate these movements and their functional relevance, we filmed the pre-attack behavior of barn owls. Off-line image analysis enabled reconstruction of all six degrees of freedom of head movements. Three categories of head movements were observed: fixations, head translations and head rotations. The observed rotations contained a translational component. Head rotations did not follow Listing's law, but could be well described by a second-order surface, which indicated that they are in close agreement with Donder's law. Head translations did not contain any significant rotational components. Translations were further segmented into straight-line and curved paths. Translations along an axis perpendicular to the line of sight were similar to peering movements observed in other animals. We suggest that these basic motion elements (fixations, head rotations, translations along a straight line, and translation along a curved trajectory) may be combined to form longer and more complex behavior. We speculate that these head movements mainly underlie estimation of distance during prey capture.

Segmental heterogeneity in Bcl-2, Bcl-xL and Bax expression in rat tubular epithelium after ischemia-reperfusion.

PubMed

Valdés, Francisco; Pásaro, Eduardo; Díaz, Inmaculada; Centeno, Alberto; López, Eduardo; García-Doval, Sandra; González-Roces, Severino; Alba, Alfonso; Laffon, Blanca

2008-06-01

Studies in rats with bilateral clamping of renal arteries showed transient Bcl-2, Bcl-xL and Bax expression in renal tubular epithelium following ischemia-reperfusion. However, current data on the preferential localization of specific mRNAs or proteins are limited because gene expression was not analysed at segmental level. This study analyses the mRNA expression of Bcl-2, Bcl-xL and Bax in four segments of proximal and distal tubules localized in the renal cortex and outer medulla in rat kidneys with bilateral renal clamping for 30 min and seven reperfusion times versus control animals without clamp. Proximal convoluted tubule (PCT), distal convoluted tubule (DCT), proximal straight tubule (PST) and medullary thick ascending limb (MTAL) were obtained by manual microdissection. RT-PCR was used to analyse mRNA expression at segmental level. Proximal convoluted tubule and MTAL showed early, persistent and balanced up-regulation of Bcl-2, Bcl-xL and Bax, while PST and DCT revealed only Bcl-2 and Bcl-xL, when only Bax was detected in PST. DCT expressed Bcl-xL initially, and persistent Bcl-2 later. These patterns suggest a heterogeneous apoptosis regulatory response in rat renal tubules after ischemia-reperfusion, independently of cortical or medullary location. This heterogeneity of the expression patterns of Bcl-2 genes could explain the different susceptibility to undergo apoptosis, the different threshold to ischemic damage and the different adaptive capacity to injury among these tubular segments.

Potential advantages of curve sawing non-straight hardwood logs

Treesearch

Philip A. Araman

2007-01-01

Curve sawing is not new to the softwood industry. Softwood sawmill managers think about how fast they can push logs through their sawmill to maximize the yield of 1x and 2x lumber. Curve sawing helps mills maximize yield when sawing non-straight logs. Hardwood sawmill managers don’t want to push logs through their sawmills, because they want to maximize lumber value...

Spray Cooling Trajectory Angle Impact Upon Heat Flux Using a Straight Finned Enhanced Surface

NASA Technical Reports Server (NTRS)

Silk, Eric A.; Kim, Jungho; Kiger, Ken

2005-01-01

Experiments were conducted to study the effects of spray trajectory angles upon heat flux for flat and enhanced surface spray cooling. The surface enhancement consisted of straight fins machined on the top surface of a copper heater block. Spray cooling curves were obtained with the straight fin surface aligned both parallel (axial) and perpendicular (transverse) to the spray axis. Measurements were also obtained on a flat surface heater block for comparison purposes. Each copper block had a cross-sectional area of 2.0 sq cm. A 2x2 nozzle array was used with PF-5060 as the working fluid. Thermal performance data was obtained under nominally degassed (chamber pressure of 41.4 kPa) conditions. Results show that the maximum CHF in all cases was attained for a trajectory angle of 30' from the surface normal. Furthermore, trajectory angles applied to straight finned surfaces can have a critical heat flux (CHF) enhancement as much as 75% (heat flux value of 140 W/sq cm) relative to the vertical spray orientation for the analogous flat surface case under nominally degassed conditions.

Modification of the short straight sections of the high energy booster of the SSC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, M.; Johnson, D.; Kocur, P.

1993-05-01

The tracking analysis with the High Energy Booster (HEB) of the Superconducting Super Collider (SSC) indicated that the machine dynamic aperture for the current lattice (Rev 0 lattice) was limited by the quadrupoles in the short straight sections. A new lattice, Rev 1, with modified short straight sections was proposed. The results of tracking the two lattices up to 5 [times] 10[sup 5] turns (20 seconds at the injection energy) with various random seeds are presented in this paper. The new lattice has increased dynamic aperture from [approximately]7 mm to [approximately]8 mm, increases the abort kicker effectiveness, and eliminates onemore » family (length) of main quadrupoles. The code DIMAD was used for matching the new short straight sections to the ring. The code TEAPOT was used for the short term tracking and to create a machine file, zfile, which could in turn be used to generate a one-turn map with the ZLIB for fast long-term tracking using a symplectic one-turn map tracking program ZIMAPTRK.« less

Modification of the short straight sections of the high energy booster of the SSC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, M.; Johnson, D.; Kocur, P.

1993-05-01

The tracking analysis with the High Energy Booster (HEB) of the Superconducting Super Collider (SSC) indicated that the machine dynamic aperture for the current lattice (Rev 0 lattice) was limited by the quadrupoles in the short straight sections. A new lattice, Rev 1, with modified short straight sections was proposed. The results of tracking the two lattices up to 5 {times} 10{sup 5} turns (20 seconds at the injection energy) with various random seeds are presented in this paper. The new lattice has increased dynamic aperture from {approximately}7 mm to {approximately}8 mm, increases the abort kicker effectiveness, and eliminates onemore » family (length) of main quadrupoles. The code DIMAD was used for matching the new short straight sections to the ring. The code TEAPOT was used for the short term tracking and to create a machine file, zfile, which could in turn be used to generate a one-turn map with the ZLIB for fast long-term tracking using a symplectic one-turn map tracking program ZIMAPTRK.« less

5. SOUTH SIDE DRIVE AT CHAPEL STRAIGHT. NOTE BIKE PATH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. SOUTH SIDE DRIVE AT CHAPEL STRAIGHT. NOTE BIKE PATH AND BOULDER LANE EDGING. CHAPEL SPIRE AT CENTER. LOCATION OF OLD YOSEMITE VILLAGE AT CENTER DISTANCE. NORTH DOME AT REAR. LOOKING NNE. GIS: N-37 44 21.8 / W-119 35 39.3 - Yosemite National Park Roads & Bridges, Yosemite Village, Mariposa County, CA

High accuracy OMEGA timekeeping

NASA Technical Reports Server (NTRS)

Imbier, E. A.

1982-01-01

The Smithsonian Astrophysical Observatory (SAO) operates a worldwide satellite tracking network which uses a combination of OMEGA as a frequency reference, dual timing channels, and portable clock comparisons to maintain accurate epoch time. Propagational charts from the U.S. Coast Guard OMEGA monitor program minimize diurnal and seasonal effects. Daily phase value publications of the U.S. Naval Observatory provide corrections to the field collected timing data to produce an averaged time line comprised of straight line segments called a time history file (station clock minus UTC). Depending upon clock location, reduced time data accuracies of between two and eight microseconds are typical.

Optical mass memory system (AMM-13). AMM-13 system segment specification

NASA Technical Reports Server (NTRS)

Bailey, G. A.

1980-01-01

The performance, design, development, and test requirements for an optical mass data storage and retrieval system prototype (AMM-13) are established. This system interfaces to other system segments of the NASA End-to-End Data System via the Data Base Management System segment and is designed to have a storage capacity of 10 to the 13th power bits (10 to the 12th power bits on line). The major functions of the system include control, input and output, recording of ingested data, fiche processing/replication and storage and retrieval.

Effects of inlet flow field conditions on the performance of centrifugal compressor diffusers: Part 2 -- Straight-channel diffuser

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deniz, S.; Greitzer, E.M.; Cumpsty, N.A.

2000-01-01

This is Part 2 of an examination of the influence of inlet flow conditions on the performance and operating range of centrifugal compressor vaned diffusers. The paper describes tests of a straight-channel type diffuser, sometimes called a wedge-vane diffuser, and compares the results with those from the discrete-passage diffusers described in Part 1. Effects of diffuser inlet Mach number, flow angle, blockage, and axial flow nonuniformity on diffuser pressure recovery and operating range are addressed. The straight-channel diffuser investigated has 30 vanes and was designed for the same aerodynamic duty as the discrete-passage diffuser described in Part 1. The rangesmore » of the overall pressure recovery coefficients were 0.50--0.78 for the straight-channel diffuser and 0.50--0.70 for the discrete-passage diffuser, except when the diffuser was choked. In other words, the maximum pressure recovery of the straight-channel diffuser was found to be roughly 10% higher than that of the discrete-passage diffuser investigated. The two types of diffuser showed similar behavior regarding the dependence of pressure recovery on diffuser inlet flow angle and the insensitivity of the performance to inlet flow field axial distortion and Mach number. The operating range of the straight-channel diffuser, as for the discrete-passage diffusers, was limited by the onset of rotating stall at a fixed momentum-averaged flow angle into the diffuser, which was for the straight-channel diffuser, {alpha}{sub crit} = 70 {+-} 0.5 deg. The background, nomenclature, and description of the facility and method are all given in Part 1.« less

A multi-scale tensor voting approach for small retinal vessel segmentation in high resolution fundus images.

PubMed

Christodoulidis, Argyrios; Hurtut, Thomas; Tahar, Houssem Ben; Cheriet, Farida

2016-09-01

Segmenting the retinal vessels from fundus images is a prerequisite for many CAD systems for the automatic detection of diabetic retinopathy lesions. So far, research efforts have concentrated mainly on the accurate localization of the large to medium diameter vessels. However, failure to detect the smallest vessels at the segmentation step can lead to false positive lesion detection counts in a subsequent lesion analysis stage. In this study, a new hybrid method for the segmentation of the smallest vessels is proposed. Line detection and perceptual organization techniques are combined in a multi-scale scheme. Small vessels are reconstructed from the perceptual-based approach via tracking and pixel painting. The segmentation was validated in a high resolution fundus image database including healthy and diabetic subjects using pixel-based as well as perceptual-based measures. The proposed method achieves 85.06% sensitivity rate, while the original multi-scale line detection method achieves 81.06% sensitivity rate for the corresponding images (p<0.05). The improvement in the sensitivity rate for the database is 6.47% when only the smallest vessels are considered (p<0.05). For the perceptual-based measure, the proposed method improves the detection of the vasculature by 7.8% against the original multi-scale line detection method (p<0.05). Copyright © 2016 Elsevier Ltd. All rights reserved.

Equilibrium charge distribution on a finite straight one-dimensional wire

NASA Astrophysics Data System (ADS)

Batle, Josep; Ciftja, Orion; Abdalla, Soliman; Elhoseny, Mohamed; Alkhambashi, Majid; Farouk, Ahmed

2017-09-01

The electrostatic properties of uniformly charged regular bodies are prominently discussed on college-level electromagnetism courses. However, one of the most basic problems of electrostatics that deals with how a continuous charge distribution reaches equilibrium is rarely mentioned at this level. In this work we revisit the problem of equilibrium charge distribution on a straight one-dimensional (1D) wire with finite length. The majority of existing treatments in the literature deal with the 1D wire as a limiting case of a higher-dimensional structure that can be treated analytically for a Coulomb interaction potential between point charges. Surprisingly, different models (for instance, an ellipsoid or a cylinder model) may lead to different results, thus there is even some ambiguity on whether the problem is well-posed. In this work we adopt a different approach where we do not start with any higher-dimensional body that reduces to a 1D wire in the appropriate limit. Instead, our starting point is the obvious one, a finite straight 1D wire that contains charge. However, the new tweak in the model is the assumption that point charges interact with each other via a non-Coulomb power-law interaction potential. This potential is well-behaved, allows exact analytical results and approaches the standard Coulomb interaction potential as a limit. The results originating from this approach suggest that the equilibrium charge distribution for a finite straight 1D wire is a uniform charge density when the power-law interaction potential approaches the Coulomb interaction potential as a suitable limit. We contrast such a finding to results obtained using a different regularised logarithmic interaction potential which allows exact treatment in 1D. The present self-contained material may be of interest to instructors teaching electromagnetism as well as students who will discover that simple-looking problems may sometimes pose important scientific challenges.

Identification of the Genome Segments of Bluetongue Virus Serotype 26 (Isolate KUW2010/02) that Restrict Replication in a Culicoides sonorensis Cell Line (KC Cells).

PubMed

Pullinger, Gillian D; Guimerà Busquets, Marc; Nomikou, Kyriaki; Boyce, Mark; Attoui, Houssam; Mertens, Peter P

2016-01-01

Bluetongue virus (BTV) can infect most ruminant species and is usually transmitted by adult, vector-competent biting midges (Culicoides spp.). Infection with BTV can cause severe clinical signs and can be fatal, particularly in naïve sheep and some deer species. Although 24 distinct BTV serotypes were recognized for several decades, additional 'types' have recently been identified, including BTV-25 (from Switzerland), BTV-26 (from Kuwait) and BTV-27 from France (Corsica). Although BTV-25 has failed to grow in either insect or mammalian cell cultures, BTV-26 (isolate KUW2010/02), which can be transmitted horizontally between goats in the absence of vector insects, does not replicate in a Culicoides sonorensis cell line (KC cells) but can be propagated in mammalian cells (BSR cells). The BTV genome consists of ten segments of linear dsRNA. Mono-reassortant viruses were generated by reverse-genetics, each one containing a single BTV-26 genome segment in a BTV-1 genetic-background. However, attempts to recover a mono-reassortant containing genome-segment 2 (Seg-2) of BTV-26 (encoding VP2), were unsuccessful but a triple-reassortant was successfully generated containing Seg-2, Seg-6 and Seg-7 (encoding VP5 and VP7 respectively) of BTV-26. Reassortants were recovered and most replicated well in mammalian cells (BSR cells). However, mono-reassortants containing Seg-1 or Seg-3 of BTV-26 (encoding VP1, or VP3 respectively) and the triple reassortant failed to replicate, while a mono-reassortant containing Seg-7 of BTV-26 only replicated slowly in KC cells.

Novel Straight and Circular Road Driving Control of Electric Power Assisted Wheelchair Based on Fuzzy Algorithm

NASA Astrophysics Data System (ADS)

Seki, Hirokazu; Tadakuma, Susumu

This paper describes a novel straight and circular road driving control scheme for electric power assisted wheelchairs. “Electric power assisted wheelchair” which assists the driving force by electric motors is expected to be widely used as a mobility support system for elderly people and disabled people, however, the performance of the straight and circular road driving must be further improved because the two wheels drive independently. This paper proposes a novel driving control scheme based on fuzzy algorithm to realize the stable and reliable driving on straight and circular roads. The suitable assisted torque of the right and left wheels is determined by fuzzy algorithm based on the posture angular velocity of the wheelchair and the human input torque proportion of the right and left wheels. Some experiments on the practical roads show the effectiveness of the proposed control system.

Text, photo, and line extraction in scanned documents

NASA Astrophysics Data System (ADS)

Erkilinc, M. Sezer; Jaber, Mustafa; Saber, Eli; Bauer, Peter; Depalov, Dejan

2012-07-01

We propose a page layout analysis algorithm to classify a scanned document into different regions such as text, photo, or strong lines. The proposed scheme consists of five modules. The first module performs several image preprocessing techniques such as image scaling, filtering, color space conversion, and gamma correction to enhance the scanned image quality and reduce the computation time in later stages. Text detection is applied in the second module wherein wavelet transform and run-length encoding are employed to generate and validate text regions, respectively. The third module uses a Markov random field based block-wise segmentation that employs a basis vector projection technique with maximum a posteriori probability optimization to detect photo regions. In the fourth module, methods for edge detection, edge linking, line-segment fitting, and Hough transform are utilized to detect strong edges and lines. In the last module, the resultant text, photo, and edge maps are combined to generate a page layout map using K-Means clustering. The proposed algorithm has been tested on several hundred documents that contain simple and complex page layout structures and contents such as articles, magazines, business cards, dictionaries, and newsletters, and compared against state-of-the-art page-segmentation techniques with benchmark performance. The results indicate that our methodology achieves an average of ˜89% classification accuracy in text, photo, and background regions.

Comparative transcriptome analysis of cotton fiber development of Upland cotton (Gossypium hirsutum) and Chromosome Segment Substitution Lines from G. hirsutum × G. barbadense.

PubMed

Li, Peng-Tao; Wang, Mi; Lu, Quan-Wei; Ge, Qun; Rashid, Md Harun Or; Liu, Ai-Ying; Gong, Ju-Wu; Shang, Hai-Hong; Gong, Wan-Kui; Li, Jun-Wen; Song, Wei-Wu; Guo, Li-Xue; Su, Wei; Li, Shao-Qi; Guo, Xiao-Ping; Shi, Yu-Zhen; Yuan, You-Lu

2017-09-08

How to develop new cotton varieties possessing high yield traits of Upland cotton and superior fiber quality traits of Sea Island cotton remains a key task for cotton breeders and researchers. While multiple attempts bring in little significant progresses, the development of Chromosome Segment Substitution Lines (CSSLs) from Gossypium barbadense in G. hirsutum background provided ideal materials for aforementioned breeding purposes in upland cotton improvement. Based on the excellent fiber performance and relatively clear chromosome substitution segments information identified by Simple Sequence Repeat (SSR) markers, two CSSLs, MBI9915 and MBI9749, together with the recurrent parent CCRI36 were chosen to conduct transcriptome sequencing during the development stages of fiber elongation and Secondary Cell Wall (SCW) synthesis (from 10DPA and 28DPA), aiming at revealing the mechanism of fiber development and the potential contribution of chromosome substitution segments from Sea Island cotton to fiber development of Upland cotton. In total, 15 RNA-seq libraries were constructed and sequenced separately, generating 705.433 million clean reads with mean GC content of 45.13% and average Q30 of 90.26%. Through multiple comparisons between libraries, 1801 differentially expressed genes (DEGs) were identified, of which the 902 up-regulated DEGs were mainly involved in cell wall organization and response to oxidative stress and auxin, while the 898 down-regulated ones participated in translation, regulation of transcription, DNA-templated and cytoplasmic translation based on GO annotation and KEGG enrichment analysis. Subsequently, STEM software was performed to explicate the temporal expression pattern of DEGs. Two peroxidases and four flavonoid pathway-related genes were identified in the "oxidation-reduction process", which could play a role in fiber development and quality formation. Finally, the reliability of RNA-seq data was validated by quantitative real-time PCR

Straight and chopped DC performance data for a reliance EV-250AT motor with a General Electric EV-1 controller

NASA Technical Reports Server (NTRS)

Edie, P. C.

1981-01-01

Straight and chopped DC motor performances for a Reliance EV-250AT motor with an EV-1 controller were examined. Effects of motor temperature and operating voltage are shown. It is found that the maximum motor efficiency is approximately 85% at low operating temperatures in the straight DC mode. Chopper efficiency is 95% under all operating conditions. For equal speeds, the motor operated in the chopped mode develops slightly more torque and draws more current than it does in the straight DC mode.

Dimensionality and regional strike analyses of the Cibeber segment, Cimandiri fault zone, West Jawa, Indonesia

NASA Astrophysics Data System (ADS)

Febriani, F.; Handayani, L.; Setyani, A.; Anggono, T.; Syuhada; Soedjatmiko, B.

2018-03-01

The dimensionality and regional strike analyses of the Cimandiri Fault, West Java, Indonesia have been investigated. The Cimandiri Fault consists of six segments. They are Loji, Cidadap, Nyalindung, Cibeber, Saguling and Padalarang segments. The magnetotelluric (MT) investigation was done in the Cibeber segment. There were 42 observation points of the magnetotelluric data, which were distributed along 2 lines. The magnetotelluric phase tensor has been applied to determine the dimensionality and regional strike of the Cibeber segment, Cimandiri Fault, West Java. The result of the dimensionality analysis shows that the range values of the skew angle value which indicate the dimensionality of the study area are -5 ≤ β ≥ 5. These values indicate if we would like to generate the subsurface model of the Cibeber segment by using the magnetotelluric data, it is safe to assume that the Cibeber segment has the 2-D. While the regional strike analysis presents that the regional strike of the Cibeber segment is about N70-80°E.

Scene Segmentation For Autonomous Robotic Navigation Using Sequential Laser Projected Structured Light

NASA Astrophysics Data System (ADS)

Brown, C. David; Ih, Charles S.; Arce, Gonzalo R.; Fertell, David A.

1987-01-01

Vision systems for mobile robots or autonomous vehicles navigating in an unknown terrain environment must provide a rapid and accurate method of segmenting the scene ahead into regions of pathway and background. A major distinguishing feature between the pathway and background is the three dimensional texture of these two regions. Typical methods of textural image segmentation are very computationally intensive, often lack the required robustness, and are incapable of sensing the three dimensional texture of various regions of the scene. A method is presented where scanned laser projected lines of structured light, viewed by a stereoscopically located single video camera, resulted in an image in which the three dimensional characteristics of the scene were represented by the discontinuity of the projected lines. This image was conducive to processing with simple regional operators to classify regions as pathway or background. Design of some operators and application methods, and demonstration on sample images are presented. This method provides rapid and robust scene segmentation capability that has been implemented on a microcomputer in near real time, and should result in higher speed and more reliable robotic or autonomous navigation in unstructured environments.

Transition duct system with metal liners for delivering hot-temperature gases in a combustion turbine engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wiebe, David J.

A transition duct system (10) for delivering hot-temperature gases from a plurality of combustors in a combustion turbine engine is provided. The system includes an exit piece (16) for each combustor. The exit piece may include a straight path segment (26) and an arcuate connecting segment (36). A respective straight metal liner (92) and an arcuate metal liner (94) may be each inwardly disposed onto a metal outer shell (38) along the straight path segment and the arcuate connecting segment (36) of the exit piece. Structural arrangements are provided to securely attach the respective liners in the presence of substantialmore » flow path pressurization. Cost-effective serviceability of the transition duct systems is realizable since the liners can be readily removed and replaced as needed.« less

Engineering of multi-segmented light tunnel and flattop focus with designed axial lengths and gaps

NASA Astrophysics Data System (ADS)

Yu, Yanzhong; Huang, Han; Zhou, Mianmian; Zhan, Qiwen

2018-01-01

Based on the radiation pattern from a sectional-uniform line source antenna, a three-dimensional (3D) focus engineering technique for the creation of multi-segmented light tunnel and flattop focus with designed axial lengths and gaps is proposed. Under a 4Pi focusing system, the fields radiated from sectional-uniform magnetic and electromagnetic current line source antennas are employed to generate multi-segmented optical tube and flattop focus, respectively. Numerical results demonstrate that the produced light tube and flattop focus remain homogeneous along the optical axis; and their lengths of the nth segment and the nth gap between consecutive segments can be easily adjusted and only depend on the sizes of the nth section and the nth blanking between adjacent sectional antennas. The optical tube is a pure azimuthally polarized field but for the flattop focus the longitudinal polarization is dominant on the optical axis. To obtain the required pupil plane illumination for constructing the above focal field with prescribed characteristics, the inverse problem of the antenna radiation field is solved. These peculiar focusing fields might find potential applications in multi-particle acceleration, multi-particle trapping and manipulation.

Hot spot detection, segmentation, and identification in PET images

NASA Astrophysics Data System (ADS)

Blaffert, Thomas; Meetz, Kirsten

2006-03-01

Positron Emission Tomography (PET) images provide functional or metabolic information from areas of high concentration of [18F]fluorodeoxyglucose (FDG) tracer, the "hot spots". These hot spots can be easily detected by the eye, but delineation and size determination required e.g. for diagnosis and staging of cancer is a tedious task that demands for automation. The approach for such an automated hot spot segmentation described in this paper comprises three steps: A region of interest detection by the watershed transform, a heart identification by an evaluation of scan lines, and the final segmentation of hot spot areas by a local threshold. The region of interest detection is the essential step, since it localizes the hot spot identification and the final segmentation. The heart identification is an example of how to differentiate between hot spots. Finally, we demonstrate the combination of PET and CT data. Our method is applicable to other techniques like SPECT.

Automatic airline baggage counting using 3D image segmentation

NASA Astrophysics Data System (ADS)

Yin, Deyu; Gao, Qingji; Luo, Qijun

2017-06-01

The baggage number needs to be checked automatically during baggage self-check-in. A fast airline baggage counting method is proposed in this paper using image segmentation based on height map which is projected by scanned baggage 3D point cloud. There is height drop in actual edge of baggage so that it can be detected by the edge detection operator. And then closed edge chains are formed from edge lines that is linked by morphological processing. Finally, the number of connected regions segmented by closed chains is taken as the baggage number. Multi-bag experiment that is performed on the condition of different placement modes proves the validity of the method.

Straight spinning cosmic strings in Brans-Dicke gravity

NASA Astrophysics Data System (ADS)

Dos Santos, S. Mittmann; da Silva, J. M. Hoff; Cindra, J. L.

2018-03-01

An exact solution of straight spinning cosmic strings in Brans-Dicke theory of gravitation is presented. The possibility of the existence of closed time-like curves around these cosmic strings is analyzed. Furthermore, the stability about the formation of the topological defect discussed here is checked. It is shown that the existence of a suitable choice for the integration constants in which closed time-like curves are not allowed. We also study the (im)possibility of using the obtained spacetime in the rotational curves problem.

Bacterial chondronecrosis with osteomyelitis in broilers: influence of sires and straight-run versus sex-separate rearing.

PubMed

Wideman, R F; Al-Rubaye, A; Reynolds, D; Yoho, D; Lester, H; Spencer, C; Hughes, J D; Pevzner, I Y

2014-07-01

Two experiments (E1, E2) were conducted to compare the influence of sires (sire A on dam C vs. sire B on dam C) and straight-run versus sex-separate rearing on the incidence of bacterial chondronecrosis with osteomyelitis (BCO) in broilers. Fertile eggs from commercial breeder flocks were incubated and hatched at the University of Arkansas Poultry Research Hatchery. Male and female chicks were reared together (straight-run) or separately (sex-separate) in 3 × 3 m pens on litter or flat wire flooring with 65 (E1) or 60 (E2) birds per pen. Necropsies revealed lesions that are pathognomonic for BCO in ≥98% of the birds that became lame. The SigmaStat Z-test was used to compare cumulative BCO incidences through 8 wk of age. For birds reared on litter, the incidences of BCO were low regardless of cross or sex (range: 1.7 to 5.1%; P ≥ 0.6). Within a cross and sex, rearing the broilers straight-run versus sex-separate on wire flooring did not significantly affect the incidence of BCO. Significant incidences of BCO did not develop until after d 40. Males from the sire A cross developed a higher incidence of BCO than males from the sire B cross in E1 (27 vs. 17%, respectively; P = 0.009) but not in E2 (28.5 vs. 22.6%, respectively; P = 0.141). In both experiments, males from the sire A cross developed higher incidences of BCO than females from the sire B cross (27 vs. 11.9%, in E1; 28.5 vs. 14.8%, in E2). With the sexes pooled, broilers from the sire A cross consistently developed higher incidences of BCO than broilers from the sire B cross (21.4 vs. 14.9%, P = 0.005 in E1; 26.5 vs. 18.7%, P = 0.003 in E2). High susceptibilities to both femoral head (all femoral head necrosis = 66 to 85% incidences) and tibial head (all tibial head necrosis = 81 to 96% incidences) BCO lesions were demonstrated in lame birds from both sexes and crosses. This study supports a sire influence on the susceptibility of broilers to BCO. Sire lines can be chosen to reduce BCO susceptibility

Novel Straight Road Driving Control of Power Assisted Wheelchair Based on Disturbance Estimation of Right and Left Wheels

NASA Astrophysics Data System (ADS)

Seki, Hirokazu; Sugimoto, Takeaki; Tadakuma, Susumu

This paper describes a novel straight road driving control scheme of power assisted wheelchair. Power assisted wheelchair which assists the driving force by electric motors is expected to be widely used as a mobility support system for elderly people and disabled people. The straight driving can be prevented by the road conditions such as branches, grass and carpets because the right and left wheels drive independently. This paper proposes a straight road driving control system based on the disturbance torque estimation. The proposed system estimates the difference of the driving torque by disturbance torque observer and compensates to one side of the wheels. Some practical driving experiments on various road conditions show the effectiveness of the proposed control system.

Assessment of multiresolution segmentation for delimiting drumlins in digital elevation models.

PubMed

Eisank, Clemens; Smith, Mike; Hillier, John

2014-06-01

Mapping or "delimiting" landforms is one of geomorphology's primary tools. Computer-based techniques such as land-surface segmentation allow the emulation of the process of manual landform delineation. Land-surface segmentation exhaustively subdivides a digital elevation model (DEM) into morphometrically-homogeneous irregularly-shaped regions, called terrain segments. Terrain segments can be created from various land-surface parameters (LSP) at multiple scales, and may therefore potentially correspond to the spatial extents of landforms such as drumlins. However, this depends on the segmentation algorithm, the parameterization, and the LSPs. In the present study we assess the widely used multiresolution segmentation (MRS) algorithm for its potential in providing terrain segments which delimit drumlins. Supervised testing was based on five 5-m DEMs that represented a set of 173 synthetic drumlins at random but representative positions in the same landscape. Five LSPs were tested, and four variants were computed for each LSP to assess the impact of median filtering of DEMs, and logarithmic transformation of LSPs. The testing scheme (1) employs MRS to partition each LSP exhaustively into 200 coarser scales of terrain segments by increasing the scale parameter ( SP ), (2) identifies the spatially best matching terrain segment for each reference drumlin, and (3) computes four segmentation accuracy metrics for quantifying the overall spatial match between drumlin segments and reference drumlins. Results of 100 tests showed that MRS tends to perform best on LSPs that are regionally derived from filtered DEMs, and then log-transformed. MRS delineated 97% of the detected drumlins at SP values between 1 and 50. Drumlin delimitation rates with values up to 50% are in line with the success of manual interpretations. Synthetic DEMs are well-suited for assessing landform quantification methods such as MRS, since subjectivity in the reference data is avoided which increases the

Segmentation in Tardigrada and diversification of segmental patterns in Panarthropoda.

PubMed

Smith, Frank W; Goldstein, Bob

2017-05-01

The origin and diversification of segmented metazoan body plans has fascinated biologists for over a century. The superphylum Panarthropoda includes three phyla of segmented animals-Euarthropoda, Onychophora, and Tardigrada. This superphylum includes representatives with relatively simple and representatives with relatively complex segmented body plans. At one extreme of this continuum, euarthropods exhibit an incredible diversity of serially homologous segments. Furthermore, distinct tagmosis patterns are exhibited by different classes of euarthropods. At the other extreme, all tardigrades share a simple segmented body plan that consists of a head and four leg-bearing segments. The modular body plans of panarthropods make them a tractable model for understanding diversification of animal body plans more generally. Here we review results of recent morphological and developmental studies of tardigrade segmentation. These results complement investigations of segmentation processes in other panarthropods and paleontological studies to illuminate the earliest steps in the evolution of panarthropod body plans. Copyright © 2016 Elsevier Ltd. All rights reserved.

Biomechanical differences in the stem straightening process among Pinus pinaster provenances. A new approach for early selection of stem straightness.

PubMed

Sierra-de-Grado, Rosario; Pando, Valentín; Martínez-Zurimendi, Pablo; Peñalvo, Alejandro; Báscones, Esther; Moulia, Bruno

2008-06-01

Stem straightness is an important selection trait in Pinus pinaster Ait. breeding programs. Despite the stability of stem straightness rankings in provenance trials, the efficiency of breeding programs based on a quantitative index of stem straightness remains low. An alternative approach is to analyze biomechanical processes that underlie stem form. The rationale for this selection method is that genetic differences in the biomechanical processes that maintain stem straightness in young plants will continue to control stem form throughout the life of the tree. We analyzed the components contributing most to genetic differences among provenances in stem straightening processes by kinetic analysis and with a biomechanical model defining the interactions between the variables involved (Fournier's model). This framework was tested on three P. pinaster provenances differing in adult stem straightness and growth. One-year-old plants were tilted at 45 degrees, and individual stem positions and sizes were recorded weekly for 5 months. We measured the radial extension of reaction wood and the anatomical features of wood cells in serial stem cross sections. The integral effect of reaction wood on stem leaning was computed with Fournier's model. Responses driven by both primary and secondary growth were involved in the stem straightening process, but secondary-growth-driven responses accounted for most differences among provenances. Plants from the straight-stemmed provenance showed a greater capacity for stem straightening than plants from the sinuous provenances mainly because of (1) more efficient reaction wood (higher maturation strains) and (2) more pronounced secondary-growth-driven autotropic decurving. These two process-based traits are thus good candidates for early selection of stem straightness, but additional tests on a greater number of genotypes over a longer period are required.

Introduced T cell receptor variable region gene segments recombine in pre-B cells: evidence that B and T cells use a common recombinase.

PubMed

Yancopoulos, G D; Blackwell, T K; Suh, H; Hood, L; Alt, F W

1986-01-31

We have recently proposed that a common recombinase performs all of the many variable region gene assembly events in B and T cells, and that the specificity of these joining events is mediated by regulating the "accessibility" of the involved gene segments. To test this possibility, we have introduced "accessible" T cell receptor (TCR) variable region gene segments into a pre-B cell line capable of recombining endogenous and transfected immunoglobulin (Ig) variable region gene segments. Although the corresponding "inaccessible" endogenous TCR gene segments do not rearrange in this line or in B cells in general, the introduced TCR gene segments join very frequently and, in fact, closely resemble introduced Ig gene segments in their recombination characteristics. These observations suggest a new role for conventional Ig transcriptional enhancers--recombinational enhancement. Our studies provide insight into additional aspects of the joining mechanism such as N region insertion, aberrant joining, and recombination-recognition sequence requirements for joining.

Straight A's: Public Education Policy and Progress. Volume 6, Number 12

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2006-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) House Subcommittee Passes Education Funding Bill: Overall Education Spending Essentially Flat, Striving Readers…

Straight A's: Public Education Policy and Progress. Volume 8, Number 13

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2008-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Appropriations Process Underway...Sort Of: Senate Appropriations Committee Passes Education Funding Bill While House…

Straight A's: Public Education Policy and Progress. Volume 11, Number 9

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2011-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) "Engineering Solutions to the National Crisis in Literacy": Alliance Brief Calls for Alignment Between…

Straight A's: Public Education Policy and Progress. Volume 12, Number 2

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2012-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Waiving Away High School Graduation Rate Accountability?: State NCLB Waiver Proposals Threaten to Weaken…

Straight A's: Public Education Policy and Progress. Volume 12, Number 19

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2012-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Education Debate: Obama and Romney Highlight Education Positions During First Presidential Debate; (2)…

Straight A's: Public Education Policy and Progress. Volume 8, Number 2

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2008-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) "Educating Our Children": "Forbes" Taps Leaders in Business, Government, and Education for New…

Straight A's: Public Education Policy and Progress. Volume 4, Number 17

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2004-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) "Profiles in Leadership": Alliance Releases a Collection of Essays from America's Foremost Education…

How do patients with neglect see a horizontal line? Analysis of performances in coloured line bisection task.

PubMed

Misonou, Kaori; Ishiai, Sumio; Seki, Keiko; Koyama, Yasumasa; Nakano, Naomi

2004-06-01

Twelve patients with left unilateral spatial neglect were examined with a newly devised "coloured line bisection task". They were presented with a horizontal line printed in blue on one side and in red on the other side; the proportions of the blue and red segments were varied. Immediately after placement of the subjective midpoint, the line was concealed and the patients were asked to name the colours of the right and left ends. Five patients who identified the left-end colour almost correctly had no visual field defect, while the other seven whose colour naming was impaired on the left side had left visual field defect. The rightward bisection errors were similarly distributed in the fair and poor colour-naming patients except for two patients from the latter group. The lesions of the fair colour-naming patients spared the lingual and fusiform gyri, which are known to be engaged in colour processing. Patients with neglect whose visual field is preserved may neglect the leftward extension of a line but not the colour in the neglected space. The poor colour-naming patients frequently failed to name the left-end colour that appeared to the left of their subjective midpoint, which indicates that they hardly searched leftward beyond that point. In such trials, they reported that the left end had the same colour as the right end. The results suggest that in patients with neglect and left visual field defect, both the leftward extent and the colour of a line may be represented on the basis of the information from the attended right segment.

Heterologous Packaging Signals on Segment 4, but Not Segment 6 or Segment 8, Limit Influenza A Virus Reassortment.

PubMed

White, Maria C; Steel, John; Lowen, Anice C

2017-06-01

Influenza A virus (IAV) RNA packaging signals serve to direct the incorporation of IAV gene segments into virus particles, and this process is thought to be mediated by segment-segment interactions. These packaging signals are segment and strain specific, and as such, they have the potential to impact reassortment outcomes between different IAV strains. Our study aimed to quantify the impact of packaging signal mismatch on IAV reassortment using the human seasonal influenza A/Panama/2007/99 (H3N2) and pandemic influenza A/Netherlands/602/2009 (H1N1) viruses. Focusing on the three most divergent segments, we constructed pairs of viruses that encoded identical proteins but differed in the packaging signal regions on a single segment. We then evaluated the frequency with which segments carrying homologous versus heterologous packaging signals were incorporated into reassortant progeny viruses. We found that, when segment 4 (HA) of coinfecting parental viruses was modified, there was a significant preference for the segment containing matched packaging signals relative to the background of the virus. This preference was apparent even when the homologous HA constituted a minority of the HA segment population available in the cell for packaging. Conversely, when segment 6 (NA) or segment 8 (NS) carried modified packaging signals, there was no significant preference for homologous packaging signals. These data suggest that movement of NA and NS segments between the human H3N2 and H1N1 lineages is unlikely to be restricted by packaging signal mismatch, while movement of the HA segment would be more constrained. Our results indicate that the importance of packaging signals in IAV reassortment is segment dependent. IMPORTANCE Influenza A viruses (IAVs) can exchange genes through reassortment. This process contributes to both the highly diverse population of IAVs found in nature and the formation of novel epidemic and pandemic IAV strains. Our study sought to determine the

Heterologous Packaging Signals on Segment 4, but Not Segment 6 or Segment 8, Limit Influenza A Virus Reassortment

PubMed Central

White, Maria C.; Steel, John

2017-01-01

ABSTRACT Influenza A virus (IAV) RNA packaging signals serve to direct the incorporation of IAV gene segments into virus particles, and this process is thought to be mediated by segment-segment interactions. These packaging signals are segment and strain specific, and as such, they have the potential to impact reassortment outcomes between different IAV strains. Our study aimed to quantify the impact of packaging signal mismatch on IAV reassortment using the human seasonal influenza A/Panama/2007/99 (H3N2) and pandemic influenza A/Netherlands/602/2009 (H1N1) viruses. Focusing on the three most divergent segments, we constructed pairs of viruses that encoded identical proteins but differed in the packaging signal regions on a single segment. We then evaluated the frequency with which segments carrying homologous versus heterologous packaging signals were incorporated into reassortant progeny viruses. We found that, when segment 4 (HA) of coinfecting parental viruses was modified, there was a significant preference for the segment containing matched packaging signals relative to the background of the virus. This preference was apparent even when the homologous HA constituted a minority of the HA segment population available in the cell for packaging. Conversely, when segment 6 (NA) or segment 8 (NS) carried modified packaging signals, there was no significant preference for homologous packaging signals. These data suggest that movement of NA and NS segments between the human H3N2 and H1N1 lineages is unlikely to be restricted by packaging signal mismatch, while movement of the HA segment would be more constrained. Our results indicate that the importance of packaging signals in IAV reassortment is segment dependent. IMPORTANCE Influenza A viruses (IAVs) can exchange genes through reassortment. This process contributes to both the highly diverse population of IAVs found in nature and the formation of novel epidemic and pandemic IAV strains. Our study sought to

Straight A's: Public Education Policy and Progress. Volume 6, Number 6

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2006-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Senate Approves Budget Plan: Amendment Adds Funds for Education Programs; (2) The Hits Keep Coming: House…

Straight A's: Public Education Policy and Progress. Volume 12, Number 17

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2012-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) To Be Continued: Congress Enacts Temporary Funding Mechanism to Keep Government Operating Until March 2013; Bill…

Straight A's: Public Education Policy and Progress. Volume 10, Number 11

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2010

2010-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Turnaround or Full Speed Ahead?: House Committee Raises Concerns with School Turnaround Models Included in Obama…

Straight A's: Public Education Policy and Progress. Volume 7, Number 20

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2007-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Senate Begins Debate on Education Spending Bill: White House Threatens Presidential Veto; (2) NCLB Timetable in…

Straight A's: Public Education Policy and Progress. Volume 8, Number 1

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2008-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) NCLB Anniversary Prompts Renewed Calls for Reauthorization: Growth Models, High School Reform Emerge as Points of…

Straight A's: Public Education Policy and Progress. Volume 11, Number 1

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2011

2011-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Congress Delays Education Funding Decisions: Short-Term Measure Funds Government Into March, Ensures Greater Role for…

Straight A's: Public Education Policy and Progress. Volume 9, Number 16

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2009

2009-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Senate Committee Passes Education Appropriations Bill; (2) Upside Down: New Alliance Brief Says Federal Education…

Straight A's: Public Education Policy and Progress. Volume 11, Number 17

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2011-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Alliance President Bob Wise Named to "Nonprofit Times'" Top 50 Most Influential Executives; (2) Sound and…

Straight A's: Public Education Policy and Progress. Volume 11, Number 15

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2011-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Getting Down to Business: Obama Hosts Education Roundtable with Nation's Business Leaders; (2) "Diplomas Mean…

Straight A's: Public Education Policy and Progress. Volume 5, Number 8

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2005-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) New Report Offers Recommendations for Defining and Improving Graduation Rates: Calls for New Federal Funding Stream…

Trends in Canadian Newspaper Coverage of Gay-Straight Alliances, 2000-2009

ERIC Educational Resources Information Center

Herriot, Lindsay

2011-01-01

Gay-straight alliances (GSAs) in Canadian public schools have gained considerable attention from print media since reports first surfaced in the year 2000. This study tracked and analyzed Canadian newspaper reporting about GSA creation. It summarized the shift in public opinion toward lesbian, gay, bisexual, transgender, and queer (LGBTQ) youth…

Straight A's: Public Education Policy and Progress. Volume 6, Number 9

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2006-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) "Leaving Boys Behind": New Report Finds Higher High School Graduation Rates for Females Across Every Racial…

Straight A's: Public Education Policy and Progress. Volume 11, Number 5

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2011-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Waiting Game Continues for FY 2011 Appropriations: Short-Term Spending Measure Averts Government Shutdown, Postpones…

Straight A's: Public Education Policy and Progress. Volume 12, Number 15

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2012

2012-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) House Appropriations Subcommittee Sharpens Budget Knife: Subcommittee's Bill Would Cut Education Programs by $1.1…

Straight A's: Public Education Policy and Progress. Volume 12, Number 16

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2012-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Digital Learning Meets Digital Democracy: Alliance for Excellent Education Accepting Public Feedback on New Digital Learning…

Straight A's: Public Education Policy and Progress. Volume 9, Number 18

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2009

2009-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1)"Quality Education Too Long Delayed Is Education Denied": In Campaign-Like Speech, Secretary Duncan Turns Up…

Straight A's: Public Education Policy and Progress. Volume 9, Number 13

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2009

2009-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) "Standards Movement Gaining Steam": Duncan Announces Plan to Commit Up to $350 Million for Assessments…

Straight A's: Public Education Policy and Progress. Volume 10, Number 19

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2010

2010-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) To Be Continued: Congress Passes Continuing Resolution to Keep Government Running, Buys Time to Pass Appropriations…

Straight A's: Public Education Policy and Progress. Volume 5, Number 10

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2005

2005-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) How's the Water?: Congressional Hearing on High School Reform Recognizes the Crisis, but Urges Caution Before…

Straight A's: Public Education Policy and Progress. Volume 5, Number 12

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2005-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) House Committee Approves Education Funding Bill: Striving Readers Program Would Receive $5 Million Increase; (2) Role…

Restoration of outer segments of foveal photoreceptors after resolution of central serous chorioretinopathy.

PubMed

Ojima, Yumiko; Tsujikawa, Akitaka; Yamashiro, Kenji; Ooto, Sotaro; Tamura, Hiroshi; Yoshimura, Nagahisa

2010-01-01

To study morphologically and functionally the prognosis of damaged outer segments of the foveal photoreceptor layer in eyes with resolved central serous chorioretinopathy (CSC). We studied retrospectively the medical records of 70 patients (74 eyes) with resolved CSC. Optical coherence tomography was used to detect the junctions between inner and outer segments of the photoreceptors (IS/OS) as a hallmark of the integrity of the outer photoreceptor layer. In 53 eyes (71.6%), the IS/OS line was clearly detected beneath the fovea immediately after resolution of the retinal detachment, with good visual acuity (VA). In the remaining 21 eyes (28.4%), however, the foveal IS/OS line could not be detected shortly after resolution of CSC, and VA was variable, ranging from 0.1 to 1.5 (median, 0.9). Of these 21 eyes, 15 had a follow-up examination with OCT, and in four the foveal IS/OS line was not detected at the follow-up and vision in these eyes remained poor. However, nine eyes showed recovery of the foveal IS/OS line during follow-up, and these eyes had substantial visual recovery. Immediately after resolution of active CSC, although the IS/OS line cannot be detected beneath the fovea, it often shows restoration over time, with visual recovery, though in some eyes no restoration takes place and the prognosis remains poor.

Active Segmentation.

PubMed

Mishra, Ajay; Aloimonos, Yiannis

2009-01-01

The human visual system observes and understands a scene/image by making a series of fixations. Every fixation point lies inside a particular region of arbitrary shape and size in the scene which can either be an object or just a part of it. We define as a basic segmentation problem the task of segmenting that region containing the fixation point. Segmenting the region containing the fixation is equivalent to finding the enclosing contour- a connected set of boundary edge fragments in the edge map of the scene - around the fixation. This enclosing contour should be a depth boundary.We present here a novel algorithm that finds this bounding contour and achieves the segmentation of one object, given the fixation. The proposed segmentation framework combines monocular cues (color/intensity/texture) with stereo and/or motion, in a cue independent manner. The semantic robots of the immediate future will be able to use this algorithm to automatically find objects in any environment. The capability of automatically segmenting objects in their visual field can bring the visual processing to the next level. Our approach is different from current approaches. While existing work attempts to segment the whole scene at once into many areas, we segment only one image region, specifically the one containing the fixation point. Experiments with real imagery collected by our active robot and from the known databases 1 demonstrate the promise of the approach.

Random center vortex lines in continuous 3D space-time

DOE Office of Scientific and Technical Information (OSTI.GOV)

Höllwieser, Roman; Institute of Atomic and Subatomic Physics, Vienna University of Technology, Operngasse 9, 1040 Vienna; Altarawneh, Derar

2016-01-22

We present a model of center vortices, represented by closed random lines in continuous 2+1-dimensional space-time. These random lines are modeled as being piece-wise linear and an ensemble is generated by Monte Carlo methods. The physical space in which the vortex lines are defined is a cuboid with periodic boundary conditions. Besides moving, growing and shrinking of the vortex configuration, also reconnections are allowed. Our ensemble therefore contains not a fixed, but a variable number of closed vortex lines. This is expected to be important for realizing the deconfining phase transition. Using the model, we study both vortex percolation andmore » the potential V(R) between quark and anti-quark as a function of distance R at different vortex densities, vortex segment lengths, reconnection conditions and at different temperatures. We have found three deconfinement phase transitions, as a function of density, as a function of vortex segment length, and as a function of temperature. The model reproduces the qualitative features of confinement physics seen in SU(2) Yang-Mills theory.« less

Robotic Arm Comprising Two Bending Segments

NASA Technical Reports Server (NTRS)

Mehling, Joshua S.; Difler, Myron A.; Ambrose, Robert O.; Chu, Mars W.; Valvo, Michael C.

2010-01-01

The figure shows several aspects of an experimental robotic manipulator that includes a housing from which protrudes a tendril- or tentacle-like arm 1 cm thick and 1 m long. The arm consists of two collinear segments, each of which can be bent independently of the other, and the two segments can be bent simultaneously in different planes. The arm can be retracted to a minimum length or extended by any desired amount up to its full length. The arm can also be made to rotate about its own longitudinal axis. Some prior experimental robotic manipulators include single-segment bendable arms. Those arms are thicker and shorter than the present one. The present robotic manipulator serves as a prototype of future manipulators that, by virtue of the slenderness and multiple- bending capability of their arms, are expected to have sufficient dexterity for operation within spaces that would otherwise be inaccessible. Such manipulators could be especially well suited as means of minimally invasive inspection during construction and maintenance activities. Each of the two collinear bending arm segments is further subdivided into a series of collinear extension- and compression-type helical springs joined by threaded links. The extension springs occupy the majority of the length of the arm and engage passively in bending. The compression springs are used for actively controlled bending. Bending is effected by means of pairs of antagonistic tendons in the form of spectra gel spun polymer lines that are attached at specific threaded links and run the entire length of the arm inside the spring helix from the attachment links to motor-driven pulleys inside the housing. Two pairs of tendons, mounted in orthogonal planes that intersect along the longitudinal axis, are used to effect bending of each segment. The tendons for actuating the distal bending segment are in planes offset by an angle of 45 from those of the proximal bending segment: This configuration makes it possible to

Production and Identification of Wheat-Agropyron cristatum 2P Translocation Lines

PubMed Central

Li, Huanhuan; Lv, Mingjie; Song, Liqiang; Zhang, Jinpeng; Gao, Ainong; Li, Lihui; Liu, Weihua

2016-01-01

Agropyron cristatum (L.) Gaertn. (2n = 28, PPPP), a wild relative of common wheat, possesses many potentially valuable traits that can be transferred to common wheat through breeding programs. The wheat-A. cristatum disomic addition and translocation lines can be used as bridge materials to introduce alien chromosomal segments to wheat. Wheat-A. cristatum 2P disomic addition line II-9-3 was highly resistant to powdery mildew and leaf rust, which was reported in our previous study. However, some translocation lines induced from II-9-3 have not been reported. In this study, some translocation lines were induced from II-9-3 by 60Co-γ irradiation and gametocidal chromosome 2C and then identified by cytological methods. Forty-nine wheat-A. cristatum translocation lines were obtained and various translcoation types were identified by GISH (genomic in situ hybridization), such as whole-arm, segmental and intercalary translocations. Dual-color FISH (fluorescent in situ hybridization) was applied to identify the wheat chromosomes involved in the translocations, and the results showed that A. cristatum 2P chromosome segments were translocated to the different wheat chromosomes, including 1A, 2A, 3A, 4A, 5A, 6A, 7A, 3B, 5B, 7B, 1D, 4D and 6D. Many different types of wheat-A. cristatum alien translocation lines would be valuable for not only identifying and cloning A. cristatum 2P-related genes and understanding the genetics and breeding effects of the translocation between A. cristatum chromosome 2P and wheat chromosomes, but also providing new germplasm resources for the wheat genetic improvement. PMID:26731742

Straight A's: Public Education Policy and Progress. Volume 11, Number 22

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2011-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Deficit Committee's Failure Triggers Automatic Spending Cuts: Education Programs Could Face $3.5 Billion in Cuts; (2)…

Straight A's: Public Education Policy and Progress. Volume 4, Number 6

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2004-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Improving the Lives of Our High School Students: Alliance and Scholastic Co-Host Invitational High School Literacy…

Straight A's: Public Education Policy and Progress. Volume 8, Number 18

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2008-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Congress Punts Education Funding Decision to 2009: Education and Other Domestic Priorities Frozen While Defense and Homeland…

Straight A's: Public Education Policy and Progress. Volume 10, Number 21

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2010

2010-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Divided We Stall?: Prospects for Education Reform Unclear After Republicans Take Control in the House of Representatives, Gain…

Straight A's: Public Education Policy and Progress. Volume 8, Number 19

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2008-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) "A Tipping Point in Education": Report Finds Educational Attainment of Younger Generations Has Not Increased; (2) Building a…

Straight A's: Public Education Policy and Progress. Volume 7, Number 13

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2007-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) "A Plan for Success": Alliance Joins Nine National Organizations Representing Communities of Color in Historic Campaign for…

Straight A's: Public Education Policy and Progress. Volume 10, Number 2

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2010

2010-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) "The High Cost of Low Educational Performance": New OECD Report Finds that 25 Point Increase in PISA Scores…

Straight A's: Public Education Policy and Progress. Volume 6, Number 16

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2006-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Paying Double: United States Spends Over $1.4 Billion Annually on Remedial Education for Recent High School…

Straight A's: Public Education Policy and Progress. Volume 10, Number 1

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2010

2010-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Education Appropriations Bill Signed into Law: U.S. Department of Education to Receive $1 Billion Increase in…

Straight A's: Public Education Policy and Progress. Volume 6, Number 11

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2006-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) House Passes Budget Resolution: Prospects of a Compromise with the Senate Appear Dim; (2) Older Students' Science…

Straight A's: Public Education Policy and Progress. Volume 11, Number 21

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2011-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Nation's Report Card Reveals Modest Increases in Math and Reading: Report Shows One-Quarter of Eighth Graders Reading…

Straight A's: Public Education Policy and Progress. Volume 10, Number 10

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2010

2010-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) ESEA [Elementary and Secondary Education Act] Reauthorization Shifts to Middle and High Schools: Senate HELP [Health,…

Straight A's: Public Education Policy and Progress. Volume 9, Number 19

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2009

2009-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Stimulus Shell Game?: U.S. Department of Education's Inspector General Warns that Some States are Using Education…

Straight A's: Public Education Policy and Progress. Volume 11, Number 13

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2011-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Wave Goodbye to Waivers?: Key House Republicans Challenge Duncan's Plan to Grant Waivers to NCLB Requirements; (2)…

Straight A's: Public Education Policy and Progress. Volume 11, Number 23

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2011-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) All I Want for Christmas: Congress Continues Deliberations on Fiscal Year 2012 Funding; Education Programs Potentially Facing…

Straight A's: Public Education Policy and Progress. Volume 9, Number 8

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2009

2009-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Duncan Makes $44 Billion in Education Funding Available to States: Education Secretary Says Stimulus Money Must Go…

Straight A's: Public Education Policy and Progress. Volume 11, Number 19

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2011-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) U.S. Senators Harkin and Enzi Release Draft Language to Revise NCLB: Senate Committee to Consider Draft Containing…

Straight A's: Public Education Policy and Progress. Volume 7, Number 8

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2007-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) "The Gap Defined": ACT Report Cites Poor State Standards and Assessments as Possible Reason for Gap Between Postsecondary…

Straight A's: Public Education Policy and Progress. Volume 9, Number 15

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2009

2009-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Race to the Top: Obama, Duncan Outline Requirements of $4.35 Billion Program; (2) "Preparing the Workers of…

Straight A's: Public Education Policy and Progress. Volume 11, Number 7

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2011-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) FY 2011 Spending Discussions Continue: Pressure Mounts as April 8 Deadline Approaches and Possibility of Government Shutdown…

Straight A's: Public Education Policy and Progress. Volume 11, Number 6

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2011-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Obama Sets Timeline for NCLB Revamp: President Calls on Congress to Send Him an Education Reform Bill "Before…

Straight A's: Public Education Policy and Progress. Volume 7, Number 21

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2007-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Focus on Dropout Factories: Associated Press Article Spotlights Low-Performing High Schools, Draws Criticism from Many School…

Straight A's: Public Education Policy and Progress. Volume 10, Number 3

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2010

2010-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Obama Releases FY 2011 Budget: Obama's 7.5 Percent Increase for Education Programs Signals Commitment to Reauthorize…

Straight A's: Public Education Policy and Progress. Volume 4, Number 9

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2004-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Graduation for All, A Right and a Responsibility: National Campaign to Focus on Increasing High School Graduation…

Straight A's: Public Education Policy and Progress. Volume 10, Number 18

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2010

2010-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) From Gathering Storm to Category 5: Five Years After "Rising Above the Gathering Storm", U.S. Competitive…

Formation of the insect head involves lateral contribution of the intercalary segment, which depends on Tc-labial function.

PubMed

Posnien, Nico; Bucher, Gregor

2010-02-01

The insect head is composed of several segments. During embryonic development, the segments fuse to form a rigid head capsule where obvious segmental boundaries are lacking. Hence, the assignment of regions of the insect head to specific segments is hampered, especially with respect to dorsal (vertex) and lateral (gena) parts. We show that upon Tribolium labial (Tc-lab) knock down, the intercalary segment is deleted but not transformed. Furthermore, we find that the intercalary segment contributes to lateral parts of the head cuticle in Tribolium. Based on several additional mutant and RNAi phenotypes that interfere with gnathal segment development, we show that these segments do not contribute to the dorsal head capsule apart from the dorsal ridge. Opposing the classical view but in line with findings in the vinegar fly Drosophila melanogaster and the milkweed bug Oncopeltus fasciatus, we propose a "bend and zipper" model for insect head capsule formation.

Main doorway to the display area, straight ahead. Double doors ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Main doorway to the display area, straight ahead. Double doors with "top secret" alert lights, coded doorbell, and one way mirror. Stairway to second floor and basement is at the left, as well as the secondary entrance at the east part of the north front. View to east - March Air Force Base, Strategic Air Command, Combat Operations Center, 5220 Riverside Drive, Moreno Valley, Riverside County, CA

GeoSegmenter: A statistically learned Chinese word segmenter for the geoscience domain

NASA Astrophysics Data System (ADS)

Huang, Lan; Du, Youfu; Chen, Gongyang

2015-03-01

Unlike English, the Chinese language has no space between words. Segmenting texts into words, known as the Chinese word segmentation (CWS) problem, thus becomes a fundamental issue for processing Chinese documents and the first step in many text mining applications, including information retrieval, machine translation and knowledge acquisition. However, for the geoscience subject domain, the CWS problem remains unsolved. Although a generic segmenter can be applied to process geoscience documents, they lack the domain specific knowledge and consequently their segmentation accuracy drops dramatically. This motivated us to develop a segmenter specifically for the geoscience subject domain: the GeoSegmenter. We first proposed a generic two-step framework for domain specific CWS. Following this framework, we built GeoSegmenter using conditional random fields, a principled statistical framework for sequence learning. Specifically, GeoSegmenter first identifies general terms by using a generic baseline segmenter. Then it recognises geoscience terms by learning and applying a model that can transform the initial segmentation into the goal segmentation. Empirical experimental results on geoscience documents and benchmark datasets showed that GeoSegmenter could effectively recognise both geoscience terms and general terms.

Unraveling Pancreatic Segmentation.

PubMed

Renard, Yohann; de Mestier, Louis; Perez, Manuela; Avisse, Claude; Lévy, Philippe; Kianmanesh, Reza

2018-04-01

Limited pancreatic resections are increasingly performed, but the rate of postoperative fistula is higher than after classical resections. Pancreatic segmentation, anatomically and radiologically identifiable, may theoretically help the surgeon removing selected anatomical portions with their own segmental pancreatic duct and thus might decrease the postoperative fistula rate. We aimed at systematically and comprehensively reviewing the previously proposed pancreatic segmentations and discuss their relevance and limitations. PubMed database was searched for articles investigating pancreatic segmentation, including human or animal anatomy, and cadaveric or surgical studies. Overall, 47/99 articles were selected and grouped into 4 main hypotheses of pancreatic segmentation methodology: anatomic, vascular, embryologic and lymphatic. The head, body and tail segments are gross description without distinct borders. The arterial territories defined vascular segments and isolate an isthmic paucivascular area. The embryological theory relied on the fusion plans of the embryological buds. The lymphatic drainage pathways defined the lymphatic segmentation. These theories had differences, but converged toward separating the head and body/tail parts, and the anterior from posterior and inferior parts of the pancreatic head. The rate of postoperative fistula was not decreased when surgical resection was performed following any of these segmentation theories; hence, none of them appeared relevant enough to guide pancreatic transections. Current pancreatic segmentation theories do not enable defining anatomical-surgical pancreatic segments. Other approaches should be explored, in particular focusing on pancreatic ducts, through pancreatic ducts reconstructions and embryologic 3D modelization.

Comparison of enterotomy leak pressure among fresh, cooled, and frozen-thawed porcine jejunal segments.

PubMed

Aeschlimann, Kimberly A; Mann, F A; Middleton, John R; Belter, Rebecca C

2018-05-01

OBJECTIVE To determine whether stored (cooled or frozen-thawed) jejunal segments can be used to obtain dependable leak pressure data after enterotomy closure. SAMPLE 36 jejunal segments from 3 juvenile pigs. PROCEDURES Jejunal segments were harvested from euthanized pigs and assigned to 1 of 3 treatment groups (n = 12 segments/group) as follows: fresh (used within 4 hours after collection), cooled (stored overnight at 5°C before use), and frozen-thawed (frozen at -12°C for 8 days and thawed at room temperature [23°C] for 1 hour before use). Jejunal segments were suspended and 2-cm enterotomy incisions were made on the antimesenteric border. Enterotomies were closed with a simple continuous suture pattern. Lactated Ringer solution was infused into each segment until failure at the suture line was detected. Leak pressure was measured by use of a digital transducer. RESULTS Mean ± SD leak pressure for fresh, cooled, and frozen-thawed segments was 68.3 ± 23.7 mm Hg, 55.3 ± 28.1 mm Hg, and 14.4 ± 14.8 mm Hg, respectively. Overall, there were no significant differences in mean leak pressure among pigs, but a significant difference in mean leak pressure was detected among treatment groups. Mean leak pressure was significantly lower for frozen-thawed segments than for fresh or cooled segments, but mean leak pressure did not differ significantly between fresh and cooled segments. CONCLUSIONS AND CLINICAL RELEVANCE Fresh porcine jejunal segments or segments cooled overnight may be used for determining intestinal leak pressure, but frozen-thawed segments should not be used.

Alignment and Integration Techniques for Mirror Segment Pairs on the Constellation X Telescope

NASA Technical Reports Server (NTRS)

Hadjimichael, Theo; Lehan, John; Olsen, Larry; Owens, Scott; Saha, Timo; Wallace, Tom; Zhang, Will

2007-01-01

We present the concepts behind current alignment and integration techniques for testing a Constellation-X primary-secondary mirror segment pair in an x-ray beam line test. We examine the effects of a passive mount on thin glass x-ray mirror segments, and the issues of mount shape and environment on alignment. We also investigate how bonding and transfer to a permanent housing affects the quality of the final image, comparing predicted results to a full x-ray test on a primary secondary pair.

Effect of splitting a mixed-model line on shortening the line length under open- and closed-boundary working area settings

NASA Astrophysics Data System (ADS)

Zhang, Donghao; Matsuura, Haruki; Asada, Akiko

2017-04-01

Some automobile factories have segmented mixed-model production lines into shorter sub-lines according to part group, such as engine, trim, and powertrain. The effects of splitting a line into sub-lines have been reported from the standpoints of worker motivation, productivity improvement, and autonomy based on risk spreading. There has been no mention of the possibility of shortening the line length by altering the product sequence using sub-lines. The purpose of the present paper is to determine the conditions under which sub-lines reduce the line length and the degree to which the line length may be shortened. The line lengths for a non-split line and a line that has been split into sub-lines are compared using three methods for determining the working area, the standard closed boundary, the optimized open boundary, and real-life constant-length stations. The results are discussed by analyzing the upper and lower bounds of the line length. Based on these results, a procedure for deciding whether or not to split a production line is proposed.

Wind tunnel study of helical and straight-bladed vertical-axis wind turbine wakes

NASA Astrophysics Data System (ADS)

Bagheri, Maryam; Araya, Daniel

2017-11-01

It is hypothesized that blade curvature can serve as a passive means to control fluid entrainment and wake recovery in vertical-axis wind turbine (VAWT) arrays. We test this experimentally in a wind tunnel using two different VAWT configurations, one with straight blades and another with helical blades, keeping all other experimental parameters fixed. A small-scale, commercially available VAWT (15W max power) is used as the baseline wind tunnel model in each case. The commercial VAWT blades are replaced with either straight or helical blades that are 3D-printed extrusions of the same airfoil cross-section. Results from smoke flow visualization, three-component wake velocity measurements, and turbine power data are presented. These results give insight into the potential use of VAWTs with curved blades in utility-scale wind farms.

Unzip instabilities: Straight to oscillatory transitions in the cutting of thin polymer sheets

NASA Astrophysics Data System (ADS)

Reis, P. M.; Kumar, A.; Shattuck, M. D.; Roman, B.

2008-06-01

We report an experimental investigation of the cutting of a thin brittle polymer sheet with a blunt tool. It was recently shown that the fracture path becomes oscillatory when the tool is much wider than the sheet thickness. Here we uncover two novel transitions from straight to oscillatory fracture by varying either the tilt angle of the tool or the speed of cutting, respectively. We denote these by angle and speed unzip instabilities and analyze them by quantifying both the dynamics of the crack tip and the final shapes of the fracture paths. Moreover, for the speed unzip instability, the straight crack lip obtained at low speeds exhibits out-of-plane buckling undulations (as opposed to being flat above the instability threshold) suggesting a transition from ductile to brittle fracture.

Straight-wire appliances: standard versus individual prescription.

PubMed

Farronato, Giampietro; Periti, Giulia; Giannini, Lucia; Farronato, Davide; Maspero, Cinzia

2009-01-01

In this article the individual patient (IP) appliance is described. It consists of 250 options of bracket and band variations as the straight wire appliances. Increasing the bracket capabilities means using an increasing number of brackets, each with a specific design created for a treatment situation. The objective of IP appliance is to eliminate wire bending from orthodontic treatment and improve the treatment results. To manage this technique, a computer software is needed. Internet offers significant possibilities in managing each patient by patient basis. The clinician is required to make the diagnosis and treatment plan before ordering the appliance. Two clinical cases are described with the aim to present the advantages of this technique.

Straight A's: Public Education Policy and Progress. Volume 4, Number 19

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2004-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Four More Years: Bush to Focus on High Schools During Second Term; (2) Education Funding Still in Limbo: Congress to…

Straight A's: Public Education Policy and Progress. Volume 5, Number 9

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2005-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Americans Speak on Education: Public Credits Education System for U.S. Success in the World, but Worries About Future…

Straight A's: Public Education Policy and Progress. Volume 6, Number 23

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2006-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) See You Next Year: Congress Wraps Up for 2006, Delays Education Funding Decisions to 2007; (2) "Healthier and Wealthier":…

Straight A's: Public Education Policy and Progress. Volume 6, Number 2

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2006-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) State of American Business: U.S. Chamber of Commerce Says U.S. Could Face a "Severe Worker Shortage" Unless…

A Program Review of a Middle School Gay-Straight Alliance Club

ERIC Educational Resources Information Center

Quasha, Scott; McCabe, Paul C.; Ortiz, Samuel O.

2014-01-01

This program review examined a middle school Gay-Straight Alliance (GSA) club within a northeastern suburban school situated in a large metropolitan area. The GSA was the first in the region to start exclusively in a standalone middle school. The review was accomplished through a staff survey comparing school climates for lesbian, gay, bisexual,…

Straight A's: Public Education Policy and Progress. Volume 12, Number 7

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2012-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Problems Down the Road: House Passes Congressional Budget Resolutions, Sets Overall Spending Cap at $19 Billion Below Senate;…

Straight A's: Public Education Policy and Progress. Volume 11, Number 4

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2011-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) House Passes FY 2011 Spending Bill: Bill Cuts U.S. Department of Education Funding by $5 Billion; Title I, School…

Straight A's: Public Education Policy and Progress. Volume 8, Number 6

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2008-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) House and Senate Pass Budget Blueprints: Plans Would Increase Spending by More than $20 Billion Over the President's…

Straight A's: Public Education Policy and Progress. Volume 12, Number 21

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2012-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Four More Years: Obama Wins Re-election, Plans to Continue Education Reforms Through Race to the Top, NCLB Waivers;…

Straight A's: Public Education Policy and Progress. Volume 11, Number 11

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2011-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) A Time for Deeper Learning: New Alliance Brief Says Deeper Learning Is Imperative for All Students; (2) Setting New…

Straight A's: Public Education Policy and Progress. Volume 6, Number 8

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2006-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) House Leaders Unable to Come to Agreement on a Budget Plan: Interparty Fights Postpone Consideration of the Budget Resolution;…

Straight A's: Public Education Policy and Progress. Volume 9, Number 23

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2009

2009-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Two Omnibus Bills and a Partridge in a Pear Tree?: Final Vote on Education Appropriations Bill Could Come Before…

Automatic segmentation of equine larynx for diagnosis of laryngeal hemiplegia

NASA Astrophysics Data System (ADS)

Salehin, Md. Musfequs; Zheng, Lihong; Gao, Junbin

2013-10-01

This paper presents an automatic segmentation method for delineation of the clinically significant contours of the equine larynx from an endoscopic image. These contours are used to diagnose the most common disease of horse larynx laryngeal hemiplegia. In this study, hierarchal structured contour map is obtained by the state-of-the-art segmentation algorithm, gPb-OWT-UCM. The conic-shaped outer boundary of equine larynx is extracted based on Pascal's theorem. Lastly, Hough Transformation method is applied to detect lines related to the edges of vocal folds. The experimental results show that the proposed approach has better performance in extracting the targeted contours of equine larynx than the results of using only the gPb-OWT-UCM method.

Implicit and explicit measures of sexual orientation attitudes: in group preferences and related behaviors and beliefs among gay and straight men.

PubMed

Jellison, William A; McConnell, Allen R; Gabriel, Shira

2004-05-01

The relations among implicit and explicit measures of sexual orientation attitudes and sexual-orientation-related behavior and beliefs among gay men (Study 1) and straight men (Studies 1 and 2) were explored. Study 1 found relations between implicit and explicit measures of sexual orientation attitudes, large differences between gay and straight men on both implicit and explicit measures, and that these measures predicted sexual-orientation-related behaviors among gay men. Also, only straight men exhibited a negative relation between their attitudes toward homosexuality and heterosexuality. Study 2 found that as straight men held more negative attitudes toward homosexuality, they more strongly endorsed the importance of heterosexual identity and of traditional masculine gender roles. These endorsements mediated the negative relation between their attitudes toward heterosexuality and homosexuality. Implications for assessing attitudes toward sexual orientation and their relations for sexual orientation identity are discussed.

Optimization of Straight Cylindrical Turning Using Artificial Bee Colony (ABC) Algorithm

NASA Astrophysics Data System (ADS)

Prasanth, Rajanampalli Seshasai Srinivasa; Hans Raj, Kandikonda

2017-04-01

Artificial bee colony (ABC) algorithm, that mimics the intelligent foraging behavior of honey bees, is increasingly gaining acceptance in the field of process optimization, as it is capable of handling nonlinearity, complexity and uncertainty. Straight cylindrical turning is a complex and nonlinear machining process which involves the selection of appropriate cutting parameters that affect the quality of the workpiece. This paper presents the estimation of optimal cutting parameters of the straight cylindrical turning process using the ABC algorithm. The ABC algorithm is first tested on four benchmark problems of numerical optimization and its performance is compared with genetic algorithm (GA) and ant colony optimization (ACO) algorithm. Results indicate that, the rate of convergence of ABC algorithm is better than GA and ACO. Then, the ABC algorithm is used to predict optimal cutting parameters such as cutting speed, feed rate, depth of cut and tool nose radius to achieve good surface finish. Results indicate that, the ABC algorithm estimated a comparable surface finish when compared with real coded genetic algorithm and differential evolution algorithm.

Chain-Wise Generalization of Road Networks Using Model Selection

NASA Astrophysics Data System (ADS)

Bulatov, D.; Wenzel, S.; Häufel, G.; Meidow, J.

2017-05-01

Streets are essential entities of urban terrain and their automatized extraction from airborne sensor data is cumbersome because of a complex interplay of geometric, topological and semantic aspects. Given a binary image, representing the road class, centerlines of road segments are extracted by means of skeletonization. The focus of this paper lies in a well-reasoned representation of these segments by means of geometric primitives, such as straight line segments as well as circle and ellipse arcs. We propose the fusion of raw segments based on similarity criteria; the output of this process are the so-called chains which better match to the intuitive perception of what a street is. Further, we propose a two-step approach for chain-wise generalization. First, the chain is pre-segmented using circlePeucker and finally, model selection is used to decide whether two neighboring segments should be fused to a new geometric entity. Thereby, we consider both variance-covariance analysis of residuals and model complexity. The results on a complex data-set with many traffic roundabouts indicate the benefits of the proposed procedure.

A new method named as Segment-Compound method of baffle design

NASA Astrophysics Data System (ADS)

Qin, Xing; Yang, Xiaoxu; Gao, Xin; Liu, Xishuang

2017-02-01

As the observation demand increased, the demand of the lens imaging quality rising. Segment- Compound baffle design method was proposed in this paper. Three traditional methods of baffle design they are characterized as Inside to Outside, Outside to Inside, and Mirror Symmetry. Through a transmission type of optical system, the four methods were used to design stray light suppression structure for it, respectively. Then, structures modeling simulation with Solidworks, CAXA, Tracepro, At last, point source transmittance (PST) curve lines were got to describe their performance. The result shows that the Segment- Compound method can inhibit stay light more effectively. Moreover, it is easy to active and without use special material.

Straight A's: Public Education Policy and Progress. Volume 11, Number 8

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2011-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Last Cut Is the Deepest: Final FY 2011 Spending Agreement Cuts Spending by Nearly $40 Billion, Includes More Cuts for Education…

Straight A's: Public Education Policy and Progress. Volume 12, Number 9

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2012-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) You Take the High Road and I'll Take the Low Road: As Appropriations Process Begins, Different Spending Approaches Likely to…

Straight A's: Public Education Policy and Progress. Volume 10, Number 23

ERIC Educational Resources Information Center

Alliance for Excellent Education, 2010

2010-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Getting Back to Average: American Fifteen-Year-Olds Rank 14th in Reading, 17th in Science, and 25th in Mathematics,…

Straight A's: Public Education Policy and Progress. Volume 8, Number 21

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2008-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Yes He Will?: Campaign Details Suggest That Obama Presidency Will Make Education Reform a High Priority; (2) A New Way Forward…

Straight A's: Public Education Policy and Progress. Volume 12, Number 8

ERIC Educational Resources Information Center

Amos, Jason, Ed.

2012-01-01

"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Tax Returns: On Tax Day 2012, a 90 Percent High School Graduation Rate Would Yield $1.8 Billion Annually in Additional Tax…

Hydrogeomorphological variability and ecological impacts in straight and restored river reach sections

NASA Astrophysics Data System (ADS)

Schäppi, B.; Molnar, P.; Perona, P.; Tockner, K.; Burlando, P.

2009-04-01

Healthy floodplain ecosystems are characterized by high habitat diversity which tends to be lost in straightened channelized rivers. River restoration projects aim to increase habitat heterogeneity by re-establishing natural flow conditions and/or re-activating geomorphic processes in straightened reaches. The success of such projects is usually measured by means of structural and functional hydrogeomorphic and ecological indicators. Important indicators include flow variables and morphological features such as flow depth, velocity, shore line length, exposed gravel area and wetted river width. Also important are the rates at which these variables and features change under varying streamflow. A high spatial variability in the indicators is generally connected with high habitat diversity. The temporal availability and spatial distribution of both aquatic and riparian habitats control the composition and diversity of benthic organisms, fish, and riparian communities. Spatial heterogeneity provides refugia, i.e. areas from which recolonization after a disturbance event may occur. In addition, it facilitates the transfer of organisms and matter across the aquatic and terrestrial interface, thereby increasing the overall functional performance of coupled river-riparian ecosystems. However the habitat diversity can be maintained over time only if there are frequent disturbances such as periodic floods that reset the system and create new germination sites for pioneer vegetation and rework the channel bed to form new aquatic habitat. Therefore the flow and morphology indicators need to be investigated on spatial as well as on temporal scales. Traditionally, these indicators are measured in the field albeit most measurements can be carried out only at low flow conditions. We propose that flow simulations with a 2d hydrodynamic model may be used for a fast and convenient assessment of indicators of flow variables and morphological features with relatively little calibration

Computational efficient segmentation of cell nuclei in 2D and 3D fluorescent micrographs

NASA Astrophysics Data System (ADS)

De Vylder, Jonas; Philips, Wilfried

2011-02-01

This paper proposes a new segmentation technique developed for the segmentation of cell nuclei in both 2D and 3D fluorescent micrographs. The proposed method can deal with both blurred edges as with touching nuclei. Using a dual scan line algorithm its both memory as computational efficient, making it interesting for the analysis of images coming from high throughput systems or the analysis of 3D microscopic images. Experiments show good results, i.e. recall of over 0.98.

Chemical Burn-Induced Stromal Demarcation Line.

PubMed

Brosh, Koby; Rozenman, Yaacov

2016-02-01

A stromal demarcation line is a well-known sign after collagen cross-linking. It has been proposed that this line is the transition zone between cellular and acellular stroma, and thus it might reveal the depth of photochemical changes in the corneal stroma. We report 2 cases of a similar demarcation line after chemical alkali burns. To the best of our knowledge, this is the first report of a stromal demarcation line after a chemical burn. Two patients presented to the emergency department after an ocular alkali burn. At presentation, both had total corneal erosion, corneal edema, and limbal ischemia. After 12 to 15 days, a stromal line was apparent by both slit-lamp examination and anterior segment optical coherence tomography. The stromal demarcation lines disappeared approximately 3 months after the injury. A stromal demarcation line may appear not only after collagen cross-linking but also after a chemical burn. The line depth may be associated with the severity of the injury, and therefore, may have prognostic significance. Patients with chemical burns should be examined for evidence of a stromal line in the cornea.

Movement of the sacroiliac joint during the Active Straight Leg Raise test in patients with long-lasting severe sacroiliac joint pain.

PubMed

Kibsgård, Thomas J; Röhrl, Stephan M; Røise, Olav; Sturesson, Bengt; Stuge, Britt

2017-08-01

The Active Straight Leg Raise is a functional test used in the assessment of pelvic girdle pain, and has shown to have good validity, reliability and responsiveness. The Active Straight Leg Raise is considered to examine the patients' ability to transfer load through the pelvis. It has been hypothesized that patients with pelvic girdle pain lack the ability to stabilize the pelvic girdle, probably due to instability or increased movement of the sacroiliac joint. This study examines the movement of the sacroiliac joints during the Active Straight Leg Raise in patients with pelvic girdle pain. Tantalum markers were inserted in the dorsal sacrum and ilium of 12 patients with long-lasting pelvic girdle pain scheduled for sacroiliac joint fusion surgery. Two to three weeks later movement of the sacroiliac joints during the Active Straight Leg Raise was measured with radiostereometric analysis. Small movements were detected. There was larger movement of the sacroiliac joint of the rested leg's sacroiliac joint compared to the lifted leg's side. A mean backward rotation of 0.8° and inward tilt of 0.3° were seen in the rested leg's sacroiliac joint. The movements of the sacroiliac joints during the Active Straight Leg Raise are small. There was a small backward rotation of the innominate bone relative to sacrum on the rested leg's side. Our findings contradict an earlier understanding that a forward rotation of the lifted leg's innominate occur while performing the Active Straight Leg Raise. Copyright © 2017. Published by Elsevier Ltd.

Cascaded Segmentation-Detection Networks for Word-Level Text Spotting.

PubMed

Qin, Siyang; Manduchi, Roberto

2017-11-01

We introduce an algorithm for word-level text spotting that is able to accurately and reliably determine the bounding regions of individual words of text "in the wild". Our system is formed by the cascade of two convolutional neural networks. The first network is fully convolutional and is in charge of detecting areas containing text. This results in a very reliable but possibly inaccurate segmentation of the input image. The second network (inspired by the popular YOLO architecture) analyzes each segment produced in the first stage, and predicts oriented rectangular regions containing individual words. No post-processing (e.g. text line grouping) is necessary. With execution time of 450 ms for a 1000 × 560 image on a Titan X GPU, our system achieves good performance on the ICDAR 2013, 2015 benchmarks [2], [1].

Magnifying endoscopy for the diagnosis of specialized intestinal metaplasia in short-segment Barrett's esophagus.

PubMed

Ham, Nam Seok; Jang, Jae Young; Ryu, Sung Woo; Kim, Ji Hye; Park, Eui Ju; Lee, Woong Cheul; Shim, Kwang Yeun; Jeong, Soung Won; Kim, Hyun Gun; Lee, Tae Hee; Jeon, Sung Ran; Cho, Jun Hyung; Cho, Joo Young; Jin, So Young; Lee, Ji Sung

2013-11-07

To determine whether magnified observation of short-segment Barrett's esophagus (BE) is useful for the detection of specialized intestinal metaplasia (SIM). Thirty patients with suspected short-segment BE underwent magnifying endoscopy up to × 80. The magnified images were analyzed with respect to their pit-patterns, which were simultaneously classified into five epithelial types [I (small round), II (straight), III (long oval), IV (tubular), V (villous)] by Endo's classification. Then, a 0.5% solution of methylene blue (MB) was sprayed over columnar mucosa. The patterns of the magnified image and MB staining were analyzed. Biopsies were obtained from the regions previously observed by magnifying endoscopy and MB chromoendoscopy. Three of five patients with a type V (villous) epithelial pattern had SIM, whereas 21 patients with a non-type V epithelial patterns did not have SIM. The sensitivity, specificity, accuracy, positive predictive value, and negative predictive value of pit-patterns in detecting SIM were 100%, 91.3%, 92.3%, 60% and 100%, respectively (P = 0.004). Three of the 12 patients with positive MB staining had SIM, whereas 14 patients with negative MB staining did not have SIM. The sensitivity, specificity, accuracy, positive predictive value, and negative predictive value of MB staining in detecting SIM were 100%, 60.9%, 65.4%, 25% and 100%, respectively (P = 0.085). The specificity and accuracy of pit-pattern evaluation were significantly superior compared with MB staining for detecting SIM by comparison with the exact McNemar's test (P = 0.0391). The magnified observation of a short-segment BE according to the mucosal pattern and its classification can be predictive of SIM.

High School Gay-Straight Alliances (GSAs) and Young Adult Well-Being: An Examination of GSA Presence, Participation, and Perceived Effectiveness

ERIC Educational Resources Information Center

Toomey, Russell B.; Ryan, Caitlin; Diaz, Rafael M.; Russell, Stephen T.

2011-01-01

Gay-Straight Alliances (GSAs) are student-led, school-based clubs that aim to provide a safe environment in the school context for lesbian, gay, bisexual, and transgender (LGBT) students, as well as their straight allies. The present study examines the potential for GSAs to support positive youth development and to reduce associations among…

Gliding flight: drag and torque of a hawk and a falcon with straight and turned heads, and a lower value for the parasite drag coefficient.

PubMed

Tucker, V A

2000-12-01

Raptors - falcons, hawks and eagles in this study - such as peregrine falcons (Falco peregrinus) that attack distant prey from high-speed dives face a paradox. Anatomical and behavioral measurements show that raptors of many species must turn their heads approximately 40 degrees to one side to see the prey straight ahead with maximum visual acuity, yet turning the head would presumably slow their diving speed by increasing aerodynamic drag. This paper investigates the aerodynamic drag part of this paradox by measuring the drag and torque on wingless model bodies of a peregrine falcon and a red-tailed hawk (Buteo jamaicensis) with straight and turned heads in a wind tunnel at a speed of 11.7 m s(-)(1). With a turned head, drag increased more than 50 %, and torque developed that tended to yaw the model towards the direction in which the head pointed. Mathematical models for the drag required to prevent yawing showed that the total drag could plausibly more than double with head-turning. Thus, the presumption about increased drag in the paradox is correct. The relationships between drag, head angle and torque developed here are prerequisites to the explanation of how a raptor could avoid the paradox by holding its head straight and flying along a spiral path that keeps its line of sight for maximum acuity pointed sideways at the prey. Although the spiral path to the prey is longer than the straight path, the raptor's higher speed can theoretically compensate for the difference in distances; and wild peregrines do indeed approach prey by flying along curved paths that resemble spirals. In addition to providing data that explain the paradox, this paper reports the lowest drag coefficients yet measured for raptor bodies (0.11 for the peregrine and 0.12 for the red-tailed hawk) when the body models with straight heads were set to pitch and yaw angles for minimum drag. These values are markedly lower than value of the parasite drag coefficient (C(D,par)) of 0.18 previously

Persistence, period and precision of autonomous cellular oscillators from the zebrafish segmentation clock

PubMed Central

Webb, Alexis B; Lengyel, Iván M; Jörg, David J; Valentin, Guillaume; Jülicher, Frank; Morelli, Luis G; Oates, Andrew C

2016-01-01

In vertebrate development, the sequential and rhythmic segmentation of the body axis is regulated by a “segmentation clock”. This clock is comprised of a population of coordinated oscillating cells that together produce rhythmic gene expression patterns in the embryo. Whether individual cells autonomously maintain oscillations, or whether oscillations depend on signals from neighboring cells is unknown. Using a transgenic zebrafish reporter line for the cyclic transcription factor Her1, we recorded single tailbud cells in vitro. We demonstrate that individual cells can behave as autonomous cellular oscillators. We described the observed variability in cell behavior using a theory of generic oscillators with correlated noise. Single cells have longer periods and lower precision than the tissue, highlighting the role of collective processes in the segmentation clock. Our work reveals a population of cells from the zebrafish segmentation clock that behave as self-sustained, autonomous oscillators with distinctive noisy dynamics. DOI: http://dx.doi.org/10.7554/eLife.08438.001 PMID:26880542

NOTE: Reducing the number of segments in unidirectional MLC segmentations

NASA Astrophysics Data System (ADS)

Mellado, X.; Cruz, S.; Artacho, J. M.; Canellas, M.

2010-02-01

In intensity-modulated radiation therapy (IMRT), fluence matrices obtained from a treatment planning system are usually delivered by a linear accelerator equipped with a multileaf collimator (MLC). A segmentation method is needed for decomposing these fluence matrices into segments suitable for the MLC, and the number of segments used is an important factor for treatment time. In this work, an algorithm for reduction of the number of segments (NS) is presented for unidirectional segmentations, where there is no backtracking of the MLC leaves. It uses a geometrical representation of the segmentation output for searching the key values in a fluence matrix that complicate its decomposition. The NS reduction is achieved by performing minor modifications in these values, under the conditions of avoiding substantial modifications of the dose-volume histogram, and does not increase in average the total number of monitor units delivered. The proposed method was tested using two clinical cases planned with the PCRT 3D® treatment planning system.

Straight Ahead in Microgravity

NASA Technical Reports Server (NTRS)

Wood, S. J.; Vanya, R. D.; Clement, G.

2014-01-01

This joint ESA-NASA study will address adaptive changes in spatial orientation related to the subjective straight ahead, and the use of a vibrotactile sensory aid to reduce perceptual errors. The study will be conducted before and after long-duration expeditions to the International Space Station (ISS) to examine how spatial processing of target location is altered following exposure to microgravity. This project specifically addresses the sensorimotor research gap "What are the changes in sensorimotor function over the course of a mission?" Six ISS crewmembers will be requested to participate in three preflight sessions (between 120 and 60 days prior to launch) and then three postflight sessions on R+0/1 day, R+4 +/-2 days, and R+8 +/-2 days. The three specific aims include: (a) fixation of actual and imagined target locations at different distances; (b) directed eye and arm movements along different spatial reference frames; and (c) the vestibulo-ocular reflex during translation motion with fixation targets at different distances. These measures will be compared between upright and tilted conditions. Measures will then be compared with and without a vibrotactile sensory aid that indicates how far one has tilted relative to the straight-ahead direction. The flight study was been approved by the medical review boards and will be implemented in the upcoming Informed Crew Briefings to solicit flight subject participation. Preliminary data has been recorded on 6 subjects during parabolic flight to examine the spatial coding of eye movements during roll tilt relative to perceived orientations while free-floating during the microgravity phase of parabolic flight or during head tilt in normal gravity. Binocular videographic recordings obtained in darkness allowed us to quantify the mean deviations in gaze trajectories along both horizontal and vertical coordinates relative to the aircraft and head orientations. During some parabolas, a vibrotactile sensory aid provided

Segmental folding of chromosomes: A basis for structural and regulatory chromosomal neighborhoods?

PubMed Central

Nora, Elphège P; Dekker, Job; Heard, Edith

2013-01-01

We discuss here a series of testable hypotheses concerning the role of chromosome folding into topologically associating domains (TADs). Several lines of evidence suggest that segmental packaging of chromosomal neighborhoods may underlie features of chromatin that span large domains, such as heterochromatin blocks, association with the nuclear lamina and replication timing. By defining which DNA elements preferentially contact each other, the segmentation of chromosomes into TADs may also underlie many properties of long-range transcriptional regulation. Several observations suggest that TADs can indeed provide a structural basis to regulatory landscapes, by controlling enhancer sharing and allocation. We also discuss how TADs may shape the evolution of chromosomes, by causing maintenance of synteny over large chromosomal segments. Finally we suggest a series of experiments to challenge these ideas and provide concrete examples illustrating how they could be practically applied. PMID:23832846

Neutral-Line Magnetic Shear and Enhanced Coronal Heating in Solar Active Regions

NASA Technical Reports Server (NTRS)

Falconer, D. A.; Moore, R. L.; Porter, J. G.; Gary, G. A.; Shimizu, T.

1997-01-01

By examining the magnetic structure at sites in the bright coronal interiors of active regions that are not flaring but exhibit persistent strong coronal heating, we establish some new characteristics of the magnetic origins of this heating. We have examined the magnetic structure of these sites in five active regions, each of which was well observed by both the Yohkoh SXT and the Marshall Space Flight Center Vector Magnetograph and showed strong shear in its magnetic field along part of at least one neutral line (polarity inversion). Thus, we can assess whether this form of nonpotential field structure in active regions is a characteristic of the enhanced coronal heating and vice versa. From 27 orbits' worth of Yohkoh SXT images of the five active regions, we have obtained a sample of 94 persistently bright coronal features (bright in all images from a given orbit), 40 long (greater than or approximately equals 20,000 km) neutral-line segments having strong magnetic shear throughout (shear angle greater than 45 deg), and 39 long neutral-line segments having weak magnetic shear throughout (shear angle less than 45 deg). From this sample, we find that: (1) all of our persistently bright coronal features are rooted in magnetic fields that are stronger than 150 G; (2) nearly all (95%) of these enhanced coronal features are rooted near neutral lines (closer than 10,000 km); (3) a great majority (80%) of the bright features are rooted near strong-shear portions of neutral lines; (4) a great majority (85%) of long strong-shear segments of neutral lines have persistently bright coronal features rooted near them; (5) a large minority (40%) of long weak-shear segments of neutral lines have persistently bright coronal features rooted near them; and (6) the brightness of a persistently bright Coronal feature often changes greatly over a few hours. From these results, we conclude that most persistent enhanced heating of coronal loops in active regions: (1) requires the

Analysis and design of segment control system in segmented primary mirror

NASA Astrophysics Data System (ADS)

Yu, Wenhao; Li, Bin; Chen, Mo; Xian, Hao

2017-10-01

Segmented primary mirror will be adopted widely in giant telescopes in future, such as TMT, E-ELT and GMT. High-performance control technology of the segmented primary mirror is one of the difficult technologies for telescopes using segmented primary mirror. The control of each segment is the basis of control system in segmented mirror. Correcting the tilt and tip of single segment is the main work of this paper which is divided into two parts. Firstly, harmonic response done in finite element model of single segment matches the Bode diagram of a two-order system whose natural frequency is 45 hertz and damping ratio is 0.005. Secondly, a control system model is established, and speed feedback is introduced in control loop to suppress resonance point gain and increase the open-loop bandwidth, up to 30Hz or even higher. Corresponding controller is designed based on the control system model described above.