Performance Analysis of Retrofitted Tribo-Corrosion Test Rig for Monitoring In Situ Oil Conditions

PubMed Central

Ramachandran, Rahul; Menezes, Pradeep L.

2017-01-01

Oils and lubricants, once extracted after use from a mechanical system, can hardly be reused, and should be refurbished or replaced in most applications. New methods of in situ oil and lubricant efficiency monitoring systems have been introduced for a wide variety of mechanical systems, such as automobiles, aerospace aircrafts, ships, offshore wind turbines, and deep sea oil drilling rigs. These methods utilize electronic sensors to monitor the “byproduct effects” in a mechanical system that are not indicative of the actual remaining lifecycle and reliability of the oils. A reliable oil monitoring system should be able to monitor the wear rate and the corrosion rate of the tribo-pairs due to the inclusion of contaminants. The current study addresses this technological gap, and presents a novel design of a tribo-corrosion test rig for oils used in a dynamic system. A pin-on-disk tribometer test rig retrofitted with a three electrode-potentiostat corrosion monitoring system was used to analyze the corrosion and wear rate of a steel tribo-pair in industrial grade transmission oil. The effectiveness of the retrofitted test rig was analyzed by introducing various concentrations of contaminants in an oil medium that usually leads to a corrosive working environment. The results indicate that the retrofitted test rig can effectively monitor the in situ tribological performance of the oil in a controlled dynamic corrosive environment. It is a useful method to understand the wear–corrosion synergies for further experimental work, and to develop accurate predictive lifecycle assessment and prognostic models. The application of this system is expected to have economic benefits and help reduce the ecological oil waste footprint. PMID:28956819

Effect of microstructure of nano- and micro-particle filled polymer composites on their tribo-mechanical performance

NASA Astrophysics Data System (ADS)

Devaprakasam, D.; Hatton, P. V.; Möbus, G.; Inkson, B. J.

2008-08-01

In this work we have investigated the influence of nanoscale and microscale structure on the tribo-mechanical performance and failure mechanisms of two biocompatible dental polymer composites, with different reinforcing particulates, using advanced microscopy techniques. Nano- and micro structural analysis reveals the shape, size and distribution of the particles in the composites. In the microparticle filled polymer composite (microcomposite), the particles are of irregular shape with sharp edges with non-uniform distribution in the matrix. However, in the nanoparticle filled composites (nanocomposite), filler particles are spherical in shape with uniform distribution in the matrix. From nanoindentation measurements, hardness and reduced modulus of the microcomposite were found to be heterogeneous. However, the hardness and reduced modulus of the nanocomposite were found to be homogeneous. The nanocomposite shows better tribo-mechanical performance compared to that of the microcomposite.

Tailoring vibration mode shapes using topology optimization and functionally graded material concepts

NASA Astrophysics Data System (ADS)

Montealegre Rubio, Wilfredo; Paulino, Glaucio H.; Nelli Silva, Emilio Carlos

2011-02-01

Tailoring specified vibration modes is a requirement for designing piezoelectric devices aimed at dynamic-type applications. A technique for designing the shape of specified vibration modes is the topology optimization method (TOM) which finds an optimum material distribution inside a design domain to obtain a structure that vibrates according to specified eigenfrequencies and eigenmodes. Nevertheless, when the TOM is applied to dynamic problems, the well-known grayscale or intermediate material problem arises which can invalidate the post-processing of the optimal result. Thus, a more natural way for solving dynamic problems using TOM is to allow intermediate material values. This idea leads to the functionally graded material (FGM) concept. In fact, FGMs are materials whose properties and microstructure continuously change along a specific direction. Therefore, in this paper, an approach is presented for tailoring user-defined vibration modes, by applying the TOM and FGM concepts to design functionally graded piezoelectric transducers (FGPT) and non-piezoelectric structures (functionally graded structures—FGS) in order to achieve maximum and/or minimum vibration amplitudes at certain points of the structure, by simultaneously finding the topology and material gradation function. The optimization problem is solved by using sequential linear programming. Two-dimensional results are presented to illustrate the method.

Material system for tailorable white light emission and method for making thereof

DOEpatents

Smith, Christine A.; Lee, Howard W.

2004-08-10

A method of processing a composite material to tailor white light emission of the resulting composite during excitation. The composite material is irradiated with a predetermined power and for a predetermined time period to reduce the size of a plurality of nanocrystals and the number of a plurality of traps in the composite material. By this irradiation process, blue light contribution from the nanocrystals to the white light emission is intensified and red and green light contributions from the traps are decreased.

Material system for tailorable white light emission and method for making thereof

DOEpatents

Smith, Christine A [Livermore, CA; Lee, Howard W. H. [Fremont, CA

2009-05-19

A method of processing a composite material to tailor white light emission of the resulting composite during excitation. The composite material is irradiated with a predetermined power and for a predetermined time period to reduce the size of a plurality of nanocrystals and the number of a plurality of traps in the composite material. By this irradiation process, blue light contribution from the nanocrystals to the white light emission is intensified and red and green light contributions from the traps are decreased.

Synthesized multi-station tribo-test system for bio-tribological evaluation in vitro

NASA Astrophysics Data System (ADS)

Wu, Tonghai; Du, Ying; Li, Yang; Wang, Shuo; Zhang, Zhinan

2016-07-01

Tribological tests play an important role on the evaluation of long-term bio-tribological performances of prosthetic materials for commercial fabrication. Those tests focus on the motion simulation of a real joint in vitro with only normal loads and constant velocities, which are far from the real friction behavior of human joints characterized with variable loads and multiple directions. In order to accurately obtain the bio-tribological performances of artificial joint materials, a tribological tester with a miniature four-station tribological system is proposed with four distinctive features. Firstly, comparability and repeatability of a test are ensured by four equal stations of the tester. Secondly, cross-linked scratch between tribo-pairs of human joints can be simulated by using a gear-rack meshing mechanism to produce composite motions. With this mechanism, the friction tracks can be designed by varying reciprocating and rotating speeds. Thirdly, variable loading system is realized by using a ball-screw mechanism driven by a stepper motor, by which loads under different gaits during walking are simulated. Fourthly, dynamic friction force and normal load can be measured simultaneously. The verifications of the performances of the developed tester show that the variable frictional tracks can produce different wear debris compared with one-directional tracks, and the accuracy of loading and friction force is within ±5%. Thus the high consistency among different stations can be obtained. Practically, the proposed tester system could provide more comprehensive and accurate bio-tribological evaluations for prosthetic materials.

Innovative materials tailored for advanced micro-optic applications

NASA Astrophysics Data System (ADS)

Himmelhuber, Roland; Fink, Marion; Pfeiffer, Karl; Ostrzinski, Ute; Klukowska, Anna; Gruetzner, Gabi; Houbertz, Ruth; Wolter, Herbert

2007-02-01

The handling of a continuously increasing amount of data leads to a strong need for high-speed short-range connections. Conventional Cu technology between chips on a board is limited. Optical interconnects will dominate the market, since they can overcome the limitations. One of the issues for materials used, e.g., for waveguides embedded in printed circuit boards (PCBs) is the compatibility with standard epoxies used for PCBs during the entire board fabrication process. Materials applied for optical interconnects should be mechanically and optically reliable, and also allow low-cost production. From the material production side, the process should be easy to up-scale. Therefore, anticipatory research strategy and suitable tailoring is asked for. The handling of light in the UV and visible range often requires the use of specially designed materials. Most polymer materials show an increased yellowing effect upon being exposed to shorter wavelength light. The major influence on the absorption in the UV and visible range of a UV curable material is related to the UV initiator, beside any other chromophores formed mainly during the exposure. Different material approaches will be presented which fulfil the requirements for highly sophisticated applications in optics / optical packaging technology. Firstly, an epoxy-based material system for optical chip-to-chip interconnection will be introduced. Secondly, the adaptation of a UV patternable inorganic-organic hybrid material (ORMOCER ®) originally developed for waveguide applications in the data and telecom regime, will be discussed with respect to applications in the visible regime. Spectroscopy and UV-DSC measurements were carried out to investigate the influence of standard photoinitiators on the optical properties for an ORMOCER ® system suitable for microoptic applications. The results show that the resulting material properties were significantly improved by exchange of the initiators compared to the originally

Tailor-welded blanks and their production

NASA Astrophysics Data System (ADS)

Yan, Qi

2005-01-01

Tailor welded blanks had been widely used in the automobile industry. A tailor welded blank consists of several flat sheets that were laser welded together before stamping. A combination of different materials, thickness, and coatings could be welded together to form a blank for stamping car body panels. As for the material for automobile industry, this technology was one of the development trend for automobile industry because of its weight reduction, safety improvement and economical use of materials. In this paper, the characters and production of tailor welded blanks in the market were discussed in detail. There had two major methods to produce tailor welded blanks. Laser welding would replace mesh seam welding for the production of tailor welded blanks in the future. The requirements on the edge preparation of unwelded blanks for tailor welded blanks were higher than the other steel processing technology. In order to produce the laser welded blank, there had the other process before the laser welding in the factory. In the world, there had three kinds of patterns for the large volume production of tailor welded blanks. In China, steel factory played the important role in the promotion of the application of tailor welded blanks. The competition for the supply of tailor welded blanks to the automobile industry would become fierce in the near future. As a result, the demand for the quality control on the production of tailor welded blanks would be the first priority concern for the factory.

Functionally Graded Designer Viscoelastic Materials Tailored to Perform Prescribed Tasks with Probabilistic Failures and Lifetimes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hilton, Harry H.

Protocols are developed for formulating optimal viscoelastic designer functionally graded materials tailored to best respond to prescribed loading and boundary conditions. In essence, an inverse approach is adopted where material properties instead of structures per se are designed and then distributed throughout structural elements. The final measure of viscoelastic material efficacy is expressed in terms of failure probabilities vs. survival time000.

Multidisciplinary tailoring of hot composite structures

NASA Technical Reports Server (NTRS)

Singhal, Surendra N.; Chamis, Christos C.

1993-01-01

A computational simulation procedure is described for multidisciplinary analysis and tailoring of layered multi-material hot composite engine structural components subjected to simultaneous multiple discipline-specific thermal, structural, vibration, and acoustic loads. The effect of aggressive environments is also simulated. The simulation is based on a three-dimensional finite element analysis technique in conjunction with structural mechanics codes, thermal/acoustic analysis methods, and tailoring procedures. The integrated multidisciplinary simulation procedure is general-purpose including the coupled effects of nonlinearities in structure geometry, material, loading, and environmental complexities. The composite material behavior is assessed at all composite scales, i.e., laminate/ply/constituents (fiber/matrix), via a nonlinear material characterization hygro-thermo-mechanical model. Sample tailoring cases exhibiting nonlinear material/loading/environmental behavior of aircraft engine fan blades, are presented. The various multidisciplinary loads lead to different tailored designs, even those competing with each other, as in the case of minimum material cost versus minimum structure weight and in the case of minimum vibration frequency versus minimum acoustic noise.

Spectral tailoring device

DOEpatents

Brager, H.R.; Schenter, R.E.; Carter, L.L.; Karnesky, R.A.

1987-08-05

A spectral tailoring device for altering the neutron energy spectra and flux of neutrons in a fast reactor thereby selectively to enhance or inhibit the transmutation rate of a target metrical to form a product isotope. Neutron moderators, neutron filters, neutron absorbers and neutron reflectors may be used as spectral tailoring devices. Depending on the intended use for the device, a member from each of these four classes of materials could be used singularly, or in combination, to provide a preferred neutron energy spectra and flux of the neutrons in the region of the target material. In one embodiment of the invention, an assembly is provided for enhancing the production of isotopes, such as cobalt 60 and gadolinium 153. In another embodiment of the invention, a spectral tailoring device is disposed adjacent a target material which comprises long lived or volatile fission products and the device is used to shift the neutron energy spectra and flux of neutrons in the region of the fission products to preferentially transmute them to produce a less volatile fission product inventory. 6 figs.

Exploratory Experiments in the Tribological Behavior of Engineering Surfaces with Nano-Coating Using a Tribo-Rheometer

DTIC Science & Technology

2008-05-30

Tribological behavior and graphitization of carbon nanotubes grown on 440C stainless steel . Tribo. Lett., 19(2):119-125, 2005. D-2 ...with a stainless steel parallel plate configuration as shown in figure 1. Due to the radial variation of the local shear stress T in the parallel...using a force transducer that is mounted below the surface. B-1 Exploded View Stainless Steel Plate Lower Fixture Microscale View Figure 1:

Diallyl disulphide as natural organosulphur friction modifier via the in-situ tribo-chemical formation of tungsten disulphide

NASA Astrophysics Data System (ADS)

Rodríguez Ripoll, Manel; Totolin, Vladimir; Gabler, Christoph; Bernardi, Johannes; Minami, Ichiro

2018-01-01

The present work shows a novel method for generating in-situ low friction tribofilms containing tungsten disulphide in lubricated contacts using diallyl disulphide as sulphur precursor. The approach relies on the tribo-chemical interaction between the diallyl disulphide and a surface containing embedded sub-micrometer tungsten carbide particles. The results show that upon sliding contact between diallyl disulphide and the tungsten-containing surface, the coefficient of friction drops to values below 0.05 after an induction period. The reason for the reduction in friction is due to tribo-chemical reactions that leads to the in-situ formation of a complex tribofilm that contains iron and tungsten components. X-ray photoelectron spectroscopy analyses indicate the presence of tungsten disulphide at the contact interface, thus justifying the low coefficient of friction achieved during the sliding experiments. It was proven that the low friction tribofilms can only be formed by the coexistence of tungsten and sulphur species, thus highlighting the synergy between diallyl disulphide and the tungsten-containing surface. The concept of functionalizing surfaces to react with specific additives opens up a wide range of possibilities, which allows tuning on-site surfaces to target additive interactions.

Computer-generated tailored feedback letters for smoking cessation: theoretical and empirical variability of tailoring.

PubMed

Schumann, Anja; John, Ulrich; Ulbricht, Sabina; Rüge, Jeannette; Bischof, Gallus; Meyer, Christian

2008-11-01

This study examines tailored feedback letters of a smoking cessation intervention that is conceptually based on the transtheoretical model, from a content-based perspective. Data of 2 population-based intervention studies, both randomized controlled trials, with total N=1044 were used. The procedure of the intervention, the tailoring principle for the feedback letters, and the content of the intervention materials are described in detail. Theoretical and empirical frequencies of unique feedback letters are presented. The intervention system was able to generate a total of 1040 unique letters with normative feedback only, and almost half a million unique letters with normative and ipsative feedback. Almost every single smoker in contemplation, preparation, action, and maintenance had an empirically unique combination of tailoring variables and received a unique letter. In contrast, many smokers in precontemplation shared a combination of tailoring variables and received identical letters. The transtheoretical model provides an enormous theoretical and empirical variability of tailoring. However, tailoring for a major subgroup of smokers, i.e. those who do not intend to quit, needs improvement. Conceptual ideas for additional tailoring variables are discussed.

Recent Observations on the Performance of Hybrid Ceramic Tribo-Contacts

NASA Astrophysics Data System (ADS)

Buttery, M.; Cropper, M.; Wardzinski, B.; Lewis, S.; McLaren, S.; Kreuser, J.

2015-09-01

Hybrid ceramic ball bearings offer great promise in space applications but have not been rapidly adopted by industry perhaps partly due to the relatively low amount of published data on specific in-vacuum performance. Such bearings, having, typically, silicon nitride balls and 440C or high nitrogen steel (e.g. X30) raceways offer the potential for long life and low torque noise due a combination of chemical inertness, high hardness and the extremely smooth surfaces produced in ceramic balls. Though initial benefits were foreseen for high speed applications, the potential for reduced adhesive forces and wear in conditions of marginal lubrication, and for improvements in lubricant lifetime in long life applications limited by oil tribo-degradation render hybrid ceramic bearings more generally attractive.This paper draws together a number of experimental studies carried out at Pin-on-Disc (POD), Spiral Orbit Tribometer (SOT) and bearing-level recently at ESTL.

The vacuum tribology model (VTM) of TriboLAB

NASA Astrophysics Data System (ADS)

Garmendia, I.; Landaberea, A.; Anglada, E.; Fernández-Sanz, R.; Santiago, R.; Herrada, F.; Encinas, J. M.

2003-09-01

TriboLAB is a tribology instrument that is planned for installation in the EuteF Flight Segment Platform, along with several other European scientific instruments. EuteF will be fixed onto an Express Pallet Adapter (ExPA), which provides standard structural, mechanical, electrical and communications interfaces to the Columbus External Payload Facility of the International Space Station (ISS). As a part of the model philosophy, a vacuum tribological model (VTM) has been developed to generate "on ground" tribological data of selected lubricants. The idea is to compare the results obtained "on ground" with those that will be produced in the space, in order to investigate the different behaviors of same tribological films and to be able to compare the performance of specific lubricants in Low Earth Orbit (LEO) conditions. The VTM is composed of six double experiment cells that perform respectively ball bearing (BB) experiments (with liquid and solid lubrication) and pin-on-disk (PoD) tests of solid lubricants. Thin films of alloyed MoS2 are being tested in the VTM under controlled vacuum conditions. In this work, the two sections of the VTM are described.

Processing and properties of Titanium alloy based materials with tailored porosity and composition

NASA Astrophysics Data System (ADS)

Cabezas-Villa, Jose Luis; Olmos, Luis; Lemus-Ruiz, Jose; Bouvard, Didier; Chavez, Jorge; Jimenez, Omar; Manuel Solorio, Victor

2017-06-01

This paper deals with powder processing of Ti6Al4V titanium alloy based materials with tailored porosity and composition. Ti6Al4V powder was mixed either with salt particles acting as space holder, so as to provide two-scale porosity, or with hard TiN particles that significantly modified the microstructure of the material and increased its hardness. Finally an original three-layer component was produced. Sample microstructure was observed by SEM and micro-tomography with special interest in pore size and shape, inclusion distribution and connectivity. Compression tests provided elastic modulus and yield stress as functions of density. These materials are representative of bone implants subjected to complex biological and mechanical conditions. These results thus open avenues for processing personalized implants by powder metallurgy.

Tailoring the structures and photonic properties of low-dimensional organic materials by crystal engineering.

PubMed

Li, Qing; Jin, Wang; Chu, Manman; Zhang, Wei; Gu, Jianmin; Shahid, Bilal; Chen, Aibing; Yu, Yifeng; Qiao, Shanlin; Zhao, Yong Sheng

2018-03-08

Low-dimensional organic materials have given rise to tremendous interest in optoelectronic applications, owing to their controllable photonic properties. However, the controlled-synthesis approaches for organic nano-/micro-architectures are very difficult to attain, because the weak interaction (van der Waals force) between the organic molecules cannot dominate the kinetic process of crystal growth. We report a simple method, which involves selective adhesion to the organic crystal plane by hydrogen-bonding interaction for modulating the crystal growth process, which leads either to the self-assembly of one organic molecule into two-dimensional (2D) microsheets with an obvious asymmetric light propagation or one-dimensional (1D) microrods with low propagation loss. The method of tailoring the structures and photonic properties for fabricating different micro-structures would provide enlightenment for the development of tailor-made mini-sized devices for photonic integrated circuits.

A controlled release of ibuprofen by systematically tailoring the morphology of mesoporous silica materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qu Fengyu; Chemistry and Pharmaceutical College, Jiamusi University, Jiamusi 154007; Zhu Guangshan

2006-07-15

A series of mesoporous silica materials with similar pore sizes, different morphologies and variable pore geometries were prepared systematically. In order to control drug release, ibuprofen was employed as a model drug and the influence of morphology and pore geometry of mesoporous silica on drug release profiles was extensively studied. The mesoporous silica and drug-loaded samples were characterized by X-ray diffraction, Fourier transform IR spectroscopy, N{sub 2} adsorption and desorption, scanning electron microscopy, and transmission electron microscopy. It was found that the drug-loading amount was directly correlated to the Brunauer-Emmett-Teller surface area, pore geometry, and pore volume; while the drugmore » release profiles could be controlled by tailoring the morphologies of mesoporous silica carriers. - Graphical abstract: The release of ibuprofen is controlled by tailoring the morphologies of mesoporous silica. The mesoporous silica and drug-loaded samples are characterized by powder X-ray diffraction, Fourier transform IR spectroscopy, N{sub 2} adsorption and desorption, scanning electron microscopy, and transmission electron microscopy. The drug-loading amount is directly correlated to the Brunauer-Emmett-Teller surface area, pore geometry, and pore volume; while the drug release profiles can be controlled by tailoring the morphologies of mesoporous silica carriers.« less

Evaluating Psychosocial and Behavioral Mechanisms of Change in a Tailored Communication Intervention

ERIC Educational Resources Information Center

Elder, John P.; Ayala, Guadalupe X.; Slymen, Donald J.; Arredondo, Elva M.; Campbell, Nadia R.

2009-01-01

This study examined the impact of a tailored nutrition intervention at 3 and 6 months postintervention. In all, 357 Latinas were randomly assigned to one of three conditions: (1) a control condition comprised of previously developed Spanish language targeted materials, (2) tailored print materials, or (3) tailored print materials accompanied by…

Supercapacitor Electrode Materials from Highly Porous Carbon Nanofibers with Tailored Pore Distributions

NASA Astrophysics Data System (ADS)

Chathurika Abeykoon, Nimali

Environmental and human health risks associated with the traditional methods of energy production (e.g., oil and gas) and intermittency and uncertainty of renewable sources (e.g., solar and wind) have led to exploring effective and alternative energy sources to meet the growing energy demands. Electricity based on energy storage devices are the most promising solutions for realization of these objectives. Among the energy storage devices, electrochemical double layer capacitors (EDLCs) or supercapacitors have become an attractive research interest due to their outstanding performance, especially high power densities, long cycle life and rapid charge and discharge times, which enables them to utilize in many applications including consumer electronics and transportation, where high power is needed. However, low energy density of supercapacitors is a major obstacle to compete with the commercially existing high energy density energy storage device such as batteries. The fabrication of advanced electrodes materials with very high surface area from novel precursors and utilization of electrolytes with higher operating voltages are essential to enhance energy density of supercapacitors. In this work, carbon nanofibers (CNFs) from different polymer precursors with new fabrication techniques are explored to develop highly porous carbon with tailored pore distributions to match with employed ionic liquid electrolytes (which possess high working voltages), to realize high energy storage capability. Novel electrode materials derived from electrospun immiscible polymer blends and synthesized copolymers and terpolymers were described. Pore distributions of CNFs were tailored by varying the composition of polymers in immiscible blends or varying the monomer ratios of copolymer or terpolymers. Chapter 1 gives the detailed introduction of supercapacitors including history and storage principle of EDLCs, fabrication of carbon nanofiber based electrodes and electrolytes employed

ZERODUR TAILORED for cryogenic application

NASA Astrophysics Data System (ADS)

Jedamzik, R.; Westerhoff, T.

2014-07-01

ZERODUR® glass ceramic from SCHOTT is known for its very low thermal expansion coefficient (CTE) at room temperature and its excellent CTE homogeneity. It is widely used for ground-based astronomical mirrors but also for satellite applications. Many reference application demonstrate the excellent and long lasting performance of ZERODUR® components in orbit. For space application a low CTE of the mirror material is required at cryogenic temperatures together with a good match of the thermal expansion to the supporting structure material. It is possible to optimize the coefficient of thermal expansion of ZERODUR® for cryogenic applications. This paper reports on measurements of thermal expansion of ZERODUR® down to cryogenic temperatures of 10 K performed by the PTB (Physikalisch Technische Bundesanstallt, Braunschweig, Germany, the national metrology laboratory). The ZERODUR® TAILORED CRYO presented in this paper has a very low coefficient of thermal expansion down to 70 K. The maximum absolute integrated thermal expansion down to 10 K is only about 20 ppm. Mirror blanks made from ZERODUR® TAILORED CRYO can be light weighted to almost 90% with our modern processing technologies. With ZERODUR® TAILORED CRYO, SCHOTT offers the mirror blank material for the next generation of space telescope applications.

Functional Polymer Opals and Porous Materials by Shear-Induced Assembly of Tailor-Made Particles.

PubMed

Gallei, Markus

2018-02-01

Photonic band-gap materials attract enormous attention as potential candidates for a steadily increasing variety of applications. Based on the preparation of easily scalable monodisperse colloids, such optically attractive photonic materials can be prepared by an inexpensive and convenient bottom-up process. Artificial polymer opals can be prepared by shear-induced assembly of core/shell particles, yielding reversibly stretch-tunable materials with intriguing structural colors. This feature article highlights recent developments of core/shell particle design and shear-induced opal formation with focus on the combination of hard and soft materials as well as crosslinking strategies. Structure formation of opal materials relies on both the tailored core/shell architecture and the parameters for polymer processing. The emphasis of this feature article is on elucidating the particle design and incorporation of addressable moieties, i.e., stimuli-responsive polymers as well as elaborated crosslinking strategies for the preparation of smart (inverse) opal films, inorganic/organic opals, and ceramic precursors by shear-induced ordering. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A Mechanical, Microstructural, and Damage Study of Various Tailor Hot Stamped Material Conditions Consisting of Martensite, Bainite, Ferrite, and Pearlite

NASA Astrophysics Data System (ADS)

Bardelcik, Alexander; Vowles, Caryn J.; Worswick, Michael J.

2018-04-01

This paper examines the mechanical, microstructural, and damage characteristics of five different material conditions that were created using the tailored hot stamping process with in-die heating. The tailored material conditions, TMC1 to TMC5 (softest-hardest), were created using die temperatures ranging from 700 °C to 400 °C, respectively. The tensile strength (and total elongation) ranged from 615 MPa (0.24) for TMC1 to 1122 MPa (0.11) for TMC5. TMC3 and TMC4 exhibited intermediate strength levels, with almost no increase in total elongation relative to TMC5. FE-SEM microscopy was used to quantify the mixed-phase microstructures, which ranged in volume fractions of ferrite, pearlite, bainite, and martensite. High-resolution optical microscopy was used to quantify void accumulation and showed that the total void area fraction at 0.60 thickness strain was low for TMC1 and TMC5 ( 0.09 pct) and highest for TMC3 (0.31 pct). Damage modes were characterized and revealed that the poor damage behavior of TMC3 (martensite/bainite/ferrite composition) was a result of small martensitic grains forming at grain boundaries and grain boundary junctions, which facilitated void nucleation as shown by the highest measured void density for this particular material condition. The excellent ductility of TMC1 was a result of a large grained ferritic/pearlitic microstructure that was less susceptible to void nucleation and growth. Large titanium nitride (TiN) inclusions were observed in all of the tailored material conditions and it was shown that they noticeably contributed to the total void accumulation, specifically for the TMC3 and TMC4 material conditions.

Lay Health Influencers: How They Tailor Brief Tobacco Cessation Interventions

ERIC Educational Resources Information Center

Yuan, Nicole P.; Castaneda, Heide; Nichter, Mark; Nichter, Mimi; Wind, Steven; Carruth, Lauren; Muramoto, Myra

2012-01-01

Interventions tailored to individual smoker characteristics have increasingly received attention in the tobacco control literature. The majority of tailored interventions are generated by computers and administered with printed materials or web-based programs. The purpose of this study was to examine the tailoring activities of community lay…

Friction Regimes of Water-Lubricated Diamond (111): Role of Interfacial Ether Groups and Tribo-Induced Aromatic Surface Reconstructions

NASA Astrophysics Data System (ADS)

Kuwahara, Takuya; Moras, Gianpietro; Moseler, Michael

2017-09-01

Large-scale quantum molecular dynamics of water-lubricated diamond (111) surfaces in sliding contact reveals multiple friction regimes. While water starvation causes amorphization of the tribological interface, small H2O traces are sufficient to preserve crystallinity. This can result in high friction due to cold welding via ether groups or in ultralow friction due to aromatic surface passivation triggered by tribo-induced Pandey reconstruction. At higher water coverage, Grotthuss-type diffusion and H2O dissociation yield dense H /OH surface passivation leading to another ultralow friction regime.

Can tailored interventions increase mammography use among HMO women?

PubMed

Lipkus, I M; Rimer, B K; Halabi, S; Strigo, T S

2000-01-01

Telephone counseling and tailored print communications have emerged as promising methods for promoting mammography screening. However, there has been little research testing, within the same randomized field trial, of the efficacy of these two methods compared to a high-quality usual care system for enhancing screening. This study addressed the question: Compared to usual care, is tailored telephone counseling more effective than tailored print materials for promoting mammography screening? Three-year randomized field trial. One thousand ninety-nine women aged 50 and older recruited from a health maintenance organization in North Carolina. Women were randomized to 1 of 3 groups: (1) usual care, (2) tailored print communications, and (3) tailored telephone counseling. Adherence to mammography screening based on self-reports obtained during 1995, 1996, and 1997. Compared to usual care alone, telephone counseling promoted a significantly higher proportion of women having mammograms on schedule (71% vs 61%) than did tailored print (67% vs 61%) but only after the first year of intervention (during 1996). Furthermore, compared to usual care, telephone counseling was more effective than tailored print materials at promoting being on schedule with screening during 1996 and 1997 among women who were off-schedule during the previous year. The effects of the intervention were most pronounced after the first intervention. Compared to usual care, telephone counseling seemed particularly effective at promoting change among nonadherent women, the group for whom the intervention was developed. These results suggest that telephone counseling, rather than tailored print, might be the preferred first-line intervention for getting nonadherent women on schedule for mammography screening. Many questions would have to be answered about why the tailored print intervention was not more powerful. Nevertheless, it is clear that additional interventions will be needed to maintain women

Evaluating psychosocial and behavioral mechanisms of change in a tailored communication intervention.

PubMed

Elder, John P; Ayala, Guadalupe X; Slymen, Donald J; Arredondo, Elva M; Campbell, Nadia R

2009-04-01

This study examined the impact of a tailored nutrition intervention at 3 and 6 months postintervention. In all, 357 Latinas were randomly assigned to one of three conditions: (1) a control condition comprised of previously developed Spanish language targeted materials, (2) tailored print materials, or (3) tailored print materials accompanied by personalized dietary counseling via lay heath advisors (promotoras). At 6 months postintervention, significant group by time interactions were observed on the dietary behavioral strategies scales. The promotora condition resulted in significant behavior change initially; however, receipt of tailored and control materials was instrumental in continued behavior change after intervention activities had ceased. Group main effects suggested that the promotora condition was superior at reducing barriers and improving family interactions supporting healthy behaviors. The promotora model is an effective method for changing important dietary behaviors and psychosocial determinants, but longer term behavior change is achievable with less expensive intervention methods.

Aeroelastic Tailoring of Transport Aircraft Wings: State-of-the-Art and Potential Enabling Technologies

NASA Technical Reports Server (NTRS)

Jutte, Christine; Stanford, Bret K.

2014-01-01

This paper provides a brief overview of the state-of-the-art for aeroelastic tailoring of subsonic transport aircraft and offers additional resources on related research efforts. Emphasis is placed on aircraft having straight or aft swept wings. The literature covers computational synthesis tools developed for aeroelastic tailoring and numerous design studies focused on discovering new methods for passive aeroelastic control. Several new structural and material technologies are presented as potential enablers of aeroelastic tailoring, including selectively reinforced materials, functionally graded materials, fiber tow steered composite laminates, and various nonconventional structural designs. In addition, smart materials and structures whose properties or configurations change in response to external stimuli are presented as potential active approaches to aeroelastic tailoring.

Structural tailoring of engine blades (STAEBL)

NASA Technical Reports Server (NTRS)

Platt, C. E.; Pratt, T. K.; Brown, K. W.

1982-01-01

A mathematical optimization procedure was developed for the structural tailoring of engine blades and was used to structurally tailor two engine fan blades constructed of composite materials without midspan shrouds. The first was a solid blade made from superhybrid composites, and the second was a hollow blade with metal matrix composite inlays. Three major computerized functions were needed to complete the procedure: approximate analysis with the established input variables, optimization of an objective function, and refined analysis for design verification.

Aeroelastic Tailoring of the NASA Common Research Model via Novel Material and Structural Configurations

NASA Technical Reports Server (NTRS)

Jutte, Christine V.; Stanford, Bret K.; Wieseman, Carol D.; Moore, James B.

2014-01-01

This work explores the use of tow steered composite laminates, functionally graded metals (FGM), thickness distributions, and curvilinear rib/spar/stringer topologies for aeroelastic tailoring. Parameterized models of the Common Research Model (CRM) wing box have been developed for passive aeroelastic tailoring trade studies. Metrics of interest include the wing weight, the onset of dynamic flutter, and the static aeroelastic stresses. Compared to a baseline structure, the lowest aggregate static wing stresses could be obtained with tow steered skins (47% improvement), and many of these designs could reduce weight as well (up to 14%). For these structures, the trade-off between flutter speed and weight is generally strong, although one case showed both a 100% flutter improvement and a 3.5% weight reduction. Material grading showed no benefit in the skins, but moderate flutter speed improvements (with no weight or stress increase) could be obtained by grading the spars (4.8%) or ribs (3.2%), where the best flutter results were obtained by grading both thickness and material. For the topology work, large weight reductions were obtained by removing an inner spar, and performance was maintained by shifting stringers forward and/or using curvilinear ribs: 5.6% weight reduction, a 13.9% improvement in flutter speed, but a 3.0% increase in stress levels. Flutter resistance was also maintained using straightrotated ribs although the design had a 4.2% lower flutter speed than the curved ribs of similar weight and stress levels were higher. These results will guide the development of a future design optimization scheme established to exploit and combine the individual attributes of these technologies.

Tribological Behaviour of Ti:Ta-DLC Films Under Different Tribo-Test Conditions

NASA Astrophysics Data System (ADS)

Efeoglu, İhsan; Keleş, Ayşenur; Totik, Yaşar; Çiçek, Hikmet; Emine Süküroglu, Ebru

2018-01-01

Diamond-like carbon (DLC) films are suitable applicants for cutting tools due to their high hardness, low friction coefficient and wear rate. Doping metals in DLC films have been improved its tribological properties. In this study, titanium and tantalum doped hydrogenated DLC films were deposited by closed-field unbalanced magnetron sputtering system onto M2 high speed steels in Ar/N2/C2H2 atmosphere. The friction and wear properties of Ti:Ta-DLC film were investigated under different tribo-test conditions including in atmospheric pressure, distilled water, commercial oil and Ar atmosphere. The coated specimens were characterized by SEM and X-ray diffraction techniques. The bonding state of C-C (sp3) and C=C (sp2) were obtained with XPS. The tribological properties of Ti:Ta-DLC were investigated with pin-on-disc wear test. Hardness measurements performed by micro-indentation. Our results suggest that Ti:Ta-doped DLC film shows very dense columnar microstructure, high hardness (38.2 GPa) with low CoF (µ≈0.02) and high wear resistance (0.5E-6 mm3/Nm).

The efficacy of tailored print materials in promoting colorectal cancer screening: results from a randomized trial involving callers to the National Cancer Institute's Cancer Information Service.

PubMed

Marcus, Alfred C; Mason, Mondi; Wolfe, Pam; Rimer, Barbara K; Lipkus, Isaac; Strecher, Victor; Warneke, Richard; Morra, Marion E; Allen, Amy Reasinger; Davis, Sharon W; Gaier, Amy; Graves, Carlan; Julesberg, Karen; Nguyen, Lynne; Perocchia, Rosemarie; Speyer, Jo Beth; Wagner, Doug; Thomsen, Chris; Bright, Mary Anne

2005-01-01

In this large randomized trial among callers to the Cancer Information Service (CIS), tailored print materials were tested for efficacy in promoting colorectal cancer (CRC) screening (fecal occult blood test [FOBT], flexible sigmoidoscopy, or colonoscopy). All participants completed baseline interviews at the end of their usual service calls to the CIS, as well as short-term (6-month) and longer-term (14-month) telephone follow-up interviews. The study sample (n = 4,014) was restricted to English-speaking CIS callers 50 + years of age, who would be eligible for CRC screening at 14 months follow-up and did not call the CIS about CRC or CRC screening. Four experimental conditions were compared: a single untailored (SU) mailout of print material (the control condition); a single tailored (ST) mailout of print material; four (multiple) tailored (MT) mailouts of print materials spanning 12 months, all of which were tailored to information obtained at baseline; and four (multiple) retailored (MRT) mailouts also spanning 12 months, with retailoring of the print materials (mailouts 2, 3, and 4) based on updated information obtained from the 6-month follow-up interviews. Consistent with the main hypothesis of this trial, a significant linear trend across the SU, ST, MT, and MRT groups was found at 14 months (42%, 44%, 51%, and 48%, respectively, p = 0.05). Only for MT was there a significant difference compared with SU (p = 0.03) for the sample as a whole, while no differences were found for MT vs. MRT at 14 months. Significant moderator effects in the predicted direction were found among females, younger participants, and among those with a history of CRC screening, all of which involved the SU vs. MT MRT comparisons. Only among younger participants (ages 50-59) was there a difference between SU vs. ST at 14 months. Given these results, we conclude from this trial the following: (1) the MRT intervention failed to show added benefit beyond the MT intervention, (2) the

Metal Matrix Laminate Tailoring (MMLT) code: User's manual

NASA Technical Reports Server (NTRS)

Murthy, P. L. N.; Morel, M. R.; Saravanos, D. A.

1993-01-01

The User's Manual for the Metal Matrix Laminate Tailoring (MMLT) program is presented. The code is capable of tailoring the fabrication process, constituent characteristics, and laminate parameters (individually or concurrently) for a wide variety of metal matrix composite (MMC) materials, to improve the performance and identify trends or behavior of MMC's under different thermo-mechanical loading conditions. This document is meant to serve as a guide in the use of the MMLT code. Detailed explanations of the composite mechanics and tailoring analysis are beyond the scope of this document, and may be found in the references. MMLT was developed by the Structural Mechanics Branch at NASA Lewis Research Center (LeRC).

Feasibility of tailoring of press formed thermoplastic composite parts

NASA Astrophysics Data System (ADS)

Sinke, J.

2018-05-01

The Tailor Made Blank concept is widely accepted in the production of sheet metal parts. By joining, adding and subtracting materials, and sometimes even applying different alloys, parts can be produced more efficiently by cost and/or weight, and new design options have been discovered. This paper is about the manufacture of press formed parts of Fibre Reinforced Thermoplastics and the evaluation whether the Tailoring concept, though adapted to the material behavior of FRTP, can be applied to these composites as well. From research, the first results and ideas are presented. One of the ideas is the multistep forming process, creating parts with thickness variations and combinations of fibre orientations that are usually not feasible using common press forming strategies. Another idea is the blending of different prepreg materials in one component. This might be useful in case of specific details, like for areas of mechanical fastening or to avoid carbon/metal contact, otherwise resulting in severe corrosion. In a brief overview, future perspectives of the potential of the Tailoring concept are presented.

Coupled structural/thermal/electromagnetic analysis/tailoring of graded composite structures

NASA Technical Reports Server (NTRS)

Hartle, M. S.; Mcknight, R. L.; Huang, H.; Holt, R.

1992-01-01

Described here are the accomplishments of a 5-year program to develop a methodology for coupled structural, thermal, electromagnetic analysis tailoring of graded component structures. The capabilities developed over the course of the program are the analyzer module and the tailoring module for the modeling of graded materials. Highlighted accomplishments for the past year include the addition of a buckling analysis capability, the addition of mode shape slope calculation for flutter analysis, verification of the analysis modules using simulated components, and verification of the tailoring module.

The impact of tailored interventions on a community health center population.

PubMed

Rimer, B K; Conaway, M; Lyna, P; Glassman, B; Yarnall, K S; Lipkus, I; Barber, L T

1999-06-01

We conducted a 4-year randomized study in a community health center that serves primarily low income Blacks in Durham, North Carolina. Patients (1318 at baseline) were assigned randomly to one of three study groups: provider prompting intervention alone, provider prompting and tailored print materials or the previous group and tailored telephone counseling. The purpose of the study was to determine whether increasingly intensive, tailored print and telephone interventions also were increasingly effective in promoting adherence to mammograms, Pap tests and overall cancer screening compliance. Thus, the combination of tailored print interventions (print and telephone) should have been more effective than the provider prompting intervention alone, or the print intervention and prompting combination. This is one of the few studies to examine a measure of overall cancer screening compliance and to assess the benefit of combinations of tailored interventions in promoting adherence to cancer screening. Patients gave extremely high ratings to the interventions. At the bivariate level, we found a significant effect of the most intensive group (provider prompting intervention, tailored print communications and tailored telephone counseling) on Pap test compliance (P = 0.05) and borderline significance at the multivariate level (P = 0.06) as well on overall screening compliance (P = 0.06). There was not a significant effect on mammography, probably because a majority of the patients were receiving regular mammograms. We also found some important subgroup differences. For example, a larger proportion of women reported Pap tests in the tailored print and counseling group when they believed the materials were 'meant for me.' These results show that a combination of tailored interventions may have potential for reaching the women who have too often been labeled the 'hard to reach.'

Tailored metal matrix composites for high-temperature performance

NASA Technical Reports Server (NTRS)

Morel, M. R.; Saravanos, D. A.; Chamis, C. C.

1992-01-01

A multi-objective tailoring methodology is presented to maximize stiffness and load carrying capacity of a metal matrix cross-ply laminated at elevated temperatures. The fabrication process and fiber volume ratio are used as the design variables. A unique feature is the concurrent effects from fabrication, residual stresses, material nonlinearity, and thermo-mechanical loading on the laminate properties at the post-fabrication phase. For a (0/90)(sub s) graphite/copper laminate, strong coupling was observed between the fabrication process, laminate characteristics, and thermo-mechanical loading. The multi-objective tailoring was found to be more effective than single objective tailoring. Results indicate the potential to increase laminate stiffness and load carrying capacity by controlling the critical parameters of the fabrication process and the laminate.

Aeroelastic Tailoring for Stability Augmentation and Performance Enhancements of Tiltrotor Aircraft

NASA Technical Reports Server (NTRS)

Nixon, Mark W.; Piatak, David J.; Corso, Lawrence M.; Popelka, David A.

1999-01-01

The requirements for increased speed and productivity for tiltrotors has spawned several investigations associated with proprotor aeroelastic stability augmentation and aerodynamic performance enhancements. Included among these investigations is a focus on passive aeroelastic tailoring concepts which exploit the anisotropic capabilities of fiber composite materials. Researchers at Langley Research Center and Bell Helicopter have devoted considerable effort to assess the potential for using these materials to obtain aeroelastic responses which are beneficial to the important stability and performance considerations of tiltrotors. Both experimental and analytical studies have been completed to examine aeroelastic tailoring concepts for the tiltrotor, applied either to the wing or to the rotor blades. This paper reviews some of the results obtained in these aeroelastic tailoring investigations and discusses the relative merits associated with these approaches.

Randomized controlled trial of a web-based computer-tailored smoking cessation program as a supplement to nicotine patch therapy.

PubMed

Strecher, Victor J; Shiffman, Saul; West, Robert

2005-05-01

To assess the efficacy of World Wide Web-based tailored behavioral smoking cessation materials among nicotine patch users. Two-group randomized controlled trial. World Wide Web in England and Republic of Ireland. A total of 3971 subjects who purchased a particular brand of nicotine patch and logged-on to use a free web-based behavioral support program. Web-based tailored behavioral smoking cessation materials or web-based non-tailored materials. Twenty-eight-day continuous abstinence rates were assessed by internet-based survey at 6-week follow-up and 10-week continuous rates at 12-week follow-up. Using three approaches to the analyses of 6- and 12-week outcomes, participants in the tailored condition reported clinically and statistically significantly higher continuous abstinence rates than participants in the non-tailored condition. In our primary analyses using as a denominator all subjects who logged-on to the treatment site at least once, continuous abstinence rates at 6 weeks were 29.0% in the tailored condition versus 23.9% in the non-tailored condition (OR = 1.30; P = 0.0006); at 12 weeks continuous abstinence rates were 22.8% versus 18.1%, respectively (OR = 1.34; P = 0.0006). Moreover, satisfaction with the program was significantly higher in the tailored than in the non-tailored condition. The results of this study demonstrate a benefit of the web-based tailored behavioral support materials used in conjunction with nicotine replacement therapy. A web-based program that collects relevant information from users and tailors the intervention to their specific needs had significant advantages over a web-based non-tailored cessation program.

The Wear Behavior of Textured Steel Sliding against Polymers

PubMed Central

Wang, Meiling; Zhang, Changtao; Wang, Xiaolei

2017-01-01

Artificially fabricated surface textures can significantly improve the friction and wear resistance of a tribological contact. Recently, this surface texturing technique has been applied to polymer materials to improve their tribological performance. However, the wear behavior of textured tribo-pairs made of steel and polymer materials has been less thoroughly investigated and is not well understood; thus, it needs further research. The aim of this study is to investigate the wear properties of tribological contacts made of textured stainless steel against polymer surfaces. Three polymer materials were selected in this study, namely, ultrahigh molecular weight polyethylene (UHMWPE), polyoxymethylene (POM) and (polyetheretherketone) PEEK. Wear tests were operated through a ring-on-plane mode. The results revealed that the texture features and material properties affected the wear rates and friction coefficients of the textured tribo-pairs. In general, PEEK/textured steel achieved the lowest wear rate among the three types of tribo-pairs investigated. Energy dispersive x-ray spectroscopy (EDX) analysis revealed that the elements of C and O on the contacting counterfaces varied with texture features and indicated different wear behavior. Experimental and simulated results showed differences in the stress distribution around the dimple edge, which may influence wear performance. Wear debris with different surface morphologies were found for tribo-pairs with varying texture features. This study has increased the understanding of the wear behavior of tribo-pairs between textured stainless steel and polymer materials. PMID:28772688

Tribo-characteristics of self-lubricating ball bearings for the LE-7 liquid hydrogen rocket-turbopump

NASA Astrophysics Data System (ADS)

Nosaka, Masataka; Oike, Mamoru; Kikuchi, Masataka; Kamijo, Kenjiro; Tajiri, Masanori

1993-07-01

The tribo characteristics of self-lubricating 40-mm-bore ball bearings with a retainer of glass cloth-polytetrafluoroethylene (PTFE) laminate, which has elliptical pockets with a large pocket clearance, were tested under thrust loads at speeds up to 50,000 rpm, 2 million DN, in liquid hydrogen (LH2) and in liquid nitrogen (LN2). During testing, the bearing torque, outer-race temperature, and electric resistance between the inner and outer races were monitored to verify the formation and rupture of a PTFE transfer film. Testing showed that the bearings having the elliptical retainer pockets were superior to the conventional bearings with circular pockets. It was determined that, at the maximum inner race spinning velocity of about 5 m/s, a PTFE transfer film could sustain the maximum Hertz stress, up to about 2000 N/sq mm, in LH2, without severe film rupture resulting in bearing seizure. In LN2, the critical load capacity of PTFE transfer film with bearing seizure was about 2700 N/sq mm.

A tailored biocatalyst achieved by the rational anchoring of imidazole groups on a natural polymer: furnishing a potential artificial nuclease by sustainable materials engineering.

PubMed

Ferreira, José G L; Grein-Iankovski, Aline; Oliveira, Marco A S; Simas-Tosin, Fernanda F; Riegel-Vidotti, Izabel C; Orth, Elisa S

2015-04-11

Foreseeing the development of artificial enzymes by sustainable materials engineering, we rationally anchored reactive imidazole groups on gum arabic, a natural biocompatible polymer. The tailored biocatalyst GAIMZ demonstrated catalytic activity (>10(5)-fold) in dephosphorylation reactions with recyclable features and was effective in cleaving plasmid DNA, comprising a potential artificial nuclease.

Elevated-Temperature Tribology of Metallic Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blau, Peter Julian

The wear of metals and alloys takes place in many forms, and the type of wear that dominates in each instance is influenced by the mechanics of contact, material properties, the interfacial temperature, and the surrounding environment. The control of elevated-temperature friction and wear is important for applications like internal combustion engines, aerospace propulsion systems, and metalworking equipment. The progression of interacting, often synergistic processes produces surface deformation, subsurface damage accumulation, the formation of tribolayers, and the creation of free particles. Reaction products, particularly oxides, play a primary role in debris formation and microstructural evolution. Chemical reactions are known tomore » be influenced by the energetic state of the exposed surfaces, and that surface energy is in turn affected by localized deformation and fracture. At relatively low temperatures, work-hardening can occur beneath tribo-contacts, but exposure to high temperatures can modify the resultant defect density and grain structure to affect the mechanisms of re-oxidation. As research by others has shown, the rate of wear at elevated temperatures can either be enhanced or reduced, depending on contact conditions and nature of oxide layer formation. Furthermore, the thermodynamic driving force for certain chemical reactions is moderated by kinetics and microstructure. The role of deformation, oxidation, and tribo-corrosion in the elevated temperature tribology of metallic alloys will be exemplified by three examples involving sliding wear, single-point abrasion, and repetitive impact plus slip.« less

Efficient adsorption of multiple heavy metals with tailored silica aerogel-like materials.

PubMed

Vareda, João P; Durães, Luisa

2017-11-10

Recently developed tailored adsorbents for heavy metal uptake are studied in batch tests with Cu, Pb, Cd, Ni, Cr and Zn, in order to decontaminate polluted environments where these heavy metals are found in solution - water courses and groundwater. The adsorbents feature mercapto or amine-mercapto groups that are capable of complexating the cations. Through the use of equilibrium tests it is found that a remarkably high heavy metal uptake is obtained for all metals (ranging from 84 to 140 mg/g). These uptake values are quite impressive when compared to other adsorbents reported in the literature, which is also due to the double functionalization present in one of the adsorbents. For the best adsorbent, adsorption capacities followed the order Cu(II) > Pb(II) > Zn(II) > Cr(III) > Cd(II) > Ni(II). With these adsorbents, the removal process was fast with most of the metals being removed in less than 1 h. Competitive sorption tests were performed in tertiary mixtures that were based on real world polluted sites. It was found that although competitive sorption occurs, affecting the individual removal of each metal, all the cations in solution still interact with the adsorbent, achieving removal values that make this type of material very interesting for its proposed application.

Shape-tailored polymer colloids on the road to become structural motifs for hierarchically organized materials.

PubMed

Plüisch, Claudia Simone; Wittemann, Alexander

2013-12-01

Anisometric polymer colloids are likely to behave differently when compared with centrosymmetric particles. Their study may not only shine new light on the organization of matter; they may also serve as building units with specific symmetries and complexity to build new materials from them. Polymer colloids of well-defined complex geometries can be obtained by packing a limited number of spherical polymer particles into clusters with defined configurations. Such supracolloidal architectures can be fabricated at larger scales using narrowly dispersed emulsion droplets as templates. Assemblies built from at least two different types of particles as elementary building units open perspectives in selective targeting of colloids with specific properties, aiming for mesoscale building blocks with tailor-made morphologies and multifunctionality. Polymer colloids with defined geometries are also ideal to study shape-dependent properties such as the diffusion of complex particles. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Tailored material properties using textile composites

NASA Astrophysics Data System (ADS)

Pastore, C. M.

2017-10-01

Lightweighting is essential for the reduction of energy consumption in transportation. The most common approach is through the application of high specific strength and stiffness materials, such as composites and high performance aluminum alloys. One of the challenges associated with the use of advanced materials is the high cost. This paper explores the opportunities of using hybrid composites (glass and carbon, for example) with selective fiber placement to optimize the weight subject to price constraints for given components. Considering the example of a hat-section for hood reinforcement, different material configurations were modeled and developed. The required thickness of the hat section to meet the same bending stiffness as an all carbon composite beam was calculated. It was shown that selective placement of fiber around the highest moments results in a weight savings of around 14% compared to a uniformly blended hybrid with the same total material configuration. From this it is possible to estimate the materials cost of the configurations as well as the weight of the component. To determine which is best it is necessary to find an exchange constant that converts weight into cost - the penalty of carrying the extra weight. The value of this exchange constant will depend on the particular application.

Effectiveness of different methods for delivering tailored nutrition education to low income, ethnically diverse adults

PubMed Central

Gans, Kim M; Risica, Patricia M; Strolla, Leslie O; Fournier, Leanne; Kirtania, Usree; Upegui, David; Zhao, Julie; George, Tiffiney; Acharyya, Suddhasatta

2009-01-01

Background Computer-tailored written nutrition interventions have been shown to be more effective than non-tailored materials in changing diet, but continued research is needed. Your Healthy Life/Su Vida Saludable (YHL-SVS) was an intervention study with low income, ethnically diverse, English and Spanish-speaking participants to determine which methods of delivering tailored written nutrition materials were most effective in lowering fat and increasing fruit and vegetable (F&V) intake. Methods YHL-SVS was a randomized controlled trial with four experimental conditions: 1) Nontailored (NT) comparison group; 2) Single Tailored (ST) packet; 3) Multiple Tailored (MT) packet mailed in four installments; 4) Multiple Re-Tailored (MRT) MT packets re-tailored between mailings via brief phone surveys. A baseline telephone survey collected information for tailoring as well as evaluation. Follow-up evaluation surveys were collected 4- and 7-months later. Primary outcomes included F&V intake and fat related behaviors. Descriptive statistics, paired t-test and ANOVA were used to examine the effectiveness of different methods of delivering tailored nutrition information. Results Both the ST and MT groups reported significantly higher F&V intake at 4-months than the NT and MRT groups. At 7 months, only the MT group still had significantly higher F&V intake compared to the NT group. For changes in fat-related behaviors, both the MT and MRT groups showed more change than NT at 4 months, but at 7 months, while these differences persisted, they were no longer statistically significant. There was a significant interaction of experimental group by education for change in F&V intake (P = .0085) with the lowest educational group demonstrating the most change. Conclusion In this study, tailored interventions were more effective than non-tailored interventions in improving the short-term dietary behaviors of low income, ethnically diverse participants. Delivery of information in multiple

Secretos de la Buena Vida: processes of dietary change via a tailored nutrition communication intervention for Latinas

PubMed Central

Baquero, Barbara; Ayala, Guadalupe X.; Arredondo, Elva M.; Campbell, Nadia R.; Slymen, Donald J.; Gallo, Linda; Elder, John P.

2009-01-01

Secretos de la Buena Vida was a successful tailored nutrition communication intervention delivered to Latinas living along the US–Mexico border in California. The intervention was delivered over a 14-week period and consisted of three intervention conditions: weekly home visits with promotoras + weekly tailored mailed newsletters in the first condition, weekly tailored mailed newsletters in the second condition and targeted materials in the attention control condition. The current study examined what elements of the promotora + tailored newsletter and tailored newsletter-only conditions were most effective for behavioral adoption and maintenance in a sample of 238 Latina women. Process evaluation measures assessed the implementation, fidelity and dose of these two intervention conditions. Results indicate that there was high fidelity to program implementation and delivery. Perceived effort, perceived support and intervention length predicted adoption of a lower fat diet at the 15-month follow-up. In the promotora + tailored newsletter condition, married women were four times more likely to be adopters of dietary fat changes than single women. These findings highlight the importance of process evaluation measures and help us understand the mechanism by which tailored print materials and interpersonal health communication via promotoras can facilitate health behavior change. PMID:19339374

Aeroelastic Tailoring of Transport Wings Including Transonic Flutter Constraints

NASA Technical Reports Server (NTRS)

Stanford, Bret K.; Wieseman, Carol D.; Jutte, Christine V.

2015-01-01

Several minimum-mass optimization problems are solved to evaluate the effectiveness of a variety of novel tailoring schemes for subsonic transport wings. Aeroelastic stress and panel buckling constraints are imposed across several trimmed static maneuver loads, in addition to a transonic flutter margin constraint, captured with aerodynamic influence coefficient-based tools. Tailoring with metallic thickness variations, functionally graded materials, balanced or unbalanced composite laminates, curvilinear tow steering, and distributed trailing edge control effectors are all found to provide reductions in structural wing mass with varying degrees of success. The question as to whether this wing mass reduction will offset the increased manufacturing cost is left unresolved for each case.

Targeted Cellular Drug Delivery using Tailored Dendritic Nanostructures

NASA Astrophysics Data System (ADS)

Kannan, Rangaramanujam; Kolhe, Parag; Kannan, Sujatha; Lieh-Lai, Mary

2002-03-01

Dendrimers and hyperbranched polymers possess highly branched architectures, with a large number of controllable, tailorble, ‘peripheral’ functionalities. Since the surface chemistry of these materials can be modified with relative ease, these materials have tremendous potential in targeted drug and gene delivery. The large number of end groups can also be tailored to create special affinity to targeted cells, and can also encapsulate drugs and deliver them in a controlled manner. We are developing tailor-modified dendritic systems for drug delivery. Synthesis, in-vitro drug loading, in-vitro drug delivery, and the targeting efficiency to the cell are being studied systematically using a wide variety of experimental tools. Polyamidoamine and Polyol dendrimers, with different generations and end-groups are studied, with drugs such as Ibuprofen and Methotrexate. Our results indicate that a large number of drug molecules can be encapsulated/attached to the dendrimers, depending on the end groups. The drug-encapsulated dendrimer is able to enter the cells rapidly and deliver the drug. Targeting strategies being explored

Automated Finite Element Analysis of Elastically-Tailored Plates

NASA Technical Reports Server (NTRS)

Jegley, Dawn C. (Technical Monitor); Tatting, Brian F.; Guerdal, Zafer

2003-01-01

A procedure for analyzing and designing elastically tailored composite laminates using the STAGS finite element solver has been presented. The methodology used to produce the elastic tailoring, namely computer-controlled steering of unidirectionally reinforced composite material tows, has been reduced to a handful of design parameters along with a selection of construction methods. The generality of the tow-steered ply definition provides the user a wide variety of options for laminate design, which can be automatically incorporated with any finite element model that is composed of STAGS shell elements. Furthermore, the variable stiffness parameterization is formulated so that manufacturability can be assessed during the design process, plus new ideas using tow steering concepts can be easily integrated within the general framework of the elastic tailoring definitions. Details for the necessary implementation of the tow-steering definitions within the STAGS hierarchy is provided, and the format of the ply definitions is discussed in detail to provide easy access to the elastic tailoring choices. Integration of the automated STAGS solver with laminate design software has been demonstrated, so that the large design space generated by the tow-steering options can be traversed effectively. Several design problems are presented which confirm the usefulness of the design tool as well as further establish the potential of tow-steered plies for laminate design.

Cost-effectiveness of targeted and tailored interventions on colorectal cancer screening use.

PubMed

Lairson, David R; DiCarlo, Melissa; Myers, Ronald E; Wolf, Thomas; Cocroft, James; Sifri, Randa; Rosenthal, Michael; Vernon, Sally W; Wender, Richard

2008-02-15

Colorectal cancer (CRC) screening is cost-effective but underused. The objective of this study was to determine the cost-effectiveness of targeted and tailored behavioral interventions to increase CRC screening use by conducting an economic analysis associated with a randomized trial among patients in a large, racially and ethnically diverse, urban family practice in Philadelphia. The incremental costs per unit increase were measured in individuals who were screened during the 24 months after intervention. Percent increase in screening was adjusted for baseline differences in the study groups. Each intervention arm received a targeted screening invitation letter, stool blood test (SBT) cards, informational booklet, and reminder letter. Tailored interventions incrementally added tailored messages and reminder telephone calls. Program costs of the targeted intervention were 42 dollars per participant. Additional costs of adding tailored print materials and of delivering a reminder telephone call were 150 dollars and 200 dollars per participant, respectively. The cost per additional individual screened was 319 dollars when comparing the no intervention group with the targeted intervention group. The targeted intervention was more effective and less costly than the tailored intervention. Although tailoring plus reminder telephone call was the most effective strategy, it was very costly per additional individual screened. Mailed SBT cards significantly boosted CRC screening use. However, going beyond the targeted intervention to include tailoring or tailoring plus reminder calls in the manner used in this study did not appear to be an economically attractive strategy. Cancer 2008. (c) 2007 American Cancer Society.

Tailored Testing Theory and Practice: A Basic Model, Normal Ogive Submodels, and Tailored Testing Algorithms

DTIC Science & Technology

1983-08-01

ACCESSION NO «• TITLE (and Sublltle) TAILORED TESTING THEORY AND PRACTICE: A BASIC MODEL , NORMAL OGIVE SUBMODELS, AND TAILORED TESTING ALGORITHMS 7...single common-factor model , the author derives the two- and three-parametir normal ogfve il’^irTr^ functions as submodels. For both of these...PAOEfWiwi Dmia Bnfnd) NPRDC TR 83-32 AUGUST 1983 TAILORED TESTING THEORY AND PRACTICE: A BASIC MODEL , NORMAL OGIVE SUBMODELS, AND TAILORED TESTING

Development of 2D and 3D structured textile batteries processing conductive material with Tailored Fiber Placement (TFP)

NASA Astrophysics Data System (ADS)

Normann, M.; Grethe, T.; Zöll, K.; Ehrmann, A.; Schwarz-Pfeiffer, A.

2017-10-01

In recent years smart textiles have gained a significant increase of attention. Electrotherapeutic socks, light emitting dresses or shirts with integrated sensors, having the ability to process data of vital parameters, are just a few examples and the full potential is not yet exhausted: Smart textiles are not only used for clothing purposes. Sensors for the care of the elderly, light applications for home textiles and monitoring systems in the automotive section are promising fields for the future. For all these electrical and electronic features, the supply of power is needed. The most common used power supplies, however, are not flexible, often not lightweight and therefore a huge problem for the integration into textile products. In recent projects, textile-based batteries are being developed. Metal-coated fabrics and yarns (e.g. silver, copper, nickel, zinc) as well as carbon based materials were used to create textile based energy sources. This article gives an overview of textile based electrochemical cells by combining different conductive yarns and a gel-electrolyte. The available materials will be processed by embroidering utilizing tailored fiber placement (TFP). The electrical characteristics of different embroidered patterns and material combinations are examined.

Effectiveness of individually tailored smoking cessation advice letters as an adjunct to telephone counselling and generic self-help materials: randomized controlled trial.

PubMed

Sutton, Stephen; Gilbert, Hazel

2007-06-01

To evaluate the effectiveness of individually tailored smoking cessation advice letters as an adjunct to telephone counselling and generic self-help materials. Randomized controlled trial. The UK Quitline. A total of 1508 current smokers and recent ex-smokers. The control group received usual care (telephone counselling and an information pack sent through the post). The intervention group received in addition a computer-generated individually tailored advice letter. All outcomes were assessed at 6-month follow-up. The primary outcome measure was self-reported prolonged abstinence for at least 3 months. Secondary outcomes were self-reported prolonged abstinence for at least 1 month and 7-day and 24-hour point-prevalence abstinence. For the sample as a whole, quit rates did not differ significantly between the two conditions. However, among the majority (n = 1164) who were smokers at baseline, quit rates were consistently higher in the intervention group: prolonged abstinence for 3 months, 12.2% versus 9.0% [odds ratio (OR) = 1.40, 95% confidence interval (CI) = 0.96-2.04, P = 0.080); prolonged abstinence for 1 month, 16.4% versus 11.3% (OR = 1.53, 95% CI = 1.09-2.15, P = 0.013); 7-day point-prevalence abstinence, 18.9% versus 12.7% (OR = 1.59, 95% CI = 1.15-2.19, P = 0.004); 24-hour point-prevalence abstinence, 20.9% versus 15.4% (OR = 1.45, 95% CI = 1.07-1.96, P = 0.015). The results for the smokers are encouraging in showing a small but useful effect of the tailored letter on quit rate. Versions of the tailoring program could be used on the web and in general practices, pharmacies and primary care trusts.

Aerogels in Chemical Engineering: Strategies Toward Tailor-Made Aerogels.

PubMed

Smirnova, Irina; Gurikov, Pavel

2017-06-07

The present review deals with recent advances in the rapidly growing field of aerogel research and technology. The major focus of the review lies in approaches that allow tailoring of aerogel properties to meet application-driven requirements. The decisive properties of aerogels are discussed with regard to existing and potential application areas. Various tailoring strategies, such as modulation of the pore structure, coating, surface modification, and post-treatment, are illustrated by results of the last decade. In view of commercialization of aerogel-based products, a panorama of current industrial aerogel suppliers is given, along with a discussion of possible alternative sources for raw materials and precursors. Finally, growing points and perspectives of the aerogel field are summarized.

Effectiveness of web-based tailored smoking cessation advice reports (iQuit): a randomized trial.

PubMed

Mason, Dan; Gilbert, Hazel; Sutton, Stephen

2012-12-01

To determine whether web-based tailored cessation advice, based on social cognitive theory and the perspectives on change model, was more effective in aiding a quit attempt than broadly similar web-based advice that was not tailored. Participants were allocated randomly to one of two groups, to receive either a cessation advice report and progress report that were tailored to individual-level characteristics or a cessation advice report that presented standardized (non-tailored) content. Tailoring was based on smoking-related beliefs, personal characteristics and smoking patterns, self-efficacy and outcome expectations. Participant enrolment and baseline assessments were conducted remotely online via the study website, with the advice reports presented by the same website. Participants (n = 1758) were visitors to the QUIT website who were based in the United Kingdom, aged 18 years or over and who smoked cigarettes or hand-rolled tobacco. Follow-up assessments were made at 6 months by telephone interview. The primary outcome measure was self-reported 3 months prolonged abstinence, and secondary outcomes were 1 month prolonged abstinence, 7-day and 24-hour point prevalence abstinence. The intervention group did not differ from the control group on the primary outcome (9.1% versus 9.3%; odds ratio = 1.02 95% confidence interval 0.73-1.42) or on any of the secondary outcomes. Intervention participants gave more positive evaluations of the materials than control participants. A web-based intervention that tailored content according to smoking-related beliefs, personal characteristics and smoking patterns, self-efficacy and outcome expectations, was not more effective than web-based materials presenting broadly similar non-tailored information. © 2012 The Authors, Addiction © 2012 Society for the Study of Addiction.

Lay Health Influencers: How They Tailor Brief Tobacco Cessation Interventions

PubMed Central

Yuan, Nicole P.; Castañeda, Heide; Nichter, Mark; Nichter, Mimi; Wind, Steven; Carruth, Lauren; Muramoto, Myra

2014-01-01

Interventions tailored to individual smoker characteristics have increasingly received attention in the tobacco control literature. The majority of tailored interventions are generated by computers and administered with printed materials or Web-based programs. The purpose of this study was to examine the tailoring activities of community lay health influencers who were trained to perform face-to-face brief tobacco cessation interventions. Eighty participants of a large-scale, randomized controlled trial completed a 6-week qualitative follow-up interview. A majority of participants (86%) reported that they made adjustments in their intervention behaviors based on individual smoker characteristics, their relationship with the smoker, and/or setting. Situational contexts (i.e., location and timing) primarily played a role after targeted smokers were selected. The findings suggest that lay health influencers benefit from a training curriculum that emphasizes a motivational, person-centered approach to brief cessation interventions. Recommendations for future tobacco cessation intervention trainings are presented. PMID:21986244

Lay health influencers: how they tailor brief tobacco cessation interventions.

PubMed

Yuan, Nicole P; Castañeda, Heide; Nichter, Mark; Nichter, Mimi; Wind, Steven; Carruth, Lauren; Muramoto, Myra

2012-10-01

Interventions tailored to individual smoker characteristics have increasingly received attention in the tobacco control literature. The majority of tailored interventions are generated by computers and administered with printed materials or web-based programs. The purpose of this study was to examine the tailoring activities of community lay health influencers who were trained to perform face-to-face brief tobacco cessation interventions. Eighty participants of a large-scale, randomized controlled trial completed a 6-week qualitative follow-up interview. A majority of participants (86%) reported that they made adjustments in their intervention behaviors based on individual smoker characteristics, their relationship with the smoker, and/or setting. Situational contexts (i.e., location and timing) primarily played a role after targeted smokers were selected. The findings suggest that lay health influencers benefit from a training curriculum that emphasizes a motivational, person-centered approach to brief cessation interventions. Recommendations for future tobacco cessation intervention trainings are presented.

Manufacturing of tailored tubes with a process integrated heat treatment

NASA Astrophysics Data System (ADS)

Hordych, Illia; Boiarkin, Viacheslav; Rodman, Dmytro; Nürnberger, Florian

2017-10-01

The usage of work-pieces with tailored properties allows for reducing costs and materials. One example are tailored tubes that can be used as end parts e.g. in the automotive industry or in domestic applications as well as semi-finished products for subsequent controlled deformation processes. An innovative technology to manufacture tubes is roll forming with a subsequent inductive heating and adapted quenching to obtain tailored properties in the longitudinal direction. This processing offers a great potential for the production of tubes with a wide range of properties, although this novel approach still requires a suited process design. Based on experimental data, a process simulation is being developed. The simulation shall be suitable for a virtual design of the tubes and allows for gaining a deeper understanding of the required processing. The model proposed shall predict microstructural and mechanical tube properties by considering process parameters, different geometries, batch-related influences etc. A validation is carried out using experimental data of tubes manufactured from various steel grades.

Process Design of Aluminum Tailor Heat Treated Blanks

PubMed Central

Kahrimanidis, Alexander; Lechner, Michael; Degner, Julia; Wortberg, Daniel; Merklein, Marion

2015-01-01

In many industrials field, especially in the automotive sector, there is a trend toward lightweight constructions in order to reduce the weight and thereby the CO2 and NOx emissions of the products. An auspicious approach within this context is the substitution of conventional deep drawing steel by precipitation hardenable aluminum alloys. However, based on the low formability, the application for complex stamping parts is challenging. Therefore, at the Institute of Manufacturing Technology, an innovative technology to enhance the forming limit of these lightweight materials was invented. The key idea of the so-called Tailor Heat Treated Blanks (THTB) is optimization of the mechanical properties by local heat treatment before the forming operation. An accurate description of material properties is crucial to predict the forming behavior of tailor heat treated blanks by simulation. Therefore, within in this research project, a holistic approach for the design of the THTB process in dependency of the main influencing parameters is presented and discussed in detail. The capability of the approach for the process development of complex forming operations is demonstrated by a comparison of local blank thickness of a tailgate with the corresponding results from simulation. PMID:28793727

Process Design of Aluminum Tailor Heat Treated Blanks.

PubMed

Kahrimanidis, Alexander; Lechner, Michael; Degner, Julia; Wortberg, Daniel; Merklein, Marion

2015-12-09

In many industrials field, especially in the automotive sector, there is a trend toward lightweight constructions in order to reduce the weight and thereby the CO₂ and NO x emissions of the products. An auspicious approach within this context is the substitution of conventional deep drawing steel by precipitation hardenable aluminum alloys. However, based on the low formability, the application for complex stamping parts is challenging. Therefore, at the Institute of Manufacturing Technology, an innovative technology to enhance the forming limit of these lightweight materials was invented. The key idea of the so-called Tailor Heat Treated Blanks (THTB) is optimization of the mechanical properties by local heat treatment before the forming operation. An accurate description of material properties is crucial to predict the forming behavior of tailor heat treated blanks by simulation. Therefore, within in this research project, a holistic approach for the design of the THTB process in dependency of the main influencing parameters is presented and discussed in detail. The capability of the approach for the process development of complex forming operations is demonstrated by a comparison of local blank thickness of a tailgate with the corresponding results from simulation.

Effect of tailoring in an internet-based intervention for smoking cessation: randomized controlled trial.

PubMed

Wangberg, Silje C; Nilsen, Olav; Antypas, Konstantinos; Gram, Inger Torhild

2011-12-15

Studies suggest that tailored materials are superior to nontailored materials in supporting health behavioral change. Several trials on tailored Internet-based interventions for smoking cessation have shown good effects. There have, however, been few attempts to isolate the effect of the tailoring component of an Internet-based intervention for smoking cessation and to compare it with the effectiveness of the other components. The study aim was to isolate the effect of tailored emails in an Internet-based intervention for smoking cessation by comparing two versions of the intervention, with and without tailored content. We conducted a two-arm, randomized controlled trial of the open and free Norwegian 12-month follow-up, fully automated Internet-based intervention for smoking cessation, slutta.no. We collected information online on demographics, smoking, self-efficacy, use of the website, and participant evaluation at enrollment and subsequently at 1, 3, and 12 months. Altogether, 2298 self-selected participants aged 16 years or older registered at the website between August 15, 2006 and December 7, 2007 and were randomly assigned to either a multicomponent, nontailored Internet-based intervention for smoking cessation (control) or a version of the same Internet-based intervention with tailored content delivered on the website and via email. Of the randomly assigned participants, 116 (of 419, response rate = 27.7%) in the intervention group and 128 (of 428, response rate = 29.9%) in the control group had participated over the 12 months and responded at the end of follow-up. The 7-day intention-to-treat abstinence rate at 1 month was 15.2% (149/982) among those receiving the tailored intervention, compared with 9.4% (94/999) among those who received the nontailored intervention (P < .001). The corresponding figures at 3 months were 13.5% (122/902) and 9.4% (84/896, P =.006) and at 12 months were 11.2% (47/419) and 11.7% (50/428, P = .91). Likewise, the intervention

Tailoring graphene layer-to-layer growth

NASA Astrophysics Data System (ADS)

Li, Yongtao; Wu, Bin; Guo, Wei; Wang, Lifeng; Li, Jingbo; Liu, Yunqi

2017-06-01

A layered material grown between a substrate and the upper layer involves complex interactions and a confined reaction space, representing an unusual growth mode. Here, we show multi-layer graphene domains grown on liquid or solid Cu by the chemical vapor deposition method via this ‘double-substrate’ mode. We demonstrate the interlayer-induced coupling effect on the twist angle in bi- and multi-layer graphene. We discover dramatic growth disunity for different graphene layers, which is explained by the ideas of a chemical ‘gate’ and a material transport process within a confined space. These key results lead to a consistent framework for understanding the dynamic evolution of multi-layered graphene flakes and tailoring the layer-to-layer growth for practical applications.

Evaluation of motivationally tailored vs. standard self-help physical activity interventions at the workplace.

PubMed

Marcus, B H; Emmons, K M; Simkin-Silverman, L R; Linnan, L A; Taylor, E R; Bock, B C; Roberts, M B; Rossi, J S; Abrams, D B

1998-01-01

This study compares the efficacy of a self-help intervention tailored to the individual's stage of motivational readiness for exercise adoption with a standard self-help exercise promotion intervention. Interventions were delivered at baseline and 1 month; assessments were collected at baseline and 3 months. Eleven worksites participating in the Working Healthy Research Trial. Participants (n = 1559) were a subsample of employees at participating worksites, individually randomized to one of two treatment conditions. Printed self-help exercise promotion materials either (1) matched to the individual's stage of motivational readiness for exercise adoption (motivationally tailored), or (2) standard materials (standard). Measures of stage of motivational readiness for exercise and items from the 7-Day Physical Activity Recall. Among intervention completers (n = 903), chi-square analyses showed that, compared to the standard intervention, those receiving the motivationally tailored intervention were significantly more likely to show increases (37% vs. 27%) and less likely to show either no change (52% vs. 58%) or regression (11% vs. 15%) in stage of motivational readiness. Multivariate analyses of variance showed that changes in stage of motivational readiness were significantly associated with changes in self-reported time spent in exercise. This is the first prospective, randomized, controlled trial demonstrating the efficacy of a brief motivationally tailored intervention compared to a standard self-help intervention for exercise adoption. These findings appear to support treatment approaches that tailor interventions to the individual's stage of motivational readiness for exercise adoption.

Sputter-Coated Microparticle Additives for Tailored Optical Properties

DTIC Science & Technology

2016-09-01

hour at best). The microspheres coated in this work will be incorporated into a polymer matrix for composite and large-area coating applications...demonstrated, they will be incorporated into a polymer matrix for further testing. 15. SUBJECT TERMS fluidized bed, thin film, microparticles, coating...films of metals, ceramics , and multilayered materials.1 This is a practical method for the batch production of microparticles with tailored optical

Tailorable Dielectric Material with Complex Permittivity Characteristics

NASA Technical Reports Server (NTRS)

Smith, Joseph G. (Inventor); Watson, Kent A. (Inventor); Elliott, Holly A (Inventor); Delozier, Donavon Mark (Inventor); Connell, John W. (Inventor); Ghose, Sayata (Inventor); Dudley, Kenneth L. (Inventor)

2014-01-01

A dielectric material includes a network of nanosubstrates, such as but not limited to nanotubes, nanosheets, or other nanomaterials or nanostructures, a polymer base material or matrix, and nanoparticles constructed at least partially of an elemental metal. The network has a predetermined nanosubstrate loading percentage by weight with respect to a total weight of the dielectric material, and a preferential or predetermined longitudinal alignment with respect to an orientation of an incident electrical field. A method of forming the dielectric material includes depositing the metal-based nanoparticles onto the nanosubstrates and subsequently mixing these with a polymer matrix. Once mixed, alignment can be achieved by melt extrusion or a similar mechanical shearing process. Alignment of the nanosubstrate may be in horizontal or vertical direction with respect to the orientation of an incident electrical field.

Tailored porous silicon microparticles: fabrication and properties

PubMed Central

Chiappini, Ciro; Tasciotti, Ennio; Fakhoury, Jean R.; Fine, Daniel; Pullan, Lee; Wang, Young-Chung; Fu, Lianfeng

2010-01-01

The use of mesoporous silicon particles for drug delivery has been widely explored thanks to their biodegradability and biocompatibility. The ability to tailor the physicochemical properties of porous silicon at the micro and nano scale confers versatility to this material. We present a method for the fabrication of highly reproducible, monodisperse mesoporous silicon particles with controlled physical characteristics through electrochemical etch of patterned silicon trenches. We tailored particle size in the micrometer range and pore size in the nanometer range, shape from tubular to discoidal to hemispherical, and porosity from 46% to over 80%. In addition, we correlated the properties of the porous matrix with the loading of model nanoparticles (Q-dots) and observed their three-dimensional arrangement within the matrix by transmission electron microscopy tomography. The methods developed in this study provide effective means to fabricate mesoporous silicon particles according to the principles of rational design for therapeutic vectors and to characterize the distribution of nanoparticles within the porous matrix PMID:20162656

FE Simulation Models for Hot Stamping an Automobile Component with Tailor-Welded High-Strength Steels

NASA Astrophysics Data System (ADS)

Tang, Bingtao; Wang, Qiaoling; Wei, Zhaohui; Meng, Xianju; Yuan, Zhengjun

2016-05-01

Ultra-high-strength in sheet metal parts can be achieved with hot stamping process. To improve the crash performance and save vehicle weight, it is necessary to produce components with tailored properties. The use of tailor-welded high-strength steel is a relatively new hot stamping process for saving weight and obtaining desired local stiffness and crash performance. The simulation of hot stamping boron steel, especially tailor-welded blanks (TWBs) stamping, is more complex and challenging. Information about thermal/mechanical properties of tools and sheet materials, heat transfer, and friction between the deforming material and the tools is required in detail. In this study, the boron-manganese steel B1500HS and high-strength low-alloy steel B340LA are tailor welded and hot stamped. In order to precisely simulate the hot stamping process, modeling and simulation of hot stamping tailor-welded high-strength steels, including phase transformation modeling, thermal modeling, and thermal-mechanical modeling, is investigated. Meanwhile, the welding zone of tailor-welded blanks should be sufficiently accurate to describe thermal, mechanical, and metallurgical parameters. FE simulation model using TWBs with the thickness combination of 1.6 mm boron steel and 1.2 mm low-alloy steel is established. In order to evaluate the mechanical properties of the hot stamped automotive component (mini b-pillar), hardness and microstructure at each region are investigated. The comparisons between simulated results and experimental observations show the reliability of thermo-mechanical and metallurgical modeling strategies of TWBs hot stamping process.

Trim and Structural Optimization of Subsonic Transport Wings Using Nonconventional Aeroelastic Tailoring

NASA Technical Reports Server (NTRS)

Stanford, Bret K.; Jutte, Christine V.

2014-01-01

Several minimum-mass aeroelastic optimization problems are solved to evaluate the effectiveness of a variety of novel tailoring schemes for subsonic transport wings. Aeroelastic strength and panel buckling constraints are imposed across a variety of trimmed maneuver loads. Tailoring with metallic thickness variations, functionally graded materials, composite laminates, tow steering, and distributed trailing edge control effectors are all found to provide reductions in structural wing mass with varying degrees of success. The question as to whether this wing mass reduction will offset the increased manufacturing cost is left unresolved for each case.

Cost effectiveness of computer tailored and non-tailored smoking cessation letters in general practice: randomised controlled trial

PubMed Central

Lennox, A Scott; Osman, Liesl M; Reiter, Ehud; Robertson, Roma; Friend, James; McCann, Ian; Skatun, Diane; Donnan, Peter T

2001-01-01

Objectives To develop and evaluate, in a primary care setting, a computerised system for generating tailored letters about smoking cessation. Design Randomised controlled trial. Setting Six general practices in Aberdeen, Scotland. Participants 2553 smokers aged 17 to 65. Interventions All participants received a questionnaire asking about their smoking. Participants subsequently received either a computer tailored or a non-tailored, standard letter on smoking cessation, or no letter. Main outcome measures Prevalence of validated abstinence at six months; change in intention to stop smoking in the next six months. Results The validated cessation rate at six months was 3.5% (30/857) (95% confidence interval 2.3% to 4.7%) for the tailored letter group, 4.4% (37/846) (3.0% to 5.8%) for the non-tailored letter group, and 2.6% (22/850) (1.5% to 3.7%) for the control (no letter) group. After adjustment for significant covariates, the cessation rate was 66% greater (−4% to 186%; P=0.07) in the non-tailored letter group than that in the no letter group. Among participants who smoked <20 cigarettes per day, the cessation rate in the non-tailored letter group was 87% greater (0% to 246%; P=0.05) than that in the no letter group. Among heavy smokers who did not quit, a 76% higher rate of positive shift in “stage of change” (intention to quit within a particular period of time) was seen compared with those who received no letter (11% to 180%; P=0.02). The increase in cost for each additional quitter in the non-tailored letter group compared with the no letter group was £89. Conclusions In a large general practice, a brief non-tailored letter effectively increased cessation rates among smokers. A tailored letter was not effective in increasing cessation rates but promoted shift in movement towards cessation (“stage of change”) in heavy smokers. As a pragmatic tool to encourage cessation of smoking, a mass mailing of non-tailored letters from general practices is more

T & I--Tailoring. Kit No. 50. Instructor's Manual [and] Student Learning Activity Guide.

ERIC Educational Resources Information Center

Wilkins, Thelma

An instructor's manual and student activity guide on tailoring are provided in this set of prevocational education materials which focuses on the vocational area of trade and industry. (This set of materials is one of ninety-two prevocational education sets arranged around a cluster of seven vocational offerings: agriculture, home economics,…

Factors that influence the efficiency of a fluidized-bed-type tribo-electrostatic separator for mixed granular plastics

NASA Astrophysics Data System (ADS)

Dascalescu, L.; Fati, O.; Bilici, M.; Rahou, F.; Dragan, C.; Samuila, A.; Iuga, A.

2011-06-01

Fluidized bed devices have already been used as tribochargers for various industrial electrostatic separation processes. In the present paper, the authors investigate the behaviour of polyamide - polycarbonate granular plastic mixtures in a parallelepiped bed, the height of which is roughly 2 times its length or width, so that the collisions between granules become the prevailing tribocharging mechanism. Two of the opposite walls of the tribocharging chamber consist of metallic plates connected to two DC high-voltage supplies of opposite polarities, so that the charged particles are attracted to the electrodes and separated while still in the fluidized state. The collecting hoppers are designed as Faraday cups connected to two electrometers, thus allowing the instantaneous measurement of the charge carried by the separated particles. Experimental design methodology was employed for the optimization of the tribo-aero-electrostatic separation process, the input variables being the high-voltage applied to the electrodes and the duration of the tribocharging. Higher voltages applied to the electrode system do not necessarily lead to larger quantities of collected products but improve the purity of the concentrates. The composition of the mixture influences the outcome of the process.

Design and results of a culturally tailored cancer outreach project by and for Micronesian women.

PubMed

Aitaoto, Nia; Braun, Kathryn L; Estrella, Julia; Epeluk, Aritae; Tsark, JoAnn

2012-01-01

In 2005, approximately 26% of Micronesian women aged 40 or older in Hawai'i used mammography for breast cancer screening. We describe an 18-month project to increase screening participation in this population by tailoring educational materials and using a lay educator approach. New immigrants to Hawai'i are Marshallese from the Republic of the Marshall Islands and Chuukese, Pohnpeians, and Kosraeans from the Federated States of Micronesia. In Hawai'i, these 4 groups refer to themselves collectively as Micronesians, although each group has its own distinct culture and language. From 2006 through 2007, we applied principles of community-based participatory research--trust building, joint assessment, cultural tailoring of materials, and skills transfer--to develop and track the reach of Micronesian women lay educators in implementing a cancer awareness program among Micronesian women living in Hawai'i. Using our tailored in-language materials, 11 lay educators (5 Chuukese, 3 Marshallese, 2 Pohnpeians, and 1 Kosraean) provided one-on-one and small group in-language cancer information sessions to 567 Micronesian women (aged 18-75 years). Among the 202 women aged 40 or older eligible for mammography screening, 166 (82%) had never had a mammogram and were assisted to screening appointments. After 6 months, 146 (88%) of the 166 had received a mammogram, increasing compliance from 18% to 90%. Lay educators reported increases in their skills and their self-esteem and want to extend their skills to other health issues, including diabetes management and immunization. Tailoring materials and using the lay educator model successfully increased participation in breast cancer screening. This model may work in other communities that aim to reduce disparities in access to cancer screening.

Employee Perceptions of Workplace Health Promotion Programs: Comparison of a Tailored, Semi-Tailored, and Standardized Approach.

PubMed

Street, Tamara D; Lacey, Sarah J

2018-04-28

In the design of workplace health promotion programs (WHPPs), employee perceptions represent an integral variable which is predicted to translate into rate of user engagement (i.e., participation) and program loyalty. This study evaluated employee perceptions of three workplace health programs promoting nutritional consumption and physical activity. Programs included: (1) an individually tailored consultation with an exercise physiologist and dietitian; (2) a semi-tailored 12-week SMS health message program; and (3) a standardized group workshop delivered by an expert. Participating employees from a transport company completed program evaluation surveys rating the overall program, affect, and utility of: consultations ( n = 19); SMS program ( n = 234); and workshops ( n = 86). Overall, participants’ affect and utility evaluations were positive for all programs, with the greatest satisfaction being reported in the tailored individual consultation and standardized group workshop conditions. Furthermore, mode of delivery and the physical presence of an expert health practitioner was more influential than the degree to which the information was tailored to the individual. Thus, the synergy in ratings between individually tailored consultations and standardized group workshops indicates that low-cost delivery health programs may be as appealing to employees as tailored, and comparatively high-cost, program options.

"Click chemistry" in tailor-made polymethacrylates bearing reactive furfuryl functionality: a new class of self-healing polymeric material.

PubMed

Kavitha, A Amalin; Singha, Nikhil K

2009-07-01

This investigation reports the effective use of the Diels-Alder (DA) reaction, a "click reaction" in the preparation of thermally amendable and self-healing polymeric materials having reactive furfuryl functionality. In this case, the DA and retro-DA (rDA) reactions were carried out between the tailor-made homo- and copolymer of furfuryl methacrylate prepared by atom-transfer radical polymerization and a bismaleimide (BM). The kinetic studies of DA and rDA reactions were carried out using Fourier transform infrared spectroscopy. The DA polymers were insoluble in toluene at room temperature. When the DA polymers were heated at 100 degrees C in toluene, it was soluble. This is because of the cleavage between furfuryl functionality and BM. The chemical cross-link density was determined by the Flory-Rehner equation. The cross-linked polymer showed much greater adhesive strength at room temperature, but the adhesive strength was quite low at higher temperature. The self-healing capability was studied by using scanning electron microscopy analysis. The thermal and dynamic mechanical properties of the thermally amendable cross-linked materials were investigated by thermogravimetric analysis and dynamic mechanical analysis.

Tailored approach to sleep health education (TASHE): study protocol for a web-based randomized controlled trial.

PubMed

Williams, Natasha J; Robbins, Rebecca; Rapoport, David; Allegrante, John P; Cohall, Alwyn; Ogedgebe, Gbenga; Jean-Louis, Girardin

2016-12-08

Obstructive sleep apnea (OSA) is a sleep disorder that disproportionately affects African Americans (hereafter referred to as blacks). Moreover, blacks may underutilize sleep services including overnight polysomnography. Thus, OSA among blacks may go undiagnosed and untreated, which has significant health consequences, including hypertension, diabetes, cognitive impairment, and daytime sleepiness. This two-arm randomized controlled trial will assign 200 participants to a culturally and linguistically tailored web-based sleep educational platform. The website will be developed to ensure that the content is user friendly and that it is readable and acceptable by the target community. Participants will receive login information to a password-protected website and will have access to the website for 2 months. Study assessments will be collected at baseline, 2 months (post-enrollment) and at 6 months (follow-up). We will use qualitative and quantitative methods to develop tailored materials and to ascertain whether tailored materials will increase OSA knowledge and OSA health literacy by comparing blacks exposed to tailored materials versus those exposed to standard sleep health literature. We hypothesize that exposure to tailored OSA information will improve OSA health literacy. Few studies have investigated the racial/ethnic disparities in relation to OSA screening and treatment comparing blacks and whites. Moreover, we know of no interventions designed to increase OSA knowledge and health literacy among blacks. Use of the Internet to disseminate health information is growing in this population. Thus, the Internet may be an effective means to increase OSA health literacy, thereby potentially increasing utilization of sleep-related services in this population. The study is registered at clinicaltrials.gov, reference number NCT02507089 . Registered on 21 July 2015.

Tailoring light-matter coupling in semiconductor and hybrid-plasmonic nanowires

PubMed Central

Piccione, Brian; Aspetti, Carlos O.; Cho, Chang-Hee; Agarwal, Ritesh

2014-01-01

Understanding interactions between light and matter is central to many fields, providing invaluable insights into the nature of matter. In its own right, a greater understanding of light-matter coupling has allowed for the creation of tailored applications, resulting in a variety of devices such as lasers, switches, sensors, modulators, and detectors. Reduction of optical mode volume is crucial to enhancing light-matter coupling strength, and among solid-state systems, self-assembled semiconductor and hybrid-plasmonic nanowires are amenable to creation of highly-confined optical modes. Following development of unique spectroscopic techniques designed for the nanowire morphology, carefully engineered semiconductor nanowire cavities have recently been tailored to enhance light-matter coupling strength in a manner previously seen in optical microcavities. Much smaller mode volumes in tailored hybrid-plasmonic nanowires have recently allowed for similar breakthroughs, resulting in sub-picosecond excited-state lifetimes and exceptionally high radiative rate enhancement. Here, we review literature on light-matter interactions in semiconductor and hybrid-plasmonic monolithic nanowire optical cavities to highlight recent progress made in tailoring light-matter coupling strengths. Beginning with a discussion of relevant concepts from optical physics, we will discuss how our knowledge of light-matter coupling has evolved with our ability to produce ever-shrinking optical mode volumes, shifting focus from bulk materials to optical microcavities, before moving on to recent results obtained from semiconducting nanowires. PMID:25093385

Room temperature synthesis of agarose/sol-gel glass pieces with tailored interconnected porosity.

PubMed

Cabañas, M V; Peña, J; Román, J; Vallet-Regí, M

2006-09-01

An original shaping technique has been applied to prepare porous bodies at room temperature. Agarose, a biodegradable polysaccharide, was added as binder of a sol-gel glass in powder form, yielding an easy to mold paste. Interconnected tailored porous bodies can be straightforwardly prepared by pouring the slurry into a polymeric scaffold, previously designed by stereolitography, which is subsequently eliminated by alkaline dissolution at room temperature. The so obtained pieces behave like a hydrogel with an enhanced consistency that makes them machinable and easy to manipulate. These materials generate an apatite-like layer when immersed in a simulated body fluid, indicating a potential in vivo bioactivity. The proposed method can be applied to different powdered materials to produce pieces, at room temperature, with various shapes and sizes and with tailored interconnected porosity.

Tailored program evaluation: Past, present, future.

PubMed

Suggs, L Suzanne; Cowdery, Joan E; Carroll, Jennifer B

2006-11-01

This paper discusses measurement issues related to the evaluation of computer-tailored health behavior change programs. As the first generation of commercially available tailored products is utilized in health promotion programming, programmers and researchers are becoming aware of the unique challenges that the evaluation of these programs presents. A project is presented that used an online tailored health behavior assessment (HBA) in a worksite setting. Process and outcome evaluation methods are described and include the challenges faced, and strategies proposed and implemented, for meeting them. Implications for future research in tailored program development, implementation, and evaluation are also discussed.

Employee Perceptions of Workplace Health Promotion Programs: Comparison of a Tailored, Semi-Tailored, and Standardized Approach

PubMed Central

Street, Tamara D.; Lacey, Sarah J.

2018-01-01

In the design of workplace health promotion programs (WHPPs), employee perceptions represent an integral variable which is predicted to translate into rate of user engagement (i.e., participation) and program loyalty. This study evaluated employee perceptions of three workplace health programs promoting nutritional consumption and physical activity. Programs included: (1) an individually tailored consultation with an exercise physiologist and dietitian; (2) a semi-tailored 12-week SMS health message program; and (3) a standardized group workshop delivered by an expert. Participating employees from a transport company completed program evaluation surveys rating the overall program, affect, and utility of: consultations (n = 19); SMS program (n = 234); and workshops (n = 86). Overall, participants’ affect and utility evaluations were positive for all programs, with the greatest satisfaction being reported in the tailored individual consultation and standardized group workshop conditions. Furthermore, mode of delivery and the physical presence of an expert health practitioner was more influential than the degree to which the information was tailored to the individual. Thus, the synergy in ratings between individually tailored consultations and standardized group workshops indicates that low-cost delivery health programs may be as appealing to employees as tailored, and comparatively high-cost, program options. PMID:29710785

Proof-of-concept switchable hydrophobic/hydrophilic patterned surfaces from thermo-mechanically tailored acrylate systems

NASA Astrophysics Data System (ADS)

Laursen, Christopher M.

A novel, proof-of-concept, switchable hydrophobic/hydrophilic structured surface targeted to assist in antifouling of materials in aqueous environments was created through the development of a multi-tiered platform. The understructure consists of a thermo-mechanically tailored acrylate based polymer patterned in a pillared array, which was then overlaid with spatially tailored hydrophobic/hydrophilic surface chemistry treatments. Development focused on the synthesis of a ternary acrylate system displaying proper thermo-mechanical behavior in submerged conditions for the understructure, creation of a sufficient soft molding technique, and methods to chemically alter water-surface wetting interactions. The final acrylate based polymer constituents were chosen based on expected low-toxicity and the ability to be photopolymerized, while the final system displayed appropriate mechanical toughness, water absorption, and material stiffness over a select temperature window. This was important as alteration in wettability characteristics relied upon a stark transition in the polymeric materials stiffness within a narrow temperature range. The material qualitatively displayed a more hydrophobic state with the pillared surface structures erect, and a more hydrophilic state with the pillars bent over.

The effect of laser pulse tailored welding of Inconel 718

NASA Technical Reports Server (NTRS)

Mccay, T. Dwayne; Mccay, Mary Helen; Sharp, C. Michael; Womack, Michael G.

1990-01-01

Pulse tailored laser welding has been applied to wrought, wrought grain grown, and cast Inconel 718 using a CO2 laser. Prior to welding, the material was characterized metallographically and the solid state transformation regions were identified using Differential Scanning Calorimetry and high temperature x-ray diffraction. Bead on plate welds (restrained and unrestrained) were then produced using a matrix of pulse duty cycles and pulsed average power. Subsequent characterization included heat affected zone width, penetration and underbead width, the presence of cracks, microfissures and porosity, fusion zone curvature, and precipitation and liquated region width. Pedigree welding on three selected processing conditions was shown by microstructural and dye penetrant analysis to produce no microfissures, a result which strongly indicates the viability of pulse tailored welding for microfissure free IN 718.

Tailoring thermal conductivity via three-dimensional porous alumina

PubMed Central

Abad, Begoña; Maiz, Jon; Ruiz-Clavijo, Alejandra; Caballero-Calero, Olga; Martin-Gonzalez, Marisol

2016-01-01

Three-dimensional anodic alumina templates (3D-AAO) are an astonishing framework with open highly ordered three-dimensional skeleton structures. Since these templates are architecturally different from conventional solids or porous templates, they teem with opportunities for engineering thermal properties. By establishing the mechanisms of heat transfer in these frameworks, we aim to create materials with tailored thermal properties. The effective thermal conductivity of an empty 3D-AAO membrane was measured. As the effective medium theory was not valid to extract the skeletal thermal conductivity of 3D-AAO, a simple 3D thermal conduction model was developed, based on a mixed series and parallel thermal resistor circuit, giving a skeletal thermal conductivity value of approximately 1.25 W·m−1·K−1, which matches the value of the ordinary AAO membranes prepared from the same acid solution. The effect of different filler materials as well as the variation of the number of transversal nanochannels and the length of the 3D-AAO membrane in the effective thermal conductivity of the composite was studied. Finally, the thermal conductivity of two 3D-AAO membranes filled with cobalt and bismuth telluride was also measured, which was in good agreement with the thermal model predictions. Therefore, this work proved this structure as a powerful approach to tailor thermal properties. PMID:27934930

Aeroelastic Tailoring via Tow Steered Composites

NASA Technical Reports Server (NTRS)

Stanford, Bret K.; Jutte, Christine V.

2014-01-01

The use of tow steered composites, where fibers follow prescribed curvilinear paths within a laminate, can improve upon existing capabilities related to aeroelastic tailoring of wing structures, though this tailoring method has received relatively little attention in the literature. This paper demonstrates the technique for both a simple cantilevered plate in low-speed flow, as well as the wing box of a full-scale high aspect ratio transport configuration. Static aeroelastic stresses and dynamic flutter boundaries are obtained for both cases. The impact of various tailoring choices upon the aeroelastic performance is quantified: curvilinear fiber steering versus straight fiber steering, certifiable versus noncertifiable stacking sequences, a single uniform laminate per wing skin versus multiple laminates, and identical upper and lower wing skins structures versus individual tailoring.

The National Shipbuilding Research Program. Proceedings of the IREAPS Technical Symposium. Paper No. 24: MAPLIS: An On-Line Materials Resource Planning System Tailored to the Shipbuilding and Offshore Industry

DTIC Science & Technology

1982-09-01

Offshore Industry U.S. DEPARTMENT OF THE NAVY CARDEROCK DIVISION, NAVAL SURFACE WARFARE CENTER Report Documentation Page Form ApprovedOMB No . 0704...INNOVATION MARINE INDUSTRY STANDARDS WELDING INDUSTRIAL ENGINEERING EDUCATION AND TRAINING THE NATIONAL SHIPBUILDING RESEARCH PROGRAM September 1982 NSRP 0009...Proceedings of the IREAPS Technical Symposium Paper No . 24: MAPLIS: An On-Line Materials Resource Planning System Tailored to the Shipbuilding and

Neonates need tailored drug formulations.

PubMed

Allegaert, Karel

2013-02-08

Drugs are very strong tools used to improve outcome in neonates. Despite this fact and in contrast to tailored perfusion equipment, incubators or ventilators for neonates, we still commonly use drug formulations initially developed for adults. We would like to make the point that drug formulations given to neonates need to be tailored for this age group. Besides the obvious need to search for active compounds that take the pathophysiology of the newborn into account, this includes the dosage and formulation. The dosage or concentration should facilitate the administration of low amounts and be flexible since clearance is lower in neonates with additional extensive between-individual variability. Formulations need to be tailored for dosage variability in the low ranges and also to the clinical characteristics of neonates. A specific focus of interest during neonatal drug development therefore is a need to quantify and limit excipient exposure based on the available knowledge of their safety or toxicity. Until such tailored vials and formulations become available, compounding practices for drug formulations in neonates should be evaluated to guarantee the correct dosing, product stability and safety.

Structural Tailoring of Advanced Turboprops (STAT). Theoretical manual

NASA Technical Reports Server (NTRS)

Brown, K. W.

1992-01-01

This manual describes the theories in the Structural Tailoring of Advanced Turboprops (STAT) computer program, which was developed to perform numerical optimizations on highly swept propfan blades. The optimization procedure seeks to minimize an objective function, defined as either direct operating cost or aeroelastic differences between a blade and its scaled model, by tuning internal and external geometry variables that must satisfy realistic blade design constraints. The STAT analyses include an aerodynamic efficiency evaluation, a finite element stress and vibration analysis, an acoustic analysis, a flutter analysis, and a once-per-revolution (1-p) forced response life prediction capability. The STAT constraints include blade stresses, blade resonances, flutter, tip displacements, and a 1-P forced response life fraction. The STAT variables include all blade internal and external geometry parameters needed to define a composite material blade. The STAT objective function is dependent upon a blade baseline definition which the user supplies to describe a current blade design for cost optimization or for the tailoring of an aeroelastic scale model.

Structural Tailoring of Advanced Turboprops (STAT). Theoretical manual

NASA Astrophysics Data System (ADS)

Brown, K. W.

1992-10-01

This manual describes the theories in the Structural Tailoring of Advanced Turboprops (STAT) computer program, which was developed to perform numerical optimizations on highly swept propfan blades. The optimization procedure seeks to minimize an objective function, defined as either direct operating cost or aeroelastic differences between a blade and its scaled model, by tuning internal and external geometry variables that must satisfy realistic blade design constraints. The STAT analyses include an aerodynamic efficiency evaluation, a finite element stress and vibration analysis, an acoustic analysis, a flutter analysis, and a once-per-revolution (1-p) forced response life prediction capability. The STAT constraints include blade stresses, blade resonances, flutter, tip displacements, and a 1-P forced response life fraction. The STAT variables include all blade internal and external geometry parameters needed to define a composite material blade. The STAT objective function is dependent upon a blade baseline definition which the user supplies to describe a current blade design for cost optimization or for the tailoring of an aeroelastic scale model.

Au-Ag-Cu nano-alloys: tailoring of permittivity

NASA Astrophysics Data System (ADS)

Hashimoto, Yoshikazu; Seniutinas, Gediminas; Balčytis, Armandas; Juodkazis, Saulius; Nishijima, Yoshiaki

2016-04-01

Precious metal alloys enables new possibilities to tailor materials for specific optical functions. Here we present a systematic study of the effects of a nanoscale alloying on the permittivity of Au-Ag-Cu metals at 38 different atomic mixing ratios. The permittivity was measured and analyzed numerically by applying the Drude model. X-ray diffraction (XRD) revealed the face centered cubic lattice of the alloys. Both, optical spectra and XRD results point towards an equivalent composition-dependent electron scattering behavior. Correlation between the fundamental structural parameters of alloys and the resulting optical properties is elucidated. Plasmonic properties of the Au-Ag-Cu alloy nanoparticles were investigated by numerical simulations. Guidelines for designing plasmonic response of nano- structures and their patterns are presented from the material science perspective.

Using tailored interventions to enhance smoking cessation among African-Americans at a community health center.

PubMed

Lipkus, I M; Lyna, P R; Rimer, B K

1999-03-01

This prospective randomized study examined the impact of three tailored intervention approaches to increase quitting rates among African-American smokers who were clients of a community health center that serves primarily low-income and indigent persons. Smokers were randomized to one of three groups: (1) health care provider prompting intervention alone, (2) health care provider prompting intervention with tailored print communications, and (3) health care provider prompting intervention with tailored print communications and tailored telephone counseling. Among the 160 smokers who completed the study, 35 (21.8%) had quit smoking at follow-up. Smokers who received the provider prompting intervention with tailored print materials were more likely to report having quit than smokers who received the provider intervention alone (32.7% vs. 13.2%, p < 0.05). Smokers who received all three intervention components were not more likely to report having quit at follow-up than those who only received the provider intervention (19.2% vs. 13.2%). Smokers who at baseline were less educated, smoked less than half a pack of cigarettes per day, had a stronger desire to quit, felt more efficacious, and had thought about quitting were more likely to report having quit at follow-up. These results provide support for continued refinement of tailored communications to aid smoking cessation among African-American smokers.

Development of culturally tailored educational brochures on HPV and pap tests for American Indian women.

PubMed

Sharpe, Patricia A; Brandt, Heather M; McCree, Donna H; Owl-Myers, Elizabeth; Taylor, Betty; Mullins, Glenda

2013-07-01

Participatory formative research guided the creation of a culturally tailored educational brochure about human papillomavirus (HPV) at an American Indian women's clinic. A review of existing educational materials and in-depth interviews were conducted. Nine steps for creating health communications messages that were patterned after National Cancer Institute guidelines guided the brochure development process. Of 95 women tested for HPV, 41% were positive, 32 (34%) agreed to the in-depth interview, and 9 agreed to the pretesting interview. Mean age was 41 years. Interviews revealed key themes concerning emotional reactions to abnormal Pap test results and HPV; need for basic information about HPV, Pap tests, and results; concerns about HPV stigma, sexual transmission, and communication with sexual partner; and the preferred source and format for HPV educational materials. A literature review revealed 12 areas of basic HPV content. A participatory process successfully engaged nursing staff and patients in creating culturally appropriate brochures for clinic use. This article provides specific steps for creating culturally tailored patient education materials.

Deformation and Thermal Properties of Energetic Materials.

DTIC Science & Technology

1980-12-01

have done some experiments in which they find that tetramethylammonium tribo- hydride (a free radical donor) causes increased reaction with ammonium ... nitrate . In order to test this hypothesis, mixtures of benzoyl peroxide and PETN were used in a series of TG experiments. Benzoyl peroxide is an...thec Lui~ycr;1 i that ;1 pol1 m\

Aerolastic tailoring and integrated wing design

NASA Technical Reports Server (NTRS)

Love, Mike H.; Bohlmann, Jon

1989-01-01

Much has been learned from the TSO optimization code over the years in determining aeroelastic tailoring's place in the integrated design process. Indeed, it has become apparent that aeroelastic tailoring is and should be deeply embedded in design. Aeroelastic tailoring can have tremendous effects on the design loads, and design loads affect every aspect of the design process. While optimization enables the evaluation of design sensitivities, valid computational simulations are required to make these sensitivities valid. Aircraft maneuvers simulated must adequately cover the plane's intended flight envelope, realistic design criteria must be included, and models among the various disciplines must be calibrated among themselves and with any hard-core (e.g., wind tunnel) data available. The information gained and benefits derived from aeroelastic tailoring provide a focal point for the various disciplines to become involved and communicate with one another to reach the best design possible.

1.9 μm superficially porous packing material with radially oriented pores and tailored pore size for ultra-fast separation of small molecules and biomolecules.

PubMed

Min, Yi; Jiang, Bo; Wu, Ci; Xia, Simin; Zhang, Xiaodan; Liang, Zhen; Zhang, Lihua; Zhang, Yukui

2014-08-22

In this work, 1.9 μm reversed-phase packing materials with superficially porous structure were prepared to achieve the rapid and high efficient separation of peptides and proteins. The silica particles were synthesized via three steps, nonporous silica particle preparation by a modified seeded growth method, mesoporous shell formation by a one pot templated dissolution and redeposition strategy, and pore size expansion via acid-refluxing. By such a method, 1.9 μm superficially porous materials with 0.18 μm shell thickness and tailored pore diameter (10 nm, 15 nm) were obtained. After pore enlargement, the formerly dense arrays of mesoporous structure changed, the radially oriented pores dominated the superficially porous structure. The chromatographic performance of such particles was investigated after C18 derivatization. For packing materials with 1.9 μm diameter and 10 nm pore size, the column efficiency could reach 211,300 plates per m for naphthalene. To achieve the high resolution separation of peptides and proteins, particles with pore diameter of 15 nm were tailored, by which the baseline separation of 5 peptides and 5 intact proteins could be respectively achieved within 1 min, demonstrating the superiority in the high efficiency and high throughput analysis of biomolecules. Furthermore, BSA digests were well separated with peak capacity of 120 in 30 min on a 15 cm-long column. Finally, we compared our columns with a 1.7 μm Kinetex C18 column under the same conditions, our particles with 10nm pore size demonstrated similar performance for separation of the large intact proteins. Moreover, the particles with 15 nm pore size showed more symmetrical peaks for the separation of large proteins (BSA, OVA and IgG) and provided rapid separation of protein extracts from Escherichia coli in 5 min. All these results indicated that the synthesized 1.9 μm superficially porous silica packing materials would be promising in the ultra-fast and high

Evaluation of Aeroelastically Tailored Small Wind Turbine Blades Final Project Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Griffin, Dayton A.

2005-09-29

Evaluation of Aeroelastically Tailored Small Wind Turbine Blades Final Report Global Energy Concepts, LLC (GEC) has performed a conceptual design study concerning aeroelastic tailoring of small wind turbine blades. The primary objectives were to evaluate ways that blade/rotor geometry could be used to enable cost-of-energy reductions by enhancing energy capture while constraining or mitigating blade costs, system loads, and related component costs. This work builds on insights developed in ongoing adaptive-blade programs but with a focus on application to small turbine systems with isotropic blade material properties and with combined blade sweep and pre-bending/pre-curving to achieve the desired twist coupling.more » Specific goals of this project are to: (A) Evaluate and quantify the extent to which rotor geometry can be used to realize load-mitigating small wind turbine rotors. Primary aspects of the load mitigation are: (1) Improved overspeed safety affected by blades twisting toward stall in response to speed increases. (2) Reduced fatigue loading affected by blade twisting toward feather in response to turbulent gusts. (B) Illustrate trade-offs and design sensitivities for this concept. (C) Provide the technical basis for small wind turbine manufacturers to evaluate this concept and commercialize if the technology appears favorable. The SolidWorks code was used to rapidly develop solid models of blade with varying shapes and material properties. Finite element analyses (FEA) were performed using the COSMOS code modeling with tip-loads and centripetal accelerations. This tool set was used to investigate the potential for aeroelastic tailoring with combined planform sweep and pre-curve. An extensive matrix of design variables was investigated, including aerodynamic design, magnitude and shape of planform sweep, magnitude and shape of blade pre-curve, material stiffness, and rotor diameter. The FEA simulations resulted in substantial insights into the

Modeling and Design Analysis Methodology for Tailoring of Aircraft Structures with Composites

NASA Technical Reports Server (NTRS)

Rehfield, Lawrence W.

2004-01-01

Composite materials provide design flexibility in that fiber placement and orientation can be specified and a variety of material forms and manufacturing processes are available. It is possible, therefore, to 'tailor' the structure to a high degree in order to meet specific design requirements in an optimum manner. Common industrial practices, however, have limited the choices designers make. One of the reasons for this is that there is a dearth of conceptual/preliminary design analysis tools specifically devoted to identifying structural concepts for composite airframe structures. Large scale finite element simulations are not suitable for such purposes. The present project has been devoted to creating modeling and design analysis methodology for use in the tailoring process of aircraft structures. Emphasis has been given to creating bend-twist elastic coupling in high aspect ratio wings or other lifting surfaces. The direction of our work was in concert with the overall NASA effort Twenty- First Century Aircraft Technology (TCAT). A multi-disciplinary team was assembled by Dr. Damodar Ambur to work on wing technology, which included our project.

Climbing therapy under PK-tailored prophylaxis.

PubMed

Stemberger, M; Schmit, E; Czepa, D; Kurnik, K; Spannagl, M

2014-01-01

Climbing has a low risk of injury and strengthens the entire musculature. Due to its benefits in physical and mental health as well as its high fun factor climbing is an established way of therapy. So far, the usefulness of climbing therapy has not been shown for people with haemophilia (PWH). A crucial requirement for physical activity in PWH is regular prophylaxis. As the patient's individual pharmacokinetic (PK) response varies significantly, PK-tailored prophylaxis may decrease bleeding frequency. We describe a man (age 25 years) with severe haemophilia A who took part in an 8.5-month weekly climbing program under PK-tailored prophylaxis. Bleeding frequency, factor consumption, joint health (Haemophilia Joint Health Score, HJHS), quality of life (Haemo-QoL-A) and climbing performance (UIAA scale) were assessed before and after the training. Prior to the study, the patient was on demand treatment. The patient was started on standard prophylaxis for a 2 months period and then observed for 6.5 months under PK-tailored prophylaxis. PK-tailored prophylaxis was targeted to a trough level of 1-3%. For high-impact activities a factor activity >15%, for low-impact activities a factor activity >5% was suggested. Climbing therapy was safe. The bleeding rate decreased from 14 (2012) to 1 (during the study period of 8.5 months). The one bleeding event was due to a missed infusion and was not triggered by physical activity. The elimination half-life using Bayesian statistics was determined to be 16h. Using this half-life for PK-tailored prophylaxis reduced the factor VIII consumption in comparison to standard prophylaxis. Joint health was particularly improved in the categories range of motion and swelling. Quality of life scores stayed at a high level. Climbing performance improved by 1 grade. The combination of PK-tailored prophylaxis with therapeutic climbing improved clinical outcome in this young adult with severe haemophilia. The tailored concept for high- and low

Tailored logistics: the next advantage.

PubMed

Fuller, J B; O'Conor, J; Rawlinson, R

1993-01-01

How many top executives have ever visited with managers who move materials from the factory to the store? How many still reduce the costs of logistics to the rent of warehouses and the fees charged by common carriers? To judge by hours of senior management attention, logistics problems do not rank high. But logistics have the potential to become the next governing element of strategy. Whether they know it or not, senior managers of every retail store and diversified manufacturing company compete in logistically distinct businesses. Customer needs vary, and companies can tailor their logistics systems to serve their customers better and more profitably. Companies do not create value for customers and sustainable advantage for themselves merely by offering varieties of goods. Rather, they offer goods in distinct ways. A particular can of Coca-Cola, for example, might be a can of Coca-Cola going to a vending machine, or a can of Coca-Cola that comes with billing services. There is a fortune buried in this distinction. The goal of logistics strategy is building distinct approaches to distinct groups of customers. The first step is organizing a cross-functional team to proceed through the following steps: segmenting customers according to purchase criteria, establishing different standards of service for different customer segments, tailoring logistics pipelines to support each segment, and creating economics of scale to determine which assets can be shared among various pipelines. The goal of establishing logistically distinct businesses is familiar: improved knowledge of customers and improved means of satisfying them.

Au-Ag-Cu nano-alloys: tailoring of permittivity

PubMed Central

Hashimoto, Yoshikazu; Seniutinas, Gediminas; Balčytis, Armandas; Juodkazis, Saulius; Nishijima, Yoshiaki

2016-01-01

Precious metal alloys enables new possibilities to tailor materials for specific optical functions. Here we present a systematic study of the effects of a nanoscale alloying on the permittivity of Au-Ag-Cu metals at 38 different atomic mixing ratios. The permittivity was measured and analyzed numerically by applying the Drude model. X-ray diffraction (XRD) revealed the face centered cubic lattice of the alloys. Both, optical spectra and XRD results point towards an equivalent composition-dependent electron scattering behavior. Correlation between the fundamental structural parameters of alloys and the resulting optical properties is elucidated. Plasmonic properties of the Au-Ag-Cu alloy nanoparticles were investigated by numerical simulations. Guidelines for designing plasmonic response of nano- structures and their patterns are presented from the material science perspective. PMID:27118459

Biological fabrication of cellulose fibers with tailored properties

NASA Astrophysics Data System (ADS)

Natalio, Filipe; Fuchs, Regina; Cohen, Sidney R.; Leitus, Gregory; Fritz-Popovski, Gerhard; Paris, Oskar; Kappl, Michael; Butt, Hans-Jürgen

2017-09-01

Cotton is a promising basis for wearable smart textiles. Current approaches that rely on fiber coatings suffer from function loss during wear. We present an approach that allows biological incorporation of exogenous molecules into cotton fibers to tailor the material’s functionality. In vitro model cultures of upland cotton (Gossypium hirsutum) are incubated with 6-carboxyfluorescein-glucose and dysprosium-1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetic acid-glucose, where the glucose moiety acts as a carrier capable of traveling from the vascular connection to the outermost cell layer of the ovule epidermis, becoming incorporated into the cellulose fibers. This yields fibers with unnatural properties such as fluorescence or magnetism. Combining biological systems with the appropriate molecular design offers numerous possibilities to grow functional composite materials and implements a material-farming concept.

Tailored ramp wave generation in gas gun experiments

NASA Astrophysics Data System (ADS)

Cotton, Matthew; Chapman, David; Winter, Ron; Harris, Ernie; Eakins, Daniel

2015-09-01

Gas guns are traditionally used as platforms to introduce a planar shock wave to a material using plate impact methods, generating states on the Hugoniot. The ability to deliver a ramp wave to a target during a gas gun experiment enables access to different regions of the equation-of-state surface, making it a valuable technique for characterising material behaviour. Previous techniques have relied on the use of multi-material impactors to generate a density gradient, which can be complex to manufacture. In this paper we describe the use of an additively manufactured steel component consisting of an array of tapered spikes which can deliver a ramp wave over ˜ 2 μs. The ability to tailor the input wave by varying the component design is discussed, an approach which makes use of the design freedom offered by additive manufacturing techniques to rapidly iterate the spike profile. Results from gas gun experiments are presented to evaluate the technique, and compared with 3D hydrodynamic simulations.

Biological fabrication of cellulose fibers with tailored properties.

PubMed

Natalio, Filipe; Fuchs, Regina; Cohen, Sidney R; Leitus, Gregory; Fritz-Popovski, Gerhard; Paris, Oskar; Kappl, Michael; Butt, Hans-Jürgen

2017-09-15

Cotton is a promising basis for wearable smart textiles. Current approaches that rely on fiber coatings suffer from function loss during wear. We present an approach that allows biological incorporation of exogenous molecules into cotton fibers to tailor the material's functionality. In vitro model cultures of upland cotton ( Gossypium hirsutum ) are incubated with 6-carboxyfluorescein-glucose and dysprosium-1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetic acid-glucose, where the glucose moiety acts as a carrier capable of traveling from the vascular connection to the outermost cell layer of the ovule epidermis, becoming incorporated into the cellulose fibers. This yields fibers with unnatural properties such as fluorescence or magnetism. Combining biological systems with the appropriate molecular design offers numerous possibilities to grow functional composite materials and implements a material-farming concept. Copyright © 2017 The Authors, some rights reserved; exclusive licensee American Association for the Advancement of Science. No claim to original U.S. Government Works.

A model of tailoring effects: A randomized controlled trial examining the mechanisms of tailoring in a web-based STD screening intervention.

PubMed

Lustria, Mia Liza A; Cortese, Juliann; Gerend, Mary A; Schmitt, Karla; Kung, Ying Mai; McLaughlin, Casey

2016-11-01

This study explores the mechanisms of tailoring within the context of RU@Risk a brief Web-based intervention designed to promote sexually transmitted disease (STD) testing among young adults. This is one of a few studies to empirically examine theorized message processing mechanisms of tailoring and persuasion outcomes in a single model. Sexually active college students (N = 1065) completed a pretest, were randomly assigned to explore a tailored or nontailored website, completed a posttest, and were offered the opportunity to order a free at-home STD test kit. As intervention effects were hypothesized to work via increases in perceived risk, change in perceived risk from pretest to posttest by condition was examined. Hypothesized mechanisms of tailoring (perceived personal relevance, attention, and elaboration) were examined using structural equation modeling (SEM). All analyses controlled for demographic variables and sexual history. As predicted, perceived risk of STDs increased from pretest to posttest, but only in the tailored condition. Results revealed that exposure to the tailored (vs. nontailored) website increased perceived personal relevance, attention to, and elaboration of the message. These effects in turn were associated with greater perceived risk of STDs and intentions to get tested. Additionally, participants in the tailored condition were more likely to order a test kit. Findings provide insight into the mechanisms of tailoring with important implications for optimizing message design. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Directly tailoring photon-electron coupling for sensitive photoconductance

NASA Astrophysics Data System (ADS)

Huang, Zhiming; Zhou, Wei; Huang, Jingguo; Wu, Jing; Gao, Yanqing; Qu, Yue; Chu, Junhao

2016-03-01

The coupling between photons and electrons is at the heart of many fundamental phenomena in nature. Despite tremendous advances in controlling electrons by photons in engineered energy-band systems, control over their coupling is still widely lacking. Here we demonstrate an unprecedented ability to couple photon-electron interactions in real space, in which the incident electromagnetic wave directly tailors energy bands of solid to generate carriers for sensitive photoconductance. By spatially coherent manipulation of metal-wrapped material system through anti-symmetric electric field of the irradiated electromagnetic wave, electrons in the metals are injected and accumulated in the induced potential well (EIW) produced in the solid. Respective positive and negative electric conductances are easily observed in n-type and p-type semiconductors into which electrons flow down from the two metallic sides under light irradiation. The photoconductivity is further confirmed by sweeping the injected electrons out of the semiconductor before recombination applied by sufficiently strong electric fields. Our work opens up new perspectives for tailoring energy bands of solids and is especially relevant to develop high effective photon detection, spin injection, and energy harvesting in optoelectronics and electronics.

Educator and Participant Perceptions and Cost Analysis of Stage-Tailored Educational Telephone Calls

ERIC Educational Resources Information Center

Esters, Onikia N.; Boeckner, Linda S.; Hubert, Melanie; Horacek, Tanya; Kritsch, Karen R.; Oakland, Mary J.; Lohse, Barbara; Greene, Geoffrey; Nitzke, Susan

2008-01-01

Objective: To identify strengths and weaknesses of nutrition education via telephone calls as part of a larger stage-of-change tailored intervention with mailed materials. Design: Evaluative feedback was elicited from educators who placed the calls and respondents who received the calls. Setting: An internet and telephone survey of 10 states in…

Tailoring protocols for chest CT applications: when and how?

PubMed Central

Iezzi, Roberto; Larici, Anna Rita; Franchi, Paola; Marano, Riccardo; Magarelli, Nicola; Posa, Alessandro; Merlino, Biagio; Manfredi, Riccardo; Colosimo, Cesare

2017-01-01

In the medical era of early detection of diseases and tailored therapies, an accurate characterization and staging of the disease is pivotal for treatment planning. The widespread use of computed tomography (CT)—often with the use of contrast material (CM)—probably represents the most important advance in diagnostic radiology. The result is a marked increase in radiation exposure of the population for medical purposes, with its intrinsic carcinogenic potential, and CM affecting kidney function. The radiologists should aim to minimize patient’s risk by reducing radiation exposure and CM amount, while maintaining the highest image quality. To achieve this goal, it is necessary to perform “patient-centric imaging”. The purpose of this review is to provide radiologists with “tips and tricks” to control radiation dose at CT, summarizing technical artifices in order to reduce image noise and increase image contrast. Also chest CT tailored protocols are supplied, with particular attention to three most common thoracic CT protocols: aortic/cardiac CT angiography (CTA), pulmonary CTA, and routine chest CT. PMID:29097345

Vertical electrostatic actuator with extended digital range via tailored topology

NASA Astrophysics Data System (ADS)

Zhang, Yanhang; Dunn, Martin L.

2002-07-01

We describe the design, fabrication, and testing of an electrostatic vertical actuator that exhibits a range of motion that covers the entire initial gap between the actuator and substrate and provides controllable digital output motion. This is obtained by spatially tailoring the electrode arrangement and the stiffness characteristics of the microstructure to control the voltage-deflection characteristics. The concept is based on the electrostatic pull down of bimaterial beams, via a series of electrodes attached to the beams by flexures with tailored stiffness characteristics. The range of travel of the actuator is defined by the post-release deformed shape of the bilayer beams, and can be controlled by a post-release heat-treat process combined with a tailored actuator topology (material distribution and geometry, including spatial geometrical patterning of the individual layers of the bilayer beams). Not only does this allow an increase in the range of travel to cover the entire initial gap, but it also permits digital control of the tip of the actuator which can be designed to yield linear displacement - pull in step characteristics. We fabricated these actuators using the MUMPs surface micromachining process, and packaged them in-house. We measured, using an interferometric microscope, full field deformed shapes of the actuator at each pull in step. The measurements compare well with companion simulation results, both qualitatively and quantitatively.

Tailor cutting of crystalline solar cells by laser micro jet

NASA Astrophysics Data System (ADS)

Bruckert, F.; Pilat, E.; Piron, P.; Torres, P.; Carron, B.; Richerzhagen, B.; Pirot, M.; Monna, R.

2012-03-01

Coupling a laser into a hair thin water micro jet (Laser Micro Jet, LMJ) for cutting applications offers a wide range of processes that are quite unique. As the laser beam is guided by internal reflections inside of a liquid cylinder, the cuts are naturally straight and do not reflect any divergence as otherwise occurs with an unguided laser beam. Furthermore, having a liquid media at the point of contact ensures a fast removal of heat and eventual debris ensuring clean cuts, which are free of any burrs. Many applications have indeed been developed for a large variety of materials, which are as different as e.g. diamond, silicon, aluminum, ceramic and hard metals. The photovoltaic industry has enjoyed in the last decades tremendous growth rates, which are still projected into the future. We focus here on the segment of Building Integrated PV (BIPV), which requests tailored solutions to actual buildings and not-one-fits-it-all standardized modules. Having the option to tailor cut solar cells opens a new field of BIPV applications. For the first time, finished crystalline solar cells have been LMJ cut into predetermined shapes. First results show that the cut is clean and neat. Preliminary solar performance measurements are positive. This opens a new avenue of tailored made modules instead of having to rely on the one-fits-alloy approach used so far.

Structural tailoring of engine blades (STAEBL) user's manual

NASA Technical Reports Server (NTRS)

Brown, K. W.

1985-01-01

This User's Manual contains instructions and demonstration case to prepare input data, run, and modify the Structural Tailoring of Engine Blades (STAEBL) computer code. STAEBL was developed to perform engine fan and compressor blade numerical optimizations. This blade optimization seeks a minimum weight or cost design that satisfies realistic blade design constraints, by tuning one to twenty design variables. The STAEBL constraint analyses include blade stresses, vibratory response, flutter, and foreign object damage. Blade design variables include airfoil thickness at several locations, blade chord, and construction variables: hole size for hollow blades, and composite material layup for composite blades.

Design of adaptive load mitigating materials usingnonlinear stress wave tailoring

DTIC Science & Technology

2016-02-24

for granular material use). 3 • Prof. Trudy Kriven (UIUC, Materials Science) is an expert in ceramic and geopolymer fabrication. • Prof. John...Figure A5.1: Schematic diagram showing the 1D chain of spherical elements in contact with (a) a uniform linear medium and (b) a composite linear...each material point to consisting of one of the given material constituents, we allow each material point to be assigned a composite material that is

Failure Analysis of Discrete Damaged Tailored Extension-Shear-Coupled Stiffened Composite Panels

NASA Technical Reports Server (NTRS)

Baker, Donald J.

2005-01-01

The results of an analytical and experimental investigation of the failure of composite is tiffener panels with extension-shear coupling are presented. This tailored concept, when used in the cover skins of a tiltrotor aircraft wing has the potential for increasing the aeroelastic stability margins and improving the aircraft productivity. The extension-shear coupling is achieved by using unbalanced 45 plies in the skin. The failure analysis of two tailored panel configurations that have the center stringer and adjacent skin severed is presented. Finite element analysis of the damaged panels was conducted using STAGS (STructural Analysis of General Shells) general purpose finite element program that includes a progressive failure capability for laminated composite structures that is based on point-stress analysis, traditional failure criteria, and ply discounting for material degradation. The progressive failure predicted the path of the failure and maximum load capability. There is less than 12 percent difference between the predicted failure load and experimental failure load. There is a good match of the panel stiffness and strength between the progressive failure analysis and the experimental results. The results indicate that the tailored concept would be feasible to use in the wing skin of a tiltrotor aircraft.

Point Defects in Oxides: Tailoring Materials Through Defect Engineering

NASA Astrophysics Data System (ADS)

Tuller, Harry L.; Bishop, Sean R.

2011-08-01

Optimization of electrical, optical, mechanical, and other properties of many advanced, functional materials today relies on precise control of point defects. This article illustrates the progress that has been made in elucidating the often complex equilibria exhibited by many materials by examining two recently well-characterized model systems, TlBr for radiation detection and PrxCe1-xO2-δ, of potential interest in solid-oxide fuel cells. The interplay between material composition, electrical conductivity, and mechanical properties (electrochemomechanics) is discussed, and implications in these relations, for example, enhancing electrical properties through large mechanical strains, are described. The impact of space charge and strain fields at interfaces, particularly important in nanostructure materials, is also emphasized. Key experimental techniques useful in characterizing bulk and surface defects are summarized and reviewed.

Optimization of current waveform tailoring for magnetically driven isentropic compression experiments

NASA Astrophysics Data System (ADS)

Waisman, E. M.; Reisman, D. B.; Stoltzfus, B. S.; Stygar, W. A.; Cuneo, M. E.; Haill, T. A.; Davis, J.-P.; Brown, J. L.; Seagle, C. T.; Spielman, R. B.

2016-06-01

The Thor pulsed power generator is being developed at Sandia National Laboratories. The design consists of up to 288 decoupled and transit time isolated capacitor-switch units, called "bricks," that can be individually triggered to achieve a high degree of pulse tailoring for magnetically driven isentropic compression experiments (ICE) [D. B. Reisman et al., Phys. Rev. Spec. Top.-Accel. Beams 18, 090401 (2015)]. The connecting transmission lines are impedance matched to the bricks, allowing the capacitor energy to be efficiently delivered to an ICE strip-line load with peak pressures of over 100 GPa. Thor will drive experiments to explore equation of state, material strength, and phase transition properties of a wide variety of materials. We present an optimization process for producing tailored current pulses, a requirement for many material studies, on the Thor generator. This technique, which is unique to the novel "current-adder" architecture used by Thor, entirely avoids the iterative use of complex circuit models to converge to the desired electrical pulse. We begin with magnetohydrodynamic simulations for a given material to determine its time dependent pressure and thus the desired strip-line load current and voltage. Because the bricks are connected to a central power flow section through transit-time isolated coaxial cables of constant impedance, the brick forward-going pulses are independent of each other. We observe that the desired equivalent forward-going current driving the pulse must be equal to the sum of the individual brick forward-going currents. We find a set of optimal brick delay times by requiring that the L2 norm of the difference between the brick-sum current and the desired forward-going current be a minimum. We describe the optimization procedure for the Thor design and show results for various materials of interest.

Optimization of current waveform tailoring for magnetically driven isentropic compression experiments.

PubMed

Waisman, E M; Reisman, D B; Stoltzfus, B S; Stygar, W A; Cuneo, M E; Haill, T A; Davis, J-P; Brown, J L; Seagle, C T; Spielman, R B

2016-06-01

The Thor pulsed power generator is being developed at Sandia National Laboratories. The design consists of up to 288 decoupled and transit time isolated capacitor-switch units, called "bricks," that can be individually triggered to achieve a high degree of pulse tailoring for magnetically driven isentropic compression experiments (ICE) [D. B. Reisman et al., Phys. Rev. Spec. Top.-Accel. Beams 18, 090401 (2015)]. The connecting transmission lines are impedance matched to the bricks, allowing the capacitor energy to be efficiently delivered to an ICE strip-line load with peak pressures of over 100 GPa. Thor will drive experiments to explore equation of state, material strength, and phase transition properties of a wide variety of materials. We present an optimization process for producing tailored current pulses, a requirement for many material studies, on the Thor generator. This technique, which is unique to the novel "current-adder" architecture used by Thor, entirely avoids the iterative use of complex circuit models to converge to the desired electrical pulse. We begin with magnetohydrodynamic simulations for a given material to determine its time dependent pressure and thus the desired strip-line load current and voltage. Because the bricks are connected to a central power flow section through transit-time isolated coaxial cables of constant impedance, the brick forward-going pulses are independent of each other. We observe that the desired equivalent forward-going current driving the pulse must be equal to the sum of the individual brick forward-going currents. We find a set of optimal brick delay times by requiring that the L2 norm of the difference between the brick-sum current and the desired forward-going current be a minimum. We describe the optimization procedure for the Thor design and show results for various materials of interest.

Optimization of current waveform tailoring for magnetically driven isentropic compression experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Waisman, E. M.; Reisman, D. B.; Stoltzfus, B. S.

2016-06-15

The Thor pulsed power generator is being developed at Sandia National Laboratories. The design consists of up to 288 decoupled and transit time isolated capacitor-switch units, called “bricks,” that can be individually triggered to achieve a high degree of pulse tailoring for magnetically driven isentropic compression experiments (ICE) [D. B. Reisman et al., Phys. Rev. Spec. Top.–Accel. Beams 18, 090401 (2015)]. The connecting transmission lines are impedance matched to the bricks, allowing the capacitor energy to be efficiently delivered to an ICE strip-line load with peak pressures of over 100 GPa. Thor will drive experiments to explore equation of state,more » material strength, and phase transition properties of a wide variety of materials. We present an optimization process for producing tailored current pulses, a requirement for many material studies, on the Thor generator. This technique, which is unique to the novel “current-adder” architecture used by Thor, entirely avoids the iterative use of complex circuit models to converge to the desired electrical pulse. We begin with magnetohydrodynamic simulations for a given material to determine its time dependent pressure and thus the desired strip-line load current and voltage. Because the bricks are connected to a central power flow section through transit-time isolated coaxial cables of constant impedance, the brick forward-going pulses are independent of each other. We observe that the desired equivalent forward-going current driving the pulse must be equal to the sum of the individual brick forward-going currents. We find a set of optimal brick delay times by requiring that the L{sub 2} norm of the difference between the brick-sum current and the desired forward-going current be a minimum. We describe the optimization procedure for the Thor design and show results for various materials of interest.« less

Tailoring nanostructured, graded, and particle-reinforced Al laminates by accumulative roll bonding.

PubMed

Göken, Mathias; Höppel, Heinz Werner

2011-06-17

Accumulative roll bonding (ARB) is a very attractive process for processing large sheets to achieve ultrafine-grained microstructure and high strength. Commercial purity Al and many Al alloys from the 5xxx and the precipitation strengthened 6xxx alloy series have been successfully processed by the ARB process into an ultrafine-grained state and superior ductility have been achieved for some materials like technical purity Al. It has also been shown that the ARB process can be successfully used to produce multi-component materials with tailored properties by reinforcement or grading, respectively. This allows optimizing the properties based on two or more materials/alloys. For example, to achieve high corrosion resistance and good visual surface properties it is interesting to produce a composite of two different Al alloys, where for example a high strength alloy of the 5xxx series is used as the core material and a 6xxx series alloy as the clad material. It has been shown that such a composite achieves more or less the same strength as the core material although 50% of the composite consists of the significant softer clad alloy. Furthermore, it has been found, that the serrated yielding which typically appears in 5xxx series alloys and limits applications as outer skin materials completely disappears. Moreover, the ARB process allows many other attractive ways to design new composites and graded material structures with unique properties by the introduction of particles, fibres and sheets. Strengthening with nanoparticles for example is a very attractive way to improve the properties and accelerate the grain refining used in the severe plastic deformation process. With an addition of only 0.1 vol.-% Al2O3 nanoparticles a significantly accelerated grain refinement has been found which reduces the number of ARB passes necessary to achieve the maximum in strength. The paper provides a short review on recent developments in the field of ARB processing for producing

Tailoring Thermal Radiative Properties with Doped-Silicon Nanowires

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Zhuomin

Aligned doped-silicon nanowire (D-SiNW) arrays form a hyperbolic metamaterial in the mid-infrared and have unique thermal radiative properties, such as broadband omnidirectional absorption, low-loss negative refraction, etc. A combined theoretical and experimental investigation will be performed to characterize D-SiNW arrays and other metamaterials for tailoring thermal radiative properties. Near-field thermal radiation between anisotropic materials with hyperbolic dispersions will also be predicted for potential application in energy harvesting. A new kind of anisotropic metamaterial with a hyperbolic dispersion in a broad infrared region has been proposed and demonstrated based on aligned doped-silicon nanowire (D-SiNW) arrays. D-SiNW-based metamaterials have unique thermal radiativemore » properties, such as broadband omnidirectional absorption whose width and location can be tuned by varying the filling ratio and/or doping level. Furthermore, high figure of merit (FOM) can be achieved in a wide spectral region, suggesting that D-SiNW arrays may be used as a negative refraction material with much less loss than other structured materials, such as layered semiconductor materials. We have also shown that D-SiNWs and other nanostructures can significantly enhance near-field thermal radiation. The study of near-field radiative heat transfer between closely spaced objects and the electromagnetic wave interactions with micro/nanostructured materials has become an emerging multidisciplinary field due to its importance in advanced energy systems, manufacturing, local thermal management, and high spatial resolution thermal sensing and mapping. We have performed extensive study on the energy streamlines involving anisotropic metamaterials and the applicability of the effective medium theory for near-field thermal radiation. Graphene as a 2D material has attracted great attention in nanoelectronics, plasmonics, and energy harvesting. We have shown that graphene can be

Tailored weight loss intervention in obese adults within primary care practice: rationale, design, and methods of Choose to Lose.

PubMed

Hartman, Sheri J; Risica, Patricia M; Gans, Kim M; Marcus, Bess H; Eaton, Charles B

2014-07-01

Although there are efficacious weight loss interventions that can improve health and delay onset of diabetes and hypertension, these interventions have not been translated into clinical practice. The primary objective of this study is to evaluate the effectiveness and cost effectiveness of a tailored lifestyle intervention in primary care patients. Patients were recruited by their primary care physicians and eligible participants were randomized to an enhanced intervention or standard intervention. All participants met with a lifestyle counselor to set calorie and physical activity goals and to discuss behavioral strategies at baseline, 6 and 12 months. During the first year, enhanced intervention participants receive monthly counseling phone calls to assist in attaining and maintaining their goals. Enhanced intervention participants also receive weekly mailings consisting of tailored and non-tailored print materials and videos focusing on weight loss, physical activity promotion and healthy eating. The second year focuses on maintenance with enhanced intervention participants receiving tailored and non-tailored print materials and videos regularly throughout the year. Standard intervention participants receive five informational handouts on weight loss across the two years. This enhanced intervention that consists of multiple modalities of print, telephone, and video with limited face-to-face counseling holds promise for being effective for encouraging weight loss, increasing physical activity and healthy eating, and also for being cost effective and generalizable for wide clinical use. This study will fill an important gap in our knowledge regarding the translation and dissemination of research from efficacy studies to best practices in clinical settings. Copyright © 2014 Elsevier Inc. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dumpala, Ravikumar; Nano Functional Materials Technology Centre, Department of Physics, Indian Institute of Technology Madras, Chennai 600036; Kumar, N.

Tribo-layer formation and frictional characteristics of the SiC ball were studied with the sliding test against nanocrystalline diamond coating under atmospheric test conditions. Unsteady friction coefficients in the range of 0.04 to 0.1 were observed during the tribo-test. Friction and wear characteristics were found to be influenced by the formation of cohesive tribo-layer (thickness ∼ 1.3 μm) in the wear track of nanocrystalline diamond coating. Hardness of the tribo-layer was measured using nanoindentation technique and low hardness of ∼ 1.2 GPa was observed. The presence of silicon and oxygen in the tribo-layer was noticed by the energy dispersive spectroscopy mappingmore » and the chemical states of the silicon were analyzed using X-ray photoelectron spectroscopy. Large amount of oxygen content in the tribo-layer indicated tribo-oxidation wear mechanism. - Highlights: • Sliding wear and friction characteristics of SiC were studied against NCD coating. • Silicon oxide tribo-layer formation was observed in the NCD coating wear track. • Low hardness 1.2 GPa of tribo-layer was measured using nanoindentation technique. • Chemical states of silicon were analyzed using X-ray photoelectron spectroscopy.« less

Tailored Codes for Small Quantum Memories

NASA Astrophysics Data System (ADS)

Robertson, Alan; Granade, Christopher; Bartlett, Stephen D.; Flammia, Steven T.

2017-12-01

We demonstrate that small quantum memories, realized via quantum error correction in multiqubit devices, can benefit substantially by choosing a quantum code that is tailored to the relevant error model of the system. For a biased noise model, with independent bit and phase flips occurring at different rates, we show that a single code greatly outperforms the well-studied Steane code across the full range of parameters of the noise model, including for unbiased noise. In fact, this tailored code performs almost optimally when compared with 10 000 randomly selected stabilizer codes of comparable experimental complexity. Tailored codes can even outperform the Steane code with realistic experimental noise, and without any increase in the experimental complexity, as we demonstrate by comparison in the observed error model in a recent seven-qubit trapped ion experiment.

Strength and Performance Enhancement of Bonded Joints by Spatial Tailoring of Adhesive Compliance via 3D Printing.

PubMed

Kumar, S; Wardle, Brian L; Arif, Muhamad F

2017-01-11

Adhesive bonding continues to emerge as a preferred route for joining materials with broad applications including advanced structures, microelectronics, biomedical systems, and consumer goods. Here, we study the mechanics of deformation and failure of tensile-loaded single-lap joints with a compliance-tailored adhesive. Tailoring of the adhesive compliance redistributes stresses and strains to reduce both shear and peel concentrations at the ends of the adhesive that determine failure of the joint. Utilizing 3D printing, the modulus of the adhesive is spatially varied along the bondlength. Experimental strength testing, including optical strain mapping, reveals that the strain redistribution results in a greater than 100% increase in strength and toughness concomitant with a 50% increase in strain-to-break while maintaining joint stiffness. The tailoring demonstrated here is immediately realizable in a broad array of 3D printing applications, and the level of performance enhancement suggests that compliance tailoring of the adhesive is a generalizable route for achieving superior performance of joints in other applications, such as advanced structural composites.

Using qualitative and quantitative formative research to develop tailored nutrition intervention materials for a diverse low-income audience.

PubMed

Strolla, Leslie O; Gans, Kim M; Risica, Patricia M

2006-08-01

More effective nutrition education to reach low-income and ethnic minority populations is needed. As part of a project to develop a tailored nutrition education intervention to meet the needs of low-income Hispanics and non-Hispanics, complementary, mixed methods of formative research were used to determine specific characteristics of the target population. The aim was to ensure that the full array of nutrition messages would be comprehensive enough to effectively tailor to the level of the individual. Barriers to healthy eating were delineated for three main dietary behaviors (number of items delineated in parentheses): lowering fat (11), increasing fruit (8) and increasing vegetables (6). Information was also collected regarding motivators for healthy eating (5), situational barriers to making healthy choices (4), other nutrition-related interests (8) and typical eating habits and food-related choices of the target audience.

Promoting a Culture of Tailoring for Systems Engineering Policy Expectations

NASA Technical Reports Server (NTRS)

Blankenship, Van A.

2016-01-01

NASA's Marshall Space Flight Center (MSFC) has developed an integrated systems engineering approach to promote a culture of tailoring for program and project policy requirements. MSFC's culture encourages and supports tailoring, with an emphasis on risk-based decision making, for enhanced affordability and efficiency. MSFC's policy structure integrates the various Agency requirements into a single, streamlined implementation approach which serves as a "one-stop-shop" for our programs and projects to follow. The engineers gain an enhanced understanding of policy and technical expectations, as well as lesson's learned from MSFC's history of spaceflight and science missions, to enable them to make appropriate, risk-based tailoring recommendations. The tailoring approach utilizes a standard methodology to classify projects into predefined levels using selected mission and programmatic scaling factors related to risk tolerance. Policy requirements are then selectively applied and tailored, with appropriate rationale, and approved by the governing authorities, to support risk-informed decisions to achieve the desired cost and schedule efficiencies. The policy is further augmented by implementation tools and lifecycle planning aids which help promote and support the cultural shift toward more tailoring. The MSFC Customization Tool is an integrated spreadsheet that ties together everything that projects need to understand, navigate, and tailor the policy. It helps them classify their project, understand the intent of the requirements, determine their tailoring approach, and document the necessary governance approvals. It also helps them plan for and conduct technical reviews throughout the lifecycle. Policy tailoring is thus established as a normal part of project execution, with the tools provided to facilitate and enable the tailoring process. MSFC's approach to changing the culture emphasizes risk-based tailoring of policy to achieve increased flexibility, efficiency

Gas Metal Arc Welding Parameters Effect on Properties of Tailored Orbital Weld of SS304 and BS1387

NASA Astrophysics Data System (ADS)

Ayof, M. N.; Hussein, N. I. S.; Noh, M. Z. Mohd

2017-09-01

Dissimilar material pipes in a power plant boiler water piping system are used to transmit water at various temperatures, either in extremely high temperature water or room temperature water. In this study, tailored orbital welding of dissimilar material of Stainless Steel (SS) 304 and British Steel (BS) 1387 were performed by Gas Metal Arc Welding (GMAW) with automated fixed nozzle-rotational jig. This study focused on GMAW parameters variation effects on mechanical properties of SS304 and BS1387 dissimilar material tailored orbital welding. The weldment quality was tested by performing non-destructive dye penetrant test. The tensile strength and microhardness were studied to verify the influence of welding parameters variations. Design of Experiment (DOE) was employed to generate process parameter using Response Surface Methodology (RSM) method. Welding parameters that were arc current, arc voltage and travel speed as input response, whilst, tensile strength and microhardness as output response. Results from non-destructive test showed no major defect occurred. The tensile strength and microhardness increased when arc current and voltage increased and travel speed decreased. Microhardness at weldment was higher than base material.

Are we there yet? An examination of online tailored health communication.

PubMed

Suggs, L Suzanne; McIntyre, Chris

2009-04-01

Increasingly, the Internet is playing an important role in consumer health and patient-provider communication. Seventy-three percent of American adults are now online, and 79% have searched for health information on the Internet. This study provides a baseline understanding of the extent to which health consumers are able to find tailored communication online. It describes the current behavioral focus, the channels being used to deliver the tailored content, and the level of tailoring in online-tailored communication. A content analysis of 497 health Web sites found few examples of personalized, targeted, or tailored health sites freely available online. Tailored content was provided in 13 Web sites, although 15 collected individual data. More health risk assessment (HRA) sites included tailored feedback than other topics. The patterns that emerged from the analysis demonstrate that online health users can access a number of Web sites with communication tailored to their needs.

Understanding tailoring in communicating about health

PubMed Central

Hawkins, Robert P.; Kreuter, Matthew; Resnicow, Kenneth; Fishbein, Martin; Dijkstra, Arie

2011-01-01

‘Tailoring’ refers to any of a number of methods for creating communications individualized for their receivers, with the expectation that this individualization will lead to larger intended effects of these communications. Results so far have been generally positive but not consistently so, and this paper seeks to explicate tailoring to help focus future research. Tailoring involves either or both of two classes of goals (enhancing cognitive preconditions for message processing and enhancing message impact through modifying behavioral determinants of goal outcomes) and employs strategies of personalization, feedback and content matching. These goals and strategies intersect in a 2 × 3 matrix in which some strategies and their component tactics match better to some goals than to others. The paper illustrates how this framework can be systematically applied in generating research questions and identifying appropriate study designs for tailoring research. PMID:18349033

Hybrid materials science: a promised land for the integrative design of multifunctional materials

NASA Astrophysics Data System (ADS)

Nicole, Lionel; Laberty-Robert, Christel; Rozes, Laurence; Sanchez, Clément

2014-05-01

For more than 5000 years, organic-inorganic composite materials created by men via skill and serendipity have been part of human culture and customs. The concept of ``hybrid organic-inorganic'' nanocomposites exploded in the second half of the 20th century with the expansion of the so-called ``chimie douce'' which led to many collaborations between a large set of chemists, physicists and biologists. Consequently, the scientific melting pot of these very different scientific communities created a new pluridisciplinary school of thought. Today, the tremendous effort of basic research performed in the last twenty years allows tailor-made multifunctional hybrid materials with perfect control over composition, structure and shape. Some of these hybrid materials have already entered the industrial market. Many tailor-made multiscale hybrids are increasingly impacting numerous fields of applications: optics, catalysis, energy, environment, nanomedicine, etc. In the present feature article, we emphasize several fundamental and applied aspects of the hybrid materials field: bioreplication, mesostructured thin films, Lego-like chemistry designed hybrid nanocomposites, and advanced hybrid materials for energy. Finally, a few commercial applications of hybrid materials will be presented.

Hybrid materials science: a promised land for the integrative design of multifunctional materials.

PubMed

Nicole, Lionel; Laberty-Robert, Christel; Rozes, Laurence; Sanchez, Clément

2014-06-21

For more than 5000 years, organic-inorganic composite materials created by men via skill and serendipity have been part of human culture and customs. The concept of "hybrid organic-inorganic" nanocomposites exploded in the second half of the 20th century with the expansion of the so-called "chimie douce" which led to many collaborations between a large set of chemists, physicists and biologists. Consequently, the scientific melting pot of these very different scientific communities created a new pluridisciplinary school of thought. Today, the tremendous effort of basic research performed in the last twenty years allows tailor-made multifunctional hybrid materials with perfect control over composition, structure and shape. Some of these hybrid materials have already entered the industrial market. Many tailor-made multiscale hybrids are increasingly impacting numerous fields of applications: optics, catalysis, energy, environment, nanomedicine, etc. In the present feature article, we emphasize several fundamental and applied aspects of the hybrid materials field: bioreplication, mesostructured thin films, Lego-like chemistry designed hybrid nanocomposites, and advanced hybrid materials for energy. Finally, a few commercial applications of hybrid materials will be presented.

Tribo-functionalizing Si and SU8 materials by surface modification for application in MEMS/NEMS actuator-based devices

NASA Astrophysics Data System (ADS)

Singh, R. A.; Satyanarayana, N.; Kustandi, T. S.; Sinha, S. K.

2011-01-01

Micro/nano-electro-mechanical-systems (MEMS/NEMS) are miniaturized devices built at micro/nanoscales. At these scales, the surface/interfacial forces are extremely strong and they adversely affect the smooth operation and the useful operating lifetimes of such devices. When these forces manifest in severe forms, they lead to material removal and thereby reduce the wear durability of the devices. In this paper, we present a simple, yet robust, two-step surface modification method to significantly enhance the tribological performance of MEMS/NEMS materials. The two-step method involves oxygen plasma treatment of polymeric films and the application of a nanolubricant, namely perfluoropolyether. We apply the two-step method to the two most important MEMS/NEMS structural materials, namely silicon and SU8 polymer. On applying surface modification to these materials, their initial coefficient of friction reduces by ~4-7 times and the steady-state coefficient of friction reduces by ~2.5-3.5 times. Simultaneously, the wear durability of both the materials increases by >1000 times. The two-step method is time effective as each of the steps takes the time duration of approximately 1 min. It is also cost effective as the oxygen plasma treatment is a part of the MEMS/NEMS fabrication process. The two-step method can be readily and easily integrated into MEMS/NEMS fabrication processes. It is anticipated that this method will work for any kind of structural material from which MEMS/NEMS are or can be made.

Tailored telephone counseling increases colorectal cancer screening.

PubMed

Rawl, Susan M; Christy, Shannon M; Monahan, Patrick O; Ding, Yan; Krier, Connie; Champion, Victoria L; Rex, Douglas

2015-08-01

To compare the efficacy of two interventions to promote colorectal cancer screening participation and forward stage movement of colorectal cancer screening adoption among first-degree relatives of individuals diagnosed with adenomatous polyps. One hundred fifty-eight first-degree relatives of individuals diagnosed with adenomatous polyps were randomly assigned to receive one of two interventions to promote colorectal cancer screening. Participants received either a tailored telephone counseling plus brochures intervention or a non-tailored print brochures intervention. Data were collected at baseline and 3 months post-baseline. Group differences and the effect of the interventions on adherence and stage movement for colorectal cancer screening were examined using t-tests, chi-square tests, and logistic regression. Individuals in the tailored telephone counseling plus brochures group were significantly more likely to complete colorectal cancer screening and to move forward on stage of change for fecal occult blood test, any colorectal cancer test stage and stage of the risk-appropriate test compared with individuals in the non-tailored brochure group at 3 months post-baseline. A tailored telephone counseling plus brochures intervention successfully promoted forward stage movement and colorectal cancer screening adherence among first-degree relatives of individuals diagnosed with adenomatous polyps. © The Author 2015. Published by Oxford University Press. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Tailored to Fit

ERIC Educational Resources Information Center

Milbradt, Allan; Klock, Ed

2006-01-01

Building a new school can be exciting and creative. The process enables parents, students, educators and the community to explore their dreams and priorities, and create a facility tailored to their unique needs. Unfortunately, the process also can leave education institutions and communities feeling like they've bought an "off-the-rack" facility…

Tailored nutrition education: is it really effective?

PubMed

Eyles, Helen; Ni Mhurchu, Cliona

2012-03-01

There has been a growing interest in tailored nutrition education over the previous decade, with a number of literature reviews suggesting this intervention strategy holds considerable potential. Nevertheless, the majority of intervention trials undertaken to date have employed subjective self-report outcome measures (such as dietary recalls). The aim of the present review is to further consider the likely true effect of tailored nutrition education by assessing the findings of tailored nutrition education intervention trials where objective outcome measures (such as sales data) have been employed. Four trials of tailored nutrition education employing objective outcome measures were identified: one was undertaken in eight low-cost supermarkets in New Zealand (2010; n 1104); one was an online intervention trial in Australia (2006; n 497); and two were undertaken in US supermarkets (1997 and 2001; n 105 and 296, respectively). Findings from the high-quality New Zealand trial were negative. Findings from the US trials were also generally negative, although reporting was poor making it difficult to assess quality. Findings from the high-quality online trial were positive, although have limited generalisability for public health. Trials employing objective outcome measures strongly suggest tailored nutrition education is not effective as a stand-alone strategy. However, further large, high-quality trials employing objective outcome measures are needed to determine the true effectiveness of this popular nutrition intervention strategy. Regardless, education plays an important role in generating social understanding and acceptance of broader interventions to improve nutrition.

Shaping electrocatalysis through tailored nanomaterials

DOE PAGES

Kang, Yijin; Yang, Peidong; Markovic, Nenad M.; ...

2016-09-21

Electrocatalysis is a subclass of heterogeneous catalysis that is aimed towards increase of the electrochemical reaction rates that are taking place at the surface of electrodes. Real-world electrocatalysts are usually based on precious metals in the form of nanoparticles due to their high surface-to-volume ratio, which enables better utilization of employed materials. Ability to tailor nanostructure of an electrocatalyst is critical in order to tune their electrocatalytic properties. Over the last decade, that has mainly been achieved through implementation of fundamental studies performed on well-defined extended surfaces with distinct single crystalline and polycrystalline structures. Based on these studies, it hasmore » been demonstrated that performance of an electrocatalyst could be significantly changed through the control of size, composition, morphology and architecture of employed nanomaterials. Here, this review outlines the following steps in the process of rational development of an efficient electrocatalyst: 1) electrochemical properties of well-defined surfaces, 2) synthesis and characterization of different classes of electrocatalysts, and 3) correlation between physical properties (size, shape, composition and morphology) and electrochemical behavior (adsorption, electrocatalytic activity and durability) of electrocatalyst. In addition, this is a brief summary of the novel research platforms in the development of functional nano materials for energy conversion and storage applications such as fuel cells electrolyzers and batteries.« less

Information Tailoring Enhancements for Large-Scale Social Data

DTIC Science & Technology

2016-06-15

Intelligent Automation Incorporated Information Tailoring Enhancements for Large-Scale... Automation Incorporated Progress Report No. 3 Information Tailoring Enhancements for Large-Scale Social Data Submitted in accordance with...1 Work Performed within This Reporting Period .................................................... 2 1.1 Enhanced Named Entity Recognition (NER

Effects of tailoring health messages on physical activity.

PubMed

Smeets, Tamara; Brug, J; de Vries, H

2008-06-01

Computer-tailored printed education can be a promising way of promoting physical activity. The present study tested whether computer-tailored feedback on physical activity is effective and whether there are differences between respondents with low and high motivation to change. Respondents (n = 487) were randomly assigned to a tailored intervention group or a no information control group. Physical activity and determinants were measured at baseline and after 3 months. At post-test, the motivated respondents in the control group were more likely not to meet the recommendation for physical activity than to meet it, and motivated respondents in the experimental group were more likely to engage in transport-related activities and showed more improvement over time for the total activity score than respondents in the control group (beta = 0.24, P = 0.02). Both groups improved their behaviour over time. No group differences in physical activity were found for the unmotivated respondents. The results showed that the effects of the tailored feedback were restricted to respondents who had a positive motivation to change at baseline. Possible explanations could be that unmotivated respondents were unwilling to read and process the information because they felt 'no need to change'. Alternatively, one tailored feedback letter may not have been sufficient for this unmotivated group.

Tailoring of EIA-649-1: Definition of Major (Class I) Engineering Change Proposal

DTIC Science & Technology

2015-05-15

MISSILE SYSTEMS CENTER TAILORING TAILORING OF EIA -649-1: DEFINITION OF MAJOR (CLASS I) ENGINEERING CHANGE PROPOSAL APPROVED FOR...PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED 1 Tailoring of EIA -649-1: Definition of Major (Class I) ECP. 1. Intent of this Tailoring Document...This tailoring document remedies a requirements gap in the industry consensus standard, EIA -649-1: 2015. Specifically, this tailoring provides a

Tailoring properties of commercially pure titanium by gradation extrusion

NASA Astrophysics Data System (ADS)

Bergmann, Markus; Rautenstrauch, Anja; Selbmann, René; de Oliveira, Raoni Barreto; Coelho, Rodrigo Santiago; Landgrebe, Dirk

2016-10-01

Commercially pure titanium (CP Ti) is of great importance in medical applications due to its attractive properties, such as high biocompatibility, excellent corrosion resistance and relatively low density and suitable stiffness. Compared to the commonly used Ti-6Al-4V alloy, its lower strength has to be increased. The most attractive approach is to subject CP Ti to severe plastic deformation (SPD) processes such as Equal Channel Angular Pressing (ECAP). The resulting decreased grain size in CP Ti yields a significant increase in hardness and strength. Common SPD-processes typically provide a uniform modification of the material. Their material efficiency and productivity are critical and limiting factors. A new approach is to tailor the material properties by using Gradation Extrusion, which produces a distinct gradient in microstructure and strength. The forming process combines a regular impact extrusion process and severe plastic deformation in the lateral area of the material. This efficient process can be integrated easily into forming process chains, for instance for dental implants. This paper presents the forming process and the applied die geometry. The results of numerical simulations are used to illustrate the potential of the process to modify and strengthen the titanium material. Experiments show that the material is successfully processed by gradation extrusion. By characterizing the hardness and its distribution within the formed parts the effects of the process are investigated.

Using Qualitative and Quantitative Formative Research to Develop Tailored Nutrition Intervention Materials for a Diverse Low-Income Audience

ERIC Educational Resources Information Center

Strolla, Leslie O.; Gans, Kim M.; Risica, Patricia M.

2006-01-01

More effective nutrition education to reach low-income and ethnic minority populations is needed. As part of a project to develop a tailored nutrition education intervention to meet the needs of low-income Hispanics and non-Hispanics, complementary, mixed methods of formative research were used to determine specific characteristics of the target…

Toward Semistructural Cellulose Nanocomposites: The Need for Scalable Processing and Interface Tailoring.

PubMed

Ansari, Farhan; Berglund, Lars A

2018-04-11

Cellulose nanocomposites can be considered for semistructural load-bearing applications where modulus and strength requirements exceed 10 GPa and 100 MPa, respectively. Such properties are higher than for most neat polymers but typical for molded short glass fiber composites. The research challenge for polymer matrix biocomposites is to develop processing concepts that allow high cellulose nanofibril (CNF) content, nanostructural control in the form of well-dispersed CNF, the use of suitable polymer matrices, as well as molecular scale interface tailoring to address moisture effects. From a practical point of view, the processing concept needs to be scalable so that large-scale industrial processing is feasible. The vast majority of cellulose nanocomposite studies elaborate on materials with low nanocellulose content. An important reason is the challenge to prevent CNF agglomeration at high CNF content. Research activities are therefore needed on concepts with the potential for rapid processing with controlled nanostructure, including well-dispersed fibrils at high CNF content so that favorable properties are obtained. This perspective discusses processing strategies, agglomeration problems, opportunities, and effects from interface tailoring. Specifically, preformed CNF mats can be used to design nanostructured biocomposites with high CNF content. Because very few composite materials combine functional and structural properties, CNF materials are an exception in this sense. The suggested processing concept could include functional components (inorganic clays, carbon nanotubes, magnetic nanoparticles, among others). In functional three-phase systems, CNF networks are combined with functional components (nanoparticles or fibril coatings) together with a ductile polymer matrix. Such materials can have functional properties (optical, magnetic, electric, etc.) in combination with mechanical performance, and the comparably low cost of nanocellulose may facilitate the

Recent advances in the design of tailored nanomaterials for efficient oxygen reduction reaction

DOE PAGES

Lv, Haifeng; Li, Dongguo; Strmcnik, Dusan; ...

2016-04-11

In the past decade, polymer electrolyte membrane fuels (PEMFCs) have been evaluated for both automotive and stationary applications. One of the main obstacles for large scale commercialization of this technology is related to the sluggish oxygen reduction reaction that takes place on the cathode side of fuel cell. Consequently, ongoing research efforts are focused on the design of cathode materials that could improve the kinetics and durability. Majority of these efforts rely on novel synthetic approaches that provide control over the structure, size, shape and composition of catalytically active materials. This article highlights the most recent advances that have beenmore » made to tailor critical parameters of the nanoscale materials in order to achieve more efficient performance of the oxygen reduction reaction (ORR).« less

Electrodynamic tailoring of self-assembled three-dimensional electrospun constructs

NASA Astrophysics Data System (ADS)

Reis, Tiago C.; Correia, Ilídio J.; Aguiar-Ricardo, Ana

2013-07-01

The rational design of three-dimensional electrospun constructs (3DECs) can lead to striking topographies and tailored shapes of electrospun materials. This new generation of materials is suppressing some of the current limitations of the usual 2D non-woven electrospun fiber mats, such as small pore sizes or only flat shaped constructs. Herein, we pursued an explanation for the self-assembly of 3DECs based on electrodynamic simulations and experimental validation. We concluded that the self-assembly process is driven by the establishment of attractive electrostatic forces between the positively charged aerial fibers and the already collected ones, which tend to acquire a negatively charged network oriented towards the nozzle. The in situ polarization degree is strengthened by higher amounts of clustered fibers, and therefore the initial high density fibrous regions are the preliminary motifs for the self-assembly mechanism. As such regions increase their in situ polarization electrostatic repulsive forces will appear, favoring a competitive growth of these self-assembled fibrous clusters. Highly polarized regions will evidence higher distances between consecutive micro-assembled fibers (MAFs). Different processing parameters - deposition time, electric field intensity, concentration of polymer solution, environmental temperature and relative humidity - were evaluated in an attempt to control material's design.The rational design of three-dimensional electrospun constructs (3DECs) can lead to striking topographies and tailored shapes of electrospun materials. This new generation of materials is suppressing some of the current limitations of the usual 2D non-woven electrospun fiber mats, such as small pore sizes or only flat shaped constructs. Herein, we pursued an explanation for the self-assembly of 3DECs based on electrodynamic simulations and experimental validation. We concluded that the self-assembly process is driven by the establishment of attractive

Web-based tailored nutrition education: results of a randomized controlled trial.

PubMed

Oenema, A; Brug, J; Lechner, L

2001-12-01

There is ample evidence that printed, computer-tailored nutrition education is a more effective tool for motivating people to change to healthier diets than general nutrition education. New technology is now providing more advanced ways of delivering tailored messages, e.g. via the World Wide Web (WWW). Before disseminating a tailored intervention via the web, it is important to investigate the potential of web-based tailored nutrition education. The present study investigated the immediate impact of web-based computer-tailored nutrition education on personal awareness and intentions related to intake of fat, fruit and vegetables. A randomized controlled trial, with a pre-test-post-test control group design was conducted. Significant differences in awareness and intention to change were found between the intervention and control group at post-test. The tailored intervention was appreciated better, was rated as more personally relevant, and had more subjective impact on opinion and intentions to change than the general nutrition information. Computer literacy had no effect on these ratings. The results indicate that interactive, web-based computer-tailored nutrition education can lead to changes in determinants of behavior. Future research should be aimed at longer-term (behavioral) effects and the practicability of distributing tailored interventions via the WWW.

Neural correlates of message tailoring and self-relatedness in smoking cessation programming.

PubMed

Chua, Hannah Faye; Liberzon, Israel; Welsh, Robert C; Strecher, Victor J

2009-01-15

Smoking leads to illnesses including addiction, cancer, and cardiovascular and respiratory diseases. Different intervention programs have become available. In the past decade, providing tailored smoking cessation messages has been shown to be more effective in inducing smoking cessation than one-size-fits-all interventions. However, little is known about the brain responses of smokers when they receive tailored smoking cessation messages. A neuroimaging study using blocked and event-related designs examined neural activity in 24 smokers exposed to high-tailored and low-tailored smoking cessation messages. In both blocked and event-related conditions, rostral medial prefrontal cortex and precuneus/posterior cingulate were engaged more during the processing of high-tailored smoking cessation messages than low-tailored smoking cessation messages. The activation patterns of smokers to tailored cessation messages show involvement of brain areas commonly implicated in self-related processing. Results seem to add support to the suggested role of self-relevance in tailored cessation programs, where previous studies have shown a potential mediating role of self-relevance on smoking abstinence. The findings are relevant to understanding the cognitive mechanisms underlying tailored message processing and might point to new directions for testing response to health communications programming.

Tailoring Magnetic Properties in Bulk Nanostructured Solids

NASA Astrophysics Data System (ADS)

Morales, Jason Rolando

Important magnetic properties and behaviors such as coercivity, remanence, susceptibility, energy product, and exchange coupling can be tailored by controlling the grain size, composition, and density of bulk magnetic materials. At nanometric length scales the grain size plays an increasingly important role since magnetic domain behavior and grain boundary concentration determine bulk magnetic behavior. This has spurred a significant amount of work devoted to developing magnetic materials with nanometric features (thickness, grain/crystallite size, inclusions or shells) in 0D (powder), 1D (wires), and 2D (thin films) materials. Large 3D nanocrystalline materials are more suitable for many applications such as permanent magnets, magneto-optical Faraday isolators etc. Yet there are relatively few successful demonstrations of 3D magnetic materials with nanoscale influenced properties available in the literature. Making dense 3D bulk materials with magnetic nanocrystalline microstructures is a challenge because many traditional densification techniques (HIP, pressureless sintering, etc.) move the microstructure out of the "nano" regime during densification. This dissertation shows that the Current Activated Pressure Assisted Densification (CAPAD) method, also known as spark plasma sintering, can be used to create dense, bulk, magnetic, nanocrystalline solids with varied compositions suited to fit many applications. The results of my research will first show important implications for the use of CAPAD for the production of exchange-coupled nanocomposite magnets. Decreases in grain size were shown to have a significant role in increasing the magnitude of exchange bias. Second, preferentially ordered bulk magnetic materials were produced with highly anisotropic material properties. The ordered microstructure resulted in changing magnetic property magnitudes (ex. change in coercivity by almost 10x) depending on the relative orientation (0° vs. 90°) of an externally

Does patient time spent viewing computer-tailored colorectal cancer screening materials predict patient-reported discussion of screening with providers?

PubMed

Sanders, Mechelle; Fiscella, Kevin; Veazie, Peter; Dolan, James G; Jerant, Anthony

2016-08-01

The main aim is to examine whether patients' viewing time on information about colorectal cancer (CRC) screening before a primary care physician (PCP) visit is associated with discussion of screening options during the visit. We analyzed data from a multi-center randomized controlled trial of a tailored interactive multimedia computer program (IMCP) to activate patients to undergo CRC screening, deployed in primary care offices immediately before a visit. We employed usage time information stored in the IMCP to examine the association of patient time spent using the program with patient-reported discussion of screening during the visit, adjusting for previous CRC screening recommendation and reading speed.On average, patients spent 33 minutes on the program. In adjusted analyses, 30 minutes spent using the program was associated with a 41% increase in the odds of the patient having a discussion with their PCP (1.04, 1.59, 95% CI). In a separate analysis of the tailoring modules; the modules encouraging adherence to the tailored screening recommendation and discussion with the patient's PCP yielded significant results. Other predictors of screening discussion included better self-reported physical health and increased patient activation. Time spent on the program predicted greater patient-physician discussion of screening during a linked visit.Usage time information gathered automatically by IMCPs offers promise for objectively assessing patient engagement around a topic and predicting likelihood of discussion between patients and their clinician. © The Author 2016. Published by Oxford University Press. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Understanding the tissue effects of tribo-corrosion: uptake, distribution, and speciation of cobalt and chromium in human bone cells.

PubMed

Shah, Karan M; Quinn, Paul D; Gartland, Alison; Wilkinson, J Mark

2015-01-01

Cobalt and chromium species are released in the local tissues as a result of tribo-corrosion, and affect bone cell survival and function. However we have little understanding of the mechanisms of cellular entry, intracellular distribution, and speciation of the metals that result in impaired bone health. Here we used synchrotron based X-ray fluorescence (XRF), X-ray absorption spectroscopy (XAS), and fluorescent-probing approaches of candidate receptors P2X7R and divalent metal transporter-1 (DMT-1), to better understand the entry, intra-cellular distribution and speciation of cobalt (Co) and chromium (Cr) in human osteoblasts and primary human osteoclasts. We found that both Co and Cr were most highly localized at nuclear and perinuclear sites in osteoblasts, suggesting uptake through cell membrane transporters, and supported by a finding that P2X7 receptor blockade reduced cellular entry of Co. In contrast, metal species were present at discrete sites corresponding to the basolateral membrane in osteoclasts, suggesting cell entry by endocytosis and trafficking through a functional secretory domain. An intracellular reduction of Cr6+ to Cr3+ was the only redox change observed in cells treated with Co2+, Cr3+, and Cr6+. Our data suggest that the cellular uptake and processing of Co and Cr differs between osteoblasts and osteoclasts. © 2014 The Authors. Journal of Orthopaedic Research published by Wiley Periodicals, Inc. on behalf of the Orthopaedic Research Society.

Microfluidic Foaming: A Powerful Tool for Tailoring the Morphological and Permeability Properties of Sponge-like Biopolymeric Scaffolds.

PubMed

Costantini, Marco; Colosi, Cristina; Jaroszewicz, Jakub; Tosato, Alessia; Święszkowski, Wojciech; Dentini, Mariella; Garstecki, Piotr; Barbetta, Andrea

2015-10-28

Ordered porous polymeric materials can be engineered to present highly ordered pore arrays and uniform and tunable pore size. These features prompted a number of applications in tissue engineering, generation of meta materials, and separation and purification of biomolecules and cells. Designing new and efficient vistas for the generation of ordered porous materials is an active area of research. Here we investigate the potential of microfluidic foaming within a flow-focusing (FF) geometry in producing 3D regular sponge-like polymeric matrices with tailored morphological and permeability properties. The challenge in using microfluidic systems for the generation of polymeric foams is in the high viscosity of the continuous phase. We demonstrate that as the viscosity of the aqueous solution increases, the accessible range of foam bubble fraction (Φb) and bubble diameter (Db) inside the microfluidic chip tend to narrow progressively. This effect limits the accessible range of geometric properties of the resulting materials. We further show that this problem can be rationally tackled by appropriate choice of the concentration of the polymer. We demonstrate that via such optimization, the microfluidic assisted synthesis of porous materials becomes a facile and versatile tool for generation of porous materials with a wide range of pore size and pore volume. Moreover, we demonstrate that the size of interconnects among pores-for a given value of the gas fraction-can be tailored through the variation of surfactant concentration. This, in turn, affects the permeability of the materials, a factor of key importance in flow-through applications and in tissue engineering.

Neural correlates of message tailoring and self-relatedness in smoking cessation programming

PubMed Central

Chua, Hannah Faye; Liberzon, Israel; Welsh, Robert C.; Strecher, Victor J.

2011-01-01

BACKGROUND Smoking leads to illnesses including addiction, cancer, and cardiovascular and respiratory diseases. Different intervention programs have become available. In the past decade, providing tailored smoking cessation messages has been shown to be more effective in inducing smoking cessation than one-size-fits-all interventions. However, little is known about the brain responses of smokers when they receive tailored smoking cessation messages. METHODS A neuroimaging study using blocked and event-related designs examined neural activity in 24 smokers exposed to high-tailored and low-tailored smoking cessation messages. RESULTS: In both blocked and event-related conditions, rostral medial prefrontal cortex and precuneus/posterior cingulate were engaged more during the processing of high-tailored smoking cessation messages than low-tailored smoking cessation messages. CONCLUSION The activation patterns of smokers to tailored cessation messages show involvement of brain areas commonly implicated in self-related processing. Results seem to add support to the suggested role of self-relevance in tailored cessation programs, where previous studies have shown a potential mediating role of self-relevance on smoking abstinence. The findings are relevant to understanding the cognitive mechanisms underlying tailored message processing and may point to new directions for testing response to health communications programming. PMID:18926523

A Taguchi study of the aeroelastic tailoring design process

NASA Technical Reports Server (NTRS)

Bohlmann, Jonathan D.; Scott, Robert C.

1991-01-01

A Taguchi study was performed to determine the important players in the aeroelastic tailoring design process and to find the best composition of the optimization's objective function. The Wing Aeroelastic Synthesis Procedure (TSO) was used to ascertain the effects that factors such as composite laminate constraints, roll effectiveness constraints, and built-in wing twist and camber have on the optimum, aeroelastically tailored wing skin design. The results show the Taguchi method to be a viable engineering tool for computational inquiries, and provide some valuable lessons about the practice of aeroelastic tailoring.

The impact of tailored self-help smoking cessation guides on young mothers.

PubMed

Davis, S W; Cummings, K M; Rimer, B K; Sciandra, R; Stone, J C

1992-01-01

It has been suggested that tailoring self-help materials for specific target populations will increase their effectiveness. This study tested the value of a self-help guide tailored specifically for women with young children. These women were recruited through a media campaign that encouraged smokers to call the Cancer Information Service (CIS) for assistance in stopping smoking. Women smokers with young children (under the age of 6) who called the CIS were given telephone counseling on quitting and were mailed one of three stop smoking guides. One third of callers received Quitting Times, a guide written specifically for women with young children; one third received the American Lung Association guide, Freedom from Smoking for You and Your Family; and one third received Clearing the Air, a guide developed by the National Cancer Institute. Six months after calling the CIS, these women were contacted by telephone to assess changes in smoking behavior. Overall, 12.5% of the women reported not smoking for at least 1 week at the time of the 6-month follow-up interview. There were no significant differences between subjects in the three groups in use of the self-help guides, methods used to attempt quitting, and quitting behavior. Findings from this study do not support the hypothesis that using a tailored stop smoking guide increases the targeted audience's cessation rate or affects quitting-related behavior. However, it should be noted that the smokers who called were predominantly in the contemplation or action stages.

Substrate-biasing during plasma-assisted atomic layer deposition to tailor metal-oxide thin film growth

DOE Office of Scientific and Technical Information (OSTI.GOV)

Profijt, H. B.; Sanden, M. C. M. van de; Kessels, W. M. M.

2013-01-15

Two substrate-biasing techniques, i.e., substrate-tuned biasing and RF biasing, have been implemented in a remote plasma configuration, enabling control of the ion energy during plasma-assisted atomic layer deposition (ALD). With both techniques, substrate bias voltages up to -200 V have been reached, which allowed for ion energies up to 272 eV. Besides the bias voltage, the ion energy and the ion flux, also the electron temperature, the electron density, and the optical emission of the plasma have been measured. The effects of substrate biasing during plasma-assisted ALD have been investigated for Al{sub 2}O{sub 3}, Co{sub 3}O{sub 4}, and TiO{sub 2}more » thin films. The growth per cycle, the mass density, and the crystallinity have been investigated, and it was found that these process and material properties can be tailored using substrate biasing. Additionally, the residual stress in substrates coated with Al{sub 2}O{sub 3} films varied with the substrate bias voltage. The results reported in this article demonstrate that substrate biasing is a promising technique to tailor the material properties of thin films synthesized by plasma-assisted ALD.« less

Does Patient Time Spent Viewing Computer-Tailored Colorectal Cancer Screening Materials Predict Patient-Reported Discussion of Screening with Providers?

ERIC Educational Resources Information Center

Sanders, Mechelle; Fiscella, Kevin; Veazie, Peter; Dolan, James G.; Jerant, Anthony

2016-01-01

The main aim is to examine whether patients' viewing time on information about colorectal cancer (CRC) screening before a primary care physician (PCP) visit is associated with discussion of screening options during the visit. We analyzed data from a multi-center randomized controlled trial of a tailored interactive multimedia computer program…

Development of Tailorable Electrically Conductive Thermal Control Material Systems

NASA Technical Reports Server (NTRS)

Deshpande, M. S.; Harada, Y.

1997-01-01

The optical characteristics of surfaces on spacecraft are fundamental parameters in controlling its temperature. Passive thermal control coatings with designed solar absorptance and infrared emittance properties have been developed and have been in use for some time. In this total space environment, the coating must be stable and maintain its desired optical properties as well as mechanical properties for the course of the mission lifetime. The mission lifetimes are increasing and in our quest to save weight, newer substrates are being integrated which limit electrical grounding schemes. All of this has added to already existing concerns about spacecraft charging and related spacecraft failures or operational failures. The concern is even greater for thermal control surfaces that are very large. One way of alleviating such concerns is to design new thermal control material systems (TCMS) that can help to mitigate charging via providing charge leakage paths. The objective of this program was to develop two types of passive electrically conductive TCMS. The first was a highly absorbing/emitting black surface and the second was a low (alpha(sub s)/epsilon(sub N)) type white surface. The surface resistance goals for the black absorber was 10(exp 4) to 10(exp 9) Omega/square, and for the white surfaces it was 10(exp 6) to 10(exp 10) Omega/square. Several material system concepts were suggested and evaluated for space environment stability and electrical performance characterization. Our efforts in designing and evaluating these material systems have resulted in several developments. New concepts, pigments and binders have been developed to provide new engineering quality TCMS. Some of these have already found application on space hardware, some are waiting to be recognized by thermal designers, and some require further detailed studies to become state-of-the-art for future space hardware and space structures. Our studies on baseline state-of-the-art materials and

Molecular dynamics simulation studies of tailored nanostructured polymers

NASA Astrophysics Data System (ADS)

Liu, Lixin

With recent advancements in the synthesis and characterization of polymeric materials, scientists are able to create multi-scale novel polymers with various cases of chemical functionalities, diversified topologies, as well as cross-linking networks. Due to those remarkable achievements, there are a broad range of possible applications of smart polymers in catalysis, in environmental remediation, and especially in drug-delivery. Because of rising interest in developing therapeutic drug binding to specific treating target, polymer chemists are in particular interests in design and engineering the drug delivery materials to be not only bio-compatible, but also to be capable of self-assembly at various in-vivo physiological stimulus. Both experimental and theoretical work indicate that the thermodynamic properties relating to the hydrophobic effect play an important role in determining self-assembly process. At the same time, computational simulation and modeling are powerful instruments to contribute to microscopic thermodynamics' understanding toward self-assembly phenomenon. Along with statistical approaches, constructing empirical model based on simulation results would also help predict for further development of tailored nano-structured materials. My Research mainly focused on investigating physical and chemical characteristics of polymer materials through molecular dynamics simulation and probing the fundamental thermodynamic driving force of self-assembly behavior. We tried to surmount technological obstacles in computational chemistry and build an efficient scheme to identify the physical and chemical Feature of molecules, to reproduce underlying properties, to understand the origin of thermodynamic signatures, and to speed up current trial and error process in screening new materials.

'What do patients want?' Tailoring medicines information to meet patients' needs.

PubMed

Young, Amber; Tordoff, June; Smith, Alesha

2017-11-01

Medicines information leaflets can equip patients to be in control of their own healthcare and support the safe and effective use of medicines. The design and content of leaflets influences patients' willingness to read them, and poor examples can cause patient confusion and anxiety. Researchers examined the literature over the past 8 years to determine the content and design of medicine information leaflets that patients prefer in order to read, understand, and use them effectively. It was found that existing leaflets do not meet patients' needs and appear ineffective. Leaflets lack the information patients seek and may contain non-essential material, affecting patients' perception of, and willingness to read them. Additionally, the acceptable leaflet length varies between patients. Application of good design principles improves readability, comprehension, and ability to locate information. Medicine information leaflets must meet patients' needs and be well designed. Tailoring information leaflets to patient characteristics and requirements would enhance effectiveness. Passive provision of pre-printed leaflets is outdated, unvalued and ineffective. Using automated computer systems for leaflet tailoring with the ability to further adapt patients' information might be the best way forward. Copyright © 2016 Elsevier Inc. All rights reserved.

Context, confidentiality, and consent in tailored health communications: a cautionary note.

PubMed

Orleans, C T

1999-01-01

This article highlights key contextual factors that emerge when the evolution of tailored health communications is viewed against the backdrop of dynamic changes in the nation's health care system--including the shift from fee-for-service medicine to managed care and the proliferation of direct-to-consumer and tailored marketing strategies in the pharmaceutical industry. It focuses on contextual variables with potential to significantly mediate the impact of personally tailored health advice--including those related to confidentiality, privacy, and informed consent and to the perceived aims, intents, and sources of tailored health messages. To protect the future of tailored health messages, more research attention must be given to defining these contextual factors and understanding the roles that they play and the ways in which they can be controlled to assure the best outcomes. Such research could point the way towards a set of empirical and ethical "best practices" based on a scientific understanding of how to maximize the benefits, and minimize the potential harms, of the widescale use of tailored health communications.

Aerogel Blanket Insulation Materials for Cryogenic Applications

NASA Technical Reports Server (NTRS)

Coffman, B. E.; Fesmire, J. E.; White, S.; Gould, G.; Augustynowicz, S.

2009-01-01

Aerogel blanket materials for use in thermal insulation systems are now commercially available and implemented by industry. Prototype aerogel blanket materials were presented at the Cryogenic Engineering Conference in 1997 and by 2004 had progressed to full commercial production by Aspen Aerogels. Today, this new technology material is providing superior energy efficiencies and enabling new design approaches for more cost effective cryogenic systems. Aerogel processing technology and methods are continuing to improve, offering a tailor-able array of product formulations for many different thermal and environmental requirements. Many different varieties and combinations of aerogel blankets have been characterized using insulation test cryostats at the Cryogenics Test Laboratory of NASA Kennedy Space Center. Detailed thermal conductivity data for a select group of materials are presented for engineering use. Heat transfer evaluations for the entire vacuum pressure range, including ambient conditions, are given. Examples of current cryogenic applications of aerogel blanket insulation are also given. KEYWORDS: Cryogenic tanks, thermal insulation, composite materials, aerogel, thermal conductivity, liquid nitrogen boil-off

eHealth and the use of individually tailored information: A systematic review.

PubMed

Conway, Nicholas; Webster, Clare; Smith, Blair; Wake, Deborah

2017-09-01

Tailored messages are those that specifically target individuals following an assessment of their unique characteristics. This systematic review assesses the evidence regarding the effectiveness of tailoring within eHealth interventions aimed at chronic disease management. OVID Medline/Embase databases were searched for randomised control trials, controlled clinical, trials, before -after studies, and time series analyses from inception - May 2014. Objectively measured clinical processes/outcomes were considered. Twenty-two papers were eligible for inclusion: 6/22 used fully tailored messaging and 16/22 used partially tailored messages. Two studies isolated tailoring as the active component. The remainder compared intervention with standard care. In all, 12/16 studies measuring clinical processes and 2/6 studies reporting clinical outcomes showed improvements, regardless of target group. Study quality was low and design did not allow for identification of interventions' active component. Heterogeneity precluded meta-analysis. This review has demonstrated that there is a lack of evidence to suggest that tailoring within an eHealth context confers benefit over non-tailored eHealth interventions.

Tailoring the mechanical and biodegradable properties of binary blends of biomedical thermoplastic elastomer.

PubMed

Ang, Hui Ying; Chan, Jingni; Toong, Daniel; Venkatraman, Subbu S; Chia, Sing Joo; Huang, Ying Ying

2018-03-01

Blending polymers with complementary properties capitalizes on the inherent advantages of both components, making it possible to tailor the behaviour of the resultant material. A polymer blend consisting of an elastomer and thermoplastic can help to improve the mechanical integrity of the system without compromising on its processibility. A series of blends of biodegradable Poly(L-lactide-co-ɛ-caprolactone) (PLC) and Poly-(l,l-lactide-co-glycolic acid) (PLLGA), and PLC with Poly-(d,l-lactide-co-glycolic acid) (PDLLGA) were evaluated as a potential material for a biodegradable vesicourethral connector device. Based on the Tg of the blends, PLC/PLLGA formed an immiscible mixture while PLC/PDLLGA resulted in a compatible blend. The results showed that with the blending of PLC, the failure mode of PLLGA and PDLLGA changed from brittle to ductile fracture, with an significant decreas in tensile modulus and strength. SEM images demonstrated the different blend morphologies of different compositions during degradation. Gel Permeation Chromatography (GPC) and mechanical characterization revealed the degradation behaviour of the blends in this order (fastest to slowest): PDLLGA and PLC/PDLLGA blends > PLLGA and PLC/PLLGA blends > PLC. The PLC/PLLGA (70:30) blend was recommended as a suitable for the vesicourethral connector device application, highlighting the tailoring of blends to achieve a desired mechanical performance. Copyright © 2017 Elsevier Ltd. All rights reserved.

Walking Works Wonders: a tailored workplace intervention evaluated over 24 months.

PubMed

Haslam, Cheryl; Kazi, Aadil; Duncan, Myanna; Clemes, Stacy; Twumasi, Ricardo

2018-06-22

This article presents longitudinal data from 1120 participants across 10 worksites enrolled in Walking Works Wonders, a tailored intervention designed to increase physical activity and reduce sedentary behaviour. The intervention was evaluated over 2 years, using a quasi-experimental design comprising 3 conditions: tailored information; standard information and control. This study explored the impact of the intervention on objective measures (BMI, %Fat, waist circumference, blood pressure and heart rate) and self-reported measures of physical activity, sedentary behaviour, physical and psychological health. Interventions tailored to employees' stage of change significantly reduced BMI and waist circumference compared to standard and control conditions. Employees who received either a standard or tailored intervention demonstrated significantly higher work ability, organizational commitment, job motivation, job satisfaction, and a reduction in intention to quit the organization. The results suggest that adopting a tailored approach to interventions.

Metal flow of a tailor-welded blank in deep drawing process

NASA Astrophysics Data System (ADS)

Yan, Qi; Guo, Ruiquan

2005-01-01

Tailor welded blanks were used in the automotive industry to consolidate parts, reduce weight, and increase safety. In recent years, this technology was developing rapidly in China. In Chinese car models, tailor welded blanks had been applied in a lot of automobile parts such as rail, door inner, bumper, floor panel, etc. Concerns on the properties of tailor welded blanks had become more and more important for automobile industry. A lot of research had shown that the strength of the welded seam was higher than that of the base metal, such that the weld failure in the aspect of strength was not a critical issue. However, formability of tailor welded blanks in the stamping process was complex. Among them, the metal flow of tailor welded blanks in the stamping process must be investigated thoroughly in order to reduce the scrap rate during the stamping process in automobile factories. In this paper, the behavior of metal flow for tailor welded blanks made by the laser welding process with two types of different thickness combinations were studied in the deep drawing process. Simulations and experiment verification of the movement of weld line for tailor welded blanks were discussed in detail. Results showed that the control on the movement of welded seam during stamping process by taking some measures in the aspect of blank holder was effective.

Sol-gel Technology and Advanced Electrochemical Energy Storage Materials

NASA Technical Reports Server (NTRS)

Chu, Chung-tse; Zheng, Haixing

1996-01-01

Advanced materials play an important role in the development of electrochemical energy devices such as batteries, fuel cells, and electrochemical capacitors. The sol-gel process is a versatile solution for use in the fabrication of ceramic materials with tailored stoichiometry, microstructure, and properties. This processing technique is particularly useful in producing porous materials with high surface area and low density, two of the most desirable characteristics for electrode materials. In addition,the porous surface of gels can be modified chemically to create tailored surface properties, and inorganic/organic micro-composites can be prepared for improved material performance device fabrication. Applications of several sol-gel derived electrode materials in different energy storage devices are illustrated in this paper. V2O5 gels are shown to be a promising cathode material for solid state lithium batteries. Carbon aerogels, amorphous RuO2 gels and sol-gel derived hafnium compounds have been studied as electrode materials for high energy density and high power density electrochemical capacitors.

A tribo-mechanical analysis of PVA-based building-blocks for implementation in a 2-layered skin model.

PubMed

Morales Hurtado, M; de Vries, E G; Zeng, X; van der Heide, E

2016-09-01

Poly(vinyl) alcohol hydrogel (PVA) is a well-known polymer widely used in the medical field due to its biocompatibility properties and easy manufacturing. In this work, the tribo-mechanical properties of PVA-based blocks are studied to evaluate their suitability as a part of a structure simulating the length scale dependence of human skin. Thus, blocks of pure PVA and PVA mixed with Cellulose (PVA-Cel) were synthesised via freezing/thawing cycles and their mechanical properties were determined by Dynamic Mechanical Analysis (DMA) and creep tests. The dynamic tests addressed to elastic moduli between 38 and 50kPa for the PVA and PVA-Cel, respectively. The fitting of the creep compliance tests in the SLS model confirmed the viscoelastic behaviour of the samples with retardation times of 23 and 16 seconds for the PVA and PVA-Cel, respectively. Micro indentation tests were also achieved and the results indicated elastic moduli in the same range of the dynamic tests. Specifically, values between 45-55 and 56-81kPa were obtained for the PVA and PVA-Cel samples, respectively. The tribological results indicated values of 0.55 at low forces for the PVA decreasing to 0.13 at higher forces. The PVA-Cel blocks showed lower friction even at low forces with values between 0.2 and 0.07. The implementation of these building blocks in the design of a 2-layered skin model (2LSM) is also presented in this work. The 2LSM was stamped with four different textures and their surface properties were evaluated. The hydration of the 2LSM was also evaluated with a corneometer and the results indicated a gradient of hydration comparable to the human skin. Copyright © 2016 Elsevier Ltd. All rights reserved.

A comparative study of tribological characteristics of hydrogenated DLC film sliding against ceramic mating materials for helium applications

NASA Astrophysics Data System (ADS)

Wu, Daheng; Ren, Siming; Pu, Jibin; Lu, Zhibin; Zhang, Guangan; Wang, Liping

2018-05-01

The tribological behaviors of hydrogenated DLC film sliding against Al2O3, ZrO2, Si3N4 and WC mating balls have been comparatively investigated by a ball-on-disk tribometer at 150 °C under helium and air (RH = 6%) conditions. The results showed that the mating material influenced the friction and wear behavior remarkably in helium atmosphere, where the wear rates were in inversely proportional to the friction coefficients (COF) of those tribo-pairs. Compared to the tests in helium, the tribological performance of DLC film significantly improved in air. Scanning electron microscope (SEM) and Raman spectroscopy were performed to study the friction behavior and wear mechanism of the film under different conditions. It suggested that the severe abrasion was caused by the strong interaction between the tribo-pairs in helium atmosphere at 150 °C, whereas the sufficient passivation of the dangling bonds of carbon atoms at sliding interface by chemically active molecules, such as water and oxygen, dominated the ultralow friction under air condition. Meanwhile, Hertz analysis was used to further elucidate the frictional mechanism of DLC film under helium and air conditions. It showed that the coefficient of friction was consistent with the varied tendency of the contact radius, namely, higher friction coefficient corresponded to the larger contact radius, which was the same with the relationship between the wear rate and the contact pressure. All of the results made better understanding of the essential mechanism of hydrogenated DLC film sliding against different pairs, which were able to guide the further application of DLC film in the industrial fields of helium atmosphere.

Spray Characteristics and Tribo-Mechanical Properties of High-Velocity Arc-Sprayed WC-W2C Iron-Based Coatings

NASA Astrophysics Data System (ADS)

Tillmann, W.; Hagen, L.; Kokalj, D.

2017-10-01

In terms of arc-sprayed coatings, the lamellar coating microstructure is mainly affected by the atomization behavior of the molten electrode tips. When using compressed air, oxide formations occur during atomization, across the particle-laden spray plume and when the molten droplets splash onto the substrate. Within the scope of this study, the potential of a high-velocity arc-spraying process due to elevated atomization gas pressures and its effect on the spray and coating characteristics was analyzed using a cast tungsten carbide (CTC)-reinforced FeCMnSi cored wire. Since the atomization behavior corresponds with the electrode phenomena, the power spectrum and the droplet formation were observed during spraying. The tribo-mechanical properties of CTC-FeCMnSi coatings were examined in dry sliding experiments and indentation tests. In addition, adhesion tests and metallographic investigations were carried out to analyze the bonding strength, cohesive behavior, and lamellar microstructure. The occurrence of oxide phases was evaluated by x-ray diffraction and electron microscopy. Moreover, the oxygen content was determined by using glow discharge optical emission spectroscopy as well as energy-dispersive x-ray spectroscopy. With respect to elevated atomization gas pressures, a dense microstructure with improved adhesion to the substrate and reduced surface roughness was observed. Dry sliding experiments revealed an advanced wear behavior of specimens, when using above average increased atomization gas pressures. Analytic methods verified the existence of oxide phases, which were generated during spraying. A significant change of the extent and type of oxides, when applying an increased flow rate of the atomization gas, cannot be observed. Besides an enhanced coating quality, the use of increased atomization gas pressure exhibited good process stability.

Tailoring the Crystal Structure Toward Optimal Super Conductors

DTIC Science & Technology

2016-06-23

AFRL-AFOSR-VA-TR-2016-0210 TAILORING THE CRYSTAL STRUCTURE TOWARD OPTIMAL SUPERCONDUCTORS Emilia Morosan WILLIAM MARSH RICE UNIV HOUSTON TX Final...TAILORING THE CRYSTAL STRUCTURE TOWARD OPTIMAL SUPERCONDUCTORS 5a. CONTRACT NUMBER FA9550-11-1-0023 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6...studied the properties of layered transition metal compounds in search of unconventional superconductors . The aim is to identify ground states competing

The Effects of Tailoring Knowledge Acquisition on Colorectal Cancer Screening Self-Efficacy

PubMed Central

Jerant, Anthony; To, Patricia; Franks, Peter

2015-01-01

Interventions tailored to psychological factors such as personal and vicarious behavioral experiences can enhance behavioral self-efficacy, but are complex to develop and implement. Information seeking theory suggests tailoring acquisition of health knowledge (without concurrent psychological factor tailoring) could enhance self-efficacy, simplifying the design of tailored behavior change interventions. To begin to examine this issue, the authors conducted exploratory analyses of data from a randomized controlled trial, comparing the effects of an experimental colorectal cancer (CRC) screening intervention tailoring knowledge acquisition with the effects of a non-tailored control on CRC screening knowledge and self-efficacy in 1159 patients comprising three ethnicity/language strata (Hispanic/Spanish 23.4%, Hispanic/English 27.2%, non-Hispanic/English 49.3%) and five recruitment center strata. Adjusted for study strata, the mean post-intervention knowledge score was significantly higher in the experimental group versus control. Adjusted experimental intervention exposure (B = 0.22, 95% CI [0.14, 0.30]), pre-intervention knowledge (B = 0.11, 95% CI [0.05, 0.16]), and post-intervention knowledge (B = 0.03, 95% CI [0.01, 0.05]) were independently associated with subsequent CRC screening self-efficacy (p < .001 all associations). These exploratory findings suggest tailoring knowledge acquisition may enhance self-efficacy, with potential implications for tailored intervention design, but require confirmation in studies specifically designed to examine this issue. PMID:25928315

Tailored Mesoporous Silicas: From Confinement Effects to Catalysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buchanan III, A C; Kidder, Michelle

2010-01-01

Ordered mesoporous silicas continue to find widespread use as supports for diverse applications such as catalysis, separations, and sensors. They provide a versatile platform for these studies because of their high surface area and the ability to control pore size, topology, and surface properties over wide ranges. Furthermore, there is a diverse array of synthetic methodologies for tailoring the pore surface with organic, organometallic, and inorganic functional groups. In this paper, we will discuss two examples of tailored mesoporous silicas and the resultant impact on chemical reactivity. First, we explore the impact of pore confinement on the thermochemical reactivity ofmore » phenethyl phenyl ether (PhCH2CH2OPh, PPE), which is a model of the dominant {beta}-aryl ether linkage present in lignin derived from woody biomass. The influence of PPE surface immobilization, grafting density, silica pore diameter, and presence of a second surface-grafted inert 'spacer' molecule on the product selectivity has been examined. We will show that the product selectivity can be substantially altered compared with the inherent gas-phase selectivity. Second, we have recently initiated an investigation of mesoporous silica supported, heterobimetallic oxide materials for photocatalytic conversion of carbon dioxide. Through surface organometallic chemistry, isolated M-O-M species can be generated on mesoporous silicas that, upon irradiation, form metal to metal charge transfer bands capable of converting CO{sub 2} into CO. Initial results from studies of Ti(IV)-O-Sn(II) on SBA-15 will be presented.« less

Comparing homeless persons' care experiences in tailored versus nontailored primary care programs.

PubMed

Kertesz, Stefan G; Holt, Cheryl L; Steward, Jocelyn L; Jones, Richard N; Roth, David L; Stringfellow, Erin; Gordon, Adam J; Kim, Theresa W; Austin, Erika L; Henry, Stephen Randal; Kay Johnson, N; Shanette Granstaff, U; O'Connell, James J; Golden, Joya F; Young, Alexander S; Davis, Lori L; Pollio, David E

2013-12-01

We compared homeless patients' experiences of care in health care organizations that differed in their degree of primary care design service tailoring. We surveyed homeless-experienced patients (either recently or currently homeless) at 3 Veterans Affairs (VA) mainstream primary care settings in Pennsylvania and Alabama, a homeless-tailored VA clinic in California, and a highly tailored non-VA Health Care for the Homeless Program in Massachusetts (January 2011-March 2012). We developed a survey, the "Primary Care Quality-Homeless Survey," to reflect the concerns and aspirations of homeless patients. Mean scores at the tailored non-VA site were superior to those from the 3 mainstream VA sites (P < .001). Adjusting for patient characteristics, these differences remained significant for subscales assessing the patient-clinician relationship (P < .001) and perceptions of cooperation among providers (P = .004). There were 1.5- to 3-fold increased odds of an unfavorable experience in the domains of the patient-clinician relationship, cooperation, and access or coordination for the mainstream VA sites compared with the tailored non-VA site; the tailored VA site attained intermediate results. Tailored primary care service design was associated with a superior service experience for patients who experienced homelessness.

Tailoring plasmonic nanoparticles and fractal patterns

NASA Astrophysics Data System (ADS)

Rosa, Lorenzo; Juodkazis, Saulius

2011-12-01

We studied new three-dimensional tailoring of nano-particles by ion-beam and electron-beam lithographies, aiming for features and nano-gaps down to 10 nm size. Electron-beam patterning is demonstrated for 2D fabrication in combination with plasmonic metal deposition and lift-off, with full control of spectral features of plasmonic nano-particles and patterns on dielectric substrates. We present wide-angle bow-tie rounded nano-antennas whose plasmonic resonances achieve strong field enhancement at engineered wavelength range, and show how the addition of fractal patterns defined by standard electron beam lithography achieve light field enhancement from visible to far-IR spectral range and scalable up towards THz band. Field enhancement is evaluated by FDTD modeling on full-3D simulation domains using complex material models, showing the modeling method capabilities and the effect of staircase approximations on field enhancement and resonance conditions, especially at metal corners, where a minimum rounding radius of 2 nm is resolved and a five-fold reduction of spurious ringing at sharp corners is obtained by the use of conformal meshing.

Continuation of tailored composite structures of ordered staple thermoplastic material

NASA Technical Reports Server (NTRS)

Santare, Michael H.; Pipes, R. Byron

1992-01-01

The search for the cost effective composite structure has motivated the investigation of several approaches to develop composite structure from innovative material forms. Among the promising approaches is the conversion of a planar sheet to components of complex curvature through sheet forming or stretch forming. In both cases, the potential for material stretch in the fiber direction appears to offer a clear advantage in formability over continuous fiber systems. A framework was established which allows the simulation of the anisotropic mechanisms of deformation of long discontinuous fiber laminates wherein the matrix phase is a viscous fluid. Predictions for the effective viscosities of a hyper-anisotropic medium consisting of collimated, discontinuous fibers suspended in viscous matrix were extended to capture the characteristics of typical polymers including non-Newtonian behavior and temperature dependence. In addition, the influence of fiber misorientation was also modeled by compliance averaging to determine ensemble properties for a given orientation distribution. A design tool is presented for predicting the effect of material heterogeneity on the performance of curved composite beams such as those used in aircraft fuselage structures. Material heterogeneity can be induced during manufacturing processes such as sheet forming and stretch forming of thermoplastic composites. This heterogeneity can be introduced in the form of fiber realignment and spreading during the manufacturing process causing radial and tangential gradients in material properties. Two analysis procedures are used to solve the beam problems. The first method uses separate two-dimensional elasticity solutions for the stresses in the flange and web sections of the beam. The separate solutions are coupled by requiring that forces and displacements match section boundaries. The second method uses an approximate Rayleigh-Ritz technique to find the solutions for more complex beams. Analyses

Tailored tools to improve pharmacotherapy in infants.

PubMed

Allegaert, Karel

2014-08-01

Extensive within-population variability is the essence of neonatal pharmacology. Despite this, infants remain one of the last therapeutic orphans. Together with additional legal initiatives, tailoring of already available tools (modeling, covariates, pharmacovigilance) may significantly improve pharmacotherapy in infants. Modeling approaches that hold the promise to improve pharmacotherapy in infants are between-compound extrapolation for compounds that undergo the same route of elimination and integration of time-varying physiology to adapt for the fast maturational changes. Besides these maturational covariates (size, age), newly emerging covariates relate to novel treatment modalities (extracorporeal circulation, hypothermia), environmental issues (microbiome, critical illness) or pharmacogenetics. All these covariates interact with the maturational variation. Finally, pharmacovigilance also needs to be tailored to the characteristics of this population. This relates to preventive strategies, signal detection and assessment of causality. Knowledge on pharmacotherapy in infants is lagging. Tailoring available tools to the specific characteristics (maturation) and clinical needs (newly emerging covariates) of infants is feasible but needs creativity and a multidisciplinary collaboration between modelers, academia, clinical researchers and, obviously, the public, including parents.

Ultrathin 2D Photocatalysts: Electronic-Structure Tailoring, Hybridization, and Applications.

PubMed

Di, Jun; Xiong, Jun; Li, Huaming; Liu, Zheng

2018-01-01

As a sustainable technology, semiconductor photocatalysis has attracted considerable interest in the past several decades owing to the potential to relieve or resolve energy and environmental-pollution issues. By virtue of their unique structural and electronic properties, emerging ultrathin 2D materials with appropriate band structure show enormous potential to achieve efficient photocatalytic performance. Here, the state-of-the-art progress on ultrathin 2D photocatalysts is reviewed and a critical appraisal of the classification, controllable synthesis, and formation mechanism of ultrathin 2D photocatalysts is presented. Then, different strategies to tailor the electronic structure of ultrathin 2D photocatalysts are summarized, including component tuning, thickness tuning, doping, and defect engineering. Hybridization with the introduction of a foreign component and maintaining the ultrathin 2D structure is presented to further boost the photocatalytic performance, such as quantum dots/2D materials, single atoms/2D materials, molecular/2D materials, and 2D-2D stacking materials. More importantly, the advancement of versatile photocatalytic applications of ultrathin 2D photocatalysts in the fields of water oxidation, hydrogen evolution, CO 2 reduction, nitrogen fixation, organic syntheses, and removal pollutants is discussed. Finally, the future opportunities and challenges regarding ultrathin 2D photocatalysts to bring about new opportunities for future research in the field of photocatalysis are also presented. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A Comparison of a Bayesian and a Maximum Likelihood Tailored Testing Procedure.

ERIC Educational Resources Information Center

McKinley, Robert L.; Reckase, Mark D.

A study was conducted to compare tailored testing procedures based on a Bayesian ability estimation technique and on a maximum likelihood ability estimation technique. The Bayesian tailored testing procedure selected items so as to minimize the posterior variance of the ability estimate distribution, while the maximum likelihood tailored testing…

LPWA using supersonic gas jet with tailored density profile

NASA Astrophysics Data System (ADS)

Kononenko, O.; Bohlen, S.; Dale, J.; D'Arcy, R.; Dinter, M.; Erbe, J. H.; Indorf, G.; di Lucchio, L.; Goldberg, L.; Gruse, J. N.; Karstensen, S.; Libov, V.; Ludwig, K.; Martinez de La Ossa, A.; Marutzky, F.; Niroula, A.; Osterhoff, J.; Quast, M.; Schaper, L.; Schwinkendorf, J.-P.; Streeter, M.; Tauscher, G.; Weichert, S.; Palmer, C.; Horbatiuk, Taras

2016-10-01

Laser driven plasma wakefield accelerators have been explored as a potential compact, reproducible source of relativistic electron bunches, utilising an electric field of many GV/m. Control over injection of electrons into the wakefield is of crucial importance in producing stable, mono-energetic electron bunches. Density tailoring of the target, to control the acceleration process, can also be used to improve the quality of the bunch. By using gas jets to provide tailored targets it is possible to provide good access for plasma diagnostics while also producing sharp density gradients for density down-ramp injection. OpenFOAM hydrodynamic simulations were used to investigate the possibility of producing tailored density targets in a supersonic gas jet. Particle-in-cell simulations of the resulting density profiles modelled the effect of the tailored density on the properties of the accelerated electron bunch. Here, we present the simulation results together with preliminary experimental measurements of electron and x-ray properties from LPWA experiments using gas jet targets and a 25 TW, 25 fs Ti:Sa laser system at DESY.

Addressing medication nonadherence by mobile phone: development and delivery of tailored messages.

PubMed

Gatwood, Justin; Balkrishnan, Rajesh; Erickson, Steven R; An, Lawrence C; Piette, John D; Farris, Karen B

2014-01-01

Medication nonadherence remains a significant public health problem, and efforts to improve adherence have shown only limited impact. The tailoring of messages has become a popular method of developing communication to influence specific health-related behaviors but the development and impact of tailored text messages on medication use is poorly understood. The aim of this paper is to describe an approach to developing theory-based tailored messages for delivery via mobile phone to improve medication adherence among patients with diabetes. Kreuter's five-step tailoring process was followed to create tailored messages for mobile phone delivery. Two focus group sessions, using input from 11 people, and expert review of message content were used to adapt the survey instrument on which the messages were tailored and edit the developed messages for the target population. Following established tailoring methods a library of 168 theory-driven and 128 medication-specific tailored messages were developed and formatted for automated delivery to mobile phones. Concepts from the Health Belief Model and Self-Determination Theory were used to craft the messages and an algorithm was applied to determine the order and timing of messages with the aim of progressively influencing disease and treatment-related beliefs driving adherence to diabetes medication. The process described may be applied to future investigations aiming to improve medication adherence in patients with diabetes and the effectiveness of the current messages will be tested in a planned analysis. Copyright © 2014 Elsevier Inc. All rights reserved.

Voltage sensor and dielectric material

DOEpatents

Yakymyshyn, Christopher Paul; Yakymyshyn, Pamela Jane; Brubaker, Michael Allen

2006-10-17

A voltage sensor is described that consists of an arrangement of impedance elements. The sensor is optimized to provide an output ratio that is substantially immune to changes in voltage, temperature variations or aging. Also disclosed is a material with a large and stable dielectric constant. The dielectric constant can be tailored to vary with position or direction in the material.

FWP executive summaries, Basic Energy Sciences Materials Sciences Programs (SNL/NM)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Samara, G.A.

1997-05-01

The BES Materials Sciences Program has the central theme of Scientifically Tailored Materials. The major objective of this program is to combine Sandia`s expertise and capabilities in the areas of solid state sciences, advanced atomic-level diagnostics and materials synthesis and processing science to produce new classes of tailored materials as well as to enhance the properties of existing materials for US energy applications and for critical defense needs. Current core research in this program includes the physics and chemistry of ceramics synthesis and processing, the use of energetic particles for the synthesis and study of materials, tailored surfaces and interfacesmore » for materials applications, chemical vapor deposition sciences, artificially-structured semiconductor materials science, advanced growth techniques for improved semiconductor structures, transport in unconventional solids, atomic-level science of interfacial adhesion, high-temperature superconductors, and the synthesis and processing of nano-size clusters for energy applications. In addition, the program includes the following three smaller efforts initiated in the past two years: (1) Wetting and Flow of Liquid Metals and Amorphous Ceramics at Solid Interfaces, (2) Field-Structured Anisotropic Composites, and (3) Composition-Modulated Semiconductor Structures for Photovoltaic and Optical Technologies. The latter is a joint effort with the National Renewable Energy Laboratory. Separate summaries are given of individual research areas.« less

Dye Wastewater Cleanup by Graphene Composite Paper for Tailorable Supercapacitors.

PubMed

Yu, Dandan; Wang, Hua; Yang, Jie; Niu, Zhiqiang; Lu, Huiting; Yang, Yun; Cheng, Liwei; Guo, Lin

2017-06-28

Currently, the energy crisis and environmental pollution are two critical challenges confronted by humans. The development of smart strategies to address the above-mentioned issues simultaneously is significant. As the main accomplices for water pollution, several kinds of organic dyes with intrinsic redox functional groups such as phenothiazines derivatives, anthraquinone, and indigoid dyes are potential candidates for the replacement of the conventional pseudocapacitive materials. In this work, three typical organic dyes can be efficiently removed by a facile adsorption procedure using reduced graphene oxide coated cellulose fiber (rGO@CF) paper. Flexible supercapacitors based on dye/rGO@CF electrodes exhibit excellent electrochemical performances that are superior to or comparable with those of conventional pseudocapacitive materials based devices, presenting a new type of promising electrode materials. Moreover, benefiting from the high flexibility and considerable mechanical strength of the graphene composite paper, the operating potential and capacitance of the devices can be easily adjusted by tailoring the hybrid electrodes into different specific shapes followed by rational integrating. The smart design of these dye/rGO@CF paper based electrodes shows that energy storage and environmental remediation can be achieved simultaneously.

Comparing Homeless Persons’ Care Experiences in Tailored Versus Nontailored Primary Care Programs

PubMed Central

Holt, Cheryl L.; Steward, Jocelyn L.; Jones, Richard N.; Roth, David L.; Stringfellow, Erin; Gordon, Adam J.; Kim, Theresa W.; Austin, Erika L.; Henry, Stephen Randal; Kay Johnson, N.; Shanette Granstaff, U.; O’Connell, James J.; Golden, Joya F.; Young, Alexander S.; Davis, Lori L.; Pollio, David E.

2013-01-01

Objectives. We compared homeless patients’ experiences of care in health care organizations that differed in their degree of primary care design service tailoring. Methods. We surveyed homeless-experienced patients (either recently or currently homeless) at 3 Veterans Affairs (VA) mainstream primary care settings in Pennsylvania and Alabama, a homeless-tailored VA clinic in California, and a highly tailored non-VA Health Care for the Homeless Program in Massachusetts (January 2011-March 2012). We developed a survey, the “Primary Care Quality-Homeless Survey," to reflect the concerns and aspirations of homeless patients. Results. Mean scores at the tailored non-VA site were superior to those from the 3 mainstream VA sites (P < .001). Adjusting for patient characteristics, these differences remained significant for subscales assessing the patient–clinician relationship (P < .001) and perceptions of cooperation among providers (P = .004). There were 1.5- to 3-fold increased odds of an unfavorable experience in the domains of the patient–clinician relationship, cooperation, and access or coordination for the mainstream VA sites compared with the tailored non-VA site; the tailored VA site attained intermediate results. Conclusions. Tailored primary care service design was associated with a superior service experience for patients who experienced homelessness. PMID:24148052

Computer-Supported Feedback Message Tailoring for Healthcare Providers in Malawi: Proof-of-Concept.

PubMed

Landis-Lewis, Zach; Douglas, Gerald P; Hochheiser, Harry; Kam, Matthew; Gadabu, Oliver; Bwanali, Mwatha; Jacobson, Rebecca S

2015-01-01

Although performance feedback has the potential to help clinicians improve the quality and safety of care, healthcare organizations generally lack knowledge about how this guidance is best provided. In low-resource settings, tools for theory-informed feedback tailoring may enhance limited clinical supervision resources. Our objectives were to establish proof-of-concept for computer-supported feedback message tailoring in Malawi, Africa. We conducted this research in five stages: clinical performance measurement, modeling the influence of feedback on antiretroviral therapy (ART) performance, creating a rule-based message tailoring process, generating tailored messages for recipients, and finally analysis of performance and message tailoring data. We retrospectively generated tailored messages for 7,448 monthly performance reports from 11 ART clinics. We found that tailored feedback could be routinely generated for four guideline-based performance indicators, with 35% of reports having messages prioritized to optimize the effect of feedback. This research establishes proof-of-concept for a novel approach to improving the use of clinical performance feedback in low-resource settings and suggests possible directions for prospective evaluations comparing alternative designs of feedback messages.

The Promise of Tailoring Incentives for Healthy Behaviors.

PubMed

Kullgren, Jeffrey T; Williams, Geoffrey C; Resnicow, Kenneth; An, Lawrence C; Rothberg, Amy; Volpp, Kevin G; Heisler, Michele

2016-01-01

To describe how tailoring financial incentives for healthy behaviors to employees' goals, values, and aspirations might improve the efficacy of incentives. We integrate insights from self-determination theory (SDT) with principles from behavioral economics in the design of financial incentives by linking how incentives could help meet an employee's life goals, values, or aspirations. Tailored financial incentives could be more effective than standard incentives in promoting autonomous motivation necessary to initiate healthy behaviors and sustain them after incentives are removed. Previous efforts to improve the design of financial incentives have tested different incentive designs that vary the size, schedule, timing, and target of incentives. Our strategy for tailoring incentives builds on strong evidence that difficult behavior changes are more successful when integrated with important life goals and values. We outline necessary research to examine the effectiveness of this approach among at-risk employees. Instead of offering simple financial rewards for engaging in healthy behaviors, existing programs could leverage incentives to promote employees' autonomous motivation for sustained health improvements. Effective application of these concepts could lead to programs more effective at improving health, potentially at lower cost. Our approach for the first time integrates key insights from SDT, behavioral economics, and tailoring to turn an extrinsic reward for behavior change into an internalized, self-sustaining motivator for long-term engagement in risk-reducing behaviors.

Decision Support and the Effectiveness of Web-based Delivery and Information Tailoring for Bowel Cancer Screening: An Exploratory Study

PubMed Central

Wilson, Carlene J; Zajac, Ian T; Hart, Elizabeth; McGillivray, Jane A

2012-01-01

Background Colorectal cancer (CRC) is the third most commonly diagnosed cancer in males and the second in females throughout the developed world. Population screening using fecal occult blood tests (FOBTs) facilitates early detection and greater chance of survival, but participation rates are low. We developed a Web-based decision tool to provide information tailored to an individual’s decision stage for CRC screening and attitude toward screening utilizing the Preventive Health Model (PHM) and Precaution Adoption Process Model (PAPM) as theoretical frameworks for screening behavior. We describe the practical steps employed in the tool’s design and the subsequent conduct of an exploratory study. Objective To design a decision tool for CRC screening and conduct an exploratory study among average-risk men and women to (1) test the impact of message type (tailored vs non-tailored) and message delivery modality (Web-based vs paper-based) on attitudes toward screening and screening uptake, and (2) investigate the acceptability of the decision tool and relevance of materials. Methods Participants (n = 100), recruited from a population sample of men and women aged 50-76 residing in urban Adelaide, Australia, were randomly assigned to a control group or one of 4 interventions: (1) Web-based and tailored information, (2) paper-based and tailored information, (3) Web-based and non-tailored (generic) information, or (4) paper-based and non-tailored information. Participation was augmented by snowball recruitment (n = 19). Questionnaires based on PHM variables were administered pre- and post-intervention. Participants were given the opportunity to request an FOBT. Following the intervention, participants discussed the acceptability of the tool. Results Full data were available for 87.4% (104/119) of participants. Post-intervention, perceived susceptibility scores for individuals receiving tailored information increased from mean 10.6 (SD 2.1) to mean 11.8 (SD 2.2). Scores

Materials and structures/ACEE

NASA Technical Reports Server (NTRS)

1981-01-01

Light weight composites made from graphite fibers, glass, or man made materials held in an epoxy matrix, and their application to airframe design are reviewed. The Aircraft Energy Efficiency program is discussed. Characteristics of composites, acceptable risks, building parts and confidence, and aeroelastic tailoring are considered.

An examination of effect estimation in factorial and standardly-tailored designs

PubMed Central

Allore, Heather G; Murphy, Terrence E

2012-01-01

Background Many clinical trials are designed to test an intervention arm against a control arm wherein all subjects are equally eligible for all interventional components. Factorial designs have extended this to test multiple intervention components and their interactions. A newer design referred to as a ‘standardly-tailored’ design, is a multicomponent interventional trial that applies individual interventional components to modify risk factors identified a priori and tests whether health outcomes differ between treatment arms. Standardly-tailored designs do not require that all subjects be eligible for every interventional component. Although standardly-tailored designs yield an estimate for the net effect of the multicomponent intervention, it has not yet been shown if they permit separate, unbiased estimation of individual component effects. The ability to estimate the most potent interventional components has direct bearing on conducting second stage translational research. Purpose We present statistical issues related to the estimation of individual component effects in trials of geriatric conditions using factorial and standardly-tailored designs. The medical community is interested in second stage translational research involving the transfer of results from a randomized clinical trial to a community setting. Before such research is undertaken, main effects and synergistic and or antagonistic interactions between them should be identified. Knowledge of the relative strength and direction of the effects of the individual components and their interactions facilitates the successful transfer of clinically significant findings and may potentially reduce the number of interventional components needed. Therefore the current inability of the standardly-tailored design to provide unbiased estimates of individual interventional components is a serious limitation in their applicability to second stage translational research. Methods We discuss estimation of

A cost-effectiveness comparison of three tailored interventions to increase mammography screening.

PubMed

Saywell, Robert M; Champion, Victoria L; Skinner, Celette Sugg; Menon, Usha; Daggy, Joanne

2004-10-01

Mammography is the primary method used for breast cancer screening. However, adherence to recommended screening practices is still below acceptable levels. This study examined the cost-effectiveness of three combinations of tailored telephone and mailed intervention strategies for increasing adherence to mammography. There were 1044 participants who were randomly assigned to one of four groups. A logistic regression model with adherence as the dependent variable and group as the independent variable was used to test for significant differences, and a ratio of cost/improvement in mammogram adherence evaluated the cost-effectiveness. All three of the interventions (tailored telephone, tailored mail, and tailored telephone and mail) had significantly better adherence rates compared with the control group (usual care). However, when also considering costs, one emerged as the superior strategy. The cost-effectiveness ratios for the three interventions show that the tailored mail (letter) was the most cost-effective strategy, achieving 43.3% mammography adherence at a marginal cost of dollar 0.39 per 1% increase in women screened. The tailored mail plus telephone achieved greater adherence (49.4%), but at a higher cost (dollar 0.56 per 1% increase in women screened). A tailored mail reminder is an effective and economical intervention to increase mammography adherence. Future research should confirm this finding and address its applicability to practice in other settings.

An efficient synthesis of graphenated carbon nanotubes over the tailored mesoporous molecular sieves by chemical vapor deposition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Atchudan, R.; Department of Chemistry, CEG Campus, Anna University, Chennai 600025; Joo, Jin., E-mail: joojin@knu.ac.kr

2013-06-01

Highlights: ► Tailored 3D cubic Ni/KIT-6 with large pores was synthesized successfully. ► The new hybrid g-CNTs in large scale were synthesized using Ni/KIT-6 by CVD method. ► The use of mesoporous material by CVD method would be an ideal choice to prepare g-CNTs at reasonable cost. ► This type of g-CNTs might be a new avenue for nano-electronic applications. - Abstract: The new hybrid of graphenated carbon nanotubes (g-CNTs) was superior to either CNTs or graphene. Mesoporous 3D cubic Ni/KIT-6 were synthesized hydrothermally through organic template route and then were used as catalytic template for the production of g-CNTsmore » using acetylene as a carbon precursor by chemical vapor deposition (CVD) method. The deposited new hybrid carbon materials were purified and analyzed by various physico-chemical techniques such as XRD, TGA, SEM, TEM and Raman spectroscopy techniques. The graphitization of CNTs was confirmed by TGA and HRTEM studies. Thermal stability, surface morphology, and structural morphology of these materials were revealed by TGA, SEM and TEM analysis, respectively. Moreover, the tailored mesoporous Ni/KIT-6 molecular sieves were found to possess better quality and massive quantity of g-CNTs produced compared to other catalytic template route.« less

High-Operating-Temperature Barrier Infrared Detector with Tailorable Cutoff Wavelength

NASA Technical Reports Server (NTRS)

Ting, David Z.; Hill, Cory, J.; Soibel, Alexander; Bandara, Sumith V.; Gunapala, Sarath D.

2011-01-01

A mid-wavelength infrared (MWIR) barrier photodetector is capable of operating at higher temperature than the prevailing MWIR detectors based on InSb. The standard high-operating-temperature barrier infrared detector (HOT-BIRD) is made with an InAsSb infrared absorber that is lattice-matched to a GaSb substrate, and has a cutoff wavelength of approximately 4 microns. To increase the versatility and utility of the HOT-BIRD, it is implemented with IR absorber materials with customizable cutoff wavelengths. The HOT-BIRD can be built with the quaternary alloy GaInAsSb as the absorber, GaAlSbAs as the barrier, on a lattice-matching GaSb substrate. The cutoff wavelength of the GaInAsSb can be tailored by adjusting the alloy composition. To build a HOT-BIRD requires a matching pair of absorber and barrier materials with the following properties: (1) their valence band edges must be approximately the same to allow unimpeded hole flow, while their conduction band edges should have a large difference to form an electron barrier; and (2) the absorber and the barrier must be respectively lattice-matched and closely lattice-matched to the substrate to ensure high material quality and low defect density. To make a HOT-BIRD with cutoff wavelength shorter than 4 microns, a GaInAsSb quaternary alloy was used as the absorber, and a matching GaAlSbAs quaternary alloy as the barrier. By changing the alloy composition, the band gap of the quaternary alloy absorber can be continuously adjusted with cutoff wavelength ranging from 4 microns down to the short wavelength infrared (SWIR). By carefully choosing the alloy composition of the barrier, a HOT-BIRD structure can be formed. With this method, a HOT-BIRD can be made with continuously tailorable cutoff wavelengths from 4 microns down to the SWIR. The HOT-BIRD detector technology is suitable for making very-large-format MWIR/SWIR focal plane arrays that can be operated by passive cooling from low Earth orbit. High-operating temperature

Tailoring periodical collections to meet institutional needs.

PubMed Central

Delman, B S

1984-01-01

A system for tailoring journal collections to meet institutional needs is described. The approach is based on the view that reference work and collection development are variant and complementary forms of the same library function; both tasks have as their objective a literature response to information problems. Utilizing the tools and procedures of the reference search in response to a specific collection development problem topic, the author created a model ranked list of relevant journals. Finally, by linking the model to certain operational and environmental factors in three different health care organizations, he tailored the collection to meet the institutions' respective information needs. PMID:6375775

Multi-material Additive Manufacturing of Metamaterials with Giant, Tailorable Negative Poisson's Ratios.

PubMed

Chen, Da; Zheng, Xiaoyu

2018-06-14

Nature has evolved with a recurring strategy to achieve unusual mechanical properties through coupling variable elastic moduli from a few GPa to below KPa within a single tissue. The ability to produce multi-material, three-dimensional (3D) micro-architectures with high fidelity incorporating dissimilar components has been a major challenge in man-made materials. Here we show multi-modulus metamaterials whose architectural element is comprised of encoded elasticity ranging from rigid to soft. We found that, in contrast to ordinary architected materials whose negative Poisson's ratio is dictated by their geometry, these type of metamaterials are capable of displaying Poisson's ratios from extreme negative to zero, independent of their 3D micro-architecture. The resulting low density metamaterials is capable of achieving functionally graded, distributed strain amplification capabilities within the metamaterial with uniform micro-architectures. Simultaneous tuning of Poisson's ratio and moduli within the 3D multi-materials could open up a broad array of material by design applications ranging from flexible armor, artificial muscles, to actuators and bio-mimetic materials.

Double-tailored nonimaging reflector optics for maximum-performance solar concentration.

PubMed

Goldstein, Alex; Gordon, Jeffrey M

2010-09-01

A nonimaging strategy that tailors two mirror contours for concentration near the étendue limit is explored, prompted by solar applications where a sizable gap between the optic and absorber is required. Subtle limitations of this simultaneous multiple surface method approach are derived, rooted in the manner in which phase space boundaries can be tailored according to the edge-ray principle. The fundamental categories of double-tailored reflective optics are identified, only a minority of which can pragmatically offer maximum concentration at high collection efficiency. Illustrative examples confirm that acceptance half-angles as large as 30 mrad can be realized at a flux concentration of approximately 1000.

Architected cellular ceramics with tailored stiffness via direct foam writing

NASA Astrophysics Data System (ADS)

Muth, Joseph T.; Dixon, Patrick G.; Woish, Logan; Gibson, Lorna J.; Lewis, Jennifer A.

2017-02-01

Hierarchical cellular structures are ubiquitous in nature because of their low-density, high-specific properties, and multifunctionality. Inspired by these systems, we created lightweight ceramic architectures composed of closed-cell porous struts patterned in the form of hexagonal and triangular honeycombs by direct foam writing. The foam ink contains bubbles stabilized by attractive colloidal particles suspended in an aqueous solution. The printed and sintered ceramic foam honeycombs possess low relative density (˜6%). By tailoring their microstructure and geometry, we created honeycombs with different modes of deformation, exceptional specific stiffness, and stiffness values that span over an order of magnitude. This capability represents an important step toward the scalable fabrication of hierarchical porous materials for applications, including lightweight structures, thermal insulation, tissue scaffolds, catalyst supports, and electrodes.

The Promise of Tailoring Incentives for Healthy Behaviors

PubMed Central

Kullgren, Jeffrey T.; Williams, Geoffrey C.; Resnicow, Kenneth; An, Lawrence C.; Rothberg, Amy; Volpp, Kevin G.; Heisler, Michele

2017-01-01

Purpose To describe how tailoring financial incentives for healthy behaviors to employees’ goals, values, and aspirations might improve the efficacy of incentives. Design/methodology/approach We integrate insights from self-determination theory (SDT) with principles from behavioral economics in the design of financial incentives by linking how incentives could help meet an employee’s life goals, values, or aspirations. Findings Tailored financial incentives could be more effective than standard incentives in promoting autonomous motivation necessary to initiate healthy behaviors and sustain them after incentives are removed. Research implications Previous efforts to improve the design of financial incentives have tested different incentive designs that vary the size, schedule, timing, and target of incentives. Our strategy for tailoring incentives builds on strong evidence that difficult behavior changes are more successful when integrated with important life goals and values. We outline necessary research to examine the effectiveness of this approach among at-risk employees. Practical implications Instead of offering simple financial rewards for engaging in healthy behaviors, existing programs could leverage incentives to promote employees’ autonomous motivation for sustained health improvements. Social implications Effective application of these concepts could lead to programs more effective at improving health, potentially at lower cost. Originality/value Our approach for the first time integrates key insights from SDT, behavioral economics, and tailoring to turn an extrinsic reward for behavior change into an internalized, self-sustaining motivator for long-term engagement in risk-reducing behaviors. PMID:29242715

Final Report: Design of adaptive load mitigating materials using nonlinear stress wave tailoring

DTIC Science & Technology

2016-02-26

for granular material use). 3 • Prof. Trudy Kriven (UIUC, Materials Science) is an expert in ceramic and geopolymer fabrication. • Prof. John...Figure A5.1: Schematic diagram showing the 1D chain of spherical elements in contact with (a) a uniform linear medium and (b) a composite linear...each material point to consisting of one of the given material constituents, we allow each material point to be assigned a composite material that is

Tailoring the graphene/silicon carbide interface for monolithic wafer-scale electronics.

PubMed

Hertel, S; Waldmann, D; Jobst, J; Albert, A; Albrecht, M; Reshanov, S; Schöner, A; Krieger, M; Weber, H B

2012-07-17

Graphene is an outstanding electronic material, predicted to have a role in post-silicon electronics. However, owing to the absence of an electronic bandgap, graphene switching devices with high on/off ratio are still lacking. Here in the search for a comprehensive concept for wafer-scale graphene electronics, we present a monolithic transistor that uses the entire material system epitaxial graphene on silicon carbide (0001). This system consists of the graphene layer with its vanishing energy gap, the underlying semiconductor and their common interface. The graphene/semiconductor interfaces are tailor-made for ohmic as well as for Schottky contacts side-by-side on the same chip. We demonstrate normally on and normally off operation of a single transistor with on/off ratios exceeding 10(4) and no damping at megahertz frequencies. In its simplest realization, the fabrication process requires only one lithography step to build transistors, diodes, resistors and eventually integrated circuits without the need of metallic interconnects.

Cermet materials

DOEpatents

Kong, Peter C [Idaho Falls, ID

2008-12-23

A self-cleaning porous cermet material, filter and system utilizing the same may be used in filtering particulate and gaseous pollutants from internal combustion engines having intermetallic and ceramic phases. The porous cermet filter may be made from a transition metal aluminide phase and an alumina phase. Filler materials may be added to increase the porosity or tailor the catalytic properties of the cermet material. Additionally, the cermet material may be reinforced with fibers or screens. The porous filter may also be electrically conductive so that a current may be passed therethrough to heat the filter during use. Further, a heating element may be incorporated into the porous cermet filter during manufacture. This heating element can be coated with a ceramic material to electrically insulate the heating element. An external heating element may also be provided to heat the cermet filter during use.

Computer-tailored dietary behaviour change interventions: a systematic review

PubMed Central

Neville, Leonie M.; O'Hara, Blythe; Milat, Andrew J.

2009-01-01

Improving dietary behaviours such as increasing fruit and vegetable consumption and reducing saturated fat intake are important in the promotion of better health. Computer tailoring has shown promise as a strategy to promote such behaviours. A narrative systematic review was conducted to describe the available evidence on ‘second’-generation computer-tailored primary prevention interventions for dietary behaviour change and to determine their effectiveness and key characteristics of success. Systematic literature searches were conducted through five databases: Medline, Embase, PsycINFO, CINAHL and All EBM Reviews and by examining the reference lists of relevant articles to identify studies published in English from January 1996 to 2008. Randomized controlled trials or quasi-experimental designs with pre-test and post-test behavioural outcome data were included. A total of 13 articles were reviewed, describing the evaluation of 12 interventions, seven of which found significant positive effects of the computer-tailored interventions for dietary behaviour outcomes, one also for weight reduction outcomes. Although the evidence of short-term efficacy for computer-tailored dietary behaviour change interventions is fairly strong, the uncertainty lies in whether the reported effects are generalizable and sustained long term. Further research is required to address these limitations of the evidence. PMID:19286893

Validation of Design and Analysis Techniques of Tailored Composite Structures

NASA Technical Reports Server (NTRS)

Jegley, Dawn C. (Technical Monitor); Wijayratne, Dulnath D.

2004-01-01

Aeroelasticity is the relationship between the elasticity of an aircraft structure and its aerodynamics. This relationship can cause instabilities such as flutter in a wing. Engineers have long studied aeroelasticity to ensure such instabilities do not become a problem within normal operating conditions. In recent decades structural tailoring has been used to take advantage of aeroelasticity. It is possible to tailor an aircraft structure to respond favorably to multiple different flight regimes such as takeoff, landing, cruise, 2-g pull up, etc. Structures can be designed so that these responses provide an aerodynamic advantage. This research investigates the ability to design and analyze tailored structures made from filamentary composites. Specifically the accuracy of tailored composite analysis must be verified if this design technique is to become feasible. To pursue this idea, a validation experiment has been performed on a small-scale filamentary composite wing box. The box is tailored such that its cover panels induce a global bend-twist coupling under an applied load. Two types of analysis were chosen for the experiment. The first is a closed form analysis based on a theoretical model of a single cell tailored box beam and the second is a finite element analysis. The predicted results are compared with the measured data to validate the analyses. The comparison of results show that the finite element analysis is capable of predicting displacements and strains to within 10% on the small-scale structure. The closed form code is consistently able to predict the wing box bending to 25% of the measured value. This error is expected due to simplifying assumptions in the closed form analysis. Differences between the closed form code representation and the wing box specimen caused large errors in the twist prediction. The closed form analysis prediction of twist has not been validated from this test.

Nerve Conduction Study on Sural Nerve among Nepalese Tailors Using Mechanical Sewing Machine

PubMed Central

Yadav, Ram Lochan; Sharma, Deepak; Shah, Dev Kumar; Thakur, Dilip; Limbu, Nirmala; Islam, Md. Nazrul

2017-01-01

Introduction The use of new technologies and innovations are out of access for people living in a developing country like Nepal. The mechanical sewing machine is still in existence at a large scale and dominant all over the country. Tailoring is one of the major occupations adopted by skilled people with lower socioeconomic status and education level. Sural nerves of both right and left legs are exposed to strenuous and chronic stress exerted by chronic paddling of mechanical sewing machine with legs. Aim To evaluate the influence of chronic and strenuous paddling on right and left sural nerves. Materials and Methods The study recruited 30 healthy male tailors with median age {34(31-37.25)} years (study group), and, 30 healthy male volunteers with age {34(32-36.25)} years (control group). Anthropometric measurements (age, height, weight, BMI and length of both right and left legs) as well as cardio respiratory measurements [Systolic Blood Pressure (SBP), Dystolic Blood Pressure (DBP), Pules Rate (PR) and Respiratory Rate (RR)] were recorded for each subject. Standard nerve conduction techniques using constant measured distances were applied to evaluate sural nerve (sensory) in both legs of each individual. The differences in variables between the study and control groups were tested using Student’s t-test for parametric variables and Mann-Whitney U test for nonparametric variables. A p-value of ≤ 0.05 was considered significant. Results Age, height, weight, body mass index and leg length were not significantly different between tailors and control groups. Cardio respiratory measurements (SBP, DBP, PR and RR) were also not significantly altered between both the groups. The sensory nerve conduction velocities (m/s) of the right {44.23(42.72-47.83) vs 50(46- 54)} and left sural nerves {45.97±5.86 vs 50.67±6.59} m/s were found significantly reduced in tailors in comparison to control group. Similarly amplitudes (μv) of right sural (20.75±5.42 vs 24.10±5

Generation and Evaluation of User Tailored Responses in Multimodal Dialogue

ERIC Educational Resources Information Center

Walker, M. A.; Whittaker, S. J.; Stent, A.; Maloor, P.; Moore, J.; Johnston, M.; Vasireddy, G.

2004-01-01

When people engage in conversation, they tailor their utterances to their conversational partners, whether these partners are other humans or computational systems. This tailoring, or adaptation to the partner takes place in all facets of human language use, and is based on a "mental model" or a "user model" of the conversational partner. Such…

Selective Modification of Chitin and Chitosan: En Route to Tailored Oligosaccharides.

PubMed

Carvalho, Luísa C R; Queda, Fausto; Santos, Cátia V Almeida; Marques, M Manuel B

2016-12-19

Chitin and chitosan are attractive biopolymers with enormous structural possibilities for chemical modification, creating platforms for new chemical entities with a broad scope of applications, ranging from material science to medicine. During the last few years, incredible efforts have been dedicated to the regioselective modification of these biopolymers paving the way for improved properties and tailored activities. Herein, the most recent advances in chitin/chitosan regioselective modification, reaction conditions, selectivity, and the impact on its applications are highlighted. Moreover, the recent focus on chitooligosaccharides, their regioselective and chemoselective functionalization, as well as their role in biological studies, including molecular recognition with several biological targets are also covered. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Core-shell quantum dots tailor the fluorescence of dental resin composites.

PubMed

Alves, Leandro P; Pilla, Viviane; Murgo, Dírian O A; Munin, Egberto

2010-02-01

We characterized the optical properties, such as absorbance and fluorescence, of dental resins containing quantum dots (QD). We also determined the doping level needed to obtain a broad and nearly flat emission spectrum that provides the perception of white color. The samples studied were resin composites from Charisma (Heraeus Kulzer) prepared with CdSe/ZnS core-shell QD (0.05-0.77 mass%). The results showed that the fluorescence of dental resin composites can be tailored by using CdSe/ZnS core-shell quantum dots. QD core incorporation into dental resins allows the fabrication of restorative materials with fluorescence properties that closely match those of natural human teeth. Copyright 2009 Elsevier Ltd. All rights reserved.

Graphitic Carbon Materials Tailored for the Rapid Adsorption of Biomolecules

NASA Astrophysics Data System (ADS)

Pescatore, Nicholas A.

Sepsis is an overactive inflammatory response to an infection, with 19 million cases estimated worldwide and causing organ dysfunction if left untreated. Three pro-inflammatory cytokines are seen from literature review as vital biomarkers for sepsis and are interleukin-6 (IL-6), interleukin-8 (IL-8) and tumor necrosis factor-alpha (TNF-alpha), which have the potential to be removed by hemoperfusion. This thesis examines carbon nanomaterials for their adsorption capabilities in the search for an optimal material for blood cleansing hemoperfusion application, such as mediating the effects of sepsis. Non-porous and porous carbon polymorphs and their properties are investigated in this thesis for their protein adsorption capabilities. Polymer-derived mesoporous carbons were compared to non-porous graphene nanoplatelets (GNP's) to observe changes in adsorption capacity for cytokines between porous and non-porous materials. GNP's were functionalized via high temperature vacuum annealing, air oxidation, acid oxidation and amination treatments to understand the effect of surface chemistry on adsorption. For practical use in a hemoperfusion column, polymer-derived carbon beads and composite materials such as cryogel and PTFE-GNP composites were designed and tested for their adsorption capacity. At concentrations of IL-6, IL-8, and TNF-alpha seen in septic patients, these cytokines were completely removed from the blood after 5 minutes of incubation with GNP's. Overall, a low-cost, scalable carbon adsorbent was found to provide a novel approach of rapidly removing pro-inflammatory cytokines from septic patients.

Tailorable stimulated Brillouin scattering in nanoscale silicon waveguides.

PubMed

Shin, Heedeuk; Qiu, Wenjun; Jarecki, Robert; Cox, Jonathan A; Olsson, Roy H; Starbuck, Andrew; Wang, Zheng; Rakich, Peter T

2013-01-01

Nanoscale modal confinement is known to radically enhance the effect of intrinsic Kerr and Raman nonlinearities within nanophotonic silicon waveguides. By contrast, stimulated Brillouin-scattering nonlinearities, which involve coherent coupling between guided photon and phonon modes, are stifled in conventional nanophotonics, preventing the realization of a host of Brillouin-based signal-processing technologies in silicon. Here we demonstrate stimulated Brillouin scattering in silicon waveguides, for the first time, through a new class of hybrid photonic-phononic waveguides. Tailorable travelling-wave forward-stimulated Brillouin scattering is realized-with over 1,000 times larger nonlinearity than reported in previous systems-yielding strong Brillouin coupling to phonons from 1 to 18 GHz. Experiments show that radiation pressures, produced by subwavelength modal confinement, yield enhancement of Brillouin nonlinearity beyond those of material nonlinearity alone. In addition, such enhanced and wideband coherent phonon emission paves the way towards the hybridization of silicon photonics, microelectromechanical systems and CMOS signal-processing technologies on chip.

Tailorable stimulated Brillouin scattering in nanoscale silicon waveguides

PubMed Central

Shin, Heedeuk; Qiu, Wenjun; Jarecki, Robert; Cox, Jonathan A.; Olsson, Roy H.; Starbuck, Andrew; Wang, Zheng; Rakich, Peter T.

2013-01-01

Nanoscale modal confinement is known to radically enhance the effect of intrinsic Kerr and Raman nonlinearities within nanophotonic silicon waveguides. By contrast, stimulated Brillouin-scattering nonlinearities, which involve coherent coupling between guided photon and phonon modes, are stifled in conventional nanophotonics, preventing the realization of a host of Brillouin-based signal-processing technologies in silicon. Here we demonstrate stimulated Brillouin scattering in silicon waveguides, for the first time, through a new class of hybrid photonic–phononic waveguides. Tailorable travelling-wave forward-stimulated Brillouin scattering is realized—with over 1,000 times larger nonlinearity than reported in previous systems—yielding strong Brillouin coupling to phonons from 1 to 18 GHz. Experiments show that radiation pressures, produced by subwavelength modal confinement, yield enhancement of Brillouin nonlinearity beyond those of material nonlinearity alone. In addition, such enhanced and wideband coherent phonon emission paves the way towards the hybridization of silicon photonics, microelectromechanical systems and CMOS signal-processing technologies on chip. PMID:23739586

A Multidirectional Tribo-System: Wear of UHMWPE under Sliding, Rolling, and Rotation

NASA Astrophysics Data System (ADS)

Patten, Elias Wolfgang

Total knee replacements (TKR) have become a successful surgical procedure for addressing end-stage osteoarthritis, with ultra-high molecular weight polyethylene and cobalt chrome alloy (UHMWPE/Co-Cr) serving as the bearing materials of choice for decades. However, more than 10% of TKRs fail and require revision surgery. The predominant challenge with UHMWPE is the particulate debris generated through wear-mediated processes; wear debris from the UHMWPE tibial bearing surface leading to loosening is still the main cause for post-fifth-year revisions. UHMWPE wear in hip arthroplasty has been linked to microstructural evolution at the surface from multidirectional sliding in the hip joint but little is known about how the microstructure responds to clinically relevant sliding conditions in the knee. This is likely because wear tests are typically performed under basic motion parameters with simplified geometry (pin-on-disk tests) while the knee has more complex kinematics: it is neither a ball-and-socket joint nor a simple hinge joint, but has 2D sliding, rolling/slip motion, and rotation. There is also disagreement over how to best quantify cross-shear and how to model how much wear it will cause. A custom multidirectional tribo-system was used to investigate the individual and combined effects of the different motions in TKR: 2D sliding, rolling, and rotation, for a total of eight separate kinematic conditions. The trends in wear rates and wear factors for these different motions were compared with many different definitions for magnitudes and ratios of cross-shear. Additionally, the wear surfaces were examined for wear mechanism and the microstructural changes in lamellae orientation for the different motions were analyzed. To mimic the tribological conditions of a condyle in a TKR, polished Co-Cr spheres were articulated against flat, smooth UHMWPE disks with physiologically relevant loading, speed, and lubrication conditions. The motion parameters were selected

Coupled structural/thermal/electromagnetic analysis/tailoring of graded composite structures

NASA Technical Reports Server (NTRS)

Mcknight, R. L.; Huang, H.; Hartle, M.

1992-01-01

Accomplishments are described for the fourth years effort of a 5-year program to develop a methodology for coupled structural/thermal/electromagnetic analysis/tailoring of graded component structures. These accomplishments include: (1) demonstration of coupled solution capability; (2) alternate CSTEM electromagnetic technology; (3) CSTEM acoustic capability; (4) CSTEM tailoring; (5) CSTEM composite micromechanics using ICAN; and (6) multiple layer elements in CSTEM.

Systematic control of nonmetallic materials for improved fire safety

NASA Technical Reports Server (NTRS)

1972-01-01

The elements of a systematic fire safety program are summarized and consist of fire safety criteria, design considerations, testing of materials, development of nonmetallic materials, nonmetallic materials information systems, design reviews, and change control. The system described in this report was developed for the Apollo spacecraft. The system can, however, be tailored to many industrial, commercial, and military activities.

Tailorable and Wearable Textile Devices for Solar Energy Harvesting and Simultaneous Storage.

PubMed

Chai, Zhisheng; Zhang, Nannan; Sun, Peng; Huang, Yi; Zhao, Chuanxi; Fan, Hong Jin; Fan, Xing; Mai, Wenjie

2016-10-05

The pursuit of harmonic combination of technology and fashion intrinsically points to the development of smart garments. Herein, we present an all-solid tailorable energy textile possessing integrated function of simultaneous solar energy harvesting and storage, and we call it tailorable textile device. Our technique makes it possible to tailor the multifunctional textile into any designed shape without impairing its performance and produce stylish smart energy garments for wearable self-powering system with enhanced user experience and more room for fashion design. The "threads" (fiber electrodes) featuring tailorability and knittability can be large-scale fabricated and then woven into energy textiles. The fiber supercapacitor with merits of tailorability, ultrafast charging capability, and ultrahigh bending-resistance is used as the energy storage module, while an all-solid dye-sensitized solar cell textile is used as the solar energy harvesting module. Our textile sample can be fully charged to 1.2 V in 17 s by self-harvesting solar energy and fully discharged in 78 s at a discharge current density of 0.1 mA.

41 CFR 101-29.212 - Tailoring.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Tailoring. 101-29.212 Section 101-29.212 Public Contracts and Property Management Federal Property Management Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS SUPPLY AND PROCUREMENT 29-FEDERAL PRODUCT DESCRIPTIONS 29.2...

48 CFR 3046.791-2 - Tailoring warranty terms and conditions (USCG).

Code of Federal Regulations, 2010 CFR

2010-10-01

... appropriately tailor the warranty on a case-by-case basis, including remedies, exclusions, limitations and durations, provided the tailoring is consistent with the specific requirements of this subpart and (FAR) 48... the terms of the warranty (limitations), as appropriate, if necessary to derive a cost-effective...

Architected cellular ceramics with tailored stiffness via direct foam writing

PubMed Central

Muth, Joseph T.; Dixon, Patrick G.; Woish, Logan; Gibson, Lorna J.; Lewis, Jennifer A.

2017-01-01

Hierarchical cellular structures are ubiquitous in nature because of their low-density, high-specific properties, and multifunctionality. Inspired by these systems, we created lightweight ceramic architectures composed of closed-cell porous struts patterned in the form of hexagonal and triangular honeycombs by direct foam writing. The foam ink contains bubbles stabilized by attractive colloidal particles suspended in an aqueous solution. The printed and sintered ceramic foam honeycombs possess low relative density (∼6%). By tailoring their microstructure and geometry, we created honeycombs with different modes of deformation, exceptional specific stiffness, and stiffness values that span over an order of magnitude. This capability represents an important step toward the scalable fabrication of hierarchical porous materials for applications, including lightweight structures, thermal insulation, tissue scaffolds, catalyst supports, and electrodes. PMID:28179570

High gain photoconductive semiconductor switch having tailored doping profile zones

DOEpatents

Baca, Albert G.; Loubriel, Guillermo M.; Mar, Alan; Zutavern, Fred J; Hjalmarson, Harold P.; Allerman, Andrew A.; Zipperian, Thomas E.; O'Malley, Martin W.; Helgeson, Wesley D.; Denison, Gary J.; Brown, Darwin J.; Sullivan, Charles T.; Hou, Hong Q.

2001-01-01

A photoconductive semiconductor switch with tailored doping profile zones beneath and extending laterally from the electrical contacts to the device. The zones are of sufficient depth and lateral extent to isolate the contacts from damage caused by the high current filaments that are created in the device when it is turned on. The zones may be formed by etching depressions into the substrate, then conducting epitaxial regrowth in the depressions with material of the desired doping profile. They may be formed by surface epitaxy. They may also be formed by deep diffusion processes. The zones act to reduce the energy density at the contacts by suppressing collective impact ionization and formation of filaments near the contact and by reducing current intensity at the contact through enhanced current spreading within the zones.

Shape-Tailorable Graphene-Based Ultra-High-Rate Supercapacitor for Wearable Electronics.

PubMed

Xie, Binghe; Yang, Cheng; Zhang, Zhexu; Zou, Peichao; Lin, Ziyin; Shi, Gaoquan; Yang, Quanhong; Kang, Feiyu; Wong, Ching-Ping

2015-06-23

With the bloom of wearable electronics, it is becoming necessary to develop energy storage units, e.g., supercapacitors that can be arbitrarily tailored at the device level. Although gel electrolytes have been applied in supercapacitors for decades, no report has studied the shape-tailorable capability of a supercapacitor, for instance, where the device still works after being cut. Here we report a tailorable gel-based supercapacitor with symmetric electrodes prepared by combining electrochemically reduced graphene oxide deposited on a nickel nanocone array current collector with a unique packaging method. This supercapacitor with good flexibility and consistency showed excellent rate performance, cycling stability, and mechanical properties. As a demonstration, these tailorable supercapacitors connected in series can be used to drive small gadgets, e.g., a light-emitting diode (LED) and a minimotor propeller. As simple as it is (electrochemical deposition, stencil printing, etc.), this technique can be used in wearable electronics and miniaturized device applications that require arbitrarily shaped energy storage units.

Triple tailored nonlinear dispersion of dressed four- and six-wave mixing

NASA Astrophysics Data System (ADS)

Sun, Yanyong; Wang, Zhiguo; Zhang, Zhaoyang; Gu, Bingling; Wang, Kun; Yang, Gaoguo; Zhang, Yanpeng

2018-06-01

We investigate the spectral signals and spatial images of a probe transmission signal, four-wave mixing (FWM), and six-wave mixing (SWM) under double dressing effects in an inverted Y-type system. Especially, we get the triple tailored nonlinear dispersion (about 60 MHz) of the dressed FWM and SWM through the interaction between electromagnetically induced transparency (EIT) windows and the Kerr nonlinearity. Moreover, SWM and dressed FWM with narrow linewidth are obtained through the tailoring of the three EIT windows, which is much narrower than the EIT. In addition, we first elaborate the modulation effect from the self-Kerr coefficient of FWM on the spot. We also investigate the spatial characteristics (defocusing, shifting, and splitting) of FWM and SWM induced by tailored self-Kerr and cross-Kerr effects among the relative fields. Such spatial shifting, splitting induced by the tailored nonlinear dispersion can be used for a higher contrast and high speed switch as well as a high resolution router.

Testing a Dutch web-based tailored lifestyle programme among adults: a study protocol.

PubMed

Schulz, Daniela N; Kremers, Stef Pj; van Osch, Liesbeth Adm; Schneider, Francine; van Adrichem, Mathieu Jg; de Vries, Hein

2011-02-16

Smoking, high alcohol consumption, unhealthy eating habits and physical inactivity often lead to (chronic) diseases, such as cardiovascular diseases and cancer. Tailored online interventions have been proven to be effective in changing health behaviours. The aim of this study is to test and compare the effectiveness of two different tailoring strategies for changing lifestyle compared to a control group using a multiple health behaviour web-based approach. In our Internet-based tailored programme, the five lifestyle behaviours of smoking, alcohol intake, fruit consumption, vegetable consumption, and physical activity are addressed. This randomized controlled trial, conducted among Dutch adults, includes two experimental groups (i.e., a sequential behaviour tailoring condition and a simultaneous behaviour tailoring condition) and a control group. People in the sequential behaviour tailoring condition obtain feedback on whether their lifestyle behaviours meet the Dutch recommendations. Using a step-by-step approach, they are stimulated to continue with a computer tailored module to change only one unhealthy behaviour first. In the course of the study, they can proceed to change a second behaviour. People in the simultaneous behaviour tailoring condition receive computer tailored feedback about all their unhealthy behaviours during their first visit as a stimulation to change all unhealthy behaviours. The experimental groups can re-visit the website and can then receive ipsative feedback (i.e., current scores are compared to previous scores in order to give feedback about potential changes). The (difference in) effectiveness of the different versions of the programme will be tested and compared to a control group, in which respondents only receive a short health risk appraisal. Programme evaluations will assess satisfaction with and appreciation and personal relevance of the intervention among the respondents. Finally, potential subgroup differences pertaining to

Towards collaborative filtering recommender systems for tailored health communications.

PubMed

Marlin, Benjamin M; Adams, Roy J; Sadasivam, Rajani; Houston, Thomas K

2013-01-01

The goal of computer tailored health communications (CTHC) is to promote healthy behaviors by sending messages tailored to individual patients. Current CTHC systems collect baseline patient "profiles" and then use expert-written, rule-based systems to target messages to subsets of patients. Our main interest in this work is the study of collaborative filtering-based CTHC systems that can learn to tailor future message selections to individual patients based explicit feedback about past message selections. This paper reports the results of a study designed to collect explicit feedback (ratings) regarding four aspects of messages from 100 subjects in the smoking cessation support domain. Our results show that most users have positive opinions of most messages and that the ratings for all four aspects of the messages are highly correlated with each other. Finally, we conduct a range of rating prediction experiments comparing several different model variations. Our results show that predicting future ratings based on each user's past ratings contributes the most to predictive accuracy.

Tailoring Oxygen Sensitivity with Halide Substitution in Difluoroboron Dibenzoylmethane Polylactide Materials

PubMed Central

DeRosa, Christopher A.; Kerr, Caroline; Fan, Ziyi; Kolpaczynska, Milena; Mathew, Alexander S.; Evans, Ruffin E.; Zhang, Guoqing; Fraser, Cassandra L.

2015-01-01

The dual-emissive properties of solid-state difluoroboron β-diketonate-poly(lactic acid) (BF2bdkPLA) materials have been utilized for biological oxygen sensing. In this work, BF2dbm(X)PLA materials were synthesized, where X = H, F, Cl, Br, and I. The effects of changing the halide substituent and PLA polymer chain length on the optical properties in dilute CH2Cl2 solutions and solid-state polymer films were studied. These luminescent materials show fluorescence, phosphorescence, and lifetime tunability on the basis of molecular weight, as well as lifetime modulation via the halide substituent. Short BF2dbm(Br)PLA (6.0 kDa) and both short and long BF2dbm(I)PLA polymers (6.0 or 20.3 kDa) have fluorescence and intense phosphorescence ideal for ratiometric oxygen sensing. The lighter halide-dye polymers with hydrogen, fluorine, and chlorine substitution have longer phosphorescence lifetimes and can be utilized as ultrasensitive oxygen sensors. Photostability was also analyzed for the polymer films. PMID:26480236

Tailoring the mechanical properties of SU-8/clay nanocomposites: polymer microcantilever fabrication perspective

NASA Astrophysics Data System (ADS)

Chen, Hao; Ojijo, Vincent; Cele, Hastings; Joubert, Trudi; Suprakas, Sinha Ray; Land, Kevin

2014-06-01

SU-8/Clay nanocomposite is considered as a candidate material for microcantilever sensor fabrication. Organically modified montmorillonite clay nanoparticles are dispersed in the universally used negative photoresist polymer SU-8, for a low cost material, which is also biocompatible. If varying the clay loading of the composite material yields a variation of the Young's modulus, the tailored material stiffness presents an opportunity for fabrication of microcantilevers with tunable sensor sensitivity. With this microcantilever application perspective, mechanical and thermal properties of the material were investigated. SU-8/Clay nanocomposite samples were prepared with clay loadings from 1wt% - 10wt%. Tensile test results show a general trend of increase in composite modulus with an increase in the clay loading up to 7wt%, followed by a small drop at 10wt%. The composite material indeed yields moderate variation of the Young's modulus. It was also found that the thermal degradation peak of the material occurred at 300°C, which is beyond the operating temperature of typical microcantilever sensor applications. The fabrication of a custom designed microcantilever array chip with the SU-8/Clay nanocomposite material was achieved in a class 100 cleanroom, using spin-coating and photolithography microfabrication techniques. The optimization of the process for fabricating microcantilever with the SU-8/Clay nanocomposite material is discussed in this paper. The results of this research are promising for cheaper mass production of low cost disposable, yet sensitive, microcantilever sensor elements, including biosensor applications.

Advancements in tailored hot stamping simulations: Cooling channel and distortion analyses

NASA Astrophysics Data System (ADS)

Billur, Eren; Wang, Chao; Bloor, Colin; Holecek, Martin; Porzner, Harald; Altan, Taylan

2013-12-01

Hot stamped components have been widely used in the automotive industry in the last decade where ultra high strength is required. These parts, however, may not provide sufficient toughness to absorb crash energy. Therefore, these components are "tailored" by controlling the microstructure at various locations. Simulation of tailored hot stamped components requires more detailed analysis of microstructural changes. Furthermore, since the part is not uniformly quenched, severe distortion can be observed. CPF, together with ESI have developed a number of techniques to predict the final properties of a tailored part. This paper discusses the recent improvements in modeling distortion and die design with cooling channels.

A porous ceramic membrane tailored high-temperature supercapacitor

NASA Astrophysics Data System (ADS)

Zhang, Xin; He, Benlin; Zhao, Yuanyuan; Tang, Qunwei

2018-03-01

The supercapacitor that can operate at high-temperature are promising for markedly increase in capacitance because of accelerated charge movement. However, the state-of-the-art polymer-based membranes will decompose at high temperature. Inspired by solid oxide fuel cells, we present here the experimental realization of high-temperature supercapacitors (HTSCs) tailored with porous ceramic separator fabricated by yttria-stabilized zirconia (YSZ) and nickel oxide (NiO). Using activated carbon electrode and supporting electrolyte from potassium hydroxide (KOH) aqueous solution, a category of symmetrical HTSCs are built in comparison with a conventional polymer membrane based device. The dependence of capacitance performance on temperature is carefully studied, yielding a maximized specific capacitance of 272 F g-1 at 90 °C for the optimized HTSC tailored by NiO/YSZ membrane. Moreover, the resultant HTSC has relatively high durability when suffer repeated measurement over 1000 cycles at 90 °C, while the polymer membrane based supercapacitor shows significant reduction in capacitance at 60 °C. The high capacitance along with durability demonstrates NiO/YSZ membrane tailored HTSCs are promising in future advanced energy storage devices.

Tailored Training in Army Courses

DTIC Science & Technology

2011-10-01

evidence. Psychological Sciences in the Public Interest, 9 (3), 105-119. Putnam, R . T . (1987). Structuring and adjusting content for students: A study of...tailoring. 41 References Bickley, W. R ., Pleban, R . J., Diedrich, F., Sidman, J., Semmens, R ., & Geyer, A. (2010). Army Institutional Training...Research, 64, 1-35. Corno, L. (2008). On teaching adaptively. Educational Psychologist, 43, 161-173. Corno, L, & Snow, R . E (1986), Adapting

Clinical Trial of Tailored Activity and Eating Newsletters with Older Rural Women

PubMed Central

Walker, Susan Noble; Pullen, Carol H.; Boeckner, Linda; Hageman, Patricia A.; Hertzog, Melody; Oberdorfer, Maureen K.; Rutledge, Matthew J.

2009-01-01

Background Unhealthy diet and lack of physical activity increase rural midlife and older women’s risk for chronic diseases and premature death, and they are behind urban residents in meeting Healthy People 2010 objectives. Objectives To compare a tailored intervention based on the Health Promotion Model (HPM) and a generic intervention to increase physical activity and healthy eating among rural women. Methods In a randomized by site community-based controlled clinical trial, Wellness for Women, 225 women aged 50 to 69 years were recruited in two similar rural areas. Over 12 months, women received by mail either 18 generic newsletters or 18 newsletters computer-tailored on HPM behavior-specific cognitions (benefits, barriers, self-efficacy, and interpersonal support), activity, and eating. Outcomes at 6 and 12 months included behavioral markers and biomarkers of physical activity and eating. Data were analyzed by repeated measures ANOVA and χ2 tests (α < .05). Results Both groups significantly increased stretching and strengthening exercise and fruit and vegetable servings and decreased % calories from fat, while only the tailored group increased ≥ moderate intensity activity and decreased % calories from saturated fat from baseline to 6 months. Both groups increased stretching and strengthening exercise, while only the tailored group increased ≥ moderate activity and fruit and vegetable servings and decreased % calories from fat from baseline to 12 months. Both groups had several changes in biomarkers over the study. A higher proportion of women receiving tailored newsletters met Healthy People 2010 criteria for ≥ moderate activity, fruit and vegetable servings, and % calories from fat at 12 months. Discussion Mailed computer-tailored and generic print newsletters facilitated the adoption of change in both activity and eating over 6 months. Tailored newsletters were more efficacious in facilitating change over 12 months. PMID:19289928

Granular crystals: Nonlinear dynamics meets materials engineering

DOE PAGES

Porter, Mason A.; Kevrekidis, Panayotis G.; Daraio, Chiara

2015-11-01

In this article, the freedom to choose the size, stiffness, and spatial distribution of macroscopic particles in a lattice makes granular crystals easily tailored building blocks for shock-absorbing materials, sound-focusing devices, acoustic switches, and other exotica.

Methods and apparatus for altering material using ion beams

DOEpatents

Bloomquist, Douglas D.; Buchheit, Rudy; Greenly, John B.; McIntyre, Dale C.; Neau, Eugene L.; Stinnett, Regan W.

1996-01-01

A method and apparatus for treating material surfaces using a repetitively pulsed ion beam. In particular, a method of treating magnetic material surfaces in order to reduce surface defects, and produce amorphous fine grained magnetic material with properties that can be tailored by adjusting treatment parameters of a pulsed ion beam. In addition to a method of surface treating materials for wear and corrosion resistance using pulsed particle ion beams.

Tuning and predicting the wetting of nanoengineered material surface

NASA Astrophysics Data System (ADS)

Ramiasa-MacGregor, M.; Mierczynska, A.; Sedev, R.; Vasilev, K.

2016-02-01

The wetting of a material can be tuned by changing the roughness on its surface. Recent advances in the field of nanotechnology open exciting opportunities to control macroscopic wetting behaviour. Yet, the benchmark theories used to describe the wettability of macroscopically rough surfaces fail to fully describe the wetting behaviour of systems with topographical features at the nanoscale. To shed light on the events occurring at the nanoscale we have utilised model gradient substrata where surface nanotopography was tailored in a controlled and robust manner. The intrinsic wettability of the coatings was varied from hydrophilic to hydrophobic. The measured water contact angle could not be described by the classical theories. We developed an empirical model that effectively captures the experimental data, and further enables us to predict the wetting of surfaces with nanoscale roughness by considering the physical and chemical properties of the material. The fundamental insights presented here are important for the rational design of advanced materials having tailored surface nanotopography with predictable wettability.The wetting of a material can be tuned by changing the roughness on its surface. Recent advances in the field of nanotechnology open exciting opportunities to control macroscopic wetting behaviour. Yet, the benchmark theories used to describe the wettability of macroscopically rough surfaces fail to fully describe the wetting behaviour of systems with topographical features at the nanoscale. To shed light on the events occurring at the nanoscale we have utilised model gradient substrata where surface nanotopography was tailored in a controlled and robust manner. The intrinsic wettability of the coatings was varied from hydrophilic to hydrophobic. The measured water contact angle could not be described by the classical theories. We developed an empirical model that effectively captures the experimental data, and further enables us to predict the

Co-delivery of antigen and a lipophilic anti-inflammatory drug to cells via a tailorable nanocarrier emulsion.

PubMed

Chuan, Yap Pang; Zeng, Bi Yun; O'Sullivan, Brendan; Thomas, Ranjeny; Middelberg, Anton P J

2012-02-15

Nanotechnology promises new drug carriers that can be tailored to specific applications. Here we report a new approach to drug delivery based on tailorable nanocarrier emulsions (TNEs), motivated by a need to co-deliver a protein antigen and a lipophilic drug for specific inhibition of nuclear factor kappa B (NF-κB) in antigen presenting cells (APCs). Co-delivery for NF-κB inhibition holds promise as a strategy for the treatment of rheumatoid arthritis. We used a highly surface-active peptide (SAP) to prepare a nanosized emulsion having defined surface properties predictable from the SAP sequence. Incorporating the lipophilic drug into the oil phase at the time of emulsion formation enabled its facile packaging. The SAP is depleted from bulk during emulsification, allowing simple subsequent addition of the drug-loaded oil-in-water emulsion to a solution of protein antigen. Decoration of emulsion surface with antigen was achieved via electrostatic deposition. In vitro data showed that the TNE prepared this way was internalized and well-tolerated by model APCs, and that good suppression of NF-κB expression was achieved. This work reports a new type of nanotechnology-based carrier, a TNE, which can potentially be tailored for co-delivery of multiple therapeutic components, and can be made using simple methods using only biocompatible materials. Copyright © 2011 Elsevier Inc. All rights reserved.

Tailoring Thermal Conductivity of Single-stranded Carbon-chain Polymers through Atomic Mass Modification

PubMed Central

Liao, Quanwen; Zeng, Lingping; Liu, Zhichun; Liu, Wei

2016-01-01

Tailoring the thermal conductivity of polymers is central to enlarge their applications in the thermal management of flexible integrated circuits. Progress has been made over the past decade by fabricating materials with various nanostructures, but a clear relationship between various functional groups and thermal properties of polymers remains to be established. Here, we numerically study the thermal conductivity of single-stranded carbon-chain polymers with multiple substituents of hydrogen atoms through atomic mass modification. We find that their thermal conductivity can be tuned by atomic mass modifications as revealed through molecular dynamics simulations. The simulation results suggest that heavy homogeneous substituents do not assist heat transport and trace amounts of heavy substituents can in fact hinder heat transport substantially. Our analysis indicates that carbon chain has the biggest contribution (over 80%) to the thermal conduction in single-stranded carbon-chain polymers. We further demonstrate that atomic mass modifications influence the phonon bands of bonding carbon atoms, and the discrepancies of phonon bands between carbon atoms are responsible for the remarkable drops in thermal conductivity and large thermal resistances in carbon chains. Our study provides fundamental insight into how to tailor the thermal conductivity of polymers through variable substituents. PMID:27713563

Tailoring rice flour structure by rubbery milling for improved gluten-free baked goods.

PubMed

Brütsch, Linda; Tribolet, Liliane; Isabettini, Stéphane; Soltermann, Patrick; Baumann, Andreas; Windhab, Erich J

2018-05-10

Ever-growing demand for gluten-free products calls for the development of novel food processing techniques to widen the range of existing baked goods. Extensive research has been targeted towards recipe optimization, widely neglecting the tailoring potential of process-induced structuring of gluten-free raw materials. Herein, we address this shortcoming by demonstrating the potential of rubbery milling for the generation of structure and techno-functionality in breads obtained from a variety of rice flour types. Moisture and temperature induced state transitions during milling were exploited to tailor the physicochemical properties of the flour. Moisture addition during conditioning of the different rice varieties and milling in the rubbery state considerably decreased starch damage due to more gentle disintegration. The degree of starch damage dictated the water absorption capacity of the rice flour types. Flour types with reduced starch damage upon milling offered lower dough densities, yielding bread loafs with a higher volume and better appearance. The choice of rice variety enables fine-tuning of the final product quality by influencing the dough viscoelasticity, which defines the final loaf volume. Whole grain rice flour dramatically increased the loaf volume, whilst simultaneously offering nutritional benefits. Combining the proposed functionalised flour types with current and future advances in product recipes paves the way towards optimised gluten-free goods.

A critique of the design, implementation, and delivery of a culturally-tailored self-management education intervention: a qualitative evaluation.

PubMed

Sidhu, Manbinder S; Gale, Nicola K; Gill, Paramjit; Marshall, Tom; Jolly, Kate

2015-02-07

Self-management education is at the forefront of addressing the increasing prevalence of chronic diseases. For those at greatest risk, such as minority-ethnic and/or socio-economically deprived groups, self-management education can be culturally-tailored to encourage behavioural change. Yet, the application of culturally appropriate material and expertise within health promotion services continues to be debated. We critique the design, implementation, and delivery of a culturally-tailored self-management intervention, with particular focus on the experiences of lay educators. A mixed methods qualitative evaluation was undertaken to understand self-management service provision to culturally diverse communities (i.e. how components such as lay workers, group-based design, and culturally-appropriate educational material are intended to encourage behavioural change). We interviewed lay educators delivering the Chronic Disease Educator programme along with attendees, whilst observing workshops. Data were thematically analysed using a content-based constant comparison approach through a number of interpretative analytical stages. Lay educators felt part of the local community, relating to attendees from different races and ethnicities. However, lay educators faced challenges when addressing health beliefs and changing lifestyle practices. Culturally-tailored components aided communication, with educator's cultural awareness leading to close relationships with attendees, while the group-based design facilitated discussions of the emotional impact of illness. Lay educators bring with them a number of nuanced skills and knowledge when delivering self-management education. The development and training required for this role is inhibited by financial constraints at policy-level. The interpretation of being from the 'community' links with the identity and status of the lay role, overlapping notions of race, ethnicity, and language.

Consolidation quality and mechanical performance of stamp formed tailored blanks produced by rapid AFP

NASA Astrophysics Data System (ADS)

Slange, T. K.; Warnet, L. L.; Grouve, W. J. B.; Akkerman, R.

2018-05-01

Stamp forming is a rapid manufacturing technology used to shape flat blanks of thermoplastic composite material into three-dimensional components. The combination with rapid AFP as blank manufacturing technology can further extend the applicability of stamp forming by allowing rapid lay-up of tailored blanks and offering partial preconsolidation. In an experimental study it is demonstrated that high quality laminates with good flexural strength can be obtained by following this process route. The consolidation of ply-drop regions is demonstrated by flat laminates with a thickness step. The influence of fiber orientations, blank-tooling misalignments and AFP tolerances is investigated.

Tailoring Systems Engineering Projects for Small Satellite Missions

NASA Technical Reports Server (NTRS)

Horan, Stephen; Belvin, Keith

2013-01-01

NASA maintains excellence in its spaceflight systems by utilizing rigorous engineering processes based on over 50 years of experience. The NASA systems engineering process for flight projects described in NPR 7120.5E was initially developed for major flight projects. The design and development of low-cost small satellite systems does not entail the financial and risk consequences traditionally associated with spaceflight projects. Consequently, an approach is offered to tailoring of the processes such that the small satellite missions will benefit from the engineering rigor without overly burdensome overhead. In this paper we will outline the approaches to tailoring the standard processes for these small missions and describe how it will be applied in a proposed small satellite mission.

Characterization and tailoring of porous sol-gel dielectrics for interlayer dielectric applications

NASA Astrophysics Data System (ADS)

Rogojevic, Svetlana

A new, better insulator is needed to replace SiO2 in the next generation of microelectronic devices. The dielectric constant of porous materials can be tailored by adjusting the porosity, so that their use can be extended to more than one generation of devices. Silica xerogel films with wide range of porosities (25 90%) are fabricated by varying the rate of solvent evaporation during spin-coating. Even better porosity control is achieved by using mixtures of high and low boiling point solvents, and allowing one solvent to evaporate completely during spin-coating. The quartz crystal microbalance method was employed to measure the traces of moisture adsorbed in xerogel films of varying porosities. By employing two different surface modifiers, it is demonstrated that the level of hydrophobicity is a function of surface chemistry, and can be tailored by using a suitable surface modifier. To investigate the interaction of xerogels with other materials, metallic layers were deposited on xerogel films, and subsequently annealed. When annealed in the ambient with trace amount of oxygen, Ta and Cu films undergo morphological instabilities. These morphological changes may lead to the erroneous interpretation of the Rutherford backscattering spectra as metal diffusion. When the samples are capped with a Si3N4 layer, Cu and Ta do not show diffusion through xerogel when annealed up to 650°C. Bias-temperature stressing was conducted in order to assess Cu drift through xerogel in the presence of an electric field. Contrary to what is normally observed with other dielectrics, the leakage current and C-V curve shifts were larger with an Al electrode than with a Cu electrode. This indicates that the surface modification of xerogel can contribute to the smaller charge injection from the Cu/xerogel interface, or to the inhibition of Cu diffusion, thus offering a possibility of designing future monolayer diffusion barriers for porous materials. Two possible paths of mass transfer in

Towards Collaborative Filtering Recommender Systems for Tailored Health Communications

PubMed Central

Marlin, Benjamin M.; Adams, Roy J.; Sadasivam, Rajani; Houston, Thomas K.

2013-01-01

The goal of computer tailored health communications (CTHC) is to promote healthy behaviors by sending messages tailored to individual patients. Current CTHC systems collect baseline patient “profiles” and then use expert-written, rule-based systems to target messages to subsets of patients. Our main interest in this work is the study of collaborative filtering-based CTHC systems that can learn to tailor future message selections to individual patients based explicit feedback about past message selections. This paper reports the results of a study designed to collect explicit feedback (ratings) regarding four aspects of messages from 100 subjects in the smoking cessation support domain. Our results show that most users have positive opinions of most messages and that the ratings for all four aspects of the messages are highly correlated with each other. Finally, we conduct a range of rating prediction experiments comparing several different model variations. Our results show that predicting future ratings based on each user’s past ratings contributes the most to predictive accuracy. PMID:24551430

Flavin-catalyzed redox tailoring reactions in natural product biosynthesis.

PubMed

Teufel, Robin

2017-10-15

Natural products are distinct and often highly complex organic molecules that constitute not only an important drug source, but have also pushed the field of organic chemistry by providing intricate targets for total synthesis. How the astonishing structural diversity of natural products is enzymatically generated in biosynthetic pathways remains a challenging research area, which requires detailed and sophisticated approaches to elucidate the underlying catalytic mechanisms. Commonly, the diversification of precursor molecules into distinct natural products relies on the action of pathway-specific tailoring enzymes that catalyze, e.g., acylations, glycosylations, or redox reactions. This review highlights a selection of tailoring enzymes that employ riboflavin (vitamin B2)-derived cofactors (FAD and FMN) to facilitate unusual redox catalysis and steer the formation of complex natural product pharmacophores. Remarkably, several such recently reported flavin-dependent tailoring enzymes expand the classical paradigms of flavin biochemistry leading, e.g., to the discovery of the flavin-N5-oxide - a novel flavin redox state and oxygenating species. Copyright © 2017 Elsevier Inc. All rights reserved.

Pathways for tailoring the magnetostructural behavior of FeRh-based systems

NASA Astrophysics Data System (ADS)

Barua, Radhika

2014-03-01

The prediction of phase transition temperatures in functional materials provides dual benefits of supplying insight into fundamental drivers underlying the phase transition, as well as enabling new and improved technological applications that employ the material. In this work, studies focused on understanding the magnetostructural phase transition of FeRh as a function of elemental substitution, provides guidance for tailoring phase transitions in this compound, with possible extensions to other intermetallic-based magnetostructural compounds. Clear trends in the magnetostructural temperatures (Tt) of alloys of composition Fe(Rh1-xMx) or (Fe1-xMx) Rh (M = 3 d, 4 d or 5 d transition metals), as reported in literature since 1961, were identified and confirmed as a function of the valence band electron concentration ((s + d) electrons/atom) of the system. It is observed that substitution of 3 dor 4 delements (x <= 6.5 at%) into B2-ordered FeRh compounds causes Ttto increase to a maximum around a critical valence band electron concentration (ev *) of 8.50 electrons/atom and then decrease. Substitution of 5 delements echoes this trend but with an overall increase in Ttand a shift in ev * to 8.52 electrons/atom. For ev>8.65 electrons/atom, FeRh-based alloys cease to adopt the B2-ordered crystallographic structure in favor of the chemically disordered A1-type structure or the ordered L10-type structure. This phenomenological model has been confirmed through synthesis and characterization of FeRh alloys with Cu, Ni and Au additions. The success of this model in confirming existing data trends in chemically-substituted FeRh and predicting new composition-transition temperature correlations emphasizes the strong interplay between the electronic spin configuration, the electronic band structure, and crystal lattice of this system. Further these results provide pathways for tailoring the magnetostructural behavior and the associated functional response of FeRh-based systems

Epsilon-near-zero modes for tailored light-matter interaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Campione, Salvatore; Liu, Sheng; Benz, Alexander

Epsilon-near-zero (ENZ) modes arising from condensed-matter excitations such as phonons and plasmons are a new path for tailoring light-matter interactions at the nanoscale. Complex spectral shaping can be achieved by creating such modes in nanoscale semiconductor layers and controlling their interaction with multiple, distinct, dipole resonant systems. Examples of this behavior are presented at midinfrared frequencies for ENZ modes that are strongly coupled to metamaterial resonators and simultaneously strongly coupled to semiconductor phonons or quantum-well intersubband transitions (ISTs), resulting in double- and triple-polariton branches in transmission spectra. For the double-polariton branch case, we find that the best strategy to maximizemore » the Rabi splitting is to use a combination of a doped layer supporting an ENZ feature and a layer supporting ISTs, with overlapping ENZ and IST frequencies. As a result, this design flexibility renders this platform attractive for low-voltage tunable filters, light-emitting diodes, and efficient nonlinear composite materials.« less

Epsilon-near-zero modes for tailored light-matter interaction

DOE PAGES

Campione, Salvatore; Liu, Sheng; Benz, Alexander; ...

2015-10-20

Epsilon-near-zero (ENZ) modes arising from condensed-matter excitations such as phonons and plasmons are a new path for tailoring light-matter interactions at the nanoscale. Complex spectral shaping can be achieved by creating such modes in nanoscale semiconductor layers and controlling their interaction with multiple, distinct, dipole resonant systems. Examples of this behavior are presented at midinfrared frequencies for ENZ modes that are strongly coupled to metamaterial resonators and simultaneously strongly coupled to semiconductor phonons or quantum-well intersubband transitions (ISTs), resulting in double- and triple-polariton branches in transmission spectra. For the double-polariton branch case, we find that the best strategy to maximizemore » the Rabi splitting is to use a combination of a doped layer supporting an ENZ feature and a layer supporting ISTs, with overlapping ENZ and IST frequencies. As a result, this design flexibility renders this platform attractive for low-voltage tunable filters, light-emitting diodes, and efficient nonlinear composite materials.« less

Solid materials for removing arsenic and method thereof

DOEpatents

Coronado, Paul R.; Coleman, Sabre J.; Sanner, Robert D.; Dias, Victoria L.; Reynolds, John G.

2010-09-28

Solid materials have been developed to remove arsenic compounds from aqueous media. The arsenic is removed by passing the aqueous phase through the solid materials which can be in molded, granular, or powder form. The solid materials adsorb the arsenic leaving a purified aqueous stream. The materials are aerogels or xerogels and aerogels or xerogels and solid support structure, e.g., granulated activated carbon (GAC), mixtures. The species-specific adsorption occurs through specific chemical modifications of the solids tailored towards arsenic.

Solid materials for removing arsenic and method thereof

DOEpatents

Coronado, Paul R [Livermore, CA; Coleman, Sabre J [Oakland, CA; Sanner, Robert D [Livermore, CA; Dias, Victoria L [Livermore, CA; Reynolds, John G [San Ramon, CA

2008-07-01

Solid materials have been developed to remove arsenic compounds from aqueous media. The arsenic is removed by passing the aqueous phase through the solid materials which can be in molded, granular, or powder form. The solid materials adsorb the arsenic leaving a purified aqueous stream. The materials are aerogels or xerogels and aerogels or xerogels and solid support structure, e.g., granulated activated carbon (GAC), mixtures. The species-specific adsorption occurs through specific chemical modifications of the solids tailored towards arsenic.

Sustainable Materials Management: At Your Fingertips

EPA Pesticide Factsheets

EPA recently announced the release of the beta version of EPA’s Materials Management Wizard web application (or “M-Wiz,” for short)—that puts that wealth of knowledge at your fingertips in a guided, easy-to-use format you can tailor to your specific needs.

Management of thermal peaking factors in CONFU-B PWR assemblies using neutron poisons and tailored enrichment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Visosky, M.; Hejzlar, P.; Kazimi, M.

2006-07-01

CONFU-B assemblies are PWR assemblies containing standard Uranium fuel rods and TRU bearing inert material fuel rods and are designed to achieve net TRU destruction over a 4.5-year irradiation. These highly heterogeneous assemblies tend to exhibit large intra-assembly power peaking factors (IAPPF). Neutronic strategies to reduce IAPPF are developed. The IAPPF are calculated at the assembly level using CASMO4, and these are used to calculate the most restrictive thermal margin (the Minimum Departure from Nucleate Boiling Ratio, MDNBR) using a whole-core VIPRE-01 model. This paper examines two strategies to manage the thermal margin of a CONFU-B assembly while retaining themore » TRU destruction performance: use of neutron poisons and tailored enrichment schemes. Burnable poisons can be used to suppress BOL reactivity of fresh CONFU-B assemblies with only minor impact on MDNBR and TRU destruction performance. Tailored enrichment, along with the use of soluble boron, can achieve significant improvements in MDNBR, but at some cost to TRU destruction performance. (authors)« less

[Evidence based tailoring of cancer care for older patients].

PubMed

Hamaker, Marije E; van den Bos, Frederiek

2017-12-01

Cancer is a disease that disproportionately affects the elderly. Evidence-based treatment is the golden standard of current medical care, and this is also true for older cancer patients. In developing guidelines, all available evidence is collected, appraised and summarized. Subsequent recommendations are then translate to criteria used to judge the quality of care. The heterogeneity of the elderly population requires tailoring of care, which is the opposite of the often strictly formulated treatment recommendations in guidelines and protocols. This paper discusses several issues regarding evidence based treatment versus tailored care for older cancer patients.

Main outcomes of the FRESH START trial: a sequentially tailored, diet and exercise mailed print intervention among breast and prostate cancer survivors.

PubMed

Demark-Wahnefried, Wendy; Clipp, Elizabeth C; Lipkus, Isaac M; Lobach, David; Snyder, Denise Clutter; Sloane, Richard; Peterson, Bercedis; Macri, Jennifer M; Rock, Cheryl L; McBride, Colleen M; Kraus, William E

2007-07-01

Cancer survivors are at increased risk for cardiovascular disease, diabetes, osteoporosis, and second primary tumors. Healthful lifestyle practices may improve the health and well-being of survivors. The FRESH START trial tested the efficacy of sequentially tailored versus standardized mailed materials on improving cancer survivors' diet and exercise behaviors. Five hundred forty-three individuals with newly diagnosed locoregional breast or prostate cancer were recruited from 39 states and two provinces within North America. Participants were randomly assigned either to a 10-month program of tailored mailed print materials promoting fruit and vegetable (F&V) consumption, reducing total/saturated fat intake, and/or increasing exercise or to a 10-month program of nontailored mailed materials on diet and exercise available in the public domain. Telephone surveys conducted at baseline and 1 year assessed body mass index (BMI), dietary consumption, physical activity, and other psychosocial/behavioral indices. Clinical assessments were conducted on a 23% subsample; information was used to validate self-reports. Five hundred nineteen participants completed the 1-year follow-up (4.4% attrition; sample characteristics: 57 +/- 10.8 years old, 83% white, 56% female, 64% overweight/obese, and 0% underweight). Although both arms significantly improved their lifestyle behaviors (P < .05), significantly greater gains occurred in the FRESH START intervention versus the control arm (practice of two or more goal behaviors: +34% v +18%, P < .0001; exercise minutes per week: +59.3 v +39.2 minutes, P = .02; F&V per day: +1.1 v +0.6 servings, P = .01; total fat: -4.4% v -2.1%, P < .0001; saturated fat: -1.3% v -0.3%, P < .0001; and BMI: -0.3 v +0.1 kg/m2, respectively, P = .004). Mailed material interventions, especially those that are tailored, are effective in promoting healthful lifestyle changes among cancer survivors. Further study is needed to determine sustainability, cost to

Tinker Tailor Robot Pi -- The Project

ERIC Educational Resources Information Center

Bianchi, Lynne

2017-01-01

Tinker Tailor Robot Pi (TTRP) is an innovative curriculum development project, which started in September 2014. It involves in-service primary and secondary teachers, university academic engineers, business partners and pupils at Key Stages 1, 2 and 3 (ages 5-14). The focus of the work has been to explore how a pedagogy for primary engineering…

Tailoring Tasks to Meet Students' Needs

ERIC Educational Resources Information Center

McDuffie, Amy Roth; Wohlhuter, Kay A.; Breyfogle, M. Lynn

2011-01-01

Just as ready-made clothes may not provide a perfect fit for all bodies, math lessons may not be a perfect fit for all students. Published instructional tasks, including problems in mathematics textbooks, often need to be tailored to be meaningful, relevant, or accessible to each student. Ways are possible to take high-level reasoning tasks and…

Communicating about microbicides with women in mind: tailoring messages for specific audiences

PubMed Central

Sidibe, Sekou; Pack, Allison P; Tolley, Elizabeth E; Ryan, Elizabeth; Mackenzie, Caroline; Bockh, Emily; Githuka, George

2014-01-01

addition to HIV prevention. Conclusions If carefully tailored, microbicide communication materials may facilitate product use by women who do not currently use any HIV prevention method. Conversely, message tailoring for women with high-risk perception will help ensure that microbicides are used as additional protection, together with condoms. PMID:25224612

Communicating about microbicides with women in mind: tailoring messages for specific audiences.

PubMed

Sidibe, Sekou; Pack, Allison P; Tolley, Elizabeth E; Ryan, Elizabeth; Mackenzie, Caroline; Bockh, Emily; Githuka, George

2014-01-01

carefully tailored, microbicide communication materials may facilitate product use by women who do not currently use any HIV prevention method. Conversely, message tailoring for women with high-risk perception will help ensure that microbicides are used as additional protection, together with condoms.

Tailored reflectors for illumination.

PubMed

Jenkins, D; Winston, R

1996-04-01

We report on tailored reflector design methods that allow the placement of general illumination patterns onto a target plane. The use of a new integral design method based on the edge-ray principle of nonimaging optics gives much more compact reflector shapes by eliminating the need for a gap between the source and the reflector profile. In addition, the reflectivity of the reflector is incorporated as a design parameter. We show the performance of design for constant irradiance on a distant plane, and we show how a leading-edge-ray method may be used to achieve general illumination patterns on nearby targets.

Tailored composite wings with elastically produced chordwise camber

NASA Technical Reports Server (NTRS)

Rehfield, Lawrence W.; Chang, Stephen; Zischka, Peter J.; Pickings, Richard D.; Holl, Michael W.

1991-01-01

Four structural concepts were created which produce chordwise camber deformation that results in enhanced lift. A wing box can be tailored to utilize each of these with composites. In attempting to optimize the aerodynamic benefits, researchers found that there are two optimum designs that are of interest. There is a weight optimum which corresponds to the maximum lift per unit structural weight. There is also a lift optimum that corresponds to maximum absolute lift. Experience indicates that a large weight penalty accompanies the transition from weight to lift optimum designs. New structural models, the basic deformation mechanisms that are utilized, and typical analytical results are presented. It appears that lift enhancements of sufficient magnitude can be produced to render this type of wing tailoring of practical interest.

Using personas to tailor educational messages to the preferences of coronary heart disease patients.

PubMed

Vosbergen, S; Mulder-Wiggers, J M R; Lacroix, J P; Kemps, H M C; Kraaijenhagen, R A; Jaspers, M W M; Peek, N

2015-02-01

Although tailoring health education messages to individual characteristics of patients has shown promising results, most patient education materials still take a one-size-fits-all approach. The aim of this study was to develop a method for tailoring health education messages to patients' preferences for various message features, using the concept of personas. This is a preliminary study focused on education for coronary heart disease (CHD) patients. This study used a three-step approach. First, we created personas by (i) performing k-means cluster analysis on data from an online survey that assessed the preferences of 213 CHD patients for various message features and, (ii) creating a vivid description of the preferences per patient cluster in an iterative process with the research team. Second, we developed adaptation rules to tailor existing educational messages to the resulting personas. Third, we conducted a pilot validation by adapting nine existing educational messages to each of the personas. These messages and the resulting personas were then presented to a separate group of 38 CHD patients who visited the cardiology outpatient clinic. They were first asked to choose their most preferred, second most preferred, and least preferred persona. Subsequently, they were asked to rate three of the adapted messages; one for every of the persona choices. We created five personas that pertained to five patient clusters. Personas varied mainly on preferences for medical or lay language, current or future temporal perspective, and including or excluding explicit health risks. Fifty-five different adaptation rules were developed, primarily describing adaptations to the message's perspective, level of detail, sentence structure, and terminology. Most participants in the validation study could identify with one of the five personas, although some of them found it hard to choose. On average, 68.5% of all participants rated the messages that matched their most preferred

Tailoring the Oxygen Content of Graphite and Reduced Graphene Oxide for Specific Applications.

PubMed

Morimoto, Naoki; Kubo, Takuya; Nishina, Yuta

2016-02-25

Graphene oxide (GO) is widely recognized as a promising material in a variety of fields, but its structure and composition has yet to be fully controlled. We have developed general strategies to control the oxidation degree of graphene-like materials via two methods: oxidation of graphite by KMnO4 in H2SO4 (oGO), and reduction of highly oxidized GO by hydrazine (rGO). Even though the oxygen content may be the same, oGO and rGO have different properties, for example the adsorption ability, oxidation ability, and electron conductivity. These differences in property arise from the difference in the underlying graphitic structure and the type of defect present. Our results can be used as a guideline for the production of tailor-made graphitic carbons. As an example, we show that rGO with 23.1 wt% oxygen showed the best performance as an electrode of an electric double-layer capacitor.

Tailoring the Oxygen Content of Graphite and Reduced Graphene Oxide for Specific Applications

NASA Astrophysics Data System (ADS)

Morimoto, Naoki; Kubo, Takuya; Nishina, Yuta

2016-02-01

Graphene oxide (GO) is widely recognized as a promising material in a variety of fields, but its structure and composition has yet to be fully controlled. We have developed general strategies to control the oxidation degree of graphene-like materials via two methods: oxidation of graphite by KMnO4 in H2SO4 (oGO), and reduction of highly oxidized GO by hydrazine (rGO). Even though the oxygen content may be the same, oGO and rGO have different properties, for example the adsorption ability, oxidation ability, and electron conductivity. These differences in property arise from the difference in the underlying graphitic structure and the type of defect present. Our results can be used as a guideline for the production of tailor-made graphitic carbons. As an example, we show that rGO with 23.1 wt% oxygen showed the best performance as an electrode of an electric double-layer capacitor.

Design of materials with prescribed nonlinear properties

NASA Astrophysics Data System (ADS)

Wang, F.; Sigmund, O.; Jensen, J. S.

2014-09-01

We systematically design materials using topology optimization to achieve prescribed nonlinear properties under finite deformation. Instead of a formal homogenization procedure, a numerical experiment is proposed to evaluate the material performance in longitudinal and transverse tensile tests under finite deformation, i.e. stress-strain relations and Poissons ratio. By minimizing errors between actual and prescribed properties, materials are tailored to achieve the target. Both two dimensional (2D) truss-based and continuum materials are designed with various prescribed nonlinear properties. The numerical examples illustrate optimized materials with rubber-like behavior and also optimized materials with extreme strain-independent Poissons ratio for axial strain intervals of εi∈[0.00, 0.30].

Tailoring the energy distribution and loss of 2D plasmons

DOE PAGES

Lin, Xiao; Rivera, Nicholas; Lopez, Josue J.; ...

2016-10-25

Here, the ability to tailor the energy distribution of plasmons at the nanoscale has many applications in nanophotonics, such as designing plasmon lasers, spasers, and quantum emitters. To this end, we analytically study the energy distribution and the proper field quantization of 2D plasmons with specific examples for graphene plasmons. We find that the portion of the plasmon energy contained inside graphene (energy confinement factor) can exceed 50%, despite graphene being infinitely thin. In fact, this very high energy confinement can make it challenging to tailor the energy distribution of graphene plasmons just by modifying the surrounding dielectric environment ormore » the geometry, such as changing the separation distance between two coupled graphene layers. However, by adopting concepts of parity-time symmetry breaking, we show that tuning the loss in one of the two coupled graphene layers can simultaneously tailor the energy confinement factor and propagation characteristics, causing the phenomenon of loss-induced plasmonic transparency.« less

Experimental investigations on the state of the friction-welded joint zone in steel hybrid components after process-relevant thermo-mechanical loadings

NASA Astrophysics Data System (ADS)

Behrens, B.-A.; Bouguecha, A.; Vucetic, M.; Peshekhodov, I.; Matthias, T.; Kolbasnikov, N.; Sokolov, S.; Ganin, S.

2016-10-01

As a part of the newly established Collaborative Research Center 1153 (SFB 1153) "Process chain for the manufacturing of hybrid high-performance components by tailored forming" at the Leibniz Universität Hannover, the Institute of Forming Technology and Machines (IFUM) examines the influence of thermo-mechanical stresses on the reduced Young's modulus as well as the hardness of hybrid (steel-steel compound) joined semi-finished products. Currently the expertise in the production of bulk metal formed parts is limited to mono-materials. For manufacturing parts of hybrid materials and also for the methods of the new process routes, practical experience has to be gained. The subproject C1 within the collaborative research center 1153 with the short title "Failure Prediction" deals with the question, if the hybrid semi-finished products fulfill the thermo-mechanical demands or if they fail at the joining zone (JZ) during forging. For this purpose, stresses similar to those in the process were imposed on hybrid semi-finished products by torsion tests by using the thermo-mechanical test system Gleeble 3800. Afterwards, the specimens were examined metallographically and by nanoindentations with the help of a TriboIndenter TI950. Thus, first knowledge on the behaviour of thermo-mechanical stresses on the reduced Young's modulus and the hardness of hybrid joined semi-finished parts was gained.

Latest Advances in Antibacterial Materials

NASA Astrophysics Data System (ADS)

Loh, Xian Jun

This paper will update readers on the latest work in the area of antibacterial polymeric systems. There is extensive literature on existing systems. This complexity confines us to the latest antibacterial materials which possess (1) responsive antibacterial activity on their own; (2) anti-biofilm formation and (3) formation of antibacterial polymeric films. The objective of this review is to provide an overview of the antibacterial synthetic polymer field. In this paper, I will analyze the early promise of this technology as well as highlight potential challenges that adopters could face. The primary focus will be the application of materials to the medical industry and to show how these materials can be tailored to create responsive, customized bactericidal materials.

Robustness in spin polarization and thermoelectricity in newly tailored Mn2-based Heusler alloys

NASA Astrophysics Data System (ADS)

Yousuf, S.; Gupta, D. C.

2018-02-01

Investigation of electronic structure, magnetism, hybridization and thermoelectricity of Mn2-based Heusler alloys within the framework of DFT simulation technique have been carried out. Through the optimized ground state parameters viz., lattice constant, total energy and bulk's modulus, electronic properties, magnetic properties and thermoelectric response of new tailored materials is reported. Mechanically stable with ductile nature and 100% spin polarization could favor their use in future spintronic materials. Thermoelectric properties are investigated through the variation of carrier concentration and temperature. Power factor analysis show a way for the selection of the optimal carrier concentration responsible for increasing their thermoelectric response with temperature. The power factor of 857.51 (966.16) × 109µW K-2 m-1 s-1 at an optimal concentration of 1018 cm-3 and temperature of 800 K for Mn2YSn (Mn2ZnSn) respectively is obtained. The Seebeck coefficient portray them as p-type materials and show a linear increase with temperature and vice versa for the carrier concentrations.

Robustness in spin polarization and thermoelectricity in newly tailored Mn2-based Heusler alloys

NASA Astrophysics Data System (ADS)

Yousuf, S.; Gupta, D. C.

2018-07-01

Investigation of electronic structure, magnetism, hybridization and thermoelectricity of Mn2-based Heusler alloys within the framework of DFT simulation technique have been carried out. Through the optimized ground state parameters viz., lattice constant, total energy and bulk's modulus, electronic properties, magnetic properties and thermoelectric response of new tailored materials is reported. Mechanically stable with ductile nature and 100% spin polarization could favor their use in future spintronic materials. Thermoelectric properties are investigated through the variation of carrier concentration and temperature. Power factor analysis show a way for the selection of the optimal carrier concentration responsible for increasing their thermoelectric response with temperature. The power factor of 857.51 (966.16) × 109µW K-2 m-1 s-1 at an optimal concentration of 1018 cm-3 and temperature of 800 K for Mn2YSn (Mn2ZnSn) respectively is obtained. The Seebeck coefficient portray them as p-type materials and show a linear increase with temperature and vice versa for the carrier concentrations.

Tailoring Cognitive Behavioral Therapy to Subtypes of Voice-Hearing

PubMed Central

Smailes, David; Alderson-Day, Ben; Fernyhough, Charles; McCarthy-Jones, Simon; Dodgson, Guy

2015-01-01

Cognitive behavioral therapy (CBT) for voice-hearing (i.e., auditory verbal hallucinations; AVH) has, at best, small to moderate effects. One possible reason for this limited efficacy is that current CBT approaches tend to conceptualize voice-hearing as a homogenous experience in terms of the cognitive processes involved in AVH. However, the highly heterogeneous nature of voice-hearing suggests that many different cognitive processes may be involved in the etiology of AVH. These heterogeneous voice-hearing experiences do, however, appear to cluster into a set of subtypes, opening up the possibility of tailoring treatment to the subtype of AVH that a voice-hearer reports. In this paper, we (a) outline our rationale for tailoring CBT to subtypes of voice-hearing, (b) describe CBT for three putative subtypes of AVH (inner speech-based AVH, memory-based AVH, and hypervigilance AVH), and (c) discuss potential limitations and problems with such an approach. We conclude by arguing that tailoring CBT to subtypes of voice-hearing could prove to be a valuable therapeutic development, which may be especially effective when used in early intervention in psychosis services. PMID:26733919

A study for development of aerothermodynamic test model materials and fabrication technique

NASA Technical Reports Server (NTRS)

Dean, W. G.; Connor, L. E.

1972-01-01

A literature survey, materials reformulation and tailoring, fabrication problems, and materials selection and evaluation for fabricating models to be used with the phase-change technique for obtaining quantitative aerodynamic heat transfer data are presented. The study resulted in the selection of two best materials, stycast 2762 FT, and an alumina ceramic. Characteristics of these materials and detailed fabrication methods are presented.

Tailoring PKI for the battlespace

NASA Astrophysics Data System (ADS)

Covey, Carlin R.

2003-07-01

A Public Key Infrastructure (PKI) can provide useful communication protections for friendly forces in the battlespace. The PKI would be used in conjunction with communication facilities that are accorded physical and Type-1 cryptographic protections. The latter protections would safeguard the confidentiality and (optionally) the integrity of communications between enclaves of users, whereas the PKI protections would furnish identification, authentication, authorization and privacy services for individual users. However, Commercial-Off-the-Shelf (COTS) and most Government-Off-the-Shelf (GOTS) PKI solutions are not ideally tailored for the battlespace environment. Most PKI solutions assume a relatively static, high-bandwidth communication network, whereas communication links in the battlespace will be dynamically reconfigured and bandwidth-limited. Most enterprise-wide PKI systems assume that users will enroll and disenroll at an orderly pace, whereas the battlespace PKI "enterprise" will grow and shrink abruptly as units are deployed or withdrawn from the battlespace. COTS and GOTS PKIs are seldom required to incorporate temporary "enterprise mergers", whereas the battlespace "enterprise" will need to incorporate temporary coalitions of forces drawn from various nations. This paper addresses both well-known and novel techniques for tailoring PKI for the battlespace environment. These techniques include the design of the security architecture, the selection of appropriate options within PKI standards, and some new PKI protocols that offer significant advantages in the battlespace.

Static aeroelastic analysis and tailoring of missile control fins

NASA Technical Reports Server (NTRS)

Mcintosh, S. C., Jr.; Dillenius, M. F. E.

1989-01-01

A concept for enhancing the design of control fins for supersonic tactical missiles is described. The concept makes use of aeroelastic tailoring to create fin designs (for given planforms) that limit the variations in hinge moments that can occur during maneuvers involving high load factors and high angles of attack. It combines supersonic nonlinear aerodynamic load calculations with finite-element structural modeling, static and dynamic structural analysis, and optimization. The problem definition is illustrated. The fin is at least partly made up of a composite material. The layup is fixed, and the orientations of the material principal axes are allowed to vary; these are the design variables. The objective is the magnitude of the difference between the chordwise location of the center of pressure and its desired location, calculated for a given flight condition. Three types of constraints can be imposed: upper bounds on static displacements for a given set of load conditions, lower bounds on specified natural frequencies, and upper bounds on the critical flutter damping parameter at a given set of flight speeds and altitudes. The idea is to seek designs that reduce variations in hinge moments that would otherwise occur. The block diagram describes the operation of the computer program that accomplishes these tasks. There is an option for a single analysis in addition to the optimization.

Tailoring Thermodynamics and Kinetics for Hydrogen Storage in Complex Hydrides towards Applications.

PubMed

Liu, Yongfeng; Yang, Yaxiong; Gao, Mingxia; Pan, Hongge

2016-02-01

Solid-state hydrogen storage using various materials is expected to provide the ultimate solution for safe and efficient on-board storage. Complex hydrides have attracted increasing attention over the past two decades due to their high gravimetric and volumetric hydrogen densities. In this account, we review studies from our lab on tailoring the thermodynamics and kinetics for hydrogen storage in complex hydrides, including metal alanates, borohydrides and amides. By changing the material composition and structure, developing feasible preparation methods, doping high-performance catalysts, optimizing multifunctional additives, creating nanostructures and understanding the interaction mechanisms with hydrogen, the operating temperatures for hydrogen storage in metal amides, alanates and borohydrides are remarkably reduced. This temperature reduction is associated with enhanced reaction kinetics and improved reversibility. The examples discussed in this review are expected to provide new inspiration for the development of complex hydrides with high hydrogen capacity and appropriate thermodynamics and kinetics for hydrogen storage. © 2015 The Chemical Society of Japan & Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Technical knowledge and skills development in the informal sector in Kenya: The case of custom tailors

NASA Astrophysics Data System (ADS)

Apunda, Edwinah Amondi; de Klerk, Helena M.; Ogina, Teresa

2017-06-01

Custom tailors working in the informal sector in Nairobi, Kenya, mainly acquire technical skills through undertaking traditional apprenticeships (TAs). However, most of these tailors are semi-skilled, produce low-quality products and are often poorer than their formally trained counterparts. This qualitative case study explores the aspects of technical skills and knowledge which tailoring apprentices develop, and the factors which influence these outcomes. The findings show that apprentices do acquire basic technical skills for immediate application to ongoing tailoring activities (such as how to take body measurements, draft patterns, and cut, sew and finish constructed garments). However, apprentices do not acquire the technical knowledge that underpins the trade. Most master tailors who have completed TAs lack technical knowledge and have no access to technical skills upgrading. This perpetuates the cycle of basic and limited technical skills transfer to apprentices, poor performance and poverty among tailors. Both apprentices and master tailors expressed concern over knowledge limitations in TAs and a need to access further training to improve skills and acquire knowledge of the trade. The authors of this article argue that, technically and pedagogically, skilled master tailors are critical to improving training quality. Complementary training in theoretical knowledge is also important in improving apprentices' technical skills and understanding of the trade. Inclusion of TAs in government policy may help ensure sustainable improvement of skills.

Cost-Effectiveness and Cost-Utility of Internet-Based Computer Tailoring for Smoking Cessation

PubMed Central

Evers, Silvia MAA; de Vries, Hein; Hoving, Ciska

2013-01-01

Background Although effective smoking cessation interventions exist, information is limited about their cost-effectiveness and cost-utility. Objective To assess the cost-effectiveness and cost-utility of an Internet-based multiple computer-tailored smoking cessation program and tailored counseling by practice nurses working in Dutch general practices compared with an Internet-based multiple computer-tailored program only and care as usual. Methods The economic evaluation was embedded in a randomized controlled trial, for which 91 practice nurses recruited 414 eligible smokers. Smokers were randomized to receive multiple tailoring and counseling (n=163), multiple tailoring only (n=132), or usual care (n=119). Self-reported cost and quality of life were assessed during a 12-month follow-up period. Prolonged abstinence and 24-hour and 7-day point prevalence abstinence were assessed at 12-month follow-up. The trial-based economic evaluation was conducted from a societal perspective. Uncertainty was accounted for by bootstrapping (1000 times) and sensitivity analyses. Results No significant differences were found between the intervention arms with regard to baseline characteristics or effects on abstinence, quality of life, and addiction level. However, participants in the multiple tailoring and counseling group reported significantly more annual health care–related costs than participants in the usual care group. Cost-effectiveness analysis, using prolonged abstinence as the outcome measure, showed that the mere multiple computer-tailored program had the highest probability of being cost-effective. Compared with usual care, in this group €5100 had to be paid for each additional abstinent participant. With regard to cost-utility analyses, using quality of life as the outcome measure, usual care was probably most efficient. Conclusions To our knowledge, this was the first study to determine the cost-effectiveness and cost-utility of an Internet-based smoking

Tailored biodegradable triblock copolymer coatings obtained by MAPLE: a parametric study

NASA Astrophysics Data System (ADS)

Brajnicov, S.; Neacsu, P.; Moldovan, A.; Marascu, V.; Bonciu, A.; Ion, R.; Dinca, V.; Cimpean, A.; Dinescu, M.

2017-11-01

Biocompatible and biodegradable coatings with controllable and tailored chemical and physical characteristics (i.e. morphology and roughness) are of great interest in bone related research applications. Within this research direction, in this work, a series of novel biodegradable coatings based on triblock copolymers poly(lactide- co-caprolactone)-block-poly(ethylene-glycol)-block-poly(lactide- co-caprolactone) (PLCL-PEG-PLCL) were obtained by matrix-assisted pulsed laser evaporation (MAPLE) and their morphological characteristics and roughness were modulated by varying target composition and laser fluence. The coatings were used for preliminary in vitro testing with MC3T3-E1 pre-osteoblasts. It was found that for a specific range of fluences, the main functional groups in the MAPLE-deposited thin films, as determined by Fourier transform infrared spectroscopy, are similar to the molecular structures of the initial material. Depending on the deposition parameters, significant changes in morphologies, i.e. material accumulation in the form of droplets, wrinkles, or carpet-like structures were revealed by atomic force microscopy (AFM) and scanning electron microscopy. The optimized coating characteristics were further correlated to MC3T3-E1 pre-osteoblasts response. The ability to control the morphology and to maintain unaltered the chemistry of the deposited material through MAPLE is an important step in creating functional bio-interfaces in the field of biomedical research and tissue engineering.

Microwavable thermal energy storage material

DOEpatents

Salyer, Ival O.

1998-09-08

A microwavable thermal energy storage material is provided which includes a mixture of a phase change material and silica, and a carbon black additive in the form of a conformable dry powder of phase change material/silica/carbon black, or solid pellets, films, fibers, moldings or strands of phase change material/high density polyethylene/ethylene-vinyl acetate/silica/carbon black which allows the phase change material to be rapidly heated in a microwave oven. The carbon black additive, which is preferably an electrically conductive carbon black, may be added in low concentrations of from 0.5 to 15% by weight, and may be used to tailor the heating times of the phase change material as desired. The microwavable thermal energy storage material can be used in food serving applications such as tableware items or pizza warmers, and in medical wraps and garments.

Translation of an Evidence-Based Tailored Childhood Injury Prevention Program

PubMed Central

Weaver, Nancy L.; Williams, Janice; Jacobsen, Heather A.; Botello-Harbaum, Maria; Glasheen, Cristie; Noelcke, Elizabeth; Nansel, Tonja R.

2008-01-01

This article describes the process of translating Safe n’ Sound, a computer-based program for parents of young children, for a general clinic environment. Safe n’ Sound is designed to reduce the risk of unintentional childhood injuries, the leading cause of death among children older than 1 year in the United States. The evidence-based program produces tailored information for parents and their healthcare provider about burns, falls, poisoning, drowning, suffocations, choking prevention, and car safety. To offer Safe n’ Sound to a broader audience, we translated the program from the form used for efficacy testing to a stand-alone application. Notable steps in this translation included (1) conducting an organizational assessment to determine the needs of the clinic staff and feasibility of implementation, (2) modifying the program to reduce length, prioritize risk areas, and update content, (3) repackaging the program to minimize cost and space requirements, and (4) developing promotional and instructional materials. Factors contributing to the success of this effort include strong collaborative partnerships, the relative advantage of Safe n’ Sound over traditional materials, the modifiable design of the program, and the support of the clinic staff and providers. Challenges and areas for future work are discussed. PMID:18287925

Tailored Educational Approaches for Consumer Health: A Model to Address Health Promotion in an Era of Personalized Medicine.

PubMed

Cohn, Wendy F; Lyman, Jason; Broshek, Donna K; Guterbock, Thomas M; Hartman, David; Kinzie, Mable; Mick, David; Pannone, Aaron; Sturz, Vanessa; Schubart, Jane; Garson, Arthur T

2018-01-01

To develop a model, based on market segmentation, to improve the quality and efficiency of health promotion materials and programs. Market segmentation to create segments (groups) based on a cross-sectional questionnaire measuring individual characteristics and preferences for health information. Educational and delivery recommendations developed for each group. General population of adults in Virginia. Random sample of 1201 Virginia residents. Respondents are representative of the general population with the exception of older age. Multiple factors known to impact health promotion including health status, health system utilization, health literacy, Internet use, learning styles, and preferences. Cluster analysis and discriminate analysis to create and validate segments. Common sized means to compare factors across segments. Developed educational and delivery recommendations matched to the 8 distinct segments. For example, the "health challenged and hard to reach" are older, lower literacy, and not likely to seek out health information. Their educational and delivery recommendations include a sixth-grade reading level, delivery through a provider, and using a "push" strategy. This model addresses a need to improve the efficiency and quality of health promotion efforts in an era of personalized medicine. It demonstrates that there are distinct groups with clearly defined educational and delivery recommendations. Health promotion professionals can consider Tailored Educational Approaches for Consumer Health to develop and deliver tailored materials to encourage behavior change.

Why are Tailored Messages More Effective? A Multiple Mediation Analysis of a Breast Cancer Screening Intervention.

PubMed

Jensen, Jakob D; King, Andy J; Carcioppolo, Nicholas; Davis, LaShara

2012-10-01

Past research has found that tailoring increases the persuasive effectiveness of a message. However, the observed effect has been small and the explanatory mechanism remains unknown. To address these shortcomings, a tailoring software program was created that personalized breast cancer screening pamphlets according to risk, health belief model constructs, and visual preference. Women aged 40 and older ( N = 119) participated in a 2 (tailored vs. stock message) × 2 (charts/graphs vs. illustrated visuals) × 3 (nested replications of the visuals) experiment. Participants provided with tailored illustrated pamphlets expressed greater breast cancer screening intentions than those provided with other pamphlets. In a test of 10 different mediators, perceived message relevance was found to fully mediate the tailoring × visual interaction.

Solid materials for removing metals and fabrication method

DOEpatents

Coronado, Paul R.; Reynolds, John G.; Coleman, Sabre J.

2004-10-19

Solid materials have been developed to remove contaminating metals and organic compounds from aqueous media. The contaminants are removed by passing the aqueous phase through the solid materials which can be in molded, granular, or powder form. The solid materials adsorb the metals and the organics leaving a purified aqueous stream. The materials are sol-gel and or sol-gel and granulated activated carbon (GAC) mixtures. The species-specific adsorption occurs through specific chemical modifications of the solids tailored towards the contaminant(s). The contaminated solid materials can then be disposed of or the contaminant can be removed and the solids recycled.

Recent advances in 2D materials for photocatalysis.

PubMed

Luo, Bin; Liu, Gang; Wang, Lianzhou

2016-04-07

Two-dimensional (2D) materials have attracted increasing attention for photocatalytic applications because of their unique thickness dependent physical and chemical properties. This review gives a brief overview of the recent developments concerning the chemical synthesis and structural design of 2D materials at the nanoscale and their applications in photocatalytic areas. In particular, recent progress on the emerging strategies for tailoring 2D material-based photocatalysts to improve their photo-activity including elemental doping, heterostructure design and functional architecture assembly is discussed.

Friction and Wear Characteristics of Candidate Foil Bearing Materials from 25 C to 800 C

NASA Technical Reports Server (NTRS)

DellaCorte, C.; Laskowski, J. A.

1996-01-01

The friction and wear behavior of unlubricated metal/metal sliding couples was investigated to screen potential candidates for high temperature foil bearings. The tribo-tests were run in an induction-heated high temperature pin-on-disk tribometer in an air atmosphere at a load of 4.9 N and at a sliding velocity of 1 m/s. The friction and wear properties of several nickel based alloys (Rene'41, Inconel X-750, Inconel 713C), iron based alloys (MA956 and Inconel 909) and a ceramic (Al2O3) were tested at 25, 500, and 800 C. In general, at elevated temperatures the alloys oxidized and formed a tenacious and lubricous oxide surface film or layer. At 800 C, Inconel X-750 versus Rene'41 had the lowest friction coefficient (0.27) and at 500 C, Inconel X-750 versus Inconel 909 the lowest pin wear (2.84 x 10(exp -6)cu mm/N-m). Gouging and severe wear of the softer material occurred whenever a significant difference in hardness existed between the pin and disk specimens.

Effects of Aeroelastic Tailoring on Anisotropic Composite Material Beam Models of Helicopter Blades

DTIC Science & Technology

1989-05-01

34 means that a layer of material at some distance above a structural midsurface reference location has the identical ply thickness, angular orientation...and material properties as that of a lamina at an identical distance below the midsurface [1]. If the fibers are placed off-axis in the upper and

The RESPECT Approach to Tailored Telephone Education

ERIC Educational Resources Information Center

Brouse, Corey H.; Basch, Charles E.; Wolf, Randi L.

2008-01-01

Objective: The objective of the RESPECT approach to tailored telephone education (TTE) is described. This approach was shown to be highly effective through a randomized intervention trial for increasing the rate of colorectal cancer (CRC) screening. Methods: At the conclusion of the trial, the investigators identified the main principles that…

Development of Tailorable Electrically Conductive Thermal Control Material Systems

NASA Technical Reports Server (NTRS)

Deshpande, M. S.; Harada, Y.

1998-01-01

The optical characteristics of surfaces on spacecraft are fundamental parameters in controlling its temperature. Passive thermal control coatings with designed solar absorptance and infrared emittance properties have been developed and been in use for some time. In this total space environment, the coating must be stable and maintain its desired optical properties for the course of the mission lifetime. The mission lifetimes are increasing and in our quest to save weight, newer substrates are being integrated which limit electrical grounding schemes. All of this has already added to the existing concerns about spacecraft charging and related spacecraft failures or operational failures. The concern is even greater for thermal control surfaces that are very large. One way of alleviating such concerns is to design new thermal control material systems (TCMS) that can help to mitigate charging via providing charge leakage paths. The object of this program was to develop two types of passive electrically conductive TCMS.

Tailoring properties of reduced graphene oxide by oxygen plasma treatment

NASA Astrophysics Data System (ADS)

Kondratowicz, Izabela; Nadolska, Małgorzata; Şahin, Samet; Łapiński, Marcin; Prześniak-Welenc, Marta; Sawczak, Mirosław; Yu, Eileen H.; Sadowski, Wojciech; Żelechowska, Kamila

2018-05-01

We report an easily controllable, eco-friendly method for tailoring the properties of reduced graphene oxide (rGO) by means of oxygen plasma. The effect of oxygen plasma treatment time (1, 5 and 10 min) on the surface properties of rGO was evaluated. Physicochemical characterization using microscopic, spectroscopic and thermal techniques was performed. The results revealed that different oxygen-containing groups (e.g. carboxyl, hydroxyl) were introduced on the rGO surface enhancing its wettability. Furthermore, upon longer treatment time, other functionalities were created (e.g. quinones, lactones). Moreover, external surface of rGO was partially etched resulting in an increase of the material surface area and porosity. Finally, the oxygen plasma-treated rGO electrodes with bilirubin oxidase were tested for oxygen reduction reaction. The study showed that rGO treated for 10 min exhibited twofold higher current density than untreated rGO. The oxygen plasma treatment may improve the enzyme adsorption on rGO electrodes by introduction of oxygen moieties and increasing the porosity.

Sensitized gelatin as a versatile biomaterial with tailored mechanical and optical properties

NASA Astrophysics Data System (ADS)

Muric, B.; Pantelic, D.; Vasiljevic, D.; Zarkov, B.; Jelenkovic, B.; Pantovic, S.; Rosic, M.

2013-11-01

We have found that gelatin doped with tot'hema (medication used for curing anemia) and eosin becomes elastic, while retaining good optical properties. The mechanical properties of tot'hema-eosin-sensitized gelatin films (TESG) have been investigated for various concentrations of tot'hema (ranging from 5 to 30% v/v). TESG specimens were prepared according to the ASTM standards for elastic materials. Tensile strength, strain at break and Young's modulus were measured. The results show that the extensibility of TESG film increases with increasing tot'hema concentration, while the Young's modulus and stress at break exponentially decrease. Mechanical properties can be tailored to suit various biomedical applications such as blood vessels, human lens capsules and biosensors based on microlenses. Tunable (strain responsive) TESG microlenses were produced and a mechanical model of blood vessels was prepared.

The cost of developing a computerized tailored interactive multimedia intervention vs. a print based Photonovella intervention for HPV vaccine education.

PubMed

Karanth, Siddharth S; Lairson, David R; Savas, Lara S; Vernon, Sally W; Fernández, María E

2017-08-01

Mobile technology is opening new avenues for healthcare providers to create and implement tailored and personalized health education programs. We estimate and compare the cost of developing an i-Pad based tailored interactive multimedia intervention (TIMI) and a print based (Photonovella) intervention to increase human papillomavirus (HPV) immunization. The development costs of the interventions were calculated using a societal perspective. Direct cost included the cost of planning the study, conducting focus groups, and developing the intervention materials by the research staff. Costs also included the amount paid to the vendors who produced the TIMI and Photonovella. Micro cost data on the staff time and materials were recorded in logs for tracking personnel time, meeting time, supplies and software purchases. The costs were adjusted for inflation and reported in 2015 USD. The total cost of developing the Photonovella was $66,468 and the cost of developing the TIMI was $135,978. The amortized annual cost for the interventions calculated at a 3% discount rate and over a 7-year period was $10,669 per year for the Photonovella and $21,825 per year for the TIMI intervention. The results would inform decision makers when planning and investing in the development of interactive multimedia health interventions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Significance of an in-situ generated boundary film on tribocorrosion behavior of polymer-metal sliding pair.

PubMed

Xu, Yongkun; Qi, Huimin; Li, Guitao; Guo, Xueping; Wan, Yong; Zhang, Ga

2018-05-15

Polymer composites have a high potential for applications as tribo-materials exposed to sea water owing to their self-lubrication characteristic and high chemical stability. In the present work, tribological behaviors of polyetheretherketone (PEEK) composites rubbing with stainless steel in sea water were explored using a pin-on-disc tribometer integrated with a potentiostat for electrochemical control. It was demonstrated that further adding 5 vol% hexagonal boron nitride (h-BN) nanoparticles into PEEK reinforced with short carbon fibers (SCF) significantly enhanced the wear resistance. Moreover, the stainless steel exhibited significantly enhanced tribocorrosion resistance when rubbing with the hybrid nanocomposite, in comparison to the sliding against PEEK filled only with SCF. Nanostructures of the boundary films formed on the steel surface were comprehensively investigated. It was manifested that tribo-chemistry products of h-BN, i.e. H 3 BO 3 and B 2 O 3 , were arrayed in a closely packed boundary film. It seems that inclusion of layer-structured H 3 BO 3 and B 2 O 3 improved the resilience of the boundary film. The continuous boundary film covering the steel surface provided a lubrication effect and strengthened the passivation layer. A new route for enhancing simultaneously tribological and corrosion resistance of polymer-metal pairs by controlling in-situ tribo-chemistry was thus proposed. Copyright © 2018 Elsevier Inc. All rights reserved.

Microwavable thermal energy storage material

DOEpatents

Salyer, I.O.

1998-09-08

A microwavable thermal energy storage material is provided which includes a mixture of a phase change material and silica, and a carbon black additive in the form of a conformable dry powder of phase change material/silica/carbon black, or solid pellets, films, fibers, moldings or strands of phase change material/high density polyethylene/ethylene vinyl acetate/silica/carbon black which allows the phase change material to be rapidly heated in a microwave oven. The carbon black additive, which is preferably an electrically conductive carbon black, may be added in low concentrations of from 0.5 to 15% by weight, and may be used to tailor the heating times of the phase change material as desired. The microwavable thermal energy storage material can be used in food serving applications such as tableware items or pizza warmers, and in medical wraps and garments. 3 figs.

Cultural Tailoring for an Afro-Caribbean Community: A Naturalistic Approach

PubMed Central

Archibald, Cynthia

2012-01-01

Purpose The purpose of this study was to discover ways to tailor health care interventions to fit the cultural identity of a minority group of people in order to reduce health disparity. Design/Analysis A naturalistic approach was used to interview four self-identified Afro-Caribbean Americans about their experiences of living on the margin. Through content analysis, categories emerged from the transcription revealed embracing, non-entitlement, enduring disrespect, and caring for self. Conclusion Afro-Caribbean Americans have strong values, healthy intentions, and appropriate attitude which are critical combinations for successfully tailoring interventions. Implications are discussed. PMID:22288207

Culturally-Tailored Smoking Cessation for American Indians: Study protocol for a randomized controlled trial

PubMed Central

2011-01-01

Background Cigarette smoking is the number one cause of preventable death among American Indian and Alaska Natives, AI/ANs. Two out of every five AI/AN will die from tobacco-related diseases if the current smoking rates of AI/ANs (40.8%) persist. Currently, there is no proven, effective culturally-tailored smoking cessation program designed specifically for a heterogeneous population of AI. The primary aim of this group randomized clinical trial is to test the efficacy of "All Nations Breath of Life" (ANBL) program compared to a non-tailored "Current Best Practices" smoking cessation program among AI smokers. Methods We will randomize 56 groups (8 smokers per group) to the tailored program or non-tailored program for a total sample size of 448 American Indian smokers. All participants in the proposed study will be offered pharmacotherapy, regardless of group assignment. This study is the first controlled trial to examine the efficacy of a culturally-tailored smoking cessation program for American Indians. If the intervention is successful, the potential health impact is significant because the prevalence of smoking is the highest in this population. Trial Registration ClinicalTrials.gov: NCT01106456 PMID:21592347

New tailor-made bio-organoclays for the remediation of olive mill waste water

NASA Astrophysics Data System (ADS)

Calabrese, Ilaria; Gelardi, Giulia; Merli, Marcello; Rytwo, Giora; Sciascia, Luciana; Liria Turco Liveri, Maria

2013-12-01

A systematic study aimed at obtaining new organoclays for the treatment of Olive Mill Waste water (OMW) has been performed. Several organoclays have been prepared by loading different amounts of the biocompatible surfactant Tween20 onto the K10 montmorillonite (MMT). Complementary kinetic and equilibrium studies on the adsorption of the Tween20 onto the MMT have been carried out and the characterization of the new tailor-made bio-materials has been performed by means of the XRD and FT-IR measurements. Finally the prepared bio-organoclays have been successfully applied for the OMW remediation and they proved to be highly effective in decreasing the organic content (OC) to an extent that depends on both the amount of loaded surfactant and the experimental protocols applied.

Electronic properties of bimetallic metal–organic frameworks (MOFs): Tailoring the density of electronic states through MOF modularity

DOE PAGES

Dolgopolova, Ekaterina A.; Brandt, Amy J.; Ejegbavwo, Otega A.; ...

2017-03-18

The development of porous well-defined hybrid materials (e.g., metal-organic frameworks or MOFs) will add a new dimension to a wide number of applications ranging from supercapacitors and electrodes to 'smart' membranes and thermoelectrics. From this perspective, the understanding and tailoring of the electronic properties of MOFs are key fundamental challenges that could unlock the full potential of these materials. In this work, we focused on the fundamental insights responsible for the electronic properties of three distinct classes of bimetallic systems, M x-yM' y-MOFs, M xM' y- MOFs, and M x(ligand-M' y)-MOFs, in which the second metal (M') incorporation occurs throughmore » (i) metal (M) replacement in the framework nodes (type I), (ii) metal node extension (type II), and (iii) metal coordination to the organic ligand (type III), respectively. We employed microwave conductivity, X-ray photoelectron spectroscopy, diffuse reflectance spectroscopy, powder X-ray diffraction, inductively coupled plasma atomic emission spectroscopy, pressed-pellet conductivity, and theoretical modeling to shed light on the key factors responsible for the tunability of MOF electronic structures. Experimental prescreening of MOFs was performed based on changes in the density of electronic states near the Fermi edge, which was used as a starting point for further selection of suitable MOFs. As a result, we demonstrated that the tailoring of MOF electronic properties could be performed as a function of metal node engineering, framework topology, and/or the presence of unsaturated metal sites while preserving framework porosity and structural integrity. Finally, these studies unveil the possible pathways for transforming the electronic properties of MOFs from insulating to semiconducting, as well as provide a blueprint for the development of hybrid porous materials with desirable electronic structures.« less

Description of the HiMAT Tailored composite structure and laboratory measured vehicle shape under load

NASA Technical Reports Server (NTRS)

Monaghan, R. C.

1981-01-01

The aeroelastically tailored outer wing and canard of the highly maneuverable aircraft technology (HiMAT) vehicle are closely examined and a general description of the overall structure of the vehicle is provided. Test data in the form of laboratory measured twist under load and predicted twist from the HiMAT NASTRAN structural design program are compared. The results of this comparison indicate that the measured twist is generally less than the NASTRAN predicted twist. These discrepancies in twist predictions are attributed, at least in part, to the inability of current analytical composite materials programs to provide sufficiently accurate properties of matrix dominated laminates for input into structural programs such as NASTRAN.

Real-Space Imaging of the Tailored Plasmons in Twisted Bilayer Graphene

NASA Astrophysics Data System (ADS)

Hu, F.; Das, Suprem R.; Luan, Y.; Chung, T.-F.; Chen, Y. P.; Fei, Z.

2017-12-01

We report a systematic plasmonic study of twisted bilayer graphene (TBLG)—two graphene layers stacked with a twist angle. Through real-space nanoimaging of TBLG single crystals with a wide distribution of twist angles, we find that TBLG supports confined infrared plasmons that are sensitively dependent on the twist angle. At small twist angles, TBLG has a plasmon wavelength comparable to that of single-layer graphene. At larger twist angles, the plasmon wavelength of TBLG increases significantly with apparently lower damping. Further analysis and modeling indicate that the observed twist-angle dependence of TBLG plasmons in the Dirac linear regime is mainly due to the Fermi-velocity renormalization, a direct consequence of interlayer electronic coupling. Our work unveils the tailored plasmonic characteristics of TBLG and deepens our understanding of the intriguing nano-optical physics in novel van der Waals coupled two-dimensional materials.

Demonstration of a terahertz pure vector beam by tailoring geometric phase.

PubMed

Wakayama, Toshitaka; Higashiguchi, Takeshi; Sakaue, Kazuyuki; Washio, Masakazu; Otani, Yukitoshi

2018-06-06

We demonstrate the creation of a vector beam by tailoring geometric phase of left- and right- circularly polarized beams. Such a vector beam with a uniform phase has not been demonstrated before because a vortex phase remains in the beam. We focus on vortex phase cancellation to generate vector beams in terahertz regions, and measure the geometric phase of the beam and its spatial distribution of polarization. We conduct proof-of-principle experiments for producing a vector beam with radial polarization and uniform phase at 0.36 THz. We determine the vortex phase of the vector beam to be below 4%, thus highlighting the extendibility and availability of the proposed concept to the super broadband spectral region from ultraviolet to terahertz. The extended range of our proposed techniques could lead to breakthroughs in the fields of microscopy, chiral nano-materials, and quantum information science.

Real-Space Imaging of the Tailored Plasmons in Twisted Bilayer Graphene

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu, F.; Das, Suprem R.; Luan, Y.

Here, we report a systematic plasmonic study of twisted bilayer graphene (TBLG)—two graphene layers stacked with a twist angle. Through real-space nanoimaging of TBLG single crystals with a wide distribution of twist angles, we find that TBLG supports confined infrared plasmons that are sensitively dependent on the twist angle. At small twist angles, TBLG has a plasmon wavelength comparable to that of single-layer graphene. At larger twist angles, the plasmon wavelength of TBLG increases significantly with apparently lower damping. Further analysis and modeling indicate that the observed twist-angle dependence of TBLG plasmons in the Dirac linear regime is mainly duemore » to the Fermi-velocity renormalization, a direct consequence of interlayer electronic coupling. Our work unveils the tailored plasmonic characteristics of TBLG and deepens our understanding of the intriguing nano-optical physics in novel van der Waals coupled two-dimensional materials.« less

Real-Space Imaging of the Tailored Plasmons in Twisted Bilayer Graphene

DOE PAGES

Hu, F.; Das, Suprem R.; Luan, Y.; ...

2017-12-13

Here, we report a systematic plasmonic study of twisted bilayer graphene (TBLG)—two graphene layers stacked with a twist angle. Through real-space nanoimaging of TBLG single crystals with a wide distribution of twist angles, we find that TBLG supports confined infrared plasmons that are sensitively dependent on the twist angle. At small twist angles, TBLG has a plasmon wavelength comparable to that of single-layer graphene. At larger twist angles, the plasmon wavelength of TBLG increases significantly with apparently lower damping. Further analysis and modeling indicate that the observed twist-angle dependence of TBLG plasmons in the Dirac linear regime is mainly duemore » to the Fermi-velocity renormalization, a direct consequence of interlayer electronic coupling. Our work unveils the tailored plasmonic characteristics of TBLG and deepens our understanding of the intriguing nano-optical physics in novel van der Waals coupled two-dimensional materials.« less

Numerical study on tailoring the shock sensitivity of TATB-based explosives using mesostructural features

NASA Astrophysics Data System (ADS)

Springer, H. Keo

2017-06-01

Advanced manufacturing techniques offer control of explosive mesostructures necessary to tailor its shock sensitivity. However, structure-property relationships are not well established for explosives so there is little material design guidance for these techniques. The objective of this numerical study is to demonstrate how TATB-based explosives can be sensitized to shocks using mesostructural features. For this study, we use LX-17 (92.5%wt TATB, 7.5%wt Kel-F 800) as the prototypical TATB-based explosive. We employ features with different geometries and materials. HMX-based explosive features, high shock impedance features, and pores are used to sensitive the LX-17. Simulations are performed in the multi-physics hydrocode, ALE3D. A reactive flow model is used to simulate the shock initiation response of the explosives. Our metric for shock sensitivity in this study is run distance to detonation as a function of applied pressure. These numerical studies are important because they guide the design of novel energetic materials. This work was performed under the auspices of the United States Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344. LLNL-ABS-724986.

Educator and participant perceptions and cost analysis of stage-tailored educational telephone calls.

PubMed

Esters, Onikia N; Boeckner, Linda S; Hubert, Melanie; Horacek, Tanya; Kritsch, Karen R; Oakland, Mary J; Lohse, Barbara; Greene, Geoffrey; Nitzke, Susan

2008-01-01

To identify strengths and weaknesses of nutrition education via telephone calls as part of a larger stage-of-change tailored intervention with mailed materials. Evaluative feedback was elicited from educators who placed the calls and respondents who received the calls. An internet and telephone survey of 10 states in the midwestern United States. 21 educators in 10 states reached via the internet and 50 young adults reached via telephone. VARIABLES MEASURED AND ANALYSIS: Rankings of intervention components, ratings of key aspects of educational calls, and cost data (as provided by a lead researcher in each state) were summarized via descriptive statistics. RESULTS, CONCLUSIONS, AND IMPLICATIONS: Educational calls used 6 to 17 minutes of preparation time, required 8 to 15 minutes of contact time, and had a mean estimated cost of $5.82 per call. Low-income young adults favored print materials over educational calls. However, the calls were reported to have positive effects on motivating participants to set goals. Educators who use educational telephone calls to reach young adults, a highly mobile target audience, may require a robust and flexible contact plan.

Tailoring surface properties of ArF resists thin films with functionally graded materials (FGM)

NASA Astrophysics Data System (ADS)

Takemoto, Ichiki; Ando, Nobuo; Edamatsu, Kunishige; Fuji, Yusuke; Kuwana, Koji; Hashimoto, Kazuhiko; Funase, Junji; Yokoyama, Hiroyuki

2007-03-01

Our recent research effort has been focused on new top coating-free 193nm immersion resists with regard to leaching of the resist components and lithographic performance. We have examined methacrylate-based resins that control the surface properties of ArF resists thin films by surface segregation behavior. For a better understanding of the surface properties of thin films, we prepared the six resins (Resin 1-6) that have three types fluorine containing monomers, a new monomer (Monomer A), Monomer B and Monomer C, respectively. We blended the base polymer (Resin 0) with Resin (1-6), respectively. We evaluated contact angles, surface properties and lithographic performances of the polymer blend resists. The static and receding contact angles of the resist that contains Resin (1-6) are greater than that of the base polymer (Resin 0) resist. The chemical composition of the surface of blend polymers was investigated with X-ray photoelectron spectroscopy (XPS). It was shown that there was significant segregation of the fluorine containing resins to the surface of the blend films. We analyzed Quantitative Structure-Property Relationships (QSPR) between the surface properties and the chemical composition of the surface of polymer blend resists. The addition of 10 wt% of the polymer (Resin 1-6) to the base polymer (Resin 0) did not influence the lithographic performance. Consequently, the surface properties of resist thin films can be tailored by the appropriate choice of fluorine containing polymer blends.

Transitioning Rationally Designed Catalytic Materials to Real 'Working' Catalysts Produced at Commercial Scale: Nanoparticle Materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schaidle, Joshua A.; Habas, Susan E.; Baddour, Frederick G.

Catalyst design, from idea to commercialization, requires multi-disciplinary scientific and engineering research and development over 10-20 year time periods. Historically, the identification of new or improved catalyst materials has largely been an empirical trial-and-error process. However, advances in computational capabilities (new tools and increased processing power) coupled with new synthetic techniques have started to yield rationally-designed catalysts with controlled nano-structures and tailored properties. This technological advancement represents an opportunity to accelerate the catalyst development timeline and to deliver new materials that outperform existing industrial catalysts or enable new applications, once a number of unique challenges associated with the scale-up ofmore » nano-structured materials are overcome.« less

Shock-loading response of advanced materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gray, G.T. III

1993-08-01

Advanced materials, such as composites (metal, ceramic, or polymer-matrix), intermetallics, foams (metallic or polymeric-based), laminated materials, and nanostructured materials are receiving increasing attention because their properties can be custom tailored specific applications. The high-rate/impact response of advanced materials is relevant to a broad range of service environments such as the crashworthiness of civilian/military vehicles, foreign-object-damage in aerospace, and light-weight armor. Increased utilization of these material classes under dynamic loading conditions requires an understanding of the relationship between high-rate/shock-wave response as a function of microstructure if we are to develop models to predict material behavior. In this paper the issues relevantmore » to defect generation, storage, and the underlying physical basis needed in predictive models for several advanced materials will be reviewed.« less

Tailored magnetic nanoparticles for optimizing magnetic fluid hyperthermia.

PubMed

Khandhar, Amit P; Ferguson, R Matthew; Simon, Julian A; Krishnan, Kannan M

2012-03-01

Magnetic Fluid Hyperthermia (MFH) is a promising approach towards adjuvant cancer therapy that is based on the localized heating of tumors using the relaxation losses of iron oxide magnetic nanoparticles (MNPs) in alternating magnetic fields (AMF). In this study, we demonstrate optimization of MFH by tailoring MNP size to an applied AMF frequency. Unlike conventional aqueous synthesis routes, we use organic synthesis routes that offer precise control over MNP size (diameter ∼10 to 25 nm), size distribution, and phase purity. Furthermore, the particles are successfully transferred to the aqueous phase using a biocompatible amphiphilic polymer, and demonstrate long-term shelf life. A rigorous characterization protocol ensures that the water-stable MNPs meet all the critical requirements: (1) uniform shape and monodispersity, (2) phase purity, (3) stable magnetic properties approaching that of the bulk, (4) colloidal stability, (5) substantial shelf life, and (6) pose no significant in vitro toxicity. Using a dedicated hyperthermia system, we then identified that 16 nm monodisperse MNPs (σ-0.175) respond optimally to our chosen AMF conditions (f = 373 kHz, H₀ = 14 kA/m); however, with a broader size distribution (σ-0.284) the Specific Loss Power (SLP) decreases by 30%. Finally, we show that these tailored MNPs demonstrate maximum hyperthermia efficiency by reducing viability of Jurkat cells in vitro, suggesting our optimization translates truthfully to cell populations. In summary, we present a way to intrinsically optimize MFH by tailoring the MNPs to any applied AMF, a required precursor to optimize dose and time of treatment. Copyright © 2011 Wiley Periodicals, Inc.

Tailored Magnetic Nanoparticles for Optimizing Magnetic Fluid Hyperthermia

PubMed Central

Khandhar, Amit; Ferguson, R. Matthew; Simon, Julian A.; Krishnan, Kannan M.

2011-01-01

Magnetic Fluid Hyperthermia (MFH) is a promising approach towards adjuvant cancer therapy that is based on the localized heating of tumors using the relaxation losses of iron oxide magnetic nanoparticles (MNPs) in alternating magnetic fields (AMF). In this study, we demonstrate optimization of MFH by tailoring MNP size to an applied AMF frequency. Unlike conventional aqueous synthesis routes, we use organic synthesis routes that offer precise control over MNP size (diameter ~ 10–25 nm), size distribution and phase purity. Furthermore, the particles are successfully transferred to the aqueous phase using a biocompatible amphiphilic polymer, and demonstrate long-term shelf life. A rigorous characterization protocol ensures that the water-stable MNPs meet all the critical requirements: (1) uniform shape and monodispersity, (2) phase purity, (3) stable magnetic properties approaching that of the bulk, (4) colloidal stability, (5) substantial shelf life and (6) pose no significant in vitro toxicity. Using a dedicated hyperthermia system, we then identified that 16 nm monodisperse MNPs (σ ~ 0.175) respond optimally to our chosen AMF conditions (f = 373 kHz, Ho = 14 kA/m); however, with a broader size distribution (σ ~ 0.284) the Specific Loss Power (SLP) decreases by 30%. Finally, we show that these tailored MNPs demonstrate maximum hyperthermia efficiency by reducing viability of Jurkat cells in vitro, suggesting our optimization translates truthfully to cell populations. In summary, we present a way to intrinsically optimize MFH by tailoring the MNPs to any applied AMF, a required precursor to optimize dose and time of treatment. PMID:22213652

Tailor-made force fields for crystal-structure prediction.

PubMed

Neumann, Marcus A

2008-08-14

A general procedure is presented to derive a complete set of force-field parameters for flexible molecules in the crystalline state on a case-by-case basis. The force-field parameters are fitted to the electrostatic potential as well as to accurate energies and forces generated by means of a hybrid method that combines solid-state density functional theory (DFT) calculations with an empirical van der Waals correction. All DFT calculations are carried out with the VASP program. The mathematical structure of the force field, the generation of reference data, the choice of the figure of merit, the optimization algorithm, and the parameter-refinement strategy are discussed in detail. The approach is applied to cyclohexane-1,4-dione, a small flexible ring. The tailor-made force field obtained for cyclohexane-1,4-dione is used to search for low-energy crystal packings in all 230 space groups with one molecule per asymmetric unit, and the most stable crystal structures are reoptimized in a second step with the hybrid method. The experimental crystal structure is found as the most stable predicted crystal structure both with the tailor-made force field and the hybrid method. The same methodology has also been applied successfully to the four compounds of the fourth CCDC blind test on crystal-structure prediction. For the five aforementioned compounds, the root-mean-square deviations between lattice energies calculated with the tailor-made force fields and the hybrid method range from 0.024 to 0.053 kcal/mol per atom around an average value of 0.034 kcal/mol per atom.

Porcelain enamel neutron absorbing material

DOEpatents

Iverson, Daniel C.

1990-01-01

A porcelain enamel composition as a neutron absorbing material can be prepared of a major proportion by weight of a cadmium compound and a minor proportion of compounds of boron, lithium and silicon. These compounds in the form of a porcelain enamel coating or layer on several alloys has been found to be particularly effective in enhancing the nuclear safety of equipment for use in the processing and storage of fissile material. The composition of the porcelain enamel coating can be tailored to match the coefficient of thermal expansion of the equipment to be coated and excellent coating adhesion can be achieved.

Porcelain enamel neutron absorbing material

DOEpatents

Iverson, Daniel C.

1990-02-06

A porcelain enamel composition as a neutron absorbing material can be prepared of a major proportion by weight of a cadmium compound and a minor proportion of compounds of boron, lithium and silicon. These compounds in the form of a porcelain enamel coating or layer on several alloys has been found to be particularly effective in enhancing the nuclear safety of equipment for use in the processing and storage of fissile material. The composition of the porcelain enamel coating can be tailored to match the coefficient of thermal expansion of the equipment to be coated and excellent coating adhesion can be achieved.

Sociopsychological tailoring to address colorectal cancer screening disparities: a randomized controlled trial.

PubMed

Jerant, Anthony; Kravitz, Richard L; Sohler, Nancy; Fiscella, Kevin; Romero, Raquel L; Parnes, Bennett; Tancredi, Daniel J; Aguilar-Gaxiola, Sergio; Slee, Christina; Dvorak, Simon; Turner, Charles; Hudnut, Andrew; Prieto, Francisco; Franks, Peter

2014-01-01

Interventions tailored to sociopsychological factors associated with health behaviors have promise for reducing colorectal cancer screening disparities, but limited research has assessed their impact in multiethnic populations. We examined whether an interactive multimedia computer program (IMCP) tailored to expanded health belief model sociopsychological factors could promote colorectal cancer screening in a multiethnic sample. We undertook a randomized controlled trial, comparing an IMCP tailored to colorectal cancer screening self-efficacy, knowledge, barriers, readiness, test preference, and experiences with a nontailored informational program, both delivered before office visits. The primary outcome was record-documented colorectal cancer screening during a 12-month follow-up period. Secondary outcomes included postvisit sociopsychological factor status and discussion, as well as clinician recommendation of screening during office visits. We enrolled 1,164 patients stratified by ethnicity and language (49.3% non-Hispanic, 27.2% Hispanic/English, 23.4% Hispanic/Spanish) from 26 offices around 5 centers (Sacramento, California; Rochester and the Bronx, New York; Denver, Colorado; and San Antonio, Texas). Adjusting for ethnicity/language, study center, and the previsit value of the dependent variable, compared with control patients, the IMCP led to significantly greater colorectal cancer screening knowledge, self-efficacy, readiness, test preference specificity, discussion, and recommendation. During the followup period, 132 (23%) IMCP and 123 (22%) control patients received screening (adjusted difference = 0.5 percentage points, 95% CI -4.3 to 5.3). IMCP effects did not differ significantly by ethnicity/language. Sociopsychological factor tailoring was no more effective than nontailored information in encouraging colorectal cancer screening in a multiethnic sample, despite enhancing sociopsychological factors and visit behaviors associated with screening. The

Tailored interphase structure for improved strength and energy absorption of composites

NASA Astrophysics Data System (ADS)

Gao, Xiao

Fiber reinforced polymeric composites are lightweight, high-strength and high impact-resistant materials used widely for various applications. It has been shown that the mechanical performance of composites are dependent on the interphase, a three-dimensional region of nanometer size in the vicinity of the fiber-matrix boundary that possesses properties different from those of either the fiber reinforcement or the matrix resin and governs the load transfer from matrix to fiber. This research conducts a systematic study on glass fiber-epoxy interphase structure by tailoring adhesion between constituents and the creation of textures to control strength and energy absorption through mechanical interlocking between glass fiber and epoxy matrix. Our objective is to establish the foundation for microstructural design and optimization of the composite's structural and impact performance. Two ways of roughening the glass fiber surface have been studied to create the mechanical interlocking between fiber and resin; the first technique involves forming in-situ islands on the glass fiber surface by using silane blends of Glycidoxypropyltrimethoxy silane (GPS) and Tetraethoxy silane (TEOS); the second technique applies a silane coupling agents based sizing with the incorporation of silica nanoparticles (Ludox TMA, 22 nm) onto the fiber surface. The microdroplet test was selected to characterize the influence of adhesion and mechanical interlocking effects on interphase properties of different sizing sized glass fiber reinforced epoxy systems. A suitable data reduction scheme enables the strength and specified energy absorbed due to debonding, dynamic sliding, and quasi-static sliding to be quantified. In order to validate the effect of tailored interphase structure, which is induced by creating mechanical interlocking between fiber and resin, on macroscopic composite properties, composite panels were made from these four different sizing sized glass fibers and tested using the

An analysis of health promotion materials for Dutch truck drivers: Off target and too complex?

PubMed

Boeijinga, Anniek; Hoeken, Hans; Sanders, José

2017-01-01

Despite various health promotion initiatives, unfavorable figures regarding Dutch truck drivers' eating behaviors, exercise behaviors, and absenteeism have not improved. The aim was to obtain a better understanding of the low level of effectiveness of current health interventions for Dutch truck drivers by examining to what extent these are tailored to the target group's particular mindset (focus of content) and health literacy skills (presentation of content). The article analyzes 21 health promotion materials for Dutch truck drivers using a two-step approach: (a) an analysis of the materials' focus, guided by the Health Action Process Approach; and (b) an argumentation analysis, guided by pragma-dialectics. The corpus analysis revealed: (a) a predominant focus on the motivation phase; and (b) in line with the aim of motivating the target group, a consistent use of pragmatic arguments, which were typically presented in an implicit way. The results indicate that existing health promotion materials for Dutch truck drivers are not sufficiently tailored to the target group's mindset and health literacy skills. Recommendations are offered to develop more tailored/effective health interventions targeting this high-risk, underserved occupational group.

Time series with tailored nonlinearities

NASA Astrophysics Data System (ADS)

Räth, C.; Laut, I.

2015-10-01

It is demonstrated how to generate time series with tailored nonlinearities by inducing well-defined constraints on the Fourier phases. Correlations between the phase information of adjacent phases and (static and dynamic) measures of nonlinearities are established and their origin is explained. By applying a set of simple constraints on the phases of an originally linear and uncorrelated Gaussian time series, the observed scaling behavior of the intensity distribution of empirical time series can be reproduced. The power law character of the intensity distributions being typical for, e.g., turbulence and financial data can thus be explained in terms of phase correlations.

An ecological momentary intervention for smoking cessation: The associations of just-in-time, tailored messages with lapse risk factors.

PubMed

Hébert, Emily T; Stevens, Elise M; Frank, Summer G; Kendzor, Darla E; Wetter, David W; Zvolensky, Michael J; Buckner, Julia D; Businelle, Michael S

2018-03-01

Smartphone apps can provide real-time, tailored interventions for smoking cessation. The current study examines the effectiveness of a smartphone-based smoking cessation application that assessed risk for imminent smoking lapse multiple times per day and provided messages tailored to current smoking lapse risk and specific lapse triggers. Participants (N=59) recruited from a safety-net hospital smoking cessation clinic completed phone-based ecological momentary assessments (EMAs) 5 times/day for 3 consecutive weeks (1week pre-quit, 2weeks post-quit). Risk for smoking lapse was estimated in real-time using a novel weighted lapse risk estimator. With each EMA, participants received messages tailored to current level of risk for imminent smoking lapse and self-reported presence of smoking urge, stress, cigarette availability, and motivation to quit. Generalized linear mixed model analyses determined whether messages tailored to specific lapse risk factors were associated with greater reductions in these triggers than messages not tailored to specific triggers. Overall, messages tailored to smoking urge, cigarette availability, or stress corresponded with greater reductions in those triggers than messages that were not tailored to specific triggers (p's=0.02 to <0.001). Although messages tailored to stress were associated with greater reductions in stress than messages not tailored to stress, the association was non-significant (p=0.892) when only moments of high stress were included in the analysis. Mobile technology can be used to conduct real-time smoking lapse risk assessment and provide tailored treatment content. Findings provide initial evidence that tailored content may impact users' urge to smoke, stress, and cigarette availability. Copyright © 2017 Elsevier Ltd. All rights reserved.

The tailored activity program (TAP) to address behavioral disturbances in frontotemporal dementia: a feasibility and pilot study.

PubMed

O'Connor, Claire M; Clemson, Lindy; Brodaty, Henry; Low, Lee-Fay; Jeon, Yun-Hee; Gitlin, Laura N; Piguet, Olivier; Mioshi, Eneida

2017-10-15

To explore the feasibility of implementing the Tailored Activity Program with a cohort of people with frontotemporal dementia and their carers (dyads). The Tailored Activity Program is an occupational therapy based intervention that involves working collaboratively with family carers and prescribes personalized activities for behavioral management in people with dementia. Twenty dyads randomized into the study (Tailored Activity Program: n = 9; Control: n = 11) were assessed at baseline and 4-months. Qualitative analyzes evaluated feasibility and acceptability of the program for the frontotemporal dementia cohort, and quantitative analyzes (linear mixed model analyzes, Spearman's rho correlations) measured the impact of the program on the dyads. The Tailored Activity Program was an acceptable intervention for the frontotemporal dementia dyads. Qualitative analyses identified five themes: "carer perceived benefits", "carer readiness to change", "strategies used by carer to engage person with dementia", "barriers to the Tailored Activity Program uptake/implementation", and "person with dementia engagement". Quantitative outcomes showed an overall reduction of behavioral symptoms (F 18.34  = 8.073, p = 0.011) and maintenance of functional performance in the person with dementia (F 18.03  = 0.375, p = 0.548). This study demonstrates the potential for using an activity-based intervention such as the Tailored Activity Program in frontotemporal dementia. Service providers should recognize that while people with frontotemporal dementia present with challenging issues, tailored therapies may support their function and reduce their behavioral symptoms. Implications for rehabilitation The Tailored Activity Program is an occupational therapy based intervention that involves prescribing personalized activities for behavioral management in dementia. The Tailored Activity Program is an acceptable and feasible intervention approach to address some of the

Innovative video tailoring for dietary change: final results of the Good for you! cluster randomized trial.

PubMed

Gans, Kim M; Risica, Patricia Markham; Dulin-Keita, Akilah; Mello, Jennifer; Dawood, Mahin; Strolla, Leslie O; Harel, Ofer

2015-10-07

Effective, low-cost approaches are needed to enhance dietary behavior change. While both video and tailoring technology have been effective interventions to improve diet, these approaches have never been combined to study the effectiveness of tailored videos. The purpose of this paper is to discuss the results of Good For You!, a randomized trial that tested the efficacy of innovative, individually tailored videos in helping worksite employees decrease dietary fat and increase fruit and vegetable (F&V) intake. Worksites were matched on approximate size, type of company and workforce composition and randomized to one of three experimental conditions: Non-Tailored written information (NT) (n = 14), Tailored Written information (TW) (n = 14), or Tailored Written + Tailored Video (TW + TV) (n = 15). Evaluation was conducted at baseline, 4 and 7 months. We used the NCI Fat Screener and an adapted Food Habits Questionnaire (FHQ) to estimate fat intake and fat-related behaviors, the NCI F&V Screener and F&V Habits Questionnaire (FVHQ) to measure F&V intake and behaviors. Generalized linear models were examined for all outcome measurements. 2525 worksite employees were recruited. At 4 months, dietary fat intake decreased significantly more for TW (-2.95 %) and TW + TV (-3.14%) compared with NT (-2.42%). FHQ scores decreased significantly more for TW + TV than the other two groups. Fruit intake increased the most for TW + TV compared to NT and TW. Both TW (1.30 cups) and TW + TV (1.59 cups) increased F&V intake significantly more than NT (0.78 cups). TW + TV showed the largest increase in F&V behaviors on the FVFQ. At 8 months, dietary fat change continued to be significantly better for TW + TV (-3.48%) than NT (3.01%). F&V intake increased significantly more for the TW + TV group (1.38 cups) compared to the NT group (1.04 cups) and FVHQ changes were significantly greater in TW + TV and TW than for NT. The tailored

New World Vistas: Air and Space Power for the 21st Century, Materials Volume.

DTIC Science & Technology

1996-06-01

derivatives from niche (non-silicon) materials: IR sensors, radars, lasers, and high - temperature , adverse-environment electronics. Investment in these...Develop metastable interstitial composites to create extremely high temperatures for destroying chemical biological warfare agents. " Explosives: 1...synthesize of high temperature materials that will be tailored for specific applications/ components. These materials will tend to have microstructures on

Experimental Investigations on Formability of Aluminum Tailor Friction Stir Welded Blanks in Deep Drawing Process

NASA Astrophysics Data System (ADS)

Kesharwani, R. K.; Panda, S. K.; Pal, S. K.

2015-02-01

In the present work, tailor friction stir welded blanks (TFSWBs) were fabricated successfully using 2.0-mm-thick AA5754-H22 and AA5052-H32 sheet metals with optimized tool design and process parameters. Taguchi L9 orthogonal array has been used to design the friction stir welding experiments, and the Grey relational analysis has been applied for the multi objective optimization in order to maximize the weld strength and total elongation reducing the surface roughness and energy consumption. The formability of the TFSWBs and parent materials was evaluated and compared in terms of limiting drawing ratio (LDR) using a conventional circular die. It was found that the formability of the TFSWBs was comparable with that of both the parent materials without failure in the weldment. A modified conical tractrix die (MCTD) was proposed to enhance the LDR of the TFSWBs. It was found that the formability was improved by 27% using the MCTD.

Electro-Analytical Study of Material Interfaces Relevant for Chemical Mechanical Planarization and Lithium Ion Batteries

NASA Astrophysics Data System (ADS)

Turk, Michael C.

This dissertation work involves two areas of experimental research, focusing specifically on the applications of electro-analytical techniques for interfacial material characterization. The first area of the work is centered on the evaluation and characterization of material components used for chemical mechanical planarization (CMP) in the fabrication of semiconductor devices. This part also represents the bulk of the projects undertaken for the present dissertation. The other area of research included here involves exploratory electrochemical studies of certain electrolyte and electrode materials for applications in the development of advanced lithium ion secondary batteries. The common element between the two areas of investigation is the technical approach that combines a broad variety of electro-analytical characterization techniques to examine application specific functions of the associated materials and devices. The CMP related projects concentrate on designing and evaluating materials for CMP slurries that would be useful in the processing of copper interconnects for the sub-22 nm technology node. Specifically, ruthenium and cobalt are nontraditional barrier materials currently considered for the new interconnects. The CMP schemes used to process the structures based on these metals involve complex surface chemistries of Ru, Co and Cu (used for wiring lines). The strict requirement of defect-control while maintaining material removal by precisely regulated tribo-corrosion complicates the designs of the CMP slurries needed to process these systems. Since Ru is electrochemically more noble than Cu, the surface regions of Cu assembled in contact with Ru tend to generate defects due to galvanic corrosion in the CMP environment. At the same time, Co is strongly reactive in the typical slurry environment and is prone to developing galvanic corrosion induced by Cu. The present work explores a selected class of alkaline slurry formulations aimed at reducing these

Native American Indian Adolescents: Response to a Culturally Tailored, School-Based Substance Abuse Intervention

ERIC Educational Resources Information Center

Patchell, Beverly A.

2011-01-01

Native American Indian adolescent substance abuse has been a longstanding health concern. There are few culturally tailored interventions for mild to moderate substance users. The purpose of this study was to measure the response of Native American Indian adolescents from the Plains tribal groups to a school-based culturally tailored substance…

Concurrent micromechanical tailoring and fabrication process optimization for metal-matrix composites

NASA Technical Reports Server (NTRS)

Morel, M.; Saravanos, D. A.; Chamis, Christos C.

1990-01-01

A method is presented to minimize the residual matrix stresses in metal matrix composites. Fabrication parameters such as temperature and consolidation pressure are optimized concurrently with the characteristics (i.e., modulus, coefficient of thermal expansion, strength, and interphase thickness) of a fiber-matrix interphase. By including the interphase properties in the fabrication process, lower residual stresses are achievable. Results for an ultra-high modulus graphite (P100)/copper composite show a reduction of 21 percent for the maximum matrix microstress when optimizing the fabrication process alone. Concurrent optimization of the fabrication process and interphase properties show a 41 percent decrease in the maximum microstress. Therefore, this optimization method demonstrates the capability of reducing residual microstresses by altering the temperature and consolidation pressure histories and tailoring the interphase properties for an improved composite material. In addition, the results indicate that the consolidation pressures are the most important fabrication parameters, and the coefficient of thermal expansion is the most critical interphase property.

Dynamic tailoring of surface plasmon polaritons through incident angle modulation.

PubMed

Qiu, Peizhen; Zhang, Dawei; Jing, Ming; Lu, Taiguo; Yu, Binbin; Zhan, Qiwen; Zhuang, Songlin

2018-04-16

Dynamic tailoring of the propagating surface plasmon polaritons (SPPs) through incident angle modulation is proposed and numerically demonstrated. The generation and tailoring mechanism of the SPPs are discussed. The relationship formula between the incident angle and the generated SPP wave vector direction is theoretically derived. The correctness of the formula is verified with three different approaches using finite difference time domain method. Using this formula, the generated SPP wave vector direction can be precisely modulated by changing the incident angle. The precise modulation results of two dimensional Bessel-like SPP beam and SPP bottle beam array are given. The results can deepen the understanding of the generation and modulation mechanism of the SPPs.

Conservatism implications of shock test tailoring for multiple design environments

NASA Technical Reports Server (NTRS)

Baca, Thomas J.; Bell, R. Glenn; Robbins, Susan A.

1987-01-01

A method for analyzing shock conservation in test specifications that have been tailored to qualify a structure for multiple design environments is discussed. Shock test conservation is qualified for shock response spectra, shock intensity spectra and ranked peak acceleration data in terms of an Index of Conservation (IOC) and an Overtest Factor (OTF). The multi-environment conservation analysis addresses the issue of both absolute and average conservation. The method is demonstrated in a case where four laboratory tests have been specified to qualify a component which must survive seven different field environments. Final judgment of the tailored test specification is shown to require an understanding of the predominant failure modes of the test item.

Development of a Tailored Thyroid Gland Phantom for Fine-Needle Aspiration Cytology by Three-Dimensional Printing.

PubMed

Baba, Masayuki; Matsumoto, Keitaro; Yamasaki, Naoya; Shindo, Hisakazu; Yano, Hiroshi; Matsumoto, Megumi; Otsubo, Ryota; John Lawn, Murray; Matsuo, Naoto; Yamamoto, Ikuo; Hidaka, Shigekazu; Nagayasu, Takeshi

Fine-needle aspiration cytology (FNAC) is a challenging and risky procedure for inexperienced clinicians to perform because of the proximity of the thyroid to the jugular veins, carotid arteries, and trachea. A phantom model for transfixion practice would help train clinicians in FNAC. To fabricate a tailored phantom with consideration for authenticity of size, touch, feel, and ultrasonographic (US) characteristics. A three-dimensional (3D) digital model of the human neck was reconstructed from computed tomography data of a subject. This model was used to create 3D-printed templates for various organs that require US visualization. The templates were injected with polymers that provided similar degrees of ultrasound permeability as the corresponding organs. For fabrication of each organ, the respective molds of organs, blood vessels, thyroid gland, and tumor were injected with the material. The fabricated components were then removed from the templates and colored. Individual components were then positioned in the neck mold, and agar gel was poured in. The complete phantom was then removed from the mold. Thereafter, 45 medical doctors and students performed ultrasound-guided FNAC using the phantom, following which they were queried regarding the value of the phantom. The structure, US characteristics, and elasticity of the phantom were similar to those of the human subject. In the survey, all 45 participants replied that they found the phantom useful for FNAC training, and 30 medical students professed increased interest in thyroid diseases after using the phantom. We successfully fabricated a tailored thyroid gland phantom for transfixion practice. As most of the phantom parts are injected in molds fabricated using a 3D printer, they can be easily reproduced once the molds are fabricated. This phantom is expected to serve as an effective and fully tailored training model for practicing thyroid gland transfixion. Copyright © 2017. Published by Elsevier Inc.

Differences in use and impact of computer-tailored dietary fat-feedback according to stage of change and education.

PubMed

Brug, J; van Assema, P

2000-06-01

Computer-tailored written nutrition education has been found to be more effective in motivating people to reduce their consumption of fat than traditional written information. The present study aimed to test whether this innovative nutrition education intervention is also suitable for people with low motivation to change and low education among a self-selected sample of 699 adults. Computer-tailored feedback proved to be more effective in motivating precontemplators to proceed towards fat reduction than general information. Higher appreciation and use of the computer-tailored fat-feedback was found among respondents in contemplation than in other stages. No difference in impact of computer-tailored fat-feedback on fat intake was found between educational groups. Respondents with low education were more positive about how interesting and how personally relevant the tailored letters were. It was concluded that printed computer-tailored fat-feedback can be applied successfully to motivate precontemplators and people with low education to (consider to) reduce their fat intake.

Generating User-Tailored Descriptions of Online Educational Resources

ERIC Educational Resources Information Center

Bental, Diana; Cawsey, Alison; Eddy, Bruce

2004-01-01

Tailored descriptions of online educational resources can support users searching for educational resources on the World Wide Web (WWW) by helping them to assess for themselves the relevance and suitability of each resource. Suitable descriptions can be derived from the online metadata stored with each resource. The descriptions take into account…

Developing Strategies for Waste Reduction by Means of Tailored Interventions in Santiago De Cuba

ERIC Educational Resources Information Center

Tobias, Robert; Brugger, Adrian; Mosler, Hans-Joachim

2009-01-01

This article introduces an approach to tailoring behavior-change campaigns to target populations using the example of solid waste reduction in Santiago de Cuba. Tailoring is performed in the following steps: (1) Psychological constructs are selected to detect problems in performing the target behavior, and data are gathered on these constructs.…

The Career Preparation Assessment (Tailored Versions): Results and Analyses from the 1998-1999 Cohort.

ERIC Educational Resources Information Center

McLaughlin, Daniel; Smorodin, Calla; Smorodin, Ted; Timms, Mike

A study was conducted to determine how the Career Preparation Assessment portfolio (CPA), tailored to be used in local school reform efforts, was implemented in 10 schools in 1998-99. The research was organized and reported using these four clusters of research questions: tailoring the CPA, implementation, student performance and assessment, and…

Cellulose-coupled graphene/polypyrrole composite electrodes containing conducting networks built by carbon fibers as wearable supercapacitors with excellent foldability and tailorability

NASA Astrophysics Data System (ADS)

Lyu, Shaoyi; Chang, Huanjun; Fu, Feng; Hu, La; Huang, Jingda; Wang, Siqun

2016-09-01

A paper-based wearable supercapacitor with excellent foldability and tailorability is fabricated from a chopped carbon fiber (CCF)-reinforced cellulose paper electrode material by coating with reduced graphene oxide (RGO) and polypyrrole (PPy) via in situ polymerization. The CCFs not only form an interpenetrating conducting network that acts as highly conductive electron transfer highways for the RGO/PPy layer in the paper electrode, but also endow the resulting electrode with an excellent areal capacitance of 363 mF cm-2 and a volumetric energy density of 0.28 mW h cm-3. Further, the CCFs give the electrode remarkable mechanical robustness, guaranteeing foldability and tailorability, with only slight loss of capacitance after repeated folding 600 times. Even after being subjected to severe cut-in fracture, the capacitance retention is up to 84%, indicating outstanding damage tolerance. The present study reveals a promising candidate for flexible wearable energy storage devices that are required to function in harsh environments.

Materials research for passive solar systems: Solid-state phase-change materials

NASA Astrophysics Data System (ADS)

Benson, D. K.; Webb, J. D.; Burrows, R. W.; McFadden, J. D. O.; Christensen, C.

1985-03-01

A set of solid-state phase-change materials is being evaluated for possible use in passive solar thermal energy storage systems. The most promising materials are organic solid solutions of pentaerythritol (C5H12O4), pentaglycerinve (C5H12O3), and neopentyl glycol (C5H12O2). Solid solution mixtures of these compounds can be tailored so that they exhibit solid-to-solid phase transformations at any desired temperature between 25 C and 188 C, and have latent heats of transformation etween 20 and 70 cal/g. Transformation temperatures, specific heats, and latent heats of transformation have been measured for a number of these materials. Limited cyclic experiments suggest that the solid solutions are stable. These phase-change materials exhibit large amounts of undercooling; however, the addition of certain nucleating agents as particulate dispersions in the solid phase-change material greatly reduces this effect. Computer simulations suggest that the use of an optimized solid-state phase-change material in a Trombe wall could provide better performance than a concrete Trombe wall four times thicker and nine times heavier.

Development of a New Method to Investigate the Dynamic Friction Behavior of Interfaces Using a Kolsky Tension Bar

DOE PAGES

Sanborn, B.; Song, B.; Nishida, E.

2017-11-02

In order to understand interfacial interaction of a bi-material during an impact loading event, the dynamic friction coefficient is one of the key parameters that must be characterized and quantified. In this study, a new experimental method to determine the dynamic friction coefficient between two metals was developed by using a Kolsky tension bar and a custom-designed friction fixture. Polyvinylidene fluoride (PVDF) force sensors were used to measure the normal force applied to the friction tribo pairs and the friction force was measured with conventional Kolsky tension bar method. To evaluate the technique, the dynamic friction coefficient between 4340 steelmore » and 7075-T6 aluminum was investigated at an impact speed of approximately 8 m/s. Additionally, the dynamic friction coefficient of the tribo pairs with varied surface roughness was also investigated. The data suggest that higher surface roughness leads to higher friction coefficients at the same speed of 8 m/s.« less

Porcelain enamel neutron absorbing material

DOEpatents

Iverson, D.C.

1987-11-20

A porcelain enamel composition as a neutron absorbing material can be prepared of a major proportion by weight of a cadmium compound and a minor proportion of compound of boron, lithium and silicon. These compounds in the form of a porcelain enamel coating or layer on several alloys has been found to be particularly effective in enhancing the nuclear safety of equipment for use in the processing and storage of fissile material. The composition of the porcelain enamel coating can be tailored to match the coefficient of thermal expansion of the equipment to be coated and excellent coating adhesion can be achieved. 2 figs.

Structural tailoring of advanced turboprops

NASA Technical Reports Server (NTRS)

Brown, K. W.; Hopkins, Dale A.

1988-01-01

The Structural Tailoring of Advanced Turboprops (STAT) computer program was developed to perform numerical optimization on highly swept propfan blades. The optimization procedure seeks to minimize an objective function defined as either: (1) direct operating cost of full scale blade or, (2) aeroelastic differences between a blade and its scaled model, by tuning internal and external geometry variables that must satisfy realistic blade design constraints. The STAT analysis system includes an aerodynamic efficiency evaluation, a finite element stress and vibration analysis, an acoustic analysis, a flutter analysis, and a once-per-revolution forced response life prediction capability. STAT includes all relevant propfan design constraints.

Structural tailoring of advanced turboprops (STAT): User's manual

NASA Technical Reports Server (NTRS)

Brown, K. W.

1991-01-01

This user's manual describes the Structural Tailoring of Advanced Turboprops program. It contains instructions to prepare the input for optimization, blade geometry and analysis, geometry generation, and finite element program control. In addition, a sample input file is provided as well as a section describing special applications (i.e., non-standard input).

Tailoring Interventions: Examining the Evidence and Identifying Gaps

ERIC Educational Resources Information Center

Gagliardi, Anna R.

2011-01-01

Introduction: Numerous population-based studies highlight the need to improve health care delivery and outcomes. Many single and combined interventions are available but their impact is limited and inconsistent. Tailoring may enhance their impact, but the best way to do so remains unclear. The purpose of this exploratory analysis was to identify…

37 CFR 401.5 - Modification and tailoring of clauses.

Code of Federal Regulations, 2013 CFR

2013-07-01

... sublicense foreign governments or international organizations pursuant to any existing treaty or... FIRMS UNDER GOVERNMENT GRANTS, CONTRACTS, AND COOPERATIVE AGREEMENTS § 401.5 Modification and tailoring... accordance with their own or applicable government-wide regulations such as the Federal Acquisition...

37 CFR 401.5 - Modification and tailoring of clauses.

Code of Federal Regulations, 2014 CFR

2014-07-01

... sublicense foreign governments or international organizations pursuant to any existing treaty or... FIRMS UNDER GOVERNMENT GRANTS, CONTRACTS, AND COOPERATIVE AGREEMENTS § 401.5 Modification and tailoring... accordance with their own or applicable government-wide regulations such as the Federal Acquisition...

37 CFR 401.5 - Modification and tailoring of clauses.

Code of Federal Regulations, 2012 CFR

2012-07-01

... sublicense foreign governments or international organizations pursuant to any existing treaty or... GOVERNMENT GRANTS, CONTRACTS, AND COOPERATIVE AGREEMENTS § 401.5 Modification and tailoring of clauses. (a... own or applicable government-wide regulations such as the Federal Acquisition Regulation. In grants...

37 CFR 401.5 - Modification and tailoring of clauses.

Code of Federal Regulations, 2011 CFR

2011-07-01

... sublicense foreign governments or international organizations pursuant to any existing treaty or... GOVERNMENT GRANTS, CONTRACTS, AND COOPERATIVE AGREEMENTS § 401.5 Modification and tailoring of clauses. (a... own or applicable government-wide regulations such as the Federal Acquisition Regulation. In grants...

Neurophysiologic Analysis of the Effects of Interactive Tailored Health Videos on Attention to Health Messages

ERIC Educational Resources Information Center

Lee, Jung A.

2011-01-01

Web-based tailored approaches hold much promise as effective means for delivering health education and improving public health. This study examines the effects of interactive tailored health videos on attention to health messages using neurophysiological changes measured by Electroencephalogram (EEG) and Electrocardiogram (EKG). Sixty-eight…

Biodegradable containers from green waste materials

NASA Astrophysics Data System (ADS)

Sartore, Luciana; Schettini, Evelia; Pandini, Stefano; Bignotti, Fabio; Vox, Giuliano; D'Amore, Alberto

2016-05-01

Novel biodegradable polymeric materials based on protein hydrolysate (PH), derived from waste products of the leather industry, and poly(ethylene glycol) diglycidyl ether (PEG) or epoxidized soybean oil (ESO) were obtained and their physico-chemical properties and mechanical behaviour were evaluated. Different processing conditions and the introduction of fillers of natural origin, as saw dust and wood flour, were used to tailor the mechanical properties and the environmental durability of the product. The biodegradable products, which are almost completely manufactured from renewable-based raw materials, look promising for several applications, particularly in agriculture for the additional fertilizing action of PH or in packaging.

The Use of Intervention Mapping to Develop a Tailored Web-Based Intervention, Condom-HIM

PubMed Central

2017-01-01

Background Many HIV (human immunodeficiency virus) prevention interventions are currently being implemented and evaluated, with little information published on their development. A framework highlighting the method of development of an intervention can be used by others wanting to replicate interventions or develop similar interventions to suit other contexts and settings. It provides researchers with a comprehensive development process of the intervention. Objective The objective of this paper was to describe how a systematic approach, intervention mapping, was used to develop a tailored Web-based intervention to increase condom use among HIV-positive men who have sex with men. Methods The intervention was developed in consultation with a multidisciplinary team composed of academic researchers, community members, Web designers, and the target population. Intervention mapping involved a systematic process of 6 steps: (1) needs assessment; (2) identification of proximal intervention objectives; (3) selection of theory-based intervention methods and practical strategies; (4) development of intervention components and materials; (5) adoption, implementation, and maintenance; and (6) evaluation planning. Results The application of intervention mapping resulted in the development of a tailored Web-based intervention for HIV-positive men who have sex with men, called Condom-HIM. Conclusions Using intervention mapping as a systematic process to develop interventions is a feasible approach that specifically integrates the use of theory and empirical findings. Outlining the process used to develop a particular intervention provides clarification on the conceptual use of experimental interventions in addition to potentially identifying reasons for intervention failures. PMID:28428162

The Cardiovascular Intervention Improvement Telemedicine Study (CITIES): Rationale for a Tailored Behavioral and Educational Pharmacist-Administered Intervention for Achieving Cardiovascular Disease Risk Reduction

PubMed Central

Zullig, Leah L.; Melnyk, S. Dee; Stechuchak, Karen M.; McCant, Felicia; Danus, Susanne; Oddone, Eugene; Bastian, Lori; Olsen, Maren; Edelman, David; Rakley, Susan; Morey, Miriam

2014-01-01

Abstract Background: Hypertension, hyperlipidemia, and diabetes are significant, but often preventable, contributors to cardiovascular disease (CVD) risk. Medication and behavioral nonadherence are significant barriers to successful hypertension, hyperlidemia, and diabetes management. Our objective was to describe the theoretical framework underlying a tailored behavioral and educational pharmacist-administered intervention for achieving CVD risk reduction. Materials and Methods: Adults with poorly controlled hypertension and/or hyperlipidemia were enrolled from three outpatient primary care clinics associated with the Durham Veterans Affairs Medical Center (Durham, NC). Participants were randomly assigned to receive a pharmacist-administered, tailored, 1-year telephone-based intervention or usual care. The goal of the study was to reduce the risk for CVD through a theory-driven intervention to increase medication adherence and improve health behaviors. Results: Enrollment began in November 2011 and is ongoing. The target sample size is 500 patients. Conclusions: The Cardiovascular Intervention Improvement Telemedicine Study (CITIES) intervention has been designed with a strong theoretical underpinning. The theoretical foundation and intervention are designed to encourage patients with multiple comorbidities and poorly controlled CVD risk factors to engage in home-based monitoring and tailored telephone-based interventions. Evidence suggests that clinical pharmacist-administered telephone-based interventions may be efficiently integrated into primary care for patients with poorly controlled CVD risk factors. PMID:24303930

A Web-Based and Print-Based Computer-Tailored Physical Activity Intervention for Prostate and Colorectal Cancer Survivors: A Comparison of User Characteristics and Intervention Use

PubMed Central

Bolman, Catherine; Peels, Denise Astrid; Volders, Esmee; de Vries, Hein; Lechner, Lilian

2017-01-01

Background Physical activity (PA) is beneficial in improving negative physical and psychological effects of cancer. The rapidly increasing number of cancer survivors, resulting from aging and improved cancer care, emphasizes the importance to develop and provide low cost, easy accessible PA programs. Such programs could be provided through the Internet, but that could result in the exclusion of cancer survivors not familiar with the Internet. Therefore, we developed a computer-tailored PA intervention for prostate and colorectal cancer survivors in which both Web-based and print materials are provided, and participants can choose their own preferred delivery mode. Objective The aim of this study was to assess participants’ characteristics related to delivery mode and use of intervention materials. Methods We studied characteristics of participants using Web-based and printed intervention materials in a randomized controlled trial (RCT). Prostate and colorectal cancer survivors recruited from hospitals were randomized to OncoActive (computer-tailored PA intervention) or a usual-care control group. OncoActive participants received both Web-based and printed materials. Participants were classified into initial print- or Web-based participants based on their preferred mode of completion of the first questionnaire, which was needed for the computer-tailored PA advice. Intervention material use during the remainder of the intervention was compared for initial print- or Web-based participants. Additionally, participants were classified into those using only print materials and those using Web-based materials. Differences in participant characteristics and intervention material use were studied through analysis of variance (ANOVAs), chi-square tests, and logistic regressions. Results The majority of the participants in the intervention group were classified as initial Web-based participants (170/249, 68.3%), and 84.9% (191/249) used Web-based intervention materials

A Web-Based and Print-Based Computer-Tailored Physical Activity Intervention for Prostate and Colorectal Cancer Survivors: A Comparison of User Characteristics and Intervention Use.

PubMed

Golsteijn, Rianne Henrica Johanna; Bolman, Catherine; Peels, Denise Astrid; Volders, Esmee; de Vries, Hein; Lechner, Lilian

2017-08-23

Physical activity (PA) is beneficial in improving negative physical and psychological effects of cancer. The rapidly increasing number of cancer survivors, resulting from aging and improved cancer care, emphasizes the importance to develop and provide low cost, easy accessible PA programs. Such programs could be provided through the Internet, but that could result in the exclusion of cancer survivors not familiar with the Internet. Therefore, we developed a computer-tailored PA intervention for prostate and colorectal cancer survivors in which both Web-based and print materials are provided, and participants can choose their own preferred delivery mode. The aim of this study was to assess participants' characteristics related to delivery mode and use of intervention materials. We studied characteristics of participants using Web-based and printed intervention materials in a randomized controlled trial (RCT). Prostate and colorectal cancer survivors recruited from hospitals were randomized to OncoActive (computer-tailored PA intervention) or a usual-care control group. OncoActive participants received both Web-based and printed materials. Participants were classified into initial print- or Web-based participants based on their preferred mode of completion of the first questionnaire, which was needed for the computer-tailored PA advice. Intervention material use during the remainder of the intervention was compared for initial print- or Web-based participants. Additionally, participants were classified into those using only print materials and those using Web-based materials. Differences in participant characteristics and intervention material use were studied through analysis of variance (ANOVAs), chi-square tests, and logistic regressions. The majority of the participants in the intervention group were classified as initial Web-based participants (170/249, 68.3%), and 84.9% (191/249) used Web-based intervention materials. Dropout was low (15/249, 6.0%) and differed

Tailored interventions to overcome identified barriers to change: effects on professional practice and health care outcomes

PubMed Central

Baker, Richard; Camosso-Stefinovic, Janette; Gillies, Clare; Shaw, Elizabeth J; Cheater, Francine; Flottorp, Signe; Robertson, Noelle

2014-01-01

Background In the previous version of this review, the effectiveness of interventions tailored to barriers to change was found to be uncertain. Objectives To assess the effectiveness of interventions tailored to address identified barriers to change on professional practice or patient outcomes. Search methods For this update, in addition to the EPOC Register and pending files, we searched the following databases without language restrictions, from inception until August 2007: MEDLINE, EMBASE, CINAHL, BNI and HMIC. We searched the National Research Register to November 2007. We undertook further searches to October 2009 to identify potentially eligible published or ongoing trials. Selection criteria Randomised controlled trials (RCTs) of interventions tailored to address prospectively identified barriers to change that reported objectively measured professional practice or healthcare outcomes in which at least one group received an intervention designed to address prospectively identified barriers to change. Data collection and analysis Two reviewers independently assessed quality and extracted data. We undertook quantitative and qualitative analyses. The quantitative analyses had two elements. We carried out a meta-regression to compare interventions tailored to address identified barriers to change with either no interventions or an intervention(s) not tailored to the barriers.We carried out heterogeneity analyses to investigate sources of differences in the effectiveness of interventions. These included the effects of: risk of bias, concealment of allocation, rigour of barrier analysis, use of theory, complexity of interventions, and the reported presence of administrative constraints. Main results We included 26 studies comparing an intervention tailored to address identified barriers to change to no intervention or an intervention(s) not tailored to the barriers. The effect sizes of these studies varied both across and within studies. Twelve studies provided

Ductile Binder Phase For Use With Almgb14 And Other Hard Ceramic Materials

DOEpatents

Cook, Bruce A.; Russell, Alan; Harringa, Joel

2005-07-26

This invention relates to a ductile binder phase for use with AlMgB14 and other hard materials. The ductile binder phase, a cobalt-manganese alloy, is used in appropriate quantities to tailor good hardness and reasonable fracture toughness for hard materials so they can be used suitably in industrial machining and grinding applications.

Nanomanufacturing : nano-structured materials made layer-by-layer.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cox, James V.; Cheng, Shengfeng; Grest, Gary Stephen

Large-scale, high-throughput production of nano-structured materials (i.e. nanomanufacturing) is a strategic area in manufacturing, with markets projected to exceed $1T by 2015. Nanomanufacturing is still in its infancy; process/product developments are costly and only touch on potential opportunities enabled by growing nanoscience discoveries. The greatest promise for high-volume manufacturing lies in age-old coating and imprinting operations. For materials with tailored nm-scale structure, imprinting/embossing must be achieved at high speeds (roll-to-roll) and/or over large areas (batch operation) with feature sizes less than 100 nm. Dispersion coatings with nanoparticles can also tailor structure through self- or directed-assembly. Layering films structured with thesemore » processes have tremendous potential for efficient manufacturing of microelectronics, photovoltaics and other topical nano-structured devices. This project is designed to perform the requisite R and D to bring Sandia's technology base in computational mechanics to bear on this scale-up problem. Project focus is enforced by addressing a promising imprinting process currently being commercialized.« less

Adaptation Criteria for the Personalised Delivery of Learning Materials: A Multi-Stage Empirical Investigation

ERIC Educational Resources Information Center

Thalmann, Stefan

2014-01-01

Personalised e-Learning represents a major step-change from the one-size-fits-all approach of traditional learning platforms to a more customised and interactive provision of learning materials. Adaptive learning can support the learning process by tailoring learning materials to individual needs. However, this requires the initial preparation of…

SraTailor: graphical user interface software for processing and visualizing ChIP-seq data.

PubMed

Oki, Shinya; Maehara, Kazumitsu; Ohkawa, Yasuyuki; Meno, Chikara

2014-12-01

Raw data from ChIP-seq (chromatin immunoprecipitation combined with massively parallel DNA sequencing) experiments are deposited in public databases as SRAs (Sequence Read Archives) that are publically available to all researchers. However, to graphically visualize ChIP-seq data of interest, the corresponding SRAs must be downloaded and converted into BigWig format, a process that involves complicated command-line processing. This task requires users to possess skill with script languages and sequence data processing, a requirement that prevents a wide range of biologists from exploiting SRAs. To address these challenges, we developed SraTailor, a GUI (Graphical User Interface) software package that automatically converts an SRA into a BigWig-formatted file. Simplicity of use is one of the most notable features of SraTailor: entering an accession number of an SRA and clicking the mouse are the only steps required to obtain BigWig-formatted files and to graphically visualize the extents of reads at given loci. SraTailor is also able to make peak calls, generate files of other formats, process users' own data, and accept various command-line-like options. Therefore, this software makes ChIP-seq data fully exploitable by a wide range of biologists. SraTailor is freely available at http://www.devbio.med.kyushu-u.ac.jp/sra_tailor/, and runs on both Mac and Windows machines. © 2014 The Authors Genes to Cells © 2014 by the Molecular Biology Society of Japan and Wiley Publishing Asia Pty Ltd.

Synthesis of visible light driven cobalt tailored Ag{sub 2}O/TiON nanophotocatalyst by reverse micelle processing for degradation of Eriochrome Black T

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hussain, Syed Tajammul, E-mail: dr_tajammul@yahoo.ca; Rashid; Department of Chemistry, Quaid-i-Azam University, Islamabad

2013-02-15

Graphical abstract: Cobalt tailored Ag{sub 2}O/TiON nanophotocatalyst is synthesized using reverse micelle technique and it showed extraordinary photocatalytic activity. Display Omitted Highlights: ► TiON/Ag{sub 2}O/Co nanophotocatalyst is synthesized using microemulsion technique. ► Low temperature anatase phase and outstanding photocatlytic activity is observed. ► Effect of temperature and inert atmosphere on materials phase is investigated. ► Homogeneous dopants distribution and oxygen vacancies are examined. ► Enhancement in surface area, quantum efficiency and optical properties is observed. -- Abstract: An ultra efficient cobalt tailored silver and nitrogen co-doped titania (TiON/Ag{sub 2}O/Co) visible nanophotocatalyst is successfully synthesized using modified reverse micelle processing. Composition,more » phase, distribution of dopants, functional group analysis, optical properties and morphology of synthesized materials are investigated by means of X-ray diffraction (XRD), transmission electron microscopy (TEM) based techniques and others. Charge states of titanium (Ti) and silver are explored through core-loss electron energy loss spectroscopy (EELS) analysis and X ray photoelectron spectroscopy (XPS). Our characterization results showed that the synthesized nanophotocatalyst consisted of anatase phased qausispherical nanoparticles that exhibited homogeneous distribution of dopants, large surface area, high quantum efficiency and enhanced optical properties. At lower content of doped Co ions, the TiON/Ag{sub 2}O responded with extraordinary photocatalytic properties. The cobalt tailored nanophotocatalyst showed remarkable activity against Eriochrome Black T (EBT). Moreover, comparative degradation behavior of EBT with TiON, Ag{sub 2}O/TiON and Co/Ag{sub 2}O/TiON is also investigated.« less

Tailored nanoporous coatings fabricated on conformable polymer substrates.

PubMed

Poxson, David J; Mont, Frank W; Cho, Jaehee; Schubert, E Fred; Siegel, Richard W

2012-11-01

Nanoporous coatings have become the subject of intense investigation, in part because they have been shown to have unique and tailorable physical properties that can depart greatly from their dense or macroscopic counterparts. Nanoporous coatings are frequently fabricated utilizing oblique-angle or glancing-angle physical vapor-phase deposition techniques. However, a significant limitation for such coatings exists; they are almost always deposited on smooth and rigid planar substrates, such as silicon and glass. This limitation greatly constrains the applicability, tailorability, functionality and even the economic viability, of such nanoporous coatings. Here, we report our findings on nanoporous/polymer composite systems (NPCS) fabricated by utilizing oblique-angle electron-beam methodology. These unique composite systems exhibit several favorable characteristics, namely, (i) fine-tuned control over coating nanoporosity and thickness, (ii) excellent adhesion between the nanoporous coating and polymer substrate, (iii) the ability to withstand significant and repeated bending, and (iv) the ability to be molded conformably on two and three-dimensional surfaces while closely retaining the composite system's designed nanoporous film structure and, hence, properties.

Analysis, design and elastic tailoring of composite rotor blades

NASA Technical Reports Server (NTRS)

Rehfield, Lawrence W.; Atilgan, Ali R.

1987-01-01

The development of structural models for composite rotor blades is summarized. The models are intended for use in design analysis for the purpose of exploring the potential of elastic tailoring. The research was performed at the Center for Rotary Wing Aircraft Technology.

Culturally Tailored Intervention for Rural African Americans With Type 2 Diabetes

PubMed Central

Utz, Sharon W.; Williams, Ishan C.; Jones, Randy; Hinton, Ivora; Alexander, Gina; Yan, Guofen; Moore, Cynthia; Blankenship, Jean; Steeves, Richard; Oliver, M. Norman

2013-01-01

Purpose The purpose of this pilot study was to evaluate a culturally tailored intervention for rural African Americans. Social Cognitive Theory provided the framework for the study. Methods Twenty-two participants were recruited and randomly assigned to either Group or Individual diabetes self-management (DSME). Group DSME included storytelling, hands-on activities, and problem-solving exercises. Individual DSME sessions focused on goal-setting and problem-solving strategies. Sessions were offered in an accessible community center over a 10-week period. Results Outcomes included glycosylated hemoglobin (A1C), self-care actions, self-efficacy level, goal attainment, and satisfaction with DSME. Participants in both Group and Individual DSME improved slightly over the 3-month period in self-care activities, A1C level, and goal attainment. Although differences were not statistically significant, trends indicate improved scores on dietary actions, foot care, goal attainment, and empowerment for those experiencing Group DSME. Conclusions The culturally tailored approach was well received by all participants. Improvements among those receiving Individual DSME may indicate that brief sessions using a culturally tailored approach could enhance self-care and glycemic control. Additional testing among more participants over a longer time period is recommended. PMID:18832290

Tailoring the chirality of light emission with spherical Si-based antennas.

PubMed

Zambrana-Puyalto, Xavier; Bonod, Nicolas

2016-05-21

Chirality of light is of fundamental importance in several enabling technologies with growing applications in life sciences, chemistry and photodetection. Recently, some attention has been focused on chiral quantum emitters. Consequently, optical antennas which are able to tailor the chirality of light emission are needed. Spherical nanoresonators such as colloids are of particular interest to design optical antennas since they can be synthesized at a large scale and they exhibit good optical properties. Here, we show that these colloids can be used to tailor the chirality of a chiral emitter. To this purpose, we derive an analytic formalism to model the interaction between a chiral emitter and a spherical resonator. We then compare the performances of metallic and dielectric spherical antennas to tailor the chirality of light emission. It is seen that, due to their strong electric dipolar response, metallic spherical nanoparticles spoil the chirality of light emission by yielding achiral fields. In contrast, thanks to the combined excitation of electric and magnetic modes, dielectric Si-based particles feature the ability to inhibit or to boost the chirality of light emission. Finally, it is shown that dual modes in dielectric antennas preserve the chirality of light emission.

Enabling high speed friction stir welding of aluminum tailor welded blanks

NASA Astrophysics Data System (ADS)

Hovanski, Yuri

Current welding technologies for production of aluminum tailor-welded blanks (TWBs) are utilized in low-volume and niche applications, and have yet to be scaled for the high-volume vehicle market. This study targeted further weight reduction, part reduction, and cost savings by enabling tailor-welded blank technology for aluminum alloys at high-volumes. While friction stir welding (FSW) has traditionally been applied at linear velocities less than one meter per minute, high volume production applications demand the process be extended to higher velocities more amenable to cost sensitive production environments. Unfortunately, weld parameters and performance developed and characterized at low to moderate welding velocities do not directly translate to high speed linear friction stir welding. Therefore, in order to facilitate production of high volume aluminum FSW components, parameters were developed with a minimum welding velocity of three meters per minute. With an emphasis on weld quality, welded blanks were evaluated for post-weld formability using a combination of numerical and experimental methods. Evaluation across scales was ultimately validated by stamping full-size production door inner panels made from dissimilar thickness aluminum tailor-welded blanks, which provided validation of the numerical and experimental analysis of laboratory scale tests.

Nanoscale tailor-made membranes for precise and rapid molecular sieve separation.

PubMed

Wang, Jing; Zhu, Junyong; Zhang, Yatao; Liu, Jindun; Van der Bruggen, Bart

2017-03-02

The precise and rapid separation of different molecules from aqueous, organic solutions and gas mixtures is critical to many technologies in the context of resource-saving and sustainable development. The strength of membrane-based technologies is well recognized and they are extensively applied as cost-effective, highly efficient separation techniques. Currently, empirical-based approaches, lacking an accurate nanoscale control, are used to prepare the most advanced membranes. In contrast, nanoscale control renders the membrane molecular specificity (sub-2 nm) necessary for efficient and rapid molecular separation. Therefore, as a growing trend in membrane technology, the field of nanoscale tailor-made membranes is highlighted in this review. An in-depth analysis of the latest advances in tailor-made membranes for precise and rapid molecule sieving is given, along with an outlook to future perspectives of such membranes. Special attention is paid to the established processing strategies, as well as the application of molecular dynamics (MD) simulation in nanoporous membrane design. This review will provide useful guidelines for future research in the development of nanoscale tailor-made membranes with a precise and rapid molecular sieve separation property.

Structural Integration of Sensors/Actuators by Laser Beam Melting for Tailored Smart Components

NASA Astrophysics Data System (ADS)

Töppel, Thomas; Lausch, Holger; Brand, Michael; Hensel, Eric; Arnold, Michael; Rotsch, Christian

2018-03-01

Laser beam melting (LBM), an additive laser powder bed fusion technology, enables the structural integration of temperature-sensitive sensors and actuators in complex monolithic metallic structures. The objective is to embed a functional component inside a metal part without losing its functionality by overheating. The first part of this paper addresses the development of a new process chain for bonded embedding of temperature-sensitive sensor/actuator systems by LBM. These systems are modularly built and coated by a multi-material/multi-layer thermal protection system of ceramic and metallic compounds. The characteristic of low global heat input in LBM is utilized for the functional embedding. In the second part, the specific functional design and optimization for tailored smart components with embedded functionalities are addressed. Numerical and experimental validated results are demonstrated on a smart femoral hip stem.

Mie resonances to tailor random lasers

NASA Astrophysics Data System (ADS)

García, P. D.; Ibisate, M.; Sapienza, R.; Wiersma, D. S.; López, C.

2009-07-01

In this paper, we present an optical characterization of photonic glass-based random lasers. We show how the resonant behavior of diffuse light transport through such systems can tailor the lasing emission when a gain medium is added to the glass. A DNA-based organic dye is used as gain medium. The resonances in the transport mean-free path influence the lasing wavelength of the random laser. The laser wavelength is therefore controlled by the sphere diameter. Furthermore, the existence of Mie resonances reduces the necessary pump energy to reach the lasing threshold.

[Tailored cranioplasty using CAD-CAM technology].

PubMed

Vitanovics, Dusán; Major, Ottó; Lovas, László; Banczerowski, Péter

2014-11-30

The majority of cranial defects are results of surgical intervention. The defect must be covered within resonable period of time usually after 4-6 week given the fact that the replacement of bone improve the brain circulation. Number of surgical techniques and materials are available to perform cranioplasty. Due to favorable properties we chosed ultra high molecular weight polyethylene as material. In this paper the authors show a procedure which allows tailored artificial bone replacement using state of art medical and engineering techniques. between 2004 and 2012, 19 patients were operated on cranial bone defect and a total of 22 3D custom-designed implants were implanted. The average age of patients was 35.4 years. In 12 patients we performed primary cranioplasty, while seven patients had the replacement at least once. Later the implants had to be removed due to infection or other causes (bone necrosis, fracture). All patients had native and bone-windowed 1 mm resolution CT. The 3D design was made using the original CT images and with design program. Computer controlled lathe was used to prepare a precise-fitting model. During surgery, the defect was exposed and the implant was fixed to normal bone using mini titanium plates and screws. All of our patients had control CT at 3, 6 and 12 months after surgery and at the same time neurological examination. Twenty-one polyethylene and one titanium implants were inserted. The average follow-up of the patients was 21.5 months, ranged from two to 96 months. We follow 12 patients (63.15%) more than one year. No intraoperative implant modifications had to be made. Each of the 22 implant exactly matched the bone defect proved by CT scan. No one of our patients reported aesthetic problems and we did not notice any kind of aesthetic complication. We had short term complication in three cases due to cranioplasty, subdural, epidural haemorrhage and skin defect. Polyethylene is in all respects suitable for primary and secondary

Web-Based Video-Coaching to Assist an Automated Computer-Tailored Physical Activity Intervention for Inactive Adults: A Randomized Controlled Trial.

PubMed

Alley, Stephanie; Jennings, Cally; Plotnikoff, Ronald C; Vandelanotte, Corneel

2016-08-12

Web-based physical activity interventions that apply computer tailoring have shown to improve engagement and behavioral outcomes but provide limited accountability and social support for participants. It is unknown how video calls with a behavioral expert in a Web-based intervention will be received and whether they improve the effectiveness of computer-tailored advice. The purpose of this study was to determine the feasibility and effectiveness of brief video-based coaching in addition to fully automated computer-tailored advice in a Web-based physical activity intervention for inactive adults. Participants were assigned to one of the three groups: (1) tailoring + video-coaching where participants received an 8-week computer-tailored Web-based physical activity intervention ("My Activity Coach") including 4 10-minute coaching sessions with a behavioral expert using a Web-based video-calling program (eg, Skype; n=52); (2) tailoring-only where participants received the same intervention without the coaching sessions (n=54); and (3) a waitlist control group (n=45). Demographics were measured at baseline, intervention satisfaction at week 9, and physical activity at baseline, week 9, and 6 months by Web-based self-report surveys. Feasibility was analyzed by comparing intervention groups on retention, adherence, engagement, and satisfaction using t tests and chi-square tests. Effectiveness was assessed using linear mixed models to compare physical activity changes between groups. A total of 23 tailoring + video-coaching participants, 30 tailoring-only participants, and 30 control participants completed the postintervention survey (83/151, 55.0% retention). A low percentage of tailoring + video-coaching completers participated in the coaching calls (11/23, 48%). However, the majority of those who participated in the video calls were satisfied with them (5/8, 71%) and had improved intervention adherence (9/11, 82% completed 3 or 4 modules vs 18/42, 43%, P=.01) and

Concurrent tailoring of fabrication process and interphase layer to reduce residual stresses in metal matrix composites

NASA Technical Reports Server (NTRS)

Saravanos, D. A.; Chamis, C. C.; Morel, M.

1991-01-01

A methodology is presented to reduce the residual matrix stresses in continuous fiber metal matrix composites (MMC) by optimizing the fabrication process and interphase layer characteristics. The response of the fabricated MMC was simulated based on nonlinear micromechanics. Application cases include fabrication tailoring, interphase tailoring, and concurrent fabrication-interphase optimization. Two composite systems, silicon carbide/titanium and graphite/copper, are considered. Results illustrate the merits of each approach, indicate that concurrent fabrication/interphase optimization produces significant reductions in the matrix residual stresses and demonstrate the strong coupling between fabrication and interphase tailoring.

Designing ICT Training Material for Chinese Language Arts Teachers.

ERIC Educational Resources Information Center

Lin, Janet Mei-Chuen; Wu, Cheng-Chih; Chen, Hsiu-Yen

The purpose of this research is to tailor the design of information and communications technology (ICT) training material to the needs of Chinese language arts teachers such that the training they receive will be conducive to effective integration of ICT into instruction. Eighteen experienced teachers participated in a Delphi-like survey that…

Tailored motivational message generation: A model and practical framework for real-time physical activity coaching.

PubMed

Op den Akker, Harm; Cabrita, Miriam; Op den Akker, Rieks; Jones, Valerie M; Hermens, Hermie J

2015-06-01

This paper presents a comprehensive and practical framework for automatic generation of real-time tailored messages in behavior change applications. Basic aspects of motivational messages are time, intention, content and presentation. Tailoring of messages to the individual user may involve all aspects of communication. A linear modular system is presented for generating such messages. It is explained how properties of user and context are taken into account in each of the modules of the system and how they affect the linguistic presentation of the generated messages. The model of motivational messages presented is based on an analysis of existing literature as well as the analysis of a corpus of motivational messages used in previous studies. The model extends existing 'ontology-based' approaches to message generation for real-time coaching systems found in the literature. Practical examples are given on how simple tailoring rules can be implemented throughout the various stages of the framework. Such examples can guide further research by clarifying what it means to use e.g. user targeting to tailor a message. As primary example we look at the issue of promoting daily physical activity. Future work is pointed out in applying the present model and framework, defining efficient ways of evaluating individual tailoring components, and improving effectiveness through the creation of accurate and complete user- and context models. Copyright © 2015 Elsevier Inc. All rights reserved.

Tribology study on TiB2+WSi2 composite against WC

NASA Astrophysics Data System (ADS)

Murthy, T. S. R. Ch.; Basha, M. M.; Sonber, J. K.; Singh, K.; Raju, K.; Sairam, K.; Nagaraj, A.; Majumdar, S.; Rao, G. V. S. Nageswara; Kain, Vivekanand

2018-04-01

Titanium diboride (TiB2) is one of the potential material for green energy applications such as neutron absorber in high temperature/advanced nuclear reactors, receiver materials for second generation concentrated solar power. We developed the process flow sheet for synthesis and consolidation of various series of TiB2 based materials in our laboratory. Amongst these, TiB2+WSi2 exhibited better sinterability and oxidation resistance properties. In the present work, tribology properties of TiB2+2.5%WSi2 composite was studied against WC-Co ball using different normal loads (5, 10 and 20 N) and frequencies (10, 15 Hz) under dry condition. Coefficient of friction (COF) and wear rate was measured at all test conditions. Wear mechanism was analyzed by microstructural characterization. It was found that COF is decreased from 0.46 to 0.36 with increasing load (5 to 20 N) at 15 Hz frequency; whereas at 10 Hz frequency COF is measured a constant average value of 0.49. The specific wear rate measured was minimum at 5 N load and 15 Hz frequency combination and was found to be 2.84×10-6 mm3/N m. The wear mechanisms identified during reciprocative sliding wear of composite were abrasion and surface tribo-oxidative reactions with delamination from tribo-zone.

Evaluation of a Tailored Direct-Mail Marketing Strategy for Recruiting the 19- to 23-Year-Old Market.

DTIC Science & Technology

1983-05-01

17AD-A12.9 860 EVALUATION OF A TAILORED DIRECT-MAIL MARKETING STRATEGY 1/ FOR RECRUITNG TH.U) WESAT INC ROCKVILLE MD K FERNANDES ET AL MAY 83 NPRDC...STANDARDS-1963-A EVALUATION OF A TAILORED DIRECT-MAIL MARKETING STRATEGY FOR RECRUITING THE 19- TO 23-YEAR-OLD MARKET APPRVEDFORPUBLIC RELE AnE [B...EVALUATION OF A TAILORED DIRECT-MAIL MARKETING STRATEGY FOR RECRUITING THE 19- TO 23-YEAR-OLD MARKET Kathleen Fernandes Navy Personnel Research and

Feasibility of a Tailored Intervention Targeting STD-Related Behaviors.

ERIC Educational Resources Information Center

Bellis, Jeffery M.; Grimely, Diane M.; Alexander, Leah R.

2002-01-01

Investigated whether high risk populations would be receptive to tailored, multimedia interventions to promote adoption of health-protective behaviors related to sexually transmitted disease (STD) prevention and control. Feedback from predominantly African American, urban participants aged 16-50 years, recruited from a STD clinic, indicated that…

Hybrid materials for optics and photonics.

PubMed

Lebeau, Benedicte; Innocenzi, Plinio

2011-02-01

The interest in organic-inorganic hybrids as materials for optics and photonics started more than 25 years ago and since then has known a continuous and strong growth. The high versatility of sol-gel processing offers a wide range of possibilities to design tailor-made materials in terms of structure, texture, functionality, properties and shape modelling. From the first hybrid material with optical functional properties that has been obtained by incorporation of an organic dye in a silica matrix, the research in the field has quickly evolved towards more sophisticated systems, such as multifunctional and/or multicomponent materials, nanoscale and self-assembled hybrids and devices for integrated optics. In the present critical review, we have focused our attention on three main research areas: passive and active optical hybrid sol-gel materials, and integrated optics. This is far from exhaustive but enough to give an overview of the huge potential of these materials in photonics and optics (254 references).

FSW of Aluminum Tailor Welded Blanks across Machine Platforms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hovanski, Yuri; Upadhyay, Piyush; Carlson, Blair

2015-02-16

Development and characterization of friction stir welded aluminum tailor welded blanks was successfully carried out on three separate machine platforms. Each was a commercially available, gantry style, multi-axis machine designed specifically for friction stir welding. Weld parameters were developed to support high volume production of dissimilar thickness aluminum tailor welded blanks at speeds of 3 m/min and greater. Parameters originally developed on an ultra-high stiffness servo driven machine where first transferred to a high stiffness servo-hydraulic friction stir welding machine, and subsequently transferred to a purpose built machine designed to accommodate thin sheet aluminum welding. The inherent beam stiffness, bearingmore » compliance, and control system for each machine were distinctly unique, which posed specific challenges in transferring welding parameters across machine platforms. This work documents the challenges imposed by successfully transferring weld parameters from machine to machine, produced from different manufacturers and with unique control systems and interfaces.« less

Web-Based Video-Coaching to Assist an Automated Computer-Tailored Physical Activity Intervention for Inactive Adults: A Randomized Controlled Trial

PubMed Central

Jennings, Cally; Plotnikoff, Ronald C; Vandelanotte, Corneel

2016-01-01

Background Web-based physical activity interventions that apply computer tailoring have shown to improve engagement and behavioral outcomes but provide limited accountability and social support for participants. It is unknown how video calls with a behavioral expert in a Web-based intervention will be received and whether they improve the effectiveness of computer-tailored advice. Objective The purpose of this study was to determine the feasibility and effectiveness of brief video-based coaching in addition to fully automated computer-tailored advice in a Web-based physical activity intervention for inactive adults. Methods Participants were assigned to one of the three groups: (1) tailoring + video-coaching where participants received an 8-week computer-tailored Web-based physical activity intervention (“My Activity Coach”) including 4 10-minute coaching sessions with a behavioral expert using a Web-based video-calling program (eg, Skype; n=52); (2) tailoring-only where participants received the same intervention without the coaching sessions (n=54); and (3) a waitlist control group (n=45). Demographics were measured at baseline, intervention satisfaction at week 9, and physical activity at baseline, week 9, and 6 months by Web-based self-report surveys. Feasibility was analyzed by comparing intervention groups on retention, adherence, engagement, and satisfaction using t tests and chi-square tests. Effectiveness was assessed using linear mixed models to compare physical activity changes between groups. Results A total of 23 tailoring + video-coaching participants, 30 tailoring-only participants, and 30 control participants completed the postintervention survey (83/151, 55.0% retention). A low percentage of tailoring + video-coaching completers participated in the coaching calls (11/23, 48%). However, the majority of those who participated in the video calls were satisfied with them (5/8, 71%) and had improved intervention adherence (9/11, 82% completed 3 or 4

Aerodynamic tailoring of the Learjet Model 60 wing

NASA Technical Reports Server (NTRS)

Chandrasekharan, Reuben M.; Hawke, Veronica M.; Hinson, Michael L.; Kennelly, Robert A., Jr.; Madson, Michael D.

1993-01-01

The wing of the Learjet Model 60 was tailored for improved aerodynamic characteristics using the TRANAIR transonic full-potential computational fluid dynamics (CFD) code. A root leading edge glove and wing tip fairing were shaped to reduce shock strength, improve cruise drag and extend the buffet limit. The aerodynamic design was validated by wind tunnel test and flight test data.

Heterocyclic Salt Synthesis and Rational Properties Tailoring (PREPRINT)

DTIC Science & Technology

2009-06-23

performance behavior can be tailored in a controlled manner, defines the objective of a pertinent synthesis effort. Achieving this objective by...the structure of the anion. To illustrate this premise, four general synthesis methods to synthesize heterocyclic salts, including several new binary...manner, defines the objective of a pertinent synthesis effort. Achieving this objective by introducing structural alterations in a neutral covalent

Tailoring double Fano profiles with plasmon-assisted quantum interference in hybrid exciton-plasmon system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Dongxing; Wu, Jiarui; Gu, Ying, E-mail: ygu@pku.edu.cn

2014-09-15

We propose tailoring of the double Fano profiles via plasmon-assisted quantum interference in a hybrid exciton-plasmon system. Tailoring is performed by the interference between two exciton channels interacting with a common localized surface plasmon. Using an applied field of low intensity, the absorption spectrum of the hybrid system reveals a double Fano lineshape with four peaks. For relatively large field intensity, a broad flat window in the absorption spectrum appears which results from the destructive interference between excitons. Because of strong constructive interference, this window vanishes as intensity is further increased. We have designed a nanometer bandpass optical filter formore » visible light based on tailoring of the optical spectrum. This study provides a platform for quantum interference that may have potential applications in ultracompact tunable quantum devices.« less

Tailoring polarization of electromagnetically induced transparency based on non-centrosymmetric metasurfaces

NASA Astrophysics Data System (ADS)

Li, Hai-ming; Xue, Feng

2017-09-01

In this manuscript, tailoring polarization of analogy of electromagnetically induced transparency (EIT-like) based on non-centrosymmetric metasurfaces has been numerically and experimentally demonstrated. The EIT-like metamaterial is composed of a rectangle ring and two cut wires. The rectangle ring and the cut wire are chosen as the bright mode and the quasi-dark mode, respectively. Under the incident electromagnetic wave excitation, a polarization insensitive EIT-like transmission window can be observed at specific polarization angles. Within the transmission window, the phase steeply changes, which leads to the large group index. Tailoring polarization of EIT-like metamaterial with large group index at specific polarization angles may have potential application in slow light devices.

Effectiveness of culturally tailored diabetes interventions for Asian immigrants to the United States: a systematic review.

PubMed

Joo, Jee Young

2014-01-01

The purpose of this systematic review is to evaluate the effectiveness of tailoring community-based diabetes intervention to Asian immigrant cultures. The Cochrane processes and Preferred Reporting Items for Systematic Reviews and Meta-Analyses recommendations guided this systematic review. PubMed, the Cumulative Index to Nursing and Allied Health Literature, Ovid, and PsycINFO were searched for analyses and syntheses of primary research published since 2000 that described interventions tailored for the cultures of Asian immigrants with diabetes. This search yielded a total of 9 articles published from 2005 to 2013. The Amsterdam-Maastricht Consensus List for Quality Assessment was used to assess the quality of the studies. Retrieved studies' populations were foreign-born adults >50 years of age with type 2 diabetes. The review revealed that culturally tailored diabetes programs are effective at improving patients' objectively measured clinical outcomes, in particular A1C levels, and psychobehavioral outcomes. Patients were also highly satisfied with bilingual health care providers and bilingual educational programs. There is strong evidence of the effectiveness of tailoring diabetes interventions to Asian immigrant populations' cultures. Further studies, including longitudinal studies and studies with rigorous research designs that subclassify Asian immigrants, are needed to encourage the implementation of culturally tailored diabetes intervention for this ethnic minority. © 2014 The Author(s).

Development of a computer-tailored physical activity intervention for prostate and colorectal cancer patients and survivors: OncoActive.

PubMed

Golsteijn, R H J; Bolman, C; Volders, E; Peels, D A; de Vries, H; Lechner, L

2017-06-26

Cancer and cancer treatment coincide with substantial negative physical, psychological and psychosocial problems. Physical activity (PA) can positively affect the negative effects of cancer and cancer treatment and thereby increase quality of life in CPS. Nevertheless, only a minority of CPS meet PA guidelines. We developed the OncoActive (OncoActief in Dutch) intervention: a computer-tailored PA program to stimulate PA in prostate and colorectal CPS, because to our knowledge there are only a few PA interventions for these specific cancer types in the Netherlands METHODS: The OncoActive intervention was developed through systematic adaptation of a proven effective, evidence-based, computer-tailored PA intervention for adults over fifty, called Active Plus. The Intervention Mapping (IM) protocol was used to guide the systematic adaptation. A literature study and interviews with prostate and colorectal CPS and health care professionals revealed that both general and cancer-specific PA determinants are important and should be addressed. Change objectives, theoretical methods and applications and the actual program content were adapted to address the specific needs, beliefs and cancer-related issues of prostate and colorectal CPS. Intervention participants received tailored PA advice three times, on internet and with printed materials, and a pedometer to set goals to improve PA. Pre- and pilot tests showed that the intervention was highly appreciated (target group) and regarded safe and feasible (healthcare professionals). The effectiveness of the intervention is being evaluated in a randomized controlled trial (RCT) (n = 428), consisting of an intervention group and a usual care waiting-list control group, with follow-up measurements at three, six and twelve months. Participants are recruited from seventeen hospitals and with posters, flyers and calls in several media. Using the Intervention Mapping protocol resulted in a systematically adapted, theory and evidence

The effect of tailored Web-based interventions on pain in adults: a systematic review protocol.

PubMed

Martorella, Géraldine; Gélinas, C; Bérubé, M; Boitor, M; Fredericks, S; LeMay, S

2016-04-12

Information technologies can facilitate the implementation of health interventions, especially in the case of widespread conditions such as pain. Tailored Web-based interventions have been recognized for health behavior change among diverse populations. However, none of the systematic reviews looking at Web-based interventions for pain management has specifically addressed the contribution of tailoring. The aims of this systematic review are to assess the effect of tailored Web-based pain management interventions on pain intensity and physical and psychological functions. Randomized controlled trials including adults suffering from any type of pain and involving Web-based interventions for pain management, using at least one of the three tailoring strategies (personalization, feedback, or adaptation), will be considered. The following types of comparisons will be carried out: tailored Web-based intervention with (1) usual care (passive control group), (2) face-to-face intervention, and (3) standardized Web-based intervention. The primary outcome will be pain intensity measured using a self-report measure such as the numeric rating scale (e.g., 0-10) or visual analog scale (e.g., 0-100). Secondary outcomes will include pain interference with activities and psychological well-being. A systematic review of English and French articles using MEDLINE, Embase, CINAHL, PsycINFO, Web of Science, and Cochrane Library will be conducted from January 2000 to December 2015. Eligibility assessment will be performed independently in an unblinded standardized manner by two reviewers. Extracted data will include the following: sample size, demographics, dropout rate, number and type of study groups, type of pain, inclusion and exclusion criteria, study setting, type of Web-based intervention, tailoring strategy, comparator, type of pain intensity measure, pain-related disability and psychological well-being outcomes, and times of measurement. Disagreements between reviewers at the

Structural Tailoring of Advanced Turboprops (STAT)

NASA Technical Reports Server (NTRS)

Brown, Kenneth W.

1988-01-01

This interim report describes the progress achieved in the structural Tailoring of Advanced Turboprops (STAT) program which was developed to perform numerical optimizations on highly swept propfan blades. The optimization procedure seeks to minimize an objective function, defined as either direct operating cost or aeroelastic differences between a blade and its scaled model, by tuning internal and external geometry variables that must satisfy realistic blade design constraints. This report provides a detailed description of the input, optimization procedures, approximate analyses and refined analyses, as well as validation test cases for the STAT program. In addition, conclusions and recommendations are summarized.

Models to Tailor Brain Stimulation Therapies in Stroke

PubMed Central

Plow, E. B.; Sankarasubramanian, V.; Cunningham, D. A.; Potter-Baker, K.; Varnerin, N.; Cohen, L. G.; Sterr, A.; Conforto, A. B.; Machado, A. G.

2016-01-01

A great challenge facing stroke rehabilitation is the lack of information on how to derive targeted therapies. As such, techniques once considered promising, such as brain stimulation, have demonstrated mixed efficacy across heterogeneous samples in clinical studies. Here, we explain reasons, citing its one-type-suits-all approach as the primary cause of variable efficacy. We present evidence supporting the role of alternate substrates, which can be targeted instead in patients with greater damage and deficit. Building on this groundwork, this review will also discuss different frameworks on how to tailor brain stimulation therapies. To the best of our knowledge, our report is the first instance that enumerates and compares across theoretical models from upper limb recovery and conditions like aphasia and depression. Here, we explain how different models capture heterogeneity across patients and how they can be used to predict which patients would best respond to what treatments to develop targeted, individualized brain stimulation therapies. Our intent is to weigh pros and cons of testing each type of model so brain stimulation is successfully tailored to maximize upper limb recovery in stroke. PMID:27006833

The Applications of Modern Nanoindentation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Buskirk, Caleb Griffith

2017-03-16

The TI-950 TriboIndenter is a nanoindentation device that obtains nanometer resolution material topography images using Scanning Probe Microscopy (SPM), modulus maps of material using nano-Dynamic Mechanical Analysis, and provides hardness measurements with a resolution of 0.2 nm. The instrument applies a force to a material through a sharp tip and used a transducer to measure the force a material applies back to the tip to derive information about the material. The information can be used to study the homogeneity of material surfaces as well as the homogeneity of the material as a function of depth and can lead to importantmore » information on the aging of the material as well as the consistency of the production of the material.« less

The Use of Intervention Mapping to Develop a Tailored Web-Based Intervention, Condom-HIM.

PubMed

Miranda, Joyal; Côté, José

2017-04-19

Many HIV (human immunodeficiency virus) prevention interventions are currently being implemented and evaluated, with little information published on their development. A framework highlighting the method of development of an intervention can be used by others wanting to replicate interventions or develop similar interventions to suit other contexts and settings. It provides researchers with a comprehensive development process of the intervention. The objective of this paper was to describe how a systematic approach, intervention mapping, was used to develop a tailored Web-based intervention to increase condom use among HIV-positive men who have sex with men. The intervention was developed in consultation with a multidisciplinary team composed of academic researchers, community members, Web designers, and the target population. Intervention mapping involved a systematic process of 6 steps: (1) needs assessment; (2) identification of proximal intervention objectives; (3) selection of theory-based intervention methods and practical strategies; (4) development of intervention components and materials; (5) adoption, implementation, and maintenance; and (6) evaluation planning. The application of intervention mapping resulted in the development of a tailored Web-based intervention for HIV-positive men who have sex with men, called Condom-HIM. Using intervention mapping as a systematic process to develop interventions is a feasible approach that specifically integrates the use of theory and empirical findings. Outlining the process used to develop a particular intervention provides clarification on the conceptual use of experimental interventions in addition to potentially identifying reasons for intervention failures. ©Joyal Miranda, José Côté. Originally published in JMIR Public Health and Surveillance (http://publichealth.jmir.org), 19.04.2017.

Tailoring of the partial magnonic gap in three-dimensional magnetoferritin-based magnonic crystals

NASA Astrophysics Data System (ADS)

Mamica, S.

2013-07-01

We investigate theoretically the use of magnetoferritin nanoparticles, self-assembled in the protein crystallization process, as the basis for the realization of 3D magnonic crystals in which the interparticle space is filled with a ferromagnetic material. Using the plane wave method we study the dependence of the width of the partial band gap and its central frequency on the total magnetic moment of the magnetoferritin core and the lattice constant of the magnetoferritin crystal. We show that by adjusting the combination of these two parameters the partial gap can be tailored in a wide frequency range and shifted to sub-terahertz frequencies. Moreover, the difference in the width of the partial gap for spin waves propagating in planes parallel and perpendicular to the external field allows for switching on and off the partial magnonic gap by changing the direction of the applied field.

Methods of producing cermet materials and methods of utilizing same

DOEpatents

Kong, Peter C [Idaho Falls, ID

2008-12-30

Methods of fabricating cermet materials and methods of utilizing the same such as in filtering particulate and gaseous pollutants from internal combustion engines having intermetallic and ceramic phases. The cermet material may be made from a transition metal aluminide phase and an alumina phase. The mixture may be pressed to form a green compact body and then heated in a nitrogen-containing atmosphere so as to melt aluminum particles and form the cermet. Filler materials may be added to increase the porosity or tailor the catalytic properties of the cermet material. Additionally, the cermet material may be reinforced with fibers or screens. The cermet material may also be formed so as to pass an electrical current therethrough to heat the material during use.

Methods of fabricating cermet materials and methods of utilizing same

DOEpatents

Kong, Peter C.

2006-04-04

Methods of fabricating cermet materials and methods of utilizing the same such as in filtering particulate and gaseous pollutants from internal combustion engines having intermetallic and ceramic phases. The cermet material may be made from a transition metal aluminide phase and an aluminia phase. The mixture may be pressed to form a green compact body and then heated in a nitrogen-containing atmosphere so as to melt aluminum particles and form the cermet. Filler materials may be added to increase the porosity or tailor the catalytic properties of the cermet material. Additionally, the cermet material may be reinforced with fibers or screens. The cermet material may also be formed so as to pass an electrical current therethrough to heat the material during use.

Preventing the obesity epidemic by second generation tailored health communication: an interdisciplinary review.

PubMed

Enwald, Heidi Päivyt Karoliina; Huotari, Maija-Leena Aulikki

2010-06-28

The prevention of obesity and health concerns related to obesity are major challenges worldwide. The use of eHealth communication and the tailoring of information delivered via the Internet at the individual level may increase the effectiveness of interventions. Mastering behaviors related to nutrition, physical activity, and weight management are the main issues in preventing obesity, and the need for interdisciplinary knowledge within this area is obvious. The objectives were to review the literature on tailored health communication and to present an interdisciplinary analysis of studies on "second" generation tailored interventions aimed at behavior change in nutrition, physical activity, or weight management. A literature search was conducted of the main electronic information sources on health communication. Selection criteria were defined, and 23 intervention studies were selected. The content analysis focused on the following: study designs, objectives of behavior change, target groups, sample sizes, study lengths, attrition rates, theories applied, intervention designs, computer-based channels used, statistically significant outcomes from the perspective of tailoring, and possible biases of the studies. However, this was not a structured meta-analysis and cannot be replicated as such. Of the 23 studies, 21 were randomized controlled trials, and all focused on behavior change: 10 studies focused on behavior change in nutrition, 7 on physical activity, 2 on nutrition and physical activity, and 4 on weight management. The target groups and the number of participants varied: 8 studies included more than 500 participants, and 6 studies included less than 100. Most studies were short; the duration of 20 studies was 6 months or less. The Transtheoretical Model was applied in 14 of the 23 studies, and feedback as a tailoring mechanism was used in addition to an Internet site (or program) in 15 studies and in addition to email in 11 studies. Self-reporting was used

New Imidazole-based High Nitrogen Energetic Materials

NASA Astrophysics Data System (ADS)

Windler, G. Kenneth; Leonard, Philip; Schulze, Maxwell; Hartline, Ernest

2017-06-01

Energetic materials derive their power from energy release, usually in the form of gaseous products. The type and quantity of these products contribute to performance and detonation parameters. In particular, high-nitrogen materials produce large quantities of elemental nitrogen, and can be tuned via molecular structure for suitability as propellants (gas generators) or explosives. In this work, the five-membered nitrogen heterocycle imidazole is used as a substrate for a variety of high-nitrogen materials. Substitution of the imidazole ring directly with nitro-, azido-, diazo-, and tetrazole moieties allows for tunable properties of the resultant energetic material. Properties can be further tailored by salt formation at the acidic proton(s) on the molecules. The various combinations of these derivatives are presented, along with the substitution effects on physical, chemical, and explosive properties.

Numerical analysis of tailored sheets to improve the quality of components made by SPIF

NASA Astrophysics Data System (ADS)

Gagliardi, Francesco; Ambrogio, Giuseppina; Cozza, Anna; Pulice, Diego; Filice, Luigino

2018-05-01

In this paper, the authors pointed out a study on the profitable combination of forming techniques. More in detail, the attention has been put on the combination of the single point incremental forming (SPIF) and, generally, speaking, of an additional process that can lead to a material thickening on the initial blank considering the local thinning which the sheets undergo at. Focalizing the attention of the research on the excessive thinning of parts made by SPIF, a hybrid approach can be thought as a viable solution to reduce the not homogeneous thickness distribution of the sheet. In fact, the basic idea is to work on a blank previously modified by a deformation step performed, for instance, by forming, additive or subtractive processes. To evaluate the effectiveness of this hybrid solution, a FE numerical model has been defined to analyze the thickness variation on tailored sheets incrementally formed optimizing the material distribution according to the shape to be manufactured. Simulations based on the explicit formulation have been set up for the model implementation. The mechanical properties of the sheet material have been taken in literature and a frustum of cone as benchmark profile has been considered for the performed analysis. The outcomes of numerical model have been evaluated in terms of both maximum thinning and final thickness distribution. The feasibility of the proposed approach will be deeply detailed in the paper.

Tailoring Small IT Projects in the Project Planning Phase

ERIC Educational Resources Information Center

Mulhearn, Michael F.

2011-01-01

Project management (PM) and systems engineering (SE) are essential skills in information technology (IT). There is an abundance of information available detailing the comprehensive bodies of knowledge, standards, and best practices. Despite the volume of information, there is surprisingly little information about how to tailor PM and SE tasks for…

Self-Assembled, Iridescent, Crustacean-Mimetic Nanocomposites with Tailored Periodicity and Layered Cuticular Structure.

PubMed

Wang, Baochun; Walther, Andreas

2015-11-24

Natural high-performance materials inspire the pursuit of ordered hard/soft nanocomposite structures at high fractions of reinforcements and with balanced molecular interactions. Herein, we develop a facile, waterborne self-assembly pathway to mimic the multiscale cuticle structure of the crustacean armor by combining hard reinforcing cellulose nanocrystals (CNCs) with soft poly(vinyl alcohol) (PVA). We show iridescent CNC nanocomposites with cholesteric liquid-crystal structure, in which different helical pitches and photonic band gaps can be realized by varying the CNC/PVA ratio. We further show that multilayered crustacean-mimetic materials with tailored periodicity and layered cuticular structure can be obtained by sequential preparation pathways. The transition from a cholesteric to a disordered structure occurs for a critical polymer concentration. Correspondingly, we find a transition from stiff and strong mechanical behavior to materials with increasing ductility. Crack propagation studies using scanning electron microscopy visualize the different crack growth and toughening mechanisms inside cholesteric nanocomposites as a function of the interstitial polymer content for the first time. Different extents of crack deflection, layered delamination, ligament bridging, and constrained microcracking can be observed. Drawing of highly plasticized films sheds light on the mechanistic details of the transition from a cholesteric/chiral nematic to a nematic structure. The study demonstrates how self-assembly of biobased CNCs in combination with suitable polymers can be used to replicate a hierarchical biological structure and how future design of these ordered multifunctional nanocomposites can be optimized by understanding mechanistic details of deformation and fracture.

Effects of tailored message education about breast cancer risk appraisal for obese Korean women.

PubMed

Park, Somi; Chung, ChaeWeon; Cochrane, Barbara B

2013-11-01

To examine the effects of tailored message education about breast cancer risk in obese Korean women. Pretest/post-test with two comparison treatments. Rural community settings in South Korea. Non-random sample of 64 obese women. Based on the Health Belief Model, tailored message education involved a one-session individual approach addressing cognitive, emotional, and behavioral domains. The comparison group received a one-time standard education group session. Data on breast cancer risk factors and mammography findings were recorded. Knowledge, awareness, emotional barriers, self-efficacy, and intent to screen and prevent breast cancer. Compared to standard education, tailored message education showed significantly higher score changes on awareness of personal risk (F = 5.21, p < 0.05), self-efficacy for breast self-examination (BSE) (F = 5.16, p < 0.001), intent to perform BSE (F = 6.24, p < 0.05), intent to have mammography (F = 5.45, p < 0.05), and intent to prevent breast cancer with eating habits (F = 7.28, p < 0.05) and exercising (F = 12.51, p < 0.001). Individually tailored education effectively enhanced awareness of personal risk for breast cancer, self-efficacy for BSE, and intent to screen and prevent breast cancer. Tailored message education targeting breast cancer and risk associated with obesity is useful in breast cancer screening education. Future studies should incorporate individualized messages on nutrition, exercise, and cultural barriers to reduce breast cancer risk in obese women. Individual educational strategies can effectively enhance breast cancer prevention and early screening. Public and preventive education should include a focus on cultural, cognitive, and emotional domains. For obese women, a heightened awareness and self-efficacy may influence screening behaviors.

Tailoring Materials for Mottronics: Excess Oxygen Doping of a Prototypical Mott Insulator.

PubMed

Scheiderer, Philipp; Schmitt, Matthias; Gabel, Judith; Zapf, Michael; Stübinger, Martin; Schütz, Philipp; Dudy, Lenart; Schlueter, Christoph; Lee, Tien-Lin; Sing, Michael; Claessen, Ralph

2018-05-07

The Mott transistor is a paradigm for a new class of electronic devices-often referred to by the term Mottronics-which are based on charge correlations between the electrons. Since correlation-induced insulating phases of most oxide compounds are usually very robust, new methods have to be developed to push such materials right to the boundary to the metallic phase in order to enable the metal-insulator transition to be switched by electric gating. Here, it is demonstrated that thin films of the prototypical Mott insulator LaTiO 3 grown by pulsed laser deposition under oxygen atmosphere are readily tuned by excess oxygen doping across the line of the band-filling controlled Mott transition in the electronic phase diagram. The detected insulator to metal transition is characterized by a strong change in resistivity of several orders of magnitude. The use of suitable substrates and capping layers to inhibit oxygen diffusion facilitates full control of the oxygen content and renders the films stable against exposure to ambient conditions. These achievements represent a significant advancement in control and tuning of the electronic properties of LaTiO 3+ x thin films making it a promising channel material in future Mottronic devices. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Enhancing caregivers' understanding of dementia and tailoring activities in frontotemporal dementia: two case studies.

PubMed

O'Connor, Claire M; Clemson, Lindy; Brodaty, Henry; Gitlin, Laura N; Piguet, Olivier; Mioshi, Eneida

2016-01-01

The purpose of this study is to describe the intervention process and results of the Tailored Activities Program (TAP) in two people diagnosed with Frontotemporal Dementia (FTD). TAP is an occupational therapy (OT) community-based intervention program that prescribes personalised activities to reduce difficult behaviours of dementia. The OT works with carers over a 4-month period (assessment, activity prescription and generalisation of strategies). Study measures were collected (blind researcher) pre- and post-intervention: cognition, functional disability, behavioural symptoms and Caregiver Confidence and Vigilance. A 51-year-old woman with behavioural-variant FTD could consistently engage in more activities post-intervention, with scores indicating improvements to behaviour, function and caregiver confidence. A 63-year-old man with semantic variant FTD engaged well in the prescribed activities, with scores reflecting reduced carer distress regarding challenging behaviours and improved caregiver vigilance. TAP is efficacious in FTD, allowing for differences in approach for FTD subtype, where behavioural symptoms are very severe and pervasive. The Tailored Activities Program is an intervention which can be tailored to account for unique behavioural and language profiles inherent across frontotemporal dementia (FTD) subtypes. Maintaining a flexible approach when applying an intervention in FTD allows for tailoring to individual case variability within FTD subtypes.

Effects of tailoring ingredients in auditory persuasive health messages on fruit and vegetable intake.

PubMed

Elbert, Sarah P; Dijkstra, Arie; Rozema, Andrea D

2017-07-01

Health messages can be tailored by applying different tailoring ingredients, among which personalisation, feedback and adaptation. This experiment investigated the separate effects of these tailoring ingredients on behaviour in auditory health persuasion. Furthermore, the moderating effect of self-efficacy was assessed. The between-participants design consisted of four conditions. A generic health message served as a control condition; personalisation was applied using the recipient's first name, feedback was given on the personal state, or the message was adapted to the recipient's value. The study consisted of a pre-test questionnaire (measuring fruit and vegetable intake and perceived difficulty of performing these behaviours, indicating self-efficacy), exposure to the auditory message and a follow-up questionnaire measuring fruit and vegetable intake two weeks after message exposure (n = 112). ANCOVAs showed no main effect of condition on either fruit or vegetable intake, but a moderation was found on vegetable intake: When self-efficacy was low, vegetable intake was higher after listening to the personalisation message. No significant differences between the conditions were found when self-efficacy was high. Individuals with low self-efficacy seemed to benefit from incorporating personalisation, but only regarding vegetable consumption. This finding warrants further investigation in tailoring research.

What's in a Surname? Physique, Aptitude, and Sports Type Comparisons between Tailors and Smiths.

PubMed

Voracek, Martin; Rieder, Stephan; Stieger, Stefan; Swami, Viren

2015-01-01

Combined heredity of surnames and physique, coupled with past marriage patterns and trade-specific physical aptitude and selection factors, may have led to differential assortment of bodily characteristics among present-day men with specific trade-reflecting surnames (Tailor vs. Smith). Two studies reported here were partially consistent with this genetic-social hypothesis, first proposed by Bäumler (1980). Study 1 (N = 224) indicated significantly higher self-rated physical aptitude for prototypically strength-related activities (professions, sports, hobbies) in a random sample of Smiths. The counterpart effect (higher aptitude for dexterity-related activities among Tailors) was directionally correct, but not significant, and Tailor-Smith differences in basic physique variables were nil. Study 2 examined two large total-population-of-interest datasets (Austria/Germany combined, and UK: N = 7001 and 20,532) of men's national high-score lists for track-and-field events requiring different physiques. In both datasets, proportions of Smiths significantly increased from light-stature over medium-stature to heavy-stature sports categories. The predicted counterpart effect (decreasing prevalences of Tailors along these categories) was not supported. Related prior findings, the viability of possible alternative interpretations of the evidence (differential positive selection for trades and occupations, differential endogamy and assortative mating patterns, implicit egotism effects), and directions for further inquiry are discussed in conclusion.

Post-Secondary Vocational Home Economics Instructional Materials Needs Assessment Project: State-of-the-Art and Final Report.

ERIC Educational Resources Information Center

Glosson, Linda R.; Bowers, Candice H.

A Texas project assessed postsecondary vocational home economics instructors' needs for instructional media and materials as well as the need for training in the development of curriculum materials. Relevant post-secondary programs identified were child development, food service/dietetics, fashion design/tailoring, and interior design. In…

Environment Conscious Ceramics (Ecoceramics): An Eco-Friendly Route to Advanced Ceramic Materials

NASA Technical Reports Server (NTRS)

Singh, M.

2001-01-01

Environment conscious ceramics (Ecoceramics) are a new class of materials, which can be produced with renewable natural resources (wood) or wood wastes (wood sawdust). This technology provides an eco-friendly route to advanced ceramic materials. Ecoceramics have tailorable properties and behave like ceramic materials manufactured by conventional approaches. Silicon carbide-based ecoceramics have been fabricated by reactive infiltration of carbonaceous preforms by molten silicon or silicon-refractory metal alloys. The fabrication approach, microstructure, and mechanical properties of SiC-based ecoceramics are presented.

Technical Knowledge and Skills Development in the Informal Sector in Kenya: The Case of Custom Tailors

ERIC Educational Resources Information Center

Apunda, Edwinah Amondi; de Klerk, Helena M.; Ogina, Teresa

2017-01-01

Custom tailors working in the informal sector in Nairobi, Kenya, mainly acquire technical skills through undertaking traditional apprenticeships (TAs). However, most of these tailors are semi-skilled, produce low-quality products and are often poorer than their formally trained counterparts. This qualitative case study explores the aspects of…

Internet provision of tailored advice on falls prevention activities for older people: a randomized controlled evaluation.

PubMed

Yardley, Lucy; Nyman, Samuel R

2007-06-01

Falls are very common in older persons and can result in substantial disability and distress. By undertaking strength and balance training (SBT) exercises, older people can reduce their risk of falling. The Internet offers a potentially cost-effective means of disseminating information about SBT to older people and their carers. A particular advantage of using the Internet for this purpose is that the advice given can be 'tailored' to the needs of the individual. This study used a randomized controlled design to evaluate an interactive web-based program that tailored advice about undertaking SBT activities. The participants were 280 people with an age range of 65-97 years recruited by advertising the website by email and the Internet. Those randomized to the tailored advice were presented with advice tailored to their personal self-rated balance capabilities, health problems and activity preferences. Those in the control group were presented with all the advice from which the tailored advice was selected. After reading the advice, those in the tailored advice group (n = 144) had more positive attitudes (p < 0.01) than those in the control group (n = 136), reporting greater perceived relevance of the SBT activities, greater confidence in the ability to carry them out, and hence stronger intentions to undertake the activities. This study provides an initial indication that an interactive website might offer a cost-effective way to provide personalized advice to some older people. Further research is required to determine whether website-based advice on falls prevention changes behavior as well as intentions and whether the advice needs to be supplemented by other forms of support.

Experimental Investigation of Fibre Reinforced Composite Materials Under Impact Load

NASA Astrophysics Data System (ADS)

Koppula, Sravani; Kaviti, Ajay kumar; Namala, Kiran kumar

2018-03-01

Composite materials are extensively used in various engineering applications. They have very high flexibility design which allows prescribe tailoring of material properties by lamination of composite fibres with reinforcement of resin to it. Complex failure condition prevail in the composite materials under the action of impact loads, major modes of failure in composite may include matrix cracking, fibre matrix, fibre breakage, de-bonding or de- lamination between composite plies. This paper describes the mechanical properties of glass fibre reinforced composite material under impact loading conditions through experimental setup. Experimental tests are performed according to ASTM standards using impact testing machines like Charpy test, computerized universal testing machine.

Computationally guided discovery of thermoelectric materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gorai, Prashun; Stevanović, Vladan; Toberer, Eric S.

The potential for advances in thermoelectric materials, and thus solid-state refrigeration and power generation, is immense. Progress so far has been limited by both the breadth and diversity of the chemical space and the serial nature of experimental work. In this Review, we discuss how recent computational advances are revolutionizing our ability to predict electron and phonon transport and scattering, as well as materials dopability, and we examine efficient approaches to calculating critical transport properties across large chemical spaces. When coupled with experimental feedback, these high-throughput approaches can stimulate the discovery of new classes of thermoelectric materials. Within smaller materialsmore » subsets, computations can guide the optimal chemical and structural tailoring to enhance materials performance and provide insight into the underlying transport physics. Beyond perfect materials, computations can be used for the rational design of structural and chemical modifications (such as defects, interfaces, dopants and alloys) to provide additional control on transport properties to optimize performance. Through computational predictions for both materials searches and design, a new paradigm in thermoelectric materials discovery is emerging.« less

Computationally guided discovery of thermoelectric materials

DOE PAGES

Gorai, Prashun; Stevanović, Vladan; Toberer, Eric S.

2017-08-22

The potential for advances in thermoelectric materials, and thus solid-state refrigeration and power generation, is immense. Progress so far has been limited by both the breadth and diversity of the chemical space and the serial nature of experimental work. In this Review, we discuss how recent computational advances are revolutionizing our ability to predict electron and phonon transport and scattering, as well as materials dopability, and we examine efficient approaches to calculating critical transport properties across large chemical spaces. When coupled with experimental feedback, these high-throughput approaches can stimulate the discovery of new classes of thermoelectric materials. Within smaller materialsmore » subsets, computations can guide the optimal chemical and structural tailoring to enhance materials performance and provide insight into the underlying transport physics. Beyond perfect materials, computations can be used for the rational design of structural and chemical modifications (such as defects, interfaces, dopants and alloys) to provide additional control on transport properties to optimize performance. Through computational predictions for both materials searches and design, a new paradigm in thermoelectric materials discovery is emerging.« less

Materials Selection for Aerospace Systems

NASA Technical Reports Server (NTRS)

Arnold, Steven M.; Cebon, David; Ashby, Mike

2012-01-01

A systematic design-oriented, five-step approach to material selection is described: 1) establishing design requirements, 2) material screening, 3) ranking, 4) researching specific candidates and 5) applying specific cultural constraints to the selection process. At the core of this approach is the definition performance indices (i.e., particular combinations of material properties that embody the performance of a given component) in conjunction with material property charts. These material selection charts, which plot one property against another, are introduced and shown to provide a powerful graphical environment wherein one can apply and analyze quantitative selection criteria, such as those captured in performance indices, and make trade-offs between conflicting objectives. Finding a material with a high value of these indices maximizes the performance of the component. Two specific examples pertaining to aerospace (engine blades and pressure vessels) are examined, both at room temperature and elevated temperature (where time-dependent effects are important) to demonstrate the methodology. The discussion then turns to engineered/hybrid materials and how these can be effectively tailored to fill in holes in the material property space, so as to enable innovation and increases in performance as compared to monolithic materials. Finally, a brief discussion is presented on managing the data needed for materials selection, including collection, analysis, deployment, and maintenance issues.

Measuring organisational-level Aboriginal cultural climate to tailor cultural safety strategies.

PubMed

Gladman, Justin; Ryder, Courtney; Walters, Lucie K

2015-01-01

Australian medical schools have taken on a social accountability mandate to provide culturally safe contexts in order to encourage Aboriginal and Torres Strait Islander people to engage in medical education and to ensure that present and future clinicians provide health services that contribute to improving the health outcomes of Aboriginal and Torres Strait Islander peoples. Many programs have sought to improve cultural safety through training at an individual level; however, it is well recognised that learners tend to internalise the patterns of behaviour to which they are commonly exposed. This project aimed to measure and reflect on the cultural climate of an Australian rural clinical school (RCS) as a whole and the collective attitudes of three different professional groups: clinicians, clinical academics and professional staff. The project then drew on Mezirow's Transformative Learning theory to design strategies to build on the cultural safety of the organisation. Clinicians, academic and professional staff at an Australian RCS were invited to participate in an online survey expressing their views on Aboriginal health using part of a previously validated tool. Survey response rate was 63%. All three groups saw Aboriginal health as a social priority. All groups recognised the fundamental role of community control in Aboriginal health; however, clinical academics were considerably more likely to disagree that the Western medical model suited the health needs of Aboriginal people. Clinicians were more likely to perceive that they treated Aboriginal patients the same as other patients. There was only weak evidence of future commitments to Aboriginal health. Importantly, clinicians, academics and professional staff demonstrated differences in their cultural safety profile which indicated the need for a tailored approach to cultural safety learning in the future. Through tailored approaches to cross-cultural training opportunities we are likely to ensure

Lithium aluminosilicate reinforced with carbon nanofiber and alumina for controlled-thermal-expansion materials

NASA Astrophysics Data System (ADS)

Borrell, Amparo; García-Moreno, Olga; Torrecillas, Ramón; García-Rocha, Victoria; Fernández, Adolfo

2012-02-01

Materials with a very low or tailored thermal expansion have many applications ranging from cookware to the aerospace industry. Among others, lithium aluminosilicates (LAS) are the most studied family with low and negative thermal expansion coefficients. However, LAS materials are electrical insulators and have poor mechanical properties. Nanocomposites using LAS as a matrix are promising in many applications where special properties are achieved by the addition of one or two more phases. The main scope of this work is to study the sinterability of carbon nanofiber (CNFs)/LAS and CNFs/alumina/LAS nanocomposites, and to adjust the ratio among components for obtaining a near-zero or tailored thermal expansion. Spark plasma sintering of nanocomposites, consisting of commercial CNFs and alumina powders and an ad hoc synthesized β-eucryptite phase, is proposed as a solution to improving mechanical and electrical properties compared with the LAS ceramics obtained under the same conditions. X-ray diffraction results on phase compositions and microstructure are discussed together with dilatometry data obtained in a wide temperature range (-150 to 450 °C). The use of a ceramic LAS phase makes it possible to design a nanocomposite with a very low or tailored thermal expansion coefficient and exceptional electrical and mechanical properties.

Method of altering the effective bulk density of solid material and the resulting product

DOEpatents

Kool, Lawrence B.; Nolen, Robert L.; Solomon, David E.

1983-01-01

A method of adjustably tailoring the effective bulk density of a solid material in which a mixture comprising the solid material, a film-forming polymer and a volatile solvent are sprayed into a drying chamber such that the solvent evaporates and the polymer dries into hollow shells having the solid material captured within the shell walls. Shell density may be varied as a function of solid/polymer concentration, droplet size and drying temperature.

Thin tailored composite wing for civil tiltrotor

NASA Technical Reports Server (NTRS)

Rais-Rohani, Masoud

1994-01-01

The tiltrotor aircraft is a flight vehicle which combines the efficient low speed (i.e., take-off, landing, and hover) characteristics of a helicopter with the efficient cruise speed of a turboprop airplane. A well-known example of such vehicle is the Bell-Boeing V-22 Osprey. The high cruise speed and range constraints placed on the civil tiltrotor require a relatively thin wing to increase the drag-divergence Mach number which translates into lower compressibility drag. It is required to reduce the wing maximum thickness-to-chord ratio t/c from 23% (i.e., V-22 wing) to 18%. While a reduction in wing thickness results in improved aerodynamic efficiency, it has an adverse effect on the wing structure and it tends to reduce structural stiffness. If ignored, the reduction in wing stiffness leads to susceptibility to aeroelastic and dynamic instabilities which may consequently cause a catastrophic failure. By taking advantage of the directional stiffness characteristics of composite materials the wing structure may be tailored to have the necessary stiffness, at a lower thickness, while keeping the weight low. The goal of this study is to design a wing structure for minimum weight subject to structural, dynamic and aeroelastic constraints. The structural constraints are in terms of strength and buckling allowables. The dynamic constraints are in terms of wing natural frequencies in vertical and horizontal bending and torsion. The aeroelastic constraints are in terms of frequency placement of the wing structure relative to those of the rotor system. The wing-rotor-pylon aeroelastic and dynamic interactions are limited in this design study by holding the cruise speed, rotor-pylon system, and wing geometric attributes fixed. To assure that the wing-rotor stability margins are maintained a more rigorous analysis based on a detailed model of the rotor system will need to ensue following the design study. The skin-stringer-rib type architecture is used for the wing

The Active plus protocol: systematic development of two theory- and evidence-based tailored physical activity interventions for the over-fifties.

PubMed

van Stralen, Maartje M; Kok, Gerjo; de Vries, Hein; Mudde, Aart N; Bolman, Catherine; Lechner, Lilian

2008-12-04

Limited data are available on the development, implementation and evaluation processes of physical activity promotion programmes among older adults. More integrative insights into interventions describing the planned systematic development, implementation and evaluation are needed. The purpose of this study is to give an integrative insight into the development of the Active plus programme applying the six-step Intervention Mapping protocol. The Active plus programme consisted of two theory- and evidence-based tailored physical activity promotion interventions, both comprising three tailored letters delivered over four months and aimed at raising awareness of insufficient physical activity, and stimulating physical activity initiation and maintenance among the over-fifties. The first intervention, the basic tailored intervention, provided tailored letters that intervened on the psychosocial determinants of physical activity. The second intervention, the intervention plus, provided the same tailored information but additionally provided tailored information about physical activity opportunities in the specific environment in which the older adults lived. This environment-based component also provided access to a forum and e-buddy system on a website. A plan for implementation and evaluation is also described. The planned development of the Active plus programme resulted in two theory- and evidence-based tailored physical activity interventions targeted at the over-fifties. Dutch Trial Register NTR 920.

Fingerprinting of Materials: Technical Supplement

NASA Technical Reports Server (NTRS)

Workman, Gary L.

1992-01-01

This supplement to the Guidelines for Maintaining a Chemical Fingerprinting Program has been developed to assist NASA personnel, contractors, and sub-contractors in defining the technical aspects and basic concepts which can be used in chemical fingerprinting programs. This material is not meant to be totally inclusive to all chemical fingerprinting programs, but merely to present current concepts. Each program will be tailored to meet the needs of the individual organizations using chemical fingerprinting to improve their quality and reliability in the production of aerospace systems.

Tailoring Selective Laser Melting Process Parameters for NiTi Implants

NASA Astrophysics Data System (ADS)

Bormann, Therese; Schumacher, Ralf; Müller, Bert; Mertmann, Matthias; de Wild, Michael

2012-12-01

Complex-shaped NiTi constructions become more and more essential for biomedical applications especially for dental or cranio-maxillofacial implants. The additive manufacturing method of selective laser melting allows realizing complex-shaped elements with predefined porosity and three-dimensional micro-architecture directly out of the design data. We demonstrate that the intentional modification of the applied energy during the SLM-process allows tailoring the transformation temperatures of NiTi entities within the entire construction. Differential scanning calorimetry, x-ray diffraction, and metallographic analysis were employed for the thermal and structural characterizations. In particular, the phase transformation temperatures, the related crystallographic phases, and the formed microstructures of SLM constructions were determined for a series of SLM-processing parameters. The SLM-NiTi exhibits pseudoelastic behavior. In this manner, the properties of NiTi implants can be tailored to build smart implants with pre-defined micro-architecture and advanced performance.

All-optical central-frequency-programmable and bandwidth-tailorable radar

PubMed Central

Zou, Weiwen; Zhang, Hao; Long, Xin; Zhang, Siteng; Cui, Yuanjun; Chen, Jianping

2016-01-01

Radar has been widely used for military, security, and rescue purposes, and modern radar should be reconfigurable at multi-bands and have programmable central frequencies and considerable bandwidth agility. Microwave photonics or photonics-assisted radio-frequency technology is a unique solution to providing such capabilities. Here, we demonstrate an all-optical central-frequency-programmable and bandwidth-tailorable radar architecture that provides a coherent system and utilizes one mode-locked laser for both signal generation and reception. Heterodyning of two individually filtered optical pulses that are pre-chirped via wavelength-to-time mapping generates a wideband linearly chirped radar signal. The working bands can be flexibly tailored with the desired bandwidth at a user-preferred carrier frequency. Radar echoes are first modulated onto the pre-chirped optical pulse, which is also used for signal generation, and then stretched in time or compressed in frequency several fold based on the time-stretch principle. Thus, digitization is facilitated without loss of detection ability. We believe that our results demonstrate an innovative radar architecture with an ultra-high-range resolution. PMID:26795596

Optimizing Decision Support for Tailored Health Behavior Change Applications.

PubMed

Kukafka, Rita; Jeong, In cheol; Finkelstein, Joseph

2015-01-01

The Tailored Lifestyle Change Decision Aid (TLC DA) system was designed to provide support for a person to make an informed choice about which behavior change to work on when multiple unhealthy behaviors are present. TLC DA can be delivered via web, smartphones and tablets. The system collects a significant amount of information that is used to generate tailored messages to consumers to persuade them in certain healthy lifestyles. One limitation is the necessity to collect vast amounts of information from users who manually enter. By identifying an optimal set of self-reported parameters we will be able to minimize the data entry burden of the app users. The study was to identify primary determinants of health behavior choices made by patients after using the system. Using discriminant analysis an optimal set of predictors was identified. The resulting set included smoking status, smoking cessation success estimate, self-efficacy, body mass index and diet status. Predicting smoking cessation choice was the most accurate, followed by weight management. Physical activity and diet choices were better identified in a combined cluster.

Aero/structural tailoring of engine blades (AERO/STAEBL)

NASA Technical Reports Server (NTRS)

Brown, K. W.

1988-01-01

This report describes the Aero/Structural Tailoring of Engine Blades (AERO/STAEBL) program, which is a computer code used to perform engine fan and compressor blade aero/structural numerical optimizations. These optimizations seek a blade design of minimum operating cost that satisfies realistic blade design constraints. This report documents the overall program (i.e., input, optimization procedures, approximate analyses) and also provides a detailed description of the validation test cases.

Structural Tailoring of Advanced Turboprops (STAT) programmer's manual

NASA Technical Reports Server (NTRS)

Brown, K. W.; Harvey, P. R.

1989-01-01

The Structural Tailoring of Advanced Turboprops (STAT) computer program was developed to perform numerical optimizations on highly swept propfan blades. This manual describes the functionality of the STAT system from a programmer's viewpoint. It provides a top-down description of module intent and interaction. The purpose of this manual is to familiarize the programmer with the STAT system should he/she wish to enhance or verify the program's function.

Tailored instructor feedback leads to more effective virtual-reality laparoscopic training.

PubMed

Paschold, M; Huber, T; Zeißig, S R; Lang, H; Kneist, Werner

2014-03-01

Laparoscopic novices begin at different performance levels, and studies on tailored training concepts are warranted. The effect of verbal instructor feedback has been investigated with varying results, and its effectiveness in virtual-reality laparoscopic (VRL) simulations still is unclear. This study aimed to determine whether laparoscopic novices with lower initial performance statuses may profit from training with intensive instructor feedback. A prospective, single-blinded study was performed within a week-long curricular course. In this study, 20 medical students performed a complex bimanual maneuver on a VRL simulator. There was a division in performance levels, with a high-performer group (HPG) that received a better median score and a low-performer group (LPG). During the training phase, only the initial LPG received standardized instructor feedback in a one-to-one setting. The final assessment of skills for both groups involved performing the task without feedback at the end of the course. The HPG and LPG showed significantly different initial performance levels according global and categorized (time, economics, error) scores (p < 0.005). This difference disappeared quickly throughout the instructor feedback phase. The final assessment demonstrated that both groups were at the same level of performance. This is the first study to use a tailored training concept with instructor feedback limited to the LPG. The tailored training was effective and economic for the laparoscopic novices and their teachers.

Feasibility and Acceptability of a Colocated Homeless-Tailored Primary Care Clinic and Emergency Department.

PubMed

Gabrielian, Sonya; Chen, Jennifer C; Minhaj, Beena P; Manchanda, Rishi; Altman, Lisa; Koosis, Ella; Gelberg, Lillian

2017-10-01

Homeless adults have low primary care engagement and high emergency department (ED) utilization. Homeless-tailored, patient-centered medical homes (PCMH) decrease this population's acute care use. We studied the feasibility (focused on patient recruitment) and acceptability (conceptualized as clinicians' attitudes/beliefs) of a pilot initiative to colocate a homeless-tailored PCMH with an ED. After ED triage, low-acuity patients appropriate for outpatient care were screened for homelessness; homeless patients chose between a colocated PCMH or ED visit. To study feasibility, we captured (from May to September 2012) the number of patients screened for homelessness, positive screens, unique patients seen, and primary care visits. We focused on acceptability to ED clinicians (physicians, nurses, social workers); we sent a 32-item survey to ED clinicians (n = 57) who worked during clinic hours. Questions derived from an instrument measuring clinician attitudes toward homeless persons; acceptability of homelessness screening and the clinic itself were also explored. Over the 5 months of interest, 281 patients were screened; 172 (61.2%) screened positive for homelessness; 112 (65.1%) of these positive screens were seen over 215 visits. Acceptability data were obtained from 56% (n = 32) of surveyed clinicians. Attitudes toward homeless patients were similar to prior studies of primary care physicians. Most (54.6%) clinicians agreed with the homelessness screening procedures. Nearly all (90.3%) clinicians supported expansion of the homeless-tailored clinic; a minority (42.0%) agreed that ED colocation worked well. Our data suggest the feasibility of recruiting patients to a homeless-tailored primary care clinic colocated with the ED; however, the clinic's acceptability was mixed. Future quality improvement work should focus on tailoring the clinic to increase its acceptability among ED clinicians, while assessing its impact on health, housing, and costs.

Feasibility and Acceptability of a Colocated Homeless-Tailored Primary Care Clinic and Emergency Department

PubMed Central

Gabrielian, Sonya; Chen, Jennifer C.; Minhaj, Beena P.; Manchanda, Rishi; Altman, Lisa; Koosis, Ella; Gelberg, Lillian

2017-01-01

Objectives: Homeless adults have low primary care engagement and high emergency department (ED) utilization. Homeless-tailored, patient-centered medical homes (PCMH) decrease this population’s acute care use. We studied the feasibility (focused on patient recruitment) and acceptability (conceptualized as clinicians’ attitudes/beliefs) of a pilot initiative to colocate a homeless-tailored PCMH with an ED. After ED triage, low-acuity patients appropriate for outpatient care were screened for homelessness; homeless patients chose between a colocated PCMH or ED visit. Methods: To study feasibility, we captured (from May to September 2012) the number of patients screened for homelessness, positive screens, unique patients seen, and primary care visits. We focused on acceptability to ED clinicians (physicians, nurses, social workers); we sent a 32-item survey to ED clinicians (n = 57) who worked during clinic hours. Questions derived from an instrument measuring clinician attitudes toward homeless persons; acceptability of homelessness screening and the clinic itself were also explored. Results: Over the 5 months of interest, 281 patients were screened; 172 (61.2%) screened positive for homelessness; 112 (65.1%) of these positive screens were seen over 215 visits. Acceptability data were obtained from 56% (n = 32) of surveyed clinicians. Attitudes toward homeless patients were similar to prior studies of primary care physicians. Most (54.6%) clinicians agreed with the homelessness screening procedures. Nearly all (90.3%) clinicians supported expansion of the homeless-tailored clinic; a minority (42.0%) agreed that ED colocation worked well. Conclusion: Our data suggest the feasibility of recruiting patients to a homeless-tailored primary care clinic colocated with the ED; however, the clinic’s acceptability was mixed. Future quality improvement work should focus on tailoring the clinic to increase its acceptability among ED clinicians, while assessing its impact on

TAILORING A FRUIT AND VEGETABLE INTERVENTION ON ETHNIC IDENTITY: RESULTS OF A RANDOMIZED STUDY

PubMed Central

Resnicow, Ken; Davis, Rachel; Zhang, Nanhua; Saunders, Ed; Strecher, Victor; Tolsma, Dennis; Calvi, Josephine; Alexander, Gwen; Anderson, Julia; Wiese, Cheryl; Cross, William

2009-01-01

Objective Many targeted health interventions have been developed and tested with African American (AA) populations; however, AAs are a highly heterogeneous group. One characteristic that varies across AAs is Ethnic Identity (EI). Despite the recognition that AAs are heterogeneous with regard to EI, little research has been conducted on how to incorporate EI into the design of health messages and programs. Design This randomized trial tested whether tailoring a print-based fruit and vegetable (F & V) intervention based on individual EI would enhance program impact beyond that of social cognitive tailoring alone. AA adults were recruited from two integrated healthcare delivery systems, one based in the Detroit Metro area and the other in the Atlanta Metro area, and then randomized to receive three newsletters focused on F & V behavior change over three months. One set of newsletters was tailored only on demographic, behavioral, and social cognitive variables (control condition) whereas the other (experimental condition) was additionally tailored on EI. Main Outcome Measures The primary outcome for the study was F & V intake, which was assessed at baseline and three months later using the composite of two brief self-report frequency measures. Results A total of 560 eligible participants were enrolled, of which 468 provided complete 3-month follow-up data. The experimental group increased their daily mean F & V intake by 1.1 servings compared to .8 servings in the control group (p = .13). Several variables were found to interact with intervention group. For instance, Afrocentric experimental group participants showed a 1.4 increase in F & V servings per day compared to a .43 servings per day increase among Afrocentric controls (p < .05). Conclusions Although the overall between-group effects were not significant, this study confirms that AAs are a highly diverse population and that tailoring dietary messages on ethnic identity may improve intervention impact for some

Harnessing the synthetic capabilities of glycopeptide antibiotic tailoring enzymes: characterization of the UK-68,597 biosynthetic cluster.

PubMed

Yim, Grace; Kalan, Lindsay; Koteva, Kalinka; Thaker, Maulik N; Waglechner, Nicholas; Tang, Irene; Wright, Gerard D

2014-11-24

In this study, a draft genome sequence of Actinoplanes sp. ATCC 53533 was assembled, and an 81-kb biosynthetic cluster for the unusual sulfated glycopeptide UK-68,597 was identified. Glycopeptide antibiotics are important in the treatment of infections caused by Gram-positive bacteria. Glycopeptides contain heptapeptide backbones that are modified by many tailoring enzymes, including glycosyltransferases, sulfotransferases, methyltransferases, and halogenases, generating extensive chemical and functional diversity. Several tailoring enzymes in the cluster were examined in vitro for their ability to modify glycopeptides, resulting in the synthesis of novel molecules. Tailoring enzymes were also expressed in the producer of the glycopeptide aglycone A47934, generating additional chemical diversity. This work characterizes the biosynthetic program of UK-68,597 and demonstrates the capacity to expand glycopeptide chemical diversity by harnessing the unique chemistry of tailoring enzymes. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Does stage tailoring matter in brief alcohol interventions for job-seekers? A randomized controlled trial.

PubMed

Freyer-Adam, Jennis; Baumann, Sophie; Schnuerer, Inga; Haberecht, Katja; Bischof, Gallus; John, Ulrich; Gaertner, Beate

2014-11-01

To investigate whether or not a stage tailored intervention is more effective than a non-stage tailored intervention of the same intensity in reducing alcohol use among job-seekers with unhealthy alcohol use, and whether initial motivation to change is a moderator of efficacy. A three-group randomized controlled trial with 3-, 6- and 15-month follow-ups. Three job agencies in Germany. A total of 1243 job-seekers with unhealthy alcohol use were randomized to (i) stage tailored intervention based on the transtheoretical model of change (ST), (ii) non-stage tailored intervention based on the theory of planned behaviour (NST) and (iii) assessment only (controls). Participants received feedback letters and manuals at baseline and 3 months later. Piecewise latent growth models were calculated measuring change in 'alcohol use' from baseline to month 3 (active intervention phase) and from months 3 to 15 (post-intervention phase, primary outcome). Motivation to change was included as a 4-point continuous measure. All groups reduced alcohol use from months 0 to 3 (controls: mean = -0.866, NST: mean = -0.883, ST: mean = -0.718, Ps ≤ 0.001). Post-intervention (months 3-15), low-motivated individuals in the ST group showed a greater reduction than those in the control group (β = 0.135, P = 0.039, Cohen's d = 0.42) and in the NST group (β = 0.180, P = 0.009, Cohen's d = 0.55). In contrast, compared to the ST group (β = 0.030, P = 0.361), alcohol use decreased more strongly with higher initial motivation in the NST group (β = -0.118, P = 0.010). Among job-seekers with high levels of alcohol consumption, an intervention tailored to motivational 'stage of change' was more effective than a non-stage tailored intervention for reducing alcohol use 15 months after baseline assessment in participants with low initial motivation to change. © 2014 Society for the Study of Addiction.

Development of patient-centric linguistically tailored psychoeducational messages to support nutrition and medication self-management in type 2 diabetes: a feasibility study

PubMed Central

Ellis, Rebecca J Bartlett; Connor, Ulla; Marshall, James

2014-01-01

Purpose This study evaluated the feasibility of developing linguistically tailored educational messages designed to match the linguistic styles of patients segmented into types with the Descriptor™, and to determine patient preferences for tailored or standard messages based on their segments. Patients and methods Twenty patients with type 2 diabetes (T2DM) were recruited from a diabetes health clinic. Participants were segmented using the Descriptor™, a language-based questionnaire, to identify patient types based on their control orientation (internal/external), agency (high/low), and affect (positive/negative), which are well studied constructs related to T2DM self-management. Two of the seven self-care behaviors described by the American Association of Diabetes Educators (healthy eating and taking medication) were used to develop standard messages and then linguistically tailored using features of the six different construct segment types of the Descriptor™. A subset of seven participants each provided feedback on their preference for standard or linguistically tailored messages; 12 comparisons between standard and tailored messages were made. Results Overall, the tailored messages were preferred to the standard messages. When the messages were matched to specific construct segment types, the tailored messages were preferred over the standard messages, although this was not statistically significant. Conclusion Linguistically tailoring messages based on construct segments is feasible. Furthermore, tailored messages were more often preferred over standard messages. This study provides some preliminary evidence for tailoring messages based on the linguistic features of control orientation, agency, and affect. The messages developed in this study should be tested in a larger more representative sample. The present study did not explore whether tailored messages were better understood. This research will serve as preliminary evidence to develop future studies

Mechanism of adaptability for the nano-structured TiAlCrSiYN-based hard physical vapor deposition coatings under extreme frictional conditions

NASA Astrophysics Data System (ADS)

Fox-Rabinovich, G. S.; Endrino, J. L.; Aguirre, M. H.; Beake, B. D.; Veldhuis, S. C.; Kovalev, A. I.; Gershman, I. S.; Yamamoto, K.; Losset, Y.; Wainstein, D. L.; Rashkovskiy, A.

2012-03-01

Recently, a family of hard mono- and multilayer TiAlCrSiYN-based coatings have been introduced that exhibit adaptive behavior under extreme tribological conditions (in particular during dry ultrahigh speed machining of hardened tool steels). The major feature of these coatings is the formation of the tribo-films on the friction surface which possess high protective ability under operating temperatures of 1000 °C and above. These tribo-films are generated as a result of a self-organization process during friction. But the mechanism how these films affect adaptability of the hard coating is still an open question. The major mechanism proposed in this paper is associated with a strong gradient of temperatures within the layer of nano-scaled tribo-films. This trend was outlined by the performed thermodynamic analysis of friction phenomena combined with the developing of a numerical model of heat transfer within cutting zone based on the finite element method. The results of the theoretical studies show that the major physical-chemical processes during cutting are mostly concentrated within a layer of the tribo-films. This nano-tribological phenomenon produces beneficial heat distribution at the chip/tool interface which controls the tool life and wear behavior.Results of x-ray photoelectron spectroscopy studies indicate enhanced formation of protective sapphire- and mullite-like tribo-films on the friction surface of the multilayer TiAlCrSiYN/TiAlCrN coating. Comprehensive investigations of the structure and phase transformation within the coating layer under operation have been performed, using high resolution transmission electron microscopy, synchrotron radiation technique: x-ray absorption near-edge structure and XRD methods.The data obtained show that the tribo-films efficiently perform their thermal barrier functions preventing heat to penetrate into the body of coated cutting tool. Due to this the surface damaging process as well as non-beneficial phase

Comprehensive overview of computer-based health information tailoring: a scoping review protocol.

PubMed

Ghalibaf, Azadeh Kamel; Nazari, Elham; Gholian-Aval, Mahdi; Tabesh, Hamed; Tara, Mahmood

2017-12-27

Tailoring health information to the needs of individuals has become an important part of modern health communications. Tailoring has been addressed by researchers from different disciplines leading to the emergence of a wide range of approaches, making the newcomers confused. In order to address this, a comprehensive overview of the field with the indications of research gaps, tendencies and trends will be helpful. As a result, a systematic protocol was outlined to conduct a scoping review within the field of computer-based health information tailoring. This protocol is based on the York's five-stage framework outlined by Arksey and O'Malley. A field-specific structure was defined as a basis for undertaking each stage. The structure comprised three main aspects: system design , information communication and evaluation . Five leading databases were searched: PubMed, Scopus, Science Direct, EBSCO and IEEE and a broad search strategy was used with less strict inclusion criteria to cover the breadth of evidence. Theoretical frameworks were used to develop the data extraction form and a rigorous approach was introduced to identify the categories from data. Several explanatory-descriptive methods were considered to analyse the data, from which some were proposed to be employed for the first time in scoping studies. This study investigates the breadth and depth of existing literature on computer-tailoring and as a secondary analysis, does not require ethics approval. We anticipate that the results will identify research gaps and novel ideas for future studies and provide direction to combine methods from different disciplines. The research findings will be submitted for publication to relevant peer-reviewed journals and conferences targeting health promotion and patient education. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Active coatings technologies for tailorable military coating systems

NASA Astrophysics Data System (ADS)

Zunino, J. L., III

2007-04-01

The main objective of the U.S. Army's Active Coatings Technologies Program is to develop technologies that can be used in combination to tailor coatings for utilization on Army Materiel. The Active Coatings Technologies Program, ACT, is divided into several thrusts, including the Smart Coatings Materiel Program, Munitions Coatings Technologies, Active Sensor packages, Systems Health Monitoring, Novel Technology Development, as well as other advanced technologies. The goal of the ACT Program is to conduct research leading to the development of multiple coatings systems for use on various military platforms, incorporating unique properties such as self repair, selective removal, corrosion resistance, sensing, ability to modify coatings' physical properties, colorizing, and alerting logistics staff when tanks or weaponry require more extensive repair. A partnership between the U.S. Army Corrosion Office at Picatinny Arsenal, NJ along with researchers at the New Jersey Institute of Technology, NJ, Clemson University, SC, University of New Hampshire, NH, and University of Massachusetts (Lowell), MA, are developing the next generation of Smart Coatings Materiel via novel technologies such as nanotechnology, Micro-electromechanical Systems (MEMS), meta-materials, flexible electronics, electrochromics, electroluminescence, etc. This paper will provide the reader with an overview of the Active Coatings Technologies Program, including an update of the on-going Smart Coatings Materiel Program, its progress thus far, description of the prototype Smart Coatings Systems and research tasks as well as future nanotechnology concepts, and applications for the Department of Defense.

User-centered Design of the eyeGuide: A Tailored Glaucoma Behavior Change Program.

PubMed

Killeen, Olivia J; MacKenzie, Chamisa; Heisler, Michele; Resnicow, Ken; Lee, Paul P; Newman-Casey, Paula Anne

2016-10-01

We employed user-centered design to refine a prototype of the eyeGuide, a novel, tailored behavior change program intended to improve medication adherence among glaucoma patients. Glaucoma patients age 40 years and above prescribed ≥1 glaucoma medication were included. The eyeGuide consists of tailored educational content and tailored testimonials in which patients share how they were able to overcome barriers to improve their medication adherence. A hybrid of semistructured diagnostic and pretesting interviews were used to refine the content of the eyeGuide. Purposeful sampling was used to recruit a study population representative of the glaucoma patient population. Interviews were conducted until thematic saturation was reached. Interviews were audiorecorded and transcribed verbatim. Three researchers analyzed the transcripts, generated a codebook, and identified key themes using NVivo 10.0 to further refine the eyeGuide. Twenty-one glaucoma patients were interviewed; mean age 72±12.4 years, 5 (24%) African Americans, 9 (43%) with poor self-reported adherence, 10 (47.6%) age 75 years and above, 10 (47.6%) with poor vision, and 9 (42.9%) women. Qualitative analysis identified 5 important themes for improving glaucoma self-management: social support, patient-provider relationship, medication routine, patients' beliefs about disease and treatment, and eye drop instillation. All participants expressed satisfaction with in-person delivery of the eyeGuide and preferred this to a Web-based module. Participant feedback resulted in revised content. User-centered design generated improvements in the eyeGuide that would not have been possible without patient input. Participants expressed satisfaction with the tailored content.

Materials characterization with MeV ions

NASA Astrophysics Data System (ADS)

Conlon, T. W.

1989-04-01

The inherent atomic and nuclear properties of energetic ions in materials can be exploited to characterize as well as to modify materials' properties. In nuclear reactors keV ions from neutron collisions damage containment materials. However, basic studies of the interactions of such ions has yielded improved understanding of their properties and has even led to a tailoring of conditions so that the ions can be made to beneficially modify structures (by ion implantation). At higher energies an understanding of the ion-material interaction provides techniques such as PIXE, RBS, and ERD for nondestructive analysis, either in broad beam or "microbeam" mode. At high energies still penetration of the Coulomb barrier opens up activation methods for materials' characterization (CPAA, NRA, TLA etc.). A short discussion of the general properties of energetic ions in materials is followed by a brief introduction to our generic work in these areas, and some examples of current work in the areas of: activation for the radioisotope labelling of nonmetals, mass resolved ERDA using TOF techniques and submicron MeV microprobes.

Field emission device driven by self-powered contact-electrification: Simulation and experimental analysis

NASA Astrophysics Data System (ADS)

Chen, Xiangyu; Jiang, Tao; Sun, Zhuo; Ou-Yang, Wei

2015-09-01

A self-powered field emission device (FED) driven by a single-electrode tribo-electric nanogenerator (TENG) is demonstrated. The mechanical motion works as both a power supply to drive the FED and a control unit to regulate the amount of emitted electrons. By using the Fowler-Nordheim equation and Kirchhoff laws, a theoretical model of this self-powered FED is proposed, and accordingly the real-time output characteristics of the device are systematically investigated. It is found that the motion distance of the TENG controls switch-on of the FED and determines the charge amount for emission, while the motion velocity regulates the amplitude of emission current. The minimum contact area for the TENG to generate field emission is about 9 cm2, which can be improved by optimizing FED structure and the tribo-materials of TENG. The demonstrated concept of this self-powered FED as well as the proposed physical analysis can serve as guidance for further applications of FED in such fields of self-powered electronics and soft electronics.

Field emission device driven by self-powered contact-electrification: Simulation and experimental analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Xiangyu, E-mail: chenxiangyu@binn.cas.cn, E-mail: ouyangwei@phy.ecnu.edu.cn; Jiang, Tao; Sun, Zhuo

A self-powered field emission device (FED) driven by a single-electrode tribo-electric nanogenerator (TENG) is demonstrated. The mechanical motion works as both a power supply to drive the FED and a control unit to regulate the amount of emitted electrons. By using the Fowler-Nordheim equation and Kirchhoff laws, a theoretical model of this self-powered FED is proposed, and accordingly the real-time output characteristics of the device are systematically investigated. It is found that the motion distance of the TENG controls switch-on of the FED and determines the charge amount for emission, while the motion velocity regulates the amplitude of emission current.more » The minimum contact area for the TENG to generate field emission is about 9 cm{sup 2}, which can be improved by optimizing FED structure and the tribo-materials of TENG. The demonstrated concept of this self-powered FED as well as the proposed physical analysis can serve as guidance for further applications of FED in such fields of self-powered electronics and soft electronics.« less

A Randomized Controlled Trial of a Tailored Interactive Computer-Delivered Intervention to Promote Colorectal Cancer Screening: Sometimes More is Just the Same

PubMed Central

Bartholomew, Leona K.; McQueen, Amy; Bettencourt, Judy L.; Greisinger, Anthony; Coan, Sharon P.; Lairson, David; Chan, Wenyaw; Hawley, S. T.; Myers, R. E.

2012-01-01

Background There have been few studies of tailored interventions to promote colorectal cancer (CRC) screening. Purpose We conducted a randomized trial of a tailored, interactive intervention to increase CRC screening. Methods Patients 50–70 years completed a baseline survey, were randomized to one of three groups, and attended a wellness exam after being exposed to a tailored intervention about CRC screening (tailored group), a public web site about CRC screening (web site group), or no intervention (survey-only group). The primary outcome was completion of any recommended CRC screening by 6 months. Results There was no statistically significant difference in screening by 6 months: 30%, 31%, and 28% of the survey-only, web site, and tailored groups were screened. Exposure to the tailored intervention was associated with increased knowledge and CRC screening self-efficacy at 2 weeks and 6 months. Family history, prior screening, stage of change, and physician recommendation moderated the intervention effects. Conclusions A tailored intervention was not more effective at increasing screening than a public web site or only being surveyed. PMID:21271365

Optimizing Online Suicide Prevention: A Search Engine-Based Tailored Approach.

PubMed

Arendt, Florian; Scherr, Sebastian

2017-11-01

Search engines are increasingly used to seek suicide-related information online, which can serve both harmful and helpful purposes. Google acknowledges this fact and presents a suicide-prevention result for particular search terms. Unfortunately, the result is only presented to a limited number of visitors. Hence, Google is missing the opportunity to provide help to vulnerable people. We propose a two-step approach to a tailored optimization: First, research will identify the risk factors. Second, search engines will reweight algorithms according to the risk factors. In this study, we show that the query share of the search term "poisoning" on Google shows substantial peaks corresponding to peaks in actual suicidal behavior. Accordingly, thresholds for showing the suicide-prevention result should be set to the lowest levels during the spring, on Sundays and Mondays, on New Year's Day, and on Saturdays following Thanksgiving. Search engines can help to save lives globally by utilizing a more tailored approach to suicide prevention.

Tailoring partially reduced graphene oxide as redox mediator for enhanced biotransformation of iopromide under methanogenic and sulfate-reducing conditions.

PubMed

Toral-Sánchez, Eduardo; Rangel-Mendez, J Rene; Ascacio Valdés, Juan A; Aguilar, Cristóbal N; Cervantes, Francisco J

2017-01-01

This work reports the first successful application of graphene oxide (GO) and partially reduced GO (rGO) as redox mediator (RM) to increase the biotransformation of the recalcitrant iodinated contrast medium, iopromide (IOP). Results showed that GO-based materials promoted up to 5.5 and 2.8-fold faster biotransformation of IOP by anaerobic sludge under methanogenic and sulfate-reducing conditions, respectively. Correlation between the extent of reduction of GO and its redox-mediating capacity was demonstrated, which was reflected in faster removal and greater extent of biotransformation of IOP. Further analysis indicated that the biotransformation pathway of IOP involved multiple reactions including deiodination, decarboxylation, demethylation, dehydration and N-dealkylation. GO-based materials could be strategically tailored and integrated in biological treatment systems to effectively enhance the redox conversion of recalcitrant pollutants commonly found in wastewater treatment systems and industrial effluents. Copyright © 2016 Elsevier Ltd. All rights reserved.

Novel 3D-printing technique for caps to enable tailored therapeutic endoscopy.

PubMed

Ko, Weon Jin; Song, Ga Won; Hong, Sung Pyo; Kwon, Chang-il; Hahm, Ki Baik; Cho, Joo Young

2016-03-01

To evaluate the feasibility of a tailored endoscopic cap created using 3D-printing technology that is customized according to esophagogastric lesions of each patient. Tailored endoscopic caps, which were designed and fabricated with a 3D printer, were inserted in 35 patients. The types of cap were side-hole cap made for cap-assisted endoscopic mucosal resection (EMRC), oblique-head cap designed for endoscopic submucosal dissection (ESD), wide-head cap used for Trucut biopsy (TCB), and narrow-tip cap to facilitate peroral endoscopic myotomy (POEM). EMRC in the esophagus and gastroesophageal junction was carried out using a side-hole cap in seven patients. Median total procedure time for successful removal of lesions was 14 min (range 8-50 min). Gastric ESD was carried out using with an oblique-head cap in 16 patients, for which the median total procedure time was 53 min. TCB in the esophagus was done using a wide-head cap in eight patients. While carrying out POEM for tunneling, a narrow-tip cap was used in four patients with achalasia. Based on the current proof-of-concept study, we anticipate that creating a tailored endoscopic cap is feasible for therapeutic endoscopy. © 2015 Japan Gastroenterological Endoscopy Society.

Increasing Physical Activity in Patients with Arthritis: A Tailored Health Promotion Program

PubMed Central

Ehrlich-Jones, Linda; Mallinson, Trudy; Fischer, Heidi; Bateman, Jillian; Semanik, Pamela A.; Spring, Bonnie; Ruderman, Eric; Chang, Rowland W.

2010-01-01

Objective Despite recent studies showing the benefit of physical activity for people with arthritis, the vast majority of persons with arthritis are not sufficiently physically active. The purpose of this report is to describe a tailored health promotion intervention aimed at increasing physical activity among persons with arthritis. The intervention is designed to be useful for health systems and insurers interested in a chronic disease management program that could be disseminated to large populations of arthritis patients. Methods The intervention is carried out by a clinician who is designated as the client’s physical activity advocate. The approach emphasizes motivational interviewing, individualized goal setting, tailored strategies for increasing physical activity and for monitoring progress, and a plan of 2 years of follow-up. The intervention includes a standardized assessment of barriers to and strengths supporting increased lifestyle physical activity. A randomized, controlled trial is underway to evaluate the efficacy and cost-effectiveness of this intervention. Conclusion This intervention is unique in that it implements a program tailored to the individual that focuses on lifestyle physical activity and long-term monitoring. The approach recognizes that persons with arthritis present with varying levels of motivation for change in physical activity and that behavior change can take a long time to become habitual. PMID:20696695

Importance of material and friction characterisation for FE-aided process design of hybrid bevel gears

NASA Astrophysics Data System (ADS)

Behrens, B.-A.; Bouguecha, A.; Bonk, C.; Matthias, T.

2017-10-01

Solid-forming components are often used in areas where they are subjected to very high loads. For most solid components locally divergent and sometimes contradictory requirements exist. Despite these contradictory requirements, almost exclusively monomaterials are nowadays used for the production of solid components. These components often reach their material-specific limits because of increasing demands on the products. Thus a significant increase in product quality and profitability would result from combining different materials in order to create tailored properties. In the Collaborative Research Center (CRC) 1153 "Tailored Forming" at the Leibniz Universität Hannover, this topic is investigated. The primary objective of the CRC 1153 is to develop and investigate new tailored manufacturing processes to produce reliable hybrid solid semi-finished components. In contrast to existing production processes of hybrid solid components, semi-finished workpieces in the CRC 1153 are joined before the forming phase. Thus, it will be possible to produce complex and highly stressable solid components made of different metals, which cannot be produced yet with the current used technologies. In this work the material and friction characteristics are investigated and the forming tool for the production of hybrid bevel gears made of different steel alloys (C22 and 41Cr4) is designed by numerical simulations. For this purpose, flow curves of both materials are determined by means of upsetting tests at process-related forming temperatures and strain rates. The temperature range for the forming process of the semi-finished product is determined by comparing the respective flow curves regarding similar flow stresses. Furthermore, the friction between the tool and the joining materials is investigated by means of ring upsetting tests at a process-relevant temperature. Finally, a stress analysis of the forming tools is carried out.

Tailoring the thermostability and hydrogen storage capacity of Li decorated carbon materials by heteroatom doping

NASA Astrophysics Data System (ADS)

Long, Jun; Li, Jieyuan; Nan, Fang; Yin, Shi; Li, Jianjun; Cen, Wanglai

2018-03-01

Li decorated graphene is supposed to be a promising material for the hydrogen storage, which can be further improved by heteroatom doping. But a unified promoting mechanism for various doping types and species are still lacking, which hinders the rational design of advanced materials. The potential of N/B doped Li decorated graphene for hydrogen storage is investigated with DFT calculations. A covalent interaction between Li and the graphene substrates is identified to control the thermostability and hydrogen storage capacity (HSC) of the Li decorated substrate, which is in turn subject to the electronegativity of doping species and the doping types. Additionally, a conceptual descriptor is proposed to predict the HSC of Li decorated graphene. These results provide a unified explanation and prediction of the effects of heteroatom doping on Li decorated carbon materials for hydrogen storage.

PVC removal from mixed plastics by triboelectrostatic separation.

PubMed

Park, Chul-Hyun; Jeon, Ho-Seok; Park, Jai-Koo

2007-06-01

Ever increasing oil price and the constant growth in generation of waste plastics stimulate a research on material separation for recycling of waste plastics. At present, most waste plastics cause serious environmental problems due to the disposal by reclamation and incineration. Particularly, polyvinyl chloride (PVC) materials among waste plastics generates hazardous HCl gas, dioxins containing Cl, and so on, which lead to air pollution and shorten the life of incinerator, and it makes difficultly recycling of other plastics. Therefore, we designed a bench scale triboelectrostatic separator for PVC removal from mixed plastics (polyvinyl chloride/polyethylene terephthalate), and then carried out material separation tests. In triboelectrostatic separation, PVC and PET particles are charged negatively and positively, respectively, due to the difference of the work function of plastics in tribo charger of the fluidized-bed, and are separated by means of splitter through an opposite electric field. In this study, the charge efficiency of PVC and PET was strongly dependent on the tribo charger material (polypropylene), relative humidity (below 30%), air velocity (over 10 m/s), and mixture ratio (PET:PVC=1:1). At the optimum conditions (electrode potential of 20 kV and splitter position of -2 cm), PVC rejection and PET recovery in PET products were 99.60 and 98.10%, respectively, and the reproducibility of optimal test was very good (+/-1%). In addition, as a change of splitter position, we developed the technique to recover high purity PET (over 99.99%) although PET recovery decreases by degrees.

HiMAT structural development design methodology. [aeroelastic tailoring of the canard and wing box and distributed load tests

NASA Technical Reports Server (NTRS)

Price, M. A.

1979-01-01

In order to improve aerodynamic performance, a twist criterion was used to design the canard and wing lifting surfaces of two graphite-epoxy research aircraft. To meet that twist criterion, the lifting surfaces were tailored using graphite-epoxy tape. The outer surface of the aircraft is essentially constructed of 95 percent graphite epoxy materials. The analytical tools and methodology used to design those lifting surfaces are described. One aircraft was subjected to an 8g ground test in order to verify structural integrity and to determine how well the desired twist was achieved. Test results are presented and the reductions of both flight and ground strain test gages and their associated stresses are discussed.

Nanostructural Tailoring to Induce Flexibility in Thermoelectric Ca3Co4O9 Thin Films

PubMed Central

2017-01-01

Because of their inherent rigidity and brittleness, inorganic materials have seen limited use in flexible thermoelectric applications. On the other hand, for high output power density and stability, the use of inorganic materials is required. Here, we demonstrate a concept of fully inorganic flexible thermoelectric thin films with Ca3Co4O9-on-mica. Ca3Co4O9 is promising not only because of its high Seebeck coefficient and good electrical conductivity but also because of the abundance, low cost, and nontoxicity of its constituent raw materials. We show a promising nanostructural tailoring approach to induce flexibility in inorganic thin-film materials, achieving flexibility in nanostructured Ca3Co4O9 thin films. The films were grown by thermally induced phase transformation from CaO–CoO thin films deposited by reactive rf-magnetron cosputtering from metallic targets of Ca and Co to the final phase of Ca3Co4O9 on a mica substrate. The pattern of nanostructural evolution during the solid-state phase transformation is determined by the surface energy and strain energy contributions, whereas different distributions of CaO and CoO phases in the as-deposited films promote different nanostructuring during the phase transformation. Another interesting fact is that the Ca3Co4O9 film is transferable onto an arbitrary flexible platform from the parent mica substrate by etch-free dry transfer. The highest thermoelectric power factor obtained is above 1 × 10–4 W m–1 K–2 in a wide temperature range, thus showing low-temperature applicability of this class of materials. PMID:28699345

Computer-Tailored Intervention for Juvenile Offenders

PubMed Central

LEVESQUE, DEBORAH A.; JOHNSON, JANET L.; WELCH, CAROL A.; PROCHASKA, JANICE M.; FERNANDEZ, ANNE C.

2012-01-01

Studies assessing the efficacy of juvenile justice interventions show small effects on recidivism and other outcomes. This paper describes the development of a prototype of a multimedia computer-tailored intervention (“Rise Above Your Situation”or RAYS) that relies on an evidence-based model of behavior change, the Transtheoretical Model, and expert system technology to deliver assessments, feedback, printed reports, and counselor reports with intervention ideas. In a feasibility test involving 60 system-involved youths and their counselors, evaluations of the program were favorable: 91.7% of youths agreed that the program could help them make positive changes, and 86.7% agreed that the program could give their counselor helpful information about them. PMID:23264754

Geometric Modeling of Cellular Materials for Additive Manufacturing in Biomedical Field: A Review.

PubMed

Savio, Gianpaolo; Rosso, Stefano; Meneghello, Roberto; Concheri, Gianmaria

2018-01-01

Advances in additive manufacturing technologies facilitate the fabrication of cellular materials that have tailored functional characteristics. The application of solid freeform fabrication techniques is especially exploited in designing scaffolds for tissue engineering. In this review, firstly, a classification of cellular materials from a geometric point of view is proposed; then, the main approaches on geometric modeling of cellular materials are discussed. Finally, an investigation on porous scaffolds fabricated by additive manufacturing technologies is pointed out. Perspectives in geometric modeling of scaffolds for tissue engineering are also proposed.

A Review of Culturally Targeted/Tailored Tobacco Prevention and Cessation Interventions for Minority Adolescents

PubMed Central

Singh, Nisha; Krishnan-Sarin, Suchitra

2012-01-01

Aim: Emerging racial/ethnic disparities in tobacco use behaviors and resulting long-term health outcomes highlight the importance of developing culturally tailored/targeted tobacco prevention and cessation interventions. This manuscript describes the efficacy and the components of prevention and cessation interventions developed for minority adolescents. Methods: Thirteen studies focused on culturally tailoring and targeting tobacco prevention/cessation interventions were selected and information on intervention design (type, number of sessions), setting (school or community), theoretical constructs, culture-specific components (surface/deep structures), and treatment outcomes were extracted. Results: Of the 13 studies, 5 focused on prevention, 4 on cessation, and 4 combined prevention and cessation, and most of the studies were primarily school-based, while a few used community locations. Although diverse minority groups were targeted, a majority of the studies (n = 6) worked with Hispanic adolescents. The most common theoretical construct examined was the Social Influence Model (n = 5). The overall findings indicated that culturally tailoring cessation interventions did not appear to improve tobacco quit rates among minority adolescents, but culturally tailored prevention interventions appeared to produce lower tobacco initiation rates among minority adolescents than control conditions. Conclusions: The results of review suggest that there is a critical need to develop better interventions to reduce tobacco use among minority adolescents and that developing a better understanding of cultural issues related to both cessation and initiation of tobacco use among minority populations is a key component of this endeavor. PMID:22614548

Ligand-tailored single-site silica supported titanium catalysts: Synthesis, characterization and towards cyanosilylation reaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Wei; Li, Yani; Yu, Bo

2015-01-15

A successive anchoring of Ti(NMe{sub 2}){sub 4}, cyclopentadiene and a O-donor ligand, 1-hydroxyethylbenzene (PEA), 1,1′-bi-2-naphthol (Binol) or 2,3-dihydroxybutanedioic acid diethyl ester (Tartrate), on silica was conducted by SOMC strategy in moderate conditions. The silica, monitored by in-situ Fourier transform infrared spectroscopy (in-situ FT-IR), was pretreated at different temperatures (200, 500 and 800 °C). The ligand tailored silica-supported titanium complexes were characterized by in-situ FT-IR, {sup 13}C CP MAS-NMR, X-ray photoelectron spectroscopy (XPS), X-ray absorption near edge structure (XANES) and elemental analysis in detail, verifying that the surface titanium species are single sited. The catalytic activity of the ligand tailored single-sitemore » silica supported titanium complexes was evaluated by a cyanosilylation of benzaldehyde. The results showed that the catalytic activity is dependent strongly on the dehydroxylation temperatures of silica and the configuration of the ligands. - Graphical abstract: The ligand-tailored silica supported “single site” titanium complexes were synthesized by SOMC strategy and fully characterized. Their catalytic activity were evaluated by benzaldehyde silylcyanation. - Highlights: • Single-site silica supported Ti active species was prepared by SOMC technique. • O-donor ligand tailored Ti surface species was synthesized. • The surface species was characterized by XPS, {sup 13}C CP-MAS NMR, XANES etc. • Catalytic activity of the Ti active species in silylcyanation reaction was evaluated.« less

Tailoring barrier properties of thermoplastic corn starch-based films (TPCS) by means of a multilayer design.

PubMed

Fabra, María José; López-Rubio, Amparo; Cabedo, Luis; Lagaron, Jose M

2016-12-01

This work compares the effect of adding different biopolyester electrospun coatings made of polycaprolactone (PCL), polylactic acid (PLA) and polyhydroxybutyrate (PHB) on oxygen and water vapour barrier properties of a thermoplastic corn starch (TPCS) film. The morphology of the developed multilayer structures was also examined by Scanning Electron Microscopy (SEM). Results showed a positive linear relationship between the amount of the electrospun coatings deposited onto both sides of the TPCS film and the thickness of the coating. Interestingly, the addition of electrospun biopolyester coatings led to an exponential oxygen and water vapour permeability drop as the amount of the electrospun coating increased. This study demonstrated the versatility of the technology here proposed to tailor the barrier properties of food packaging materials according to the final intended use. Copyright © 2016 Elsevier Inc. All rights reserved.

A pilot study on the effects of individually tailored education for MMR vaccine-hesitant parents on MMR vaccination intention

PubMed Central

Gowda, Charitha; Schaffer, Sarah E.; Kopec, Kristin; Markel, Arielle; Dempsey, Amanda F.

2013-01-01

Healthcare providers need strategies to better address the concerns of vaccine-hesitant parents. We studied whether individually tailored education was more effective than untailored education at improving vaccination intention among MMR vaccine-hesitant parents. In an intervention pilot study of parents (n = 77) of children < 6 y who screened as hesitant to vaccinate against MMR (first or second dose), parents were randomly assigned to receive either (1) educational web pages that were individually tailored to address their specific vaccine concerns; or (2) web pages similar in appearance to the intervention but containing untailored information. The main outcome, change in vaccination intention before and after the intervention, was assessed using an 11-pt scale (higher values indicated greater intent). We found that a greater proportion of parents in the tailored than untailored arm had positive vaccination intentions after viewing educational information (58% vs. 46%). Furthermore, parents in the tailored group had a greater magnitude of change in vaccination intention (1.08 vs. 0.49 points) than participants in the untailored group. However, neither of these results was statistically significant. From this pilot study we conclude message tailoring may be an effective way to improve vaccine compliance among vaccine hesitant parents. However, larger studies are warranted to further investigate the efficacy of providing tailored education for increasing vaccine acceptance among parents with diverse beliefs. PMID:23291937

User-Centered Design of the eyeGuide, a Tailored Glaucoma Behavior Change Program

PubMed Central

Killeen, Olivia; MacKenzie, Chamisa; Heisler, Michele; Resnicow, Ken; Lee, Paul P.; Newman-Casey, Paula Anne

2016-01-01

PURPOSE We employed user-centered design to refine a prototype of the eyeGuide, a novel, tailored behavior change program intended to improve medication adherence among glaucoma patients. PATIENTS Glaucoma patients ≥ age 40 prescribed ≥1 glaucoma medication were included. METHODS The eyeGuide consists of tailored educational content and tailored testimonials in which patients share how they were able to overcome barriers to improve their medication adherence. A hybrid of semi-structured diagnostic and pre-testing interviews were used to refine the content of the eyeGuide. Purposeful sampling was used to recruit a study population representative of the glaucoma patient population. Interviews were conducted until thematic saturation was reached. Interviews were audio recorded and transcribed verbatim. Three researchers analyzed the transcripts, generated a codebook and identified key themes using NVivo 10.0 to further refine the eyeGuide. RESULTS Twenty-one glaucoma patients were interviewed; mean age 72 ± 12.4 years, five (24%) African-Americans, nine (43%) with poor self-reported adherence, ten (47.6%) ≥ age 75, ten (47.6%) with poor vision and nine (42.9%) women. Qualitative analysis identified five important themes for improving glaucoma self-management: social support, patient-provider relationship, medication routine, patients’ beliefs about disease and treatment, and eye drop instillation. All participants expressed satisfaction with in-person delivery of the eyeGuide and preferred this to a web-based module. Participant feedback resulted in revised content. CONCLUSIONS User-centered design generated improvements in the eyeGuide that would not have been possible without patient input. Participants expressed satisfaction with the tailored content. PMID:27096721

Enabling Tailored Music Programs in Elementary Schools: An Australian Exemplar

ERIC Educational Resources Information Center

McFerran, Katrina Skewes; Crooke, Alexander Hew Dale

2014-01-01

Participation in meaningful school music programs is the right of all children. Although music education is widely supported by policy, significant gaps exist in practice in most developed Western countries. These gaps mean the extrinsic and intrinsic benefits associated with participation in tailored programs are not equally available to all…

Supporting Multiple Cognitive Processing Styles Using Tailored Support Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tuan Q. Tran; Karen M. Feigh; Amy R. Pritchett

According to theories of cognitive processing style or cognitive control mode, human performance is more effective when an individual’s cognitive state (e.g., intuition/scramble vs. deliberate/strategic) matches his/her ecological constraints or context (e.g., utilize intuition to strive for a "good-enough" response instead of deliberating for the "best" response under high time pressure). Ill-mapping between cognitive state and ecological constraints are believed to lead to degraded task performance. Consequently, incorporating support systems which are designed to specifically address multiple cognitive and functional states e.g., high workload, stress, boredom, and initiate appropriate mitigation strategies (e.g., reduce information load) is essential to reduce plantmore » risk. Utilizing the concept of Cognitive Control Models, this paper will discuss the importance of tailoring support systems to match an operator's cognitive state, and will further discuss the importance of these ecological constraints in selecting and implementing mitigation strategies for safe and effective system performance. An example from the nuclear power plant industry illustrating how a support system might be tailored to support different cognitive states is included.« less

Process for preparing energetic materials

DOEpatents

Simpson, Randall L [Livermore, CA; Lee, Ronald S [Livermore, CA; Tillotson, Thomas M [Tracy, CA; Hrubesh, Lawrence W [Pleasanton, CA; Swansiger, Rosalind W [Livermore, CA; Fox, Glenn A [Livermore, CA

2011-12-13

Sol-gel chemistry is used for the preparation of energetic materials (explosives, propellants and pyrotechnics) with improved homogeneity, and/or which can be cast to near-net shape, and/or made into precision molding powders. The sol-gel method is a synthetic chemical process where reactive monomers are mixed into a solution, polymerization occurs leading to a highly cross-linked three dimensional solid network resulting in a gel. The energetic materials can be incorporated during the formation of the solution or during the gel stage of the process. The composition, pore, and primary particle sizes, gel time, surface areas, and density may be tailored and controlled by the solution chemistry. The gel is then dried using supercritical extraction to produce a highly porous low density aerogel or by controlled slow evaporation to produce a xerogel. Applying stress during the extraction phase can result in high density materials. Thus, the sol-gel method can be used for precision detonator explosive manufacturing as well as producing precision explosives, propellants, and pyrotechnics, along with high power composite energetic materials.

Sol-Gel Manufactured Energetic Materials

DOEpatents

Simpson, Randall L.; Lee, Ronald S.; Tillotson, Thomas M.; Hrubesh, Lawrence W.; Swansiger, Rosalind W.; Fox, Glenn A.

2005-05-17

Sol-gel chemistry is used for the preparation of energetic materials (explosives, propellants and pyrotechnics) with improved homogeneity, and/or which can be cast to near-net shape, and/or made into precision molding powders. The sol-gel method is a synthetic chemical process where reactive monomers are mixed into a solution, polymerization occurs leading to a highly cross-linked three dimensional solid network resulting in a gel. The energetic materials can be incorporated during the formation of the solution or during the gel stage of the process. The composition, pore, and primary particle sizes, gel time, surface areas, and density may be tailored and controlled by the solution chemistry. The gel is then dried using supercritical extraction to produce a highly porous low density aerogel or by controlled slow evaporation to produce a xerogel. Applying stress during the extraction phase can result in high density materials. Thus, the sol-gel method can be used for precision detonator explosive manufacturing as well as producing precision explosives, propellants, and pyrotechnics, along with high power composite energetic materials.

Sol-gel manufactured energetic materials

DOEpatents

Simpson, Randall L.; Lee, Ronald S.; Tillotson, Thomas M.; Hrubesh, Lawrence W.; Swansiger, Rosalind W.; Fox, Glenn A.

2003-12-23

Sol-gel chemistry is used for the preparation of energetic materials (explosives, propellants and pyrotechnics) with improved homogeneity, and/or which can be cast to near-net shape, and/or made into precision molding powders. The sol-gel method is a synthetic chemical process where reactive monomers are mixed into a solution, polymerization occurs leading to a highly cross-linked three dimensional solid network resulting in a gel. The energetic materials can be incorporated during the formation of the solution or during the gel stage of the process. The composition, pore, and primary particle sizes, gel time, surface areas, and density may be tailored and controlled by the solution chemistry. The gel is then dried using supercritical extraction to produce a highly porous low density aerogel or by controlled slow evaporation to produce a xerogel. Applying stress during the extraction phase can result in high density materials. Thus, the sol-gel method can be used for precision detonator explosive manufacturing as well as producing precision explosives, propellants, and pyrotechnics, along with high power composite energetic materials.

Basic needs, stress and the effects of tailored health communication in vulnerable populations.

PubMed

Cappelletti, Erika R; Kreuter, Matthew W; Boyum, Sonia; Thompson, Tess

2015-08-01

This study examined whether unmet basic needs (food, housing, personal and neighborhood safety, money for necessities) and perceived stress affect recall of and response to a tailored print intervention one month later. Participants (N = 372) were adults who had called 2-1-1 Missouri between June 2010 and June 2012. A series of path analyses using Mplus were conducted to explore the relationships among basic needs, perceived stress, number of health referrals received in a tailored intervention, recalling the intervention and contacting a health referral. Participants were mainly women (85%) and African-American (59%) with a mean age of 42.2 years (SD = 13.3; range 19-86); 41% had annual household income <$10 000. Unmet basic needs were positively associated with increased levels of perceived stress, which, in turn, were negatively associated with recalling the intervention and calling any of the health referrals provided. Tailored printed interventions may be less effective in populations with acute unmet basic needs. More broadly, the effectiveness of minimal contact behavioral interventions might be enhanced by simultaneous efforts to address unmet basic needs. © The Author 2015. Published by Oxford University Press. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Tailored scenarios for streamflow climate change impacts based on the perturbation of precipitation and evapotranspiration

NASA Astrophysics Data System (ADS)

Ntegeka, Victor; Willems, Patrick; Baguis, Pierre; Roulin, Emmanuel

2015-04-01

It is advisable to account for a wide range of uncertainty by including the maximum possible number of climate models and scenarios for future impacts. As this is not always feasible, impact assessments are inevitably performed with a limited set of scenarios. The development of tailored scenarios is a challenge that needs more attention as the number of available climate change simulations grows. Whether these scenarios are representative enough for climate change impacts is a question that needs addressing. This study presents a methodology of constructing tailored scenarios for assessing runoff flows including extreme conditions (peak flows) from an ensemble of future climate change signals of precipitation and potential evapotranspiration (ETo) derived from the climate model simulations. The aim of the tailoring process is to formulate scenarios that can optimally represent the uncertainty spectrum of climate scenarios. These tailored scenarios have the advantage of being few in number as well as having a clear description of the seasonal variation of the climate signals, hence allowing easy interpretation of the implications of future changes. The tailoring process requires an analysis of the hydrological impacts from the likely future change signals from all available climate model simulations in a simplified (computationally less expensive) impact model. Historical precipitation and ETo time series are perturbed with the climate change signals based on a quantile perturbation technique that accounts for the changes in extremes. For precipitation, the change in wetday frequency is taken into account using a markov-chain approach. Resulting hydrological impacts from the perturbed time series are then subdivided into high, mean and low hydrological impacts using a quantile change analysis. From this classification, the corresponding precipitation and ETo change factors are back-tracked on a seasonal basis to determine precipitation-ETo covariation. The

Experimental evaluation of tailored chordwise deformable box beam and correlation with theory

NASA Technical Reports Server (NTRS)

Rehfield, Lawrence W.; Zischka, Peter J.; Chang, Stephen; Fentress, Michael L.; Ambur, Damodar R.

1993-01-01

This paper describes an experimental methodology based upon the use of a flexible sling support and load application system that has been created and utilized to evaluate a box beam which incorporates an elastic tailoring technology. The design technique used here for elastically tailoring the composite box beam structure is to produce exaggerated chordwise camber deformation of substantial magnitude to be of practical use in the new composite aircraft wings. The traditional methods such as a four-point bend test to apply constant bending moment with rigid fixtures inhibits the designed chordwise deformation from occurring and, hence, the need for the new test method. The experimental results for global camber and spanwise bending compliances correlate well with theoretical predictions based on a beam-like model.

Ultrashort polarization-tailored bichromatic fields from a CEP-stable white light supercontinuum.

PubMed

Kerbstadt, Stefanie; Timmer, Daniel; Englert, Lars; Bayer, Tim; Wollenhaupt, Matthias

2017-05-29

We apply ultrafast polarization shaping to an ultrabroadband carrier envelope phase (CEP) stable white light supercontinuum to generate polarization-tailored bichromatic laser fields of low-order frequency ratio. The generation of orthogonal linearly and counter-rotating circularly polarized bichromatic fields is achieved by introducing a composite polarizer in the Fourier plane of a 4 f polarization shaper. The resulting Lissajous- and propeller-type polarization profiles are characterized experimentally by cross-correlation trajectories. The scheme provides full control over all bichromatic parameters and allows for individual spectral phase modulation of both colors. Shaper-based CEP control and the generation of tailored bichromatic fields is demonstrated. These bichromatic CEP-stable polarization-shaped ultrashort laser pulses provide a versatile class of waveforms for coherent control experiments.

Patient-tailored self-management intervention for older adults with hypertension in a nursing home.

PubMed

Park, Yeon-Hwan; Chang, HeeKyung; Kim, JinShil; Kwak, Jin Sang

2013-03-01

This study was to evaluate the effects of a patient-tailored self-management intervention on (1) blood pressure control and (2) self-care behaviour, exercise self-efficacy and medication adherence among Korean older hypertensive patients in a nursing home.   Little is known about whether a patient-tailored self-management for nursing home residents with hypertension is likely to advance the care of this growing population worldwide. A non-equivalent comparison group design. Forty-seven patients (23 and 24 in the intervention and comparison groups, respectively) participated in the study. No one withdrew during the eight-week study period. Hypertensive patients in the intervention group received health education and tailored individual counselling for eight weeks to enhance the self-management. The mean age of patients was 77·4 years. Patients were on hypertensive medications for 11·8 years; only 36 of them took medications without assistance. The baseline comparisons of the patients with and without 8-week intervention did not differ for clinical and demographic variables and outcome measures. Blood pressure decreased when comparing the baseline to eight weeks later from baseline; moreover, blood pressure was significantly reduced only in patients who received the intervention. Self-care behaviour and exercise self-efficacy significantly increased over time only in those who were in the intervention group. However, no significant difference was observed in medication adherence between the two groups. Patient-tailored self-management intervention was a practical approach for decreasing blood pressure and increasing self-care behaviour in older hypertensive patients in a nursing home. Further studies are needed to validate these findings using a larger sample with long-term follow-up. A patient-tailored intervention is feasible not only to empower nursing home residents with hypertension for their care, but also to offer a qualified training and guidelines to

Web-based tailored lifestyle programs: exploration of the target group's interests and implications for practice.

PubMed

Verheijden, Marieke W; Jans, Marielle P; Hildebrandt, Vincent H

2008-01-01

An important challenge in Web-based health promotion is to increase the reach of the target audience by taking the target groups' desires into consideration. Data from 505 members of a Dutch Internet panel (representative for Dutch Internet users) were used to asses the target group's interests and needs. 28% participated in Web-based tailored lifestyle programs, 57% expressed an interest in such programs, and 15% expressed no interest. Interest in Web-based programs was predominantly caused by a general interest in lifestyle and online tests. Participation in Web-based tailored lifestyle programs should not take more than 17 minutes per occasion. 84% were interested in follow-up testing after the initial participation. Responders were particularly interested in physical activity and nutrition. Hardly anyone was willing to pay for participation. The results from this study support the use of Web-based tailored lifestyle programs in behavior change efforts.

The Effectiveness of a Web-Based Computer-Tailored Intervention on Workplace Sitting: A Randomized Controlled Trial.

PubMed

De Cocker, Katrien; De Bourdeaudhuij, Ilse; Cardon, Greet; Vandelanotte, Corneel

2016-05-31

Effective interventions to influence workplace sitting are needed, as office-based workers demonstrate high levels of continued sitting, and sitting too much is associated with adverse health effects. Therefore, we developed a theory-driven, Web-based, interactive, computer-tailored intervention aimed at reducing and interrupting sitting at work. The objective of our study was to investigate the effects of this intervention on objectively measured sitting time, standing time, and breaks from sitting, as well as self-reported context-specific sitting among Flemish employees in a field-based approach. Employees (n=213) participated in a 3-group randomized controlled trial that assessed outcomes at baseline, 1-month follow-up, and 3-month follow-up through self-reports. A subsample (n=122) were willing to wear an activity monitor (activPAL) from Monday to Friday. The tailored group received an automated Web-based, computer-tailored intervention including personalized feedback and tips on how to reduce or interrupt workplace sitting. The generic group received an automated Web-based generic advice with tips. The control group was a wait-list control condition, initially receiving no intervention. Intervention effects were tested with repeated-measures multivariate analysis of variance. The tailored intervention was successful in decreasing self-reported total workday sitting (time × group: P<.001), sitting at work (time × group: P<.001), and leisure time sitting (time × group: P=.03), and in increasing objectively measured breaks at work (time × group: P=.07); this was not the case in the other conditions. The changes in self-reported total nonworkday sitting, sitting during transport, television viewing, and personal computer use, objectively measured total sitting time, and sitting and standing time at work did not differ between conditions. Our results point out the significance of computer tailoring for sedentary behavior and its potential use in public health

Sasang Constitutional Medicine as a Holistic Tailored Medicine

PubMed Central

Pham, Duong Duc

2009-01-01

Sasang constitutional medicine (SCM) is a unique traditional Korean therapeutic alternative form of medicine. Based on the Yin and Yang theory and on Confucianism, humans are classified into four constitutions. These differ in terms of (i) sensitivity to certain groups of herbs and medicines, (ii) equilibrium among internal organic functions, (iii) physical features and (iv) psychological characteristics. We propose that two main axes in the physiopathology of SCM (food intake/waste discharge and consuming/storing Qi and body fluids) are equivalent to the process of internal–external exchange and catabolism/anabolism in modern physiology, respectively. We then used this hypothesis to discuss the physiological and pathological principles of SCM. Constitution-based medicine is based on the theory that some medicinal herbs and remedies are only appropriate for certain constitutions and can cause adverse effects in others. The constitutional approach of SCM share the same vision as tailored medicine; an individualized therapy that can minimize the risk of adverse reaction while increasing the efficacy and an individualized self-regulation that can help prevent specific susceptible chronic disease and live healthily. There is still a long way to this goal for both SCM and tailored medicine, but we may benefit from systems approaches such as systems biology. We suggest that constitutional perspective of SCM and our hypothesis of two main processes may provide a novel insight for further studies. PMID:19745007

Sasang constitutional medicine as a holistic tailored medicine.

PubMed

Kim, Jong Yeol; Pham, Duong Duc

2009-09-01

Sasang constitutional medicine (SCM) is a unique traditional Korean therapeutic alternative form of medicine. Based on the Yin and Yang theory and on Confucianism, humans are classified into four constitutions. These differ in terms of (i) sensitivity to certain groups of herbs and medicines, (ii) equilibrium among internal organic functions, (iii) physical features and (iv) psychological characteristics. We propose that two main axes in the physiopathology of SCM (food intake/waste discharge and consuming/storing Qi and body fluids) are equivalent to the process of internal-external exchange and catabolism/anabolism in modern physiology, respectively. We then used this hypothesis to discuss the physiological and pathological principles of SCM. Constitution-based medicine is based on the theory that some medicinal herbs and remedies are only appropriate for certain constitutions and can cause adverse effects in others. The constitutional approach of SCM share the same vision as tailored medicine; an individualized therapy that can minimize the risk of adverse reaction while increasing the efficacy and an individualized self-regulation that can help prevent specific susceptible chronic disease and live healthily. There is still a long way to this goal for both SCM and tailored medicine, but we may benefit from systems approaches such as systems biology. We suggest that constitutional perspective of SCM and our hypothesis of two main processes may provide a novel insight for further studies.

Tailoring and Critical Thinking - Key Principles for Acquisition Success

DTIC Science & Technology

2015-10-01

Defense AT&L: September–October 2015 6 Tailoring and Critical Thinking— Key Principles for Acquisition Success Mike Kotzian, D.M. n Michael Paul...well as program success . 7 Defense AT&L: September–October 2015 The Long Range Anti-Ship Missile Opportunity To ensure DARPA maintains its ability... successful flight demonstra- tions that initially proved the technical approach. Concurrent with these technical accomplishments came two important

Quasi-monoenergetic ion generation by hole-boring radiation pressure acceleration in inhomogeneous plasmas using tailored laser pulses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weng, S. M., E-mail: weng-sm@ile.osaka-u.ac.jp; Murakami, M.; Azechi, H.

It is proposed that laser hole-boring at a steady speed in inhomogeneous overdense plasma can be realized by the use of temporally tailored intense laser pulses, producing high-fluence quasi-monoenergetic ion beams. A general temporal profile of such laser pulses is formulated for arbitrary plasma density distribution. As an example, for a precompressed deuterium-tritium fusion target with an exponentially increasing density profile, its matched laser profile for steady hole-boring is given theoretically and verified numerically by particle-in-cell simulations. Furthermore, we propose to achieve fast ignition by the in-situ hole-boring accelerated ions using a tailored laser pulse. Simulations show that the effectivemore » energy fluence, conversion efficiency, energy spread, and collimation of the resulting ion beam can be significantly improved as compared to those found with un-tailored laser profiles. For the fusion fuel with an areal density of 1.5 g cm{sup –2}, simulation indicates that it is promising to realize fast ion ignition by using a tailored driver pulse with energy about 65 kJ.« less

A systematic review and meta-analysis of face-to-face communication of tailored health messages: implications for practice.

PubMed

Wanyonyi, Kristina L; Themessl-Huber, Markus; Humphris, Gerry; Freeman, Ruth

2011-12-01

To conduct a systematic review of the effect of face-to-face delivered tailored health messages on patient behavior and applications for practice. A systematic literature review and meta-analysis. Systematic searches of a number of electronic databases were conducted and criteria for selection of studies were specified. 6 experimental studies published between 2003 and 2009 were included. The studies were all randomized controlled trials to evaluate the effectiveness of a face-to-face tailored messaging intervention. There were variation in their research design and methods used to randomize. All participants were aged at least 18 years. All of the studies reported positive changes in participants' health behavior with varying degrees of effect size and duration. A meta-analysis of the available data also confirmed an overall positive effect of tailored messaging on participants' health behaviors. The systematic review and the meta-analysis demonstrate a significant and positive effective of face-to-face tailored messaging upon participants' health behaviors. Health practitioners should be encouraged to allot time in their work routines to discover their patients' psycho-social characteristics and felt needs in order that they can provide a tailored health message to enable the patient to adopt health-promoting regimes into their lifestyle. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Tribochemistry of contact interfaces of nanocrystalline molybdenum carbide films

NASA Astrophysics Data System (ADS)

Kumar, D. Dinesh; Kumar, N.; Panda, Kalpataru; Kamalan Kirubaharan, A. M.; Kuppusami, P.

2018-07-01

Transition metal carbides (TMC) are known for their improved tribological properties and are sensitive to the tribo-atmospheric environment. Nanocrystalline molybdenum carbide (MoC) thin films were deposited by DC magnetron sputtering technique using reactive CH4 gas. The friction and wear resistance properties of MoC thin films were significantly improved in humid-atmospheric condition as compared to high-vacuum tribo-condition. A comprehensive chemical analysis of deformed contact interfaces was carried out by X-ray photoelectron spectroscopy (XPS), energy dispersive X-ray spectroscopy (EDX) and Raman spectroscopy. XPS and Raman spectroscopy showed the formation of stable molybdenum-oxide (MoO), molybdenum carbide (MoC) and amorphous carbon (a-C) tribo-phases. Moreover, during the sliding in humid-atmospheric condition, these phases were extensively deposited on the sliding steel ball counter body which significantly protected against undesirable friction and wear.

What’s in a Surname? Physique, Aptitude, and Sports Type Comparisons between Tailors and Smiths

PubMed Central

Voracek, Martin; Rieder, Stephan; Stieger, Stefan; Swami, Viren

2015-01-01

Combined heredity of surnames and physique, coupled with past marriage patterns and trade-specific physical aptitude and selection factors, may have led to differential assortment of bodily characteristics among present-day men with specific trade-reflecting surnames (Tailor vs. Smith). Two studies reported here were partially consistent with this genetic-social hypothesis, first proposed by Bäumler (1980). Study 1 (N = 224) indicated significantly higher self-rated physical aptitude for prototypically strength-related activities (professions, sports, hobbies) in a random sample of Smiths. The counterpart effect (higher aptitude for dexterity-related activities among Tailors) was directionally correct, but not significant, and Tailor-Smith differences in basic physique variables were nil. Study 2 examined two large total-population-of-interest datasets (Austria/Germany combined, and UK: N = 7001 and 20532) of men’s national high-score lists for track-and-field events requiring different physiques. In both datasets, proportions of Smiths significantly increased from light-stature over medium-stature to heavy-stature sports categories. The predicted counterpart effect (decreasing prevalences of Tailors along these categories) was not supported. Related prior findings, the viability of possible alternative interpretations of the evidence (differential positive selection for trades and occupations, differential endogamy and assortative mating patterns, implicit egotism effects), and directions for further inquiry are discussed in conclusion. PMID:26161803

From precision polymers to complex materials and systems

NASA Astrophysics Data System (ADS)

Lutz, Jean-François; Lehn, Jean-Marie; Meijer, E. W.; Matyjaszewski, Krzysztof

2016-05-01

Complex chemical systems, such as living biological matter, are highly organized structures based on discrete molecules in constant dynamic interactions. These natural materials can evolve and adapt to their environment. By contrast, man-made materials exhibit simpler properties. In this Review, we highlight that most of the necessary elements for the development of more complex synthetic matter are available today. Using modern strategies, such as controlled radical polymerizations, supramolecular polymerizations or stepwise synthesis, polymers with precisely controlled molecular structures can be synthesized. Moreover, such tailored polymers can be folded or self-assembled into defined nanoscale morphologies. These self-organized macromolecular objects can be at thermal equilibrium or can be driven out of equilibrium. Recently, in the latter case, interesting dynamic materials have been developed. However, this is just a start, and more complex adaptive materials are anticipated.

Tailoring the properties of a zero-valent iron-based composite by mechanochemistry for nitrophenols degradation in wastewaters.

PubMed

Cagnetta, Giovanni; Huang, Jun; Lomovskiy, Igor O; Yu, Gang

2017-11-01

Zero-valent iron (ZVI) is a valuable material for environmental remediation, because of its safeness, large availability, and inexpensiveness. Moreover, its reactivity can be improved by addition of (nano-) particles of other elements such as noble metals. However, common preparation methods for this kind of iron-based composites involve wet precipitation of noble metal salt precursors, so they are often expensive and not green. Mechanochemical procedures can provide a solvent-free alternative, even at a large scale. The present study demonstrates that it is possible to tailor functional properties of ZVI-based materials, utilizing high-energy ball milling. All main preparation parameters are investigated and discussed. Specifically, a copper-carbon-iron ternary composite was prepared for fast degradation of 4-nitrophenol (utilized as model pollutant) to 4-aminophenol and other phenolic compounds. Copper and carbon are purposely chosen to insert specific properties to the composite: Copper acts as efficient nano-cathode that enhances electron transfer from iron to 4-nitrophenol, while carbon protects the iron surface from fast oxidation in open air. In this way, the reactive material can rapidly reduce high concentration of nitrophenols in water, it does not require acid washing to be activated, and can be stored in open air for one week without any significant activity loss.

A Tensile Specimen of Tailor Rolled Blanks with Equal Probability in Yield and Its Mechanical Behavior Analysis

PubMed Central

Zhang, Sijia; Liu, Xianghua; Liu, Lizhong

2018-01-01

In this paper, the microstructure and mechanical properties that distribute regulation along the rolling direction of tailor rolled blanks (TRB) were investigated. A tensile specimen with equal probability in yield (EYS) was first designed considering variation both in thickness and in material strength. The uniaxial tension test was carried out with a digital image correlation method to analyze the mechanical behaviors. The results showed that the strain distribution of EYS was homogeneous. From the results, it can be known that a new design philosophy for a TRB tensile specimen is reasonable and EYS is suitable to characterize the mechanical behavior of TRB. The true stress-strain curves of metal in different cross sections of TRB were calculated. On the basis of the true stress-strain curves, a material model of TRB was constructed and then implemented into finite element simulations of TRB uniaxial tensile tests. The strain distribution of numerical and experimental results was similar and the error between the elongation of the specimen after fracture obtained by experiment and FE ranged from 9.51% to 13.06%. Therefore, the simulation results match well with the experimental results and the material model has high accuracy and as well as practicability. PMID:29710772

Nerve Conduction Study on Sural Nerve among Nepalese Tailors Using Mechanical Sewing Machine.

PubMed

Yadav, Prakash Kumar; Yadav, Ram Lochan; Sharma, Deepak; Shah, Dev Kumar; Thakur, Dilip; Limbu, Nirmala; Islam, Md Nazrul

2017-03-01

The use of new technologies and innovations are out of access for people living in a developing country like Nepal. The mechanical sewing machine is still in existence at a large scale and dominant all over the country. Tailoring is one of the major occupations adopted by skilled people with lower socioeconomic status and education level. Sural nerves of both right and left legs are exposed to strenuous and chronic stress exerted by chronic paddling of mechanical sewing machine with legs. To evaluate the influence of chronic and strenuous paddling on right and left sural nerves. The study recruited 30 healthy male tailors with median age {34(31-37.25)} years (study group), and, 30 healthy male volunteers with age {34(32-36.25)} years (control group). Anthropometric measurements (age, height, weight, BMI and length of both right and left legs) as well as cardio respiratory measurements [Systolic Blood Pressure (SBP), Dystolic Blood Pressure (DBP), Pules Rate (PR) and Respiratory Rate (RR)] were recorded for each subject. Standard nerve conduction techniques using constant measured distances were applied to evaluate sural nerve (sensory) in both legs of each individual. The differences in variables between the study and control groups were tested using Student's t-test for parametric variables and Mann-Whitney U test for nonparametric variables. A p-value of ≤ 0.05 was considered significant. Age, height, weight, body mass index and leg length were not significantly different between tailors and control groups. Cardio respiratory measurements (SBP, DBP, PR and RR) were also not significantly altered between both the groups. The sensory nerve conduction velocities (m/s) of the right {44.23(42.72-47.83) vs 50(46- 54)} and left sural nerves {45.97±5.86 vs 50.67±6.59} m/s were found significantly reduced in tailors in comparison to control group. Similarly amplitudes (μv) of right sural (20.75±5.42 vs 24.10±5.45) and left sural nerves {18.2(12.43-21.8) vs 32

Response of Damaged and Undamaged Tailored Extension-Shear-Coupled Composite Panels

NASA Technical Reports Server (NTRS)

Baker, Donald J.

2008-01-01

The results of an analytical and experimental investigation of the response of composite I-stiffener panels with extension-shear coupling are presented. This tailored concept, when used in the panel cover skins of a tiltrotor aircraft wing has the potential for increasing the aeroelastic stability margins and improving the aircraft productivity. The extension-shear coupling is achieved by using unbalanced plus or minus 45 deg. plies in the skin. Experimental and STAGS analysis results are compared for eight I-stiffener panel specimens. The results indicate that the tailored concept would be feasible to use in the wing skin of a tiltrotor aircraft. Evaluation of specimens impacted at an energy level of 500 in.-lbs indicate a minimal loss in stiffness and less than 30 percent loss in strength. Evaluation of specimens with severed center stiffener and adjacent skin indicated a strength loss in excess of 60 percent.

Geometric Modeling of Cellular Materials for Additive Manufacturing in Biomedical Field: A Review

PubMed Central

Rosso, Stefano; Meneghello, Roberto; Concheri, Gianmaria

2018-01-01

Advances in additive manufacturing technologies facilitate the fabrication of cellular materials that have tailored functional characteristics. The application of solid freeform fabrication techniques is especially exploited in designing scaffolds for tissue engineering. In this review, firstly, a classification of cellular materials from a geometric point of view is proposed; then, the main approaches on geometric modeling of cellular materials are discussed. Finally, an investigation on porous scaffolds fabricated by additive manufacturing technologies is pointed out. Perspectives in geometric modeling of scaffolds for tissue engineering are also proposed. PMID:29487626

A multifunctional biphasic water splitting catalyst tailored for integration with high-performance semiconductor photoanodes

NASA Astrophysics Data System (ADS)

Yang, Jinhui; Cooper, Jason K.; Toma, Francesca M.; Walczak, Karl A.; Favaro, Marco; Beeman, Jeffrey W.; Hess, Lucas H.; Wang, Cheng; Zhu, Chenhui; Gul, Sheraz; Yano, Junko; Kisielowski, Christian; Schwartzberg, Adam; Sharp, Ian D.

2017-03-01

Artificial photosystems are advanced by the development of conformal catalytic materials that promote desired chemical transformations, while also maintaining stability and minimizing parasitic light absorption for integration on surfaces of semiconductor light absorbers. Here, we demonstrate that multifunctional, nanoscale catalysts that enable high-performance photoelectrochemical energy conversion can be engineered by plasma-enhanced atomic layer deposition. The collective properties of tailored Co3O4/Co(OH)2 thin films simultaneously provide high activity for water splitting, permit efficient interfacial charge transport from semiconductor substrates, and enhance durability of chemically sensitive interfaces. These films comprise compact and continuous nanocrystalline Co3O4 spinel that is impervious to phase transformation and impermeable to ions, thereby providing effective protection of the underlying substrate. Moreover, a secondary phase of structurally disordered and chemically labile Co(OH)2 is introduced to ensure a high concentration of catalytically active sites. Application of this coating to photovoltaic p+n-Si junctions yields best reported performance characteristics for crystalline Si photoanodes.

Solid-State Explosive Reaction for Nanoporous Bulk Thermoelectric Materials.

PubMed

Zhao, Kunpeng; Duan, Haozhi; Raghavendra, Nunna; Qiu, Pengfei; Zeng, Yi; Zhang, Wenqing; Yang, Jihui; Shi, Xun; Chen, Lidong

2017-11-01

High-performance thermoelectric materials require ultralow lattice thermal conductivity typically through either shortening the phonon mean free path or reducing the specific heat. Beyond these two approaches, a new unique, simple, yet ultrafast solid-state explosive reaction is proposed to fabricate nanoporous bulk thermoelectric materials with well-controlled pore sizes and distributions to suppress thermal conductivity. By investigating a wide variety of functional materials, general criteria for solid-state explosive reactions are built upon both thermodynamics and kinetics, and then successfully used to tailor material's microstructures and porosity. A drastic decrease in lattice thermal conductivity down below the minimum value of the fully densified materials and enhancement in thermoelectric figure of merit are achieved in porous bulk materials. This work demonstrates that controlling materials' porosity is a very effective strategy and is easy to be combined with other approaches for optimizing thermoelectric performance. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Tailored Recovery of Carbons from Waste Tires for Enhanced Performance as Anodes in Lithium-ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Naskar, Amit K; Bi,; Saha, Dipendu

2014-01-01

Morphologically tailored pyrolysis-recovered carbon black is utilized in lithium-ion batteries as a potential solution for adding value to waste tire-rubber-derived materials. Micronized tire rubber was digested in a hot oleum bath to yield a sulfonated rubber slurry that was then filtered, washed, and compressed into a solid cake. Carbon was recovered from the modified rubber cake by pyrolysis in a nitrogen atmosphere. The chemical pretreatment of rubber produced a carbon monolith with higher yield than that from the control (a fluffy tire-rubber-derived carbon black). The carbon monolith showed a very small volume fraction of pores of widths 3 4 nm,more » reduced specific surface area, and an ordered assembly of graphitic domains. Electrochemical studies on the recovered-carbon-based anode revealed an improved Li-ion battery performance with higher reversible capacity than that of commercial carbon materials. Anodes made with a sulfonated tire-rubber-derived carbon and a control tire-rubber-derived carbon, respectively, exhibited an initial coulombic efficiency of 80% and 45%, respectively. The reversible capacity of the cell with the sulfonated carbon as anode was 400 mAh/g after 100 cycles, with nearly 100% coulombic efficiency. Our success in producing higher performance carbon material from waste tire rubber for potential use in energy storage applications adds a new avenue to tire rubber recycling.« less

Anti-Mullerian hormone-tailored stimulation protocols improve outcomes whilst reducing adverse effects and costs of IVF.

PubMed

Yates, A P; Rustamov, O; Roberts, S A; Lim, H Y N; Pemberton, P W; Smith, A; Nardo, L G

2011-09-01

Anti-Müllerian hormone (AMH) is increasingly used to quantify ovarian reserve, but it has not yet realized its full clinical potential in assisted reproduction technology. We investigated the possible benefits of using novel, stratified ovarian hyperstimulation protocols, tailored to individual AMH levels, compared with conventional stimulation. Retrospective data were collected from 769 women (first cycle of IVF, using fresh embryos), in a UK tertiary care unit: 346 women using conventional stimulation protocols; 423 women treated under new AMH-tailored protocols. Embryo transfer rates increased significantly (79-87%: P= 0.002) after the introduction of AMH-tailored stimulation protocols. Pregnancy rate per cycle started and live birth rate also increased significantly compared with conventionally treated women (17.9-27.7%, P= 0.002 and 15.9-23.9%, P = 0.007, respectively). Moreover, in the AMH group, the incidence of the ovarian hyperstimulation syndrome (OHSS) fell significantly (6.9-2.3%, P = 0.002) and failed fertilization fell from 7.8 to 4.5%. The cost of fertility drug treatment fell by 29% per patient and the overall cost of clinical management of OHSS fell by 43% in the AMH group. GnRH antagonist protocols, introduced as part of AMH-tailored treatment, may have contributed to the observed improvements: however, within the AMH-tailored group, the live birth rate was not significantly different between agonist and antagonist-treated groups. Although large, prospective, multicentre studies are indicated, we have clearly demonstrated that individualized, AMH-guided, controlled ovarian hyperstimulation protocols significantly improved positive clinical outcomes, reduced the incidence of complications and reduced the financial burden associated with assisted reproduction.

A Coulomb explosion strategy to tailor the nano-architecture of α-MoO3 nanobelts and an insight into its intrinsic mechanism.

PubMed

Zhang, Junli; Zhu, Liu; Yang, Yu; Yong, Huadong; Zhang, Junwei; Peng, Yong; Fu, Jiecai

2018-05-03

Tailoring the nanoarchitecture of materials is significant for the development of nanoscience and nanotechnology. To date, one of the most powerful strategies is convergent electron beam irradiation (EBI). However, only two main functions of knock-on or atomic displacement have been achieved to date. In this study, a Coulomb explosion phenomenon was found to occur in α-MoO3 nanobelts (NBs) under electron beam irradiation, which was controllable and could be used to efficiently create nanostructures such as holes, gaps, and other atomic/nanometer patterns on a single α-MoO3 NB. Theoretical simulations starting from the charging state, charging rate to the threshold time of Coulomb explosion reveal that the Coulomb explosion phenomenon should result from positive charging. The results also show that the multiple charged regions are quickly fragmented, and the monolayered α-MoO3 pieces can then be peeled off once the Coulombic repulsion is sufficient to break the Mo-O bonds in the crystalline structure. It is believed that this efficient and versatile strategy may open up a new avenue to tailor α-MoO3 NBs or other kind of transition metal dichalcogenides via the Coulomb explosion effect.