Performance comparison of various seal coat grades used in Texas.

DOT National Transportation Integrated Search

2012-07-01

This report documents research efforts to provide comparative quantitative performance information for various grades of seal coat aggregate available in the Texas Department of Transportations standard specifications. Length of service before rep...

Guidelines for TxDOT in selecting seal coat materials.

DOT National Transportation Integrated Search

2017-02-01

Aggregates used for seal coats should consist essentially of a single-size stone. When : determining binder application rates in the field, achieving an embedment depth of the stone into : the asphalt binder of about 40 to 50 percent is the goal. If ...

Bioactive Ca-P coating with self-sealing structure on pure magnesium.

PubMed

Gan, Junjie; Tan, Lili; Yang, Ke; Hu, Zhuangqi; Zhang, Qiang; Fan, Xinmin; Li, Yangde; Li, Weirong

2013-04-01

Bioactive coatings containing Ca and P with self-sealing structures were fabricated on the surface of pure magnesium using micro-arc oxidation technique (MAO) in a specific calcium hydroxide based electrolyte system. Coatings were prepared at three applied voltages, i.e. 360, 410 and 450 V, and the morphology, chemical composition, corrosion resistance and the degradation properties in Hank's solution of the MAO-coated samples with three different applied voltages were investigated. It was found that all the three coatings showed similar surface morphologies that the majority of micro-pores were filled with compound particles. Both the porous structures and the compound particles were found to contain consistent chemical compositions which were mainly composed of O, Mg, F, Ca and P. Electrochemical tests showed a significant increase in corrosion resistance for the three coatings, meanwhile the coating obtained at 450 V exhibited the superior corrosion resistance owing to the largest coating thickness. The long term immersion tests in Hank's solution also revealed an effective reduction in corrosion rate for the MAO coated samples, and the pH values of the coated samples always maintained a lower level. Besides, all the three coatings were subjected to a mild and uniform degradation, while the coating obtained at 360 V showed a relatively obvious degradation characteristic and appreciable Ca and P contents on the surfaces of the three coatings were observed after immersion in Hank's solution. The results of the present study confirmed that the MAO coatings containing bioactive Ca and P elements with self-sealing structures could significantly enhance the corrosion resistance of magnesium substrate in Hanks' solution with great potential for medical application.

Intermediate coating layer for high temperature rubbing seals for rotary regenerators

DOEpatents

Schienle, James L.; Strangman, Thomas E.

1995-01-01

A metallic regenerator seal is provided having multi-layer coating comprising a NiCrAlY bond layer, a yttria stabilized zirconia (YSZ) intermediate layer, and a ceramic high temperature solid lubricant surface layer comprising zinc oxide, calcium fluoride, and tin oxide. Because of the YSZ intermediate layer, the coating is thermodynamically stable and resists swelling at high temperatures.

Synthesis study on transverse variable asphalt application rates for seal coats.

DOT National Transportation Integrated Search

2009-06-01

This report documents a cooperative effort to collect, process, and make available information about successful methods of varying seal coat asphalt application rates across treated roadways to optimize aggregate retention and avoid wheel path flushi...

Implementation of transverse variable asphalt rate seal coat practices in Texas.

DOT National Transportation Integrated Search

2011-01-01

An implementation project was performed to expand use of transversely varied asphalt rate (TVAR) seal : coat practices in all districts. The project included nine regional workshops, continued field texture testing of : test sites, provided one set o...

Evaluation of the Texas tier system for seal coat binder specification.

DOT National Transportation Integrated Search

2012-09-01

The Texas Department of Transportation (TxDOT) instituted a change in their seal coat binder specification in 2010 which allowed districts to select multiple binders within specified traffic levels or tiers for the purposes of allowing contractors to...

Relation Between PAHs and Coal-Tar-Based Pavement Sealant in Urban Environments (Invited)

NASA Astrophysics Data System (ADS)

Mahler, B. J.; van Metre, P. C.

2010-12-01

Since 2003, coal-tar-based sealant products have come under increased scrutiny as a source of PAHs in urban environments. Sealant (or sealcoat) is the black, shiny substance often applied to asphalt pavement, in particular parking lots and driveways, for esthetic and maintenance purposes. Coal-tar-based sealant, one of the two primary pavement sealant types on the market, typically is 20-35 percent coal-tar pitch, a known carcinogen that is more than 50 percent polycyclic aromatic hydrocarbons (PAHs). The PAH content of the coal-tar-based sealant product is about 1,000 times that of a similar, asphalt-based product, on average. This difference is reflected in regional differences in sealant use and PAH concentrations in pavement dust. In the central and eastern U.S., where the coal-tar-based formulation is prevalent, ΣPAH in mobile particles from sealed pavement have been shown to be about 1,000 times higher than in the western U.S., where the asphalt-based formulation is prevalent (the median ΣPAH concentrations are 2,200 mg/kg in the central and eastern U.S. and 2.1 mg/kg in the western U.S.). Source apportionment modeling indicates that, in the central and eastern U.S., particles from sealed pavement are contributing the majority of the PAHs in recently deposited (post-1990) lake sediment, with implications for ecological health, and that coal-tar-based sealant is the primary cause of upward trends in PAHs in U.S. urban lakes. From the standpoint of human health, research indicates that mobile particles from parking lots with coal-tar-based sealant are tracked indoors, resulting in elevated PAH concentrations in house dust. Coal-tar-based sealcoat being applied to an asphalt parking lot at the University of Texas Pickle Research Center.

COMPRESSION SEAL AND SEALING MATERIAL THEREFOR

DOEpatents

Branin, T.G.

1962-05-29

This patent relates to compression seal and more particularly to a seaiing material therefor. The sealing surface is a coating consisting of alternate layers of gold and of a non-gold metal having similar plastic flow properties under pressure as gold. The coating is substantially free from oxidation effects when exposed to ambient atmosphere and does not become brittle when worked, as in a valve. (AEC)

Influence of elastomeric seal plate surface chemistry on interface integrity in biofouling-prone systems: Evaluation of a hydrophobic "easy-release" silicone-epoxy coating for maintaining water seal integrity of a sliding neoprene/steel interface

NASA Astrophysics Data System (ADS)

Andolina, Vincent L.

The scientific hypothesis of this work is that modulation of the properties of hard materials to exhibit abrasion-reducing and low-energy surfaces will extend the functional lifetimes of elastomeric seals pressed against them in abrasive underwater systems. The initial motivation of this work was to correct a problem noted in the leaking of seals at major hydropower generating facilities subject to fouling by abrasive zebra mussel shells and extensive corrosion. Similar biofouling-influenced problems can develop at seals in medical devices and appliances from regulators in anesthetic machines and SCUBA diving oxygen supply units to autoclave door seals, injection syringe gaskets, medical pumps, drug delivery components, and feeding devices, as well as in food handling equipment like pasteurizers and transfer lines. Maritime and many other heavy industrial seal interfaces could also benefit from this coating system. Little prior work has been done to elucidate the relationship of seal plate surface properties to the friction and wear of elastomeric seals during sliding contacts of these articulating materials, or to examine the secondary influence of mineralized debris within the contacting interfaces. This investigation utilized the seal materials relevant to the hydropower application---neoprene elastomer against carbon steel---with and without the application of a silicone-epoxy coating (WearlonRTM 2020.98) selected for its wear-resistance, hydrophobicity, and "easy-release" capabilities against biological fouling debris present in actual field use. Analytical techniques applied to these materials before and after wear-producing processes included comprehensive Contact Angle measurements for Critical Surface Tension (CA-CST) determination, Scanning Electron Microscopic inspections, together with Energy Dispersive X-ray Spectroscopy (SEM-EDS) and X-Ray Fluorescence (XRF) measurements for determination of surface texture and inorganic composition, Multiple

Turbomachine Interface Sealing

NASA Technical Reports Server (NTRS)

Hendricks, Robert C.; Chupp, Raymond E.; Lattime, Scott B.; Steinetz, Bruce M.

2005-01-01

Sealing interfaces and coatings, like lubricants, are sacrificial, giving up their integrity for the benefit of the component. Clearance control is a major issue in power systems turbomachine design and operational life. Sealing becomes the most cost-effective way to enhance system performance. Coatings, films, and combined use of both metals and ceramics play a major role in maintaining interface clearances in turbomachine sealing and component life. This paper focuses on conventional and innovative materials and design practices for sealing interfaces.

Coal-tar-based pavement sealants—a potent source of PAHs

USGS Publications Warehouse

Mahler, Barbara J.; Van Metre, Peter C.

2017-01-01

P avement sealants are applied to the asphalt pavement of many parking lots, driveways, and even playgrounds in North America (Figure 1), where, when first applied, they render the pavement glossy black and looking like new. Sealant products used commercially in the central, eastern, and northern United States typically are coal-tarbased, whereas those used in the western United States typically are asphalt-based. Although the products look similar, they are chemically different. Coal-tarbased pavement sealants typically are 25-35 percent (by weight) coal tar or coal-tar pitch, materials that are known human carcinogens and that contain high concentrations of polycyclic aromatic hydrocarbons (PAHs) and related chemicals (unless otherwise noted, all Figure 1. Pavement sealant is commonly used to seal parking lots, playgrounds, and driveways throughout the United States. Sealants used in the central, northern, eastern, and southern United States typically contain coal tar or coal-tar pitch, both of which are known human carcinogens. Photos by the U.S. Geological Survey. data in this article are from Mahler et al. 2012 and references therein).

Coal Tar and Coal-Tar Pitch

Cancer.gov

Learn about coal-tar products, which can raise your risk of skin cancer, lung cancer, and other types of cancer. Examples of coal-tar products include creosote, coal-tar pitch, and certain preparations used to treat skin conditions such as eczema, psoriasis, and dandruff.

Microarc Oxidation Coating Combined with Surface Pore-Sealing Treatment Enhances Corrosion Fatigue Performance of 7075-T7351 Al Alloy in Different Media

PubMed Central

Yang, Hui-Hui; Wang, Xi-Shu; Wang, Ya-Ming; Wang, Yan-Ling; Zhang, Zhi-Hao

2017-01-01

Rotating bending fatigue tests have been performed to evaluate the corrosion fatigue performance and its influence factors of 7075-T7351 Al alloy in different media, namely air and a 5.0 wt % NaCl aqueous solution. All samples were coated by microarc oxidation (MAO) coating technology; some samples were followed by an epoxy resin pore-sealing treatment. Microscopic analyses of the surfaces and fracture cross-sections of samples were carried out. The results reveal that the sample with a MAO coating of 10 μm thickness and pore-sealing treatment by epoxy resin possesses optimal corrosion fatigue performance in the different media. The MAO coating with a pore-sealing treatment significantly improves the corrosion fatigue limit of 7075-T7351 Al alloy. PMID:28772970

Seal glass compatibility with bare and (Mn,Co) 3O 4 coated Crofer 22 APU alloy in different atmospheres

NASA Astrophysics Data System (ADS)

Mahapatra, M. K.; Lu, K.

To prevent gas mixing and leakage during solid oxide fuel/electrolyzer cell operation, the interconnect/seal glass interface should bond well and remain stable. A SrO-La 2O 3-Al 2O 3-SiO 2 (SABS-0) seal glass has been bonded to bare Crofer 22 APU alloy and (Mn,Co) 3O 4 coated Crofer 22 APU alloy. The stability of the interconnect/SABS-0 interface has been studied in air and H 2/H 2O atmospheres at 800 °C for 1000 h. The interconnect/seal glass interaction involves the oxidation of the bare and (Mn,Co) 3O 4 coated Crofer 22 APU alloy surfaces, inter-diffusion of elements, chemical reaction, and the devitrification of the SABS-0 glass. The study shows that the thermal treatment atmosphere greatly affects the interfacial stability of both bare Crofer 22 APU/SABS-0 and (Mn,Co) 3O 4 coated Crofer 22 APU/SABS-0 samples. The interfacial stability is better in the H 2/H 2O atmosphere for both samples. The instability of the (Mn,Co) 3O 4 coating under the thermal treatment conditions degrades the interfacial compatibility of the (Mn,Co) 3O 4 coated Crofer 22 APU/SABS-0 sample.

Maintenance Solutions for Bleeding and Flushed Pavements Surfaced with a Seal Coat or Surface Treatment

DOT National Transportation Integrated Search

2007-02-01

This report summarizes the findings of research directed at identifying maintenance solutions for bleeding and : flushed asphalt pavements surfaced with seal coats or surface treatments. Although the basic mechanism associated with : both bleeding an...

Degradation and biological properties of Ca-P contained micro-arc oxidation self-sealing coating on pure magnesium for bone fixation

PubMed Central

Wang, Weidan; Wan, Peng; Liu, Chen; Tan, Lili; Li, Weirong; Li, Lugee; Yang, Ke

2015-01-01

Poor corrosion resistance is one of the main disadvantages for biodegradable magnesium-based metals, especially applied for bone fixation, where there is a high demand of bio-mechanical strength and stability. Surface coating has been proved as an effective method to control the in vivo degradation. In this study a Ca-P self-sealing micro-arc oxidation (MAO) coating was studied to verify its efficacy and biological properties by in vitro and in vivo tests. It was found that the MAO coating could effectively retard the degradation according to immersion and electrochemical tests as well as 3D reconstruction by X-ray tomography after implantation. The MAO coating exhibited no toxicity and could stimulate the new bone formation. Therefore, the Ca-P self-sealing MAO coating could be a potential candidate for application of biodegradable Mg-based implant in bone fixations. PMID:26816635

DEVELOPMENT OF A CERAMIC TAMPER INDICATING SEAL: SRNL CONTRIBUTIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krementz, D.; Brinkman, K.; Martinez-Rodriguez, M.

2013-06-03

Savannah River National Laboratory (SRNL) and Sandia National Laboratories (SNL) are collaborating on development of a Ceramic Seal, also sometimes designated the Intrinsically Tamper Indicating Ceramic Seal (ITICS), which is a tamper indicating seal for international safeguards applications. The Ceramic Seal is designed to be a replacement for metal loop seals that are currently used by the IAEA and other safeguards organizations. The Ceramic Seal has numerous features that enhance the security of the seal, including a frangible ceramic body, protective and tamper indicating coatings, an intrinsic unique identifier using Laser Surface Authentication, electronics incorporated into the seal that providemore » cryptographic seal authentication, and user-friendly seal wire capture. A second generation prototype of the seal is currently under development whose seal body is of Low Temperature Co-fired Ceramic (LTCC) construction. SRNL has developed the mechanical design of the seal in an iterative process incorporating comments from the SNL vulnerability review team. SRNL is developing fluorescent tamper indicating coatings, with recent development focusing on optimizing the durability of the coatings and working with a vendor to develop a method to apply coatings on a 3-D surface. SRNL performed a study on the effects of radiation on the electronics of the seal and possible radiation shielding techniques to minimize the effects. SRNL is also investigating implementation of Laser Surface Authentication (LSA) as a means of unique identification of each seal and the effects of the surface coatings on the LSA signature.« less

Coal tar phototherapy for psoriasis reevaluated: erythemogenic versus suberythemogenic ultraviolet with a tar extract in oil and crude coal tar

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lowe, N.J.; Wortzman, M.S.; Breeding, J.

1983-06-01

Recent studies have questioned the therapeutic value of coal tar versus ultraviolet (UV) radiation and their relative necessity in phototherapy for psoriasis. In this investigation, different aspects of tar phototherapy have been studied in single-blind bilateral paired comparison studies. The effects of 1% crude coal tar were compared with those of petrolatum in conjunction with erythemogenic and suberythemogenic doses of ultraviolet light (UVB) using a FS72 sunlamp tubed cabinet. Crude coal tar was clinically superior to petrolatum with suberythemogenic ultraviolet. With the erythemogenic UVB, petrolatum was equal in efficacy to crude coal tar. Suberythemogenic UVB was also used adjunctively tomore » compare the effects of a 5% concentration of a tar extract in an oil base to 5% crude coal tar in petrolatum or the oil base without tar. The tar extract in oil plus suberythemogenic UVB produced significantly more rapid improvement than the oil base plus UVB. The direct bilateral comparison of equal concentrations of tar extract in oil base versus crude coal tar in petrolatum in a suberythemogenic UV photo regimen revealed no statistical differences between treatments. In a study comparing tar extract in oil and the oil base without ultraviolet radiation, the tar extract in oil side responded more rapidly.« less

You're standing on it! Coal-tar-based pavement sealcoat and environmental and human health

USGS Publications Warehouse

Mahler, Barbara J.; Van Metre, Peter C.

2013-01-01

Results from a new study by researchers from Baylor University and the USGS indicate that living adjacent to a coal-tar-sealed pavement is associated with significant increases in estimated excess lifetime cancer risk, and that much of the increased risk occurs during early childhood.

Concentrations of polycyclic aromatic hydrocarbons (PAHs) and major and trace elements in simulated rainfall runoff from parking lots, Austin, Texas, 2003

USGS Publications Warehouse

Mahler, Barbara J.; Van Metre, Peter C.; Wilson, Jennifer T.

2004-01-01

Samples of creek bed sediment collected near seal-coated parking lots in Austin, Texas, by the City of Austin during 2001–02 had unusually elevated concentrations of polycyclic aromatic hydrocarbons (PAHs). To investigate the possibility that PAHs from seal-coated parking lots might be transported to urban creeks, the U.S. Geological Survey, in cooperation with the City of Austin, sampled runoff and scrapings from four test plots and 13 urban parking lots. The surfaces sampled comprise coal-tar-emulsion-sealed, asphalt-emulsion-sealed, unsealed asphalt, and unsealed concrete. Particulates and filtered water in runoff and surface scrapings were analyzed for PAHs. In addition, particulates in runoff were analyzed for major and trace elements. Samples of all three media from coal-tar-sealed parking lots had concentrations of PAHs higher than those from any other types of surface. The mean total PAH concentration in particulates in runoff from parking lots in use were 3,500,000, 620,000, and 54,000 micrograms per kilogram from coal-tar-sealed, asphalt-sealed, and unsealed (asphalt and concrete combined) lots, respectively. The probable effect concentration sediment quality guideline is 22,800 micrograms per kilogram. The mean total PAH (sum of detected PAHs) concentration in filtered water from parking lots in use was 8.6 micrograms per liter for coal-tar-sealed lots; the one sample analyzed from an asphalt-sealed lot had a concentration of 5.1 micrograms per liter and the one sample analyzed from an unsealed asphalt lot was 0.24 microgram per liter. The mean total PAH concentration in scrapings was 23,000,000, 820,000, and 14,000 micrograms per kilogram from coal-tar-sealed, asphalt-sealed, and unsealed asphalt lots, respectively. Concentrations of lead and zinc in particulates in runoff frequently exceeded the probable effect concentrations, but trace element concentrations showed no consistent variation with parking lot surface type.

Compliant high temperature seals for dissimilar materials

DOEpatents

Rynders, Steven Walton; Minford, Eric; Tressler, Richard Ernest; Taylor, Dale M.

2001-01-01

A high temperature, gas-tight seal is formed by utilizing one or more compliant metallic toroidal ring sealing elements, where the applied pressure serves to activate the seal, thus improving the quality of the seal. The compliant nature of the sealing element compensates for differences in thermal expansion between the materials to be sealed, and is particularly useful in sealing a metallic member and a ceramic tube art elevated temperatures. The performance of the seal may be improved by coating the sealing element with a soft or flowable coating such as silver or gold and/or by backing the sealing element with a bed of fine powder. The material of the sealing element is chosen such that the element responds to stress elastically, even at elevated temperatures, permitting the seal to operate through multiple thermal cycles.

The Effect of Substrate Contaminates on the Life of Epoxy Coatings Submerged in Sea Water

DTIC Science & Technology

1991-03-01

contaminants: coal tar, SovaPon, Mare Island and Aquapon . Aquapon is a clear (unpigmented) polyamide epoxy coating. While Aquapon is not normally used for...pigmented coatings. It was found that the Aquapon and coal tar coatings performed similarly, and blistered to the same extent, at the contamination levels...used in the test program. The Sovapon and Mare Island coatings were slightly more resistive to blistering when compared to Aquapon or coal tar but they

Sealed-off CO2 laser with In-Au alloy sealing

NASA Astrophysics Data System (ADS)

Iehisa, N.; Fukaya, K.; Karube, N.

1986-02-01

The In-Au alloy sealing was found to satisfy all the requirements imposed on the sealed-off CO2 lasers. The sealing between different materials such as quartz, SUS 303, Si, and ZnSe was shown to withstand the thermal shock test, and gave the He leak rate lower than 1×10-9 atm cc/s both before and after the tests. It was also proved that the transmittance characteristics of dielectric coated output couplers did not change after the sealing. The sealed-off CO2 lasers with La1-xSrxCoO3 perovskite oxide cathodes sealed with this technique produced the operational life of 3000 h at the laser power level of 50 W/m.

Evaluation of quick-dry asphalt paving seal (QDAPS).

DOT National Transportation Integrated Search

1987-10-01

Quick-Dry Asphalt Paving Seal (QDAPS) manufactured for Texas Refinery Corp. Fort Worth, Texas. : According to the manufacturer, the primary use for this product is "a moisture resistant preventative maintenance asphalt coating for coating and sealing...

Chip seal design and specifications : final report.

DOT National Transportation Integrated Search

2016-12-01

Chip seals or seal coats, are a pavement preservation method constructed using a layer of asphalt binder that is covered by a uniformly graded aggregate. The benefits of chip seal include: sealing surface cracks, keeping water from penetrating the su...

Compliant Turbomachine Sealing

NASA Technical Reports Server (NTRS)

Hendricks, R. C.; Braun, M. J.; Deng, D.; Hendricks, J. A.

2011-01-01

Sealing interface materials and coatings are sacrificial, giving up their integrity for the benefit of the component. Seals that are compliant while still controlling leakage, dynamics, and coolant flows are sought to enhance turbomachine performance. Herein we investigate the leaf-seal configuration. While the leaf seal is classified as contacting, a ready modification using the leaf-housing arrangement in conjunction with an interface film rider (a bore seal, for example) provides for a film-riding noncontact seal. The leaf housing and leaf elements can be made from a variety of materials from plastic to ceramic. Four simplistic models are used to identify the physics essential to controlling leakage. Corroborated by CFD, these results provide design parameters for applications to within reasonable engineering certainty. Some potential improvements are proposed.

Coal-Tar-Based Pavement Sealcoat and PAHs: Implications for the Environment, Human Health, and Stormwater Management

PubMed Central

2012-01-01

Coal-tar-based sealcoat products, widely used in the central and eastern U.S. on parking lots, driveways, and even playgrounds, are typically 20−35% coal-tar pitch, a known human carcinogen that contains about 200 polycyclic aromatic hydrocarbon (PAH) compounds. Research continues to identify environmental compartments—including stormwater runoff, lake sediment, soil, house dust, and most recently, air—contaminated by PAHs from coal-tar-based sealcoat and to demonstrate potential risks to biological communities and human health. In many cases, the levels of contamination associated with sealed pavement are striking relative to levels near unsealed pavement: PAH concentrations in air over pavement with freshly applied coal-tar-based sealcoat, for example, were hundreds to thousands of times higher than those in air over unsealed pavement. Even a small amount of sealcoated pavement can be the dominant source of PAHs to sediment in stormwater-retention ponds; proper disposal of such PAH-contaminated sediment can be extremely costly. Several local governments, the District of Columbia, and the State of Washington have banned use of these products, and several national and regional hardware and home-improvement retailers have voluntarily ceased selling them. PMID:22296333

Coal-tar-based pavement sealcoat and PAHs: implications for the environment, human health, and stormwater management

USGS Publications Warehouse

Mahler, Barbara J.; Van Metre, Peter C.; Crane, Judy L.; Watts, Alison W.; Scoggins, Mateo; Williams, E. Spencer

2012-01-01

Coal-tar-based sealcoat products, widely used in the central and eastern U.S. on parking lots, driveways, and even playgrounds, are typically 20-35% coal-tar pitch, a known human carcinogen that contains about 200 polycyclic aromatic hydrocarbon (PAH) compounds. Research continues to identify environmental compartments—including stormwater runoff, lake sediment, soil, house dust, and most recently, air—contaminated by PAHs from coal-tar-based sealcoat and to demonstrate potential risks to biological communities and human health. In many cases, the levels of contamination associated with sealed pavement are striking relative to levels near unsealed pavement: PAH concentrations in air over pavement with freshly applied coal-tar-based sealcoat, for example, were hundreds to thousands of times higher than those in air over unsealed pavement. Even a small amount of sealcoated pavement can be the dominant source of PAHs to sediment in stormwater-retention ponds; proper disposal of such PAH-contaminated sediment can be extremely costly. Several local governments, the District of Columbia, and the State of Washington have banned use of these products, and several national and regional hardware and home-improvement retailers have voluntarily ceased selling them.

Coal-tar-based pavement sealcoat and PAHs: implications for the environment, human health, and stormwater management.

PubMed

Mahler, Barbara J; Metre, Peter C Van; Crane, Judy L; Watts, Alison W; Scoggins, Mateo; Williams, E Spencer

2012-03-20

Coal-tar-based sealcoat products, widely used in the central and eastern U.S. on parking lots, driveways, and even playgrounds, are typically 20-35% coal-tar pitch, a known human carcinogen that contains about 200 polycyclic aromatic hydrocarbon (PAH) compounds. Research continues to identify environmental compartments-including stormwater runoff, lake sediment, soil, house dust, and most recently, air-contaminated by PAHs from coal-tar-based sealcoat and to demonstrate potential risks to biological communities and human health. In many cases, the levels of contamination associated with sealed pavement are striking relative to levels near unsealed pavement: PAH concentrations in air over pavement with freshly applied coal-tar-based sealcoat, for example, were hundreds to thousands of times higher than those in air over unsealed pavement. Even a small amount of sealcoated pavement can be the dominant source of PAHs to sediment in stormwater-retention ponds; proper disposal of such PAH-contaminated sediment can be extremely costly. Several local governments, the District of Columbia, and the State of Washington have banned use of these products, and several national and regional hardware and home-improvement retailers have voluntarily ceased selling them.

Electrophoretically active sol-gel processes to backfill, seal, and/or densify porous, flawed, and/or cracked coatings on electrically conductive material

DOEpatents

Panitz, Janda K.; Reed, Scott T.; Ashley, Carol S.; Neiser, Richard A.; Moffatt, William C.

1999-01-01

Electrophoretically active sol-gel processes to fill, seal, and/or density porous, flawed, and/or cracked coatings on electrically conductive substrates. Such coatings may be dielectrics, ceramics, or semiconductors and, by the present invention, may have deposited onto and into them sol-gel ceramic precursor compounds which are subsequently converted to sol-gel ceramics to yield composite materials with various tailored properties.

Low-tar and high-tar cigarettes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holt, P.G.; Chalmer, J.E.; Roberts, L.M.

Mice were exposed for 7 to 8 minutes on weekdays to fresh smoke from high-tar (HT) or low-tar (LT) cigarettes for varying periods of up to 36 weeks. Mice exposed to HT cigarettes exhibited more marked alterations in humoral immune responsiveness, hematological profiles, and pulmonary pathologic findings than those exposed to LT cigarettes. However, cell-mediated immune responsiveness to both bacterial and tumor-specific antigens was depressed similarly in animals exposed to HT or LT cigarettes. Furthermore, the growth rates of subcutaneously established tumors were enhanced similarly in the two groups, with respect to those in control animals.

Formation mechanism, degradation behavior, and cytocompatibility of a nanorod-shaped HA and pore-sealed MgO bilayer coating on magnesium.

PubMed

Li, Bo; Han, Yong; Qi, Kai

2014-10-22

A novel bilayer coating (HT24h) was fabricated on magnesium using microarc oxidation (MAO) and hydrothermal treatment (HT). The coating comprises an outer layer of narrow interrod spaced hydroxyapatite (HA) nanorods and an inner layer of MgO containing Mg(OH)2/HA-sealing-pores. The hydrothermal formation mechanism of HA nanorods on MAO-formed MgO was explored. Also, evolution of structure and bonding integrity of HT24h coating with immersion in physiological saline (PS) for 0-90 days, corrosion resistance and cytocompatibility of the coating were investigated, together with MgO containing Mg(OH)2-sealing-pores (HT2h) and porous MgO (MAO) coatings. Corrosion resistance was identified by three-point bending and electrochemical tests in PS, while cytocompatibility was determined by MTT, live/dead staining, and vinculin-actin-nucleus tricolor staining assays of hFOB1.19 cells. Immersion tests indicate that cracking rather than delamination is a common feature in most areas of the coatings up to day 90 and degradation is the reason for thinning in thickness of the coatings. MAO and HT2h coatings exhibit a significant thinning due to fast degradation of MgO. However, HT24h coating shows a quite small thinning, owing to the fact that the HA nanorods underwent quite slow degradation while the underlying MgO only underwent conversion to Mg(OH)2 without dissolution of the Mg(OH)2. Scratch tests reveal that HT24h coating still retains relatively high bonding integrity, although the failure position changes from the MgO interior to a point between the HA and MgO layers after 90 days of immersion. HT24h coating appears far more effective than MAO and HT2h coatings in reducing degradation and maintaining the mechanical integrity of Mg, as well as enhancing the mitochondrial activity, adhesion, and proliferation of osteoblasts.

Understanding the fate and transport of petroleum hydrocarbons from coal tar within gasholders.

PubMed

Coulon, Frédéric; Orsi, Roberto; Turner, Claire; Walton, Chris; Daly, Paddy; Pollard, Simon J T

2009-02-01

Coal tars have been identified as posing a threat to human health due to their toxic, mutagenic and carcinogenic characteristics. Workers involved in former gasholders decommissioning are potentially exposed to relevant concentrations of volatile and semi-volatile hydrocarbons upon opening up derelict tanks and during tar excavation/removal. While information on contaminated sites air-quality and its implications on medium-long term exposure is available, acute exposure issues associated with the execution of critical tasks are less understood. Calculations indicated that the concentration of a given contaminant in the gasholder vapour phase only depends on the coal tar composition, being only barely affected by the presence of water in the gasholder and the tar volume/void space ratio. Fugacity modelling suggested that risk-critical compounds such as benzene, naphthalene and other monocyclic and polycyclic aromatic hydrocarbons may gather in the gasholder air phase at significant concentrations. Gasholder emissions were measured on-site and compared with the workplace exposure limits (WELs) currently in use in UK. While levels for most of the toxic compounds were far lower than WELs, benzene air-concentrations where found to be above the accepted threshold. In addition due to the long exposure periods involved in gasholder decommissioning and the significant contribution given by naphthalene to the total coal tar vapour concentration, the adoption of a WEL for naphthalene may need to be considered to support operators in preventing human health risk at the workplace. The Level I fugacity approach used in this study demonstrated its suitability for applications to sealed environments such as gasholders and its further refining could provide a useful tool for land remediation risk assessors.

Electrophoretically active sol-gel processes to backfill, seal, and/or densify porous, flawed, and/or cracked coatings on electrically conductive material

DOEpatents

Panitz, J.K.; Reed, S.T.; Ashley, C.S.; Neiser, R.A.; Moffatt, W.C.

1999-07-20

Electrophoretically active sol-gel processes to fill, seal, and/or density porous, flawed, and/or cracked coatings on electrically conductive substrates. Such coatings may be dielectrics, ceramics, or semiconductors and, by the present invention, may have deposited onto and into them sol-gel ceramic precursor compounds which are subsequently converted to sol-gel ceramics to yield composite materials with various tailored properties. 6 figs.

Topical tar: Back to the future

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paghdal, K.V.; Schwartz, R.A.

2009-08-15

The use of medicinal tar for dermatologic disorders dates back to the ancient times. Although coal tar is utilized more frequently in modern dermatology, wood tars have also been widely employed. Tar is used mainly in the treatment of chronic stable plaque psoriasis, scalp psoriasis, atopic dermatitis, and seborrheic dermatitis, either alone or in combination therapy with other medications, phototherapy, or both. Many modifications have been made to tar preparations to increase their acceptability, as some dislike its odor, messy application, and staining of clothing. One should consider a tried and true treatment with tar that has led to clearingmore » of lesions and prolonged remission times. Occupational studies have demonstrated the carcinogenicity of tar; however, epidemiologic studies do not confirm similar outcomes when used topically. This article will review the pharmacology, formulations, efficacy, and adverse effects of crude coal tar and other tars in the treatment of selected dermatologic conditions.« less

Regenerator seal

DOEpatents

Davis, Leonard C.; Pacala, Theodore; Sippel, George R.

1981-01-01

A method for manufacturing a hot side regenerator cross arm seal assembly having a thermally stablilized wear coating with a substantially flat wear surface thereon to seal between low pressure and high pressure passages to and from the hot inboard side of a rotary regenerator matrix includes the steps of forming a flat cross arm substrate member of high nickel alloy steel; fixedly securing the side edges of the substrate member to a holding fixture with a concave surface thereacross to maintain the substrate member to a slightly bent configuration on the fixture surface between the opposite ends of the substrate member to produce prestress therein; applying coating layers on the substrate member including a wear coating of plasma sprayed nickel oxide/calcium flouride material to define a wear surface of slightly concave form across the restrained substrate member between the free ends thereon; and thereafter subjecting the substrate member and the coating thereon to a heat treatment of 1600.degree. F. for sixteen hours to produce heat stabilizing growth in the coating layers on the substrate member and to produce a thermally induced growth stress in the wear surface that substantially equalizes the prestress in the substrate whereby when the cross arm is removed from the fixture surface following the heat treatment step a wear face is formed on the cross arm assembly that will be substantially flat between the ends.

Anti-diffusion metal coated O-rings

DOEpatents

Biallas, George Herman; Boyce, James Reid

2016-03-22

A method for inhibiting diffusion of gases and/or transmission of photons through elastomeric seals and a diffusion inhibiting elastomeric seal wherein at least a portion of the surface of a diffusion inhibiting elastomeric seal is coated with a compatibly-deformable, malleable metal coating.

Poly-2-methoxyethylacrylate-coated cardiopulmonary bypass circuit can reduce transfusion of platelet products compared to heparin-coated circuit during aortic arch surgery.

PubMed

Hosoyama, Katsuhiro; Ito, Koki; Kawamoto, Shunsuke; Kumagai, Kiichiro; Akiyama, Masatoshi; Adachi, Osamu; Kawatsu, Satoshi; Sasaki, Konosuke; Suzuki, Marina; Sugawara, Yumi; Shimizu, Yuya; Saiki, Yoshikatsu

2016-09-01

Several coating techniques for extracorporeal circulation have been developed to reduce the systemic inflammatory response during cardiopulmonary bypass (CPB). We compared the clinical effectiveness and biocompatibility of poly-2-methoxyethylacrylate (PMEA)- and heparin-coated CPB circuits in total aortic arch replacement (TAR) with the prolonged use of the bypass technique. Twenty patients who underwent elective TAR were divided randomly into two equal groups: group P (n = 10) to use PMEA-coated circuits and group H (n = 10) to use heparin-coated circuits. Clinical outcomes, hematological variables, and acute phase inflammatory response were analyzed perioperatively. Demographic, CPB, and clinical outcome data were similar for both groups. Hemoglobin and platelet count showed similar time-course curves. However, the amount of platelet products transfused intraoperatively was significantly larger in group H (group P 26.0 ± 7.0 units; group H 33.0 ± 6.7 units, p = 0.04). Total protein, and albumin levels were significantly higher in group P during and after the operation (total protein, p = 0.04; albumin, p = 0.02). The use of PMEA-coated circuit is associated with retainment of perioperative plasma proteins levels and may help to reduce transfusion of platelet products in TAR in comparison with the heparin-coated circuit.

Anodizing And Sealing Aluminum In Nonchromated Solutions

NASA Technical Reports Server (NTRS)

Emmons, John R.; Kallenborn, Kelli J.

1995-01-01

Improved process for anodizing and sealing aluminum involves use of 5 volume percent sulfuric acid in water as anodizing solution, and 1.5 to 2.0 volume percent nickel acetate in water as sealing solution. Replaces process in which sulfuric acid used at concentrations of 10 to 20 percent. Improved process yields thinner coats offering resistance to corrosion, fatigue life, and alloy-to-alloy consistency equal to or superior to those of anodized coats produced with chromated solutions.

Performance of thermal sprayed aluminium coatings in the splash zone and for riser service

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fischer, K.P.; Rosbrook, T.; Thomason, W.H.

1994-12-31

Historically, the coatings used in the splash zone have been either heavy duty coal tar epoxy or a glassflake epoxy. In 1982 Conoco justified a minimum 20 year service life for a sealed thermal sprayed aluminium (TSA) coating for the Hutton TLP risers and tethers. In 1984 the Hutton TLP was installed with 200 microns thickness TSA as the corrosion protection coating and without adding a corrosion allowance. After eight years service the TSA coating on the production risers and tethers is still in good condition. It was noted that the splash zone area was indistinguishable from the remainder ofmore » the inspected components. However, there was a noticeable difference between the production risers and the tethers. The tethers having a vinyl sealer showed a blistered surface while the risers with a silicone sealer did not show any blistering. No corrosion has been observed underneath any of the blisters. The importance of adequate sealers in connection with blistering has been documented by testing. The excellent long term performance of TSA coating in the splash zone has been further documented by the results of field studies published in the last few years. These experiences indicate that TSA coatings properly applied and with the use of specific sealer systems may provide a service life in excess of 30 years with no required maintenance.« less

Energy conversion device with improved seal

DOEpatents

Miller, Gerald R.; Virkar, Anil V.

1980-01-01

An energy conversion device comprising an improved sealing member adapted to seal a cation-permeable casing to the remainder of the device. The sealing member comprises a metal substrate which (i) bears a nonconductive and corrosion resistant coating on the major surface to which said casing is sealed, and (ii) is corrugated so as to render it flexible, thereby allowing said member to move relative to said casing without cracking the seal therebetween. Corrugations may be circumferential, radial, or both radial and circumferential so as to form dimples. The corrugated member may be in form of a bellows or in a substantially flat form, such as a disc.

Experimental and analytical study of ceramic-coated turbine-tip shroud seals for small turbine engines

NASA Technical Reports Server (NTRS)

Biesiadny, T. J.; Mcdonald, G. E.; Hendricks, R. C.; Little, J. K.; Robinson, R. A.; Klann, G. A.; Lassow, E. S.

1985-01-01

The results of an experimental and analytical evaluation of ceramic turbine tip shrouds within a small turbine engine operating environment are presented. The ceramic shrouds were subjected to 1001 cycles between idle and high power and steady-state conditions for a total of 57.8 engine hr. Posttest engine inspection revealed mud-flat surface cracking, which was attributed to microcracking under tension with crack penetration to the ceramic and bond coat interface. Sections and micrographs tend to corroborate the thesis. The engine test data provided input to a thermomechanical analysis to predict temperature and stress profiles throughout the ceramic gas-path seal. The analysis predicts cyclic thermal stresses large enough to cause the seal to fail. These stresses are, however, mitigated by inelastic behavior of the shroud materials and by the microfracturing that tensile stresses produce. Microfracturing enhances shroud longevity during early life but provides the failure mechanism during life but provides the failure mechanism during extended life when coupled with the time dependent inelastic materials effects.

Valve seat pores sealed with thermosetting monomer

NASA Technical Reports Server (NTRS)

Olmore, A. B.

1966-01-01

Hard anodic coating provides a smooth wear resistant value seating surface on a cast aluminum alloy valve body. Vacuum impregnation with a thermosetting monomer, diallyl phthalate, seals the pores on the coating to prevent galvanic corrosion.

Status of Understanding for Seal Materials

NASA Technical Reports Server (NTRS)

Brown, P. F.

1984-01-01

Material selection for mainshaft face and ring seals, labyrinth seals, accessory gearbox face seals, and lip seals are discussed in light of tribology requirements and a given seal application. Carbon graphite has been found to be one of the best sealing materials and it is widely used in current gas turbine mainshaft and accessory gearbox seals. Its popularity is due to its unique combination of properties which consists of dimensional stability, corrosion resistance, low friction, good self lubricating characteristics, high thermal conductivity and low thermal expansion, the latter two properties combining to provide good thermal shock resistance. A brief description of the seals and the requirements they must meet are discussed to provide insight into the limitations and advantages of the seals in containing the lubricant. A forecast is made of the operational requirements of main shaft and gearbox seals for advanced engines and candidate materials and coatings that may satisfy these advanced engine requirements.

Labyrinth seal testing for lift fan engines

NASA Technical Reports Server (NTRS)

Dobek, L. J.

1973-01-01

An abradable buffered labyrinth seal for the control of turbine gas path leakage in a tip-turbine driven lift fan was designed, tested, and analyzed. The seal configuration was not designed to operate in any specific location but was sized to be evaluated in an existing test rig. The final sealing diameter selected was 28 inches. Results of testing indicate that the flow equations predicted seal air flows consistent with measured values. Excellent sealing characteristics of the abradable coating on the stator land were demonstrated when a substantial seal penetration of .030 inch into the land surface was encountered without appreciable wear on the labyrinth knife edges.

Process for hydrogenation of hydrocarbon tars

DOEpatents

Dolbear, Geoffrey E.

1978-07-18

Hydrocarbon tars of high asphaltene content such as tars obtained from pyrolysis of coal are dissolved in a solvent formed from the hydrogenation of the coal tars, and the resultant mixture hydrogenated in the presence of a catalyst at a pressure from about 1500 to 5000 psig at a temperature from about 500.degree. F to about the critical temperature of the solvent to form a light hydrocarbon as a solvent for the tars. Hydrogen content is at least three times the amount of hydrogen consumed.

Coping with heat: function of the natal coat of cape fur seal (Arctocephalus Pusillus Pusillus) pups in maintaining core body temperature.

PubMed

Erdsack, Nicola; Dehnhardt, Guido; Hanke, Wolf

2013-01-01

Cape fur seal (Arctocephalus pusillus) pups spend the first weeks of life exclusively or mainly ashore. They are exposed to intense solar radiation and high temperatures for long time periods, which results in temperatures up to at least 80°C on their black natal coat. To test the hypothesis that the natal coat has a crucial function in coping with these extreme conditions, we investigated the insulating properties of the natal coat in six captive newborn Cape fur seals during the first 50 days after birth. The natal fur differs from the adult fur not only in colour, but also in density, structure, and water repellence. We measured temperature on the fur surface and within the fur, as well as skin and rectal temperature under varying environmental conditions, comparable to the species' habitat. Experiments were designed to not influence the spontaneous behaviour of the pups. Rectal temperature was constant as long as the pups stayed dry, even during long-lasting intense solar radiation for up to 3 h. Skin temperature remained close to rectal temperature as long as the fur was dry, while with wet fur, skin temperature was significantly reduced as well. Our results show that the natal coat provides an effective insulation against overheating. The severely reduced insulation of wet natal fur against cold supports the assumption that the natal fur is an adaptation to the pups' terrestrial phase of life.

Coping with Heat: Function of The Natal Coat of Cape Fur Seal (Arctocephalus Pusillus Pusillus) Pups in Maintaining Core Body Temperature

PubMed Central

Erdsack, Nicola; Dehnhardt, Guido; Hanke, Wolf

2013-01-01

Cape fur seal (Arctocephalus pusillus) pups spend the first weeks of life exclusively or mainly ashore. They are exposed to intense solar radiation and high temperatures for long time periods, which results in temperatures up to at least 80°C on their black natal coat. To test the hypothesis that the natal coat has a crucial function in coping with these extreme conditions, we investigated the insulating properties of the natal coat in six captive newborn Cape fur seals during the first 50 days after birth. The natal fur differs from the adult fur not only in colour, but also in density, structure, and water repellence. We measured temperature on the fur surface and within the fur, as well as skin and rectal temperature under varying environmental conditions, comparable to the species' habitat. Experiments were designed to not influence the spontaneous behaviour of the pups. Rectal temperature was constant as long as the pups stayed dry, even during long-lasting intense solar radiation for up to 3 h. Skin temperature remained close to rectal temperature as long as the fur was dry, while with wet fur, skin temperature was significantly reduced as well. Our results show that the natal coat provides an effective insulation against overheating. The severely reduced insulation of wet natal fur against cold supports the assumption that the natal fur is an adaptation to the pups' terrestrial phase of life. PMID:23951287

Method for treatment of tar-bearing fuel gas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frauen, L.L.; Kasper, S.

1986-01-07

A process is described of producing a fuel gas which contains condensable tar vapor when it leaves a gasifier, the improvement wherein the tar-bearing gases are treated to remove tar therefrom. The process consists of: (a) continuously conducting hot fuel gas from a gasifier to and discharging it into a spray chamber where the hot tar-bearing gas is contacted with a fine spray of water thereby cooling the tar vapor and evaporating the water to produce a fog-like dispersion of tar in an atmosphere of fuel gas with the temperature in the spray chamber maintained above the dew point ofmore » water; (b) continuously transferring the fuel gas and the dispersion of tar and water to an electrostatic precipitator and precipitating therein at least most of the condensed tar as a liquid; (c) removing the liquid tar so precipitated and conducting at least most of it to a tar burner; (d) burning the tar with no more than the stoichiometric supply of oxygen provided by air to produce oxygen-free and tar-free hot combustion gases; (e) conducting the hot combustion gases directly into a mixer into which the fuel gas and water vapor flows from the precipitator, thereby adding to the fuel gas the sensible heat of the combustion gases; and (f) conducting the mixture so produced to a place of use as a hot fuel gas mixture.« less

Preventing Cracking of Anodized Coatings

NASA Technical Reports Server (NTRS)

He, Charles C.; Heslin, Thomas M.

1995-01-01

Anodized coatings have been used as optical and thermal surfaces in spacecraft. Particulate contamination from cracked coatings is a concern for many applications. The major cause for the cracking is the difference in the coefficient of thermal expansion between the oxide coatings and the aluminum substrate. The loss of water when the coating is exposed to a vacuum also could induce cracking of the coating. Hot-water sealing was identified as the major cause for the cracking of the coatings because of the large temperature change when the parts were immersed in boiling water and the water was absorbed in the coating. when the hot-water sealing process was eliminated, the cracking resistance of the anodized coatings was greatly improved. Also, it was found that dyed black coatings were more susceptible than clear coatings to cracking during thermo-vacuum cyclings.

Method for sealing remote leaks in an enclosure using an aerosol

DOEpatents

Modera, Mark P.; Carrie, Francois R.

1999-01-01

The invention is a method and device for sealing leaks remotely by means of injecting a previously prepared aerosol into the enclosure being sealed according to a particular sealing efficiency defined by the product of a penetration efficiency and a particle deposition efficiency. By using different limits in the relationship between penetration efficiency and flowrate, the same method according the invention can be used for coating the inside of an enclosure. Specifically the invention is a method and device for preparing, transporting, and depositing a solid phase aerosol to the interior surface of the enclosure relating particle size, particle carrier flow rate, and pressure differential, so that particles deposited there can bridge and substantially seal each leak, with out providing a substantial coating at inside surfaces of the enclosure other than the leak. The particle size and flow parameters can be adjusted to coat the interior of the enclosure (duct) without substantial plugging of the leaks depending on how the particle size and flowrate relationships are chosen.

Experimental study on the sealing clearance between the labyrinth sealing displacer and cylinder in the 10 K G-M refrigerator

NASA Astrophysics Data System (ADS)

Hao, X. H.; Ju, Y. L.; Lu, Y. J.

2011-05-01

The labyrinth sealing displacer has been optimal designed to improve the operating stability and life-time of 10 K G-M refrigerator. The displacer was made of stainless steel 304 or inconel 718, coated with PTFE on its outer surface. Compared to the traditional piston-ring sealing displacer, the sealing clearance between the ridge of the labyrinth sealing displacer and cylinder is critical to the cooling performance of the G-M refrigerator. The displacers with different sealing clearances were experimentally studied, and the optimal clearance was given. The effects of the materials of the displacers and the system charge pressures on the performance of the labyrinth sealing were also tested and analyzed.

Sealing nuclear graphite with pyrolytic carbon

NASA Astrophysics Data System (ADS)

Feng, Shanglei; Xu, Li; Li, Li; Bai, Shuo; Yang, Xinmei; Zhou, Xingtai

2013-10-01

Pyrolytic carbon (PyC) coatings were deposited on IG-110 nuclear graphite by thermal decomposition of methane at ∼1830 °C. The PyC coatings are anisotropic and airtight enough to protect IG-110 nuclear graphite against the permeation of molten fluoride salts and the diffusion of gases. The investigations indicate that the sealing nuclear graphite with PyC coating is a promising method for its application in Molten Salt Reactor (MSR).

CARCINOGENIC EFFECTS IN A/J MICE OF PARTICULATE OF A COAL TAR PAINT USED IN POTABLE WATER SYSTEMS

EPA Science Inventory

Coal tar paints are among the products used as inside coatings for water pipes and storage tanks to retard corrosion in potable water supply systems. Four different formulations of these paints were tested in earlier work by this laboratory in the Ames mutagenesis and the mouse s...

24 CFR 3280.603 - General requirements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... welding, brazing, or soldering or by paint, wax, tar, or other leak-sealing or repairing agents. (v... piping. All piping, pipe threads, hangers, and support exposed to the weather, water, mud, and road hazard, and subject to damage therefrom, shall be painted, coated, wrapped, or otherwise protected from...

24 CFR 3280.603 - General requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... welding, brazing, or soldering or by paint, wax, tar, or other leak-sealing or repairing agents. (v... piping. All piping, pipe threads, hangers, and support exposed to the weather, water, mud, and road hazard, and subject to damage therefrom, shall be painted, coated, wrapped, or otherwise protected from...

24 CFR 3280.603 - General requirements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... welding, brazing, or soldering or by paint, wax, tar, or other leak-sealing or repairing agents. (v... piping. All piping, pipe threads, hangers, and support exposed to the weather, water, mud, and road hazard, and subject to damage therefrom, shall be painted, coated, wrapped, or otherwise protected from...

Steam Turbine Flow Path Seals (a Review)

NASA Astrophysics Data System (ADS)

Neuimin, V. M.

2018-03-01

Various types of shroud, diaphragm, and end seals preventing idle leak of working steam are installed in the flow paths of steam turbine cylinders for improving their efficiency. Widely known labyrinth seals are most extensively used in the Russian turbine construction industry. The category of labyrinth seals also includes seals with honeycomb inserts. The developers of seals with honeycomb inserts state that the use of such seals makes it possible to achieve certain gain due to smaller leaks of working fluid and more reliable operation of the system under the conditions in which the rotor rotating parts may rub against the stator elements. However, a positive effect can only be achieved if the optimal design parameters of the honeycomb structure are fulfilled with due regard to the specific features of its manufacturing technology and provided that this structure is applied in a goal-seeking manner in the seals of steam and gas turbines and compressors without degrading their vibration stability. Calculated and preliminary assessments made by experts testify that the replacement of conventional labyrinth seals by seals with honeycomb inserts alone, due to which the radial gaps in the shroud seal can be decreased from 1.5 to 0.5 mm, allows the turbine cylinder efficiency to be increased at the initial stage by approximately 1% with the corresponding gain in the turbine set power output. The use of rectangular-cellular seals may result, according to estimates made by their developers, in a further improvement of turbine efficiency by 0.5-1.0%. The labor input required to fabricate such seals is six to eight times smaller than that to fabricate labyrinth seals with honeycomb inserts. Recent years have seen the turbine construction companies of the United States and Germany advertising the use of abradable (sealing) coatings (borrowed from the gas turbine construction technology) in the turbine designs instead of labyrinth seals. The most efficient performance of

40 CFR 721.10532 - Tar, brown coal.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Tar, brown coal. 721.10532 Section 721... Tar, brown coal. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as tar, brown coal (PMN P-12-167, CAS No. 101316-83-0) is subject to...

40 CFR 721.10532 - Tar, brown coal.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Tar, brown coal. 721.10532 Section 721... Tar, brown coal. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as tar, brown coal (PMN P-12-167, CAS No. 101316-83-0) is subject to...

Concentrations of polycyclic aromatic hydrocarbons (PAHs) and azaarenes in runoff from coal-tar- and asphalt-sealcoated pavement

USGS Publications Warehouse

Mahler, Barbara J.; Van Metre, Peter C.; Foreman, William T.

2014-01-01

Coal-tar-based sealcoat, used extensively on parking lots and driveways in North America, is a potent source of PAHs. We investigated how concentrations and assemblages of PAHs and azaarenes in runoff from pavement newly sealed with coal-tar-based (CT) or asphalt-based (AS) sealcoat changed over time. Samples of simulated runoff were collected from pavement 5 h to 111 d following application of AS or CT sealcoat. Concentrations of the sum of 16 PAHs (median concentrations of 328 and 35 μg/L for CT and AS runoff, respectively) in runoff varied relatively little, but rapid decreases in concentrations of azaarenes and low molecular weight PAHs were offset by increases in high molecular weight PAHs. The results demonstrate that runoff from CT-sealcoated pavement, in particular, continues to contain elevated concentrations of PAHs long after a 24-h curing time, with implications for the fate, transport, and ecotoxicological effects of contaminants in runoff from CT-sealcoated pavement.

Concentrations of polycyclic aromatic hydrocarbons (PAHs) and azaarenes in runoff from coal-tar- and asphalt-sealcoated pavement.

PubMed

Mahler, Barbara J; Van Metre, Peter C; Foreman, William T

2014-05-01

Coal-tar-based sealcoat, used extensively on parking lots and driveways in North America, is a potent source of PAHs. We investigated how concentrations and assemblages of PAHs and azaarenes in runoff from pavement newly sealed with coal-tar-based (CT) or asphalt-based (AS) sealcoat changed over time. Samples of simulated runoff were collected from pavement 5 h to 111 d following application of AS or CT sealcoat. Concentrations of the sum of 16 PAHs (median concentrations of 328 and 35 μg/L for CT and AS runoff, respectively) in runoff varied relatively little, but rapid decreases in concentrations of azaarenes and low molecular weight PAHs were offset by increases in high molecular weight PAHs. The results demonstrate that runoff from CT-sealcoated pavement, in particular, continues to contain elevated concentrations of PAHs long after a 24-h curing time, with implications for the fate, transport, and ecotoxicological effects of contaminants in runoff from CT-sealcoated pavement. Published by Elsevier Ltd.

Ultra-high pressure waterjets efficient in removing coatings

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-06-01

Little if any thought was given to pipeline rehabilitation 50 years, a time when pipe manufacturers often coated the external diameter of pipe with coal tar to help eliminate corrosion. Unfortunately, contractors rehabilitating these pipelines today encounter major difficulties when attempting to remove coal tar with traditional removal processes. A leading pipeline rehabilitation firm, F.F. Yockey Company, Inc. of Magnolia, Texas, faced a constant challenge stripping coal tar with rotating knives and brushes. The process generated heat that melted the tar and caused the machines to jam. Another problem was the damage to the substrate caused by the friction-based cleaningmore » techniques of rotating knives and brushes. The knives also failed to completely clean the substrate, leaving behind a significant amount of residue. Contractors learned that new coating bonded poorly to the substrates covered with residual contaminants, thus yielding unsatisfactory results. As he looked for a solution, Dick Yockey, president and CEO of R.F. Yockey, began exploring the use of ultra-high pressure waterjet surface preparation equipment. This system involved water pressurized at levels ranging from 35,000 to 55,000 psi. The water travels through small orifices in a high-speed rotating nozzle, forming a cohesive stream of water. This paper reviews the design and performance of this system.« less

Treating tar sands formations with karsted zones

DOEpatents

Vinegar, Harold J.; Karanikas, John Michael

2010-03-09

Methods for treating a tar sands formation are described herein. The tar sands formation may have one or more karsted zones. Methods may include providing heat from one or more heaters to one or more karsted zones of the tar sands formation to mobilize fluids in the formation. At least some of the mobilized fluids may be produced from the formation.

Tar Management and Recycling in Biomass Gasification and Syngas Purification

NASA Astrophysics Data System (ADS)

McCaffrey, Zach

Removal of tars is critical to the design and operation of biomass gasification systems as most syngas utilization processing equipment (e.g. internal combustion engines, gas turbines, fuel cells, and liquid fuel synthesis reactors) have a low tolerance for tar. Capturing and disposal of tar is expensive due to equipment costs, high hazardous waste disposal costs where direct uses cannot be found, and system energy losses incurred. Water scrubbing is an existing technique commonly used in gasification plants to remove contaminants and tar; however using water as the absorbent is non-ideal as tar compounds have low or no water solubility. Hydrophobic solvents can improve scrubber performance and this study evaluated tar solubility in selected solvents using slip-streams of untreated syngas from a laboratory fluidized bed reactor operated on almond composite feedstock using both air and steam gasification. Tar solubility was compared with Hansen's solubility theory to examine the extent to which the tar removal can be predicted. As collection of tar without utilization leads to a hazardous waste problem, the study investigated the effects of recycling tars back into the gasifier for destruction. Prior to experiments conducted on tar capture and recycle, characterizations of the air and steam gasification of the almond composite mix were made. This work aims to provide a better understanding of tar collection and solvent selection for wet scrubbers, and to provide information for designing improved tar management systems for biomass gasification.

Coating Performance in Duluth Superior Harbor. Part 2

DTIC Science & Technology

2012-10-01

tures in fresh water , and nine coatings were evaluated for corrosion protection of CS coupons and I-beams around DSH after 46 and 35 months...following coatings were selected for this evaluation: 1 Aquapure HR* 2 Chevron Phillips 1ZSMV 3 Standard epoxy 4 HumidurML* 5 Wasser MC-zinc/MC-tar* 6...one option for protection of extensive structures in fresh water , and nine coatings were evaluated for corrosion protection of CS coupons and I-beams

Method for filtering solvent and tar sand mixtures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kelterborn, J. C.; Stone, R. A.

1985-09-03

A method for filtering spent tar sands from a bitumen and organic solvent solution comprises separating the solution into two streams wherein the bulk of the coarser spent tar sand is in a first stream and has an average particle size of about 10 to about 100 mesh and the bulk of the finer spent tar sand is in a second stream; producing a filter cake by filtering the coarser spent tar sand from the first stream; and filtering the finer spent tar sand from the second stream with the filter cake. The method is particularly useful for filtering solutionsmore » of bitumen extracted from bitumen containing diatomite, spent diatomite and organic solvent.« less

Shuttle Suppression by Polymer-Sealed Graphene-Coated Polypropylene Separator.

PubMed

Ou, Xuewu; Yu, Yanzi; Wu, Ruizhe; Tyagi, Abhishek; Zhuang, Minghao; Ding, Yao; Abidi, Irfan Haider; Wu, Hengan; Wang, Fengchao; Luo, Zhengtang

2018-02-14

"Shuttle effect" of lithium polysulfides (LiPS) leads to a poor performance and a short cycle life of the Li-S battery, thus limiting their practical application. We demonstrate here that after coating polypropylene (PP) separator with a continuous monolayer graphene, the shuttle effect can be significantly suppressed by limiting the passage of long-chain LiPS. The graphene/PP separator can be further modified by sealing the big holes or pores on graphene with in situ polymerized nylon-66 via an interfacial polymerization reaction between diamine and adipoyl chloride supplied by the aqueous and oil phase, respectively, from each side of the membrane. With this engineered membrane, an initial specific capacity of 1128.4 mAh g -1 at 0.05C is achieved after test in a coin cell, higher than that of 983.2 mAh g -1 with pristine PP, along with increased Coulombic efficiency from 96.0 to 99.9% and enhanced cycling durability. Molecular dynamics simulations attest that the nanopores with appropriate size and structure are effective in acting as a "sieve" to selectively allow only Li + ions to pass through but prevent LiPS from migrating to the anode, consequently alleviating the shuttle effect. Our method provides a facile solution toward the mitigated shuttle effect and eventually contributes to the high performance of Li-S battery.

Some composite bearing and seal materials for gas turbine applications: A review

NASA Technical Reports Server (NTRS)

Sliney, Harold E.

1989-01-01

A review is made of the selection and tribological testing of materials for high-temperature bearings and seals. The goal is to achieve good tribological properties over a wide range of temperatures because bearings and seals must be functional from low temperature start-up conditions on up to the maximum temperatures encountered during engine operation. Plasma sprayed composite coatings with favorable tribological properties from 25 to 900 C are discussed. The performance of these coatings in simple tribological bench tests is described. Examples are also given of their performance in high-speed sliding contact seals and as Stirling cylinder liner materials, and as back up lubricants for compliant foil gas bearings.

Soft metal plating enables hard metal seal to operate successfully in low temperature, high pressure environment

NASA Technical Reports Server (NTRS)

Lamvermeyer, D. J.

1967-01-01

Soft metal plating of hard metal lip seal enables successful operation of seal in a cryogenic fluid line under high pressure. The seal is coated with a thin film of 24 carat gold on the lip area to provide antigall and seal properties.

Final safety assessment of Coal Tar as used in cosmetics.

PubMed

2008-01-01

Coal Tar is a semisolid by-product obtained in the destructive distillation of bituminous coal, which functions in cosmetic products as a cosmetic biocide and denaturant--antidandruff agent is also listed as a function, but this is considered an over-the-counter (OTC) drug use. Coal Tar is a nearly black, viscous liquid, heavier than water, with a naphthalene-like odor and a sharp burning taste, produced in cooking ovens as a by-product in the manufacture of coke. Crude Coal Tar is composed of 48% hydrocarbons, 42% carbon, and 10% water. In 2002, Coal Tar was reported to the Food and Drug Administration (FDA) to be used in four formulations, all of which appear to be OTC drug products. Coal Tar is monographed by the FDA as Category I (safe and effective) OTC drug ingredient for use in the treatment of dandruff, seborrhoea, and psoriasis. Coal Tar is absorbed through the skin of animals and humans and is systemically distributed. In short-term studies, mice fed a diet containing Coal Tar found it unpalatable, but no adverse effects were reported other than weight loss; rats injected with Coal Tar experienced malaise in one study and decreased water intake and increased liver weights in another; rabbits injected with Coal Tar residue experienced eating avoidance, respiratory difficulty, sneezing, and weight loss. In a subchronic neurotoxicity study using mice, a mixture of phenols, cresols, and xylenols at concentrations approximately equal to those expected in Coal Tar extracts produced regionally selective effects, with a rank order of corpus striatum > cerebellum > cerebral cortex. Coal Tar applied to the backs of guinea pigs increases epidermal thickness. Painting female rabbits with tar decreases the absolute and relative weights of the ovaries and decreased the number of interstitial cells in the ovary. Four therapeutic Coal Tar preparations used in the treatment of psoriasis were mutagenic in the Ames assay. Urine and blood from patients treated with Coal Tar

Smokers' knowledge and understanding of advertised tar numbers: health policy implications.

PubMed

Cohen, J B

1996-01-01

This article examines health policy implications of providing smokers with numerical tar yield information in cigarette advertising. Results of a national probability telephone survey regarding smokers' knowledge and understanding of numerical tar yields and deliveries are reported. Few smokers knew the tar level of their own cigarettes (the exception being smokers of 1- to 5-mg tar cigarettes), and a majority could not correctly judge the relative tar levels of cigarettes. Smokers were unsure whether switching to lower-tar cigarettes would reduce their personal health risks. Many smokers relied on absolute numbers in making trade-offs between number of cigarettes smoked and their tar levels, thus confusion machine-rated tar-yields with actual amounts ingested. The wisdom of the present method of providing tar and nicotine numbers in ads and recommendations for modifying the test protocol are now under discussion. This research indicates that these tar numbers and their implications are poorly understood. The paper recommends revisions in tar ratings to make them more useful and a required statement on cigarette packages to more explicitly relate tar levels to major health risks.

Advanced Seal Development for Large Industrial Gas Turbines

NASA Technical Reports Server (NTRS)

Chupp, Raymond E.

2006-01-01

Efforts are in progress to develop advanced sealing for large utility industrial gas turbine engines (combustion turbines). Such seals have been under developed for some time for aero gas turbines. It is desired to transition this technology to combustion turbines. Brush seals, film riding face and circumferential seals, and other dynamic and static sealing approaches are being incorporated into gas turbines for aero applications by several engine manufacturers. These seals replace labyrinth or other seals with significantly reduced leakage rates. For utility industrial gas turbines, leakage reduction with advanced sealing can be even greater with the enormous size of the components. Challenges to transitioning technology include: extremely long operating times between overhauls; infrequent but large radial and axial excursions; difficulty in coating larger components; and maintenance, installation, and durability requirements. Advanced sealing is part of the Advanced Turbine Systems (ATS) engine development being done under a cooperative agreement between Westinghouse and the US Department of Energy, Office of Fossil Energy. Seal development focuses on various types of seals in the 501ATS engine both at dynamic and static locations. Each development includes rig testing of candidate designs and subsequent engine validation testing of prototype seals. This presentation gives an update of the ongoing ATS sealing efforts with special emphasis on brush seals.

The temporal relationship between advertising and sales of low-tar cigarettes.

PubMed

Reed, Mark B; Anderson, Christy M; Burns, David M

2006-12-01

To determine whether a temporal relationship exists between the advertising and sales of low-tar cigarettes. It was hypothesised that increases in the advertising of low-tar cigarettes would precede increases in sales for these cigarettes. The themes of cigarette advertisements were reviewed and coded for 20 low-tar cigarette brands advertised in 13 widely read magazines in the US between 1960 and 1996. These 20 brands represented most of the low-tar cigarette advertisements and cigarette sales from 1967 to 1996. Cigarette sales data were obtained from the 1994 Maxwell report that summarises all cigarette sales from 1925 to 1990. If the advertisement referred to the low-tar attributes of the cigarette advertised, the advertisement was coded as having a low-tar theme and was included in the analysis. Five different graphical presentations of the relationship between the advertising and sales of the 20 low-tar cigarette brands showed a temporal relationship between low-tar advertising and sales for these brands. This relationship was observed for brands that introduced a low-tar alternative into an existing brand family (eg, Marlboro Light) and for new exclusively low-tar brands (eg, Carlton). Despite large increases in the advertising for the exclusively low-tar brands, sales of these brands remained low relative to sales of the low-tar alternative brands. Increases in print advertising of 20 of the most popular low-tar cigarette brands were followed by increases in sales for these cigarettes. Despite increases in the advertising of exclusively low-tar brands in the mid-1970s and early 1980s, the sales of these brands never matched the sales of the low-tar alternative brands. This suggests that it may have been easier to get smokers to switch to low-tar brands within a brand family compared with entirely new low-tar brands. Over the past 30 years, the marketing of low-tar cigarettes as a healthier alternative to higher-tar cigarettes has resulted in these brands

7 CFR 3201.76 - Asphalt and tar removers.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 15 2014-01-01 2014-01-01 false Asphalt and tar removers. 3201.76 Section 3201.76... Designated Items § 3201.76 Asphalt and tar removers. (a) Definition. Cleaning agents designed to remove asphalt or tar from equipment, roads, or other surfaces. (b) Minimum biobased content. The Federal...

7 CFR 3201.76 - Asphalt and tar removers.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 15 2013-01-01 2013-01-01 false Asphalt and tar removers. 3201.76 Section 3201.76... Designated Items § 3201.76 Asphalt and tar removers. (a) Definition. Cleaning agents designed to remove asphalt or tar from equipment, roads, or other surfaces. (b) Minimum biobased content. The Federal...

Corrosion Behavior of an Abradable Seal Coating System

NASA Astrophysics Data System (ADS)

Zhang, Feng; Xu, Cunguan; Lan, Hao; Huang, Chuanbing; Zhou, Yang; Du, Lingzhong; Zhang, Weigang

2014-08-01

A novel NiTi/BN composite abradable coating and two traditional Ni/C and Ni/BN coatings were manufactured with NiAl as the bond layer using thermal spray technology and their corrosion behaviors were investigated. In salt spray corrosion testing of the Ni/BN coating, defective sites of the metal matrix were corroded preferentially. Simulated occlusion experiments and electrochemical tests indicated that migration of ions resulted in pH decrease and Cl- enrichment in defects, and a more aggressive electrolyte led to a decrease of the corrosion potential of the metal inside defects but an increase of the corrosion current density, representing an autocatalytic corrosion process. Moreover, galvanic corrosion between the top and bond coatings of the abradable system was studied via the electrochemical technique. The results showed that, for the NiTi/BN, Ni/BN, and Ni/graphite coatings with a NiAl bond coating, current flow was generated between the anode and cathode. The NiTi/BN coating acted as the cathode due to its passivation, while the Ni/BN and Ni/graphite coatings acted as the anode because of their lower corrosion potential compared with the NiAl coating. The anode suffered serious corrosion damage due to galvanic corrosion, while the cathode corroded only slightly.

Smokers' knowledge and understanding of advertised tar numbers: health policy implications.

PubMed Central

Cohen, J B

1996-01-01

OBJECTIVES. This article examines health policy implications of providing smokers with numerical tar yield information in cigarette advertising. METHODS. Results of a national probability telephone survey regarding smokers' knowledge and understanding of numerical tar yields and deliveries are reported. RESULTS. Few smokers knew the tar level of their own cigarettes (the exception being smokers of 1- to 5-mg tar cigarettes), and a majority could not correctly judge the relative tar levels of cigarettes. Smokers were unsure whether switching to lower-tar cigarettes would reduce their personal health risks. Many smokers relied on absolute numbers in making trade-offs between number of cigarettes smoked and their tar levels, thus confusion machine-rated tar-yields with actual amounts ingested. CONCLUSIONS. The wisdom of the present method of providing tar and nicotine numbers in ads and recommendations for modifying the test protocol are now under discussion. This research indicates that these tar numbers and their implications are poorly understood. The paper recommends revisions in tar ratings to make them more useful and a required statement on cigarette packages to more explicitly relate tar levels to major health risks. PMID:8561236

EFFECT OF AN ADDITIONAL HYDROPHILIC VERSUS HYDROPHOBIC COAT ON THE QUALITY OF DENTINAL SEALING PROVIDED BY TWO-STEP ETCH-AND-RINSE ADHESIVES

PubMed Central

Silva, Safira Marques de Andrade; Carrilho, Marcela Rocha de Oliveira; Marquezini, Luiz; Garcia, Fernanda Cristina Pimentel; Manso, Adriana Pigozzo; Alves, Marcelo Corrêa; de Carvalho, Ricardo Marins

2009-01-01

Objective: To test the hypothesis that the quality of the dentinal sealing provided by two-step etch-and-rinse adhesives cannot be altered by the addition of an extra layer of the respective adhesive or the application of a more hydrophobic, non-solvated resin. Material and Methods: full-crown preparations were acid-etched with phosphoric acid for 15 s and bonded with Adper Single Bond (3M ESPE), Excite DSC (Ivoclar/Vivadent) or Prime & Bond NT (Dentsply). The adhesives were used according to the manufacturers' instructions (control groups) or after application to dentin they were a) covered with an extra coat of each respective system or b) coated with a non-solvated bonding agent (Adper Scotchbond Multi-Purpose Adhesive, 3M ESPE). Fluid flow rate was measured before and after dentin surfaces were acid-etched and bonded with adhesives. Results: None of the adhesives or experimental treatments was capable to block completely the fluid transudation across the treated dentin. Application of an extra coat of the adhesive did not reduce the fluid flow rate of adhesive-bonded dentin (p>0.05). Conversely, the application of a more hydrophobic non-solvated resin resulted in significant reductions in the fluid flow rate (p<0.05) for all tested adhesives. Conclusions: The quality of the dentinal sealing provided by etch-and-rinse adhesives can be significantly improved by the application of a more hydrophobic, non-solvated bonding agent. PMID:19466248

The Australian tar derby: the origins and fate of a low tar harm reduction programme

PubMed Central

King, W; Carter, S; Borland, R; Chapman, S; Gray, N

2003-01-01

Objective: To document the development of the low tar harm reduction programme in Australia, including tobacco industry responses. Data sources: Tobacco industry documents, retail tobacco journals, newspapers, medical journals, and Anti-Cancer Council of Victoria (ACCV) newsletters and archival records. Study selection: Documents on the strategies and knowledge bases of the ACCV, other Australian health authorities, and the tobacco industry. Results: The ACCV built a durable system for measuring and publicising the tar and nicotine yields of Australian cigarettes and influencing their development. The tobacco industry initially sought to block the development of this system but later appeared to cooperate with it, as is evidenced by the current market dominance of low tar brands. However, behind the scenes, the industry used its substantial knowledge advantage regarding compensatory smoking and its ability to re-engineer cigarettes to gain effective control of the system and subvert the ACCV's objectives. Conclusions: Replacement of the low tar programme with new means of minimising the harms from cigarette smoking should be a policy priority for the Australian government. This will require regulation, rather than further voluntary agreements, and stringent monitoring of successor programmes will be necessary. PMID:14645950

Multi-layer coatings

DOEpatents

Maghsoodi, Sina; Brophy, Brenor L.; Abrams, Ze'ev R.; Gonsalves, Peter R.

2016-06-28

Disclosed herein are coating materials and methods for applying a top-layer coating that is durable, abrasion resistant, highly transparent, hydrophobic, low-friction, moisture-sealing, anti-soiling, and self-cleaning to an existing conventional high temperature anti-reflective coating. The top coat imparts superior durability performance and new properties to the under-laying conventional high temperature anti-reflective coating without reducing the anti-reflectiveness of the coating. Methods and data for optimizing the relative thickness of the under-layer high temperature anti-reflective coating and the top-layer thickness for optimizing optical performance are also disclosed.

The temporal relationship between advertising and sales of low‐tar cigarettes

PubMed Central

Reed, Mark B; Anderson, Christy M; Burns, David M

2006-01-01

Objective and hypothesis To determine whether a temporal relationship exists between the advertising and sales of low‐tar cigarettes. It was hypothesised that increases in the advertising of low‐tar cigarettes would precede increases in sales for these cigarettes. Methods The themes of cigarette advertisements were reviewed and coded for 20 low‐tar cigarette brands advertised in 13 widely read magazines in the US between 1960 and 1996. These 20 brands represented most of the low‐tar cigarette advertisements and cigarette sales from 1967 to 1996. Cigarette sales data were obtained from the 1994 Maxwell report that summarises all cigarette sales from 1925 to 1990. If the advertisement referred to the low‐tar attributes of the cigarette advertised, the advertisement was coded as having a low‐tar theme and was included in the analysis. Results Five different graphical presentations of the relationship between the advertising and sales of the 20 low‐tar cigarette brands showed a temporal relationship between low‐tar advertising and sales for these brands. This relationship was observed for brands that introduced a low‐tar alternative into an existing brand family (eg, Marlboro Light) and for new exclusively low‐tar brands (eg, Carlton). Despite large increases in the advertising for the exclusively low‐tar brands, sales of these brands remained low relative to sales of the low‐tar alternative brands. Conclusions Increases in print advertising of 20 of the most popular low‐tar cigarette brands were followed by increases in sales for these cigarettes. Despite increases in the advertising of exclusively low‐tar brands in the mid‐1970s and early 1980s, the sales of these brands never matched the sales of the low‐tar alternative brands. This suggests that it may have been easier to get smokers to switch to low‐tar brands within a brand family compared with entirely new low‐tar brands. Over the past 30 years, the marketing of low‐tar

A parylene coating process for hybrid circuits

NASA Technical Reports Server (NTRS)

1976-01-01

The parylene coating process developed during this program consists of (1) obtaining a hybrid cover with a hole in it, (2) sealing of the circuit with a hole in the cover, (3) parylene coating through the hole with the external leads protected from parylene by appropriate fixturing, and (4) sealing of the hole by soldering a pretinned kovar tab. Development of the above process required optimization of the parylene coater parameters to obtain a uniform consistent coating which could offer adequate protection to the circuits, fixture design for packages of various types, determination of the size of the deposition hole, and the amount of dimer charge per run, a process to hermetically seal the deposition holes and establishment of quality control techniques or acceptance criteria for the deposited film.

Abradable dual-density ceramic turbine seal system

NASA Technical Reports Server (NTRS)

Clingman, D. L.; Schechter, B.; Cross, K. R.; Cavanagh, J. R.

1981-01-01

A plasma sprayed dual density ceramic abradable seal system for direct application to the HPT seal shroud of small gas turbine engines. The system concept is based on the thermal barrier coating and depends upon an additional layer of modified density ceramic material adjacent to the gas flow path to provide the desired abradability. This is achieved by codeposition of inert fillers with yttria stabilized zirconia (YSZ) to interrupt the continuity of the zirconia struture. The investigation of a variety of candidate fillers, with hardness values as low as 2 on Moh's scale, led to the conclusion that solid filler materials in combination with a YSZ matrix, regardless of their hardness values, have a propensity for compacting rather than shearing as originally expected. The observed compaction is accompanied by high energy dissipation in the rub interaction, usually resulting in the adhesive transfer of blade material to the stationary seal member. Two YSZ based coating systems which incorported hollow alumino silicate spheres as density reducing agents were surveyed over the entire range of compositions from 100 percent filler to 100 percent YSZ. Abradability and erosion characteristics were determined, hardness and permeability characterized, and engine experience acquired with several system configurations.

Alternative method for enteric coating of HPMC capsules resulting in ready-to-use enteric-coated capsules.

PubMed

Huyghebaert, Nathalie; Vermeire, An; Remon, Jean Paul

2004-04-01

The aim of this study was to develop an alternative method for enteric coating of HPMC capsules that avoids the sealing step before coating, resulting in ready-to-use enteric-coated capsules for the use in retail or hospital pharmacy or R&D sections of pharmaceutical industry and for the production of enteric-coated heat and moisture sensitive biomaterials. HPMC caps and bodies 00 (Vcaps, Capsugel) were coated separately in a fluid bed apparatus prior to filling (GPCG-1, Glatt) with Eudragit L30D-55 or Eudragit FS 30 D (Röhm), Aqoat AS-HF (Shin-Etsu) and Sureteric (Colorcon), using an optimised coating process. The coated bodies were filled and closed with the coated caps without encountering problems of coating damage. The release in 0.1N HCl after 2h from capsules coated with Eudragit L30D-55, Eudragit FS 30 D, Aqoat AS-HF and Sureteric was 0.6+/-.03, 0.6+/-0.3, 1.2+/-0.2 and 7.3+/-1.9%, respectively. The alternative method was reproducible and offered a way to overcome the time-consuming and expensive sealing step required using the conventional coating procedure. The obtained enteric-coated HPMC capsules can be stored (un)-filled for at least 6 months without loosing enteric properties.

Transverse Aeolian Ridges (TARs) on Mars II: Distributions, orientations, and ages

NASA Astrophysics Data System (ADS)

Berman, Daniel C.; Balme, Matthew R.; Rafkin, Scot C. R.; Zimbelman, James R.

2011-05-01

Transverse Aeolian Ridges (TARs), 10 m scale, ripple-like aeolian bedforms with simple morphology, are widespread on Mars but it is unknown what role they play in Mars' wider sediment cycle. We present the results of a survey of all Mars Global Surveyor Narrow angle images in a pole-to-pole study area, 45° longitude wide. Following on from the classification scheme and preliminary surveys of Balme et al. (Balme, M.R., Berman, D.C., Bourke, M.C., Zimbelman, J.R. [2008a]. Geomorphology 101, 703-720) and Wilson and Zimbelman (Wilson, S.A., Zimbelman, J.R. [2004]. J. Geophys. Res. 109 (E10). doi: 10.1029/2004JE002247) we searched more than 10,000 images, and found that over 2000 reveal at least 5% areal cover by TARs. The mean TAR areal cover in the study area is about 7% (3% in the northern hemisphere and 11% in the southern hemisphere) but TARs are not homogenously distributed - they are concentrated in the mid-low latitudes and almost absent poleward of 35°N and 55°S. We found no clear correlation between TAR distribution and any of thermal inertia, kilometer-scale roughness, or elevation. We did find that TARs are less common at extremes of elevation. We found that TARs are most common near the equator (especially in the vicinity of Meridiani Planum, in which area they have a distinctive "barchan-like" morphology) and in large southern-hemisphere impact craters. TARs in the equatorial band are usually associated with outcrops of layered terrain or steep slopes, hence their relative absence in the northern hemisphere. TARs in the southern hemisphere are most commonly associated with low albedo, intercrater dune fields. We speculate that the mid-latitude mantling terrain (e.g., Mustard, J.F., Cooper, C.D., Rifkin, M.K. [2001]. Nature 412, 411-414; Kreslavsky, M.A., Head, J.W. [2002]. J. Geophys. Res. 29 (15). doi: 10.1029/2002GL015392) could also play a role in covering TARs or inhibiting saltation. We compared TAR distribution with general circulation model (GCM

Unique Tuft Test Facility Dramatically Reduces Brush Seal Development Costs

NASA Technical Reports Server (NTRS)

Fellenstein, James A.

1997-01-01

Brush seals have been incorporated in the latest turbine engines to reduce leakage and improve efficiency. However, the life of these seals is limited by wear. Studies have shown that optimal sealing characteristics for a brush seal occur before the interference fit between the brush and shaft is excessively worn. Research to develop improved tribopairs (brush and coating) with reduced wear and lower friction has been hindered by the lack of an accurate, low-cost, efficient test methodology. Estimated costs for evaluating a new material combination in an engine company seal test program are on the order of $100,000. To address this need, the NASA Lewis Research Center designed, built, and validated a unique, innovative brush seal tuft tester that slides a single tuft of brush seal wire against a rotating shaft under controlled loads, speeds, and temperatures comparable to those in turbine engines. As an initial screening tool, the brush seal tuft tester can tribologicaly evaluate candidate seal materials for 1/10th the cost of full-scale seal tests. Previous to the development of the brush seal tuft tester facility, most relevant tribological data had been obtained from full-scale seal tests conducted primarily to determine seal leakage characteristics. However, from a tribological point of view, these tests included the confounding effects of varying contact pressures, bristle flaring, high-temperature oxidation, and varying bristle contact angles. These confounding effects are overcome in tuft testing. The interface contact pressures can be either constant or varying depending on the tuft mounting device, and bristle wear can be measured optically with inscribed witness marks. In a recent cooperative program with a U.S. turbine engine manufacturer, five metallic wire candidates were tested against a plasma-sprayed Nichrome-bonded chrome carbide. The wire materials used during this collaboration were either nickel-chrome- or cobaltchrome-based superalloys. These

Atmospheric tar balls from biomass burning in Mexico

NASA Astrophysics Data System (ADS)

Adachi, K.; Buseck, P. R.

2009-12-01

Tar balls are spherical, organic aerosol particles that result from biofuel or biomass burning. They absorb sunlight and cause warming of the atmosphere. Although distinctive when viewed with a transmission electron microscope (TEM) because of their spherical shape, much remains to be determined about details of their compositions, occurrences, and generation. Here we aim to characterize the occurrences of tar balls using individual-particle analyses with a TEM and to study their formation in young biomass-burning smoke. The samples were collected using the U.S. Forest Service Twin Otter aircraft during the MILAGRO (Megacity Initiative: Local and Global Research Observations) campaign conducted in March 2006. We analyzed 84 TEM grid samples from ~30 biomass-burning events near Mexico City and over Yucatan. Sixty samples were from young smoke (less than an hour old), and others were from haze that mainly occurred from biomass burning. Tar balls have neither an evident nucleus nor are they normally attached to other particles. They are almost perfectly spherical on TEM grids, indicating that they were solid when collected. It appears as if tar balls consist of lower volatility organic matter than many other organic aerosol particles. On average, 9% by number of biomass-burning aerosol particles were tar balls in samples collected between a few minutes to an hour after emission. On the other hand, samples collected within a few minutes after emission included few or no tar balls. The occurrences and abundances of atmospheric tar balls are important when evaluating the effects of smoke on local and regional climate.

Atmospheric Tar Balls: Particles from Biomass and Biofuel Burning

NASA Technical Reports Server (NTRS)

Posfai, Mihaly; Gelencser, Andras; Simonics, Renata; Arato, Krisztina; Li, Jia; Hobbs, Peter V.; Buseck, Peter R.

2004-01-01

Tar balls are amorphous, carbonaceous spherules that occur in the tropospheric aerosol as a result of biomass and biofuel burning. They form a distinct group of particles with diameters typically between 30 and 500 nm and readily identifiable with electron microscopy. Their lack of a turbostratic microstructure distinguishes them from soot, and their morphology and composition (approximately 90 mol% carbon) renders them distinct from other carbonaceous particles. Tar balls are particularly abundant in slightly aged (minutes to hours old) biomass smoke, indicating that they likely form by gas-to-particle conversion within smoke plumes. The material of tar balls is initially hygroscopic; however, the particles become largely insoluble as a result of free radical polymerization of their organic molecules. Consequently, tar balls are primarily externally mixed with other particle types, and they do not appreciably increase in size during aging. When tar balls coagulate with water-bearing particles, their material may partly dissolve and no longer be recognizable as distinct particles. Tar balls may contain organic compounds that absorb sunlight. They are an important, previously unrecognized type of carbonaceous (organic) atmospheric particle.

Tar, nicotine, and carbon monoxide yields of some Nigerian cigarettes.

PubMed Central

Awotedu, A A; Higenbottam, T W; Onadeko, B O

1983-01-01

Fourteen cigarette brands manufactured in Nigeria in 1981 were analysed to determine the tar, nicotine, and carbon monoxide yields. Five of the brands belonged to the high and middle to high tar category (greater than 22 mg/cigarette) and nine to the middle tar (17-22 mg/cigarette) category. None of the cigarettes was in the low to middle and low tar (less than 17 mg/cigarette) category. The nicotine and carbon monoxide yields were similar to those of European cigarettes. Tobacco companies need to manufacture low tar cigarettes in the Third World as is the practice in the economically developed parts of the world. PMID:6619721

Occurrence of polycyclic aromatic hydrocarbons below coal-tar-sealed parking lots and effects on stream benthic macroinvertebrate communities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scoggins, M.; McClintock, N.L.; Gosselink, L.

2007-12-15

Parking-lot pavement sealants recently have been recognized as a major source of polycyclic aromatic hydrocarbons (PAHs) in urban stream sediments in Austin, Texas. Laboratory and field studies have shown that PAHs in sediments can be toxic to aquatic organisms and can degrade aquatic communities. After identifying increases in concentrations of PAHs in sediments below seal-coated parking lots, we investigated whether the increases had significant effects on stream biota in 5 Austin streams. We sampled sediment chemistry and biological communities above and below the point at which stormwater runoff from the parking lots discharged into the streams, thus providing 5 upstreammore » reference sites and 5 downstream treatment sites. Differences between upstream and downstream concentrations of total PAH ranged from 3.9 to 32 mg/kg. Analysis of the species occurrence data from pool and riffle habitats indicated a significant decrease in community health at the downstream sites, including decreases in richness, intolerant taxa, Diptera taxa, and density. In pool sediments, Chironomidae density was negatively correlated with PAH concentrations, whereas Oligochaeta density responded positively to PAH concentrations. In general, pool taxa responded more strongly than riffle taxa to PAHs, but riffle taxa responded more broadly than pool taxa. Increases in PAH sediment-toxicity units between upstream and downstream sites explained decreases in taxon richness and density in pools between upstream and downstream sites.« less

Method and apparatus for hydrocarbon recovery from tar sands

DOEpatents

Westhoff, J.D.; Harak, A.E.

1988-05-04

A method and apparatus for utilizing tar sands having a broad range of bitumen content is disclosed. More particularly, tar sands are pyrolyzed in a cyclone retort with high temperature gases recycled from the cyclone retort to produce oil and hydrocarbon products. The spent tar sands are then burned at 2000/degree/F in a burner to remove residual char and produce a solid waste that is easily disposable. The process and apparatus have the advantages of being able to utilize tar sands having a broad range of bitumen content and the advantage of producing product gases that are free from combustion gases and thereby have a higher heating value. Another important advantage is rapid pyrolysis of the tar sands in the cyclone so as to effectively utilize smaller sized reactor vessels for reducing capitol and operating costs. 1 fig., 1 tab.

Method and apparatus for hydrocarbon recovery from tar sands

DOEpatents

Westhoff, James D.; Harak, Arnold E.

1989-01-01

A method and apparatus for utilizing tar sands having a broad range of bitumen content is disclosed. More particularly, tar sands are pyrolyzed in a cyclone retort with high temperature gases recycled from the cyclone retort to produce oil and hydrocarbon products. The spent tar sands are then burned at 2000.degree. F. in a burner to remove residual char and produce a solid waste that is easily disposable. The process and apparatus have the advantages of being able to utilize tar sands having a broad range of bitumen content and the advantage of producing product gases that are free from combustion gases and thereby have a higher heating value. Another important advantage is rapid pyrolysis of the tar sands in the cyclone so as to effectively utilize smaller sized reactor vessels for reducing capitol and operating costs.

VAPOR PRESSURES AND HEATS OF VAPORIZATION OF PRIMARY COAL TARS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eric M. Suuberg; Vahur Oja

1997-07-01

This project had as its main focus the determination of vapor pressures of coal pyrolysis tars. It involved performing measurements of these vapor pressures and from them, developing vapor pressure correlations suitable for use in advanced pyrolysis models (those models which explicitly account for mass transport limitations). This report is divided into five main chapters. Each chapter is a relatively stand-alone section. Chapter A reviews the general nature of coal tars and gives a summary of existing vapor pressure correlations for coal tars and model compounds. Chapter B summarizes the main experimental approaches for coal tar preparation and characterization whichmore » have been used throughout the project. Chapter C is concerned with the selection of the model compounds for coal pyrolysis tars and reviews the data available to us on the vapor pressures of high boiling point aromatic compounds. This chapter also deals with the question of identifying factors that govern the vapor pressures of coal tar model materials and their mixtures. Chapter D covers the vapor pressures and heats of vaporization of primary cellulose tars. Chapter E discusses the results of the main focus of this study. In summary, this work provides improved understanding of the volatility of coal and cellulose pyrolysis tars. It has resulted in new experimentally verified vapor pressure correlations for use in pyrolysis models. Further research on this topic should aim at developing general vapor pressure correlations for all coal tars, based on their molecular weight together with certain specific chemical characteristics i.e. hydroxyl group content.« less

Treating tar sands formations with dolomite

DOEpatents

Vinegar, Harold J.; Karanikas, John Michael

2010-06-08

Methods for treating a tar sands formation are described herein. The tar sands formation may include dolomite and hydrocarbons. Methods may include providing heat at less than the decomposition temperature of dolomite from one or more heaters to at least a portion of the formation. At least some of the hydrocarbon fluids are mobilized in the formation. At least some of the hydrocarbon fluids may be produced from the formation.

Oral exposure to commercially available coal tar-based pavement sealcoat induces murine genetic damage and mutations.

PubMed

Long, Alexandra S; Watson, Margaret; Arlt, Volker M; White, Paul A

2016-08-01

Coal tar (CT) is a thick black liquid produced as a by-product of coal carbonization to produce coke or manufactured gas. It is comprised a complex mixture of polycyclic aromatic compounds, including a wide range of polycyclic aromatic hydrocarbons (PAHs), many of which are genotoxic and carcinogenic. CT is used in some pavement sealants (also known as sealcoat), which are applied to pavement in order to seal and beautify the surface. Human exposure is known to occur not only during application, but also as a result of the weathering process, as elevated levels of PAHs have been found in settled house dust in residences adjacent to CT-sealed surfaces. In this study we examined the genotoxicity of an extract of a commercially available CT-based sealcoat in the transgenic Muta™Mouse model. Mice were orally exposed to 3 doses of sealcoat extract daily for 28 days. We evaluated genotoxicity by examining: (1) stable DNA adducts and (2) lacZ mutations in bone marrow, liver, lung, small intestine, and glandular stomach, as well as (3) micronucleated red blood cells. Significant increases were seen for each endpoint and in all tissues. The potency of the response differed across tissues, with the highest frequency of adducts occurring in liver and lung, and the highest frequency of mutations occurring in small intestine. The results of this study are the first demonstration of mammalian genotoxicity following exposure to CT-containing pavement sealcoat. This work provides in vivo evidence to support the contention that there may be adverse health effects in mammals, and potentially in humans, from exposure to coal tar. Environ. Mol. Mutagen. 57:535-545, 2016. © 2016 Her Majesty the Queen in Right of Canada. © 2016 Reproduced with the permission of the Government of Canada.

Ultrasound assisted, thermally activated persulfate oxidation of coal tar DNAPLs.

PubMed

Peng, Libin; Wang, Li; Hu, Xingting; Wu, Peihui; Wang, Xueqing; Huang, Chumei; Wang, Xiangyang; Deng, Dayi

2016-11-15

The feasibility of ultrasound assisted, thermally activated persulfate for effective oxidation of twenty 2-6 ringed coal tar PAHs in a biphasic tar/water system and a triphasic tar/soil/water system were investigated and established. The results indicate that ultrasonic assistance, persulfate and elevated reaction temperature are all required to achieve effective oxidation of coal tar PAHs, while the heating needed can be provided by ultrasonic induced heating as well. Further kinetic analysis reveals that the oxidation of individual PAH in the biphasic tar/water system follows the first-order kinetics, and individual PAH oxidation rate is primary determined by the mass transfer coefficients, tar/water interfacial areas, the aqueous solubility of individual PAH and its concentration in coal tar. Based on the kinetic analysis and experimental results, the contributions of ultrasound, persulfate and elevated reaction temperature to PAHs oxidation were characterized, and the effects of ultrasonic intensity and oxidant dosage on PAHs oxidation efficiency were investigated. In addition, the results indicate that individual PAH degradability is closely related to its reactivity as well, and the high reactivity of 4-6 ringed PAHs substantially improves their degradability. Copyright © 2016 Elsevier B.V. All rights reserved.

Sealed glass coating of high temperature ceramic superconductors

DOEpatents

Wu, Weite; Chu, Cha Y.; Goretta, Kenneth C.; Routbort, Jules L.

1995-01-01

A method and article of manufacture of a lead oxide based glass coating on a high temperature superconductor. The method includes preparing a dispersion of glass powders in a solution, applying the dispersion to the superconductor, drying the dispersion before applying another coating and heating the glass powder dispersion at temperatures below oxygen diffusion onset and above the glass melting point to form a continuous glass coating on the superconductor to establish compressive stresses which enhance the fracture strength of the superconductor.

Fractal-like Tar Ball Aggregates from Wildfire Smoke

DOE Office of Scientific and Technical Information (OSTI.GOV)

Girotto, Giulia; China, Swarup; Bhandari, Janarjan

Tar balls are atmospheric particles abundant in slightly aged biomass burning smoke and have a significant, but highly uncertain, role on Earth's radiative balance. Tar balls are typically detected using electron microscopy; they are resistant to the electron beam, and generally, they are observed as individual spheres. Here, we report new observations of a significant fraction of tar ball aggregates (~27% by number) from samples collected in a plume of the Whitewater-Baldy Complex fire in New Mexico. The structure of these aggregates is fractal-like and follows a scale invariant power law similar to that of soot particles, despite the considerablymore » larger size and smaller number of monomers. We also present observations of tar ball aggregates from four other geographical locations, including from a remote high elevation site in the North Atlantic Ocean. Aggregation affects the particle optical properties and therefore, their climatic impact. We performed numerical simulations based on the observed morphology and estimated the effects of aggregation on the tar balls optical properties. We find that aggregation can enhance single scattering albedo by up to 41%.« less

Study on tar generated from downdraft gasification of oil palm fronds.

PubMed

Atnaw, Samson Mekbib; Kueh, Soo Chuan; Sulaiman, Shaharin Anwar

2014-01-01

One of the most challenging issues concerning the gasification of oil palm fronds (OPF) is the presence of tar and particulates formed during the process considering its high volatile matter content. In this study, a tar sampling train custom built based on standard tar sampling protocols was used to quantify the gravimetric concentration of tar (g/Nm3) in syngas produced from downdraft gasification of OPF. The amount of char, ash, and solid tar produced from the gasification process was measured in order to account for the mass and carbon conversion efficiency. Elemental analysis of the char and solid tar samples was done using ultimate analysis machine, while the relative concentration of the different compounds in the liquid tar was determined making use of a liquid gas chromatography (GC) unit. Average tar concentration of 4.928 g/Nm3 and 1.923 g/Nm3 was obtained for raw gas and cleaned gas samples, respectively. Tar concentration in the raw gas sample was found to be higher compared to results for other biomass materials, which could be attributed to the higher volatile matter percentage of OPF. Average cleaning efficiency of 61% which is comparable to that of sand bed filter and venturi scrubber cleaning systems reported in the literature was obtained for the cleaning system proposed in the current study.

Study on Tar Generated from Downdraft Gasification of Oil Palm Fronds

PubMed Central

Atnaw, Samson Mekbib; Kueh, Soo Chuan; Sulaiman, Shaharin Anwar

2014-01-01

One of the most challenging issues concerning the gasification of oil palm fronds (OPF) is the presence of tar and particulates formed during the process considering its high volatile matter content. In this study, a tar sampling train custom built based on standard tar sampling protocols was used to quantify the gravimetric concentration of tar (g/Nm3) in syngas produced from downdraft gasification of OPF. The amount of char, ash, and solid tar produced from the gasification process was measured in order to account for the mass and carbon conversion efficiency. Elemental analysis of the char and solid tar samples was done using ultimate analysis machine, while the relative concentration of the different compounds in the liquid tar was determined making use of a liquid gas chromatography (GC) unit. Average tar concentration of 4.928 g/Nm3 and 1.923 g/Nm3 was obtained for raw gas and cleaned gas samples, respectively. Tar concentration in the raw gas sample was found to be higher compared to results for other biomass materials, which could be attributed to the higher volatile matter percentage of OPF. Average cleaning efficiency of 61% which is comparable to that of sand bed filter and venturi scrubber cleaning systems reported in the literature was obtained for the cleaning system proposed in the current study. PMID:24526899

Sealed glass coating of high temperature ceramic superconductors

DOEpatents

Wu, W.; Chu, C.Y.; Goretta, K.C.; Routbort, J.L.

1995-05-02

A method and article of manufacture of a lead oxide based glass coating on a high temperature superconductor is disclosed. The method includes preparing a dispersion of glass powders in a solution, applying the dispersion to the superconductor, drying the dispersion before applying another coating and heating the glass powder dispersion at temperatures below oxygen diffusion onset and above the glass melting point to form a continuous glass coating on the superconductor to establish compressive stresses which enhance the fracture strength of the superconductor. 8 figs.

High-temperature seals and lubricants for geothermal rock bits. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hendrickson, R.R.; Winzenried, R.W.; Jones A.H.

1981-04-01

High temperature seals (elastomeric and mechanical) and lubricants were developed specifically for journal-type rock bits to be used in geothermal well drilling. Results at simulated downhole conditions indicate that five selected elastomeric seals (L'Garde No. 267, Utex Nos. 227, 231 and HTCR, and Sandia Glow Discharge Coated Viton) are capable of 288/sup 0/C (500/sup 0/F) service. Two prototype mechanical seals did not achieve the life determined for the elastomeric seals. Six lubricants (Pacer PLX-024 oil, PLX-043 oil, PLX-045 oil, Geobond Oil, and Geobond Grease) demonstrated 316/sup 0/C (600/sup 0/F) capability. Recommendation is made for full-scale simulated geothermal drilling tests utilizingmore » the improved elastomeric seals and lubricants.« less

Sydney Tar Ponds Remediation: Experience to China

ERIC Educational Resources Information Center

Liu, Fan; Bryson, Ken A.

2009-01-01

The infamous "Sydney Tar Ponds" are well known as one of the largest toxic waste sites of Canada, due to almost 100 years of steelmaking in Sydney, a once beautiful and peaceful city located on the east side of Cape Breton Island, Nova Scotia. This article begins with a contextual overview of the Tar Ponds issue including a brief…

Examination of a carton sealing line using a thermographic scanner

NASA Astrophysics Data System (ADS)

Kleinfeld, Jack M.

1999-03-01

The study of the operation and performance of natural gas fired sealing lines for polyethylene coated beverage containers was performed. Both thermal and geometric data was abstracted from the thermal scans and used to characterize the performance of the sealing line. The impact of process operating variables such as line speed and carton to carton spacing was studied. Recommendations for system improvements, instrumentation and process control were made.

Influence of coal-tar sealcoat and other carbonaceous materials on polycyclic aromatic hydrocarbon loading in an urban watershed

USGS Publications Warehouse

Yang, Y.; Van Metre, P.C.; Mahler, B.J.; Wilson, J.T.; Ligouis, B.; Razzaque, M.; Schaeffer, D.J.; Werth, C.J.

2010-01-01

Carbonaceous material (CM) particles are the principal vectors transporting polycyclic aromatic hydrocarbons (PAHs) into urban waters via runoff; however, characteristics of CM particles in urban watersheds and their relative contributions to PAH contamination remain unclear. Our objectives were to identify the sources and distribution of CM particles in an urban watershed and to determine the types of CMs that were the dominant sources of PAHs in the lake and stream sediments. Samples of soils, parking lot and street dust, and streambed and lake sediment were collected from the Lake Como watershed in Fort Worth, Texas. Characteristics of CM particles determined by organic petrography and a significant correlation between PAH concentrations and organic carbon in coal tar, asphalt, and soot indicate that these three CM particle types are the major sources and carriers of PAHs in the watershed. Estimates of the distribution of PAHs in CM particles indicate that coal-tar pitch, usedinsomepavementsealcoats, isadominant source of PAHs in the watershed, and contributes as much as 99% of the PAHs in sealed parking lot dust, 92% in unsealed parking lot dust, 88% in commercial area soil, 71% in streambed sediment, and 84% in surficial lake sediment. ?? 2010 American Chemical Society.

UV-blocking properties of Zn/ZnO coatings on wood deposited by cold plasma spraying at atmospheric pressure

NASA Astrophysics Data System (ADS)

Wallenhorst, L.; Gurău, L.; Gellerich, A.; Militz, H.; Ohms, G.; Viöl, W.

2018-03-01

In this study, artificial ageing of beech wood coated with Zn/ZnO particles by means of a cold plasma spraying process as well as coating systems including a Zn/ZnO layer and additional conventional sealings were examined. As ascertained by colour measurements, the particle coatings significantly decreased UV light-induced discolouration. Even though no significant colour changes were observed for particle-coated and alkyd-sealed samples, ATR-FTIR measurements revealed photocatalytic degradation of the alkyd matrix. In contrast, the polyurethane sealing appeared to be stabilised by the Zn/ZnO coating. Furthermore, morphologic properties of the pure particle coatings were studied by SEM and roughness measurements. SEM measurements confirmed a melting and solidifying process during deposition.

48 CFR Appendix to Part 1252 - Tar Matrix

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Tar Matrix Appendix to Part 1252 Federal Acquisition Regulations System DEPARTMENT OF TRANSPORTATION CLAUSES AND FORMS SOLICITATION PROVISIONS AND CONTRACT CLAUSES Pt. 1252, App. Appendix to Part 1252—Tar Matrix ER27DE05.000...

Effects of Hypervelocity Impacts on Silicone Elastomer Seals and Mating Aluminum Surfaces

NASA Technical Reports Server (NTRS)

deGroh, Henry C., III; Steinetz, Bruce M.

2009-01-01

While in space silicone based elastomer seals planned for use on NASA's Crew Exploration Vehicle (CEV) are exposed to threats from micrometeoroids and orbital debris (MMOD). An understanding of these threats is required to assess risks to the crew, the CEV orbiter, and missions. An Earth based campaign of hypervelocity impacts on small scale seal rings has been done to help estimate MMOD threats to the primary docking seal being developed for the Low Impact Docking System (LIDS). LIDS is being developed to enable the CEV to dock to the ISS (International Space Station) or to Altair (NASA's next lunar lander). The silicone seal on LIDS seals against aluminum alloy flanges on ISS or Altair. Since the integrity of a seal depends on both sealing surfaces, aluminum targets were also impacted. The variables considered in this study included projectile mass, density, speed, incidence angle, seal materials, and target surface treatments and coatings. Most of the impacts used a velocity near 8 km/s and spherical aluminum projectiles (density = 2.7 g/cubic centimeter), however, a few tests were done near 5.6 km/s. Tests were also performed using projectile densities of 7.7, 2.79, 2.5 or 1.14 g/cubic centimeter. Projectile incidence angles examined included 0 degrees, 45 degrees , and 60 degrees from normal to the plane of the target. Elastomer compounds impacted include Parker's S0383-70 and Esterline's ELA-SA-401 in the as received condition, or after an atomic oxygen treatment. Bare, anodized and nickel coated aluminum targets were tested simulating the candidate mating seal surface materials. After impact, seals and aluminum plates were leak tested: damaged seals were tested against an undamaged aluminum plate; and undamaged seals were placed at various locations over craters in aluminum plates. It has been shown that silicone elastomer seals can withstand an impressive level of damage before leaking beyond allowable limits. In general on the tests performed to date, the

Effects of Hypervelocity Impacts on Silicone Elastomer Seals and Mating Aluminum Surfaces

NASA Technical Reports Server (NTRS)

deGroh, Henry C., III; Steinetz, Bruce M.

2009-01-01

While in space silicone based elastomer seals planned for use on NASA's Crew Exploration Vehicle (CEV) are exposed to threats from micrometeoroids and orbital debris (MMOD). An understanding of these threats is required to assess risks to the crew, the CEV orbiter, and missions. An Earth based campaign of hypervelocity impacts on small scale seal rings has been done to help estimate MMOD threats to the primary docking seal being developed for the Low Impact Docking System (LIDS). LIDS is being developed to enable the CEV to dock to the ISS (International Space Station) or to Altair (NASA's next lunar lander). The silicone seal on LIDS seals against aluminum alloy flanges on ISS or Altair. Since the integrity of a seal depends on both sealing surfaces, aluminum targets were also impacted. The variables considered in this study included projectile mass, density, speed, incidence angle, seal materials, and target surface treatments and coatings. Most of the impacts used a velocity near 8 km/s and spherical aluminum projectiles (density = 2.7 g/cubic cm), however, a few tests were done near 5.6 km/s. Tests were also performed using projectile densities of 7.7, 2.79, 2.5 or 1.14 g/cubic cm. Projectile incidence angles examined included 0 deg, 45 deg, and 60 deg from normal to the plane of the target. Elastomer compounds impacted include Parker's S0383-70 and Esterline's ELA-SA-401 in the as received condition, or after an atomic oxygen treatment. Bare, anodized and nickel coated aluminum targets were tested simulating the candidate mating seal surface materials. After impact, seals and aluminum plates were leak tested: damaged seals were tested against an undamaged aluminum plate; and undamaged seals were placed at various locations over craters in aluminum plates. It has been shown that silicone elastomer seals can withstand an impressive level of damage before leaking beyond allowable limits. In general on the tests performed to date, the diameter of the crater in

Integrated Biomass Gasification with Catalytic Partial Oxidation for Selective Tar Conversion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Lingzhi; Wei, Wei; Manke, Jeff

Biomass gasification is a flexible and efficient way of utilizing widely available domestic renewable resources. Syngas from biomass has the potential for biofuels production, which will enhance energy security and environmental benefits. Additionally, with the successful development of low Btu fuel engines (e.g. GE Jenbacher engines), syngas from biomass can be efficiently used for power/heat co-generation. However, biomass gasification has not been widely commercialized because of a number of technical/economic issues related to gasifier design and syngas cleanup. Biomass gasification, due to its scale limitation, cannot afford to use pure oxygen as the gasification agent that used in coal gasification.more » Because, it uses air instead of oxygen, the biomass gasification temperature is much lower than well-understood coal gasification. The low temperature leads to a lot of tar formation and the tar can gum up the downstream equipment. Thus, the biomass gasification tar removal is a critical technology challenge for all types of biomass gasifiers. This USDA/DOE funded program (award number: DE-FG36-O8GO18085) aims to develop an advanced catalytic tar conversion system that can economically and efficiently convert tar into useful light gases (such as syngas) for downstream fuel synthesis or power generation. This program has been executed by GE Global Research in Irvine, CA, in collaboration with Professor Lanny Schmidt's group at the University of Minnesota (UoMn). Biomass gasification produces a raw syngas stream containing H2, CO, CO2, H2O, CH4 and other hydrocarbons, tars, char, and ash. Tars are defined as organic compounds that are condensable at room temperature and are assumed to be largely aromatic. Downstream units in biomass gasification such as gas engine, turbine or fuel synthesis reactors require stringent control in syngas quality, especially tar content to avoid plugging (gum) of downstream equipment. Tar- and ash-free syngas streams are a

Method and apparatus for coating thin foil with a boron coating

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lacy, Jeffrey L.

An apparatus and a process is disclosed for applying a boron coating to a thin foil. Preferably, the process is a continuous, in-line process for applying a coating to a thin foil comprising wrapping the foil around a rotating and translating mandrel, cleaning the foil with glow discharge in an etching chamber as the mandrel with the foil moves through the chamber, sputtering the foil with boron carbide in a sputtering chamber as the mandrel moves through the sputtering chamber, and unwinding the foil off the mandrel after it has been coated. The apparatus for applying a coating to amore » thin foil comprises an elongated mandrel. Foil preferably passes from a reel to the mandrel by passing through a seal near the initial portion of an etching chamber. The mandrel has a translation drive system for moving the mandrel forward and a rotational drive system for rotating mandrel as it moves forward. The etching chamber utilizes glow discharge on a surface of the foil as the mandrel moves through said etching chamber. A sputtering chamber, downstream of the etching chamber, applies a thin layer comprising boron onto the surface of the foil as said mandrel moves through said sputtering chamber. Preferably, the coated foil passes from the mandrel to a second reel by passing through a seal near the terminal portion of the sputtering chamber.« less

Banded TARs in Iapygia

NASA Image and Video Library

2014-09-10

The tropics of Mars are commonly littered with small bright ripples that were somehow shaped by the wind. NASA Mars Reconnaissance Orbiter might provide a valuable clue to the formation of transverse aeolian ridges TARs elsewhere on Mars.

Effect of CrO3 Sealing Time on Anodized A12024-T3

NASA Astrophysics Data System (ADS)

Korda, Akhmad A.; Hidayat, R. Z.

2016-08-01

The effect of CrO3 sealing time on anodized aluminum alloy has been investigated. A1 2024-T3 were used as substrate. Anodizing was carried out using chromic acid. CrO3 sealing was conducted in CrO3 solution for 30, 60, 90, 120 and 150 minutes. As comparison, other specimens were also prepared as anodized and boiled water sealing. Thickness of the coating was observed by optical microscope. Anodized and sealing layer was analyzed by X- ray diffraction. The hardness of as anodized, boiled water sealing and CrO3 sealing were compared. The highest hardness is achieved by CrO3 sealed specimen and followed by boiled water sealing and as anodized specimens. The longer the processes of CrO3 sealing the higher layer thickness and therefore the higher hardness of the oxide layer. The best resistance to electrolyte penetration is achieved by the CrO3 sealed specimen followed by boiled water sealed and as anodized specimens. The higher thickness of oxide layer, the higher the resistance against electrolyte penetration.

29 CFR 1910.1002 - Coal tar pitch volatiles; interpretation of term.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 29 Labor 6 2013-07-01 2013-07-01 false Coal tar pitch volatiles; interpretation of term. 1910.1002... Hazardous Substances § 1910.1002 Coal tar pitch volatiles; interpretation of term. As used in § 1910.1000 (Table Z-1), coal tar pitch volatiles include the fused polycyclic hydrocarbons which volatilize from the...

29 CFR 1910.1002 - Coal tar pitch volatiles; interpretation of term.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 6 2010-07-01 2010-07-01 false Coal tar pitch volatiles; interpretation of term. 1910.1002... Hazardous Substances § 1910.1002 Coal tar pitch volatiles; interpretation of term. As used in § 1910.1000 (Table Z-1), coal tar pitch volatiles include the fused polycyclic hydrocarbons which volatilize from the...

29 CFR 1910.1002 - Coal tar pitch volatiles; interpretation of term.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 6 2011-07-01 2011-07-01 false Coal tar pitch volatiles; interpretation of term. 1910.1002... Hazardous Substances § 1910.1002 Coal tar pitch volatiles; interpretation of term. As used in § 1910.1000 (Table Z-1), coal tar pitch volatiles include the fused polycyclic hydrocarbons which volatilize from the...

29 CFR 1910.1002 - Coal tar pitch volatiles; interpretation of term.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 29 Labor 6 2012-07-01 2012-07-01 false Coal tar pitch volatiles; interpretation of term. 1910.1002... Hazardous Substances § 1910.1002 Coal tar pitch volatiles; interpretation of term. As used in § 1910.1000 (Table Z-1), coal tar pitch volatiles include the fused polycyclic hydrocarbons which volatilize from the...

29 CFR 1910.1002 - Coal tar pitch volatiles; interpretation of term.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 6 2014-07-01 2013-07-01 true Coal tar pitch volatiles; interpretation of term. 1910.1002... Hazardous Substances § 1910.1002 Coal tar pitch volatiles; interpretation of term. As used in § 1910.1000 (Table Z-1), coal tar pitch volatiles include the fused polycyclic hydrocarbons which volatilize from the...

Coal tar-containing asphalt - resource or hazardous waste?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andersson-Skold, Y.; Andersson, K.; Lind, B.

2007-09-30

Coal tar was used in Sweden for the production of asphalt and for the drenching of stabilization gravel until 1973. The tar has high concentrations of polycyclic aromatic hydrocarbons (PAH), some of which may be strongly carcinogenic. Approximately 20 million tonnes of tar-containing asphalt is present in the public roads in Sweden. Used asphalt from rebuilding can be classified as hazardous waste according to the Swedish Waste Act. The cost of treating the material removed as hazardous waste can be very high due to the large amount that has to be treated, and the total environmental benefit is unclear. Themore » transport of used asphalt to landfill or combustion will affect other environmental targets. The present project, based on three case studies of road projects in Sweden, evaluates the consequences of four scenarios for handling the material: reuse, landfill, biological treatment, and incineration. The results show that reuse of the coal tar-containing materials in new road construction is the most favorable alternative in terms of cost, material use, land use, energy consumption, and air emissions.« less

Electrically Conductive and Protective Coating for Planar SOFC Stacks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choi, Jung-Pyung; Stevenson, Jeffry W.

Ferritic stainless steels are preferred interconnect materials for intermediate temperature SOFCs because of their resistance to oxidation, high formability and low cost. However, their protective oxide layer produces Cr-containing volatile species at SOFC operating temperatures and conditions, which can cause cathode poisoning. Electrically conducting spinel coatings have been developed to prevent cathode poisoning and to maintain an electrically conductive pathway through SOFC stacks. However, this coating is not compatible with the formation of stable, hermetic seals between the interconnect frame component and the ceramic cell. Thus, a new aluminizing process has been developed by PNNL to enable durable sealing, preventmore » Cr evaporation, and maintain electrical insulation between stack repeat units. Hence, two different types of coating need to have stable operation of SOFC stacks. This paper will focus on the electrically conductive coating process. Moreover, an advanced coating process, compatible with a non-electrically conductive coating will be« less

Assessment of Runoff Toxicity from Coated Surfaces

EPA Science Inventory

Presented in this paper are results from a field and laboratory study of the potential runoff toxicity from coated surfaces. The study results qualified and quantified the types and concentrations of pollutants in runoff from surfaces sealed with a variety of products. Coatings a...

Transformation-associated recombination (TAR) cloning for genomics studies and synthetic biology

PubMed Central

Kouprina, Natalay; Larionov, Vladimir

2016-01-01

Transformation-associated recombination (TAR) cloning represents a unique tool for isolation and manipulation of large DNA molecules. The technique exploits a high level of homologous recombination in the yeast Sacharomyces cerevisiae. So far, TAR cloning is the only method available to selectively recover chromosomal segments up to 300 kb in length from complex and simple genomes. In addition, TAR cloning allows the assembly and cloning of entire microbe genomes up to several Mb as well as engineering of large metabolic pathways. In this review, we summarize applications of TAR cloning for functional/structural genomics and synthetic biology. PMID:27116033

The potential use of tar sand bitumen as paving asphalt

DOE Office of Scientific and Technical Information (OSTI.GOV)

Petersen, J.C.

1988-01-01

In this paper several research reports describing the preparation of potential paving asphalts from tar sand bitumen are reviewed and the results of the studies compared. The tar sand asphalts described in the studies were prepared from 1) hot water-recovered bitumen from deposits near San Luis Obispo, California (Edna deposits), and deposits near Vernal and Sunnyside, Utah; and 2) bitumen recovered from the Northwest Asphalt Ridge deposits near Vernal, Utah, by both in situ steamflood and in situ combustion recovery processes. Important properties of the tar sand asphalts compare favorably with those of specification petroleum asphalts. Laboratory data suggest thatmore » some tar sand asphalts may have superior aging characteristics and produce more water-resistant paving mixtures than typical petroleum asphalts.« less

RETRACTED: Chemical densification of plasma sprayed yttria stabilized zirconia (YSZ) coatings for high temperature wear and corrosion resistance

NASA Astrophysics Data System (ADS)

Ye, Yaping; Fehr, Karl Thomas; Faulstich, Martin; Wolf, Gerhard

2012-12-01

Plasma-sprayed yttria stabilized zirconia (YSZ) ceramic coatings have been widely used as wear- and corrosion-resistant coatings in high temperature applications and an aggressive environment due to their high hardness, wear resistance, heat and chemical resistance, and low thermal conductivity. The highly porous structure of plasma-sprayed ceramic coatings and their poor adhesion to the substrate usually lead to the coating degradation and failure. In this study, a two-layer system consisting of atmospheric plasma-sprayed 8 wt.% yttria-stabilized zirconia (8YSZ) and Ni-based alloy coatings was post-treated by means of a novel chemical sealing process at moderate temperatures of 600-800 °C. Microstructure characteristics of the YSZ coatings were studied using an electron probe micro-analyzer (EPMA). Results revealed that the ceramic top coat was densified by the precipitated zirconia in the open pores. Therefore, the sealed YSZ coatings exhibit reduced porosity, higher hardness and a better adhesion onto the bond coat. The mechanisms for the sealing process were also proposed.

Coal tar induces AHR-dependent skin barrier repair in atopic dermatitis

PubMed Central

van den Bogaard, Ellen H.; Bergboer, Judith G.M.; Vonk-Bergers, Mieke; van Vlijmen-Willems, Ivonne M.J.J.; Hato, Stanleyson V.; van der Valk, Pieter G.M.; Schröder, Jens Michael; Joosten, Irma; Zeeuwen, Patrick L.J.M.; Schalkwijk, Joost

2013-01-01

Topical application of coal tar is one of the oldest therapies for atopic dermatitis (AD), a T helper 2 (Th2) lymphocyte–mediated skin disease associated with loss-of-function mutations in the skin barrier gene, filaggrin (FLG). Despite its longstanding clinical use and efficacy, the molecular mechanism of coal tar therapy is unknown. Using organotypic skin models with primary keratinocytes from AD patients and controls, we found that coal tar activated the aryl hydrocarbon receptor (AHR), resulting in induction of epidermal differentiation. AHR knockdown by siRNA completely abrogated this effect. Coal tar restored filaggrin expression in FLG-haploinsufficient keratinocytes to wild-type levels, and counteracted Th2 cytokine–mediated downregulation of skin barrier proteins. In AD patients, coal tar completely restored expression of major skin barrier proteins, including filaggrin. Using organotypic skin models stimulated with Th2 cytokines IL-4 and IL-13, we found coal tar to diminish spongiosis, apoptosis, and CCL26 expression, all AD hallmarks. Coal tar interfered with Th2 cytokine signaling via dephosphorylation of STAT6, most likely due to AHR-regulated activation of the NRF2 antioxidative stress pathway. The therapeutic effect of AHR activation herein described opens a new avenue to reconsider AHR as a pharmacological target and could lead to the development of mechanism-based drugs for AD. PMID:23348739

Coal tar induces AHR-dependent skin barrier repair in atopic dermatitis.

PubMed

van den Bogaard, Ellen H; Bergboer, Judith G M; Vonk-Bergers, Mieke; van Vlijmen-Willems, Ivonne M J J; Hato, Stanleyson V; van der Valk, Pieter G M; Schröder, Jens Michael; Joosten, Irma; Zeeuwen, Patrick L J M; Schalkwijk, Joost

2013-02-01

Topical application of coal tar is one of the oldest therapies for atopic dermatitis (AD), a T helper 2 (Th2) lymphocyte-mediated skin disease associated with loss-of-function mutations in the skin barrier gene, filaggrin (FLG). Despite its longstanding clinical use and efficacy, the molecular mechanism of coal tar therapy is unknown. Using organotypic skin models with primary keratinocytes from AD patients and controls, we found that coal tar activated the aryl hydrocarbon receptor (AHR), resulting in induction of epidermal differentiation. AHR knockdown by siRNA completely abrogated this effect. Coal tar restored filaggrin expression in FLG-haploinsufficient keratinocytes to wild-type levels, and counteracted Th2 cytokine-mediated downregulation of skin barrier proteins. In AD patients, coal tar completely restored expression of major skin barrier proteins, including filaggrin. Using organotypic skin models stimulated with Th2 cytokines IL-4 and IL-13, we found coal tar to diminish spongiosis, apoptosis, and CCL26 expression, all AD hallmarks. Coal tar interfered with Th2 cytokine signaling via dephosphorylation of STAT6, most likely due to AHR-regulated activation of the NRF2 antioxidative stress pathway. The therapeutic effect of AHR activation herein described opens a new avenue to reconsider AHR as a pharmacological target and could lead to the development of mechanism-based drugs for AD.

Sampling of tar from sewage sludge gasification using solid phase adsorption.

PubMed

Ortiz González, Isabel; Pérez Pastor, Rosa Ma; Sánchez Hervás, José Ma

2012-06-01

Sewage sludge is a residue from wastewater treatment plants which is considered to be harmful to the environment and all living organisms. Gasification technology is a potential source of renewable energy that converts the sewage sludge into gases that can be used to generate energy or as raw material in chemical synthesis processes. But tar produced during gasification is one of the problems for the implementation of the gasification technology. Tar can condense on pipes and filters and may cause blockage and corrosion in the engines and turbines. Consequently, to minimize tar content in syngas, the ability to quantify tar levels in process streams is essential. The aim of this work was to develop an accurate tar sampling and analysis methodology using solid phase adsorption (SPA) in order to apply it to tar sampling from sewage sludge gasification gases. Four types of commercial SPA cartridges have been tested to determine the most suitable one for the sampling of individual tar compounds in such streams. Afterwards, the capacity, breakthrough volume and sample stability of the Supelclean™ ENVI-Carb/NH(2), which is identified as the most suitable, have been determined. Basically, no significant influences from water, H(2)S or NH(3) were detected. The cartridge was used in sampling real samples, and comparable results were obtained with the present and traditional methods.

PRDA-2 and 3 Brush Seal Development Programs at EG and G

NASA Technical Reports Server (NTRS)

Loewenthal, Robert G.

1996-01-01

EG&G Mechanical Components Technology Group R&D completed a Brush Seal Development Program under PRDA-2 in late 1992. We started the Advanced Brush Seal Development program, under PRDA-3, in 1993 and will complete it in 1996. Both programs have been funded by the United States Air Force. In the first program, we made significant gains in the area of tribopairs (bristle materials vs. shaft coatings) and the 'Low Hysteresis' design for brush seals. These were reported in two AIAA Propulsion Conference papers, and the 'Low Hysteresis' design has been patented. Seals were delivered for test in an Air Force demonstrator at Allison. In PRDA-3, goals are to increase the pressure sealing capability, and the surface speeds and temperatures at which brush seals can be used. We have conducted part of the design and testing and have tested brush seals successfully at more severe conditions than in the previous program. We are continuing with the program, and will complete it in time to furnish brush seals for an Air Force Demonstrator test in 1997.

Probing interaction of a fluorescent ligand with HIV TAR RNA

NASA Astrophysics Data System (ADS)

Qi, Liang; Zhang, Jing; He, Tian; Huo, Yuan; Zhang, Zhi-Qi

2017-02-01

Trans-activator of Transcription (Tat) antagonists could block the interaction between Tat protein and its target, trans-activation responsive region (TAR) RNA, to inhibit Tat function and prevent human immunodeficiency virus type 1 (HIV-1) replication. For the first time, a small fluorescence ligand, ICR 191, was found to interact with TAR RNA at the Tat binding site and compete with Tat. It was also observed that the fluorescence of ICR 191 could be quenched when binding to TAR RNA and recovered when discharged via competition with Tat peptide or a well-known Tat inhibitor, neomycin B. The binding parameters of ICR 191 to TAR RNA were determined through theoretical calculations. Mass spectrometry, circular dichroism and molecular docking were used to further confirm the interaction of ICR 191 with TAR RNA. Inspired by these discoveries, a primary fluorescence model for the discovery of Tat antagonists was built using ICR 191 as a fluorescence indicator and the feasibility of this model was evaluated. This ligand-RNA interaction could provide a new strategy for research aimed at discovering Tat antagonists.

Thermocatalytic treatment of biomass tar model compounds via radio frequency.

PubMed

Anis, Samsudin; Zainal, Z A; Bakar, M Z A

2013-05-01

A new effective RF tar thermocatalytic treatment process with low energy intensive has been proposed to remove tar from biomass gasification. Toluene and naphthalene as biomass tar model compounds were removed via both thermal and catalytic treatment over a wide temperature range from 850 °C to 1200 °C and 450 °C to 900 °C, respectively at residence time of 0-0.7 s. Thermal characteristics of the new technique are also described in this paper. This study clearly clarified that toluene was much easier to be removed than naphthalene. Soot was found as the final product of thermal treatment of the tar model and completely removed during catalytic treatment. Radical reactions generated by RF non-thermal effect improve the tar removal. The study showed that Y-zeolite has better catalytic activity compared to dolomite on toluene and naphthalene removal due to its acidic nature and large surface area, even at lower reaction temperature of about 550 °C. Copyright © 2013 Elsevier Ltd. All rights reserved.

Assessment of tar pollution on the United Arab emirates beaches

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abu-Hilal, A.H.; Khordagui, H.K.

1993-01-01

In light of the inadequate information concerning stranded tar on the southwest beaches of the Arabian Gulf and the Gulf of Oman, particularly following the massive oil releases during the Gulf War, the present investigation was designed to provide reference-integrated information on the nature, location, and levels of stranded tar balls on the beaches of the United Arab Emirates (UAE). The recorded levels appeared to be higher than expected or previously reported. The tar distribution pattern, in addition to the degree of weathering, indicates that the massive oil release during the Gulf War did not reach the UAE shorelines. Themore » highest reported levels of stranded tar ever recorded in the Arabian Gulf at Jabal Dhannah apparently originated from oil spills and tankers' ballast water at the main oil terminal at the Al-Ruwaiss oil refinery some 10 km to the east. The surprising, relatively high levels of stranded tar on the beaches of the Gulf of Oman were solely attributed to the heavy navigation traffic close to the shorelines. 19 refs., 2 figs., 3 tabs.« less

Seals and Sealing Techniques

NASA Technical Reports Server (NTRS)

1972-01-01

Developments by the aerospace industry in seals and sealing techniques are announced for possible use in other areas. The announcements presented are grouped as: sealing techniques for cryogenic fluids, high pressure applications, and modification for improved performance.

Solder glass sealing technology for use in packaging of fiber optic sensors

NASA Astrophysics Data System (ADS)

Kreutzmann, Gerd

1990-08-01

The solder glass sealing technology is an alternative to the direct sealing method of the socalled hboptocansu. Using solder glass for the junction of glass and the metal can the temperature at about 500 °C does not destroy the optical quality of the precision glass components. The glass can also be coated with an antireflective layer and even the sealing of filterglass is possible. In cases where coupling losses can't be tolerated, the fiber has to be fed directly through the wall into the housing. Fiber feedthroughs, using solder glass for the sealing of the fiber into a metal tube, are commonly metal soldered or welded into the wall and the fiber surface is directly leading to the semiconductor.

Thermodynamic analysis of tar reforming through auto-thermal reforming process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nurhadi, N., E-mail: nurhadi@tekmira.esdm.go.id; Diniyati, Dahlia; Efendi, M. Ade Andriansyah

2015-12-29

Fixed bed gasification is a simple and suitable technology for small scale power generation. One of the disadvantages of this technology is producing tar. So far, tar is not utilized yet and being waste that should be treated into a more useful product. This paper presents a thermodynamic analysis of tar conversion into gas producer through non-catalytic auto-thermal reforming technology. Tar was converted into components, C, H, O, N and S, and then reacted with oxidant such as mixture of air or pure oxygen. Thus, this reaction occurred auto-thermally and reached chemical equilibrium. The sensitivity analysis resulted that the mostmore » promising process performance occurred at flow rate of air was reached 43% of stoichiometry while temperature of process is 1100°C, the addition of pure oxygen is 40% and preheating of oxidant flow is 250°C. The yield of the most promising process performance between 11.15-11.17 kmol/h and cold gas efficiency was between 73.8-73.9%.The results of this study indicated that thermodynamically the conversion of tar into producer gas through non-catalytic auto-thermal reformingis more promising.« less

Groundwater contamination by organic bases derived from coal-tar wastes

USGS Publications Warehouse

Pereira, W.E.; Rostad, C.E.; Garbarino, J.R.; Hult, M.F.

1983-01-01

A fluid sample from a shallow aquifer contaminated by coal-tar wastes was analyzed for organic bases. The sample consisted of a mixture of aqueous and oily-tar phases. The phases were separated by centrifugation and filtration. Organic bases were isolated from each phase by pH adjustment and solvent extraction. Organic bases in the oily-tar phase were further purified by neutral-alumina, micro-column adsorption chromatography. Separation and identification of the organic bases in each phase were achieved by using capillary gas chromatography-mass spectrometry-computer (GC-MS-COM) and probe distillation-high resolution mass spectrometry (PD-HRMS) techniques. Organic bases present in the aqueous phase included primary aromatic amines (such as aniline, alkylated anilines, and naphthylamines) as well as azaarenes (such as alkylated pyridines, quinolines, acridine, and benzoquinolines). The oily-tar phase contained acridine, benzacridines, dibenzacridines, and numerous other azaarenes, the elemental compositions of which were determined by PD-HRMS. Azaarenes in the oily-tar phase, varying in size from 6 to 12 rings, are reported for the first time. The origin and environmental significance of these compounds are discussed. ?? 1983.

EVALUATION OF TOXICS IN RUNOFF FROM COATED SURFACES

EPA Science Inventory

Presented in this paper are results from a field and laboratory study of the potential runoff toxicity from coated surfaces. The study results qualified and quantified the types and concentrations of pollutants in runoff from surfaces sealed with a variety of products. Coatings a...

Deciphering structure-activity relationships in a series of Tat/TAR inhibitors.

PubMed

Pascale, Lise; González, Alejandro López; Di Giorgio, Audrey; Gaysinski, Marc; Teixido Closa, Jordi; Tejedor, Roger Estrada; Azoulay, Stéphane; Patino, Nadia

2016-11-01

A series of pentameric "Polyamide Amino Acids" (PAAs) compounds derived from the same trimeric precursor have been synthesized and investigated as HIV TAR RNA ligands, in the absence and in the presence of a Tat fragment. All PAAs bind TAR with similar sub-micromolar affinities but their ability to compete efficiently with the Tat fragment strongly differs, IC50 ranging from 35 nM to >2 μM. While NMR and CD studies reveal that all PAA interact with TAR at the same site and induce globally the same RNA conformational change upon binding, a comparative thermodynamic study of PAA/TAR equilibria highlights distinct TAR binding modes for Tat competitor and non-competitor PAAs. This led us to suggest two distinct interaction modes that have been further validated by molecular modeling studies. While the binding of Tat competitor PAAs induces a contraction at the TAR bulge region, the binding of non-competitor ones widens it. This could account for the distinct PAA ability to compete with Tat fragment. Our work illustrates how comparative thermodynamic studies of a series of RNA ligands of same chemical family are of value for understanding their binding modes and for rationalizing structure-activity relationships.

Friction and wear of several compressor gas-path seal movements

NASA Technical Reports Server (NTRS)

Bill, R. C.; Wisander, D. W.

1978-01-01

Rub interaction experiments were conducted on a series of sintered and plasma sprayed compressor gas path seal materials in contact with Ti-6Al-4V blade tip and knife edge rotors. The most rub tolerant materials investigated were sintered Nichrome and plasma sprayed nickel 25 percent graphite. The effectiveness of providing a compliant substrate for dense seal material coatings was also demonstrated. In general, it was observed that rotor wear and high frictional energy generation rates accompanied smearing or surface densification of the materials investigated. The onset of smearing was sensitive to rub interaction parameters and seal geometry. Two complementary models were proposed to account for the smearing trends. One is based on thermal effects, the other on particulate escape effects. They were shown to be consistent with the experimental evidence at hand, and together they predict that smearing, with the onset of high energy rub conditions, is favored when incursion rates (radial motion) are low, incursion depths are high, the seal geometry is of a knife-edge character, and the seal particle size is small.

Effect of water addition in a microwave assisted thermal cracking of biomass tar gasification

NASA Astrophysics Data System (ADS)

Warsita, A.; Surya, I.

2018-02-01

Producer gas from biomass gasification is plagued by the presence of tar which causes pipe blockages. Thermal and catalytic treatments in a microwave reactor have been shown to be effective methods for removing tar from producer gas. A question arises as to the possibility of enhancing the removal mechanism by adding water into the reactor. Thermal treatment with a various amount of water was added at temperatures in the range of 800-1200°C. The tar removal efficiency obtained 96.32% at the optimum temperature of 1200°C at the water to tar ratio (W/T) of 0.3. This study shows that the removal of tar by microwave irradiation with water addition is a significant and effective method in tar cracking.

The TAR effect: when the ones who dislike become the ones who are disliked.

PubMed

Gawronski, Bertram; Walther, Eva

2008-09-01

Four studies tested whether a source's evaluations of other individuals can recursively transfer to the source, such that people who like others acquire a positive valence, whereas people who dislike others acquire a negative valence (Transfer of Attitudes Recursively; TAR). Experiment 1 provides first evidence for TAR effects, showing recursive transfers of evaluations regardless of whether participants did or did not have prior knowledge about the (dis)liking source. Experiment 2 shows that previously but not subsequently acquired knowledge about targets that were (dis)liked by a source overrode TAR effects in a manner consistent with cognitive balance. Finally, Experiments 3 and 4 demonstrate that TAR effects are mediated by higher order propositional inferences (in contrast to lower order associative processes), in that TAR effects on implicit attitude measures were fully mediated by TAR effects on explicit attitude measures. Commonalities and differences between the TAR effect and previously established phenomena are discussed.

Coal-tar based pavement sealant toxicity to freshwater macroinvertebrates.

PubMed

Bryer, Pamela J; Scoggins, Mateo; McClintock, Nancy L

2010-05-01

Non-point-source pollution is a major source of ecological impairment in urban stream systems. Recent work suggests that coal-tar pavement sealants, used extensively to protect parking areas, may be contributing a large portion of the polycyclic aromatic hydrocarbon (PAH) loading seen in urban stream sediments. The hypothesis that dried coal-tar pavement sealant flake could alter the macroinvertebrate communities native to streams in Austin, TX was tested using a controlled outdoor laboratory type approach. The treatment groups were: control, low, medium, and high with total PAH concentrations (TPAH = sum of 16 EPA priority pollutant PAHs) of 0.1, 7.5, 18.4, & 300 mg/kg respectively. The low, medium, and high treatments were created via the addition of dried coal-tar pavement sealant to a sterile soil. At the start of the 24-day exposure, sediment from a minimally impacted local reference site containing a community of live sediment-dwelling benthic macroinvertebrates was added to each replicate. An exposure-dependent response was found for several stream health measures and for several individual taxa. There were community differences in abundance (P = 0.0004) and richness (P < 0.0001) between treatments in addition to specific taxa responses, displaying a clear negative relationship with the amount of coal-tar sealant flake. These results support the hypothesis that coal-tar pavement sealants contain bioavailable PAHs that may harm aquatic environments. Copyright 2009 Elsevier Ltd. All rights reserved.

Ground-water contamination by organic bases derived from coal-tar wastes

USGS Publications Warehouse

Pereira, Wilfred E.; Rostad, Colleen E.; Garbarino, John R.; Hult, Marc F.

1983-01-01

A fluid sample from a shallow aquifer contaminated by coal-tar wastes was analyzed for organic bases. The sample consisted of a mixture of aqueous and oily-tar phases. The phases were separated by centrifugation and filtration. Organic bases were isolated from each phase by pH adjustment and solvent extraction. Organic bases in the oily-tar phase were further purified by neutral-alumina, micro-column adsorption chromatography. Separation and identification of the organic bases in each phase were achieved by using capillary gas chromatography-mass spectrometry-computer (GC-MS-COM) and probe distillation-high resolution mass spectrometry (PD-HRMS) techniques. Organic bases present in the aqueous phase included primary aromatic amines (such as aniline, alkylated anilines, and naphthylamines) as well as azaarenes (such as alkylated pyridines, quinolines, acridine, and benzoquinolines). The oily-tar phase contained acridine, benzacridines, dibenzacridines, and numerous other azaarenes, the elemental compositions of which were determined by PD-HRMS. Azaarenes in the oily-tar phase, varying in size from 6 to 12 rings, are reported for the first time. The origin and environmental significance of these compounds are discussed.

Role of TAR RNA splicing in translational regulation of simian immunodeficiency virus from rhesus macaques.

PubMed Central

Viglianti, G A; Rubinstein, E P; Graves, K L

1992-01-01

The untranslated leader sequences of rhesus macaque simian immunodeficiency virus mRNAs form a stable secondary structure, TAR. This structure can be modified by RNA splicing. In this study, the role of TAR splicing in virus replication was investigated. The proportion of viral RNAs containing a spliced TAR structure is high early after infection and decreases at later times. Moreover, proviruses containing mutations which prevent TAR splicing are significantly delayed in replication. These mutant viruses require approximately 20 days to achieve half-maximal virus production, in contrast to wild-type viruses, which require approximately 8 days. We attribute this delay to the inefficient translation of unspliced-TAR-containing mRNAs. The molecular basis for this translational effect was examined in in vitro assays. We found that spliced-TAR-containing mRNAs were translated up to 8.5 times more efficiently than were similar mRNAs containing an unspliced TAR leader. Furthermore, these spliced-TAR-containing mRNAs were more efficiently associated with ribosomes. We postulate that the level of TAR splicing provides a balance for the optimal expression of both viral proteins and genomic RNA and therefore ultimately controls the production of infectious virions. Images PMID:1629957

Tests Of Polyurethane And Dichromate Coats On Aluminum

NASA Technical Reports Server (NTRS)

Danford, M. D.

1992-01-01

Report describes experiments to determine relative effectiveness of new polyurethane and more-conventional dichromate coat in helping to retard corrosion of anodized 6061-T6 aluminum. Concludes by suggesting greater protection against corrosion achieved by combining polyurethane-sealing method with hard-anodizing method and by increasing thickness of coat.

Selected constituents in the smoke of domestic low tar cigarettes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Griest, W. H.; Quincy, R. B.; Guerin, M. R.

Thirty-two brands of domestic commercial low tar and nicotine cigarettes were analyzed for their production of tar, nicotine, nitrogen oxides (as nitric oxide), hydrogen cyanide, acrolein, carbon monoxide and carbon dioxide under standard analytical smoking conditions. Results are compared with published data for certain brands.

The contribution of low tar cigarettes to environmental tobacco smoke

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chortyk, O.T.; Schlotzhauer, W.S.

A series of low tar cigarettes (LTC) were smoked and the quantities of condensable mainstream (inhaled) and sidestream (between puffs) smoke compounds were determined and compared to those produced by a high tar, nonfilter cigarette. It was found that the LTC produced large quantities of sidestream smoke condensates, about equal to the high tar cigarette, and contained very high levels of toxic or cocarcinogenic phenols. On an equal weight basis, the LTC emitted more of these hazardous compounds into sidestream and environmental tobacco smoke. Higher smoke yields of a flavor additive and a sugar degradation product indicated addition of suchmore » compounds during the manufacture of LTC. It was concluded that, compared to a high tar cigarette, smoking LTC may be better for the smoker, but not for the nearby nonsmoker. Information should be developed to allow smokers to choose LTC that produce lower levels of hazardous compounds in their environmentally emitted sidestream smoke.« less

Complete prevention of blood loss with self-sealing haemostatic needles

NASA Astrophysics Data System (ADS)

Shin, Mikyung; Park, Sung-Gurl; Oh, Byung-Chang; Kim, Keumyeon; Jo, Seongyeon; Lee, Moon Sue; Oh, Seok Song; Hong, Seon-Hui; Shin, Eui-Cheol; Kim, Ki-Suk; Kang, Sun-Woong; Lee, Haeshin

2017-01-01

Bleeding is largely unavoidable following syringe needle puncture of biological tissues and, while inconvenient, this typically causes little or no harm in healthy individuals. However, there are certain circumstances where syringe injections can have more significant side effects, such as uncontrolled bleeding in those with haemophilia, coagulopathy, or the transmission of infectious diseases through contaminated blood. Herein, we present a haemostatic hypodermic needle able to prevent bleeding following tissue puncture. The surface of the needle is coated with partially crosslinked catechol-functionalized chitosan that undergoes a solid-to-gel phase transition in situ to seal punctured tissues. Testing the capabilities of these haemostatic needles, we report complete prevention of blood loss following intravenous and intramuscular injections in animal models, and 100% survival in haemophiliac mice following syringe puncture of the jugular vein. Such self-sealing haemostatic needles and adhesive coatings may therefore help to prevent complications associated with bleeding in more clinical settings.

Creating fluid injectivity in tar sands formations

DOEpatents

Stegemeier, George Leo; Beer, Gary Lee; Zhang, Etuan

2012-06-05

Methods for treating a tar sands formation are described herein. Methods for treating a tar sands may include heating a portion of a hydrocarbon layer in the formation from one or more heaters located in the portion. The heat may be controlled to increase the permeability of at least part of the portion to create an injection zone in the portion with an average permeability sufficient to allow injection of a fluid through the injection zone. A drive fluid and/or an oxidizing fluid may be provided into the injection zone. At least some hydrocarbons including mobilized hydrocarbons are produced from the portion.

Creating fluid injectivity in tar sands formations

DOEpatents

Stegemeier, George Leo; Beer, Gary Lee; Zhang, Etuan

2010-06-08

Methods for treating a tar sands formation are described herein. Methods for treating a tar sands may include heating a portion of a hydrocarbon layer in the formation from one or more heaters located in the portion. The heat may be controlled to increase the permeability of at least part of the portion to create an injection zone in the portion with an average permeability sufficient to allow injection of a fluid through the injection zone. A drive fluid and/or an oxidizing fluid may be provided into the injection zone. At least some hydrocarbons are produced from the portion.

High Temperature Brush Seal Tuft Testing of Selected Nickel-Chrome and Cobalt-Chrome Superalloys

NASA Technical Reports Server (NTRS)

Fellenstein, James A.; DellaCorte, Christopher; Moore, Kenneth D.; Boyes, Esther

1997-01-01

The tribology of brush seals is of considerable interest to turbine engine designers because bristle wear continues to limit long term seal performance and life. To provide better materials characterization and foster the development of improved seals, NASA Lewis has developed a brush seal tuft tester. In this test, a 'paintbrush' sample tuft is loaded under constant contact pressure against the outside diameter of a rotating journal. With this configuration, load and friction are directly measured and accurate wear measurements are possible. Previously reported research using this facility showed excellent data repeatability and wear morphology similar to published seal data and dynamic rig tests. This paper is an update of the ongoing research into the tribology of brush seals. The effects of wire materials processing on seal wear and the tribological results for three journal coatings are discussed. Included in the materials processing were two nickel-chrome superalloys each processed to two different yield strengths. The results suggest that seal wear is dependent more on material composition than processing conditions.

Continued development of abradable gas path seals. [for gas turbine engines

NASA Technical Reports Server (NTRS)

Shiembob, L. T.

1975-01-01

Major program objectives were the continued development of NiCrAlY feltmetal and honeycomb systems for knife edge seal applications in the 1144 to 1366 K temperature range, and to initiate abradable seal material evaluation for blade tip seal applications in the 1366 to 1589 K temperature range. Larger fiber size, higher density feltmetal showed greatly improved erosion resistance with a slight reduction in abradability compared to the baseline feltmetal. Pack aluminide coating of the honeycomb extended the oxidation resistance and slightly improved the abradability of this material. Evaluation through selected abradability, erosion and oxidation testing, and pertinent metallography led to selection of a plasma sprayed yttria stabilized zirconia (ZrO2)/CoCrAlY layered system as the system with the most potential to meet the 1589 K requirement for blade tip seals. This system demonstrated structural integrity, erosion resistance, and some degree of abradability.

21 CFR 740.18 - Coal tar hair dyes posing a risk of cancer.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 7 2012-04-01 2012-04-01 false Coal tar hair dyes posing a risk of cancer. 740.18... (CONTINUED) COSMETICS COSMETIC PRODUCT WARNING STATEMENTS Warning Statements § 740.18 Coal tar hair dyes... coal tar hair dye containing any ingredient listed in paragraph (b) of this section shall bear, in...

Method and device for producing and delivering an aerosol for remote sealing and coating

DOEpatents

Modera, M.P.; Carrie, F.R.

1996-06-04

The invention is a method and device for sealing leaks remotely by means of injecting a previously prepared aerosol into the enclosure being sealed. Specifically the invention is a method and device for preparing, transporting, and depositing and solid phase aerosol to the interior surface of the enclosure. 1 fig.

Contracting/expanding self-sealing cryogenic tube seals

NASA Technical Reports Server (NTRS)

Jia, Lin X. (Inventor)

1997-01-01

Contracting/expanding self-sealing cryogenic tube seals are disclosed which use the different properties of thermal contraction and expansion of selected dissimilar materials in accord with certain design criteria to yield self-tightening seals via sloped-surface sealing. The seals of the subject invention are reusable, simple to assemble, adaptable to a wide variety of cryogenic applications.

Contracting/expanding self-sealing cryogenic tube seals

NASA Technical Reports Server (NTRS)

Jia, Lin X. (Inventor)

1997-01-01

Contracting/expanding self-sealing cryogenic tube seals are disclosed which use the different properties of thermal contraction and expansion of selected dissimilar materials in accord with certain design criteria to yield self-tightening seals via sloped-surface sealing. The seals of the subject invention are reusable, simple to assemble, and adaptable to a wide variety of cryogenic applications.

Understanding the stability of pyrolysis tars from biomass in a view point of free radicals.

PubMed

He, Wenjing; Liu, Qingya; Shi, Lei; Liu, Zhenyu; Ci, Donghui; Lievens, Caroline; Guo, Xiaofen; Liu, Muxin

2014-03-01

Fast pyrolysis of biomass has attracted increasing attention worldwide to produce bio-tars that can be upgraded into liquid fuels and chemicals. However, the bio-tars are usually poor in quality and stability and are difficult to be upgraded. To better understand the nature of the bio-tars, this work reveals radical concentration of tars derived from pyrolysis of two kinds of biomass. The tars were obtained by condensing the pyrolysis volatiles in 3s. It shows that the tars contain large amounts of radicals, at a level of 10(16)spins/g, and are able to generate more radicals at temperatures of 573K or higher, reaching a level of 10(19)spins/g at 673K in less than 30min. The radical generation in the tar samples is attributed to the formation of THF insoluble matters (coke), which also contain radicals. The radical concentrations of the aqueous liquids obtained in pyrolysis are also studied. Copyright © 2014 Elsevier Ltd. All rights reserved.

Improvement on the Fatigue Performance of 2024-T4 Alloy by Synergistic Coating Technology

PubMed Central

Wang, Xi-Shu; Guo, Xing-Wu; Li, Xu-Dong; Ge, Dong-Yun

2014-01-01

In this paper, rotating bending fatigue tests of 2024-T4 Al alloy with different oxide coatings were carried out. Compared to the uncoated and previously reported oxide coatings of aluminum alloys, the fatigue strength is able to be enhanced by using a novel oxide coating with sealing pore technology. These results indicate that the better the coating surface quality is, the more excellent the fatigue performance under rotating bending fatigue loading is. The improvement on the fatigue performance is mainly because the fatigue crack initiation and the early stage of fatigue crack growth at the coating layer can be delayed after PEO coating with pore sealing. Therefore, it is a so-called synergistic coating technology for various uses, including welding thermal cracks and filling micro-pores. The effects of different oxide coatings on surface hardness, compressive residual stress, morphology and fatigue fracture morphology are discussed. A critical compressive residual stress of about 95–100 MPa is proposed. PMID:28788634

Catalytic Tar Reduction for Assistance in Thermal Conversion of Space Waste for Energy Production

NASA Technical Reports Server (NTRS)

Caraccio, Anne Joan; Devor, Robert William; Hintze, Paul E.; Muscatello, Anthony C.; Nur, Mononita

2014-01-01

The Trash to Gas (TtG) project investigates technologies for converting waste generated during spaceflight into various resources. One of these technologies was gasification, which employed a downdraft reactor designed and manufactured at NASA's Kennedy Space Center (KSC) for the conversion of simulated space trash to carbon dioxide. The carbon dioxide would then be converted to methane for propulsion and water for life support systems. A minor byproduct of gasification includes large hydrocarbons, also known as tars. Tars are unwanted byproducts that add contamination to the product stream, clog the reactor and cause complications in analysis instrumentation. The objective of this research was to perform reduction studies of a mock tar using select catalysts and choose the most effective for primary treatment within the KSC downdraft gasification reactor. Because the KSC reactor is operated at temperatures below typical gasification reactors, this study evaluates catalyst performance below recommended catalytic operating temperatures. The tar reduction experimentation was observed by passing a model tar vapor stream over the catalysts at similar conditions to that of the KSC reactor. Reduction in tar was determined using gas chromatography. Tar reduction efficiency and catalyst performances were evaluated at different temperatures.

Metal catalysts for steam reforming of tar derived from the gasification of lignocellulosic biomass.

PubMed

Li, Dalin; Tamura, Masazumi; Nakagawa, Yoshinao; Tomishige, Keiichi

2015-02-01

Biomass gasification is one of the most important technologies for the conversion of biomass to electricity, fuels, and chemicals. The main obstacle preventing the commercial application of this technology is the presence of tar in the product gas. Catalytic reforming of tar appears a promising approach to remove tar and supported metal catalysts are among the most effective catalysts. Nevertheless, improvement of catalytic performances including activity, stability, resistance to coke deposition and aggregation of metal particles, as well as catalyst regenerability is greatly needed. This review focuses on the design and catalysis of supported metal catalysts for the removal of tar in the gasification of biomass. The recent development of metal catalysts including Rh, Ni, Co, and their alloys for steam reforming of biomass tar and tar model compounds is introduced. The role of metal species, support materials, promoters, and their interfaces is described. Copyright © 2014 Elsevier Ltd. All rights reserved.

Wet scrubbing of biomass producer gas tars using vegetable oil

NASA Astrophysics Data System (ADS)

Bhoi, Prakashbhai Ramabhai

The overall aims of this research study were to generate novel design data and to develop an equilibrium stage-based thermodynamic model of a vegetable oil based wet scrubbing system for the removal of model tar compounds (benzene, toluene and ethylbenzene) found in biomass producer gas. The specific objectives were to design, fabricate and evaluate a vegetable oil based wet scrubbing system and to optimize the design and operating variables; i.e., packed bed height, vegetable oil type, solvent temperature, and solvent flow rate. The experimental wet packed bed scrubbing system includes a liquid distributor specifically designed to distribute a high viscous vegetable oil uniformly and a mixing section, which was designed to generate a desired concentration of tar compounds in a simulated air stream. A method and calibration protocol of gas chromatography/mass spectroscopy was developed to quantify tar compounds. Experimental data were analyzed statistically using analysis of variance (ANOVA) procedure. Statistical analysis showed that both soybean and canola oils are potential solvents, providing comparable removal efficiency of tar compounds. The experimental height equivalent to a theoretical plate (HETP) was determined as 0.11 m for vegetable oil based scrubbing system. Packed bed height and solvent temperature had highly significant effect (p0.05) effect on the removal of model tar compounds. The packing specific constants, Ch and CP,0, for the Billet and Schultes pressure drop correlation were determined as 2.52 and 2.93, respectively. The equilibrium stage based thermodynamic model predicted the removal efficiency of model tar compounds in the range of 1-6%, 1-4% and 1-2% of experimental data for benzene, toluene and ethylbenzene, respectively, for the solvent temperature of 30° C. The NRTL-PR property model and UNIFAC for estimating binary interaction parameters are recommended for modeling absorption of tar compounds in vegetable oils. Bench scale

Acid Tar Lagoons: Management and Recovery

NASA Astrophysics Data System (ADS)

Bohers, Anna; Hroncová, Emília; Ladomerský, Juraj

2017-04-01

This contribution presents the issue with possibility of definitive removal of dangerous environmental burden in Slovakia - serious historical problem of two acid tar lagoons. In relation to their removal, no technology has been found so far - technologically and economically suitable, what caused problems with its management. Locality Predajná is well known in Slovakia by its character of contrasts: it is situated in the picturesque landscape of National Park buffer zone of Nízke Tatry, on the other site it is contaminated by 229 211m3 of acid tar with its characteristics of toxicity, carcinogenicity, teratogenicity, mutagenicity and toxicity especially for animals and plants. Acid tar in two landfills with depth of 1m in case of the first lagoon and 9,5m in case of the second lagoon is a waste product derived from operation of Petrochema Dubová - refinery and petrochemical plant whose activity was to process the crude oil through processes of sulfonation and adsorption technology for producing lubricating and special oils, synthetic detergents and special white oils for cosmetic and medical purposes. A part of acid tar was incinerated in two incineration plats. Concentration of SO2 in combustion gases was too high and it was not possible to decrease it under the value of 2000 mg.mn-3 [LADOMERSKÝ, J. - SAMEŠOVÁ, D.: Reduction in sulfur dioxide emissions waste gases of incineration plant. Acta facultatis ecologiae. 1999, p. 217-223]. That is why it was necessary to put them out of operation. Later, because of public opposition it was not possible to build a new incineration plat corresponding to the state of the art. Even though actual Slovak and European legislative for protection of environment against such impacts, neither of tried methods - bio or non-biologic treatment methods - was proved as suitable for processing or for recovery in the reason of different factors admission: i.e. strong aggressivity, difficulty with handling because of its sludgy and

Porous Carbon Nanofibers from Electrospun Biomass Tar/Polyacrylonitrile/Silver Hybrids as Antimicrobial Materials.

PubMed

Song, Kunlin; Wu, Qinglin; Zhang, Zhen; Ren, Suxia; Lei, Tingzhou; Negulescu, Ioan I; Zhang, Quanguo

2015-07-15

A novel route to fabricate low-cost porous carbon nanofibers (CNFs) using biomass tar, polyacrylonitrile (PAN), and silver nanoparticles has been demonstrated through electrospinning and subsequent stabilization and carbonization processes. The continuous electrospun nanofibers had average diameters ranging from 392 to 903 nm. The addition of biomass tar resulted in increased fiber diameters, reduced thermal stabilities, and slowed cyclization reactions of PAN in the as-spun nanofibers. After stabilization and carbonization, the resultant CNFs showed more uniformly sized and reduced average diameters (226-507 nm) compared to as-spun nanofibers. The CNFs exhibited high specific surface area (>400 m(2)/g) and microporosity, attributed to the combined effects of phase separations of the tar and PAN and thermal decompositions of tar components. These pore characteristics increased the exposures and contacts of silver nanoparticles to the bacteria including Gram-positive Staphylococcus aureus and Gram-negative Escherichia coli, leading to excellent antimicrobial performances of as-spun nanofibers and CNFs. A new strategy is thus provided for utilizing biomass tar as a low-cost precursor to prepare functional CNFs and reduce environmental pollutions associated with direct disposal of tar as an industrial waste.

Estimating tar and nicotine exposure: human smoking versus machine generated smoke yields.

PubMed

St Charles, F K; Kabbani, A A; Borgerding, M F

2010-02-01

Determine human smoked (HS) cigarette yields of tar and nicotine for smokers using their own brand in their everyday environment. A robust, filter analysis method was used to estimate the tar and nicotine yields for 784 subjects. Seventeen brands were chosen to represent a wide range of styles: 85 and 100 mm lengths; menthol and non-menthol; 17, 23, and 25 mm circumference; with tar yields [Federal Trade Commission (FTC) method] ranging from 1 to 18 mg. Tar bands chosen corresponded to yields of 1-3 mg, 4-6 mg, 7-12 mg, and 13+ mg. A significant difference (p<0.0001) in HS yields of tar and nicotine between tar bands was found. Machine-smoked yields were reasonable predictors of the HS yields for groups of subjects, but the relationship was neither exact nor linear. Neither the FTC, the Massachusetts (MA) nor the Canadian Intensive (CI) machine-smoking methods accurately reflect the HS yields across all brands. The FTC method was closest for the 7-12 mg and 13+ mg products and the MA method was closest for the 1-3mg products. The HS yields for the 4-6 mg products were approximately midway between the FTC and the MA yields. HS nicotine yields corresponded well with published urinary and plasma nicotine biomarker studies. 2009 Elsevier Inc. All rights reserved.

Pressure Actuated Leaf Seals for Improved Turbine Shaft Sealing

NASA Technical Reports Server (NTRS)

Grondahl, Clayton

2006-01-01

This presentation introduces a shaft seal in which leaf seal elements are constructed from slotted shim material formed and layered into a frusto-conical assembly. Limited elastic deflection of seal leaves with increasing system pressure close large startup clearance to a small, non-contacting, steady state running clearance. At shutdown seal elements resiliently retract as differential seal pressure diminishes. Large seal clearance during startup and shutdown provides a mechanism for rub avoidance. Minimum operating clearance improves performance and non-contacting operation promises long seal life. Design features of this seal, sample calculations at differential pressures up to 2400 psid and benefit comparison with brush and labyrinth seals is documented in paper, AIAA 2005 3985, presented at the Advanced Seal Technology session of the Joint Propulsion Conference in Tucson this past July. In this presentation use of bimetallic leaf material will be discussed. Frictional heating of bimetallic leaf seals during a seal rub can relieve the rub condition to some extent with a change in seal shape. Improved leaf seal rub tolerance is expected with bimetallic material.

29 CFR 1926.1102 - Coal tar pitch volatiles; interpretation of term.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 8 2014-07-01 2014-07-01 false Coal tar pitch volatiles; interpretation of term. 1926.1102 Section 1926.1102 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH... Hazardous Substances § 1926.1102 Coal tar pitch volatiles; interpretation of term. Note: The requirements...

29 CFR 1926.1102 - Coal tar pitch volatiles; interpretation of term.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 8 2011-07-01 2011-07-01 false Coal tar pitch volatiles; interpretation of term. 1926.1102 Section 1926.1102 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH... Hazardous Substances § 1926.1102 Coal tar pitch volatiles; interpretation of term. Note: The requirements...

29 CFR 1926.1102 - Coal tar pitch volatiles; interpretation of term.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 29 Labor 8 2012-07-01 2012-07-01 false Coal tar pitch volatiles; interpretation of term. 1926.1102 Section 1926.1102 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH... Hazardous Substances § 1926.1102 Coal tar pitch volatiles; interpretation of term. Note: The requirements...

29 CFR 1926.1102 - Coal tar pitch volatiles; interpretation of term.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 8 2010-07-01 2010-07-01 false Coal tar pitch volatiles; interpretation of term. 1926.1102 Section 1926.1102 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH... Hazardous Substances § 1926.1102 Coal tar pitch volatiles; interpretation of term. Note: The requirements...

Experimental studies and performance analyses on polyurethane and nitrile rubber rod seals

NASA Astrophysics Data System (ADS)

Mirza, M.; Temiz, V.; Kamburoǧlu, E.

2012-09-01

The aim of this study is to determine the friction and leakage properties of rod seals made of polyethylene and nitrile rubber with different design geometries, under various pressure and lubricating oil viscosity conditions, in order to make assumptions about their general sealing characteristics and their pros and cons under certain working conditions that involve a range of fluid pressures. The test specimens consist of commercial rod seals of various designs and materials and were mounted on a hard chrome coated shaft subject to reciprocating motion. The test rig is capable of measuring friction force by means of strain measurements on a load cell transmitting the linear motion of a screw shaft to the test shaft. The test results of the reciprocating rod seal samples were evaluated according to leakage amount and friction resistance as a function of materials, design geometries and fluid pressures as well as the lubricating oil viscosity.

Task 3.9 -- Catalytic tar cracking. Semi-annual report, January 1--June 30, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

Young, B.C.; Timpe, R.C.

1995-12-31

Tar produced in the gasification of coal is deleterious to the operation of downstream equipment including fuel cells, gas turbines, hot-gas stream cleanup filters, and pressure swing adsorption systems. Catalytic cracking of tars to smaller hydrocarbons can be an effective means to remove these tars from gas streams and, in the process, generate useful products, e.g., methane gas, which is crucial to the operation of molten carbonate fuel cells. The objectives of this project are to investigate whether gasification tars can be cracked by synthetic nickel-substituted micamontmorillonite, zeolite, or dolomite material; and whether the tars can be cracked selectively bymore » these catalysts to produce a desired liquid and/or gas stream. Results to date are presented in the cited papers.« less

Microwave-induced cracking of pyrolytic tars coupled to microwave pyrolysis for syngas production.

PubMed

Beneroso, D; Bermúdez, J M; Montes-Morán, M A; Arenillas, A; Menéndez, J A

2016-10-01

Herein a new process is proposed to produce a syngas-rich gas fraction (>80vol% H2+CO) from biowaste based on microwave heating within two differentiated steps in order to avoid tars production. The first step consists of the microwave pyrolysis of biowaste induced by a char-based susceptor at 400-800°C; tars, char and syngas-rich gas fractions being produced. The tars are then fed into the second step where a portion of the char from the first step is used as a bed material in a 0.3:1wt% ratio. This bed is heated up by microwaves up to 800°C, allowing thermal cracking of tars and additional syngas (>90vol% H2+CO) being then produced. This new concept arises as an alternative technology to the gasification of biowastes for producing syngas with no need for catalysts or gasifying reagents to minimise tars production. Copyright © 2016 Elsevier Ltd. All rights reserved.

Biodegradable polymer for sealing porous PEO layer on pure magnesium: An in vitro degradation study

NASA Astrophysics Data System (ADS)

Alabbasi, Alyaa; Mehjabeen, Afrin; Kannan, M. Bobby; Ye, Qingsong; Blawert, Carsten

2014-05-01

An attempt was made to seal the porous silicate-based plasma electrolytic oxidation (PEO) layer on pure magnesium (Mg) with a biodegradable polymer, poly(L-lactide) (PLLA), to delay the localized degradation of magnesium-based implants in body fluid for better in-service mechanical integrity. Firstly, a silicate-based PEO coating on pure magnesium was performed using a pulsed constant current method. In order to seal the pores in the PEO layer, PLLA was coated using a two-step spin coating method. The performance of the PEO-PLLA Mg was evaluated using electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization. The EIS results showed that the polarization resistance (Rp) of the PEO-PLLA Mg was close to two orders of magnitude higher than that of the PEO Mg. While the corrosion current density (icorr) of the pure Mg was reduced by 65% with the PEO coating, the PEO-PLLA coating reduced the icorr by almost 100%. As expected, the Rp of the PEO-PLLA Mg decreased with increase in exposure time. However, it was noted that the Rp of the PEO-PLLA Mg even after 100 h was six times higher than that of the PEO Mg after 48 h exposure, and did not show any visible localized attack.

29 CFR 1915.1002 - Coal tar pitch volatiles; interpretation of term.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 7 2014-07-01 2014-07-01 false Coal tar pitch volatiles; interpretation of term. 1915.1002 Section 1915.1002 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH... Toxic and Hazardous Substances § 1915.1002 Coal tar pitch volatiles; interpretation of term. Note: The...

29 CFR 1915.1002 - Coal tar pitch volatiles; interpretation of term.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 7 2011-07-01 2011-07-01 false Coal tar pitch volatiles; interpretation of term. 1915.1002 Section 1915.1002 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH... Toxic and Hazardous Substances § 1915.1002 Coal tar pitch volatiles; interpretation of term. Note: The...

29 CFR 1915.1002 - Coal tar pitch volatiles; interpretation of term.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 29 Labor 7 2013-07-01 2013-07-01 false Coal tar pitch volatiles; interpretation of term. 1915.1002 Section 1915.1002 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH... Toxic and Hazardous Substances § 1915.1002 Coal tar pitch volatiles; interpretation of term. Note: The...

29 CFR 1915.1002 - Coal tar pitch volatiles; interpretation of term.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 29 Labor 7 2012-07-01 2012-07-01 false Coal tar pitch volatiles; interpretation of term. 1915.1002 Section 1915.1002 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH... Toxic and Hazardous Substances § 1915.1002 Coal tar pitch volatiles; interpretation of term. Note: The...

29 CFR 1915.1002 - Coal tar pitch volatiles; interpretation of term.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Coal tar pitch volatiles; interpretation of term. 1915.1002 Section 1915.1002 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH... Toxic and Hazardous Substances § 1915.1002 Coal tar pitch volatiles; interpretation of term. Note: The...

Aviation Turbine Fuels from Tar Sands Bitumen and Heavy Oils. Part 1. Process Analysis.

DTIC Science & Technology

1984-09-01

Uinta Basin .......................too.... 11 b . Asphalt Ridge ........................ 13 c.* Tar Sand Triangle ..... to .. .. . .. .. . 15 e...Estimated ............**..* 7 3 CHARACTERISTICS OF UTAH’S MAJOR TAR SANDS ....... 12 4 UINTA BASIN DEPOSITS ................... *........ 13 *.5 UINTA ...7 UINTA BASIN , UTAH PROPERTIES -SUNNYSIDE ........ 20 8 UINTA BASIN , UTAH PROPERTIES -P. R. SPRINGS . 22 r9 ESTIMATED CALIFORNIA TAR SAND DISTRIBUTION

Identification of sources of tar balls deposited along the Southwest Caspian Coast, Iran using fingerprinting techniques.

PubMed

Shirneshan, Golshan; Bakhtiari, Alireza Riyahi; Memariani, Mahmoud

2016-10-15

In 2012, a significant number of tar balls occurred along the Southwest coasts of the Caspian Sea (Iran). Several oil fields of Turkmenistan, Azerbaijan and Iran might be sources of oil spills and lead to the formation of these tar balls. For source identification, 6 tar ball samples were collected from the Southwest beaches of the Caspian Sea and subjected to fingerprint analysis based on the distribution of the source-specific biomarkers of pentacyclic tri-terpanes and steranes. Comparing the diagenic ratios revealed that the tar balls were chemically similar and originated from the same source. Results of double ratio plots (e.g., C29/C30 versus ∑C31-C35/C30 and C28 αββ/(C27 αββ+C29 αββ) versus C29 αββ/(C27 αββ+C28 αββ)) in the tar balls and oils from Iran, Turkmenistan and Azerbaijan indicated that the tar balls might be the result of spills from Turkmenistan oil. Moreover, principle component analysis (PCA) using biomarker ratios on the tar balls and 20 crude oil samples from different wells of Azerbaijan, Iran and Turkmenistan oils showed that the tar balls collected at the Southwest beaches are highly similar to the Turkmenistan oil but one of the Azerbaijan oils (from Bahar field oils) was found to be also slightly close to the tar balls. The weathering characterizations based on the presence of UCM (unresolved complex mixture) and low/high molecular weight ratios (L/H) of alkanes and PAHs indicated the tar ball samples have been significantly influenced by natural weathering processes such as evaporation, photo-degradation and biodegradation. This is the first study of its kind in Iran to use fingerprinting for source identification of tar balls. Copyright © 2016 Elsevier B.V. All rights reserved.

Coal-tar-based pavement sealcoat—Potential concerns for human health and aquatic life

USGS Publications Warehouse

Mahler, Barbara J.; Woodside, Michael D.; Van Metre, Peter C.

2016-04-20

Aquatic Life Concerns—Runoff from coal-tar-sealcoated pavement, even runoff collected more than 3 months after sealcoat application, is acutely toxic to fathead minnows and water fleas, two species commonly used to assess toxicity to aquatic life. Exposure to even highly diluted runoff from coal-tar-sealcoated pavement can cause DNA damage and impair DNA repair. These findings demonstrate that coal-tar-sealcoat runoff can remain a risk to aquatic life for months after application.

Sealing device for providing a seal in a turbomachine

DOEpatents

Lacy, Benjamin Paul; Kottilingam, Srikanth Chandrudu; Porter, Christopher Donald; Schick, David Edward; Weber, David Wayne

2016-08-16

Sealing device for providing seals between adjacent components, and turbomachines utilizing such sealing devices, are provided. A sealing device includes a seal plate insertable between the adjacent components, the seal plate comprising a first face and an opposing second face. The sealing device further includes a plurality of pins extending from one of the first face or the second face, the plurality of pins configured to space the one of the first face or the second face from contact surfaces of the adjacent components.

Titanium sealing glasses and seals formed therefrom

DOEpatents

Brow, Richard K.; McCollister, Howard L.; Phifer, Carol C.; Day, Delbert E.

1997-01-01

Alkaline-earth lanthanoborate sealing-glass compositions containing CaO, La.sub.2 O.sub.3, B.sub.2 O.sub.3, TiO.sub.2 and Al.sub.2 O.sub.3 in various combinations of mole-% are provided. These sealing-glass compositions are useful for forming hermetic glass-to-metal seals with titanium and titanium alloys that have a high aqueous durability for component or device applications requiring exposure to moisture, water or body fluids. Particular applications of the titanium sealing-glass compositions include forming glass-to-metal seals for lithium batteries and implanted biomedical devices (e.g. batteries, pacemakers, defibrillators, pumps).

Seal assembly

DOEpatents

Johnson, Roger Neal; Longfritz, William David

2001-01-01

A seal assembly that seals a gap formed by a groove comprises a seal body, a biasing element, and a connection that connects the seal body to the biasing element to form the seal assembly. The seal assembly further comprises a concave-shaped center section and convex-shaped contact portions at each end of the seal body. The biasing element is formed from an elastic material and comprises a convex-shaped center section and concave-shaped biasing zones that are opposed to the convex-shaped contact portions. The biasing element is adapted to be compressed to change a width of the seal assembly from a first width to a second width that is smaller than the first width. In the compressed state, the seal assembly can be disposed in the groove. After release of the compressing force, the seal assembly expands. The contact portions will move toward a surface of the groove and the biasing zones will move into contact with another surface of the groove. The biasing zones will bias the contact portions of the seal body against the surface of the groove.

Catalytic decomposition of tar derived from wood waste pyrolysis using Indonesian low grade iron ore as catalyst

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wicakso, Doni Rahmat; Chemical Engineering Department, Faculty of Engineering, Gadjah Mada University, Jalan Grafika No. 2 Bulaksumur, Yogyakarta, 55281; Sutijan

Low grade iron ore can be used as an alternative catalyst for bio-tar decomposition. Compared to other catalysts, such as Ni, Rd, Ru, Pd and Pt, iron ore is cheaper. The objective of this research was to investigate the effect of using low grade iron ore as catalyst for tar catalytic decomposition in fixed bed reactor. Tar used in this experiment was pyrolysis product of wood waste while the catalyst was Indonesian low grade iron ore. The variables studied were temperatures between 500 – 600 °C and catalyst weight between 0 – 40 gram. The first step, tar was evaporatedmore » at 450 °C to produce tar vapor. Then, tar vapor was flowed to fixed bed reactor filled low grade iron ore. Gas and tar vapor from reactor was cooled, then the liquid and uncondensable gas were analyzed by GC/MS. The catalyst, after experiment, was weighed to calculate total carbon deposited into catalyst pores. The results showed that the tar components that were heavy and light hydrocarbon were decomposed and cracked within the iron ore pores to from gases, light hydrocarbon (bio-oil) and carbon, thus decreasing content tar in bio-oil and increasing the total gas product. In conclusion, the more low grade iron ore used as catalyst, the tar content in the liquid decrease, the H{sup 2} productivity increased and calorimetric value of bio-oil increased.« less

Aspirating Seal Development: Analytical Modeling and Seal Test Rig

NASA Technical Reports Server (NTRS)

Bagepalli, Bharat

1996-01-01

This effort is to develop large diameter (22 - 36 inch) Aspirating Seals for application in aircraft engines. Stein Seal Co. will be fabricating the 36-inch seal(s) for testing. GE's task is to establish a thorough understanding of the operation of Aspirating Seals through analytical modeling and full-scale testing. The two primary objectives of this project are to develop the analytical models of the aspirating seal system, to upgrade using GE's funds, GE's 50-inch seal test rig for testing the Aspirating Seal (back-to-back with a corresponding brush seal), test the aspirating seal(s) for seal closure, tracking and maneuver transients (tilt) at operating pressures and temperatures, and validate the analytical model. The objective of the analytical model development is to evaluate the transient and steady-state dynamic performance characteristics of the seal designed by Stein. The transient dynamic model uses a multi-body system approach: the Stator, Seal face and the rotor are treated as individual bodies with relative degrees of freedom. Initially, the thirty-six springs are represented as a single one trying to keep open the aspirating face. Stops (Contact elements) are provided between the stator and the seal (to compensate the preload in the fully-open position) and between the rotor face and Seal face (to detect rub). The secondary seal is considered as part of the stator. The film's load, damping and stiffness characteristics as functions of pressure and clearance are evaluated using a separate (NASA) code GFACE. Initially, a laminar flow theory is used. Special two-dimensional interpolation routines are written to establish exact film load and damping values at each integration time step. Additionally, other user-routines are written to read-in actual pressure, rpm, stator-growth and rotor growth data and, later, to transfer these as appropriate loads/motions in the system-dynamic model. The transient dynamic model evaluates the various motions, clearances

Acoustic Seal

NASA Technical Reports Server (NTRS)

Steinetz, Bruce M. (Inventor)

2006-01-01

The invention relates to a sealing device having an acoustic resonator. The acoustic resonator is adapted to create acoustic waveforms to generate a sealing pressure barrier blocking fluid flow from a high pressure area to a lower pressure area. The sealing device permits noncontacting sealing operation. The sealing device may include a resonant-macrosonic-synthesis (RMS) resonator.

Acoustic seal

NASA Technical Reports Server (NTRS)

Steinetz, Bruce M. (Inventor)

2006-01-01

The invention relates to a sealing device having an acoustic resonator. The acoustic resonator is adapted to create acoustic waveforms to generate a sealing pressure barrier blocking fluid flow from a high pressure area to a lower pressure area. The sealing device permits noncontacting sealing operation. The sealing device may include a resonant-macrosonic-synthesis (RMS) resonator.

Phytotoxicity and Plant Productivity Analysis of Tar-Enriched Biochars

NASA Astrophysics Data System (ADS)

Keller, M. L.; Masiello, C. A.; Dugan, B.; Rudgers, J. A.; Capareda, S. C.

2008-12-01

Biochar is one of the three by-products obtained by the pyrolysis of organic material, the other two being syngas and bio-oil. The pyrolysis of biomass has generated a great amount of interest in recent years as all three by-products can be put toward beneficial uses. As part of a larger project designed to evaluate the hydrologic impact of biochar soil amendment, we generated a biochar through fast pyrolysis (less than 2 minutes) of sorghum stock at 600°C. In the initial biochar production run, the char bin was not purged with nitrogen. This inadvertent change in pyrolysis conditions produced a fast-pyrolysis biochar enriched with tars. We chose not to discard this batch, however, and instead used it to test the impact of tar-enriched biochars on plants. A suite of phytotoxicity tests were run to assess the effects of tar-rich biochar on plant germination and plant productivity. We designed the experiment to test for negative effects, using an organic carbon and nutrient-rich, greenhouse- optimized potting medium instead of soil. We used Black Seeded Simpson lettuce (Lactuca sativa) as the test organism. We found that even when tars are present within biochar, biochar amendment up to 10% by weight caused increased lettuce germination rates and increased biomass productivity. In this presentation, we will report the statistical significance of our germination and biomass data, as well as present preliminary data on how biochar amendment affects soil hydrologic properties.

Titanium sealing glasses and seals formed therefrom

DOEpatents

Brow, R.K.; McCollister, H.L.; Phifer, C.C.; Day, D.E.

1997-12-02

Alkaline-earth lanthanoborate sealing-glass compositions containing CaO, La{sub 2}O{sub 3}, B{sub 2}O{sub 3}, TiO{sub 2} and Al{sub 2}O{sub 3} in various combinations of mole-% are provided. These sealing-glass compositions are useful for forming hermetic glass-to-metal seals with titanium and titanium alloys that have a high aqueous durability for component or device applications requiring exposure to moisture, water or body fluids. Particular applications of the titanium sealing-glass compositions include forming glass-to-metal seals for lithium batteries and implanted biomedical devices (e.g. batteries, pacemakers, defibrillators, pumps). 2 figs.

Carbazole is a naturally occurring inhibitor of angiogenesis and inflammation isolated from antipsoriatic coal tar

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jack L. Arbiser; Baskaran Govindarajan; Traci E. Battle

2006-06-15

Coal tar is one of the oldest and an effective treatment for psoriasis. Coal tar has been directly applied to the skin, or used in combination with UV light as part of the Goeckerman treatment. The use of coal tar has caused long-term remissions in psoriasis, but has fallen out of favor because the treatment requires hospitalization and coal tar is poorly acceptable aesthetically to patients. Thus, determining the active antipsoriatic component of coal tar is of considerable therapeutic interest. We fractionated coal tar into its components, and tested them using the SVR angiogenesis inhibitor assay. Treatment of SVR endothelialmore » cells with coal tar fractions resulted in the isolation of a single fraction with antiangiogenic activity. The active antiangiogenic compound in coal tar is carbazole. In addition to antiangiogenic activity, carbazole inhibited the production of inflammatory IL-15 by human mononuclear cells. IL-15 is elevated in psoriasis and is thought to contribute to psoriatic inflammation. Carbazole treatment also reduced activity of inducible nitric oxide synthase (iNOS), which is proinflammatory and elevated in psoriasis. The effect of carbazole on upstream pathways in human psoriasis was determined, and carbazole was shown to inhibit signal transducer and activator of transcription (stat)3-mediated transcription, which has been shown to be relevant in human psoriasis. IL-15, iNOS, and stat3 activation require the activation of the small GTPase rac for optimal activity. Carbazole was found to inhibit rac activation as a mechanism for its inhibition of downstream inflammatory and angiogenic pathways. Given its antiangiogenic and anti-inflammatory activities, carbazole is likely a major component of the antipsoriatic activity of coal tar. Carbazole and derivatives may be useful in the therapy of human psoriasis.« less

Contamination control in hybrid microelectronic modules. Part 3: Specifications for coating material and process controls

NASA Technical Reports Server (NTRS)

Himmel, R. P.

1975-01-01

Resin systems for coating hybrids prior to hermetic sealing are described. The resin systems are a flexible silicone junction resin system and a flexible cycloaliphatic epoxy resin system. The coatings are intended for application to the hybrid after all the chips have been assembled and wire bonded, but prior to hermetic sealing of the package. The purpose of the coating is to control particulate contamination by immobilizing particles and by passivating the hybrid. Recommended process controls for the purpose of minimizing contamination in hybrid microcircuit packages are given. Emphasis is placed on those critical hybrid processing steps in which contamination is most likely to occur.

Combined effect of starch/montmorillonite coating and passive MAP in antioxidant activity, total phenolics, organic acids and volatile of fresh-cut carrots.

PubMed

Guimarães, Isabela Costa; dos Reis, Kelen Cristina; Menezes, Evandro Galvão Tavares; Borges, Paulo Rogério Siriano; Rodrigues, Ariel Costa; Leal, Renato; Hernandes, Thais; de Carvalho, Elisângela Helena Nunes; Vilas Boas, Eduardo Valério de Barros

2016-01-01

This work evaluates fresh-cut carrots (FCC) coated with montmorillonite (MMT) subjected to passive modified atmosphere packaging. Carrots were sanitized, cooled, peeled and sliced. Half of the FCC were coated with MMT nanoparticle film and the other half were not. All FCCs were packed in a polypropylene rigid tray, covered with a polypropylene rigid lid or sealed with polyethylene + propylene film, in four treatments (RL, rigid lid; RLC, rigid lid + coating; ST, sealed tray; STC, sealed tray + coating). FCCs were stored at 4 °C and were analyzed weekly for 4 weeks (total antioxidant activity by 2,2-diphenyl-1-picryl hydrazyl method and the β-carotene/linoleic acid, phenolic compounds, organic acids and volatile compounds). The use of coating film with starch nanoparticles and a modified atmosphere leads to the preservation of the total antioxidant activity, the volatile and organic acids of FCC.

Reduced tar, nicotine, and carbon monoxide exposure while smoking ultralow- but not low-yield cigarettes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benowitz, N.L.; Jacob, P. III; Yu, L.

An unresolved public health issue is whether some modern cigarettes are less hazardous than other and whether patients who cannot stop smoking should be advised to switch to lower-yield cigarettes. The authors studied tar (estimated by urine mutagenicity), nicotine, and carbon monoxide exposure in habitual smokers switched from their usual brand to high- (15 mg of tar), low- (5 mg of tar), or ultralow-yield (1 mg of tar) cigarettes. There were no differences in exposure comparing high- or low-yield cigarettes, but tar and nicotine exposures were reduced by 49% and 56%, respectively, and carbon monoxide exposure by 36% while smokingmore » ultralow-yield cigarettes. Similarly, in 248 subjects smoking their self-selected brand, nicotine intake, estimated by blood concentrations of its metabolite continine, was 40% lower in those who smoked ultralow but no different in those smoking higher yields of cigarettes. The data indicate that ultralow-yield cigarettes do deliver substantial doses of tar, nicotine, and carbon monoxide, but that exposure are considerably less than for other cigarettes.« less

Pollutant sensitivity of the endangered Tar River Spinymussel as assessed by single chemical and effluent toxicity tests

USGS Publications Warehouse

Augspurger, Thomas P.; Wang, Ning; Kunz, James L.; Ingersoll, Christopher G.

2014-01-01

The federally endangered Tar River spinymussel (Elliptio steinstansana) is endemic to the Tar River and Neuse River systems in North Carolina. The extent to which water quality limits Tar River spinymussels’ recovery is important to establish, and one aspect of that is understanding the species’ pollutant sensitivity. The primary objectives of this study were to 1) develop captive propagation and culture methods for Tar River spinymussels; 2) determine the pollutant sensitivity of captively propagated Tar River spinymussels; 3) examine the utility of the non-endangered yellow lance (Elliptio lanceolata), yellow lampmussel (Lampsilis cariosa) and notched rainbow (Villosa constricta) as surrogates for the Tar River spinymussels’ chemical sensitivity; 4) develop a 7-d method for conducting effluent toxicity tests starting with newly transformed mussels; 5) assess the toxicity of municipal wastewater effluents discharged into the Tar River spinymussels’ current and historic habitat; and, 6) evaluate the protection afforded by existing effluent toxicity test requirements.

Multilayer compressive seal for sealing in high temperature devices

DOEpatents

Chou, Yeong-Shyung [Richland, WA; Stevenson, Jeffry W [Richland, WA

2007-08-21

A mica based compressive seal has been developed exhibiting superior thermal cycle stability when compared to other compressive seals known in the art. The seal is composed of compliant glass or metal interlayers and a sealing (gasket) member layer composed of mica that is infiltrated with a glass forming material, which effectively reduces leaks within the seal. The compressive seal shows approximately a 100-fold reduction in leak rates compared with previously developed hybrid seals after from 10 to about 40 thermal cycles under a compressive stress of from 50 psi to 100 psi at temperatures in the range from 600.degree. C. to about 850.degree. C.

Sealing device

DOEpatents

Garcia-Crespo, Andres Jose

2013-12-10

A sealing device for sealing a gap between a dovetail of a bucket assembly and a rotor wheel is disclosed. The sealing device includes a cover plate configured to cover the gap and a retention member protruding from the cover plate and configured to engage the dovetail. The sealing device provides a seal against the gap when the bucket assemply is subjected to a centrifugal force.

Effects of human chromosome 12 on interactions between Tat and TAR of human immunodeficiency virus type 1.

PubMed Central

Alonso, A; Cujec, T P; Peterlin, B M

1994-01-01

Rates of transcriptions of the human immunodeficiency virus are greatly increased by the viral trans activator Tat. In vitro, Tat binds to the 5' bulge of the trans-activation response (TAR) RNA stem-loop, which is present in all viral transcripts. In human cells, the central loop in TAR and its cellular RNA-binding proteins are also critical for the function of Tat. Previously, we demonstrated that in rodent cells (CHO cells), but not in those which contain the human chromosome 12 (CHO12 cells), Tat-TAR interactions are compromised. In this study, we examined the roles of the bulge and loop in TAR in Tat trans activation in these cells. Whereas low levels of trans activation depended solely on interactions between Tat and the bulge in CHO cells, high levels of trans activation depended also on interactions between Tat and the loop in CHO12 cells. Since the TAR loop binding proteins in these two cell lines were identical and different from their human counterpart, the human chromosome 12 does not encode TAR loop binding proteins. In vivo binding competition studies with TAR decoys confirmed that the binding of Tat to TAR is more efficient in CHO12 cells. Thus, the protein(s) encoded on human chromosome 12 helps to tether Tat to TAR via its loop, which results in high levels of trans activation. Images PMID:8083988

Ceramic high pressure gas path seal

NASA Technical Reports Server (NTRS)

Liotta, G. C.

1987-01-01

Stage 1 ceramic shrouds (high pressure turbine gas path seal) were developed for the GE T700 turbine helicopter engine under the Army/NASA Contract NAS3-23174. This contract successfully proved the viability and benefits of a Stage 1 ceramic shroud for production application. Stage 1 ceramic shrouds were proven by extensive component and engine testing. This Stage 1 ceramic shroud, plasma sprayed ceramic (ZrOs-BY2O3) and bond coating (NiCrAlY) onto a cast metal backing, offers significant engine performance improvement. Due to the ceramic coating, the amount of cooling air required is reduced 20% resulting in a 0.5% increase in horsepower and a 0.3% decrease in specific fuel consumption. This is accomplished with a component which is lower in cost than the current production shroud. Stage 1 ceramic shrouds will be introduced into field service in late 1987.

Influence of cigarette filter ventilation on smokers' mouth level exposure to tar and nicotine.

PubMed

Caraway, John W; Ashley, Madeleine; Bowman, Sheri A; Chen, Peter; Errington, Graham; Prasad, Krishna; Nelson, Paul R; Shepperd, Christopher J; Fearon, Ian M

2017-12-01

Cigarette filter ventilation allows air to be drawn into the filter, diluting the cigarette smoke. Although machine smoking reveals that toxicant yields are reduced, it does not predict human yields. The objective of this study was to investigate the relationship between cigarette filter ventilation and mouth level exposure (MLE) to tar and nicotine in cigarette smokers. We collated and reviewed data from 11 studies across 9 countries, in studies performed between 2005 and 2013 which contained data on MLE from 156 products with filter ventilation between 0% and 87%. MLE among 7534 participants to tar and nicotine was estimated using the part-filter analysis method from spent filter tips. For each of the countries, MLE to tar and nicotine tended to decrease as filter ventilation increased. Across countries, per-cigarette MLE to tar and nicotine decreased as filter ventilation increased from 0% to 87%. Daily MLE to tar and nicotine also decreased across the range of increasing filter ventilation. These data suggest that on average smokers of highly ventilated cigarettes are exposed to lower amounts of nicotine and tar per cigarette and per day than smokers of cigarettes with lower levels of ventilation. Copyright © 2017 British American Tobacco. Published by Elsevier Inc. All rights reserved.

Impact of genetic variants on haematopoiesis in patients with thrombocytopenia absent radii (TAR) syndrome.

PubMed

Manukjan, Georgi; Bösing, Hendrik; Schmugge, Markus; Strauß, Gabriele; Schulze, Harald

2017-11-01

Thrombocytopenia absent radii (TAR) syndrome is clearly defined by the combination of radial aplasia and reduced platelet counts. The genetics of TAR syndrome has recently been resolved and comprises a microdeletion on Chromosome 1 including the RBM8A gene and a single nucleotide polymorphism (SNP) either at the 5' untranslated region (5'UTR) or within the first intron of RBM8A. Although phenotypically readily diagnosed after birth, the genetic determination of particular SNPs in TAR syndrome harbours valuable information to evaluate disease severity and treatment decisions. Here, we present clinical data in a cohort of 38 patients and observed that platelet counts in individuals with 5'UTR SNP are significantly lower compared to patients bearing the SNP in intron 1. Moreover, elevated haemoglobin values could only be assessed in patients with 5'UTR SNP whereas white blood cell count is unaffected, indicating that frequently observed anaemia in TAR patients could also be SNP-dependent whereas leucocytosis does not correlate with genetic background. However, this report on a large cohort provides an overview of important haematological characteristics in TAR patients, facilitating evaluation of the various traits in this disease and indicating the importance of genetic validation for TAR syndrome. © 2017 John Wiley & Sons Ltd.

Technology for the production of Zero Q.I pitch from coal tar

NASA Astrophysics Data System (ADS)

Karthik, K.; Kumar, K. Rajesh; Rao, C. V. Nageswara; Kumar, B. Vinod; Murty, J. V. S.

2013-06-01

Zero Quinoline Insolubles (Q.I) pitch is a special type of pitch obtained from pre-treatment of coal tar, which is converted into pitch. This is used for impregnation of electrodes for improving the strength, electrical properties and also used as a pre-cursor for Mesophase pitch for producing Mesophase pitch based carbon fibers, carbon foam, and Meso carbon micro beads. This paper discusses the technology of Q.I separation from Coal Tar by using decantation of Coal Tar mixed with Heavy Creosote Oil (HC Oil) at different temperatures. By this method we were able to produce the Zero Q.I pitch with a Q.I value of 0.1%.

Creating and maintaining a gas cap in tar sands formations

DOEpatents

Vinegar, Harold J.; Karanikas, John Michael; Dinkoruk, Deniz Sumnu; Wellington, Scott Lee

2010-03-16

Methods for treating a tar sands formation are disclosed herein. Methods for treating a tar sands formation may include providing heat to at least part of a hydrocarbon layer in the formation from one or more heaters located in the formation. Pressure may be allowed to increase in an upper portion of the formation to provide a gas cap in the upper portion. At least some hydrocarbons are produced from a lower portion of the formation.

Effective prime coats for compacted pavement bases.

DOT National Transportation Integrated Search

2010-08-01

Prime coats have long been used to seal the surface pores in the base, thus reducing the migration of moisture : and absorption of the first application of surface treatment binder, strengthen the granular base near its : surface by binding the finer...

Exosomes from HIV-1-infected Cells Stimulate Production of Pro-inflammatory Cytokines through Trans-activating Response (TAR) RNA*

PubMed Central

Sampey, Gavin C.; Saifuddin, Mohammed; Schwab, Angela; Barclay, Robert; Punya, Shreya; Chung, Myung-Chul; Hakami, Ramin M.; Asad Zadeh, Mohammad; Lepene, Benjamin; Klase, Zachary A.; El-Hage, Nazira; Young, Mary; Iordanskiy, Sergey; Kashanchi, Fatah

2016-01-01

HIV-1 infection results in a chronic illness because long-term highly active antiretroviral therapy can lower viral titers to an undetectable level. However, discontinuation of therapy rapidly increases virus burden. Moreover, patients under highly active antiretroviral therapy frequently develop various metabolic disorders, neurocognitive abnormalities, and cardiovascular diseases. We have previously shown that exosomes containing trans-activating response (TAR) element RNA enhance susceptibility of undifferentiated naive cells to HIV-1 infection. This study indicates that exosomes from HIV-1-infected primary cells are highly abundant with TAR RNA as detected by RT-real time PCR. Interestingly, up to a million copies of TAR RNA/μl were also detected in the serum from HIV-1-infected humanized mice suggesting that TAR RNA may be stable in vivo. Incubation of exosomes from HIV-1-infected cells with primary macrophages resulted in a dramatic increase of proinflammatory cytokines, IL-6 and TNF-β, indicating that exosomes containing TAR RNA could play a direct role in control of cytokine gene expression. The intact TAR molecule was able to bind to PKR and TLR3 effectively, whereas the 5′ and 3′ stems (TAR microRNAs) bound best to TLR7 and -8 and none to PKR. Binding of TAR to PKR did not result in its phosphorylation, and therefore, TAR may be a dominant negative decoy molecule in cells. The TLR binding through either TAR RNA or TAR microRNA potentially can activate the NF-κB pathway and regulate cytokine expression. Collectively, these results imply that exosomes containing TAR RNA could directly affect the proinflammatory cytokine gene expression and may explain a possible mechanism of inflammation observed in HIV-1-infected patients under cART. PMID:26553869

Physicochemical Approaches for the Remediation of Former Manufactured Gas Plant Tars

NASA Astrophysics Data System (ADS)

Hauswirth, S.; Miller, C. T.

2014-12-01

Former manufactured gas plant (FMGP) tars are one of the most challenging non-aqueous phase liquid (NAPL) contaminants to remediate due to their complex chemical composition, high viscosities, and ability to alter wettability. In this work, we investigate several in situ remediation techniques for the removal of tar from porous media. Batch and column experiments were conducted to test the effectiveness of mobilization, solubilization, and chemical oxidation remediation approaches. Alkaline (NaOH), surfactant (Triton X-100), and polymer (xanthan gum) agents were used in various combinations to reduce tar-water interfacial tension, increase flushing solution viscosity, and increase the solubilities of tar components. Base-activated sodium persulfate was used alone and in combination with surfactant to chemically oxidized tar components. The effectiveness of each method was assessed in terms of both removal of PAHs from the system and reduction of dissolved-phase effluent polycyclic aromatic hydrocarbon (PAH) concentrations. In column studies, alkaline-polymer (AP) and alkaline-surfactant-polymer (ASP) solutions efficiently mobilized 81-93% and 95-96% of residual PAHs, respectively, within two pore volumes. The impact of AP flushing on dissolved-phase PAH concentrations was relatively low; however, the concentrations of several low molar mass PAHs were significantly reduced after ASP flushing. Surfactant-polymer (SP) solutions removed over 99% of residual PAHs through a combination of mobilization and solubilization, and reduced the post-remediation, dissolved-phase total PAH concentration by 98.4-99.1%. Degradation of residual PAHs by base-activated sodium persulfate was relatively low (30-50%), and had little impact on dissolved-phase PAH concentrations.

Thermal Cracking of Tars in a Continuously Fed Reactor with Steam

DTIC Science & Technology

2011-05-01

Fluidized Bed using biomass 8 Tars  Mixture of organic components present in gasification product gas with high molecular weight hydrocarbons [MW...Disable sulfur removal systems FoulingPlugging [Ref. 3: Biomass Gasification – Tar and Particles in Product Gases Sampling and Analysis”, European...P., and Nussbaumer T., “Gas Cleaning Requirements for Internal Combustion Engine Applications of Fixed Bed Biomass Gasification ”, Biomass and

Cold Preparation of Heroin in a Black Tar Market.

PubMed

Roth, Alexis M; Armenta, Richard F; Wagner, Karla D; Strathdee, Steffanie A; Goldshear, Jesse L; Cuevas-Mota, Jazmine; Garfein, Richard S

2017-07-29

Black tar heroin is typically prepared for injection with heat which decreases the risk of HIV transmission by inactivating the virus. We received reports that persons who inject drugs (PWID) in Tijuana, Baja California, Mexico, a black tar heroin market, were using only water to dissolve heroin. Because Tijuana abuts San Diego County, CA, United States, we undertook the present analyses to determine the prevalence of this practice among PWID in San Diego, California. PWID completed quarterly behavioral assessments and serological testing for blood-borne viruses. Bivariate and multivariable logistic regression models were constructed to assess for individual, social, and structural correlates of preparing heroin without heat within the preceding 6 months. Nearly half of black tar heroin users (149/305) reported they had prepared heroin without heat within 6 months. In multivariable analysis, cold preparation was independently associated with younger age (10 year decrease; AOR = 1.25; 95% CI 1.03, 1.53), more drug injecting acquaintances (per 5 acquaintance increase; AOR = 1.05; 95% CI 1.01, 1.09) and prefilled syringe use (injecting drugs from syringes that are already filled with drugs before purchase; AOR = 1.86; 95% CI 1.14, 3.02). Conclusions/Importance: To our knowledge, this is the first paper to report that PWID living in a black tar heroin market are preparing heroin without heat. Additional research is needed to determine whether this is an endemic practice or PWID are engaging in new forms of drug preparation in response to changes in the environment.

The Auxin Biosynthetic TRYPTOPHAN AMINOTRANSFERASE RELATED TaTAR2.1-3A Increases Grain Yield of Wheat.

PubMed

Shao, An; Ma, Wenying; Zhao, Xueqiang; Hu, Mengyun; He, Xue; Teng, Wan; Li, Hui; Tong, Yiping

2017-08-01

Controlling the major auxin biosynthetic pathway to manipulate auxin content could be a target for genetic engineering of crops with desired traits, but little progress had been made because low or high auxin contents often cause developmental inhibition. Here, we performed a genome-wide analysis of bread wheat ( Triticum aestivum ) to identify the Tryptophan Aminotransferase of Arabidopsis1/Tryptophan Aminotransferase-Related (TAA1/TAR) genes that function in the tryptophan-dependent pathway of auxin biosynthesis. Sequence mining together with gene cloning identified 15 TaTAR genes, among which 12 and three genes were phylogenetically close to Arabidopsis ( Arabidopsis thaliana ) AtTAR2 and AtTAR3, respectively. TaTAR2.1 had the most abundant transcripts in the TaTAR2 genes and was expressed mainly in roots and up-regulated by low nitrogen (N) availability. Knockdown of TaTAR2.1 caused vegetative and reproductive deficiencies and impaired lateral root (LR) growth under both high- and low-N conditions. Overexpressing TaTAR2.1-3A in wheat enhanced LR branching, plant height, spike number, grain yield, and aerial N accumulation under different N supply levels. In addition, overexpressing TaTAR2.1-3A in Arabidopsis elevated auxin accumulation in the primary root tip, LR tip, LR primordia, and cotyledon and hypocotyl and increased primary root length, visible LR number, and shoot fresh weight under high- and low-N conditions. Our results indicate that TaTAR2.1 is critical for wheat growth and also shows potential for genetic engineering to reach the aim of improving the grain yield of wheat. © 2017 American Society of Plant Biologists. All Rights Reserved.

Use of mineral oil Fleet enema for the removal of a large tar burn: a case report.

PubMed

Carta, Tricia; Gawaziuk, Justin; Liu, Song; Logsetty, Sarvesh

2015-03-01

Extensive hot tar burns are relatively uncommon. Management of these burns provides a significant clinical challenge especially with respect to tar removal involving a large total body surface area (TBSA), without causing further tissue injury. We report a case of an over 40-year old male construction worker who was removing a malfunctioning cap from broken valve. This resulted in tar spraying over the anterior surface of his body including legs, feet, chest, abdomen, arms, face and oral cavity (80% TBSA covered in tar resulting in a 50% TBSA burn injury). Initially, petrolatum-based, double antibiotic ointment was used to remove the tar, based on our previous experience with small tar burns. However, this was time-consuming and ineffective. The tar was easily removed with mineral oil without irritation. In order to meet the demand for quantity of mineral oil, the pharmacy suggested using mineral oil Fleet enema (C.B. Fleet Company, Inc., Lynchburg, Virginia, USA). The squeezable bottle and catheter tip facilitated administration of oil into the patient's construction boots and under clothing that was adhered to the patient's skin. Tar removal requires an effective, non-toxic and non-irritating agent. Mineral oil is such an agent. For patients that may present with a large surface area tar burn, using mineral oil Fleet enema is a viable option that facilitates application into difficult areas. Grant Support: The Firefighters' Burn Fund (Manitoba) supported this project. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

Stresses in sulfuric acid anodized coatings on aluminum

NASA Technical Reports Server (NTRS)

Alwitt, R. S.; Xu, J.; Mcclung, R. C.

1993-01-01

Stresses in porous anodic alumina coatings have been measured for specimens stabilized in air at different temperatures and humidities. In ambient atmosphere the stress is tensile after anodic oxidation and is compressive after sealing. Exposure to dry atmosphere causes the stress to change to strongly tensile, up to 110 MPa. The stress increase is proportional to the loss of water from the coating. These changes are reversible with changes in humidity. Similar reversible effects occur upon moderate temperature changes. The biaxial modulus of the coating is about 100 GPa.

Partitioning studies of coal-tar constituents in a two-phase contaminated ground-water system

USGS Publications Warehouse

Rostad, C.E.; Pereira, W.E.; Hult, M.F.

1985-01-01

Organic compounds derived from coal-tar wastes in a contaminated aquifer in St. Louis Park, Minnesota, were identified, and their partition coefficients between the tar phase and aqueous phase were determined and compared with the corresponding n-octanol/water partition coefficients. Coal tar contains numerous polycyclic aromatic compounds, many of which are suspected carcinogens or mutagens. Groundwater contamination by these toxic compounds may pose an environmental health hazard in nearby public water-supply wells. Fluid samples from this aquifer developed two phases upon settling: an upper aqueous phase, and a lower oily-tar phase. After separating the phases, polycyclic aromatic compounds in each phase were isolated using complexation with N-methyl-2-pyrrolidone and identified by fused-silica capillary gas chromatography/mass spectrometry. Thirty-one of the polycyclic aromatic compounds were chosen for further study from four different classes: 12 polycyclic aromatic hydrocarbons, 10 nitrogen heterocycles, 5 sulfur heterocycles, and 4 oxygen heterocycles. Within each compound class, the tar/water partition coefficients of these compounds were reasonably comparable with the respective n-octanol/water partition coefficient.

Coining seal

DOEpatents

Mancebo, Lloyd

1976-01-01

A bakeable high pressure-vacuum seal is provided in which an inductile sealing element having a butterfly shaped crosssection with protruding sharp edges at each of the four corners, is sandwiched between two ductile sealing elements, the sandwiched assembly then being compressed between the surfaces of the flange elements of a high pressure or high vacuum vessel to coin the ductile sealing element into the surface of the inductile sealing element as well as the surfaces of the flange elements.

Preparation and Performance of Plasma/Polymer Composite Coatings on Magnesium Alloy

NASA Astrophysics Data System (ADS)

Bakhsheshi-Rad, H. R.; Hamzah, E.; Bagheriyan, S.; Daroonparvar, M.; Kasiri-Asgarani, M.; Shah, A. M.; Medraj, M.

2016-09-01

A triplex plasma (NiCoCrAlHfYSi/Al2O3·13%TiO2)/polycaprolactone composite coating was successfully deposited on a Mg-1.2Ca alloy by a combination of atmospheric plasma spraying and dip-coating techniques. The NiCoCrAlHfYSi (MCrAlHYS) coating, as the first layer, contained a large number of voids, globular porosities, and micro-cracks with a thickness of 40-50 μm, while the Al2O3·13%TiO2 coating, as the second layer, presented a unique bimodal microstructure with a thickness of 70-80 μm. The top layer was a hydrophobic polymer, which effectively sealed the porosities of plasma layers. The results of micro-hardness and bonding strength tests showed that the plasma coating presented excellent hardness (870 HV) and good bonding strength (14.8 MPa). However, the plasma/polymer coatings interface exhibited low bonding strength (8.6 MPa). The polymer coating formed thick layer (100-110 μm) that homogeneously covered the surface of the plasma layers. Contact angle measurement showed that polymer coating over plasma layers significantly decreased surface wettability. The corrosion current density ( i corr) of an uncoated sample (262.7 µA/cm2) decreased to 76.9 µA/cm2 after plasma coatings were applied. However, it was found that the i corr decreased significantly to 0.002 µA/cm2 after polymer sealing of the porous plasma layers.

High temperature braided rope seals for static sealing applications

NASA Technical Reports Server (NTRS)

Adams, Michael L.; Olsen, Andrew; Darolia, Ram; Steinetz, Bruce M.; Bartolotta, Paul A.

1996-01-01

Achieving efficiency and performance goals of advanced aircraft and industrial systems are leading designers to implement high temperature materials such as ceramics and intermetallics. Generally these advanced materials are applied selectively in the highest temperature sections of the engine system including the combustor and high pressure turbine, amongst others. Thermal strains that result in attaching the low expansion-rate components to high expansion rate superalloy structures can cause significant life reduction in the components. Seals are being designed to both seal and to serve as compliant mounts allowing for relative thermal growths between high temperature but brittle primary structures and the surrounding support structures. Designers require high temperature, low-leakage, compliant seals to mitigate thermal stresses and control parasitic and cooling airflow between structures. NASA is developing high temperature braided rope seals in a variety of configurations to help solve these problems. This paper will describe the types of seals being developed, describe unique test techniques used to assess seal performance, and present leakage flow data under representative pressure, temperature and scrubbing conditions. Feasibility of the braided rope seals for both an industrial tube seal and a turbine vane seal application is also demonstrated.

Morphology of transverse aeolian ridges (TARs) on Mars from a large sample: Further evidence of a megaripple origin?

NASA Astrophysics Data System (ADS)

Hugenholtz, Chris H.; Barchyn, Thomas E.; Boulding, Adam

2017-04-01

Using HiRISE digital terrain models (DTMs), we developed a large morphological dataset to examine the three-dimensional shape, size, and scaling of Martian transverse aeolian ridges (TARs). Considerable debate exists on the characteristic morphology of TARs and the origins of these enigmatic bedforms. Some researchers suggest polygenesis or multiple classes of similar bedforms. Reliably characterizing the morphology of TARs is an essential prerequisite to developing and evaluating process-based models of TAR genesis and unraveling aeolian processes on the surface of Mars. We present measurements of TAR morphology from a large, DTM-derived dataset (n = 2295). We focused on TARs with 'simple' morphologies in order enable more defensible discretization. Histograms and cumulative log-frequency plots of morphometric parameters (length, width, height, elongation ratio, and wavelength) indicate the sample represents a continuum of bedforms from a single population. A typical TAR from our dataset is 88.5 m long (longest planview axis), 17.3 m wide (shortest planview axis), 1.3 m tall, and has a wavelength of 25.8 m. Combined with these data, the bulk of evidence presented to date suggests that interpreting TARs as megaripples is the most viable working hypothesis.

Mechanical seal assembly

DOEpatents

Kotlyar, Oleg M.

2001-01-01

An improved mechanical seal assembly is provided for sealing rotating shafts with respect to their shaft housings, wherein the rotating shafts are subject to substantial axial vibrations. The mechanical seal assembly generally includes a rotating sealing ring fixed to the shaft, a non-rotating sealing ring adjacent to and in close contact with the rotating sealing ring for forming an annular seal about the shaft, and a mechanical diode element that applies a biasing force to the non-rotating sealing ring by means of hemispherical joint. The alignment of the mechanical diode with respect to the sealing rings is maintained by a series of linear bearings positioned axially along a desired length of the mechanical diode. Alternative embodiments include mechanical or hydraulic amplification components for amplifying axial displacement of the non-rotating sealing ring and transferring it to the mechanical diode.

Mechanical seal assembly

DOEpatents

Kotlyar, Oleg M.

2002-01-01

An improved mechanical seal assembly is provided for sealing rotating shafts with respect to their shaft housings, wherein the rotating shafts are subject to substantial axial vibrations. The mechanical seal assembly generally includes a rotating sealing ring fixed to the shaft, a non-rotating sealing ring adjacent to and in close contact with the rotating sealing ring for forming an annular seal about the shaft, and a mechanical diode element that applies a biasing force to the non-rotating sealing ring by means of hemispherical joint. The alignment of the mechanical diode with respect to the sealing rings is maintained by a series of linear bearings positioned axially along a desired length of the mechanical diode. Alternative embodiments include mechanical or hydraulic amplification components for amplifying axial displacement of the non-rotating sealing ring and transfering it to the mechanical diode.

TarPmiR: a new approach for microRNA target site prediction.

PubMed

Ding, Jun; Li, Xiaoman; Hu, Haiyan

2016-09-15

The identification of microRNA (miRNA) target sites is fundamentally important for studying gene regulation. There are dozens of computational methods available for miRNA target site prediction. Despite their existence, we still cannot reliably identify miRNA target sites, partially due to our limited understanding of the characteristics of miRNA target sites. The recently published CLASH (crosslinking ligation and sequencing of hybrids) data provide an unprecedented opportunity to study the characteristics of miRNA target sites and improve miRNA target site prediction methods. Applying four different machine learning approaches to the CLASH data, we identified seven new features of miRNA target sites. Combining these new features with those commonly used by existing miRNA target prediction algorithms, we developed an approach called TarPmiR for miRNA target site prediction. Testing on two human and one mouse non-CLASH datasets, we showed that TarPmiR predicted more than 74.2% of true miRNA target sites in each dataset. Compared with three existing approaches, we demonstrated that TarPmiR is superior to these existing approaches in terms of better recall and better precision. The TarPmiR software is freely available at http://hulab.ucf.edu/research/projects/miRNA/TarPmiR/ CONTACTS: haihu@cs.ucf.edu or xiaoman@mail.ucf.edu Supplementary data are available at Bioinformatics online. © The Author 2016. Published by Oxford University Press.

Tar analysis from biomass gasification by means of online fluorescence spectroscopy

NASA Astrophysics Data System (ADS)

Baumhakl, Christoph; Karellas, Sotirios

2011-07-01

Optical methods in gas analysis are very valuable mainly due to their non-intrusive character. That gives the possibility to use them for in-situ or online measurements with only optical intervention in the measurement volume. In processes like the gasification of biomass, it is of high importance to monitor the gas quality in order to use the product gas in proper machines for energy production following the restrictions in the gas composition but also improving its quality, which leads to high efficient systems. One of the main problems in the biomass gasification process is the formation of tars. These higher hydrocarbons can lead to problems in the operation of the energy system. Up to date, the state of the art method used widely for the determination of tars is a standardized offline measurement system, the so-called "Tar Protocol". The aim of this work is to describe an innovative, online, optical method for determining the tar content of the product gas by means of fluorescence spectroscopy. This method uses optical sources and detectors that can be found in the market at low cost and therefore it is very attractive, especially for industrial applications where cost efficiency followed by medium to high precision are of high importance.

Glass sealing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brow, R.K.; Kovacic, L.; Chambers, R.S.

1996-04-01

Hernetic glass sealing technologies developed for weapons component applications can be utilized for the design and manufacture of fuel cells. Design and processing of of a seal are optimized through an integrated approach based on glass composition research, finite element analysis, and sealing process definition. Glass sealing procedures are selected to accommodate the limits imposed by glass composition and predicted calculations.

Modeling the impact of bubbling bed hydrodynamics on tar yield and its fluctuations during biomass fast pyrolysis

DOE PAGES

Xiong, Qingang; Ramirez, Emilio; Pannala, Sreekanth; ...

2015-10-09

The impact of bubbling bed hydrodynamics on temporal variations in the exit tar yield for biomass fast pyrolysis was investigated using computational simulations of an experimental laboratory-scale reactor. A multi-fluid computational fluid dynamics model was employed to simulate the differential conservation equations in the reactor, and this was combined with a multi-component, multi-step pyrolysis kinetics scheme for biomass to account for chemical reactions. The predicted mean tar yields at the reactor exit appear to match corresponding experimental observations. Parametric studies predicted that increasing the fluidization velocity should improve the mean tar yield but increase its temporal variations. Increases in themore » mean tar yield coincide with reducing the diameter of sand particles or increasing the initial sand bed height. However, trends in tar yield variability are more complex than the trends in mean yield. The standard deviation in tar yield reaches a maximum with changes in sand particle size. As a result, the standard deviation in tar yield increases with the increases in initial bed height in freely bubbling state, while reaches a maximum in slugging state.« less

A two-step sealing-and-reinforcement SU8 bonding paradigm for the fabrication of shallow microchannels

NASA Astrophysics Data System (ADS)

Mehboudi, Aryan; Yeom, Junghoon

2018-03-01

Adhesive bonding is a key technique to create microfluidic devices when two separate substrates are used to form microchannels. Among many adhesives explored in microchannel fabrication, SU8 has been widely used as an adhesive layer for sealing the microchannel sidewalls. The majority of the available SU8-based bonding methods, however, suffer from the difficulties associated with sealing of two important types of the microchannel architecture: (1) shallow microchannels with small patterns on a large area, and (2) microchannels with ultra-low aspect ratios (e.g. 6 mm in width and 2~μ m in height). In this paper, a new bonding paradigm based upon the low-temperature and low-pressure SU8 bonding, consisting of two steps of sealing using a thin-SU8-coated PET film and bonding reinforcement using a SU8-coated glass slide, is proposed to resolve the aforementioned difficulties. Since it does not need complicated instruments such as a wafer bonding machine and a lamination device, the developed bonding paradigm is convenient and economical. We successfully demonstrate the compatibility of the proposed bonding paradigm with the two microchannel fabrication approaches based on the glass wet etching and the SU8 photo-lithography, where small microchannels with the innermost surfaces fully made of SU8 are obtained. A theoretical model is employed to better investigate the flow characteristics and the structural behavior of the microchannel including the PET film deformation, strain and von Mises stress distributions, bonding strength, etc. Moreover, we demonstrate the fabrication of the multi-height deep-shallow microchannel sidewalls and their sealing using the SU8-coated PET film. Finally, as a proof-of-concept device, a microfluidic filter consisting of the double-height deep-shallow microchannel is fabricated for separation of 3 µm and 10 µm particles.

Rotary kiln seal

DOEpatents

Drexler, Robert L.

1992-01-01

A rotary seal used to prevent the escape of contaminates from a rotating kiln incinerator. The rotating seal combines a rotating disc plate which is attached to the rotating kiln shell and four sets of non-rotating carbon seal bars housed in a primary and secondary housing and which rub on the sides of the disc. A seal air system is used to create a positive pressure in a chamber between the primary and secondary seals to create a positive air flow into the contaminated gas chamber. The seal air system also employs an air inlet located between the secondary and tertiary seals to further insure that no contaminates pass the seal and enter the external environment and to provide makeup air for the air which flows into the contaminated gas chamber. The pressure exerted by the seal bars on the rotating disc is controlled by means of a preload spring. The seal is capable of operating in a thermally changing environment where the both radial expansion and axial movement of the rotating kiln do not result in the failure of the seal.

Skin cancer in patients with psoriasis treated with coal tar. A 25-year follow-up study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pittelkow, M.R.; Perry, H.O.; Muller, S.A.

1981-08-01

For many years, crude coal tar has been used for the treatment of psoriasis. The possible carcinogenic effect of crude coal tar and ultraviolet (UV) radiation (Goeckerman regimen), considered individually or in combination, has been of some concern to physicians. A 25-year follow-up study was completed on 280 patients with psoriasis who were hospitalized and treated with crude coal tar and UV radiation at the Mayo Clinic, Rochester, Minn, during the years 1950 through 1954. The results of this study suggest that the incidence of skin cancer is not appreciably increased above the expected incidence for the general population whenmore » patients are treated with coal tar ointments. It seems that the Goeckerman regimen (topical crude coal tar combined with UV radiation) can be used with minimal risk for skin cancer in the treatment of psoriasis.« less

Improvement of the tissue-adhesive and sealing effect of fibrin sealant using polyglycolic acid felt.

PubMed

Shinya, Noriko; Oka, Shirou; Miyabashira, Sumika; Kaetsu, Hiroshi; Uchida, Takanori; Sueyoshi, Masuo; Takase, Kozo; Akuzawa, Masao; Miyamoto, Atsushi; Shigaki, Takamichi

2009-01-01

Although fibrin sealant (FS) has an advantage of high biocompatibility, its adhesive force and sealing effect have been generally considered to be inadequate. In the present study, a high adhesive force and sealing effect were obtained by first rubbing fibrinogen solution into the target tissue, attaching polyglycolic acid (PGA) felt to the treated area, and finally spraying it with FS. This method was compared with three conventional FS application methods and a method using fibrin glue-coated collagen fleece. The adhesive force resulting from the present method was 12 times higher than that for the sequential application method, 4.5 times higher than the spray method, 2.5 times higher than the rubbing and spray method, and 2.2 times higher than the use of fibrin glue-coated collagen fleece. The high adhesive force of FS with PGA felt seemed to be due the high fibrin content of the fibrin gel (FG). Light and electron microscopic observations suggested that the formation of FG in closer contact with the muscle fibers was a factor contributing to this superior adhesive force. Comparison of the sealing effect of the present method with other methods using various biomaterials in combination with FS showed that the sealing effect of FS with PGA felt was 1.4 times higher that of polyglactin 910, 1.8 times that of polytetrafluoroethylene, and 6.7 times that of oxidized regenerated cellulose.

Iron(II) supramolecular helicates interfere with the HIV-1 Tat–TAR RNA interaction critical for viral replication

PubMed Central

Malina, Jaroslav; Hannon, Michael J.; Brabec, Viktor

2016-01-01

The interaction between the HIV-1 transactivator protein Tat and TAR (transactivation responsive region) RNA, plays a critical role in HIV-1 transcription. Iron(II) supramolecular helicates were evaluated for their in vitro activity to inhibit Tat–TAR RNA interaction using UV melting studies, electrophoretic mobility shift assay, and RNase A footprinting. The results demonstrate that iron(II) supramolecular helicates inhibit Tat-TAR interaction at nanomolar concentrations by binding to TAR RNA. These studies provide a new insight into the biological potential of metallosupramolecular helicates. PMID:27405089

Iron(II) supramolecular helicates interfere with the HIV-1 Tat-TAR RNA interaction critical for viral replication.

PubMed

Malina, Jaroslav; Hannon, Michael J; Brabec, Viktor

2016-07-12

The interaction between the HIV-1 transactivator protein Tat and TAR (transactivation responsive region) RNA, plays a critical role in HIV-1 transcription. Iron(II) supramolecular helicates were evaluated for their in vitro activity to inhibit Tat-TAR RNA interaction using UV melting studies, electrophoretic mobility shift assay, and RNase A footprinting. The results demonstrate that iron(II) supramolecular helicates inhibit Tat-TAR interaction at nanomolar concentrations by binding to TAR RNA. These studies provide a new insight into the biological potential of metallosupramolecular helicates.

Nozzle seal

DOEpatents

Groff, Russell Dennis; Vatovec, Richard John

1978-06-11

In an illustrative embodiment of the invention, a nuclear reactor pressure vessel, having an internal hoop from which the heated coolant emerges from the reactor core and passes through to the reactor outlet nozzles, is provided with annular sealing members operatively disposed between the outlet nozzle and the hoop and partly within a retaining annulus formed in the hoop. The sealing members are biased against the pressure vessel and the hoop and one of the sealing members is provided with a piston type pressure ring sealing member which effectively closes the path between the inlet and outlet coolants in the region about the outlet nozzle establishing a leak-proof condition. Furthermore, the flexible responsiveness of the seal assures that the seal will not structurally couple the hoop to the pressure vessel.

Regenerator seal design

DOEpatents

Eckart, Francis H.

1982-01-01

A rotary regenerator disc matrix has a face seal with a cross arm and arcuate rim segments joined by prestress clamps to prestrain the arcuate rim seals so as to compensate seal rim twisting or coning and resultant disc face seal leakage as produced by operating thermal gradients across the seal.

Relative performance comparison between baseline labyrinth and dual-brush compressor discharge seals in a T-700 engine test

NASA Technical Reports Server (NTRS)

Hendricks, Robert C.; Griffin, Thomas A.; Kline, Teresa R.; Csavina, Kristine R.; Pancholi, Arvind; Sood, Devendra

1995-01-01

In separate series of YT-700 engine tests, direct comparisons were made between the forward-facing labyrinth and dual brush compressor discharge seals. Compressor speeds to 43 000 rpm, surface speeds to 160 m/s (530 ft/s), pressures to 1 MPa (145 psi), and temperatures to 680 K (765 F) characterized these tests. The wear estimate for 46 hr of engine operations was less than 0.025 mm (0.001 in.) of the Haynes 25 alloy bristles running against a chromium-carbide-coated rub runner. The pressure drops were higher for the dual-brush seal than for the forward-facing labyrinth seal and leakage was lower-with the labyrinth seal leakage being 2-1/2 times greater-implying better seal characteristics, better secondary airflow distribution, and better engine performance (3 percent at high pressure to 5 percent at lower pressure) for the brush seal. (However, as brush seals wear down (after 500 to 1000 hr of engine operation), their leakage rates will increase.) Modification of the secondary flow path requires that changes in cooling air and engine dynamics be accounted for.

Conformable seal

DOEpatents

Neef, W.S.; Lambert, D.R.

1982-08-10

Sealing apparatus and method, comprising first and second surfaces or membranes, at least one of which surfaces is deformable, placed in proximity to one another. Urging means cause these surfaces to contact one another in a manner such that the deformable surface deforms to conform to the geometry of the other surface, thereby creating a seal. The seal is capable of undergoing multiple cycles of sealing and unsealing.

Sealing performance of a magnetic fluid seal for rotary blood pumps.

PubMed

Mitamura, Yoshinori; Takahashi, Sayaka; Kano, Kentaro; Okamoto, Eiji; Murabayashi, Shun; Nishimura, Ikuya; Higuchi, Taka-Aki

2009-09-01

A magnetic fluid (MF) for a rotary blood pump seal enables mechanical contact-free rotation of the shaft and, hence, has excellent durability. The performance of a MF seal, however, has been reported to decrease in liquids. We have developed a MF seal that has a "shield" mechanism and a new MF with a higher magnetization of 47.9 kA/m. The sealing performance of the MF seal installed in a rotary blood pump was studied. Under the condition of continuous flow, the MF seal remained in perfect condition against a pressure of 298 mm Hg (pump flow rate: 3.96 L/min). The seal was also perfect against a pressure of 170 mm Hg in a continuous flow of 3.9 L/min for 275 days. We have developed a MF seal that works in liquid against clinically used pressures. The MF seal is promising as a shaft seal for rotary blood pumps.

Crystallization and preliminary X-ray diffraction analysis of the periplasmic domain of the Escherichia coli aspartate receptor Tar and its complex with aspartate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mise, Takeshi; Matsunami, Hideyuki; Samatey, Fadel A.

The periplasmic domain of the E. coli aspartate receptor Tar was cloned, expressed, purified and crystallized with and without bound ligand. The crystals obtained diffracted to resolutions of 1.58 and 1.95 Å, respectively. The cell-surface receptor Tar mediates bacterial chemotaxis toward an attractant, aspartate (Asp), and away from a repellent, Ni{sup 2+}. To understand the molecular mechanisms underlying the induction of Tar activity by its ligands, the Escherichia coli Tar periplasmic domain with and without bound aspartate (Asp-Tar and apo-Tar, respectively) were each crystallized in two different forms. Using ammonium sulfate as a precipitant, crystals of apo-Tar1 and Asp-Tar1 weremore » grown and diffracted to resolutions of 2.10 and 2.40 Å, respectively. Alternatively, using sodium chloride as a precipitant, crystals of apo-Tar2 and Asp-Tar2 were grown and diffracted to resolutions of 1.95 and 1.58 Å, respectively. Crystals of apo-Tar1 and Asp-Tar1 adopted space group P4{sub 1}2{sub 1}2, while those of apo-Tar2 and Asp-Tar2 adopted space groups P2{sub 1}2{sub 1}2{sub 1} and C2, respectively.« less

30 CFR 57.22218 - Seals and stoppings (III, V-A, and V-B mines).

Code of Federal Regulations, 2013 CFR

2013-07-01

... materials may be used in face areas. (b) Exposed surfaces on the intake side of stoppings constructed of... construction shall be solid. (c) Exposed surfaces on the fresh air side of seals constructed of combustible... other coatings with equivalent fire resistance. Stoppings constructed to phenolic foam blocks at least...

30 CFR 57.22218 - Seals and stoppings (III, V-A, and V-B mines).

Code of Federal Regulations, 2014 CFR

2014-07-01

... materials may be used in face areas. (b) Exposed surfaces on the intake side of stoppings constructed of... construction shall be solid. (c) Exposed surfaces on the fresh air side of seals constructed of combustible... other coatings with equivalent fire resistance. Stoppings constructed to phenolic foam blocks at least...

30 CFR 57.22218 - Seals and stoppings (III, V-A, and V-B mines).

Code of Federal Regulations, 2012 CFR

2012-07-01

... materials may be used in face areas. (b) Exposed surfaces on the intake side of stoppings constructed of... construction shall be solid. (c) Exposed surfaces on the fresh air side of seals constructed of combustible... other coatings with equivalent fire resistance. Stoppings constructed to phenolic foam blocks at least...

Thermal barrier coatings with (Al2O3-Y2O3)/(Pt or Pt-Au) composite bond coat and 8YSZ top coat on Ni-based superalloy

NASA Astrophysics Data System (ADS)

Yao, Junqi; He, Yedong; Wang, Deren; Peng, Hui; Guo, Hongbo; Gong, Shengkai

2013-12-01

Developing new bond coat has been acknowledged as an effective way to extend the service life of thermal barrier coating (TBC) during high temperature. In this study, novel thermal barrier coating system, which is composed with an (Al2O3-Y2O3)/(Pt or Pt-Au) composite bond coat and a YSZ top coat on Ni-based superalloy, has been prepared by magnetron sputtering and EB-PVD, respectively. It is demonstrated, from the cyclic oxidation tests in air at 1100 °C for 200 h, that the YSZ top coat and alloy substrate can be bonded together effectively by the (Al2O3-Y2O3)/(Pt or Pt-Au) composite coating, showing excellent resistance to oxidation, cracking and buckling. These beneficial results can be attributed to the sealing effect of such composite coating, by which the alloy substrate can be protected from oxidation and the interdiffusion between the bond coat and alloy substrate can be avoided; and the toughening effect of noble metals and composite structure of bond coat, by which the micro-cracks propagation can be inhibited and the stress in bond coat can be relaxed. This ceramic/noble metal composite coating can be a considerable structure which would has great application prospect in the TBC.

Friction and wear of sintered fiber-metal abradable seal materials

NASA Technical Reports Server (NTRS)

Bill, R. C.; Shiembob, L. T.

1977-01-01

Three abradable gas path seal material systems based on a sintered NiCrAlY fibermetal structure were evaluated under a range of wear conditions representative of those likely to be encountered in various knife-edge seal (labyrinth or shrouded turbine) applications. Conditions leading to undesirable wear of the rotating knife were identified and a model was proposed based on thermal effects arising under different rub conditions. It was found, and predicted by the model, that low incursion (plunge) rates tended to promote smearing of the low density sintered material with consequent wear to the knife-edge. Tradeoffs benefits between baseline 19 percent dense material, a similar material of increased density, and a self lubricating coating applied to the 19 percent material were identified based on relative rub tolerance and erosion resistance.

Rotary shaft sealing assembly

DOEpatents

Dietle, Lannie L; Schroeder, John E; Kalsi, Manmohan S; Alvarez, Patricio D

2013-08-13

A rotary shaft sealing assembly in which a first fluid is partitioned from a second fluid in a housing assembly having a rotary shaft located at least partially within. In one embodiment a lip seal is lubricated and flushed with a pressure-generating seal ring preferably having an angled diverting feature. The pressure-generating seal ring and a hydrodynamic seal may be used to define a lubricant-filled region with each of the seals having hydrodynamic inlets facing the lubricant-filled region. Another aspect of the sealing assembly is having a seal to contain pressurized lubricant while withstanding high rotary speeds. Another rotary shaft sealing assembly embodiment includes a lubricant supply providing a lubricant at an elevated pressure to a region between a lip seal and a hydrodynamic seal with a flow control regulating the flow of lubricant past the lip seal. The hydrodynamic seal may include an energizer element having a modulus of elasticity greater than the modulus of elasticity of a sealing lip of the hydrodynamic seal.

Rotary shaft sealing assembly

DOEpatents

Dietle, Lannie L.; Schroeder, John E.; Kalsi, Manmohan S.; Alvarez, Patricio D.

2010-09-21

A rotary shaft sealing assembly in which a first fluid is partitioned from a second fluid in a housing assembly having a rotary shaft located at least partially within. In one embodiment a lip seal is lubricated and flushed with a pressure-generating seal ring preferably having an angled diverting feature. The pressure-generating seal ring and a hydrodynamic seal may be used to define a lubricant-filled region with each of the seals having hydrodynamic inlets facing the lubricant-filled region. Another aspect of the sealing assembly is having a seal to contain pressurized lubricant while withstanding high rotary speeds. Another rotary shaft sealing assembly embodiment includes a lubricant supply providing a lubricant at an elevated pressure to a region between a lip seal and a hydrodynamic seal with a flow control regulating the flow of lubricant past the lip seal. The hydrodynamic seal may include an energizer element having a modulus of elasticity greater than the modulus of elasticity of a sealing lip of the hydrodynamic seal.

Potential contributions of asphalt and coal tar to black carbon quantification in urban dust, soils, and sediments

USGS Publications Warehouse

Yang, Y.; Mahler, B.J.; Van Metre, P.C.; Ligouis, B.; Werth, C.J.

2010-01-01

Measurements of black carbon (BC) using either chemical or thermal oxidation methods are generally thought to indicate the amount of char and/or soot present in a sample. In urban environments, however, asphalt and coal-tar particles worn from pavement are ubiquitous and, because of their pyrogenic origin, could contribute to measurements of BC. Here we explored the effect of the presence of asphalt and coal-tar particles on the quantification of BC in a range of urban environmental sample types, and evaluated biases in the different methods used for quantifying BC. Samples evaluated were pavement dust, residential and commercial area soils, lake sediments from a small urban watershed, and reference materials of asphalt and coal tar. Total BC was quantified using chemical treatment through acid dichromate (Cr2O7) oxidation and chemo-thermal oxidation at 375??C (CTO-375). BC species, including soot and char/charcoal, asphalt, and coal tar, were quantified with organic petrographic analysis. Comparison of results by the two oxidation methods and organic petrography indicates that both coal tar and asphalt contribute to BC quantified by Cr2O7 oxidation, and that coal tar contributes to BC quantified by CTO-375. These results are supported by treatment of asphalt and coal-tar reference samples with Cr2O7 oxidation and CTO-375. The reference asphalt is resistant to Cr2O7 oxidation but not to CTO-375, and the reference coal tar is resistant to both Cr2O7 oxidation and CTO-375. These results indicate that coal tar and/or asphalt can contribute to BC measurements in samples from urban areas using Cr2O7 oxidation or CTO-375, and caution is advised when interpreting BC measurements made with these methods. ?? 2010 Elsevier Ltd.

A comparison of physicochemical methods for the remediation of porous medium systems contaminated with tar

NASA Astrophysics Data System (ADS)

Hauswirth, Scott C.; Miller, Cass T.

2014-10-01

The remediation of former manufactured gas plant (FMGP) sites contaminated with tar DNAPLs (dense non-aqueous phase liquids) presents a significant challenge. The tars are viscous mixtures of thousands of individual compounds, including known and suspected carcinogens. This work investigates the use of combinations of mobilization, solubilization, and chemical oxidation approaches to remove and degrade tars and tar components in porous medium systems. Column experiments were conducted using several flushing solutions, including an alkaline-polymer (AP) solution containing NaOH and xanthan gum (XG), a surfactant-polymer (SP) solution containing Triton X-100 surfactant (TX100) and XG, an alkaline-surfactant-polymer (ASP) solution containing NaOH, TX100, and XG, and base-activated sodium persulfate both with and without added TX100. The effectiveness of the flushing solutions was assessed based on both removal of polycyclic aromatic hydrocarbon (PAH) mass and on the reduction of dissolved-phase PAH concentrations. SP flushes of 6.6 to 20.9 PV removed over 99% of residual PAH mass and reduced dissolved-phase concentrations by up to two orders of magnitude. ASP flushing efficiently removed 95-96% of residual PAH mass within about 2 PV, and significantly reduced dissolved-phase concentrations of several low molar mass compounds, including naphthalene, acenaphthene, fluorene, and phenanthrene. AP flushing removed a large portion of the residual tar (77%), but was considerably less effective than SP and ASP in terms of the effect on dissolved PAH concentrations. Persulfate was shown to oxidize tar components, primarily those with low molar mass, however, the overall degradation was relatively low (30-50% in columns with low initial tar saturations), and the impact on dissolved-phase concentrations was minimal.

Inboard seal mounting

DOEpatents

Hayes, John R.

1983-01-01

A regenerator assembly for a gas turbine engine has a hot side seal assembly formed in part by a cast metal engine block having a seal recess formed therein that is configured to supportingly receive ceramic support blocks including an inboard face thereon having a regenerator seal face bonded thereto. A pressurized leaf seal is interposed between the ceramic support block and the cast metal engine block to bias the seal wear face into sealing engagement with a hot side surface of a rotary regenerator matrix.

Triple acting radial seal

DOEpatents

Ebert, Todd A [West Palm Beach, FL; Carella, John A [Jupiter, FL

2012-03-13

A triple acting radial seal used as an interstage seal assembly in a gas turbine engine, where the seal assembly includes an interstage seal support extending from a stationary inner shroud of a vane ring, the interstage seal support includes a larger annular radial inward facing groove in which an outer annular floating seal assembly is secured for radial displacement, and the outer annular floating seal assembly includes a smaller annular radial inward facing groove in which an inner annular floating seal assembly is secured also for radial displacement. A compliant seal is secured to the inner annular floating seal assembly. The outer annular floating seal assembly encapsulates the inner annular floating seal assembly which is made from a very low alpha material in order to reduce thermal stress.

Security seal

DOEpatents

Gobeli, Garth W.

1985-01-01

Security for a package or verifying seal in plastic material is provided by a print seal with unique thermally produced imprints in the plastic. If tampering is attempted, the material is irreparably damaged and thus detectable. The pattern of the imprints, similar to "fingerprints" are recorded as a positive identification for the seal, and corresponding recordings made to allow comparison. The integrity of the seal is proved by the comparison of imprint identification records made by laser beam projection.

Fluorine uptake into the human enamel surface from fluoride-containing sealing materials during cariogenic pH cycling

NASA Astrophysics Data System (ADS)

Yasuhiro, Matsuda; Katsushi, Okuyama; Hiroko, Yamamoto; Hisanori, Komatsu; Masashi, Koka; Takahiro, Sato; Naoki, Hashimoto; Saiko, Oki; Chiharu, Kawamoto; Hidehiko, Sano

2015-04-01

To prevent the formation of caries and reduce dentin hypersensitivity, sealing materials, either with or without fluoride, are generally applied on the tooth in clinical practice. Application of fluoride-free sealing materials results in the formation of an acid-resistant layer on the tooth surface. On the other hand, fluoride-containing sealing materials might not only form an acid-resistant layer but could possibly further provide fluoride to enhance remineralization and reduce demineralization. In this study, the demineralization prevention ability and fluorine uptake rate in human enamel of fluoride-containing sealing materials ["MS coats F" (MSF)] and fluoride-free sealing materials ("hybrid coats 2" [HI]) were evaluated using an automatic pH cycling system. Each material was applied to the original tooth surface, the cut surfaces were covered with sticky wax, and the automatic pH-cycling system simulated daily acid changes (pH 6.8-4.5) occurring in the oral cavity for 4 weeks. Caries progression was analyzed using transverse microradiography (TMR) taken pre and post the 4 weeks of pH cycling. The fluorine and calcium distributions in the carious lesion in each specimen were evaluated using the proton-induced gamma emission (PIGE) and proton-induced X-ray (PIXE) techniques, respectively. TMR analysis showed that both MSF and HI had a caries-preventing effect after 4 weeks of pH cycling. PIGE/PIXE analysis demonstrated that only MSF resulted in fluoride uptake in the enamel surface. Therefore, MSF can help to form an acid-resistant layer and provide fluoride to the enamel surface. The presence of fluoride on the enamel surface suggested that MSF could prevent demineralization, even if the acid-resistant layer was removed, in clinical settings. The data obtained using the PIGE and PIXE techniques are useful for understanding the benefits of the use of a fluoride-containing sealing material for preventing caries.

Development of secondary chamber for tar cracking-improvement of wood pyrolysis performance in pre-vacuum chamber

NASA Astrophysics Data System (ADS)

Siahaan, S.; Homma, H.; Homma, H.

2018-02-01

Energy crisis and global warming, in other words, climate change are critical topics discussed in various parts of the world. Global warming primarily result from too much emission of carbon dioxide (CO2) in the atmosphere. To mitigate global warming, or climate change and improve electrification in rural areas, wood pyrolysis technology is developed in a laboratory scale, of which gases are directly applicable to the gas engine generator. Our laboratory has developed a prototype of wood pyrolysis plant with a pre-vacuum chamber. However, tar yield was around 40 wt% of feedstock. This research aims to reduce tar yield by secondary tar cracking. For the secondary tar cracking, a secondary pre-vacuum chamber is installed after primary pre-vacuum chamber. Gases generated in the primary pre-vacuum chamber are lead into the secondary chamber that is heated up to 1000 K. This paper reports performance of the secondary chamber for secondary tar cracking in homogeneous mode and heterogeneous mode with char.

The SSME seal test program: Leakage tests for helically-grooved seals

NASA Technical Reports Server (NTRS)

Childs, D. W.

1983-01-01

Helically grooved annular seal configurations were tested in highly turbulent flow to determine if reduced leakage and enhanced stability would result from the pumping action of the seal. It was found that: (1) leakage of a helically grooved seals decreases with running speed; (2) leakage reduction due to increased running speed is greater at lower values of R sub a; (3) an asymptote for leakage reduction is indicated with increasing running speed; (4) leakage is reduced by reducing the ridge (minimum) and average clearances; (5) leakage increases with increasing pitch angles and with increasing groove depth. Plain seals with smooth rotors and stators will leak more than a helically grooved seal. It was also found that plain seals with a rough rotor and a rough stator leak less than a properly designed helically grooved seal. A properly designed helically grooved seal consumes at least twice as much power as a conventional annular seal.

Seal dynamics on the Swedish west coast: Scenarios of competition as Baltic grey seal intrude on harbour seal territory

NASA Astrophysics Data System (ADS)

Svensson, Carl Johan

2012-07-01

The Kattegat-Skagerrak region on the Swedish west coast is home to an abundant harbour seal population (Phoca vitulina) and a small scattered grey seal population (Halichoerus grypus). In addition, grey seal from the growing population in the Baltic Sea frequently migrate into the Kattegat-Skagerrak. Harbour seals on the west coast of Sweden show relatively high population growth (approximately 9%) compared to the Baltic grey seal in ice-free habitats (approximately 6%), which, in theory, makes harbour seal the stronger competitor of the two in this region. However, incidents of disease in harbour seals that lower population growth are becoming more frequent. These epidemics are primarily caused by the Phocine Distemper Virus (PDV), and may reduce population size with up to 70%. This study models the average development under potential scenarios of competing harbour- and Baltic grey seal populations using Leslie matrices and the Lotka-Volterra model of inter-specific competition. The model is parameterised with previously published data, and resource overlap is incorporated through density dependent pup survival. Using numerical methods short- and long-term abundances are simulated under weak, moderate and strong competition and for different frequencies of PDV epidemics. Results show that the harbour seals are resilient to competition while exerting a negative effect on grey seal abundance under moderate to strong competition. Hence Baltic grey seal benefit from weaker levels of competition. Under moderate and strong competition grey seal abundance is a direct function of the PDV frequency as this reduces the competitive strength of harbour seals. Theoretically this means that higher frequencies of PDV or other pathogens epidemics could facilitate an expansion of Baltic grey seal into Kattegat-Skagerrak. Independent of interaction strength and frequency of epidemics the projected changes to abundances are slow (50-100 years), and even in exceedingly stable

Skew resisting hydrodynamic seal

DOEpatents

Conroy, William T.; Dietle, Lannie L.; Gobeli, Jeffrey D.; Kalsi, Manmohan S.

2001-01-01

A novel hydrodynamically lubricated compression type rotary seal that is suitable for lubricant retention and environmental exclusion. Particularly, the seal geometry ensures constraint of a hydrodynamic seal in a manner preventing skew-induced wear and provides adequate room within the seal gland to accommodate thermal expansion. The seal accommodates large as-manufactured variations in the coefficient of thermal expansion of the sealing material, provides a relatively stiff integral spring effect to minimize pressure-induced shuttling of the seal within the gland, and also maintains interfacial contact pressure within the dynamic sealing interface in an optimum range for efficient hydrodynamic lubrication and environment exclusion. The seal geometry also provides for complete support about the circumference of the seal to receive environmental pressure, as compared the interrupted character of seal support set forth in U.S. Pat. Nos. 5,873,576 and 6,036,192 and provides a hydrodynamic seal which is suitable for use with non-Newtonian lubricants.

Optical, Physical and Chemical Properties of Tar Balls Observed During the Yosemite Aerosol Characterization Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hand, Jenny L.; Malm, W. C.; Laskin, Alexander

2005-11-09

The Yosemite Aerosol Characterization Study of summer 2002 (YACS) occurred during an active fire season in the western U. S., and provided an opportunity to investigate many unresolved issues related to the radiative effects of biomass burning aerosols. Single particle analysis was performed on field collected aerosol samples using an array of electron microscopy techniques. Amorphous carbon spheres, or “tar balls”, were present in samples collected during episodes of high particle light scattering coefficients that occurred during the peak of a smoke/haze event. The highest concentrations of light-absorbing carbon from a dual-wavelength aethalometer (λ = 370 and 880 nm) occurredmore » during periods when the particles were predominantly tar balls, indicating they do absorb light in the UV and near-IR range of the solar spectrum. Closure experiments of mass concentrations and light scattering coefficients during periods dominated by tar balls did not require any distinct assumptions of organic carbon molecular weight correction factors, density, or refractive index compared to periods dominated by other types of organic carbon aerosols. Measurements of the hygroscopic behavior of tar balls using an environmental SEM indicate that tar balls do not exhibit deliquescence, but do uptake some water at high (~83 %) relative humidity. The ability of tar balls to efficiently scatter and absorb light, and to absorb water has important implications for their role in regional haze and climate fence.« less

Corrosion protective coating for metallic materials

DOEpatents

Buchheit, Rudolph G.; Martinez, Michael A.

1998-01-01

Corrosion protective coatings for metallic materials, particularly aluminum and aluminum alloys, produced with simple, low-cost equipment and materials other than toxic metals or metal salts, or metal cyanides. The metallic material is cleaned, degreased, and deoxidized, the surface is converted to a substantially alkaline condition, and the surface is chemically sealed with inorganic metal compounds.

Improving oxidation resistance and thermal insulation of thermal barrier coatings by intense pulsed electron beam irradiation

NASA Astrophysics Data System (ADS)

Mei, Xianxiu; Liu, Xiaofei; Wang, Cunxia; Wang, Younian; Dong, Chuang

2012-12-01

In this paper, intense pulsed electron beam was used for the irradiation treatment of 6-8% Y2O3-stablized ZrO2 thermal barrier coating prepared by electron beam-physical vapor deposition to achieve the "sealing" of columnar crystals, thus improving their thermal insulation properties and high temperature oxidation resistance. The electron beam parameters used were: pulse duration 200 μs, electron voltage 15 kV, energy density 3, 5, 8, 15, 20 J/cm2, and pulsed numbers 30. 1050 °C cyclic oxidation and static oxidation experiments were used for the research on oxidation resistance of the coatings. When the energy density of the electron beam was larger than 8 J/cm2, ZrO2 ceramic coating surface was fully re-melted and became smooth, dense and shiny. The coating changed into a smooth polycrystalline structure, thus achieving the "sealing" effect of the columnar crystals. After irradiations with the energy density of 8-15 J/cm2, the thermally grown oxide coating thickness decreased significantly in comparison with non-irradiated coatings, showing that the re-melted coating improved the oxidation resistance of the coatings. The results of thermal diffusivity test by laser flash method showed that the thermal diffusion rate of the irradiated coating was lower than that of the coating without irradiation treatment, and the thermal insulation performance of irradiated coating was improved.

Brucella Antibodies in Alaskan True Seals and Eared Seals-Two Different Stories.

PubMed

Nymo, Ingebjørg H; Rødven, Rolf; Beckmen, Kimberlee; Larsen, Anett K; Tryland, Morten; Quakenbush, Lori; Godfroid, Jacques

2018-01-01

Brucella pinnipedialis was first isolated from true seals in 1994 and from eared seals in 2008. Although few pathological findings have been associated with infection in true seals, reproductive pathology including abortions, and the isolation of the zoonotic strain type 27 have been documented in eared seals. In this study, a Brucella enzyme-linked immunosorbent assay (ELISA) and the Rose Bengal test (RBT) were initially compared for 206 serum samples and a discrepancy between the tests was found. Following removal of lipids from the serum samples, ELISA results were unaltered while the agreement between the tests was improved, indicating that serum lipids affected the initial RBT outcome. For the remaining screening, we used ELISA to investigate the presence of Brucella antibodies in sera of 231 eared and 1,412 true seals from Alaskan waters sampled between 1975 and 2011. In eared seals, Brucella antibodies were found in two Steller sea lions ( Eumetopias jubatus ) (2%) and none of the 107 Northern fur seals ( Callorhinus ursinus ). The low seroprevalence in eared seals indicate a low level of exposure or lack of susceptibility to infection. Alternatively, mortality due to the Brucella infection may remove seropositive animals from the population. Brucella antibodies were detected in all true seal species investigated; harbor seals ( Phoca vitulina ) (25%), spotted seals ( Phoca largha ) (19%), ribbon seals ( Histriophoca fasciata ) (16%), and ringed seals ( Pusa hispida hispida ) (14%). There was a low seroprevalence among pups, a higher seroprevalence among juveniles, and a subsequent decreasing probability of seropositivity with age in harbor seals. Similar patterns were present for the other true seal species; however, solid conclusions could not be made due to sample size. This pattern is in accordance with previous reports on B. pinnipedialis infections in true seals and may suggest environmental exposure to B. pinnipedialis at the juvenile stage, with a

Protective coating for alumina-silicon carbide whisker composites

DOEpatents

Tiegs, Terry N.

1989-01-01

Ceramic composites formed of an alumina matrix reinforced with silicon carbide whiskers homogenously dispersed therein are provided with a protective coating for preventing fracture strength degradation of the composite by oxidation during exposure to high temperatures in oxygen-containing atmospheres. The coating prevents oxidation of the silicon carbide whiskers within the matrix by sealing off the exterior of the matrix so as to prevent oxygen transport into the interior of the matrix. The coating is formed of mullite or mullite plus silicon oxide and alumina and is formed in place by heating the composite in air to a temperature greater than 1200.degree. C. This coating is less than about 100 microns thick and adequately protects the underlying composite from fracture strength degradation due to oxidation.

Corkscrew Seals: Grey Seal (Halichoerus grypus) Infanticide and Cannibalism May Indicate the Cause of Spiral Lacerations in Seals

PubMed Central

2016-01-01

Large numbers of dead seals with characteristic spiral lesions have been washing ashore around the North Atlantic over the past two decades. Interactions with ship propellers and shark predation have been suggested as the likely causal mechanisms. However, new evidence points towards a more likely candidate: grey seal predation. An adult male grey seal was observed and recorded catching, killing and eating five weaned grey seal pups over a period of one week on the Isle of May, Scotland. A further 9 carcasses found in the same area exhibited similar injuries. Post mortem analysis of lesions indicated the wound characteristics were similar to each other and in 12 of the 14 carcasses analysed, were indistinguishable from carcasses previously attributed to propeller interaction. We therefore propose that most of the seal carcasses displaying spiral lacerations in the UK are caused by grey seal predation. Cases in other locations should be re-evaluated using the scoring system presented here to identify whether grey seal predation is a major cause of mortality in phocid seals. PMID:27254025

Corkscrew Seals: Grey Seal (Halichoerus grypus) Infanticide and Cannibalism May Indicate the Cause of Spiral Lacerations in Seals.

PubMed

Brownlow, Andrew; Onoufriou, Joseph; Bishop, Amanda; Davison, Nicholas; Thompson, Dave

2016-01-01

Large numbers of dead seals with characteristic spiral lesions have been washing ashore around the North Atlantic over the past two decades. Interactions with ship propellers and shark predation have been suggested as the likely causal mechanisms. However, new evidence points towards a more likely candidate: grey seal predation. An adult male grey seal was observed and recorded catching, killing and eating five weaned grey seal pups over a period of one week on the Isle of May, Scotland. A further 9 carcasses found in the same area exhibited similar injuries. Post mortem analysis of lesions indicated the wound characteristics were similar to each other and in 12 of the 14 carcasses analysed, were indistinguishable from carcasses previously attributed to propeller interaction. We therefore propose that most of the seal carcasses displaying spiral lacerations in the UK are caused by grey seal predation. Cases in other locations should be re-evaluated using the scoring system presented here to identify whether grey seal predation is a major cause of mortality in phocid seals.

Fundamentals of fluid sealing

NASA Technical Reports Server (NTRS)

Zuk, J.

1976-01-01

The fundamentals of fluid sealing, including seal operating regimes, are discussed and the general fluid-flow equations for fluid sealing are developed. Seal performance parameters such as leakage and power loss are presented. Included in the discussion are the effects of geometry, surface deformations, rotation, and both laminar and turbulent flows. The concept of pressure balancing is presented, as are differences between liquid and gas sealing. Mechanisms of seal surface separation, fundamental friction and wear concepts applicable to seals, seal materials, and pressure-velocity (PV) criteria are discussed.

Fused Silica Surface Coating for a Flexible Silica Mat Insulation System

NASA Technical Reports Server (NTRS)

Rhodes, W. H.

1973-01-01

Fused silica insulation coatings have been developed for application to a flexible mat insulation system. Based on crystalline phase nucleation and growth kinetics, a 99+% SiO2 glass was selected as the base composition. A coating was developed that incorporated the high emissivity phase NiCr2O4 as a two phase coating with goals of high emittance and minimum change in thermal expansion. A second major coating classification has a plasma sprayed emittance coating over a sealed pure amorphous SiO2 layer. A third area of development centered on extremely thin amorphous SiO2 coatings deposited by chemical vapor deposition. The coating characterization studies presented are mechanical testing of thin specimens extracted from the coatings, cyclic arc exposures, and emittance measurements before and after arc exposures.

Comparative evaluation of topical calcipotriol versus coal tar and salicylic acid ointment in chronic plaque psoriasis.

PubMed

Singh, Preeti; Gupta, Surabhi; Abidi, Afroz; Krishna, Arvind

2013-08-01

Calcipotriol is a newer topical treatment option available for plaque psoriasis and coal tar being one of the oldest treatment and still in use. To evaluate and compare the differences in terms of efficacy, safety and relapse with Calcipotriol 0.005% (50 mcg/gm) and 6% coal tar and 3% salicylic ointment in patients with Plaque psoriasis. SETTING and Study conducted on 60 patients of plaque psoriasis, who attended the skin OPD in our hospital. The patients with mild to moderate plaque psoriasis were selected. 60 patients were enrolled for the study after obtaining informed consent. Subjects were asked to apply Calcipotriol 0.005% (50 mcg/gm) (Heximar Win care) twice a day on the right side plaques and on left side plaques, Petroleum jelly (Vaseline) in the morning and 6% coal tar and 3% salicylic ointment (Protar® Percos) at nighttime. PASI score was used to assess the reponse to therapy at 2nd, 4th, 6th and 8th week. After treatment subjects were observed for 6 weeks for any relapse. It was done by paired t-test and independent sample t-test. The results showed that statistically significant difference was seen in the mean percentage reduction of PASI score between both the groups, at all the assessment visits, 2, 4, 6, and 8 weeks, the mean percentage reduction at 2 weeks for calcipotriol being 21±12.06 and for coal tar being 13.44±11.19 (P=0.000), at 4 weeks for calcipotriol was 40±16.71 and for coal tar 25±99 (P=0.000), at 6 weeks for calcipotriol was 53.99+-22.43 and for coal tar 41±21.23 (P=0.002), at 8 weeks for calcipotriol was 62.73±24.04 and for coal tar was 51.53±23.27 (P=0.11). Relapse was seen in 5/60 (8.3%) of patients on calcipotriol treated side and 9/60 (15%) of patients with coal tar treated side. Thus it can be concluded that calcipotriol cream is more efficacious when compared with coal tar and does have a quick response. It is well tolerated and acceptable cosmetically.

Seroprevalence of Antibodies against Seal Influenza A(H10N7) Virus in Harbor Seals and Gray Seals from the Netherlands.

PubMed

Bodewes, Rogier; Rubio García, Ana; Brasseur, Sophie M; Sanchez Conteras, Guillermo J; van de Bildt, Marco W G; Koopmans, Marion P G; Osterhaus, Albert D M E; Kuiken, Thijs

2015-01-01

In the spring and summer 2014, an outbreak of seal influenza A(H10N7) virus infection occurred among harbor seals (Phoca vitulina) off the coasts of Sweden and Denmark. This virus subsequently spread to harbor seals off the coasts of Germany and the Netherlands. While thousands of seals were reported dead in Sweden, Denmark and Germany, only a limited number of seals were found dead in the Netherlands. To determine the extent of exposure of seals in the Netherlands to influenza A/H10N7 virus, we measured specific antibody titers in serum samples from live-captured seals and seals admitted for rehabilitation in the Netherlands by use of a hemagglutination inhibition assay and an ELISA. In harbor seals in 2015, antibodies against seal influenza A(H10N7) virus were detected in 41% (32 out of 78) pups, 10% (5 out of 52) weaners, and 58% (7 out of 12) subadults or adults. In gray seals (Halichoerus grypus) in 2015, specific antibodies were not found in the pups (n = 26), but in 26% (5 out of 19) of the older animals. These findings indicate that, despite apparent low mortality, infection with seal influenza A(H10N7) virus was geographically widespread and also occurred in grey seals.

Selected constituents in the smokes of U. S. commercial cigaretts: tar, nicotine, carbon monoxide and carbon dioxide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jenkins, R.A.; Quincy, R.B.; Guerin, M.R.

One hundred twenty-one brands of United States commercial cigarettes were analyzed for their deliveries of tar, nicotine, carbon monoxide, and carbon dioxide under standard analytical smoking conditions. The sample included both filter and nonfilter cigarettes. Comparisons of carbon monoxide deliveries over the range of observed tar deliveries indicated a very high correlation between CO and tar for filter cigarettes, but nonfilter cigarettes tended to produce much less CO than would have been predicted from their tar deliveries. Comparison of ORNL nicotine values for specific brands with those determined by the Federal Trade Commission yield no statistically significant differences between laboratories.more » 4 figures, 6 tables.« less

Indium sealing techniques.

NASA Technical Reports Server (NTRS)

Hochuli, U.; Haldemann, P.

1972-01-01

Gold films are used as an alloying flux to form 5-micron-thick indium film seals at temperatures below 300 C. Pyrex was sealed to quartz, ULE, CER-VIT, Irtran 2, Ge, GaAs, Invar, Kovar, Al, and Cu. The seals can also be used as current feedthroughs and graded seals.

Shaft seal system

DOEpatents

Kapich, Davorin D.

1985-01-01

A shaft seal system is disclosed for isolating two regions of different fluid mediums through which a rotatable shaft extends. The seal system includes a seal housing through which the shaft extends and which defines an annular land and an annular labyrinth both of which face on the shaft so that each establishes a corresponding fluid sealing annulus. A collection cavity is formed in communication with the annular sealing spaces, and fluids compatible with the fluids in each of the two regions to be isolated are introduced, respectively, into the annular sealing spaces and collected in the collection cavity from which the fluid mixture is removed and passed to a separator which separates the fluids and returns them to their respective annular sealing spaces in a recycling manner. In the illustrated embodiment, the isolated fluid mediums comprise a liquid region and a gas region. Gas is removed from the gas region and passed through a purifier and a gas pump operative to introduce the purified gas through the labyrinth sealing annulus to the collection cavity. After passing to the separator, the separated gas is passed through a dryer from which the dried gas is caused to pass through the labyrinth sealing annulus into the collection cavity independently of the purified gas so as to insure isolation of the gas region in the event of sealing gas pump malfunction.

Ligand-induced changes in 2-aminopurine fluorescence as a probe for small molecule binding to HIV-1 TAR RNA

PubMed Central

BRADRICK, THOMAS D.; MARINO, JOHN P.

2004-01-01

Replication of human immunodeficiency virus type 1 (HIV-1) is regulated in part through an interaction between the virally encoded trans-activator protein Tat and the trans-activator responsive region (TAR) of the viral RNA genome. Because TAR is highly conserved and its interaction with Tat is required for efficient viral replication, it has received much attention as an antiviral drug target. Here, we report a 2-aminopurine (2-AP) fluorescence-based assay for evaluating potential TAR inhibitors. Through selective incorporation of 2-AP within the bulge (C23 or U24) of a truncated form of the TAR sequence (Δ TAR-ap23 and Δ TAR-ap24), binding of argininamide, a 24-residue arginine-rich peptide derived from Tat, and Neomycin has been characterized using steady-state fluorescence. Binding of argininamide to the 2-AP ΔTAR constructs results in a four- to 11-fold increase in fluorescence intensity, thus providing a sensitive reporter of that interaction (KD ~ 1 mM). Similarly, binding of the Tat peptide results in an initial 14-fold increase in fluorescence (KD ~ 25 nM), but is then followed by a slight decrease that is attributed to an additional, lower-affinity association(s). Using the ΔTAR-ap23 and TAR-ap24 constructs, two classes of Neomycin binding sites are detected; the first molecule of antibiotic binds as a noncompetitive inhibitor of Tat/argininamide (KD ~ 200 nM), whereas the second, more weakly bound molecule(s) becomes associated in a presumably nonspecific manner (KD ~ 4 μM). Taken together, the results demonstrate that the 2-AP fluorescence-detected binding assays provide accurate and general methods for quantitatively assessing TAR interactions. PMID:15273324

PEO of pre-anodized Al-Si alloys: Corrosion properties and influence of sealings

NASA Astrophysics Data System (ADS)

Mohedano, M.; Matykina, E.; Arrabal, R.; Mingo, B.; Pardo, A.

2015-08-01

Voltage-controlled PEO coatings were developed on A356 aluminum alloys (gravity-cast and rheocast) with a pre-anodized layer. The influence of the alloy manufacturing process and the effect of Si-rich phase on the structure and composition of the oxide layers were evaluated using SEM, EDS and XRD. The pre-anodized oxide layer preserves the microstructure of the substrate due to the presence of secondary phases that have a different behavior relative to the matrix during anodizing. PEO coatings consisted of a mixture of α-Al2O3, γ-Al2O3 and mullite. The corrosion behavior and the effectiveness of different sealing techniques based on salts of nickel, cobalt, cerium and phosphonic acid were also studied. Post-treatments improved the hydrophobic properties of the coatings and showed a beneficial effect, significantly increasing the coating impedance and thereby reducing the susceptibility to corrosion.

X-38 Seal Development

NASA Technical Reports Server (NTRS)

Curry, Donald M.; Lewis, Ronald K.; Hagen, Jeffrey D.

2002-01-01

An X-38 Crew Return Vehicle Seal Development is presented. The contents include: 1) X-38 Crew Return Vehicle; 2) X-38 TPS Configuration; 3) X-38 Seal Locations; 4) X-38 Rudder/Fin Seal Assembly; 5) Baseline X-38 Rudder/Fin Seal Design; 6) Rudder/Fin Seal to Bracket Assembly; 7) X-38 Rudder/Fin Vertical Rub Surface Inconel-0.10 inches; 8) X-38 Rudder/Fin Seal Analysis; 9) Seal Analysis Model; and 10) Governing Differential Equations for Equilibrium Thermal Assumption. The X-38 Rudder/Fin Seal temperature and pressure properties are also given.

Pyrolysis of aseptic packages (tetrapak) in a laboratory screw type reactor and secondary thermal/catalytic tar decomposition.

PubMed

Haydary, J; Susa, D; Dudáš, J

2013-05-01

Pyrolysis of aseptic packages (tetrapak cartons) in a laboratory apparatus using a flow screw type reactor and a secondary catalytic reactor for tar cracking was studied. The pyrolysis experiments were realized at temperatures ranging from 650 °C to 850 °C aimed at maximizing of the amount of the gas product and reducing its tar content. Distribution of tetrapak into the product yields at different conditions was obtained. The presence of H2, CO, CH4, CO2 and light hydrocarbons, HCx, in the gas product was observed. The Aluminum foil was easily separated from the solid product. The rest part of char was characterized by proximate and elemental analysis and calorimetric measurements. The total organic carbon in the tar product was estimated by elemental analysis of tars. Two types of catalysts (dolomite and red clay marked AFRC) were used for catalytic thermal tar decomposition. Three series of experiments (without catalyst in a secondary cracking reactor, with dolomite and with AFRC) at temperatures of 650, 700, 750, 800 and 850 °C were carried out. Both types of catalysts have significantly affected the content of tars and other components in pyrolytic gases. The effect of catalyst on the tetrapack distribution into the product yield on the composition of gas and on the total organic carbon in the tar product is presented in this work. Copyright © 2013 Elsevier Ltd. All rights reserved.

Dynamic sealing principles

NASA Technical Reports Server (NTRS)

Zuk, J.

1976-01-01

The fundamental principles governing dynamic sealing operation are discussed. Different seals are described in terms of these principles. Despite the large variety of detailed construction, there appear to be some basic principles, or combinations of basic principles, by which all seals function, these are presented and discussed. Theoretical and practical considerations in the application of these principles are discussed. Advantages, disadvantages, limitations, and application examples of various conventional and special seals are presented. Fundamental equations governing liquid and gas flows in thin film seals, which enable leakage calculations to be made, are also presented. Concept of flow functions, application of Reynolds lubrication equation, and nonlubrication equation flow, friction and wear; and seal lubrication regimes are explained.

Demonstration of pharmaceutical tablet coating process by injection molding technology.

PubMed

Puri, Vibha; Brancazio, David; Harinath, Eranda; Martinez, Alexander R; Desai, Parind M; Jensen, Keith D; Chun, Jung-Hoon; Braatz, Richard D; Myerson, Allan S; Trout, Bernhardt L

2018-01-15

We demonstrate the coating of tablets using an injection molding (IM) process that has advantage of being solvent free and can provide precision coat features. The selected core tablets comprising 10% w/w griseofulvin were prepared by an integrated hot melt extrusion-injection molding (HME-IM) process. Coating trials were conducted on a vertical injection mold machine. Polyethylene glycol and polyethylene oxide based hot melt extruded coat compositions were used. Tablet coating process feasibility was successfully demonstrated using different coating mold designs (with both overlapping and non-overlapping coatings at the weld) and coat thicknesses of 150 and 300 μm. The resultant coated tablets had acceptable appearance, seal at the weld, and immediate drug release profile (with an acceptable lag time). Since IM is a continuous process, this study opens opportunities to develop HME-IM continuous processes for transforming powder to coated tablets. Copyright © 2017 Elsevier B.V. All rights reserved.

Identification of amino acids that promote specific and rigid TAR RNA-tat protein complex formation.

PubMed

Edwards, Thomas E; Robinson, Bruce H; Sigurdsson, Snorri Th

2005-03-01

The Tat protein and the transactivation responsive (TAR) RNA form an essential complex in the HIV lifecycle, and mutations in the basic region of the Tat protein alter this RNA-protein molecular recognition. Here, EPR spectroscopy was used to identify amino acids, flanking an essential arginine of the Tat protein, which contribute to specific and rigid TAR-Tat complex formation by monitoring changes in the mobility of nitroxide spin-labeled TAR RNA nucleotides upon binding. Arginine to lysine N-terminal mutations did not affect TAR RNA interfacial dynamics. In contrast, C-terminal point mutations, R56 in particular, affected the mobility of nucleotides U23 and U38, which are involved in a base-triple interaction in the complex. This report highlights the role of dynamics in specific molecular complex formation and demonstrates the ability of EPR spectroscopy to study interfacial dynamics of macromolecular complexes.

Turbine blade platform seal

DOEpatents

Zagar, Thomas W.; Schiavo, Anthony L.

2001-01-01

A rotating blade group 90 for a turbo-machine having an improved device for sealing the gap 110 between the edges 112,114 of adjacent blade platforms 96,104. The gap 110 between adjacent blades 92,100 is sealed by a seal pin 20 its central portion 110 and by a seal plate 58,60 at each of the front 54 and rear 56 portions. The seal plates 58,60 are inserted into corresponding grooves 62,64 formed in the adjacent edges 112,114 of adjoining blades 92,100 and held in place by end plates 40,42. The end of the seal plates 58,60 may be chamfered 78,80 to improve the seal against the end plate 40,42. The seal pin 20 provides the required damping between the blades 92,100 and the seal plates 58,60 provide improved sealing effectiveness.

Fuel cell manifold sealing system

DOEpatents

Grevstad, Paul E.; Johnson, Carl K.; Mientek, Anthony P.

1980-01-01

A manifold-to-stack seal and sealing method for fuel cell stacks. This seal system solves the problem of maintaining a low leak rate manifold seal as the fuel cell stack undergoes compressive creep. The seal system eliminates the problem of the manifold-to-stack seal sliding against the rough stack surface as the stack becomes shorter because of cell creep, which relative motion destroys the seal. The seal system described herein utilizes a polymer seal frame firmly clamped between the manifold and the stack such that the seal frame moves with the stack. Thus, as the stack creeps, the seal frame creeps with it, and there is no sliding at the rough, tough to seal, stack-to-seal frame interface. Here the sliding is on a smooth easy to seal location between the seal frame and the manifold.

Machine-smoking studies of cigarette filter color to estimate tar yield by visual assessment and through the use of a colorimeter.

PubMed

Morton, Michael J; Williams, David L; Hjorth, Heather B; Smith, Jennifer H

2010-04-01

This paper explores using the intensity of the stain on the end of the filter ("filter color") as a vehicle for estimating cigarette tar yield, both by instrument reading of the filter color and by visual comparison to a template. The correlation of machine-measured tar yield to filter color measured with a colorimeter was reasonably strong and was relatively unaffected by different puff volumes or different tobacco moistures. However, the correlation of filter color to machine-measured nicotine yield was affected by the moisture content of the cigarette. Filter color, as measured by a colorimeter, was generally comparable to filter extraction of either nicotine or solanesol in its correlation to machine-smoked tar yields. It was found that the color of the tar stain changes over time. Panelists could generally correctly order the filters from machine-smoked cigarettes by tar yield using the intensity of the tar stain. However, there was considerable variation in the panelist-to-panelist tar yield estimates. The wide person-to-person variation in tar yield estimates, and other factors discussed in the text could severely limit the usefulness and practicality of this approach for visually estimating the tar yield of machine-smoked cigarettes. Copyright 2009 Elsevier Inc. All rights reserved.

High pressure mechanical seal

NASA Technical Reports Server (NTRS)

Babel, Henry W. (Inventor); Anderson, Raymond H. (Inventor)

1996-01-01

A relatively impervious mechanical seal is formed between the outer surface of a tube and the inside surface of a mechanical fitting of a high pressure fluid or hydraulic system by applying a very thin soft metal layer onto the outer surface of the hard metal tube and/or inner surface of the hard metal fitting. The thickness of such thin metal layer is independent of the size of the tube and/or fittings. Many metals and alloys of those metals exhibit the requisite softness, including silver, gold, tin, platinum, indium, rhodium and cadmium. Suitably, the coating is about 0.0025 millimeters (0.10 mils) in thickness. After compression, the tube and fitting combination exhibits very low leak rates on the order or 10.sup.-8 cubic centimeters per second or less as measured using the Helium leak test.

Turbine with radial acting seal

DOEpatents

Eng, Darryl S; Ebert, Todd A

2016-11-22

A floating brush seal in a rim cavity of a turbine in a gas turbine engine, where the floating brush seal includes a seal holder in which the floating brush seal floats, and a expandable seal that fits within two radial extending seal slots that maintains a seal with radial displacement of the floating brush seal and the seal holder.

Tamper-indicating seal

DOEpatents

Fiarman, S.; Degen, M.F.; Peters, H.F.

1982-08-13

There is disclosed a tamper-indicating seal that permits in the field inspection and detection of tampering. Said seal comprises a shrinkable tube having a visible pattern of markings which is shrunk over th item to be sealed, and a second transparent tube, having a second visible marking pattern, which is shrunk over the item and the first tube. The relationship between the first and second set of markings produces a pattern so that the seal may not be removed without detection. The seal is particularly applicable to UF/sub 6/ cylinder valves.

A case-control study of asphalt and tar exposure and lung cancer in minorities.

PubMed

McClean, Michael D; Kelsey, Karl T; Sison, Jennette D; Quesenberry, Charles P; Wrensch, Margaret R; Wiencke, John K

2011-11-01

Considerable controversy surrounds the carcinogenic potential of asphalt and tar. Since minority individuals may have had relatively high historical exposures, we investigated asphalt and tar exposure and lung cancer risk among African Americans and Latino Americans. We conducted a case-control study of lung cancer among African Americans and Latino Americans in the San Francisco Bay area (422 cases, 894 controls). A questionnaire was used to obtain detailed work histories and exposure information. Self-reported exposure to asphalt and tar as well as other factors (e.g., smoking, automobile exhaust, and asbestos) were evaluated as predictors of lung cancer risk. Potential effect modification by cytochrome P450 (CYP) 1A1 was also explored. Self-reported duration of exposure to asphalt and tar was associated with a statistically significant excess risk of lung cancer in the overall population (OR: 1.11, 95% CI: 1.01-1.22), evaluating risk per year of exposure. Years of exposure to automobile exhaust (OR: 1.02, 95% CI: 1.00-1.05) and asbestos (OR: 1.04, 95% CI: 1.02-1.06) were also associated with statistically significant elevations in risk. In Latino Americans, the lung cancer risks associated with polycyclic aromatic hydrocarbon-related exposures were consistently higher in the CYP1A1 wild-type subjects as compared to the variant genotype subjects, and the interaction was statistically significant for smoking and the CYP1A1 M2 polymorphism (P-value(interaction) = 0.02). These data are consistent with the literature suggesting that exposure to asphalt and tar may increase risk of lung cancer. However, it was not possible to separate the effects and asphalt and tar in this study. Copyright © 2011 Wiley Periodicals, Inc.

A Case-Control Study of Asphalt and Tar Exposure and Lung Cancer in Minorities

PubMed Central

McClean, Michael D.; Kelsey, Karl T.; Sison, Jennette D; Quesenberry, Charles P; Wrensch, Margaret R; Wiencke, John K.

2011-01-01

Objectives Considerable controversy surrounds the carcinogenic potential of asphalt and tar. Since minority individuals may have had relatively high historical exposures, we investigated asphalt and tar exposure and lung cancer risk among African Americans and Latino Americans. Methods We conducted a case-control study of lung cancer among African Americans and Latino Americans in the San Francisco Bay area (422 cases, 894 controls). A questionnaire was used to obtain detailed work histories and exposure information. Self-reported exposure to asphalt and tar as well as other factors (eg. smoking, automobile exhaust, and asbestos) were evaluated as predictors of lung cancer risk. Potential effect modification by cytochrome P450 (CYP) 1A1 was also explored. Results Self-reported duration of exposure to asphalt and tar was associated with a statistically significant excess risk of lung cancer in the overall population (OR: 1.11, 95%CI: 1.01–1.22), evaluating risk per year of exposure. Years of exposure to automobile exhaust (OR: 1.02, 95%CI: 1.00–1.05) and asbestos (OR: 1.04, 95%CI: 1.02–1.06) were also associated with statistically significant elevations in risk. In Latino Americans, the lung cancer risks associated with polycyclic aromatic hydrocarbon-related exposures were consistently higher in the CYP1A1 wildtype subjects as compared to the variant genotype subjects, and the interaction was statistically significant for smoking and the CYP1A1 M2 polymorphism (p-valueinteraction=0.02). Conclusions These data are consistent with the literature suggesting that exposure to asphalt and tar may increase risk of lung cancer. However, it was not possible to separate the effects and asphalt and tar in this study. PMID:21882217

The linear relationship between cigarette tar and nicotine yields: regulatory implications for smoke constituent ratios.

PubMed

St Charles, F K; Cook, C J; Clayton, P M

2011-02-01

Cigarette smoke analyte yields are often expressed as ratios relative to tar or nicotine yields, usually to compare different products or to estimate human uptake of smoke in relation to nicotine uptake measurements. The method, however, can lead to distorted interpretations, especially in the case of ratios from ultra-low tar yield cigarettes. In brief, as tar yields decrease below the 5–6 mg per cigarette range, the tar-to-nicotine ratio (TNR) decreases rapidly in a non-linear fashion. If, however, the nicotine yield, rather than the ratio, is plotted versus the tar yield, the non-linearity disappears and a straight line is obtained, with a slight positive intercept for nicotine on the ordinate. Unlike the ratio, the slope appears to depend only on the concentration of the nicotine in the blend and does not appear to vary with smoking parameters such as puff volume, puff interval or length smoked or with cigarette design parameters such as length, circumference or the amount of filtration or filter ventilation. Therefore, such a slope is analogous to the TNR although, unlike that ratio, it is invariant. Even more simply, the concentration of the nicotine in the blend, at least for American blend-style cigarettes, provides a similar index.

Design-Based Peptidomimetic Ligand Discovery to Target HIV TAR RNA Using Comparative Analysis of Different Docking Methods.

PubMed

Fu, Junjie; Xia, Amy; Dai, Yao; Qi, Xin

2016-01-01

Discovering molecules capable of binding to HIV trans-activation responsive region (TAR) RNA thereby disrupting its interaction with Tat protein is an attractive strategy for developing novel antiviral drugs. Computational docking is considered as a useful tool for predicting binding affinity and conducting virtual screening. Although great progress in predicting protein-ligand interactions has been achieved in the past few decades, modeling RNA-ligand interactions is still largely unexplored due to the highly flexible nature of RNA. In this work, we performed molecular docking study with HIV TAR RNA using previously identified cyclic peptide L22 and its analogues with varying affinities toward HIV-1 TAR RNA. Furthermore, sarcosine scan was conducted to generate derivatives of CGP64222, a peptide-peptoid hybrid with inhibitory activity on Tat/TAR RNA interaction. Each compound was docked using CDOCKER, Surflex-Dock and FlexiDock to compare the effectiveness of each method. It was found that FlexiDock energy values correlated well with the experimental Kd values and could be used to predict the affinity of the ligands toward HIV-1 TAR RNA with a superior accuracy. Our results based on comparative analysis of different docking methods in RNA-ligand modeling will facilitate the structure-based discovery of HIV TAR RNA ligands for antiviral therapy.

Corrosion protective coating for metallic materials

DOEpatents

Buchheit, R.G.; Martinez, M.A.

1998-05-26

Corrosion protective coatings for metallic materials, particularly aluminum and aluminum alloys, produced with simple, low-cost equipment and materials other than toxic metals or metal salts, or metal cyanides is disclosed. The metallic material is cleaned, degreased, and deoxidized, the surface is converted to a substantially alkaline condition, and the surface is chemically sealed with inorganic metal compounds. 1 fig.

Nozzle seal

DOEpatents

Herman, Richard Frederick

1977-10-25

In an illustrative embodiment of the invention, a nuclear reactor pressure vessel, having an internal hoop from which the heated coolant emerges from the reactor core and passes through to the reactor outlet nozzles, is provided with sealing members operatively disposed between the outlet nozzle and the hoop. The sealing members are biased against the pressure vessel and the hoop and are connected by a leak restraining member establishing a leak-proof condition between the inlet and outlet coolants in the region about the outlet nozzle. Furthermore, the flexible responsiveness of the seal assures that the seal will not structurally couple the hoop to the pressure vessel.

Nuclear reactor sealing system

DOEpatents

McEdwards, James A.

1983-01-01

A liquid metal-cooled nuclear reactor sealing system. The nuclear reactor includes a vessel sealed at its upper end by a closure head. The closure head comprises at least two components, one of which is rotatable; and the two components define an annulus therebetween. The sealing system includes at least a first and second inflatable seal disposed in series in an upper portion of the annulus. The system further includes a dip seal extending into a body of insulation located adjacent a bottom portion of the closure head. The dip seal comprises a trough formed by a lower portion of one of the components, and a seal blade pendently supported from the other component and extending downwardly into the trough. A body of liquid metal is contained in the trough which submerges a portion of the seal blade. The seal blade is provided with at least one aperture located above the body of liquid metal for providing fluid communication between the annulus intermediate the dip seal and the inflatable seals, and a body of cover gas located inside the vessel. There also is provided means for introducing a purge gas into the annulus intermediate the inflatable seals and the seal blade. The purge gas is introduced in an amount sufficient to substantially reduce diffusion of radioactive cover gas or sodium vapor up to the inflatable seals. The purge gas mixes with the cover gas in the reactor vessel where it can be withdrawn from the vessel for treatment and recycle to the vessel.

Identification of sources of tar balls deposited along the Goa coast, India, using fingerprinting techniques.

PubMed

Suneel, V; Vethamony, P; Zakaria, M P; Naik, B G; Prasad, K V S R

2013-05-15

Deposition of tar balls along the coast of Goa, India is a common phenomenon during the southwest monsoon. Representative tar ball samples collected from various beaches of Goa and one Bombay High (BH) crude oil sample were subjected to fingerprint analysis based on diagnostic ratios of n-alkane, biomarkers of pentacyclic tri-terpanes and compound specific stable carbon isotope (δ¹³C) analysis to confirm the source. The results were compared with the published data of Middle East Crude Oil (MECO) and South East Asian Crude Oil (SEACO). The results revealed that the tar balls were from tanker-wash derived spills. The study also confirmed that the source is not the BH, but SEACO. The present study suggests that the biomarkers of alkanes and hopanes coupled with stable carbon isotope analysis act as a powerful tool for tracing the source of tar balls, particularly when the source specific biomarkers fail to distinguish the source. Copyright © 2013 Elsevier Ltd. All rights reserved.

Compliant seal development

NASA Technical Reports Server (NTRS)

Hendricks, Robert C.

1993-01-01

The compliant metallic seal combines the noncontact feature of the labyrinth seal, the low leakage of a mechanical seal, and the compliant nature of the brush seal. It consists of several thin metallic elements or leaves mounted within a ring which is press fit into the housing, and in form, sort of resembles a lip seal sections wiping the shaft. A second set of overlapping cover leaves are placed on top of the shaft riding leaves which reduces leakage and provides stiffness. The leaves can be straight or angle cut. The shaft riding fingers are designed with mismatched curvature to provide lift off similar to the Rayleigh lift pads in mechanical seals with leading edge clearances nearly twice those of the trailing edge as as shown by Fleming to be optimal for gas flows in convergent seal passages. Leading edge clearances range from 300 to 500 microinches. Balance pockets beneath the leaves provide fluid film feed to the 'Rayleigh lift' surface and the proper balance ratio (mechanical seal) when combined with the static pressure and film pressure. The leaves flex in the radial direction and accommodate thermomechanical behavior as well as axial motion and angular misalignment. In the static mode, there is a net closing force on the leaves. The seals were tested to 70 psi at speeds to 16,000 rpm or surface speeds to 330 fps and temperatures from ambient to 440 F. A slow cycle through the rig critical at 10,000 rpm induced a radial vibration response of 0.004 to 0.005 inch were accommodated by the seal. Preliminary performance data are encouraging demonstrating hydrodynamic liftoff and noncontacting operation at pressure and speeds typical of gas turbine engines. The leakage performance data are significantly better than commercial labyrinth and brush seals which should be expected as this design incorporates the features of the low leakage face or mechanical seal along with the flexibility of the brush configuration.

Compliant seal development

NASA Astrophysics Data System (ADS)

Hendricks, Robert C.

1993-10-01

The compliant metallic seal combines the noncontact feature of the labyrinth seal, the low leakage of a mechanical seal, and the compliant nature of the brush seal. It consists of several thin metallic elements or leaves mounted within a ring which is press fit into the housing, and in form, sort of resembles a lip seal sections wiping the shaft. A second set of overlapping cover leaves are placed on top of the shaft riding leaves which reduces leakage and provides stiffness. The leaves can be straight or angle cut. The shaft riding fingers are designed with mismatched curvature to provide lift off similar to the Rayleigh lift pads in mechanical seals with leading edge clearances nearly twice those of the trailing edge as as shown by Fleming to be optimal for gas flows in convergent seal passages. Leading edge clearances range from 300 to 500 microinches. Balance pockets beneath the leaves provide fluid film feed to the 'Rayleigh lift' surface and the proper balance ratio (mechanical seal) when combined with the static pressure and film pressure. The leaves flex in the radial direction and accommodate thermomechanical behavior as well as axial motion and angular misalignment. In the static mode, there is a net closing force on the leaves. The seals were tested to 70 psi at speeds to 16,000 rpm or surface speeds to 330 fps and temperatures from ambient to 440 F. A slow cycle through the rig critical at 10,000 rpm induced a radial vibration response of 0.004 to 0.005 inch were accommodated by the seal. Preliminary performance data are encouraging demonstrating hydrodynamic liftoff and noncontacting operation at pressure and speeds typical of gas turbine engines. The leakage performance data are significantly better than commercial labyrinth and brush seals which should be expected as this design incorporates the features of the low leakage face or mechanical seal along with the flexibility of the brush configuration.

Self-acting shaft seals

NASA Technical Reports Server (NTRS)

Ludwig, L. P.

1978-01-01

Self-acting seals are described in detail. The mathematical models for obtaining a seal force balance and the equilibrium operating film thickness are outlined. Particular attention is given to primary ring response (seal vibration) to rotating seat face runout. This response analysis reveals three different vibration models with secondary seal friction being an important parameter. Leakage flow inlet pressure drop and affects of axisymmetric sealing face deformations are discussed. Experimental data on self-acting face seals operating under simulated gas turbine conditions are given. Also a spiral groove seal design operated to 244 m/sec (800 ft/sec) is described.

Damped flexible seal

DOEpatents

DuBois, Neil J.; Amaral, Antonio M.

1992-10-27

A damped flexible seal assembly for a torpedo isolates the tailcone thereof rom vibrational energy present in the drive shaft assembly. A pair of outside flanges, each of which include an inwardly facing groove and an O-ring constrained therein, provide a watertight seal against the outer non-rotating surface of the drive shaft assembly. An inside flange includes an outwardly-facing groove and an O-ring constrained therein, and provides a watertight seal against the inner surface of the tail cone. Two cast-in-place elastomeric seals provide a watertight seal between the flanges and further provide a damping barrier between the outside flanges and the inside flanges for damping vibrational energy present in the drive shaft assembly before the energy can reach the tailcone through the seal assembly.

Ubiquitous tar balls with a California-source signature on the shorelines of Prince William Sound, Alaska

USGS Publications Warehouse

Kvenvolden, K.A.; Hostettler, F.D.; Carlson, P.R.; Rapp, J.B.; Threlkeld, C.N.; Warden, A.

1995-01-01

Although the shorelines of Prince William Sound still bear traces of the 1989 Exxon Valdez oil spill, most of the flattened tar balls that can be found today on these shorelines are not residues of Exxon Valdez oil. Instead, the carbon-isotopic and hydrocarbon-biomarker signatures of 61 tar ball samples, collected from shorelines throughout the northern and western parts of the sound, are all remarkably similar and have characteristics consistent with those of oil products that originated from the Monterey Formation source rocks of California. The carbon-isotopic compositions of the tar balls are all closely grouped (??13CPDB = -23.7 ?? 0.2???), within the range found in crude oils from those rocks, but are distinct from isotopic compositions of 28 samples of residues from the Exxon Valdez oil spill (??13CPDB = -29.4 ?? 0.1???). Likewise, values for selected biomarker ratios in the tar balls are all similar but distinct from values of residues from the 1989 oil spill. Carbon-isotopic and biomarker signatures generally relate the tar balls to oil products used in Alaska before ???1970 for construction and pavements. How these tar balls with such similar geochemical characteristics became so widely dispersed throughout the northern and western parts of the sound is not known with certainty, but the great 1964 Alaska earthquake was undoubtedly an important trigger, causing spills from ruptured storage facilities of California-sourced asphalt and fuel oil into Prince William Sound.

Microplastic and tar pollution on three Canary Islands beaches: An annual study.

PubMed

Herrera, A; Asensio, M; Martínez, I; Santana, A; Packard, T; Gómez, M

2018-04-01

Marine debris accumulation was analyzed from three exposed beaches of the Canary Islands (Lambra, Famara and Las Canteras). Large microplastics (1-5mm), mesoplastics (5-25mm) and tar pollution were assessed twice a month for a year. There was great spatial and temporal variability in the Canary Island coastal pollution. Seasonal patterns differed at each location, marine debris concentration depended mainly of local-scale wind and wave conditions. The most polluted beach was Lambra, a remote beach infrequently visited. The types of debris found were mainly preproduction resin pellets, plastic fragments and tar, evidencing that pollution was not of local origin, but it cames from the open sea. The levels of pollution were similar to those of highly industrialized and contaminated regions. This study corroborates that the Canary Islands are an area of accumulation of microplastics and tar rafted from the North Atlantic Ocean by the southward flowing Canary Current. Copyright © 2017 Elsevier Ltd. All rights reserved.

Numerical simulation of vortex pyrolysis reactors for condensable tar production from biomass

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, R.S.; Bellan, J.

1998-08-01

A numerical study is performed in order to evaluate the performance and optimal operating conditions of vortex pyrolysis reactors used for condensable tar production from biomass. A detailed mathematical model of porous biomass particle pyrolysis is coupled with a compressible Reynolds stress transport model for the turbulent reactor swirling flow. An initial evaluation of particle dimensionality effects is made through comparisons of single- (1D) and multi-dimensional particle simulations and reveals that the 1D particle model results in conservative estimates for total pyrolysis conversion times and tar collection. The observed deviations are due predominantly to geometry effects while directional effects frommore » thermal conductivity and permeability variations are relatively small. Rapid ablative particle heating rates are attributed to a mechanical fragmentation of the biomass particles that is modeled using a critical porosity for matrix breakup. Optimal thermal conditions for tar production are observed for 900 K. Effects of biomass identity, particle size distribution, and reactor geometry and scale are discussed.« less

Some developments on ceramic-to-metal and glass-ceramics-to-metal seals and related studies

NASA Astrophysics Data System (ADS)

Kothiyal, G. P.; Goswami, M.; Shrikhande, V. K.

2008-05-01

Seals and coatings based on ceramics and glass-ceramics find numerous applications in different disciplines of science and technology including space, accelerators, nuclear energy, chemical industry. Ceramic-to-metal (CM) seals based on conventional design (using brazing alloys) and glass-ceramics have been prepared. While Ag-Cu brazing alloy has been used in conventional CM seal, we have employed lithium zinc silicate (LZS) and lithium aluminum silicate (LAS) glass-ceramics for glass-ceramics-to-metal (GCM) seals. LZS glass-ceramics based on two different compositions; (a) LZSL composition (wt.%)- Li2O: 12.65, ZnO: 1.85, SiO2: 74.4, Al2O3: 3.8, K2O: 2.95, P2O5: 3.15, and B2O3: 1.2 (low ZnO) and (b) LZSH composition (wt.%)- Li2O: 8.9, ZnO: 24.03, SiO2: 53.7, Na2O: 5.42, P2O5: 2.95, and B2O3: 5.0 (high ZnO) were prepared with desired sealing characteristics for matched type seals. In addition, (wt.%) 12.6Li2O-71.7SiO2-5.1Al2O3-4.9K2O-3.2B2O3-2.5P2O5 (LAS-GC) was investigated for compressive type of seal. LZS glass-ceramics-to-Cu as well as SS-321 seals were found to withstand a vacuum of 10-6 Torr with leak rate 10-9 Torr. 1/s and LAS GC-to-SS304 seal showed high pressure endurance of 12000psi. In order to understand the mechanism of sealing, glass-ceramics-to-metal interface study has also been carried out.

DeepMirTar: a deep-learning approach for predicting human miRNA targets.

PubMed

Wen, Ming; Cong, Peisheng; Zhang, Zhimin; Lu, Hongmei; Li, Tonghua

2018-06-01

MicroRNAs (miRNAs) are small noncoding RNAs that function in RNA silencing and post-transcriptional regulation of gene expression by targeting messenger RNAs (mRNAs). Because the underlying mechanisms associated with miRNA binding to mRNA are not fully understood, a major challenge of miRNA studies involves the identification of miRNA-target sites on mRNA. In silico prediction of miRNA-target sites can expedite costly and time-consuming experimental work by providing the most promising miRNA-target-site candidates. In this study, we reported the design and implementation of DeepMirTar, a deep-learning-based approach for accurately predicting human miRNA targets at the site level. The predicted miRNA-target sites are those having canonical or non-canonical seed, and features, including high-level expert-designed, low-level expert-designed, and raw-data-level, were used to represent the miRNA-target site. Comparison with other state-of-the-art machine-learning methods and existing miRNA-target-prediction tools indicated that DeepMirTar improved overall predictive performance. DeepMirTar is freely available at https://github.com/Bjoux2/DeepMirTar_SdA. lith@tongji.edu.cn, hongmeilu@csu.edu.cn. Supplementary data are available at Bioinformatics online.

Exposure to runoff from coal-tar-sealed pavement induces genotoxicity and impairment of DNA repair capacity in the RTL-W1 fish liver cell line

USGS Publications Warehouse

Kienzler, Aude; Mahler, Barbara J.; Van Metre, Peter C.; Schweigert, Nathalie; Devaux, Alain; Bony, Sylvie

2015-01-01

Coal-tar-based (CTB) sealcoat, frequently applied to parking lots and driveways in North America, contains elevated concentrations of polycyclic aromatic hydrocarbons (PAHs) and related compounds. The RTL-W1 fish liver cell line was used to investigate two endpoints (genotoxicity and DNA-repair-capacity impairment) associated with exposure to runoff from asphalt pavement with CTB sealcoat or with an asphalt-based sealcoat hypothesized to contain about 7% CTB sealcoat (AS-blend). Genotoxic potential was assessed by the Formamido pyrimidine glycosylase (Fpg)-modified comet assay for 1:10 and 1:100 dilutions of runoff samples collected from 5 h to 36 d following sealcoat application. DNA-repair capacity was assessed by the base excision repair comet assay for 1:10 dilution of samples collected 26 h and 36 d following application. Both assays were run with and without co-exposure to ultraviolet-A radiation (UVA). With co-exposure to UVA, genotoxic effects were significant for both dilutions of CTB runoff for three of four sample times, and for some samples of AS-blend runoff. Base excision repair was significantly impaired for CTB runoff both with and without UVA exposure, and for AS-blend runoff only in the absence of UVA. This study is the first to investigate the effects of exposure to the complex mixture of chemicals in coal tar on DNA repair capacity. The results indicate that co-exposure to runoff from CT-sealcoated pavement and UVA as much as a month after sealcoat application has the potential to cause genotoxicity and impair DNA repair capacity.

Development of improved coating for advanced carbon-carbon components

NASA Technical Reports Server (NTRS)

Yamaki, Y. R.; Brown, J. J.

1984-01-01

Reaction sintered silicon nitride (RSSN) was studied as a substitute coating material on the carbon-carbon material (RCC) presently used as a heat shield on the space shuttle, and on advanced carbon-carbon (ACC), a later development. On RCC, RSSN showed potential in a 538 C (1000 F) screening test in which silicon carbide coated material exhibits its highest oxidation rate; RSSN afforded less protection to ACC because of a larger thermal expansion mismatch. Organosilicon densification and metallic silicon sealing methods were studied as means of further increasing the oxidation resistance of the coating, and some improvement was noted when these methods were employed.

Human immunodeficiency virus type 1 LTR TATA and TAR region sequences required for transcriptional regulation.

PubMed Central

Garcia, J A; Harrich, D; Soultanakis, E; Wu, F; Mitsuyasu, R; Gaynor, R B

1989-01-01

The human immunodeficiency virus (HIV) type 1 LTR is regulated at the transcriptional level by both cellular and viral proteins. Using HeLa cell extracts, multiple regions of the HIV LTR were found to serve as binding sites for cellular proteins. An untranslated region binding protein UBP-1 has been purified and fractions containing this protein bind to both the TAR and TATA regions. To investigate the role of cellular proteins binding to both the TATA and TAR regions and their potential interaction with other HIV DNA binding proteins, oligonucleotide-directed mutagenesis of both these regions was performed followed by DNase I footprinting and transient expression assays. In the TATA region, two direct repeats TC/AAGC/AT/AGCTGC surround the TATA sequence. Mutagenesis of both of these direct repeats or of the TATA sequence interrupted binding over the TATA region on the coding strand, but only a mutation of the TATA sequence affected in vivo assays for tat-activation. In addition to TAR serving as the site of binding of cellular proteins, RNA transcribed from TAR is capable of forming a stable stem-loop structure. To determine the relative importance of DNA binding proteins as compared to secondary structure, oligonucleotide-directed mutations in the TAR region were studied. Local mutations that disrupted either the stem or loop structure were defective in gene expression. However, compensatory mutations which restored base pairing in the stem resulted in complete tat-activation. This indicated a significant role for the stem-loop structure in HIV gene expression. To determine the role of TAR binding proteins, mutations were constructed which extensively changed the primary structure of the TAR region, yet left stem base pairing, stem energy and the loop sequence intact. These mutations resulted in decreased protein binding to TAR DNA and defects in tat-activation, and revealed factor binding specifically to the loop DNA sequence. Further mutagenesis which inverted

Method for sealing an oxygen transport membrane assembly

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gonzalez, Javier E.; Grant, Arthur F.

An improved method of sealing a ceramic part to a solid part made of ceramic, metal, cermet or a ceramic coated metal is provided. The improved method includes placing a bond agent comprising an Al 2O 3 and SiO 2 based glass-ceramic material and organic binder material on adjoining surfaces of the ceramic part and the solid part. The assembly is heated to a first target temperature that removes or dissolves the organic binder material from the bond agent and the assembly is subjected to a second induction heating step at a temperature ramp rate of between about 100.degree. C.more » and 200.degree. C. per minute to temperatures where the glass-ceramic material flows and wets the interface between adjoining surfaces. The assembly is rapidly cooled at a cooling rate of about 140.degree. C. per minute or more to induce nucleation and re-crystallization of the glass-ceramic material to form a dense, durable and gas-tight seal.« less

Numerical Investigation of the Effect of Radial Lip Seal Geometry on Sealing Performance

NASA Astrophysics Data System (ADS)

Tok, G.; Parlar, Z.; Temiz, V.

2018-01-01

Sealing elements are often needed in industry and especially in machine design. With the change and development of machine technology from day to day, sealing elements show continuous development and change in parallel with these developments. Many factors influence the performance of the sealing elements such as shaft surface roughness, radial force, lip geometry etc. In addition, the radial lip seals must have a certain pre-load and interference in order to provide a good sealing. This also affects the friction torque. Researchers are developing new seal designs to reduce friction losses in mechanical systems. In the presented study, the effect of the lip seal geometry on sealing performance will be examined numerically. The numerical model created for this purpose will be verified with experimental data firstly. In the numerical model, shaft and seal will be modeled as hyper-elastic in 2D and 3D. NBR (Nitrile Butadiene Rubber) as seal material will be analyzed for the rotating shaft state at constant speed by applying a uniform radial force.

Energy efficient face seal

NASA Technical Reports Server (NTRS)

Sehnal, J.; Sedy, J.; Etsion, I.; Zobens, A.

1982-01-01

Torque, face temperature, leakage, and wear of a flat face seal were compared with three coned face seals at pressures up to 2758 kPa and speeds up to 8000 rpm. Axial movement of the mating seal parts was recorded by a digital data acquisition system. The coning of the tungsten carbide primary ring ranged from .51 micro-m to 5.6 micro-m. The torque of the coned face seal balanced to 76.3% was an average 42% lower, the leakage eleven times higher, than that of the standard flat face seal. The reduction of the balance of the coned face seal to 51.3% resulted by decreasing the torque by an additional 44% and increasing leakage 12 to 230 times, depending on the seal shaft speed. No measurable wear was observed on the face of the coned seals.

SSME Seal Test Program: Test results for sawtooth pattern damper seal

NASA Technical Reports Server (NTRS)

Childs, D. W.

1986-01-01

Direct and transverse force coefficients for 11, sawtooth-pattern, and damper-seal configurations were examined. The designation damper seal uses a deliberately roughened stator and smooth rotor to increase the net damping force developed by a seal. The designation sawtooth-pattern refers to a stator roughness pattern. The sawtooth pattern yields axial grooves in the stator which are interrupted by spacer elements which act as flow constrictions or dams. All seals use the same smooth rotor and have the same, constant, minimum clearance. The stators examined the consequences of changes in the following design parameters: (1) axial-groove depth; (2) number of teeth: (3) number of sawtooth sections; (4) number of spacer elements; (5) dam width; (6) axially aligned sawtooth sections versus axially-staggered sawtooth sections; and (7) groove geometry. It is found that none of the sawtooth-pattern seal performs as well as the best round-hole-pattern seal. Maximum damping configurations for the sawtooth and round-hole-pattern stators have comparable stiffness performance. Several of the sawtooth pattern stators outperformed the best round-hole pattern seal.

Collapsable seal member

DOEpatents

Sherrell, Dennis L.

1990-01-01

A hollow, collapsable seal member normally disposed in a natural expanded state offering fail-safe pressure sealing against a seating surface and adapted to be evacuated by a vacuum force for collapsing the seal member to disengage the same from said seating surface.

Circumferential shaft seal

NASA Technical Reports Server (NTRS)

Ludwig, L. P. (Inventor)

1981-01-01

A circumferential shaft seal comprising two sealing rings held to a rotating shaft by means of a surrounding elastomeric band is disclosed. The rings are segmented and are of a rigid sealing material such as carbon or a polyimide and graphite fiber composite.

Collapsable seal member

DOEpatents

Sherrell, D.L.

1983-12-08

A hollow, collapsable seal member normally disposed in a natural expanded state offering fail-safe pressure sealing against a seating surface and adapted to be evacuated by a vacuum force for collapsing the seal member to disengage the same from said seating surface.

Seals Flow Code Development 1993

NASA Technical Reports Server (NTRS)

Liang, Anita D. (Compiler); Hendricks, Robert C. (Compiler)

1994-01-01

Seals Workshop of 1993 code releases include SPIRALI for spiral grooved cylindrical and face seal configurations; IFACE for face seals with pockets, steps, tapers, turbulence, and cavitation; GFACE for gas face seals with 'lift pad' configurations; and SCISEAL, a CFD code for research and design of seals of cylindrical configuration. GUI (graphical user interface) and code usage was discussed with hands on usage of the codes, discussions, comparisons, and industry feedback. Other highlights for the Seals Workshop-93 include environmental and customer driven seal requirements; 'what's coming'; and brush seal developments including flow visualization, numerical analysis, bench testing, T-700 engine testing, tribological pairing and ceramic configurations, and cryogenic and hot gas facility brush seal results. Also discussed are seals for hypersonic engines and dynamic results for spiral groove and smooth annular seals.

Upgrading producer gas quality from rubber wood gasification in a radio frequency tar thermocatalytic treatment reactor.

PubMed

Anis, Samsudin; Zainal, Z A

2013-12-01

This study focused on improving the producer gas quality using radio frequency (RF) tar thermocatalytic treatment reactor. The producer gas containing tar, particles and water was directly passed at a particular flow rate into the RF reactor at various temperatures for catalytic and thermal treatments. Thermal treatment generates higher heating value of 5.76 MJ Nm(-3) at 1200°C. Catalytic treatments using both dolomite and Y-zeolite provide high tar and particles conversion efficiencies of about 97% on average. The result also showed that light poly-aromatic hydrocarbons especially naphthalene and aromatic compounds particularly benzene and toluene were still found even at higher reaction temperatures. Low energy intensive RF tar thermocatalytic treatment was found to be effective for upgrading the producer gas quality to meet the end user requirements and increasing its energy content. Copyright © 2013 Elsevier Ltd. All rights reserved.

Determination of the conformational ensemble of the TAR RNA by X-ray scattering interferometry

PubMed Central

Walker, Peter

2017-01-01

Abstract The conformational ensembles of structured RNA's are crucial for biological function, but they remain difficult to elucidate experimentally. We demonstrate with HIV-1 TAR RNA that X-ray scattering interferometry (XSI) can be used to determine RNA conformational ensembles. X-ray scattering interferometry (XSI) is based on site-specifically labeling RNA with pairs of heavy atom probes, and precisely measuring the distribution of inter-probe distances that arise from a heterogeneous mixture of RNA solution structures. We show that the XSI-based model of the TAR RNA ensemble closely resembles an independent model derived from NMR-RDC data. Further, we show how the TAR RNA ensemble changes shape at different salt concentrations. Finally, we demonstrate that a single hybrid model of the TAR RNA ensemble simultaneously fits both the XSI and NMR-RDC data set and show that XSI can be combined with NMR-RDC to further improve the quality of the determined ensemble. The results suggest that XSI-RNA will be a powerful approach for characterizing the solution conformational ensembles of RNAs and RNA-protein complexes under diverse solution conditions. PMID:28108663

Determination of the conformational ensemble of the TAR RNA by X-ray scattering interferometry.

PubMed

Shi, Xuesong; Walker, Peter; Harbury, Pehr B; Herschlag, Daniel

2017-05-05

The conformational ensembles of structured RNA's are crucial for biological function, but they remain difficult to elucidate experimentally. We demonstrate with HIV-1 TAR RNA that X-ray scattering interferometry (XSI) can be used to determine RNA conformational ensembles. X-ray scattering interferometry (XSI) is based on site-specifically labeling RNA with pairs of heavy atom probes, and precisely measuring the distribution of inter-probe distances that arise from a heterogeneous mixture of RNA solution structures. We show that the XSI-based model of the TAR RNA ensemble closely resembles an independent model derived from NMR-RDC data. Further, we show how the TAR RNA ensemble changes shape at different salt concentrations. Finally, we demonstrate that a single hybrid model of the TAR RNA ensemble simultaneously fits both the XSI and NMR-RDC data set and show that XSI can be combined with NMR-RDC to further improve the quality of the determined ensemble. The results suggest that XSI-RNA will be a powerful approach for characterizing the solution conformational ensembles of RNAs and RNA-protein complexes under diverse solution conditions. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

High pressure mechanical seal

NASA Technical Reports Server (NTRS)

Babel, Henry W. (Inventor); Fuson, Phillip L. (Inventor); Chickles, Colin D. (Inventor); Jones, Cherie A. (Inventor); Anderson, Raymond H. (Inventor)

1995-01-01

A relatively impervious mechanical seal is formed between the outer surface of a tube and the inside surface of a mechanical fitting of a high pressure fluid or hydraulic system by applying a very thin soft metal layer onto the outer surface of the hard metal tube and/or inner surface of the hard metal fitting, prior to swaging the fitting onto the tube. The thickness of such thin metal layer is independent of the size of the tube and/or fittings. Many metals and alloys of those metals exhibit the requisite softness, including silver, gold, nickel, tin, platinum, indium, rhodium and cadmium. Suitably, the coating is about 0.0025 millimeters (0.10 mils) in thickness. After swaging, the tube and fitting combination exhibits very low leak rates on the order or 10.sup.-8 cubic centimeters per second or less as meaured using the Helium leak test.

Transmission seal development

NASA Technical Reports Server (NTRS)

Brien, M.

1977-01-01

An experimental evaluation was performed on a high-speed (72.9 m/s, 14,349 ft/min) transmission seal of the synergistic type. During testing of the seal, oil leakage occurred at positive bearing cavity pressures. Modifications were made in an attempt to eliminate the leakage but none were completely successful. Leakage appears to be the result of questionable positioning of the sealing elements resulting in inadequate shaft contact by the oil side sealing element. This condition may be related to the nonsymmetrical shape of the elastomeric retainer and to dimensional changes caused by swelling of the elastomeric retainer from exposure to the sealed fluid. Indications of a speed dependent leakage characteristic were also observed.

Foil Face Seal Testing

NASA Technical Reports Server (NTRS)

Munson, John

2009-01-01

In the seal literature you can find many attempts by various researchers to adapt film riding seals to the gas turbine engine. None have been successful, potential distortion of the sealing faces is the primary reason. There is a film riding device that does accommodate distortion and is in service in aircraft applications, namely the foil bearing. More specifically a foil thrust bearing. These are not intended to be seals, and they do not accommodate large axial movement between shaft & static structure. By combining the 2 a unique type of face seal has been created. It functions like a normal face seal. The foil thrust bearing replaces the normal primary sealing surface. The compliance of the foil bearing allows the foils to track distortion of the mating seal ring. The foil seal has several perceived advantages over existing hydrodynamic designs, enumerated in the chart. Materials and design methodology needed for this application already exist. Also the load capacity requirements for the foil bearing are low since it only needs to support itself and overcome friction forces at the antirotation keys.

Circumferential shaft seal

NASA Technical Reports Server (NTRS)

Ludwig, L. P. (Inventor)

1980-01-01

A circumferential shaft seal is described which comprises two sealing rings held to a rotating shaft by means of a surrounding elastomeric band. The rings are segmented and are of a rigid sealing material such as carbon or a polyimide and graphite fiber composite.

Thin film application device and method for coating small aperture vacuum vessels

DOEpatents

Walters, Dean R; Este, Grantley O

2015-01-27

A device and method for coating an inside surface of a vessel is provided. In one embodiment, a coating device comprises a power supply and a diode in electrical communication with the power supply, wherein electrodes comprising the diode reside completely within the vessel. The method comprises reversibly sealing electrodes in a vessel, sputtering elemental metal or metal compound on the surface while maintaining the surface in a controlled atmosphere.

SSME seal test program: Test results for hole-pattern damper seals

NASA Technical Reports Server (NTRS)

Childs, D. W.

1985-01-01

The results consisting of direct and transverse force coefficients are presented for thirteen, hole-pattern, damper-seal configurations. The designation damper seal refers to a seal which uses a deliberately roughened stator nd smooth rotor, to increase the net damping force developed by a seal. The designation hole-pattern refers to a stator roughness pattern which is developed by a pattern of round holes while are milled into the stator. All seals tested use the same smooth rotor and have the same constant minimum clearance. The seal tests examined the following major design options: (1) hole-area density, i.e., the proportion of stator surface area consumed by holes; and (2) hole depth, particularly the ratio of hole depth to minimum clearance. In addition, limited data were taken to examine the influence of in-line versus staggered hole patterns and flat-bottomed versus spherical-bottomed holes.

In-situ phosphatizing coatings for aerospace, OEM and coil coating applications

NASA Astrophysics Data System (ADS)

Neuder, Heather Aurelia

The current metal coating process is a multi-step process. The surface is cleaned, primered, dried and then painted. The process is labor intensive and time consuming. The wash primer is a conversion coating, which prepares metal surface for better paint adhesion. The wash primers currently used often contain hexavalent chromium (Cr6+), which seals the pores in the conversion coating. The presence of hexavalent chromium, a known carcinogen, and volatile organic compounds (VOCs) make waste disposal expensive and pose dangers to workers. The novel technique of in-situ phosphatizing coating (ISPC) is a single-step, chrome-free alternative to the present coating practice. Formulation of an ISPC involves predispersal of an in-situ phosphatizing reagent (ISPR) into the paint system to form a stable formulation. The ISPR reacts with the metal surface and bonds with the paint film simultaneously, which eliminates the need for a conversion coating. In acid catalyzed paint systems, such as polyester-melamine paints, the ISPR also catalyzes cross-linking reactions between the melamine and the polyester polyols. ISPCs are formulated using commercially available coating systems including: polyester-melamine, two-component epoxy, polyurethane and high-hydroxy content polyester-melamine coil coating. The ISPCs are applied to metal substrates and their performances are evaluated using electrochemical, thermal and standard American Society for Testing and Materials (ASTM) testing methods. In addition, ISPCs were designed and formulated based on: (1) phosphate chemistry, (2) polymer chemistry, (3) sol-gel chemistry, and (4) the ion-exchange principle. Organo-functionalized silanes, which serve as excellent coupling and dispersion agents, are incorporated into the optimized ISPC formula and evaluated using standard ASTM testing methods and electrochemical spectroscopy. Also, an ion-exchange pigment, which leads to better adhesion by forming a mixed metal silicate surface, is

SULFUR TOLERANT CATALYSTS FOR BIOMASS TAR REMOVAL - PHASE I

EPA Science Inventory

In this Small Business Innovation Research (SBIR) project, NexTech Materials proposes a catalytic reforming approach to remove waste tar from gasified biomass on nickel-based catalysts. Biomass gasification is a potential renewable route to producing electricity, liquid fue...

Influence of the presence of PAHs and coal tar on naphthalene sorption in soils

NASA Astrophysics Data System (ADS)

Bayard, Rémy; Barna, Ligia; Mahjoub, Borhane; Gourdon, Rémy

2000-11-01

The mobility of the most water-soluble polynuclear aromatic hydrocarbons (PAHs) such as naphthalene in contaminated soils from manufactured gas plant (MGP) sites or other similar sites is influenced not only by the naturally occurring soil organic matter (SOM) but also, and in many cases mostly, by the nature and concentration of coal tar xenobiotic organic matter (XOM) and other PAH molecules present in the medium under various physical states. The objective of the present study was to quantify the effects of these factors using batch experiments, in order to simulate naphthalene transport in soil-tar-water systems using column experiments. Naphthalene sorption was studied in the presence of (i) solid coal tar particles, (ii) phenanthrene supplied as pure crystals, in the aqueous solution or already sorbed onto the soil, (iii) fluoranthene as pure crystals, and (iv) an aqueous solution of organic molecules extracted from a liquid tar. All experiments were conducted under abiotic conditions using short naphthalene/sorbent contact times of 24-60 h. Although these tests do not reflect true equilibrium conditions which usually take more time to establish, they were used to segregate relatively rapid sorption phenomena ("pseudo equilibrium") from slow sorption and other aging phenomena. For longer contact times, published data have shown that experimental biases due to progressive changes in the characteristics of the soil and the solution may drastically modify the affinity of the solutes for the soil. Slow diffusion in the microporosity and in dense organic phases may also become significant over the long term, along with some irreversible aging phenomena which have not been addressed in this work. Results showed that PAHs had no effect on naphthalene sorption when present in the aqueous solution or as pure crystals, due to their low solubility in water. Adsorbed phenanthrene was found to reduce naphthalene adsorption only when present at relatively high

Canister, Sealing Method And Composition For Sealing A Borehole

DOEpatents

Brown, Donald W.; Wagh, Arun S.

2005-06-28

Method and composition for sealing a borehole. A chemically bonded phosphate ceramic sealant for sealing, stabilizing, or plugging boreholes is prepared by combining an oxide or hydroxide and a phosphate with water to form slurry. The slurry is introduced into the borehole where the seal, stabilization or plug is desired, and then allowed to set up to form the high strength, minimally porous sealant, which binds strongly to itself and to underground formations, steel and ceramics.

Laterally Translating Seal Carrier For A Drilling Mud Motor Sealed Bearing Assembly

DOEpatents

Dietle, Lannie

1993-03-23

A sealing and lubrication assembly for rotating shafts intended for operation in an abrasive environment and wherein the rotary shaft may have lateral translation or excursion during its rotation. A housing receives the rotary shaft in bearing supporting relation and defines a lubricant chamber about the shaft. A seal carrier is movably positioned about the rotary shaft and has non-rotatable articulating or laterally translating relation with the housing. A high pressure rotary shaft seal is supported by the seal carrier and maintains bearing and sealing engagement with the rotary shaft during its lateral translation or excursion. The seal carrier is hydraulic force balanced and thus is not subject to pressure induced loads that might otherwise interfere with its articulation or lateral translation.

Hexavalent Chrome Free Coatings for Electronics; Electromagnetic Interference (EMI) Shielding Effectiveness (SE)

NASA Technical Reports Server (NTRS)

Kessel, Kurt R.

2014-01-01

The purpose of this testing is to determine the suitability of trivalent chromium conversion coatings that meet the requirements of MIL-DTL-5541, Type II, for use in applications where high-frequency electrical performance is important. This project will evaluate the ability of coated aluminum to form adequate EMI seals. Testing will assess performance of the trivalent chromium coatings against the known control hexavalent chromium MIL-DTL-5541 Type I Class 3 before and after they have been exposed to a set of environmental conditions. Performance will be assessed by evaluating shielding effectiveness (SE) test data from a variety of test samples comprised of different aluminum types and/or conversion coatings.

46 CFR Table II to Part 150 - Grouping of Cargoes

Code of Federal Regulations, 2010 CFR

2010-10-01

... solutions Clay slurry Corn syrup Dextrose solution 2,4-Dichlorophenoxyacetic acid, Diethanolamine salt... Coal tar, high temperature Coal tar pitch Decahydronaphthalene Degummed C9 (DOW) Diphenyl, Diphenyl... Gas, high pour Heartcut distillate Linseed Lubricating Mineral Mineral seal Motor Neatsfoot...

46 CFR Table II to Part 150 - Grouping of Cargoes

Code of Federal Regulations, 2011 CFR

2011-10-01

... solutions Clay slurry Corn syrup Dextrose solution 2,4-Dichlorophenoxyacetic acid, Diethanolamine salt... Coal tar, high temperature Coal tar pitch Decahydronaphthalene Degummed C9 (DOW) Diphenyl, Diphenyl... Gas, high pour Heartcut distillate Linseed Lubricating Mineral Mineral seal Motor Neatsfoot...

46 CFR Table II to Part 150 - Grouping of Cargoes

Code of Federal Regulations, 2012 CFR

2012-10-01

... solutions Clay slurry Corn syrup Dextrose solution 2,4-Dichlorophenoxyacetic acid, Diethanolamine salt... Coal tar, high temperature Coal tar pitch Decahydronaphthalene Degummed C9 (DOW) Diphenyl, Diphenyl... Gas, high pour Heartcut distillate Linseed Lubricating Mineral Mineral seal Motor Neatsfoot...

Resilient Flexible Pressure-Activated Seal

NASA Technical Reports Server (NTRS)

Steinetz, Bruce M. (Inventor); Dunlap, Patrick H., Jr. (Inventor)

2009-01-01

A resilient, flexible, pressure-activated, high-temperature seal is adapted to be interposed between high and low pressure regions to provide sealing between opposing surfaces of adjacent relatively movable structures. The seal comprises at least one C-shaped sheet element. The C-shaped element design enables the seal to be pressure-activated to provide a radially outward biasing force, responsive to a seal-activating pressure differential acting across the seal thereby increasing resiliency. A centrally-located, resilient core structure provides load bearing and insulating properties. In an exemplary embodiment where at least two seal elements are used, each layer has a cutout slot pattern and the remaining strip material pattern. The slots provide flexibility to the seal, enabling the seal to be manually contoured to seal around corners and curves. The strip material of each layer covers the slots in each adjacent layer to minimize leakage through the slots. Attached barrier strips can block interface leakage between the seal and the opposing surfaces.

Design guide for helicopter transmission seals

NASA Technical Reports Server (NTRS)

Hayden, T. S.; Keller, C. H., Jr.

1974-01-01

A detailed approach for the selection and design of seals for helicopter transmissions is presented. There are two major types of seals presently being used and they are lip type seals and mechanical type seals. Lip type seals can be divided in conventional lip seals and hydrodynamic lip seals. Conventional lip seals can be used for slow-speed, low-pressure, low-temperature sealing. Hydrodynamic lip seals although they are as pressure and temperature limited as conventional lip seals, can operate at a higher speed. Mechanical types seals are comprised of face seals and circumferential seals. Face seals are capable of high speed, high pressure, and high temperature. Circumferential seals can be used in high-speed and high-temperature applications, but will leak excessively at moderate pressures. The performance goals of transmission seals are a life that is at least equal to the scheduled overhaul interval of the gearbox component and a leakage rate of near zero.

Exposure to runoff from coal-tar-sealed pavement induces genotoxicity and impairment of DNA repair capacity in the RTL-W1 fish liver cell line.

PubMed

Kienzler, Aude; Mahler, Barbara J; Van Metre, Peter C; Schweigert, Nathalie; Devaux, Alain; Bony, Sylvie

2015-07-01

Coal-tar-based (CTB) sealcoat, frequently applied to parking lots and driveways in North America, contains elevated concentrations of polycyclic aromatic hydrocarbons (PAHs) and related compounds. The RTL-W1 fish liver cell line was used to investigate two endpoints (genotoxicity and DNA-repair-capacity impairment) associated with exposure to runoff from asphalt pavement with CTB sealcoat or with an asphalt-based sealcoat hypothesized to contain about 7% CTB sealcoat (AS-blend). Genotoxic potential was assessed by the Formamido pyrimidine glycosylase (Fpg)-modified comet assay for 1:10 and 1:100 dilutions of runoff samples collected from 5 h to 36 d following sealcoat application. DNA-repair capacity was assessed by the base excision repair comet assay for 1:10 dilution of samples collected 26 h and 36 d following application. Both assays were run with and without co-exposure to ultraviolet-A radiation (UVA). With co-exposure to UVA, genotoxic effects were significant for both dilutions of CTB runoff for three of four sample times, and for some samples of AS-blend runoff. Base excision repair was significantly impaired for CTB runoff both with and without UVA exposure, and for AS-blend runoff only in the absence of UVA. This study is the first to investigate the effects of exposure to the complex mixture of chemicals in coal tar on DNA repair capacity. The results indicate that co-exposure to runoff from CT-sealcoated pavement and UVA as much as a month after sealcoat application has the potential to cause genotoxicity and impair DNA repair capacity. Copyright © 2015 Elsevier B.V. All rights reserved.

An implantable centrifugal blood pump with a recirculating purge system (Cool-Seal system).

PubMed

Yamazaki, K; Litwak, P; Tagusari, O; Mori, T; Kono, K; Kameneva, M; Watach, M; Gordon, L; Miyagishima, M; Tomioka, J; Umezu, M; Outa, E; Antaki, J F; Kormos, R L; Koyanagi, H; Griffith, B P

1998-06-01

A compact centrifugal blood pump has been developed as an implantable left ventricular assist system. The impeller diameter is 40 mm, and pump dimensions are 55 x 64 mm. This first prototype, fabricated from titanium alloy, resulted in a pump weight of 400 g including a brushless DC motor. The weight of a second prototype pump was reduced to 280 g. The entire blood contacting surface is coated with diamond like carbon (DLC) to improve blood compatibility. Flow rates of over 7 L/min against 100 mm Hg pressure at 2,500 rpm with 9 W total power consumption have been measured. A newly designed mechanical seal with a recirculating purge system (Cool-Seal) is used for the shaft seal. In this seal system, the seal temperature is kept under 40 degrees C to prevent heat denaturation of blood proteins. Purge fluid also cools the pump motor coil and journal bearing. Purge fluid is continuously purified and sterilized by an ultrafiltration unit which is incorporated in the paracorporeal drive console. In vitro experiments with bovine blood demonstrated an acceptably low hemolysis rate (normalized index of hemolysis = 0.005 +/- 0.002 g/100 L). In vivo experiments are currently ongoing using calves. Via left thoracotomy, left ventricular (LV) apex descending aorta bypass was performed utilizing an expanded polytetrafluoroethylene (ePTFE) vascular graft with the pump placed in the left thoracic cavity. In 2 in vivo experiments, the pump flow rate was maintained at 5-9 L/min, and pump power consumption remained stable at 9-10 W. All plasma free Hb levels were measured at less than 15 mg/dl. The seal system has demonstrated good seal capability with negligible purge fluid consumption (<0.5 ml/day). In both calves, the pumps demonstrated trouble free continuous function over 6 month (200 days and 222 days).

33 CFR 165.927 - Safety Zone; St. Louis River, Duluth/Interlake Tar Remediation Site, Duluth, MN.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Safety Zone; St. Louis River, Duluth/Interlake Tar Remediation Site, Duluth, MN. 165.927 Section 165.927 Navigation and Navigable... Coast Guard District § 165.927 Safety Zone; St. Louis River, Duluth/Interlake Tar Remediation Site...

Contamination control in hybrid microelectronic modules. Part 2: Selection and evaluation of coating materials

NASA Technical Reports Server (NTRS)

Himmel, R. P.

1975-01-01

The selection, test, and evaluation of organic coating materials for contamination control in hybrid circuits is reported. The coatings were evaluated to determine their suitability for use as a conformal coating over the hybrid microcircuit (including chips and wire bonds) inside a hermetically sealed package. Evaluations included ease of coating application and repair and effect on thin film and thick film resistors, beam leads, wire bonds, transistor chips, and capacitor chips. The coatings were also tested for such properties as insulation resistance, voltage breakdown strength, and capability of immobilizing loose particles inside the packages. The selected coatings were found to be electrically, mechanically, and chemically compatible with all components and materials normally used in hybrid microcircuits.

PAH volatilization following application of coal-tar-based pavement sealant

USGS Publications Warehouse

Van Metre, Peter C.; Majewski, Michael S.; Mahler, Barbara J.; Foreman, William T.; Braun, Christopher L.; Wilson, Jennifer T.; Burbank, Teresa L.

2012-01-01

Coal-tar-based pavement sealants, a major source of PAHs to urban water bodies, have recently been identified as a source of volatile PAHs to the atmosphere. We tracked the volatilization of PAHs for 1 year after application of a coal-tar-based pavement sealant by measuring gas-phase PAH concentrations above the pavement surface and solid-phase PAH concentrations in sealant scraped from the surface. Gas-phase concentrations at two heights (0.03 and 1.28 m) and wind speed were used to estimate volatilization flux. The sum of the concentrations of eight frequently detected PAHs (ΣPAH8) in the 0.03-m sample 1.6 h after application (297,000 ng m-3) was about 5000 times greater than that previously reported for the same height above unsealed parking lots (66 ng m-3). Flux at 1.6 h after application was estimated at 45,000 μg m-2 h-1 and decreased rapidly during the 45 days after application to 160 μg m-2 h-1. Loss of PAHs from the adhered sealant also was rapid, with about a 50% decrease in solid-phase ΣPAH8 concentration over the 45 days after application. There was general agreement, given the uncertainties, in the estimated mass of ΣPAH8 lost to the atmosphere on the basis of air sampling (2–3 g m-2) and adhered sealant sampling (6 g m-2) during the first 16 days after application, translating to a loss to the atmosphere of one-quarter to one-half of the PAHs in the sealcoat product. Combining the estimated mass of ΣPAH8 released to the atmosphere with a national-use estimate of coal-tar-based sealant suggests that PAH emissions from new coal-tar-based sealcoat applications each year (~1000 Mg) are larger than annual vehicle emissions of PAHs for the United States.

Seal ring installation tool

NASA Technical Reports Server (NTRS)

Haselmaier, L. Haynes (Inventor)

2004-01-01

A seal ring tool that allows an installer to position a primary seal ring between hub ends of pipe flanges that are being assembled together. The tool includes a pivoting handle member and extension arms attached to the pivoting handle member. The ends of the arms have side indentation type longitudinal grooves angled toward one another for holding the primary seal ring in place between the hubs of respective pipes that are to be attached together. The arms of the tool can also have flat sides that can be used to abut against an optional second larger seal that is supported within a groove in one of the hub ends so that the second hub end can then be moved against the other side of the primary seal ring. Once the seal ring is positioned between the pipe hubs, the pipe hubs can be moved about the seal ring due to the flat sides of the arms of the tool. The tool eliminates the chances of damaging and contaminating seal rings being installed within pipe hubs that are being attached to one another.

Supercritical-Fluid Extraction of Oil From Tar Sands

NASA Technical Reports Server (NTRS)

Compton, L. E.

1982-01-01

New supercritical solvent mixtures have been laboratory-tested for extraction of oil from tar sands. Mixture is circulated through sand at high pressure and at a temperature above critical point, dissolving organic matter into the compressed gas. Extract is recovered from sand residues. Low-temperature super-critical solvents reduce energy consumption and waste-disposal problems.

Seals Research at AlliedSignal

NASA Technical Reports Server (NTRS)

Ullah, M. Rifat

1996-01-01

A consortium has been formed to address seal problems in the Aerospace sector of Allied Signal, Inc. The consortium is represented by makers of Propulsion Engines, Auxiliary Power Units, Gas Turbine Starters, etc. The goal is to improve Face Seal reliability, since Face Seals have become reliability drivers in many of our product lines. Several research programs are being implemented simultaneously this year. They include: Face Seal Modeling and Analysis Methodology; Oil Cooling of Seals; Seal Tracking Dynamics; Coking Formation & Prevention; and Seal Reliability Methods.

Sodium sulfur battery seal

DOEpatents

Mikkor, Mati

1981-01-01

This disclosure is directed to an improvement in a sodium sulfur battery construction in which a seal between various battery compartments is made by a structure in which a soft metal seal member is held in a sealing position by holding structure. A pressure applying structure is used to apply pressure on the soft metal seal member when it is being held in sealing relationship to a surface of a container member of the sodium sulfur battery by the holding structure. The improvement comprises including a thin, well-adhered, soft metal layer on the surface of the container member of the sodium sulfur battery to which the soft metal seal member is to be bonded.

Preparation of Composite Coating on AZ91D Magnesium Alloy by Silica Sol-Micro Oxidation

NASA Astrophysics Data System (ADS)

Shao, Zhongcai; Zhang, Feifei; Zhao, Ruiqiang; Shen, Xiaoyi

2016-03-01

Composite coating was prepared on AZ91D magnesium alloy with a new method which combined silica sol with micro-arc oxidation (MAO). The MAO coating was prepared on the basis of MAO solution, and then coated by sol-gel process. The composite coating was obtained after second MAO treatment. Scanning electron microscopy coupled with X-ray diffraction (XRD), energy spectrum analysis and electrochemical testing was applied to characterize the properties of MAO coating and composite coating. The experimental test results indicated that the Si element derived from SiO2 gel particle embedded into the MAO coating by second MAO treatment. The surface of composite coating became dense and the holes were smaller with silica sol sealing process. The corrosion resistance of composite coating was improved than the MAO coating.

Bone remodelling around HA-coated acetabular cups

PubMed Central

Nielsen, P. T.; Søballe, K.

2006-01-01

This study was designed to investigate bone remodelling around the cup in cementless THA. Previous studies indicate an advantage of better sealing of the bone-prosthesis interface by HA/TCP coating of implants, inhibiting polyethylene-induced osteolysis. One hundred patients gave informed consent to participate in a controlled randomized study between porous coated Trilogy versus Trilogy Calcicoat (HA/TCP coated). The cup was inserted in press-fit fixation. The femoral component was a cementless porous coated titanium alloy stem (Bi-Metric), with a modular 28-mm CrCo head. The Harris Hip Score (HHS) and bone mineral density (BMD) determined by DEXA scanning were used to study the effect. Measurements revealed no difference between the two groups after 3 years either in the clinical outcome or in terms of periprosthetic bone density. Patients with a body mass index above normal regained more bone mineral than patients with normal weight. This finding supports the assumption that load is beneficial to bone remodelling. PMID:16761153

The search for a source rock for the giant Tar Sand triangle accumulation, southeastern Utah

USGS Publications Warehouse

Huntoon, J.E.; Hansley, P.L.; Naeser, N.D.

1999-01-01

A large proportion (about 36%) of the world's oil resource is contained in accumulations of heavy oil or tar. In these large deposits of degraded oil, the oil in place represents only a fraction of what was present at the time of accumulation. In many of these deposits, the source of the oil is unknown, and the oil is thought to have migrated over long distances to the reservoirs. The Tar Sand triangle in southeastern Utah contains the largest tar sand accumulation in the United States, with 6.3 billion bbl of heavy oil estimated to be in place. The deposit is thought to have originally contained 13-16 billion bbl prior to the biodegradation, water washing, and erosion that have taken place since the middle - late Tertiary. The source of the oil is unknown. The tar is primarily contained within the Lower Permian White Rim Sandstone, but extends into permeable parts of overlying and underlying beds. Oil is interpreted to have migrated into the White Rim sometime during the Tertiary when the formation was at a depth of approximately 3500 m. This conclusion is based on integration of fluid inclusion analysis, time-temperature reconstruction, and apatite fission-track modeling for the White Rim Sandstone. Homogenization temperatures cluster around 85-90??C for primary fluid inclusions in authigenic, nonferroan dolomite in the White Rim. The fluid inclusions are associated with fluorescent oil-bearing inclusions, indicating that dolomite precipitation was coeval with oil migration. Burial reconstruction suggests that the White Rim Sandstone reached its maximum burial depth from 60 to 24 Ma, and that maximum burial was followed by unroofing from 24 to 0 Ma. Time-temperature modeling indicates that the formation experienced temperatures of 85-90??C from about 35 to 40 Ma during maximum burial. Maximum formation temperatures of about 105-110??C were reached at about 24 Ma, just prior to unroofing. Thermal modeling is used to examine the history of potential source rocks

Turbine disc sealing assembly

DOEpatents

Diakunchak, Ihor S.

2013-03-05

A disc seal assembly for use in a turbine engine. The disc seal assembly includes a plurality of outwardly extending sealing flange members that define a plurality of fluid pockets. The sealing flange members define a labyrinth flow path therebetween to limit leakage between a hot gas path and a disc cavity in the turbine engine.

Improvements in Boron Plate Coating Technology for Higher Efficiency Neutron Detection and Coincidence Counting Error Reduction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menlove, Howard Olsen; Henzlova, Daniela

This informal report presents the measurement data and information to document the performance of the advanced Precision Data Technology, Inc. (PDT) sealed cell boron-10 plate neutron detector that makes use of the advanced coating materials and procedures. In 2015, PDT changed the boron coating materials and application procedures to significantly increase the efficiency of their basic corrugated plate detector performance. A prototype sealed cell unit was supplied to LANL for testing and comparison with prior detector cells. Also, LANL had reference detector slabs from the original neutron collar (UNCL) and the new Antech UNCL with the removable 3He tubes. Themore » comparison data is presented in this report.« less

Impact of Genetic Variations in HIV-1 Tat on LTR-Mediated Transcription via TAR RNA Interaction.

PubMed

Ronsard, Larance; Ganguli, Nilanjana; Singh, Vivek K; Mohankumar, Kumaravel; Rai, Tripti; Sridharan, Subhashree; Pajaniradje, Sankar; Kumar, Binod; Rai, Devesh; Chaudhuri, Suhnrita; Coumar, Mohane S; Ramachandran, Vishnampettai G; Banerjea, Akhil C

2017-01-01

HIV-1 evades host defense through mutations and recombination events, generating numerous variants in an infected patient. These variants with an undiminished virulence can multiply rapidly in order to progress to AIDS. One of the targets to intervene in HIV-1 replication is the trans -activator of transcription (Tat), a major regulatory protein that transactivates the long terminal repeat promoter through its interaction with trans -activation response (TAR) RNA. In this study, HIV-1 infected patients ( n = 120) from North India revealed Ser46Phe (20%) and Ser61Arg (2%) mutations in the Tat variants with a strong interaction toward TAR leading to enhanced transactivation activities. Molecular dynamics simulation data verified that the variants with this mutation had a higher binding affinity for TAR than both the wild-type Tat and other variants that lacked Ser46Phe and Ser61Arg. Other mutations in Tat conferred varying affinities for TAR interaction leading to differential transactivation abilities. This is the first report from North India with a clinical validation of CD4 counts to demonstrate the influence of Tat genetic variations affecting the stability of Tat and its interaction with TAR. This study highlights the co-evolution pattern of Tat and predominant nucleotides for Tat activity, facilitating the identification of genetic determinants for the attenuation of viral gene expression.

Method of producing drive fluid in situ in tar sands formations

DOEpatents

Mudunuri, Ramesh Raju; Jaiswal, Namit; Vinegar, Harold J.; Karanikas, John Michael

2010-03-23

Methods of treating a tar sands formation are described herein. Methods for treating a tar sands may include providing heat to at least part of a hydrocarbon layer in the formation from one or more heaters located in the formation. The heat may be allowed to transfer from the heaters to at least a portion of the formation such that a drive fluid is produced in situ in the formation. The drive fluid may move at least some mobilized, visbroken, and/or pyrolyzed hydrocarbons from a first portion of the formation to a second portion of the formation. At least some of the mobilized, visbroken, and/or pyrolyzed hydrocarbons may be produced from the formation.

Bidirectional Brush Seals

NASA Technical Reports Server (NTRS)

Hendricks, Robert C.; Wilson, Jack; Wu, Tom; Flower, Ralph

1997-01-01

Presented is a study of the use of a set of I.D./O.D. bidirectional press seals to reduce the leakage losses in a wave rotor. Relative to the baseline configuration, data indicate the use of brush seals enhanced wave rotor efficiency from 36 to 45 percent at low leakages (small rotor endwall gap spacings) and from 15 to 33 percent at high leakages (larger endwall gap spacings). These brush seals are capable of sealing positive or negative pressure drops with respect to the axial direction. Surface tribology for these tests suggested little evidence of grooving although the bristles appeared polished.

Marketing 'less harmful, low-tar' cigarettes is a key strategy of the industry to counter tobacco control in China.

PubMed

Yang, Gonghuan

2014-03-01

While the 'low-tar' scheme has been widely recognised as a misleading tactic used by the tobacco industry to deceive the public about the true risks of cigarette smoking, a similar campaign using the slogan of 'less harmful, low tar' was launched by the Chinese tobacco industry, that is, State Tobacco Monopoly Administration/China National Tobacco Corporation and began to gain traction during the last decade. Despite the fact that no sufficient research evidence supports the claims made by the industry that these cigarettes are safer, the Chinese tobacco industry has continued to promote them using various health claims. As a result, the production and sales of 'less harmful, low-tar' cigarettes have increased dramatically since 2000. Recently, a tobacco industry senior researcher, whose main research area is 'less harmful, low-tar' cigarettes, was elected as an Academician to the prestigious Chinese Academy of Engineering for his contribution to developing 'less harmful, low-tar' cigarettes. The tobacco researcher's election caused an outcry from the tobacco control community and the general public in China. This paper discusses the Chinese tobacco industry's 'less harmful, low-tar' initiatives and calls for the Chinese government to stop the execution of this deceptive strategy for tobacco marketing.

Relationship between cigarette format and mouth-level exposure to tar and nicotine in smokers of Russian king-size cigarettes.

PubMed

Ashley, Madeleine; Dixon, Mike; Prasad, Krishna

2014-10-01

Differences in length and circumference of cigarettes may influence smoker behaviour and exposure to smoke constituents. Superslim king-size (KSSS) cigarettes (17mm circumference versus 25mm circumference of conventional king-size [KS] cigarettes), have gained popularity in several countries, including Russia. Some smoke constituents are lower in machine-smoked KSSS versus KS cigarettes, but few data exist on actual exposure in smokers. We investigated mouth-level exposure (MLE) to tar and nicotine in Russian smokers of KSSS versus KS cigarettes and measured smoke constituents under machine-smoking conditions. MLE to tar was similar for smokers of 1mg ISO tar yield products, but lower for smokers of 4mg and 7mg KSSS versus KS cigarettes. MLE to nicotine was lower in smokers of 4mg KSSS versus KS cigarettes, but not for other tar bands. No gender differences were observed for nicotine or tar MLE. Under International Organization for Standardization, Health Canada Intense and Massachusetts regimes, KSSS cigarettes tended to yield less carbon monoxide, acetaldehyde, nitric oxide, acrylonitrile, benzene, 1,3-butadiene and tobacco-specific nitrosamines, but more formaldehyde, than KS cigarettes. In summary, differences in MLE were observed between cigarette formats, but not systematically across pack tar bands. Copyright © 2014 The Authors. Published by Elsevier Inc. All rights reserved.

The fat and the furriest: morphological changes in harp seal fur with ontogeny.

PubMed

Gmuca, Natalia V; Pearson, Linnea E; Burns, Jennifer M; Liwanag, Heather E M

2015-01-01

Ontogenetic changes in physiological performance often exemplify the development of adaptations to environmental challenges. For mammals in polar regions, the extreme cold of the environment presents a constant challenge to thermal homeostasis. The harp seal (Pagophilus groenlandicus) is an Arctic species that shifts its thermoregulatory strategy with ontogeny. Adult harp seals primarily use blubber for insulation, but newborn harp seals instead rely on their fur coat while their blubber layer develops. Harp seal pups are weaned abruptly, less than 2 wk after birth, and must subsequently learn to swim and dive in frigid waters on their own. This study examined how the morphological characteristics of harp seal fur change with ontogeny. We compared hair length, hair circularity, and hair density for neonates (1 d old; n = 7), early-nursing pups (4 d old; n = 3), late-nursing pups (9 d old; n = 4), newly weaned (molting) pups (2 wk old; n = 5), late-weaned (molted) pups (3 wk old; n = 4), and adult harp seals (n = 4). Hairs were shorter (P < 0.001) and flatter (P < 0.001) in older animals. Additionally, hair density decreased with age (P < 0.001), in terms of both the average number of hair bundles per unit area and the average number of underhairs present in any given bundle. These morphological changes were associated with a reduced thermal resistance of the pelt in late-weaned (molted) pups and adults (P < 0.001). Results are consistent with known evolutionary patterns of fur morphology associated with the transition from fur to blubber in aquatic species, yet this is the first time such morphological differences have been demonstrated across age classes within a single species. Thus, the ontogenetic patterns described here for harp seals recapitulate the convergent phylogenetic patterns observed across secondarily aquatic species. Overall, the timing of these ontogenetic changes may limit the ability of harp seals to adapt to the deterioration of sea ice in the

Demineralization of resin-sealed enamel by soft drinks in a clinically relevant pH cycling model.

PubMed

Bartels, Agata A; Evans, Carla A; Viana, Grace; Bedran-Russo, Ana K

2016-04-01

To compare the in vitro protective effect of orthodontic sealants on the enamel demineralization under a soft drink-induced erosive challenge. The facial surfaces of bovine incisors were sectioned into 5 mm x 4 mm x 4 mm enamel blocks. Specimens were randomly assigned to three surface protection measures: control (exposed enamel), coating with Transbond XT (unfilled resin primer), or coating with Opal Seal (filled and fluoride releasing primer). Thermocycling was used to simulate aging. The specimens were pH cycled through an acidic buffer, test beverage and a neutral buffer for a total of 7 days. Test beverages included water, Diet Mountain Dew, and Coke Classic. Quantitative light-induced fluorescence (QLF) images were taken at baseline and after aging. Final QLF images were taken to evaluate the demineralization of enamel. Data were analyzed statistically using a two-way ANOVA to compare the interaction between enamel surface protection and beverages as well as one-way ANOVA to compare surface protection and the test beverage levels. A statistically significant interaction was found between the surface protected groups and the test beverage groups (P < 0.05). Statistically significant differences were found among the test beverage groups (P < 0.05) and among the surface protection groups (P < 0.05). Coke Classic went through the sealant layer resulting in high enamel demineralization. Enamel coating with Opal Seal significantly reduced the erosive attack of beverages.

Overview of NASA Glenn Seal Program

NASA Technical Reports Server (NTRS)

Steinetz, Bruce M.; Proctor, Margaret P.; Dunlap, Patrick H., Jr.; Delgado, Irebert; DeMange, Jeffrey J.; Daniels, Christopher C.; Lattime, Scott B.

2003-01-01

The Seal Team is divided into four primary areas. These areas include turbine engine seal development, structural seal development, acoustic seal development, and adaptive seal development. The turbine seal area focuses on high temperature, high speed shaft seals for secondary air system flow management. The structural seal area focuses on high temperature, resilient structural seals required to accommodate large structural distortions for both space- and aero-applications. Our goal in the acoustic seal project is to develop non-contacting, low leakage seals exploiting the principles of advanced acoustics. We are currently investigating a new acoustic field known as Resonant Macrosonic Synthesis (RMS) to see if we can harness the large acoustic standing pressure waves to form an effective air-barrier/seal. Our goal in the adaptive seal project is to develop advanced sealing approaches for minimizing blade-tip (shroud) or interstage seal leakage. We are planning on applying either rub-avoidance or regeneration clearance control concepts (including smart structures and materials) to promote higher turbine engine efficiency and longer service lives.

A hybrid floating brush seal (HFBS) for improved sealing and wear performance in turbomachinery applications

NASA Astrophysics Data System (ADS)

Lattime, Scott Byran

A conceptually new type of seal has been developed for gas turbine applications which dramatically reduces wear and leakage associated with current labyrinth and brush seal technologies. The Hybrid Floating Brush Seal (HFBS) combines brush seal and film riding face seal technologies to create a hybrid seal that allows both axial and radial excursions of the sealed shaft, while simultaneously eliminating interface surface speeds (friction and heat) between the rotor and the brush material that characterize standard brush seal technology. A simple test rig was designed to evaluate feasibility of the HFBS under relatively low pressures and rotational speeds (50psig, 5krpm). A second test stand was created to study the effects of centrifugal force on bristle deflection. A third test facility was constructed for prototype development and extensive room temperature testing at moderate pressures and fairly high rotational speeds (100psig, 40krpm). This test rig also allowed the evaluation of the HFBS during axial movement of a rotating shaft. An analytical model to predict the effects of centrifugal force on the bristles of a rotating brush seal was developed. Room temperature analysis of the HFBS proved successful for relatively high operating rotational velocities at moderate pressures with very acceptable leakage rates for gas turbine engines. Brush seals were able to track rotor speeds up to 24krpm while maintaining sealing integrity. The HFBS's ability to function under axial shaft displacement and synchronous dynamic radial loading was also proven successful. Hydrodynamic performance of the face seal was proven to provide adequate stiffness and load carrying capacity to keep the brush seal from contacting the face seal at pressure drops across the brush of up to 100psi. Leakage performance over standard brush seal and labyrinth technology was quite dramatic. The HFBS showed its sealing advantage using much higher radial interference between the rotor and the bristle

Identification and characterization of a HeLa nuclear protein that specifically binds to the trans-activation-response (TAR) element of human immunodeficiency virus.

PubMed Central

Marciniak, R A; Garcia-Blanco, M A; Sharp, P A

1990-01-01

Human immunodeficiency virus type 1 RNAs contain a sequence, trans-activation-response (TAR) element, which is required for tat protein-mediated trans-activation of viral gene expression. We have identified a nuclear protein from extracts of HeLa cells that binds to the TAR element RNA in a sequence-specific manner. The binding of this 68-kDa polypeptide was detected by UV cross-linking proteins to TAR element RNA transcribed in vitro. Competition experiments were performed by using a partially purified preparation of the protein to quantify the relative binding affinities of TAR element RNA mutants. The binding affinity of the TAR mutants paralleled the reported ability of those mutants to support tat trans-activation in vivo. We propose that this cellular protein moderates TAR activity in vivo. Images PMID:2333305

Hydrodynamic perception in true seals (Phocidae) and eared seals (Otariidae).

PubMed

Hanke, Wolf; Wieskotten, Sven; Marshall, Christopher; Dehnhardt, Guido

2013-06-01

Pinnipeds, that is true seals (Phocidae), eared seals (Otariidae), and walruses (Odobenidae), possess highly developed vibrissal systems for mechanoreception. They can use their vibrissae to detect and discriminate objects by direct touch. At least in Phocidae and Otariidae, the vibrissae can also be used to detect and analyse water movements. Here, we review what is known about this ability, known as hydrodynamic perception, in pinnipeds. Hydrodynamic perception in pinnipeds developed convergently to the hydrodynamic perception with the lateral line system in fish and the sensory hairs in crustaceans. So far two species of pinnipeds, the harbour seal (Phoca vitulina) representing the Phocidae and the California sea lion (Zalophus californianus) representing the Otariidae, have been studied for their ability to detect local water movements (dipole stimuli) and to follow hydrodynamic trails, that is the water movements left behind by objects that have passed by at an earlier point in time. Both species are highly sensitive to dipole stimuli and can follow hydrodynamic trails accurately. In the individuals tested, California sea lions were clearly more sensitive to dipole stimuli than harbour seals, and harbour seals showed a superior trail following ability as compared to California sea lions. Harbour seals have also been shown to derive additional information from hydrodynamic trails, such as motion direction, size and shape of the object that caused the trail (California sea lions have not yet been tested). The peculiar undulated shape of the harbour seals' vibrissae appears to play a crucial role in trail following, as it suppresses self-generated noise while the animal is swimming.

Pyrolysis characteristics and kinetics of acid tar waste from crude benzol refining: A thermogravimetry-mass spectrometry analysis.

PubMed

Chihobo, Chido H; Chowdhury, Arindrajit; Kuipa, Pardon K; Simbi, David J

2016-12-01

Pyrolysis is an attractive thermochemical conversion technology that may be utilised as a safe disposal option for acid tar waste. The kinetics of acid tar pyrolysis were investigated using thermogravimetry coupled with mass spectrometry under a nitrogen atmosphere at different heating rates of 10, 15 and 20 K min -1 The thermogravimetric analysis shows three major reaction peaks centred around 178 °C, 258 °C, and 336 °C corresponding to the successive degradation of water soluble lower molecular mass sulphonic acids, sulphonated high molecular mass hydrocarbons, and high molecular mass hydrocarbons. The kinetic parameters were evaluated using the iso-conversional Kissinger-Akahira-Sunose method. A variation in the activation energy with conversion revealed that the pyrolysis of the acid tar waste progresses through complex multi-step kinetics. Mass spectrometry results revealed a predominance of gases such as hydrogen, methane and carbon monoxide, implying that the pyrolysis of acid tar waste is potentially an energy source. Thus the pyrolysis of acid tar waste may present a viable option for its environmental treatment. There are however, some limitations imposed by the co-evolution of corrosive gaseous components for which appropriate considerations must be provided in both pyrolysis reactor design and selection of construction materials. © The Author(s) 2016.

Social-cognitive remediation in schizophrenia: generalization of effects of the Training of Affect Recognition (TAR).

PubMed

Wölwer, Wolfgang; Frommann, Nicole

2011-09-01

In the last decade, several social cognitive remediation programs have been developed for use in schizophrenia. Though existing evidence indicates that such programs can improve social cognition, which is essential for successful social functioning, it remains unclear whether the improvements generalize to social cognitive domains not primarily addressed by the intervention and whether the improved test performance transfers into everyday social functioning. The present study investigated whether, beyond its known effects on facial affect recognition, the Training of Affect Recognition (TAR) has effects on prosodic affect recognition, theory of mind (ToM) performance, social competence in a role-play task, and more general social and occupational functioning. Thirty-eight inpatients with a diagnosis of schizophrenia or schizoaffective disorder were randomly assigned to 6 weeks of treatment with the TAR--primarily targeted at facial affect recognition-or Cognitive Remediation Training (CRT)--primarily targeted at neurocognition. Intention-to-treat analyses found significantly larger pre-post improvements with TAR than with CRT in prosodic affect recognition, ToM, and social competence and a trend effect in global social functioning. However, the effects on ToM and social competence were no longer significant in the smaller group of patients who completed treatment according to protocol. Results suggest that TAR effects generalize to other social cognitive domains not primarily addressed. TAR may also enhance social skills and social functioning, although this has to be confirmed. Results are discussed with regard to the need to improve functional outcome in schizophrenia against the background of current evidence from other social cognitive remediation approaches.

A hot dynamic seal rig for measuring hypersonic engine seal durability and flow performance

NASA Technical Reports Server (NTRS)

Miller, Jeffrey H.; Steinetz, Bruce M.; Sirocky, Paul J.; Kren, Lawrence A.

1993-01-01

A test fixture for measuring the dynamic performance of candidate high-temperature engine seal concepts has been installed at NASA Lewis Research Center. The test fixture has been designed to evaluate seal concepts under development for advanced hypersonic engines, such as those being considered for the National Aerospace Plane (NASP). The fixture can measure dynamic seal leakage performance from room temperature up to 840 C (1550 F) and air pressure differentials up to 690 kPa (100 psi). Performance of the seals can be measured while sealing against flat or distorted walls. In the fixture two seals are preloaded against the sides of a 30 cm (1 ft) long saber that slides transverse to the axis of the seals, simulating the scrubbing motion anticipated in these engines. This report covers the capabilities of this test fixture along with preliminary data showing the dependence of seal leakage performance on high temperature cycling.

A Hot Dynamic Seal Rig for Measuring Hypersonic Engine Seal Durability and Flow Performance

NASA Technical Reports Server (NTRS)

Miller, Jeffrey H.; Steinetz, Bruce M.; Sirocky, Paul J.; Kren, Lawrence A.

1993-01-01

A test fixture for measuring the dynamic performance of candidate high-temperature engine seal concepts was installed at NASA Lewis Research Center. The test fixture was designed to evaluate seal concepts under development for advanced hypersonic engines, such as those being considered for the National Aerospace Plane (NASP). The fixture can measure dynamic seal leakage performance from room temperature up to 840 C (1550 F) and air pressure differentials up to 690 kPa (100 psi). Performance of the seals can be measured while sealing against flat or distorted walls. In the fixture two seals are preloaded against the sides of a 30 cm (1 ft) long saber that slides transverse to the axis of the seals, simulating the scrubbing motion anticipated in these engines. The capabilities of this test fixture along with preliminary data showing the dependence of seal leakage performance on high temperature cycling are addressed.

Shaft seal assembly and method

NASA Technical Reports Server (NTRS)

Keba, John E. (Inventor)

2007-01-01

A pressure-actuated shaft seal assembly and associated method for controlling the flow of fluid adjacent a rotatable shaft are provided. The seal assembly includes one or more seal members that can be adjusted between open and closed positions, for example, according to the rotational speed of the shaft. For example, the seal member can be configured to be adjusted according to a radial pressure differential in a fluid that varies with the rotational speed of the shaft. In addition, in the closed position, each seal member can contact a rotatable member connected to the shaft to form a seal with the rotatable member and prevent fluid from flowing through the assembly. Thus, the seal can be closed at low speeds of operation and opened at high speeds of operation, thereby reducing the heat and wear in the seal assembly while maintaining a sufficient seal during all speeds of operation.

30 CFR 57.8535 - Seals.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Seals. 57.8535 Section 57.8535 Mineral....8535 Seals. Seals shall be provided with a means for checking the quality of air behind the seal and a means to prevent a water head from developing unless the seal is designed to impound water. ...

30 CFR 57.8535 - Seals.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Seals. 57.8535 Section 57.8535 Mineral....8535 Seals. Seals shall be provided with a means for checking the quality of air behind the seal and a means to prevent a water head from developing unless the seal is designed to impound water. ...

Resilient Braided Rope Seal

NASA Technical Reports Server (NTRS)

Steinetz, Bruce M. (Inventor); Kren, Lawrence A. (Inventor)

1996-01-01

A resilient braided rope seal for use in high temperature applications. The resilient braided rope seal includes a center core of fibers, a resilient 5 member overbraided by at least one layer of braided sheath fibers tightly packed together. The resilient member adds significant stiffness to the seal while maintaining resiliency. Furthermore, the seal permanent set and hysteresis are greatly reduced. Finally, improved load capabilities are provided.

Rotary shaft seal

DOEpatents

Langebrake, C.O.

1984-01-01

The invention is a novel rotary shaft seal assembly which provides positive-contact sealing when the shaft is not rotated and which operates with its sealing surfaces separated by a film of compressed ambient gas whose width is independent of the speed of shaft rotation. In a preferred embodiment, the assembly includes a disc affixed to the shaft for rotation therewith. Axially movable, non-rotatable plates respectively supported by sealing bellows are positioned on either side of the disc to be in sealing engagement therewith. Each plate carries piezoelectric transucer elements which are electrically energized at startup to produce films of compressed ambient gas between the confronting surfaces of the plates and the disc. Following shutdown of the shaft, the transducer elements are de-energized. A control circuit responds to incipient rubbing between the plate and either disc by altering the electrical input to the transducer elements to eliminate rubbing.

Rotary shaft seal

DOEpatents

Langebrake, Clair O.

1984-01-01

The invention is a novel rotary shaft seal assembly which provides positive-contact sealing when the shaft is not rotated and which operates with its sealing surfaces separated by a film of compressed ambient gas whose width is independent of the speed of shaft rotation. In a preferred embodiment, the assembly includes a disc affixed to the shaft for rotation therewith. Axially movable, non-rotatable plates respectively supported by sealing bellows are positioned on either side of the disc to be in sealing engagement therewith. Each plate carries piezoelectric transducer elements which are electrically energized at startup to produce films of compressed ambient gas between the confronting surfaces of the plates and the disc. Following shutdown of the shaft, the transducer elements are de-energized. A control circuit responds to incipient rubbing between the plate and either disc by altering the electrical input to the transducer elements to eliminate rubbing.

Sealing in Turbomachinery

NASA Technical Reports Server (NTRS)

Chupp, Raymond E.; Hendricks, Robert C.; Lattime, Scott B.; Steinetz, Bruce M.

2006-01-01

Clearance control is of paramount importance to turbomachinery designers and is required to meet today's aggressive power output, efficiency, and operational life goals. Excessive clearances lead to losses in cycle efficiency, flow instabilities, and hot gas ingestion into disk cavities. Insufficient clearances limit coolant flows and cause interface rubbing, overheating downstream components and damaging interfaces, thus limiting component life. Designers have put renewed attention on clearance control, as it is often the most cost effective method to enhance system performance. Advanced concepts and proper material selection continue to play important roles in maintaining interface clearances to enable the system to meet design goals. This work presents an overview of turbomachinery sealing to control clearances. Areas covered include: characteristics of gas and steam turbine sealing applications and environments, benefits of sealing, types of standard static and dynamics seals, advanced seal designs, as well as life and limitations issues.

Applying high-emittance and solar-absorptance coating to aluminum

NASA Technical Reports Server (NTRS)

Progar, D. J.

1973-01-01

Coated surface withstands space environment with negilgible change in radiation characteristics and physical properties. Process can be used with any porous substance, as long as pores are large enough to allow molecules of reacting solutions to enter and yet not so large as to allow nickel sulfide to be leached out of pores before sealing.

Mechanically expandable annular seal

DOEpatents

Gilmore, R.F.

1983-07-19

A mechanically expandable annular reusable seal assembly to form an annular hermetic barrier between two stationary, parallel, and planar containment surfaces is described. A rotatable ring, attached to the first surface, has ring wedges resembling the saw-tooth array of a hole saw. Matching seal wedges are slidably attached to the ring wedges and have their motion restricted to be perpendicular to the second surface. Each seal wedge has a face parallel to the second surface. An annular elastomer seal has a central annular region attached to the seal wedges' parallel faces and has its inner and outer circumferences attached to the first surface. A rotation of the ring extends the elastomer seal's central region perpendicularly towards the second surface to create the fluid tight barrier. A counter rotation removes the barrier. 6 figs.

Seals Code Development Workshop

NASA Technical Reports Server (NTRS)

Hendricks, Robert C. (Compiler); Liang, Anita D. (Compiler)

1996-01-01

Seals Workshop of 1995 industrial code (INDSEAL) release include ICYL, GCYLT, IFACE, GFACE, SPIRALG, SPIRALI, DYSEAL, and KTK. The scientific code (SCISEAL) release includes conjugate heat transfer and multidomain with rotordynamic capability. Several seals and bearings codes (e.g., HYDROFLEX, HYDROTRAN, HYDROB3D, FLOWCON1, FLOWCON2) are presented and results compared. Current computational and experimental emphasis includes multiple connected cavity flows with goals of reducing parasitic losses and gas ingestion. Labyrinth seals continue to play a significant role in sealing with face, honeycomb, and new sealing concepts under investigation for advanced engine concepts in view of strict environmental constraints. The clean sheet approach to engine design is advocated with program directions and anticipated percentage SFC reductions cited. Future activities center on engine applications with coupled seal/power/secondary flow streams.

Layered seal for turbomachinery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sarawate, Neelesh Nandkumar; Morgan, Victor John; Weber, David Wayne

2015-11-20

The present application provides seal assemblies for reducing leakages between adjacent components of turbomachinery. The seal assemblies may include outer shims, and at least a portion of the outer shims may be substantially impervious. At least one of the outer shims may be configured for sealing engagement with seal slots of the adjacent components. The seal assemblies may also include at least one of an inner shim and a filler layer positioned between the outer shims. The at least one inner shim may be substantially solid and the at least one filler layer may be relatively porous. The seal assembliesmore » may be sufficiently flexible to account for misalignment between the adjacent components, sufficiently stiff to meet assembly requirements, and sufficiently robust to operating meet requirements associated with turbomachinery.« less

Liquid zone seal

DOEpatents

Klebanoff, Leonard E.

2001-01-01

A seal assembly that provides a means for establishing multiple pressure zones within a system. The seal assembly combines a plate extending from the inner wall of a housing or inner enclosure that intersects with and is immersed in the fluid contained in a well formed in a tray contained within the enclosure. The fluid is a low vapor pressure oil, chemically inert and oxidation resistant. The use of a fluid as the sealing component provides a seal that is self-healing and mechanically robust not subject to normal mechanical wear, breakage, and formation of cracks or pinholes and decouples external mechanical vibrations from internal structural members.

In situ heat treatment of a tar sands formation after drive process treatment

DOEpatents

Vinegar, Harold J.; Stanecki, John

2010-09-21

A method for treating a tar sands formation includes providing a drive fluid to a hydrocarbon containing layer of the tar sands formation to mobilize at least some hydrocarbons in the layer. At least some first hydrocarbons from the layer are produced. Heat is provided to the layer from one or more heaters located in the formation. At least some second hydrocarbons are produced from the layer of the formation. The second hydrocarbons include at least some hydrocarbons that are upgraded compared to the first hydrocarbons produced by using the drive fluid.

Cigarettes, lung cancer, and coronary heart disease: the effects of inhalation and tar yield.

PubMed

Higenbottam, T; Shipley, M J; Rose, G

1982-06-01

Ten-year mortality rates for lung cancer and coronary heart disease have been related to cigarette smoking habits in 17 475 male civil servants aged 40-64 and in sample of 8089 male British residents aged 35-69. Both diseases were more frequent in smokers. Lung cancer rates were higher overall for "non-inhalers", particularly in heavy smokers. Tar yield correlated with the risk of lung cancer in non-inhalers but less so in inhalers. Conversely, coronary deaths were more common among inhalers, and the effect of tar/nicotine yield (such as it was) was confined to inhalers. It appears that there are subtle interactions between the amount smoked, the tar/nicotine yield of the cigarette, and the style of smoking. Thus the effects of a change in cigarette characteristics are hard to predict, and they may be different for respiratory and cardiovascular disease.

Properties of gasification-derived char and its utilization for catalytic tar reforming

NASA Astrophysics Data System (ADS)

Qian, Kezhen

Char is a low-value byproduct of biomass gasification and pyrolysis with many potential applications, such as soil amendment and the synthesis of activated carbon. The overall goal of the proposed research was to develop novel methods to use char derived from gasification for high-value applications in syngas conditioning. The first objective was to investigate effects of gasification condition and feedstock on properties of char derived from fluidized bed gasification. Results show that the surface areas of most of the char were 1--10 m 2/g and increased as the equivalence ratio increased. Char moisture and fixed carbon contents decreased while ash content increased as equivalence ratio increased. The next objective was to study the properties of sorghum and red cedar char derived from downdraft gasifier. Red cedar char contained more aliphatic carbon and o-alkyl carbon than sorghum char. Char derived from downdraft gasification had higher heating values and lower ash contents than char derived from fluidized bed gasification. The gasification reactivity of red cedar char was higher than that of sorghum char. Then, red cedar char based catalysts were developed with different preparation method to reform toluene and naphthalene as model tars. The catalyst prepared with nickel nitrate was found to be better than that with nickel acetate. The nickel particle size of catalyst impregnated with nickel nitrate was smaller than that of catalyst impregnated with nickel acetate. The particle size of catalyst impregnated with nickel acetate decreased by hydrazine reduction. The catalyst impregnated with nickel nitrate had the highest toluene removal efficiency, which was 70%--100% at 600--800 °C. The presence of naphthalene in tar reduced the catalyst efficiency. The toluene conversion was 36--99% and the naphthalene conversion was 37%--93% at 700--900 °C. Finally, effects of atmosphere and pressure on catalytic reforming of lignin-derived tars over the developed catalyst

Ultra high vacuum seal arrangement

DOEpatents

Flaherty, Robert

1981-01-01

Arrangement for demountably sealing two concentric metallic tubes in an ultra high vacuum system which facilitates remote actuation. A tubular seal includes integral spaced lips which circumferentially engage the metallic tubes. The lips plastically deform the metallic tubes by mechanical forces resulting from a martensite to austenite transformation of the tubular seal upon application of a predetermined temperature. The sealing force is released upon application of another temperature which causes a transformation from the stronger austenite to the weaker martensite. Use of a dual acting sealing ring and driving ring circumferentially contacting the sealing ring is particularly applicable to sealing larger diameter concentric metallic members.

Core disruptive accident margin seal

DOEpatents

Golden, Martin P.

1979-01-01

Apparatus for sealing the annulus defined within a substantially cylindrical rotatable riser assembly and plug combination of a nuclear reactor closure head. The apparatus comprises an inflatable sealing mechanism disposed in one portion of the riser assembly near the annulus such that upon inflation the sealing mechanism is radially actuated against the other portion of the riser assembly thereby sealing the annulus. The apparatus further comprises a connecting mechanism which places one end of the sealing mechanism in fluid communication with the reactor cover gas so that overpressurization of the reactor cover gas will increase the radial actuation of the sealing mechanism thus enhancing sealing of the annulus.

Seal system with integral detector

DOEpatents

Fiarman, S.

1982-08-12

A seal system is disclosed for materials where security is of the essence, such as nuclear materials. The seal is tamper-indicating, indicates changes in environmental conditions that evidence attempts to bypass the seal, is unique and cost effective. The seal system is comprised of a seal where an optical signal is transmitted through a loop, with a detector to read said signal, and one or more additional detectors designed to detect environmental changes, these detectors being operatively associated with the seal so that detection of a break in the optical signal or detection of environmental changes will cause an observable change in the seal.

Characterization of alkanes, hopanes, and polycyclic aromatic hydrocarbons (PAHs) in tar-balls collected from the East Coast of Peninsular Malaysia.

PubMed

Chandru, Kuhan; Zakaria, Mohamad Pauzi; Anita, Sofia; Shahbazi, Azadeh; Sakari, Mahyar; Bahry, Pourya Shahpoury; Mohamed, Che Abd Rahim

2008-05-01

The East Coast of Peninsular Malaysia faces the South China Sea and is vulnerable to oil pollution because of intense petroleum production activities in the area. The South China Sea is also a favored route for supertankers carrying crude oil to the Far East. Consequently, oil spills can occur, causing pollution and contamination in the surrounding areas. Residual oil spills stranded on coastal beaches usually end up as tar-balls. Elucidating the sources of tar-balls using a molecular marker approach is essential in assessing environmental impacts and perhaps settling legal liabilities for affected parties. This study utilizes a multimodal molecular marker approach through the use of diagnostic ratios of alkanes, hopanes, and polycyclic aromatic hydrocarbons (PAHs) to determine the source, distribution and weathering of tar-balls. Hopane ratios (e.g., C29/C30, and summation C31-C35/C30 ratios) were used to identify the sources of tar-balls. The weathering effects were distinguished by using alkanes, namely the unresolved complex mixture (UCM) and low molecular weight/high molecular weight (L/H) ratios. Similarly, PAHs were also used for the determination of weathering processes undergone by the tar-balls. This multimodal molecular marker gave a very strong indication of the sources of tar-balls in this study. For example, 16 out of 17 samples originated from South East Asian Crude Oil (SEACO) with one sample from Merang, Terengganu originating from North Sea Oil (Troll). The TRME-2 sample may have come from a supertanker's ballast water discharge. The second possibility is that the tar-ball may have been transported via oceanographic currents. All 'weathered' sample characterizations were based on the presence of UCM and other ratios. The multimodal molecular marker approach applied in this study has enabled us to partially understand the transport behavior of tar-balls in the marine environment and has revealed insights into the weathering process of tar-balls.

Multi-pane glass unit having seal with adhesive and hermetic coating layer

DOEpatents

Miller, Seth A; Stark, David H; Francis, IV, William H; Puligandla, Viswanadham; Boulos, Edward N; Pernicka, John

2015-02-10

A vacuum insulated glass unit (VIGU) comprises a first pane of a transparent material and a second pane of a transparent material. The second pane is spaced apart from the first pane to define a cavity therebetween. At least one of a spacer and an array of stand-off members is disposed between the first and second panes to maintain separation therebetween. A first adhesive layer forms at least a portion of a gas-tight connection between the first pane and the second pane. A highly hermetic coating is disposed over the adhesive layer, where the coating is an inorganic layer.

Improved circumferential shaft seal

NASA Technical Reports Server (NTRS)

Ludwig, L. P.; Strom, T. N.

1974-01-01

Comparative tests of modified and unmodified carbon ring seals showed that addition of helical grooves to conventional segmented carbon ring seals reduced leakage significantly. Modified seal was insensitive to shaft runout and to flooding by lubricant.

Exploring the chemical composition of pelagic tar collected in the North Atlantic Ocean

NASA Astrophysics Data System (ADS)

Green, H. S.; Reddy, C. M.; Valentine, D. L.; Aeppli, C.; Swarthout, B.; Sharpless, C.; Joyce, P.; Meyer, A. W.; Fuller, S. A.; Gosselin, K.

2016-12-01

Pelagic tarballs have been linked to multiple sources and their abundances follow notable historical and geographic trends. An overwhelming number of studies point to operational discharges (cargo washing) as the main source of pelagic tar. In a recent review article, Warnock et al. (2015) summarized that the abundance of tar balls has decreased over the last 30 years. The decreasing trend of tarballs has been attributed to the MARPOL 73/78 Annex I legislation, which was created from conventions held in 1973 and again in 1978 to respond to several tanker accidents and other pollution-related inputs. Two of the studies supporting the "MARPOL 73/78 effect" were based on the historical record of tarballs collected in the North Atlantic Ocean by the Sea Education Association (SEA; Woods Hole, MA). To supplement the SEA record, we performed a series of geochemical analyses on 100 of the SEA samples collected from 1988 to 2014. Bulk and gas chromatographic (GC) analyses revealed that the samples were highly variable. For example, the amount of material that could be dissolved in organic solvent but not measured by gas chromatography (referred to as the % GC amenable, a proxy on the distribution of compound classes that compose the tar) ranged from 10 to 80%, although skewed to values less than 40%. Another parameter, based on the GC data, was the perecentage of the resolved relative to the unresolved signal spanned from 0.1 to 1.8. Nine of the sampes would not dissolve in organic solvents and appear to be soot or coal. This study has an operation limitation as we choose to only examine samples > 1 cm (relative to samples smaller than 1mm). Our approach was based on the assumption that these samples were the most unlikely to be weathered and hence retain the genetic features of the initially released tar. While this study does not have the capacity to test confidently the MARPOL 73/78 effect, it does show that pelagic tars are highly variable, which in turn, have

Membrane curvature and the Tol-Pal complex determine polar localization of the chemoreceptor Tar in E. coli.

PubMed

Saaki, Terrens N V; Strahl, Henrik; Hamoen, Leendert W

2018-02-20

Chemoreceptors are localized at the cell poles of Escherichia coli and other rod-shaped bacteria. Over the years different mechanisms have been put forward to explain this polar localization; from stochastic clustering, membrane curvature driven localization, interactions with the Tol-Pal complex, to nucleoid exclusion. To evaluate these mechanisms, we monitored the cellular localization of the aspartate chemoreceptor Tar in different deletion mutants. We did not find any indication for either stochastic cluster formation or nucleoid exclusion. However, the presence of a functional Tol-Pal complex appeared to be essential to retain Tar at cell poles. Interestingly, Tar still accumulated at midcell in tol and in pal deletion mutants. In these mutants, the protein appears to gather at the base of division septa, a region characterised by strong membrane curvature. Chemoreceptors, like Tar, form trimer-of-dimers that bend the cell membrane due to a rigid tripod structure. The curvature approaches the curvature of the cell membrane generated during cell division, and localization of chemoreceptor tripods at curved membrane areas is therefore energetically favourable as it lowers membrane tension. Indeed, when we introduced mutations in Tar that abolish the rigid tripod structure, the protein was no longer able to accumulate at midcell or cell poles. These findings favour a model where chemoreceptor localization in E. coli is driven by strong membrane curvature and association with the Tol-Pal complex. Importance Bacteria have exquisite mechanisms to sense and to adapt to the environment they live in. One such mechanism involves the chemotaxis signal transduction pathway, in which chemoreceptors specifically bind certain attracting or repelling molecules and transduce the signals to the cell. In different rod-shaped bacteria, these chemoreceptors localize specifically to cell poles. Here, we examined the polar localization of the aspartate chemoreceptor Tar in E. coli

Class I cultural resource overview for oil shale and tar sands areas in Colorado, Utah and Wyoming.

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Rourke, D.; Kullen, D.; Gierek, L.

2007-11-01

In August 2005, the U.S. Congress enacted the Energy Policy Act of 2005, Public Law 109-58. In Section 369 of this Act, also known as the 'Oil Shale, Tar Sands, and Other Strategic Unconventional Fuels Act of 2005', Congress declared that oil shale and tar sands (and other unconventional fuels) are strategically important domestic energy resources that should be developed to reduce the nation's growing dependence on oil from politically and economically unstable foreign sources. The Bureau of Land Management (BLM) is developing a Programmatic Environmental Impact Statement (PEIS) to evaluate alternatives for establishing commercial oil shale and tar sandsmore » leasing programs in Colorado, Wyoming, and Utah. This PEIS evaluates the potential impacts of alternatives identifying BLM-administered lands as available for application for commercial leasing of oil shale resources within the three states and of tar sands resources within Utah. The scope of the analysis of the PEIS also includes an assessment of the potential effects of future commercial leasing. This Class I cultural resources study is in support of the Draft Oil Shale and Tar Sands Resource Management Plan Amendments to Address Land Use Allocations in Colorado, Utah, and Wyoming and Programmatic Environmental Impact Statement and is an attempt to synthesize archaeological data covering the most geologically prospective lands for oil shale and tar sands in Colorado, Utah, and Wyoming. This report is based solely on geographic information system (GIS) data held by the Colorado, Utah, and Wyoming State Historic Preservation Offices (SHPOs). The GIS data include the information that the BLM has provided to the SHPOs. The primary purpose of the Class I cultural resources overview is to provide information on the affected environment for the PEIS. Furthermore, this report provides recommendations to support planning decisions and the management of cultural resources that could be impacted by future oil shale

Tar-free fuel gas production from high temperature pyrolysis of sewage sludge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Leguan; Xiao, Bo; Hu, Zhiquan

2014-01-15

Highlights: • High temperature pyrolysis of sewage sludge was efficient for producing tar-free fuel gas. • Complete tar removal and volatile matter release were at elevated temperature of 1300 °C. • Sewage sludge was converted to residual solid with high ash content. • 72.60% of energy conversion efficiency for gas production in high temperature pyrolysis. • Investment and costing for tar cleaning were reduced. - Abstract: Pyrolysis of sewage sludge was studied in a free-fall reactor at 1000–1400 °C. The results showed that the volatile matter in the sludge could be completely released to gaseous product at 1300 °C. Themore » high temperature was in favor of H{sub 2} and CO in the produced gas. However, the low heating value (LHV) of the gas decreased from 15.68 MJ/N m{sup 3} to 9.10 MJ/N m{sup 3} with temperature increasing from 1000 °C to 1400 °C. The obtained residual solid was characterized by high ash content. The energy balance indicated that the most heating value in the sludge was in the gaseous product.« less

Brown carbon in tar balls from smoldering biomass combustion

Treesearch

R. K. Chakrabarty; H. Moosmuller; L.-W. A. Chen; K. Lewis; W. P. Arnott; C. Mazzoleni; M. K. Dubey; C. E. Wold; W. M. Hao; S. M. Kreidenweis

2010-01-01

We report the direct observation of laboratory production of spherical, carbonaceous particles - "tar balls" - from smoldering combustion of two commonly occurring dry mid-latitude fuels. Real-time measurements of spectrally varying absorption Angstrom coefficients (AAC) indicate that a class of light absorbing organic carbon (OC) with wavelength dependent...

Radiocarbon dating of extinct fauna in the Americas recovered from tar pits

NASA Astrophysics Data System (ADS)

Jull, A. J. T.; Iturralde-Vinent, M.; O'Malley, J. M.; MacPhee, R. D. E.; McDonald, H. G.; Martin, P. S.; Moody, J.; Rincón, A.

2004-08-01

We have obtained radiocarbon dates by accelerator mass spectrometry on bones of extinct large mammals from tar pits. Results on some samples of Glyptodon and Holmesina (extinct large mammals similar to armadillos) yielded ages of >25 and >21 ka, respectively. We also studied the radiocarbon ages of three different samples of bones from the extinct Cuban ground sloth, Parocnus bownii, which yielded dates ranging from 4960 ± 280 to 11 880 ± 420 yr BP. In order to remove the tar component pretreat the samples sufficiently to obtain reliable dates, we cleaned the samples by Soxhlet extraction in benzene. Resulting samples of collagenous material were often small.

Ferrules seals

DOEpatents

Smith, James L.

1984-01-01

A device is provided for sealing an inner tube and an outer tube without excessively deforming the tubes. The device includes two ferrules which cooperate to form a vacuum-tight seal between the inner tube and outer tube and having mating surfaces such that overtightening is not possible.

Air Force seal activities

NASA Astrophysics Data System (ADS)

Mayhew, Ellen R.

1994-07-01

Seal technology development is an important part of the Air Force's participation in the Integrated High Performance Turbine Engine Technology (IHPTET) initiative, the joint DOD, NASA, ARPA, and industry endeavor to double turbine engine capabilities by the turn of the century. Significant performance and efficiency improvements can be obtained through reducing internal flow system leakage, but seal environment requirements continue to become more extreme as the engine thermodynamic cycles advance towards these IHPTET goals. Brush seal technology continues to be pursued by the Air Force to reduce leakage at the required conditions. Likewise, challenges in engine mainshaft air/oil seals are also being addressed. Counter-rotating intershaft applications within the IHPTET initiative involve very high rubbing velocities. This viewgraph presentation briefly describes past and current seal research and development programs and gives a summary of seal applications in demonstrator and developmental engine testing.

Investigation of positive shaft seals

NASA Technical Reports Server (NTRS)

Pfouts, J. O.

1970-01-01

Welded metal bellows secondary seals prevent secondary seal leakage with a minimum number of potential leak paths. High performance seal is obtained by controlling the potentially unstable seal-face movements induced by mechanical vibrations and fluid pressure pulsations.

Controlling and assessing pressure conditions during treatment of tar sands formations

DOEpatents

Zhang, Etuan; Beer, Gary Lee

2015-11-10

A method for treating a tar sands formation includes providing heat to at least part of a hydrocarbon layer in the tar sands formation from a plurality of heaters located in the formation. Heat is allowed to transfer from the heaters to at least a portion of the formation. A pressure in the portion of the formation is controlled such that the pressure remains below a fracture pressure of the formation overburden while allowing the portion of the formation to heat to a selected average temperature of at least about 280.degree. C. and at most about 300.degree. C. The pressure in the portion of the formation is reduced to a selected pressure after the portion of the formation reaches the selected average temperature.

Long-term evaluation of solid oxide fuel cell candidate materials in a 3-cell generic short stack fixture, Part II: sealing glass stability, microstructure and interfacial reactions.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chou, Y. S.; Stevenson, Jeffry W.; Choi, Jung-Pyung

2014-03-15

A generic solid oxide fuel cell stack test fixture was developed to evaluate candidate materials and processing methods under realistic conditions. Part I of the work addressed the stack fixture, seal system and cell performance of a 3-cell short stack tested at 800oC for 6000h. Commercial NiO-YSZ anode-supported thin YSZ electrolyte cells with LSM cathodes were used for assessment and were tested in constant current mode with dilute (~50% H2) fuel versus air. Part II of the work examined the sealing glass stability, microstructure development, interfacial reactions, and volatility issues. Part III of the work investigated the stability of Ce-(Mn,Co)more » spinel coating, AISI441 metallic interconnect, alumina coating, and cell degradation. After 6000h of testing, the refractory sealing glass YSO77 (Ba-Sr-Y-B-Si) showed desirable chemical compatibility with YSZ electrolyte in that no discernable interfacial reaction was identified, consistent with thermodynamic calculations. In addition, no glass penetration into the thin electrolyte was observed. At the aluminized AISI441 interface, the protective alumina coating appeared to be corroded by the sealing glass. Air side interactions appeared to be more severe than fuel side interactions. Metal species such as Cr, Mn, and Fe were detected in the glass, but were limited to the vicinity of the interface. No alkaline earth chromates were found at the air side. Volatility was also studied in a similar glass and weight loss in a wet reducing environment was determined. Using the steady-state volatility data, the life time (40,000h) weight loss of refractory sealing glass YSO77 was estimated to be less than 0.1 wt%.« less

SEAL FOR ROTATING SHAFT

DOEpatents

Coffman, R.T.

1957-12-10

A seal is described for a rotatable shaft that must highly effective when the shaft is not rotating but may be less effective while the shaft is rotating. Weights distributed about a sealing disk secured to the shaft press the sealing disk against a tubular section into which the shiilt extends, and whem the shaft rotates, the centrifugal forces on the weights relieve the pressurc of the sealing disk against the tubular section. This action has the very desirible result of minimizing the wear of the rotating disk due to contact with the tubular section, while affording maximum sealing action when it is needed.

High Pressure Rotary Shaft Sealing Mechanism

DOEpatents

Dietle, Lannie; Gobeli, Jeffrey D.

2001-05-08

A laterally translatable pressure staged rotary shaft sealing mechanism having a seal housing with a shaft passage therein being exposed to a fluid pressure P1 and with a rotary shaft being located within the shaft passage. At least one annular laterally translatable seal carrier is provided. First and second annular resilient sealing elements are supported in axially spaced relation by the annular seal carriers and have sealing relation with the rotary shaft. The seal housing and at least one seal carrier define a first pressure staging chamber exposed to the first annular resilient sealing element and a second pressure staging chamber located between and exposed to the first and second annular resilient sealing elements. A first fluid is circulated to the first pressure chamber at a pressure P1, and a second staging pressure fluid is circulated to the second pressure chamber at a fraction of pressure P1 to achieve pressure staging, cooling of the seals. Seal placement provides hydraulic force balancing of the annular seal carriers.

Toward an Improved Hypersonic Engine Seal

NASA Technical Reports Server (NTRS)

Dunlap, Patrick H., Jr.; Steinetz, Bruce M.; DeMange,Jeffrey J.; Taylor, Shawn C.

2003-01-01

High temperature, dynamic seals are required in advanced engines to seal the perimeters of movable engine ramps for efficient, safe operation in high heat flux environments at temperatures from 2000 to 2500 F. Current seal designs do not meet the demanding requirements for future engines, so NASA s Glenn Research Center (GRC) is developing advanced seals to overcome these shortfalls. Two seal designs and two types of seal preloading devices were evaluated in a series of compression tests at room temperature and 2000 F and flow tests at room temperature. Both seals lost resiliency with repeated load cycling at room temperature and 2000 F, but seals with braided cores were significantly more flexible than those with cores composed of uniaxial ceramic fibers. Flow rates for the seals with cores of uniaxial fibers were lower than those for the seals with braided cores. Canted coil springs and silicon nitride compression springs showed promise conceptually as potential seal preloading devices to help maintain seal resiliency.

Shaft/shaft-seal interface characteristics of a multiple disk centrifugal blood pump.

PubMed

Manning, K B; Miller, G E

1999-06-01

A multiple disk centrifugal pump (MDCP) is under investigation as a potential left ventricular assist device. As is the case with most shaft driven pumps, leakage problems around the shaft/shaft seal interface are of major interest. If leakage were to occur during or after implantation, potential events such as blood loss, clotting, blood damage, and/or infections might result in adverse effects for the patient. Because these effects could be quite disastrous, potential shaft and shaft seal materials have been investigated to determine the most appropriate course to limit these effects. Teflon and nylon shaft seals were analyzed as potential candidates along with a stainless steel shaft and a Melonite coated shaft. The materials and shafts were evaluated under various time durations (15, 30, 45, and 60 min), motor speeds (800, 1,000, 1,200, and 1,400 rpm), and outer diameters (1/2 and 3/4 inches). The motor speed and geometrical configurations were typical for the MDCP under normal physiologic conditions. An air and water study was conducted to analyze the inner diameter wear, the inner temperature values, and the outer temperature values. Statistical comparisons were computed for the shaft seal materials, the shafts, and the outer diameters along with the inner and outer temperatures. The conclusions made from the results indicate that both the tested shaft seal materials and shaft materials are not ideal candidates to be used for the MDCP. Teflon experienced a significant amount of wear in air and water studies. Nylon did experience little wear, but heat generation was an evident problem. A water study on nylon was not conducted because of its molecular structure.

Ferrules seals

DOEpatents

Smith, J.L.

1984-07-10

A device is provided for sealing an inner tube and an outer tube without excessively deforming the tubes. The device includes two ferrules which cooperate to form a vacuum-tight seal between the inner tube and outer tube and having mating surfaces such that overtightening is not possible. 3 figs.

A magnetic fluid seal for rotary blood pumps: effects of seal structure on long-term performance in liquid.

PubMed

Mitamura, Yoshinori; Takahashi, Sayaka; Amari, Shuichi; Okamoto, Eiji; Murabayashi, Shun; Nishimura, Ikuya

2011-03-01

A magnetic fluid (MF) seal enables mechanical contact-free rotation of the shaft and hence has excellent durability. The performance of an MF seal, however, has been reported to decrease in liquids. We developed an MF seal that has a "shield" mechanism, and a new MF with a higher magnetization of 47.9 kA/m. The sealing performance of the MF seal installed in a rotary blood pump was studied. Three types of MF seals were used. Seal A was a conventional seal without a shield. Seal B had the same structure as that of Seal A, but the seal was installed at 1 mm below liquid level. Seal C was a seal with a shield and the MF was set at 1 mm below liquid level. Seal A failed after 6 and 11 days. Seal B showed better results (20 and 73 days). Seal C showed long-term durability (217 and 275 days). The reason for different results in different seal structures was considered to be different flow conditions near the magnetic fluid. Fluid dynamics near the MF in the pump were analyzed using computational fluid dynamics (CFD) software. We have developed an MF seal with a shield that works in liquid for >275 days. The MF seal is promising as a shaft seal for rotary blood pumps.

Heat sealable, flame and abrasion resistant coated fabric. [clothing and containers for space exploration

NASA Technical Reports Server (NTRS)

Tschirch, R. P.; Sidman, K. R. (Inventor)

1981-01-01

Flame retardant, abrasion resistant elastomeric compositions are comprised of thermoplastic polyurethane polymer and flame retarding amounts of a filler selected from decabromodiphenyloxide and antimony oxide in a 3:1 weight ratio, and decabromodiphenyloxide, antimony oxide, and ammonium polyphosphate in a 3:1:3 weight ratio respectively. Coated fabrics employing such elastomeric compositions as coating film are flexible, lightweight, and air impermeable and can be made using heat or dielectric sealing procedures.

Why do seals have cones? Behavioural evidence for colour-blindness in harbour seals.

PubMed

Scholtyssek, Christine; Kelber, Almut; Dehnhardt, Guido

2015-03-01

All seals and cetaceans have lost at least one of two ancestral cone classes and should therefore be colour-blind. Nevertheless, earlier studies showed that these marine mammals can discriminate colours and a colour vision mechanism has been proposed which contrasts signals from cones and rods. However, these earlier studies underestimated the brightness discrimination abilities of these animals, so that they could have discriminated colours using brightness only. Using a psychophysical discrimination experiment, we showed that a harbour seal can solve a colour discrimination task by means of brightness discrimination alone. Performing a series of experiments in which two harbour seals had to discriminate the brightness of colours, we also found strong evidence for purely scotopic (rod-based) vision at light levels that lead to mesopic (rod-cone-based) vision in other mammals. This finding speaks against rod-cone-based colour vision in harbour seals. To test for colour-blindness, we used a cognitive approach involving a harbour seal trained to use a concept of same and different. We tested this seal with pairs of isoluminant stimuli that were either same or different in colour. If the seal had perceived colour, it would have responded to colour differences between stimuli. However, the seal responded with "same", providing strong evidence for colour-blindness.

Borehole sealing method and apparatus

DOEpatents

Hartley, James N.; Jansen, Jr., George

1977-01-01

A method and apparatus is described for sealing boreholes in the earth. The borehole is blocked at the sealing level, and a sealing apparatus capable of melting rock and earth is positioned in the borehole just above seal level. The apparatus is heated to rock-melting temperature and powdered rock or other sealing material is transported down the borehole to the apparatus where it is melted, pooling on the mechanical block and allowed to cool and solidify, sealing the hole. Any length of the borehole can be sealed by slowly raising the apparatus in the borehole while continuously supplying powdered rock to the apparatus to be melted and added to the top of the column of molten and cooling rock, forming a continuous borehole seal. The sealing apparatus consists of a heater capable of melting rock, including means for supplying power to the heater, means for transporting powdered rock down the borehole to the heater, means for cooling the apparatus and means for positioning the apparatus in the borehole.

Biofouling of Cr-Nickel Spray Coated Films on Steel Surfaces

NASA Astrophysics Data System (ADS)

Yoshida, Kento; Kanematsu, Hideyuki; Kuroda, Daisuke; Ikigai, Hajime; Kogo, Takeshi; Yokoyama, Seiji

2012-03-01

Nowadays, corrosion of metals brings us serious economic loss and it often reaches several percentage of GNP. Particularly the marine corrosion was serious and the counter measure was very hard to be established, since the number of factors is huge and complicated. One of the complicated factors in marine corrosion is biofouling. Biofouling was classified into two main categories, microfouling and macrofouling. The former is composed of biofilm formation mainly. Marine bacteria are attached to material surfaces, seeking for nutrition in oligotrophic environment and they excrete polysaccharide to form biofilm on metal surfaces. Then larger living matters are attached on the biofilms to develop biofouling on metal surfaces, which often lead loss and failures of metals in marine environments. From the viewpoint of corrosion protection and maintenance of marine structures, biofouling should be mitigated as much as possible. In this study, we applied spray coating to steels and investigated if chromium-nickel spray coating could mitigate the biofouling, being compared with the conventional aluminium-zinc spray coating in marine environments. The specimens used for this investigation are aluminium, zinc, aluminium-zinc, stacked chromium/nickel and those films were formed on carbon steel (JIS SS400). And the pores formed by spray coating were sealed by a commercial reagent for some specimens. All of those specimens were immersed into sea water located at Marina Kawage (854-3, Chisato, Tsu, Mie Prefecture) in Ise Bay for two weeks. The depth of the specimen was two meter from sea water surface and the distance was always kept constant, since they were suspended from the floating pier. The temperature in sea water changed from 10 to 15 degrees Celsius during the immersion test. The biofouling behavior was investigated by low vacuum SEM (Hitachi Miniscope TM1000) and X-ray fluorescent analysis. When the spray coated specimens with and without sealing agents were compared

Static seal for turbine engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salazar, Santiago; Gisch, Andrew

2014-04-01

A seal structure for a gas turbine engine, the seal structure including first and second components located adjacent to each other and forming a barrier between high and low pressure zones. A seal cavity is defined in the first and second components, the seal cavity extending to either side of an elongated gap extending generally in a first direction between the first and second components. A seal member is positioned within the seal cavity and spans across the elongated gap. The seal member includes first and second side edges extending into each of the components in a second direction transversemore » to the first direction, and opposing longitudinal edges extending between the side edges generally parallel to the first direction. The side edges include a groove formed therein for effecting a reduction of gas flow around the seal member at the side edges.« less

Security seal. [Patent application

DOEpatents

Gobeli, G.W.

1981-11-17

Security for a package or verifying seal in plastic material is provided by a print seal with unique thermally produced imprints in the plastic. If tampering is attempted, the material is irreparably damaged and thus detectable. The pattern of the imprints, similar to fingerprints are recorded as a positive identification for the seal, and corresponding recordings made to allow comparison. The integrity of the seal is proved by the comparison of imprint identification records made by laser beam projection.

Brush seals for cryogenic applications

NASA Astrophysics Data System (ADS)

Proctor, Margaret P.

1994-07-01

This viewgraph presentation presents test results of brush seals for cryogenic applications. Leakage for a single brush seal was two to three times less than for a 12-tooth labyrinth seal. The maximum temperature rise for a single brush seal was less than 50 R and occurred at 25 psid across the seal and 35,000 rpm. A static blowout test demonstrated sealing capability up to 550 psid. The seal limit was not obtained. The power loss for a single brush at 35,000 rpm and 175 psid was 2.45 hp. Two brushes far apart leak less than two brushes tight packed. Rotor wear was approximately 0.00075 mils and bristle wear was 1-3 mils after 4-1/2 hours.

Characteristics of PAH tar oil contaminated soils-Black particles, resins and implications for treatment strategies.

PubMed

Trellu, Clément; Miltner, Anja; Gallo, Rosita; Huguenot, David; van Hullebusch, Eric D; Esposito, Giovanni; Oturan, Mehmet A; Kästner, Matthias

2017-04-05

Tar oil contamination is a major environmental concern due to health impacts of polycyclic aromatic hydrocarbons (PAH) and the difficulty of reaching acceptable remediation end-points. Six tar oil-contaminated soils with different industrial histories were compared to investigate contamination characteristics by black particles. Here we provide a simple method tested on 6 soils to visualize and identify large amounts of black particles (BP) as either solid aggregates of resinified and weathered tar oil or various wood/coke/coal-like materials derived from the contamination history. These materials contain 2-10 times higher PAH concentrations than the average soil and were dominantly found in the sand fraction containing 42-86% of the total PAH. The PAH contamination in the different granulometric fractions was directly proportional to the respective total organic carbon content, since the PAH were associated to the carbonaceous particulate materials. Significantly lower (bio)availability of PAH associated to these carbonaceous phases is widely recognized, thus limiting the efficiency of remediation techniques. We provide a conceptual model of the limited mass transfer of PAH from resinated tar oil phases to the water phase and emphasize the options to physically separate BP based on their lower bulk density and slower settling velocity. Copyright © 2017 Elsevier B.V. All rights reserved.

Stabilizing geometry for hydrodynamic rotary seals

DOEpatents

Dietle, Lannie L.; Schroeder, John E.

2010-08-10

A hydrodynamic sealing assembly including a first component having first and second walls and a peripheral wall defining a seal groove, a second component having a rotatable surface relative to said first component, and a hydrodynamic seal comprising a seal body of generally ring-shaped configuration having a circumference. The seal body includes hydrodynamic and static sealing lips each having a cross-sectional area that substantially vary in time with each other about the circumference. In an uninstalled condition, the seal body has a length defined between first and second seal body ends which varies in time with the hydrodynamic sealing lip cross-sectional area. The first and second ends generally face the first and second walls, respectively. In the uninstalled condition, the first end is angulated relative to the first wall and the second end is angulated relative to the second wall. The seal body has a twist-limiting surface adjacent the static sealing lip. In the uninstalled condition, the twist-limiting surface is angulated relative to the peripheral wall and varies along the circumference. A seal body discontinuity and a first component discontinuity mate to prevent rotation of the seal body relative to the first component.

Aspects of tar sands development in Nigeria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adewusi, V.A.

1992-07-01

Development of Nigerian massive reserves of crude bitumen and associated heavy oil is imminent in view of the impacts that the huge importation of these materials and their products have on the nation's economy, coupled with the depleting reserves of Nigeria and highlights the appropriate production technology options and their environmental implications. The utilization potentials of these resources are also enumerated, as well as the government's role in achieving accelerated, long-term tar sands development in the country.

Sealing properties of mechanical seals for an axial flow blood pump.

PubMed

Tomioka, J; Mori, T; Yamazaki, K; Koyanagi, H

1999-08-01

A miniature intraventricular axial flow blood pump for left ventricular support is under development. One of the key technologies required for such pumps is sealing of the motor shaft. In this study, to prevent blood backflow into the motor side, mechanical seals were developed and their sealing properties investigated. In the experimental apparatus, the mechanical seal separated the bovine blood on the chamber side from the cooling water on the motor side. A leakage of the blood was measured by inductively coupled plasma (ICP) light emission analysis. The rate of hemolysis was measured by the cyanmethemoglobin method. Frictional torque acting on the shaft was measured by a torque transducer. In the experiments, the rotational speed of the shaft was changed from 1,000 to 10,000 rpm, and the contact force of the seal faces was changed from 1.96 to 4.31 N. To estimate lubrication regimes, the Stribeck curve, a diagram of the coefficient of friction against the bearing characteristic G number, was drawn. The results of the experiments showed that both the leakage of blood and the rate of hemolysis were very small. The friction loss was also very small. The mechanical seal was operated in various lubrication regimes, from a fluid lubrication regime to a mixed lubrication regime.

Rim seal arrangement having pumping feature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Ching-Pang; Myers, Caleb

A rim seal arrangement for a gas turbine engine includes a first seal face on a rotor component, and a second seal face on a stationary annular rim centered about a rotation axis of the rotor component. The second seal face is spaced from the first seal face along an axial direction to define a seal gap. The seal gap is located between a radially outer hot gas path and a radially inner rotor cavity. The first seal face has a plurality of circumferentially spaced depressions, each having a depth in an axial direction and extending along a radial extentmore » of the first seal face. The depressions influence flow in the seal gap such that during rotation of the rotor component, fluid in the seal gap is pumped in a radially outward direction to prevent ingestion of a gas path fluid from the hot gas path into the rotor cavity.« less

Advances in Thermal Spray Coatings for Gas Turbines and Energy Generation: A Review

NASA Astrophysics Data System (ADS)

Hardwicke, Canan U.; Lau, Yuk-Chiu

2013-06-01

Functional coatings are widely used in energy generation equipment in industries such as renewables, oil and gas, propulsion engines, and gas turbines. Intelligent thermal spray processing is vital in many of these areas for efficient manufacturing. Advanced thermal spray coating applications include thermal management, wear, oxidation, corrosion resistance, sealing systems, vibration and sound absorbance, and component repair. This paper reviews the current status of materials, equipment, processing, and properties' aspects for key coatings in the energy industry, especially the developments in large-scale gas turbines. In addition to the most recent industrial advances in thermal spray technologies, future technical needs are also highlighted.

Remediation of Coal Tar by STAR: Self-Sustaining Propagation Across Clean Gaps

NASA Astrophysics Data System (ADS)

Gerhard, J.; Brown, J.; Torero, J. L.; Grant, G.

2016-12-01

Self-sustaining Treatment for Active Remediation (STAR) is an emerging remediation technique which utilizes a subsurface smouldering reaction to destroy non-aqueous phase liquids (NAPL) in situ. The reaction is self-sustaining in that, once ignited, the destructive smouldering front will propagate outwards using only the energy embedded in the contaminant. However, it is known that coal tar can occur as both a continuous pool as well as in distinct seams separated by clean intervals. This study evaluated the hypothesis that the smouldering reaction can cross or `jump' clean gaps by transferring enough heat through the gap to re-ignite the reaction in the contaminated region beyond. Column and 2D box experiments were performed at two scales to determine the maximum clean gap which could be jumped vertically and horizontally. Once the maximum gap had been determined, sensitivity to various in situ and engineering control parameters were explored including: coal tar layer thickness, soil permeability, moisture content, NAPL saturation, and air injection flowrate. High resolution thermocouples informed the progress of the reaction, continuous gas emissions analysis revealed when the reaction was active and dormant, and detailed excavation mapped the extent of remediation and whether gaps were successfully jumped. The work demonstrated that substantial clean gaps, approaching the limit of the laboratory scale, can be jumped by the smouldering reaction using convective heat transfer. Also observed in some cases was the mobilization of pre-heated coal tar into the clean gaps and the reaction's ability to propagate through and destroy coal tar both adjacent to and within the gaps. This work is providing new insights into the robust nature of the technology for in situ applications, and indicating how extreme the heterogeneity has to be before the reaction is interrupted and a new ignition location would be required.

Regenerator cross arm seal assembly

DOEpatents

Jackman, Anthony V.

1988-01-01

A seal assembly for disposition between a cross arm on a gas turbine engine block and a regenerator disc, the seal assembly including a platform coextensive with the cross arm, a seal and wear layer sealingly and slidingly engaging the regenerator disc, a porous and compliant support layer between the platform and the seal and wear layer porous enough to permit flow of cooling air therethrough and compliant to accommodate relative thermal growth and distortion, a dike between the seal and wear layer and the platform for preventing cross flow through the support layer between engine exhaust and pressurized air passages, and air diversion passages for directing unregenerated pressurized air through the support layer to cool the seal and wear layer and then back into the flow of regenerated pressurized air.

Tar Creek study, Sargent oil field, Santa Clara County, California

USGS Publications Warehouse

Wagner, David L.; Fedasko, Bill; Carnahan, J.R.; Brunetti, Ross; Magoon, Leslie B.; Lillis, Paul G.; Lorenson, T.D.; Stanley, Richard G.

2002-01-01

Field work in the Tar Creek area of Sargent oil field was performed June 26 to 28, 2000. The Santa Clara County study area is located in Sections, 30, 31, and 32, Township 11 South, Range 4 East, M.D.B&M; and in Sections 25 and 36, Township 11 South, Range 3 East, M.D.B.&M., north and south of Tar Creek, west of Highway 101. The work was a cooperative effort of the California Department of Conservation's Division of Oil, Gas, and Geothermal Resources (DOGGR), California Geological Survey (CGS), and the United States Geological Survey (USGS). The purpose of the project was to map the stratigraphy and geologic structure (David Wagner, CGS); sample oil for age dating (Les Magoon, USGS); and search for undocumented wells plus conduct a GPS survey of the area (Bill Fedasko, J.P. Carnahan, and Ross Brunetti, DOGGR)

Coal-tar pavement sealants might substantially increase children's PAH exposures

USGS Publications Warehouse

Williams, E. Spencer; Mahler, Barbara J.; Van Metre, Peter C.

2012-01-01

Dietary ingestion has been identified repeatedly as the primary route of human exposure to polycyclic aromatic hydrocarbons (PAHs), seven of which are classified as probable human carcinogens (B2 PAHs) by the U.S. EPA. Humans are exposed to PAHs through ingestion of cooked and uncooked foods, incidental ingestion of soil and dust, inhalation of ambient air, and absorption through skin. Although PAH sources are ubiquitous in the environment, one recently identified PAH source stands out: Coal-tar-based pavement sealant—a product applied to many parking lots, driveways, and even playgrounds primarily in the central, southern, and eastern U.S.—has PAH concentrations 100–1000 times greater than most other PAH sources. It was reported recently that PAH concentrations in house dust in residences adjacent to parking lots with coal-tar-based sealant were 25 times higher than in residences adjacent to unsealed asphalt parking lots.

Nuclear instrumentation cable end seal

DOEpatents

Cannon, Collins P.; Brown, Donald P.

1979-01-01

An improved coaxial end seal for hermetically sealed nuclear instrumentation cable exhibiting an improved breakdown pulse noise characteristic under high voltage, high temperature conditions. A tubular insulator body has metallized interior and exterior surface portions which are braze sealed to a center conductor and an outer conductive sheath. The end surface of the insulator body which is directed toward the coaxial cable to which it is sealed has a recessed surface portion within which the braze seal material terminates.

Membrane Switches Check Seal Pressure

NASA Technical Reports Server (NTRS)

Hodgetts, P. J.; Stuckenberg, F. H.; Morrissey, E. T.

1984-01-01

Array of flexible membrane switches used to indicate closure of seal. Switch membrane responds to pressure exerted by rigid surface on compliant sealing medium and provides switch contacts monitored electronically. Membrane switches connected in series and placed under seal. When all switches are closed lamp or LED lights up, indicating requisite seal pressure has been realized at all switch positions. Principle used to ensure integrity of seals on refrigerator and oven doors, weatherstripping, hatches, spacecraft, airplanes, and submarines.

Seal system with integral detector

DOEpatents

Fiarman, Sidney

1985-01-01

There is disclosed a seal system for materials where security is of the essence, such as nuclear materials, which is tamper-indicating, which indicates changes in environmental conditions that evidence attempts to by-pass the seal, which is unique and cost effective, said seal system comprised of a seal where an optical signal is transmitted through a loop, with a detector to read said signal, and one or more additional detectors designed to detect environmental changes, these detectors being operatively associated with the seal so that detection of a break in the optical signal or detection of environmental changes will cause an observable change in the seal.