The NOvA Technical Design Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ayres, D.S.; Drake, G.R.; Goodman, M.C.

Technical Design Report (TDR) describes the preliminary design of the NOvA accelerator upgrades, NOvA detectors, detector halls and detector sites. Compared to the March 2006 and November 2006 NOvA Conceptual Design Reports (CDR), critical value engineering studies have been completed and the alternatives still active in the CDR have been narrowed to achieve a preliminary technical design ready for a Critical Decision 2 review. Many aspects of NOvA described this TDR are complete to a level far beyond a preliminary design. In particular, the access road to the NOvA Far Detector site in Minnesota has an advanced technical design atmore » a level appropriate for a Critical Decision 3a review. Several components of the accelerator upgrade and new neutrino detectors also have advanced technical designs appropriate for a Critical Decision 3a review. Chapter 1 is an Executive Summary with a short description of the NOvA project. Chapter 2 describes how the Fermilab NuMI beam will provide a narrow band beam of neutrinos for NOvA. Chapter 3 gives an updated overview of the scientific basis for the NOvA experiment, focusing on the primary goal to extend the search for {nu}{sub {mu}} {yields} {nu}{sub e} oscillations and measure the sin{sup 2}(2{theta}{sub 13}) parameter. This parameter has not been measured in any previous experiment and NOvA would extend the search by about an order of magnitude beyond the current limit. A secondary goal is to measure the dominant mode oscillation parameters, sin{sup 2}(2{theta}{sub 23}) and {Delta}m{sub 32}{sup 2} to a more precise level than previous experiments. Additional physics goals for NOvA are also discussed. Chapter 4 describes the Scientific Design Criteria which the Fermilab accelerator complex, NOvA detectors and NOvA detector sites must satisfy to meet the physics goals discussed in Chapter 3. Chapter 5 is an overview of the NOvA project. The changes in the design relative to the NOvA CDR are discussed. Chapter 6 summarizes

The Roles of Technical Communication Researchers in Design Scholarship

ERIC Educational Resources Information Center

Sánchez, Fernando

2017-01-01

Design has come to be understood as an essential aspect of the work that technical communicators claim. As a result, research in the field of technical communication has approached studies of design in numerous ways. This article showcases how technical communication researchers assume the roles of observers, testers, critics, creators, and…

Metric Conversion in the Construction Industries--Technical Issues and Status.

ERIC Educational Resources Information Center

Milton, Hans J.; Berry, Sandra A.

This Special Publication was prepared at the request of the Metric Symposium Planning Committee of the National Institute of Building Sciences (NIBS). It is intended to provide information on technical issues and status of metric conversion in the United States construction industries. It was made available to attendees at the NIBS Symposium on…

Employers' Perception of Graduates with Entry-Level Technical Skills from Construction Industry Programs in Ghana and Nigeria

ERIC Educational Resources Information Center

Acheampong, Philip

2013-01-01

The purpose of this comparative study was to identify the technical skills and abilities needed by prospective employees of construction industries in Ghana and Nigeria. Potential employees were defined here as recent graduates of construction industry programs with entry-level technical skills. The continuous growth in and expansion of these two…

Design and construction of a prototype ACTS propagation terminal

NASA Technical Reports Server (NTRS)

Stutzman, Warren; Pratt, Tim; Nunnally, Charles; Nealy, Randall; Remaklus, Will; Sylvester, Bill; Predoehl, Andrew; Gaff, Doug

1993-01-01

The launch schedule for the Advanced Communication Technology Satellite (ACTS) spacecraft did not leave sufficient time for completion of the prototype ACTS Propagation Terminals (APT) prior to initiation of the APT production phase. In fact, the approach used was to construct and test all subassemblies of the terminal with special emphasis on the technically challenging portions. These include the RF front end that uses a state-of-the-art down converter which integrates a low noise amplifier, mixer, post amplifier, filter, and local oscillator port frequency doubler into a single small package. In addition, a new digital receiver that uses the latest DSP technology was developed. Both of these subassemblies were thoroughly tested. The highest risk technology in the APT program was the digital receiver. Several candidate algorithms and DSP chips were investigated early on, primarily under JPL sponsorship. A receiver was constructed based on Texas Instruments chip. The final prototype digital receiver was one based on an Analog Devices chip. The design and test results are documented in a report prepared for this grant. A Primary Design Review (PDR) was conducted 30 May 1991, and a Critical Design Review was held 7 Jul. 1992. Final complete documentation of the APT's will appear in the form of three reports: a hardware description report, a report on the data collection code (ACTS VIEW), and a report on the preprocessing code.

The International Linear Collider Technical Design Report - Volume 1: Executive Summary

DOE Office of Scientific and Technical Information (OSTI.GOV)

Behnke, Ties; Brau, James E.; Foster, Brian

2013-06-26

The International Linear Collider Technical Design Report (TDR) describes in four volumes the physics case and the design of a 500 GeV centre-of-mass energy linear electron-positron collider based on superconducting radio-frequency technology using Niobium cavities as the accelerating structures. The accelerator can be extended to 1 TeV and also run as a Higgs factory at around 250 GeV and on the Z0 pole. A comprehensive value estimate of the accelerator is give, together with associated uncertainties. It is shown that no significant technical issues remain to be solved. Once a site is selected and the necessary site-dependent engineering is carriedmore » out, construction can begin immediately. The TDR also gives baseline documentation for two high-performance detectors that can share the ILC luminosity by being moved into and out of the beam line in a "push-pull" configuration. These detectors, ILD and SiD, are described in detail. They form the basis for a world-class experimental programme that promises to increase significantly our understanding of the fundamental processes that govern the evolution of the Universe.« less

Design and construction of a 76m long-travel laser enclosure for a space occulter testbed

NASA Astrophysics Data System (ADS)

Galvin, Michael; Kim, Yunjong; Kasdin, N. Jeremy; Sirbu, Dan; Vanderbei, Robert; Echeverri, Dan; Sagolla, Giuseppe; Rousing, Andreas; Balasubramanian, Kunjithapatham; Ryan, Daniel; Shaklan, Stuart; Lisman, Doug

2016-07-01

Princeton University is upgrading our space occulter testbed. In particular, we are lengthening it to 76m to achieve flightlike Fresnel numbers. This much longer testbed required an all-new enclosure design. In this design, we prioritized modularity and the use of commercial off-the-shelf (COTS) and semi-COTS components. Several of the technical challenges encountered included an unexpected slow beam drift and black paint selection. Herein we describe the design and construction of this long-travel laser enclosure.

LUX-ZEPLIN (LZ) Technical Design Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mount, B. J.

In this Technical Design Report (TDR) we describe the LZ detector to be built at the Sanford Underground Research Facility (SURF). The LZ dark matter experiment is designed to achieve sensitivity to a WIMP-nucleon spin-independent cross section of three times ten to the negative forty-eighth square centimeters.

Launch Vehicle Design Process: Characterization, Technical Integration, and Lessons Learned

NASA Technical Reports Server (NTRS)

Blair, J. C.; Ryan, R. S.; Schutzenhofer, L. A.; Humphries, W. R.

2001-01-01

Engineering design is a challenging activity for any product. Since launch vehicles are highly complex and interconnected and have extreme energy densities, their design represents a challenge of the highest order. The purpose of this document is to delineate and clarify the design process associated with the launch vehicle for space flight transportation. The goal is to define and characterize a baseline for the space transportation design process. This baseline can be used as a basis for improving effectiveness and efficiency of the design process. The baseline characterization is achieved via compartmentalization and technical integration of subsystems, design functions, and discipline functions. First, a global design process overview is provided in order to show responsibility, interactions, and connectivity of overall aspects of the design process. Then design essentials are delineated in order to emphasize necessary features of the design process that are sometimes overlooked. Finally the design process characterization is presented. This is accomplished by considering project technical framework, technical integration, process description (technical integration model, subsystem tree, design/discipline planes, decision gates, and tasks), and the design sequence. Also included in the document are a snapshot relating to process improvements, illustrations of the process, a survey of recommendations from experienced practitioners in aerospace, lessons learned, references, and a bibliography.

Crew Transportation Technical Standards and Design Evaluation Criteria

NASA Technical Reports Server (NTRS)

Lueders, Kathryn L.; Thomas, Rayelle E. (Compiler)

2015-01-01

Crew Transportation Technical Standards and Design Evaluation Criteria contains descriptions of technical, safety, and crew health medical processes and specifications, and the criteria which will be used to evaluate the acceptability of the Commercial Providers' proposed processes and specifications.

Experimental evaluation and design of unfilled and concrete-filled FRP composite piles : Task 4B : material & construction specifications : final report.

DOT National Transportation Integrated Search

2015-07-01

The overall goal of this project is the experimental evaluation and design of unfilled and concrete-filled FRP composite piles for load-bearing in bridges. This report covers Task 4B, Materials and Construction Specifications. : This technical report...

Virtual design and construction of plumbing systems

NASA Astrophysics Data System (ADS)

Filho, João Bosco P. Dantas; Angelim, Bruno Maciel; Guedes, Joana Pimentel; de Castro, Marcelo Augusto Farias; Neto, José de Paula Barros

2016-12-01

Traditionally, the design coordination process is carried out by overlaying and comparing 2D drawings made by different project participants. Detecting information errors from a composite drawing is especially challenging and error prone. This procedure usually leaves many design errors undetected until construction begins, and typically lead to rework. Correcting conflict issues, which were not identified during design and coordination phase, reduces the overall productivity for everyone involved in the construction process. The identification of construction issues in the field generate Request for Information (RFIs) that is one of delays causes. The application of Virtual Design and Construction (VDC) tools to the coordination processes can bring significant value to architecture, structure, and mechanical, electrical, and plumbing (MEP) designs in terms of a reduced number of errors undetected and requests for information. This paper is focused on evaluating requests for information (RFI) associated with water/sanitary facilities of a BIM model. Thus, it is expected to add improvements of water/sanitary facility designs, as well as to assist the virtual construction team to notice and identify design problems. This is an exploratory and descriptive research. A qualitative methodology is used. This study adopts RFI's classification in six analyzed categories: correction, omission, validation of information, modification, divergence of information and verification. The results demonstrate VDC's contribution improving the plumbing system designs. Recommendations are suggested to identify and avoid these RFI types in plumbing system design process or during virtual construction.

24 CFR 941.203 - Design and construction standards.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 4 2011-04-01 2011-04-01 false Design and construction standards... URBAN DEVELOPMENT PUBLIC HOUSING DEVELOPMENT PHA Eligibility and Program Requirements § 941.203 Design and construction standards. (a) Physical structures shall be designed, constructed and equipped so as...

Technical Handbook for Facilities Engineering and Construction Manual, Part 2: Federally Assisted Activities. Guide for Project Applicants-Construction Management Services. Department Technical Handbook Series.

ERIC Educational Resources Information Center

Department of Health , Education, and Welfare, Washington., DC. Office of the Secretary.

This handbook provides a basis for consideration of acceptable approaches which are available and may be used to initiate the use of construction management services in the planning, design, and construction of federally assisted construction projects. It includes the mandatory federal requirements as well as acceptable procedures for selecting…

Handling the Difficulties of Technical School Students in the Construction and Interpretation of Graphic Representations

ERIC Educational Resources Information Center

Marinos, Andreas

2010-01-01

In this work, an attempt is made to evaluate the errors that have to do with the interpretation and construction of graphic representations. Although the students are studying in the second year of technical high school (secondary education), i.e. in schools with an emphasis in technical subjects (post junior secondary), it is observed that they…

29 CFR 1926.1433 - Design, construction and testing.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 29 Labor 8 2013-07-01 2013-07-01 false Design, construction and testing. 1926.1433 Section 1926... Construction § 1926.1433 Design, construction and testing. The following requirements apply to equipment that... locomotive cranes manufactured prior to November 8, 2010 must meet the applicable requirements for design...

29 CFR 1926.1433 - Design, construction and testing.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 8 2014-07-01 2014-07-01 false Design, construction and testing. 1926.1433 Section 1926... Construction § 1926.1433 Design, construction and testing. The following requirements apply to equipment that... locomotive cranes manufactured prior to November 8, 2010 must meet the applicable requirements for design...

29 CFR 1926.1433 - Design, construction and testing.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 8 2011-07-01 2011-07-01 false Design, construction and testing. 1926.1433 Section 1926... Construction § 1926.1433 Design, construction and testing. The following requirements apply to equipment that... locomotive cranes manufactured prior to November 8, 2010 must meet the applicable requirements for design...

29 CFR 1926.1433 - Design, construction and testing.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 29 Labor 8 2012-07-01 2012-07-01 false Design, construction and testing. 1926.1433 Section 1926... Construction § 1926.1433 Design, construction and testing. The following requirements apply to equipment that... locomotive cranes manufactured prior to November 8, 2010 must meet the applicable requirements for design...

Construction Surveying, 3-27. Military Curriculum Materials for Vocational and Technical Education.

ERIC Educational Resources Information Center

Ohio State Univ., Columbus. National Center for Research in Vocational Education.

This short course on construction surveying was developed from military curriculum materials for use in technical and vocational education programs. Students completing the course should be able to perform engineering surveys related to area and route surveying (knowledge of basic survey techniques is a prerequisite). The course is divided into…

7 CFR 1780.54 - Technical services.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., Constructing and Inspections § 1780.54 Technical services. Owners are responsible for providing the engineering, architect and environmental services necessary for planning, designing, bidding, contracting, inspecting...

18 CFR 2.13 - Design and construction.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 18 Conservation of Power and Water Resources 1 2011-04-01 2011-04-01 false Design and construction... Interpretations Under the Federal Power Act § 2.13 Design and construction. (a) The Commission recognizes the... for the Protection of Natural, Historic, Scenic, and Recreational Values in the Design and Location of...

Constructing a modern cytology laboratory: A toolkit for planning and design.

PubMed

Roberson, Janie; Wrenn, Allison; Poole, John; Jaeger, Andrew; Eltoum, Isam A

2013-01-01

Constructing or renovating a laboratory can be both challenging and rewarding. UAB Cytology (UAB CY) recently undertook a project to relocate from a building constructed in 1928 to new space. UAB CY is part of an academic center that provides service to a large set of patients, support training of one cytotechnology program and one cytopathology fellowship training program and involve actively in research and scholarly activity. Our objectives were to provide a safe, aesthetically pleasing space and gain efficiencies through lean processes. The phases of any laboratory design project are Planning, Schematic Design (SD), Design Development (DD), Construction Documents (CD) and Construction. Lab personnel are most critical in the Planning phase. During this time stakeholders, relationships, budget, square footage and equipment were identified. Equipment lists, including what would be relocated, purchased new and projected for future growth ensure that utilities were matched to expected need. A chemical inventory was prepared and adequate storage space was planned. Regulatory and safety requirements were discussed. Tours and high level process flow diagrams helped architects and engineers understand the laboratory daily work. Future needs were addressed through a questionnaire which identified potential areas of growth and technological change. Throughout the project, decisions were driven by data from the planning phase. During the SD phase, objective information from the first phase was used by architects and planners to create a general floor plan. This was the basis of a series of meetings to brainstorm and suggest modifications. DD brings more detail to the plans with engineering, casework, equipment specifics, finishes. Design changes should be completed at this phase. The next phase, CD took the project from the lab purview into purely technical mode. Construction documents were used by the contractor for the bidding process and ultimately the Construction

Using Design Principles to Teach Technical Communication.

ERIC Educational Resources Information Center

Markel, Mike

1995-01-01

Compares the writing of two students--a competent writer and a weak one--in a technical communication course before and after discussion of design principles. Finds that a basic understanding of design principles helped them improve document macrostructure but had little effect on document microstructure. Suggests that integrating document design…

Energy efficiency in light-frame wood construction

Treesearch

Gerald E. Sherwood; Gunard Hans

1979-01-01

This report presents information needed for design and construction of energy-efficient light-frame wood structures. The opening section discusses improving the thermal performance of a house by careful planning and design. A second section of the report provides technical information on the thermal properties of construction materials, and on the basic engineering...

Technical data for concentrated solar power plants in operation, under construction and in project.

PubMed

Pelay, Ugo; Luo, Lingai; Fan, Yilin; Stitou, Driss; Rood, Mark

2017-08-01

This article presents technical data for concentrated solar power (CSP) plants in operation, under construction and in project all over the world in the form of tables. These tables provide information about plants (e.g., name of the CSP plant, country of construction, owner of the plant, aim of the plant) and their technical characteristics (e.g., CSP technology, solar power, area of the plant, presence and type of hybridization system, electricity cost, presence and type of TES, power cycle fluid, heat transfer fluid, operating temperature, operating pressure, type of turbine, type and duration of storage, etc.). Further interpretation of the data and discussions on the current state-of-the-art and future trends of CSP can be found in the associated research article (Pelay et al., 2017) [1].

48 CFR 801.602-80 - Legal and technical review-Office of Construction and Facilities Management and National Cemetery...

Code of Federal Regulations, 2012 CFR

2012-10-01

...-Office of Construction and Facilities Management and National Cemetery Administration. 801.602-80 Section... Responsibilities 801.602-80 Legal and technical review-Office of Construction and Facilities Management and National Cemetery Administration. An Office of Construction and Facilities Management or National Cemetery...

48 CFR 801.602-80 - Legal and technical review-Office of Construction and Facilities Management and National Cemetery...

Code of Federal Regulations, 2011 CFR

2011-10-01

...-Office of Construction and Facilities Management and National Cemetery Administration. 801.602-80 Section... Responsibilities 801.602-80 Legal and technical review-Office of Construction and Facilities Management and National Cemetery Administration. An Office of Construction and Facilities Management or National Cemetery...

48 CFR 801.602-80 - Legal and technical review-Office of Construction and Facilities Management and National Cemetery...

Code of Federal Regulations, 2013 CFR

2013-10-01

...-Office of Construction and Facilities Management and National Cemetery Administration. 801.602-80 Section... Responsibilities 801.602-80 Legal and technical review-Office of Construction and Facilities Management and National Cemetery Administration. An Office of Construction and Facilities Management or National Cemetery...

48 CFR 801.602-80 - Legal and technical review-Office of Construction and Facilities Management and National Cemetery...

Code of Federal Regulations, 2014 CFR

2014-10-01

...-Office of Construction and Facilities Management and National Cemetery Administration. 801.602-80 Section... Responsibilities 801.602-80 Legal and technical review-Office of Construction and Facilities Management and National Cemetery Administration. An Office of Construction and Facilities Management or National Cemetery...

19 CFR 115.30 - Technical requirements for containers by design type.

Code of Federal Regulations, 2011 CFR

2011-04-01

... SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.30 Technical... 19 Customs Duties 1 2011-04-01 2011-04-01 false Technical requirements for containers by design...

19 CFR 115.30 - Technical requirements for containers by design type.

Code of Federal Regulations, 2012 CFR

2012-04-01

... SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.30 Technical... 19 Customs Duties 1 2012-04-01 2012-04-01 false Technical requirements for containers by design...

19 CFR 115.30 - Technical requirements for containers by design type.

Code of Federal Regulations, 2014 CFR

2014-04-01

... SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.30 Technical... 19 Customs Duties 1 2014-04-01 2014-04-01 false Technical requirements for containers by design...

19 CFR 115.30 - Technical requirements for containers by design type.

Code of Federal Regulations, 2010 CFR

2010-04-01

... SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.30 Technical... 19 Customs Duties 1 2010-04-01 2010-04-01 false Technical requirements for containers by design...

19 CFR 115.30 - Technical requirements for containers by design type.

Code of Federal Regulations, 2013 CFR

2013-04-01

... SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.30 Technical... 19 Customs Duties 1 2013-04-01 2013-04-01 false Technical requirements for containers by design...

Constructing a modern cytology laboratory: A toolkit for planning and design

PubMed Central

Roberson, Janie; Wrenn, Allison; Poole, John; Jaeger, Andrew; Eltoum, Isam A.

2013-01-01

Introduction: Constructing or renovating a laboratory can be both challenging and rewarding. UAB Cytology (UAB CY) recently undertook a project to relocate from a building constructed in 1928 to new space. UAB CY is part of an academic center that provides service to a large set of patients, support training of one cytotechnology program and one cytopathology fellowship training program and involve actively in research and scholarly activity. Our objectives were to provide a safe, aesthetically pleasing space and gain efficiencies through lean processes. Methods: The phases of any laboratory design project are Planning, Schematic Design (SD), Design Development (DD), Construction Documents (CD) and Construction. Lab personnel are most critical in the Planning phase. During this time stakeholders, relationships, budget, square footage and equipment were identified. Equipment lists, including what would be relocated, purchased new and projected for future growth ensure that utilities were matched to expected need. A chemical inventory was prepared and adequate storage space was planned. Regulatory and safety requirements were discussed. Tours and high level process flow diagrams helped architects and engineers understand the laboratory daily work. Future needs were addressed through a questionnaire which identified potential areas of growth and technological change. Throughout the project, decisions were driven by data from the planning phase. During the SD phase, objective information from the first phase was used by architects and planners to create a general floor plan. This was the basis of a series of meetings to brainstorm and suggest modifications. DD brings more detail to the plans with engineering, casework, equipment specifics, finishes. Design changes should be completed at this phase. The next phase, CD took the project from the lab purview into purely technical mode. Construction documents were used by the contractor for the bidding process and

Management of technical date in Nihon Doro kodan

NASA Astrophysics Data System (ADS)

Hanada, Jun'ichi

Nihon Doro Kodan Laboratory has collected and contributed technical data (microfiches, aerial photographs, books and literature) on plans, designs, constructions and maintenance of the national expressways and the ordinary toll roads since 1968. This work is systematized on computer to retrieve and contribute data faster. Now Laboratory operates Technical Data Management System which manages all of technical data and Technical Document Management System which manages technical documents. These systems stand on users' on-line retrieval and data accumuration by microfiches and optical disks.

24 CFR 941.402 - Project design and construction.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 4 2011-04-01 2011-04-01 false Project design and construction... URBAN DEVELOPMENT PUBLIC HOUSING DEVELOPMENT Project Development § 941.402 Project design and.... A PHA may certify that its proposed design and construction plans for the development are in...

7 CFR 3575.42 - Design and construction requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 15 2011-01-01 2011-01-01 false Design and construction requirements. 3575.42 Section..., DEPARTMENT OF AGRICULTURE GENERAL Community Programs Guaranteed Loans § 3575.42 Design and construction... all funds were utilized for authorized purposes. The borrower and the lender will authorize designs...

7 CFR 3560.559 - Design and construction requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 15 2011-01-01 2011-01-01 false Design and construction requirements. 3560.559... § 3560.559 Design and construction requirements. (a) General. The requirements established in § 3560.60... encouraged that the design of off-farm labor housing incorporate outdoor shower, boot washing station, and/or...

A lunar construction shack vehicle: Final design

NASA Technical Reports Server (NTRS)

1988-01-01

A lunar construction shack vehicle is a critical component in most of the plans proposed for the construction of a permanent base on the moon. The Selene Engineering Company (SEC) has developed a concept for this vehicle which is both innovative and practical. The design makes use of the most advanced technology available to meet the goals for a safe, versatile and durable habitat that will serve as a starting point for the initial phase of the construction of a permanent lunar base. This document outlines SEC's proposed design for a lander vehicle which will be fully self-sufficient and will provide for all necessary life support, including consumables and radiation protection, needed by the construction crew until they can complete the assembly of a more permanent habitat. Since it is highly likely that it will take more than one crew to complete the construction of a permanent lunar base, the design emphasis is on systems which can be easily maintained and resupplied and which will take a minimum of start up preparation by succeeding crews.

Drafting & Design Technology. Technical Committee Report.

ERIC Educational Resources Information Center

Idaho State Dept. of Education, Boise. Div. of Vocational Education.

This Technical Committee Report prepared by industry representatives in Idaho lists the skills currently necessary for an employee in that state to obtain a job in drafting and design technology, retain a job once hired, and advance in that occupational field. (Task lists are grouped according to duty areas generally used in industry settings, and…

Technical challenges in the construction of the steady-state stellarator Wendelstein 7-X

NASA Astrophysics Data System (ADS)

Bosch, H.-S.; Wolf, R. C.; Andreeva, T.; Baldzuhn, J.; Birus, D.; Bluhm, T.; Bräuer, T.; Braune, H.; Bykov, V.; Cardella, A.; Durodié, F.; Endler, M.; Erckmann, V.; Gantenbein, G.; Hartmann, D.; Hathiramani, D.; Heimann, P.; Heinemann, B.; Hennig, C.; Hirsch, M.; Holtum, D.; Jagielski, J.; Jelonnek, J.; Kasparek, W.; Klinger, T.; König, R.; Kornejew, P.; Kroiss, H.; Krom, J. G.; Kühner, G.; Laqua, H.; Laqua, H. P.; Lechte, C.; Lewerentz, M.; Maier, J.; McNeely, P.; Messiaen, A.; Michel, G.; Ongena, J.; Peacock, A.; Pedersen, T. S.; Riedl, R.; Riemann, H.; Rong, P.; Rust, N.; Schacht, J.; Schauer, F.; Schroeder, R.; Schweer, B.; Spring, A.; Stäbler, A.; Thumm, M.; Turkin, Y.; Wegener, L.; Werner, A.; Zhang, D.; Zilker, M.; Akijama, T.; Alzbutas, R.; Ascasibar, E.; Balden, M.; Banduch, M.; Baylard, Ch.; Behr, W.; Beidler, C.; Benndorf, A.; Bergmann, T.; Biedermann, C.; Bieg, B.; Biel, W.; Borchardt, M.; Borowitz, G.; Borsuk, V.; Bozhenkov, S.; Brakel, R.; Brand, H.; Brown, T.; Brucker, B.; Burhenn, R.; Buscher, K.-P.; Caldwell-Nichols, C.; Cappa, A.; Cardella, A.; Carls, A.; Carvalho, P.; Ciupiński, Ł.; Cole, M.; Collienne, J.; Czarnecka, A.; Czymek, G.; Dammertz, G.; Dhard, C. P.; Davydenko, V. I.; Dinklage, A.; Drevlak, M.; Drotziger, S.; Dudek, A.; Dumortier, P.; Dundulis, G.; Eeten, P. v.; Egorov, K.; Estrada, T.; Faugel, H.; Fellinger, J.; Feng, Y.; Fernandes, H.; Fietz, W. H.; Figacz, W.; Fischer, F.; Fontdecaba, J.; Freund, A.; Funaba, T.; Fünfgelder, H.; Galkowski, A.; Gates, D.; Giannone, L.; García Regaña, J. M.; Geiger, J.; Geißler, S.; Greuner, H.; Grahl, M.; Groß, S.; Grosman, A.; Grote, H.; Grulke, O.; Haas, M.; Haiduk, L.; Hartfuß, H.-J.; Harris, J. H.; Haus, D.; Hein, B.; Heitzenroeder, P.; Helander, P.; Heller, R.; Hidalgo, C.; Hildebrandt, D.; Höhnle, H.; Holtz, A.; Holzhauer, E.; Holzthüm, R.; Huber, A.; Hunger, H.; Hurd, F.; Ihrke, M.; Illy, S.; Ivanov, A.; Jablonski, S.; Jaksic, N.; Jakubowski, M.; Jaspers, R.; Jensen, H.; Jenzsch, H.; Kacmarczyk, J.; Kaliatk, T.; Kallmeyer, J.; Kamionka, U.; Karaleviciu, R.; Kern, S.; Keunecke, M.; Kleiber, R.; Knauer, J.; Koch, R.; Kocsis, G.; Könies, A.; Köppen, M.; Koslowski, R.; Koshurinov, J.; Krämer-Flecken, A.; Krampitz, R.; Kravtsov, Y.; Krychowiak, M.; Krzesinski, G.; Ksiazek, I.; Kubkowska, M.; Kus, A.; Langish, S.; Laube, R.; Laux, M.; Lazerson, S.; Lennartz, M.; Li, C.; Lietzow, R.; Lohs, A.; Lorenz, A.; Louche, F.; Lubyako, L.; Lumsdaine, A.; Lyssoivan, A.; Maaßberg, H.; Marek, P.; Martens, C.; Marushchenko, N.; Mayer, M.; Mendelevitch, B.; Mertens, Ph.; Mikkelsen, D.; Mishchenko, A.; Missal, B.; Mizuuchi, T.; Modrow, H.; Mönnich, T.; Morizaki, T.; Murakami, S.; Musielok, F.; Nagel, M.; Naujoks, D.; Neilson, H.; Neubauer, O.; Neuner, U.; Nocentini, R.; Noterdaeme, J.-M.; Nührenberg, C.; Obermayer, S.; Offermanns, G.; Oosterbeek, H.; Otte, M.; Panin, A.; Pap, M.; Paquay, S.; Pasch, E.; Peng, X.; Petrov, S.; Pilopp, D.; Pirsch, H.; Plaum, B.; Pompon, F.; Povilaitis, M.; Preinhaelter, J.; Prinz, O.; Purps, F.; Rajna, T.; Récsei, S.; Reiman, A.; Reiter, D.; Remmel, J.; Renard, S.; Rhode, V.; Riemann, J.; Rimkevicius, S.; Riße, K.; Rodatos, A.; Rodin, I.; Romé, M.; Roscher, H.-J.; Rummel, K.; Rummel, Th.; Runov, A.; Ryc, L.; Sachtleben, J.; Samartsev, A.; Sanchez, M.; Sano, F.; Scarabosio, A.; Schmid, M.; Schmitz, H.; Schmitz, O.; Schneider, M.; Schneider, W.; Scheibl, L.; Scholz, M.; Schröder, G.; Schröder, M.; Schruff, J.; Schumacher, H.; Shikhovtsev, I. V.; Shoji, M.; Siegl, G.; Skodzik, J.; Smirnow, M.; Speth, E.; Spong, D. A.; Stadler, R.; Sulek, Z.; Szabó, V.; Szabolics, T.; Szetefi, T.; Szökefalvi-Nagy, Z.; Tereshchenko, A.; Thomsen, H.; Thumm, M.; Timmermann, D.; Tittes, H.; Toi, K.; Tournianski, M.; Toussaint, U. v.; Tretter, J.; Tulipán, S.; Turba, P.; Uhlemann, R.; Urban, J.; Urbonavicius, E.; Urlings, P.; Valet, S.; Van Eester, D.; Van Schoor, M.; Vervier, M.; Viebke, H.; Vilbrandt, R.; Vrancken, M.; Wauters, T.; Weissgerber, M.; Weiß, E.; Weller, A.; Wendorf, J.; Wenzel, U.; Windisch, T.; Winkler, E.; Winkler, M.; Wolowski, J.; Wolters, J.; Wrochna, G.; Xanthopoulos, P.; Yamada, H.; Yokoyama, M.; Zacharias, D.; Zajac, J.; Zangl, G.; Zarnstorff, M.; Zeplien, H.; Zoletnik, S.; Zuin, M.

2013-12-01

The next step in the Wendelstein stellarator line is the large superconducting device Wendelstein 7-X, currently under construction in Greifswald, Germany. Steady-state operation is an intrinsic feature of stellarators, and one key element of the Wendelstein 7-X mission is to demonstrate steady-state operation under plasma conditions relevant for a fusion power plant. Steady-state operation of a fusion device, on the one hand, requires the implementation of special technologies, giving rise to technical challenges during the design, fabrication and assembly of such a device. On the other hand, also the physics development of steady-state operation at high plasma performance poses a challenge and careful preparation. The electron cyclotron resonance heating system, diagnostics, experiment control and data acquisition are prepared for plasma operation lasting 30 min. This requires many new technological approaches for plasma heating and diagnostics as well as new concepts for experiment control and data acquisition.

Study of job burnout in technical writers and technical illustrators/designers at LLNL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rice, J A

According to the American Institute of Stress, job stress is estimated to cost American industry more than $200 billion a year. These costs are, in part, related to the estimated 1 million employees that will be absent on an average workday because of stress; 75 percent of visits to primary care physicians are for stress-related problems. California workers' compensation claims for stress cost $1 billion for medical and legal fees alone (Murphy, 1997). But, there is another dimension to stress that needs to be addressed. Job stress can be a precursor to job burnout. Burnout is a loss of motivation,more » and antidotes for job stress will not necessarily alleviate or stop job burnout. Job burnout is experienced as exhaustion on physical, emotional, and cognitive levels. Burnout can include withdrawal and decreasing involvement on the job, seriously affecting job satisfaction, turnover, absenteeism, and productivity (Dwyer & Ganster, 1991; Erickson & Gunderson, 1972; Spector & Jex, 1991). The research project described in this paper examined whether job burnout exists in the technical writer and technical illustrator/designer occupations in the Technical Information Department at Lawrence Livermore National Laboratory. This study also determined at what age and after how many years of service these employees were most likely to experience job burnout, whether it affects men or women most, and if writers in a technical organization experience job burnout more than illustrators/designers in that organization.« less

Architects' perspectives on construction waste reduction by design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Osmani, M.; Glass, J.; Price, A.D.F.

2008-07-01

The construction, demolition and excavation waste arising in England was estimated at 91 million tonnes in 2003. The current thinking on construction waste minimisation is heavily focussed on several issues relating to physical construction waste and recycling guides. Indeed, much had been published on ways to improve on-site waste management and recycling activities but very few attempts made to address the effect of design practices on waste generation. However, there is a consensus in the literature that the architect has a decisive role to play in helping to reduce waste by focussing on designing out waste. This paper examines previousmore » studies on architects' approach towards construction waste minimisation; and by means of a postal questionnaire, investigates: the origins of waste; waste minimisation design practices in the UK; and responsibilities and barriers within the UK architectural profession. The findings reveal that waste management is not a priority in the design process. Additionally, the architects seemed to take the view that waste is mainly produced during site operations and rarely generated during the design stages; however, about one-third of construction waste could essentially arise from design decisions. Results also indicate that a number of constraints, namely: lack of interest from clients; attitudes towards waste minimisation; and training all act as disincentives to a proactive and sustainable implementation of waste reduction strategies during the design process.« less

Architects' perspectives on construction waste reduction by design.

PubMed

Osmani, M; Glass, J; Price, A D F

2008-01-01

The construction, demolition and excavation waste arising in England was estimated at 91 million tonnes in 2003. The current thinking on construction waste minimisation is heavily focussed on several issues relating to physical construction waste and recycling guides. Indeed, much had been published on ways to improve on-site waste management and recycling activities but very few attempts made to address the effect of design practices on waste generation. However, there is a consensus in the literature that the architect has a decisive role to play in helping to reduce waste by focussing on designing out waste. This paper examines previous studies on architects' approach towards construction waste minimisation; and by means of a postal questionnaire, investigates: the origins of waste; waste minimisation design practices in the UK; and responsibilities and barriers within the UK architectural profession. The findings reveal that waste management is not a priority in the design process. Additionally, the architects seemed to take the view that waste is mainly produced during site operations and rarely generated during the design stages; however, about one-third of construction waste could essentially arise from design decisions. Results also indicate that a number of constraints, namely: lack of interest from clients; attitudes towards waste minimisation; and training all act as disincentives to a proactive and sustainable implementation of waste reduction strategies during the design process.

New Technical Solution for Vertical Shaft Equipping Using Steel Headframe of Multifunction Purpose

NASA Astrophysics Data System (ADS)

Kassikhina, Elena; Pershin, Vladimir; Glazkov, Yurij

2017-11-01

The article reviews a novel approach to the design of steel angle headframe for vertical shafts of coal and ore mines on the basis of rational design solutions. Practice of construction of coal and ore mines provides application of various designs for steel angle headframes which are divided into separate large assembly blocks and constructive elements during assembling operations. Design of these blocks and elements, their weight and dimensions effect the chose of the method of assembling on which economic and technological indicators, as well as duration of down-time, depend on during performance of construction operations in shaft. The technical solution on equipment provision for mine vertical shaft using headframe of multifunctional purpose will allow changing the management construction of vertical shaft. The constructive design of the headgear allows application of the effective method of assembly and thus to provide improvement of the technical and economic indexes, and high calendar time rate of the shaft construction due to reduction of duration of works on equipment provision for the shaft and to refurbishment of the shaft in order to carry out horizontal mining.

SINERGIA laparoscopic virtual reality simulator: didactic design and technical development.

PubMed

Lamata, Pablo; Gómez, Enrique J; Sánchez-Margallo, Francisco M; López, Oscar; Monserrat, Carlos; García, Verónica; Alberola, Carlos; Florido, Miguel Angel Rodríguez; Ruiz, Juan; Usón, Jesús

2007-03-01

VR laparoscopic simulators have demonstrated its validity in recent studies, and research should be directed towards a high training effectiveness and efficacy. In this direction, an insight into simulators' didactic design and technical development is provided, by describing the methodology followed in the building of the SINERGIA simulator. It departs from a clear analysis of training needs driven by a surgical training curriculum. Existing solutions and validation studies are an important reference for the definition of specifications, which are described with a suitable use of simulation technologies. Five new didactic exercises are proposed to train some of the basic laparoscopic skills. Simulator construction has required existing algorithms and the development of a particle-based biomechanical model, called PARSYS, and a collision handling solution based in a multi-point strategy. The resulting VR laparoscopic simulator includes new exercises and enhanced simulation technologies, and is finding a very good acceptance among surgeons.

49 CFR 230.66 - Design, construction, and maintenance.

Code of Federal Regulations, 2010 CFR

2010-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS Steam Locomotives and Tenders § 230.66 Design, construction, and maintenance. The steam locomotive owner and operator are responsible for the general design, construction and maintenance of the steam locomotives and...

Design of the Grimethorpe Experimental Facility as of March 1981: a technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1984-06-01

The Experimental Pressurized Fluidized Bed Combustor, which has been built as an extension to the National Coal Board Power Station, which is adjacent to Grimethorpe Colliery, Yorkshire, England, is described in this report. The Governments of the United Kingdom, the United States of America and the Federal Republic of Germany, under the auspices of the International Energy Agency, have agreed to share equally between them the costs of building and operating the plant. Control of the project was vested in an Executive Committee consisting of one representative of each Government with all decisions requiring unanimity. The actual operation of themore » project was vested in an Operating Agent, NCB (IEA Services) Ltd., a wholly owned subsidiary of the National Coal Board. The Implementing Agreement envisages a seven year project to be executed in four stages: (1) Procurement of Design Study with accompanying tender documents. (2) Tendering for construction of the Plant; study of appraisal of tenders. (3) Construction and acceptance of the Plant. (4) Operation of the Plant. The project is now towards the end of Stage 3. Construction has been completed and commissioning is in progress to prepare the plant for the start of the operational phase in Autumn 1981. Because of the confidentiality of much of the design information, for the purposes of this report technical descriptions have been confined to that of a general appraisal.« less

Computer-Aided Design Applications for the Base Civil Engineering Technical Design Section.

DTIC Science & Technology

1983-09-01

4 1983.’ S DEPARTMENT OF TiHE AIR FORCE L ~j AIR UNIVERSITY * AIR FORCE INSTITUTE OF TECHNOLOGY Nam Wright- Patterson Air Force Bas, Ohio d ’rI ’ 4to...I -. L I 1it it COMPUTER-AIDED DESIGN APPLICATIONS FOR THE BASE CIVIL ENGINEERING TECHNICAL DESIGN SECTION William M. Duncan, Captain, USAF LSSR 15-83...8217 .. ’ , .. - -. . ’ . , ._, - . . - .2 , _ : ’i 1 . . . . .- J.. .. . ’ _ -i l - , . analysis and design, water supply and wastewater disposal system design, and most

39 CFR 776.6 - Design requirements for construction.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 39 Postal Service 1 2010-07-01 2010-07-01 false Design requirements for construction. 776.6 Section 776.6 Postal Service UNITED STATES POSTAL SERVICE ENVIRONMENTAL REGULATIONS FLOODPLAIN AND WETLAND PROCEDURES Floodplain Management § 776.6 Design requirements for construction. If structures impact, are...

International Linear Collider Technical Design Report (Volumes 1 through 4)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harrison M.

2013-03-27

The design report consists of four volumes: Volume 1, Executive Summary; Volume 2, Physics; Volume 3, Accelerator (Part I, R and D in the Technical Design Phase, and Part II, Baseline Design); and Volume 4, Detectors.

10 CFR 52.137 - Contents of applications; technical information.

Code of Federal Regulations, 2012 CFR

2012-01-01

... FOR NUCLEAR POWER PLANTS Standard Design Approvals § 52.137 Contents of applications; technical... power plants similar in design and location to plants for which construction permits have previously... light-water-cooled nuclear power plants, an evaluation of the standard plant design against the Standard...

10 CFR 52.137 - Contents of applications; technical information.

Code of Federal Regulations, 2011 CFR

2011-01-01

... FOR NUCLEAR POWER PLANTS Standard Design Approvals § 52.137 Contents of applications; technical... power plants similar in design and location to plants for which construction permits have previously... light-water-cooled nuclear power plants, an evaluation of the standard plant design against the Standard...

10 CFR 52.137 - Contents of applications; technical information.

Code of Federal Regulations, 2014 CFR

2014-01-01

... FOR NUCLEAR POWER PLANTS Standard Design Approvals § 52.137 Contents of applications; technical... power plants similar in design and location to plants for which construction permits have previously... light-water-cooled nuclear power plants, an evaluation of the standard plant design against the Standard...

10 CFR 52.137 - Contents of applications; technical information.

Code of Federal Regulations, 2013 CFR

2013-01-01

... FOR NUCLEAR POWER PLANTS Standard Design Approvals § 52.137 Contents of applications; technical... power plants similar in design and location to plants for which construction permits have previously... light-water-cooled nuclear power plants, an evaluation of the standard plant design against the Standard...

23 CFR 1235.7 - Parking space design, construction, and designation.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 23 Highways 1 2011-04-01 2011-04-01 false Parking space design, construction, and designation. 1235.7 Section 1235.7 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION AND FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION GUIDELINES UNIFORM SYSTEM FOR PARKING FOR PERSONS WITH DISABILITIES § 1235.7 Parking space design,...

Design and Delivery of Technical Module for the Business Intelligence Course

ERIC Educational Resources Information Center

Wang, Shouhong; Wang, Hai

2013-01-01

IS programs are increasingly being called on to offer courses in business intelligence. This article presents the pedagogical design and the delivery method of a practicable technical module for a non-technically oriented Business Intelligence course. It is a tutorial for the instructors who wish to incorporate a practical technical element in…

33 CFR 127.101 - Design and construction: General.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Design and construction: General. 127.101 Section 127.101 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY... HAZARDOUS GAS Waterfront Facilities Handling Liquefied Natural Gas § 127.101 Design and construction...

Mass of materials: the impact of designers on construction ergonomics.

PubMed

Smallwood, John

2012-01-01

Many construction injuries are musculoskeletal related in the form of sprains and strains arising from the handling of materials, which are specified by designers. The paper presents the results of a study conducted among delegates attending two 'designing for H&S' (DfH&S) seminars using a questionnaire. The salient findings include: the level of knowledge relative to the mass and density of materials is limited; designers generally do not consider the mass and density of materials when designing structures and elements and specifying materials; to a degree designers appreciate that the mass and density of materials impact on construction ergonomics; designers rate their knowledge of the mass and density of materials as limited, and designers appreciate the potential of the consideration of the mass and density of materials to contribute to an improvement in construction ergonomics. Conclusions include: designers lack the requisite knowledge relative to the mass and density of materials; designers are thus precluded from conducting optimum design hazard identification and risk assessments, and tertiary built environment designer education does not enlighten designers relative to construction ergonomics. Recommendations include: tertiary built environment designer education should construction ergonomics; professional associations should raise the level of awareness relative to construction ergonomics, and design practices should include a category 'mass and density of materials' in their practice libraries.

Construction Mechanic Part I, 8-5. Military Curriculum Materials for Vocational and Technical Education.

ERIC Educational Resources Information Center

Ohio State Univ., Columbus. National Center for Research in Vocational Education.

This course, adapted from military curriculum materials for use in vocational and technical education, is the first of a two-course series that teaches students to maintain and repair automotive and construction equipment using either gasoline or diesel engines. It covers basic combustion engine principles and electrical system principles as well…

Construction Mechanic Part II, 8-6. Military Curriculum Materials for Vocational and Technical Education.

ERIC Educational Resources Information Center

Ohio State Univ., Columbus. National Center for Research in Vocational Education.

This course, adapted from military curriculum materials for use in vocational and technical education, is the second of a two-course series that teaches students to maintain and repair automotive and construction equipment using either gasoline or diesel engines. It covers basic chassis and power train troubleshooting, diagnosis, and adjustment…

78 FR 46546 - Design-Build Contracting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-01

...-0043] RIN 2125-AF58 Design-Build Contracting AGENCY: Federal Highway Administration (FHWA), DOT. ACTION... alternative technical concepts (ATC) in design-build project delivery of highway construction. The revisions... design-build proposers to submit ATCs in their technical and price proposals. The FHWA seeks comments on...

46 CFR 58.05-1 - Material, design and construction.

Code of Federal Regulations, 2014 CFR

2014-10-01

... AUXILIARY MACHINERY AND RELATED SYSTEMS Main Propulsion Machinery § 58.05-1 Material, design and construction. (a) The material, design, construction, workmanship, and arrangement of main propulsion machinery...

46 CFR 58.05-1 - Material, design and construction.

Code of Federal Regulations, 2012 CFR

2012-10-01

... AUXILIARY MACHINERY AND RELATED SYSTEMS Main Propulsion Machinery § 58.05-1 Material, design and construction. (a) The material, design, construction, workmanship, and arrangement of main propulsion machinery...

46 CFR 58.05-1 - Material, design and construction.

Code of Federal Regulations, 2011 CFR

2011-10-01

... AUXILIARY MACHINERY AND RELATED SYSTEMS Main Propulsion Machinery § 58.05-1 Material, design and construction. (a) The material, design, construction, workmanship, and arrangement of main propulsion machinery...

46 CFR 58.05-1 - Material, design and construction.

Code of Federal Regulations, 2010 CFR

2010-10-01

... AUXILIARY MACHINERY AND RELATED SYSTEMS Main Propulsion Machinery § 58.05-1 Material, design and construction. (a) The material, design, construction, workmanship, and arrangement of main propulsion machinery...

46 CFR 58.05-1 - Material, design and construction.

Code of Federal Regulations, 2013 CFR

2013-10-01

... AUXILIARY MACHINERY AND RELATED SYSTEMS Main Propulsion Machinery § 58.05-1 Material, design and construction. (a) The material, design, construction, workmanship, and arrangement of main propulsion machinery...

Design of Road Pavement Using Recycled Aggregate

NASA Astrophysics Data System (ADS)

Remišová, Eva; Decký, Martin; Mikolaš, Milan; Hájek, Matej; Kovalčík, Luboš; Mečár, Martin

2016-10-01

The presented article gives special attention to codified clauses of the road construction law, the relevant clauses of the standards and technical regulations to design and control the quality of recycled aggregate constructions. The article also presents the authors’ suggestions to design of earth constructions and pavements of roads according to the Slovak technical standards, technical regulations and objectively determined results of research and development of road infrastructure. The article presents a comparison of the mechanical characteristics measurements of the structural layers of road pavements built from the recycled and natural aggregate. It also presents correlation functions of results obtained from in situ and in laboratory CBR (Californian Bearing Ratio) measuring, representing the world's most widely used control method of bearing capacity of mentioned construction layers.

Information support of monitoring of technical condition of buildings in construction risk area

NASA Astrophysics Data System (ADS)

Skachkova, M. E.; Lepihina, O. Y.; Ignatova, V. V.

2018-05-01

The paper presents the results of the research devoted to the development of a model of information support of monitoring buildings technical condition; these buildings are located in the construction risk area. As a result of the visual and instrumental survey, as well as the analysis of existing approaches and techniques, attributive and cartographic databases have been created. These databases allow monitoring defects and damages of buildings located in a 30-meter risk area from the object under construction. The classification of structures and defects of these buildings under survey is presented. The functional capabilities of the developed model and the field of it practical applications are determined.

Facility design, construction, and operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

France has been disposing of low-level radioactive waste (LLW) at the Centre de Stockage de la Manche (CSM) since 1969 and now at the Centre de Stockage de l`Aube (CSA) since 1992. In France, several agencies and companies are involved in the development and implementation of LLW technology. The Commissariat a l`Energie Atomic (CEA), is responsible for research and development of new technologies. The Agence National pour la Gestion des Dechets Radioactifs is the agency responsible for the construction and operation of disposal facilities and for wastes acceptance for these facilities. Compagnie Generale des Matieres Nucleaires provides fuel services, includingmore » uranium enrichment, fuel fabrication, and fuel reprocessing, and is thus one generator of LLW. Societe pour les Techniques Nouvelles is an engineering company responsible for commercializing CEA waste management technology and for engineering and design support for the facilities. Numatec, Inc. is a US company representing these French companies and agencies in the US. In Task 1.1 of Numatec`s contract with Martin Marietta Energy Systems, Numatec provides details on the design, construction and operation of the LLW disposal facilities at CSM and CSA. Lessons learned from operation of CSM and incorporated into the design, construction and operating procedures at CSA are identified and discussed. The process used by the French for identification, selection, and evaluation of disposal technologies is provided. Specifically, the decisionmaking process resulting in the change in disposal facility design for the CSA versus the CSM is discussed. This report provides` all of the basic information in these areas and reflects actual experience to date.« less

23 CFR 652.13 - Design and construction criteria.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 23 Highways 1 2011-04-01 2011-04-01 false Design and construction criteria. 652.13 Section 652.13 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS PEDESTRIAN AND BICYCLE ACCOMMODATIONS AND PROJECTS § 652.13 Design and construction criteria. (a) The American Association of State Highway and...

39 CFR 776.6 - Design requirements for construction.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 39 Postal Service 1 2011-07-01 2011-07-01 false Design requirements for construction. 776.6 Section 776.6 Postal Service UNITED STATES POSTAL SERVICE ENVIRONMENTAL REGULATIONS FLOODPLAIN AND WETLAND PROCEDURES Floodplain Management § 776.6 Design requirements for construction. If structures impact, are located in, or support development in a...

21 CFR 129.20 - Plant construction and design.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 2 2013-04-01 2013-04-01 false Plant construction and design. 129.20 Section 129.20 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... § 129.20 Plant construction and design. (a) The bottling room shall be separated from other plant...

21 CFR 129.20 - Plant construction and design.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 2 2014-04-01 2014-04-01 false Plant construction and design. 129.20 Section 129.20 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... § 129.20 Plant construction and design. (a) The bottling room shall be separated from other plant...

21 CFR 129.20 - Plant construction and design.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 2 2012-04-01 2012-04-01 false Plant construction and design. 129.20 Section 129.20 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... § 129.20 Plant construction and design. (a) The bottling room shall be separated from other plant...

Problem Based Learning in Constructed Textile Design

ERIC Educational Resources Information Center

Sayer, Kate; Wilson, Jacquie; Challis, Simon

2006-01-01

Staff observing undergraduate students enrolled on the BSc Hons Textile Design and Design Management programme in The School of Materials, The University of Manchester, identified difficulties with knowledge retention in the area of constructed textile design. Consequently an experimental pilot was carried out in seamless knitwear design using a…

A unified approach to validation, reliability, and education study design for surgical technical skills training.

PubMed

Sweet, Robert M; Hananel, David; Lawrenz, Frances

2010-02-01

To present modern educational psychology theory and apply these concepts to validity and reliability of surgical skills training and assessment. In a series of cross-disciplinary meetings, we applied a unified approach of behavioral science principles and theory to medical technical skills education given the recent advances in the theories in the field of behavioral psychology and statistics. While validation of the individual simulation tools is important, it is only one piece of a multimodal curriculum that in and of itself deserves examination and study. We propose concurrent validation throughout the design of simulation-based curriculum rather than once it is complete. We embrace the concept that validity and curriculum development are interdependent, ongoing processes that are never truly complete. Individual predictive, construct, content, and face validity aspects should not be considered separately but as interdependent and complementary toward an end application. Such an approach could help guide our acceptance and appropriate application of these exciting new training and assessment tools for technical skills training in medicine.

Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eggeman, Tim; O'Neill, Brian

2016-08-17

ZeaChem Inc. and US DOE successfully demonstrated the ZeaChem process for producing sugars and ethanol from high-impact biomass feedstocks. The project was executed over a 5-year period under a $31.25 million cooperative agreement (80:20 Federal:ZeaChem cost share). The project was managed by dividing it into three budget periods. Activities during Budget Period 1 were limited to planning, permitting, and other pre-construction planning. Budget Period 2 activities included engineering, procurement, construction, commissioning, start-up and initial operations through the Independent Engineer Test Runs. The scope of construction was limited to the Chem Frac and Hydrogenolysis units, as the Core Facility was alreadymore » in place. Construction was complete in December 2012, and the first cellulosic ethanol was produced in February 2013. Additional operational test runs were conducted during Budget Period 3 (completed June 2015) using hybrid poplar, corn stover, and wheat straw feedstocks, resulting in the production of cellulosic ethanol and various other biorefinery intermediates. The research adds to the understanding of the Chem Frac and Hydrogenolysis technologies in that the technical performance of each unit was measured, and the resulting data and operational experience can be used as the basis for engineering designs, thus mitigating risks for deployment in future commercial facilities. The Chem Frac unit was initially designed to be operated as two-stage dilute acid hydrolysis, with first stage conditions selected to remove the hemicellulose fraction of the feedstock, and the second stage conditions selected to remove the cellulose fraction. While the Chem Frac unit met or exceeded the design capacity of 10 ton(dry)/day, the technical effectiveness of the Chem Frac unit was below expectations in its initial two-stage dilute acid configuration. The sugars yields were low, the sugars were dilute, and the sugars had poor fermentability caused by excessive

Technical Competencies Applied in Experimental Fluid Dynamics

NASA Astrophysics Data System (ADS)

Tagg, Randall

2017-11-01

The practical design, construction, and operation of fluid dynamics experiments require a broad range of competencies. Three types are instrumental, procedural, and design. Respective examples would be operation of a spectrum analyzer, soft-soldering or brazing flow plumbing, and design of a small wind tunnel. Some competencies, such as the selection and installation of pumping systems, are unique to fluid dynamics and fluids engineering. Others, such as the design and construction of electronic amplifiers or optical imaging systems, overlap with other fields. Thus the identification and development of learning materials and methods for instruction are part of a larger effort to identify competencies needed in active research and technical innovation.

Teaching Construction: A Design-Based Course Model

ERIC Educational Resources Information Center

Love, Tyler S.; Salgado, Carlos A.

2016-01-01

The focus on construction in T&E education has drastically changed. This article presents a series of topics and design-based labs that can be taught at various grade levels to integrate STEM concepts while also increasing students' overall awareness of construction and structural technologies.

Design, construction and operation features of high-rise structures

NASA Astrophysics Data System (ADS)

Mylnik, Alexey; Mylnik, Vladimir; Zubeeva, Elena; Mukhamedzhanova, Olga

2018-03-01

The article considers design, construction and operation features of high-rise facilities. The analysis of various situations, that come from improper designing, construction and operation of unique facilities, is carried out. The integrated approach is suggested, when the problems of choosing acceptable constructional solutions related to the functional purpose, architectural solutions, methods of manufacturing and installation, operating conditions for unique buildings and structures are being tackled. A number of main causes for the emergency destruction of objects under construction and operation is considered. A number of measures are proposed on the basis of factor classification in order to efficiently prevent the situations, when various negative options of design loads and emergency impacts occur.

47 CFR 18.109 - General technical requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 1 2011-10-01 2011-10-01 false General technical requirements. 18.109 Section 18.109 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL INDUSTRIAL, SCIENTIFIC, AND... designed and constructed in accordance with good engineering practice with sufficient shielding and...

47 CFR 18.109 - General technical requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 1 2012-10-01 2012-10-01 false General technical requirements. 18.109 Section 18.109 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL INDUSTRIAL, SCIENTIFIC, AND... designed and constructed in accordance with good engineering practice with sufficient shielding and...

47 CFR 18.109 - General technical requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false General technical requirements. 18.109 Section 18.109 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL INDUSTRIAL, SCIENTIFIC, AND... designed and constructed in accordance with good engineering practice with sufficient shielding and...

47 CFR 18.109 - General technical requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 1 2013-10-01 2013-10-01 false General technical requirements. 18.109 Section 18.109 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL INDUSTRIAL, SCIENTIFIC, AND... designed and constructed in accordance with good engineering practice with sufficient shielding and...

47 CFR 18.109 - General technical requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 1 2014-10-01 2014-10-01 false General technical requirements. 18.109 Section 18.109 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL INDUSTRIAL, SCIENTIFIC, AND... designed and constructed in accordance with good engineering practice with sufficient shielding and...

Infection control in design and construction work.

PubMed

Collinge, William H

2015-01-01

To clarify how infection control requirements are represented, communicated, and understood in work interactions through the medical facility construction project life cycle. To assist project participants with effective infection control management by highlighting the nature of such requirements and presenting recommendations to aid practice. A 4-year study regarding client requirement representation and use on National Health Service construction projects in the United Kingdom provided empirical evidence of infection control requirement communication and understanding through design and construction work interactions. An analysis of construction project resources (e.g., infection control regulations and room data sheets) was combined with semi-structured interviews with hospital client employees and design and construction professionals to provide valuable insights into the management of infection control issues. Infection control requirements are representationally indistinct but also omnipresent through all phases of the construction project life cycle: Failure to recognize their nature, relevance, and significance can result in delays, stoppages, and redesign work. Construction project resources (e.g., regulatory guidance and room data sheets) can mask or obscure the meaning of infection control issues. A preemptive identification of issues combined with knowledge sharing activities among project stakeholders can enable infection control requirements to be properly understood and addressed. Such initiatives should also reference existing infection control regulatory guidance and advice. © The Author(s) 2015.

Design of an autonomous Lunar construction utility vehicle

NASA Technical Reports Server (NTRS)

Ash, Robert L.; Chew, Mason; Dixon, Iain (Editor)

1990-01-01

In order to prepare a site for a manned lunar base, an autonomously operated construction vehicle is necessary. A Lunar Construction Utility Vehicle (LCUV), which utilizes interchangeable construction implements, was designed conceptually. Some elements of the machine were studied in greater detail. Design of an elastic loop track system has advanced to the testing stage. A standard coupling device was designed to insure a proper connection between the different construction tools and the LCUV. Autonomous control of the track drive motors was simulated successfully through the use of a joystick and computer interface. A study of hydrogen-oxygen fuel cells has produced estimates of reactant and product size requirements and identified multi-layer insulation techniques. Research on a 100 kW heat rejection system has determined that it is necessary to house a radiator panel on a utility trailer. The impact of a 720 hr use cycle has produced a very large logistical support lien which requires further study.

Technical Support Document: Development of the Advanced Energy Design Guide for Large Hospitals - 50% Energy Savings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bonnema, E.; Leach, M.; Pless, S.

2013-06-01

This Technical Support Document describes the process and methodology for the development of the Advanced Energy Design Guide for Large Hospitals: Achieving 50% Energy Savings Toward a Net Zero Energy Building (AEDG-LH) ASHRAE et al. (2011b). The AEDG-LH is intended to provide recommendations for achieving 50% whole-building energy savings in large hospitals over levels achieved by following Standard 90.1-2004. The AEDG-LH was created for a 'standard' mid- to large-size hospital, typically at least 100,000 ft2, but the strategies apply to all sizes and classifications of new construction hospital buildings. Its primary focus is new construction, but recommendations may be applicablemore » to facilities undergoing total renovation, and in part to many other hospital renovation, addition, remodeling, and modernization projects (including changes to one or more systems in existing buildings).« less

Performance/Design Requirements and Detailed Technical Description for a Computer-Directed Training Subsystem for Integration into the Air Force Phase II Base Level System.

ERIC Educational Resources Information Center

Butler, A. K.; And Others

The performance/design requirements and a detailed technical description for a Computer-Directed Training Subsystem to be integrated into the Air Force Phase II Base Level System are described. The subsystem may be used for computer-assisted lesson construction and has presentation capability for on-the-job training for data automation, staff, and…

Contextualizing Secure Information System Design: A Socio-Technical Approach

ERIC Educational Resources Information Center

Charif, Abdul Rahim

2017-01-01

Secure Information Systems (SIS) design paradigms have evolved in generations to adapt to IS security needs. However, modern IS are still vulnerable and are far from secure. The development of an underlying IS cannot be reduced to "technological fixes" neither is the design of SIS. Technical security cannot ensure IS security.…

Task Inventory Construction. Evaluation of the Marine Corps Task Analysis Program. Technical Report No. 14.

ERIC Educational Resources Information Center

Kishi, Akemi

To aid in the construction of effective task analysis inventories, this technical report discusses: (1) an optimum questionnaire length that adequately covers Marine tasks without unduly fatiguing respondents; (2) procedures for the phrasing of task statements to avoid ambiguities and be understandable to as broad a range of Marines as is…

Flexible Multi-Body Spacecraft Simulator: Design, Construction, and Experiments

DTIC Science & Technology

2017-12-01

BODY SPACECRAFT SIMULATOR: DESIGN , CONSTRUCTION, AND EXPERIMENTS by Adam L. Atwood December 2017 Thesis Advisor: Mark Karpenko Second...TYPE AND DATES COVERED Master’s thesis 4. TITLE AND SUBTITLE FLEXIBLE MULTI-BODY SPACECRAFT SIMULATOR: DESIGN , CONSTRUCTION, AND EXPERIMENTS 5...spacecraft simulator for use in testing optimal control-based slew and maneuver designs . The simulator is modified from an earlier prototype, which

Treatment of CHP in LEED® for Building Design and Construction: New Construction and Major Renovations

EPA Pesticide Factsheets

This factsheet introduces CHP and its benefits to architects and engineers, and summarizes how CHP is treated under the LEED® for Building Design and Construction: New Construction and Major Renovations (LEED BD+C: New Construction) rating system.

36 CFR 223.38 - Standards for road design and construction.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Provisions § 223.38 Standards for road design and construction. Road construction authorized under timber... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Standards for road design and construction. 223.38 Section 223.38 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF...

46 CFR 161.010-2 - Design, construction, and test requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Design, construction, and test requirements. 161.010-2 Section 161.010-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL ELECTRICAL EQUIPMENT Floating Electric Waterlight § 161.010-2 Design, construction, and test...

46 CFR 161.010-2 - Design, construction, and test requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Design, construction, and test requirements. 161.010-2 Section 161.010-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL ELECTRICAL EQUIPMENT Floating Electric Waterlight § 161.010-2 Design, construction, and test...

46 CFR 161.010-2 - Design, construction, and test requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Design, construction, and test requirements. 161.010-2 Section 161.010-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL ELECTRICAL EQUIPMENT Floating Electric Waterlight § 161.010-2 Design, construction, and test...

46 CFR 161.010-2 - Design, construction, and test requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 6 2011-10-01 2011-10-01 false Design, construction, and test requirements. 161.010-2 Section 161.010-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL ELECTRICAL EQUIPMENT Floating Electric Waterlight § 161.010-2 Design, construction, and test...

French vertical-flow constructed wetland design: adaptations for tropical climates.

PubMed

Molle, P; Latune, R Lombard; Riegel, C; Lacombe, G; Esser, D; Mangeot, L

2015-01-01

The French Outermost Regions are under tropical climate yet still have to comply with both French and EU regulations. French vertical-flow constructed wetland systems appear well adapted to the technical specifics of these regions but their adaptation to tropical climate requires new design guidelines to be defined (area needed, number of filters, type of plants, material to be used, etc.). A study was started in 2008, with backing from the national water authorities, to implement full-scale experimental sites and assess the impacts of local context on design and performances. This paper reports the monitoring results on three vertical-flow constructed wetlands fed directly with raw wastewater (known as the 'French system') in Mayotte and French Guiana. The plants, now in operation for between 1 and 6 years, range from 160 to 480 population equivalent (p.e.). Monitoring consisted of 28 daily composite flow samples in different seasons (dry season, rainy season) at the inlet and outlet of each filter. Performances are benchmarked against French mainland area standards from Irstea's database. Results show that performances are improved by warmer temperature for chemical oxygen demand (COD), suspended solids (SS) and total Kjeldahl nitrogen (TKN) and satisfy national quality objectives with a single stage of filters. Treatment plant footprint can thus be reduced as only two parallel filters are needed. Indeed, warm temperatures allow faster mineralization of the sludge deposit, making it possible to operate at similar rest and feeding period durations. Systems operated using one twin-filter stage can achieve over 90% COD, SS and TKN removal for a total surface of 0.8 m²/p.e.

Designing with Protocells: Applications of a Novel Technical Platform

PubMed Central

Armstrong, Rachel

2014-01-01

The paper offers a design perspective on protocell applications and presents original research that characterizes the life-like qualities of the Bütschli dynamic droplet system, as a particular “species” of protocell. Specific focus is given to the possibility of protocell species becoming a technical platform for designing and engineering life-like solutions to address design challenges. An alternative framing of the protocell, based on process philosophy, sheds light on its capabilities as a technology that can deal with probability and whose ontology is consistent with complexity, nonlinear dynamics and the flow of energy and matter. However, the proposed technical systems do not yet formally exist as products or mature technologies. Their potential applications are therefore experimentally examined within a design context as architectural “projects”—an established way of considering proposals that have not yet been realized, like an extended hypothesis. Exemplary design-led projects are introduced, such as The Hylozoic Ground and Future Venice, which aim to “discover”, rather than “solve”, challenges to examine a set of possibilities that have not yet been resolved. The value of such exploration in design practice is in opening up a set of potential directions for further assessment before complex challenges are procedurally implemented. PMID:25370381

6 CFR 27.120 - Designation of a coordinating official; Consultations and technical assistance.

Code of Federal Regulations, 2010 CFR

2010-01-01

... covered facility shall submit a written request for consultation or technical assistance to the...; Consultations and technical assistance. 27.120 Section 27.120 Domestic Security DEPARTMENT OF HOMELAND SECURITY... coordinating official; Consultations and technical assistance. (a) The Assistant Secretary will designate a...

48 CFR 1052.201-70 - Contracting Officer's Technical Representative (COTR) Designation and Authority.

Code of Federal Regulations, 2010 CFR

2010-10-01

... in writing. The term “technical direction” includes, without limitation, direction to the contractor... the actions of the contractor's employees. (d) Technical direction may be oral or in writing. The COTR... Technical Representative (COTR) Designation and Authority. 1052.201-70 Section 1052.201-70 Federal...

The constructal law and the evolution of design in nature.

PubMed

Bejan, Adrian; Lorente, Sylvie

2011-10-01

The constructal law accounts for the universal phenomenon of generation and evolution of design (configuration, shape, structure, pattern, rhythm). This phenomenon is observed across the board, in animate, inanimate and human systems. The constructal law states the time direction of the evolutionary design phenomenon. It defines the concept of design evolution in physics. Along with the first and second law, the constructal law elevates thermodynamics to a science of systems with configuration. In this article we review the more recent work of our group, with emphasis on the advances made with the constructal law in the natural sciences. Highlighted are the oneness of animate and inanimate designs, the origin of finite-size organs on animals and vehicles, the flow of stresses as the generator of design in solid structures (skeletons, vegetation), the universality and rigidity of hierarchy in all flow systems, and the global design of human flows. Noteworthy is the tapestry of distributed energy systems, which balances nodes of production with networks of distribution on the landscape, and serves as key to energy sustainability and empowerment. At the global level, the constructal law accounts for the geography and design of human movement, wealth and communications. Copyright © 2011 Elsevier B.V. All rights reserved.

Principles of Good School Building Design. School Buildings Planning, Design, and Construction Series No. 3.

ERIC Educational Resources Information Center

Odell, John H.

A school construction guide offers key personnel in school development projects information on the complex task of master planning and construction of schools in Australia. This chapter of the guide provides advice on school building design issues, such as the fundamentals of good design and designs that accommodate change, issues affecting…

Construction and Administration of Ten Air Force Job Inventories.

ERIC Educational Resources Information Center

Mayo, Clyde C.

Ten job inventories were constructed for survey of 11 Air Force career ladders. Background variables designed to assess task-related information were included in each inventory. A replication of a previous study of contributions of technical advisers to inventory construction supported the earlier finding that airmen at supervisory skill levels…

Design of an autonomous lunar construction utility vehicle

NASA Technical Reports Server (NTRS)

1990-01-01

In order to prepare a site for a lunar base, an autonomously operated construction vehicle is necessary. Discussed here is a Lunar Construction Utility Vehicle (LCUV), which uses interchangeable construction implements. Design of an elastic loop track system has advanced to the testing stage. A standard coupling device has been designed to insure a proper connection between the different construction tools and the LCUV. Autonomous control of the track drive motors was simulated successfully through the use of a joystick and a computer interface. A study of hydrogen-oxygen fuel cells produced estimates of reactant and product requirements and identified multilayer insulation needs. Research on the 100-kW heat rejection system determined that it is necessary to transport the radiator panel on a utility trailer. Extensive logistical support for the 720 hour use cycle requires further study.

FHWA road tunnel design guidelines

DOT National Transportation Integrated Search

2004-07-01

This document provides technical criteria and guidance for the planning and design of road tunnels. Specific areas covered include planning, studies and investigations, design, and design of construction, of tunnels and shafts. Performance concepts a...

Theorycrafting the Classroom: Constructing the Introductory Technical Communication Course as a Game

ERIC Educational Resources Information Center

Finseth, Carly

2015-01-01

When games are approached as a pedagogical methodology, the homologies between games and technical communication are highlighted: pedagogy that teaches people to play and succeed within certain confines; classroom assessment that provides meaningful feedback to encourage self-improvement; instructional design that incorporates gaming theory and…

Lateral support systems and underpinning, volume I : design and construction.

DOT National Transportation Integrated Search

1976-04-01

"This volume is a convenient reference on the design and construction of lateral support systems and underpinning which are often required in conjunction with cut-and-cover or soft ground tunneling. The design recommendations and construction methods...

Building Ecology & School Design. Technical Bulletin.

ERIC Educational Resources Information Center

Maryland State Dept. of Education, Baltimore.

To better understand construction's impact, an overview of building ecology as a concept and as a decision-making model for school systems is provided. "Building ecology" is defined as the interrelationships among people, the built environment, and the natural environment. It has special relevance for school design because most of the…

Lateral Support Systems And Underpinning. Volume I: Design And Construction

DOT National Transportation Integrated Search

1976-04-01

This volume is a convenient reference on the design and construction of lateral support systems and underpining which are often required in conjunction with cut-and-cover or soft ground tunneling. The design recommendations and construction methods d...

The constructal law of design and evolution in nature.

PubMed

Bejan, Adrian; Lorente, Sylvie

2010-05-12

Constructal theory is the view that (i) the generation of images of design (pattern, rhythm) in nature is a phenomenon of physics and (ii) this phenomenon is covered by a principle (the constructal law): 'for a finite-size flow system to persist in time (to live) it must evolve such that it provides greater and greater access to the currents that flow through it'. This law is about the necessity of design to occur, and about the time direction of the phenomenon: the tape of the design evolution 'movie' runs such that existing configurations are replaced by globally easier flowing configurations. The constructal law has two useful sides: the prediction of natural phenomena and the strategic engineering of novel architectures, based on the constructal law, i.e. not by mimicking nature. We show that the emergence of scaling laws in inanimate (geophysical) flow systems is the same phenomenon as the emergence of allometric laws in animate (biological) flow systems. Examples are lung design, animal locomotion, vegetation, river basins, turbulent flow structure, self-lubrication and natural multi-scale porous media. This article outlines the place of the constructal law as a self-standing law in physics, which covers all the ad hoc (and contradictory) statements of optimality such as minimum entropy generation, maximum entropy generation, minimum flow resistance, maximum flow resistance, minimum time, minimum weight, uniform maximum stresses and characteristic organ sizes. Nature is configured to flow and move as a conglomerate of 'engine and brake' designs.

40 CFR 125.99 - What are approved design and construction technologies?

Code of Federal Regulations, 2010 CFR

2010-07-01

... construction technologies? 125.99 Section 125.99 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...) of the Act § 125.99 What are approved design and construction technologies? (a) The following technologies constitute approved design and construction technologies for purposes of § 125.94(a)(4): (1...

40 CFR 125.99 - What are approved design and construction technologies?

Code of Federal Regulations, 2011 CFR

2011-07-01

... construction technologies? 125.99 Section 125.99 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...) of the Act § 125.99 What are approved design and construction technologies? (a) The following technologies constitute approved design and construction technologies for purposes of § 125.94(a)(4): (1...

40 CFR 125.99 - What are approved design and construction technologies?

Code of Federal Regulations, 2013 CFR

2013-07-01

... construction technologies? 125.99 Section 125.99 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...) of the Act § 125.99 What are approved design and construction technologies? (a) The following technologies constitute approved design and construction technologies for purposes of § 125.94(a)(4): (1...

40 CFR 125.99 - What are approved design and construction technologies?

Code of Federal Regulations, 2014 CFR

2014-07-01

... construction technologies? 125.99 Section 125.99 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...) of the Act § 125.99 What are approved design and construction technologies? (a) The following technologies constitute approved design and construction technologies for purposes of § 125.94(a)(4): (1...

40 CFR 125.99 - What are approved design and construction technologies?

Code of Federal Regulations, 2012 CFR

2012-07-01

... construction technologies? 125.99 Section 125.99 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...) of the Act § 125.99 What are approved design and construction technologies? (a) The following technologies constitute approved design and construction technologies for purposes of § 125.94(a)(4): (1...

Design and construction of an impulse turbine

NASA Astrophysics Data System (ADS)

Hernández, E.

2013-11-01

Impulse turbine has been constructed to be used in the program of Hydraulic Machines, Faculty of Mechanical Engineering at the Universidad Pontificia Bolivariana, sede Bucaramanga. For construction of the impulse turbine (Pelton) detailed plans were drawn up taking into account the design and implementation of the fundamental equations of hydraulic turbomachinery. From the experimental data found maximum mechanical efficiency of 0.6 ± 0.03 for a water flow of 2.1 l/s. The maximum overall efficiency was 0.23 ± 0.02 for a water flow of 0.83 l/s. The design parameter used was a power of 1 kW, as flow regulator built a needle type regulator, which performed well, the model of the bucket or vane is built on a machine type CNC (Computer Numerical Control). For the construction of the impeller and blades was used aluminium because of chemical and physical characteristics and the casing was manufactured in acrylic.

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

Boat Building Design and Construction Techniques in the Architectural Design Studio.

ERIC Educational Resources Information Center

Smith, Richard A.

1982-01-01

Describes a model boat building project for architectural design studios. Working from traditional sailboat designs, students study the "lines" drawings of boats, make full-size drawings from scale drawings, and then construct model wooden boats. Available from Carfax Publishing Company, P.O. Box 25, Abindgon, Oxfordshire OX14 1RW…

Information Design: A New Approach to Teaching Technical Writing Service Courses

ERIC Educational Resources Information Center

McKee, Candie DeLane

2012-01-01

This study used a needs assessment, process analysis, process design, and textbook design to develop a new process and new textbook, based on Cargile-Cook's layered literacies, Quesenbery's five qualities of usability, and Carliner's information design theories, for use in technical writing service learning courses. The needs assessment was based…

Security during the Construction of New Nuclear Power Plants: Technical Basis for Access Authorization and Fitness-For-Duty Requirements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Branch, Kristi M.; Baker, Kathryn A.

A technical letter report to the NRC summarizing the findings of a benchmarking study, literature review, and workshop with experts on current industry standards and expert judgments about needs for security during the construction phase of critical infrastructure facilities in the post-September 11 U.S. context, with a special focus on the construction phase of nuclear power plants and personnel security measures.

Value Engineering. Technical Manual. School Facilities Development Procedures Manual.

ERIC Educational Resources Information Center

Washington Office of the State Superintendent of Public Instruction, Olympia.

Value Engineering (VE) is a cost-optimizing technique used to analyze design quality and cost-effectiveness. The application of VE procedures to the design and construction of school facilities has been adopted by the state of Washington. This technical manual provides guidance in developing the scope and applicability of VE to school projects; in…

Purpose Designed Facilities. School Buildings Planning, Design, and Construction Series No. 4.

ERIC Educational Resources Information Center

Odell, John H.

A school construction guide offers key personnel in school development projects information on the complex task of master planning and construction of schools in Australia. This chapter of the guide provides advice on issues involving school space design and the kinds of spaces required in schools, including lecture spaces and seminar rooms,…

The constructal law of design and evolution in nature

PubMed Central

Bejan, Adrian; Lorente, Sylvie

2010-01-01

Constructal theory is the view that (i) the generation of images of design (pattern, rhythm) in nature is a phenomenon of physics and (ii) this phenomenon is covered by a principle (the constructal law): ‘for a finite-size flow system to persist in time (to live) it must evolve such that it provides greater and greater access to the currents that flow through it’. This law is about the necessity of design to occur, and about the time direction of the phenomenon: the tape of the design evolution ‘movie’ runs such that existing configurations are replaced by globally easier flowing configurations. The constructal law has two useful sides: the prediction of natural phenomena and the strategic engineering of novel architectures, based on the constructal law, i.e. not by mimicking nature. We show that the emergence of scaling laws in inanimate (geophysical) flow systems is the same phenomenon as the emergence of allometric laws in animate (biological) flow systems. Examples are lung design, animal locomotion, vegetation, river basins, turbulent flow structure, self-lubrication and natural multi-scale porous media. This article outlines the place of the constructal law as a self-standing law in physics, which covers all the ad hoc (and contradictory) statements of optimality such as minimum entropy generation, maximum entropy generation, minimum flow resistance, maximum flow resistance, minimum time, minimum weight, uniform maximum stresses and characteristic organ sizes. Nature is configured to flow and move as a conglomerate of ‘engine and brake’ designs. PMID:20368252

Full immersion simulation: validation of a distributed simulation environment for technical and non-technical skills training in Urology.

PubMed

Brewin, James; Tang, Jessica; Dasgupta, Prokar; Khan, Muhammad S; Ahmed, Kamran; Bello, Fernando; Kneebone, Roger; Jaye, Peter

2015-07-01

To evaluate the face, content and construct validity of the distributed simulation (DS) environment for technical and non-technical skills training in endourology. To evaluate the educational impact of DS for urology training. DS offers a portable, low-cost simulated operating room environment that can be set up in any open space. A prospective mixed methods design using established validation methodology was conducted in this simulated environment with 10 experienced and 10 trainee urologists. All participants performed a simulated prostate resection in the DS environment. Outcome measures included surveys to evaluate the DS, as well as comparative analyses of experienced and trainee urologist's performance using real-time and 'blinded' video analysis and validated performance metrics. Non-parametric statistical methods were used to compare differences between groups. The DS environment demonstrated face, content and construct validity for both non-technical and technical skills. Kirkpatrick level 1 evidence for the educational impact of the DS environment was shown. Further studies are needed to evaluate the effect of simulated operating room training on real operating room performance. This study has shown the validity of the DS environment for non-technical, as well as technical skills training. DS-based simulation appears to be a valuable addition to traditional classroom-based simulation training. © 2014 The Authors BJU International © 2014 BJU International Published by John Wiley & Sons Ltd.

Economic Evaluation of Building Design, Construction, Operation and Maintenance. Instructor's Manual.

ERIC Educational Resources Information Center

Ruegg, Rosalie T.; Marshall, Harold E.

This instructor's manual describes each section of a 3-day technical seminar on how to measure the economic impact of alternative designs, systems, and operation and maintenance strategies in federal buildings. The manual was prepared to help instructors of the General Services Administration conduct technically sound and comprehensive seminars.…

46 CFR 160.132-7 - Design, construction, and performance of davits.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Design, construction, and performance of davits. 160.132-7 Section 160.132-7 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Launching Appliances-Davits § 160.132-7 Design, construction, and...

46 CFR 160.132-7 - Design, construction, and performance of davits.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Design, construction, and performance of davits. 160.132-7 Section 160.132-7 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Launching Appliances-Davits § 160.132-7 Design, construction, and...

Independent technical review, handbook

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Purpose Provide an independent engineering review of the major projects being funded by the Department of Energy, Office of Environmental Restoration and Waste Management. The independent engineering review will address questions of whether the engineering practice is sufficiently developed to a point where a major project can be executed without significant technical problems. The independent review will focus on questions related to: (1) Adequacy of development of the technical base of understanding; (2) Status of development and availability of technology among the various alternatives; (3) Status and availability of the industrial infrastructure to support project design, equipment fabrication, facility construction,more » and process and program/project operation; (4) Adequacy of the design effort to provide a sound foundation to support execution of project; (5) Ability of the organization to fully integrate the system, and direct, manage, and control the execution of a complex major project.« less

The Advanced Technology Solar Telescope: design and early construction

NASA Astrophysics Data System (ADS)

McMullin, Joseph P.; Rimmele, Thomas R.; Keil, Stephen L.; Warner, Mark; Barden, Samuel; Bulau, Scott; Craig, Simon; Goodrich, Bret; Hansen, Eric; Hegwer, Steve; Hubbard, Robert; McBride, William; Shimko, Steve; Wöger, Friedrich; Ditsler, Jennifer

2012-09-01

The National Solar Observatory’s (NSO) Advanced Technology Solar Telescope (ATST) is the first large U.S. solar telescope accessible to the worldwide solar physics community to be constructed in more than 30 years. The 4-meter diameter facility will operate over a broad wavelength range (0.35 to 28 μm ), employing adaptive optics systems to achieve diffraction limited imaging and resolve features approximately 20 km on the Sun; the key observational parameters (collecting area, spatial resolution, spectral coverage, polarization accuracy, low scattered light) enable resolution of the theoretically-predicted, fine-scale magnetic features and their dynamics which modulate the radiative output of the sun and drive the release of magnetic energy from the Sun’s atmosphere in the form of flares and coronal mass ejections. In 2010, the ATST received a significant fraction of its funding for construction. In the subsequent two years, the project has hired staff and opened an office on Maui. A number of large industrial contracts have been placed throughout the world to complete the detailed designs and begin constructing the major telescope subsystems. These contracts have included the site development, AandE designs, mirrors, polishing, optic support assemblies, telescope mount and coudé rotator structures, enclosure, thermal and mechanical systems, and high-level software and controls. In addition, design development work on the instrument suite has undergone significant progress; this has included the completion of preliminary design reviews (PDR) for all five facility instruments. Permitting required for physically starting construction on the mountaintop of Haleakalā, Maui has also progressed. This paper will review the ATST goals and specifications, describe each of the major subsystems under construction, and review the contracts and lessons learned during the contracting and early construction phases. Schedules for site construction, key factory testing of

78 FR 33863 - Relationship Between General Design Criteria and Technical Specification Operability

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-05

... NUCLEAR REGULATORY COMMISSION [NRC-2012-0179] Relationship Between General Design Criteria and...) 2013-05, ``NRC Position on the Relationship Between General Design Criteria and Technical Specification Operability.'' This RIS clarifies the NRC staff's position on the relationship between the general design...

Rethinking Technical Communication Pedagogy: A Poststructuralist View of Program and Course Design.

ERIC Educational Resources Information Center

Woolever, Kristin R.

Technical communication specialists today really have to be technology experts as well as effective writers--even their titles have changed to "information designers, information engineers, or document developers." Teachers of technical communication should be up to date in the classroom to meet the changing needs of the workplace.…

Design and Construction Documents Associated with N232, Sustainability Base

NASA Technical Reports Server (NTRS)

Zornetzer, Steven F.; Schuler, Raymond F.; Grymes, Rosalind A.

2014-01-01

This request comprehensively covers documents associated with the design and construction of Sustainability Base, N232. The intent of this project specifically envisioned broad dissemination of these materials to others undertaking the design and construction of high-performing energy- and resource-efficient buildings in comparable climate zones.

IT Requirements Integration in High-Rise Construction Design Projects

NASA Astrophysics Data System (ADS)

Levina, Anastasia; Ilin, Igor; Esedulaev, Rustam

2018-03-01

The paper discusses the growing role of IT support for the operation of modern high-rise buildings, due to the complexity of managing engineering systems of buildings and the requirements of consumers for the IT infrastructure. The existing regulatory framework for the development of design documentation for construction, including high-rise buildings, is analyzed, and the lack of coherence in the development of this documentation with the requirements for the creation of an automated management system and the corresponding IT infrastructure is stated. The lack of integration between these areas is the cause of delays and inefficiencies both at the design stage and at the stage of putting the building into operation. The paper proposes an approach to coordinate the requirements of the IT infrastructure of high-rise buildings and design documentation for construction. The solution to this problem is possible within the framework of the enterprise architecture concept by coordinating the requirements of the IT and technological layers at the design stage of the construction.

46 CFR 160.066-5 - Design, construction, and manufacturing requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Design, construction, and manufacturing requirements... Boats, Red Aerial Pyrotechnic Flare § 160.066-5 Design, construction, and manufacturing requirements. (a... details occurs; (2) Any change in sources of raw materials occurs; (3) Production is started on a new...

36 CFR 223.38 - Standards for road design and construction.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 36 Parks, Forests, and Public Property 2 2011-07-01 2011-07-01 false Standards for road design and... PRODUCTS Timber Sale Contracts Contract Conditions and Provisions § 223.38 Standards for road design and construction. Road construction authorized under timber sale contracts, permits and other documents authorizing...

Designing Anticancer Peptides by Constructive Machine Learning.

PubMed

Grisoni, Francesca; Neuhaus, Claudia S; Gabernet, Gisela; Müller, Alex T; Hiss, Jan A; Schneider, Gisbert

2018-04-21

Constructive (generative) machine learning enables the automated generation of novel chemical structures without the need for explicit molecular design rules. This study presents the experimental application of such a deep machine learning model to design membranolytic anticancer peptides (ACPs) de novo. A recurrent neural network with long short-term memory cells was trained on α-helical cationic amphipathic peptide sequences and then fine-tuned with 26 known ACPs by transfer learning. This optimized model was used to generate unique and novel amino acid sequences. Twelve of the peptides were synthesized and tested for their activity on MCF7 human breast adenocarcinoma cells and selectivity against human erythrocytes. Ten of these peptides were active against cancer cells. Six of the active peptides killed MCF7 cancer cells without affecting human erythrocytes with at least threefold selectivity. These results advocate constructive machine learning for the automated design of peptides with desired biological activities. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Project DIVIDE Instrument Development. Technical Report # 0810

ERIC Educational Resources Information Center

Ketterlin-Geller, Leanne; Jung, Eunju; Geller, Josh; Yovanoff, Paul

2008-01-01

In this technical report, we describe the development of cognitive diagnostic test items that form the basis of the diagnostic system for Project DIVIDE (Dynamic Instruction Via Individually Designed Environments). The construct underlying the diagnostic test is division of fractions. We include a description of the process we used to identify the…

46 CFR 111.05-3 - Design, construction, and installation; general.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Design, construction, and installation; general. 111.05-3 Section 111.05-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Equipment Ground, Ground Detection, and Grounded Systems § 111.05-3 Design, construction, and...

46 CFR 111.05-3 - Design, construction, and installation; general.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Design, construction, and installation; general. 111.05-3 Section 111.05-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Equipment Ground, Ground Detection, and Grounded Systems § 111.05-3 Design, construction, and...

Qualitative Variation in Constructive Alignment in Curriculum Design

ERIC Educational Resources Information Center

Trigwell, Keith; Prosser, Michael

2014-01-01

Constructive alignment has emerged as a powerful curriculum design idea, but little is known of the extent to which the effectiveness of this idea is a function of qualitative variation. This article introduces a model of qualitative variation in constructive alignment, and uses the results from known alignment studies to test the model. The…

Conducting Research in Technical Communication: The Application of True Experimental Designs.

ERIC Educational Resources Information Center

Spyridakis, Jan H.

1992-01-01

Explains the use of true experimental designs in technical communication research, lists the eight steps in the research process, and concludes with the hope that practitioners should now be able to read research studies critically and perhaps design empirical studies of their own after further reading. (SR)

Technical Communication Competence and Projected Teacher Success.

ERIC Educational Resources Information Center

Powers, William G.; Lowry, David N.

Technical Communication Competence (TCC)is the competence involved in communicating mental images to others in such a manner as to result in their constructing comparable mental images, a process similar to the primary task demanded of teachers at all levels. In a study designed to discover the extent to which a positive relationship existed…

Brownfields Green Avenue Sites: Technical Memorandum - Conceptual Design for Sustainable Redevelopment

EPA Pesticide Factsheets

This technical memorandum briefly describes the site and proposed conceptual site plan, indicates conceptual design considerations, specifies recommended green and sustainable features, and offers other recommendations

Low-level liquid radioactive waste treatment at Murmansk, Russia: Technical design and review of facility upgrade and expansion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dyer, R.S.; Diamante, J.M.; Duffey, R.B.

1996-07-01

The governments of Norway and the US have committed their mutual cooperation and support the Murmansk Shipping Company (MSCo) to expand and upgrade the Low-Level Liquid Radioactive Waste (LLRW) treatment system located at the facilities of the Russian company RTP Atomflot, in Murmansk, Russia. RTP Atomflot provides support services to the Russian icebreaker fleet operated by the MSCo. The objective is to enable Russia to permanently cease disposing of this waste in Arctic waters. The proposed modifications will increase the facility`s capacity from 1,200 m{sup 3} per year to 5,000 m{sup 3} per year, will permit the facility to processmore » high-salt wastes from the Russian Navy`s Northern fleet, and will improve the stabilization and interim storage of the processed wastes. The three countries set up a cooperative review of the evolving design information, conducted by a joint US and Norwegian technical team from April through December, 1995. To ensure that US and Norwegian funds produce a final facility which will meet the objectives, this report documents the design as described by Atomflot and the Russian business organization, ASPECT, both in design documents and orally. During the detailed review process, many questions were generated, and many design details developed which are outlined here. The design is based on the adsorption of radionuclides on selected inorganic resins, and desalination and concentration using electromembranes. The US/Norwegian technical team reviewed the available information and recommended that the construction commence; they also recommended that a monitoring program for facility performance be instituted.« less

24 CFR 100.205 - Design and construction requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... FAIR HOUSING DISCRIMINATORY CONDUCT UNDER THE FAIR HOUSING ACT Prohibition Against Discrimination Because of Handicap § 100.205 Design and construction requirements. (a) Covered multifamily dwellings for... accessible to and usable by handicapped persons; (2) All the doors designed to allow passage into and within...

24 CFR 100.205 - Design and construction requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... FAIR HOUSING DISCRIMINATORY CONDUCT UNDER THE FAIR HOUSING ACT Prohibition Against Discrimination Because of Handicap § 100.205 Design and construction requirements. (a) Covered multifamily dwellings for... accessible to and usable by handicapped persons; (2) All the doors designed to allow passage into and within...

24 CFR 100.205 - Design and construction requirements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... FAIR HOUSING DISCRIMINATORY CONDUCT UNDER THE FAIR HOUSING ACT Prohibition Against Discrimination Because of Handicap § 100.205 Design and construction requirements. (a) Covered multifamily dwellings for... accessible to and usable by handicapped persons; (2) All the doors designed to allow passage into and within...

24 CFR 100.205 - Design and construction requirements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... FAIR HOUSING DISCRIMINATORY CONDUCT UNDER THE FAIR HOUSING ACT Prohibition Against Discrimination Because of Handicap § 100.205 Design and construction requirements. (a) Covered multifamily dwellings for... accessible to and usable by handicapped persons; (2) All the doors designed to allow passage into and within...

24 CFR 100.205 - Design and construction requirements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... FAIR HOUSING DISCRIMINATORY CONDUCT UNDER THE FAIR HOUSING ACT Prohibition Against Discrimination Because of Handicap § 100.205 Design and construction requirements. (a) Covered multifamily dwellings for... accessible to and usable by handicapped persons; (2) All the doors designed to allow passage into and within...

Design, construction, and technical implementation of a web-based interdisciplinary symptom evaluation (WISE) - a heuristic proposal for orofacial pain and temporomandibular disorders.

PubMed

Ettlin, Dominik A; Sommer, Isabelle; Brönnimann, Ben; Maffioletti, Sergio; Scheidt, Jörg; Hou, Mei-Yin; Lukic, Nenad; Steiger, Beat

2016-12-01

Medical symptoms independent of body location burden individuals to varying degrees and may require care by more than one expert. Various paper and computer-based tools exist that aim to comprehensively capture data for optimal clinical management and research. A web-based interdisciplinary symptom evaluation (WISE) was newly designed, constructed, and technically implemented. For worldwide applicability and to avoid copyright infringements, open source software tools and free validated questionnaires available in multiple languages were used. Highly secure data storage limits access strictly to those who use the tool for collecting, storing, and evaluating their data. Concept and implementation is illustrated by a WISE sample tailored for the requirements of a single center in Switzerland providing interdisciplinary care to orofacial pain and temporomandibular disorder patients. By combining a symptom- burden checklist with in-depth questionnaires serving as case-finding instruments, an algorithm was developed that assists in clarifying case complexity and need for targeted expert evaluation. This novel modular approach provides a personalized, response-tailored instrument for the time- and cost-effective collection of symptom-burden focused quantitative data. The tool includes body drawing options and instructional videos. It is applicable for biopsychosocial evaluation in a variety of clinical settings and offers direct feedback by a case report summary. In clinical practice, the new instrument assists in clarifying case complexity and referral need, based on symptom burden and response -tailored case finding. It provides single-case summary reports from a biopsychosocial perspective and includes graphical symptom maps. Secure, centrally stored data collection of anonymous data is possible. The tool enables personalized medicine, facilitates interprofessional education and collaboration, and allows for multicenter patient-reported outcomes research.

Construction and application research of Three-dimensional digital power grid in Southwest China

NASA Astrophysics Data System (ADS)

Zhou, Yang; Zhou, Hong; You, Chuan; Jiang, Li; Xin, Weidong

2018-01-01

With the rapid development of Three-dimensional (3D) digital design technology in the field of power grid construction, the data foundation and technical means of 3D digital power grid construction approaches perfection. 3D digital power grid has gradually developed into an important part of power grid construction and management. In view of the complicated geological conditions in Southwest China and the difficulty in power grid construction and management, this paper is based on the data assets of Southwest power grid, and it aims at establishing a 3D digital power grid in Southwest China to provide effective support for power grid construction and operation management. This paper discusses the data architecture, technical architecture and system design and implementation process of the 3D digital power grid construction through teasing the key technology of 3D digital power grid. The application of power grid data assets management, transmission line corridor planning, geological hazards risk assessment, environmental impact assessment in 3D digital power grid are also discussed and analysed.

7 CFR 1779.42 - Design and construction requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 12 2010-01-01 2010-01-01 false Design and construction requirements. 1779.42 Section 1779.42 Agriculture Regulations of the Department of Agriculture (Continued) RURAL UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE (CONTINUED) WATER AND WASTE DISPOSAL PROGRAMS GUARANTEED LOANS § 1779.42 Design and...

49 CFR 230.66 - Design, construction, and maintenance.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Design, construction, and maintenance. 230.66 Section 230.66 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS Steam Locomotives and Tenders § 230.66 Design,...

Optimized technical and scientific design approach for high performance anticoincidence shields

NASA Astrophysics Data System (ADS)

Graue, Roland; Stuffler, Timo; Monzani, Franco; Bastia, Paolo; Gryksa, Werner; Pahl, Germit

2018-04-01

This paper, "Optimized technical and scientific design approach for high performance anticoincidence shields," was presented as part of International Conference on Space Optics—ICSO 1997, held in Toulouse, France.

Construction of In-house Databases in a Corporation

NASA Astrophysics Data System (ADS)

Kato, Toshio

Osaka Gas Co., Ltd. constructed Osaka Gas Technical Information System (OGTIS) in 1979, which stores and retrieves the in-house technical information and provides even primary materials by unifying optical disk files, facsimile system and so on. The major information sources are technical materials, survey materials, planning documents, design materials, research reports, business tour reports which are all generated inside the Company. At the present moment it amounts to 25,000 items in total adding 1,000 items annually. The data file is updated once in a month and also outputs the abstract journal OGTIS Report monthly. In 1983 it constructed System for International Exchange of Personal Information (SIP) as a subsystem of OGTIS in order to compile SIP database which covers exchange outlines with oversea enterprises or organizations. The data size is 2,600 totally adding about 500 annually with monthly data updating.

How to Improve the Design and Delivery of High-Quality Technical Assistance. Newsletter

ERIC Educational Resources Information Center

Center for Comprehensive School Reform and Improvement, 2005

2005-01-01

Educators often use the term technical assistance to define services delivered or received in the pursuit of school- and district-improvement initiatives. More specifically, technical assistance can be defined as any assistance that identifies, selects, or designs research-based solutions and practices to support school improvement (Mattson &…

Technical writing versus technical writing

NASA Technical Reports Server (NTRS)

Dillingham, J. W.

1981-01-01

Two terms, two job categories, 'technical writer' and 'technical author' are discussed in terms of industrial and business requirements and standards. A distinction between 'technical writing' and technical 'writing' is made. The term 'technical editor' is also considered. Problems inherent in the design of programs to prepare and train students for these jobs are discussed. A closer alliance between industry and academia is suggested as a means of preparing students with competent technical communication skills (especially writing and editing skills) and good technical skills.

Technical Problems of Residential Construction

NASA Astrophysics Data System (ADS)

Nowogońska, Beata; Cibis, Jerzy

2017-10-01

Beauty, utility, durability - these are the features of good architecture and should also be the distinguishing qualities of every residential building. But do beauty and utility remain along with the passing of time? Performance characteristics are an indicator of both, the technical as well as aesthetic state of buildings. Aesthetic needs are in disagreement with the merciless aging process. The beauty of a city is formed not only by the original forms of new residential buildings, but also by existing tenement housing; thus preserving their aesthetics becomes a necessity. Time is continuously passing and along with it, aging intensifies. The aging process is a natural phenomenon for every material. The life expectancy of building materials is also limited. Along with the passing of time, the technical state of residential buildings continuously deteriorates. With the passing of time, the aesthetic values and preferences of users of flats change and the usability of the building decreases. The permanence of buildings, including residential buildings, is shaped not only by the forces of nature but also by activities of humans. A long lifespan is ensured by carrying out ongoing, systematic renovation-repair works. It is thanks to them that buildings derived from past centuries are still being used, and their market attractiveness is not decreasing.

Introduction of Building Information Modeling (BIM) Technologies in Construction

NASA Astrophysics Data System (ADS)

Milyutina, M. A.

2018-05-01

The issues of introduction of building information modeling (BIM) in construction industry are considered in this work. The advantages of this approach and perspectives of the transition to new design technologies, construction process management, and operation in the near future are stated. The importance of development of pilot projects that should identify the ways and means of verification of the regulatory and technical base, as well as economic indicators in the transition to Building Information Technologies in the construction, is noted.

Low-cost satellite mechanical design and construction

NASA Astrophysics Data System (ADS)

Boisjolie-Gair, Nathaniel; Straub, Jeremy

2017-05-01

This paper presents a discussion of techniques for low-cost design and construction of a CubeSat mechanical structure that can serve as a basis for academic programs and a starting point for government, military and commercial large-scale sensing networks, where the cost of each node must be minimized to facilitate system affordability and lower the cost and associated risk of losing any node. Spacecraft Design plays a large role in manufacturability. An intentionally simplified mechanical design is presented which reduces machining costs, as compared to more intricate designs that were considered. Several fabrication approaches are evaluated relative to the low-cost goal.

Quantification of construction waste prevented by BIM-based design validation: Case studies in South Korea.

PubMed

Won, Jongsung; Cheng, Jack C P; Lee, Ghang

2016-03-01

Waste generated in construction and demolition processes comprised around 50% of the solid waste in South Korea in 2013. Many cases show that design validation based on building information modeling (BIM) is an effective means to reduce the amount of construction waste since construction waste is mainly generated due to improper design and unexpected changes in the design and construction phases. However, the amount of construction waste that could be avoided by adopting BIM-based design validation has been unknown. This paper aims to estimate the amount of construction waste prevented by a BIM-based design validation process based on the amount of construction waste that might be generated due to design errors. Two project cases in South Korea were studied in this paper, with 381 and 136 design errors detected, respectively during the BIM-based design validation. Each design error was categorized according to its cause and the likelihood of detection before construction. The case studies show that BIM-based design validation could prevent 4.3-15.2% of construction waste that might have been generated without using BIM. Copyright © 2015 Elsevier Ltd. All rights reserved.

Technical evaluation of a CAD system for orthopaedic shoe-upper design.

PubMed

Lord, M; Foulston, J; Smith, P J

1991-01-01

Computer aided design is now employed routinely in the volume shoe trade. New styles are developed on a three-dimensional image of the last followed by automated pattern generation and engineering. It is suggested that such systems could be useful in the orthopaedic footwear industry although the different requirements for these bespoke products need careful consideration. A clinical trial has been conducted on the Shoemaster (Clarks Shoes) upper design system both to assess its technical capabilities and to consider its role in improvement of service and cosmetic appearance. This particular system works throughout on a three-dimensional representation of the shoe last, which offers particular advantages for integration with shape capture and reproduction. The report concentrates on the technical evaluation to assess (a) its ability to work with unusual last shapes dictated by medical requirements and (b) its potential for integration into a complete computer system for design of both shoe lasts and shoe uppers. The trial indicates that this particular system is promising in both respects.

Design and construction of the astronautics refrigerator magnet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dresner, L.

1994-05-01

This document reports on the design, construction, and testing of a 7-Tesla, 4-in. bore superconducting magnet for use in the Astronautics Refrigerator Experiment. The magnet is a single-strand, layer-wound, potted solenoid wound with Formvar-insulated SSC strands. The magnet was constructed by American Magnetics, Inc. of Oak Ridge and has been installed in the Astronautics Refrigerator Experiment at the Astronautics Technology Center in Madison, Wisconsin.

Design and cloning strategies for constructing shRNA expression vectors

PubMed Central

McIntyre, Glen J; Fanning, Gregory C

2006-01-01

Background Short hairpin RNA (shRNA) encoded within an expression vector has proven an effective means of harnessing the RNA interference (RNAi) pathway in mammalian cells. A survey of the literature revealed that shRNA vector construction can be hindered by high mutation rates and the ensuing sequencing is often problematic. Current options for constructing shRNA vectors include the use of annealed complementary oligonucleotides (74 % of surveyed studies), a PCR approach using hairpin containing primers (22 %) and primer extension of hairpin templates (4 %). Results We considered primer extension the most attractive method in terms of cost. However, in initial experiments we encountered a mutation frequency of 50 % compared to a reported 20 – 40 % for other strategies. By modifying the technique to be an isothermal reaction using the DNA polymerase Phi29, we reduced the error rate to 10 %, making primer extension the most efficient and cost-effective approach tested. We also found that inclusion of a restriction site in the loop could be exploited for confirming construct integrity by automated sequencing, while maintaining intended gene suppression. Conclusion In this study we detail simple improvements for constructing and sequencing shRNA that overcome current limitations. We also compare the advantages of our solutions against proposed alternatives. Our technical modifications will be of tangible benefit to researchers looking for a more efficient and reliable shRNA construction process. PMID:16396676

Reimagining Game Design: Exploring the Design of Constructible Authentic Representations for Science Reasoning

NASA Astrophysics Data System (ADS)

Holbert, Nathan Ryan

Video games have recently become a popular space for educational design due to their interactive and engaging nature and the ubiquity of the gaming experience among youth. Though many researchers argue video games can provide opportunities for learning, educational game design has focused on the classroom rather than the informal settings where games are typically played. Educational games have been moderately successful at achieving learning gains on standardized items, but have failed to show improvements on related but distal problems. In this dissertation I develop and assess a new design principle, called constructible authentic representations for creating informal gaming experiences that players will actively draw on when reasoning in formal and real world contexts. These games provide players with opportunities to engage in meaningful construction with components that integrate relevant concepts to create in-game representations that visually and epistemologically align with related tools and representations utilized in the target domain. In the first phase of the dissertation, I observed children playing popular video games to better understand what in-game representations children attend to and how interactions with these representations contribute to intuitive ideas of encountered STEM content. Results from this study fed into the iterative design of two prototype video games, FormulaT Racing and Particles!, intending to give players useful knowledge resources for reasoning about kinematics and the particulate nature of matter respectively. Designed games encourage players to utilize and refine intuitive ideas about target content through the construction of domain relevant representations. To assess the effectiveness of these designs I conducted two studies of children ages 7-14 playing prototype games in informal settings. An analysis of pre- and post-game clinical interviews, domain specific tasks, and video and logging data of gameplay suggests

Processes in construction of failure management expert systems from device design information

NASA Technical Reports Server (NTRS)

Malin, Jane T.; Lance, Nick

1987-01-01

This paper analyzes the tasks and problem solving methods used by an engineer in constructing a failure management expert system from design information about the device to te diagnosed. An expert test engineer developed a trouble-shooting expert system based on device design information and experience with similar devices, rather than on specific expert knowledge gained from operating the device or troubleshooting its failures. The construction of the expert system was intensively observed and analyzed. This paper characterizes the knowledge, tasks, methods, and design decisions involved in constructing this type of expert system, and makes recommendations concerning tools for aiding and automating construction of such systems.

Design and construction guidelines for thermally insulated concrete pavements.

DOT National Transportation Integrated Search

2013-01-01

The report describes the construction and design of composite pavements as a viable design strategy to use an : asphalt concrete (AC) wearing course as the insulating material and a Portland cement concrete (PCC) structural : layer as the load-carryi...

Technical bulletin on design and construction of crack attenuating mixes (CAM).

DOT National Transportation Integrated Search

2010-02-01

The crack attenuating mix (CAM) is proposed as a thin, long-lasting, cost effective surface mix : for pavement maintenance and preservation. Developed under TxDOT research study 0-5598, : this very fine mix is designed to pass both the current Hambur...

29 CFR 1910.36 - Design and construction requirements for exit routes.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 5 2011-07-01 2011-07-01 false Design and construction requirements for exit routes. 1910.36 Section 1910.36 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR OCCUPATIONAL SAFETY AND HEALTH STANDARDS Means of Egress § 1910.36 Design and construction requirements for exit...

Construct and test scale model box culvert design project.

DOT National Transportation Integrated Search

2010-11-01

The research team at the University of New Mexicos (UNM) hydraulics lab designed, constructed, and : tested a 1:20 scale physical model of a proposed culvert in Jemez Springs, New Mexico. The culvert : design was developed by the New Mexico Depart...

The Design and Construction of a Shiplaunched VTOL Unmanned Air Vehicle

DTIC Science & Technology

1990-06-01

Heppenheimer , T. A ., "The Light Stuff: Burt Rutan Transforms Aircraft Design," High Technolonv. pp. 29-35, December 1986. 16. Alexander, J., Foam...AD-A238 053III 1111 II IIII II OII~ NAVAL POSTGRADUATE SCHOOL Monterey, California OTIC J UL 1 1 1991 THESIS THE DESIGN AND CONSTRUCTION OF A ...8217 € (Include Security Classification) THE DESIGN AND CONSTRUCTION OF A SHIPLAUNCHED VTOL UNMANNED AIR VEHICLE 12. PERSONAL AUTHOR(S) Blanchette, Bryan M

Computer-aided design of nano-filter construction using DNA self-assembly

NASA Astrophysics Data System (ADS)

Mohammadzadegan, Reza; Mohabatkar, Hassan

2007-01-01

Computer-aided design plays a fundamental role in both top-down and bottom-up nano-system fabrication. This paper presents a bottom-up nano-filter patterning process based on DNA self-assembly. In this study we designed a new method to construct fully designed nano-filters with the pores between 5 nm and 9 nm in diameter. Our calculations illustrated that by constructing such a nano-filter we would be able to separate many molecules.

18 CFR 2.13 - Design and construction.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 18 Conservation of Power and Water Resources 1 2013-04-01 2013-04-01 false Design and construction. 2.13 Section 2.13 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF ENERGY GENERAL RULES GENERAL POLICY AND INTERPRETATIONS Statements of General Policy and...

18 CFR 2.13 - Design and construction.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 18 Conservation of Power and Water Resources 1 2014-04-01 2014-04-01 false Design and construction. 2.13 Section 2.13 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF ENERGY GENERAL RULES GENERAL POLICY AND INTERPRETATIONS Statements of General Policy and...

18 CFR 2.13 - Design and construction.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Design and construction. 2.13 Section 2.13 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF ENERGY GENERAL RULES GENERAL POLICY AND INTERPRETATIONS Statements of General Policy and...

18 CFR 2.13 - Design and construction.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 18 Conservation of Power and Water Resources 1 2012-04-01 2012-04-01 false Design and construction. 2.13 Section 2.13 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF ENERGY GENERAL RULES GENERAL POLICY AND INTERPRETATIONS Statements of General Policy and...

Socio-technical systems and interaction design - 21st century relevance.

PubMed

Maguire, Martin

2014-03-01

This paper focuses on the relationship between the socio-technical system and the user-technology interface. It looks at specific aspects of the organisational context such as multiple user roles, job change, work processes and workflows, technical infrastructure, and the challenges they present for the interaction designer. The implications of trends such as more mobile and flexible working, the use of social media, and the growth of the virtual organisation, are also considered. The paper also reviews rapidly evolving technologies such as pervasive systems and artificial intelligence, and the skills that workers will need to engage with them. Copyright © 2013 Elsevier Ltd and The Ergonomics Society. All rights reserved.

10 CFR 433.6 - Sustainable principles for siting, design and construction. [Reserved

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Sustainable principles for siting, design and construction... FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH-RISE RESIDENTIAL BUILDINGS § 433.6 Sustainable principles for siting, design and construction. [Reserved] ...

10 CFR 433.6 - Sustainable principles for siting, design and construction. [Reserved

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Sustainable principles for siting, design and construction... FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH-RISE RESIDENTIAL BUILDINGS § 433.6 Sustainable principles for siting, design and construction. [Reserved] ...

10 CFR 433.6 - Sustainable principles for siting, design and construction. [Reserved

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Sustainable principles for siting, design and construction... FOR NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH-RISE RESIDENTIAL BUILDINGS § 433.6 Sustainable principles for siting, design and construction. [Reserved] ...

Identifying Indicators Related to Constructs for Engineering Design Outcome

ERIC Educational Resources Information Center

Wilhelmsen, Cheryl A.; Dixon, Raymond A.

2016-01-01

This study ranked constructs articulated by Childress and Rhodes (2008) and identified the key indicators for each construct as a starting point to explore what should be included on an instrument to measure the engineering design process and outcomes of students in high schools that use the PLTW and EbDTM curricula in Idaho. A case-study design…

30 CFR 33.20 - Design and construction.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Design and construction. 33.20 Section 33.20 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS DUST COLLECTORS FOR USE IN CONNECTION WITH ROCK DRILLING IN COAL MINES Dust...

30 CFR 33.20 - Design and construction.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Design and construction. 33.20 Section 33.20 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS DUST COLLECTORS FOR USE IN CONNECTION WITH ROCK DRILLING IN COAL MINES Dust...

30 CFR 33.20 - Design and construction.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Design and construction. 33.20 Section 33.20 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS DUST COLLECTORS FOR USE IN CONNECTION WITH ROCK DRILLING IN COAL MINES Dust...

30 CFR 33.20 - Design and construction.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Design and construction. 33.20 Section 33.20 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS DUST COLLECTORS FOR USE IN CONNECTION WITH ROCK DRILLING IN COAL MINES Dust...

30 CFR 33.20 - Design and construction.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Design and construction. 33.20 Section 33.20 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS DUST COLLECTORS FOR USE IN CONNECTION WITH ROCK DRILLING IN COAL MINES Dust...

Transitioning from conceptual design to construction performance specification

NASA Astrophysics Data System (ADS)

Jeffers, Paul; Warner, Mark; Craig, Simon; Hubbard, Robert; Marshall, Heather

2012-09-01

On successful completion of a conceptual design review by a funding agency or customer, there is a transition phase before construction contracts can be placed. The nature of this transition phase depends on the Project's approach to construction and the particular subsystem being considered. There are generically two approaches; project retention of design authority and issuance of build to print contracts, or issuance of subsystem performance specifications with controlled interfaces. This paper relates to the latter where a proof of concept (conceptual or reference design) is translated into performance based sub-system specifications for competitive tender. This translation is not a straightforward process and there are a number of different issues to consider in the process. This paper deals with primarily the Telescope mount and Enclosure subsystems. The main subjects considered in this paper are: • Typical status of design at Conceptual Design Review compared with the desired status of Specifications and Interface Control Documents at Request for Quotation. • Options for capture and tracking of system requirements flow down from science / operating requirements and sub-system requirements, and functional requirements derived from reference design. • Requirements that may come specifically from the contracting approach. • Methods for effective use of reference design work without compromising a performance based specification. • Management of project team's expectation relating to design. • Effects on cost estimates from reference design to actual. This paper is based on experience and lessons learned through this process on both the VISTA and the ATST projects.

Design and construction of PCC pavements. Volume 1, summary of design features and construction practices that influence performance of pavements

DOT National Transportation Integrated Search

1998-04-01

A study has been conducted to evaluate and analyze Portland cement concrete (PCC) pavements in order to develop recommendations for the design and construction of long-lived concrete pavements. In involved a detailed evaluation and analysis of the PC...

Collaborative Learning in Technological Project Design

ERIC Educational Resources Information Center

Hong, Jon-Chao; Yu, Kuang-Chao; Chen, Mei-Yung

2011-01-01

The POWERTECH contest in Taiwan was established in an attempt to promote inventiveness and technology to elementary school pupils. The POWERTECH contest is designed as a collaborative learning system for project design. Project design is comprised of technical processes, which include the construction of an artifact and improvement of its…

10 CFR 435.6 - Sustainable principles for siting, design and construction. [Reserved

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 3 2014-01-01 2014-01-01 false Sustainable principles for siting, design and construction. [Reserved] 435.6 Section 435.6 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY STANDARDS...-Rise Residential Buildings. § 435.6 Sustainable principles for siting, design and construction...

10 CFR 435.6 - Sustainable principles for siting, design and construction. [Reserved

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 3 2013-01-01 2013-01-01 false Sustainable principles for siting, design and construction. [Reserved] 435.6 Section 435.6 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY STANDARDS...-Rise Residential Buildings. § 435.6 Sustainable principles for siting, design and construction...

10 CFR 435.6 - Sustainable principles for siting, design and construction. [Reserved

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 3 2012-01-01 2012-01-01 false Sustainable principles for siting, design and construction. [Reserved] 435.6 Section 435.6 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY STANDARDS...-Rise Residential Buildings. § 435.6 Sustainable principles for siting, design and construction...

49 CFR 192.476 - Internal corrosion control: Design and construction of transmission line.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Internal corrosion control: Design and... STANDARDS Requirements for Corrosion Control § 192.476 Internal corrosion control: Design and construction of transmission line. (a) Design and construction. Except as provided in paragraph (b) of this...

49 CFR 192.476 - Internal corrosion control: Design and construction of transmission line.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 3 2014-10-01 2014-10-01 false Internal corrosion control: Design and... STANDARDS Requirements for Corrosion Control § 192.476 Internal corrosion control: Design and construction of transmission line. (a) Design and construction. Except as provided in paragraph (b) of this...

49 CFR 192.476 - Internal corrosion control: Design and construction of transmission line.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 3 2012-10-01 2012-10-01 false Internal corrosion control: Design and... STANDARDS Requirements for Corrosion Control § 192.476 Internal corrosion control: Design and construction of transmission line. (a) Design and construction. Except as provided in paragraph (b) of this...

49 CFR 192.476 - Internal corrosion control: Design and construction of transmission line.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 3 2013-10-01 2013-10-01 false Internal corrosion control: Design and... STANDARDS Requirements for Corrosion Control § 192.476 Internal corrosion control: Design and construction of transmission line. (a) Design and construction. Except as provided in paragraph (b) of this...

49 CFR 192.476 - Internal corrosion control: Design and construction of transmission line.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 3 2011-10-01 2011-10-01 false Internal corrosion control: Design and... STANDARDS Requirements for Corrosion Control § 192.476 Internal corrosion control: Design and construction of transmission line. (a) Design and construction. Except as provided in paragraph (b) of this...

Constructing a Validity Argument for the Objective Structured Assessment of Technical Skills (OSATS): A Systematic Review of Validity Evidence

ERIC Educational Resources Information Center

Hatala, Rose; Cook, David A.; Brydges, Ryan; Hawkins, Richard

2015-01-01

In order to construct and evaluate the validity argument for the Objective Structured Assessment of Technical Skills (OSATS), based on Kane's framework, we conducted a systematic review. We searched MEDLINE, EMBASE, CINAHL, PsycINFO, ERIC, Web of Science, Scopus, and selected reference lists through February 2013. Working in duplicate, we selected…

Design and Construction Guidance for Community Shelters. FEMA 361.

ERIC Educational Resources Information Center

Federal Emergency Management Agency, Washington, DC.

This manual presents guidance to engineers, architects, building officials, and prospective shelter owners concerning the design and construction of community shelters that will provide protection during tornado and hurricane events. The manual covers two types of community shelters: stand-alone shelters designed to withstand high winds and the…

10 CFR 433.6 - Sustainable principles for siting, design and construction. [Reserved

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 3 2011-01-01 2011-01-01 false Sustainable principles for siting, design and construction. [Reserved] 433.6 Section 433.6 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY STANDARDS FOR THE DESIGN AND CONSTRUCTION OF NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH-RISE RESIDENTIAL...

10 CFR 433.6 - Sustainable principles for siting, design and construction. [Reserved

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Sustainable principles for siting, design and construction. [Reserved] 433.6 Section 433.6 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY EFFICIENCY STANDARDS FOR THE DESIGN AND CONSTRUCTION OF NEW FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH-RISE RESIDENTIAL...

Sortie laboratory, phase B technical summary. [design and operational requirements

NASA Technical Reports Server (NTRS)

1973-01-01

The design and operational requirements which evolved from Sortie Lab (SL) analysis are summarized. A source of requirements for systems is given along with experimental support for the SL, baseline. Basic design data covered include: configuration definition, mission analysis, experimental integration, safety, and logistics. A technical summary outlines characteristics which reflect the influence of the growth in SL capability and the results of the mission and operational analysis. Each of the selected areas is described in terms of objectives, equipment, operational concept, and support requirements.

Mu2e Technical Design Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bartoszek, L.; et al.

Fermi National Accelerator Laboratory and the Mu2e Collaboration, composed of about 155 scientists and engineers from 28 universities and laboratories around the world, have collaborated to create this technical design for a new facility to study charged lepton flavor violation using the existing Department of Energy investment in the Fermilab accelerator complex. Mu2e proposes to measure the ratio of the rate of the neutrinoless, coherent conversion of muons into electrons in the field of a nucleus, relative to the rate of ordinary muon capture on the nucleus. The conversion process is an example of charged lepton flavor violation (CLFV), amore » process that has never been observed experimentally. The significant motivation behind the search for muon-to-electron conversion is discussed in Chapter 3.« less

Instructional Design in Technical Areas. Australian Education Review, No. 43.

ERIC Educational Resources Information Center

Sweller, John

This book details the findings from a research team that used cognitive principles and a large range of experiments to devise a variety of instructional designs. Their recommendations are based on 20 years of objective, published research. Although the program focused on technical subjects, the findings can easily be applied to a range of…

Swarming Robot Design, Construction and Software Implementation

NASA Technical Reports Server (NTRS)

Stolleis, Karl A.

2014-01-01

In this paper is presented an overview of the hardware design, construction overview, software design and software implementation for a small, low-cost robot to be used for swarming robot development. In addition to the work done on the robot, a full simulation of the robotic system was developed using Robot Operating System (ROS) and its associated simulation. The eventual use of the robots will be exploration of evolving behaviors via genetic algorithms and builds on the work done at the University of New Mexico Biological Computation Lab.

Identification of Tools and Techniques to Enhance Interdisciplinary Collaboration During Design and Construction Projects.

PubMed

Keys, Yolanda; Silverman, Susan R; Evans, Jennie

2017-10-01

The purpose of this study was to collect the perceptions of design professionals and clinicians regarding design process success strategies and elements of interprofessional engagement and communication during healthcare design and construction projects. Additional objectives were to gather best practices to maximize clinician engagement and provide tools and techniques to improve interdisciplinary collaboration for future projects. Strategies are needed to enhance the design and construction process and create interactions that benefit not only the project but the individuals working to see its completion. Meaningful interprofessional collaboration is essential to any healthcare design project and making sure the various players communicate is a critical element. This was a qualitative study conducted via an online survey. Respondents included architects, construction managers, interior designers, and healthcare personnel who had recently been involved in a building renovation or new construction project for a healthcare facility. Responses to open-ended questions were analyzed for themes, and descriptive statistics were used to provide insight into participant demographics. Information on the impressions, perceptions, and opportunities related to clinician involvement in design projects was collected from nurses, architects, interior designers, and construction managers. Qualitative analysis revealed themes of clinician input, organizational dynamics, and a variety of communication strategies to be the most frequently mentioned elements of successful interprofessional collaboration. This study validates the need to include clinician input in the design process, to consider the importance of organizational dynamics on design team functioning, and to incorporate effective communication strategies during design and construction projects.

Participatory ergonomics and design of technical assistance.

PubMed

Rodríguez, Claudia Isabel Rojas

2012-01-01

This work describes the experience of application of a procedural initiative, which aimed to identify and address technical assistance needs progressively in therapy and rehabilitation activities. The proposal theoretical axes are the basics of participatory ergonomics and interdisciplinary work, was raised with the intention of addressing important issues for the entire design process including: perception, attention, memory and human being comfort, and the interrelationships that create objects in the context in which they are used. This project was done in collaboration with leading institutes for the rehabilitation of Colombia: Cirec and Roosevelt, through two investigative stages: a first ethnographic stage, during which were observed one hundred forty four (144) procedures of rehabilitation and therapy to build a bank of assistive technology needs, justified on the project observation variables. And a second stage of action research in which they were designed elements that facilitate the implementation of rehabilitation procedures efficiently. Currently being developed experiential situations in different hospitals to examine the reliability of the proposed solutions.

Unique technical innovations for short rotation woody crops research and development

Treesearch

Adam H. Wiese; Ronald S., Jr. Zalesny

2006-01-01

Often technology that is available to conduct short rotation woody crops (SRWC) research is too expensive, difficult to operate, cumbersome, and/or impractical for meeting sample size requirements. Thus, we have designed, constructed, and tested technical innovations that have allowed us to meet our specific experimental needs.

The design and construction of the CAD-1 airship

NASA Technical Reports Server (NTRS)

Kleiner, H. J.; Schneider, R.; Duncan, J. L.

1975-01-01

The background history, design philosophy and Computer application as related to the design of the envelope shape, stress calculations and flight trajectories of the CAD-1 airship, now under construction by Canadian Airship Development Corporation are reported. A three-phase proposal for future development of larger cargo carrying airships is included.

In Search of Design Principles for Developing Digital Learning and Performance Support for a Student Design Task

ERIC Educational Resources Information Center

Bollen, Lars; van der Meij, Hans; Leemkuil, Henny; McKenney, Susan

2015-01-01

A digital learning and performance support environment for university student design tasks was developed. This paper describes on the design rationale, process, and the usage results to arrive at a core set of design principles for the construction of such an environment. We present a collection of organizational, technical, and course-related…

78 FR 40161 - Announcement of Funding Awards for Fiscal Year 2012 Sustainable Construction in Indian Country...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-03

... and cultural aspects of Native American residential design and construction. HUD sought applications in four broad areas: demonstration; technical assistance; curriculum development/training; and...

A Systematic Method of Integrating BIM and Sensor Technology for Sustainable Construction Design

NASA Astrophysics Data System (ADS)

Liu, Zhen; Deng, Zhiyu

2017-10-01

Building Information Modeling (BIM) has received lots of attention of construction field, and sensor technology was applied in construction data collection. This paper developed a method to integrate BIM and sensor technology for sustainable construction design. A brief literature review was conducted to clarify the current development of BIM and sensor technology; then a systematic method for integrating BIM and sensor technology to realize sustainable construction design was put forward; finally a brief discussion and conclusion was given.

Constructions for Children: Projects in Design Technology.

ERIC Educational Resources Information Center

Eichelberger, Barbara; Larson, Connie

This book helps children develop the capability and confidence to design, construct, and evaluate working models. Projects in this book are suitable for students in grades K-4, but may be adapted for older students. Step-by-step explanations for each project are meant as guidelines and completion of the project is not limited to a single correct…

6 CFR 27.120 - Designation of a coordinating official; Consultations and technical assistance.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 6 Domestic Security 1 2014-01-01 2014-01-01 false Designation of a coordinating official; Consultations and technical assistance. 27.120 Section 27.120 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY CHEMICAL FACILITY ANTI-TERRORISM STANDARDS General § 27.120 Designation of a...

6 CFR 27.120 - Designation of a coordinating official; Consultations and technical assistance.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 6 Domestic Security 1 2012-01-01 2012-01-01 false Designation of a coordinating official; Consultations and technical assistance. 27.120 Section 27.120 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY CHEMICAL FACILITY ANTI-TERRORISM STANDARDS General § 27.120 Designation of a...

6 CFR 27.120 - Designation of a coordinating official; Consultations and technical assistance.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 6 Domestic Security 1 2013-01-01 2013-01-01 false Designation of a coordinating official; Consultations and technical assistance. 27.120 Section 27.120 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY CHEMICAL FACILITY ANTI-TERRORISM STANDARDS General § 27.120 Designation of a...

6 CFR 27.120 - Designation of a coordinating official; Consultations and technical assistance.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 6 Domestic Security 1 2011-01-01 2011-01-01 false Designation of a coordinating official; Consultations and technical assistance. 27.120 Section 27.120 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY CHEMICAL FACILITY ANTI-TERRORISM STANDARDS General § 27.120 Designation of a...

Utilization of building information modeling in infrastructure’s design and construction

NASA Astrophysics Data System (ADS)

Zak, Josef; Macadam, Helen

2017-09-01

Building Information Modeling (BIM) is a concept that has gained its place in the design, construction and maintenance of buildings in Czech Republic during recent years. This paper deals with description of usage, applications and potential benefits and disadvantages connected with implementation of BIM principles in the preparation and construction of infrastructure projects. Part of the paper describes the status of BIM implementation in Czech Republic, and there is a review of several virtual design and construction practices in Czech Republic. Examples of best practice are presented from current infrastructure projects. The paper further summarizes experiences with new technologies gained from the application of BIM related workflows. The focus is on the BIM model utilization for the machine control systems on site, quality assurance, quality management and construction management.

Tribal Child Care Facilities: A Guide to Construction and Renovation.

ERIC Educational Resources Information Center

National Child Care Information Center, Vienna, VA.

This document provides technical assistance in addressing major areas of the child care facility construction and renovation process, including conducting a child care community needs assessment, identifying a site, financing costs, developing a business plan, conducting an environmental assessment, building and designing a facility, and hiring…

46 CFR 160.066-5 - Design, construction, and manufacturing requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 6 2011-10-01 2011-10-01 false Design, construction, and manufacturing requirements. 160.066-5 Section 160.066-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Distress Signal for Boats, Red Aerial Pyrotechnic Flare § 160.066-5...

46 CFR 160.066-5 - Design, construction, and manufacturing requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Design, construction, and manufacturing requirements. 160.066-5 Section 160.066-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Distress Signal for Boats, Red Aerial Pyrotechnic Flare § 160.066-5...

46 CFR 160.066-5 - Design, construction, and manufacturing requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Design, construction, and manufacturing requirements. 160.066-5 Section 160.066-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Distress Signal for Boats, Red Aerial Pyrotechnic Flare § 160.066-5...

3D design terrain models for construction plans and GPS control of highway construction equipment.

DOT National Transportation Integrated Search

2010-03-01

Research was conducted with the objectives of 1) identifying and characterizing benefits and technological, institutional, cultural, and : legal impediments associated with adoption of 3D design and construction technologies, identifying strategies t...

How to Construct a Mixed Methods Research Design.

PubMed

Schoonenboom, Judith; Johnson, R Burke

2017-01-01

This article provides researchers with knowledge of how to design a high quality mixed methods research study. To design a mixed study, researchers must understand and carefully consider each of the dimensions of mixed methods design, and always keep an eye on the issue of validity. We explain the seven major design dimensions: purpose, theoretical drive, timing (simultaneity and dependency), point of integration, typological versus interactive design approaches, planned versus emergent design, and design complexity. There also are multiple secondary dimensions that need to be considered during the design process. We explain ten secondary dimensions of design to be considered for each research study. We also provide two case studies showing how the mixed designs were constructed.

Designing water demand management schemes using a socio-technical modelling approach.

PubMed

Baki, Sotiria; Rozos, Evangelos; Makropoulos, Christos

2018-05-01

Although it is now widely acknowledged that urban water systems (UWSs) are complex socio-technical systems and that a shift towards a socio-technical approach is critical in achieving sustainable urban water management, still, more often than not, UWSs are designed using a segmented modelling approach. As such, either the analysis focuses on the description of the purely technical sub-system, without explicitly taking into account the system's dynamic socio-economic processes, or a more interdisciplinary approach is followed, but delivered through relatively coarse models, which often fail to provide a thorough representation of the urban water cycle and hence cannot deliver accurate estimations of the hydrosystem's responses. In this work we propose an integrated modelling approach for the study of the complete socio-technical UWS that also takes into account socio-economic and climatic variability. We have developed an integrated model, which is used to investigate the diffusion of household water conservation technologies and its effects on the UWS, under different socio-economic and climatic scenarios. The integrated model is formed by coupling a System Dynamics model that simulates the water technology adoption process, and the Urban Water Optioneering Tool (UWOT) for the detailed simulation of the urban water cycle. The model and approach are tested and demonstrated in an urban redevelopment area in Athens, Greece under different socio-economic scenarios and policy interventions. It is suggested that the proposed approach can establish quantifiable links between socio-economic change and UWS responses and therefore assist decision makers in designing more effective and resilient long-term strategies for water conservation. Copyright © 2017 Elsevier B.V. All rights reserved.

41 CFR 102-76.15 - What are design and construction services?

Code of Federal Regulations, 2010 CFR

2010-07-01

... construction services are— (a) Site planning and landscape design; (b) Architectural and interior design; and... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false What are design and... Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 76-DESIGN AND...

Design and construction of portable survey meter

NASA Astrophysics Data System (ADS)

Singseeta, W.; Thong-aram, D.; Pencharee, S.

2017-09-01

This work was aimed to design and construction of portable survey meter for radiation dose measuring. The designed system consists of 4 main parts consisting of low voltage power supply, radiation detection, radiation measurement and data display part on android phone. The test results show that the ripple voltage of low voltage power supply is less than 1%, the maximum integral counts are found to be 104 counts per second and the maximum distance of wireless commination between the server and the client is about 10 meter. It was found that the developed system had small size and light weight for portable instrument.

CUORE-0 detector: design, construction and operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alduino, C.; Alfonso, K.; Artusa, D. R.

The CUORE experiment will search for neutrinoless double-beta decay of 130Te with an array of 988 TeO 2 bolometers arranged in 19 towers. CUORE-0, the first tower assembled according to the CUORE procedures, was built and commissioned at Laboratori Nazionali del Gran Sasso, and took data from March 2013 to March 2015. In this study we describe the design, construction and operation of the CUORE-0 experiment, with an emphasis on the improvements made over a predecessor experiment, Cuoricino. Finally, in particular, we demonstrate with CUORE-0 data that the design goals of CUORE are within reach.

CUORE-0 detector: design, construction and operation

DOE PAGES

Alduino, C.; Alfonso, K.; Artusa, D. R.; ...

2016-07-12

The CUORE experiment will search for neutrinoless double-beta decay of 130Te with an array of 988 TeO 2 bolometers arranged in 19 towers. CUORE-0, the first tower assembled according to the CUORE procedures, was built and commissioned at Laboratori Nazionali del Gran Sasso, and took data from March 2013 to March 2015. In this study we describe the design, construction and operation of the CUORE-0 experiment, with an emphasis on the improvements made over a predecessor experiment, Cuoricino. Finally, in particular, we demonstrate with CUORE-0 data that the design goals of CUORE are within reach.

Making sense of complex electronic records: socio-technical design in social care.

PubMed

Wastell, David; White, Sue

2014-03-01

Dealing with complex electronic documentation is an integral part of much contemporary professional work. In this paper, we address the design of electronic records for social care professionals in the UK. Recent reforms in UK child welfare have followed a top-down, managerial approach emphasizing conformance to standard processes. The vicissitudes of a major national IT project, the Integrated Children's System, show the limitations of this approach, in particular the detrimental effect it has had on professional autonomy. Following in the foot-steps of Ken Eason, we argue that socio-technical design, by focussing on innovative applications of technology to support users (rather than the interests of the bureaucracy) offers a more promising alternative. A user-centred design exercise is presented to illustrate this approach in action. A novel interface was developed for handling the heterogeneous bundle of documents which make up the social care record, helping social workers make better sense of case-files. The prototype draws on the metaphor of the dining-room table as a way of overcoming the limitations of the computer display. We conclude that socio-technical thinking engenders a shift in mind-set, opening up a radically different design space compared to current design orthodoxy. Copyright © 2013 Elsevier Ltd and The Ergonomics Society. All rights reserved.

24 CFR 941.203 - Design and construction standards.

Code of Federal Regulations, 2013 CFR

2013-04-01

... national building code, such as Uniform Building Code, Council of American Building Officials Code, or Building Officials Conference of America Code; (2) Applicable State and local laws, codes, ordinances, and... intended to serve. Building design and construction shall strive to encourage in residents a proprietary...

24 CFR 941.203 - Design and construction standards.

Code of Federal Regulations, 2012 CFR

2012-04-01

... national building code, such as Uniform Building Code, Council of American Building Officials Code, or Building Officials Conference of America Code; (2) Applicable State and local laws, codes, ordinances, and... intended to serve. Building design and construction shall strive to encourage in residents a proprietary...

Design, Construction, Demonstration and Delivery of an Automated Narrow Gap Welding System.

DTIC Science & Technology

1982-06-29

DESIGN, CONSTRUCTION, DEMONSTRATION AND DELIVERY OF WE DA4I &NARROW GAP CONTRACT NO. NOOGOO-81-C-E923 TO DAVID TAYLOR NAVAL RESEARCH AND DEVELOPMENT...the automated * Narrow Gap welding process, is the narrow (3/8 - inch), square-butt joint *design. This narrow joint greatly reduces the volume of weld...AD-i45 495 DESIGN CONSTRUCTION DEMONSTRATION AiND DELIVERY OF RN 1/j AUrOMATED NARROW GAP WELDING SYSTEMI() CRC AUTOMATIC WELDING CO HOUSTON TX 29

State of the Art for Design and Construction of Sand Compaction Piles

DTIC Science & Technology

1987-11-01

Walz, Headquarters, US Army Corps of Engineers (HQUSACE), was REMR Technical Monitor. The REMR Overview Committee, consisted of Mr. John R. Nikel ... Wire Vibrator Hopper Casing Pipe Air Line Power Line Sand Skip Bucket Front End Loader Figure 2. Typical equipment used to construct a sand...8217~~~~--­ Rubber Packing Wire Inlet for air to close valve and press sand down ..,...__ Air lnl~ot: Figure 5. Special valve used to seal the casing when

21 CFR 211.42 - Design and construction features.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Design and construction features. 211.42 Section 211.42 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS: GENERAL CURRENT GOOD MANUFACTURING PRACTICE FOR FINISHED PHARMACEUTICALS Buildings and Facilities...

21 CFR 129.20 - Plant construction and design.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 2 2011-04-01 2011-04-01 false Plant construction and design. 129.20 Section 129.20 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION PROCESSING AND BOTTLING OF BOTTLED DRINKING WATER Buildings and Facilities...

21 CFR 129.20 - Plant construction and design.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Plant construction and design. 129.20 Section 129.20 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION PROCESSING AND BOTTLING OF BOTTLED DRINKING WATER Buildings and Facilities...

Design, Construction and Test of Cryogen-Free HTS Coil Structure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hocker, H.; Anerella, M.; Gupta, R.

2011-03-28

This paper will describe design, construction and test results of a cryo-mechanical structure to study coils made with the second generation High Temperature Superconductor (HTS) for the Facility for Rare Isotope Beams (FRIB). A magnet comprised of HTS coils mounted in a vacuum vessel and conduction-cooled with Gifford-McMahon cycle cryocoolers is used to develop and refine design and construction techniques. The study of these techniques and their effect on operations provides a better understanding of the use of cryogen free magnets in future accelerator projects. A cryogen-free, superconducting HTS magnet possesses certain operational advantages over cryogenically cooled, low temperature superconductingmore » magnets.« less

Design and construction of the MicroBooNE detector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Acciarri, R.; Adams, C.; An, R.

This paper describes the design and construction of the MicroBooNE liquid argon time projection chamber and associated systems. MicroBooNE is the first phase of the Short Baseline Neutrino program, located at Fermilab, and will utilize the capabilities of liquid argon detectors to examine a rich assortment of physics topics. In this document details of design specifications, assembly procedures, and acceptance tests are reported.

Design and construction of the MicroBooNE detector

DOE PAGES

Acciarri, R.; Adams, C.; An, R.; ...

2017-02-01

This paper describes the design and construction of the MicroBooNE liquid argon time projection chamber and associated systems. MicroBooNE is the first phase of the Short Baseline Neutrino program, located at Fermilab, and will utilize the capabilities of liquid argon detectors to examine a rich assortment of physics topics. In this document details of design specifications, assembly procedures, and acceptance tests are reported.

Technical Assistance and Training from the Document Design Project. Final Report.

ERIC Educational Resources Information Center

American Institutes for Research, Washington, DC.

Contained in this report is a description of the technical assistance and training phase of the Document Design Project, a program funded by the National Institute of Education and intended to address and correct the readability problems posed by public documents. The first section of the report provides background material on the assistance and…

Students' Construction of External Representations in Design-Based Learning Situations

ERIC Educational Resources Information Center

de Vries, Erica

2006-01-01

This article develops a theoretical framework for the study of students' construction of mixed multiple external representations in design-based learning situations involving an adaptation of professional tasks and tools to a classroom setting. The framework draws on research on professional design processes and on learning with multiple external…

Railway project design and construction (CEE 411) course updates.

DOT National Transportation Integrated Search

2017-01-20

Course CEE 411 "Railway Project Design and Construction" is a cornerstone of the railway : engineering education program developed by the Rail Transportation and Engineering Center : (RailTEC) at the University of Illinois at Urbana-Champaign (UIUC)....

Comparative Study On The Ethical Perceptions Of Contractors And Designers In The China Construction Industry

NASA Astrophysics Data System (ADS)

Kang, Byung Gyoo; Long, Kaiwen; Zhang, Cheng; Li Hao, Jian

2017-12-01

Ethics is becoming one of the most important requirements for successful business in the 21st century. The construction industry cannot be exceptional from this trend. However construction ethics management requires different approaches from other industries, as the products of the industry are construction projects which are completely different from mass production. Contractors and designers are two major participants in construction projects. The roles and responsibilities of these two project stakeholders decisively influence all aspects of construction project. Practically ethical perceptions of contractors and designers are one of main aspects to be considered for the effective and efficient management of ethics for the construction industry. This research has investigated the ethical perceptions of contractors and designers in the China construction industry. A questionnaire survey which contains 15 ethical issues and 6 demographic factors has been conducted. 170 construction professionals from construction companies and consulting companies have been participated in this survey. These 15 ethical issues are ranked in terms of seriousness, frequency and importance for both contractors and designers as a single group to understand the overall perceptions in the industry. The analysis has also been conducted for contractors and designers respectively to make comparisons between them. The top three serious ethical issues in the industry are ‘Bribery and corruption’, ‘Failure to practice whistle-blowing’ and ‘Improper bidding practices’. Contractors and designers showed similar outcomes for the top five important ethical issues. But for the middle ranged ethical issues, they showed some differences. Further researches are required to identify the causes of the similarity and differences.

Performance of Building Technology Graduates in the Construction Industry in Ghana

ERIC Educational Resources Information Center

Ayarkwa, J.; Dansoh, Ayirebi; Adinyira, E.; Amoah, P.

2011-01-01

Purpose: This paper aims to assess the perception of the Ghanaian construction industry of the performance of entry-level building technology graduates. Also, other non-technical skills or attributes expected from building technology graduates are to be compared with the actual proficiency of the graduates. Design/methodology/approach: The…

Implementation of sustainability in bridge design, construction and maintenance.

DOT National Transportation Integrated Search

2012-12-01

The focus of this research is to develop a framework for more sustainable design and construction : processes for new bridges, and sustainable maintenance practices for existing bridges. The framework : includes a green rating system for bridges. The...

46 CFR 98.25-10 - Design and construction of cargo tanks.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Anhydrous Ammonia in Bulk § 98.25-10 Design and construction of cargo tanks. (a) The cargo tanks shall meet... the liquid ammonia is maintained below the normal atmospheric temperatures, shall be designed for a...

46 CFR 98.25-10 - Design and construction of cargo tanks.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Anhydrous Ammonia in Bulk § 98.25-10 Design and construction of cargo tanks. (a) The cargo tanks shall meet... the liquid ammonia is maintained below the normal atmospheric temperatures, shall be designed for a...

46 CFR 98.25-10 - Design and construction of cargo tanks.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Anhydrous Ammonia in Bulk § 98.25-10 Design and construction of cargo tanks. (a) The cargo tanks shall meet... the liquid ammonia is maintained below the normal atmospheric temperatures, shall be designed for a...

46 CFR 162.027-2 - Design, construction, testing and marking requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 6 2011-10-01 2011-10-01 false Design, construction, testing and marking requirements. 162.027-2 Section 162.027-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Combination Solid Stream and Water Spray Firehose Nozzles §...

46 CFR 162.027-2 - Design, construction, testing and marking requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Design, construction, testing and marking requirements. 162.027-2 Section 162.027-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Combination Solid Stream and Water Spray Firehose Nozzles §...

46 CFR 162.027-2 - Design, construction, testing and marking requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Design, construction, testing and marking requirements. 162.027-2 Section 162.027-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Combination Solid Stream and Water Spray Firehose Nozzles §...

Teaching Sustainable Design Using BIM and Project-Based Energy Simulations

ERIC Educational Resources Information Center

Shen, Zhigang; Jensen, Wayne; Wentz, Timothy; Fischer, Bruce

2012-01-01

The cross-disciplinary nature of energy-efficient building design has created many challenges for architecture, engineering and construction instructors. One of the technical challenges in teaching sustainable building design is enabling students to quantitatively understand how different building designs affect a building's energy performance.…

Design and Assessment of an Associate Degree-Level Plant Operations Technical Education Program

NASA Astrophysics Data System (ADS)

Selwitz, Jason Lawrence

Research was undertaken to develop and evaluate an associate degree-level technical education program in Plant Operations oriented towards training students in applied science, technology, engineering, and mathematics (STEM) skills and knowledge relevant to a spectrum of processing industries. This work focuses on four aspects of the curriculum and course development and evaluation research. First, the context of, and impetus for, what was formerly called vocational education, now referred to as technical or workforce education, is provided. Second, the research that was undertaken to design and evaluate an associate degree-level STEM workforce education program is described. Third, the adaptation of a student self-assessment of learning gains instrument is reviewed, and an analysis of the resulting data using an adapted logic model is provided, to evaluate the extent to which instructional approaches, in two process control/improvement-focused courses, were effective in meeting course-level intended learning outcomes. Finally, eight integrative multiscale exercises were designed from two example process systems, wastewater treatment and fast pyrolysis. The integrative exercises are intended for use as tools to accelerate the formation of an operator-technician's multiscale vision of systems, unit operations, underlying processes, and fundamental reactions relevant to multiple industries. Community and technical colleges serve a vital function in STEM education by training workers for medium- and high-skilled technical careers and providing employers the labor necessary to operate and maintain thriving business ventures. Through development of the curricular, course, and assessment-related instruments and tools, this research helps ensure associate degree-level technical education programs can engage in a continual process of program evaluation and improvement.

Pedagogical, Social and Technical Designs of a Blended Synchronous Learning Environment

ERIC Educational Resources Information Center

Wang, Qiyun; Huang, Changqin

2018-01-01

In this study, a blended synchronous learning environment (BSLE) was designed from pedagogical, social and technical perspectives. It was created for a group of master's students to attend lessons in the classroom and at the same time allow a few of them to join the identical sessions using video conferencing from different sites. The purpose of…

DESIGN, CONSTRUCTION, AND EVALUATION OF A CHAMBER FOR AEROBIOLOGY

EPA Science Inventory

A chamber was designed and constructed for aeromicrobiology applications. An ultraviolet (UV) radiation source was incorporated to sterilize the chamber between trials. Twelve bacterial species originally isolated from air samples and obtained from the American Type Culture Colle...

Task-Based EFL Language Teaching with Procedural Information Design in a Technical Writing Context

ERIC Educational Resources Information Center

Roy, Debopriyo

2017-01-01

Task-based language learning (TBLL) has heavily influenced syllabus design, classroom teaching, and learner assessment in a foreign or second language teaching context. In this English as foreign language (EFL) learning environment, the paper discussed an innovative language learning pedagogy based on design education and technical writing. In…

Baseball Stadium Design: Teaching Engineering Economics and Technical Communication in a Multi-Disciplinary Setting.

ERIC Educational Resources Information Center

Dahm, Kevin; Newell, James

2001-01-01

Reports on a course at Rowan University, based on the economic design of a baseball stadium, that offers an introduction to multidisciplinary engineering design linked with formal training in technical communication. Addresses four pedagogical goals: (1) developing public speaking skills in a realistic, business setting; (2) giving students…

Experimental Setup for Evaluation of the Protective Technical Measures Against the Slopes Degradation Along Linear Construction Sites

NASA Astrophysics Data System (ADS)

Kavka, Petr; Zumr, David; Neumann, Martin; Lidmila, Martin; Dufka, Dušan

2017-04-01

Soil erosion of the slopes along the linear construction sites, such as railroads, roads, pipelines or watercourses, is usually underestimated by the construction companies and controlling authorities. But under certain circumstances, when the construction site is not maintained and protected properly, a large amounts of soil may be transported from the sites to the surrounding environment during the intensive rainfall. Transported sediment, often carrying adsorbed pollutants, may reach watercourses and cause water recipient siltation and pollution. Within the applied research project we investigate ways of low cost, quick and easy technical measures that would help to protect the slopes against the splash erosion, rills development and sliding. The methodology is based on testing of various permeable covers, sheets, anchoring and patchy vegetation on a plot and hillslope scales. In this contribution we will present the experimental plot setup, consisting of large soil blocks encapsulated in the monitored steel containers and nozzle rainfall simulator. The presentation is funded by the Technological Agency of the Czech Republic (research project TH02030428) and an internal student CTU grant.

46 CFR 163.002-3 - Applicable technical regulations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Applicable technical regulations. 163.002-3 Section 163.002-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL CONSTRUCTION Pilot Hoist § 163.002-3 Applicable technical regulations...

The use of modern measurement techniques for designing pro ecological constructions

NASA Astrophysics Data System (ADS)

Wieczorowski, Michał; Gapiński, Bartosz; Szymański, Maciej; Rękas, Artur

2017-10-01

In the paper some possibilities of application modern length and angle metrology techniques to design constructions that support ecology were presented. The paper is based on a project where a lighter bus and train car seat was developed. Different options were presented including static and dynamic photogrammetry, computed tomography and thermography. Research related with dynamic behaviour of designed structures gave input to determine deformation of a seat and passengers sitting on it during communication accidents. Works connected to strength of construction elements made it possible to optimize its dimensions maintaining proper durability. Metrological actions taken in relation to production machines and equipment enabled to better recognize phenomena that take place during manufacturing process and to correct its parameters, what in turns also contributed to slim down the construction.

Design as Knowledge Construction: Constructing Knowledge of Design

ERIC Educational Resources Information Center

Cennamo, Katherine C.

2004-01-01

In this article, I present a model of instructional design that has evolved from analysis and reflection on the process of designing materials for constructivist learning environments. I observed how we addressed the critical questions for instructional design, comparing the process to traditional instructional design models and to my emerging…

A High School Level Course On Robot Design And Construction

NASA Astrophysics Data System (ADS)

Sadler, Paul M.; Crandall, Jack L.

1984-02-01

The Robotics Design and Construction Class at Sehome High School was developed to offer gifted and/or highly motivated students an in-depth introduction to a modern engineering topic. The course includes instruction in basic electronics, digital and radio electronics, construction skills, robotics literacy, construction of the HERO 1 Heathkit Robot, computer/ robot programming, and voice synthesis. A key element which leads to the success of the course is the involvement of various community assets including manpower and financial assistance. The instructors included a physics/electronics teacher, a computer science teacher, two retired engineers, and an electronics technician.

DETAIL OF PLAQUE WITH ADDITIONAL DESIGN AND CONSTRUCTION INFORMATION, SOUTHEAST ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL OF PLAQUE WITH ADDITIONAL DESIGN AND CONSTRUCTION INFORMATION, SOUTHEAST ABUTMENT - Connecticut Avenue Bridge, Spans Rock Creek & Potomac Parkway at Connecticut Avenue, Washington, District of Columbia, DC

REQUIREMENTS FOR HAZARDOUS WASTE LANDFILL DESIGN, CONSTRUCTION AND CLOSURE

EPA Science Inventory

This publication contains edited versions of the material presented at ten Technology Transfer seminars conducted in 1988 on this subject. Sections are included on design of clay and flexible membrane liners, leachate collector systems, and landfill covers. Construction quality a...

Technical Feasibility Study for Zero Energy K-12 Schools

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pless, Shanti D.; Torcellini, Paul A.; Bonnema, Eric

A simulation-based technical feasibility study was completed to show the types of technologies required to achieve ZEB status with this building type. These technologies are prioritized across the building's subsystem such that design teams can readily integrate the ideas. Energy use intensity (EUI) targets were established for U.S. climate zones such that K-12 schools can be zero-ready or can procure solar panels or other renewable energy production sources to meet the zero energy building definition. Results showed that it is possible for K-12 schools to achieve zero energy when the EUI is between 20 and 26 kBtu/ft2/yr. Temperate climates requiredmore » a smaller percentage of solar panel coverage than very hot or very cold climates. The paper provides a foundation for technically achieving zero energy schools with a vision of transforming the school construction market to mainstream zero energy buildings within typical construction budgets.« less

Under Construction: An Experiential Exercise Illustrating Elements of Work Design

ERIC Educational Resources Information Center

Donovan, Kimberly M.; Fluegge-Woolf, Erin R.

2015-01-01

The Under Construction Exercise was developed by the authors to highlight key factors of work design that when implemented among the work group or entire organization can lead to an environment conducive to fostering satisfaction and motivation. In the exercise, groups are assigned to one of four different conditions that are designed to emulate…

Reinforce Design and Construction Issues with a Comprehensive Laboratory Project.

ERIC Educational Resources Information Center

Schemmel, John J.

In 1996, a comprehensive project was introduced in the first course of Reinforced Concrete Design, CVEG 4303 at the University of Arkansas. The primary purpose of this project was to highlight issues related to the construction of reinforced concrete elements. This semester-long project involves the design, fabrication, and testing of 8-foot long…

Gene composer: database software for protein construct design, codon engineering, and gene synthesis.

PubMed

Lorimer, Don; Raymond, Amy; Walchli, John; Mixon, Mark; Barrow, Adrienne; Wallace, Ellen; Grice, Rena; Burgin, Alex; Stewart, Lance

2009-04-21

To improve efficiency in high throughput protein structure determination, we have developed a database software package, Gene Composer, which facilitates the information-rich design of protein constructs and their codon engineered synthetic gene sequences. With its modular workflow design and numerous graphical user interfaces, Gene Composer enables researchers to perform all common bio-informatics steps used in modern structure guided protein engineering and synthetic gene engineering. An interactive Alignment Viewer allows the researcher to simultaneously visualize sequence conservation in the context of known protein secondary structure, ligand contacts, water contacts, crystal contacts, B-factors, solvent accessible area, residue property type and several other useful property views. The Construct Design Module enables the facile design of novel protein constructs with altered N- and C-termini, internal insertions or deletions, point mutations, and desired affinity tags. The modifications can be combined and permuted into multiple protein constructs, and then virtually cloned in silico into defined expression vectors. The Gene Design Module uses a protein-to-gene algorithm that automates the back-translation of a protein amino acid sequence into a codon engineered nucleic acid gene sequence according to a selected codon usage table with minimal codon usage threshold, defined G:C% content, and desired sequence features achieved through synonymous codon selection that is optimized for the intended expression system. The gene-to-oligo algorithm of the Gene Design Module plans out all of the required overlapping oligonucleotides and mutagenic primers needed to synthesize the desired gene constructs by PCR, and for physically cloning them into selected vectors by the most popular subcloning strategies. We present a complete description of Gene Composer functionality, and an efficient PCR-based synthetic gene assembly procedure with mis-match specific endonuclease

Gene Composer: database software for protein construct design, codon engineering, and gene synthesis

PubMed Central

Lorimer, Don; Raymond, Amy; Walchli, John; Mixon, Mark; Barrow, Adrienne; Wallace, Ellen; Grice, Rena; Burgin, Alex; Stewart, Lance

2009-01-01

Background To improve efficiency in high throughput protein structure determination, we have developed a database software package, Gene Composer, which facilitates the information-rich design of protein constructs and their codon engineered synthetic gene sequences. With its modular workflow design and numerous graphical user interfaces, Gene Composer enables researchers to perform all common bio-informatics steps used in modern structure guided protein engineering and synthetic gene engineering. Results An interactive Alignment Viewer allows the researcher to simultaneously visualize sequence conservation in the context of known protein secondary structure, ligand contacts, water contacts, crystal contacts, B-factors, solvent accessible area, residue property type and several other useful property views. The Construct Design Module enables the facile design of novel protein constructs with altered N- and C-termini, internal insertions or deletions, point mutations, and desired affinity tags. The modifications can be combined and permuted into multiple protein constructs, and then virtually cloned in silico into defined expression vectors. The Gene Design Module uses a protein-to-gene algorithm that automates the back-translation of a protein amino acid sequence into a codon engineered nucleic acid gene sequence according to a selected codon usage table with minimal codon usage threshold, defined G:C% content, and desired sequence features achieved through synonymous codon selection that is optimized for the intended expression system. The gene-to-oligo algorithm of the Gene Design Module plans out all of the required overlapping oligonucleotides and mutagenic primers needed to synthesize the desired gene constructs by PCR, and for physically cloning them into selected vectors by the most popular subcloning strategies. Conclusion We present a complete description of Gene Composer functionality, and an efficient PCR-based synthetic gene assembly procedure with mis

19 CFR 115.65 - Technical requirements for road vehicles by design type.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 19 Customs Duties 1 2012-04-01 2012-04-01 false Technical requirements for road vehicles by design type. 115.65 Section 115.65 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO...

19 CFR 115.65 - Technical requirements for road vehicles by design type.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 19 Customs Duties 1 2011-04-01 2011-04-01 false Technical requirements for road vehicles by design type. 115.65 Section 115.65 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO...

19 CFR 115.65 - Technical requirements for road vehicles by design type.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 19 Customs Duties 1 2013-04-01 2013-04-01 false Technical requirements for road vehicles by design type. 115.65 Section 115.65 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO...

19 CFR 115.65 - Technical requirements for road vehicles by design type.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 19 Customs Duties 1 2014-04-01 2014-04-01 false Technical requirements for road vehicles by design type. 115.65 Section 115.65 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO...

19 CFR 115.65 - Technical requirements for road vehicles by design type.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Technical requirements for road vehicles by design type. 115.65 Section 115.65 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO...

Technical Support Document: 50% Energy Savings Design Technology Packages for Highway Lodging Buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Wei; Gowri, Krishnan; Lane, Michael D.

2009-09-28

This Technical Support Document (TSD) describes the process, methodology and assumptions for development of the 50% Energy Savings Design Technology Packages for Highway Lodging Buildings, a design guidance document intended to provide recommendations for achieving 50% energy savings in highway lodging properties over the energy-efficiency levels contained in ANSI/ASHRAE/IESNA Standard 90.1-2004, Energy Standard for Buildings Except Low-Rise Residential Buildings.

Use Of Infrared Thermography For The Identification Of Design And Construction Faults In Buildings

NASA Astrophysics Data System (ADS)

Seeber, Stephen A.

1984-03-01

Many design and construction details can affect building energy consumption in unex-pected ways. Further, design and construction errors can increase building energy consumption, result in discomfort to building occupants and cause structural damage to the building. Infrared inspections can easily evaluate the energy efficiency of various aspects of a building's design and identify flaws that might otherwise be detected as a result of occupants' complaints or damage to the building's mechanical or structural systems. Infrared thermography can be used by the architect to evaluate his designs and by the contractor to control the quality of construction. This paper discusses a number of issues that can help determine the effectiveness of infrared building surveys. Following this, three case stud-ies will be presented to illustrate design flaws that were detected through infrared build-ing surveys.

Designable DNA-binding domains enable construction of logic circuits in mammalian cells.

PubMed

Gaber, Rok; Lebar, Tina; Majerle, Andreja; Šter, Branko; Dobnikar, Andrej; Benčina, Mojca; Jerala, Roman

2014-03-01

Electronic computer circuits consisting of a large number of connected logic gates of the same type, such as NOR, can be easily fabricated and can implement any logic function. In contrast, designed genetic circuits must employ orthogonal information mediators owing to free diffusion within the cell. Combinatorial diversity and orthogonality can be provided by designable DNA- binding domains. Here, we employed the transcription activator-like repressors to optimize the construction of orthogonal functionally complete NOR gates to construct logic circuits. We used transient transfection to implement all 16 two-input logic functions from combinations of the same type of NOR gates within mammalian cells. Additionally, we present a genetic logic circuit where one input is used to select between an AND and OR function to process the data input using the same circuit. This demonstrates the potential of designable modular transcription factors for the construction of complex biological information-processing devices.

Design, simulation and construction of the Taban tokamak

NASA Astrophysics Data System (ADS)

H, R. MIRZAEI; R, AMROLLAHI

2018-04-01

This paper describes the design and construction of the Taban tokamak, which is located in Amirkabir University of Technology, Tehran, Iran. The Taban tokamak was designed for plasma investigation. The design, simulation and construction of essential parts of the Taban tokamak such as the toroidal field (TF) system, ohmic heating (OH) system and equilibrium field system and their power supplies are presented. For the Taban tokamak, the toroidal magnetic coil was designed to produce a maximum field of 0.7 T at R = 0.45 m. The power supply of the TF was a 130 kJ, 0–10 kV capacitor bank. Ripples of toroidal magnetic field at the plasma edge and plasma center are 0.2% and 0.014%, respectively. For the OH system with 3 kA current, the stray field in the plasma region is less than 40 G over 80% of the plasma volume. The power supply of the OH system consists of two stages, as follows. The fast bank stage is a 120 μF, 0–5 kV capacitor that produces 2.5 kA in 400 μs and the slow bank stage is 93 mF, 600 V that can produce a maximum of 3 kA. The equilibrium system can produce uniform magnetic field at plasma volume. This system’s power supply, like the OH system, consists of two stages, so that the fast bank stage is 500 μF, 800 V and the slow bank stage is 110 mF, 200 V.

Study on construction technology of metro tunnel under a glass curtain wall

NASA Astrophysics Data System (ADS)

Zhang, Jian; Yu, Deqiang

2018-03-01

To ensure the safety of the glass curtain wall building above loess tunnel and get an optimal scheme, an elastic-plastic FEM model is established to simulate three reinforcement schemes based on a tunnel section in Xi’an Metro Line 3. The results show that the settlement value of the optimal scheme is reduced by 69.89% compared with the drainage measures, and the uneven settlement value is reduced by 57.5%. The construction points, technical processes and technical indexes of the optimal scheme are introduced. According to the actual project, the cumulative settlement of the building under construction is 16mm, which meets the control standards. According to the actual project, the cumulative settlement of the glass curtain wall building is 16mm, which meets the control standards. The reinforcement scheme can provide some reference for the design and construction of the metro in loess area.

Review of Environmental Consequences of Waterway Design and Construction Practices as of 1979.

DTIC Science & Technology

1982-04-01

AD-A118 07Th VANDERISILT UNIV NASHVILLE I TN F/ ,2 REVIEW OF ENVIRONMENTAL CONSEQUENCES OF WATERWAY DESIGN AND CON-ETC(U U CLASSIFIED APR 82 E L... DESIGN AND CONSTRUCTION PRACTICES AS OF 1979 8. PERFORMING ORG. REPORT NUMEER 7. AUTHOR(q) S. CONTRACT OR GRANT NUMUER(t) Edward L. Thackston...numF*-" a I~mOlPi lt block ninr) >. Waterway projects designed and constructed by the Corps of Engineers (CE) include dikes, revetments, levees, and

UXO Engineering Design. Technical Specification and ConceptualDesign

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beche, J-F.; Doolittle, L.; Greer, J.

2005-04-23

The design and fabrication of the UXO detector has numerous challenges and is an important component to the success of this study. This section describes the overall engineering approach, as well as some of the technical details that brought us to the present design. In general, an array of sensor coils is measuring the signal generated by the UXO object in response to a stimulation provided by the driver coil. The information related to the location, shape and properties of the object is derived from the analysis of the measured data. Each sensor coil is instrumented with a waveform digitizermore » operating at a nominal digitization rate of 100 kSamples per second. The sensor coils record both the large transient pulse of the driver coil and the UXO object response pulse. The latter is smaller in amplitude and must be extracted from the large transient signal. The resolution required is 16 bits over a dynamic range of at least 140 dB. The useful signal bandwidth of the application extends from DC to 40 kHz. The low distortion of each component is crucial in order to maintain an excellent linearity over the full dynamic range and to minimize the calibration procedure. The electronics must be made as compact as possible so that the response of its metallic parts has a minimum signature response. Also because of a field system portability requirement, the power consumption of the instrument must be kept as low as possible. The theory and results of numerical and experimental studies that led to the proof-of-principle multitransmitter-multireceiver Active ElectroMagnetic (AEM) system, that can not only accurately detect but also characterize and discriminate UXO targets, are summarized in LBNL report-53962: ''Detection and Classification of Buried Metallic Objects, UX-1225''.« less

LSST summit facility construction progress report: reacting to design refinements and field conditions

NASA Astrophysics Data System (ADS)

Barr, Jeffrey D.; Gressler, William; Sebag, Jacques; Seriche, Jaime; Serrano, Eduardo

2016-07-01

The civil work, site infrastructure and buildings for the summit facility of the Large Synoptic Survey Telescope (LSST) are among the first major elements that need to be designed, bid and constructed to support the subsequent integration of the dome, telescope, optics, camera and supporting systems. As the contracts for those other major subsystems now move forward under the management of the LSST Telescope and Site (T and S) team, there has been inevitable and beneficial evolution in their designs, which has resulted in significant modifications to the facility and infrastructure. The earliest design requirements for the LSST summit facility were first documented in 2005, its contracted full design was initiated in 2010, and construction began in January, 2015. During that entire development period, and extending now roughly halfway through construction, there continue to be necessary modifications to the facility design resulting from the refinement of interfaces to other major elements of the LSST project and now, during construction, due to unanticipated field conditions. Changes from evolving interfaces have principally involved the telescope mount, the dome and mirror handling/coating facilities which have included significant variations in mass, dimensions, heat loads and anchorage conditions. Modifications related to field conditions have included specifying and testing alternative methods of excavation and contending with the lack of competent rock substrate where it was predicted to be. While these and other necessary changes are somewhat specific to the LSST project and site, they also exemplify inherent challenges related to the typical timeline for the design and construction of astronomical observatory support facilities relative to the overall development of the project.

Greenroads : a sustainability performance metric for roadway design and construction.

DOT National Transportation Integrated Search

2009-11-01

Greenroads is a performance metric for quantifying sustainable practices associated with roadway design and construction. Sustainability is defined as having seven key components: ecology, equity, economy, extent, expectations, experience and exposur...

Technical note: Design flood under hydrological uncertainty

NASA Astrophysics Data System (ADS)

Botto, Anna; Ganora, Daniele; Claps, Pierluigi; Laio, Francesco

2017-07-01

Planning and verification of hydraulic infrastructures require a design estimate of hydrologic variables, usually provided by frequency analysis, and neglecting hydrologic uncertainty. However, when hydrologic uncertainty is accounted for, the design flood value for a specific return period is no longer a unique value, but is represented by a distribution of values. As a consequence, the design flood is no longer univocally defined, making the design process undetermined. The Uncertainty Compliant Design Flood Estimation (UNCODE) procedure is a novel approach that, starting from a range of possible design flood estimates obtained in uncertain conditions, converges to a single design value. This is obtained through a cost-benefit criterion with additional constraints that is numerically solved in a simulation framework. This paper contributes to promoting a practical use of the UNCODE procedure without resorting to numerical computation. A modified procedure is proposed by using a correction coefficient that modifies the standard (i.e., uncertainty-free) design value on the basis of sample length and return period only. The procedure is robust and parsimonious, as it does not require additional parameters with respect to the traditional uncertainty-free analysis. Simple equations to compute the correction term are provided for a number of probability distributions commonly used to represent the flood frequency curve. The UNCODE procedure, when coupled with this simple correction factor, provides a robust way to manage the hydrologic uncertainty and to go beyond the use of traditional safety factors. With all the other parameters being equal, an increase in the sample length reduces the correction factor, and thus the construction costs, while still keeping the same safety level.

Design and construction of the Discovery Channel Telescope enclosure

NASA Astrophysics Data System (ADS)

Marshall, Heather K.; Teran, Jose U.; Bond, Kevin

2010-07-01

The Discovery Channel Telescope (DCT) is a project of Lowell Observatory, undertaken with support from Discovery Communications, Inc., to design and construct a 4-meter class telescope and support facility on a site approximately 40 miles southeast of Flagstaff, Arizona. The Discovery Channel Telescope Enclosure was completed in November, 2009. The DCT Enclosure is an octagonal steel structure with insulated composite panel skin. The structure rotates on sixteen compliant bogie assemblies attached to the stationary facility. The shutter is composed of two independently actuated, bi-parting structures that provide a viewing aperture. To improve seeing, the skin is covered with adhesive aluminum foil tape and the enclosed observing area is passively ventilated via rollup doors. The observing area can also be actively ventilated using a downdraft fan, and there are provisions for upgrades to active air conditioning. The enclosure also includes operational equipment such as a bridge crane, personnel lift, and access platforms. This paper discusses some of the design trades as well as the construction challenges and lessons learned by the DCT Project, its designer M3 Engineering and Technology Corporation (M3), and its general contractor, Building and Engineering Contractors, Southwest (BEC Southwest).

Space construction activities

NASA Technical Reports Server (NTRS)

1991-01-01

The Center for Space Construction at the University of Colorado at Boulder was established in 1988 as a University Space Engineering Research Center. The mission of the Center is to conduct interdisciplinary engineering research which is critical to the construction of future space structures and systems and to educate students who will have the vision and technical skills to successfully lead future space construction activities. The research activities are currently organized around two central projects: Orbital Construction and Lunar Construction. Summaries of the research projects are included.

Design and Construction of Simple, Nitrogen-Laser-Pumped, Tunable Dye Lasers

ERIC Educational Resources Information Center

Hilborn, Robert C.

1978-01-01

The basic physical principles of dye lasers are discussed and used to analyze the design and operation of tunable dye lasers pumped by pulsed nitrogen lasers. Details of the design and construction of these dye lasers are presented. Some simple demonstration experiments are described. (BB)

Review of qualitative approaches for the construction industry: designing a risk management toolbox.

PubMed

Zalk, David M; Spee, Ton; Gillen, Matt; Lentz, Thomas J; Garrod, Andrew; Evans, Paul; Swuste, Paul

2011-06-01

This paper presents the framework and protocol design for a construction industry risk management toolbox. The construction industry needs a comprehensive, systematic approach to assess and control occupational risks. These risks span several professional health and safety disciplines, emphasized by multiple international occupational research agenda projects including: falls, electrocution, noise, silica, welding fumes, and musculoskeletal disorders. Yet, the International Social Security Association says, "whereas progress has been made in safety and health, the construction industry is still a high risk sector." Small- and medium-sized enterprises (SMEs) employ about 80% of the world's construction workers. In recent years a strategy for qualitative occupational risk management, known as Control Banding (CB) has gained international attention as a simplified approach for reducing work-related risks. CB groups hazards into stratified risk 'bands', identifying commensurate controls to reduce the level of risk and promote worker health and safety. We review these qualitative solutions-based approaches and identify strengths and weaknesses toward designing a simplified CB 'toolbox' approach for use by SMEs in construction trades. This toolbox design proposal includes international input on multidisciplinary approaches for performing a qualitative risk assessment determining a risk 'band' for a given project. Risk bands are used to identify the appropriate level of training to oversee construction work, leading to commensurate and appropriate control methods to perform the work safely. The Construction Toolbox presents a review-generated format to harness multiple solutions-based national programs and publications for controlling construction-related risks with simplified approaches across the occupational safety, health and hygiene professions.

Review of Qualitative Approaches for the Construction Industry: Designing a Risk Management Toolbox

PubMed Central

Spee, Ton; Gillen, Matt; Lentz, Thomas J.; Garrod, Andrew; Evans, Paul; Swuste, Paul

2011-01-01

Objectives This paper presents the framework and protocol design for a construction industry risk management toolbox. The construction industry needs a comprehensive, systematic approach to assess and control occupational risks. These risks span several professional health and safety disciplines, emphasized by multiple international occupational research agenda projects including: falls, electrocution, noise, silica, welding fumes, and musculoskeletal disorders. Yet, the International Social Security Association says, "whereas progress has been made in safety and health, the construction industry is still a high risk sector." Methods Small- and medium-sized enterprises (SMEs) employ about 80% of the world's construction workers. In recent years a strategy for qualitative occupational risk management, known as Control Banding (CB) has gained international attention as a simplified approach for reducing work-related risks. CB groups hazards into stratified risk 'bands', identifying commensurate controls to reduce the level of risk and promote worker health and safety. We review these qualitative solutions-based approaches and identify strengths and weaknesses toward designing a simplified CB 'toolbox' approach for use by SMEs in construction trades. Results This toolbox design proposal includes international input on multidisciplinary approaches for performing a qualitative risk assessment determining a risk 'band' for a given project. Risk bands are used to identify the appropriate level of training to oversee construction work, leading to commensurate and appropriate control methods to perform the work safely. Conclusion The Construction Toolbox presents a review-generated format to harness multiple solutions-based national programs and publications for controlling construction-related risks with simplified approaches across the occupational safety, health and hygiene professions. PMID:22953194

50 CFR 91.13 - Technical requirements for design and submission of entry.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 50 Wildlife and Fisheries 9 2014-10-01 2014-10-01 false Technical requirements for design and submission of entry. 91.13 Section 91.13 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR (CONTINUED) MISCELLANEOUS PROVISIONS MIGRATORY BIRD HUNTING AND CONSERVATION STAMP CONTEST Procedures for Entering the...

50 CFR 91.13 - Technical requirements for design and submission of entry.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 50 Wildlife and Fisheries 9 2012-10-01 2012-10-01 false Technical requirements for design and submission of entry. 91.13 Section 91.13 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR (CONTINUED) MISCELLANEOUS PROVISIONS MIGRATORY BIRD HUNTING AND CONSERVATION STAMP CONTEST Procedures for Entering the...

INDOT Construction Inspection Priorities : Technical Summary

DOT National Transportation Integrated Search

2012-05-01

In the last decade, the Indiana Department of Transportation (INDOT) increased the number of construction projects funded by capital made available through the leasing of the Indiana Toll Road. However, during the same time period, the level of perso...

Course of Study Project. Final Report. Vocational-Technical Education Departmental Report, Vol. 17, No. 18.

ERIC Educational Resources Information Center

Pennsylvania State Univ., University Park. Div. of Occupational and Vocational Studies.

Designed for use by area vocational-technical schools and other vocational programs, this project developed courses of study in eight occupational areas: commercial art, appliance repair, automotive mechanics, graphic arts, building trades maintenance, building construction trades, diesel mechanics, and welding. Course-of-study development…

Wave basin model tests of technical-biological bank protection

NASA Astrophysics Data System (ADS)

Eisenmann, J.

2012-04-01

Sloped embankments of inland waterways are usually protected from erosion and other negative im-pacts of ship-induced hydraulic loads by technical revetments consisting of riprap. Concerning the dimensioning of such bank protection there are several design rules available, e.g. the "Principles for the Design of Bank and Bottom Protection for Inland Waterways" or the Code of Practice "Use of Standard Construction Methods for Bank and Bottom Protection on Waterways" issued by the BAW (Federal Waterways Engineering and Research Institute). Since the European Water Framework Directive has been put into action special emphasis was put on natural banks. Therefore the application of technical-biological bank protection is favoured. Currently design principles for technical-biological bank protection on inland waterways are missing. The existing experiences mainly refer to flowing waters with no or low ship-induced hydraulic loads on the banks. Since 2004 the Federal Waterways Engineering and Research Institute has been tracking the re-search and development project "Alternative Technical-Biological Bank Protection on Inland Water-ways" in company with the Federal Institute of Hydrology. The investigation to date includes the ex-amination of waterway sections where technical- biological bank protection is applied locally. For the development of design rules for technical-biological bank protection investigations shall be carried out in a next step, considering the mechanics and resilience of technical-biological bank protection with special attention to ship-induced hydraulic loads. The presentation gives a short introduction into hydraulic loads at inland waterways and their bank protection. More in detail model tests of a willow brush mattress as a technical-biological bank protec-tion in a wave basin are explained. Within the scope of these tests the brush mattresses were ex-posed to wave impacts to determine their resilience towards hydraulic loads. Since the

41 CFR 102-76.15 - What are design and construction services?

Code of Federal Regulations, 2011 CFR

2011-01-01

... 41 Public Contracts and Property Management 3 2011-01-01 2011-01-01 false What are design and construction services? 102-76.15 Section 102-76.15 Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 76-DESIGN AND...

41 CFR 102-76.15 - What are design and construction services?

Code of Federal Regulations, 2014 CFR

2014-01-01

... 41 Public Contracts and Property Management 3 2014-01-01 2014-01-01 false What are design and construction services? 102-76.15 Section 102-76.15 Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 76-DESIGN AND...

41 CFR 102-76.15 - What are design and construction services?

Code of Federal Regulations, 2012 CFR

2012-01-01

... 41 Public Contracts and Property Management 3 2012-01-01 2012-01-01 false What are design and construction services? 102-76.15 Section 102-76.15 Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 76-DESIGN AND...

41 CFR 102-76.15 - What are design and construction services?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 41 Public Contracts and Property Management 3 2013-07-01 2013-07-01 false What are design and construction services? 102-76.15 Section 102-76.15 Public Contracts and Property Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 76-DESIGN AND...

Lessons Learned and Technical Standards: A Logical Marriage for Future Space Systems Design

NASA Technical Reports Server (NTRS)

Gill, Paul S.; Garcia, Danny; Vaughan, William W.; Parker, Nelson C. (Technical Monitor)

2002-01-01

A comprehensive database of engineering lessons learned that corresponds with relevant technical standards will be a valuable asset to those engaged in studies on future space vehicle developments, especially for structures, materials, propulsion, control, operations and associated elements. In addition, this will enable the capturing of technology developments applicable to the design, development, and operation of future space vehicles as planned in the Space Launch Initiative. Using the time-honored tradition of passing on lessons learned while utilizing the newest information technology, NASA has launched an intensive effort to link lessons learned acquired through various Internet databases with applicable technical standards. This paper will discuss the importance of lessons learned, the difficulty in finding relevant lessons learned while engaged in a space vehicle development, and the new NASA effort to relate them to technical standards that can help alleviate this difficulty.

Conceptual Design of a Space-Based Multimegawatt MHD Power System, Task 1 Topical Report; Volume 1: Technical Discussion

DTIC Science & Technology

1988-01-01

system requirements, design guidelines, and interface requirements has been prepared and included as Volume II of this Task 1 topical report. The Volume ...WAESD-TR-88-0002 Conceptual Design Of A Space-Based Multimegawatt MHD Power System ffA«kjjjjjTfc Task 1 Topical Report Volume I: Technical...Space-Based Multimegawatt MHD Power System: Task 1 Topical Report, Volume I: Technical Discussion Personal Author: Dana, RA. Corporate Author Or

Considerations in computer-aided design for inlay cranioplasty: technical note.

PubMed

Nout, Erik; Mommaerts, Maurice Y

2018-03-01

Cranioplasty is a frequently performed procedure that uses a variety of reconstruction materials and techniques. In this technical note, we present refinements of computer-aided design-computer-aided manufacturing inlay cranioplasty. In an attempt to decrease complications related to polyether-ether-ketone (PEEK) cranioplasty, we gradually made changes to implant design and cranioplasty techniques. These changes include under-contouring of the implant and the use of segmented plates for large defects, microplate fixation for small temporal defects, temporal shell implants to reconstruct the temporalis muscle, and perforations to facilitate the drainage of blood and cerebrospinal fluid and serve as fixation points. From June 2016 to June 2017, 18 patients underwent cranioplasty, and a total of 31 PEEK and titanium implants were inserted. All implants were successful. These changes to implant design and cranioplasty techniques facilitate the insertion and fixation of patient-specific cranial implants and improve esthetic outcomes.

Construction, Part of Indoor Air Quality Design Tools for Schools

EPA Pesticide Factsheets

Poor job-site construction practices can frustrate even the best design by allowing moisture and other contaminants to become potential long term problems. Preventive job-site practices will reduce the potential for residual problems with IAQ

Visual Design Principles Applied To World Wide Web Construction.

ERIC Educational Resources Information Center

Luck, Donald D.; Hunter, J. Mark

This paper describes basic types of World Wide Web pages and presents design criteria for page layout based on principles of visual literacy. Discussion focuses on pages that present information in the following styles: billboard; directory/index; textual; and graphics. Problems and solutions in Web page construction are explored according to…

47 CFR 25.113 - Station construction, launch authority, and operation of spare satellites.

Code of Federal Regulations, 2014 CFR

2014-10-01

... this part, and technical design requirements. Prior to commencing such construction and pre-operational... specify the frequencies the licensee proposes to use for pre-operational testing and the name, address... resulting from such testing. MSS/ATC licensees engaging in pre-operational testing must comply with §§ 5.83...

Design, Construction, and Test of a 473 MHZ Four - Cavity Rfq.

NASA Astrophysics Data System (ADS)

Kazimi, Reza

1992-01-01

An RFQ accelerator using the new four-rod cavity design has been fabricated and successfully tested at Texas Accelerator Center. The RFQ is designed to accelerate a 10 mA H^- ion beam from 30 keV to 500 keV with the operating frequency of 473 MHz. This new type of RFQ structure not only promises simplicity of design, construction, and operation, but also can be manufactured to operate at higher frequencies than previously achieved by other four-rod type RFQs. Combination of simplicity and compactness due to higher operating frequencies (400 to 500 MHz) makes the design desirable for injector of proton accelerators, medical linear accelerators, and variety of other applications. This dissertation presents the steps I went through in inventing, developing, and experimentally testing this new RFQ design. First an introduction to accelerators is given, and the basic accelerator physics terminologies are defined. The principles of operations of the RFQs are described, and the theory behind new type of RFQ structure is explained. Then the beam dynamics and cavity design of the RFQ are presented. Finally, the mechanical design and construction procedure are discussed, and experimental results of rf tests and actual H ^- beam test are given.

Lessons Learned from the 200 West Pump and Treatment Facility Construction Project at the US DOE Hanford Site - A Leadership for Energy and Environmental Design (LEED) Gold-Certified Facility - 13113

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dorr, Kent A.; Freeman-Pollard, Jhivaun R.; Ostrom, Michael J.

CH2M Hill Plateau Remediation Company (CHPRC) designed, constructed, commissioned, and began operation of the largest groundwater pump and treatment facility in the U.S. Department of Energy's (DOE) nationwide complex. This one-of-a-kind groundwater pump and treatment facility, located at the Hanford Nuclear Reservation Site (Hanford Site) in Washington State, was built to an accelerated schedule with American Recovery and Reinvestment Act (ARRA) funds. There were many contractual, technical, configuration management, quality, safety, and Leadership in Energy and Environmental Design (LEED) challenges associated with the design, procurement, construction, and commissioning of this $95 million, 52,000 ft groundwater pump and treatment facility tomore » meet DOE's mission objective of treating contaminated groundwater at the Hanford Site with a new facility by June 28, 2012. The project team's successful integration of the project's core values and green energy technology throughout design, procurement, construction, and start-up of this complex, first-of-its-kind Bio Process facility resulted in successful achievement of DOE's mission objective, as well as attainment of LEED GOLD certification (Figure 1), which makes this Bio Process facility the first non-administrative building in the DOE Office of Environmental Management complex to earn such an award. (authors)« less

Design-Construct Method Saves Time and Money in New School Building

ERIC Educational Resources Information Center

Modern Schools, 1972

1972-01-01

Describes the Lottie M. Schmidt Elementary School in New Baltimore, Michigan, completed in 154 days. Designed to a price rather than priced to a design, the school was built at considerable savings over modular approaches -- and the modest price also covered furniture, electric heating/cooling, carpeting, full masonry construction, concrete slab…

Design space construction of multiple dose-strength tablets utilizing bayesian estimation based on one set of design-of-experiments.

PubMed

Maeda, Jin; Suzuki, Tatsuya; Takayama, Kozo

2012-01-01

Design spaces for multiple dose strengths of tablets were constructed using a Bayesian estimation method with one set of design of experiments (DoE) of only the highest dose-strength tablet. The lubricant blending process for theophylline tablets with dose strengths of 100, 50, and 25 mg is used as a model manufacturing process in order to construct design spaces. The DoE was conducted using various Froude numbers (X(1)) and blending times (X(2)) for theophylline 100-mg tablet. The response surfaces, design space, and their reliability of the compression rate of the powder mixture (Y(1)), tablet hardness (Y(2)), and dissolution rate (Y(3)) of the 100-mg tablet were calculated using multivariate spline interpolation, a bootstrap resampling technique, and self-organizing map clustering. Three experiments under an optimal condition and two experiments under other conditions were performed using 50- and 25-mg tablets, respectively. The response surfaces of the highest-strength tablet were corrected to those of the lower-strength tablets by Bayesian estimation using the manufacturing data of the lower-strength tablets. Experiments under three additional sets of conditions of lower-strength tablets showed that the corrected design space made it possible to predict the quality of lower-strength tablets more precisely than the design space of the highest-strength tablet. This approach is useful for constructing design spaces of tablets with multiple strengths.

Designing I*CATch: A Multipurpose, Education-Friendly Construction Kit for Physical and Wearable Computing

ERIC Educational Resources Information Center

Ngai, Grace; Chan, Stephen C. F.; Leong, Hong Va; Ng, Vincent T. Y.

2013-01-01

This article presents the design and development of i*CATch, a construction kit for physical and wearable computing that was designed to be scalable, plug-and-play, and to provide support for iterative and exploratory learning. It consists of a standardized construction interface that can be adapted for a wide range of soft textiles or electronic…

STEM integration in middle school career and technical education programs: A Delphi design study

NASA Astrophysics Data System (ADS)

Wu-Rorrer, Billy Ray

The purpose of this qualitative method study with a Delphi research design sought to determine how STEM programs can be effectively integrated into middle school career and technical education programs by local, state, and national educators, administrators, directors, specialists, and curriculum writers. The significance of the study is to provide leaders in CTE with a greater awareness, insight, and strategies about how CTE programs can more effectively integrate academics into career and technical education programs through STEM-related programming. The findings will increase the limited amount of available literature providing best practice strategies for the integration of STEM curriculum into middle school CTE programs. One basic question has guided this research: How can STEM programs be effectively integrated into middle school career and technical education programs? A total of twelve strategies were identified. The strategies of real-world applications and administrative buy-in were the two predominant strategies consistently addressed throughout the review of literature and all three sub-questions in the research study. The Delphi design study consisted of pilot round and three rounds of data collection on barriers, strategies, and professional development for STEM integration in middle school career and technical education programs. Four panelists participated in the pilot round, and 16 panel members not involved in the pilot round participated in the three rounds of questioning and consensus building. In the future, more comprehensive studies can build upon this foundational investigation of middle school CTE programs.

A Theoretical Construct of Serious Play and the Design of a Tangible Social Interface

NASA Astrophysics Data System (ADS)

Jennings, Pamela L.

To construct is to creatively invent one's world by engaging in creative decision-making, problem solving, and negotiation. The metaphor of construction is used to demonstrate how a simple artifact - a building blockw can be used to facilitate the exploration of personal narratives. This chapter presents an argument for the development of tangible social interfaces and interaction design practices that are informed by the premises of twentieth century philosophical and cultural theories. Specifically, this chapter explores the historical notion of the role of play in constructing a civic society. The constructed narratives' electronic construction kit is introduced as an example of research and development of a critical creative technology built on a wireless ad hoc 802.15.4 network platform. The game is designed to support collaborative play and learning.

Flood type specific construction of synthetic design hydrographs

NASA Astrophysics Data System (ADS)

Brunner, Manuela I.; Viviroli, Daniel; Sikorska, Anna E.; Vannier, Olivier; Favre, Anne-Catherine; Seibert, Jan

2017-02-01

Accurate estimates of flood peaks, corresponding volumes, and hydrographs are required to design safe and cost-effective hydraulic structures. In this paper, we propose a statistical approach for the estimation of the design variables peak and volume by constructing synthetic design hydrographs for different flood types such as flash-floods, short-rain floods, long-rain floods, and rain-on-snow floods. Our approach relies on the fitting of probability density functions to observed flood hydrographs of a certain flood type and accounts for the dependence between peak discharge and flood volume. It makes use of the statistical information contained in the data and retains the process information of the flood type. The method was tested based on data from 39 mesoscale catchments in Switzerland and provides catchment specific and flood type specific synthetic design hydrographs for all of these catchments. We demonstrate that flood type specific synthetic design hydrographs are meaningful in flood-risk management when combined with knowledge on the seasonality and the frequency of different flood types.

Implementation of straight and curved steel girder erection design tools construction : summary.

DOT National Transportation Integrated Search

2010-11-05

Project 0-5574 Curved Plate Girder Design for Safe and Economical Construction, resulted in the : development of two design tools, UT Lift and UT Bridge. UT Lift is a spreadsheet-based program for analyzing : steel girders during lifting while ...

Design of lane merges at rural freeway construction work zones.

DOT National Transportation Integrated Search

2008-02-01

The goal of this project is to evaluate unconventional lane-drop merge configurations in the vicinity of construction work zones on rural freeways to comparatively assess the conditions of the various designs that impact delay, flow, and safety throu...

Unresolved Technical Issues in Fair Interest Measurement.

ERIC Educational Resources Information Center

Cole, Nancy S.

The problem of sex differences in interest measurement involves many technical issues and procedures. The purpose of this paper is to provide a description of the technical problems involved in construction, scoring, and interpretation of interest measures as related to sex differences and to suggest guidelines within these technical issues which…

Normative and economic foundations of high-rise construction in the city of Samara

NASA Astrophysics Data System (ADS)

Didkovskaya, Olga V.; Bocharov, Aleksey Y.; Ilyina, Marina V.; Mamaeva, Olga A.

2018-03-01

Every year the number of free land plots for construction of buildings is steadily decreasing in cities. In this regard, the participants in the investment and construction process are increasingly seeking to maximize the use of land. A logical way for this is to use high-rise construction. However, until recently, builders encountered serious obstacles in the form of lack of special norms and rules for the design of high-rise buildings. It led to the need for individual coordination of each high-rise facility, the development and approval of special technical conditions, the passage of numerous administrative approvals. Thus, investment activity regarding the construction of high-rise buildings in the Russian Federation is reduced. In 2016, there were regulatory changes that substantially alleviated these difficulties. In this article, the authors analyze the features of the town-planning normative-legal field of high-rise construction and its development, track the interrelations between the regulatory regulation of the construction of similar facilities, with the real need, the technical feasibility and economic feasibility of their construction in the urban district of Samara. Conclusions and suggestions are also based on the analysis of the norms of urban zoning, the residential real estate market and the value of land plots.

Design and construction of a remote piloted flying wing. B.S. Thesis

NASA Technical Reports Server (NTRS)

Costa, Alfred J.; Koopman, Fritz; Soboleski, Craig; Trieu, Thai-Ba; Duquette, Jaime; Krause, Scott; Susko, David; Trieu, Thuyba

1994-01-01

Currently, there is a need for a high-speed, high-lift civilian transport. Although unconventional, a flying wing could fly at speeds in excess of Mach 2 and still retain the capacity of a 747. The design of the flying wing is inherently unstable since it lacks a fuselage and a horizontal tail. The project goal was to design, construct, fly, and test a remote-piloted scale model flying wing. The project was completed as part of the NASA/USRA Advanced Aeronautics Design Program. These unique restrictions required us to implement several fundamental design changes from last year's Elang configuration including wing sweepback and wingtip endplates. Unique features such as a single ducted fan engine, composite structural materials, and an electrostatic stability system were incorporated. The result is the Banshee '94. Our efforts will aid future projects in design and construction techniques so that a viable flying wing can become an integral part of the aviation industry.

Experience in design and construction of the Log tunnel

NASA Astrophysics Data System (ADS)

Jovičić, Vojkan; Goleš, Niko; Tori, Matija; Peternel, Miha; Vajović, Stanojle; Muhić, Elvir

2017-09-01

A twin highway Log tunnel is a part of a new motorway connection between Maribor and Zagreb, section Draženci-Gru\\vskovje, which is located towards the border crossing between Slovenia and Croatia. The tunnel is currently under construction, and only the excavation works have been completed during the writing of this paper. The terrain in the area of the Log tunnel is diverse, and the route of the highway in its vicinity is characterised by deep excavations, bridges or viaducts. The Log tunnel is approximately 250 m long, partly constructed as a gallery. The geological conditions are dominated by Miocene base rock, featuring layers of well-connected clastic rocks, which are covered by diluvium clays, silts, sands and gravels of different thicknesses. Due to the short length of the tunnel, the usual separation of the motorway route to the left and the right tunnel axes was not carried out. Thus, the tunnel was constructed with an intermediate pillar and was designed as a three-lane tunnel, including the stopping lane. The construction of the tunnel was carried out using the New Austrian tunnelling method (NATM), in which the central adit was excavated first and the intermediate pillar was constructed within it. The excavation of the main tubes followed and was divided into the top heading, bench and the invert, enabling the intermediate pillar to take the load off the top heading of both tubes. The secondary lining of the tunnel is currently under construction. The experience of the tunnel construction gathered so far is presented in the paper. The main emphasis is on the construction of the intermediate pillar, which had to take the significant and asymmetrical ground load.

Engineering and Technical Efforts to Design and Construct a 10 MW gyrotron Laboratory

DTIC Science & Technology

1989-01-18

coupling coefficients are proptional to the square of the effective electric field at the beam. The effective electric field, Es, is given in...develop- ed to alleviate shorts in the body current beam diagnostic and baking constraints that previous o-ring designs have experienced. The prototype

Best practices of Building Information Modelling (BIM) implementation in design phase for construction project

NASA Astrophysics Data System (ADS)

Kasim, N.; Zainal Abidin, N. A.; Zainal, R.; Sarpin, N.; Rahim, M. H. I. Abd; Saikah, M.

2017-11-01

Implementation of Building Information Modelling (BIM) was expected to bring improvement in current practices of Malaysian construction industry. In the design phase, there is a lack of a ready pool of skilled workers who are able to develop BIM strategic plan and effectively utilise it. These create boundaries for BIM nature in Malaysian construction industry specifically in the design phase to achieve its best practices. Therefore, the objectives of this research are to investigate the current practices of BIM implementation in the design phase as well as the best practices factors of BIM implementation in the design phase. The qualitative research approach is carried out through semi-structured interviews with the designers of different organisations which adopt BIM in the design phase. Data collection is analysed by executing content analysis method. From the findings, the best practices factors of BIM implementation in design phase such as the incentive for BIM training, formal approach to monitoring automated Level of Detailing (LOD), run a virtual meeting and improve Industry Foundation Class (IFC). Thus, best practices factors which lead to practices improvements in the design phase of project development which subsequently improves the implementation of BIM in the design phase of Malaysian construction industry.

Design and construction of the X-2 two-stage free piston driven expansion tube

NASA Technical Reports Server (NTRS)

Doolan, Con

1995-01-01

This report outlines the design and construction of the X-2 two-stage free piston driven expansion tube. The project has completed its construction phase and the facility has been installed in the new impulsive research laboratory where commissioning is about to take place. The X-2 uses a unique, two-stage driver design which allows a more compact and lower overall cost free piston compressor. The new facility has been constructed in order to examine the performance envelope of the two-stage driver and how well it couple to sub-orbital and super-orbital expansion tubes. Data obtained from these experiments will be used for the design of a much larger facility, X-3, utilizing the same free piston driver concept.

Strategic advantages of high-rise construction

NASA Astrophysics Data System (ADS)

Yaskova, Natalya

2018-03-01

Traditional methods to assess the competitiveness of different types of real estate in the context of huge changes of new technological way of life don't provide building solutions that would be correct from a strategic perspective. There are many challenges due to changes in the consumers' behavior in the housing area. A multiplicity of life models, a variety of opportunities and priorities, traditions and new trends in construction should be assessed in terms of prospective benefits in the environment of the emerging new world order. At the same time, the mane discourse of high-rise construction mainly relates to its design features, technical innovations, and architectural accents. We need to clarify the criteria for economic evaluation of high-rise construction in order to provide decisions with clear and quantifiable contexts. The suggested approach to assessing the strategic advantage of high-rise construction and the prospects for capitalization of high-rise buildings poses new challenges for the economy to identify adequate quantitative assessment methods of the high-rise buildings economic efficiency, taking into account all stages of their life cycle.

Capital Construction Budget Recommendations and Prioritization, 2011-2013 Biennium: For the Nebraska State College System, University of Nebraska and Nebraska College of Technical Agriculture

ERIC Educational Resources Information Center

Nebraska's Coordinating Commission for Postsecondary Education, 2010

2010-01-01

The Coordinating Commission for Postsecondary Education provides funding and priority recommendations for the Nebraska State College's, the University of Nebraska's and the Nebraska College of Technical Agriculture at Curtis' capital construction requests, as outlined in Nebraska's Constitution and Statutes. The overarching principle used in this…

Review Of Piping And Pressure Vessel Code Design Criteria. Technical Report 217.

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

1969-04-18

This Technical Report summarizes a review of the design philosophies and criteria of the ASME Boiler and Pressure Vessel Code and the USASI Code for Pressure Piping. It traces the history of the Codes since their inception and critically reviews their present status. Recommendations are made concerning the applicability of the Codes to the special needs of LMFBR liquid sodium piping.

Design and Construction of Manned Lunar Base

NASA Astrophysics Data System (ADS)

Li, Zhijie

2016-07-01

Building manned lunar base is one of the core aims of human lunar exploration project, which is also an important way to carry out the exploitation and utilization of lunar in situ resources. The most important part of manned lunar base is the design and construction of living habitation and many factors should be considered including science objective and site selection. Through investigating and research, the scientific goals of manned lunar base should be status and characteristics ascertainment of lunar available in situ resources, then developing necessary scientific experiments and utilization of lunar in situ resources by using special environment conditions of lunar surface. The site selection strategy of manned lunar base should rely on scientific goals according to special lunar surface environment and engineering capacity constraints, meanwhile, consulting the landing sites of foreign unmanned and manned lunar exploration, and choosing different typical regions of lunar surface and analyzing the landform and physiognomy, reachability, thermal environment, sunlight condition, micro meteoroids protection and utilization of in situ resources, after these steps, a logical lunar living habitation site should be confirmed. This paper brings out and compares three kinds of configurations with fabricating processes of manned lunar base, including rigid module, flexible and construction module manned lunar base. 1.The rigid habitation module is usually made by metal materials. The design and fabrication may consult the experience of space station, hence with mature technique. Because this configuration cannot be folded or deployed, which not only afford limit working and living room for astronauts, but also needs repetitious cargo transit between earth and moon for lunar base extending. 2. The flexible module habitation can be folded in fairing while launching. When deploying on moon, the configuration can be inflatable or mechanically-deployed, which means under

Advancing Integrated STEM Learning through Engineering Design: Sixth-Grade Students' Design and Construction of Earthquake Resistant Buildings

ERIC Educational Resources Information Center

English, Lyn D.; King, Donna; Smeed, Joanna

2017-01-01

As part of a 3-year longitudinal study, 136 sixth-grade students completed an engineering-based problem on earthquakes involving integrated STEM learning. Students employed engineering design processes and STEM disciplinary knowledge to plan, sketch, then construct a building designed to withstand earthquake damage, taking into account a number of…

Helping Students to Prepare a Technical Communications Portfolio.

ERIC Educational Resources Information Center

Ware, Elaine

1988-01-01

Stresses the importance of teaching prospective technical writers to develop, organize, and present a technical communications portfolio. Provides a checklist on portfolio construction for students. (ARH)

The Development, Design and Construction of Gliders and Sailplanes

NASA Technical Reports Server (NTRS)

Lippisch, A

1931-01-01

This report explains and details the history of glider design and construction through the impetus of the Rhon Sailplane contests. Some of the topics considered include: whether the longitudinal stability (dynamic and static) is sufficient in the tailless typo and a consideration that the structural weight of sweptback wings would be greater than that of a corresponding normal wing.

NREL and iUnit: Leading the Design for Net Zero Multifamily Construction |

Science.gov Websites

Capabilities for iUnit NREL and iUnit: Leading the Design for Net Zero Multifamily Construction NREL is research capabilities and energy modeling tools to lead the design, demonstration, and integration of net housing, such as iUNIT's integrated design that incorporates a tenant feedback platform, could save $3.4

Proceedings of the Technical Workshops For the Hydraulic Fracturing Study: Well Construction and Operation, U.S. Environmental Protection Agency EPA 600/R-11/046, May 2011

EPA Pesticide Factsheets

These proceedings provide an overview of the twenty-four presentations given on well construction and operations at the Technical Workshop for the U.S. EPA Hydraulic Fracturing Study held on March 10–11, 2011.

Brownfields Waterfront Sustainability Pilot, Allentown PA: Technical Memorandum on Conceptual Design Using Low Impact Development

EPA Pesticide Factsheets

This technical memorandum briefly describes the site and the master plan, indicates design constraints considered, specifies recommended LID stormwater techniques and features for sustainable redevelopment of the site, and offers other recommendations.

Challenges and opportunities in the design and construction of a GIS-based emission inventory infrastructure for the Niger Delta region of Nigeria.

PubMed

Fagbeja, Mofoluso A; Hill, Jennifer L; Chatterton, Tim J; Longhurst, James W S; Akpokodje, Joseph E; Agbaje, Ganiy I; Halilu, Shaba A

2017-03-01

Environmental monitoring in middle- and low-income countries is hampered by many factors which include enactment and enforcement of legislations; deficiencies in environmental data reporting and documentation; inconsistent, incomplete and unverifiable data; a lack of access to data; and technical expertise. This paper describes the processes undertaken and the major challenges encountered in the construction of the first Niger Delta Emission Inventory (NDEI) for criteria air pollutants and CO 2 released from the anthropogenic activities in the region. This study focused on using publicly available government and research data. The NDEI has been designed to provide a Geographic Information System-based component of an air quality and carbon management framework. The NDEI infrastructure was designed and constructed at 1-, 10- and 20-km grid resolutions for point, line and area sources using industry standard processes and emission factors derived from activities similar to those in the Niger Delta. Due to inadequate, incomplete, potentially inaccurate and unavailable data, the infrastructure was populated with data based on a series of best possible assumptions for key emission sources. This produces outputs with variable levels of certainty, which also highlights the critical challenges in the estimation of emissions from a developing country. However, the infrastructure is functional and has the ability to produce spatially resolved emission estimates.

Design with constructal theory: Steam generators, turbines and heat exchangers

NASA Astrophysics Data System (ADS)

Kim, Yong Sung

This dissertation shows that the architecture of steam generators, steam turbines and heat exchangers for power plants can be predicted on the basis of the constructal law. According to constructal theory, the flow architecture emerges such that it provides progressively greater access to its currents. Each chapter shows how constructal theory guides the generation of designs in pursuit of higher performance. Chapter two shows the tube diameters, the number of riser tubes, the water circulation rate and the rate of steam production are determined by maximizing the heat transfer rate from hot gases to riser tubes and minimizing the global flow resistance under the fixed volume constraint. Chapter three shows how the optimal spacing between adjacent tubes, the number of tubes for the downcomer and the riser and the location of the flow reversal for the continuous steam generator are determined by the intersection of asymptotes method, and by minimizing the flow resistance under the fixed volume constraints. Chapter four shows that the mass inventory for steam turbines can be distributed between high pressure and low pressure turbines such that the global performance of the power plant is maximal under the total mass constraint. Chapter five presents the more general configuration of a two-stream heat exchanger with forced convection of the hot side and natural circulation on the cold side. Chapter six demonstrates that segmenting a tube with condensation on the outer surface leads to a smaller thermal resistance, and generates design criteria for the performance of multi-tube designs.

Progress in Design and Construction of the Optical Communications Laser Laboratory

NASA Technical Reports Server (NTRS)

Wilson, K. E.; Britcliffe, M.; Golshan, N.

1999-01-01

The deployment of advanced hyperspectral imaging and other Earth sensing instruments on board Earth observing satellites is driving the demand for high-data-rate communications. Optical communications meet the required data rates with small, low mass, and low-power communications packages. JPL, as NASA's lead center in optical communications, plans to construct a 1-m Optical Communications Telescope Laboratory (OCTL) at its Table Mountain Facility (TMF) complex in the San Gabriel Mountains of Southern California. The design of the building has been completed, and the construction contractor has been selected. Ground breaking is expected to start at the beginning of the 1999 TMF construction season. A request for proposal (RFP) has been issued for the procurement of the telescope system. Prior to letting the RFP we conducted a request for information with industry for the telescope system. Several vendors responded favorably and provided information on key elements of the proposed design. These inputs were considered in developing the final requirements in the RFP. Keywords: Free space optical communications, lasercom, telescopes, ground stations, adaptive optics, astrometry, Table Mountain Facility

SCHOOLS OF PRESTRESSED CONCRETE. PLANNING, DESIGN AND CONSTRUCTION OF EDUCATIONAL FACILITIES FOR SCHOOLS AND COLLEGES.

ERIC Educational Resources Information Center

LYMAN, ROBERT J.

THE USE OF PRESTRESSED CONCRETE IS EMPHASIZED IN THE AREAS OF SCHOOL PLANNING, DESIGN, AND CONSTRUCTION. THE PLANNING SECTION INCLUDES--(1) ROLES OF ACTIVE PARTIES AND RELATED ORGANIZATIONS, (2) PROCEDURES, AND (3) CONCEPTUAL DATA FOR SITE AND BUILDING. THE DESIGN SECTION CONTAINS--(1) DEVELOPMENT OF CONSTRUCTION SYSTEMS, (2) INTEGRATION OF…

10 CFR Appendix N to Part 52 - Standardization of Nuclear Power Plant Designs: Combined Licenses To Construct and Operate...

Code of Federal Regulations, 2011 CFR

2011-01-01

... Licenses To Construct and Operate Nuclear Power Reactors of Identical Design at Multiple Sites N Appendix N... Designs: Combined Licenses To Construct and Operate Nuclear Power Reactors of Identical Design at Multiple... construct and operate nuclear power reactors of identical design (“common design”) to be located at multiple...

The quality estimation of exterior wall’s and window filling’s construction design

NASA Astrophysics Data System (ADS)

Saltykov, Ivan; Bovsunovskaya, Maria

2017-10-01

The article reveals the term of “artificial envelope” in dwelling building. Authors offer a complex multifactorial approach to the design quality estimation of external fencing structures, which is based on various parameters impact. These referred parameters are: functional, exploitation, cost, and also, the environmental index is among them. The quality design index Qк is inputting for the complex characteristic of observed above parameters. The mathematical relation of this index from these parameters is the target function for the quality design estimation. For instance, the article shows the search of optimal variant for wall and window designs in small, middle and large square dwelling premises of economic class buildings. The graphs of target function single parameters are expressed for the three types of residual chamber’s dimensions. As a result of the showing example, there is a choice of window opening’s dimensions, which make the wall’s and window’s constructions properly correspondent to the producible complex requirements. The authors reveal the comparison of recommended window filling’s square in accordance with the building standards, and the square, due to the finding of the optimal variant of the design quality index. The multifactorial approach for optimal design searching, which is mentioned in this article, can be used in consideration of various construction elements of dwelling buildings in accounting of suitable climate, social and economic construction area features.

Innovative Approaches to Teaching Technical Communication

ERIC Educational Resources Information Center

Bridgeford, Tracy, Ed.; Kitalong, Karla Saari, Ed.; Selfe, Dickie, Ed.

2004-01-01

"Innovative Approaches to Teaching Technical Communication" offers a variety of activities, projects, and approaches to energize pedagogy in technical communication and to provide a constructive critique of current practice. A practical collection, the approaches recommended here are readily adaptable to a range of technological and institutional…

Protection of Workers and Third Parties during the Construction of Linear Structures

NASA Astrophysics Data System (ADS)

Vlčková, Jitka; Venkrbec, Václav; Henková, Svatava; Chromý, Adam

2017-12-01

The minimization of risk in the workplace through a focus on occupational health and safety (OHS) is one of the primary objectives for every construction project. The most serious accidents in the construction industry occur during work on earthworks and linear structures. The character of such structures places them among those posing the greatest threat to the public (referred to as “third parties”). They can be characterized as large structures whose construction may involve the building site extending in a narrow lane alongside previously constructed objects currently in use by the public. Linear structures are often directly connected to existing objects or buildings, making it impossible to guard the whole construction site. However, many OHS problems related to linear structures can be prevented during the design stage. The aim of this article is to introduce a new methodology which has been implemented into a computer program that deals with safety measures at construction sites where work is performed on linear structures. Based on existing experience with the design of such structures and their execution and supervision by safety coordinators, the basic types of linear structures, their location in the terrain, the conditions present during their execution and other marginal conditions and influences were modelled. Basic safety information has been assigned to this elementary information, which is strictly necessary for the construction process. The safety provisions can be grouped according to type, e.g. technical, organizational and other necessary documentation, or into sets of provisions concerning areas such as construction site safety, transport safety, earthworks safety, etc. The selection of the given provisions takes place using multiple criteria. The aim of creating this program is to provide a practical tool for designers, contractors and construction companies. The model can contribute to the sufficient awareness of these participants

Computational model-informed design and bioprinting of cell-patterned constructs for bone tissue engineering.

PubMed

Carlier, Aurélie; Skvortsov, Gözde Akdeniz; Hafezi, Forough; Ferraris, Eleonora; Patterson, Jennifer; Koç, Bahattin; Van Oosterwyck, Hans

2016-05-17

Three-dimensional (3D) bioprinting is a rapidly advancing tissue engineering technology that holds great promise for the regeneration of several tissues, including bone. However, to generate a successful 3D bone tissue engineering construct, additional complexities should be taken into account such as nutrient and oxygen delivery, which is often insufficient after implantation in large bone defects. We propose that a well-designed tissue engineering construct, that is, an implant with a specific spatial pattern of cells in a matrix, will improve the healing outcome. By using a computational model of bone regeneration we show that particular cell patterns in tissue engineering constructs are able to enhance bone regeneration compared to uniform ones. We successfully bioprinted one of the most promising cell-gradient patterns by using cell-laden hydrogels with varying cell densities and observed a high cell viability for three days following the bioprinting process. In summary, we present a novel strategy for the biofabrication of bone tissue engineering constructs by designing cell-gradient patterns based on a computational model of bone regeneration, and successfully bioprinting the chosen design. This integrated approach may increase the success rate of implanted tissue engineering constructs for critical size bone defects and also can find a wider application in the biofabrication of other types of tissue engineering constructs.

Knowledge Construction and Knowledge Representation in High School Students' Design of Hypermedia Documents

ERIC Educational Resources Information Center

Chen, Pearl; McGrath, Diane

2003-01-01

This study documented the processes of knowledge construction and knowledge representation in high school students' hypermedia design projects. Analysis of knowledge construction in linking and structural building yielded distinct types and subtypes of hypermedia documents, which were characterized by four features of knowledge representation: (a)…

41 CFR 102-76.10 - What basic design and construction policy governs Federal agencies?

Code of Federal Regulations, 2012 CFR

2012-01-01

... basic design and construction policies: (a) Provide the highest quality services for designing and... requirements. (See 40 U.S.C. 3310 and 3312.) (d) Design Federal buildings to have a long life expectancy and...

41 CFR 102-76.10 - What basic design and construction policy governs Federal agencies?

Code of Federal Regulations, 2013 CFR

2013-07-01

... basic design and construction policies: (a) Provide the highest quality services for designing and... requirements. (See 40 U.S.C. 3310 and 3312.) (d) Design Federal buildings to have a long life expectancy and...

Career and Self-Construction of Emerging Adults: The Value of Life Designing

PubMed Central

Maree, Jacobus G.; Twigge, Adeline

2016-01-01

This article describes a potential way of counseling emerging adults from a life design perspective to construct a self that could enable them to be agents of both their own development and the development of others. Theoretical issues relating to a dynamic, developmental and systems framework of the understanding of wellbeing are described and the process involved is delineated. The research design was qualitative and comprised case studies. Six participants who subscribed to the definition of “emerging adults” and were comparatively representative of the ethnic diversity of South Africa, were selected purposively from a group of individuals who applied for career counseling in a private practice context. The intervention involved life design counseling and occurred over a period of 6 weeks. Information related to participants' self-construction was gathered using qualitative techniques, including the Career Interest Profile, the Career Construction Interview, a timeline, video clips, a collage, and semi-structured interviews. Following the intervention, the participants revealed heightened insights with regard to aspects of their sense of a relational-moral self. Results indicated that life design counseling could enhance elaborative personal development (enhancing self-awareness and reaping the benefits of developing an improved relational-moral self) and the promotion of an awareness of the importance to promote social justice in work-related contexts. PMID:26793152

Event-based design tool for construction site erosion and sediment controls

NASA Astrophysics Data System (ADS)

Trenouth, William R.; Gharabaghi, Bahram

2015-09-01

This paper provides additional discussion surrounding the novel event-based soil loss models developed by Trenouth and Gharabaghi (2015) for the design of erosion and sediment controls (ESCs) for various phases of construction - from pre-development to post-development conditions. The datasets for the study were obtained from three Ontario sites - Greensborough, Cookstown, and Alcona - in addition to datasets mined from the literature for three additional sites - Treynor, Iowa, Coshocton, Ohio and Cordoba, Spain. Model performances were evaluated for each of the study sites, and quantified using commonly-reported statistics. This work is nested within a broader conceptual framework, which includes the estimation of ambient receiving water quality, the prediction of event mean runoff quality for a given design storm, and the calculation of the required level of protection using adequate ESCs to meet receiving water quality guidelines. These models allow design engineers and regulatory agencies to assess the potential risk of ecological damage to receiving waters due to inadequate soil erosion and sediment control practices using dynamic scenario forecasting when considering rapidly changing land use conditions during various phases of construction, typically for a 2- or 5-year design storm return period.

Organizational Learning and Product Design Management: Towards a Theoretical Model.

ERIC Educational Resources Information Center

Chiva-Gomez, Ricardo; Camison-Zornoza, Cesar; Lapiedra-Alcami, Rafael

2003-01-01

Case studies of four Spanish ceramics companies were used to construct a theoretical model of 14 factors essential to organizational learning. One set of factors is related to the conceptual-analytical phase of the product design process and the other to the creative-technical phase. All factors contributed to efficient product design management…

36 CFR 223.38 - Standards for road design and construction.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 36 Parks, Forests, and Public Property 2 2012-07-01 2012-07-01 false Standards for road design and construction. 223.38 Section 223.38 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE SALE AND DISPOSAL OF NATIONAL FOREST SYSTEM TIMBER, SPECIAL FOREST PRODUCTS, AND FOREST BOTANICAL...

36 CFR 223.38 - Standards for road design and construction.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 36 Parks, Forests, and Public Property 2 2013-07-01 2013-07-01 false Standards for road design and construction. 223.38 Section 223.38 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE SALE AND DISPOSAL OF NATIONAL FOREST SYSTEM TIMBER, SPECIAL FOREST PRODUCTS, AND FOREST BOTANICAL...

Teacher Collaborative Curriculum Design in Technical Vocational Colleges: A Strategy for Maintaining Curriculum Consistency?

ERIC Educational Resources Information Center

Albashiry, Nabeel M.; Voogt, Joke M.; Pieters, Jules M.

2015-01-01

The Technical Vocational Education and Training (TVET) curriculum requires continuous renewal and constant involvement of stakeholders in the redesign process. Due to a lack of curriculum design expertise, TVET institutions in developing contexts encounter challenges maintaining and advancing the quality and relevance of their programmes to the…

Design and construction of a multiwavelength, micromirror total internal reflectance fluorescence microscope.

PubMed

Larson, Joshua; Kirk, Matt; Drier, Eric A; O'Brien, William; MacKay, James F; Friedman, Larry J; Hoskins, Aaron A

2014-10-01

Colocalization single-molecule spectroscopy (CoSMoS) has proven to be a useful method for studying the composition, kinetics and mechanisms of complex cellular machines. Key to the technique is the ability to simultaneously monitor multiple proteins and/or nucleic acids as they interact with one another. Here we describe a protocol for constructing a CoSMoS micromirror total internal reflection fluorescence microscope (mmTIRFM). Design and construction of a scientific microscope often requires a number of custom components and a substantial time commitment. In our protocol, we have streamlined this process by implementation of a commercially available microscopy platform designed to accommodate the optical components necessary for an mmTIRFM. The mmTIRF system eliminates the need for machining custom parts by the end user and facilitates optical alignment. Depending on the experience level of the microscope builder, these time savings and the following protocol can enable mmTIRF construction to be completed within 2 months.

41 CFR 102-76.30 - What seismic safety standards must Federal agencies follow in the design and construction of...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (Continued) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 76-DESIGN AND CONSTRUCTION Design and Construction... 41 Public Contracts and Property Management 3 2013-07-01 2013-07-01 false What seismic safety standards must Federal agencies follow in the design and construction of Federal facilities? 102-76.30...

41 CFR 102-76.30 - What seismic safety standards must Federal agencies follow in the design and construction of...

Code of Federal Regulations, 2011 CFR

2011-01-01

... (Continued) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 76-DESIGN AND CONSTRUCTION Design and Construction... 41 Public Contracts and Property Management 3 2011-01-01 2011-01-01 false What seismic safety standards must Federal agencies follow in the design and construction of Federal facilities? 102-76.30...

41 CFR 102-76.30 - What seismic safety standards must Federal agencies follow in the design and construction of...

Code of Federal Regulations, 2014 CFR

2014-01-01

... (Continued) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 76-DESIGN AND CONSTRUCTION Design and Construction... 41 Public Contracts and Property Management 3 2014-01-01 2014-01-01 false What seismic safety standards must Federal agencies follow in the design and construction of Federal facilities? 102-76.30...

41 CFR 102-76.30 - What seismic safety standards must Federal agencies follow in the design and construction of...

Code of Federal Regulations, 2012 CFR

2012-01-01

... (Continued) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 76-DESIGN AND CONSTRUCTION Design and Construction... 41 Public Contracts and Property Management 3 2012-01-01 2012-01-01 false What seismic safety standards must Federal agencies follow in the design and construction of Federal facilities? 102-76.30...

41 CFR 102-76.30 - What seismic safety standards must Federal agencies follow in the design and construction of...

Code of Federal Regulations, 2010 CFR

2010-07-01

... (Continued) FEDERAL MANAGEMENT REGULATION REAL PROPERTY 76-DESIGN AND CONSTRUCTION Design and Construction... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false What seismic safety standards must Federal agencies follow in the design and construction of Federal facilities? 102-76.30...

49 CFR 178.277 - Requirements for the design, construction, inspection and testing of portable tanks intended for...

Code of Federal Regulations, 2011 CFR

2011-10-01

... design pressure in the ASME Code, Section VIII (IBR, see § 171.7 of this subchapter). Holding time is the... 49 Transportation 3 2011-10-01 2011-10-01 false Requirements for the design, construction... FOR PACKAGINGS Specifications for Portable Tanks § 178.277 Requirements for the design, construction...

49 CFR 178.277 - Requirements for the design, construction, inspection and testing of portable tanks intended for...

Code of Federal Regulations, 2012 CFR

2012-10-01

... design pressure in the ASME Code, Section VIII (IBR, see § 171.7 of this subchapter). Holding time is the... 49 Transportation 3 2012-10-01 2012-10-01 false Requirements for the design, construction... FOR PACKAGINGS Specifications for Portable Tanks § 178.277 Requirements for the design, construction...

49 CFR 178.277 - Requirements for the design, construction, inspection and testing of portable tanks intended for...

Code of Federal Regulations, 2014 CFR

2014-10-01

... design pressure in the ASME Code, Section VIII (IBR, see § 171.7 of this subchapter). Holding time is the... 49 Transportation 3 2014-10-01 2014-10-01 false Requirements for the design, construction... FOR PACKAGINGS Specifications for Portable Tanks § 178.277 Requirements for the design, construction...

49 CFR 178.277 - Requirements for the design, construction, inspection and testing of portable tanks intended for...

Code of Federal Regulations, 2010 CFR

2010-10-01

... design pressure in the ASME Code, Section VIII (IBR, see § 171.7 of this subchapter). Holding time is the... 49 Transportation 2 2010-10-01 2010-10-01 false Requirements for the design, construction... FOR PACKAGINGS Specifications for Portable Tanks § 178.277 Requirements for the design, construction...

49 CFR 178.277 - Requirements for the design, construction, inspection and testing of portable tanks intended for...

Code of Federal Regulations, 2013 CFR

2013-10-01

... design pressure in the ASME Code, Section VIII (IBR, see § 171.7 of this subchapter). Holding time is the... 49 Transportation 3 2013-10-01 2013-10-01 false Requirements for the design, construction... FOR PACKAGINGS Specifications for Portable Tanks § 178.277 Requirements for the design, construction...

Implementation of sustainable and green design and construction practices for bridges.

DOT National Transportation Integrated Search

2012-12-01

The focus of this research is to develop a framework for more sustainable design and construction : processes for new bridges, and sustainable maintenance practices for existing bridges. The framework : includes a green rating system for bridges. The...

A supermolecular building approach for the design and construction of metal-organic frameworks.

PubMed

Guillerm, Vincent; Kim, Dongwook; Eubank, Jarrod F; Luebke, Ryan; Liu, Xinfang; Adil, Karim; Lah, Myoung Soo; Eddaoudi, Mohamed

2014-08-21

In this review, we describe two recently implemented conceptual approaches facilitating the design and deliberate construction of metal–organic frameworks (MOFs), namely supermolecular building block (SBB) and supermolecular building layer (SBL) approaches. Our main objective is to offer an appropriate means to assist/aid chemists and material designers alike to rationally construct desired functional MOF materials, made-to-order MOFs. We introduce the concept of net-coded building units (net-cBUs), where precise embedded geometrical information codes uniquely and matchlessly a selected net, as a compelling route for the rational design of MOFs. This concept is based on employing pre-selected 0-periodic metal–organic polyhedra or 2-periodic metal–organic layers, SBBs or SBLs respectively, as a pathway to access the requisite net-cBUs. In this review, inspired by our success with the original rht-MOF, we extrapolated our strategy to other known MOFs via their deconstruction into more elaborate building units (namely polyhedra or layers) to (i) elucidate the unique relationship between edge-transitive polyhedra or layers and minimal edge-transitive 3-periodic nets, and (ii) illustrate the potential of the SBB and SBL approaches as a rational pathway for the design and construction of 3-periodic MOFs. Using this design strategy, we have also identified several new hypothetical MOFs which are synthetically targetable.

Building code compliance and enforcement: The experience of San Francisco's residential energy conservation ordinance and California's building standards for new construction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vine, E.

1990-11-01

As part of Lawrence Berkeley Laboratory's (LBL) technical assistance to the Sustainable City Project, compliance and enforcement activities related to local and state building codes for existing and new construction were evaluated in two case studies. The analysis of the City of San Francisco's Residential Energy Conservation Ordinance (RECO) showed that a limited, prescriptive energy conservation ordinance for existing residential construction can be enforced relatively easily with little administrative costs, and that compliance with such ordinances can be quite high. Compliance with the code was facilitated by extensive publicity, an informed public concerned with the cost of energy and knowledgeablemore » about energy efficiency, the threat of punishment (Order of Abatement), the use of private inspectors, and training workshops for City and private inspectors. The analysis of California's Title 24 Standards for new residential and commercial construction showed that enforcement of this type of code for many climate zones is more complex and requires extensive administrative support for education and training of inspectors, architects, engineers, and builders. Under this code, prescriptive and performance approaches for compliance are permitted, resulting in the demand for alternative methods of enforcement: technical assistance, plan review, field inspection, and computer analysis. In contrast to existing to construction, building design and new materials and construction practices are of critical importance in new construction, creating a need for extensive technical assistance and extensive interaction between enforcement personnel and the building community. Compliance problems associated with building design and installation did occur in both residential and nonresidential buildings. 12 refs., 5 tabs.« less

Design and application of BIM based digital sand table for construction management

NASA Astrophysics Data System (ADS)

Fuquan, JI; Jianqiang, LI; Weijia, LIU

2018-05-01

This paper explores the design and application of BIM based digital sand table for construction management. Aiming at the demands and features of construction management plan for bridge and tunnel engineering, the key functional features of digital sand table should include three-dimensional GIS, model navigation, virtual simulation, information layers, and data exchange, etc. That involving the technology of 3D visualization and 4D virtual simulation of BIM, breakdown structure of BIM model and project data, multi-dimensional information layers, and multi-source data acquisition and interaction. Totally, the digital sand table is a visual and virtual engineering information integrated terminal, under the unified data standard system. Also, the applications shall contain visual constructing scheme, virtual constructing schedule, and monitoring of construction, etc. Finally, the applicability of several basic software to the digital sand table is analyzed.

Construction of In-house Databases in a Corporation

NASA Astrophysics Data System (ADS)

Okuda, Yasukazu; Yoshikawa, Ichirou; Sasano, Fumio

The authors describe the outline and the construction process of the in-house technical information system of Mitsui Petrochemical Industries Ltd., “MITOLIS”. This system was constructed in 1981 and has been improved since then to make better use of in-house technical reports. Bibliographic data and keywords of technical reports of R & D division are stored in the host computer system in Iwakuni and can be retrieved by the company members on the desk-side terminal connected to the local area network (LAN). The number of stored reports reaches 6100 from 1970 to 1987.

Technology Solutions Case Study: Design Guidance for Passive Vents in New Construction, Multifamily Buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

In an effort to improve indoor air quality in high-performance, new construction, multifamily buildings, dedicated sources of outdoor air are being implemented. Passive vents are being selected by some design teams over other strategies because of their lower first costs and operating costs. The U.S. Department of Energy’s Building America research team Consortium for Advanced Residential Buildings constructed eight steps, which outline the design and commissioning required for these passive vents to perform as intended.

"State of the Art" of technical protection measures in Austria and the effectiveness documented during bedload and debris flow events

NASA Astrophysics Data System (ADS)

Moser, Markus; Mehlhorn, Susanne; Rudolf-Miklau, Florian; Suda, Jürgen

2017-04-01

Since the beginning of systematic torrent control in Austria 130 years ago, barriers are constructed for protection purposes. Until the end of the 1960s, solid barriers were built at the exits of depositional areas to prevent dangerous debris flows from reaching high consequence areas. The development of solid barriers with large slots or slits to regulate sediment transport began with the use of reinforced concrete during the 1970s (Rudolf-Miklau, Suda 2011). In order to dissipate the energy of debris flows debris flow breakers have been designed since the 1980s. By slowing and depositing the surge front of the debris flow, downstream reaches of the stream channel and settlement areas should be exposed to considerably lower dynamic impact. In the past, the technological development of these constructions was only steered by the experiences of the engineering practice while an institutionalized process of standardization comparable to other engineering branches was not existent. In future all structures have to be designed and dimensioned according to the EUROCODE standards. This was the reason to establish an interdisciplinary working group (ON-K 256) at the Austrian Standards Institute (ASI), which has managed to developed comprehensive new technical standards for torrent control engineering, including load models, design, dimensioning and life cycle assessment of torrent control works (technical standard ONR 24800 - series). Extreme torrential events comprise four definable displacement processes floods; fluvial solid transport; hyper-concentrated solid transport (debris floods) and debris flow (stony debris flow or mud-earth flow). As a rule, the design of the torrential barriers has to follow its function (Kettl, 1984). Modern protection concepts in torrent control are scenario-oriented and try to optimize different functions in a chain of protections structures (function chain). More or less the first step for the designing the optimal construction type is

10 CFR 435.6 - Sustainable principles for siting, design and construction. [Reserved

Code of Federal Regulations, 2011 CFR

2011-01-01

... FOR NEW FEDERAL LOW-RISE RESIDENTIAL BUILDINGS Mandatory Energy Efficiency Standards for Federal Low-Rise Residential Buildings. § 435.6 Sustainable principles for siting, design and construction...

10 CFR 435.6 - Sustainable principles for siting, design and construction. [Reserved

Code of Federal Regulations, 2010 CFR

2010-01-01

... FOR NEW FEDERAL LOW-RISE RESIDENTIAL BUILDINGS Mandatory Energy Efficiency Standards for Federal Low-Rise Residential Buildings. § 435.6 Sustainable principles for siting, design and construction...

Construction cost forecast model : model documentation and technical notes.

DOT National Transportation Integrated Search

2013-05-01

Construction cost indices are generally estimated with Laspeyres, Paasche, or Fisher indices that allow changes : in the quantities of construction bid items, as well as changes in price to change the cost indices of those items. : These cost indices...

Trends in highway construction costs in Louisiana : technical summary.

DOT National Transportation Integrated Search

1999-09-01

The objectives of this study are to observe past trends in highway construction costs in Louisiana, identify factors that determine these costs, quantify their impact, and establish a model that can be used to predict future construction cost in Loui...

36 CFR 223.38 - Standards for road design and construction.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 36 Parks, Forests, and Public Property 2 2014-07-01 2014-07-01 false Standards for road design and construction. 223.38 Section 223.38 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE SALE AND DISPOSAL OF NATIONAL FOREST SYSTEM TIMBER, SPECIAL FOREST PRODUCTS, AND FOREST BOTANICAL PRODUCTS Timber Sale Contracts...

Case study of restaurant successfully designed, constructed, and operated for excellent dining acoustics

NASA Astrophysics Data System (ADS)

Bollard, Paul; Des Jardins, Stephen

2005-09-01

Prior to the construction of La Provence Restaurant in Roseville, California in 2004, the owner, Stephen Des Jardins, traveled with his cook, architect, and engineer to the Provence Region of France to study the cuisine, architecture, and acoustics of the local restaurants. This information was incorporated into the design, construction, and operation of his restaurant, with acoustical design assistance provided by the author, Paul Bollard. The result of the owner's painstaking attention to detail is a restaurant which has received very positive reviews for its architecture, quality of food, service, and acoustic ambience. This paper documents the measures included in the construction of the restaurant to ensure that the building acoustics enhance the dining experience, rather than detract from it. Photographs of acoustic treatments are included, as are reverberation time (RT60) test results and ambient noise level measurement results.

Construction of a multimedia application on public network

NASA Astrophysics Data System (ADS)

Liu, Jang; Wang, Chwan-Huei; Tseng, Ming-Yu; Hsiao, Sun-Lang; Luo, Wen-Hen; Tseng, Yung-Mean; Hung, Feng-Yue

1994-04-01

This paper describes our perception of current developments in networking, telecommunication and technology of multimedia. As such, we have taken a constructive view. From this standpoint, we devised a client server architecture that veils servers from their customers. It adheres to our conviction that network and location independence for serve access is a future trend. We have constructed an on-line KARAOKE on an existing CVS (Chinese Videotex System) to test the workability of this architecture and it works well. We are working on a prototype multimedia service network which is a miniature client server structure of our proposal. A specially designed protocol is described. Through this protocol, an one-to-many connection can be set up and to provide for multimedia applications, new connections can be established within a basic connection. So continuous media may have their own connections without being interrupted by other media, at least from the view of an application. We have advanced a constructive view which is not a framework itself. But it is tantamount to a framework, in building systems as assembly of methods, technics, designs, and ideas. This is what a framework does with more flexibility and availability.

Ideas for clear technical writing

USGS Publications Warehouse

Robinson, B.P.

1984-01-01

The three greatest obstacles to clear technical-report writing are probably (1) imprecise words, (2) wordiness, and (3) poorly constructed sentences. Examples of category 1 include abstract words, jargon, and vogue words; of category 2, sentences containing impersonal construction superfluous words; and of category 3, sentences lacking parallel construction and proper order of related words and phrases. These examples and other writing-related subjects are discussed in the report, which contains a cross-referenced index and 24 references.

A worksite prevention program for construction workers: design of a randomized controlled trial.

PubMed

Oude Hengel, Karen M; Joling, Catelijne I; Proper, Karin I; Blatter, Birgitte M; Bongers, Paulien M

2010-06-14

A worksite prevention program was developed to promote the work ability of construction workers and thereby prolong a healthy working life. The objective of this paper is to present the design of a randomized controlled trial evaluating the effectiveness of that intervention program compared with usual care for construction workers. The study is designed as a randomized controlled trial with a follow-up of one year. Employees eligible for this study are construction workers performing actual construction work. The worksite intervention will be compared with usual care. This intervention was developed by using the Intervention Mapping approach and consists of the following components: (1) two individual training sessions of a physical therapist to lower the physical workload, (2) a Rest-Break tool to improve the balance between work and recovery, and (3) two empowerment training sessions to increase the influence of the construction workers at the worksite. Outcome measures are assessed at baseline, 3, 6, and 12 months. The primary outcome measures of this study are work ability and health-related quality of life. Secondary outcome measures include need for recovery, musculoskeletal complaints, work engagement and self efficacy. Cost-effectiveness will be evaluated from the company perspective. Moreover, a process evaluation will be conducted. The feasibility of the intervention and the study has been enhanced by creating an intervention program that explicitly appeals to construction workers and will not interfere too much with the ongoing construction. The feasibility and effectiveness of this worksite prevention program will be investigated by means of an effect- and a process evaluation. If proven effective, this worksite prevention program can be implemented on a larger scale within the construction industry. NTR1278.

Technical and Regulatory Guidance Document for Constructed Treatment Wetlands

DTIC Science & Technology

2003-12-01

leachate and acid mine drainage. The purpose of this document is to provide technical and regulatory guidance to help regulators, industry, consultants...Contaminants at Industrial Facilities .....................41 Table 4-12 Typical Landfill Leachate Characteristics and Removal Efficiencies...43 Table 4-14 Landfill Leachate Characteristics

RESEARCH AND DESIGN ABOUT VERSATILE 3D-CAD ENGINE FOR CONSTRUCTION

NASA Astrophysics Data System (ADS)

Tanaka, Shigenori; Kubota, Satoshi; Kitagawa, Etsuji; Monobe, Kantaro; Nakamura, Kenji

In the construction field of Japan, it is an important subject to build the environment where 3D-CAD data is used for CALS/EC, information construction, and an improvement in productivity. However, in the construction field, 3D-CAD software does not exist under the present circumstances. Then, in order to support development of domestic 3D-CAD software, it is required to develop a 3D-CAD engine. In this research, in order to familiarize the 3D-CAD software at low cost and quickly and build the environment where the 3D-CAD software is utilizable, investigation for designing a 3D-CAD engine is proposed. The target for investigation are the use scene of 3D-CAD, the seeds which accompany 3D-CAD, a standardization trend, existing products, IT component engineering. Based on results of the investigation, the functional requirements for the 3D-CAD engine for the construction field were concluded.

Assessing Whether Students Seek Constructive Criticism: The Design of an Automated Feedback System for a Graphic Design Task

ERIC Educational Resources Information Center

Cutumisu, Maria; Blair, Kristen P.; Chin, Doris B.; Schwartz, Daniel L.

2017-01-01

We introduce a choice-based assessment strategy that measures students' choices to seek constructive feedback and to revise their work. We present the feedback system of a game we designed to assess whether students choose positive or negative feedback and choose to revise their posters in the context of a poster design task, where they learn…

Communication Network Design: West Ottawa School District.

ERIC Educational Resources Information Center

Couch, David deS.

This report describes the technical details and rationale behind the decisions in the design and development of the communications network installed as part of a 1991-1993 district-wide construction project in the West Ottawa Public Schools (Michigan). The project called for development of a communications network to carry voice, data, and video…

1981 Bibliography of Technical Writing.

ERIC Educational Resources Information Center

Book, Virginia Alm; And Others

1982-01-01

Offers resources on technical writing published in 1981. Arranges the citations under the following categories: bibliographies, books, reviews, and articles on the profession; theory and philosophy; pedagogy; technical speech; research; designing degree programs; technical writing and the computer; writing technical articles and reports;…

Design and construction of PCC pavements, volume 2 : design features and practices that influence performance of pavements.

DOT National Transportation Integrated Search

1998-10-01

A study has been conducted to evaluate and analyze portland cement concrete (PCC) pavements in order to : develop recommendations for the design and construction of long-lived concrete pavements. It involved a : detailed evaluation and analysis of th...

Design and construction of a full-scale lateral impact testing facility.

DOT National Transportation Integrated Search

2015-05-01

The goal of this work is to design and construct a full scale lateral impact testing facility that is capable of recreating the damage that would be created by an overheight vehicle collision. This was accomplished by impacting a test specimen with 8...

Esthetic abutment design for angulated screw channels: A technical report.

PubMed

Sakamoto, Satoshi; Ro, Munehiko; Al Ardah, Aladdin; Goodacre, Charles

2017-11-15

Angulated screw channel system abutments (ASCs) have recently been introduced to address the problem with visible screw access that may compromise esthetics. ASCs allow the screw access to be modified up to 25 degrees relative to the implant axis. However, a widened channel, which may cause thinning of the facial ceramic, is needed at the implant screw head to allow for proper engagement of the screwdriver. This technical report introduces a custom titanium insert design, the Satoshi Sakamoto (SS) abutment. The SS abutment consists of a custom titanium metal insert and zirconia coping in which the access hole is located in an esthetic position with an ASC system. The SS abutment results in a crown with more normal crown dimensions that also provides more space for the soft tissues. This SS abutment design allows clinicians to obtain screw-retained restorations with optimal esthetics and mechanical strength. Copyright © 2017 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

LADES: a software for constructing and analyzing longitudinal designs in biomedical research.

PubMed

Vázquez-Alcocer, Alan; Garzón-Cortes, Daniel Ladislao; Sánchez-Casas, Rosa María

2014-01-01

One of the most important steps in biomedical longitudinal studies is choosing a good experimental design that can provide high accuracy in the analysis of results with a minimum sample size. Several methods for constructing efficient longitudinal designs have been developed based on power analysis and the statistical model used for analyzing the final results. However, development of this technology is not available to practitioners through user-friendly software. In this paper we introduce LADES (Longitudinal Analysis and Design of Experiments Software) as an alternative and easy-to-use tool for conducting longitudinal analysis and constructing efficient longitudinal designs. LADES incorporates methods for creating cost-efficient longitudinal designs, unequal longitudinal designs, and simple longitudinal designs. In addition, LADES includes different methods for analyzing longitudinal data such as linear mixed models, generalized estimating equations, among others. A study of European eels is reanalyzed in order to show LADES capabilities. Three treatments contained in three aquariums with five eels each were analyzed. Data were collected from 0 up to the 12th week post treatment for all the eels (complete design). The response under evaluation is sperm volume. A linear mixed model was fitted to the results using LADES. The complete design had a power of 88.7% using 15 eels. With LADES we propose the use of an unequal design with only 14 eels and 89.5% efficiency. LADES was developed as a powerful and simple tool to promote the use of statistical methods for analyzing and creating longitudinal experiments in biomedical research.

Technical noise supplement : TeNS : a technical supplement to the Traffic Noise Analysis Protocol.

DOT National Transportation Integrated Search

1998-10-01

The purpose of this Technical Noise Supplement (TeNS) is to provide technical background : information on transportation-related noise in general and highway traffic noise in : particular. It is designed to elaborate on technical concepts and procedu...

UOE Pipe Manufacturing Process Simulation: Equipment Designing and Construction

NASA Astrophysics Data System (ADS)

Delistoian, Dmitri; Chirchor, Mihael

2017-12-01

UOE pipe manufacturing process influence directly on pipeline resilience and operation capacity. At present most spreaded pipe manufacturing method is UOE. This method is based on cold forming. After each technological step appears a certain stress and strain level. For pipe stress strain study is designed and constructed special equipment that simulate entire technological process.UOE pipe equipment is dedicated for manufacturing of longitudinally submerged arc welded DN 400 (16 inch) steel pipe.

Design and construction of PCC pavements. Volume 2, design features and practices that influence performance of pavements

DOT National Transportation Integrated Search

1998-10-01

A study has been conducted to evaluate and analyze Portland cement concrete (PCC) pavements in order to develop recommendations for the design and construction of long-lived concrete pavements. In involved a detailed evaluation and analysis of the PC...

Teaching Power Electronics with a Design-Oriented, Project-Based Learning Method at the Technical University of Denmark

ERIC Educational Resources Information Center

Zhang, Zhe; Hansen, Claus Thorp; Andersen, Michael A. E.

2016-01-01

Power electronics is a fast-developing technology within the electrical engineering field. This paper presents the results and experiences gained from applying design-oriented project-based learning to switch-mode power supply design in a power electronics course at the Technical University of Denmark (DTU). Project-based learning (PBL) is known…

Engineering Technical Review Planning Briefing

NASA Technical Reports Server (NTRS)

Gardner, Terrie

2012-01-01

The general topics covered in the engineering technical planning briefing are 1) overviews of NASA, Marshall Space Flight Center (MSFC), and Engineering, 2) the NASA Systems Engineering(SE) Engine and its implementation , 3) the NASA Project Life Cycle, 4) MSFC Technical Management Branch Services in relation to the SE Engine and the Project Life Cycle , 5) Technical Reviews, 6) NASA Human Factor Design Guidance , and 7) the MSFC Human Factors Team. The engineering technical review portion of the presentation is the primary focus of the overall presentation and will address the definition of a design review, execution guidance, the essential stages of a technical review, and the overall review planning life cycle. Examples of a technical review plan content, review approaches, review schedules, and the review process will be provided and discussed. The human factors portion of the presentation will focus on the NASA guidance for human factors. Human factors definition, categories, design guidance, and human factor specialist roles will be addressed. In addition, the NASA Systems Engineering Engine description, definition, and application will be reviewed as background leading into the NASA Project Life Cycle Overview and technical review planning discussion.

33 CFR 148.725 - What are the design, construction and operational criteria?

Code of Federal Regulations, 2011 CFR

2011-07-01

... the basis of how well they: (a) Reflect the use of best available technology in design, construction...) Maximize use of existing facilities; (i) Provide personnel trained in oil spill prevention at critical...

33 CFR 148.725 - What are the design, construction and operational criteria?

Code of Federal Regulations, 2012 CFR

2012-07-01

... the basis of how well they: (a) Reflect the use of best available technology in design, construction...) Maximize use of existing facilities; (i) Provide personnel trained in oil spill prevention at critical...

RADON PREVENTION IN THE DESIGN AND CONSTRUCTION OF SCHOOLS AND OTHER LARGE BUILDINGS

EPA Science Inventory

The paper discusses radon prevention in the design and construction of schools and other large buildings. ased on studies in progress for the past 3 years, the U.S. EPA's Office of Research and Development (ORD) has started incorporating radon control measures into the design and...

HYNOL PROCESS ENGINEERING: PROCESS CONFIGURATION, SITE PLAN, AND EQUIPMENT DESIGN

EPA Science Inventory

The report describes the design of the hydropyrolysis reactor system of the Hynol process. (NOTE: A bench scale methanol production facility is being constructed to demonstrate the technical feasibility of producing methanol from biomass using the Hynol process. The plant is bein...

Design and construction of a photobioreactor for hydrogen production, including status in the field.

PubMed

Skjånes, Kari; Andersen, Uno; Heidorn, Thorsten; Borgvang, Stig A

Several species of microalgae and phototrophic bacteria are able to produce hydrogen under certain conditions. A range of different photobioreactor systems have been used by different research groups for lab-scale hydrogen production experiments, and some few attempts have been made to upscale the hydrogen production process. Even though a photobioreactor system for hydrogen production does require special construction properties (e.g., hydrogen tight, mixing by other means than bubbling with air), only very few attempts have been made to design photobioreactors specifically for the purpose of hydrogen production. We have constructed a flat panel photobioreactor system that can be used in two modes: either for the cultivation of phototrophic microorganisms (upright and bubbling) or for the production of hydrogen or other anaerobic products (mixing by "rocking motion"). Special emphasis has been taken to avoid any hydrogen leakages, both by means of constructional and material choices. The flat plate photobioreactor system is controlled by a custom-built control system that can log and control temperature, pH, and optical density and additionally log the amount of produced gas and dissolved oxygen concentration. This paper summarizes the status in the field of photobioreactors for hydrogen production and describes in detail the design and construction of a purpose-built flat panel photobioreactor system, optimized for hydrogen production in terms of structural functionality, durability, performance, and selection of materials. The motivations for the choices made during the design process and advantages/disadvantages of previous designs are discussed.

Design and optimisation of novel configurations of stormwater constructed wetlands

NASA Astrophysics Data System (ADS)

Kiiza, Christopher

2017-04-01

Constructed wetlands (CWs) are recognised as a cost-effective technology for wastewater treatment. CWs have been deployed and could be retrofitted into existing urban drainage systems to prevent surface water pollution, attenuate floods and act as sources for reusable water. However, there exist numerous criteria for design configuration and operation of CWs. The aim of the study was to examine effects of design and operational variables on performance of CWs. To achieve this, 8 novel designs of vertical flow CWs were continuously operated and monitored (weekly) for 2years. Pollutant removal efficiency in each CW unit was evaluated from physico-chemical analyses of influent and effluent water samples. Hybrid optimised multi-layer perceptron artificial neural networks (MLP ANNs) were applied to simulate treatment efficiency in the CWs. Subsequently, predictive and analytical models were developed for each design unit. Results show models have sound generalisation abilities; with various design configurations and operational variables influencing performance of CWs. Although some design configurations attained faster and higher removal efficiencies than others; all 8 CW designs produced effluents permissible for discharge into watercourses with strict regulatory standards.

MDOT implementation plan for GPS technology in planning, design, and construction delivery

DOT National Transportation Integrated Search

2010-09-13

Global Positioning System (GPS) technology offers advantages to transportation agencies in the planning, design and construction stages of project delivery. This research study will develop a guide for Mississippi Department of Transportation (MDOT) ...

33 CFR 86.23 - Construction.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 1 2012-07-01 2012-07-01 false Construction. 86.23 Section 86.23 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INLAND NAVIGATION RULES ANNEX III: TECHNICAL DETAILS OF SOUND SIGNAL APPLIANCES Bell or Gong § 86.23 Construction. Bells and gongs...

33 CFR 86.23 - Construction.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Construction. 86.23 Section 86.23 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INLAND NAVIGATION RULES ANNEX III: TECHNICAL DETAILS OF SOUND SIGNAL APPLIANCES Bell or Gong § 86.23 Construction. Bells and gongs...

33 CFR 86.23 - Construction.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false Construction. 86.23 Section 86.23 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INLAND NAVIGATION RULES ANNEX III: TECHNICAL DETAILS OF SOUND SIGNAL APPLIANCES Bell or Gong § 86.23 Construction. Bells and gongs...

33 CFR 86.23 - Construction.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false Construction. 86.23 Section 86.23 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INLAND NAVIGATION RULES ANNEX III: TECHNICAL DETAILS OF SOUND SIGNAL APPLIANCES Bell or Gong § 86.23 Construction. Bells and gongs...

33 CFR 86.23 - Construction.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false Construction. 86.23 Section 86.23 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY INLAND NAVIGATION RULES ANNEX III: TECHNICAL DETAILS OF SOUND SIGNAL APPLIANCES Bell or Gong § 86.23 Construction. Bells and gongs...

Final Technical Report, Wind Generator Project (Ann Arbor)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Geisler, Nathan

A Final Technical Report (57 pages) describing educational exhibits and devices focused on wind energy, and related outreach activities and programs. Project partnership includes the City of Ann Arbor, MI and the Ann Arbor Hands-on Museum, along with additional sub-recipients, and U.S. Department of Energy/Office of Energy Efficiency and Renewable Energy (EERE). Report relays key milestones and sub-tasks as well as numerous graphics and images of five (5) transportable wind energy demonstration devices and five (5) wind energy exhibits designed and constructed between 2014 and 2016 for transport and use by the Ann Arbor Hands-on Museum.

Technical Subjects in Secondary Schools

ERIC Educational Resources Information Center

Howard, A. E.

2008-01-01

Purpose: This paper aims to examine technical education in various types of secondary schools, and suggests three levels of technical courses to be taught in secondary schools. Design/methodology/approach: The paper discusses the differences between technical schools and colleges, and vocational technical courses taught in "academic"…

46 CFR 160.170-23 - Procedure for approval of design, material, or construction change.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Procedure for approval of design, material, or construction change. 160.170-23 Section 160.170-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Davit-Launched Liferaft Automatic Release Hooks ...

46 CFR 160.170-23 - Procedure for approval of design, material, or construction change.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Procedure for approval of design, material, or construction change. 160.170-23 Section 160.170-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Davit-Launched Liferaft Automatic Release Hooks ...

A worksite prevention program for construction workers: design of a randomized controlled trial

PubMed Central

2010-01-01

Background A worksite prevention program was developed to promote the work ability of construction workers and thereby prolong a healthy working life. The objective of this paper is to present the design of a randomized controlled trial evaluating the effectiveness of that intervention program compared with usual care for construction workers. Methods The study is designed as a randomized controlled trial with a follow-up of one year. Employees eligible for this study are construction workers performing actual construction work. The worksite intervention will be compared with usual care. This intervention was developed by using the Intervention Mapping approach and consists of the following components: (1) two individual training sessions of a physical therapist to lower the physical workload, (2) a Rest-Break tool to improve the balance between work and recovery, and (3) two empowerment training sessions to increase the influence of the construction workers at the worksite. Outcome measures are assessed at baseline, 3, 6, and 12 months. The primary outcome measures of this study are work ability and health-related quality of life. Secondary outcome measures include need for recovery, musculoskeletal complaints, work engagement and self efficacy. Cost-effectiveness will be evaluated from the company perspective. Moreover, a process evaluation will be conducted. Discussion The feasibility of the intervention and the study has been enhanced by creating an intervention program that explicitly appeals to construction workers and will not interfere too much with the ongoing construction. The feasibility and effectiveness of this worksite prevention program will be investigated by means of an effect- and a process evaluation. If proven effective, this worksite prevention program can be implemented on a larger scale within the construction industry. Trial Registration NTR1278 PMID:20546568

School Retrofit Design Analysis System. A Microcomputer Model for School Energy Use.

ERIC Educational Resources Information Center

Canipe, Stephen Lee

The School Retrofit Design Analysis System (SRDAS) developed in this study provides a non-technical method for the school administrator to use in evaluating alternative energy saving retrofit and new construction design possibilities. By providing a high degree of flexibility, SRDAS is applicable to a wide range of school building and retrofit…

RADON PREVENTION IN THE DESIGN & CONSTRUCTION OF SCHOOLS & OTHER LARGE BUILDINGS

EPA Science Inventory

It is typically easier and much less expensive to design and construct a new building with radon-resistant and/or easy-to-mitigate features, than to add these features after the building is completed and occupied. Therefore, when building in an area with the potential for elevate...

Magnetostatics Analysis, Design, and Construction of a Loudspeaker

NASA Astrophysics Data System (ADS)

Galeriu, Calin

2010-11-01

Making a loudspeaker is a very rewarding hands-on activity that can be used to teach about electro-magnetism and sound waves. Several loudspeaker designs have been described in this magazine.1-4 The simplest loudspeaker4 has only a magnet, a coil, and three plastic cups. The simpler devices3,4 require a powerful amplified output, e.g., from a boom box. The more complex devices1,2 can operate using the smaller electric current from a CD player earphone output. Unfortunately, the procedure to make a more efficient loudspeaker is lengthy and less recommended to some high school students, involving a hot glue gun, a safety razor, five-minute epoxy, etc. Our loudspeaker, a variation of Heller's,2 is both simple in construction and efficient in operation. An analysis of the magnetic field distribution helped us in the design of this loudspeaker.

Systems scenarios: a tool for facilitating the socio-technical design of work systems.

PubMed

Hughes, Helen P N; Clegg, Chris W; Bolton, Lucy E; Machon, Lauren C

2017-10-01

The socio-technical systems approach to design is well documented. Recognising the benefits of this approach, organisations are increasingly trying to work with systems, rather than their component parts. However, few tools attempt to analyse the complexity inherent in such systems, in ways that generate useful, practical outputs. In this paper, we outline the 'System Scenarios Tool' (SST), which is a novel, applied methodology that can be used by designers, end-users, consultants or researchers to help design or re-design work systems. The paper introduces the SST using examples of its application, and describes the potential benefits of its use, before reflecting on its limitations. Finally, we discuss potential opportunities for the tool, and describe sets of circumstances in which it might be used. Practitioner Summary: The paper presents a novel, applied methodological tool, named the 'Systems Scenarios Tool'. We believe this tool can be used as a point of reference by designers, end-users, consultants or researchers, to help design or re-design work systems. Included in the paper are two worked examples, demonstrating the tool's application.

Optimizing the Construction of the A1 Collaboration Neutron Detector

NASA Astrophysics Data System (ADS)

Chinn, Edward; A1 Collaboration

2016-09-01

We report on the design and construction of a frame designed to optimize both the time efficiency and construction quality of the large scintillator elements These elements will be assembled to form a neutron detector for use by the A1 Collaboration at the Institute for Nuclear Physics in Mainz, Germany. The design had to provide adequate support for the 20 kg scintillator bars while gluing light guides and photomultiplier tubes to both sides of the bars using optical cement. The optical cement requires approximately 24 hours to dry and 100 bars have to be glued with this apparatus. To address each of these issues, several different prototypes were designed and reviewed. The selected apparatus minimized size to meet space constraints, with reduced material cost and provided the most time-efficient way to build the neutron detector. Once the schematic design was selected, we produced technical drawings in AutoDesk Inventor. Assembled the structure and completed gluing of the first batch of scintillators, in order to verify the performance. This apparatus was successful at producing high quality scintillators which were evaluated using cosmic rays. National Science Foundation Grant No. IIA-1358175.

46 CFR 160.133-23 - Procedure for approval of design, material, or construction change.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Procedure for approval of design, material, or construction change. 160.133-23 Section 160.133-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Release Mechanisms for Lifeboats and Rescue Boats §...

46 CFR 160.133-23 - Procedure for approval of design, material, or construction change.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Procedure for approval of design, material, or construction change. 160.133-23 Section 160.133-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Release Mechanisms for Lifeboats and Rescue Boats ...

Design and Construction of a Multi-wavelength, Micromirror Total Internal Reflectance Fluorescence Microscope

PubMed Central

Larson, Joshua; Kirk, Matt; Drier, Eric A.; O’Brien, William; MacKay, James F.; Friedman, Larry; Hoskins, Aaron

2015-01-01

Colocalization Single Molecule Spectroscopy (CoSMoS) has proven to be a useful method for studying the composition, kinetics, and mechanisms of complex cellular machines. Key to the technique is the ability to simultaneously monitor multiple proteins and/or nucleic acids as they interact with one another. Here we describe a protocol for constructing a CoSMoS micromirror Total Internal Reflection Fluorescence Microscope (mmTIRFM). Design and construction of a scientific microscope often requires a number of custom components and a significant time commitment. In our protocol, we have streamlined this process by implementation of a commercially available microscopy platform designed to accommodate the optical components necessary for a mmTIRFM. The mmTIRF system eliminates the need for machining custom parts by the end-user and facilitates optical alignment. Depending on the experience-level of the microscope builder, these time-savings and the following protocol can enable mmTIRF construction to be completed within two months. PMID:25188633

Additional Final Area Designations and Technical Amendment for the 2012 Annual Fine Particle Standard Established in 2012 - Mar 2015

EPA Pesticide Factsheets

EPA is establishing or revising initial area designations and a technical amendment to correct an inadvertent error in the initial designation for one area for the 2012 annual national ambient air quality standards for fine particle pollution.

Design, Construction, Demonstration and Delivery of an Automated Narrow Gap Welding System.

DTIC Science & Technology

1983-03-31

evaluated on the Narrow Gap welding system. By using the combinational qas shielding assembly, it is now possible to reduce the gas flow rates to a value...AD-A145 496 DESIGN CONSTRUCTION DEMONSTRATION AND DE IVER OF AN AUTOMATED NARROW GAP WELDING SYSTEM(U) CRC AUTOMATIC WELDING CO HODSTON SX 31 MAR 83...STANDARDS-963 - A CRC REPORT NO. NAV A/W 7 0PHASE 3 REPORT ON SDESIGN, CONSTRUCTION, DEMONSTRATION AND DELIVERY OF AN AUTOMATED NARROW GAP WELDING

A bootstrap lunar base: Preliminary design review 2

NASA Technical Reports Server (NTRS)

1987-01-01

A bootstrap lunar base is the gateway to manned solar system exploration and requires new ideas and new designs on the cutting edge of technology. A preliminary design for a Bootstrap Lunar Base, the second provided by this contractor, is presented. An overview of the work completed is discussed as well as the technical, management, and cost strategies to complete the program requirements. The lunar base design stresses the transforming capabilities of its lander vehicles to aid in base construction. The design also emphasizes modularity and expandability in the base configuration to support the long-term goals of scientific research and profitable lunar resource exploitation. To successfully construct, develop, and inhabit a permanent lunar base, however, several technological advancements must first be realized. Some of these technological advancements are also discussed.

Construction Simulation Analysis of 60m-span Concrete Filled Steel Tube arch bridge

NASA Astrophysics Data System (ADS)

Shi, Jing Xian; Ding, Qing Hua

2018-06-01

The construction process of the CFST arch bridge is complicated. The construction process not only affects the structural stress in the installation, but also determines the form a bridge and internal force of the bridge. In this paper, a 60m span concrete filled steel tube tied arch bridge is taken as the background, and a three-dimensional finite element simulation model is established by using the MIDAS/Civil bridge structure analysis software. The elevation of the main arch ring, the beam stress, the forces in hanger rods and the modal frequency of the main arch during the construction stage are calculated, and the construction process is simulated and analyzed. Effectively and reasonably guide the construction and ensure that the line and force conditions of the completed bridge meet the design requirements and provides a reliable technical guarantee for the safe construction of the bridge.

Challenges of constructing salt cavern gas storage in China

NASA Astrophysics Data System (ADS)

Xia, Yan; Yuan, Guangjie; Ban, Fansheng; Zhuang, Xiaoqian; Li, Jingcui

2017-11-01

After more than ten years of research and engineering practice in salt cavern gas storage, the engineering technology of geology, drilling, leaching, completion, operation and monitoring system has been established. With the rapid growth of domestic consumption of natural gas, the requirement of underground gas storage is increasing. Because high-quality rock salt resources about 1000m depth are relatively scarce, the salt cavern gas storages will be built in deep rock salt. According to the current domestic conventional construction technical scheme, construction in deep salt formations will face many problems such as circulating pressure increasing, tubing blockage, deformation failure, higher completion risk and so on, caused by depth and the complex geological conditions. Considering these difficulties, the differences between current technical scheme and the construction scheme of twin well and big hole are analyzed, and the results show that the technical scheme of twin well and big hole have obvious advantages in reducing the circulating pressure loss, tubing blockage and failure risk, and they can be the alternative schemes to solve the technical difficulties of constructing salt cavern gas storages in the deep rock salt.

Economic Evaluation of Building Design, Construction, Operation and Maintenance. Seminar Workbook.

ERIC Educational Resources Information Center

Ruegg, Rosalie T.

This workbook has been prepared for participants in the seminar, "Economic Evaluation of Building Design, Construction, Operation and Maintenance." It has two main functions: (1) to provide basic resource materials, references, and introductions to methods employed in the seminar; and (2) to provide instructional problems for solution by…

46 CFR 160.135-23 - Procedure for approval of design, material, or construction change.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Procedure for approval of design, material, or construction change. 160.135-23 Section 160.135-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Lifeboats § 160.135-23 Procedure for approval of...

46 CFR 160.156-23 - Procedure for approval of design, material, or construction change.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Procedure for approval of design, material, or construction change. 160.156-23 Section 160.156-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Rescue Boats and Fast Rescue Boats (SOLAS) § 160.156...

46 CFR 160.156-23 - Procedure for approval of design, material, or construction change.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Procedure for approval of design, material, or construction change. 160.156-23 Section 160.156-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Rescue Boats and Fast Rescue Boats (SOLAS) § 160.156...

46 CFR 160.135-23 - Procedure for approval of design, material, or construction change.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Procedure for approval of design, material, or construction change. 160.135-23 Section 160.135-23 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Lifeboats (SOLAS) § 160.135-23 Procedure for approva...

Technical challenges in designing post-marketing eCRFs to address clinical safety and pharmacovigilance needs.

PubMed

Lu, Zhengwu

2010-01-01

To identify key challenges and propose technical considerations in designing electronic case report form (eCRF) for post-marketing studies, the author undertakes a comprehensive literature review of peer reviewed and grey literature to assess the key aspects, processes, standards, recommendations, and best practices in designing eCRFs based on industry experience in designing and supporting electronic data capture (EDC) studies. Literature search using strings on MEDLINE and PUBMED returned few papers directly related to CRF design. Health informatics and general practice journals were searched and results reviewed. Many conference, government commission, health professional and special interests group websites provide relevant information from practical experience - summarization of this information is presented. Further, we presented a list of concrete technical considerations in dealing with EDC technology/system limitations based on literature assessment and industry implementation experience. It is recognized that cross-functional teams be involved in eCRF design process and decision making. To summarize the keys in designing eCRFs to address post-market study safety and pharmacovigilance needs, the first is to identify required data elements from the study protocol supporting data analyses and reporting requirements. Secondly, accepted best practices, CDASH & CDISC guidelines, and company internal or therapeutic unit standard should be considered and applied. Coding (MedDRA & WHODD) mapping should be managed and implemented as well when possible. Finally, we need to be on top of the EDC technologies, challenge the technologies, drive EDC improvement via working with vendors, and utilize the technologies to drive clinical effectiveness. Copyright (c) 2009 Elsevier Inc. All rights reserved.