Herbert Easterly auxiliary truck heater. Final technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The objective of this work was to continue the development of the Herbert Easterly heater apparatus for vehicles, such as semi-trailer tractors in order to fully establish its technical feasibility and provide the basis for its commercialization. This heater is auxiliary to the vehicle`s primary heating system. With the engine off it heats both the vehicle engine to a temperature at which it starts easily and the vehicle passenger compartment. Specifically, this heater is automatically ignitable, operates directly from the vehicle diesel fuel supply and preheats the vehicle engine fuel prior to combustion. During the course of this work ninemore » different versions of prototype heaters were designed, constructed and tested. All designs were based on the ideas and principles outlined in the Easterly patent. Each successive version incorporated design and fabrication improvements relative to the previous version. The final version, Prototype 9, utilized a multiple water jacket design to capture additional heat from the combustion gases prior to exhausting to the atmosphere. This final prototype exceeded the performance of a commercially available Webasto DBW-2010 using the same commercial burner as the one used in the Webasto unit. The time required to raise the heater fluid temperature by 120{degree}F was 23% less (20 minutes compared to 26 minutes) for Prototype 9 compared to the commercially available unit. In addition a prototype heat exchanger for preheating engine fuel was designed, fabricated and tested. It was also determined that the Prototype 9 auxiliary heater could operate at 85{degree}F for approximately 6 hours on a fully charged 12 volt marine battery rated to deliver 500 cold cranking amps.« less

Feasibility Study for a Computerized Serials Control System in the Defense Communications Agency Technical and Management Information Center.

DTIC Science & Technology

1984-06-20

AD-A162 ±88 FEASIBILITY STUDY FOR A COMPUTERIZED SERIALS CONTROL 1/1 SYSTEM IN THE DEFENS (U) DEFENSE COMMUNICATIONS AGENCY WASHINGTON DC TECHNICAL...NATIONAL BUREAU OF STANDARDS- 1963-A 0FEASIBILITY STUDY FOR A COMPUTERIZED SERIALS CONTROL SYSTEM IN THE DEFENSE COMMUNICATIONS 0AGENCY TECHNICAL AND...ABSTRACT 21. ABSTRACT SECURITY CLASSIFICATION UNCLASSIFIED/UNLIMITED R1 SAME AS RPT. 0 DTIC USERS 0 UNCLASSIFIED 22&. NAME OF RESPONSIBLE INDIVIDUAL 22b

Technical Feasibility Study for Zero Energy K-12 Schools

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pless, Shanti D.; Torcellini, Paul A.; Bonnema, Eric

A simulation-based technical feasibility study was completed to show the types of technologies required to achieve ZEB status with this building type. These technologies are prioritized across the building's subsystem such that design teams can readily integrate the ideas. Energy use intensity (EUI) targets were established for U.S. climate zones such that K-12 schools can be zero-ready or can procure solar panels or other renewable energy production sources to meet the zero energy building definition. Results showed that it is possible for K-12 schools to achieve zero energy when the EUI is between 20 and 26 kBtu/ft2/yr. Temperate climates requiredmore » a smaller percentage of solar panel coverage than very hot or very cold climates. The paper provides a foundation for technically achieving zero energy schools with a vision of transforming the school construction market to mainstream zero energy buildings within typical construction budgets.« less

10 CFR 52.157 - Contents of applications; technical information in final safety analysis report.

Code of Federal Regulations, 2013 CFR

2013-01-01

...; technical information in final safety analysis report. The application must contain a final safety analysis...) Information sufficient to demonstrate compliance with the applicable requirements regarding testing, analysis... 10 Energy 2 2013-01-01 2013-01-01 false Contents of applications; technical information in final...

10 CFR 52.157 - Contents of applications; technical information in final safety analysis report.

Code of Federal Regulations, 2012 CFR

2012-01-01

...; technical information in final safety analysis report. The application must contain a final safety analysis...) Information sufficient to demonstrate compliance with the applicable requirements regarding testing, analysis... 10 Energy 2 2012-01-01 2012-01-01 false Contents of applications; technical information in final...

10 CFR 52.157 - Contents of applications; technical information in final safety analysis report.

Code of Federal Regulations, 2014 CFR

2014-01-01

...; technical information in final safety analysis report. The application must contain a final safety analysis...) Information sufficient to demonstrate compliance with the applicable requirements regarding testing, analysis... 10 Energy 2 2014-01-01 2014-01-01 false Contents of applications; technical information in final...

10 CFR 52.157 - Contents of applications; technical information in final safety analysis report.

Code of Federal Regulations, 2011 CFR

2011-01-01

...; technical information in final safety analysis report. The application must contain a final safety analysis...) Information sufficient to demonstrate compliance with the applicable requirements regarding testing, analysis... 10 Energy 2 2011-01-01 2011-01-01 false Contents of applications; technical information in final...

Troubleshooting Instruction in Vocational-Technical Education Via Dynamic Simulation. Final Report.

ERIC Educational Resources Information Center

Finch, Curtis R.

This study was designed to examine the feasibility of using simulation as a means of teaching vocational-technical students to detect and identify malfunctions in selected electrical and mechanical systems. A dynamic simulator was employed which features interchangeable panels and logic that permits the simulation of electrical or mechanical…

Technical Analysis Feasibility Study on Smart Microgrid System in Sekolah Tinggi Teknik PLN

NASA Astrophysics Data System (ADS)

Suyanto, Heri

2018-02-01

Nowadays application of new and renewable energy as main resource of power plant has greatly increased. High penetration of renewable energy into the grid will influence the quality and reliability of the electricity system, due to the intermittent characteristic of new and renewable energy resources. Smart grid or microgrid technology has the ability to deal with this intermittent characteristic especially if these renewable energy resources integrated to grid in large scale, so it can improve the reliability and efficiency of the grid. We plan to implement smart microgrid system at Sekolah Tinggi Teknik PLN as a pilot project. Before the pilot project start, the feasibility study must be conducted. In this feasibility study, the renewable energy resources and load characteristic at the site will be measured. Then the technical aspect of this feasibility study will be analyzed. This paper explains that analysis of ths feasibility study.

48 CFR 1852.235-73 - Final Scientific and Technical Reports.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Final Scientific and Technical Reports. 1852.235-73 Section 1852.235-73 Federal Acquisition Regulations System NATIONAL..., including recommendations and conclusions based on the experience and results obtained. The final report...

Final Technical Report for ARRA Funding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rusack, Roger; Mans, Jeremiah; Poling, Ronald

Final technical report of the University of Minnesota experimental high energy physics group for ARRA support. The Cryogenic Dark Matter Experiment (CDMS) used the funds received to construct a new passive shield to protect a high-purity germanium detector located in the Soudan mine in Northern Minnesota from cosmic rays. The BESIII and the CMS groups purchased computing hardware to assemble computer farms for data analysis and to generate large volumes of simulated data for comparison with the data collected.

A Computerized Information Retrieval System for the Technical Assistance Center Clearinghouse: A Feasibility Study.

ERIC Educational Resources Information Center

Buckley, Joseph J.

This report first analyzes the need for a Technical Assistance Center (TAC) Clearinghouse, which would provide a range of services including question answering for state and local education agencies, workshop preparation assistance, and literature surveys. Addressing the question of feasibility of a computerized information retrieval system for…

75 FR 77897 - Long Walk National Historic Trail Feasibility Study, Abbreviated Final Environmental Impact...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-14

... DEPARTMENT OF THE INTERIOR National Park Service [7700-1104-SZS] Long Walk National Historic Trail Feasibility Study, Abbreviated Final Environmental Impact Statement, National Trails Intermountain Region, NM... Environmental Impact Statement for the Long Walk National Historic Trail Feasibility Study. SUMMARY: Pursuant to...

Aptahistochemistry in diagnostic pathology: technical scrutiny and feasibility.

PubMed

Bukari, Bakhtiar A; Citartan, Marimuthu; Ch'ng, Ewe Seng; Bilibana, Mawethu P; Rozhdestvensky, Timofey; Tang, Thean-Hock

2017-05-01

Antibodies have been the workhorse for diagnostic immunohistochemistry to specifically interrogate the expression of certain protein to aid in histopathological diagnosis. This review introduces another dimension of histochemistry that employs aptamers as the core tool, the so-called aptahistochemistry. Aptamers are an emerging class of molecular recognition elements that could recapitulate the roles of antibodies. The many advantageous properties of aptamers suited for this diagnostic platform are scrutinized. An in-depth discussion on the technical aspects of aptahistochemistry is provided with close step-by-step comparison to the more familiarized immunohistochemical procedures, namely functionalization of the aptamer as a probe, antigen retrieval, optimization with emphasis on incubation parameters and visualization methods. This review offers rationales to overcome the anticipated challenges in transition from immunohistochemistry to aptahistochemistry, which is deemed feasible for an average diagnostic pathology laboratory.

Technical, economic and environmental feasibility of recycling nutrients in waste in Southern Thailand.

PubMed

Schouw, Nanette Levanius; Bregnhøj, Henrik; Mosbaek, Hans; Tjell, Jens Christian

2003-06-01

Technical, economic and environmental criteria were used to evaluate the feasibility of recycling plant nutrients in kitchen waste, human excreta and sullage from households in Phattalung (urban), Kuan Lang (peri urban) and Prik (rural) in Southern Thailand. The difference in situation and context of the three areas called for individual solutions, and for each area three sanitation systems were evaluated. However, in all three areas recycling human excreta and kitchen waste via composting latrines was found to be more environmental feasible than human excreta managed in septic tanks or sub surface trickle irrigation and kitchen waste disposed of at landfill sites or treated at composting plants. Sullage should in Kuan Lang and Prik be used directly on garden crops, but in Phattalung be treated in waste stabilisation ponds before discharge, to be environmentally feasible. The economic feasibility results varied among the three areas and among the involved stakeholders: farmers and Kuan Lang administration benefited from recycling waste, at the expense of other private users, Phattalung municipality and Prik municipality. The main cause of these conflicting interests was lack of cost recovery and public participation, which should therefore serve as the fundament of any future environmental and economic feasible sanitation system.

Technical feasibility of personalized articulating knee joint distraction for treatment of tibiofemoral osteoarthritis.

PubMed

Struik, T; Jaspers, J E N; Besselink, N J; van Roermund, P M; Plomp, S; Rudert, M J; Lafeber, F P J G; Mastbergen, S C

2017-11-01

Knee osteoarthritis is a highly prevalent degenerative joint disorder characterized by joint tissue damage and pain. Knee joint distraction has been introduced as a joint preserving surgical procedure to postpone knee arthroplasty. An often used standard externally fixation device for distraction poses a burden to patients due to the absence of joint flexion during the 6weeks treatment. Therefore, a personalized articulating distraction device was developed. The aim of this study was to test technical feasibility of this device. Based on an often applied rigid device, using equal bone pin positions and connectors, a hinge mechanism was developed consisting of a cam-following system for reproducing the complex joint-specific knee kinematics. In support, a device was developed for capturing the joint-specific sagittal plane articulation. The obtained kinematic data were translated into joint-specific cam shapes that were installed bilaterally in the hinge mechanism of the distraction device, as such providing personalized knee motion. Distraction of 5mm was performed within a range of motion of 30deg. joint flexion. Pre-clinical evaluation of the working principle was performed on human cadaveric legs and system stiffness characteristics were biomechanically evaluated. The desired range of motion was obtained and distraction was maintained under physiologically representative loading. Moreover, the joint-specific approach demonstrated tolerance of deviations from anatomical and alignment origin during initial placement of the developed distraction device. Articulation during knee distraction is considered technically feasible and has potential to decrease burden and improve acceptance of distraction therapy. Testing of clinical feasibility is warranted. Copyright © 2017 Elsevier Ltd. All rights reserved.

76 FR 18624 - Research, Technical Assistance and Training Programs: Notice of Final Circular

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-04

... to FTA Circular 6100.1D, Research and Technical Assistance Training Program: Application Instructions... DEPARTMENT OF TRANSPORTATION Federal Transit Administration Research, Technical Assistance and Training Programs: Notice of Final Circular AGENCY: Federal Transit Administration (FTA), DOT. ACTION...

Technical Feasibility Study of an Effective Low-Toxicity Obscurant Material

DTIC Science & Technology

2012-08-01

2. REPORT TYPE FINAL 3. DATES COVERED (From - To) 04/2011 – 07/2012 4 . TITLE AND SUBTITLE 5a. CONTRACT NUMBER W912HQ-11-C-0034 Technical...6 4 Work Package 3 – Laboratory-scale tests...chemistry to sea-salt aerosol. 4 The major component of sea-salt is sodium chloride. Sodium chloride can be very simply generated by the combustion

Off-road axle detection sensor (ORADS) : occlusion feasibility study, final technical report, 27 August, 1997.

DOT National Transportation Integrated Search

1997-08-27

The work accomplished under this initiative is in direct relation to the development effort proposed by Spectra : Research, Inc. (S*R) for an "Off-Road Axle Detection Sensor (ORADS)". The feasibility study was performed to : investigate potential occ...

Technical and Economic Feasibility Study of At-Grade Concrete Slab Track for Urban Rail Transit Systems

DOT National Transportation Integrated Search

1981-08-01

The report presents work conducted to evaluate the technical and economic feasibility of using concrete slab track systems for at-grade transit track. The functions of a rail transit track system are to guide railway vehicles and provide a safe and a...

National Alliance for Advanced Biofuels and Bio-Products Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olivares, Jose A.; Baxter, Ivan; Brown, Judith

2014-09-30

The main objective of NAABB was to combine science, technology, and engineering expertise from across the nation to break down critical technical barriers to commercialization of algae-based biofuels. The approach was to address technology development across the entire value chain of algal biofuels production, from selection of strains to cultivation, harvesting, extraction, fuel conversion, and agricultural coproduct production. Sustainable practices and financial feasibility assessments ununderscored the approach and drove the technology development.

AIMES Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Katz, Daniel S; Jha, Shantenu; Weissman, Jon

2017-01-31

This is the final technical report for the AIMES project. Many important advances in science and engineering are due to large-scale distributed computing. Notwithstanding this reliance, we are still learning how to design and deploy large-scale production Distributed Computing Infrastructures (DCI). This is evidenced by missing design principles for DCI, and an absence of generally acceptable and usable distributed computing abstractions. The AIMES project was conceived against this backdrop, following on the heels of a comprehensive survey of scientific distributed applications. AIMES laid the foundations to address the tripartite challenge of dynamic resource management, integrating information, and portable and interoperablemore » distributed applications. Four abstractions were defined and implemented: skeleton, resource bundle, pilot, and execution strategy. The four abstractions were implemented into software modules and then aggregated into the AIMES middleware. This middleware successfully integrates information across the application layer (skeletons) and resource layer (Bundles), derives a suitable execution strategy for the given skeleton and enacts its execution by means of pilots on one or more resources, depending on the application requirements, and resource availabilities and capabilities.« less

AIMES Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weissman, Jon; Katz, Dan; Jha, Shantenu

2017-01-31

This is the final technical report for the AIMES project. Many important advances in science and engineering are due to large scale distributed computing. Notwithstanding this reliance, we are still learning how to design and deploy large-scale production Distributed Computing Infrastructures (DCI). This is evidenced by missing design principles for DCI, and an absence of generally acceptable and usable distributed computing abstractions. The AIMES project was conceived against this backdrop, following on the heels of a comprehensive survey of scientific distributed applications. AIMES laid the foundations to address the tripartite challenge of dynamic resource management, integrating information, and portable andmore » interoperable distributed applications. Four abstractions were defined and implemented: skeleton, resource bundle, pilot, and execution strategy. The four abstractions were implemented into software modules and then aggregated into the AIMES middleware. This middleware successfully integrates information across the application layer (skeletons) and resource layer (Bundles), derives a suitable execution strategy for the given skeleton and enacts its execution by means of pilots on one or more resources, depending on the application requirements, and resource availabilities and capabilities.« less

Feasibility, efficacy, and predictive factors for the technical success of endoscopic nasogallbladder drainage: a prospective study.

PubMed

Yane, Kei; Maguchi, Hiroyuki; Katanuma, Akio; Takahashi, Kuniyuki; Osanai, Manabu; Kin, Toshifumi; Takaki, Ryo; Matsumoto, Kazuyuki; Gon, Katsushige; Matsumori, Tomoaki; Tomonari, Akiko; Nojima, Masanori

2015-03-01

Several studies have shown the useful-ness of endoscopic nasogallbladder drainage (ENGBD) in patients with acute cholecystitis. However, the procedure is difficult, and factors that affect technical success have not yet been clarified. We conducted a prospective study to eval-uate the technical feasibility, efficacy, and predictive factors for the technical success of ENGBD in patients with acute cholecystitis. All patients with moderate or severe acute cholecystitis who were enrolled underwent ENGBD between April 2009 and April 2011. Patients with surgically altered anatomy or pancreatobiliary malignancies were ex-cluded. The primary outcomes included technical success, clinical success, and complications. Factors that could affect the technical success were also examined. Of the 27 patients who underwent ENGBD during the study period, technical success was achieved in 21 (78%) and clinical improvement was achieved in 20 (95%). Early complications were encountered in four patients (15%). Gallbladder wall thickness (odds ratio [OR], 1.64; 95% confidence interval [CI], 1.08 to 2.47) and age (OR, 1.16; 95% CI, 1.00 to 1.35) were effective predictors of technical failure. ENGBD was effective in resolving acute cholecystitis; however, this modality was technically challenging and had a limited suc-cess rate. Because of technical difficulties, ENGBD should be reserved for limited indications. (Gut Liver, 2015;9239-246).

Technical and economic feasibility study of solar/fossil hybrid power systems

NASA Technical Reports Server (NTRS)

Bloomfield, H. S.; Calogeras, J. E.

1977-01-01

Results show that new hybrid systems utilizing fossil fuel augmentation of solar energy can provide significant capital and energy cost benefits when compared with solar thermal systems requiring thermal storage. These benefits accrue from a reduction of solar collection area that results from both the use of highly efficient gas and combined cycle energy conversion subsystems and elimination of the requirement for long-term energy storage subsystems. Technical feasibility and fuel savings benefits of solar hybrid retrofit to existing fossil-fired, gas and vapor cycle powerplants was confirmed; however, economic viability of steam cycle retrofit was found to be dependent on the thermodynamic and operational characteristics of the existing powerplant.

Final Technical Report- Virginia Solar Pathways Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bond, Katharine; Cosby, Sarah

This Report provides a technical review of the final results of a funding award to Virginia Electric and Power Company (Dominion Energy Virginia (DEV) or the Company) for a project under the U.S. Department of Energy’s Solar Energy Technologies Office. The three-year project was formally known as the Virginia Solar Pathways Project (VSPP or the Project). The purpose of the VSPP was to develop a collaborative utility-administered solar strategy (Solar Strategy) for DEV’s service territory in the Commonwealth that could serve as a replicable model for other states with similar policy environments.

The Independent Technical Analysis Process Final Report 2006-2007.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duberstein, Corey; Ham, Kenneth; Dauble, Dennis

2007-03-01

The Bonneville Power Administration (BPA) contracted with the Pacific Northwest National Laboratory (PNNL) to provide technical analytical support for system-wide fish passage information (BPA Project No. 2006-010-00). The goal of this project was to produce rigorous technical analysis products using independent analysts and anonymous peer reviewers. This project provided an independent technical source for non-routine fish passage analyses while allowing routine support functions to be performed by other well-qualified entities. The Independent Technical Analysis Process (ITAP) was created to provide non-routine analysis for fish and wildlife agencies and tribes in particular and the public in general on matters related tomore » juvenile and adult salmon and steelhead passage through the mainstem hydrosystem. The process was designed to maintain the independence of analysts and reviewers from parties requesting analyses, to avoid potential bias in technical products. The objectives identified for this project were to administer a rigorous, transparent process to deliver unbiased technical assistance necessary to coordinate recommendations for storage reservoir and river operations that avoid potential conflicts between anadromous and resident fish. Seven work elements, designated by numbered categories in the Pisces project tracking system, were created to define and accomplish project goals as follows: (1) 118 Coordination - Coordinate technical analysis and review process: (a) Retain expertise for analyst/reviewer roles. (b) Draft research directives. (c) Send directive to the analyst. (d) Coordinate two independent reviews of the draft report. (e) Ensure reviewer comments are addressed within the final report. (2) 162 Analyze/Interpret Data - Implement the independent aspects of the project. (3) 122 Provide Technical Review - Implement the review process for the analysts. (4) 132 Produce Annual Report - FY06 annual progress report with Pisces Disseminate (5

Joint Technical Architecture for Robotic Systems (JTARS)-Final Report

NASA Technical Reports Server (NTRS)

Bradley, Arthur T.; Holloway, Sidney E., III

2006-01-01

This document represents the final report for the Joint Technical Architecture for Robotic Systems (JTARS) project, funded by the Office of Exploration as part of the Intramural Call for Proposals of 2005. The project was prematurely terminated, without review, as part of an agency-wide realignment towards the development of a Crew Exploration Vehicle (CEV) and meeting the near-term goals of lunar exploration.

Site Operator technical report. Final report (1992--1996)

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-12-01

The Southern California Edison Company (SCE) and the US Department of Energy (DOE) entered into cooperative agreement No. DE-FC07-91ID13077 on August 23, 1991, which expired on August 3, 1996. This cooperative agreement provided SCE with DOE cofunding for participation in the DOE`s Electric and Hybrid Vehicle Site Operator Program. In return, SCE provided the DOE with quarterly progress reports which include operating and maintenance data for the electric (EVs) vehicles in SCE`s fleet. Herein is SCE`s final report for the 1992 to 1996 agreement period. As of September 1, 1996 the SCE fleet had 65 electric vehicles in service. Amore » total of 578,200 miles had been logged. During the agreement period, SCE sent the DOE a total of 19 technical reports (Appendix B). This report summarizes the technical achievements which took place during a long, productive and rewarding, relationship with the DOE.« less

Technical approach to groundwater restoration. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1993-11-01

The Technical Approach to Groundwater Restoration (TAGR) provides general technical guidance to implement the groundwater restoration phase of the Uranium Mill Tailings Remedial Action (UMTRA) Project. The TAGR includes a brief overview of the surface remediation and groundwater restoration phases of the UMTRA Project and describes the regulatory requirements, the National Environmental Policy Act (NEPA) process, and regulatory compliance. A section on program strategy discusses program optimization, the role of risk assessment, the observational approach, strategies for meeting groundwater cleanup standards, and remedial action decision-making. A section on data requirements for groundwater restoration evaluates the data quality objectives (DQO) andmore » minimum data required to implement the options and comply with the standards. A section on sits implementation explores the development of a conceptual site model, approaches to site characterization, development of remedial action alternatives, selection of the groundwater restoration method, and remedial design and implementation in the context of site-specific documentation in the site observational work plan (SOWP) and the remedial action plan (RAP). Finally, the TAGR elaborates on groundwater monitoring necessary to evaluate compliance with the groundwater cleanup standards and protection of human health and the environment, and outlines licensing procedures.« less

Technical Feasibility Study for Deployment of Ground-Source Heat Pump Systems: Portsmouth Naval Shipyard -- Kittery, Maine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hillesheim, M.; Mosey, G.

2014-11-01

The U.S. Environmental Protection Agency (EPA) Office of Solid Waste and Emergency Response, in accordance with the RE-Powering America's Lands initiative, engaged the U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to conduct feasibility studies to assess the viability of developing renewable energy generating facilities on contaminated sites. Portsmouth Naval Shipyard (PNSY) is a United States Navy facility located on a series of conjoined islands in the Piscataqua River between Kittery, ME and Portsmouth, NH. EPA engaged NREL to conduct a study to determine technical feasibility of deploying ground-source heat pump systems to help PNSY achieve energy reductionmore » goals.« less

Feasibility of geothermal space/water heating for Mammoth Lakes Village, California. Final report, September 1976--September 1977

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sims, A.V.; Racine, W.C.

1977-12-01

Results of a study to determine the technical, economic, and environmental feasibility of geothermal district heating for Mammoth Lakes Village, California are reported. The geothermal district heating system selected is technically feasible and will use existing technology in its design and operation. District heating can provide space and water heating energy for typical customers at lower cost than alternative sources of energy. If the district heating system is investor owned, lower costs are realized after five to six years of operation, and if owned by a nonprofit organization, after zero to three years. District heating offers lower costs than alternativesmore » much sooner in time if co-generation and/or DOE participation in system construction are included in the analysis. During a preliminary environmental assessment, no potential adverse environmental impacts could be identified of sufficient consequence to preclude the construction and operation of the proposed district heating system. A follow-on program aimed at implementing district heating in Mammoth is outlined.« less

Feasibility of commercial space manufacturing, production of pharmaceuticals. Volume 2: Technical analysis

NASA Technical Reports Server (NTRS)

1978-01-01

A technical analysis on the feasibility of commercial manufacturing of pharmaceuticals in space is presented. The method of obtaining pharmaceutical company involvement, laboratory results of the separation of serum proteins by the continuous flow electrophoresis process, the selection and study of candidate products, and their production requirements is described. The candidate products are antihemophilic factor, beta cells, erythropoietin, epidermal growth factor, alpha-1-antitrypsin and interferon. Production mass balances for antihemophelic factor, beta cells, and erythropoietin were compared for space versus ground operation. A conceptual description of a multiproduct processing system for space operation is discussed. Production requirements for epidermal growth factor of alpha-1-antitrypsin and interferon are presented.

Final Technical Report of Project DE-FG02-96ER14647

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lundeen, Stephen R.

This is the final technical report of work completed under DOE support over the period Sept. 1, 1996 until May 31, 2015. The title of the project was "Ion/Excited Atom Collision Studies with a Rydberg Target and a CO2 Laser" from 9/1/96 to 10/31/06, and "Properties of Actinide Ions from Measurements of Rydberg Ion Fine Structure" from 11/1/06 until 5/31/15. The primary technical results were a detailed experimental study of resonant charge transfer between Rydberg atoms and highly-charged ions, and unique measurements of many properties of multiply-charged Thorium ions.

"Type Ia Supernovae: Tools for Studying Dark Energy" Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Woosley, Stan; Kasen, Dan

2017-05-10

Final technical report for project "Type Ia Supernovae: Tools for the Study of Dark Energy" awarded jointly to scientists at the University of California, Santa Cruz and Berkeley, for computer modeling, theory and data analysis relevant to the use of Type Ia supernovae as standard candles for cosmology.

Development of Molten-Salt Heat Transfer Fluid Technology for Parabolic Trough Solar Power Plants - Public Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grogan, Dylan C. P.

2013-08-15

Executive Summary This Final Report for the "Development of Molten-Salt Heat Transfer Fluid (HTF) Technology for Parabolic Trough Solar Power Plants” describes the overall project accomplishments, results and conclusions. Phase 1 analyzed the feasibility, cost and performance of a parabolic trough solar power plant with a molten salt heat transfer fluid (HTF); researched and/or developed feasible component options, detailed cost estimates and workable operating procedures; and developed hourly performance models. As a result, a molten salt plant with 6 hours of storage was shown to reduce Thermal Energy Storage (TES) cost by 43.2%, solar field cost by 14.8%, and levelizedmore » cost of energy (LCOE) by 9.8% - 14.5% relative to a similar state-of-the-art baseline plant. The LCOE savings range met the project’s Go/No Go criteria of 10% LCOE reduction. Another primary focus of Phase 1 and 2 was risk mitigation. The large risk areas associated with a molten salt parabolic trough plant were addressed in both Phases, such as; HTF freeze prevention and recovery, collector components and piping connections, and complex component interactions. Phase 2 analyzed in more detail the technical and economic feasibility of a 140 MWe,gross molten-salt CSP plant with 6 hours of TES. Phase 2 accomplishments included developing technical solutions to the above mentioned risk areas, such as freeze protection/recovery, corrosion effects of applicable molten salts, collector design improvements for molten salt, and developing plant operating strategies for maximized plant performance and freeze risk mitigation. Phase 2 accomplishments also included developing and thoroughly analyzing a molten salt, Parabolic Trough power plant performance model, in order to achieve the project cost and performance targets. The plant performance model and an extensive basic Engineering, Procurement, and Construction (EPC) quote were used to calculate a real levelized cost of energy (LCOE) of 11.50�

Final Technical Report, Wind Generator Project (Ann Arbor)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Geisler, Nathan

A Final Technical Report (57 pages) describing educational exhibits and devices focused on wind energy, and related outreach activities and programs. Project partnership includes the City of Ann Arbor, MI and the Ann Arbor Hands-on Museum, along with additional sub-recipients, and U.S. Department of Energy/Office of Energy Efficiency and Renewable Energy (EERE). Report relays key milestones and sub-tasks as well as numerous graphics and images of five (5) transportable wind energy demonstration devices and five (5) wind energy exhibits designed and constructed between 2014 and 2016 for transport and use by the Ann Arbor Hands-on Museum.

Iowa Hill Pumped Storage Project Investigations - Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hanson, David

2016-07-01

This Final Technical Report is a summary of the activities and outcome of the Department of Energy (DOE) Assistance Agreement DE-EE0005414 with the Sacramento Municipal Utility District (SMUD). The Assistance Agreement was created in 2012 to support investigations into the Iowa Hill Pumped-storage Project (Project), a new development that would add an additional 400 MW of capacity to SMUD’s existing 688MW Upper American River Hydroelectric Project (UARP) in the Sierra Nevada mountains east of Sacramento, California.

Admiralty Inlet Pilot Tidal Project Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Collar, Craig

This document represents the final report for the Admiralty Inlet Pilot Tidal Project, located in Puget Sound, Washington, United States. The Project purpose was to license, permit, and install a grid-connected deep-water tidal turbine array (two turbines) to be used as a platform to gather operational and environmental data on tidal energy generation. The data could then be used to better inform the viability of commercial tidal energy generation from technical, economic, social, and environmental standpoints. This data would serve as a critical step towards the responsible advancement of commercial scale tidal energy in the United States and around themore » world. In late 2014, Project activities were discontinued due to escalating costs, and the DOE award was terminated in early 2015. Permitting, licensing, and engineering design activities were completed under this award. Final design, deployment, operation, and monitoring were not completed. This report discusses the results and accomplishments achieved under the subject award.« less

PITTSBURGH TECHNICAL HEALTH TRAINING INSTITUTE DEMONSTRATION PROJECT. FINAL REPORT, VOLUME II.

ERIC Educational Resources Information Center

KISHKUNAS, LOUIS J.

APPENDIXES TO THE "FINAL REPORT," VOLUME I (VT 005 511), ARE INCLUDED--(1) A SCHEMATIC REPRESENTATION OF CURRICULUM DEVELOPMENT, (2) TECHNICAL BEHAVIOR CHECKLISTS, (3) PERFORMANCE INVENTORY FORMS USED IN ON-THE-JOB OBSERVATIONS, (4) REPORT FORM FOR TYPICAL JOB BEHAVIOR OF EMPLOYEE, (5) COOPERATING AREA HEALTH INSTITUTIONS, (6) TABLES OF Z SCORES…

STTR Phase 1 Final Technical Report for Project Entitled "Developing a Mobile Torrefaction Machine"

DOE Office of Scientific and Technical Information (OSTI.GOV)

James, Joseph J.

The goal of this project, sponsored by Agri-Tech Producers, LLC (ATP), the small business grantee, was to determine if the torrefaction technology, developed by North Carolina State University (NCSU), which ATP has licensed, could be feasibly deployed in a mobile unit. The study adds to the area investigated, by having ATP’s STTR Phase I team give thoughtful consideration to how to use NCSU’s technology in a mobile unit. The findings by ATP’s team were that NCSU’s technology would best perform in units 30’ by 80’ (See Spec Sheet for the Torre-Tech 5.0 Unit in the Appendix) and the technical effectivenessmore » and economic feasibility investigation suggested that such units were not easily, efficiently or safely utilized in a forest or farm setting. (Note rendering of possible mobile system in the Appendix) Therefore, the findings by ATP’s team were that NCSU’s technology could not feasibly be deployed as a mobile unit.« less

Feasibility study of solid surface subreflector production techniques

NASA Technical Reports Server (NTRS)

1982-01-01

The principal effort was to study technical feasibility and cost aspects of the production technique of spin forming a subreflector reflective surface to a desired surface of revolution, back the surface with fiberglass to stabilize it sufficiently so that it may be machined to the target surface tolerance of .008 inches Root Mean Square (RMS) with a goal of .003 inches RMS. To verify this production technique, analyses was performed to define the production procedure. A price estimate for a 150 inch diameter subreflector for a 34 meter cassegrain antenna. During this feasibility study, numerous production processes were evaluated theoretically as production approaches for single surface, non-welded subreflectors. The first successful was the principal process of spin forming the reflective surface, backing with fiberglass and machining to a final contour. The second successful process was spin forming or bump forming a thicker reflective surface, with an integral (welded in) structure as a backing and machining the mounting pads and reflector to a final configuration.

Metastatic renal cell carcinoma: CT-guided immunotherapy as a technically feasible and safe approach to delivery of gene therapy for treatment.

PubMed

Suh, Robert D; Goldin, Jonathan G; Wallace, Amanda B; Sheehan, Ramon E; Heinze, Stefan B; Gitlitz, Barbara J; Figlin, Robert A

2004-05-01

To assess the technical feasibility and safety of weekly outpatient percutaneous computed tomographic (CT)-guided intratumoral injections of interleukin-2 (IL-2) plasmid DNA in a wide variety of superficial and deep tumor sites. Twenty-nine patients with metastatic renal cell carcinoma and a total of 30 lesions measuring 1.0 cm(2) or greater in accessible thoracic (n = 15) or abdominal (n = 15) locations underwent up to three cycles of six weekly intratumoral IL-2 plasmid DNA injections. CT was used to guide needle placement and injection. After injection cycle 1, patients whose tumors demonstrated stable (< or =25% increase and < or =50% decrease in product of lesion diameters) or decreased size (>50% decrease in product of lesion diameters) advanced to injection cycle 2. Patients whose lesions decreased in size by more than 50% over the course of injection cycle 2 were eligible to begin injection cycle 3. An acceptable safety and technical feasibility profile for this technique was deemed to be (a) a safety and feasibility profile similar to that of single-needle biopsy and (b) an absence of serious adverse events (as defined in Title 21 of the Code of Federal Regulations) and/or unacceptable toxicities (as graded according to the National Cancer Institute Common Toxicity Criteria). A total of 284 intratumoral injections were performed, with a mean of 9.8 injections (range, 6-18 injections) received by each patient. Technical success (needle placement and injection of gene therapy agent) was achieved in all cases. Complications were experienced after 42 (14.8%) of the 284 injections. The most common complication was pneumothorax (at 32 [28.6%] of 112 intrathoracic injections), for which only one patient required catheter drainage. Complications occurred randomly throughout injection cycles and did not appear to increase as patients received more injections (P =.532). No patient experienced serious adverse events or unacceptable toxicities. Percutaneous CT

Ultrasound-Guided Intermediate Site Greater Occipital Nerve Infiltration: A Technical Feasibility Study.

PubMed

Zipfel, Jonathan; Kastler, Adrian; Tatu, Laurent; Behr, Julien; Kechidi, Rachid; Kastler, Bruno

2016-01-01

Two studies recently reported that computed tomography (CT) guided infiltration of the greater occipital nerve at its intermediate site allows a high efficacy rate with long-lasting pain relief following procedure in occipital neuralgia and in various craniofacial pain syndromes. The purpose of our study was to evaluate the technical feasibility and safety of ultrasound-guided intermediate site greater occipital nerve infiltration. Retrospective study. This study was conducted at the imaging department of a 1,409 bed university hospital. Local institutional review board approval was obtained and written consent was waived. In this retrospective study, 12 patients suffering from refractory occipital neuralgia or craniofacial pain syndromes were included between April and October 2014. They underwent a total of 21 ultrasound-guided infiltrations. Infiltration of the greater occipital nerve was performed at the intermediate site of the greater occipital nerve, at its first bend between obliqus capitis inferior and semispinalis capitis muscles with local anestetics and cortivazol. Technical success was defined as satisfactory diffusion of added iodinated contrast media in the fatty space between these muscles depicted on control CT scan. We also reported first data of immediate block test efficacy and initial clinical efficacy at 7 days, one month, and 3 months, defined by a decrease of at least 50% of visual analog scale (VAS) scores. Technical success rate was 95.24%. Patients suffered from right unilateral occipital neuralgia in 3 cases, left unilateral occipital neuralgia in 2 cases, bilateral occipital neuralgia in 2 cases, migraine in one case, cervicogenic headache in one case, tension-type headache in 2 cases, and cluster headache in one case. Block test efficacy was found in 93.3% (14/15) cases. Clinical efficacy was found in 80% of cases at 7 days, in 66.7% of cases at one month and in 60% of cases at 3 months. No major complications were noted. Some of the

77 FR 30512 - Native American Career and Technical Education Program; Final Waivers and Extension of Project...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-23

... DEPARTMENT OF EDUCATION Native American Career and Technical Education Program; Final Waivers and... American Career and Technical Education Program Catalog of Federal Domestic Assistance (CFDA) Number: 84.101A. SUMMARY: For 60-month projects funded in fiscal year (FY) 2007 under the Native American Career...

Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brizard, Alain J

Final Technical Report for U.S. Department of Energy Grant No. DE-FG02-09ER55005 Nonlinear FLR Effects in Reduced Fluid Models Alain J. Brizard, Saint Michael's College The above-mentioned DoE grant was used to support research activities by the PI during a sabbatical leave from Saint Michael's College in 2009. The major focus of the work was the role played by guiding-center and gyrocenter (linear and nonlinear) polarization and magnetization effects in understanding transport processes in turbulent magnetized plasmas. The theoretical tools used for this work include Lie-transform perturbation methods and Lagrangian (variational) methods developed by the PI in previous work. The presentmore » final technical report lists (I) the peer-reviewed publications that were written based on work funded by the Grant; (II) invited and contributed conference presentations during the period funded by the Grant; and (III) seminars presented during the period funded by the Grant. I. Peer-reviewed Publications A.J. Brizard and N. Tronko, 2011, Exact momentum conservation for the gyrokinetic Vlasov- Poisson equations, Physics of Plasmas 18 , 082307:1-14 [http://dx.doi.org/10.1063/1.3625554 ]. J. Decker, Y. Peysson, A.J. Brizard, and F.-X. Duthoit, 2010, Orbit-averaged guiding-center Fokker-Planck operator for numerical applications, Physics of Plasmas 17, 112513:1-12 [http://dx.doi.org/10.1063/1.3519514]. A.J. Brizard, 2010, Noether derivation of exact conservation laws for dissipationless reduced fluid models, Physics of Plasmas 17, 112503:1-8 [http://dx.doi.org/10.1063/1.3515303]. F.-X. Duthoit, A.J. Brizard, Y. Peysson, and J. Decker, 2010, Perturbation analysis of trapped particle dynamics in axisymmetric dipole geometry, Physics of Plasmas 17, 102903:1-9 [http://dx.doi.org/10.1063/1.3486554]. A.J. Brizard, 2010, Exact energy conservation laws for full and truncated nonlinear gyrokinetic equations, Physics of Plasmas 17, 042303:1-11 [http://dx.doi.org/10.1063/1.3374428]. A

32 CFR 37.895 - How is the final performance report to be sent to the Defense Technical Information Center?

Code of Federal Regulations, 2014 CFR

2014-07-01

... How is the final performance report to be sent to the Defense Technical Information Center? (a... 32 National Defense 1 2014-07-01 2014-07-01 false How is the final performance report to be sent to the Defense Technical Information Center? 37.895 Section 37.895 National Defense Department of...

32 CFR 37.895 - How is the final performance report to be sent to the Defense Technical Information Center?

Code of Federal Regulations, 2011 CFR

2011-07-01

... How is the final performance report to be sent to the Defense Technical Information Center? (a... 32 National Defense 1 2011-07-01 2011-07-01 false How is the final performance report to be sent to the Defense Technical Information Center? 37.895 Section 37.895 National Defense Department of...

32 CFR 37.895 - How is the final performance report to be sent to the Defense Technical Information Center?

Code of Federal Regulations, 2013 CFR

2013-07-01

... How is the final performance report to be sent to the Defense Technical Information Center? (a... 32 National Defense 1 2013-07-01 2013-07-01 false How is the final performance report to be sent to the Defense Technical Information Center? 37.895 Section 37.895 National Defense Department of...

32 CFR 37.895 - How is the final performance report to be sent to the Defense Technical Information Center?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 1 2012-07-01 2012-07-01 false How is the final performance report to be sent to the Defense Technical Information Center? 37.895 Section 37.895 National Defense Department of... How is the final performance report to be sent to the Defense Technical Information Center? (a...

Jefferson Proving Ground, South of the Fining Line, Final Remedial Investigation/Feasibility Study, Resource Management Plan

DTIC Science & Technology

1993-01-01

and various DOD sites. I From 1984 to 1987, Mr. Pincock was a Certified Radiation and Chemistry Technician for United Nuclear Industries. He performed...in 1983, Mr. Pincock assisted the senior technical staff in radiation protection as a Junior Health Physics Technician at the Nuclear Support Services...SCOPE OF PROGRAM This plan contains a description of the personnel and procedures for managing the Remedial Investigation/Feasibility Study (RI/FS) at

Low/medium-Btu coal-gasification feasibility study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-11-01

This study examines the feasibility of applying the concepts of Coal Gasification and Combined Cycle Technology to the re-powering of existing steam turbine-electric generating facilities. The primary objectives of this study include: (1) the determination of the feasibility of designing a technically sound system embodying this technology; (2) the determination of the potential for displacing foreign oil by the project; (3) the identificaton of any constraints and/or barriers that might impede the accomplishment of such a project; and (4) the evaluation of the potential benefits of such a system. Although the system is designed around the use of commercially available,more » state-of-the-art components and equipment, a completely integrated, electric generating plant, such as is being proposed here, has not yet been demonstrated. However, the designs developed as part of this study combine these components, utilizing well developed and technically sound concepts in such a way as to provide a reasonable degree of confidence in the workability of the total system. This study offers the potential for reducing oil dependency; the possibility of improving cycle efficiency and extending the useful life of existing facilities; the feasibility of re-vitalizing a facility located within a major load center; and presents some attractive possibilities for a co-generation, district heating application in the central portions of Bridgeport. Although the results of the study produce a number of clear conclusions, they also stimulate additional questions, the resolution of which would require further study and more detailed design. The final resolution of these questions that still remain may have a significant effect on the final conclusions concerning the viability of this project, and it is for this reason that further study is required.« less

Solar Heating and Cooling of Buildings: Phase 0. Feasibility and Planning Study. Volume 1: Executive Summary. Document No. 74SD419. Final Report.

ERIC Educational Resources Information Center

General Electric Co., Philadelphia, PA. Space Div.

The purpose of this study was to establish the technical and economic feasibility of using solar energy for the heating and cooling of buildings and to provide baseline information for the widespread application of solar energy. The initial step in this program was a study of the technical, economic, societal, legal, and environmental factors…

Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eggeman, Tim; O'Neill, Brian

2016-08-17

ZeaChem Inc. and US DOE successfully demonstrated the ZeaChem process for producing sugars and ethanol from high-impact biomass feedstocks. The project was executed over a 5-year period under a $31.25 million cooperative agreement (80:20 Federal:ZeaChem cost share). The project was managed by dividing it into three budget periods. Activities during Budget Period 1 were limited to planning, permitting, and other pre-construction planning. Budget Period 2 activities included engineering, procurement, construction, commissioning, start-up and initial operations through the Independent Engineer Test Runs. The scope of construction was limited to the Chem Frac and Hydrogenolysis units, as the Core Facility was alreadymore » in place. Construction was complete in December 2012, and the first cellulosic ethanol was produced in February 2013. Additional operational test runs were conducted during Budget Period 3 (completed June 2015) using hybrid poplar, corn stover, and wheat straw feedstocks, resulting in the production of cellulosic ethanol and various other biorefinery intermediates. The research adds to the understanding of the Chem Frac and Hydrogenolysis technologies in that the technical performance of each unit was measured, and the resulting data and operational experience can be used as the basis for engineering designs, thus mitigating risks for deployment in future commercial facilities. The Chem Frac unit was initially designed to be operated as two-stage dilute acid hydrolysis, with first stage conditions selected to remove the hemicellulose fraction of the feedstock, and the second stage conditions selected to remove the cellulose fraction. While the Chem Frac unit met or exceeded the design capacity of 10 ton(dry)/day, the technical effectiveness of the Chem Frac unit was below expectations in its initial two-stage dilute acid configuration. The sugars yields were low, the sugars were dilute, and the sugars had poor fermentability caused by excessive

Dual-Mission Large Aircraft Feasibility Study and Aerodynamic Investigation

NASA Technical Reports Server (NTRS)

Mavris, Dimitri

1997-01-01

A Dual-Mission Large Aircraft, or DMLA, represents the possibility of a single aircraft capable of fulfilling both a Global Reach Aircraft (GRA) and Very Large Transport (VLT) roles. The DMLA, by combining the GRA and VLT into a single new aircraft, could possibly lower the aircraft manufacturer's production costs through the resulting increase in production quantity. This translates into lower aircraft acquisition costs, a primary concern for both the Air Force and commercial airlines. This report outlines the first steps taken in this study, namely the assessment of technical and economic feasibility of the DMLA concept. In the course of this project, specialized GRA and VLT aircraft were sized for their respective missions, using baseline conventional (i.e., lacking advanced enabling technologies) aircraft models from previous work for the Air Force's Wright Laboratory and NASA-Langley. DMLA baseline aircraft were then also developed, by first sizing the aircraft for the more critical of the two missions and then analyzing the aircraft's performance over the other mission. The resulting aircraft performance values were then compared to assess technical feasibility. Finally, the life-cycle costs of each aircraft (GRA, VLT, and DMLA) were analyzed to quantify economic feasibility. These steps were applied to both a two-engine aircraft set, and a four-engine aircraft set.

District heating and cooling feasibility study, Dunkirk, New York

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The objective of this project is to perform a preliminary investigation of the technical and economic feasibility of implementing a district heating and cooling (DHC) system in the City of Dunkirk, New York. The study was conducted by first defining a heating and cooling (HC) load service area. Then, questionnaires were sent to prospective DHC customers. After reviewing the owners responses, large consumers of energy were interviewed for more detail of their HC systems, including site visits, to determine possibilities of retrofitting their systems to district heating and cooling. Peak HC loads for the buildings were estimated by Burns andmore » Roe's in-house computer programs. Based on the peak loads, certain customers were determined for suitability as anchor customers. Various options using cogeneration were investigated for possible HC sources. Equipment for HC sources and HC loads were sized and their associated costs estimated. Finally, economic analyses were performed. The conclusion is that it is technically and economically feasible to implement a district heating and cooling system in the City of Dunkirk. 14 figs., 15 tabs.« less

Technical Report Cellulosic Based Black Liquor Gasification and Fuels Plant Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fornetti, Micheal; Freeman, Douglas

2012-10-31

The Cellulosic Based Black Liquor Gasification and Fuels Plant Project was developed to construct a black liquor to Methanol biorefinery in Escanaba, Michigan. The biorefinery was to be co-located at the existing pulp and paper mill, NewPage’s Escanaba Paper Mill and when in full operation would: • Generate renewable energy for Escanaba Paper Mill • Produce Methanol for transportation fuel of further refinement to Dimethyl Ether • Convert black liquor to white liquor for pulping. Black liquor is a byproduct of the pulping process and as such is generated from abundant and renewable lignocellulosic biomass. The biorefinery would serve tomore » validate the thermochemical pathway and economic models for black liquor gasification. It was a project goal to create a compelling new business model for the pulp and paper industry, and support the nation’s goal for increasing renewable fuels production and reducing its dependence on foreign oil. NewPage Corporation planned to replicate this facility at other NewPage Corporation mills after this first demonstration scale plant was operational and had proven technical and economic feasibility. An overview of the process begins with black liquor being generated in a traditional Kraft pulping process. The black liquor would then be gasified to produce synthesis gas, sodium carbonate and hydrogen sulfide. The synthesis gas is then cleaned with hydrogen sulfide and carbon dioxide removed, and fed into a Methanol reactor where the liquid product is made. The hydrogen sulfide is converted into polysulfide for use in the Kraft pulping process. Polysulfide is a known additive to the Kraft process that increases pulp yield. The sodium carbonate salts are converted to caustic soda in a traditional recausticizing process. The caustic soda is then part of the white liquor that is used in the Kraft pulping process. Cellulosic Based Black Liquor Gasification and Fuels Plant project set out to prove that black liquor

Achieving Hydrogen Storage Goals through High-Strength Fiber Glass - Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Hong; Johnson, Kenneth I.; Newhouse, Norman L.

Led by PPG and partnered with Hexagon Lincoln and Pacific Northwest National Laboratory (PNNL), the team recently carried out a project “Achieving Hydrogen Storage Goals through High-Strength Fiber Glass”. The project was funded by DOE’s Fuel Cell Technologies office within the Office of Energy Efficiency and Renewable Energy, starting on September 1, 2014 as a two-year project to assess technical and commercial feasibilities of manufacturing low-cost, high-strength glass fibers to replace T700 carbon fibers with a goal of reducing the composite total cost by 50% of the existing, commercial 700 bar hydrogen storage tanks used in personal vehicles.

Feasibility of Developing a Protocol for Automated Protist Analysis

DTIC Science & Technology

2010-03-01

Acquisition Directorate Research & Development Center Report No: CG-D-02-ll Feasibility of Developing a Protocol for Automated Protist Analysis...Technical Information Service, Springfield, VA 22161. March 2010 Homeland Security Feasibility of Developing a Protocol for Automated Protist ...March 21)10 Feasibility of Developing a Protocol for Automated Protist Analysis 00 00 o CM Technical Report Documentation Page 1. Report No CG-D

Feasibility Demonstration of Exciplex Fluorescence Measurements in Evaporating Laminar Sprays of Diesel Fuel

DTIC Science & Technology

2011-05-15

code) 1 FEASIBILITY DEMONSTRATION OF EXCIPLEX FLUORESCENCE MEASUREMENTS IN EVAPORATING LAMINAR SPRAYS OF DIESEL FUEL Final Technical Report Grant...fluorescence is found to increase with temperature up to 538 K and then declines. Fluorescence from the liquid phase, i.e. the exciplex (Naphthalene+TMPD...to have as well characterized a description of the spray environment and assess conclusively the potential of the exciplex approach for more

Air Quality Modeling Technical Support Document for the Final Cross State Air Pollution Rule Update

EPA Pesticide Factsheets

In this technical support document (TSD) we describe the air quality modeling performed to support the final Cross State Air Pollution Rule for the 2008 ozone National Ambient Air Quality Standards (NAAQS).

Pacific Educational Computer Network Study. Final Report.

ERIC Educational Resources Information Center

Hawaii Univ., Honolulu. ALOHA System.

The Pacific Educational Computer Network Feasibility Study examined technical and non-technical aspects of the formation of an international Pacific Area computer network for higher education. The technical study covered the assessment of the feasibility of a packet-switched satellite and radio ground distribution network for data transmission…

77 FR 30514 - Native Hawaiian Career and Technical Education Program; Final Waiver and Extension of Project Period

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-23

... DEPARTMENT OF EDUCATION Native Hawaiian Career and Technical Education Program; Final Waiver and.... ACTION: Notice. Overview Information Final Waiver and Extension of Project Period for the Native Hawaiian.... SUMMARY: For 36-month projects funded in fiscal year (FY) 2009 under the Native Hawaiian Career and...

Evaluation of Routine Atmospheric Sounding Measurements using Unmanned Systems (ERASMUS): Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

de Boer, Gijs; Lawrence, Dale; Palo, Scott

2017-03-29

This final technical report details activities undertaken as part of the referenced project. Included is information on the preparation of aircraft for deployment to Alaska, summaries of the three deployments covered under this project, and a brief description of the dataset and science directions pursued. Additionally, we provide information on lessons learned, publications, and presentations resulting from this work.

Final Technical Report for contract number DE-FG02-05ER15670

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glazebrook, Jane

This is the final technical report for contract number DE-FG02-05ER15670. The project is now complete, and results of the project have been published. Two papers were published based on work done in the last three-year funding period. The DOIs of these papers are included below. The abstracts of the papers, providing summaries of the work, are included in the body of the report.

Feasiblity study for a 34 GHz (Ka band) gyroamplifier

NASA Technical Reports Server (NTRS)

Stone, D. S.; Bier, R. E.; Caplan, M.; Huey, H. E.; Pirkle, D. R.; Robinson, J. D.; Thompson, L.

1984-01-01

The feasibility of using a gyroklystron power tube as the final amplifier in a 400 kW CW 34 GHz transmitter on the Goldstone Antenna is investigated. A conceptual design of the gyroklystron and the transmission line connecting it with the antenna feed horn is presented. The performance characteristics of the tube and transmission line are compared to the transmitter requirements for a deep space radar system. Areas of technical risk for a follow-on hardware development program for the gyroklystron amplifier and overmoded transmission line components are discussed.

Beowawe Bottoming Binary Unit - Final Technical Report for EE0002856

DOE Office of Scientific and Technical Information (OSTI.GOV)

McDonald, Dale Edward

2013-02-12

This binary plant is the first high-output refrigeration based waste heat recovery cycle in the industry. Its working fluid is environmentally friendly and as such, the permits that would be required with a butane based cycle are not necessary. The unit is modularized, meaning that the unit’s individual skids were assembled in another location and were shipped via truck to the plant site. This project proves the technical feasibility of using low temperature brine The development of the unit led to the realization of low temperature, high output, and environmentally friendly heat recovery systems through domestic research and engineering. Themore » project generates additional renewable energy for Nevada, resulting in cleaner air and reduced carbon dioxide emissions. Royalty and tax payments to governmental agencies will increase, resulting in reduced financial pressure on local entities. The major components of the unit were sourced from American companies, resulting in increased economic activity throughout the country.« less

Making fired bricks with spent equilibrium catalyst-a technical feasibility study

USGS Publications Warehouse

Chou, M.-L.; Chen, L.-M.; Lai, Y.-C.; Chou, S.-F.

2009-01-01

Fluid catalytic cracking in an oil refinery uses a catalyst, such as an alumino-silicate zeolite, in the conversion of heavy hydrocarbons to light hydrocarbons. A small fraction of the catalyst is continually replaced with fresh catalyst to maintain activity. In North America, more than 400 tons of spent alumino-silicate equilibrium catalyst (spent e-cat), and worldwide, more than 1,100 tons, are generated daily, most of which is disposed of in landfills (municipal and on-site facilities). In this study, three spent e-cat samples were tested in a value-added application that would utilize this waste in the manufacturing of fired bricks. The results of this study indicate that spent e-cat is a technically feasible raw material substitute for the clay and shale commonly used in fired brick production. Fired bricks produced with up to 30 wt% of spent e-cat showed good physical appearance and their water absorption properties met the ASTM C 62 specifications for building bricks of either the moderate-or severe-weathering grade.

A Process Evaluation of Project Developmental Continuity: Final Report of the PDC Feasibility Study, 1974-1977.

ERIC Educational Resources Information Center

Love, John M.; And Others

This is the final report of the 3-year feasibility phase of a projected 7-year longitudinal evaluation of Project Developmental Continuity (PDC), a Head Start demonstration program aimed at providing educational and developmental continuity between children's Head Start and primary school experiences. Chapter I gives an overview of the PDC program…

BBN technical memorandum W1291 infrasound model feasibility study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farrell, T., BBN Systems and Technologies

1998-05-01

The purpose of this study is to determine the need and level of effort required to add existing atmospheric databases and infrasound propagation models to the DOE`s Hydroacoustic Coverage Assessment Model (HydroCAM) [1,2]. The rationale for the study is that the performance of the infrasound monitoring network will be an important factor for both the International Monitoring System (IMS) and US national monitoring capability. Many of the technical issues affecting the design and performance of the infrasound network are directly related to the variability of the atmosphere and the corresponding uncertainties in infrasound propagation. It is clear that the studymore » of these issues will be enhanced by the availability of software tools for easy manipulation and interfacing of various atmospheric databases and infrasound propagation models. In addition, since there are many similarities between propagation in the oceans and in the atmosphere, it is anticipated that much of the software infrastructure developed for hydroacoustic database manipulation and propagation modeling in HydroCAM will be directly extendible to an infrasound capability. The study approach was to talk to the acknowledged domain experts in the infrasound monitoring area to determine: 1. The major technical issues affecting infrasound monitoring network performance. 2. The need for an atmospheric database/infrasound propagation modeling capability similar to HydroCAM. 3. The state of existing infrasound propagation codes and atmospheric databases. 4. A recommended approach for developing the required capabilities. A list of the people who contributed information to this study is provided in Table 1. We also relied on our knowledge of oceanographic and meteorological data sources to determine the availability of atmospheric databases and the feasibility of incorporating this information into the existing HydroCAM geographic database software. This report presents a summary of the need for an

Final Technical Report, City of Brockton Solar Brightfield: Deploying a Solar Array on a Brockton Brownfield

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ribeiro, Lori

The City of Brockton, Massachusetts sought to install New England’s largest solar array at a remediated brownfield site on Grove Street. The 425-kilowatt solar photovoltaic array – or “Brightfield” – was installed in an urban park setting along with interpretive displays to maximize the educational opportunities. The “Brightfield” project included 1,395 310-Watt solar panels connected in “strings” that span the otherwise unusable 3.7-acre site. The project demonstrated that it is both technically and economically feasible to install utility scale solar photovoltaics on a capped landfill site. The US Department of Energy conceived the Brightfields program in 2000, and Brockton’s Brightfieldmore » is the largest such installation nationwide. Brockton’s project demonstrated that while it was both technically and economically feasible to perform such a project, the implementation was extremely challenging due to the state policy barriers, difficulty obtaining grant funding, and level of sophistication required to perform the financing and secure required state approvals. This demonstration project can be used as a model for other communities that wish to implement “Brownfields to Brightfields” projects; 2) implementing utility scale solar creates economies of scale that can help to decrease costs of photovoltaics; 3) the project is an aesthetic, environmental, educational and economic asset for the City of Brockton.« less

SafeConnect Solar - Final Scientific/Technical Report (Updated)

DOE Office of Scientific and Technical Information (OSTI.GOV)

McNish, Zachary

2016-02-03

Final Scientific/Technical Report from Tier 0 SunShot Incubator award for hardware-based solution to reducing soft costs of installed solar. The primary objective of this project was for SafeConnect Solar (“SafeConnect”) to create working proof-of-concept hardware prototypes from its proprietary intellectual property and business concepts for a plug-and-play, safety-oriented hardware solution for photovoltaic solar systems. Specifically, SafeConnect sought to build prototypes of its “SmartBox” and related cabling and connectors, as well as the firmware needed to run the hardware. This hardware is designed to ensure a residential PV system installed with it can address all safety concerns that currently form themore » basis of AHJ electrical permitting and licensing requirements, thereby reducing the amount of permitting and specialized labor required on a residential PV system, and also opening up new sales channels and customer acquisition opportunities.« less

Final Technical Report - Center for Technology for Advanced Scientific Component Software (TASCS)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sussman, Alan

2014-10-21

This is a final technical report for the University of Maryland work in the SciDAC Center for Technology for Advanced Scientific Component Software (TASCS). The Maryland work focused on software tools for coupling parallel software components built using the Common Component Architecture (CCA) APIs. Those tools are based on the Maryland InterComm software framework that has been used in multiple computational science applications to build large-scale simulations of complex physical systems that employ multiple separately developed codes.

Final Technical Report for DE-FG02-98ER45737

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ade, Harald W.

This document represents the cumulative, final technical report for Grant No. DE-FG02- 98ER45737, the title of which has changed with each funding period, but the research pursued is within a coherent overall theme of methods and technique developments that exploit contrast at the carbon absorption edge to characterize complex organic materials and the use of these synchrotron radiation-based methods for important research challenges in polymer physics and Materials Science. The last three funding periods focused on organic devices and in particular organic solar cells (OSCs), owing to their extra-ordinarily complex morphology, yet high potential as a cheap and printable power-conversionmore » technology.« less

Community College Technical Mathematics Project. Final Report.

ERIC Educational Resources Information Center

Self, Samuel L.

The purpose of the research project was to develop an applied or technical mathematics curriculum which would meet the needs of vocational-technical students at the community college level. The research project was divided into three distinct phases: Identifying the mathematical concepts requisite for job-entry competencies in each of the…

Early assessment of feasibility and technical specificities of transoral robotic surgery using the da Vinci Xi.

PubMed

Gorphe, Philippe; Von Tan, Jean; El Bedoui, Sophie; Hartl, Dana M; Auperin, Anne; Qassemyar, Quentin; Moya-Plana, Antoine; Janot, François; Julieron, Morbize; Temam, Stephane

2017-12-01

The latest generation Da Vinci ® Xi™ Surgical System Robot released has not been evaluated to date in transoral surgery for head and neck cancers. We report here the 1-year results of a non-randomized phase II multicentric prospective trial aimed at assessing its feasibility and technical specificities. Our primary objective was to evaluate the feasibility of transoral robotic surgery using the da Vinci ® Xi™ Surgical System Robot. The secondary objective was to assess peroperative outcomes. Twenty-seven patients, mean age 62.7 years, were included between May 2015 and June 2016 with tumors affecting the following sites: oropharynx (n = 21), larynx (n = 4), hypopharynx (n = 1), parapharyngeal space (n = 1). Eighteen patients were included for primary treatment, three for a local recurrence, and six for cancer in a previously irradiated field. Three were reconstructed with a FAMM flap and 6 with a free ALT flap. The mean docking time was 12 min. "Chopsticking" of surgical instruments was very rare. During hospitalization following surgery, 3 patients experienced significant bleeding between day 8 and 9 that required surgical transoral hemostasis (n = 1) or endovascular embolization (n = 2). Transoral robotic surgery using the da Vinci ® Xi™ Surgical System Robot proved feasible with technological improvements compared to previous generation surgical system robots and with a similar postoperative course. Further technological progress is expected to be of significant benefit to the patients.

76 FR 50202 - National Technical Assistance and Dissemination Center for Children Who Are Deaf-Blind; Final...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-12

... DEPARTMENT OF EDUCATION [CFDA No. 84.326T] National Technical Assistance and Dissemination Center for Children Who Are Deaf-Blind; Final Extension of Project Period and Waiver AGENCY: Office of Special Education Programs, Office of Special Education and Rehabilitative Services, Department of...

Direct Final Rule: Nonroad Diesel Technical Amendments and Tier 3 Technical Relief Provision

EPA Pesticide Factsheets

Rule making certain technical corrections to the rules establishing emission standards for nonroad diesel engines and amending those rules to provide manufacturers with a production technical relief provision for Tier 3 equipment.

WindWaveFloat (WWF): Final Scientific Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alla Weinstein; Roddier, Dominique; Banister, Kevin

2012-03-30

Principle Power Inc. and National Renewable Energy Lab (NREL) have completed a contract to assess the technical and economic feasibility of integrating wave energy converters into the WindFloat, resulting in a new concept called the WindWaveFloat (WWF). The concentration of several devices on one platform could offer a potential for both economic and operational advantages. Wind and wave energy converters can share the electrical cable and power transfer equipment to transport the electricity to shore. Access to multiple generation devices could be simplified, resulting in cost saving at the operational level. Overall capital costs may also be reduced, provided thatmore » the design of the foundation can be adapted to multiple devices with minimum modifications. Finally, the WindWaveFloat confers the ability to increase energy production from individual floating support structures, potentially leading to a reduction in levelized energy costs, an increase in the overall capacity factor, and greater stability of the electrical power delivered to the grid. The research conducted under this grant investigated the integration of several wave energy device types into the WindFloat platform. Several of the resulting system designs demonstrated technical feasibility, but the size and design constraints of the wave energy converters (technical and economic) make the WindWaveFloat concept economically unfeasible at this time. Not enough additional generation could be produced to make the additional expense associated with wave energy conversion integration into the WindFloat worthwhile.« less

[Technical feasibility of the implantation of a monorail stent system into the renal arteries without pre-dilatation].

PubMed

Neumann, C; Gschwendtner, M; Karnel, F; Mair, J; Dorffner, G; Dorffner, R

2005-01-01

To evaluate the technical feasibility of the implantation of the monorail RX Herculink system into the renal arteries without pre-dilatation. Forty-two patients (mean age 71 years) from four centers with a total of 44 renal artery stenoses underwent implantation of the RX Herculink stent. The mean grade of the stenosis was 83.8 %, the mean length 7.5 mm. The stenoses were ostial in 38 cases and in immediate proximity to the ostium in 6 cases. The mean follow-up-period was 57 weeks (24 - 176 weeks). In 42 cases, the implantation was successful without pre-dilatation. In 2 cases, pre-dilatation was carried out. In none of the cases, detachment of the stent from the balloon was observed. In one stenosis with a length of 17 mm, implantation of two stents was performed. In 9 cases, post-dilatation with a larger balloon or higher balloon pressure was necessary. Residual stenoses exceeding 30 % were not observed. Two patients developed local bleeding at the puncture site. During the follow-up, restenoses were observed in 5 stents after 26 to 126 weeks, which necessitated a second intervention in 3 cases (PTA in 2 cases, re-stenting in 1 case). The primary patency rate after 6 and 12 months was 0.92 +/- 0.056 according to Kaplan-Meier, the secondary patency rate after 6 and 12 months was 1.0 +/- 0.0. Implantation of the RX Herculink stent system into the renal arteries without pre-dilatation is technically feasible and safe. Even without pre-dilatation, the stent-system can be advanced through the stenosis without detachment. The complication rate is low. Our clinical results are comparable to previous studies.

Experimental Program Final Technical Progress Report: 15 February 2007 to 30 September 2012

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kinney, Edward R.

2014-09-12

This is the final technical report of the grant DE-FG02-04ER41301 to the University of Colorado at Boulder entitled "Intermediate Energy Nuclear Physics" and describes the results of our funded activities during the period 15 February 2007 to 30 September 2012. These activities were primarily carried out at Fermilab, RHIC, and the German lab DESY. Significant advances in these experiments were carried out by members of the Colorado group and are described in detail.

Technical Report - FINAL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barbara Luke, Director, UNLV Engineering Geophysics Laboratory

2007-04-25

Improve understanding of the earthquake hazard in the Las Vegas Valley and to assess the state of preparedness of the area's population and structures for the next big earthquake. 1. Enhance the seismic monitoring network in the Las Vegas Valley 2. Improve understanding of deep basin structure through active-source seismic refraction and reflection testing 3. Improve understanding of dynamic response of shallow sediments through seismic testing and correlations with lithology 4. Develop credible earthquake scenarios by laboratory and field studies, literature review and analyses 5. Refine ground motion expectations around the Las Vegas Valley through simulations 6. Assess current buildingmore » standards in light of improved understanding of hazards 7. Perform risk assessment for structures and infrastructures, with emphasis on lifelines and critical structures 8. Encourage and facilitate broad and open technical interchange regarding earthquake safety in southern Nevada and efforts to inform citizens of earthquake hazards and mitigation opportunities« less

Final Technical Report for SISGR: Ultrafast Molecular Scale Chemical Imaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hersam, Mark C.; Guest, Jeffrey R.; Guisinger, Nathan P.

2017-04-10

The Northwestern-Argonne SISGR program utilized newly developed instrumentation and techniques including integrated ultra-high vacuum tip-enhanced Raman spectroscopy/scanning tunneling microscopy (UHV-TERS/STM) and surface-enhanced femtosecond stimulated Raman scattering (SE-FSRS) to advance the spatial and temporal resolution of chemical imaging for the study of photoinduced dynamics of molecules on plasmonically active surfaces. An accompanying theory program addressed modeling of charge transfer processes using constrained density functional theory (DFT) in addition to modeling of SE-FSRS, thereby providing a detailed description of the excited state dynamics. This interdisciplinary and highly collaborative research resulted in 62 publications with ~ 48% of them being co-authored by multiplemore » SISGR team members. A summary of the scientific accomplishments from this SISGR program is provided in this final technical report.« less

Feasibility of Computer-Based Videogame Therapy for Children with Cerebral Palsy.

PubMed

Radtka, Sandra; Hone, Robert; Brown, Charles; Mastick, Judy; Melnick, Marsha E; Dowling, Glenna A

2013-08-01

Standing and gait balance problems are common in children with cerebral palsy (CP), resulting in falls and injuries. Task-oriented exercises to strengthen and stretch muscles that shift the center of mass and change the base of support are effective in improving balance. Gaming environments can be challenging and fun, encouraging children to engage in exercises at home. The aims of this project were to demonstrate the technical feasibility, ease of use, appeal, and safety of a computer-based videogame program designed to improve balance in children with CP. This study represents a close collaboration between computer design and clinical team members. The first two phases were performed in the laboratory, and the final phase was done in subjects' homes. The prototype balance game was developed using computer-based real-time three-dimensional programming that enabled the team to capture engineering data necessary to tune the system. Videogame modifications, including identifying compensatory movements, were made in an iterative fashion based on feedback from subjects and observations of clinical and software team members. Subjects ( n =14) scored the game 21.5 out of 30 for ease of use and appeal, 4.0 out of 5 for enjoyment, and 3.5 on comprehension. There were no safety issues, and the games performed without technical flaws in final testing. A computer-based videogame incorporating therapeutic movements to improve gait and balance in children with CP was appealing and feasible for home use. A follow-up study examining its effectiveness in improving balance in children with CP is recommended.

Novel Multisensor Probe for Monitoring Bladder Temperature During Locoregional Chemohyperthermia for Nonmuscle-Invasive Bladder Cancer: Technical Feasibility Study

PubMed Central

Geijsen, Debby E.; Zum Vörde Sive Vörding, Paul J.; Schooneveldt, Gerben; Sijbrands, Jan; Hulshof, Maarten C.; de la Rosette, Jean; de Reijke, Theo M.; Crezee, Hans

2013-01-01

Abstract Background and Purpose: The effectiveness of locoregional hyperthermia combined with intravesical instillation of mitomycin C to reduce the risk of recurrence and progression of intermediate- and high-risk nonmuscle-invasive bladder cancer is currently investigated in clinical trials. Clinically effective locoregional hyperthermia delivery necessitates adequate thermal dosimetry; thus, optimal thermometry methods are needed to monitor accurately the temperature distribution throughout the bladder wall. The aim of the study was to evaluate the technical feasibility of a novel intravesical device (multi-sensor probe) developed to monitor the local bladder wall temperatures during loco-regional C-HT. Materials and Methods: A multisensor thermocouple probe was designed for deployment in the human bladder, using special sensors to cover the bladder wall in different directions. The deployment of the thermocouples against the bladder wall was evaluated with visual, endoscopic, and CT imaging in bladder phantoms, porcine models, and human bladders obtained from obduction for bladder volumes and different deployment sizes of the probe. Finally, porcine bladders were embedded in a phantom and subjected to locoregional heating to compare probe temperatures with additional thermometry inside and outside the bladder wall. Results: The 7.5 cm thermocouple probe yielded optimal bladder wall contact, adapting to different bladder volumes. Temperature monitoring was shown to be accurate and representative for the actual bladder wall temperature. Conclusions: Use of this novel multisensor probe could yield a more accurate monitoring of the bladder wall temperature during locoregional chemohyperthermia. PMID:24112045

Application of Communications Satellites to Educational Development. Final Technical Report, September 1, 1969-August 31, 1975.

ERIC Educational Resources Information Center

Morgan, Robert P.

Research is summarized in a brief final report built around a four-section bibliography. The first section lists periodic progress reports and articles which provide an overview of the program, including articles which pertain primarily to educational rather than technical aspects of satellite utilization. Theses carried out in the fields of…

78 FR 57264 - Final Waiver and Extension of the Project Period for the Technical Assistance Coordination Center

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-18

...: 84.326Z.] Final Waiver and Extension of the Project Period for the Technical Assistance Coordination... project period. SUMMARY: The Secretary waives the requirements in the Education Department General Administrative Regulations that generally prohibit project periods exceeding five years and extensions of project...

Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stoessel, Chris

2013-11-13

This project developed a new high-performance R-10/high SHGC window design, reviewed market positioning and evaluated manufacturing solutions required for broad market adoption. The project objectives were accomplished by: identifying viable technical solutions based on modeling of modern and potential coating stacks and IGU designs; development of new coating material sets for HM thin film stacks, as well as improved HM IGU designs to accept multiple layers of HM films; matching promising new coating designs with new HM IGU designs to demonstrate performance gains; and, in cooperation with a window manufacturer, assess the potential for high-volume manufacturing and cost efficiency ofmore » a HM-based R-10 window with improved solar heat gain characteristics. A broad view of available materials and design options was applied to achieve the desired improvements. Gated engineering methodologies were employed to guide the development process from concept generation to a window demonstration. The project determined that a slightly de-rated window performance allows formulation of a path to achieve the desired cost reductions to support end consumer adoption.« less

Base compaction specification feasibility analysis.

DOT National Transportation Integrated Search

2012-12-01

The objective of this research is to establish the technical engineering and cost : analysis concepts that will enable WisDOT management to objectively evaluate the : feasibility of switching construction specification philosophies for aggregate base...

West Angeles Community Development Corporation final technical report on export market feasibility planning and research for the solar medical autoclave

DOE Office of Scientific and Technical Information (OSTI.GOV)

Power, G.D.

1998-04-20

This report summarizes core findings from an investigation performed by the staff of West Angeles Community Development Corporation (CDC) regarding the feasibility of marketing the Solar Medical Autoclave (``autoclave``) in South Africa. The investigation was completed during 1997, the period prescribed by the Grant Award made by the U.S. Department of Energy on January 1, 1997, and was monitored by the National Renewable Energy Laboratory.

A technical feasibility study of surfactant-free drug suspensions using octenyl succinate-modified starches.

PubMed

Kuentz, Martin; Egloff, Peter; Röthlisberger, Dieter

2006-05-01

Many new drugs exhibit poor wetting behaviour and low aqueous solubility. This is particularly an issue for preclinical studies like toxicological trials, in which considerably higher doses and volumes are being administered compared to clinical studies. Preclinical vehicles typically contain high levels of surfactants that can exert biological effects. However, the biological inertness of vehicles is pivotal for the application in preclinical studies stressing the need in finding new excipients to solve formulation problems of today's drug discovery. The present study investigated the technical feasibility of surfactant-free suspensions using a new poorly soluble drug as model. It was shown that octenyl succinate-modified starches adequately wetted the drug and homogenous tasteless suspensions were obtained. The polymer xanthan gum was identified as macroscopically compatible gelling agent. Concentration effects of xanthan, drug and different modified starches were studied in a D-optimal design with respect to rheological properties. The suspensions were also tested in an analytical centrifuge using NIR transmission profiles to obtain a measure of sedimentation stability under accelerated conditions. The modified starches exhibited only little influence on the viscosity as well as on the yield point in contrast to the rheological effects of xanthan gum. This gelling agent was the main stabilising excipient as the modified starches hindered to a lesser extent sedimentation. The most stable suspensions displayed convenient flow properties. The viscosity at 100 s(-1) and 25 degrees C was in technically acceptable range of 120-140 mPa s in view of a application via gavage or a syringe in animal studies. The results demonstrated that surfactant-free drug suspensions with excellent technical performance can be obtained using octenyl succinate-modified starches. The vehicles were tasteless and based on the experience of modified starches in the food industry, the

Technical feasibility and revision efficacy of the sequential deployment of endoscopic bilateral side-by-side metal stents for malignant hilar biliary strictures: a multicenter prospective study.

PubMed

Lee, Tae Hoon; Park, Do Hyun; Lee, Sang Soo; Choi, Hyun Jong; Lee, Jun Kyu; Kim, Tae Hyeon; Kim, Jong Hyeok; Jeong, Seok; Park, Sang-Heum; Moon, Jong Ho

2013-02-01

Theoretically, the side-by-side bilateral placement of metal stents may be technically easier than stent-in-stent bilateral placement in stent revision. However, side-by-side placement can be technically challenging, as the deployment of the first stent can preclude the passage of the second stent. We explored the technical feasibility and revision efficacy of endoscopic bilateral side-by-side stent placement for malignant hilar biliary strictures. Forty-four patients with Bismuth type II or higher malignant hilar biliary strictures were enrolled in seven academic tertiary referral centers. Endoscopic placement of side-by-side bilateral metal stents with 7F thin delivery shaft was performed. The outcome measurements were the technical and functional success, adverse events, endoscopic revision success rate, and stent patency. Overall, the technical and functional success rates were 91 % (40/44), and 98 % (39/40), respectively. Two of the failed patients were converted successfully with subsequent contralateral stent-in-stent placement, and the other patients underwent percutaneous intervention. Early stent-related adverse events occurred in 10 %. The endoscopic revision rate due to stent malfunction during follow-up (median: 180 days) was 45 % (18/40; tumor ingrowth in 4 and in-stent sludge impaction/stone formation in 14 patients). The endoscopic revision success rate was 92 % (12/13). Five patients with comorbidity underwent initial percutaneous intervention. The median survival and stent patency periods were 180 and 157 days, respectively. The sequential placement of a metal stent with a 7F thin delivery shaft in bilateral side-by-side procedures may be feasible and effective for malignant hilar biliary strictures and for endoscopic stent revision.

Telephone Flat Geothermal Development Project Environmental Impact Statement Environmental Impact Report. Final

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

This Final Environmental Impact Statement and Environmental Impact Report (Final EIS/EIR) has been prepared to meet the requirements of the National Environmental Policy Act (NEPA) and the California Environmental Quality Act (CEQA). The Proposed Action includes the construction, operation, and decommissioning of a 48 megawatt (gross) geothermal power plant with ancillary facilities (10-12 production well pads and 3-5 injection well pads, production and injection pipelines), access roads, and a 230-kilovolt (kV) transmission line in the Modoc National Forest in Siskiyou County, California. Alternative locations for the power plant site within a reasonable distance of the middle of the wellfield weremore » determined to be technically feasible. Three power plant site alternatives are evaluated in the Final EIS/EIR.« less

Feasibility Study to Identify Potential Reductions in Energy Use in Tribal Buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stevens, Willie

Under this project, the Confederated Salish and Kootenai Tribes (CSKT) assessed the technical and economic feasibility of energy efficiency improvements to existing Tribally-owned buildings. The feasibility study followed a systematic approach in identifying, selecting, and ranking recommended measures, recognizing that the appropriateness of a measure would depend not only on technical issues but also on institutional and organizational issues, such as financing options and occupant requirements. The completed study provided the Tribes with the information needed to commit necessary resources to reduce the energy use and cost in approximately 40 Tribal buildings, including the changes that may be needed inmore » each facility’s operation and maintenance and personnel requirements. It also presented an economic analysis of energy-efficiency capital improvements and an annotated list of financing options and possible funding sources for implementation and an overall strategy for implementation. This project was located in various Tribal communities located throughout the Flathead Indian Reservation in Western Montana. Notice: The following is a compilation of Annual Program Review Presentations, Award Modifications, and Quarterly Progress Reports submitted to the Department of Energy’s (DOE) Office of Indian Energy Policy and Programs by the Confederated Salish and Kootenai Tribes under agreement DE-EE0005171. This report covers project activities from September 30, 2011 through December 31, 2014 and has been uploaded to OSTI by DOE as a substitute for the required Final Technical Report which was not received by DOE from the project recipient.« less

White Earth Biomass/Biogas Feasibility Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Triplett, Michael

2015-03-12

The White Earth Nation examined the feasibility of cost savings and fossil energy reduction through the installation of biogas/biomass boiler at the tribal casino. The study rejected biogas options due to availability and site constraints, but found a favorable environment for technical and financial feasibility of installing a 5 MMBtu hot water boiler system to offset 60-70 percent of current fuel oil and propane usage.

Solar UV exposure among outdoor workers in Denmark measured with personal UV-B dosimeters: technical and practical feasibility.

PubMed

Grandahl, Kasper; Mortensen, Ole Steen; Sherman, David Zim; Køster, Brian; Lund, Paul-Anker; Ibler, Kristina Sophie; Eriksen, Paul

2017-10-10

Exposure to solar ultraviolet radiation is a well-known cause of skin cancer. This is problematic for outdoor workers. In Denmark alone, occupational skin cancer poses a significant health and safety risk for around 400,000 outdoor workers. Objective measures of solar ultraviolet radiation exposure are needed to help resolve this problem. This can be done using personal ultraviolet radiation dosimeters. We consider technical and practical feasibility of measuring individual solar ultraviolet exposure at work and leisure in professions with different á priori temporal high-level outdoor worktime, using aluminium gallium nitride (AlGaN) photodiode detector based personal UV-B dosimeters. Essential technical specifications including the spectral and angular responsivity of the dosimeters are described and pre-campaign dosimeter calibration applicability is verified. The scale and conduct of dosimeter deployment and campaign in-field measurements including failures and shortcomings affecting overall data collection are presented. Nationwide measurements for more than three hundred and fifty workers from several different professions were collected in the summer of 2016. On average, each worker's exposure was measured for a 2-week period, which included both work and leisure. Data samples of exposure at work during a Midsummer day show differences across professions. A construction worker received high-level occupational UV exposure most of the working day, except during lunch hour, accumulating to 5.1 SED. A postal service worker was exposed intermittently around noon and in the afternoon, preceded by no exposure forenoon when packing mail, accumulating to 1.6 SED. A crane fitter was exposed only during lunch hour, accumulating to 0.7 SED. These findings are in line with our specialist knowledge as occupational physicians. Large-scale use of personal UV-B dosimeters for measurement of solar ultraviolet radiation exposure at work and leisure in Denmark is indeed

Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kirkpatrick, R. James

This document serves as the final report for United States Department of Energy Basic Energy Sciences Grant DE-FG02-08ER15929, “Computational and Spectroscopic Investigations of the Molecular Scale Structure and Dynamics of Geologically Important Fluids and Mineral-Fluid Interfaces” (R. James Kirkpatrick, P.I., A. O. Yazaydin, co-P.I.). The research under this grant was intimately tied to that supported by the parallel the grant of the same title at Alfred (DOE DE-FG02-10ER16128; Geoffrey M. Bowers, P.I.).

Feasibility of Computer-Based Videogame Therapy for Children with Cerebral Palsy

PubMed Central

Radtka, Sandra; Hone, Robert; Brown, Charles; Mastick, Judy; Melnick, Marsha E.

2013-01-01

Abstract Objectives Standing and gait balance problems are common in children with cerebral palsy (CP), resulting in falls and injuries. Task-oriented exercises to strengthen and stretch muscles that shift the center of mass and change the base of support are effective in improving balance. Gaming environments can be challenging and fun, encouraging children to engage in exercises at home. The aims of this project were to demonstrate the technical feasibility, ease of use, appeal, and safety of a computer-based videogame program designed to improve balance in children with CP. Materials and Methods This study represents a close collaboration between computer design and clinical team members. The first two phases were performed in the laboratory, and the final phase was done in subjects' homes. The prototype balance game was developed using computer-based real-time three-dimensional programming that enabled the team to capture engineering data necessary to tune the system. Videogame modifications, including identifying compensatory movements, were made in an iterative fashion based on feedback from subjects and observations of clinical and software team members. Results Subjects (n=14) scored the game 21.5 out of 30 for ease of use and appeal, 4.0 out of 5 for enjoyment, and 3.5 on comprehension. There were no safety issues, and the games performed without technical flaws in final testing. Conclusions A computer-based videogame incorporating therapeutic movements to improve gait and balance in children with CP was appealing and feasible for home use. A follow-up study examining its effectiveness in improving balance in children with CP is recommended. PMID:24761324

Final Technical Progress Report: Development of Low-Cost Suspension Heliostat; December 7, 2011 - December 6, 2012

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bender, W.

2013-01-01

Final technical progress report of SunShot Incubator Solaflect Energy. The project succeeded in demonstrating that the Solaflect Suspension Heliostat design is viable for large-scale CSP installations. Canting accuracy is acceptable and is continually improving as Solaflect improves its understanding of this design. Cost reduction initiatives were successful, and there are still many opportunities for further development and further cost reduction.

Economic and Technical Feasibility Study of Utility-Scale Wind Generation for the New York Buffalo River and South Buffalo Brownfield Opportunity Areas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roberts, J. O.; Mosey, G.

2014-04-01

Through the RE-Powering America's Land initiative, the economic and technical feasibility of utilizing contaminated lands in the Buffalo, New York, area for utility-scale wind development is explored. The study found that there is available land, electrical infrastructure, wind resource, and local interest to support a commercial wind project; however, economies of scale and local electrical markets may need further investigation before significant investment is made into developing a wind project at the Buffalo Reuse Authority site.

Focused Feasibility Study Final Field Sampling Plan

DTIC Science & Technology

1993-10-01

baseline of groundwater chemistry prior to commencing additional environmental investigations of the area. Work for Phase I of the FFS is designed lo...investigations and remedial feasibility investigations at Beach Point. The groundwater data will also be used to aid in the design of any groundwater extraction...approved laboratories. The analytical data will be the equivalent of EPA Level IV data. This level of data quality has been established for environmental

An independent assessment of the technical feasibility of the Mars One mission plan - Updated analysis

NASA Astrophysics Data System (ADS)

Do, Sydney; Owens, Andrew; Ho, Koki; Schreiner, Samuel; de Weck, Olivier

2016-03-01

In recent years, the Mars One program has gained significant publicity for its plans to colonize the red planet. Beginning in 2025, the program plans to land four people on Mars every 26 months via a series of one-way missions, using exclusively existing technology. This one-way approach has frequently been cited as a key enabler of accelerating the first crewed landing on Mars. While the Mars One program has received considerable attention, little has been published in the technical literature regarding the formulation of its mission architecture. In light of this, we perform an independent analysis of the technical feasibility of the Mars One mission plan, focusing on the architecture of the life support and in-situ resource utilization (ISRU) systems, and their impact on sparing and space logistics. To perform this analysis, we adopt an iterative analysis approach in which we model and simulate the mission architecture, assess its feasibility, implement any applicable modifications while attempting to remain within the constraints set forth by Mars One, and then resimulate and reanalyze the revised version of the mission architecture. Where required information regarding the Mars One mission architecture is not available, we assume numerical values derived from standard spaceflight design handbooks and documents. Through four iterations of this process, our analysis finds that the Mars One mission plan, as publicly described, is not feasible. This conclusion is obtained from analyses based on mission assumptions derived from and constrained by statements made by Mars One, and is the result of the following findings: (1) several technologies including ISRU, life support, and entry, descent, and landing (EDL) are not currently "existing, validated and available" as claimed by Mars One; (2) the crop growth area described by Mars One is insufficient to feed their crew; (3) increasing the crop growth area to provide sufficient food for the crew leads to atmospheric

Matching Community and Technical College Professional/Technical Education Capacity to Employer Demand. Final Report.

ERIC Educational Resources Information Center

Sommers, Paul; Heg, Deena

A project was conducted to improve the state of Washington's community and technical college system by developing and using an improved occupational forecasting system to assess and respond to education and training needs. First, long-term occupational forecast data from Washington's Employment Security Department were matched with technical and…

Technical innovation: Intragastric Single Port Sleeve Gastrectomy (IGSG). A feasibility survival study on porcine model.

PubMed

Estupinam, Oscar; Oliveira, André Lacerda de Abreu; Antunes, Fernanda; Galvão, Manoel; Phillips, Henrique; Scheffer, Jussara Peters; Rios, Marcelo; Zorron, Ricardo

2018-01-01

To perform technically the laparoscopic sleeve gastrectomy (LSG) using a unique Intragastric Single Port (IGSG) in animal swine model, evidencing an effective and safe procedure, optimizing the conventional technique. IGSG was performed in 4 minipigs, using a percutaneous intragastric single port located in the pre-pyloric region. The gastric stapling of the greater curvature started from the pre-pyloric region towards the angle of His by Endo GIA™ system and the specimen was removed through the single port. In the postoperative day 30, the animals were sacrificed and submitted to autopsy. All procedures were performed without conversion, and all survived 30 days. The mean operative time was 42 min. During the perioperative period no complications were observed during invagination and stapling. No postoperative complications occurred. Post-mortem examination showed no leaks or infectious complications. Intragastric Single Port is a feasible procedure that may be a suitable alternative technique of sleeve gastrectomy for the treatment of morbid obesity.

NEET-AMM Final Technical Report on Laser Direct Manufacturing (LDM) for Nuclear Power Components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, Scott; Baca, Georgina; O'Connor, Michael

2015-12-31

Final technical report summarizes the program progress and technical accomplishments of the Laser Direct Manufacturing (LDM) for Nuclear Power Components project. A series of experiments varying build process parameters (scan speed and laser power) were conducted at the outset to establish the optimal build conditions for each of the alloys. Fabrication was completed in collaboration with Quad City Manufacturing Laboratory (QCML). The density of all sample specimens was measured and compared to literature values. Optimal build process conditions giving fabricated part densities close to literature values were chosen for making mechanical test coupons. Test coupons whose principal axis is onmore » the x-y plane (perpendicular to build direction) and on the z plane (parallel to build direction) were built and tested as part of the experimental build matrix to understand the impact of the anisotropic nature of the process.. Investigations are described 316L SS, Inconel 600, 718 and 800 and oxide dispersion strengthed 316L SS (Yttria) alloys.« less

Feasibility Study of Training Environmental Technicians. Final Report.

ERIC Educational Resources Information Center

Vernon, James Y.; Garrett, Donald M.

A feasibility study and task analysis was performed to determine the future job potential within the Southern California area for environmental technicians trained under a proposed vocational training program in community colleges. Questionnaires were mailed to possible employers in government and industry to obtain information about their…

Extraforaminal Lumbar Interbody Fusion at the L5-S1 Level: Technical Considerations and Feasibility.

PubMed

Kurzbuch, Arthur Robert; Kaech, Denis; Baranowski, Pawel; Baranowska, Alicja; Recoules-Arche, Didier

2017-09-01

Background  Extraforaminal lumbar interbody fusion (ELIF) surgery is a muscle-sparing approach that allows the treatment of various degenerative spinal diseases. It is technical challenging to perform the ELIF approach at the L5-S1 level because the sacral ala obstructs the view of the intervertebral disk space. Methods  We reported earlier on the ELIF technique in which the intervertebral disk is targeted at an angle of 45 degrees relative to the midline. In this article we describe the technical process we developed to overcome the anatomic relation between the sacral ala and the intervertebral disk space L5-S1 that hinders the ELIF approach at this level. We then report in a retrospective analysis on the short-term clinical and radiologic outcome of 100 consecutive patients with degenerative L5-S1 pathologies who underwent ELIF surgery. Results  The L5-S1 ELIF approach could be realized in all patients. The short-term clinical outcome was evaluated 5 months after surgery: 92% of the patients were satisfied with their postoperative result; 8% had a poor result. Overall, 17% of the patients presented light radicular or low back pain not influencing their daily activity, and 82% of the patients working before surgery returned to work 3 to 7 months after surgery. The radiologic outcome was documented by computed tomography at 5 months after surgery and showed fusion in 99% of the patients. Lumbar magnetic resonance imaging performed in 5 patients at 6 months after surgery revealed the integrity of the paraspinal muscles. Conclusions  ELIF surgery at the L5-S1 level is technically feasible for various degenerative spinal diseases. Analysis of the clinical and radiologic data in a consecutive retrospective cohort of patients who underwent this surgical procedure showed a good short-term clinical outcome and fusion rate. Georg Thieme Verlag KG Stuttgart · New York.

Vapor detection of trafficking of contraband money: A discussion of technical feasibility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dietz, R.N.

1996-02-01

For every two pounds of cocaine smuggled into the US, drug traffikers are being forced to clandestinely ship three pounds of money back out for subsequent laundering. Based on tracer technology developed for validation of long-range atmospheric transport models and other commercial applications, it is shown that US currency can be tagged with a minute amount (about 1 ppm by weight of a bill) of perfluorocharbon tracer (PFT) material that is sufficient to last for about 30 years and yet provide a vapor emission rate suitable for detectability of modest caches of contraband money in vehicles at border crossings, onmore » aircraft at international terminals, and in buildings. The cost of tagging is less than $5 per million bills; the taggant quantity should have no impact on the feel of a bill. The low emission rate would not allow detectability of usual amounts of money in typical scenarios, providing an essential degree of privacy, but extraordinary amounts would be detectable using specialized instrumentation and know-how not easily attainable but commercially in production; an example of sub-part-per-quadrillion detection of a proposed PFT taggant is demonstrated using a prototype commercial unit. An outline of a research and demonstration program to achieve this capability and details of the proposed tagging and detection procedures already indicate that the concept is technically feasible.« less

Feasibility of Retrofitting Lifts on Commuter and Light Rail Vehicles

DOT National Transportation Integrated Search

1980-09-01

The objectives of this study were to determine if lift retrofit applications to rail vehicles are technically feasible, and if so, the extent to which existing bus lift technology can be utilized. This report examines some of the technical issues ass...

Feasibility of adapting a classroom balance training program to a video game platform for people with Parkinson's disease.

PubMed

Dowling, Glenna A; Hone, Robert; Brown, Charles; Mastick, Judy; Melnick, Marsha

2013-04-01

Decreased postural stability in people with Parkinson's disease (PD) is a major component of disability. Rehabilitation interventions are therefore targeted to improve balance, mobility, and strength. Virtual environment and gaming platforms can encourage therapeutic activity in the home and be challenging and fun. The aims of the project were to demonstrate the technical feasibility of adapting a classroom-based gait-and-balance training program to a video game platform. Ease of use, appeal, and safety of the proposed games were tested for both clinic and in-home use. This cross-sectional observational study was carried out in three phases. Modifications in the game platform were made in an iterative fashion based on feedback from subjects and the observations of clinical and design team members. The first two phases of testing were performed in a laboratory setting, and the final phase was carried out in subjects' homes. Subjects (n=20) scored the primary "Rail Runner" game 3.6 for ease of use (1=hard, 5=easy) and 3.9 for appeal (1=did not like at all, 5=liked very much). There were no safety issues encountered, and the games performed without technical flaws in the final phase of testing. A computer-based video game that incorporates therapeutic movements to improve gait and balance for people with PD was appealing to subjects and feasible for home use.

DC-9/JT8D refan, Phase 1. [technical and economic feasibility of retrofitting DC-9 aircraft with refan engine to achieve desired acoustic levels

NASA Technical Reports Server (NTRS)

1973-01-01

Analyses and design studies were conducted on the technical and economic feasibility of installing the JT8D-109 refan engine on the DC-9 aircraft. Design criteria included minimum change to the airframe to achieve desired acoustic levels. Several acoustic configurations were studied with two selected for detailed investigations. The minimum selected acoustic treatment configuration results in an estimated aircraft weight increase of 608 kg (1,342 lb) and the maximum selected acoustic treatment configuration results in an estimated aircraft weight increase of 809 kg (1,784 lb). The range loss for the minimum and maximum selected acoustic treatment configurations based on long range cruise at 10 668 m (35,000 ft) altitude with a typical payload of 6 804 kg (15,000 lb) amounts to 54 km (86 n. mi.) respectively. Estimated reduction in EPNL's for minimum selected treatment show 8 EPNdB at approach, 12 EPNdB for takeoff with power cutback, 15 EPNdB for takeoff without power cutback and 12 EPNdB for sideline using FAR Part 36. Little difference was estimated in EPNL between minimum and maximum treatments due to reduced performance of maximum treatment. No major technical problems were encountered in the study. The refan concept for the DC-9 appears technically feasible and economically viable at approximately $1,000,000 per airplane. An additional study of the installation of JT3D-9 refan engine on the DC-8-50/61 and DC-8-62/63 aircraft is included. Three levels of acoustic treatment were suggested for DC-8-50/61 and two levels for DC-8-62/63. Results indicate the DC-8 technically can be retrofitted with refan engines for approximately $2,500,000 per airplane.

Georgetown University Integrated Community Energy System (GU-ICES). Phase III, Stage I. Feasibility analysis. Final report. Volume 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

This Feasibility Analysis covers a wide range of studies and evaluations. The Report is divided into five parts. Section 1 contains all material relating to the Institutional Assessment including consideration of the requirements and position of the Potomac Electric Co. as they relate to cogeneration at Georgetown in parallel with the utility (Task 1). Sections 2 through 7 contain all technical information relating to the Alternative Subsystems Analysis (Task 4). This includes the energy demand profiles upon which the evaluations were based (Task 3). It further includes the results of the Life-Cycle-Cost Analyses (Task 5) which are developed in detailmore » in the Appendix for evaluation in the Technical Report. Also included is the material relating to Incremental Savings and Optimization (Task 6) and the Conceptual Design for candidate alternate subsystems (Task 7). Section 8 contains all material relating to the Environmental Impact Assessment (Task 2). The Appendix contains supplementary material including the budget cost estimates used in the life-cycle-cost analyses, the basic assumptions upon which the life-cycle analyses were developed, and the detailed life-cycle-cost anlysis for each subsystem considered in detail.« less

Florida Study of Career and Technical Education. Final Report

ERIC Educational Resources Information Center

Jacobson, Louis; Mokher, Christine

2014-01-01

A key goal of the "Carl D. Perkins Career and Technical Education Act of 2006" ("Perkins IV") is to ensure career and technical education (CTE) programs are widely available for preparing high school and college students for "high skill, high wage, or high demand occupations in current or emerging professions"…

Simulation-based ureteroscopy skills training curriculum with integration of technical and non-technical skills: a randomised controlled trial.

PubMed

Brunckhorst, Oliver; Shahid, Shahab; Aydin, Abdullatif; McIlhenny, Craig; Khan, Shahid; Raza, Syed Johar; Sahai, Arun; Brewin, James; Bello, Fernando; Kneebone, Roger; Khan, Muhammad Shamim; Dasgupta, Prokar; Ahmed, Kamran

2015-09-01

Current training modalities within ureteroscopy have been extensively validated and must now be integrated within a comprehensive curriculum. Additionally, non-technical skills often cause surgical error and little research has been conducted to combine this with technical skills teaching. This study therefore aimed to develop and validate a curriculum for semi-rigid ureteroscopy, integrating both technical and non-technical skills teaching within the programme. Delphi methodology was utilised for curriculum development and content validation, with a randomised trial then conducted (n = 32) for curriculum evaluation. The developed curriculum consisted of four modules; initially developing basic technical skills and subsequently integrating non-technical skills teaching. Sixteen participants underwent the simulation-based curriculum and were subsequently assessed, together with the control cohort (n = 16) within a full immersion environment. Both technical (Time to completion, OSATS and a task specific checklist) and non-technical (NOTSS) outcome measures were recorded with parametric and non-parametric analyses used depending on the distribution of our data as evaluated by a Shapiro-Wilk test. Improvements within the intervention cohort demonstrated educational value across all technical and non-technical parameters recorded, including time to completion (p < 0.01), OSATS scores (p < 0.001), task specific checklist scores (p = 0.011) and NOTSS scores (p < 0.001). Content validity, feasibility and acceptability were all demonstrated through curriculum development and post-study questionnaire results. The current developed curriculum demonstrates that integrating both technical and non-technical skills teaching is both educationally valuable and feasible. Additionally, the curriculum offers a validated simulation-based training modality within ureteroscopy and a framework for the development of other simulation-based programmes.

Technical Feasibility Aspects of the Geothermal Resource Reporting Methodology (GRRM)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Badgett, Alex; Young, Katherine R; Dobson, Patrick F.

This paper reviews the technical assessment of the Geothermal Research Reporting Methodology (GRRM, http://en.openei.org/wiki/GRRM) being developed for reporting geothermal resources and project progress. The goal of the methodology is to provide the U.S. Department of Energy's Geothermal Technologies Office (GTO) with a consistent and comprehensible means of evaluating the impacts of its funding programs. The GRRM is designed to provide uniform assessment criteria for geothermal resource grades and developmental phases of geothermal resource exploration and development. This resource grade system provides information on twelve attributes of geothermal resource locations (e.g., temperature, permeability, land access) to indicate potential for geothermal development.more » The GTO plans to use these Protocols to help quantitatively identify the greatest barriers to geothermal development, develop measureable program goals that will have the greatest impact to geothermal deployment, objectively evaluate proposals based (in part) on a project's ability to contribute to program goals, monitor project progress, and report on GTO portfolio performance. The GRRM assesses three areas of geothermal potential: geological, socio-economic, and technical. Previous work and publications have discussed the work done on the geological aspects of this methodology (Young et al. 2015c); this paper details the development of the technical assessment of the GRRM. Technical development attributes considered include: reservoir management, drilling, logistics, and power conversion.« less

Final Scientific/Technical Report for Program Title: Solar Powered Dewvaporation Desalination System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ranganathan, Shashidhar

Desalination technologies have been used increasingly throughout the world to produce the drinking water from the brackish ground and sea water for the past few decades. Among the commercially available desalination technologies, reverse osmosis (RO) and multi-stage flash distillation are the most widely used technologies globally. However, these technologies are difficult to be directly integrated with green energies without converting them to electricity. Dewvaporation, a desalination process, uses saturated steam as a carrier-gas to evaporate water from saline feeds and form pure condensate. It has the major technical benefit of reusing energy, released from vapor condensation, multiple times. The currentmore » proposal has been planned to address this issue. In Phase I, we have successfully demonstrated the feasibility of a new plasmonic nanoparticle based approach through fabrication and evaluation of a solar powered water vapor generation module. The water vapor generation module allows generation of high temperature plasmon on a fiber bundle end, where strong water and plasmon interaction occurs generating water vapor. Plasmon enhanced water evaporation has been realized on plasmonic nanoparticle immobilized substrate with an energy conversion efficiency of over 50%.« less

Florida Tech CubeSat Experiment Feasibility Study

NASA Technical Reports Server (NTRS)

Arrasmith, William W.; Bucaille, Stephane; Rusovici, Razvan; Platt, Don; Guidry, Todd; Bandar, Deepika; Coots, Everett; Davidson, Russ

2010-01-01

CubeSats are a relatively new type of satellite. Smaller than long-term (5+ year life expectancy) satellites, these pico-satellites are comparatively cheap, small (10x10x10 cm), and are very versatile. Universities world-wide are using CubeSats to conduct a variety of experiments in space without the need for a large experimental platform. Today CubeSats are considered to be one of the most effective ways to send a small payload into space and has attracted the attention of many educational and non-profit organizations. As this pico-satellite model continues to gain penetration into the satellite build and launch industry, it is expected that more governmental, educational, and commercial interests will emerge. As an example, more of the space-related items of high interest to the National Science Foundation may be tackled with a CubeSat platform resulting in lower life cycle costs than traditional satellite options. NASA LSP, in cooperation with the Florida Institute of Technology, has initiated a feasibility study to investigate the technical aspects of measuring and transferring vibration, acceleration, temperature, and video data from a CubeSat to NASA Hanger AE on Cape Canaveral Air Force Station (CCAFS) a.k.a. Kennedy Space Center (KSC). This report provides a technical feasibility analysis to determine whether-or-not a specific set of NASA/LSP requirements can be accomplished. Our approach has been to provide a "notional" component layout to determine the feasibility of the NASA/LSP stakeholder requirements. The notional layout is used to consider component level technical issues such as size, weight, & power (SWaP), bandwidth, and other critical technical parameters. Even though the notional components may satisfy the stated requirements and thereby demonstrate feasibility, the notional layout is NOT considered a design since no component optimization and design trade-off analysis has taken place. This activity should be accomplished in an appropriate

Energy utilization: municipal waste incineration. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

LaBeck, M.F.

An assessment is made of the technical and economical feasibility of converting municipal waste into useful and useable energy. The concept presented involves retrofitting an existing municipal incinerator with the systems and equipment necessary to produce process steam and electric power. The concept is economically attractive since the cost of necessary waste heat recovery equipment is usually a comparatively small percentage of the cost of the original incinerator installation. Technical data obtained from presently operating incinerators designed specifically for generating energy, documents the technical feasibility and stipulates certain design constraints. The investigation includes a cost summary; description of process andmore » facilities; conceptual design; economic analysis; derivation of costs; itemized estimated costs; design and construction schedule; and some drawings.« less

Review of Final Year MSP Evaluations, Performance Period 2007. Analytic and Technical Support for Mathematics and Science Partnerships

ERIC Educational Resources Information Center

Bobronnikov, Ellen; Rhodes, Hilary; Bradley, Cay

2010-01-01

This final report culminates the evaluation and technical assistance provided for the U.S. Department of Education's Mathematics and Science Partnership (MSP) Program and its projects since 2005. As part of this support, Abt Associates looked across the portfolio of projects funded by the MSP program to draw lessons on best practices. This…

A web-based communication system for integrated care in cerebral palsy: design features, technical feasibility and usability.

PubMed

Gulmans, Jitske; Vollenbroek-Hutten, Miriam M R; Visser, Jacqueline J W; Nijeweme-d'Hollosy, Wendy Oude; van Gemert-Pijnen, J E W C Lisette; van Harten, Wim H

2010-01-01

We developed a secure, web-based system for parent-professional and inter-professional communication. The aim was to improve communication in the care of children with cerebral palsy. We conducted a six-month trial of the system in three Dutch health-care regions. The participants were the parents of 30 cerebral palsy patients and 120 professional staff involved in their care. Information about system usage was extracted from the system's database. The experience of the parents and professionals was evaluated by a questionnaire after six months. The system proved to be technically robust and reliable. A total of 21 parents (70%) and 66 professionals (55%) used the system. The parents submitted 111 questions and 59 responses, with a mean of 5 questions (range 1-17) and 3 responses (range 1-9) per parent. The professionals submitted 79 questions and 237 responses, with a mean of 2 questions (range 1-8) and 4 responses (range 1-23) per professional. Most parents (95%) and some professionals (30%) reported value in using the system, which ranged from efficiency and accessibility to flexibility and transparency. The web-based communication system was technically feasible and produced improved parent-professional and inter-professional communication. It may be especially valuable if frequent interventions or consultations about a child's care are required, involving complex care networks of different professionals and organisations.

Technical and economic feasibility of alternative fuel use in process heaters and small boilers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-02-01

The technical and economic feasibility of using alternate fuels - fuels other than oil and natural gas - in combustors not regulated by the Powerplant and Industrial Fuel Use Act of 1978 (FUA) was evaluated. FUA requires coal or alternate fuel use in most large new boilers and in some existing boilers. Section 747 of FUA authorizes a study of the potential for reduced oil and gas use in combustors not subject to the act: small industrial boilers with capacities less than 100 MMBtu/hr, and process heat applications. Alternative fuel use in combustors not regulated by FUA was examined andmore » the impact of several measures to encourage the substitution of alternative fuels in these combustors was analyzed. The primary processes in which significant fuel savings can be achieved are identified. Since feedstock uses of oil and natural gas are considered raw materials, not fuels, feedstock applications are not examined in this analysis. The combustors evaluated in this study comprise approximately 45% of the fuel demand projected in 1990. These uses would account for more than 3.5 million barrels per day equivalent fuel demand in 1990.« less

Rock Melt Borehole Sealing System, Final Technical Report for SBIR Phase I Grant No. DE-SC0011888

DOE Office of Scientific and Technical Information (OSTI.GOV)

Osnes, John D.; Vining, Cody A.; Nopola, Jay R.

Purpose of Research Deep borehole disposal is one option that has received attention in recent years as a possible strategy for long-term disposal of the tens of thousands of tons of spent nuclear fuel. The feasibility of the deep borehole option relies upon designing and constructing an effective seal within the borehole to ensure that the waste package does not communicate with the shallow subsurface biosphere through the borehole itself. Some of the uncertainty associated with the long-term suitability of the deep borehole option is related to (1) the degradation of traditional sealing materials over time and (2) the inabilitymore » of traditional sealing methods to adequately seal a Disturbed Rock Zone surrounding the borehole. One possible system to address these concerns consists of encapsulating the waste in a melt generated from either the waste itself or a plug above the waste. This current project expanded on previous work to further advance the deep borehole disposal concept. Research Objectives & Findings The overarching objective of the study was to evaluate the feasibility of constructing a downhole heater that is capable of meeting the technical and logistical requirements to melt rock. This ultimate objective was accomplished by two primary approaches. The first approach was to define the heater requirements and conceptually design a system that is capable of melting rock. The second approach was to determine the feasibility of conducting an in situ, field-scale melting experiment to validate the suitability of the rock melt seal concept. The evaluation and conceptual design of the heater system resulted in the following primary findings: • Borehole wall temperatures capable of producing a partial melt are achievable under most expected thermal conductivities with a 12-kilowatt heater. • Commercially available components have been identified that meet the requirements of the heater system, including resistive elements that are capable of

Anticipatory precrash restraint sensor feasibility study: Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kercel, S.W.; Dress, W.B.

1995-08-01

This report explores feasibility of an anticipatory precrash restraint sensor. The foundation principle is the anticipation mechanism found at a primitive level of biological intelligence and originally formalized by the mathematical biologist Robert Rosen. A system based on formal anticipatory principles should significantly outperform conventional technologies. It offers the prospect of high payoff in prevention of death and injury. Sensors and processes are available to provide a good, fast, and inexpensive description of the present dynamical state of the vehicle to the embedded system model in the anticipation engine. The experimental part of this study found that inexpensive radar inmore » a real-world setting does return useful data on target dynamics. The data produced by a radar system can be converted to target dynamical information by good, fast and inexpensive signal-processing techniques. Not only is the anticipatory sensor feasible, but further development under the sponsorship of the National Highway Traffic Safety Administration is necessary and desirable. There are a number of possible lines of follow-on investigation. The level of effort and expected benefits of various alternatives are discussed.« less

Final Progress Report: Isotope Identification Algorithm for Rapid and Accurate Determination of Radioisotopes Feasibility Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rawool-Sullivan, Mohini; Bounds, John Alan; Brumby, Steven P.

2012-04-30

This is the final report of the project titled, 'Isotope Identification Algorithm for Rapid and Accurate Determination of Radioisotopes,' PMIS project number LA10-HUMANID-PD03. The goal of the work was to demonstrate principles of emulating a human analysis approach towards the data collected using radiation isotope identification devices (RIIDs). It summarizes work performed over the FY10 time period. The goal of the work was to demonstrate principles of emulating a human analysis approach towards the data collected using radiation isotope identification devices (RIIDs). Human analysts begin analyzing a spectrum based on features in the spectrum - lines and shapes that aremore » present in a given spectrum. The proposed work was to carry out a feasibility study that will pick out all gamma ray peaks and other features such as Compton edges, bremsstrahlung, presence/absence of shielding and presence of neutrons and escape peaks. Ultimately success of this feasibility study will allow us to collectively explain identified features and form a realistic scenario that produced a given spectrum in the future. We wanted to develop and demonstrate machine learning algorithms that will qualitatively enhance the automated identification capabilities of portable radiological sensors that are currently being used in the field.« less

Final Technical Report for Grant DE-FG02-04ER54795

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merlino, Robert L

This is the final technical report for DOE Grant #DE-FG02-04ER54795-Experimental Investigations of Fundamental Processes in Dusty Plasmas. A plasma is an ionized gas, and a dusty plasmas is a plasma that contains, in addition to electrons and ions, micron-sized dust particles. The dust particles acquire and electric charge in the plasma by collecting electrons and ions. The electrons move more rapidly than the ions, so the dust charge is negative. A 1 micron dust particle in a typical low temperature plasma has a charge corresponding to approximately 2000 electrons. Dusty plasmas are naturally found in astrophysical plasmas, planetary rings, technologicalmore » plasmas, and magnetic fusion plasmas. The goal of this project was to study in the laboratory, the basic physical processes that occur in dusty plasmas. This report provides a summary of the major scientific products and activities of this award.« less

A Pilot Research Project to Determine the Feasibility of Developing Health Related Occupations Curricula at Nicolet College and Technical Institute. Final Report.

ERIC Educational Resources Information Center

Maney, Thomas J.; Boyd, Linda

Personal interviews with each employer of health care workers in the Nicolet Vocational, Technical and Adult Education (VTAE) District were conducted to determine: (1) the extent of need for trained health occupations personnel in the district; (2) the projected need for such personnel in the future; (3) which specific health occupations currently…

Final Report Feasibility Study for the California Wave Energy Test Center (CalWavesm)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blakeslee, Samuel Norman; Toman, William I.; Williams, Richard B.

The California Wave Energy Test Center (CalWave) Feasibility Study project was funded over multiple phases by the Department of Energy to perform an interdisciplinary feasibility assessment to analyze the engineering, permitting, and stakeholder requirements to establish an open water, fully energetic, grid connected, wave energy test center off the coast of California for the purposes of advancing U.S. wave energy research, development, and testing capabilities. Work under this grant included wave energy resource characterization, grid impact and interconnection requirements, port infrastructure and maritime industry capability/suitability to accommodate the industry at research, demonstration and commercial scale, and macro and micro sitingmore » considerations. CalWave Phase I performed a macro-siting and down-selection process focusing on two potential test sites in California: Humboldt Bay and Vandenberg Air Force Base. This work resulted in the Vandenberg Air Force Base site being chosen as the most favorable site based on a peer reviewed criteria matrix. CalWave Phase II focused on four siting location alternatives along the Vandenberg Air Force Base coastline and culminated with a final siting down-selection. Key outcomes from this work include completion of preliminary engineering and systems integration work, a robust turnkey cost estimate, shoreside and subsea hazards assessment, storm wave analysis, lessons learned reports from several maritime disciplines, test center benchmarking as compared to existing international test sites, analysis of existing applicable environmental literature, the completion of a preliminary regulatory, permitting and licensing roadmap, robust interaction and engagement with state and federal regulatory agency personnel and local stakeholders, and the population of a Draft Federal Energy Regulatory Commission (FERC) Preliminary Application Document (PAD). Analysis of existing offshore oil and gas infrastructure was also

Project T.E.A.M. (Technical Education Advancement Modules). Final Report.

ERIC Educational Resources Information Center

Greenville Technical Coll., SC.

Project TEAM (Technical Education Advancement Modules), a cooperative demonstration program for high technology training, created an introductory technical training program and a consumer education package emphasizing the benefits of technical training. The curriculum and training focus of the project began with an assessment of employee needs in…

Final priority. Rehabilitation Training: Job-Driven Vocational Rehabilitation Technical Assistance Center. Final priority.

PubMed

2014-08-19

The Assistant Secretary for Special Education and Rehabilitative Services announces a priority under the Rehabilitation Training program to establish a Job-Driven Vocational Rehabilitation Technical Assistance Center (JDVRTAC). The Assistant Secretary may use this priority for competitions in fiscal year (FY) 2014 and later years. We take this action to focus on training in an area of national need. Specifically, this priority responds to the Presidential Memorandum to Federal agencies directing them to take action to address job-driven training for the Nation's workers. The JDVRTAC will provide technical assistance (TA) to State vocational rehabilitation (VR) agencies to help them develop for individuals with disabilities training and employment opportunities that meet the needs of today's employers.

Final priority; Technical Assistance on State Data Collection--IDEA Data Management Center. Final priority.

PubMed

2014-08-05

The Assistant Secretary for the Office of Special Education and Rehabilitative Services (OSERS) announces a priority under the Technical Assistance on State Data Collection program. The Assistant Secretary may use this priority for competitions in fiscal year (FY) 2014 and later years. We take this action to fund a cooperative agreement to establish and operate an IDEA Data Management Center (Center) that will provide technical assistance (TA) to improve the capacity of States to meet the data collection requirements of the Individuals with Disabilities Education Act (IDEA).

77 FR 46306 - Fluxapyroxad; Pesticide Tolerances Technical Amendment

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-03

...; Pesticide Tolerances Technical Amendment AGENCY: Environmental Protection Agency (EPA). ACTION: Final rule; technical amendment. SUMMARY: EPA issued a final rule in the Federal Register of May 14, 2012, concerning.... Inadvertently, the terminology for the oilseed crop group and for dried plums was incorrect. This technical...

Scout fourth stage attitude and velocity control (AVC) system feasibility study

NASA Technical Reports Server (NTRS)

Byars, L. B.

1975-01-01

The feasibility of incorporating a guidance system in the Scout fourth stage to achieve a significant improvement in expected payload delivery accuracy is studied. The technical investigations included the determination of the AVC equipment performance requirements, establishment of qualification and acceptance test levels, generation of layouts illustrating design approaches for the upper D and payload transition sections to incorporate the hardware, and the preparation of a vendor bid package. Correction concepts, utilizing inertial velocity and attitude, were identified and evaluated. Fourth stage attitude adjustments as determined from inertial velocity variation through the first three stages and a final velocity correction based upon the measured in-plane component errors at injection were employed. Results show radical reductions in apogee-perigee deviations.

Greenhouse gas reduction by recovery and utilization of landfill methane and CO{sub 2} technical and market feasibility study, Boului Landfill, Bucharest, Romania. Final report, September 30, 1997--September 19, 1998

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cook, W.J.; Brown, W.R.; Siwajek, L.

1998-09-01

The project is a landfill gas to energy project rated at about 4 megawatts (electric) at startup, increasing to 8 megawatts over time. The project site is Boului Landfill, near Bucharest, Romania. The project improves regional air quality, reduces emission of greenhouse gases, controls and utilizes landfill methane, and supplies electric power to the local grid. The technical and economic feasibility of pre-treating Boului landfill gas with Acrion`s new landfill gas cleanup technology prior to combustion for power production us attractive. Acrion`s gas treatment provides several benefits to the currently structured electric generation project: (1) increase energy density of landfillmore » gas from about 500 Btu/ft{sup 3} to about 750 Btu/ft{sup 3}; (2) remove contaminants from landfill gas to prolong engine life and reduce maintenance;; (3) recover carbon dioxide from landfill gas for Romanian markets; and (4) reduce emission of greenhouse gases methane and carbon dioxide. Greenhouse gas emissions reduction attributable to successful implementation of the landfill gas to electric project, with commercial liquid CO{sub 2} recovery, is estimated to be 53 million metric tons of CO{sub 2} equivalent of its 15 year life.« less

DETERMINE THE FEASIBILITY OF DEVELOPING A MODEL DESCRIBING THE FLOW OF OCCUPATIONAL AND ECONOMIC INFORMATION INTO THE SECONDARY VOCATIONAL-TECHNICAL SCHOOL. FINAL REPORT.

ERIC Educational Resources Information Center

SILVERN, LEONARD C.

THE MAJOR OBJECTIVES OF THIS FEASIBILITY STUDY WERE (1) TO IDENTIFY INFORMATION SOURCES WHICH FURNISH OCCUPATIONAL AND ECONOMIC DATA TO SECONDARY SCHOOLS, (2) TO SELECT THOSE SOURCES WHICH ARE BELIEVED TO HAVE A MEASURABLE INFLUENCE ON THE VOCATIONAL CURRICULUM, AND (3) TO CATEGORIZE, RELATE, AND COMBINE OR RESTRUCTURE THOSE SOURCES INTO A…

Cape Blanco wind farm feasibility study

NASA Astrophysics Data System (ADS)

1987-11-01

The Cape Blanco Wind Farm (CBWF) Feasibility Study was undertaken as a prototype for determining the feasibility of proposals for wind energy projects at Northwest sites. It was intended to test for conditions under which wind generation of electricity could be commercially feasible, not by another abstract survey of alternative technologies, but rather through a site-specific, machine-specific analysis of one proposal. Some of the study findings would be most pertinent to the Cape Blanco site - local problems require local solutions. Other findings would be readily applicable to other sites and other machines, and study methodologies would be designed to be modified for appraisal of other proposals. This volume discusses environmental, economic, and technical issues of the Wind Farm.

Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alexander Pigarov

2012-06-05

This is the final report for the Research Grant DE-FG02-08ER54989 'Edge Plasma Simulations in NSTX and CTF: Synergy of Lithium Coating, Non-Diffusive Anomalous Transport and Drifts'. The UCSD group including: A.Yu. Pigarov (PI), S.I. Krasheninnikov and R.D. Smirnov, was working on modeling of the impact of lithium coatings on edge plasma parameters in NSTX with the multi-species multi-fluid code UEDGE. The work was conducted in the following main areas: (i) improvements of UEDGE model for plasma-lithium interactions, (ii) understanding the physics of low-recycling divertor regime in NSTX caused by lithium pumping, (iii) study of synergistic effects with lithium coatings andmore » non-diffusive ballooning-like cross-field transport, (iv) simulation of experimental multi-diagnostic data on edge plasma with lithium pumping in NSTX via self-consistent modeling of D-Li-C plasma with UEDGE, and (v) working-gas balance analysis. The accomplishments in these areas are given in the corresponding subsections in Section 2. Publications and presentations made under the Grant are listed in Section 3.« less

Remedial investigation/feasibility study badger army ammunition plant Baraboo, Wisconsin. Volume 3. Feasibility study report (Final)

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1994-08-01

This Feasibility Study (FS) report for the Badger Army Ammunition Plant (BAAP) in Baraboo, Wisconsin, was prepared by ABB Environmental Services, Inc. (ABB-ES) as a component of Task Order 1 of Contract DAAAl5-91-D-OOO8 with the U.S. Army Environmental Center (USAEC). This report uses the results presented in the Final Remedial Investigation (RI) report (ABB-ES, 1993a) to develop and screen alternatives for remediation of contaminated media at BAAP. The purpose of this FS report is to develop, screen, and evaluate site-specific remedial alternatives to mitigate the impact of site-derived chemicals and ultimately provide protection of human health and the environment. Preferredmore » alternatives for each site are included in this report. Based on previous environmental studies at BAAP, 11 potential hazardous waste sites were ranked according to potential contributions of hazardous chemicals to the environment. These sites were designated as Waste Management Areas because some of the sites contain multiple Solid Waste Management Units (SWMUs). The sites selected to undergo facility assessment and corrective actions are: the Propellant Burning Ground (including Landfill), Deterrent Burning Ground, existing Landfill, Settling Ponds and Spoils Disposal Area, Rocket Paste Area, Oleum Plant and Oleum Plant Pond, Nitroglycerine Pond, old Acid Area, new Acid Area, and Ballistics Pond. The USAEC added an 11th site, the Old Fuel Oil Tank, to the list in October 1989 after discovery of fuel-contaminated soils during excavation of a water line in the vicinity of the old fuel oil tank foundation.« less

An Inquiry into Testing of Information Retrieval Systems. Comparative Systems Laboratory Final Technical Report, Part III: CSL Related Studies.

ERIC Educational Resources Information Center

Zull, Carolyn Gifford, Ed.; And Others

This third volume of the Comparative Systems Laboratory (CSL) Final Technical Report is a collection of relatively independent studies performed on CSL materials. Covered in this document are studies on: (1) properties of files, including a study of the growth rate of a dictionary of index terms as influenced by number of documents in the file and…

An approach to developing independent learning and non-technical skills amongst final year mining engineering students

NASA Astrophysics Data System (ADS)

Knobbs, C. G.; Grayson, D. J.

2012-06-01

There is mounting evidence to show that engineers need more than technical skills to succeed in industry. This paper describes a curriculum innovation in which so-called 'soft' skills, specifically inter-personal and intra-personal skills, were integrated into a final year mining engineering course. The instructional approach was designed to promote independent learning and to develop non-technical skills, essential for students on the threshold of becoming practising engineers. Three psychometric tests were administered at the beginning of the course to make students aware of their own and their classmates' characteristics. Substantial prescribed reading assignments preceded weekly group discussions. Several projects during the course required team work skills and application of content knowledge to real-world contexts. Results obtained from students' reflection papers, assignments related to 'soft' skills and end of course evaluations suggest that students' appreciation of the need for these skills, as well as their own perceived competence, increased during the course. Their ability to function as independent learners also increased.

Technical and economic feasibility of development innovative technological solutions for expansion the adjustment range of high-power CCP

NASA Astrophysics Data System (ADS)

Arakelyan, E. K.; Andryushin, A. V.; Burtsev, S. Y.; Andryushin, K. A.

2017-11-01

The analysis of technical and parametric constraints on the adjustment range of highpower CCP and recommended technological solutions in the technical literature for their elimination. Established that in the conditions of toughening the requirements for economy, reliability and maneuverability on the part of the system operator with the participation of CCP in control the frequency and power in the power system, existing methods do not ensure the fulfillment of these requirements. The current situation in the energy sector — the lack of highly manoeuvrable power equipment leads to the need participate in control of power consumption diagrams for all types of power plants, including CCP, although initially they were intended primarily for basic loads. Large-scale research conducted at the department of Automated control systems of technological processes, showed the possibility of a significant expansion of the adjustment range of CCP when it operating in the condensing mode and in the heating mode. The report presents the main results of these research for example the CCP-450 and CCP-450T. Various technological solutions are considered: when CCP in the condensation mode — the use of bypass steam distribution schemes, the transfer of a part of the steam turbine into a low-steam mode; when CCP operation in the heating mode — bypass steam distribution and the transfer CCP to gas turbine unit — power heating plants mode with the transfer the steam turbine to the motor mode. Data on the evaluation of the technical and economic feasibility of the proposed innovative technological solutions are presented in comparison with the methods used to solve this problem, which are used in practice, such as passing through the failures of the electric load graphs by transferring the CCP to the mode of operation with incomplete equipment. When comparing, both the economics, and the maneuverability and reliability of the equipment are considered.

Technical feasibility, diagnostic yield, and safety of microforceps biopsies during EUS evaluation of pancreatic cystic lesions (with video).

PubMed

Mittal, Chetan; Obuch, Joshua C; Hammad, Hazem; Edmundowicz, Steven A; Wani, Sachin; Shah, Raj J; Brauer, Brian C; Attwell, Augustin R; Kaplan, Jeffrey B; Wagh, Mihir S

2018-05-01

Through-the-needle microforceps are a recent addition to the EUS armamentarium for evaluation of pancreatic cystic lesions (PCLs). The main aim of this study was to assess the technical feasibility, diagnostic yield, and safety of EUS-guided microforceps biopsy for PCLs. Our electronic endoscopy database was queried to identify patients who underwent EUS-guided FNA (EUS-FNA) of PCLs and microforceps biopsies during the same procedure. A biopsy was done on the wall of the cyst with the microforceps through the 19-gauge needle, and cyst fluid was collected for cytology and carcinoembryonic antigen (CEA) levels. Adverse events were recorded per published American Society for Gastrointestinal Endoscopy criteria. Twenty-seven patients underwent EUS-FNA and microforceps biopsy of PCLs from February 2016 to July 2017. Fourteen cysts were located in the pancreatic head and/or uncinate, and 13 were located in the body and/or tail region. Microforceps biopsies were technically successful in all cases and provided a pathology diagnosis in 24 of 27 cases (yield 88.9%). Microforceps biopsies diagnosed mucinous cyst in 9 patients (33.3%), serous cystadenoma in 4 (14.8%), neuroendocrine tumor in 1 (3.7%), and benign and/or inflammatory cyst in 10 (37.1%). In 7 patients (26%), microforceps biopsy results drastically changed the diagnosis, providing diagnoses otherwise not suggested by cytology or cyst fluid CEA levels. However, cytology provided a diagnosis of mucinous cyst in 4 cases (14.8%) not detected by microforceps biopsies. No adverse events were noted. Microforceps biopsies were associated with high technical success, and an excellent safety profile and may be a useful adjunctive tool, complementing existing EUS-FNA sampling protocols for PCLs. Copyright © 2018 American Society for Gastrointestinal Endoscopy. Published by Elsevier Inc. All rights reserved.

Development of superior asphalt recycling agents. Phase 1, Technical feasibility. Final technical progress report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bullin, J.A.; Davison, R.R.; Glover, C.J.

1997-07-01

After an introduction and a literature survey in Chap. 1, Chap. 2 describes the tasks, together with objectives and important results obtained for each task throughout the entire project. Chaps. 3 thru 7 detail work in developing a qualitative and quantitative knowledge of asphalt oxidation, composition dependence of asphalt properties, and guidelines for producing superior asphalt binders through composition control. They also detail the development of a kinetic model for asphalt oxidative aging and present an understanding of the composition dependence of asphalt oxidation as well as other performance-related properties. Chaps. 8 and 9 compare the aging performance of recycledmore » blends produced using commercial recycling agents and industrial supercritical fractions as rejuvenating agents. Oxidative aging of the recycled blends were evaluated along with the performance of the recycled blends in terms of the strategic highway research program performance grading procedure. Chap. 10 summarizes the work completed in the areas of processing schemes development, projection updates, and scale-up and commercialization plans.« less

Feasibility of multi-sector policy measures that create activity-friendly environments for children: results of a Delphi study.

PubMed

Aarts, Marie-Jeanne; Schuit, Albertine J; van de Goor, Ien Am; van Oers, Hans Am

2011-12-15

Although multi-sector policy is a promising strategy to create environments that stimulate physical activity among children, little is known about the feasibility of such a multi-sector policy approach. The aims of this study were: to identify a set of tangible (multi-sector) policy measures at the local level that address environmental characteristics related to physical activity among children; and to assess the feasibility of these measures, as perceived by local policy makers. In four Dutch municipalities, a Delphi study was conducted among local policy makers of different policy sectors (public health, sports, youth and education, spatial planning/public space, traffic and transportation, and safety). In the first Delphi round, respondents generated a list of possible policy measures addressing three environmental correlates of physical activity among children (social cohesion, accessibility of facilities, and traffic safety). In the second Delphi round, policy makers weighted different feasibility aspects (political feasibility, cultural/community acceptability, technical feasibility, cost feasibility, and legal feasibility) and assessed the feasibility of the policy measures derived from the first round. The third Delphi round was aimed at reaching consensus by feedback of group results. Finally, one overall feasibility score was calculated for each policy measure. Cultural/community acceptability, political feasibility, and cost feasibility were considered most important feasibility aspects. The Delphi studies yielded 16 feasible policy measures aimed at physical and social environmental correlates of physical activity among children. Less drastic policy measures were considered more feasible, whereas environmental policy measures were considered less feasible. This study showed that the Delphi technique can be a useful tool in reaching consensus about feasible multi-sector policy measures. The study yielded several feasible policy measures aimed at

Feasibility Study for an Automated Library System. Final Report.

ERIC Educational Resources Information Center

Beaumont and Associates, Inc.

This study was initiated by the Newfoundland Public Library Services (NPLS) to assess the feasibility of automation for the library services and to determine the viability of an integrated automated library system for the NPLS. The study addresses the needs of NPLS in terms of library automation; benefits to be achieved through the introduction of…

Studying the Cost and Value of Library Services: Final Report. Technical Report APLAB/94-3/1,2,3,4.

ERIC Educational Resources Information Center

Kantor, Paul B.; And Others

This is the final technical report (in three parts) of a 15-month long project to study the costs and value of library functions at five major research libraries. Twenty-one services or service aspects were studied, and numerous measures of the importance or benefit of the service to the users were made. These measures were studied together to lay…

Feasibility assessment of chemical testing for drug impairment : final report

DOT National Transportation Integrated Search

1985-09-27

An evaluation was made of existing data on concentrations of marijuana, secobarbital, diazepam, diphenhydramine, and methaqualone in blood, saliva and urine to assess the feasibility of establishing chemical teats for detecting drug-impaired driving....

Cape Lookout National Seashore passenger ferry transportation feasibility study

DOT National Transportation Integrated Search

2010-09-01

The Cape Lookout National Seashore Passenger Ferry Transportation Feasibility Study is a technical study documenting the capital investment and operational considerations associated with consolidation of passenger ferry service from Harkers Island an...

NATO Scientific and Technical Information Service (NSTIS): functional description. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Molholm, K.N.; Blados, W.N.; Bulca, C.

1987-08-01

This report provides a functional description of the requirements for a NATO Scientific and Technical Information Service (NSTIS). The user requirements and much of the background information in this report were derived primarily from interviews with more than 60 NATO Headquarters staff members between 2 March and 25 March 1987. In addition, representatives of the Supreme Headquarters Applied Powers Europe (SHAPE) Technical Centre (STC), the Supreme Allied Commander Atlantic (Anti-Submarine Warfare Research) Centre (SACLANTCEN), the NATO Communications and Information Systems Agency (NACISA), The Advisory Group for Aerospace Research and Development (AGARD), the U.S. Defense Technical Information Center (DTIC), and themore » Technical Documentation Center for the Armed Forces in the Netherlands (TDCK), were interviewed, either in person or by telephone.« less

Programs of Study as a State Policy Mandate: A Longitudinal Study of the South Carolina Personal Pathways to Success Initiative. Final Technical Report: Major Findings and Implications

ERIC Educational Resources Information Center

Hammond, Cathy; Drew, Sam F.; Withington, Cairen; Griffith, Cathy; Swiger, Caroline M.; Mobley, Catherine; Sharp, Julia L.; Stringfield, Samuel C.; Stipanovic, Natalie; Daugherty, Lindsay

2013-01-01

This is the final technical report from the National Research Center for Career and Technical Education's (NRCCTE's) five-year longitudinal study of South Carolina's Personal Pathway to Success initiative, which was authorized by the state's Education and Economic Development Act (EEDA) in 2005. NRCCTE-affiliated researchers at the National…

Technical Assistance Program: Off to a Running Start (Newsletter)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This newsletter describes key activities of the DOE Office of Indian Energy Policy and Programs for Winter 2012. Between December 2, 2011, and January 15, 2012, 46 American Indian and Alaska Native Tribes submitted applications to receive technical assistance through the program, which provides Tribes with on-the-ground technical support from DOE and National Renewable Energy Laboratory (NREL) staff to help move tribal energy efficiency and renewable energy projects forward. The applications are being considered through the Strategic Technical Assistance Response Team (START) selection process, which incorporates expert reviews and outreach to Tribes who present a need for assistance with theirmore » community-based energy efficiency and renewable energy projects. The final successful applicants will be selected based on the clarity of their requests for technical assistance and the ability of START to successfully work with each unique project or community. At least three selected Tribes in Alaska will receive technical assistance between March and May 2012, and up to five selected Tribes in the contiguous United States will receive technical assistance between March and August 2012. During the months of START Program activity, DOE and NREL experts will work in the two locations. In Alaska, START experts will work directly with community-based project teams to analyze local energy issues and provide assistance with energy projects and cost savings initiatives. This effort will be bolstered by DOE-IE's partnership with the Denali Commission, which will provide further assistance and expertise. In the lower 48 states, NREL experts will work with the selected renewable energy START projects to evaluate financial and technical feasibility and provide early development technical assistance to better position the projects for financing and construction. This on-the-ground technical assistance is part of a broader DOE-IE effort to make reliable, accurate technical

Technical assumption for Mo-99 production in the MARIA reactor. Feasibility study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jaroszewicz, J.; Pytel, K.; Dabkowski, L.

2008-07-15

The main objective of U-235 irradiation is to obtain the Tc-99m isotope which is widely used in the domain of medical diagnostics. The decisive factor determining its availability, despite its short life time, is a reaction of radioactive decay of Mo-99 into Tc- 99m. One of the possible sources of molybdenum can be achieved in course of the U-235 fission reaction. The paper presents activities and the calculations results obtained upon the feasibility study on irradiation of U-235 targets for production of molybdenum in the MARIA reactor. The activities including technical assumption were focused on performing calculation for modelling ofmore » the target and irradiation device as well as adequate equipment and tools for processing in reactor. It has been assumed that the basic component of fuel charge is an aluminium cladded plate with dimensions of 40x230x1.45 containing 4.7 g U-235. The presumed mode of the heat removal generated in the fuel charge of the reactor primary cooling circuit influences the construction of installation to be used for irradiation and the technological instrumentation. The outer channel construction for irradiation has to be identical as the standard fuel channel construction of the MARIA reactor. It enables to use the existing slab and reactor mounting sockets for the fastening of the molybdenum channel as well as the cooling water delivery system. The measurement of water temperature cooling a fuel charge and control of water flow rate in the channel can also be carried out be means of the standard instrumentation of the reactor. (author)« less

Feasibility study: Atmospheric general circulation experiment, volume 2

NASA Technical Reports Server (NTRS)

Homsey, R. J. (Editor)

1981-01-01

The feasibility analysis of the atmospheric general circulation experiment (AGCE) are documented. The analysis performed in each technical area, the rationale and substantiation for the design approaches selected for the hardware, and the design details for the baseline AGCE are presented.

7 CFR 614.7 - Preliminary technical determinations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 6 2010-01-01 2010-01-01 false Preliminary technical determinations. 614.7 Section... Preliminary technical determinations. (a) A preliminary technical determination becomes final 30 days after... purpose of gathering additional information and discussing the facts relating to the preliminary technical...

Feasibility of utilizing shredded tires in roadside ditches : final report.

DOT National Transportation Integrated Search

1994-06-01

This study was undertaken to examine the feasibility of utilizing shredded tires in hazardous roadside ditches. The concept behind this examination is primarily twofold. First, Louisiana has many miles of rural two lane highway with little or no shou...

Final Report - Wind and Hydro Energy Feasibility Study - June 2011

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jim Zoellick; Richard Engel; Rubin Garcia

2011-06-17

This feasibility examined two of the Yurok Tribe's most promising renewable energy resources, wind and hydro, to provide the Tribe detailed, site specific information that will result in a comprehensive business plan sufficient to implement a favorable renewable energy project.

Feasibility of space disposal of radioactive nuclear waste. 2: Technical summary

NASA Technical Reports Server (NTRS)

1974-01-01

The feasibility of transporting radioactive waste produced in the process of generating electricity in nuclear powerplants into space for ultimate disposal was investigated at the request of the AEC as a NASA in-house effort. The investigation is part of a broad AEC study of methods for long-term storage or disposal of radioactive waste. The results of the study indicate that transporting specific radioactive wastes, particularly the actinides with very long half-lives, into space using the space shuttle/tug as the launch system, appears feasible from the engineering and safety viewpoints. The space transportation costs for ejecting the actinides out of the solar system would represent less than a 5-percent increase in the average consumer's electric bill.

Feasibility and safety of augmented reality-assisted urological surgery using smartglass.

PubMed

Borgmann, H; Rodríguez Socarrás, M; Salem, J; Tsaur, I; Gomez Rivas, J; Barret, E; Tortolero, L

2017-06-01

To assess the feasibility, safety and usefulness of augmented reality-assisted urological surgery using smartglass (SG). Seven urological surgeons (3 board urologists and 4 urology residents) performed augmented reality-assisted urological surgery using SG for 10 different types of operations and a total of 31 urological operations. Feasibility was assessed using technical metadata (number of photographs taken/number of videos recorded/video time recorded) and structured interviews with the urologists on their use of SG. Safety was evaluated by recording complications and grading according to the Clavien-Dindo classification. Usefulness of SG for urological surgery was queried in structured interviews and in a survey. The implementation of SG use during urological surgery was feasible with no intrinsic (technical defect) or extrinsic (inability to control the SG function) obstacles being observed. SG use was safe as no grade 3-5 complications occurred for the series of 31 urological surgeries of different complexities. Technical applications of SG included taking photographs/recording videos for teaching and documentation, hands-free teleconsultation, reviewing patients' medical records and images and searching the internet for health information. Overall usefulness of SG for urological surgery was rated as very high by 43 % and high by 29 % of surgeons. Augmented reality-assisted urological surgery using SG is both feasible and safe and also provides several useful functions for urological surgeons. Further developments and investigations are required in the near future to harvest the great potential of this exciting technology for urological surgery.

A Revision of Technical Mathematics Based on the NCTM Standards. Final Report.

ERIC Educational Resources Information Center

Near, Barbara

Between 1993 and 1996, Henry Ford Community College (Michigan) worked with business, industry, and technical instructors to revise their Technical Mathematics program in accordance with the National Council of Teachers of Mathematics (NCTM) Standards. The purpose of the project was to restructure the technical math curriculum and create a context…

Entrained-flow gasification at elevated pressure: Volume 1: Final technical report, March 1, 1985-April 30,1987

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hedman, P.O.; Smoot, L.D.; Smith, P.J.

1987-10-15

The general purpose of this research program was to develop a basic understanding of the physical and chemical processes in entrained coal gasification and to use the results to improve and evaluate an entrained gasification computer model. The first task included the collection and analysis of in-situ gasifier data at elevated pressures with three coal types (North Dakota lignite, Wyoming subbituminous and Illinois bituminous), the design, construction, and testing of new coal/oxygen/steam injectors with a fourth coal type (Utah bituminous), the collection of supporting turbulent fluid dynamic (LDV) data from cold-flow studies, and the investigation of the feasibility of usingmore » laser-based (CARS) daignostic instruments to make measurements in coal flames. The second task included improvements to the two-dimensional gasifier submodels, tabulation and evaluation of new coal devolatilization and char oxidation data for predictions, fundamental studies of turbulent particle dispersion, the development of improved numerical methods, and validation of the comprehensive model through comparison of predictions with experimental results. The third task was to transfer technical advances to industry and to METC through technical seminars, production of a detailed data book, code placement, and publication of results. Research results for these three tasks are summarized briefly here and presented in detail in the body of the report and in supporting references. 202 refs., 73 figs., 23 tabs.« less

Pipeline bottoming cycle study. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-06-01

The technical and economic feasibility of applying bottoming cycles to the prime movers that drive the compressors of natural gas pipelines was studied. These bottoming cycles convert some of the waste heat from the exhaust gas of the prime movers into shaft power and conserve gas. Three typical compressor station sites were selected, each on a different pipeline. Although the prime movers were different, they were similar enough in exhaust gas flow rate and temperature that a single bottoming cycle system could be designed, with some modifications, for all three sites. Preliminary design included selection of the bottoming cycle workingmore » fluid, optimization of the cycle, and design of the components, such as turbine, vapor generator and condensers. Installation drawings were made and hardware and installation costs were estimated. The results of the economic assessment of retrofitting bottoming cycle systems on the three selected sites indicated that profitability was strongly dependent upon the site-specific installation costs, how the energy was used and the yearly utilization of the apparatus. The study indicated that the bottoming cycles are a competitive investment alternative for certain applications for the pipeline industry. Bottoming cycles are technically feasible. It was concluded that proper design and operating practices would reduce the environmental and safety hazards to acceptable levels. The amount of gas that could be saved through the year 2000 by the adoption of bottoming cycles for two different supply projections was estimated as from 0.296 trillion ft/sup 3/ for a low supply projection to 0.734 trillion ft/sup 3/ for a high supply projection. The potential market for bottoming cycle equipment for the two supply projections varied from 170 to 500 units of varying size. Finally, a demonstration program plan was developed.« less

Canine ovariectomy by hybrid or total natural orifice transluminal endoscopic surgery: technical feasibility study and pain assessment.

PubMed

Linhares, Marcella Teixeira; Feranti, João Pedro Scussel; Coradini, Gabriela Pesamosca; Martins, Letícia Reginato; Martins, Arthur Rodrigues; Sarturi, Vanessa Zanchi; Gavioli, Felipe Baldissarella; Machado Silva, Marco Augusto; de Ataíde, Michelli Westphal; Teixeira, Luciana Gonçalves; Brun, Maurício Veloso

2018-06-13

To compare technical feasibility, surgical time, surgical complications, and postoperative pain in ovariectomy (OVE) by hybrid and total natural orifice transluminal endoscopic surgery (NOTES). Prospective randomized clinical trial. Sixteen healthy and sexually intact bitches. Dogs were randomly assigned to the hybrid NOTES group (HNG; n = 8) and the total NOTES group (TNG; n = 8) to compare surgical time, pain scores and complications. Pain was assessed by using the visual analog scale (VAS) and the Melbourne pain scale (MPS). Surgical time did not differ between the experimental groups (HNG = 46.3 ± 18.5 minutes, TNG = 54.6 ± 31.1 minutes). Exteriorization of the ovaries through the vaginal wound was the major difficulty. Complications were minor in both groups and occurred intraoperatively only in the HNG, and in both groups post operatively. No dogs required rescue analgesia in the intraoperative or postoperative period. There were no differences in VAS or MPS scores between the groups for any surgical times except for the VAS assessment at 72 hours after extubation (HNG = 1.1 ± 0.3, TNG = 0.7 ± 0.4, P = .0221). Both NOTES techniques were comparable for canine OVE, with no requirement for additional analgesia in the postoperative periods. It was not possible to determine whether there was a clear advantage of one technique rather than the other. The minimally invasive techniques proposed for laparoscopic OVE are feasible for dogs with low pain scores and low rates of complications for both groups. © 2018 The American College of Veterinary Surgeons.

Feasibility study report: Area of Contamination (AOC) 43J. (Fort Devens, Groups 2 and 7 sites). Final feasibility study report

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-06-06

The U.S. Army Environmental Center directed ABB Environmental Services, Inc. (ABB-ES), under Contract No. DAAA15-91-D-0008, to conduct a Remedial Investigation (RI) and Feasibility Study (FS) to address the contamination of soil and groundwater at Area of Contamination (AOC) 43J at Fort Devens, Massachusetts. This FS Report is prepared as part of the FS process in accordance with the 1988 U.S. Environmental Protection Agency (USEPA) guidance document entitled Guidance for Conducting Remedial Investigations and Feasibility Studies under CERCLA. The purpose of the FS Report is to initially identify and screen potentially feasible alternatives to control human health and environmental risks atmore » AOC 43J. Following this screening, the FS Report presents a detailed analysis and comparative analysis of the retained alternatives.« less

Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Held, Isaac; V. Balaji; Fueglistaler, Stephan

We have constructed and analyzed a series of idealized models of tropical convection interacting with large-scale circulations, with 25-50km resolution and with 1-2km cloud resolving resolution to set the stage for rigorous tests of convection closure schemes in high resolution global climate models. Much of the focus has been on the climatology of tropical cyclogenesis in rotating systems and the related problem of the spontaneous aggregation of convection in non-rotating systems. The PI (Held) will be delivering the honorary Bjerknes lecture at the Fall 2016 AGU meeting in December on this work. We have also provided new analyses of long-standingmore » issues related to the interaction between convection and the large-scale circulation: Kelvin waves in the upper troposphere and lower stratosphere, water vapor transport into the stratosphere, and upper tropospheric temperature trends. The results of these analyses help to improve our understanding of processes, and provide tests for future high resolution global modeling. Our final goal of testing new convections schemes in next-generation global atmospheric models at GFDL has been left for future work due to the complexity of the idealized model results meant as tests for these models uncovered in this work and to computational resource limitations. 11 papers have been published with support from this grant, 2 are in review, and another major summary paper is in preparation.« less

Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alexander Fridman

2005-06-01

This DOE project DE-FC36-04GO14052 ''Plasma Pilot Plant Test for Treating VOC Emissions from Wood Products Plants'' was conducted by Drexel University in cooperation with Georgia-Pacific (G-P) and Kurchatov Institute (KI). The objective of this project was to test the Plasma Pilot Plant capabilities in wood industry. The final goal of the project was to replace the current state-of-the-art, regenerative thermal oxidation (RTO) technology by Low-Temperature Plasma Technology (LTPT) in paper and wood industry for Volatile Organic Components (VOC) destruction in High Volume Low Concentration (HVLC) vent emissions. MetPro Corporation joined the team as an industrial partner from the environmental controlmore » business and a potential leader for commercialization. Concurrent Technology Corporation (CTC) has a separate contract with DOE for this technology evaluation. They prepared questionnaires for comparison of this technology and RTO, and made this comparison. These data are presented in this report along with the description of the technology itself. Experiments with the pilot plant were performed with average plasma power up to 3.6 kW. Different design of the laboratory and pilot plant pulsed coronas, as well as different analytical methods revealed many new peculiarities of the VOC abatement process. The work reported herein describes the experimental results for the VOCs removal efficiency with respect to energy consumption, residence time, water effect and initial concentration.« less

Vermont Technical Education Commission Report.

ERIC Educational Resources Information Center

Vermont State Technical Education Commission, Montpelier.

A 1968 New England Regional Commission grant to the Vermont Department of Administration financed a feasibility study for a technical college at the postsecondary level. The commission undertook two specific studies: an examination of ultimate career destinations of Vermont secondary students and a survey of Vermont industry to determine immediate…

Statistical Methods and Tools for Uxo Characterization (SERDP Final Technical Report)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pulsipher, Brent A.; Gilbert, Richard O.; Wilson, John E.

2004-11-15

The Strategic Environmental Research and Development Program (SERDP) issued a statement of need for FY01 titled Statistical Sampling for Unexploded Ordnance (UXO) Site Characterization that solicited proposals to develop statistically valid sampling protocols for cost-effective, practical, and reliable investigation of sites contaminated with UXO; protocols that could be validated through subsequent field demonstrations. The SERDP goal was the development of a sampling strategy for which a fraction of the site is initially surveyed by geophysical detectors to confidently identify clean areas and subsections (target areas, TAs) that had elevated densities of anomalous geophysical detector readings that could indicate the presencemore » of UXO. More detailed surveys could then be conducted to search the identified TAs for UXO. SERDP funded three projects: those proposed by the Pacific Northwest National Laboratory (PNNL) (SERDP Project No. UXO 1199), Sandia National Laboratory (SNL), and Oak Ridge National Laboratory (ORNL). The projects were closely coordinated to minimize duplication of effort and facilitate use of shared algorithms where feasible. This final report for PNNL Project 1199 describes the methods developed by PNNL to address SERDP's statement-of-need for the development of statistically-based geophysical survey methods for sites where 100% surveys are unattainable or cost prohibitive.« less

Computer Programs for Technical Communicators: The Compelling Curriculum. Working Draft.

ERIC Educational Resources Information Center

Selfe, Cynthia L.; Wahlstrom, Billie J.

A series of computer programs have been developed at Michigan Technological University for use with technical writing and technical communications classes. The first type of program in the series, CURIE II, includes process-based modules, each of which corresponds to one of the following assignments: memoranda, resumes, feasibility reports,…

Laser Technician Associate Degree Program. A Proposal Submitted to Wisconsin State Board of Vocational, Technical, and Adult Education. (Curriculum Development.) Final Report.

ERIC Educational Resources Information Center

North Central Technical Inst., Wausau, WI.

This final report contains the program proposal with supporting data for developing curriculum materials for and implementing an associate-degree laser technology program at the North Central Technical Institute. The proposal outline provides this information: (1) objectives for the program designed to prepare a technician to safely operate,…

Feasibility of Cosmic-Ray Muon Intensity Measurements for Tunnel Detection

DTIC Science & Technology

1990-06-01

BUR-’TR-3110 TECHNICAL REPORT BRL-TR-3110 mBRL I• FEASIBILITY OF COSMIC - RAY MUON INTENSITY MEASUREMENTS FOR TUNNEL DETECTION AIVARS CELIN. , JUNE...Feasibility of Cosmic - Ray Muon Intensity Measurements f or Tunnel Detection 612786H20001 4.AUTNOR(S) Aivars Celmins 7. PERORMING ORGANIZATION NAMe(S) AND... cosmic - ray muon intensity depends on the amount, of material above the point of reference and is therefore influenced by anomalies in rock density

A feasibility study of orbiter flight control experiments

NASA Technical Reports Server (NTRS)

Geissler, W. H.

1978-01-01

The results of a feasibility study of orbiter flight control experiments performed are summarized. Feasibility studies were performed on a group of 14 experiments selected from a candidate list of 35 submitted to the study contractor by the flight control community. Concepts and requirements were developed for the 14 selected experiments and they were ranked on a basis of technical value, feasibility, and cost. It was concluded that all the selected experiments can be considered as potential candidates for the Orbiter Experiment program, which is being formulated for the Orbiter Flight Tests and subsequent operational flights, regardless of the relative ranking established during the study. None of the selected experiments has significant safety implications and the cost of most was estimated to be less than $200K.

Partial Withdrawal and Final Rule for Nonroad Technical Amendments

EPA Pesticide Factsheets

Amendments to the technical hardship provisions under the Transition Program for Equipment Manufacturers related to the Tier 4 standards for nonroad diesel engines, and to the replacement engine exemption generally applicable to new nonroad engines.

Organic Waste Diversion in Columbia, South Carolina, Feasibility Study

EPA Science Inventory

The study found that a variety of methods are technically and economically feasible for diverting food wastes and providing a positive return on investment for the source. Potential barriers and considerations for food waste diversion are identified in the study. Given the E...

Head Start Impact Study. Technical Report

ERIC Educational Resources Information Center

Puma, Michael; Bell, Stephen; Cook, Ronna; Heid, Camilla; Shapiro, Gary; Broene, Pam; Jenkins, Frank; Fletcher, Philip; Quinn, Liz; Friedman, Janet; Ciarico, Janet; Rohacek, Monica; Adams, Gina; Spier, Elizabeth

2010-01-01

This Technical Report is designed to provide technical detail to support the analysis and findings presented in the "Head Start Impact Study Final Report" (U.S. Department of Health and Human Services, January 2010). Chapter 1 provides an overview of the Head Start Impact Study and its findings. Chapter 2 provides technical information on the…

Feasibility Study of a Novel Thoraco-abdominal Aortic Hybrid Device (SPIDER-graft) in a Translational Pig Model.

PubMed

Debus, Eike S; Kölbel, Tilo; Duprée, Anna; Daum, Günter; Sandhu, Harleen K; Manzoni, Daniel; Wipper, Sabine H

2018-02-01

The hybrid SPIDER-graft consists of a proximal descending aortic stent graft and a conventional six branched Dacron graft for open abdominal aortic repair. Technical feasibility with regard to avoiding thoracotomy and extracorporeal circulation (ECC) during thoraco-abdominal aortic hybrid repair and peri-procedural safety of this novel device are unknown. This was a feasibility and safety study in domestic pigs (75-85 kg). The abdominal aorta including iliac bifurcation, left renal artery, and visceral arteries were exposed via retroperitoneal access. The right iliac branch was first temporarily anastomosed end to side to the distal aorta via partial clamping. During inflow reduction and infra-coeliac cross-clamping, the coeliac trunk (CT) was divided and the proximal stent graft portion of the SPIDER-graft was deployed into the descending aorta via the CT ostium. Retrograde visceral and antegrade aorto-iliac blood flow was maintained via the iliac side branch. The visceral, renal, and iliac arteries were sequentially anastomosed, finally replacing the first iliac end to side anastomosis. Technical success, blood flow, periods of ischaemia, and peri-procedural complications were evaluated after intra-operative completion angiography and post-operative computed tomography angiography. Six animals underwent successful thoracic stent graft deployment and distal open reconstruction without peri-operative death. The median thoracic graft implantation time was 4.5 min, and the median ischaemia times before reperfusion were 10 min for the CT, 8 min for the superior mesenteric artery, 13 min for the right renal artery, and 22 min for the left renal artery. Angiography demonstrated appropriate graft implantation and blood flow measurements confirmed sufficient blood flow through all side branches. In this translational pig model, thoraco-abdominal hybrid repair using the novel SPIDER-graft was successful in avoiding thoracotomy and ECC. Technical feasibility and

78 FR 77563 - Technical Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-24

... NATIONAL CREDIT UNION ADMINISTRATION 12 CFR Parts 700, 701, and 704 RIN 3133-AE33 Technical Amendments AGENCY: National Credit Union Administration (NCUA). ACTION: Final rule. SUMMARY: The NCUA Board... credit unions. The technical amendments conform the regulations to a recent policy change adopted by the...

Technical/commercial feasibility study of the production of fuel-grade ethanol from corn: 100-million-gallon-per-year production facility in Myrtle Grove, Louisiana

NASA Astrophysics Data System (ADS)

1982-05-01

The technical and economic feasibility of producing motor fuel alcohol from corn in a 100 million gallon per year plant to be constructed in Myrtle Grove, Louisiana is evaluated. The evaluation includes a detailed process design using proven technology, a capital cost estimate for the plant, a detailed analysis of the annual operating cost, a market study, a socioeconomic, environmental, health and safety analysis, and a complete financial analysis. Several other considerations for production of ethanol were evaluated including: cogeneration and fuel to be used in firing the boilers; single by-products vs. multiple by-products; and use of boiler flue gas for by-product drying.

Feasibility assessment of chemical testing for drug impairment : final summary report

DOT National Transportation Integrated Search

1985-09-27

An evaluation was made of existing data on concentrations of marijuana, secobarbital, diazepam, diphenhydramine, and methaqualone in blood, saliva and urine to assess the feasibility of establishing chemical tests for police use in detecting drug-imp...

Vertebral artery origin stent placement with distal protection: technical and clinical results.

PubMed

Qureshi, A I; Kirmani, J F; Harris-Lane, P; Divani, A A; Ahmed, S; Ebrihimi, A; Al Kawi, A; Janjua, N

2006-05-01

To report the feasibility, safety, and 1-month results of performing stent placement for vertebral origin stenosis with the use of a distal protection device. Distal protection devices have been shown to reduce the number of cerebral emboli and subsequent ischemic events when used as adjuncts to percutaneous carotid intervention; however, one case of the use of a distal protection device for vertebral artery has been reported in the literature. We retrospectively determined rates of technical success and 1-month stroke or death associated with stent placement by using distal protection (Filter EX; Boston Scientific, Natick, Mass) in patients with symptomatic vertebral artery origin stenosis. Technical success was defined as successful deployment of distal protection device and stent at target lesion followed by successful retrieval of the device and a final residual stenosis of less than 30%. Other outcomes ascertained included any stroke, death, and semiquantitative assessment of particulate material retained by the filter device. The mean age of the 12 treated patients was 68 years (range, 52-88 years) and the group included 9 men and 3 women. The mean percentage of vertebral artery origin stenosis was 71 +/- 6%. Femoral and radial approaches were used in 9 and 3 cases, respectively. Technical success was achieved in 11 of the 12 patients in whom distal protection device placement was attempted. Postprocedure residual stenosis was 5 +/- 4%. Eight devices held macroscopically visible embolic debris (large and small amounts in 3 and 5 devices, respectively). No stroke or death was observed in the 1-month follow-up. The present study demonstrates the feasibility of performing stent placement for vertebral artery origin stenosis by using a distal protection device. Further studies are required to determine the effectiveness of this approach for vertebral artery origin atherosclerosis.

Feasibility of developing a portable driver performance data acquisition system for human factors research: Technical tasks. Volume 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carter, R.J.; Barickman, F.S.; Spelt, P.F.

1998-01-01

A two-phase, multi-year research program entitled ``development of a portable driver performance data acquisition system for human factors research`` was recently completed. The primary objective of the project was to develop a portable data acquisition system for crash avoidance research (DASCAR) that will allow drive performance data to be collected using a large variety of vehicle types and that would be capable of being installed on a given vehicle type within a relatively short-time frame. During phase 1 a feasibility study for designing and fabricating DASCAR was conducted. In phase 2 of the research DASCAR was actually developed and validated.more » This technical memorandum documents the results from the feasibility study. It is subdivided into three volumes. Volume one (this report) addresses the last five items in the phase 1 research and the first issue in the second phase of the project. Volumes two and three present the related appendices, and the design specifications developed for DASCAR respectively. The six tasks were oriented toward: identifying parameters and measures; identifying analysis tools and methods; identifying measurement techniques and state-of-the-art hardware and software; developing design requirements and specifications; determining the cost of one or more copies of the proposed data acquisition system; and designing a development plan and constructing DASCAR. This report also covers: the background to the program; the requirements for the project; micro camera testing; heat load calculations for the DASCAR instrumentation package in automobile trunks; phase 2 of the research; the DASCAR hardware and software delivered to the National Highway Traffic Safety Administration; and crash avoidance problems that can be addressed by DASCAR.« less

Non-technical skills assessment in surgery.

PubMed

Sharma, Bharat; Mishra, Amit; Aggarwal, Rajesh; Grantcharov, Teodor P

2011-09-01

Adverse events in surgery have highlighted the importance of non-technical skills, such as communication, decision-making, teamwork, situational awareness and leadership, to effective organizational performance. These skills carry particular importance to surgical oncology, as members of a multidisciplinary team must work cohesively to formulate effective patient care plans. Several non-technical skills evaluation tools have been developed for use in surgery, without adequate comparison and consensus on which should be standard for training. Eleven articles describing the use of three non-technical evaluation tools related to surgery: NOTSS (Non Technical Skills for Surgeons), NOTECHS (Non Technical Skills) and OTAS (Observational Teamwork Assessment for Surgery) were analyzed with respect to scale formulation, validity, reliability and feasibility. Furthermore, their use in training thus far and the future of non-technical rating scales in surgical curricula was discussed. Future work should focus on incorporating these assessment tools into training and into a real operating room setting to provide formative evaluations for surgical residents. Copyright © 2010 Elsevier Ltd. All rights reserved.

Water reuse in the Apatlaco River Basin (México): a feasibility study.

PubMed

Moeller-Chávez, G; Seguí-Amórtegui, L; Alfranca-Burriel, O; Escalante-Estrada, V; Pozo-Román, F; Rivas-Hernández, A

2004-01-01

The aim of this work is to determine the technical and economic feasibility of implementing different reclamation and reuse projects that improve the quality of the Apatlaco river basin located in the central part of Mexico. A special methodology based on a decision support system was developed. This methodology allows to decide if it is convenient or not to finance a reclamation or reuse project for the most common water uses in the basin. This methodology is based on the net present value criteria (NPV) of the effective cash flow during the useful life of the project. The results obtained reveal a technical and economical feasibility for industrial reuse in Jiutepec and for agricultural reuse in Zacatepec and Emiliano Zapata. On the other hand, sanitation projects are not feasible in all cases analyzed. Therefore, Mexican Regulation (Ley Federal de Derechos en Materia de Agua) as currently implemented, does not promote and support this kind of projects.

Technical Assistance for Southwest Solar Technologies Inc. Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Munoz-Ramos, Karina; Brainard, James Robert; McIntyre, Annie

2012-07-01

Southwest Solar Technologies Inc. is constructing a Solar-Fuel Hybrid Turbine energy system. This innovative energy system combines solar thermal energy with compressed air energy storage and natural gas fuel backup capability to provide firm, non-intermittent power. In addition, the energy system will have very little impact on the environment since, unlike other Concentrated Solar Power (CSP) technologies, it requires minimal water. In 2008 Southwest Solar Technologies received a Solar America Showcase award from the Department of Energy for Technical Assistance from Sandia National Laboratories. This report details the work performed as part of the Solar America Showcase award for Southwestmore » Solar Technologies. After many meetings and visits between Sandia National Labs and Southwest Solar Technologies, several tasks were identified as part of the Technical Assistance and the analysis and results for these are included here.« less

Nonenhanced MR angiography of the pulmonary arteries using single-shot radial quiescent-interval slice-selective (QISS): a technical feasibility study.

PubMed

Edelman, Robert R; Silvers, Robert I; Thakrar, Kiran H; Metzl, Mark D; Nazari, Jose; Giri, Shivraman; Koktzoglou, Ioannis

2017-06-30

For evaluation of the pulmonary arteries in patients suspected of pulmonary embolism, CT angiography (CTA) is the first-line imaging test with contrast-enhanced MR angiography (CEMRA) a potential alternative. Disadvantages of CTA include exposure to ionizing radiation and an iodinated contrast agent, while CEMRA is sensitive to respiratory motion and requires a gadolinium-based contrast agent. The primary goal of our technical feasibility study was to evaluate pulmonary arterial conspicuity using breath-hold and free-breathing implementations of a recently-developed nonenhanced approach, single-shot radial quiescent-interval slice-selective (QISS) MRA. Breath-hold and free-breathing, navigator-gated versions of radial QISS MRA were evaluated at 1.5 Tesla in three healthy subjects and 11 patients without pulmonary embolism or arterial occlusion by CTA. Images were scored by three readers for conspicuity of the pulmonary arteries through the level of the segmental branches. In addition, one patient with pulmonary embolism was imaged. Scan time for a 54-slice acquisition spanning the pulmonary arteries was less than 2 minutes for breath-hold QISS, and less than 3.4 min using free-breathing QISS. Pulmonary artery branches through the segmental level were conspicuous with either approach. Free-breathing scans showed only mild blurring compared with breath-hold scans. For both readers, less than 1% of pulmonary arterial segments were rated as "not seen" for breath-hold and navigator-gated QISS, respectively. In subjects with atrial fibrillation, single-shot radial QISS consistently depicted the pulmonary artery branches, whereas navigator-gated 3D balanced steady-state free precession showed motion artifacts. In one patient with pulmonary embolism, radial QISS demonstrated central pulmonary emboli comparably to CEMRA and CTA. The thrombi were highly conspicuous on radial QISS images, but appeared subtle and were not prospectively identified on scout images acquired

A prototype single-port device for pressurized intraperitoneal aerosol chemotherapy. Technical feasibility and local drug distribution.

PubMed

Seitenfus, Rafael; Ferreira, Paulo Roberto Walter; Santos, Gabriel Oliveira Dos; Alves, Rafael José Vargas; Kalil, Antonio Nocchi; Barros, Eduardo Dipp de; Glehen, Olivier; Casagrande, Thaís Andrade Costa; Bonin, Eduardo Aimoré; Silva Junior, Edison Martins da

2017-12-01

To evaluate the technical feasibility and homogeneity of drug distribution of pressurized intraperitoneal aerosol chemotherapy (PIPAC) based on a novel process of intraperitoneal drug application (multidirectional aerosolization). This was an in vivo experimental study in pigs. A single-port device was manufactured at the smallest diameter possible for multidirectional aerosolization of the chemotherapeutic drug under positive intraperitoneal pressure. Four domestic pigs were used in the study, one control animal that received multidirectional microjets of 9 mL/sec for 30 min and three animals that received multidirectional aerosolization (pig 02: 9 mL/sec for 30 min; pigs 03 and 04: 3 mL/sec for 15 min). Aerosolized silver nitrate solution was applied for anatomopathological evaluation of intraperitoneal drug distribution. Injection time was able to maintain the pneumoperitoneum pressure below 20 mmHg. The rate of moderate silver nitrate staining was 45.4% for pig 01, 36.3% for pig 02, 36.3% for pig 03, and 72.7% for pig 04. Intra-abdominal drug distribution had a broad pattern, especially in animals exposed to the drug for 30 min. Our sample of only four animals was not large enough to demonstrate an association between aerosolization and a higher silver nitrate concentration in the stained abdominal regions.

Technical Feasibility Evaluation on The Use of A Peltier Thermoelectric Module to Recover Automobile Exhaust Heat

NASA Astrophysics Data System (ADS)

Sugiartha, N.; Sastra Negara, P.

2018-01-01

A thermoelectric module composes of integrated p-n semiconductors as hot and cold side junctions and uses Seebeck effect between them to function as a thermoelectric generator (TEG) to directly convert heat into electrical power. Exhaust heat from engines as otherwise wasted to the atmosphere is one of the heat sources freely available to drive the TEG. This paper evaluates technical feasibility on the use of a Peltier thermoelectric module for energy recovery application of such kind of waste heat. An experimental apparatus has been setup to simulate real conditions of automobile engine exhaust piping system. It includes a square section aluminium ducting, an aluminium fin heat sink and a TEC1 12706 thermoelectric module. A heater and a cooling fan are employed to simulate hot exhaust gas and ambient air flows, respectively. Electrical loading is controlled by resistors. Dependent variables measured during the test are cold and hot side temperatures, open and loaded circuit output voltages and electrical current. The test results revealed a promising application of the Peltier thermoelectric module for the engine exhaust heat recovery, though the loaded output power produced and loaded output voltage are still far lower than the commercially thermoelectric module originally purposed for the TEG application.

Technical proficiency in cytopathology: assessment through external quality assurance.

PubMed

Cummings, M C; Greaves, J; Shukor, R A; Perkins, G; Ross, J

2017-04-01

To assess both the feasibility and value of conducting an external quality assurance programme concerning technical aspects of cytopathology laboratory practice, and the interest by laboratories in enrolling in such a programme. Six technical surveys, comprising staining exercises and questionnaires relating to laboratory practice, were distributed over a 4-year period to the approximately 220 laboratories enrolled in the RCPAQAP Cytopathology slide survey modules. Staining exercises using the Papanicolaou and Romanowsky techniques, the preparation of urine and body fluid specimens and immunocytochemistry on the cell block material were assessed. Accompanying relevant questionnaires were included, and one survey comprised a questionnaire alone concerning the collection of urinary tract and body fluid samples. Provision of an external cytopathology technical module was feasible for the RCPAQAP and participation rates (maximum of 87% per survey; average 68% for stained slides and 66% for questionnaires) were commendable, particularly considering these were optional undertakings with some exercises not applicable to all laboratories. The great majority of submitted slides were scored as satisfactory, and there was an especially high standard for the immunocytochemical staining exercise with 95% considered satisfactory, including 50.6% with a perfect score. Reasons for suboptimal scores were provided for potential quality improvement for interested laboratories. A wealth of information relating to laboratory practice was provided to the RCPAQAP which was collated and summarised for laboratory use. The provision of a technical module in cytopathology is both a feasible and valuable undertaking of interest to laboratories which should become standard practice for cytopathology external quality assurance providers. © 2016 John Wiley & Sons Ltd.

Feasibility Study for Low Drag Acoustic Liners Final Report

NASA Technical Reports Server (NTRS)

Riedel, Brian; Wu, Jackie

2017-01-01

This report documents the design and structural analysis as a final deliverable for the Phase 1 contract activity. Also included is a community noise test plan, which is a key deliverable for Phase 2. Finally, a high-level estimate (Phase 3 deliverable) is provided for the work statement of Phases 2-4, which covers the build of two inlet test articles, planning and execution of a flight test with the test inlets, as well as data analysis and final documentation. The two test inlets will be compared to the production baseline inlet configuration. There is also a plan to test one of the inlets "hardwalled" using speed tape or some other similar tape to block the acoustic perforations.

New Jersey Technical Assistance Project (N.J. TAP): "Educational Resources and Support Services on Behalf of Children with Multiple Sensory Impairment." Final Report.

ERIC Educational Resources Information Center

New Jersey State Dept. of Education, Trenton.

This final report describes activities and accomplishments of the New Jersey Technical Assistance Project, a project to improve educational resources and support services for students with multiple sensory impairment (deaf-blindness). Activities and accomplishments are presented in a tabular format for each project goal and objective. The project…

Vessel electrification feasibility study for the New York state canals.

DOT National Transportation Integrated Search

2013-10-01

The objective of this study was to determine the technical and economic feasibility of repowering a diesel-fueled : New York State Canal Corporation (NYSCC) work boat with a diesel hybrid-electric or full-electric powertrain. : The project team instr...

Feasibility of a Modified Chloramine Process for the Production of UDMH and MMH

DTIC Science & Technology

1978-08-31

that phase is provided in this report . Amine Fuels Production Feasibility Demonstration, MCR -75-466, Final Report and Addendurn I - Data Book, Martin ...Final Report , Martin Marietta Corporation, Denver (February 1976) Contract F04701-74-C-0039. Amine Fuels Production Feasibility Demonstration, MCF-75...466, CDRL A305, Volume I, Final Report ; Volume II Economic Analyses; and Volume III, Data Book; Martin Marietta Corporation, Denver (October 1976

Geothermal space/water heating for City of Mammoth Lakes, California. Draft final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sims, A.V.; Racine, W.C.

1977-09-01

The results of a study to determine the technical, economic and environmental feasibility of geothermal district heating for Mammoth Lakes Village, California are presented. The geothermal district heating system selected is technically feasible and uses existing technology in its design and operation. During a preliminary environmental assessment, no potential adverse environmental impacts could be identified of sufficient consequence to preclude the construction and operation of the proposed district heating system. A follow-on program aimed at implementing district heating in Mammoth is outlined.

Technical and economic feasibility of integrated video service by satellite

NASA Technical Reports Server (NTRS)

Price, K. M.; Kwan, R. K.; White, L. W.; Garlow, R. K.; Henderson, T. R.

1992-01-01

A feasibility study is presented of utilizing modern satellite technology, or more advanced technology, to create a cost-effective, user-friendly, integrated video service, which can provide videophone, video conference, or other equivalent wideband service on demand. A system is described that permits a user to select a desired audience and establish the required links similar to arranging a teleconference by phone. Attention is given to video standards, video traffic scenarios, satellite system architecture, and user costs.

Feasibility study ASCS remote sensing/compliance determination system

NASA Technical Reports Server (NTRS)

Duggan, I. E.; Minter, T. C., Jr.; Moore, B. H.; Nosworthy, C. T.

1973-01-01

A short-term technical study was performed by the MSC Earth Observations Division to determine the feasibility of the proposed Agricultural Stabilization and Conservation Service Automatic Remote Sensing/Compliance Determination System. For the study, the term automatic was interpreted as applying to an automated remote-sensing system that includes data acquisition, processing, and management.

Final Technical/Scientific Report: Commodity Scale Thermostable Enzymatic Transformations

DOE Office of Scientific and Technical Information (OSTI.GOV)

James J. Lalonde; Brian Davison

2003-08-30

The conversion of corn starch to high fructose corn-syrup sweetener is a commodity process, producing over 3 billion kg/y. In the last step of the process, an enzyme catalyst is used to convert glucose to the much sweeter sugar fructose. Due to incomplete conversion in the last step, the syrup must be purified using a chromatographic separation technique, which results in equal quantities of water being added to the syrup, and finally the water must be evaporated (up to 1 lb of water/lb of syrup). We have estimated the energy requirement in the evaporation step to be on the ordermore » of 13 billion BTU's/y. This process inefficiency could be eliminated if a thermostable form of glucose isomerase (GI), the enzyme catalyst used in the final step, was developed. Our chosen strategy was to develop an immobilized form of the enzyme in which the protein is first crystallized and then chemically cross-linked to form an insoluble particle. This so-called cross-linked enzyme crystal (CLE C(reg. sign)) technology had been shown to be a powerful method for enzyme stabilization for several other protein catalysts. In this work we have developed more than 30 CLEC preparations of glucose isomerase and tested them for activity and stability. We found these preparations to be highly active, with a 10-50 fold rate per gram of catalyst increase over existing commercial catalysts. The initial rates were also higher at higher temperatures as expected, however the efficiency of the CLEC GI preparations unexpectedly rapidly decreased to a low constant value with use at the higher temperatures. At this point, the source of this activity loss is unclear, however during this loss, the catalyst is found to form a solid mass indicating either breakage of the chemical cross-links or simple aggregation of the particles. It is likely that the increased mass transfer resistance due to this agglomeration is a major component of the activity loss. This research suggests that one potentially

Professional Personnel Evaluation System: 1983-84 Final Technical Report.

ERIC Educational Resources Information Center

Doss, David A.

This technical report summarizes the evaluation ratings given to professionals on probation or up for contract renewal in the Austin Independent School District. Graphs, tables, and rankings are presented for each specified population: all district teachers combined; teachers by school level (elementary, junior high, senior high); teachers by…

High School Graduation Minimum Competency Requirements. Final Technical Report.

ERIC Educational Resources Information Center

Austin Independent School District, TX. Office of Research and Evaluation.

This technical report details the testing results and analyses supporting the evaluation findings related to the Austin (Texas) Independent School District (AISD) minimum competency graduation requirements. The graduation competency status of all AISD students in grades 8 to 12 are documented. The report provides additional information on the data…

Modular Radioisotope Thermoelectric Generator (RTG) Program. Final technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-12-31

Section 2.0 of this report summarizes the MOD-RTG reference flight design, and Section 3.0 discusses the Ground Demonstration System design. Multicouple technology development is discussed in Section 4.0, and Section 5.0 lists all published technical papers prepared during the course of the contract.

Lidar systems for measuring visibility : a technical assessment

DOT National Transportation Integrated Search

1974-09-01

A study has been made of the feasibility of using a laser backscatter system (lidar) to measure slant visibility at airports. This report summarizes the present status of lidar from a technical standpoint. Based largely on the results of experimental...

Develop a Comprehensive Technical Training and Data Collection Program for Structural Welders and Fitters: Technical Proposal

DTIC Science & Technology

2006-05-30

implementation Final Report 4 TECHNICAL PLAN AND RESULTS Task 1: Initiate the Project Management System Two senior NGSS production management...1 Technical Plan and Results...Third the system is hosted on a handheld unit which provides the foremen with an efficient daily planning tool. The Pilot System which entails

Automated Training Evaluation (ATE). Final Report.

ERIC Educational Resources Information Center

Charles, John P.; Johnson, Robert M.

The automation of weapons system training presents the potential for significant savings in training costs in terms of manpower, time, and money. The demonstration of the technical feasibility of automated training through the application of advanced digital computer techniques and advanced training techniques is essential before the application…

Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Howe, Gary; Albritton, John; Denton, David

-based gasification at increased efficiency and at significantly lower capital and operating costs than conventional syngas cleanup technologies. However, before the technology can be deemed ready for scale-up to a full commercial-scale demonstration, additional R&D testing is needed at the site to address the following critical technical risks: WDP sorbent stability and performance; Impact of WDP on downstream cleanup and conversion steps; Metallurgy and refractory; Syngas cleanup performance and controllability; Carbon capture performance and additional syngas cleanup The proposed plan to acquire this additional R&D data involves: Operation of the units to achieve an additional 3,000 hours of operation of the system within the performance period, with a target of achieving 1,000 hours of those hours via continuous operation of the entire integrated pre-commercial demonstration system; Rapid turnaround of repairs and/or modifications required as necessary to return any specific unit to operating status with documentation and lessons learned to support technology maturation, and; Proactive performance of maintenance activities during any unplanned outages and if possible while operating.« less

Vocational Curriculum Modification. Teaching Technical Language to Learning Handicapped Students. Project HIRE: A Curriculum Management System for Instructing the Handicapped. Final Report, Volume 1.

ERIC Educational Resources Information Center

Gardner, David C.; And Others

Volume 1 of the final report on Project HIRE reports the design, development, field-testing, and refining of self-instructional packages to teach entry level technical vocabulary to learning handicapped students mainstreamed in vocational programs. Volume 2, a management handbook, reports the methods and findings concerning development of…

NetView technical research

NASA Technical Reports Server (NTRS)

1993-01-01

This is the Final Technical Report for the NetView Technical Research task. This report is prepared in accordance with Contract Data Requirements List (CDRL) item A002. NetView assistance was provided and details are presented under the following headings: NetView Management Systems (NMS) project tasks; WBAFB IBM 3090; WPAFB AMDAHL; WPAFB IBM 3084; Hill AFB; McClellan AFB AMDAHL; McClellan AFB IBM 3090; and Warner-Robins AFB.

Benchmark Analysis of Career and Technical Education in Lenawee County. Final Report.

ERIC Educational Resources Information Center

Hollenbeck, Kevin

The career and technical education (CTE) provided in grades K-12 in the county's vocational-technical center and 12 local public school districts of Lenawee County, Michigan, was benchmarked with respect to its attention to career development. Data were collected from the following sources: structured interviews with a number of key respondents…

Final priority; technical assistance to improve state data capacity--National Technical Assistance Center to improve state capacity to accurately collect and report IDEA data. Final priority.

PubMed

2013-05-20

The Assistant Secretary for Special Education and Rehabilitative Services announces a priority under the Technical Assistance to Improve State Data Capacity program. The Assistant Secretary may use this priority for competitions in fiscal year (FY) 2013 and later years. We take this action to focus attention on an identified national need to provide technical assistance (TA) to States to improve their capacity to meet the data collection and reporting requirements of the Individuals with Disabilities Education Act (IDEA). We intend this priority to establish a TA center to improve State capacity to accurately collect and report IDEA data (Data Center).

Transportation and Greenhouse Gas Emissions Trading. Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steve Winkelman; Tim Hargrave; Christine Vanderlan

1999-10-01

The authors conclude in this report that an upstream system would ensure complete regulatory coverage of transportation sector emissions in an efficient and feasible manner, and as such represents a key component of a national least-cost GHG emissions abatement strategy. The broad coverage provided by an upstream system recommends this approach over vehicle-maker based approaches, which would not cover emissions from heavy-duty vehicles and the aviation, marine and off-road sub-sectors. The on-road fleet approach unfairly and inefficiently burdens vehicle manufacturers with responsibility for emissions that they cannot control. A new vehicles approach would exclude emissions from vehicles on the roadmore » prior to program inception. The hybrid approach faces significant technical and political complications, and it is not clear that the approach would actually change behavior among vehicle makers and users, which is its main purpose. They also note that a trading system would fail to encourage many land use and infrastructure measures that affect VMT growth and GHG emissions. They recommend that this market failure be addressed by complementing the trading system with a program specifically targeting land use- and infrastructure-related activities. A key issue that must be addressed in designing a national GHG control strategy is whether or not it is necessary to guarantee GHG reductions from the transport sector. Neither an upstream system nor a downstream approach would do so, since both would direct capital to the least-cost abatement opportunities wherever they were found. They review two reasons why it may be desirable to force transportation sector reductions: first, that the long-term response to climate change will require reductions in all sectors; and second, the many ancillary benefits associated with transportation-related, and especially VMT-related, emissions reduction activities. If policy makers find it desirable to establish transportation

Robotic selective neck dissection using a gasless postauricular facelift approach for early head and neck cancer: technical feasibility and safety.

PubMed

Tae, Kyung; Ji, Yong Bae; Song, Chang Myeon; Min, Hyun Jung; Kim, Kyung Rae; Park, Chul Won

2013-03-01

Abstract Background: Scarless and minimally invasive surgery is becoming popular in the head and neck area. We have developed a new robotic selective neck dissection procedure for head and neck squamous cell carcinoma (HNSCC) to avoid a long visible lateral neck scar. Here we report on the technical feasibility and safety of our procedure. We prospectively analyzed 4 patients with early HNSCC who underwent transoral robotic surgery (TORS) and concomitant robotic selective neck dissection via a gasless postauricular facelift approach using the da Vinci(®) Surgical System (Intuitive Surgical Inc., Sunnyvale, CA). Of these patients, 3 were male, and 1 was female. The mean age was 59.0±8.8 years. All patients had tongue cancer, with a clinically negative neck. Three patients were T1, and 1 patient was T2. All patients underwent partial glossectomy by TORS and elective robotic selective neck dissection including levels I, II, and III. The robotic selective neck dissection procedure was completed successfully in all patients. The mean operative time was 276±48 minutes. The mean number of lymph nodes removed was 19.3±7.3. Postoperative hematoma and transient marginal nerve palsy occurred in 1 patient each. Cosmetic satisfaction was excellent in all patients. Preliminary results indicate that robotic selective neck dissection via a gasless postauricular facelift approach is feasible and safe and allows for excellent postoperative cosmesis. Further studies are necessary to determine the oncologic safety and surgical completeness of this procedure compared with conventional neck dissection.

Composite Socio-Technical Systems: A Method for Social Energy Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Yingchen; He, Fulin; Hao, Jun

In order to model and study the interactions between social on technical systems, a systemic method, namely the composite socio-technical systems (CSTS), is proposed to incorporate social systems, technical systems and the interaction mechanism between them. A case study on University of Denver (DU) campus grid is presented in paper to demonstrate the application of the proposed method. In the case study, the social system, technical system, and the interaction mechanism are defined and modelled within the framework of CSTS. Distributed and centralized control and management schemes are investigated, respectively, and numerical results verifies the feasibility and performance of themore » proposed composite system method.« less

Tactical and operational response to major incidents: feasibility and reliability of skills assessment using novel virtual environments.

PubMed

Cohen, Daniel; Sevdalis, Nick; Patel, Vishal; Taylor, Michael; Lee, Henry; Vokes, Mick; Heys, Mick; Taylor, David; Batrick, Nicola; Darzi, Ara

2013-07-01

To determine feasibility and reliability of skills assessment in a multi-agency, triple-site major incident response exercise carried out in a virtual world environment. Skills assessment was carried out across three scenarios. The pre-hospital scenario required paramedics to triage and treat casualties at the site of an explosion. Technical skills assessment forms were developed using training syllabus competencies and national guidelines identified by pre-hospital response experts. Non-technical skills were assessed using a seven-point scale previously developed for use by pre-hospital paramedics. The two in-hospital scenarios, focusing on a trauma team leader and a silver/clinical major incident co-ordinator, utilised the validated Trauma-NOTECHS scale to assess five domains of performance. Technical competencies were assessed using an ATLS-style competency scale for the trauma scenario. For the silver scenario, the assessment document was developed using competencies described from a similar role description in a real-life hospital major incident plan. The technical and non-technical performance of all participants was assessed live by two experts in each of the three scenarios and inter-assessor reliability was computed. Participants also self-assessed their performance using identical proformas immediately after the scenarios were completed. Self and expert assessments were correlated (assessment cross-validation). Twenty-three participants underwent all scenarios and assessments. Performance assessments were feasible for both experts as well as the participants. Non-technical performance was generally scored higher than technical performance. Very good inter-rater reliability was obtained between expert raters across all scenarios and both technical and non-technical aspects of performance (reliability range 0.59-0.90, Ps<0.01). Significant positive correlations were found between self and expert assessment in technical skills across all three scenarios

A procedural skills OSCE: assessing technical and non-technical skills of internal medicine residents.

PubMed

Pugh, Debra; Hamstra, Stanley J; Wood, Timothy J; Humphrey-Murto, Susan; Touchie, Claire; Yudkowsky, Rachel; Bordage, Georges

2015-03-01

Internists are required to perform a number of procedures that require mastery of technical and non-technical skills, however, formal assessment of these skills is often lacking. The purpose of this study was to develop, implement, and gather validity evidence for a procedural skills objective structured clinical examination (PS-OSCE) for internal medicine (IM) residents to assess their technical and non-technical skills when performing procedures. Thirty-five first to third-year IM residents participated in a 5-station PS-OSCE, which combined partial task models, standardized patients, and allied health professionals. Formal blueprinting was performed and content experts were used to develop the cases and rating instruments. Examiners underwent a frame-of-reference training session to prepare them for their rater role. Scores were compared by levels of training, experience, and to evaluation data from a non-procedural OSCE (IM-OSCE). Reliability was calculated using Generalizability analyses. Reliabilities for the technical and non-technical scores were 0.68 and 0.76, respectively. Third-year residents scored significantly higher than first-year residents on the technical (73.5 vs. 62.2%) and non-technical (83.2 vs. 75.1%) components of the PS-OSCE (p < 0.05). Residents who had performed the procedures more frequently scored higher on three of the five stations (p < 0.05). There was a moderate disattenuated correlation (r = 0.77) between the IM-OSCE and the technical component of the PS-OSCE scores. The PS-OSCE is a feasible method for assessing multiple competencies related to performing procedures and this study provides validity evidence to support its use as an in-training examination.

Refurbishment of Railroad Crossties : A Technical and Economic Analysis

DOT National Transportation Integrated Search

1977-12-01

An analysis of the principal modes of failure for wooden railroad crossties was conducted and an evaluation of the technical and economic feasibility of refurbishing these ties was conducted. Among the principal modes of structural deterioration, onl...

7 CFR 1737.71 - Interest rate to be considered for the purpose of assessing feasibility for loans.

Code of Federal Regulations, 2011 CFR

2011-01-01

...-year Treasury rate will be used in all feasibility studies for loans with a final maturity of at least... rate used in feasibility studies for loans with final maturities of less than 30 years. (c) The... “date of determination” means the date of the feasibility study used in support of the loan...

Feasibility of mining lunar resources for earth use: Circa 2000 AD. Volume 1: Summary

NASA Technical Reports Server (NTRS)

Nishioka, K.; Arno, R. D.; Alexander, A. D.; Slye, R. E.

1973-01-01

The feasibility of obtaining lunar minerals for terrestrial uses is examined. Preliminary results gave indications that it will not be economically feasible to mine, refine, and transport lunar materials to Earth for consumption. A broad systems approach was used to analyze the problem. It was determined that even though the procedure was not economically advisable, the concept for the operations is technically sound.

Development of Microcomputer Simulations for Vocational/Technical Education. Final Report.

ERIC Educational Resources Information Center

Randolph Technical Coll., Asheboro, NC.

A project investigated the feasibility of developing equipment simulations in vocational curricula using videotapes and microcomputers. To conduct the research, two pieces of equipment that could be used in vocational curricula throughout the North Carolina Community College System were chosen: (1) computer numerical control (CNC) lathe used in…

Evaluating the feasibility of underground coal gasification in Thailand

DOE Office of Scientific and Technical Information (OSTI.GOV)

Young, B.C.; Harju, J.A.; Schmit, C.R.

Underground coal gasification (UCG) is a clean coal technology that converts in situ coal into a low- to medium-grade product gas without the added expense of mining and reclamation. Potential candidates for UCG are those coal resources that are not economically recoverable or that are otherwise unacceptable for conventional coal utilization processes. The Energy and Environmental Research Center (EERC), through the sponsorship of the US Trade and Development Agency and in collaboration with the Electricity Generating Authority of Thailand (EGAT), is undertaking a feasibility study for the application of UCG in the Krabi coal mining area, 620 miles south ofmore » Bangkok in Thailand. The EERC`s objective for this project is to determine the technical, environmental, and economic feasibility of demonstrating and commercializing UCG at a selected site in the Krabi coal mining area. This paper addresses the preliminary developments and ongoing strategy for evaluating the selected UCG site. The technical, environmental, and economic factors for successful UCG operation are discussed, as well as the strategic issues pertaining to future energy expansion in southern Thailand.« less

Vessel Cold-Ironing Using a Barge Mounted PEM Fuel Cell: Project Scoping and Feasibility.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pratt, Joseph William; Harris, Aaron P.

2013-01-01

A barge-mounted hydrogen-fueled proton exchange membrane (PEM) fuel cell system has the potential to reduce emissions and fossil fuel use of maritime vessels in and around ports. This study determines the technical feasibility of this concept and examines specific options on the U.S. West Coast for deployment practicality and potential for commercialization.The conceptual design of the system is found to be straightforward and technically feasible in several configurations corresponding to various power levels and run times.The most technically viable and commercially attractive deployment options were found to be powering container ships at berth at the Port of Tacoma and/or Seattle,more » powering tugs at anchorage near the Port of Oakland, and powering refrigerated containers on-board Hawaiian inter-island transport barges. Other attractive demonstration options were found at the Port of Seattle, the Suisun Bay Reserve Fleet, the California Maritime Academy, and an excursion vessel on the Ohio River.« less

Milan Army Ammunition Plant focused feasibility study for the northern industrial area soil. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Locandro, R.R.; Okusu, N.M.; Case, J.

1995-04-01

ICF Kaiser Engineers (ICF) and Environmental Resources Management (ERM) have been contracted by the US Army Environmental Center (USAEC) to perform a Focused Feasibility Study (FS) for contaminated soil within the northern industrial areas of Milan Army Ammunition Plant (MAAP), Tennessee. The purpose of the Focused FS is to develop and evaluate remedial alternatives such that an appropriate remedy can be selected for the site. The MAAP Remedial Investigation (RI) performed in 1989--1991 confirmed that the O-Line Ponds area, facility drainage ditches that received industrial wastewater, and manufacturing and disposal areas have been sources of groundwater contamination. One finding ofmore » the RI Report was that sufficient information was available concerning the O-Line Ponds area to proceed with a Focused FS. The O-Line Ponds area was further divided into two operable units (OUs): OU1 is the groundwater immediately downgradient of the O-Line Ponds area, and OU2 is the soil, surface water, and sediment at the O-Line Ponds area. A Proposed Plan and Record of Decision (ROD) for OU1 were finalized in 1992, which called for groundwater extraction, treatment, and reinjection of the treated water upgradient of the O-Line Ponds. The design of this system was completed in 1993, and construction of the system is currently underway. For OU2, the Proposed Plan and ROD (finalized in 1993) called for the extension of the existing multi-layered cap to cover the contaminated soil around the perimeter of the existing cap. The design of the cap extension was completed in 1994, and construction will begin in late 1994.« less

76 FR 80226 - Technical Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-23

... final rule, effective upon publication. Generally, the Administrative Procedure Act (APA) requires a.... Additionally, the APA requires that a final rule must have a delayed effective date of 30 days from the date of... delayed effective date requirement under the APA. 5 U.S.C. 553(d)(3). Again the technical change conforms...

Feasibility and coexistence of large ecological communities.

PubMed

Grilli, Jacopo; Adorisio, Matteo; Suweis, Samir; Barabás, György; Banavar, Jayanth R; Allesina, Stefano; Maritan, Amos

2017-02-24

The role of species interactions in controlling the interplay between the stability of ecosystems and their biodiversity is still not well understood. The ability of ecological communities to recover after small perturbations of the species abundances (local asymptotic stability) has been well studied, whereas the likelihood of a community to persist when the conditions change (structural stability) has received much less attention. Our goal is to understand the effects of diversity, interaction strengths and ecological network structure on the volume of parameter space leading to feasible equilibria. We develop a geometrical framework to study the range of conditions necessary for feasible coexistence. We show that feasibility is determined by few quantities describing the interactions, yielding a nontrivial complexity-feasibility relationship. Analysing more than 100 empirical networks, we show that the range of coexistence conditions in mutualistic systems can be analytically predicted. Finally, we characterize the geometric shape of the feasibility domain, thereby identifying the direction of perturbations that are more likely to cause extinctions.

Feasibility and coexistence of large ecological communities

PubMed Central

Grilli, Jacopo; Adorisio, Matteo; Suweis, Samir; Barabás, György; Banavar, Jayanth R.; Allesina, Stefano; Maritan, Amos

2017-01-01

The role of species interactions in controlling the interplay between the stability of ecosystems and their biodiversity is still not well understood. The ability of ecological communities to recover after small perturbations of the species abundances (local asymptotic stability) has been well studied, whereas the likelihood of a community to persist when the conditions change (structural stability) has received much less attention. Our goal is to understand the effects of diversity, interaction strengths and ecological network structure on the volume of parameter space leading to feasible equilibria. We develop a geometrical framework to study the range of conditions necessary for feasible coexistence. We show that feasibility is determined by few quantities describing the interactions, yielding a nontrivial complexity–feasibility relationship. Analysing more than 100 empirical networks, we show that the range of coexistence conditions in mutualistic systems can be analytically predicted. Finally, we characterize the geometric shape of the feasibility domain, thereby identifying the direction of perturbations that are more likely to cause extinctions. PMID:28233768

Final Revisions Rule Significant Contribution Assessment TSD

EPA Pesticide Factsheets

This Technical Support Document (TSD) presents quantitative assessments of the relationship between final revisions to the Transport Rule and the original analysis conducted for the final Transport Rule.

75 FR 15342 - Advisory Committees; Technical Amendment

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-29

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration 21 CFR Part 14 [Docket No. FDA-2010-N-0001] Advisory Committees; Technical Amendment Agency: Food and Drug Administration, HHS. ACTION: Final rule; technical amendment. SUMMARY: The Food and Drug Administration (FDA) is amending its...

Beams from boltwood: a feasibility study

Treesearch

Peter Koch

1964-01-01

Previous papers in this series of four have explored technical aspects of converting southern pine boltwood into long laminated beams of uniform high strength. This final discussion examines production and economic aspects of the proposed system.

Solar pond power plant feasibility study for Davis, California

NASA Technical Reports Server (NTRS)

Wu, Y. C.; Singer, M. J.; Marsh, H. E.; Harris, J.; Walton, A. L.

1982-01-01

The feasibility of constructing a solar pond power plant at Davis, California was studied. Site visits, weather data compilation, soil and water analyses, conceptual system design and analyses, a material and equipment market survey, conceptual site layout, and a preliminary cost estimate were studied. It was concluded that a solar pond power plant is technically feasible, but economically unattractive. The relatively small scale of the proposed plant and the high cost of importing salt resulted in a disproportionately high capital investment with respect to the annual energy production capacity of the plant. Cycle optimization and increased plant size would increase the economical attractiveness of the proposed concept.

Feasible and technical aspects of transcatheter arterial chemoembolization for non-resectable hepatocellular carcinoma using a 3.5-French catheter system.

PubMed

Yagyu, Yukinobu; Tsurusaki, Masakatsu; Kamiyama, Kazutoshi; Kitagaki, Hajime; Murakami, Takamichi

2014-12-01

To evaluate the feasibility and technical aspects of transcatheter arterial chemoembolization (TACE) for non-resectable hepatocellular carcinoma (HCC) using a 3.5-French (Fr) catheter system. This study included 328 consecutive cases of HCC among 232 patients who underwent TACE procedures using both a 3.5-Fr catheter system and a microcatheter fitted to a 3.5-Fr system between April 2009 and November 2011. We assessed the ability to reach the catheter into the proper hepatic artery (PHA), main hepatic branch, segmental artery, and subsegmental or sub-subsegmental artery. The feasibility was rated according to the following factors: (1) the number of arteries that could be used to reach the target artery/total number of procedures using the 3.5-Fr system, (2) the rate of successful completion of the procedures without changing over to the 4-Fr system and (3) the reasons for changing over the 4-Fr system. TACE of the PHA (27 sessions), RHA/LHA (103 sessions), segmental (31 sessions), or subsegmental/sub-subsegmental arteries (162 sessions) was performed. The rate of successfully reaching the target artery using the 3.5-Fr system was 93% (306/328 sessions). We were unable to reach the target artery in 22 sessions, including 11/8/3 procedures targeting the sub-subsegmental artery, subsegmental artery, and RHA/LHA, respectively. We changed over to the 4-Fr system in six sessions; therefore, the rate of successful completion of the procedures without changing over to the 4-Fr system was 98% (322/328 sessions). TACE of the target artery can be successfully performed using the 3.5-Fr system in most patients with HCC.

2012 Technical Corrections Fact Sheet

EPA Pesticide Factsheets

Final Rule: 2012 Technical Corrections, Clarifying and Other Amendments to theGreenhouse Gas Reporting Rule, and Confidentiality Determinations for Certain DataElements of the Fluorinated Gas Source Category

48 CFR 252.235-7011 - Final scientific or technical report.

Code of Federal Regulations, 2014 CFR

2014-10-01

... technical report. 252.235-7011 Section 252.235-7011 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT OF DEFENSE CLAUSES AND FORMS SOLICITATION PROVISIONS AND CONTRACT... of the report; and (c) For submission of reports in other than paper copy, contact the Defense...

48 CFR 252.235-7011 - Final scientific or technical report.

Code of Federal Regulations, 2012 CFR

2012-10-01

... technical report. 252.235-7011 Section 252.235-7011 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT OF DEFENSE CLAUSES AND FORMS SOLICITATION PROVISIONS AND CONTRACT... of the report; and (c) For submission of reports in other than paper copy, contact the Defense...

48 CFR 252.235-7011 - Final scientific or technical report.

Code of Federal Regulations, 2010 CFR

2010-10-01

... technical report. 252.235-7011 Section 252.235-7011 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT OF DEFENSE CLAUSES AND FORMS SOLICITATION PROVISIONS AND CONTRACT... of the report; and (c) For submission of reports in other than paper copy, contact the Defense...

48 CFR 252.235-7011 - Final scientific or technical report.

Code of Federal Regulations, 2011 CFR

2011-10-01

... technical report. 252.235-7011 Section 252.235-7011 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT OF DEFENSE CLAUSES AND FORMS SOLICITATION PROVISIONS AND CONTRACT... of the report; and (c) For submission of reports in other than paper copy, contact the Defense...

48 CFR 252.235-7011 - Final scientific or technical report.

Code of Federal Regulations, 2013 CFR

2013-10-01

... technical report. 252.235-7011 Section 252.235-7011 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT OF DEFENSE CLAUSES AND FORMS SOLICITATION PROVISIONS AND CONTRACT... of the report; and (c) For submission of reports in other than paper copy, contact the Defense...

Job Skills Education Program. Final Technical Report.

ERIC Educational Resources Information Center

Florida State Univ., Tallahassee. Center for Educational Technology.

This publication provides materials developed by a project designed to transfer a U.S. Army computer-based basic skills curriculum to applications in the vocational skills development of civilian adults. An executive summary of the final report describes the Job Skills Education Program (JSEP), which teaches academic skills that support vocational…

Invention and Writing in Technical Work: Representing the Object.

ERIC Educational Resources Information Center

Winsor, Dorothy A.

1994-01-01

Describes the way invention is relevant to the practice of technical writing. Studies three engineering students engaged in a real-world project. Shows how the students' technical work and invention for the final report were simultaneous activities. Claims that invention for and through writing overlaps with technical invention. (HB)

Feasibility Study for Paravetic Competency Development of Vocational Agriculture Teachers. Final Report.

ERIC Educational Resources Information Center

Evans, Donald E.

A study was conducted to determine the feasibility of an animal health (paravetical) competency development inservice program for vocational agriculture teachers in Pennsylvania. Objectives were to identify the paravetic (paraveterinary medical) competencies needed by vocational agriculture teachers to teach high school students and adults via…

Technical Evaluation Motor No. 10 (TEM-10)

NASA Technical Reports Server (NTRS)

1993-01-01

Technical Evaluation Motor No. 10 (TEM-10) was static fired on 27 Apr. 1993 at the Thiokol Corporation full-scale motor static test bay, T-24. This final test report documents the procedures, performance, and results of the static test firing of TEM-10. All observations, discussions, conclusions, and recommendations contained are final. Included is a presentation and discussion of TEM-10 performance, anomalies, and test results in concurrence with the objectives outlined in CTP-0110, Revision D, Space Shuttle Technical Evaluation Motor No. 10 (TEM-10) Static Fire Test Plan.

Final June Revisions Rule Significant Contribution Assessment TSD

EPA Pesticide Factsheets

This Technical Support Document (TSD) presents quantitative assessments of the relationship between the final February revisions to the Transport Rule, the final June revisions rule, and the original analysis conducted for the final Transport Rule.

Feasibility study of a cyclotron complex for hadron therapy

NASA Astrophysics Data System (ADS)

Smirnov, V.; Vorozhtsov, S.

2018-04-01

An accelerator complex for hadron therapy based on a chain of cyclotrons is under development at JINR (Dubna, Russia), and the corresponding conceptual design is under preparation. The complex mainly consists of two superconducting cyclotrons. The first accelerator is a compact cyclotron used as an injector to the main accelerator, which is a six-fold separated sector machine. The facility is intended for generation of protons and carbon beams. The H2+ and 12C6+ ions from the corresponding ECR ion sources are accelerated in the injector-cyclotron up to the output energy of 70 MeV/u. Then, the H2+ ions are extracted from the injector by a stripping foil, and the resulting proton beam with the energy of 70 MeV is used for medical purposes. After acceleration in the main cyclotron, the carbon beam can be either used directly for therapy or introduced to the main cyclotron for obtaining the final energy of 400 MeV/u. The basic requirements to the project are the following: compliance to medical requirements, compact size, feasible design, and high reliability of all systems of the complex. The advantages of the dual cyclotron design can help reaching these goals. The initial calculations show that this design is technically feasible with acceptable beam dynamics. The accelerator complex with a relatively compact size can be a good solution for medical applications. The basic parameters of the facility and detailed investigation of the magnetic system and beam dynamics are described.

Cape Blanco Wind Farm Feasibility Study : Technical Report, No. 2, Civil Engineering.

DOE Office of Scientific and Technical Information (OSTI.GOV)

United States. Bonneville Power Administration.

1986-09-01

An investigation of the feasibility of developing a wind farm near Cape Blanco, Oregon, requires a plan for civil engineering and preliminary site construction activities. In this report, plans for such activities and related cost estimates are presented for a wind farm using either a Boeing MOD-2 or FloWind 170 wind turbine generator.

2005 v4.3 Technical Support Document

EPA Pesticide Factsheets

Emissions Modeling for the Final Mercury and Air Toxics Standards Technical Support Document describes how updated 2005 NEI, version 2 emissions were processed for air quality modeling in support of the final Mercury and Air Toxics Standards (MATS).

Feasibility study for mega-electron-volt electron beam tomography.

PubMed

Hampel, U; Bärtling, Y; Hoppe, D; Kuksanov, N; Fadeev, S; Salimov, R

2012-09-01

Electron beam tomography is a promising imaging modality for the study of fast technical processes. But for many technical objects of interest x rays of several hundreds of keV energy are required to achieve sufficient material penetration. In this article we report on a feasibility study for fast electron beam computed tomography with a 1 MeV electron beam. The experimental setup comprises an electrostatic accelerator with beam optics, transmission target, and a single x-ray detector. We employed an inverse fan-beam tomography approach with radiographic projections being generated from the linearly moving x-ray source. Angular projections were obtained by rotating the object.

A 30/20 GHz FSS feasibility study

NASA Technical Reports Server (NTRS)

1987-01-01

The near term feasibility of direct-to-subscriber services were determined using the 30/20 GHz Fixed Satellite Service (FSS) frequency bands. Those technologies which need to be further developed before such a system can be implemented, were identified. To determine this feasibility, dozens of potential applications were examined for their near-term viability, and the subscriber base of three promising applications were estimated. The system requirements, terminal design, and satellite architecture were all investigated to determine whether a 30/20 GHz FSS system is technically and economically feasible by mid-1990s. It was concluded that such a system is feasible, although maturation of some technologies is needed. This system would likely consist of one or two multibeam satellites serving hub/spoke networks of simple user terminals and more complex, mutli-channel terminals of the service providers. Rain compensation would be accomplished non-adaptively through the use of coding, nonuniform satellite TWT power that is a function of a beam's anticipated downlink fading, and signal regeneration of traffic to the wettest climate regions. It was estimated that a potential market of almost two million users could exist in in the mid-1990s time frame for home banking and financial services via Ka-band satellites.

Electronic document distribution: Design of the anonymous FTP Langley Technical Report Server

NASA Technical Reports Server (NTRS)

Nelson, Michael L.; Gottlich, Gretchen L.

1994-01-01

An experimental electronic dissemination project, the Langley Technical Report Server (LTRS), has been undertaken to determine the feasibility of delivering Langley technical reports directly to the desktops of researchers worldwide. During the first six months, over 4700 accesses occurred and over 2400 technical reports were distributed. This usage indicates the high level of interest that researchers have in performing literature searches and retrieving technical reports at their desktops. The initial system was developed with existing resources and technology. The reports are stored as files on an inexpensive UNIX workstation and are accessible over the Internet. This project will serve as a foundation for ongoing projects at other NASA centers that will allow for greater access to NASA technical reports.

JT9D engine diagnostics. Task 2: Feasibility study of measuring in-service flight loads. [747 aircraft performance

NASA Technical Reports Server (NTRS)

Kafka, P. G.; Skibo, M. A.; White, J. L.

1977-01-01

The feasibility of measuring JT9D propulsion system flight inertia loads on a 747 airplane is studied. Flight loads background is discussed including the current status of 747/JT9D loads knowledge. An instrumentation and test plan is formulated for an airline-owned in-service airplane and the Boeing-owned RA001 test airplane. Technical and cost comparisons are made between these two options. An overall technical feasibility evaluation is made and a cost summary presented. Conclusions and recommendations are presented in regard to using existing inertia loads data versus conducting a flight test to measure inertia loads.

Forecasting the Future Food Service World of Work. Final Report. Volume III. Technical Papers on the Future of the Food Service Industry. Service Management Reports.

ERIC Educational Resources Information Center

Powers, Thomas F., Ed.; Swinton, John R., Ed.

This third and final volume of a study on the future of the food service industry contains the technical papers on which the information in the previous two volumes was based. The papers were written by various members of the Pennsylvania State University departments of economics, food science, nutrition, social psychology, and engineering and by…

Feasibility Study of Improved Methods for Riverbank Stabilization

DTIC Science & Technology

1964-11-01

hose materials which appear to be technically feasible for such applications are listed in Tables I - 1 and I - 2. I-9 Artificial Riprap...the uncompacted asphalt pavement. Those which 1-11 show the most potential for further study are soil cement, synthetic elastomer sheeting, and...uncompated asphalt pavement. Chemical soil stabilization and metal sheeting are too exp~nsive, and the quality of chemically stabilized soil protection is

Direct application of geothermal energy at the L'eggs Product Plant, Las Cruces, New Mexico. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1981-02-01

The study program to determine the feasibility of interfacing a potential geothermal resource of Dona Ana County, New Mexico L'eggs Product industrial process is discussed in this final report. Five separate sites were evaluated initially as to geothermal potential and technical feasibility. Preliminary analysis revealed that three sites were considered normal, but that two sites (about three miles from the L'eggs Plant) had very high shallow subsurface temperature gradients (up to 14.85/sup 0/F/100 ft). An initial engineering analysis showed that to meet the L'eggs plant temperature and energy requirements a geothermal fluid temperature of about 250/sup 0/F and 200 gpmmore » flow rate would be necessary. A brief economic comparison indicated that the L'eggs plant site and a geothermal site approximately four miles from the plant did merit further investigation. Detailed engineering and economic design and analysis of these two sites (including the drilling of an 1873 feet deep temperature gradient test hole at the L'eggs Plant) showed that development of the four mile distant site was technically feasible and was the more economic option. It was determined that a single-stage flash system interface design would be most appropriate for the L'eggs Plant. Approximately 39 billion Btu/yr of fossil fuel could be replaced with geothermal energy at the L'eggs facility for a total installed system cost of slightly over $2 million. The projected economic payback period was calculated to be 9.2 years before taxes. This payback was not considered acceptable by L'eggs Products, Inc., to merit additional design or construction work at this time.« less

A Dissemination Model for New Technical Education Programs. Final Report.

ERIC Educational Resources Information Center

Hull, Daniel M.

The Technical Education Research Center-SW has conceived, tested, and refined a model for disseminating newly developed programs and materials throughout the nation. The model performed successfully in the dissemination of more than 50,000 educational units (modules) of Laser/Electro-Optics Technician (LEOT) materials during a four-year period…

Final report on technical work accomplished under contract NASw-2953

NASA Technical Reports Server (NTRS)

Fredricks, R. W.

1977-01-01

A report is given on the technical work accomplished in the area of plasma physics. The subjects covered are: (1) oblique whistler instabilities, (2) current-limited electron beam injection, (3) three-dimensional ion sound turbulence, (4) theoretical aspects of sounder antenna operation and (5) whistler modes in bow shock structures.

Final Report UCLA-Thermochemical Storage with Anhydrous Ammonia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lavine, Adrienne

challenge associated with storage of gas phase components. 3. While this project is primarily concerned with high-temperature heat recovery and methods to store the gaseous components, it is also important to consider the feasibility of the entire system. Consequently, an additional goal was to perform analysis to show the feasibility of integrating endothermic reactors within a tower receiver. A conceptual design of an ammonia dissociation receiver/reactor has been developed that fits into the same size cylindrical envelope as the molten salt receiver in SAM, and has the same design thermal capacity. The calculated thermal efficiency of this receiver is 94.6%. Thus, this investigation has established the technical feasibility of a surround field tower system using ammonia dissociation. With these challenges addressed, we proceeded to design a full-scale synthesis and heat recovery system. A model was developed and validated by comparison with our experimental data. A parametric study showed, among other things, the importance of using small tube diameters and spacing to enhance heat transfer. Multi-parameter optimization was used to find a design that minimizes the wall material volume. Finally, cost estimation shows that the ammonia system has good prospects of meeting the Sunshot 15(USD)/kWht target: estimated costs of the entire synthesis system for the 220 MWt plant with 6 hours of storage are 13(USD)/kWht using salt cavern storage and 18(USD)/kWht using shaft drilling. Costs per kWht are even lower with more hours of storage. With the established technology of ammonia synthesis as a starting point, the successes of the project have mitigated technical risks associated with high-temperature synthesis reaction, underground storage, and tower receiver design. Estimated costs are less than 15(USD)/kWht with salt cavern storage. It is now possible to map a time line to commercial deployment that is likely to be shorter and less risky than other thermochemical cycles under

Ten bar probe technical summary. [feasibility of outer planet common atmospheric probe

NASA Technical Reports Server (NTRS)

Ellis, T. R.

1974-01-01

The feasibility of an outer planet common atmospheric probe is studied with emphasis on entry heating rates and improved ephemeris. It is concluded that a common probe design is possible except for Jupiter; the basic technology exists except for Jupiter heat shielding. A Mariner class bus provides for better bus science and probe bus communications than a Pioneer class bus.

75 FR 33682 - Export Administration Regulations; Technical Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-15

...-01] RIN 0694-AE93 Export Administration Regulations; Technical Amendments AGENCY: Bureau of Industry... Bureau of Industry and Security (BIS) makes a technical amendment to the Export Administration... review of final decisions and orders issued in BIS export control administrative enforcement proceedings...

Health care fraud and abuse data collection program: technical revisions to Healthcare Integrity and Protection Data Bank data collection activities. Final rule.

PubMed

2004-09-21

The rule finalizes technical changes to the Healthcare Integrity and Protection Data Bank (HIPDB) data collection reporting requirements by clarifying the types of personal numeric identifiers that may be reported to the data bank in connection with adverse actions. The rule clarifies that in lieu of a Social Security Number (SSN), an individual taxpayer identification number (ITIN) may be reported to the data bank when, in those limited situations, an individual does not have an SSN.

Feasibility of Optical Instruments Based on Multiaperture Optics.

DTIC Science & Technology

1984-10-16

system may be configured. The optical elements may be nonimaging concentrators (light horns), the field of view (FOV) of which may be controlled by a...RD-RI58 868 FEASIBILITY OF OPTICAL INSTRUMENTS BASED ON i/I MULTIAPERTURE OPTICS (U) FLORIDA UNIV GAINESVILLE DEPT OF NUCLEAR ENGINEERING SCIENCES J D...d Subtitle) 5. TYPE OF REPORT & PERIOD COVERED ’ 0 Feasibility of Optical Instruments Based on Final Report * CD Multiaperature Optics 615/83 to 9/30

Study on feasible technical potential of coal to electricity in china

NASA Astrophysics Data System (ADS)

Jia, Dexiang; Tan, Xiandong

2017-01-01

The control of bulk coal is one of the important work of air pollution control in China’s future. Existing research mainly focuses on the adaptability, economy, construction and renovation plan, and operation optimization of specific energy substitution utilization, and lacks the strategy research of long-term layout of energy substitution utilization in large area. This paper puts forward a technical potential prediction method of coal to electricity based on the thermal equivalent method, which is based on the characteristics of regional coal consumption, and combined with the trend of adaptability and economy of energy substitution utilization. Also, the paper calculates the comprehensive benefit of coal to electricity according to the varieties of energy consumption and pollutant emission level of unit energy consumption in China’s future. The research result shows that the development technical potential of coal to electricity in China is huge, about 1.8 trillion kWh, including distributed electric heating, heat pump and electric heating boiler, mainly located in North China, East China, and Northeast China. The implementation of coal to electricity has remarkable comprehensive benefits in energy conservation and emission reduction, and improvement of energy consumption safety level. Case study shows the rationality of the proposed method.

Local/State Bilingual Project. 1981-82 Final Technical Report. Appendixes.

ERIC Educational Resources Information Center

Austin Independent School District, TX. Office of Research and Evaluation.

The 1981-82 Local/State Bilingual Program Technical Report addresses the evaluation questions of the Local/State Bilingual Program Evaluation Design. It is organized into six appendixes. Each appendix reports the information collected by a specific measure. Each appendix consists of (1) an instrument description, (2) purpose of the measure, (3)…

Development of German-English Machine Translation System. Final Technical Report.

ERIC Educational Resources Information Center

Lehmann, Winfred P.; Stachowitz, Rolf A.

This report describes work on a pilot system for a fully automatic, high-quality translation of German scientific and technical text into English and gives the results of an experiment designed to show the system's capability to produce quality mechanical translation. The areas considered were: (1) grammar formalism, mainly involving the addition…

77 FR 39623 - Airworthiness Standards: Aircraft Engines; Technical Amendment

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-05

...] Airworthiness Standards: Aircraft Engines; Technical Amendment AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Final rule; technical amendment. SUMMARY: This amendment clarifies aircraft engine... from applicants requesting FAA engine type certifications and aftermarket certifications, such as...

Feasibility study on intersection in North Sumatera

NASA Astrophysics Data System (ADS)

Hastuty, I. P.; Sembiring, I. S.; Anas, R.; Lubis, A. S.

2018-02-01

Traffic congestion is one of the problems faced by big cities, One of them is Binjai city and Medan city in North Sumatera. One of the causes of congestion is intersection of roads with highway and roads with railroads. To ensure the smooth movement of vehicles, technical handling at the intersection is needed. Therefore, it is necessary to pre-study the feasibility of level crossing in Binjai and Medan to be able to assess the investment needs and the level of importance of road development in the region. The development of transportation infrastructure and facilities is based on the thought of improving the transportation network system. The necessity of systemical integrated transportation system handling is needed in creating a transportation efficiency. The purpose of this study is to identify and prioritize the needs of the railway crossings. The objective which we want to be achieved is to obtain a document that contains technical, economic and environmental ability indicators as a reference in the feasibility and planning studies. The methodology used is collecting the primary data, secondary data, introduction of study area as the initial analysis of the problem. From the study it can be concluded that the existence of railway interchange will move the movement through traffic so it will not interfere the movement of traffic within urban areas and it keeps the national road network performance is still good.

Exploration studies technical report, FY1988 status. Volume 1: Technical summary

NASA Technical Reports Server (NTRS)

1988-01-01

The Office of Exploration (OEXP) at NASA Headquarters has been tasked with defining and recommending alternatives for an early 1990's nationaL decision on a focused program of human exploration of the solar system. The Mission Analysis and System Engineering (MASE) group, which is managed by the Exploration Studies Office at the Lyndon B. Johnson Space Center, is responsible for coordinating the technical studies necessary for accomplishing such a task. This technical report, produced by the MASE, describes the process that has been developed in a case study approach. The four case studies developed in FY88 include: (1) Human Expedition to Phobos; (2) Human Expedition to Mars; (3) Lunar Observatory; and (4) Lunar Outpost to Early Mars Evolution. The final outcome of this effort is a set of programmatic and technical conclusions and recommendations for the following year's work.

Systematized contact between inventors and industry. Final technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-07-31

A total of 139 inventions by private (individual) inventors were submitted to Technology Targeting Incorporated. Each inventor was told of the nature of the DOE-supported Project, through informational and promotional efforts by TTI, and each completed an Invention Submittal Form developed by TTI to describe the essential nature of the claimed invention. Many also submitted detailed descriptions, drawings, technical reports and similar supplemental materials giving a more comprehensive view of their inventions. Each invention was reviewed for technical and commercial merit, as well as for appropriateness of marketing through the Technology Targeting DataBase{trademark} (hereafter ``DATABASE). Overall, participating inventors were enthusiasticmore » about the Project and felt participation in it was rewording. Even when not selected for marketing, inventors were given an analysis of their inventions which could help them enhance the inventions and improve marketing efforts. Inventors whose inventions were selected for marketing were shown how to professionally market the inventions, including the format for Non Confidential Invention Summaries, the preferred form for Confidential Disclosure Agreements, targeting of business decision-makers responsible for technology evaluation, and the like; some of these inventors are still interacting with industrial contacts provided by TTI through this Project. All inventors received copies of patent abstracts uncovered in the prior art searches for their inventions and a copy of TTI`s booklet, Patent Law Basics for Individual Inventors.« less

Systematized contact between inventors and industry. [Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-07-31

A total of 139 inventions by private (individual) inventors were submitted to Technology Targeting Incorporated. Each inventor was told of the nature of the DOE-supported Project, through informational and promotional efforts by TTI, and each completed an Invention Submittal Form developed by TTI to describe the essential nature of the claimed invention. Many also submitted detailed descriptions, drawings, technical reports and similar supplemental materials giving a more comprehensive view of their inventions. Each invention was reviewed for technical and commercial merit, as well as for appropriateness of marketing through the Technology Targeting DataBase[trademark] (hereafter DATABASE). Overall, participating inventors were enthusiasticmore » about the Project and felt participation in it was rewording. Even when not selected for marketing, inventors were given an analysis of their inventions which could help them enhance the inventions and improve marketing efforts. Inventors whose inventions were selected for marketing were shown how to professionally market the inventions, including the format for Non Confidential Invention Summaries, the preferred form for Confidential Disclosure Agreements, targeting of business decision-makers responsible for technology evaluation, and the like; some of these inventors are still interacting with industrial contacts provided by TTI through this Project. All inventors received copies of patent abstracts uncovered in the prior art searches for their inventions and a copy of TTI's booklet, Patent Law Basics for Individual Inventors.« less

Sub-marine groundwater for the supply of drinking water. A review of the hydro-geological potential and its technical and economical feasibility.

NASA Astrophysics Data System (ADS)

Haakon Bakken, Tor; Mangset, Lars Erik

2010-05-01

Sub-marine groundwater is water stored in aquifers under the sea-bed and is expected to be present in large quantities on the continental shelf. The proposed utilization of sub-marine groundwater as a new source of drinking water supply is a radical and new idea that has never been fully explored or tested anywhere in the world. In regions where access to raw water of acceptable quality is very limited and desalination of sea water is the only realistic alternative to increase the supply of potable water, utilization of sub-marine groundwater might play a role. A technical concept deemed suitable to the hydrological and geological characteristics of sub-marine water is proposed based on well-proven technology from the off-shore oil & gas sector. A course economic assessment of this concept is conducted based on judgmental cost estimates from experts in the hydro-geological and oil & gas domain. The technical concept uses a jackup or a barge with a modular rig during drilling, while a steel jacket with a modular rig or a sub-sea installation is assumed to be feasible technical solutions during production. The selection of technology will vary from case to case depending on factors such as the local off-shore conditions (wave/wind exposure, drilling depth, distance from shore, etc.), required reliability of supply, access to/availability of technology and financial considerations. A standard reverse osmosis plant is proposed as treatment solution, given the assumed need to desalinate moderately saline water. The costs of each treatment step, as a function of raw water salinity are providing input to the subsequent economical estimates. The proposed treatment solution is assumed being a conservative choice of technology. The costs of producing drinking water from sub-marine groundwater are compared with desalination of sea water, given that this is the only realistic alternative. Based on a systematic risk assessment using the same comparative financial structure and

Virtual rehabilitation in a school setting: is it feasible for children with cerebral palsy?

PubMed

Rosie, Juliet A; Ruhen, Shelley; Hing, Wayne A; Lewis, Gwyn N

2015-01-01

To determine the feasibility of a school-based virtual rehabilitation intervention for children with cerebral palsy. A feasibility study was conducted using a mixed method approach. Participants were five children with cerebral palsy who were currently attending a rural school. Each child received an 8-week rehabilitation programme involving an Interactive Virtual Reality Exercise (IREX) system. The IREX was placed in the child's school for the duration of the intervention. Each child's programme was designed by a physiotherapist but supervised by a teacher aide at the school. Feasibility of the intervention was assessed through a questionnaire completed by the child and an interview conducted with the teacher supervisor. The children all rated the IREX intervention as fun, easy to use, and beneficial for their arm. Categories from the supervisor interviews centred on resolving technical issues, the enjoyment of taking part due to the child's progress, and the central role of interacting with the child. Input from the research physiotherapist was critical to the success of the intervention. The IREX is feasible to implement in a school-based setting supervised by teachers. This provides an option for delivering physiotherapy to children in isolated areas who do not receive on-going therapy. Implication for Rehabilitation Virtual rehabilitation programmes using the IREX are feasible in a school-based setting. The negative impact of technical difficulties is likely to be overcome by the user's enjoyment and rehabilitation benefits gained. Input from a therapist in designing and monitoring the programme is critical.

FINAL TECHNICAL REPORT, U.S. Department of Energy: Award No. DE-EE0002855 "Demonstrating the Commercial Feasibility of Geopressured-Geothermal Power Development at Sweet Lake Field - Cameron Parish, Louisiana"

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gayle, Phillip A., Jr.

The goal of the project was to demonstrate the commercial feasibility of geopressured-geothermal power development by exploiting the extraordinarily high pressured hot brines know to exist at depth near the Sweet Lake oil and gas field in Cameron Parish, Louisiana. The existence of a geopressured-geothermal system at Sweet Lake was confirmed in the 1970's and 1980's as part of DOE's Geopressured-Geothermal Program. That program showed that the energy prices at the time could not support commercial production of the resource. Increased electricity prices and technological advancements over the last two decades, combined with the current national support for developing clean,more » renewable energy and the job creation it would entail, provided the justification necessary to reevaluate the commercial feasibility of power generation from this vast resource.« less

Word Lists to Simplify Vocabulary of Technical Information. Final Report.

ERIC Educational Resources Information Center

Kincaid, J. Peter; And Others

This report describes eight word lists developed for use as part of the computer readability editing system (CRES), which was developed to serve as an author's aid in improving the ease of comprehending Navy technical manuals and training materials. The system has features which flag uncommon and misspelled words and long sentences, suggest simple…

The evaluation of a framework for measuring the non-technical ward round skills of final year nursing students: An observational study.

PubMed

Murray, Kara; McKenzie, Karen; Kelleher, Michael

2016-10-01

The importance of non-technical skills (NTS) to patient outcomes is increasingly being recognised, however, there is limited research into how such skills can be taught and evaluated in student nurses in relation toward rounds. This pilot study describes an evaluation of a NTS framework that could potentially be used to measure ward round skills of student nurses. The study used an observational design. Potential key NTS were identified from existing literature and NTS taxonomies. The proposed framework was then used to evaluate whether the identified NTS were evident in a series of ward round simulations that final year general nursing students undertook as part of their training. Finally, the views of a small group of qualified nurse educators, qualified nurses and general nursing students were sought about whether the identified NTS were important and relevant to practice. The proposed NTS framework included seven categories: Communication, Decision Making, Situational Awareness, Teamwork and Task Management, Student Initiative and Responsiveness to Patient. All were rated as important and relevant to practice. The pilot study suggests that the proposed NTS framework could be used as a means of evaluating student nurse competencies in respect of many non-technical skills required for a successful ward round. Further work is required to establish the validity of the framework in educational settings and to determine the extent to which it is of use in a non-simulated ward round setting. Copyright © 2016 Elsevier Ltd. All rights reserved.

Development and implementation of centralized simulation training: evaluation of feasibility, acceptability and construct validity.

PubMed

Shamim Khan, Mohammad; Ahmed, Kamran; Gavazzi, Andrea; Gohil, Rishma; Thomas, Libby; Poulsen, Johan; Ahmed, Munir; Jaye, Peter; Dasgupta, Prokar

2013-03-01

WHAT'S KNOWN ON THE SUBJECT? AND WHAT DOES THE STUDY ADD?: A competent urologist should not only have effective technical skills, but also other attributes that would make him/her a complete surgeon. These include team-working, communication and decision-making skills. Although evidence for effectiveness of simulation exists for individual simulators, there is a paucity of evidence for utility and effectiveness of these simulators in training programmes that aims to combine technical and non-technical skills training. This article explains the process of development and validation of a centrally coordinated simulation program (Participants - South-East Region Specialist Registrars) under the umbrella of the British Association for Urological Surgeons (BAUS) and the London Deanery. This program incorporated training of both technical (synthetic, animal and virtual reality models) and non-technical skills (simulated operating theatres). To establish the feasibility and acceptability of a centralized, simulation-based training-programme. Simulation is increasingly establishing its role in urological training, with two areas that are relevant to urologists: (i) technical skills and (ii) non-technical skills. For this London Deanery supported pilot Simulation and Technology enhanced Learning Initiative (STeLI) project, we developed a structured multimodal simulation training programme. The programme incorporated: (i) technical skills training using virtual-reality simulators (Uro-mentor and Perc-mentor [Symbionix, Cleveland, OH, USA], Procedicus MIST-Nephrectomy [Mentice, Gothenburg, Sweden] and SEP Robotic simulator [Sim Surgery, Oslo, Norway]); bench-top models (synthetic models for cystocopy, transurethral resection of the prostate, transurethral resection of bladder tumour, ureteroscopy); and a European (Aalborg, Denmark) wet-lab training facility; as well as (ii) non-technical skills/crisis resource management (CRM), using SimMan (Laerdal Medical Ltd, Orpington, UK

Arizona Deafblind Project, 1995-1999. Final Report.

ERIC Educational Resources Information Center

Arizona State School for the Deaf and Blind, Tucson.

This final report describes accomplishments of the four-year federally funded Arizona Deafblind Project which attempted to: (1) identify all deafblind children in Arizona; (2) deliver technical assistance to families; (3) deliver technical assistance to service providers; and (4) enhance community oversight, coordination, and collaboration with…

Solar Living House Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walters, Bradley

mobile or computing device. These systems allow for more precise calibrations of temperature/humidity/lighting to correspond with user needs and preferences, minimizing energy losses with economical night- or day-time setbacks. Solar Dehumidification System: The most significant technological innovation in the Solar Living House is the solar thermal dehumidification system. This system generates hot water through two rooftop-mounted evacuated tube solar thermal collectors. The hot water is used to continually dry a regenerative solid desiccant material, typically white silica gel. The solid desiccant is used to adsorb moisture and humidity from the air without additional mechanical cooling. This strategy allows humidity to be modulated independently of air temperature, providing greater thermal comfort and reducing the opportunity for the growth of mold spores within the house while also reducing the overall energy consumption of the HVAC system. Economic Feasibility: The team set aggressive goals for affordability, targeting a construction cost of $138,710. An independent professional cost estimator determined the overall project costs, as designed, would be $333,799, or $336.15 per square foot of finished floor area. This is more than 2.4 times the target construction cost. By comparison, the average construction cost for a home in the United States in 2015 was $289,415, or $103.29 per square foot of finished floor area. Following work on the Solar Living House, team leaders incorporated many of its objectives into a net-zero energy home on a site in Gainesville, Florida. This site-built home avoided many of the constraints and complications of modular construction necessitated by the Solar Decathlon, allowing it to be built for a much more modest budget. This two-bedroom two bath 1,800 square foot home was constructed for $135.39 per square foot, including active photovoltaic solar systems, careful attention to continuous air barriers, increased insulation levels, and

Polar source analysis : technical memorandum

DOT National Transportation Integrated Search

2017-09-29

The following technical memorandum describes the development, testing and analysis of various polar source data sets. The memorandum also includes recommendation for potential inclusion in future releases of AEDT. This memorandum is the final deliver...

Feasibility of graphene CRLH metamaterial waveguides and leaky wave antennas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chu, Derrick A.; Itoh, Tatsuo; Hon, Philip W. C.

2016-07-07

The feasibility of composite right/left-handed (CRLH) metamaterial waveguides based upon graphene plasmons is demonstrated via numerical simulation. Designs are presented that operate in the terahertz frequency range along with their various dimensions. Dispersion relations, radiative and free-carrier losses, and free-carrier based tunability are characterized. Finally, the radiative characteristics are evaluated, along with its feasibility for use as a leaky-wave antenna. While CRLH waveguides are feasible in the terahertz range, their ultimate utility will require precise nanofabrication, and excellent quality graphene to mitigate free-carrier losses.

Vehicle infrastructure integration proof of concept : technical description--vehicle : final report

DOT National Transportation Integrated Search

2009-05-19

This report provides the technical description of the VII system developed for the Cooperative Agreement VII Program between the USDOT and the VII Consortium. The basic architectural elements are summarized and detailed descriptions of the hardware a...

Final Report Feasibility Study for the California Wave Energy Test Center (CalWavesm) - Volume #2 - Appendices #16-17

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dooher, Brendan; Toman, William I.; Davy, Doug M.

The California Wave Energy Test Center (CalWave) Feasibility Study project was funded over multiple phases by the Department of Energy to perform an interdisciplinary feasibility assessment to analyze the engineering, permitting, and stakeholder requirements to establish an open water, fully energetic, grid connected, wave energy test center off the coast of California for the purposes of advancing U.S. wave energy research, development, and testing capabilities. Work under this grant included wave energy resource characterization, grid impact and interconnection requirements, port infrastructure and maritime industry capability/suitability to accommodate the industry at research, demonstration and commercial scale, and macro and micro sitingmore » considerations. CalWave Phase I performed a macro-siting and down-selection process focusing on two potential test sites in California: Humboldt Bay and Vandenberg Air Force Base. This work resulted in the Vandenberg Air Force Base site being chosen as the most favorable site based on a peer reviewed criteria matrix. CalWave Phase II focused on four siting location alternatives along the Vandenberg Air Force Base coastline and culminated with a final siting down-selection. Key outcomes from this work include completion of preliminary engineering and systems integration work, a robust turnkey cost estimate, shoreside and subsea hazards assessment, storm wave analysis, lessons learned reports from several maritime disciplines, test center benchmarking as compared to existing international test sites, analysis of existing applicable environmental literature, the completion of a preliminary regulatory, permitting and licensing roadmap, robust interaction and engagement with state and federal regulatory agency personnel and local stakeholders, and the population of a Draft Federal Energy Regulatory Commission (FERC) Preliminary Application Document (PAD). Analysis of existing offshore oil and gas infrastructure was also

Feasibility Study of Economics and Performance of Solar Photovoltaics at the Stringfellow Superfund Site in Riverside, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mosey, G.; Van Geet, O.

2010-12-01

This report presents the results of an assessment of the technical and economic feasibility of deploying a photovoltaics (PV) system on the Stringfellow Superfund Site in Riverside, California. The site was assessed for possible PV installations. The cost, performance, and site impacts of different PV options were estimated. The economics of the potential systems were analyzed using an electric rate of $0.13/kWh and incentives offered by Southern California Edison under the California Solar Initiative. According to the assessment, a government-owned, ground-mounted PV system represents a technically and economically feasible option. The report recommends financing options that could assist in themore » implementation of such a system.« less

Teleworking in connection with technical aids for disabled persons.

PubMed

Alimandi, L; Andrich, R; Porqueddu, B

1995-01-01

An experimental teleworking arrangement was established between Milan and Rome in order to evaluate the use of multimedia technology and remote working for improving the service provided by an information and advice centre for the disabled. This activity requires a highly interdisciplinary approach and both clinical and technical expertise. The hypothesis was that offering the lone expert in Rome the possibility of teleconsulting with colleagues in Milan (where the whole range of expertise was available) would provide a comprehensive service for disabled clients asking for advice on technical aids in Rome. The results of an experiment demonstrated the feasibility of such teleworking and allowed a teleconsulting method to be defined that fits the specific needs of the technical-aid information service and improves quality.

Automated water monitor system field demonstration test report. Volume 2: Technical summary

NASA Technical Reports Server (NTRS)

Brooks, R. L.; Jeffers, E. L.; Perreira, J.; Poel, J. D.; Nibley, D.; Nuss, R. H.

1981-01-01

The NASA Automatic Water Monitor System was installed in a water reclamation facility to evaluate the technical and cost feasibility of producing high quality reclaimed water. Data gathered during this field demonstration test are reported.

Development and feasibility of a wearable infant wrist band for the objective measurement of physical activity using accelerometery.

PubMed

Prioreschi, Alessandra; Nappey, Thomas; Westgate, Kate; Olivier, Patrick; Brage, Soren; Micklesfield, Lisa Kim

2018-01-01

It is important to be able to reliably and feasibly measure infant and toddler physical activity in order to determine adherence to current physical activity guidelines and effects on early life development, growth and health. This study aimed to describe the development of an infant wearable wrist-worn band for the measurement of physical activity; to determine the feasibility of the device data for observational measurement of physical activity and to determine the caregiver reported acceptability of the infant wearable wrist band. After various iterations of prototypes and piloting thereof, a final wearable band was designed to fit an Axivity AX3 monitor. Mother and infant/toddler (aged 3-24 months) pairs ( n  = 152) were recruited, and mothers were asked for their child to wear the band with enclosed monitor at all times for 1 week (minimum 3 days). Feasibility was assessed by determining technical reliability of the data, as well as wear time and compliance according to requirements for observational measurement. Acceptability was assessed via questionnaire. Technical reliability of the Axivity AX3 monitors in this age group was good. After excluding days that did not have at least 15 h of wear time, only 2% of participants had less than three valid days of data remaining, and 4% of participants had no data (due to device loss or data loss). Therefore, 94% of participants were compliant, having three or more days of wear with at least 15 h of wear per day, thus providing enough valid data for observational measurement. The majority (60%) of mothers reported being "very happy" with the safety of the device, while only 8% were "a little worried". A large majority (86%) of mothers stated that the band attracted attention from others, although this was mostly attributed to curiosity about the function of the band. Most (80%) of participants rated the comfort of the band as "comfortable", and 10% rated it as "very comfortable". The infant wearable band

NUSC Technical Publications Guide.

DTIC Science & Technology

1985-05-01

Facility personnel especially that of A. Castelluzzo, E. Deland, J. Gesel , and E. Szlosek (all of Code 4343). Reviewed and Approved: 14 July 1980 D...their technical content and format. Review and approve the manual outline, the review manuscript, and the final camera - reproducible copy. Conduct in

Feasibility study of shared-ride auto transit. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kocur, G.; Zaelke, D.; Neumann, L.

1977-09-01

The report examines the feasibility of the implementation of shared-ride auto transit (SRAT), which is an innovative approach for increasing auto occupancy in rural and urban areas. The report focuses on operational concepts, potential usage, legal and regulatory issues, and institutional issues. Formulation of the SRAT concept was motivated by several concerns, such as: (1) energy conservation; (2) transit service to areas unable to economically justify conventional transit services, and to travel disadvantaged groups; (3) transit service replacement to achieve greater efficiency and to reduce transit deficits; (4) provision of inexpensive transit service; and (5) the increase of safety andmore » reliability of hitchhiking. Four case study sites (Boulder, Colorado; Boston, Massachusetts; Portland, Oregon; and Tidewater, Virginia), were used to identify the specific institutional issues likely to impact SRAT implementation for that site, and to identify the opportunities for designing, implementing and operating SRAT in a variety of institutional settings.« less

Feasibility and applications of RFID technologies to support Right-of-Way functions : technical report

DOT National Transportation Integrated Search

2010-08-01

Radio frequency identification device (RFID) technology provides the capability to store a unique identification : number and some basic attribute information, which can be retrieved wirelessly. This research project studied : the feasibility of usin...

Technical Evaluation Motor No. 7 (TEM-7)

NASA Technical Reports Server (NTRS)

Hughes, Phil

1991-01-01

The Technical Evaluation Motor No. 7 (TEM-7) test was a full-scale, full duration static test firing of a high performance motor-configuration solid rocket motor with nozzle vectoring. The final test report documents the procedures, performance, and results of the static test firing of TEM-7. All observations, discussions, conclusions, and recommendations included in the report are complete and final except for the TEM-7 fixed housing unbond investigation. A presentation and discussion of TEM-7 performance, anomalies, and test result concurrence with the objectives outlined in CTP-0107, Rev A, Space Shuttle Technical Evaluation Motor No. 7 (TEM-7) Static Fire Test Plan are included.

Demonstration of the feasibility of automated silicon solar cell fabrication

NASA Technical Reports Server (NTRS)

Taylor, W. E.; Schwartz, F. M.

1975-01-01

A study effort was undertaken to determine the process, steps and design requirements of an automated silicon solar cell production facility. Identification of the key process steps was made and a laboratory model was conceptually designed to demonstrate the feasibility of automating the silicon solar cell fabrication process. A detailed laboratory model was designed to demonstrate those functions most critical to the question of solar cell fabrication process automating feasibility. The study and conceptual design have established the technical feasibility of automating the solar cell manufacturing process to produce low cost solar cells with improved performance. Estimates predict an automated process throughput of 21,973 kilograms of silicon a year on a three shift 49-week basis, producing 4,747,000 hexagonal cells (38mm/side), a total of 3,373 kilowatts at an estimated manufacturing cost of $0.866 per cell or $1.22 per watt.

Technical and Economic Assessment of Span-Loaded Cargo Aircraft Concepts

NASA Technical Reports Server (NTRS)

1976-01-01

The benefits are assessed of span distributed loading concepts as applied to future commercial air cargo operations. A two phased program is used to perform this assessment. The first phase consists of selected parametric studies to define significant configuration, performance, and economic trends. The second phase consists of more detailed engineering design, analysis, and economic evaluations to define the technical and economic feasibility of a selected spanloader design. A conventional all-cargo aircraft of comparable technology and size is used as a comparator system. The technical feasibility is demonstrated of the spanloader concept with no new major technology efforts required to implement the system. However, certain high pay-off technologies such as winglets, airfoil design, and advanced structural materials and manufacturing techniques need refinement and definition prior to application. In addition, further structural design analysis could establish the techniques and criteria necessary to fully capitalize upon the high degree of structural commonality and simplicity inherent in the spanloader concept.

Final Scientific/Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, R. C.; McCarley, T. M.

2006-05-04

. Platform teams organize faculty and students for cross-disciplinary, systems-oriented research and collaborative learning. To date, nine platforms have been developed, although these will most likely be reorganized into a smaller number of broader topics. In the spring of 2004, BRT faculty initiated a regional partnership and collaborative learning program with colleagues at the University of Minnesota, Kansas State University, and South Dakota State University to develop distance education courses in biorenewable resources and technology. As a fledgling graduate program, the BRT graduate program didn’t have the breadth of resources to offer a large number of courses in biorenewables. Other schools faced a similar problem. The academic consortium as first conceived would allow students from the member schools to enroll in biorenewables courses from any of the participating schools, which would assure the necessary enrollment numbers to offer specialized course work. Since its inception, the collaborative curriculum partnership has expanded to include Louisiana State University and the University of Wisconsin. A second international curriculum development campaign was also initiated in the spring of 2004. In particular, several BRT faculty teamed with colleagues at the University of Arkansas, University of Washington, University of Gent (Belgium), National Polytechnic Institute of Toulouse (France), and Technical University of Graz (Austria) to develop an EU-US exchange program in higher education and vocational education/training (entitled “Renewable Resources and Clean Technology”).« less

Programs of Study as a State Policy Mandate: A Longitudinal Study of the South Carolina Personal Pathways to Success Initiative. Unabridged Final Technical Report (Years 1-5)

ERIC Educational Resources Information Center

Hammond, Cathy; Withington, Cairen; Sharp, Julia L.; Mobley, Catherine; Drew, Sam F.; Stringfield, Samuel C.; Stipanovic, Natalie; Swiger, Caroline M.; Daugherty, Lindsay; Griffith, Cathy

2014-01-01

This final report presents findings from data collection and analysis conducted during a five-year study by the National Dropout Prevention Center (NDPC) at Clemson University, in conjunction with colleagues from the National Research Center for Career and Technical Education (NRCCTE) at the University of Louisville. This project was one of three…

Coosa River Storage Annex, Talladega, Alabama Environmental Investigation, Final Management and Resources Utilization Plan

DTIC Science & Technology

1991-02-01

to adequately assess the health and environmental risks associated with the closure and transfer of the Annex forI other use; and 3) identification of...1990); Draft Final Technical Plan, Draft Final Sampling Design Plan and Draft Final Health and Safety Plan, USATHAMA, June 1990. 2.1.2 Draft Final...Final Technical Plan, Sampling Design Plan and Health and Safety Plan) supplied by USATHAMA. The estimate may be revised, with USATHAMA approval, as

Snohomish County Public Utility District Geothermal Energy Exploration Study Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lewis, Adam; Collar, Craig W.

2012-10-04

Supported by funds from this award, the District thoroughly explored the feasibility of a hydrothermal geothermal development within its service territory. The District successfully planned and drilled six exploratory geothermal wells and added significantly to the knowledge of the geology of the area. The Straight Creek Fault region, which was the sole location that showed significant potential for hydrothermal development in the District's service territory, was determined not to be feasible for development. The District subsequently expanded its search for geothermal development locations to include all of Washington State. Mount Baker has been identified as the area of the statemore » with the greatest potential for geothermal development. Having gathered additional information about the Mount Baker region with support from this award, the District is actively pursuing exploration and development in the area.« less

Establishment of the International Power Institute. Final technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Julius E. Coles

The International Power Institute, in collaboration with American industries, seeks to address technical, political, economic and cultural issues of developing countries in the interest of facilitating profitable transactions in power related infrastructure projects. IPI works with universities, governments and commercial organizations to render project-specific recommendations for private-sector investment considerations. IPI also established the following goals: Facilitate electric power infrastructure transactions between developing countries and the US power industry; Collaborate with developing countries to identify development strategies to achieve energy stability; and Encourage market driven solutions and work collaboratively with other international trade energy, technology and banking organizations.

Updated (BP3) Technical and Economic Feasibility Study - Electrochemical Membrane for Carbon Dioxide Capture and Power Generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghezel-Ayagh, Hossein

This topical report summarizes the results of an updated Technical & Economic Feasibility Study (T&EFS) which was conducted in Budget Period 3 of the project to evaluate the performance and cost of the Electrochemical Membrane (ECM)-based CO 2 capture system. The ECM technology is derived from commercially available inorganic membranes; the same used in FuelCell Energy’s commercial fuel cell power plants and sold under the trade name Direct FuelCell® (DFC®). The ECM stacks are utilized in the Combined Electric Power (generation) And Carbon dioxide Separation (CEPACS) systems which can be deployed as add-ons to conventional power plants (Pulverized Coal, Combinedmore » Cycle, etc.) or industrial facilities to simultaneously produce power while capturing >90% of the CO 2 from the flue gas. In this study, an ECM-based CEPACS plant was designed to capture and compress >90% of the CO 2 (for sequestration or beneficial use) from the flue gas of a reference 550 MW (nominal, net AC) Pulverized Coal (PC) Rankine Cycle (Subcritical steam) power plant. ECM performance was updated based on bench scale ECM stack test results. The system process simulations were performed to generate the CEPACS plant performance estimates. The performance assessment included estimation of the parasitic power consumption for CO 2 capture and compression, and the efficiency impact on the PC plant. While the ECM-based CEPACS system for the 550 MW PC plant captures 90% of CO 2 from the flue gas, it generates additional (net AC) power after compensating for the auxiliary power requirements of CO 2 capture and compression. An equipment list, ECM stacks packaging design, and CEPACS plant layout were developed to facilitate the economic analysis. Vendor quotes were also solicited. The economic feasibility study included estimation of CEPACS plant capital cost, cost of electricity (COE) analyses and estimation of cost per ton of CO 2 captured. The incremental COE for the ECM-based CO 2 capture is

Updated (BP3) Technical and Economic Feasibility Study - Electrochemical Membrane for Carbon Dioxide Capture and Power Generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghezel-Ayagh, Hossein

This topical report summarizes the results of an updated Technical & Economic Feasibility Study (T&EFS) which was conducted in Budget Period 3 of the project to evaluate the performance and cost of the Electrochemical Membrane (ECM)-based CO2 capture system. The ECM technology is derived from commercially available inorganic membranes; the same used in FuelCell Energy’s commercial fuel cell power plants and sold under the trade name Direct FuelCell® (DFC®). The ECM stacks are utilized in the Combined Electric Power (generation) And Carbon dioxide Separation (CEPACS) systems which can be deployed as add-ons to conventional power plants (Pulverized Coal, Combined Cycle,more » etc.) or industrial facilities to simultaneously produce power while capturing >90% of the CO2 from the flue gas. In this study, an ECM-based CEPACS plant was designed to capture and compress >90% of the CO2 (for sequestration or beneficial use) from the flue gas of a reference 550 MW (nominal, net AC) Pulverized Coal (PC) Rankine Cycle (Subcritical steam) power plant. ECM performance was updated based on bench scale ECM stack test results. The system process simulations were performed to generate the CEPACS plant performance estimates. The performance assessment included estimation of the parasitic power consumption for CO2 capture and compression, and the efficiency impact on the PC plant. While the ECM-based CEPACS system for the 550 MW PC plant captures 90% of CO2 from the flue gas, it generates additional (net AC) power after compensating for the auxiliary power requirements of CO2 capture and compression. An equipment list, ECM stacks packaging design, and CEPACS plant layout were developed to facilitate the economic analysis. Vendor quotes were also solicited. The economic feasibility study included estimation of CEPACS plant capital cost, cost of electricity (COE) analyses and estimation of cost per ton of CO2 captured. The incremental COE for the ECM-based CO2 capture is expected

Feasibility of mHealth and Near Field Communication technology based medication adherence monitoring.

PubMed

Morak, Juergen; Schwarz, Mark; Hayn, Dieter; Schreier, Guenter

2012-01-01

Poor patients' adherence to intake of prescribed medication has been identified as a serious problem in the treatment of chronically ill patients. Technical solutions are needed to measure and - if necessary - to increase the patients' adherence. A telemonitoring solution was developed to record a patient's medication intake based on smart blisters and mobile phones with NFC functionality. The components allowed recording of drug type, timestamp, and dosage of pills taken. The system's usability and technical feasibility was evaluated in the course of an application study. Over a period of 13 months 59 patients suffering from diabetes were monitored. 1,760 blisters were handed out to these patients and 14,843 takeout events were recorded and transmitted via mobile phone. Results indicate the feasibility of this concept to monitor adherence. Although the system still needs to be optimized for routine use it shows the potential for targeting the problem of poor patient adherence by NFC enabled devices.

Technical feasibility of an ROV with on-board power

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sayer, P.; Bo, L.

1994-12-31

An ROI`s electric power, control and communication signals are supplied from a surface ship or platform through an umbilical cable. Though cable design has evolved steadily, there are still severe limitations such as heavy weight and cost. It is well known that the drag imposed by the cable limits the operational range of the ROV in deep water. On the other hand, a cable-free AUV presents problems in control, communication and transmission of data. Therefore, an ROV with on-board and small-diameter cable could offer both a large operating range (footprint) and real-time control. This paper considers the feasibility of suchmore » an ROV with on-board power, namely a Self-Powered ROV (SPROV). The selection of possible power sources is first discussed before comparing the operational performance of an SPROV against a conventional ROV. It is demonstrated how an SPROV with a 5mm diameter tether offers a promising way forward, with on-board power of up to 40 kW over 24 hours. In water depths greater than 50m the reduced drag of the SPROV tether is very advantageous.« less

Emissions Inventory Final Rule TSD

EPA Pesticide Factsheets

This technical support document (TSD) provides the details of emissions data processing done in support of EPA's final rulemaking effort for the Federal Transport Rule, now known as the Cross-State Air Pollution Rule.

Joint Common Architecture Demonstration (JCA Demo) Final Report

DTIC Science & Technology

2016-07-28

approach for implementing open systems [16], formerly known as the Modular Open Systems Approach (MOSA). OSA is a business and technical strategy to... TECHNICAL REPORT RDMR-AD-16-01 JOINT COMMON ARCHITECTURE DEMONSTRATION (JCA DEMO) FINAL REPORT Scott A. Wigginton... Modular Avionics .......................................................................... 5 E. Model-Based Engineering

Final Technical Report for Year 5 Early Career Research Project "Viscosity and equation of state of hot and dense QCD matter"

DOE Office of Scientific and Technical Information (OSTI.GOV)

Molnar, Denes

2016-05-25

The Section below summarizes research activities and achievements during the fifth (last) year of the PI’s Early Career Research Project (ECRP). Unlike the first four years of the project, the last year was not funded under the American Recovery and Reinvestment Act (ARRA). The ECRP advanced two main areas: i) radiative 3 ↔ 2 radiative transport, via development of a new computer code MPC/Grid that solves the Boltzmann transport equation in full 6+1D (3X+3V+time); and ii) application of relativistic hydrodynamics, via development of a self-consistent framework to convert viscous fluids to particles. In Year 5 we finalized thermalization studies withmore » radiative gg ↔ ggg transport (Sec. 1.1.1) and used nonlinear covariant transport to assess the accuracy of fluid-to-particle conversion models (Sec. 1.1.2), calculated observables with self-consistent fluid-to-particle conversion from realistic viscous hydrodynamic evolution (Secs. 1.2.1 and 1.2.2), extended the covariant energy loss formulation to heavy quarks (Sec. 1.4.1) and studied energy loss in small systems (Sec. 1.4.2), and also investigated how much of the elliptic flow could have non-hydrodynamic origin (Sec 1.3). Years 1-4 of the ECRP were ARRA-funded and, therefore, they have their own report document ’Final Technical Report for Years 1-4 of the Early Career Research Project “Viscosity and equation of state of hot and dense QCD matter”’ (same award number DE-SC0004035). The PI’s group was also part of the DOE JET Topical Collaboration, a multi-institution project that overlapped in time significantly with the ECRP. Purdue achievements as part of the JET Top- ical Collaboration are in a separate report “Final Technical Report summarizing Purdue research activities as part of the DOE JET Topical Collaboration” (award DE-SC0004077).« less

Research in Automatic Russian-English Scientific and Technical Lexicography. Final Report.

ERIC Educational Resources Information Center

Wayne State Univ., Detroit, MI.

Techniques of reversing English-Russian scientific and technical dictionaries into Russian-English versions through semi-automated compilation are described. Sections on manual and automatic processing discuss pre- and post-editing, the task program, updater (correction of errors and revision by specialist in a given field), the system employed…

Feasibility Study on Fully Automatic High Quality Translation: Volume I. Final Technical Report.

ERIC Educational Resources Information Center

Lehmann, Winifred P.; Stachowitz, Rolf

The object of this theoretical inquiry is to examine the controversial issue of a fully automatic high quality translation (FAHQT) in the light of past and projected advances in linguistic theory and hardware/software capability. This first volume of a two-volume report discusses the requirements of translation and aspects of human and machine…

Feasibility Study on Fully Automatic High Quality Translation: Volume II. Final Technical Report.

ERIC Educational Resources Information Center

Lehmann, Winifred P.; Stachowitz, Rolf

This second volume of a two-volume report on a fully automatic high quality translation (FAHQT) contains relevant papers contributed by specialists on the topic of machine translation. The papers presented here cover such topics as syntactical analysis in transformational grammar and in machine translation, lexical features in translation and…

The feasibility of solar energy usage on Red River Army Depot. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crowder, G.W.

This feasibility study considers the usage of solar energy to heat and cool the main office buildings on the Red River Army Depot, Texarkana Texas. Solar energy costs are compared with the present heating and cooling system costs with an economic analysis using the annual worth and present worth methods. (GRA)

Installation Restoration Program Stage 3. Remedial Investigation/ Feasibility Study Elmendorf AFB, Alaska. Volume 2. Section 5 - Bibliography Text

DTIC Science & Technology

1990-05-01

ELME’IDORF AFB, AK UNITED STATES AIR FORCE OCCUPATIONAL & ENVIRONMENTAL HEALTH LABORATORY (AFSC) ilb(. IiCAL Sr.(VICES DIVISION (AFOEHLi £3) I BROOKS AIR...UNITED STATES AIR FORCE OCCUPATIONAL AND ENVIRONMENTAL HEALTH LABORATORY (AFSC) TECHNICAL SERVICES DIVISION (AFOEHL/TS) BROOKS AIR FORCE BASE, TEXAS...the following criteria: technical feasibility, institutional requirements, environmental impacts, public health impacts, and cost. This Alternative

TADS Final Evaluation Report, 1980-81. Appendix S.

ERIC Educational Resources Information Center

Suarez, Tanya M.; And Others

The document contains the final report of the Technical Assistance Development System (TADS), a program which provided technical assistance (TA) services to 53 Handicapped Children's Early Education Program (HCEEP) demonstration projects and 13 State Implementation Grants (SIGs). The evaluation report is divided into five sections. Section 1…

78 FR 41331 - Defense Federal Acquisition Regulation Supplement; Technical Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-10

... DEPARTMENT OF DEFENSE Defense Acquisition Regulations System 48 CFR Part 225 Defense Federal Acquisition Regulation Supplement; Technical Amendments AGENCY: Defense Acquisition Regulations System, Department of Defense (DoD). ACTION: Final rule. SUMMARY: DoD is making technical amendment to the Defense...

Economic feasibility of producing inside-out beams from small-diameter logs

Treesearch

David W. Patterson; Richard A. Kluender; James E. Granskog

2002-01-01

Previous work has shown that it is technically feasible to produce inside-out (ISO) beams by taking small-diameter (5 to 7 in.) logs, slabbing four sides, quartering the cant, and turning the quarters inside out and gluing them together. After drying, the beams were found to be straight, with no cracks, and of equal or better mechanical properties than solid sawn...

A Patient Learning Center for an Army MEDDAC - A Feasibility Study. Final Report.

ERIC Educational Resources Information Center

Kucha, Deloros H.

A feasibility study was conducted to examine in detail, analyze, and describe the development and operation (system effectiveness and efficiency) of a patient learning center in a MEDDAC, and to provide such information to the Surgeon General for use in planning future health care delivery to military-care eligible beneficiaries. Study objectives…

77 FR 37284 - Technical Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-21

... DEPARTMENT OF LABOR Office of Workers' Compensation Programs 20 CFR Parts 701, 702, 703, 725, and 726 RIN 1240-AA05 Technical Amendments AGENCY: Office of Workers' Compensation Programs, Labor. ACTION: Final rule. SUMMARY: The Office of Workers' Compensation Programs is making [[Page 37285

77 FR 47495 - Final Priority; Technical Assistance on State Data Collection, Analysis, and Reporting-National...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-08

... intervention and preschool service providers with data on their qualifications, certification, and preparation... Priority; Technical Assistance on State Data Collection, Analysis, and Reporting--National IDEA Technical Assistance Center on Early Childhood Longitudinal Data Systems; Rule #0;#0;Federal Register / Vol. 77, No...

Hydrogen energy systems studies. Final technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ogden, J.M.; Kreutz, T.; Kartha, S.

1996-08-13

The results of previous studies suggest that the use of hydrogen from natural gas might be an important first step toward a hydrogen economy based on renewables. Because of infrastructure considerations (the difficulty and cost of storing, transmitting and distributing hydrogen), hydrogen produced from natural gas at the end-user`s site could be a key feature in the early development of hydrogen energy systems. In the first chapter of this report, the authors assess the technical and economic prospects for small scale technologies for producing hydrogen from natural gas (steam reformers, autothermal reformers and partial oxidation systems), addressing the following questions:more » (1) What are the performance, cost and emissions of small scale steam reformer technology now on the market? How does this compare to partial oxidation and autothermal systems? (2) How do the performance and cost of reformer technologies depend on scale? What critical technologies limit cost and performance of small scale hydrogen production systems? What are the prospects for potential cost reductions and performance improvements as these technologies advance? (3) How would reductions in the reformer capital cost impact the delivered cost of hydrogen transportation fuel? In the second chapter of this report the authors estimate the potential demand for hydrogen transportation fuel in Southern California.« less

Final Rule for Technical Amendments to the Highway and Nonroad Diesel Regulations

EPA Pesticide Factsheets

This action corrects errors and omissions from the previous rules, makes minor changes to the regulations to assist entities with regulatory compliance, and makes technical amendments that resulted from discussions with various diesel stakeholders.

A joint university-government technical editing program

NASA Technical Reports Server (NTRS)

Stohrer, Freda F.; Pinelli, Thomas E.

1978-01-01

The NASA Langley Research Center (LaRC) and Old Dominion University have designed a mutually useful technical editing program. A university team made up of an English instructor and two graduate students - one from English, one from engineering - works with a senior editor from LaRC to prepare technical reports for publication. A round-robin technique gives the university team editorial commentary from both language and technical specialists; the senior editor from LaRC supervises reports through final publication. To date, the system has provided LaRC with a respectable product and university students with valuable on-the-job training.

Technical Assistance and Training from the Document Design Project. Final Report.

ERIC Educational Resources Information Center

American Institutes for Research, Washington, DC.

Contained in this report is a description of the technical assistance and training phase of the Document Design Project, a program funded by the National Institute of Education and intended to address and correct the readability problems posed by public documents. The first section of the report provides background material on the assistance and…

Agua Caliente Solar Feasibility and Pre-Development Study Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carolyn T. Stewart, Managing Partner; Red Mountain Energy Partners

2011-04-26

Evaluation of facility- and commercial-scale solar energy projects on the Agua Caliente Band of Cahuilla Indians Reservation in Palm Springs, CA. The Agua Caliente Band of Cahuilla Indians (ACBCI) conducted a feasibility and pre-development study of potential solar projects on its lands in southern California. As described below, this study as a logical and necessary next step for ACBCI. Support for solar project development in California, provided through the statewide California Solar Initiative (CSI), its Renewable Portfolio Standard and Feed-in Tariff Program, and recently announced Reverse Auction Mechanism, provide unprecedented support and incentives that can be utilized by customers ofmore » California's investor-owned utilities. Department of Energy (DOE) Tribal Energy Program funding allowed ACBCI to complete its next logical step to implement its Strategic Energy Plan, consistent with its energy and sustainability goals.« less

Final Technical Report for Award DESC0011912, "Trimodal Tapping Mode Atomic Force Microscopy: Simultaneous 4D Mapping of Conservative and Dissipative Probe-Sample Interactions of Energy-Relevant Materials”

DOE Office of Scientific and Technical Information (OSTI.GOV)

Solares, Santiago D.

The final project report covering the period 7/1/14-6/30/17 provides an overview of the technical accomplishments in the areas of (i) fundamental viscoelasticity, (ii) multifrequency atomic force microscopy, and (iii) characterization of energy-relevant materials with atomic force microscopy. A list of publications supported by the project is also provided.

The role of non-technical skills in surgery

PubMed Central

Agha, Riaz A.; Fowler, Alexander J.; Sevdalis, Nick

2015-01-01

Non-technical skills are of increasing importance in surgery and surgical training. A traditional focus on technical skills acquisition and competence is no longer enough for the delivery of a modern, safe surgical practice. This review discusses the importance of non-technical skills and the values that underpin successful modern surgical practice. This narrative review used a number of sources including written and online, there was no specific search strategy of defined databases. Modern surgical practice requires; technical and non-technical skills, evidence-based practice, an emphasis on lifelong learning, monitoring of outcomes and a supportive institutional and health service framework. Finally these requirements need to be combined with a number of personal and professional values including integrity, professionalism and compassionate, patient-centred care. PMID:26904193

[The study of establishment of the " Chinese provincial Blindness prevention technical guidance group performance evaluation system"].

PubMed

Lu, L N; He, X G; Zhu, J F; Xu, X; Zhang, R; Hu, X; Zou, H D

2016-11-11

Objective: To establish an assessment system, including indexes and scoring methods, that can be used for performance evaluation of the provincial blindness prevention technical guidance group properly and effectively . Methods: The indexes and scoring methods were set based on the core content of The " National Plan of Prevention and Treatment of Blindness (2012-2015)" , the specific requirement and target of the World Health Organization (WHO) "For the General Eye Health: Global plan of Action (2014-2019)" , and the current situation of the China's provinces and autonomous regions. These indexes should be of effectiveness, feasibility, comparability, guidance and advancing. Formed by a literature review of candidate indicators, the framework of the system is built by qualitative assessment. With the Delphi method, the system was further revised and improved. Empirical pilot study was then used to prove the feasibility, followed by the final qualitative analysis that establish the " Chinese provincial Blindness prevention technical guidance group performance evaluation system" . Results: Through the literature review and qualitative assessment, a six dimensional system framework was built, including 6 first-level indicators, 16 second-level indicators, and 29 third-level indicators through Delphi method evaluation. With the variation coefficient method, the coeffiences of the first-level index weight were calculated as: Organization and management 0.15, Development and implementation of blindness prevention plans 0.15, Implementation of blindness prevention projects 0.14, Training 0.17, Health education 0.18, and Cooperation and exchanges 0.21. The specific scoring method for this system is confirmed as: data and files check, field interview, and record interview, sampling investigation. Empirical pilot study was conducted in the Jilin, Guizhou and Gansu provinces, and the self-assessment results from local experts were consistent with the scores from the systems

Cargo transportation by airships: a systems study. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, C.J.; Dalton, C.

1976-05-01

A systems engineering study of a lighter than air airship transportation system was conducted. The feasibility of the use of airships in hauling cargo was demonstrated. Social, legal, environmental and political factors were considered as well as the technical factors necessary to design an effective airship transportation system. In order to accomplish an effective airship transportation program two phases of implementation were recommended. Phase I would involve a fleet of rigid airships of 3.5 million cubic feet displacement capable of carrying 25 tons of cargo internal to the helium-filled gas bag. The Phase I fleet would demonstrate the economic andmore » technical feasibility of modern-day airships while providing a training capability for the construction and operation of larger airships. The Phase II portion would be a fleet of rigid airships of 12 million cubic feet displacement capable of carrying a cargo of 100 tons a distance of 2,000 miles at a cruising speed of 60 mph. An economic analysis is given for a variety of missions for both Phase I and Phase II airships.« less

Scalable data management, analysis and visualization (SDAV) Institute. Final Scientific/Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Geveci, Berk

The purpose of the SDAV institute is to provide tools and expertise in scientific data management, analysis, and visualization to DOE’s application scientists. Our goal is to actively work with application teams to assist them in achieving breakthrough science, and to provide technical solutions in the data management, analysis, and visualization regimes that are broadly used by the computational science community. Over the last 5 years members of our institute worked directly with application scientists and DOE leadership-class facilities to assist them by applying the best tools and technologies at our disposal. We also enhanced our tools based on inputmore » from scientists on their needs. Many of the applications we have been working with are based on connections with scientists established in previous years. However, we contacted additional scientists though our outreach activities, as well as engaging application teams running on leading DOE computing systems. Our approach is to employ an evolutionary development and deployment process: first considering the application of existing tools, followed by the customization necessary for each particular application, and then the deployment in real frameworks and infrastructures. The institute is organized into three areas, each with area leaders, who keep track of progress, engagement of application scientists, and results. The areas are: (1) Data Management, (2) Data Analysis, and (3) Visualization. Kitware has been involved in the Visualization area. This report covers Kitware’s contributions over the last 5 years (February 2012 – February 2017). For details on the work performed by the SDAV institute as a whole, please see the SDAV final report.« less

FBI fingerprint identification automation study. AIDS 3 evaluation report. Volume 4: Economic feasibility

NASA Technical Reports Server (NTRS)

Mulhall, B. D. L.

1980-01-01

The results of the economic analysis of the AIDS 3 system design are presented. AIDS 3 evaluated a set of economic feasibility measures including life cycle cost, implementation cost, annual operating expenditures and annual capital expenditures. The economic feasibility of AIDS 3 was determined by comparing the evaluated measures with the same measures, where applicable, evaluated for the current system. A set of future work load scenarios was constructed using JPL's environmental evaluation study of the fingerprint identification system. AIDS 3 and the current system were evaluated for each of the economic feasibility measures for each of the work load scenarios. They were compared for a set of performance measures, including response time and accuracy, and for a set of cost/benefit ratios, including cost per transaction and cost per technical search. Benefit measures related to the economic feasibility of the system are also presented, including the required number of employees and the required employee skill mix.

Percutaneous radiofrequency ablation of hepatic tumours: factors affecting technical failure of artificial ascites formation using an angiosheath.

PubMed

Kang, T W; Lee, M W; Hye, M J; Song, K D; Lim, S; Rhim, H; Lim, H K; Cha, D I

2014-12-01

To evaluate the technical feasibility of artificial ascites formation using an angiosheath before percutaneous radiofrequency ablation (RFA) for hepatic tumours and to determine predictive factors affecting the technical failure of artificial ascites formation. This retrospective study was approved by the institutional review board. One hundred and thirteen patients underwent percutaneous RFA of hepatic tumours after trying to make artificial ascites using an angiosheath to avoid collateral thermal damage. The technical success rate of making artificial ascites using an angiosheath and conversion rate to other techniques after initial failure of making artificial ascites were evaluated. The technical success rate for RFA was assessed. In addition, potential factors associated with technical failure including previous history of transcatheter arterial chemoembolization (TACE) or RFA, type of abdominal surgery, and adjacent perihepatic structures were reviewed. Predictive factors for the technical failure of artificial ascites formation were analysed using multivariate analysis. The technical success rates of artificial ascites formation by angiosheath and that of RFA were 84.1% (95/113) and 97.3% (110/113), respectively. The conversion rate to other techniques after the failure of artificial ascites formation using an angiosheath was 15.9% (18/113). Previous hepatic resection was the sole independent predictive factor affecting the technical failure of artificial ascites formation (p<0.001, odds ratio = 29.03, 95% confidence interval: 4.56-184.69). Making artificial ascites for RFA of hepatic tumours using an angiosheath was technically feasible in most cases. However, history of hepatic resection was a significant predictive factor affecting the technical failure of artificial ascites formation. Copyright © 2014 The Royal College of Radiologists. Published by Elsevier Ltd. All rights reserved.

The Feasibility and Advisability of Providing a Centralized Bibliographic Service for TAFE in Queensland.

ERIC Educational Resources Information Center

Ridden, Elva A.

This study examines the feasibility of establishing a centralized bibliographic service for the Resource Materials Centres (RCM) of the Colleges of Technical and Further Education (TAFE) in Queensland, Australia. It examines the context in which services can operate, and possible functions. The organizational aspects of TAFE in planning,…

Feasibility and roadmap analysis for malaria elimination in China.

PubMed

Zhou, Xiao-Nong; Xia, Zhi-Gui; Wang, Ru-Bo; Qian, Ying-Jun; Zhou, Shui-Sen; Utzinger, Jürg; Tanner, Marcel; Kramer, Randall; Yang, Wei-Zhong

2014-01-01

To understand the current status of the malaria control programme at the county level in accordance with the criteria of the World Health Organisation, the gaps and feasibility of malaria elimination at the county and national levels were analysed based on three kinds of indicators: transmission capacity, capacity of the professional team, and the intensity of intervention. Finally, a roadmap for national malaria elimination in the People's Republic of China is proposed based on the results of a feasibility assessment at the national level. Copyright © 2014 Elsevier Ltd. All rights reserved.

Compendium of Executive Summaries from the Maglev System Concept Definition. Final Reports.

DTIC Science & Technology

1993-03-01

This report contains the Executive Summaries from the four System Concept Definition (SCD) studies awarded under the National Maglev Initiative...These summaries present the technical feasibility, performance, capital, operating and maintenance costs for a maglev system that would be available by

Final Scientific Technical Report Crowder College MARET Center

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boyt, Art; Eberle, Dan; Hudson, Pam

validating new applications of solar and other renewable technologies, the MARET Facility will house a wide variety of programs which will advance implementation of renewable energy throughout the region. These program goals include; Curriculum in renewable energy for pre-engineering transfer programs; Certification and degree programs for technical degrees for Energy Efficiency, Wind, Photovoltaic and Solar Thermal professionals; Short courses and workshops for building management and design professionals; Public education and demonstration projects in renewable energy through conferences and K-12 educational outreach; Technical degree offering in building construction incorporating “best practices” for energy efficiency and renewables; and Business incubators for new renewable energy businesses and new product development The new MARET facility will support the mission of the US Department of Energy (DOE) Solar Program, “to improve America’s security, environmental quality, and economic prosperity through public-private partnerships that bring reliable and affordable solar energy technologies to the marketplace,” through a variety of educational and business assistance programs. Further, technical innovations planned for the MARET facility and its applied research activities will advance the Solar Program strategic goals to “reduce the cost of solar energy to the point it becomes competitive in relevant energy markets (e.g., buildings, power plants) and for solar technology to enable a sustainable solar industry.” Overarching Goals relative to program needs, future expansion, flexibility, quality of materials, and construction and operational costs:; Experimental: The structure and systems of the building operate as an educational resource. The systems are meant to be a source for data collection and study for building users and instructors; Educational: Part of the evolution of this building and its ongoing goals is to use the building as an educational tool

Freight Wing Trailer Aerodynamics Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sean Graham

2007-10-31

products intended to further improve efficiency, lower costs, and enhance durability. Resulting products demonstrated a 30% efficiency improvement in full scale wind tunnel tests. The fuel savings of our most promising product, the “Belly Fairing” increased from 4% to 6% in scientific track and operational tests. The project successfully demonstrated the economic feasibility of trailer aerodynamics and positioned the technology to realize significant public benefits. Scientific testing conducted with partners such as the EPA Smartway program and Transport Canada clearly validated the fuel and emission saving potential of the technology. The Smartway program now recommends trailer aerodynamics as a certified fuel saving technology and is offering incentives such as low interest loans. Trailer aerodynamics can save average trucks over 1,100 gallons of fuel an 13 tons of emissions every 100,000 miles, a distance many trucks travel annually. These fuel savings produce a product return on investment period of one to two years in average fleet operations. The economic feasibility of the products was validated by participating fleets, several of which have since completed large implementations or demonstrated an interest in volume orders. The commercialization potential of the technology was also demonstrated, resulting in a national distribution and manufacturing partnership with a major industry supplier, Carrier Transicold. Consequently, Freight Wing is well positioned to continue marketing trailer aerodynamics to the trucking industry. The participation of leading fleets in this project served to break down the market skepticism that represents a primary barrier to widespread industry utilization. The benefits of widespread utilization of the technology could be quite significant for both the transportation industry and the public. Trailer aerodynamics could potentially save the U.S. trucking fleet over a billion gallons of fuel and 20 million tons of emissions annually.« less

Astrobee Periodic Technical Review (PTR) Delta 3

NASA Technical Reports Server (NTRS)

Provencher, Christopher; Smith, Marion F.; Smith, Ernest Everett; Bualat, Maria Gabriele; Barlow, Jonathan Spencer

2017-01-01

Astrobee is a free flying robot for the inside of the International Space Station (ISS). The Periodic Technical Review (PTR) delta 3 is the final design review of the system presented to stakeholders.

2005 v4.2 Technical Support Document

EPA Pesticide Factsheets

Technical Support Document for the Final Transport Rule describes how updated 2005 NEI, version 2 emissions and were processed for air quality modeling in support of the Cross-state Air Pollution Rule (CSAPR).

Final Technical Report for subcontract number B612144

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mayali, X.; Marcu, O.

The original statement of work stipulated that the Subcontractor shall perform bacterial and algal cultivation and manipulation, microbe isolation, preparation of samples for sequencing and isotopic analysis, data analysis, and manuscript preparation. The Subcontractor shall work closely with Dr. Mayali and other LLNL scientists, and shall participate in monthly SFA meetings (either in person or by telephone). The Subcontractor shall deliver a final report at the conclusion of the work.

Advanced technology gas-fired commercial clothes dryer. Final report, April 1985-December 1988

DOE Office of Scientific and Technical Information (OSTI.GOV)

Topping, R.F.

1991-04-01

The objective of this effort was to demonstrate the technical feasibility of an advanced technology commercial clothes dryer (ATD) which could provide improved fuel efficiency and reduced drying time without burning or otherwise damaging the clothes load.

Final Technical Report for Years 1-4 of the Early Career Research Project "Viscosity and equation of state of hot and dense QCD matter" - ARRA portion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Molnar, Denes

2014-04-14

The Section below summarizes research activities and achievements during the first four years of the PI’s Early Career Research Project (ECRP). Two main areas have been advanced: i) radiative 3 ↔ 2 radiative transport, via development of a new computer code MPC/Grid that solves the Boltzmann transport equation in full 6+1D (3X+3V+time) on both single-CPU and parallel computers; ii) development of a self-consistent framework to convert viscous fluids to particles, and application of this framework to relativistic heavy-ion collisions, in particular, determination of the shear viscosity. Year 5 of the ECRP is under a separate award number, and therefore itmore » has its own report document ’Final Technical Report for Year 5 of the Early Career Research Project “Viscosity and equation of state of hot and dense QCDmatter”’ (award DE-SC0008028). The PI’s group was also part of the DOE JET Topical Collaboration, a multi-institution project that overlapped in time significantly with the ECRP. Purdue achievements as part of the JET Topical Collaboration are in a separate report “Final Technical Report summarizing Purdue research activities as part of the DOE JET Topical Collaboration” (award DE-SC0004077).« less

The Imperial Paediatric Emergency Training Toolkit (IPETT) for use in paediatric emergency training: development and evaluation of feasibility and validity.

PubMed

Lambden, Simon; DeMunter, Claudine; Dowson, Anne; Cooper, Mehrengise; Gautama, Sanjay; Sevdalis, Nick

2013-06-01

To develop and test the feasibility, reliability, and validity of a practical toolkit for the assessment and feedback of skills required to manage paediatric emergencies in critical care settings. The Imperial Paediatric Emergency Training Toolkit (IPETT) was developed based on current evidence-base and expert input. IPETT assesses both technical and non-technical skills. The technical component covers skills in the areas of clinical assessment, airway and breathing, cardiovascular, and drugs. The non-technical component is based on the validated NOTECHS tool and covers communication and interaction, cooperation and team skills, leadership and managerial skills, and decision-making. The reliability (internal consistency), content validity (inter-correlations between different skills) and concurrent validity (correlations between global technical and non-technical scores) of IPETT were prospectively evaluated in 45 simulated paediatric crises carried out in a PICU with anaesthetic and paediatric trainees (N=52). Non-parametric analyses were carried out. Significance was set at P<0.05. Cronbach alpha reliability coefficients were overall acceptable for the technical (alpha range=0.638-0.810) and good for the non-technical (alpha range=0.701-0.899) component of IPETT. The median inter-skill correlation was rho=0.564 and rho=0.549 for the technical and non-technical components, respectively. These indicate good content validity, as the skills were inter-related but not redundant. We also demonstrate a correlation between the global technical and non-technical scores (rho=0.471) - all Ps<0.05 during the assessments. IPETT offers a psychometrically viable and feasible to use tool in the context of paediatric emergencies training. This study shows that assessment of technical and non-technical skills in combination may offer a more clinically relevant model for training in paediatric emergencies. Further validation should aim to demonstrate skill retention over time and

Renewable Fuel Standard (RFS2): Final Rule Additional Resources

EPA Pesticide Factsheets

The final rule of fuels and fuel additives: renewable fuel standard program is published on March 26, 2010 and is effective on July 1, 2010. You will find the links to this final rule and technical amendments supporting this rule.

Promotion of the Equal Access of Girls and Women to Technical and Vocational Education. Studies on Technical and Vocational Education 7.

ERIC Educational Resources Information Center

United Nations Educational, Scientific, and Cultural Organization, Paris (France).

This monograph includes the final report of the International Expert Meeting on the Promotion of Equal Access of Girls and Women to Technical and Vocational Education (TVE) held in Seoul, Republic of Korea, and country discussion papers. The final report is composed of an introduction that proposes that many Member States require special measures…

Seminar for Preparation of Professional Personnel for Vocational-Technical Education. Final Report.

ERIC Educational Resources Information Center

Dillon, Roy D.; Horner, James T.

Seminar participants included college administrative officers, state vocational education directors, vocational-technical teacher educators, and Office of Education staff. The purpose of the June, 1968 seminar was to consider strategies for resolving critical vocational education personnel supply and demand problems. Presentations included in the…

Technical assessment of maglev system concepts. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lever, J.H.

1998-10-01

The Government Maglev System Assessment Team operated from 1991 to 1993 as part of the National Maglev Initiative. They assessed the technical viability of four US Maglev system concepts, using the French TGV high speed train and the German TR07 Maglev system as assessment baselines. Maglev in general offers advantages that include high speed potential, excellent system control, high capacity, low energy consumption, low maintenance, modest land requirements, low operating costs, and ability to meet a variety of transportation missions. Further, the US Maglev concepts could provide superior performance to TR07 for similar cost or similar performance for less cost.more » They also could achieve both lower trip times and lower energy consumption along typical US routes. These advantages result generally from the use of large gap magnetic suspensions, more powerful linear synchronous motors and tilting vehicles. Innovative concepts for motors, guideways, suspension, and superconducting magnets all contribute to a potential for superior long term performance of US Maglev systems compared with TGV and TR07.« less

Wind Resource and Feasibility Assessment Report for the Lummi Reservation

DOE Office of Scientific and Technical Information (OSTI.GOV)

DNV Renewables; J.C. Brennan & Associates, Inc.; Hamer Environmental L.P.

2012-08-31

This report summarizes the wind resource on the Lummi Indian Reservation (Washington State) and presents the methodology, assumptions, and final results of the wind energy development feasibility assessment, which included an assessment of biological impacts and noise impacts.

Final Scientific/Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reeder, Richard; Phillips, Brian

A variety of calcifying organisms produce a transient or metastable amorphous calcium carbonate (ACC) precursor phase that is assembled and subsequently transformed into a crystalline biomineral, typically calcite or aragonite. The complex shapes, hierarchical structures, and unique physical properties of the biominerals that result from this calcification pathway have stimulated interest in adapting these concepts for the design and creation of bio-inspired functional materials in the laboratory. ACC also forms as a reactive precursor in diverse inorganic systems and is likely to play a much broader role in calcium carbonate formation. Knowledge of the structure, composition, and behavior of thismore » metastable phase is critical for establishing a structural and mechanistic framework for calcium carbonate formation and its role in biogeochemical processes, including carbon cycling. Minor additives, such as magnesium, phosphorus, and organic macromolecules, are known to play important roles in controlling ACC stability, transformation kinetics, and selection of final crystalline polymorph. Molecular water also occurs in many types of ACC and is thought to play a structural role in its stability and transformation behavior. One of the major challenges that remain unresolved is identification of the structural basis for the role of these minor additives and molecular water. The absence of long-range order in ACC, and other amorphous phases, has posed a challenge for study by techniques commonly used for crystalline solids. Preliminary studies in our group show that the combination of two techniques, synchrotron X-ray-based pair distribution function (PDF) analysis and nuclear magnetic resonance (NMR) spectroscopy can provide entirely new insight to structural properties of synthetic ACC over length scales that are most relevant for understanding its transformation properties. Building on preliminary experiments, we propose a systematic study of synthesis

Control technology appendices for pollution control technical manuals. Final report, June 1982-February 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1983-04-01

The document is one of six technical handbooks prepared by EPA to help government officials granting permits to build synfuels facilities, synfuels process developers, and other interested parties. They provide technical data on waste streams from synfuels facilities and technologies capable of controlling them. Process technologies covered in the manuals include coal gasification, coal liquefaction by direct and idirect processing, and the extraction of oil from shale. The manuals offer no regulatory guidance, allowing the industry flexibility in deciding how best to comply with environmental regulations.

Assurance Penalty Level Analysis Final Rule TSD

EPA Pesticide Factsheets

This Technical Support Document (TSD) supports EPA’s determination that the final Transport Rule’s assurance provision penalty requirement provides sufficient deterrence against a state exceeding its assurance level.

The Effectiveness and Feasibility of a TRISNET Regional Center in Information Transfer. Final Report.

ERIC Educational Resources Information Center

Rath, Gustave J.; And Others

A study was conducted to assess the feasibility of establishing a regional information transfer center within the context of the National Network of Transportation Research Information Services (TRISNET). The principle areas of investigation were: (1) the transportation information needs of the public and private sectors; (2) the utility of…

Final Technical Report - SciDAC Cooperative Agreement: Center for Wave Interactions with Magnetohydrodynamics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schnack, Dalton D.

Final technical report for research performed by Dr. Thomas G. Jenkins in collaboration with Professor Dalton D. Schnack on SciDAC Cooperative Agreement: Center for Wave Interactions with Magnetohydrodyanics, DE-FC02-06ER54899, for the period of 8/15/06 - 8/14/11. This report centers on the Slow MHD physics campaign work performed by Dr. Jenkins while at UW-Madison and then at Tech-X Corporation. To make progress on the problem of RF induced currents affect magnetic island evolution in toroidal plasmas, a set of research approaches are outlined. Three approaches can be addressed in parallel. These are: (1) Analytically prescribed additional term in Ohm's law tomore » model the effect of localized ECCD current drive; (2) Introduce an additional evolution equation for the Ohm's law source term. Establish a RF source 'box' where information from the RF code couples to the fluid evolution; and (3) Carry out a more rigorous analytic calculation treating the additional RF terms in a closure problem. These approaches rely on the necessity of reinvigorating the computation modeling efforts of resistive and neoclassical tearing modes with present day versions of the numerical tools. For the RF community, the relevant action item is - RF ray tracing codes need to be modified so that general three-dimensional spatial information can be obtained. Further, interface efforts between the two codes require work as well as an assessment as to the numerical stability properties of the procedures to be used.« less

Direct Final Rule for Technical Amendments for Marine Spark-Ignition Engines and Vessels

EPA Pesticide Factsheets

Rule published September 16, 2010 to make technical amendments to the design standard for portable marine fuel tanks. This rule incorporates safe recommended practices, developed through industry consensus.

Final Technical Report: "Achieving Regional Energy Efficiency Potential in the Southeast”

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mahoney, Mandy

The overall objective of this award was to facilitate sharing of DOE resources and best practices as well as provide technical assistance to key stakeholders to support greater compliance with energy efficiency standards and increased energy savings. The outcomes of this award include greater awareness among key stakeholders on energy efficiency topics, increased deployment and utilization of DOE resources, and effective policies and programs to support energy efficiency in the Southeast.

An analysis of the technical status of high level radioactive waste and spent fuel management systems

NASA Technical Reports Server (NTRS)

English, T.; Miller, C.; Bullard, E.; Campbell, R.; Chockie, A.; Divita, E.; Douthitt, C.; Edelson, E.; Lees, L.

1977-01-01

The technical status of the old U.S. mailine program for high level radioactive nuclear waste management, and the newly-developing program for disposal of unreprocessed spent fuel was assessed. The method of long term containment for both of these waste forms is considered to be deep geologic isolation in bedded salt. Each major component of both waste management systems is analyzed in terms of its scientific feasibility, technical achievability and engineering achievability. The resulting matrix leads to a systematic identification of major unresolved technical or scientific questions and/or gaps in these programs.

Technical Feasibility of Enterotomy Closure with Knotless Barbed Suture Material (V-Loc 180) in Esophagojejunostomy Using Linear Stapler during Totally Laparoscopic Total Gastrectomy for Gastric Cancer.

PubMed

Kim, Dong Jin; Kim, Wook; Lee, Jun Hyun

2017-08-01

Intra-corporeal esophagojejunostomy (EJ) using a linear stapler creates a stapler entry hole that requires secure closure during the totally laparoscopic total gastrectomy (TLTG) procedure for gastric cancer. Since a standard method has not been established yet, the feasibility of using V-loc 180 (Covidien, Mansfield, MA, USA) suture material was evaluated in this study. During January 2012 to March 2015, 25 patients who underwent linear stapling EJ and V-loc 180 closure of remaining enterotomy were included in this study. Basic clinico-pathological characteristics, surgical outcomes, and short-term complications were analyzed. The mean patient age was 60.4 ± 8.5 years. Nineteen males and six females were included in this study. The mean body mass index was 25.3 ± 2.3 kg/m 2 . There were 22 stage-I, 2 stage-II, and 1 stage-III gastric cancer patients. The mean operation time was 240.5 ± 44.6 min, and the time for anastomosis was 38.8 ± 11.2 min. The procedures were successfully performed in all cases without any intra-operative complications. There was one case of EJ leakage that occurred at the corner of EJ staple line and not at the enterotomy closure site. The closure of the remaining enterotomy site using V-loc 180 suture following linear stapler EJ is technically feasible and safe during the TLTG procedure. However, further experience and results from other surgeons are necessary to generalize this procedure.

Statewide Curriculum Articulation Project for Vocational-Technical Education in Minnesota. Final Report.

ERIC Educational Resources Information Center

Burger, Laura J.; And Others

The goal of this project was to develop, validate, and utilize a process for vertically articulating curriculum between secondary and post secondary levels of vocational technical education throughout the state of Minnesota. Procedures involved the identification of two areas of staff responsibility: research and development, and service to local…

Charlotte Circle Outreach. Final Report.

ERIC Educational Resources Information Center

Calhoun, Mary Lynne; Rose, Terry L.; Prendergast, Donna

This final report details the activities of the Charlotte Circle Outreach, a program designed to provide technical assistance and training to early intervention programs offering services to infants and young children with substantial disabilities, ages birth through two years. This mission was accomplished through cooperative planning with…

Final Technical Report - 300°C Capable Electronics Platform and Temperature Sensor System For Enhanced Geothermal Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Cheng-Po; Shaddock, David; Sandvik, Peter

2012-11-30

A silicon carbide (SiC) based electronic temperature sensor prototype has been demonstrated to operate at 300°C. We showed continuous operation of 1,000 hours with SiC operational amplifier and surface mounted discreet resistors and capacitors on a ceramic circuit board. This feasibility demonstration is a major milestone in the development of high temperature electronics in general and high temperature geothermal exploration and well management tools in particular. SiC technology offers technical advantages that are not found in competing technologies such as silicon-on-insulator (SOI) at high temperatures of 200°C to 300°C and beyond. The SiC integrated circuits and packaging methods can bemore » used in new product introduction by GE Oil and Gas for high temperature down-hole tools. The existing SiC fabrication facility at GE is sufficient to support the quantities currently demanded by the marketplace, and there are other entities in the United States and other countries capable of ramping up SiC technology manufacturing. The ceramic circuit boards are different from traditional organic-based electronics circuit boards, but the fabrication process is compatible with existing ceramic substrate manufacturing. This project has brought high temperature electronics forward, and brings us closer to commercializing tools that will enable and reduce the cost of enhanced geothermal technology to benefit the public in terms of providing clean renewable energy at lower costs.« less

Advanced Transportation System Studies Technical Area 2 (TA-2) Heavy Lift Launch Vehicle Development Contract. Volume 2; Technical Results

NASA Technical Reports Server (NTRS)

1995-01-01

The purpose of the Advanced Transportation System Studies (ATSS) Technical Area 2 (TA-2) Heavy Lift Launch Vehicle Development contract was to provide advanced launch vehicle concept definition and analysis to assist NASA in the identification of future launch vehicle requirements. Contracted analysis activities included vehicle sizing and performance analysis, subsystem concept definition, propulsion subsystem definition (foreign and domestic), ground operations and facilities analysis, and life cycle cost estimation. This document is Volume 2 of the final report for the contract. It provides documentation of selected technical results from various TA-2 analysis activities, including a detailed narrative description of the SSTO concept assessment results, a user's guide for the associated SSTO sizing tools, an SSTO turnaround assessment report, an executive summary of the ground operations assessments performed during the first year of the contract, a configuration-independent vehicle health management system requirements report, a copy of all major TA-2 contract presentations, a copy of the FLO launch vehicle final report, and references to Pratt & Whitney's TA-2 sponsored final reports regarding the identification of Russian main propulsion technologies.

Vehicle Integrated Prognostic Reasoner (VIPR) Final Report

NASA Technical Reports Server (NTRS)

Bharadwaj, Raj; Mylaraswamy, Dinkar; Cornhill, Dennis; Biswas, Gautam; Koutsoukos, Xenofon; Mack, Daniel

2013-01-01

A systems view is necessary to detect, diagnose, predict, and mitigate adverse events during the flight of an aircraft. While most aircraft subsystems look for simple threshold exceedances and report them to a central maintenance computer, the vehicle integrated prognostic reasoner (VIPR) proactively generates evidence and takes an active role in aircraft-level health assessment. Establishing the technical feasibility and a design trade-space for this next-generation vehicle-level reasoning system (VLRS) is the focus of our work.

75 FR 48273 - Technical Service Provider Assistance

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-10

... DEPARTMENT OF AGRICULTURE Natural Resources Conservation Service 7 CFR Part 652 RIN 0578-AA48 Technical Service Provider Assistance AGENCY: Natural Resources Conservation Service, United States Department of Agriculture. ACTION: Final rule; Correcting amendment. SUMMARY: The Natural Resources...

Flexible and experimentally feasible shortcut to quantum Zeno dynamic passage

NASA Astrophysics Data System (ADS)

Li, Wenlin; Zhang, Fengyang; Jiang, Yunfeng; Li, Chong; Song, Heshan

2016-10-01

We propose and discuss a theoretical scheme to speed up Zeno dynamic passage by an external acceleration Hamiltonian. This scheme is a flexible and experimentally feasible acceleration because the acceleration Hamiltonian does not adhere rigidly to an invariant relationship, whereas it can be a more general form ∑uj (t)Hcj. Here Hcj can be arbitrarily selected without any limitation, and therefore one can always construct an acceleration Hamiltonian by only using realizable Hcj. Applying our scheme, we finally design an experimentally feasible Hamiltonian as an example to speed up an entanglement preparation passage.

Remote autopsy services: A feasibility study on nine cases.

PubMed

Vodovnik, Aleksandar; Aghdam, Mohammad Reza F; Espedal, Dan Gøran

2017-01-01

Introduction We have conducted a feasibility study on remote autopsy services in order to increase the flexibility of the service with benefits for teaching and interdepartmental collaboration. Methods Three senior staff pathologists, one senior autopsy technician and one junior resident participated in the study. Nine autopsies were performed by the autopsy technician or resident, supervised by the primary pathologist, through the secure, double encrypted video link using Jabber Video (Cisco) with a high-speed broadband connection. The primary pathologist and autopsy room each connected to the secure virtual meeting room using 14″ laptops with in-built cameras (Hewlett-Packard). A portable high-definition web camera (Cisco) was used in the autopsy room. Primary and secondary pathologists independently interpreted and later compared gross findings for the purpose of quality assurance. The video was streamed live only during consultations and interpretation. A satisfaction survey on technical and professional aspects of the study was conducted. Results Independent interpretations of gross findings between primary and secondary pathologists yielded full agreement. A definite cause of death in one complex autopsy was determined following discussions between pathologists and reviews of the clinical notes. Our satisfaction level with the technical and professional aspects of the study was 87% and 97%, respectively. Discussion Remote autopsy services are found to be feasible in the hands of experienced staff, with increased flexibility and interest of autopsy technicians in the service as a result.

Social Science Research Institutes in the Quality American University. Final Technical Report.

ERIC Educational Resources Information Center

Totman, Theodore L.

The technical report presents a chapter outline and thesis summary of an investigation of social science research institutes in American universities. The bulk of the report presents the thesis in four sections. Section I proposes a typology of organized social research units (OSRUs) in the 11 universities studied. Dimensions used to classify the…

A Feasibility and Engineering Study of Extending Cable TV Programming to Surrounding Communities. Planning Grant Report.

ERIC Educational Resources Information Center

Lakeshore Technical Inst., Cleveland, WI.

This report chronicles planning grant activities undertaken by the Lakeshore Technical Institute (LTI) and documents findings of a study to determine the feasibility and costs of extending public and educational programs from the LTI campus in Cleveland, Wisconsin, to surrounding communities. The geographic service area, regional…

Surgical timing after chemoradiotherapy for rectal cancer, analysis of technique (STARRCAT): results of a feasibility multi-centre randomized controlled trial.

PubMed

Foster, J D; Ewings, P; Falk, S; Cooper, E J; Roach, H; West, N P; Williams-Yesson, B A; Hanna, G B; Francis, N K

2016-10-01

The optimal time of rectal resection after long-course chemoradiotherapy (CRT) remains unclear. A feasibility study was undertaken for a multi-centre randomized controlled trial evaluating the impact of the interval after chemoradiotherapy on the technical complexity of surgery. Patients with rectal cancer were randomized to either a 6- or 12-week interval between CRT and surgery between June 2012 and May 2014 (ISRCTN registration number: 88843062). For blinded technical complexity assessment, the Observational Clinical Human Reliability Analysis technique was used to quantify technical errors enacted within video recordings of operations. Other measured outcomes included resection completeness, specimen quality, radiological down-staging, tumour cell density down-staging and surgeon-reported technical complexity. Thirty-one patients were enrolled: 15 were randomized to 6 and 16-12 weeks across 7 centres. Fewer eligible patients were identified than had been predicted. Of 23 patients who underwent resection, mean 12.3 errors were observed per case at 6 weeks vs. 10.7 at 12 weeks (p = 0.401). Other measured outcomes were similar between groups. The feasibility of measurement of operative performance of rectal cancer surgery as an endpoint was confirmed in this exploratory study. Recruitment of sufficient numbers of patients represented a challenge, and a proportion of patients did not proceed to resection surgery. These results suggest that interval after CRT may not substantially impact upon surgical technical performance.

FBI fingerprint identification automation study. AIDS 3 evaluation report. Volume 2: Technical feasibility

NASA Technical Reports Server (NTRS)

Mulhall, B. D. L.

1980-01-01

The results of this effort are presented in a manner for use by both the AIDS 3 Operational and Economic Feasibility subtasks as well as the Development of Alternative subtask. The approach taken was to identify the major functions that appear in AIDS 3 and then to determine which technologies would be needed for support. The technologies were then examined from the point of view of reliability, throughput, security, availability, cost and possible future trends. Whenever possible graphs are given to indicate projected costs of rapidly changing technologies.

Renewable Fuel Standard Program (RFS1): Final Rule Additional Resources

EPA Pesticide Factsheets

The final rule of fuels and fuel additives: renewable fuel standard program is published on May 1, 2007 and is effective on September 1, 2007. You will find the links to this final rule and technical amendments supporting this rule.

Treatment of Biliary Stricture After Live Donor Liver Transplantation With Combined Metal and Plastic Stent Insertion: A Feasibility and Safety Study.

PubMed

Parlak, Erkan; Koksal, Aydin Seref; Eminler, Ahmet Tarik; Toka, Bilal; Uslan, Mustafa Ihsan

2017-08-01

Fully covered self-expandable metal stents (Fc-SEMSs) have a challenging use in the treatment of anastomosis strictures after live donor liver transplantation (LDLT) because they can occlude secondary branch biliary ducts when placed above the biliary bifurcation. In this study, we evaluated the technical feasibility and safety of combining Fc-SEMSs with plastic stent(s) inserted to the secondary branch biliary ducts for the treatment of anastomosis stricture after LDLT. The study group included 22 patients (12 men, aged 51±11 years) with anastomotic biliary stricture after LDLT. A Fc-SEMS, 8 to 10 mm in diameter, was inserted to the straight, dilated main duct and plastic stent(s) were inserted to the secondary branches to avoid their occlusion. Stents were left in place for 2 months and removed with a stent retrieving forceps. Technical feasibilities, including technical success, successful removal, and adverse events of this novel strategy, were evaluated. Fc-SEMSs were successfuly deployed and removed in all of the cases. Three (13.6%) patients had pain requiring intravenous analgesia and Fc-SEMS had to be removed because of unbearable pain in one of them. Three (13.6%) patients developed cholangitis due to occlusion of unrecognized secondary branch biliary ducts. Primary stricture resolution rate was achieved in 17 (89.5%) of 19 patients. Recurrence was observed in 3 (17.6%) patients after a mean follow-up duration of 154.3±52.6 (range, 104-304) days. Combination of Fc-SEMS and plastic stent(s) is technically feasible and safe for the treatment of anastomotic biliary strictures after LDLT.

Technical writing versus technical writing

NASA Technical Reports Server (NTRS)

Dillingham, J. W.

1981-01-01

Two terms, two job categories, 'technical writer' and 'technical author' are discussed in terms of industrial and business requirements and standards. A distinction between 'technical writing' and technical 'writing' is made. The term 'technical editor' is also considered. Problems inherent in the design of programs to prepare and train students for these jobs are discussed. A closer alliance between industry and academia is suggested as a means of preparing students with competent technical communication skills (especially writing and editing skills) and good technical skills.

Solar Heating and Cooling of Buildings: Phase 0. Executive Summary. Final Report.

ERIC Educational Resources Information Center

Westinghouse Electric Corp., Baltimore, MD.

After the Westinghouse Electric Corporation made a comprehensive analysis of the technical, economic, social, environmental, and institutional factors affecting the feasibility of utilizing solar energy for heating and cooling buildings, it determined that solar heating and cooling systems can become competitive in most regions of the country in…

Technical and financial feasibility of an inferior vena cava filter retrieval program at a level one trauma center.

PubMed

Charlton-Ouw, Kristofer M; Leake, Samuel S; Sola, Cristina N; Sandhu, Harleen K; Albarado, Rondel; Holcomb, John B; Miller, Charles C; Safi, Hazim J; Azizzadeh, Ali

2015-01-01

Considering new guidelines for retrievable inferior vena cava filters (IVCFs), we examine our initial experience after establishing a comprehensive filter removal program in our level 1 trauma center. We evaluated the technical and financial feasibility of this program and barriers to IVCF retrieval, including insurance status and costs, in trauma patients. Trauma patients receiving IVCFs from May 2011 to 2013 were consented and prospectively enrolled in the study program. Retrieval rates were assessed for the years before study initiation. Primary outcome was IVCF retrieval. Hospital financial data for retrieval were examined and univariate analysis performed. Hospital cost-to-charge and payment-to-charge ratios were assessed. Before study initiation from April 2009 to 2011, 66 IVCFs were placed in trauma patients with only 2 retrievals in 2 years. During the study period, 247 trauma patients had IVCF placement of which 111 (45%) were enrolled. The main reason for nonenrollment was lack of referral by the implanting team. Retrieval was attempted in 100 outpatients with success in 85 (85%). Patients enrolled in the program were more likely to have their filters removed (73% vs. 18%; odds ratio, 12.6; 95% confidence interval, 6.6-24.3; P < 0.001). Mean time from placement to attempt was 6.2 ± 4.0 months (range, 0.5-31.8). Of the total attempts, 29% were nonresource patients, 11% had Medicaid, and 60% had commercial insurance including Medicare patients. Chances of successful retrieval were higher if performed later during the study (P = 0.03). Successful retrieval was not related to insurance status (P = not significant). The mean total hospital charges related to retrieval were $4,493 (range, $2,510-$9,106). Successful retrieval contributed to lower total charges (P < 0.01). Factors contributing to higher total charges were retrieval attempt later in study period (P = 0.01) and commercial insurance status (P = 0.04). The rate of IVCF placement in trauma patients

Presurgical motor, somatosensory and language fMRI: Technical feasibility and limitations in 491 patients over 13 years.

PubMed

Tyndall, Anthony J; Reinhardt, Julia; Tronnier, Volker; Mariani, Luigi; Stippich, Christoph

2017-01-01

To analyse the long-term feasibility and limitations of presurgical fMRI in a cohort of tumour and epilepsy patients with different MR-scanners at 1.5 and 3.0 T. Four hundred and ninety-one consecutive patients undergoing presurgical fMRI between 2000 and 2012 on five different MR-scanners using established paradigms and semi-automated data processing were included. Success rates of task performance and BOLD-activation were determined for motor and somatosensory somatotopic mapping and language localisation. Procedural success, failures and imaging artifacts were analysed. MR-field strengths were compared. Two thousand three hundred fifteen of 2348 (98.6 %) attempted paradigms (1033 motor, 1220 speech, 95 somatosensory) were successfully performed. 100 paradigms (4.3 %) were repetition runs. 23 speech, 6 motor and 2 sensory paradigms failed for non-compliance and technical issues. Most language paradigm failures were noted in overt sentence generation. Average significant BOLD-activation was higher for motor than language paradigms (95.8 vs. 81.6 %). Most language paradigms showed significantly higher activation rates at 3 T compared to 1.5 T, whereas no significant difference was found for motor paradigms. fMRI proved very robust for the presurgical localisation of the different motor and somatosensory body representations, as well as Broca's and Wernicke's language areas across different MR-scanners at 1.5 and 3.0 T over 13 years. • Standardised presurgical motor and language fMRI is robust across various MRI platforms. • Motor fMRI is less dependent on field strength than language fMRI. • fMRI task failures are relatively low and are reduced by paradigm repetition.

State Compensatory Education. Final Technical Report 1975-76. Appendixes.

ERIC Educational Resources Information Center

Austin Independent School District, TX. Office of Research and Evaluation.

This material consists of ten appendixes to the Final Report for 1976-77 on the implementation of the Texas state-supported compensatory education program in the Austin Independent School District as evaluated by that district's Office of Research and Evaluation. The instruments used in the evaluation process are described or presented in full,…

Feasibility of robot-assisted modified radical neck dissection by post-auricular facelift approach.

PubMed

Tae, K; Ji, Y B; Song, C M; Sung, E S; Chung, J H; Lee, S H; Park, H J

2016-11-01

The aim of this study was to evaluate the technical feasibility and safety of robot-assisted modified radical neck dissection (MRND) for head and neck cancer patients with a clinically node-positive neck. The cases of 10 head and neck cancer patients who underwent unilateral therapeutic robot-assisted MRND by post-auricular facelift approach were analyzed. The robot-assisted MRND was completed successfully in all patients without any conversion to conventional neck dissection. The mean number of lymph nodes removed was 36.7±8.6. The mean duration of surgery for robot-assisted MRND was 274±65min (range 175-395min). Transient marginal nerve palsy occurred in two patients and partial necrosis of the skin flap occurred in one patient. In terms of cosmetic satisfaction, 70% of patients were very satisfied or satisfied with postoperative cosmesis. In conclusion, robot-assisted MRND by post-auricular facelift approach is technically feasible and safe in selected patients with head and neck cancer, and yields excellent postoperative cosmesis. Copyright © 2016 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Feasibility of Urban Service Opportunity and Curricular Amplification: "The St. Louis Project." Final Report.

ERIC Educational Resources Information Center

Guthrie, Robert V.; And Others

A study was made to test the feasibility of a small college (located some distance from a city) establishing a residence unit within a slum or transitional area of a city. The purposes of such a program, in which students and faculty live in the city while continuing their normal course work, would be to: (1) enhance the curriculum by broadening…

77 FR 18716 - Transportation Security Administration Postal Zip Code Change; Technical Amendment

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-28

... organizational changes and it has no substantive effect on the public. DATES: Effective March 28, 2012. FOR... No. 1572-9] Transportation Security Administration Postal Zip Code Change; Technical Amendment AGENCY: Transportation Security Administration, DHS. ACTION: Final rule. SUMMARY: This rule is a technical change to...

Direct solar pumping of semiconductor lasers: A feasibility study

NASA Technical Reports Server (NTRS)

Anderson, Neal G.

1991-01-01

The primary goals of the feasibility study are the following: (1) to provide a preliminary assessment of the feasibility of pumping semiconductor lasers in space directly focused sunlight; and (2) to identify semiconductor laser structures expected to operate at the lowest possible focusing intensities. It should be emphasized that the structures under consideration would provide direct optical-to-optical conversion of sunlight into laser light in a single crystal, in contrast to a configuration consisting of a solar cell or battery electrically pumping a current injection laser. With external modulation, such lasers may prove to be efficient sources for intersatellite communications. We proposed to develop a theoretical model of semiconductor quantum-well lasers photopumped by a broadband source, test it against existing experimental data where possible, and apply it to estimating solar pumping requirements and identifying optimum structures for operation for operation at low pump intensities. This report outlines our progress toward these goals. Discussion of several technical details are left to the attached summary abstract.

TEAM TRAINING. FINAL TECHNICAL REPORT FEBRUARY 1966-FEBRUARY 1967.

ERIC Educational Resources Information Center

BRIGGS, GEORGE E.; JOHNSTON, WILLIAM A.

THIS IS THE FINAL REPORT ON A FOUR-YEAR PROGRAM OF LABORATORY RESEARCH ON TEAM TRAINING IN A COMBAT INFORMATION CENTER (CIC) CONTEXT. THE RESEARCH LITERATURE ON TEAM TRAINING IS REVIEWED, AND A SET OF CONCLUSIONS IS DRAWN WITH REGARD TO TEAM PERFORMANCE AS A FUNCTION OF TASK, TRAINING, AND COMMUNICATIONS VARIABLES. IN ADDITION, THE IMPLICATIONS…

Feasibility Analysis For Heating Tribal Buildings with Biomass

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steve Clairmont; Micky Bourdon; Tom Roche

2009-03-03

This report provides a feasibility study for the heating of Tribal buildings using woody biomass. The study was conducted for the Confederated Salish and Kootenai Tribes of the Flathead Reservation in western Montana. S&K Holding Company and TP Roche Company completed the study and worked together to provide the final report. This project was funded by the DOE's Tribal Energy Program.

Are health-based payments a feasible tool for addressing risk segmentation?

PubMed

Rogal, D L; Gauthier, A K

1998-01-01

As they attempt to increase health insurance coverage and improve the efficiency of the market, researchers, policymakers, and health plan representatives have been addressing the issue of risk segmentation. Many risk assessment tools and risk-adjusted payment methodologies have been developed and demonstrated for a variety of populations and payers experiencing various market constraints. The evidence shows that risk-adjusted payments are feasible for most populations receiving acute care, while technical obstacles, political issues, and some research gaps remain.

Feasible way of Human Solid and Liquid Wastes' Inclusion Into Intersystem Mass Exchange of Biological-Technical Life Support Systems

NASA Astrophysics Data System (ADS)

Ushakova, Sofya; Tikhomirov, Alexander A.; Tikhomirova, Natalia; Kudenko, Yurii; Griboskaya, Illiada; Gros, Jean-Bernard; Lasseur, Christophe

The basic objective arising at use of mineralized human solid and liquid wastes serving as the source of mineral elements for plants cultivation in biological-technical life support systems appears to be NaCl presence in them. The given work is aimed at feasibility study of mineralized human metabolites' utilization for nutrient solutions' preparation for their further employment at a long-term cultivation of uneven-aged wheat and Salicornia europaea L. cenosis in a conveyer regime. Human solid and liquid wastes were mineralized by the "wet incineration" method developed by Yu. Kudenko. On their base the solutions were prepared which were used for cultivation of 5-aged wheat conveyer with the time step-interval of 14 days. Wheat was cultivated by hydroponics method on expanded clay aggregate. For partial demineralization of nutrient solution every two weeks after regular wheat harvesting 12 L of solution was withdrawn from the wheat irrigation tank and used for Salicornia europaea cultivation by the water culture method in a conveyer regime. The Salicornia europaea conveyer was represented by 2 ages with the time step-interval of 14 days. Resulting from repeating withdrawal of the solution used for wheat cultivation, sodium concentration in the wheat irrigation solution did not exceed 400 mg/l, and mineral elements contained in the taken solution were used for Salicornia europaea cultivation. The experiment lasted 7 months. Total wheat biomass productivity averaged 30.1 g*m-2*day-1 at harvest index equal to 36.8The work was carried out under support of SB RAS grant 132 and INTAS 05-1000008-8010

A study to examine the feasibility of using surface penetrators for mineral exploration

NASA Technical Reports Server (NTRS)

Davis, A. S.; Anderson, D. W.

1978-01-01

The feasibility of using penetrators in earth applications is examined. Penetrator applications in exploration for mineral resources only is summarized. Instrumentation for future penetrators is described. Portions of this report are incorporated into a more extensive report examining other penetrator applications in exploration for fossil fuels, geothermal resources, and in environmental and engineering problems, which is to be published as a NASA technical publication.

Dissemination of Continuing Education Materials Via Television Delivery Systems. Final Technical Report and Final Report.

ERIC Educational Resources Information Center

Munushian, Jack

In 1972, the University of Southern California School of Engineering established a 4-channel interactive instructional television network. It was designed to allow employees of participating industries to take regular university science and engineering courses and special continuing education courses at or near their work locations. Final progress…

Illinois Clean Coal Institute 2005 annual report. Final technical report for the period September 1st, 2004, through August 31, 2005 on projects funded by the Illinois Department of Commerce and Economic Opportunity

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

2005-11-08

This final technical report contains the abstracts and executive summaries of projects funded through the Illinois Clean Coal Institute solicitation entitled 'Request for proposals No. 04-1(ICCI/RFP04-1)'. Support of these projects is by the Office of Coal Development and Department of Commerce and Economic Opportunity. The projects fall into the following categories: advanced coal mining technologies; coal preparation and coal production business practice; management of coal combustion byproducts; commercialization and technology transfer. Final project extensions are also recorded.

Pascua Yaqui Tribe Renewable Energy Development and Deployment Feasibility Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arvayo, Maria

In 2012, PYT was awarded a grant from the Department of Energy Tribal Energy Program to conduct a Renewable Energy Development and Deployment Feasibility Study that would define the technical and economic viability of renewable energy on tribal lands. Red Mountain Energy Partners (RMEP) was hired by PYT to complete the study. Through this study, Red Mountain concluded that there are viable opportunities for solar at Tortuga Ranch, the Casino del Sol and a third site near the Justice Center on Camino de Oeste.

SeaWiFS Technical Report Series. Volume 43; SeaWiFS Prelaunch Technical Report Series Final Cumulative Index

NASA Technical Reports Server (NTRS)

Firestone, Elaine R. (Editor); Hooker, Stanford B.

1998-01-01

The Sea-viewing Wide Field-of-view Sensor (SeaWiFS) is the follow-on ocean color instrument to the Coastal Zone Color Scanner (CZCS), which ceased operations in 1986, after an eight-year mission. SeaWiFS was launched on 1 August 1997, on the SeaStar satellite, built by Orbital Sciences Corporation (OSC). The SeaWiFS Project at the National Aeronautics and Space Administration (NASA) Goddard Space Flight Center (GSFC), undertook the responsibility of documenting all aspects of this mission, which is critical to the ocean color and marine science communities. This documentation, entitled the SeaWiFS Technical Report Series, is in the form of NASA Technical Memorandum Number 104566 and 1998-104566. All reports published are volumes within the series. This particular volume, which is the last of the so-called Prelaunch Series serves as a reference, or guidebook, to the previous 42 volumes and consists of 6 sections including: an addenda, an errata, an index to key words and phrases, lists of acronyms and symbols used, and a list of all references cited. The editors have published a cumulative index of this type after every five volumes. Each index covers the reference topics published in all previous editions, that is, each new index includes all of the information contained in the preceding indexes with the exception of any addenda.

Non-Technical Skills for Surgeons (NOTSS): Critical appraisal of its measurement properties.

PubMed

Jung, James J; Borkhoff, Cornelia M; Jüni, Peter; Grantcharov, Teodor P

2018-02-17

To critically appraise the development and measurement properties, including sensibility, reliability, and validity of the Non-Technical Skills of Surgeons (NOTSS) system. Articles that described development process of the NOTSS system were identified. Relevant primary studies that presented evidence of reliability and validity were identified through a comprehensive literature review. NOTSS was developed through robust item generation and reduction strategies. It was shown to have good content validity, acceptability, and feasibility. Inter-rater reliability increased with greater expertise and number of assessors. Studies demonstrated evidence of cross-sectional construct validity, in that the tool was able to differentiate known groups of varied non-technical skill levels. Evidence of longitudinal construct validity also existed to demonstrate that NOTSS detected changes in non-technical skills before and after targeted training. In populations and settings presented in our critical appraisal, NOTSS provided reliable and valid measurements of intraoperative non-technical skills of surgeons. Copyright © 2018 Elsevier Inc. All rights reserved.

INDEPENDENT TECHNICAL REVIEW OF THE FOCUSED FEASIBILITY STUDY AND PROPOSED PLAN FOR DESIGNATED SOLID WASTE MANAGEMENT UNITS CONTRIBUTING TO THE SOUTHWEST GROUNDWATER PLUME AT THE PADUCAH GASEOUS DIFFUSION PLANT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Looney, B.; Eddy-Dilek, C.; Amidon, M.

2011-05-31

The U. S. Department of Energy (DOE) is currently developing a Proposed Plan (PP) for remediation of designated sources of chlorinated solvents that contribute contamination to the Southwest (SW) Groundwater Plume at the Paducah Gaseous Diffusion Plant (PGDP), in Paducah, KY. The principal contaminants in the SW Plume are trichloroethene (TCE) and other volatile organic compounds (VOCs); these industrial solvents were used and disposed in various facilities and locations at PGDP. In the SW plume area, residual TCE sources are primarily in the fine-grained sediments of the Upper Continental Recharge System (UCRS), a partially saturated zone that delivers contaminants downwardmore » into the coarse-grained Regional Gravel Aquifer (RGA). The RGA serves as the significant lateral groundwater transport pathway for the plume. In the SW Plume area, the four main contributing TCE source units are: (1) Solid Waste Management Unit (SWMU) 1 / Oil Landfarm; (2) C-720 Building TCE Northeast Spill Site (SWMU 211A); (3) C-720 Building TCE Southeast Spill Site (SWMU 211B); and (4) C-747 Contaminated Burial Yard (SWMU 4). The PP presents the Preferred Alternatives for remediation of VOCs in the UCRS at the Oil Landfarm and the C-720 Building spill sites. The basis for the PP is documented in a Focused Feasibility Study (FFS) (DOE, 2011) and a Site Investigation Report (SI) (DOE, 2007). The SW plume is currently within the boundaries of PGDP (i.e., does not extend off-site). Nonetheless, reasonable mitigation of the multiple contaminant sources contributing to the SW plume is one of the necessary components identified in the PGDP End State Vision (DOE, 2005). Because of the importance of the proposed actions DOE assembled an Independent Technical Review (ITR) team to provide input and assistance in finalizing the PP.« less

Feasibility study of rainwater harvesting for domestic use (Case study: West Jakarta rainfall data)

NASA Astrophysics Data System (ADS)

Kartolo, Jason; Kusumawati, Elly

2017-11-01

Rainwater Harvesting system is one of considerable choice to reduce flood in Jakarta, moreover it helps to reduce main tap water consumption. In this study, rainwater is used for flushing toilet and watering garden for domestic use. Rainwater harvesting system is examined for 60 m2 and 90 m2 housing area, using rainfall data from Cengkareng station in West Jakarta. Two type of rainwater harvesting reservoir is designed, those are ground reservoir and underground reservoir. From the analysis, it finds that 60 m2 house feasible for 1 m3 ground reservoir and 9 m3 underground reservoir. Meanwhile for 90 m2 house 2 m3 tanks ground reservoir and 14 m3 tank underground reservoir is feasible. Underground reservoir retain more water volume so it provide higher rate of water supply. The cost of underground reservoir is lower 60% - 70% than ground reservoir. Even though rainwater harvesting is technically feasible for housing, it is not economically feasible. The construction cost is higher than the benefit of reduced tap water consumption.

Technical/ administrative options for managing tritium MCL exceedances in P-area groundwater and Steel Creek

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ross, J.

2017-04-01

This white paper was requested by the Core Team (United States Department of Energy [USDOE], United States Environmental Protection Agency [USEPA], and South Carolina Department of Health and Environmental Control [SCDHEC]) at the P-Area Groundwater (PAGW) Operable Unit (OU) Scoping Meeting held in January 2017 to discuss recent data and potential alternatives in support of a focused Corrective Measures Study/Feasibility Study (CMS/FS). This white paper presents an overview of the problem, and a range of technical and administrative options for addressing the tritium contamination in groundwater and Steel Creek. As tritium cannot be treated practicably, alternatives are limited to mediamore » transfer, containment and natural attenuation principally relying on radioactive decay. Using other groundwater OU decisions involving tritium as precedent, Savannah River Nuclear Solutions (SRNS) recommends that final tritium alternatives be evaluated in a CMS/FS, understanding that the likely preferred remedy will include natural attenuation with land use controls (LUCs). This is based on the inability to significantly reduce tritium impact to Steel Creek using an engineered solution as compared to natural attenuation. The timing of this evaluation could be conducted concurrently with the final remedy evaluation for volatile organic compounds (VOCs).« less

A technical case report on use of tubular retractors for anterior cervical spine surgery.

PubMed

Kulkarni, Arvind G; Patel, Ankit; Ankith, N V

2017-12-19

The authors put-forth this technical report to establish the feasibility of performing an anterior cervical corpectomy and fusion (ACCF) and a two-level anterior cervical discectomy and fusion (ACDF) using a minimally invasive approach with tubular retractors. First case: cervical spondylotic myelopathy secondary to a large postero-inferiorly migrated disc treated with corpectomy and reconstruction with a mesh cage and locking plate. Second case: cervical disc herniation with radiculopathy treated with a two-level ACDF. Both cases were operated with minimally invasive approach with tubular retractor using a single incision. Technical aspects and clinical outcomes have been reported. No intra or post-operative complications were encountered. Intra-operative blood loss was negligible. The patients had a cosmetic scar on healing. Standard procedure of placement of tubular retractors is sufficient for adequate surgical exposure with minimal invasiveness. Minimally invasive approach to anterior cervical spine with tubular retractors is feasible. This is the first report on use of minimally invasive approach for ACCF and two-level ACDF.

Conjugated ionomers for photovoltaic applications: electric field driven charge separation in organic photovoltaics. Final Technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lonergan, Mark

Final technical report for Conjugated ionomers for photovoltaic applications, electric field driven charge separation in organic photovoltaics. The central goal of the work we completed was been to understand the photochemical and photovoltaic properties of ionically functionalized conjugated polymers (conjugated ionomers or polyelectrolytes) and energy conversion systems based on them. We primarily studied two classes of conjugated polymer interfaces that we developed based either upon undoped conjugated polymers with an asymmetry in ionic composition (the ionic junction) or doped conjugated polymers with an asymmetry in doping type (the p-n junction). The materials used for these studies have primarily been themore » polyacetylene ionomers. We completed a detailed study of p-n junctions with systematically varying dopant density, photochemical creation of doped junctions, and experimental and theoretical work on charge transport and injection in polyacetylene ionomers. We have also completed related work on the use of conjugated ionomers as interlayers that improve the efficiency or organic photovoltaic systems and studied several important aspects of the chemistry of ionically functionalized semiconductors, including mechanisms of so-called "anion-doping", the formation of charge transfer complexes with oxygen, and the synthesis of new polyfluorene polyelectrolytes. We also worked worked with the Haley group at the University of Oregon on new indenofluorene-based organic acceptors.« less

Santa Barbara Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hacker, Angela; Hansen, Sherman; Watkins, Ashley

2013-11-30

This report serves as the Final Report for Santa Barbara County’s Energy Efficiency and Conservation Block Grant (EECBG) BetterBuildings Neighborhood Program (BBNP) award from the U.S. Department of Energy (DOE). This report explains how DOE BBNP funding was invested to develop robust program infrastructure designed to help property owners complete energy improvements, thereby generating substantial outcomes for the local environment and economy. It provides an overview of program development and design within the grant period, program accomplishments and challenges to date, and a plan for the future sustainability of emPower, the County’s innovative clean energy and building efficiency program. Duringmore » the grant period, Santa Barbara County’s emPower program primarily targeted 32,000 owner occupied, single family, detached residential homes over 25 years old within the County. In order to help these homeowners and their contractors overcome market barriers to completing residential energy improvements, the program developed and promoted six voluntary, market-based service areas: 1) low cost residential financing (loan loss reserve with two local credit unions), 2) residential rebates, 3) local customer service, 4) expert energy advising, 5) workforce development and training, and 6) marketing, education and outreach. The main goals of the program were to lower building energy use, create jobs and develop a lasting regional building performance market. These services have generated important early outcomes and lessons after the program’s first two years in service. The DOE BBNP funding was extended through October 2014 to enable Santa Barbara County to generate continued outcomes. In fact, funding related to residential financing remains wholly available for the foreseeable future to continue offering Home Upgrade Loans to approximately 1,300 homeowners. The County’s investment of DOE BBNP funding was used to build a lasting, effective, and

Final Technical Report for Quantum Embedding for Correlated Electronic Structure in Large Systems and the Condensed Phase

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chan, Garnet Kin-Lic

2017-04-30

This is the final technical report. We briefly describe some selected results below. Developments in density matrix embedding. DMET is a quantum embedding theory that we introduced at the beginning of the last funding period, around 2012-2013. Since the first DMET papers, which demonstrated proof-of- principle calculations on the Hubbard model and hydrogen rings, we have carried out a number of different developments, including: Extending the DMET technology to compute broken symmetry phases, including magnetic phases and super- conductivity (Pub. 13); Calibrating the accuracy of DMET and its cluster size convergence against other methods, and formulation of a dynamical clustermore » analog (Pubs. 4, 10) (see Fig. 1); Implementing DMET for ab-initio molecular calculations, and exploring different self-consistency criteria (Pubs. 9, 14); Using embedding to defi ne quantum classical interfaces Pub. 2; Formulating DMET for spectral functions (Pub. 7) (see Fig. 1); Extending DMET to coupled fermion-boson problems (Pub. 12). Together with these embedding developments, we have also implemented a wide variety of impurity solvers within our DMET framework, including DMRG (Pub. 3), AFQMC (Pub. 10), and coupled cluster theory (CC) (Pub. 9).« less

Congeneration feasibility: Otis Elavator Company and Polychrome Corporation

NASA Astrophysics Data System (ADS)

Fox, H.

1982-05-01

An investigation of the technical and economic feasibility of cogenerating electric and thermal power at two manufacturing plants (Otis Elevator Company and Polychrome Corporation) located on neighboring properties in Yonkers, NY is discussed. Existing electrical and steam producing equipment and energy consumption date are summarized. Alternative cases examined include electrical energy generation, electrical energy generation with waste heat recovery and a combined cycle case. Also reported are life cycle cost economic evaluations including simple payback period and return on investment indices. While it was concluded that cogeneration of heat and electricity at these industrial plant sites would not be economically viable, this detailed study provides valuable insights.

Low-Cost Computer-Aided Instruction/Computer-Managed Instruction (CAI/CMI) System: Feasibility Study. Final Report.

ERIC Educational Resources Information Center

Lintz, Larry M.; And Others

This study investigated the feasibility of a low cost computer-aided instruction/computer-managed instruction (CAI/CMI) system. Air Force instructors and training supervisors were surveyed to determine the potential payoffs of various CAI and CMI functions. Results indicated that a wide range of capabilities had potential for resident technical…

Final Revisions Rule State Budgets and New Unit Set-Asides TSD

EPA Pesticide Factsheets

This technical support document shows the underlying data and calculations used to quantify the state budget revisions and new unit set-aside revisions made in the final revisions rule, as well as those revisions included in the direct final revisions rule

A System for Evaluating Microcomputer Courseware for Vocational and Technical Education. Final Report.

ERIC Educational Resources Information Center

Chase, Shirley A.; And Others

A project was conducted to design a system for evaluating microcomputer courseware for vocational and technical education. Through a literature review and contacts with organizations and individuals involved in courseware evaluation and use, project staff identified and acquired for review documents pertaining to courseware evaulation, vocational…

Scaling Studies for Advanced High Temperature Reactor Concepts, Final Technical Report: October 2014—December 2017

DOE Office of Scientific and Technical Information (OSTI.GOV)

Woods, Brian; Gutowska, Izabela; Chiger, Howard

core with an electrical heat source. The peak core region temperature capability is 1400°C. As part of this project, an inventory of test facilities that could be used for these experimental programs was completed. Several of these facilities showed some promise, however, upon further investigation it became clear that only the OSU HTTF had the power and/or peak temperature limits that would allow for the experimental programs envisioned herein. Thus the conceptual design and feasibility study development focused on examining the feasibility of configuring the current HTTF to collect validation data for these experimental programs. In addition to the scaling analyses and conceptual design development, a test plan was developed for the envisioned modified test facility. This test plan included a discussion on an appropriate shakedown test program as well as the specific matrix tests. Finally, a feasibility study was completed to determine the cost and schedule considerations that would be important to any test program developed to investigate these designs and events.« less

Investigating the feasibility of a reuse scenario for textile fibres recovered from end-of-life tyres.

PubMed

Landi, Daniele; Gigli, Silvia; Germani, Michele; Marconi, Marco

2018-05-01

The management of end-of-life tyres (ELTs) is regulated by several national and international legislations aiming to promote the recovery of materials and energy from this waste. The three main materials used in tyres are considered: rubber (main product), which is currently reused in other closed-loop applications; steel, which is used for the production of virgin materials; and textile fibres (approximately 10% by weight of ELTs), which are mainly incinerated for energy recovery (open-loop scenario). This study aims to propose and validate a new closed-loop scenario for textile fibres based on material reuse for bituminous conglomerates. The final objective is to verify the technical, environmental, financial, and economic feasibility of the proposed treatment process and reuse scenario. After characterization of the textile material, which is required to determine the technological feasibility, a specific process has been developed to clean, compact, and prepare the fibres for subsequent reuse. A life cycle assessment (LCA) has been carried out to quantify the environmental benefits of reusing the fibres. Finally, a cost benefit analysis based on the LCA results was conducted to establish the long-term financial and economic sustainability. From a technological point of view, the tyre textile fibres could be a promising substitute to the reinforcement cellulose commonly used in asphalts as long as the fibres are properly prepared (compaction and pellet production) for application in the standard bituminous conglomerate production process. From an environmental point of view, relevant benefits in terms of global warming potential and acidification potential reduction were observed in comparison with the standard incineration for energy recovery (respectively -86% and -45%). Moreover, the proposed scenario can be considered as financially viable in the medium to long term (cumulative generated cash flow is positive after the 5th year) and economically sustainable

Feasibility Study of the Development of a Specialized Computer System of Organic Chemical Signatures of Spectral Data.

ERIC Educational Resources Information Center

Scholtz, R. G.; And Others

This final report of a feasibility study describes the research performed in assessing the requirements for a chemical signature file and search scheme for organic compound identification and information retrieval. The research performed to determined feasibility of identifying an unknown compound involved screening the compound against a file of…

A Planning Study for the Conversion of Recorded Books and Magazines from Rigid Discs to Cassettes and Flexible Discs. Final Report.

ERIC Educational Resources Information Center

Innovative Systems Research, Inc., Pennsauken, NJ.

Twelve different conversion plans were delineated and evaluated in the performance of this study effort. An indepth technical, financial, and cost/benefit analysis was included. One plan was determined to be distinctively more cost-effective than any of the other plans because it provided a technically feasible system that assured the maximum…

Joint distraction for thumb carpometacarpal osteoarthritis: a feasibility study with 1-year follow-up.

PubMed

Spaans, Anne J; Minnen, L Paul van; Braakenburg, Assa; Mink van der Molen, Aebele B

2017-08-01

The purpose of this pilot study was to evaluate the feasibility of joint distraction of the first carpometacarpal (CMC1) joint in patients with CMC1 osteoarthritis (OA). An external joint distractor was placed over the CMC1 joint by K-wire fixation in the trapezium and the metacarpal. The joint was distracted 3 mm during surgery. The device was then kept in place for 8 weeks. Disabilities of the Arm, Shoulder, and Hand (DASH) score, Michigan Hand Outcome Questionnaire (MHQ), Visual Analogue Scale (VAS), and grip strength were recorded preoperatively and at set postoperative intervals. Five female patients with an average age of 53 years (range = 41-61) were included. One year postoperatively, average DASH, MHQ, and VAS scores improved compared to preoperative values; DASH 53 to 27, MHQ 48 to 76, and VAS pain 48 to 14. There were no technical problems associated with the device. One patient had a local pin site infection treated successfully with oral antibiotics. This study concludes that joint distraction of the osteoarthritic CMC1 joint is technically feasible. In this small, prospective pilot study the majority of the results were favourable during short-term follow-up.

Wyoming Deaf/Blind Grant. Final Report.

ERIC Educational Resources Information Center

Whitson, Joanne B.

This final report describes activities and accomplishments of the Wyoming Deaf-Blind Grant, a 3-year federally supported project to identify children who have deaf-blindness and to provide technical assistance in the development of educational services for these children. Major accomplishments of the project included: identification of more…

A Feasibility Study of Computer Assisted Instruction in US Army Basic Electronics Training. Final Report.

ERIC Educational Resources Information Center

International Business Machines Corp., Gaithersburg, MD. Federal Systems Div.

A study of computer-assisted instruction (CAI) for US Army basic electronics training at the US Army Signal Center and School establishes the feasibility of CAI as a training technique. Three aspects of CAI are considered: effectiveness, efficiency, and applicability of CAI to basic electronics training. The study explores the effectiveness of the…

Final Technical Report for DE-SC0012297

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dell'Antonio, Ian

This is the final report on the work performed in award DE-SC0012297, Cosmic Frontier work in support of the LSST Dark Energy Science Collaboration's work to develop algorithms, simulations, and statistical tests to ensure optimal extraction of the dark energy properties from galaxy clusters observed with LSST. This work focused on effects that could produce a systematic error on the measurement of cluster masses (that will be used to probe the effects of dark energy on the growth of structure). These effects stem from the deviations from pure ellipticity of the gravitational lensing signal and from the blending of lightmore » of neighboring galaxies. Both these effects are expected to be more significant for LSST than for the stage III experiments such as the Dark Energy Survey. We calculate the magnitude of the mass error (or bias) for the first time and demonstrate that it can be treated as a multiplicative correction and calibrated out, allowing mass measurements of clusters from gravitational lensing to meet the requirements of LSST's dark energy investigation.« less

Final Technical Report on the Institute for Advanced Study in Student Personnel Work.

ERIC Educational Resources Information Center

Callis, Robert

This document reports the planning, implementation, and evaluation of a 9-month institute held at the University of Missouri-Columbia to prepare participants (approximately 20) for leadership positions in student personnel work at junior colleges and technical institutes. The following aspects of the instructional program are discussed and…

O*NET Final Technical Report. Volume I [and] Volume II [and] Volume III.

ERIC Educational Resources Information Center

Peterson, Norman G.; Mumford, Michael D.; Borman, Walter C.; Jeanneret, P. Richard; Fleishman, Edwin A.; Levin, Kerry Y.

This document contains the three volumes of the technical report for development of the prototype of the Occupational Information Network (O*NET), which is intended to replace the "Dictionary of Occupational Titles.""General Introduction" (Norman G. Peterson) presents an overview of O*NET's purpose, content, and structure.…

Exascale Virtualized and Programmable Distributed Cyber Resource Control: Final Scientific Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yoo, S.J.Ben; Lauer, Gregory S.

large file transfers within a single domain. Adding support for IP traffic changes the nature of the RSA problem: instead of choosing to accept or deny each request for network support, IP traffic is inherently elastic and thus lends itself to a bandwidth maximization formulation. We developed a number of algorithms that could be easily deployed within existing and new FlexGrid networks, leading to networks that better support scientific collaboration. Cross-domain RSA research is essential to support large-scale FlexGrid networks, since configuration information is generally not shared or coordinated across domains. The results presented here are in their early stages. They are technically feasible and practical, but still require coordination among organizations and equipment owners and a higher-layer framework for managing network requests.« less

Theory of superconductivity in oxides. Final technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, P.W.

1988-05-18

Progress was made towards a final theory of high-Tc superconductivity. The key elements are the work on normal-state properties and the actual mechanism for Tc. With the understanding (ZA) of the large anisotropy and other transport properties in the normal state, the model is uniquely determined: one must have one version or another of a holon-spinon quantum-fluid state, which is not a normal Fermi liquid. And with the recognition (HWA) of the large-repulsion holon-holon interactions, the author has the first way of thinking quantitatively about the superconducting state. Work on the pure Heisenberg system, which is related but not necessarilymore » crucial to understanding the superconducting properties is described.« less

Robot-assisted intraocular surgery: development of the IRISS and feasibility studies in an animal model

PubMed Central

Rahimy, E; Wilson, J; Tsao, T-C; Schwartz, S; Hubschman, J-P

2013-01-01

Purpose The aim of this study is to develop a novel robotic surgical platform, the IRISS (Intraocular Robotic Interventional and Surgical System), capable of performing both anterior and posterior segment intraocular surgery, and assess its performance in terms of range of motion, speed of motion, accuracy, and overall capacities. Patients and methods To test the feasibility of performing ‘bimanual' intraocular surgical tasks using the IRISS, we defined four steps out of typical anterior (phacoemulsification) and posterior (pars plana vitrectomy (PPV)) segment surgery. Selected phacoemulsification steps included construction of a continuous curvilinear capsulorhexis and cortex removal in infusion–aspiration (I/A) mode. Vitrectomy steps consisted of performing a core PPV, followed by aspiration of the posterior hyaloid with the vitreous cutter to induce a posterior vitreous detachment (PVD) assisted with triamcinolone, and simulation of the microcannulation of a temporal retinal vein. For each evaluation, the duration and the successful completion of the task with or without complications or involuntary events was assessed. Results Intraocular procedures were successfully performed on 16 porcine eyes. Four eyes underwent creation of a round, curvilinear anterior capsulorhexis without radialization. Four eyes had I/A of lens cortical material completed without posterior capsular tear. Four eyes completed 23-gauge PPV followed by successful PVD induction without any complications. Finally, simulation of microcannulation of a temporal retinal vein was successfully achieved in four eyes without any retinal tears/perforations noted. Conclusion Robotic-assisted intraocular surgery with the IRISS may be technically feasible in humans. Further studies are pending to improve this particular surgical platform. PMID:23722720

Cogeneration feasibility: Otis Elevator Company and Polychrome Corporation. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1982-05-01

The purpose of this study was to assess the feasibility of cogeneration at Otis Elevator Company and Polychrome Corporation located in Westchester County, New York. Each plant and its associated thermal and electrical load is reviewed. Three basic cycles for the cogeneration are investigated: power only, power generation with waste heat recovery, and combined cycle. Each case was assessed economically, beginning with a screening method to suggest those configurations most likely to be implemented and continuing through an assessment of the regulatory environment for cogeneration and an analysis of rate structures for buy back power, displaced power, and supplementing service.more » It is concluded that: for a plant designed to supply the combined loads of the two corporations, interconnection costs coupled to the coincidence of load result in unfavorable economics; for separate cogeneration plants, owned and operated by each individual corporation, energy consumption patterns and the current regulatory environment, in particular the existing and proposed cogeneration system rate structures, do not permit viable economics for the proposed plants; but if the proposed cycle were owned and operated by a new entity (neither Otis/Polychrome nor the utility), an economic scheme with marginal financial benefits can be developed and may be worthy of further study. (LEW)« less

CEEM Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowers, John

for concentrating photovoltaic applications thathave substantially higher efficiency than single substrate cells made of elemental semiconductors such as silicon. This task required the development of new cell bonding methods with excellent coupling of both photons and electrons between the sub-cells. To accomplish this, we developed (1) GaInN solar cells with enhanced performance by using quantum-well absorbers and front-surface optical texturing, (2) a hybrid "pillar-array" bond which uses an array of metal pillars for electrical coupling, and (3) a "hybrid moth-eye" optical coating which combines the benefits of nano-imprinted moth-eye coatings and traditional multilayer coatings. The technical effectiveness was assessed by measurement of the photovoltaic efficiency of solar cells made using these techniques; the ultrahigh efficiencies targeted by this work are of compelling economic value for concentrating photovoltaics.« less

Beyond xMOOCs in healthcare education: study of the feasibility in integrating virtual patient systems and MOOC platforms.

PubMed

Stathakarou, Natalia; Zary, Nabil; Kononowicz, Andrzej A

2014-01-01

Background. Massive Open Online Courses (MOOCs) are an emerging trend in online learning. However, their technology is not yet completely adjusted to the needs of healthcare education. Integration of Virtual Patients within MOOCs to increase interactivity and foster clinical reasoning skills training, has been discussed in the past, but not verified by a practical implementation. Objective. To investigate the technical feasibility of integrating MOOCs with Virtual Patients for the purpose of enabling further research into the potential pedagogical benefits of this approach. Methods. We selected OpenEdx and Open Labyrinth as representative constituents of a MOOC platform and Virtual Patient system integration. Based upon our prior experience we selected the most fundamental technical requirement to address. Grounded in the available literature we identified an e-learning standard to guide the integration. We attempted to demonstrate the feasibility of the integration by designing a "proof-of-concept" prototype. The resulting pilot implementation was subject of verification by two test cases. Results. A Single Sign-On mechanism connecting Open Labyrinth with OpenEdx and based on the IMS LTI standard was successfully implemented and verified. Conclusion. We investigated the technical perspective of integrating Virtual Patients with MOOCs. By addressing this crucial technical requirement we set a base for future research on the educational benefits of using virtual patients in MOOCs. This provides new opportunities for integrating specialized software in healthcare education at massive scale.

Beyond xMOOCs in healthcare education: study of the feasibility in integrating virtual patient systems and MOOC platforms

PubMed Central

Zary, Nabil; Kononowicz, Andrzej A.

2014-01-01

Background. Massive Open Online Courses (MOOCs) are an emerging trend in online learning. However, their technology is not yet completely adjusted to the needs of healthcare education. Integration of Virtual Patients within MOOCs to increase interactivity and foster clinical reasoning skills training, has been discussed in the past, but not verified by a practical implementation. Objective. To investigate the technical feasibility of integrating MOOCs with Virtual Patients for the purpose of enabling further research into the potential pedagogical benefits of this approach. Methods. We selected OpenEdx and Open Labyrinth as representative constituents of a MOOC platform and Virtual Patient system integration. Based upon our prior experience we selected the most fundamental technical requirement to address. Grounded in the available literature we identified an e-learning standard to guide the integration. We attempted to demonstrate the feasibility of the integration by designing a “proof-of-concept” prototype. The resulting pilot implementation was subject of verification by two test cases. Results. A Single Sign-On mechanism connecting Open Labyrinth with OpenEdx and based on the IMS LTI standard was successfully implemented and verified. Conclusion. We investigated the technical perspective of integrating Virtual Patients with MOOCs. By addressing this crucial technical requirement we set a base for future research on the educational benefits of using virtual patients in MOOCs. This provides new opportunities for integrating specialized software in healthcare education at massive scale. PMID:25405078

7 CFR 1944.419 - Final grantee evaluation.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) PROGRAM REGULATIONS (CONTINUED) HOUSING Self-Help Technical Assistance Grants § 1944.419 Final grantee... Agriculture Regulations of the Department of Agriculture (Continued) RURAL HOUSING SERVICE, RURAL BUSINESS..., application, this regulation, and any amendments. (a) This is a quantitative evaluation of the grantee to...

Transcardiac endograft delivery for endovascular treatment of the ascending aorta: a feasibility study in pigs.

PubMed

Wipper, Sabine; Lohrenz, Christina; Ahlbrecht, Oliver; Carpenter, Sebastian W; Tsilimparis, Nikolaos; Kersten, Jan Felix; Detter, Christian; Debus, Eike S; Kölbel, Tilo

2015-06-01

To compare the technical feasibility and hemodynamic alterations during antegrade transcardiac access routes vs conventional transfemoral access (TFA) for endovascular treatment of the ascending aorta in a porcine model. Antegrade transseptal access (TSA), transapical access (TAA), and TFA were used for implantation of custom-made endografts into the ascending aorta under fluoroscopy (6 pigs each). Hemodynamic parameters, myocardial and cerebral blood flow, and carotid artery blood flow were evaluated during baseline (T1), sheath advancement (T2), after sheath retraction (T3), and after endograft deployment (T4). Endograft deployment was feasible in all animals; all coronary arteries remained patent. Hemodynamic parameters were comparable in all 3 study groups during all measurements. During T2, transient hemodynamic alteration occurred in all groups, with transient severe valve insufficiency in TSA and TAA reflected by the higher pulmonary to mean arterial pressure ratio (p<0.05) as compared with TFA. Values stabilized again at T3 and remained stable until T4. The innominate artery was partially occluded in 4 (TSA), 3 (TAA), and 5 (TFA) animals. There was no deterioration of myocardial or cerebral perfusion during the procedures. Endograft deployment and fluoroscopy times during TAA were shorter than in TSA and TFA. TSA, TFA, and TAA to the ascending aorta are feasible for endograft delivery to the ascending aorta in a porcine model. Transient hemodynamic instability in TSA and TAA recovered to near preoperative values. TAA appeared technically easier. © The Author(s) 2015.

Feasibility Study for an Autonomous UAV -Magnetometer System -- Final Report on SERDP SEED 1509:2206

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roelof Versteeg; Mark McKay; Matt Anderson

2007-09-01

Large areas across the United States are potentially contaminated with UXO, with some ranges encompassing tens to hundreds of thousands of acres. Technologies are needed which will allow for cost effective wide area scanning with 1) near 100 % coverage and 2) near 100 % detection of subsurface ordnance or features indicative of subsurface ordnance. The current approach to wide area scanning is a multi-level one, in which medium altitude fixed wing optical imaging is used for an initial site assessment. This assessment is followed with low altitude manned helicopter based magnetometry followed by surface investigations using either towed geophysicalmore » sensor arrays or man portable sensors. In order to be effective for small UXO detection, the sensing altitude for magnetic site investigations needs to be on the order of 1 – 3 meters. These altitude requirements means that manned helicopter surveys will generally only be feasible in large, open and relatively flat terrains. While such surveys are effective in mapping large areas relatively fast there are substantial mobilization/demobilization, staffing and equipment costs associated with these surveys (resulting in costs of approximately $100-$150/acre). Surface towed arrays provide high resolution maps but have other limitations, e.g. in their ability to navigate rough terrain effectively. Thus, other systems are needed allowing for effective data collection. An UAV (Unmanned Aerial Vehicle) magnetometer platform is an obvious alternative. The motivation behind such a system is that it would be safer for the operators, cheaper in initial and O&M costs, and more effective in terms of site characterization. However, while UAV data acquisition from fixed wing platforms for large (> 200 feet) stand off distances is relatively straight forward, a host of challenges exist for low stand-off distance (~ 6 feet) UAV geophysical data acquisition. The objective of SERDP SEED 1509:2006 was to identify the primary

Treatment of urban river contaminated sediment with ex situ advanced oxidation processes: technical feasibility, environmental discharges and cost-performance analysis.

PubMed

Yan, Dickson Y S; Liu, Tongzhou; Lo, Irene M C

2015-01-01

The technical feasibility, environmental discharges and cost-performance of urban river contaminated sediment treatment with ex situ advanced oxidation processes were evaluated for the purpose of achieving an ideal treatment goal (for marine disposal) and a cost-performance treatment goal (for beneficially reusing as a filling material). Sediment samples were collected from a river located in southern China. To achieve the ideal treatment goal, sequential treatments (Fenton's reaction+activated persulphate oxidation) were carried out. One-step Fenton's reaction was applied to achieve the cost-performance treatment goal. The resulting effluent was treated and discharged, and sludge generated in wastewater treatment was characterized. The resources input throughout the treatment processes were recorded for cost estimation. After the treatment designed for achieving the ideal treatment goal, most pollutants fulfilled the treatment goal except Pb, Cd, Hg and Ag, probably because these four metals were present mainly in stable fractions of the sediment. The cost-performance treatment goal was achieved in view of low pollutant contents in the toxicity characteristic leaching procedure leachate of treated sediment. The cost for achieving the cost-performance treatment goal is much less than that for achieving the ideal treatment goal. The major cost difference is attributed to chemical cost. Stringent sediment treatment goals based on existing standards would lead to massive chemical use, complex treatment and hence huge cost. A simpler treatment with fewer chemicals is adequate for sediment beneficially reused as a filling material, and is economically more advantageous than handling sediment for marine disposal.

Technical parameters for specifying imagery requirements

NASA Technical Reports Server (NTRS)

Coan, Paul P.; Dunnette, Sheri J.

1994-01-01

Providing visual information acquired from remote events to various operators, researchers, and practitioners has become progressively more important as the application of special skills in alien or hazardous situations increases. To provide an understanding of the technical parameters required to specify imagery, we have identified, defined, and discussed seven salient characteristics of images: spatial resolution, linearity, luminance resolution, spectral discrimination, temporal discrimination, edge definition, and signal-to-noise ratio. We then describe a generalizing imaging system and identified how various parts of the system affect the image data. To emphasize the different applications of imagery, we have constrasted the common television system with the significant parameters of a televisual imaging system for technical applications. Finally, we have established a method by which the required visual information can be specified by describing certain technical parameters which are directly related to the information content of the imagery. This method requires the user to complete a form listing all pertinent data requirements for the imagery.

Texas Hydrogen Education Final Scientific/Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hitchcock, David; Bullock, Dan

2011-06-30

fork lifts, and hydrogen fueling) are effective for engaging target audiences, and (3) a clear path forward is needed for state and local agencies interested in project implementation (funding, financing, preliminary design, technical assistance, etc.).« less

Comparison and Contrast of the Elimination Campaigns for Poliomyelitis and Leprosy: Which is More Feasible?

PubMed

Malheiro, Luís; Pinto, Sofia Correia; Sarmento, Antonio; Santos, Lurdes

2016-04-01

As we approach the third decade since the WHO started addressing the eradication of poliomyelitis and leprosy, a reflection of the previous campaigns efficacy and an evaluation of further elimination feasibility is important to adapt and intensify the next steps. We performed a critical review of the poliomyelitis and leprosy eradication campaigns to evaluate their technical and operational feasibilities. Vaccination and active case search are highly effective tools against poliomyelitis. If political stability and good vaccination coverage is achieved, poliomyelitis will be an easy target for eradication. Leprosy, on the other hand, faces many barriers towards elimination. The lack of a high efficacy vaccine, the long asymptomatic but infective period, the lack of screening tests and a poorly established elimination target, prevents this disease from being eliminated. In a world where resources and funding are limited, it is apparent that poliomyelitis is a more feasible target for elimination than leprosy.

Indexing NASA programs for technology transfer methods development and feasibility

NASA Technical Reports Server (NTRS)

Clingman, W. H.

1972-01-01

This project was undertaken to evaluate the application of a previously developed indexing methodology to ongoing NASA programs. These programs are comprehended by the NASA Program Approval Documents (PADS). Each PAD contains a technical plan for the area it covers. It was proposed that these could be used to generate an index to the complete NASA program. To test this hypothesis two PADS were selected by the NASA Technology Utilization Office for trial indexing. Twenty-five individuals indexed the two PADS using NASA Thesaurus terms. The results demonstrated the feasibility of indexing ongoing NASA programs using PADS as the source of information. The same indexing methodology could be applied to other documents containing a brief description of the technical plan. Results of this project showed that over 85% of the concepts in the technology should be covered by the indexing. Also over 85% of the descriptors chosen would be accurate. This completeness and accuracy for the indexing is considered satisfactory for application in technology transfer.

Seattle To Portland Inter-City ITS Corridor Study And Communications Plan, Final Report

DOT National Transportation Integrated Search

1996-03-01

THIS DOCUMENT IS THE FINAL REPORT PRESENTING THE SEATTLE TO PORTLAND INTELLIGENT TRANSPORTATION SYSTEM (ITS) EARLY DEPLOYMENT PLAN. THE FINAL REPORT SYNTHESIZES INFORMATION FROM TECHNICAL MEMORANDUMS 1 THROUGH 5; INCLUDING EXISTING AND FUTURE CONDITI...

Data-driven planning of distributed energy resources amidst socio-technical complexities

NASA Astrophysics Data System (ADS)

Jain, Rishee K.; Qin, Junjie; Rajagopal, Ram

2017-08-01

New distributed energy resources (DER) are rapidly replacing centralized power generation due to their environmental, economic and resiliency benefits. Previous analyses of DER systems have been limited in their ability to account for socio-technical complexities, such as intermittent supply, heterogeneous demand and balance-of-system cost dynamics. Here we develop ReMatch, an interdisciplinary modelling framework, spanning engineering, consumer behaviour and data science, and apply it to 10,000 consumers in California, USA. Our results show that deploying DER would yield nearly a 50% reduction in the levelized cost of electricity (LCOE) over the status quo even after accounting for socio-technical complexities. We abstract a detailed matching of consumers to DER infrastructure from our results and discuss how this matching can facilitate the development of smart and targeted renewable energy policies, programmes and incentives. Our findings point to the large-scale economic and technical feasibility of DER and underscore the pertinent role DER can play in achieving sustainable energy goals.

SIAM Conference on Geometric Design and Computing. Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2002-03-11

The SIAM Conference on Geometric Design and Computing attracted 164 domestic and international researchers, from academia, industry, and government. It provided a stimulating forum in which to learn about the latest developments, to discuss exciting new research directions, and to forge stronger ties between theory and applications. Final Report

An Investigation Into the Feasibility of Merging Three Technical Processing Operations Into One Central Unit.

ERIC Educational Resources Information Center

Burns, Robert W., Jr.

Three contiguous schools in the upper midwest--a teacher's training college and a private four-year college in one state, and a land-grant university in another--were studied to see if their libraries could merge one of their major divisions--technical services--into a single administrative unit. Potential benefits from such a merger were felt to…

77 FR 8095 - Technical Corrections to Commission Regulations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-14

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission 18 CFR Part 2 [Docket No. RM11-30-000; Order No. 756] Technical Corrections to Commission Regulations Issued February 8, 2012. AGENCY: Federal Energy Regulatory Commission, DOE. ACTION: Final rule: correcting amendment. SUMMARY: This document adds...

East End transportation study final report September 17, 2009

DOT National Transportation Integrated Search

2009-09-17

This report is the final component of a multi-year transit feasibility study conducted by the Volpe National Transportation Systems Center on behalf fo the five Towns of the East End. The initial transit conceptunder evaluation, a proposed Coordinate...

48 CFR 1852.235-73 - Final Scientific and Technical Reports.

Code of Federal Regulations, 2012 CFR

2012-10-01

... regarding appropriate electronic formats for final reports is available at http://www.sti.nasa.gov under....nasa.gov under the “Get Help” link. (e) In accordance with paragraph (d) of the Rights in Data—General... contained in NPR 2200.2, Guidelines for Documentation, Approval, and Dissemination of NASA Scientific and...

48 CFR 1852.235-73 - Final Scientific and Technical Reports.

Code of Federal Regulations, 2013 CFR

2013-10-01

... regarding appropriate electronic formats for final reports is available at http://www.sti.nasa.gov under....nasa.gov under the “Get Help” link. (e) In accordance with paragraph (d) of the Rights in Data—General... contained in NPR 2200.2, Guidelines for Documentation, Approval, and Dissemination of NASA Scientific and...

48 CFR 1852.235-73 - Final Scientific and Technical Reports.

Code of Federal Regulations, 2011 CFR

2011-10-01

... regarding appropriate electronic formats for final reports is available at http://www.sti.nasa.gov under....nasa.gov under the “Get Help” link. (e) In accordance with paragraph (d) of the Rights in Data—General... contained in NPR 2200.2, Guidelines for Documentation, Approval, and Dissemination of NASA Scientific and...

48 CFR 1852.235-73 - Final Scientific and Technical Reports.

Code of Federal Regulations, 2014 CFR

2014-10-01

... regarding appropriate electronic formats for final reports is available at http://www.sti.nasa.gov under....nasa.gov under the “Get Help” link. (e) In accordance with paragraph (d) of the Rights in Data—General... contained in NPR 2200.2, Guidelines for Documentation, Approval, and Dissemination of NASA Scientific and...

Technical Support and Documentation Management for 25 Ton All Terrain Crane (ATEC).

DTIC Science & Technology

1991-03-11

Rationale Report * Market Investigation and Supplement " Technical Feasibility Test Having considered material contained in the above documents and...Operational issues will be evaluated by OTEC as observers to the qualification testing . A logistics demonstration will be conducted in parallel with PPQT...Organizational OSHA Occupational Safety and Health Administration D-1 APPENDIX D - LIST OF ACRONYMNS (Continued) OTEC Operational Test and Evaluation Command OTP

Haiti: Feasibility of Waste-to-Energy Options at the Trutier Waste Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Conrad, M. D.; Hunsberger, R.; Ness, J. E.

2014-08-01

This report provides further analysis of the feasibility of a waste-to-energy (WTE) facility in the area near Port-au-Prince, Haiti. NREL's previous analysis and reports identified anaerobic digestion (AD) as the optimal WTE technology at the facility. Building on the prior analyses, this report evaluates the conceptual financial and technical viability of implementing a combined waste management and electrical power production strategy by constructing a WTE facility at the existing Trutier waste site north of Port-au-Prince.

76 FR 11327 - Technical Amendments to Rule 17a-8: Financial Recordkeeping and Reporting of Currency and Foreign...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-02

... SECURITIES AND EXCHANGE COMMISSION 17 CFR Part 240 [Release No. 34-63949] Technical Amendments to...: Securities and Exchange Commission. ACTION: Final rule; technical amendments. SUMMARY: The Securities and Exchange Commission (``Commission'') is adopting technical amendments to Rule 17a-8 under the Securities...

Vulnerabilities in GSM technology and feasibility of selected attacks

NASA Astrophysics Data System (ADS)

Voznak, M.; Prokes, M.; Sevcik, L.; Frnda, J.; Toral-Cruz, Homer; Jakovlev, Sergej; Fazio, Peppino; Mehic, M.; Mikulec, M.

2015-05-01

Global System for Mobile communication (GSM) is the most widespread technology for mobile communications in the world and serving over 7 billion users. Since first publication of system documentation there has been notified a potential safety problem's occurrence. Selected types of attacks, based on the analysis of the technical feasibility and the degree of risk of these weaknesses, were implemented and demonstrated in laboratory of the VSB-Technical University of Ostrava, Czech Republic. These vulnerabilities were analyzed and afterwards possible attacks were described. These attacks were implemented using open-source tools, software programmable radio USRP (Universal Software RadioPeripheral) and DVB-T (Digital Video Broadcasting - Terrestrial) receiver. GSM security architecture is being scrutinized since first public releases of its specification mainly pointing out weaknesses in authentication and ciphering mechanisms. This contribution also summarizes practically proofed and used scenarios that are performed using opensource software tools and variety of scripts mostly written in Python. Main goal of this paper is in analyzing security issues in GSM network and practical demonstration of selected attacks.

Technical and Economic Assessment of the Implementation of Measures for Reducing Energy Losses in Distribution Systems

NASA Astrophysics Data System (ADS)

Aguila, Alexander; Wilson, Jorge

2017-07-01

This paper develops a methodology to assess a group of measures of electrical improvements in distribution systems, starting from the complementation of technical and economic criteria. In order to solve the problem of energy losses in distribution systems, technical and economic analysis was performed based on a mathematical model to establish a direct relationship between the energy saved by way of minimized losses and the costs of implementing the proposed measures. This paper aims at analysing the feasibility of reducing energy losses in distribution systems, by changing existing network conductors by larger crosssection conductors and distribution voltage change at higher levels. The impact of this methodology provides a highly efficient mathematical tool for analysing the feasibility of implementing improvement projects based on their costs which is a very useful tool for the distribution companies that will serve as a starting point to the analysis for this type of projects in distribution systems.

Solar 2 Green Energy, Arts & Education Center. Final Scientific/Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paquette, Jamie C; Collins, Christopher J

provided to assist with the ongoing design work of Solar 2, including architecture, engineering and the development of construction specifications. The work performed during the project period brought this process as far along as it could go pending the raising of funds to begin construction of the building. Once those funds are secured, we will finalize any additional details needed before beginning the bidding process and then moving into construction. DOE's funding was extremely valuable in helping Solar One determine the feasibility of a net-zero construction on the site and allowed for the design to project to meet the high standards necessary for LEED Platinum status.« less

National Data Program for the Marine Environment Technical Development Plan. Final Report, Volume Two.

ERIC Educational Resources Information Center

System Development Corp., Santa Monica, CA.

A national data program for the marine environment is recommended. Volume 2 includes: (1) objectives, scope, and methodology; (2) summary of the technical development plan; (3) agency development plans - Great Lakes and coastal development and (4) marine data network development plans. (Author)

Technical-tactical analysis of youth olympic taekwondo combat.

PubMed

Tornello, Francesco; Capranica, Laura; Minganti, Carlo; Chiodo, Salvatore; Condello, Giancarlo; Tessitore, Antonio

2014-04-01

The purpose of this study was to define the technical and tactical profiles of official youth taekwondo competitions played under the most recent rules of the International Taekwondo Federation. Tactical actions (i.e., attack, defense, and block), technical executions (from 1- to 4-point scores), kicking legs (i.e., front/rear and right/left), and overall technical effectiveness were investigated in relation to match outcome of semifinal and final competitions (n = 50) of youth (aged 13-14 years) black belt athletes during the Italian Taekwondo Cadet Championship. Differences (p < 0.001) were found among all action typologies (Attack: 50.9 ± 2.2%; Defense: 27.7 ± 1.5%; Block: 21.3 ± 1.6%), with winners showing fewer (p = 0.005) offensive actions and more (p = 0.001) defensive actions with respect to non-winners. Independently from match outcome, technical exchanges showed differences (p < 0.001) for technical executions. Winners resulted more efficient (p < 0.001) for both technical and tactical variables. In general, these findings showed that Cadets tend to adopt an offensive strategy. In considering that the adoption of the new electronic system requires athletes to execute correct technical actions to have a score assigned, coaches should emphasize the effectiveness of scoring techniques and help athletes to effectively improve their defense and counterattack capabilities.

Validation of Technical Recommendations. Final Report. ISSOE Managing Student Progress.

ERIC Educational Resources Information Center

Ridley, Dennis; And Others

This report is organized to provide a complete, logical presentation of the major steps taken in the third phase of research on dynamics of dissemination of the Instructional Support System for Occupational Education (ISSOE). It reports on the confirmation and validation of the Phase II Final Report on Dissemination Issues and the Phase III…

HOOPER BAY HOUSING ANALYSIS AND ENERGY FEASIBILITY REPORT

DOE Office of Scientific and Technical Information (OSTI.GOV)

SEA LION CORPORATION; COLD CLIMATE HOUSING RESEARCH CENTER; SOLUTIONS FOR HEALTHY BREATHING

2012-12-30

Sea Lion applied for and received a grant from the Department of Energy (DOE) towards this end titled Energy Efficiency Development and Deployment in Indian Country. The initial objectives of the Hooper Bay Energy Efficiency Feasibility Study were to demonstrate a 30% reduction in residential/commercial energy usage and identify the economic benefits of implementing energy efficiency measures to the Tribe through: (1) partnering with Whitney Construction and Solutions for Healthy Breathing in the training and hire of 2 local energy assessors to conduct energy audits of 9 representative housing models and 2 commercial units in the community. These homes aremore » representative of 52 homes constructed across different eras. (2) partnering with Cold Climate Housing Research Center to document current electrical and heating energy consumption and analyze data for a final feasibility report (3) assessing the economics of electricity & heating fuel usage; (4) projecting energy savings or fossil fuel reduction by modeling of improvement scenarios and cost feasibility The following two objectives will be completed after the publication of this report: (5) the development of materials lists for energy efficiency improvements (6) identifying financing options for the follow-up energy efficiency implementation phase.« less

Research in Information Processing and Computer Science. Final Technical Report.

ERIC Educational Resources Information Center

Carnegie-Mellon Univ., Pittsburgh, PA. Social Studies Curriculum Center.

This is the final scientific research report for the research in programing at Carnegie-Mellon University during 1968-1970. Three team programing efforts during the past two years have been the development of (1) BLISS--a system building language on the PDP-10 computer, (2) LC2--a conversational system on the IBM/360, and L*--a system building…

10 CFR 51.92 - Supplement to the final environmental impact statement.

Code of Federal Regulations, 2011 CFR

2011-01-01

... changes in the proposed action that are relevant to environmental concerns; or (2) There are new and..., technical, and other benefits and costs of the proposed action, to the extent that the final environmental... costs; (5) Include an analysis of other energy alternatives, to the extent that the final environmental...

The Feasibility of Generalized Acoustic Sensor Operator Training. Final Report for Period February 1974-February 1975.

ERIC Educational Resources Information Center

Daniels, Richard W.; Alden, David G.

The feasibility of generalized approaches to training military personnel in the use of different types of sonar/acoustic warfare systems was explored. The initial phase of the project consisted of the analysis of representative sonar and acoustic equipment to identify training areas and operator performance requirements that could be subjected to…

A feasibility study for conducting unattended night-time operations at WMKO

NASA Astrophysics Data System (ADS)

Stomski, Paul J.; Gajadhar, Sarah; Dahm, Scott; Jordan, Carolyn; Nordin, Tom

2016-08-01

In 2015, W. M. Keck Observatory conducted a study of the feasibility of conducting nighttime operations on Maunakea without any staff on the mountain. The study was motivated by the possibility of long term operational costs savings as well as other expected benefits. The goals of the study were to understand the technical feasibility and risk as well as to provide labor and cost estimates for implementation. The results of the study would be used to inform a decision about whether or not to fund and initiate a formal project aimed at the development of this new unattended nighttime operating capability. In this paper we will describe the study process as well as a brief summary of the results including the identified viable design alternative, the risk analysis, and the scope of work. We will also share the decisions made as a result of the study and current status of related follow-on activity.

Feasibility study concerning remediation and rehabilitation of industrial polluted lands on the Absheron Peninsula, Republic of Azerbaijan

NASA Astrophysics Data System (ADS)

Pivin, Majorie; Helsen, Stefan; Cuyvers, Lars

2014-05-01

wastes in the local area and industrial sites where a known risk (for health or ecosystems) is demonstrated. Various aspects are being considered to prioritize needed actions. The client will be informed on the existing remediation technologies and their applicability on the concerned lands, not only taking into account the pollution extent and local geology, but also the operation costs, and existing technical means of SOCAR and the country. With this knowledge as a starting point, ECOREM p.l.c. will strive to offer the most recent, innovative and customized solutions to advice SOCAR with the best available techniques for oil-contaminated land remediation and rehabilitation, in order to reduce the environmental externalities associated with the extraction activities. As a final aspect of this study, ECOREM will help SOCAR with the further development of their Strategic Action Plan for remediation and monitoring. Specific remediation measures will be defined in a realistic time schedule. Each and every stage of the proposed remediation technologies will be implemented in a realistic plan that needs to be technically and economically feasible for SOCAR.

A National Needs Assessment to Identify Technical Procedures in Vascular Surgery for Simulation Based Training.

PubMed

Nayahangan, L J; Konge, L; Schroeder, T V; Paltved, C; Lindorff-Larsen, K G; Nielsen, B U; Eiberg, J P

2017-04-01

Practical skills training in vascular surgery is facing challenges because of an increased number of endovascular procedures and fewer open procedures, as well as a move away from the traditional principle of "learning by doing." This change has established simulation as a cornerstone in providing trainees with the necessary skills and competences. However, the development of simulation based programs often evolves based on available resources and equipment, reflecting convenience rather than a systematic educational plan. The objective of the present study was to perform a national needs assessment to identify the technical procedures that should be integrated in a simulation based curriculum. A national needs assessment using a Delphi process was initiated by engaging 33 predefined key persons in vascular surgery. Round 1 was a brainstorming phase to identify technical procedures that vascular surgeons should learn. Round 2 was a survey that used a needs assessment formula to explore the frequency of procedures, the number of surgeons performing each procedure, risk and/or discomfort, and feasibility for simulation based training. Round 3 involved elimination and ranking of procedures. The response rate for round 1 was 70%, with 36 procedures identified. Round 2 had a 76% response rate and resulted in a preliminary prioritised list after exploring the need for simulation based training. Round 3 had an 85% response rate; 17 procedures were eliminated, resulting in a final prioritised list of 19 technical procedures. A national needs assessment using a standardised Delphi method identified a list of procedures that are highly suitable and may provide the basis for future simulation based training programs for vascular surgeons in training. Copyright © 2017 European Society for Vascular Surgery. Published by Elsevier Ltd. All rights reserved.

Final Technical Report. DeepCwind Consortium Research Program. January 15, 2010 - March 31, 2013

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dagher, Habib; Viselli, Anthony; Goupee, Andrew

This is the final technical report for the U.S. Department of Energy-funded program, DE-0002981: DeepCwind Consortium Research Program. The project objective was the partial validation of coupled models and optimization of materials for offshore wind structures. The United States has a great opportunity to harness an indigenous abundant renewable energy resource: offshore wind. In 2010, the National Renewable Energy Laboratory (NREL) estimated there to be over 4,000 GW of potential offshore wind energy found within 50 nautical miles of the US coastlines (Musial and Ram, 2010). The US Energy Information Administration reported the total annual US electric energy generation inmore » 2010 was 4,120 billion kilowatt-hours (equivalent to 470 GW) (US EIA, 2011), slightly more than 10% of the potential offshore wind resource. In addition, deep water offshore wind is the dominant US ocean energy resource available comprising 75% of the total assessed ocean energy resource as compared to wave and tidal resources (Musial, 2008). Through these assessments it is clear offshore wind can be a major contributor to US energy supplies. The caveat to capturing offshore wind along many parts of the US coast is deep water. Nearly 60%, or 2,450 GW, of the estimated US offshore wind resource is located in water depths of 60 m or more (Musial and Ram, 2010). At water depths over 60 m building fixed offshore wind turbine foundations, such as those found in Europe, is likely economically infeasible (Musial et al., 2006). Therefore floating wind turbine technology is seen as the best option for extracting a majority of the US offshore wind energy resource. Volume 1 - Test Site; Volume 2 - Coupled Models; and Volume 3 - Composite Materials« less

Feasibility Study of Solar Photovoltaics on Landfills in Puerto Rico (Second Study)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salasovich, J.; Mosey, G.

2011-08-01

This report presents the results of an assessment of the technical and economic feasibility of deploying a solar photovoltaics (PV) system on landfill sites in Puerto Rico. The purpose of this report is to assess the landfills with the highest potential for possible solar PV installation and estimate cost, performance, and site impacts of three different PV options: crystalline silicon (fixed tilt), crystalline silicon (single-axis tracking), and thin film (fixed tilt). The report outlines financing options that could assist in the implementation of a system. According to the site production calculations, the most cost-effective system in terms of return onmore » investment is the thin-film fixed-tilt technology. The report recommends financing options that could assist in the implementation of such a system. The landfills and sites considered in this report were all determined feasible areas in which to implement solar PV systems.« less

Transradial access for visceral endovascular interventions in morbidly obese patients: safety and feasibility.

PubMed

Biederman, Derek M; Marinelli, Brett; O'Connor, Paul J; Titano, Joseph J; Patel, Rahul S; Kim, Edward; Tabori, Nora E; Nowakowski, Francis S; Lookstein, Robert A; Fischman, Aaron M

2016-05-07

Transradial access (TRA) has been shown to lower morbidity and bleeding complications compared to transfemoral access in percutaneous coronary interventions. Morbid obesity, commonly defined as a body mass index (BMI) ≥40 kg/m2, has been shown to be a risk factor for access site complications irrespective of access site. This study evaluates the safety and feasibility of performing visceral endovascular interventions in morbidly obese patients via TRA. Procedural details, technical success, and 30-day major and minor access site, bleeding, and neurological adverse events were prospectively recorded in a database of 1057 procedures performed via the radial artery. From this database we identified 22 visceral interventions performed with TRA in 17 morbidly obese patients (age: 53 ± 11 years, female: 71%) with a median BMI of 42.7 kg/m2. Interventions included radio-embolization (n = 7, 31.8%), chemo-embolization (n = 6, 27.3%), uterine fibroid embolization (n = 4, 18.2%), renal embolization (n = 2, 9.1%), hepatic embolization (n = 1, 4.5%), lumbar artery embolization (n = 1, 4.5%), and renal angioplasty (n = 1, 4.5%). The technical success was 100%. There were no major or minor adverse access site, bleeding, or neurological complications at 30 days. This study suggests visceral endovascular interventions performed in morbidly obese patients are safe and feasible.

Safety and Feasibility of Transradial Access for Visceral Interventions in Patients with Thrombocytopenia.

PubMed

Titano, J J; Biederman, D M; Marinelli, B S; Patel, R S; Kim, E; Tabori, N E; Nowakowski, F S; Lookstein, R A; Fischman, A M

2016-05-01

Transradial access (TRA) has shown lower morbidity and decreased bleeding complications compared to transfemoral access. This study evaluates the safety and feasibility of TRA in thrombocytopenic patients undergoing visceral interventions. Patients who underwent visceral interventions via the radial artery with platelet count less than or equal to 50,000/µL were included in the study. Outcome variables included technical success, access site, bleeding, transfusion, and neurological complications. From July 1, 2012, to May 31, 2015, a total of 1353 peripheral interventions via TRA were performed, of which 85 procedures were performed in 64 patients (mean age 62.2 years) with a platelet count <50,000/µL (median 39,000/µL). Interventions included chemoembolization (n = 46), selective internal radiation therapy (n = 30), and visceral embolization (n = 9). Technical success was 97.6% with two cases of severe vessel spasm requiring ipsilateral femoral crossover. There was no major access site, bleeding, or neurological adverse events at 30 days. Minor access site hematomas occurred in five cases (5.9%) and were treated conservatively in all cases. Pre-procedural platelet transfusions were administered in 23 (27.1%) cases. There was no statistically significant difference in access site or bleeding complications between the transfused and nontransfused groups. Transradial visceral interventions in patients with thrombocytopenia are both feasible and safe, possibly without the need for platelet transfusions.

Evaluating Self-Funded Health Insurance for the Lakeshore Technical Institute as a Cost-Containment Measure.

ERIC Educational Resources Information Center

Holstein, Karen E.

In response to the rising costs of health care and large increases in insurance premiums, a study was conducted at Lakeshore Technical Institute (LTI) to investigate the feasibility of using a self-funded health insurance plan at the college. Data were obtained through a literature review; telephone and on-site discussions with a personnel…

How to Train an Injured Brain? A Pilot Feasibility Study of Home-Based Computerized Cognitive Training.

PubMed

Verhelst, Helena; Vander Linden, Catharine; Vingerhoets, Guy; Caeyenberghs, Karen

2017-02-01

Computerized cognitive training programs have previously shown to be effective in improving cognitive abilities in patients suffering from traumatic brain injury (TBI). These studies often focused on a single cognitive function or required expensive hardware, making it difficult to be used in a home-based environment. This pilot feasibility study aimed to evaluate the feasibility of a newly developed, home-based, computerized cognitive training program for adolescents who suffered from TBI. Additionally, feasibility of study design, procedures, and measurements were examined. Case series, longitudinal, pilot, feasibility intervention study with one baseline and two follow-up assessments. Nine feasibility outcome measures and criteria for success were defined, including accessibility, training motivation/user experience, technical smoothness, training compliance, participation willingness, participation rates, loss to follow-up, assessment timescale, and assessment procedures. Five adolescent patients (four boys, mean age = 16 years 7 months, standard deviation = 9 months) with moderate to severe TBI in the chronic stage were recruited and received 8 weeks of cognitive training with BrainGames. Effect sizes (Cohen's d) were calculated to determine possible training-related effects. The new cognitive training intervention, BrainGames, and study design and procedures proved to be feasible; all nine feasibility outcome criteria were met during this pilot feasibility study. Estimates of effect sizes showed small to very large effects on cognitive measures and questionnaires, which were retained after 6 months. Our pilot study shows that a longitudinal intervention study comprising our novel, computerized cognitive training program and two follow-up assessments is feasible in adolescents suffering from TBI in the chronic stage. Future studies with larger sample sizes will evaluate training-related effects on cognitive functions and underlying brain structures.

Housing Value Projection Model Related to Educational Planning: The Feasibility of a New Methodology. Final Report.

ERIC Educational Resources Information Center

Helbock, Richard W.; Marker, Gordon

This study concerns the feasibility of a Markov chain model for projecting housing values and racial mixes. Such projections could be used in planning the layout of school districts to achieve desired levels of socioeconomic heterogeneity. Based upon the concepts and assumptions underlying a Markov chain model, it is concluded that such a model is…

Wisconsin Elementary Teacher Education Project. Volume VI, Feasibility Study: Pricing and Economic Analysis Study. Final Report.

ERIC Educational Resources Information Center

Wisconsin Univ., Madison.

This document is the second volume of the feasibility study report for the Wisconsin Elementary Teacher Education Project. It provides in part 1 data on program, planning and budgeting, including cost figures for preparing students in the present and new programs, marginal expenses, and costs for implementing the program on other campuses. Part 2…

Eye-tracking computer systems for inpatients with tetraplegia: findings from a feasibility study.

PubMed

van Middendorp, J J; Watkins, F; Park, C; Landymore, H

2014-12-02

Study design:A longitudinal, prospective, self-controlled cohort study.Objectives:To determine (1) the preliminary benefits of using eye-tracking computer systems (ETCSs) among inpatients with tetraplegia and (2) the feasibility of carrying out a well-powered randomized controlled trial.Setting:Specialist Spinal Cord Injuries Centre, United Kingdom; 6 months during 2013-2014.Methods:Individuals with tetraplegia who were admitted to the center and enrolled in this study were trained and allowed to use the ETCS (Tobii Eyegaze C15 System) twice a week for a duration of 10 weeks. Standardized training modules were developed and offered to all study participants. Study feasibility indicators as well as the Appraisals of Disability: Primary and Secondary Scale, Hospital Anxiety and Depression Scale and the Assistive Technology Device Predisposition Assessment questionnaire scores were taken before and after study enrollment.Results:A total of 31 inpatients with tetraplegia were screened. Although 14 patients (45%) met the study eligibility criteria, 6 patients (19%) consented to be enrolled in the study. Three participants did not complete the planned training schedule because of medical, technical and logistic reasons. Although half of the participants agreed that the ETCS under study was easy to use, no substantial improvements were seen in terms of psychological outcomes, appraisals of disability or independence.Conclusions:The conduct of a controlled trial evaluating the benefits of using ETCSs among newly injured patients with tetraplegia comes with considerable feasibility challenges. Until substantial technical improvements of ETCSs have been implemented, future research should initially focus on those individuals with tetraplegia who are living in the community and who have expressed a need to enhance their computer access and communication skills.Spinal Cord advance online publication, 2 December 2014; doi:10.1038/sc.2014.219.

Vocational-Technical Education Interface with Ohio's High Technology Business and Industrial Sector. Final Report.

ERIC Educational Resources Information Center

McCormick, Robert W.

This study explored the relationship of vocational-technical educational institutions in Ohio with business and industry using high-technology applications. The study attempted to determine what high-technology applications will be adopted by Ohio's business and industry in the next 5 years, what experience the schools have had in working with…

National Institute of Statistical Sciences Data Confidentiality Technical Panel: Final Report. NCES 2011-608

ERIC Educational Resources Information Center

Karr, Alan

2011-01-01

NCES asked the National Institute of Statistical Sciences (NISS) to convene a technical panel of survey and policy experts to examine the NCES current and planned data dissemination strategies for confidential data with respect to: mandates and directives that NCES make data available; current and prospective technologies for protecting and…

A Technical, User and Cost Comparison Study of Microfiche Duplicate Film Material. Final Report.

ERIC Educational Resources Information Center

Prevel, James J.

A technical, user and cost comparison study was undertaken to provide the Educational Resources Information Clearinghouse (ERIC) staff with data on silver halide, diazo, and vesicular type films for microfiche duplication. This information will allow ERIC to determine if diazo and/or vesicular films should be considered in producing ERIC duplicate…

Feasibility study of a brine boiling machine by solar energy

NASA Astrophysics Data System (ADS)

Phayom, W.

2018-06-01

This study presented the technical and operational feasibility of brine boiling machine by using solar energy instead of firewood or husk for salt production. The solar salt brine boiling machine consisted of a boiling chamber with an enhanced thermal efficiency through use of a solar brine heater. The stainless steel solar salt brine boiling chamber had dimensions of 60 cm x 70 cm x 20 cm. The steel brine heater had dimensions of 70 cm x 80 cm x 20 cm. The tilt angle of both the boiling chamber and brine heater was 20 degrees from horizontal. The brine temperature in the reservoir tank was 42°C with a flow rate of 6.64 L/h discharging into the solar boiling machine. It was found that the thermal efficiency and overall efficiency of the solar salt brine boiling machine were 0.63 and 0.38, respectively at a solar irradiance of 787.6 W/m2. The results shows that the potential of using solar energy for salt production system is feasible.

2+2+2 Dissemination Project Final Report.

ERIC Educational Resources Information Center

Sloane, Diana; And Others

An overview is provided in this three-part final report of a project designed to disseminate information to assist California high schools, Regional Occupation Programs, and colleges in developing and strengthening 2+2+2 programs. Part I reviews the following project objectives: (1) hire a project coordinator and technical assistant; (2) develop a…

Feasibility of Coherent and Incoherent Backscatter Experiments from the AMPS Laboratory. Technical Section

NASA Technical Reports Server (NTRS)

Mozer, F. S.

1976-01-01

A computer program simulated the spectrum which resulted when a radar signal was transmitted into the ionosphere for a finite time and received for an equal finite interval. The spectrum derived from this signal is statistical in nature because the signal is scattered from the ionosphere, which is statistical in nature. Many estimates of any property of the ionosphere can be made. Their average value will approach the average property of the ionosphere which is being measured. Due to the statistical nature of the spectrum itself, the estimators will vary about this average. The square root of the variance about this average is called the standard deviation, an estimate of the error which exists in any particular radar measurement. In order to determine the feasibility of the space shuttle radar, the magnitude of these errors for measurements of physical interest must be understood.

Cathodic Protection Field Trials on Prestressed Concrete Components, Final Report

DOT National Transportation Integrated Search

1998-01-01

This is the final report in a study to demonstrate the feasibility of using cathodic protection (CP) on concrete bridge structures containing prestressed steel. The interim report, FHWA-RD-95-032, has more details on the installation of selected CP s...

Flora of the Fraser Experimental Forest, Colorado. Forest Service general technical report (Final)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Popovich, S.J.; Shepperd, W.D.; Reichert, D.W.

1993-08-01

The report lists 441 vascular plant taxa in 228 genera and 63 families encountered on the 9,300-ha Fraser Experimental Forest in central Colorado. Synonyms appearing in previous publications and other works pertaining to the Fraser Experimental Forest, as well as appropriate Colorado floras and less-technical field guides, are included. Plant communities and habitats are discussed, and a list of 54 lichens is also presented. A glossary of related terms is included.

Final Technical Report: Electromagnetic Pump Insulation Materials Development and Testing (PLM-DOC-0005-2465) Report # DOEGEHB00613

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krahn, John; Reed, Claude; Loewen, Eric

Final Technical Report: Electromagnetic Pump Insulation Materials Development and Testing (Report # DOEGEHB00613) summarizes the information gathered from the analysis of the 160 m3/min EM Pump insulation that was tested in 2000-2002 and additional evaluations of new resilient, engineered insulation system evaluated and tested at both GRC and ANL. This report provides information on Tasks 1 and 2 of the entire project. This report also provides information in three broad areas: Historical and current data; Conclusions based on test data; and Insulation specifications for use in EM Pumps. The research for Task 2 builds upon Task 1: Update EM Pumpmore » Databank, which is summarized within this report. Where research for Task 3 and 4 Next-Generation EM Pump Analysis Tools identified parameters or analysis model that benefits Task 2 research, those items are noted within this report. The important design variables for the manufacture and operation of an EM Pump that the insulation research can evaluate are: space constraints; voltage capability of insulation system; maximum flux density through iron; flow rate and outlet pressure; efficiency and manufacturability. The development summary of the Electromagnetic Pump Insulation Materials Development and Testing was completed to include: Historical and current data; Conclusions based on test data; and Insulation specifications for use in EM Pumps.« less

PVWatts Version 1 Technical Reference

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dobos, A. P.

2013-10-01

The NREL PVWatts(TM) calculator is a web application developed by the National Renewable Energy Laboratory (NREL) that estimates the electricity production of a grid-connected photovoltaic system based on a few simple inputs. PVWatts combines a number of sub-models to predict overall system performance, and makes several hidden assumptions about performance parameters. This technical reference details the individual sub-models, documents assumptions and hidden parameters, and explains the sequence of calculations that yield the final system performance estimation.

Feasibility of Space Disposal of Radioactive Nuclear Waste. 1: Executive Summary

NASA Technical Reports Server (NTRS)

1973-01-01

This NASA study, performed at the request of the AEC, concludes that transporting radioactive waste (primarily long-lived isotopes) into space is feasible. Tentative solutions are presented for technical problems involving safe packaging. Launch systems (existing and planned), trajectories, potential hazards, and various destinations were evaluated. Solar system escape is possible and would have the advantage of ultimate removal of the radioactive waste from man's environment. Transportation costs would be low (comparable to less than a 5 percent increase in the cost of electricity) even though more than 100 space shuttle launches per year would be required by the year 2000.

King County Metro Transit Hybrid Articulated Buses: Final Evaluation Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chandler, K.; Walkowicz, K.

2006-12-01

Final technical report compares and evaluates new diesel and diesel hybrid-electric articulated buses operated as part of the King County Metro Transit (KC Metro) fleet in Seattle, Washington. The evaluation lasted 12 months.

Connecting the person with dementia and family: a feasibility study of a telepresence robot

PubMed Central

2014-01-01

Background Maintenance of communication is important for people with dementia living in long-term care. The purpose of this study was to assess the feasibility of using “Giraff”, a telepresence robot to enhance engagement between family and a person with dementia living in long-term care. Methods A mixed-methods approach involving semi-structured interviews, call records and video observational data was used. Five people with dementia and their family member participated in a discussion via the Giraff robot for a minimum of six times over a six-week period. A feasibility framework was used to assess feasibility and included video analysis of emotional response and engagement. Results Twenty-six calls with an average duration of 23 mins took place. Residents showed a general state of positive emotions across the calls with a high level of engagement and a minimal level of negative emotions. Participants enjoyed the experience and families reported that the Giraff robot offered the opportunity to reduce social isolation. A number of software and hardware challenges were encountered. Conclusions Participants perceived this novel approach to engage families and people with dementia as a feasible option. Participants were observed and also reported to enjoy the experience. The technical challenges identified have been improved in a newer version of the robot. Future research should include a feasibility trial of longer duration, with a larger sample and a cost analysis. PMID:24456417

Feasibility studies for the Forward Spectrometer

NASA Astrophysics Data System (ADS)

Biernat, Jacek; P¯ANDA Collaboration

2015-04-01

The Forward Spectrometer designed for the P¯ANDA detector will consist of many different detector systems allowing for precise track reconstruction and particle identification. Feasibility studies for Forward Spectrometer done by means of specific reactions will be presented. In the first part of the paper, results of simulations focussing on rate estimates of the tracking stations based on straw tubes will be presented. Next, the importance of the Forward Tracker will be demonstrated through the reconstruction of the ψ(4040) → DD¯ decay. Finally, results from the analysis of the experimental data collected with a straw tube prototype designed and constructed at the Research Center in Juelich will be discussed.

Feasibility of Construction of the Continuously Operating Geodetic GPS Network of Sinaloa, Mexico

NASA Astrophysics Data System (ADS)

Vazquez, G. E.; Jacobo, C.

2011-12-01

geometric distribution appropriate to ensure the state coverage, so the radius of coverage is found in the 10 to 15 Km. station. Likewise INEGI recommends the implementation of GPS measurements a priori in the vertices where at the end of such measurements generate a report by station containing details of the conditions of visibility, the GPS equipment used, the methodology of measurement and field data processing mode and is intended to build the RGOCSIN. Based on the results of the final report for each one of the measures beforehand, it will be or not feasible to determine if it meets these specifications to be finally considered as part of the RGOCSIN. It should be noted that the selection of the potential places where is intended to carry out the study and analysis of feasibility for the construction of the RGOCSIN will be some of the weather stations of the Centro de Investigación en Alimentación y Desarrollo (CIAD) Culiacán (http://www.ciad.edu.mx/clima/pc.asp). These weather stations have some technical infrastructure which would be used in the future; In addition to providing meteorological information which will ensure success in the solution of scientific and technological problems in various sectors requiring our state.

Knowledge Boosting Curriculum for New Wind Industry Professionals Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marsh, Ruth H; Rogers, Anthony L

DNV Renewables (USA) Inc. (DNV KEMA) received a grant from the U.S. Department of Energy (DOE) to develop the curriculum for a series of short courses intended to address Topic Area 5 Workforce Development, one of the focus areas to achieve the goals outlined in 20% Wind by 2030: Increasing Wind Energy's Contribution to Electricity Supply. The aim of the curriculum development project was to provide material for instructors to use in a training program to help professionals transition into careers in wind energy. Under this grant DNV KEMA established a knowledge boosting program for the wind energy industry withmore » the following objectives: 1. Develop technical training curricula and teaching materials for six key topic areas that can be implemented in a flexible format by a knowledgeable instructor. The topic areas form a foundation that can be leveraged for subsequent, more detailed learning modules (not developed in this program). 2. Develop an implementation guidance document to accompany the curricula outlining key learning objectives, implementation methods, and guidance for utilizing the curricula. This curriculum is intended to provide experienced trainers course material that can be used to provide course participants with a basic background in wind energy and wind project development. The curriculum addresses all aspects of developing a wind project, that when implemented can be put to use immediately, making the participant an asset to U.S. wind industry employers. The curriculum is comprised of six short modules, together equivalent in level of content to a one-semester college-level course. The student who completes all six modules should be able to understand on a basic level what is required to develop a wind project, speak with a reasonable level of confidence about such topics as wind resource assessment, energy assessment, turbine technology and project economics, and contribute to the analysis and review of project information. The content

78 FR 34392 - Guidance for Industry and Food and Drug Administration Staff: Technical Considerations for Pen...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-07

...] Guidance for Industry and Food and Drug Administration Staff: Technical Considerations for Pen, Jet, and... availability of a final guidance document entitled ``Technical Considerations for Pen, Jet, and Related... developing information to support a marketing application for a pen, jet, or related injector device intended...

Substitution of Assisted Living Services by Assistive Technology - Experts Opinions and Technical Feasibility.

PubMed

Schwartze, Jonas; Prekazi, Arianit; Schrom, Harald; Marschollek, Michael

2017-01-01

Ambient assisted living (AAL) may support ageing in place but is primarily driven by technology. The aim of this work is, to identifying reasons to move into assisted living institutions, their range of service and possible substitutability. We did semi-structured interviews with five experts from assisted living institutions and used results to design and implement assistive technologies in an AAL environment using BASIS, a cross domain bus system for smart buildings. Reasons for moving to assisted living institutions are expected benefits for chronic health problems, safety, social isolation and carefree living. We implemented six application systems for inactivity monitoring, stove shutdown, air quality monitoring, medication and appointment reminders, detection of unwanted situations before leaving and optical ringing of the doorbell. Substitution of selected assisted living services is feasible and has potential to delay necessity to move into assisted living institution if complement social services are installed.

Technical Feasibility of SCONOx

EPA Pesticide Factsheets

This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

Proof of the Feasibility of Coherent and Incoherent Schemes for Pumping a Gamma-Ray Laser

DTIC Science & Technology

1988-07-01

DIP!; ilLE-CWPj AD-A 799 638 The University of Texas at DallasCenter for Quantlin, Electronics The Gamma-Ray Laser Project Quarterly Report April...AND INCOHERENT SCHEMES FOR PUMPING A GAMMA-RAY LASER Principal Investigator: Carl B. Collins The University of Texas at Dallas Center for Quantum...FEASIBILITY OF Quarterly Technical Progress COHERENT AND INCOHERENT SCHEMES /I/RR - 61WARA FOR PUMPING A GAMMA-RAY LASER 6.PERFORMINO ORG. REPORT NUMBER

JCCRER Project 2.3 -- Deterministic effects of occupational exposure to radiation. Phase 1: Feasibility study; Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Okladnikova, N.; Pesternikova, V.; Sumina, M.

1998-12-01

Phase 1 of Project 2.3, a short-term collaborative Feasibility Study, was funded for 12 months starting on 1 February 1996. The overall aim of the study was to determine the practical feasibility of using the dosimetric and clinical data on the MAYAK worker population to study the deterministic effects of exposure to external gamma radiation and to internal alpha radiation from inhaled plutonium. Phase 1 efforts were limited to the period of greatest worker exposure (1948--1954) and focused on collaboratively: assessing the comprehensiveness, availability, quality, and suitability of the Russian clinical and dosimetric data for the study of deterministic effects;more » creating an electronic data base containing complete clinical and dosimetric data on a small, representative sample of MAYAK workers; developing computer software for the testing of a currently used health risk model of hematopoietic effects; and familiarizing the US team with the Russian diagnostic criteria and techniques used in the identification of Chronic Radiation Sickness.« less

[Engineering a bone free flap for maxillofacial reconstruction: technical restrictions].

PubMed

Raoul, G; Myon, L; Chai, F; Blanchemain, N; Ferri, J

2011-09-01

Vascularisation is a key for success in bone tissue engineering. Creating a functional vascular network is an important concern so as to ensure vitality in regenerated tissues. Many strategies were developed to achieve this goal. One of these is cellular growth technique by perfusion bioreactor chamber. These new technical requirements came along with improved media and chamber receptacles: bioreactors (chapter 2). Some bone tissue engineering processes already have clinical applications but for volumes limited by the lack of vascularisation. Resorbable or non-resorbable membranes are an example. They are used separately or in association with bone grafts and they protect the graft during the revascularization process. Potentiated osseous regeneration uses molecular or cellular adjuvants (BMPs and autologous stem cells) to improve osseous healing. Significant improvements were made: integration of specific sequences, which may guide and enhance cells differentiation in scaffold; nano- or micro-patterned cell containing scaffolds. Finally, some authors consider the patient body as an ideal bioreactor to induce vascularisation in large volumes of grafted tissues. "Endocultivation", i.e., cellular culture inside the human body was proven to be feasible and safe. The properties of regenerated bone in the long run remain to be assessed. The objective to reach remains the engineering of an "in vitro" osseous free flap without morbidity. Copyright © 2011 Elsevier Masson SAS. All rights reserved.

Cardiopulmonary performance testing using a robotics-assisted tilt table: feasibility assessment in able-bodied subjects.

PubMed

Saengsuwan, J; Laubacher, M; Nef, T; Hunt, K J

2014-01-01

Robotics-assisted tilt table technology was introduced for early rehabilitation of neurological patients. It provides cyclical stepping movement and physiological loading of the legs. The aim of the present study was to assess the feasibility of this type of device for peak cardiopulmonary performance testing using able-bodied subjects. A robotics-assisted tilt table was augmented with force sensors in the thigh cuffs and a work rate estimation algorithm. A custom visual feedback system was employed to guide the subjects' work rate and to provide real time feedback of actual work rate. Feasibility assessment focused on: (i) implementation (technical feasibility), and (ii) responsiveness (was there a measurable, high-level cardiopulmonary reaction?). For responsiveness testing, each subject carried out an incremental exercise test to the limit of functional capacity with a work rate increment of 5 W/min in female subjects and 8 W/min in males. 11 able-bodied subjects were included (9 male, 2 female; age 29.6 ± 7.1 years: mean ± SD). Resting oxygen uptake (O_{2}) was 4.6 ± 0.7 mL/min/kg and O_{2}peak was 32.4 ± 5.1 mL/min/kg; this mean O_{2}peak was 81.1% of the predicted peak value for cycle ergometry. Peak heart rate (HRpeak) was 177.5 ± 9.7 beats/min; all subjects reached at least 85% of their predicted HRpeak value. Respiratory exchange ratio (RER) at O_{2}peak was 1.02 ± 0.07. Peak work rate) was 61.3 ± 15.1 W. All subjects reported a Borg CR10 value for exertion and leg fatigue of 7 or more. The robotics-assisted tilt table is deemed feasible for peak cardiopulmonary performance testing: the approach was found to be technically implementable and substantial cardiopulmonary responses were observed. Further testing in neurologically-impaired subjects is warranted.

Laminar flow control SPF/08 feasibility demonstration

NASA Astrophysics Data System (ADS)

Ecklund, R. C.; Williams, N. R.

1981-10-01

The feasibility of applying superplastic forming/diffusion bonding (SPF/DB) technology to laminar flow control (LFC) system concepts was demonstrated. Procedures were developed to produce smooth, flat titanium panels, using thin -0.016 inch sheets, meeting LFC surface smoothness requirements. Two large panels 28 x 28 inches were fabricated as final demonstration articles. The first was flat on the top and bottom sides demonstrating the capability of the tooling and the forming and diffusion bonding procedures to produce flat, defect free surfaces. The second panel was configurated for LFC porous panel treatment by forming channels with dimpled projections on the top side. The projections were machined away leaving holes extending into the panel. A perforated titanium sheet was adhesively bonded over this surface to complete the LFC demonstration panel. The final surface was considered flat enough to meet LFC requirements for a jet transport aircraft in cruising flight.

Cross-State Air Pollution Rule Update Allowance Allocation Final Rule TSD

EPA Pesticide Factsheets

This Technical Support Document (TSD) provides information that supports EPA’s determination of unit-level allocations for existing and new units under the final Cross-State Air Pollution Rule Update.

[The LESS (Laparo-endoscopic Single-Site) procedure in urology. Technical and clinical aspects].

PubMed

Neri, F; Cindolo, L; Gidaro, S; Schips, L

2010-01-01

Minimally invasive urology is rapidly advancing, and single-site laparoscopic surgery is being explored clinically. Such laparoscopic procedures are technically challenging and require an experienced laparoscopic surgeon due to the lack of port placement triangulation and instrument clashing. In the last years several surgeons all over the world have explored the feasibility and safety of LESS using several and different ports, approaches and devices. Hundreds of procedures have been described with overall favorable intraoperative and postoperative outcomes. Our experience consists of more than 30 procedures successfully completed for adrenal, kidney disease and varicocele. To date, LESS could be considered feasible and effective using currently available devices, however it is to be considered as an initial status technique requiring further confirmatory studies and advanced laparoscopic skills.

Making a Difference in the Lives of Infants and Toddlers and Their Families: The Impacts of Early Head Start. Volumes I-III: Final Technical Report [and] Appendixes [and] Local Contributions to Understanding the Programs and Their Impacts.

ERIC Educational Resources Information Center

Love, John M.; Kisker, Ellen Eliason; Ross, Christine M.; Schochet, Peter Z.; Brooks-Gunn, Jeanne; Paulsell, Diane; Boller, Kimberly; Constantine, Jill; Vogel, Cheri; Fuligni, Alison Sidle; Brady-Smith, Christy

Early Head Start was designed in 1994 as a 2-generation program to enhance children's development and health, strengthen family and community partnerships, and support the staff delivering new services to low-income families with pregnant women, infants, or toddlers. This document contains the final technical report, appendixes, and local…

Dual-Doppler Feasibility Study

NASA Technical Reports Server (NTRS)

Huddleston, Lisa L.

2012-01-01

When two or more Doppler weather radar systems are monitoring the same region, the Doppler velocities can be combined to form a three-dimensional (3-D) wind vector field thus providing for a more intuitive analysis of the wind field. A real-time display of the 3-D winds can assist forecasters in predicting the onset of convection and severe weather. The data can also be used to initialize local numerical weather prediction models. Two operational Doppler Radar systems are in the vicinity of Kennedy Space Center (KSC) and Cape Canaveral Air Force Station (CCAFS); these systems are operated by the 45th Space Wing (45 SW) and the National Weather Service Melbourne, Fla. (NWS MLB). Dual-Doppler applications were considered by the 45 SW in choosing the site for the new radar. Accordingly, the 45th Weather Squadron (45 WS), NWS MLB and the National Aeronautics and Space Administration tasked the Applied Meteorology Unit (AMU) to investigate the feasibility of establishing dual-Doppler capability using the two existing systems. This study investigated technical, hardware, and software requirements necessary to enable the establishment of a dual-Doppler capability. Review of the available literature pertaining to the dual-Doppler technique and consultation with experts revealed that the physical locations and resulting beam crossing angles of the 45 SW and NWS MLB radars make them ideally suited for a dual-Doppler capability. The dual-Doppler equations were derived to facilitate complete understanding of dual-Doppler synthesis; to determine the technical information requirements; and to determine the components of wind velocity from the equation of continuity and radial velocity data collected by the two Doppler radars. Analysis confirmed the suitability of the existing systems to provide the desired capability. In addition, it is possible that both 45 SW radar data and Terminal Doppler Weather Radar data from Orlando International Airport could be used to alleviate any

The technical consideration of multi-beam mask writer for production

NASA Astrophysics Data System (ADS)

Lee, Sang Hee; Ahn, Byung-Sup; Choi, Jin; Shin, In Kyun; Tamamushi, Shuichi; Jeon, Chan-Uk

2016-10-01

Multi-beam mask writer is under development to solve the throughput and patterning resolution problems in VSB mask writer. Theoretically, the writing time is appropriate for future design node and the resolution is improved with multi-beam mask writer. Many previous studies show the feasible results of resolution, CD control and registration. Although such technical results of development tool seem to be enough for mass production, there are still many unexpected problems for real mass production. In this report, the technical challenges of multi-beam mask writer are discussed in terms of production and application. The problems and issues are defined based on the performance of current development tool compared with the requirements of mask quality. Using the simulation and experiment, we analyze the specific characteristics of electron beam in multi-beam mask writer scheme. Consequently, we suggest necessary specifications for mass production with multi-beam mask writer in the future.

Final Technical Report of the project "Controlling Quantum Information by Quantum Correlations"

DOE Office of Scientific and Technical Information (OSTI.GOV)

Girolami, Davide

The report describes hypotheses, aims, methods and results of the project 20170675PRD2, “Controlling Quantum Information by Quantum Correlations”, which has been run from July 31, 2017 to January 7, 2018. The technical work has been performed by Director’s Fellow Davide Girolami of the T-4 Division, Physics of Condensed Matter and Complex Systems, under the supervision of Wojciech Zurek (T-4), Lukasz Cincio (T-4), and Marcus Daniels (CCS-7). The project ended as Davide Girolami has been converted to J. R. Oppenheimer Fellow to work on the project 20180702PRD1, “Optimal Control of Quantum Machines”, started on January 8, 2018.

A Merger Feasibility Study: Greenville City and Pitt County (North Carolina) Schools. Final Report, 22N-2572.

ERIC Educational Resources Information Center

Pyecha, John N.; And Others

This report contains findings and recommendations based on a study conducted to determine the feasibility of merging the Pitt County and Greenville County (North Carolina) school systems. Each school system is described in terms of pupil population patterns, building use, and educational and administrative services; issues related to these…

Development, initial reliability and validity testing of an observational tool for assessing technical skills of operating room nurses.

PubMed

Sevdalis, Nick; Undre, Shabnam; Henry, Janet; Sydney, Elaine; Koutantji, Mary; Darzi, Ara; Vincent, Charles A

2009-09-01

The recent emergence of the Systems Approach to the safety and quality of surgical care has triggered individual and team skills training modules for surgeons and anaesthetists and relevant observational assessment tools have been developed. To develop an observational tool that captures operating room (OR) nurses' technical skill and can be used for assessment and training. The Imperial College Assessment of Technical Skills for Nurses (ICATS-N) assesses (i) gowning and gloving, (ii) setting up instrumentation, (iii) draping, and (iv) maintaining sterility. Three to five observable behaviours have been identified for each skill and are rated on 1-6 scales. Feasibility and aspects of reliability and validity were assessed in 20 simulation-based crisis management training modules for trainee nurses and doctors, carried out in a Simulated Operating Room. The tool was feasible to use in the context of simulation-based training. Satisfactory reliability (Cronbach alpha) was obtained across trainers' and trainees' scores (analysed jointly and separately). Moreover, trainer nurse's ratings of the four skills correlated positively, thus indicating adequate content validity. Trainer's and trainees' ratings did not correlate. Assessment of OR nurses' technical skill is becoming a training priority. The present evidence suggests that the ICATS-N could be considered for use as an assessment/training tool for junior OR nurses.

78 FR 13543 - Defense Federal Acquisition Regulation Supplement; Technical Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-28

... DEPARTMENT OF DEFENSE Defense Acquisition Regulations System 48 CFR Parts 201, 204, 215, 225, 227, 242, 245, and 252 Defense Federal Acquisition Regulation Supplement; Technical Amendments AGENCY: Defense Acquisition Regulations System, Department of Defense (DoD). ACTION: Final rule. SUMMARY: DoD is...