47 CFR 15.15 - General technical requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false General technical requirements. 15.15 Section 15.15 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES General § 15.15 General technical requirements. (a) An intentional or unintentional radiator shall be...

15 CFR 911.8 - Technical requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... PROCEDURES CONCERNING USE OF THE NOAA SPACE-BASED DATA COLLECTION SYSTEMS § 911.8 Technical requirements. (a) All platform operators of the NOAA DCS must use a data collection platform radio set whose technical...

15 CFR 911.8 - Technical requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... PROCEDURES CONCERNING USE OF THE NOAA SPACE-BASED DATA COLLECTION SYSTEMS § 911.8 Technical requirements. (a) All platform operators of the NOAA DCS must use a data collection platform radio set whose technical...

15 CFR 911.8 - Technical requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... PROCEDURES CONCERNING USE OF THE NOAA SPACE-BASED DATA COLLECTION SYSTEMS § 911.8 Technical requirements. (a) All platform operators of the NOAA DCS must use a data collection platform radio set whose technical...

15 CFR 911.8 - Technical requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... PROCEDURES CONCERNING USE OF THE NOAA SPACE-BASED DATA COLLECTION SYSTEMS § 911.8 Technical requirements. (a) All platform operators of the NOAA DCS must use a data collection platform radio set whose technical...

15 CFR 911.8 - Technical requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... PROCEDURES CONCERNING USE OF THE NOAA SPACE-BASED DATA COLLECTION SYSTEMS § 911.8 Technical requirements. (a) All platform operators of the NOAA DCS must use a data collection platform radio set whose technical...

Technical parameters for specifying imagery requirements

NASA Technical Reports Server (NTRS)

Coan, Paul P.; Dunnette, Sheri J.

1994-01-01

Providing visual information acquired from remote events to various operators, researchers, and practitioners has become progressively more important as the application of special skills in alien or hazardous situations increases. To provide an understanding of the technical parameters required to specify imagery, we have identified, defined, and discussed seven salient characteristics of images: spatial resolution, linearity, luminance resolution, spectral discrimination, temporal discrimination, edge definition, and signal-to-noise ratio. We then describe a generalizing imaging system and identified how various parts of the system affect the image data. To emphasize the different applications of imagery, we have constrasted the common television system with the significant parameters of a televisual imaging system for technical applications. Finally, we have established a method by which the required visual information can be specified by describing certain technical parameters which are directly related to the information content of the imagery. This method requires the user to complete a form listing all pertinent data requirements for the imagery.

40 CFR 58.11 - Network technical requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Network technical requirements. 58.11... (CONTINUED) AMBIENT AIR QUALITY SURVEILLANCE Monitoring Network § 58.11 Network technical requirements. (a)(1... A to this part when operating the SLAMS networks. (2) Beginning January 1, 2009, State and local...

40 CFR 58.11 - Network technical requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 5 2011-07-01 2011-07-01 false Network technical requirements. 58.11... (CONTINUED) AMBIENT AIR QUALITY SURVEILLANCE Monitoring Network § 58.11 Network technical requirements. (a)(1... A to this part when operating the SLAMS networks. (2) Beginning January 1, 2009, State and local...

Managing Information On Technical Requirements

NASA Technical Reports Server (NTRS)

Mauldin, Lemuel E., III; Hammond, Dana P.

1993-01-01

Technical Requirements Analysis and Control Systems/Initial Operating Capability (TRACS/IOC) computer program provides supplemental software tools for analysis, control, and interchange of project requirements so qualified project members have access to pertinent project information, even if in different locations. Enables users to analyze and control requirements, serves as focal point for project requirements, and integrates system supporting efficient and consistent operations. TRACS/IOC is HyperCard stack for use on Macintosh computers running HyperCard 1.2 or later and Oracle 1.2 or later.

Technical requirements for bioassay support services

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hickman, D.P.; Anderson, A.L.

1991-05-01

This document provides the technical basis for the Chem-Nuclear Geotech (Geotech) bioassay program. It includes information and details that can be used as a model in providing technical contents and requirements for bioassay laboratory support, either internally or in solicitations by Geotech to obtain subcontractor laboratory support. It provides a detailed summary and description of the types of bioassay samples to be expected in support of Geotech remedial projects for the US Department of Energy and the bioassay services and analytical requirements necessary to process such samples, including required limits of sensitivity. General responsibilities of the bioassay laboratory are alsomore » addressed, including quality assurance. Peripheral information of importance to the program is included in the appendices of this document. 7 tabs.« less

Relationship between intraoperative non-technical performance and technical events in bariatric surgery.

PubMed

Fecso, A B; Kuzulugil, S S; Babaoglu, C; Bener, A B; Grantcharov, T P

2018-03-30

The operating theatre is a unique environment with complex team interactions, where technical and non-technical performance affect patient outcomes. The correlation between technical and non-technical performance, however, remains underinvestigated. The purpose of this study was to explore these interactions in the operating theatre. A prospective single-centre observational study was conducted at a tertiary academic medical centre. One surgeon and three fellows participated as main operators. All patients who underwent a laparoscopic Roux-en-Y gastric bypass and had the procedures captured using the Operating Room Black Box ® platform were included. Technical assessment was performed using the Objective Structured Assessment of Technical Skills and Generic Error Rating Tool instruments. For non-technical assessment, the Non-Technical Skills for Surgeons (NOTSS) and Scrub Practitioners' List of Intraoperative Non-Technical Skills (SPLINTS) tools were used. Spearman rank-order correlation and N-gram statistics were conducted. Fifty-six patients were included in the study and 90 procedural steps (gastrojejunostomy and jejunojejunostomy) were analysed. There was a moderate to strong correlation between technical adverse events (r s  = 0·417-0·687), rectifications (r s  = 0·380-0·768) and non-technical performance of the surgical and nursing teams (NOTSS and SPLINTS). N-gram statistics showed that after technical errors, events and prior rectifications, the staff surgeon and the scrub nurse exhibited the most positive non-technical behaviours, irrespective of operator (staff surgeon or fellow). This study demonstrated that technical and non-technical performances are related, on both an individual and a team level. Valuable data can be obtained around intraoperative errors, events and rectifications. © 2018 BJS Society Ltd Published by John Wiley & Sons Ltd.

47 CFR 80.273 - Technical requirements for radar equipment.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 5 2011-10-01 2011-10-01 false Technical requirements for radar equipment. 80... Technical requirements for radar equipment. (a) Radar installations on board ships that are required by the Safety Convention or the U.S. Coast Guard to be equipped with radar must comply with the documents...

47 CFR 80.273 - Technical requirements for radar equipment.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Technical requirements for radar equipment. 80... Technical requirements for radar equipment. (a) Radar installations on board ships that are required by the Safety Convention or the U.S. Coast Guard to be equipped with radar must comply with the documents...

The Vehicle Integrated Performance Analysis Experience: Reconnecting With Technical Integration

NASA Technical Reports Server (NTRS)

McGhee, D. S.

2006-01-01

Very early in the Space Launch Initiative program, a small team of engineers at MSFC proposed a process for performing system-level assessments of a launch vehicle. Aimed primarily at providing insight and making NASA a smart buyer, the Vehicle Integrated Performance Analysis (VIPA) team was created. The difference between the VIPA effort and previous integration attempts is that VIPA a process using experienced people from various disciplines, which focuses them on a technically integrated assessment. The foundations of VIPA s process are described. The VIPA team also recognized the need to target early detailed analysis toward identifying significant systems issues. This process is driven by the T-model for technical integration. VIPA s approach to performing system-level technical integration is discussed in detail. The VIPA process significantly enhances the development and monitoring of realizable project requirements. VIPA s assessment validates the concept s stated performance, identifies significant issues either with the concept or the requirements, and then reintegrates these issues to determine impacts. This process is discussed along with a description of how it may be integrated into a program s insight and review process. The VIPA process has gained favor with both engineering and project organizations for being responsive and insightful

Analysis of the Parameters Required for Performance Monitoring and Assessment of Military Communications Systems by Military Technical Controller

DTIC Science & Technology

1975-12-01

139 APPENDIX A* BASIC CONCEPT OF MILITARY TECHNICAL CONTROL.142 6 APIENDIX Es TEST EQUIPMENI REQUIRED FOR lEASURF.4ENr OF 1AF’AMETE RS...Control ( SATEC ) Automatic Facilities heport Army Automated Quality Monitoring Reporting System (AQMPS) Army Autcmated Technical Control-Semi (ATC-Semi...technical control then beco.. es equipment status monitoring. All the major equipment in a system wculd have internal sensors with properly selected parameters

Career and Technical Education Administration: Requirements, Certification/Licensure, and Preparation

ERIC Educational Resources Information Center

Zirkle, Christopher J.; Jeffery, Jeremy O.

2017-01-01

The current climate of career and technical administration requirements in all 50 states was detailed and explored. An increasing number of states are not requiring specific career-technical administration certification/licensure in order to oversee secondary career and technical education (CTE) programs, with more states moving towards a general…

47 CFR 15.511 - Technical requirements for surveillance systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 1 2013-10-01 2013-10-01 false Technical requirements for surveillance systems... DEVICES Ultra-Wideband Operation § 15.511 Technical requirements for surveillance systems. (a) The UWB... surveillance systems operated by law enforcement, fire or emergency rescue organizations or by manufacturers...

47 CFR 15.511 - Technical requirements for surveillance systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 1 2012-10-01 2012-10-01 false Technical requirements for surveillance systems... DEVICES Ultra-Wideband Operation § 15.511 Technical requirements for surveillance systems. (a) The UWB... surveillance systems operated by law enforcement, fire or emergency rescue organizations or by manufacturers...

47 CFR 15.511 - Technical requirements for surveillance systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 1 2011-10-01 2011-10-01 false Technical requirements for surveillance systems... DEVICES Ultra-Wideband Operation § 15.511 Technical requirements for surveillance systems. (a) The UWB... surveillance systems operated by law enforcement, fire or emergency rescue organizations or by manufacturers...

47 CFR 15.511 - Technical requirements for surveillance systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Technical requirements for surveillance systems... DEVICES Ultra-Wideband Operation § 15.511 Technical requirements for surveillance systems. (a) The UWB... surveillance systems operated by law enforcement, fire or emergency rescue organizations or by manufacturers...

47 CFR 15.511 - Technical requirements for surveillance systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 1 2014-10-01 2014-10-01 false Technical requirements for surveillance systems... DEVICES Ultra-Wideband Operation § 15.511 Technical requirements for surveillance systems. (a) The UWB... surveillance systems operated by law enforcement, fire or emergency rescue organizations or by manufacturers...

Performance/Design Requirements and Detailed Technical Description for a Computer-Directed Training Subsystem for Integration into the Air Force Phase II Base Level System.

ERIC Educational Resources Information Center

Butler, A. K.; And Others

The performance/design requirements and a detailed technical description for a Computer-Directed Training Subsystem to be integrated into the Air Force Phase II Base Level System are described. The subsystem may be used for computer-assisted lesson construction and has presentation capability for on-the-job training for data automation, staff, and…

47 CFR 15.517 - Technical requirements for indoor UWB systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Technical requirements for indoor UWB systems. 15.517 Section 15.517 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES Ultra-Wideband Operation § 15.517 Technical requirements for indoor UWB systems. (a) Operation...

47 CFR 15.513 - Technical requirements for medical imaging systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Technical requirements for medical imaging systems. 15.513 Section 15.513 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES Ultra-Wideband Operation § 15.513 Technical requirements for medical imaging systems. (a) The UWB...

INDOT Technical Training Plan : [Technical Summary

DOT National Transportation Integrated Search

2012-01-01

A wide range of job classifications, increasing technical : performance expectations, licensing and certification requirements, : budget restrictions and frequent department : reorganization has made technical training of employees : more difficult, ...

Airborne Laser Remote Sensor for Oil Detection and Classification : Engineering Requirements and Technical Considerations Relevant to a Performance Specification

DOT National Transportation Integrated Search

1975-08-01

This report outlines the engineering requirements for an Airborne Laser Remote Sensor for Oil Detection and Classification System. Detailed engineering requirements are given for the major units of the system. Technical considerations pertinent to a ...

47 CFR 15.515 - Technical requirements for vehicular radar systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 1 2011-10-01 2011-10-01 false Technical requirements for vehicular radar... DEVICES Ultra-Wideband Operation § 15.515 Technical requirements for vehicular radar systems. (a..., changing gears, or engaging a turn signal. (b) The UWB bandwidth of a vehicular radar system operating...

47 CFR 15.515 - Technical requirements for vehicular radar systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Technical requirements for vehicular radar... DEVICES Ultra-Wideband Operation § 15.515 Technical requirements for vehicular radar systems. (a..., changing gears, or engaging a turn signal. (b) The UWB bandwidth of a vehicular radar system operating...

47 CFR 15.515 - Technical requirements for vehicular radar systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 1 2014-10-01 2014-10-01 false Technical requirements for vehicular radar... DEVICES Ultra-Wideband Operation § 15.515 Technical requirements for vehicular radar systems. (a..., changing gears, or engaging a turn signal. (b) The UWB bandwidth of a vehicular radar system operating...

47 CFR 15.515 - Technical requirements for vehicular radar systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 1 2013-10-01 2013-10-01 false Technical requirements for vehicular radar... DEVICES Ultra-Wideband Operation § 15.515 Technical requirements for vehicular radar systems. (a..., changing gears, or engaging a turn signal. (b) The UWB bandwidth of a vehicular radar system operating...

47 CFR 15.515 - Technical requirements for vehicular radar systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 1 2012-10-01 2012-10-01 false Technical requirements for vehicular radar... DEVICES Ultra-Wideband Operation § 15.515 Technical requirements for vehicular radar systems. (a..., changing gears, or engaging a turn signal. (b) The UWB bandwidth of a vehicular radar system operating...

38 CFR 61.52 - Threshold requirements for technical assistance grant applications.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Threshold requirements....52 Threshold requirements for technical assistance grant applications. To be eligible for a technical assistance grant, an applicant must meet the following threshold requirements: (a) The application included...

38 CFR 61.52 - Threshold requirements for technical assistance grant applications.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2012-07-01 2012-07-01 false Threshold requirements....52 Threshold requirements for technical assistance grant applications. To be eligible for a technical assistance grant, an applicant must meet the following threshold requirements: (a) The application included...

Do PICU patients meet technical criteria for performing indirect calorimetry?

PubMed

Beggs, Megan R; Garcia Guerra, Gonzalo; Larsen, Bodil M K

2016-10-01

Indirect calorimetry (IC) is considered gold standard for assessing energy needs of critically ill children as predictive equations and clinical status indicators are often unreliable. Accurate assessment of energy requirements in this vulnerable population is essential given the high risk of over or underfeeding and the consequences thereof. The proportion of patients and patient days in pediatric intensive care (PICU) for which energy expenditure (EE) can be measured using IC is currently unknown. In the current study, we aimed to quantify the daily proportion of consecutive PICU patients who met technical criteria to perform indirect calorimetry and describe the technical contraindications when criteria were not met. Prospective, observational, single-centre study conducted in a cardiac and general PICU. All consecutive patients admitted for at least 96 h were included in the study. Variables collected for each patient included age at admission, admission diagnosis, and if technical criteria for indirect calorimetry were met. Technical criteria variables were collected within the same 2 h each morning and include: provision of supplemental oxygen, ventilator settings, endotracheal tube (ETT) leak, diagnosis of chest tube air leak, provision of external gas support (i.e. nitric oxide), and provision of extracorporeal membrane oxygenation (ECMO). 288 patients were included for a total of 3590 patient days between June 2014 and February 2015. The main reasons for admission were: surgery (cardiac and non-cardiac), respiratory distress, trauma, oncology and medicine/other. The median (interquartile range) patient age was 0.7 (0.3-4.6) years. The median length of PICU stay was 7 (5-14) days. Only 34% (95% CI, 32.4-35.5%) of patient days met technical criteria for IC. For patients less than 6 months of age, technical criteria were met on significantly fewer patient days (29%, p < 0.01). Moreover, 27% of patients did not meet technical criteria for IC on any day

47 CFR 74.861 - Technical requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

..., AUXILIARY, SPECIAL BROADCAST AND OTHER PROGRAM DISTRIBUTIONAL SERVICES Low Power Auxiliary Stations § 74.861 Technical requirements. (a) Transmitter power is the power at the transmitter output terminals and delivered... the purpose of this subpart, the transmitter power is the carrier power. (b) Each authorization for a...

47 CFR 68.604 - Requirements for submitting technical criteria.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 3 2010-10-01 2010-10-01 false Requirements for submitting technical criteria. 68.604 Section 68.604 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER...) may establish technical criteria for terminal equipment pursuant to ANSI consensus decision-making...

30 CFR 7.24 - Technical requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Brattice Cloth and Ventilation Tubing § 7.24 Technical requirements. (a) Brattice cloth shall be flame resistant when tested in accordance with... MSHA-approved brattice cloth. If a supporting structure is used, it shall be metal or other...

30 CFR 7.24 - Technical requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Brattice Cloth and Ventilation Tubing § 7.24 Technical requirements. (a) Brattice cloth shall be flame resistant when tested in accordance with... MSHA-approved brattice cloth. If a supporting structure is used, it shall be metal or other...

30 CFR 7.24 - Technical requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Brattice Cloth and Ventilation Tubing § 7.24 Technical requirements. (a) Brattice cloth shall be flame resistant when tested in accordance with... MSHA-approved brattice cloth. If a supporting structure is used, it shall be metal or other...

30 CFR 7.24 - Technical requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Brattice Cloth and Ventilation Tubing § 7.24 Technical requirements. (a) Brattice cloth shall be flame resistant when tested in accordance with... MSHA-approved brattice cloth. If a supporting structure is used, it shall be metal or other...

30 CFR 7.24 - Technical requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Brattice Cloth and Ventilation Tubing § 7.24 Technical requirements. (a) Brattice cloth shall be flame resistant when tested in accordance with... MSHA-approved brattice cloth. If a supporting structure is used, it shall be metal or other...

32 CFR 203.17 - Technical assistance provider reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 2 2010-07-01 2010-07-01 false Technical assistance provider reporting requirements. 203.17 Section 203.17 National Defense Department of Defense (Continued) OFFICE OF THE SECRETARY... technical assistance provider shall submit progress reports, financial status reports, materials prepared...

32 CFR 203.17 - Technical assistance provider reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 2 2014-07-01 2014-07-01 false Technical assistance provider reporting requirements. 203.17 Section 203.17 National Defense Department of Defense (Continued) OFFICE OF THE SECRETARY... technical assistance provider shall submit progress reports, financial status reports, materials prepared...

32 CFR 203.17 - Technical assistance provider reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 2 2013-07-01 2013-07-01 false Technical assistance provider reporting requirements. 203.17 Section 203.17 National Defense Department of Defense (Continued) OFFICE OF THE SECRETARY... technical assistance provider shall submit progress reports, financial status reports, materials prepared...

32 CFR 203.17 - Technical assistance provider reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 2 2011-07-01 2011-07-01 false Technical assistance provider reporting requirements. 203.17 Section 203.17 National Defense Department of Defense (Continued) OFFICE OF THE SECRETARY... technical assistance provider shall submit progress reports, financial status reports, materials prepared...

32 CFR 203.17 - Technical assistance provider reporting requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 2 2012-07-01 2012-07-01 false Technical assistance provider reporting requirements. 203.17 Section 203.17 National Defense Department of Defense (Continued) OFFICE OF THE SECRETARY... technical assistance provider shall submit progress reports, financial status reports, materials prepared...

Relationship between non-technical skills and technical performance during cardiopulmonary resuscitation: does stress have an influence?

PubMed Central

Krage, Ralf; Zwaan, Laura; Tjon Soei Len, Lian; Kolenbrander, Mark W; van Groeningen, Dick; Loer, Stephan A; Wagner, Cordula; Schober, Patrick

2017-01-01

Background Non-technical skills, such as task management, leadership, situational awareness, communication and decision-making refer to cognitive, behavioural and social skills that contribute to safe and efficient team performance. The importance of these skills during cardiopulmonary resuscitation (CPR) is increasingly emphasised. Nonetheless, the relationship between non-technical skills and technical performance is poorly understood. We hypothesise that non-technical skills become increasingly important under stressful conditions when individuals are distracted from their tasks, and investigated the relationship between non-technical and technical skills under control conditions and when external stressors are present. Methods In this simulator-based randomised cross-over study, 30 anaesthesiologists and anaesthesia residents from the VU University Medical Center, Amsterdam, the Netherlands, participated in two different CPR scenarios in random order. In one scenario, external stressors (radio noise and a distractive scripted family member) were added, while the other scenario without stressors served as control condition. Non-technical performance of the team leader and technical performance of the team were measured using the ‘Anaesthetists’ Non-technical Skill’ score and a recently developed technical skills score. Analysis of variance and Pearson correlation coefficients were used for statistical analyses. Results Non-technical performance declined when external stressors were present (adjusted mean difference 3.9 points, 95% CI 2.4 to 5.5 points). A significant correlation between non-technical and technical performance scores was observed when external stressors were present (r=0.67, 95% CI 0.40 to 0.83, p<0.001), while no evidence for such a relationship was observed under control conditions (r=0.15, 95% CI −0.22 to 0.49, p=0.42). This was equally true for all individual domains of the non-technical performance score (task management, team

Technical and tactical skills related to performance levels in tennis: A systematic review.

PubMed

Kolman, Nikki S; Kramer, Tamara; Elferink-Gemser, Marije T; Huijgen, Barbara C H; Visscher, Chris

2018-06-11

The aim of this systematic review is to provide an overview of outcome measures and instruments identified in the literature for examining technical and tactical skills in tennis related to performance levels. Such instruments can be used to identify talent or the specific skill development training needs of particular players. Searches for this review were conducted using the PubMed, Web of Science, and PsycInfo databases. Out of 733 publications identified through these searches, 40 articles were considered relevant and included in this study. They were divided into three categories: (1) technical skills, (2) tactical skills and (3) integrated technical and tactical skills. There was strong evidence that technical skills (ball velocity and to a lesser extent ball accuracy) and tactical skills (decision making, anticipation, tactical knowledge and visual search strategies) differed among players according to their performance levels. However, integrated measurement of these skills is required, because winning a point largely hinges on a tactical decision to perform a particular stroke (i.e., technical execution). Therefore, future research should focus on examining the relationship between these skills and tennis performance and on the development of integrated methods for measuring these skills.

30 CFR 7.44 - Technical requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Battery Assemblies § 7.44 Technical requirements. (a)(1) Battery boxes and covers constructed of AISI 1010 hot rolled steel shall have the following minimum thicknesses based on the total weight of a unit of the battery assembly charged and ready...

30 CFR 7.44 - Technical requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... APPROVAL OF MINING PRODUCTS TESTING BY APPLICANT OR THIRD PARTY Battery Assemblies § 7.44 Technical requirements. (a)(1) Battery boxes and covers constructed of AISI 1010 hot rolled steel shall have the following minimum thicknesses based on the total weight of a unit of the battery assembly charged and ready...

Review of PREPA Technical Requirements for Interconnecting Wind and Solar Generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gevorgian, Vahan; Booth, Sarah

2013-11-01

The Puerto Rico Electric Power Authority developed the minimum technical requirements for interconnection of wind turbine generation and photovoltaic power plants. NREL has conducted a review of these requirements based on generic technical aspects and electrical characteristics of wind and photovoltaic power plants, and on existing requirements from other utilities (both U.S. and European).

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

Relationship between non-technical skills and technical performance during cardiopulmonary resuscitation: does stress have an influence?

PubMed

Krage, Ralf; Zwaan, Laura; Tjon Soei Len, Lian; Kolenbrander, Mark W; van Groeningen, Dick; Loer, Stephan A; Wagner, Cordula; Schober, Patrick

2017-11-01

Non-technical skills, such as task management, leadership, situational awareness, communication and decision-making refer to cognitive, behavioural and social skills that contribute to safe and efficient team performance. The importance of these skills during cardiopulmonary resuscitation (CPR) is increasingly emphasised. Nonetheless, the relationship between non-technical skills and technical performance is poorly understood. We hypothesise that non-technical skills become increasingly important under stressful conditions when individuals are distracted from their tasks, and investigated the relationship between non-technical and technical skills under control conditions and when external stressors are present. In this simulator-based randomised cross-over study, 30 anaesthesiologists and anaesthesia residents from the VU University Medical Center, Amsterdam, the Netherlands, participated in two different CPR scenarios in random order. In one scenario, external stressors (radio noise and a distractive scripted family member) were added, while the other scenario without stressors served as control condition. Non-technical performance of the team leader and technical performance of the team were measured using the 'Anaesthetists' Non-technical Skill' score and a recently developed technical skills score. Analysis of variance and Pearson correlation coefficients were used for statistical analyses. Non-technical performance declined when external stressors were present (adjusted mean difference 3.9 points, 95% CI 2.4 to 5.5 points). A significant correlation between non-technical and technical performance scores was observed when external stressors were present (r=0.67, 95% CI 0.40 to 0.83, p<0.001), while no evidence for such a relationship was observed under control conditions (r=0.15, 95% CI -0.22 to 0.49, p=0.42). This was equally true for all individual domains of the non-technical performance score (task management, team working, situation awareness, decision

44 CFR 65.3 - Requirement to submit new technical data.

Code of Federal Regulations, 2011 CFR

2011-10-01

... available, a community shall notify the Administrator of the changes by submitting technical or scientific... IDENTIFICATION AND MAPPING OF SPECIAL HAZARD AREAS § 65.3 Requirement to submit new technical data. A community's...

47 CFR 18.109 - General technical requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 1 2011-10-01 2011-10-01 false General technical requirements. 18.109 Section 18.109 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL INDUSTRIAL, SCIENTIFIC, AND... designed and constructed in accordance with good engineering practice with sufficient shielding and...

47 CFR 18.109 - General technical requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 1 2012-10-01 2012-10-01 false General technical requirements. 18.109 Section 18.109 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL INDUSTRIAL, SCIENTIFIC, AND... designed and constructed in accordance with good engineering practice with sufficient shielding and...

47 CFR 18.109 - General technical requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false General technical requirements. 18.109 Section 18.109 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL INDUSTRIAL, SCIENTIFIC, AND... designed and constructed in accordance with good engineering practice with sufficient shielding and...

47 CFR 18.109 - General technical requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 1 2013-10-01 2013-10-01 false General technical requirements. 18.109 Section 18.109 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL INDUSTRIAL, SCIENTIFIC, AND... designed and constructed in accordance with good engineering practice with sufficient shielding and...

47 CFR 18.109 - General technical requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 1 2014-10-01 2014-10-01 false General technical requirements. 18.109 Section 18.109 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL INDUSTRIAL, SCIENTIFIC, AND... designed and constructed in accordance with good engineering practice with sufficient shielding and...

Using Technical Performance Measures

NASA Technical Reports Server (NTRS)

Garrett, Christopher J.; Levack, Daniel J. H.; Rhodes, Russel E.

2011-01-01

All programs have requirements. For these requirements to be met, there must be a means of measurement. A Technical Performance Measure (TPM) is defined to produce a measured quantity that can be compared to the requirement. In practice, the TPM is often expressed as a maximum or minimum and a goal. Example TPMs for a rocket program are: vacuum or sea level specific impulse (lsp), weight, reliability (often expressed as a failure rate), schedule, operability (turn-around time), design and development cost, production cost, and operating cost. Program status is evaluated by comparing the TPMs against specified values of the requirements. During the program many design decisions are made and most of them affect some or all of the TPMs. Often, the same design decision changes some TPMs favorably while affecting other TPMs unfavorably. The problem then becomes how to compare the effects of a design decision on different TPMs. How much failure rate is one second of specific impulse worth? How many days of schedule is one pound of weight worth? In other words, how to compare dissimilar quantities in order to trade and manage the TPMs to meet all requirements. One method that has been used successfully and has a mathematical basis is Utility Analysis. Utility Analysis enables quantitative comparison among dissimilar attributes. It uses a mathematical model that maps decision maker preferences over the tradeable range of each attribute. It is capable of modeling both independent and dependent attributes. Utility Analysis is well supported in the literature on Decision Theory. It has been used at Pratt & Whitney Rocketdyne for internal programs and for contracted work such as the J-2X rocket engine program. This paper describes the construction of TPMs and describes Utility Analysis. It then discusses the use of TPMs in design trades and to manage margin during a program using Utility Analysis.

38 CFR 61.52 - Threshold requirements for technical assistance grant applications.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2011-07-01 2011-07-01 false Threshold requirements for technical assistance grant applications. 61.52 Section 61.52 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS (CONTINUED) VA HOMELESS PROVIDERS GRANT AND PER DIEM PROGRAM § 61.52 Threshold requirements for technical assistanc...

16 CFR 1406.4 - Requirements to provide performance and technical notice to prospective purchasers and purchasers.

Code of Federal Regulations, 2014 CFR

2014-01-01

... CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT SAFETY ACT REGULATIONS COAL AND WOOD BURNING APPLIANCES... burning appliances as defined in § 1406.3 shall give notification of performance and technical data...: Creosote Formation and Need for Removal When wood is burned slowly, it produces tar and other vapors, which...

16 CFR 1406.4 - Requirements to provide performance and technical notice to prospective purchasers and purchasers.

Code of Federal Regulations, 2012 CFR

2012-01-01

... CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT SAFETY ACT REGULATIONS COAL AND WOOD BURNING APPLIANCES... burning appliances as defined in § 1406.3 shall give notification of performance and technical data...: Creosote Formation and Need for Removal When wood is burned slowly, it produces tar and other vapors, which...

47 CFR 15.611 - General technical requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false General technical requirements. 15.611 Section 15.611 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES Access... shut-off procedure, by the use of a non-volatile memory, or some other method, to immediately restore...

38 CFR 61.52 - Technical assistance grant application packages-threshold requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2014-07-01 2014-07-01 false Technical assistance grant application packages-threshold requirements. 61.52 Section 61.52 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS (CONTINUED) VA HOMELESS PROVIDERS GRANT AND PER DIEM PROGRAM Technical Assistance Grants § 61.52 Technical...

38 CFR 61.52 - Technical assistance grant application packages-threshold requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2013-07-01 2013-07-01 false Technical assistance grant application packages-threshold requirements. 61.52 Section 61.52 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS (CONTINUED) VA HOMELESS PROVIDERS GRANT AND PER DIEM PROGRAM Technical Assistance Grants § 61.52 Technical...

48 CFR 216.402-2 - Technical performance incentives.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Technical performance incentives. 216.402-2 Section 216.402-2 Federal Acquisition Regulations System DEFENSE ACQUISITION... Contracts 216.402-2 Technical performance incentives. See PGI 216.402-2 for guidance on establishing...

47 CFR 15.510 - Technical requirements for through D-wall imaging systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Technical requirements for through D-wall imaging systems. 15.510 Section 15.510 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES Ultra-Wideband Operation § 15.510 Technical requirements for through D-wall imaging...

44 CFR 65.3 - Requirement to submit new technical data.

Code of Federal Regulations, 2010 CFR

2010-10-01

... technical data. 65.3 Section 65.3 Emergency Management and Assistance FEDERAL EMERGENCY MANAGEMENT AGENCY... IDENTIFICATION AND MAPPING OF SPECIAL HAZARD AREAS § 65.3 Requirement to submit new technical data. A community's base flood elevations may increase or decrease resulting from physical changes affecting flooding...

Technical skills requirement of Indonesian construction labors to work in Malaysia

NASA Astrophysics Data System (ADS)

Adi, Henny Pratiwi

2017-03-01

Labors skills is an important part of construction projects implementation. Suitability between the skills possessed by labors with the skills needed by user is required to increase employment opportunities. Malaysia is a country that using construction labors from Indonesia. This study aims to get the kind of technical skills required by users of Indonesian constructian labors in Malaysia and also the importance level of technical skills. Data collecting in this research was conducted through interviews and questionnaires on contractors in Malaysia. The next stage was determine the importance level of technical skills in work field of carpenter, bricklayer, plumber and painters. The importance level of technical skills analyzed using the Relative Importance Index (RII). The results showed that mastering the operation of both instruments either manually or electrically is the most importance in the technical skills. Therefore, an understanding of the types of equipment for work field and the manner of operation is need to had by Indonesian construction labors who will work in Malaysia.

Maintaining technical excellence requires a national plan

NASA Technical Reports Server (NTRS)

Davidson, T. F.

1991-01-01

To meet the challenge of technical excellence, AIA established a rocket propulsion committee to develop the National Rocket Propulsion Strategic Plan. Developing such a plan required a broad spectrum of experience and disciplines. The Strategic Plan team needed the participation of industry, government, and academia. The plan provides, if followed, a means for the U.S. to maintain technical excellence and world leadership in rocket propulsion. To implement the National Rocket Propulsion Strategic Plan is to invest in the social, economic, and technological futures of America. The plan lays the basis for upgrading existing propulsion systems and a firm base for future full scale development, production, and operation of rocket propulsion systems for space, defense, and commercial applications.

Handbook of Human Performance Measures and Crew Requirements for Flight Deck Research

DOT National Transportation Integrated Search

1995-12-01

The Federal Aviation Administration (FAA) Technical Center envisions that their : studies will require standard measure of pilot/crew performance. Therefore, : the FAA commissioned the Crew System Ergonomics Information Analysis Center : (CSERIAC) to...

9 CFR 351.16 - Certificate required for shipments of technical animal fat.

Code of Federal Regulations, 2010 CFR

2010-01-01

... technical animal fat. 351.16 Section 351.16 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE... AND VOLUNTARY INSPECTION AND CERTIFICATION CERTIFICATION OF TECHNICAL ANIMAL FATS FOR EXPORT Transportation and Exportation of Certified Technical Animal Fat § 351.16 Certificate required for shipments of...

9 CFR 351.16 - Certificate required for shipments of technical animal fat.

Code of Federal Regulations, 2012 CFR

2012-01-01

... technical animal fat. 351.16 Section 351.16 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE... AND VOLUNTARY INSPECTION AND CERTIFICATION CERTIFICATION OF TECHNICAL ANIMAL FATS FOR EXPORT Transportation and Exportation of Certified Technical Animal Fat § 351.16 Certificate required for shipments of...

9 CFR 351.16 - Certificate required for shipments of technical animal fat.

Code of Federal Regulations, 2011 CFR

2011-01-01

... technical animal fat. 351.16 Section 351.16 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE... AND VOLUNTARY INSPECTION AND CERTIFICATION CERTIFICATION OF TECHNICAL ANIMAL FATS FOR EXPORT Transportation and Exportation of Certified Technical Animal Fat § 351.16 Certificate required for shipments of...

9 CFR 351.16 - Certificate required for shipments of technical animal fat.

Code of Federal Regulations, 2014 CFR

2014-01-01

... technical animal fat. 351.16 Section 351.16 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE... AND VOLUNTARY INSPECTION AND CERTIFICATION CERTIFICATION OF TECHNICAL ANIMAL FATS FOR EXPORT Transportation and Exportation of Certified Technical Animal Fat § 351.16 Certificate required for shipments of...

9 CFR 351.16 - Certificate required for shipments of technical animal fat.

Code of Federal Regulations, 2013 CFR

2013-01-01

... technical animal fat. 351.16 Section 351.16 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE... AND VOLUNTARY INSPECTION AND CERTIFICATION CERTIFICATION OF TECHNICAL ANIMAL FATS FOR EXPORT Transportation and Exportation of Certified Technical Animal Fat § 351.16 Certificate required for shipments of...

16 CFR § 1406.4 - Requirements to provide performance and technical notice to prospective purchasers and purchasers.

Code of Federal Regulations, 2013 CFR

2013-01-01

... CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT SAFETY ACT REGULATIONS COAL AND WOOD BURNING APPLIANCES... burning appliances as defined in § 1406.3 shall give notification of performance and technical data... follows: Creosote Formation and Need for Removal When wood is burned slowly, it produces tar and other...

75 FR 6683 - Notice of Proposed Information Collection: Comment Request; Technical Processing Requirements for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-10

... Information Collection: Comment Request; Technical Processing Requirements for Multifamily Project Mortgage... information: Title of Proposal: Technical Processing Requirements for Multifamily Project Mortgage Insurance... information collection requirement described below will be submitted to the Office of Management and Budget...

75 FR 18505 - International Cooperation on Harmonisation of Technical Requirements for Registration of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-12

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2010-D-0165] International Cooperation on Harmonisation of Technical Requirements for Registration of Veterinary Medicinal... veterinary use by the International Cooperation on Harmonisation of Technical Requirements for Registration...

19 CFR 115.30 - Technical requirements for containers by design type.

Code of Federal Regulations, 2011 CFR

2011-04-01

... SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.30 Technical... 19 Customs Duties 1 2011-04-01 2011-04-01 false Technical requirements for containers by design...

19 CFR 115.30 - Technical requirements for containers by design type.

Code of Federal Regulations, 2012 CFR

2012-04-01

... SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.30 Technical... 19 Customs Duties 1 2012-04-01 2012-04-01 false Technical requirements for containers by design...

19 CFR 115.30 - Technical requirements for containers by design type.

Code of Federal Regulations, 2014 CFR

2014-04-01

... SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.30 Technical... 19 Customs Duties 1 2014-04-01 2014-04-01 false Technical requirements for containers by design...

19 CFR 115.30 - Technical requirements for containers by design type.

Code of Federal Regulations, 2010 CFR

2010-04-01

... SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.30 Technical... 19 Customs Duties 1 2010-04-01 2010-04-01 false Technical requirements for containers by design...

19 CFR 115.30 - Technical requirements for containers by design type.

Code of Federal Regulations, 2013 CFR

2013-04-01

... SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS CONVENTIONS Procedures for Approval of Containers by Design Type § 115.30 Technical... 19 Customs Duties 1 2013-04-01 2013-04-01 false Technical requirements for containers by design...

19 CFR 115.40 - Technical requirements for containers.

Code of Federal Regulations, 2010 CFR

2010-04-01

...; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS... containers. A container that is submitted for inspection for approval after manufacture, must comply with the... 19 Customs Duties 1 2010-04-01 2010-04-01 false Technical requirements for containers. 115.40...

19 CFR 115.40 - Technical requirements for containers.

Code of Federal Regulations, 2012 CFR

2012-04-01

...; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS... containers. A container that is submitted for inspection for approval after manufacture, must comply with the... 19 Customs Duties 1 2012-04-01 2012-04-01 false Technical requirements for containers. 115.40...

19 CFR 115.40 - Technical requirements for containers.

Code of Federal Regulations, 2011 CFR

2011-04-01

...; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS... containers. A container that is submitted for inspection for approval after manufacture, must comply with the... 19 Customs Duties 1 2011-04-01 2011-04-01 false Technical requirements for containers. 115.40...

19 CFR 115.40 - Technical requirements for containers.

Code of Federal Regulations, 2013 CFR

2013-04-01

...; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS... containers. A container that is submitted for inspection for approval after manufacture, must comply with the... 19 Customs Duties 1 2013-04-01 2013-04-01 false Technical requirements for containers. 115.40...

19 CFR 115.40 - Technical requirements for containers.

Code of Federal Regulations, 2014 CFR

2014-04-01

...; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO INTERNATIONAL CUSTOMS... containers. A container that is submitted for inspection for approval after manufacture, must comply with the... 19 Customs Duties 1 2014-04-01 2014-04-01 false Technical requirements for containers. 115.40...

Technical performance and match-to-match variation in elite football teams.

PubMed

Liu, Hongyou; Gómez, Miguel-Angel; Gonçalves, Bruno; Sampaio, Jaime

2016-01-01

Recent research suggests that match-to-match variation adds important information to performance descriptors in team sports, as it helps measure how players fine-tune their tactical behaviours and technical actions to the extreme dynamical environments. The current study aims to identify the differences in technical performance of players from strong and weak teams and to explore match-to-match variation of players' technical match performance. Performance data of all the 380 matches of season 2012-2013 in the Spanish First Division Professional Football League were analysed. Twenty-one performance-related match actions and events were chosen as variables in the analyses. Players' technical performance profiles were established by unifying count values of each action or event of each player per match into the same scale. Means of these count values of players from Top3 and Bottom3 teams were compared and plotted into radar charts. Coefficient of variation of each match action or event within a player was calculated to represent his match-to-match variation of technical performance. Differences in the variation of technical performances of players across different match contexts (team and opposition strength, match outcome and match location) were compared. All the comparisons were achieved by the magnitude-based inferences. Results showed that technical performances differed between players of strong and weak teams from different perspectives across different field positions. Furthermore, the variation of the players' technical performance is affected by the match context, with effects from team and opposition strength greater than effects from match location and match outcome.

48 CFR 1816.402-270 - NASA technical performance incentives.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 6 2013-10-01 2013-10-01 false NASA technical performance incentives. 1816.402-270 Section 1816.402-270 Federal Acquisition Regulations System NATIONAL AERONAUTICS AND....402-270 NASA technical performance incentives. (a) Pursuant to the guidelines in 1816.402, NASA has...

48 CFR 1816.402-270 - NASA technical performance incentives.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true NASA technical performance incentives. 1816.402-270 Section 1816.402-270 Federal Acquisition Regulations System NATIONAL AERONAUTICS AND....402-270 NASA technical performance incentives. (a) Pursuant to the guidelines in 1816.402, NASA has...

48 CFR 1816.402-270 - NASA technical performance incentives.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 6 2014-10-01 2014-10-01 false NASA technical performance incentives. 1816.402-270 Section 1816.402-270 Federal Acquisition Regulations System NATIONAL AERONAUTICS AND....402-270 NASA technical performance incentives. (a) Pursuant to the guidelines in 1816.402, NASA has...

48 CFR 1816.402-270 - NASA technical performance incentives.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 6 2011-10-01 2011-10-01 false NASA technical performance incentives. 1816.402-270 Section 1816.402-270 Federal Acquisition Regulations System NATIONAL AERONAUTICS AND....402-270 NASA technical performance incentives. (a) Pursuant to the guidelines in 1816.402, NASA has...

48 CFR 1816.402-270 - NASA technical performance incentives.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 6 2012-10-01 2012-10-01 false NASA technical performance incentives. 1816.402-270 Section 1816.402-270 Federal Acquisition Regulations System NATIONAL AERONAUTICS AND....402-270 NASA technical performance incentives. (a) Pursuant to the guidelines in 1816.402, NASA has...

Additive Manufacturing in Production: A Study Case Applying Technical Requirements

NASA Astrophysics Data System (ADS)

Ituarte, Iñigo Flores; Coatanea, Eric; Salmi, Mika; Tuomi, Jukka; Partanen, Jouni

Additive manufacturing (AM) is expanding the manufacturing capabilities. However, quality of AM produced parts is dependent on a number of machine, geometry and process parameters. The variability of these parameters affects the manufacturing drastically and therefore standardized processes and harmonized methodologies need to be developed to characterize the technology for end use applications and enable the technology for manufacturing. This research proposes a composite methodology integrating Taguchi Design of Experiments, multi-objective optimization and statistical process control, to optimize the manufacturing process and fulfil multiple requirements imposed to an arbitrary geometry. The proposed methodology aims to characterize AM technology depending upon manufacturing process variables as well as to perform a comparative assessment of three AM technologies (Selective Laser Sintering, Laser Stereolithography and Polyjet). Results indicate that only one machine, laser-based Stereolithography, was feasible to fulfil simultaneously macro and micro level geometrical requirements but mechanical properties were not at required level. Future research will study a single AM system at the time to characterize AM machine technical capabilities and stimulate pre-normative initiatives of the technology for end use applications.

78 FR 64146 - 30-Day Notice of Proposed Information Collection: Technical Processing Requirements for...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-25

... Information Collection: Technical Processing Requirements for Multifamily Project Mortgage Insurance AGENCY: Office of the Chief Information Officer, HUD. ACTION: Notice. SUMMARY: HUD has submitted the proposed... Information Collection Title of Information Collection: Technical Processing Requirements for Multifamily...

78 FR 65695 - 30-Day Notice of Proposed Information Collection: Technical Processing Requirements for...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-01

... Information Collection: Technical Processing Requirements for Multifamily Project Mortgage Insurance AGENCY: Office of the Chief Information Officer, HUD. ACTION: Correction, notice. SUMMARY: On October 25, 2013 at... Collection Title of Information Collection: Technical Processing Requirements for Multifamily Project...

Vocational and Technical Education Performance Standards and Competencies.

ERIC Educational Resources Information Center

Connecticut State Board of Education, Hartford.

These Connecticut vocational and technical performance standards and competencies are a guide for overall quality attainment in these seven vocational and technical program areas: agricultural science technology education; business and finance technology education; cooperative work education; family and consumer sciences education; marketing…

47 CFR 80.231 - Technical Requirements for Class B Automatic Identification System (AIS) equipment.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Identification System (AIS) equipment. 80.231 Section 80.231 Telecommunication FEDERAL COMMUNICATIONS COMMISSION... § 80.231 Technical Requirements for Class B Automatic Identification System (AIS) equipment. (a) Class B Automatic Identification System (AIS) equipment must meet the technical requirements of IEC 62287...

47 CFR 80.231 - Technical Requirements for Class B Automatic Identification System (AIS) equipment.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Identification System (AIS) equipment. 80.231 Section 80.231 Telecommunication FEDERAL COMMUNICATIONS COMMISSION... § 80.231 Technical Requirements for Class B Automatic Identification System (AIS) equipment. (a) Class B Automatic Identification System (AIS) equipment must meet the technical requirements of IEC 62287...

47 CFR 80.231 - Technical Requirements for Class B Automatic Identification System (AIS) equipment.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Identification System (AIS) equipment. 80.231 Section 80.231 Telecommunication FEDERAL COMMUNICATIONS COMMISSION... § 80.231 Technical Requirements for Class B Automatic Identification System (AIS) equipment. (a) Class B Automatic Identification System (AIS) equipment must meet the technical requirements of IEC 62287...

Framework conditions and requirements to ensure the technical functional safety of reprocessed medical devices.

PubMed

Kraft, Marc

2008-09-03

Testing and restoring technical-functional safety is an essential part of medical device reprocessing. Technical functional tests have to be carried out on the medical device in the course of the validation of reprocessing procedures. These ensure (in addition to the hygiene tests) that the reprocessing procedure is suitable for the medical device. Functional tests are, however, also a part of reprocessing procedures. As a stage in the reprocessing, they ensure for the individual medical device that no damage or other changes limit the performance. When determining which technical-functional tests are to be carried out, the current technological standard has to be taken into account in the form of product-specific and process-oriented norms. Product-specific norms primarily define safety-relevant requirements. The risk management method described in DIN EN ISO 14971 is the basis for recognising hazards; the likelihood of such hazards arising can be minimised through additional technical-functional tests, which may not yet have been standardised. Risk management is part of a quality management system, which must be bindingly certified for manufacturers and processors of critical medical devices with particularly high processing demands by a body accredited by the competent authority.

Framework conditions and requirements to ensure the technical functional safety of reprocessed medical devices

PubMed Central

Kraft, Marc

2008-01-01

Testing and restoring technical-functional safety is an essential part of medical device reprocessing. Technical functional tests have to be carried out on the medical device in the course of the validation of reprocessing procedures. These ensure (in addition to the hygiene tests) that the reprocessing procedure is suitable for the medical device. Functional tests are, however, also a part of reprocessing procedures. As a stage in the reprocessing, they ensure for the individual medical device that no damage or other changes limit the performance. When determining which technical-functional tests are to be carried out, the current technological standard has to be taken into account in the form of product-specific and process-oriented norms. Product-specific norms primarily define safety-relevant requirements. The risk management method described in DIN EN ISO 14971 is the basis for recognising hazards; the likelihood of such hazards arising can be minimised through additional technical-functional tests, which may not yet have been standardised. Risk management is part of a quality management system, which must be bindingly certified for manufacturers and processors of critical medical devices with particularly high processing demands by a body accredited by the competent authority. PMID:20204095

Not just trust: factors influencing learners' attempts to perform technical skills on real patients.

PubMed

Bannister, Susan L; Dolson, Mark S; Lingard, Lorelei; Keegan, David A

2018-06-01

As part of their training, physicians are required to learn how to perform technical skills on patients. The previous literature reveals that this learning is complex and that many opportunities to perform these skills are not converted into attempts to do so by learners. This study sought to explore and understand this phenomenon better. A multi-phased qualitative study including ethnographic observations, interviews and focus groups was conducted to explore the factors that influence technical skill learning. In a tertiary paediatric emergency department, staff physician preceptors, residents, nurses and respiratory therapists were observed in the delivery and teaching of technical skills over a 3-month period. A constant comparison methodology was used to analyse the data and to develop a constructivist grounded theory. We conducted 419 hours of observation, 18 interviews and four focus groups. We observed 287 instances of technical skills, of which 27.5% were attempted by residents. Thematic analysis identified 14 factors, grouped into three categories, which influenced whether residents attempted technical skills on real patients. Learner factors included resident initiative, perceived need for skill acquisition and competing priorities. Teacher factors consisted of competing priorities, interest in teaching, perceived need for residents to acquire skills, attributions about learners, assessments of competency, and trust. Environmental factors were competition from other learners, judgement that the patient was appropriate, buy-in from team members, consent from patient or caregivers, and physical environment constraints. Our findings suggest that neither the presence of a learner in a clinical environment nor the trust of the supervisor is sufficient to ensure the learner will attempt a technical skill. We characterise this phenomenon as representing a pool of opportunities to conduct technical skills on live patients that shrinks to a much smaller pool of

16 CFR 1407.3 - Providing performance and technical data to purchasers by labeling.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 16 Commercial Practices 2 2014-01-01 2014-01-01 false Providing performance and technical data to... TECHNICAL DATA BY LABELING § 1407.3 Providing performance and technical data to purchasers by labeling. (a... technical data related to performance and safety to prospective purchasers of such products at the time of...

16 CFR 1407.3 - Providing performance and technical data to purchasers by labeling.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Providing performance and technical data to... TECHNICAL DATA BY LABELING § 1407.3 Providing performance and technical data to purchasers by labeling. (a... technical data related to performance and safety to prospective purchasers of such products at the time of...

16 CFR 1407.3 - Providing performance and technical data to purchasers by labeling.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 16 Commercial Practices 2 2012-01-01 2012-01-01 false Providing performance and technical data to... TECHNICAL DATA BY LABELING § 1407.3 Providing performance and technical data to purchasers by labeling. (a... technical data related to performance and safety to prospective purchasers of such products at the time of...

16 CFR 1407.3 - Providing performance and technical data to purchasers by labeling.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 16 Commercial Practices 2 2011-01-01 2011-01-01 false Providing performance and technical data to... TECHNICAL DATA BY LABELING § 1407.3 Providing performance and technical data to purchasers by labeling. (a... technical data related to performance and safety to prospective purchasers of such products at the time of...

High School Graduation Minimum Competency Requirements. Final Technical Report.

ERIC Educational Resources Information Center

Austin Independent School District, TX. Office of Research and Evaluation.

This technical report details the testing results and analyses supporting the evaluation findings related to the Austin (Texas) Independent School District (AISD) minimum competency graduation requirements. The graduation competency status of all AISD students in grades 8 to 12 are documented. The report provides additional information on the data…

A Procedural Skills OSCE: Assessing Technical and Non-Technical Skills of Internal Medicine Residents

ERIC Educational Resources Information Center

Pugh, Debra; Hamstra, Stanley J.; Wood, Timothy J.; Humphrey-Murto, Susan; Touchie, Claire; Yudkowsky, Rachel; Bordage, Georges

2015-01-01

Internists are required to perform a number of procedures that require mastery of technical and non-technical skills, however, formal assessment of these skills is often lacking. The purpose of this study was to develop, implement, and gather validity evidence for a procedural skills objective structured clinical examination (PS-OSCE) for internal…

Setting Performance Standards for Technical and Nontechnical Competence in General Surgery.

PubMed

Szasz, Peter; Bonrath, Esther M; Louridas, Marisa; Fecso, Andras B; Howe, Brett; Fehr, Adam; Ott, Michael; Mack, Lloyd A; Harris, Kenneth A; Grantcharov, Teodor P

2017-07-01

The objectives of this study were to (1) create a technical and nontechnical performance standard for the laparoscopic cholecystectomy, (2) assess the classification accuracy and (3) credibility of these standards, (4) determine a trainees' ability to meet both standards concurrently, and (5) delineate factors that predict standard acquisition. Scores on performance assessments are difficult to interpret in the absence of established standards. Trained raters observed General Surgery residents performing laparoscopic cholecystectomies using the Objective Structured Assessment of Technical Skill (OSATS) and the Objective Structured Assessment of Non-Technical Skills (OSANTS) instruments, while as also providing a global competent/noncompetent decision for each performance. The global decision was used to divide the trainees into 2 contrasting groups and the OSATS or OSANTS scores were graphed per group to determine the performance standard. Parametric statistics were used to determine classification accuracy and concurrent standard acquisition, receiver operator characteristic (ROC) curves were used to delineate predictive factors. Thirty-six trainees were observed 101 times. The technical standard was an OSATS of 21.04/35.00 and the nontechnical standard an OSANTS of 22.49/35.00. Applying these standards, competent/noncompetent trainees could be discriminated in 94% of technical and 95% of nontechnical performances (P < 0.001). A 21% discordance between technically and nontechnically competent trainees was identified (P < 0.001). ROC analysis demonstrated case experience and trainee level were both able to predict achieving the standards with an area under the curve (AUC) between 0.83 and 0.96 (P < 0.001). The present study presents defensible standards for technical and nontechnical performance. Such standards are imperative to implementing summative assessments into surgical training.

16 CFR 1406.5 - Performance and technical data to be furnished to the Commission.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Commission the following performance and technical data related to performance and safety. (a) Written notice... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Performance and technical data to be... TECHNICAL DATA § 1406.5 Performance and technical data to be furnished to the Commission. Manufacturers...

77 FR 20406 - International Cooperation on Harmonisation of Technical Requirements for Registration of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-04

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2012-D-0288] International Cooperation on Harmonisation of Technical Requirements for Registration of Veterinary Medicinal... been developed for veterinary use by the International Cooperation on Harmonisation of Technical...

A procedural skills OSCE: assessing technical and non-technical skills of internal medicine residents.

PubMed

Pugh, Debra; Hamstra, Stanley J; Wood, Timothy J; Humphrey-Murto, Susan; Touchie, Claire; Yudkowsky, Rachel; Bordage, Georges

2015-03-01

Internists are required to perform a number of procedures that require mastery of technical and non-technical skills, however, formal assessment of these skills is often lacking. The purpose of this study was to develop, implement, and gather validity evidence for a procedural skills objective structured clinical examination (PS-OSCE) for internal medicine (IM) residents to assess their technical and non-technical skills when performing procedures. Thirty-five first to third-year IM residents participated in a 5-station PS-OSCE, which combined partial task models, standardized patients, and allied health professionals. Formal blueprinting was performed and content experts were used to develop the cases and rating instruments. Examiners underwent a frame-of-reference training session to prepare them for their rater role. Scores were compared by levels of training, experience, and to evaluation data from a non-procedural OSCE (IM-OSCE). Reliability was calculated using Generalizability analyses. Reliabilities for the technical and non-technical scores were 0.68 and 0.76, respectively. Third-year residents scored significantly higher than first-year residents on the technical (73.5 vs. 62.2%) and non-technical (83.2 vs. 75.1%) components of the PS-OSCE (p < 0.05). Residents who had performed the procedures more frequently scored higher on three of the five stations (p < 0.05). There was a moderate disattenuated correlation (r = 0.77) between the IM-OSCE and the technical component of the PS-OSCE scores. The PS-OSCE is a feasible method for assessing multiple competencies related to performing procedures and this study provides validity evidence to support its use as an in-training examination.

Regulatory Requirements and Technical Analysis for Department of Energy Regulated Performance Assessments of Shallow-Trench Disposal of Low-Level Radioactive Waste at the Nevada Test Site

NASA Astrophysics Data System (ADS)

Crowe, B.; Black, P.; Tauxe, J.; Yucel, V.; Rawlinson, S.; Colarusso, A.; DiSanza, F.

2001-12-01

The National Nuclear Security Administration, Nevada Operations Office (NNSA/NV) operates and maintains two active facilities on the Nevada Test Site (NTS) that dispose Department of Energy (DOE) defense-generated low-level radioactive (LLW), mixed radioactive, and classified waste in shallow trenches, pits and large-diameter boreholes. The operation and maintenance of the LLW disposal sites are self-regulated under DOE Order 435.1, which requires review of a Performance Assessment for four performance objectives: 1) all pathways 25 mrem/yr limit; 2) atmospheric pathways 10 mrem/yr limit; 3) radon flux density of 20 pCi/m2/s; and 4) groundwater resource protection (Safe Drinking Water Act; 4 mrem/yr limit). The inadvertent human intruder is protected under a dual 500- and 100-mrem limit (acute and chronic exposure). In response to the Defense Nuclear Facilities Safety Board Recommendation 92 2, a composite analysis is required that must examine all interacting sources for compliance against both 30 and 100 mrem/yr limits. A small component of classified transuranic waste is buried at intermediate depths in 3-meter diameter boreholes at the Area 5 LLW disposal facility and is assessed through DOE-agreement against the requirements of the Environmental Protection Agency (EPA)'s 40 CFR 191. The hazardous components of mixed LLW are assessed against RCRA requirements. The NTS LLW sites fall directly under three sets of federal regulations and the regulatory differences result not only in organizational challenges, but also in different decision objectives and technical paths to completion. The DOE regulations require deterministic analysis for a 1,000-year compliance assessment supplemented by probabilistic analysis under a long-term maintenance program. The EPA regulations for TRU waste are probabilistically based for a compliance interval of 10,000 years. Multiple steps in the assessments are strongly dependent on assumptions for long-term land use policies

47 CFR 25.214 - Technical requirements for space stations in the Satellite Digital Audio Radio Service and...

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 2 2014-10-01 2014-10-01 false Technical requirements for space stations in the Satellite Digital Audio Radio Service and associated terrestrial repeaters. 25.214 Section 25.214... Technical Standards § 25.214 Technical requirements for space stations in the Satellite Digital Audio Radio...

47 CFR 25.214 - Technical requirements for space stations in the satellite digital audio radio service and...

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 2 2012-10-01 2012-10-01 false Technical requirements for space stations in the satellite digital audio radio service and associated terrestrial repeaters. 25.214 Section 25.214... Technical Standards § 25.214 Technical requirements for space stations in the satellite digital audio radio...

47 CFR 25.214 - Technical requirements for space stations in the satellite digital audio radio service and...

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 2 2011-10-01 2011-10-01 false Technical requirements for space stations in the satellite digital audio radio service and associated terrestrial repeaters. 25.214 Section 25.214... Technical Standards § 25.214 Technical requirements for space stations in the satellite digital audio radio...

47 CFR 25.214 - Technical requirements for space stations in the Satellite Digital Audio Radio Service and...

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 2 2013-10-01 2013-10-01 false Technical requirements for space stations in the Satellite Digital Audio Radio Service and associated terrestrial repeaters. 25.214 Section 25.214... Technical Standards § 25.214 Technical requirements for space stations in the Satellite Digital Audio Radio...

47 CFR 25.214 - Technical requirements for space stations in the satellite digital audio radio service and...

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Technical requirements for space stations in the satellite digital audio radio service and associated terrestrial repeaters. 25.214 Section 25.214... Technical Standards § 25.214 Technical requirements for space stations in the satellite digital audio radio...

47 CFR 25.215 - Technical requirements for space stations in the Direct Broadcast Satellite Service.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 2 2012-10-01 2012-10-01 false Technical requirements for space stations in... Technical requirements for space stations in the Direct Broadcast Satellite Service. In addition to § 25.148(f), space station antennas operating in the Direct Broadcast Satellite Service must be designed to...

47 CFR 25.215 - Technical requirements for space stations in the Direct Broadcast Satellite Service.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 2 2013-10-01 2013-10-01 false Technical requirements for space stations in... Technical requirements for space stations in the Direct Broadcast Satellite Service. In addition to § 25.148(f), space station antennas operating in the Direct Broadcast Satellite Service must be designed to...

47 CFR 25.215 - Technical requirements for space stations in the Direct Broadcast Satellite Service.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 2 2011-10-01 2011-10-01 false Technical requirements for space stations in... Technical requirements for space stations in the Direct Broadcast Satellite Service. In addition to § 25.148(f), space station antennas operating in the Direct Broadcast Satellite Service must be designed to...

47 CFR 25.215 - Technical requirements for space stations in the Direct Broadcast Satellite Service.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Technical requirements for space stations in... Technical requirements for space stations in the Direct Broadcast Satellite Service. In addition to § 25.148(f), space station antennas operating in the Direct Broadcast Satellite Service must be designed to...

22 CFR 124.8 - Clauses required both in manufacturing license agreements and technical assistance agreements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... agreements and technical assistance agreements. 124.8 Section 124.8 Foreign Relations DEPARTMENT OF STATE... Clauses required both in manufacturing license agreements and technical assistance agreements. The following statements must be included both in manufacturing license agreements and in technical assistance...

Sortie laboratory, phase B technical summary. [design and operational requirements

NASA Technical Reports Server (NTRS)

1973-01-01

The design and operational requirements which evolved from Sortie Lab (SL) analysis are summarized. A source of requirements for systems is given along with experimental support for the SL, baseline. Basic design data covered include: configuration definition, mission analysis, experimental integration, safety, and logistics. A technical summary outlines characteristics which reflect the influence of the growth in SL capability and the results of the mission and operational analysis. Each of the selected areas is described in terms of objectives, equipment, operational concept, and support requirements.

Vehicle Integrated Performance Analysis, the VIPA Experience: Reconnecting with Technical Integration

NASA Technical Reports Server (NTRS)

McGhee, David S.

2005-01-01

Today's NASA is facing significant challenges and changes. The Exploration initiative indicates a large increase in projects with limited increase in budget. The Columbia report has criticized NASA for its lack of insight and technical integration impacting its ability to provide safety. The Aldridge report is advocating NASA find new ways of doing business. Very early in the Space Launch Initiative (SLI) program a small team of engineers at MSFC were asked to propose a process for performing a system level assessment of a launch vehicle. The request was aimed primarily at providing insight and making NASA a "smart buyer." Out of this effort the VIPA team was created. The difference between the VIPA effort and many integration attempts is that VIPA focuses on using experienced people from various disciplines and a process which focuses them on a technically integrated assessment. Most previous attempts have focused on developing an all encompassing software tool. In addition, VIPA anchored its process formulation in the experience of its members and in early developmental Space Shuttle experience. The primary reference for this is NASA-TP-2001-210092, "Launch Vehicle Design Process: Characterization, Technical Integration, and Lessons Learned," and discussions with its authors. The foundations of VIPA's process are described. The VIPA team also recognized the need to drive detailed analysis earlier in the design process. Analyses and techniques typically done in later design phases, are brought forward using improved computing technology. The intent is to allow the identification of significant sensitivities, trades, and design issues much earlier in the program. This process is driven by the T-model for Technical Integration described in the aforementioned reference. VIPA's approach to performing system level technical integration is discussed in detail. Proposed definitions are offered to clarify this discussion and the general systems integration dialog. VIPA

Intraoperative adverse events can be compensated by technical performance in neonates and infants after cardiac surgery: a prospective study.

PubMed

Nathan, Meena; Karamichalis, John M; Liu, Hua; del Nido, Pedro; Pigula, Frank; Thiagarajan, Ravi; Bacha, Emile A

2011-11-01

Our objective was to define the relationship between surgical technical performance score, intraoperative adverse events, and major postoperative adverse events in complex pediatric cardiac repairs. Infants younger than 6 months were prospectively followed up until discharge from the hospital. Technical performance scores were graded as optimal, adequate, or inadequate based on discharge echocardiograms and need for reintervention after initial surgery. Case complexity was determined by Risk Adjustment in Congenital Heart Surgery (RACHS-1) category, and preoperative illness severity was assessed by Pediatric Risk of Mortality (PRISM) III score. Intraoperative adverse events were prospectively monitored. Outcomes were analyzed using nonparametric methods and a logistic regression model. A total of 166 patients (RACHS 4-6 [49%]), neonates [50%]) were observed. Sixty-one (37%) had at least 1 intraoperative adverse event, and 47 (28.3%) had at least 1 major postoperative adverse event. There was no correlation between intraoperative adverse events and RACHS, preoperative PRISM III, technical performance score, or postoperative adverse events on multivariate analysis. For the entire cohort, better technical performance score resulted in lower postoperative adverse events, lower postoperative PRISM, and lower length of stay and ventilation time (P < .001). Patients requiring intraoperative revisions fared as well as patients without, provided the technical score was at least adequate. In neonatal and infant open heart repairs, technical performance score is one of the main predictors of postoperative morbidity. Outcomes are not affected by intraoperative adverse events, including surgical revisions, provided technical performance score is at least adequate. Copyright © 2011 The American Association for Thoracic Surgery. Published by Mosby, Inc. All rights reserved.

16 CFR § 1407.3 - Providing performance and technical data to purchasers by labeling.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 16 Commercial Practices 2 2013-01-01 2013-01-01 false Providing performance and technical data to... TECHNICAL DATA BY LABELING § 1407.3 Providing performance and technical data to purchasers by labeling. (a... technical data related to performance and safety to prospective purchasers of such products at the time of...

The Future Cybersecurity Workforce: Going Beyond Technical Skills for Successful Cyber Performance

PubMed Central

Dawson, Jessica; Thomson, Robert

2018-01-01

One of the challenges in writing an article reviewing the current state of cyber education and workforce development is that there is a paucity of quantitative assessment regarding the cognitive aptitudes, work roles, or team organization required by cybersecurity professionals to be successful. In this review, we argue that the people who operate within the cyber domain need a combination of technical skills, domain specific knowledge, and social intelligence to be successful. They, like the networks they operate, must also be reliable, trustworthy, and resilient. Defining the knowledge, skills, attributes, and other characteristics is not as simple as defining a group of technical skills that people can be trained on; the complexity of the cyber domain makes this a unique challenge. There has been little research devoted to exactly what attributes individuals in the cyber domain need. What research does exist places an emphasis on technical and engineering skills while discounting the important social and organizational influences that dictate success or failure in everyday settings. This paper reviews the literature on cyber expertise and cyber workforce development to identify gaps and then argues for the important contribution of social fit in the highly complex and heterogenous cyber workforce. We then identify six assumptions for the future of cybersecurity workforce development, including the requirement for systemic thinkers, team players, a love for continued learning, strong communication ability, a sense of civic duty, and a blend of technical and social skill. Finally, we make recommendations for social and cognitive metrics which may be indicative of future performance in cyber work roles to provide a roadmap for future scholars. PMID:29946276

The Future Cybersecurity Workforce: Going Beyond Technical Skills for Successful Cyber Performance.

PubMed

Dawson, Jessica; Thomson, Robert

2018-01-01

One of the challenges in writing an article reviewing the current state of cyber education and workforce development is that there is a paucity of quantitative assessment regarding the cognitive aptitudes, work roles, or team organization required by cybersecurity professionals to be successful. In this review, we argue that the people who operate within the cyber domain need a combination of technical skills, domain specific knowledge, and social intelligence to be successful. They, like the networks they operate, must also be reliable, trustworthy, and resilient. Defining the knowledge, skills, attributes, and other characteristics is not as simple as defining a group of technical skills that people can be trained on; the complexity of the cyber domain makes this a unique challenge. There has been little research devoted to exactly what attributes individuals in the cyber domain need. What research does exist places an emphasis on technical and engineering skills while discounting the important social and organizational influences that dictate success or failure in everyday settings. This paper reviews the literature on cyber expertise and cyber workforce development to identify gaps and then argues for the important contribution of social fit in the highly complex and heterogenous cyber workforce. We then identify six assumptions for the future of cybersecurity workforce development, including the requirement for systemic thinkers, team players, a love for continued learning, strong communication ability, a sense of civic duty, and a blend of technical and social skill. Finally, we make recommendations for social and cognitive metrics which may be indicative of future performance in cyber work roles to provide a roadmap for future scholars.

Learning curves for transapical transcatheter aortic valve replacement in the PARTNER-I trial: Technical performance, success, and safety.

PubMed

Suri, Rakesh M; Minha, Sa'ar; Alli, Oluseun; Waksman, Ron; Rihal, Charanjit S; Satler, Lowell P; Greason, Kevin L; Torguson, Rebecca; Pichard, Augusto D; Mack, Michael; Svensson, Lars G; Rajeswaran, Jeevanantham; Lowry, Ashley M; Ehrlinger, John; Mick, Stephanie L; Tuzcu, E Murat; Thourani, Vinod H; Makkar, Raj; Holmes, David; Leon, Martin B; Blackstone, Eugene H

2016-09-01

Introduction of hybrid techniques, such as transapical transcatheter aortic valve replacement (TA-TAVR), requires skills that a heart team must master to achieve technical efficiency: the technical performance learning curve. To date, the learning curve for TA-TAVR remains unknown. We therefore evaluated the rate at which technical performance improved, assessed change in occurrence of adverse events in relation to technical performance, and determined whether adverse events after TA-TAVR were linked to acquiring technical performance efficiency (the learning curve). From April 2007 to February 2012, 1100 patients, average age 85.0 ± 6.4 years, underwent TA-TAVR in the PARTNER-I trial. Learning curves were defined by institution-specific patient sequence number using nonlinear mixed modeling. Mean procedure time decreased from 131 to 116 minutes within 30 cases (P = .06) and device success increased to 90% by case 45 (P = .0007). Within 30 days, 354 patients experienced a major adverse event (stroke in 29, death in 96), with possibly decreased complications over time (P ∼ .08). Although longer procedure time was associated with more adverse events (P < .0001), these events were associated with change in patient risk profile, not the technical performance learning curve (P = .8). The learning curve for TA-TAVR was 30 to 45 procedures performed, and technical efficiency was achieved without compromising patient safety. Although fewer patients are now undergoing TAVR via nontransfemoral access, understanding TA-TAVR learning curves and their relationship with outcomes is important as the field moves toward next-generation devices, such as those to replace the mitral valve, delivered via the left ventricular apex. Copyright © 2016 The American Association for Thoracic Surgery. Published by Elsevier Inc. All rights reserved.

Wind/tornado design criteria, development to achieve required probabilistic performance goals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ng, D.S.

1991-06-01

This paper describes the strategy for developing new design criteria for a critical facility to withstand loading induced by the wind/tornado hazard. The proposed design requirements for resisting wind/tornado loads are based on probabilistic performance goals. The proposed design criteria were prepared by a Working Group consisting of six experts in wind/tornado engineering and meteorology. Utilizing their best technical knowledge and judgment in the wind/tornado field, they met and discussed the methodologies and reviewed available data. A review of the available wind/tornado hazard model for the site, structural response evaluation methods, and conservative acceptance criteria lead to proposed design criteriamore » that has a high probability of achieving the required performance goals.« less

Wind/tornado design criteria, development to achieve required probabilistic performance goals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ng, D.S.

This paper describes the strategy for developing new design criteria for a critical facility to withstand loading induced by the wind/tornado hazard. The proposed design requirements for resisting wind/tornado loads are based on probabilistic performance goals. The proposed design criteria were prepared by a Working Group consisting of six experts in wind/tornado engineering and meteorology. Utilizing their best technical knowledge and judgment in the wind/tornado field, they met and discussed the methodologies and reviewed available data. A review of the available wind/tornado hazard model for the site, structural response evaluation methods, and conservative acceptance criteria lead to proposed design criteriamore » that has a high probability of achieving the required performance goals.« less

Robotic acquisition programs: technical and performance challenges

NASA Astrophysics Data System (ADS)

Thibadoux, Steven A.

2002-07-01

The Unmanned Ground Vehicles/ Systems Joint Project Office (UGV/S JPO) is developing and fielding a variety of tactical robotic systems for the Army and Marine Corps. The Standardized Robotic System (SRS) provides a family of common components that can be installed in existing military vehicles, to allow unmanned operation of the vehicle and its payloads. The Robotic Combat Support System (RCSS) will be a medium sized unmanned system with interchangeable attachments, allowing a remote operator to perform a variety of engineering tasks. The Gladiator Program is a USMC initiative for a small to medium sized, highly mobile UGV to conduct scout/ surveillance missions and to carry various lethal and non-lethal payloads. Acquisition plans for these programs require preplanned evolutionary block upgrades to add operational capability, as new technology becomes available. This paper discusses technical and performance issues that must be resolved and the enabling technologies needed for near term block upgrades of these first generation robotic systems. Additionally, two Joint Robotics Program (JRP) initiatives, Robotic Acquisition through Virtual Environments and Networked Simulations (RAVENS) and Joint Architecture for Unmanned Ground Systems (JAUGS), will be discussed. RAVENS and JAUGS will be used to efficiently evaluate and integrate new technologies to be incorporated in system upgrades.

Is the technical performance of young soccer players influenced by hormonal status, sexual maturity, anthropometric profile, and physical performance?

PubMed

Moreira, Alexandre; Massa, Marcelo; Thiengo, Carlos R; Rodrigues Lopes, Rafael Alan; Lima, Marcelo R; Vaeyens, Roel; Barbosa, Wesley P; Aoki, Marcelo S

2017-12-01

The aim of this study was to examine the influence of hormonal status, anthropometric profile, sexual maturity level, and physical performance on the technical abilities of 40 young male soccer players during small-sided games (SSGs). Anthropometric profiling, saliva sampling, sexual maturity assessment (Tanner scale), and physical performance tests (Yo-Yo and vertical jumps) were conducted two weeks prior to the SSGs. Salivary testosterone was determined by the enzyme-linked immunosorbent assay method. Technical performance was determined by the frequency of actions during SSGs. Principal component analyses identified four technical actions of importance: total number of passes, effectiveness, goal attempts, and total tackles. A multivariate canonical correlation analysis was then employed to verify the prediction of a multiple dependent variables set (composed of four technical actions) from an independent set of variables, composed of testosterone concentration, stage of pubic hair and genitalia development, vertical jumps and Yo-Yo performance. A moderate-to-large relationship between the technical performance set and the independent set was observed. The canonical correlation was 0.75 with a canonical R 2 of 0.45. The highest structure coefficient in the technical performance set was observed for tackles (0.77), while testosterone presented the highest structure coefficient (0.75) for the variables of the independent set. The current data suggest that the selected independent set of variables might be useful in predicting SSG performance in young soccer players. Coaches should be aware that physical development plays a key role in technical performance to avoid decision-making mistakes during the selection of young players.

The impact of nontechnical skills on technical performance in surgery: a systematic review.

PubMed

Hull, Louise; Arora, Sonal; Aggarwal, Rajesh; Darzi, Ara; Vincent, Charles; Sevdalis, Nick

2012-02-01

Failures in nontechnical and teamwork skills frequently lie at the heart of harm and near-misses in the operating room (OR). The purpose of this systematic review was to assess the impact of nontechnical skills on technical performance in surgery. MEDLINE, EMBASE, PsycINFO databases were searched, and 2,041 articles were identified. After limits were applied, 341 articles were retrieved for evaluation. Of these, 28 articles were accepted for this review. Data were extracted from the articles regarding sample population, study design and setting, measures of nontechnical skills and technical performance, study findings, and limitations. Of the 28 articles that met inclusion criteria, 21 articles assessed the impact of surgeons' nontechnical skills on their technical performance. The evidence suggests that receiving feedback and effectively coping with stressful events in the OR has a beneficial impact on certain aspects of technical performance. Conversely, increased levels of fatigue are associated with detriments to surgical skill. One article assessed the impact of anesthesiologists' nontechnical skills on anesthetic technical performance, finding a strong positive correlation between the 2 skill sets. Finally, 6 articles assessed the impact of multiple nontechnical skills of the entire OR team on surgical performance. A strong relationship between teamwork failure and technical error was empirically demonstrated in these studies. Evidence suggests that certain nontechnical aspects of performance can enhance or, if lacking, contribute to deterioration of surgeons' technical performance. The precise extent of this effect remains to be elucidated. Copyright © 2012 American College of Surgeons. Published by Elsevier Inc. All rights reserved.

Spatial abilities and technical skills performance in health care: a systematic review.

PubMed

Langlois, Jean; Bellemare, Christian; Toulouse, Josée; Wells, George A

2015-11-01

The aim of this study was to conduct a systematic review and meta-analysis of the relationship between spatial abilities and technical skills performance in health care in beginners and to compare this relationship with those in intermediate and autonomous learners. Search criteria included 'spatial abilities' and 'technical skills'. Keywords related to these criteria were defined. A literature search was conducted to 20 December, 2013 in Scopus (including MEDLINE) and in several databases on EBSCOhost platforms (CINAHL Plus with Full Text, ERIC, Education Source and PsycINFO). Citations were obtained and reviewed by two independent reviewers. Articles related to retained citations were reviewed and a final list of eligible articles was determined. Articles were assessed for quality using the Scottish Intercollegiate Guidelines Network-50 assessment instrument. Data were extracted from articles in a systematic way. Correlations between spatial abilities test scores and technical skills performance were identified. A series of 8289 citations was obtained. Eighty articles were retained and fully reviewed, yielding 36 eligible articles. The systematic review found a tendency for spatial abilities to be negatively correlated with the duration of technical skills and positively correlated with the quality of technical skills performance in beginners and intermediate learners. Pooled correlations of studies were -0.46 (p = 0.03) and -0.38 (95% confidence interval [CI] -0.53 to -0.21) for duration and 0.33 (95% CI 0.20-0.44) and 0.41 (95% CI 0.26-0.54) for quality of technical skills performance in beginners and intermediate learners, respectively. However, correlations between spatial abilities test scores and technical skills performance were not statistically significant in autonomous learners. Spatial abilities are an important factor to consider in selecting and training individuals in technical skills in health care. © 2015 John Wiley & Sons Ltd.

A Comparison of Physical and Technical Performance Profiles Between Successful and Less-Successful Professional Rugby League Teams.

PubMed

Kempton, Thomas; Sirotic, Anita C; Coutts, Aaron J

2017-04-01

To examine differences in physical and technical performance profiles using a large sample of match observations drawn from successful and less-successful professional rugby league teams. Match activity profiles were collected using global positioning satellite (GPS) technology from 29 players from a successful rugby league team during 24 games and 25 players from a less-successful team during 18 games throughout 2 separate competition seasons. Technical performance data were obtained from a commercial statistics provider. A progressive magnitude-based statistical approach was used to compare differences in physical and technical performance variables between the reference teams. There were no clear differences in playing time, absolute and relative total distances, or low-speed running distances between successful and less-successful teams. The successful team possibly to very likely had lower higher-speed running demands and likely had fewer physical collisions than the less-successful team, although they likely to most likely demonstrated more accelerations and decelerations and likely had higher average metabolic power. The successful team very likely gained more territory in attack, very likely had more possessions, and likely committed fewer errors. In contrast, the less-successful team was likely required to attempt more tackles, most likely missed more tackles, and very likely had a lower effective tackle percentage. In the current study, successful match performance was not contingent on higher match running outputs or more physical collisions; rather, proficiency in technical performance components better differentiated successful and less-successful teams.

Replacing fossil based plastic performance products by bio-based plastic products-Technical feasibility.

PubMed

van den Oever, Martien; Molenveld, Karin

2017-07-25

Larger scale market introduction of new bio-based products requires a clear advantage regarding sustainability, as well as an adequate techno-economic positioning relative to fossil based products. In a previous paper [Broeren et al., 2016], LCA results per kg and per functionality equivalent of bio-based plastics were presented, together with economic considerations. The present paper discusses the mechanical and thermal properties of a range of commercially available bio-based plastics based on polylactic acid (PLA), cellulose esters, starch and polyamides, and the feasibility of replacing fossil-based counterparts based on performance. The evaluation is approached from an end user perspective. First, potentially suitable bio-based plastics are selected based on manufacturers' specifications in technical data sheets, then a first experimental evaluation is performed on injection moulded ISO specimens, and finally a further selection of plastics is tested on large 50×70cm panels. This technical feasibility study indicates that so far bio-based plastics do not completely match the properties of high performance materials like flame retardant V-0 PC/ABS blends used in electronic devices. The performance gap is being decreased by the development of stereocomplex PLA and hybrid PLA blends with polycarbonate, which offer clearly improved properties with respect to maximum usage temperature and toughness. In addition, several materials meet the V-0 flammability requirements needed in specific durable applications. On the other hand, improving these properties so far has negative consequences for the bio-based content. This study also shows that replacement of bulk polymers like PS is feasible using PLA compounds with a bio-based content as high as 85%. Copyright © 2016 Elsevier B.V. All rights reserved.

Technical match characteristics and influence of body anthropometry on playing performance in male elite team handball.

PubMed

Michalsik, Lars Bojsen; Madsen, Klavs; Aagaard, Per

2015-02-01

Modern team handball match-play imposes substantial physical and technical demands on elite players. However, only limited knowledge seems to exist about the specific working requirements in elite team handball. Thus, the purpose of this study was to examine the physical demands imposed on male elite team handball players in relation to playing position and body anthropometry. Based on continuous video recording of individual players during elite team handball match-play (62 tournament games, ∼4 players per game), computerized technical match analysis was performed in male elite team handball players along with anthropometric measurements over a 6 season time span. Technical match activities were distributed in 6 major types of playing actions (shots, breakthroughs, fast breaks, tackles, technical errors, and defense errors) and further divided into various subcategories (e.g., hard or light tackles, type of shot, claspings, screenings, and blockings). Players showed 36.9 ± 13.1 (group mean ± SD) high-intense technical playing actions per match with a mean total effective playing time of 53.85 ± 5.87 minutes. In offense, each player performed 6.0 ± 5.2 fast breaks, received 34.5 ± 21.3 tackles in total, and performed in defense 3.7 ± 3.5 blockings, 3.9 ± 3.0 claspings, and 5.8 ± 3.6 hard tackles. Wing players (84.5 ± 5.8 kg, 184.9 ± 5.7 cm) were less heavy and smaller (p < 0.001) than backcourt players (94.7 ± 7.1 kg, 191.9 ± 5.4 cm) and pivots (99.4 ± 6.2 kg, 194.8 ± 3.6 cm). In conclusion, modern male elite team handball match-play is characterized by a high number of short-term, high-intense intermittent technical playing actions. Indications of technical fatigue were observed. Physical demands differed between playing positions with wing players performing more fast breaks and less physical confrontations with opponent players than backcourt players and pivots. Body anthropometry seemed to have an important influence on playing performance

10 CFR 63.114 - Requirements for performance assessment.

Code of Federal Regulations, 2014 CFR

2014-01-01

... GEOLOGIC REPOSITORY AT YUCCA MOUNTAIN, NEVADA Technical Criteria Postclosure Performance Assessment § 63..., hydrology, and geochemistry (including disruptive processes and events) of the Yucca Mountain site, and the... disposal, and provide for the technical basis for parameter ranges, probability distributions, or bounding...

10 CFR 63.114 - Requirements for performance assessment.

Code of Federal Regulations, 2013 CFR

2013-01-01

... GEOLOGIC REPOSITORY AT YUCCA MOUNTAIN, NEVADA Technical Criteria Postclosure Performance Assessment § 63..., hydrology, and geochemistry (including disruptive processes and events) of the Yucca Mountain site, and the... disposal, and provide for the technical basis for parameter ranges, probability distributions, or bounding...

10 CFR 63.114 - Requirements for performance assessment.

Code of Federal Regulations, 2012 CFR

2012-01-01

... GEOLOGIC REPOSITORY AT YUCCA MOUNTAIN, NEVADA Technical Criteria Postclosure Performance Assessment § 63..., hydrology, and geochemistry (including disruptive processes and events) of the Yucca Mountain site, and the... disposal, and provide for the technical basis for parameter ranges, probability distributions, or bounding...

10 CFR 63.114 - Requirements for performance assessment.

Code of Federal Regulations, 2011 CFR

2011-01-01

... GEOLOGIC REPOSITORY AT YUCCA MOUNTAIN, NEVADA Technical Criteria Postclosure Performance Assessment § 63..., hydrology, and geochemistry (including disruptive processes and events) of the Yucca Mountain site, and the... disposal, and provide for the technical basis for parameter ranges, probability distributions, or bounding...

10 CFR 63.114 - Requirements for performance assessment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... GEOLOGIC REPOSITORY AT YUCCA MOUNTAIN, NEVADA Technical Criteria Postclosure Performance Assessment § 63..., hydrology, and geochemistry (including disruptive processes and events) of the Yucca Mountain site, and the... disposal, and provide for the technical basis for parameter ranges, probability distributions, or bounding...

Do technical skills correlate with non-technical skills in crisis resource management: a simulation study.

PubMed

Riem, N; Boet, S; Bould, M D; Tavares, W; Naik, V N

2012-11-01

Both technical skills (TS) and non-technical skills (NTS) are key to ensuring patient safety in acute care practice and effective crisis management. These skills are often taught and assessed separately. We hypothesized that TS and NTS are not independent of each other, and we aimed to evaluate the relationship between TS and NTS during a simulated intraoperative crisis scenario. This study was a retrospective analysis of performances from a previously published work. After institutional ethics approval, 50 anaesthesiology residents managed a simulated crisis scenario of an intraoperative cardiac arrest secondary to a malignant arrhythmia. We used a modified Delphi approach to design a TS checklist, specific for the management of a malignant arrhythmia requiring defibrillation. All scenarios were recorded. Each performance was analysed by four independent experts. For each performance, two experts independently rated the technical performance using the TS checklist, and two other experts independently rated NTS using the Anaesthetists' Non-Technical Skills score. TS and NTS were significantly correlated to each other (r=0.45, P<0.05). During a simulated 5 min resuscitation requiring crisis resource management, our results indicate that TS and NTS are related to one another. This research provides the basis for future studies evaluating the nature of this relationship, the influence of NTS training on the performance of TS, and to determine whether NTS are generic and transferrable between crises that require different TS.

The use of a checklist improves anaesthesiologists' technical and non-technical performance for simulated malignant hyperthermia management.

PubMed

Hardy, Jean-Baptiste; Gouin, Antoine; Damm, Cédric; Compère, Vincent; Veber, Benoît; Dureuil, Bertrand

2018-02-01

Anaesthesiologists may occasionally manage life-threatening operating room (OR) emergencies. Managing OR emergencies implies real-time analysis of often complicated situations, prompt medical knowledge retrieval, coordinated teamwork and effective decision making in stressful settings. Checklists are recommended to improve performance and reduce the risk of medical errors. This study aimed to assess the usefulness of the French Society of Anaesthesia and Intensive Care's (SFAR) "Malignant Hyperthermia" (MH) checklist on a simulated episode of MH crisis and management thereof by registered anesthesiologists. Twenty-four anaesthesiologists were allocated to 2 groups (checklist and control). Their technical performance in adherence with the SFAR guidelines was assessed by a 30-point score and their non-technical performance was assessed by the Anaesthetists' Non-Technical Skills (ANTS) score. Every task completion was assessed independently. Data are shown as median (first-third quartiles). Anaesthesiologists in the checklist group had higher technical performance scores (24/30 (21.5-25) vs 18/30 (15.5-19.5), P=0.002) and ANTS scores (56.5/60 (47.5-58) vs 48.5/60 (41-50.5), P=0.024). They administered the complete initial dose of dantrolene (2mg/kg) more quickly (15.7 minutes [13.9-18.3] vs 22.4 minutes [18.6-25]) than the control group (P=0.017). However, anaesthesiologists deemed the usability of the checklist to be perfectible. Registered anaesthesiologists' use of the MH checklist during a simulation session widely improved their adherence to guidelines and non-technical skills. This study strongly suggests the benefit of checklist tools for emergency management. Notwithstanding, better awareness and training for anaesthesiologists could further improve the use of this tool. Copyright © 2017 Société française d'anesthésie et de réanimation (Sfar). Published by Elsevier Masson SAS. All rights reserved.

Factors that influence the non-technical skills performance of scrub nurses: a prospective study.

PubMed

Kang, Evelyn; Massey, Debbie; Gillespie, Brigid M

2015-12-01

To identify and describe the factors that impact on the performance of scrub nurses' non-technical skills performance during the intra-operative phase of surgery. Non-technical skills have been identified as important precursors to errors in the operating room. However, few studies have investigated factors influencing non-technical skills of scrub nurses. Prospective observational study. Structured observations were performed on a sample of 182 surgical procedures across eight specialities by two trained observers from August 2012-April 2013 at two hospital sites. Participants were purposively selected scrub nurses. Bivariate correlations and a multiple linear regression model were used to identify associations among length of surgery, patients' acuity using the American Society of Anesthesiologists classification system, team familiarity, number of occasions scout nurses leave the operating room, change of scout nurse and the outcome, the non-technical skills performance of scrub nurses. Patient acuity and team familiarity were the strongest predictors of scrub nurses' non-technical skills performance at hospital site A. There were no correlations between the predictors and the performance of scrub nurses at hospital site B. A dedicated surgical team and patient acuity potentially influence the performance of scrub nurses' non-technical skills. Familiarity with team members foster advanced planning, thus minimizing distractions and interruptions that impact on scrub nurses' performance. Development of interventions aimed at improving non-technical skills has the potential to make a substantial difference and enhance patient care. © 2015 John Wiley & Sons Ltd.

The Effect of Technical Performance on Patient Outcomes in Surgery: A Systematic Review.

PubMed

Fecso, Andras B; Szasz, Peter; Kerezov, Georgi; Grantcharov, Teodor P

2017-03-01

Systematic review of the effect of intraoperative technical performance on patient outcomes. The operating room is a high-stakes, high-risk environment. As a result, the quality of surgical interventions affecting patient outcomes has been the subject of discussion and research for years. MEDLINE, EMBASE, PsycINFO, and Cochrane databases were searched. All surgical specialties were eligible for inclusion. Data were reviewed in regards to the methods by which technical performance was measured, what patient outcomes were assessed, and how intraoperative technical performance affected patient outcomes. Quality of evidence was assessed using the Medical Education Research Study Quality Instrument (MERSQI). Of the 12,758 studies initially identified, 24 articles (7775 total participants) were ultimately included in this review. Seventeen studies assessed the performance of the faculty alone, 2 assessed both the faculty and trainees, 1 assessed trainees alone, and in 4 studies, the level of the operating surgeon was not specified. In 18 studies, a performance assessment tool was used. Patient outcomes were evaluated using intraoperative complications, short-term morbidity, long-term morbidity, short-term mortality, and long-term mortality. The average MERSQI score was 11.67 (range 9.5-14.5). Twenty-one studies demonstrated that superior technical performance was related to improved patient outcomes. The results of this systematic review demonstrated that superior technical performance positively affects patient outcomes. Despite this initial evidence, more robust research is needed to directly assess intraoperative technical performance and its effect on postoperative patient outcomes using meaningful assessment instruments and reliable processes.

English Skills for Engineers Required by the English Technical Writing Test

NASA Astrophysics Data System (ADS)

Kyouno, Noboru

Japanese English education has focused mainly on teaching passive skills such as reading and listening, whereas actual business activities in society require active skills such as writing and speaking in addition to the passive skills. This educational situation is estimated to be a reason Japanese engineers are less confident in writing and speaking than in reading and listening. This paper focuses on details of the English Technical Writing Test provided by the Japan Society of Technical Communication and emphasizes the importance of the active skills, mainly focusing on what skills should be taught in the future and how to develop these skills. This paper also stresses the necessity of learning rhetoric-related skills, concept of information words, as well as paragraph reading and writing skills based on the concept of the 3Cs (Correct, Clear, and Concise) as a means to develop technical writing skills for engineers.

76 FR 35103 - Training and Qualification Requirements for Check Airmen and Flight Instructors; Technical Amendment

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-16

... which initial and transition flight training must include an in-flight element. Technical Amendment This.... 28471; Amendment Nos. 121-355 and 135-125] RIN 2120-AF08 Training and Qualification Requirements for Check Airmen and Flight Instructors; Technical Amendment AGENCY: Federal Aviation Administration (FAA...

48 CFR 3419.870 - Acquisition of technical requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... competition to submit written technical proposals. Otherwise, ED holds oral discussions with the participating... participating in a limited technical competition based on the written technical proposals or oral discussions... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Acquisition of technical...

Performance of technical trading rules: evidence from Southeast Asian stock markets.

PubMed

Tharavanij, Piyapas; Siraprapasiri, Vasan; Rajchamaha, Kittichai

2015-01-01

This paper examines the profitability of technical trading rules in the five Southeast Asian stock markets. The data cover a period of 14 years from January 2000 to December 2013. The instruments investigated are five Southeast Asian stock market indices: SET index (Thailand), FTSE Bursa Malaysia KLC index (Malaysia), FTSE Straits Times index (Singapore), JSX Composite index (Indonesia), and PSE composite index (the Philippines). Trading strategies investigated include Relative Strength Index, Stochastic oscillator, Moving Average Convergence-Divergence, Directional Movement Indicator and On Balance Volume. Performances are compared to a simple Buy-and-Hold. Statistical tests are also performed. Our empirical results show a strong performance of technical trading rules in an emerging stock market of Thailand but not in a more mature stock market of Singapore. The technical trading rules also generate statistical significant returns in the Malaysian, Indonesian and the Philippine markets. However, after taking transaction costs into account, most technical trading rules do not generate net returns. This fact suggests different levels of market efficiency among Southeast Asian stock markets. This paper finds three new insights. Firstly, technical indicators does not help much in terms of market timing. Basically, traders cannot expect to buy at a relative low price and sell at a relative high price by just using technical trading rules. Secondly, technical trading rules can be beneficial to individual investors as they help them to counter the behavioral bias called disposition effects which is the tendency to sell winning stocks too soon and holding on to losing stocks too long. Thirdly, even profitable strategies could not reliably predict subsequent market directions. They make money from having a higher average profit from profitable trades than an average loss from unprofitable ones.

47 CFR 80.271 - Technical requirements for portable survival craft radiotelephone transceivers.

Code of Federal Regulations, 2010 CFR

2010-10-01

... craft radiotelephone transceivers. 80.271 Section 80.271 Telecommunication FEDERAL COMMUNICATIONS... Authorization for Compulsory Ships § 80.271 Technical requirements for portable survival craft radiotelephone transceivers. (a) Portable survival craft radiotelephone transceivers must comply with the following: (1) The...

Technical Communication Internship Requirements in the Academic Economy: How We Compare among Ourselves and across Other Applied Fields

ERIC Educational Resources Information Center

Savage, Gerald J.; Seible, Marcea K.

2010-01-01

This article reports a study of internship requirements in technical communication programs compared with three established professions and one emerging profession that have certification or licensing requirements for practitioners. The study addresses three questions about technical communication internship programs: 1) Are internships offered as…

10 CFR 35.647 - Additional technical requirements for mobile remote afterloader units.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 1 2013-01-01 2013-01-01 false Additional technical requirements for mobile remote afterloader units. 35.647 Section 35.647 Energy NUCLEAR REGULATORY COMMISSION MEDICAL USE OF BYPRODUCT MATERIAL Photon Emitting Remote Afterloader Units, Teletherapy Units, and Gamma Stereotactic Radiosurgery...

10 CFR 35.647 - Additional technical requirements for mobile remote afterloader units.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 1 2014-01-01 2014-01-01 false Additional technical requirements for mobile remote afterloader units. 35.647 Section 35.647 Energy NUCLEAR REGULATORY COMMISSION MEDICAL USE OF BYPRODUCT MATERIAL Photon Emitting Remote Afterloader Units, Teletherapy Units, and Gamma Stereotactic Radiosurgery...

10 CFR 35.647 - Additional technical requirements for mobile remote afterloader units.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 1 2012-01-01 2012-01-01 false Additional technical requirements for mobile remote afterloader units. 35.647 Section 35.647 Energy NUCLEAR REGULATORY COMMISSION MEDICAL USE OF BYPRODUCT MATERIAL Photon Emitting Remote Afterloader Units, Teletherapy Units, and Gamma Stereotactic Radiosurgery...

10 CFR 35.647 - Additional technical requirements for mobile remote afterloader units.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 1 2011-01-01 2011-01-01 false Additional technical requirements for mobile remote afterloader units. 35.647 Section 35.647 Energy NUCLEAR REGULATORY COMMISSION MEDICAL USE OF BYPRODUCT MATERIAL Photon Emitting Remote Afterloader Units, Teletherapy Units, and Gamma Stereotactic Radiosurgery...

Assessing Technical Performance and Determining the Learning Curve in Cleft Palate Surgery Using a High-Fidelity Cleft Palate Simulator.

PubMed

Podolsky, Dale J; Fisher, David M; Wong Riff, Karen W; Szasz, Peter; Looi, Thomas; Drake, James M; Forrest, Christopher R

2018-06-01

This study assessed technical performance in cleft palate repair using a newly developed assessment tool and high-fidelity cleft palate simulator through a longitudinal simulation training exercise. Three residents performed five and one resident performed nine consecutive endoscopically recorded cleft palate repairs using a cleft palate simulator. Two fellows in pediatric plastic surgery and two expert cleft surgeons also performed recorded simulated repairs. The Cleft Palate Objective Structured Assessment of Technical Skill (CLOSATS) and end-product scales were developed to assess performance. Two blinded cleft surgeons assessed the recordings and the final repairs using the CLOSATS, end-product scale, and a previously developed global rating scale. The average procedure-specific (CLOSATS), global rating, and end-product scores increased logarithmically after each successive simulation session for the residents. Reliability of the CLOSATS (average item intraclass correlation coefficient (ICC), 0.85 ± 0.093) and global ratings (average item ICC, 0.91 ± 0.02) among the raters was high. Reliability of the end-product assessments was lower (average item ICC, 0.66 ± 0.15). Standard setting linear regression using an overall cutoff score of 7 of 10 corresponded to a pass score for the CLOSATS and the global score of 44 (maximum, 60) and 23 (maximum, 30), respectively. Using logarithmic best-fit curves, 6.3 simulation sessions are required to reach the minimum standard. A high-fidelity cleft palate simulator has been developed that improves technical performance in cleft palate repair. The simulator and technical assessment scores can be used to determine performance before operating on patients.

Technical evaluation of RETS-required reports for Browns Ferry Nuclear Power Station, Units 1, 2, and 3, for 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Young, T.E.; Magleby, E.H.

1985-09-06

A review was performed of reports required by federal regulations and the plant-specific radiological effluent technical specifications (RETS) for operations conducted at Tennessee Valley Authority's Browns Ferry Nuclear Station, Units 1, 2, and 3, during 1983. The two periodic reports reviewed were (a) the Effluents and Waste Disposal Semiannual Report, First Half 1983 and (b) the Effluents and Waste Disposal Semiannual Report, Second Half 1983. The principal review guidelines were the plant's specific RETs and NRC guidance given in NUREG-0133, ''Preparation of Radiological Effluent Technical Specifications for Nuclear Power Plants.'' The Licensee's submitted reports were found to be reasonably completemore » and consistent with the review guidelines.« less

Revisiting the utility of technical performance scores following tetralogy of Fallot repair.

PubMed

Lodin, Daud; Mavrothalassitis, Orestes; Haberer, Kim; Sunderji, Sherzana; Quek, Ruben G W; Peyvandi, Shabnam; Moon-Grady, Anita; Karamlou, Tara

2017-08-01

Although an important quality metric, current technical performance scores may not be generalizable and may omit operative factors that influence outcomes. We examined factors not included in current technical performance scores that may contribute to increased postoperative length of stay, major complications, and cost after primary repair of tetralogy of Fallot. This is a retrospective single site study of patients younger than age 2 years with tetralogy of Fallot undergoing complete repair between 2007 and 2015. Medical record data and discharge echocardiograms were reviewed to ascertain component and composite technical performance scores. Primary outcomes included postoperative length of stay, major complications, and total hospital costs. Multivariable logistic and linear regression identified determinants of each outcome. Patient population (n = 115) had a median postoperative length of stay of 8 days (interquartile range, 6-10 days), and a median total cost of $71,147. Major complications occurred in 33 patients (29%) with 1 death. Technical performance scores assigned were optimum in 28 patients (25%), adequate in 59 patients (52%), and inadequate in 26 patients (23%). Neither technical performance score components nor composite scores were associated with increased postoperative length of stay. Optimum or adequate repairs versus inadequate had equal risk of a complication (P = .79), and equivalent mean total cost ($100,000 vs $187,000; P = .25). Longer cardiopulmonary bypass time per 1-minute increase (P < .01) was associated with longer postoperative length of stay and reintervention (P = .02). The need to return to bypass also increased total cost (P < .01). Current tetralogy of Fallot technical performance scores were not associated with selected outcomes in our postoperative population. Although returning to bypass and bypass length are not included as components in the current score, these are important factors influencing

Technical writing versus technical writing

NASA Technical Reports Server (NTRS)

Dillingham, J. W.

1981-01-01

Two terms, two job categories, 'technical writer' and 'technical author' are discussed in terms of industrial and business requirements and standards. A distinction between 'technical writing' and technical 'writing' is made. The term 'technical editor' is also considered. Problems inherent in the design of programs to prepare and train students for these jobs are discussed. A closer alliance between industry and academia is suggested as a means of preparing students with competent technical communication skills (especially writing and editing skills) and good technical skills.

Mental Fatigue: Impairment of Technical Performance in Small-Sided Soccer Games.

PubMed

Badin, Oliver O; Smith, Mitchell R; Conte, Daniele; Coutts, Aaron J

2016-11-01

To assess the effects of mental fatigue on physical and technical performance in small-sided soccer games. Twenty soccer players (age 17.8 ± 1.0 y, height 179 ± 5 cm, body mass 72.4 ± 6.8 kg, playing experience 8.3 ± 1.4 y) from an Australian National Premier League soccer club volunteered to participate in this randomized crossover investigation. Participants played 15-min 5-vs-5 small-sided games (SSGs) without goalkeepers on 2 occasions separated by 1 wk. Before the SSG, 1 team watched a 30-min emotionally neutral documentary (control), while the other performed 30 min of a computer-based Stroop task (mental fatigue). Subjective ratings of mental and physical fatigue were recorded before and after treatment and after the SSG. Motivation was assessed before treatment and SSG; mental effort was assessed after treatment and SSG. Player activity profiles and heart rate (HR) were measured throughout the SSG, whereas ratings of perceived exertion (RPEs) were recorded before the SSG and immediately after each half. Video recordings of the SSG allowed for notational analysis of technical variables. Subjective ratings of mental fatigue and effort were higher after the Stroop task, whereas motivation for the upcoming SSG was similar between conditions. HR during the SSG was possibly higher in the control condition, whereas RPE was likely higher in the mental-fatigue condition. Mental fatigue had an unclear effect on most physical-performance variables but impaired most technical-performance variables. Mental fatigue impairs technical but not physical performance in small-sided soccer games.

Performance and technical feasibility comparison of reusable launch systems: A synthesis of the ESA winged launcher studies

NASA Astrophysics Data System (ADS)

Berry, W.; Grallert, H.

1996-02-01

The paper presents a synthesis of the performance and technical feasibility assessment of 7 reusable launcher types, comprising 13 different vehicles, studied by European Industry for ESA in the ESA Winged Launcher Study in the period January 1988 to May 1994. The vehicles comprised single-stage-to-orbit (SSTO) and two-stage-to-orbit (TSTO) vehicles, propelled by either air-breathing/rocket propulsion or entirely by rocket propulsion. The results showed that an SSTO vehicle of the HOTOL-type, propelled by subsonic combustion air-breathing/rocket engines could barely deliver the specified payload mass and was aerodynamically unstable; that a TSTO vehicle of the Saenger type, employing subsonic combustion airbreathing propulsion in its first stage and rocket propulsion in its second stage, could readily deliver the specified payload mass and was found to be technically feasible and versatile; that an SSTO vehicle of the NASP type, propelled by supersonic combustion airbreathing/rocket propulsion was able to deliver a reduced payload mass, was very complex and required very advanced technologies; that an air-launched rocket propelled vehicle of the Interim HOTOL type, although technically feasible, could deliver only a reduced payload mass, being constrained by the lifting capability of the carrier airplane; that three different, entirely rocket-propelled vehicles could deliver the specified payload mass, were technically feasible but required relatively advanced technologies.

Technical and physical determinants of soccer match-play performance in elite youth soccer players.

PubMed

Rowat, Owain; Fenner, Jonathan; Unnithan, Viswanath

2017-04-01

The aim of this study was to evaluate whether physical performance characteristics could be a better predictor than technical skills in determining the technical level of county soccer players in a match situation. With institutional ethics approval, 25 male youth soccer players aged 16-18.5 years from a professional soccer academy in South East Asia were selected and height and body mass were recorded. Players were tested for sexual maturity (pubertal development scale [PDS] self-assessment), aerobic capacity (yo-yo intermittent recovery test level 1 [YYIR1]), repeated sprint ability (7 x 35 m sprints) acceleration (15 m sprint) and four soccer skills tests (dribble with pass, dribbling speed, passing and shooting accuracy). Players' technical ability during match play was assessed in small-sided games of soccer (5 v 5) using a novel game technical scoring chart (scoring chart completed by coaches to assess technical performance in a match situation) developed from criteria (e.g., first touch, dribbling and two footedness) used by youth soccer coaches for talent identification. A Spearman's rank correlation showed the YYIR1 test and 15 m sprint test were limited in predicting technical match performance (r=0.03, P=0.88, r=-0.23, P=0.32 respectively). A Pearson product moment correlation showed that the repeated sprint test was also limited in predicting technical match performance (r=-0.34, P=0.14). A dribbling skill with a pass was found to be the best determinant of a player's technical ability in a match (r=-0.57, P=0.00). Talent identification and selection programs in Asian youth soccer should include a dribbling skill performed with a pass.

Technical Performance as a Predictor of Clinical Outcomes in Laparoscopic Gastric Cancer Surgery.

PubMed

Fecso, Andras B; Bhatti, Junaid A; Stotland, Peter K; Quereshy, Fayez A; Grantcharov, Teodor P

2018-03-23

The purpose of this study was to evaluate the relationship between technical performance and patient outcomes in laparoscopic gastric cancer surgery. Laparoscopic gastrectomy for cancer is an advanced procedure with high rate of postoperative morbidity and mortality. Many variables including patient, disease, and perioperative management factors have been shown to impact postoperative outcomes; however, the role of surgical performance is insufficiently investigated. A retrospective review was performed for all patients who had undergone laparoscopic gastrectomy for cancer at 3 teaching institutions between 2009 and 2015. Patients with available, unedited video-recording of their procedure were included in the study. Video files were rated for technical performance, using Objective Structured Assessments of Technical Skills (OSATS) and Generic Error Rating Tool instruments. The main outcome variable was major short-term complications. The effect of technical performance on patient outcomes was assessed using logistic regression analysis with backward selection strategy. Sixty-one patients with available video recordings were included in the study. The overall complication rate was 29.5%. The mean Charlson comorbidity index, type of procedure, and the global OSATS score were included in the final predictive model. Lower performance score (OSATS ≤29) remained an independent predictor for major short-term outcomes (odds ratio 6.49), while adjusting for comorbidities and type of procedure. Intraoperative technical performance predicts major short-term outcomes in laparoscopic gastrectomy for cancer. Ongoing assessment and enhancement of surgical skills using modern, evidence-based strategies might improve short-term patient outcomes. Future work should focus on developing and studying the effectiveness of such interventions in laparoscopic gastric cancer surgery.

Pulsed Lidar Performance/Technical Maturity Assessment

NASA Technical Reports Server (NTRS)

Gimmestad, Gary G.; West, Leanne L.; Wood, Jack W.; Frehlich, Rod

2004-01-01

This report describes the results of investigations performed by the Georgia Tech Research Institute (GTRI) and the National Center for Atmospheric Research (NCAR) under a task entitled 'Pulsed Lidar Performance/Technical Maturity Assessment' funded by the Crew Systems Branch of the Airborne Systems Competency at the NASA Langley Research Center. The investigations included two tasks, 1.1(a) and 1.1(b). The Tasks discussed in this report are in support of the NASA Virtual Airspace Modeling and Simulation (VAMS) program and are designed to evaluate a pulsed lidar that will be required for active wake vortex avoidance solutions. The Coherent Technologies, Inc. (CTI) WindTracer LIDAR is an eye-safe, 2-micron, coherent, pulsed Doppler lidar with wake tracking capability. The actual performance of the WindTracer system was to be quantified. In addition, the sensor performance has been assessed and modeled, and the models have been included in simulation efforts. The WindTracer LIDAR was purchased by the Federal Aviation Administration (FAA) for use in near-term field data collection efforts as part of a joint NASA/FAA wake vortex research program. In the joint research program, a minimum common wake and weather data collection platform will be defined. NASA Langley will use the field data to support wake model development and operational concept investigation in support of the VAMS project, where the ultimate goal is to improve airport capacity and safety. Task 1.1(a), performed by NCAR in Boulder, Colorado to analyze the lidar system to determine its performance and capabilities based on results from simulated lidar data with analytic wake vortex models provided by NASA, which were then compared to the vendor's claims for the operational specifications of the lidar. Task 1.1(a) is described in Section 3, including the vortex model, lidar parameters and simulations, and results for both detection and tracking of wake vortices generated by Boeing 737s and 747s. Task 1

19 CFR 115.65 - Technical requirements for road vehicles by design type.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 19 Customs Duties 1 2012-04-01 2012-04-01 false Technical requirements for road vehicles by design type. 115.65 Section 115.65 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO...

19 CFR 115.65 - Technical requirements for road vehicles by design type.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 19 Customs Duties 1 2011-04-01 2011-04-01 false Technical requirements for road vehicles by design type. 115.65 Section 115.65 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO...

19 CFR 115.65 - Technical requirements for road vehicles by design type.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 19 Customs Duties 1 2013-04-01 2013-04-01 false Technical requirements for road vehicles by design type. 115.65 Section 115.65 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO...

19 CFR 115.65 - Technical requirements for road vehicles by design type.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 19 Customs Duties 1 2014-04-01 2014-04-01 false Technical requirements for road vehicles by design type. 115.65 Section 115.65 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO...

19 CFR 115.65 - Technical requirements for road vehicles by design type.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Technical requirements for road vehicles by design type. 115.65 Section 115.65 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY CARGO CONTAINER AND ROAD VEHICLE CERTIFICATION PURSUANT TO...

The impact of fatigue on the non-technical skills performance of critical care air ambulance clinicians.

PubMed

Myers, J A; Powell, D M C; Aldington, S; Sim, D; Psirides, A; Hathaway, K; Haney, M F

2017-11-01

The relationship between fatigue-related risk and impaired clinical performance is not entirely clear. Non-technical factors represent an important component of clinical performance and may be sensitive to the effects of fatigue. The hypothesis was that the sum score of overall non-technical performance is degraded by fatigue. Nineteen physicians undertook two different simulated air ambulance missions, once when rested, and once when fatigued (randomised crossover design). Trained assessors blinded to participants' fatigue status performed detailed structured assessments based on expected behaviours in four non-technical skills domains: teamwork, situational awareness, task management, and decision making. Participants also provided self-ratings of their performance. The primary endpoint was the sum score of overall non-technical performance. The main finding, the overall non-technical skills performance rating of the clinicians, was better in rested than fatigued states (mean difference with 95% CI, 2.8 [2.2-3.4]). The findings remained consistent across individual non-technical skills domains; also when controlling for an order effect and examining the impact of a number of possible covariates. There was no difference in self-ratings of clinical performance between rested and fatigued states. Non-technical performance of critical care air transfer clinicians is degraded when they are fatigued. Fatigued clinicians may fail to recognise the degree to which their performance is compromised. These findings represent risk to clinical care quality and patient safety in the dynamic and isolated environment of air ambulance transfer. © 2017 The Acta Anaesthesiologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.

76 FR 57060 - International Cooperation on Harmonisation of Technical Requirements for Registration of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-15

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2011-D-0588] International Cooperation on Harmonisation of Technical Requirements for Registration of Veterinary Medicinal Products; Draft Guidance for Industry on Pharmacovigilance of Veterinary Medicinal Products: Electronic...

Performance Evaluation of Indian Technical Institutions Using PROMETHEE-GAIA Approach

ERIC Educational Resources Information Center

Ranjan, Rajeev; Chakraborty, Shankar

2015-01-01

It has now become an important issue to evaluate the performance of technical institutions to develop better research and enrich the existing teaching processes. The results of such performance appraisal would serve as a reference point for decisions to choose a particular institution, hire manpower, and provide financial support for the…

50 CFR 91.13 - Technical requirements for design and submission of entry.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 50 Wildlife and Fisheries 9 2014-10-01 2014-10-01 false Technical requirements for design and submission of entry. 91.13 Section 91.13 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR (CONTINUED) MISCELLANEOUS PROVISIONS MIGRATORY BIRD HUNTING AND CONSERVATION STAMP CONTEST Procedures for Entering the...

50 CFR 91.13 - Technical requirements for design and submission of entry.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 50 Wildlife and Fisheries 9 2012-10-01 2012-10-01 false Technical requirements for design and submission of entry. 91.13 Section 91.13 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR (CONTINUED) MISCELLANEOUS PROVISIONS MIGRATORY BIRD HUNTING AND CONSERVATION STAMP CONTEST Procedures for Entering the...

14 CFR 171.109 - Performance requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Performance requirements. 171.109 Section... Performance requirements. (a) The Simplified Directional Facility must perform in accordance with the... performance and compliance with applicable performance requirements must be conducted in accordance with the...

14 CFR 171.109 - Performance requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Performance requirements. 171.109 Section... Performance requirements. (a) The Simplified Directional Facility must perform in accordance with the... performance and compliance with applicable performance requirements must be conducted in accordance with the...

14 CFR 171.109 - Performance requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Performance requirements. 171.109 Section... Performance requirements. (a) The Simplified Directional Facility must perform in accordance with the... performance and compliance with applicable performance requirements must be conducted in accordance with the...

14 CFR 171.109 - Performance requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Performance requirements. 171.109 Section... Performance requirements. (a) The Simplified Directional Facility must perform in accordance with the... performance and compliance with applicable performance requirements must be conducted in accordance with the...

16 CFR 1402.4 - Requirements to provide performance and technical data by labeling and instructions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... technical data by labeling and instructions. 1402.4 Section 1402.4 Commercial Practices CONSUMER PRODUCT... instructions. (a) Notice to purchasers. Manufacturers of CB base station antennas, TV antennas, and antenna... Charts, which display the desired color within the tolerance limits. (ii) Instructions. CB base station...

76 FR 57058 - International Cooperation on Harmonisation of Technical Requirements for Registration of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-15

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2010-D-0165] International Cooperation on Harmonisation of Technical Requirements for Registration of Veterinary Medicinal Products; Guidance for Industry on Studies To Evaluate the Metabolism and Residue Kinetics of Veterinary...

Technical Requirements Analysis and Control Systems (TRACS) Initial Operating Capability (IOC) documentation

NASA Technical Reports Server (NTRS)

Hammond, Dana P.

1991-01-01

The Technical Requirements Analysis and Control Systems (TRACS) software package is described. TRACS offers supplemental tools for the analysis, control, and interchange of project requirements. This package provides the fundamental capability to analyze and control requirements, serves a focal point for project requirements, and integrates a system that supports efficient and consistent operations. TRACS uses relational data base technology (ORACLE) in a stand alone or in a distributed environment that can be used to coordinate the activities required to support a project through its entire life cycle. TRACS uses a set of keyword and mouse driven screens (HyperCard) which imposes adherence through a controlled user interface. The user interface provides an interactive capability to interrogate the data base and to display or print project requirement information. TRACS has a limited report capability, but can be extended with PostScript conventions.

SHARP's systems engineering challenge: rectifying integrated product team requirements with performance issues in an evolutionary spiral development acquisition

NASA Astrophysics Data System (ADS)

Kuehl, C. Stephen

2003-08-01

Completing its final development and early deployment on the Navy's multi-role aircraft, the F/A-18 E/F Super Hornet, the SHAred Reconnaissance Pod (SHARP) provides the war fighter with the latest digital tactical reconnaissance (TAC Recce) Electro-Optical/Infrared (EO/IR) sensor system. The SHARP program is an evolutionary acquisition that used a spiral development process across a prototype development phase tightly coupled into overlapping Engineering and Manufacturing Development (EMD) and Low Rate Initial Production (LRIP) phases. Under a tight budget environment with a highly compressed schedule, SHARP challenged traditional acquisition strategies and systems engineering (SE) processes. Adopting tailored state-of-the-art systems engineering process models allowd the SHARP program to overcome the technical knowledge transition challenges imposed by a compressed program schedule. The program's original goal was the deployment of digital TAC Recce mission capabilities to the fleet customer by summer of 2003. Hardware and software integration technical challenges resulted from requirements definition and analysis activities performed across a government-industry led Integrated Product Team (IPT) involving Navy engineering and test sites, Boeing, and RTSC-EPS (with its subcontracted hardware and government furnished equipment vendors). Requirements development from a bottoms-up approach was adopted using an electronic requirements capture environment to clarify and establish the SHARP EMD product baseline specifications as relevant technical data became available. Applying Earned-Value Management (EVM) against an Integrated Master Schedule (IMS) resulted in efficiently managing SE task assignments and product deliveries in a dynamically evolving customer requirements environment. Application of Six Sigma improvement methodologies resulted in the uncovering of root causes of errors in wiring interconnectivity drawings, pod manufacturing processes, and avionics

OrbView-3 Technical Performance Evaluation 2005: Modulation Transfer Function

NASA Technical Reports Server (NTRS)

Cole, Aaron

2007-01-01

The Technical performance evaluation of OrbView-3 using the Modulation Transfer Function (MTF) is presented. The contents include: 1) MTF Results and Methodology; 2) Radiometric Calibration Methodology; and 3) Relative Radiometric Assessment Results

1988 Underground Storage Tanks; Technical Requirements; Final Rule and Underground Storage Tanks Containing Petroleum-Financial Responsibility Requirements and State Program Approval Objective; Final Rule

EPA Pesticide Factsheets

EPA's 1988 regulations concerning USTs are contained in 40 CFR Part 280, 40 CFR Part 281 and 40 CFR Parts 282.50-282.105 and divided into three sections: technical requirements, financial responsibility requirements, and state program approval objectives.

14 CFR 171.157 - Performance requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Performance requirements. 171.157 Section... Performance requirements. (a) The DME must meet the performance requirements set forth in the “International... functional and performance characteristics of the DME transponder must be conducted in accordance with the...

10 CFR 70.61 - Performance requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 2 2012-01-01 2012-01-01 false Performance requirements. 70.61 Section 70.61 Energy... Performance requirements. (a) Each applicant or licensee shall evaluate, in the integrated safety analysis performed in accordance with § 70.62, its compliance with the performance requirements in paragraphs (b), (c...

14 CFR 171.157 - Performance requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Performance requirements. 171.157 Section... Performance requirements. (a) The DME must meet the performance requirements set forth in the “International... functional and performance characteristics of the DME transponder must be conducted in accordance with the...

14 CFR 171.157 - Performance requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Performance requirements. 171.157 Section... Performance requirements. (a) The DME must meet the performance requirements set forth in the “International... functional and performance characteristics of the DME transponder must be conducted in accordance with the...

14 CFR 171.157 - Performance requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Performance requirements. 171.157 Section... Performance requirements. (a) The DME must meet the performance requirements set forth in the “International... functional and performance characteristics of the DME transponder must be conducted in accordance with the...

10 CFR 70.61 - Performance requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 2 2014-01-01 2014-01-01 false Performance requirements. 70.61 Section 70.61 Energy... Performance requirements. (a) Each applicant or licensee shall evaluate, in the integrated safety analysis performed in accordance with § 70.62, its compliance with the performance requirements in paragraphs (b), (c...

14 CFR 171.157 - Performance requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Performance requirements. 171.157 Section... Performance requirements. (a) The DME must meet the performance requirements set forth in the “International... functional and performance characteristics of the DME transponder must be conducted in accordance with the...

10 CFR 70.61 - Performance requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 2 2011-01-01 2011-01-01 false Performance requirements. 70.61 Section 70.61 Energy... Performance requirements. (a) Each applicant or licensee shall evaluate, in the integrated safety analysis performed in accordance with § 70.62, its compliance with the performance requirements in paragraphs (b), (c...

10 CFR 70.61 - Performance requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Performance requirements. 70.61 Section 70.61 Energy... Performance requirements. (a) Each applicant or licensee shall evaluate, in the integrated safety analysis performed in accordance with § 70.62, its compliance with the performance requirements in paragraphs (b), (c...

Intra-operative disruptions, surgeon's mental workload, and technical performance in a full-scale simulated procedure.

PubMed

Weigl, Matthias; Stefan, Philipp; Abhari, Kamyar; Wucherer, Patrick; Fallavollita, Pascal; Lazarovici, Marc; Weidert, Simon; Euler, Ekkehard; Catchpole, Ken

2016-02-01

Surgical flow disruptions occur frequently and jeopardize perioperative care and surgical performance. So far, insights into subjective and cognitive implications of intra-operative disruptions for surgeons and inherent consequences for performance are inconsistent. This study aimed to investigate the effect of surgical flow disruption on surgeon's intra-operative workload and technical performance. In a full-scale OR simulation, 19 surgeons were randomly allocated to either of the two disruption scenarios (telephone call vs. patient discomfort). Using a mixed virtual reality simulator with a computerized, high-fidelity mannequin, all surgeons were trained in performing a vertebroplasty procedure and subsequently performed such a procedure under experimental conditions. Standardized measures on subjective workload and technical performance (trocar positioning deviation from expert-defined standard, number, and duration of X-ray acquisitions) were collected. Intra-operative workload during simulated disruption scenarios was significantly higher compared to training sessions (p < .01). Surgeons in the telephone call scenario experienced significantly more distraction compared to their colleagues in the patient discomfort scenario (p < .05). However, workload tended to be increased in surgeons who coped with distractions due to patient discomfort. Technical performance was not significantly different between both disruption scenarios. We found a significant association between surgeons' intra-operative workload and technical performance such that surgeons with increased mental workload tended to perform worse (β = .55, p = .04). Surgical flow disruptions affect surgeons' intra-operative workload. Increased mental workload was associated with inferior technical performance. Our simulation-based findings emphasize the need to establish smooth surgical flow which is characterized by a low level of process deviations and disruptions.

A research review on clinical needs, technical requirements, and normativity in the design of surgical robots.

PubMed

Díaz, Carlos Eduardo; Fernández, Roemi; Armada, Manuel; García, Felipe

2017-12-01

Nowadays robots play an important role in society, mainly due to the significant benefits they provide when utilized for assisting human beings in the execution of dangerous or repetitive tasks. Medicine is one of the fields in which robots are gaining greater use and development, especially those employed in minimally invasive surgery (MIS). However, due to the particular conditions of the human body where robots have to act, the design of these systems is complex, not only from a technical point of view, but also because the clinical needs and the normativity aspects are important considerations that have to be taken into account in order to achieve better performances and more secure systems for patients and surgeons. Thus, this paper explores the clinical needs and the technical requirements that will trace the roadmap for the next scientific and technological advances in the field of robotic surgery, the metrics that should be defined for safe technology development and the standards that are being elaborated for boosting the industry and facilitating systems integration. Copyright © 2017 John Wiley & Sons, Ltd.

14 CFR 171.27 - Performance requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Performance requirements. 171.27 Section 171.27 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... Performance requirements. (a) The facility must meet the performance requirements set forth in the...

14 CFR 171.27 - Performance requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Performance requirements. 171.27 Section 171.27 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... Performance requirements. (a) The facility must meet the performance requirements set forth in the...

14 CFR 171.27 - Performance requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Performance requirements. 171.27 Section 171.27 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... Performance requirements. (a) The facility must meet the performance requirements set forth in the...

14 CFR 171.27 - Performance requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Performance requirements. 171.27 Section 171.27 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... Performance requirements. (a) The facility must meet the performance requirements set forth in the...

A Perkins Challenge: Assessing Technical Skills in CTE

ERIC Educational Resources Information Center

Stone, James R., III

2009-01-01

Federal law requires state to develop performance measures and data-collection systems for secondary and postsecondary technical-skill attainment. This poses many challenges, such as defining a technical skills, measurement and when to assess students. In this article, the author outlines various assessment models and looks at the challenges…

14 CFR 171.207 - Performance requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Performance requirements. 171.207 Section...) NAVIGATIONAL FACILITIES NON-FEDERAL NAVIGATION FACILITIES VHF Marker Beacons § 171.207 Performance requirements. (a) VHF Marker Beacons must meet the performance requirements set forth in the “International...

14 CFR 171.207 - Performance requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Performance requirements. 171.207 Section...) NAVIGATIONAL FACILITIES NON-FEDERAL NAVIGATION FACILITIES VHF Marker Beacons § 171.207 Performance requirements. (a) VHF Marker Beacons must meet the performance requirements set forth in the “International...

14 CFR 171.207 - Performance requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Performance requirements. 171.207 Section...) NAVIGATIONAL FACILITIES NON-FEDERAL NAVIGATION FACILITIES VHF Marker Beacons § 171.207 Performance requirements. (a) VHF Marker Beacons must meet the performance requirements set forth in the “International...

77 FR 34784 - Removal of Six Month Line Check Requirement for Pilots Over Age 60; Technical Amendment

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-12

...-0486; Amdt. No. 121-359] Removal of Six Month Line Check Requirement for Pilots Over Age 60; Technical... years of age that applied to air carriers engaged in part 121 operations. This technical amendment... December 13, 2007. This legislation raised the upper age limit for pilots in part 121 from age 60 to age 65...

Optimized technical and scientific design approach for high performance anticoincidence shields

NASA Astrophysics Data System (ADS)

Graue, Roland; Stuffler, Timo; Monzani, Franco; Bastia, Paolo; Gryksa, Werner; Pahl, Germit

2018-04-01

This paper, "Optimized technical and scientific design approach for high performance anticoincidence shields," was presented as part of International Conference on Space Optics—ICSO 1997, held in Toulouse, France.

Longitudinal Trend Analysis of Performance Indicators for South Carolina's Technical Colleges

ERIC Educational Resources Information Center

Hossain, Mohammad Nurul

2010-01-01

This study included an analysis of the trend of performance indicators for the technical college sector of higher education in South Carolina. In response to demands for accountability and transparency in higher education, the state of South Carolina developed sector specific performance indicators to measure various educational outcomes for each…

47 CFR 80.275 - Technical Requirements for Class A Automatic Identification System (AIS) equipment.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Compulsory Ships § 80.275 Technical Requirements for Class A Automatic Identification System (AIS) equipment. (a) Prior to submitting a certification application for a Class A AIS device, the following... Identification System (AIS) equipment. 80.275 Section 80.275 Telecommunication FEDERAL COMMUNICATIONS COMMISSION...

47 CFR 80.275 - Technical Requirements for Class A Automatic Identification System (AIS) equipment.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Compulsory Ships § 80.275 Technical Requirements for Class A Automatic Identification System (AIS) equipment. (a) Prior to submitting a certification application for a Class A AIS device, the following... Identification System (AIS) equipment. 80.275 Section 80.275 Telecommunication FEDERAL COMMUNICATIONS COMMISSION...

47 CFR 80.275 - Technical Requirements for Class A Automatic Identification System (AIS) equipment.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Compulsory Ships § 80.275 Technical Requirements for Class A Automatic Identification System (AIS) equipment. (a) Prior to submitting a certification application for a Class A AIS device, the following... Identification System (AIS) equipment. 80.275 Section 80.275 Telecommunication FEDERAL COMMUNICATIONS COMMISSION...

47 CFR 80.275 - Technical Requirements for Class A Automatic Identification System (AIS) equipment.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Compulsory Ships § 80.275 Technical Requirements for Class A Automatic Identification System (AIS) equipment. (a) Prior to submitting a certification application for a Class A AIS device, the following... Identification System (AIS) equipment. 80.275 Section 80.275 Telecommunication FEDERAL COMMUNICATIONS COMMISSION...

Technical Efficiency and Organ Transplant Performance: A Mixed-Method Approach

PubMed Central

de-Pablos-Heredero, Carmen; Fernández-Renedo, Carlos; Medina-Merodio, Jose-Amelio

2015-01-01

Mixed methods research is interesting to understand complex processes. Organ transplants are complex processes in need of improved final performance in times of budgetary restrictions. As the main objective a mixed method approach is used in this article to quantify the technical efficiency and the excellence achieved in organ transplant systems and to prove the influence of organizational structures and internal processes in the observed technical efficiency. The results show that it is possible to implement mechanisms for the measurement of the different components by making use of quantitative and qualitative methodologies. The analysis show a positive relationship between the levels related to the Baldrige indicators and the observed technical efficiency in the donation and transplant units of the 11 analyzed hospitals. Therefore it is possible to conclude that high levels in the Baldrige indexes are a necessary condition to reach an increased level of the service offered. PMID:25950653

Mental Fatigue Impairs Soccer-Specific Physical and Technical Performance.

PubMed

Smith, Mitchell R; Coutts, Aaron J; Merlini, Michele; Deprez, Dieter; Lenoir, Matthieu; Marcora, Samuele M

2016-02-01

To investigate the effects of mental fatigue on soccer-specific physical and technical performance. This investigation consisted of two separate studies. Study 1 assessed the soccer-specific physical performance of 12 moderately trained soccer players using the Yo-Yo Intermittent Recovery Test, Level 1 (Yo-Yo IR1). Study 2 assessed the soccer-specific technical performance of 14 experienced soccer players using the Loughborough Soccer Passing and Shooting Tests (LSPT, LSST). Each test was performed on two occasions and preceded, in a randomized, counterbalanced order, by 30 min of the Stroop task (mentally fatiguing treatment) or 30 min of reading magazines (control treatment). Subjective ratings of mental fatigue were measured before and after treatment, and mental effort and motivation were measured after treatment. Distance run, heart rate, and ratings of perceived exertion were recorded during the Yo-Yo IR1. LSPT performance time was calculated as original time plus penalty time. LSST performance was assessed using shot speed, shot accuracy, and shot sequence time. Subjective ratings of mental fatigue and effort were higher after the Stroop task in both studies (P < 0.001), whereas motivation was similar between conditions. This mental fatigue significantly reduced running distance in the Yo-Yo IR1 (P < 0.001). No difference in heart rate existed between conditions, whereas ratings of perceived exertion were significantly higher at iso-time in the mental fatigue condition (P < 0.01). LSPT original time and performance time were not different between conditions; however, penalty time significantly increased in the mental fatigue condition (P = 0.015). Mental fatigue also impaired shot speed (P = 0.024) and accuracy (P < 0.01), whereas shot sequence time was similar between conditions. Mental fatigue impairs soccer-specific running, passing, and shooting performance.

Temporal Changes in Technical and Physical Performances During a Small-Sided Game in Elite Youth Soccer Players

PubMed Central

Moreira, Alexandre; Saldanha Aoki, Marcelo; Carling, Chris; Alan Rodrigues Lopes, Rafael; Felipe Schultz de Arruda, Ademir; Lima, Marcelo; Cesar Correa, Umberto; Bradley, Paul S

2016-01-01

Background There have been claims that small-sided games (SSG) may generate an appropriate environment to develop youth players’ technical performance associated to game-related problem solving. However, the temporal change in technical performance parameters of youth players during SSG is still unknown. Objectives The aim of this study was to examine temporal changes in technical and physical performances during a small-sided game (SSG) in elite soccer players. Methods Sixty elite youth players (age 14.8 ± 0.2 yr; stature 177 ± 5 cm; body mass 66.2 ± 4.7 kg) completed a 5 v 5 SSG using two repetitions of 8 minutes interspersed by 3 minutes of passive recovery. To evaluate temporal changes in performance, the data were analysed across 4 minutes quarters. Physical performance parameters included the total distance covered (TDC), the frequency of sprints (>18 km•h-1), accelerations and decelerations (> 2.0 m•s-2 and - 2.0 m•s-2), metabolic power (W•kg-1), training impulse (TRIMP), TDC: TRIMP, number of impacts, and body load. Technical performance parameters included goal attempts, total number of tackles, tackles and interceptions, total number of passes, and passes effectiveness. Results All physical performance parameters decreased from the first to the last quarter with notable declines in TDC, metabolic power and the frequency of sprints, accelerations and decelerations (P < 0.05; moderate to very large ES: 1.08 - 3.30). However, technical performance parameters did not vary across quarters (P > 0.05; trivial ES for 1st v 4th quarters: 0.15 - 0.33). Conclusions The data demonstrate that technical performance is maintained despite substantial declines in physical performance during a SSG in elite youth players. This finding may have implications for designing SSG’s for elite youth players to ensure physical, technical and tactical capabilities are optimized. Modifications in player number, pitch dimensions, rules, coach encouragement, for instance

Temporal Changes in Technical and Physical Performances During a Small-Sided Game in Elite Youth Soccer Players.

PubMed

Moreira, Alexandre; Saldanha Aoki, Marcelo; Carling, Chris; Alan Rodrigues Lopes, Rafael; Felipe Schultz de Arruda, Ademir; Lima, Marcelo; Cesar Correa, Umberto; Bradley, Paul S

2016-12-01

There have been claims that small-sided games (SSG) may generate an appropriate environment to develop youth players' technical performance associated to game-related problem solving. However, the temporal change in technical performance parameters of youth players during SSG is still unknown. The aim of this study was to examine temporal changes in technical and physical performances during a small-sided game (SSG) in elite soccer players. Sixty elite youth players (age 14.8 ± 0.2 yr; stature 177 ± 5 cm; body mass 66.2 ± 4.7 kg) completed a 5 v 5 SSG using two repetitions of 8 minutes interspersed by 3 minutes of passive recovery. To evaluate temporal changes in performance, the data were analysed across 4 minutes quarters. Physical performance parameters included the total distance covered (TDC), the frequency of sprints (>18 km•h -1 ), accelerations and decelerations (> 2.0 m•s -2 and - 2.0 m•s -2 ), metabolic power (W•kg -1 ), training impulse (TRIMP), TDC: TRIMP, number of impacts, and body load. Technical performance parameters included goal attempts, total number of tackles, tackles and interceptions, total number of passes, and passes effectiveness. All physical performance parameters decreased from the first to the last quarter with notable declines in TDC, metabolic power and the frequency of sprints, accelerations and decelerations (P < 0.05; moderate to very large ES: 1.08 - 3.30). However, technical performance parameters did not vary across quarters (P > 0.05; trivial ES for 1st v 4th quarters: 0.15 - 0.33). The data demonstrate that technical performance is maintained despite substantial declines in physical performance during a SSG in elite youth players. This finding may have implications for designing SSG's for elite youth players to ensure physical, technical and tactical capabilities are optimized. Modifications in player number, pitch dimensions, rules, coach encouragement, for instance, should be included taking into account the

Hydrogen monitoring requirements in the global technical regulation on hydrogen and fuel cell vehicles

DOE PAGES

Buttner, William; Rivkin, C.; Burgess, R.; ...

2017-02-04

Here, the United Nations Economic Commission for Europe Global Technical Regulation (GTR) Number 13 ( Global Technical Regulation on Hydrogen and Fuel Cell Vehicles) is the defining document regulating safety requirements in hydrogen vehicles, and in particular, fuel cell electric vehicles (FCEVs). GTR Number 13 has been formally adopted and will serve as the basis for the national regulatory standards for FCEV safety in North America (led by the United States), Japan, Korea, and the European Union. The GTR defines safety requirements for these vehicles, including specifications on the allowable hydrogen levels in vehicle enclosures during in-use and post-crash conditionsmore » and on the allowable hydrogen emissions levels in vehicle exhaust during certain modes of normal operation. However, in order to be incorporated into national regulations, that is, to be legally binding, methods to verify compliance with the specific requirements must exist. In a collaborative program, the Sensor Laboratories at the National Renewable Energy Laboratory in the United States and the Joint Research Centre, Institute for Energy and Transport in the Netherlands have been evaluating and developing analytical methods that can be used to verify compliance with the hydrogen release requirements as specified in the GTR.« less

Research on the technical requirements standards of high efficiency precipitator in power industries for assessment

NASA Astrophysics Data System (ADS)

Jin, Huang; Ling, Lin; Jun, Guo; Jianguo, Li; Yongzhong, Wang

2017-11-01

Facing the increasingly severe situation of air pollution, China are now positively promoting the evaluation of high efficiency air pollution control equipments and the research of the relative national standards. This paper showed the significance and the effect of formulating the technical requirements of high efficiency precipitator equipments for assessment national standards in power industries as well as the research thoughts and principle of these standards. It introduce the qualitative and quantitative evaluation requirements of high efficiency precipitators using in power industries and the core technical content such as testing, calculating, evaluation methods and so on. The implementation of a series of national standards is in order to lead and promote the production and application of high efficiency precipitator equipments in the field of the prevention of air pollution in national power industries.

78 FR 52963 - 60-Day Notice of Proposed Information Collection: Technical Processing Requirements for...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-27

... Information Collection: Technical Processing Requirements for Multifamily Project Mortgage Insurance AGENCY...: HUD is seeking approval from the Office of Management and Budget (OMB) for the information collection... interested parties on the proposed collection of information. The purpose of this notice is to allow for 60...

47 CFR 15.509 - Technical requirements for ground penetrating radars and wall imaging systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 1 2011-10-01 2011-10-01 false Technical requirements for ground penetrating radars and wall imaging systems. 15.509 Section 15.509 Telecommunication FEDERAL COMMUNICATIONS... ground penetrating radars and wall imaging systems. (a) The UWB bandwidth of an imaging system operating...

47 CFR 15.509 - Technical requirements for ground penetrating radars and wall imaging systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 1 2013-10-01 2013-10-01 false Technical requirements for ground penetrating radars and wall imaging systems. 15.509 Section 15.509 Telecommunication FEDERAL COMMUNICATIONS... ground penetrating radars and wall imaging systems. (a) The UWB bandwidth of an imaging system operating...

47 CFR 15.509 - Technical requirements for ground penetrating radars and wall imaging systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 1 2012-10-01 2012-10-01 false Technical requirements for ground penetrating radars and wall imaging systems. 15.509 Section 15.509 Telecommunication FEDERAL COMMUNICATIONS... ground penetrating radars and wall imaging systems. (a) The UWB bandwidth of an imaging system operating...

47 CFR 15.509 - Technical requirements for ground penetrating radars and wall imaging systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 1 2014-10-01 2014-10-01 false Technical requirements for ground penetrating radars and wall imaging systems. 15.509 Section 15.509 Telecommunication FEDERAL COMMUNICATIONS... ground penetrating radars and wall imaging systems. (a) The UWB bandwidth of an imaging system operating...

47 CFR 15.509 - Technical requirements for ground penetrating radars and wall imaging systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Technical requirements for ground penetrating radars and wall imaging systems. 15.509 Section 15.509 Telecommunication FEDERAL COMMUNICATIONS... ground penetrating radars and wall imaging systems. (a) The UWB bandwidth of an imaging system operating...

7 CFR 652.21 - Certification criteria and requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... must: (1) Have the required technical training, education, and experience to perform the level of technical assistance for which certification is sought; (2) Meet any applicable professional or business... CONSERVATION SERVICE, DEPARTMENT OF AGRICULTURE SUPPORT ACTIVITIES TECHNICAL SERVICE PROVIDER ASSISTANCE...

Organizing Performance Requirements For Dynamical Systems

NASA Technical Reports Server (NTRS)

Malchow, Harvey L.; Croopnick, Steven R.

1990-01-01

Paper describes methodology for establishing performance requirements for complicated dynamical systems. Uses top-down approach. In series of steps, makes connections between high-level mission requirements and lower-level functional performance requirements. Provides systematic delineation of elements accommodating design compromises.

Writing Performance Goals: Strategy and Prototypes. A Manual for Vocational and Technical Educators.

ERIC Educational Resources Information Center

McGraw-Hill Book Co., New York, NY. Gregg Div.

The result of a cooperative project of the Center for Vocational and Technical Education at the Ohio State University and the McGraw-Hill Book Company, this manual was prepared to develop prototypes of performance goals for use by curriculum specialists and developers of instructional materials in vocational and technical education and to provide…

10 CFR 35.2647 - Records of additional technical requirements for mobile remote afterloader units.

Code of Federal Regulations, 2010 CFR

2010-01-01

... remote afterloader units. 35.2647 Section 35.2647 Energy NUCLEAR REGULATORY COMMISSION MEDICAL USE OF BYPRODUCT MATERIAL Records § 35.2647 Records of additional technical requirements for mobile remote afterloader units. (a) A licensee shall retain a record of each check for mobile remote afterloader units...

10 CFR 35.2647 - Records of additional technical requirements for mobile remote afterloader units.

Code of Federal Regulations, 2013 CFR

2013-01-01

... remote afterloader units. 35.2647 Section 35.2647 Energy NUCLEAR REGULATORY COMMISSION MEDICAL USE OF BYPRODUCT MATERIAL Records § 35.2647 Records of additional technical requirements for mobile remote afterloader units. (a) A licensee shall retain a record of each check for mobile remote afterloader units...

10 CFR 35.2647 - Records of additional technical requirements for mobile remote afterloader units.

Code of Federal Regulations, 2011 CFR

2011-01-01

... remote afterloader units. 35.2647 Section 35.2647 Energy NUCLEAR REGULATORY COMMISSION MEDICAL USE OF BYPRODUCT MATERIAL Records § 35.2647 Records of additional technical requirements for mobile remote afterloader units. (a) A licensee shall retain a record of each check for mobile remote afterloader units...

10 CFR 35.2647 - Records of additional technical requirements for mobile remote afterloader units.

Code of Federal Regulations, 2014 CFR

2014-01-01

... remote afterloader units. 35.2647 Section 35.2647 Energy NUCLEAR REGULATORY COMMISSION MEDICAL USE OF BYPRODUCT MATERIAL Records § 35.2647 Records of additional technical requirements for mobile remote afterloader units. (a) A licensee shall retain a record of each check for mobile remote afterloader units...

10 CFR 35.2647 - Records of additional technical requirements for mobile remote afterloader units.

Code of Federal Regulations, 2012 CFR

2012-01-01

... remote afterloader units. 35.2647 Section 35.2647 Energy NUCLEAR REGULATORY COMMISSION MEDICAL USE OF BYPRODUCT MATERIAL Records § 35.2647 Records of additional technical requirements for mobile remote afterloader units. (a) A licensee shall retain a record of each check for mobile remote afterloader units...

The Relationship of Aptitudes to the Performance of Skilled Technical Jobs in Engine Manufacturing. Technical Report 1982-5 [and Supplement].

ERIC Educational Resources Information Center

Daniel, Mark; And Others

A study examined the relationship of aptitudes to the performance of skilled technical jobs in engine manufacturing. During the study, several approaches were utilized, including criterion-referenced validation, taxonomic validation, construct validation, and detailed anlaysis of the behaviors involved in performing the jobs. The study sample…

Technical Requirements For Reactors To Be Deployed Internationally For the Global Nuclear Energy Partnership

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ingersoll, Daniel T

2007-01-01

Technical Requirements For Reactors To Be Deployed Internationally For the Global Nuclear Energy Partnership Robert Price U.S. Department of Energy, 1000 Independence Ave, SW, Washington, DC 20585, Daniel T. Ingersoll Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831-6162, INTRODUCTION The Global Nuclear Energy Partnership (GNEP) seeks to create an international regime to support large-scale growth in the worldwide use of nuclear energy. Fully meeting the GNEP vision may require the deployment of thousands of reactors in scores of countries, many of which do not use nuclear energy currently. Some of these needs will be met by large-scalemore » Generation III and III+ reactors (>1000 MWe) and Generation IV reactors when they are available. However, because many developing countries have small and immature electricity grids, the currently available Generation III(+) reactors may be unsuitable since they are too large, too expensive, and too complex. Therefore, GNEP envisions new types of reactors that must be developed for international deployment that are "right sized" for the developing countries and that are based on technologies, designs, and policies focused on reducing proliferation risk. The first step in developing such systems is the generation of technical requirements that will ensure that the systems meet both the GNEP policy goals and the power needs of the recipient countries. REQUIREMENTS Reactor systems deployed internationally within the GNEP context must meet a number of requirements similar to the safety, reliability, economics, and proliferation goals established for the DOE Generation IV program. Because of the emphasis on deployment to nonnuclear developing countries, the requirements will be weighted differently than with Generation IV, especially regarding safety and non-proliferation goals. Also, the reactors should be sized for market conditions in developing countries where energy demand per capita, institutional maturity

47 CFR 80.275 - Technical Requirements for Class A Automatic Identification System (AIS) equipment.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 5 2010-10-01 2010-10-01 false Technical Requirements for Class A Automatic Identification System (AIS) equipment. 80.275 Section 80.275 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES STATIONS IN THE MARITIME SERVICES Equipment Authorization for Compulsory Ships § 80.275...

14 CFR 171.47 - Performance requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Performance requirements. 171.47 Section 171.47 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... Performance requirements. (a) The Instrument Landing System must perform in accordance with the “International...

14 CFR 171.47 - Performance requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Performance requirements. 171.47 Section 171.47 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... Performance requirements. (a) The Instrument Landing System must perform in accordance with the “International...

14 CFR 171.47 - Performance requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Performance requirements. 171.47 Section 171.47 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... Performance requirements. (a) The Instrument Landing System must perform in accordance with the “International...

14 CFR 171.47 - Performance requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Performance requirements. 171.47 Section 171.47 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... Performance requirements. (a) The Instrument Landing System must perform in accordance with the “International...

14 CFR 171.47 - Performance requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Performance requirements. 171.47 Section 171.47 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... Performance requirements. (a) The Instrument Landing System must perform in accordance with the “International...

White Paper: Landscape on Technical and Conceptual Requirements and Competence Framework in Drug/Disease Modeling and Simulation

PubMed Central

Vlasakakis, G; Comets, E; Keunecke, A; Gueorguieva, I; Magni, P; Terranova, N; Della Pasqua, O; de Lange, E C; Kloft, C

2013-01-01

Pharmaceutical sciences experts and regulators acknowledge that pharmaceutical development as well as drug usage requires more than scientific advancements to cope with current attrition rates/therapeutic failures. Drug disease modeling and simulation (DDM&S) creates a paradigm to enable an integrated and higher-level understanding of drugs, (diseased)systems, and their interactions (systems pharmacology) through mathematical/statistical models (pharmacometrics)1—hence facilitating decision making during drug development and therapeutic usage of medicines. To identify gaps and challenges in DDM&S, an inventory of skills and competencies currently available in academia, industry, and clinical practice was obtained through survey. The survey outcomes revealed benefits, weaknesses, and hurdles for the implementation of DDM&S. In addition, the survey indicated that no consensus exists about the knowledge, skills, and attributes required to perform DDM&S activities effectively. Hence, a landscape of technical and conceptual requirements for DDM&S was identified and serves as a basis for developing a framework of competencies to guide future education and training in DDM&S. PMID:23887723

Engineering directorate technical facilities catalog

NASA Technical Reports Server (NTRS)

Maloy, Joseph E.

1993-01-01

The Engineering Directorate Technical Facilities Catalog is designed to provide an overview of the technical facilities available within the Engineering Directorate at the National Aeronautics and Space Administration (NASA), Lyndon B. Johnson Space Center (JSC) in Houston, Texas. The combined capabilities of these engineering facilities are essential elements of overall JSC capabilities required to manage and perform major NASA engineering programs. The facilities are grouped in the text by chapter according to the JSC division responsible for operation of the facility. This catalog updates the facility descriptions for the JSC Engineering Directorate Technical Facilities Catalog, JSC 19295 (August 1989), and supersedes the Engineering Directorate, Principle test and Development Facilities, JSC, 19962 (November 1984).

49 CFR 171.24 - Additional requirements for the use of the ICAO Technical Instructions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Additional requirements for the use of the ICAO... the United States by aircraft, and by motor vehicle or rail either before or after being transported by aircraft in accordance with the ICAO Technical Instructions (IBR, see § 171.7), as authorized in...

14 CFR 171.7 - Performance requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Performance requirements. 171.7 Section 171.7 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) NAVIGATIONAL FACILITIES NON-FEDERAL NAVIGATION FACILITIES VOR Facilities § 171.7 Performance requirements. (a...

14 CFR 171.7 - Performance requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Performance requirements. 171.7 Section 171.7 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) NAVIGATIONAL FACILITIES NON-FEDERAL NAVIGATION FACILITIES VOR Facilities § 171.7 Performance requirements. (a...

14 CFR 171.7 - Performance requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Performance requirements. 171.7 Section 171.7 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) NAVIGATIONAL FACILITIES NON-FEDERAL NAVIGATION FACILITIES VOR Facilities § 171.7 Performance requirements. (a...

14 CFR 171.7 - Performance requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Performance requirements. 171.7 Section 171.7 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) NAVIGATIONAL FACILITIES NON-FEDERAL NAVIGATION FACILITIES VOR Facilities § 171.7 Performance requirements. (a...

Discovering system requirements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bahill, A.T.; Bentz, B.; Dean, F.F.

1996-07-01

Cost and schedule overruns are often caused by poor requirements that are produced by people who do not understand the requirements process. This report provides a high-level overview of the system requirements process, explaining types, sources, and characteristics of good requirements. System requirements, however, are seldom stated by the customer. Therefore, this report shows ways to help you work with your customer to discover the system requirements. It also explains terminology commonly used in the requirements development field, such as verification, validation, technical performance measures, and the various design reviews.

Assessing technical performance in differential gene expression experiments with external spike-in RNA control ratio mixtures.

PubMed

Munro, Sarah A; Lund, Steven P; Pine, P Scott; Binder, Hans; Clevert, Djork-Arné; Conesa, Ana; Dopazo, Joaquin; Fasold, Mario; Hochreiter, Sepp; Hong, Huixiao; Jafari, Nadereh; Kreil, David P; Łabaj, Paweł P; Li, Sheng; Liao, Yang; Lin, Simon M; Meehan, Joseph; Mason, Christopher E; Santoyo-Lopez, Javier; Setterquist, Robert A; Shi, Leming; Shi, Wei; Smyth, Gordon K; Stralis-Pavese, Nancy; Su, Zhenqiang; Tong, Weida; Wang, Charles; Wang, Jian; Xu, Joshua; Ye, Zhan; Yang, Yong; Yu, Ying; Salit, Marc

2014-09-25

There is a critical need for standard approaches to assess, report and compare the technical performance of genome-scale differential gene expression experiments. Here we assess technical performance with a proposed standard 'dashboard' of metrics derived from analysis of external spike-in RNA control ratio mixtures. These control ratio mixtures with defined abundance ratios enable assessment of diagnostic performance of differentially expressed transcript lists, limit of detection of ratio (LODR) estimates and expression ratio variability and measurement bias. The performance metrics suite is applicable to analysis of a typical experiment, and here we also apply these metrics to evaluate technical performance among laboratories. An interlaboratory study using identical samples shared among 12 laboratories with three different measurement processes demonstrates generally consistent diagnostic power across 11 laboratories. Ratio measurement variability and bias are also comparable among laboratories for the same measurement process. We observe different biases for measurement processes using different mRNA-enrichment protocols.

47 CFR 76.1608 - System technical integration requiring uniform election of must-carry or retransmission consent...

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 4 2014-10-01 2014-10-01 false System technical integration requiring uniform election of must-carry or retransmission consent status. 76.1608 Section 76.1608 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES MULTICHANNEL VIDEO AND CABLE TELEVISION SERVICE...

47 CFR 76.1608 - System technical integration requiring uniform election of must-carry or retransmission consent...

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 4 2011-10-01 2011-10-01 false System technical integration requiring uniform election of must-carry or retransmission consent status. 76.1608 Section 76.1608 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES MULTICHANNEL VIDEO AND CABLE TELEVISION SERVICE...

47 CFR 76.1608 - System technical integration requiring uniform election of must-carry or retransmission consent...

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 4 2013-10-01 2013-10-01 false System technical integration requiring uniform election of must-carry or retransmission consent status. 76.1608 Section 76.1608 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES MULTICHANNEL VIDEO AND CABLE TELEVISION SERVICE...

47 CFR 76.1608 - System technical integration requiring uniform election of must-carry or retransmission consent...

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 4 2012-10-01 2012-10-01 false System technical integration requiring uniform election of must-carry or retransmission consent status. 76.1608 Section 76.1608 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES MULTICHANNEL VIDEO AND CABLE TELEVISION SERVICE...

47 CFR 76.1608 - System technical integration requiring uniform election of must-carry or retransmission consent...

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false System technical integration requiring uniform election of must-carry or retransmission consent status. 76.1608 Section 76.1608 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST RADIO SERVICES MULTICHANNEL VIDEO AND CABLE TELEVISION SERVICE...

Integrated Requirements Analysis and Technology Roadmaps

NASA Technical Reports Server (NTRS)

1997-01-01

In fiscal year 1997, Strategic Insight performed analytical studies for NASA's Highly Reusable Space Transportation (HRST) program, creating program documents which illuminated technical requirements and critical research opportunities. Studies were performed to structure and confirm HRST's evolving technical requirements, building on Marshall's Phase 1 work, which defined HRST system concepts, analytical tools and high-level issues for assessment in Phase 2. Specifically, Strategic Insight: (1) Performed a requirements analysis to update HRST: An Advanced Concepts Study, Study Guidelines, Version 2.0 of January 22, 1996; only minor changes were recommended for the given parameters of interest to concept designers; (2) Conducted mini-workshops during HRST Working Group meetings on April 14-15, 1997 and July 22-24, 1997; and (3) Created structures for technology road maps of candidate HRST concepts, both subsystem and end-to-end concepts, emerging from the 13 cooperative agreement projects.

Coaching Non-technical Skills Improves Surgical Residents' Performance in a Simulated Operating Room.

PubMed

Yule, Steven; Parker, Sarah Henrickson; Wilkinson, Jill; McKinley, Aileen; MacDonald, Jamie; Neill, Adrian; McAdam, Tim

2015-01-01

To investigate the effect of coaching on non-technical skills and performance during laparoscopic cholecystectomy in a simulated operating room (OR). Non-technical skills (situation awareness, decision making, teamwork, and leadership) underpin technical ability and are critical to the success of operations and the safety of patients in the OR. The rate of developing assessment tools in this area has outpaced development of workable interventions to improve non-technical skills in surgical training and beyond. A randomized trial was conducted with senior surgical residents (n = 16). Participants were randomized to receive either non-technical skills coaching (intervention) or to self-reflect (control) after each of 5 simulated operations. Coaching was based on the Non-Technical Skills For Surgeons (NOTSS) behavior observation system. Surgeon-coaches trained in this method coached participants in the intervention group for 10 minutes after each simulation. Primary outcome measure was non-technical skills, assessed from video by a surgeon using the NOTSS system. Secondary outcomes were time to call for help during bleeding, operative time, and path length of laparoscopic instruments. Non-technical skills improved in the intervention group from scenario 1 to scenario 5 compared with those in the control group (p = 0.04). The intervention group was faster to call for help when faced with unstoppable bleeding in the final scenario (no. 5; p = 0.03). Coaching improved residents' non-technical skills in the simulated OR compared with those in the control group. Important next steps are to implement non-technical skills coaching in the real OR and assess effect on clinically important process measures and patient outcomes. Copyright © 2015 Association of Program Directors in Surgery. Published by Elsevier Inc. All rights reserved.

Quantitative Imaging Biomarkers: A Review of Statistical Methods for Technical Performance Assessment

PubMed Central

2017-01-01

Technological developments and greater rigor in the quantitative measurement of biological features in medical images have given rise to an increased interest in using quantitative imaging biomarkers (QIBs) to measure changes in these features. Critical to the performance of a QIB in preclinical or clinical settings are three primary metrology areas of interest: measurement linearity and bias, repeatability, and the ability to consistently reproduce equivalent results when conditions change, as would be expected in any clinical trial. Unfortunately, performance studies to date differ greatly in designs, analysis method and metrics used to assess a QIB for clinical use. It is therefore, difficult or not possible to integrate results from different studies or to use reported results to design studies. The Radiological Society of North America (RSNA) and the Quantitative Imaging Biomarker Alliance (QIBA) with technical, radiological and statistical experts developed a set of technical performance analysis methods, metrics and study designs that provide terminology, metrics and methods consistent with widely accepted metrological standards. This document provides a consistent framework for the conduct and evaluation of QIB performance studies so that results from multiple studies can be compared, contrasted or combined. PMID:24919831

42 CFR 493.1409 - Condition: Laboratories performing moderate complexity testing; technical consultant.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 5 2010-10-01 2010-10-01 false Condition: Laboratories performing moderate complexity testing; technical consultant. 493.1409 Section 493.1409 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) STANDARDS AND CERTIFICATION...

42 CFR 493.1409 - Condition: Laboratories performing moderate complexity testing; technical consultant.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 5 2011-10-01 2011-10-01 false Condition: Laboratories performing moderate complexity testing; technical consultant. 493.1409 Section 493.1409 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) STANDARDS AND CERTIFICATION...

[The study of establishment of the " Chinese provincial Blindness prevention technical guidance group performance evaluation system"].

PubMed

Lu, L N; He, X G; Zhu, J F; Xu, X; Zhang, R; Hu, X; Zou, H D

2016-11-11

Objective: To establish an assessment system, including indexes and scoring methods, that can be used for performance evaluation of the provincial blindness prevention technical guidance group properly and effectively . Methods: The indexes and scoring methods were set based on the core content of The " National Plan of Prevention and Treatment of Blindness (2012-2015)" , the specific requirement and target of the World Health Organization (WHO) "For the General Eye Health: Global plan of Action (2014-2019)" , and the current situation of the China's provinces and autonomous regions. These indexes should be of effectiveness, feasibility, comparability, guidance and advancing. Formed by a literature review of candidate indicators, the framework of the system is built by qualitative assessment. With the Delphi method, the system was further revised and improved. Empirical pilot study was then used to prove the feasibility, followed by the final qualitative analysis that establish the " Chinese provincial Blindness prevention technical guidance group performance evaluation system" . Results: Through the literature review and qualitative assessment, a six dimensional system framework was built, including 6 first-level indicators, 16 second-level indicators, and 29 third-level indicators through Delphi method evaluation. With the variation coefficient method, the coeffiences of the first-level index weight were calculated as: Organization and management 0.15, Development and implementation of blindness prevention plans 0.15, Implementation of blindness prevention projects 0.14, Training 0.17, Health education 0.18, and Cooperation and exchanges 0.21. The specific scoring method for this system is confirmed as: data and files check, field interview, and record interview, sampling investigation. Empirical pilot study was conducted in the Jilin, Guizhou and Gansu provinces, and the self-assessment results from local experts were consistent with the scores from the systems

Shuttle ku-band communications/radar technical concepts

NASA Technical Reports Server (NTRS)

Griffin, J. W.; Kelley, J. S.; Steiner, A. W.; Vang, H. A.; Zrubek, W. E.; Huth, G. K.

1985-01-01

Technical data on the Shuttle Orbiter K sub u-band communications/radar system are presented. The more challenging aspects of the system design and development are emphasized. The technical problems encountered and the advancements made in solving them are discussed. The radar functions are presented first. Requirements and design/implementation approaches are discussed. Advanced features are explained, including Doppler measurement, frequency diversity, multiple pulse repetition frequencies and pulse widths, and multiple modes. The communications functions that are presented include advances made because of the requirements for multiple communications modes. Spread spectrum, quadrature phase shift keying (QPSK), variable bit rates, and other advanced techniques are discussed. Performance results and conclusions reached are outlined.

42 CFR 493.1447 - Condition: Laboratories performing high complexity testing; technical supervisor.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 5 2011-10-01 2011-10-01 false Condition: Laboratories performing high complexity testing; technical supervisor. 493.1447 Section 493.1447 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) STANDARDS AND CERTIFICATION LABORATORY...

42 CFR 493.1447 - Condition: Laboratories performing high complexity testing; technical supervisor.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 5 2010-10-01 2010-10-01 false Condition: Laboratories performing high complexity testing; technical supervisor. 493.1447 Section 493.1447 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) STANDARDS AND CERTIFICATION LABORATORY...

Meta-analysis of the technical performance of an imaging procedure: guidelines and statistical methodology.

PubMed

Huang, Erich P; Wang, Xiao-Feng; Choudhury, Kingshuk Roy; McShane, Lisa M; Gönen, Mithat; Ye, Jingjing; Buckler, Andrew J; Kinahan, Paul E; Reeves, Anthony P; Jackson, Edward F; Guimaraes, Alexander R; Zahlmann, Gudrun

2015-02-01

Medical imaging serves many roles in patient care and the drug approval process, including assessing treatment response and guiding treatment decisions. These roles often involve a quantitative imaging biomarker, an objectively measured characteristic of the underlying anatomic structure or biochemical process derived from medical images. Before a quantitative imaging biomarker is accepted for use in such roles, the imaging procedure to acquire it must undergo evaluation of its technical performance, which entails assessment of performance metrics such as repeatability and reproducibility of the quantitative imaging biomarker. Ideally, this evaluation will involve quantitative summaries of results from multiple studies to overcome limitations due to the typically small sample sizes of technical performance studies and/or to include a broader range of clinical settings and patient populations. This paper is a review of meta-analysis procedures for such an evaluation, including identification of suitable studies, statistical methodology to evaluate and summarize the performance metrics, and complete and transparent reporting of the results. This review addresses challenges typical of meta-analyses of technical performance, particularly small study sizes, which often causes violations of assumptions underlying standard meta-analysis techniques. Alternative approaches to address these difficulties are also presented; simulation studies indicate that they outperform standard techniques when some studies are small. The meta-analysis procedures presented are also applied to actual [18F]-fluorodeoxyglucose positron emission tomography (FDG-PET) test-retest repeatability data for illustrative purposes. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Meta-analysis of the technical performance of an imaging procedure: Guidelines and statistical methodology

PubMed Central

Huang, Erich P; Wang, Xiao-Feng; Choudhury, Kingshuk Roy; McShane, Lisa M; Gönen, Mithat; Ye, Jingjing; Buckler, Andrew J; Kinahan, Paul E; Reeves, Anthony P; Jackson, Edward F; Guimaraes, Alexander R; Zahlmann, Gudrun

2017-01-01

Medical imaging serves many roles in patient care and the drug approval process, including assessing treatment response and guiding treatment decisions. These roles often involve a quantitative imaging biomarker, an objectively measured characteristic of the underlying anatomic structure or biochemical process derived from medical images. Before a quantitative imaging biomarker is accepted for use in such roles, the imaging procedure to acquire it must undergo evaluation of its technical performance, which entails assessment of performance metrics such as repeatability and reproducibility of the quantitative imaging biomarker. Ideally, this evaluation will involve quantitative summaries of results from multiple studies to overcome limitations due to the typically small sample sizes of technical performance studies and/or to include a broader range of clinical settings and patient populations. This paper is a review of meta-analysis procedures for such an evaluation, including identification of suitable studies, statistical methodology to evaluate and summarize the performance metrics, and complete and transparent reporting of the results. This review addresses challenges typical of meta-analyses of technical performance, particularly small study sizes, which often causes violations of assumptions underlying standard meta-analysis techniques. Alternative approaches to address these difficulties are also presented; simulation studies indicate that they outperform standard techniques when some studies are small. The meta-analysis procedures presented are also applied to actual [18F]-fluorodeoxyglucose positron emission tomography (FDG-PET) test–retest repeatability data for illustrative purposes. PMID:24872353

50 CFR 660.15 - Equipment requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... receivers, computer hardware for electronic fish ticket software and computer hardware for electronic logbook software. (b) Performance and technical requirements for scales used to weigh catch at sea... ticket software provided by Pacific States Marine Fish Commission are required to meet the hardware and...

Performance Evaluation of Technical Institutions: An Application of Data Envelopment Analysis

ERIC Educational Resources Information Center

Debnath, Roma Mitra; Shankar, Ravi; Kumar, Surender

2008-01-01

Technical institutions (TIs) are playing an important role in making India a knowledge hub of this century. There is still great diversity in their relative performance, which is a matter of concern to the education planner. This article employs the method of data envelopment analysis (DEA) to compare the relative efficiency of TIs in India. The…

Supervision by a technically qualified surgeon affects the proficiency and safety of laparoscopic colectomy performed by novice surgeons.

PubMed

Ichikawa, Nobuki; Homma, Shigenori; Yoshida, Tadashi; Ohno, Yosuke; Kawamura, Hideki; Kamiizumi, You; Iijima, Hiroaki; Taketomi, Akinobu

2018-01-01

The use of laparoscopic colectomy is becoming widespread and acquisition of its technique is challenging. In this study, we investigated whether supervision by a technically qualified surgeon affects the proficiency and safety of laparoscopic colectomy performed by novice surgeons. The outcomes of 23 right colectomies and 19 high anterior resections for colon cancers performed by five novice surgeons (experience level of <10 cases) between 2014 and 2016 were assessed. A laparoscopic surgeon qualified by the Endoscopic Surgical Skill Qualification System (Japan Society for Endoscopic Surgery) participated in surgeries as the teaching assistant. In the right colectomy group, one patient (4.3%) required conversion to open surgery and postoperative morbidities occurred in two cases (8.6%). The operative time moving average gradually decreased from 216 to 150 min, and the blood loss decreased from 128 to 28 mL. In the CUSUM charts, the values for operative time decreased continuously after the 18th case, as compared to the Japanese standard. The values for blood loss also plateaued after the 18th case. In the high anterior resection group, one patient (5.2%) required conversion to open surgery and no postoperative complication occurred in any patient. The operative time moving average gradually decreased from 258 to 228 min, and the blood loss decreased from 33 to 18 mL. The CUSUM charts showed that the values of operative time plateaued after the 18th case, as compared to the Japanese standard. In the CUSUM chart for blood loss, no distinguishing peak or trend was noted. Supervision by a technically qualified surgeon affects the proficiency and safety of laparoscopic colectomy performed by novice surgeons. The trainee's learning curve in this study represents successful mentoring by the laparoscopic surgeon qualified by the Endoscopic Surgical Skill Qualification System.

[Implementation of the technical requirements of the UNE-EN-ISO 15189 quality standard in a mycobacterial laboratory].

PubMed

Guna Serrano, M del Remedio; Ocete Mochón, M Dolores; Lahiguera, M José; Bresó, M Carmen; Gimeno Cardona, Concepción

2013-02-01

The UNE-EN-ISO 15189:2007 standard defines the requirements for quality and competence that must be met by medical laboratories. These laboratories should use this international standard to develop their own quality management systems and to evaluate their own competencies; in turn, this standard will be used by accreditation bodies to confirm or recognize the laboratories' competence. In clinical microbiology laboratories, application of the standard implies the implementation of the technical and specific management requirements that must be met to achieve optimal quality when carrying out microbiological tests. In Spain, accreditation is granted by the Spanish Accreditation Body (Entidad Nacional de Acreditación). This review aims to discuss the practical application of the standard's technical requirements in mycobacterial laboratory. Firstly, we define the scope of accreditation. Secondly, we specify how the items of the standard on personnel management, control of equipment, environmental facilities, method validation, internal controls and customer satisfaction surveys were developed and implemented in our laboratory. Copyright © 2013 Elsevier España, S.L. All rights reserved.

Testing the performance of technical trading rules in the Chinese markets based on superior predictive test

NASA Astrophysics Data System (ADS)

Wang, Shan; Jiang, Zhi-Qiang; Li, Sai-Ping; Zhou, Wei-Xing

2015-12-01

Technical trading rules have a long history of being used by practitioners in financial markets. The profitable ability and efficiency of technical trading rules are yet controversial. In this paper, we test the performance of more than seven thousand traditional technical trading rules on the Shanghai Securities Composite Index (SSCI) from May 21, 1992 through June 30, 2013 and China Securities Index 300 (CSI 300) from April 8, 2005 through June 30, 2013 to check whether an effective trading strategy could be found by using the performance measurements based on the return and Sharpe ratio. To correct for the influence of the data-snooping effect, we adopt the Superior Predictive Ability test to evaluate if there exists a trading rule that can significantly outperform the benchmark. The result shows that for SSCI, technical trading rules offer significant profitability, while for CSI 300, this ability is lost. We further partition the SSCI into two sub-series and find that the efficiency of technical trading in sub-series, which have exactly the same spanning period as that of CSI 300, is severely weakened. By testing the trading rules on both indexes with a five-year moving window, we find that during the financial bubble from 2005 to 2007, the effectiveness of technical trading rules is greatly improved. This is consistent with the predictive ability of technical trading rules which appears when the market is less efficient.

Effects of Performance-Based Financial Incentives on Work Performance: A Study of Technical-Level Employees in the Private Sector in Sri Lanka

ERIC Educational Resources Information Center

Wickramasinghe, Vathsala; Dabere, Sampath

2012-01-01

The objective of the study is to investigate the effect of performance-based financial incentives on work performance. The study hypothesized that the design features of performance-based financial incentive schemes themselves may influence individuals' work performance. For the study, survey methodology was used and 93 technical-level employees…

Simulator training and non-technical factors improve laparoscopic performance among OBGYN trainees.

PubMed

Ahlborg, Liv; Hedman, Leif; Nisell, Henry; Felländer-Tsai, Li; Enochsson, Lars

2013-10-01

To investigate how simulator training and non-technical factors affect laparoscopic performance among residents in obstetrics and gynecology. In this prospective study, trainees were randomized into three groups. The first group was allocated to proficiency-based training in the LapSimGyn(®) virtual reality simulator. The second group received additional structured mentorship during subsequent laparoscopies. The third group served as control group. At baseline an operation was performed and visuospatial ability, flow and self-efficacy were assessed. All groups subsequently performed three tubal occlusions. Self-efficacy and flow were assessed before and/or after each operation. Simulator training was conducted at the Center for Advanced Medical Simulation and Training, Karolinska University Hospital. Sterilizations were performed at each trainee's home clinic. Twenty-eight trainees/residents from 21 hospitals in Sweden were included. Visuospatial ability was tested by the Mental Rotation Test-A. Flow and self-efficacy were assessed by validated scales and questionnaires. Laparoscopic performance was measured as the duration of surgery. Visuospatial ability, self-efficacy and flow were correlated to the laparoscopic performance using Spearman's correlations. Differences between groups were analyzed by the Mann-Whitney U-test. No differences across groups were detected at baseline. Self-efficacy scores before and flow scores after the third operation were significantly higher in the trained groups. Duration of surgery was significantly shorter in the trained groups. Flow and self-efficacy correlate positively with laparoscopic performance. Simulator training and non-technical factors appear to improve the laparoscopic performance among trainees/residents in obstetrics and gynecology. © 2013 Nordic Federation of Societies of Obstetrics and Gynecology.

Quantitative imaging biomarkers: a review of statistical methods for technical performance assessment.

PubMed

Raunig, David L; McShane, Lisa M; Pennello, Gene; Gatsonis, Constantine; Carson, Paul L; Voyvodic, James T; Wahl, Richard L; Kurland, Brenda F; Schwarz, Adam J; Gönen, Mithat; Zahlmann, Gudrun; Kondratovich, Marina V; O'Donnell, Kevin; Petrick, Nicholas; Cole, Patricia E; Garra, Brian; Sullivan, Daniel C

2015-02-01

Technological developments and greater rigor in the quantitative measurement of biological features in medical images have given rise to an increased interest in using quantitative imaging biomarkers to measure changes in these features. Critical to the performance of a quantitative imaging biomarker in preclinical or clinical settings are three primary metrology areas of interest: measurement linearity and bias, repeatability, and the ability to consistently reproduce equivalent results when conditions change, as would be expected in any clinical trial. Unfortunately, performance studies to date differ greatly in designs, analysis method, and metrics used to assess a quantitative imaging biomarker for clinical use. It is therefore difficult or not possible to integrate results from different studies or to use reported results to design studies. The Radiological Society of North America and the Quantitative Imaging Biomarker Alliance with technical, radiological, and statistical experts developed a set of technical performance analysis methods, metrics, and study designs that provide terminology, metrics, and methods consistent with widely accepted metrological standards. This document provides a consistent framework for the conduct and evaluation of quantitative imaging biomarker performance studies so that results from multiple studies can be compared, contrasted, or combined. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Estimation of Managerial and Technical Personnel Requirements in Selected Industries. Training for Industry Series, No. 2.

ERIC Educational Resources Information Center

United Nations Industrial Development Organization, Vienna (Austria).

The need to develop managerial and technical personnel in the cement, fertilizer, pulp and paper, sugar, leather and shoe, glass, and metal processing industries of various nations was studied, with emphasis on necessary steps in developing nations to relate occupational requirements to technology, processes, and scale of output. Estimates were…

Consensus statement for use and technical requirements of thyroid ultrasound in endocrinology units.

PubMed

Martín-Hernández, Tomás; Díez Gómez, Juan José; Díaz-Soto, Gonzalo; Torres Cuadro, Alberto; Navarro González, Elena; Oleaga Alday, Amelia; Sambo Salas, Marcel; Reverter Calatayud, Jordi L; Argüelles Jiménez, Iñaki; Mancha Doblas, Isabel; Fernández García, Diego; Galofré, Juan Carlos

2017-03-01

Thyroid nodule detection has increased with widespread use of ultrasound, which is currently the main tool for detection, monitoring, diagnosis and, in some instances, treatment of thyroid nodules. Knowledge of ultrasound and adequate instruction on its use require a position statement by the scientific societies concerned. The working groups on thyroid cancer and ultrasound techniques of the Spanish Society of Endocrinology and Nutrition have promoted this document, based on a thorough analysis of the current literature, the results of multicenter studies and expert consensus, in order to set the requirements for the best use of ultrasound in clinical practice. The objectives include the adequate framework for use of thyroid ultrasound, the technical and legal requirements, the clinical situations in which it is recommended, the levels of knowledge and learning processes, the associated responsibility, and the establishment of a standardized reporting of results and integration into hospital information systems and endocrinology units. Copyright © 2017 SEEN. Publicado por Elsevier España, S.L.U. All rights reserved.

Conceptual design of a moving belt radiator shuttle-attached experiments: Technical requirement Document

NASA Technical Reports Server (NTRS)

Aguilar, Jerry L.

1989-01-01

The technical requirements for a shuttle-attached Moving Belt Radiator (MBR) experiment are defined. The MBR is an advanced radiator concept in which a rotating belt radiates thermal energy to space. The requirements for integrating the MBR experiment in the shuttle bay are discussed. Requirements for the belt material and working fluid are outlined along with some possible options. The proposed size and relationship to a full scale Moving Belt Radiator are defined. The experiment is defined with the primary goal of dynamic testing and a secondary goal of demonstrating the sealing and heat transfer characteristics. A perturbation system which will simulate a docking maneuver or other type of short term acceleration is proposed for inclusion in the experimental apparatus. A deployment and retraction capability which will aid in evaluating the dynamics of a belt during such a maneuver is also described. The proposed test sequence for the experiment is presented. Details of the conceptual design are not presented herein, but rather in a separate Final Report.

Minimally Invasive Implantable Fetal Micropacemaker: Mechanical Testing and Technical Refinements

PubMed Central

Zhou, Li; Vest, Adriana N.; Peck, Raymond A.; Sredl, Jonathan P.; Huang, Xuechen; Bar-Cohen, Yaniv; Silka, Michael J.; Pruetz, Jay D.; Chmait, Ramen H.; Loeb, Gerald E.

2016-01-01

This paper discusses the technical and safety requirements for cardiac pacing of a human fetus with heart failure and hydrops fetalis secondary to complete heart block. Engineering strategies to meet specific technical requirements were integrated into a systematic design and implementation consisting of a novel fetal micropacemaker, a percutaneous implantation system, and a sterile package that enables device storage and recharging maintenance in a clinical setting. We further analyzed observed problems on myocardial fixation and pacing lead fatigue previously reported in earlier preclinical trials. This paper describes the technical refinements of the implantable fetal micropacemaker to overcome these challenges. The mechanical performance has been extensively tested to verify the improvement of reliability and safety margins of the implantation system. PMID:27021067

46 CFR 160.066-7 - Performance requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 6 2012-10-01 2012-10-01 false Performance requirements. 160.066-7 Section 160.066-7 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS....066-7 Performance requirements. (a) Each signal must: (1) Burn “vivid red” when tested as specified in...

46 CFR 160.066-7 - Performance requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Performance requirements. 160.066-7 Section 160.066-7 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS....066-7 Performance requirements. (a) Each signal must: (1) Burn “vivid red” when tested as specified in...

46 CFR 160.066-7 - Performance requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Performance requirements. 160.066-7 Section 160.066-7 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS....066-7 Performance requirements. (a) Each signal must: (1) Burn “vivid red” when tested as specified in...

32 CFR 37.895 - How is the final performance report to be sent to the Defense Technical Information Center?

Code of Federal Regulations, 2014 CFR

2014-07-01

... How is the final performance report to be sent to the Defense Technical Information Center? (a... 32 National Defense 1 2014-07-01 2014-07-01 false How is the final performance report to be sent to the Defense Technical Information Center? 37.895 Section 37.895 National Defense Department of...

32 CFR 37.895 - How is the final performance report to be sent to the Defense Technical Information Center?

Code of Federal Regulations, 2011 CFR

2011-07-01

... How is the final performance report to be sent to the Defense Technical Information Center? (a... 32 National Defense 1 2011-07-01 2011-07-01 false How is the final performance report to be sent to the Defense Technical Information Center? 37.895 Section 37.895 National Defense Department of...

32 CFR 37.895 - How is the final performance report to be sent to the Defense Technical Information Center?

Code of Federal Regulations, 2013 CFR

2013-07-01

... How is the final performance report to be sent to the Defense Technical Information Center? (a... 32 National Defense 1 2013-07-01 2013-07-01 false How is the final performance report to be sent to the Defense Technical Information Center? 37.895 Section 37.895 National Defense Department of...

32 CFR 37.895 - How is the final performance report to be sent to the Defense Technical Information Center?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 1 2012-07-01 2012-07-01 false How is the final performance report to be sent to the Defense Technical Information Center? 37.895 Section 37.895 National Defense Department of... How is the final performance report to be sent to the Defense Technical Information Center? (a...

40 CFR 63.504 - Additional requirements for performance testing.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Additional requirements for performance... Additional requirements for performance testing. (a) Performance testing shall be conducted in accordance.... Sections 63.484 through 63.501 also contain specific testing requirements. (1) Performance tests shall be...

Technical and Tactical Aspects that Differentiate Winning and Losing Performances in Elite Male Karate Fighters.

PubMed

Vidranski, Tihomir; Sertić, Hrvoje; Jukić, Josefina

2015-07-01

The purpose of this research was to identify the fighters' technical and tactical activity indicators in order to determine indicator significance regarding situational efficiency and designation between winning and losing performances in a karate match. We scientifically observed a sample of 274 male contesters of 137 karate matches during the 2008 World Karate Championship in Tokyo. Each individual competitor was observed in maximum of three matches. The matches were recorded using a DVD camera in order to collect data for further analysis, and the sample was further described using 48 technical and tactical indicators of situational efficiency and match outcome variables. The obtained results indicate that a karate match is composed of 91% of non-scoring techniques and 9% of scoring techniques in the total technique frequency. On this basis a significant difference in the situational efficiency between the match winners and the losing contesters has been discovered. Those two groups of fighters exhibit a statistically significant difference (p<0.05) in 11 out of 21 observed variables of situational efficiency in the table of derived situational indicators. A prevalence of non-scoring techniques suggests that energy demand and technical and tactical requirements of a karate match are in the largest extent defined by non-scoring techniques. Therefore, it would be a grave mistake to disregard non-scoring karate techniques in any future situational efficiency studies. It has been discovered that the winners differ from the defeated contesters by a higher level of situational efficiency in their executed techniques, which incorporate versatility, biomechanical and structural complexity, topological diversity and a specific tactical concept of technique use in the attack phase.

Simulation fails to replicate stress in trainees performing a technical procedure in the clinical environment.

PubMed

Baker, B G; Bhalla, A; Doleman, B; Yarnold, E; Simons, S; Lund, J N; Williams, J P

2017-01-01

Simulation-based training (SBT) has become an increasingly important method by which doctors learn. Stress has an impact upon learning, performance, technical, and non-technical skills. However, there are currently no studies that compare stress in the clinical and simulated environment. We aimed to compare objective (heart rate variability, HRV) and subjective (state trait anxiety inventory, STAI) measures of stress theatre with a simulated environment. HRV recordings were obtained from eight anesthetic trainees performing an uncomplicated rapid sequence induction at pre-determined procedural steps using a wireless Polar RS800CX monitor © in an emergency theatre setting. This was repeated in the simulated environment. Participants completed an STAI before and after the procedure. Eight trainees completed the study. The theatre environment caused an increase in objective stress vs baseline (p = .004). There was no significant difference between average objective stress levels across all time points (p = .20) between environments. However, there was a significant interaction between the variables of objective stress and environment (p = .045). There was no significant difference in subjective stress (p = .27) between environments. Simulation was unable to accurately replicate the stress of the technical procedure. This is the first study that compares the stress during SBT with the theatre environment and has implications for the assessment of simulated environments for use in examinations, rating of technical and non-technical skills, and stress management training.

NASA Aerospace Flight Battery Program: Recommendations for Technical Requirements for Inclusion in Aerospace Battery Procurements. Volume 1, Part 2

NASA Technical Reports Server (NTRS)

Jung, David S.; Manzo, Michelle A.

2010-01-01

This NASA Aerospace Flight Battery Systems Working Group was chartered within the NASA Engineering and Safety Center (NESC). The Battery Working Group was tasked to complete tasks and to propose proactive work to address battery related, agency-wide issues on an annual basis. In its first year of operation, this proactive program addressed various aspects of the validation and verification of aerospace battery systems for NASA missions. Studies were performed, issues were discussed and in many cases, test programs were executed to generate recommendations and guidelines to reduce risk associated with various aspects of implementing battery technology in the aerospace industry. This document contains Part 2 - Volume I: Recommendations for Technical Requirements for Inclusion in Aerospace Battery Procurements of the program's operations.

Traceability of Software Safety Requirements in Legacy Safety Critical Systems

NASA Technical Reports Server (NTRS)

Hill, Janice L.

2007-01-01

How can traceability of software safety requirements be created for legacy safety critical systems? Requirements in safety standards are imposed most times during contract negotiations. On the other hand, there are instances where safety standards are levied on legacy safety critical systems, some of which may be considered for reuse for new applications. Safety standards often specify that software development documentation include process-oriented and technical safety requirements, and also require that system and software safety analyses are performed supporting technical safety requirements implementation. So what can be done if the requisite documents for establishing and maintaining safety requirements traceability are not available?

A Technical Overview and Description of SOFIA (Stratospheric Observatory for Infrared Astronomy)

NASA Technical Reports Server (NTRS)

Kunz, Nans

2003-01-01

This paper provides a technical overview of SOFIA, a unique airborne observatory, from an engineering perspective. It will do this by describing several of the systems of this observatory that are common with mountain top ground based observatories but mostly emphasize those more unique features and systems that are required to facilitate world class astronomy from a highly modified Boeing 747-SP flying at Mach 0.84 in the Stratosphere. This paper provides a technical overview of SOFIA by reviewing each of the performance specifications (the level one requirements for development) and describing some of the technical advancements for the telescope as well as the platform required to achieve these performance specifications. The technical advancements involved include mirror technologies, control system features, the telescope suspension system, and the aircraft open port cavity with associated cavity door that opens in flight and tracks the telescope elevation angle. For background this paper will provide a brief programmatic overview of the SOFIA project including the joint project arrangement between the US and Germany (NASA and DLR). Additionally, this paper will describe the up to date status of the development of SOFIA as the Observatory nears the date of the first test flight in the summer of 2004.

L-Band System Engineering - Concepts of Use, Systems Performance Requirements, and Architecture

NASA Technical Reports Server (NTRS)

Henriksen, Stephen; Zelkin, Natalie

2011-01-01

This document is being provided as part of ITT s NASA Glenn Research Center Aerospace Communication Systems Technical Support (ACSTS) contract NNC05CA85C, Task 7: New ATM Requirements-Future Communications, C-band and L-band Communications Standard Development. Task 7 was motivated by the five year technology assessment performed for the Federal Aviation Administration (FAA) under the joint FAA-EUROCONTROL cooperative research Action Plan (AP-17), also known as the Future Communications Study (FCS). It was based on direction provided by the FAA project-level agreement (PLA FY09_G1M.02-02v1) for "New ATM Requirements-Future Communications." Task 7 was separated into two distinct subtasks, each aligned with specific work elements and deliverable items. Subtask 7-1 addressed C-band airport surface data communications standards development, systems engineering, test bed development, and tests/demonstrations to establish operational capability for what is now referred to as the Aeronautical Mobile Airport Communications System (AeroMACS). Subtask 7-2, which is the subject of this report, focused on preliminary systems engineering and support of joint FAA/EUROCONTROL development and evaluation of a future L-band (960 to 1164 MHz) air/ground (A/G) communication system known as the L-band digital aeronautical communications system (L-DACS), which was defined during the FCS. The proposed L-DACS will be capable of providing ATM services in continental airspace in the 2020+ timeframe. Subtask 7-2 was performed in two phases. Phase I featured development of Concepts of Use, high level functional analyses, performance of initial L-band system safety and security risk assessments, and development of high level requirements and architectures. It also included the aforementioned support of joint L-DACS development and evaluation, including inputs to L-DACS design specifications. Phase II provided a refinement of the systems engineering activities performed during Phase I, along

Application of objective clinical human reliability analysis (OCHRA) in assessment of technical performance in laparoscopic rectal cancer surgery.

PubMed

Foster, J D; Miskovic, D; Allison, A S; Conti, J A; Ockrim, J; Cooper, E J; Hanna, G B; Francis, N K

2016-06-01

Laparoscopic rectal resection is technically challenging, with outcomes dependent upon technical performance. No robust objective assessment tool exists for laparoscopic rectal resection surgery. This study aimed to investigate the application of the objective clinical human reliability analysis (OCHRA) technique for assessing technical performance of laparoscopic rectal surgery and explore the validity and reliability of this technique. Laparoscopic rectal cancer resection operations were described in the format of a hierarchical task analysis. Potential technical errors were defined. The OCHRA technique was used to identify technical errors enacted in videos of twenty consecutive laparoscopic rectal cancer resection operations from a single site. The procedural task, spatial location, and circumstances of all identified errors were logged. Clinical validity was assessed through correlation with clinical outcomes; reliability was assessed by test-retest. A total of 335 execution errors identified, with a median 15 per operation. More errors were observed during pelvic tasks compared with abdominal tasks (p < 0.001). Within the pelvis, more errors were observed during dissection on the right side than the left (p = 0.03). Test-retest confirmed reliability (r = 0.97, p < 0.001). A significant correlation was observed between error frequency and mesorectal specimen quality (r s = 0.52, p = 0.02) and with blood loss (r s = 0.609, p = 0.004). OCHRA offers a valid and reliable method for evaluating technical performance of laparoscopic rectal surgery.

Analysis of Running and Technical Performance in Substitute Players in International Male Rugby Union Competition.

PubMed

Lacome, Mathieu; Piscione, Julien; Hager, Jean-Philippe; Carling, Christopher

2016-09-01

To investigate the patterns and performance of substitutions in 18 international 15-a-side men's rugby union matches. A semiautomatic computerized time-motion system compiled 750 performance observations for 375 players (422 forwards, 328 backs). Running and technical-performance measures included total distance run, high-intensity running (>18.0 km/h), number of individual ball possessions and passes, percentage of passes completed, and number of attempted and percentage of successful tackles. A total of 184 substitutions (85.2%) were attributed to tactical and 32 (14.8%) to injury purposes respectively. The mean period for non-injury-purpose substitutions in backs (17.7%) occurred between 70 and 75 min, while forward substitutions peaked equally between 50-55 and 60-65 min (16.4%). Substitutes generally demonstrated improved running performance compared with both starter players who completed games and players whom they replaced (small differences, ES -0.2 to 0.5) in both forwards and backs over their entire time played. There was also a trend for better running performance in forward and back substitutes over their first 10 min of play compared with the final 10 min for replaced players (small to moderate differences, ES 0.3-0.6). Finally, running performance in both forward and back substitutes was generally lower (ES -0.1 to 0.3, unclear or small differences) over their entire 2nd-half time played compared with their first 10 min of play. The impact of substitutes on technical performance was generally considered unclear. This information provides practitioners with practical data relating to the physical and technical contributions of substitutions that subsequently could enable optimization of their impact on match play.

Investigating Aerobic, Anaerobic Combine Technical Trainings' Effects on Performance in Tennis Players

ERIC Educational Resources Information Center

Suna, Gürhan; Kumartasli, Mehmet

2017-01-01

The aim of this study is to investigate eight-week aerobic, anaerobic combine technical trainings' effects on developments of performance. 21 athletes of tennis proficiency students from Sports Sciences Department were joined to the study voluntarily. Participated in the research athletes' ages' mean was 22,2 ± 0,3 year, lengths' mean was 177,3 ±…

Evolution and revolution: gauging the impact of technological and technical innovation on Olympic performance.

PubMed

Balmer, Nigel; Pleasence, Pascoe; Nevill, Alan

2012-01-01

A number of studies have pointed to a plateauing of athletic performance, with the suggestion that further improvements will need to be driven by revolutions in technology or technique. In the present study, we examine post-war men's Olympic performance in jumping events (pole vault, long jump, high jump, triple jump) to determine whether performance has indeed plateaued and to present techniques, derived from models of human growth, for assessing the impact of technological and technical innovation over time (logistic and double logistic models of growth). Significantly, two of the events involve well-documented changes in technology (pole material in pole vault) or technique (the Fosbury Flop in high jump), while the other two do not. We find that in all four cases, performance appears to have plateaued and that no further "general" improvement should be expected. In the case of high jump, the double logistic model provides a convenient method for modelling and quantifying a performance intervention (in this case the Fosbury Flop). However, some shortcomings are revealed for pole vault, where evolutionary post-war improvements and innovation (fibre glass poles) were concurrent, preventing their separate identification in the model. In all four events, it is argued that further general growth in performance will indeed need to rely predominantly on technological or technical innovation.

The Technical Work Plan Tracking Tool

NASA Technical Reports Server (NTRS)

Chullen, Cinda; Leighton, Adele; Weller, Richard A.; Woodfill, Jared; Parkman, William E.; Ellis, Glenn L.; Wilson, Marilyn M.

2003-01-01

The Technical Work Plan Tracking Tool is a web-based application that enables interactive communication and approval of contract requirements that pertain to the administration of the Science, Engineering, Analysis, and Test (SEAT) contract at Johnson Space Center. The implementation of the application has (1) shortened the Technical Work Plan approval process, (2) facilitated writing and documenting requirements in a performance-based environment with associated surveillance plans, (3) simplified the contractor s estimate of the cost for the required work, and (4) allowed for the contractor to document how they plan to accomplish the work. The application is accessible to over 300 designated NASA and contractor employees via two Web sites. For each employee, the application regulates access according to the employee s authority to enter, view, and/or print out diverse information, including reports, work plans, purchase orders, and financial data. Advanced features of this application include on-line approval capability, automatic e-mail notifications requesting review by subsequent approvers, and security inside and outside the firewall.

Advanced Transportation System Studies Technical Area 2 (TA-2) Heavy Lift Launch Vehicle Development Contract. Volume 2; Technical Results

NASA Technical Reports Server (NTRS)

1995-01-01

The purpose of the Advanced Transportation System Studies (ATSS) Technical Area 2 (TA-2) Heavy Lift Launch Vehicle Development contract was to provide advanced launch vehicle concept definition and analysis to assist NASA in the identification of future launch vehicle requirements. Contracted analysis activities included vehicle sizing and performance analysis, subsystem concept definition, propulsion subsystem definition (foreign and domestic), ground operations and facilities analysis, and life cycle cost estimation. This document is Volume 2 of the final report for the contract. It provides documentation of selected technical results from various TA-2 analysis activities, including a detailed narrative description of the SSTO concept assessment results, a user's guide for the associated SSTO sizing tools, an SSTO turnaround assessment report, an executive summary of the ground operations assessments performed during the first year of the contract, a configuration-independent vehicle health management system requirements report, a copy of all major TA-2 contract presentations, a copy of the FLO launch vehicle final report, and references to Pratt & Whitney's TA-2 sponsored final reports regarding the identification of Russian main propulsion technologies.

C2 Link Security for UAS: Technical Literature Study and Preliminary Functional Requirements. Version 0.9 (Working Draft)

NASA Technical Reports Server (NTRS)

2005-01-01

This document provides a study of the technical literature related to Command and Control (C2) link security for Unmanned Aircraft Systems (UAS) for operation in the National Airspace System (NAS). Included is a preliminary set of functional requirements for C2 link security.

Fuel cells for transport: can the promise be fulfilled? Technical requirements and demands from customers

NASA Astrophysics Data System (ADS)

Klaiber, Thomas

The paper discusses the technical requirements and the customer demands for vehicles that have an on-board methanol reformer and fuel cells. The research concentrates on the technical developmental risks which include minimizing volume, reducing weight and, at the same time, improving efficiency and system dynamics. Fuel cell powered vehicles with methanol reformers are not only suitable for a niche market but also these vehicles will compete with conventional vehicles. The greatest hindrance will be the price of the fuel cell. A possible progressive development of the number of fuel cell powered vehicles in conjunction with a reduction in costs will be discussed in the paper. When fuel cell vehicles come to the market it is necessary that an infrastructure for the fuel methanol or hydrogen is installed. Therefore, it will only be possible to introduce fuel cell vehicles into special markets, e.g. California. Such a process will need to be subsidized by additional incentives like tax concessions. Today there are many technical risks and unsolved problems relating to production technologies, infrastructure, and costs. Nevertheless, among the alternative power units, the fuel cell seems to be the only one that might be competitive to the conventional power unit, especially relating to emissions.

75 FR 76254 - Official Performance and Procedural Requirements for Grain Weighing Equipment and Related Grain...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-08

... requirements of the 2008 edition of the National Institute of Standards and Technology (NIST) Handbook 44, ``Specifications, Tolerances, and Other Technical Requirements for Weighing and Measuring Devices,'' (NIST Handbook... identified as ``NIST Handbook 44 IBF Comments,'' making reference to the date and page number of this issue...

40 CFR 63.7 - Performance testing requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Performance testing requirements. (a) Applicability and performance test dates. (1) The applicability of this... or operator of the affected source must perform such tests within 180 days of the compliance date for... standard initially, the owner or operator shall conduct a second performance test within 3 years and 180...

Technical proficiency in hand-assisted laparoscopic colon and rectal surgery: determining how many cases are required to achieve mastery.

PubMed

Pendlimari, Rajesh; Holubar, Stefan D; Dozois, Eric J; Larson, David W; Pemberton, John H; Cima, Robert R

2012-04-01

To determine how many cases are required to achieve technical proficiency for hand-assisted laparoscopic surgery (HALS). Retrospective study. Tertiary care hospital. Using a prospective database, all HALS colorectal resections from 2003 to 2009 by 2 surgeons (A and B) were reviewed. Over 6 years, surgeons A and B performed 397 and 322 cases. Change-Point Analysis (CUSUM) was used to define the number of cases required to effect improvement in operative time. Cases before and after the change point were considered as being in the "learning period" and "skilled period." Operative time; short-term outcomes. The change point occurred after 108 and 105 cases for surgeons A and B, respectively. The learning period and skilled period were similar with respect to age, sex, body mass index, prior abdominal surgery, medical comorbidities, and American Society of Anesthesiologists class. Mean overall operative time decreased from 263 to 185 minutes (P < .001). The decrease in mean operative duration for specific resections were as follows: right colectomy, 35 minutes (P = .003); left colectomy, 63 minutes (P = .006); sigmoid colectomy, 63 minutes (P < .001); anterior resection, 70 minutes (P < .001); coloanal anastomosis, 52 minutes (P = .003); subtotal colectomy, 75 minutes (P < .001); and total proctocolectomy with ileal reservoir, 80 minutes (P < .001). Intraoperative complications and conversion rate were similar, but overall morbidity, infectious complications, readmissions, and length of stay were all significantly (P < .05) lower during the skilled period. For HALS colorectal resection, technical proficiency occurred after approximately 105 cases, and increased surgeon experience resulted in improved short-term outcomes. These data suggest that the learning curve for HALS colorectal resection will extend beyond fellowship training for many colorectal surgeons.

14 CFR 171.269 - Marker beacon performance requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Marker beacon performance requirements. 171.269 Section 171.269 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... Landing System (ISMLS) § 171.269 Marker beacon performance requirements. ISMLS marker beacon equipment...

Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ulm, Franz-Josef

2000-03-31

OAK-B135 Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 3(NOTE: Part II A item 1 indicates ''PAPER'', but a report is attached electronically)

Technical activity profile and influence of body anthropometry on playing performance in female elite team handball.

PubMed

Michalsik, Lars B; Aagaard, Per; Madsen, Klavs

2015-04-01

To determine the physical demands placed on female elite team handball (TH) players in relation to playing position and body anthropometry, female elite TH primarily field players were monitored during match-play using video recording and subsequent computerized technical match analysis during 5 regular tournament match seasons. Technical match activities were distributed in 6 major types of playing actions (shots, breakthroughs, fast breaks, technical errors, defensive errors, and tackles) and further divided into various subcategories (e.g., type of shot, hard or light tackles, claspings, screenings, and blockings). Furthermore, anthropometric measurements were performed. Each player had 28.3 ± 11.0 (group means ± SD) high-intense playing actions per match with a total effective playing time of 50.70 ± 5.83 minutes. On average, each player made 2.8 ± 2.6 fast breaks, gave 7.9 ± 14.4 screenings, received 14.6 ± 9.2 tackles in total, and performed 7.7 ± 3.7 shots while in offense, along with 3.5 ± 3.8 blockings, 1.9 ± 2.7 claspings, and 6.2 ± 3.8 hard tackles in defense. Mean body height, body mass, and age in the Danish Premier Female Team Handball League were 175.4 ± 6.1 cm, 69.5 ± 6.5 kg, and 25.4 ± 3.7 years, respectively. Wing players were lighter (63.5 ± 4.8 kg, p < 0.001) and smaller (169.3 ± 4.9 cm, p < 0.001) than backcourt players (BP) (70.6 ± 5.3 kg, 177.0 ± 5.4 cm) and pivots (PV) (72.5 ± 4.9 kg, 177.7 ± 4.9 cm). In conclusion, the present match observations revealed that female elite TH players during competitive games intermittently perform a high number of short-term, high-intense technical playing actions making modern female elite TH a physically demanding team sport. No sign of technical fatigue were observed, since the amount of intense technical playing actions remained unchanged in the second half. Marked positional differences in the physical demands were demonstrated, with wing players performing more fast breaks and less

Academic Performance of Students during Transition Period before Choice of Disciplines in Nigeria Certificate in Education (Technical) Programme

ERIC Educational Resources Information Center

Amasuomo, Japo Oweikeye

2015-01-01

The study examined the academic performance of students in the compulsory courses in technical education during the transition period of first and second years of three years Nigeria Certificate in Education (NCE) Technical programme before choosing their disciplines in the third year. The study comprised of 237 students that consisted of…

Positional interchanges influence the physical and technical match performance variables of elite soccer players.

PubMed

Schuth, G; Carr, G; Barnes, C; Carling, C; Bradley, P S

2016-01-01

Positional variation in match performance is well established in elite soccer but no information exists on players switching positions. This study investigated the influence of elite players interchanging from one position to another on physical and technical match performance. Data were collected from multiple English Premier League (EPL) seasons using a computerised tracking system. After adhering to stringent inclusion criteria, players were examined across several interchanges: central-defender to fullback (CD-FB, n = 11, 312 observations), central-midfielder to wide-midfielder (CM-WM, n = 7, 171 observations), wide-midfielder to central-midfielder (WM-CM, n = 7, 197 observations) and attacker to wide-midfielder (AT-WM, n = 4, 81 observations). Players interchanging from CD-FB covered markedly more high-intensity running and sprinting distance (effect size [ES]: -1.56 and -1.26), lost more possessions but made more final third entries (ES: -1.23 and -1.55). Interchanging from CM-WM and WM-CM resulted in trivial to moderate differences in both physical (ES: -0.14-0.59 and -0.21-0.39) and technical performances (ES: -0.48-0.64 and -0.36-0.54). Players interchanging from AT-WM demonstrated a moderate difference in high-intensity running without possession (ES: -0.98) and moderate-to-large differences in the number of clearances, tackles and possessions won (ES: -0.77, -1.16 and -1.41). The data demonstrate that the physical and technical demands vary greatly from one interchange to another but utility players seem able to adapt to these positional switches.

Radiographic technical quality of root canal treatment performed by a new rotary single-file system.

PubMed

Colombo, Marco; Bassi, Cristina; Beltrami, Riccardo; Vigorelli, Paolo; Spinelli, Antonio; Cavada, Andrea; Dagna, Alberto; Chiesa, Marco; Poggio, Claudio

2017-01-01

The aim of the present study was to evaluate radiographically the technical quality of root canal filling performed by postgraduate students with a new single-file Nickel-Titanium System (F6 Skytaper Komet) in clinical practice. Records of 74 patients who had received endodontic treatment by postgraduate students at the School of Dentistry, Faculty of Medicine, University of Pavia in the period between September 2015 and April 2016 were collected and examined: the final sample consisted 114 teeth and 204 root canals. The quality of endodontic treatment was evaluated by examining the length of the filling in relation to the radiographic apex, the density of the obturation according to the presence of voids and the taper of root canal filling. Chi-squared analysis was used to determine statistically significant differences between the technical quality of root fillings according to tooth's type, position and curvature. The results showed that 75,49%, 82,84% and 90,69% of root filled canals had adequate length, density and taper respectively. Overall, the technical quality of root canal fillings performed by postgraduates students was acceptable in 60,78% of the cases.

Higher speed freight truck design : performance requirements.

DOT National Transportation Integrated Search

2013-10-01

This proposed requirements document combines a set of requirements for high-speed freight car truck design and performance : from the generally accepted standards in the U.S. Code of Federal Regulation (CFR), the Association of American Railroads : (...

Nighttime kidney transplantation is associated with less pure technical graft failure.

PubMed

Brunschot, Denise M D Özdemir-van; Hoitsma, Andries J; van der Jagt, Michel F P; d'Ancona, Frank C; Donders, Rogier A R T; van Laarhoven, Cees J H M; Hilbrands, Luuk B; Warlé, Michiel C

2016-07-01

To minimize cold ischemia time, transplantations with kidneys from deceased donors are frequently performed during the night. However, sleep deprivation of those who perform the transplantation may have adverse effects on cognitive and psychomotor performance and may cause reduced cognitive flexibility. We hypothesize that renal transplantations performed during the night are associated with an increased incidence of pure technical graft failure. A retrospective analysis of data of the Dutch Organ Transplant Registry concerning all transplants from deceased donors between 2000 and 2013 was performed. Nighttime surgery was defined as the start of the procedure between 8 p.m. and 8 a.m. The primary outcome measure was technical graft failure, defined as graft loss within 10 days after surgery without signs of (hyper)acute rejection. Of 4.519 renal transplantations in adult recipients, 1.480 were performed during the night. The incidence of pure technical graft failure was 1.0 % for procedures started during the night versus 2.6 % for daytime surgery (p = .001). In a multivariable model, correcting for relevant donor, recipient and graft factors, daytime surgery was an independent predictor of pure technical graft failure (p < .001). Limitation of this study is mainly to its retrospective design, and the influence of some relevant variables, such as the experience level of the surgeon, could not be assessed. We conclude that nighttime surgery is associated with less pure technical graft failures. Further research is required to explore factors that may positively influence the performance of the surgical team during the night.

4D Dynamic Required Navigation Performance Final Report

NASA Technical Reports Server (NTRS)

Finkelsztein, Daniel M.; Sturdy, James L.; Alaverdi, Omeed; Hochwarth, Joachim K.

2011-01-01

New advanced four dimensional trajectory (4DT) procedures under consideration for the Next Generation Air Transportation System (NextGen) require an aircraft to precisely navigate relative to a moving reference such as another aircraft. Examples are Self-Separation for enroute operations and Interval Management for in-trail and merging operations. The current construct of Required Navigation Performance (RNP), defined for fixed-reference-frame navigation, is not sufficiently specified to be applicable to defining performance levels of such air-to-air procedures. An extension of RNP to air-to-air navigation would enable these advanced procedures to be implemented with a specified level of performance. The objective of this research effort was to propose new 4D Dynamic RNP constructs that account for the dynamic spatial and temporal nature of Interval Management and Self-Separation, develop mathematical models of the Dynamic RNP constructs, "Required Self-Separation Performance" and "Required Interval Management Performance," and to analyze the performance characteristics of these air-to-air procedures using the newly developed models. This final report summarizes the activities led by Raytheon, in collaboration with GE Aviation and SAIC, and presents the results from this research effort to expand the RNP concept to a dynamic 4D frame of reference.

Civilian Radioactive Waste Management System Requirements Document

DOE Office of Scientific and Technical Information (OSTI.GOV)

C.A. Kouts

2006-05-10

The CRD addresses the requirements of Department of Energy (DOE) Order 413.3-Change 1, ''Program and Project Management for the Acquisition of Capital Assets'', by providing the Secretarial Acquisition Executive (Level 0) scope baseline and the Program-level (Level 1) technical baseline. The Secretarial Acquisition Executive approves the Office of Civilian Radioactive Waste Management's (OCRWM) critical decisions and changes against the Level 0 baseline; and in turn, the OCRWM Director approves all changes against the Level 1 baseline. This baseline establishes the top-level technical scope of the CRMWS and its three system elements, as described in section 1.3.2. The organizations responsible formore » design, development, and operation of system elements described in this document must therefore prepare subordinate project-level documents that are consistent with the CRD. Changes to requirements will be managed in accordance with established change and configuration control procedures. The CRD establishes requirements for the design, development, and operation of the CRWMS. It specifically addresses the top-level governing laws and regulations (e.g., ''Nuclear Waste Policy Act'' (NWPA), 10 Code of Federal Regulations (CFR) Part 63, 10 CFR Part 71, etc.) along with specific policy, performance requirements, interface requirements, and system architecture. The CRD shall be used as a vehicle to incorporate specific changes in technical scope or performance requirements that may have significant program implications. Such may include changes to the program mission, changes to operational capability, and high visibility stakeholder issues. The CRD uses a systems approach to: (1) identify key functions that the CRWMS must perform, (2) allocate top-level requirements derived from statutory, regulatory, and programmatic sources, and (3) define the basic elements of the system architecture and operational concept. Project-level documents address CRD requirements by

43 CFR 5451.1 - Minimum performance bond requirements; types.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 43 Public Lands: Interior 2 2011-10-01 2011-10-01 false Minimum performance bond requirements... § 5451.1 Minimum performance bond requirements; types. (a) A minimum performance bond of not less than 20... minimum bond as provided in § 5451.2 of this title. A minimum performance bond of not less than $500 will...

Effects of age, tenure, training, and job complexity on technical performance.

PubMed

Sparrow, P R; Davies, D R

1988-09-01

Effects on performance of age, tenure, training level, and job complexity were investigated in a cross-sectional study using a sample of 1,308 service engineers employed by a multinational office equipment company. Two measures of job performance were derived from production record data, one relating to the quality of servicing and the other to the speed with which services were completed. Scores for each performance measure were analyzed by analysis of variance. For the quality of servicing measure, a significant main effect of age and a significant Age X Training interaction were obtained, and the relation between age and job performance took the form of an inverted U. For the speed of servicing measure, the main effects of age, tenure, training level, and job complexity were significant and there were no significant interactions. However, for both performance measures, age accounted for only a very small proportion of the variance. We discuss these results with reference to the existing literature on age and technical job performance, and conclude that training, especially if it is recent, may moderate adverse effects of age on job performance.

Analysis Influence of Managerial Competence, Technical Competence, and Strategic Competence on Firm Performance in Electrical Engineering Company in Bandung

NASA Astrophysics Data System (ADS)

Wijaya, E. R.; Irianto, D.

2018-03-01

The industry sectors that have an important role in the era of globalization is the electro engineering sector. The era of globalization led to intense competition. One of the negative effects of the intense competition is declining profits. Drop in profits caused many firms reduces their employees without seeking the root cause of declining profits in detail. Whereas, employee is the important resources to maintain competitive advantage. Competitive advantage can be measured by the performance of which is owned by the firm. The firm's performance can be formed of competencies that is unique, rare, irreplaceable, and difficult to imitate within the firm, one of them is the competence of the individual. According to a competency-based approach and the resource- based approach, individual competence that affect the performance of the firm is managerial competence, technical competence, and strategic competence. Questionnaire is built based on the dimensions of the firm's performance, managerial competence, technical competence, and strategic competence, are processed using partial least squares application. The results indicate that managerial competence negatively impact firm’s performance with weak ties. The technical competence and strategic competence positively affect firm’s performance with moderate ties.

47 CFR 18.207 - Technical report.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 1 2013-10-01 2013-10-01 false Technical report. 18.207 Section 18.207... Applications and Authorizations § 18.207 Technical report. When required by the Commission a technical report...(s) under which the equipment is or will be marketed. (e) A statement of the rated technical...

47 CFR 18.207 - Technical report.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 1 2014-10-01 2014-10-01 false Technical report. 18.207 Section 18.207... Applications and Authorizations § 18.207 Technical report. When required by the Commission a technical report...(s) under which the equipment is or will be marketed. (e) A statement of the rated technical...

47 CFR 18.207 - Technical report.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 1 2012-10-01 2012-10-01 false Technical report. 18.207 Section 18.207... Applications and Authorizations § 18.207 Technical report. When required by the Commission a technical report...(s) under which the equipment is or will be marketed. (e) A statement of the rated technical...

48 CFR 2052.211-70 - Preparation of technical reports.

Code of Federal Regulations, 2014 CFR

2014-10-01

....211-70 Preparation of technical reports. As prescribed at 2011.104-70(a), the contracting officer... Reports (JAN 1993) All technical reports required by Section C and all Technical Progress Reports required... 48 Federal Acquisition Regulations System 6 2014-10-01 2014-10-01 false Preparation of technical...

48 CFR 2052.211-70 - Preparation of technical reports.

Code of Federal Regulations, 2012 CFR

2012-10-01

....211-70 Preparation of technical reports. As prescribed at 2011.104-70(a), the contracting officer... Reports (JAN 1993) All technical reports required by Section C and all Technical Progress Reports required... 48 Federal Acquisition Regulations System 6 2012-10-01 2012-10-01 false Preparation of technical...

48 CFR 2052.211-70 - Preparation of technical reports.

Code of Federal Regulations, 2010 CFR

2010-10-01

....211-70 Preparation of technical reports. As prescribed at 2011.104-70(a), the contracting officer... Reports (JAN 1993) All technical reports required by Section C and all Technical Progress Reports required... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Preparation of technical...

48 CFR 2052.211-70 - Preparation of technical reports.

Code of Federal Regulations, 2013 CFR

2013-10-01

....211-70 Preparation of technical reports. As prescribed at 2011.104-70(a), the contracting officer... Reports (JAN 1993) All technical reports required by Section C and all Technical Progress Reports required... 48 Federal Acquisition Regulations System 6 2013-10-01 2013-10-01 false Preparation of technical...

48 CFR 2052.211-70 - Preparation of technical reports.

Code of Federal Regulations, 2011 CFR

2011-10-01

....211-70 Preparation of technical reports. As prescribed at 2011.104-70(a), the contracting officer... Reports (JAN 1993) All technical reports required by Section C and all Technical Progress Reports required... 48 Federal Acquisition Regulations System 6 2011-10-01 2011-10-01 false Preparation of technical...

Assessing Students' Technical Skill Attainment

ERIC Educational Resources Information Center

Jorgensen, Haley

2010-01-01

The Wisconsin Technical College System (WTCS) is working to comply with the Carl D. Perkins Career and Technical Education Improvement Act of 2006 (Perkins) to ensure that its graduates have mastered the technical skills needed by business and industry. The legislation requires that each state identify and approve program assessment strategies…

Mental Health and Academic Performance among Associate Degree Nursing Students at a Technical College

ERIC Educational Resources Information Center

Kliminski, Kerri

2017-01-01

The purpose of this non-experimental cross-sectional quantitative study was to examine the relationship between mental health and academic performance among associate degree nursing (ADN) students at a Midwest technical college by identifying incidence of positive mental health, mental illness symptoms/distress, and mental illness; the…

40 CFR 158.400 - Product performance data requirements table.

Code of Federal Regulations, 2011 CFR

2011-07-01

... to human health and whose presence cannot readily be observed by the user including, but not limited...) PESTICIDE PROGRAMS DATA REQUIREMENTS FOR PESTICIDES Product Performance § 158.400 Product performance data... the product performance data requirements for a particular pesticide product. Notes that apply to an...

40 CFR 158.400 - Product performance data requirements table.

Code of Federal Regulations, 2012 CFR

2012-07-01

... to human health and whose presence cannot readily be observed by the user including, but not limited...) PESTICIDE PROGRAMS DATA REQUIREMENTS FOR PESTICIDES Product Performance § 158.400 Product performance data... the product performance data requirements for a particular pesticide product. Notes that apply to an...

40 CFR 158.400 - Product performance data requirements table.

Code of Federal Regulations, 2014 CFR

2014-07-01

... product bears a claim to control pest microorganisms that pose a threat to human health and whose presence...) PESTICIDE PROGRAMS DATA REQUIREMENTS FOR PESTICIDES Product Performance § 158.400 Product performance data... the product performance data requirements for a particular pesticide product. Notes that apply to an...

40 CFR 158.400 - Product performance data requirements table.

Code of Federal Regulations, 2010 CFR

2010-07-01

... to human health and whose presence cannot readily be observed by the user including, but not limited...) PESTICIDE PROGRAMS DATA REQUIREMENTS FOR PESTICIDES Product Performance § 158.400 Product performance data... the product performance data requirements for a particular pesticide product. Notes that apply to an...

40 CFR 158.400 - Product performance data requirements table.

Code of Federal Regulations, 2013 CFR

2013-07-01

... product bears a claim to control pest microorganisms that pose a threat to human health and whose presence...) PESTICIDE PROGRAMS DATA REQUIREMENTS FOR PESTICIDES Product Performance § 158.400 Product performance data... the product performance data requirements for a particular pesticide product. Notes that apply to an...

42 CFR 84.103 - Man tests; performance requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Man tests; performance requirements. 84.103 Section...-Contained Breathing Apparatus § 84.103 Man tests; performance requirements. (a) The apparatus shall satisfy... is 24 ±6 °C. (75 ±10 °F.), the maximum temperature of inspired air recorded during man tests shall...

42 CFR 84.103 - Man tests; performance requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Man tests; performance requirements. 84.103 Section...-Contained Breathing Apparatus § 84.103 Man tests; performance requirements. (a) The apparatus shall satisfy... is 24 ±6 °C. (75 ±10 °F.), the maximum temperature of inspired air recorded during man tests shall...

42 CFR 84.103 - Man tests; performance requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Man tests; performance requirements. 84.103 Section...-Contained Breathing Apparatus § 84.103 Man tests; performance requirements. (a) The apparatus shall satisfy... is 24 ±6 °C. (75 ±10 °F.), the maximum temperature of inspired air recorded during man tests shall...

Engineered Barrier System performance requirements systems study report. Revision 02

DOE Office of Scientific and Technical Information (OSTI.GOV)

Balady, M.A.

This study evaluates the current design concept for the Engineered Barrier System (EBS), in concert with the current understanding of the geologic setting to assess whether enhancements to the required performance of the EBS are necessary. The performance assessment calculations are performed by coupling the EBS with the geologic setting based on the models (some of which were updated for this study) and assumptions used for the 1995 Total System Performance Assessment (TSPA). The need for enhancements is determined by comparing the performance assessment results against the EBS related performance requirements. Subsystem quantitative performance requirements related to the EBS includemore » the requirement to allow no more than 1% of the waste packages (WPs) to fail before 1,000 years after permanent closure of the repository, as well as a requirement to control the release rate of radionuclides from the EBS. The EBS performance enhancements considered included additional engineered components as well as evaluating additional performance available from existing design features but for which no performance credit is currently being taken.« less

The 30/20 GHz communications system functional requirements

NASA Technical Reports Server (NTRS)

Siperko, C. M.; Frankfort, M.; Markham, R.; Wall, M.

1981-01-01

The characteristics of 30/20 GHz usage in satellite systems to be used in support of projected communication requirements of the 1990's are defined. A requirements analysis which develops projected market demand for satellite services by general and specialized carriers and an analysis of the impact of propagation and system constraints on 30/20 GHz operation are included. A set of technical performance characteristics for the 30/20 GHz systems which can serve the resulting market demand and the experimental program necessary to verify technical and operational aspects of the proposed systems is also discussed.

Key team physical and technical performance indicators indicative of team quality in the soccer Chinese super league.

PubMed

Yang, Gai; Leicht, Anthony S; Lago, Carlos; Gómez, Miguel-Ángel

2018-01-01

The aim of this study was to identify the key physical and technical performance variables related to team quality in the Chinese Super League (CSL). Teams' performance variables were collected from 240 matches and analysed via analysis of variance between end-of-season-ranked groups and multinomial logistic regression. Significant physical performance differences between groups were identified for sprinting (top-ranked group vs. upper-middle-ranked group) and total distance covered without possession (upper and upper-middle-ranked groups and lower-ranked group). For technical performance, teams in the top-ranked group exhibited a significantly greater amount of possession in opponent's half, number of entry passes in the final 1/3 of the field and the Penalty Area, and 50-50 challenges than lower-ranked teams. Finally, time of possession increased the probability of a win compared with a draw. The current study identified key performance indicators that differentiated end-season team quality within the CSL.

The French Space Operation Act: Technical Regulations

NASA Astrophysics Data System (ADS)

Trinchero, J. P.; Lazare, B.

2010-09-01

The French Space Operation Act(FSOA) stipulates that a prime objective of the National technical regulations is to protect people, property, public health and the environment. Compliance with these technical regulations is mandatory as of 10 December 2010 for space operations by French space operators and for space operations from French territory. The space safety requirements and regulations governing procedures are based on national and international best practices and experience. A critical design review of the space system and procedures shall be carried out by the applicant, in order to verify compliance with the Technical Regulations. An independent technical assessment of the operation is delegated to CNES. The principles applied when drafting technical regulations are as follows: requirements must as far as possible establish the rules according to the objective to be obtained, rather than how it is to be achieved; requirements must give preference to international standards recognised as being the state of the art; requirements must take previous experience into account. Technical regulations are divided into three sections covering common requirements for the launch, control and return of a space object. A dedicated section will cover specific rules to be applied at the Guiana Space Centre. The main topics addressed by the technical regulations are: operator safety management system; study of risks to people, property, public health and the Earth’s environment; impact study on the outer space environment: space debris generated by the operation; planetary protection.

International Low Impact Docking System (iLIDS) Project Technical Requirements Specification, Revision F

NASA Technical Reports Server (NTRS)

Lewis, James L.

2011-01-01

The NASA Docking System (NDS) is NASA's implementation for the emerging International Docking System Standard (IDSS) using low impact docking technology. The NASA Docking System Project (NDSP) is the International Space Station (ISS) Program's project to produce the NDS, Common Docking Adapter (CDA) and Docking Hub. The NDS design evolved from the Low Impact Docking System (LIDS). The acronym international Low Impact Docking System (iLIDS) is also used to describe this system as well as the Government Furnished Equipment (GFE) project designing the NDS for the NDSP. NDS and iLIDS may be used interchangeability. This document will use the acronym iLIDS. Some of the heritage documentation and implementations (e.g., software command names, requirement identification (ID), figures, etc.) used on NDS will continue to use the LIDS acronym. This specification defines the technical requirements for the iLIDS GFE delivered to the NDSP by the iLIDS project. This document contains requirements for two iLIDS configurations, SEZ29101800-301 and SEZ29101800-302. Requirements with the statement, iLIDS shall, are for all configurations. Examples of requirements that are unique to a single configuration may be identified as iLIDS (-301) shall or iLIDS (-302) shall. Furthermore, to allow a requirement to encompass all configurations with an exception, the requirement may be designated as iLIDS (excluding -302) shall. Verification requirements for the iLIDS project are identified in the Verification Matrix (VM) provided in the iLIDS Verification and Validation Document, JSC-63966. The following definitions differentiate between requirements and other statements: Shall: This is the only verb used for the binding requirements. Should/May: These verbs are used for stating non-mandatory goals. Will: This verb is used for stating facts or declaration of purpose. A Definition of Terms table is provided in Appendix B to define those terms with specific tailored uses in this document.

29 CFR 1620.17 - Jobs requiring equal responsibility in performance.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 29 Labor 4 2013-07-01 2013-07-01 false Jobs requiring equal responsibility in performance. 1620.17... THE EQUAL PAY ACT § 1620.17 Jobs requiring equal responsibility in performance. (a) In general. The equal pay standard applies to jobs the performance of which requires equal responsibility...

29 CFR 1620.17 - Jobs requiring equal responsibility in performance.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 4 2014-07-01 2014-07-01 false Jobs requiring equal responsibility in performance. 1620.17... THE EQUAL PAY ACT § 1620.17 Jobs requiring equal responsibility in performance. (a) In general. The equal pay standard applies to jobs the performance of which requires equal responsibility...

Individualized deliberate practice on a virtual reality simulator improves technical performance of surgical novices in the operating room: a randomized controlled trial.

PubMed

Palter, Vanessa N; Grantcharov, Teodor P

2014-03-01

The purpose of this study was to investigate whether individualized deliberate practice on a virtual reality (VR) simulator results in improved technical performance in the operating room. Training on VR simulators has been shown to improve technical performance in the operating room (OR). Currently described VR curricula consist of trainees practicing the same tasks until expert proficiency is reached. It has yet to be investigated whether the individualized deliberate practice, where curricula tasks vary depending on prior levels of technical proficiency, would translate into the OR. This single-blinded prospective trial randomized 16 novice surgical residents to a deliberate practice (DP) group and a conventional residency training group. Both groups performed a laparoscopic cholecystectomy in the OR that was video-recorded. Technical performance of DP group residents in the OR was assessed using 3 validated assessment tools. A score of less than 60% on any component of the assessment tool resulted in the trainee practicing a specific task on the VR simulator. The DP group practiced on the simulator as per their individualized schedule. Both groups then performed another laparoscopic cholecystectomy. A blinded expert assessed the OR recordings using a validated global rating scale. Although both groups had similar technical abilities preintervention [DP: median score, 13.5 (9.3-15.0); control: median score, 14.5 (9.3-17.8); P = 0.45], the DP residents had a superior technical performance postintervention [DP: median score, 17.0 (15.3-18.5); control: median score, 12.5 (7.5-14.0); P = 0.03]. Of 8 DP residents, 6 practiced 5 basic VR tasks (median 1 trial to pass), and 7 of 8 practiced 2 advanced tasks (median 4 trials to pass). A curriculum of deliberate individualized practice on a VR simulator improves technical performance in the OR. This has implications to greatly improve the feasibility of implementing simulation-based curricula in residency training

46 CFR 12.611 - Requirements to qualify for an STCW endorsement as electro-technical rating (ETR) on vessels...

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 1 2014-10-01 2014-10-01 false Requirements to qualify for an STCW endorsement as electro-technical rating (ETR) on vessels powered by main propulsion machinery of 750 kW/1,000 HP or more... propulsion machinery of 750 kW/1,000 HP or more. (a) To qualify for an STCW endorsement as an electro...

Development of Airport Surface Required Navigation Performance (RNP)

NASA Technical Reports Server (NTRS)

Cassell, Rick; Smith, Alex; Hicok, Dan

1999-01-01

The U.S. and international aviation communities have adopted the Required Navigation Performance (RNP) process for defining aircraft performance when operating the en-route, approach and landing phases of flight. RNP consists primarily of the following key parameters - accuracy, integrity, continuity, and availability. The processes and analytical techniques employed to define en-route, approach and landing RNP have been applied in the development of RNP for the airport surface. To validate the proposed RNP requirements several methods were used. Operational and flight demonstration data were analyzed for conformance with proposed requirements, as were several aircraft flight simulation studies. The pilot failure risk component was analyzed through several hypothetical scenarios. Additional simulator studies are recommended to better quantify crew reactions to failures as well as additional simulator and field testing to validate achieved accuracy performance, This research was performed in support of the NASA Low Visibility Landing and Surface Operations Programs.

Technical tips to perform safe and effective ultrasound guided steroid joint injections in children.

PubMed

Parra, Dimitri A

2015-01-01

The aim of this article is to describe the technique used to perform ultrasound guided steroid joint injections in children in a group of joints that can be injected using ultrasound as the only image guidance modality. The technique is described and didactic figures are provided to illustrate key technical concepts. It is very important to be familiar with the sonographic appearance of the pediatric joints and the developing bone when performing ultrasound-guided joint injections in children.

Can We Predict Technical Aptitude?: A Systematic Review.

PubMed

Louridas, Marisa; Szasz, Peter; de Montbrun, Sandra; Harris, Kenneth A; Grantcharov, Teodor P

2016-04-01

To identify background characteristics and cognitive tests that may predict surgical trainees' future technical performance, and therefore be used to supplement existing surgical residency selection criteria. Assessment of technical skills is not commonly incorporated as part of the selection process for surgical trainees in North America. Emerging evidence, however, suggests that not all trainees are capable of reaching technical competence. Therefore, incorporating technical aptitude into selection processes may prove useful. A systematic search was carried out of the MEDLINE, PsycINFO, and Embase online databases to identify all studies that assessed associations between surrogate markers of innate technical abilities in surgical trainees, and whether these abilities correlate with technical performance. The quality of each study was evaluated using the Grading of Recommendations, Assessment, Development, and Evaluation system. A total of 8035 records were identified. After screening by title, abstract, and full text, 52 studies were included. Very few surrogate markers were found to predict technical performance. Significant associations with technical performance were seen for 1 of 23 participant-reported surrogate markers, 2 of 25 visual spatial tests, and 2 of 19 dexterity tests. The assessment of trainee Basic Performance Resources predicted technical performance in 62% and 75% of participants. To date, no single test has been shown to reliably predict the technical performance of surgical trainees. Strategies that rely on assessing multiple innate abilities, their interaction, and their relationship with technical skill may ultimately be more likely to serve as reliable predictors of future surgical performance.

29 CFR 1620.15 - Jobs requiring equal skill in performance.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 29 Labor 4 2012-07-01 2012-07-01 false Jobs requiring equal skill in performance. 1620.15 Section... EQUAL PAY ACT § 1620.15 Jobs requiring equal skill in performance. (a) In general. The jobs to which the equal pay standard is applicable are jobs requiring equal skill in their performance. Where the amount...

29 CFR 1620.15 - Jobs requiring equal skill in performance.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 29 Labor 4 2013-07-01 2013-07-01 false Jobs requiring equal skill in performance. 1620.15 Section... EQUAL PAY ACT § 1620.15 Jobs requiring equal skill in performance. (a) In general. The jobs to which the equal pay standard is applicable are jobs requiring equal skill in their performance. Where the amount...

29 CFR 1620.15 - Jobs requiring equal skill in performance.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 4 2014-07-01 2014-07-01 false Jobs requiring equal skill in performance. 1620.15 Section... EQUAL PAY ACT § 1620.15 Jobs requiring equal skill in performance. (a) In general. The jobs to which the equal pay standard is applicable are jobs requiring equal skill in their performance. Where the amount...

29 CFR 1620.15 - Jobs requiring equal skill in performance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 4 2010-07-01 2010-07-01 false Jobs requiring equal skill in performance. 1620.15 Section... EQUAL PAY ACT § 1620.15 Jobs requiring equal skill in performance. (a) In general. The jobs to which the equal pay standard is applicable are jobs requiring equal skill in their performance. Where the amount...

Technical Assistance Needs Assessments (TANAs)

EPA Pesticide Factsheets

The Technical Assistance Needs Assessment (TANA) is a process to identify whether a community requires additional support from EPA in order to understand technical information and have meaningful participation in the Superfund decision-making process.

Technical indicators of economic performance in dairy sheep farming.

PubMed

Theodoridis, A; Ragkos, A; Roustemis, D; Arsenos, G; Abas, Z; Sinapis, E

2014-01-01

In this study, the level of technical efficiency of 58 sheep farms rearing the Chios breed in Greece was measured through the application of the stochastic frontier analysis method. A Translog stochastic frontier production function was estimated using farm accounting data of Chios sheep farms and the impact of various socio-demographic and biophysical factors on the estimated efficiency of the farms was evaluated. The farms were classified into efficiency groups on the basis of the estimated level of efficiency and a technical and economic descriptive analysis was applied in order to illustrate an indicative picture of their structure and productivity. The results of the stochastic frontier model indicate that there are substantial production inefficiencies among the Chios sheep farms and that these farms could increase their production through the improvement of technical efficiency, whereas the results of the inefficiency effects model reveal that the farm-specific explanatory factors can partly explain the observed efficiency differentials. The measurement of technical inefficiency and the detection of its determinants can be used to form the basis of policy recommendations that could contribute to the development of the sector.

Technical quality of root canal treatment performed by undergraduate students using hand instrumentation: a meta-analysis.

PubMed

Ribeiro, D M; Réus, J C; Felippe, W T; Pacheco-Pereira, C; Dutra, K L; Santos, J N; Porporatti, A L; De Luca Canto, G

2018-03-01

The technical quality of root canal treatment (RCT) may impact on the outcome. The quality of education received during undergraduate school may be linked to the quality of treatment provided in general dental practice. In this context, the aim of this systematic review was to answer the following focused questions: (i) What is the frequency of acceptable technical quality of root fillings, assessed radiographically, performed by undergraduate students? (ii) What are the most common errors assessed radiographically and reported in these treatments? For this purpose, articles that evaluated the quality of root fillings performed by undergraduate students were selected. Data were collected based on predetermined criteria. The key features from the included studies were extracted. GRADE-tool assessed the quality of the evidence. MAStARI evaluated the methodological quality, and a meta-analysis on all studies was conducted. At the end of the screening, 24 articles were identified. Overall frequency of acceptable technical quality of root fillings was 48%. From this total, 52% related to anterior teeth, 49% to premolars and 26% to molars. The main procedural errors reported were ledge formation, furcation perforation, apical transportation and apical perforation. The heterogeneity amongst the studies was high (84-99%). Five studies had a high risk of bias, eight had a moderate risk, and 11 had low risk. The overall quality of evidence identified was very low. The conclusion was that technical quality of root fillings performed by undergraduate students is low, which may reveal that endodontic education has limited achievement at undergraduate level. A plan to improve the quality of root fillings, and by extrapolation the overall quality of root canal treatment, should be discussed by the staff responsible for endodontic education and training. © 2017 International Endodontic Journal. Published by John Wiley & Sons Ltd.

24 CFR 891.175 - Technical assistance.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Technical assistance. 891.175... Requirements § 891.175 Technical assistance. For purposes of the Section 202 Program and the Section 811 Program, the Secretary shall make available appropriate technical assistance to assure that applicants...

5 CFR 9901.405 - Performance management system requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... management system for NSPS employees, subject to the requirements set forth in this subpart. (b) The NSPS performance management system— (1) Provides for the appraisal of the performance of each employee annually; (2... employees based on performance and contribution; (3) Foster and reward excellent performance; (4) Address...

Technology and development requirements for advanced coal conversion systems

NASA Technical Reports Server (NTRS)

1981-01-01

A compendium of coal conversion process descriptions is presented. The SRS and MC data bases were utilized to provide information paticularly in the areas of existing process designs and process evaluations. Additional information requirements were established and arrangements were made to visit process developers, pilot plants, and process development units to obtain information that was not otherwise available. Plant designs, process descriptions and operating conditions, and performance characteristics were analyzed and requirements for further development identified and evaluated to determine the impact of these requirements on the process commercialization potential from the standpoint of economics and technical feasibility. A preliminary methodology was established for the comparative technical and economic assessment of advanced processes.

Report of the Education Technical Subcommittee on Food/Beverage Occupations.

ERIC Educational Resources Information Center

Oregon State Dept. of Education, Salem. Div. of Vocational Education.

Written by a technical committee of persons from industry, professional associations, and labor, as well as persons with special expertise, state officials, and educators in Oregon, this document lists the skills and knowledge required of employees in food and beverage occupations. It also identifies the industry standards (performance objectives)…

Army Officer Job Analysis: Identifying Performance Requirements to Inform Officer Selection and Assignment

DTIC Science & Technology

2011-08-01

ABSTRACT (Maximum 200 words): This report includes lists of leadership and technical duties performed by all Army officers and the skills...proficiency, and we called these Major Duties (MDs). We compiled lists of major duties (MDs) performed by all officers in each of the five positions...26  TABLE 4.1. NUMBER OF SMES WHO REVIEWED DESCRIPTOR LISTS ACROSS ALL SITES

7 CFR 1469.9 - Technical assistance.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Technical assistance. 1469.9 Section 1469.9... Provisions § 1469.9 Technical assistance. (a) NRCS may use the services of NRCS-approved or certified Technical Service Providers in performing its responsibilities for technical assistance. (b) Technical...

Cognitive training for technical and non-technical skills in robotic surgery: a randomised controlled trial.

PubMed

Raison, Nicholas; Ahmed, Kamran; Abe, Takashige; Brunckhorst, Oliver; Novara, Giacomo; Buffi, Nicolò; McIlhenny, Craig; van der Poel, Henk; van Hemelrijck, Mieke; Gavazzi, Andrea; Dasgupta, Prokar

2018-05-07

To investigate the effectiveness of motor imagery (MI) for technical skill and non-technical skill (NTS) training in minimally invasive surgery (MIS). A single-blind, parallel-group randomised controlled trial was conducted at the Vattikuti Institute of Robotic Surgery, King's College London. Novice surgeons were recruited by open invitation in 2015. After basic robotic skills training, participants underwent simple randomisation to either MI training or standard training. All participants completed a robotic urethrovesical anastomosis task within a simulated operating room. In addition to the technical task, participants were required to manage three scripted NTS scenarios. Assessment was performed by five blinded expert surgeons and a NTS expert using validated tools for evaluating technical skills [Global Evaluative Assessment of Robotic Skills (GEARS)] and NTS [Non-Technical Skills for Surgeons (NOTSS)]. Quality of MI was assessed using a revised Movement Imagery Questionnaire (MIQ). In all, 33 participants underwent MI training and 29 underwent standard training. Interrater reliability was high, Krippendorff's α = 0.85. After MI training, the mean (sd) GEARS score was significantly higher than after standard training, at 13.1 (3.25) vs 11.4 (2.97) (P = 0.03). There was no difference in mean NOTSS scores, at 25.8 vs 26.4 (P = 0.77). MI training was successful with significantly higher imagery scores than standard training (mean MIQ score 5.1 vs 4.5, P = 0.04). Motor imagery is an effective training tool for improving technical skill in MIS even in novice participants. No beneficial effect for NTS was found. © 2018 The Authors BJU International © 2018 BJU International Published by John Wiley & Sons Ltd.

The Maternal-to-Zygotic Transition in Higher Plants: Available Approaches, Critical Limitations, and Technical Requirements.

PubMed

Zhao, Peng; Sun, Meng-Xiang

2015-01-01

Fertilization marks the turnover from the gametophyte to sporophyte generation in higher plants. After fertilization, sporophytic development undergoes genetic turnover from maternal to zygotic control: the maternal-to-zygotic transition (MZT). The MZT is thought to be critical for early embryogenesis; however, little is known about the time course or developmental impact of the MZT in higher plants. Here, we discuss what is known in the field and focus on techniques used in relevant studies and their limitations. Some significant questions and technical requirements for further investigations are also discussed. © 2015 Elsevier Inc. All rights reserved.

King 2 2519 ATM residual gyros: Reestablishing 5 year life requirements

NASA Technical Reports Server (NTRS)

Kayal, B.; Carbocci, L. J.

1978-01-01

The technical expertise required to assess the condition of the residual ATM 2519 Singer gyros is discussed. Past build history records, past performance characteristics, and recommendations for particular tests (which were performed by NASA personnel) are summarized. Test results are analyzed. A study of motor performance data and recommendations concerning gyro spin bearing life was performed. A method of reestablishing potential reliability of the bearing for the 5-year life requirement of the power module is also included.

Developing Technical Skill Assessments

ERIC Educational Resources Information Center

Hyslop, Alisha

2009-01-01

One of the biggest challenges facing the career and technical education (CTE) community as it works to implement the 2006 Perkins Act is responding to more rigorous requirements for reporting on CTE students' technical skill attainment. The U.S. Department of Education suggested in non-regulatory guidance that states and locals use the number of…

5 CFR 9701.405 - Performance management system requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... performance management systems for DHS employees, subject to the requirements set forth in this subpart. (b) Each DHS performance management system must— (1) Specify the employees covered by the system(s); (2... 5 Administrative Personnel 3 2013-01-01 2013-01-01 false Performance management system...

5 CFR 9701.405 - Performance management system requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... performance management systems for DHS employees, subject to the requirements set forth in this subpart. (b) Each DHS performance management system must— (1) Specify the employees covered by the system(s); (2... 5 Administrative Personnel 3 2011-01-01 2011-01-01 false Performance management system...

5 CFR 9701.405 - Performance management system requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... performance management systems for DHS employees, subject to the requirements set forth in this subpart. (b) Each DHS performance management system must— (1) Specify the employees covered by the system(s); (2... 5 Administrative Personnel 3 2012-01-01 2012-01-01 false Performance management system...

5 CFR 9701.405 - Performance management system requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... performance management systems for DHS employees, subject to the requirements set forth in this subpart. (b) Each DHS performance management system must— (1) Specify the employees covered by the system(s); (2... 5 Administrative Personnel 3 2014-01-01 2014-01-01 false Performance management system...

TECHNICAL MANPOWER IN NEW YORK STATE. VOLUME II.

ERIC Educational Resources Information Center

AMATULLI, ANGELO; AND OTHERS

THE JOB CONTENT OF THE TECHNICAL OCCUPATIONS AND THE TECHNICAL SKILLS AND SUBJECT MATTER KNOWLEDGES REQUIRED ARE BASED PRIMARILY ON INFORMATION SUPPLIED BY EMPLOYERS FROM 17,414 ESTABLISHMENTS IN NEW YORK STATE. DATA ARE ALSO GIVEN ON GRADE STRUCTURE, EDUCATION AND EXPERIENCE REQUIREMENTS, TESTS AND LICENSES REQUIRED FOR THE JOB, SOURCES OF…

Technical Skill Attainment and Post-Program Outcomes: An Analysis of Pennsylvania Secondary Career and Technical Education Graduates

ERIC Educational Resources Information Center

Staklis, Sandra; Klein, Steven

2010-01-01

Since the mid-1990s, the Pennsylvania Department of Education (PDE) has required all students concentrating in career and technical education (CTE) programs to complete a standardized technical skill assessment at or near the end of their program. Results of technical skill assessments are used for a number of purposes, including recognizing…

Technical Submission Form: Technical Specification of a Wave Energy Farm.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roberts, Jesse D.; Nielsen, Kim; Kennedy, Ben

The Wave - SPARC project developed the Technology Performance Level (TPL) assessment procedure based on a rigorous Systems Engineering exercise. The TPL assessment allows a whole system evaluation of Wave Energy Conversion Technology by measuring it against the requirements determined through the Systems Engineering exercise. The TPL assessment is intended to be useful in technology evaluation; in technology innovation; in allocation of public or priva te investment, and; in making equipment purchasing decisions. This Technical Submission Form (TSF) serves the purpose of collecting relevant and complete information, in a technology agnostic way, to allow TPL assessment s to be mademore » by third party assessor s. The intended usage of this document is that the organization or people that are performing the role of developers or promoters of a particular technology will use this form to provide the information necessary for the organization or people who are perf orming the assessor role to use the TPL assessment.« less

48 CFR 952.242-70 - Technical direction.

Code of Federal Regulations, 2011 CFR

2011-10-01

.... (3) Reviewing and, where required by the contract, approving, technical reports, drawings... 48 Federal Acquisition Regulations System 5 2011-10-01 2011-10-01 false Technical direction. 952... FORMS SOLICITATION PROVISIONS AND CONTRACT CLAUSES Text of Provisions and Clauses 952.242-70 Technical...

48 CFR 952.242-70 - Technical direction.

Code of Federal Regulations, 2012 CFR

2012-10-01

.... (3) Reviewing and, where required by the contract, approving, technical reports, drawings... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Technical direction. 952... FORMS SOLICITATION PROVISIONS AND CONTRACT CLAUSES Text of Provisions and Clauses 952.242-70 Technical...

48 CFR 952.242-70 - Technical direction.

Code of Federal Regulations, 2014 CFR

2014-10-01

.... (3) Reviewing and, where required by the contract, approving, technical reports, drawings... 48 Federal Acquisition Regulations System 5 2014-10-01 2014-10-01 false Technical direction. 952... FORMS SOLICITATION PROVISIONS AND CONTRACT CLAUSES Text of Provisions and Clauses 952.242-70 Technical...

48 CFR 952.242-70 - Technical direction.

Code of Federal Regulations, 2013 CFR

2013-10-01

.... (3) Reviewing and, where required by the contract, approving, technical reports, drawings... 48 Federal Acquisition Regulations System 5 2013-10-01 2013-10-01 false Technical direction. 952... FORMS SOLICITATION PROVISIONS AND CONTRACT CLAUSES Text of Provisions and Clauses 952.242-70 Technical...

14 CFR 171.321 - DME and marker beacon performance requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false DME and marker beacon performance... (MLS) § 171.321 DME and marker beacon performance requirements. (a) The DME equipment must meet the..._regulations/ibr_locations.html. (b) MLS marker beacon equipment must meet the performance requirements...

Which non-technical skills do junior doctors require to prescribe safely? A systematic review.

PubMed

Dearden, Effie; Mellanby, Edward; Cameron, Helen; Harden, Jeni

2015-12-01

Prescribing errors are a major source of avoidable morbidity and mortality. Junior doctors write most in-hospital prescriptions and are the least experienced members of the healthcare team. This puts them at high risk of error and makes them attractive targets for interventions to improve prescription safety. Error analysis has shown a background of complex environments with multiple contributory conditions. Similar conditions in other high risk industries, such as aviation, have led to an increased understanding of so-called human factors and the use of non-technical skills (NTS) training to try to reduce error. To date no research has examined the NTS required for safe prescribing. The aim of this review was to develop a prototype NTS taxonomy for safe prescribing, by junior doctors, in hospital settings. A systematic search identified 14 studies analyzing prescribing behaviours and errors by junior doctors. Framework analysis was used to extract data from the studies and identify behaviours related to categories of NTS that might be relevant to safe and effective prescribing performance by junior doctors. Categories were derived from existing literature and inductively from the data. A prototype taxonomy of relevant categories (situational awareness, decision making, communication and team working, and task management) and elements was constructed. This prototype will form the basis of future work to create a tool that can be used for training and assessment of medical students and junior doctors to reduce prescribing error in the future. © 2015 The British Pharmacological Society.

14 CFR 151.53 - Performance of construction work: Labor requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Performance of construction work: Labor... § 151.53 Performance of construction work: Labor requirements. A sponsor who is required to include in a... during the performance of work under the contract, to the extent necessary to determine whether the...

Getting Personal: Individuality, Innovation, and Technical Communication.

ERIC Educational Resources Information Center

Steiner, Carol J.

1999-01-01

Suggests that effective communication between technical and nontechnical people is difficult because technical communication lacks a personal dimension: technical people give up their identity to be considered competent. Argues that a different approach to communication education for scientists, engineers, and technologists is required to equip…

Performance of Retrained Airmen in Air Force Technical Schools (Revised). Interim Report for Period January 1981-August 1982.

ERIC Educational Resources Information Center

Skinner, Mary J.; Alley, William E.

Research was conducted to determine the effect of changing occupational specialties on the performance of Air Force retrained enlistees attending basic technical schools. The academic performance and attrition rates of approximately 20,000 retrainees and 230,000 nonprior-service enlistees (nonretrainees) attending 272 schools were compared.…

The Interactive Electronic Technical Manual: Requirements, Current Status, and Implementation. Strategy Considerations.

DTIC Science & Technology

1991-07-01

authoring systems. Concurrently, great strides in computer-aided design and computer-aided maintenance have contributed to this capability. 12 Junod ...J.; William A. Nugent; and L. John Junod . Plan for the Navy/Air Force Test of the Interactive Electronic Technical Manual (IETM) at Cecil Field...AFHRL Logistics and Human Factors Division, WPAFB. Aug 1990. 12. Junod , John L. PY90 Interactive Electronic Technical Manual (IETM) Portable Delivery

Human System Simulation in Support of Human Performance Technical Basis at NPPs

DOE Office of Scientific and Technical Information (OSTI.GOV)

David Gertman; Katya Le Blanc; alan mecham

2010-06-01

This paper focuses on strategies and progress toward establishing the Idaho National Laboratory’s (INL’s) Human Systems Simulator Laboratory at the Center for Advanced Energy Studies (CAES), a consortium of Idaho State Universities. The INL is one of the National Laboratories of the US Department of Energy. One of the first planned applications for the Human Systems Simulator Laboratory is implementation of a dynamic nuclear power plant simulation (NPP) where studies of operator workload, situation awareness, performance and preference will be carried out in simulated control rooms including nuclear power plant control rooms. Simulation offers a means by which to reviewmore » operational concepts, improve design practices and provide a technical basis for licensing decisions. In preparation for the next generation power plant and current government and industry efforts in support of light water reactor sustainability, human operators will be attached to a suite of physiological measurement instruments and, in combination with traditional Human Factors Measurement techniques, carry out control room tasks in simulated advanced digital and hybrid analog/digital control rooms. The current focus of the Human Systems Simulator Laboratory is building core competence in quantitative and qualitative measurements of situation awareness and workload. Of particular interest is whether introduction of digital systems including automated procedures has the potential to reduce workload and enhance safety while improving situation awareness or whether workload is merely shifted and situation awareness is modified in yet to be determined ways. Data analysis is carried out by engineers and scientists and includes measures of the physical and neurological correlates of human performance. The current approach supports a user-centered design philosophy (see ISO 13407 “Human Centered Design Process for Interactive Systems, 1999) wherein the context for task performance along

COMSATCOM service technical baseline strategy development approach using PPBW concept

NASA Astrophysics Data System (ADS)

Nguyen, Tien M.; Guillen, Andy T.

2016-05-01

This paper presents an innovative approach to develop a Commercial Satellite Communications (COMSATCOM) service Technical Baseline (TB) and associated Program Baseline (PB) strategy using Portable Pool Bandwidth (PPBW) concept. The concept involves trading of the purchased commercial transponders' Bandwidths (BWs) with existing commercial satellites' bandwidths participated in a "designated pool bandwidth"3 according to agreed terms and conditions. Space Missile Systems Center (SMC) has been implementing the Better Buying Power (BBP 3.0) directive4 and recommending the System Program Offices (SPO) to own the Program and Technical Baseline (PTB) [1, 2] for the development of flexible acquisition strategy and achieving affordability and increased in competition. This paper defines and describes the critical PTB parameters and associated requirements that are important to the government SPO for "owning" an affordable COMSATCOM services contract using PPBW trading concept. The paper describes a step-by-step approach to optimally perform the PPBW trading to meet DoD and its stakeholders (i) affordability requirement, and (ii) fixed and variable bandwidth requirements by optimizing communications performance, cost and PPBW accessibility in terms of Quality of Services (QoS), Bandwidth Sharing Ratio (BSR), Committed Information Rate (CIR), Burstable Information Rate (BIR), Transponder equivalent bandwidth (TPE) and transponder Net Presence Value (NPV). The affordable optimal solution that meets variable bandwidth requirements will consider the operating and trading terms and conditions described in the Fair Access Policy (FAP).

48 CFR 1852.242-70 - Technical direction.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Direction (SEP 1993) (a) Performance of the work under this contract is subject to the written technical... the Contracting Officer in writing in accordance with NASA FAR Supplement 1842.270. “Technical... in writing by the COTR. (d) The Contractor shall proceed promptly with the performance of technical...

Fluid Balance in Team Sport Athletes and the Effect of Hypohydration on Cognitive, Technical, and Physical Performance.

PubMed

Nuccio, Ryan P; Barnes, Kelly A; Carter, James M; Baker, Lindsay B

2017-10-01

Sweat losses in team sports can be significant due to repeated bursts of high-intensity activity, as well as the large body size of athletes, equipment and uniform requirements, and environmental heat stress often present during training and competition. In this paper we aimed to: (1) describe sweat losses and fluid balance changes reported in team sport athletes, (2) review the literature assessing the impact of hypohydration on cognitive, technical, and physical performance in sports-specific studies, (3) briefly review the potential mechanisms by which hypohydration may impact team sport performance, and (4) discuss considerations for future directions. Significant hypohydration (mean body mass loss (BML) >2%) has been reported most consistently in soccer. Although American Football, rugby, basketball, tennis, and ice hockey have reported high sweating rates, fluid balance disturbances have generally been mild (mean BML <2%), suggesting that drinking opportunities were sufficient for most athletes to offset significant fluid losses. The effect of hydration status on team sport performance has been studied mostly in soccer, basketball, cricket, and baseball, with mixed results. Hypohydration typically impaired performance at higher levels of BML (3-4%) and when the method of dehydration involved heat stress. Increased subjective ratings of fatigue and perceived exertion consistently accompanied hypohydration and could explain, in part, the performance impairments reported in some studies. More research is needed to develop valid, reliable, and sensitive sport-specific protocols and should be used in future studies to determine the effects of hypohydration and modifying factors (e.g., age, sex, athlete caliber) on team sport performance.

Range Flight Safety Requirements

NASA Technical Reports Server (NTRS)

Loftin, Charles E.; Hudson, Sandra M.

2018-01-01

The purpose of this NASA Technical Standard is to provide the technical requirements for the NPR 8715.5, Range Flight Safety Program, in regards to protection of the public, the NASA workforce, and property as it pertains to risk analysis, Flight Safety Systems (FSS), and range flight operations. This standard is approved for use by NASA Headquarters and NASA Centers, including Component Facilities and Technical and Service Support Centers, and may be cited in contract, program, and other Agency documents as a technical requirement. This standard may also apply to the Jet Propulsion Laboratory or to other contractors, grant recipients, or parties to agreements to the extent specified or referenced in their contracts, grants, or agreements, when these organizations conduct or participate in missions that involve range flight operations as defined by NPR 8715.5.1.2.2 In this standard, all mandatory actions (i.e., requirements) are denoted by statements containing the term “shall.”1.3 TailoringTailoring of this standard for application to a specific program or project shall be formally documented as part of program or project requirements and approved by the responsible Technical Authority in accordance with NPR 8715.3, NASA General Safety Program Requirements.

Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stoessel, Chris

2013-11-13

This project developed a new high-performance R-10/high SHGC window design, reviewed market positioning and evaluated manufacturing solutions required for broad market adoption. The project objectives were accomplished by: identifying viable technical solutions based on modeling of modern and potential coating stacks and IGU designs; development of new coating material sets for HM thin film stacks, as well as improved HM IGU designs to accept multiple layers of HM films; matching promising new coating designs with new HM IGU designs to demonstrate performance gains; and, in cooperation with a window manufacturer, assess the potential for high-volume manufacturing and cost efficiency ofmore » a HM-based R-10 window with improved solar heat gain characteristics. A broad view of available materials and design options was applied to achieve the desired improvements. Gated engineering methodologies were employed to guide the development process from concept generation to a window demonstration. The project determined that a slightly de-rated window performance allows formulation of a path to achieve the desired cost reductions to support end consumer adoption.« less

5 CFR 9701.405 - Performance management system requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... requirements. 9701.405 Section 9701.405 Administrative Personnel DEPARTMENT OF HOMELAND SECURITY HUMAN RESOURCES MANAGEMENT SYSTEM (DEPARTMENT OF HOMELAND SECURITY-OFFICE OF PERSONNEL MANAGEMENT) DEPARTMENT OF HOMELAND SECURITY HUMAN RESOURCES MANAGEMENT SYSTEM Performance Management § 9701.405 Performance...

Development of U.S. Government General Technical Requirements for UAS Flight Safety Systems Utilizing the Iridium Satellite Constellation

NASA Technical Reports Server (NTRS)

Murray, Jennifer; Birr, Richard

2010-01-01

This slide presentation reviews the development of technical requirements for Unmanned Aircraft Systems (UAS) utilization of the Iridium Satellite Constellation to provide flight safety. The Federal Aviation Authority (FAA) required an over-the-horizon communication standard to guarantee flight safety before permitting widespread UAS flights in the National Air Space (NAS). This is important to ensure reliable control of UASs during loss-link and over-the-horizon scenarios. The core requirement was to utilize a satellite system to send GPS tracking data and other telemetry from a flight vehicle down to the ground. Iridium was chosen as the system because it is one of the only true satellite systems that has world wide coverage, and the service has a highly reliable link margin. The Iridium system, the flight modems, and the test flight are described.

7 CFR 653.3 - Adaptation of technical standards.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 6 2012-01-01 2012-01-01 false Adaptation of technical standards. 653.3 Section 653.3..., DEPARTMENT OF AGRICULTURE SUPPORT ACTIVITIES TECHNICAL STANDARDS § 653.3 Adaptation of technical standards. Technical standards and criteria developed on a national basis may require special adaptation to meet local...

7 CFR 653.3 - Adaptation of technical standards.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 6 2014-01-01 2014-01-01 false Adaptation of technical standards. 653.3 Section 653.3..., DEPARTMENT OF AGRICULTURE SUPPORT ACTIVITIES TECHNICAL STANDARDS § 653.3 Adaptation of technical standards. Technical standards and criteria developed on a national basis may require special adaptation to meet local...

7 CFR 653.3 - Adaptation of technical standards.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 6 2011-01-01 2011-01-01 false Adaptation of technical standards. 653.3 Section 653.3..., DEPARTMENT OF AGRICULTURE SUPPORT ACTIVITIES TECHNICAL STANDARDS § 653.3 Adaptation of technical standards. Technical standards and criteria developed on a national basis may require special adaptation to meet local...

7 CFR 653.3 - Adaptation of technical standards.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 6 2013-01-01 2013-01-01 false Adaptation of technical standards. 653.3 Section 653.3..., DEPARTMENT OF AGRICULTURE SUPPORT ACTIVITIES TECHNICAL STANDARDS § 653.3 Adaptation of technical standards. Technical standards and criteria developed on a national basis may require special adaptation to meet local...

Carl D. Perkins Vocational and Technical Education Act of 1998, Report to Congress on State Performance, Program Year 2001-2002

ERIC Educational Resources Information Center

US Department of Education, 2004

2004-01-01

The Carl D. Perkins Vocational and Technical Education Act of 1998 (Perkins III) requires, in Section 113(c)(3)(C), that the Secretary provide the appropriate committees of Congress copies of annual reports received by the Department from each eligible agency that receives funds under the Act. Section 113(c)(3)(a) further requires the Secretary…

42 CFR 475.103 - Requirements for performing quality improvement initiatives.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 4 2014-10-01 2014-10-01 false Requirements for performing quality improvement... HEALTH AND HUMAN SERVICES (CONTINUED) QUALITY IMPROVEMENT ORGANIZATIONS QUALITY IMPROVEMENT ORGANIZATIONS Quality Improvement Organizations § 475.103 Requirements for performing quality improvement initiatives...

Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 4

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ulm, Franz-Josef

2000-06-30

OAK-B135 Monitoring the Durability Performance of Concrete in Nuclear Waste Containment. Technical Progress Report No. 4. The analysis of the effect of cracks on the acceleration of the calcium leaching process of cement-based materials has been pursued. During the last period (Technical Progress Report No 3), we have introduced a modeling accounting for the high diffusivity of fractures in comparison with the weak solid material diffusivity. It has been shown through dimensional and asymptotic analysis that small fractures do not significantly accelerate the material aging process. This important result for the overall structural aging kinetics of containment structure has beenmore » developed in a paper submitted to the international journal ''Transport in Porous Media''.« less

Technical Review Board Chairperson Guidelines for Conducting Technical Review Boards for Rocket Testing

DTIC Science & Technology

2011-08-17

to create a guide for technical review board chairperson conducting technical review boards for rocket testing performed by the Air Force Research ...BOARDS FOR ROCKET TESTING   TABLE OF CONTENTS List of Acronyms 1 Abstract 2 Chapter 1. Introduction 3 Introduction and Research Question 3...boards for rocket testing performed by the Air Force Research Laboratory’s Space Missile Propulsion Division located at Edwards Air Force Base in

10 CFR 34.20 - Performance requirements for industrial radiography equipment.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 1 2014-01-01 2014-01-01 false Performance requirements for industrial radiography equipment. 34.20 Section 34.20 Energy NUCLEAR REGULATORY COMMISSION LICENSES FOR INDUSTRIAL RADIOGRAPHY AND RADIATION SAFETY REQUIREMENTS FOR INDUSTRIAL RADIOGRAPHIC OPERATIONS Equipment § 34.20 Performance...

10 CFR 34.20 - Performance requirements for industrial radiography equipment.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 1 2012-01-01 2012-01-01 false Performance requirements for industrial radiography equipment. 34.20 Section 34.20 Energy NUCLEAR REGULATORY COMMISSION LICENSES FOR INDUSTRIAL RADIOGRAPHY AND RADIATION SAFETY REQUIREMENTS FOR INDUSTRIAL RADIOGRAPHIC OPERATIONS Equipment § 34.20 Performance...

10 CFR 34.20 - Performance requirements for industrial radiography equipment.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Performance requirements for industrial radiography equipment. 34.20 Section 34.20 Energy NUCLEAR REGULATORY COMMISSION LICENSES FOR INDUSTRIAL RADIOGRAPHY AND RADIATION SAFETY REQUIREMENTS FOR INDUSTRIAL RADIOGRAPHIC OPERATIONS Equipment § 34.20 Performance...

10 CFR 34.20 - Performance requirements for industrial radiography equipment.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 1 2011-01-01 2011-01-01 false Performance requirements for industrial radiography equipment. 34.20 Section 34.20 Energy NUCLEAR REGULATORY COMMISSION LICENSES FOR INDUSTRIAL RADIOGRAPHY AND RADIATION SAFETY REQUIREMENTS FOR INDUSTRIAL RADIOGRAPHIC OPERATIONS Equipment § 34.20 Performance...

10 CFR 34.20 - Performance requirements for industrial radiography equipment.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 1 2013-01-01 2013-01-01 false Performance requirements for industrial radiography equipment. 34.20 Section 34.20 Energy NUCLEAR REGULATORY COMMISSION LICENSES FOR INDUSTRIAL RADIOGRAPHY AND RADIATION SAFETY REQUIREMENTS FOR INDUSTRIAL RADIOGRAPHIC OPERATIONS Equipment § 34.20 Performance...

The role of non-technical skills in surgery

PubMed Central

Agha, Riaz A.; Fowler, Alexander J.; Sevdalis, Nick

2015-01-01

Non-technical skills are of increasing importance in surgery and surgical training. A traditional focus on technical skills acquisition and competence is no longer enough for the delivery of a modern, safe surgical practice. This review discusses the importance of non-technical skills and the values that underpin successful modern surgical practice. This narrative review used a number of sources including written and online, there was no specific search strategy of defined databases. Modern surgical practice requires; technical and non-technical skills, evidence-based practice, an emphasis on lifelong learning, monitoring of outcomes and a supportive institutional and health service framework. Finally these requirements need to be combined with a number of personal and professional values including integrity, professionalism and compassionate, patient-centred care. PMID:26904193

Developing Performance Based Requirements for Open Architecture Design

DTIC Science & Technology

2006-04-30

Åèìáëáíáçå= oÉëÉ~êÅÜ=póãéçëáìã= DEVELOPING PERFORMANCE BASED REQUIREMENTS FOR OPEN ARCHITECTURE DESIGN Published: 30 April 2006 by Brad Naegle...for Open Architecture Design 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f...Ñçê=áåÑçêãÉÇ=ÅÜ~åÖÉ======= = - 174 - = = Developing Performance Based Requirements for Open Architecture Design Presenter: Brad Naegle, Lieutenant

SREM (Software Requirements Engineering Methodology) Evaluation. Volume 2. Specifications and Technical Data.

DTIC Science & Technology

1984-02-01

and is approved for publication. APPROVED: ’"" " Project Engineer APPROVED:k 1 4 RAYMOND P. URTZ, JR. Acting Technical Director Command and Control ...Technical Director Command and Control Division FOR THE COMMANDER: JOHN A. RITZ Acting Chief, Plans Office If your address has changed or if you wish to be...179 55812203 Denver CO 80201 55812203 I. CONTROLLING OFFICE NAME AND ADDRESS 12. REPORT DATE Rome Air Development Center (COEE) February 1984 Griffiss

Advanced space power requirements and techniques. Task 1: Mission projections and requirements. Volume 1: Technical report

NASA Technical Reports Server (NTRS)

Wolfe, M. G.

1978-01-01

The objectives of this study were to: (1) develop projections of the NASA, DoD, and civil space power requirements for the 1980-1995 time period; (2) identify specific areas of application and space power subsystem type needs for each prospective user; (3) document the supporting and historical base, including relevant cost related measures of performance; and (4) quantify the benefits of specific technology projection advancements. The initial scope of the study included: (1) construction of likely models for NASA, DoD, and civil space systems; (2) generation of a number of future scenarios; (3) extraction of time phased technology requirements based on the scenarios; and (4) cost/benefit analyses of some of the technologies identified.

Surgical volume-to-outcome relationship and monitoring of technical performance in pediatric cardiac surgery.

PubMed

Kalfa, David; Chai, Paul; Bacha, Emile

2014-08-01

A significant inverse relationship of surgical institutional and surgeon volumes to outcome has been demonstrated in many high-stakes surgical specialties. By and large, the same results were found in pediatric cardiac surgery, for which a more thorough analysis has shown that this relationship depends on case complexity and type of surgical procedures. Lower-volume programs tend to underperform larger-volume programs as case complexity increases. High-volume pediatric cardiac surgeons also tend to have better results than low-volume surgeons, especially at the more complex end of the surgery spectrum (e.g., the Norwood procedure). Nevertheless, this trend for lower mortality rates at larger centers is not universal. All larger programs do not perform better than all smaller programs. Moreover, surgical volume seems to account for only a small proportion of the overall between-center variation in outcome. Intraoperative technical performance is one of the most important parts, if not the most important part, of the therapeutic process and a critical component of postoperative outcome. Thus, the use of center-specific, risk-adjusted outcome as a tool for quality assessment together with monitoring of technical performance using a specific score may be more reliable than relying on volume alone. However, the relationship between surgical volume and outcome in pediatric cardiac surgery is strong enough that it ought to support adapted and well-balanced health care strategies that take advantage of the positive influence that higher center and surgeon volumes have on outcome.

SAM Technical Contacts

EPA Pesticide Factsheets

These technical contacts are available to help with questions regarding method deviations, modifications, sample problems or interferences, quality control requirements, the use of alternative methods, or the need to address analytes or sample types.

46 CFR 160.062-3 - Materials, construction, workmanship, and performance requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Materials, construction, workmanship, and performance.... Lifesaving Equipment, Hydraulic and Manual § 160.062-3 Materials, construction, workmanship, and performance requirements. (a) General. The materials, construction, workmanship, and performance requirements shall conform...

Assessing students' performance in software requirements engineering education using scoring rubrics

NASA Astrophysics Data System (ADS)

Mkpojiogu, Emmanuel O. C.; Hussain, Azham

2017-10-01

The study investigates how helpful the use of scoring rubrics is, in the performance assessment of software requirements engineering students and whether its use can lead to students' performance improvement in the development of software requirements artifacts and models. Scoring rubrics were used by two instructors to assess the cognitive performance of a student in the design and development of software requirements artifacts. The study results indicate that the use of scoring rubrics is very helpful in objectively assessing the performance of software requirements or software engineering students. Furthermore, the results revealed that the use of scoring rubrics can also produce a good achievement assessments direction showing whether a student is either improving or not in a repeated or iterative assessment. In a nutshell, its use leads to the performance improvement of students. The results provided some insights for further investigation and will be beneficial to researchers, requirements engineers, system designers, developers and project managers.

Technical Education and Resource Material.

ERIC Educational Resources Information Center

Mills, Marie T.

New approaches and many technical innovations will be required by the junior college to meet the increasing educational needs of technical occupations. A first is information on which the prospective student can base an intelligent choice of occupation. For this he must have a precise job description to determine whether the career fits his…

48 CFR 35.010 - Scientific and technical reports.

Code of Federal Regulations, 2011 CFR

2011-10-01

... SPECIAL CATEGORIES OF CONTRACTING RESEARCH AND DEVELOPMENT CONTRACTING 35.010 Scientific and technical reports. (a) R&D contracts shall require contractors to furnish scientific and technical reports... 48 Federal Acquisition Regulations System 1 2011-10-01 2011-10-01 false Scientific and technical...