Science.gov

Sample records for 06-04-01 decon pad

  1. POST CLOSURE INSPECTION REPORT FOR CORRECTIVE ACTION UNIT 92: AREA 6 DECON PAD FACILITY, NEVADA TEST SITE NEVADA, FOR THE PERIOD JANUARY 2004 - DECEMBER 2004

    SciTech Connect

    BECHTEL NEVADA

    2005-03-01

    This Post-Closure Inspection Report provides an analysis and summary of inspections for Corrective Action Unit (CAU) 92, Area 6 Decon Pond Facility, Nevada Test Site, Nevada. CAU 92 was closed in accordance with the Resource Conservation and Recovery Act (RCRA) Part B Operational Permit (Nevada Division of Environmental Protection, 1995) and the Federal Facility Agreement and Consent Order of 1996 on May 11, 1999. CAU 92 consists of two Corrective Action Sites (CASs): CAS 06-04-01, Decon Pad oil/Water Separator; and CAS 06-05-02, Decontamination Pond (RCRA). Both CASs have use restrictions; however, only CAS 06-05-02, Decontamination Pond (RCRA), requires post-closure inspections. CAS 06-04-01, Decon Pad Oil/Water Separator, is located inside the fence at the Building 6-605 compound. This report covers the annual period January 2004 through December 2004.

  2. Closure Report for Corrective Action Unit 224: Decon Pad and Septic Systems, Nevada Test Site, Nevada

    SciTech Connect

    NSTec Environmental Restoration

    2007-10-01

    Corrective Action Unit (CAU) 224 is located in Areas 02, 03, 05, 06, 11, and 23 of the Nevada Test Site, which is situated approximately 65 miles northwest of Las Vegas, Nevada. CAU 224 is listed in the Federal Facility Agreement and Consent Order (FFACO) of 1996 as Decon Pad and Septic Systems and is comprised of the following nine Corrective Action Sites (CASs): CAS 02-04-01, Septic Tank (Buried); CAS 03-05-01, Leachfield; CAS 05-04-01, Septic Tanks (4)/Discharge Area; CAS 06-03-01, Sewage Lagoons (3); CAS 06-05-01, Leachfield; CAS 06-17-04, Decon Pad and Wastewater Catch; CAS 06-23-01, Decon Pad Discharge Piping; CAS 11-04-01, Sewage Lagoon; and CAS 23-05-02, Leachfield. The Nevada Division of Environmental Protection (NDEP)-approved corrective action alternative for CASs 02-04-01, 03-05-01, 06-03-01, 11-04-01, and 23-05-02 is no further action. As a best management practice, the septic tanks and distribution box were removed from CASs 02-04-01 and 11-04-01 and disposed of as hydrocarbon waste. The NDEP-approved correction action alternative for CASs 05-04-01, 06-05-01, 06-17-04, and 06-23-01 is clean closure. Closure activities for these CASs included removing and disposing of radiologically and pesticide-impacted soil and debris. CAU 224 was closed in accordance with the NDEP-approved CAU 224 Corrective Action Plan (CAP). The closure activities specified in the CAP were based on the recommendations presented in the CAU 224 Corrective Action Decision Document (U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, 2005). This Closure Report documents CAU 224 closure activities. During closure activities, approximately 60 cubic yards (yd3) of mixed waste in the form of soil and debris; approximately 70 yd{sup 3} of sanitary waste in the form of soil, liquid from septic tanks, and concrete debris; approximately 10 yd{sup 3} of hazardous waste in the form of pesticide-impacted soil; approximately 0.5 yd{sup 3} of universal waste in

  3. Corrective Action Decision Document for Corrective Action Unit 224: Decon Pad and Septic Systems Nevada Test Site, Nevada, Rev. No.: 0

    SciTech Connect

    David A. Strand

    2005-05-01

    This Corrective Action Decision Document has been prepared for Corrective Action Unit (CAU) 224, Decon Pad and Septic Systems, in Areas 2, 3, 5, 6, 11, and 23 of the Nevada Test Site, Nevada, in accordance with the ''Federal Facility Agreement and Consent Order'' (1996). Corrective Action Unit 224 is comprised of the following corrective action sites (CASs): (1) 02-04-01, Septic Tank (Buried); (2) 03-05-01, Leachfield; (3) 05-04-01, Septic Tanks (4)/Discharge Area; (4) 06-03-01, Sewage Lagoons (3); (5) 06-05-01, Leachfield; (6) 06-17-04, Decon Pad and Wastewater Catch; (7) 06-23-01, Decon Pad Discharge Piping; (8) 11-04-01, Sewage Lagoon; and (9) 23-05-02, Leachfield. The purpose of this Corrective Action Decision Document is to identify and provide the rationale for the recommendation of a corrective action alternative for the nine CASs within CAU 224. Corrective action investigation activities were performed from August 10, 2004, through January 18, 2005, as set forth in the CAU 224 Corrective Action Investigation Plan.

  4. Corrective Action Investigation Plan for Corrective Action Unit 224: Decon Pad and Septic Systems Nevada Test Site, Nevada, Rev. No.: 0, with ROTC 1 and 2

    SciTech Connect

    David A. Strand

    2004-04-01

    This Corrective Action Investigation Plan (CAIP) contains project-specific information including facility descriptions, environmental sample collection objectives, and criteria for conducting site investigation activities at Corrective Action Unit (CAU) 224: Decon Pad and Septic Systems, Nevada Test Site (NTS), Nevada. This CAIP has been developed in accordance with the ''Federal Facility Agreement and Consent Order'' (FFACO) (1996) that was agreed to by the State of Nevada, the U.S. Department of Energy (DOE), and the U.S. Department of Defense (DoD). The NTS is approximately 65 miles (mi) northwest of Las Vegas, Nevada (Figure 1-1). Corrective Action Unit 224 is comprised of the nine Corrective Action Sites (CASs) listed below: 02-04-01, Septic Tank (Buried); 03-05-01, Leachfield; 05-04-01, Septic Tanks (4)/Discharge Area; 06-03-01, Sewage Lagoons (3); 06-05-01, Leachfield; 06-17-04, Decon Pad and Wastewater Catch; 06-23-01, Decon Pad Discharge Piping; 11-04-01, Sewage Lagoon; and 23-05-02, Leachfield. Corrective Action Sites 06-05-01, 06-23-01, and 23-05-02 were identified in the 1991 Reynolds Electrical & Engineering Co., Inc. (REECo) inventory (1991). The remaining sites were identified during review of various historical documents. Additional information will be obtained by conducting a corrective action investigation (CAI) prior to evaluating and selecting a corrective action alternative for each CAS. The CAI will include field inspections, radiological and geological surveys, and sample collection. Data will also be obtained to support investigation-derived waste (IDW) disposal and potential future waste management decisions.

  5. Post-Closure Inspection Report for Corrective Action Unit 92: Area 6 Decon Pond Facility

    SciTech Connect

    NSTec Environmental Restoration

    2008-03-01

    This Post-Closure Inspection Report provides an analysis and summary of inspections for Corrective Action Unit (CAU) 92, Area 6 Decon Pond Facility. CAU 92 was closed according to the Resource Conservation and Recovery Act (RCRA) Part B Operational Permit (Nevada Division of Environmental Protection [NDEP], 1995) and the Federal Facility Agreement and Consent Order (FFACO) of 1996 (FFACO, 1996; as amended January 2007). Closure activities were completed on February 16, 1999, and the Closure Report (U.S. Department of Energy, Nevada Operations Office, 1999) was approved and a Notice of Completion issued by NDEP on May 11, 1999. CAU 92 consists of two Corrective Action Sites (CASs): CAS 06-04-01, Decon Pad Oil/Water Separator, and CAS 06-05-02, Decontamination Pond (RCRA). Both CASs have use restrictions; however, only CAS 06-05-02 requires post-closure inspections. Visual inspections of the cover and fencing at CAS 06-05-02 are performed quarterly. Additional inspections are conducted if precipitation occurs in excess of 1.28 centimeters (cm) (0.50 inches [in.]) in a 24-hour period. This report covers calendar year 2007. Quarterly site inspections were performed in March, June, September, and December of 2007. All observations indicated the continued integrity of the unit. No issues or concerns were noted, and no corrective actions were necessary. Copies of the inspection checklists and field notes completed during each inspection are included in Appendix A of this report, and photographs taken during the site inspections are included in Appendix B of this report. Two additional inspections were performed after precipitation events that exceeded 1.28 cm (0.50 in.) within a 24-hour period during 2007. No significant changes in site conditions were noted during these inspections, and no corrective actions were necessary. A copy of the inspection checklists and field notes completed during these additional inspections are included in Appendix A. Precipitation records

  6. Letter Report to Address Comments on the Closure Report for Corrective Action Unit 224: Decon Pad and Septic Systems, Nevada Test Site, Nevada, Revision 0, March 2008

    SciTech Connect

    NSTec Environmental Restoration

    2008-03-17

    The Closure Report (CR) for Corrective Action Unit (CAU) 224, Decon Pad and Septic Systems, was approved by the Nevada Department of Environmental Protection (NDEP) on November 01, 2007. The approval letter contained the following two comments: Comment 1--For 06-05-01, 06-17-04, 06-23-01 provide evidence that the 6 inch VCP pipe originating from building CP-2 is no longer active and sealed to prevent possible future contamination. Comment 2--For the area that includes 06-03-01, provide evidence that active lines are no longer feeding the North and South lagoons and have been sealed to prevent possible future contamination. To address these comments, closure documentation was reviewed, and site visits were conducted to locate and document the areas of concern. Additional fieldwork was conducted in March 2008 to seal the lines and openings described in the two comments. Photographs were taken of the closed drains and lines to document that the NDEP comments were adequately addressed and potential inadvertent discharge to the environment has been eliminated. Investigation and closure documentation was reviewed to identify the locations of potential drains, lines, and other features that could receive and/or transmit liquid. Based on the investigation findings and subsequent closure activities, no openings, distribution boxes, or other features (excluding known floor drains at CP-2) that could receive liquid were found at the CP-2 location (Figure 1), and potential manholes for the north and south sewage lagoons were identified for Corrective Action Site (CAS) 06-03-01 (Figure 2). The distribution box identified in Figure 1 was not located during the investigation and was assumed to have been previously removed.

  7. Post-Closure Inspection Report for Corrective Action Unit 92: Area 6 Decon Pond Facility, Nevada Test Site, Nevada, for Calendar Year 2006

    SciTech Connect

    NSTec Environmental Restoration

    2007-03-01

    This Post-Closure Inspection Report provides an analysis and summary of inspections for Corrective Action Unit (CAU) 92, Area 6 Decon Pond Facility. CAU 92 was closed according to the ''Resource Conservation and Recovery Act'' (RCRA) Part B Operational Permit (Nevada Division of Environmental Protection [NDEP], 1995) and the ''Federal Facility Agreement and Consent Order'' (FFACO) of 1996 (FFACO, 1996). Closure activities were completed on February 16, 1999, and the Closure Report (U.S. Department of Energy, Nevada Operations Office, 1999) was approved and a Notice of Completion issued by NDEP on May 11, 1999. CAU 92 consists of two Corrective Action Sites (CASs), CAS 06-04-01, Decon Pad Oil/Water Separator; and CAS 06-05-02, Decontamination Pond (RCRA). Both CASs have use restrictions; however, only CAS 06-05-02 requires post-closure inspections. Visual inspections of the cover and fencing at CAS 06-05-02 are performed quarterly. Additional inspections are conducted if precipitation occurs in excess of 1.28 centimeters (cm) (0.50 inches [in.]) in a 24-hour period. This report covers calendar year 2006. Quarterly site inspections were performed in March, June, September, and December of 2006. All observations indicated the continued integrity of the unit. No issues or concerns were noted, and no corrective actions were necessary. Copies of the inspection checklists and field notes completed during each inspection are included in Appendix A of this report, and photographs taken during the site inspections are included in Appendix B of this report. One additional inspection was performed after a precipitation event that exceeded 1.28 cm (0.50 in.) within a 24-hour period during 2006. No significant changes in site conditions were noted during this inspection, and no corrective actions were necessary. A copy of the inspection checklist and field notes completed during this additional inspection is included in Appendix A of this report. Precipitation records for 2006

  8. DWPF DECON FRIT SUPERNATE ANALYSIS

    SciTech Connect

    Peeler, D.; Crawford, C.

    2010-09-22

    The Savannah River National Laboratory (SRNL) has been requested to perform analyses on samples of the Defense Waste Processing Facility (DWPF) decon frit slurry (i.e., supernate samples and sump solid samples). Four 1-L liquid slurry samples were provided to SRNL by Savannah River Remediation (SRR) from the 'front-end' decon activities. Additionally, two 1-L sump solids samples were provided to SRNL for compositional and physical analysis. This report contains the results of the supernate analyses, while the solids (sump and slurry) results will be reported in a supplemental report. The analytical data from the decon frit supernate indicate that all of the radionuclide, organic, and inorganic concentrations met the limits in Revision 4 of the Effluent Treatment Plant (ETP) Waste Acceptance Criteria (WAC) with the exception of boron. The ETP WAC limit for boron is 15.0 mg/L while the average measured concentration (based on quadruplicate analysis) was 15.5 mg/L. The measured concentrations of Li, Na, and Si were also relatively high in the supernate analysis. These results are consistent with the relatively high measured value of B given the compositional make-up of Frit 418. Given these results, it was speculated that either (a) Frit 418 was dissolving into the supernate or aqueous fraction and/or (b) fine frit particulates were carried forward to the analytical instrument based on the sampling procedure used (i.e., the supernate samples were not filtered - only settled with the liquid fraction being transferred with a pipette). To address this issue, a filtered supernate sample (using a 0.45 um filter) was prepared and submitted for analysis. The results of the filtered sample were consistent with 'unfiltered or settled' sample - relatively high values of B, Li, Na, and Si were found. This suggests that Frit 418 is dissolving in the liquid phase which could be enhanced by the high surface area of the frit fines or particulates in suspension. Based on the results

  9. Decontamination analysis of the NUWAX-83 accident site using DECON

    SciTech Connect

    Tawil, J.J.

    1983-11-01

    This report presents an analysis of the site restoration options for the NUWAX-83 site, at which an exercise was conducted involving a simulated nuclear weapons accident. This analysis was performed using a computer program deveoped by Pacific Northwest Laboratory. The computer program, called DECON, was designed to assist personnel engaged in the planning of decontamination activities. The many features of DECON that are used in this report demonstrate its potential usefulness as a site restoration planning tool. Strategies that are analyzed with DECON include: (1) employing a Quick-Vac option, under which selected surfaces are vacuumed before they can be rained on; (2) protecting surfaces against precipitation; (3) prohibiting specific operations on selected surfaces; (4) requiring specific methods to be used on selected surfaces; (5) evaluating the trade-off between cleanup standards and decontamination costs; and (6) varying of the cleanup standards according to expected exposure to surface.

  10. DWPF DECON FRIT: SUMP AND SLURRY SOLIDS ANALYSIS

    SciTech Connect

    Crawford, C.; Peeler, D.; Click, D.

    2010-10-20

    The Savannah River National Laboratory (SRNL) has been requested to perform analyses on samples of the Defense Waste Processing Facility (DWPF) decon frit slurry (i.e., supernate samples and sump solid samples). Four 1-L liquid slurry samples were provided to SRNL by Savannah River Remediation (SRR) from the 'front-end' decon activities. Additionally, two 1-L sump solids samples were provided to SRNL for compositional and physical analysis. In this report, the physical and chemical characterization results of the slurry solids and sump solids are reported. Crawford et al. (2010) provide the results of the supernate analysis. The results of the sump solids are reported on a mass basis given the samples were essentially dry upon receipt. The results of the slurry solids were converted to a volume basis given approximately 2.4 grams of slurry solids were obtained from the {approx}4 liters of liquid slurry sample. Although there were slight differences in the analytical results between the sump solids and slurry solids the following general summary statements can be made. Slight differences in the results are also captured for specific analysis. (1) Physical characterization - (a) SEM/EDS analysis suggested that the samples were enriched in Li and Si (B and Na not detectable using the current EDS system) which is consistent with two of the four principle oxides of Frit 418 (B{sub 2}O{sub 3}, Na{sub 2}O, Li{sub 2}O and SiO{sub 2}). (b) SEM/EDS analysis also identified impurities which were elementally consistent with stainless steel (i.e., Fe, Ni, Cr contamination). (c) XRD results indicated that the sump solids samples were amorphous which is consistent with XRD results expected for a Frit 418 based sample. (d) For the sump solids, SEM/EDS analysis indicated that the particle size of the sump solids were consistent with that of an as received Frit 418 sample from a current DWPF vendor. (e) For the slurry solids, SEM/EDS analysis indicated that the particle size range

  11. Pad TPC

    SciTech Connect

    Hilke, H.J.

    1984-01-01

    A new kind of TPC is described, in which no sense wires exist but gas amplification is obtained from a single parallel gap. A mesh separates the drift volume from the amplifying gap. The anode is segmented into circular rows of narrow pads for rphi measurement by centroid finding and into wide circular pads for dE/dx sampling. The expected advantages of this technique are: better, track angle independent rphi resolution (no need for wire pulse height corrections); better two-track separation if more electronic channels can be afforded; less dead space from frame structures; reduced positive feedback and slower chamber deterioration by deposit formation on the anode. Very tight construction tolerances are the principle drawback. The properties of the Pad TPC are discussed in view of large scale construction and first test results are presented.

  12. Peripheral Artery Disease (PAD)

    MedlinePlus

    ... changes and medication . View an animation of atherosclerosis Atherosclerosis and PAD Atherosclerosis is a disease in which plaque builds up ... of an artery. PAD is usually caused by atherosclerosis in the peripheral arteries (or outer regions away ...

  13. PAD_AUDIT -- PAD Auditing Package

    NASA Astrophysics Data System (ADS)

    Clayton, C. A.

    The PAD (Packet Assembler Disassembler) utility is the part of the VAX/VMS Coloured Book Software (CBS) which allows a user to log onto remote computers from a local VAX. Unfortunately, logging into a computer via either the Packet SwitchStream (PSS) or the International Packet SwitchStream (IPSS) costs real money. Some users either do not appreciate this or do not care and have been known to clock up rather large quarterly bills. This software package allows a system manager to determine who has used PAD to call where and (most importantly) how much it has cost. The system manager can then take appropriate action - either charging the individuals, warning them to use the facility with more care or even denying access to a greedy user to one or more sites.

  14. Pad 39B Deconstruction

    NASA Video Gallery

    A time-lapse video of the deconstruction of Launch Pad 39B at NASA's Kennedy Space Center in Florida. The fixed service structure and rotating service structure were removed. Both structures were b...

  15. About Peripheral Artery Disease (PAD)

    MedlinePlus

    ... changes and medication . View an animation of atherosclerosis Atherosclerosis and PAD Atherosclerosis is a disease in which plaque builds up ... of an artery. PAD is usually caused by atherosclerosis in the peripheral arteries (or outer regions away ...

  16. Treating P.A.D.

    MedlinePlus

    ... Home Current Issue Past Issues Special Section Treating P.A.D. Past Issues / Summer 2008 Table of ... is diminished. Illustration courtesy of NHLBI Treatment for P.A.D. is designed to reduce a patient's ...

  17. Treating P.A.D.

    MedlinePlus

    ... Issue Past Issues Special Section Treating P.A.D. Past Issues / Summer 2008 Table of Contents For ... Illustration courtesy of NHLBI Treatment for P.A.D. is designed to reduce a patient's symptoms, prevent ...

  18. Improved Helmet-Padding Material

    NASA Technical Reports Server (NTRS)

    Dawn, Frederic S.; Weiss, Fred R.; Eck, John D.

    1994-01-01

    Polyimide foamed into lightweight padding material for use in helmets. Exhibits increased resistance to ignition, combustion, and impact, and it outgasses less. Foam satisfies offgassing and toxicity requirements of NASA/JSC criteria (NHB80601B). Helmets containing this improved padding material used by firefighters, police, offshore drilling technicians, construction workers, miners, and race-car drivers.

  19. Dual-Mode Adhesive Pad

    NASA Technical Reports Server (NTRS)

    Hartz, Leslie

    1994-01-01

    Tool helps worker grip and move along large, smooth structure with no handgrips or footholds. Adheres to surface but easily released by actuating simple mechanism. Includes handle and segmented contact-adhesive pad. Bulk of pad made of soft plastic foam conforming to surface of structure. Each segment reinforced with rib. In sticking mode, ribs braced by side catches. In peeling mode, side catches retracted, and segmented adhesive pad loses its stiffness. Modified versions useful in inspecting hulls of ships and scaling walls in rescue operations.

  20. Air-cushion lift pad

    NASA Technical Reports Server (NTRS)

    Blaise, H. T.; Dane, D. H.

    1969-01-01

    Mathematical model is formulated for an air pad which is capable of lifting a structure to a height of 0.125 inch. Design is superior to conventional air cushion devices because it eliminates flutter, vibration, heaving, and pitching.

  1. Teaching with iPads

    NASA Astrophysics Data System (ADS)

    Maj, Hubert

    2015-04-01

    Bilingual students in high school with bilingual units in Boguchwała have received iPads for learning English and a few subjects using CLIL (biology, basics of entrepreneurship, geography, IT and mathematics). Lessons with iPads are interesting for students for several reasons. First of all, teenagers like new technologies and using iPads for teaching helps students to learn by fun. Secondly, iPads give new possibilities of looking for knowledge about each theme. Moreover, teaching with iPads develops students' engagement. They have a chance to choose a few among over 65 000 applications for gathering and then presenting information about the lesson topic. They can easily prepare presentations, movies, cartoons, mind maps or whatever they like. Teaching students, thanks to the iPads, makes it their initiative, and the teacher can inspire them to look for the knowledge rather than disciplining pupils. But teaching with iPads is connected with many problems. For instance, there are not any examples on how to teach using these tools. It is very up-to-date technology and teachers firstly must learn the possibilities of iPads and look for new applications. It takes much time, especially at the beginning, and is difficult especially for inexperienced teachers. In addition, it is almost impossible to maintain control of the iPads for all of the students during the lesson. They can use their iPads for something unconnected with the topic of the lesson. Thirdly is lack of time - active methods (with iPads as well) are more time-consuming and it could be that they do not finish the whole program. And of course the last, but not at least, is the problem of money. Some of the applications must be paid for, and it is usually obligatory to possess a credit card. Fortunately, it is not expensive - applications usually cost a few euros and many of them are free and really good.

  2. Air Bearing Lift Pad (ABLP)

    NASA Technical Reports Server (NTRS)

    Dane, Dan H.; Blaise, Herman T.

    1968-01-01

    Typical air bearings float on air films of only a few thousandths of an inch and so will only operate above very smooth, even surfaces. For the mechanical simulation of space, the small drag of the bladder type air pads is much more than can be coped with, and the practicality of large floor areas being machined for precision air bearings is nonexistent. To enable operation above surfaces that undulate slightly or feature cracks and discontinuities, an ABLP has been developed. It consists of a rigid pad beneath which an inflatable bladder is mounted. The bladder is inflated with air which then escapes through passages into a cavity in the center of the bladder to produce the lifting energy. As the air escapes about the perimeter of the bladder, a certain degree of balance and equilibrium is imparted to the pad as it is able to move a limited weight across slightly uneven surfaces.

  3. Studies of Vehicular Padding Materials

    PubMed Central

    Sances, Anthony; Carlin, Fred H.; Herbst, Brian; Forrest, Steve; Meyer, Steve; Khadilkar, Anil; Friedman, Keith; Bish, Jack

    2000-01-01

    The Federal Motor Vehicle Safety Standard 571.201 discusses occupant protection with interior impacts of vehicles. Rule making by the National Highway Traffic Safety Administration (NHTSA) has identified padding for potential injury reduction in vehicles. In these studies, head injury mitigation with padding on vehicular roll bars and brush bars was evaluated. Studies were conducted with free falling Hybrid 50% male head form drops on the fore head and side of the head and a 5% female head. Marked reductions in angular acceleration, as well as Head Injury Criterions (HIC), were observed when compared to unpadded roll bars and brush bars. PMID:11558079

  4. Hump behind the shoulders (Dorsocervical fat pad)

    MedlinePlus

    Buffalo hump; Dorsocervical fat pad ... Cause of dorsocervical fat pad includes any of the following: Certain medicines used to treat HIV or AIDS Long-term use of certain glucocorticoid medicines, ...

  5. Your P.A.D. Checklist

    MedlinePlus

    ... on. Feature: Peripheral Artery Disease Your P.A.D. Checklist Past Issues / Fall 2011 Table of Contents ... your risk of peripheral artery disease (P.A.D.). That can start by making sure you “know ...

  6. Your P.A.D. Checklist

    MedlinePlus

    ... Home Current Issue Past Issues Special Section Your P.A.D. Checklist Past Issues / Summer 2008 Table ... and reduce your risk of peripheral arterial disease (P.A.D.). That can start by making sure ...

  7. Your P.A.D. Checklist

    MedlinePlus

    ... Issue Past Issues Special Section Your P.A.D. Checklist Past Issues / Summer 2008 Table of Contents ... your risk of peripheral arterial disease (P.A.D.). That can start by making sure you "know ...

  8. 21 CFR 878.4440 - Eye pad.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Eye pad. 878.4440 Section 878.4440 Food and Drugs... GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4440 Eye pad. (a) Identification. An eye pad is... use as a bandage over the eye for protection or absorption of secretions. (b) Classification. Class...

  9. 21 CFR 878.4440 - Eye pad.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Eye pad. 878.4440 Section 878.4440 Food and Drugs... GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4440 Eye pad. (a) Identification. An eye pad is... use as a bandage over the eye for protection or absorption of secretions. (b) Classification. Class...

  10. Peripheral Arterial Disease (P.A.D.)

    MedlinePlus

    ... turn Javascript on. Peripheral Artery Disease (P.A.D.) What is P.A.D.? Arteries Clogged With Plaque Peripheral arterial disease (P. ... button on your keyboard.) Why Is P.A.D. Dangerous? Click for more information Blocked blood flow ...

  11. 21 CFR 878.4440 - Eye pad.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Eye pad. 878.4440 Section 878.4440 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4440 Eye pad. (a) Identification. An eye pad...

  12. 21 CFR 878.4440 - Eye pad.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Eye pad. 878.4440 Section 878.4440 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4440 Eye pad. (a) Identification. An eye pad...

  13. 21 CFR 878.4440 - Eye pad.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Eye pad. 878.4440 Section 878.4440 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4440 Eye pad. (a) Identification. An eye pad...

  14. STS-120 on Launch Pad

    NASA Technical Reports Server (NTRS)

    2007-01-01

    A photographer used a fisheye lens attached to an electronic still camera to record a series of photos of the Space Shuttle Discovery at the launch pad while the STS-120 crew was at Kennedy Space Center for the Terminal Countdown Demonstration Test in October 2007. The STS-120 mission launched from Kennedy Space Center's launch pad 39A at 11:38:19 a.m. (EDT) on October 23, 2007. The crew included Scott E. Parazynski, Douglas H. Wheelock, Stephanie D. Wilson, all mission specialists; George D. Zamka, pilot; Pamela A. Melroy, commander; Daniel M. Tani, Expedition 16 flight engineer; and Paolo A. Nespoli, mission specialist representing the European Space Agency (ESA). Major objectives included the installation of the P6 solar array of the port truss and delivery and installment of Harmony, the Italian-built U.S. Node 2 on the International Space Station (ISS).

  15. Launch Pad in a Box

    NASA Technical Reports Server (NTRS)

    Mantovani, J. G.; Tamasy, G. J.; Mueller, R. P.; Townsend, I. I.; Sampson, J. W.; Lane, M. A.

    2016-01-01

    NASA Kennedy Space Center (KSC) is developing a new deployable launch system capability to support a small class of launch vehicles for NASA and commercial space companies to test and launch their vehicles. The deployable launch pad concept was first demonstrated on a smaller scale at KSC in 2012 in support of NASA Johnson Space Center's Morpheus Lander Project. The main objective of the Morpheus Project was to test a prototype planetary lander as a vertical takeoff and landing test-bed for advanced spacecraft technologies using a hazard field that KSC had constructed at the Shuttle Landing Facility (SLF). A steel pad for launch or landing was constructed using a modular design that allowed it to be reconfigurable and expandable. A steel flame trench was designed as an optional module that could be easily inserted in place of any modular steel plate component. The concept of a transportable modular launch and landing pad may also be applicable to planetary surfaces where the effects of rocket exhaust plume on surface regolith is problematic for hardware on the surface that may either be damaged by direct impact of high speed dust particles, or impaired by the accumulation of dust (e.g., solar array panels and thermal radiators). During the Morpheus free flight campaign in 2013-14, KSC performed two studies related to rocket plume effects. One study compared four different thermal ablatives that were applied to the interior of a steel flame trench that KSC had designed and built. The second study monitored the erosion of a concrete landing pad following each landing of the Morpheus vehicle on the same pad located in the hazard field. All surfaces of a portable flame trench that could be directly exposed to hot gas during launch of the Morpheus vehicle were coated with four types of ablatives. All ablative products had been tested by NASA KSC and/or the manufacturer. The ablative thicknesses were measured periodically following the twelve Morpheus free flight tests

  16. Activation of PAD4 in NET formation.

    PubMed

    Rohrbach, Amanda S; Slade, Daniel J; Thompson, Paul R; Mowen, Kerri A

    2012-01-01

    Peptidylarginine deiminases, or PADs, convert arginine residues to the non-ribosomally encoded amino acid citrulline in a variety of protein substrates. PAD4 is expressed in granulocytes and is essential for the formation of neutrophil extracellular traps (NETs) via PAD4-mediated histone citrullination. Citrullination of histones is thought to promote NET formation by inducing chromatin decondensation and facilitating the expulsion of chromosomal DNA that is coated with antimicrobial molecules. Numerous stimuli have been reported to lead to PAD4 activation and NET formation. However, how this signaling process proceeds and how PAD4 becomes activated in cells is largely unknown. Herein, we describe the various stimuli and signaling pathways that have been implicated in PAD4 activation and NET formation, including the role of reactive oxygen species generation. To provide a foundation for the above discussion, we first describe PAD4 structure and function, and how these studies led to the development of PAD-specific inhibitors. A comprehensive survey of the receptors and signaling pathways that regulate PAD4 activation will be important for our understanding of innate immunity, and the identification of signaling intermediates in PAD4 activation may also lead to the generation of pharmaceuticals to target NET-related pathogenesis. PMID:23264775

  17. PAD in women: the ischemic continuum.

    PubMed

    Pollak, Amy West

    2015-06-01

    Lower extremity peripheral arterial disease (PAD) is part of the ischemic continuum of atherosclerotic vascular disease and is associated with an increased risk of myocardial infarction, stroke, and cardiovascular death. Compared to men, women with PAD are more likely to have asymptomatic disease or atypical symptoms. PAD in women is associated with decreased exercise capacity, reduced quality of life, increased risk of depression, as well as a greater risk of acute cardiovascular events and cardiovascular mortality than male counterparts. Ensuring an appropriate diagnosis of women with PAD offers an opportunity to begin risk factor modification therapy, improve walking capacity and make a timely referral for revascularization if needed. It is critical to highlight the sex-based disparities in lower extremity PAD so that we may work to improve outcomes for women with PAD. PMID:25939674

  18. Cantilever mounted resilient pad gas bearing

    NASA Technical Reports Server (NTRS)

    Etsion, I. (Inventor)

    1978-01-01

    A gas-lubricated bearing is described, employing at least one pad mounted on a rectangular cantilever beam to produce a lubricating wedge between the face of the pad and a moving surface. The load-carrying and stiffness characteristics of the pad are related to the dimensions and modulus of elasticity of the beam. The bearing is applicable to a wide variety of types of hydrodynamic bearings.

  19. Learning Chinese Idioms through iPads

    ERIC Educational Resources Information Center

    Yang, Chunsheng; Xie, Ying

    2013-01-01

    This paper reports on an action research study using iPads during the teaching of Chinese idioms to heritage learners. A class of 12 second-year Chinese learners were engaged in a self-generated learning process focused on learning abstract and concrete idioms using iPads. Students' short-term and long-term learning was measured; feedback…

  20. STS-135 Launch Pad Lightning Strike

    NASA Video Gallery

    A pair of lightning strikes occurred near launch pad 39-A at NASA's Kennedy Space Center at 12:31 p.m. and 12:40 p.m. EDT on July 7. The first struck the water tower 515 feet from the pad and the s...

  1. Taking the iPad's Measure

    ERIC Educational Resources Information Center

    Raths, David

    2012-01-01

    Soon after the iPad's release in 2010, several universities decided to issue the devices to all incoming freshmen. At the time, critics scoffed at the moves as little more than marketing gimmicks designed to attract students. In truth, few of the schools required instructors to design curriculum around the iPad or had specific plans to measure…

  2. First Graders with iPads?

    ERIC Educational Resources Information Center

    Getting, Sara; Swainey, Karin

    2012-01-01

    Giving iPads to first graders is a leap of faith that many teachers are understandably hesitant to take, especially if their students need immediate reading intervention and school leaders want guaranteed results. This article discusses how the authors took on the challenge of improving elementary reading using iPads, found surprising success for…

  3. Using iPads to Your Advantage

    ERIC Educational Resources Information Center

    Zakrzewski, Jennifer L.

    2016-01-01

    In this article, middle school mathematics teacher Jennifer Zakrzewski describes how she successfully incorporated iPads and Apple TV (for projection of iPad screens) into her classroom while having her students solve a problem about mangoes. As Zakrzewski began a unit on multiplying and dividing fractions, she chose to start with the Mangoes…

  4. Redstone Missile on Launch Pad

    NASA Technical Reports Server (NTRS)

    1958-01-01

    Redstone missile No. 1002 on the launch pad at Cape Canaveral, Florida, on May 16, 1958. The Redstone ballistic missile was a high-accuracy, liquid-propelled, surface-to-surface missile developed by the Army Ballistic Missile Agency, Redstone Arsenal, in Huntsville, Alabama, under the direction of Dr. von Braun. The Redstone engine was a modified and improved version of the Air Force's Navaho cruise missile engine of the late forties. The A-series, as this would be known, utilized a cylindrical combustion chamber as compared with the bulky, spherical V-2 chamber. By 1951, the Army was moving rapidly toward the design of the Redstone missile, and production was begun in 1952. Redstone rockets became the 'reliable workhorse' for America's early space program. As an example of the versatility, Redstone was utilized in the booster for Explorer 1, the first American satellite, with no major changes to the engine or missile

  5. Lateral pharyngeal fat pad pressure during breathing.

    PubMed

    Winter, W C; Gampper, T; Gay, S B; Suratt, P M

    1996-12-01

    The purpose of this study was to test whether pressure in tissue lateral to the upper airway, the lateral pharyngeal fat pad, differs from atmospheric and pharyngeal pressure and whether it changes with breathing. We studied five male pigs by inserting a transducer-tipped catheter into their fat pad space using computed tomography (CT) scan guidance. We measured airflow with a pneumotachograph attached to a face mask and pharyngeal pressure with a balloon catheter. Fat pad pressure correlated positively with airflow and with pharyngeal pressure, decreasing during inspiration and increasing during expiration. Pressure in the fat pad differed from atmospheric pressure, generally exceeding it, and from pharyngeal pressure. We conclude that lateral pharyngeal fat pad pressure differs from atmospheric and pharyngeal pressure and that it changes with breathing. PMID:9085504

  6. Pad B Liquid Hydrogen Storage Tank

    NASA Technical Reports Server (NTRS)

    Hall, Felicia

    2007-01-01

    Kennedy Space Center is home to two liquid hydrogen storage tanks, one at each launch pad of Launch Complex 39. The liquid hydrogen storage tank at Launch Pad B has a significantly higher boil off rate that the liquid hydrogen storage tank at Launch Pad A. This research looks at various calculations concerning the at Launch Pad B in an attempt to develop a solution to the excess boil off rate. We will look at Perlite levels inside the tank, Boil off rates, conductive heat transfer, and radiant heat transfer through the tank. As a conclusion to the research, we will model the effects of placing an external insulation to the tank in order to reduce the boil off rate and increase the economic efficiency of the liquid hydrogen storage tanks.

  7. Blue Origin Conducts Pad Escape Test

    NASA Video Gallery

    Blue Origin conducted a successful pad escape test Oct. 19 at the company's West Texas launch site, firing its pusher escape motor and launching a full-scale suborbital crew capsule from a simulate...

  8. Traumatic herniation of the buccal fat pad.

    PubMed

    Iehara, Tomoko; Tomoyasu, Chihiro; Nakajima, Hisakazu; Osamura, Toshio; Hosoi, Hajime

    2016-07-01

    Traumatic herniation of the buccal fat pad is a rare traumatic disease. Treatment consists of either excision or replacement. We herein report the first case in which a traumatic herniation of the buccal fat pad healed naturally. It was necessary to differentiate the disease from lipoblastoma. A 17-month-old boy was admitted to a clinic with an intraoral tumor that had suddenly increased in size. The tumor was diagnosed as herniation of the buccal fat pad on pathology of a biopsy specimen. In the present case, the escaped buccal fat body returned naturally and engrafted without dysfunction or facial defects. Given that young children may easily fall down with various objects in their mouth, care is required to prevent traumatic accidents. Traumatic herniation of the buccal fat pad should be considered in the differentiation of tumors of the oral cavity in young children. PMID:26892590

  9. Alining Solder Pads on a Solar Cell

    NASA Technical Reports Server (NTRS)

    Lazzery, A. G.

    1984-01-01

    Mechanism consisting of stylus and hand-operated lever incorporated into screening machine to precisely register front and back solder pads during solar-cell assembly. Technique may interest those assembling solar cells manually for research or prototype work.

  10. The Road to Pad Abort 1

    NASA Video Gallery

    At the White Sands Missile Range in Las Cruces, N.M., engineers and technicians are preparing for the Pad Abort 1 flight test. The Launch Abort System is a sophisticated new rocket tower designed t...

  11. Soyuz Rolled to Launch Pad in Kazakhstan

    NASA Video Gallery

    The Soyuz rocket is rolled out to the launch pad by train on Tuesday, March 26, 2013, at the Baikonur Cosmodrome in Kazakhstan. Launch of the Soyuz rocket is scheduled for March 29 and will send Ex...

  12. Expedition 30 Soyuz Moves to Launch Pad

    NASA Video Gallery

    On Dec. 19, the Soyuz TMA-03M spacecraft and its booster were moved to the launch pad at the Baikonur Cosmodrome in Kazakhstan for final preparations before launch to the International Space Statio...

  13. Knuckle pads – a rare finding

    PubMed Central

    Gengenbacher, Michael; Bianchi, Stefano

    2012-01-01

    Knuckle pads are rare harmless subcutaneous nodules that must be differentiated from joint disease of the proximal interphalangeal or rarely of the metacarpophalangeal joints as well as from other masses of the paraarticular tissues. We present a case of an otherwise healthy 36-year-old woman presenting with bilateral knuckle pads located at the dorsal aspect of the proximal interphalangeal joints. No predisposition to a specific musculoskeletal disorder was noted. Ultrasound revealed well-delimited subcutaneous hypoechoic masses without internal flow signals at color Doppler. Histology showed proliferation of myofibroblasts with a decrease of elastic filaments in the deep dermis. The clinical picture, the family history in addition to the histology allowed us to make the diagnosis of knuckle pads. We present the ultrasound findings of knuckle pads and discuss the differential diagnosis of a “swelling” in the dorsal region of proximal interphalangeal joints and metacarpophalangeal joints. PMID:26672439

  14. Gel pad application for automated breast sonography.

    PubMed

    Kim, Yun Ju; Kim, Sung Hun; Jeh, Su Kyung; Choi, Jae Jeong; Kang, Bong Joo; Song, Byung Joo

    2015-04-01

    The purpose of this study was to describe the technical aspects of gel pad application for automated breast sonography and to show its effects on pain relief, scan coverage, and image quality. Twenty patients underwent 2 sets of automated breast sonography with and without gel pad application and were then asked to provide feedback on the examination-related pain. Scan coverage and image quality were compared quantitatively and qualitatively. The degree of pain was significantly decreased after gel pad application (P < .0001). The scan coverage was expanded particularly at the mid-portion of the breast. Image quality was satisfactory without significant differences between the sets. Gel pad application for automated breast sonography is easy and provides significant pain relief. The scan coverage was expanded, while the image quality was maintained. PMID:25792588

  15. IT Does Not Love iPads

    ERIC Educational Resources Information Center

    Fredette, Michelle

    2013-01-01

    On many campuses, iPads have taken over the hearts and minds of everyone. Everyone, that is, except the IT department. These sexy tablets might be the apple of faculty and students' eyes, but for IT directors and their staffs, working with iPads in an enterprise network environment is not the stuff of a love affair. To state the problem…

  16. Enter the iPad (or Not?)

    ERIC Educational Resources Information Center

    Waters, John K.

    2010-01-01

    Few computing devices have sparked the burning gizmo lust ignited by the iPad. Apple's latest entry into the tablet PC market didn't generate much heat when it was first unveiled in January, but by April 3, the day of the official release, feverish customers were mobbing Apple stores. The company claims to have sold 300,000 iPads by midnight on…

  17. 21 CFR 884.5435 - Unscented menstrual pad.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Unscented menstrual pad. 884.5435 Section 884.5435... § 884.5435 Unscented menstrual pad. (a) Identification. An unscented menstrual pad is a device that is a pad made of cellulosic or synthetic material which is used to absorb menstrual or other...

  18. Reliability Investigations on SnAg Bumps on Substrate Pads with Different Pad Finish

    SciTech Connect

    Bauer, R.; Ebersberger, B.; Kupfer, C.; Alexa, L.

    2006-02-07

    SnAg solder bump is one bump type which is used to replace eutectic SnPb bumps. In this work tests have been done to characterize the reliability properties of this bump type. Electromigration (EM) tests, which were accelerated by high current and high temperature and high temperature storage (HTS) tests were performed. It was found that the reliability properties are sensitive to the material combinations in the interconnect stack. The interconnect stack includes substrate pad, pad finish, bump, underbump metallization (UBM) and the chip pad. Therefore separate test groups for SnAg bumps on Cu substrate pads with organic solderability preservative (OSP) finish and the identical bumps on pads with Ni/Au finish were used. In this paper the reliability test results and the corresponding failure analysis are presented. Some explanations about the differences in formation of intermetallic compounds (IMCs) are given.

  19. Pad testing in incontinent women: a review.

    PubMed

    Ryhammer, A M; Djurhuus, J C; Laurberg, S

    1999-01-01

    This article reviews the literature on pad-weighing tests used for objectifying and quantifying incontinence in urinary incontinent women. The patients wear pads weighed before and after the test period. A weight gain is taken as a measure of the amount of urine loss. The tests are in principle of two different types: short-term office tests and long-term home tests, and measure different aspects of urinary control and dysfunction. Both have an inherent large intra- and interindividual variability. Pad weight gains obtained from patients referred for incontinence and those from self-reported continent controls overlap to a certain degree, and it is not possible to identify distinct numerical cut-off values separating continence from incontinence. This suggests that incontinence is a complex condition in which the amount of leakage, other sources of weight gain, and differences in the individual patients' personal characteristics influence the identification and quantification of the problem. In spite of the shortcomings the pad tests remain a valuable tool for both the clinician and the researcher. The home pad tests are superior to the office tests in terms of authenticity, and should be performed with a concomitant systematic registration of the participant's voidings, fluid intake and episodes of incontinence. PMID:10384973

  20. Phytoalexin-Deficient Mutants of Arabidopsis Reveal That Pad4 Encodes a Regulatory Factor and That Four Pad Genes Contribute to Downy Mildew Resistance

    PubMed Central

    Glazebrook, J.; Zook, M.; Mert, F.; Kagan, I.; Rogers, E. E.; Crute, I. R.; Holub, E. B.; Hammerschmidt, R.; Ausubel, F. M.

    1997-01-01

    We are working to determine the role of the Arabidopsis phytoalexin, camalexin, in protecting the plant from pathogen attack by isolating phytoalexin-deficient (pad) mutants in the accession Columbia (Col-0) and examining their response to pathogens. Mutations in PAD1, PAD2, and PAD4 caused enhanced susceptibility to the bacterial pathogen Pseudomonas syringae pv. maculicola strain ES4326 (PsmES4326), while mutations in PAD3 or PAD5 did not. Camalexin was not detected in any of the double mutants pad1-1 pad2-1, pad1-1 pad3-1 or pad2-1 pad3-1. Growth of PsmES4326 in pad1-1 pad2-1 was greater than that in pad1-1 or pad2-1 plants, while growth in pad1-1 pad3-1 and pad2-1 pad3-1 plants was similar to that in pad1-1 and pad2-1 plants, respectively. The pad4-1 mutation caused reduced camalexin synthesis in response to PsmES4326 infection, but not in response to Cochliobolus carbonum infection, indicating that PAD4 has a regulatory function. PAD1, PAD2, PAD3 and PAD4 are all required for resistance to the eukaryotic biotroph Peronospora parasitica. The pad4-1 mutation caused the most dramatic change, exhibiting full susceptibility to four of six Col-incompatible parasite isolates. Interestingly, each combination of double mutants between pad1-1, pad2-1 and pad3-1 exhibited additive shifts to moderate or full susceptibility to most of the isolates. PMID:9136026

  1. Spacecraft factory-to-pad testing concept

    NASA Technical Reports Server (NTRS)

    Jones, R. H.

    1975-01-01

    It is noted that the concept of factory-to-pad testing is based on the shipment of a flight-ready spacecraft to the launch base and can be achieved by thorough and comprehensive factory testing of the spacecraft. The principal objectives and results of this approach are shown to be significant cost reductions, increased test effectiveness, and fewer flight problems. Key elements for this concept's success are discussed, including factory-to-pad commonality of support equipment, test requirements and procedures, test teams, and computer programs. Applications of this approach in the space-shuttle era are considered, and a preliminary factory-to-pad concept for the Large Space Telescope spacecraft is presented.

  2. Electrostatic Evaluation of the SRB Velostat(Trademark) Pads

    NASA Technical Reports Server (NTRS)

    Buhler, Charles R.; Calle, Carlos I.

    2007-01-01

    During RSRM Grain inspection, pads constructed of Velostat are grounded and installed in the RSRM bore enabling inspectors to move throughout the bore during the inspection. Velostat pads are installed by grounding the first pad installed and subsequent pads are installed overlapping the previously installed pad maintaining a conductive path to facility ground. Pads are removed upon completion of the inspection in a reverse fashion. As the pads are removed scanning of propellant surfaces is performed per OMRS. During PPICI Audit of B5308.006 (Forward Segment Grain Inspection) in October 07 one audit finding noted that electrostatic scanning of propellant surfaces was being performed during removal of conductive pads following grain inspection. ATK does not perform electrostatic scanning of propellant surfaces during pad removal following final inspection at the plant. The integrated team consisting of NASA SE, USA SE, USA QE, ATK LSS, ATK Systems Safety and ATK DE concurred that electrostatic scanning of propellant surfaces was unnecessary as the conductive pads are grounded. Additional time spent in bore performing scanning presents itself as additional risk. Technicians reported that they have never seen any voltage readings while scanning propellant surfaces during pad removal. USA Systems engineering has written KB 17530 in response to the finding which will delete the requirement (item 2 B47GEN.ll0) to scan propellant surfaces during pad removal. As a result of an E3 panel discussion on December 13, 2007, it was decided that verification of the electrical grounding of the Velostat pads be verified.

  3. Padé approximations and diophantine geometry

    PubMed Central

    Chudnovsky, D. V.; Chudnovsky, G. V.

    1985-01-01

    Using methods of Padé approximations we prove a converse to Eisenstein's theorem on the boundedness of denominators of coefficients in the expansion of an algebraic function, for classes of functions, parametrized by meromorphic functions. This result is applied to the Tate conjecture on the effective description of isogenies for elliptic curves. PMID:16593552

  4. Momument at Pad 14 honoring Project Mercury

    NASA Technical Reports Server (NTRS)

    1966-01-01

    Momument at Pad 14 honoring Project Mercury. The Arabic number 7 represents the seven original astronauts. The other figure is the astronomical symbol of the Planet Mercury. In background is the Gemini 12 Agena Target Docking Vehicle atop its Atlas launch vehicle at Cape Kennedy, Florida.

  5. Hemangioma of the buccal fat pad

    PubMed Central

    Hassani, Ali; Saadat, Sarang; Moshiri, Roya; Shahmirzadi, Solaleh

    2014-01-01

    Hemangiomas are benign vascular neoplasms characterized by an abnormal proliferation of blood vessels. Buccal fat pad (BFP) is a rare place for hemangioma. In this report, clinical, radiographic, and histopathological findings are described in a rare case of hemangioma with phleboliths involving the BFP, and a review is made of the international literature on this subject. PMID:24963256

  6. Antares Rolls Out to Wallops Launch Pad

    NASA Video Gallery

    Orbital Sciences Corporation’s Antares rocket rolls out to the launch pad at NASA’s Wallops Flight Facility on the morning of Oct. 1, 2012. Over the next several months, Orbital plans a hot-fir...

  7. Cutting a Tapered Edge on Padding Material

    NASA Technical Reports Server (NTRS)

    Mitchell, M. J.

    1982-01-01

    Resilience and flexibility of felt, rubber, or other padding materials allow them to be clamped in form block, cut straight down, and then released to produce straight clean tapered edge. With material held in slanted position, edge can be cut straight down; hence cut depth is minimum.

  8. Multivariate Padé Approximations For Solving Nonlinear Diffusion Equations

    NASA Astrophysics Data System (ADS)

    Turut, V.

    2015-11-01

    In this paper, multivariate Padé approximation is applied to power series solutions of nonlinear diffusion equations. As it is seen from tables, multivariate Padé approximation (MPA) gives reliable solutions and numerical results.

  9. Prevent P.A.D.: Know Your Numbers

    MedlinePlus

    ... Issue Past Issues Special Section Prevent P.A.D.: Know Your Numbers Past Issues / Summer 2008 Table ... Best "Timely detection and treatment of P.A.D. are critical," says Dr. Patrice Desvigne-Nickens of ...

  10. Biomechanical Comparison of Shorts With Different Pads

    PubMed Central

    Marcolin, Giuseppe; Petrone, Nicola; Reggiani, Carlo; Panizzolo, Fausto A.; Paoli, Antonio

    2015-01-01

    Abstract An intensive use of the bicycle may increase the risk of erectile dysfunction and the compression of the perineal area has been showed to be a major mechanism leading to sexual alterations compromising the quality of life. Manufacturers claim that pads contribute to increase cyclists perineal protection ensuring a high level of comfort. To investigate the influence of various cycling pads with regard to perineal protection and level of comfort. Nine club road cyclists rode 20 min on a drum simulator, located at the Nutrition and Exercise Physiology Laboratory, at a constant speed and gear ratio wearing the shorts with 3 cycling pads of different design and thickness: basic (BAS), intermediate (INT), and endurance (END). Kinematics and pressure data were recorded at min 5, 15, and 20 of the test using a motion capture system and a pressure sensor mat. The variables of interest were: 3-dimensional pelvis excursions, peak pressure, mean pressure, and vertical force. The comfort level was assessed with a ranking order based on the subjects’ perception after the 20-min trials and measuring the vertical ground reaction force under the anterior wheel as well as the length of the center of pressure (COP) trajectory on the saddle. Results showed that the vertical force and the average value of mean pressure on the saddle significantly decreased during the 20-min period of testing for BAS and END. Mean peak pressure on the corresponding perineal cyclist area significantly increased only for BAS during the 20-min period. Interestingly objective comfort indexes measured did not match cyclists subjective comfort evaluation. The lower capacity of BAS to reduce the peak pressure on the corresponding perineal area after 20 min of testing, together with its positive comfort evaluation, suggest that a balance between protection and perceived comfort should be taken into account in the choice of the pad. Hence, the quantitative approach of objective comfort indexes

  11. Rotor stability estimation with competing tilting pad bearing models

    NASA Astrophysics Data System (ADS)

    Cloud, C. Hunter; Maslen, Eric H.; Barrett, Lloyd E.

    2012-05-01

    When predicting the stability of rotors supported by tilting pad journal bearings, it is currently debated whether or not the bearings should be represented with frequency dependent dynamics. Using an experimental apparatus, measurements of pad temperatures, unbalance response and stability are compared with modeling predictions for two tilting pad bearing designs. Predictions based on frequency dependent tilting pad bearing dynamics exhibited significantly better correlation with the stability measurements than those assuming frequency independent dynamics.

  12. 21 CFR 880.5270 - Neonatal eye pad.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Neonatal eye pad. 880.5270 Section 880.5270 Food... § 880.5270 Neonatal eye pad. (a) Identification. A neonatal eye pad is an opaque device used to cover and protect the eye of an infant during therapeutic procedures, such as phototherapy....

  13. 21 CFR 880.5270 - Neonatal eye pad.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Neonatal eye pad. 880.5270 Section 880.5270 Food... § 880.5270 Neonatal eye pad. (a) Identification. A neonatal eye pad is an opaque device used to cover and protect the eye of an infant during therapeutic procedures, such as phototherapy....

  14. 21 CFR 880.5270 - Neonatal eye pad.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Neonatal eye pad. 880.5270 Section 880.5270 Food... § 880.5270 Neonatal eye pad. (a) Identification. A neonatal eye pad is an opaque device used to cover and protect the eye of an infant during therapeutic procedures, such as phototherapy....

  15. 21 CFR 880.5270 - Neonatal eye pad.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Neonatal eye pad. 880.5270 Section 880.5270 Food... § 880.5270 Neonatal eye pad. (a) Identification. A neonatal eye pad is an opaque device used to cover and protect the eye of an infant during therapeutic procedures, such as phototherapy....

  16. 21 CFR 880.5270 - Neonatal eye pad.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Neonatal eye pad. 880.5270 Section 880.5270 Food... § 880.5270 Neonatal eye pad. (a) Identification. A neonatal eye pad is an opaque device used to cover and protect the eye of an infant during therapeutic procedures, such as phototherapy....

  17. A fluopol-ABPP HTS assay to identify PAD inhibitors.

    PubMed

    Knuckley, Bryan; Jones, Justin E; Bachovchin, Daniel A; Slack, Jessica; Causey, Corey P; Brown, Steven J; Rosen, Hugh; Cravatt, Benjamin F; Thompson, Paul R

    2010-10-14

    Protein Arginine Deiminase (PAD) activity is dysregulated in numerous diseases, e.g., Rheumatoid Arthritis. Herein we describe the development of a fluorescence polarization-Activity Based Protein Profiling (fluopol-ABPP) based high throughput screening assay that can be used to identify PAD-selective inhibitors. Using this assay, streptonigrin was identified as a potent, selective, and irreversible PAD4 inactivator. PMID:20740228

  18. iPads in Higher Education--Hype and Hope

    ERIC Educational Resources Information Center

    Nguyen, Lemai; Barton, Siew Mee; Nguyen, Linh Thuy

    2015-01-01

    This paper systematically reviews current research on using iPads in the higher education sector. Since the release of iPads by Apple in 2010, this new technology has been quickly adopted everywhere, especially by the younger generation and professionals. We were motivated to find out how iPads have been adopted for use in the higher education…

  19. Dynamic behavior of air lubricated pivoted-pad journal-bearing, rotor system. 2: Pivot consideration and pad mass

    NASA Technical Reports Server (NTRS)

    Nemeth, Z. N.

    1972-01-01

    Rotor bearing dynamic tests were conducted with tilting-pad journal bearings having three different pad masses and two different pivot geometries. The rotor was vertically mounted and supported by two three-pad tilting-pad gas journal bearings and a simple externally pressurized thrust bearing. The bearing pads were 5.1 cm (2.02 in.) in diameter and 2.8 cm (1.5 in.) long. The length to diameter ratio was 0.75. One pad was mounted on a flexible diaphragm. The bearing supply pressure ranged from 0 to 690 kilonewtons per square meter (0 to 100 psig), and speeds ranged to 38,500 rpm. Heavy mass pad tilting-pad assemblies produced three rotor-bearing resonances above the first two rotor critical speeds. Lower supply pressure eliminated the resonances. The resonances were oriented primarily in the direction normal to the diaphragm.

  20. Miniature tilting pad gas lubricated bearing

    SciTech Connect

    Sixsmith, H.; Swift, W.L.

    1983-12-01

    This paper describes the design and development of a miniature tilting pad gas bearing developed for use in very small turbomachines. The bearings have been developed for cryogenic turboexpanders with shaft diameters down to about 0.3 cm and rotational speeds up to one million rpm. Cryogenic expansion turbines incorporating this type of bearing should be suitable for refrigeration rates down to about 10 w.

  1. A miniature tilting pad gas lubricated bearing

    NASA Astrophysics Data System (ADS)

    Sixsmith, H.; Swift, W. L.

    1983-12-01

    This paper describes the design and development of a miniature tilting pad gas bearing developed for use in very small turbomachines. The bearings have been developed for cryogenic turboexpanders with shaft diameters down to about 0.3 cm and rotational speeds up to one million rpm. Cryogenic expansion turbines incorporating this type of bearing should be suitable for refrigeration rates down to about 10 w.

  2. A miniature tilting pad gas lubricated bearing

    NASA Technical Reports Server (NTRS)

    Sixsmith, H.; Swift, W. L.

    1983-01-01

    This paper describes the design and development of a miniature tilting pad gas bearing developed for use in very small turbomachines. The bearings have been developed for cryogenic turboexpanders with shaft diameters down to about 0.3 cm and rotational speeds up to one million rpm. Cryogenic expansion turbines incorporating this type of bearing should be suitable for refrigeration rates down to about 10 w.

  3. Inflammation of the infrapatellar fat pad.

    PubMed

    Eymard, Florent; Chevalier, Xavier

    2016-07-01

    The infrapatellar fat pad (IFP) of Hoffa's fat pad is the main adipose structure within the knee joint. It is located between the joint capsule and the synovial membrane, which lines its posterior aspect. The IFP is composed chiefly of adipocytes and receives an abundant supply of blood vessels and nerves. Immune cells can infiltrate the IFP, which can become a major source of numerous proinflammatory mediators (cytokines and adipokines). The physiological role for the IFP remains unclear but may involve shock absorption and the protection of adjacent tissues. Hoffa's disease is characterized by inflammation, hypertrophy, and fibrosis of the pad in response to repetitive trauma. Anterior knee pain is the most common symptom. In advanced forms, metaplasia of the IFP may result in the development of a sometimes sizable osteochondroma. The IFP may also contribute to the pathophysiology of knee osteoarthritis, in particular via procatabolic and proinflammatory effects on its synovial lining. Finally, in patients with knee osteoarthritis, inflammation of the IFP may be a source of pain. PMID:27068617

  4. The protein arginine deiminases (PADs): Structure, Function, Inhibition, and Disease

    PubMed Central

    Bicker, Kevin L.

    2012-01-01

    The post translational modification of histones has significant effects on overall chromatin function. One such modification is citrullination, which is catalyzed by the protein arginine deiminases (PADs), a unique family of enzymes that catalyzes the hydrolysis of peptidyl-arginine to form peptidyl-citrulline on histones, fibrinogen, and other biologically relevant proteins. Overexpression and/or increased PAD activity is observed in several diseases, including rheumatoid arthritis, Alzheimer’s disease, multiple sclerosis, lupus, Parkinson’s disease, and cancer. This review discusses the important structural and mechanistic characteristics of the PADs, as well as recent investigations into the role of the PADs in increasing disease severity in RA and colitis and the importance of PAD activity in mediating neutrophil extracellular trap (NET) formation through chromatin decondensation. Lastly, efforts to develop PAD inhibitors with excellent potency, selectivity and in vivo efficacy are discussed, highlighting the most promising inhibitors. PMID:23175390

  5. Soyuz Spacecraft Transported to Launch Pad

    NASA Technical Reports Server (NTRS)

    2003-01-01

    The Soyuz TMA-3 spacecraft and its booster rocket (rear view) is shown on a rail car for transport to the launch pad where it was raised to a vertical launch position at the Baikonur Cosmodrome, Kazakhstan on October 16, 2003. Liftoff occurred on October 18th, transporting a three man crew to the International Space Station (ISS). Aboard were Michael Foale, Expedition-8 Commander and NASA science officer; Alexander Kaleri, Soyuz Commander and flight engineer, both members of the Expedition-8 crew; and European Space agency (ESA) Astronaut Pedro Duque of Spain. Photo Credit: 'NASA/Bill Ingalls'

  6. Soyuz Spacecraft Transported to Launch Pad

    NASA Technical Reports Server (NTRS)

    2003-01-01

    The Soyuz TMA-3 spacecraft and its booster rocket (front view) is shown on a rail car for transport to the launch pad where it was raised to a vertical launch position at the Baikonur Cosmodrome, Kazakhstan on October 16, 2003. Liftoff occurred on October 18th, transporting a three man crew to the International Space Station (ISS). Aboard were Michael Foale, Expedition-8 Commander and NASA science officer; Alexander Kaleri, Soyuz Commander and flight engineer, both members of the Expedition-8 crew; and European Space agency (ESA) Astronaut Pedro Duque of Spain. Photo Credit: 'NASA/Bill Ingalls'

  7. Launch Pad Coatings for Smart Corrosion Control

    NASA Technical Reports Server (NTRS)

    Calle, Luz M.; Hintze, Paul E.; Bucherl, Cori N.; Li, Wenyan; Buhrow, Jerry W.; Curran, Jerome P.; Whitten, Mary C.

    2010-01-01

    Corrosion is the degradation of a material as a result of its interaction with the environment. The environment at the KSC launch pads has been documented by ASM International (formerly American Society for Metals) as the most corrosive in the US. The 70 tons of highly corrosive hydrochloric acid that are generated by the solid rocket boosters during a launch exacerbate the corrosiveness of the environment at the pads. Numerous failures at the pads are caused by the pitting of stainless steels, rebar corrosion, and the degradation of concrete. Corrosion control of launch pad structures relies on the use of coatings selected from the qualified products list (QPL) of the NASA Standard 5008A for Protective Coating of Carbon Steel, Stainless Steel, and Aluminum on Launch Structures, Facilities, and Ground Support Equipment. This standard was developed to establish uniform engineering practices and methods and to ensure the inclusion of essential criteria in the coating of ground support equipment (GSE) and facilities used by or for NASA. This standard is applicable to GSE and facilities that support space vehicle or payload programs or projects and to critical facilities at all NASA locations worldwide. Environmental regulation changes have dramatically reduced the production, handling, use, and availability of conventional protective coatings for application to KSC launch structures and ground support equipment. Current attrition rate of qualified KSC coatings will drastically limit the number of commercial off the shelf (COTS) products available for the Constellation Program (CxP) ground operations (GO). CxP GO identified corrosion detection and control technologies as a critical, initial capability technology need for ground processing of Ares I and Ares V to meet Constellation Architecture Requirements Document (CARD) CxP 70000 operability requirements for reduced ground processing complexity, streamlined integrated testing, and operations phase affordability

  8. Metal pad instabilities in liquid metal batteries

    NASA Astrophysics Data System (ADS)

    Zikanov, Oleg

    2015-12-01

    A mechanical analogy is used to analyze the interaction between the magnetic field, electric current, and deformation of interfaces in liquid metal batteries. In the framework of a low-mode, nondissipative, linear stability model, it is found that, during charging or discharging, a sufficiently large battery is prone to instabilities of two types. One is similar to the metal pad instability known to exist in the aluminum reduction cells. Another type is new. It is related to the destabilizing effect of the Lorentz force formed by the azimuthal magnetic field induced by the base current, and the current perturbations caused by the local variations of the thickness of the electrolyte layer.

  9. Launch Pad Escape System Design (Human Spaceflight)

    NASA Technical Reports Server (NTRS)

    Maloney, Kelli

    2011-01-01

    A launch pad escape system for human spaceflight is one of those things that everyone hopes they will never need but is critical for every manned space program. Since men were first put into space in the early 1960s, the need for such an Emergency Escape System (EES) has become apparent. The National Aeronautics and Space Administration (NASA) has made use of various types of these EESs over the past 50 years. Early programs, like Mercury and Gemini, did not have an official launch pad escape system. Rather, they relied on a Launch Escape System (LES) of a separate solid rocket motor attached to the manned capsule that could pull the astronauts to safety in the event of an emergency. This could only occur after hatch closure at the launch pad or during the first stage of flight. A version of a LES, now called a Launch Abort System (LAS) is still used today for all manned capsule type launch vehicles. However, this system is very limited in that it can only be used after hatch closure and it is for flight crew only. In addition, the forces necessary for the LES/LAS to get the capsule away from a rocket during the first stage of flight are quite high and can cause injury to the crew. These shortcomings led to the development of a ground based EES for the flight crew and ground support personnel as well. This way, a much less dangerous mode of egress is available for any flight or ground personnel up to a few seconds before launch. The early EESs were fairly simple, gravity-powered systems to use when thing's go bad. And things can go bad very quickly and catastrophically when dealing with a flight vehicle fueled with millions of pounds of hazardous propellant. With this in mind, early EES designers saw such a passive/unpowered system as a must for last minute escapes. This and other design requirements had to be derived for an EES, and this section will take a look at the safety design requirements had to be derived for an EES, and this section will take a look at

  10. Russian Soyuz Moves to Launch Pad

    NASA Technical Reports Server (NTRS)

    2000-01-01

    The Soyuz TM-31 launch vehicle, which carried the first resident crew to the International Space Station, moves toward the launch pad at the Baikonur complex in Kazakhstan. The Russian Soyuz launch vehicle is an expendable spacecraft that evolved out of the original Class A (Sputnik). From the early 1960' until today, the Soyuz launch vehicle has been the backbone of Russia's marned and unmanned space launch fleet. Today, the Soyuz launch vehicle is marketed internationally by a joint Russian/French consortium called STARSEM. As of August 2001, there have been ten Soyuz missions under the STARSEM banner.

  11. Mars Science Laboratory Launch Pad Thermal Control

    NASA Technical Reports Server (NTRS)

    Bhandari, Pradeep; Dudik, Brenda; Birur, Gajanana; Bame, David

    2011-01-01

    This paper will describe the challenges faced in accommodating the warm Multi Mission Radioisotope Thermoelectric Generator (MMRTG) during the pre-launch phases of integration, launch pad operations as well as during launch. Predictions of temperatures during these phases will be presented when all the cooling systems (HRS and A/C) are operational. In-air tests conducted on the spacecraft in December 2008 to simulate the launch conditions were very successful and showed that all components would be within their allowable limits during these phases. Results of these tests will be shared in this paper.

  12. Tilting pad gas bearing design for micro gas turbines

    NASA Astrophysics Data System (ADS)

    Nabuurs, M. J. H. W.; Al-Bender, F.; Reynaerts, D.

    2013-12-01

    This paper presents the results of a dynamic stability investigation of a micro gas turbine supported by two flexible tilting pad bearings. The pad flexibility allows centrifugal and thermal shaft growth of the rotor but can also introduce undesirable rotor instabilities. An eigenvalue analysis on the linearised rotor-bearing dynamics is performed to estimate the required pad stiffness and damping for stability. Results of the eigenvalue analysis are evaluated by fully nonlinear orbit simulations.

  13. Measuring pad-pad pinch strength in a non-human primate: Macaca fascicularis.

    PubMed

    Banks, Jacob J; Lavender, Steven A; Buford, John A; Sommerich, Carolyn M

    2007-12-01

    The primary purpose of this study was to establish a methodology for determining and perhaps predicting (via regression analysis of anthropometric measures) Macaca fascicularis isometric pinch strength for a specific task. The larger purpose of this work was to properly scale a pinching task for the monkeys in order to study dose-response relationships in a non-human primate model for carpal tunnel syndrome. Three female and one male macaque (n=4) of varying size and age were trained to perform a left-handed pad-pad pinch. The task required 60 degrees of wrist flexion at a static pinching distance of 3 cm between the thumb and fingers. Subjects were trained for a period of 20-weeks. After that time, an analysis of performance gradients found that they had each reached a plateau in their force output. Pinch strength for the four animals ranged from 29.4 to 59.8 N. Regression analysis revealed that body mass (kg) and wrist circumference (cm) were both predictive of pinch strength, exhibiting adjusted R(2) values of 0.93 (p=0.024) and 0.96 (p=0.015), respectively. Thus, the results suggest that maximal pinch strength could be acceptably estimated in future subjects using either the wrist circumference or the body mass measures, as both were strong predictors of pad-pad pinch strength. PMID:17035044

  14. Tilting pad journal bearings - Measured and predicted stiffness coefficients

    SciTech Connect

    Parkins, D.W.; Horner, D. Michell Bearings, Newcastle-upon-Tyne )

    1993-07-01

    This paper presents measured and calculated characteristics of a tilting pad journal bearing suitable for high speed machinery. Descriptions are given of the experimental techniques used with this variety of bearing and the theoretical model for predicting performance. Measured values of pad temperature, eccentricity, attitude angle, and the four stiffness coefficients are given for a range of loads and rotational speeds. Data are given for both load on pad and between pad configurations, the two principal loading arrangements. Comparisons are made between the measured and predicted bearing temperatures and stiffness coefficients over a wide range of values. 11 refs.

  15. Pad Safety Personnel Launch Support For STS-200

    NASA Technical Reports Server (NTRS)

    Guarino, Jennifer

    2007-01-01

    The launch of a space shuttle is a complex and lengthy procedure. There are many places and components to look at and prepare. The components are the orbiter, solid rocket boosters, external tank, and ground equipment. Some of the places are the launch pad, fuel locations, and surrounding structures. Preparations for a launch include equipment checks, system checks, sniff checks for hazardous commodities, and countless walkdowns. Throughout these preparations, pad safety personnel must always be on call. This requires three shifts of multiple people to be ready when needed. Also, the pad safety personnel must be available for the non-launch tasks that are always present for both launch pads

  16. Tilting pad journal bearings - Measured and predicted stiffness coefficients

    NASA Astrophysics Data System (ADS)

    Parkins, D. W.; Horner, D.

    1993-07-01

    This paper presents measured and calculated characteristics of a tilting pad journal bearing suitable for high speed machinery. Descriptions are given of the experimental techniques used with this variety of bearing and the theoretical model for predicting performance. Measured values of pad temperature, eccentricity, attitude angle, and the four stiffness coefficients are given for a range of loads and rotational speeds. Data are given for both load on pad and between pad configurations, the two principal loading arrangements. Comparisons are made between the measured and predicted bearing temperatures and stiffness coefficients over a wide range of values.

  17. Gecko adhesion pad: a smart surface?

    NASA Astrophysics Data System (ADS)

    Pesika, Noshir S.; Zeng, Hongbo; Kristiansen, Kai; Zhao, Boxin; Tian, Yu; Autumn, Kellar; Israelachvili, Jacob

    2009-11-01

    Recently, it has been shown that humidity can increase the adhesion of the spatula pads that form the outermost (adhesive) surface of the tokay gecko feet by 50% relative to the main adhesion mechanism (i.e. van der Waals adhesive forces), although the mechanism by which the enhancement is realized is still not well understood. A change in the surface hydrophobicity of a gecko setal array is observed when the array, which supports the spatulae, is exposed to a water drop for more than 20 min, suggesting a change in the hydrophilic-lyophilic balance (HLB), and therefore of the conformation of the surface proteins. A surface force apparatus (SFA) was used to quantify these changes, i.e. in the adhesion and friction forces, while shearing the setal array against a silica surface under (i) dry conditions, (ii) 100% humidity and (iii) when fully immersed in water. The adhesion increased in the humid environment but greatly diminished in water. Although the adhesion forces changed significantly, the friction forces remained unaffected, indicating that the friction between these highly textured surfaces is 'load-controlled' rather than 'adhesion-controlled'. These results demonstrate that the gecko adhesive pads have the ability to exploit environmental conditions to maximize their adhesion and stabilize their friction forces. Future designs of synthetic dry adhesives inspired by the gecko can potentially include similar 'smart' surfaces that adapt to their environment.

  18. Launch Pad 39 Hail Monitor Array System

    NASA Technical Reports Server (NTRS)

    2008-01-01

    Weather conditions at Kennedy Space Center are extremely dynamic, and they greatly affect the safety of the Space Shuttles sitting on the launch pads. For example, on May 13, 1999, the foam on the External Tank (ET) of STS-96 was significantly damaged by hail at the launch pad, requiring rollback to the Vehicle Assembly Building. The loss of ET foam on STS-114 in 2005 intensified interest in monitoring and measuring damage to ET foam, especially from hail. But hail can be difficult to detect and monitor because it is often localized and obscured by heavy rain. Furthermore, the hot Florida climate usually melts the hail even before the rainfall subsides. In response, the hail monitor array (HMA) system, a joint effort of the Applied Physics Laboratory operated by NASA and ASRC Aerospace at KSC, was deployed for operational testing in the fall of 2006. Volunteers from the Community Collaborative Rain, Hail, and Snow (CoCoRaHS) network, in conjunction with Colorado State University, continue to test duplicate hail monitor systems deployed in the high plains of Colorado.

  19. 40 CFR 265.442 - Design and installation of new drip pads.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... pads. 265.442 Section 265.442 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED..., STORAGE, AND DISPOSAL FACILITIES Drip Pads § 265.442 Design and installation of new drip pads. Owners and operators of new drip pads must ensure that the pads are designed, installed, and operated in...

  20. 40 CFR 264.572 - Design and installation of new drip pads.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... pads. 264.572 Section 264.572 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... DISPOSAL FACILITIES Drip Pads § 264.572 Design and installation of new drip pads. Owners and operators of new drip pads must ensure that the pads are designed, installed, and operated in accordance with...

  1. Creating Microcomputer Graphics with the KoalaPad.

    ERIC Educational Resources Information Center

    White, Dennis W.

    1985-01-01

    The KoalaPad, an advanced graphic tablet introduced in 1983, reduces the cost and the degree of programing background required to create sophisticated images on the microcomputer. The potentials of the KoalaPad for use in an art education program are discussed, and recommendations for creating a microcomputer graphics lab are presented. (RM)

  2. 50. SOUTHEAST CORNER OF LAUNCH PAD. RAIL AND BUMPER IN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    50. SOUTHEAST CORNER OF LAUNCH PAD. RAIL AND BUMPER IN CENTER OF PHOTOGRAPH; FIRE SUPPRESSION NOZZLES ON RIGHT; THRUST SECTION HEATER DUCT ON LEFT. COMMUNICATIONS HOOKUP FOR THE MST LEFT OF DUCT. - Vandenberg Air Force Base, Space Launch Complex 3, Launch Pad 3 East, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

  3. 14. VIEW OF MST, FACING SOUTHEAST, AND LAUNCH PAD TAKEN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    14. VIEW OF MST, FACING SOUTHEAST, AND LAUNCH PAD TAKEN FROM NORTHEAST PHOTO TOWER WITH WINDOW OPEN. FEATURES LEFT TO RIGHT: SOUTH TELEVISION CAMERA TOWER, SOUTHWEST PHOTO TOWER, LAUNCHER, UMBILICAL MAST, MST, AND OXIDIZER APRON. - Vandenberg Air Force Base, Space Launch Complex 3, Launch Pad 3 East, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

  4. 42. VIEW OF UMBILICAL MAST AND LAUNCH PAD FROM MST ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    42. VIEW OF UMBILICAL MAST AND LAUNCH PAD FROM MST BASE. LAUNCHER IS BEHIND UMBILICAL MAST AND RAIL SYSTEM IS PARALLEL TO MAST ON RIGHT AND LEFT. - Vandenberg Air Force Base, Space Launch Complex 3, Launch Pad 3 East, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

  5. 41. VIEW OF UMBILICAL MAST AND LAUNCH PAD FROM LAUNCHER; ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    41. VIEW OF UMBILICAL MAST AND LAUNCH PAD FROM LAUNCHER; SOUTH FACE OF MST IN BACKGROUND. RAIL SYSTEM FROM BASE OF MST PARALLEL TO MAST. - Vandenberg Air Force Base, Space Launch Complex 3, Launch Pad 3 East, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

  6. iPad Use and Student Engagement in the Classroom

    ERIC Educational Resources Information Center

    Mango, Oraib

    2015-01-01

    iPads and handheld digital devices have been securing their place in educational institutions surrounded by debates between advocates and skeptics. In light of not enough evidence supporting the use of iPads in education, this study examined the ways that college students in two foreign language classrooms perceived the influence of the use of…

  7. 1. GENERAL VIEW OF PAD B MOBILE SERVICE STRUCTURE IN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    1. GENERAL VIEW OF PAD B MOBILE SERVICE STRUCTURE IN SETTING WITH FACILITY 28416 (PAD A MOBILE SERVICE STRUCTURE) IN DISTANCE; VIEW TO NORTHEAST. - Cape Canaveral Air Station, Launch Complex 17, Facility 28417, East end of Lighthouse Road, Cape Canaveral, Brevard County, FL

  8. Effectiveness of Using iPads to Build Math Fluency

    ERIC Educational Resources Information Center

    O'Malley, Patricia; Jenkins, Sandi; Wesley, Brooke; Donehower, Claire; Rabuck, Deidre; Lewis, MEB.

    2013-01-01

    Research into integrating technology such as iPads into the curriculum for students with disabilities is still new. The purpose of this study was to examine the effect of the use of a basic math skill application on an iPad to increase basic math fluency. As part of a classwide academic intervention, the study was conducted with 10 students with…

  9. iPads in Inclusive Classrooms: Ecologies of Learning

    ERIC Educational Resources Information Center

    Meyer, Bente

    2013-01-01

    This paper builds on data from a project where iPads were used in a lower secondary school in Denmark to support school development and inclusive learning environments. The paper explores how iPads enter into and work as part of an ecology of learning in five classes in lower secondary school. The paper argues that we should disengage approaches…

  10. DETAIL OF THE SLOPING CONCRETE PAD AT THE SOUTH SIDE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    DETAIL OF THE SLOPING CONCRETE PAD AT THE SOUTH SIDE OF THE GUN EMPLACEMENT. NOTE ADDED BLOCK OF CAST CONCRETE AT THE LOW (RIGHT) END OF SLOPED PAD. VIEW FACING SOUTHWEST - U.S. Naval Base, Pearl Harbor, Ford Island 5-Inch Antiaircraft Battery, East Gun Emplacement, Ford Island, Pearl City, Honolulu County, HI

  11. iPad use during ward rounds: an observational study.

    PubMed

    Lehnbom, Elin C; Adams, Kristian; Day, Richard O; Westbrook, Johanna I; Baysari, Melissa T

    2014-01-01

    Much clinical information is computerised and doctors' use of mobile devices such as iPad tablets to access this information is expanding rapidly. This study investigated the use of iPads during ward rounds and their usefulness in providing access to information during ward rounds. Ten teams of doctors at a large teaching hospital were given iPads for ten weeks and were observed on ward rounds for 77.3 hours as they interacted with 525 patients. Use of iPads and other information technology devices to access clinical information was recorded. The majority of clinical information was accessed using iPads (56.2%), followed by computers-on-wheels (35.8%), stationary PCs (7.9%) and smartphones (0.1%). Despite having read-only access on iPads, doctors were generally happy using iPads on ward rounds. These findings provide evidence of the value of iPads as a tool to access information at the point of care. PMID:25087529

  12. Teaching with Technology: iPads and Primary Mathematics

    ERIC Educational Resources Information Center

    Attard, Catherine

    2013-01-01

    iPads are beginning to appear in more and more primary classrooms, yet it is difficult to find teaching ideas that promote deep mathematical understanding. Catherine Attard provides a list of teaching considerations to be used when using iPads and two practical ideas for using them.

  13. 49. VIEW OF EAST SIDE OF LAUNCH PAD. THRUST SECTION ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    49. VIEW OF EAST SIDE OF LAUNCH PAD. THRUST SECTION HEATER AND DUCTS ON RIGHT; UMBILICAL MAST POWER CONNECTORS ON LEFT; RAIL SYSTEM AND FIRE SUPPRESSION NOZZLES IN FOREGROUND. - Vandenberg Air Force Base, Space Launch Complex 3, Launch Pad 3 East, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

  14. Topography of whisking II: interaction of whisker and pad.

    PubMed

    Bermejo, R; Friedman, W; Zeigler, H P

    2005-09-01

    The peripheral effector system mediating rodent whisking produces protraction/retraction movements of the whiskers and translation movements of the collagenous mystacial pad. To examine the interaction of these movements during whisking in air we used high-resolution, optoelectronic methods for two-dimensional monitoring of whisker and pad movements in head-fixed rats. Under these testing conditions (1) whisker movements on the same side of the face are synchronous and of similar amplitude; (2) pad movements exhibit the characteristic 'exploratory' rhythm (6-12 Hz) of whisking but their movements often have a low frequency (1-2 Hz) component; (3) Pad movements occur in both antero-posterior and dorso-ventral planes but there are considerable variations in the amplitude and topography of movement parameters in the two planes. We conclude that (a) both whisker and pad receive input from a common central rhythm generator; (b) differences in whisker and pad amplitude and topography probably reflect differences in the biomechanical properties of the structures receiving that input; (c) pad movements make a significant contribution to the kinematics of whisking behavior and (d) the two-dimensional nature of pad translation movements significantly increases the rat's flexible control of its mobile sensor. PMID:16338829

  15. Public access to defibrillation (PAD): implementing a church program.

    PubMed

    Gilchrist, Jody

    2012-01-01

    For every minute without cardiopulmonary resuscitation and defibrillation, the odds of surviving cardiac arrest decrease by 7% to 10%. Churches can implement a public access to defibrillation (PAD) program and help save lives. This article outlines steps and resources for setting up a PAD program. PMID:22480085

  16. Implementing iPads in the Inclusive Classroom Setting

    ERIC Educational Resources Information Center

    Maich, Kimberly; Hall, Carmen

    2016-01-01

    This column provides practical suggestions to help guide teachers in utilizing classroom sets of iPads. Following a brief introduction to tablet technology in inclusive classrooms and the origin of these recommendations from a case study focus group, important elements of setting up classroom iPad use, from finding funding to teaching apps, are…

  17. Open Vehicle Sketch Pad Aircraft Modeling Strategies

    NASA Technical Reports Server (NTRS)

    Hahn, Andrew S.

    2013-01-01

    Geometric modeling of aircraft during the Conceptual design phase is very different from that needed for the Preliminary or Detailed design phases. The Conceptual design phase is characterized by the rapid, multi-disciplinary analysis of many design variables by a small engineering team. The designer must walk a line between fidelity and productivity, picking tools and methods with the appropriate balance of characteristics to achieve the goals of the study, while staying within the available resources. Identifying geometric details that are important, and those that are not, is critical to making modeling and methodology choices. This is true for both the low-order analysis methods traditionally used in Conceptual design as well as the highest-order analyses available. This paper will highlight some of Conceptual design's characteristics that drive the designer s choices as well as modeling examples for several aircraft configurations using the open source version of the Vehicle Sketch Pad (Open VSP) aircraft Conceptual design geometry modeler.

  18. Launch Pad Flame Trench Refractory Materials

    NASA Technical Reports Server (NTRS)

    Calle, Luz M.; Hintze, Paul E.; Parlier, Christopher R.; Bucherl, Cori; Sampson, Jeffrey W.; Curran, Jerome P.; Kolody, Mark; Perusich, Steve; Whitten, Mary

    2010-01-01

    The launch complexes at NASA's John F. Kennedy Space Center (KSC) are critical support facilities for the successful launch of space-based vehicles. These facilities include a flame trench that bisects the pad at ground level. This trench includes a flame deflector system that consists of an inverted, V-shaped steel structure covered with a high temperature concrete material five inches thick that extends across the center of the flame trench. One side of the "V11 receives and deflects the flames from the orbiter main engines; the opposite side deflects the flames from the solid rocket boosters. There are also two movable deflectors at the top of the trench to provide additional protection to shuttle hardware from the solid rocket booster flames. These facilities are over 40 years old and are experiencing constant deterioration from launch heat/blast effects and environmental exposure. The refractory material currently used in launch pad flame deflectors has become susceptible to failure, resulting in large sections of the material breaking away from the steel base structure and creating high-speed projectiles during launch. These projectiles jeopardize the safety of the launch complex, crew, and vehicle. Post launch inspections have revealed that the number and frequency of repairs, as well as the area and size of the damage, is increasing with the number of launches. The Space Shuttle Program has accepted the extensive ground processing costs for post launch repair of damaged areas and investigations of future launch related failures for the remainder of the program. There currently are no long term solutions available for Constellation Program ground operations to address the poor performance and subsequent failures of the refractory materials. Over the last three years, significant liberation of refractory material in the flame trench and fire bricks along the adjacent trench walls following Space Shuttle launches have resulted in extensive investigations of

  19. Metal pad instabilities in liquid metal batteries.

    PubMed

    Zikanov, Oleg

    2015-12-01

    A mechanical analogy is used to analyze the interaction between the magnetic field, electric current, and deformation of interfaces in liquid metal batteries. In the framework of a low-mode, nondissipative, linear stability model, it is found that, during charging or discharging, a sufficiently large battery is prone to instabilities of two types. One is similar to the metal pad instability known to exist in the aluminum reduction cells. Another type is new. It is related to the destabilizing effect of the Lorentz force formed by the azimuthal magnetic field induced by the base current, and the current perturbations caused by the local variations of the thickness of the electrolyte layer. PMID:26764818

  20. Microneurovascular free digital pad transfer in the dog.

    PubMed

    Basher, A W; Fowler, J D; Bowen, C V; Clark, E G; Crosby, N L

    1990-01-01

    By cadaver dissections, the fifth digit of the canine hind limb was determined to have a consistent neurovascular anatomy, and therefore be a suitable donor for an axial pattern digital pad flap. The defined digital pad flap was transferred to the region of an excised metacarpal pad by microneurovascular anastomoses in five operations on four dogs. One flap failure was considered to result from failure of the venous anastomosis. In all four successful transfers, cutaneous sensation was reestablished on average in 78 days. There was histologic evidence of nerve regeneration across the anastomosis in one dog at week 24. The transferred pads of three dogs monitored for 15 months underwent hypertrophic changes. There were no complications in two active dogs. In one dog, superficial ulceration of a region of the flap adjacent to the pad required surgical revision. This dog continued to show mild lameness after daily runs of 3 to 4 km. PMID:1971973

  1. Pad printer for electronics. Final report

    SciTech Connect

    1998-05-01

    This is the Final report on DARPA-sponsored development Program Pad Printer for Electronics DE-FC04-95AL87486 which was initiated in February, 1995 and intended to run 24 months to February 1997. The Program has significant value to the Thick Film processing industry, an electronic manufacturing alternative for producing functional modules integrated at the multichip level. The result is highly reliable, high volumetric efficiency, subassemblies for military applications and for commercial applications in severe environments, such as automotive, portable communications, and bio-implantable devices. The program progressed quite satisfactorily through 19 months, when it encountered severe, non-technical, difficulties. Resolving these difficulties resulted in several months of delay in completing the Program, but resulted in only a trivial increase in total program cost and no increase in cost to the sponsor. The principle Objective of the Program was the development of a printing system -- machine and appropriate inks -- compatible with existing thick-film processing but offering a 5x improvement in line density. This objective has been met. The Pad Printer is capable of printing suitable inks in traces 25 g wide on 50g centers to a fired thickness of 3 {mu}; each of these parameters is roughly 1/5 the value of the current alternative, silk-screen printing. The available inks represent an assortment of conductor, dielectric, and insulator formulations and the knowledge developed permits extending this family of inks to new and diverse functional materials. An important secondary objective was maximum compatibility with existing Thick Film processing; the printer and ink systems may be substituted directly for the silk screen printers in existing processes. The Program reached or exceeded its other Technical Objectives in almost every case and, in those few instances where the objective was only partially met, work continues under private funding.

  2. iPads in Breast Imaging – A Phantom Study

    PubMed Central

    Hammon, M.; Schlechtweg, P. M.; Schulz-Wendtland, R.; Uder, M.; Schwab, S. A.

    2014-01-01

    Introduction: Modern tablet PCs as the iPad are becoming more and more integrated into medicine. The aim of this study was to evaluate the display quality of iPads regarding digital mammography. Materials and Methods: Three experienced readers compared the display quality of the iPad 2 and 3 with a dedicated 10 megapixel (MP) mammography liquid crystal display (LCD) screen in consensus using the standardized Contrast Detail Mammography (CDMAM) phantom. Phantom fields without agreement between the readers were classified as “uncertain”, correct 2 : 1 decisions were classified as “uncertain/readable”. In a second step display quality of the three reading devices was judged subjectively in a side by side comparison. Results: The 10 MP screen was superior to both iPads in 4 (phantom-)fields and inferior in 2 fields. Comparing the iPads, version 3 was superior in 4 fields and version 2 was superior in 1 field. However these differences were not significant. Total number of “uncertain” fields did not show significant differences. The number of “uncertain” fields was 15 with the 10 MP screen, 16 with the iPad 2 and 17 with the iPad 3 (p > 0.05), the number of “uncertain/readable” fields was 4, 7 and 8, respectively. Subjective image quality of the iPad 3 and the 10 MP screen was rated superior to the iPad 2. Conclusion: The evaluated iPads, especially in version 3, seem to be adequate to display mammograms in a diagnostic quality and thus could be useful e.g. for patient consultation, clinical demonstration or educational and teaching purposes. However primary mammogram reading should still be performed on dedicated large sized reading screens. PMID:24741126

  3. Binocular iPad treatment for amblyopia in preschool children

    PubMed Central

    Birch, Eileen E.; Li, Simone L.; Jost, Reed M.; Morale, Sarah E.; De La Cruz, Angie; Stager, David; Dao, Lori; Stager, David R.

    2014-01-01

    Background Recent experimental evidence supports a role for binocular visual experience in the treatment of amblyopia. The purpose of this study was to determine whether repeated binocular visual experience with dichoptic iPad games could effectively treat amblyopia in preschool children. Methods A total of 50 consecutive amblyopic preschool children 3–6.9 years of age were assigned to play sham iPad games (first 5 children) or binocular iPad games (n = 45) for at least 4 hours per week for 4 weeks. Thirty (67%) children in the binocular iPad group and 4 (80%) in the sham iPad group were also treated with patching at a different time of day. Visual acuity and stereoacuity were assessed at baseline, at 4 weeks, and at 3 months after the cessation of game play. Results The sham iPad group had no significant improvement in visual acuity (t4 = 0.34, P = 0.75). In the binocular iPad group, mean visual acuity (plus or minus standard error) improved from 0.43 ± 0.03 at baseline to 0.34 ± 0.03 logMAR at 4 weeks (n = 45; paired t44 = 4.93; P < 0.0001). Stereoacuity did not significantly improve (t44 = 1.35, P = 0.18). Children who played the binocular iPad games for ≥8 hours (≥50% compliance) had significantly more visual acuity improvement than children who played 0–4 hours (t43 = 4.21, P = 0.0001). Conclusions Repeated binocular experience, provided by dichoptic iPad game play, was more effective than sham iPad game play as a treatment for amblyopia in preschool children. PMID:25727578

  4. [The supinator fat pad in fractures of the elbow joint].

    PubMed

    Schunk, K; Grossholz, M; Schild, H

    1989-03-01

    The position of the supinator fat pad is regarded as a valuable sign in fractures of the elbow. In our patients the pad was visible in 277 out of 337 cases (82%). The sign was positive in only 27 out of 55 proximal fractures of the radius (sensitivity 0.49). There was no correlation between the severity of the fracture and the sign. There was marked variation in the distance between the pad and the radius, depending on age, build and projection. Our results indicate that the sign is not suitable for the diagnosis of fracture of the elbow. PMID:2538879

  5. 48. DETAIL VIEW OF AIR VENT AT 'CATFISH' LAUNCH PAD ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    48. DETAIL VIEW OF AIR VENT AT 'CATFISH' LAUNCH PAD Everett Weinreb, photographer, March 1988 - Mount Gleason Nike Missile Site, Angeles National Forest, South of Soledad Canyon, Sylmar, Los Angeles County, CA

  6. 43. DETAIL VIEW OF 'CATFISH' LAUNCH PAD (continues view of ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    43. DETAIL VIEW OF 'CATFISH' LAUNCH PAD (continues view of CA-57-7) Everett Weinreb, photographer, March 1988 - Mount Gleason Nike Missile Site, Angeles National Forest, South of Soledad Canyon, Sylmar, Los Angeles County, CA

  7. 32. DETAIL VIEW OF CAMERA PIT SOUTH OF LAUNCH PAD ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    32. DETAIL VIEW OF CAMERA PIT SOUTH OF LAUNCH PAD WITH CAMERA AIMED AT LAUNCH DECK; VIEW TO NORTHEAST. - Cape Canaveral Air Station, Launch Complex 17, Facility 28402, East end of Lighthouse Road, Cape Canaveral, Brevard County, FL

  8. 21 CFR 872.3540 - OTC denture cushion or pad.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ...-counter. (b) Classification. (1) Class I if the device is made of wax-impregnated cotton cloth that the... denture cushion or pad is made of a material other than wax-impregnated cotton cloth or if the...

  9. 21 CFR 872.3540 - OTC denture cushion or pad.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ...-counter. (b) Classification. (1) Class I if the device is made of wax-impregnated cotton cloth that the... denture cushion or pad is made of a material other than wax-impregnated cotton cloth or if the...

  10. 21 CFR 872.3540 - OTC denture cushion or pad.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ...-counter. (b) Classification. (1) Class I if the device is made of wax-impregnated cotton cloth that the... denture cushion or pad is made of a material other than wax-impregnated cotton cloth or if the...

  11. 21 CFR 872.3540 - OTC denture cushion or pad.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ...-counter. (b) Classification. (1) Class I if the device is made of wax-impregnated cotton cloth that the... denture cushion or pad is made of a material other than wax-impregnated cotton cloth or if the...

  12. 21 CFR 872.3540 - OTC denture cushion or pad.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ...-counter. (b) Classification. (1) Class I if the device is made of wax-impregnated cotton cloth that the... denture cushion or pad is made of a material other than wax-impregnated cotton cloth or if the...

  13. Preventive medicine oversight of splash pads on military installations.

    PubMed

    Hardcastle, Lisa Raysby; Perry, Matthew; Browne, Ashley

    2015-01-01

    Over the past several years, an increasing number of military installations have installed splash pads that provide fun, recreational water entertainment for Soldiers and their families. The addition of splash pads brings added responsibilities for medical treatment facility preventive medicine oversight and installation facilities maintenance to ensure a safe and healthy environment. Currently, there are no consistent standards or detailed guidance for military installations to follow when installing and maintaining splash pads. The central issues associated with splash pads on military installations are water quality and risk for waterborne illnesses, responsibility for safety and health oversight, and federal energy and water sustainability mandates. This article examines the importance of implementing a standard for design and oversight to ensure the health and safety of Soldiers and their families. PMID:25651143

  14. Overview of the Colorado River Canyon from the helicopter pad. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Overview of the Colorado River Canyon from the helicopter pad. View of the Nevada side where new bridge will cross canyon, view northwest - Hoover Dam, Spanning Colorado River at Route 93, Boulder City, Clark County, NV

  15. Correlations for Saturation Efficiency of Evaporative Cooling Pads

    NASA Astrophysics Data System (ADS)

    Jain, J. K.; Hindoliya, D. A.

    2014-01-01

    This paper presents some experimental investigations to obtain correlations for saturation efficiency of evaporative cooling pads. Two commonly used materials namely aspen and khus fibers along with new materials namely coconut fibers and palash fibers were tested in a laboratory using suitably fabricated test setup. Simple mathematical correlations have been developed for calculating saturation efficiency of evaporating cooling pads which can be used to predict their performance at any desired mass flow rate. Performances of four different pad materials were also compared using developed correlations. An attempt was made to test two new materials (i.e. fibers of palash wood and coconut) to check their suitability as wetted media for evaporative cooling pads. It was found that Palash wood fibers offered highest saturation efficiency compared to that of other existing materials such as aspen and khus fibers at different mass flow rate of air.

  16. 35. Photocopy of Photograph VIEW TO EAST, VIEW OF PAD ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    35. Photocopy of Photograph VIEW TO EAST, VIEW OF PAD B LAUNCH DECK AND UMBILICAL MAST, 28 February 1966. - Cape Canaveral Air Station, Launch Complex 17, Facility 28402, East end of Lighthouse Road, Cape Canaveral, Brevard County, FL

  17. 19. MUELLER FIRE HYDRANT NEAR LAUNCHING PAD IN STATION "0". ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    19. MUELLER FIRE HYDRANT NEAR LAUNCHING PAD IN STATION "0". - Edwards Air Force Base, South Base Sled Track, Edwards Air Force Base, North of Avenue B, between 100th & 140th Streets East, Lancaster, Los Angeles County, CA

  18. 58. Overall view of entry to launch pad from inside ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    58. Overall view of entry to launch pad from inside gate with building 157, sentry control box on right, looking northeast - Nike Missile Battery MS-40, County Road No. 260, Farmington, Dakota County, MN

  19. 56. Overall view towards launch pad with building 157, sentry ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    56. Overall view towards launch pad with building 157, sentry control box on left, and building 156, Warhead Building on right, looking southwest - Nike Missile Battery MS-40, County Road No. 260, Farmington, Dakota County, MN

  20. 16 CFR 1632.5 - Mattress pad test procedure.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. (v) A different number of... substrate. (b) Flame resistant mattress pads. The following additional requirements shall be applicable...

  1. 16 CFR 1632.5 - Mattress pad test procedure.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. (v) A different number of... substrate. (b) Flame resistant mattress pads. The following additional requirements shall be applicable...

  2. 2. CONCRETE PADDING AREA BETWEEN BERM MOUNDS, LOOKING NORTH FROM ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    2. CONCRETE PADDING AREA BETWEEN BERM MOUNDS, LOOKING NORTH FROM TOP OF BERM. - NIKE Missile Base C-84, Acid Fueling Station, North of Launch Area Entrance Drive, eastern central portion of base, Barrington, Cook County, IL

  3. 8. View east. East abutment, showing bearings on concrete pads, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    8. View east. East abutment, showing bearings on concrete pads, drainage pipes for approach, and scupper downspouts. - Walpole-Westminster Bridge, Spanning Connecticut River between Walpole, NH & Westminster, VT, Walpole, Cheshire County, NH

  4. 7. Shed and keeper' house with helicopter pad in foreground, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    7. Shed and keeper' house with helicopter pad in foreground, view east, southwest and northwest sides - Goat Island Light Station, Goat Island, next to entrance to Cape Porpoise Harbor, just south of Trott Island, Cape Porpoise, York County, ME

  5. Orbital Rolls to Launch Pad at Wallops for Station Flight

    NASA Video Gallery

    An Orbital Sciences Corporation Antares rolled out to launch Pad-0A at NASA's Wallops Flight Facility, Sunday, January 5, 2014, in advance of a planned Wednesday, Jan. 8th, 1:32 p.m. EST launch. Th...

  6. 16. CONCRETE PAD ON WHICH AN ELECTRICAL REACTOR WAS MOUNTED, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    16. CONCRETE PAD ON WHICH AN ELECTRICAL REACTOR WAS MOUNTED, IN THE BASEMENT, EAST WALL - Bonneville Power Administration South Bank Substation, I-84, South of Bonneville Dam Powerhouse, Bonneville, Multnomah County, OR

  7. Time-Lapse: Mobile Launcher Moves to Launch Pad

    NASA Video Gallery

    The mobile launcher that will host NASA's Space Launch System and new Orion spacecraft was moved to Launch Pad 39B at NASA's Kennedy Space Center in Florida to begin two weeks of structural and sys...

  8. 4. VIEW SOUTHEAST, COMPRESSOR PADS Imperial Carbon Black Plant ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. VIEW SOUTHEAST, COMPRESSOR PADS - Imperial Carbon Black Plant (Ruin), North side of North Fork of Hughes River along Bunnell Run Road just over 0.5 mile from its intersection with State Route 16, Harrisville, Ritchie County, WV

  9. 2. VIEW SOUTHWEST, COMPRESSOR PADS Imperial Carbon Black Plant ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    2. VIEW SOUTHWEST, COMPRESSOR PADS - Imperial Carbon Black Plant (Ruin), North side of North Fork of Hughes River along Bunnell Run Road just over 0.5 mile from its intersection with State Route 16, Harrisville, Ritchie County, WV

  10. Behind the Scenes: Shuttle Crawls to Launch Pad

    NASA Video Gallery

    In this episode of NASA Behind the Scenes, take a look at what's needed to roll a space shuttle out of the Vehicle Assembly Building and out to the launch pad. Astronaut Mike Massimino talks to som...

  11. Method for Producing Launch/Landing Pads and Structures Project

    NASA Technical Reports Server (NTRS)

    Mueller, Robert P. (Compiler)

    2015-01-01

    Current plans for deep space exploration include building landing-launch pads capable of withstanding the rocket blast of much larger spacecraft that that of the Apollo days. The proposed concept will develop lightweight launch and landing pad materials from in-situ materials, utilizing regolith to produce controllable porous cast metallic foam brickstiles shapes. These shapes can be utilized to lay a landing launch platform, as a construction material or as more complex parts of mechanical assemblies.

  12. Assessment of Raman Spectroscopy as a Silicone Pad Production Diagnostic

    SciTech Connect

    Saab, A P; Balazs, G B; Maxwell, R S

    2005-05-05

    Silicone pressure pads are currently deployed in the W80. The mechanical properties of these pads are largely based on the degree of crosslinking between the polymer components that comprise the raw gumstock from which they are formed. Therefore, it is desirable for purposes of both production and systematic study of these materials to have a rapid, reliable means of assaying the extent of crosslinking. The present report describes the evaluation of Raman spectroscopy in this capacity.

  13. 44. VIEW OF UMBILICAL MAST AND LAUNCH PAD FROM SOUTHWEST. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    44. VIEW OF UMBILICAL MAST AND LAUNCH PAD FROM SOUTHWEST. DOORS FOR THE UMBILICAL MAST TRENCH RAISED FOR MAINTENANCE POSITION OF 10 DEGREES. LAUNCHER IS RIGHT OF MAST; RAILS PARALLEL TO MAST. CONTROL PANELS LEFT TO RIGHT: ELECTRICAL PANEL, COMMUNICATIONS PANEL, AND MAST CONTROL PANEL. - Vandenberg Air Force Base, Space Launch Complex 3, Launch Pad 3 East, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

  14. Demonstrating Optical Activity Using an iPad

    ERIC Educational Resources Information Center

    Schwartz, Pauline M.; Lepore, Dante M.; Morneau, Brandy N.; Barratt, Carl

    2011-01-01

    Optical activity using an iPad as a source of polarized light is demonstrated. A sample crystal or solution can be placed on the iPad running a white screen app. The sample is viewed through a polarized filter that can be rotated. This setup can be used in the laboratory or with a document camera to easily project in a large lecture hall.…

  15. Riverland ERA maintenance pad site diesel contamination risk assessment

    SciTech Connect

    Valcich, P.J.

    1993-12-02

    The maintenance pad site consists of a concrete pad and underlying soils, approximately 15 by 46 m in area, and a drainage ditch with dimensions of 2.4 by 91 m. The ditch is located approximately 60 m from the concrete pad and is oriented parallel to the pads long axis. The facility was built in 1943, at which time the concrete pad was the floor of a maintenance shed for railroad activities. In 1955, use of the facility as a maintenance shed was discontinued. Between 1955 and 1957, the facility was used as a radioactivity decontamination area for railroad cars; acetone-soaked rags were used to remove surface contamination from the cars. The concrete pad was washed down with a mixture of water and diesel fuel, which was then flushed via clay pipe to the drainage ditch. In 1963, the maintenance shed was torn down and the concrete pad covered with approximately one-half meter of fill. The concrete pad was re-exposed in 1993. The site was sampled for Toxicity Characteristic Leachate Procedure (TCLP) metals, volatile, and semi-volatile compounds, as well as for extractable fuel hydrocarbons. A total of 17 samples were collected from surface concrete, soil beneath surface concrete, and ditch soil. One concrete sample and one ditch soil sample were split. The ditch soil sample was also duplicated. The relative percent difference (RPD) in extractable hydrocarbons of the two split samples, one from concrete and one from ditch soil are, respectively, 52% and 186%. The RPD for the duplicate sample, taken from the same ditch soil sample from which one of the splits was taken, is 39%.

  16. 21 CFR 884.5425 - Scented or scented deodorized menstrual pad.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Scented or scented deodorized menstrual pad. 884... Therapeutic Devices § 884.5425 Scented or scented deodorized menstrual pad. (a) Identification. A scented or scented deodorized menstrual pad is a device that is a pad made of cellulosic or synthetic material...

  17. The CIMSS iPad Library and ESIP Teacher Workshops

    NASA Astrophysics Data System (ADS)

    Dahlman, L.; Mooney, M. E.

    2012-12-01

    The Cooperative Institute for Meteorological Satellite Studies (CIMSS) at the University of Wisconsin-Madison launched a new initiative in 2012 to engage teachers and students in data acquisition and regional climate studies. The CIMSS iPad Library, part of a NASA funded Climate Literacy Ambassadors project, loans iPads to science teachers for an entire school year. The first units were distributed at a NOAA funded teacher workshop conducted at the annual Earth Science Information Partners (ESIP) summer conference. Educators learned about numerous NOAA and NASA resources at the ESIP Teacher Workshop and also several different climate-related Apps, including SatCam, an application for iOS devices that allows users to collect observations of local cloud and surface conditions coordinated with an overpass of the Terra, Aqua, or Suomi NPP satellite. This presentation will outline connections between the Climate Literacy Ambassadors community and ESIP Teacher Workshops before delving into details about the new iPad Library and SatCam. We will discuss considerations and challenges related to a technology loaning library, software recoding to HTML5, and some advantages and limitations related to iPads. We will also share feedback acquired over the fall from ESIP Educators using the SatCam App with their students with the iPads they borrowed (like books) from the CIMSS iPad Library.

  18. Saturn I (SA-1) on Launch Pad

    NASA Technical Reports Server (NTRS)

    1961-01-01

    On October 27, 1961, the Marshall Space Flight Center and the Nation marked a high point in the 3-year-old Saturn development program when the first Saturn vehicle, SA-1, flew a flawless 215-mile ballistic trajectory from Cape Canaveral, Florida. SA-1 is pictured here on the launch pad ready for lift off. Developed at the Marshall Space Flight Center (MSFC) under the direction of Dr. Wernher von Braun, SA-1 incorporated a Saturn I, Block I engine. The typical height of a Block I vehicle was approximately 163 feet and had only one live stage. It consisted of eight tanks, each 70 inches in diameter, clustered around a central tank, 105 inches in diameter. Four of the external tanks were fuel tanks for the RP-1 (kerosene) fuel. The other four, spaced alternately with the fuel tanks, were liquid oxygen tanks, as was the large center tank. All fuel tanks and liquid oxygen tanks drained at the same rates respectively. The thrust for the stage came from eight H-1 engines, each producing a thrust of 165,000 pounds, for a total thrust of over 1,300,000 pounds. The engines were arranged in a double pattern. Four engines, located inboard, were fixed in a square pattern around the stage axis and canted outward slightly, while the remaining four engines were located outboard in a larger square pattern offset 40 degrees from the inner pattern. Unlike the inner engines, each outer engine was gimbaled. That is, each could be swung through an arc. They were gimbaled as a means of steering the rocket, by letting the instrumentation of the rocket correct any deviations of its powered trajectory. The block I required engine gimabling as the only method of guiding and stabilizing the rocket through the lower atmosphere. The upper stages of the Block I rocket reflected the three-stage configuration of the Saturn I vehicle.

  19. Aircraft Conceptual Design Using Vehicle Sketch Pad

    NASA Technical Reports Server (NTRS)

    Fredericks, William J.; Antcliff, Kevin R.; Costa, Guillermo; Deshpande, Nachiket; Moore, Mark D.; Miguel, Edric A. San; Snyder, Alison N.

    2010-01-01

    Vehicle Sketch Pad (VSP) is a parametric geometry modeling tool that is intended for use in the conceptual design of aircraft. The intent of this software is to rapidly model aircraft configurations without expending the expertise and time that is typically required for modeling with traditional Computer Aided Design (CAD) packages. VSP accomplishes this by using parametrically defined components, such as a wing that is defined by span, area, sweep, taper ratio, thickness to cord, and so on. During this phase of frequent design builds, changes to the model can be rapidly visualized along with the internal volumetric layout. Using this geometry-based approach, parameters such as wetted areas and cord lengths can be easily extracted for rapid external performance analyses, such as a parasite drag buildup. At the completion of the conceptual design phase, VSP can export its geometry to higher fidelity tools. This geometry tool was developed by NASA and is freely available to U.S. companies and universities. It has become integral to conceptual design in the Aeronautics Systems Analysis Branch (ASAB) here at NASA Langley Research Center and is currently being used at over 100 universities, aerospace companies, and other government agencies. This paper focuses on the use of VSP in recent NASA conceptual design studies to facilitate geometry-centered design methodology. Such a process is shown to promote greater levels of creativity, more rapid assessment of critical design issues, and improved ability to quickly interact with higher order analyses. A number of VSP vehicle model examples are compared to CAD-based conceptual design, from a designer perspective; comparisons are also made of the time and expertise required to build the geometry representations as well.

  20. The effect of football shoulder pads on pulmonary function.

    PubMed

    Coast, J Richard; Baronas, Jessica L; Morris, Colleen; Willeford, K Sean

    2005-12-01

    Restriction of expansion of the lungs or chest wall impedes inflation of the lungs during inhalation. Functional changes occurring during such restriction include reduced pulmonary and/or chest wall compliance, decreases in pulmonary function, and ultimately a decrease in exercise performance. Such restriction can be seen in several pathologic conditions such as scoliosis or obesity, as well as occupational situations such as the wearing of bullet-proof vests. This study investigated the hypothesis that tightened football shoulder pads produce decrements in pulmonary function similar to those shown in previous studies involving other external chest-wall restricting devices. In this study, 24 subjects, all members of a collegiate division IAA football team and used to wearing the pads, performed standard pulmonary function tests while wearing no pads (control, CTRL), wearing pads that were not secured (pads loose, PL) and while wearing pads secured "game-tight" (pads tight, PT). The data showed that both forced vital capacity (FVC) and forced expiratory volume in one second (FEV1.0) were significantly decreased in the PT condition compared to either the CTRL or PL condition, with no changes in the FEV1.0/FVC ratio or peak expiratory flow rate. These results are consistent with a restrictive condition and support our hypothesis that tightened shoulder pads reduce pulmonary function. Further studies remain to be performed to determine whether these changes lead to decreased exercise performance and whether equipment modifications can be made to limit alterations in pulmonary function without decreasing the protective value of the pads. Key PointsThe shoulder pads used in American football extend to the xyphoid process and may provide a restriction to breathing. This was tested in the present study in 24 college-level football players with normal resting pulmonary function.The results showed that there was a decrease in FVC of approximately 150 ml and a similar

  1. Inhibition of PAD4 activity is sufficient to disrupt mouse and human NET formation

    PubMed Central

    Lewis, Huw D.; Liddle, John; Coote, Jim E.; Atkinson, Stephen J.; Barker, Michael D.; Bax, Benjamin, D.; Bicker, Kevin L.; Bingham, Ryan P.; Campbell, Matthew; Chen, Yu Hua; Chung, Chun-wa; Craggs, Peter D.; Davis, Rob P.; Eberhard, Dirk; Joberty, Gerard; Lind, Kenneth E.; Locke, Kelly; Maller, Claire; Martinod, Kimberly; Patten, Chris; Polyakova, Oxana; Rise, Cecil E.; Rüdiger, Martin; Sheppard, Robert J.; Slade, Daniel J.; Thomas, Pamela; Thorpe, Jim; Yao, Gang; Drewes, Gerard; Wagner, Denisa D.; Thompson, Paul R.; Prinjha, Rab K.; Wilson, David M.

    2015-01-01

    PAD4 has been strongly implicated in the pathogenesis of autoimmune, cardiovascular and oncological diseases, through clinical genetics and gene disruption in mice. Novel, selective PAD4 inhibitors binding to a calcium-deficient form of the PAD4 enzyme have, for the first time, validated the critical enzymatic role of human and mouse PAD4 in both histone citrullination and neutrophil extracellular trap formation. The therapeutic potential of PAD4 inhibitors can now be explored. PMID:25622091

  2. STS-101 Atlantis near Launch Pad 39-A

    NASA Technical Reports Server (NTRS)

    2000-01-01

    Seen from across the backwaters of the Indian River Lagoon, the Space Shuttle Atlantis, atop the mobile launcher platform and crawler-transporter, nears Launch Pad 39A at 1 mph. The crawler- transporter takes about five hours to cover the 3.4 miles from the Vehicle Assembly Building to the launch pad. The crawler- transporter carries its cargo at 1 mph, taking about five hours to cover the 3.4 miles from the Vehicle Assembly Building to the launch pad. A leveling system on the crawler-transporter keeps the top of the Space Shuttle vertical, especially negotiating the ramp leading to the launch pads and when it is raised and lowered on pedestals at the pad. Liftoff of Atlantis on mission STS-101 is scheduled for April 17 at 7:03 p.m. EDT. STS-101 is a logistics and resupply mission for the International Space Station, to restore full redundancy to the International Space Station power system in preparation for the arrival of the next pressurized module, the Russian-built Zvezda.

  3. Insect tricks: two-phasic foot pad secretion prevents slipping.

    PubMed

    Dirks, Jan-Henning; Clemente, Christofer J; Federle, Walter

    2010-04-01

    Many insects cling to vertical and inverted surfaces with pads that adhere by nanometre-thin films of liquid secretion. This fluid is an emulsion, consisting of watery droplets in an oily continuous phase. The detailed function of its two-phasic nature has remained unclear. Here we show that the pad emulsion provides a mechanism that prevents insects from slipping on smooth substrates. We discovered that it is possible to manipulate the adhesive secretion in vivo using smooth polyimide substrates that selectively absorb its watery component. While thick layers of polyimide spin-coated onto glass removed all visible hydrophilic droplets, thin coatings left the emulsion in its typical form. Force measurements of stick insect pads sliding on these substrates demonstrated that the reduction of the watery phase resulted in a significant decrease in friction forces. Artificial control pads made of polydimethylsiloxane showed no difference when tested on the same substrates, confirming that the effect is caused by the insects' fluid-based adhesive system. Our findings suggest that insect adhesive pads use emulsions with non-Newtonian properties, which may have been optimized by natural selection. Emulsions as adhesive secretions combine the benefits of 'wet' adhesion and resistance against shear forces. PMID:19755498

  4. Visible light active photocatalyst from recycled disposable heating pads

    NASA Astrophysics Data System (ADS)

    Lee, Meng-Chien; Wang, Chun-Yu; Chen, Che-Chin; Wang, Chih-Ming; Hsiao, Ta-Chih; Tsai, Din Ping

    2016-01-01

    Alpha-Fe2O3 (α-Fe2O3) is cheap and abundant and has potential to be a highly efficient photocatalyst for water splitting. According to the report, there are a huge amount of disposable heating pads being created every year, and the pads are used one time then thrown away. We found that the main product of used heating pads is α-Fe2O3. Here, we collect and purify the α-Fe2O3 powder in the used heating pads using low power consumption processes. It is shown that the recycled heating pads can be used as a cost-effective photocatalyst for H2 energy and for decomposition of organic pollutants as well. Additionally, the plasmonic enhanced photocatalysis reaction of α-Fe2O3 is also investigated. It is found that H2 evolution rate can be enhanced 15% using α-Fe2O3 nanoparticles coated with a thin Au layer. The degradation of methylene blue can also enhance 12% compared to photocatalyst α-Fe2O3 nanoparticles coated without Au layer.

  5. Gecko inspired carbon nanotube based thermal gap pads

    NASA Astrophysics Data System (ADS)

    Sethi, Sunny; Dhinojwala, Ali

    2012-02-01

    Thermal management has become a critical factor in designing the next generation of microprocessors. The bottleneck in design of material for efficient heat transfer from electronic units to heat sinks is to enhance heat flow across interface between two dissimilar, rough surfaces. Carbon nanotubes (CNT) have been shown to be promising candidates for thermal transport. However, the heat transport across the interface continues to be a challenging hurdle. In the current work we designed free standing thermal pads based on gecko-inspired carbon nanotube adhesives. The pads were made of metallic carbon nanotubes and the structure was designed such that it would allow large area of intimate contact. We showed that these adhesive pads can be used as electrical and thermal interconnects.

  6. Closing microvascular lesions with fibrin sealant-attached muscle pads.

    PubMed

    Fehm, Nando Percy; Vatankhah, Bijan; Dittmar, Michael S; Tevetoglu, Yesim; Retzl, Gerald; Horn, Markus

    2005-01-01

    Fibrin sealants are used in a variety of surgical procedures, mainly for purposes of hemostasis and assisted wound healing. The combined use of fibrin sealant and autologous muscle pads for hemostasis was not reported previously. Arterial incisions in the common carotid artery in rats were closed by the combined application of fibrin sealant and an autologous muscle pad. Postsurgical vessel patency and degree of stenosis were evaluated by color duplex sonography, computed tomography angiography, and postmortem histology. The combined application of muscle pad and fibrin sealant and achievement of hemostasis was feasible in all animals. Seventy-eight percent of animals showed no or only slight postsurgical vessel stenosis. Our method is simple and quick to perform, showing a high potential for hemostasis in microvascular lesions. Therefore, it might be used in future experimental studies for conservation of vessel patency after arterial catheterization and in experimental or clinical vascular surgery. PMID:16184526

  7. On pads and filters: Processing strong-motion data

    USGS Publications Warehouse

    Boore, D.M.

    2005-01-01

    Processing of strong-motion data in many cases can be as straightforward as filtering the acceleration time series and integrating to obtain velocity and displacement. To avoid the introduction of spurious low-frequency noise in quantities derived from the filtered accelerations, however, care must be taken to append zero pads of adequate length to the beginning and end of the segment of recorded data. These padded sections of the filtered acceleration need to be retained when deriving velocities, displacements, Fourier spectra, and response spectra. In addition, these padded and filtered sections should also be included in the time series used in the dynamic analysis of structures and soils to ensure compatibility with the filtered accelerations.

  8. STS-112 Atlantis rollout to Launch Pad 39-B

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- After an early morning rollout, Space Shuttle Atlantis sits on the launch pad. Visible near the tail are the tail service masts that support the fluid, gas and electrical requirements of the orbiter's liquid oxygen and liquid hydrogen aft T-0 umbilicals. After being stacked with its solid rocket boosters and external tank, Atlantis began its rollout to Launch Pad 39B at 2:27 a.m. EDT in preparation for launch to the International Space Station. The Shuttle arrived at the Pad and was hard down at 9:38 a.m. Launch is scheduled no earlier than Oct. 2 for mission STS-112, the 15th assembly flight to the International Space Station. Atlantis will carry the S1 Integrated Truss Structure, which will be attached to the central truss segment, the S0 truss, during the mission.

  9. STS-112 Atlantis rollout to Launch Pad 39-B

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- After an early morning rollout, Space Shuttle Atlantis nears the top of the launch pad. The Rotating Service Structure is wide open (in front of the Mobile Launcher Platform). After being stacked with its solid rocket boosters and external tank, Atlantis began its rollout to Launch Pad 39B at 2:27 a.m. EDT in preparation for launch to the International Space Station. The Shuttle arrived at the Pad and was hard down at 9:38 a.m. Launch is scheduled no earlier than Oct. 2 for mission STS-112, the 15th assembly flight to the International Space Station. Atlantis will carry the S1 Integrated Truss Structure, which will be attached to the central truss segment, the S0 truss, during the mission.

  10. STS-112 Atlantis rollout to Launch Pad 39-B

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- In the early morning hours, Space Shuttle Atlantis, with its solid rocket boosters and orange external tank, sits atop the Mobile Launcher Platform ready to roll to the launch pad. Atlantis began its rollout to Launch Pad 39B at 2:27 a.m. EDT in preparation for launch to the International Space Station. The Shuttle arrived at the Pad and was hard down at 9:38 a.m. Launch is scheduled no earlier than Oct. 2 for mission STS-112, the 15th assembly flight to the International Space Station. Atlantis will carry the S1 Integrated Truss Structure, which will be attached to the central truss segment, the S0 truss, during the mission.

  11. STS-112 Atlantis rollout to Launch Pad 39-B

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- After an early morning rollout, Space Shuttle Atlantis, atop the Mobile Launcher Platform, passes by the American flag as it moves through the gate at the launch pad. After being stacked with its solid rocket boosters and external tank, Atlantis began its rollout to Launch Pad 39B at 2:27 a.m. EDT in preparation for launch to the International Space Station. The Shuttle arrived at the Pad and was hard down at 9:38 a.m. Launch is scheduled no earlier than Oct. 2 for mission STS-112, the 15th assembly flight to the International Space Station. Atlantis will carry the S1 Integrated Truss Structure, which will be attached to the central truss segment, the S0 truss, during the mission.

  12. STS-112 Atlantis rollout to Launch Pad 39-B

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- After an early morning rollout, Space Shuttle Atlantis sits on the launch pad. The Rotating Service Structure is wide open (at left). After being stacked with its solid rocket boosters and external tank, Atlantis began its rollout to Launch Pad 39B at 2:27 a.m. EDT in preparation for launch to the International Space Station. The Shuttle arrived at the Pad and was hard down at 9:38 a.m. Launch is scheduled no earlier than Oct. 2 for mission STS-112, the 15th assembly flight to the International Space Station. Atlantis will carry the S1 Integrated Truss Structure, which will be attached to the central truss segment, the S0 truss, during the mission.

  13. STS-112 Atlantis rollout to Launch Pad 39-B

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- In the early light of dawn, Atlantis heads to the launch pad, lighted in the distance. After being stacked with its solid rocket boosters and external tank, Atlantis began its rollout to Launch Pad 39B at 2:27 a.m. EDT in preparation for launch to the International Space Station. The Shuttle arrived at the Pad and was hard down at 9:38 a.m. Launch is scheduled no earlier than Oct. 2 for mission STS-112, the 15th assembly flight to the International Space Station. Atlantis will carry the S1 Integrated Truss Structure, which will be attached to the central truss segment, the S0 truss, during the mission.

  14. STS-100 crew members practice emergency escape from the pad

    NASA Technical Reports Server (NTRS)

    2001-01-01

    KENNEDY SPACE CENTER, Fla. - As part of emergency escape training at Launch Pad 39A, the STS-100 crew climb into slidewire baskets that, during a real emergency, would propel them off the Fixed Service Structure to a landing area away from the pad. The crew is taking part in Terminal Countdown Demonstration Test activities that also include a simulated launch countdown. The mission is carrying the Multi-Purpose Logistics Module Raffaello and the SSRMS, to the International Space Station. Raffaello carries six system racks and two storage racks for the U.S. Lab. The SSRMS is crucial to the continued assembly of the orbiting complex. Launch of mission STS-100 is scheduled for April 19 at 2:41 p.m. EDT from Launch Pad 39A.

  15. STS-100 crew members practice emergency escape from the pad

    NASA Technical Reports Server (NTRS)

    2001-01-01

    KENNEDY SPACE CENTER, Fla. - During emergency escape training at Launch Pad 39A, STS-100 Pilot Jeffrey S. Ashby (left) and Commander Kent V. Rominger are in their slidewire basket that, during a real emergency, would propel them off the Fixed Service Structure to a landing area away from the pad. The crew is taking part in Terminal Countdown Demonstration Test activities that also include a simulated launch countdown. The mission is carrying the Multi-Purpose Logistics Module Raffaello and the SSRMS, to the International Space Station. Raffaello carries six system racks and two storage racks for the U.S. Lab. The SSRMS is crucial to the continued assembly of the orbiting complex. Launch of mission STS-100 is scheduled for April 19 at 2:41 p.m. EDT from Launch Pad 39A.

  16. An approach to evaluate capacitance, capacitive reactance and resistance of pivoted pads of a thrust bearing

    NASA Astrophysics Data System (ADS)

    Prashad, Har

    1992-07-01

    A theoretical approach is developed for determining the capacitance and active resistance between the interacting surfaces of pivoted pads and thrust collar, under different conditions of operation. It is shown that resistance and capacitive reactance of a thrust bearing decrease with the number of pads times the values of these parameters for an individual pad, and that capacitance increases with the number of pads times the capacitance of an individual pad. The analysis presented has a potential to diagnose the behavior of pivoted pad thrust bearings with the angle of tilt and the ratio of film thickness at the leading to trailing edge, by determining the variation of capacitance, resistance, and capacitive reactance.

  17. Woodpecker Preventative measures at Launch Pad 39B

    NASA Technical Reports Server (NTRS)

    1995-01-01

    Technicians at Launch Pad 39B take steps to prevent further damage from woodpeckers to the Space Shuttle Discovery, set to lift off July 13 on Mission STS-70. Installing balloons with scary eyes, such as these two near the external tank, are just one of the measures being taken to keep woodpeckers away since Discovery's second rollout to Pad B. Discovery had to be rolled back once to the Vehicle Assembly Building to repair woodpecker holes made in the insulation covering the external tank.

  18. Discrete integrable systems generated by Hermite-Padé approximants

    NASA Astrophysics Data System (ADS)

    Aptekarev, Alexander I.; Derevyagin, Maxim; Van Assche, Walter

    2016-05-01

    We consider Hermite-Padé approximants in the framework of discrete integrable systems defined on the lattice {{{Z}}2} . We show that the concept of multiple orthogonality is intimately related to the Lax representations for the entries of the nearest neighbor recurrence relations and it thus gives rise to a discrete integrable system. We show that the converse statement is also true. More precisely, given the discrete integrable system in question there exists a perfect system of two functions, i.e. a system for which the entire table of Hermite-Padé approximants exists. In addition, we give a few algorithms to find solutions of the discrete system.

  19. Allergic contact dermatitis to acrylates in disposable blue diathermy pads.

    PubMed Central

    Sidhu, S. K.; Shaw, S.

    1999-01-01

    We report 2 cases of elicitation of allergic contact dermatitis to acrylates from disposable blue diathermy pads used on patients who underwent routine surgery. Their reactions were severe, and took approximately 5 weeks to resolve. Both patients gave a prior history of finger tip dermatitis following the use of artificial sculptured acrylic nails, which is a common, but poorly reported, cause of acrylate allergy. Patch testing subsequently confirmed allergies to multiple acrylates present in both the conducting gel of disposable blue diathermy pads, and artificial sculptured acrylic nails. We advocate careful history taking prior to surgery to avoid unnecessary exposure to acrylates in patients already sensitized. Images Figure 1 Figure 2 PMID:10364952

  20. Compression Pad Cavity Heating Augmentation on Orion Heat Shield

    NASA Technical Reports Server (NTRS)

    Hollis, Brian R.

    2011-01-01

    An experimental study has been conducted to assess the effects of compression pad cavities on the aeroheating environment of the Project Orion Crew Exploration Vehicle heat shield. Testing was conducted in Mach 6 and 10 perfect-gas wind tunnels to obtain heating measurements in and around the compression pads cavities using global phosphor thermography. Data were obtained over a wide range of Reynolds numbers that produced laminar, transitional, and turbulent flow within and downstream of the cavities. The effects of cavity dimensions on boundary-layer transition and heating augmentation levels were studied. Correlations were developed for transition onset and for the average cavity-heating augmentation.

  1. The STS-98 crew practices emergency egress from the pad

    NASA Technical Reports Server (NTRS)

    2001-01-01

    KENNEDY SPACE CENTER, Fla. -- During emergency egress training at the Launch Pad, Commander Ken Cockrell gets help adjusting his helmet. The crew is practicing using the slidewire baskets that slide along 1200-foot wire to the landing zone below and nearby bunker. The crew has been taking part in Terminal Countdown Demonstration Test activities, which include the simulated countdown and emergency egress training at the pad. STS-98 is the seventh construction flight to the International Space Station, carrying as payload the U.S. Lab Destiny, a key element in the construction of the ISS. Launch of STS-98 is scheduled for Jan. 19 at 2:11 a.m. EST.

  2. Environmental effects and characterization of the Egyptian radioactive well logging calibration pad facility.

    PubMed

    Al Alfy, Ibrahim Mohammad

    2013-12-01

    A set of ten radioactive well-logging calibration pads were constructed in one of the premises of the Nuclear Materials Authority (NMA), Egypt, at 6th October city. These pads were built for calibrating geophysical well-logging instruments. This calibration facility was conducted through technical assistance and practical support of the International Atomic Energy Agency (IAEA) and (ARCN). There are five uranium pads with three different uranium concentrations and borehole diameters. The other five calibration pads include one from each of the following: blank, potassium, thorium, multi layers and mixed. More than 22 t of various selected Egyptian raw materials were gathered for pad construction from different locations in Egypt. Pad's site and the surrounding area were spectrometrically surveyed before excavation for the construction process of pad-basin floor. They yielded negligible radiation values which are very near to the detected general background. After pad's construction, spectrometric measurements were carried out again in the same locations when the exposed bore holes of the pads were closed. No radioactivity leakage was noticed from the pads. Meanwhile, dose rate values were found to range from 0.12 to 1.26 mS/y. They were measured during the opening of bore holes of the pads. These values depend mainly upon the type and concentration of the pads as well as their borehole diameters. The results of radiospectrometric survey illustrate that the specification of top layers of the pads were constructed according to international standards. PMID:24140880

  3. 21 CFR 890.5740 - Powered heating pad.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Powered heating pad. 890.5740 Section 890.5740 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Therapeutic Devices § 890.5740 Powered...

  4. 21 CFR 890.5740 - Powered heating pad.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Powered heating pad. 890.5740 Section 890.5740 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Therapeutic Devices § 890.5740 Powered...

  5. 21 CFR 890.5740 - Powered heating pad.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Powered heating pad. 890.5740 Section 890.5740 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Therapeutic Devices § 890.5740 Powered...

  6. 21 CFR 890.5740 - Powered heating pad.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Powered heating pad. 890.5740 Section 890.5740 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Therapeutic Devices § 890.5740 Powered...

  7. 13. WALKWAY FROM LAUNCHING PAD TO CABLE TUNNEL STAIRWELL, ALSO ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    13. WALKWAY FROM LAUNCHING PAD TO CABLE TUNNEL STAIRWELL, ALSO SHOWING A PROTECTIVE BERM AT TOP LEFT, AND FIRING CONTROL BLOCKHOUSE 0545 AT TOP RIGHT. - Edwards Air Force Base, South Base Sled Track, Firing Control Blockhouse, South of Sled Track at east end, Lancaster, Los Angeles County, CA

  8. 21 CFR 890.5740 - Powered heating pad.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Powered heating pad. 890.5740 Section 890.5740 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Therapeutic Devices § 890.5740 Powered...

  9. Mobile Perspectives: On iPads--Why Mobile?

    ERIC Educational Resources Information Center

    Gawelek, Mary Ann; Spataro, Mary; Komarny, Phil

    2011-01-01

    Along with their students, faculty have become co-learners and pioneers in the classroom. With no models to work from, they have had to explore, practice, and discover the iPad's potential for expanding learning. Given the recent and rapidly growing access to a dazzling array of intellectual technologies, faculty and staff at Seton Hill, a liberal…

  10. International Perspectives on Literacy Learning with iPads

    ERIC Educational Resources Information Center

    Gallagher, Tiffany L.; Fisher, Douglas; Lapp, Diane; Rowsell, Jennifer; Simpson, Alyson; Scott, Ruth McQuirter; Walsh, Maureen; Ciampa, Katia; Saudelli, Mary Gene

    2015-01-01

    This article profiles the use of the iPad in classroom literacy activities in three instructional environments: Toronto, Canada; San Diego, United States; and Sydney, Australia. The two-year, qualitative study included observational fieldwork filming students' interactions with tablets in the midst of literacy events. Students in each context used…

  11. Silicon nanoparticle-functionalized fiberglass pads for sampling

    SciTech Connect

    Mantey, Kevin; Nayfeh, Munir H.; Al-Hreish, Bahjat; Boparai, Jack; Kumar, Ashok; Stephenson, Larry D.; Nelson, Andrew J.; Alrokayan, Salman A.; Abu-Salah, Khalid M.

    2011-03-15

    We used wet treatment to immobilize luminescent silicon nanoparticles on industrial glass fibers to impart optical and chemical functions to the fiber. Carpets or pads consisting of thousands of fibers are processed in parallel, enhancing the sensitivity of detection and the sampled volume. Treated pads exhibit strong luminescence, characteristic of the luminescence of the particles; showing no shift, broadening, or reduction of quantum efficiency. We demonstrate that drawing material by the pad due to physical adsorption can be reversed. We also demonstrate that allylamine can be covalently attached by photoinduced irradiation reactions, which results in imprinting the amine emission spectrum, providing spectral recognition. The imprint accompanied with a blue-shifting of the luminescence spectrum of the probe, allowing examination of the effect of termination on the nanoparticle structure. The shift is found to be consistent with an increase in the bandgap of the Si nanoparticle and is consistent with Quantum Monte Carlo calculations. In addition to sampling, the nano probe pad has the potential to enable a variety of biomedical applications through subsequent attachment.

  12. STS-102 Discovery lifts off from Launch Pad 39-B

    NASA Technical Reports Server (NTRS)

    2001-01-01

    KENNEDY SPACE CENTER, Fla. - Space Shuttle Discovery rivals the rising sun as it blasts off from Launch Pad 39B at dawn on mission STS-102. . Liftoff occurred at 6:42:09 EST for this eighth flight to the International Space Station.

  13. STS-102 Discovery lifts off from Launch Pad 39-B

    NASA Technical Reports Server (NTRS)

    2001-01-01

    KENNEDY SPACE CENTER, Fla. - As Space Shuttle Atlantis clears Launch Pad 39B, the sun peers over the horizon of the Atlantic Ocean. . Liftoff of Discovery on mission STS-102 occurred at 6:42:09 EST for the eighth flight to the International Space Station.

  14. The pad readout electronics of the SLD Warm Iron Calorimeter

    SciTech Connect

    Burrows, P.N.; Busza, W.; Cartwright, S.L.; Friedman, J.I.; Fuess, S.; Gonzalez, S.; Hansl-Kozanecka, T.; Kendall, H.W.; Lath, A.; Lyons, T.; Osborne, L.S.; Rosenson, L.; Schneekloth, U.; Taylor, F.E.; Verdier, R.; Wadsworth, B.; Williams, D.C.; Yamartino, J.M. ); Byers, B.L.; Escalera, J.; Gioumousis, A.; Gray, R.; Horelick, D.; Kharakh, D.; Messner, R.L.; Moss, J.; Zdark

    1990-08-01

    The design of the pad readout electronics of the Warm Iron Calorimeter for the SLD detector at SLAC, consisting of about 9000 analog channels, is described. Results of various tests performed during the construction, installation and commissioning of the electronics mounted on the detector are presented. 10 refs., 12 figs.

  15. 2. GENERAL VIEW OF LAUNCH PAD B SHOWING (LEFT TO ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    2. GENERAL VIEW OF LAUNCH PAD B SHOWING (LEFT TO RIGHT) MOBILE SERVICE STRUCTURE, CONSTRUCTION CRANE, NEW CONCRETE FLAME DEFLECTORS AND FLUME, AND UMBILICAL MAST; VIEW TO NORTHWEST. - Cape Canaveral Air Station, Launch Complex 17, Facility 28402, East end of Lighthouse Road, Cape Canaveral, Brevard County, FL

  16. 20. GENERAL VIEW OF LAUNCH PAD B SHOWING UMBILICAL MAST ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    20. GENERAL VIEW OF LAUNCH PAD B SHOWING UMBILICAL MAST CENTER AND NEW BLAST BERM FOR NEW TANK FARM AT RIGHT VIEW TO NORTH. - Cape Canaveral Air Station, Launch Complex 17, Facility 28402, East end of Lighthouse Road, Cape Canaveral, Brevard County, FL

  17. RS-88 Rocket Engine Tested for Pad Abort Escape System

    NASA Technical Reports Server (NTRS)

    2003-01-01

    In this photo, an RS-88 development rocket engine is being test fired at NASA's Marshall Space Flight Center in Huntsville, Alabama, in support of the Pad Abort Demonstration (PAD) test flights for NASA's Orbital Space Plane (OSP). The tests could be instrumental in developing the first crew launch escape system in almost 30 years. Paving the way for a series of integrated PAD test flights, the engine tests support development of a system that could pull a crew safely away from danger during liftoff. A series of 16 hot fire tests of a 50,000-pound thrust RS-88 rocket engine were conducted, resulting in a total of 55 seconds of successful engine operation. The engine is being developed by the Rocketdyne Propulsion and Power unit of the Boeing Company. Integrated launch abort demonstration tests in 2005 will use four RS-88 engines to separate a test vehicle from a test platform, simulating pulling a crewed vehicle away from an aborted launch. Four 156-foot parachutes will deploy and carry the vehicle to landing. Lockheed Martin is building the vehicles for the PAD tests. Seven integrated tests are plarned for 2005 and 2006.

  18. RS-88 Rocket Engine Tested for Pad Abort Escape System

    NASA Technical Reports Server (NTRS)

    2003-01-01

    This photo gives an overhead look at an RS-88 development rocket engine being test fired at NASA's Marshall Space Flight Center in Huntsville, Alabama, in support of the Pad Abort Demonstration (PAD) test flights for NASA's Orbital Space Plane (OSP). The tests could be instrumental in developing the first crew launch escape system in almost 30 years. Paving the way for a series of integrated PAD test flights, the engine tests support development of a system that could pull a crew safely away from danger during liftoff. A series of 16 hot fire tests of a 50,000-pound thrust RS-88 rocket engine were conducted, resulting in a total of 55 seconds of successful engine operation. The engine is being developed by the Rocketdyne Propulsion and Power unit of the Boeing Company. Integrated launch abort demonstration tests in 2005 will use four RS-88 engines to separate a test vehicle from a test platform, simulating pulling a crewed vehicle away from an aborted launch. Four 156-foot parachutes will deploy and carry the vehicle to landing. Lockheed Martin is building the vehicles for the PAD tests. Seven integrated tests are plarned for 2005 and 2006.

  19. 6. View, flare and oxygen burner pad near southwest side ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    6. View, flare and oxygen burner pad near southwest side of Components Test Laboratory (T-27), looking northeast. Uphill and to the left of the flare is the Oxidizer Conditioning Structure (T-28D) and the Long-Term Oxidizer Silo (T-28B). - Air Force Plant PJKS, Systems Integration Laboratory, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

  20. Day of Launch Profile Selection for Pad Abort Guidance

    NASA Technical Reports Server (NTRS)

    Whitley, Ryan J.

    2010-01-01

    A day of launch selection approach that involves choosing from an array of pitch profiles of varying loft was analyzed with the purpose of reducing the risk of a land landing failure during a pad abort. It was determined that selecting from three pitch profiles can reduce the number of waterline abort performance requirement failures approximately in half without compromising other performance metrics.

  1. STS-107 Columbia on Launch Pad 39A after rollout

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- Space Shuttle Columbia sits on Launch Pad 39A, atop the Mobile Launcher Platform. The STS-107 research mission comprises experiments ranging from material sciences to life sciences, plus the Fast Reaction Experiments Enabling Science, Technology, Applications and Research (FREESTAR) that incorporates eight high priority secondary attached shuttle experiments. Mission STS-107 is scheduled to launch Jan. 16, 2003.

  2. Cost Beneftt Analysts of LH2 PadB

    NASA Technical Reports Server (NTRS)

    Mott, Brittany

    2013-01-01

    This analysis is used to evaluate, from a cost and benefit perspective, potential outcomes when replacing the pressurization switches and the pressurization system to meet the needs of the LH2 storage system at Pad B. This also includes alternatives, tangible and intangible benefits, and the results of the analysis.

  3. The floating cardiac fat pad-sign of occult pneumothorax.

    PubMed

    Kaufman, Claire; Bokhari, S A Jamal

    2016-08-01

    Pneumothoraces are a possible sequela of chest trauma with potential morbidity and mortality if not recognized and treated promptly. A portable supine chest radiograph is frequently the first radiologic study performed in the setting of trauma. While large pneumothoraces can be readily recognized on these radiographs, smaller pneumothoraces are missed in up to 15 % of trauma patients. There are many radiographic signs of occult pneumothoraces, and we are presenting a new radiographic sign of occult pneumothorax. The floating cardiac fat pad sign occurs when pleural air collects anteriorly and superiorly in the most non-dependent portion of the chest lifting the pericardial fat pad off the diaphragm. Lung markings are still seen surrounding the pericardial fat pad due to the inflated lower lobe of the lung resting dependently. Rapid and accurate identification of pneumothoraces is critical but often difficult on chest radiographs. Although there are many existing radiographic signs for identification of pneumothorax, prospective identification of small pneumothoraces is still relatively poor. Here, we describe an additional sign which aides in the detection of pneumothoraces, the floating cardiac fat pad. When present, this should prompt further evaluation with chest CT or upright chest radiograph. PMID:27250975

  4. Prevent P.A.D.: Know Your Numbers

    MedlinePlus

    ... the progression of P.A.D.," she adds. African Americans at Risk African Americans have a particularly high prevalence of risk factors ... have high blood pressure, hypertension, and diabetes. Further, African Americans, especially women, tend toward obesity and inactivity. The ...

  5. The Importance of Managing iPads in the Classroom

    ERIC Educational Resources Information Center

    Gentile, Mark

    2012-01-01

    Today, corporate users are not the only ones rapidly embracing mobile tablets for daily use--this transition has spilled over into the education sector. Schools have begun incorporating mobile devices such as iPads and other tablets into their curriculum. While this trend brings new and exciting educational opportunities, administrators and…

  6. 7. OVERALL VIEW OF LAUNCH PAD, SHOWING HELIPAD AT LAUNCH ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    7. OVERALL VIEW OF LAUNCH PAD, SHOWING HELIPAD AT LAUNCH AREA, WHEN VIEWED WITH NEGATIVE NO. CA-57-8(BELOW), LOOKING NORTH. BASKETBALL COURT IN BACKGROUND Everett Weinreb, photographer, March 1988 - Mount Gleason Nike Missile Site, Angeles National Forest, South of Soledad Canyon, Sylmar, Los Angeles County, CA

  7. Ereaders, the iPad--Is That All There Is?

    ERIC Educational Resources Information Center

    Lankes, R. David

    2010-01-01

    The device industry is blowing a great opportunity to revolutionize reading. At the Consumer Electronics Show in January, a dozen or more ebook readers and tablets were trotted out as the wave of the future. Since then, Apple has revealed the iPad, Sony has started shipping a touchscreen version of its eBook, and Spring Design has started shipping…

  8. Teaching, Learning, and Living with iPads

    ERIC Educational Resources Information Center

    Riley, Patricia

    2013-01-01

    Tablet computers, engaging and dynamic teaching and learning tools, are increasingly prevalent in K-12 schools and university settings. To help music educators make informed technology choices for their classrooms, this article contains preservice teachers' reflections on how they used iPads to enhance their musicianship, teacher preparation,…

  9. Re-Imagine Your Library with iPads

    ERIC Educational Resources Information Center

    Perez, Lisa

    2013-01-01

    Chicago Public Schools librarians have discovered that iPads engage students in developing their reading, writing, speaking, and listening skills while expressing their creativity. Their librarians embarked on a year-long experiment with the mobile devices that inspired them to completely reinvent the way they teach. This article presents tips…

  10. CONCRETE PAD AND SUSPENSION BRIDGE TOWERS FOR CABLES FORMERLY SUPPORTING ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    CONCRETE PAD AND SUSPENSION BRIDGE TOWERS FOR CABLES FORMERLY SUPPORTING THE SUSPENSION BRIDGE PORTION OF VALVE TOWER FOOT BRIDGE. VIEW FACING NORTHEAST - Schofield Barracks Military Reservation, Ku Tree Reservoir, Valve Tower Foot Bridge, Kalakoa Stream, East Range, Wahiawa, Honolulu County, HI

  11. Using the iPad in a Sport Education Season

    ERIC Educational Resources Information Center

    Sinelnikov, Oleg A.

    2012-01-01

    The latest advances in technology are inevitably making their way into schools and gymnasiums across the country. This article provides a descriptive account of how one physical education teacher incorporated the use of an iPad in a middle-school volleyball sport education season. The salient structural elements of sport education, such as…

  12. Approximate Solution for Choked Flow in Gas Seal Pads

    NASA Technical Reports Server (NTRS)

    Fleming, David P.

    2004-01-01

    Previous analyses of high pressure seals have considered adiabatic flow with friction but neglected effects of seal rotation. Most of this work analyzed a one-dimensional flow field. This works well to calculate stiffness and leakage of full circular seals, either face seals or annular ring seals. However, it cannot provide accurate results for a rectangular seal pad with its strongly two-dimensional flow field and its reliance on hydrodynamic forces to maintain a full fluid film. On the other hand, solutions of Reynolds lubrication equation have been obtained for the two-dimensional flow in a seal pad. But these solutions do not account for choking which occurs at high seal pressure ratios, nor do they consider the pressure loss that occurs in the entrance region of the flow field. The aim of the present work is to build on the Reynolds equation solution by use of an approximate choked flow analysis. This will account for the pressure losses in the flow entrance region, ensure that fluid velocities remain subsonic, and enable fluid inertial effects within the pad film to be accounted for. Results show that, in general, fluid inertia acts to decrease pad film load capacity and leakage, and increase film stiffness.

  13. Treating P.A.D. | NIH MedlinePlus the Magazine

    MedlinePlus

    ... turn Javascript on. Feature: Peripheral Artery Disease Treating P.A.D. Past Issues / Fall 2011 Table of ... provider to develop a supervised weight loss plan. P.A.D. Glossary Ankle-brachial index (ABI) A ...

  14. Your P.A.D. Checklist | NIH MedlinePlus the Magazine

    MedlinePlus

    ... turn Javascript on. Feature: Peripheral Artery Disease Your P.A.D. Checklist Past Issues / Fall 2011 Table ... and reduce your risk of peripheral artery disease (P.A.D.). That can start by making sure ...

  15. Treating P.A.D. | NIH MedlinePlus the Magazine

    MedlinePlus

    ... on. Feature: Peripheral Artery Disease Treating P.A.D. Past Issues / Fall 2011 Table of Contents As ... develop a supervised weight loss plan. P.A.D. Glossary Ankle-brachial index (ABI) A simple test ...

  16. TID Test Results for 4th Generation iPad(TradeMark)

    NASA Technical Reports Server (NTRS)

    Guertin, S. M.; Allen, G. R.; McClure, S. S.; LaBel, K. A.

    2013-01-01

    TID testing of 4th generation iPads is reported. Of iPad subsystems, results indicate that the charging circuitry and display drivers fail at lowest TID levels. Details of construction are investigated for additional testing of components.

  17. The effect and clinical application of homemade tracheotomy incision nursing pads.

    PubMed

    Yao, Yachun; Xu, Li; Du, Kun; Zhang, Jiajun

    2014-09-01

    To investigate the effect and clinical application of the homemade tracheotomy incision nursing pads. 83 patients suffering tracheotomy were randomly divided into experimental and control groups. The experimental group was treated with the homemade tracheotomy incision nursing pads, and the control group was treated with the traditional tracheotomy nursing pads. Subsequently, the number of nursing pads used in 2 weeks, tracheotomy incision bacterial colonies and the comfort of patient between the two groups of pads was compared. The number of nursing pads used by the experimental group was smaller than the control group, and the tracheotomy incision bacterial colonies in the experimental group were fewer than the control group (P < 0.01). However, the differences observed for the skin irritation and gas permeability between the two groups were not statistically significant (P > 0.05). Thus, the results show that the effect of homemade tracheotomy incision nursing pads is greater compared to the traditional nursing pads. PMID:24633484

  18. Arachnids Secrete a Fluid over Their Adhesive Pads

    PubMed Central

    Peattie, Anne M.; Dirks, Jan-Henning; Henriques, Sérgio; Federle, Walter

    2011-01-01

    Background Many arachnids possess adhesive pads on their feet that help them climb smooth surfaces and capture prey. Spider and gecko adhesives have converged on a branched, hairy structure, which theoretically allows them to adhere solely by dry (solid-solid) intermolecular interactions. Indeed, the consensus in the literature is that spiders and their smooth-padded relatives, the solifugids, adhere without the aid of a secretion. Methodology and Principal Findings We investigated the adhesive contact zone of living spiders, solifugids and mites using interference reflection microscopy, which allows the detection of thin liquid films. Like insects, all the arachnids we studied left behind hydrophobic fluid footprints on glass (mean refractive index: 1.48–1.50; contact angle: 3.7–11.2°). Fluid was not always secreted continuously, suggesting that pads can function in both wet and dry modes. We measured the attachment forces of single adhesive setae from tarantulas (Grammostola rosea) by attaching them to a bending beam with a known spring constant and filming the resulting deflection. Individual spider setae showed a lower static friction at rest (26%±2.8 SE of the peak friction) than single gecko setae (Thecadactylus rapicauda; 96%±1.7 SE). This may be explained by the fact that spider setae continued to release fluid after isolation from the animal, lubricating the contact zone. Significance This finding implies that tarsal secretions occur within all major groups of terrestrial arthropods with adhesive pads. The presence of liquid in an adhesive contact zone has important consequences for attachment performance, improving adhesion to rough surfaces and introducing rate-dependent effects. Our results leave geckos and anoles as the only known representatives of truly dry adhesive pads in nature. Engineers seeking biological inspiration for synthetic adhesives should consider whether model species with fluid secretions are appropriate to their design goals

  19. 40 CFR 265.441 - Assessment of existing drip pad integrity.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 25 2010-07-01 2010-07-01 false Assessment of existing drip pad integrity. 265.441 Section 265.441 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED..., STORAGE, AND DISPOSAL FACILITIES Drip Pads § 265.441 Assessment of existing drip pad integrity. (a)...

  20. 40 CFR 264.571 - Assessment of existing drip pad integrity.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 25 2010-07-01 2010-07-01 false Assessment of existing drip pad integrity. 264.571 Section 264.571 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... DISPOSAL FACILITIES Drip Pads § 264.571 Assessment of existing drip pad integrity. (a) For each...

  1. Use of Doceri Software for iPad in Online Delivery of Chemistry Content

    ERIC Educational Resources Information Center

    Silverberg, Lee J.; Tierney, John; Bodek, Matthew J.

    2014-01-01

    Doceri software for iPad is useful for both synchronous online and asynchronous online delivery of chemistry course content. Using the Doceri wireless connection between the iPad and a personal computer that is running Adobe Connect, online synchronous instruction can be accomplished in which drawings can be completed by hand on the iPad. For…

  2. A Fluopol-ABPP HTS Assay to Identify PAD Inhibitors†‡

    PubMed Central

    Knuckley, Bryan; Jones, Justin E.; Bachovchin, Daniel A.; Slack, Jessica; Causey, Corey P.; Brown, Steven J.; Rosen, Hugh; Cravatt, Benjamin F.; Thompson, Paul R.

    2010-01-01

    Protein Arginine Deiminase (PAD) activity is dysregulated in numerous diseases, e.g., Rheumatoid Arthritis. Herein we describe the development of a fluorescence polarization-Activity Based Protein Profiling (fluopol-ABPP) based high throughput screening assay that can be used to identify PAD-selective inhibitors. Using this assay, streptonigrin was identified as a potent, selective, and irreversible PAD4 inactivator. PMID:20740228

  3. 40 CFR 265.441 - Assessment of existing drip pad integrity.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 26 2011-07-01 2011-07-01 false Assessment of existing drip pad integrity. 265.441 Section 265.441 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED..., STORAGE, AND DISPOSAL FACILITIES Drip Pads § 265.441 Assessment of existing drip pad integrity. (a)...

  4. 40 CFR 264.571 - Assessment of existing drip pad integrity.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 26 2011-07-01 2011-07-01 false Assessment of existing drip pad integrity. 264.571 Section 264.571 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... DISPOSAL FACILITIES Drip Pads § 264.571 Assessment of existing drip pad integrity. (a) For each...

  5. 77 FR 50508 - Brain-Pad, Inc; Analysis of Proposed Consent Order To Aid Public Comment

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-08-21

    ... Brain-Pad, Inc; Analysis of Proposed Consent Order To Aid Public Comment AGENCY: Federal Trade... SUPPLEMENTARY INFORMATION section below. Write ``Brain-Pad, File No. 122 3073'' on your comment, and file your... must receive it on or before September 17, 2012. Write ``Brain-Pad, File No. 122 3073'' on your...

  6. Functionally Different Pads on the Same Foot Allow Control of Attachment: Stick Insects Have Load-Sensitive “Heel” Pads for Friction and Shear-Sensitive “Toe” Pads for Adhesion

    PubMed Central

    Labonte, David; Federle, Walter

    2013-01-01

    Stick insects (Carausius morosus) have two distinct types of attachment pad per leg, tarsal “heel” pads (euplantulae) and a pre-tarsal “toe” pad (arolium). Here we show that these two pad types are specialised for fundamentally different functions. When standing upright, stick insects rested on their proximal euplantulae, while arolia were the only pads in surface contact when hanging upside down. Single-pad force measurements showed that the adhesion of euplantulae was extremely small, but friction forces strongly increased with normal load and coefficients of friction were 1. The pre-tarsal arolium, in contrast, generated adhesion that strongly increased with pulling forces, allowing adhesion to be activated and deactivated by shear forces, which can be produced actively, or passively as a result of the insects' sprawled posture. The shear-sensitivity of the arolium was present even when corrected for contact area, and was independent of normal preloads covering nearly an order of magnitude. Attachment of both heel and toe pads is thus activated partly by the forces that arise passively in the situations in which they are used by the insects, ensuring safe attachment. Our results suggest that stick insect euplantulae are specialised “friction pads” that produce traction when pressed against the substrate, while arolia are “true” adhesive pads that stick to the substrate when activated by pulling forces. PMID:24349156

  7. Space Shuttle Discovery rolls out to the launch pad

    NASA Technical Reports Server (NTRS)

    1999-01-01

    The Space Shuttle Discovery, atop the mobile launcher platform and crawler-transporter, approaches the turn in the crawlerway as it creeps to Launch Pad 39B at 1 mph. The crawler-transporter takes about five hours to cover the 4.2 miles from the Vehicle Assembly Building to the launch pad. Liftoff of Discovery on mission STS-96 is targeted for May 20 at 9:32 a.m. EDT. STS-96 is a logistics and resupply mission for the International Space Station, carrying such payloads as a Russian crane, the Strela; a U.S.-built crane; the Spacehab Oceaneering Space System Box (SHOSS), a logistics items carrier; and STARSHINE, a student-led experiment.

  8. Space Shuttle Discovery rolls out to the launch pad

    NASA Technical Reports Server (NTRS)

    1999-01-01

    The Space Shuttle Discovery, atop the mobile launcher platform and crawler-transporter, dwarfs the car parked at right on the median of the 130-foot-wide crawlerway. Traveling at 1 mph, the crawler-transporter takes about five hours to cover the 4.2 miles from the Vehicle Assembly Building to Launch Pad 39B. Here it is moving toward the turn that will take it to the pad. Liftoff of Discovery on mission STS-96 is targeted for May 20 at 9:32 a.m. EDT. STS-96 is a logistics and resupply mission for the International Space Station, carrying such payloads as a Russian crane, the Strela; a U.S.-built crane; the Spacehab Oceaneering Space System Box (SHOSS), a logistics items carrier; and STARSHINE, a student-led experiment.

  9. Pad polishing for rapid production of large flats

    NASA Astrophysics Data System (ADS)

    Berggren, Ralph R.; Schmell, Rodney A.

    1997-10-01

    Pad polishing is an efficient technique for polishing-out a ground surface and reaching a figure better than one wave, ready for completion with less than an hour on a planetary polisher. Recent work has shown success on 350 mm square parts; current work involves scaling the process to 1.4 meter diameter. For the 350 mm square piece of BK7, removal was one micrometer every 10 minutes. Polishing-out from a 5 micrometer grind took less than 3 hours, to a surface smoothness of one nm rms. Other tests verified that the pad leaves no unusual subsurface damage. Following completion on a pitch planetary polisher, surface finish is the same as obtained for conventional processing.

  10. Carbon-Nanotube-Carpet Heat-Transfer Pads

    NASA Technical Reports Server (NTRS)

    Li, Jun; Cruden, Brett A.; Cassel, Alan M.

    2006-01-01

    Microscopic thermal-contact pads that include carpet-like arrays of carbon nanotubes have been invented for dissipating heat generated in integrated circuits and similarly sized single electronic components. The need for these or other innovative thermal-contact pads arises because the requisite high thermal conductances cannot be realized by scaling conventional macroscopic thermal-contact pads down to microscopic sizes. Overcoming limitations of conventional thermal-contact materials and components, the carbon-nanotube thermal-contact pads offer the high thermal conductivities needed to accommodate the high local thermal power densities of modern electronic circuits, without need for large clamping pressures, extreme smoothness of surfaces in contact, or gap-filling materials (e.g., thermally conductive greases) to ensure adequate thermal contact. Moreover, unlike some conventional thermal-contact components, these pads are reusable. The figure depicts a typical pad according to the invention, in contact with a rough surface on an electronic component that is to be cooled. Through reversible bending and buckling of carbon nanotubes at asperities on the rough surface, the pad yields sufficiently, under relatively low contact pressure, that thermal contact is distributed to many locations on the surface to be cooled, including valleys where contact would not ordinarily occur in conventional clamping of rigid surfaces. Hence, the effective thermal-contact area is greater than that achievable through scaling down of a macroscopic thermal-contact pad. The extremely high longitudinal thermal conductivities of the carbon nanotubes are utilized to conduct heat away from potential hot spots on the surface to be cooled. The fibers protrude from a layer of a filler material (Cu, Ag, Au, or metal-particle- filled gels), which provides both mechanical support to maintain the carbon nanotubes in alignment and thermal conductivity to enhance the diffusion of concentrated heat

  11. STS-93 Columbia after rollout to Launch Pad 39B

    NASA Technical Reports Server (NTRS)

    1999-01-01

    Space Shuttle Columbia sits on Launch Pad 39B less than two weeks after liftoff of Discovery on mission STS-96. Columbia was rolled out June 7 in preparation for the launch of STS-93 with its payload of the Chandra X-ray Observatory. The Rotating Service Structure will be moved into place around it on Tuesday, June 8. With the world's most powerful X-ray telescope, Chandra will allow scientists from around the world to see previously invisible black holes and high-temperature gas clouds, giving the observatory the potential to rewrite the books on the structure and evolution of our universe. Columbia (OV-102) is the first of NASA's orbiter fleet, delivered to Kennedy Space Center in March 1979. Columbia initiated the Space Shuttle flight program at KSC when it lifted off Launch Pad 39A on April 12, 1981.

  12. STS-93 Columbia after rollout to Launch Pad 39B

    NASA Technical Reports Server (NTRS)

    1999-01-01

    This closeup of Space Shuttle Columbia on Launch Pad 39B shows the Rotating Service Structure, at left, which will be moved into place on Tuesday, June 8. Columbia was rolled out June 7, less than two weeks after the liftoff of Discovery on mission STS-96, in preparation for the launch of STS-93. The mission payload is the Chandra X-ray Observatory, the world's most powerful X-ray telescope, which will allow scientists from around the world to see previously invisible black holes and high-temperature gas clouds, giving the observatory the potential to rewrite the books on the structure and evolution of our universe. Columbia (OV-102) is the first of NASA's orbiter fleet, delivered to Kennedy Space Center in March 1979. Columbia initiated the Space Shuttle flight program at KSC when it lifted off Launch Pad 39A on April 12, 1981.

  13. STS-93 Columbia after rollout to Launch Pad 39B

    NASA Technical Reports Server (NTRS)

    1999-01-01

    Space Shuttle Columbia sits on Launch Pad 39B less than two weeks after liftoff of Discovery on mission STS-96. Columbia was rolled out June 7 in preparation for the launch of STS-93 with its payload of the Chandra X-ray Observatory. The Rotating Service Structure, at left, will be moved into place on Tuesday, June 8. With the world's most powerful X-ray telescope, Chandra will allow scientists from around the world to see previously invisible black holes and high-temperature gas clouds, giving the observatory the potential to rewrite the books on the structure and evolution of our universe. Columbia (OV-102) is the first of NASA's orbiter fleet, delivered to Kennedy Space Center in March 1979. Columbia initiated the Space Shuttle flight program at KSC when it lifted off Launch Pad 39A on April 12, 1981.

  14. Pad readout for gas detectors using 128-channel integrated preamplifiers

    SciTech Connect

    Fischer, P.; Drees, A.; Glassel, P.; Lamade, G.; Ries, H.; Schon, A.; Specht, H.; Breskin, A.; Chechik, R.; Fraenkel, Z.

    1988-02-01

    A novel two-dimensional readout scheme for gas detectors is presented which uses small metal pads with 2.54 mm pitch as an anode. The pads are read out via 128-channel VLSI low-noise preamplifier/multiplexer chips. These chips are mounted on 2.8x2.8 cm/sup 2/ modules which are directly plugged onto the detector backplane, daisy-chained with jumpers and read out sequentially. The readout has been successfully tested with a low-pressure, two-step, TMAE-filled UV-RICH detector prototype. A single electron efficiently of >90% was observed at moderate chamber gains (<10/sup 6/). The method offers high electronic amplification, low noise, and high readout speed with a very flexible and compact design, suited for space-limited applications.

  15. Nanoscale friction and adhesion of tree frog toe pads.

    PubMed

    Kappl, Michael; Kaveh, Farzaneh; Barnes, W Jon P

    2016-01-01

    Tree frogs have become an object of interest in biomimetics due to their ability to cling to wet and slippery surfaces. In this study, we have investigated the adhesion and friction behavior of toe pads of White's tree frog (Litoria caerulea) using atomic force microscopy (AFM) in an aqueous medium. Facilitating special types of AFM probes with radii of ∼400 nm and ∼13 μm, we were able to sense the frictional response without damaging the delicate nanopillar structures of the epithelial cells. While we observed no significant adhesion between both types of probes and toe pads in wet conditions, frictional forces under such conditions were very pronounced and friction coefficients amounted between 0.3 and 1.1 for the sliding friction between probes and the epithelial cell surfaces. PMID:27165465

  16. STS-81 Rollout to Pad 39B (turtle in foreground)

    NASA Technical Reports Server (NTRS)

    1996-01-01

    Will the Space Shuttle Atlantis or the turtle reach Launch Pad 39B first? Carried atop the Mobile Launch Platform on the 6- million-pound Crawler Transporter, Shuttle Atlantis departs the Vehicle Assembly Building en route to Pad B at a maximum speed of 1 mile per hour. No one clocked the turtle, which seems to be heading in the same direction. Atlantis is tentatively scheduled to lift off on a nine-day mission on Jan. 12. STS-81 will be the fifth Shuttle-Mir docking. The six-member crew at liftoff will include Mission Specialist J.M. Linenger, who will transfer to the Russian Mir Space Station for an extended stay, replacing astronaut John E. Blaha, who will return to Earth on Atlantis.

  17. One-Time Pad as a nonlinear dynamical system

    NASA Astrophysics Data System (ADS)

    Nagaraj, Nithin

    2012-11-01

    The One-Time Pad (OTP) is the only known unbreakable cipher, proved mathematically by Shannon in 1949. In spite of several practical drawbacks of using the OTP, it continues to be used in quantum cryptography, DNA cryptography and even in classical cryptography when the highest form of security is desired (other popular algorithms like RSA, ECC, AES are not even proven to be computationally secure). In this work, we prove that the OTP encryption and decryption is equivalent to finding the initial condition on a pair of binary maps (Bernoulli shift). The binary map belongs to a family of 1D nonlinear chaotic and ergodic dynamical systems known as Generalized Luröth Series (GLS). Having established these interesting connections, we construct other perfect secrecy systems on the GLS that are equivalent to the One-Time Pad, generalizing for larger alphabets. We further show that OTP encryption is related to Randomized Arithmetic Coding - a scheme for joint compression and encryption.

  18. Extreme Meteorological Parameters During Space Shuttle Pad Exposure Periods

    NASA Technical Reports Server (NTRS)

    Roberts, Barry C.; Overbey, B. Glenn

    2004-01-01

    During the 113 missions of the Space Transportation System (STS), the Space Shuttle fleet has been exposed to the elements on the launch pad for a total of 4195 days. This paper provides a summary of the historical record of the meteorological extremes encountered by the Space Shuttle fleet during the pad exposure period. Parameters included are temperature, dew point, relative humidity, wind speed, sea level pressure and precipitation. All the data presented are archived by the Marshall Space Flight Center Environments Group, and were obtained from a combination of surface observations and meteorological towers at Kennedy Space Center (KSC), Florida. Data are provided from the first launch of the STS in 1981 through the launch of STS-107 in 2003.

  19. Space Shuttle Discovery rolls out to the launch pad

    NASA Technical Reports Server (NTRS)

    1999-01-01

    The Space Shuttle Discovery, atop the mobile launcher platform and crawler-transporter, begins the climb up the ramp to Launch Pad 39B. Traveling at 1 mph, the crawler-transporter takes about five hours to cover the 4.2 miles from the Vehicle Assembly Building to the launch pad. Special levelers on the crawler- transporter keep the Space Shuttle vertical within plus or minus 10 minutes of arc about the dimensions of a basketball. Liftoff of Discovery on mission STS-96 is targeted for May 20 at 9:32 a.m. EDT. STS-96 is a logistics and resupply mission for the International Space Station, carrying such payloads as a Russian crane, the Strela; a U.S.-built crane; the Spacehab Oceaneering Space System Box (SHOSS), a logistics items carrier; and STARSHINE, a student-led experiment.

  20. Orion Pad Abort 1 GN and C Design and Development

    NASA Technical Reports Server (NTRS)

    Medina, Edgar A.; Stachowiak, Susan J.

    2010-01-01

    The first flight test of the Orion Abort Flight Test project is scheduled to launch in Spring 2010. This flight test is known as Pad Abort 1 (PA-1) and it is intended to accomplish a series of flight test objectives, including demonstrating the capability of the Launch Abort System (LAS) to propel the Crew Module (CM) to a safe distance from a launch vehicle during a pad abort. The PA-1 Flight Test Article (FTA) is actively controlled by a guidance, navigation, and control (GN&C) system for much of its flight. The purpose of this paper is to describe the design, development, and analysis of the PA-1 GN&C system. A description of the technical solutions that were developed to meet the challenge of satisfying many competing requirements is presented. A historical perspective of how the Orion LAV compares to the Apollo Launch Escape Vehicle (LEV) design will also be included.

  1. Pad A Main Flame Deflector Sensor Data and Evaluation

    NASA Technical Reports Server (NTRS)

    Parlier, Christopher R.

    2011-01-01

    Space shuttle launch pads use flame deflectors beneath the vehicle to channel hot gases away from the vehicle. Pad 39 A at the Kennedy Space Center uses a steel structure coated with refractory concrete. The solid rocket booster plume is comprised of gas and molten alumina oxide particles that erodes the refractory concrete. During the beginning of the shuttle program the loads for this system were never validated with a high level of confidence. This paper presents a representation of the instrumentation data collected and follow on materials science evaluation of the materials exposed to the SRB plume. Data collected during STS-133 and STS-134 will be presented that support the evaluation of the components exposed to the SRB plume.

  2. The STS-98 crew practices emergency egress from the pad

    NASA Technical Reports Server (NTRS)

    2001-01-01

    KENNEDY SPACE CENTER, Fla. -- STS-98 Mission Specialists Robert Curbeam, Marsha Ivins and Thomas Jones try out the three-person slidewire basket, part of the equipment used for emergency egress from the launch pad. The basket slides along a 1200-foot wire to the landing zone below and nearby bunker. The crew has been taking part in Terminal Countdown Demonstration Test activities, which include the simulated countdown and emergency egress training at the pad. STS-98 is the seventh construction flight to the International Space Station, carrying as payload the U.S. Lab Destiny, a key element in the construction of the ISS. Launch of STS-98 is scheduled for Jan. 19 at 2:11 a.m. EST.

  3. Wet but not slippery: boundary friction in tree frog adhesive toe pads

    PubMed Central

    Federle, W; Barnes, W.J.P; Baumgartner, W; Drechsler, P; Smith, J.M

    2006-01-01

    Tree frogs are remarkable for their capacity to cling to smooth surfaces using large toe pads. The adhesive skin of tree frog toe pads is characterized by peg-studded hexagonal cells separated by deep channels into which mucus glands open. The pads are completely wetted with watery mucus, which led previous authors to suggest that attachment is solely due to capillary and viscous forces generated by the fluid-filled joint between the pad and the substrate. Here, we present evidence from single-toe force measurements, laser tweezer microrheometry of pad mucus and interference reflection microscopy of the contact zone in Litoria caerulea, that tree frog attachment forces are significantly enhanced by close contacts and boundary friction between the pad epidermis and the substrate, facilitated by the highly regular pad microstructure. PMID:16971337

  4. Fine structure of the adhesive pads of Gonionemus vertens.

    PubMed

    Singla, C L

    1977-07-15

    The adhesive pads of Gonionemus vertens, located near the distal end of each tentacle, consist of a layer of columnar glandulomuscular cells surrounded by a collar of microfilament containing epithelial cells. The glandulomuscular cells contain dense secretory rods, microtubules, rough endoplasmic reticulum, Golgi elements and myonemes. Axons located between the basal portions of the glandulomuscular cells form synapses with the glandulomuscular cells. The roles of these various cell organelles in adhesion and detachment process are discussed. PMID:18289

  5. Orion Pad Abort 1 Flight Test - Ground and Flight Operations

    NASA Technical Reports Server (NTRS)

    Hackenbergy, Davis L.; Hicks, Wayne

    2011-01-01

    This paper discusses the ground and flight operations aspects to the Pad Abort 1 launch. The paper details the processes used to plan all operations. The paper then discussions the difficulties of integration and testing, while detailing some of the lessons learned throughout the entire launch campaign. Flight operational aspects of the launc are covered in order to provide the listener with the full suite of operational issues encountered in preparation for the first flight test of the Orion Launch Abort System.

  6. ClimatePad: Enabling public exploration of climate data

    NASA Astrophysics Data System (ADS)

    Walsh, J. E.; Chapman, W. L.

    2012-12-01

    Informal learners interested in climate issues can find a wealth of information in the print and online media related to climate and climate change. Throughout these resources, the equal use of generic terms like 'global warming' and 'climate change' suggest a level of nuance in the science that is not easy to convey in this conventional media. Perhaps more than any other discipline, climate literacy has the most potential to be enhanced via the process of cognitive construction and reconstruction, rather than simple transmission of knowledge. Constructionism suggests that meaningful learning happens most effectively if the learner is actively engaged in constructing a product in the real world rather than absorbing information passively. Recent technological innovations have introduced mobile computing devices with sufficient power to do serious data analysis. The potential of these devices to augment climate literacy by turning citizens into scientists has yet to be exploited. We introduce ClimatePad, an iPad application that permits students and public to actively browse climate datasets, construct trends, plot time series, create composite differences and view animations of real-world climate data. Interactions with the ClimatePad permits varying the starting and ending dates of trends and differences. Climate analysis maps and animations can be customized with different color palettes, enticing the user to delve into and absorb the subtleties of the regional and temporal variations of the recent climate record. Finally, user-generated climate visualizations created with ClimatePad can be emailed to friends and shared via Facebook, entraining even more active learners.

  7. Liquid transmission characteristics of padding bandages under pressure.

    PubMed

    Kumar, Bipin; Das, Apurba; Pan, Ning; Alagirusamy, R; Gupta, Rupali; Singh, Jitender

    2015-11-01

    Padding is an essential component in a multilayer compression bandaging system, used inside the compression bandage through which substantial amount of pressure is exerted on the limb of patient for treatment of venous leg ulcers. As a result, the liquid transmission behavior of padding is also critical in managing body fluids or sweat exuded from the affected limb, reducing the excessive moisture build-up around the wound and thereby ensuring comfort to and hence a better compliance from the patients. This study investigates the in-plane fluid transport characteristics of needle-punched nonwoven padding bandages. It first reviewed the existing studies related to the problems, and discussed their limits and possible improvements in dealing with complex fluid transport issues in textile porous media. The measurement of fluid transport under different pressure levels was then done using a newly designed apparatus capable of simultaneously tracing the liquid in-plane spreading along different directions, and obtaining several transport characteristics of a testing sample, e.g. the liquid flow anisotropy, the rate of movement, the area of wet surface with time, etc. Also the effects of several important factors, such as the levels of pressure applied, the specimen bulk density, and needling density of the padding products, have been experimentally investigated. In addition, based on an extended Lucas-Washburn theory, we calculated the liquid flow distance, both instantaneous speed and a more useful time-averaged speed v(av) at any given direction, and also defined a flow anisotropy index I(A) as a convenient parameter to represent the material flow anisotropy. The applications of v(av) and I(A) to actual samples have demonstrated the usefulness of these parameters in characterizing the flow nature and behavior of the materials. PMID:26228389

  8. Teaching and Learning with iPads, Ready or Not?

    ERIC Educational Resources Information Center

    Murray, Orrin T.; Olcese, Nicole R.

    2011-01-01

    Within weeks of becoming available, the iPad reportedly sold over 3 million units, a brisker pace than other tablets in the personal computer realm. Much of the early success might be attributed to the almost 250,000 applications that could run on the device and a similar interface to the popular iPod Touch and iPhone. This article considers…

  9. A Robot Emotion Generation Mechanism Based on PAD Emotion Space

    NASA Astrophysics Data System (ADS)

    Qingji, Gao; Kai, Wang; Haijuan, Liu

    A robot emotion generation mechanism is presented in this paper, in which emotion is described in PAD emotion space. In this mechanism, emotion is affected by the robot personality, the robot task and the emotion origin, so the robot emotion will change naturally when it senses the extern stimuli. We also experiment on Fuwa robot, and demonstrate that this mechanism can make the robot's emotion change be more easily accepted by people and is good for human-robot interaction.

  10. Finger pad friction and its role in grip and touch

    PubMed Central

    Adams, Michael J.; Johnson, Simon A.; Lefèvre, Philippe; Lévesque, Vincent; Hayward, Vincent; André, Thibaut; Thonnard, Jean-Louis

    2013-01-01

    Many aspects of both grip function and tactile perception depend on complex frictional interactions occurring in the contact zone of the finger pad, which is the subject of the current review. While it is well established that friction plays a crucial role in grip function, its exact contribution for discriminatory touch involving the sliding of a finger pad is more elusive. For texture discrimination, it is clear that vibrotaction plays an important role in the discriminatory mechanisms. Among other factors, friction impacts the nature of the vibrations generated by the relative movement of the fingertip skin against a probed object. Friction also has a major influence on the perceived tactile pleasantness of a surface. The contact mechanics of a finger pad is governed by the fingerprint ridges and the sweat that is exuded from pores located on these ridges. Counterintuitively, the coefficient of friction can increase by an order of magnitude in a period of tens of seconds when in contact with an impermeably smooth surface, such as glass. In contrast, the value will decrease for a porous surface, such as paper. The increase in friction is attributed to an occlusion mechanism and can be described by first-order kinetics. Surprisingly, the sensitivity of the coefficient of friction to the normal load and sliding velocity is comparatively of second order, yet these dependencies provide the main basis of theoretical models which, to-date, largely ignore the time evolution of the frictional dynamics. One well-known effect on taction is the possibility of inducing stick–slip if the friction decreases with increasing sliding velocity. Moreover, the initial slip of a finger pad occurs by the propagation of an annulus of failure from the perimeter of the contact zone and this phenomenon could be important in tactile perception and grip function. PMID:23256185

  11. Mapping of Streptococcus faecalis plasmids pAD1 and pAD2 and studies relating to transposition of Tn917.

    PubMed Central

    Clewell, D B; Tomich, P K; Gawron-Burke, M C; Franke, A E; Yagi, Y; An, F Y

    1982-01-01

    Plasmids pAD1 (37.8 megadaltons) and pAD2 (17.1 megadaltons) of Streptococcus faecalis strain DS16 have been mapped with restriction enzymes. The location of a hemolysin-bacteriocin determinant on the conjugative pAD1 plasmid was derived from analyses of transposon insertions. Electron microscope and hybridization analyses located Tn917(Em) and the streptomycin (Sm) and kanamycin (Km) resistance determinants on the nonconjugative pAD2 plasmid. It was shown previously that the erythromycin (Em) resistance associated with Tn917 is inducible and that transposition from pAD2 to pAD1 is also stimulated by exposure of cells to low concentrations of Em. Here we show that inducing concentrations of Em also increase the conjugative transfer potential of pAD1; this is possibly related to a mild and short-lived inhibitory stress placed on the cells before full induction of resistance. Selection of Em-resistant transconjugants arising from matings between DS16 and a plasmid-free recipient gave rise to transconjugants which primarily harbor stable pAD1::pAD2 cointegrates. A 30-min exposure of donors to Em (0.5 microgram/ml) before mating resulted in a severalfold increase in the number of such transconjugants. However, a small fraction (e.g., 3 of 40) of these Emr Smr Kmr transconjugants harbored pAD1::Tn917 and pAD2 molecules. Since we believe pAD2 is incapable of being mobilized by pAD1 without being covalently linked, it is likely that transfer in these cases involved cointegrates representing structural intermediates in the transposition of Tn917 from pAD2 to pAD1. It follows that such intermediates probably had two copies of Tn917 and readily resolved after transfer. (These cointegrates are different from the stable cointegrates which were shown to have only a single copy of Tn917; the latter are assumed not to be related to transposition.) Two variants with altered Tn917 transposition properties were derived. One of them transposed at an elevated frequency, whereas the

  12. iPad colour vision apps for dyschromatopsia screening.

    PubMed

    Campbell, Thomas Gordon; Lehn, Alexander; Blum, Stefan; Airey, Caroline; Brown, Helen

    2016-07-01

    Optic neuritis (ON) is a common and important cause of vision loss or vision disturbances in the community, particularly amongst the young, and it is often associated with a persistent dyschromatopsia. Traditionally screening for dyschromatopsia has been carried out using pseudo-isochromatic Ishihara plates. These colour plates were originally developed for testing of colour blindness, and indeed have only more recently been applied to ON. As the Ishihara plate books used for testing are expensive, unwieldy, and are not commonly available in many clinics or wards, many neurologists and ophthalmologists have taken to using untested and unstudied downloadable software packages on portable electronic devices for testing. This study compared the efficacy of printed and iPad (Apple, Cupertino, CA, USA) versions of the Ishihara plates in screening for dyschromatopsia in patients who were suspected of having ON. The main finding was that dyschromatopsia testing using a commercially available application on an iPad was comparable to using the current pragmatic clinical benchmark, the pseudo-isochromatic plates of Ishihara. These findings provide support for the increasingly common practice of screening for dyschromatopsia using the iPad. PMID:26896905

  13. iPad: Semantic annotation and markup of radiological images.

    PubMed

    Rubin, Daniel L; Rodriguez, Cesar; Shah, Priyanka; Beaulieu, Chris

    2008-01-01

    Radiological images contain a wealth of information,such as anatomy and pathology, which is often not explicit and computationally accessible. Information schemes are being developed to describe the semantic content of images, but such schemes can be unwieldy to operationalize because there are few tools to enable users to capture structured information easily as part of the routine research workflow. We have created iPad, an open source tool enabling researchers and clinicians to create semantic annotations on radiological images. iPad hides the complexity of the underlying image annotation information model from users, permitting them to describe images and image regions using a graphical interface that maps their descriptions to structured ontologies semi-automatically. Image annotations are saved in a variety of formats,enabling interoperability among medical records systems, image archives in hospitals, and the Semantic Web. Tools such as iPad can help reduce the burden of collecting structured information from images, and it could ultimately enable researchers and physicians to exploit images on a very large scale and glean the biological and physiological significance of image content. PMID:18999144

  14. iPad: Semantic Annotation and Markup of Radiological Images

    PubMed Central

    Rubin, Daniel L.; Rodriguez, Cesar; Shah, Priyanka; Beaulieu, Chris

    2008-01-01

    Radiological images contain a wealth of information, such as anatomy and pathology, which is often not explicit and computationally accessible. Information schemes are being developed to describe the semantic content of images, but such schemes can be unwieldy to operationalize because there are few tools to enable users to capture structured information easily as part of the routine research workflow. We have created iPad, an open source tool enabling researchers and clinicians to create semantic annotations on radiological images. iPad hides the complexity of the underlying image annotation information model from users, permitting them to describe images and image regions using a graphical interface that maps their descriptions to structured ontologies semi-automatically. Image annotations are saved in a variety of formats, enabling interoperability among medical records systems, image archives in hospitals, and the Semantic Web. Tools such as iPad can help reduce the burden of collecting structured information from images, and it could ultimately enable researchers and physicians to exploit images on a very large scale and glean the biological and physiological significance of image content. PMID:18999144

  15. Mechanisms of fluid production in smooth adhesive pads of insects.

    PubMed

    Dirks, Jan-Henning; Federle, Walter

    2011-07-01

    Insect adhesion is mediated by thin fluid films secreted into the contact zone. As the amount of fluid affects adhesive forces, a control of secretion appears probable. Here, we quantify for the first time the rate of fluid secretion in adhesive pads of cockroaches and stick insects. The volume of footprints deposited during consecutive press-downs decreased exponentially and approached a non-zero steady state, demonstrating the presence of a storage volume. We estimated its size and the influx rate into it from a simple compartmental model. Influx was independent of step frequency. Fluid-depleted pads recovered maximal footprint volumes within 15 min. Pads in stationary contact accumulated fluid along the perimeter of the contact zone. The initial fluid build-up slowed down, suggesting that flow is driven by negative Laplace pressure. Freely climbing stick insects left hardly any traceable footprints, suggesting that they save secretion by minimizing contact area or by recovering fluid during detachment. However, even the highest fluid production rates observed incur only small biosynthesis costs, representing less than 1 per cent of the resting metabolic rate. Our results show that fluid secretion in insect wet adhesive systems relies on simple physical principles, allowing for passive control of fluid volume within the contact zone. PMID:21208970

  16. μ-PADs for detection of chemical warfare agents.

    PubMed

    Pardasani, Deepak; Tak, Vijay; Purohit, Ajay K; Dubey, D K

    2012-12-01

    Conventional methods of detection of chemical warfare agents (CWAs) based on chromogenic reactions are time and solvent intensive. The development of cost, time and solvent effective microfluidic paper based analytical devices (μ-PADs) for the detection of nerve and vesicant agents is described. The detection of analytes was based upon their reactions with rhodamine hydroxamate and para-nitrobenzyl pyridine, producing red and blue colours respectively. Reactions were optimized on the μ-PADs to produce the limits of detection (LODs) as low as 100 μM for sulfur mustard in aqueous samples. Results were quantified with the help of a simple desktop scanner and Photoshop software. Sarin achieved a linear response in the two concentration ranges of 20-100 mM and 100-500 mM, whereas the response of sulfur mustard was found to be linear in the concentration range of 10-75 mM. Results were precise enough to establish the μ-PADs as a valuable tool for security personnel fighting against chemical terrorism. PMID:23086107

  17. Analytic continuation by averaging Padé approximants

    NASA Astrophysics Data System (ADS)

    Schött, Johan; Locht, Inka L. M.; Lundin, Elin; Grânäs, Oscar; Eriksson, Olle; Di Marco, Igor

    2016-02-01

    The ill-posed analytic continuation problem for Green's functions and self-energies is investigated by revisiting the Padé approximants technique. We propose to remedy the well-known problems of the Padé approximants by performing an average of several continuations, obtained by varying the number of fitted input points and Padé coefficients independently. The suggested approach is then applied to several test cases, including Sm and Pr atomic self-energies, the Green's functions of the Hubbard model for a Bethe lattice and of the Haldane model for a nanoribbon, as well as two special test functions. The sensitivity to numerical noise and the dependence on the precision of the numerical libraries are analyzed in detail. The present approach is compared to a number of other techniques, i.e., the nonnegative least-squares method, the nonnegative Tikhonov method, and the maximum entropy method, and is shown to perform well for the chosen test cases. This conclusion holds even when the noise on the input data is increased to reach values typical for quantum Monte Carlo simulations. The ability of the algorithm to resolve fine structures is finally illustrated for two relevant test functions.

  18. Optimal Padding for the Two-Dimensional Fast Fourier Transform

    NASA Technical Reports Server (NTRS)

    Dean, Bruce H.; Aronstein, David L.; Smith, Jeffrey S.

    2011-01-01

    One-dimensional Fast Fourier Transform (FFT) operations work fastest on grids whose size is divisible by a power of two. Because of this, padding grids (that are not already sized to a power of two) so that their size is the next highest power of two can speed up operations. While this works well for one-dimensional grids, it does not work well for two-dimensional grids. For a two-dimensional grid, there are certain pad sizes that work better than others. Therefore, the need exists to generalize a strategy for determining optimal pad sizes. There are three steps in the FFT algorithm. The first is to perform a one-dimensional transform on each row in the grid. The second step is to transpose the resulting matrix. The third step is to perform a one-dimensional transform on each row in the resulting grid. Steps one and three both benefit from padding the row to the next highest power of two, but the second step needs a novel approach. An algorithm was developed that struck a balance between optimizing the grid pad size with prime factors that are small (which are optimal for one-dimensional operations), and with prime factors that are large (which are optimal for two-dimensional operations). This algorithm optimizes based on average run times, and is not fine-tuned for any specific application. It increases the amount of times that processor-requested data is found in the set-associative processor cache. Cache retrievals are 4-10 times faster than conventional memory retrievals. The tested implementation of the algorithm resulted in faster execution times on all platforms tested, but with varying sized grids. This is because various computer architectures process commands differently. The test grid was 512 512. Using a 540 540 grid on a Pentium V processor, the code ran 30 percent faster. On a PowerPC, a 256x256 grid worked best. A Core2Duo computer preferred either a 1040x1040 (15 percent faster) or a 1008x1008 (30 percent faster) grid. There are many industries that

  19. Chemical mechanical planarization of amorphous Ge2Sb2Te5 with a soft pad

    NASA Astrophysics Data System (ADS)

    Aodong, He; Bo, Liu; Zhitang, Song; Yegang, Lü; Juntao, Li; Weili, Liu; Songlin, Feng; Guanping, Wu

    2013-07-01

    Chemical mechanical planarization (CMP) of amorphous Ge2Sb2Te5 (a-GST) is investigated using two typical soft pads (politex REG and AT) in acidic slurry. After CMP, it is found that the removal rate (RR) of a-GST increases with an increase of runs number for both pads. However, it achieves the higher RR and better surface quality of a-GST for an AT pad. The in-situ sheet resistance (Rs) measure shows the higher Rs of a-GST polishing can be gained after CMP using both pads and the high Rs is beneficial to lower the reset current for the PCM cells. In order to find the root cause of the different RR of a-GST polishing with different pads, the surface morphology and characteristics of both new and used pads are analyzed, it shows that the AT pad has smaller porosity size and more pore counts than that of the REG pad, and thus the AT pad can transport more fresh slurry to the reaction interface between the pad and a-GST, which results in the high RR of a-GST due to enhanced chemical reaction.

  20. A Scott bench with ergonomic thorax stabilisation pad improves body posture during preacher arm curl exercise.

    PubMed

    Biscarini, Andrea; Benvenuti, Paolo; Busti, Daniele; Zanuso, Silvano

    2016-05-01

    We assessed whether the use of an ergonomic thorax stabilisation pad, during the preacher arm curl exercise, could significantly reduce the excessive shoulder protraction and thoracic kyphosis induced by the standard flat pad built into the existing preacher arm curl equipment. A 3D motion capture system and inclinometers were used to measure shoulder protraction and thoracic kyphosis in 15 subjects performing preacher arm curl with a plate-loaded machine provided with the standard flat pad. The same measures were repeated after replacing the flat pad with a new ergonomic pad, specifically designed to accommodate the thorax profile and improve body posture. Pad replacement significantly (p < 0.001) reduced shoulder protraction (from [Formula: see text] to [Formula: see text]) and thoracic kyphosis (from [Formula: see text] to [Formula: see text]), enabling postural and functional improvements within the entire spine, shoulder girdle and rib cage. The ergonomic pad may potentially allow a more effective training, prevent musculoskeletal discomfort and reduce the risk of injury. Practitioner summary: We have designed an ergonomic thorax stabilisation pad for the preacher arm curl exercise. The new ergonomic pad improves the poor posture conditions induced by the standard flat pad and may potentially allow a more effective training, prevent musculoskeletal discomfort, improve the breathing function and reduce the risk of injury. PMID:26226165

  1. Sequential activation of multiple grounding pads reduces skin heating during radiofrequency tumor ablation

    PubMed Central

    HAEMMERICH, DIETER; SCHUTT, DAVID JAMES

    2009-01-01

    Purpose Radiofrequency (RF) tumor ablation has become an accepted treatment modality for tumors not amenable to surgery. Skin burns due to ground pad heating may become a limiting factor for further increase in ablation zone dimensions and generator power. We investigated a method were groups of ground pads are sequentially activated to reduce skin heating. Methods We compared conventional operation (i.e. simultaneous connection of all pads) to sequentially switched activation of the pads where different pad combinations are active for periods of ∼0.3 − 8 s. The timing during sequential activation was adjusted to keep the leading edge temperature equal between the pads. We created Finite Element Method computer models of three pads (5 × 5 cm, 1 cm apart) placed in line with the RF electrode on a human thigh to determine differences in tissue heating during simultaneous and sequential ground pad activation. We performed experiments with three ground pads (5 × 10 cm, 4 cm apart) placed on a tissue phantom (1.5 A, 12 min) and measured pad surface and leading edge temperatures. Results Temperature rise below the leading edge for proximal, middle and distal ground pad in relation to active electrode location was 5.9°C ± 0.1°C, 0.8°C ± 0.1°C and 0.3°C ± 0.1°C for conventional operation, and 3.3°C ± 0.1°C, 3.4°C ± 0.2°C and 3.4°C ± 0.2°C for sequentially activated operation in the experiments (p < 0.001). Conclusion Sequential activation of multiple ground pads resulted in reduced maximum tissue temperature. This may reduce the incidence of ground pad burns and may allow higher power RF generators. PMID:18038286

  2. The FE simulation research on roll bending process of complex sheet with padding assisted

    NASA Astrophysics Data System (ADS)

    Wei, Tianhai; Zhao, Yixi; Song, Bo; Chen, Baoguo; Yu, Zhongqi

    2013-05-01

    The roll bending process with padding assisted is a new profile forming method. In this paper, the aluminum sheet 2024-T3 with variable thickness is roll bended through three-roller with padding assisted. The finite element model is established with ABAQUS software, the forming process and springback are successfully simulated. The padding material and the padding thickness are discussed based on FE model. The result showed that the PA6-G, with a higher strength, is a preferred padding material. The good forming result will be obtained if the padding of thicker thickness is chosen among 6mm and 9mm. This research provides some useful references for the real forming process of complex sheet.

  3. The effects of isolation on the mechanics of the human heel pad.

    PubMed

    Aerts, P; Ker, R F; de Clercq, D; Ilsley, D W

    1996-04-01

    In previous studies on the mechanical properties of the human heel pad (Bennett & Ker, 1990; Aerts et al. 1995) the fat pad and part of the calcaneus was removed from amputated test specimens. The present study tested whether this procedure influences the mechanical behaviour of the sample. Intact amputated feet were therefore mounted on steel rods driven through the calcaneus and placed in a mechanical test situation (pendulum or servohydraulic material tester). The mechanical properties of the pad were determined for a series of experiments in which the pad was gradually freed from the foot in the way done by Bennett & Ker (1990) and Aerts et al. (1995). The results showed no observable differences in the mechanics of the pad by isolating it from the rest of the foot. Thus, in relation to human locomotion, the load-deformation relation of heel pads as described by Aerts et al. (1995) is the most appropriate to date. PMID:8621341

  4. Bioluminescent bioreporter pad biosensor for monitoring water toxicity.

    PubMed

    Axelrod, Tim; Eltzov, Evgeni; Marks, Robert S

    2016-03-01

    Toxicants in water sources are of concern. We developed a tool that is affordable and easy-to-use for monitoring toxicity in water. It is a biosensor composed of disposable bioreporter pads (calcium alginate matrix with immobilized bacteria) and a non-disposable CMOS photodetector. Various parameters to enhance the sensor's signal have been tested, including the effect of alginate and bacterium concentrations. The effect of various toxicants, as well as, environmental samples were tested by evaluating their effect on bacterial luminescence. This is the first step in the creation of a sensitive and simple operative tool that may be used in different environments. PMID:26717844

  5. STS-101 Atlantis at Launch Pad 39-A after rollout

    NASA Technical Reports Server (NTRS)

    2000-01-01

    Space Shuttle Atlantis, atop the mobile launcher platform and crawler-transporter, sits on launch Pad 39A with the Atlantic Ocean in the background after having traveled 3.4 miles from the Vehicle Assembly Building. Liftoff of Atlantis on mission STS-101 is scheduled for April 17 at 7:03 p.m. EDT. STS-101 is a logistics and resupply mission for the International Space Station, to restore full redundancy to the International Space Station power system in preparation for the arrival of the next pressurized module, the Russian-built Zvezda.

  6. Secure direct communication with a quantum one-time pad

    SciTech Connect

    Deng Fuguo; Long Guilu

    2004-05-01

    Quantum secure direct communication is the direct communication of secret messages without first producing a shared secret key. It may be used in some urgent circumstances. Here we propose a quantum secure direct communication protocol using single photons. The protocol uses batches of single photons prepared randomly in one of four different states. These single photons serve as a one-time pad which is used directly to encode the secret messages in one communication process. We also show that it is unconditionally secure. The protocol is feasible with present-day technique.

  7. STS-107 Columbia rollout to Launch Pad 39A

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- Space Shuttle Columbia, framed by trees near the Banana River, rolls towards Launch Pad 39A, sitting atop the Mobile Launcher Platform, which in turn is carried by the crawler-transporter underneath. The STS-107 research mission comprises experiments ranging from material sciences to life sciences (many rats), plus the Fast Reaction Experiments Enabling Science, Technology, Applications and Research (FREESTAR) that incorporates eight high priority secondary attached shuttle experiments. Mission STS-107 is scheduled to launch Jan. 16, 2003.

  8. Analysis of Compression Pad Cavities for the Orion Heatshield

    NASA Technical Reports Server (NTRS)

    Thompson, Richard A.; Lessard, Victor R.; Jentink, Thomas N.; Zoby, Ernest V.

    2009-01-01

    Current results of a program for analysis of the compression pad cavities on the Orion heatshield are reviewed. The program was supported by experimental tests, engineering modeling, and applied computations with an emphasis on the latter presented in this paper. The computational tools and approach are described along with calculated results for wind tunnel and flight conditions. Correlations of the computed results are shown which can produce a credible prediction of heating augmentation due to cavity disturbances. The models developed for use in preliminary design of the Orion heatshield are presented.

  9. New fertilizer-producing system installed at Pad 39A

    NASA Technical Reports Server (NTRS)

    2000-01-01

    A recently installed fertilizer-producing system sits near Launch Pad 39A. Using a 'scrubber,' the system captures nitrogen tetroxide vapor that develops as a by-product when it is transferred from ground storage tanks into the Shuttle storage tanks. Nitrogen tetroxide is used as the oxidizer for the hypergolic propellant in the Shuttle's on-orbit reaction control system. The scrubber then uses hydrogen peroxide to produce nitric acid, which, after adding potassium hydroxide, converts to potassium nitrate, a commercial fertilizer. Plans call for the resulting fertilizer to be used on the orange groves that KSC leases to outside companies.

  10. STS-89 Endeavour at Pad 39-A after rollout

    NASA Technical Reports Server (NTRS)

    1997-01-01

    The Space Shuttle Endeavour rolls out to Launch Pad 39A, the destination of its 3.4-mile journey from the Vehicle Assembly Building, for final preparations for liftoff of the STS-89 mission. Endeavour and its crew of seven are targeted for a Jan. 22 launch. STS-89 will be the eighth Shuttle docking with the Russian Space Station Mir as part of Phase 1 of the International Space Station program. Mission Specialist Andy Thomas, Ph.D., will succeed Mission Specialist David Wolf, M.D., as the last NASA astronaut scheduled for a long-duration stay aboard Mir.

  11. STS-98 Atlantis begins rolling to Launch Pad 39A

    NASA Technical Reports Server (NTRS)

    2001-01-01

    KENNEDY SPACE CENTER, Fla. -- Space Shuttle Atlantis moves through the doors of the Vehicle Assembly Building on its rollout to Launch Pad 39A. Atlantis will fly on mission STS-98, the seventh construction flight to the International Space Station. The orbiter will carry in its payload bay the U.S. Laboratory, named Destiny, that will have five system racks already installed inside the module. After delivery of electronics in the lab, electrically powered attitude control for Control Moment Gyroscopes will be activated. Atlantis is scheduled for launch no earlier than Jan. 19, 2001, with a crew of five.

  12. Operating characteristics of a cantilever-mounted resilient-pad gas-lubricated thrust bearing

    NASA Technical Reports Server (NTRS)

    Nemeth, Z. N.

    1979-01-01

    A resilient-pad gas thrust bearing consisting of pads mounted on cantilever beams was tested to determine its operating characteristic. The bearing was run at a thrust load of 74 newtons to a speed of 17000 rpm. The pad film thickness and bearing friction torque were measured and compared with theory. The measured film thickness was less than that predicted by theory. The bearing friction torque was greater than that predicted by theory.

  13. Accessibility: The Top 10 iPad Apps for Special Education

    ERIC Educational Resources Information Center

    Palmer, Randall

    2013-01-01

    The iPad takeover of public education is not just confined to the mainstream classroom: Special needs educators, too, are finding that iPads can be a vital tool to support independence. What sets the iPad apart from other devices is the simple and visually robust user interface that can be used by almost everyone. It is also a highly customizable…

  14. "I Have an iPad. Now What?" Using Mobile Devices in University Physical Education Programs

    ERIC Educational Resources Information Center

    Rosenthal, Maura B.; Eliason, Susan K.

    2015-01-01

    In response to an iPad initiative at a mid-sized New England university, all faculty, junior and senior undergraduates, and graduate students were required to have iPads by the first day of class in the fall semester of 2013. Goals of the initiative focused on preparing future teachers to use the iPad as a teaching and learning tool so they could…

  15. Measuring emissions from oil and natural gas well pads using the mobile flux plane technique.

    PubMed

    Rella, Chris W; Tsai, Tracy R; Botkin, Connor G; Crosson, Eric R; Steele, David

    2015-04-01

    We present a study of methane emissions from oil and gas producing well pad facilities in the Barnett Shale region of Texas, measured using an innovative ground-based mobile flux plane (MFP) measurement system, as part of the Barnett Coordinated Campaign.1 Using only public roads, we measured the emissions from nearly 200 well pads over 2 weeks in October 2013. The population of measured well pads is split into well pads with detectable emissions (N = 115) and those with emissions below the detection limit of the MFP instrument (N = 67). For those well pads with nonzero emissions, the distribution was highly skewed, with a geometric mean of 0.63 kg/h, a geometric standard deviation of 4.2, and an arithmetic mean of 1.72 kg/h. Including the population of nonemitting well pads, we find that the arithmetic mean of the well pads sampled in this study is 1.1 kg/h. This distribution implies that 50% of the emissions is due to the 6.6% highest emitting well pads, and 80% of the emissions is from the 22% highest emitting well pads. PMID:25806837

  16. Analysis of the gas-lubricated flat-sector-pad thrust bearing

    NASA Technical Reports Server (NTRS)

    Etsion, I.

    1976-01-01

    A flat sector-shaped pad geometry for a gas-lubricated thrust bearing is analyzed considering both the pitch and roll of the pad. It is shown that maximum load capacity is achieved when the pad is tilted so as to create uniform minimum film thickness along the pad trailing edge. Performance characteristics for various geometries and operating conditions of gas thrust bearings are presented in the form of design curves, and a comparison is made with the rectangular slider approximation. It is found that this approximation is unsafe for practical design, since it always overestimates load capacity.

  17. Deep Space 1 is prepared for transport to launch pad

    NASA Technical Reports Server (NTRS)

    1998-01-01

    In the Defense Satellite Communications Systems Processing Facility (DPF), Cape Canaveral Air Station (CCAS), after covering the lower portion of Deep Space 1, workers adjust the anti-static blanket covering the upper portion. The blanket will protect the spacecraft during transport to the launch pad. Deep Space 1 is the first flight in NASA's New Millennium Program, and is designed to validate 12 new technologies for scientific space missions of the next century, including the engine. Propelled by the gas xenon, the engine is being flight-tested for future deep space and Earth-orbiting missions. Deceptively powerful, the ion drive emits only an eerie blue glow as ionized atoms of xenon are pushed out of the engine. While slow to pick up speed, over the long haul it can deliver 10 times as much thrust per pound of fuel as liquid or solid fuel rockets. Other onboard experiments include software that tracks celestial bodies so the spacecraft can make its own navigation decisions without the intervention of ground controllers. Deep Space 1 will complete most of its mission objectives within the first two months, but will also do a flyby of a near-Earth asteroid, 1992 KD, in July 1999. Deep Space 1 will be launched aboard a Boeing Delta 7326 rocket from Launch Pad 17A, CCAS.

  18. Deep Space 1 is prepared for transport to launch pad

    NASA Technical Reports Server (NTRS)

    1998-01-01

    In the Defense Satellite Communications Systems Processing Facility (DPF), Cape Canaveral Air Station (CCAS), workers place an anti-static blanket over the lower portion of Deep Space 1, to protect the spacecraft during transport to the launch pad. The first flight in NASA's New Millennium Program, Deep Space 1 is designed to validate 12 new technologies for scientific space missions of the next century, including the engine. Propelled by the gas xenon, the engine is being flight-tested for future deep space and Earth-orbiting missions. Deceptively powerful, the ion drive emits only an eerie blue glow as ionized atoms of xenon are pushed out of the engine. While slow to pick up speed, over the long haul it can deliver 10 times as much thrust per pound of fuel as liquid or solid fuel rockets. Other onboard experiments include software that tracks celestial bodies so the spacecraft can make its own navigation decisions without the intervention of ground controllers. Deep Space 1 will complete most of its mission objectives within the first two months, but will also do a flyby of a near-Earth asteroid, 1992 KD, in July 1999. Deep Space 1 will be launched aboard a Boeing Delta 7326 rocket from Launch Pad 17A, CCAS.

  19. Plutonium release from the 903 pad at Rocky Flats.

    PubMed

    Mongan, T R; Ripple, S R; Winges, K D

    1996-10-01

    The Colorado Department of Public Health and Environment (CDH) sponsored a study to reconstruct contaminant doses to the public from operations at the Rocky Flats nuclear weapons plant. This analysis of the accidental release of plutonium from the area known as the 903 Pad is part of the CDH study. In the 1950's and 1960's, 55-gallon drums of waste oil contaminated with plutonium, and uranium were stored outdoors at the 903 Pad. The drums corroded, leaking contaminated oil onto soil subsequently carried off-site by the wind. The plutonium release is estimated using environmental data from the 1960's and 1970's and an atmospheric transport model for fugitive dust. The best estimate of total plutonium release to areas beyond plant-owned property is about 0.26 TBq (7 Ci). Off-site airborne concentrations and deposition of plutonium are estimated for dose calculation purposes. The best estimate of the highest predicted off-site effective dose is approximately 72 microSv (7.2 mrem). PMID:8830753

  20. Lateral pharyngeal fat pad pressure during breathing in anesthetized pigs.

    PubMed

    Winter, W C; Gampper, T; Gay, S B; Suratt, P M

    1997-09-01

    It has been hypothesized that the pressure in tissues surrounding the upper airway is one of the determinants of the size and shape of the upper airway. To our knowledge, this pressure has not been measured. The purpose of this study was to test whether the pressure in a tissue lateral to the upper airway, the lateral pharyngeal fat pad pressure (Pfp), differs from atmospheric and pharyngeal pressures and whether it changes with breathing. We studied six male lightly sedated pigs by inserting a transducer tipped catheter into their fat pad space by using computerized tomographic scan guidance. We measured airflow with a pneumotachograph attached to a face mask and pharyngeal pressure with a balloon catheter. Pfp differed from atmospheric pressure, generally exceeding it, and from pharyngeal pressure. Pfp correlated positively with airflow and with pharyngeal pressure, decreasing during inspiration and increasing during expiration. Changes in Pfp with ventilation were eliminated by oropharyngeal intubation. We conclude that Pfp differs from atmospheric and pharyngeal pressures and that it changes with breathing. PMID:9292450

  1. STS-101 Atlantis on the pad after RSS rollback

    NASA Technical Reports Server (NTRS)

    2000-01-01

    After rollback of the Rotating Service Structure at Launch Pad 39A, Space Shuttle Atlantis awaits a fourth launch attempt on mission STS-101. At the top of the orange external tank can be seen the Gaseous Oxygen Vent Hood, often called the 'beanie cap.' The hood helps vent gaseous oxygen vapors away from the Space Shuttle. The hood will be raised and retracted two and a half minutes before launch. Abutting the side of Atlantis is the orbiter access arm with the environmental chamber known as the White Room at the end. The White Room provides access to the crew compartment. This will be the third assembly flight to the International Space Station. Liftoff of Space Shuttle Atlantis for the 10-day mission is scheduled for about 6:12 a.m. EDT from Launch Pad 39A. Landing is targeted for May 29 at 2:19 a.m. EDT. This is the 98th Shuttle flight and the 21st flight for Shuttle Atlantis.

  2. Thermal Neutron Detectors with Discrete Anode Pad Readout

    SciTech Connect

    Yu,B.; Schaknowski, N.A., Smith, G.C., DeGeronimo, G., Vernon, E.O.

    2008-10-19

    A new two-dimensional thermal neutron detector concept that is capable of very high rates is being developed. It is based on neutron conversion in {sup 3}He in an ionization chamber (unity gas gain) that uses only a cathode and anode plane; there is no additional electrode such as a Frisch grid. The cathode is simply the entrance window, and the anode plane is composed of discrete pads, each with their own readout electronics implemented via application specific integrated circuits. The aim is to provide a new generation of detectors with key characteristics that are superior to existing techniques, such as higher count rate capability, better stability, lower sensitivity to background radiation, and more flexible geometries. Such capabilities will improve the performance of neutron scattering instruments at major neutron user facilities. In this paper, we report on progress with the development of a prototype device that has 48 x 48 anode pads and a sensitive area of 24cm x 24cm.

  3. Perceptions and Use of iPad Technology by Pharmacy Practice Faculty Members

    PubMed Central

    Zgarrick, David P.

    2014-01-01

    Objectives. To explore the potential of tablet technology to address the specific workload challenges of pharmacy practice faculty members and to evaluate tablet usage after a department-wide iPad initiative. Methods. After conducting a needs assessment to determine pharmacy faculty attitudes towards tablet technology and to identify potential usage scenarios, all faculty members in a department of pharmacy practice received an iPad. After iPad distribution, training sessions and virtual tutorials were provided. An anonymous survey was administered to evaluate the pilot. Results. The needs assessment survey revealed positive attitudes towards iPad technology, identified use scenarios, and led to a department-wide iPad pilot program. Most faculty members used iPads for connectivity with students (86%), paper/project annotation (68%), assessment (57%), and demonstration of tools used in practice (36%). For teaching, 61% of faculty members used iPads in seminars/laboratories, 57% used iPads in the experiential setting, and 43% used iPads in the classroom. Use of iPads for patient-care activities varied and depended on site support for mobile technology. The 23 faculty members with external practice sites used iPads to a greater extent and had more positive attitudes towards this technology compared with campus-based faculty members. Conclusion. Integration of tablet technology into the pharmacy education setting resulted in faculty-reported increased productivity and decreased paper waste. It also allowed faculty members to experiment with new teaching strategies in the classroom and experiential setting. Administrators at institutions exploring the use of tablet technology should allocate resources based on faculty needs and usage patterns. PMID:24761013

  4. iPad[TM]: Enhancing Learning & Communication for Students with Special Needs

    ERIC Educational Resources Information Center

    Friedlander, Brian; Besko-Maughan, Christine

    2011-01-01

    The iPad[TM] is a revolutionary technology for use in our 21st century classrooms. It is profoundly changing both the manner in which teachers present instructional content, as well as the way students process and learn new information. The multi-sensory design of the iPad[TM] makes it an ideal tool for teaching students with special needs. This…

  5. How and Why Academics Do and Do Not Use iPads for Academic Teaching?

    ERIC Educational Resources Information Center

    Aiyegbayo, Olaojo

    2015-01-01

    This paper evaluated how academics, at a mid-sized UK university, used their iPads for teaching. The data were gathered using both quantitative and qualitative methods. Eighty-four academics completed a survey while 22 semi-structured interviews were conducted. Eleven interviewees reported that they used their iPads for teaching purposes and the…

  6. Evaluating iPad Technology for Enhancing Communication Skills of Children with Autism Spectrum Disorders

    ERIC Educational Resources Information Center

    Boyd, Tara K.; Hart Barnett, Juliet E.; More, Cori M.

    2015-01-01

    Mobile technology has introduced a new communication opportunity for students with autism spectrum disorder. Tablets, like the iPad, allow users to customize applications for their needs. Users also have found iPads to be less stigmatizing because so many people own them and use them for various purposes. In the fast-paced world of technology,…

  7. Digital Course Materials: A Case Study of the Apple iPad in the Academic Environment

    ERIC Educational Resources Information Center

    Cameron, Andrea H.; Bush, Michael H.

    2011-01-01

    The newness of the iPad device creates a phenomenon unique and unstudied in the academic environment. By merging the innovations of electronic text, e-reader, and multi-modal functionality, the iPad tablet device can act as an e-reader providing digital course materials as well as a range of other supplementary academic applications. This…

  8. 77 FR 40527 - New Express Mail Price Category-Express Mail Padded Flat Rate Envelope

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-07-10

    ... 111 New Express Mail Price Category--Express Mail Padded Flat Rate Envelope AGENCY: Postal Service TM... a new price category under Express Mail, Express Mail Padded Flat Rate Envelope, established by the Governors of the United States Postal Service . The new price category is available under Docket...

  9. MSA-PAD: DNA multiple sequence alignment framework based on PFAM accessed domain information.

    PubMed

    Balech, Bachir; Vicario, Saverio; Donvito, Giacinto; Monaco, Alfonso; Notarangelo, Pasquale; Pesole, Graziano

    2015-08-01

    Here we present the MSA-PAD application, a DNA multiple sequence alignment framework that uses PFAM protein domain information to align DNA sequences encoding either single or multiple protein domains. MSA-PAD has two alignment options: gene and genome mode. PMID:25819080

  10. Impact response of US Army and National Football League helmet pad systems

    SciTech Connect

    Moss, W C; King, M J

    2011-02-18

    Lawrence Livermore National Laboratory [LLNL] was tasked to compare the impact response of NFL helmet pad systems and U.S. Army pad systems compatible with an Advanced Combat Helmet [ACH] at impact velocities up to 20 ft/s. This was a one-year study funded by the U.S. Army and JIEDDO. The Army/JIEDDO point of contact is COL R. Todd Dombroski, DO, JIEDDO Surgeon. LLNL was chosen by committee to perform the research based on prior published computational studies of the mechanical response of helmets and skulls to blast. Our collaborators include the U.S. Army Aeromedical Research Laboratory [USAARL] (a DoD laboratory responsible for impact testing helmets), Team Wendy and Oregon Aero (current and former ACH pad manufacturers), Riddell and Xenith (NFL pad manufacturers), and d3o (general purpose sports pad manufacturer). The manufacturer-supplied pad systems that were studied are shown in the figure below. The first two are the Army systems, which are bilayer foam pads with both hard and soft foam and a water-resistant airtight wrapper (Team Wendy) or a water-resistant airtight coating (Oregon Aero). The next two are NFL pad systems. The Xenith system consists of a thin foam pad and a hollow air-filled cylinder that elastically buckles under load. The Riddell system is a bilayer foam pad that is encased in an inflatable airbag with relief channels to neighboring pads in the helmet. The inflatable airbag is for comfort and provides no enhancement to impact mitigation. The d3o system consists of a rate-sensitive homogeneous dense foam. LLNL performed experiments to characterize the material properties of the individual foam materials and the response of the complete pad systems, to obtain parameters needed for the simulations. LLNL also performed X-ray CT scans of an ACH helmet shell that were used to construct a geometrically accurate computational model of the helmet. Two complementary sets of simulations were performed. The first set of simulations reproduced the

  11. Influence of usage practices, ethnicity and climate on the skin compatibility of sanitary pads.

    PubMed

    Farage, Miranda; Elsner, Peter; Maibach, Howard

    2007-06-01

    Modern disposable sanitary pads are becoming available worldwide. Regional differences in usage practices, ethnicity, and climate may influence their skin compatibility. Pad usage practices depend on culture, economics, and menstrual physiology. Daily usage is higher in Japan and but lower in Nigeria compared to North America or Western Europe. Evidence for ethnic differences in skin irritant susceptibility is not compelling. Dark skin may be less susceptible to certain irritants than fair skin; the Japanese may experience a higher degree of sensory irritation than Caucasians. Ambient conditions such as high temperature and humidity increase the skin temperature and skin surface moisture under sanitary pads by small but measurable amounts, causing no discernible skin irritation; vapor-permeable pad backings reduce these effects. Cold dry conditions, which can irritate exposed skin, may not affect vulvar skin to the same degree due to its elevated hydration and occlusion. To address the practical significance of these variables, results of prospective clinical trials of sanitary pads performed by industry and academic scientists in North America (Indiana), Mexico, Western Europe (Munich, Athens, Goteborg, Sweden), Eastern Europe (Kiev) and Africa (Abuja, Nigeria) were reviewed. Despite the diverse range of conditions, no significant adverse skin effects were observed with modern pads compared to traditional pad designs. Study participants generally preferred modern pads for performance and comfort. PMID:17514373

  12. STS-30 Atlantis, OV-104, on the mobile launcher platform heads to KSC LC pad

    NASA Technical Reports Server (NTRS)

    1989-01-01

    STS-30 Atlantis, Orbiter Vehicle (OV) 104, riding atop the mobile launcher platform and the crawler transporter approaches Kennedy Space Center (KSC) Launch Complex (LC) pad 39B. This backlit view highlights OV-104's profile, the external tank (ET), and one of the two solid rocket boosters (SRBs) as it moves up LC pad 39B incline.

  13. Engaging Organic Chemistry Students Using ChemDraw for iPad

    ERIC Educational Resources Information Center

    Morsch, Layne A.; Lewis, Michael

    2015-01-01

    Drawing structures, mechanisms, and syntheses is a vital part of success in organic chemistry courses. ChemDraw for iPad has been used to increase classroom experiences in the preparation of high quality chemical drawings. The embedded Flick-to-Share allows for simple, real-time exchange of ChemDraw documents. ChemDraw for iPad also allows…

  14. 49 CFR 393.47 - Brake actuators, slack adjusters, linings/pads and drums/rotors.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... drums/rotors. 393.47 Section 393.47 Transportation Other Regulations Relating to Transportation..., slack adjusters, linings/pads and drums/rotors. (a) General requirements. Brake components must be... shoe with two pads; or worn to the wear indicator if the lining is so marked, for air drum brakes....

  15. 49 CFR 393.47 - Brake actuators, slack adjusters, linings/pads and drums/rotors.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... drums/rotors. 393.47 Section 393.47 Transportation Other Regulations Relating to Transportation..., slack adjusters, linings/pads and drums/rotors. (a) General requirements. Brake components must be... shoe with two pads; or worn to the wear indicator if the lining is so marked, for air drum brakes....

  16. 49 CFR 393.47 - Brake actuators, slack adjusters, linings/pads and drums/rotors.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... drums/rotors. 393.47 Section 393.47 Transportation Other Regulations Relating to Transportation..., slack adjusters, linings/pads and drums/rotors. (a) General requirements. Brake components must be... shoe with two pads; or worn to the wear indicator if the lining is so marked, for air drum brakes....

  17. 49 CFR 393.47 - Brake actuators, slack adjusters, linings/pads and drums/rotors.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... drums/rotors. 393.47 Section 393.47 Transportation Other Regulations Relating to Transportation..., slack adjusters, linings/pads and drums/rotors. (a) General requirements. Brake components must be... shoe with two pads; or worn to the wear indicator if the lining is so marked, for air drum brakes....

  18. 49 CFR 393.47 - Brake actuators, slack adjusters, linings/pads and drums/rotors.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... drums/rotors. 393.47 Section 393.47 Transportation Other Regulations Relating to Transportation..., slack adjusters, linings/pads and drums/rotors. (a) General requirements. Brake components must be... shoe with two pads; or worn to the wear indicator if the lining is so marked, for air drum brakes....

  19. Using iPads as a Data Collection Tool in Extension Programming Evaluation

    ERIC Educational Resources Information Center

    Rowntree, J. E.; Witman, R. R.; Lindquist, G. L.; Raven, M. R.

    2013-01-01

    Program evaluation is an important part of Extension, especially with the increased emphasis on metrics and accountability. Agents are often the point persons for evaluation data collection, and Web-based surveys are a commonly used tool. The iPad tablet with Internet access has the potential to be an effective survey tool. iPads were field tested…

  20. A&M. Jet engine test pad and control building (TAN609). Camera ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    A&M. Jet engine test pad and control building (TAN-609). Camera facing westerly. Engine pad at left, control section (pumice block) on right. Date: September 19, 1955. INEEL negative no. 55-2766 - Idaho National Engineering Laboratory, Test Area North, Scoville, Butte County, ID

  1. Orion Pad Abort 1 Flight Test: Simulation Predictions Versus Flight Data

    NASA Technical Reports Server (NTRS)

    Stillwater, Ryan Allanque; Merritt, Deborah S.

    2011-01-01

    The presentation covers the pre-flight simulation predictions of the Orion Pad Abort 1. The pre-flight simulation predictions are compared to the Orion Pad Abort 1 flight test data. Finally the flight test data is compared to the updated simulation predictions, which show a ove rall improvement in the accuracy of the simulation predictions.

  2. Sharing Personalised Stories on iPads: A Close Look at One Parent-Child Interaction

    ERIC Educational Resources Information Center

    Kucirkova, Natalia; Messer, David; Sheehy, Kieron; Flewitt, Rosie

    2013-01-01

    Little is known about how specific iPad applications affect parent-child story-sharing interactions. This study utilises a case-study approach to provide an insight into the patterns of interaction, which emerge when a mother and her 33-month-old daughter share a self-created, audio-visual "iPad story". Multimodal analysis allowed us to…

  3. Free tissue transfer of digital food pads for reconstruction of the distal limb in the dog.

    PubMed

    Basher, A W; Fowler, J D; Bowen, C V

    1991-01-01

    Reconstructive procedures used in salvaging distal limb injuries in the dog are reviewed. Techniques employed to resurface the distal weight-bearing surface include local reconstruction using pedicle flap transposition of foot pads. The development of a previously described free microneurovascular digital foot pad flap is reviewed; the experimental results and potential for clinical use of the free flap are discussed. PMID:1672726

  4. Patient Positioning and Skin Sequelae: Ischemic Epidermal Necrosis from Tight Padding During Cardiac Surgery.

    PubMed

    Sadeghpour, Mona; Au, Jeremiah; Ho, Jonhan; Hyman, Jaime; Patton, Timothy

    2016-05-15

    Careful positioning and padding of pressure points during surgery are recommended to prevent pressure ulcers, vascular injury, and nerve damage in an immobilized patient. However, overpadding may have unintended consequences. We report a case of ischemia-induced full-thickness epidermal necrosis secondary to tight foam padding during a cardiac surgery. PMID:26934606

  5. Another Perspective: The iPad Is a REAL Musical Instrument

    ERIC Educational Resources Information Center

    Williams, David A.

    2014-01-01

    This article looks at the iPad's role as a musical instrument through the lens of a live performance ensemble that performs primarily on iPads. It also offers an overview of a pedagogical model used by this ensemble, which emphasizes musician autonomy in small groups, where music is learned primarily through aural means and concerts are…

  6. Experimental evaluation of foil-supported resilient-pad gas-lubricated thrust bearing

    NASA Technical Reports Server (NTRS)

    Nemeth, Z. N.

    1977-01-01

    A new type of resilient-pad gas thrust bearing was tested to determine the feasibility of the design. The bearing consists of carbon graphite pads mounted asymmetrically on foil beams. Two bearing configurations were tested at thrust loads from 27 to 80 newtons at speeds to 9000 rpm. The outside diameter of the bearing was 8.9 centimeters.

  7. 77 FR 42713 - Notice of Intent to Grant an Exclusive License; PadJack, Inc.

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-07-20

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF DEFENSE Office of the Secretary Notice of Intent to Grant an Exclusive License; PadJack, Inc. AGENCY: National... intent to grant PadJack, Inc. a revocable exclusive license to practice the following...

  8. The Tablet Inscribed: Inclusive Writing Instruction with the iPad

    ERIC Educational Resources Information Center

    Sullivan, Rebecca M.

    2013-01-01

    Despite the author's initial skepticism, a classroom set of iPads has reinforced a student-directed approach to writing instruction, while also supporting an inclusive classroom. Using the iPads, students guide their writing process with access to the learning management system, electronic information resources, and an online text editor. Students…

  9. A Phenomenographic Investigation on the Use of iPads among Undergraduate Art and Design Students

    ERIC Educational Resources Information Center

    Souleles, Nicos; Savva, Stefania; Watters, Hilary; Annesley, Angela; Bull, Ben

    2015-01-01

    The increasingly widespread use of iPads in higher education (HE) brings to the forefront questions about the contribution of these computer tablets towards teaching and learning. However, there is a noticeable gap of research on the instructional potential of iPads in HE. This paper describes the first stage of a research project on the use of…

  10. Student Perceptions of iPads as Mobile Learning Devices for Fieldwork

    ERIC Educational Resources Information Center

    Welsh, Katharine E.; Mauchline, Alice L.; Powell, Victoria; France, Derek; Park, Julian R.; Whalley, W. Brian

    2015-01-01

    This paper reports findings from six field courses about student's perceptions of iPads as mobile learning devices for fieldwork. Data were collected through surveys and focus groups. The key findings suggest that the multi-tool nature of the iPads and their portability were the main strengths. Students had some concerns over the safety of the…

  11. Lessons from Using iPads to Understand Young Children's Creativity

    ERIC Educational Resources Information Center

    Arnott, Lorna; Grogan, Deirdre; Duncan, Pauline

    2016-01-01

    This article explores the use of iPads as part of a child-centred data collection approach to understand young children's creativity. Evidence is presented from a small study of three- to five-year-old children's creative play. Analysis of the children's engagement with iPad video diaries and free-to-use tablet applications was logged across two…

  12. Story-Making on the iPad When Children Have Complex Needs: Two Case Studies

    ERIC Educational Resources Information Center

    Kucirkova, Natalia; Messer, David; Critten, Val; Harwood, Jane

    2014-01-01

    The two case studies reported in this clinical exchange describe the way in which iPads can foster children's motivation to engage in communication and literacy-related activities such as story-sharing and story-creation. A detailed description of a particular iPad app (Our Story) is provided, along with observations of the implementation of…

  13. Examining Teachers' Use of iPads: Comfort Level, Perception, and Use

    ERIC Educational Resources Information Center

    Liu, Min; Navarrete, Cesar C.; Scordino, Robert; Kang, Jina; Ko, Yujung; Lim, Mihyun

    2016-01-01

    While there is evidence of the growing popularity of iPads and other tablets in K-12 education, little is understood about how teachers use these devices in their instruction. This study examines 342 teachers' comfort level with and perception toward iPad use and any changes that occurred over the implementation year. Using a mixed-methods design,…

  14. Professional and Parental Attitudes toward iPad Application Use in Autism Spectrum Disorder

    ERIC Educational Resources Information Center

    Clark, Megan L. E.; Austin, David W.; Craike, Melinda J.

    2015-01-01

    This study explored the attitudes of parents and professionals who work with children with autism spectrum disorder (ASD) toward the utilization of iPads and use of iPad applications by children with ASD. A survey of parents (n = 90) and professionals (n = 31) assessed information and communication technology (ICT) anxiety and self-efficacy,…

  15. iPad Use for Accelerating Reading Gains in Secondary Students with Learning Disabilities

    ERIC Educational Resources Information Center

    Retter, Shannan; Anderson, Christine; Kieran, Laura

    2013-01-01

    This action research project explored the use of the iPad 2 in a special education classroom with high school students who were considered struggling readers to determine if an academic gain in reading comprehension, reading fluency, and vocabulary implementing the intervention of an iPad and four specific applications (apps). The high school…

  16. Professional Development for iPad Integration in General Education: Staying Ahead of the Curve

    ERIC Educational Resources Information Center

    Psiropoulos, Dmitri; Barr, Sandy; Eriksson, Claire; Fletcher, Shauna; Hargis, Jace; Cavanaugh, Cathy

    2016-01-01

    This faculty development case study focuses on a team of 16 General Education faculty at an urban women's college during the initial 6 months of the college's comprehensive implementation of an iPad teaching and learning environment. This article traces the effectiveness of an iPad professional development program through analyses of critical…

  17. Exploring the Use of the iPad for Literacy Learning

    ERIC Educational Resources Information Center

    Hutchison, Amy; Beschorner, Beth; Schmidt-Crawford, Denise

    2012-01-01

    The goal of this investigation was to explore how a fourth grade teacher could integrate iPads into her literacy instruction to simultaneously teach print-based and digital literacy goals. The teacher used iPads for a three-week period during her literacy instruction and selected apps that provided unique approaches to helping the students meet…

  18. iPad Deployment in a Diverse Urban High School: A Formative Experiment

    ERIC Educational Resources Information Center

    Frey, Nancy; Fisher, Douglas; Lapp, Diane

    2015-01-01

    We explore the use of iPads in a diverse urban high school and the ways in which teachers and students were supported to integrate these tools into their instruction. We provided 4 English teachers with 20 iPads with little or no professional development about how to integrate them into their instruction. Using a formative experiment design, we…

  19. 16 CFR 300.23 - Linings, paddings, stiffening, trimmings and facings.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Linings, paddings, stiffening, trimmings and facings. (a) In labeling or marking garments or articles of... facings of such garments or articles of apparel shall be given and shall be set forth separately and..., paddings, stiffening, trimmings or facings are customarily made. (b) In the case of garments which...

  20. 16 CFR 300.23 - Linings, paddings, stiffening, trimmings and facings.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... Linings, paddings, stiffening, trimmings and facings. (a) In labeling or marking garments or articles of... facings of such garments or articles of apparel shall be given and shall be set forth separately and..., paddings, stiffening, trimmings or facings are customarily made. (b) In the case of garments which...

  1. 16 CFR 300.23 - Linings, paddings, stiffening, trimmings and facings.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... Linings, paddings, stiffening, trimmings and facings. (a) In labeling or marking garments or articles of... facings of such garments or articles of apparel shall be given and shall be set forth separately and..., paddings, stiffening, trimmings or facings are customarily made. (b) In the case of garments which...

  2. 16 CFR 300.23 - Linings, paddings, stiffening, trimmings and facings.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Linings, paddings, stiffening, trimmings and facings. (a) In labeling or marking garments or articles of... facings of such garments or articles of apparel shall be given and shall be set forth separately and..., paddings, stiffening, trimmings or facings are customarily made. (b) In the case of garments which...

  3. 16 CFR 300.23 - Linings, paddings, stiffening, trimmings and facings.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... Linings, paddings, stiffening, trimmings and facings. (a) In labeling or marking garments or articles of... facings of such garments or articles of apparel shall be given and shall be set forth separately and..., paddings, stiffening, trimmings or facings are customarily made. (b) In the case of garments which...

  4. Deterministic measurement and correction of the pad shape in full-aperture polishing processes

    NASA Astrophysics Data System (ADS)

    Liao, D.; Zhang, Q.; Xie, R.; Chen, X.; Zhao, S.; Wang, J.

    2015-11-01

    Full-aperture polishing is a significant process in fabricating large optical flats because it restrains Mid-Spatial Frequency errors and removes material quickly on the whole optic surface. Nevertheless, optical flats fabricated by full-aperture polishing generally fail to meet the stringent requirement of surface figure, which has to be corrected by sub-aperture polishing processes. Surface figure of optical flats in full-aperture polishing processes is primarily dependent on the pressure distribution uniformity which correlates intensively with the lap shape. At present, practical and precise means are urgently desired for measuring and correcting the lap shape, especially the polyurethane pad lap. In the study, we present a novel method for deterministic measurement of the pad shape. The method obtains the height of the pad at spirally distributed locations implemented by the revolution of the pad and translation of the laser displacement sensor. The pad shape in terms of matrixes whose elements representing the heights at the corresponding locations is then calculated by interpolation algorithm based on the obtained data. Further, we propose a method for deterministic correction of the pad shape utilizing a small conditioning tool. The dwell time algorithm and implementation strategy for the dwell time are provided for common full-aperture polishers. These solutions for the deterministic measurement and correction of the pad shape have been validated on a full-aperture polisher with polyurethane pad. The polishing experiments revealed that the optic surface figure was obviously improved.

  5. MANIPULATION PAD--PRELIMINARY REPORT ON A STUDENT-COMPUTER INTERFACE DEVICE FOR PROGRAMMED INSTRUCTION.

    ERIC Educational Resources Information Center

    BALL, J.R.; AND OTHERS

    AN INVESTIGATION WAS MADE OF SOME ENTIRELY NEW INPUT-OUTPUT DEVICES DESIGNED TO SOLVE SOME FUNCTIONAL AND ECONOMIC PROBLEMS THAT ARE PRESENT IN EXISTING COMPUTER-CONTROLLED INSTRUCTION EQUIPMENT. THREE FORMS OF MANIPULATION PAD WERE STUDIED. INFORMATION ABOUT SPECIALLY PREPARED OBJECTS PLACED ON THE FLAT SURFACE OF THE PAD WAS SUPPLIED TO A…

  6. GDA (Geologic Data Assistant), an ArcPad extension for geologic mapping: code, prerequisites, and instructions

    USGS Publications Warehouse

    Evan E. Thoms and Ralph A. Haugerud

    2006-01-01

    GDA (Geologic Data Assistant) is an extension to ArcPad, a mobile mapping software program by Environmental Systems Research Institute (ESRI) designed to run on personal digital assistant (PDA) computers. GDA and ArcPad allow a PDA to replace the paper notebook and field map traditionally used for geologic mapping. GDA allows easy collection of field data.

  7. The Neglected "R": Improving Writing Instruction through iPad Apps

    ERIC Educational Resources Information Center

    Sessions, Laird; Kang, Mi Ok; Womack, Sue

    2016-01-01

    In this study the authors investigated the effects of integrating iPad applications into writing instruction for fifth grade students. By comparing the writing of students taught with paper and pencil methods with that of students utilizing the iPad writing applications, two research questions guided the study: (1) Are there differences in student…

  8. Touch, Type, and Transform: iPads in the Social Studies Classroom

    ERIC Educational Resources Information Center

    Berson, Ilene R.; Berson, Michael J.; Manfra, Meghan McGlinn

    2012-01-01

    The release of Apple's iPad was met with great enthusiasm by educators and schools. Yet, if this new technology is retrofitted to traditional teaching activities its full potential will go unrealized. The presence of iPads alone will not generate transformative educational experiences in the social studies; however, the appropriation of the device…

  9. Investigation on hardness and impact resistance of automotive brake pad composed with rice husk dust

    NASA Astrophysics Data System (ADS)

    Bahari, Shahril Anuar; Isa, Khairul Hafizee; Kassim, Masitah Abu; Mohamed, Zulkifli; Othman, Eliasidi Abu

    2012-06-01

    In this study, hardness and impact resistance properties of automotive brake pad composed with rice husk dust (RHD) were documented. RHD was mixed with other metallic and synthetic ingredients of automotive brake pad. To obtain RHD, rice husk was ground and dried to 1 - 3% moisture content. The RHD was screened to obtain different dust sizes (80 and 100-mesh) before it was mixed with other materials at different percentages of composition (10 and 30%). The mixture was then pressed to produce brake pad. Rockwell hardness testing machine was used in hardness determination, while Izod impact testing machine was used in impact resistance determination. Hardness resistance of automotive brake pad mixed with 10% composition and 80-mesh size of RHD was significantly higher than 100-mesh. Hardness resistance of automotive brake pad mixed with 30% composition and 100-mesh size of RHD was slightly higher than 80 mesh. However, based on analysis, the difference was not significant. According to the result, hardness resistance of automotive brake pad mixed with 30% composition of RHD was higher than 10%. RHD has filled up the space and enhanced the micro structural behaviour of automotive brake pad. Impact resistance of automotive brake pad mixed with 10% composition and 80-mesh size of RHD was insignificantly higher than 100-mesh. Impact resistance of automotive brake pad mixed with 30% composition and 80-mesh size of RHD was significantly higher than 100 mesh. Large RHD size has increased the capability to resist high-rated impact loading. The impact energy was distributed over wider area for larger particle size. This factor has increased the impact resistance of automotive brake pad from large dust size. Impact resistance of automotive brake pad mixed with 80-mesh size and 30% composition of RHD was higher than 10%. In contrast, impact resistance of automotive brake pad mixed with 100-mesh size and 10% composition of RHD was higher than 30%. However, the difference was not

  10. STS-96 Launch of Discovery from Pad 39-B

    NASA Technical Reports Server (NTRS)

    1999-01-01

    Space Shuttle Discovery lifts off from Launch Pad 39B in a blaze of light amid billows of smoke and steam. With a crew of seven, mission STS-96 launches on time at 6:49:42 a.m. EDT. STS-96 is a 10-day logistics and resupply mission for the International Space Station, carrying about 4,000 pounds of supplies, to be stored aboard the station for use by future crews, including laptop computers, cameras, tools, spare parts, and clothing. The mission also includes such payloads as a Russian crane, the Strela; a U.S.-built crane; the Spacehab Oceaneering Space System Box (SHOSS), a logistics items carrier; and STARSHINE, a student- involved experiment. It will include a space walk to attach the cranes to the outside of the ISS for use in future construction. Landing is expected at the SLF on June 6 about

  11. Expedition Six Commander Ken Bowersox at pad before launch

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. - Expedition Six Commander Ken Bowersox pauses in front of Space Shuttle Endeavour at Launch Pad 39A during a tour of Kennedy Space Center prior to his launch. The primary mission of STS-113 is bringing the Expedition 6 crew to the Station and returning the Expedition 5 crew to Earth. Another major objective of the mission is delivery of the Port 1 (P1) Integrated Truss Assembly, which will be attached to the port side of the S0 truss. Three spacewalks are planned to install and activate the truss and its associated equipment. Launch of Space Shuttle Endeavour on mission STS-113 is scheduled for Nov. 11 between midnight and 4 a.m. EST.

  12. Expedition Six crew member Nikolai Budarin at pad before launch

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. - Expedition Six crew member Nikolai Budarin, of the Russian Space Agency, pauses in front of Space Shuttle Endeavour at Launch Pad 39A during a tour of Kennedy Space Center prior to his launch. The primary mission of STS-113 is bringing the Expedition 6 crew to the Station and returning the Expedition 5 crew to Earth. Another major objective of the mission is delivery of the Port 1 (P1) Integrated Truss Assembly, which will be attached to the port side of the S0 truss. Three spacewalks are planned to install and activate the truss and its associated equipment. Launch of Space Shuttle Endeavour on mission STS-113 is scheduled for Nov. 11 between midnight and 4 a.m. EST.

  13. STS-86 Crew Photo at Launch Pad 39A

    NASA Technical Reports Server (NTRS)

    1997-01-01

    With the Space Shuttle Atlantis behind them, the STS-86 crew poses for a photograph at Launch Pad 39A. The seven crew members are at KSC to participate in Terminal Countdown Demonstration Test (TCDT) activities. From left, are Mission Specialists Wendy B. Lawrence, David A. Wolf, Scott E. Parazynski, Vladimir Georgievich Titov of the Russian Space Agency, Jean-Loup J.M. Chretien of the French Space Agency, CNES; Commander James D. Wetherbee; and Pilot Michael J. Bloomfield. STS-86 will be the seventh docking of the Space Shuttle with the Russian Space Station Mir. After docking, Wolf will transfer to the Mir 24 crew, replacing astronaut C. Michael Foale, who arrived there during the last docking mission, STS-84, in May. Launch is targeted for Sept. 25.

  14. Hybrid Wing Body Planform Design with Vehicle Sketch Pad

    NASA Technical Reports Server (NTRS)

    Wells, Douglas P.; Olson, Erik D.

    2011-01-01

    The objective of this paper was to provide an update on NASA s current tools for design and analysis of hybrid wing body (HWB) aircraft with an emphasis on Vehicle Sketch Pad (VSP). NASA started HWB analysis using the Flight Optimization System (FLOPS). That capability is enhanced using Phoenix Integration's ModelCenter(Registered TradeMark). Model Center enables multifidelity analysis tools to be linked as an integrated structure. Two major components are linked to FLOPS as an example; a planform discretization tool and VSP. The planform discretization tool ensures the planform is smooth and continuous. VSP is used to display the output geometry. This example shows that a smooth & continuous HWB planform can be displayed as a three-dimensional model and rapidly sized and analyzed.

  15. Physical key-protected one-time pad

    NASA Astrophysics Data System (ADS)

    Horstmeyer, Roarke; Judkewitz, Benjamin; Vellekoop, Ivo M.; Assawaworrarit, Sid; Yang, Changhuei

    2013-12-01

    We describe an encrypted communication principle that forms a secure link between two parties without electronically saving either of their keys. Instead, random cryptographic bits are kept safe within the unique mesoscopic randomness of two volumetric scattering materials. We demonstrate how a shared set of patterned optical probes can generate 10 gigabits of statistically verified randomness between a pair of unique 2 mm3 scattering objects. This shared randomness is used to facilitate information-theoretically secure communication following a modified one-time pad protocol. Benefits of volumetric physical storage over electronic memory include the inability to probe, duplicate or selectively reset any bits without fundamentally altering the entire key space. Our ability to securely couple the randomness contained within two unique physical objects can extend to strengthen hardware required by a variety of cryptographic protocols, which is currently a critically weak link in the security pipeline of our increasingly mobile communication culture.

  16. Physical key-protected one-time pad.

    PubMed

    Horstmeyer, Roarke; Judkewitz, Benjamin; Vellekoop, Ivo M; Assawaworrarit, Sid; Yang, Changhuei

    2013-01-01

    We describe an encrypted communication principle that forms a secure link between two parties without electronically saving either of their keys. Instead, random cryptographic bits are kept safe within the unique mesoscopic randomness of two volumetric scattering materials. We demonstrate how a shared set of patterned optical probes can generate 10 gigabits of statistically verified randomness between a pair of unique 2 mm(3) scattering objects. This shared randomness is used to facilitate information-theoretically secure communication following a modified one-time pad protocol. Benefits of volumetric physical storage over electronic memory include the inability to probe, duplicate or selectively reset any bits without fundamentally altering the entire key space. Our ability to securely couple the randomness contained within two unique physical objects can extend to strengthen hardware required by a variety of cryptographic protocols, which is currently a critically weak link in the security pipeline of our increasingly mobile communication culture. PMID:24345925

  17. Space Shuttle Atlantis rolls back to Launch Pad 39A

    NASA Technical Reports Server (NTRS)

    2001-01-01

    Photographed from the top of the Vehicle Assembly Building, Space Shuttle Atlantis creeps along the crawlerway for the 3.4-mile trek to Launch Pad 39A (upper left). In the background is the Atlantic Ocean; on either side is water from the Banana Creek (left) and Banana River (right). The Shuttle has been in the VAB undergoing tests on the solid rocket booster cables. A prior extensive evaluation of NASA's SRB cable inventory on the shelf revealed conductor damage in four (of about 200) cables. Shuttle managers decided to prove the integrity of the system tunnel cables already on Atlantis, causing return of the Shuttle to the VAB a week ago. Launch of Atlantis on STS-98 has been rescheduled to Feb. 7 at 6:11 p.m. EST.

  18. STS-98 Atlantis rolls out to Launch Pad 39A

    NASA Technical Reports Server (NTRS)

    2001-01-01

    KENNEDY SPACE CENTER, Fla. -- Under cloudy skies, Space Shuttle Atlantis inches its way to Launch Pad 39A from the Vehicle Assembly Building (right). The journey is a distance of just over 3 miles. The water in the foreground is part of Banana Creek. Atlantis will fly on mission STS-98, the seventh construction flight to the International Space Station. The orbiter will carry in its payload bay the U.S. Laboratory, named Destiny, that will have five system racks already installed inside the module. After delivery of electronics in the lab, electrically powered attitude control for Control Moment Gyroscopes will be activated. Atlantis is scheduled for launch no earlier than Jan. 19, 2001, with a crew of five.

  19. STS-111 Endeavour rollout to Launch Pad 39-A

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- The U.S. flag and orbiter's flag wave in the foreground after Space Shuttle Endeavour's rollout to Launch Pad 39A from the Vehicle Assembly Building. The Shuttle comprises the orbiter, in front, and the taller orange external tank behind it flanked by twin solid rocket boosters. Mission STS-111 is designated UF-2, the 14th assembly flight to the International Space Station. Endeavour's payload includes the Multi-Purpose Logistics Module Leonardo and Mobile Base System. The mission also will swap resident crews on the Station, carrying the Expedition 5 crew and returning to Earth Expedition 4. Liftoff of Endeavour is scheduled between 4 and 8 p.m. May 30, 2002.

  20. STS-111 Endeavour rollout to Launch Pad 39-A

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- Space Shuttle Endeavour rests on Launch Pad 39A after rollout from the Vehicle Assembly Building. The Shuttle comprises the orbiter, in front, and the taller orange external tank behind it flanked by twin solid rocket boosters. On either side of Endeavour's tail and main engines are the tail service masts that support the fluid,, gas and electrical requirements of the orbiter's liquid oxyen and liquid hydrogen aft T-0 umbilicals. Mission STS-111 is designated UF-2, the 14th assembly flight to the International Space Station. Endeavour's payload includes the Multi-Purpose Logistics Module Leonardo and Mobile Base System. The mission also will swap resident crews on the Station, carrying the Expedition 5 crew and returning to Earth Expedition 4. Liftoff of Endeavour is scheduled between 4 and 8 p.m. May 30, 2002.

  1. STS-110 crew around Launch Pad 39-A during TCDT

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- The STS-110 crew poses on the 225-foot level of the Fixed Service Structure on the launch pad during Terminal Countdown Demonstration Test activities. Kneeling in front are Pilot Stephen Frick and Mission Specialist Jerry Ross. Behind them are Mission Specialists Ellen Ochoa and Rex Walheim. In the rear are Commander Michael Bloomfield and Mission Specialists Lee Morin and Steven Smith. The TCDT, which includes emergency egress training and a simulated launch countdown, is held at KSC prior to each Space Shuttle flight. Scheduled for launch April 4, the 11-day mission will feature Shuttle Atlantis docking with the International Space Station (ISS) and delivering the S0 truss, the centerpiece-segment of the primary truss structure that will eventually extend over 300 feet.

  2. STS-110 Atlantis rolls out to Launch Pad 39-A

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- Sitting atop the Mobile Launcher Platform, Space Shuttle Atlantis inches its way to the launch pad. The Shuttle and MLP rest on top of the crawler-transporter beneath it, which moves about 1 mile per hour. Atlantis is scheduled for launch April 4 on mission STS-110, which will install the S0 truss, the framework that eventually will hold the power and cooling systems needed for future international research laboratories on the International Space Station. The Canadarm2 robotic arm will be used exclusively to hoist the 13-ton truss from the payload bay to the Station. The S0 truss will be the first major U.S. component launched to the Station since the addition of the Quest airlock in July 2001. The four spacewalks planned for the construction will all originate from the airlock. The mission will be Atlantis' 25th trip to space.

  3. STS-110 Atlantis rolls out to Launch Pad 39-A

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. - Space Shuttle Atlantis crawls at less than 1 mph (<1.5 kilometers) along the crawlerway to the launch pad. The Shuttle sits on top of the Mobile Launcher Platform, which rests on the crawler-transporter. Atlantis is scheduled for launch April 4 on mission STS-110, which will install the S0 truss, the framework that eventually will hold the power and cooling systems needed for future international research laboratories on the International Space Station. The Canadarm2 robotic arm will be used exclusively to hoist the 13-ton truss from the payload bay to the Station. The S0 truss will be the first major U.S. component launched to the Station since the addition of the Quest airlock in July 2001. The four spacewalks planned for the construction will all originate from the airlock. The mission will be Atlantis' 25th trip to space.

  4. STS-111 Endeavour rollout to Launch Pad 39-A

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. - Space Shuttle Endeavour arrives at Launch Pad 39A shortly after 9 a.m. to begin processing operations for launch on mission STS-111. The slow journey along the crawlerway took 6.5 hours at a speed of 0.9 mph. The Shuttle sits atop its Mobile Launcher Platform, which travels on the crawler-transporter. At left is the open Rotating Service Structure and the Fixed Service Structure behind it, with its 80-foot lightning mast on top. Mission STS-111 is designated UF-2, the 14th assembly flight to the International Space Station. Endeavour's payload includes the Multi-Purpose Logistics Module Leonardo and Mobile Base System. The mission also will swap resident crews on the Station, carrying the Expedition 5 crew and returning to Earth Expedition 4. Liftoff of Endeavour is scheduled between 4 and 8 p.m. May 30, 2002.

  5. STS-110 Atlantis rolls out to Launch Pad 39-A

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. - This closeup shows Space Shuttle Atlantis as it begins rolling out of the Vehicle Assembly Building on its slow trek to the launch pad. Below Atlantis' wings are the Tail Service Masts on the Mobile Launcher Platform. Atlantis is scheduled for launch April 4 on mission STS-110, which will install the S0 truss, the framework that eventually will hold the power and cooling systems needed for future international research laboratories on the International Space Station. The Canadarm2 robotic arm will be used exclusively to hoist the 13-ton truss from the payload bay to the Station. The S0 truss will be the first major U.S. component launched to the Station since the addition of the Quest airlock in July 2001. The four spacewalks planned for the construction will all originate from the airlock. The mission will be Atlantis' 25th trip to space.

  6. STS-110 Atlantis rolls out to Launch Pad 39-A

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- Space Shuttle Atlantis begins rolling out of the Vehicle Assembly Building on its slow trek tothe launch pad. Atlantis is scheduled for launch April 4 on mission STS-110, which will install the S0 truss, the framework that eventually will hold the power and cooling systems needed for future international research laboratories on the International Space Station. The Canadarm2 robotic arm will be used exclusively to hoist the 13-ton truss from the payload bay to the Station. The S0 truss will be the first major U.S. component launched to the Station since the addition of the Quest airlock in July 2001. The four spacewalks planned for the construction will all originate from the airlock. The mission will be Atlantis' 25th trip to space.

  7. STS-111 Endeavour rollout to Launch Pad 39-A

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- Space Shuttle Endeavour is silhouetted against the morning sun as it arrives on Launch Pad 39A to begin processing operations for launch on mission STS-111. The slow journey along the crawlerway took 6.5 hours at a speed of 0.9 mph. The Shuttle sits atop its Mobile Launcher Platform, which travels on the crawler-transporter. At left is the open Rotating Service Structure and the Fixed Service Structure behind it, with its 80-foot lightning mast on top. Mission STS-111 is designated UF-2, the 14th assembly flight to the International Space Station. Endeavour's payload includes the Multi-Purpose Logistics Module Leonardo and Mobile Base System. The mission also will swap resident crews on the Station, carrying the Expedition 5 crew and returning to Earth Expedition 4. Liftoff of Endeavour is scheduled between 4 and 8 p.m. May 30, 2002.

  8. Advanced Strain-Isolation-Pad Material with Bonded Fibrous Construction

    NASA Technical Reports Server (NTRS)

    Seibold, R. W.; Saito, C. A.; Buller, B. W.

    1982-01-01

    The feasibility of utilizing air lay and liquid lay felt deposition techniques to fabricate strain isolation pad (SIP) materials for the Space Shuttle Orbiter was demonstrated. These materials were developed as candidate replacements for the present needled felt SIP used between the ceramic tiles and the aluminum skin on the undersurface of the Orbiter. The SIP materials that were developed consisted of high temperature aramid fibers deposited by controlled fluid (air or liquid) carriers to form low density unbonded felts. The deposited felts were then bonded at the fiber intersections with a small amount of high temperature polyimide resin. This type of bonded felt construction can potentially eliminate two of the problems associated with the present SIP, viz., transmittal of localized stresses into the tiles and load history dependent mechanical response. However, further work is needed to achieve adequate through thickness tensile strength in the bonded felts.

  9. Physical key-protected one-time pad

    PubMed Central

    Horstmeyer, Roarke; Judkewitz, Benjamin; Vellekoop, Ivo M.; Assawaworrarit, Sid; Yang, Changhuei

    2013-01-01

    We describe an encrypted communication principle that forms a secure link between two parties without electronically saving either of their keys. Instead, random cryptographic bits are kept safe within the unique mesoscopic randomness of two volumetric scattering materials. We demonstrate how a shared set of patterned optical probes can generate 10 gigabits of statistically verified randomness between a pair of unique 2 mm3 scattering objects. This shared randomness is used to facilitate information-theoretically secure communication following a modified one-time pad protocol. Benefits of volumetric physical storage over electronic memory include the inability to probe, duplicate or selectively reset any bits without fundamentally altering the entire key space. Our ability to securely couple the randomness contained within two unique physical objects can extend to strengthen hardware required by a variety of cryptographic protocols, which is currently a critically weak link in the security pipeline of our increasingly mobile communication culture. PMID:24345925

  10. Moonlit View of Apollo 17 On Launch Pad

    NASA Technical Reports Server (NTRS)

    1972-01-01

    This is a breathtaking moonlit view of Apollo 17 on the Launch Pad at Kennedy Space Flight Center (KSC). The seventh and last manned lunar landing and return to Earth mission, the Apollo 17, carrying a crew of three astronauts: Mission Commander Eugene A. Cernan, Lunar Module pilot Harrison H. Schmitt, and Command Module pilot Ronald E. Evans, lifted off on December 7, 1972. The basic objective of the Apollo 17 mission was to sample basin-rim highland material and adjacent mare material, and investigate the geological evolutionary relationship between these two major units. The mission marked the longest Apollo mission, 504 hours, and the longest lunar surface stay time, 75 hours, which allowed the astronauts to conduct an extensive geological investigation. They collected 257 pounds (117 kilograms) of lunar samples with the use of the Marshall Space Flight Center designed Lunar Roving Vehicle (LRV). The mission ended on December 19, 1972.

  11. Space Shuttle Discovery rolls out to the launch pad

    NASA Technical Reports Server (NTRS)

    1999-01-01

    Space Shuttle Discovery sits on Launch Pad 39B against a backdrop of blue sky and the blue-green Atlantic Ocean. At the top left is the 290-foot-high water tank that holds 300,000 gallons of water for the sound suppression system during liftoff. At the bottom, on the Rotating Service Structure, is photographer John Sexton, taking photos for a book. Liftoff of Discovery on mission STS-96 is targeted for May 20 at 9:32 a.m. EDT. STS-96 is a logistics and resupply mission for the International Space Station, carrying such payloads as a Russian crane, the Strela; a U.S.- built crane; the Spacehab Oceaneering Space System Box (SHOSS), a logistics items carrier; and STARSHINE, a student-led experiment.

  12. The STS-98 crew practices emergency egress from the pad

    NASA Technical Reports Server (NTRS)

    2001-01-01

    KENNEDY SPACE CENTER, Fla. -- During emergency egress training at the 195-foot level of the Fixed Service Structure, Mission Specialist Marsha Ivins take her place in the slidewire basket while Mission Specialist Robert Curbeam reaches for the release handle. The basket slides along a 1200-foot wire to the landing zone below and nearby bunker. The crew has been taking part in Terminal Countdown Demonstration Test activities, which include the simulated countdown and emergency egress training at the pad. STS-98 is the seventh construction flight to the International Space Station, carrying as payload the U.S. Lab Destiny, a key element in the construction of the ISS. Launch of STS-98 is scheduled for Jan. 19 at 2:11 a.m. EST.

  13. The STS-98 crew practices emergency egress from the pad

    NASA Technical Reports Server (NTRS)

    2001-01-01

    KENNEDY SPACE CENTER, Fla. -- Fully dressed in their launch and entry suits, STS-98 Mission Specialists Thomas Jones (left), Marsha Ivins and Robert Curbeam practice a speedy exit from the Fixed Service Structure during emergency egress training. They are heading for the slidewire baskets that slide along a 1200-foot wire to the landing zone below and nearby bunker. The crew has been taking part in Terminal Countdown Demonstration Test activities, which include the simulated countdown and emergency egress training at the pad. STS-98 is the seventh construction flight to the International Space Station, carrying as payload the U.S. Lab Destiny, a key element in the construction of the ISS. Launch of STS-98 is scheduled for Jan. 19 at 2:11 a.m. EST.

  14. The STS-98 crew practices emergency egress from the pad

    NASA Technical Reports Server (NTRS)

    2001-01-01

    KENNEDY SPACE CENTER, Fla. -- During emergency egress training at the 195-foot level of the Fixed Service Structure, Pilot Mark Polansky settles in the slidewire basket while Commander Ken Cockrell reaches for the release handle. The basket slides along a 1200-foot wire to the landing zone below and nearby bunker. The crew has been taking part in Terminal Countdown Demonstration Test activities, which include the simulated countdown and emergency egress training at the pad. STS-98 is the seventh construction flight to the International Space Station, carrying as payload the U.S. Lab Destiny, a key element in the construction of the ISS. Launch of STS-98 is scheduled for Jan. 19 at 2:11 a.m. EST.

  15. Dermatological testing of an emollient-treated menstrual pad with a novel foam absorbent core.

    PubMed

    Farage, Miranda A; Segarra, Vanessa Silva; Bramante, Mario; Elsner, Peter; Maibach, Howard I

    2008-01-01

    Dermatological testing was used to assess the skin compatibility of a menstrual pad with an emollient-treated surface layer and a novel, polymeric absorbent foam core. The test program included: 1) skin patch tests to assess cumulative skin irritation, 2) human repeat insult patch tests to assess the potential for contact sensitization, and 3) repeated application to the popliteal fossa ("behind-the-knee" test) to assess combined chemical irritation and frictional effects. Studies showed the new product and its components to be as mild to skin as other commercially available materials with no evidence for the induction of delayed contact hypersensitivity. Pads with an emollient-based topsheet finish were milder to the skin than pads with a conventional topsheet finish. The test program provides reassurance that the skin compatibility of the new menstrual pad is similar to that of conventional marketed pads with a history of safe use and consumer acceptance. PMID:19037765

  16. An Unusual Cause of Posterior Elbow Impingement: Detachment of a Hypertrophied Posterior Fat Pad.

    PubMed

    Hamada, Daisuke; Matsuura, Tetsuya; Sugiura, Kosuke; Higuchi, Tadahiro; Suzue, Naoto; Goto, Tomohiro; Tsutsui, Takahiko; Wada, Keizo; Fukuta, Shoji; Sairyo, Koichi

    2015-01-01

    We report a case of a 47-year-old woman who developed posterior impingement of the elbow due to detachment of a hypertrophied posterior fat pad. She reported acute left elbow pain after leaning back onto a hard object with her hand and subsequently experienced a "catching" sensation. Comparison with the magnetic resonance images of a normal elbow revealed a hypertrophied posterior fat pad interposed between the olecranon and olecranon fossa in both elbows, with the fat pad in the left elbow located more inferiorly than that in the right elbow. Elbow arthroscopy showed the olecranon fossa covered by the fat pad, a portion of which was detached from the rest of the pad. Debridement of the detached portion was performed until no impingement was evident. Postoperatively, full extension of the elbow did not elicit pain. Clinicians should include this pathology among the differential diagnoses for posterior elbow pain. PMID:26613057

  17. A padding method to reduce edge effects for enhanced damage identification using wavelet analysis

    NASA Astrophysics Data System (ADS)

    Montanari, Lorenzo; Basu, Biswajit; Spagnoli, Andrea; Broderick, Brian M.

    2015-02-01

    Vibration response based structural damage identification by spatial wavelet analysis is widely considered a powerful tool in Structural Health Monitoring (SHM). This work deals with the issue of border distortions in wavelet transform that can mask tiny damages close to the boundary of a structure. Since traditional padding methods (e.g., zero-padding, symmetric padding, linear padding) are often not satisfactory, a simple and computationally inexpensive signal extension method, based on fitting polynomial functions and continuity conditions at the extrema, is proposed. The method is applied to analyze noisy mode shapes and static deflection of cracked cantilever and simply supported beams. The effectiveness and the versatility of the method in localizing tiny damages close to clamped, free or hinged beam boundaries is demonstrated. Furthermore, an extensive comparison with the linear padding method and Messina's isomorphism methods is carried out.

  18. An Unusual Cause of Posterior Elbow Impingement: Detachment of a Hypertrophied Posterior Fat Pad

    PubMed Central

    Hamada, Daisuke; Matsuura, Tetsuya; Sugiura, Kosuke; Higuchi, Tadahiro; Suzue, Naoto; Goto, Tomohiro; Tsutsui, Takahiko; Wada, Keizo; Fukuta, Shoji; Sairyo, Koichi

    2015-01-01

    We report a case of a 47-year-old woman who developed posterior impingement of the elbow due to detachment of a hypertrophied posterior fat pad. She reported acute left elbow pain after leaning back onto a hard object with her hand and subsequently experienced a “catching” sensation. Comparison with the magnetic resonance images of a normal elbow revealed a hypertrophied posterior fat pad interposed between the olecranon and olecranon fossa in both elbows, with the fat pad in the left elbow located more inferiorly than that in the right elbow. Elbow arthroscopy showed the olecranon fossa covered by the fat pad, a portion of which was detached from the rest of the pad. Debridement of the detached portion was performed until no impingement was evident. Postoperatively, full extension of the elbow did not elicit pain. Clinicians should include this pathology among the differential diagnoses for posterior elbow pain. PMID:26613057

  19. Frictional Characterization of Chemical-Mechanical Polishing Pad Surface and Diamond Conditioner Wear

    NASA Astrophysics Data System (ADS)

    Yamada, Yohei; Kawakubo, Masanori; Hirai, Osamu; Konishi, Nobuhiro; Kurokawa, Syuhei; Doi, Toshiro

    2008-08-01

    We evaluated a contact metrology instrument used in chemical-mechanical polishing (CMP) systems for high-volume manufacture and examined in situ coefficient of friction (COF) monitoring to identify the tribology of CMP, and subsequently to determine the useful lifespan of consumables. The results showed that the direct measurement of the wear of the pad allowed for an accurate determination of both pad thickness and the ideal time to replace the pad and conditioner disk based on pad wear rate. We also presented a clear correlation between the working grid area of the conditioner disk and the tribological behavior of the pad break-in procedure, leading to the result showing that the variation in tungsten film removal rate decreased as the working grid density of the conditioner disk increased. This study has proven the effectiveness of measuring friction force for better CMP control.

  20. Determination of alkylamine permeation through protective gloves using aliphatic amine pads.

    PubMed

    Vo, E; Berardinelli, S P

    1999-12-01

    A quantitative study of alkylamine permeation through a glove material using Permea-Tec aliphatic amine pads, used for the detection of chemical breakthrough of protective clothing, was performed for triethylamine following a microwave-extraction process and gas chromatographic analysis. Triethylamine exhibited > 99% adsorption on the pads at a spiking level of 729 ng (1.0 ml). Triethylamine showed recoveries from 63 to 90% (RSD < or = 5%) over the range 0.2-1.0 ml (146-729 ng) applied to pads. The ASTM F739 standard and direct permeability testing procedures were used to determine breakthrough times for five protective glove materials using triethylamine as a challenge chemical. Breakthrough times for six protective gloves were determined ranging from 40 s to > 4 h. The quantitative concentration of triethylamine on the pads following permeation through the gloves was also determined, ranging from 101 to 103 ng cm-2 (382-386 ng per pad). PMID:11529186

  1. The fine structure of the rectal pads of Zorotypus caudelli Karny (Zoraptera, Insecta).

    PubMed

    Dallai, R; Mercati, D; Mashimo, Y; Machida, R; Beutel, R G

    2016-07-01

    The rectal pads of a species of the controversial polyneopteran order Zoraptera were examined using histological sections and TEM micrographs. Six pads are present along the thin rectal epithelium. Each pad consists of a few large principal cells surrounded by flattened junctional cells, which extend also beneath the principal cells. The cells are lined by a thin apical cuticle. No basal cells and no cavity have been observed beneath the pad. Principal cells have a regular layer of apical microvilli and are joined by intercellular septate junctions, which are interrupted by short dilatations of the intercellular space. At these levels the two adjacent plasma membranes are joined by short zonulae adhaerentes. In the cytoplasm, a rich system of strict associations between lateral plasma membranes and mitochondria forms scalariform junctions. Rectal pads share ultrastructural features with similar excretory organs of several neopteran groups, in particular with Blattodea (roaches and termites) and Thysanoptera, and are involved in fluid reabsorption and ion regulation. PMID:27368527

  2. STS-103 crew pose in front of Pad 39B

    NASA Technical Reports Server (NTRS)

    1999-01-01

    During Terminal Countdown Demonstration Test (TDCT) activities at Launch Pad 39B, the STS-103 crew pose in front of the flame trench, which is situated underneath the Mobile Launcher Platform holding Space Shuttle Discovery. Standing left to right are Mission Specialists Claude Nicollier of Switzerland, who is with the European Space Agency (ESA), C. Michael Foale (Ph.D.), John M. Grunsfeld (Ph.D.), Pilot Scott J. Kelly, Commander Curtis L. Brown Jr., and Mission Specialists Jean-Frangois Clervoy of France, also with ESA, and Steven L. Smith. One of the solid rocket boosters and the external tank that are attached to Discovery can be seen in the photo. The flame trench is made of concrete and refractory brick, and contains an orbiter flame deflector on one side and solid rocket booster flame deflector on the other. The deflectors protect the flame trench floor and pad surface from the intense heat of launch. The TCDT provides the crew with emergency egress training, opportunities to inspect their mission payloads in the orbiter's payload bay, and simulated countdown exercises. STS-103 is a 'call-up' mission due to the need to replace and repair portions of the Hubble Space Telescope, including the gyroscopes that allow the telescope to point at stars, galaxies and planets. The STS-103 crew will be replacing a Fine Guidance Sensor, an older computer with a new enhanced model, an older data tape recorder with a solid-state digital recorder, a failed spare transmitter with a new one, and degraded insulation on the telescope with new thermal insulation. The crew will also install a Battery Voltage/Temperature Improvement Kit to protect the spacecraft batteries from overcharging and overheating when the telescope goes into a safe mode. Four EVA's are planned to make the necessary repairs and replacements on the telescope. The mission is targeted for launch Dec. 6 at 2:37 a.m. EST.

  3. A binocular iPad treatment for amblyopic children

    PubMed Central

    Li, S L; Jost, R M; Morale, S E; Stager, D R; Dao, L; Stager, D; Birch, E E

    2014-01-01

    Purpose Monocular amblyopia treatment (patching or penalization) does not always result in 6/6 vision and amblyopia often recurs. As amblyopia arises from abnormal binocular visual experience, we evaluated the effectiveness of a novel home-based binocular amblyopia treatment. Methods Children (4–12 y) wore anaglyphic glasses to play binocular games on an iPad platform for 4 h/w for 4 weeks. The first 25 children were assigned to sham games and then 50 children to binocular games. Children in the binocular group had the option of participating for an additional 4 weeks. Compliance was monitored with calendars and tracking fellow eye contrast settings. About half of the children in each group were also treated with patching at a different time of day. Best-corrected visual acuity, suppression, and stereoacuity were measured at baseline, at the 4- and 8-week outcome visits, and 3 months after cessation of treatment. Results Mean (±SE) visual acuity improved in the binocular group from 0.47±0.03 logMAR at baseline to 0.39±0.03 logMAR at 4 weeks (P<0.001); there was no significant change for the sham group. The effect of binocular games on visual acuity did not differ for children who were patched vs those who were not. The median stereoacuity remained unchanged in both groups. An additional 4 weeks of treatment did not yield additional visual acuity improvement. Visual acuity improvements were maintained for 3 months after the cessation of treatment. Conclusions Binocular iPad treatment rapidly improved visual acuity, and visual acuity was stable for at least 3 months following the cessation of treatment. PMID:25060850

  4. Pilot Study of iPad Incorporation Into Graduate Medical Education

    PubMed Central

    Lobo, Mark J.; Crandley, Edwin F.; Rumph, Jake S.; Kirk, Susan E.; Dunlap, Neal E.; Rahimi, Asal S.; Turner, A. Benton; Larner, James M.; Read, Paul W.

    2013-01-01

    Background Increased documentation and charting requirements are challenging for residents, given duty hour limits. Use of mobile electronic devices may help residents complete these tasks efficiently. Objective To collect initial data on usage rates, information technology (IT) support requirements, and resident use of iPads during training. Methods In this pilot study, we provided 12 residents/fellows from various specialties at the University of Virginia with an iPad with IT support. The system used a virtual private network with access to the institution's electronic health record. Participants were allowed to develop their own methods and systems for personalized iPad use, and after 9 months they provided data on the utility of the iPad. Feedback from the IT team also was obtained. Results Average iPad use was 2.1 h/d (range, 0.5–6 h/d). The average self-reported reduction in administrative work due to the iPad was 2.7 h/wk (range, 0–9 h/wk). A total of 75% (9 of 12) of the users would recommend universal adoption among residents and fellows. More than 90% (11 of 12) of users reported the iPad would improve communication for coordination of care. A total of 68% (8 of 12) of users reported that an iPad facilitated their activities as educators of medical students and junior residents. Residents cited slow data entry into the electronic health record and hospital areas lacking Wi-Fi connectivity as potential drawbacks to iPad use. The IT team reported minimal support time for device setup, maintenance, and upgrades, and limited security risks. Conclusions The iPad may contribute to increased clinical efficiency, reduced hours spent on administrative tasks, and enhanced educational opportunities for residents, with minimal IT support. PMID:24404242

  5. Extreme positive allometry of animal adhesive pads and the size limits of adhesion-based climbing.

    PubMed

    Labonte, David; Clemente, Christofer J; Dittrich, Alex; Kuo, Chi-Yun; Crosby, Alfred J; Irschick, Duncan J; Federle, Walter

    2016-02-01

    Organismal functions are size-dependent whenever body surfaces supply body volumes. Larger organisms can develop strongly folded internal surfaces for enhanced diffusion, but in many cases areas cannot be folded so that their enlargement is constrained by anatomy, presenting a problem for larger animals. Here, we study the allometry of adhesive pad area in 225 climbing animal species, covering more than seven orders of magnitude in weight. Across all taxa, adhesive pad area showed extreme positive allometry and scaled with weight, implying a 200-fold increase of relative pad area from mites to geckos. However, allometric scaling coefficients for pad area systematically decreased with taxonomic level and were close to isometry when evolutionary history was accounted for, indicating that the substantial anatomical changes required to achieve this increase in relative pad area are limited by phylogenetic constraints. Using a comparative phylogenetic approach, we found that the departure from isometry is almost exclusively caused by large differences in size-corrected pad area between arthropods and vertebrates. To mitigate the expected decrease of weight-specific adhesion within closely related taxa where pad area scaled close to isometry, data for several taxa suggest that the pads' adhesive strength increased for larger animals. The combination of adjustments in relative pad area for distantly related taxa and changes in adhesive strength for closely related groups helps explain how climbing with adhesive pads has evolved in animals varying over seven orders of magnitude in body weight. Our results illustrate the size limits of adhesion-based climbing, with profound implications for large-scale bio-inspired adhesives. PMID:26787862

  6. Effects of a thermal-insulating mouse pad on temperature of forearm and hand during computer tasks.

    PubMed

    Meijer, Eline M; Formanoy, Margriet A G; Visser, Bart; Sluiter, Judith K; Frings-Dresen, Monique H W

    2006-07-15

    This laboratory experiment studied the effects of a thermal-insulating mouse pad on arm temperature and comfort during computer work. Fourteen subjects performed two 20-min computer tasks (a mouse task and a combined task alternating keyboard and mouse use), under three conditions, namely with: 1) a thermal-insulating pad; 2) a placebo pad; 3) no pad (desktop). The temperatures of the forearm, wrist, hand and fingers were measured with four thermocouples. Comfort and discomfort were determined by two visual analogue scales. No arm temperature differences were found between the experimental conditions after performing the combination task in any location. After the mouse task, however, arm temperature decreased significantly less with the thermal-insulating mouse pad than with the placebo pad. The thermal-insulating pad was rated as more comfortable and less uncomfortable than a regular desktop during mouse tasks. A large size is recommended for the thermal-insulating pad. PMID:16801230

  7. iPad® Use in Children and Young Adults with Autism Spectrum Disorder: An Observational Study

    ERIC Educational Resources Information Center

    King, Amie M.; Thomeczek, Melissa; Voreis, Grayce; Scott, Victoria

    2014-01-01

    This exploratory study was conducted to describe how children and young adults with autism spectrum disorder (ASD) are currently using iPads® and applications, to explore the role of education professionals on iPad® and application use, and to determine potential research needs regarding iPad® use in children with ASD. Naturalistic observations…

  8. Efficacy of an improved absorbent pad on incontinence-associated dermatitis in older women: cluster randomized controlled trial

    PubMed Central

    2012-01-01

    Background Most older adults with urinary incontinence use absorbent pads. Because of exposure to moisture and chemical irritating substances in urine, the perineal skin region is always at risk for development of incontinence-associated dermatitis (IAD). The aim of this study was to examine the efficacy of an improved absorbent pad against IAD. Methods A cluster randomized controlled design was used to compare the efficacy of two absorbent pads. Female inpatients aged ≥65 years who had IAD and used an absorbent pad or diaper all day were enrolled. Healing rate of IAD and variables of skin barrier function such as skin pH and skin moisture were compared between the usual absorbent pad group (n = 30) and the test absorbent pad group (n = 30). Results Thirteen patients (43.3%) from the test absorbent pad group and 4 patients (13.3%) from the usual absorbent pad group recovered completely from IAD. Moreover, the test absorbent pad group healed significantly faster than the usual absorbent pad group (p = 0.009). On the other hand, there were no significant differences between the two groups in skin barrier function. Conclusion The test absorbent pad for older adults with urinary incontinence might be more efficacious against IAD than usual absorbent pad. Trial registration UMIN-CTR: UMIN000006188 PMID:22642800

  9. 77 FR 21554 - Alaska Energy Authority; Notice of Extension of Time To File Comments on the Pad and Scoping...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-10

    ... Pad and Scoping Document, and To Identify Issues and Associated Study Requests On February 24, 2012... (PAD) and Commencement of Pre-Filing Process; Notice of Intent to Prepare an Environmental Impact Statement and Conduct Scoping; Request for Comments on the PAD and Scoping Document, and Identification...

  10. 40 CFR 165.92 - What if I need both a containment pad and a secondary containment unit?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false What if I need both a containment pad... Containment Structures § 165.92 What if I need both a containment pad and a secondary containment unit? You may combine containment pads and secondary containment units as an integrated system provided...

  11. Mesh skin graft and digital pad transfer to reconstruct the weight-bearing surface in a dog

    PubMed Central

    Rahal, Sheila C.; Mortari, Ana C.; Morishin Filho, Milton M.

    2007-01-01

    A 2-month-old dog was presented with injuries involving both hind paws. Only the 5th digit and its digital pad were present on the right paw. Following a full-thickness skin graft, the 5th digital pad was transferred distal to the metatarsal bones. The transferred pad permitted weight-bearing on the limb. PMID:18189047

  12. Digital Scribes: A Qualitative Study of Graduate Students Who Brought iPads into Their Academic Lives

    ERIC Educational Resources Information Center

    Alyahya, Suzan; Gall, James

    2015-01-01

    The purpose of this qualitative research was to examine how graduate students at one institution used personal iPads to support their educational needs. This study specifically addressed the questions: What do graduate students describe as the important educational benefits of their iPads? In what ways are graduate students using iPads to study…

  13. iTE: Student Teachers Using iPad on a Second Level Initial Teacher Education Programme

    ERIC Educational Resources Information Center

    Mac Mahon, Brendan; Grádaigh, Seán Ó.; Ghuidhir, Sinéad Ní

    2016-01-01

    Research on the use of iPad in initial teacher education is limited. This paper outlines a study to examine how the professional learning and pedagogical knowledge development of student teachers could be supported following 1:1 iPad deployment on a second-level initial teacher education programme in Ireland. Findings show that iPad can be…

  14. School Administrators' Use of iPads: Impact of Training and Attitudes toward School Use

    ERIC Educational Resources Information Center

    Dogan, Bulent; Almus, Kadir

    2014-01-01

    As Apple iPads are increasingly being adopted in schools for educational purposes, school administrators are seen as the key facilitators in the implementation of this new technology. This survey-based quantitative study investigated the impact of receiving iPad training on school administrators' attitudes towards iPad use in their…

  15. iPad Use in Iowa Research Network Family Physician Offices

    PubMed Central

    Daly, Jeanette M.; Xu, Yinghui; Levy, Barcey T.

    2015-01-01

    Background Through a cancer research infrastructure building grant, iPads were given to healthcare providers in family physician offices. The purpose of this study was to determine the use and application of iPads in the Iowa Research Network. Methods A Qualtrics survey was sent to 81 iPad recipients after Institutional Review Board approval. Results Fifty-nine percent responded and 85% reported they have used the iPad. The main reason for use of the iPad was browsing the World Wide Web for healthcare information. Open-ended comments supported use of the iPad for photographic documentation of wound and other skin lesions for insertion into the medical record and it helped improve clinic flow by making it easier to put orders in the system through the iPad. Conclusions Tablet uses are variable in physician offices with provider’s gathering health care information from the Internet and securing education material for patients as the frequent usages. PMID:25398430

  16. Effect of shear forces and ageing on the compliance of adhesive pads in adult cockroaches.

    PubMed

    Zhou, Yanmin; Robinson, Adam; Viney, Christine; Federle, Walter

    2015-09-01

    The flexibility of insect adhesive pads is crucial for their ability to attach on rough surfaces. Here, we used transparent substrates with micropillars to test in adult cockroaches (Nauphoeta cinerea) whether and how the stiffness of smooth adhesive pads changes when shear forces are applied, and whether the insect's age has any influence. We found that during pulls towards the body, the pad's ability to conform to the surface microstructures was improved in comparison to a contact without shear, suggesting that shear forces make the pad more compliant. The mechanism underlying this shear-dependent increase in compliance is still unclear. The effect was not explained by viscoelastic creep, changes in normal pressure, or shear-induced pad rolling, which brings new areas of cuticle into surface contact. Adhesive pads were significantly stiffer in older cockroaches. Stiffness increased most rapidly in cockroaches aged between 2.5 and 4 months. This increase is probably based on wear and repair of the delicate adhesive cuticle. Recent wear (visualised by Methylene Blue staining) was not age dependent, whereas permanent damage (visible as brown scars) accumulated with age, reducing the pads' flexibility. PMID:26206353

  17. Frictional and heat resistance characteristics of coconut husk particle filled automotive brake pad

    NASA Astrophysics Data System (ADS)

    Bahari, Shahril Anuar; Chik, Mohd Syahrizul; Kassim, Masitah Abu; Som Said, Che Mohamad; Misnon, Mohd Iqbal; Mohamed, Zulkifli; Othman, Eliasidi Abu

    2012-06-01

    The objective of this study was to determine the friction and heat resistance characteristics of automotive brake pad composed with different sizes and percentages of coconut husk particle. The materials used were phenolic resin (phenol formaldehyde) as binder, copper, graphite and brass as friction producer/modifiers, magnesium oxide as abrasive material, steel and barium sulfate as reinforcement while coconut husk particle as filler. To obtain particle, the coconut husk was ground and dried to 3% moisture content. Then the coconut husk particle was screened using 80 mesh (to obtain coarse dust) and 100 mesh (to obtain fine dust). Different percentages of particle, such as 10 and 30% were used in the mixture of brake pad materials. Then the mixture was hot-pressed to produce brake pad. Chase machine was used to determine the friction coefficient in friction resistance testing, while thermogravimetric analyzer (TGA) machine was used to determine the heat decomposition values in heat resistance testing. Results showed that brake pad with 100 mesh and 10% composition of coconut husk particle showed the highest friction coefficient. For heat resistance, brake pad with 100 mesh and 30% composition of coconut husk dust showed the highest decomposition temperature, due to the high percentage of coconut husk particle in the composition, thus increased the thermal stability. As a comparison, brake pad composed with coconut husk particle showed better heat resistance results than commercial brake pad.

  18. Simulating pad-electrodes with high-definition arrays in transcranial electric stimulation

    NASA Astrophysics Data System (ADS)

    Kempe, René; Huang, Yu; Parra, Lucas C.

    2014-04-01

    Objective. Research studies on transcranial electric stimulation, including direct current, often use a computational model to provide guidance on the placing of sponge-electrode pads. However, the expertise and computational resources needed for finite element modeling (FEM) make modeling impractical in a clinical setting. Our objective is to make the exploration of different electrode configurations accessible to practitioners. We provide an efficient tool to estimate current distributions for arbitrary pad configurations while obviating the need for complex simulation software. Approach. To efficiently estimate current distributions for arbitrary pad configurations we propose to simulate pads with an array of high-definition (HD) electrodes and use an efficient linear superposition to then quickly evaluate different electrode configurations. Main results. Numerical results on ten different pad configurations on a normal individual show that electric field intensity simulated with the sampled array deviates from the solutions with pads by only 5% and the locations of peak magnitude fields have a 94% overlap when using a dense array of 336 electrodes. Significance. Computationally intensive FEM modeling of the HD array needs to be performed only once, perhaps on a set of standard heads that can be made available to multiple users. The present results confirm that by using these models one can now quickly and accurately explore and select pad-electrode montages to match a particular clinical need.

  19. Evolution of multi-well pad development and influence of well pads on environmental violations and wastewater volumes in the Marcellus shale (USA).

    PubMed

    Manda, Alex K; Heath, Jamie L; Klein, Wendy A; Griffin, Michael T; Montz, Burrell E

    2014-09-01

    A majority of well pads for unconventional gas wells that are drilled into the Marcellus shale (northeastern USA) consist of multiple wells (in some cases as many as 12 wells per pad), yet the influence of the evolution of well pad development on the extent of environmental violations and wastewater production is unknown. Although the development of multi-well pads (MWP) at the expense of single well pads (SWP) has been mostly driven by economic factors, the concentrated nature of drilling activities from hydraulic fracturing and horizontal drilling operations on MWP suggests that MWP may create less surface disturbance, produce more volumes of wastewater, and generate more environmental violations than SWP. To explore these hypotheses, we use geospatial techniques and statistical analyses (i.e., regression and Mann-Whitney tests) to assess development of unconventional shale gas wells, and quantify environmental violations and wastewater volumes on SWP and MWP in Pennsylvania. The analyses include assessments of the influence of different types of well pads on potential, minor and major environmental events. Results reveal that (a) in recent years, a majority of pads on which new wells for unconventional gas were drilled are MWP, (b) on average, MWP have about five wells located on each pad and thus, had the transition to MWP not occurred, between two and four times as much land surface disturbance would have occurred per year if drilling was relegated to SWP, (c) there were more environmental violations on MWP than SWP, but when the number of wells were taken into account, fewer environmental violations per well were observed on MWP than on SWP, (d) there were more wastewater and recycled wastewater volumes per pad and per well produced on MWP than on SWP, and (e) the proportion of wastewater that was recycled was higher on MWP than SWP. This study sheds light on how the evolution from SWP to MWP has influenced environmental violations and wastewater production

  20. Extreme positive allometry of animal adhesive pads and the size limits of adhesion-based climbing

    PubMed Central

    Labonte, David; Clemente, Christofer J.; Dittrich, Alex; Kuo, Chi-Yun; Crosby, Alfred J.; Irschick, Duncan J.; Federle, Walter

    2016-01-01

    Organismal functions are size-dependent whenever body surfaces supply body volumes. Larger organisms can develop strongly folded internal surfaces for enhanced diffusion, but in many cases areas cannot be folded so that their enlargement is constrained by anatomy, presenting a problem for larger animals. Here, we study the allometry of adhesive pad area in 225 climbing animal species, covering more than seven orders of magnitude in weight. Across all taxa, adhesive pad area showed extreme positive allometry and scaled with weight, implying a 200-fold increase of relative pad area from mites to geckos. However, allometric scaling coefficients for pad area systematically decreased with taxonomic level and were close to isometry when evolutionary history was accounted for, indicating that the substantial anatomical changes required to achieve this increase in relative pad area are limited by phylogenetic constraints. Using a comparative phylogenetic approach, we found that the departure from isometry is almost exclusively caused by large differences in size-corrected pad area between arthropods and vertebrates. To mitigate the expected decrease of weight-specific adhesion within closely related taxa where pad area scaled close to isometry, data for several taxa suggest that the pads’ adhesive strength increased for larger animals. The combination of adjustments in relative pad area for distantly related taxa and changes in adhesive strength for closely related groups helps explain how climbing with adhesive pads has evolved in animals varying over seven orders of magnitude in body weight. Our results illustrate the size limits of adhesion-based climbing, with profound implications for large-scale bio-inspired adhesives. PMID:26787862

  1. Functional Role of Dimerization of Human Peptidylarginine Deiminase 4 (PAD4)

    PubMed Central

    Liu, Yi-Liang; Chiang, Yu-Hsiu; Liu, Guang-Yaw; Hung, Hui-Chih

    2011-01-01

    Peptidylarginine deiminase 4 (PAD4) is a homodimeric enzyme that catalyzes Ca2+-dependent protein citrullination, which results in the conversion of arginine to citrulline. This paper demonstrates the functional role of dimerization in the regulation of PAD4 activity. To address this question, we created a series of dimer interface mutants of PAD4. The residues Arg8, Tyr237, Asp273, Glu281, Tyr435, Arg544 and Asp547, which are located at the dimer interface, were mutated to disturb the dimer organization of PAD4. Sedimentation velocity experiments were performed to investigate the changes in the quaternary structures and the dissociation constants (Kd) between wild-type and mutant PAD4 monomers and dimers. The kinetic data indicated that disrupting the dimer interface of the enzyme decreases its enzymatic activity and calcium-binding cooperativity. The Kd values of some PAD4 mutants were much higher than that of the wild-type (WT) protein (0.45 µM) and were concomitant with lower kcat values than that of WT (13.4 s−1). The Kd values of the monomeric PAD4 mutants ranged from 16.8 to 45.6 µM, and the kcat values of the monomeric mutants ranged from 3.3 to 7.3 s−1. The kcat values of these interface mutants decreased as the Kd values increased, which suggests that the dissociation of dimers to monomers considerably influences the activity of the enzyme. Although dissociation of the enzyme reduces the activity of the enzyme, monomeric PAD4 is still active but does not display cooperative calcium binding. The ionic interaction between Arg8 and Asp547 and the Tyr435-mediated hydrophobic interaction are determinants of PAD4 dimer formation. PMID:21731701

  2. Photoactivated disinfection (PAD) of dental root canal system – An ex-vivo study

    PubMed Central

    Mohan, Dennis; Maruthingal, Sunith; Indira, Rajamani; Divakar, Darshan Devang; Al Kheraif, Abdulaziz Abdullah; Ramakrishnaiah, Ravikumar; Durgesh, B.H.; Basavarajappa, Santhosh; John, Jacob

    2015-01-01

    Aim To investigate the efficacy of photo activated disinfection (PAD) in reducing colony-forming unit (CFU) counts of Enterococcus faecalis (E. faecalis) in infected dental root canals. The study compared the efficacy of PAD with conventional endodontic treatment (CET) and also a combination of CET along with PAD. Material and Methods 53 maxillary incisors were taken for the study. Teeth were divided into 3 groups, CET (Group I) (n = 11), PAD (Group II) (n = 21), and a combination of CET and PAD (Group III) which consisted of (n = 21) samples, Group II and Group III were further divided into 2 subgroups, Group IIa, IIb and Group IIIa, IIIb. Strains of E. faecalis were inoculated in all the root canals. CET group samples were treated by chemo-mechanical preparation (CMP) alone, PAD samples were treated with laser alone at 2 different exposure time (4 min and 2 min). In the combination treatment, samples were treated initially by CET and then by PAD for a time period of 4 min and 2 min. Contents of the root canal were aspirated, diluted and plated in Tryptone Soya Broth (TSB) and plates were incubated for 24 h to observe the bacterial regrowth. Results Showed PAD used along with CMP reduced the bacterial load of E. faecalis by 99.5% at 4 min and 98.89% at 2 min. Conclusion PAD may be an adjunctive procedure to kill residual bacteria in the dental root canal systems after standard endodontic root canal preparation. PMID:26858548

  3. Stretchable touch-sensing skin over padding for co-robots

    NASA Astrophysics Data System (ADS)

    Chen, Ying; Yu, Miao; Bruck, Hugh A.; Smela, Elisabeth

    2016-05-01

    For robots that work collaboratively with people, often referred to as ‘co-robots’, it would be beneficial for them to be soft or padded and to have a touch-sensing ‘skin’ to enable tactile environmental awareness. However, a sensing skin over a padding material that undergoes large deformations requires ‘stretchable’ materials, which may possess time-dependent or viscoelastic mechanical responses. In this work the roles that a padding layer plays when placed under a stretchable sensing layer was investigated. A strain-sensing skin was formed by coating a thin film of compliant piezoresistive sensing paint, consisting of exfoliated graphite in latex, onto a rubber membrane, and the response of the skin was characterized. The change in resistance was linear with tensile strain. The role of the padding material was then investigated under indentation by examining three foams and two elastomers. As expected, the padding enhanced energy dissipation as shown by hysteresis in the sensor response, which is linked to its protective function; the hysteresis was comparable for the five padding materials. The padding also provided an unexpected advantage: it magnified the change in resistance compared to that obtained under free displacement in air. While hysteresis in viscoelastic materials can largely be handled with an appropriate model, inconsistency cannot be, and the two elastomers were found to have unacceptably high variability because of micro-cracks and other defects in these materials. On the other hand, foams that had few defects and regular cell sizes gave good consistency across trials and different sensor positions over the padding. Combined with their lighter weight and availability in a wide range of stiffness, we conclude that foams make a better choice for padding of co-robots.

  4. Historical Material Analysis of DC745U Pressure Pads

    SciTech Connect

    Ortiz-Acosta, Denisse

    2012-07-30

    As part of the Enhance Surveillance mission, it is the goal to provide suitable lifetime assessment of stockpile materials. This report is an accumulation of historical publication on the DC745U material and their findings. It is the intention that the B61 LEP program uses this collection of data to further develop their understanding and potential areas of study. DC745U is a commercially available silicone elastomer consisting of dimethyl, methyl-phenyl, and methyl-vinyl siloxane repeat units. Originally, this material was manufactured by Dow Corning as Silastic{reg_sign} DC745U at their manufacturing facility in Kendallville, IN. Recently, Dow Corning shifted this material to the Xiameter{reg_sign} brand product line. Currently, DC745U is available through Xiameter{reg_sign} or Dow Corning's distributor R. D. Abbott Company. DC745U is cured using 0.5 wt% vinyl-specific peroxide curing agent known as Luperox 101 or Varox DBPH-50. This silicone elastomer is used in numerous parts, including two major components (outer pressure pads and aft cap support) in the W80 and as pressure pads on the B61. DC745U is a proprietary formulation, thus Dow Corning provides limited information on its composition and properties. Based on past experience with Dow Corning, DC745U is at risk of formulation changes without notification to the costumer. A formulation change for DC745U may have a significant impact because the network structure is a key variable in determining material properties. The purpose of this report is to provide an overview of historical DC745U studies and identify gaps that need to be addressed in future work. Some of the previous studies include the following: 1. Spectroscopic characterization of raw gum stock. 2. Spectroscopic, thermal, and mechanical studies on cured DC745U. 3. Nuclear Magnetic Resonance (NMR) and solvent swelling studies on DC745U with different crosslink densities. 4. NMR, solvent swelling, thermal, and mechanical studies on thermally aged

  5. A hinged-pad test structure for sliding friction measurement in micromachining

    SciTech Connect

    Boer, M.P. de; Redmond, J.M.; Michalske, T.A.

    1998-08-01

    The authors describe the design, modeling, fabrication and initial testing of a new test structure for friction measurement in MEMS. The device consists of a cantilevered forked beam and a friction pad attached via a hinge. Compared to previous test structures, the proposed structure can measure friction over much larger pressure ranges, yet occupies one hundred times less area. The placement of the hinge is crucial to obtaining a well-known and constant pressure distribution in the device. Static deflections on the device were measured and modeled numerically, Preliminary results indicate that friction pad slip is sensitive to friction pad normal force.

  6. Single Electron Detection in Quadruple-GEM Detector with Pad Readout

    SciTech Connect

    Va'vra, Jaroslav

    2001-03-07

    Using a system of four GEMs operating in tandem and coupled to pad readout, we have demonstrated the detection of single electrons in ethane at 1 bar. The paper presents measurements of single electron pulse height distributions, total gas gain measurement and calculation, pad-to-pad cross-talk, quenching capability, high rate capability, charging effects, etc. We describe the overall operational experience, including addition of a gaseous photocathode, TMAE, and compare it to the SLD CRID single-electron detector [1], which has been operational during the past decade.

  7. Velvet pad surface sampling of anaerobic and aerobic bacteria: an in vitro laboratory model.

    PubMed Central

    Raahave, D; Friis-Møller, A

    1982-01-01

    Velvet pads have been evaluated in an experimental, laboratory model, simulating intraoperative sampling of Staphylococcus epidermis, Escherichia coli and Bacteroides fragilis. After sampling, the pad was placed in a transport medium and kept in an anaerobic atmosphere, before being shaken and rinsed, followed by anaerobic and aerobic culture. This technique permitted quantitatively high recoveries of the test bacteria. Velvet pad sampling could be a measure to determine the density of aerobic and anaerobic bacteria during operation in an effort to predict the risk of postoperative wound sepsis. Images PMID:6757273

  8. Aerial view of the newest bus stop to view Launch Pad 39B

    NASA Technical Reports Server (NTRS)

    1998-01-01

    This aerial view looking northeast shows a new stop (bottom) on the KSC bus tour that allow visitors to view Pad LC-39B (top). The tour stop is next to the crawlerway that is used to transport the Space Shuttle vehicles to the pad. The length of the crawlerway from the Vehicle Assembly Building to Pad B is 6,828 meters (22,440 ft); its width overall is 40 meters (130 ft); each lane is 12 meters (40ft) with a 15-meter (50ft) median.

  9. Aerial view of the newest bus stop to view Launch Pad 39B

    NASA Technical Reports Server (NTRS)

    1998-01-01

    Tour buses unload passengers at a new stop on the KSC tour that allows visitors to view Pad LC-39B. The tour road runs parallel to the crawlerway (just out of sight) that is used to transport the Space Shuttle vehicles to the pad. The length of the crawlerway from the Vehicle Assembly Building to Pad B is 6,828 meters (22,440 ft); its width overall is 40 meters (130 ft); each lane is 12 meters (40ft) with a 15-meter (50ft) median. This view looks south.

  10. Experimental study of tilting-pad journal bearings - Comparison with theoretical thermoelastohydrodynamic results

    NASA Astrophysics Data System (ADS)

    Fillon, Michel; Bligoud, Jean-Claude; Frene, Jean

    1992-07-01

    Operating characteristics of four-shoe tilting-pad journal bearings of 100 mm diameter and 70 mm length are determined on an experimental device. The load, between pad configuration, varies from 0 to 10,000 N and the rotational speed is up to 4000 rpm. Forty thermocouples are used in order to measure bearing element temperatures (babbitt, shaft, housing and oil baths). The influence of operating conditions and preload ratio on bearing performances are studied. Comparison between theoretical and experimental results is presented. The theoretical model is also performed on a large tilting-pad journal bearing which was investigated experimentally by other authors.

  11. Field emission in actuation pads of radio frequency microelectromechanical systems ohmic switches: A potential contamination mechanism

    NASA Astrophysics Data System (ADS)

    Koutsoureli, M.; Reig, B.; Papandreou, E.; Poulain, C.; Souchon, F.; Deborgies, F.; Papaioannou, G.

    2016-01-01

    The field emission current generated across the actuation pads in ohmic MEMS switches during ON state is shown to constitute an additional source of degradation. Switches with Au/Au and Au/Ru contacts have been subjected to 24 h continuous stress. In both cases the switch ohmic contact resistance and field emission current across actuation pads were monitored simultaneously. The experimental results revealed a negligible degradation in Au/Au contact devices while the Au/Ru contact devices show a fast degradation. The experimental results from Au/Au and Ru/Au contact switches have been compared taking into account the plasma generation in the actuation pads.

  12. ATLANTIS ROLLS OUT TO PAD 39A FOLLOWING HURRICANE FRAN THREAT

    NASA Technical Reports Server (NTRS)

    1996-01-01

    The Space Shuttle Atlantis completes the trip to Launch Pad 39A from the Vehicle Assembly Building for the third time in the STS- 79 mission flow. The Shuttle was rolled back from the pad in July due to the threat from Hurricane Bertha, then rolled back again earlier this week because of Hurricane Fran. The targeted launch date for Atlantis on Mission STS-79 -- the fourth docking between the U.S. Shuttle and Russian Space Station Mir -- is now Sept. 16 at 4:54 a.m. EDT. The three rollout dates for Atlantis to Pad 39A are: July 1, Aug. 20 and Sept. 5.

  13. Mobile Tech and the Librarian: The iTest iPad Project

    PubMed Central

    Hamasu, Claire; Bramble, John

    2015-01-01

    A 2012 project provided forty-eight health sciences librarians from primarily hospital and academic health sciences libraries with an Apple iPad2 along with training and support on its use. Project objectives were to determine how participants would adopt the iPad into their daily operations and what form of leadership role they would play while participating in the project. By project's end eighty-nine percent indicated they would continue using the iPad primarily as a productivity tool and to provide point of need services. Project data indicated that librarians assumed a leadership role promoting the use of mobile technology and the applications available. PMID:26997921

  14. The iPad and EFL Digital Literacy

    NASA Astrophysics Data System (ADS)

    Meurant, Robert C.

    In future, the uses of English by non-native speakers will predominantly be online, using English language digital resources, and in computer-mediated communication with other non-native speakers of English. Thus for Korea to be competitive in the global economy, its EFL should develop L2 Digital Literacy in English. With its fast Internet connections, Korea is the most wired nation on Earth; but ICT facilities in educational institutions need reorganization. Opportunities for computer-mediated second language learning need to be increased, providing multimedia-capable, mobile web solutions that put the Internet into the hands of all students and teachers. Wi-Fi networked campuses allow any campus space to act as a wireless classroom. Every classroom should have a teacher's computer console. All students should be provided with adequate computing facilities, that are available anywhere, anytime. Ubiquitous computing has now become feasible by providing every student on enrollment with a tablet: a Wi-Fi+3G enabled Apple iPad.

  15. STS-79 LIFTS OFF FROM PAD 39A

    NASA Technical Reports Server (NTRS)

    1996-01-01

    The race to catch up with the Russian Space Station Mir begins with the on-time liftoff of the Space Shuttle Atlantis from Launch Pad 39A at 4:54:49 a.m. EDT, Sept. 16. The 10- day flight of Atlantis on Mission STS-79 will be highlighted by the fourth docking between the U.S. Space Shuttle and Russian Space Station Mir and the first in a series of crew exchanges aboard the station. On board Atlantis for the uphill leg of the trip are: Commander William F. Readdy; Pilot Terrence W. Wilcutt; and Mission Specialists Jay Apt, Thomas D. Akers, Carl E. Walz and John E. Blaha. Blaha will exchange places on Mir with U.S. astronaut Shannon W. Lucid, who will return to Earth with the STS-79 flight crew after a record-setting stay on the Russian station. STS-79 is the second Shuttle- Mir mission to carry a SPACEHAB module on board and the first to carry a double module. The STS-79 mission is part of the NASA/Mir program which is now into the Phase 1B portion, consisting of nine Shuttle-Mir docking flights and seven long-duration flights of U.S. astronauts aboard the station between early 1996 and late 1998.

  16. Finite element analysis of heel pad with insoles.

    PubMed

    Luo, Gangming; Houston, Vern L; Garbarini, Mary Anne; Beattie, Aaron C; Thongpop, Chaiya

    2011-05-17

    To design optimal insoles for reduction of pedal tissue trauma, experimental measurements and computational analyses were performed. To characterize the mechanical properties of the tissues, indentation tests were performed. Pedal tissue geometry and morphology were obtained from magnetic resonance scan of the subject's foot. Axisymmetrical finite element models of the heel of the foot were created with 1/4 of body weight load applied. The stress, strain and strain energy density (SED) fields produced in the pedal tissues were computed. The effects of various insole designs and materials on the resulting stress, strain, and SED in the soft pedal tissues were analyzed. The results showed: (a) Flat insoles made of soft material provide some reductions in the maximum stress, strain and SED produced in the pedal tissues. These maximum values were computed near the calcaneus. (b) Flat insoles, with conical/cylindrical reliefs, provided more reductions in these maximum values than without reliefs. (c) Custom insoles, contoured to match the pedal geometry provide most reductions in the maximum stress, strain and SED. Also note, the maximum stress, strain and SED computed near the calcaneus were found to be about 10 times the corresponding peak values computed on the skin surface. Based on the FEA analysis, it can be concluded that changing insole design and using different material can significantly redistribute the stress/strain inside the heel pad as well as on the skin surface. PMID:21420682

  17. STS-111 Endeavour rollout to Launch Pad 39-A

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. - Space Shuttle Endeavour rests on Launch Pad 39A after rollout from the Vehicle Assembly Building. The Shuttle comprises the orbiter, in front, and the taller orange external tank behind it flanked by twin solid rocket boosters. The Shuttle sits on the Mobile Launcher Platform that straddles the flame trench below. On either side of Endeavour's tail and main engines are the tail service masts that support the fluid,, gas and electrical requirements of the orbiter's liquid oxyen and liquid hydrogen aft T-0 umbilicals. In the foreground, left, is the White Room, located at the end of the orbiter access arm. This environmentally controlled area provides access to the cockpit of the orbiter. Mission STS-111 is designated UF-2, the 14th assembly flight to the International Space Station. Endeavour's payload includes the Multi-Purpose Logistics Module Leonardo and Mobile Base System. The mission also will swap resident crews on the Station, carrying the Expedition 5 crew and returning to Earth Expedition 4. Liftoff of Endeavour is scheduled between 4 and 8 p.m. May 30, 2002.

  18. STS-111 Endeavour rollout to Launch Pad 39-A

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- Space Shuttle Endeavour rests on Launch Pad 39A after rollout from the Vehicle Assembly Building. The Shuttle comprises the orbiter, in front, and the taller orange external tank behind it flanked by twin solid rocket boosters. The Shuttle sits on the Mobile Launcher Platform that straddles the flame trench below. On either side of Endeavour's tail and main engines are the tail service masts that support the fluid,, gas and electrical requirements of the orbiter's liquid oxyen and liquid hydrogen aft T-0 umbilicals. At left is the open Rotating Service Structure and the Fixed Service Structure to its right, with its 80-foot lightning mast on top. Mission STS-111 is designated UF-2, the 14th assembly flight to the International Space Station. Endeavour's payload includes the Multi-Purpose Logistics Module Leonardo and Mobile Base System. The mission also will swap resident crews on the Station, carrying the Expedition 5 crew and returning to Earth Expedition 4. Liftoff of Endeavour is scheduled between 4 and 8 p.m. May 30, 2002.

  19. STS-110 Atlantis rolls out to Launch Pad 39-A

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. - Viewed from across the turn basin, Space Shuttle Atlantis stands out in the bright morning light as it makes its way to the launch pad. The Shuttle sits atop the Mobile Launcher Platform, which in turn rests on the crawler-transporter beneath it, moving about 1 mile per hour. Atlantis is scheduled for launch April 4 on mission STS-110, which will install the S0 truss, the framework that eventually will hold the power and cooling systems needed for future international research laboratories on the International Space Station. The Canadarm2 robotic arm will be used exclusively to hoist the 13-ton truss from the payload bay to the Station. The S0 truss will be the first major U.S. component launched to the Station since the addition of the Quest airlock in July 2001. The four spacewalks planned for the construction will all originate from the airlock. The mission will be Atlantis' 25th trip to space.

  20. STS-110 Atlantis rolls out to Launch Pad 39-A

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- Space Shuttle Atlantis is hard down on the launch pad after its mid-day rollout from the Vehicle Assembly Building. Part of the Fixed Service Structure is at left. On either side of the tail of Atlantis are the tail service masts, which support the fluid, gas and electrical requirements of the orbiter's liquid oxygen and liquid hydrogen aft T-0 umbilicals. Atlantis is scheduled for launch April 4 on mission STS-110, which will install the S0 truss, the framework that eventually will hold the power and cooling systems needed for future international research laboratories on the International Space Station. The Canadarm2 robotic arm will be used exclusively to hoist the 13-ton truss from the payload bay to the Station. The S0 truss will be the first major U.S. component launched to the Station since the addition of the Quest airlock in July 2001. The four spacewalks planned for the construction will all originate from the airlock. The mission will be Atlantis' 25th trip to space.

  1. STS-110 Atlantis rolls out to Launch Pad 39-A

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- Its immense size dwarfing the van driving in front of it, Space Shuttle Atlantis inches toward the launch pad. Both the Rotating Service Structure (open) and the Fixed Service Structure, which holds the 80-foot lightning mast on top, are seen at right. The Shuttle sits on top of the Mobile Launcher Platform, which rests on the crawler-transporter. Atlantis is scheduled for launch April 4 on mission STS-110, which will install the S0 truss, the framework that eventually will h old the power and cooling systems needed for future international research laboratories on the International Space Station. The Canadarm2 robotic arm will be used exclusively to hoist the 13-ton truss from the payload bay to the Station. The S0 truss will be the first major U.S. component launched to the Station since the addition of the Quest airlock in July 2001. The four spacewalks planned for the construction will all originate from the airlock. The mission will be Atlantis' 25th trip to space.

  2. STS-110 Atlantis rolls out to Launch Pad 39-A

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- Space Shuttle Atlantis reaches the top of the launch pad after a mid-day rollout from the Vehicle Assembly Building. Next to the Shuttle are the Rotating Service Structure (open) and the Fixed Service Structure, which holds the 80-foot lightning mast on top. The Shuttle sits on top of the Mobile Launcher Platform, which rests on the crawler-transporter. Atlantis is scheduled for launch April 4 on mission STS-110, which will install the S0 truss, the framework that eventually will hold the power and cooling systems needed for future international research laboratories on the International Space Station. The Canadarm2 robotic arm will be used exclusively to hoist the 13-ton truss from the payload bay to the Station. The S0 truss will be the first major U.S. component launched to the Station since the addition of the Quest airlock in July 2001. The four spacewalks planned for the construction will all originate from the airlock. The mission will be Atlantis' 25th trip to space.

  3. STS-97 Space Shuttle Endeavour on Launch Pad 39B

    NASA Technical Reports Server (NTRS)

    2000-01-01

    Space Shuttle Endeavour waits on Launch Pad 39B for launch on mission STS-97. Behind it are the orange external tank flanked by two solid rocket boosters. On either side of Endeavour'''s tail are the tail service masts, which support the fluid, gas and electrical requirements of the orbiter'''s liquid oxygen and liquid hydrogen aft T-0 umbilicals. The masts also protect the ground half of those umbilicals from the harsh launch environment. At launch, the masts rotate backward, triggering a compressed-gas thruster and causing a protective hood to move into place and completely seal the structure from the main engine exhaust. At the end of the orbiter access arm, near the nose of Endeavour, is the White Room, an environmental chamber that provides both entrance to the orbiter and emergency egress, if needed. The arm remains extended until 7 minutes, 24 seconds before launch. The arm extends from the Fixed Service Structure. In the center of Endeavour are the payload bay doors. Endeavour is scheduled to launch Nov. 30 at 10:06 p.m. EST.

  4. Space Shuttle Atlantis is on Launch Pad 39B

    NASA Technical Reports Server (NTRS)

    2001-01-01

    KENNEDY SPACE CENTER, Fla. -- Atop the mobile launcher platform, Space Shuttle Atlantis sits on Launch Pad 39B after rollout from the Vehicle Assembly Building. Seen on either side of the orbiters tail are the tail service masts. They support the fluid, gas and electrical requirements of the orbiters liquid oxygen and liquid hydrogen aft umbilicals. To the left of the orbiter is the white environmental chamber (white room) that mates with the orbiter and holds six persons. It provides access to the orbiter crew compartment. In the background is the Atlantic Ocean. The Shuttle is targeted for launch no earlier than July 12 on mission STS-104, the 10th flight to the International Space Station. The payload on the 11-day mission is the Joint Airlock Module, which will allow astronauts and cosmonauts in residence on the Station to perform future spacewalks without the presence of a Space Shuttle. The module, which comprises a crew lock and an equipment lock, will be connected to the starboard (right) side of Node 1 Unity. Atlantis will also carry oxygen and nitrogen storage tanks, vital to operation of the Joint Airlock, on a Spacelab Logistics Double Pallet in the payload bay. The tanks, to be installed on the perimeter of the Joint Module during the missions spacewalks, will support future spacewalk operations and experiments plus augment the resupply system for the Stations Service Module.

  5. Space Shuttle Atlantis is on Launch Pad 39B

    NASA Technical Reports Server (NTRS)

    2001-01-01

    KENNEDY SPACE CENTER, Fla. -- Atop the mobile launcher platform, Space Shuttle Atlantis, with its orange external tank and white solid rocket boosters, sits on Launch Pad 39B after rollout from the Vehicle Assembly Building. Seen on either side of the orbiters tail are the tail service masts. They support the fluid, gas and electrical requirements of the orbiters liquid oxygen and liquid hydrogen aft umbilicals. The Shuttle is targeted for launch no earlier than July 12 on mission STS-104, the 10th flight to the International Space Station. The payload on the 11- day mission is the Joint Airlock Module, which will allow astronauts and cosmonauts in residence on the Station to perform future spacewalks without the presence of a Space Shuttle. The module, which comprises a crew lock and an equipment lock, will be connected to the starboard (right) side of Node 1 Unity. Atlantis will also carry oxygen and nitrogen storage tanks, vital to operation of the Joint Airlock, on a Spacelab Logistics Double Pallet in the payload bay. The tanks, to be installed on the perimeter of the Joint Module during the missions spacewalks, will support future spacewalk operations and experiments plus augment the resupply system for the Stations Service Module.

  6. STS-103 payload canister arrives at Launch Pad 39B

    NASA Technical Reports Server (NTRS)

    1999-01-01

    At Launch Pad 39B, the payload canister for Space Shuttle Discovery, for mission STS-103, is lifted up the Rotating Service Structure. The umbilicals attached to the canister provide an environmental control system until transfer to the orbiter. Installation of the payload into Discovery is slated for Friday, Nov. 12. The mission is a 'call-up' due to the need to replace portions of the pointing system, the gyros, which have begun to fail on the Hubble Space Telescope. Although Hubble is operating normally and conducting its scientific observations, only three of its six gyroscopes are working properly. The gyroscopes allow the telescope to point at stars, galaxies and planets. The STS-103 crew will also be replacing a Fine Guidance Sensor and an older computer with a new enhanced model, an older data tape recorder with a solid-state digital recorder, a failed spare transmitter with a new one, and degraded insulation on the telescope with new thermal insulation. The crew will also install a Battery Voltage/Temperature Improvement Kit to protect the spacecraft batteries from overcharging and overheating when the telescope goes into a safe mode.

  7. Space Shuttle Atlantis is on Launch Pad 39B

    NASA Technical Reports Server (NTRS)

    2001-01-01

    KENNEDY SPACE CENTER, Fla. -- Atop the mobile launcher platform, Space Shuttle Atlantis arrives on Launch Pad 39B after rollout from the Vehicle Assembly Building. Seen on either side of the orbiters tail are the tail service masts. They support the fluid, gas and electrical requirements of the orbiters liquid oxygen and liquid hydrogen aft umbilicals. The Shuttle is targeted for launch no earlier than July 12 on mission STS-104, the 10th flight to the International Space Station. The payload on the 11- day mission is the Joint Airlock Module, which will allow astronauts and cosmonauts in residence on the Station to perform future spacewalks without the presence of a Space Shuttle. The module, which comprises a crew lock and an equipment lock, will be connected to the starboard (right) side of Node 1 Unity. Atlantis will also carry oxygen and nitrogen storage tanks, vital to operation of the Joint Airlock, on a Spacelab Logistics Double Pallet in the payload bay. The tanks, to be installed on the perimeter of the Joint Module during the missions spacewalks, will support future spacewalk operations and experiments plus augment the resupply system for the Stations Service Module.

  8. STS-79 LIFTS OFF FROM PAD 39A

    NASA Technical Reports Server (NTRS)

    1996-01-01

    The Space Shuttle Atlantis roars into the night from Launch Pad 39A. Liftoff on the 79th Shuttle mission occurred on time at 4:54:49 a.m. EDT, Sept. 16. The 10-day spaceflight will be highlighted by the fourth docking between the U.S. Space Shuttle and Russian Space Station Mir and the first in a series of crew exchanges aboard the station. Leading the STS-79 crew is Commander William F. Readdy. The pilot is Terrence W. Wilcutt, and the four mission specialists making the trip to Mir are Jay Apt, Thomas D. Akers, Carl E. Walz and John E. Blaha. Blaha will exchange places on Mir with U.S. astronaut Shannon W. Lucid, who will return to Earth with the STS-79 flight crew after a record- setting stay on the Russian station. STS-79 is the second Shuttle-Mir mission to carry a SPACEHAB module on board and the first to carry a double module. The STS- 79 mission is part of the NASA/Mir program which is now into the Phase 1B portion, consisting of nine Shuttle-Mir docking flights and seven long- duration flights of U.S. astronauts aboard the station between early 1996 and late 1998.

  9. STS-110 Atlantis rolls out to Launch Pad 39-A

    NASA Technical Reports Server (NTRS)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- In the foreground, white herons at the canal's edge pay scant attention the immense Space Shuttle towering above them. The Shuttle is inching its way to the top of the launch pad. In the background are seen the Rotating Service Structure (open) and the Fixed Service Structure, which holds the 80-foot lightning mast on top. The Shuttle sits on top of the Mobile Launcher Platform, which rests on the crawler-transporter. Atlantis is scheduled for launch April 4 on mission STS-110, which will install the S0 truss, the framework that eventually will hold the power and cooling systems needed for future international research laboratories on the International Space Station. The Canadarm2 robotic arm will be used exclusively to hoist the 13-ton truss from the payload bay to the Station. The S0 truss will be the first major U.S. component launched to the Station since the addition of the Quest airlock in July 2001. The four spacewalks planned for the construction will all originate from the airlock. The mission will be Atlantis' 25th trip to space.

  10. Encapsulated Thermoelectric Modules and Compliant Pads for Advanced Thermoelectric Systems

    NASA Astrophysics Data System (ADS)

    Kambe, Mitsuru; Jinushi, Takahiro; Ishijima, Zenzo

    2010-09-01

    The described encapsulated thermoelectric (TE) module consists of a vacuum-tight stainless-steel container with dimensions of 55 mm × 50 mm × 11 mm in which a SiGe or BiTe TE module is placed. This construction enables maximum performance and durability because: (1) the thermal expansion mismatch between the hot and cold sides of the container can be accommodated by a sliding sheet that is present in the container; (2) the TE module inside is always kept in a vacuum environment so that oxidation cannot occur; and (3) the difference in pressure between the inside and outside of the container reduces the thermal contact resistance inside the container. The design also includes a compliant pad made of porous material that is infiltrated with braze filler material. If heated to a temperature above the melting temperature of the braze filler, the thermal gap conductance of the interface is enhanced due to the strong affinity of the braze filler to an adjacent member. It is possible for this interface to slide as long as the braze filler is in the liquid state. This design strategy provides high-flux, direct conduction paths to the heat source and heat sink as well as a large temperature gradient across the TE module itself (1.7 times that in the case of the conventional design strategy); therefore, the module can provide a power output that is three times greater than that of a conventional module.

  11. STS-91 Launch of Discovery from Launch Pad 39-A

    NASA Technical Reports Server (NTRS)

    1998-01-01

    The last mission of the Shuttle-Mir program begins as the Space Shuttle Discovery lifts off from Launch Pad 39A at 6:06:24 p.m. EDT June 2. A torrent of water is seen flowing onto the mobile launcher platform (MLP) from numerous large quench nozzles, or 'rainbirds,' mounted on its surface. This water, part of the Sound Suppression System, helps protect the orbiter and its payloads from damage by acoustical energy and rocket exhaust reflected from the flame trench and MLP during launch. On board Discovery are Mission Commander Charles J. Precourt; Pilot Dominic L. Gorie; and Mission Specialists Wendy B. Lawrence, Franklin R. Chang-Diaz, Janet Lynn Kavandi and Valery Victorovitch Ryumin. The nearly 10-day mission will feature the ninth and final Shuttle docking with the Russian space station Mir, the first Mir docking for the Space Shuttle orbiter Discovery, the first on-orbit test of the Alpha Magnetic Spectrometer (AMS), and the first flight of the new Space Shuttle super lightweight external tank. Astronaut Andrew S. W. Thomas will be returning to Earth as an STS-91 crew member after living more than four months aboard Mir.

  12. Towards reducing impact-induced brain injury: lessons from a computational study of army and football helmet pads.

    PubMed

    Moss, William C; King, Michael J; Blackman, Eric G

    2014-01-01

    We use computational simulations to compare the impact response of different football and U.S. Army helmet pad materials. We conduct experiments to characterise the material response of different helmet pads. We simulate experimental helmet impact tests performed by the U.S. Army to validate our methods. We then simulate a cylindrical impactor striking different pads. The acceleration history of the impactor is used to calculate the head injury criterion for each pad. We conduct sensitivity studies exploring the effects of pad composition, geometry and material stiffness. We find that (1) the football pad materials do not outperform the currently used military pad material in militarily relevant impact scenarios; (2) optimal material properties for a pad depend on impact energy and (3) thicker pads perform better at all velocities. Although we considered only the isolated response of pad materials, not entire helmet systems, our analysis suggests that by using larger helmet shells with correspondingly thicker pads, impact-induced traumatic brain injury may be reduced. PMID:23244512

  13. Study of the factors that promoted the implementation of Electronic Medical Record on iPads at Two Emergency Departments

    PubMed Central

    Rao, Akhil Sanjay; Adam, Terrence J.; Gensinger, Raymond; Westra, Bonnie L.

    2012-01-01

    The purpose of this study was to understand the factors which promoted the demand for iPads by physicians in two Emergency departments (ED) prior to a system wide implementation of an electronic medical record (EMR). A grounded theory design was employed and 14 semi-structured interviews conducted with ED physicians. Analysis of the interview transcripts was completed using Atlas.ti qualitative software, which revealed that physicians’ perceptions of iPad use in the ED stemmed from their personal use of iPads along with three perceived ease of use factors. Physicians perceived that improved patient physician interaction, improved workflow and structural iPad benefits promoted their demand. Physicians perceived the structural benefits of iPads would improve patient physician interaction and improve workflow in the ED. As interest in handheld devices such as iPads increases, these findings could direct and encourage other iPad implementations at other hospital EDs’. PMID:23304348

  14. A generalized Padé approximation method of solving homoclinic and heteroclinic orbits of strongly nonlinear autonomous oscillators

    NASA Astrophysics Data System (ADS)

    Li, Zhen-Bo; Tang, Jia-Shi; Cai, Ping

    2014-12-01

    An intrinsic extension of Padé approximation method, called the generalized Padé approximation method, is proposed based on the classic Padé approximation theorem. According to the proposed method, the numerator and denominator of Padé approximant are extended from polynomial functions to a series composed of any kind of function, which means that the generalized Padé approximant is not limited to some forms, but can be constructed in different forms in solving different problems. Thus, many existing modifications of Padé approximation method can be considered to be the special cases of the proposed method. For solving homoclinic and heteroclinic orbits of strongly nonlinear autonomous oscillators, two novel kinds of generalized Padé approximants are constructed. Then, some examples are given to show the validity of the present method. To show the accuracy of the method, all solutions obtained in this paper are compared with those of the Runge—Kutta method.

  15. 9. Photocopy of engineering drawing. LC17 LOX STORAGE TANK PAD: ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    9. Photocopy of engineering drawing. LC-17 LOX STORAGE TANK PAD: ELECTRICAL, OCTOBER 1966. - Cape Canaveral Air Station, Launch Complex 17, Facility 28405, East end of Lighthouse Road, Cape Canaveral, Brevard County, FL

  16. The Feasibility of At-Home iPad Cognitive Testing For Use in Clinical Trials

    PubMed Central

    Rentz, Dorene M.; Dekhtyar, Maria; Sherman, Julia; Burnham, Samantha; Blacker, Deborah; Aghjayan, Sarah L.; Papp, Kathryn V.; Amariglio, Rebecca E.; Schembri, Adrian; Chenhall, Tanya; Maruff, Paul; Aisen, Paul; Hyman, Bradley T.; Sperling, Reisa A.

    2015-01-01

    Background Technological advances now make it feasible to administer cognitive assessments at-home on mobile and touch-screen devices such as an iPad or tablet computer. Validation of these techniques is necessary to assess their utility in clinical trials. Objectives We used a Computerized Cognitive Composite for Preclinical Alzheimer’s Disease (C3-PAD) developed for iPad 1) to determine the feasibility of performing the C3-PAD at home by older individuals without the presence of a trained psychometrician; 2) to explore the reliability of in-clinic compared to at-home C3-PAD performance and 3) to examine the comparability of C3-PAD performance to standardized neuropsychological tests. Design, Setting, Participants Forty-nine cognitively normal older individuals (mean age, 71.467.7 years; 20% non-Caucasian) were recruited from research centers at the Massachusetts General Hospital and Brigham and Women’s Hospital. Participants made two in-clinic visits one-week apart and took five 30-minute alternate versions of the C3-PAD at-home measuring episodic memory, reaction time and working memory. Measurements A reliability analysis explored equivalence of the six alternate C3-PAD test versions. A feasibility assessment calculated the percentage of individuals who completed all at-home tests correctly, in contrast to incomplete assessments. Correlational analyses examined the association between C3-PAD-clinic compared to C3-PAD-home assessments and between C3-PAD performance and standardized paper and pencil tests. Results Excellent reliability was observed among the 6 C3-PAD alternate versions (Cronbach alpha coefficient=0.93). A total of 28 of 49 participants completed all at-home sessions correctly and 48 of 49 completed four out of five correctly. There were no significant differences in participant age, sex or education between complete and incomplete at-home assessments. A single in-clinic C3-PAD assessment and the at-home C3-PAD assessments were highly

  17. Development of a hadron blind detector using a finely segmented pad readout

    NASA Astrophysics Data System (ADS)

    Kanno, Koki; Aoki, Kazuya; Aramaki, Yoki; En`yo, Hideto; Kawama, Daisuke; Komatsu, Yusuke; Masumoto, Shinichi; Nakai, Wataru; Obara, Yuki; Ozawa, Kyoichiro; Sekimoto, Michiko; Shibukawa, Takuya; Takahashi, Tomonori; Watanabe, Yosuke; Yokkaichi, Satoshi

    2016-05-01

    We constructed a hadron blind detector (HBD) using a finely segmented pad readout. The finely segmented pad readout enabled us to adopt an advanced particle identification method which applies a threshold to the number of pad hits in addition to the total amount of collected charge. The responses of the detector to electrons and pions were evaluated using a negatively charged secondary beam at 1.0 GeV/c containing 20% electrons at the J-PARC K1.1BR beam line. We observed 7.3 photoelectrons per incident electron. Using the advanced particle identification method, an electron detection efficiency of 83% was achieved with a pion rejection factor of 120. The method improved the pion rejection by approximately a factor of five, compared to the one which just applies a threshold to the amount of collected charge. The newly introduced finely segmented pad readout was found to be effective in rejecting pions.

  18. Ct Anatomy of Buccal Fat Pad and its Role in Volumetric Alterations of Face

    NASA Astrophysics Data System (ADS)

    Guryanov, R. A.; Guryanov, A. S.

    2015-05-01

    The aim of our study is the revision of the anatomy of buccal fat pad and its role in a volumetric pattern of face. Bichat fat pad is a fatty anatomical structure with body and numerous process enclosed between the bony and muscular structures in temporal, pterygopalatine fossae and extents to the cheek area. Nevertheless, the opinion about its structure and role in forming of volume pattern of face sometimes could be controversial. The Bichat fat pad consists on predominately hormone insensitive fat tissue with underdeveloped stroma, this leads to the stability of the fat pad volume and lesser radiodensity in contrast to the subcutaneous fat. Moreover, the buccal fat pad is delimited from the subcutaneous fat of cheek area by the strong capsule. This feature allows us to use CT to divide the Bichat fat pad from the surrounding tissues. The thorough embryological data provide the distinction of Bichat fat pad from the subcutaneous fat of cheek area even at the stage of development. On the other hand, the border between the masticatory muscles and the processes of the fat pad is not evident and resembles cellular spaces in the other anatomical areas. To elicit the role of the buccal fat pad in volume pattern of face and its function we have performed the several experiments, analyzed the postoperative results after Bichat fat pad resection using surface scanner and CT data. At first, we have performed the gravity test: the patient's face photogrammetry scanning in horizontal and vertical position of head and it revealed the excess of volume in temporal area in horizontal position. To exclude mechanism of overflowing of the skin and subcutaneous fat over the zygomatic arch we have placed the markers on the skin surface at the different areas of face including the projection of ligaments and found out that the migration of soft tissue over the zygomatic arch is about 3-5 mm and almost the same in temporal area. However, the acquired result was unsatisfying because

  19. Astronauts Stafford and Cernan leave Pad 19 after Gemini 9 mission postponed

    NASA Technical Reports Server (NTRS)

    1966-01-01

    Astronauts Thomas P. Stafford (left), command pilot, and Eugene A. Cernan, walk away from Pad 19 after Gemini 9 mission was postponed. Failure of the Agena Target Vehicle to achieve orbit caused the postponement of the mission.

  20. Astronaut James Lovell walks to elevator on Pad 19 before Gemini 7 launch

    NASA Technical Reports Server (NTRS)

    1965-01-01

    Astronaut James A. Lovell Jr., pilot of the Gemini 7 space flight, walks to the elevator at Pad 19 one hour and forty minutes before launch of the spacecraft. He is dressed in the new Gemini space suit.

  1. PHOTOGRAPHY BY KSC SPACE SHUTTLE ORBITER ENTERPRISE STANDS ON KSC'S PAD 39A HIGHLIGHTED AGAINST THE

    NASA Technical Reports Server (NTRS)

    1980-01-01

    PHOTOGRAPHY BY KSC SPACE SHUTTLE ORBITER ENTERPRISE STANDS ON KSC'S PAD 39A HIGHLIGHTED AGAINST THE DARKENED FLORIDA SKY DURING TESTING OF THE HIGH-INTENSITY LIGHTING SYSTMES. THE BANKS OF XENON LIGHTS ARE USED DURING LAUCH PREPARATIONS.

  2. Space Shuttle orbiter Challenger sits on the mobile launch pad for STS-6

    NASA Technical Reports Server (NTRS)

    1983-01-01

    Space Shuttle orbiter Challenger sits on the mobile launch platform at Pad 39A at the Kennedy Space Center awaiting preparations for the launch of STS-6. A payload canister is in the nearby rotating service structure (RSS).

  3. Rotordynamic characteristics of flexure-pivot tilting-pad journal bearings

    NASA Astrophysics Data System (ADS)

    Armentrout, Richard W.; Paquette, Donald J.

    1993-07-01

    Many of today's modern turbomachines, especially those running at high speeds and high power ratings, require the superior stability characteristics of tilting-pad journal bearings to prevent rotor-dynamic instabilities. Until now, the design complexity of tilting-pad bearings has precluded their use in many small, high-volume applications where cost and size are important. This paper introduces a new one-piece journal bearing design, the flexure-pivot bearing, that offers many of the beneficial rotor-dynamic advantages of tilting-pad bearings, without the complexities of a multi-piece design. Performance data for a flexure-pivot bearing is shown for an application requiring a highly stable design, illustrating the effectiveness of the flexure-pivot bearing in offering rotordynamic stability approaching that of a tilting-pad bearing.

  4. Precision Attitude Determination System (PADS) design and analysis. Two-axis gimbal star tracker

    NASA Technical Reports Server (NTRS)

    1973-01-01

    Development of the Precision Attitude Determination System (PADS) focused chiefly on the two-axis gimballed star tracker and electronics design improved from that of Precision Pointing Control System (PPCS), and application of the improved tracker for PADS at geosynchronous altitude. System design, system analysis, software design, and hardware design activities are reported. The system design encompasses the PADS configuration, system performance characteristics, component design summaries, and interface considerations. The PADS design and performance analysis includes error analysis, performance analysis via attitude determination simulation, and star tracker servo design analysis. The design of the star tracker and electronics are discussed. Sensor electronics schematics are included. A detailed characterization of the application software algorithms and computer requirements is provided.

  5. Analysis of Formation of Pad Stains in Copper Chemical Mechanical Planarization

    NASA Astrophysics Data System (ADS)

    Lee, Hyosang; Borucki, Leonard; Zhuang, Yun; Joh, Sooyun; O'Moore, Fergal; Philipossian, Ara

    2009-12-01

    A stain model was developed to simulate stain formation on the pad surface in copper chemical and mechanical planarization (CMP). The model consisted of the incompressible Navier-Stokes equations, the heat equation with advection, material removal rate model, a model for generation, transport and deposition of the polishing by-product that produces the stain. Slurry velocity simulations showed shear flow on the land areas and wafer-driven circulation in the grooves. The simulated temperature on the pad and the wafer surface increased gradually in the radial direction; furthermore, temperature simulations showed a 12 °C rise in the reaction temperature on the copper wafer surface. The simulated pad stains deposited on the copper land areas were darker in the direction of wafer rotation, suggesting that the generated staining agents were advected downstream by the slurry flow and deposited on the pad surface in the direction of the wafer rotation. Simulated stain images were in qualitative agreement with experimental results.

  6. Physicochemical characterization of cactus pads from Opuntia dillenii and Opuntia ficus indica.

    PubMed

    Méndez, Lorena Pérez; Flores, Fidel Tejera; Martín, Jacinto Darias; Rodríguez Rodríguez, Elena M; Díaz Romero, Carlos

    2015-12-01

    Physicochemical characteristics (weight, length, width, thickness, moisture, Brix degree, total fiber, protein, ash, pH, acidity, ascorbic acid, total phenolic compounds, P, Na, K, Ca, Mg, Fe, Cu, Zn, Mn and Cr) were determined in cactus pads from Opuntia dillenii and Opuntia ficus indica. The physicochemical characteristics of both species were clearly different. There were important differences between the orange and green fruit pulp of O. ficus indica; the cactus pads of O. dillenii could be differentiated according to the region (North and South). Consumption of cactus pads contributes to the intake of dietary fiber, total phenolic compounds, K, Mg, Mn and Cr. Applying factor and/or discriminant analysis, the cactus pad samples were clearly differentiated according to the species, the fruit pulp color and production region. PMID:26041209

  7. iPads: Intuitive Technology for 21st-Century Students

    ERIC Educational Resources Information Center

    Siegle, Del

    2013-01-01

    The purpose of this article is to provide a rationale for using iPad technology with young students. Various inexpensive apps are described that parents and educators will find useful. (Contains 9 figures.)

  8. ATLANTIS ROLLS OUT TO PAD 39A FOLLOWING HURRICANE FRAN THREAT

    NASA Technical Reports Server (NTRS)

    1996-01-01

    A view from the flame trench looking up shows the Space Shuttle Atlantis, mounted on the Mobile Launcher Platform and Crawler- Transporter, as it arrives atop the hardstand at Launch Pad 39A. After the Shuttle and launch stand are in position, the crawler will be pulled back. This is the third time Atlantis has completed the journey to Launch Pad 39A in the STS-79 mission flow. The Shuttle was rolled back from the pad in July due to the threat from Hurricane Bertha, then rolled back again earlier this week because of Hurricane Fran. The targeted launch date for Atlantis on Mission STS-79 -- the fourth docking between the U.S. Shuttle and Russian Space Station Mir -- is now Sept. 16 at 4:54 a.m. EDT. The three rollout dates for Atlantis to Pad 39A are: July 1, Aug. 20 and Sept. 5.

  9. Dependence of Measured Lateral Stress on Thickness of Protective ``Padding'' around Gauge

    NASA Astrophysics Data System (ADS)

    Hammond, R. I.; Church, P. D.; Grief, A.; Proud, W. G.; Field, J. E.

    2004-07-01

    Earlier work found that lateral stress gauges were unusable when the longitudinal stress in the sample exceeded around 13 GPa in samples of steel. This pressure corresponds to a phase transition found in iron and its alloys. It was hoped that protective padding would allow measurement of stresses higher than this. It was therefore necessary to investigate the effect of the padding on the stress measured. A series of experiments were carried out using mild steel with different thicknesses of mylar or polycarbonate padding. This research has been supported by simulation studies using the Eulerian hydrocode GRIM, which has indicated some issues with the representation of the lateral gauge in the hydrocode. The simulations have confirmed the experimental trends observed with additional padding, but they have also indicated the potential need for additional analysis on the raw lateral gauge data.

  10. Digital representation of oil and natural gas well pad scars in southwest Wyoming: 2012 update

    USGS Publications Warehouse

    Garman, Steven L.; McBeth, Jamie L.

    2015-01-01

    The recent proliferation of oil and natural gas energy development in the Greater Green River Basin of southwest Wyoming has accentuated the need to understand wildlife responses to this development. The location and extent of surface disturbance that is created by oil and natural gas well pad scars are key pieces of information used to assess the effects of energy infrastructure on wildlife populations and habitat. A digital database of oil and natural gas pad scars had previously been generated from 1-meter (m) National Agriculture Imagery Program imagery (NAIP) acquired in 2009 for a 7.7-million hectare (ha) (19,026,700 acres) region of southwest Wyoming. Scars included the pad area where wellheads, pumps, and storage facilities reside and the surrounding area that was scraped and denuded of vegetation during the establishment of the pad. Scars containing tanks, compressors, the storage of oil and gas related equipment, and produced-water ponds were also collected on occasion. This report updates the digital database for the five counties of southwest Wyoming (Carbon, Lincoln, Sublette, Sweetwater, Uinta) within the Wyoming Landscape Conservation Initiative (WLCI) study area and for a limited portion of Fremont, Natrona, and Albany Counties using 2012 1-m NAIP imagery and 2012 oil and natural gas well permit information. This report adds pad scars created since 2009, and updates attributes of all pad scars using the 2012 well permit information. These attributes include the origination year of the pad scar, the number of active and inactive wells on or near each pad scar in 2012, and the overall status of the pad scar (active or inactive). The new 2012 database contains 17,404 pad scars of which 15,532 are attributed as oil and natural gas well pads. Digital data are stored as shapefiles projected to the Universal Transverse Mercator (zones 12 and 13) coordinate system. These data are available from the U.S. Geological Survey (USGS) at http://dx.doi.org/10

  11. Closure of oroantral communications with Bichat´s buccal fat pad. Level of patient satisfaction

    PubMed Central

    Alonso-González, Rocío; Peñarrocha-Diago, María; Peñarrocha-Oltra, David; Aloy-Prósper, Amparo; Camacho-Alonso, Fabio

    2015-01-01

    Purpose: To report the closure of oroantral communications with the pedicled buccal fat pad in a series of patients, and to determine the level of patient satisfaction after the surgery. Study Design: A prospective study of patients diagnosed of unilateral or bilateral oroantral communication (OAC) closed using the buccal fat pad between May 2012 and January 2013 was performed. Data analysis extended to: age, sex, and cause, location and size of oroantral communication. Complications and success related to buccal fat pad surgery were evaluated. Also, patient satisfaction was assessed after six months of surgery. Results: Nine patients (3 men and 6 women) with a mean age of 50.5 years and 11 OAC treated with buccal fat pads were included. The most common cause of oroantral communication was the extraction of molars. The average widest diameter of the oroantral communication was 7.1 mm. One week after the surgeries no complications were found. One month after surgery, one patient presented persistence of the oroantral communication; in this patient, the buccal fat pad technique was considered a failure, and a second intervention was performed using a buccal mucoperiosteal flap to achieve primary closure of soft tissues. After six months, patient showed closure of the communication and complete healing. All the other communications had been solved with Bichat´s ball technique, yielding a success rate of 90.9%. Mean patient overall satisfaction was 9.1 out of 10; patients were satisfied with phonetics (9.4), aesthetics (9) and chewing (9). Conclusions: The buccal fat pad technique was successful in closing 10 out of 11 oroantral communications and few complications were found. Patients were highly satisfied in overall with the treatment and with phonetics, aesthetics and chewing. Key words:Bichat’s fat pad, buccal fat pad, oroantral communication. PMID:25810838

  12. Octopus-Inspired Smart Adhesive Pads for Transfer Printing of Semiconducting Nanomembranes.

    PubMed

    Lee, Hochan; Um, Doo-Seung; Lee, Youngsu; Lim, Seongdong; Kim, Hyung-Jun; Ko, Hyunhyub

    2016-09-01

    By mimicking muscle actuation to control cavity-pressure-induced adhesion of octopus suckers, smart adhesive pads are developed in which the thermoresponsive actuation of a hydrogel layer on elastomeric microcavity pads enables excellent switchable adhesion in response to a thermal stimulus (maximum adhesive strength: 94 kPa, adhesion switching ratio: ≈293 for temperature change between 22 and 61 °C). PMID:27322886

  13. STS-52 Columbia, OV-102, rises above KSC LC Pad 39B after liftoff

    NASA Technical Reports Server (NTRS)

    1992-01-01

    STS-52 Columbia, Orbiter Vehicle (OV) 102, leaves Kennedy Space Center (KSC) Launch Complex (LC) Pad 39B on its way toward a ten-day Earth-orbital mission. OV-102 is barely visible at the top of the exhaust cloud which covers the launch pad. The Atlantic Ocean creates the background. The photograph was taken from the Shuttle Training Aircraft (STA) piloted by astronaut Steven R. Nagel. Liftoff occurred at 1:09:39 pm (Eastern Daylight Time (EDT)).

  14. Inflammatory and Metabolic Alterations of Kager's Fat Pad in Chronic Achilles Tendinopathy

    PubMed Central

    Fredberg, Ulrich; Kjær, Søren G.; Quistorff, Bjørn; Langberg, Henning; Hansen, Jacob B.

    2015-01-01

    Background Achilles tendinopathy is a painful inflammatory condition characterized by swelling, stiffness and reduced function of the Achilles tendon. Kager’s fat pad is an adipose tissue located in the area anterior to the Achilles tendon. Observations reveal a close physical interplay between Kager’s fat pad and its surrounding structures during movement of the ankle, suggesting that Kager’s fat pad may stabilize and protect the mechanical function of the ankle joint. Aim The aim of this study was to characterize whether Achilles tendinopathy was accompanied by changes in expression of inflammatory markers and metabolic enzymes in Kager’s fat pad. Methods A biopsy was taken from Kager’s fat pad from 31 patients with chronic Achilles tendinopathy and from 13 healthy individuals. Gene expression was measured by reverse transcription-quantitative PCR. Focus was on genes related to inflammation and lipid metabolism. Results Expression of the majority of analyzed inflammatory marker genes was increased in patients with Achilles tendinopathy compared to that in healthy controls. Expression patterns of the patient group were consistent with reduced lipolysis and increased fatty acid β-oxidation. In the fat pad, the pain-signaling neuropeptide substance P was found to be present in one third of the subjects in the Achilles tendinopathy group but in none of the healthy controls. Conclusion Gene expression changes in Achilles tendinopathy patient samples were consistent with Kager’s fat pad being more inflamed than in the healthy control group. Additionally, the results indicate an altered lipid metabolism in Kager’s fat pad of Achilles tendinopathy patients. PMID:25996876

  15. Implementing a One-to-One iPad Program in a Secondary School

    ERIC Educational Resources Information Center

    Johnson, Donald P.

    2013-01-01

    The purpose of this study was to identify and analyze the necessary data and use it to determine the degree of success of the implementation process used to initiate a 1:1 iPad program in a senior high school. Use of this data enabled the district to more effectively infuse the use of the iPad into the delivery of instruction designed to improve…

  16. Assessment and Evaluation of Anatomic Variations of Retromolar Pad: A Cross Sectional Study

    PubMed Central

    Deep, Anchal; Siwach, Amit; Singh, Manas; Bhargava, Akshay; Siwach, Reenu

    2016-01-01

    Introduction The retromolar pad also called piriformis papilla is a mucosal elevation located in the retromolar area covering the retromolar triangle. After molar loss, the bony alveolar process and surrounding soft periodontal tissue remodel, mainly resorb and blend with retromolar pad. It is a key intraoral landmark in prosthodontics. Aim The aim of this in-vitro study was to analyze the various anatomical shapes and sizes of retromolar pad in 150 completely edentulous patients between 55 to 70 years of age group. Materials and Methods The study was conducted on 150 completely edentulous patients. The shapes of retromolar pad on the left and right side were seen and divided into pear, triangular and round shape. The comparison of the mean longitudinal diameter and transverse diameter on the right and left sides was done. The data was evaluated statistically. The chi-square test was used for the comparison between the proportions with the help of standard deviation, t-test was used for comparison between the left and the right side and ANOVA test was used for comparison between the various shapes of the retromolar pads. Results The result showed that there was statistically significant difference among different shapes of retromolar pad and there was significant difference in mean transverse and longitudinal diameter on right and left side, the mean value of the longitudinal diameter on left and right side was 8.81 and 8.69 whereas the mean value of the transverse diameter on left and right side was 6.79 and 6.82 respectively and p-value obtained for both was 0.550 and 0.814 respectively. Conclusion The study conclude that there are three different shapes of retromolar pad among which pear and triangular shaped retomolar pad provides more stability in lower denture because of increase surface area. PMID:27437350

  17. STS-27 Atlantis, Orbiter Vehicle (OV) 104, at KSC Launch Complex (LC) pad 39B

    NASA Technical Reports Server (NTRS)

    1988-01-01

    STS-27 Atlantis, Orbiter Vehicle (OV) 104, sits atop the mobile launcher platform at Kennedy Space Center (KSC) Launch Complex (LC) pad 39B. Profile of OV-104 mounted on external tank and flanked by solid rocket boosters (SRBs) is obscured by a flock of seagulls in the foreground. The fixed service structure (FSS) with rotating service structure (RSS) retracted appears in the background. Water resevoir is visible at the base of the launch pad concrete structure.

  18. Design charts for arbitrarily pivoted, liquid-lubricated flat-sector-pad thrust bearing

    NASA Technical Reports Server (NTRS)

    Etsion, I.

    1977-01-01

    A flat, sector-shaped geometry for a liquid-lubricated thrust bearing is analyzed considering both the pitch and roll of the pad. Results are presented in design charts that enable a direct approach to the design of point- and line-pivoted, tilting pad bearings. A comparison is made with the Mitchell bearing approximation and it is found that this approximation always overestimates load capacity.

  19. Digital representation of oil and natural gas well pad scars in southwest Wyoming

    USGS Publications Warehouse

    Garman, Steven L.; McBeth, Jamie L.

    2014-01-01

    The recent proliferation of oil and natural gas energy development in southwest Wyoming has stimulated the need to understand wildlife responses to this development. Central to many wildlife assessments is the use of geospatial methods that rely on digital representation of energy infrastructure. Surface disturbance of the well pad scars associated with oil and natural gas extraction has been an important but unavailable infrastructure layer. To provide a digital baseline of this surface disturbance, we extracted visible oil and gas well pad scars from 1-meter National Agriculture Imagery Program imagery (NAIP) acquired in 2009 for a 7.7 million-hectare region of southwest Wyoming. Scars include the pad area where wellheads, pumps, and storage facilities reside, and the surrounding area that was scraped and denuded of vegetation during the establishment of the pad. Scars containing tanks, compressors, and the storage of oil and gas related equipment, and produced-water ponds were also collected on occasion. Our extraction method was a two-step process starting with automated extraction followed by manual inspection and clean up. We used available well-point information to guide manual clean up and to derive estimates of year of origin and duration of activity on a pad scar. We also derived estimates of the proportion of non-vegetated area on a scar using a Normalized Difference Vegetation Index derived using 1-meter NAIP imagery. We extracted 16,973 pad scars of which 15,318 were oil and gas well pads. Digital representation of pad scars along with time-stamps of activity and estimates of non-vegetated area provides important baseline (circa 2009) data for assessments of wildlife responses, land-use trends, and disturbance-mediated pattern assessments.

  20. Using an eTextbook and iPad: Results of a Pilot Program

    ERIC Educational Resources Information Center

    Sloan, Roberta H.

    2013-01-01

    An eTextbook and iPad were used in a pilot program, and the impact on the course was assessed to guide the development of a college policy. Students in the course completed three questionnaires to provide feedback about their perceptions of the eTextbook and iPad. During the pilot program, students' perceptions of the usefulness, ease of use, and…

  1. New Directions for Early Literacy in a Digital Age: The iPad

    ERIC Educational Resources Information Center

    Flewitt, Rosie; Messer, David; Kucirkova, Natalia

    2015-01-01

    In this paper, we discuss how iPads offer innovative opportunities for early literacy learning but also present challenges for teachers and children. We lent iPads to a Children's Centre nursery (3- to 4-year-olds), a primary school reception class (4- to 5-year-olds) and a Special School (7- to 13-year-olds), discussed their potential uses with…

  2. Effect of Cu pad morphology on direct-Cu pillar formation in CMOS image sensors

    NASA Astrophysics Data System (ADS)

    Choi, Eunmi; Kim, Areum; Cui, Eunwha; Lee, Ukjae; Son, Hyung Bin; Hahn, Sang June; Pyo, Sung Gyu

    2014-09-01

    We report the feasibility of forming Ni bumps directly on Cu pads in CMOS image sensor (CIS) logic elements formed by Cu wires with diameters of less than 65 nm. The direct Ni bump process proposed in this study simplifies the fabrication process and reduces costs by eliminating the need for Al pad process. In addition, this process can secure the margin of the final layer, enabling the realization of thin camera modules. In this study, we evaluated the effect of pad annealing on the direct formation of Ni bumps over Cu pads. The results suggest that the morphology of the Cu pad varies depending on the annealing sequence, and post-passivation annealing resulted in fewer defects than pad etch annealing. The shear stress of the Ni bumps was 57.77 mgf/m2, which is six times greater than the corresponding reference value. Furthermore, we evaluated the reliability of a chip with an anisotropic conductive film (ACF) and a non-conducting paste (NCP) by using high-temperature storage (HTS), thermal cycling (TC), and wet high-temperature storage (WHTS) reliability tests. The evaluation results suggest the absence of abnormalities in all samples. [Figure not available: see fulltext.

  3. Next Generation Non-particulate Dry Nonwoven Pad for Chemical Warfare Agent Decontamination

    SciTech Connect

    Ramkumar, S S; Love, A; Sata, U R; Koester, C J; Smith, W J; Keating, G A; Hobbs, L; Cox, S B; Lagna, W M; Kendall, R J

    2008-05-01

    New, non-particulate decontamination materials promise to reduce both military and civilian casualties by enabling individuals to decontaminate themselves and their equipment within minutes of exposure to chemical warfare agents or other toxic materials. One of the most promising new materials has been developed using a needlepunching nonwoven process to construct a novel and non-particulate composite fabric of multiple layers, including an inner layer of activated carbon fabric, which is well-suited for the decontamination of both personnel and equipment. This paper describes the development of a composite nonwoven pad and compares efficacy test results for this pad with results from testing other decontamination systems. The efficacy of the dry nonwoven fabric pad was demonstrated specifically for decontamination of the chemical warfare blister agent bis(2-chloroethyl)sulfide (H or sulfur mustard). GC/MS results indicate that the composite fabric was capable of significantly reducing the vapor hazard from mustard liquid absorbed into the nonwoven dry fabric pad. The mustard adsorption efficiency of the nonwoven pad was significantly higher than particulate activated carbon (p=0.041) and was similar to the currently fielded US military M291 kit (p=0.952). The nonwoven pad has several advantages over other materials, especially its non-particulate, yet flexible, construction. This composite fabric was also shown to be chemically compatible with potential toxic and hazardous liquids, which span a range of hydrophilic and hydrophobic chemicals, including a concentrated acid, an organic solvent and a mild oxidant, bleach.

  4. A microcasted PDMS vacuum pad and its application for stacking thin ceramic layers

    NASA Astrophysics Data System (ADS)

    Hwang, Sung Jin; Lee, Sang Min; Jung, Im Deok; Jung, Phill Gu; Go, Jeung Sang; Ko, Jong Soo

    2009-08-01

    A PDMS vacuum pad for stacking very thin green sheets with a 3 µm thick dielectric layer is introduced and fabricated. Its applicability for producing multi-layer ceramic capacitors (MLCCs) is evaluated. Five micro-holes with a diameter and depth of 70 µm are formed on a single vacuum-line unit that is of 120 µm width, 100 µm depth and 2 mm length. Each vacuum-line unit with five micro-holes is deployed at 6 mm intervals on a PDMS vacuum pad of size 166 mm × 166 mm. To fabricate the PDMS vacuum pads, a mold with an obverse structure to that of the PDMS vacuum pad is needed. The metal mold has a two-stage nickel microstructure, the first stage for forming the vacuum lines and the second stage for forming the micro-holes. To fabricate the mold, micromachining processes, including photolithography, nickel/copper electroforming and chemical mechanical polishing, were conducted twice on a precision-machined SUS substrate with a size of 210 mm × 210 mm. The PDMS vacuum pads were fabricated through a microcasting process. Using the PDMS vacuum pad, 320 layers of green sheets, upon which nickel electrodes were patterned on 3 µm thick dielectric layers, were consecutively stacked. It has been observed that the stacked green sheets were very flat and uniform without any distortion or wrinkles. It is believed that the uniform stacking will greatly help to improve the production yield as well as enhance the reliability of MLCCs.

  5. Small Buccal Fat Pad Cells Have High Osteogenic Differentiation Potential.

    PubMed

    Tsurumachi, Niina; Akita, Daisuke; Kano, Koichiro; Matsumoto, Taro; Toriumi, Taku; Kazama, Tomohiko; Oki, Yoshinao; Tamura, Yoko; Tonogi, Morio; Isokawa, Keitaro; Shimizu, Noriyoshi; Honda, Masaki

    2016-03-01

    Dedifferentiated fat (DFAT) cells derived from mature adipocytes have mesenchymal stem cells' (MSCs) characteristics. Generally, mature adipocytes are 60-110 μm in diameter; however, association between adipocyte size and dedifferentiation efficiency is still unknown. This study, therefore, investigated the dedifferentiation efficiency of adipocytes based on cell diameter. Buccal fat pad was harvested from five human donors and dissociated by collagenase digestion. After exclusion of unwanted stromal cells by centrifugation, floating adipocytes were collected and their size distribution was analyzed. The floating adipocytes were then separated into two groups depending on cell size using 40- and 100-μm nylon mesh filters: cell diameters less than 40 μm (small adipocytes: S-adipocytes) and cell diameters of 40-100 μm (large adipocytes: L-adipocytes). Finally, we evaluated the efficiency of adipocyte dedifferentiation and then characterized the resultant DFAT cells. The S-adipocytes showed a higher capacity to dedifferentiate into DFAT cells (S-DFAT cells) compared to the L-adipocytes (L-DFAT cells). The S-DFAT cells also showed a relatively higher proportion of CD146-positive cells than L-DFAT cells, and exhibited more osteogenic differentiation ability based on the alkaline phosphatase activity and amount of calcium deposition. These results suggested that the S- and L-DFAT cells had distinct characteristics, and that the higher dedifferentiation potential of S-adipocytes compared to L-adipocytes gives the former group an advantage in yielding DFAT cells. PMID:26651216

  6. Sequential Activation of a Segmented Ground Pad Reduces Skin Heating During Radiofrequency Tumor Ablation: Optimization via Computational Models

    PubMed Central

    Schutt, David J.; Haemmerich, Dieter

    2009-01-01

    Radiofrequency (RF) ablation has become an accepted treatment modality for unresectable tumors. The need for larger ablation zones has resulted in increased RF generator power. Skin burns due to ground pad heating are increasingly limiting further increases in generator power, and thus, ablation zone size. We investigated a method for reducing ground pad heating in which a commercial ground pad is segmented into multiple ground electrodes, with sequential activation of ground electrode subsets. We created finite-element method computer models of a commercial ground pad (14 × 23 cm) and compared normal operation of a standard pad to sequential activation of a segmented pad (two to five separate ground electrode segments). A constant current of 1 A was applied for 12 min in all simulations. Time periods during sequential activation simulations were adjusted to keep the leading edge temperatures at each ground electrode equal. The maximum temperature using standard activation of the commercial pad was 41.7 °C. For sequential activation of a segmented pad, the maximum temperature ranged from 39.3 °C (five segments) to 40.9 °C (two segments). Sequential activation of a segmented ground pad resulted in lower tissue temperatures. This method may reduce the incidence of ground pad burns and enable the use of higher power generators during RF tumor ablation. PMID:18595807

  7. Effect of Metal Bond-Pad Configurations on the Solder Microstructure Development of Flip-Chip Solder Joints

    NASA Astrophysics Data System (ADS)

    Hu, Y. J.; Hsu, Y. C.; Huang, T. S.; Lu, C. T.; Wu, Albert T.; Liu, C. Y.

    2014-01-01

    Various microstructural zones were observed in the solidified solder of flip-chip solder joints with three metal bond-pad configurations (Cu/Sn/Cu, Ni/Sn/Cu, and Cu/Sn/Ni). The developed microstructures of the solidified flip-chip solder joints were strongly related to the associated metal bond pad. A hypoeutectic microstructure always developed near the Ni bond pad, and a eutectic or hypereutectic microstructure formed near the Cu pad. The effect of the metal bond pads on the solder microstructure alters the Cu solubility in the molten solder. The Cu content (solubility) in the molten Sn(Cu) solder eventually leads to the development of particular microstructures. In addition to the effect of the associated metal bond pads, the developed microstructure of the flip-chip solder joint depends on the configuration of the metal bond pads. A hypereutectic microstructure formed near the bottom Cu pad, and a eutectic microstructure formed near the top Cu pad. Directional cooling in the flip-chip solder joint during the solidification process causes the effects of the metal bond-pad configuration. Directional cooling causes the Cu content to vary in the liquid Sn(Cu) phase, resulting in the formation of distinct microstructural zones in the developed microstructure of the flip-chip solder joint.

  8. ImagePAD, a novel counting application for the Apple iPad, used to quantify axons in the mouse optic nerve.

    PubMed

    Templeton, Justin P; Struebing, Felix L; Lemmon, Andrew; Geisert, Eldon E

    2014-11-01

    The present article introduces a new and easy to use counting application for the Apple iPad. The application "ImagePAD" takes advantage of the advanced user interface features offered by the Apple iOS platform, simplifying the rather tedious task of quantifying features in anatomical studies. For example, the image under analysis can be easily panned and zoomed using iOS-supported multi-touch gestures without losing the spatial context of the counting task, which is extremely important for ensuring count accuracy. This application allows one to quantify up to 5 different types of objects in a single field and output the data in a tab-delimited format for subsequent analysis. We describe two examples of the use of the application: quantifying axons in the optic nerve of the C57BL/6J mouse and determining the percentage of cells labeled with NeuN or ChAT in the retinal ganglion cell layer. For the optic nerve, contiguous images at 60× magnification were taken and transferred onto an Apple iPad. Axons were counted by tapping on the touch-sensitive screen using ImagePAD. Nine optic nerves were sampled and the number of axons in the nerves ranged from 38,872 axons to 50,196 axons with an average of 44,846 axons per nerve (SD = 3980 axons). PMID:25281829

  9. Nanoabrasives retention and removal mechanisms in polyurethane pads for copper CMP

    NASA Astrophysics Data System (ADS)

    Ul-Hasan, Iftikhar

    The continued reduction in integrated circuit (IC) feature size requires similar reductions in surface defectivity. A key source of surface defects in IC fabrication processes stems from nanoabrasives used in chemical-mechanical planarization (CMP) processing. During CMP processing, polished surfaces are more vulnerable to defects including scratching, nanoabrasive particle adhesion and nanoabrasive agglomerate adhesion. The removal of these nano-sized particles is a priority for the IC fabrication industry and is reflected in the 2008 ITRS defect budget. However, there is insufficient technical understanding regarding the retention of residual nanoabrasives on the surfaces of the CMP pad following a CMP process and how they can be removed. Particularly, there are no systematic quantitative studies regarding nanoabrasive transport - specifically, nanoabrasive retention, agglomeration and removal mechanisms at pad surfaces (including micro-pores and asperities) that have been exposed (or not exposed) to polishing. In this dissertation research regarding the residual nanoabrasive transport in IC1000/SubaIV polyurethane pads following a Cu CMP process is presented. Removal mechanisms of residual nanoabrasive resident at CMP pad pores and asperities via a diamond pad conditioning disk is investigated for a range of conditioning parameters, nanoabrasive particles, and slurry formulations. Qualitative and quantitative analysis of nanoabrasive retention was carried out via conventional and environmental scanning electron microscopy (SEM and ESEM), x-ray photoelectron spectroscopy (XPS) and SEM-based energy dispersion spectroscopy (SEM-EDS). To quantitatively describe the spectroscopic nanoabrasive retention data a semi-empirical model was developed. Quantitative spectroscopic and microscopic analyses on IC1000 CMP pads revealed considerable CMP slurry nanoabrasive retention at pad asperities and open pores that contacted the wafer during Cu CMP. Some of this residual

  10. Analysis of the March 30, 2011 Hail Event at Shuttle Launch Pad 39A

    NASA Technical Reports Server (NTRS)

    Lane, John E.; Doesken, Nolan J.; Kasparis, Takis C.; Sharp, David W.

    2012-01-01

    The Kennedy Space Center (KSC) Hail Monitor System, a joint effort of the NASA KSC Physics Lab and the KSC Engineering Services Contract (ESC) Applied Technology Lab, was first deployed for operational testing in the fall of 2006. Volunteers from the Community Collaborative Rain, Hail, and Snow Network (CoCoRaHS) in conjunction with Colorado State University have been instrumental in validation testing using duplicate hail monitor systems at sites in the hail prone high plains of Colorado. The KSC Hail Monitor System (HMS), consisting of three stations positioned approximately 500 ft from the launch pad and forming an approximate equilateral triangle, as shown in Figure 1, was first deployed to Pad 39B for support of STS-115. Two months later, the HMS was deployed to Pad 39A for support of STS-116. During support of STS-117 in late February 2007, an unusually intense (for Florida standards) hail event occurred in the immediate vicinity of the exposed space shuttle and launch pad. Hail data of this event was collected by the HMS and analyzed. Support of STS-118 revealed another important application of the hail monitor system. Ground Instrumentation personnel check the hail monitors daily when a vehicle is on the launch pad, with special attention after any storm suspected of containing hail. If no hail is recorded by the HMS, the vehicle and pad inspection team has no need to conduct a thorough inspection of the vehicle immediately following a storm. On the afternoon of July 13, 2007, hail on the ground was reported by observers at the Vertical Assembly Building (VAB) and Launch Control Center (LCC), about three miles west of Pad 39A, as well as at several other locations at KSC. The HMS showed no impact detections, indicating that the shuttle had not been damaged by any of the numerous hail events which occurred on that day.

  11. The Effect of Rotor Disc Material on Tribo Behavior of Automotive Brake Pad Materials

    NASA Astrophysics Data System (ADS)

    Liew, K. W.; El-Tayeb, N. S. M.

    This work aims to investigate the effect of two different counterdisc materials, i.e. gray cast iron (GCI) and ductile gray cast iron (DGCI) on tribo behavior of non-commercial frictional materials (NF1, NF2, NF4, and NF5) and two other chosen commercial brake pads (CMA and CMB) under dry sliding contact conditions. The four non-commercial frictional materials were fabricated with various percentages of phenolic binder resin (15 and 20 vol.%) and reinforced with steel fibers (15 and 20 vol.%) using hot press molding methods. Tribo tests were carried out using a small-scale tribo-tester of pad-on-disc type. Friction coefficient and wear of non-commercial and commercial brake pads were measured against each counterdisc (GCI and DGCI) and compared. Then, the friction and wear characteristic are discussed by comparing the experimental results obtained for each kind of cast iron. The results showed that maximum friction coefficient (0.4-0.5) of brake pad was attained at 2.22 MPa applied pressure and 2.1 m/s sliding speed when the frictional brake pad materials were tested against DGCI disc rotor. Meanwhile, similar wear rates for all frictional brake pad materials were sustained at higher applied pressure and sliding speed when tested against either type of rotor discs (GCI and DGCI). The results on the other hand, indicated that non-commercial materials NF1 and NF4, gave better wear resistance compared to other frictional pad materials. NF2 exhibited the lowest wear resistance when tested against GCI and DGCI rotor disc at all applied pressure and sliding speeds. The latter result is referred to the low percentage binder resin in the friction material NF2.

  12. A pilot study investigating the utilization of crest pads for treatment of toe callus and ulceration.

    PubMed

    Melo, Monica; Bernecker, Tricia; McCullough, James; Hong, John; Trumbauer, Jane Scott; Miller, Mary Ellen

    2015-12-01

    Patients with lesser-toe deformities are at increased risk of developing calluses and ulcers on the distal ends of the affected digits because of the increased pressures applied to these areas. The number of diabetic patients in the United States continues to increase, along with associated comorbidities such as peripheral vascular disease and peripheral neuropathy. These conditions predispose patients to developing foot ulcerations, especially if foot deformities are present. Crest pads are a simple-to-make, inexpensive option to treat calluses and ulcerations on the distal ends of digits; however, there is no research available that support their use. Crest pads consist of rolled gauze covered in moleskin, with a large opening that fits over several toes and lies on the dorsal aspect of the foot, with the padded portion resting under the toes. Over several days of use, the pad molds to the plantar aspect of the toes, offloading pressure from the distal end of the affected digit(s). The sample was obtained through a retrospective chart review of patients identified as having had at least one nail care visit and at least one follow-up visit at a vascular surgery practice between August 2011 and December 2014. Potential subjects with toe deformities who presented with callus or ulcer on the distal end of a digit were considered for inclusion, if they received a crest pad as part of their treatment plan. The scholarly project was a preintervention or postintervention design with subjects acting as their own controls. McNemar's test was used to analyze the results which were statistically significant (P < .0001 at first callus follow-up and P = .0002 at second callus follow-up) for callus, hemorrhagic callus, and/or ulcer improvement following the crest pad intervention. The results of this scholarly project support the use of crest pads in patients with lesser-toe deformities to treat distal toe calluses and/or ulcerations. PMID:26567055

  13. NASA's Space Launch System: Moving Toward the Launch Pad

    NASA Technical Reports Server (NTRS)

    Creech, Stephen D.; May, Todd A.

    2013-01-01

    The National Aeronautics and Space Administration's (NASA's) Space Launch System (SLS) Program, managed at the Marshall Space Flight Center (MSFC), is making progress toward delivering a new capability for human space flight and scientific missions beyond Earth orbit. Designed with the goals of safety, affordability, and sustainability in mind, the SLS rocket will launch the Orion Multi-Purpose Crew Vehicle (MPCV), equipment, supplies, and major science missions for exploration and discovery. Supporting Orion's first autonomous flight to lunar orbit and back in 2017 and its first crewed flight in 2021, the SLS will evolve into the most powerful launch vehicle ever flown via an upgrade approach that will provide building blocks for future space exploration. NASA is working to deliver this new capability in an austere economic climate, a fact that has inspired the SLS team to find innovative solutions to the challenges of designing, developing, fielding, and operating the largest rocket in history. This paper will summarize the planned capabilities of the vehicle, the progress the SLS Program has made in the 2 years since the Agency formally announced its architecture in September 2011, the path it is following to reach the launch pad in 2017 and then to evolve the 70 metric ton (t) initial lift capability to 130-t lift capability after 2021. The paper will explain how, to meet the challenge of a flat funding curve, an architecture was chosen that combines the use and enhancement of legacy systems and technology with strategic new developments that will evolve the launch vehicle's capabilities. This approach reduces the time and cost of delivering the initial 70 t Block 1 vehicle, and reduces the number of parallel development investments required to deliver the evolved 130 t Block 2 vehicle. The paper will outline the milestones the program has already reached, from developmental milestones such as the manufacture of the first flight hardware, to life

  14. NASA's Space Launch System: Moving Toward the Launch Pad

    NASA Technical Reports Server (NTRS)

    Creech, Stephen D.; May, Todd

    2013-01-01

    The National Aeronautics and Space Administration's (NASA's) Space Launch System (SLS) Program, managed at the Marshall Space Flight Center, is making progress toward delivering a new capability for human space flight and scientific missions beyond Earth orbit. Developed with the goals of safety, affordability, and sustainability in mind, the SLS rocket will launch the Orion Multi-Purpose Crew Vehicle (MPCV), equipment, supplies, and major science missions for exploration and discovery. Supporting Orion's first autonomous flight to lunar orbit and back in 2017 and its first crewed flight in 2021, the SLS will evolve into the most powerful launch vehicle ever flown, via an upgrade approach that will provide building blocks for future space exploration and development. NASA is working to develop this new capability in an austere economic climate, a fact which has inspired the SLS team to find innovative solutions to the challenges of designing, developing, fielding, and operating the largest rocket in history. This paper will summarize the planned capabilities of the vehicle, the progress the SLS program has made in the 2 years since the Agency formally announced its architecture in September 2011, and the path the program is following to reach the launch pad in 2017 and then to evolve the 70 metric ton (t) initial lift capability to 130-t lift capability. The paper will explain how, to meet the challenge of a flat funding curve, an architecture was chosen which combines the use and enhancement of legacy systems and technology with strategic new development projects that will evolve the capabilities of the launch vehicle. This approach reduces the time and cost of delivering the initial 70 t Block 1 vehicle, and reduces the number of parallel development investments required to deliver the evolved version of the vehicle. The paper will outline the milestones the program has already reached, from developmental milestones such as the manufacture of the first flight

  15. iPads at Field Camp: A First Test of the Challenges and Opportunities

    NASA Astrophysics Data System (ADS)

    Hurst, S. D.; Stewart, M. A.

    2011-12-01

    An iPad 2 was given to approximately half of the University of Illinois students attending the Wasatch-Uinta Field Camp (WUFC) in summer 2011. The iPads were provisioned with orientation measuring, mapping and location software. The software would automatically transfer an orientation measurement to the current location on the Google Maps application, and was able to output a full list of orientation data. Students also had normal access to more traditional mapping tools such as Brunton compasses and GPS units and were required to map with these tools along with other students of WUFC not provided iPads. Compared to traditional tools, iPads have drawbacks such as increased weight, break-ability, need for power source and wireless connectivity; in sum, they need a substantial infrastructure that reduces range, availability, and probably most importantly, convenience. Some of these drawbacks inhibited adoption by our students, the primary reasons being the added weight and the inability to map directly to a GIS application with detailed topographic maps equivalent to the physical topographic map sheets used at WUFC. In their favor, the iPads combine a host of tools into one, including software that can measure orientation in a fashion more intuitively than a Brunton. They also allow storage, editing and analysis of data, notes (spoken and/or written) and potentially unlimited access to a variety of maps. Via a post-field camp survey of the University of Illinois students at WUFC, we have identified some of the important issues that need to be addressed before portable tablets like the iPad become the tool of choice for general field work. Some problems are intrinsic to almost any advanced technology, some are artifacts of the current generations of hardware and software available for these devices. Technical drawbacks aside, the adoption of iPads was further inhibited primarily by inexperience with their use as a mapping tool and secondarily by their redundancy with

  16. A quantitative study of aromatic amine permeation through protective gloves using amine adsorptive pads.

    PubMed

    Vo, E; Berardinelli, S P; Hall, R C; El Ayouby, N

    2000-01-01

    A quantitative study of aromatic amine permeation through a glove material using Permea-Tec aromatic amine pads, used for the detection of chemical breakthrough of protective clothing, was performed for aniline following the microwave extraction process and gas chromatographic analysis. Aniline exhibited >99% adsorption on the pads at a spiking level of 1.94 mg (1.9 microL). Aniline showed recoveries from 65 to 89% (RSD < or =5.6%) over the range 1.1-1.9 microL (1.12-1.94 mg) of aniline applied to pads. The modified ASTM F739 and direct permeability testing procedures were used to determine breakthrough times for five protective glove materials using aniline as a challenge chemical. Breakthrough times for six protective gloves were determined, ranging from 182 sec to 82 min. The quantitative concentration of aniline on the pads following permeation through the gloves also was determined, ranging from 0.53 to 0.55 mg/cm2 (1.79-1.88 mg/pad). PMID:11192217

  17. A mathematical method for quantifying in vivo mechanical behaviour of heel pad under dynamic load.

    PubMed

    Naemi, Roozbeh; Chatzistergos, Panagiotis E; Chockalingam, Nachiappan

    2016-03-01

    Mechanical behaviour of the heel pad, as a shock attenuating interface during a foot strike, determines the loading on the musculoskeletal system during walking. The mathematical models that describe the force deformation relationship of the heel pad structure can determine the mechanical behaviour of heel pad under load. Hence, the purpose of this study was to propose a method of quantifying the heel pad stress-strain relationship using force-deformation data from an indentation test. The energy input and energy returned densities were calculated by numerically integrating the area below the stress-strain curve during loading and unloading, respectively. Elastic energy and energy absorbed densities were calculated as the sum of and the difference between energy input and energy returned densities, respectively. By fitting the energy function, derived from a nonlinear viscoelastic model, to the energy density-strain data, the elastic and viscous model parameters were quantified. The viscous and elastic exponent model parameters were significantly correlated with maximum strain, indicating the need to perform indentation tests at realistic maximum strains relevant to walking. The proposed method showed to be able to differentiate between the elastic and viscous components of the heel pad response to loading and to allow quantifying the corresponding stress-strain model parameters. PMID:26044551

  18. Relaxation nuclear magnetic resonance imaging (R-NMRI) of desiccation in M9787 silicone pads.

    SciTech Connect

    Alam, Todd M; Cherry, Brian Ray; Alam, Mary Kathleen

    2004-06-01

    The production and aging of silicone materials remains an important issue in the weapons stockpile due to their utilization in a wide variety of components and systems within the stockpile. Changes in the physical characteristics of silicone materials due to long term desiccation has been identified as one of the major aging effects observed in silicone pad components. Here we report relaxation nuclear magnetic resonance imaging (R-NMRI) spectroscopy characterization of the silica-filled and unfilled polydimethylsiloxane (PDMS) and polydiphenylsiloxane (PDPS) copolymer (M9787) silicone pads within desiccating environments. These studies were directed at providing additional details about the heterogeneity of the desiccation process. Uniform NMR spin-spin relaxation time (T2) images were observed across the pad thickness indicating that the drying process is approximately uniform, and that the desiccation of the M9787 silicone pad is not a H2O diffusion limited process. In a P2O5 desiccation environment, significant reduction of T2 was observed for the silica-filled and unfilled M9787 silicone pad for desiccation up to 225 days. A very small reduction in T2 was observed for the unfilled copolymer between 225 and 487 days. The increase in relative stiffness with desiccation was found to be higher for the unfilled copolymer. These R-NMRI results are correlated to local changes in the modulus of the material

  19. STS-96 Space Shuttle Discovery rolls back to Launch Pad 39B

    NASA Technical Reports Server (NTRS)

    1999-01-01

    Both Space Shuttle Discovery (left) and Launch Pad 39B (right) are reflected in nearby water as the Shuttle makes its slow crawl to the pad aboard a crawler transporter. Earlier in the week, the Shuttle was rolled back from the pad to the Vehicle Assembly Building to repair hail damage on the the external tank's foam insulation. The 4.2-mile trek takes about five hours at the 1-mph speed of the crawler. Mission STS-96, the 94th launch in the Space Shuttle Program, is scheduled for liftoff May 27 at 6:48 a.m. EDT. STS-96 is a logistics and resupply mission for the International Space Station, carrying such payloads as a Russian crane, the Strela; a U.S.-built crane; the Spacehab Oceaneering Space System Box (SHOSS), a logistics items carrier; and STARSHINE, a student-shared experiment.

  20. On the accuracy of the Padé-resummed master equation approach to dissipative quantum dynamics

    NASA Astrophysics Data System (ADS)

    Chen, Hsing-Ta; Berkelbach, Timothy C.; Reichman, David R.

    2016-04-01

    Well-defined criteria are proposed for assessing the accuracy of quantum master equations whose memory functions are approximated by Padé resummation of the first two moments in the electronic coupling. These criteria partition the parameter space into distinct levels of expected accuracy, ranging from quantitatively accurate regimes to regions of parameter space where the approach is not expected to be applicable. Extensive comparison of Padé-resummed master equations with numerically exact results in the context of the spin-boson model demonstrates that the proposed criteria correctly demarcate the regions of parameter space where the Padé approximation is reliable. The applicability analysis we present is not confined to the specifics of the Hamiltonian under consideration and should provide guidelines for other classes of resummation techniques.

  1. Structural design of concrete storage pads for spent-fuel casks

    SciTech Connect

    Rashid, Y.R.; Nickell, R.E.; James, R.J. )

    1993-04-01

    The loading experienced by spent fuel dry storage casks and storage pads due to potential drop or tip-over accidents is evaluated using state-of-the-art concrete structural analysis methodology. The purpose of this analysis is to provide simple design charts and formulas so that design adequacy of storage pads and dry storage casks can be demonstrated. The analysis covers a wide range of slab-design parameters, e.g., reinforcement ratio, slab thickness, concrete compressive strength, and sub-base soil compaction, as well as variations in drop orientation and drop height. The results are presented in the form of curves, giving the force on the cask as a function of storage pad hardness for various drop heights. In addition, force-displacement curves, deformed shapes, crack patterns, stresses and strains are given for various slab-design conditions and drop events. The utility of the results in design are illustrated through examples.

  2. On the accuracy of the Padé-resummed master equation approach to dissipative quantum dynamics.

    PubMed

    Chen, Hsing-Ta; Berkelbach, Timothy C; Reichman, David R

    2016-04-21

    Well-defined criteria are proposed for assessing the accuracy of quantum master equations whose memory functions are approximated by Padé resummation of the first two moments in the electronic coupling. These criteria partition the parameter space into distinct levels of expected accuracy, ranging from quantitatively accurate regimes to regions of parameter space where the approach is not expected to be applicable. Extensive comparison of Padé-resummed master equations with numerically exact results in the context of the spin-boson model demonstrates that the proposed criteria correctly demarcate the regions of parameter space where the Padé approximation is reliable. The applicability analysis we present is not confined to the specifics of the Hamiltonian under consideration and should provide guidelines for other classes of resummation techniques. PMID:27389208

  3. A behind-the-scenes look at the safety assessment of feminine hygiene pads.

    PubMed

    Farage, Miranda A

    2006-12-01

    Forms of menstrual protection have evolved with time. Today's disposable feminine hygiene products, notably sanitary pads, include a wide range of designs and features to meet women's needs for reliable, discreet, and comfortable protection. Manufacturers support substantive research and testing programs to ensure the safety of these products. The premarket safety assessment of feminine hygiene pads is a systematic, stepwise process that includes toxicological evaluation of the raw materials, the conduct of prospective, controlled clinical trials to assess product safety-in-use, and, in some cases, independent scientific review. A broad clinical database, developed over the past 20 years, substantiates that modern, feminine hygiene pads are not associated with significant gynecological, dermatological, or microbiological effects. Postmarket surveillance provides reassurance that the products are acceptable to consumers worldwide. PMID:17308134

  4. Performance studies of a Micromegas detector with a pad readout geometry

    NASA Astrophysics Data System (ADS)

    Düdder, A.; Lin, T.-H.; Neuhaus, F.; Schott, M.; Valderanis, C.

    2016-07-01

    The results of several performance studies of two prototype Micromegas pad detectors with two different coupling implementations between the resistive and the readout layer are presented. Both prototype detectors have an active area of 10 × 10cm2 and comprise 500 pads with a size of 5 × 4mm2. The first detector has a capacitive coupling between the resistive and the readout layer, as it is well known from Micromegas detectors with a strip readout. The second detector implements a resistive coupling between each readout pad and the resistive layer on top of it with a resistivity of 5 MΩ. In particular, the size of reconstructed charge clusters in both detector types is discussed and compared here for different drift- and amplification voltages.

  5. Using iPads to Teach Communication Skills of Students with Autism.

    PubMed

    Xin, Joy F; Leonard, Deborah A

    2015-12-01

    The purpose of this study was to examine the effects of using an iPad to assist students with autism in learning communication skills. Three, 10 years old learners diagnosed with autism who present little or no functional speech, participated in the study. A multiple baseline design with AB phases across academic and social settings was used. During the baseline, students were given access to an iPad with the SonoFlex speech-generating device application, while no communicative attempts were observed. During the intervention, the students were taught to use the iPad to communicate with their teacher and peers for 6 weeks. With a least-to-most prompting hierarchy, all students increased initiating requests, responding to questions and making social comments in both class and recess settings. PMID:25294648

  6. A flexible nanobrush pad for the chemical mechanical planarization of Cu/ultra-low-к materials

    NASA Astrophysics Data System (ADS)

    Han, Guiquan; Liu, Yuhong; Lu, Xinchun; Luo, Jianbin

    2012-10-01

    A new idea of polishing pad called flexible nanobrush pad (FNP) has been proposed for the low down pressure chemical mechanical planarization (CMP) process of Cu/ultra-low-к materials. The FNP was designed with a surface layer of flexible brush-like nanofibers which can `actively' carry nanoscale abrasives in slurry independent of the down pressure. Better planarization performances including high material removal rate, good planarization, good polishing uniformity, and low defectivity are expected in the CMP process under the low down pressure with such kind of pad. The FNP can be made by template-assisted replication or template-based synthesis methods, which will be driven by the development of the preparation technologies for ordered nanostructure arrays. The present work would potentially provide a new solution for the Cu/ultra-low-к CMP process.

  7. Targeted Evolution of Embedded Librarian Services: Providing Mobile Reference and Instruction Services Using iPads.

    PubMed

    Stellrecht, Elizabeth; Chiarella, Deborah

    2015-01-01

    The University at Buffalo Health Sciences Library provides reference and instructional services to support research, curricular, and clinical programs of the University at Buffalo. With funding from an NN/LM MAR Technology Improvement Award, the University at Buffalo Health Sciences Library (UBHSL) purchased iPads to develop embedded reference and educational services. Usage statistics were collected over a ten-month period to measure the frequency of iPad use for mobile services. While this experiment demonstrates that the iPad can be used to meet the library user's needs outside of the physical library space, this article will also offer advice for others who are considering implementing their own program. PMID:26496394

  8. The RSS rolls back revealing STS-102 Discovery on Launch Pad 39B

    NASA Technical Reports Server (NTRS)

    2001-01-01

    KENNEDY SPACE CENTER, Fla. - Workers watch the rollback of the Rotating Service Structure (left) from around Space Shuttle Discovery on Launch Pad 39B. Poised above the orange external tank is the Gaseous Oxygen Vent Arm with the '''beanie cap,''' a vent hood. The RSS provides protected access to the orbiter for changeout and servicing of payloads. It is supported by a rotating bridge that pivots about a vertical axis on the west side of the pad'''s flame trench. Space Shuttle Discovery is scheduled to launch March 8 at 6:42 a.m. EST on the eighth construction flight to the International Space Station. It carries the Multi-Purpose Logistics Module Leonardo, the primary delivery system used to resupply and return Station cargo requiring a pressurized environment. Leonardo will deliver up to 10 tons of laboratory racks filled with equipment, experiments and supplies for outfitting the newly installed U.S. Laboratory Destiny.

  9. A flexible nanobrush pad for the chemical mechanical planarization of Cu/ultra-low-к materials

    PubMed Central

    2012-01-01

    A new idea of polishing pad called flexible nanobrush pad (FNP) has been proposed for the low down pressure chemical mechanical planarization (CMP) process of Cu/ultra-low-к materials. The FNP was designed with a surface layer of flexible brush-like nanofibers which can ‘actively’ carry nanoscale abrasives in slurry independent of the down pressure. Better planarization performances including high material removal rate, good planarization, good polishing uniformity, and low defectivity are expected in the CMP process under the low down pressure with such kind of pad. The FNP can be made by template-assisted replication or template-based synthesis methods, which will be driven by the development of the preparation technologies for ordered nanostructure arrays. The present work would potentially provide a new solution for the Cu/ultra-low-к CMP process. PMID:23110959

  10. Nesting bird deterrents for the Federal Republic of Germany glass log storage pad

    SciTech Connect

    Mitchell, R.M.

    1997-04-15

    A proposed storage pad wi11 be constructed in the 200 West Area for the storage of isotopic heat and radiation sources from the Federal Republic of Germany. The pad will be constructed in the southern portion of the Solid Waste Operations Complex near the existing Sodium Storage Pad (Figure 1). Following a biological review by Pacific Northwest National Laboratory (PNNL) personnel (Brandt 1996), it was determined that in order for construction to take place after March 15, 1997, actions would need to be taken to prevent migratory birds from nesting in the project area. Special attention was focused on preventing sage sparrows and loggerhead shrikes, both Hanford Site species of concern (DOE/RL 1996), from nesting in the area. This activity plan details the methods and procedures that will be used to implement these nesting deterrents.

  11. Gas Seal Pad With Herringbone-Grooved Rotor-Stiffness and Load Capacity

    NASA Technical Reports Server (NTRS)

    Flemming, David P.

    2006-01-01

    The principle of herringbone-grooved journal bearings has been applied to the case of a seal disc running under a finger seal pad. The inward pumping action of herringbone grooves on the disc generates load capacity and stiffness to maintain a fluid film and prevent contact of the pad and disc. This mechanism does not depend on a converging film under the pad, such as analyzed in previous works. Analysis shows that significant stiffness and load capacity can be supplied by herringbone grooves. In order for the grooves to be effective, the seal pressure drop must be taken outside of the grooved portion of the rotor, but this may be acceptable in order to gain freedom from maintaining a precise film convergence.

  12. Space Shuttle and Launch Pad Lift-Off Debris Transport Analysis: SRB Plume-Driven

    NASA Technical Reports Server (NTRS)

    West, Jeff; Strutzenberg, Louis; Dougherty, Sam; Radke, Jerry; Liever, Peter

    2007-01-01

    This paper discusses the Space Shuttle Lift-Off model developed for potential Lift-Off Debris transport. A critical Lift-Off portion of the flight is defined from approximately 1.5 sec after SRB Ignition up to 'Tower Clear', where exhaust plume interactions with the Launch Pad occur. A CFD model containing the Space Shuttle and Launch Pad geometry has been constructed and executed. The CFD model works in conjunction with a debris particle transport model and a debris particle impact damage tolerance model. These models have been used to assess the effects of the Space Shuttle plumes, the wind environment, their interactions with the Launch Pad, and their ultimate effect on potential debris during Lift-Off. Emphasis in this paper is on potential debris that might be caught by the SRB plumes.

  13. Preliminary results obtained from novel CdZnTe pad detectors

    SciTech Connect

    Tuemer, T.O.; Joyce, D.C.; Yin, S.; Willson, P.D.; Parnham, K.B.; Glick, B.

    1996-06-01

    CdZnTe pad detectors with a novel geometry and approximately 1 mm{sup 2} pad sizes are being developed. These detectors have been specially designed for high energy resolution up to 300 keV energies. The contacts are produced through a unique technique developed by eV Products to achieve high reliability low resistance coupling to the substrate. A ceramic carrier is developed for low capacitance coupling of the detectors to NOVA`s FEENA chip. The detectors have been tested using the ultra low noise single and 3-channel amplifiers developed by eV Products. The CdZnTe detectors are tested for dark current. The charge energy resolutions and collection times are also measured using natural radiation sources. The measured detector parameters and the test results are showing that linear pad arrays can have good uniformity and excellent application potential for imaging x-rays and gamma-rays.

  14. Deformation analysis of Hoffa's fat pad from CT images of knee flexion and extension

    NASA Astrophysics Data System (ADS)

    Hamarneh, Ghassan; Chu, Vincent; Bordalo-Rodrigues, Marcelo; Schweitzer, Mark

    2005-04-01

    Recent advances in medicine conjecture that certain body fat may have mechanical function in addition to its classical role of energy storage. In particular we aim to analyze if the intra-articular fat pad of Hoffa is merely a space holder or if it changes shape to provide cushioning for the knee bones. Towards this goal, 3D CT images of real knees, as well as a skeletal knee model with fat simulating Hoffa's pad, were acquired in both extension and flexion. Image segmentation was performed to automatically extract the real and simulated fat regions from the extension and flexion images. Utilizing the segmentation results as binary masks, we performed automatic multi-resolution image registration of the fat pad between flexed and extended knee positions. The resulting displacement fields from flexion-extension registration are examined and used to calculate local fat volume changes thus providing insight into shape changes that may have a mechanical component.

  15. Infra-patellar fat pad cysts: a case report and review of the literature

    PubMed Central

    Bisicchia, Salvatore; Savarese, Eugenio

    2012-01-01

    Summary Infra-patellar fat pad cysts are an uncommon type of intra-articular ganglia. We report a case of a young woman with a painful little mass in the anterior aspect of the left knee. Ultrasound revealed a multiloculate cyst, that was initially drained with a spinal needle. Four months later, she had a recurrence of symptoms and a ultrasound guided aspiration was performed. Cytological examination revealed synovial cells, synovial fluid, macrophages and debris: diagnosis was ganglion cyst. We reviewed the literature about infra-patellar fat pad cysts. Clinical diagnosis of an intraarticular cyst is very difficult, but sometimes an infra-patellar fat pad cyst could be suspected because it could be visible and palpable. MRI is the best diagnostic option in all cases. There are several treatment option, operative or conservative. In our opinion ultrasound guided aspiration is the treatment of choice in symptomatic ganglia, because it allows to drain all lacunae, preventing recurrence. PMID:23738315

  16. Rate-dependence of 'wet' biological adhesives and the function of the pad secretion in insects.

    PubMed

    Labonte, David; Federle, Walter

    2015-11-28

    Many insects use soft adhesive footpads for climbing. The surface contact of these organs is mediated by small volumes of a liquid secretion, which forms thin films in the contact zone. Here, we investigate the role of viscous dissipation by this secretion and the 'bulk' pad cuticle by quantifying the rate-dependence of the adhesive force of individual pads. Adhesion increased with retraction speed, but this effect was independent of the amount of pad secretion present in the contact zone, suggesting that the secretion's viscosity did not play a significant role. Instead, the rate-dependence can be explained by relating the strain energy release rate to the speed of crack propagation, using an established empirical power law. The 'wet' pads' behaviour was akin to that of 'dry' elastomers, with an equilibrium energy release rate close to that of dry van-der-Waals contacts. We suggest that the secretion mainly serves as a 'release layer', minimising viscous dissipation and thereby reducing the time- and 'loading-history'-dependence of the adhesive pads. In contrast to many commercial adhesives which derive much of their strength from viscous dissipation, we show that the major modulator of adhesive strength in 'wet' biological adhesive pads is friction, exhibiting a much larger effect than retraction speed. A comparison between 'wet' and 'dry' biological adhesives, using both results from this study and the literature, revealed a striking lack of differences in attachment performance under varying experimental conditions. Together, these results suggest that 'wet' and 'dry' biological adhesives may be more similar than previously thought. PMID:26376599

  17. KnotPad: Visualizing and Exploring Knot Theory with Fluid Reidemeister Moves.

    PubMed

    Zhang, Hui; Weng, Jianguang; Jing, Lin; Zhong, Yiwen

    2012-12-01

    We present KnotPad, an interactive paper-like system for visualizing and exploring mathematical knots; we exploit topological drawing and math-aware deformation methods in particular to enable and enrich our interactions with knot diagrams. Whereas most previous efforts typically employ physically based modeling to simulate the 3D dynamics of knots and ropes, our tool offers a Reidemeister move based interactive environment that is much closer to the topological problems being solved in knot theory, yet without interfering with the traditional advantages of paper-based analysis and manipulation of knot diagrams. Drawing knot diagrams with many crossings and producing their equivalent is quite challenging and error-prone. KnotPad can restrict user manipulations to the three types of Reidemeister moves, resulting in a more fluid yet mathematically correct user experience with knots. For our principal test case of mathematical knots, KnotPad permits us to draw and edit their diagrams empowered by a family of interactive techniques. Furthermore, we exploit supplementary interface elements to enrich the user experiences. For example, KnotPad allows one to pull and drag on knot diagrams to produce mathematically valid moves. Navigation enhancements in KnotPad provide still further improvement: by remembering and displaying the sequence of valid moves applied during the entire interaction, KnotPad allows a much cleaner exploratory interface for the user to analyze and study knot equivalence. All these methods combine to reveal the complex spatial relationships of knot diagrams with a mathematically true and rich user experience. PMID:26357111

  18. Vibro-Acoustic Analysis of NASA's Space Shuttle Launch Pad 39A Flame Trench Wall

    NASA Technical Reports Server (NTRS)

    Margasahayam, Ravi N.

    2009-01-01

    A vital element to NASA's manned space flight launch operations is the Kennedy Space Center Launch Complex 39's launch pads A and B. Originally designed and constructed In the 1960s for the Saturn V rockets used for the Apollo missions, these pads were modified above grade to support Space Shuttle missions. But below grade, each of the pad's original walls (including a 42 feet deep, 58 feet wide, and 450 feet long tunnel designed to deflect flames and exhaust gases, the flame trench) remained unchanged. On May 31, 2008 during the launch of STS-124, over 3500 of the. 22000 interlocking refractory bricks that lined east wall of the flame trench, protecting the pad structure were liberated from pad 39A. The STS-124 launch anomaly spawned an agency-wide initiative to determine the failure root cause, to assess the impact of debris on vehicle and ground support equipment safety, and to prescribe corrective action. The investigation encompassed radar imaging, infrared video review, debris transport mechanism analysis using computational fluid dynamics, destructive testing, and non-destructive evaluation, including vibroacoustic analysis, in order to validate the corrective action. The primary focus of this paper is on the analytic approach, including static, modal, and vibro-acoustic analysis, required to certify the corrective action, and ensure Integrity and operational reliability for future launches. Due to the absence of instrumentation (including pressure transducers, acoustic pressure sensors, and accelerometers) in the flame trench, defining an accurate acoustic signature of the launch environment during shuttle main engine/solid rocket booster Ignition and vehicle ascent posed a significant challenge. Details of the analysis, including the derivation of launch environments, the finite element approach taken, and analysistest/ launch data correlation are discussed. Data obtained from the recent launch of STS-126 from Pad 39A was instrumental in validating the

  19. Decarboxylation of Sorbic Acid by Spoilage Yeasts Is Associated with the PAD1 Gene▿

    PubMed Central

    Stratford, Malcolm; Plumridge, Andrew; Archer, David B.

    2007-01-01

    The spoilage yeast Saccharomyces cerevisiae degraded the food preservative sorbic acid (2,4-hexadienoic acid) to a volatile hydrocarbon, identified by gas chromatography mass spectrometry as 1,3-pentadiene. The gene responsible was identified as PAD1, previously associated with the decarboxylation of the aromatic carboxylic acids cinnamic acid, ferulic acid, and coumaric acid to styrene, 4-vinylguaiacol, and 4-vinylphenol, respectively. The loss of PAD1 resulted in the simultaneous loss of decarboxylation activity against both sorbic and cinnamic acids. Pad1p is therefore an unusual decarboxylase capable of accepting both aromatic and aliphatic carboxylic acids as substrates. All members of the Saccharomyces genus (sensu stricto) were found to decarboxylate both sorbic and cinnamic acids. PAD1 homologues and decarboxylation activity were found also in Candida albicans, Candida dubliniensis, Debaryomyces hansenii, and Pichia anomala. The decarboxylation of sorbic acid was assessed as a possible mechanism of resistance in spoilage yeasts. The decarboxylation of either sorbic or cinnamic acid was not detected for Zygosaccharomyces, Kazachstania (Saccharomyces sensu lato), Zygotorulaspora, or Torulaspora, the genera containing the most notorious spoilage yeasts. Scatter plots showed no correlation between the extent of sorbic acid decarboxylation and resistance to sorbic acid in spoilage yeasts. Inhibitory concentrations of sorbic acid were almost identical for S. cerevisiae wild-type and Δpad1 strains. We concluded that Pad1p-mediated sorbic acid decarboxylation did not constitute a significant mechanism of resistance to weak-acid preservatives by spoilage yeasts, even if the decarboxylation contributed to spoilage through the generation of unpleasant odors. PMID:17766451

  20. iPads and LCDs show similar performance in the detection of pulmonary nodules

    NASA Astrophysics Data System (ADS)

    McEntee, Mark F.; Lowe, Joanna; Butler, Marie Louise; Pietrzyk, Mariusz; Evanoff, Michael G.; Ryan, John; Brennan, Patrick C.; Rainford, Louise A.

    2012-02-01

    In February 2011 the University of Chicago Medical School distributed iPads to its trainee doctors for use when reviewing clinical information and images on the ward or clinics. The use of tablet computing devices is becoming widespread in medicine with Apple™ heralding them as "revolutionary" in medicine. The question arises, just because it is technical achievable to use iPads for clinical evaluation of images, should we do so? The current work assesses the diagnostic efficacy of iPads when compared with LCD secondary display monitors for identifying lung nodules on chest x-rays. Eight examining radiologists of the American Board of Radiology were involved in the assessment, reading chest images on both the iPad and the an off-the-shelf LCD monitor. Thirty chest images were shown to each observer, of which 15 had one or more lung nodules. Radiologists were asked to locate the nodules and score how confident they were with their decision on a scale of 1-5. An ROC and JAFROC analysis was performed and modalities were compared using DBM MRMC. The results demonstrate no significant differences in performance between the iPad and the LCD for the ROC AUC (p<0.075) or JAFROC FOM (p<0.059) for random readers and random cases. Sample size estimation showed that this result is significant at a power of 0.8 and an effect size of 0.05 for ROC and 0.07 for JAFROC. This work demonstrates that for the task of identifying pulmonary nodules, the use of the iPad does not significantly change performance compared to an off-the-shelf LCD.

  1. HPAEC-PAD quantification of Haemophilus influenzae type b polysaccharide in upstream and downstream samples.

    PubMed

    van der Put, Robert M F; de Haan, Alex; van den IJssel, Jan G M; Hamidi, Ahd; Beurret, Michel

    2015-11-27

    Due to the rapidly increasing introduction of Haemophilus influenzae type b (Hib) and other conjugate vaccines worldwide during the last decade, reliable and robust analytical methods are needed for the quantitative monitoring of intermediate samples generated during fermentation (upstream processing, USP) and purification (downstream processing, DSP) of polysaccharide vaccine components. This study describes the quantitative characterization of in-process control (IPC) samples generated during the fermentation and purification of the capsular polysaccharide (CPS), polyribosyl-ribitol-phosphate (PRP), derived from Hib. Reliable quantitative methods are necessary for all stages of production; otherwise accurate process monitoring and validation is not possible. Prior to the availability of high performance anion exchange chromatography methods, this polysaccharide was predominantly quantified either with immunochemical methods, or with the colorimetric orcinol method, which shows interference from fermentation medium components and reagents used during purification. Next to an improved high performance anion exchange chromatography-pulsed amperometric detection (HPAEC-PAD) method, using a modified gradient elution, both the orcinol assay and high performance size exclusion chromatography (HPSEC) analyses were evaluated. For DSP samples, it was found that the correlation between the results obtained by HPAEC-PAD specific quantification of the PRP monomeric repeat unit released by alkaline hydrolysis, and those from the orcinol method was high (R(2)=0.8762), and that it was lower between HPAEC-PAD and HPSEC results. Additionally, HPSEC analysis of USP samples yielded surprisingly comparable results to those obtained by HPAEC-PAD. In the early part of the fermentation, medium components interfered with the different types of analysis, but quantitative HPSEC data could still be obtained, although lacking the specificity of the HPAEC-PAD method. Thus, the HPAEC-PAD

  2. Toxicity and mutagenicity of low-metallic automotive brake pad materials.

    PubMed

    Malachova, Katerina; Kukutschova, Jana; Rybkova, Zuzana; Sezimova, Hana; Placha, Daniela; Cabanova, Kristina; Filip, Peter

    2016-09-01

    Organic friction materials are standardly used in brakes of small planes, railroad vehicles, trucks and passenger cars. The growing transportation sector requires a better understanding of the negative impact related to the release of potentially hazardous materials into the environment. This includes brakes which can release enormous quantities of wear particulates. This paper addresses in vitro detection of toxic and mutagenic potency of one model and two commercially available low-metallic automotive brake pads used in passenger cars sold in the EU market. The model pad made in the laboratory was also subjected to a standardized brake dynamometer test and the generated non-airborne wear particles were also investigated. Qualitative "organic composition" was determined by GC/MS screening of dichloromethane extracts. Acute toxicity and mutagenicity of four investigated sample types were assessed in vitro by bioluminescence assay using marine bacteria Vibrio fischeri and by two bacterial bioassays i) Ames test on Salmonella typhimurium His(-) and ii) SOS Chromotest using Escherichia coli PQ37 strain. Screening of organic composition revealed a high variety of organic compounds present in the initial brake pads and also in the generated non-airborne wear debris. Several detected compounds are classified by IARC as possibly carcinogenic to humans, e. g. benzene derivatives. Acute toxicity bioassay revealed a response of bacterial cells after exposure to all samples used. Phenolic resin and wear debris were found to be acutely toxic; however in term of mutagenicity the response was negative. All non-friction exposed brake pad samples (a model pad and two commercial pad samples) were mutagenic with metabolic activation in vitro. PMID:27179608

  3. Performance Analysis and Design Synthesis (PADS) computer program. Volume 3: User manual

    NASA Technical Reports Server (NTRS)

    1972-01-01

    The two-fold purpose of the Performance Analysis and Design Synthesis (PADS) computer program is discussed. The program can size launch vehicles in conjunction with calculus-of-variations optimal trajectories and can also be used as a general purpose branched trajectory optimization program. For trajectory optimization alone or with sizing, PADS has two trajectory modules. The first trajectory module uses the method of steepest descent. The second module uses the method of quasi-linearization, which requires a starting solution from the first trajectory module.

  4. STS-47 Endeavour, Orbiter Vehicle (OV) 105, lifts off from KSC LC 39 pad

    NASA Technical Reports Server (NTRS)

    1992-01-01

    STS-47 Endeavour, Orbiter Vehicle (OV) 105, lifts off from Kennedy Space Center (KSC) Launch Complex (LC) 39 pad at 10:23:00:0680 am (Eastern Daylight Time (EDT)). This profile view captures OV-105, its external tank (ET), and right solid rocket booster (SRB), just after space shuttle main engine and SRB firing and liftoff from the mobile launcher platform. The diamond shock effect is visible at the SSMEs. As OV-105 rises above the LC pad beginning its second trip into space, the fixed service structure (FSS) and retracted rotating service structure (RSS) are seen in the background. In the foreground, mobile lighting fixtures (spotlights) are visible.

  5. STS-104 crew takes part in emergency exit training at the pad

    NASA Technical Reports Server (NTRS)

    2001-01-01

    KENNEDY SPACE CENTER, Fla. -- On Launch Pad 39B, dressed in their launch and entry suits, STS-104 Mission Specialists (left to right) James F. Reilly, Janet Lynn Kavandi and Michael L. Gernhardt make their way from Space Shuttle Atlantis to the slidewire baskets, part of the emergency egress system at the pad. They and other crew members are taking part in Terminal Countdown Demonstration Test activities, which include the emergency egress training and a simulated countdown exercise. The launch of Atlantis on mission STS-104 is scheduled July 12. The mission is the 10th flight to the International Space Station and carries the Joint Airlock Module and High Pressure Gas Assembly.

  6. STS-102 crew gets emergency exit training at Launch Pad 39B during TCDT

    NASA Technical Reports Server (NTRS)

    2001-01-01

    KENNEDY SPACE CENTER, Fla. -- During emergency exit training on the Fixed Service Structure of Launch Pad 39B, STS-102 Mission Specialist Paul Richards takes a closer look at the lever that releases a slidewire basket, used for emergency exits from the launch pad, to the landing below. He and the rest of the crew are taking part in Terminal Countdown Demonstration Test activities, which include a simulated launch countdown. STS-102 is the eighth construction flight to the International Space Station, with Space Shuttle Discovery carrying the Multi-Purpose Logistics Module Leonardo. Launch on mission STS-102 is scheduled for March 8.

  7. Can Decommissioned Oil Pads in Boreal Alberta BE Reclaimed to Carbon Accumulating Peatlands?

    NASA Astrophysics Data System (ADS)

    Wieder, R.; Vitt, D. H.; Mowbray, S.

    2010-12-01

    In northern Alberta where peatland ecosystems are a dominant landscape feature, construction of oil drilling pads and access roads is a major disturbance. Reclamation of decommissioned oil pads has been hampered by the lack of research. At two decommissioned oil pads at Shell Oil’s Peace River Complex (northeastern Alberta), initially constructed in a bog/fen complex, we established a field experiment to assess reclamation approaches that could lead to a system reflecting undisturbed peatland structure (vegetation composition) and function (net carbon accumulation). In the fall of 2007, mineral soil was removed from two decommissioned pads in areas approximately 100-m x 30-m creating a mineral surface at or near the surrounding bog water table level. We established the following treatments: pad (fertilized vs. unfertilized); water table position (at and 5-cm above the surrounding bog water level); texture (tilling soil amendments into the mineral soil or not); amendment (controls; commercial peat, peat that had been stockpiled in a farmer’s field; landscape fabric; slough hay (native species hay from harvested from local farms), aspen wood chips); planting (in 1-m x 1-m subplots within 2-m x 2-m amendment plots: no planting, 9 Carex aquatilis plants, 5 C. aquatilis and 4 Salix lutea plants; 3 C. aquatilis, 3 S. lutea and 3 Larix laricina seedlings). Treatments were nested (planting within amendment, within texture, within water table level, within pad), with 6 replicate 2-m x 2-m plots of each amendment within each pad x texture x water level combination. Net CO2 exchange was quantified under a range of PAR conditions from full sunlight to complete darkness in each 1-m x 1-m planting subplot repeatedly during the summers of 2008, 2009 and 2010 using closed chambers and infrared gas analyzers. Both dark respiration and maximum net ecosystem production (NEPSAT; net CO2 sequestration when PAR>1000 μmol m-2 s-1) exhibited year x planting interactions (p<0.0001 and

  8. STS-32 Columbia, OV-102, liftoff from KSC LC Pad 39A

    NASA Technical Reports Server (NTRS)

    1990-01-01

    STS-32 Columbia, Orbiter Vehicle (OV) 102, its external tank (ET), and solid rocket boosters (SRBs) rise above the mobile launcher platform and begin to clear fixed service structure (FSS) tower (with rotating service structure (RSS) retracted) at Kennedy Space Center (KSC) Launch Complex (LC) Pad 39A. Liftoff occurred at 7:34:59:98 am Eastern Standard Time (EST) some 24 hours after dubious weather at the return-to-landing site (RTLS) had cancelled a scheduled launch. An exhaust cloud covers the launch pad. The firing SRBs and space shuttle main engines (SSMEs) are reflected in a nearby waterway. OV-102's launch is highlighted against the early morning darkness.

  9. STS-32 Columbia, OV-102, liftoff from KSC LC Pad 39A

    NASA Technical Reports Server (NTRS)

    1990-01-01

    STS-32 Columbia, Orbiter Vehicle (OV) 102, atop the external tank (ET) and flanked by two solid rocket boosters (SRBs) rises above the mobile launcher platform and is nearly clear of the fixed service structure (FSS) tower at Kennedy Space Center (KSC) Launch Complex (LC) Pad 39A. Plumes of smoke billow from the SRBs and cover the launch pad in a cloud. Liftoff occurred at 7:34:59:98 am Eastern Standard Time (EST) some 24 hours after dubious weather at the return-to-landing site (RTLS) had cancelled a scheduled launch. OV-102's launch is highlighted against the early morning darkness.

  10. Design of True Random One-Time Pads in DNA XOR Cryptosystem

    NASA Astrophysics Data System (ADS)

    Hirabayashi, Miki; Kojima, Hiroaki; Oiwa, Kazuhiro

    We present a new model to realize true random one-time pad (OTP) encryption using DNA self-assembly. OTP is an unbreakable cryptosystem if the pad (random key) is truly random, never reused, and kept secret. Mathematical algorithms can generate pseudo-random numbers only. "True" random numbers can be generated from a physical process such as thermal noise. In this work, we propose a new tile-colony algorithm that can utilize the DNA hybridization process as an effective source for the random key construction, and discuss the error tolerance of this method. Our results indicate that the molecular computation using DNA motifs will provide promising OTP applications.

  11. iPhones, iPads, and medical applications for antimicrobial stewardship.

    PubMed

    Goff, Debra A

    2012-07-01

    One of the most important antimicrobial stewardship activities of the infectious diseases pharmacist and physician is to provide education and clinical information about antimicrobials to health care professionals and patients; however, clinician training and continuing education in appropriate antimicrobial use in the United States are highly variable and nonstandardized. The iPhone, iPad, and the availability of more than 12,000 medical applications (referred to as "apps") allow stewardship programs the ability to integrate novel technology with point-of-care education. This article reviews medical apps for antimicrobial stewardship programs to use on the iPhone or iPad. PMID:22605544

  12. Heating Augmentation Due to Compression Pad Cavities on the Project Orion CEV Heat Shield

    NASA Technical Reports Server (NTRS)

    Hollis, Brian R.

    2009-01-01

    An experimental study has been conducted to assess the effects of compression pad cavities on the aeroheating environment of the Project Orion CEV heat-shield. Testing was conducted in Mach 6 and Mach 10 perfect-gas wind tunnels to obtain heating measurements in and around the compression pads cavities using global phosphor thermography. Data were obtained over a wide range of Reynolds numbers that produced laminar, transitional, and turbulent flow within and downstream of the cavities. The effects of cavity dimensions on boundary-layer transition and heating augmentation levels were studied. Correlations were developed for transition onset and for the average cavity-heating augmentation.

  13. The determination of the constitutive parameters of a medium with application to a reinforced concrete pad

    NASA Astrophysics Data System (ADS)

    Poggio, A. J.; Burke, G. L.; Pennock, S. T.

    1995-06-01

    This report describes the experimental and analytical efforts performed to determine the constitutive parameters of a reinforced concrete pad on which an aircraft (the NASA Boeing 757) was parked while its internal electromagnetic environment was measured. This concrete pad is part of the Large Electromagnetic System-Level Illuminator (LESLI) test facility at the Phillips Laboratory, Kirtland Air Force Base, New Mexico. The relative dielectric constant, conductivity, index of refraction, and reflection coefficient have been determined over the frequency range of 0 to 300 MHz and are presented.

  14. Space Shuttle Discovery leaves the VAB for Launch Pad 39B and mission STS-60

    NASA Technical Reports Server (NTRS)

    1994-01-01

    Leaving the Vehicle Asembly Building for Launch Pad 39A on a crisp, clear winter day, the Space Shuttle Discovery makes the final Earth-bound leg of a journey into space. Once at the pad, two of the payloads for Discovery's upcoming flight, mission STS- 60, will be installed. The Wake Shield Facility-1 and Get Away Special bridge assembly will be joining SPACEHAB-2 in the orbiter's payload bay. Liftoff of the first Space Shuttle flight of 1994 is currently targeted for around Feb. 3.{end}

  15. STS-38 Atlantis, OV-104, lifting off from KSC LC Pad during night launch

    NASA Technical Reports Server (NTRS)

    1990-01-01

    STS-38 Atlantis, Orbiter Vehicle (OV) 104, lifts off from Kennedy Space Center (KSC) Launch Complex Pad at 6:46:15:0639 pm (Eastern Standard Time (EST)). As OV-104, atop the external tank (ET) and flanked by two solid rocket boosters (SRBs), rises above the mobile launcher platform, exhaust smoke fills the area surrounding the launch pad. SRB and space shuttle main engine (SSME) firings glow against the night darkness and light up the fixed service structure (FSS) and retracted rotating service structure (RSS). STS-38 is a Department of Defense (DOD) devoted mission.

  16. Wireless pad-free integrated circuit debugging by powering modulation and lock-in infrared sensing

    NASA Astrophysics Data System (ADS)

    León, J.; Perpiñà, X.; Vellvehi, M.; Baldi, A.; Sacristán, J.; Jordà, X.

    2013-02-01

    In this work, non-functional radio frequency identification pad-free chips are analyzed by modulating its powering scheme and noninvasively sensing their surface infrared (IR) emission with an IR camera following lock-in strategies. This approach is justified by the chip wireless powering strategy and its pad-free design. As a result, latch-up triggering has been identified as the failure mechanism, also showing that electrical figures of merit can be extracted non-invasively (i.e., coils coupling frequency and its bandwidth).

  17. The determination of the constitutive parameters of a medium with application to a reinforced concrete pad

    NASA Technical Reports Server (NTRS)

    Poggio, A. J.; Burke, G. L.; Pennock, S. T.

    1995-01-01

    This report describes the experimental and analytical efforts performed to determine the constitutive parameters of a reinforced concrete pad on which an aircraft (the NASA Boeing 757) was parked while its internal electromagnetic environment was measured. This concrete pad is part of the Large Electromagnetic System-Level Illuminator (LESLI) test facility at the Phillips Laboratory, Kirtland Air Force Base, New Mexico. The relative dielectric constant, conductivity, index of refraction, and reflection coefficient have been determined over the frequency range of 0 to 300 MHz and are presented.

  18. Medical devices for restless legs syndrome – clinical utility of the Relaxis pad

    PubMed Central

    Mitchell, Ulrike H

    2015-01-01

    Restless Legs Syndrome or Willis–Ekbom Disease, a neurosensory disorder, can be treated with pharmaceuticals or conservatively. This review focuses on conservative treatments, more specifically on treatments with medical devices. Two modes of action, enhancement of circulation and counter stimulation, are introduced. Medical devices that use enhancement of circulation as their mechanism of action are whole body vibration, pneumatic compression, and near-infrared light. Medical devices that use counter stimulation include transcutaneous electrical nerve stimulation and the vibration Relaxis pad. The clinical utility of the Relaxis pad and its place in therapy is proposed. PMID:26664128

  19. Performance Analysis and Design Synthesis (PADS) computer program. Volume 1: Formulation

    NASA Technical Reports Server (NTRS)

    1972-01-01

    The program formulation for PADS computer program is presented. It can size launch vehicles in conjunction with calculus-of-variations optimal trajectories and can also be used as a general-purpose branched trajectory optimization program. In the former use, it has the Space Shuttle Synthesis Program as well as a simplified stage weight module for optimally sizing manned recoverable launch vehicles. For trajectory optimization alone or with sizing, PADS has two trajectory modules. The first trajectory module uses the method of steepest descent; the second employs the method of quasilinearization, which requires a starting solution from the first trajectory module.

  20. Using iPads to illustrate the impulse-momentum relationship

    NASA Astrophysics Data System (ADS)

    Streepey, Jefferson W.

    2013-01-01

    One of the fundamental challenges in teaching is making the students able to transform course material in ways that help them solve "real world" problems. Sophisticated mobile technology (such as smartphones, iPads, or iTouches) offers students an opportunity to apply physics content to a broad range of scenarios to enhance their understanding and improve their class engagement. For the outlined example, students in an upper-level biomechanics class used the native accelerometers in iPads to record and analyze human movement. This activity allowed the students to experiment with the impulse-momentum relationship.