Science.gov

Sample records for 1-butyl-3-methylimidazolium hexafluorophosphate c4mimpf6

  1. Enzymatic synthesis of poly-L-lactide-co-glycolide in the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate.

    PubMed

    Mena, María; Chanfreau, Sébastien; Gimeno, Miquel; Bárzana, Eduardo

    2010-11-01

    This article reports the lipase-catalyzed ring-opening copolymerization of L-lactide (LLA) and glycolide using the commercially available ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate as solvent media. Candida antarctica lipase B, immobilized in an acrylic support was used as biocatalyst. The reaction temperature had a direct influence on yields and molecular weights of the copolymers as well as LLA incorporation. The materials presented semi-crystalline structures assessed by DSC and powder XR diffraction analyses. PMID:20490553

  2. Transport properties of binary mixtures of carbon dioxide and 1-butyl-3-methylimidazolium hexafluorophosphate studied by transient grating spectroscopy.

    PubMed

    Demizu, Masashi; Terazima, Masahide; Kimura, Yoshifumi

    2008-10-01

    Transient grating spectroscopy was applied to measurements of sound velocity and thermal diffusivity in binary mixture solutions of carbon dioxide (CO(2)) and 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIm][PF(6)]) along the saturated line of CO(2) at 40 degrees C up to 20.0 MPa. The sound velocity decreased more than 10% by increasing the pressure to 10 MPa, and the pressure effect was very small above 10 MPa. The change in the thermal diffusivity was small. The translational diffusion coefficients of carbon monoxide, diphenylacetylene (DPA), and diphenylcyclopropenone (DPCP) were also determined. The diffusion coefficients increased up to 10 MPa, and the pressure effect was almost saturated above 10 MPa. The pressure dependence of the diffusion coefficients of DPCP and DPA was larger than that of carbon monoxide. The results are discussed in relation with the viscosity change caused by applying pressure. PMID:18845895

  3. Catalytic activities of fungal oxidases in hydrophobic ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate-based microemulsion.

    PubMed

    Zhou, Gui-Ping; Zhang, Yun; Huang, Xi-Rong; Shi, Chuan-Hong; Liu, Wei-Feng; Li, Yue-Zhong; Qu, Yin-Bo; Gao, Pei-Ji

    2008-10-01

    For hydrophobic ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF(6)]), an H(2)O-in-[BMIM][PF(6)] microemulsion could be formed in the presence of nonionic surfactant Triton X-100 (TX-100). In such a medium, both lignin peroxidase (LiP) and laccase could express their catalytic activity with the optimum molar ratio of H(2)O to TX-100 at 8.0 for LiP and >20 for laccase, and the optimum pH values at 3.2 for LiP and 4.2 for laccase, respectively. As compared with pure or water saturated [BMIM][PF(6)], in which the two oxidases had negligible catalytic activity due to the strong inactivating effect of [BMIM][PF(6)] on both enzymes, the use of the [BMIM][PF(6)]-based microemulsion had some advantages. Not only the catalytic activities of both fungal oxidases greatly enhanced, but also the apparent viscosity of the medium decreased. PMID:18602799

  4. NMR study of cation dynamics in three crystalline states of 1-butyl-3-methylimidazolium hexafluorophosphate exhibiting crystal polymorphism.

    PubMed

    Endo, Takatsugu; Murata, Hiroki; Imanari, Mamoru; Mizushima, Noriko; Seki, Hiroko; Nishikawa, Keiko

    2012-03-29

    We investigate the cation rotational dynamics of a room temperature ionic liquid (RTIL) 1-butyl-3-methylimidazolium hexafluorophosphate ([C(4)mim]PF(6)) in its three crystalline states by (1)H NMR spectroscopy. Spin-lattice and spin-spin relaxation time (T(1) and T(2), respectively) measurements as a function of temperature confirm the presence of three polymorphic crystals of [C(4)mim]PF(6): crystals α, β, and γ, which we previously discovered using Raman spectroscopy and calorimetry. Second moment calculations of (1)H NMR spectra reveal that certain segmental motions of the butyl group in addition to the rapid rotation of the two methyl groups in the cation occur in all the crystals. The trend in the mobility of the segmental motions is γ < β ≤ α, which is consistent with the strength of cation-anion interactions (or crystal packing density) estimated from high-frequency Raman scattering experiments. T(1) measurements demonstrate two types of rotational motions on the nanosecond time scale in all three crystals: fast and slow motions. The three crystals have similar activation energies of 12.5-15.1 kJ mol(-1) for the fast motion, which is assigned to the rotation of the methyl group at the terminal of the butyl group. These observed activation energies were consistent with that estimated by quantum chemical calculations in the gas phase (11.9 kJ mol(-1)). In contrast, the slow motions of crystals α and γ are attributed to different segmental motions of the butyl group and that of crystal β to either a little segmental motion or a certain PF(6)(-) rotational motion. These nanosecond rotational motions obtained from the T(1) measurements do not appear to be affected by crystal packing density because local interactions in the crystalline state rather than packing density govern such nanosecond motions. With respect to the segmental motions, the mobility is likely to change significantly with the conformation of the butyl group. On the basis of these

  5. Mechanical exfoliation of graphite in 1-butyl-3-methylimidazolium hexafluorophosphate (BMIM-PF6) providing graphene nanoplatelets that exhibit enhanced electrocatalysis

    NASA Astrophysics Data System (ADS)

    Hayes, William Ignatius; Lubarsky, Gennady; Li, Meixian; Papakonstantinou, Pagona

    2014-12-01

    A novel production method for graphene nanoplatelets (GPs) with enhanced electrocatalytic behaviour is presented. GPs show improvement in their oxygen reduction reaction (ORR) catalysis after prolonging the grinding of graphite in 1-butyl-3-methylimidazolium hexafluorophosphate (BMIM-PF6). Nitrogen doping of the GPs has inferred a further increase in ORR. The ORR onset potential, cathodic current magnitude and electron transfer efficiency have all improved as a direct consequence of increasing the graphite grinding duration from 30 min to 4 h. Atomic force microscopy has confirmed a decrease in the GP diameter and height as the grinding increases. Raman spectroscopy indicates a higher level of defects present after prolonging the graphite grinding in BMIM-PF6, most likely a result of the increased edge plane exposure. This increased edge plane appears to promote a higher level of nitrogen incorporation as the graphite grinding duration increases, as confirmed by X-ray photoelectron spectroscopy analysis. The stability of the cathodic current assessed by chronoamperometry analysis is higher for the GP and nitrogen doped graphene nanoplatelet (N-GP) samples than the platinum on carbon black (Pt/C). This study presents a novel process for the production of nitrogen doped graphene nanoplatelets, constituting a strategy for the up-scaled production of electrocatalysts.

  6. Intramolecular Excimer Formation Dynamics of 1,3-Bis-(1-pyrenyl)propane within 1-Butyl-3-methylimidazolium Hexafluorophosphate and Its Polyethylene Glycol Mixtures.

    PubMed

    Yadav, Anita; Kurur, Narayanan D; Pandey, Siddharth

    2015-10-22

    Mixtures of ionic liquid with polyethylene glycol (PEG) have shown interesting features as solubilizing media. Intramolecular excimer formation dynamics of 1,3-bis-(1-pyrenyl)propane [1Py(3)1Py] is investigated within mixtures of a common and popular ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF6]) with PEGs of average molecular weight (MW) 200 (PEG200), average MW 400 (PEG400), number-average MW Mn 570-630 (PEG600), and number-average MW Mn 950-1050 (PEG1000) over the complete composition range at a 10° interval in the temperature range 10-90 °C. Irrespective of the composition of the medium and the temperature, excited-state intensity decay of the excimer fluorescence best fits to a three-exponential decay function, suggesting the presence of one excited-state monomer and two kinetically distinguishable excimers where both excimers are populated simultaneously by the excited monomer with no interconversion between the two excimers. In neat PEGs for temperatures ≤ 50 °C, intensity decay data of monomer fluorescence best fits to a single-exponential decay function, which implies the dissociation of both excimers back to the monomer to be insignificant. As the temperature is increased, the fits become closer to a double-exponential decay function, implying dissociation of one of the excimers to become significant. In neat [bmim][PF6], while a double-exponential decay function is required to fit the monomer excited-state intensity decay data at lower temperatures, three exponentials are required to satisfactorily fit the data at higher temperatures, suggesting both excimers significantly dissociate back to the monomer at higher temperatures within the ionic liquid. Within long-chain PEG-containing ([bmim][PF6] + PEG) mixtures, PEG as opposed to [bmim][PF6] controls the excimer formation dynamics by supposedly wrapping around the excimer, thus hindering dissociation back to the monomer. The overall rate constant of the excimer formation

  7. Solid phase extraction of cadmium on 2-mercaptobenzothiazole loaded on sulfur powder in the medium of ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate and cold vapor generation-atomic absorption spectrometric determination.

    PubMed

    Pourreza, N; Ghanemi, K

    2010-06-15

    A novel solid phase extractor for preconcentration of cadmium at ng L(-1) levels has been developed. Cadmium ions were retained on a column packed with sulfur powder modified with 2-mercaptobenzothiazole (2-MBT) in the medium of 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim](+)PF(6)(-)) ionic liquid. The presence of ionic liquid during modification of sulfur enhanced the retention of cadmium ions on the column. The retained cadmium ions were eluted with 2 mol L(-1) solution of HCl and measured by cold vapor generation-atomic absorption spectrometry (CVG-AAS). By using reaction cell-gas liquid separator (RC-GLS), gaseous cadmium vapors were produced and reached the atomic absorption spectrometer, instantaneously. The influence of different variables on both processes of solid phase extraction and CVG-AAS determination of cadmium ions was investigated. The calibration curve was linear in the range of 10-200 ng L(-1)of cadmium in the initial solution with r=0.9992 (n=8) under optimum conditions. The limit of detection based on three times the standard deviation of the blank (3S(b), n=10) was 4.6 ng L(-1). The relative standard deviation (R.S.D.) of 25 and 150 ng L(-1) of cadmium was 4.1 and 2.2% (n=8), respectively. The procedure was validated by the analysis of a certified reference material (DORM-3), water and fish samples. PMID:20176439

  8. Interaction of ionic liquid with water in ternary microemulsions (Triton X-100/water/1-butyl-3-methylimidazolium hexafluorophosphate) probed by solvent and rotational relaxation of coumarin 153 and coumarin 151.

    PubMed

    Seth, Debabrata; Chakraborty, Anjan; Setua, Palash; Sarkar, Nilmoni

    2006-08-29

    The interaction of ionic liquid with water in 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF6])/Triton X-100 (TX-100)/H2O ternary microemulsions, i.e., "[bmim][PF6]-in-water" microregions of the microemulsions, has been studied by the dynamics of solvent and rotational relaxation of coumarin 153 (C-153) and coumarin 151 (C-151). The variation of the time constants of solvent relaxation of C-153 is very small with an increase in the [bmim][PF6]/TX-100 ratio (R). The rotational relaxation time of C-153 also remains unchanged in all micremulsions of different R values. The invariance of solvation and rotational relaxation times of C-153 indicates that the position of C-153 remains unaltered with an increase in R and probably the probe is located at the interfacial region of [bmim][PF6] and TX-100 in the microemulsions. On the other hand, in the case of C-151, with an increase in R the fast component of the solvation time gradually increases and the slow component gradually decreases, although the change in solvation time is small in comparison to that of microemulsions containing common polar solvents such as water, methanol, acetonitrile, etc. The rotational relaxation time of C-151 increases with an increase in R. This indicates that with an increase in the [bmim][PF6] content the number of C-151 molecules in the core of the microemulsions gradually increases. In general, the solvent relaxation time is retarded in this room temperature ionic liquid/water-containing microemulsion compared to that of a neat solvent, although retardation is very small compared to that of the solvent relaxation time of the conventional solvent in the core of the microemulsions. PMID:16922562

  9. Characterization of cellulose II nanoparticles regenerated from ionic liquid, 1-butyl-3-methylimidazolium chloride

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Regenerated cellulose nanoparticles (RCNs) including both elongated fiber and spherical structures were prepared from microcrystalline cellulose (MCC)and cotton using 1-butyl-3-methylimidazolium chloride followed by high-pressure homogenization. The crystalline structure of RCNs was cellulose II in ...

  10. MICROWAVE-ASSISTED PREPARATION OF 1-BUTYL-3-METHYLIMIDAZOLIUM TETRACHLOROGALLATE AND ITS CATALYTIC USE IN ACETAL FORMATION UNDER MILD CONDITIONS

    EPA Science Inventory

    1-Butyl-3-methylimidazolium tetrachlorogallate, [bmim][GaCl4], prepared via microwave-assisted protocol, is found to be an active catalyst for the efficient acetalization of aldehydes under mild conditions.

  11. Reductive splitting of cellulose in the ionic liquid 1-butyl-3-methylimidazolium chloride.

    PubMed

    Ignatyev, Igor A; Van Doorslaer, Charlie; Mertens, Pascal G N; Binnemans, Koen; De Vos, Dirk E

    2010-01-01

    The depolymerization of cellulose is carried out in the ionic liquid 1-butyl-3-methylimidazolium chloride in the presence of hydrogen gas. First, the ketal 1,1-diethoxycyclohexane and cellobiose were used as model substrates. For the depolymerization of cellulose itself, the combination of a heterogeneous metal catalyst and a homogeneous ruthenium catalyst proved effective. One of the possible roles of the ruthenium compound is to enhance the transfer of hydrogen to the metallic surface. The cellulose is fully converted under relatively mild conditions, with sorbitol as the dominant product in 51-74% yield. PMID:20049766

  12. Electron density analysis of 1-butyl-3-methylimidazolium chloride ionic liquid.

    PubMed

    del Olmo, Lourdes; Morera-Boado, Cercis; López, Rafael; García de la Vega, José M

    2014-06-01

    An analysis of the electron density of different conformers of the 1-butyl-3-methylimidazolium chloride (bmimCl) ionic liquid by using DFT through the BVP86 density functional has been obtained within the framework of Bader's atom in molecules (AIM), localized orbital locator (LOL), natural bond orbital (NBO), and deformed atoms in molecules (DAM). We also present an analysis of the reduced density gradients that deliver the non-covalent interaction regions and allow to understand the nature of intermolecular interactions. The most polar conformer can be characterized as ionic by AIM, LOL, and DAM methods while the most stable and the least polar shows shared-type interactions. The NBO method allows to comprehend what causes the stabilization of the most stable conformer based on analysis of the second-order perturbative energy and the charge transferred among the natural orbitals involved in the interaction. PMID:24878801

  13. Characterization of cellulose II nanoparticles regenerated from 1-butyl-3-methylimidazolium chloride.

    PubMed

    Han, Jingquan; Zhou, Chengjun; French, Alfred D; Han, Guangping; Wu, Qinglin

    2013-05-15

    Regenerated cellulose nanoparticles (RCNs) including both elongated fiber and spherical structures were prepared from microcrystalline cellulose (MCC) and cotton using 1-butyl-3-methylimidazolium chloride followed by high-pressure homogenization. The crystalline structure of RCNs was cellulose II in contrast to the cellulose I form of the starting materials. Also, the RCNs have decreased crystallinity and crystallite size. The elongated RCNs produced from cotton and MCC had average lengths of 123 ± 34 and 112 ± 42 nm, and mean widths of 12 ± 5 and 12 ± 3 nm, respectively. The average diameter of spherical RCNs from MCC was 118 ± 32nm. The dimensions of the various RCNs were all well fitted with an asymmetrical log-normal distribution function. The RCN has a two-step pyrolysis, different from raw MCC and cotton that have a one-step process. PMID:23544632

  14. Green polymer electrolytes based on chitosan and 1-butyl-3-methylimidazolium acetate

    SciTech Connect

    Shamsudin, Intan Juliana; Ahmad, Azizan; Hassan, Nur Hasyareeda

    2014-09-03

    Green polymer electrolytes based on chitosan as the polymer matrix and ionic liquid 1-butyl-3-methylimidazolium acetate [Bmim][OAc] as charge carriers were prepared by solution casting technique. Complexes with various amount of ionic liquid loading were investigated as possible ionic conducting polymers. The ionic conductivity was found to increase with increasing weight percent of ionic liquid. The highest ionic conductivity of the charged chitosan-[Bmim][OAc] was 2.44 × 10{sup −3} S cm{sup −1} at 90 wt.% of [Bmim][OAc] content at ambient temperature. Attenuated Total Reflection Fourier Transform infrared (ATR-FTIR) spectroscopy has proven the interaction between chitosan and [Bmim][OAc]. X-ray Diffraction (XRD) has shown that the amorphosity of the complexes increase as the amount of [Bmim][OAc] increase.

  15. Synthesis, characterization, and application of 1-butyl-3-methylimidazolium thiocyanate for extractive desulfurization of liquid fuel.

    PubMed

    Dharaskar, Swapnil A; Wasewar, Kailas L; Varma, Mahesh N; Shende, Diwakar Z

    2016-05-01

    1-Butyl-3-methylimidazolium thiocyanate [BMIM]SCN has been presented on extractive desulfurization of liquid fuel. The FTIR, (1)H-NMR, and C-NMR have been discussed for the molecular confirmation of synthesized [BMIM]SCN. Further, thermal, conductivity, moisture content, viscosity, and solubility analyses of [BMIM]SCN were carried out. The effects of time, temperature, sulfur compounds, ultrasonication, and recycling of [BMIM]SCN on removal of dibenzothiophene from liquid fuel were also investigated. In extractive desulfurization, removal of dibenzothiophene in n-dodecane was 86.5 % for mass ratio of 1:1 in 30 min at 30 °C under the mild process conditions. [BMIM]SCN could be reused five times without a significant decrease in activity. Also, in the desulfurization of real fuels, multistage extraction was examined. The data and results provided in the present paper explore the significant insights of imidazolium-based ionic liquids as novel extractant for extractive desulfurization of liquid fuels. PMID:26139406

  16. Novel Electroactive-paper Gel Preparations via 1-butyl-3-methylimidazolium chloride (BMIMCl) Solvent

    NASA Astrophysics Data System (ADS)

    Kunchornsup, Wissawin; Sirivat, Anuvat

    2010-03-01

    Papers used in the field of electro-responsive applications are known as Electroactive-papers (EAPaps), consisting primarily of a cellulose. 1-butyl-3-methylimidazolium chloride (BMIMCl) is an interesting ionic liquid that acts as an effective cellulose solvent for EAPap due to its high solubility without chain derivatization, less chain degradation, and stability in electro-responsive applications. In our work, physical and chemical cellulose gels were fabricated and studied for the effects of varying crosslinking ratio (CR) and aging time (tag), with glutaraldehyde (GA) acting as the crosslinking agent. The crosslinking reaction conversion could be increased by increasing the CR and tag; the reaction products are ketone linkages and by-product water molecules. A difference in optical properties could be observed and related to the differing amounts of ketone linkages, as confirmed by FTIR-ATR, and the degradation temperature (Td). Our paper-gels showed potential characteristics towards electro-responsive applications: less preparation time (< 14 hours) and stable gel properties.

  17. DFT study of 1-butyl-3-methylimidazolium salicylate: a third-generation ionic liquid.

    PubMed

    Armaković, Stevan; Armaković, Sanja J; Vraneš, Milan; Tot, Aleksandar; Gadžurić, Slobodan

    2015-09-01

    A detailed theoretical investigation of the third-generation ionic liquid (IL) 1-butyl-3-methylimidazolium salicylate ([BMIM][Sal]), performed within the framework of density functional theory (DFT), is presented in this paper. The B3LYP-D3, M06-2X, and M06-2X-D3 functionals were used to obtain the equilibrium geometries of the two ions [BMIM](+) and [Sal](-). It is shown that the equilibrium ion geometries obtained with the dispersion-corrected B3LYP functional are very close to the ion geometries obtained with the M06-2X and M06-2X-D3 functionals. Global reactivity was assessed using molecular orbital theory and quantum molecular descriptors. Molecular electrostatic potential (MEP) surfaces and average local ionization energy (ALIE) surfaces were created in order to elucidate the charge distribution and reactivity of the investigated IL. Ion-pair binding energies were calculated with all three functionals, and the results confirmed the presence of a strong electrostatic interaction between the ions, while further insight into the interactions between the two ions was obtained by analyzing noncovalent interactions based on the reduced density gradient (RDG) surface, which revealed a total of nine interactions between the ions. Finally, the aromaticity of each ion was investigated by calculating the nucleus-independent chemical shift (NICS) parameter, which indicated that significant changes in the charge delocalization on each ion occur when the two ions interact. PMID:26318199

  18. Electrodeposition of Nanocrystalline Chromium Coatings Based on 1-Butyl-3-Methylimidazolium-Bromide Ionic Liquid.

    PubMed

    He, Xinkuai; Zhu, Qingyun; Hou, Bailong; Cai, Youxing; Li, Chen; Fu, Liqin; Wu, Luye

    2015-12-01

    The electrochemical behavior of trivalent chromium reduction from 1-butyl-3-methylimidazolium-bromide ([BMIM]Br) ionic liquid is studied. The result of cyclic voltammetry shows that the Cr(III) reduction is irreversible and occurs in two steps, Cr(III)to Cr(II), and Cr(II) to Cr(0), respectively. In the electrochemical impedance spectroscopy measurements, the preferable equivalent circuit is made to fit the experimental data. The effects of electroplating parameters on coating thickness and electrodepositon rate are investigated by potentiostatic method on Cu electrode from Cr(III)-[BMIM]Br solution. The results show that the temperature and depositing potential have great effect on the coating thickness and electrodeposition rate. The surface morphology and composition of deposited Cr are investigated using scanning electron microscope (SEM) and energy-dispersive spectroscopy (EDS). SEM analysis shows that chromium electrodeposits obtained on Cu electrodes present a ball-like structure. EDS analysis shows that the coatings are composed of Cr. Moreover, the corrosion resistance of the as-deposited chromium layer is evaluated using polarization curves. The results show that the corrosion resistance of the chromium coatings obtained at higher potential is better. PMID:26682363

  19. Local Structure in Terms of Nearest-Neighbor Approach in 1-Butyl-3-methylimidazolium-Based Ionic Liquids: MD Simulations.

    PubMed

    Marekha, Bogdan A; Koverga, Volodymyr A; Chesneau, Erwan; Kalugin, Oleg N; Takamuku, Toshiyuki; Jedlovszky, Pál; Idrissi, Abdenacer

    2016-06-01

    Description of the local microscopic structure in ionic liquids (ILs) is a prerequisite to obtain a comprehensive understanding of the influence of the nature of ions on the properties of ILs. The local structure is mainly determined by the spatial arrangement of the nearest neighboring ions. Therefore, the main interaction patterns in ILs, such as cation-anion H-bond-like motifs, cation-cation alkyl tail aggregation, and ring stacking, were considered within the framework of the nearest-neighbor approach with respect to each particular interaction site. We employed classical molecular dynamics (MD) simulations to study in detail the spatial, radial, and orientational relative distribution of ions in a set of imidazolium-based ILs, in which the 1-butyl-3-methylimidazolium (C4mim(+)) cation is coupled with the acetate (OAc(-)), chloride (Cl(-)), tetrafluoroborate (BF4(-)), hexafluorophosphate (PF6(-)), trifluoromethanesulfonate (TfO(-)), or bis(trifluoromethanesulfonyl)amide (TFSA(-)) anion. It was established that several structural properties are strongly anion-specific, while some can be treated as universally applicable to ILs, regardless of the nature of the anion. Namely, strongly basic anions, such as OAc(-) and Cl(-), prefer to be located in the imidazolium ring plane next to the C-H(2/4-5) sites. By contrast, the other four bulky and weakly coordinating anions tend to occupy positions above/below the plane. Similarly, the H-bond-like interactions involving the H(2) site are found to be particularly enhanced in comparison with the ones at H(4-5) in the case of asymmetric and/or more basic anions (C4mimOAc, C4mimCl, C4mimTfO, and C4mimTFSA), in accordance with recent spectroscopic and theoretical findings. Other IL-specific details related to the multiple H-bond-like binding and cation stacking issues are also discussed in this paper. The secondary H-bonding of anions with the alkyl hydrogen atoms of cations as well as the cation-cation alkyl chain

  20. Influence of counterions on micellization of tetramethylammonium perfluorononanoic carboxylate in 1-butyl-3-methylimidazolium ionic liquid.

    PubMed

    Long, Panfeng; Chen, Jingfei; Wang, Dong; Hu, Ziqi; Gao, Xuedong; Li, Ziran; Hao, Jingcheng

    2012-07-01

    The influence of counterions on micellization of perfluorononanoic carboxylate ammonium salts in water and 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim]BF(4)) solutions was investigated by surface tension and (19)F NMR measurements and freeze-fracture transmission electron microscopy (FF-TEM) observations. Changes in the counterions of the fluorocarbon surfactants have different effects on the two solvents. With the increase of counterion volume, the critical micelle concentration (cmc) value of relevant fluorinated surfactant decreases in aqueous solutions. This is because the counterions with larger size, such as (+)N(CH(3))(4), can be little hydrated, which can screen the electrostatic repulsion of the headgroups of the fluorocarbon surfactant and thus facilitate micelle formation. However, the fluorocarbon surfactants can dissolve and form micelles in [bmim]BF(4) only when they provide with largest counterion such as (+)N(CH(3))(4). This is because the counterion, (+)N(CH(3))(4), disperses the charge of the cations, which could weaken the electrostatic interaction between the ion pair of the surfactant, leading to a higher degree of counterion binding. The thermodynamic parameters estimated from the temperature dependence of the cmc values tell us that the micelle formation for tetramethylammonium perfluorononanoic carboxylate (C(8)F(17)COON(CH(3))(4), PFNT) in ionic liquids (ILs) is an entropy-driven process at low temperature but an enthalpy-driven process at high temperature. The driving force of the micellization for fluorocarbon surfactants in [bmim]BF(4) is the solvophobic effect, due to the hydrophobic and oleophobic properties of fluorocarbon chains. PMID:22690854

  1. Rapid dissolution of switchgrass in 1-butyl-3-methylimidazolium chloride by ultrasonication.

    PubMed

    Montalbo-Lomboy, Melissa; Grewell, David

    2015-01-01

    The utilization of ultrasonics to rapidly dissolve switchgrass in ionic liquid, 1-butyl-3-methylimidazolium chloride ([Bmim][Cl]) was evaluated in this work. The objective of the study focused on determining the effects of various ultrasonic conditions on the recovery of carbohydrate from biomass, lignin removal, and enzymatic hydrolysis. Dried ground switchgrass was added to ionic liquid, then sonicated at a frequency of 20kHz. The experiments were conducted using a catenoidal horn at varying amplitudes of 96μm, 128μm, and 160μm and sonication times of 2, 3, and 4min. Similarly, ground switchgrass was dissolved in ionic liquid assisted by conventional heat treatment at 130°C for 12 and 24h. The results showed good delignification results of 53% for the 24h heat pretreated samples and of 50.8% for ultrasonic assisted samples at 160μm amplitude and 4min. Even in the presence of lignin in the recovered biopolymer, both of heat treated and ultrasonicated samples obtained 100% glucan digestibility after only 3h of enzymatic hydrolysis. Heat pretreated samples exhibited 44-59% lower xylan digestibility compared to ultrasonic pretreated samples (160μm amplitude and 4min sonication time). Scanning electron microscope images displayed significant changes in biomass structure from intact and crystalline of the untreated biomass to disintegrated and amorphous of the treated biomass (heat treated and ultrasonicated). With increasing ultrasonic amplitude the carbohydrate recovery decreased. Also, more than 50% of the hemicellulose fraction was lost during biomass recovery. Overall, it was concluded that ultrasonication was a promising technology to enhance dissolution of lignocellulose in ionic liquid. PMID:25041976

  2. Multiprobe Spectroscopic Inverstigation of Molecular-level Behavior within Aqueous 1-Butyl-3-methylimidazolium Tetrafluoroborate

    SciTech Connect

    Sarkar, Abhra; Ali, Maroof; Baker, Gary A; Tetin, Sergey Y.; Ruan, Qiaoqiao; Pandey, Siddharth

    2009-01-01

    In this work, an array of molecular-level solvent featuressincluding solute-solvent/solvent-solvent interactions, dipolarity, heterogeneity, dynamics, probe accessibility, and diffusionswere investigated across the entire composition of ambient mixtures containing the ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate, [bmim][BF4], and pH 7.0 phosphate buffer, based on results assembled for nine different molecular probes utilized in a range of spectroscopic modes. These studies uncovered interesting and unusual solvatochromic probe behavior within this benchmark mixture. Solvatochromic absorbance probessa watersoluble betaine dye (betaine dye 33), N,N-diethyl-4-nitroaniline, and 4-nitroanilineswere employed to determine ET (a blend of dipolarity/polarizability and hydrogen bond donor contributions) and the Kamlet-Taft indices * (dipolarity/polarizability), R (hydrogen bond donor acidity), and (hydrogen bond acceptor basicity) characterizing the [bmim][BF4] + phosphate buffer system. These parameters each showed a marked deviation from ideality, suggesting selective solvation of the individual probe solutes by [bmim][BF4]. Similar conclusions were derived from the responses of the fluorescent polarity-sensitive probes pyrene and pyrene-1-carboxaldehyde. Importantly, the fluorescent microfluidity probe 1,3-bis(1-pyrenyl)propane senses a microviscosity within the mixture that significantly exceeds expectations derived from simple interpolation of the behavior in the neat solvents. On the basis of results from this probe, a correlation between microviscosity and bulk viscosity was established; pronounced solvent-solvent hydrogen-bonding interactions were implicit in this behavior. The greatest deviation from ideal additive behavior for the probes studied herein was consistently observed to occur in the buffer-rich regime. Nitromethane-based fluorescence quenching of pyrene within the [bmim][BF4] + phosphate buffer system showed unusual compliance with a sphere

  3. Rotational diffusion of neutral and charged solutes in 1-butyl-3-methylimidazolium-based ionic liquids: influence of the nature of the anion on solute rotation.

    PubMed

    Karve, Lalita; Dutt, G B

    2012-02-16

    Temperature-dependent fluorescence anisotropies of two organic solutes, 2,5-dimethyl-1,4-dioxo-3,6-diphenylpyrrolo[3,4-c]pyrrole (DMDPP) and rhodamine 110 (R110), have been measured in 1-butyl-3-methylimidazolium ([bmim(+)])-based ionic liquids containing the anions hexafluorophosphate ([PF(6)(-)]), bis(trifluoromethylsulfonyl)imide ([Tf(2)N(-)]), tetrafluoroborate ([BF(4)(-)]), trifluoromethanesulfonate ([TfO(-)]), and nitrate ([NO(3)(-)]). This data has been used in conjunction with the recently published results (Dutt, G. B. J. Phys. Chem. B2010, 114, 8971) for the same solutes in [bmim(+)] tris(pentafluoroethyl)trifluorophosphate ([FAP(-)]) to understand the influence of various anions on solute rotation. The boundary condition parameter C(obs), which has been obtained from the analysis of the data using Stokes-Einstein-Debye hydrodynamic theory, for the neutral solute DMDPP is more or less the same in all the ionic liquids. Moreover, C(obs) values are close to the predictions of slip boundary condition, which indicates that solvent viscosity alone governs the rotation of DMDPP. In contrast, for R110, which experiences specific interactions with the anions of the ionic liquids, the C(obs) values are close to stick hydrodynamics. It has also been noticed that the C(obs) values vary with the nature of the anion and this variation correlates with the hydrogen bond basicities of the anions of the ionic liquids. PMID:22233259

  4. Glycine in 1-butyl-3-methylimidazolium acetate and trifluoroacetate ionic liquids: effect of fluorination and hydrogen bonding.

    PubMed

    Podgoršek, Ajda; Macchiagodena, Marina; Ramondo, Fabio; Costa Gomes, Margarida F; Pádua, Agílio A H

    2012-05-14

    The solvation of glycine in two ionic liquids (ILs), namely, 1-butyl-3-methylimidazolium acetate, [C(1)C(4)Im][OAc], and 1-butyl-3-methylimidazolium trifluoroacetate, [C(1)C(4)Im][TFA], was studied by a combination of experimental and theoretical methods. The solubility of glycine in both ILs was determined at 333.15 K to be (8.1±0.5) and (1.0±0.5) wt % in [C(1)C(4)Im][OAc] and [C(1)C(4)Im][TFA], respectively. By IR spectroscopy it was found that, when dissolved in the ILs, glycine was mainly present in its zwitterionic form. Structural and energetic aspects of the solvation of glycine in the ILs and in mixtures of ILs and water were investigated by ab initio calculations and molecular dynamic simulations. It was observed that the firstly solvation shell around glycine consisted predominantly of acetate or trifluoroacetate anions, which formed hydrogen bonds either with the carboxylic group of neutral glycine or with the protonated ammonium group of the zwitterionic form. When water is present in the solutions, hydrogen bonds between water and the anion prevail. The overall energy of the system was decomposed into its components between pairs of species. It was established that the dominant contribution to the interaction energy between glycine and the IL was due to hydrogen bonds with the anions and the statistics of hydrogen bonds were analysed. PMID:22434786

  5. Swelling and hydrolysis kinetics of Kraft pulp fibers in aqueous 1-butyl-3-methylimidazolium hydrogen sulfate solutions.

    PubMed

    Mao, Jia; Abushammala, Hatem; Pereira, Laura Barcellos; Laborie, Marie-Pierre

    2016-11-20

    1Butyl-3-methylimidazolium hydrogen sulfate ([Bmim]HSO4) is efficient at extracting cellulose nanocrystals from pulp fibers. To shed some light on the respective contributions of swelling and hydrolysis of pulp fibers by [Bmim]HSO4, the physical, structural and morphological characteristics of hardwood Kraft pulp fibers were monitored under various conditions of temperature, water content and time. Swelling was largely compounded by hydrolysis at the highest temperatures (120°C) as evidenced by mass loss and reduced degree of polymerization (DPn) at this temperature. At 120°C only, water content appeared to play a significant role on the extent of hydrolysis. At this temperature, a heterogeneous kinetic model involving weak links and amorphous regions best described the experimental data. Hydrolysis rates were maximum at 25% water content in the aqueous ionic liquid. PMID:27561498

  6. Anomalous Freezing of Nano-Confined Water in Room-Temperature Ionic Liquid 1-Butyl-3-Methylimidazolium Nitrate.

    PubMed

    Abe, Hiroshi; Takekiyo, Takahiro; Yoshimura, Yukihiro; Saihara, Koji; Shimizu, Akio

    2016-04-18

    Non-crystal formation of ice is investigated by simultaneous X-ray diffraction and differential scanning calorimetry measurements upon cooling to -100 °C. At room temperature, size-tunable water confinement (≈20 Å size) in a room-temperature ionic liquid (RTIL, 1-butyl-3-methylimidazolium nitrate, [C4 mim][NO3 ]) exists in a water-rich region (70-90 mol % D2 O). The confined water (water pocket) is characterized by almost monodispersive size distribution. In [C4 mim][NO3 ]-x mol % D2 O (70

  7. Polymer electrolyte based on crosslinked poly(glycidyl methacrylate) and 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide

    NASA Astrophysics Data System (ADS)

    Fei, Beatrice Wong Chui; Hanifah, Sharina Abu; Ahmad, Azizan; Hassan, Nur Hasyareeda

    2015-09-01

    Polymer electrolytes based on crosslinked poly(glycidyl methacrylate) as polymer host and 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (BmimTFSI) as incorporated salt were prepared by in-situ photopolymerization technique. The complexes with different mass ratio of glycidyl methacrylate (GMA) monomer to BmimTFSI were investigated. The ionic conductivity of the polymer electrolyte was increased and reach the highest value of 7.50 × 10-4 S cm-1 at the ratio of 3:7 (GMA: BmimTFSI). The interaction between the polymer host and ionic liquid was proved by Attenuated Total Reflectance-Fourier Transformation Infra-Red Spectroscopy (ATR-FTIR). Meanwhile, the X-ray diffraction analysis shows the amorphousity of the polymer electrolyte film increase with the ionic liquid ratio.

  8. Polymer electrolyte based on crosslinked poly(glycidyl methacrylate) and 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide

    SciTech Connect

    Fei, Beatrice Wong Chui; Hanifah, Sharina Abu; Ahmad, Azizan; Hassan, Nur Hasyareeda

    2015-09-25

    Polymer electrolytes based on crosslinked poly(glycidyl methacrylate) as polymer host and 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (BmimTFSI) as incorporated salt were prepared by in-situ photopolymerization technique. The complexes with different mass ratio of glycidyl methacrylate (GMA) monomer to BmimTFSI were investigated. The ionic conductivity of the polymer electrolyte was increased and reach the highest value of 7.50 × 10{sup −4} S cm{sup −1} at the ratio of 3:7 (GMA: BmimTFSI). The interaction between the polymer host and ionic liquid was proved by Attenuated Total Reflectance-Fourier Transformation Infra-Red Spectroscopy (ATR-FTIR). Meanwhile, the X-ray diffraction analysis shows the amorphousity of the polymer electrolyte film increase with the ionic liquid ratio.

  9. Comparison and Characterisation of Regenerated Chitosan from 1-Butyl-3-methylimidazolium Chloride and Chitosan from Crab Shells

    PubMed Central

    Arnold, Lyndon

    2015-01-01

    Chitosan is a biopolymer derived from chitin which is naturally occurring in the exoskeleton of crustaceans. This paper reports dissolution and regeneration of chitosan by directly dissolving in an ionic liquid solvent, 1-butyl-3-methylimidazolium chloride (BMIMCl). This will provide an ideal platform to solubilise these kinds of polymers to achieve the dissolution. The current study dissolved chitosan from crab shell utilising BMIMCl as a solvent and characterised the resultant regenerated polymer. The regenerated chitosan showed increased hydrogen bonding when characterised by Fourier transform infrared (FTIR) spectral analysis. In addition, the study also compared the characteristics of regenerated and generic chitosan. The regenerated chitosan was also evaluated for antimicrobial properties and showed to possess antibacterial features similar to the commercial grade. This method can be utilised in future for blending of polymers with chitosan in a dissolved phase. PMID:26090452

  10. New solvents designed on the basis of the molecular-microscopic properties of binary mixtures of the type (protic molecular solvent + 1-butyl-3-methylimidazolium-based ionic liquid).

    PubMed

    Fortunato, Graciela G; Mancini, Pedro M; Bravo, M Virginia; Adam, Claudia G

    2010-09-16

    The main purpose of this work is to analyze the microscopic feature of solvent systems resulting from the basis of binary mixtures formed by a protic molecular solvent (methanol, ethanol, propan-1-ol, propan-2-ol, and 2-ethoxyethanol) and a 1-butyl-3-methylimidazolium (bmim)-based ionic liquid (IL) cosolvent composed of different anions (tetrafluoroborate, hexafluorophosphate, chloride, and bromide). At the same time, a complementary aim is to evaluate the incidence of anion type on the solvation pattern. The empirical solvatochromic parameters E(T)(N), π*, β, and α were determined from the UV-vis solvatochromic shifts of adequate probes. The behavior of the solvent systems was analyzed according to their deviation from ideality. E(T)(N) polarity and π* dipolarity/polarizability exhibit positive deviation from ideal behavior in all binary mixtures at the explored compositions. Moreover, E(T)(N) and α parameters display synergetic effects in some binary mixtures composed of tetrafluoroborate and hexafluorophosphate anions. The influence of anion nature on the response patterns is clearly manifested in the basicity β and acidity α of the media. This is connected with the degree and type of interaction between the anions and the 1-butyl-3-methylimidazolium cation. The ion-pair character of the ionic liquids affects their interactions with a solute or a molecular solvent. The application of an appropriate preferential solvation model allowed us to obtain valuable information about solute-solvent and solvent-solvent interactions of the selected ionic liquid mixtures. It is possible to identify relevant mixtures paying particular attention to the most remarkable microscopic properties, the acidity and the basicity, in order to propose "new solvents". Thus, the solvating feature can be tailored selecting the molecular and/or the ionic component at a particular composition. A simplified combined nearly ideal binary solvent/Redlich-Kister (CNIBS/R-K) equation is

  11. Experimental and quantum study of corrosion of A36 mild steel towards 1-butyl-3-methylimidazolium tetrachloroferrate ionic liquid

    NASA Astrophysics Data System (ADS)

    Ullah, Sami; Bustam, Mohamad Azmi; Shariff, Azmi Mohamad; Gonfa, Girma; Izzat, Khairul

    2016-03-01

    The corrosion behaviour of ionic liquid 1-butyl-3-methylimidazolium tetrachloroferrate ([C4C1im][FeCl4]) towards A36 mild steel was studied through experiments and quantum calculations. The corrosion rates were obtained through immersion tests both in open and controlled environments. The surface morphology of the A36 mild steel was investigated using scanning electron microscopy (SEM). The effects of temperature and water content on the corrosion of the ionic liquid towards A36 mild steel were studied through electrochemical corrosion measurement techniques. The results show that the corrosion of [C4C1im][FeCl4] towards the mild steel in the open environment is 17 times higher than in the control environment. The corrosion rate increases with increasing temperature and water content in [C4C1im][FeCl4]. Density Functional Theory (DFT) calculations were performed to gain some insight into the interactions of [C4C1im][FeCl4] with the A36 mild steels surface.

  12. Molecular dynamics simulations of n-hexane at 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide interface

    SciTech Connect

    Lisal, Martin; Izak, Pavel

    2013-07-07

    Molecular dynamics simulations of n-hexane adsorbed onto the interface of 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide ([bmim][Tf{sub 2}N]) are performed at three n-hexane surface densities, ranged from 0.7 to 2.3 {mu}mol/m{sup 2} at 300 K. For [bmim][Tf{sub 2}N] room-temperature ionic liquid, we use a non-polarizable all-atom force field with the partial atomic charges based on ab initio calculations for the isolated ion pair. The net charges of the ions are {+-}0.89e, which mimics the anion to cation charge transfer and polarization effects. The OPLS-AA force field is employed for modeling of n-hexane. The surface tension is computed using the mechanical route and its value decreases with increase of the n-hexane surface density. The [bmim][Tf{sub 2}N]/n-hexane interface is analyzed using the intrinsic method, and the structural and dynamic properties of the interfacial, sub-interfacial, and central layers are computed. We determine the surface roughness, global and intrinsic density profiles, and orientation ordering of the molecules to describe the structure of the interface. We further compute the survival probability, normal and lateral self-diffusion coefficients, and re-orientation correlation functions to elucidate the effects of n-hexane on dynamics of the cations and anions in the layers.

  13. Synthesis, characterization and application of 1-butyl-3 methylimidazolium chloride as green material for extractive desulfurization of liquid fuel.

    PubMed

    Dharaskar, Swapnil A; Varma, Mahesh N; Shende, Diwakar Z; Yoo, Chang Kyoo; Wasewar, Kailas L

    2013-01-01

    The possible application of imidazolium ionic liquids as energy-efficient green material for extractive deep desulfurization of liquid fuel has been investigated. 1-Butyl-3-methylimidazolium chloride [BMIM]Cl was synthesized by nucleophilic substitution reaction of n-methylimidazolium and 1-chlorobutane. Molecular structures of the ILs were confirmed by FTIR, (1)H-NMR, and (13)C-NMR. The thermal properties, conductivity, solubility, water content and viscosity analysis of [BMIM]Cl were carried out. The effects of reaction time, reaction temperature, sulfur compounds, and recycling of IL without regeneration on dibenzothiophene removal of liquid fuel were presented. In the extractive desulfurization process, the removal of dibenzothiophene in n-dodecane using [BMIM]Cl was 81% with mass ratio of 1 : 1, in 30 min at 30°C under the mild reaction conditions. Also, desulfurization of real fuels with IL and multistage extraction were studied. The results of this work might offer significant insights in the perceptive use of imidazoled ILs as energy-efficient green material for extractive deep desulfurization of liquid fuels as it can be reused without regeneration with considerable extraction efficiency. PMID:24307868

  14. The genotoxic and cytotoxic effects of 1-butyl-3-methylimidazolium chloride in soil on Vicia faba seedlings.

    PubMed

    Liu, Tong; Zhu, Lusheng; Wang, Jinhua; Wang, Jun; Xie, Hui

    2015-03-21

    Although considered as "green" solvents, the toxic effects of ionic liquids (ILs) on organisms have been widely investigated in recent years. However, studies on the toxic effects of ILs on plants all focus on toxicity in nutrient solution. In the present paper, the toxic effects of 1-butyl-3-methylimidazolium chloride ([C4mim]Cl) on Vicia faba seedlings in soil at 0, 500, 1500, and 2500 mg kg(-1) on day 10 were studied. The present results showed that the growth of V. faba seedlings may be seriously inhibited when the IL concentrations were higher than 500 mg kg(-1). The EC50 values for shoot length, root length, and dry weight were 3886, 2483, and 3359 mg kg(-1), respectively. In addition, [C4mim]Cl caused lipid peroxidation and DNA damage at 500 mg kg(-1) and oxidative stress at 1500 mg kg(-1), which indicated that [C4mim]Cl may have genotoxicity and cytotoxicity on V. faba seedlings. Moreover, oxidative damage may be the main toxic mechanism of ILs. PMID:25462868

  15. Synthesis, Characterization and Application of 1-Butyl-3 Methylimidazolium Chloride as Green Material for Extractive Desulfurization of Liquid Fuel

    PubMed Central

    Dharaskar, Swapnil A.; Varma, Mahesh N.; Shende, Diwakar Z.; Yoo, Chang Kyoo; Wasewar, Kailas L.

    2013-01-01

    The possible application of imidazolium ionic liquids as energy-efficient green material for extractive deep desulfurization of liquid fuel has been investigated. 1-Butyl-3-methylimidazolium chloride [BMIM]Cl was synthesized by nucleophilic substitution reaction of n-methylimidazolium and 1-chlorobutane. Molecular structures of the ILs were confirmed by FTIR, 1H-NMR, and 13C-NMR. The thermal properties, conductivity, solubility, water content and viscosity analysis of [BMIM]Cl were carried out. The effects of reaction time, reaction temperature, sulfur compounds, and recycling of IL without regeneration on dibenzothiophene removal of liquid fuel were presented. In the extractive desulfurization process, the removal of dibenzothiophene in n-dodecane using [BMIM]Cl was 81% with mass ratio of 1 : 1, in 30 min at 30°C under the mild reaction conditions. Also, desulfurization of real fuels with IL and multistage extraction were studied. The results of this work might offer significant insights in the perceptive use of imidazoled ILs as energy-efficient green material for extractive deep desulfurization of liquid fuels as it can be reused without regeneration with considerable extraction efficiency. PMID:24307868

  16. Role of solubilized water in micelles formed by Triton X-100 in 1-butyl-3-methylimidazolium ionic liquids.

    PubMed

    Li, Na; Zhang, Shaohua; Ma, Hongchao; Zheng, Liqiang

    2010-06-15

    We demonstrate here the aggregation behavior of a nonionic surfactant Triton X-100 in two 1-butyl-3-methylimidazolium ionic liquids (the hydrophilic IL [bmim][BF(4)] and the hydrophobic IL [bmim][PF(6)]) by surface tension measurements. The effects of added water on the microstructure of Triton X-100 in ILs micelles are investigated. When small amounts of water are added to Triton X-100 in [bmim][PF(6)] micelles, the water molecules are first bound to the ethylene oxide (EO) units of Triton X-100 and then form the water pool in the core of the microemulsion. When water molecules are added to the Triton X-100 in [bmim][BF(4)] micelles, there is no microemulsion formed; these water molecules are first solubilized in [bmim][BF(4)]. When the solubilization is saturated, the water molecules start to bind to the EO group of Triton X-100; these results are confirmed by UV-vis, FTIR, and (1)H NMR spectra. PMID:20302278

  17. Structural studies of 1-butyl-3-methylimidazolium tetrafluoroborate/TX-100/ p-xylene ionic liquid microemulsions.

    PubMed

    Gao, Yan'an; Zhang, Jin; Xu, Hongyan; Zhao, Xueyan; Zheng, Liqiang; Li, Xinwei; Yu, Li

    2006-07-17

    The ionic liquid (IL) 1-butyl-3-methylimidazolium tetrafluoroborate (bmimBF4) forms nonaqueous microemulsions with p-xylene, with the aid of the nonionic surfactant TX-100. The phase behavior of the ternary system is investigated, and three microregions of the microemulsions-ionic liquid-in-oil (IL/O), bicontinuous, and oil-in-ionic liquid (O/IL)-are identified by conductivity measurements, according to percolation theory. On the basis of a phase diagram, a series of IL/O microemulsions are chosen and characterized by dynamic light scattering (DLS). The size of aggregates increases on increasing the amount of added polar component (bmimBF(4)), which is a similar phenomenon to that observed for typical water-in-oil (W/O) microemulsions, suggesting the formation of IL/O microemulsions. The microstructural characteristics of the microemulsions are investigated by FTIR and 1H NMR spectroscopy. The results indicate that the interaction between the electronegative oxygen atoms of the oxyethylene (OE) units in TX-100 and the electropositive imidazolium ring may be the driving force for the solubilization of bmimBF4 into the core of the TX-100 aggregates. In addition, the micropolarity of the microemulsions is investigated by using methyl orange (MO) as a UV/Vis spectroscopic probe. A relatively constant polarity of the microemulsion droplets is obtained in the IL microemulsion. Finally, a plausible structure for the IL/O microemulsion is presented. PMID:16789041

  18. The effect of water on the microstructure of 1-butyl-3-methylimidazolium tetrafluoroborate/TX-100/benzene ionic liquid microemulsions.

    PubMed

    Gao, Yan'an; Li, Na; Zheng, Liqiang; Zhao, Xueyan; Zhang, Jin; Cao, Quan; Zhao, Mingwei; Li, Zhen; Zhang, Gaoyong

    2007-01-01

    The ionic liquid (IL) 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF4]) forms nonaqueous microemulsions with benzene with the aid of nonionic surfactant TX-100. The phase diagram of the ternary system was prepared, and the microstructures of the microemulsion were recognized. On the basis of the phase diagram, a series of ionic liquid-in-oil (IL/O) microemulsions were chosen and characterized by dynamic light scattering (DLS), which shows a similar swelling behavior to typical water-in-oil (W/O) microemulsions. The existence of IL pools in the IL/O microemulsion was confirmed by UV/Vis spectroscopic analysis with CoCl2 and methylene blue (MB) as the absorption probes. A constant polarity of the IL pool is observed, even if small amounts of water are added to the microemulsion, thus suggesting that the water molecules are solubilized in the polar outer shell of the microemulsion, as confirmed by FTIR spectra. 1H NMR spectroscopic analysis shows that these water molecules interact with the electronegative oxygen atoms of the oxyethylene (OE) units of TX-100 through hydrogen-bonding interactions, and the electronegative oxygen atoms of the water molecules attract the electropositive imidazolium rings of [bmim][BF4]. Hence, the water molecules are like a glue that stick the IL and OE units more tightly together and thus make the microemulsion system more stable. Considering the unique solubilization behavior of added water molecules, the IL/O microemulsion system may be used as a medium to prepare porous or hollow nanomaterials by hydrolysis reactions. PMID:17177215

  19. Role of solubilized water in the reverse ionic liquid microemulsion of 1-butyl-3-methylimidazolium tetrafluoroborate/TX-100/benzene.

    PubMed

    Gao, Yan'an; Li, Na; Zheng, Liqiang; Bai, Xiangtao; Yu, Li; Zhao, Xueyan; Zhang, Jin; Zhao, Mingwei; Li, Zhen

    2007-03-15

    The ionic liquid (IL) 1-butyl-3-methylimidazolium tetrafluoroborate (bmimBF4) can form nonaqueous microemulsions with benzene by the aid of nonionic surfactant TX-100. The effect of water on ionic liquid-in-oil (IL/O) microemulsions was studied, and it was shown that the addition of small amount of water to the IL microemulsion contributed to the stability of microemulsion and thus increased the amount of solubilized bmimBF4 in the microemulsion. The conductivity measurements also showed that the attractive interactions between IL microdroplets were weakened, that is, the IL/O microemulsion becomes more stable in the present of some water. Fourier transform IR was carried out to analyze the states of the added water, and the result showed that these water molecules mainly behaved as bound water and trapped water, indicating that the water molecules are located in the palisade layers of the IL/O microemulsion. Furthermore, 1H NMR and 19F NMR spectra suggested that the added water molecules built the hydrogen binding network of imidazolium cations and H2O, BF4- anion and H2O, and at the same time the electronegative oxygen atoms of the oxyethylene units of TX-100 and water in the palisade layers, which made the palisade layers more firm and thus increased the stability of the microemulsion. The study can help in further understanding the formation mechanism of microemulsions. In addition, the characteristic solubilization behavior of the added water can provide an aqueous interface film for hydrolysis reactions and therefore may be used as an ideal medium to prepare porous or hollow nanomaterials. PMID:17305388

  20. Solvent and rotational relaxation of Coumarin-153 in a micellar solution of a room-temperature ionic liquid, 1-butyl-3-methylimidazolium octyl sulfate, in ethylammonium nitrate

    NASA Astrophysics Data System (ADS)

    Rao, Vishal Govind; Ghatak, Chiranjib; Pramanik, Rajib; Sarkar, Souravi; Sarkar, Nilmoni

    2010-10-01

    We have investigated the micelle formation by room-temperature ionic liquid (RTIL), 1-butyl-3-methylimidazolium octyl sulfate (bmimOs) with another RTIL, ethyl ammonium nitrate (EAN). In addition, the effect of micelle formation on the solvation and rotational relaxation dynamics have been observed using steady-state and picoseconds time-resolved spectroscopy. Both the solvent and rotational relaxations of Coumarin-153 are retarded in the micelle compared to that of neat EAN. The increase in average solvation time on going from neat EAN to bmimOs-EAN micelle is very small compared to the increase in solvation time on going from pure water to water containing micelle.

  1. Experimental and theoretical investigation of multistage extraction of 1,3-propanediol using the extraction system phosphate/1-butyl-3-methylimidazolium trifluoromethanesulfonate/water.

    PubMed

    Müller, Anja; Lutze, Philip; Górak, Andrzej

    2013-01-01

    The separation of 1,3-propanediol from fermentation broth is a challenging and energy-demanding step using conventional unit operations. One alternative process is the use of an aqueous two-phase system incorporating ionic liquids to use synergy effects of both technologies. Within this manuscript, the technical feasibility of the extraction of 1,3-propanediol using the aqueous two-phase system phosphate (salt)/1-butyl-3-methylimidazolium trifluoromethanesulfonate (ionic liquid)/water in a continuously operated process in pilot-scale is presented. The extraction was performed in a multistage mixer-settler unit and successfully modeled with an equilibrium-stage model and correlations to describe the liquid-liquid equilibrium of the salt/ionic liquid/water two-phase system. The developed and validated model was used for a further investigation of the influence of different process parameters in the determined operating window. Theses parameters include the number of stages, the phase ratio, the pH, and the mass fraction of the involved components. The results prove that the phosphate and 1-butyl-3-methylimidazolium trifluoromethanesulfonate mass fraction, the phase ratio, and the number of stages have a considerable influence on the recovery of 1,3-propanediol, whereas the pH value has only a smaller impact. Those results can be used for optimization of the system as well as for targeting future research within this area. PMID:23554391

  2. States of water located in the continuous organic phase of 1-butyl-3-methylimidazolium tetrafluoroborate/Triton X-100/triethylamine reverse microemulsions.

    PubMed

    Li, Na; Cao, Quan; Gao, Yanan; Zhang, Jin; Zheng, Liqiang; Bai, Xiangtao; Dong, Bin; Li, Zhen; Zhao, Mingwei; Yu, Li

    2007-10-22

    We demonstrate a novel ionic liquid (IL) microemulsion, consisting of 1-butyl-3-methylimidazolium tetrafluoroborate (bmimBF4) and nonionic surfactant Triton X-100 prepared in triethylamine which is used either as an organic solvent or a Lewis base. The effects of small amounts of added water on the microstructure of the IL microemulsion are investigated by various techniques. UV/Vis spectroscopic analysis and FTIR spectra indicate that these water molecules are not solubilized into the IL pools of the microemulsions. 1H NMR spectra further show that the added water binds with triethylamine to form a surrounding OH- base environment. Some of OH- ions enter the palisade layers of the IL microemulsions and a continuous base interface is created. The unique solubilization behavior of water reveals that it is possible to use the triethylamine microemulsions as a template to prepare metal hydroxides as well as metal oxides in the microemulsions, which is not possible when using traditional microemulsions. PMID:17886245

  3. Physical Properties of Ionic Liquids Consisting of the 1-Butyl-3-Methylimidazolium Cation with Various Anions and the Bis(trifluoromethylsulfonyl)imide Anion with Various Cations

    SciTech Connect

    Jin, Hui; O'Hare, Bernie; Dong, Jing; Arzhantsev, Sergei; Baker, Gary A; Wishart, James F.; Benesi, Alan; Maroncelli, Mark

    2008-01-01

    Physical properties of 4 room-temperature ionic liquids consisting of the 1-butyl-3-methylimidazolium cation with various perfluorinated anions and the bis(trifluoromethylsulfonyl)imide (Tf2N-) anion with 12 pyrrolidinium-, ammonium-, and hydroxyl-containing cations are reported. Electronic structure methods are used to calculate properties related to the size, shape, and dipole moment of individual ions. Experimental measurements of phase-transition temperatures, densities, refractive indices, surface tensions, solvatochromic polarities based on absorption of Nile Red, 19F chemical shifts of the Tf2N- anion, temperature-dependent viscosities, conductivities, and cation diffusion coefficients are reported. Correlations among the measured quantities as well as the use of surface tension and molar volume for estimating Hildebrand solubility parameters of ionic liquids are also discussed.

  4. Effect of 1-Butyl-3-methylimidazolium Halide on the Relative Stability between Sodium Dodecyl Sulfate Micelles and Sodium Dodecyl Sulfate-Poly(ethylene oxide) Nanoaggregates.

    PubMed

    Ferreira, Gabriel M Dias; Ferreira, Guilherme M Dias; Agudelo, Álvaro J Patiño; Hespanhol da Silva, Maria C; Rezende, Jaqueline de Paula; Pires, Ana Clarissa Dos Santos; da Silva, Luis Henrique Mendes

    2015-12-24

    It is well-known that ionic liquids (ILs) alter the properties of aqueous systems containing only surfactants. However, the effect of ILs on polymer-surfactant systems is still unknown. Here, the effect of 1-butyl-3-methylimidazolium bromide (bmimBr) and chloride (bmimCl) on the micellization of sodium dodecyl sulfate (SDS) and its interaction with poly(ethylene oxide) (PEO) was evaluated using conductimetry, fluorimetry, and isothermal titration calorimetry. The ILs decreased the critical micellar concentration (cmc) of the surfactant, stabilizing the SDS micelles. A second critical concentration (c2thc) was verified at high SDS concentrations, due to the micelle size decrease. The stability of PEO/SDS aggregates was also affected by ILs, and the critical aggregation concentration (cac) of SDS increased. Integral aggregation enthalpy changed from -0.72 in water to 2.16 kJ mol(-1) in 4.00 mM bmimBr. IL anions did not affect the SDS micellization or the beginning of PEO/SDS aggregation. Nevertheless, when chloride was replaced with bromide, the amount of SDS bound to the polymer increased. At 100.0 mM IL, the PEO-SDS interaction vanished. We suggest that the effect of ILs comes from participating in the structure of the formed aggregates, interacting with the SDS monomers at the core/interface of the micelles, and promoting preferential solvation of the polymer. PMID:26595360

  5. Decrease of droplet size of the reverse microemulsion 1-butyl-3-methylimidazolium tetrafluoroborate/Triton X-100/cyclohexane by addition of water.

    PubMed

    Gao, Yanan; Hilfert, Liane; Voigt, Andreas; Sundmacher, Kai

    2008-03-27

    In the present contribution, results concerning the role of small amounts of water in the 1-butyl-3-methylimidazolium tetrafluoroborate (bmimBF4)-in-cyclohexane ionic liquid (IL) reverse microemulsions are reported. Dynamic light scattering (DLS) revealed that the size of microemulsion droplets decreased remarkably with increasing water content although water is often used as a polar component to swell reverse microemulsions. It was thus deduced that the number of microemulsion droplets was increased which was confirmed by conductivity measurements. The states of dissolved water were investigated by Fourier transform IR (FTIR) spectroscopic analysis showing that water molecules mainly act as bound water. 1H NMR along with two-dimensional rotating frame nuclear Overhauser effect (NOE) experiments (ROESY) further revealed that water molecules were mainly located in the periphery of the polar core of the microemulsion droplets and behave like a chock being inserted in the palisade layer of the droplet. This increased the curvature of the surfactant film at the IL/cyclohexane interface and thus led to the decrease of the microemulsion droplet size. The order of surfactant molecules arranged in the interface film was increased and thus induced a loss of entropy. Isothermal titration calorimetry (ITC) indicated that an enthalpy increase compensates for the loss of entropy during the process of microstructural transition. PMID:18318531

  6. Electrochemical and Thermodynamic Properties of Ln(III) (Ln = Eu, Sm, Dy, Nd) in 1-Butyl-3-Methylimidazolium Bromide Ionic Liquid

    PubMed Central

    Yang, Xiao; He, Ling; Qin, Song; Tao, Guo-Hong; Huang, Ming; Lv, Yi

    2014-01-01

    The electrochemical behavior and thermodynamic properties of Ln(III) (Ln = Eu, Sm, Dy, Nd) were studied in 1-butyl-3-methylimidazolium bromide ionic liquid (BmimBr) at a glassy carbon (GC) electrode in the range of 293–338 K. The electrode reaction of Eu(III) was found to be quasi-reversible by the cyclic voltammetry, the reactions of the other three lanthanide ions were regarded as irreversible systems. An increase of the current intensity was obtained with the temperature increase. At 293 K, the cathodic peak potentials of −0.893 V (Eu(III)), −0.596 V (Sm(III)), −0.637 V (Dy(III)) and −0.641 V (Nd(III)) were found, respectively, to be assigned to the reduction of Ln(III) to Ln(II). The diffusion coefficients (Do), the transfer coefficients (α) of Ln(III) (Ln = Eu, Sm, Dy, Nd) and the charge transfer rate constants (ks) of Eu(III) were estimated. The apparent standard potential (E0*) and the thermodynamic properties of the reduction of Eu(III) to Eu(II) were also investigated. PMID:24752584

  7. Thermodynamic, dynamic, and structural properties of ionic liquids comprised of 1-butyl-3-methylimidazolium cation and nitrate, azide, or dicyanamide anions.

    PubMed

    Bedrov, Dmitry; Borodin, Oleg

    2010-10-14

    Molecular dynamics simulations of ionic liquids (IL) comprised of 1-butyl-3-methylimidazolium [bmim] cation and nitrate [NO(3)], azide [N(3)], or dicyanamide [N(CN)(2)] anions were conducted using the polarizable APPLE&P force field. Comparison of thermodynamic properties such as densities, enthalpies of vaporization, and ion binding energies as well as structural correlations obtained from simulations at atmospheric pressure and temperature range 298-393 K showed that IL with the N(CN)(2) anion shows significantly different characteristics as compared to ILs with the N(3) and NO(3) anions. [bmim][N(CN)(2)] IL was found to have the lowest enthalpy of vaporization and the weakest ion-ion structural correlation as compared to ILs with the other two ions. This trend was further manifested in dynamical properties characterized by self-diffusion coefficients and molecular rotational relaxation times, where IL with the N(CN)(2) anion showed the fastest dynamics as compared to other ILs. We also examine the dynamic correlations between the ions' translational and rotational motions as well as discuss the anisotropy of the latter. PMID:20849137

  8. Liberation of fermentable sugars from soybean hull biomass using ionic liquid 1-butyl-3-methylimidazolium acetate and their bioconversion to ethanol.

    PubMed

    da Cunha-Pereira, Fernanda; Rech, Rosane; Záchia Ayub, Marco Antônio; Pinheiro Dillon, Aldo; Dupont, Jairton

    2016-03-01

    Optimized hydrolysis of lignocellulosic waste biomass is essential to achieve the liberation of sugars to be used in fermentation process. Ionic liquids (ILs), a new class of solvents, have been tested in the pretreatment of cellulosic materials to improve the subsequent enzymatic hydrolysis of the biomass. Optimized application of ILs on biomass is important to advance the use of this technology. In this research, we investigated the effects of using 1-butyl-3-methylimidazolium acetate ([bmim][Ac]) on the decomposition of soybean hull, an abundant cellulosic industrial waste. Reaction aspects of temperature, incubation time, IL concentration, and solid load were optimized before carrying out the enzymatic hydrolysis of this residue to liberate fermentable glucose. Optimal conditions were found to be 75°C, 165 min incubation time, 57% (mass fraction) of [bmim][Ac], and 12.5% solid loading. Pretreated soybean hull lost its crystallinity, which eased enzymatic hydrolysis, confirmed by Fourier Transform Infrared analysis. The enzymatic hydrolysis of the biomass using an enzyme complex from Penicillium echinulatum liberated 92% of glucose from the cellulose matrix. The hydrolysate was free of any toxic compounds, such as hydroxymethylfurfural and furfural. The obtained hydrolysate was tested for fermentation using Candida shehatae HM 52.2, which was able to convert glucose to ethanol at yields of 0.31. These results suggest the possible use of ILs for the pretreatment of some lignocellulosic waste materials, avoiding the formation of toxic compounds, to be used in second-generation ethanol production and other fermentation processes. © 2015 American Institute of Chemical Engineers Biotechnol. Prog., 32:312-320, 2016. PMID:26588200

  9. Temperature-programed time-of-flight secondary ion mass spectrometry study of 1-butyl-3-methylimidazolium trifluoromethanesulfonate during glass-liquid transition, crystallization, melting, and solvation

    SciTech Connect

    Souda, Ryutaro; Guenster, Jens

    2008-09-07

    For this study, time-of-flight secondary ion mass spectrometry was used to analyze the molecular orientation of 1-butyl-3-methylimidazolium trifluoromethanesulfonate ([bmim][OTf]) and its interaction with the adsorbed Na and LiI species at temperatures of 150-300 K. A glassy [bmim][OTf] film crystallizes at around 230 K, as observed from the increase in the [bmim]{sup +} yield. LiI and Na adsorbed on the glassy film are solvated, whereas they tend to form islands on a crystalline film. The crystalline surface inertness is ascribable to the termination with the CF{sub 3} and C{sub 4}H{sub 9} groups, whereas the exposure of polar SO{sub 3} and imidazole groups at the glassy film results in the solvation. Surface layering occurs during solvation of LiI on the glassy film in such a way that the [bmim]{sup +} ([OTf]{sup -}) moiety is exposed to the vacuum (oriented to the bulk). The LiI adsorbed on the glassy film is incorporated into the bulk at temperatures higher than 200 K because of the glass-liquid transition. No further uptake of LiI is observed during crystallization, providing a contrast to the results of normal molecular solids such as water and ethanol. The surface layers of the crystal melt at temperatures below the bulk melting point, as confirmed from the dissolution of adsorbed LiI, but the melting layer retains a short-range order similar to the crystal. The [bmim][OTf] can be regarded as a strongly correlated liquid with the combined liquid property and crystal-type local structure. The origin of this behavior is discussed.

  10. Aerosol-OT in water forms fully-branched cylindrical direct micelles in the presence of the ionic liquid 1-butyl-3-methylimidazolium bromide.

    PubMed

    Murgia, Sergio; Palazzo, Gerardo; Mamusa, Marianna; Lampis, Sandrina; Monduzzi, Maura

    2011-05-28

    A recent investigation on the sodium bis(2-ethylhexyl)sulfosuccinate/water/1-butyl-3-methylimidazolium tetrafluoborate (NaAOT/W/bmimBF(4)) system showed that the anionic two-tailed surfactant NaAOT, that is known to form reverse micelles or planar interfaces (typically lamellar liquid crystals), can originate discrete spherical micelles of normal curvature because of strong interactions with the ionic liquid. The goal of the present paper was to detect macro- and microscopic modifications within such a system upon substitution of the ionic liquid's counter-ion tetrafluoroborate with bromide. Firstly, the phase diagram of the NaAOT/water/bmimBr system was determined. Then, the monophasic regions were investigated by means of NMR self-diffusion and SAXRD experiments. The results obtained proved this system to be surprisingly different from that containing bmimBF(4). This study focused mainly on the characterization of the micellar region, which turned out to be constituted of a bicontinuous nanostructure. This finding can be accounted for suggesting a decreasing of the NaAOT effective surfactant packing parameter, as in the case of NaAOT/water/bmimBF(4) system, although the effect in the presence of Br(-) is less pronounced. Data modeling showed the same degree of interfacial adsorption for the bmim(+) cation in both systems, regardless of the particular counterion used-either BF(4)(-) or Br(-). Thus, the remarkable differences between the two systems appear to be mainly due to a specific counterion effect. This result highlights once again the ions specificity, which is found ubiquitously in chemistry and biology. PMID:21468445

  11. Electrochemical reduction of aromatic ketones in 1-butyl-3-methylimidazolium-based ionic liquids in the presence of carbon dioxide: the influence of the ketone substituent and the ionic liquid anion on bulk electrolysis product distribution.

    PubMed

    Zhao, Shu-Feng; Horne, Mike; Bond, Alan M; Zhang, Jie

    2015-07-15

    Electrochemical reduction of aromatic ketones, including acetophenone, benzophenone and 4-phenylbenzophenone, has been undertaken in 1-butyl-3-methylimidazolium-based ionic liquids containing tetrafluoroborate ([BF4](-)), trifluoromethanesulfonate ([TfO](-)) and tris(pentafluoroethyl)trifluorophosphate ([FAP](-)) anions in the presence of carbon dioxide in order to investigate the ketone substituent effect and the influence of the acidic proton on the imidazolium cation (C2-H) on bulk electrolysis product distribution. For acetophenone, the minor products were dimers (<10%) in all ionic liquids, which are the result of acetophenone radical anion coupling. For benzophenone and 4-phenylbenzophenone, no dimers were formed due to steric hindrance. In these cases, even though carboxylic acids were obtained, the main products generated were alcohols (>50%) derived from proton coupled electron transfer reactions involving the electrogenerated radical anions and C2-H. In the cases of both acetophenone and benzophenone, the product distribution is essentially independent of the ionic liquid anion. By contrast, 4-phenylbenzophenone shows a product distribution that is dependent on the ionic liquid anion. Higher yields of carboxylic acids (∼40%) are obtained with [TfO](-) and [FAP](-) anions because in these ionic liquids the C2-H is less acidic, making the formation of alcohol less favourable. In comparison with benzophenone, a higher yield of carboxylic acid (>30% versus ∼15%) was obtained with 4-phenylbenzophenone in all ionic liquids due to the weaker basicity of 4-phenylbenzophenone radical anion. PMID:26136079

  12. Partitioning of amino acids in the aqueous biphasic system containing the water-miscible ionic liquid 1-butyl-3-methylimidazolium bromide and the water-structuring salt potassium citrate.

    PubMed

    Zafarani-Moattar, Mohammed Taghi; Hamzehzadeh, Sholeh

    2011-07-01

    In biotechnology, extraction by means of aqueous biphasic systems (ABS) is known as a promising tool for the recovery and purification of bio-molecules. Over the past decade, the increasing emphasis on cleaner and environmentally benign extraction procedures has led to enhanced interest in the ABS containing ionic liquids (ILs)-a new class of non-volatile alternative solvents. ABS composed of the hydrophilic IL {1-butyl-3-methylimidazolium bromide ([C4 mim]Br)} and potassium citrate-which is easily degraded-represents a clean media to green separation of bio-molecules. In this regard, here, the extraction capability of this ABS was evaluated through its application to the extraction of some amino acids. To gain an insight into the driving forces of amino acid partitioning in the studied IL-based ABS, the distribution of five model amino acids (L-tryptophan, L-phenylalanine, L-tyrosine, L-leucine, and L-valine) at different aqueous medium pH values and different phase compositions was investigated. The studies indicated that hydrophobic interactions were the main driving force, although electrostatic interactions and salting-out effects were also important for the transfer of the amino acids. Moreover, based on the statistical analysis of the driving forces of amino acid partitioning in the studied IL-based ABS, a model was established to describe the partition coefficient of three model amino acids, L-tryptophan, L-phenylalanine, and L-valine, and employed to predict the partition coefficient of two other model amino acids, L-tyrosine and L-leucine. PMID:21509956

  13. Solvent and rotational relaxation of coumarin-153 and coumarin-480 in ionic liquid (1-butyl-3-methylimidazolium tetrafluoroborate) modified sodium 1,4-bis(2-ethylhexyl) sulfosuccinate (NaAOT) micelle

    NASA Astrophysics Data System (ADS)

    Rao, Vishal Govind; Banerjee, Chiranjib; Mandal, Sarthak; Ghosh, Surajit; Sarkar, Nilmoni

    2013-02-01

    Understanding ion transport dynamics, structure of surfactant aggregates in ionic liquids or ionic liquid/water solutions are quite interesting and potentially important due to widespread applications of surfactant-based systems. In this manuscript we have investigated the effect of 1-butyl-3-methylimidazolium tetrafluoroborate (bmimBF4) addition on solvent and rotational relaxation of coumarin-153 (C-153) and coumarin-480 (C-480) in aqueous solution of sodium 1,4-bis(2-ethylhexyl) sulfosuccinate (NaAOT) using steady state and picosecond time resolved fluorescence spectroscopy. The strong adsorption of the bmim+ at the interface and the role of the ionic liquid particularly the cation bmim+ in the modification of the interfacial geometry were probed by the analysis of decay parameters and the rotational relaxation parameters. Since the addition of the NaAOT in water-bmimBF4 mixture above critical micellar concentration (48 mM, obtained from observing pyrene fluorescence) causes strong adsorption of the ionic liquid particularly the cation bmim+, the average solvation time, particularly the slow component increases significantly. More importantly we have found the probe dependent solvation dynamics due to the different location of the probe molecules, C-153 and C-480. C-153 being hydrophobic in nature resides in the stern layer and the adsorption of the bmim+ at the interface modifies stern layer more effectively. So we have observed more pronounced change in solvation dynamics in case of C-153 compared to that in case of C-480. The fluorescence anisotropy decays of the probe molecules were found to be biexponential in nature. The anisotropy decay was interpreted by using a model which consists of the wobbling (rotational) and translational diffusion of the dye coupled with the rotational motion of the micelle as a whole.

  14. Solvent and rotational relaxation of coumarin-153 and coumarin-480 in ionic liquid (1-butyl-3-methylimidazolium tetrafluoroborate) modified sodium 1,4-bis(2-ethylhexyl) sulfosuccinate (NaAOT) micelle.

    PubMed

    Rao, Vishal Govind; Banerjee, Chiranjib; Mandal, Sarthak; Ghosh, Surajit; Sarkar, Nilmoni

    2013-02-01

    Understanding ion transport dynamics, structure of surfactant aggregates in ionic liquids or ionic liquid/water solutions are quite interesting and potentially important due to widespread applications of surfactant-based systems. In this manuscript we have investigated the effect of 1-butyl-3-methylimidazolium tetrafluoroborate (bmimBF(4)) addition on solvent and rotational relaxation of coumarin-153 (C-153) and coumarin-480 (C-480) in aqueous solution of sodium 1,4-bis(2-ethylhexyl) sulfosuccinate (NaAOT) using steady state and picosecond time resolved fluorescence spectroscopy. The strong adsorption of the bmim(+) at the interface and the role of the ionic liquid particularly the cation bmim(+) in the modification of the interfacial geometry were probed by the analysis of decay parameters and the rotational relaxation parameters. Since the addition of the NaAOT in water-bmimBF(4) mixture above critical micellar concentration (48 mM, obtained from observing pyrene fluorescence) causes strong adsorption of the ionic liquid particularly the cation bmim(+), the average solvation time, particularly the slow component increases significantly. More importantly we have found the probe dependent solvation dynamics due to the different location of the probe molecules, C-153 and C-480. C-153 being hydrophobic in nature resides in the stern layer and the adsorption of the bmim(+) at the interface modifies stern layer more effectively. So we have observed more pronounced change in solvation dynamics in case of C-153 compared to that in case of C-480. The fluorescence anisotropy decays of the probe molecules were found to be biexponential in nature. The anisotropy decay was interpreted by using a model which consists of the wobbling (rotational) and translational diffusion of the dye coupled with the rotational motion of the micelle as a whole. PMID:23220680

  15. Synthesis and characterization of hybrid materials based on 1-butyl-3-methylimidazolium tetrafluoroborate ionic liquid and Dawson-type tungstophosphate K{sub 7}[H{sub 4}PW{sub 18}O{sub 62}].18H{sub 2}O and K{sub 6}[P{sub 2}W{sub 18}O{sub 62}].13H{sub 2}O

    SciTech Connect

    Ammam, Malika; Fransaer, Jan

    2011-04-15

    In this study, we synthesized hybrid materials using well-Dawson polyoxometalates (POMs), K{sub 7}[H{sub 4}PW{sub 18}O{sub 62}].18H{sub 2}O or K{sub 6}[P{sub 2}W{sub 18}O{sub 62}].13H{sub 2}O and a room temperature ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM][BF{sub 4}]). K, W, P and CHN elemental analysis showed that one mole of [H{sub 4}PW{sub 18}O{sub 62}]{sup 7-} reacts with 6 moles of BMIM{sup +} and one mole of [P{sub 2}W{sub 18}O{sub 62}]{sup 6-} reacts with 4 moles of BMIM{sup +} to form, respectively, K[BMIM]{sub 6}H{sub 4}PW{sub 18}O{sub 62} and K{sub 2}[BMIM]{sub 4}P{sub 2}W{sub 18}O{sub 62}. X-ray diffraction illustrated amorphous structure of the hybrid materials. FT-IR spectra showed the presence of both 1-butyl-3-methylimidazolium cation and the Dawson anion. TG analysis displayed a relative thermal stability of the hybrid materials compared to the parents Dawson POMs. Cyclic voltammetry showed that the reduction peak potentials of the Dawson anion in the hybrid materials shift towards negative values and the shift is more pronounced for K[BMIM]{sub 6}H{sub 4}PW{sub 18}O{sub 62} compared to K{sub 2}[BMIM]{sub 4}P{sub 2}W{sub 18}O{sub 62}. This was attributed to a decrease in the acidity of the Dawson POM anion in the hybrid material. -- Graphical abstract: Powder XRD patterns of (a) PW{sub 18}, (b) K[BMIM]{sub 6}H{sub 4}PW{sub 18}O{sub 62}, (c) P{sub 2}W{sub 18}, and (d) K{sub 2}[BMIM]{sub 4}P{sub 2}W{sub 18}O{sub 62}. Display Omitted Research highlights: {yields} 1-butyl-3-methylimidazolium tetrafluoroborate([BMIM][BF{sub 4}]) reacts with K{sub 7}[H{sub 4}PW{sub 18}O{sub 62}].18H{sub 2}O to form K[BMIM]{sub 6}H{sub 4}PW{sub 18}O{sub 62}. {yields} [BMIM][BF{sub 4}] reacts with K{sub 6}[P{sub 2}W{sub 18}O{sub 62}].13H{sub 2}O to form K{sub 2}[BMIM]{sub 4}P{sub 2}W{sub 18}O{sub 62}. {yields} K[BMIM]{sub 6}H{sub 4}PW{sub 18}O{sub 62} and K{sub 2}[BMIM]{sub 4}P{sub 2}W{sub 18}O{sub 62} displayed amorphous structures. {yields} K

  16. ALPHA-AMYLASE ACTIVITY IN VARIOUS CONCENTRATIONS OF THE IONIC LIQUID, 1-BUTYL-3-METHYLIMIDAZOLIUM CHLORIDE

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Starch is an extremely abundant, economical and versatile industrial commodity. Many industrial uses of starch depend on hydrolyzing the polymer for the conversion of glucose and maltodextrins. Starch hydrolysis is frequently achieved by utilizing alpha-amylase, which is an endo-acting enzyme that...

  17. Distribution of 1-Butyl-3-methylimidazolium Bistrifluoromethylsulfonimide in Mesoporous Silica as a Function of Pore Filling

    SciTech Connect

    Han, Kee Sung; Wang, Xiqing; Hagaman, Edward {Ed} W; Dai, Sheng

    2013-01-01

    Rotational dynamics of the ionic liquid (IL) 1-butyl-3-methlyimidazolium bistrifluoromethylsulfonimide, [C4mim][Tf2N], 1, as a neat liquid and confined in mesoporous silica were investigated by 1H spin-spin (T2) and spin-lattice (T1) relaxation measurements and 13C NMR spectroscopy. Translational dynamics (self-diffusion) were monitored via the diffusion coefficient, D, obtained with 1H pulsed field gradient NMR measurements. These data were used to determine the distribution of 1 in the pores of KIT-6, a mesoporous silica with a bicontinuous gyroid pore structure, as a function of filling fraction. Relaxation studies performed as a function of filling factor and temperature, reveal a dynamic heterogeneity in both translational and rotational motions for 1 at filling factors, f, = 0.2-1.0 (f = 1 corresponds to fully filled pores). Spin-lattice and spin-spin relaxation times reveal the motion of 1 in silica mesopores conform to that expected for a two-dimensional relaxation model. The relaxation dynamics are interpreted using a two-state, fast exchange model for all motions; a slow rotation (and translation) of molecules in contact with the surface and a faster motion approximated by the values for bulk relaxation and diffusion. 1 retains liquid like behavior at all filling factors and temperatures that extend to ca. 50 degrees below the bulk melting point. Translational motion in these systems, interpreted with MD-simulated diffusivity limits, confirms the high propensity of 1 to form a monolayer film on the silica surface at low filling factors.. The attractive interaction of 1 with the surface is greater than that for self-association of 1. The trends in diffusion data at short and long diffusion time suggest that the population of surface-bound 1 is in intimate contact with 1 in the pores. This condition is most easily met at higher filling fractions with successive additions of 1 increasing the layer thickness built up on the surface layer.

  18. CRYSTAL POLYMORPHISM IN 1-BUTYL-3-METHYLIMIDAZOLIUM HALIDES: SUPPORTING IONIC LIQUID FORMATION THROUGH INHIBITION OF CRYSTALLIZATION. (R828257)

    EPA Science Inventory

    The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

  19. Ionic liquid 1-butyl-3-methylimidazolium cyanamide (bmim [dca]) as a solvent and catalyst for acylation of maltodextrin

    Technology Transfer Automated Retrieval System (TEKTRAN)

    We have found a novel method to prepare maltodextrin stearate with DS upto 0.60 in 90% yields from maltodextrin in IL bmim[dca] reacted with vinyl stearate or stearic acid. In this work we have demonstrated that IL could simultaneously act as a solvent and as a catalyst for reaction of maltodextrin...

  20. STRUCTURE AND PROPERTIES OF CORN, RICE, WHEAT AND POTATO STARCH DISPERSED IN THE IONIC LIQUID, 1-BUTYL-3-METHYLIMIDAZOLIUM CHLORIDE

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Ionic liquid has gained industry attention, especially in environmentally friendly green chemistry. Researchers have utilized ionic liquid for dispersing cellulose, but no report using ionic liquid for other polysaccharides. In this study, corn, rice, wheat and potato starches were dispersed in ho...

  1. Water Nanocluster Formation in the Ionic Liquid 1-Butyl-3-methylimidazolium Tetrafluoroborate ([C4mim][BF4])-D2O Mixtures.

    PubMed

    Gao, Jingsi; Wagner, Norman J

    2016-05-24

    The microstructure of mixtures of deuterated water in the ionic liquid [C4mim][BF4] is investigated by small-angle neutron scattering (SANS) measurement. In the salt-rich region, water dissolves in the ionic liquid up to 0.7 mole fraction, whereupon distinct, nanometer-sized water clusters are observed. These water nanoclusters increase in size with increasing water addition while the mole ratio of water dissolved into the ionic liquid nanostructure increases from 2 to 4. These results provide direct confirmation for recent simulations as well insight into the source of nonidealities in some thermophysical and transport properties (e.g., density and viscosity) of salt-rich aqueous mixtures reported in the literature. PMID:27152941

  2. Determination of solute partition behavior with room-temperature ionic liquid based micellar gas-liquid chromatography stationary phases using the pseudophase model.

    PubMed

    Lantz, Andrew W; Pino, Verónica; Anderson, Jared L; Armstrong, Daniel W

    2006-05-19

    The use of micelles in ionic liquid based gas-chromatography stationary phases was evaluated using equations derived for a "three-phase" model. This model allows the determination of all three partition coefficients involved in the system, and elucidates the micellar contribution to retention and selectivity. Four types of micellar-ionic liquid columns were examined in this study: 1-butyl-3-methylimidazolium chloride with sodium dodecylsulfate or dioctyl sulfosuccinate, and 1-butyl-3-methylimidazolium hexafluorophosphate with polyoxyethylene-100-stearyl ether or polyoxyethylene-23-lauryl ether. The partition coefficients were measured for a wide range of probe molecules capable of a variety of types and magnitudes of interactions. In general, most probe molecules preferentially partitioned to the micellar pseudophase over the bulk ionic liquid component of the stationary phase. Therefore, addition of surfactant to the stationary phase usually resulted in greater solute retention. It is also shown that the selectivity of the stationary phase is significantly altered by the presence of micelles, either by enhancing or lessening the separation. The effects of surfactant on the interaction parameters of the stationary phase are determined using the Abraham solvation parameter model. The addition of sodium dodecylsulfate and dioctyl sulfosuccinate to 1-butyl-3-methylimidazolium chloride stationary phases generally increased the phase's hydrogen bond basicity and increased the level of dispersion interaction. Polyoxyethylene-100-stearyl ether and polyoxyethylene-23-lauryl ether surfactants, however, enhanced the pi-pi/n-pi, polarizability/dipolarity, and hydrogen bond basicity interactions of 1-butyl-3-methylimidazolium hexafluorophosphate to a greater degree than the ionic surfactants with 1-butyl-3-methylimidazolium chloride. However, these nonionic surfactants appeared to hinder the ability of the stationary phase to interact with solutes via dispersion forces

  3. Properties of an ionic liquid-tolerant Bacillus amyloliquefaciens CMW1 and its extracellular protease.

    PubMed

    Kurata, Atsushi; Senoo, Humiya; Ikeda, Yasuyuki; Kaida, Hideaki; Matsuhara, Chiaki; Kishimoto, Noriaki

    2016-07-01

    An ionic liquid-tolerant bacterium, Bacillus amyloliquefaciens CMW1, was isolated from a Japanese fermented soybean paste. Strain CMW1 grew in the presence of 10 % (v/v) 1-butyl-3-methylimidazolium chloride ([BMIM]Cl), a commonly used ionic liquid. Additionally, strain CMW1 grew adequately in the presence of the hydrophilic ionic liquids 10 % (v/v) 1-ethyl-3-methylimidazolium trifluoromethanesulfonate ([EMIM]CF3SO3) or 2.5 % (v/v) 1-butyl-3-methylimidazolium trifluoromethanesulfonate ([BMIM]CF3SO3). Strain CMW1 produced an extracellular protease (BapIL) in the culture medium. BapIL was stable in the presence of 80 % (v/v) ionic liquids, [EMIM]CF3SO3, [BMIM]Cl, [BMIM]CF3SO3, 1-butyl-3-methylimidazolium tetrafluoroborate, 1-butyl-3-methylimidazolium hexafluorophosphate, and 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, and functioned in 10 % (v/v) these ionic liquids. BapIL was stable at pH 4.0-12.6 or in 4004 mM NaCl solution, and exhibited activity in the presence of 50 % (v/v) hydrophilic or hydrophobic organic solvents. BapIL was completely inhibited by 1 mM PMSF and partially by 5 mM EDTA. BapIL belongs to the true subtilisins according to analysis of the deduced amino acid sequence. We showed that BapIL from the ionic liquid-tolerant B. amyloliquefaciens CMW1 exhibited tolerance to ionic liquid and halo, alkaline, and organic solvents. PMID:27142029

  4. Sound velocity dispersion in room temperature ionic liquids studied using the transient grating method.

    PubMed

    Fukuda, M; Terazima, M; Kimura, Y

    2008-03-21

    Sound velocity is determined by the transient grating method in a range from 10(6) to 10(10) Hz in three room temperature ionic liquids, 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide, 1-butyl-3-methylimidazolium hexafluorophosphate, and N,N,N-trimethyl-N-propylammonium bis(trifluoromethanesulfonyl)imide. In all room temperature ionic liquids studied, the sound velocity increased with increasing frequency. The cause of this change is posited to be structural relaxation in the room temperature ionic liquids. Frequency dependence of the sound velocity is not reproduced by a simple Debye relaxation model. The sound velocity dispersion relation in 1-butyl-3-methylimidazolium hexafluorophosphate matches a Cole-Davidson function with parameters determined by a dielectric relaxation [C. Daguenet et al., J. Phys. Chem. B 110, 12682 (2006)], indicating that structural and reorientational relaxations are strongly coupled. Conversely, the sound velocity dispersions of the other two ionic liquids measured do not match those measured for dielectric relaxation, implying that structural relaxation is much faster than the reorientational relaxation. This difference is discussed in relation to the motilities of anions and cations. PMID:18361592

  5. Azido[1,1'-bis(diphenylphosphino)ferrocene](pentamethylcyclopentadienyl)rhodium(III) hexafluorophosphate.

    PubMed

    Han, Won Seok; Lee, Soon W

    2004-04-01

    In the title compound, azido-2kappaN-bis[micro-(1eta(5):2kappaP)-diphenylphosphinocyclopentadienyl][2(eta(5))-pentamethylcyclopentadienyl]iron(III)rhodium(III) hexafluorophosphate, [[Rh(C(10)H(15))(N(3))][Fe(micro-C(17)H(14)P)(2)

  6. Triarylsulfonium hexafluorophosphate salts as photoactivated acidic catalysts for ring-opening polymerisation.

    PubMed

    Barker, Ian A; Dove, Andrew P

    2013-02-11

    Triarylsulfonium hexafluorophosphate salts were shown to be effective catalysts for the ring-opening polymerisation of various cyclic monomers under UV irradiation. A dual basic/acidic catalytic system demonstrated the potential for UV-triggered formation of poly(δ-valerolactone)-b-poly(L-lactide)-b-poly(δ-valerolactone) in a 'one-pot' reaction. PMID:23283246

  7. Understanding chemical reactions of CO2 and its isoelectronic molecules with 1-butyl-3-methylimidazolium acetate by changing the nature of the cation: The case of CS2 in 1-butyl-1-methylpyrrolidinium acetate studied by NMR spectroscopy and density functional theory calculations

    NASA Astrophysics Data System (ADS)

    Cabaço, M. Isabel; Besnard, Marcel; Chávez, Fabián Vaca; Pinaud, Noël; Sebastião, Pedro J.; Coutinho, João A. P.; Danten, Yann

    2014-06-01

    NMR spectroscopy (1H, 13C, 15N) shows that carbon disulfide reacts spontaneously with 1-butyl-1-methylpyrrolidinium acetate ([BmPyrro][Ac]) in the liquid phase. It is found that the acetate anions play an important role in conditioning chemical reactions with CS2 leading, via coupled complex reactions, to the degradation of this molecule to form thioacetate anion (CH3COS-), CO2, OCS, and trithiocarbonate (CS32-). In marked contrast, the cation does not lead to the formation of any adducts allowing to conclude that, at most, its role consists in assisting indirectly these reactions. The choice of the [BmPyrro]+ cation in the present study allows disentangling the role of the anion and the cation in the reactions. As a consequence, the ensemble of results already reported on CS2-[Bmim][Ac] (1), OCS-[Bmim][Ac] (2), and CO2-[Bmim][Ac] (3) systems can be consistently rationalized. It is argued that in system (1) both anion and cation play a role. The CS2 reacts with the acetate anion leading to the formation of CH3COS-, CO2, and OCS. After these reactions have proceeded the nascent CO2 and OCS interact with the cation to form imidazolium-carboxylate ([Bmim] CO2) and imidazolium-thiocarboxylate ([Bmim] COS). The same scenario also applies to system (2). In contrast, in the CO2-[Bmim] [Ac] system a concerted cooperative process between the cation, the anion, and the CO2 molecule takes place. A carbene issued from the cation reacts to form the [Bmim] CO2, whereas the proton released by the ring interacts with the anion to produce acetic acid. In all these systems, the formation of adduct resulting from the reaction between the solute molecule and the carbene species originating from the cation is expected. However, this species was only observed in systems (2) and (3). The absence of such an adduct in system (1) has been theoretically investigated using DFT calculations. The values of the energetic barrier of the reactions show that the formation of [Bmim] CS2 is unfavoured and that the anion offers a competitive reactive channel via an oxygen-sulphur exchange mechanism with the solute in systems (1) and (2).

  8. Understanding chemical reactions of CO{sub 2} and its isoelectronic molecules with 1-butyl-3-methylimidazolium acetate by changing the nature of the cation: The case of CS{sub 2} in 1-butyl-1-methylpyrrolidinium acetate studied by NMR spectroscopy and density functional theory calculations

    SciTech Connect

    Cabaço, M. Isabel; Besnard, Marcel; Danten, Yann; Chávez, Fabián Vaca; Pinaud, Noël; Sebastião, Pedro J.; Coutinho, João A. P.

    2014-06-28

    NMR spectroscopy ({sup 1}H, {sup 13}C, {sup 15}N) shows that carbon disulfide reacts spontaneously with 1-butyl-1-methylpyrrolidinium acetate ([BmPyrro][Ac]) in the liquid phase. It is found that the acetate anions play an important role in conditioning chemical reactions with CS{sub 2} leading, via coupled complex reactions, to the degradation of this molecule to form thioacetate anion (CH{sub 3}COS{sup −}), CO{sub 2}, OCS, and trithiocarbonate (CS{sub 3}{sup 2−}). In marked contrast, the cation does not lead to the formation of any adducts allowing to conclude that, at most, its role consists in assisting indirectly these reactions. The choice of the [BmPyrro]{sup +} cation in the present study allows disentangling the role of the anion and the cation in the reactions. As a consequence, the ensemble of results already reported on CS{sub 2}-[Bmim][Ac] (1), OCS-[Bmim][Ac] (2), and CO{sub 2}-[Bmim][Ac] (3) systems can be consistently rationalized. It is argued that in system (1) both anion and cation play a role. The CS{sub 2} reacts with the acetate anion leading to the formation of CH{sub 3}COS{sup −}, CO{sub 2}, and OCS. After these reactions have proceeded the nascent CO{sub 2} and OCS interact with the cation to form imidazolium-carboxylate ([Bmim] CO{sub 2}) and imidazolium-thiocarboxylate ([Bmim] COS). The same scenario also applies to system (2). In contrast, in the CO{sub 2}-[Bmim] [Ac] system a concerted cooperative process between the cation, the anion, and the CO{sub 2} molecule takes place. A carbene issued from the cation reacts to form the [Bmim] CO{sub 2}, whereas the proton released by the ring interacts with the anion to produce acetic acid. In all these systems, the formation of adduct resulting from the reaction between the solute molecule and the carbene species originating from the cation is expected. However, this species was only observed in systems (2) and (3). The absence of such an adduct in system (1) has been theoretically investigated using DFT calculations. The values of the energetic barrier of the reactions show that the formation of [Bmim] CS{sub 2} is unfavoured and that the anion offers a competitive reactive channel via an oxygen-sulphur exchange mechanism with the solute in systems (1) and (2)

  9. Application of cold-induced aggregation microextraction as a fast, simple, and organic solvent-free method for the separation and preconcentration of Se(IV) in rice and various water samples.

    PubMed

    Rahnama, Reyhaneh; Abed, Zinat

    2014-07-01

    The developed method is based on cold-induced aggregation microextraction of Se(IV) using the 1-butyl-3-methylimidazolium hexafluorophosphate ionic liquid as an extractant followed by spectrophotometry determination. The extraction of Se(IV) was performed in the presence of dithizone as the complexing agent. In this method, a very small amount of 1-butyl-3-methylimidazolium hexafluorophosphate was added to the sample solution containing Se-dithizone complex. Then, the solution was kept in a thermostated bath at 50 °C for 4 min. Subsequently, the solution was cooled in an ice bath and a cloudy solution was formed. After centrifuging, the extractant phase was analyzed using a spectrophotometric detection method. Some important parameters that might affect the extraction efficiency were optimized (HCl, 0.6 mol L(-1); dithizone, 4.0 × 10(-6) mol L(-1); ionic liquid, 100 μL). Under the optimum conditions, good linear relationship, sensitivity, and reproducibility were obtained. The limit of detection (LOD) (3Sb/m) was 1.5 μg L(-1), and the relative standard deviation (RSD) was 1.2 % for 30 μg L(-1) of Se(IV). The linear range was obtained in the range of 5-60 μg L(-1). It was satisfactory to analyze rice and various water samples. PMID:24590231

  10. Determination of rifaximin in rat serum by ionic liquid based dispersive liquid-liquid microextraction combined with RP-HPLC.

    PubMed

    Rao, Ramisetti Nageswara; Vali, Rajavarapu Mastan; Rao, Alamanda Vara Prasada

    2012-08-01

    An efficient and environmental friendly ionic liquid based dispersive liquid-liquid microextraction procedure was optimized for determination of rifaximin in rat serum by reverse phase high-performance liquid chromatography. The effect of ionic liquids, dispersive solvents, extractant/disperser ratio, and salt concentrations on sample recovery and enrichment factors were studied. Among the five ionic liquids studied in the present investigation, 1-butyl-3-methylimidazolium hexafluorophosphate was found to be most effective for extraction of rifaximin. The recovery was found to be more than 98% using 1-butyl-3-methylimidazolium hexafluorophosphate and methanol as extraction and dispersive solvents, at an extractant/disperser ratio of 0.43. The recovery was further enhanced to 99.5% by the addition of 5.0% NaCl solution. A threefold enhancement in detection limit was achieved when compared to protein precipitation. The ionic liquid containing the extracted rifaximin was directly injected into HPLC system. The linear relationship was observed in the range of 0.03-10.0 μg/mL with the correlation coefficient (r(2)) 0.9998. Limits of detection and quantification were found to be 0.01 and 0.03 μg/mL, respectively. The relative standard deviation was 2.5%. The method was validated and applied to study pharmacokinetics of rifaxmin in rat serum. PMID:22753340

  11. Ionic liquid-based dispersive liquid-liquid microextraction followed by RP-HPLC determination of saquinavir in rat serum: application to pharmacokinetics.

    PubMed

    Ramisetti, Nageswara Rao; Nimmu, Narendra Varma; Challa, Gangu Naidu

    2014-12-01

    An ionic liquid-based dispersive liquid-liquid microextraction followed by RP-HPLC determination of the most commonly prescribed protease inhibitor, saquinavir, in rat plasma was developed and validated. The effects of different ionic liquids, dispersive solvents, extractant/disperser ratio and salt concentration on sample recovery and enrichment were studied. Among the ionic liquids investigated, 1-butyl-3-methylimidazolium hexafluorophosphate was found to be most effective for extraction of saquinavir from rat serum. The recovery was found to be 95% at an extractant/disperser ratio of 0.43 using 1-butyl-3-methylimidazolium hexafluorophosphate and methanol as extraction and dispersive solvents. The recovery was further enhanced to 99.5% by addition of 5.0% NaCl. A threefold enhancement in detection and quantification limits was achieved, at 0.01 and 0.03 µg/mL, compared with the conventional protein precipitation method. A linear relationship was observed in the range of 0.035-10.0 µg/mL with a correlation coefficient (r(2) ) of 0.9996. The method was validated and applied to study pharmacokinetics of saquinavir in rat serum. PMID:24944096

  12. Immobilization of pectinase on silica-based supports: Impacts of particle size and spacer arm on the activity.

    PubMed

    Alagöz, Dilek; Tükel, S Seyhan; Yildirim, Deniz

    2016-06-01

    The pectinase was separately immobilized onto Florisil and nano silica supports through both glutaraldehyde and 3-glyoxypropyltrietoxysilane spacer arms. The effects of spacer arm, particle size of support and ionic liquids on the activities of pectinase preparations were investigated. The immobilization of pectinase onto Florisil and nano silica through 3-glyoxypropyltrietoxysilane spacer arm completely led to inactivation of enzyme; however, 10 and 75% pectinase activity were retained when it was immobilized through glutaraldehyde spacer arm onto Florisil and nano silica, respectively. The pectinase immobilized onto nano silica through glutaraldehyde spacer arm showed 6.3-fold higher catalytic efficiency than that of the pectinase immobilized onto Florisil through same spacer arm. A 2.3-fold increase in thermal stability of pectinase was provided upon immobilization onto nano silica at 35°C. The effects of IL/buffer mixture and volume ratio of IL/buffer mixture on the catalytic activities of free and immobilized pectinase preparations were also tested. All the pectinase preparations showed highest activity in 10% (v/v) 1-butyl-3-methylimidazolium hexafluorophosphate containing medium and their activities significantly affected from the concentration of 1-butyl-3-methylimidazolium hexafluorophosphate. PMID:26964525

  13. Dynamics of Loop 1 of Domain I in Human Serum Albumin WhenDissolved in Ionic Liquids

    SciTech Connect

    Page, Taylor; Kraut, Nadine; Page, Phillip; Baker, Gary A; Bright, Frank

    2009-01-01

    We report on the rotational reorientation dynamics associated with loop 1 of domain I within a large multidomain protein (human serum albumin, HSA) when it is dissolved in binary mixtures of ionic liquid (1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C4mim][Tf2N]), 1-butyl-3-methylimidazolium tetrafluoroborate ([C4mim][BF4]), or 1-butyl-3-methylimidazolium hexafluorophosphate ([C4mim][PF6])) and distilled deionized water (ddH2O) as a function of temperature and water loading. In IL/2% ddH2O (v/v) mixtures, loop 1 of domain I is more significantly denatured in comparison to the protein dissolved in aqueous solutions containing strong chemical denaturants (e.g., 8 M guanidine HCl (Gu HCl) or urea). As water loading increases, there is evidence for progressive refolding of loop 1 of domain I followed by recoupling with domains I, II, and III in the [C4mim][BF4]/ddH2O mixtures at 20 C. Above 30% (v/v) water, where domain I appears refolded, the Ac reporter molecule s semiangle steadily decreases from 35 to 20 with increasing water loading. From the perspective of domain I in HSA, this behavior is similar to the effects of dilution from 4 to 0 M Gu HCl in aqueous solution. Overall, these results lend insight into the tangle of biocatalytic and structural/dynamical mechanisms that enzymes may undergo in ionic liquid-based systems. It will be particularly motivating to extend this work to include enzyme-attuned ionic liquids shown to improve biocatalytic performance beyond that possible in the native (predominantly aqueous) setting.

  14. Morphology of 1-alkyl-3-methylimidazolium hexafluorophosphate room temperature ionic liquids

    NASA Astrophysics Data System (ADS)

    Triolo, Alessandro; Russina, Olga; Fazio, Barbara; Triolo, Roberto; Di Cola, Emanuela

    2008-05-01

    The structural organization in selected room temperature ionic liquids, namely (a) butyl-, (b) hexyl- and (c) octyl-3-methylimidazolium hexafluorophosphate, is investigated by means of X-ray diffraction. We find novel experimental evidences of the existence of a high degree of intermediate range order that is associated to nanoscale segregation of the alkyl chains into the charged matrix. The size of these structural heterogeneities depends linearly from the alkyl chain length. A similar behaviour had been observed in other systems, such as normal alcohols. The slope of such dependence provides hints on the nature of the structural organization of these segregated domains.

  15. Thermal decomposition and vibrational spectroscopic aspects of pyridinium hexafluorophosphate (C5H5NHPF6)

    NASA Astrophysics Data System (ADS)

    Lekgoathi, M. D. S.; Kock, L. D.

    2016-12-01

    Thermal decomposition and vibrational spectroscopic properties of pyridinium hexafluorophosphate (C5H5NHPF6) have been studied. The structure of the compound is better interpreted as having a cubic space group, based on Raman and infrared vibrational spectroscopy experiments and group theoretical correlation data between site symmetry species and the spectroscopic space group. The 13C NMR data shows three significant signals corresponding to the three chemical environments expected on the pyridinium ring i.e. γ, β and α carbons, suggesting that the position of the anion must be symmetrical with respect to the pyridinium ring's C2v symmetry. The process of thermal decomposition of the compound using TGA methods was found to follow a contracting volume model. The activation energy associated with the thermal decomposition reaction of the compound is 108.5 kJ mol-1, while the pre exponential factor is 1.51 × 109 sec-1.

  16. Synthesis of Bis(1,2-Dimethylimidazole)Copper(I)Hexafluorophosphate: An Experiment Using a Glove Box

    ERIC Educational Resources Information Center

    Niewahner, J. H.; Walters, Keith A.

    2007-01-01

    A detailed description of the synthesis of bis(1,2-dimethylimidazole)copper(I) hexafluorophosphate by using techniques in a glove box is presented. The results shows that the synthesis of the copper complex has a distinct color change indicating by-product oxidation by oxygen.

  17. Oxidative stress in spring barley and common radish exposed to quaternary ammonium salts with hexafluorophosphate anion.

    PubMed

    Biczak, Robert; Telesiński, Arkadiusz; Pawłowska, Barbara

    2016-10-01

    Quaternary ammonium salts (QAS), including ionic liquids (ILs), constitute a huge group of substances, which due to their desirable physical and chemical properties still attracts great interest in many industrial sectors. An increased concentration of this compound in the environment may lead to the contamination of the natural environment and may pose a potential threat to all organisms, including terrestrial higher plants. The present study demonstrates the interaction of three QAS with PF6(-) anions - tetramethylammonium [TMA][PF6], tetrabutylammonium [TBA][PF6], and tetrahexylammonium [THA][PF6] hexafluorophosphates - and its impact on the physiological and biochemical changes in spring barley seedlings and common radish plants. A similar study was also carried out by introducing the inorganic salt - ammonium hexafluorophosphate [A][PF6] to the soil; the results showed the soil became highly toxic to both plants. All the salts used led to significant changes in the metabolism of both spring barley and common radish which can be evidenced, for example, by a decrease in the content of chlorophyll a (Chla), chlorophyll b (Chlb), and total chlorophyll (Chla + b), as well as carotenoids (Car). The decrease in assimilation pigments was linearly correlated with an increasing concentration of QAS in the soil. QAS and [A][PF6] led to the formation of oxidative stress in both experimental plants, as evidenced by an increase in malondialdehyde (MDA) content in their cells and the changes in H2O2 level. In response to stress, the plants synthesized enzymatic free radicals (ROS) scavengers that lead to changes in the activity of superoxide dismutase (SOD) and catalase (CAT), as well as significantly increased peroxidase (POD) activity. A decrease in the content of assimilation pigments and an increased POD activity are the most reliable indices of oxidative stress, and concurrently the signs of premature plants aging. Common radish proved to be more resistant to the

  18. Electrical, structural, thermal and electrochemical properties of corn starch-based biopolymer electrolytes.

    PubMed

    Liew, Chiam-Wen; Ramesh, S

    2015-06-25

    Biopolymer electrolytes containing corn starch, lithium hexafluorophosphate (LiPF6) and ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate (BmImPF6) are prepared by solution casting technique. Temperature dependence-ionic conductivity studies reveal Vogel-Tamman-Fulcher (VTF) relationship which is associated with free volume theory. Ionic liquid-based biopolymer electrolytes show lower glass transition temperature (Tg) than ionic liquid-free biopolymer electrolyte. X-ray diffraction (XRD) studies demonstrate higher amorphous region of ionic liquid-added biopolymer electrolytes. In addition, the potential stability window of the biopolymer electrolyte becomes wider and stable up to 2.9V. Conclusively, the fabricated electric double layer capacitor (EDLC) shows improved electrochemical performance upon addition of ionic liquid into the biopolymer electrolyte. The specific capacitance of EDLC based on ionic liquid-added polymer electrolyte is relatively higher than that of ionic liquid-free polymer electrolyte as depicted in cyclic voltammogram. PMID:25839815

  19. Determining diffusion coefficients of ionic liquids by means of field cycling nuclear magnetic resonance relaxometry.

    PubMed

    Kruk, D; Meier, R; Rachocki, A; Korpała, A; Singh, R K; Rössler, E A

    2014-06-28

    Field Cycling Nuclear Magnetic Resonance (FC NMR) relaxation studies are reported for three ionic liquids: 1-ethyl-3- methylimidazolium thiocyanate (EMIM-SCN, 220-258 K), 1-butyl-3-methylimidazolium tetrafluoroborate (BMIM-BF4, 243-318 K), and 1-butyl-3-methylimidazolium hexafluorophosphate (BMIM-PF6, 258-323 K). The dispersion of (1)H spin-lattice relaxation rate R1(ω) is measured in the frequency range of 10 kHz-20 MHz, and the studies are complemented by (19)F spin-lattice relaxation measurements on BMIM-PF6 in the corresponding frequency range. From the (1)H relaxation results self-diffusion coefficients for the cation in EMIM-SCN, BMIM-BF4, and BMIM-PF6 are determined. This is done by performing an analysis considering all relevant intra- and intermolecular relaxation contributions to the (1)H spin-lattice relaxation as well as by benefiting from the universal low-frequency dispersion law characteristic of Fickian diffusion which yields, at low frequencies, a linear dependence of R1 on square root of frequency. From the (19)F relaxation both anion and cation diffusion coefficients are determined for BMIM-PF6. The diffusion coefficients obtained from FC NMR relaxometry are in good agreement with results reported from pulsed- field-gradient NMR. This shows that NMR relaxometry can be considered as an alternative route of determining diffusion coefficients of both cations and anions in ionic liquids. PMID:24985656

  20. Extraction of arsenic in a soil of the blackfoot disease endemic area with ionic liquids

    NASA Astrophysics Data System (ADS)

    Liao, C.-Y.; Wang, H. Paul; Peng, C.-Y.; Kang, H.-Y.; Wei, Y.-L.

    2009-04-01

    Speciation of arsenic in the soil of the old blackfoot disease endemic area in the Southern Taiwan has been studied by X-ray absorption near edge structural (XANES) and extended X-ray absorption fine structural (EXAFS) spectroscopy. Experimentally, at the contact time of 30-180 min, 30-40% of As(III) and 40-60% of As(V) in the soil can be extracted with a room temperature ionic liquid (RTIL) [BMI][BF4] (1-butyl-3-methylimidazolium tetrafluoroborate). For the relatively hydrophobic RTIL [BMI][PF6] (1-butyl-3-methylimidazolium hexafluorophosphate), on the contrary, 10-15% of As(III) and 20-25% of As(V) can be extracted. By XANES, it is found that an enhanced oxidation of the extracted As(III) (As(III)→As(V)) in the RTIL may occur during the extraction processes. The refined EXAFS spectra also indicate that the bond distances of As(III)-N and As(V)-N in the arsenic-extracted RTILs are 1.76-1.78 and 1.68-1.70

  1. Extraction of arsenic from a soil in the blackfoot disease endemic area with ionic liquids

    NASA Astrophysics Data System (ADS)

    Liao, Chang-Yu; Peng, Ching-Yu; Wang, Hong-Chung; Kang, Hsu-Ya; Paul Wang, H.

    2011-10-01

    Speciation of arsenic extracted with room temperature ionic liquids (RTILs) ([bmim][BF 4] (1-butyl-3-methylimidazolium tetrafluoroborate) and [bmim][PF 6] (1-butyl-3-methylimidazolium hexafluorophosphate)) from an As-humic acid (As-HA) complex contaminated soil (As-HA/soil) in a blackfoot disease endemic area has been studied by X-ray absorption (near edge structure (XANES) and extended X-ray absorption fine structure (EXAFS)) spectroscopy. About 45% of arsenic in the As-HA/soil can be extracted with [bmim][BF 4] while the relatively less hydrophilic [bmim][PF 6] extracts 25% of arsenic. The extracted arsenic in the [bmim][BF 4] and [bmim][PF 6] from the As-HA/soil possesses mainly As(III) species, suggesting that at least two reaction paths may be involved in the extraction process: (1) splitting of As-HA and (2) reduction of As(V) to As(III). The refined EXAFS spectra also indicate that the As(III) extracted in the RTILs possesses the AsO 2- structure, which has the As-O bond distances of 1.77-1.79 Å and coordination numbers of 4.0-4.2.

  2. Determining diffusion coefficients of ionic liquids by means of field cycling nuclear magnetic resonance relaxometry

    NASA Astrophysics Data System (ADS)

    Kruk, D.; Meier, R.; Rachocki, A.; Korpała, A.; Singh, R. K.; Rössler, E. A.

    2014-06-01

    Field Cycling Nuclear Magnetic Resonance (FC NMR) relaxation studies are reported for three ionic liquids: 1-ethyl-3- methylimidazolium thiocyanate (EMIM-SCN, 220-258 K), 1-butyl-3-methylimidazolium tetrafluoroborate (BMIM-BF4, 243-318 K), and 1-butyl-3-methylimidazolium hexafluorophosphate (BMIM-PF6, 258-323 K). The dispersion of 1H spin-lattice relaxation rate R1(ω) is measured in the frequency range of 10 kHz-20 MHz, and the studies are complemented by 19F spin-lattice relaxation measurements on BMIM-PF6 in the corresponding frequency range. From the 1H relaxation results self-diffusion coefficients for the cation in EMIM-SCN, BMIM-BF4, and BMIM-PF6 are determined. This is done by performing an analysis considering all relevant intra- and intermolecular relaxation contributions to the 1H spin-lattice relaxation as well as by benefiting from the universal low-frequency dispersion law characteristic of Fickian diffusion which yields, at low frequencies, a linear dependence of R1 on square root of frequency. From the 19F relaxation both anion and cation diffusion coefficients are determined for BMIM-PF6. The diffusion coefficients obtained from FC NMR relaxometry are in good agreement with results reported from pulsed- field-gradient NMR. This shows that NMR relaxometry can be considered as an alternative route of determining diffusion coefficients of both cations and anions in ionic liquids.

  3. Ionic liquid based hollow fiber supported liquid phase microextraction of ultraviolet filters.

    PubMed

    Ge, Dandan; Lee, Hian Kee

    2012-03-16

    Hollow fiber protected liquid phase microextraction using an ionic liquid as supported phase and acceptor phase (IL-HF-LPME) is proposed for the determination of four ultraviolet (UV) filters (benzophenone, 3-(4-methylbenzylidene)-camphor, 2-hydroxy-4-methoxybenzophenone and 2,4-dihydroxybenzophenone) in water samples for the first time. In the present study, four different ILs 1-hexyl-3-methylimidazolium tris(pentafluoroethyl)trifluorophosphate) [HMIM][FAP], 1-butyl-1-methylpyrrolidinium tris(pentafluoroethyl)trifluorophosphate [BMPL][FAP], 1-butyl-3-methylimidazolium phosphate ([BMIM][PO(4)]) and 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF(6)]) were evaluated as extraction solvent. Only [HMIM][FAP] showed high chemical affinity to the analytes which permits a selective isolation of the UV filters from the sample matrix, allowing also their preconcentration. IL-HF-LPME and high performance liquid chromatography provides repeatability from 1.1% to 8.2% and limits of detection between 0.3 and 0.5 ng/ml. Real water samples spiked with the analytes extracted were analyzed, and yielded relative recoveries ranging from 82.6% to 105.9%. PMID:22307149

  4. Recombination of Photogenerated Lophyl Radicals in Imidazolium-Based Ionic Liquids

    SciTech Connect

    Strehmel, V.; Wishart, J.; Polyansky, D.E.; Strehmel, B.

    2009-10-20

    Laser flash photolysis is applied to study the recombination reaction of lophyl radicals in ionic liquids in comparison with dimethylsulfoxide as an example of a traditional organic solvent. The latter exhibits a similar micropolarity as the ionic liquids. The ionic liquids investigated are 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (1), 1-hexyl-3-methylimidazolium hexafluorophosphate (2), and 1-butyl-3-methylimidazolium tetafluoroborate (3). The recombination of the photolytic generated lophyl radicals occur significantly faster in the ionic liquids than expected from their macroscopic viscosities and is a specific effect of these ionic liquids. On the other hand, this reaction can be compared with the macroscopic viscosity in the case of dimethylsulfoxide. Activation parameters obtained for lophyl radical recombination suggest different, anion-dependent mechanistic effects. Quantum chemical calculations based on density functional theory provide a deeper insight of the molecular properties of the lophyl radical and its precursor. Thus, excitation energies, spin densities, molar volumes, and partial charges are calculated. Calculations show a spread of spin density over the three carbon atoms of the imidazolyl moiety, while only low spin density is calculated for the nitrogens.

  5. Atomistic simulation of structure and dynamics of the plastic crystal diethyl(methyl)(isobutyl)phosphonium hexafluorophosphate

    NASA Astrophysics Data System (ADS)

    Chen, F.; Jin, L.; de Leeuw, S. W.; Pringle, J. M.; Forsyth, M.

    2013-06-01

    Molecular dynamics simulations have been performed to investigate the interrelations between structures, transport mechanisms, and phase transitions of an organic ionic plastic crystal material, diethyl(methyl)(isobutyl)phosphonium hexafluorophosphate ([P1,2,2,4][PF6]), in both solid and liquid phases. Examination of the temperature dependence of supercell parameters and radial distribution functions provides evidence of plastic phase transitions. Nonlinear increments of cell size within the temperature range 123-413 K are consistent with the plastic phase transitions identified from experimental analysis. The time- and temperature-dependent microstructure and dynamics have been intensively studied through analysis of trajectory files. The rotational motion and diffusion of the matrix ions are quantitatively analysed via rotational correlation functions and mean square displacements. We present new information on the evolution of molecular motions in different phases, and compare and contrast our findings with previously reported hypotheses based on nuclear magnetic resonance results. This work provides valuable information at an atomistic level to explain the experimental observations, which helps further understanding of the molecular motions underlying the plastic phase transitions.

  6. Ion gels by self-assembly of a triblock copolymer in an ionic liquid.

    PubMed

    He, Yiyong; Boswell, Paul G; Bühlmann, Philippe; Lodge, Timothy P

    2007-05-10

    We report a new way of developing ion gels through the self-assembly of a triblock copolymer in a room-temperature ionic liquid. Transparent ion gels were achieved by gelation of a poly(styrene-block-ethylene oxide-block-styrene) (SOS) triblock copolymer in 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF6]) with as low as 5 wt % SOS triblock copolymer. The gelation behavior, ionic conductivity, rheological properties, and microstructure of the ion gels were investigated. The ionic conductivity of the ion gels is only modestly affected by the triblock copolymer network. Its temperature dependence nearly tracks that of the bulk ionic liquid viscosity. The ion gels are thermally stable up to at least 100 degrees C and possess significant mechanical strength. The results presented here suggest that triblock copolymer gelation is a promising way to develop highly conductive ion gels and provides many advantages in terms of variety and processing. PMID:17474692

  7. The effects of anion and cation substitution on the ultrafast solvent dynamics of ionic liquids: A time-resolved optical Kerr-effect spectroscopic study

    NASA Astrophysics Data System (ADS)

    Giraud, Gerard; Gordon, Charles M.; Dunkin, Ian R.; Wynne, Klaas

    2003-07-01

    Ultrafast solvent dynamics of room-temperature ionic liquids have been investigated by optical heterodyne-detected Raman-induced Kerr-effect spectroscopy (OHD-RIKES) by studying the effects of cation and anion substitution on the low frequency librational modes. The spectra of two series of imidazolium salts are presented. The first series is based on the 1-butyl-3-methylimidazolium salts [bmim]+ containing the anions trifluoromethanesulfate [TfO]-, bis(trifluoromethanesulfonyl)imide [Tf2N]-, and hexafluorophosphate [PF6]-. The second series is based on [Tf2N]- salts containing the three cations 1-butyl-2,3-dimethylimidazolium [bmmim]+, 1-methyl-3-octylimidazolium [omim]+, and [bmim]+. It is found in all five samples that the signal is due to libration of the imidazolium ring at three frequencies around 30, 65, and 100 cm-1 corresponding to three local configurations of the anion with respect to the cation.

  8. The Effect of Microporous Polymeric Support Modification on Surface and Gas Transport Properties of Supported Ionic Liquid Membranes

    PubMed Central

    Akhmetshina, Alsu A.; Davletbaeva, Ilsiya M.; Grebenschikova, Ekaterina S.; Sazanova, Tatyana S.; Petukhov, Anton N.; Atlaskin, Artem A.; Razov, Evgeny N.; Zaripov, Ilnaz I.; Martins, Carla F.; Neves, Luísa A.; Vorotyntsev, Ilya V.

    2015-01-01

    Microporous polymers based on anionic macroinitiator and toluene 2,4-diisocyanate were used as a support for 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF6]) and 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([emim][Tf2N]) immobilization. The polymeric support was modified by using silica particles associated in oligomeric media, and the influence of the modifier used on the polymeric structure was studied. The supported ionic liquid membranes (SILMs) were tested for He, N2, NH3, H2S, and CO2 gas separation and ideal selectivities were calculated. The high values of ideal selectivity for ammonia-based systems with permanent gases were observed on polymer matrixes immobilized with [bmim][PF6] and [emim][Tf2N]. The modification of SILMs by nanosize silica particles leads to an increase of NH3 separation relatively to CO2 or H2S. PMID:26729177

  9. Sensitive determination of Amaranth in drinks by highly dispersed CNT in graphene oxide "water" with the aid of small amounts of ionic liquid.

    PubMed

    Wang, Meiling; Sun, Yinlu; Yang, Xiongbo; Zhao, Jianwei

    2015-07-15

    Graphene oxide (GO) is a pH-dependent amphiphile. In this paper, it was found that carbon nanotubes (CNTs) can be highly dispersed in graphene oxide "water" with the aid of prototype ionic liquid of 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF6]). The introduction of [BMIM][PF6] not only can minimize the defects of poor electrical conductivity of GO, but also can improve the dispersibility of CNT in water. Hence, a new composite of CNT/GO-[BMIM][PF6] with high dispersibility and strong conductivity was presented for the first time and employed in the sensitive determination of Amaranth in soft drinks. The detection limit achieved (0.1 nM) is much lower than the guideline values in soft drinks. The ease of preparation, low background current, high sensitivity and stability can create novel avenues and applications for fabricating robust sensors for determination of other azo dyes in foods. PMID:25722171

  10. Optimization of covalent immobilization of Trichoderma reesei cellulase onto modified ReliZyme HA403 and Sepabeads EC-EP supports for cellulose hydrolysis, in buffer and ionic liquids/buffer media.

    PubMed

    Bilgin, Ramazan; Yalcin, M Serkan; Yildirim, Deniz

    2016-08-01

    The covalent immobilization of Trichoderma reesei cellulase onto modified ReliZyme HA403 and Sepabeads EC-EP supports were carried out. The optimal immobilization conditions were determined using response surface methodology. The hydrolysis of cellulose using the free and immobilized cellulase preparations in ionic liquids (IL) using cosolvents was investigated. The hydrolytic activities in buffer medium containing 25% (v/v) of 1-butyl-3-methylimidazolium hexafluorophosphate were around 2.6-, 1.6-, and 5.5-fold higher than the activities in buffer medium. The retained initial activities were 32% and 57%, respectively for cellulase preparations immobilized onto Sepabeads EC-EP support and onto modified ReliZyme HA403 support after 5 reuses. PMID:25811997

  11. Ionic liquid-based single drop microextraction of ultra-trace copper in food and water samples before spectrophotometric determination

    NASA Astrophysics Data System (ADS)

    Wen, Xiaodong; Deng, Qingwen; Guo, Jie

    2011-09-01

    In this work, room temperature ionic liquid (RTIL) 1-butyl-3-methylimidazolium hexafluorophosphate ([C 4mim]PF 6) was used as extractant in single drop microextraction (SDME). The traditionally volatile organic extractants were substituted by this green reagent, which changed SDME preconcentration into environmentally friendly method, relatively. After this pretreatment, ultra-trace copper in water and food samples could be accurately detected by spectrophotometer. This study was focused on the improvement of the analytical performance of spectrophotometric determination, expanding its applications. The influence factors relevant to IL-SDME, such as absorption spectra of complex, drop volume of RTIL, stirring rate and time, concentration of chelating agent, pH, and salt effect were studied systematically. Under the optimal conditions, the limit of detection (LOD) was 0.15 μg L -1 with an enhancement factor (EF) of 33. The proposed method was green, simple, rapid, sensitive, and cost-efficient.

  12. Preparation of starch nanoparticles in a water-in-ionic liquid microemulsion system and their drug loading and releasing properties.

    PubMed

    Zhou, Gang; Luo, Zhigang; Fu, Xiong

    2014-08-13

    An ionic liquid microemulsion consisting of 1-butyl-3-methylimidazolium hexafluorophosphate ([Bmim]PF₆), surfactant TX-100, 1-butanol, and water was prepared. The water-in-[Bmim]PF₆ (W/IL), bicontinuous, and [Bmim]PF₆-in-water (IL/W) microregions of the microemulsion were identified by conductivity measurements. Starch nanoparticles with a mean diameter of 91.4 nm were synthesized with epichlorohydrin as cross-linker through W/IL microemulsion cross-linking reaction at 50 °C for 4 h. Fourier transform infrared spectroscopy (FTIR) data demonstrated the formation of cross-linking bonds in starch molecules. Scanning electron microscopy (SEM) revealed that starch nanoparticles were spherical and that some particles showed aggregation formation. Furthermore, drug loading and releasing properties of starch nanoparticles were investigated with mitoxantrone hydrochloride as a drug model. This work provides an efficient and environmentally friendly approach for the preparation of starch nanoparticles, which is beneficial to their further application. PMID:25069988

  13. Ultrasound-assisted ionic liquid-based dispersive liquid-liquid microextraction for preconcentration of patent blue V and its determination in food samples by UV-visible spectrophotometry.

    PubMed

    Unsal, Yunus Emre; Soylak, Mustafa; Tuzen, Mustafa

    2015-04-01

    Ultrasound-assisted ionic liquid-based dispersive liquid-liquid microextraction procedure (UA-IL-DLLME) was developed for determination of trace levels of patent blue V prior to its determination by UV-visible spectrophotometry. Patent blue V was extracted from 25-mL sample into a 100-μL volume of ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF6]), with the aid of sonication in an ultrasonic bath. Several variables affecting microextraction efficiency were optimized. Under the optimum experimental conditions, the detection limit (3 s) was 0.68 μg L(-1), and the preconcentration factor was 100. The relative standard deviation for six replicate determinations of patent blue V was 4.5%. The method was applied to the determination of patent blue V in food samples. The proposed procedure is effective, very simple, and fast. PMID:25800367

  14. Effect of Room Temperature Ionic Liquid on the Formation of the Complex Oxalate-Sodium Morin-5-Sulfonate-Aluminium(III): Application to the Fluorescence Determination of Oxalate Ion.

    PubMed

    Nizar, Syaza Atikah; Mohd Suah, Faiz Bukhari

    2016-07-01

    The effect of room temperature ionic liquid (RTIL) on the formation of the fluorescence ternary complex oxalate-sodium morin-5-sulfonate (NaMSA)-Aluminium(III) has been studied. In weakly acidic medium and in the presence of RTIL, 1-Butyl-3-methylimidazolium hexafluorophosphate (BMIM-PF6), total complex formation is achieved as compared with the formation of the binary complex of NaMSA-Aluminium(III). The fluorescence characteristics of the system allowed the establishment of a very sensitive method for the spectrofluorimetric determination of oxalate ion. The ternary complex formed its highest fluorescence signal at 513 nm and excitation at 420 nm. In these conditions, the method produces a detection limit of 0.57 ng mL(-1). The procedure has been satisfactorily applied to the determination of oxalate ion in a vegetal tissue (spinach leaves). PMID:27286697

  15. Theoretical investigation of polarization effects in solution: Importance of solvent collective motions

    SciTech Connect

    Ishida, Tateki

    2015-01-22

    Recent theoretical studies on interesting topics related to polarization effects in solutions are presented. As one of interesting topics, ionic liquids (ILs) solvents are focused on. The collective dynamics of electronic polarizability through interionic dynamics and the effect of polarization in ILs, 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIm][PF{sub 6}]), are studied with molecular dynamics simulation. Also, the time-dependent polarization effect on the probe betaine dye molecule, pyridinium N-phenoxide, in water is investigated by a time-dependent reference interaction site model self-consistent field (time-dependent RISM-SCF) approach. The importance of considering polarization effects on solution systems related to solvent collective motions is shown.

  16. Development of Ionic Liquid Modified Disposable Graphite Electrodes for Label-Free Electrochemical Detection of DNA Hybridization Related to Microcystis spp.

    PubMed Central

    Sengiz, Ceren; Congur, Gulsah; Erdem, Arzum

    2015-01-01

    In this present study, ionic liquid (1-butyl-3-methylimidazolium hexafluorophosphate (IL)) modified pencil graphite electrode (IL-PGEs) was developed for electrochemical monitoring of DNA hybridization related to Microcystis spp. (MYC). The characterization of IL-PGEs was performed using microscopic and electrochemical techniques. DNA hybridization related to MYC was then explored at the surface of IL-PGEs using differential pulse voltammetry (DPV) technique. After the experimental parameters were optimized, the sequence-selective DNA hybridization related to MYC was performed in the case of hybridization between MYC probe and its complementary DNA target, noncomplementary (NC) or mismatched DNA sequence (MM), or and in the presence of mixture of DNA target: NC (1:1) and DNA target: MM (1:1). PMID:26371004

  17. Determining diffusion coefficients of ionic liquids by means of field cycling nuclear magnetic resonance relaxometry

    SciTech Connect

    Kruk, D.; Meier, R.; Rössler, E. A.; Rachocki, A.; Korpała, A.; Singh, R. K.

    2014-06-28

    Field Cycling Nuclear Magnetic Resonance (FC NMR) relaxation studies are reported for three ionic liquids: 1-ethyl-3- methylimidazolium thiocyanate (EMIM-SCN, 220–258 K), 1-butyl-3-methylimidazolium tetrafluoroborate (BMIM-BF{sub 4}, 243–318 K), and 1-butyl-3-methylimidazolium hexafluorophosphate (BMIM-PF{sub 6}, 258–323 K). The dispersion of {sup 1}H spin-lattice relaxation rate R{sub 1}(ω) is measured in the frequency range of 10 kHz–20 MHz, and the studies are complemented by {sup 19}F spin-lattice relaxation measurements on BMIM-PF{sub 6} in the corresponding frequency range. From the {sup 1}H relaxation results self-diffusion coefficients for the cation in EMIM-SCN, BMIM-BF{sub 4}, and BMIM-PF{sub 6} are determined. This is done by performing an analysis considering all relevant intra- and intermolecular relaxation contributions to the {sup 1}H spin-lattice relaxation as well as by benefiting from the universal low-frequency dispersion law characteristic of Fickian diffusion which yields, at low frequencies, a linear dependence of R{sub 1} on square root of frequency. From the {sup 19}F relaxation both anion and cation diffusion coefficients are determined for BMIM-PF{sub 6}. The diffusion coefficients obtained from FC NMR relaxometry are in good agreement with results reported from pulsed- field-gradient NMR. This shows that NMR relaxometry can be considered as an alternative route of determining diffusion coefficients of both cations and anions in ionic liquids.

  18. Saturation properties of 1-alkyl-3-methylimidazolium based ionic liquids.

    PubMed

    Rane, Kaustubh S; Errington, Jeffrey R

    2014-07-24

    We study the liquid-vapor saturation properties of room temperature ionic liquids (RTILs) belonging to the homologous series 1-alkyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([Cnmim][NTf2]) using Monte Carlo simulation. We examine the effect of temperature and cation alkyl chain length n on the saturated densities, vapor pressures, and enthalpies of vaporization. These properties are explicitly calculated for temperatures spanning from 280 to 1000 K for RTILs with n = 2, 4, 6, 8, 10, and 12. We also explore how the identity of the anion influences saturation properties. Specifically, we compare results for [C(4)mim][NTf2] with those for 1-butyl-3-methylimidazolium tetrafluoroborate ([C(4)mim][BF4]) and 1-butyl-3-methylimidazolium hexafluorophosphate ([C(4)mim][PF6]). Simulations are completed with a recently developed realistic united-atom force field. A combination of direct grand canonical and isothermal-isobaric temperature expanded ensemble simulations are used to construct phase diagrams. Our results are compared with experimental data and Gibbs ensemble simulation data. Overall, we find good agreement between our results and those measured experimentally. We find that the vapor pressures and enthalpies of vaporization show a strong dependence on the size of the alkyl chain at low temperatures, whereas no particular trend is observed at high temperatures. Finally, we also discuss the effect of temperature on liquid phase nanodomains observed in RTILs with large hydrophobic groups. We do not observe a drastic change in liquid phase structure upon variation of the temperature, which suggests there is not a sharp phase transition between a nanostructured and homogeneous liquid, as has been suggested in earlier studies. PMID:24986360

  19. The importance of ion size and electrode curvature on electrical double layers in ionic liquids

    SciTech Connect

    Feng, G.; Qiao, R.; Huang, J; Dai, S.; Sumpter, B. G.; Meunier, V.

    2011-01-01

    Room-temperature ionic liquids (ILs) are an emerging class of electrolytes for supercapacitors. We investigate the effects of ion size and electrode curvature on the electrical double layers (EDLs) in two ILs 1-butyl-3-methylimidazolium chloride [BMIM][Cl] and 1-butyl-3-methylimidazolium hexafluorophosphate [BMIM][PF{sub 6}], using a combination of molecular dynamics (MD) and quantum density functional theory (DFT) simulations. The sizes of the counter-ion and co-ion affect the ion distribution and orientational structure of EDLs. The EDL capacitances near both planar and cylindrical electrodes were found to follow the order: [BMIM][Cl] (near the positive electrode) > [BMIM][PF{sub 6}] (near the positive electrode) ≈ [BMIM][Cl] (near the negative electrode) ≈ [BMIM][PF{sub 6}] (near the negative electrode). The EDL capacitance was also found to increase as the electrode curvature increases. These capacitance data can be fit to the Helmholtz model and the recently proposed exohedral electrical double-cylinder capacitor (xEDCC) model when the EDL thickness is properly parameterized, even though key features of the EDLs in ILs are not accounted for in these models. To remedy the shortcomings of existing models, we propose a “Multiple Ion Layers with Overscreening” (MILO) model for the EDLs in ILs that takes into account two critical features of such EDLs, i.e., alternating layering of counter-ions and co-ions and charge overscreening. The capacitance computed from the MILO model agrees well with the MD prediction. Although some input parameters of the MILO model must be obtained from MD simulations, the MILO model may provide a new framework for understanding many important aspects of EDLs in ILs (e.g., the variation of EDL capacitance with the electrode potential) that are difficult to interpret using classical EDL models and experiments.

  20. The Importance of Ion Size and Electrode Curvature on Electrical Double Layers in Ionic Liquids

    SciTech Connect

    Feng, Guang; Qiao, Rui; Huang, Jingsong; Dai, Sheng; Sumpter, Bobby G; Meunier, Vincent

    2010-01-01

    Room-temperature ionic liquids (ILs) are an emerging class of electrolytes for supercapacitors. We investigate the effects of ion size and electrode curvature on the electrical double layers (EDLs) in two ILs 1-butyl-3-methylimidazolium chloride [BMIM][Cl] and 1-butyl-3-methylimidazolium hexafluorophosphate [BMIM][PF(6)], using a combination of molecular dynamics (MD) and quantum density functional theory (DFT) simulations. The sizes of the counter-ion and co-ion affect the ion distribution and orientational structure of EDLs. The EDL capacitances near both planar and cylindrical electrodes were found to follow the order: [BMIM][Cl] (near the positive electrode) > [BMIM][PF(6)] (near the positive electrode) {approx} [BMIM][Cl] (near the negative electrode) {approx} [BMIM][PF(6)] (near the negative electrode). The EDL capacitance was also found to increase as the electrode curvature increases. These capacitance data can be fit to the Helmholtz model and the recently proposed exohedral electrical double-cylinder capacitor (xEDCC) model when the EDL thickness is properly parameterized, even though key features of the EDLs in ILs are not accounted for in these models. To remedy the shortcomings of existing models, we propose a 'Multiple Ion Layers with Overscreening' (MILO) model for the EDLs in ILs that takes into account two critical features of such EDLs, i.e., alternating layering of counter-ions and co-ions and charge overscreening. The capacitance computed from the MILO model agrees well with the MD prediction. Although some input parameters of the MILO model must be obtained from MD simulations, the MILO model may provide a new framework for understanding many important aspects of EDLs in ILs (e.g., the variation of EDL capacitance with the electrode potential) that are difficult to interpret using classical EDL models and experiments.

  1. Dispersive liquid-liquid microextraction of silver nanoparticles in water using ionic liquid 1-octyl-3-methylimidazolium hexafluorophosphate.

    PubMed

    Chen, Sha; Sun, Yuanjing; Chao, Jingbo; Cheng, Liping; Chen, Yun; Liu, Jingfu

    2016-03-01

    Using the ionic liquid (IL) 1-octyl-3-methylimidazolium hexafluorophosphate as the extractant and methanol as the dispersion solvent, a dispersive liquid-liquid microextraction method was developed to extract silver nanoparticles (AgNPs) from environmental water samples. Parameters that influenced the extraction efficiency such as IL concentration, pH and extraction time were optimized. Under the optimized conditions, the highest extraction efficiency for AgNPs was above 90% with an enrichment factor of >90. The extracted AgNPs in the IL phase were identified by transmission electron microscopy and ultraviolet-visible spectroscopy, and quantified by inductively coupled plasma mass spectrometry after microwave digestion, with a detection limit of 0.01μg/L. The spiked recovery of AgNPs was 84.4% with a relative standard deviation (RSD) of 3.8% (n=6) at a spiked level of 5μg/L, and 89.7% with a RSD of 2.2% (n=6) at a spiked level of 300μg/L, respectively. Commonly existed environmental ions had a very limited influence on the extraction efficiency. The developed method was successfully applied to the analysis of AgNPs in river water, lake water, and the influent and effluent of a wastewater treatment plant, with recoveries in the range of 71.0%-90.9% at spiking levels of 0.11-4.7μg/L. PMID:26969067

  2. Madelung energy and theoretical zero-field splittings of (2:1) tetramethyltetraselenafulvalenium hexafluorophosphate ((TMTSF)/sub 2/PF/sub 6/)

    SciTech Connect

    Metzger, R.M.

    1981-07-01

    The Madelung energy of the organic superconductor (2:1) tetramethylselenafulvalenium hexafluorophosphate ((TMTSF)/sub 2/PF/sub 6/) is -236.5798 kJ/mol (-237.3152 kJ/mol if the PF/sub 6//sup -/ ion rotates freely). Its theoretical fine-structure splitting parameters are D = 0.014 288 cm/sup -1/ and E = -0.000 557 cm/sup -1/ (nearest-neighbor (TMTSF/sup +/)/sub 2/ dimer).(AIP)

  3. Reactions of Starch in Ionic Liquids

    Technology Transfer Automated Retrieval System (TEKTRAN)

    We found that starches are found to be soluble at 80 ºC in ionic liquids such as 1-butyl-3-methylimidazolium chloride (BMIMCl) and 1-butyl-3-methylimidazolium dicyanamide (BMIMdca) in concentration up to 10% (w/w). Higher concentrations of biopolymers in these novel solvents resulted in solutions w...

  4. Studies on structural, thermal and AC conductivity scaling of PEO-LiPF6 polymer electrolyte with added ionic liquid [BMIMPF6

    NASA Astrophysics Data System (ADS)

    Chaurasia, S. K.; Saroj, A. L.; Shalu, Singh, V. K.; Tripathi, A. K.; Gupta, A. K.; Verma, Y. L.; Singh, R. K.

    2015-07-01

    Preparation and characterization of polymer electrolyte films of PEO+10wt.% LiPF6 + xwt.% BMIMPF6 (1-butyl-3-methylimidazolium hexafluorophosphate) containing dopant salt lithium hexafluorophosphate (LiPF6) and ionic liquid (BMIMPF6) having common anion PF6 - are reported. The ionic conductivity of the polymer electrolyte films has been found to increase with increasing concentration of BMIMPF6 in PEO+10 wt.% LiPF6 due to the plasticization effect of ionic liquid. DSC and XRD results show that the crystallinity of polymer electrolyte decreases with BMIMPF6 concentration which, in turn, is responsible for the increase in ionic conductivity. FTIR spectroscopic study shows the complexation of salt and/or ionic liquid cations with the polymer backbone. Ion dynamics behavior of PEO+LiPF6 as well as PEO+LiPF6 + BMIMPF6 polymer electrolytes was studied by frequency dependent conductivity, σ(f) measurements. The values σ(f) at various temperatures have been analyzed in terms of Jonscher power law (JPL) and scaled with respect to frequency which shows universal power law characteristics at all temperatures.

  5. Ion chromatography electrospray ionization mass spectrometry method development and investigation of lithium hexafluorophosphate-based organic electrolytes and their thermal decomposition products.

    PubMed

    Kraft, Vadim; Grützke, Martin; Weber, Waldemar; Winter, Martin; Nowak, Sascha

    2014-08-01

    A method based on the coupling of ion chromatography (IC) and electrospray ionization mass spectrometry (ESI-MS) for the separation and determination of thermal decomposition products of LiPF6-based organic electrolytes is presented. The utilized electrolytes, LP30 and LP50, are commercially available and consist of 1mol/l LiPF6 dissolved in ethylene carbonate/dimethyl carbonate and ethylene carbonate/ethyl methyl carbonate, respectively. For the separation method development three ion chromatographic columns with different capacity and stationary phase were used and compared. Besides the known hydrolysis products of lithium hexafluorophosphate, several new organophosphates were separated and identified with the developed IC-ESI-MS method during aging investigations of the electrolytes. The chemical structures were elucidated with IC-ESI-MS/MS. PMID:24939088

  6. A non-aqueous all-cobalt redox flow battery using 1,10-phenanthrolinecobalt(II) hexafluorophosphate as active species

    NASA Astrophysics Data System (ADS)

    Xing, Xueqi; Zhang, Dapeng; Li, Yongdan

    2015-04-01

    A non-aqueous all-cobalt redox flow battery, with a cobalt complex 1,10-phenanthrolinecobalt(II) hexafluorophosphate ([Co(phen)3](PF6)2) as the active species, acetonitrile as the solvent and tetraethylammonium hexafluorophosphate (TEAPF6) as the supporting electrolyte, has been investigated. The electrochemical behaviour of oxidation and reduction reactions is measured using cyclic voltammetry (CV). The [Co(phen)3]2+ can be oxidized to [Co(phen)3]3+ and reduced to [Co(phen)3]+. A theoretical cell potential of 1.45 V for one-electron disproportionation reaction is obtained. The electrode reactions show quasi-reversible behaviour and are diffusion controlled. The diffusion coefficients of [Co(phen)3] 2+ for oxidation and reduction reactions are calculated to be 1.35-2.34 × 10-6 cm2 s-1 and 2.50-4.35 × 10-6 cm2 s-1, respectively. The effect of the electrode material is also examined by experiments. The CV curves of [Co(phen)3]2+ on the graphite working electrode show superior peak current and diffusivity to those measured on the glassy-carbon electrode. The charge-discharge performance of the battery is accessed with an H-type glass cell. A coulomb efficiency of about 52% is achieved at 50% state-of-charge for an electrolyte containing of 0.01 M [Co(phen)3]2+ and 0.5 M TEAPF6 in acetonitrile.

  7. Rapid and simultaneous determination of tetrafluoroborate, thiocyanate and hexafluorophosphate by high-performance liquid chromatography using a monolithic column and direct conductivity detection.

    PubMed

    Yang, Ling; Yu, Hong; Wang, Yaqin

    2010-01-01

    A method was developed for fast and simultaneous determination of tetrafluoroborate (BF(4)(-)), thiocyanate (SCN(-)) and hexafluorophosphate (PF(6)(-)) by high-performance liquid chromatography using a silica-based monolithic column and direct (non-suppressed) conductivity detection. Chromatographic separation was performed on a Chromolith Speed ROD RP-18e column with tetrabutylammonium hydroxide (TBA) + citric acid + acetonitrile as eluent. The effects of the types of eluent, TBA concentration, acetonitrile volume fraction, eluent pH, column temperature and flow rate on the retention of anions were investigated. The optimized chromatographic conditions were selected. Under the optimal conditions, the baseline separation of BF(4)(-), SCN(-) and PF(6)(-) was achieved without any interference by other anions (F(-), Cl(-), Br(-), I(-), NO(3)(-), ClO(3)(-) and SO(4)(2-)). The detection limit (S/N = 3) was 0.42, 0.46 and 1.42 mg L(-1) for BF(4)(-), SCN(-) and PF(6)(-), respectively. The present method was successfully applied to the determination of BF(4)(-), SCN(-) and PF(6)(-) in ionic liquids. PMID:20702939

  8. 4-Amino-1-(3-mercapto-propyl)-pyridine hexafluorophosphate ionic liquid functionalized gold nanoparticles for IgG immunosensing enhancement.

    PubMed

    Li, Rui; Wu, Kangbing; Liu, Changxian; Huang, Yin; Wang, Yanying; Fang, Huaifang; Zhang, Huijuan; Li, Chunya

    2014-06-01

    A novel ionic liquid, 4-amino-1-(3-mercapto-propyl)-pyridine hexafluorophosphate (AMPPH), was successfully synthesized and characterized. Subsequently, AMPPH was used as a functional monomer to fabricate AMPPH-modified gold nanoparticles (AMPPH-AuNPs) via a one-pot synthesis method. The as-prepared AMPPH-AuNPs were confirmed with transmission electron microscopy and X-ray photoelectron spectroscopy. AMPPH-AuNPs were used to construct a biocompatible interface to immobilize rabbit anti-human IgG (anti-HIgG) onto a glassy carbon electrode (GCE) surface, followed by a cross-linking step with glutaraldehyde to fabricate an anti-HIgG-AMPPH-AuNPs/GCE. The nonspecific binding sites were enclosed with bovine serum albumin (BSA) to develop an immunosensor for human IgG. Electrochemical impedance spectroscopy, cyclic voltammetry and differential pulse voltammetry were used to investigate the electrochemical properties of the developed immunosensor. The results indicate that AMPPH-AuNPs can improve the immunosensing performance. The current response of the immunosensor was found linearly related to human IgG concentration in the range of 0.1-5.0 ng mL(-1) and 5.0-100.0 ng mL(-1). The detection limit is estimated to be 0.08 ng mL(-1) (S/N = 3). The obtained immunosensor was successfully applied to the analysis human IgG immunoglobulin in human serum, and the results were well consistent with ELISA method. PMID:24803006

  9. Bucky-gel coated glassy carbon electrodes, for voltammetric detection of femtomolar leveled lead ions.

    PubMed

    Wan, Qijin; Yu, Fen; Zhu, Lina; Wang, Xiaoxia; Yang, Nianjun

    2010-10-15

    Femtomolar (fM) leveled lead ions were electrochemically detected using a bucky-gel coated glassy carbon electrode and differential pulse anodic stripping voltammetry. The bucky-gel was composed of dithizone, ionic liquid (1-butyl-3-methylimidazolium hexafluorophosphate), and multi-walled carbon nanotubes (MWCNTs). The fabrication of the bucky-gel coated electrode was optimized. The modified electrode was characterized with voltammetry, electrochemical impedance spectroscopy, and chronoamperometry. After the accumulation of lead ions into the bucky-gel modified electrode at -1.2V vs. saturated calomel electrode (SCE) for 5 min in a pH 4.4 sodium acetate-acetate acid buffer solution, differential pulse anodic stripping voltammograms of the accumulated lead show an anodic wave at -0.58 V. The anodic peak current is detectable for lead ions in the concentration range from 1.0 μM down to 500 fM. The detection limit is calculated to be 100 fM. The proposed method was successfully applied for the detection of lead ions in lake water. PMID:20875583

  10. Photoreversible gelation of a triblock copolymer in an ionic liquid.

    PubMed

    Ueki, Takeshi; Nakamura, Yutaro; Usui, Ryoji; Kitazawa, Yuzo; So, Soonyong; Lodge, Timothy P; Watanabe, Masayoshi

    2015-03-01

    The reversible micellization and sol-gel transition of block copolymer solutions in an ionic liquid (IL) triggered by a photostimulus is described. The ABA triblock copolymer employed, denoted P(AzoMA-r-NIPAm)-b-PEO-b-P(AzoMA-r-NIPAm)), has a B block composed of an IL-soluble poly(ethylene oxide) (PEO). The A block consists of a random copolymer including thermosensitive N-isopropylacrylamide (NIPAm) units and a methacrylate with an azobenzene chromophore in the side chain (AzoMA). A phototriggered reversible unimer-to-micelle transition of a dilute ABA triblock copolymer (1 wt%) was observed in an IL, 1-butyl-3-methylimidazolium hexafluorophosphate ([C4mim]PF6), at an intermediate "bistable" temperature (50 °C). The system underwent a reversible sol-gel transition cycle at the bistable temperature (53 °C), with reversible association/fragmentation of the polymer network resulting from the phototriggered self-assembly of the ABA triblock copolymer (20 wt%) in [C4 mim]PF6. PMID:25613353

  11. Molecular dynamics studies on the adaptability of an ionic liquid in the extraction of solid nanoparticles.

    PubMed

    Frost, Denzil S; Machas, Michael; Dai, Lenore L

    2012-10-01

    Recently, a number of publications have suggested that ionic liquids (ILs) can absorb solid particles. This development may have implications in fields like oil sand processing, oil spill beach cleanup, and water treatment. In this Article, we provide a computational investigation of this phenomenon via molecular dynamics simulations. Two particle surface chemistries were investigated: (1) hydrocarbon-saturated and (2) silanol-saturated, representing hydrophobic and hydrophilic particles, respectively. Employing 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF(6)]) as a model IL, these nanoparticles were allowed to equilibrate at the IL/water and IL/hexane interfaces to observe the interfacial self-assembled structures. At the IL/water interface, the hydrocarbon-based nanoparticles were nearly completely absorbed by the IL, while the silica nanoparticles maintained equal volume in both phases. At the IL/hexane interface, the hydrocarbon nanoparticles maintained minimal interactions with the IL, whereas the silica nanoparticles were nearly completely absorbed by it. Studies of these two types of nanoparticles immersed in the bulk IL indicate that the surface chemistry has a great effect on the corresponding IL liquid structure. These effects include layering of the ions, hydrogen bonding, and irreversible absorption of some ions to the silica nanoparticle surface. We quantify these effects with respect to each nanoparticle. The results suggest that ILs likely exhibit this absorption capability because they can form solvation layers with reduced dynamics around the nanoparticles. PMID:22950605

  12. High-performance lubricant additives based on modified graphene oxide by ionic liquids.

    PubMed

    Fan, Xiaoqiang; Wang, Liping

    2015-08-15

    Graphene oxide (GO) is a layered material bearing a variety of oxygen-containing functional groups on its basal planes and edges, which allow it as a substrate to conduct a variety of chemical transformations. Here modified graphene oxide (MGO) was prepared using alkyl imidazolium ionic liquids (ILs) (1-butyl-3-methylimidazolium tetrafluoroborate (LB104), 1-butyl-3-methyl imidazolium hexafluorophosphate (LP104) and 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl) amide (LF106)) via epoxide ring-opening reaction, cation-π stacking or van der Waals interactions, with LB104 modified graphene (MG) exfoliated from graphite rod by a moderate electrochemical method as a comparison. The stability and tribological properties of MGO and MG as multialkylated cyclopentanes (MACs) additives were investigated in detail. The results show that GO is converted into graphene through the chemical modification using ILs, and MGO with good dispersion and stability in MACs significantly improves the tribological performance (friction and wear were reduced about 27% and 74% with pure MACs as a comparison, respectively). The excellent tribological properties are attributed to the formation of an ILs-containing graphene-rich tribofilm on the sliding surfaces, which as the third body can prevent the sliding surfaces from straight asperity contact and improve friction reducing and anti-wear behaviors. PMID:25935280

  13. Determination of water in room temperature ionic liquids by cathodic stripping voltammetry at a gold electrode.

    PubMed

    Zhao, Chuan; Bond, Alan M; Lu, Xunyu

    2012-03-20

    An electrochemical method based on cathodic stripping voltammetry at a gold electrode has been developed for the determination of water in ionic liquids. The technique has been applied to two aprotic ionic liquids, (1-butyl-3-ethylimidazolium tetrafluoroborate and 1-butyl-3-methylimidazolium hexafluorophosphate), and two protic ionic liquids, (bis(2-hydroxyethyl)ammonium acetate and triethylammonium acetate). When water is present in an ionic liquid, electrooxidation of a gold electrode forms gold oxides. Thus, application of an anodic potential scan or holding the potential of the electrode at a very positive value leads to accumulation of an oxide film. On applying a cathodic potential scan, a sensitive stripping peak is produced as a result of the reduction of gold oxide back to gold. The magnitude of the peak current generated from the stripping process is a function of the water concentration in an ionic liquid. The method requires no addition of reagents and can be used for the sensitive and in situ determination of water present in small volumes of ionic liquids. Importantly, the method allows the determination of water in the carboxylic acid-based ionic liquids, such as acetate-based protic ionic liquids, where the widely used Karl Fischer titration method suffering from an esterification side reaction which generates water as a side product. PMID:22372467

  14. Synthesis of Mesoporous Carbons from Rice Husk for Supercapacitors with High Energy Density in Ionic Liquid Electrolytes.

    PubMed

    He, Xiaojun; Zhang, Hebao; Xie, Kang; Xia, Youyi; Zhao, Zhigang; Wang, Xiaoting

    2016-03-01

    High-performance mesoporous carbons (MCs) for supercapacitors were made from rice husk by one-step microwave-assisted ZnCl2 activation. The microstructures of MCs as-made were characterized by field emission scanning electron microscopy and transmission electron microscopy. The pore structure parameters of MCs were obtained by N2 adsorption technique. The electrochemical properties of MC electrodes were studied by constant current charge-discharge, cyclic voltammetry and electrochemical impedance spectroscopy in different electrolytes. The results showed that the specific surface area of MC4 made at the ZnCl2/rice husk mass of 4:1 reached 1737 m2 g(-1). The specific capacitance and energy density of the electrodes fabricated from the mixture of MC4 and microporous carbon increased with the mass percentage of MC4, reaching 157 F g(-1) and 84 Wh kg(-1) at 0.05 A g(-1), and showed good cycle stability in 1-butyl-3-methylimidazolium hexafluorophosphate electrolyte. Compared to the often-used aqueous and organic electrolytes, MC4 capacitor exhibited extremely high energy density in ionic liquid electrolyte, remaining at 28 Wh kg(-1) at 1684 W kg(-1). This work paves a new way to produce cost-effective MCs from biomass for supercapacitors with extremely high energy density in ionic liquid electrolytes. PMID:27455718

  15. Preconcentration and determination of lead and cadmium levels in blood samples of adolescent workers consuming smokeless tobacco products in Pakistan.

    PubMed

    Arain, Sadaf Sadia; Kazi, Tasneem Gul; Afridi, Hassan Imran; Brahman, Kapil Dev; Naeemullah; Khan, Sumaira; Panhwar, Abdul Haleem; Kamboh, Muhammad Afzal; Memon, Jamil R

    2015-05-01

    The present study was aimed to evaluate the cadmium (Cd) and lead (Pb) levels in the blood samples of adolescent boys, chewing different smokeless tobacco (SLT) products in Pakistan. For comparative purpose, boys of the same age group (12-15 years), not consumed any SLT products were selected as referents. To determine trace levels of Cd and Pb in blood samples, a preconcentration method, vortex-assisted liquid-liquid microextraction (VLLME) has been developed, prior to analysis by flame atomic absorption spectrometry. The hydrophobic chelates of Cd and Pb with ammonium pyrrolidinedithiocarbamate were extracted into the fine droplets of ionic liquid (IL) 1-butyl-3-methylimidazolium hexafluorophosphate, while nonionic surfactant, Triton X-114 was used as a dispersing medium. The main factors affecting the recoveries of Cd and Pb, such as concentration of APDC, centrifugation time, volume of IL and TX-114, were investigated in detail. It was also observed that adolescent boys who consumed different SLT products have 2- to 3-fold higher levels of Cd and Pb in their blood samples as compared to referent boys (p < 0.001). PMID:25930204

  16. Comparative ecotoxicology study of two neoteric solvents: Imidazolium ionic liquid vs. glycerol derivative.

    PubMed

    Perales, Eduardo; García, Cristina Belén; Lomba, Laura; Aldea, Luis; García, José Ignacio; Giner, Beatriz

    2016-10-01

    In this study we have compared the acute ecotoxicity of two solvents, with very different structure and origin, but sharing many physical-chemical properties, so they can be used for similar purposes; a well-known ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF6]) and a solvent partially derived from biomass, 3-bis(2,2,2-trifluoroethoxy)propan-2-ol (BTFIP). We have used three biomodels (Vibrio fischeri, Daphnia magna and Danio rerio) and performed the comparison applying the Environmental, Health and Safety (EHS) hazard assessment. According to the results, ecotoxicity of [BMIM][PF6] and BTFIP is quite similar in the simplest model Vibrio fischeri, while in Daphnia magna [BMIM][PF6] is clearly more toxic. However, in Danio rerio, toxicity of these chemicals is again quite similar and both can be classified as "nontoxic". The higher index value of [BMIM][PF6] in water mediate effect in the EHS assessment indicates that this ionic liquid is more dangerous than BTFIP, although accumulation and degradation properties have not been taken into account. Further studies will be necessary to ascertain these conclusions. PMID:27265564

  17. On the structural stability of ionic liquid-IRMOF composites: a computational study.

    PubMed

    Abroshan, Hadi; Kim, Hyung J

    2015-03-01

    The structural stability of isoreticular metal organic frameworks, IRMOF-1 and IRMOF-10, confining ionic liquids (ILs) inside their nano-porous cavities is studied via molecular dynamics (MD) simulations. Imidazolium- and pyridinium-based ILs, including BMI(+)PF6(-), BMI(+)Br(-), BMI(+)Tf2N(-), BMI(+)DCA(-), and BuPy(+)Tf2N(-) (BMI(+) = 1-butyl-3-methylimidazolium, PF6(-) = hexafluorophosphate, Br(-) = bromide, Tf2N(-) = bis(trifluoromethylsulfonyl)imide, DCA(-) = dicyanamide, and BuPy(+) = N-butylpyridinium), at different loadings are considered. It is found that both IRMOFs are structurally unstable and deform dramatically from their crystal structure in the presence of ILs. The interactions between the metallic parts of IRMOFs and IL anions play a major role in structural disruption and collapse of these MOFs. Thus elongated anions such as Tf2N(-) and DCA(-) that can interact with two different metal sites tend to lower IRMOF stability compared to spherical anions such as Br(-) and PF6(-). A further analysis via density functional theory (DFT) and ab initio molecular dynamics (AIMD) simulations lends support to the MD results regarding structural instability of IRMOFs in the presence of ILs. PMID:25649989

  18. Syntheses and crystal structures of benzene-sulfonate and -carboxylate copper polymers and their application in the oxidation of cyclohexane in ionic liquid under mild conditions.

    PubMed

    Hazra, Susanta; Ribeiro, Ana P C; Guedes da Silva, M Fátima C; Nieto de Castro, Carlos A; Pombeiro, Armando J L

    2016-09-21

    The syntheses, crystal structures and catalytic activities of the polymers derived from 2-(2-pyridylmethyleneamino)benzenesulfonic acid (HL), viz. [CuL(H2tma)]n (1) and [{Cu2L2(H2pma)}·(8H2O)]n (2) [H3tma = benzene-1,3,5-tricarboxylic (trimesic) acid and H4pma = benzene-1,2,4,5-tetracarboxylic (pyromellitic) acid], are presented. Despite the comparable combinations and compositions of ligands (sulfonate and carboxylate) in these two polymers the bridging moiety in 1 is sulfonate while in 2 it is carboxylate. Complexes 1 and 2 act as catalysts in the peroxidative oxidation of cyclohexane under mild conditions using either the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate [bmim][PF6] or acetonitrile as the solvent. The ionic liquid medium leads to increases in the yields and in the turnover numbers, achieved in shorter reaction times in comparison with those when using the conventional acetonitrile solvent. A simple recycling of the catalysts in the ionic liquid medium is achieved without loss of activity and selectivity. PMID:27529408

  19. Interactions of Ionic Liquids with Uranium and its Bioreduction

    SciTech Connect

    Zhang, C.; Francis, A.

    2012-09-18

    We investigated the influence of ionic liquids (ILs) 1-butyl-3-methylimidazolium hexafluorophosphate [BMIM]{sup +}[PF{sub 6}]{sup -}, N-ethylpyridinium trifluoroacetate [EtPy]{sup +}[CF{sub 3}COO]{sup -} and N-ethylpyridinium tetrafluoroborate [Et-Py]{sup +}[BF{sub 4}]{sup -} on uranium reduction by Clostridium sp. under anaerobic conditions. Potentiometric titration, UV-vis spectrophotometry, LC-MS and EXAFS analyses showed monodentate complexation between uranyl and BF{sub 4}{sup -} PF{sub 6}{sup -}; and bidentate complexation with CF{sub 3}COO{sup -}. Ionic liquids affected the growth of Clostridium sp. as evidenced by decrease in optical density, changes in pH, gas production, and the extent of U(VI) reduction and precipitation of U(IV) from solution. Reduction of U(VI) to U(IV) was observed in the presence of [EtPy][BF{sub 4}] and [BMIM][PF{sub 6}] but not with [EtPy][CF{sub 3}COO].

  20. MD Study of Stokes Shifts in Ionic Liquids: Temperature Dependence.

    PubMed

    Wu, Eric C; Kim, Hyung J

    2016-05-26

    Effects of temperature on Stokes shifts, solvation structure, and dynamics in ionic liquids EMI(+)Tf2N(-), EMI(+)PF6(-), and BMI(+)PF6(-) (EMI(+) = 1-ethyl-3-methylimidazolium, BMI(+) = 1-butyl-3-methylimidazolium, Tf2N(-) = bis(trifluoromethylsulfonyl)imide, and PF6(-) = hexafluorophosphate) are investigated via molecular dynamics (MD) computer simulations in the temperature range 350 K ≤ T ≤ 500 K. Two different types of solutes are considered: a simple model diatomic solute and realistic coumarin 153, both of which are characterized by more polar S1 and less polar S0 states. In all three ionic liquids studied, the Stokes shift tends to decrease with increasing temperature. For coumarin 153, as T increases, the Franck-Condon energy for steady-state absorption decreases, whereas that for steady-state emission increases. Our findings indicate that the effective polarity of ionic liquids decreases as T increases. Their solvation dynamics are characterized by an ultrafast initial decay in the subpicosecond time scale, followed by slow dissipative relaxation, regardless of temperature. For both solutes, the solvent frequency that quantifies initial ultrafast dynamics shows little temperature dependence. By contrast, the long-time dissipative dynamics become significantly faster with rising T. Variations of solvation structure with temperature and their connection to Stokes shift and solvation dynamics are briefly examined. PMID:27133895

  1. Temperature-controlled ionic liquid-based ultrasound-assisted microextraction for preconcentration of trace quantity of cadmium and nickel by using organic ligand in artificial saliva extract of smokeless tobacco products

    NASA Astrophysics Data System (ADS)

    Arain, Sadaf Sadia; Kazi, Tasneem Gul; Arain, Asma Jabeen; Afridi, Hassan Imran; Baig, Jameel Ahmed; Brahman, Kapil Dev; Naeemullah; Arain, Salma Aslam

    2015-03-01

    A new approach was developed for the preconcentration of cadmium (Cd) and nickel (Ni) in artificial saliva extract of dry snuff (brown and black) products using temperature-controlled ionic liquid-based ultrasound-assisted dispersive liquid-liquid microextraction (TIL-UDLLμE) followed by electrothermal atomic absorption spectrometry (ETAAS). The Cd and Ni were complexed with ammonium pyrrolidinedithiocarbamate (APDC), extracted in ionic liquid drops, 1-butyl-3-methylimidazolium hexafluorophosphate [C4MIM][PF6]. The multivariate strategy was applied to estimate the optimum values of experimental variables influence the % recovery of analytes by TIL-UDLLμE method. At optimum experimental conditions, the limit of detection (3s) were 0.05 and 0.14 μg L-1 while relative standard deviations (% RSD) were 3.97 and 3.55 for Cd and Ni respectively. After extraction, the enhancement factors (EF) were 87 and 79 for Cd and Ni, respectively. The RSD for six replicates of 10 μg L-1 Cd and Ni were 3.97% and 3.55% respectively. To validate the proposed method, certified reference material (CRM) of Virginia tobacco leaves was analyzed, and the determined values of Cd and Ni were in good agreement with the certified values. The concentration of Cd and Ni in artificial saliva extracts corresponds to 39-52% and 21-32%, respectively, of the total contents of both elements in dry brown and black snuff products.

  2. (R)-PAC biosynthesis in [BMIM][PF₆]/aqueous biphasic system using Saccharomyces cerevisiae BY4741 cells.

    PubMed

    Kandar, Smita; Suresh, A K; Noronha, Santosh B

    2015-02-01

    (R)-phenylacetylcarbinol or (R)-PAC is a pharmaceutical precursor of (1R, 2S) ephedrine and (1S, 2S) pseudoephedrine. Biotransformation of benzaldehyde and glucose by pyruvate decarboxylase produces (R)-PAC. This biotransformation suffers from toxicity of the substrate, product [(R)-PAC] and by-product (benzyl alcohol). In the present study, ionic liquid/aqueous biphasic system was employed to enhance (R)-PAC production. Fermented broth was the reaction medium in which Saccharomyces cerevisiae BY4741 was the source of pyruvate decarboxylase. Hydrophobic ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF6]) was the non-aqueous phase in which toxic compounds reside. Biocompatibility of [BMIM][PF6] and adequate distribution coefficients of benzaldehyde, (R)-PAC and benzyl alcohol were determined. A Box-Behnken design and response surface methodology were used for the optimization of biotransformation variables in order to maximize (R)-PAC yield and productivity. The results showed higher (R)-PAC yield and productivity of ∼1.5-fold each in the biphasic biotransformation of phase volume ratio 0.05 as compared to the monophasic (conventional) biotransformation. Moreover, the level of major by-product benzyl alcohol was also 3.5-fold lower in biphasic biotransformation. [BMIM][PF6]/aqueous biphasic system is a new approach which could intensify the (R)-PAC production. PMID:25424285

  3. Temperature-controlled ionic liquid-based ultrasound-assisted microextraction for preconcentration of trace quantity of cadmium and nickel by using organic ligand in artificial saliva extract of smokeless tobacco products.

    PubMed

    Arain, Sadaf Sadia; Kazi, Tasneem Gul; Arain, Asma Jabeen; Afridi, Hassan Imran; Baig, Jameel Ahmed; Brahman, Kapil Dev; Naeemullah; Arain, Salma Aslam

    2015-03-01

    A new approach was developed for the preconcentration of cadmium (Cd) and nickel (Ni) in artificial saliva extract of dry snuff (brown and black) products using temperature-controlled ionic liquid-based ultrasound-assisted dispersive liquid-liquid microextraction (TIL-UDLLμE) followed by electrothermal atomic absorption spectrometry (ETAAS). The Cd and Ni were complexed with ammonium pyrrolidinedithiocarbamate (APDC), extracted in ionic liquid drops, 1-butyl-3-methylimidazolium hexafluorophosphate [C4MIM][PF6]. The multivariate strategy was applied to estimate the optimum values of experimental variables influence the % recovery of analytes by TIL-UDLLμE method. At optimum experimental conditions, the limit of detection (3s) were 0.05 and 0.14μgL(-1) while relative standard deviations (% RSD) were 3.97 and 3.55 for Cd and Ni respectively. After extraction, the enhancement factors (EF) were 87 and 79 for Cd and Ni, respectively. The RSD for six replicates of 10μgL(-1) Cd and Ni were 3.97% and 3.55% respectively. To validate the proposed method, certified reference material (CRM) of Virginia tobacco leaves was analyzed, and the determined values of Cd and Ni were in good agreement with the certified values. The concentration of Cd and Ni in artificial saliva extracts corresponds to 39-52% and 21-32%, respectively, of the total contents of both elements in dry brown and black snuff products. PMID:25523044

  4. Ultra-trace determination of lead in water and food samples by using ionic liquid-based single drop microextraction-electrothermal atomic absorption spectrometry.

    PubMed

    Manzoori, Jamshid L; Amjadi, Mohammad; Abulhassani, Jafar

    2009-06-30

    An improved single drop microextraction procedure was developed for the preconcentration of lead prior to its determination by electrothermal atomic absorption spectrometry. Ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate [C4MIM][PF6], was used as an alternative to volatile organic solvents for extraction. Lead was complexed with ammonium pyrroldinedithiocarbamate (APDC) and extracted into a 7-microL ionic liquid drop. The extracted complex was directly injected into the graphite furnace. Several variables affecting microextraction efficiency and ETAAS signal, such as pyrolysis and atomization temperature, pH, APDC concentration, extraction time, drop volume and stirring rate were investigated and optimized. In the optimum experimental conditions, the limit of detection (3s) and the enhancement factor were 0.015 microg L(-1) and 76, respectively. The relative standard deviation (RSD) for five replicate determinations of 0.2 microg L(-1) Pb was 5.2%. The developed method was validated by the analysis of certified reference materials and applied successfully to the determination of lead in several real samples. PMID:19463561

  5. Ionic liquid-based single drop microextraction combined with electrothermal atomic absorption spectrometry for the determination of manganese in water samples.

    PubMed

    Manzoori, Jamshid L; Amjadi, Mohammad; Abulhassani, Jafar

    2009-02-15

    Room temperature ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate [C(4)MIM][PF(6)], was used as an alternative to volatile organic solvents in single drop microextraction-electrothermal atomic absorption spectrometry (SDME-ETAAS). Manganese was extracted from aqueous solution into a drop of the ionic liquid after complextaion with 1-(2-thiazolylazo)-2-naphthol (TAN) and the drop was directly injected into the graphite furnace. Several variables affecting microextraction efficiency and ETAAS signal, such as pyrolysis and atomization temperature, pH, TAN concentration, extraction time, drop volume and stirring rate were investigated and optimized. In the optimum experimental conditions, the limit of detection (3s) and the enhancement factor were 0.024 microg L(-1) and 30.3, respectively. The relative standard deviation (RSD) for five replicate determinations of 0.5 microg L(-1) Mn(II) was 5.5%. The developed method was validated by the analysis of a certified reference material (NIST SRM 1643e) and applied successfully to the determination of manganese in several natural water samples. PMID:19084676

  6. Ionic liquid-based dynamic liquid-phase microextraction: application to the determination of anti-inflammatory drugs in urine samples.

    PubMed

    Cruz-Vera, Marta; Lucena, Rafael; Cárdenas, Soledad; Valcárcel, Miguel

    2008-08-15

    Dynamic liquid-phase microextraction (dLPME) using an ionic liquid as acceptor phase is proposed for the determination of six non-steroidal anti-inflammatory drugs (NSAIDs) in human urine samples for the first time. The extraction is carried out in a simple and automatic flow configuration. The chemical affinity between the extractant (1-butyl-3-methylimidazolium hexafluorophosphate) and the analytes permits a selective isolation of the drugs from the sample matrix allowing also their preconcentration. The whole analytical method has been optimized taking into account all the chemical, physical and hydrodynamic variables. The proposed method is a valuable alternative for the analysis of these drugs in urine within the concentration range 0.1-10 microg mL(-1), allowing their determination at therapeutic and toxic levels. Limits of detection were in the range from 38 ng mL(-1) (indomethacin) to 70 ng mL(-1) (naproxen). The repeatability of the proposed method expressed as RSD (n=5) varied between 2.1% (flurbiprofen) and 3.8% (tolmetin). PMID:18632109

  7. Separation and pre-concentration of glucocorticoids in water samples by ionic liquid supported vortex-assisted synergic microextraction and HPLC determination.

    PubMed

    Qin, Hui; Li, Bi; Liu, Mou Sheng; Yang, Ya Ling

    2013-04-01

    We have developed a synergic microextraction procedure based on ionic liquid for the pre-concentration and determination of glucocorticoids in water samples. Using nonionic surfactant Triton X-100 (TX-100) as synergic reagent, 1-butyl-3-methylimidazolium hexa-fluorophosphate accomplished extraction rapidly without heating in water bath. One key property of ionic liquids that highlights their potential is their wide liquid temperature range. The improved extraction was named as ionic liquid supported vortex-assisted synergic microextraction. Compared with the traditional liquid-liquid extraction and cloud point extraction, ionic liquid supported vortex-assisted synergic microextraction was accomplished in 8 min with considerably high recovery. The proposed method greatly improved the sensitivity of HPLC for the determination of glucocorticoids. The results obtained indicated a good linearity with the correlation coefficient of 0.997 over the range of 0.6-300 ng/mL and high sensitivity with LODs of 4.11, 9.19, and 7.50 ng/mL for hydrocortisone butyrate, beclomethasone dipropionate, and nandrolone phenylpropionate, respectively. The RSD of the method was 1.57-1.81% (n = 6) with enrichment factor of 99.85, and good recovery (≥97.24%). The method was successfully applied to the determination of glucocorticoids in mineral water, water of Dianchi lake, and tap water samples. PMID:23418157

  8. Dielectric spectroscopy study on ionic liquid microemulsion composed of water, TX-100, and BmimPF6

    NASA Astrophysics Data System (ADS)

    Chen, Zhen; Nozaki, Ryusuke

    2012-06-01

    We report here a broadband dielectric spectroscopy study on an ionic liquid microemulsion (ILM) composed of water, Triton X-100 (TX-100), and 1-butyl-3-methylimidazolium hexafluorophosphate (bmimPF6). It is found that the phase behavior of this ILM can be easily identified by its dielectric response. The dielectric behavior of the ILM in the GHz range is consistent with that of TX-100/water mixtures with comparable water-to-TX-100 weight ratio. It consists of the relaxations due to ethylene oxide (EO) unit relaxation, hydration water dynamics, and/or free water dynamics. The water content dependence of the EO unit relaxation suggests that this relaxation involves dynamics of hydration water molecules. In the IL-in-water microemulsion phase, it is found that bmimPF6 molecules are preferentially dissolved in water when their concentration in water is lower than the solubility. An additional dielectric relaxation that is absent in the TX-100/water mixtures is observed in the frequency range of 107-108 Hz for this ILM. This low-frequency relaxation is found closely related to the bmimPF6 molecule and could be attributed to the hopping of its cations/anions between the anionic/cationic sites.

  9. Formation, characterization and enzyme activity in water-in-hydrophobic ionic liquid microemulsion stabilized by mixed cationic/nonionic surfactants.

    PubMed

    Sun, Yanwen; Yan, Keqian; Huang, Xirong

    2014-10-01

    The phase behavior of the pseudo ternary system 1-tetradecyl-3-methylimidazolium bromide ([C14mim]Br)/Triton X-100/H2O/1-butyl-3-methylimidazolium hexafluorophosphate ([Bmim]PF6) has been studied at 35°C. With the increase in the mole fraction of Triton X-100 in the mixed surfactants, the water solubilization capacity increases and the monophasic area enlarges. The H2O-in-[Bmim]PF6 (W/IL) microemulsion was identified via electrical conductivity measurement. The existence of bulk water in the W/IL microemulsion was demonstrated based on the change of the O-D vibration frequency with content of D2O added and confirmed using UV-vis technique with CoCl2 as probe. Laccase can be solubilized in the W/IL microemulsion and exhibits a catalytic activity. The interface of the W/IL microemulsion has an inhibitory effect on the expression of the laccase activity, and the inhibitory effect is varied with the molar ratio of the mixed surfactants. PMID:25016546

  10. Simultaneous determination of α-, β- and γ-asarone in Acorus tatarinowii by microemulsion electrokinetic chromatography with [BMIM]PF6 as oil phase.

    PubMed

    Wang, Ying; Li, Feng; Yang, Feng-Qing; Zuo, Hua-Li; Xia, Zhi-Ning

    2012-11-15

    In the present study, a rapid and repeatable microemulsion electrokinetic chromatography (MEEKC) method was developed for the simultaneous determination of three isomers (α-, β- and γ-asarone) in Acorus tatarinowii by using ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM]PF(6)) as oil phase. Experimental parameters including the microemulsion compositions (concentrations of surfactant, co-surfactant and oil phase), pH, concentration of borate buffer, capillary temperature and voltage were intensively investigated. Finally, the main compounds in the methanol extract of A. tatarinowii were well separated within 11 min using a running buffer composed of 40 mmol/L sodium dodecyl sulfonate (SDS), 2.0 mol/L n-propanol, 8 mmol/L [BMIM]PF(6) in 10 mmol/L borate buffer of pH 9.5. The developed method was applied to determine the contents of α-, β- and γ-asarone in A. tatarinowii from five different producing areas in China (Anhui, Hebei, Sichuan, Zhejiang and Chongqing). The results indicated that the contents of three asarones are quite different in the investigated A. tatarinowii samples. On the other hand, the MEEKC with ionic liquid as oil phase should be a promising method for the analysis of volatile components especially isomers in medicinal herbs. PMID:23158356

  11. The effect of ionic liquid hydrophobicity and solvent miscibility on pluronic amphiphile self-assembly.

    PubMed

    Sharma, Suraj Chandra; Atkin, Rob; Warr, Gregory G

    2013-11-21

    The phase behavior of the triblock copolymer, (EO)20(PO)70(EO)20 (P123), in the water-immiscible (hydrophobic) ionic liquids (ILs), 1-butyl-3-methylimidazolium hexafluorophosphate (bmimPF6), and tris(pentafluoroethyl)trifluorophosphate (bmimFAP), has been investigated, and its amphiphilic self-assembly examined using small-angle X-ray scattering. The results obtained are contrasted with those for P123 in water. Direct and water-swellable micellar, hexagonal, and lamellar phases of P123 are found in bmimPF6, which behaves like a polar solvent despite being water immiscible, but bmimFAP behaves as a truly hydrophobic solvent, forming only a lamellar phase over a narrow composition range. The miscibility of bmimPF6 and water is increased by P123 addition, and at sufficiently high P123 concentrations, a single lamellar phase forms in which bmimPF6 and water are miscible in all proportions. In contrast, the preferential solubilization of bmimPF6 by PEO chains and bmimFAP by PPO chains causes the nanosegregation of these miscible ILs in concentrated P123 solutions. This leads to the formation of a P123/bmimPF6/bmimFAP microemulsion where bmimPF6 is the polar solvent and bmimFAP is the non-polar solvent. PMID:24138343

  12. Evidence of water-in-ionic liquid microemulsion formation by nonionic surfactant Brij-35.

    PubMed

    Rai, Rewa; Pandey, Siddharth

    2014-09-01

    Brij-35, a common and popular nonionic surfactant, is shown to form water-in-ionic liquid (w/IL) microemulsions with IL 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF6]) as the bulk phase. The presence of w/[bmim][PF6] microemulsions is hinted by the significantly increased solubility of water in Brij-35 solution of [bmim][PF6]. The formation of w/[bmim][PF6] microemulsions by Brij-35 is confirmed using dynamic light scattering (DLS) and small-angle X-ray scattering (SAXS) measurements. Brij-35 forms reverse micelle-type aggregates within [bmim][PF6] in the absence of added-water. These reverse micelles become w/[bmim][PF6] microemulsions as the water is added to the system. As the water loading (w0) is increased, the average diameter of the aggregates increases. Fourier transform infrared (FTIR) absorbance data reveal the presence of both "bound" and "free" water within the system. The "bound" water is associated with the water pools of the w/[bmim][PF6] microemulsions. Excited-state proton transfer (ESPT) involving probe pyranine shows deprotonation of pyranine within the water pools of the w/[bmim][PF6] microemulsions. PMID:25121578

  13. Dielectric spectroscopy study on ionic liquid microemulsion composed of water, TX-100, and BmimPF6.

    PubMed

    Chen, Zhen; Nozaki, Ryusuke

    2012-06-28

    We report here a broadband dielectric spectroscopy study on an ionic liquid microemulsion (ILM) composed of water, Triton X-100 (TX-100), and 1-butyl-3-methylimidazolium hexafluorophosphate (bmimPF(6)). It is found that the phase behavior of this ILM can be easily identified by its dielectric response. The dielectric behavior of the ILM in the GHz range is consistent with that of TX-100∕water mixtures with comparable water-to-TX-100 weight ratio. It consists of the relaxations due to ethylene oxide (EO) unit relaxation, hydration water dynamics, and∕or free water dynamics. The water content dependence of the EO unit relaxation suggests that this relaxation involves dynamics of hydration water molecules. In the IL-in-water microemulsion phase, it is found that bmimPF(6) molecules are preferentially dissolved in water when their concentration in water is lower than the solubility. An additional dielectric relaxation that is absent in the TX-100∕water mixtures is observed in the frequency range of 10(7)-10(8) Hz for this ILM. This low-frequency relaxation is found closely related to the bmimPF(6) molecule and could be attributed to the hopping of its cations∕anions between the anionic∕cationic sites. PMID:22755585

  14. An ionic liquid-in-water microemulsion as a potential carrier for topical delivery of poorly water soluble drug: Development, ex-vivo and in-vivo evaluation.

    PubMed

    Goindi, Shishu; Kaur, Ramanpreet; Kaur, Randeep

    2015-11-30

    In this paper, we report an ionic liquid-in-water (IL/w) microemulsion (ME) formulation which is able to solubilize etodolac (ETO), a poorly water soluble drug for topical delivery using BMIMPF6 (1-butyl-3-methylimidazolium hexafluorophosphate) as IL, Tween 80 as surfactant and ethanol as co-surfactant. The prepared ME was characterized for physicochemical parameters, subjected to ex-vivo permeation studies as well as in-vivo pharmacodynamic evaluation. The ex-vivo drug permeation studies through rat skin was performed using Franz-diffusion cell and the IL/w based ME showed maximum mean cumulative percent permeation of 99.030±0.921% in comparison to oil-in-water (o/w) ME (61.548±1.875%) and oily solution (48.830±2.488%) of ETO. In-vivo anti-arthritic and anti-inflammatory activities of the prepared formulations were evaluated using different rodent models and the results revealed that ETO loaded IL/w based ME was found to be more effective in controlling inflammation than oily solution, o/w ME and marketed formulation of ETO. Histopathological studies also demonstrated that IL/w based ME caused no anatomical and pathological changes in the skin. PMID:26456294

  15. Novel multifunctional nanofibers based on thermoplastic polyurethane and ionic liquid: towards antibacterial, anti-electrostatic and hydrophilic nonwovens by electrospinning.

    PubMed

    Xing, Chenyang; Guan, Jipeng; Chen, Zhouli; Zhu, Yu; Zhang, Bowu; Li, Yongjin; Li, Jingye

    2015-03-13

    Novel antibacterial, anti-electrostatic, and hydrophilic nanofibers based on a blend containing thermoplastic polyurethane (TPU) and a room-temperature ionic liquid (IL), 1-butyl-3-methylimidazolium hexafluorophosphate [BMIM][PF6], were fabricated by electrospinning. We investigated the effect of the IL on the morphology and the physical properties of the TPU nanofibers. Nanofibers with a 'bead-on-string' morphology were obtained by electrospinning from a neat TPU solution. The incorporation of the IL, at levels as low as 1 wt%, largely suppressed the formation of beads during electrospinning, and homogeneous nanofibers were obtained. The as-spun TPU/IL composite nanofibers showed significant activity against both Escherichia coli (E coli) and Staphylococcus aureus (S. aureus), with antibacterial activities of more than four and three, respectively. This means that the antibacterial efficiencies of TPU/IL composite nanofibers toward E coli and S. aureus are 99.99% and 99.9%, respectively. Moreover, nonwoven fabrics derived from the electrospun TPU/IL composite nanofibers exhibit better stretchability, elasticity, and higher electrical conductivity compared to those made using neat TPU without an IL. Additionally, the incorporation of the IL leads to a hydrophilic surface for the TPU/IL composite nanofibers compared to hydrophobic neat TPU nanofibers. These multifunctional nanofibers with excellent antibacterial, anti-electrostatic, and mechanical properties and improved hydrophilicity are promising candidates for biomedical and wastewater treatment applications. PMID:25686531

  16. Lyotropic Phase Behavior of Polybutadiene-Poly(ethylene oxide) Diblock Copolymers in Ionic Liquids

    SciTech Connect

    Simone, Peter M.; Lodge, Timothy P.

    2008-08-26

    The lyotropic phase behavior of three poly(1,2-butadiene-b-ethylene oxide) diblock copolymers (PB-PEO) with different monomer volume fractions has been studied in two different ionic liquids, 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([EMI][TFSI]) and 1-butyl-3-methylimidazolium hexafluorophosphate ([BMI][PF{sub 6}]), across the complete concentration range. The ordered microstructures present in the solutions were characterized via small-angle X-ray scattering (SAXS). The phase diagrams for the PB-PEO/ionic liquid solutions include regions corresponding to the classical copolymer microstructures: body-centered-cubic lattices of spheres, hexagonally ordered cylinders, and lamellae. Additionally, the phase diagrams also include wide regions of coexisting microstructures and regions apparently corresponding to a disordered network microstructure. The phase behavior of the PB-PEO copolymers in both ionic liquids was comparable to their previously reported aqueous solution behavior. The temperature dependence of the phase diagrams was very modest, indicative of a highly segregated system. The level of solvent selectivity was also investigated via cryogenic transmission electron microscopy (cryo-TEM) on dilute solutions. On the basis of the morphology of the dilute solution copolymer aggregate structures in the ionic liquid solvents, and on the structural length scales of the concentrated solutions, it was concluded that for PB-PEO [BMI][PF{sub 6}] behaves as a more selective solvent than [EMI][TFSI].

  17. MD simulations of the formation of stable clusters in mixtures of alkaline salts and imidazolium-based ionic liquids.

    PubMed

    Méndez-Morales, Trinidad; Carrete, Jesús; Bouzón-Capelo, Silvia; Pérez-Rodríguez, Martín; Cabeza, Óscar; Gallego, Luis J; Varela, Luis M

    2013-03-21

    Structural and dynamical properties of room-temperature ionic liquids containing the cation 1-butyl-3-methylimidazolium ([BMIM](+)) and three different anions (hexafluorophosphate, [PF6](-), tetrafluoroborate, [BF4](-), and bis(trifluoromethylsulfonyl)imide, [NTf2](-)) doped with several molar fractions of lithium salts with a common anion at 298.15 K and 1 atm were investigated by means of molecular dynamics simulations. The effect of the size of the salt cation was also analyzed by comparing these results with those for mixtures of [BMIM][PF6] with NaPF6. Lithium/sodium solvation and ionic mobilities were analyzed via the study of radial distribution functions, coordination numbers, cage autocorrelation functions, mean-square displacements (including the analysis of both ballistic and diffusive regimes), self-diffusion coefficients of all the ionic species, velocity and current autocorrelation functions, and ionic conductivity in all the ionic liquid/salt systems. We found that lithium and sodium cations are strongly coordinated in two different positions with the anion present in the mixture. Moreover, [Li](+) and [Na](+) cations were found to form bonded-like, long-lived aggregates with the anions in their first solvation shell, which act as very stable kinetic entities within which a marked rattling motion of salt ions takes place. With very long MD simulation runs, this phenomenon is proved to be on the basis of the decrease of self-diffusion coefficients and ionic conductivities previously reported in experimental and computational results. PMID:23480174

  18. Chromatographic determination of biogenic amines in wines after treatment with ionic liquids as novel media.

    PubMed

    Jiang, Hai-Liang; Ying, Li-Yan; Zhou, Sai-Chun; Ying, Min; Shen, Wei; Qiu, Dong-He

    2011-05-01

    Room temperature ionic liquids (RTIL), 1-butyl-3-methylimidazolium hexafluorophosphate ([C(4) MIM][PF(6) ]), were used as the novel media for derivatization, extraction and preconcentration of biogenic amines (BAs) in wines. Six BAs, tryptamine (Try), phenylethylamine (Phe), putrescine (Put), cadaverine (Cad), tyramine (Tyr) and spermine (Spe) were selected as the model compounds and dansyl chloride (Dns-Cl) as the derivatizing reagent. The derivatizations of amines were conducted in water-IL two-phase system, in which the partition property of related substance in the IL was investigated and the mechanism (http://www.iciba.com/mechanism/) of derivation and extraction of amines was discussed. The influencing factors, including sample volume, derivatizing reagent concentration, pH value and ultrasound reaction time, were optimized. The Dns-amines were separated by high-performance liquid chromatography (HPLC), and detected with UVD at 254 nm. For each of the tested amines, a good linearity was obtained in the concentration range of 0.1-20 mg/L with the correlation coefficient (R) of 0.9814-0.9930. The limits of detection reached μg/L level and the relative standard deviations (RSD, n=3) were between 3.2 and 8.1%. Satisfactory recovery for each BA was obtained, ranging from 82.3 to 114.0%. The developed method was successfully applied to determine six BAs in red wines and Chinese yellow wine. PMID:21416603

  19. A derivative photoelectrochemical sensing platform for herbicide acetochlor based on TiO₂-poly (3-hexylthiophene)-ionic liquid nanocomposite film modified electrodes.

    PubMed

    Jin, Dangqin; Xu, Qin; Wang, Yanjuan; Hu, Xiaoya

    2014-09-01

    Nonelectroactive acetochlor can be indirectly determined through the photocatalytical degradation of acetochlor. A derivative visible light photoelectrochemical sensor for indirect detection of the herbicide acetochlor using TiO2-poly(3-hexylthiophene)-ionic liquid nanocomposite is constructed. Poly(3-hexylthiophene) (P3HT) was synthesized via chemical oxidative polymerization with anhydrous FeCl3 as oxidant, 3-hexylthiophene as monomer, chloroform as solvent, and the functional TiO2 nanoparticles were facilely prepared by blending TiO2 nanoparticles and P3HT at room temperature ionic liquid, 1-Butyl-3-methylimidazolium hexafluorophosphate solution. Operational parameters, including the photolysis time, ratios of TiO2 to P3HT, bias voltage and pH of buffer solution have been optimized. Under optimal conditions, the proposed photoelectrochemical method could detect acetochlor ranging from 0.5 to 20 μmol L(-1) with a detection limit of 0.2 nmol L(-1) at a signal-to-noise ratio of 3. The assay results of acetochlor in water samples with the proposed method were in acceptable agreement with those of the gas chromatograph-mass spectrometer (GC-MS) method. The promising sensor opens a new opportunity for fast, portable, and sensitive analysis of acetochlor in environmental samples. PMID:24913872

  20. Ultrasensitive electrochemical biosensor based on reduced graphene oxide-tetraethylene pentamine-BMIMPF6 hybrids for the detection of α2,6-sialylated glycans in human serum.

    PubMed

    Li, Yuliang; He, Junlin; Niu, Yazhen; Yu, Chao

    2015-12-15

    In this paper, a simple, ultrasensitive and label-free electrochemical α2,6-sialylated glycans biosensor based on reduced graphene oxide-tetraethylene pentamine-1-butyl-3-methylimidazolium hexafluorophosphate (BMIMPF6) hybrids was developed. Due to the abundance of amino groups from reduced graphene oxide-tetraethylene pentamine (rGO-TEPA) and the electrostatic interaction of BMIMPF6, bimetallic gold platinum alloy nanoparticles (AuPtNPs) were densely adsorbed onto the surface of the nanocomposite, providing a large surface area available for the immobilization of Sambucus nigra agglutinin (SNA). AuPtNPs have excellent conductivity and catalytic activity, which can promote electron transfer between the electrolyte solution and the surface of electrode and can enhance the sensitivity of biosensor. SNA, which specifically binds α2,6-sialylated glycans, was covalently immobilized on AuPtNPs for specific detection of α2,6-sialylated glycans in human serum. Under optimal experimental conditions, amperometric response changes were used to detect α2,6-sialylated glycans with a broad linear range of 10 fg mL(-1) -1 μg mL(-1) and a low detection limit of 3 fg mL(-1) (S/N=3). When applied to spiked serum samples, the recovery of the developed biosensor ranged from 100.8% to 101.4%, suggesting that the electrochemical biosensor would be suitable for the practical detection of α2,6-sialylated glycans. PMID:26257188

  1. Nanoparticles decorated with a Schiff's base for the microextraction of Cd, Pb, Ni, and Co in environmental samples.

    PubMed

    Shah, Faheem; Naeemullah; Shah, Muhammad Raza; Kazi, Tasneem Gul; Afridi, Hassan Imran; Shah, Kiramat

    2016-05-01

    In this paper, we report a new liquid-liquid microextraction procedure called "nanoparticles decorated with a Schiff's base for the microextraction of Cd, Pb, Ni, and Co in environmental samples". The developed procedure was utilized for the extraction of Cd, Pb, Ni, and Co in environmental samples. The Schiff's base was formed by reacting salicylaldehyde with 3-aminopropyltriethoxysilane-functionalized iron oxide nanoparticles. Analyte extraction was conducted in a capillary column system loaded with modified nanoparticles and triton X-114 as dispersion medium. 1-Butyl-3-methylimidazolium hexafluorophosphate was employed as an extraction solvent. Acidified methanol in ultrasonic bath was used as desorption solvent, and elemental determination was carried out with flame atomic absorption spectrometer. Characterization of modified nanoparticles was performed with FTIR spectroscopy and transmission electron microscopy. Solution pH, nanoparticles amount, dispersant concentration, ionic liquid, and temperature were optimized for the extraction. Detection limits obtained for Cd, Pb, Ni, and Co were 0.183, 0.201, 0.241, and 0.192 μg L(-1), respectively, and enhancement factors were 79.1, 86.4, 95.7, and 82.0, respectively. The reproducibility of the developed procedure was in the range of 3.98-5.10%. Validation was checked by applying the developed procedure on certified reference water samples. The microextraction based on nanoparticles decorated with Schiff's base was successfully applied for the extraction of Cd, Pb, Ni, and Co in real environmental water samples. PMID:27187842

  2. Multivariate optimization of "In capillary-Schiff's base functionalized magnetic nanoparticle based microextraction" of Pb(+2): A novel synergistic approach.

    PubMed

    Shah, Faheem; Muhammad, Haji; Naeemullah; Ullah, Azeem

    2016-07-01

    A novel microextraction procedure based on Schiff's base functionalized magnetic nanoparticles (SBMNPs) has been developed for Pb(+2) extraction. Compared to conventional microextraction systems, the main advantage of proposed procedure is that no volatile/flammable reagents have used and experimental time is also reduced. Schiff's base has been derived from salicylaldehyde and 3-aminopropyltriethoxysilane modified nanoparticles. Extraction of Pb(+2) was carried out in a capillary column containing analyte followed by the addition of SBMNPs and triton X-114 where ionic-liquid "1-Butyl-3-methylimidazolium hexafluorophosphate" was used as an extractant. After extraction; analyte concentration was determined with flame atomic absorption spectrometer through a self made micro-injection system. The SBMNPs were characterized by FTIR and TEM, respectively, demonstrating their distinct core-shell structures. Different experimental parameters were optimized through multivariate strategy. Detection limit, enhancement factor and relative standard deviation obtained with developed procedure were 0.193μgL(-1), 26.3 and 4.01%, respectively. Validity was checked through the recovery experiments and satisfactory results were obtained. In brief the synergistic combination of SBMNPs in column with ionic-liquid resulted in an efficient microextraction procedure for Pb(+2) in real samples. PMID:27154669

  3. Reverse dynamic calorimetry of a viscous ionic liquid.

    PubMed

    Huang, Wei; Richert, Ranko

    2009-11-14

    We compare the time scale of thermal relaxation with that of the electric modulus in the deeply supercooled regime of the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate. Thermal relaxation refers to the process of configurational temperatures of the slow degrees of freedom equilibrating toward the vibrational temperature, which is a reliable indicator for the time scale of structural relaxation. Energy is supplied to the sample by absorption from a sinusoidal electric field with amplitude as high as 387 kV/cm and frequencies in the 0.2 Hz-56 kHz range, analogous to microwave heating. The time resolved response of configurational temperature as well as the low field dielectric properties are measured in a single high field impedance setup. Near T(g), we find that the macroscopic field (or modulus M) relaxes considerably faster than the structure (in terms of thermal relaxation, solvation dynamics, and probe rotation), although the liquid is entirely composed of mobile ions. PMID:19916606

  4. Bioreduction and precipitation of uranium in ionic liquid aqueous solution by Clostridium sp.

    PubMed

    Zhang, C; Dodge, C J; Malhotra, S V; Francis, A J

    2013-05-01

    The ionic liquids, 1-butyl-3-methylimidazolium hexafluorophosphate [BMIM][PF6], N-ethylpyridiniumtrifluoroacetate [EtPy][CF3COO] and N-ethylpyridiniumtetrafluoroborate [EtPy][BF4], affected the reduction and precipitation of uranium by Clostridium sp. to a varying degree. Characterization of uranium association with the ionic liquids showed that uranium formed a monodentate complex with the anion BF4(-) and PF6(-) of [EtPy][BF4] and [BMIM][PF6], respectively; and a bidentate complex with carboxylate of [EtPy][CF3COO]. Bioreduction of U(VI) was influenced by the type of complex formed: monodentate complexes were readily reduced whereas the bidentate complex of U(VI) with [CF3COO] was recalcitrant. [EtPy][BF4] affected the rate and extent of precipitation of the reduced uranium; at higher concentration the reduced U(IV) remained in the solution phase. The results suggest that by tuning the properties of ionic liquids they may be valuable candidates for uranium biotreatment. PMID:23566468

  5. Effect of water on structure and dynamics of [BMIM][PF6] ionic liquid: An all-atom molecular dynamics simulation investigation

    NASA Astrophysics Data System (ADS)

    Sharma, Anirban; Ghorai, Pradip Kr.

    2016-03-01

    Composition dependent structural and dynamical properties of aqueous hydrophobic 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF6]) ionic liquid (IL) have been investigated by using all-atom molecular dynamics simulation. We observe that addition of water does not increase significant number of dissociated ions in the solution over the pure state. As a consequence, self-diffusion coefficient of the cation and anion is comparable to each other at all water concentration similar to that is observed for the pure state. Voronoi polyhedra analysis exhibits strong dependence on the local environment of IL concentration. Void and neck distributions in Voronoi tessellation are approximately Gaussian for pure IL but upon subsequent addition of water, we observe deviation from the Gaussian behaviour with an asymmetric broadening with long tail of exponential decay at large void radius, particularly at higher water concentrations. The increase in void space and neck size at higher water concentration facilitates ionic motion, thus, decreasing dynamical heterogeneity and IL reorientation time and increases self-diffusion coefficient significantly.

  6. Distributed polarizability models for imidazolium-based ionic liquids.

    PubMed

    Millot, Claude; Chaumont, Alain; Engler, Etienne; Wipff, Georges

    2014-09-25

    Quantum chemical calculations are used to derive distributed polarizability models sufficiently accurate and compact to be used in classical molecular dynamics simulations of imidazolium-based room temperature ionic liquids. Two distributed polarizability models are fitted to reproduce the induction energy of three imidazolium cations (1,3-dimethyl-, 1-ethyl-3-methyl-, and 1-butyl-3-methylimidazolium) and four anions (tetrafluoroborate, hexafluorophosphate, nitrate, and thiocyanate) polarized by a point charge located successively on a grid of surrounding points. The first model includes charge-flow polarizabilities between first-neighbor atoms and isotropic dipolar polarizability on all atoms (except H), while the second model includes anisotropic dipolar polarizabilities on all atoms (except H). For the imidazolium cations, particular attention is given to the transferability of the distributed polarizability sets. The molecular polarizability and its anisotropy rebuilt by the distributed models are found to be in good agreement with the exact ab initio values for the three cations and 23 additional conformers of 1-ethyl-3-methyl-, 1-butyl-3-methyl-, 1-pentyl-3-methyl-, and 1-hexyl-3-methylimidazolium cations. PMID:25133873

  7. Bottom-up electrochemical preparation of solid-state carbon nanodots directly from nitriles/ionic liquids using carbon-free electrodes and the applications in specific ferric ion detection and cell imaging.

    PubMed

    Niu, Fushuang; Xu, Yuanhong; Liu, Mengli; Sun, Jing; Guo, Pengran; Liu, Jingquan

    2016-03-14

    Carbon nanodots (C-dots), a new type of potential alternative to conventional semiconductor quantum dots, have attracted numerous attentions in various applications including bio-chemical sensing, cell imaging, etc., due to their chemical inertness, low toxicity and flexible functionalization. Various methods including electrochemical (EC) methods have been reported for the synthesis of C-dots. However, complex procedures and/or carbon source-containing electrodes are often required. Herein, solid-state C-dots were simply prepared by bottom-up EC carbonization of nitriles (e.g. acetonitrile) in the presence of an ionic liquid [e.g. 1-butyl-3-methylimidazolium hexafluorophosphate (BMIMPF6)], using carbon-free electrodes. Due to the positive charges of BMIM(+) on the C-dots, the final products presented in a precipitate form on the cathode, and the unreacted nitriles and BMIMPF6 can be easily removed by simple vacuum filtration. The as-prepared solid-state C-dots can be well dispersed in an aqueous medium with excellent photoluminescence properties. The average size of the C-dots was found to be 3.02 ± 0.12 nm as evidenced by transmission electron microscopy. Other techniques such as UV-vis spectroscopy, fluorescence spectroscopy, X-ray photoelectron spectroscopy and atomic force microscopy were applied for the characterization of the C-dots and to analyze the possible generation mechanism. These C-dots have been successfully applied in efficient cell imaging and specific ferric ion detection. PMID:26891173

  8. Novel multifunctional nanofibers based on thermoplastic polyurethane and ionic liquid: towards antibacterial, anti-electrostatic and hydrophilic nonwovens by electrospinning

    NASA Astrophysics Data System (ADS)

    Xing, Chenyang; Guan, Jipeng; Chen, Zhouli; Zhu, Yu; Zhang, Bowu; Li, Yongjin; Li, Jingye

    2015-03-01

    Novel antibacterial, anti-electrostatic, and hydrophilic nanofibers based on a blend containing thermoplastic polyurethane (TPU) and a room-temperature ionic liquid (IL), 1-butyl-3-methylimidazolium hexafluorophosphate [BMIM][PF6], were fabricated by electrospinning. We investigated the effect of the IL on the morphology and the physical properties of the TPU nanofibers. Nanofibers with a ‘bead-on-string’ morphology were obtained by electrospinning from a neat TPU solution. The incorporation of the IL, at levels as low as 1 wt%, largely suppressed the formation of beads during electrospinning, and homogeneous nanofibers were obtained. The as-spun TPU/IL composite nanofibers showed significant activity against both Escherichia coli (E coli) and Staphylococcus aureus (S. aureus), with antibacterial activities of more than four and three, respectively. This means that the antibacterial efficiencies of TPU/IL composite nanofibers toward E coli and S. aureus are 99.99% and 99.9%, respectively. Moreover, nonwoven fabrics derived from the electrospun TPU/IL composite nanofibers exhibit better stretchability, elasticity, and higher electrical conductivity compared to those made using neat TPU without an IL. Additionally, the incorporation of the IL leads to a hydrophilic surface for the TPU/IL composite nanofibers compared to hydrophobic neat TPU nanofibers. These multifunctional nanofibers with excellent antibacterial, anti-electrostatic, and mechanical properties and improved hydrophilicity are promising candidates for biomedical and wastewater treatment applications.

  9. An electrochemical aptasensor electrocatalyst for detection of thrombin.

    PubMed

    Tian, Rong; Chen, Xiaojun; Li, Qingwen; Yao, Cheng

    2016-05-01

    This work reports a novel signal amplification strategy based on three-dimensional ordered macroporous C60-poly(3,4-ethylenedioxythiophene)-1-butyl-3-methylimidazolium hexafluorophosphate (3DOM C60-PEDOT-[BMIm][BF6]) for ultrasensitive detection of thrombin by cascade catalysis of Au-PEDOT@SiO2 microspheres and alcohol dehydrogenase (ADH). Au-PEDOT@SiO2 microspheres were constructed not only as nanocarriers to anchor the large amounts of secondary thrombin aptamers but also as nanocatalysts to catalyze the oxidation of ethanol efficiently. Significantly, the electrochemical signal was greatly enhanced based on cascade catalysis: First, ADH catalyzed the oxidation of ethanol to acetaldehyde with the concomitant generation of NADH in the presence of β-nicotinamide adenine dinucleotide hydrate (NAD(+)). Then, gold nanoparticles (AuNPs) as nanocatalysts could effectively catalyze NADH to produce NAD(+) with the help of PEDOT as redox probe. Under the optimal conditions, the proposed aptasensor exhibits a linear range of 2 × 10(-13) to 2 × 10(-8) M with a low detection limit of 2 × 10(-14) M for thrombin detection and shows high sensitivity and good specificity. PMID:26869084

  10. Enhanced Horizontal Transfer of Antibiotic Resistance Genes in Freshwater Microcosms Induced by an Ionic Liquid

    PubMed Central

    Wang, Qing; Mao, Daqing; Mu, Quanhua; Luo, Yi

    2015-01-01

    The spread and propagation of antibiotic resistance genes (ARGs) is a worldwide public health concern. Ionic liquids (ILs), considered as “environmentally friendly” replacements for industrial organic solvents, have been widely applied in modern industry. However, few data have been collected regarding the potential ecological and environmental risks of ILs, which are important for preparing for their potential discharge into the environment. In this paper, the IL 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIm][PF6]) (0.001-5.0 g/L) was tested for its effects on facilitating ARGs horizontal transfer mediated by plasmid RP4 in freshwater microcosms. In the horizontal transfer microcosms, the transfer frequency of plasmid RP4 was significantly enhanced (60-fold higher than untreated groups) by the IL [BMIm][PF6] (1.0 g/L). Meanwhile, two strains of opportunistic pathogen Acinetobacter spp. and Salmonella spp. were isolated among the transconjugants, illustrating plasmid RP4 mediated horizontal transfer of ARGs occurred in pathogen. This could increase the risk of ARGs dissemination to human pathogens and pose great threat to public health. The cause that [BMIm[PF6] enhanced the transfer frequency of plasmid RP4 was proposed by suppressed cell membrane barrier and enhanced cell membrane permeability, which was evidenced by flow cytometry (FCM). This is the first report that some ILs facilitate horizontal transfer of plasmid RP4 which is widely distributed in the environment and thus add the adverse effects of the environmental risk of ILs. PMID:25951456

  11. Phosphorus-doped carbon nitride solid: enhanced electrical conductivity and photocurrent generation.

    PubMed

    Zhang, Yuanjian; Mori, Toshiyuki; Ye, Jinhua; Antonietti, Markus

    2010-05-12

    As a new kind of polymeric semiconductors, graphitic carbon nitride (g-C(3)N(4)) and its incompletely condensed precursors are stable up to 550 degrees C in air and have shown promising photovoltaic applications. However, for practical applications, their efficiency, limited e.g. by band gap absorption, needs further improvement. Here we report a "structural doping" strategy, in which phosphorus heteroatoms were doped into g-C(3)N(4) via carbon sites by polycondensation of the mixture of the carbon nitride precursors and phosphorus source (specifically from 1-butyl-3-methylimidazolium hexafluorophosphate ionic liquid). Most of the structural features of g-C(3)N(4) were well retained after doping, but electronic features had been seriously altered, which provided not only a much better electrical (dark) conductivity up to 4 orders of magnitude but also an improvement in photocurrent generation by a factor of up to 5. In addition to being active layers in solar cells, such phosphorus-containing scaffolds and materials are also interesting for polymeric batteries as well as for catalysis and as catalytic supports. PMID:20397632

  12. Two-dimensional ion chromatography for the separation of ionic organophosphates generated in thermally decomposed lithium hexafluorophosphate-based lithium ion battery electrolytes.

    PubMed

    Kraft, Vadim; Grützke, Martin; Weber, Waldemar; Menzel, Jennifer; Wiemers-Meyer, Simon; Winter, Martin; Nowak, Sascha

    2015-08-28

    A two-dimensional ion chromatography (IC/IC) technique with heart-cutting mode for the separation of ionic organophosphates was developed. These analytes are generated during thermal degradation of three different commercially available Selectilyte™ lithium ion battery electrolytes. The composition of the investigated electrolytes is based on 1M lithium hexafluorophosphate (LiPF6) dissolved in ethylene carbonate/dimethyl carbonate (50:50wt%, LP30), ethylene carbonate/diethyl carbonate (50:50wt%, LP40) and ethylene carbonate/ethyl methyl carbonate (50:50wt%, LP50). The organophosphates were pre-separated from PF6(-) anion on the low capacity A Supp 4 column, which was eluted with a gradient step containing acetonitrile. The fraction containing analytes was retarded on a pre-concentration column and after that transferred to the high capacity columns, where the separation was performed isocratically. Different stationary phases and eluents were applied on the 2nd dimension for the investigation of retention times, whereas the highly promising results were obtained with a high capacitive A Supp 10 column. The organophosphates generated in LP30 and LP40 electrolytes could be separated by application of an aqueous NaOH eluent providing fast analysis time within 35min. For the separation of the organophosphates of LP50 electrolyte due to its complexity a NaOH eluent containing a mixture of methanol/H2O was necessary. In addition, the developed two dimensional IC method was hyphenated to an inductively coupled plasma mass spectrometer (ICP-MS) using aqueous NaOH without organic modifiers. This proof of principle measurement was carried out for future quantitative investigation regarding the concentration of the ionic organophosphates. Furthermore, the chemical stability of several ionic organophosphates in water and acetonitrile at room temperature over a period of 10h was investigated. In both solvents no decomposition of the investigated analytes was observed and

  13. Bottom-up electrochemical preparation of solid-state carbon nanodots directly from nitriles/ionic liquids using carbon-free electrodes and the applications in specific ferric ion detection and cell imaging

    NASA Astrophysics Data System (ADS)

    Niu, Fushuang; Xu, Yuanhong; Liu, Mengli; Sun, Jing; Guo, Pengran; Liu, Jingquan

    2016-03-01

    Carbon nanodots (C-dots), a new type of potential alternative to conventional semiconductor quantum dots, have attracted numerous attentions in various applications including bio-chemical sensing, cell imaging, etc., due to their chemical inertness, low toxicity and flexible functionalization. Various methods including electrochemical (EC) methods have been reported for the synthesis of C-dots. However, complex procedures and/or carbon source-containing electrodes are often required. Herein, solid-state C-dots were simply prepared by bottom-up EC carbonization of nitriles (e.g. acetonitrile) in the presence of an ionic liquid [e.g. 1-butyl-3-methylimidazolium hexafluorophosphate (BMIMPF6)], using carbon-free electrodes. Due to the positive charges of BMIM+ on the C-dots, the final products presented in a precipitate form on the cathode, and the unreacted nitriles and BMIMPF6 can be easily removed by simple vacuum filtration. The as-prepared solid-state C-dots can be well dispersed in an aqueous medium with excellent photoluminescence properties. The average size of the C-dots was found to be 3.02 +/- 0.12 nm as evidenced by transmission electron microscopy. Other techniques such as UV-vis spectroscopy, fluorescence spectroscopy, X-ray photoelectron spectroscopy and atomic force microscopy were applied for the characterization of the C-dots and to analyze the possible generation mechanism. These C-dots have been successfully applied in efficient cell imaging and specific ferric ion detection.Carbon nanodots (C-dots), a new type of potential alternative to conventional semiconductor quantum dots, have attracted numerous attentions in various applications including bio-chemical sensing, cell imaging, etc., due to their chemical inertness, low toxicity and flexible functionalization. Various methods including electrochemical (EC) methods have been reported for the synthesis of C-dots. However, complex procedures and/or carbon source-containing electrodes are often

  14. X-ray and Synchrotron Diffraction Studies of 2-(Pyridin-2-yl)-1,10- Phenanthroline in the Role of Ligand for Two Copper Polymorphs or Hydrogen bonded with 2,2,6,6-Tetramethyl-4-oxopiperidinium Hexafluorophosphate

    SciTech Connect

    Krause, Jeanette A.; Zhao, Daoli; Chatterjee, Sayandev; Yeung, Bonnie M.; Connick, William B.; Collins, Sibrina N.

    2013-12-01

    Different extended packing motifs of dichloro-[2-(pyridin-2-yl)-1,10-phenanthroline]copper(II), CuCl2 (C17H11N3Cl2) are obtained depending on the crystallization conditions. A triclinic form (I) is obtained from dimethylformamide-diethyl ether or methanol whereas crystallization from dimethylformamide-water yields a monoclinic form (II). In each case, the CuII center is in a 5-coordinate, distorted square-pyramidal geometry. The extended packing for both forms can be described as a highly-offset π stacking arrangement with interlayer distances of 3.674 (3) and 3.679 (3) Å for (I) and (II), respectively. The reaction of diprotonated Pt(tmpip2NCN)Cl (tmpip2NCN = 2,6-bis(2,2,6,6-tetramethylpiperidylmethyl)- benzyl) with AgPF6 under acidic conditions followed by the addition of 2-(pyridin-2-yl)-1,10-phenanthroline, results in a hydrogen bonded co-crystal, 2,2,6,6-tetramethyl-4-oxopiperidinium hexafluorophosphate- 2-(pyridin-2-yl)-1,10-phenanthroline (1/1),C9H18NO+.PF6-.C17H11N3.(III). The extended packing maximizes π-π interactions in a parallel, faceto-face arrangement with an interlayer stacking distance of 3.4960 (14) Å.

  15. [Analysis of aliphatic aldehydes and ketones in water-based adhesive by direct derivatization-ionic liquid gathering coupled with high performance liquid chromatography].

    PubMed

    Wan, Xiaohong; Wu, Mingjian; Jiang, Xinyu; Dai, Yunhui; Li, Shaoye; Gong, Shuguo

    2011-12-01

    A novel method was developed for trace analysis of aliphatic aldehydes and ketones in water-based adhesive based on 2,4-dinitrophenylhydrazine (DNPH) direct derivatization-1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM] PF6) preconcentration coupled with high performance liquid chromatography (HPLC). The dispersive water-based adhesive emulsion directly reacted with 80 mg/L DNPH solution containing 0.44 mol/L phosphoric acid at 40 degrees C for 18 min. After centrifuging, 0.5 mL [BMIM] PF6 was added to extract the derivatives at 30 degrees C. The ionic liquid (IL) phase was filtered and then analyzed by HPLC. The separation was achieved by using a Dionex Acclaim Explosive E2 column (250 mm x 4.6 mm, 5 microm) under the gradient elution with acetonitrile and water as mobile phases at the flow rate of 1.2 mL/min. The column temperature was 35 degrees C, and the detection wavelength was 365 nm. The results showed that the limits of detection (LODs) were 0.022 -0.221 mg/kg, and the limits of quantification (LOQs) were 0.073 - 0.738 mg/kg. The relative standard deviations (RSDs) were in the range of 3.5% - 7.3%, and the recoveries were 84.0% - 102.5% for 8 aliphatic aldehydes and ketones. Compared with solvent extraction, the established method has the advantages of lower LOD and LOQ, and is more stable and precise. This method is practical for the determination of aliphatic aldehydes and ketones in water-based adhesives. PMID:22500444

  16. Flow-focusing generation of monodisperse water droplets wrapped by ionic liquid on microfluidic chips: from plug to sphere.

    PubMed

    Wang, Wei-Han; Zhang, Zhi-Ling; Xie, Ya-Ni; Wang, Li; Yi, Song; Liu, Kan; Liu, Jia; Pang, Dai-Wen; Zhao, Xing-Zhong

    2007-11-01

    Generating droplets via microfluidic chips is a promising technology in microanalysis and microsynthesis. To realize room-temperature ionic liquid (IL)-water two-phase studies in microscale, a water-immiscible IL was employed as the continuous phase for the first time to wrap water droplets (either plugs or spheres) on flow-focusing microfluidic chips. The IL, 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF6]), could wet both hydrophilic and hydrophobic channel surfaces because of its dual role of hydrophilicity/hydrophobicity and extremely high viscosity, thus offering the possibility of wrapping water droplets in totally hydrophilic (THI), moderately hydrophilic (MHI), and hydrophobic (HO) channels. The droplet shape could be tuned from plug to sphere, with the volume from 6.3 nL to 65 pL, by adding an orifice in the focusing region, rendering the hydrophilic channel surface hydrophobic, and suppressing the Uw/UIL ratio below 1.0. Three different breakup processes were defined and clarified, in which the sub-steady breakup and steady breakup were essential for the formation of plugs and spheric droplets, respectively. The influences of channel hydrophilicity/hydrophobicity on droplet formation were carefully studied by evaluating the wetting abilities of water and IL on different surfaces. The superiority of IL over water in wetting hydrophobic surface led to the tendency of forming small, spheric aqueous droplets in the hydrophobic channel. This IL-favored droplet-based system represented a high efficiency in water/IL extraction, in which rhodamine 6G was extracted from aqueous droplets to [BMIM][PF6] in the hydrophobic orifice-included (HO-OI) channel in 0.51 s. PMID:17918864

  17. Aggregation of a model porphyrin within poly(ethylene glycol) (PEG): effect of water, PEG molecular weight, ionic liquids, salts, and temperature.

    PubMed

    Rai, Rewa; Kumar, Vinod; Pandey, Siddharth

    2014-04-28

    Understanding molecular aggregation within environmentally-benign media is of utmost importance. Aggregation of a common porphyrin, 5,10,15,20-tetrakis(4-sulfonatophenyl)porphyrin (TSPP), dissolved in media composed of poly(ethylene glycols) (PEGs) up to an average molecular weight (MW) of 8000 as major components, is investigated. J-aggregates of TSPP are well-manifested via the bathochromically-shifted UV-vis absorbance band of TSPP. As media, 10 wt% water-added PEGs at pH 1 show excellent efficiency for TSPP J-aggregation. The J-aggregation efficiency increases as the PEG MW is increased and it is found to be the maximum for the medium constituted of PEG3000. Once formed, some of the J-aggregates decay back to the diprotonated form via pseudo-first order kinetics. Addition of salts NaCl and NaBF4 and ionic liquids [bmim][PF6], [bmim][Tf2N], [bmim][BF4], and [bmim][OTf] [bmim = 1-butyl-3-methylimidazolium, PF6 = hexafluorophosphate, Tf2N = bis(trifluoromethylsulfonyl)imide, BF4 = tetrafluoroborate, and OTf = trifluoromethanesulfonate], respectively, to TSPP dissolved in 10 wt% water added PEGs at pH 1 results in increased J-aggregation efficiency. Ionic liquids are found to protect porphyrin J-aggregates from decaying to their diprotonated form. Increasing temperature from ambient to 90 °C results in decreased J-aggregation efficiency of TSPP in the presence of salts NaCl and NaBF4, respectively; concentration of J-aggregates does not change much with temperature when an ionic liquid as an additive is present in the medium. The polymer chain length and electrostatic interactions appear to play a major role in porphyrin J-aggregation efficiency and kinetics within water-added acidic mixtures of PEG. PMID:24618770

  18. Water in Room Temperature Ionic Liquids

    NASA Astrophysics Data System (ADS)

    Fayer, Michael

    2014-03-01

    Room temperature ionic liquids (or RTILs, salts with a melting point below 25 °C) have become a subject of intense study over the last several decades. Currently, RTIL application research includes synthesis, batteries, solar cells, crystallization, drug delivery, and optics. RTILs are often composed of an inorganic anion paired with an asymmetric organic cation which contains one or more pendant alkyl chains. The asymmetry of the cation frustrates crystallization, causing the salt's melting point to drop significantly. In general, RTILs are very hygroscopic, and therefore, it is of interest to examine the influence of water on RTIL structure and dynamics. In addition, in contrast to normal aqueous salt solutions, which crystallize at low water concentration, in an RTIL it is possible to examine isolated water molecules interacting with ions but not with other water molecules. Here, optical heterodyne-detected optical Kerr effect (OHD-OKE) measurements of orientational relaxation on a series of 1-alkyl-3-methylimidazolium tetrafluoroborate RTILs as a function of chain length and water concentration are presented. The addition of water to the longer alkyl chain RTILs causes the emergence of a long time bi-exponential orientational anisotropy decay. Such decays have not been seen previously in OHD-OKE experiments on any type of liquid and are analyzed here using a wobbling-in-a-cone model. The orientational relaxation is not hydrodynamic, with the slowest relaxation component becoming slower as the viscosity decreases for the longest chain, highest water content samples. The dynamics of isolated D2O molecules in 1-butyl-3-methylimidazolium hexafluorophosphate (BmImPF6) were examined using two dimensional infrared (2D IR) vibrational echo spectroscopy. Spectral diffusion and incoherent and coherent transfer of excitation between the symmetric and antisymmetric modes are examined. The coherent transfer experiments are used to address the nature of inhomogeneous

  19. Estimation of lead in biological samples of oral cancer patients chewing smokeless tobacco products by ionic liquid-based microextraction in a single syringe system.

    PubMed

    Arain, Sadaf S; Kazi, Tasneem G; Arain, Asma J; Afridi, Hassan I; Arain, Muhammad B; Brahman, Kapil D; Naeemullah; Panhwar, Abdul H; Arain, Mariam S

    2015-08-01

    Several studies have reported that the chewing habit of smokeless tobacco (SLT) has been associated with oral cancer. The aim of the present study was to evaluate the trace levels of lead (Pb) in biological samples (blood, scalp hair) of oral cancer patients and referents of the same age group (range 30-60 years). As the concentrations of Pb are very low in biological samples, so a simple and efficient ionic liquid-based microextraction in a single syringe system has been developed, as a prior step to determination by flame atomic absorption spectrometry. In this procedure, the hydrophobic chelates of Pb with ammonium pyrrolidinedithiocarbamate (APDC) were extracted into fine droplets of 1-butyl-3-methylimidazolium hexafluorophosphate [C4MIM][PF6] within a syringe while using Triton X-114 as a dispersant. Factors influencing the microextraction efficiency and determination, such as pH of the sample, volume of [C4MIM][PF6] and Triton X-114, ligand concentration, and incubation time, were studied. To validate the proposed method, certified reference materials were analyzed and the results of Pb(2+) were in good agreement with certified values. At optimum experimental values of significant variables, detection limit and enhancement factor were found to be 0.412 μg/L and 80, respectively. The coexisting ions showed no obvious negative outcome on Pb preconcentration. The proposed method was applied satisfactorily for the preconcentration of Pb(2+) in acid-digested SLT and biological samples of the study population. It was observed that oral cancer patients who consumed different SLT products have 2-3-fold higher levels of Pb in scalp hair and blood samples as compared to healthy referents (p < 0.001). While 31.4-50.8% higher levels of Pb were observed in referents chewing different SLT products as compared to nonconsumers (p < 0.01). PMID:25903188

  20. Temperature controlled ionic liquid-based dispersive micro-extraction using two ligands, for determination of aluminium in scalp hair samples of Alzheimer's patients: a multivariate study.

    PubMed

    Arain, Mariam S; Arain, Salma A; Kazi, Tasneem G; Afridi, Hassan I; Ali, Jamshaid; Naeemulllah; Arain, Sadaf S; Brahman, Kapil Dev; Mughal, Moina Akhtar

    2015-02-25

    A green and sensitive temperature controlled dispersive liquid-liquid microextraction (TIL-DLLME) methodology based on the application of ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate, [C4mim][PF6], as an extractant solvent was proposed for the preconcentration of trace levels of aluminium (Al(3+)) in scalp hair samples of Alzheimer's (AD) patients, prior to analyzing by flame atomic absorption spectrometry (FAAS). The Al(3+) was complexed with 8-hydrooxyquinoline (oxine) (L1) and 3,5,7,2'-4' pentahydroxy flavone (morin) (L2) separately and then extracted by IL at temperature (50±2.0°C). Some effective factors that influence the TIL-DLLME efficiency such as pH, ligands concentrations, volume of IL, ionic strength, and incubation time were investigated and optimized by multivariate analysis. In the optimum experimental conditions, the limit of detection (3s) and enhancement factor were 0.56 μg L(-1), 0.64 μg L(-1) and 85, 73 for both ligands, respectively. The relative standard deviation (RSD) for six replicate determinations of 100 μg L(-1) Al(3+) complexed with oxine and morin were found to be 3.88% and 4.74%, respectively. The developed method was validated by the analysis of certified reference material of human hair (NCSZC81002).and applied satisfactorily to the determination of Al(3+) in acid digested scalp hair samples of AD patients and healthy controls. The resulted data shows significant higher level in scalp hair samples of AD male patients with related to referents of same age and socioeconomic status. PMID:25280335

  1. Ultrafast vibrational spectroscopy (2D-IR) of CO2 in ionic liquids: Carbon capture from carbon dioxide's point of view.

    PubMed

    Brinzer, Thomas; Berquist, Eric J; Ren, Zhe; Dutta, Samrat; Johnson, Clinton A; Krisher, Cullen S; Lambrecht, Daniel S; Garrett-Roe, Sean

    2015-06-01

    The CO2ν3 asymmetric stretching mode is established as a vibrational chromophore for ultrafast two-dimensional infrared (2D-IR) spectroscopic studies of local structure and dynamics in ionic liquids, which are of interest for carbon capture applications. CO2 is dissolved in a series of 1-butyl-3-methylimidazolium-based ionic liquids ([C4C1im][X], where [X](-) is the anion from the series hexafluorophosphate (PF6 (-)), tetrafluoroborate (BF4 (-)), bis-(trifluoromethyl)sulfonylimide (Tf2N(-)), triflate (TfO(-)), trifluoroacetate (TFA(-)), dicyanamide (DCA(-)), and thiocyanate (SCN(-))). In the ionic liquids studied, the ν3 center frequency is sensitive to the local solvation environment and reports on the timescales for local structural relaxation. Density functional theory calculations predict charge transfer from the anion to the CO2 and from CO2 to the cation. The charge transfer drives geometrical distortion of CO2, which in turn changes the ν3 frequency. The observed structural relaxation timescales vary by up to an order of magnitude between ionic liquids. Shoulders in the 2D-IR spectra arise from anharmonic coupling of the ν2 and ν3 normal modes of CO2. Thermal fluctuations in the ν2 population stochastically modulate the ν3 frequency and generate dynamic cross-peaks. These timescales are attributed to the breakup of ion cages that create a well-defined local environment for CO2. The results suggest that the picosecond dynamics of CO2 are gated by local diffusion of anions and cations. PMID:26049445

  2. Non-covalent interactions in ionic liquid ion pairs and ion pair dimers: a quantum chemical calculation analysis.

    PubMed

    Marekha, Bogdan A; Kalugin, Oleg N; Idrissi, Abdenacer

    2015-07-14

    Ionic liquids (ILs) being composed of bulky multiatomic ions reveal a plethora of non-covalent interactions which determine their microscopic structure. In order to establish the main peculiarities of these interactions in an IL-environment, we have performed quantum chemical calculations for a set of representative model molecular clusters. These calculations were coupled with advanced methods of analysis of the electron density distribution, namely, the quantum theory of atoms in molecules (QTAIM) and the non-covalent interaction (NCI; J. Am. Chem. Soc., 2010, 132, 6499) approaches. The former allows for profound quantitative characterization of non-covalent interactions between atoms while the latter gives an overview of spatial extent, delocalization, and relative strength of such interactions. The studied systems consist of 1-butyl-3-methylimidazolium (Bmim(+)) cations and different perfluorinated anions: tetrafluoroborate (BF4(-)), hexafluorophosphate (PF6(-)), trifluoromethanesulfonate (TfO(-)), and bis(trifluoromethanesulfonyl)imide (TFSI(-)). IL ion pairs and ion pair dimers were considered as model structures for the neat ILs and large aggregates. Weak electrostatic hydrogen bonding was found between the anions and the imidazolium ring hydrogen atoms of cations. Weaker but still appreciable hydrogen bonding was also noted for hydrogen atoms adjacent to the imidazolium ring alkyl groups of Bmim(+). The relative strength of the hydrogen bonding is higher in BmimTfO and BmimBF4 ILs than in BmimPF6 and BmimTFSI, whereas BmimTfO and BmimTFSI reveal higher sensitivity of hydrogen bonding at the different hydrogen atoms of the imidazolium ring. PMID:26059822

  3. Ionic Liquid-Induced Unprecedented Size Enhancement of Aggregates within Aqueous Sodium Dodecylbenzene Sulfonate

    SciTech Connect

    Rai, Rewa; Baker, Gary A; Behera, Kamalakanta; Mohanty, Pravakar; Kurur, Narayanan; Pandey, Siddharth

    2010-01-01

    Physicochemical properties of aqueous micellar solutions may change in the presence of ionic liquids (ILs). Micelles help to increase the aqueous solubility of ILs. The average size of the micellar aggregates within aqueous sodium dodecylbenzene sulfonate (SDBS) is observed by dynamic light scattering (DLS) and transmission electron microscopy (TEM) to increase in a sudden and drastic fashion as the IL 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF6]) is added. Similar addition of [bmim][PF6] to aqueous sodium dodecyl sulfate (SDS) results in only a slow gradual increase in average aggregate size. While addition of the IL [bmim][BF4] also gives rise to sudden aggregate size enhancement within aqueous SDBS, the IL 1-ethyl-3-methylimidazolium tetrafluoroborate ([emim][BF4]), and inorganic salts NaPF6 and NaBF4, only gradually increase the assembly size upon their addition. Bulk dynamic viscosity, microviscosity, dipolarity (indicated by the fluorescent reporter pyrene), zeta potential, and electrical conductance measurements were taken to gain insight into this unusual size enhancement. It is proposed that bmim cations of the IL undergo Coulombic attractive interactions with anionic headgroups at the micellar surface at all [bmim][PF6] concentrations in aqueous SDS; in aqueous SDBS, beyond a critical IL concentration, bmim becomes involved in cation- interaction with the phenyl moiety of SDBS within micellar aggregates with the butyl group aligned along the alkyl chain of the surfactant. This relocation of bmim results in an unprecedented size increase in micellar aggregates. Aromaticity of the IL cation alongside the presence of sufficiently aliphatic (butyl or longer) alkyl chains on the IL appear to be essential for this dramatic critical expansion in self-assembly dimensions within aqueous SDBS.

  4. Speciation of copper-humic acid in zeolite Y during extraction with a RTIL

    NASA Astrophysics Data System (ADS)

    Huang, Hsin-Liang; Jyun Chen, Yan

    2010-07-01

    Chemical structure of copper chelated with humic acid (Cu-HA) in the micro-pores of zeolite Y (to simulate micropores in copper contaminated soils) and extracted with a room temperature ionic liquid (RTIL) ([C 4mim][PF 6], 1-butyl-3-methylimidazolium hexafluorophosphate) has been studied by X-ray absorption (near edge structure (XANES) and Fourier transformed extended X-ray absorption fine structure (EXAFS)) spectroscopy. At the temperature of 298 K, within 30 min, about 84% of Cu-HA in Y can be extracted by the RTIL. The XANES spectra reveal that a small amount of Cu(II)-HA (7%), adsorbed Cu(II) ( Cu(ads)2+) (5%) and Cu[mim]42+ (4%), which are not extracted, are found in Y. In the copper extracted RTIL, 75% of Cu(II)-HA in Y are converted to Cu[mim]42+ during extraction. About 17% of Cu(II)-HA is also found in the RTIL. Therefore, at least three reaction paths may be involved in the extraction process: (1) extraction of Cu(II)-HA in the RTIL, (2) Cu 2+ (formed from dissociation of Cu(II)-HA in the RTIL) adsorbed on Y, and (3) inter-conversion of Cu(II)-HA to Cu[mim]42+ in the RTIL. The refined EXAFS data indicate that the Cu-O bond distance in the Y and RTIL phases is 1.94 Å with an average coordination number (CN) of 3.4. Note that Cu[mim]42+ in the RTIL processes a Cu-N bond distance of 1.96 Å and a CN of 4.1.

  5. Room temperature ionic liquid-based dispersive liquid phase microextraction for the separation/preconcentration of trace Cd(2+) as 1-(2-pyridylazo)-2-naphthol (PAN) complex from environmental and biological samples and determined by FAAS.

    PubMed

    Khan, Sumaira; Soylak, Mustafa; Kazi, Tasneem Gul

    2013-12-01

    The current work develops a new green methodology for the separation/preconcentration of cadmium ions (Cd(2+)) using room temperature ionic liquid-dispersive liquid phase microextraction (RTIL-DLME) prior to analysis by flame atomic absorption spectrometry with microsample introduction system. Room temperature ionic liquids (RTIL) are considered "Green Solvents" for their thermally stable and non-volatile properties, here 1-butyl-3-methylimidazolium hexafluorophosphate [C4mim][PF6] was used as an extractant. The preconcentration of Cd(2+) in different waters and acid digested scalp hair samples were complexed with 1-(2-pyridylazo)-2-naphthol and extracted into the fine drops of RTILs. Some significant factors influencing the extraction efficiency of Cd(2+) and its subsequent determination, including pH, amount of ligand, volume of RTIL, dispersant solvent, sample volume, temperature, and incubation time were investigated in detail. The limit of detection and the enhancement factor under the optimal conditions were 0.05 μg/L and 50, respectively. The relative standard deviation of 100 μg/L Cd(2+) was 4.3 %. The validity of the proposed method was checked by determining Cd(2+) in certified reference material (TM-25.3 fortified water). The sufficient recovery (>98 %) of Cd(2+) with the certified value. The mean concentrations of Cd in lake water 13.2, waste water 15.7 and hair sample 16.8 μg/L, respectively and the developed method was applied satisfactorily to the preconcentration and determination of Cd(2+) in real samples. PMID:24197606

  6. A new dispersive liquid-liquid microextraction using ionic liquid based microemulsion coupled with cloud point extraction for determination of copper in serum and water samples.

    PubMed

    Arain, Salma Aslam; Kazi, Tasneem Gul; Afridi, Hassan Imran; Arain, Mariam Shahzadi; Panhwar, Abdul Haleem; Khan, Naeemullah; Baig, Jameel Ahmed; Shah, Faheem

    2016-04-01

    A simple and rapid dispersive liquid-liquid microextraction procedure based on ionic liquid assisted microemulsion (IL-µE-DLLME) combined with cloud point extraction has been developed for preconcentration copper (Cu(2+)) in drinking water and serum samples of adolescent female hepatitits C (HCV) patients. In this method a ternary system was developed to form microemulsion (µE) by phase inversion method (PIM), using ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate ([C4mim][PF6]) and nonionic surfactant, TX-100 (as a stabilizer in aqueous media). The Ionic liquid microemulsion (IL-µE) was evaluated through visual assessment, optical light microscope and spectrophotometrically. The Cu(2+) in real water and aqueous acid digested serum samples were complexed with 8-hydroxyquinoline (oxine) and extracted into IL-µE medium. The phase separation of stable IL-µE was carried out by the micellar cloud point extraction approach. The influence of of different parameters such as pH, oxine concentration, centrifugation time and rate were investigated. At optimized experimental conditions, the limit of detection and enhancement factor were found to be 0.132 µg/L and 70 respectively, with relative standard deviation <5%. In order to validate the developed method, certified reference materials (SLRS-4 Riverine water) and human serum (Sero-M10181) were analyzed. The resulting data indicated a non-significant difference in obtained and certified values of Cu(2+). The developed procedure was successfully applied for the preconcentration and determination of trace levels of Cu(2+) in environmental and biological samples. PMID:26761783

  7. Temperature controlled ionic liquid-based dispersive micro-extraction using two ligands, for determination of aluminium in scalp hair samples of Alzheimer's patients: A multivariate study

    NASA Astrophysics Data System (ADS)

    Arain, Mariam S.; Arain, Salma A.; Kazi, Tasneem G.; Afridi, Hassan I.; Ali, Jamshaid; Naeemulllah; Arain, Sadaf S.; Brahman, Kapil Dev; Mughal, Moina Akhtar

    2015-02-01

    A green and sensitive temperature controlled dispersive liquid-liquid microextraction (TIL-DLLME) methodology based on the application of ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate, [C4mim][PF6], as an extractant solvent was proposed for the preconcentration of trace levels of aluminium (Al3+) in scalp hair samples of Alzheimer's (AD) patients, prior to analyzing by flame atomic absorption spectrometry (FAAS). The Al3+ was complexed with 8-hydrooxyquinoline (oxine) (L1) and 3,5,7,2‧-4‧ pentahydroxy flavone (morin) (L2) separately and then extracted by IL at temperature (50 ± 2.0 °C). Some effective factors that influence the TIL-DLLME efficiency such as pH, ligands concentrations, volume of IL, ionic strength, and incubation time were investigated and optimized by multivariate analysis. In the optimum experimental conditions, the limit of detection (3 s) and enhancement factor were 0.56 μg L-1, 0.64 μg L-1 and 85, 73 for both ligands, respectively. The relative standard deviation (RSD) for six replicate determinations of 100 μg L-1 Al3+ complexed with oxine and morin were found to be 3.88% and 4.74%, respectively. The developed method was validated by the analysis of certified reference material of human hair (NCSZC81002).and applied satisfactorily to the determination of Al3+ in acid digested scalp hair samples of AD patients and healthy controls. The resulted data shows significant higher level in scalp hair samples of AD male patients with related to referents of same age and socioeconomic status.

  8. Ultrafast vibrational spectroscopy (2D-IR) of CO2 in ionic liquids: Carbon capture from carbon dioxide's point of view

    NASA Astrophysics Data System (ADS)

    Brinzer, Thomas; Berquist, Eric J.; Ren, Zhe; Dutta, Samrat; Johnson, Clinton A.; Krisher, Cullen S.; Lambrecht, Daniel S.; Garrett-Roe, Sean

    2015-06-01

    The CO2ν3 asymmetric stretching mode is established as a vibrational chromophore for ultrafast two-dimensional infrared (2D-IR) spectroscopic studies of local structure and dynamics in ionic liquids, which are of interest for carbon capture applications. CO2 is dissolved in a series of 1-butyl-3-methylimidazolium-based ionic liquids ([C4C1im][X], where [X]- is the anion from the series hexafluorophosphate (PF 6- ), tetrafluoroborate (BF 4- ), bis-(trifluoromethyl)sulfonylimide (Tf2N-), triflate (TfO-), trifluoroacetate (TFA-), dicyanamide (DCA-), and thiocyanate (SCN-)). In the ionic liquids studied, the ν3 center frequency is sensitive to the local solvation environment and reports on the timescales for local structural relaxation. Density functional theory calculations predict charge transfer from the anion to the CO2 and from CO2 to the cation. The charge transfer drives geometrical distortion of CO2, which in turn changes the ν3 frequency. The observed structural relaxation timescales vary by up to an order of magnitude between ionic liquids. Shoulders in the 2D-IR spectra arise from anharmonic coupling of the ν2 and ν3 normal modes of CO2. Thermal fluctuations in the ν2 population stochastically modulate the ν3 frequency and generate dynamic cross-peaks. These timescales are attributed to the breakup of ion cages that create a well-defined local environment for CO2. The results suggest that the picosecond dynamics of CO2 are gated by local diffusion of anions and cations.

  9. Mesoscopic simulation of a micellar poly(N-isopropyl acrylamide)-b-(polyethylene oxide) copolymer system

    NASA Astrophysics Data System (ADS)

    Bautista-Reyes, Rubén; Soto-Figueroa, César; Vicente, Luis

    2016-05-01

    In this article we studied the micellar formation of poly(N-isopropyl acrylamide)-b-polyethylene oxide (PNIPAM-b-PEO) copolymers in an aqueous system. From molecular simulations the dependence on temperature of the Flory-Huggins interaction parameter χ for PNIPAM and PEO in water is obtained and compared with available experimental results and values from other theoretical calculations. By means of dissipative particle dynamics (DPD) we then simulated the coil-globule transition for PNIPAM chains in water with a transition temperature of around 305 K. The simulations for PNIPAM-b-PEO copolymers showed that at room temperature the chains are miscible in an aqueous phase but with a temperature increase the system turns into micelles at T  =  305 K. The change in micelle anisotropy due to a different ratio PNIPAM/PEO of chains is also analyzed. What is observed is that for large PEO the large number of dissolved PEO chains gives a large corona size and the micelle is not spherical but obloide and as the number of PNIPAM is increased the micelle acquires a spherical shape. As an important application we considered the system micelle-water/anionic liquid (1-butyl-3-methylimidazolium hexafluorophosphate [BMIM]+[PF6]-). By increasing the temperature of the system from 306 K it is shown that at T  =  345 K there is a transfer of the micelle from water to the ionic liquid phase and this was due to the change in the relative affinity of PEO to water and ionic liquid expressed by the change in χ. All the simulation outcomes are qualitatively consistent with experimental results and thus to our knowledge we give the first set of χ values for the interaction between PNIPAM and water in a wide range of temperature values.

  10. The horizontal transfer of antibiotic resistance genes is enhanced by ionic liquid with different structure of varying alkyl chain length

    PubMed Central

    Wang, Qing; Lu, Qian; Mao, Daqing; Cui, Yuxiao; Luo, Yi

    2015-01-01

    Antibiotic resistance genes (ARGs) have become a global health concern. In our previous study, an ionic liquid (IL) 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIm][PF6]) had been proven to facilitate the dissemination of ARGs in the environment. However, enhanced alkyl group chain length or the substitution of alkyl groups with the cation ring corresponded with increased antimicrobial effects. In this study, we investigated how different structures of ILs with 4, 6, and 8 C atoms in the longer alkyl chain on the imidazolium cations facilitated the dissemination of ARGs. The promotion of plasmid RP4 transfer frequency decreased with [CnMIM][BF4] increasing the alkyl chain length from 4 carbon atoms to 8 carbon atoms on the imidazolium cations, which is observed with [BMIM][BF4] (n = 4, 5.9 fold) > HMIM][BF4] (n = 6, 2.2 fold) > [OMIM][BF4] (n = 8, 1.7 fold). This illustrates that [CnMIM][BF4] with increasing the alkyl chain length exert decreasing ability in facilitating plasmid RP4 horizontal transfer, which is possibly related to IL-structure dependent toxicity. The IL-structure dependent plasmid RP4 transfer frequency was attributable to bacterial cell membrane permeability weaken with increasing alkyl chain length of [CnMIM][PF4], which was evidenced by flow cytometry. In freshwater microcosm, [CnMIm][BF4] promoted the relative abundance of the sulI and intI genes for 4.6 folds, aphA and traF for 5.2 folds higher than the untreated groups, promoting the propagation of ARGs in the aquatic environment. This is the first report that ILs with different structure of varying alkyl chain length facilitate horizontal transfer of plasmid RP4 which is widely distributed in the environment, and thus add the adverse effects of the environmental risk of ILs. PMID:26379641

  11. In vitro detection of superoxide anions released from cancer cells based on potassium-doped carbon nanotubes-ionic liquid composite gels

    NASA Astrophysics Data System (ADS)

    Li, Xiao-Rong; Wang, Bo; Xu, Jing-Juan; Chen, Hong-Yuan

    2011-12-01

    A newly developed electrochemical biosensor for the determination of superoxide anions (O2&z.rad;-) released from cancer cells using potassium-doped multi-walled carbon nanotubes (KMWNTs)-1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM]PF6) ionic liquid composite gels is demonstrated. The KMWNTs-[BMIM]PF6 can electrocatalyze oxygen reduction to generate a strong current signal in neutral solution. Compared with KMWNTs without [BMIM]PF6 or MWNTs-[BMIM]PF6 composites, the KMWNTs-[BMIM]PF6 can enhance the oxygen reduction peak current by 6.2-fold and 2.8-fold, which greatly increases the detection sensitivity of oxygen. Then, O2&z.rad;- biosensors are fabricated by mixing superoxide dismutase (SOD) in the KMWNTs-[BMIM]PF6 gels via monitoring oxygen produced by an enzymic reaction between SOD/O2&z.rad;- without the help of electron mediators. The resulting biosensors show a linear range from 0.04 to 38 μM with a high sensitivity of 98.2 μA mM-1, and a lower detection limit of 0.024 μM. The common interferents such as hydrogen peroxide (H2O2), ascorbic acid (AA), uric acid (UA), and metabolites of neurotransmitters, do not interfere with the detection of O2&z.rad;-. The proposed biosensor is tested to determine O2&z.rad;-in vitro and from liver cancer and leukemia cells and shows good application potential in biological electrochemistry.

  12. Ultrafast vibrational spectroscopy (2D-IR) of CO{sub 2} in ionic liquids: Carbon capture from carbon dioxide’s point of view

    SciTech Connect

    Brinzer, Thomas; Berquist, Eric J.; Ren, Zhe; Dutta, Samrat; Johnson, Clinton A.; Krisher, Cullen S.; Lambrecht, Daniel S.; Garrett-Roe, Sean

    2015-06-07

    The CO{sub 2}ν{sub 3} asymmetric stretching mode is established as a vibrational chromophore for ultrafast two-dimensional infrared (2D-IR) spectroscopic studies of local structure and dynamics in ionic liquids, which are of interest for carbon capture applications. CO{sub 2} is dissolved in a series of 1-butyl-3-methylimidazolium-based ionic liquids ([C{sub 4}C{sub 1}im][X], where [X]{sup −} is the anion from the series hexafluorophosphate (PF{sub 6}{sup −}), tetrafluoroborate (BF{sub 4}{sup −}), bis-(trifluoromethyl)sulfonylimide (Tf{sub 2}N{sup −}), triflate (TfO{sup −}), trifluoroacetate (TFA{sup −}), dicyanamide (DCA{sup −}), and thiocyanate (SCN{sup −})). In the ionic liquids studied, the ν{sub 3} center frequency is sensitive to the local solvation environment and reports on the timescales for local structural relaxation. Density functional theory calculations predict charge transfer from the anion to the CO{sub 2} and from CO{sub 2} to the cation. The charge transfer drives geometrical distortion of CO{sub 2}, which in turn changes the ν{sub 3} frequency. The observed structural relaxation timescales vary by up to an order of magnitude between ionic liquids. Shoulders in the 2D-IR spectra arise from anharmonic coupling of the ν{sub 2} and ν{sub 3} normal modes of CO{sub 2}. Thermal fluctuations in the ν{sub 2} population stochastically modulate the ν{sub 3} frequency and generate dynamic cross-peaks. These timescales are attributed to the breakup of ion cages that create a well-defined local environment for CO{sub 2}. The results suggest that the picosecond dynamics of CO{sub 2} are gated by local diffusion of anions and cations.

  13. Determination of eight fluoroquinolones in groundwater samples with ultrasound-assisted ionic liquid dispersive liquid-liquid microextraction prior to high-performance liquid chromatography and fluorescence detection.

    PubMed

    Vázquez, M M Parrilla; Vázquez, P Parrilla; Galera, M Martínez; García, M D Gil

    2012-10-20

    An ultrasound-assisted ionic liquid dispersive liquid-liquid microextraction (US-IL-DLLME) procedure was developed for the extraction of eight fluoroquinolones (marbofloxacin, norfloxacin, ciprofloxacin, lomefloxacin, danofloxacin, enrofloxacin, oxolinic acid and nalidixic acid) in groundwater, using high-performance liquid chromatography with fluorescence detection (HPLC-FD). The ultrasound-assisted process was applied to accelerate the formation of the fine cloudy solution using a small volume of disperser solvent (0.4 mL of methanol), which increased the extraction efficiency and reduced the equilibrium time. For the DLLME procedure, the IL 1-octyl-3-methylimidazolium hexafluorophosphate ([C(8)MIM] [PF(6)]) and methanol (MeOH) were used as extraction and disperser solvent, respectively. By comparing [C(8)MIM] [PF(6)] with 1-hexyl-3-methylimidazolium hexafluorophosphate ([C(6)MIM] [PF(6)]) and 1-butyl-3-methylimidazolium hexafluorophosphate ([C(4)MIM] [PF(6)]) as extraction solvents, it was observed that when using [C(8)MIM] [PF(6)] the cloudy solution was formed more readily than when using [C(6)MIM] [PF(6)] or [C(4)MIM] [PF(6)]. The factors affecting the extraction efficiency, such as the type and volume of ionic liquid, type and volume of disperser solvent, cooling in ice-water, sonication time, centrifuging time, sample pH and ionic strength, were optimised. A slight increase in the recoveries of fluoroquinolones was observed when an ice-water bath extraction step was included in the analytical procedure (85-107%) compared to those obtained without this step (83-96%). Under the optimum conditions, linearity of the method was observed over the range 10-300 ng L(-1) with correlation coefficient >0.9981. The proposed method has been found to have excellent sensitivity with limit of detection between 0.8 and 13 ng L(-1) and precision with relative standard deviation values between 4.8 and 9.4% (RSD, n=5). Good enrichment factors (122-205) and recoveries (85

  14. A Sustainable Approach to the Stereoselective Synthesis of Diazaheptacyclic Cage Systems Based on a Multicomponent Strategy in an Ionic Liquid.

    PubMed

    Suresh Kumar, Raju; Almansour, Abdulrahman I; Arumugam, Natarajan; Altaf, Mohammad; Menéndez, José Carlos; Kumar, Raju Ranjith; Osman, Hasnah

    2016-01-01

    The microwave-assisted three-component reactions of 3,5-bis(E)-arylmethylidene]tetrahydro-4(1H)-pyridinones, acenaphthenequinone and cyclic α-amino acids in an ionic liquid, 1-butyl-3-methylimidazolium bromide, occurred through a domino sequence affording structurally intriguing diazaheptacyclic cage-like compounds in excellent yields. PMID:26840282

  15. Ionic Liquid as a Solvent and Catalyst for Acylation of Maltodextrin

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Catalyst-free esterification of maltodextrin was carried out in ionic liquid. Stearate esters of maltodextrin were obtained in various degree of substitution (DS) when vinyl stearate or stearic acid was heated with maltodextrin in ionic liquid, 1-butyl-3-methylimidazolium cyanamide (bmim[dca]). Re...

  16. Acetylation of Starch with Vinyl Acetate in Imidazolium Ionic Liquids and Characterization of Acetate Distribution

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Starch was acetylated with vinyl acetate in different 1-butyl-3-methylimidazolium (BMIM) salts as solvent in effort to produce starches with different acetylation patterns. Overall degree of substitution was much higher for basic anions such as acetate and dicyanimide (dca) than for neutral anions ...

  17. Ionic liquid-in-oil microemulsions.

    PubMed

    Eastoe, Julian; Gold, Sarah; Rogers, Sarah E; Paul, Alison; Welton, Tom; Heenan, Richard K; Grillo, Isabelle

    2005-05-25

    Phase stability and small-angle neutron scattering (SANS) data show that surfactant-stabilized nanodomains of a typical ionic liquid (1-butyl-3-methylimidazolium tetrafluoroborate [bmim][BF4]) may be dispersed by the nonionic surfactant Triton-X100 in cyclohexane. Analyses of these SANS data are consistent with the formation of ionic liquid-in-oil microemulsion droplets. PMID:15898765

  18. Esterification of Starch in Ionic Liquids

    Technology Transfer Automated Retrieval System (TEKTRAN)

    We shall discuss the use of various ionic liquids in the preparation of starch esters. Starch was reacted with vinyl acetate in different 1-butyl-3-methylimidazolium (bmim) salts as solvents in an effort to produce starches with different acetylation patterns. Overall degree of substitution (DS) w...

  19. Gold-ionic liquid nanofluids with preferably tribological properties and thermal conductivity

    PubMed Central

    2011-01-01

    Gold/1-butyl-3-methylimidazolium hexafluorophosphate (Au/[Bmim][PF6]) nanofluids containing different stabilizing agents were fabricated by a facile one-step chemical reduction method, of which the nanofluids stabilized by cetyltrimethylammonium bromide (CTABr) exhibited ultrahighly thermodynamic stability. The transmission electron microscopy, UV-visible absorption, Fourier transform infrared, and X-ray photoelectron characterizations were conducted to reveal the stable mechanism. Then, the tribological properties of these ionic liquid (IL)-based gold nanofluids were first investigated in more detail. In comparison with pure [Bmim][PF6] and the nanofluids possessing poor stability, the nanofluids with high stability exhibited much better friction-reduction and anti-wear properties. For instance, the friction coefficient and wear volume lubricated by the nanofluid with rather low volumetric concentration (1.02 × 10-3%) stabilized by CTABr under 800 N are 13.8 and 45.4% lower than that of pure [Bmim][PF6], confirming that soft Au nanoparticles (Au NPs) also can be excellent additives for high performance lubricants especially under high loads. Moreover, the thermal conductivity (TC) of the stable nanofluids with three volumetric fraction (2.55 × 10-4, 5.1 × 10-4, and 1.02 × 10-3%) was also measured by a transient hot wire method as a function of temperature (33 to 81°C). The results indicate that the TC of the nanofluid (1.02 × 10-3%) is 13.1% higher than that of [Bmim][PF6] at 81°C but no obvious variation at 33°C. The conspicuously temperature-dependent and greatly enhanced TC of Au/[Bmim][PF6] nanofluids stabilized by CTABr could be attributed to micro-convection caused by the Brownian motion of Au NPs. Our results should open new avenues to utilize Au NPs and ILs in tribology and the high-temperature heat transfer field. PMID:21711789

  20. Rapid ionic liquid-based ultrasound assisted dual magnetic microextraction to preconcentrate and separate cadmium-4-(2-thiazolylazo)-resorcinol complex from environmental and biological samples.

    PubMed

    Khan, Sumaira; Kazi, Tasneem Gul; Soylak, Mustafa

    2014-04-01

    A rapid and innovative microextraction technique named as, ionic liquid-based ultrasound-assisted dual magnetic microextraction (IL-UA-DMME) was developed for the preconcentration and extraction of trace cadmium from environmental and biological samples, prior to analyzed by flame atomic absorption spectrometry (FAAS). The proposed method has many obvious advantages, including evading the use of organic solvents and achieved high extraction yields by the combination of dispersive liquid-liquid microextraction (DLLME) and magnetic mediated-solid phase extraction (MM-SPE). In this approach ionic liquid (IL) 1-butyl-3-methylimidazolium hexafluorophosphate [C4mim][PF6] play an important role to extract the cadmium-4-(2-thiazolylazo)-resorcinol (Cd-TAR) complex from acid digested sample solutions and ultrasonic irradiation was applied to assist emulsification. After then, dispersed small amount of Fe3O4 magnetic nanoparticles (MNPs) in sample solutions to salvaged the IL and complete phase separation was attained. Some analytical parameters that influencing the efficiency of proposed (IL-UA-DMME) method, such as pH, volume of IL, ligand concentration, ultra-sonication time, amount of Fe3O4 MNPs, sample volume and matrix effect were optimized. Limit of detection (LOD) and enrichment factor (EF) of the method under optimal experimental conditions were found to be 0.40μgL(-1) and 100, respectively. The relative standard deviation (RSD) of 50μgL(-1) Cd was 4.29%. The validity and accuracy of proposed method, was assessed to analyzed certified reference materials of fortified lake water TMDA-54.4, SPS-WW2 waste water, spinach leaves 1570a and also checked by standard addition method. The obtained values showed good agreement with the certified values and sufficiently high recovery were found in the range of 98.1-101% for Cd. The proposed method was facile, rapid and successfully applied for the determination of Cd in environmental and different biological samples. PMID

  1. Ionic liquids for nano- and microstructures preparation. Part 2: Application in synthesis.

    PubMed

    Łuczak, Justyna; Paszkiewicz, Marta; Krukowska, Anna; Malankowska, Anna; Zaleska-Medynska, Adriana

    2016-01-01

    Ionic liquids (ILs) are widely applied to prepare metal nanoparticles and 3D semiconductor microparticles. Generally, they serve as a structuring agent or reaction medium (solvent), however it was also demonstrated that ILs can play a role of a co-solvent, metal precursor, reducing as well as surface modifying agent. The crucial role and possible types of interactions between ILs and growing particles have been presented in the Part 1 of this review paper. Part 2 of the paper gives a comprehensive overview of recent experimental studies dealing with application of ionic liquids for preparation of metal and semiconductor based nano- and microparticles. A wide spectrum of preparation routes using ionic liquids is presented, including precipitation, sol-gel technique, hydrothermal method, nanocasting and ray-mediated methods (microwave, ultrasound, UV-radiation and γ-radiation). It was found that ionic liquids formed of a 1-butyl-3-methylimidazolium [BMIM] combined with tetrafluoroborate [BF4], hexafluorophosphate [PF6], and bis(trifluoromethanesulfonyl)imide [Tf2N] are the most often used ILs in the synthesis of nano- and microparticles, due to their low melting temperature, low viscosity and good transportation properties. Nevertheless, examples of other IL classes with intrinsic nanoparticles stabilizing abilities such as phosphonium and ammonium derivatives are also presented. Experimental data revealed that structure of ILs (both anion and cation type) affects the size and shape of formed metal particles, and in some cases may even determine possibility of particles formation. The nature of the metal precursor determines its affinity to polar or nonpolar domains of ionic liquid, and therefore, the size of the nanoparticles depends on the size of these regions. Ability of ionic liquids to form varied extended interactions with particle precursor as well as other compounds presented in the reaction media (water, organic solvents etc.) provides nano- and

  2. Anion effects in the extraction of lanthanide 2-thenoyltrifluoroacetone complexes into an ionic liquid

    SciTech Connect

    Jensen, Mark P.; Beitz, James V.; Rickert, Paul G.; Borkowski, Marian; Laszak, Ivan; Dietz, Mark L.

    2012-07-01

    The extraction of trivalent lanthanides from an aqueous phase containing 1 M NaClO{sub 4} into the room temperature ionic liquid 1-butyl-3-methylimidazolium nonafluoro-1-butane sulfonate by the beta-diketone extractant 2-thenoyltrifluoroacetone (Htta) was studied. Radiotracer distribution, absorption spectroscopy, time-resolved laser-induced fluorescence spectroscopy, and X-ray absorption fine structure measurements point to the extraction of multiple lanthanide species. At low extractant concentrations, fully hydrated aqua cations of the lanthanides are present in the ionic liquid phase. As the extractant concentration is increased 1:2 and 1:3 lanthanide:tta species are observed. In contrast, 1:4 Ln:tta complexes were observed in the extraction of lanthanides by Htta into 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide. (authors)

  3. Ligand-assisted soft-chemical synthesis of self-assembled different shaped mesoporous Co3O4: efficient visible light photocatalysts.

    PubMed

    Roy, Mouni; Ghosh, Sourav; Naskar, Milan Kanti

    2015-04-21

    Mesoporous self-assembled cobalt oxide (Co3O4) of different shapes was synthesized by a facile soft-chemical process using cobalt nitrate, oxalic acid and phosphoric acid in the presence of cationic templates, cetyltrimethylammonium bromide, 1-butyl-3-methylimidazolium bromide, and pyridinium bromide at 75 °C/2 h followed by calcination at 300 °C. The effect of cationic templates of the samples on the physico-chemical properties, and the photocatalytic efficiency for the degradation of Chicago Sky Blue 6B was studied. Pyridinium bromide and 1-butyl-3-methylimidazolium bromide facilitated formation of particles with different shaped morphology compared to cetyltrimethylammonium bromide. The rod-like particles having higher surface area exhibited higher photocatalytic performance. PMID:25792483

  4. Fast Measurement of Methanol Concentration in Ionic Liquids by Potential Step Method

    PubMed Central

    Hainstock, Michael L.; Tang, Yijun

    2015-01-01

    The development of direct methanol fuel cells required the attention to the electrolyte. A good electrolyte should not only be ionic conductive but also be crossover resistant. Ionic liquids could be a promising electrolyte for fuel cells. Monitoring methanol was critical in several locations in a direct methanol fuel cell. Conductivity could be used to monitor the methanol content in ionic liquids. The conductivity of 1-butyl-3-methylimidazolium tetrafluoroborate had a linear relationship with the methanol concentration. However, the conductivity was significantly affected by the moisture or water content in the ionic liquid. On the contrary, potential step could be used in sensing methanol in ionic liquids. This method was not affected by the water content. The sampling current at a properly selected sampling time was proportional to the concentration of methanol in 1-butyl-3-methylimidazolium tetrafluoroborate. The linearity still stood even when there was 2.4 M water present in the ionic liquid. PMID:25802522

  5. Preparation of tamarind gum based soft ion gels having thixotropic properties.

    PubMed

    Sharma, Mukesh; Mondal, Dibyendu; Mukesh, Chandrakant; Prasad, Kamalesh

    2014-02-15

    Tamarind gum was used to prepare ion gels using both synthetic ionic liquids (ILs) namely 1-butyl-3-methylimidazolium chloride and 1-butyl-3-methylimidazolium bromide and bio-based ionic liquids (Bio-ILs) namely choline acrylate, choline caproate and choline caprylate by heating cooling process. The gels were found to have good thermal stability and exhibited thixotropic behaviour. Upon relaxation after applied breaking strain, the recovery of gel structures after ten consecutive cycles was observed. The hydrogel of the gum prepared using ethanol aqueous solution had much inferior quality in terms of viscosity, viscoelasticity, thermal stability and thixotropicity when compared with the ion gels. The ion gels also showed very good adherence to human finger muscles and skin. The ion gels thus prepared may find application in electrochemistry, sensors, actuators and the gels prepared with Bio-ILs could even be useful in biomedical applications. PMID:24507307

  6. Ionic liquids-lithium salts pretreatment followed by ultrasound-assisted extraction of vitexin-4″-O-glucoside, vitexin-2″-O-rhamnoside and vitexin from Phyllostachys edulis leaves.

    PubMed

    Hou, Kexin; Chen, Fengli; Zu, Yuangang; Yang, Lei

    2016-01-29

    An efficient method for the extraction of vitexin, vitexin-4″-O-glucoside, and vitexin-2″-O-rhamnoside from Phyllostachys edulis leaves comprises heat treatment using an ionic liquid-lithium salt mixture (using 1-butyl-3-methylimidazolium bromide as the solvent and lithium chloride as the additive), followed by ultrasound-assisted extraction. To obtain higher extraction yields, the effects of the relevant experimental parameters (including heat treatment temperature and time, relative amounts of 1-butyl-3-methylimidazolium bromide and lithium chloride, power and time of the ultrasound irradiation, and the liquid-solid ratio) are evaluated and response surface methodology is used to optimize the significant factors. The morphologies of the treated and untreated P. edulis leaves are studied by scanning electron microscopy. The improved extraction method proposed provides high extraction yield, good repeatability and precision, and has wide potential applications in the analysis of plant samples. PMID:26763300

  7. Accurate measurements of thermodynamic properties of solutes in ionic liquids using inverse gas chromatography.

    PubMed

    Mutelet, Fabrice; Jaubert, Jean-Noël

    2006-01-13

    Activity coefficients at infinite dilution of 29 organic compounds in two room temperature ionic liquids were determined using inverse gas chromatography. The measurements were carried out at different temperatures between 323.15 and 343.15K. To establish the influence of concurrent retention mechanisms on the accuracy of activity coefficients at infinite dilution for 1-butyl-3-methylimidazolium octyl sulfate and 1-ethyl-3-methylimidazolium tosylate, phase loading studies of the net retention volume per gram of packing as a function of the percent phase loading were used. It is shown that most of the solutes are retained largely by partition with a small contribution from adsorption on 1-butyl-3-methylimidazolium octyl sulfate and that the n-alkanes are retained predominantly by interfacial adsorption on 1-ethyl-3-methylimidazolium tosylate. PMID:16310203

  8. Organo-niobate Ionic Liquids: Synthesis, Characterization and Application as Acid Catalyst in Pechmann Reactions

    PubMed Central

    Soares, Valerio C. D.; Alves, Melquizedeque B.; Souza, Ernesto R.; Pinto, Ivana O.; Rubim, Joel C.; Andrade, Carlos Kleber Z.; Suarez, Paulo A. Z.

    2007-01-01

    The combinations of 1-butyl-3-methylimidazolium chloride with NbCl5 yielded ionic mixtures with different melting point temperatures and acidity depending on the niobium molar fraction. The mixtures were characterized by thermal (DSC) and spectroscopic (FT-IR and 1H NMR) analysis. The Pechmann reactions of different phenols with ethylacetoacetate, producing coumarins, was used as model to evaluate the catalytic behavior of these mixtures as acid Lewis catalyst. These reactions were carried out using acidic mixtures of 60 mol%.

  9. An Expedient Regio- and Diastereoselective Synthesis of Hybrid Frameworks with Embedded Spiro[9,10]dihydroanthracene [9,3']-pyrrolidine and Spiro[oxindole-3,2'-pyrrolidine] Motifs via an Ionic Liquid-Mediated Multicomponent Reaction.

    PubMed

    Arumugam, Natarajan; Almansour, Abdulrahman I; Kumar, Raju Suresh; Menéndez, J Carlos; Sultan, Mujeeb A; Karama, Usama; Ghabbour, Hazem A; Fun, Hoong-Kun

    2015-01-01

    A series of hitherto unreported anthracene-embedded dispirooxindoles has been synthesized via a one-pot three-component 1,3-dipolar cycloaddition reaction of an azomethine ylide, generated in situ from the reaction of isatin and sarcosine to 10-benzylideneanthracen-9(10H)-one as a dipolarophile in 1-butyl-3-methylimidazolium bromide([bmim]Br), an ionic liquid. This reaction proceeded regio- and diastereoselectively, in good to excellent yields. PMID:26404224

  10. Aggregation behavior of 1-dodecyl-3-methylimidazolium bromide in aqueous solution: effect of ionic liquids with aromatic anions.

    PubMed

    Gu, Yingqiu; Shi, Lijuan; Cheng, Xiyuan; Lu, Fei; Zheng, Liqiang

    2013-05-28

    The effects of ionic liquids (ILs), 1-butyl-3-methylimidazolium methylsulfonate (bmimMsa), 1-butyl-3-methylimidazolium benzenesulfonate (bmimBsa), and 1-butyl-3-methylimidazolium 2-naphthalenesulfonate (bmimNsa), on the aggregation behavior of 1-dodecyl-3-methylimidazolium bromide (C12mimBr) in aqueous solution were investigated by surface tension, dynamic light scattering measurements, and (1)H NMR spectroscopy. The ability to promote the surfactant aggregation is in the order bmimNsa > bmimBsa > bmimMsa. Nevertheless, only bmimNsa distinctly reduces both the CMC value and the surface tension at CMC. Due to the penetration of C10H7SO3(-)anions into the surfactant aggregate, bmimNsa is found to induce a phase transition from micelles to vesicles, whereas the other ILs only slightly increase the sizes of micelles. The combined effect of intermolecular interactions, such as hydrophobic effect, electrostatic attractions, and π-π stacking interactions, is supposed to be responsible for this structural transformation, in which π-π stacking plays an important role. PMID:23642150

  11. Spectroscopic properties and amplified spontaneous emission of fluorescein laser dye in ionic liquids as green media

    NASA Astrophysics Data System (ADS)

    AL-Aqmar, Dalal M.; Abdelkader, H. I.; Abou Kana, Maram T. H.

    2015-09-01

    The use of ionic liquids (ILs) as milieu materials for laser dyes is a promising field and quite competitive with volatile organic solvents and solid state-dye laser systems. This paper investigates some photo-physical parameters of fluorescein dye incorporated into ionic liquids; 1-Butyl-3-methylimidazolium chloride (BMIM Cl), 1-Butyl-3-methylimidazolium tetrachloroaluminate (BMIM AlCl4) and 1-Butyl-3-methylimidazolium tetrafluoroborate (BMIM BF4) as promising host matrix in addition to ethanol as reference. These parameters are: absorption and emission cross-sections, fluorescence lifetime and quantum yield, in addition to the transition dipole moment, the attenuation length and oscillator strength were also investigated. Lasing characteristics such as amplified spontaneous emission (ASE), the gain, and the photostability of fluorescein laser dye dissolved in different host materials were assessed. The composition and properties of the matrix of ILs were found that it has great interest in optimizing the laser performance and photostability of the investigated laser dye. Under transverse pumping of fluorescein dye by blue laser diode (450 nm) of (400 mW), the initial ASE for dye dissolved in BMIM AlCl4 and ethanol were decreased to 39% and 36% respectively as time progressed 132 min. Relatively high efficiency and high fluorescence quantum yield (11.8% and 0.82% respectively) were obtained with good photostability in case of fluorescein in BMIM BF4 that was decreased to ∼56% of the initial ASE after continuously pumping with 400 mW for 132 min.

  12. Towards the Rational Design of Nanoparticle Catalysts

    NASA Astrophysics Data System (ADS)

    Dash, Priyabrat

    This research is focused on development of routes towards the rational design of nanoparticle catalysts. Primarily, it is focused on two main projects; (1) the use of imidazolium-based ionic liquids (ILs) as greener media for the design of quasi-homogeneous nanoparticle catalysts and (2) the rational design of heterogeneous-supported nanoparticle catalysts from structured nanoparticle precursors. Each project has different studies associated with the main objective of the design of nanoparticle catalysts. In the first project, imidazolium-based ionic liquids have been used for the synthesis of nanoparticle catalysts. In particular, studies on recyclability, reuse, mode-of-stability, and long-term stability of these ionic-liquid supported nanoparticle catalysts have been done; all of which are important factors in determining the overall "greenness" of such synthetic routes. Three papers have been published/submitted for this project. In the first publication, highly stable polymer-stabilized Au, Pd and bimetallic Au-Pd nanoparticle catalysts have been synthesized in imidazolium-based 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM]PF6) ionic liquid (Journal of Molecular Catalysis A: Chemical, 2008, 286, 114). The resulting nanoparticles were found to be effective and selective quasi-homogeneous catalysts towards a wide-range of hydrogenation reactions and the catalyst solution was reused for further catalytic reactions with minimal loss in activity. The synthesis of very pure and clean ILs has allowed a platform to study the effects of impurities in the imidazolium ILs on nanoparticle stability. In a later study, a new mode of stabilization was postulated where the presence of low amounts of 1-methylimidazole has substantial effects on the resulting stability of Au and Pd-Au nanoparticles in these ILs (Chemical Communications, 2009, 812). In further continuation of this study, a comparative study involving four stabilization protocols for nanoparticle

  13. Solvation free energies in [bmim]-based ionic liquids: Anion effect toward solvation of amino acid side chain analogues

    NASA Astrophysics Data System (ADS)

    Latif, Muhammad Alif Mohammad; Micaêlo, Nuno; Abdul Rahman, Mohd Basyaruddin

    2014-11-01

    Stochastic molecular dynamics simulations were performed to investigate the solvation free energy of 15 neutral amino acid side chain analogues in aqueous and five, 1-butyl-3-methylimidazolium ([BMIM])-based ionic liquids. The results in aqueous were found highly correlated with previous experimental and simulation data. Meanwhile, [BMIM]-based RTILs showed better solvation thermodynamics than water to an extent that they were capable of solvating molecules immiscible in water. Non-polar analogues showed stronger solvation in hydrophobic RTIL anions such as [PF6]- and [Tf2N]- while polar analogues showed stronger solvation in the more hydrophilic RTIL anions such as [Cl]-, [TfO]- and [BF4]-.

  14. Microwave-assisted rapid conversion of carbohydrates into 5-hydroxymethylfurfural by ScCl3 in ionic liquids.

    PubMed

    Zhou, Xuanmu; Zhang, Zehui; Liu, Bing; Xu, Zheng; Deng, Kejian

    2013-06-28

    In this study, synthesis of HMF from carbohydrates was carried out in ionic liquids 1-butyl-3-methylimidazolium chloride ([Bmim]Cl) catalyzed by ScCl3 under microwave irradiation. Under the optimal reaction conditions, HMF was obtained in a high yield of 73.4% in 2 mins with the microwave power at 400 W. Compared with the conventional oil-bath heating manner, the use of microwave irradiation not only reduced reaction times from hours to minutes, but also improved HMF yield. This catalytic system could be reused several times without losing its catalytic activity. This efficient catalytic system will generate a promising application strategy for biomass transformation. PMID:23694706

  15. Fabrication and Characterization of Polysaccharide Ion Gels with Ionic Liquids and Their Further Conversion into Value-Added Sustainable Materials

    PubMed Central

    Takada, Akihiko; Kadokawa, Jun-ichi

    2015-01-01

    A review of the fabrication of polysaccharide ion gels with ionic liquids is presented. From various polysaccharides, the corresponding ion gels were fabricated through the dissolution with ionic liquids. As ionic liquids, in the most cases, 1-butyl-3-methylimidazolium chloride has been used, whereas 1-allyl-3methylimidazolium acetate was specifically used for chitin. The resulting ion gels have been characterized by suitable analytical measurements. Characterization of a pregel state by viscoelastic measurement provided the molecular weight information. Furthermore, the polysaccharide ion gels have been converted into value-added sustainable materials by appropriate procedures, such as exchange with other disperse media and regeneration. PMID:25793912

  16. Lithium ion conductive behavior of TiO2 nanotube/ionic liquid matrices

    PubMed Central

    2014-01-01

    A series of TiO2 nanotube (TNT)/ionic liquid matrices were prepared, and their lithium ion conductive properties were studied. SEM images implied that ionic liquid was dispersed on the whole surface of TNT. Addition of TNT to ionic liquid (1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)amide (BMImTFSA)) resulted in significant increase of ionic conductivity. Furthermore, lithium transference number was also largely enhanced due to the interaction of anion with TNT. Vogel-Fulcher-Tammann parameter showed higher carrier ion number for TNT/BMImTFSA in comparison with BMImTFSA. PMID:25313300

  17. Furfural production in biphasic media using an acidic ionic liquid as a catalyst.

    PubMed

    Peleteiro, Susana; Santos, Valentín; Parajó, Juan C

    2016-11-20

    Ionic liquids are valuable tools for biorefineries. This study provides an experimental assessment on the utilization of an acidic ionic liquid (1-butyl-3-methylimidazolium hydrogen sulfate) as a catalyst for furfural production in water/solvent media. The substrates employed in experiments were commercial xylose (employed as a reference compound) or hemicellulosic saccharides obtained by hydrothermal processing of Eucalyptus globulus wood (which were employed as produced, after membrane concentration or after freeze-drying). A variety of reaction conditions (defined by temperature, reaction time and type of organic solvent) were considered. The possibility of recycling the catalyst was assessed in selected experiments. PMID:27561513

  18. Lipid extraction from microalgae using a single ionic liquid

    DOEpatents

    Salvo, Roberto Di; Reich, Alton; Dykes, Jr., H. Waite H.; Teixeira, Rodrigo

    2013-05-28

    A one-step process for the lysis of microalgae cell walls and separation of the cellular lipids for use in biofuel production by utilizing a hydrophilic ionic liquid, 1-butyl-3-methylimidazolium. The hydrophilic ionic liquid both lyses the microalgae cell walls and forms two immiscible layers, one of which consists of the lipid contents of the lysed cells. After mixture of the hydrophilic ionic liquid with a suspension of microalgae cells, gravity causes a hydrophobic lipid phase to move to a top phase where it is removed from the mixture and purified. The hydrophilic ionic liquid is recycled to lyse new microalgae suspensions.

  19. Solvent extraction separation of Th-227 and Ac-225 in room temperature ionic liquids

    SciTech Connect

    Bell, Jason R; Boll, Rose Ann; Dai, Sheng; Luo, Huimin

    2012-01-01

    The solvent extractions of Th-227 and Ac-225 from the aqueous phase into ionic liquids (ILs) were investigated by using N,N,N ,N - tetraoctyldiglycolamide (TODGA) or di(2-ethylhexyl)phosphoric acid (HDEHP) as an extractant. Four ionic liquids, 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([C4mim][NTf2]), 1-butyl-3-methylimidazolium bis(perfluoroethanesulfonyl)imide ([C4mim][BETI]), 1-butyl-2,3-trimethyleneimidazolium (trifluoromethanesulfonyl)imide [BuI5][NTf2], and 1-benzyl pyridinium bis(trifluoromethanesulfonyl)imide ([PhCH2Py][NTf2]) were used as extraction solvents for separation of Th-227 and Ac-225 in this study. Excellent extraction efficiencies and selectivities were found for Th-227/Ac-225 when HDEHP was used as an extractant in these ionic liquids. The effects of different extractant concentrations in ionic liquids and acidities of the aqueous phase on extraction efficiencies and selectivities of Th-227/Ac-225 are also presented in this article.

  20. Functionalized Agarose Self-Healing Ionogels Suitable for Supercapacitors.

    PubMed

    Trivedi, Tushar J; Bhattacharjya, Dhrubajyoti; Yu, Jong-Sung; Kumar, Arvind

    2015-10-12

    Agarose has been functionalized (acetylated/carbanilated) in an ionic liquid (IL) medium of 1-butyl-3-methylimidazolium acetate at ambient conditions. The acetylated agarose showed a highly hydrophobic nature, whereas the carbanilated agarose could be dissolved in water as well as in the IL medium. Thermoreversible ionogels were obtained by cooling the IL sols of carbanilated agarose at room temperature. The ionogel prepared from a protic-aprotic mixed-IL system (1-butyl-3-methylimidazolium chloride and N-(2-hydroxyethyl)ammonium formate) demonstrated a superior self-healing property, as confirmed from rheological measurements. The superior self-healing property of such an ionogel has been attributed to the unique inter-intra hydrogen-bonding network of functional groups inserted in the agarose. The ionogel was tested as a flexible solid electrolyte for an activated-carbon-based supercapacitor cell. The measured specific capacitance was found to be comparable with that of a liquid electrolyte system at room temperature and was maintained for up to 1000 charge-discharge cycles. Such novel functionalized-biopolymer self-healing ionogels with flexibility and good conductivity are desirable for energy-storage devices and electronic skins with superior lifespans and robustness. PMID:26280813

  1. Heats of vaporization of room temperature ionic liquids by tunable vacuum ultraviolet photoionization

    SciTech Connect

    Chambreau, Steven D.; Vaghjiani, Ghanshyam L.; To, Albert; Koh, Christine; Strasser, Daniel; Kostko, Oleg; Leone, Stephen R.

    2009-11-25

    The heats of vaporization of the room temperature ionic liquids (RTILs) N-butyl-N-methylpyrrolidinium bistrifluorosulfonylimide, N-butyl-N-methylpyrrolidinium dicyanamide, and 1-butyl-3-methylimidazolium dicyanamide are determined using a heated effusive vapor source in conjunction with single photon ionization by a tunable vacuum ultraviolet synchrotron source. The relative gas phase ionic liquid vapor densities in the effusive beam are monitored by clearly distinguished dissociative photoionization processes via a time-of-flight mass spectrometer at a tunable vacuum ultraviolet beamline 9.0.2.3 (Chemical Dynamics Beamline) at the Advanced Light Source synchrotron facility. Resulting in relatively few assumptions, through the analysis of both parent cations and fragment cations, the heat of vaporization of N-butyl-N-methylpyrrolidinium bistrifluorosulfonylimide is determined to be Delta Hvap(298.15 K) = 195+-19 kJ mol-1. The observed heats of vaporization of 1-butyl-3-methylimidazolium dicyanamide (Delta Hvap(298.15 K) = 174+-12 kJ mol-1) and N-butyl-N-methylpyrrolidinium dicyanamide (Delta Hvap(298.15 K) = 171+-12 kJ mol-1) are consistent with reported experimental values using electron impact ionization. The tunable vacuum ultraviolet source has enabled accurate measurement of photoion appearance energies. These appearance energies are in good agreement with MP2 calculations for dissociative photoionization of the ion pair. These experimental heats of vaporization, photoion appearance energies, and ab initio calculations corroborate vaporization of these RTILs as intact cation-anion ion pairs.

  2. High carbon dioxide solubilities in imidazolium-based ionic liquids and in poly(ethylene glycol) dimethyl ether.

    PubMed

    Revelli, Anne-Laure; Mutelet, Fabrice; Jaubert, Jean-Noël

    2010-10-14

    This work is focused on the possible capture of carbon dioxide using ionic liquids (ILs). Such solvents are gaining special attention because the efficiency of many processes can be enhanced by the judicious manipulation of their properties. The absorption of greenhouse gases can be enhanced by the basic character of the IL. In this work, these characteristics are evaluated through the study of the gas-liquid equilibrium of four imidazolium-based ILs: 1-butyl-3-methylimidazolium tetrafluoroborate [BMIM][BF(4)], 1-butyl-3-methylimidazolium thiocyanate [BMIM][SCN], 1,3-dimethylimidazolium methylphosphonate [DMIM][MP], and 1,3-diethoxyimidazolium bis(trifluoromethylsulfonyl)imide [(ETO)(2)IM][Tf(2)N] with CO(2) at temperatures up to 373 K and pressures up to 300 bar. Solubility of carbon dioxide in poly(ethylene glycol) dimethyl ether, component of selexol, was also measured to evaluate the capture's efficiency of ionic liquids. Experimental data indicate that 67 to 123 g of CO(2) can be absorbed per kg of ionic liquid and 198 g per kg of poly(ethylene glycol) dimethyl ether. PMID:20853857

  3. Alkylation of Methyl Linoleate with Propene in Ionic Liquids in the Presence of Metal Salts.

    PubMed

    Pomelli, Christian Silvio; Ghilardi, Tiziana; Chiappe, Cinzia; de Angelis, Alberto Renato; Calemma, Vincenzo

    2015-01-01

    Vegetable oils and fatty acid esters are suitable precursor molecules for the production of a variety of bio-based products and materials, such as paints and coatings, plastics, soaps, lubricants, cosmetics, pharmaceuticals, printing inks, surfactants, and biofuels. Here, we report the possibility of using Lewis acidic ionic liquids (ILs) to obtain polyunsaturated ester dimerization-oligomerization and/or, in the presence of another terminal alkene (propene), co-polymerization. In particular, we have tested the Lewis acidic mixtures arising from the addition of a proper amount of GaCl₃ (Χ > 0.5) to two chloride-based (1-butyl-3-methylimidazolium chloride, [bmim]Cl, and 1-butylisoquinolium chloride, [BuIsoq]Cl) or by dissolution of a smaller amount of Al(Tf₂N)₃ (Χ = 0.1) in 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, [bmim][Tf₂N]. On the basis of product distribution studies, [bmim][Tf₂N]/Al(Tf₂N)₃ appears the most suitable medium in which methyl linoleate alkylation with propene can compete with methyl linoleate or propene oligomerization. PMID:26690107

  4. On the formation of new reverse micelles: a comparative study of benzene/surfactants/ionic liquids systems using UV-visible absorption spectroscopy and dynamic light scattering.

    PubMed

    Falcone, R Darío; Correa, N Mariano; Silber, Juana J

    2009-09-15

    The microenvironment of the polar core generated in different ionic liquid reverse micelle (IL RM) systems were investigated using the solvatochromic behavior of 1-methyl-8-oxyquinolinium betaine (QB) as an absorption probe and dynamic light scattering (DLS) technique. The novel RM systems consist of two different ILs--1-butyl-3-methylimidazolium tetrafluoroborate (bmimBF4) and 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (bmimTf2N)--sequestrated by two different surfactants--Triton X-100 (TX-100) and benzyl-n-hexadecyldimethylammonium chloride (BHDC)--in order to make IL/surfactant/benzene RMs. The effect of the variation of Ws (Ws=[IL]/[surfactant]) on the QB spectroscopy was used to characterize these nonaqueous RMs. DLS results confirm the formation of these IL RM systems because increasing Ws increases the droplet sizes. Moreover it is demonstrated that the structure of the sequestrated ILs depends strongly on the type of surfactant use to create the RMs. PMID:19678620

  5. Lignin dissolution in dialkylimidazolium-based ionic liquid-water mixtures.

    PubMed

    Wang, Yantao; Wei, Ligang; Li, Kunlan; Ma, Yingchong; Ma, Ningning; Ding, Shan; Wang, Linlin; Zhao, Deyang; Yan, Bing; Wan, Wenying; Zhang, Qian; Wang, Xin; Wang, Junmei; Li, Hui

    2014-10-01

    Lignin dissolution in dialkylimidazolium-based ionic liquid (IL)-water mixtures (40wt%-100wt% IL content) at 60°C was investigated. The IL content and type are found to considerably affect lignin solubility. For the IL-water mixtures except 1-butyl-3-methylimidazolium tetrafluoroborate ([C4C1im]BF4), the maximum lignin solubility can be achieved at 70wt% IL content. Lignin solubility in IL-water mixtures with different cations follows the order 1-butyl-3-methylimidazolium ([C4C1im](+))>1-hexyl-3-methylimidazolium ([C6C1im](+))>1-ethyl-3-methylimidazolium ([C2C1im](+))>1-octyl-3-methylimidazolium ([C8C1im](+))>1-butyl-3-ethylimidazolium ([C4C2im](+))>1-butyl-3-propylimidazolium ([C4C3im](+)). For IL mixtures with different anions, lignin solubility decreases in the following order: methanesulfonate (MeSO3(-))>acetate (MeCO2(-))>bromide (Br(-))>dibutylphosphate (DBP(-)). Evaluation using the theory of Hansen solubility parameter (HSP) is consistent with the experimental results, suggesting that HSP can aid in finding the appropriate range of IL content for IL-water mixtures. However, HSP cannot be used to evaluate the effect of IL type on lignin solubility. PMID:25164342

  6. Neural networks to estimate the water content of imidazolium-based ionic liquids using their refractive indices.

    PubMed

    Torrecilla, José S; Tortuero, César; Cancilla, John C; Díaz-Rodríguez, Pablo

    2013-11-15

    A non-linear model has been developed to estimate the water content of 1-butyl-3-methylimidazolium tetrafluoroborate, 1-butyl-3-methylimidazolium methylsulfate, and 1,3-dimethylimidazolium methylsulfate ionic liquids using their respective refractive index values. The experimental values measured to design the neural network (NN) model were registered at 298.15K. These were determined at different relative humidity values which ranged from 11.1% to 84.3%. The estimated results were compared with experimental measurements of water content obtained by the Karl Fischer technique, and the differences between the real and estimated values were less than 0.06% in the internal validation process. In addition, an external validation test was developed using bibliographical references. In this case, the mean prediction error was less than 5.4%. In light of these results, the NN model shows an acceptable goodness of fit, sufficient robustness, and a more than adequate predictive capacity to estimate the water content of the ILs through the analysis of their refractive index. PMID:24148382

  7. Microwave-assisted synthesis of gold, silver, platinum and palladium nanostructures and their use in electrocatalytic applications.

    PubMed

    Safavi, Afsaneh; Tohidi, Maryam

    2014-09-01

    Microwave-assisted ionic liquid method was used for synthesis of various noble metals, such as gold, silver, platinum and palladium nanomaterials. This route does not employ any template agent, surface capping agents or reducing agents. The process is fast, simple and of high yield. Different metal precursors in various ionic liquids media (1-butyl-3-methylimidazolium tetrafluoroborate, octyl pyridinium hexaflurophosphate and 1-octyl-3-methylimidazolium hexaflurophosphate) were applied to produce metal nanomaterials. Silver, platinium and palladium nanoparticles exhibit spherical morphology while nanosheets with high aspect ratio were obtained for gold. These metal nanostructures were incorporated into a carbon ionic liquid electrode to investigate their electrocatalytic properties. It was found that synthesis in different ionic liquids result in different activity. Excellent electrocatalytic effects toward adenine, hydrazine, formaldehyde and ethanol were observed for the modified electrodes with different nanoparticles synthesized in 1-butyl-3-methylimidazolium tetrafluoroborate. The high conductivity, large surface-to-volume ratio and active sites of nanosized metal particles are responsible for their electrocatalytic activity. In contrast, the carbon ionic liquid electrode modified with synthesized metal nanoparticles in octyl pyridinium hexaflurophosphate and 1-octyl-3-methylimidazolium hexaflurophosphate showed negligible activity for detection of these probes. PMID:25924389

  8. Radiolysis of solutions of diphenyliodonium and triphenylsulfonium hexafluorophosphates in various solvents

    SciTech Connect

    Ma, X.H.; Yamamoto, Y.; Hayashi, K.

    1988-11-11

    The radiolysis of solutions of Ph/sub 2/IPF/sub 6/ and Ph/sub 3/SPF/sub 6/ was undertaken in various kinds of solvents such as alcohols, ethers, acetone, acetonitrile, and dichloromethane. The salts decompose through one-electron reduction in all of the solvents except dichloromethane. The ..cap alpha..-hydroxyalkyl and ..cap alpha..-alkoxyalkyl radicals derived from the oxygen-containing solvents are oxidized by Ph/sub 2/IPF/sub 6/ to initiate a chain reaction. The kinetic chain length depends on the oxidation potentials of the radicals. In dichloromethane, which is electron scavenger, the decomposition of the salts is much less pronounced than in the other solvents. 41 references, 2 tables, 1 figure.

  9. Morphology-controlled synthesis of nanostructured zinc hydroxide fluoride via a microwave-assisted ionic liquid route

    NASA Astrophysics Data System (ADS)

    Zhang, Songtao; Zheng, Mingbo; Song, Jiakui; Li, Nianwu; Lu, Hongling; Cao, Jieming

    2014-12-01

    Zinc hydroxide fluoride (Zn(OH)F) with multiform morphologies such as flower-like particles, pumpkin-like aggregates, and hollow orange-like aggregates are prepared by a microwave-assisted ionic liquid method. During synthesis, microwave irradiation accelerates the reaction rate and shortens the reaction time. 1-Butyl-3-methylimidazolium tetrafluoroborate ([Bmim][BF4]) or 1-2-hydroxylethyl-3-methylimidazolium tetrafluoroborate ([C2OHmim][BF4]) is used as both reactant and template. Experimental results indicate that the morphology evolution of Zn(OH)F is mainly controlled by the concentration of zinc acetate solution. A possible mechanism underlying the formation of nanostructured Zn(OH)F with diverse morphologies is proposed. Furthermore, nanoporous ZnO is obtained by the thermal decomposition of as-prepared Zn(OH)F in air, and the morphology is well retained.

  10. Ionic liquid-based aqueous two-phase system, a sample pretreatment procedure prior to high-performance liquid chromatography of opium alkaloids.

    PubMed

    Li, Shehong; He, Chiyang; Liu, Huwei; Li, Kean; Liu, Feng

    2005-11-01

    An ionic liquid, 1-butyl-3-methylimidazolium chloride ([C4 mim]Cl)/salt aqueous two-phase systems (ATPS) was presented as a simple, rapid and effective sample pretreatment technique coupled with high-performance liquid chromatography (HPLC) for analysis of the major opium alkaloids in Pericarpium papaveris. To find optimal conditions, the partition behaviors of codeine and papaverine in ionic liquid/salt aqueous two-phase systems were investigated. Various factors were considered systematically, and the results indicated that both the pH value and the salting-out ability of salt had great influence on phase separation. The recoveries of codeine and papaverine were 90.0-100.2% and 99.3-102.0%, respectively, from aqueous samples of P. papaveris by the proposed method. PMID:16143571

  11. Spontaneous encapsulation behavior of ionic liquid into carbon nanotube.

    PubMed

    Jiang, Yanyan; Zhang, Kun; Li, Hui; He, Yezeng; Song, Xigui

    2012-11-21

    Molecular dynamics simulations and density functional theory have been performed to investigate the spontaneous encapsulation of 1-butyl-3-methylimidazolium chloride ([Bmim][Cl]) into single-walled carbon nanotubes (SWCNTs). This phenomenon can be attributed to the van der Waals attractive force, hydrogen bonds and especially the π-π stacking effect. The [Bmim][Cl] molecules enter SWCNTs with larger diameters more rapidly, showing an interesting dependence on tube size. A high temperature is not beneficial to, and may even disrupt, the encapsulation of the [Bmim][Cl] molecules. It is also worth noting that the graphene nanoribbon entering the SWCNT would have an extremely different effect on this encapsulation process from when they wrap around the outer surface. Furthermore, the [Bmim][Cl] molecules can assist water transport in the SWCNT by expelling water molecules from the SWCNT. The proposed discoveries eventually provide a powerful way to fabricate nanoscale materials and devices and tune their properties. PMID:23051856

  12. Fabrication of normally-off AlGaN/GaN metal–insulator–semiconductor high-electron-mobility transistors by photo-electrochemical gate recess etching in ionic liquid

    NASA Astrophysics Data System (ADS)

    Zhang, Zhili; Qin, Shuangjiao; Fu, Kai; Yu, Guohao; Li, Weiyi; Zhang, Xiaodong; Sun, Shichuang; Song, Liang; Li, Shuiming; Hao, Ronghui; Fan, Yaming; Sun, Qian; Pan, Gebo; Cai, Yong; Zhang, Baoshun

    2016-08-01

    We characterized an ionic liquid (1-butyl-3-methylimidazolium nitrate, C8H15N3O3) as a photo-electrochemical etchant for fabricating normally-off AlGaN/GaN metal–insulator–semiconductor high-electron-mobility transistors (MIS-HEMTs). Using the ionic liquid, we achieved an etching rate of ∼2.9 nm/min, which is sufficiently low to facilitate good etching control. The normally-off AlGaN/GaN MIS-HEMT was fabricated with an etching time of 6 min, with the 20 nm low-pressure chemical vapor deposition (LPCVD) silicon nitride (Si3N4) gate dielectric exhibiting a threshold voltage shift from ‑10 to 1.2 V, a maximum drain current of more than 426 mA/mm, and a breakdown voltage of 582 V.

  13. Furfural production from Eucalyptus wood using an Acidic Ionic Liquid.

    PubMed

    Peleteiro, Susana; Santos, Valentín; Garrote, Gil; Parajó, Juan Carlos

    2016-08-01

    Eucalyptus globulus wood samples were treated with hot, compressed water to separate hemicelluloses (as soluble saccharides) from a solid phase mainly made up of cellulose and lignin. The liquid phase was dehydrated, and the resulting solids (containing pentoses as well as poly- and oligo- saccharides made up of pentoses) were dissolved and reacted in media containing an Acidic Ionic Liquid (1-butyl-3-methylimidazolium hydrogen sulfate) and a co-solvent (dioxane). The effects of the reaction time on the product distribution were studied at temperatures in the range 120-170°C for reaction times up to 8h, and operational conditions leading to 59.1% conversion of the potential substrates (including pentoses and pentose structural units in oligo- and poly- saccharides) into furfural were identified. PMID:27112846

  14. Nacre-like calcium carbonate controlled by ionic liquid/graphene oxide composite template.

    PubMed

    Yao, Chengli; Xie, Anjian; Shen, Yuhua; Zhu, Jinmiao; Li, Hongying

    2015-06-01

    Nacre-like calcium carbonate nanostructures have been mediated by an ionic liquid (IL)-graphene oxide (GO) composite template. The resultant crystals were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FT-IR) spectroscopy, and X-ray powder diffractometry (XRD). The results showed that either 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM]BF4) or graphene oxide can act as a soft template for calcium carbonate formation with unusual morphologies. Based on the time-dependent morphology changes of calcium carbonate particles, it is concluded that nacre-like calcium carbonate nanostructures can be formed gradually utilizing [BMIM]BF4/GO composite template. During the process of calcium carbonate formation, [BMIM]BF4 acted not only as solvents but also as morphology templates for the fabrication of calcium carbonate materials with nacre-like morphology. Based on the observations, the possible mechanisms were also discussed. PMID:25842135

  15. Preparation and characterisation of high-density ionic liquids incorporating halobismuthate anions.

    PubMed

    Cousens, Nico E A; Taylor Kearney, Leah J; Clough, Matthew T; Lovelock, Kevin R J; Palgrave, Robert G; Perkin, Susan

    2014-07-28

    A range of ionic liquids containing dialkylimidazolium cations and halobismuthate anions ([BiBr(x)Cl(y)I(z)](-) and [Bi2Br(x)Cl(y)I(z)](-)) were synthesised by combining dialkylimidazolium halide ionic liquids with bismuth(III) halide salts. The majority were room temperature liquids, all with very high densities. The neat ionic liquids and their mixtures with 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide were characterised using Densitometry, Viscometry, NMR Spectroscopy, Electrospray Ionisation Mass Spectrometry (ESI), Liquid Secondary Ion Mass Spectrometry (LSIMS), Matrix-assisted Laser Desorption/Ionization Mass Spectrometry (MALDI), X-Ray Photoelectron Spectroscopy (XPS) and Thermogravimetric Analysis (TGA), to establish their speciation and suitability for high-temperature applications. PMID:24898158

  16. The accurate estimation of physicochemical properties of ternary mixtures containing ionic liquids via artificial neural networks.

    PubMed

    Cancilla, John C; Díaz-Rodríguez, Pablo; Matute, Gemma; Torrecilla, José S

    2015-02-14

    The estimation of the density and refractive index of ternary mixtures comprising the ionic liquid (IL) 1-butyl-3-methylimidazolium tetrafluoroborate, 2-propanol, and water at a fixed temperature of 298.15 K has been attempted through artificial neural networks. The obtained results indicate that the selection of this mathematical approach was a well-suited option. The mean prediction errors obtained, after simulating with a dataset never involved in the training process of the model, were 0.050% and 0.227% for refractive index and density estimation, respectively. These accurate results, which have been attained only using the composition of the dissolutions (mass fractions), imply that, most likely, ternary mixtures similar to the one analyzed, can be easily evaluated utilizing this algorithmic tool. In addition, different chemical processes involving ILs can be monitored precisely, and furthermore, the purity of the compounds in the studied mixtures can be indirectly assessed thanks to the high accuracy of the model. PMID:25583241

  17. Cryogenic neon matrix-isolation FTIR spectroscopy of evaporated ionic liquids: geometrical structure of cation-anion 1:1 pair in the gas phase.

    PubMed

    Akai, Nobuyuki; Parazs, David; Kawai, Akio; Shibuya, Kazuhiko

    2009-04-01

    Low-temperature infrared spectra of thermally evaporated ionic liquids, 1-ethyl- and 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide and bis(trifluoromethanesulfonyl)amide have been measured in a cryogenic Ne matrix. The experimental IR spectrum of bis(trifluoromethanesulfonyl)amide can be reproduced theoretically by not B3LYP/6-31G* but MP2/6-31G* calculation, which suggests that the vibrational analysis for ionic liquids composed of bis(trifluoromethanesulfonyl)imide anion would be more successfully performed using the MP2 calculation. By comparison of the matrix-isolation spectra of the ionic liquids with the MP2 calculation, their geometrical structures in the gas phase are determined to be of C(2-position)-H(+)...N(-) interaction structure, which corresponds to the geometry of the energetically second-lowest ion-pair structure. The present study may provide a valuable clue to understand a vaporization mechanism of ionic liquid. PMID:19281187

  18. Preparation of polyhedral oligomeric silsesquioxane based imprinted monolith.

    PubMed

    Li, Fang; Chen, Xiu-Xiu; Huang, Yan-Ping; Liu, Zhao-Sheng

    2015-12-18

    Polyhedral oligomeric silsesquioxane (POSS) was successfully applied, for the first time, to prepare imprinted monolithic column with high porosity and good permeability. The imprinted monolithic column was synthesized with a mixture of PSS-(1-Propylmethacrylate)-heptaisobutyl substituted (MA 0702), naproxon (template), 4-vinylpyridine, and ethylene glycol dimethacrylate, in ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM]BF4). The influence of synthesis parameters on the retention factor and imprinting effect, including the amount of MA 0702, the ratio of template to monomer, and the ratio of monomer to crosslinker, was investigated. The greatest imprinting factor on the imprinted monolithic column prepared with MA 0702 was 22, about 10 times higher than that prepared in absence of POSS. The comparisons between MIP monoliths synthesized with POSS and without POSS were made in terms of permeability, column efficiency, surface morphology and pore size distribution. In addition, thermodynamic and Van Deemter analysis were used to evaluate the POSS-based MIP monolith. PMID:26627587

  19. Hydrolysis of polycarbonate catalyzed by ionic liquid [Bmim][Ac].

    PubMed

    Song, Xiuyan; Liu, Fusheng; Li, Lei; Yang, Xuequn; Yu, Shitao; Ge, Xiaoping

    2013-01-15

    Hydrolysis of polycarbonate (PC) was studied using ionic liquid 1-butyl-3-methylimidazolium acetate ([Bmim][Ac]) as a catalyst. The influences of temperature, time, water dosage and [Bmim][Ac] dosage on the hydrolysis reaction were examined. Under the conditions of temperature 140°C, reaction time 3.0 h, m([Bmim][Ac]):m(PC)=1.5:1 and m(H(2)O):m(PC)=0.35:1, the conversion of PC was nearly 100% and the yield of bisphenol A (BPA) was over 96%. The ionic liquid could be reused up to 6 times without apparent decrease in the conversion of PC and yield of BPA. The kinetics of the reaction was also investigated. The results showed that the hydrolysis of PC in [Bmim][Ac] was a first-order kinetic reaction with an activation energy of 228 kJ/mol. PMID:23246956

  20. Two-dimensional ultrafast vibrational spectroscopy of azides in ionic liquids reveals solute-specific solvation.

    PubMed

    Dutta, Samrat; Ren, Zhe; Brinzer, Thomas; Garrett-Roe, Sean

    2015-10-28

    The stereochemistry and the reaction rates of bimolecular nucleophilic substitution reactions involving azides in ionic liquids are governed by solute-solvent interactions. Two-dimensional ultrafast vibrational spectroscopy (2D-IR) shows that the picosecond dynamics of inorganic azides are substantially slower than organic azides in a series of homologous imidazolium ionic liquids. In water, both organic and inorganic azides spectrally diffuse with a ∼2 ps time constant. In the aprotic solvent tetrahydrofuran, both kinds of azides spectrally diffuse on a timescale >5 ps. In ionic liquids, like 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM][BF4]), organic azides spectrally diffuse with a 2-4 ps time constant, and inorganic azides spectrally diffuse with a >40 ps time constant. Such a striking difference suggests that neutral (organic) and charged (inorganic) azides are incorporated in the ionic liquids with different solvation structures. PMID:26193916

  1. The first molecular level monitoring of carbohydrate conversion to 5-hydroxymethylfurfural in ionic liquids. B2O3--an efficient dual-function metal-free promoter for environmentally benign applications.

    PubMed

    Khokhlova, Elena A; Kachala, Vadim V; Ananikov, Valentine P

    2012-04-01

    The mechanistic nature of the conversion of carbohydrates to the sustainable platform chemical 5-hydroxymethylfurfural (5-HMF) was revealed at the molecular level. A detailed study of the key sugar units involved in the biomass conversion process has shown that the simple dissolution of fructose in the ionic liquid 1-butyl-3-methylimidazolium chloride significantly changes the anomeric composition and favors the formation of the open fructoketose form. A special NMR approach was developed for the determination of molecular structures and monitoring of chemical reactions directly in ionic liquids. The transformation of glucose to 5-HMF has been followed in situ through the detection of intermediate species. A new environmentally benign, easily available, metal-free promoter with a dual functionality (B(2)O(3)) was developed for carbohydrate conversion to 5-HMF. PMID:22359390

  2. The microheterogeneous structure of ionic liquid mixtures with organic solvent determined by a cyanine-dye fluorescent probe

    NASA Astrophysics Data System (ADS)

    Ivanov, Denis A.; Petrov, Nikolai Kh.; Klimchuk, Olga; Billard, Isabelle

    2012-11-01

    The photophysics of 3,3'-diethylthiacarbocyanine iodide (DTCI), as a fluorescence probe, in liquid mixtures of dimethyl sulfoxide (DMSO) with either trimethyl(butyl)ammonium bis((trifluoromethyl)sulfonyl)imide ([N(4)111] [Tf2N]) or 1-butyl-3-methylimidazolium bis((trifluoromethyl)sulfonyl)imide ([bmim] [Tf2N]) was studied by means of steady-state and time resolved fluorescence spectroscopy. The DTCI fluorescence decay was found to be double-exponential in mixtures with [N(4)111] [Tf2N] for DMSO volume fractions less than ca. 0.6 while that is single-exponential in mixtures with [bmim] [Tf2N] under the same conditions. These findings are explained in terms of the Hildebrand solubility model by assuming the existence of coursed-grained spatial micro-heterogeneities in ammonium-based ionic liquid/DMSO mixtures.

  3. Synergistic effects of surfactant-assisted ionic liquid pretreatment rice straw.

    PubMed

    Chang, Ken-Lin; Chen, Xi-Mei; Han, Ye-Ju; Wang, Xiao-Qin; Potprommanee, Laddawan; Ning, Xun-An; Liu, Jing-Yong; Sun, Jian; Peng, Yen-Ping; Sun, Shui-Yu; Lin, Yuan-Chung

    2016-08-01

    The aim of this work was to study an environmentally friendly method for pretreating rice straw by using 1-butyl-3-methylimidazolium chloride ([BMIM]Cl) as an ionic liquid (IL) assisted by surfactants. Different temperatures, reaction times, and surfactant concentrations were studied. Compared with [BMIM]Cl only pretreatment, the addition of 1% sodium dodecyl sulfate (SDS) and 1% cetyl trimethyl ammonium bromide (CTAB) increased lignin removal to 49.48% and 34.76%, respectively. Untreated and pretreated rice straw was thoroughly characterized through FTIR, XRD, and FE-SEM. Cellulose crystallinity and surface morphology of the rice straw were substantially altered after surfactant-assisted IL pretreatment. In conclusion, surfactant-assisted IL pretreatment is an effective method for producing fermentable sugars from lignocellulosic substrates. PMID:27155265

  4. Poly(ethylene oxide) Mushrooms Adsorbed at Silica-Ionic Liquid Interfaces Reduce Friction.

    PubMed

    Sweeney, James; Webber, Grant B; Atkin, Rob

    2016-03-01

    The adsorbed layer conformation and lubricity of 35, 100, and 300 kDa PEO adsorbed to ionic liquid (IL)-silica interfaces from 0.01 wt % solutions have been investigated using colloid probe atomic force microscopy. The ILs used were propylammonium nitrate (PAN) and 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM][BF4]), which are protic and aprotic ILs, respectively. Normal force curves reveal steric interactions consistent with adsorbed polymer layers which are best fit using the mushroom model. Friction measurements show that the adsorbed polymer layer markedly reduces friction compared to surfaces sliding in the pure ILs and that lubricity increases with polymer length. When polymer is adsorbed to the sliding surfaces, friction is controlled by the creation and disruption of intermolecular interactions between entangled chains and the dragging of polymer chains through the interpenetration region. These experiments show that added polymer can reduce friction while maintaining the useful properties of ILs as lubricants. PMID:26844589

  5. Comparison of some new pretreatment methods for second generation bioethanol production from wheat straw and water hyacinth.

    PubMed

    Guragain, Yadhu Nath; De Coninck, Joelle; Husson, Florence; Durand, Alain; Rakshit, Sudip Kumar

    2011-03-01

    Pretreatment of lignocellulosic residues like water hyacinth (WH) and wheat straw (WS) using crude glycerol (CG) and ionic liquids (IL) pretreatment was evaluated and compared with conventional dilute acid pretreatment (DAT) in terms of enzymatic hydrolysis yield and fermentation yield of pretreated samples. In the case of WS, 1-butyl-3-methylimidazolium acetate pretreatment was found to be the best method. The hydrolysis yields of glucose and total reducing sugars were 2.1 and 3.3 times respectively higher by IL pretreatment than DAT, while it was 1.4 and 1.9 times respectively higher with CG pretreatment. For WH sample, CG pretreatment was as effective as DAT and more effective than IL pretreatment regarding hydrolysis yield. The fermentation inhibition was not noticeable with both types of pretreatment methods and feedstocks. Besides, CG pretreatment was found as effective as pure glycerol pretreatment for both feedstocks. This opens up an attractive economic route for the utilization of CG. PMID:21273061

  6. Ionic liquid as a promising biobased green solvent in combination with microwave irradiation for direct biodiesel production.

    PubMed

    Wahidin, Suzana; Idris, Ani; Shaleh, Sitti Raehanah Muhamad

    2016-04-01

    The wet biomass microalgae of Nannochloropsis sp. was converted to biodiesel using direct transesterification (DT) by microwave technique and ionic liquid (IL) as the green solvent. Three different ionic liquids; 1-butyl-3-metyhlimidazolium chloride ([BMIM][Cl], 1-ethyl-3-methylimmidazolium methyl sulphate [EMIM][MeSO4] and 1-butyl-3-methylimidazolium trifluoromethane sulfonate [BMIM][CF3SO3]) and organic solvents (hexane and methanol) were used as co-solvents under microwave irradiation and their performances in terms of percentage disruption, cell walls ruptured and biodiesel yields were compared at different reaction times (5, 10 and 15 min). [EMIM][MeSO4] showed highest percentage cell disruption (99.73%) and biodiesel yield (36.79% per dried biomass) after 15 min of simultaneous reaction. The results demonstrated that simultaneous extraction-transesterification using ILs and microwave irradiation is a potential alternative method for biodiesel production. PMID:26851899

  7. Volumetric properties of binary mixtures of benzene with cyano-based ionic liquids

    NASA Astrophysics Data System (ADS)

    Gonfa, Girma; Bustam, Mohamad Azmi; Moniruzzaman, Muhammad; Murugesan, Thanabalan

    2014-10-01

    The objective of this study is to investigate the volumetric properties of the binary mixtures comprised benzene and two ionic liquids, 1-butyl-3-methylimidazolium thiocyanate ([BMIM][SCN]) and 1-butyl-3-methyl- imidazolium dicyanamide ([ BMIM ][ N ( CN )2]( . Densities (ρ) and viscosities (μ) of the binary mixtures were measured over a temperature range of 293.15 to 323.15 K and at atmospheric pressure. Excess molar volumes and viscosity deviations were calculated from the experimental densities and viscosities values. The volumetric properties of the mixtures were changed significantly with the change of compositions and temperatures. It was also found that the value of excess molar volume and viscosity deviations were negative (-ve) over the entire range of compositions. The results have been interpreted in terms of molecular interactions of ILs and benzene.

  8. Efficient dehydration of 6-gingerol to 6-shogaol catalyzed by an acidic ionic liquid under ultrasound irradiation.

    PubMed

    Kou, Xingran; Li, Xingze; Rahman, Md Ramim Tanver; Yan, Minming; Huang, Huanhuan; Wang, Hongxin; Su, Yihai

    2017-01-15

    6-Gingerol and 6-shogaol are the main bioactive compounds in ginger. Although 6-shogaol has more and better bioactivities than its precursor 6-gingerol, the low content of 6-shogaol in ginger restricts its bioactive effects in functional foods. The traditional preparation methods of 6-shogaol are defective because of the environmental hazards and low efficiency of the processes. In this study, an efficient, easy and eco-friendly dehydration conversion of 6-gingerol to 6-shogaol is presented using an acidic ionic liquid 1-butyl-3-methylimidazolium hydrosulfate ([Bmim]HSO4) under ultrasound irradiation. The key parameters, including reaction temperature, reaction time, mass ratio of catalyst to substrate and ultrasonic power in each reaction process, were investigated. The yield of 6-shogaol reached as high as 97.16% under optimized condition. The catalyst could be separated from the reaction mixture and reused five times with only a slight loss of activity. PMID:27542467

  9. Use of Ionic Liquid in Fabrication, Characterization, and Processing of Anodic Porous Alumina

    PubMed Central

    2009-01-01

    Two different ionic liquids have been tested in the electrochemical fabrication of anodic porous alumina in an aqueous solution of oxalic acid. It was found that during galvanostatic anodization of the aluminum at a current density of 200 mA/cm2, addition of 0.5% relative volume concentration of 1-butyl-3-methylimidazolium tetrafluoborate resulted in a three-fold increase of the growth rate, as compared to the bare acidic solution with the same acid concentration. This ionic liquid was also used successfully for an assessment of the wettability of the outer surface of the alumina, by means of liquid contact angle measurements. The results have been discussed and interpreted with the aid of atomic force microscopy. The observed wetting property allowed to use the ionic liquid for protection of the pores during a test removal of the oxide barrier layer. PMID:20596395

  10. Spatially resolved electrochemistry in ionic liquids: surface structure effects on triiodide reduction at platinum electrodes.

    PubMed

    Aaronson, Barak D B; Lai, Stanley C S; Unwin, Patrick R

    2014-02-25

    Understanding the relationship between electrochemical activity and electrode structure is vital for improving the efficiency of dye-sensitized solar cells. Here, the reduction of triiodide to iodide in 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIm][BF4]) room temperature ionic liquid (RTIL) is investigated on polycrystalline platinum using scanning electrochemical cell microscopy (SECCM) and correlated to the crystallographic orientation from electron backscatter diffraction (EBSD). Although the rate determining step in all grains was the first electron transfer, significant grain-dependent variations in activity were revealed, with grains with a dominant (110) crystallographic character exhibiting higher catalytic activity compared to those with a major (100) orientation. The SECCM technique is demonstrated to resolve heterogeneity in activity, highlighting that methods incorporating polycrystalline electrodes miss vital details for understanding and optimizing electrocatalysts. An additional advantage of the SECCM over single-crystal techniques is its ability to probe high index facets. PMID:24479903

  11. Desulfurization of oxidized diesel using ionic liquids

    NASA Astrophysics Data System (ADS)

    Wilfred, Cecilia D.; Salleh, M. Zulhaziman M.; Mutalib, M. I. Abdul

    2014-10-01

    The extraction of oxidized sulfur compounds from diesel were carried out using ten types of ionic liquids consisting of different cation and anion i.e. 1-ethyl-3-methylimidazolium tetrafluoroborate, 1-butyl-3-methylimidazoium thiocyanate, 1-butyl-3-methylimidazoium dicyanamide, 1-butyl-3-methylimidazolium trifluoromethanesulfonate, 1-butyl-3-methylimidazoliumhexafluorophosphate, 1-hexyl-3-methylimidazolium trifluoromethanesulfonate, trioctylmethylammonium chloride, 1-propionitrile-3-butylimidazolium thiocyanate, 1-propionitrile-3-butylimidazolium dicyanamide and 1-butyl-6-methylquinolinium dicyanamide. The oxidation of diesel was successfully done using phosphotungstic acid as the catalyst, hydrogen peroxide (H2O2) as the oxidant and trioctylmethylammonium chloride as the phase transfer agent. The oxidation of diesel changes the sulfur compounds into sulfone which increases its polarity and enhances the ionic liquid's extraction performance. Result showed that ionic liquid [C4mquin][N(CN)2] performed the highest sulfur removal (91% at 1:5 diesel:IL ratio) compared to the others.

  12. Cellobiose as a model system to reveal cellulose dissolution mechanism in acetate-based ionic liquids: Density functional theory study substantiated by NMR spectra.

    PubMed

    Cao, Bobo; Du, Jiuyao; Du, Dongmei; Sun, Haitao; Zhu, Xiao; Fu, Hui

    2016-09-20

    Cellulose dissolution mechanism in acetate-based ionic liquids was systematically studied in Nuclear Magnetic Resonance (NMR) spectra and Density Functional Theory (DFT) methods by using cellobiose and 1-butyl-3-methylimidazolium acetate (BmimAc) as a model system. The solubility of cellulose in ionic liquid increased with temperature increase in the range of 90-140°C. NMR spectra suggested OAc(-) preferred to form stronger hydrogen bonds with hydrogen of hydroxyl in cellulose. Electrostatic potential method was employed to predict the most possible reaction sites and locate the most stable configuration. Atoms in molecules (AIM) theory was used to study the features of bonds at bond critical points and the variations of bond types. Simultaneously, noncovalent interactions were characterized and visualized by employing reduced density gradient analysis combined with Visual Molecular Dynamics (VMD) program. Natural bond orbital (NBO) theory was applied to study the noncovalent nature and characterize the orbital interactions between cellobiose and Bmim[OAc]. PMID:27261759

  13. Ionic liquid-aqueous solution ultrasonic-assisted extraction of three kinds of alkaloids from Phellodendron amurense Rupr and optimize conditions use response surface.

    PubMed

    Wang, Wenchao; Li, Qingyong; Liu, Yuhui; Chen, Binbin

    2015-05-01

    In this paper, we chose diffident kinds of ionic liquids to optimal selection an optimal one to extract alkaloids from Phellodendron amurense Rupr. Four ionic liquids with diffident carbon chains or anions have been investigated and 1-butyl-3-methylimidazolium bromide with best productivity. Then, selections have been optimized in different conditions, including concentration of ionic liquid, time for ultrasonic treatment, ultrasonic power and solid-liquid ratio. Moreover, three conditions have been comprehensively assessment by response surface methodology, the optimal conditions were determined as follows ultrasonic power 100 W, extraction time 75 min and ratio of solvent to raw material 1:14. Under these conditions, the yield% (MIX) was 106.7% (extracted by heat reflux being defined 100%). Comparing with other methods, the advantages are saving conserving, time saving, high yield% and especially pollution-free. PMID:25443277

  14. Microregion detection of ionic liquid microemulsions.

    PubMed

    Gao, Yanan; Wang, Suqing; Zheng, Liqiang; Han, Shuaibing; Zhang, Xuan; Lu, Deming; Yu, Li; Ji, Yongqiang; Zhang, Gaoyong

    2006-09-15

    Nonaqueous ionic liquid (IL) microemulsion consisting of IL, 1-butyl-3-methylimidazolium tetrafluoroborate (bmimBF(4)), surfactant TX-100, and toluene was prepared and the phase behavior of the ternary system was investigated. Electrical conductivity measurement was used for investigating the microregions of the nonaqueous IL microemulsions. On the basis of the percolation theory, the bmimBF(4)-in-toluene (IL/O), bicontinuous, and toluene-in-bmimBF(4) (O/IL) microregions of the microemulsions were successfully identified using insulative toluene as the titration phase. However, this method was invalid when conductive bmimBF(4) acted as the titration phase. The microregions obtained by conductivity measurements were further proved by electrochemical cyclic voltammetry experiments. The results indicated that the conductivity method was feasible for identifying microstructures of the nonaqueous IL microemulsions. PMID:16765365

  15. Dynamics of solvation and rotational relaxation of Coumarin 153 in ionic liquid confined nanometer-sized microemulsions.

    PubMed

    Chakrabarty, Debdeep; Seth, Debabrata; Chakraborty, Anjan; Sarkar, Nilmoni

    2005-03-31

    The effects of confinement of the ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate on solvation dynamics and rotational relaxation of Coumarin 153 (C-153) in Triton X-100/cyclohexane microemulsions have been explored using steady-state and picosecond time-resolved emission spectroscopy. The steady-state and rotational relaxation data indicate that C-153 molecules are incorporated in the core of the microemulsions. The average rotational relaxation time increases with increase in w ([bmim][BF(4)]/[TX-100]) values. The solvent relaxation in the core of the microemulsion occurs on two different time scales and is almost insensitive to the increase in w values. The solvent relaxation is retarded in the pool of the microemulsions compared to the neat solvent. Though, the retardation is very small compared to several-fold retardation of the solvation time of the conventional solvent inside the pool of the microemulsions. PMID:16851624

  16. Modified pineapple peel cellulose hydrogels embedded with sepia ink for effective removal of methylene blue.

    PubMed

    Dai, Hongjie; Huang, Huihua

    2016-09-01

    Novel composite hydrogels based on pineapple peel cellulose and sepia ink were synthesized by homogeneous acetylation of cellulose in ionic liquid 1-butyl-3-methylimidazolium chloride. The structure and morphology of the prepared hydrogels were characterized by Fourier transform infrared spectroscopy, field emission scanning electron microscope, X-ray diffraction, thermogravimetry and differential scanning calorimetry. The effects of acetylation time, acetylation temperature, molar ratio of acetic anhydride/anhydroglucose unit and the additive amount of sepia ink on methylene blue adsorption capacity of the hydrogels embedded with sepia ink were also investigated. Methylene blue adsorption of the hydrogels followed pseudo-second-order kinetic model and sepia ink improved adsorption capacity significantly. The adsorption capacity at equilibrium was increased from 53.72 to 138.25mg/g when the additive amount of sepia ink of the hydrogels was 10%. PMID:27185109

  17. Trivalent actinide and lanthanide separations using tetraalkyldiglycolamides (TCnDGA) in molecular and ionic liquid diluents

    SciTech Connect

    Bruce J. Mincher; Robert V. Fox; Mary E. Mincher; Chien M. Wai

    2014-09-01

    The use of the diglycolamide, tetrabutyldiglycolamide was investigated for intergroup separations of the lanthanides, focusing especially on those lanthanides (Y, Ce, Eu, Tb, Dy, Er, and Yb) found in lighting phosphors. Tetrabutyldiglycolamide extraction efficiency for the lanthanides varied depending on whether the diluent was the conventional molecular diluent 1-octanol, the ionic liquid 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)-imide, or a mixture of the two. This was attributed to extraction of either neutral, cationic or anionic lanthanide metal complexes with nitrate ion. Based on the batch contact solvent extraction results measured here, a series of extractions providing product streams containing separated Y, Ce, Eu, Tb/Dy, and Er/Yb are proposed.

  18. Supported Ionic Liquid Membranes and Ion-Jelly® Membranes with [BMIM][DCA]: Comparison of Its Performance for CO2 Separation

    PubMed Central

    Couto, Ricardo; Neves, Luísa; Simões, Pedro; Coelhoso, Isabel

    2015-01-01

    In this work, a supported ionic liquid membrane (SILM) was prepared by impregnating a PVDF membrane with 1-butyl-3-methylimidazolium dicyanamide ([BMIM][DCA]) ionic liquid. This membrane was tested for its permeability to pure gases (CO2, N2 and O2) and ideal selectivities were calculated. The SILM performance was also compared to that of Ion-Jelly® membranes, a new type of gelled membranes developed recently. It was found that the PVDF membrane presents permeabilities for pure gases similar or lower to those presented by the Ion-Jelly® membranes, but with increased ideal selectivities. This membrane presents also the highest ideal selectivity (73) for the separation of CO2 from N2 when compared with SILMs using the same PVDF support but with different ionic liquids. PMID:25594165

  19. Ionic liquids as novel solvents for biosynthesis of octenyl succinic anhydride-modified waxy maize starch.

    PubMed

    Li, Dandan; Zhang, Xiwen; Tian, Yaoqi

    2016-05-01

    Biosynthesis of octenyl succinic anhydride (OSA) starch was investigated using ionic liquids (ILs) as reaction media. Waxy maize starch was pretreated in 1-butyl-3-methylimidazolium chlorine and then esterified with OSA in 1-octyl-3-methylimidazolium nitrate by using Novozyme 435 as catalyst. The degree of substitution of OSA starch reached 0.0130 with 5 wt% starch concentration and 1 wt% lipase dosage based on ILs weight at 50 °C for 3h. The formation of OSA starch was confirmed by fourier transform infrared spectroscopy. Scanning electron microscopy and X-ray diffraction revealed that the morphology and crystal structure of starch were significantly destroyed. Thermogravimetric analysis showed that esterification decreased the thermal stability of starch. The successful lipase-catalyzed synthesis of OSA starch in ILs suggests that ILs are potential replacement of traditional organic solvents for starch ester biosynthesis. PMID:26797225

  20. Separation of Lignin from Corn Stover Hydrolysate with Quantitative Recovery of Ionic Liquid

    PubMed Central

    Underkofler, Kaylee A.; Teixeira, Rodrigo E.; Pietsch, Stephen A.; Knapp, Kurtis G.; Raines, Ronald T.

    2015-01-01

    Abundant lignocellulosic biomass could become a source of sugars and lignin, potential feedstocks for the now emergent bio-renewable economy. The production and conversion of sugars from biomass have been well-studied, but far less is known about the production of lignin that is amenable to valorization. Here we report the isolation of lignin generated from the hydrolysis of biomass dissolved in the ionic liquid 1-butyl-3-methylimidazolium chloride. We show that lignin can be isolated from the hydrolysate slurry by simple filtration or centrifugation, and that the ionic liquid can be recovered quantitatively by a straightforward wash with water. The isolated lignin is not only free from ionic liquid, but also lacks cellulosic residues and is substantially depolymerized, making it a promising feedstock for valorization by conversion into fuels and chemicals. PMID:25866701

  1. Study of molybdenum electrodes for hydrogen evolution reaction

    NASA Astrophysics Data System (ADS)

    Padilha, Janine Carvalho; Martini, Emilse Maria Agostini; Brum, Cauã; de Souza, Michèle Oberson; de Souza, Roberto Fernando

    The molybdenum electrode, Mo, has been investigated for hydrogen production via water electrolysis in 10 vol.% aqueous solutions of 1-butyl-3-methylimidazolium tetrafluoroborate (BMI·BF 4) using electrochemical impedance spectroscopy (EIS). The EIS measurements show that the Mo system has much higher interfacial capacitance, and correspondently the electrical double layer formed on this electrode is thicker than those formed on nickel or platinum. The positive displacement of potential of zero charge (PZC) values indicates the specific adsorption of the imidazolium cation on the Mo surface. This study provides an elegant explanation for the better performance of Mo electrodes in the hydrogen evolution reaction (HER): the BMI cation acts as an intermediate for the proton transfer from water to the electrode surface, thereby decreasing the overpotential of HER. This model explains the synergism between Mo and the BMI cation in the HER process.

  2. Application of Ionic Liquids in the Microwave-Assisted Extraction of Proanthocyanidins from Larix gmelini Bark

    PubMed Central

    Yang, Lei; Sun, Xiaowei; Yang, Fengjian; Zhao, Chunjian; Zhang, Lin; Zu, Yuangang

    2012-01-01

    Ionic liquid based, microwave-assisted extraction (ILMAE) was successfully applied to the extraction of proanthocyanidins from Larix gmelini bark. In this work, in order to evaluate the performance of ionic liquids in the microwave-assisted extraction process, a series of 1-alkyl-3-methylimidazolium ionic liquids with different cations and anions were evaluated for extraction yield, and 1-butyl-3-methylimidazolium bromide was selected as the optimal solvent. In addition, the ILMAE procedure for the proanthocyanidins was optimized and compared with other conventional extraction techniques. Under the optimized conditions, satisfactory extraction yield of the proanthocyanidins was obtained. Relative to other methods, the proposed approach provided higher extraction yield and lower energy consumption. The Larix gmelini bark samples before and after extraction were analyzed by Thermal gravimetric analysis, Fourier-transform infrared spectroscopy and characterized by scanning electron microscopy. The results showed that the ILMAE method is a simple and efficient technique for sample preparation. PMID:22606036

  3. Rapid Carbonation for Calcite from a Solid-Liquid-Gas System with an Imidazolium-Based Ionic Liquid

    PubMed Central

    Ibrahim, Abdul-Rauf; Vuningoma, Jean Bosco; Huang, Yan; Wang, Hongtao; Li, Jun

    2014-01-01

    Aqueous carbonation of Ca(OH)2 is a complex process that produces calcite with scalenohedral calcite phases and characterized by inadequate carbonate species for effective carbonation due to the poor dissolution of CO2 in water. Consequently, we report a solid-liquid-gas carbonation system with an ionic liquid (IL), 1-butyl-3-methylimidazolium bromide, in view of enhancing the reaction of CO2 with Ca(OH)2. The use of the IL increased the solubility of CO2 in the aqueous environment and enhanced the transport of the reactive species (Ca2+ and CO32−) and products. The presence of the IL also avoided the formation of the CaCO3 protective and passivation layer and ensured high carbonation yields, as well as the production of stoichiometric rhombohedral calcite phases in a short time. PMID:24968273

  4. Ionic liquid lubrication: influence of ion structure, surface potential and sliding velocity.

    PubMed

    Li, Hua; Rutland, Mark W; Atkin, Rob

    2013-09-21

    Colloid probe atomic force microscopy (AFM) has been employed to investigate the nanotribology of the ionic liquid (IL)-Au(111) interface. Data is presented for four ILs, 1-ethyl-3-methylimidazolium tris(pentafluoroethyl)trifluorophosphate ([EMIM] FAP), 1-butyl-3-methylimidazolium tris(pentafluoroethyl)trifluorophosphate ([BMIM] FAP), 1-hexyl-3-methylimidazolium tris(pentafluoroethyl)trifluorophosphate ([HMIM] FAP) and 1-butyl-3-methylimidazolium iodide ([BMIM] I), at different Au(111) surface potentials. Lateral forces vary as a function of applied surface potential and ion structure because the composition of the confined ion layer changes from cation-enriched (at negative potentials) to mixed (at 0 V), and to anion-enriched (at positive potentials). ILs with FAP(-) anions all exhibit similar nanotribology: low friction at negative potentials and higher friction at positive potentials. [BMIM] I displays the opposite behaviour, as an I(-) anion-enriched layer is more lubricating than either the [BMIM](+) or FAP(-) layers. The effect of cation charged group (charge-delocalised versus charged-localised) was investigated by comparing [BMIM] FAP with 1-butyl-1-methylpyrrolidinium tris(pentafluoroethyl)trifluorophosphate ([Py(1,4)] FAP). [BMIM] FAP is less lubricating at negative potentials, but more lubricating at positive potentials. This indicated that even at positive potentials the cation concentration in the boundary layer is sufficiently high to influence lubricity. The influence of sliding velocity on lateral force was investigated for the [EMIM] FAP-Au(111) system. At neutral potentials the behaviour is consistent with a discontinuous sliding process. When a positive or negative potential bias is applied, this effect is less pronounced as the colloid probe slides along a better defined ion plane. PMID:23836254

  5. Selective quenching of 2-naphtholate fluorescence by imidazolium ionic liquids.

    PubMed

    Kumar, Vinod; Pandey, Siddharth

    2012-10-01

    The effect of addition of water-miscible ionic liquids (ILs), 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF(4)]), 1-butyl-3-methylimidazolium trifluoromethanesulfonate ([bmim][OTf]), and 1-butyl-1-methylpyrrolidinium trifluoromethanesulfonate ([bmpyrr][OTf]), on photophysical properties of 2-naphthol in water at various pHs is reported. Electronic absorbance behavior of 2-naphthol dissolved in aqueous mixtures of ILs is observed to be similar to that found in water at different pHs. The excited-state properties, however, are changed dramatically as the IL is added to the milieu. The presence of imidazolium IL results in significant quenching of the fluorescence emission from 2-naphtholate. On the contrary, pyrrolidinium IL does not quench the fluorescence from the anionic species. The quenching of 2-naphtholate fluorescence by aromatic imidazolium cations in aqueous IL mixtures is found to follow simple Stern-Volmer behavior. The aromatic imidazolium cation acts as an electron/charge acceptor during the quenching process where formation of a weakly fluorescent complex between the imidazolium cation and the excited 2-naphtholate anion possibly involving the acidic C2 proton of imidazolium is proposed. Because of the absence of such an acidic proton, the nonaromatic pyrrolidinium cation is not able to form a complex with the excited 2-naphtholate and cannot act as an electron/charge acceptor. Excited-state emission intensity decay data further corroborate this hypothesis as the intensity decay fits well to a single-exponential decay with no change in recovered lifetimes as [bmpyrr][OTf] is added; a double-exponential decay is required to satisfactorily fit the decay data in the presence of [bmim][BF(4)], hinting at the presence of a weakly fluorescent complex. The uniqueness of ILs in affecting excited-state properties of the 2-naphthol system is demonstrated through comparison with NaBF(4), NaCl, and polyethylene glycol with an average molecular weight of

  6. Advanced two-photon photolithography for patterning of transparent, electrically conductive ionic liquid-polymer nanostructures

    NASA Astrophysics Data System (ADS)

    Bakhtina, Natalia A.; MacKinnon, Neil; Korvink, Jan G.

    2016-04-01

    A key challenge in micro- and nanotechnology is the direct patterning of functional structures. For example, it is highly desirable to possess the ability to create three-dimensional (3D), conductive, and optically transparent structures. Efforts in this direction have, to date, yielded less than optimal results since the polymer composites had low optical transparency over the visible range, were only slightly conductive, or incompatible with high resolution structuring. We have previously presented the novel cross-linkable, conductive, highly transparent composite material based on a photoresist (IP-L 780, OrmoComp, or SU-8) and the ionic liquid 1-butyl-3-methylimidazolium dicyanamide. Material patterning by conventional and two-photon photolithography has been demonstrated as proof-of-concept. Aiming to increase the resolution and to extend the spectrum of exciting applications we continued our research into identifying new ionic liquid - polymer composites. In this paper, we report the precise 3D single-step structuring of optically transparent and electrically conductive ionic liquid - polymer nanostructures with the highest spatial resolution (down to 150 nm) achieved to date. This was achieved via the development of novel cross-linkable composite based on the photoresist IP-G 780 and the ionic liquid 1-butyl-3-methylimidazolium dicyanamide. The successful combination of the developed material with the advanced direct laser writing technique enabled the time- and cost-saving direct manufacturing of transparent, electrically conductive components. We believe that the excellent characteristics of the structured material will open a wider range of exciting applications.

  7. Direct electrochemistry of cytochrome c entrapped in agarose hydrogel in room temperature ionic liquids.

    PubMed

    Wang, Sui; Guo, Zhiyong; Zhang, Huina

    2011-08-01

    Direct electrochemistry of cytochrome c (cyt-c) entrapped in agarose hydrogel on gold electrode (Au), edge plane pyrolytic graphite electrode (EPPGE) and glassy carbon electrode (GC) in two room temperature ionic liquids was investigated. The effects of the addition of N,N-dimethylformamide (DMF) in the agarose-cyt-c film, water concentration in ionic liquids and exterior metal ions on the electrochemical behavior of cyt-c were monitored, and electrocatalytic properties of cyt-c were also done. Results showed that a good quasi-reversible redox behavior of cyt-c could be found after adding DMF in agarose-cyt-c film, and peak shape would not change after continuously scanning for 50 cycles. In addition, a certain amount of water in hydrophilic ionic liquids is necessary to maintain electrochemical activities of cyt-c, electrochemical performance of cyt-c is the best when the water content is 5.2% and 5.8% for 1-butyl-3-methylimidazolium bromide ([Bmim][Br]) and 1-butyl-3-methylimidazolium tetrafluoroborate([Bmim][BF(4)]) respectively. However, electrochemical activities of cyt-c are inhibited by exterior metal ions. Interestingly, cyt-c entrapped in agarose hydrogel on EPPGE and GC could catalyze the electroreduction of trichloroacetic acid (TCA) and tert-butyl hydroperoxide (t-BuOOH) in [Bmim][BF(4)], but could not in [Bmim][Br]. Reasons for above-mentioned differences of electrochemical properties of cyt-c in different ionic liquids were preliminarily discussed. PMID:21659008

  8. Specific solvation interactions of CO2 on acetate and trifluoroacetate imidazolium based ionic liquids at high pressures.

    PubMed

    Carvalho, Pedro J; Alvarez, Víctor H; Schröder, Bernd; Gil, Ana M; Marrucho, Isabel M; Aznar, Martín; Santos, Luís M N B F; Coutinho, João A P

    2009-05-14

    New classes of acidic or basic ionic liquids (ILs) are gaining special attention, since the efficiency of many processes can be enhanced by the judicious manipulation of these properties. The absorption of sour gases can be enhanced by the basic character of the IL. The fluorination of the cation or the anion can also contribute to enhance the gas solubility. In this work these two characteristics are evaluated through the study of the gas-liquid equilibrium of two ionic liquids based on similar anions, 1-butyl-3-methylimidazolium acetate ([C4mim][Ac]) and 1-butyl-3-methylimidazolium trifluoroacetate ([C4mim][TFA]), with carbon dioxide (CO2) at temperatures up to 363 K and pressures up to 76 MPa. The data reported are shown to be thermodynamically consistent. Henry's constants estimated from the experimental data show the solubility of CO2 on the [C4mim][Ac] to be spontaneous unlike in [C4mim][TFA] due to the differences in solvation enthalpies in these systems. Ab initio calculations were performed on simple intermolecular complexes of CO2 with acetate and trifluoroacetate using MP2/6-31G(d) and the G3 and G3MP2 theoretical procedures to understand the interactions between CO2 and the anions. The theoretical study indicates that although both anions exhibit a simultaneous interaction of the two oxygen of the carboxylate group with the CO2, the acetate acts as a stronger Lewis base than the trifluoroacetate. 13C high-resolution and magic angle spinning (HRMAS) NMR spectra provide further evidence for the acid/base solvation mechanism and the stability of the acetate ion on these systems. Further similarities and differences observed between the two anions in what concerns the solvation of CO2 are discussed. PMID:19374423

  9. Evaluation of thermophysical properties of ionic liquids with polar solvent: a comparable study of two families of ionic liquids with various ions.

    PubMed

    Govinda, Varadhi; Attri, Pankaj; Venkatesu, Punnuru; Venkateswarlu, Ponneri

    2013-10-17

    In this work, we explore and compare the role of the ion effect on the thermophysical properties of two families of ionic liquids (ILs), namely, tetra-alkyl ammonium cation [R4N](+) with hydroxide [OH](-) anion and 1-alkyl-3-methyl imidazolium cation [amim](+) with different anions (chloride, methyl sulfate, and tetrafluoroborate), with polar solvent such as dimethylsulfoxide (DMSO) in the temperature range from 25 to 40 °C and over the whole concentration range of ILs. Two families of ILs, namely, tetramethyl ammonium hydroxide [(CH3)4N][OH] (TMAH), tetraethyl ammonium hydroxide [(C2H5)4N][OH] (TEAH), tetrapropyl ammonium hydroxide [(C3H7)4N][OH] (TPAH), and tetrabutyl ammonium hydroxide [(C4H9)4N][OH] (TBAH) from ammonium-based ILs and 1-ethyl-3-methylimidazolium chloride [Emim][Cl], 1-ethyl-3-methylimidazolium methylsulfate [Emim][MeSO4], 1-butyl-3-methylimidazolium tetrafluoroborate [Bmim][BF4], and 1-butyl-3-methylimidazolium chloride ([Bmim][Cl]) from imidazolium family of ILs, are used in the present study. To address the molecular interactions of ILs with DMSO, densities (ρ), ultrasonic sound velocities (u), and viscosities (η) have been measured over the entire composition range and at four temperatures, 25, 30, 35, and 40 °C, under atmospheric pressure. From these experimental data, the excess molar volume (V(E)), the deviation in isentropic compressibility (Δκs), and the deviation in viscosity (Δη) were calculated and were adequately correlated by using the Redlich-Kister polynomial equation. The measured and predicted data were interpreted on the basis of intermolecular interactions and structural effects between like and unlike molecules upon mixing. The hydrogen-bonding features between ammonium-based ILs and DMSO were analyzed using molecular modeling program by HyperChem 7. PMID:24087984

  10. Synthesis of Cu, Zn and Cu/Zn brass alloy nanoparticles from metal amidinate precursors in ionic liquids or propylene carbonate with relevance to methanol synthesis

    NASA Astrophysics Data System (ADS)

    Schütte, Kai; Meyer, Hajo; Gemel, Christian; Barthel, Juri; Fischer, Roland A.; Janiak, Christoph

    2014-02-01

    Microwave-induced decomposition of the transition metal amidinates {[Me(C(NiPr)2)]Cu}2 (1) and [Me(C(NiPr)2)]2Zn (2) in the ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIm][BF4]) or in propylene carbonate (PC) gives copper and zinc nanoparticles which are stable in the absence of capping ligands (surfactants) for more than six weeks. Co-decomposition of 1 and 2 yields the intermetallic nano-brass phases β-CuZn and γ-Cu3Zn depending on the chosen molar ratios of the precursors. Nanoparticles were characterized by high-angle annular dark field-scanning transmission electron microscopy (HAADF-STEM), dynamic light scattering and powder X-ray diffractometry. Microstructure characterizations were complemented by STEM with spatially resolved energy-dispersive X-ray spectrometry and X-ray photoelectron spectroscopy. Synthesis in ILs yields significantly smaller nanoparticles than in PC. β-CuZn alloy nanoparticles are precursors to catalysts for methanol synthesis from the synthesis gas H2/CO/CO2 with a productivity of 10.7 mol(MeOH) (kg(Cu) h)-1.Microwave-induced decomposition of the transition metal amidinates {[Me(C(NiPr)2)]Cu}2 (1) and [Me(C(NiPr)2)]2Zn (2) in the ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIm][BF4]) or in propylene carbonate (PC) gives copper and zinc nanoparticles which are stable in the absence of capping ligands (surfactants) for more than six weeks. Co-decomposition of 1 and 2 yields the intermetallic nano-brass phases β-CuZn and γ-Cu3Zn depending on the chosen molar ratios of the precursors. Nanoparticles were characterized by high-angle annular dark field-scanning transmission electron microscopy (HAADF-STEM), dynamic light scattering and powder X-ray diffractometry. Microstructure characterizations were complemented by STEM with spatially resolved energy-dispersive X-ray spectrometry and X-ray photoelectron spectroscopy. Synthesis in ILs yields significantly smaller nanoparticles than in PC.

  11. Hydrothermal microwave valorization of eucalyptus using acidic ionic liquid as catalyst toward a green biorefinery scenario.

    PubMed

    Xu, Ji-Kun; Chen, Jing-Huan; Sun, Run-Cang

    2015-10-01

    The application of the acidic ionic liquid (IL), 1-butyl-3-methylimidazolium hydrogensulfate ([bmim]HSO4), as a catalyst in the hydrothermal microwave treatment (HMT) and green upgradation of eucalyptus biomass has been investigated. The process was carried out in a microwave reactor system at different temperatures (140-200°C) and evaluated for severities. The xylooligosaccharides (XOS, refers to a DP of 2-6) yield up to 5.04% (w/w) of the initial biomass and 26.72% (w/w) of xylan were achieved. Higher temperature resulted in lower molecular weight product, and enhanced the concentration of monosaccharides and byproducts. The morphology and structure of the solid residues were performed using an array of techniques, such as SEM, XRD, FTIR, BET surface area, and CP/MAS (13)C NMR, by which the increase of crystallinity, the destruction of surface structure, and the changes in functional groups and compositions were studied after the pretreatment, thus significantly enhancing the enzymatic hydrolysis. PMID:26119053

  12. Understanding positive and negative deviations in polarity of ionic liquid mixtures by pseudo-solvent approach.

    PubMed

    Beniwal, Vijay; Kumar, Anil

    2016-08-24

    Physico-chemical properties of liquid mixtures in general display large deviations from linear behaviour, arising out of complex specific and non-specific intermolecular interactions. The polarity of liquid mixtures displaying large positive and negative deviations can be minimized and linear mixing can be achieved in liquids using a pseudo-solvent methodology. The work described herein is designed to investigate the influence of different physical parameters on the linear pseudo-solvent composition in ionic liquid mixtures. For this purpose, we have determined the deviations from linearity, ΔE values (defined as given by ) for binary mixtures of a variety of ionic liquids, including two molecular solvents, DMSO and formamide. Firstly, the investigations were carried out in three 1-butyl-3-methylimidazolium cation based aprotic ionic liquids and the roles of anionic structure and hydrogen bond acceptor basicities (β values) of the ionic liquids were determined. The influence of the cationic structure, i.e., the hydrogen bond donor acidity (α values) and non-associative nature of the ionic liquids, was determined using C2-methylated analogs, 1-butyl-2,3-dimethylimidazolium cation based ionic liquids. The role of the protic nature of ionic liquids was studied in two protic ionic liquids, viz., 1-methylimidazolium formate and 1-methylimidazolium acetate. The effects of the temperature, pseudo-solvent structure and solvatochromic probe structure on the ΔE values were also explored. PMID:27523572

  13. Comparing an ionic liquid to a molecular solvent in the cesium cation extraction by a calixarene: a molecular dynamics study of the aqueous interfaces.

    PubMed

    Sieffert, Nicolas; Wipff, Georges

    2006-10-01

    We report a molecular dynamics (MD) study of the interfacial behavior of key partners involved in the Cs(+) cation extraction by a calix[4]arene-crown-6 host (L), comparing an ionic liquid (IL) to a classical molecular solvent (chloroform) as receiving "oil" phase. The IL is composed of hydrophobic 1-butyl-3-methylimidazolium cations (BMI(+)) and bis(trifluoromethylsulfonyl)imide anions (Tf(2)N(-)) and forms a biphasic system with water. The simulations reveal similarities but also interesting differences between the two types of interfaces. Much longer times are needed to "equilibrate" IL systems, compared to classical liquid mixtures, and there is more intersolvent mixing with the IL than with chloroform, especially concerning the water-in-oil content. There is also some excess of the BMI(+) cations over the Tf(2)N(-) anions in the aqueous phase. Simulations on the Na(+)NO(3)(-) and Cs(+)NO(3)(-) ions show that they sometimes interact at the interface with the IL ions, forming hydrated intimate ion pairs, whereas they are "repelled" by the classical interface. The LCs(+) complex and L ligand also behave differently, depending on the "oil phase". They are better solvated by the IL than by chloroform and thus poorly attracted at the IL interface, whereas they adsorb at the chloroform interface, adopting well-defined amphiphilic orientations. The results are discussed in the context of assisted ion transfer and provide a number of arguments explaining the specificity and efficiency of IL based, compared to classical extraction systems. PMID:17004811

  14. Ionic liquid-based aqueous two-phase system extraction of sulfonamides in milk.

    PubMed

    Shao, Mingyuan; Zhang, Xuli; Li, Na; Shi, Jiayuan; Zhang, Huijie; Wang, Zhibing; Zhang, Hanqi; Yu, Aimin; Yu, Yong

    2014-06-15

    A simple method for the determination of six sulfonamides (SAs) in milk samples was developed. 1-Butyl-3-methylimidazolium tetrafluoroborate and trisodium citrate dihydrate were used to form aqueous two-phase system. The aqueous two phase system was applied to the extraction of the SAs and the determination of the analytes was performed by high-performance liquid chromatography. To achieve optimum extraction performance, several experimental parameters, including the type and the amount of salt, the type and amount of ionic liquid, ultrasonic time and pH of sample solution, were investigated and optimized. Under the optimal experimental conditions, good linearity was observed in the range of 8.55-1036.36ngmL(-1). The limits of detection and quantification were in the range of 2.04-2.84 and 6.73-9.37ngmL(-1), respectively. The present method was successfully applied to the determination of SAs in milk samples, and the recoveries of analytes were in the range of 72.32-108.96% with relative standard deviations ranging from 0.56 to 12.20%. The results showed that the present method was rapid, feasible and environmentally friendly. PMID:24854709

  15. Role of the Hofmeister series in the formation of ionic-liquid-based aqueous biphasic systems.

    PubMed

    Shahriari, Shahla; Neves, Catarina M S S; Freire, Mara G; Coutinho, João A P

    2012-06-21

    Among the numerous and interesting features of ionic liquids is their ability to form aqueous biphasic systems (ABSs) when combined with inorganic or organic salts in aqueous media. In this work, a wide range of salts was studied, aiming at gathering a detailed picture on the molecular mechanisms that govern the ability of the salt ions to induce the formation of ionic-liquid-based ABSs. For that purpose, 1-butyl-3-methylimidazolium trifluoromethanesulfonate was chosen due to its facility to undergo liquid-liquid demixing in aqueous media containing conventional salts. The corresponding ternary phase diagrams, tie-lines, and tie-line lengths were determined at 298 K and atmospheric pressure. With the large body of data measured in this work, it was possible to establish a scale on the salt cation and anion abilities to induce the formation of ionic-liquid-based ABSs, which follows the Hofmeister series, and to show that the molar entropy of hydration of the salt ions is the driving force for aqueous two-phase system formation. PMID:22594382

  16. Ionic liquid and aqueous two-phase extraction based on salting-out coupled with high-performance liquid chromatography for the determination of seven rare ginsenosides in Xue-Sai-Tong injection.

    PubMed

    Li, Lan-Jie; Jin, Yong-Ri; Wang, Xiao-Zhong; Liu, Ying; Wu, Qian; Shi, Xiao-Lei; Li, Xu-Wen

    2015-09-01

    A method of ionic liquid salt aqueous two-phase extraction coupled with high-performance liquid chromatography has been developed for the analysis of seven rare ginsenosides including Rg6 , F4 , 20(S)-Rg3 , 20(R)-Rg3 , Rk3 , Rk1 , and Rg5 in Xue-Sai-Tong injection. The injection was mixed with ionic liquid 1-butyl-3-methylimidazolium bromide aqueous solution, and a mixture was obtained. With the addition of sodium dodecyl sulfate and dipotassium phosphate into the mixture, the aqueous two-phase mixture was formed after ultrasonic treatment and centrifuged. Rare ginsenosides were extracted into the upper phase. To obtain a high extraction factors, various influences were considered systematically, such as the volume of ionic liquid, the category and amount of salts, the amount of sodium dodecyl sulfate, the pH value of system, and the time of ultrasonic treatment. Under the optimal condition, rare ginsenosides in Xue-Sai-Tong injection were enriched and detected, the recoveries of seven rare ginsenosides ranged from 90.05 to 112.55%, while relative standard deviations were lower than 2.50%. The developed method was reliable, rapid and sensitive for the determination of seven rare ginsenosides in the injections. PMID:26081987

  17. ILs-based microwave-assisted extraction coupled with aqueous two-phase for the extraction of useful compounds from Chinese medicine.

    PubMed

    Lin, Xiao; Wang, Yuzhi; Liu, Xiaojie; Huang, Songyun; Zeng, Qun

    2012-09-01

    Ionic liquids-based microwave-assisted extraction (ILs-MAE) of medicinal or useful compounds from plants was investigated as an alternative to conventional organic solvent extractions. The extraction and the preconcentration of aqueous two-phase (ATP) systems have been integrated. Various operating parameters were systematically considered by single-factor and L(9) (3(4)) orthogonal array experiments. 1-Butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF(4)]) has been selected to extract Apocynum venetum. The extract was then converted to the top phase by [bmim][BF(4)]/NaH(2)PO(4) system which was suitable for the preconcentration. Reversed phase high performance liquid chromatography (RP-HPLC) with ultraviolet detection was employed for the analysis of hyperin and isoquercitrin in Apocynum venetum. The optimal experiment approach could provide higher detection limit of hyperin and isoquercitrin which were 3.82 μg L(-1) and 3.00 μg L(-1) in Apocynum venetum. The recoveries of hyperin and isoquercitrin were 97.29% (RSD = 1.02%) and 99.40% (RSD = 1.13%), respectively, from aqueous samples of Apocynum venetum by the proposed method. Moreover, the extraction mechanism of ILs-MAE and the microstructures and chemical structures of the herb before and after extraction were also investigated. The method exhibited potential applicability with other complicated samples. PMID:22785248

  18. Extraction of proteins from biological fluids by use of an ionic liquid/aqueous two-phase system.

    PubMed

    Du, Zhuo; Yu, Yong-Liang; Wang, Jian-Hua

    2007-01-01

    An ionic liquid/aqueous two-phase system based on the hydrophilic ionic liquid 1-butyl-3-methylimidazolium chloride (BmimCl) and K(2)HPO(4) has been employed for direct extraction of proteins from human body fluids for the first time. Proteins present at low levels were quantitatively extracted into the BmimCl-rich upper phase with a distribution ratio of about 10 between the upper and lower phase and an enrichment factor of 5. Addition of an appropriate amount of K(2)HPO(4) to the separated upper phase results in a further phase separation, giving rise to an improved enrichment factor of 20. FTIR and UV spectroscopy demonstrated that no chemical (bonding) interactions between the ionic liquid and the protein functional groups were identifiable, while no alterations of the natural properties of the proteins were observed. The partitioning of proteins in the two-phase system was assumed to have been facilitated by the electrostatic potential difference between the coexisting phases, as well as by salting out effects. The system could be applied successfully for the quantification of proteins in human urine after on-line phase separation in a flow system. The use of an ionic liquid, as a green solvent, offers clear advantages over traditional liquid-liquid extractions, in which the use of toxic organic solvents is unavoidable. PMID:17136782

  19. Extraction of testosterone and epitestosterone in human urine using aqueous two-phase systems of ionic liquid and salt.

    PubMed

    He, Chiyang; Li, Shehong; Liu, Huwei; Li, Kean; Liu, Feng

    2005-08-01

    Based on aqueous two-phase systems (ATPS) consisting of 1-butyl-3-methylimidazolium chloride, a hydrophilic ionic liquid (IL), and K2HPO4, a new and simple extraction technique, coupled with a reversed-phase high performance liquid chromatography (RP-HPLC), was developed for the simultaneous concentration and analysis of testosterone (T) and epitestosterone (ET) in human urine. Under the optimal conditions, the extraction efficiencies for both analytes were 80-90% in a one-step extraction. The method required only 3.0 mL of urine and a single hydrolysis/deproteinization/extraction step followed by direct injection of the IL-rich upper phase into HPLC system for analysis. The method has been satisfactorily applied to the analysis of T and ET in human urine with detection limits of 1 ng/mL and linear ranges of 10-500 ng/mL for both compounds. Compared with conventional liquid-liquid extraction or solid phase extraction, this new method is much "greener" due to no use of volatile organic solvent and low consumption of IL. The proposed extraction technique opens up new possibilities in the separation of other drugs. PMID:16035355

  20. Development of regenerated cellulose/halloysite nanotube bionanocomposite films with ionic liquid.

    PubMed

    Soheilmoghaddam, Mohammad; Wahit, Mat Uzir

    2013-07-01

    In this study, novel nanocomposite films based on regenerated cellulose/halloysite nanotube (RC/HNT) have been prepared using an environmentally friendly ionic liquid 1-butyl-3-methylimidazolium chloride (BMIMCl) through a simple green method. The structural, morphological, thermal and mechanical properties of the RC/HNT nanocomposites were investigated using X-ray diffraction (XRD), Fourier transform infrared (FTIR), field emission scanning electron microscopy (FESEM), thermal analysis and tensile strength measurements. The results obtained revealed interactions between the halloysite nanotubes and regenerated cellulose matrix. The thermal stability and mechanical properties of the nanocomposite films, compared with pure regenerated cellulose film, were significantly improved When the halloysite nanotube (HNT) loading was only 2 wt.%, the 20% weight loss temperature (T20) increased 20°C. The Young's modulus increased from 1.8 to 4.1 GPa, while tensile strength increased from 35.30 to 60.50 MPa when 8 wt.% halloysite nanotube (HNT) was incorporated, interestingly without loss of ductility. The nanocomposite films exhibited improved oxygen barrier properties and water absorption resistance compared to regenerated cellulose. PMID:23567285

  1. Ionic liquid-assisted solvothermal synthesis of hollow Mn2O3 anode and LiMn2O4 cathode materials for Li-ion batteries

    NASA Astrophysics Data System (ADS)

    He, Xin; Wang, Jun; Jia, Haiping; Kloepsch, Richard; Liu, Haidong; Beltrop, Kolja; Li, Jie

    2015-10-01

    Mn-based Mn2O3 anode and LiMn2O4 cathode materials are prepared by a solvothermal method combined with post annealing process. Environmentally friendly ionic liquid 1-Butyl-3-methylimidazolium tetrafluoroborate as both structure-directing agent and fluorine source is used to prepare hollow polyhedron MnF2 precursor. Both target materials Mn2O3 anode and LiMn2O4 cathode have the morphology of the MnF2 precursor. The Mn2O3 anode using carboxymethyl cellulose as binder could deliver slight better electrochemical performance than the one using poly (vinyldifluoride) as binder. The former has an initial charge capacity of 800 mAh g-1 at a current density of 101.8 mA g-1, and exhibits no obvious capacity decay for 150 cycles at 101.8 mA g-1. The LiMn2O4 cathode material prepared with molten salt assistant could display much better electrochemical performance than the one prepared without molten salt assistance. In particular, it has an initial discharge capacity of 117.5 mAh g-1 at a current density of 0.5C and good rate capability. In the field of lithium ion batteries, both the Mn2O3 anode and LiMn2O4 cathode materials could exhibit enhanced electrochemical performance due to the well formed morphology based on the ionic liquid-assisted solvothermal method.

  2. Molybdenum-Bismuth Bimetallic Chalcogenide Nanosheets for Highly Efficient Electrocatalytic Reduction of Carbon Dioxide to Methanol.

    PubMed

    Sun, Xiaofu; Zhu, Qinggong; Kang, Xinchen; Liu, Huizhen; Qian, Qingli; Zhang, Zhaofu; Han, Buxing

    2016-06-01

    Methanol is a very useful platform molecule and liquid fuel. Electrocatalytic reduction of CO2 to methanol is a promising route, which currently suffers from low efficiency and poor selectivity. Herein we report the first work to use a Mo-Bi bimetallic chalcogenide (BMC) as an electrocatalyst for CO2 reduction. By using the Mo-Bi BMC on carbon paper as the electrode and 1-butyl-3-methylimidazolium tetrafluoroborate in MeCN as the electrolyte, the Faradaic efficiency of methanol could reach 71.2 % with a current density of 12.1 mA cm(-2) , which is much higher than the best result reported to date. The superior performance of the electrode resulted from the excellent synergistic effect of Mo and Bi for producing methanol. The reaction mechanism was proposed and the reason for the synergistic effect of Mo and Bi was discussed on the basis of some control experiments. This work opens a way to produce methanol efficiently by electrochemical reduction of CO2 . PMID:27098284

  3. Extraction and characterization of lignin from oil palm biomass via ionic liquid dissolution and non-toxic aluminium potassium sulfate dodecahydrate precipitation processes.

    PubMed

    Mohtar, S S; Tengku Malim Busu, T N Z; Md Noor, A M; Shaari, N; Yusoff, N A; Bustam Khalil, M A; Abdul Mutalib, M I; Mat, H B

    2015-09-01

    The objective of this study is to extract and characterize lignin from oil palm biomass (OPB) by dissolution in 1-butyl-3-methylimidazolium chloride ([bmim][Cl]), followed by the lignin extraction through the CO2 gas purging prior to addition of aluminum potassium sulfate dodecahydrate (AlK(SO4)2 · 12H2O). The lignin yield, Y(L) (%wt.) was found to be dependent of the types of OPB observed for all precipitation methods used. The lignin recovery, RL (%wt.) obtained from CO2-AlK(SO4)2 · 12H2O precipitation was, however dependent on the types of OPB, which contradicted to that of the acidified H2SO4 and HCl solutions of pH 0.7 and 2 precipitations. Only about 54% of lignin was recovered from the OPB. The FTIR results indicate that the monodispersed lignin was successfully extracted from the OPT, OPF and OPEFB having a molecular weight (MW) of 1331, 1263 and 1473 g/mol, and degradation temperature of 215, 207.5 and 272 °C, respectively. PMID:26038325

  4. Choline chloride-thiourea, a deep eutectic solvent for the production of chitin nanofibers.

    PubMed

    Mukesh, Chandrakant; Mondal, Dibyendu; Sharma, Mukesh; Prasad, Kamalesh

    2014-03-15

    Deep eutectic solvents (DESs) consisting of the mixtures of choline halide (chloride/bromide)-urea and choline chloride-thiourea were used as solvents to prepare α-chitin nanofibers (CNFs). CNFs of diameter 20-30 nm could be obtained using the DESs comprising of the mixture of choline chloride and thiourea (CCT 1:2); however, NFs could not be obtained using the DESs having urea (CCU 1:2) as hydrogen bond donor. The physicochemical properties of thus obtained NFs were compared with those obtained using a couple of imidazolium based ionic liquids namely, 1-butyl-3-methylimidazolium hydrogen sulphate [(Bmim)HSO4] and 1-methylimidazolium hydrogen sulphate [(Hmim)HSO4] as well as choline based bio-ILs namely, choline hydrogen sulphate [(Chol)HSO4] and choline acrylate. The CNFs obtained using the DES as a solvent were used to prepare calcium alginate bio-nanocomposite gel beads having enhanced elasticity in comparison to Ca-alginate beads. The bio-nanocomposite gel beads thus obtained were used to study slow release of 5-fluorouracil, an anticancer drug. PMID:24528755

  5. Highly Luminescent Salts Containing Well-Shielded Lanthanide-Centered Complex Anions and Bulky Imidazolium Countercations

    SciTech Connect

    Tang, Si-Fu; Lorbeer, Chantal; Wang, Xinjiao; Ghosh, Pushpal; Mudring, Anja-Verena

    2014-09-02

    Four salts containing imidazolium cations and europium(III)- or terbium(III)-centered complex anions have been successfully synthesized from an ethanol/H2O solution. The single-crystal X-ray diffraction analyses reveal that these compounds have a common formula of [R][Ln(DETCAP)4] [R = 1-ethyl-3-methylimidazolium (C2mim), Ln = Eu (1) and Tb (2); R = 1-butyl-3-methylimidazolium (C4mim), Ln = Eu (3) and Tb (4); DETCAP = diethyl-2,2,2-trichloroacetylphosphoramidate], in which the lanthanide centers are chelated by four chelating pseudo-β-diketonate ligands (DETCAP)-, forming the respective complex anions. Their thermal behaviors and stabilities were also investigated to study the role of the length of the side chain in the cations. Fluorescence measurements at both room temperature and liquid-nitrogen temperature show that these materials show intense characteristic europium(III) or terbium(III) emissions and have long decay times. Their overall quantum yields were determined to be in the range of 30–49%.

  6. DFT Study of the Reaction Mechanisms of Carbon Dioxide and its Isoelectronic Molecules CS2 and OCS Dissolved in Pyrrolidinium and Imidazolium Acetate Ionic Liquids.

    PubMed

    Danten, Y; Cabaço, M I; Coutinho, J A P; Pinaud, Noël; Besnard, M

    2016-06-16

    The reaction mechanisms of CO2 and its isoelectronic molecules OCS and CS2 dissolved in N-butyl-N-methylpyrrolidinium acetate and in 1-butyl-3-methylimidazolium acetate were investigated by DFT calculations in "gas phase". The analysis of predicted multistep pathways allowed calculating energies of reaction and energy barriers of the processes. The major role played by the acetate anion in the degradation of the solutes CS2 and OCS as well as in the capture of OCS and CO2 by the imidazolium ring is highlighted. In both ionic liquids, this anion governs the conversion of CS2 into OCS and of OCS into CO2 through interatomic S-O exchanges between the anion and the solutes with formation of thioacetate anions. In imidazolium acetate, the selective capture of CS2 and OCS by the imidazolium ring competes with the S-O exchanges. From the calculated values of the energy barriers a basicity scale of the anions is proposed. The (13)C NMR chemical shifts of the predicted adducts were calculated and agree well with the experimental observations. It is argued that the scenario issued from the calculated pathways is shown qualitatively to be independent from the functionals and basis set used, constitute a valuable tool in the understanding of chemical reactions taking place in liquid phase. PMID:27186961

  7. Stable iron carbide nanoparticle dispersions in [Emim][SCN] and [Emim][N(CN)2] ionic liquids.

    PubMed

    Khare, Varsha; Kraupner, Alexander; Mantion, Alexandre; Jelicić, Aleksandra; Thünemann, Andreas F; Giordano, Cristina; Taubert, Andreas

    2010-07-01

    Dispersions of Fe(3)C nanoparticles in several ionic liquids (ILs) have been investigated. The ILs are based on 1-ethyl-3-methylimidazolium [Emim] and 1-butyl-3-methylimidazolium [Bmim] cations. Anions are ethylsulfate [ES], methanesulfonate [MS], trifluoromethylsulfonate (triflate) [TfO], tetrafluoroborate [BF(4)], dicyanamide [N(CN)(2)], and thiocyanate [SCN]. Among the ILs studied, [Emim][SCN] and [Emim][N(CN)(2)] stand out because only in these ILs have stable and transparent nanoparticle dispersions been obtained. All other ILs lead to blackish, slightly turbid dispersions or to completely nontransparent suspensions, which often contain undispersed sediment. UV/vis spectroscopy, transmission electron microscopy, and X-ray scattering suggest that the reason for the stabilization of the Fe(3)C nanoparticles in [Emim][SCN] is the leaching of traces of iron from the particles (without affecting the crystal structure of the Fe(3)C particles). The resulting particle surface is thus carbon-rich, which presumably favors the stabilization of the particles. A similar explanation can be postulated for [Emim][N(CN)(2)], with the dicyanamide anion also being a good ligand for iron. PMID:20426431

  8. A study of the acid-catalyzed hydrolysis of cellulose dissolved in ionic liquids and the factors influencing the dehydration of glucose and the formation of humins.

    PubMed

    Dee, Sean J; Bell, Alexis T

    2011-08-22

    An investigation was carried out into the hydrolysis of cellulose dissolved in 1-ethyl-3-methylimidazolium chloride ([Emim][Cl]) and 1-butyl-3-methylimidazolium chloride ([Bmim][Cl]) catalyzed by mineral acids. Glucose, cellobiose, and 5-hydroxymethylfurfural (5-HMF) were observed as the primary reaction products. The initial rate of glucose formation was determined to be of first order in the concentrations of dissolved glucan and protons and of zero order in the concentration of water. The absence of a dependence on water concentration suggests that cleavage of the β-1,4-glycosidic linkages near chain ends is irreversible. The apparent activation energy for glucose formation is 96 kJ mol(-1). The absence of oligosaccharides longer than cellobiose suggests that cleavage of interior glycosidic bonds is reversible due to the slow diffusional separation of cleaved chains in the highly viscous glucan/ionic liquid solution. Progressive addition of water during the course of glucan hydrolysis inhibited the rate of glucose dehydration to 5-HMF and the formation of humins. The inhibition of glucose dehydration is attributed to stronger interaction of protons with water than the 2-OH atom of the pyranose ring of glucose, the critical step in the proposed mechanism for the formation of 5-HMF. The reduction in humin formation associated with water addition is ascribed to the lowered concentration of 5-HMF, since the formation of humins is suggested to proceed through the condensation polymerization of 5-HMF with glucose. PMID:21809450

  9. Ionic liquid activated Bacillus subtilis lipase A variants through cooperative surface substitutions.

    PubMed

    Zhao, Jing; Jia, Ning; Jaeger, Karl-Erich; Bocola, Marco; Schwaneberg, Ulrich

    2015-10-01

    The interest in performing enzyme-catalyzed reactions in amphiphilic systems, e.g., imidazolium-based ionic liquids (ILs) or surfactants, has been increased over the past decades. Directed protein evolution has been successful in tailoring enzymes for desired properties. Herein, nine IL-resistant Bacillus subtilis lipase A variants, particularly an IL-activated variant M1 (M134N/N138S/L140S), were identified by directed evolution. For instance, variant M2 (M134R/L140S) showed almost doubled specific activity (16.9 vs. 9.4 U/mg) and resistance (233% vs. 111%) at 9 vol% 1-butyl-3-methylimidazolium trifluoromethanesulfonate ([C4 mim][TfO]) compared with wild-type. The specific activities and resistance of purified individual single and double variants have been studied in five different IL-aqueous mixtures. The re-activation of lipase variant M1 (not wild-type) at high IL concentration was attributed to the cooperative effect of three surface substitutions (M134N, N138S, L140S) near the substrate-binding cleft. The presence of IL/substrate clusters under assay conditions was likely related to the re-activation effect. This study provides first example of IL-activated lipase variant generated by protein engineering, and helps to better understand the protein-IL interaction. PMID:25899108

  10. Phase Transitions of Triflate-Based Ionic Liquids under High Pressure.

    PubMed

    Faria, Luiz F O; Ribeiro, Mauro C C

    2015-11-01

    Raman spectroscopy has been used to study phase transitions of ionic liquids based on the triflate anion, [TfO](-), as a function of pressure or temperature. Raman spectra of ionic liquids containing the cations 1-butyl-3-methylimidazolium, [C4C1Im](+), 1-octyl-3-methylimidazolium, [C8C1Im](+), 1-butyl-2,3-dimethylimidazolium, [C4C1C1Im](+), and 1-butyl-1-methylpyrrolidinium, [C4C1Pyr](+), were compared. Vibrational frequencies and binding energy of ionic pairs were calculated by quantum chemistry methods. The ionic liquids [C4C1Im][TfO] and [C4C1Pyr][TfO] crystallize at 1.0 GPa when the pressure is increased in steps of ∼ 0.2 GPa from the atmospheric pressure, whereas [C8C1Im][TfO] and [C4C1C1Im][TfO] do not crystallize up to 2.3 GPa of applied pressure. The low-frequency range of the Raman spectrum of [C4C1Im][TfO] indicates that the system undergoes glass transition, rather than crystallization, when the pressure applied on the liquid has been increased above 2.0 GPa in a single step. Strong hysteresis of spectral features (frequency shift and bandwidth) of the high-pressure crystalline phase when the pressure was released stepwise back to the atmospheric pressure has been found . PMID:26457868

  11. Unique role of ionic liquid [bmin][BF 4] during curcumin-surfactant association and micellization of cationic, anionic and non-ionic surfactant solutions

    NASA Astrophysics Data System (ADS)

    Patra, Digambara; Barakat, Christelle

    2011-09-01

    Hydrophilic ionic liquid, 1-butyl-3-methylimidazolium tetrafluoroburate, modified the properties of aqueous surfactant solutions associated with curcumin. Because of potential pharmaceutical applications as an antioxidant, anti-inflammatory and anti-carcinogenic agent, curcumin has received ample attention as potential drug. The interaction of curcumin with various charged aqueous surfactant solutions showed it exists in deprotonated enol form in surfactant solutions. The nitro and hydroxyl groups of o-nitrophenol interact with the carbonyl and hydroxyl groups of the enol form of curcumin by forming ground state complex through hydrogen bonds and offered interesting information about the nature of the interactions between the aqueous surfactant solutions and curcumin depending on charge of head group of the surfactant. IL[bmin][BF 4] encouraged early formation of micelle in case of cationic and anionic aqueous surfactant solutions, but slightly prolonged micelle formation in the case of neutral aqueous surfactant solution. However, for curcumin IL [bmin][BF 4] favored strong association (7-fold increase) with neutral surfactant solution, marginally supported association with anionic surfactant solution and discouraged (˜2-fold decrease) association with cationic surfactant solution.

  12. Ionic liquid-assisted sonochemical preparation of CeO2 nanoparticles for CO oxidation

    DOE PAGESBeta

    Alammar, Tarek; Noei, Heshmat; Wang, Yuemin; Grünert, Wolfgang; Mudring, Anja -Verena

    2014-10-10

    CeO2 nanoparticles were synthesized via a one-step ultrasound synthesis in different kinds of ionic liquids based on bis(trifluoromethanesulfonylamide, [Tf2N]–, in combination with various cations including 1-butyl-3-methylimidazolium ([C4mim]+), 1-ethyl-2,3-dimethylimidazolium ([Edimim]+), butyl-pyridinium([Py4]+), 1-butyl-1-methyl-pyrrolidinium ([Pyrr14]+), and 2-hydroxyethyl-trimethylammonium ([N1112OH]+). Depending on synthetic parameters, such as ionic liquid, Ce(IV) precursor, heating method, and precipitator, formed ceria exhibits different morphologies, varying from nanospheres, nanorods, nanoribbons, and nanoflowers. The morphology, crystallinity, and chemical composition of the obtained materials were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), energy dispersive X-ray spectroscopy (EDX), Raman spectroscopy, and N2 adsorption. The structural and electronic propertiesmore » of the as-prepared CeO2 samples were probed by CO adsorption using IR spectroscopy under ultrahigh vacuum conditions. The catalytic activities of CeO2 nanoparticles were investigated in the oxidation of CO. CeO2 nanospheres obtained sonochemically in [C4mim][Tf2N] exhibit the best performance for low-temperature CO oxidation. As a result, the superior catalytic performance of this material can be related to its mesoporous structure, small particle size, large surface area, and high number of surface oxygen vacancy sites.« less

  13. Charge engineering of cellulases improves ionic liquid tolerance and reduces lignin inhibition.

    PubMed

    Nordwald, Erik M; Brunecky, Roman; Himmel, Michael E; Beckham, Gregg T; Kaar, Joel L

    2014-08-01

    We report a novel approach to concurrently improve the tolerance to ionic liquids (ILs) as well as reduce lignin inhibition of Trichoderma reesei cellulase via engineering enzyme charge. Succinylation of the cellulase enzymes led to a nearly twofold enhancement in cellulose conversion in 15% (v/v) 1-butyl-3-methylimidazolium chloride ([BMIM][Cl]). The improvement in activity upon succinylation correlated with the apparent preferential exclusion of the [Cl] anion in fluorescence quenching assays. Additionally, modeling analysis of progress curves of Avicel hydrolysis in buffer indicated that succinylation had a negligible impact on the apparent KM of cellulase. As evidence of reducing lignin inhibition of T. reesei cellulase, succinylation resulted in a greater than twofold increase in Avicel conversion after 170 h in buffer with 1 wt% lignin. The impact of succinylation on lignin inhibition of cellulase further led to the reduction in apparent KM of the enzyme cocktail for Avicel by 2.7-fold. These results provide evidence that naturally evolved cellulases with highly negative surface charge densities may similarly repel lignin, resulting in improved cellulase activity. Ultimately, these results underscore the potential of rational charge engineering as a means of enhancing cellulase function and thus conversion of whole biomass in ILs. PMID:24522957

  14. Molecular dynamics investigation of the ionic liquid/enzyme interface: application to engineering enzyme surface charge.

    PubMed

    Burney, Patrick R; Nordwald, Erik M; Hickman, Katie; Kaar, Joel L; Pfaendtner, Jim

    2015-04-01

    Molecular simulations of the enzymes Candida rugosa lipase and Bos taurus α-chymotrypsin in aqueous ionic liquids 1-butyl-3-methylimidazolium chloride and 1-ethyl-3-methylimidazolium ethyl sulfate were used to study the change in enzyme-solvent interactions induced by modification of the enzyme surface charge. The enzymes were altered by randomly mutating lysine surface residues to glutamate, effectively decreasing the net surface charge by two for each mutation. These mutations resemble succinylation of the enzyme by chemical modification, which has been shown to enhance the stability of both enzymes in ILs. After establishing that the enzymes were stable on the simulated time scales, we focused the analysis on the organization of the ionic liquid substituents about the enzyme surface. Calculated solvent charge densities show that for both enzymes and in both solvents that changing positively charged residues to negative charge does indeed increase the charge density of the solvent near the enzyme surface. The radial distribution of IL constituents with respect to the enzyme reveals decreased interactions with the anion are prevalent in the modified systems when compared to the wild type, which is largely accompanied by an increase in cation contact. Additionally, the radial dependence of the charge density and ion distribution indicates that the effect of altering enzyme charge is confined to short range (≤1 nm) ordering of the IL. Ultimately, these results, which are consistent with that from prior experiments, provide molecular insight into the effect of enzyme surface charge on enzyme stability in ILs. PMID:25641162

  15. When do defectless alkanethiol SAMs in ionic liquids become penetrable? A molecular dynamics study.

    PubMed

    Kislenko, Sergey A; Nikitina, Victoria A; Nazmutdinov, Renat R

    2015-12-21

    Molecular dynamics simulations were performed to address the permeability of defectless alkanethiol self-assembled monolayers (SAMs) on charged and uncharged Au(111) surfaces in 1-butyl-3-methylimidazolium ([bmim][BF4]) room-temperature ionic liquid (IL). We demonstrate that ionic permeation into the monolayer does not start until a critical surface charge density value is attained (both for positive and negative surface charges). The free energy barrier for the permeation of IL components is shown to include nearly equal contributions from ion desolvation and the channel formation in the dense monolayer. Long chain alkanethiols (hexadecanethiol SC16H33) exhibit superior barrier properties as compared with short chain alkanethiols (hexanethiol SC6H13) due to the dense packing of alkanethiol chains in highly ordered zigzag conformation oriented at the same tilt angle. Computed critical charge densities correspond to the electrode potential values beyond the limits of the monolayer stability, which might indicate the impermeability of the defectless monolayer towards the IL components. Experimental findings on increased interfacial capacitance are interpreted, therefore as some manifestation of the monolayer defectiveness occurring in real electrochemical systems. The potential of the mean force is constructed for a typical redox probe ferrocene/ferrocenium (Fc/Fc(+)) as well, to investigate a possible permeation of the solute from the IL into the SC6H13 monolayer. PMID:26568158

  16. Monolithic column incorporated with lanthanide metal-organic framework for capillary electrochromatography.

    PubMed

    Zhang, Li-Shun; Du, Pei-Yao; Gu, Wen; Zhao, Qing-Li; Huang, Yan-Ping; Liu, Zhao-Sheng

    2016-08-26

    A new lanthanide metal-organic frameworks NKU-1 have successfully incorporated into poly (BMA-co-EDMA) monolith and evaluated by capillary electrochromatography (CEC). Lanthanide metal-organic frameworks [Eu2(ABTC)1.5(H2O)3(DMA)] (NKU-1) were synthesized by self-assembly of Eu(III) ions and 3,3',5,5'-azo benzene tetracarboxylic acid ligands have been fabricated into poly(BMA-co-EDMA) monoliths. 1-Butyl-3-methylimidazolium tetrafluoroborate and N,N-dimethylformamide were developed as binary porogen obtaining homogeneous dispersibility for NKU-1 and high permeability for monolithic column. The successful incorporation of NKU-1 into poly(BMA-co-EDMA) was confirmed and characterized by FT-IR spectra, scanning electron microscopy, X-ray diffraction, energy dispersive spectrometer area scanning, and transmission electron microscopy. Separation ability of the NKU-1-poly (BMA-co-EDMA) monoliths was demonstrated by separating four groups of analytes in CEC, including alkylbenzenes, polycyclic aromatic hydrocarbon, aniline series and naphthyl substitutes. Compared with bare monolithic (column efficiency of 100,000plates/m), the NKU-1-poly (BMA-co-EDMA) monoliths have displayed greater column efficiency (maximum 210,000plates/m) and higher permeability, as well as less peak tailing. The results showed that the NKU-1-poly (BMA-co-EDMA) monoliths are promising stationary phases for CEC separations. PMID:27432788

  17. Solvent effects on the polar network of ionic liquid solutions

    NASA Astrophysics Data System (ADS)

    Bernardes, Carlos E. S.; Shimizu, Karina; Canongia Lopes, José N.

    2015-05-01

    Molecular dynamics simulations were used to probe mixtures of ionic liquids (ILs) with common molecular solvents. Four types of systems were considered: (i) 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide plus benzene, hexafluorobenzene or 1,2-difluorobenzene mixtures; (ii) choline-based ILs plus ether mixtures (iii) choline-based ILs plus n-alkanol mixtures; and (iv) 1-butyl-3-methylimidazolium nitrate and 1-ethyl-3-methylimidazolium ethyl sulfate aqueous mixtures. The results produced a wealth of structural and aggregation information that highlight the resilience of the polar network of the ILs (formed by clusters of alternating ions and counter-ions) to the addition of different types of molecular solvent. The analysis of the MD data also shows that the intricate balance between different types of interaction (electrostatic, van der Waals, H-bond-like) between the different species present in the mixtures has a profound effect on the morphology of the mixtures at a mesoscopic scale. In the case of the IL aqueous solutions, the present results suggest an alternative interpretation for very recently published x-ray and neutron diffraction data on similar systems.

  18. Effects of Room-Temperature Ionic Liquids on Zebra Mussels (Dreissena polymorpha)

    NASA Astrophysics Data System (ADS)

    Costello, D. M.; Bernot, R. J.; Lamberti, G. A.

    2005-05-01

    Zebra mussels (Dreissena polymorpha) are exotic bivalves that are widely distributed in eastern North America. We propose that this nuisance organism could serve as a model species for studies of aquatic toxicology. We tested zebra mussels response to room-temperature ionic liquids (ILs), which are being synthesized as environmentally friendly alternatives to volatile organic solvents. Volatile organic solvents contribute to atmospheric pollution and ozone depletion, whereas ILs are non-volatile and less harmful to the atmosphere. Although ILs would contribute significantly less to air pollution, little is known about their potential effects on aquatic ecosystems. In 72-hour toxicity tests, we determined the acute effects of three imidazolium-based ILs (1-butyl-3-methylimidazolium bromide (bmimBr), 1-hexyl-3-methylimidazolium bromide (hmimBr), and 1-octyl-3-methylimidazolium bromide (omimBr)) on the survival of zebra mussels. As alkyl chain length decreased, median lethal concentration (LC50) decreased from 1291 mg L-1 for bmimBr, to 105 mg L-1 for hmimBr, and 21.2 mg L-1 for omimBr. For bivalve mussels, the toxicities of these ILs are comparable to the toxicities of commonly used industrial solvents (e.g., toluene, benzene). This study presents a foundation for using zebra mussels in toxicity studies as well as possible models for less common Unionid mussels.

  19. Influence of PVP template on the formation of porous TiO2 nanofibers by electrospinning technique for dye-sensitized solar cell

    NASA Astrophysics Data System (ADS)

    Elayappan, Vijayakumar; Panneerselvam, Pratheep; Nemala, Sivasankar; Nallathambi, Karthick S.; Angaiah, Subramania

    2015-09-01

    The porous TiO2 nanofibers were prepared by electrospinning technique using polyvinylpyrrolidone (PVP) as template as well as pore-forming agent at the calcination temperature of 475 °C for 5 h. The influence of various concentrations of PVP (5, 8 and 10 wt%) on the surface area and porosity of the prepared TiO2 nanofibers (NFs) were studied by using BET-specific surface area analyzer. The TiO2 NFs obtained by using 5 wt% of PVP had higher surface area and porosity than those obtained by using 8 and 10 wt% of PVP. The prepared electrospun TiO2 NFs were characterized by using TG analysis, X-ray diffraction, FTIR, FE-SEM and TEM studies. Finally, dye-sensitized solar cells were assembled using the prepared TiO2 NFs as the photoanode, Pt as the cathode and 0.5 M 1-butyl-3-methylimidazolium iodide, 0.5 M LiI, 0.05 M I2, 0.5 M 4-tertbutylpyridine in acetonitrile as an electrolyte. Among the three photoanodes, the cell assembled using porous TiO2 NFs obtained by using 5 wt% of PVP showed higher power conversion efficiency (PCE) of 4.81 % than those obtained by using 8 and 10 wt% of PVP, which showed the lower PCE of 4.13 and 3.42 %, respectively.

  20. Direct Synthesis of Controlled-Size Nanospheres inside Nanocavities of Self-Organized Photopolymerizing Soft Oxometalates [PW12 O40 ]n (n=1100-7500).

    PubMed

    Das, Kousik; Roy, Soumyajit

    2015-09-01

    The unusual self-assembly of {(BMIm)2 (DMIm)[PW12 O40 ]}n (n=1100-7500) (BMIm=1-butyl-3-methylimidazolium, DMIm=3,3'-dimethyl-1,1'-diimidazolium) soft oxometalates (SOMs) with controlled size and a hollow nanocavity was exploited for the photochemical synthesis of polymeric nanospheres within the nanocavity of the SOM. The SOM vesicle has been characterized by using several techniques, including dynamic light scattering (DLS), static light scattering (SLS), attenuated total reflection (ATR) IR spectroscopy, Raman spectroscopy, microscopy, and zeta-potential analysis. The self-assembly and stabilization of this soft-oxometalate vesicle has been shown by means of counter-ion condensation. The immediate implication of such stabilization-the variation of the dielectric constant with the hydrodynamic radius of the vesicle-has been used to synthesize vesicles of controlled size. Such vesicles of varying size have been used as templates for polymerization reactions that produce polymeric spheres of controlled size. Direct evidence shows that the SOM behaves as a model heterogeneous catalytic system. Such surfactant- and initiator-free photochemical synthetic routes for obtaining uniform latex spheres could be used in the making of optical bandgap materials, inverse opals, and paints. PMID:26185037

  1. Two solid-phase recycling method for basic ionic liquid [C4mim]Ac by macroporous resin and ion exchange resin from Schisandra chinensis fruits extract.

    PubMed

    Ma, Chun-hui; Zu, Yuan-gang; Yang, Lei; Li, Jian

    2015-01-22

    In this study, two solid-phase recycling method for basic ionic liquid (IL) 1-butyl-3-methylimidazolium acetate ([C4mim]Ac) were studied through a digestion extraction system of extracting biphenyl cyclooctene lignans from Schisandra chinensis. The RP-HPLC detection method for [C4mim]Ac was established in order to investigate the recovery efficiency of IL. The recycling method of [C4mim]Ac is divided into two steps, the first step was the separation of lignans from the IL solution containing HPD 5000 macroporous resin, the recovery efficiency and purity of [C4mim]Ac achieved were 97.8% and 67.7%, respectively. This method cannot only separate the lignans from [C4mim]Ac solution, also improve the purity of lignans, the absorption rate of lignans in [C4mim]Ac solution was found to be higher (69.2%) than that in ethanol solution (57.7%). The second step was the purification of [C4mim]Ac by the SK1B strong acid ion exchange resin, an [C4mim]Ac recovery efficiency of 55.9% and the purity higher than 90% were achieved. Additionally, [C4mim]Ac as solvent extraction of lignans from S. chinensis was optimized, the hydrolysis temperature was 90°C and the hydrolysis time was 2h. PMID:25463641

  2. Molecularly imprinted polymers for the solid-phase extraction of four fluoroquilones from milk and lake water samples.

    PubMed

    Wu, Xi; Wu, Lintao

    2015-10-01

    A method based on molecular crowding and ionic liquids as reaction solvents has been used for the synthesis of molecularly imprinted polymers. Levofloxacin was selected as the template, polymethyl methacrylate was the molecular crowding agent, and 1-butyl-3-methylimidazolium tetrafluoroborate (ionic liquid) was selected as the reaction solvent and porogen. The optimized proportion for the mixed porogen was dimethyl sulfoxide/ionic liquid/polymethyl methacrylate 1:1.6:5 in chloroform (150 mg mL(-1) ). The morphology and chemical composition of levofloxacin imprinted polymers were assessed by scanning electron microscopy and Fourier transform infrared spectroscopy. The absorption experiments demonstrated that the levofloxacin imprinted polymers possess high selective recognition property to levofloxacin and analogs, including enrofloxacin, ciprofloxacin and gatifloxacin, which all belong to fluoroquinolones. An extraction method using levofloxacin imprinted polymers as sorbent followed by high-performance liquid chromatography analysis was optimized for the determination of four fluoroquinolones in milk and lake water samples. Under the optimized conditions, good linearity was observed in a range of 5-1000 ng g(-1) with the limit of detection between 0.3 and 0.5 ng g(-1) for the four fluoroquinolones. The recoveries at three spiked levels ranged 82.4-98.3% with the relative standard deviation ≤4.9. PMID:26418224

  3. Significantly improving enzymatic saccharification of high crystallinity index's corn stover by combining ionic liquid [Bmim]Cl-HCl-water media with dilute NaOH pretreatment.

    PubMed

    He, Yu-Cai; Liu, Feng; Gong, Lei; Zhu, Zheng-Zhong; Ding, Yun; Wang, Cheng; Xue, Yu-Feng; Rui, Huan; Tao, Zhi-Cheng; Zhang, Dan-Ping; Ma, Cui-Luan

    2015-01-01

    In this study, a pretreatment by combining acidified aqueous ionic liquid 1-butyl-3-methylimidazolium chloride (IL [Bmim]Cl) solution with dilute NaOH extraction was employed to pretreat high crystallinity index (CrI) of corn stover before its enzymatic saccharification. After NaOH extraction, [Bmim]Cl-HCl-water (78.8:1.2:20, w/w/w) media was used for further pretreatment at 130 °C for 30 min. After being enzymatically hydrolyzed for 48 h, corn stover pretreated could be biotransformed into reducing sugars in the yield of 95.1%. Furthermore, SEM, XRD and FTIR analyses of untreated and pretreated corn stovers were examined. It was found that the intact structure was disrupted by combination pretreatment and resulted in a porous and amorphous regenerated cellulosic material that greatly improved enzymatic hydrolysis. Finally, the recovered hydrolyzates obtained from the enzymatic hydrolysis of pretreated corn stovers could be fermented into ethanol efficiently. In conclusion, the combination pretreatment shows high potential application in future. PMID:25921785

  4. Matrix solid-phase dispersion coupled with magnetic ionic liquid dispersive liquid-liquid microextraction for the determination of triazine herbicides in oilseeds.

    PubMed

    Wang, Yuanpeng; Sun, Ying; Xu, Bo; Li, Xinpei; Wang, Xinghua; Zhang, Hanqi; Song, Daqian

    2015-08-12

    A novel method was developed for the determination of six triazine herbicides from oilseeds by matrix solid-phase dispersion combined with magnetic ionic liquid dispersive liquid-liquid microextraction (MSPD-MIL-DLLME), followed by ultrafast liquid chromatography with ultraviolet detection (UFLC-UV). The MIL, 1-butyl-3-methylimidazolium tetrachloroferrate ([C4mim][FeCl4]), was used as the microextraction solvent to simplify the extraction procedure by magnetic separation. The effects of several important experimental parameters, including type of dispersant, ratio of sample to dispersant, type and volume of collected elution solvent, type and volume of MIL, were investigated. Using the present method, UFLC-UV gave the limits of detection (LODs) of 1.20-2.72 ng g(-1) and the limits of quantification (LOQs) of 3.99-9.06 ng g(-1) for triazine herbicides. The recoveries were ranged from 82.9 to 113.7% and the relative standard deviations (RSDs) were equal or lower than 7.7%. The present method is easy-to-use and effective for extraction of triazine herbicides from oilseeds and shows the potentials of practical applications in the treatment of the fatty solid samples. PMID:26320960

  5. Sulfonic Acid- and Lithium Sulfonate-Grafted Poly(Vinylidene Fluoride) Electrospun Mats As Ionic Liquid Host for Electrochromic Device and Lithium-Ion Battery.

    PubMed

    Zhou, Rui; Liu, Wanshuang; Leong, Yew Wei; Xu, Jianwei; Lu, Xuehong

    2015-08-01

    Electrospun polymer nanofibrous mats loaded with ionic liquids (ILs) are promising nonvolatile electrolytes with high ionic conductivity. The large cations of ILs are, however, difficult to diffuse into solid electrodes, making them unappealing for application in some electrochemical devices. To address this issue, a new strategy is used to introduce proton conduction into an IL-based electrolyte. Poly(vinylidene fluoride-co-hexafluoropropylene) (P(VDF-HFP)) copolymer is functionalized with sulfonic acid through covalent attachment of taurine. The sulfonic acid-grafted P(VDF-HFP) electrospun mats consist of interconnected nanofibers, leading to remarkable improvement in dimensional stability of the mats. IL-based polymer electrolytes are prepared by immersing the modified mats in 1-butyl-3-methylimidazolium tetrafluoroborate (BMIM(+)BF4(-)). It is found that the SO3(-) groups can have Lewis acid-base interactions with the cations (BMIM(+)) of IL to promote the dissociation of ILs, and provide additional proton conduction, resulting in significantly improved ionic conductivity. Using this novel electrolyte, polyaniline-based electrochromic devices show higher transmittance contrast and faster switching behavior. Furthermore, the sulfonic acid-grafted P(VDF-HFP) electrospun mats can also be lithiated, giving additional lithium ion conduction for the IL-based electrolyte, with which Li/LiCoO2 batteries display enhanced C-rate performance. PMID:26167794

  6. Direct UV-spectroscopic measurement of selected ionic-liquid vapors

    SciTech Connect

    Dai, Sheng; Luo, Huimin; Wang, Congmin; Li, Haoran

    2010-01-01

    The hallmark of ionic liquids lies in their negligible vapor pressure. This ultralow vapor pressure makes it difficult to conduct the direct spectroscopic measurement of ionic-liquid vapors. In fact, there have been no electronic spectroscopic data currently available for ionic-liquid vapors. This deficiency significantly hampers the fundamental understanding of the unique molecular structures of ionic liquids. Herein, the UV absorption spectra of eight ionic liquids, such as 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([Bmim{sup +}] [Tf{sub 2}N{sup -}]) and 1-ethyl-3-methylimidazolium bis(perfluoroethylsulfonyl)imide ([Emim{sup +}][beti{sup -}]) in the vapor phase in a distillation-like environment, were measured through a high-temperature spectroscopic technique to fill this knowledge gap. Two strong absorption peaks of the [Bmim{sup +}][Tf{sub 2}N{sup -}] vapor lie at 202 and 211 nm, slightly different from those of the neat [Bmim{sup +}][Tf{sub 2}N{sup -}] thin film and its solution in water. Based on the quantitative determination of the vapor absorption spectra as a function of temperature, the vaporization enthalpies of these ionic liquids vapors were measured and found to be in good agreement with the corresponding literature values. This in situ method opens up a new avenue to study the nature of ionic-liquid vapors and to determine the vaporization enthalpies of ionic liquids.

  7. Pesticide Removal from Aqueous Solutions by Adding Salting Out Agents

    PubMed Central

    Moscoso, Fátima; Deive, Francisco J.; Esperança, José M. S. S.; Rodríguez, Ana

    2013-01-01

    Phase segregation in aqueous biphasic systems (ABS) composed of four hydrophilic ionic liquids (ILs): 1-butyl-3-methylimidazolium methylsulfate and 1-ethyl-3-methylimidazolium methylsulfate (CnC1im C1SO4, n = 2 and 4), tributylmethyl phosphonium methylsulfate (P4441 C1SO4) and methylpyridinium methylsulfate (C1Py C1SO4) and two high charge density potassium inorganic salts (K2CO3 and K2HPO4) were determined by the cloud point method at 298.15 K. The influence of the addition of the selected inorganic salts to aqueous mixtures of ILs was discussed in the light of the Hofmeister series and in terms of molar Gibbs free energy of hydration. The effect of the alkyl chain length of the cation on the methylsulfate-based ILs has been investigated. All the solubility data were satisfactorily correlated to several empirical equations. A pesticide (pentachlorophenol, PCP) extraction process based on the inorganic salt providing a greater salting out effect was tackled. The viability of the proposed process was analyzed in terms of partition coefficients and extraction efficiencies. PMID:24145747

  8. Conformational and Dynamic Properties of Poly(ethylene oxide) in an Ionic Liquid: Development and Implementation of a First-Principles Force Field.

    PubMed

    McDaniel, Jesse G; Choi, Eunsong; Son, Chang-Yun; Schmidt, J R; Yethiraj, Arun

    2016-01-14

    The conformational properties of polymers in ionic liquids are of fundamental interest but not well understood. Atomistic and coarse-grained molecular models predict qualitatively different results for the scaling of chain size with molecular weight, and experiments on dilute solutions are not available. In this work, we develop a first-principles force field for poly(ethylene oxide) (PEO) in the ionic liquid 1-butyl 3-methylimidazolium tetrafluoroborate ([BMIM][BF4]) using symmetry adapted perturbation theory (SAPT). At temperatures above 400 K, simulations employing both the SAPT and OPLS-AA force fields predict that PEO displays ideal chain behavior, in contrast to previous simulations at lower temperature. We therefore argue that the system shows a transition from extended to more compact configurations as the temperature is increased from room temperature to the experimental lower critical solution temperature. Although polarization is shown to be important, its implicit inclusion in the OPLS-AA force is sufficient to describe the structure and energetics of the mixture. The simulations emphasize the difference between ionic liquids from typical solvents for polymers. PMID:26690901

  9. Fluoroquinolone antibiotic determination in bovine, ovine and caprine milk using solid-phase extraction and high-performance liquid chromatography-fluorescence detection with ionic liquids as mobile phase additives.

    PubMed

    Herrera-Herrera, Antonio V; Hernández-Borges, Javier; Rodríguez-Delgado, Miguel Angel

    2009-10-23

    This paper describes the use of 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIm-BF(4)) as mobile phase additive for the analysis by high-performance liquid chromatography with fluorescence detection of a group of seven basic fluoroquinolone antibiotics (i.e. fleroxacin, ciprofloxacin, lomefloxacin, danofloxacin, enrofloxacin, sarafloxacin and difloxacin) in different milk samples. EMIm-BF(4) was found superior to 1-butyl-3-methylimidazolium tetrafluoroborate for the separation of the analytes from chromatographic interferences of the sample matrix. The optimized method was applied to the analysis of ovine, caprine and bovine milk, in the last case in either skimmed, semi-skimmed and full-cream milk after suitable acidic deproteination followed by a solid-phase extraction procedure. Recovery values between 73% and 113% were obtained for the three types of bovine milk samples, as well as for ovine and caprine milk (RSDs below 16% in all cases), which clearly demonstrates the applicability of the method to the three types of milk irrespective of the fat content of the samples. Limits of detection were in the range of 0.5-8.1 microg/L (approximately 0.5-25.9 microg/kg), well below the maximum residue limits established for these compounds by the current European legislation. A screening study of 24 different milk samples was also developed. In none of the samples, residues of the selected antibiotics were found. PMID:19268960

  10. New Alkylether-Thiazolium Room-Temperature Ionic Liquid Lubricants: Surface Interactions and Tribological Performance.

    PubMed

    Espinosa, Tulia; Sanes, José; Bermúdez, María-Dolores

    2016-07-20

    The use of newly synthesized alkylether-thiazolium ionic liquids as lubricants is described for the first time. Two ionic liquids composed of a thiazolium cation and a bis(trifluoromethanesulfonyl)amide ([Th][Tf2N]) or dicyanamide ([Th][(NC)2N]) anion have been studied, and their tribological behavior has been compared with that of 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)amide ([Im][Tf2N]) in pin-on-disk tests using sapphire balls against AISI 52100 or AISI 316L steels. All ionic liquids show higher contact angles on AISI 316L steel than on AISI 52100, the lowest values found for ([Im][Tf2N]) on both steel surfaces. AISI 52100 shows similar friction coefficients for all lubricants, and negligible wear rates for the ionic liquids containing the bis(trifluoromethanesulfonyl)amide anion. Immersion tests show no corrosion of AISI 52100 in imidazolium or thiazolium bis(trifluoromethanesulfonyl)amide ionic liquids. AISI 316L shows similar friction coefficients for both bis(trifluoromethanesulfonyl)amide ionic liquids, but the lowest wear rate is obtained for [Th][Tf2N]. An increase in friction coefficient and wear rate is observed for thiazolium dicyanamide. This increase is related to a tribocorrosion process due to decomposition of the thiazolium cation. XPS shows the formation of iron sulfide on the wear track on AISI 316L after lubrication with thiazolium dicyanamide. No tribocorrosion processes take place for the [Tf2N] ionic liquids. PMID:27348604

  11. A metallacage encapsulating chloride as a probe for a solvation scale in ionic liquids.

    PubMed

    Daguenet, Corinne; Dyson, Paul J

    2007-01-22

    With the purpose of assessing the reactivity of chloride ions dissolved in ionic liquids (ILs), a relative scale for the solvation of chloride is given for a series of ILs based on the bis(trifluoromethane)sulfonimide ([Tf(2)N]) anion and different cations, 1-butyl-3-methylimidazolium ([bmim]), 1-butyl-2,3-dimethylimidazolium ([bdmim]), 1-butyl-1-methylpyrrolidinium ([bmpy]), 1-butylpyridinium ([bpy]), 1-pentyl-1,1,1-triethylammonium ([C(5)e(3)am]), and 1-(2-hydroxy)ethyl-3-methylimidazolium ([mimeOH]). Insights into the solvation of chloride are achieved by the thermodynamic study of the reaction of dissociation of a chloride-templated nickel(II) metallacage performed at various temperatures by UV-visible spectroscopy in each IL. The order of chloride solvation [C(5)e(3)am][Tf(2)N] < [bmpy][Tf(2)N] < [bmim][Tf(2)N]

  12. Ionic Liquid Extractions of Soil Organic Matter

    NASA Astrophysics Data System (ADS)

    Patti, Antonio; Macfarlane, Douglas; Clarke, Michael

    2010-05-01

    A large range of ionic liquids with the ability to dissolve different classes of natural biopolymers (e.g. cellulose, lignin, protein) have been reported in the literature. These have the potential to isolate different fractions of soil organic matter, thus yielding novel information that is not available through other extraction procedures. The ionic liquids dimethylammonium dimethylcarbamate (DIMCARB), alkylbenzenesulfonate and 1-butyl-3methylimidazolium chloride (Bmim Cl) can solubilise selected components of soil organic matter. Soil extractions with these materials showed that the organic matter recovered showed chemical properties that were consistent with humic substances. These extracts had a slightly different organic composition than the humic acids extracted using the traditional International Humic Substances Society (IHSS) method. The ionic liquids also solubilised some inorganic matter from the soil. Humic acids recovered with alkali were also partially soluble in the ionic liquids. DIMCARB appeared to chemically interfere with organic extract, increasing the level of nitrogen in the sample. It was concluded that the ionic liquid Bmim Cl may function as a useful solvent for SOM, and may be used to recover organic matter of a different character to that obtained with alkali

  13. Morphology- and facet-controlled synthesis of CuO micro/nanomaterials and analysis of their lithium ion storage properties

    NASA Astrophysics Data System (ADS)

    Liu, Xiaodi; Liu, Guangyin; Wang, Lijuan; Li, Yinping; Ma, Yupei; Ma, Jianmin

    2016-04-01

    Hierarchical CuO architectures and monodisperse CuO nanoplates are synthesized via a hydrothermal method with the assistance of ionic liquid 1-butyl-3-methylimidazolium chloride ([Bmim]Cl). The products are characterized by XRD, SEM, TEM, HRTEM, BET, and XPS, and the results indicate that the CuO architectures are composed of nanosheets with exposed (001) facets and the CuO nanoplates are single crystals enclosed by (200) facets. More specially, it is found that [Bmim]Cl serves as an effective template for the synthesis of CuO nanoplates by adsorbing on the (200) planes of monoclinic CuO. When evaluated as anode materials for lithium-ion batteries, CuO architectures possess higher discharge capacity, better cycling stability, and better rate capability than CuO nanoplates. The initial discharge capacity of CuO architectures is 1096 mAh g-1 at a rate of 0.5 C, whereas CuO nanoplates exhibit a lower capacity of 878.4 mAh g-1. Moreover, after 50 cycles, CuO architectures and CuO nanoplates can deliver discharge capacities of 465.6 and 281.6 mAh g-1, respectively.

  14. Tuning the theta temperature and critical micellization temperature of polymers in ionic liquids

    NASA Astrophysics Data System (ADS)

    Lodge, Timothy; Hoarfrost, Megan

    2014-03-01

    Ionic liquids feature a combination of properties that make them very interesting solvents for polymers, but questions remain regarding the thermodynamics of polymer/ionic liquid solutions. In this work, the lower-critical-solution-temperature (LCST) phase behavior of poly(n-butyl methacrylate) (PnBMA) in mixtures of the ionic liquids 1-butyl-3-methylimidazolium: bis(trifluoromethylsulfonyl)imide ([BMIm][TFSI]) and 1-ethyl-3-methylimidazolium:TFSI ([EMIm][TFSI]) is characterized by transmittance, light scattering, and small-angle neutron scattering measurements. Relevant thermodynamic parameters are readily tuned by varying the ionic liquid composition. In particular, the cloud point, spinodal, and theta temperatures are all found to increase linearly with [BMIm] content. The interaction parameters are determined as a function of temperature and concentration using three different methods, and the results from each method are compared. The theta temperatures are then compared quantitatively to the critical micellization temperatures (CMTs) for PnBMA-poly(ethylene oxide) diblocks, to test the proposition that the CMT corresponds to a fixed value of chi.

  15. Charging and aggregation of latex particles in aqueous solutions of ionic liquids: towards an extended Hofmeister series.

    PubMed

    Oncsik, Tamas; Desert, Anthony; Trefalt, Gregor; Borkovec, Michal; Szilagyi, Istvan

    2016-03-01

    The effect of ionic liquid (IL) constituents and other monovalent salts on the stability of polystyrene latex particles was studied by electrophoresis and light scattering in dilute aqueous suspensions. The surface charge and the aggregation rate were both sensitive to the type of ion leading to different critical coagulation concentration (CCC) values. Systematic variation of the type of IL cation and anion allows us to place these ions within the Hofmeister series. We find that the dicyanoamide anion should be placed between iodide and thiocyanate, while all 1-alkyl-3-methylimidazolium cations can be positioned to the left of the tetramethylammonium and ammonium ions. The hydrophobicity of the 1-butyl-1-methylpyrrolidinium (BMPL(+)) ion is intermediate between 1-ethyl-3-methylimidazolium (EMIM(+)) and 1-butyl-3-methylimidazolium (BMIM(+)). With increasing alkyl chain length, the 1-alkyl-3-methylimidazolium cations adsorb on the latex particles very strongly, and 1-hexyl-3-methylimidazolium (HMIM(+)) and 1-octyl-3-methylimidazolium (OMIM(+)) lead to pronounced charge reversal and to an intermediate restabilization region. PMID:26902948

  16. Effects of Oxygen-Containing Functional Groups on Supercapacitor Performance

    SciTech Connect

    Kerisit, Sebastien N.; Schwenzer, Birgit; Vijayakumar, M.

    2014-07-03

    Molecular dynamics (MD) simulations of the interface between graphene and the ionic liquid 1-butyl-3-methylimidazolium trifluoromethanesulfonate (BMIM OTf) were carried out to gain molecular-level insights into the performance of graphene-based supercapacitors and, in particular, determine the effects of the presence of oxygen-containing defects at the graphene surface on their integral capacitance. The MD simulations predict that increasing the surface coverage of hydroxyl groups negatively affects the integral capacitance, whereas the effect of the presence of epoxy groups is much less significant. The calculated variations in capacitance are found to be directly correlated to the interfacial structure. Indeed, hydrogen bonding between hydroxyl groups and SO3 anion moieties prevents BMIM+ and OTf- molecules from interacting favorably in the dense interfacial layer and restrains the orientation and mobility of OTf- ions, thereby reducing the permittivity of the ionic liquid at the interface. The results of the molecular simulations can facilitate the rational design of electrode materials for supercapacitors.

  17. Ionic Liquid-Assisted Hydrothermal Method Synthesis of Flower-Like MoS2 and Their Electrochemical Performances.

    PubMed

    Li, Maohua; Yang, Bo; Hao, Junying; Lu, Yi; Long, Zerong; Liu, Yumei

    2016-06-01

    Molybdenum disulfide (MoS2) was prepared successfully via hydrothermal reaction at 200 degrees C in water/ethanol (1:1) solvent system using the ammonium molybdate and sodium thiosulfate as the molybdenum sources and sulfur sources, 1-butyl-3-methylimidazolium chloride salt [BMIM][Cl] as the additive agent. The scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to examine the morphology and structure of flower-like products. X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy spectrum analysis results show that the as-prepared product is a pure phase of MoS2. The prepared products are used as electrode materials for Li-ion batteries and showed excellent cycle stability and high Coulombic efficiency at a current density of 200 mA x g(-1) in the voltage range of 0.01 - 3.00 V (vs. Li/Li+). In addition, this paper also examined the influence of the reaction time and the amount of template agent on morphology, and discussed the reaction mechanism of the formation of flower-like morphology. PMID:27427696

  18. Theoretical Elucidation of Glucose Dehydration to 5-Hydroxymethylfurfural Catalyzed by a SO3H-Functionalized Ionic Liquid.

    PubMed

    Li, Jingjing; Li, Jinghua; Zhang, Dongju; Liu, Chengbu

    2015-10-22

    While the catalytic conversion of glucose to 5-hydroxymethyl furfural (HMF) catalyzed by SO3H-functioned ionic liquids (ILs) has been achieved successfully, the relevant molecular mechanism is still not understood well. Choosing 1-butyl-3-methylimidazolium chloride [C4SO3HmimCl] as a representative of SO3H-functioned IL, this work presents a density functional theory (DFT) study on the catalytic mechanism for conversion of glucose into HMF. It is found that the conversion may proceed via two potential pathways and that throughout most of elementary steps, the cation of the IL plays a substantial role, functioning as a proton shuttle to promote the reaction. The chloride anion interacts with the substrate and the acidic proton in the imidazolium ring via H-bonding, as well as provides a polar environment together with the imidazolium cation to stabilize intermediates and transition states. The calculated overall barriers of the catalytic conversion along two potential pathways are 32.9 and 31.0 kcal/mol, respectively, which are compatible with the observed catalytic performance of the IL under mild conditions (100 °C). The present results provide help for rationalizing the effective conversion of glucose to HMF catalyzed by SO3H-functionalized ILs and for designing IL catalysts used in biomass conversion chemistry. PMID:26434955

  19. Three-phase catalytic system of H2O, ionic liquid, and VOPO4-SiO2 solid acid for conversion of fructose to 5-hydroxymethylfurfural.

    PubMed

    Tian, Chengcheng; Zhu, Xiang; Chai, Song-Hai; Wu, Zili; Binder, Andrew; Brown, Suree; Li, Lin; Luo, Huimin; Guo, Yanglong; Dai, Sheng

    2014-06-01

    Efficient transformation of biomass-derived feedstocks to chemicals and fuels remains a daunting challenge in utilizing biomass as alternatives to fossil resources. A three-phase catalytic system, consisting of an aqueous phase, a hydrophobic ionic-liquid phase, and a solid-acid catalyst phase of nanostructured vanadium phosphate and mesostructured cellular foam (VPO-MCF), is developed for efficient conversion of biomass-derived fructose to 5-hydroxymethylfurfural (HMF). HMF is a promising, versatile building block for production of value-added chemicals and transportation fuels. The essence of this three-phase system lies in enabling the isolation of the solid-acid catalyst from the aqueous phase and regulation of its local environment by using a hydrophobic ionic liquid, 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([BMIM][Tf2N]). This system significantly inhibits the side reactions of HMF with H2O and leads to 91 mol % selectivity to HMF at 89 % of fructose conversion. The unique three-phase catalytic system opens up an alternative avenue for making solid-acid catalyst systems with controlled and locally regulated microenvironment near catalytically active sites by using a hydrophobic ionic liquid. PMID:24729382

  20. Hydrolysis of cellulose catalyzed by novel acidic ionic liquids.

    PubMed

    Zhuo, Kelei; Du, Quanzhou; Bai, Guangyue; Wang, Congyue; Chen, Yujuan; Wang, Jianji

    2015-01-22

    The conversion of cellulosic biomass directly into valuable chemicals becomes a hot subject. Six novel acidic ionic liquids (ILs) based on 2-phenyl-2-imidazoline were synthesized and characterized by UV-VIS, TGA, and NMR. The novel acidic ionic liquids were investigated as catalysts for the hydrolysis of cellulose in 1-butyl-3-methylimidazolium chloride ([Bmim]Cl). The acidic ionic liquids with anions HSO4(-) and Cl(-) showed better catalytic performance for the hydrolysis of cellulose than those with H2PO4(-). The temperature and dosage of water affect significantly the yield of total reducing sugar (TRS). When the hydrolysis of cellulose was catalyzed by 1-propyl sulfonic acid-2-phenyl imidazoline hydrogensulfate (IL-1) and the dosage of water was 0.2g, the TRS yield was up to 85.1% within 60 min at 100°C. These new acidic ionic liquids catalysts are expected to have a wide application in the conversion of cellulose into valuable chemicals. PMID:25439867

  1. Catalytic conversion of carbohydrates into 5-hydroxymethylfurfural over cellulose-derived carbonaceous catalyst in ionic liquid.

    PubMed

    Hu, Lei; Zhao, Geng; Tang, Xing; Wu, Zhen; Xu, Jiaxing; Lin, Lu; Liu, Shijie

    2013-11-01

    Three environmental-benign and low-cost carbon-based solid acid catalysts containing -SO3H, -COOH and phenolic -OH groups were prepared and used for the conversion of glucose into 5-hydroxymethylfurfural (HMF) in ionic liquid 1-butyl-3-methylimidazolium chloride ([BMIM]Cl). The results demonstrated that cellulose-derived carbonaceous catalyst (CCC) possessed the highest catalytic activity, which resulted in 46.4% HMF yield at 160°C for only 15 min. In addition, the reaction kinetics for the conversion of glucose into HMF over CCC was fitted with the first-order rate equation. The slightly-deactivated CCC after four successive reaction runs could be easily regenerated by a simple carbonization and sulfonation process. More gratifyingly, the combination of CCC and [BMIM]Cl were confirmed to be suitable for converting other carbohydrates such as fructose, sucrose, maltose, cellobiose, starch and cellulose into HMF. Particularly, a plausible mechanism involving hydrolysis, isomerization and dehydration for the conversion of carbohydrates into HMF was also proposed. PMID:24090810

  2. Conversion of xylan, d-xylose and lignocellulosic biomass into furfural using AlCl3 as catalyst in ionic liquid.

    PubMed

    Zhang, Luxin; Yu, Hongbing; Wang, Pan; Dong, Heng; Peng, Xinhong

    2013-02-01

    In order to define a new green catalytic pathway for the production of furfural, the catalyzed conversion of xylan into furfural in 1-butyl-3-methylimidazolium chloride was studied by using mineral acids and metal chlorides as catalysts under microwave irradiation. Amongst these catalysts, AlCl(3) resulted in the highest furfural yield of 84.8% at 170°C for 10s. The effect of AlCl(3) on the conversion efficiency of d-xylose and untreated lignocellulosic biomass was also investigated, the yields of furfural from corncob, grass and pine wood catalyzed by AlCl(3) in [BMIM]Cl were in the range of 16-33%. [BMIM]Cl and AlCl(3) could be recycled for four runs with stable catalytic activity. AlCl(3) is less corrosive than mineral acids, and the use of ionic liquid as reaction medium will no longer generate toxic wastewater, thus this reaction system is more ecologically viable. PMID:23306118

  3. "One-step production of biodiesel from Jatropha oil with high-acid value in ionic liquids" [Bioresour. Technol. 102 (11) (2011)].

    PubMed

    Guo, Feng; Fang, Zhen; Tian, Xiao-fei; Long, Yun-Duo; Jiang, Li-Qun

    2013-07-01

    Catalytic conversion of un-pretreated Jatropha oil with high-acid value (13.8 mg KOH/g) to biodiesel was studied in ionic liquids (ILs) with metal chlorides. Several commercial ILs were used to catalyze the esterification of oleic acid. It was found that 1-butyl-3-methylimidazolium tosylate {[BMIm][TS]} had high catalytic activity with 93% esterification rate for oleic acid at 140 °C but only 63.7% Jatropha biodiesel yield at 200 °C. When ZnCl2 was added to [BMIm][TS], a maximum Jatropha biodiesel yield of 92.5% was achieved at 180 °C. Addition of metal ions supplied Lewis acidic sites in ILs promoted both esterification and transestrification reactions. It was also found that the transition metal ions performed higher catalytic activity in transestrification than the ions of Group A. Mixture of [BMIm][TS] and ZnCl2 was easily separated from products for reuse to avoid producing pollutants. PMID:23908993

  4. Conversion of fructose and glucose into 5-hydroxymethylfurfural with lignin-derived carbonaceous catalyst under microwave irradiation in dimethyl sulfoxide-ionic liquid mixtures.

    PubMed

    Guo, Feng; Fang, Zhen; Zhou, Tie-Jun

    2012-05-01

    5-Hydroxymethylfurfural (5-HMF) was successfully produced by the dehydration of fructose and glucose using lignin-derived solid acid catalyst in DMSO-[BMIM][Cl] (dimethyl sulfoxide and 1-butyl-3-methylimidazolium chloride) mixtures. Six solid acid catalysts were synthesized by carbonization and sulfonation of raw biomass materials, i.e., glucose, fructose, cellulose, lignin, bamboo and Jatropha hulls. It was found that lignin-derived solid acid catalyst (LCC) was the most active one in the dehydration of sugars. LCC coupled with microwave irradiation was used for the 5-HMF production, 84% 5-HMF yield with 98% fructose conversion rate was achieved at 110°C for 10 min. Furthermore, 99% glucose was converted with 68% 5-HMF yield under severer condition (160°C for 50 min). LCC was recycled for five times, 5-HMF yield declined only 7%. Use of LCC combined with DMSO-[BMIM][Cl] solution and microwave irradiation is a novel method for the effective production of 5-HMF. PMID:22429401

  5. One-step production of biodiesel from Jatropha oil with high-acid value in ionic liquids.

    PubMed

    Guo, Feng; Fang, Zhen; Tian, Xiao-Fei; Long, Yun-Duo; Jiang, Li-Qun

    2011-06-01

    Catalytic conversion of un-pretreated Jatropha oil with high-acid value (13.8 mg KOH/g) to biodiesel was studied in ionic liquids (ILs) with metal chlorides. Several commercial ILs were used to catalyze the esterification of oleic acid. It was found that 1-butyl-3-methylimidazolium tosylate ([BMIm][CH(3)SO(3)]; a Brønsted acidic IL) had the highest catalytic activity with 93% esterification rate for oleic acid at 140°C but only 12% biodiesel yield at 120°C. When FeCl(3) was added to [BMIm][CH(3)SO(3)], a maximum biodiesel yield of 99.7% was achieved at 120°C. Because metal ions in ILs supplied Lewis acidic sites, and more of the sites could be provided by trivalent metallic ions than those of bivalent ones. It was also found that the catalytic activity with bivalent metallic ions increased with atomic radius. Mixture of [BMIm][CH(3)SO(3)] and FeCl(3) was easily separated from products for reuse to avoid producing pollutants. PMID:21420854

  6. A Combined Experimental and Molecular Dynamics Study of Iodide-Based Ionic Liquid and Water Mixtures.

    PubMed

    Nickerson, Stella D; Nofen, Elizabeth M; Chen, Haobo; Ngan, Miranda; Shindel, Benjamin; Yu, Hongyu; Dai, Lenore L

    2015-07-16

    Iodide-based ionic liquids have been widely employed as iodide sources in electrolytes for applications utilizing the triiodide/iodide redox couple. While adding a low-viscosity solvent such as water to ionic liquids can greatly enhance their usefulness, mixtures of highly viscous iodide-containing ILs with water have never been studied. This paper investigates, for the first time, mixtures of water and the ionic liquid 1-butyl-3-methylimidazolium iodide ([BMIM][I]) through a combined experimental and molecular dynamics study. The density, melting point, viscosity, and conductivity of these mixtures were measured by experiment. The composition region below 50% water by mole was found to differ dramatically from the region above 50% water, with trends in density and melting point differing before and after that point. Water was found to have a profound effect on viscosity and conductivity of the IL, and the effect of hydrogen bonding was discussed. Molecular dynamics simulations representing the same mixture compositions were performed. Molecular ordering was observed, as were changes in this ordering corresponding to water content. Molecular ordering was related to the experimentally measured mixture properties, providing a possible explanation for the two distinct composition regions identified by experiment. PMID:26090562

  7. Nonaborane and decaborane cluster anions can enhance the ignition delay in hypergolic ionic liquids and induce hypergolicity in molecular solvents.

    PubMed

    McCrary, Parker D; Barber, Patrick S; Kelley, Steven P; Rogers, Robin D

    2014-05-01

    The dissolution of nido-decaborane, B10H14, in ionic liquids that are hypergolic (fuels that spontaneously ignite upon contact with an appropriate oxidizer), 1-butyl-3-methylimidazolium dicyanamide, 1-methyl-4-amino-1,2,4-triazolium dicyanamide, and 1-allyl-3-methylimidazolium dicyanamide, led to the in situ generation of a nonaborane cluster anion, [B9H14](-), and reductions in ignition delays for the ionic liquids suggesting salts of borane anions could enhance hypergolic properties of ionic liquids. To explore these results, four salts based on [B10H13](-) and [B9H14](-), triethylammonium nido-decaborane, tetraethylammonium nido-decaborane, 1-ethyl-3-methylimidazolium arachno-nonaborane, and N-butyl-N-methyl-pyrrolidinium arachano-nonaborane were synthesized from nido-decaborane by reaction of triethylamine or tetraethylammonium hydroxide with nido-decaborane in the case of salts containing the decaborane anion or via metathesis reactions between sodium nonaborane (Na[B9H14]) and the corresponding organic chloride in the case of the salts containing the nonaborane anion. These borane cluster anion salts form stable solutions in some combustible polar aprotic solvents such as tetrahydrofuran and ethyl acetate and trigger hypergolic reactivity of these solutions. Solutions of these salts in polar protic solvents are not hypergolic. PMID:24716643

  8. Comparison of different ionic liquids pretreatment for corn stover enzymatic saccharification.

    PubMed

    Mood, Sohrab Haghighi; Golfeshan, Amir Hossein; Tabatabaei, Meisam; Abbasalizadeh, Saeed; Ardjmand, Mehdi; Jouzani, Gholamreza Salehi

    2014-01-01

    Recently, application of ionic liquids (ILs) has received much attention due to their special solvency properties as a promising method of pretreatment for lignocellulosic biomass. Easy recovery of ionic liquids, chemical stability, temperature stability, nonflammability, low vapor pressure, and wide liquidus range are among those unique properties. These solvents are also known as green solvents due to their low vapor pressure. The present study was set to compare the effect of five different ILs, namely, 1-ethyl-3-methylimidazolium acetate ([EMIM][Ac]), 1-butyl-3-methylimidazolium chloride ([BMIM][Cl]), 1-ethyl-3-methyl imidazolium diethyl phosphate ([EMIM][DEP]), 1-allyl-3-methylimidazolium chloride ([AMIM][Cl]), and 1-ethyl-3-methylimidazolium-hydrogen sulfate ([EMIM][HSO₄]), on corn stover in a bioethanol production process. The performance of ILs was evaluated based on the change observed in chemical structure, crystallinity index, cellulose digestibility, and glucose release. Overall, [EMIM][Ac]-pretreated corn stover led to significantly higher saccharification, with cellulose digestibility reaching 69% after 72 hr, whereas digestibility of untreated barley straw was measured at only 21%. PMID:24397717

  9. Three dimensional ink-jet printing of biomaterials using ionic liquids and co-solvents.

    PubMed

    Gunasekera, Deshani H A T; Kuek, SzeLee; Hasanaj, Denis; He, Yinfeng; Tuck, Christopher; Croft, Anna K; Wildman, Ricky D

    2016-08-15

    1-Ethyl-3-methylimidazolium acetate ([C2C1Im][OAc]) and 1-butyl-3-methylimidazolium acetate ([C4C1Im][OAc]) have been used as solvents for the dissolution and ink-jet printing of cellulose from 1.0 to 4.8 wt%, mixed with the co-solvents 1-butanol and DMSO. 1-Butanol and DMSO were used as rheological modifiers to ensure consistent printing, with DMSO in the range of 41-47 wt% producing samples within the printable range of a DIMATIX print-head used (printability parameter < 10) at 55 °C, whilst maintaining cellulose solubility. Regeneration of cellulose from printed samples using water was demonstrated, with the resulting structural changes to the cellulose sample assessed by scanning electron microscopy (SEM) and white light interferometry (WLI). These results indicate the potential of biorenewable materials to be used in the 3D additive manufacture process to generate single-component and composite materials. PMID:27231729

  10. Carbene formation upon reactive dissolution of metal oxides in imidazolium ionic liquids.

    PubMed

    Wellens, Sil; Brooks, Neil R; Thijs, Ben; Meervelt, Luc Van; Binnemans, Koen

    2014-03-01

    Metal oxides were found to dissolve in different imidazolium ionic liquids with a hydrogen atom in the C2 position of the imidazolium ring, but not if a methyl substituent was present in the C2 position. The crystal structure of the product that crystallised from an ionic liquid containing dissolved silver(i) oxide showed that this was a silver(i) carbene complex. The presence of carbenes in solution was proven by (13)C NMR spectroscopy and the reactions were also monitored by Raman spectroscopy. The dissolution of other metal oxides, namely copper(ii) oxide, zinc(ii) oxide and nickel(ii) oxide, was also studied in imidazolium ionic liquids and it was found that stable zinc(ii) carbenes were formed in solution, but these did not crystallise under the given experimental conditions. A crystalline nickel(ii) carbene complex could be obtained from a solution of nickel(ii) chloride dissolved in a mixture of 1-butyl-3-methylimidazolium and 1-ethyl-3-methylimidazolium acetate. PMID:24390601

  11. Topochemical pretreatment of wood biomass to enhance enzymatic hydrolysis of polysaccharides to sugars.

    PubMed

    Mou, Hong-Yan; Orblin, Elina; Kruus, Kristiina; Fardim, Pedro

    2013-08-01

    The surface chemistry of milled birch and pine wood pretreated by ionic liquid, hydrothermal and hydrotropic methods, followed by enzymatic hydrolysis was studied in this work. Surface coverage by lignin was measured by X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry (ToF-SIMS) was used to describe the surface chemical composition after pretreatment in detail, and the morphology after pretreatment was investigated by FE-SEM. Ionic liquid (1-ethyl-3-methylimidazolium acetate, 1-butyl-3-methylimidazolium chloride) pretreatment at room temperature made the samples swell but did not dissolve the wood. Comparing the surface coverage by lignin, both in the case of birch and pine wood, hydrotropic worked best to remove the lignin hampering enzymatic hydrolysis. ToF-SIMS supported this finding, and showed that in birch, the carbohydrates were degraded more than in pine after hydrotropic pretreatment. The glucose yield of birch was improved by hydrotropic pretreatment from 5.1% to 83.9%, more significantly than in case of pine. PMID:23774220

  12. SEM Observation of Hydrous Superabsorbent Polymer Pretreated with Room-Temperature Ionic Liquids

    PubMed Central

    Tsuda, Tetsuya; Mochizuki, Eiko; Kishida, Shoko; Iwasaki, Kazuki; Tsunashima, Katsuhiko; Kuwabata, Susumu

    2014-01-01

    Room-temperature ionic liquid (RTIL), which is a liquid salt at or below room temperature, shows peculiar physicochemical properties such as negligible vapor pressure and relatively-high ionic conductivity. In this investigation, we used six types of RTILs as a liquid material in the pretreatment process for scanning electron microscope (SEM) observation of hydrous superabsorbent polymer (SAP) particles. Very clear SEM images of the hydrous SAP particles were obtained if the neat RTILs were used for the pretreatment process. Of them, tri-n-butylmethylphosphonium dimethylphosphate ([P4, 4, 4, 1][DMP]) provided the best result. On the other hand, the surface morphology of the hydrous SAP particles pretreated with 1-ethyl-3-methylimidazolium tetrafluoroborate ([C2mim][BF4]) and 1-butyl-3-methylimidazolium tetrafluoroborate ([C4mim][BF4]) was damaged. The results of SEM observation and thermogravimetry analysis of the hydrous SAP pretreated with the RTILs strongly suggested that most water in the SAP particles are replaced with RTIL during the pretreatment process. PMID:24621609

  13. Combined effects of raw materials and solvent systems on the preparation and properties of regenerated cellulose fibers.

    PubMed

    Chen, Jinghuan; Guan, Ying; Wang, Kun; Zhang, Xueming; Xu, Feng; Sun, Runcang

    2015-09-01

    To investigate the combined effects of materials and solvents on the preparation, structural and mechanical properties of regenerated cellulose fibers, four cellulosic materials (microcrystalline cellulose, cotton linter pulp, bamboo pulp and bleached softwood sulfite dissolving pulp) and six non-derivative solvents (NaOH/urea aqueous solution, N,N-dimethylacetamide/lithium chloride, N-methyl-morpholine-N-oxide, 1-butyl-3-methylimidazolium chloride, 1-allyl-3-methylimidazolium chloride and 1-ethyl-3-methylimidazolium acetate) were used to prepare fibers with wet spinning method. The results showed that the dissolvability of solvent was the determining factor in cellulose dissolution, and the dissolving time was influenced by the raw materials' properties, such as molecular weight, exposed area and hemicellulose content. The crystallinity and elongation at break of the fibers were almost fixed and not affected by the materials and solvents. However, the tensile strength of the fibers was directly proportional to the molecular weight of the raw materials, and varied with the type of solvents through cellulose degradation. PMID:26005150

  14. Catalysis of Rice Straw Hydrolysis by the Combination of Immobilized Cellulase from Aspergillus niger on β-Cyclodextrin-Fe3O4 Nanoparticles and Ionic Liquid

    PubMed Central

    Huang, Po-Jung; Chang, Ken-Lin; Chen, Shui-Tein

    2015-01-01

    Cellulase from Aspergillus niger was immobilized onto β-cyclodextrin-conjugated magnetic particles by silanization and reductive amidation. The immobilized cellulase gained supermagnetism due to the magnetic nanoparticles. Ninety percent of cellulase was immobilized, but the activity of immobilized cellulase decreased by 10%. In this study, ionic liquid (1-butyl-3-methylimidazolium chloride) was introduced into the hydrolytic process because the original reaction was a solid-solid reaction. The activity of immobilized cellulase was improved from 54.87 to 59.11 U g immobilized cellulase−1 at an ionic liquid concentration of 200 mM. Using immobilized cellulase and ionic liquid in the hydrolysis of rice straw, the initial reaction rate was increased from 1.629 to 2.739 g h−1 L−1. One of the advantages of immobilized cellulase is high reusability—it was usable for a total of 16 times in this study. Compared with free cellulase, magnetized cellulase can be recycled by magnetic field and the activity of immobilized cellulase was shown to remain at 85% of free cellulase without denaturation under a high concentration of glucose (15 g L−1). Therefore, immobilized cellulase can hydrolyze rice straw continuously compared with free cellulase. The amount of harvested glucose can be up to twentyfold higher than that from the hydrolysis by free cellulase. PMID:25874210

  15. Dissolving process of a cellulose bunch in ionic liquids: a molecular dynamics study.

    PubMed

    Li, Yao; Liu, Xiaomin; Zhang, Suojiang; Yao, Yingying; Yao, Xiaoqian; Xu, Junli; Lu, Xingmei

    2015-07-21

    In recent years, a variety of ionic liquids (ILs) were found to be capable of dissolving cellulose and mechanistic studies were also reported. However, there is still a lack of detailed information at the molecular level. Here, long time molecular dynamics simulations of cellulose bunch in 1-ethyl-3-methylimidazolium acetate (EmimAc), 1-ethyl-3-methylimidazolium chloride (EmimCl), 1-butyl-3-methylimidazolium chloride (BmimCl) and water were performed to analyze the inherent interaction and dissolving mechanism. Complete dissolution of the cellulose bunch was observed in EmimAc, while little change took place in EmimCl and BmimCl, and nothing significant happened in water. The deconstruction of the hydrogen bond (H-bond) network in cellulose was found and analyzed quantitatively. The synergistic effect of cations and anions was revealed by analyzing the whole dissolving process. Initially, cations bind to the side face of the cellulose bunch and anions insert into the cellulose strands to form H-bonds with hydroxyl groups. Then cations start to intercalate into cellulose chains due to their strong electrostatic interaction with the entered anions. The H-bonds formed by Cl(-) cannot effectively separate the cellulose chain and that is the reason why EmimCl and BmimCl dissolve cellulose more slowly. These findings deepen people's understanding on how ILs dissolve cellulose and would be helpful for designing new efficient ILs to dissolve cellulose. PMID:26095890

  16. Phase-transfer behavior of cross-linked poly(acrylic acid) particles prepared by dispersion polymerization from ionic liquid to water.

    PubMed

    Minami, Hideto; Mizuta, Yusuke; Kimura, Akira

    2012-02-01

    The phase-transfer behavior of poly(acrylic acid) (PAA) particles from the hydrophobic ionic liquid N,N-diethyl-N-methyl-N-(2-methoxyethyl)ammonium bis(trifluoromethanesulfonyl)amide phase to the water phase in the particle state, which we reported previously, was examined in more detail. PAA particles were prepared in the ionic liquid 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)amide ([Bmim][TFSA]) and the organic solvent chloroform and were extracted. The transfer of PAA particles to water in the particle state was also observed in [Bmim][TFSA] systems. In contrast, the transfer phenomenon was not observed in the chloroform system. It was clarified that water/oil interfacial tension γ(wo) is an important parameter in the extraction of PAA in the particle state from the viewpoint of free energy. When the cationic surfactant tetradecyltrimethylammonium bromide, aqueous solution was used as the extraction medium, the PAA particles were extracted in the particle state from chloroform to water, in which γ(wo) became as low as that of the ionic liquid. This suggests that the phase-transfer phenomenon of PAA particles in the particle state was induced by the ionic liquid's unique property of low interfacial tension with water despite its high hydrophobic character. PMID:22235893

  17. Multivariable optimization of the micellar system for the ionic liquid-modified MEKC separation of phenolic acids.

    PubMed

    Liu, Lei; Wu, Bin; Liu, Ke; Li, Chao-Ran; Zhou, Xu; Li, Ping; Yang, Hua

    2016-07-15

    An ionic liquid (IL)-modified micellar electrokinetic chromatography (MEKC) method was proposed for the separation and determination of eight phenolic acids. In order to increase separation efficiency and selectivity, the micelle system consisting of aqueous mixtures of ILs, Tween 20 and borate was optimized using a D-optimal design. A 16-run experimental plan was carried out. The results indicated that the addition of ILs in background electrolyte could significantly alter the electrophoretic behavior and improve the resolution of target analytes. By evaluating the electropherograms obtained, a satisfactory separation condition for all analytes was achieved in 10min with optimized buffer composed of 0.70% (w/w) 1-butyl-3-methylimidazolium tetrafluoroborate, 8.1% (w/w) polyoxyethylene sorbitan monolaurate (Tween 20) and 10mM sodium borate at pH 9.2. Under these conditions, all calibration curves showed good linearity (r(2)>0.9969), and accuracy (recoveries ranging from 94.71 to 106.85%). Finally, the proposed method was successfully applied to determine the phenolic acids in a Chinese medicine compound, compound danshen dripping pills. PMID:27136281

  18. Molecular origin of high free energy barriers for alkali metal ion transfer through ionic liquid-graphene electrode interfaces.

    PubMed

    Ivaništšev, Vladislav; Méndez-Morales, Trinidad; Lynden-Bell, Ruth M; Cabeza, Oscar; Gallego, Luis J; Varela, Luis M; Fedorov, Maxim V

    2016-01-14

    In this work we study mechanisms of solvent-mediated ion interactions with charged surfaces in ionic liquids by molecular dynamics simulations, in an attempt to reveal the main trends that determine ion-electrode interactions in ionic liquids. We compare the interfacial behaviour of Li(+) and K(+) at a charged graphene sheet in a room temperature ionic liquid, 1-butyl-3-methylimidazolium tetrafluoroborate, and its mixtures with lithium and potassium tetrafluoroborate salts. Our results show that there are dense interfacial solvation structures in these electrolytes that lead to the formation of high free energy barriers for these alkali metal cations between the bulk and direct contact with the negatively charged surface. We show that the stronger solvation of Li(+) in the ionic liquid leads to the formation of significantly higher interfacial free energy barriers for Li(+) than for K(+). The high free energy barriers observed in our simulations can explain the generally high interfacial resistance in electrochemical storage devices that use ionic liquid-based electrolytes. Overcoming these barriers is the rate-limiting step in the interfacial transport of alkali metal ions and, hence, appears to be a major drawback for a generalised application of ionic liquids in electrochemistry. Some plausible strategies for future theoretical and experimental work for tuning them are suggested. PMID:26661060

  19. A sensitive colorimetric method for the determination of nitrite in water supplies, meat and dairy products using ionic liquid-modified methyl red as a colour reagent.

    PubMed

    Zhang, Haijuan; Qi, Shengda; Dong, Yalei; Chen, Xiaojiao; Xu, Yinyin; Ma, Yanhua; Chen, Xingguo

    2014-05-15

    This paper describes a colorimetric approach to determine trace amounts of nitrite in water supplies, meat and dairy products using 1-butyl-3-methylimidazolium-modified methyl red ([BMIM]MR) as a colour reagent. The technique capitalises on the catalytic effect of nitrite on the oxidative degradation of [BMIM]MR by potassium bromate in acidic media. The absorbances were proportional to nitrite concentrations in the range of 8.70×10(-2) to 4.17 μM with a detection limit of 1.64×10(-2) μM. Compared with the method using methyl red as a colour reagent, 60 times improvement of sensitivity was obtained. Activation energy and the apparent rate constant for the catalytic reaction are 61.11 kJ mol(-1) and 1.18×10(4) s(-1), respectively. The proposed method was successfully applied for the analysis of nitrite in Yellow River water, chicken, and milk with recoveries ranging from 96% to 105%. PMID:24423553

  20. The solvation structures of cellulose microfibrils in ionic liquids

    SciTech Connect

    Mostofian, Barmak; Smith, Jeremy C; Cheng, Xiaolin

    2011-01-01

    The use of ionic liquids for non-derivatized cellulose dissolution promises an alternative method for the thermochemical pretreatment of biomass that may be more efficient and environmentally acceptable than more conventional techniques in aqueous solution. Here, we performed equilibrium MD simulations of a cellulose microfibril in the ionic liquid 1-butyl-3-methylimidazolium chloride (BmimCl) and compared the solute structure and the solute-solvent interactions at the interface with those from corresponding simulations in water. The results indicate a higher occurrence of solvent-exposed orientations of cellulose surface hydroxymethyl groups in BmimCl than in water. Moreover, spatial and radial distribution functions indicate that hydrophilic surfaces are a preferred site of interaction between cellulose and the ionic liquid. In particular, hydroxymethyl groups on the hydrophilic fiber surface adopt a different conformation from their counterparts oriented towards the fiber s core. Furthermore, the glucose units with these solvent-oriented hydroxymethyls are surrounded by the heterocyclic organic cation in a preferred parallel orientation, suggesting a direct and distinct interaction scheme between cellulose and BmimCl.

  1. Enhancing the basicity of ionic liquids by tuning the cation-anion interaction strength and via the anion-tethered strategy.

    PubMed

    Xu, Dan; Yang, Qiwei; Su, Baogen; Bao, Zongbi; Ren, Qilong; Xing, Huabin

    2014-01-30

    Ionic liquids (ILs) with relatively strong basicity often show impressive performance in chemical processes, so it is important to enhance the basicity of ILs by molecular design. Here, we proposed two effective ways to enhance the basicity of ILs: by weakening the cation-anion interaction strength and by employing the anion-tethered strategy. Notably, two quantum-chemical parameters, the most negative surface electrostatic potential and the lowest surface average local ionization energy, were adopted as powerful tools to demonstrate the electrostatic and covalent aspects of basicity, respectively, at the microscopic level. It was shown that, for the ILs with the same anion (acetate or trifluoroacetate), the basicity of the ILs could be enhanced when the cation-anion interaction strength was weakened. For the acetate anion-based ILs, the hydrogen-bonding basicity scale (β) increased by 29% when the cation changed from 1-butyl-3-methylimidazolium ([Bmim]) to tetrabutylphosphonium ([P4444]), achieving one of the highest reported β values for ILs. Moreover, it was also demonstrated that, when an amine group was tethered to the anion of the IL, its basicity was stronger than when it was tethered to the cation. These results are highly instructive for designing ILs with strong basicity and for improving the efficiency of IL-based processes, such as CO2 capture, SO2 and acetylene absorption, dissolution of cellulose, extraction of bioactive compounds, and so on. PMID:24387657

  2. Atomic Resolution Insights into the Structural Aggregations and Optical Properties of Neat Imidazolium-Based Ionic Liquids.

    PubMed

    Du, Likai; Geng, Cuihuan; Zhang, Dongju; Lan, Zhenggang; Liu, Chengbu

    2016-07-14

    A fundamental understanding of the structural heterogeneity and optical properties of ionic liquids is crucial for their potential applications in catalysis, optical measurement, and solar cells. Herein, a synergistic approach combining molecular dynamics simulations, excited-state calculations, and statistical analysis was used to explore the explicit correlation between the structural and optical properties of one imidazolium amino acid-based ionic liquid, 1-butyl-3-methylimidazolium glycine. The estimated absorption spectrum successfully rationalizes the unusual and non-negligible absorption band beyond 300 nm for the neat imidazolium-based ionic liquid. The absorption behavior of imidazolium-based ionic liquids is shown to be sensitive to the details of their locally heterogeneous environments. We quantitatively highlight the imidazolium moiety and its various molecular aggregations, rather than the monomeric imidazolium moiety, that are responsible for the absorption characteristics. These results would improve our understanding of the preliminary interplay between structural heterogeneity and optical properties for neat imidazolium-based ionic liquids. PMID:27276660

  3. Polarity, viscosity, and ionic conductivity of liquid mixtures containing [C4C1im][Ntf2] and a molecular component.

    PubMed

    Lopes, J N Canongia; Gomes, Margarida F Costa; Husson, Pascale; Pádua, Agílio A H; Rebelo, Luis Paulo N; Sarraute, Sabine; Tariq, Mohammad

    2011-05-19

    In this study, we have focused on binary mixtures composed of 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)-imide, [C(4)C(1)im][Ntf(2)], and a selection of six molecular components (acetonitrile, dichloromethane, methanol, 1-butanol, t-butanol, and water) varying in polarity, size, and isomerism. Two Kamlet-Taft parameters, the polarizability π* and the hydrogen bond acceptor β coefficient were determined by spectroscopic measurements. In most cases, the solvent power (dipolarity/polarizability) of the ionic liquid is only slightly modified by the presence of the molecular component unless large quantities of this component are present. The viscosity and electrical conductivity of these mixtures were measured as a function of composition and the relationship between these two properties were studied through Walden plot curves. The viscosity of the ionic liquid dramatically decreases with the addition of the molecular component. This decrease is not directly related to the volumetric properties of each mixture or its interactions. The conductivity presents a maximum as a function of the composition and, except for the case of water, the conductivity maxima decrease for more viscous systems. The Walden plots indicate enhanced ionic association as the ionic liquid gets more diluted, a situation that is the inverse of that usually found for conventional electrolyte solutions. PMID:21517046

  4. Ruthenium nanoparticles in ionic liquids: structural and stability effects of polar solutes.

    PubMed

    Salas, Gorka; Podgoršek, Ajda; Campbell, Paul S; Santini, Catherine C; Pádua, Agílio A H; Costa Gomes, Margarida F; Philippot, Karine; Chaudret, Bruno; Turmine, Mireille

    2011-08-14

    Ionic liquids are a stabilizing medium for the in situ synthesis of ruthenium nanoparticles. Herein we show that the addition of molecular polar solutes to the ionic liquid, even in low concentrations, eliminates the role of the ionic liquid 3D structure in controlling the size of ruthenium nanoparticles, and can induce their aggregation. We have performed the synthesis of ruthenium nanoparticles by decomposition of [Ru(COD)(COT)] in 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, [C(1)C(4)Im][NTf(2)], under H(2) in the presence of varying amounts of water or 1-octylamine. For water added during the synthesis of metallic nanoparticles, a decrease of the solubility in the ionic liquid was observed, showed by nanoparticles located at the interface between aqueous and ionic phases. When 1-octylamine is present during the synthesis, stable nanoparticles of a constant size are obtained. When 1-octylamine is added after the synthesis, aggregation of the ruthenium nanoparticles is observed. In order to explain these phenomena, we have explored the molecular interactions between the different species using (13)C-NMR and DOSY (Diffusional Order Spectroscopy) experiments, mixing calorimetry, surface tension measurements and molecular simulations. We conclude that the behaviour of the ruthenium nanoparticles in [C(1)C(4)Im][NTf(2)] in the presence of 1-octylamine depends on the interaction between the ligand and the nanoparticles in terms of the energetics but also of the structural arrangement of the amine at the nanoparticle's surface. PMID:21603700

  5. Surface Adsorption and Micelle Formation of Polyoxyethylene-type Nonionic Surfactants in Mixtures of Water and Hydrophilic Imidazolium-type Ionic Liquid.

    PubMed

    Misono, Takeshi; Okada, Kohei; Sakai, Kenichi; Abe, Masahiko; Sakai, Hideki

    2016-06-01

    The interfacial properties of polyoxyethylene alkyl ether-type nonionic surfactants (CnEm) were studied in a hydrophilic room-temperature ionic liquid, 1-butyl-3-methylimidazolium tetrafluoroborate (bmimBF4), in the presence of water. These properties were assessed using static surface tension, pyrene fluorescence, and dynamic light scattering measurements. The interfacial properties were strongly dependent on the solution composition. Increased water concentration lowered the critical micelle concentration (cmc). The cmc was also affected by the lengths of both the alkyl and polyoxyethylene chains, but a greater impact was observed for the alkyl chain length. These results indicate that micellization occurs as a result of solvophobic interaction between surfactant molecules in the water/bmimBF4 mixed solutions, similar to aqueous surfactant systems. The cloud point phenomenon was observed for CnEm with a relatively low hydrophilic-lipophilic balance (HLB) value, and the relationship between the cloud point and water/bmimBF4 composition exhibited a convex upward curve. Furthermore, the mixing of bmimBF4 with water increased the surfactant solubility for water-rich compositions, suggesting that bmimBF4 acts as a chaotropic salt. PMID:27181249

  6. Catalytic pyrolysis of cellulose in ionic liquid [bmim]OTf.

    PubMed

    Qu, Guangfei; He, Weiwei; Cai, Yingying; Huang, Xi; Ning, Ping

    2016-09-01

    This study discussed the catalytic cracking process of cellulose in ionic liquid 1-butyl-3-methylimidazolium trifluoromethanesulfonate ([bmim]OTF) under 180°C, 240°C and 340°C, found that [bmim]OTF is an effective catalyst which can effectively reduce the pyrolysis temperature(nearly 200°C) of the cellulose. FRIR, XRD and SEM were used to analyze the structure characterization of fiber before and after the cracking; GC-MS was used for liquid phase products analysis; GC was used to analyze gas phase products. The results showed that the cellulose pyrolysis in [bmim]OTf mainly generated CO2, CO and H2, also generated 2-furfuryl alcohol, 2,5-dimethyl-1,5-diallyl-3-alcohol, 1,4-butyrolactone, 5-methyl furfural, 4-hydroxy butyric acid, vinyl propionate, 1-acetoxyl group-2-butanone, furan formate tetrahydrofuran methyl ester liquid product, and thus simulated the evolution mechanism of cellulose pyrolysis products based on the basic model of cellulose monomer. PMID:27185153

  7. Molecular dynamics simulation of polymer electrolytes based on poly(ethylene oxide) and ionic liquids. II. Dynamical properties

    NASA Astrophysics Data System (ADS)

    Costa, Luciano T.; Ribeiro, Mauro C. C.

    2007-10-01

    Dynamical properties of polymer electrolytes based on poly(ethylene oxide) (PEO) and ionic liquids of 1-alkyl-3-methylimidazolium cations were calculated by molecular dynamics simulations with previously proposed models [L. T. Costa and M. C. Ribeiro, J. Chem. Phys. 124, 184902 (2006)]. The effect of changing the ionic liquid concentration, temperature, and the 1-alkyl-chain lengths, [1,3-dimethylimidazolium]PF6 and [1-butyl-3-methylimidazolium]PF6 ([dmim]PF6 and [bmim]PF6), was investigated. Cation diffusion coefficient is higher than those of anion and oxygen atoms of PEO chains. Ionic mobility in PEO /[bmim]PF6 is higher than in PEO /[dmim]PF6, so that the ionic conductivity κ of the former is approximately ten times larger than the latter. The ratio between κ and its estimate from the Nernst-Einstein equation κ /κNE, which is inversely proportional to the strength of ion pairs, is higher in ionic liquid polymer electrolytes than in polymer electrolytes based on inorganic salts with Li+ cations. Calculated time correlation functions corroborate previous evidence from the analysis of equilibrium structure that the ion pairs in ionic liquid polymer electrolytes are relatively weak. Structural relaxation at distinct spatial scales is revealed by the calculation of the intermediate scattering function at different wavevectors. These data are reproduced with stretched exponential functions, so that temperature and wavevector dependences of best fit parameters can be compared with corresponding results for polymer electrolytes containing simpler ions.

  8. Facile synthesis of nitrogen and sulfur codoped carbon from ionic liquid as metal-free catalyst for oxygen reduction reaction.

    PubMed

    She, Yiyi; Lu, Zhouguang; Ni, Meng; Li, Li; Leung, Michael K H

    2015-04-01

    Developing metal-free catalysts for oxygen reduction reaction (ORR) is a great challenge in the development of fuel cells. Nitrogen and sulfur codoped carbon with remarkably high nitrogen content up to 13.00 at % was successfully fabricated by pyrolysis of homogeneous mixture of exfoliated graphitic flakes and ionic liquid 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([Bimi][Tf2N]). The exfoliated graphite flakes served as a structure-directing substance as well as additional carbon source in the fabrication. It was demonstrated that the use of graphite flakes increased the nitrogen doping level, optimized the composition of active nitrogen configurations, and enlarged the specific surface area of the catalysts. Electrochemical characterizations revealed that the N and S codoped carbon fabricated by this method exhibited superior catalytic activities toward ORR under both acidic and alkaline conditions. Particularly in alkaline solution, the current catalyst compared favorably to the conventional 20 wt % Pt/C catalyst via four-electron transfer pathway with better ORR selectivity. The excellent catalytic activity was mainly ascribed to high nitrogen doping content, appropriate constitution of active nitrogen configurations, large specific surface area, and synergistic effect of N and S codoping. PMID:25781628

  9. The Influence of Silica Nanoparticles on Ionic Liquid Behavior: A Clear Difference between Adsorption and Confinement

    PubMed Central

    Wang, Yaxing; Li, Cheng; Guo, Xiaojing; Wu, Guozhong

    2013-01-01

    The phase behaviors of ionic liquids (ILs) confined in nanospace and adsorbed on outer surface of nanoparticles are expected to be different from those of the bulk. Anomalous phase behaviors of room temperature ionic liquid tributylhexadecylphosphonium bromide (P44416Br) confined in ordered mesoporous silica nanoparticles with average pore size 3.7 nm and adsorbed on outer surface of the same silica nanoparticles were reported. It was revealed that the melting points (Tm) of confined and adsorbed ILs depressed significantly in comparison with the bulk one. The Tm depressions for confined and adsorbed ILs are 8 °C and 14 °C, respectively. For comparison with the phase behavior of confined P44416Br, 1-butyl-3-methylimidazolium bromide (BmimBr) was entrapped within silica nanopores, we observed an enhancement of 50 °C in Tm under otherwise similar conditions. The XRD analysis indicates the formation of crystalline-like phase under confinement, in contrast to the amorphous phase in adsorbed IL. It was confirmed that the behavior of IL has clear difference. Moreover, the complex π-π stacking and H-bonding do not exist in the newly proposed phosphonium-based IL in comparison with the widely studied imidazolium-based IL. The opposite change in melting point of P44416Br@SiO2 and BmimBr@SiO2 indicates that the cationic species plays an important role in the variation of melting point. PMID:24145752

  10. Deep Desulfurization of Diesel Fuels with Plasma/Air as Oxidizing Medium, Diperiodatocuprate (III) as Catalyzer and Ionic Liquid as Extraction Solvent

    NASA Astrophysics Data System (ADS)

    Ban, Lili; Liu, Ping; Ma, Cunhua; Dai, Bin

    2013-12-01

    In this paper, the oxidative desulfurization (ODS) system is directly applied to deal with the catalytic oxidation of sulfur compounds of sulfur-containing model oil by dielectric barrier discharge (DBD) plasma in the presence of air plus an extraction step with the oxidation-treated fuel put over ionic liquid [BMIM]FeCl4 (1-butyl-3-methylimidazolium tetrachloroferrate). This new system exhibited an excellent desulfurization effect. The sulfur content of DBT in diesel oil decreased from 200 ppm to 4.92 ppm (S removal rate up to 97.5%) under the following optimal reaction conditions: air flow rate (ν) of 60 mL/min, amplitude of applied voltage (U) on DBD of 16 kV, input frequency (f) of 79 kHz, catalyst amount (ω) of 1.25 wt%, reaction time (t) of 10 min. Moreover, a high desulfurization rate was obtained during oxidation of benzothiophene (BT) or 4,6-DMDBT (4,6-dimethyl-dibenzothiophene) under the aforementioned conditions. The oxidation reactivity of different S compounds was decreased in the order of DBT, 4,6-DMDBT and BT. The remarkable advantage of the novel ODS system is that the desulfurization condition applies in the presence of air at ambient conditions without peroxides, aqueous solvent or biphasic oil-aqueous solution system.

  11. Ionic liquid tunes microemulsion curvature.

    PubMed

    Liu, Liping; Bauduin, Pierre; Zemb, Thomas; Eastoe, Julian; Hao, Jingcheng

    2009-02-17

    Middle-phase microemulsions formed from cationic dioctadecyldimethylammonium chloride (DODMAC), anionic sodium dodecylsulfate (SDS), n-butanol, and n-heptane were studied. An ionic liquid (IL), 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF4]), was employed as the electrolyte in the aqueous media instead of inorganic salts usually used in microemulsion formulation. Studies have been carried out as a function of the concentrations of [bmim][BF4], n-butanol, total surfactant (cDODMAC+SDS), and temperature on the phase behavior and the ultralow interfacial tensions in which the anionic component is present in excess in the catanionic film. Ultralow interfacial tension measurements confirmed the formation of middle-phase microemulsions and the necessary conditions for stabilizing middle-phase microemulsions. Electrical conductivity, small-angle X-ray scattering (SAXS), and small-angle neutron scattering (SANS) experiments were also performed, indicating that the typical heptane domain size has an average radius of 360 A and the ionic liquid induces softening of the charged catanionic film. Most interestingly, the IL concentration (cIL) is shown to act as an effective interfacial curvature-control parameter, representing a new approach to tuning the formulation of microemulsions and emulsions. The results expand the potential uses of ILs but also point to the design of new ILs that may achieve superefficient control over interfacial and self-assembly systems. PMID:19161325

  12. Organic solvents induce the formation of oil-in-ionic liquid microemulsion aggregations.

    PubMed

    Gao, Yanan; Li, Na; Zhang, Shaohua; Zheng, Liqiang; Li, Xinwei; Dong, Bin; Yu, Li

    2009-02-01

    The role of four organic solvents in the formation process of 1-butyl-3-methylimidazolium tetrafluoroborate (bmimBF4) based ionic liquid (IL) microemulsions is investigated. The results showed that the addition of Triton X-100 remarkably decreased the conductivity of bmimBF4. The added organic solvents provided a strong apolar environment for the hydrophobic tails of Triton X-100 and caused the surfactant molecules to aggregate into the interfacial film of oil-in-bmimBF4 (O/IL) microemulsions. As a result, the conductivities of the solutions were initially increased because the insulative Triton X-100 molecules were assembled, which corresponded to increasing the concentration of continuous bmimBF4 solutions. The hydrophobic interaction between the dispersed organic solvents and the hydrophobic tails of Triton X-100 may be the driving force for the formation of O/IL microemulsions. The droplets of O/IL microemulsions were successively swollen by organic solvents, and a bicontinuous IL-containing microemulsion was observed by freeze-fracture transmission electron microscopy for the first time. The current study can help in further understanding the ILs-containing microemulsions and thereby improve microemulsion theory. PMID:19138136

  13. Dielectric analysis of micelles and microemulsions formed in a hydrophilic ionic liquid. I. Interaction and percolation.

    PubMed

    Lian, Yiwei; Zhao, Kongshuang

    2011-10-01

    Dielectric measurements were carried out on binary mixtures of Triton X-100 (TX-100, a nonionic surfactant with a polyoxyethylene chain) and 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF(4)], a hydrophilic ionic liquid), and [bmim][BF(4)]/TX-100/cyclohexane microemulsions in a wide frequency range to study the molecular interaction and percolation in these systems. Striking dielectric relaxations were observed, and the dc conductivity data were obtained from the measured total dielectric loss spectra. The interaction between TX-100 and [bmim][BF(4)] is estimated by analyzing the dc conductivity of TX-100/[bmim][BF(4)] solutions in light of the Bruggeman's effective medium approximation, which indicates that spherical micelles are formed when the TX-100 volume fraction is below 48% and the number of cations associated with every TX-100 molecule is eight. For IL-oil microemulsions, both the dependence of dc conductivity and the permittivity (for fixed frequency) on cyclohexane concentration were used to identify the oil-in-IL, bicontinuous, and IL-in-oil microregions. Both the conduction and dielectric relaxation behavior suggest that a static percolation occurs in this hydrophilic IL microemulsion. PMID:21859133

  14. Development of novel ionic liquid-based microemulsion formulation for dermal delivery of 5-Fluorouracil.

    PubMed

    Goindi, Shishu; Arora, Prabhleen; Kumar, Neeraj; Puri, Ashana

    2014-08-01

    The present study was aimed at synthesizing an imidazole-based ionic liquid 1-butyl-3-methylimidazolium bromide (BMIMBr) and subsequent development of a novel ionic liquid-in-oil (IL/o) microemulsion (ME) system for dermal delivery of a poorly permeating drug 5-fluorouracil (5-FU). A significant enhancement in the solubility of 5-FU was observed in BMIMBr. IL/o MEs of 5-FU were prepared using isopropyl myristate, Tween 80/Span 20, and BMIMBr. Results of ex vivo skin permeation studies through mice skin indicated that the selected IL/o ME exhibited 4-fold enhancement in percent drug permeation as compared to aqueous solution, 2.3-fold as compared to hydrophilic ointment, and 1.6-fold greater permeation than water in oil (w/o) ME. The results of in vivo studies against dimethylbenz(a)anthracene (DMBA)/12-O-tetradecanoylphorbol-13-acetate (TPA)-induced mice skin carcinogenesis demonstrated that the IL/o ME could effectively treat skin cancer in 4 weeks. In addition, the side effects such as erythema and irritation associated with the conventional formulations were not observed. Histopathological studies showed that the use of IL/o ME caused no anatomic and pathological changes in the skin structure of mice. These studies suggest that the use of IL-based ME system can efficiently enhance the solubility and permeability of 5-FU and hence its therapeutic efficacy. PMID:24668136

  15. Analysis of baicalein, baicalin and wogonin in Scutellariae radix and its preparation by microemulsion electrokinetic chromatography with 1-butyl-3-methylimizolium tetrafluoborate ionic liquid as additive.

    PubMed

    Zhang, Huige; Tian, Kan; Tang, Jianghong; Qi, Shengda; Chen, Hongli; Chen, Xingguo; Hu, Zhide

    2006-10-01

    Microemulsion electrokinetic chromatography (MEEKC) using 1-butyl-3-methylimidazolium tetrafluoroborate (BMIM-BF4) ionic liquid (IL) as additive was developed for the analysis of baicalin, wogonin and baicalein in Scutellariae radix and its preparation. After conducting a series of optimizations, baseline separation was obtained for the analytes within 5min under the optimum conditions (sodium dodecyl sulfate (SDS) 0.88% (m/v) ethyl acetate 0.8% (v/v) butan-1-ol 0.2% (v/v) and the buffer composition were 25% acetonitrile (v/v), 7.5 mM BMIM-BF4 and 10 mM NaH2PO4, pH 8.2, applied voltage 17.5 kV and detection at 254 nm), the method has been successfully applied to the determination and quantification of the analytes in the extracts of S. radix (cooked), S. radix (raw) and Qingfeiyihuowan which was the preparation including S. radix. PMID:16952364

  16. Layered structure of room-temperature ionic liquids in microemulsions by multinuclear NMR spectroscopic studies.

    PubMed

    Falcone, R Dario; Baruah, Bharat; Gaidamauskas, Ernestas; Rithner, Christopher D; Correa, N Mariano; Silber, Juana J; Crans, Debbie C; Levinger, Nancy E

    2011-06-01

    Microemulsions form in mixtures of polar, nonpolar, and amphiphilic molecules. Typical microemulsions employ water as the polar phase. However, microemulsions can form with a polar phase other than water, which hold promise to diversify the range of properties, and hence utility, of microemulsions. Here microemulsions formed by using a room-temperature ionic liquid (RTIL) as the polar phase were created and characterized by using multinuclear NMR spectroscopy. (1)H, (11)B, and (19)F NMR spectroscopy was applied to explore differences between microemulsions formed by using 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF(4)]) as the polar phase with a cationic surfactant, benzylhexadecyldimethylammonium chloride (BHDC), and a nonionic surfactant, Triton X-100 (TX-100). NMR spectroscopy showed distinct differences in the behavior of the RTIL as the charge of the surfactant head group varies in the different microemulsion environments. Minor changes in the chemical shifts were observed for [bmim](+) and [BF(4)](-) in the presence of TX-100 suggesting that the surfactant and the ionic liquid are separated in the microemulsion. The large changes in spectroscopic parameters observed are consistent with microstructure formation with layering of [bmim](+) and [BF(4)](-) and migration of Cl(-) within the BHDC microemulsions. Comparisons with NMR results for related ionic compounds in organic and aqueous environments as well as literature studies assisted the development of a simple organizational model for these microstructures. PMID:21547960

  17. Studies on the micropolarities of bmimBF4/TX-100/toluene ionic liquid microemulsions and their behaviors characterized by UV-visible spectroscopy.

    PubMed

    Li, Na; Gao, Yan'an; Zheng, Liqiang; Zhang, Jin; Yu, Li; Li, Xinwei

    2007-01-30

    Ionic liquids (ILs), 1-butyl-3-methylimidazolium tetrafluoroborate (bmimBF4), were substituted for polar water and formed nonaqueous microemulsions with toluene by the aid of nonionic surfactant TX-100. The phase behavior of the ternary system was investigated, and microregions of bmimBF4-in-toluene (IL/O), bicontinuous, and toluene-in-bmimBF4 (O/IL) were identified by traditional electrical conductivity measurements. Dynamic light scattering (DLS) revealed the formation of the IL microemulsions. The micropolarities of the IL/O microemulsions were investigated by the UV-vis spectroscopy using the methyl orange (MO) and methylene blue (MB) as absorption probes. The results indicated that the polarity of the IL/O microemulsion increased only before the IL pools were formed, whereas a relatively fixed polar microenvironment was obtained in the IL pools of the microemulsions. Moreover, UV-vis spectroscopy has also shown that ionic salt compounds such as Ni(NO3)2, CoCl2, CuCl2, and biochemical reagent riboflavin could be solubilized into the IL/O microemulsion droplets, indicating that the IL/O microemulsions have potential application in the production of metallic or semiconductor nanomaterials, and in biological extractions or as solvents for enzymatic reactions. The IL/O microemulsions may have some expected effects due to the unique features of ILs and microemulsions. PMID:17241018

  18. Nanodroplet cluster formation in ionic liquid microemulsions.

    PubMed

    Gao, Yanan; Voigt, Andreas; Hilfert, Liane; Sundmacher, Kai

    2008-08-01

    A common ionic liquid (IL), 1-butyl-3-methylimidazolium tetrafluoroborate (bmimBF(4)), is used as polar solvent to induce the formation of a reverse bmimBF(4)-in-toluene IL microemulsion with the aid of the nonionic surfactant Triton X-100. The swelling process of the microemulsion droplets by increasing bmimBF(4) content is detected by dynamic light scattering (DLS), conductivity, UV/Vis spectroscopy, and freeze-fracture transmission electron microscopy (FF-TEM). The results show that the microemulsion droplets initially formed are enlarged by the addition of bmimBF(4). However, successive addition of bmimBF(4) lead to the appearance of large-sized microemulsion droplet clusters (200-400 nm). NMR spectroscopic analysis reveal that the special structures and properties of bmimBF(4) and Triton X-100 together with the polar nature of toluene contribute to the formation of such self-assemblies. These unique self-assembled structures of IL-based microemulsion droplet clusters may have some unusual and unique properties with a number of interesting possibilities for potential applications. PMID:18576451

  19. Temperature-induced microstructural changes in ionic liquid-based microemulsions.

    PubMed

    Gao, Yanan; Li, Na; Hilfert, Liane; Zhang, Shaohua; Zheng, Liqiang; Yu, Li

    2009-02-01

    In the present contribution, results concerning the effect of temperature on the nonionic surfactant Triton X-100 based 1-butyl-3-methylimidazolium tetrafluoroborate (bmimBF4)-in-cyclohexane and bmimBF4-in-toluene ionic liquid (IL) reverse microemulsions are reported. Dynamic light scattering (DLS) along with freeze-fracture transmission electron microscopy (FF-TEM) measurements revealed that the sizes of single microemulsion droplets increased with increasing temperature. However, a decreased temperature led to the appearance of droplet clusters, which have also been observed previously when the single microemulsion droplets were swollen by added bmimBF4 to a certain extent (Gao, Y. A.; Vogit, A.; Hilfert, L.; Sundmacher, K. ChemPhysChem, 2008, 9, 1603-1609). Compared to traditional aqueous microemulsions, IL microemulsions revealed relatively high temperature-independence. The droplet-shaped microstructure was always kept in a large range of temperature. The temperature-independence is ascribed to the temperature-insensitive electrostatic attraction between the solubilized bmimBF4 and Triton X-100, which was considered to be the driving force for solubilizing bmimBF4 into the cores of Triton X-100 aggregates. Two-dimensional rotating frame nuclear Overhauser effect (NOE) experiments (ROESY) further confirmed the microstructural change with temperature. PMID:19132875

  20. Surface study of metal-containing ionic liquids by means of photoemission and absorption spectroscopies

    NASA Astrophysics Data System (ADS)

    Caporali, Stefano; Pedio, Maddalena; Chiappe, Cinzia; Pomelli, Christian S.; Acres, Robert G.; Bardi, Ugo

    2016-06-01

    The vacuum/liquid interface of different ionic liquids obtained by dissolving bistriflimide salts of Ag, Al, Cu, Ni, and Zn in 1-butyl-3-methylimidazolium bistriflimide ([bmim][Tf2N]) was investigated under vacuum using AR-XPS and NEXAFS. The XPS spectra show chemical shifts of the nitrogen of the bistriflimide anion as a function of the metal type, indicating different strength of the coordination bonds. In silver bearing ILs, silver ions were found to be only weakly coordinated. On the contrary, Ni, Cu, Zn, and especially Al exhibit large chemical shifts attributable to strong interaction with the bistriflimide ions. The outermost surface was enriched with or depleted of metal ions as a function of the nature of the metals. Nickel and zinc tend to slightly concentrate at the surface while copper, silver, and especially aluminum are depleted at the surface. We also observed that the aliphatic alkyl chains of the cations tend to protrude outside the surface in all systems studied. However, the presence of metals generally increases the amount of bistriflimide at the vacuum/liquid interface.

  1. Synthesis, COSMO-RS analysis and optical properties of surface modified ZnS quantum dots using ionic liquids

    NASA Astrophysics Data System (ADS)

    Shahid, Robina; Muhammad, Nawshad; Gonfa, Girma; Toprak, Muhammet S.; Muhammed, Mamoun

    2015-10-01

    Zinc sulfide (ZnS) quantum dots (QDs) were synthesized using the microwave assisted ionic liquid (MAIL) route. Three ionic liquids (ILs), namely, 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM]BF4]), trihexyl(tetradecyl) phosphonium bis(trifluoromethanesulfonyl) amide ([P6,6,6,14][TSFA]) and trihexyl(tetradecyl) phosphonium chloride ([P6,6,6,14][Cl]) were used in this study. The size and structure of the QDs were characterized by high-resolution transmission electron microscopy (HR-TEM) and selected area electron diffraction (SAED) pattern, respectively. The synthesized QDs were of wurtzite crystalline structure with size less than 5 nm. The QDs were more uniformly distributed while using the phosponium based ILs as a reaction medium during synthesis. The optical properties were investigated by UV-vis absorption and photoluminescence (PL) emission spectroscopy. The optical properties of QDs showed the quantum confinement effect in their absorption and the effect of cation and anion structural moiety was observed on their bandedge emission. The QDs emission intensity was measured higher for [P6,6,6,14][Cl] due to their better dispersion as well as high charge density of Cl anion. The capability of the ILs in stabilizing the QDs was interpreted by density functional theory (DFT) computations. The obtained results are in good agreement with the theoretical prediction.

  2. Investigation of the local structure of mixtures of an ionic liquid with polar molecular species through molecular dynamics: cluster formation and angular distributions.

    PubMed

    Carrete, Jesús; Méndez-Morales, Trinidad; Cabeza, Óscar; Lynden-Bell, Ruth M; Gallego, Luis J; Varela, Luis M

    2012-05-24

    In this work, we used molecular dynamics simulations to analyze in detail the spatial distributions of the different constituents in mixtures of 1-butyl-3-methylimidazolium tetrafluoroborate with three polar molecular species: water and two alcohols of different chain lengths (methanol and ethanol). In particular, we report results regarding the influence of the chosen species and its concentration on the formation of ionic and molecular clusters over the whole miscibility range, as well as on the angular distribution of polar molecules around the anion and the cation in these systems. Both analyses showed that addition of a molecular species breaks down the polar network of the pure ionic liquid in clusters whose mean size decreases progressively as more molecules are added. At very high concentrations of the molecular species, the ions are found to be isolated in mixtures with water and methanol, but they tend to form pairs in ethanol. In mixtures with water we identified large clusters that form a water network at very high water concentrations, while at low water concentrations polar molecules tend to form smaller aggregates. In contrast, in mixtures with alkanols there is no evidence of the formation of large alcohol clusters at any concentration. Spatial order in alcohol was also studied by means of the Kirkwood G factor, reaching the conclusion that the angular correlations which appear in pure alcohols due to dipole interactions are destroyed by the ionic liquid, even when present only in tiny amounts. PMID:22587330

  3. Pretreatment of corn stover by combining ionic liquid dissolution with alkali extraction.

    PubMed

    Geng, Xinglian; Henderson, Wesley A

    2012-01-01

    Pretreatment plays an important role in the efficient enzymatic hydrolysis of biomass into fermentable sugars for biofuels. A highly effective pretreatment method is reported for corn stover which combines mild alkali-extraction followed by ionic liquid (IL) dissolution of the polysaccharides and regeneration (recovery of the polysaccharides as solids). Air-dried, knife-milled corn stover was soaked in 1% NaOH at a moderate condition (90°C, 1 h) and then thoroughly washed with hot deionized (DI) water. The alkali extraction solublized 75% of the lignin and 37% of the hemicellulose. The corn stover fibers became softer and smoother after the alkali extraction. Unextracted and extracted corn stover samples were separately dissolved in an IL, 1-butyl-3-methylimidazolium chloride (C(4) mimCl), at 130°C for 2 h and then regenerated with DI water. The IL dissolution process did not significantly change the chemical composition of the materials, but did alter their structural features. Untreated and treated corn stover samples were hydrolyzed with commercial enzyme preparations including cellulases and hemicellulases at 50°C. The glucose yield from the corn stover sample that was both alkali-extracted and IL-dissolved was 96% in 5 h of hydrolysis. This is a highly effective methodology for minimizing the enzymatic loading for biomass hydrolysis and/or maximizing the conversion of biomass polysaccharides into sugars. PMID:21809330

  4. A roadmap to uranium ionic liquids: anti-crystal engineering.

    PubMed

    Yaprak, Damla; Spielberg, Eike T; Bäcker, Tobias; Richter, Mark; Mallick, Bert; Klein, Axel; Mudring, Anja-Verena

    2014-05-19

    In the search for uranium-based ionic liquids, tris(N,N-dialkyldithiocarbamato)uranylates have been synthesized as salts of the 1-butyl-3-methylimidazolium (C4mim) cation. As dithiocarbamate ligands binding to the UO2(2+) unit, tetra-, penta-, hexa-, and heptamethylenedithiocarbamates, N,N-diethyldithiocarbamate, N-methyl-N-propyldithiocarbamate, N-ethyl-N-propyldithiocarbamate, and N-methyl-N-butyldithiocarbamate have been explored. X-ray single-crystal diffraction allowed unambiguous structural characterization of all compounds except N-methyl-N-butyldithiocarbamate, which is obtained as a glassy material only. In addition, powder X-ray diffraction as well as vibrational and UV/Vis spectroscopy, supported by computational methods, were used to characterize the products. Differential scanning calorimetry was employed to investigate the phase-transition behavior depending on the N,N-dialkyldithiocarbamato ligand with the aim to establish structure-property relationships regarding the ionic liquid formation capability. Compounds with the least symmetric N,N-dialkyldithiocarbamato ligand and hence the least symmetric anions, tris(N-methyl-N-propyldithiocarbamato)uranylate, tris(N-ethyl-N-propyldithiocarbamato)uranylate, and tris(N-methyl-N-butyldithiocarbamato)uranylate, lead to the formation of (room-temperature) ionic liquids, which confirms that low-symmetry ions are indeed suitable to suppress crystallization. These materials combine low melting points, stable complex formation, and hydrophobicity and are therefore excellent candidates for nuclear fuel purification and recovery. PMID:24737451

  5. Separation of polysaccharides from rice husk and wheat bran using solvent system consisting of BMIMOAc and DMI.

    PubMed

    Hou, Qidong; Li, Weizun; Ju, Meiting; Liu, Le; Chen, Yu; Yang, Qian; Wang, Jingyu

    2015-11-20

    A solvent system consisting of 1,3-dimethyl-2-imidazolidinone (DMI), and ionic liquid 1-butyl-3-methylimidazolium acetate (BMIMOAc) was used to separate polysaccharides from rice husk and wheat bran. The effects of the DMI/BMIMOAc ratios, temperature, and time on the dissolution of rice husk and wheat bran were investigated, and the influence of anti-solvents on the regeneration of polysaccharides-rich material was evaluated. We found that the solvent system is more powerful to dissolve rice husk and wheat bran than pure BMIMOAc, and that polysaccharides-rich material can be effectively separated from the biomass solution. The polysaccharides content of regenerated material from wheat bran can reach as high as 94.4% when ethanol was used as anti-solvents. Under optimized conditions, the extraction rate of polysaccharides for wheat bran can reach as high as 71.8% at merely 50°C. The recycled solvent system exhibited constant ability to separate polysaccharides from rice husk and wheat bran. PMID:26344309

  6. Effects of Room-Temperature Ionic Liquids on Freshwater Primary Producers

    NASA Astrophysics Data System (ADS)

    Kulacki, K. J.; Bernot, R. J.; Lamberti, G. A.; Lodge, D. M.

    2005-05-01

    Room-temperature ionic liquids (ILs) are non-volatile chemicals, which are presumed to be environmentally friendly because they pose no significant threat to air quality. However, the potential toxic effects of ILs on aquatic environments have not been studied, despite the likelihood of unintentional releases into streams and lakes during industrial applications. We studied the effects of ILs on the growth rates of the freshwater green algae Scenedesmus quadricauda and Chlamydomonas reinhardtii in 96-h bioassays. ILs with increasing alkyl chain lengths (from 1-butyl- to 1-hexyl- to 1-octyl-3-methylimidazolium bromide) were increasingly toxic to S. quadricauda (EC-50 values of 0.28 mg*L-1, 0.04 mg*L-1, and <0.005 mg*L-1 respectively). S. quadricauda growth rates decreased with increasing IL concentration across all treatments. Compared to controls, C. reinhardtii growth rates were higher at 200-800 mg*L-1 1-butyl-3-methylimidazolium bromide (bmimBr) treatments, but declined at 1600 mg*L-1 bmimBr. These results illustrate that different algal taxa can respond quite differently to potential chemical pollutants. Furthermore, by studying the effects of ILs on primary producers in concert with organisms from other trophic levels, we can develop hypotheses about how these effects may be felt throughout aquatic ecosystems.

  7. Determination of arecoline in areca nut based on field amplification in capillary electrophoresis coupled with electrochemiluminescence detection.

    PubMed

    Xiang, Qian; Gao, Ying; Han, Bingyan; Li, Jing; Xu, Yunhong; Yin, Jianyuan

    2013-01-01

    A sensitive capillary electrophoresis-electrochemiluminescence (CE-ECL) assay with an ionic liquid (IL) was developed for the determination of arecoline in areca nut. The IL, 1-butyl-3-methylimidazolium tetrafluoroborate (BMImBF(4) ), was an effective additive improved not only the separation selectivity but also the detection sensitivity of the analyte. BMImBF(4) in the separation electrolyte made the resistance of the separation buffer much lower than that of the sample solution, which resulted in an enhanced field amplified electrokinetic injection CE. ECL intensity of arecoline is about two times higher than that of the analyte with phosphate-IL buffer system. Resolution between arecoline and other unknown compounds in real samples was improved. Under the optimized conditions (ECL detection at 1.2 V, 16 kV separation voltage, 20 mmol/L phosphate with 10 mmol/L BMImBF(4) buffer at pH 7.50, 5 mmol/L Ru(bpy)(3)(2+) and 50 mmol/L phosphate buffer in the detection reservoir), a detection limit of 5 × 10(-9) mol/L for arecoline was obtained. Relative standard deviations of the ECL intensity and the migration time were 4.51% and 0.72% for arecoline. This method was successfully applied to determination of the amount of arecoline in areca nut within 450 s. PMID:22298421

  8. The Overriding Roles of Concentration and Hydrophobic Effect on Structure and Stability of Heme Protein Induced by Imidazolium-Based Ionic Liquids.

    PubMed

    Jha, Indrani; Kumar, Awanish; Venkatesu, Pannuru

    2015-07-01

    Spectroscopic and molecular docking investigations were carried out to characterize the effect of imidazolium-based ionic liquids (ILs) with varying chain length of the cation on the thermal stability as well as spectroscopic behavior of heme protein hemoglobin (Hb). The goal of this work is to investigate the role of concentration of ILs, the effect of alkyl chain length of the cation, and the related Hofmeister series on the structure of Hb. To achieve this goal, a series of ILs possessing same Cl(-) anion and a set of cation [Cnmim](+) with increasing chain length such as 1-ethyl-3-methylimidazolium chloride ([Emim][Cl]), 1-butyl-3-methylimidazolium chloride ([Bmim][Cl]), 1-hexyl-3-methylimidazolium chloride ([Hmim][Cl]), and 1-decyl-3-methylimidazolium chloride ([Dmim][Cl]) were used in this study. It was observed that the stability of the protein was concentration dependent as well as the hydrophobic interactions between [Cnmim](+) of ILs, and the amino acid residues in the protein played a major role in protein unfolding. As a consequence, the destabilization tendency of the ILs toward the Hb increases with increasing chain length of the cation of ILs. Additionally, the cations of the ILs obeyed the Hofmeister series when arranged in the order of providing stability to Hb structure. PMID:26069954

  9. Optimization of Micellar Electrokinetic Chromatography Method for the Simultaneous Determination of Seven Hydrophilic and Four Lipophilic Bioactive Components in Three Salvia Species.

    PubMed

    Cao, Jiliang; Hu, Ji; Wei, Jinchao; Li, Baocai; Zhang, Mi; Xiang, Cheng; Li, Peng

    2015-01-01

    A micellar electrokinetic chromatography (MEKC) method was developed for the simultaneous determination of seven hydrophilic phenolic acids and four lipophilic tanshinones in three Salvia species. In normal MEKC mode using SDS as surfactant, the investigated 11 compounds could not be well separated. Therefore, several buffer modifiers including β-cyclodextrins (β-CD), ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim]BF4) and organic solvents have been added to the buffer solution to improve the separation selectivity. Under the optimized conditions (BGE, 15 mM sodium tetraborate with 10 mM SDS, 5 mM β-CD, 10 mM [bmim]BF4 and 15% ACN (v/v) as additives; buffer pH, 9.8; voltage, 20 kV; temperature, 25 °C), the 11 investigated analytes could achieve baseline separation in 34 min. The proposed MEKC was additionally validated by evaluating the linearity (R(2) ≥ 0.9965), LODs (0.27-1.39 μg·mL(-1)), and recovery (94.26%-105.17%), demonstrating this method was reproducible, accurate and reliable. Moreover, the contents of the 11 compounds in three Salvia species, including S. miltiorrhiza, S. przewalskii and S. castanea were analyzed. The result showed that the established MEKC method was simple and practical for the simultaneous determination of the hydrophilic and lipophilic bioactive components in Salvia species, which could be used to effectively evaluate the quality of these valued medicinal plants. PMID:26307960

  10. Facile fabrication of a novel anisotropic gold nanoparticle-chitosan-ionic liquid/graphene modified electrode for the determination of theophylline and caffeine.

    PubMed

    Yang, Guangming; Zhao, Faqiong; Zeng, Baizhao

    2014-09-01

    In the present study, a suspension solution containing anisotropic gold nanoparticle (GNP), chitosan (CHIT) and ionic liquid (IL, i.e. 1-butyl-3-methylimidazolium tetrafluoroborate, [BMIM][BF4]), is prepared by reducing HAuCl4 with sodium citrate in CHIT-IL aqueous solution. The hybrid solution is coated on a graphene (r-GO) modified glassy carbon electrode to construct an electrochemical sensor for the determination of theophylline (TP) and caffeine (CAF). The obtained hybrid film shows rough surface, and anisotropic GNPs are well dispersed on it. The factors concerning this assay strategy are carefully investigated, including the components of the hybrid film, the concentrations of r-GO, HAuCl4 and IL, and the pH of buffer solution. Under the optimized conditions, the linear response ranges are 2.50×10(-8)-2.10×10(-6) mol L(-1) and 2.50×10(-8)-2.49×10(-6) mol L(-1) for TP and CAF, respectively; the detection limits are 1.32×10(-9) mol L(-1) and 4.42×10(-9) mol L(-1), respectively. The electrochemical sensor shows good reproducibility, stability and selectivity, and it has been successfully applied to the determination of TP and CAF in real samples. PMID:24913865

  11. Multi-podant diglycolamides and room temperature ionic liquid impregnated resins: An excellent combination for extraction chromatography of actinides.

    PubMed

    Gujar, R B; Ansari, S A; Verboom, W; Mohapatra, P K

    2016-05-27

    Extraction chromatography resins, prepared by impregnating two multi-podant diglycolamide ligands, viz. diglycolamide-functionalized calix[4]arene (C4DGA) and tripodal diglycolamide (T-DGA) dissolved in the room temperature ionic liquid 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)amide (RTIL: C4mimTf2N) on Chromosorb-W (an inert solid support), gave excellent results for the removal of trivalent actinides from acidic waste solutions. Distribution coefficient measurements on several metal ions showed selective sorption of Am(III) over hexavalent uranyl ions and other fission product elements such as strontium and cesium. The sorbed metal ions could be efficiently desorbed with a complexing solution containing guanidine carbonate and EDTA buffer. The sorption of Am(III) on both resins followed pseudo-second order rate kinetics with rate constants of 1.37×10(-6) and 6.88×10(-7)g/cpmmin for T-DGA and C4DGA resins, respectively. The metal sorption on both resins indicated the Langmuir monolayer chemisorption phenomenon with Eu(III) sorption capacities of 4.83±0.21 and 0.52±0.05mg per g of T-DGA and C4DGA resins, respectively. The results of column studies show that these resins are of interest for a possible application for the recovery of hazardous trivalent actinides from dilute aqueous solutions. PMID:27130582

  12. Desorption of low-volatility compounds induced by dynamic friction between microdroplets and an ultrasonically vibrating blade.

    PubMed

    Usmanov, D T; Hiraoka, K; Wada, H; Morita, S; Nonami, H

    2016-02-21

    Friction plays an important role in desorption and/or ionization of nonvolatile compounds in mass spectrometry, e.g., sonic spray, easy ambient sonic-spray ionization, solvent-assisted inlet ionization, desorption electrospray, etc. In our previous work, desorption of low molecular weight compounds induced by solid/solid dynamic friction was studied. The objective of this work was to investigate desorption of low-volatility compounds induced by liquid/solid friction. Water/methanol (1/1) microdroplets with ∼30 μm in diameter were generated by using a piezoelectric microdroplet generator. They were injected to analytes deposited on the flat surface of a blade vibrating ultrasonically with the frequency of 40 kHz. Neutral molecules desorbed from the blade were ionized by a helium dielectric barrier discharge (DBD), generating strong signals for samples including drugs, explosives, and insecticides. These signals were not detected when either the blade vibrator or the piezoelectric microdroplet generator was off. In contrast, for ionic compounds such as 1-butyl-3-methylimidazolium bis(trifluoro-methylsulfonyl)imide, p-chlorobenzyl pyridinium chloride, and rhodamine B, strong ion signals were obtained when the vibrator and droplet generator were on, but DBD was off. Sub-nanogram limits of detection were attained for low-volatility compounds. PMID:26779570

  13. A roadmap to uranium ionic liquids: Anti-crystal engineering

    DOE PAGESBeta

    Yaprak, Damla; Spielberg, Eike T.; Bäcker, Tobias; Richter, Mark; Mallick, Bert; Klein, Axel; Mudring, Anja -Verena

    2014-04-15

    In the search for uranium-based ionic liquids, tris(N,N-dialkyldithiocarbamato)uranylates have been synthesized as salts of the 1-butyl-3-methylimidazolium (C4mim) cation. As dithiocarbamate ligands binding to the UO22+ unit, tetra-, penta-, hexa-, and heptamethylenedithiocarbamates, N,N-diethyldithiocarbamate, N-methyl-N-propyldithiocarbamate, N-ethyl-N-propyldithiocarbamate, and N-methyl-N-butyldithiocarbamate have been explored. X-ray single-crystal diffraction allowed unambiguous structural characterization of all compounds except N-methyl-N-butyldithiocarbamate, which is obtained as a glassy material only. In addition, powder X-ray diffraction as well as vibrational and UV/Vis spectroscopy, supported by computational methods, were used to characterize the products. Differential scanning calorimetry was employed to investigate the phase-transition behavior depending on the N,N-dialkyldithiocarbamato ligand with the aim tomore » establish structure–property relationships regarding the ionic liquid formation capability. Compounds with the least symmetric N,N-dialkyldithiocarbamato ligand and hence the least symmetric anions, tris(N-methyl-N-propyldithiocarbamato)uranylate, tris(N-ethyl-N-propyldithiocarbamato)uranylate, and tris(N-methyl-N-butyldithiocarbamato)uranylate, lead to the formation of (room-temperature) ionic liquids, which confirms that low-symmetry ions are indeed suitable to suppress crystallization. As a result, these materials combine low melting points, stable complex formation, and hydrophobicity and are therefore excellent candidates for nuclear fuel purification and recovery.« less

  14. Full-ionic liquid gel electrolytes: Enhanced photovoltaic performances in dye-sensitized solar cells

    NASA Astrophysics Data System (ADS)

    Li, Qinghua; Tang, Qunwei; He, Benlin; Yang, Peizhi

    2014-10-01

    Liquid electrolytes containing redox species have been widely used in dye-sensitized solar cells (DSSCs), whereas the volatility of organic solvents has been a tremendous obstacle for their commercial application. To assemble durable DSSCs, here we report the synthesis of full-ionic liquid electrolyte, in which 1-butyl-3-methylimidazolium nitrate is employed as solvent and 1-methyl-3-propylimidazolium iodide is iodide source. Using the imbibition performance of amphiphilic poly(acrylic acid/gelatin) [poly(AA/GR)] and poly(acrylic acid/cetyltrimethyl ammonium bromide) [poly(AA/CTAB)] matrices, full-ionic liquid electrolytes are imbibed into three-dimensional framework of poly(AA/GR) or poly(AA/CTAB) to form stable gel electrolytes. Room-temperature ionic conductivities as high as 17.82 and 18.44 mS cm-1 are recorded from full-ionic liquid imbibed poly(AA/GR) and poly(AA/CTAB) gel electrolytes, respectively. Promising power conversion efficiencies of 7.19% and 7.15% are determined from their DSSC devices in comparison with 6.55% and 6.12% from traditional acetonitrile-based poly(AA/GR) and poly(AA/CTAB) gel electrolytes, respectively. The new concept along with easy fabrication demonstrates the full-ionic liquid electrolytes to be good alternatives for robust gel electrolytes in quasi-solid-state DSSCs.

  15. Ionic liquid biodegradability depends on specific wastewater microbial consortia.

    PubMed

    Docherty, Kathryn M; Aiello, Steven W; Buehler, Barbara K; Jones, Stuart E; Szymczyna, Blair R; Walker, Katherine A

    2015-10-01

    Complete biodegradation of a newly-synthesized chemical in a wastewater treatment plant (WWTP) eliminates the potential for novel environmental pollutants. However, differences within- and between-WWTP microbial communities may alter expectations for biodegradation. WWTP communities can also serve as a source of unique consortia that, when enriched, can metabolize chemicals that tend to resist degradation, but are otherwise promising green alternatives. We tested the biodegradability of three ionic liquids (ILs): 1-octyl-3-methylpyridinium bromide (OMP), 1-butyl-3-methylpyridinium bromide (BMP) and 1-butyl-3-methylimidazolium chloride (BMIM). We performed tests using communities from two WWTPs at three time points. Site-specific and temporal variation both influenced community composition, which impacted the success of OMP biodegradability. Neither BMP nor BMIM degraded in any test, suggesting that these ILs are unlikely to be removed by traditional treatment. Following standard biodegradation assays, we enriched for three consortia that were capable of quickly degrading OMP, BMP and BMIM. Our results indicate WWTPs are not functionally redundant with regard to biodegradation of specific ionic liquids. However, consortia can be enriched to degrade chemicals that fail biodegradability assays. This information can be used to prepare pre-treatment procedures and prevent environmental release of novel pollutants. PMID:25985304

  16. Amyloid formation and disaggregation of {alpha}-synuclein and its tandem repeat ({alpha}-TR)

    SciTech Connect

    Bae, Song Yi; Kim, Seulgi; Hwang, Heejin; Kim, Hyun-Kyung; Yoon, Hyun C.; Kim, Jae Ho; Lee, SangYoon; Kim, T. Doohun

    2010-10-01

    Research highlights: {yields} Formation of the {alpha}-synuclein amyloid fibrils by [BIMbF{sub 3}Im]. {yields} Disaggregation of amyloid fibrils by epigallocatechin gallate (EGCG) and baicalein. {yields} Amyloid formation of {alpha}-synuclein tandem repeat ({alpha}-TR). -- Abstract: The aggregation of {alpha}-synuclein is clearly related to the pathogenesis of Parkinson's disease. Therefore, detailed understanding of the mechanism of fibril formation is highly valuable for the development of clinical treatment and also of the diagnostic tools. Here, we have investigated the interaction of {alpha}-synuclein with ionic liquids by using several biochemical techniques including Thioflavin T assays and transmission electron microscopy (TEM). Our data shows a rapid formation of {alpha}-synuclein amyloid fibrils was stimulated by 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [BIMbF{sub 3}Im], and these fibrils could be disaggregated by polyphenols such as epigallocatechin gallate (EGCG) and baicalein. Furthermore, the effect of [BIMbF{sub 3}Im] on the {alpha}-synuclein tandem repeat ({alpha}-TR) in the aggregation process was studied.

  17. Determination of chlorophenols in red wine using ionic liquid countercurrent chromatography as a new pretreatment method followed by high-performance liquid chromatography.

    PubMed

    Fan, Chen; Li, Nai; Cao, Xueli

    2015-06-01

    A countercurrent chromatography method for the enrichment and cleanup of chlorophenols from food samples was successfully established by using an ionic-liquid-modified two-phase solvent system composed of dichloromethane containing 2% 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide and water. The column was firstly filled with the organic stationary phase, and then a large volume of sample was pumped into the column after it was equilibrated with pure water at the rotation speed. Finally, the trace amounts of chlorophenols extracted and enriched in the stationary phase were eluted out by an alkaline mobile phase and determined by high-performance liquid chromatography. Under optimized conditions, the enrichment and cleanup of the chlorophenols can be fulfilled online with enrichment factors (34-65) and high recoveries (84.69-95.23%). The method has been applied to the determination of chlorophenols in real red wine samples with the limits of detection in the range of 1.89-4.21 μg/L. The present method is highly suitable for the pretreatment of large volume of aqueous sample for the determination of trace amounts of contaminants in food and environmental samples. PMID:25826668

  18. Toxicity of two imidazolium ionic liquids, [bmim][BF4] and [omim][BF4], to standard aquatic test organisms: Role of acetone in the induced toxicity.

    PubMed

    Tsarpali, Vasiliki; Dailianis, Stefanos

    2015-07-01

    The main goal of this study was to investigate the toxicity of the imidazolium-based ionic liquids (ILs), [bmim][BF4] (1-butyl-3-methylimidazolium tetrafluoroborate) and [omim][BF4] (1-octyl-3-methylimidazolium tetrafluoroborate), in battery of standard aquatic toxicity test organisms. Specifically, exposure of the algae Scenedesmus rubescens, crustaceans Thamnocephalus platyurus and Artemia franciscana, rotifers Brachionus calyciflorus and Brachionus plicatilis and bivalve Mytilus galloprovincialis to different concentrations of [bmim][BF4], [omim][BF4] and/or a binary mixture of [bmim][BF4]-[omim][BF4] (1:1) with or without acetone (carrier solvent), revealed that solvent can differentially mediate ILs' toxic profile. Acetone's ability to differentially affect ILs' cation's alkyl chain length, as well as the hydrolysis of [BF4(-)] anions was evident. Given that the toxic potency of the tested ILs seemed to be equal or even higher (in some cases) than those of conventional organic solvents, the present study revealed that the characterization of imidazolium-based ILs as "green solvents" should not be generalized, at least in case of their natural occurrence in mixtures with organic solvents, such as acetone. PMID:25839183

  19. Esterification of potato starch by a biocatalysed reaction in an ionic liquid.

    PubMed

    Zarski, Arkadiusz; Ptak, Sylwia; Siemion, Przemyslaw; Kapusniak, Janusz

    2016-02-10

    In this study, potato starch was esterified with oleic acid, using 1-butyl-3-methylimidazolium chloride as a reaction medium and an immobilised lipase from Thermomyces lanuginosus as a catalyst. The degree of substitution (DS) of the products was determined by the volumetric method; and the best esterified product (with the highest DS) was determined by an elemental analysis. The effect of the reaction parameters on the DS, such as the time and the temperature, were also studied. The product with the highest DS (0.22) was found in the reaction carried out at 60 °C for 4h. Fourier transform infrared (FTIR) and nuclear magnetic resonance (NMR) analyses confirmed the esterification of the potato starch. Furthermore, the results of X-ray diffraction (XRD) and a scanning electron microscopy (SEM) revealed that the crystallinity and the morphology of the native potato starch was slightly changed during its partial gelatinisation in the ionic liquid, and was completely destroyed as a result of the formation of the esters. The thermal stability of the starch oleate decreased, when compared to the unmodified starch, as was indicated by a thermal gravimetric analysis (TGA). PMID:26686176

  20. Novel cellulosic gel preparation for using in electro-responsive applications

    NASA Astrophysics Data System (ADS)

    Kunchornsup, Wissawin; Sirivat, Anuvat

    2010-04-01

    Electroactive-papers (EAPaps) are paper that used in the field of electro-responsive applications, consisting primarily of a cellulose. 1-butyl-3-methylimidazolium chloride (BMIMCl) is an interesting ionic liquid that acts as an effective cellulose solvent for EAPap due to its high solubility without chain derivatization, less chain degradation, and stability in electro-responsive applications. In our work, physical and chemical cellulose gels were fabricated and studied for the effects of varying crosslinking ratio (CR) with glutaraldehyde (GA) as the crosslinking agent. The crosslinking reaction conversion could be increased by increasing the CR; the reaction products are ketone linkages and by-product water molecules. A difference in optical properties could be observed and related to the differing amounts of ketone linkages, as confirmed by Fourier transform infrared spectroscopy: Attenuated total reflectance (FTIR-ATR), and the degradation temperature (Td). All of the prepared gels show no significant differences in electrical conductivity; however they can be classified in the level of semiconductors. Our paper-gels showed potential characteristics towards electro-responsive applications as the ionic migration is a promising mechanism and with less preparation time (< 14 hours).

  1. Theinfluence of a hierarchical porous carbon network on the coherent dynamics of a nanoconfined room temperature ionic liquid: A neutron spin echo and atomistic simulation investigation

    SciTech Connect

    Banuelos, Jose Leo; Feng, Guang; Fulvio, Pasquale F; Li, Song; Rother, Gernot; Arend, Nikolas; Faraone, Antonio; Dai, Sheng; Cummings, Peter T; Wesolowski, David J

    2014-01-01

    The molecular-scale dynamic properties of the room temperature ionic liquid (RTIL) 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, or [C4mim+ ][Tf2N ], confined in hierarchical microporous mesoporous carbon, were investigated using neutron spin echo (NSE) and molecular dynamics (MD) simulations. Both NSE and MD reveal pronounced slowing of the overall collective dynamics, including the presence of an immobilized fraction of RTIL at the pore wall, on the time scales of these approaches. A fraction of the dynamics, corresponding to RTIL inside 0.75 nm micropores located along the mesopore surfaces, are faster than those of RTIL in direct contact with the walls of 5.8 nm and 7.8 nm cylindrical mesopores. This behavior is ascribed to the near-surface confined-ion density fluctuations resulting from the ion ion and ion wall interactions between the micropores and mesopores as well as their confinement geometries. Strong micropore RTIL interactions result in less-coordinated RTIL within the micropores than in the bulk fluid. Increasing temperature from 296 K to 353 K reduces the immobilized RTIL fraction and results in nearly an order of magnitude increase in the RTIL dynamics. The observed interfacial phenomena underscore the importance of tailoring the surface properties of porous carbons to achieve desirable electrolyte dynamic behavior, since this impacts the performance in applications such as electrical energy storage devices.

  2. Effect of unsaturation on the absorption of ethane and ethylene in imidazolium-based ionic liquids.

    PubMed

    Moura, Leila; Mishra, Manas; Bernales, Varinia; Fuentealba, Patricio; Padua, Agilio A H; Santini, Catherine C; Costa Gomes, Margarida F

    2013-06-20

    The influence of the presence of imidazolium side chain unsaturation on the solubility of ethane and ethylene was studied in three ionic liquids: 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)amide-saturated alkyl side-chain in the cation; 1-methyl-3-(buten-3-yl)imidazolium bis(trifluorosulfonyl)imide-double bond in the side-chain of the cation; and 1-methyl-3-benzylimidazolium bis(trifluorosulfonyl)imide-benzyl group in the side-chain of the cation. The solubility of both gases decreases when the side-chain of the cations is functionalized with an unsaturated group. This can be explained by a less favorable enthalpy of solvation. The difference of solubility between ethane and ethylene can be explained from a balance of enthalpic and entropic factors: for the ionic liquid with the saturated alkyl side-chain and the benzyl-substituted side-chain, it is the favorable entropy of solvation that explains the larger ethylene solubility, whereas in the case of the saturated side-chain, it is the more favorable enthalpy of solvation. Molecular simulation allowed the identification of the mechanisms of solvation and the preferential solvation sites for each gas in the different ionic liquids. Simulations have shown that the entropy of solvation is more favorable when the presence of the gas weakens the cation-anion interactions or when the gas can be solvated near different sites of the ionic liquid. PMID:23713882

  3. Mechanisms of metal ion transfer into room-temperature ionic liquids : the role of anion exchange.

    SciTech Connect

    Jensen, M. P.; Neuefeind, J.; Beitz, J. V.; Skanthakumar, S.; Soderholm, L.; Chemistry

    2003-12-17

    The structure and stoichiometry of the lanthanide(III) (Ln) complexes with the ligand 2-thenoyltrifluoroacetone (Htta) formed in a biphasic aqueous room-temperature ionic liquid system have been studied by complementary physicochemical methods. Equilibrium thermodynamics, optical absorption and luminescence spectroscopies, high-energy X-ray scattering, EXAFS, and molecular dynamics simulations all support the formation of anionic Nd(tta){sub 4}{sup -} or Eu(tta){sub 4}{sup -} complexes with no water coordinated to the metal center in 1-butyl-3-methylimidazolium bis[(trifluoromethyl)sulfonyl]imide (C{sub 4}mim{sup +}Tf{sub 2}N{sup -}), rather than the hydrated, neutral complexes, M(tta){sub 3}(H{sub 2}O){sub n} (n = 2 or 3), that form in nonpolar molecular solvents, such as xylene or chloroform. The presence of anionic lanthanide complexes in C{sub 4}mim{sup +}Tf{sub 2}N{sup -} is made possible by the exchange of the ionic liquid anions into the aqueous phase for the lanthanide complex. The resulting complexes in the ionic liquid phase should be thought of as weak C{sub 4}mim{sup +}Ln(tta){sub 4}{sup -} ion pairs which exert little influence on the structure of the ionic liquid phase.

  4. Catalytic hydrolysis of lignocellulosic biomass into 5-hydroxymethylfurfural in ionic liquid.

    PubMed

    Wang, Pan; Yu, Hongbing; Zhan, Sihui; Wang, Shengqiang

    2011-03-01

    Production of 5-hydroxymethylfurfural (HMF) from cellulose catalyzed by solid acids and metal chlorides was studied in the 1-butyl-3-methylimidazolium chloride ([BMIM]Cl) under microwave irradiation. Among the applied catalysts, the use of CrCl(3)/LiCl resulted in the highest yield of HMF. The effects of catalyst dosage (mole ratio of catalyst to glucose units in the feedstock) and reaction temperature on HMF yields were investigated to obtain optimal process conditions. With the 1:1 mol ratio of catalyst to glucose unit, the HMF yield reached 62.3% at 160°C for 10 min. Untreated wheat straw was also investigated as feedstock to produce HMF for the practical use of raw biomass, in which the HMF yield was comparable to that from pure cellulose. After the extraction of HMF, [BMIM]Cl and CrCl(3)/LiCl could be reused and exhibited no activity loss after three successive runs. PMID:21232942

  5. A roadmap to uranium ionic liquids: Anti-crystal engineering

    SciTech Connect

    Yaprak, Damla; Spielberg, Eike T.; Bäcker, Tobias; Richter, Mark; Mallick, Bert; Klein, Axel; Mudring, Anja -Verena

    2014-04-15

    In the search for uranium-based ionic liquids, tris(N,N-dialkyldithiocarbamato)uranylates have been synthesized as salts of the 1-butyl-3-methylimidazolium (C4mim) cation. As dithiocarbamate ligands binding to the UO22+ unit, tetra-, penta-, hexa-, and heptamethylenedithiocarbamates, N,N-diethyldithiocarbamate, N-methyl-N-propyldithiocarbamate, N-ethyl-N-propyldithiocarbamate, and N-methyl-N-butyldithiocarbamate have been explored. X-ray single-crystal diffraction allowed unambiguous structural characterization of all compounds except N-methyl-N-butyldithiocarbamate, which is obtained as a glassy material only. In addition, powder X-ray diffraction as well as vibrational and UV/Vis spectroscopy, supported by computational methods, were used to characterize the products. Differential scanning calorimetry was employed to investigate the phase-transition behavior depending on the N,N-dialkyldithiocarbamato ligand with the aim to establish structure–property relationships regarding the ionic liquid formation capability. Compounds with the least symmetric N,N-dialkyldithiocarbamato ligand and hence the least symmetric anions, tris(N-methyl-N-propyldithiocarbamato)uranylate, tris(N-ethyl-N-propyldithiocarbamato)uranylate, and tris(N-methyl-N-butyldithiocarbamato)uranylate, lead to the formation of (room-temperature) ionic liquids, which confirms that low-symmetry ions are indeed suitable to suppress crystallization. As a result, these materials combine low melting points, stable complex formation, and hydrophobicity and are therefore excellent candidates for nuclear fuel purification and recovery.

  6. Observation of Charge Inversion of an Ionic Liquid at the Solid Salt-Liquid Interface by Sum Frequency Generation Spectroscopy.

    PubMed

    Peñalber, Chariz Y; Baldelli, Steven

    2012-04-01

    Sum frequency generation (SFG) vibrational spectroscopy of the ionic liquid, 1-butyl-3-methylimidazolium dicyanamide [BMIM][DCA], in contact with two different solid salt surfaces, BaF2(111) single crystal and solid NaCl{100}, are discussed in this Letter. This investigation describes the nature of an ionic liquid-(solid) salt interface using SFG, contributing a new understanding to the molecular-level interactions involved in salts, which are conceptually similar compounds (of purely ionic character) but of different physical properties (liquid versus solid at room temperature). Results show the presence of [BMIM](+) at the NaCl{100} surface and [DCA](-) at the BaF2(111) surface. [BMIM](+) cations adhere closely via Coulombic interactions to the negatively charged NaCl{100} surface, while [DCA](-) anions subsequently have a strong electrostatic affinity to the positively charged BaF2(111) surface. Ions of the ionic liquid adsorb to the solid salt surface to form a Helmholtz-like electric double layer. PMID:26286408

  7. Application of ionic liquids for elution of bioactive flavonoid glycosides from lime fruit by miniaturized matrix solid-phase dispersion.

    PubMed

    Xu, Jing-Jing; Yang, Rui; Ye, Li-Hong; Cao, Jun; Cao, Wan; Hu, Shuai-Shuai; Peng, Li-Qing

    2016-08-01

    In this work, two flavonoid glycosides (neohesperidin and naringin) in lime fruit were effectively extracted by miniaturized matrix solid phase dispersion (MSPD), followed by ultra-performance liquid chromatography-ultraviolet detection. The best results were obtained using Florisil (150mg) as the sorbent and 1-butyl-3-methylimidazolium tetrafluoroborate (0.4mL, 250mM) as the elution solvent. This work represents the first attempt of using ionic liquids as a green eluent for extraction of the investigated compounds in miniaturized MSPD. Compared with the conventional methods, the proposed method is advantageous due to improved enrichment factor and reduced reagent consumption. A good linearity was observed with r(2) values (>0.998). Meanwhile, the method gave acceptable recoveries (90.16-96.47%) for the determination of flavonoids in plant samples. The limits of detection of the two analytes ranged between 4.08 and 5.04μg/g. The results showed that the optimized method has a great potential for sample preparation in routine analysis of complex plant samples. PMID:26988490

  8. Solubility and solvation of monosaccharides in ionic liquids.

    PubMed

    Teles, Ana Rita R; Dinis, Teresa B V; Capela, Emanuel V; Santos, Luís M N B F; Pinho, Simão P; Freire, Mara G; Coutinho, João A P

    2016-07-20

    Herein, solubility experimental data for six monosaccharides, viz.d-(+)-glucose, d-(+)-mannose, d-(-)-fructose, d-(+)-galactose, d-(+)-xylose and l-(+)-arabinose, in four ionic liquids (ILs), at temperatures ranging from 288.2 to 348.2 K, were obtained aimed at gathering a better understanding of their solvation ability and molecular-level mechanisms which rule the dissolution process. To ascertain the chemical features that enhance the solubility of monosaccharides, ILs composed of dialkylimidazolium or tetraalkylphosphonium cations combined with the dicyanamide, dimethylphosphate or chloride anions were investigated. It was found that the ranking of the solubility of monosaccharides depends on the IL; yet, d-(+)-xylose is always the most soluble while d-(-)-fructose is the least soluble monosaccharide. The results obtained show that both the IL cation and the anion play a major role in the solubility of monosaccharides. Finally, from the determination of the respective thermodynamic properties of solution, it was found that enthalpic contributions are dominant in the solubilization process. However, the observed differences in the solubilities of monosaccharides in 1-butyl-3-methylimidazolium dicyanamide are ruled by a change in the entropy of solution. PMID:27380720

  9. [(Pb6I8){Mn(CO)5}6](2-): an octahedral (M6X8)-like cluster with inverted bonding.

    PubMed

    Wolf, Silke; Reiter, Kevin; Weigend, Florian; Klopper, Wim; Feldmann, Claus

    2015-04-20

    [BMIm]2[{PbMn(CO)5)}6I8] (BMIm: 1-butyl-3-methylimidazolium) is obtained by ionic liquid mediated reaction of PbI2 and Mn2(CO)10. Central is a cubelike (Pb6I8) unit containing a nonfilled Pb6 octahedron. Each Pb of this (Pb6I8) unit is terminated on its outside by Mn(CO)5, exhibiting Pb-Mn metal-to-metal bonding (280 pm). Structurally, the (Pb6I8) unit is similar to the well-known octahedral (M6Xn) cluster-type family (M = Zr, Nb, Ta, Mo, W; X = Cl, Br, I). In contrast to most similar cluster compounds, such as W6Br12 ([W6Br8]Br2/1Br4/2, according to Niggli notation) or the carbonyl cluster [Sn6{Cr(CO5)6}](2-), however, the nonfilled central Pb6 octahedron in [{PbMn(CO)5)}6I8](2-) does not exhibit any metal-to-metal bonding. Structure and bonding of the title compound are validated by single-crystal structure analysis, energy-dispersive X-ray analysis (EDX), infrared spectroscopy (FT-IR), and density functional theory (DFT) calculations. Based on the isolobal principle, electronegativity considerations, bond lengths, and DFT calculations including Mulliken population analysis and natural population analysis (NPA), in sum, the charge distribution of Pb is best reflected by an oxidation state of +1. PMID:25830920

  10. Synthesis, micellization behavior and alcohol induced amphipathic cellulose film of cellulose-based amphiphilic surfactant

    NASA Astrophysics Data System (ADS)

    Yang, Fang; Liu, Ya-nan; Yu, Jian-ling; Li, Hai-peng; Li, Gang

    2015-08-01

    This paper presented a novel preparation method of the cellulose-based amphiphilic surfactant, and the surfactant was used to prepare amphipathic cellulose membrane. The native cotton cellulose was tailored to cellulose segments in ionic liquid 1-butyl-3-methylimidazolium chloride. Then, the hydrophobic and hydrophilic modification of cellulose segments were carried out by esterification and graft polymerization of the ɛ-caprolactone (ɛ-CL) monomer onto the hydroxyl group of cellulose as well as sulphonation with sulfamic acid. The amphipathic cellulose membrane was made by cellulose-based amphiphilic surfactant cross-linking with glutaraldehyde. The molecular structure of amphipathic cellulose surfactant was confirmed by FT-IR, and its surface active properties were investigated by Wilhelmy plate method and Steady-state fluorescence probe method, respectively. Experimental results showed that cellulose-based amphiphilic surfactant caused low interfacial tension of 48.62 mN/m and its critical micelle concentration (cmc) value was 0.65 wt% when the grafting ratio of cellulose-g-PCL (poly-caprolactone) was 25.40%. The contact angle between a droplet of water and the surface of membrane was 90.84o, and the surface free energy of the alcohol induced cellulose membrane was 15.7 mJ/m2. This study may help increase using natural and biodegradable surface-activity materials with improved properties as surfactants.

  11. Prediction of long-term stability of ionic liquids at elevated temperatures by means of non-isothermal thermogravimetrical analysis.

    PubMed

    Seeberger, Andreas; Andresen, Ann-Kathrin; Jess, Andreas

    2009-11-01

    The thermal stability of an ionic liquid (IL) is an important parameter and limits the maximum operation temperature. However, the definition of stability and of the maximum operation temperature, respectively, is still an open question. Typically, non-isothermal thermogravimetrical analysis (TGA) is used to determine the stability, which is then mostly defined by the onset temperature, i.e. by the temperature where a certain mass loss of e.g. 1% is reached. Unfortunately, the rate of mass loss depends on the apparatus and conditions (e.g. heating rate), and may be governed by evaporation or by thermal decomposition or by a combination of both. In this work, isothermal as well as non-isothermal TG/DTG measurements at different heating rates were used as basis to model the combined kinetics of evaporation and decomposition, thereby taking 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [BMIM][BTA] as an example. The measured and predicted mass losses are in good agreement, and the simulation of TG/DTG experiments by the methods outlined in this work leads to a reliable estimation of the evaporation (as shown by comparison with literature data) as well as of the decomposition rate. For a closed system, where the mass loss by evaporation is negligible, a novel criterion (1% mass loss by thermal decomposition within one year) is presented to estimate the maximum operation temperature of ILs. PMID:19830320

  12. Solvent effects on the polar network of ionic liquid solutions.

    PubMed

    Bernardes, Carlos E S; Shimizu, Karina; Canongia Lopes, José N

    2015-05-20

    Molecular dynamics simulations were used to probe mixtures of ionic liquids (ILs) with common molecular solvents. Four types of systems were considered: (i) 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide plus benzene, hexafluorobenzene or 1,2-difluorobenzene mixtures; (ii) choline-based ILs plus ether mixtures (iii) choline-based ILs plus n-alkanol mixtures; and (iv) 1-butyl-3-methylimidazolium nitrate and 1-ethyl-3-methylimidazolium ethyl sulfate aqueous mixtures. The results produced a wealth of structural and aggregation information that highlight the resilience of the polar network of the ILs (formed by clusters of alternating ions and counter-ions) to the addition of different types of molecular solvent. The analysis of the MD data also shows that the intricate balance between different types of interaction (electrostatic, van der Waals, H-bond-like) between the different species present in the mixtures has a profound effect on the morphology of the mixtures at a mesoscopic scale. In the case of the IL aqueous solutions, the present results suggest an alternative interpretation for very recently published x-ray and neutron diffraction data on similar systems. PMID:25923649

  13. Synthesis of Cu, Zn and Cu/Zn brass alloy nanoparticles from metal amidinate precursors in ionic liquids or propylene carbonate with relevance to methanol synthesis.

    PubMed

    Schütte, Kai; Meyer, Hajo; Gemel, Christian; Barthel, Juri; Fischer, Roland A; Janiak, Christoph

    2014-03-21

    Microwave-induced decomposition of the transition metal amidinates {[Me(C(N(i)Pr)2)]Cu}2 (1) and [Me(C(N(i)Pr)2)]2Zn (2) in the ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIm][BF4]) or in propylene carbonate (PC) gives copper and zinc nanoparticles which are stable in the absence of capping ligands (surfactants) for more than six weeks. Co-decomposition of 1 and 2 yields the intermetallic nano-brass phases β-CuZn and γ-Cu3Zn depending on the chosen molar ratios of the precursors. Nanoparticles were characterized by high-angle annular dark field-scanning transmission electron microscopy (HAADF-STEM), dynamic light scattering and powder X-ray diffractometry. Microstructure characterizations were complemented by STEM with spatially resolved energy-dispersive X-ray spectrometry and X-ray photoelectron spectroscopy. Synthesis in ILs yields significantly smaller nanoparticles than in PC. β-CuZn alloy nanoparticles are precursors to catalysts for methanol synthesis from the synthesis gas H2/CO/CO2 with a productivity of 10.7 mol(MeOH) (kg(Cu) h)(-1). PMID:24492885

  14. Dynamics of graphene nanoribbon with carbon nanotubes coexisting with [Bmim][Cl] molecules

    NASA Astrophysics Data System (ADS)

    Li, Yunfang

    2015-09-01

    Molecular dynamics simulations have been performed to investigate the dynamics of graphene nanoribbon (GNR) on single-walled carbon nanotubes (SWNTs) coexisting with 1-butyl-3-methylimidazolium chloride ([Bmim][Cl]). The results indicate that in the wrapping and encapsulating processes when GNR interacts with SWNT, [Bmim][Cl] has an extremely different dynamics, showing an interesting dependence on tube size. Two GNRs can easily bring the [Bmim][Cl] into the hollow area of the formed double helix in the SWNT. The sequence of the interaction between these substances is E GNR-SWNT > E GNR-[Bmim][Cl] > E [Bmim][Cl]-SWNT. A high temperature will hinder the wrapping dynamics behavior of the GNR and even militate against the insertion dynamics of [Bmim][Cl]. The [Bmim][Cl] has nearly no effect on the dynamics of GNR on SWNT. Furthermore, the GNR can transport [Bmim][Cl] in the SWNT by expelling them. The proposed discoveries eventually provide a powerful way to fabricate nanoscale materials and devices and eventually tune their properties.

  15. Development and optimization of a naphthoic acid-based ionic liquid as a "non-organic solvent microextraction" for the determination of tetracycline antibiotics in milk and chicken eggs.

    PubMed

    Gao, Jiajia; Wang, Hui; Qu, Jingang; Wang, Huili; Wang, Xuedong

    2017-01-15

    In traditional ionic liquids (ILs)-based microextraction, ILs are often used as extraction and dispersive solvents; however, their functional effects are not fully utilized. Herein, we developed a novel ionic liquid 1-butyl-3-methylimidazolium naphthoic acid salt ([C4MIM][NPA]) with strong acidity. It was used as a mixed dispersive solvent with conventional [C2MIM][BF4] in "functionalized ionic liquid-based non-organic solvent microextraction (FIL-NOSM)" for determination of tetracycline antibiotics (TCs) in milk and eggs. Utilization of [C4MIM][NPA] in FIL-NOSM method increased extraction recoveries (ERs) of TCs by more than 20% and eliminated the pH adjustment step because of its strong acidity. Under optimized conditions based on central composite design, the ERs of four TCs were 94.1-102.1%, and the limitsofdetection were 0.08-1.12μgkg(-1) in milk and egg samples. This proposed method provides high extraction efficiency, less pretreatment time and requires non-organic solvents for determination of trace TC concentrations in complex animal-based food matrices. PMID:27542460

  16. Novel applications of ionic liquids in materials processing

    NASA Astrophysics Data System (ADS)

    Reddy, Ramana G.

    2009-05-01

    Ionic liquids are mixtures of organic and inorganic salts which are liquids at room temperature. Several potential applications of ionic liquids in the field of materials processing are electrowinning and electrodeposition of metals and alloys, electrolysis of active metals at low temperature, liquid-liquid extraction of metals. Results using 1-butyl-3-methylimidazolium chloride with AlCl3 at low temperatures yielded high purity aluminium deposits (>99.9% pure) and current efficiencies >98%. Titanium and aluminium were co-deposited with/without the addition of TiCl4 with up to 27 wt% Ti in the deposit with current efficiencies in the range of 78-85 %. Certain ionic liquids are potential replacements for thermal oils and molten salts as heat transfer fluids in solar energy applications due to high thermal stability, very low corrosivity and substantial sensible heat retentivity. The calculated storage densities for several chloride and fluoride ionic liquids are in the range of 160-210 MJ/m3. A 3-D mathematical model was developed to simulate the large scale electrowinning of aluminium. Since ionic liquids processing results in their low energy consumption, low pollutant emissions many more materials processing applications are expected in future.

  17. Optimization of Ionic Liquid Based Simultaneous Ultrasonic- and Microwave-Assisted Extraction of Rutin and Quercetin from Leaves of Velvetleaf (Abutilon theophrasti) by Response Surface Methodology

    PubMed Central

    Zhao, Chunjian; Lu, Zhicheng; He, Xin; Li, Zhao; Shi, Kunming; Yang, Lei; Fu, Yujie; Zu, Yuangang

    2014-01-01

    An ionic liquids based simultaneous ultrasonic and microwave assisted extraction (ILs-UMAE) method has been proposed for the extraction of rutin (RU), quercetin (QU), from velvetleaf leaves. The influential parameters of the ILs-UMAE were optimized by the single factor and the central composite design (CCD) experiments. A 2.00 M 1-butyl-3-methylimidazolium bromide ([C4mim]Br) was used as the experimental ionic liquid, extraction temperature 60°C, extraction time 12 min, liquid-solid ratio 32 mL/g, microwave power of 534 W, and a fixed ultrasonic power of 50 W. Compared to conventional heating reflux extraction (HRE), the RU and QU extraction yields obtained by ILs-UMAE were, respectively, 5.49 mg/g and 0.27 mg/g, which increased, respectively, 2.01-fold and 2.34-fold with the recoveries that were in the range of 97.62–102.36% for RU and 97.33–102.21% for QU with RSDs lower than 3.2% under the optimized UMAE conditions. In addition, the shorter extraction time was used in ILs-UMAE, compared with HRE. Therefore, ILs-UMAE was a rapid and an efficient method for the extraction of RU and QU from the leaves of velvetleaf. PMID:25243207

  18. Green synthesis of polymer monoliths incorporated with carbon nanotubes in room temperature ionic liquid and deep eutectic solvents.

    PubMed

    Zhang, Li-Shun; Gao, Shu-Ping; Huang, Yan-Ping; Liu, Zhao-Sheng

    2016-07-01

    In this work, an efficient method to prepare polymer monoliths with incorporated carbon nanotubes in a mixture of room temperature ionic liquid and deep eutectic solvents was developed. With assistance of the binary green solvent, 1-butyl-3-methylimidazolium tetrafluoroborate and choline chloride/ethylene glycol, single-walled carbon nanotubes were dispersed successfully in pre-polymerization mixture without need of oxidative cutting of carbon nanotubes, which may allow depletion of the emission of volatile organic compounds into environment. The novel single-walled carbon nanotubes monolith was evaluated by capillary electrochromatography. Compared with the monolith made without single-walled carbon nanotubes, the monolith with the incorporation of single-walled carbon nanotubes exhibited high column efficiency (251,000plates/m) in the chromatographic separation. The morphology of the monolith can be tuned by the composition of mixture of ionic liquids and deep eutectic solvents to afford good column permeability and excellent separation ability for small molecules of alkyl phenones and alkyl benzenes. The results demonstrated that the method is a green strategy for the fabrication of multifunctional polymer monoliths. PMID:27154683

  19. Influence of the ionic liquid cation on the solvent extraction of trivalent rare-earth ions by mixtures of Cyanex 923 and ionic liquids.

    PubMed

    Rout, Alok; Binnemans, Koen

    2015-01-21

    Trivalent rare-earth ions were extracted from nitric acid medium by the neutral phosphine oxide extractant Cyanex 923 into ionic liquid phases containing the bis(trifluoromethylsulfonyl)imide anion. Five different cations were considered: 1-butyl-3-methylimidazolium, 1-decyl-3-methylimidazolium, methyltributylammonium, methyltrioctylammonium and trihexyl(tetradecyl)phosphonium. The extraction behavior of neodymium(iii) was investigated as a function of various parameters: pH, extractant concentration, concentration of the neodymium(iii) ion in the aqueous feed and concentration of the salting-out agent. The loading capacity of the ionic liquid phase was studied. The extraction efficiency increased with increasing pH of the aqueous feed solution. The extraction occurred for all ionic liquids via an ion-exchange mechanism and the extraction efficiency could be related to the solubility of the ionic liquid cation in the aqueous phase: high distribution ratios for hydrophilic cations and low ones for hydrophobic cations. Addition of nitrate ions to the aqueous phase resulted in an increase in extraction efficiency for ionic liquids with hydrophobic cations due to extraction of neutral complexes. Neodymium(iii) could be stripped from the ionic liquid phase by 0.5-1.0 M nitric acid solutions and the extracting phase could be reused. The extractability of other rare earths present in the mixture was compared for the five ionic liquids. PMID:25423581

  20. Ultrasonic-electrodeposition of PtPd alloy nanoparticles on ionic liquid-functionalized graphene paper: towards a flexible and versatile nanohybrid electrode

    NASA Astrophysics Data System (ADS)

    Sun, Yimin; Zheng, Huaming; Wang, Chenxu; Yang, Mengmeng; Zhou, Aijun; Duan, Hongwei

    2016-01-01

    Here we fabricate a new type of flexible and versatile nanohybrid paper electrode by ultrasonic-electrodeposition of PtPd alloy nanoparticles on freestanding ionic liquid (IL)-functionalized graphene paper, and explore its multifunctional applications in electrochemical catalysis and sensing systems. The graphene-based paper materials demonstrate intrinsic flexibility, exceptional mechanical strength and high electrical conductivity, and therefore can serve as an ideal freestanding flexible electrode for electrochemical devices. Furthermore, the functionalization of graphene with IL (i.e., 1-butyl-3-methylimidazolium tetrafluoroborate) not only increases the electroactive surface area of a graphene-based nanohybrid paper electrode, but also improves the adhesion and dispersion of metal nanoparticles on the paper surface. These unique attributes, combined with the merits of an ultrasonic-electrodeposition method, lead to the formation of PtPd alloy nanoparticles on IL-graphene paper with high loading, uniform distribution, controlled morphology and favourable size. Consequently, the resultant nanohybrid paper electrode exhibits remarkable catalytic activity as well as excellent cycle stability and improved anti-poisoning ability towards electrooxidation of fuel molecules such as methanol and ethanol. Furthermore, for nonenzymatic electrochemical sensing of some specific biomarkers such as glucose and reactive oxygen species, the nanohybrid paper electrode shows high selectivity, sensitivity and biocompatibility in these bio-catalytic processes, and can be used for real-time tracking hydrogen peroxide secretion by living human cells. All these features demonstrate its promising application as a versatile nanohybrid electrode material in flexible and lightweight electrochemical energy conversion and biosensing systems such as bendable on-chip power sources, wearable/implantable detectors and in vivo micro-biosensors.Here we fabricate a new type of flexible and

  1. Video-microscopic observation of ionic liquid/alcohol interface and the corresponding molecular simulation study

    NASA Astrophysics Data System (ADS)

    Zhu, Peixi

    This research is aimed at studying the ionic liquid/n-pentanol interface via video-microscopy and molecular dynamic simulations. Understanding the interfacial phenomena and interfacial transport between ionic liquids and other liquids is of interest to the development and application of ionic liquids in a number of areas. One such area is the biphasic hydroformylation of alkenes to obtain alcohol and aldehyde, in which case ionic liquid is the reaction medium where a catalyst resides. The dissolution of an ionic liquid into an alcohol was studied by microscopically observing and measuring the shrinking of a micropipette-produced droplet in real time. Although microscopic investigation of droplet dissolution has been studied before, no attempt had been made to measure the diffusion coefficient D of the droplet species in the surrounding medium. A key finding of this work is that the Epstein-Plesset mathematical model, which describes the dissolution of a droplet/bubble in another fluid medium, can be used to measure D. Other experimental studies of the ionic liquid/alcohol system include electrical conductivity and UV-visible spectroscopy measurements of solutions of 1-hexyl-3-methylimidazolium tetrafluoroborate in n-pentanol. Those experiments were done in order to understand the molecular state of the particular ionic liquid in n-pentanol, as well as obtaining the dissociation constant K of such weak electrolyte solution. The experimental results provide an entry to the assessment of ionic liquid interaction with n-pentanol at molecular scale. Subsequently, molecular dynamics simulation was implemented for the investigation of such interaction. The computation started with simulation of the bulk phase of 1-butyl-3-methylimidazolium tetrafluoroborate, an affine ionic liquid on which molecular simulations had already been reported. A generalized probability based on Fuoss approximation for the closest ion to a distinguished countercharge ion was developed. In

  2. Ultrasonic-electrodeposition of PtPd alloy nanoparticles on ionic liquid-functionalized graphene paper: towards a flexible and versatile nanohybrid electrode

    NASA Astrophysics Data System (ADS)

    Sun, Yimin; Zheng, Huaming; Wang, Chenxu; Yang, Mengmeng; Zhou, Aijun; Duan, Hongwei

    2016-01-01

    Here we fabricate a new type of flexible and versatile nanohybrid paper electrode by ultrasonic-electrodeposition of PtPd alloy nanoparticles on freestanding ionic liquid (IL)-functionalized graphene paper, and explore its multifunctional applications in electrochemical catalysis and sensing systems. The graphene-based paper materials demonstrate intrinsic flexibility, exceptional mechanical strength and high electrical conductivity, and therefore can serve as an ideal freestanding flexible electrode for electrochemical devices. Furthermore, the functionalization of graphene with IL (i.e., 1-butyl-3-methylimidazolium tetrafluoroborate) not only increases the electroactive surface area of a graphene-based nanohybrid paper electrode, but also improves the adhesion and dispersion of metal nanoparticles on the paper surface. These unique attributes, combined with the merits of an ultrasonic-electrodeposition method, lead to the formation of PtPd alloy nanoparticles on IL-graphene paper with high loading, uniform distribution, controlled morphology and favourable size. Consequently, the resultant nanohybrid paper electrode exhibits remarkable catalytic activity as well as excellent cycle stability and improved anti-poisoning ability towards electrooxidation of fuel molecules such as methanol and ethanol. Furthermore, for nonenzymatic electrochemical sensing of some specific biomarkers such as glucose and reactive oxygen species, the nanohybrid paper electrode shows high selectivity, sensitivity and biocompatibility in these bio-catalytic processes, and can be used for real-time tracking hydrogen peroxide secretion by living human cells. All these features demonstrate its promising application as a versatile nanohybrid electrode material in flexible and lightweight electrochemical energy conversion and biosensing systems such as bendable on-chip power sources, wearable/implantable detectors and in vivo micro-biosensors.Here we fabricate a new type of flexible and

  3. Rational Design of Bi Nanoparticles for Efficient Electrochemical CO2 Reduction: The Elucidation of Size and Surface Condition Effects

    DOE PAGESBeta

    Zhang, Zhiyong; Chi, Miaofang; Veith, Gabriel M.; Zhang, Pengfei; Lutterman, Daniel A.; Rosenthal, Joel; Overbury, Steven H.; Dai, Sheng; Zhu, Huiyuan

    2016-08-08

    Here we report an efficient electrochemical conversion of CO2 to CO on surface-activated bismuth nanoparticles (NPs) in acetonitrile (MeCN) under ambient conditions, with the assistance of 1-butyl-3-methylimidazolium trifluoromethanesulfonate ([bmim][OTf]). Through the comparison between electrodeposited Bi films (Bi-ED) and different types of Bi NPs, we, for the first time, demonstrate the effects of catalyst’s size and surface condition on organic phase electrochemical CO2 reduction. Our study reveals that the surface inhibiting layer (hydrophobic surfactants and Bi3+ species) formed during the synthesis and purification process hinders the CO2 reduction, leading to a 20% drop in Faradaic efficiency for CO evolution (FECO). Bimore » particle size showed a significant effect on FECO when the surface of Bi was air-oxidized, but this effect of size on FECO became negligible on surface-activated Bi NPs. After the surface activation (hydrazine treatment) that effectively removed the native inhibiting layer, activated 36-nm Bi NPs exhibited an almost-quantitative conversion of CO2 to CO (96.1% FECO), and a mass activity for CO evolution (MACO) of 15.6 mA mg–1, which is three-fold higher than the conventional Bi-ED, at ₋2.0 V (vs Ag/AgCl). Ultimately, this work elucidates the importance of the surface activation for an efficient electrochemical CO2 conversion on metal NPs and paves the way for understanding the CO2 electrochemical reduction mechanism in nonaqueous media.« less

  4. Separation and Determination of Four Tanshinones in Danshen and Related Medicinal Plants by Micellar Electrokinetic Chromatography Using Ionic Liquids as Modifier.

    PubMed

    Cao, Jiliang; Wei, Jinchao; Xiang, Cheng; Zhang, Mi; Li, Baocai; Wan, Jianbo; Su, Huanxing; Li, Peng

    2016-09-01

    A simple and fast micellar electrokinetic chromatography (MEKC) method using ionic liquids as modifier was established for simultaneous determination of four hydrophobic tanshinones, including dihydrotanshinone I ( 1: ), cryptotanshinone ( 2: ), tanshinone I ( 3: ) and tanshinone IIA ( 4: ), in Danshen and related medicinal plants. In normal MEKC using sodium dodecyl sulfate (SDS) as surfactant and organic solvents as additives, the four tanshinones, especially cryptotanshinone and tanshinone I, could not be well separated. Fortunately, further addition of ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim]BF4) resulted in a baseline separation of these four analytes. After an optimization study, 10 mM borax-10 mM SDS-10 mM [bmim]BF4 containing 15% acetonitrile (v/v) at pH 9.6 was adopted as the running buffer to complete the separation within 16 min at the voltage of 25 kV, temperature of 25°C and detection wavelength of 254 nm. The relative standard deviations of migration time and peak area were in the range of 0.62-2.21 and 1.33-3.90%, respectively, indicating the good repeatability of the developed method. This method was extensively validated by evaluating the linearity (R(2) ≥ 0.9992), limits of detection (0.75-1.11 μg mL(-1)), limits of quantification (2.26-3.32 μg mL(-1)) and recovery (96.11-103.74%). Under the optimum conditions, samples of Danshen and related medicinal plants were well analyzed with high separation efficiency. PMID:27139739

  5. Development of a novel naphthoic acid ionic liquid and its application in "no-organic solvent microextraction" for determination of triclosan and methyltriclosan in human fluids and the method optimization by central composite design.

    PubMed

    Wang, Hui; Gao, Jiajia; Yu, Nana; Qu, Jingang; Fang, Fang; Wang, Huili; Wang, Mei; Wang, Xuedong

    2016-07-01

    In traditional ionic liquids (ILs)-based microextraction, the hydrophobic and hydrophilic ILs are often used as extractant and disperser, respectively. However, the functional effects of ILs are not utilized in microextraction procedures. Herein, we introduced 1-naphthoic acid into imidazolium ring to synthesize a novel ionic liquid 1-butyl-3-methylimidazolium naphthoic acid salt ([C4MIM][NPA]), and its structure was characterized by IR, (1)H NMR and MS. On the basis of its acidic property and lower solubility than common [CnMIM][BF4], it was used as a mixing dispersive solvent with [C4MIM][BF4] in "functionalized ionic liquid-based no organic solvent microextraction (FIL-NOSM)". Utilization of [C4MIM][NPA] in FIL-NOSM procedures has two obvious advantages: (1) it promoted the non-polar environment, increased volume of the sedimented phase, and thus could enhance the extraction recoveries of triclosan (TCS) and methyltriclosan (MTCS) by more than 10%; and (2) because of the acidic property, it can act as a pH modifier, avoiding extra pH adjustment step. By combining single factor optimization and central composite design, the main factors in the FIL-NOSM method were optimized. Under the optimal conditions, the relative recoveries of TCS and MTCS reached up to 98.60-106.09%, and the LODs of them were as low as 0.12-0.15µgL(-1) in plasma and urine samples. In total, this [C4MIM][NPA]-based FIL-NOSM method provided high extraction efficiency, and required less pretreatment time and unutilized any organic solvent. To the best of our knowledge, this is the first application of [C4mim][NPA]-based microextraction method for the simultaneous quantification of trace TCS and MTCS in human fluids. PMID:27154690

  6. Extraction and determination of chloramphenicol in feed water, milk, and honey samples using an ionic liquid/sodium citrate aqueous two-phase system coupled with high-performance liquid chromatography.

    PubMed

    Han, Juan; Wang, Yun; Yu, Cui-lan; Yan, Yong-sheng; Xie, Xue-qiao

    2011-01-01

    A green, simple, non-toxic, and sensitive sample pretreatment procedure coupled with high-performance liquid chromatography (HPLC) was developed for the analysis of chloramphenicol (CAP) that exploits an aqueous two-phase system based on imidazolium ionic liquid (1-butyl-3-methylimidazolium tetrafluoroborate, [Bmim]BF(4)) and organic salt (Na(3)C(6)H(5)O(7)) using a liquid-liquid extraction technique. The influence factors on partition behaviors of CAP were studied, including the type and amount of salts, the pH value, the volume of [Bmim]BF(4), and the extraction temperature. Extraction efficiency of the CAP was found to increase with increasing temperature and the volume of [Bmim]BF(4). Thermodynamic studies indicated that hydrophobic interactions were the main driving force, although electrostatic interactions and salting-out effects were also important for the transfer of the CAP. Under the optimal conditions, 90.1% of the CAP could be extracted into the ionic liquid-rich phase in a single-step extraction. This method was practical when applied to the analysis of CAP in feed water, milk, and honey samples with a linear range of 2~1,000 ng mL(-1). The method yielded a limit of detection of 0.3 ng mL(-1) and a limit of quantification of 1.0 ng mL(-1). The recovery of CAP was 90.4-102.7% from aqueous samples of real feed water, milk, and honey samples by the proposed method. This novel process is much simpler and more environmentally friendly and is suggested to have important applications for the separation of antibiotics. PMID:21063686

  7. Separation, concentration and determination of chloramphenicol in environment and food using an ionic liquid/salt aqueous two-phase flotation system coupled with high-performance liquid chromatography.

    PubMed

    Han, Juan; Wang, Yun; Yu, Cuilan; Li, Chunxiang; Yan, Yongsheng; Liu, Yan; Wang, Liang

    2011-01-31

    Ionic liquid-salt aqueous two-phase flotation (ILATPF) is a novel, green, non-toxic and sensitive samples pretreatment technique. ILATPF coupled with high-performance liquid chromatography (HPLC) was developed for the analysis of chloramphenicol, which combines ionic liquid aqueous two-phase system (ILATPS) based on imidazolium ionic liquid (1-butyl-3-methylimidazolium chloride, [C(4)mim]Cl) and inorganic salt (K(2)HPO(4)) with solvent sublation. In ILATPF systems, phase behaviors of the ILATPF were studied for different types of ionic liquids and salts. The sublation efficiency of chloramphenicol in [C(4)mim]Cl-K(2)HPO(4) ILATPF was influenced by the types of salts, concentration of K(2)HPO(4) in aqueous solution, solution pH, nitrogen flow rate, sublation time and the amount of [C(4)mim]Cl. Under the optimum conditions, the average sublation efficiency is up to 98.5%. The mechanism of ILATPF contains two principal processes. One is the mechanism of IL-salt ILATPS formation, the other is solvent sublation. This method was practical when applied to the analysis of chloramphenicol in lake water, feed water, milk, and honey samples with the linear range of 0.5-500 ng mL(-1). The method yielded limit of detection (LOD) of 0.1 ng mL(-1) and limit of quantification (LOQ) of 0.3 ng mL(-1). The recovery of CAP was 97.1-101.9% from aqueous samples of environmental and food samples by the proposed method. Compared with liquid-liquid extraction, solvent sublation and ionic liquid aqueous two-phase extraction, ILATPF can not only separate and concentrate chloramphenicol with high sublation efficiency, but also efficiently reduce the wastage of IL. This novel technique is much simpler and more environmentally friendly and is suggested to have important applications for the concentration and separation of other small biomolecules. PMID:21168562

  8. Effect of ion structure on conductivity in lithium-doped ionic liquid electrolytes: A molecular dynamics study

    NASA Astrophysics Data System (ADS)

    Liu, Hongjun; Maginn, Edward

    2013-09-01

    Molecular dynamics simulations were performed to examine the role cation and anion structure have on the performance of ionic liquid (IL) electrolytes for lithium conduction over the temperature range of 320-450 K. Two model ionic liquids were studied: 1-butyl-3-methylimidazolium bis[(trifluoromethyl)sulfonyl]imide ([bmim][Tf2N]) and 1-butyl-4-methylpyridinium pyrrolide ([bmpyr][pyl]) doped with Li[Tf2N] and Li[pyl], respectively. The results have demonstrated that the Li+ doped IL containing the planar [bmpyr] cation paired with the planar [pyl] anion significantly outperformed the [bmim][Tf2N] IL. The different coordination of Li+ with the [Tf2N]- or [pyl]- anions produces a remarkable change in IL structure with a concomitant effect on the transport of all ions. For the doped [bmim][Tf2N], each Li+ is coordinated by four oxygen atoms from [Tf2N]- anions. Formation of a rigid structure between Li+ and [Tf2N]- induces a decrease in the mobility of all ions. In contrast, for the doped [bmpyr][pyl], each Li+ is coordinated by two nitrogen atoms from [pyl]- anions. The original alternating structure cation|anion|cation in the neat [bmpyr][pyl] is replaced by another alternating structure cation|anion|Li+|anion|cation in the doped [bmpyr][pyl]. Increases of Li+ mole fraction in doped [bmpyr][pyl] affects the dynamics to a much lesser extent compared with [bmim][Tf2N] and leads to reduced diffusivities of cations and anions, but little change in the dynamics of Li+. More importantly, the calculations predict that the Li+ ion conductivity of doped [bmpyr][pyl] is comparable to that observed in organic liquid electrolytes and is about an order of magnitude higher than that of doped [bmim][Tf2N]. Such Li+ conductivity improvement suggests that this and related ILs may be promising candidates for use as electrolytes in lithium ion batteries and capacitors.

  9. Base-Promoted Ammonia Borane Hydrogen-Release

    SciTech Connect

    Himmelberger, Daniel W.; Yoon, Chang W.; Bluhm, Martin E.; Carroll, Patrick J.; Sneddon, Larry G.

    2009-10-07

    The strong non-nucleophilic base bis(dimethylamino)naphthalene (Proton Sponge, PS) has been found to promote the rate and extent of H2-release from ammonia borane (AB) either in the solid state or in ionic-liquid and tetraglyme solutions. For example, AB reactions in 1-butyl-3-methylimidazolium chloride (bmimCl) containing 5.3 mol % PS released 2 equiv of H2 in 171 min at 85 °C and only 9 min at 110 °C, whereas comparable reactions without PS required 316 min at 85 °C and 20 min at 110 °C. Ionic-liquid solvents proved more favorable than tetraglyme since they reduced the formation of undesirable products such as borazine. Solid-state and solution 11B NMR studies of PS-promoted reactions in progress support a reaction pathway involving initial AB deprotonation to form the H3BNH2 - anion. This anion can then initiate AB dehydropolymerization to form branched-chain polyaminoborane polymers. Subsequent chain-branching and dehydrogenation reactions lead ultimately to a cross-linked polyborazylene-type product. AB dehydrogenation by lithium and potassium triethylborohydride was found to produce the stabilized Et3BNH2BH3 - anion, with the crystallographically determined structure of the [Et3BNH2BH3]-K+ · 18-crown-6 complex showing that, following AB nitrogen-deprotonation by the triethylborohydride, the Lewis-acidic triethylborane group coordinated at the nitrogen. Model studies of the reactions of [Et3BNH2BH3]-Li+ with AB show evidence of chain-growth, providing additional support for a PS-promoted AB anionic dehydropolymerization H2- release process.

  10. An electrochemical gas sensor based on paper supported room temperature ionic liquids.

    PubMed

    Dossi, Nicolò; Toniolo, Rosanna; Pizzariello, Andrea; Carrilho, Emanuel; Piccin, Evandro; Battiston, Simone; Bontempelli, Gino

    2012-01-01

    A sensitive and fast-responding membrane-free amperometric gas sensor is described, consisting of a small filter paper foil soaked with a room temperature ionic liquid (RTIL), upon which three electrodes are screen printed with carbon ink, using a suitable mask. It takes advantage of the high electrical conductivity and negligible vapour pressure of RTILs as well as their easy immobilization into a porous and inexpensive supporting material such as paper. Moreover, thanks to a careful control of the preparation procedure, a very close contact between the RTIL and electrode material can be achieved so as to allow gaseous analytes to undergo charge transfer just as soon as they reach the three-phase sites where the electrode material, paper supported RTIL and gas phase meet. Thus, the adverse effect on recorded currents of slow steps such as analyte diffusion and dissolution in a solvent is avoided. To evaluate the performance of this device, it was used as a wall-jet amperometric detector for flow injection analysis of 1-butanethiol vapours, adopted as the model gaseous analyte, present in headspace samples in equilibrium with aqueous solutions at controlled concentrations. With this purpose, the RTIL soaked paper electrochemical detector (RTIL-PED) was assembled by using 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide as the wicking RTIL and printing the working electrode with carbon ink doped with cobalt(II) phthalocyanine, to profit from its ability to electrocatalyze thiol oxidation. The results obtained were quite satisfactory (detection limit: 0.5 μM; dynamic range: 2-200 μM, both referring to solution concentrations; correlation coefficient: 0.998; repeatability: ±7% RSD; long-term stability: 9%), thus suggesting the possible use of this device for manifold applications. PMID:22076475

  11. Molecular simulation and experimental study of CO2 absorption in ionic liquid reverse micelle.

    PubMed

    Shi, Wei; Hong, Lei; Damodaran, Krishnan; Nulwala, Hunaid B; Luebke, David R

    2014-12-01

    The structure and dynamics for CO2 absorption in ionic liquid reverse micelle (ILRM) were studied using molecular simulations. The ILRM consisted of 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF4]) ionic liquid (IL) as the micelle core, the benzylhexadecyldimethylammonium ([BHD](+)) chloride ([Cl](-)) was the cationic surfactant, and benzene was used as the continuous solvent phase in this study. The diffusivity values of this ILRM system were also experimentally determined. Simulations indicate that there is ion exchange between the IL anion ([BF4](-)) and the surfactant anion ([Cl](-)). It was also found that the [bmim][BF4] IL exhibits small local density at the interface region between the IL core and the [BHD](+) surfactant cation layer, which leads to a smaller density for the [bmim][BF4] IL inside the reverse micelle (RM) compared with the neat IL. These simulation findings are consistent with experimental results. Both our simulations and experimental results show that [bmim][BF4] inside the RM diffuses 5-26 times faster than the neat IL, which is partly due to the fast particle diffusion for the ILRM nanodroplet (IL and surfactant) as a whole in benzene solvent compared with neat [bmim][BF4] diffusion. Additionally, it was found that [bmim][BF4] IL solved in benzene diffuses 2 orders of magnitude faster than the neat IL. Lastly, simulations show that CO2 molecules are absorbed in four different regions of the ILRM system, that is, (I) in the IL inner core, (II) in the [BHD](+) surfactant cation layer, (III) at the interface between the [BHD](+) surfactant cation layer and benzene solvent, and (IV) in the benzene solvent. The CO2 solubility was found to decrease in the order II > III ∼ IV > I, while the CO2 diffusivity and permeability decrease in the following order: IV > III > II > I. PMID:25382316

  12. Comparison of interionic/intermolecular vibrational dynamics between ionic liquids and concentrated electrolyte solutions.

    PubMed

    Fujisawa, Tomotsumi; Nishikawa, Keiko; Shirota, Hideaki

    2009-12-28

    In this study, we have compared the interionic/intermolecular vibrational dynamics of ionic liquids (ILs) and concentrated electrolyte solutions measured by femtosecond optically heterodyne-detected Raman-induced Kerr effect spectroscopy. A typical anion in ILs, bis(trifluoromethanesulfonyl)amide ([NTf(2)](-)), has been chosen as the anion for the sample ILs and concentrated electrolyte solutions. ILs used in this study are 1-butyl-3-methylimidazolium, 1-butylpyridinium, N-butyl-N,N,N-triethylammonium, and 1-butyl-1-methylpyrrolidinium with [NTf(2)](-). Li[NTf(2)] solutions (approximately 3.3 M) of water, methanol, propylene carbonate, and poly(ethylene glycol) have been selected as control samples. Kerr transients of the ILs and electrolyte solutions show intra- and interionic/intermolecular vibrational dynamics followed by slow picosecond overdamped relaxation. Fourier transform Kerr spectra have shown a difference in the relative intensities of intraionic vibrational bands of [NTf(2)](-) (280-350 cm(-1)) between the ILs and electrolyte solutions. The origin of the difference is attributed to the change in the conformational equilibrium between cisoid and transoid forms of [NTf(2)](-), which is caused by a favorable stabilization of dipolar cisoid form due to Li(+) and dipolar solvent molecules in the electrolyte solutions. Low-frequency Kerr spectra (0-200 cm(-1)) exhibit unique features with the variation of cation and solvent species. The aromatic ILs have a prominent high-frequency librational motion at about 100 cm(-1) in contrast to the case for the nonaromatic ones. The common structure of the spectra observed at about 20 cm(-1) likely comes from an interionic motion of [NTf(2)](-). The nonaromatic ILs allow a fair comparison with the electrolyte solutions of propylene carbonate and poly(ethylene glycol) because of the structural similarities. The comparison based on the first moment of the interionic/intermolecular vibrational spectrum suggests the

  13. Universality of Viscosity Dependence of Translational Diffusion Coefficients of Carbon Monoxide, Diphenylacetylene, and Diphenylcyclopropenone in Ionic Liquids under Various Conditions.

    PubMed

    Kimura, Y; Kida, Y; Matsushita, Y; Yasaka, Y; Ueno, M; Takahashi, K

    2015-06-25

    Translational diffusion coefficients of diphenylcyclopropenone (DPCP), diphenylacetylene (DPA), and carbon monoxide (CO) in 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([BMIm][NTf2]) and 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([EMIm][NTf2]) were determined by the transient grating (TG) spectroscopy under pressure from 0.1 to 200 MPa at 298 K and from 298 to 373 K under 0.1 MPa. Diffusion coefficients of these molecules at high temperatures in tributylmethylphosphonium bis(trifluoromethanesulfonyl)imide ([P4441][NTf2]), and tetraoctylphosphonium bis(trifluoromethanesulfonyl)imide ([P8888][NTf2]), and also in the mixtures of [BMIm][NTf2], N-methyl-N-propylpiperidinium bis(trifluoromethanesulfonyl)imide ([Pp13][NTf2]), and trihexyltetradecylphosphonium bis(trifluoromethanesulfonyl)imide ([P66614][NTf2]) with ethanol or chloroform have been determined. Diffusion coefficients except in ILs of phosphonium cations were well scaled by the power law of T/η, i.e., (T/η)(P), where T and η are the absolute temperature and the viscosity, irrespective of the solvent species, pressure and temperature, and the compositions of mixtures. The values of the exponent P were smaller for the smaller size of the molecules. On the other hand, the diffusion coefficients in ILs of phosphonium cations with longer alkyl chains were larger than the values expected from the correlation obtained by other ILs and conventional liquids. The deviation becomes larger with increasing the number of carbon atoms of alkyl-chain of cation, and with decreasing the molecular size of diffusing molecules. The molecular size dependence of the diffusion coefficient was correlated by the ratio of the volume of the solute to that of the solvent as demonstrated by the preceding work (Kaintz et al., J. Phys. Chem. B 2013 , 117 , 11697 ). Diffusion coefficients have been well correlated with the power laws of both T/η and the relative volume of the solute to the solvent

  14. Dual-Frequency Alternating Current Designer Waveform for Reliable Voltammetric Determination of Electrode Kinetics Approaching the Reversible Limit.

    PubMed

    Li, Jiezhen; Bentley, Cameron L; Bond, Alan M; Zhang, Jie

    2016-02-16

    Alternating current (ac) voltammetry provides access to faster electrode kinetics than direct current (dc) methods. However, difficulties in ac and other methods arise when the heterogeneous electron-transfer rate constant (k(0)) approaches the reversible limit, because the voltammetric characteristics become insensitive to electrode kinetics. Thus, in this near-reversible regime, even small uncertainties associated with bulk concentration (C), diffusion coefficient (D), electrode area (A), and uncompensated resistance (Ru) can lead to significant systematic error in the determination of k(0). In this study, we have introduced a kinetically sensitive dual-frequency designer waveform into the Fourier-transformed large-amplitude alternating current (FTAC) voltammetric method that is made up of two sine waves having the same amplitude but with different frequencies (e.g., 37 and 615 Hz) superimposed onto a dc ramp to quantify the close-to-reversible Fc(0/+) process (Fc = ferrocene) in two nonhaloaluminate ionic liquids. The concept is that from a single experiment the lower-frequency data set, collected on a time scale where the target process is reversible, can be used as an internal reference to calibrate A, D, C, and Ru. These calibrated values are then used to calculate k(0) from analysis of the harmonics of the higher-frequency data set, where the target process is quasi-reversible. With this approach, k(0) values of 0.28 and 0.11 cm·s(-1) have been obtained at a 50 μm diameter platinum microdisk electrode for the close-to-diffusion-controlled Fc(0/+) process in two ionic liquids, 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide and 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide, respectively. PMID:26771276

  15. Elucidation of the effect of ionic liquid pretreatment on rice husk via structural analyses

    PubMed Central

    2012-01-01

    Background In the present study, three ionic liquids, namely 1-butyl-3-methylimidazolium chloride ([BMIM]Cl), 1-ethyl-3-methylimidazolium acetate ([EMIM]OAc), and 1-ethyl-3-methylimidazolium diethyl phosphate ([EMIM]DEP), were used to partially dissolve rice husk, after which the cellulose were regenerated by the addition of water. The aim of the investigation is to examine the implications of the ionic liquid pretreatments on rice husk composition and structure. Results From the attenuated total reflectance Fourier transform-infrared (ATR FT-IR) spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM) results, the regenerated cellulose were more amorphous, less crystalline, and possessed higher structural disruption compared with untreated rice husk. The major component of regenerated cellulose from [BMIM]Cl and [EMIM]DEP pretreatments was cellulose-rich material, while cellulose regenerated from [EMIM]OAc was a matrix of cellulose and lignin. Cellulose regenerated from ionic pretreatments could be saccharified via enzymatic hydrolysis, and resulted in relatively high reducing sugars yields, whereas enzymatic hydrolysis of untreated rice husk did not yield reducing sugars. Rice husk residues generated from the ionic liquid pretreatments had similar chemical composition and amorphousity to that of untreated rice husk, but with varying extent of surface disruption and swelling. Conclusions The structural architecture of the regenerated cellulose and rice husk residues showed that they could be used for subsequent fermentation or derivation of cellulosic compounds. Therefore, ionic liquid pretreatment is an alternative in the pretreatment of lignocellulosic biomass in addition to the conventional chemical pretreatments. PMID:22958710

  16. Reusable manganese compounds containing pyrazole-based ligands for olefin epoxidation reactions.

    PubMed

    Manrique, Ester; Poater, Albert; Fontrodona, Xavier; Solà, Miquel; Rodríguez, Montserrat; Romero, Isabel

    2015-10-28

    We describe the synthesis of new manganese(ii) and manganese(iii) complexes containing the bidentate ligands 2-(3-pyrazolyl)pyridine, pypz-H, and 3(5)-(2-hydroxyphenyl)pyrazole, HOphpz-H, with formula [MnX2(pypz-H)2] (X = Cl(-), 1, CF3SO3(-), 2, OAc(-), 3 or NO3(-) (4)), [MnCl2(pypz-H)(H2O)2], 5, or [MnCl(Ophpz-H)2], 6. All the complexes have been characterized through analytical, spectroscopic and electrochemical techniques. Single X-ray structure analysis revealed a six-coordinated Mn(ii) ion in complexes 1-5, and a five-coordinated Mn(iii) ion in complex 6. Compound 5 is the first co-crystal of Mn(ii) containing Cl and H2O ligands together with bidentate nitrogen ligands. The catalytic activity of complexes 1-6 has been tested with regard to the epoxidation of styrene and, in the case of 1, 5 and 6, other alkenes have been epoxidized using peracetic acid as oxidant in different media, among which glycerol, a green solvent never used in epoxidation reactions using peracetic acid as oxidant. The catalysts show moderate to high conversions and selectivities towards the corresponding epoxides. For complexes 1, 5 and 6, a certain degree of cis→trans isomerization is observed in the case of cis-β-methylstyrene. These observations have been explained through computational calculations. The reutilization of catalysts 1 and 6 for the epoxidation of alkenes has been evaluated in [bmim] : acetonitrile mixture (bmim = 1-butyl-3-methylimidazolium), allowing the effective recyclability of the catalytic system and keeping high conversion and selectivity values up to 12 successive runs, in all cases. PMID:26389716

  17. Determination of triazine herbicides in fresh vegetables by dynamic microwave-assisted extraction coupled with homogeneous ionic liquid microextraction high performance liquid chromatography.

    PubMed

    Wu, Lijie; Hu, Mingzhu; Li, Zhanchao; Song, Ying; Yu, Cui; Zhang, Yupu; Zhang, Hanqi; Yu, Aimin; Ma, Qiang; Wang, Ziming

    2015-02-01

    A novel extraction method, dynamic microwave-assisted extraction coupled with homogeneous ionic liquid microextraction, was developed for the determination of triazine herbicides, including desmetryn, terbumeton, propazine, terbuthylazine, dimethametryn, and dipropetryn in fresh vegetable samples by high performance liquid chromatography (HPLC). In the developed method, 120 μL of 1-butyl-3-methylimidazolium tetrafluoroborate ([C4MIM][BF4]) was added to 10 mL of aqueous solution containing 0.3 g of NaCl to obtained the extraction solvent. Six triazines could be extracted completely within 4 min by the present method. Then, [NH4][PF6] was added into the extract to form a water-insoluble ionic liquid [C4MIM][PF6] via a simple metathesis reaction, and the analytes were enriched into the ionic liquid phase. After centrifugation and dilution with acetonitrile, the resulting solution was analyzed directly by HPLC. The effects of some experimental parameters, including type and volume of ionic liquid, volume of extraction solvent, amount of ion-pairing agent [NH4][PF6], salt concentration, microwave power, and flow rate of extraction solvent on the extraction efficiency were investigated and optimized. Under the optimum experimental conditions, the linearity for determining the analytes was in the range of 2.50-250.00 μg kg(-1), with the correlation coefficients ranging from 0.9989 to 0.9999. When the present method was applied to the analysis of vegetable samples, satisfactory recoveries were obtained in the range of 76.8%-106.9%, and relative standard deviations were lower than 9.8%. PMID:25542578

  18. Comparison of interionic/intermolecular vibrational dynamics between ionic liquids and concentrated electrolyte solutions

    NASA Astrophysics Data System (ADS)

    Fujisawa, Tomotsumi; Nishikawa, Keiko; Shirota, Hideaki

    2009-12-01

    In this study, we have compared the interionic/intermolecular vibrational dynamics of ionic liquids (ILs) and concentrated electrolyte solutions measured by femtosecond optically heterodyne-detected Raman-induced Kerr effect spectroscopy. A typical anion in ILs, bis(trifluoromethanesulfonyl)amide ([NTf2]-), has been chosen as the anion for the sample ILs and concentrated electrolyte solutions. ILs used in this study are 1-butyl-3-methylimidazolium, 1-butylpyridinium, N-butyl-N,N,N-triethylammonium, and 1-butyl-1-methylpyrrolidinium with [NTf2]-. Li[NTf2] solutions (˜3.3M) of water, methanol, propylene carbonate, and poly(ethylene glycol) have been selected as control samples. Kerr transients of the ILs and electrolyte solutions show intra- and interionic/intermolecular vibrational dynamics followed by slow picosecond overdamped relaxation. Fourier transform Kerr spectra have shown a difference in the relative intensities of intraionic vibrational bands of [NTf2]- (280-350 cm-1) between the ILs and electrolyte solutions. The origin of the difference is attributed to the change in the conformational equilibrium between cisoid and transoid forms of [NTf2]-, which is caused by a favorable stabilization of dipolar cisoid form due to Li+ and dipolar solvent molecules in the electrolyte solutions. Low-frequency Kerr spectra (0-200 cm-1) exhibit unique features with the variation of cation and solvent species. The aromatic ILs have a prominent high-frequency librational motion at about 100 cm-1 in contrast to the case for the nonaromatic ones. The common structure of the spectra observed at about 20 cm-1 likely comes from an interionic motion of [NTf2]-. The nonaromatic ILs allow a fair comparison with the electrolyte solutions of propylene carbonate and poly(ethylene glycol) because of the structural similarities. The comparison based on the first moment of the interionic/intermolecular vibrational spectrum suggests the stronger interionic/intermolecular interaction in

  19. Rapid and sensitive analysis of microcystins using ionic liquid-based in situ dispersive liquid-liquid microextraction.

    PubMed

    Yu, Honglian; Clark, Kevin D; Anderson, Jared L

    2015-08-01

    Three structurally different ionic liquids (ILs), namely 1-butyl-3-methylimidazolium chloride ([BMIM][Cl]), 1-(6-hydroxyethyl)-3-methylimidazolium chloride ([HeOHMIM][Cl]) and 1-benzyl-3-(2-hydroxyethyl)imidazolium bromide ([BeEOHIM][Br]), were applied as extraction solvents using in situ dispersive liquid-liquid microextraction (in situ DLLME) for the preconcentration of two microcystin variants, microcystin-RR (MC-RR) and microcystin-LR (MC-LR) from aqueous samples. Extraction parameters including sample solution pH, ratio of IL to metathesis reagent, sample volume, IL quantity, and salt concentration were optimized to achieve the best extraction efficiency. The [BeEOHIM][Br] IL, which contains both an aromatic moiety and a hydroxyl group within its chemical structure, exhibited superior extraction efficiency compared to the other two ILs. The analytical performance of the [BeEOHIM][Br] IL as an extraction solvent for in situ DLLME of microcystins was investigated using HPLC-UV and HPLC-MS. The limits of detection (LODs) for MC-RR and MC-LR were 0.7μgL(-1) using UV detection with a linear range from 1 to 50μgL(-1). The separation method was successfully adapted for ESI-MS/SIM detection, wherein the LODs for MC-RR and MC-LR were greatly improved to 0.005 and 0.003μgL(-1), respectively. The accuracy of the method was demonstrated by examining the relative recovery using tap water and river water and produced recoveries ranging from 45.0 to 109.7% and from 46.3 to 103.2%, respectively. PMID:26087964

  20. Ionic liquids as a key medium for efficient extraction of copper complexes from chia seeds (Salvia hispanica L.).

    PubMed

    Wojcieszek, Justyna; Popowski, Dominik; Ruzik, Lena

    2016-05-15

    Due to insufficient information, the aim of study was to concern on the optimization of extraction procedure of selected metal complexes with flavonoids from chia seeds. Evaluation of the amount of elements in compound, not only their total concentration content, is highly important due to the fact, that only a part from total content of metal is absorbed by human body. At the beginning the total amount of elements in chia seeds was established as 14.51±0.42 µg g(-1) for copper, 57.44±1.23 µg g(-1) for manganese, 81.12±1.89 µg g(-1) for zinc and 0.35±0.13 µg g(-1) for cobalt. After the most suitable solvent was established, effects of several parameters on the efficiency of metal extraction were studied. Solvent concentration, solid-solvent ratio, extraction method, extraction time and temperature have been investigated as independent variables. The optimal extraction conditions included vortexing during 20 min in 50°C, using an ionic liquid (1-butyl-3-methylimidazolium bromide) as an extractant, with solid-solvent ratio of 1:20. The determination of total and extractable amount of metals in chia seeds was carried out by standalone ICP MS. In addition, a complementary analysis of extracted metal complexes was performed using SEC-ICP MS method. It was confirmed that the ionic liquid is able to extract different copper complexes in comparison with commonly used solvents. The study indicated that extraction by using an ionic liquid has been successfully applied for determination of metals and metal complexes in chia seeds. PMID:26992545

  1. Ionic liquids behave as dilute electrolyte solutions

    PubMed Central

    Gebbie, Matthew A.; Valtiner, Markus; Banquy, Xavier; Fox, Eric T.; Henderson, Wesley A.; Israelachvili, Jacob N.

    2013-01-01

    We combine direct surface force measurements with thermodynamic arguments to demonstrate that pure ionic liquids are expected to behave as dilute weak electrolyte solutions, with typical effective dissociated ion concentrations of less than 0.1% at room temperature. We performed equilibrium force–distance measurements across the common ionic liquid 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([C4mim][NTf2]) using a surface forces apparatus with in situ electrochemical control and quantitatively modeled these measurements using the van der Waals and electrostatic double-layer forces of the Derjaguin–Landau–Verwey–Overbeek theory with an additive repulsive steric (entropic) ion–surface binding force. Our results indicate that ionic liquids screen charged surfaces through the formation of both bound (Stern) and diffuse electric double layers, where the diffuse double layer is comprised of effectively dissociated ionic liquid ions. Additionally, we used the energetics of thermally dissociating ions in a dielectric medium to quantitatively predict the equilibrium for the effective dissociation reaction of [C4mim][NTf2] ions, in excellent agreement with the measured Debye length. Our results clearly demonstrate that, outside of the bound double layer, most of the ions in [C4mim][NTf2] are not effectively dissociated and thus do not contribute to electrostatic screening. We also provide a general, molecular-scale framework for designing ionic liquids with significantly increased dissociated charge densities via judiciously balancing ion pair interactions with bulk dielectric properties. Our results clear up several inconsistencies that have hampered scientific progress in this important area and guide the rational design of unique, high–free-ion density ionic liquids and ionic liquid blends. PMID:23716690

  2. Structure and molecular dynamics of sodium dodecylsulfate micelles modified with hydrophilic short-chain imidazolium salts in aqueous solution.

    PubMed

    Lin, Jia-Hsien; Hou, Sheng-Shu

    2016-07-15

    This study uses pyrene solubilization and NMR experiments to investigate the effects of two hydrophilic short-chain ionic liquids (ILs), 1-ethyl-3-methylimidazolium tetrafluoroborate (EmimBF4) and 1-butyl-3-methylimidazolium tetrafluoroborate (BmimBF4) on the micellization of sodium dodecylsulfate (SDS) in the aqueous phase. The results of the pyrene solubilization experiments indicate that the added short-chain ILs not only promote the micellization of SDS but also modify micelle properties. For NMR studies, the present study focuses on (1) the compositions and spatial arrangements of component molecules and (2) the molecular dynamics of DS(-) in the Rmim-modified SDS micelle. Using pulsed field gradient (PFG) NMR measurements, the composition of the Rmim-modified SDS micelle was calculated by the diffusion data and was found to be correlated with the [SDS]. Two-dimensional nuclear Overhauser effect spectroscopy (2D NOESY) experiments confirm that the 1-alkyl-3-methylimidazolium cation (Rmim(+)) is located inside the Rmim-modified SDS micelle. Corresponding to the microstructure of the Rmim-modified SDS micelle, in terms of (1)H T1 relaxation, the fast motion of SDS α-CH2 and β-CH2 segments are markedly restricted by the attached Rmim(+) to the sulfate group of DS(-), whereas the central carbons and the terminal CH3 group of DS(-) are only slightly affected. The chemical shift analysis indicates that the surface of the Rmim-modified SDS micelle is dehydrated by the absorbed Rmim(+) and becomes more hydrophobic than that of the pure SDS micelle. Insertion of Rmim(+) into the Rmim-modified SDS micelle appears to be driven through the hydrophobic interaction, and it is shown to combine with SDS molecules to constitute the hydrophobic part of the Rmim-modified SDS micelle. PMID:27107206

  3. Ionic liquids as mobile phase additives for the high-performance liquid chromatographic analysis of fluoroquinolone antibiotics in water samples.

    PubMed

    Herrera-Herrera, Antonio V; Hernández-Borges, Javier; Rodríguez-Delgado, Miguel Angel

    2008-12-01

    In this work, four ionic liquids differing in the length of the alkyl chain on the imidazolium cation and one ionic liquid containing tetraethylammonium, all with the same counterion, (i.e. 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIm-BF(4)), 1-butyl-3-methylimidazolium tetrafluoroborate (BMIm-BF(4)), 1-hexyl-3-methylimidazolium tetrafluoroborate (HMIm-BF(4)), 1-methyl-3-octylimidazolium tetrafluoroborate (MOIm-BF(4)), and tetraethylammonium tetrafluroborate (Et(4)N-BF(4))) were tested as mobile phase additives for HPLC separation of a group of seven basic fluoroquinolone (FQ) antibiotics for human and veterinary use (i.e. fleroxacin, ciprofloxacin, lomefloxacin, danofloxacin, enrofloxacin, sarafloxacin, and difloxacin) using a conventional reversed-phase Nova-Pak C(18) column. Fluorescence detection was used. Among the ionic liquids selected, use of BMIm-BF(4) enabled effective separation of these compounds with relatively low analysis time (14 min). The best separation was achieved by isocratic elution at 1 mL min(-1) with 5 mmol L(-1) BMIm-BF(4) and 10 mmol L(-1) ammonium acetate at pH 3.0 with 13% (v/v) acetonitrile. Limits of detection (LODs) for fluorescence detection were in the range 0.5-11 microg L(-1). The method was tested by analyzing several water samples after the optimization of a suitable solid-phase extraction (SPE) procedure using Oasis HLB cartridges. Mean recovery values were above 84% for all analytes with LODs in the range 1-29 ng L(-1). PMID:18854988

  4. Ionic liquid-assisted sonochemical preparation of CeO2 nanoparticles for CO oxidation

    SciTech Connect

    Alammar, Tarek; Noei, Heshmat; Wang, Yuemin; Grünert, Wolfgang; Mudring, Anja -Verena

    2014-10-10

    CeO2 nanoparticles were synthesized via a one-step ultrasound synthesis in different kinds of ionic liquids based on bis(trifluoromethanesulfonylamide, [Tf2N], in combination with various cations including 1-butyl-3-methylimidazolium ([C4mim]+), 1-ethyl-2,3-dimethylimidazolium ([Edimim]+), butyl-pyridinium([Py4]+), 1-butyl-1-methyl-pyrrolidinium ([Pyrr14]+), and 2-hydroxyethyl-trimethylammonium ([N1112OH]+). Depending on synthetic parameters, such as ionic liquid, Ce(IV) precursor, heating method, and precipitator, formed ceria exhibits different morphologies, varying from nanospheres, nanorods, nanoribbons, and nanoflowers. The morphology, crystallinity, and chemical composition of the obtained materials were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), energy dispersive X-ray spectroscopy (EDX), Raman spectroscopy, and N2 adsorption. The structural and electronic properties of the as-prepared CeO2 samples were probed by CO adsorption using IR spectroscopy under ultrahigh vacuum conditions. The catalytic activities of CeO2 nanoparticles were investigated in the oxidation of CO. CeO2 nanospheres obtained sonochemically in [C4mim][Tf2N] exhibit the best performance for low-temperature CO oxidation. As a result, the superior catalytic performance of this material can be related to its mesoporous structure, small particle size, large surface area, and high number of surface oxygen vacancy sites.

  5. Fabrication of hollow mesoporous NiO hexagonal microspheres via hydrothermal process in ionic liquid

    SciTech Connect

    Zhao, Jinbo; Wu, Lili; Zou, Ke

    2011-12-15

    Highlights: Black-Right-Pointing-Pointer Ni(OH){sub 2} precursors were synthesized in ionic liquid and water solution by hydrothermal method. Black-Right-Pointing-Pointer NiO hollow microspheres were prepared by thermal treatment of Ni(OH){sub 2} precursors. Black-Right-Pointing-Pointer NiO hollow microspheres were self-assembled by mesoporous cubic and hexagonal nanocrystals with high specific surface area. Black-Right-Pointing-Pointer The mesoporous structure is stable at 773 K. Black-Right-Pointing-Pointer The ionic liquid absorbed on the O-terminate surface of the crystals to form hydrogen bond and played key roles in determining the final shape of the NiO novel microstructure. -- Abstract: The novel NiO hexagonal hollow microspheres have been successfully prepared by annealing Ni(OH){sub 2}, which was synthesized via an ionic liquid-assisted hydrothermal method. The samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM), transmission electron microscopy (TEM), N{sub 2} adsorption-desorption and Fourier transform infrared spectrometer (FTIR). The results show that the hollow NiO microstructures are self-organized by mesoporous cubic and hexagonal nanocrystals. The mesoporous structure possessed good thermal stability and high specific surface area (ca. 83 m{sup 2}/g). The ionic liquid 1-butyl-3methylimidazolium tetrafluoroborate ([Bmim][BF{sub 4}]) was found to play a key role in controlling the morphology of NiO microstructures during the hydrothermal process. The special hollow mesoporous architectures will have potential applications in many fields, such as catalysts, absorbents, sensors, drug-delivery carriers, acoustic insulators and supercapacitors.

  6. Aqueous Ionic Liquids and Deep Eutectic Solvents for Cellulosic Biomass Pretreatment and Saccharification

    PubMed Central

    Xia, Shuqian; Baker, Gary A.; Li, Hao; Ravula, Sudhir; Zhao, Hua

    2014-01-01

    Ionic liquids (ILs) have proven effective solvents for pretreating lignocellulose, leading to the fast saccharification of cellulose and hemicellulose. However, the high current cost of most ILs remains a major barrier to commercializing this recent approach at a practical scale. As a strategic detour, aqueous solutions of ILs are also being explored as less costly alternatives to neat ILs for cellulose pretreatment. However, limited studies on a few select IL systems are known and there remains no systematic survey of various ILs, eluding an in-depth understanding of pretreatment mechanisms afforded by aqueous IL systems. As a step toward filling this gap, this study presents results for Avicel cellulose pretreatment by neat and aqueous solutions (1.0 and 2.0 M) of 20 different ILs and three deep eutectic solvents, correlating enzymatic hydrolysis rates of pretreated cellulose with various IL properties such as hydrogen-bond basicity, polarity, Hofmeister ranking, and hydrophobicity. The pretreatment efficiencies of neat ILs may be loosely correlated to the hydrogen-bond basicity of the constituent anion and IL polarity; however, the pretreatment efficacies for aqueous ILs are more complicated and cannot be simply related to any single IL property. Several aqueous IL systems have been identified as effective alternatives to neat ILs in lignocellulose pretreatment. In particular, this study reveals that aqueous solutions of 1-butyl-3-methylimidazolium methanesulfonate ([BMIM][MeSO3]) are effective for pretreating switchgrass (Panicum virgatum), resulting in fast saccharification of both cellulose and hemicellulose. An integrated analysis afforded by X-ray diffraction, scanning electron microscopy, thermogravimetric analysis and cellulase adsorption isotherm of lignocellulose samples is further used to deliver a more complete view of the structural changes attending aqueous IL pretreatment. PMID:24729865

  7. Acid-catalyzed dehydration of fructose into 5-hydroxymethylfurfural by cellulose-derived amorphous carbon.

    PubMed

    Qi, Xinhua; Guo, Haixin; Li, Luyang; Smith, Richard L

    2012-11-01

    Carbonaceous solid (CS) catalysts with --SO₃H, --COOH, and phenolic --OH groups were prepared by incomplete hydrothermal carbonization of cellulose followed by either sulfonation with H₂SO₄ to give carbonaceous sulfonated solid (CSS) material or by both chemical activation with KOH and sulfonation to give activated carbonaceous sulfonated solid (a-CSS) material. The obtained carbon products (CS, CSS, and a-CSS) were amorphous; the CSS material had a small surface area (<0.5 m² g⁻¹) and a high --SO₃H group concentration (0.953 mmol g⁻¹), whereas the a-CSS material had a large surface area (514 m²  g ⁻¹) and a low --SO₃H group concentration (0.172 mmol g⁻¹). The prepared materials were evaluated as catalysts for the dehydration of fructose to 5-hydroxymethylfurfural (5-HMF) in the ionic liquid 1-butyl-3-methylimidazolium chloride ([BMIM][Cl]). Remarkably high 5-HMF yields (83 %) could be obtained efficiently (80 °C and 10 min reaction time). CSS and a-CSS catalysts had similar catalytic activities and efficiencies for the conversion of fructose to 5-HMF in [BMIM][Cl]; this could be explained by the trade-off between --SO₃H group concentration (high for CSS) and surface area (high for a-CSS). The cellulose-derived catalysts and ionic liquid exhibited constant activity for five successive recycles, and thus, the methods developed provide a renewable strategy for biomass conversion. PMID:22927099

  8. Use of a 4,5-dicyanoimidazolate anion based ionic liquid for the synthesis of iron and silver nanoparticles.

    PubMed

    Mondal, Suvendu Sekhar; Marquardt, Dorothea; Janiak, Christoph; Holdt, Hans-Jürgen

    2016-04-01

    Sixteen new ionic liquids (ILs) with tetraethylammonium, 1-butyl-3-methylimidazolium, 3-methyl-1-octylimidazolium and tetrabutylphosphonium cations paired with 2-substituted 4,5-dicyanoimidazolate anions (substituent at C2 = methyl, trifluoromethyl, pentafluoroethyl, N,N'-dimethyl amino and nitro) have been synthesized and characterized by using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA). The effects of cation and anion type and structure of the resulting ILs, including several room temperature ionic liquids (RTILs), are reflected in the crystallization, melting points and thermal decomposition of the ILs. ILs exhibited large liquid and crystallization ranges and formed glasses on cooling with glass transition temperatures in the range of -22 to -71 °C. We selected one of the newly designed ILs due to its bigger size, compared to the common conventional IL anion and high electron-withdrawing nitrile group leads to an overall stabilization anion that may stabilize the metal nanoparticles. Stable and better separated iron and silver nanoparticles are obtained by the decomposition of corresponding Fe2(CO)9 and AgPF6, respectively, under N2-atmosphere in newly designed nitrile functionalized 4,5-dicyanoimidazolate anion based IL. Very small and uniform size for Fe-nanoparticles of about 1.8 ± 0.6 nm were achieved without any additional stabilizers or capping molecules. Comparatively bigger size of Ag-nanoparticles was obtained through the reduction of AgPF6 by hydrogen gas. Additionally, the AgPF6 precursor was decomposed under microwave irradiation (MWI), fabricating nut-in-shell-like, that is, core-separated-from-shell Ag-nano-structures. PMID:26885778

  9. Elucidating Interactions and Conductivity of Newly Synthesised Low Bandgap Polymer with Protic and Aprotic Ionic Liquids

    PubMed Central

    Attri, Pankaj; Lee, Seung-Hyun; Hwang, Sun Woo; Kim, Joong I. L.; Lee, Sang Woo; Kwon, Gi-Chung; Choi, Eun Ha; Kim, In Tae

    2013-01-01

    In this paper, we have examined the conductivity and interaction studies of ammonium and imidazolium based ionic liquids (ILs) with the newly synthesised low bandgap polymer (Poly(2-heptadecyl-4-vinylthieno[3,4-d]thiazole) (PHVTT)). Use of low bandgap polymers is the most suitable way to harvest a broader spectrum of solar radiations for solar cells. But, still there is lack of most efficient low bandgap polymer. In order to solve this problem, we have synthesised a new low bandgap polymer and investigated its interaction with the ILs to enhance its conductivity. ILs may undergo almost unlimited structural variations; these structural variations have attracted extensive attention in polymer studies. The aim of present work is to illustrate the state of art progress of implementing the interaction of ILs (protic and aprotic ILs) with newly synthesised low bandgap polymer. In addition to this, our UV-Vis spectroscopy, confocal Raman spectroscopy and FT-IR spectroscopy results have revealed that all studied ILs (tributylmethylammonium methyl sulfate ([N1444][MeSO4] from ammonium family) and 1-methylimidazolium chloride ([Mim]Cl, and 1-butyl-3-methylimidazolium chloride ([Bmim]Cl from imidazolium family) have potential to interact with polymer. Our semi empirical calculation with help of Hyperchem 7 shows that protic IL ([Mim]Cl) interacts strongly with the low bandgap polymer through the H-bonding. Further, protic ILs shows enhanced conductivity than aprotic ILs in association with low bandgap polymer. This study provides the combined effect of low bandgap polymer and ILs that may generate many theoretical and experimental opportunities. PMID:23874829

  10. Structure and dynamics of room temperature ionic liquids with bromide anion: results from 81Br NMR spectroscopy.

    PubMed

    Endo, Takatsugu; Imanari, Mamoru; Hidaka, Yuki; Seki, Hiroko; Nishikawa, Keiko; Sen, Sabyasachi

    2015-05-01

    We report the results of a comprehensive (81)Br NMR spectroscopic study of the structure and dynamics of two room temperature ionic liquids (RTILs), 1-butyl-3-methylimidazolium bromide ([C(4)mim]Br) and 1-butyl-2,3-dimethylimidazolium bromide ([C(4)C(1)mim]Br), in both liquid and crystalline states. NMR parameters in the gas phase are also simulated for stable ion pairs using quantum chemical calculations. The combination of (81)Br spin-lattice and spin-spin relaxation measurements in the motionally narrowed region of the stable liquid state provides information on the correlation time of the translational motion of the cation. (81) Br quadrupolar coupling constants (C(Q)) of the two RTILs were estimated to be 6.22 and 6.52 MHz in the crystalline state which were reduced by nearly 50% in the liquid state, although in the gas phase, the values are higher and span the range of 7-53 MHz depending on ion pair structure. The C(Q) can be correlated with the distance between the cation-anion pairs in all the three states. The (81)Br C(Q) values of the bromide anion in the liquid state indicate the presence of some structural order in these RTILs, the degree of which decreases with increasing temperature. On the other hand, the ionicity of these RTILs is estimated from the combined knowledge of the isotropic chemical shift and the appropriate mean energy of the excited state. [C(4)C(1)mim]Br has higher ionicity than [C(4)mim]Br in the gas phase, while the situation is reverse for the liquid and the crystalline states. PMID:25783567

  11. Solvothermal Synthesis of Three-Dimensional Hierarchical CuS Microspheres from a Cu-Based Ionic Liquid Precursor for High-Performance Asymmetric Supercapacitors.

    PubMed

    Zhang, Jing; Feng, Huijie; Yang, Jiaqin; Qin, Qing; Fan, Hongmin; Wei, Caiying; Zheng, Wenjun

    2015-10-01

    It is meaningful to exploit copper sulfide materials with desired structure as well as potential application due to their cheapness and low toxicity. A low-temperature and facile solvothermal method for preparing three-dimensional (3D) hierarchical covellite (CuS) microspheres from an ionic liquid precursor [Bmim]2Cu2Cl6 (Bmim = 1-butyl-3-methylimidazolium) is reported. The formation of CuS nanostructures was achieved by decomposition of intermediate complex Cu(Tu)3Cl (thiourea = Tu), which produced CuS microspheres with diameters of 2.5-4 μm assembled by nanosheets with thicknesses of 10-15 nm. The ionic liquid, as an "all-in-one" medium, played a key role for the fabrication and self-assembly of CuS nanosheets. The alkylimidazolium rings ([Bmim](+)) were found to adsorb onto the (001) facets of CuS crystals, which inhibited the crystal growth along the [001] direction, while the alkyl chain had influence on the assembly of CuS nanosheets. The CuS microspheres showed enhanced electrochemical performance and high stability for the application in supercapacitors due to intriguing structural design and large specific surface area. When this well-defined CuS electrode was assembled into an asymmetric supercapacitor (ASC) with an activated carbon (AC) electrode, the CuS//AC-ASC demonstrated good cycle performance (∼88% capacitance after 4000 cycles) and high energy density (15.06 W h kg(-1) at a power density of 392.9 W kg(-1)). This work provides new insights into the use of copper sulfide electrode materials for asymmetric supercapacitors and other electrochemical devices. PMID:26371955

  12. Alkali metal ion induced cube shaped mesoporous hematite particles for improved magnetic properties and efficient degradation of water pollutants.

    PubMed

    Roy, Mouni; Naskar, Milan Kanti

    2016-07-27

    Mesoporous cube shaped hematite (α-Fe2O3) particles were prepared using FeCl3 as an Fe(3+) precursor and 1-butyl-3-methylimidazolium bromide (ionic liquid) as a soft template in the presence of different alkali metal (lithium, sodium and potassium) acetates, under hydrothermal conditions at 150 °C/4 h followed by calcination at 350 °C. The formation of the α-Fe2O3 phase in the synthesized samples was confirmed by XRD, FTIR and Raman spectroscopy. Unlike K(+) ions, intercalation of Li(+) and Na(+) ions occurred in α-Fe2O3 crystal layers as evidenced by XRD and Raman spectroscopy. Electron microscopy (FESEM and TEM) images showed the formation of cube-like particles of different sizes in the presence of Li(+), Na(+) and K(+) ions. The mesoporosity of the products was confirmed by N2 adsorption-desorption studies, while their optical properties were analyzed by UV-DRS. Na(+) ion intercalated α-Fe2O3 microcubes showed improved coercivity (5.7 kOe) due to increased strain in crystals, and shape and magnetocrystalline anisotropy. Temperature dependent magnetization of the samples confirmed the existence of Morin temperature in the range of 199-260 K. Catalytic degradation of methylene blue (MB), a toxic water pollutant, was studied using the synthesized products via a heterogeneous photo-Fenton process. The degradation products were traced by electrospray ionization-mass spectrometry (ESI-MS). The α-Fe2O3 microcubes obtained in the presence of Na(+) ions exhibited a more efficient degradation of MB to non-toxic open chain products. PMID:27406648

  13. Isolation and Analysis of Keratins and Keratin-Associated Proteins from Hair and Wool.

    PubMed

    Deb-Choudhury, Santanu; Plowman, Jeffrey E; Harland, Duane P

    2016-01-01

    The presence of highly cross-linked protein networks in hair and wool makes them very difficult substrates for protein extraction, a prerequisite for further protein analysis and characterization. It is therefore imperative that these cross-links formed by disulfide bridges are first disrupted for the efficient extraction of proteins. Chaotropes such as urea are commonly used as efficient extractants. However, a combination of urea and thiourea not only improves recovery of proteins but also results in improved resolution of the keratins in 2DE gels. Reductants also play an important role in protein dissolution. Dithiothreitol effectively removes keratinous material from the cortex, whereas phosphines, like Tris(2-carboxyethyl)phosphine, remove material from the exocuticle. The relative extractability of the keratins and keratin-associated proteins is also dependent on the concentration of chaotropes, reductants, and pH, thus providing a means to preferentially extract these proteins. Ionic liquids such as 1-butyl-3-methylimidazolium chloride (BMIM(+)[Cl](-)) are known to solubilize wool by disrupting noncovalent interactions, specifically intermolecular hydrogen bonds. BMIM(+)[Cl](-) proved to be an effective extractant of wool proteins and complementary in nature to chaotropes such as urea and thiourea for identifying unique peptides of wool proteins using mass spectrometry (MS). Successful identification of proteins resolved by one- or two-dimensional electrophoresis and MS is highly dependent on the optimal recovery of its protease-digested peptides with an efficient removal of interfering substances. The detergent sodium deoxycholate used in conjunction with Empore™ disks improved identification of proteins by mass spectrometry leading to higher percentage sequence coverage, identification of unique peptides and higher score. PMID:26795475

  14. Microstructure of microemulsion modified with ionic liquids in microemulsion electrokinetic chromatography and analysis of seven corticosteroids.

    PubMed

    Ni, Xinjiong; Yu, Meijuan; Cao, Yuhua; Cao, Guangqun

    2013-09-01

    In this work, the influences of ionic liquid (IL) as a modifier on microemulsion microstructure and separation performance in MEEKC were investigated. Experimental results showed that synergetic effect between IL 1-butyl-3-methylimidazolium tetrafluoro-borate (BmimBF4 ) and surfactant SDS gave a decreased CMC. With increment of IL in microemulsion, negative ζ potential of the microdroplets reduced gradually. The influence of IL on the dimensions of microdroplet was complicated. At BmimBF4 less than 8 mM, IL made microemulsion droplet smaller in size. While at BmimBF4 more than 10 mM, the size increased and reached to a maximum value at 12 mM, where the microdroplets were larger than that without IL. After that, the micreodroplet size decreased again. Relative fluorescence intensity of the first vibration band of pyrene to the third one (I1 /I3 ) enhanced as IL was added to microemulsion, which indicated that this addition increased environmental polarity in the inner core of microdroplets. Prednisone, hydrocortisone, prednisolone, hydrocortisone acetate, cortisone acetate, prednisolone acetate, and triamcinolone acetonide were analyzed with MEEKC modified with IL to evaluate the separation performance. Cortisone acetate and prednisolone acetate could not be separated at all in typical microemulsion. The seven analytes could be separated by the addition of 10 mM BmimBF4 into the microemulsion system. The method has been used for analysis of corticosteroids in cosmetic samples with simple extraction; the recoveries for seven analytes were between 86 and 114%. This method provides accuracy, reproducibility, pretreatment simplicity, and could be applied to the quality control of cosmetics. PMID:23801369

  15. Assessment of green cleaning effectiveness on polychrome surfaces by MALDI-TOF mass spectrometry and microscopic imaging.

    PubMed

    Hrdlickova Kuckova, Stepanka; Crhova Krizkova, Michaela; Pereira, Catarina Luísa Cortes; Hynek, Radovan; Lavrova, Olga; Busani, Tito; Branco, Luis Cobra; Sandu, Irina Crina Anca

    2014-08-01

    This article proposes an innovative methodology which employs nondestructive techniques to assess the effectiveness of new formulations based on ionic liquids, as alternative solvents for enzymes (proteases), for the removal of proteinaceous materials from painted surfaces during restoration treatments. Ionic liquids (ILs), also known as "designer" solvents, because of their peculiar properties which can be adjusted by selecting different cation-anion combinations, are potentially green solvents due totheir low vapour pressure. In this study, two ionic liquids were selected: IL1 (1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM][BF4 ])) and IL2 (1-ethyl-3-methylimidazolium ethylsulphate ([EMIM][EtSO4 ])). New formulations were prepared with these ILs and two different proteases (E): one acid (E1-pepsin) and one alkaline (E2-obtained from Aspergillus sojae). These formulations were tested on tempera and oil mock-up samples, prepared in accordance with historically documented recipes, and covered with two different types of protein-based varnishes (egg white and isinglass-fish glue). A noninvasive multiscale imaging methodology was applied before and after the treatment to evaluate the cleaning's effectiveness. Different microscopic techniques-optical microscopy (OM) with visible and fluorescent light, scanning electron microscopy (SEM) and atomic force microscopy (AFM)-together with Matrix-Assisted Laser Desorption/Ionization-Time of Flight Mass Spectrometry (MALDI-TOF MS) were applied on areas cleaned with the new formulations (IL + E) and reference areas cleaned only with the commercial enzyme formulations (gels). MALDI-TOF proved particularly very useful for comparing the diversity and abundance of peptides released by using different enzymatic systems. Microsc. Res. Tech. 77:574-585, 2014. © 2014 Wiley Periodicals, Inc. PMID:24825619

  16. Molecular dynamics simulations of the structure of the graphene-ionic liquid/alkali salt mixtures interface.

    PubMed

    Méndez-Morales, Trinidad; Carrete, Jesús; Pérez-Rodríguez, Martín; Cabeza, Óscar; Gallego, Luis J; Lynden-Bell, Ruth M; Varela, Luis M

    2014-07-14

    We performed molecular dynamics simulations of mixtures of 1-butyl-3-methylimidazolium tetrafluoroborate with lithium tetrafluoroborate and potassium tetrafluoroborate between two charged and uncharged graphene walls, in order to analyze the structure of the well-known formation of layers that takes place on liquids under confinement. For this purpose, we studied the molecular density profiles, free energy profiles for bringing lithium and potassium cations from the bulk mixture to the graphene wall and the orientational distributions of imidazolium rings within the first adsorbed layer as a function of salt concentration and electrode potential. The charge densities in the electrodes were chosen to be zero and ±1 e nm(-2), and the salt molar percentages were %salt = 0, 10 and 25. We found that the layered structure extends up to 1-2 nm, where the bulk behaviour is recovered. In addition, whereas for the neutral surface the layers are composed of both ionic species, increasing the electrode potential, the structure changes to alternating cationic and anionic layers leading to an overcompensation of the charge of the previous layer. We also calculated the distribution of angles of imidazolium rings near neutral and charged graphene walls, finding a limited influence of the added salt. In addition, the average tilt of the imidazolium ring within the first layer goes from 36° with respect to a normal vector to the uncharged graphene wall to 62° in the presence of charged walls. The free energy profiles revealed that lithium and potassium ions are adsorbed on the negative surface only for the highest amount of salt, since the free energy barriers for approaching this electrode are considerably higher than kBT. PMID:24871696

  17. N-(trifluoromethylsulfonyl)aryloxytrifluoromethylsulfoximines [ArO-SO(CF3)=NTf] and N-aryltriflimides Ar-N(Tf)2 by thermal and photolytic dediazoniation of [ArN2][BF4] in [BMIM][Tf2N] ionic liquid: exploiting the ambident nucleophilic character of a "nonnucleophilic" anion.

    PubMed

    Laali, Kenneth K; Okazaki, Takao; Bunge, Scott D

    2007-08-31

    Arenediazonium tetrafluoroborate salts undergo metathesis on immobilization in 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonato)amide [BMIM][Tf(2)N]. The "noncoordinating", "nonnucleophilic" [Tf(2)N] anion acts as an ambident nucleophile toward the aryl cations, formed via thermal dediazoniation, to give predominantly the oxy anion quenching products [ArO-SO(CF(3))=NTf], with minimal formation of ArN(Tf)(2), irrespective of the nature of the substituent(s) on the ArN(2)+. Strong preference for the formation of oxygen trapping products did not change under photolytic conditions, where dediazoniation occurs at room temperature. A minimal amount of the Schiemann product ArF is also formed in both thermal and photolytic dediazoniation, depending on the substituent(s). Progress of dediazoniation in the IL (both thermal and photolytic) and the evolution of the products were directly monitored by (1)H and (19)F NMR. According to DFT (Density Functional Theory) calculations, PhN(Tf)(2) is more stable than PhO-SO(CF(3))=NTf by 15-17 kcal/mol, depending on the basis set. Inclusion of solvation effects (PCM, with acetone and with CH(2)ClCH(2)Cl as solvent) did not change this preference. The [ArN(2)][BF(4)] dediazoniation in [BMIM][Tf(2)N] resulted in synthesis and characterization of a series of hitherto unknown [ArO-SO(CF(3))=NTf] compounds. The X-ray structure of MesO-SO(CF(3))=NTf (Mes = mesityl) is reported. On the basis of extraction studies, suitable solvent systems have been identified that remove the products without dissolving [BMIM][NTf(2)], thus overcoming product recovery difficulties typically associated with the use of this IL. PMID:17665954

  18. Solubility of alkali metal halides in the ionic liquid [C4C1im][OTf].

    PubMed

    Kuzmina, O; Bordes, E; Schmauck, J; Hunt, P A; Hallett, J P; Welton, T

    2016-06-28

    The solubilities of the metal halides LiF, LiCl, LiBr, LiI, NaF, NaCl, NaBr, NaI, KF, KCl, KBr, KI, RbCl, CsCl, CsI, were measured at temperatures ranging from 298.15 to 378.15 K in the ionic liquid 1-butyl-3-methylimidazolium trifluoromethanesulfonate ([C4C1im][OTf]). Li(+), Na(+) and K(+) salts with anions matching the ionic liquid have also been investigated to determine how well these cations dissolve in [C4C1im][OTf]. This study compares the influence of metal cation and halide anion on the solubility of salts within this ionic liquid. The highest solubility found was for iodide salts, and the lowest solubility for the three fluoride salts. There is no outstanding difference in the solubility of salts with matching anions in comparison to halide salts. The experimental data were correlated employing several phase equilibria models, including ideal mixtures, van't Hoff, the λh (Buchowski) equation, the modified Apelblat equation, and the non-random two-liquid model (NRTL). It was found that the van't Hoff model gave the best correlation results. On the basis of the experimental data the thermodynamic dissolution parameters (ΔH, ΔS, and ΔG) were determined for the studied systems together with computed gas phase metathesis parameters. Dissolution depends on the energy difference between enthalpies of fusion and dissolution of the solute salt. This demonstrates that overcoming the lattice energy of the solid matrix is the key to the solubility of inorganic salts in ionic liquids. PMID:27264676

  19. Stabilizing proteins for affinity capillary electrophoresis using ionic liquid aqueous two phase systems: Pharmaceuticals and human serum albumin.

    PubMed

    El-Hady, Deia Abd; Albishri, Hassan M; Rengarajan, Rajesh; El Deeb, Sami; Wätzig, Hermann

    2015-12-01

    Recently, ionic liquids (ILs) are finding ever broader scope within pharmaceutical and bioanalytical applications. In the current work, ACE binding measurements of tryptophan (Try)-HSA, chlorambucil (CHL)-HSA, and dacarbazine (DTIC)-HSA complexes were estimated in the absence or presence of several short chain imidazolium ILs within the range of concentrations of 10.0-1000.0 μmol/L that are far below the critical micelle concentrations of ILs. Results indicated that the value of binding constant of Trp-HSA was dramatically deviated in the presence of 1000.0 μmol/L 1-decyl-3-methylimidazolium bromide (DMIMBr) IL. However, interestingly, there is no any deviation for the Trp-HSA binding constant with 100.0 μmol/L 1-butyl-3-methylimidazolium bromide (BMIMBr) IL as an adjuvant additive in 67.0 mmol/L phosphate buffer at pH 7.4. This finding was further used to estimate the binding constants of important but weakly binding substances of CHL and DTIC antitumors with HSA; their binding constants were also estimated by HPAC giving data in good agreement with that revealed by ACE. These achievements were attributed to the significant improvement of HSA stability by combination with BMIMBr IL through hydrogen bond, electrostatic, and π-π forces. In addition, the use of 100.0 μmol/L BMIMBr extended the stability of native HSA solution stored under the ambient lab conditions up to 25 days with significant improvements in the precision of ACE binding data. PMID:26411263

  20. Physico-Chemical Properties and Phase Behavior of the Ionic Liquid-β-Cyclodextrin Complexes

    PubMed Central

    Rogalski, Marek; Modaressi, Ali; Magri, Pierre; Mutelet, Fabrice; Grydziuszko, Aleksandra; Wlazło, Michał; Domańska, Urszula

    2013-01-01

    The solubility of β-cyclodextrin (β-CD) in ionic liquids (ILs) and the activity coefficients at infinite dilution ( γ13∞) of more than 20 solutes (alkanes, aromatic hydrocarbons, alcohols) were measured in four chosen ionic liquids, their mixtures with β-CD, and in the β-CD at high temperatures from 338 to 398 K using the inverse gas chromatography. The intermolecular interactions, inclusion complexes and the possible increasing of the solubility of β-CD in water using the IL are presented. The solubility of β-CD in ten chosen hydrophobic ILs at the temperature T = 423 K was detected. The solid-liquid phase diagrams (SLE) of {IL (1) + β-CD (2)} binary systems at the high mole fraction of the IL were measured for three systems (1-ethyl-3-methylimidazolium chloride, [EMIM][Cl], 1-ethyl-3-methylimidazolium bromide, [EMIM][Br]; and for 1-butyl-3-methylimidazolium chloride, [BMIM][Cl]). The eutectic points were determined at the high IL concentration for all binary systems. The intermolecular interaction and the possibility of inclusion complexes of the IL and/or solvents with β-CD were discussed. The infrared spectroscopy, IR was used for the description of the intermolecular interactions in the (β-CD + IL) systems. It was shown via the activity coefficients at infinite dilution results that the inclusion complexes are dependent on the temperature. The addition of β-CD to the IL does not improve the selectivity of the separation of the aliphatics from aromatics. PMID:23945559

  1. Thermodynamical and structural properties of binary mixtures of imidazolium chloride ionic liquids and alcohols from molecular simulation

    NASA Astrophysics Data System (ADS)

    Raabe, Gabriele; Köhler, Jürgen

    2008-10-01

    We have performed molecular dynamics simulations to determine the densities, excess energies of mixing, and structural properties of binary mixtures of the 1-alkyl-3-methylimidazolium chloride ionic liquids (ILs) [amim][Cl] and ethanol and 1-propanol in the temperature range from 298.15to363.15K. As in our previous work [J. Chem. Phys. 128, 154509 (2008)], our simulation studies are based on a united atom model from Liu et al. [Phys. Chem. Chem. Phys. 8, 1096 (2006)] for the 1-ethyl- and 1-butyl-3-methylimidazolium cations [emim+] and [bmim+], which we have extended to the 1-hexyl-3-methylimidazolium [hmim+] cation and combined with parameters of Canongia Lopes et al. [J. Phys. Chem. B 108, 2038 (2004)] for the chloride anion [Cl-] and the force field by Khare et al. for the alcohols [J. Phys. Chem. B 108, 10071 (2004)]. With this, we provide both prediction for the densities of the mixtures that have mostly not been investigated experimentally yet and a molecular picture of the interactions between the alcohol molecules and the ions. The negative excess energies of all mixtures indicate an energetically favorable mixing of [amim][Cl] ILs and alcohols. To gain insight into the nonideality of the mixtures on the molecular level, we analyzed their local structures by radial and spatial distribution functions. These analyses show that the local ordering in these mixtures is determined by strong hydrogen-bond interactions between the chloride anion and the hydroxyls of the alcohols, enhanced interactions between the anion and the charged domain of the cation, and an increasing aggregation of the nonpolar alkyl tails of the alcohols and the cations with increasing cation size, which results in a segregation of polar and nonpolar domains.

  2. J-aggregation of ionic liquid solutions of meso-tetrakis(4-sulfonatophenyl)porphyrin

    SciTech Connect

    Ali, Maroof; Kumar, Vinod; Baker, Sheila N; Baker, Gary A; Pandey, Siddharth

    2010-01-01

    The title porphyrin was dissolved in the hydrophilic ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate, [bmim][BF4], and triggered to assemble into J-aggregates by the addition of incremental volumes of water containing various amounts of acid (0.1, 0.2, or 1.0 M HCl). In contrast to recent studies, the current investigation is unique in that it centers on media that contain a predominant ionic liquid component (2.9 5.4 M [bmim][BF4]), as opposed to an aqueous electrolyte containing a small fraction of ionic liquid as dissociated solute. Complex aggregation and underlying photophysical behavior are revealed from absorption spectroscopy, steady-state fluorescence, and resonance light scattering studies. Upon addition of aqueous HCl, the efficient formation of H4TPPS2 J-aggregates from the diprotonated form of meso-tetrakis(4-sulfonatophenyl)porphyrin (H2TPPS4) occurs in [bmim][BF4]-rich media in a manner highly dependent upon the acidity, TPPS concentration, and solvent composition. The unique features of TPPS aggregation in this ionic liquid were elucidated, including the surprising disassembly of J-aggregates at higher aqueous contents, and our results are described qualitatively in terms of the molecular exciton theory. Finally, the potential of this system for the optical sensing of water at a sensitivity below 0.5 wt% is demonstrated. Overall, our findings accentuate how little is known about functional self-assembly within ionic liquids and suggest a number of avenues for exploring this completely untouched research landscape.

  3. Density and Viscosity of Binary Mixtures of Thiocyanate Ionic Liquids + Water as a Function of Temperature.

    PubMed

    Domańska, U; Królikowska, M

    2012-09-01

    Densities and viscosities have been determined for binary mixtures of the ionic liquids (ILs) 1-butyl-3-methylimidazolium thiocyanate [BMIM][SCN], or 1-butyl-4-methylpyridinium thiocyanate [BMPy][SCN], or 1-butyl-1-methylpyrrolidinium thiocyanate [BMPYR][SCN], or 1-butyl-1-methylpiperidinium thiocyanate [BMPIP][SCN] with water over wide range of temperatures (298.15-348.15) K and ambient pressure. The thermal properties of [BMPy][SCN], i.e. glass transition temperature and the heat capacity at glass transition, have been measured using a differential scanning microcalorimetry, DSC. The decomposition of [BMPy][SCN] was detected. The density and viscosity correlations for these systems have been made using an empirical second-order polynomial and by the Vogel-Fulcher-Tammann equation, respectively. The concentration dependences have been described by polynomials. The excess molar volumes and deviations in viscosity have been calculated from the experimental values and were correlated by Redlich-Kister polynomial expansions. The variations of these parameters, with compositions of the mixtures and temperature, have been discussed in terms of molecular interactions. A qualitative analysis of the trend of properties with composition and temperature was performed. Further, the excess partial molar volumes, [Formula: see text] and [Formula: see text], were calculated and discussed. The isobaric expansivities (coefficient of thermal expansion), α, and the excess isobaric expansivities, α(E), were determined for four ILs and their mixtures with water. The results indicate that the interactions of thiocyanate ILs with water is not as strong as with alcohols, which is shown by the positive/slightly negative excess molar volumes in these binary systems. ELECTRONIC SUPPLEMENTARY MATERIAL: The online version of this article (doi:10.1007/s10953-012-9875-7) contains supplementary material, which is available to authorized users. PMID:23002317

  4. Intermolecular vibrations and fast relaxations in supercooled ionic liquids

    NASA Astrophysics Data System (ADS)

    Ribeiro, Mauro C. C.

    2011-06-01

    Short-time dynamics of ionic liquids has been investigated by low-frequency Raman spectroscopy (4 < ω < 100 cm-1) within the supercooled liquid range. Raman spectra are reported for ionic liquids with the same anion, bis(trifluoromethylsulfonyl)imide, and different cations: 1-butyl-3-methylimidazolium, 1-hexyl-3-methylimidazolium, 1-butyl-1-methylpiperidinium, trimethylbutylammonium, and tributylmethylammonium. It is shown that low-frequency Raman spectroscopy provides similar results as optical Kerr effect (OKE) spectroscopy, which has been used to study intermolecular vibrations in ionic liquids. The comparison of ionic liquids containing aromatic and non-aromatic cations identifies the characteristic feature in Raman spectra usually assigned to librational motion of the imidazolium ring. The strength of the fast relaxations (quasi-elastic scattering, QES) and the intermolecular vibrational contribution (boson peak) of ionic liquids with non-aromatic cations are significantly lower than imidazolium ionic liquids. A correlation length assigned to the boson peak vibrations was estimated from the frequency of the maximum of the boson peak and experimental data of sound velocity. The correlation length related to the boson peak (˜19 Å) does not change with the length of the alkyl chain in imidazolium cations, in contrast to the position of the first-sharp diffraction peak observed in neutron and X-ray scattering measurements of ionic liquids. The rate of change of the QES intensity in the supercooled liquid range is compared with data of excess entropy, free volume, and mean-squared displacement recently reported for ionic liquids. The temperature dependence of the QES intensity in ionic liquids illustrates relationships between short-time dynamics and long-time structural relaxation that have been proposed for glass-forming liquids.

  5. Thermoelectric Potential of Polymer-Scaffolded Ionic Liquid Membranes

    NASA Astrophysics Data System (ADS)

    Datta, R. S.; Said, S. M.; Sahamir, S. R.; Karim, M. R.; Sabri, M. F. M.; Nakajo, T.; Kubouchi, M.; Hayashi, K.; Miyazaki, Y.

    2014-06-01

    Organic thin films have been viewed as potential thermoelectric (TE) materials, given their ease of fabrication, flexibility, cost effectiveness, and low thermal conductivity. However, their intrinsically low electrical conductivity is a main drawback which results in a relatively lower TE figure of merit for polymer-based TE materials than for inorganic materials. In this paper, a technique to enhance the ion transport properties of polymers through the introduction of ionic liquids is presented. The polymer is in the form of a nanofiber scaffold produced using the electrospinning technique. These fibers were then soaked in different ionic liquids based on substituted imidazolium such as 1-ethyl-3-methylimidazolium chloride or 1-butyl-3-methylimidazolium bromide. This method was applied to electrospun polyacrylonitrile and a mixture of polyvinyl alcohol and chitosan polymers. The ion transport properties of the membranes have been observed to increase with increasing concentration of ionic liquid, with maximum electrical conductivity of 1.20 × 10-1 S/cm measured at room temperature. Interestingly, the maximum electrical conductivity value surpassed the value of pure ionic liquids. These results indicate that it is possible to significantly improve the electrical conductivity of a polymer membrane through a simple and cost-effective method. This may in turn boost the TE figures of merit of polymer materials, which are well known to be considerably lower than those of inorganic materials. Results in terms of the Seebeck coefficient of the membranes are also presented in this paper to provide an overall representation of the TE potential of the polymer-scaffolded ionic liquid membranes.

  6. Reusable electrochemical sensor for bisphenol A based on ionic liquid functionalized conducting polymer platform.

    PubMed

    Wang, Jhe-Yi; Su, Ya-Ling; Wu, Bo-Hao; Cheng, Shu-Hua

    2016-01-15

    The toxicity of bisphenol A (BPA) has attracted considerable attention, and the reported electrochemical sensors for BPA need further improvement in reusability due to serious surface fouling. In this study, a composite film is designed aiming to provide both an accurate and repeatable platform for BPA determination. The conducting poly(3,4-ethylenedioxythiophene) film (PEDOT) and ionic liquid 1-butyl-3-methylimidazolium bromide (BMIMBr) were modified onto screen-printed carbon electrodes (SPCE) by electropolymerization and drop/spin methods, respectively. The surface characteristics of the composite film were characterized by field emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS) and surface water contact angle experiments. The composite film-modified electrodes exhibited a linear response to BPA in the range of 0.1-500µM in pH 7.0 phosphate buffer solution (PBS) under optimized flow-injection amperometry. The method sensitivity and detection limit (S/N=3) were 0.2661μA μM(-1) (2.419μA μM(-1)cm(-2)) and 0.02µM, respectively. A relative standard deviation of 1.95% was obtained for 77 successive measurements of 10µM BPA, and the repeatability outperformed previously reported work. The proposed method was applied to detect BPA released from plastic water bottles using the standard addition method, and satisfactory recoveries were obtained. The electrochemical assay was validated by comparison with the chromatographic method, and the results showed good agreement between the two methods. PMID:26592583

  7. Modulation of cellulase activity by charged lipid bilayers with different acyl chain properties for efficient hydrolysis of ionic liquid-pretreated cellulose.

    PubMed

    Mihono, Kai; Ohtsu, Takeshi; Ohtani, Mai; Yoshimoto, Makoto; Kamimura, Akio

    2016-10-01

    The stability of cellulase activity in the presence of ionic liquids (ILs) is critical for the enzymatic hydrolysis of insoluble cellulose pretreated with ILs. In this work, cellulase was incorporated in the liposomes composed of negatively charged 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphoglycerol (POPG) and zwitterionic phosphatidylcholines (PCs) with different length and degree of unsaturation of the acyl chains. The liposomal cellulase-catalyzed reaction was performed at 45°C in the acetate buffer solution (pH 4.8) with 2.0g/L CC31 as cellulosic substrate. The crystallinity of CC31 was reduced by treating with 1-butyl-3-methylimidazolium chloride ([Bmim]Cl) at 120°C for 30min. The liposomal cellulase continuously catalyzed hydrolysis of the pretreated CC31 for 48h producing glucose in the presence of 15wt% [Bmim]Cl. The charged lipid membranes were interactive with [Bmim](+), as elucidated by the [Bmim]Cl-induced alterations in fluorescence polarization of the membrane-embedded 1,6-diphenyl-1,3,5-hexatriene (DPH) molecules. The charged membranes offered the microenvironment where inhibitory effects of [Bmim]Cl on the cellulase activity was relieved. The maximum glucose productivity GP of 10.8 mmol-glucose/(hmol-lipid) was obtained at the reaction time of 48h with the cellulase incorporated in the liposomes ([lipid]=5.0mM) composed of 50mol% POPG and 1,2-dilauroyl-sn-glycero-3-phosohocholine (DLPC) with relatively short and saturated acyl chains. PMID:27318965

  8. Ultrasonic-electrodeposition of PtPd alloy nanoparticles on ionic liquid-functionalized graphene paper: towards a flexible and versatile nanohybrid electrode.

    PubMed

    Sun, Yimin; Zheng, Huaming; Wang, Chenxu; Yang, Mengmeng; Zhou, Aijun; Duan, Hongwei

    2016-01-21

    Here we fabricate a new type of flexible and versatile nanohybrid paper electrode by ultrasonic-electrodeposition of PtPd alloy nanoparticles on freestanding ionic liquid (IL)-functionalized graphene paper, and explore its multifunctional applications in electrochemical catalysis and sensing systems. The graphene-based paper materials demonstrate intrinsic flexibility, exceptional mechanical strength and high electrical conductivity, and therefore can serve as an ideal freestanding flexible electrode for electrochemical devices. Furthermore, the functionalization of graphene with IL (i.e., 1-butyl-3-methylimidazolium tetrafluoroborate) not only increases the electroactive surface area of a graphene-based nanohybrid paper electrode, but also improves the adhesion and dispersion of metal nanoparticles on the paper surface. These unique attributes, combined with the merits of an ultrasonic-electrodeposition method, lead to the formation of PtPd alloy nanoparticles on IL-graphene paper with high loading, uniform distribution, controlled morphology and favourable size. Consequently, the resultant nanohybrid paper electrode exhibits remarkable catalytic activity as well as excellent cycle stability and improved anti-poisoning ability towards electrooxidation of fuel molecules such as methanol and ethanol. Furthermore, for nonenzymatic electrochemical sensing of some specific biomarkers such as glucose and reactive oxygen species, the nanohybrid paper electrode shows high selectivity, sensitivity and biocompatibility in these bio-catalytic processes, and can be used for real-time tracking hydrogen peroxide secretion by living human cells. All these features demonstrate its promising application as a versatile nanohybrid electrode material in flexible and lightweight electrochemical energy conversion and biosensing systems such as bendable on-chip power sources, wearable/implantable detectors and in vivo micro-biosensors. PMID:26681401

  9. Effect of ionic liquid on the determination of aromatic amines as contaminants in hair dyes by liquid chromatography coupled to electrochemical detection.

    PubMed

    Lizier, Thiago Mescoloto; Boldrin Zanoni, Maria Valnice

    2012-01-01

    The room temperature ionic liquid (IL) 1-butyl-3-methylimidazolium bis-(trifluorometanesulfonyl)imide BMIm[NTf₂] was used as a novel medium for improvement of separation and quantization of 16 aromatic amines typically present as contaminants in consumer products and detected by HPLC coupled to an electrochemical detector. The aromatic amines, namely 4,4'-diaminodiphenylmethane, 4-chloroaniline, 2-methoxy-5-methyl-aniline, 3,3'-dimethylbenzidine, 2,4-diaminotoluidine, 2-chloro-4-nitroaniline, 4,4'-oxydianiline, aniline, 3,3'-ichlorobenzidine, benzidine, 4-aminobiphenyl, o-dianisidine, o-anisidine, o-toluidine, 4,4'-methylene-bis-2-chloroaniline and 2-naphthylamine are oxidized in methanol/BMIm[NTf₂] at a potential around +0.68V to +0.93V vs. Ag/AgCl at a glassy carbon electrode, which is the base for their determination by HPLC/ED. Using the optimized conditions of methanol/BMIm[NTf₂] 70:30 (v/v) as mobile phase, flow-rate of 0.8 mL·min⁻¹, column CLC-ODS, Eap = +1.0 V and T = 40 °C analytical curves were constructed for each of the tested amines. Good linearity was obtained in the concentration range of 1.09 mg·L⁻¹ to 217 mg·L⁻¹, with excellent correlation coefficients. The limits of detection reached 0.021 mg·L⁻¹ to 0.246 mg·L⁻¹ and good relative standard deviations (RSD, n = 3) were obtained from the measurements. Satisfactory recovery for each aromatic amine was achieved, ranging from 95 to 103%. The developed method was successfully applied to determine six aromatic amines present as contaminants in commercial hair dye samples. PMID:22751261

  10. Liquid infused porous surfaces for mineral fouling mitigation.

    PubMed

    Charpentier, Thibaut V J; Neville, Anne; Baudin, Sophie; Smith, Margaret J; Euvrard, Myriam; Bell, Ashley; Wang, Chun; Barker, Richard

    2015-04-15

    Prevention of mineral fouling, known as scale, is a long-standing problem in a wide variety of industrial applications, such as oil production, water treatment, and many others. The build-up of inorganic scale such as calcium carbonate on surfaces and facilities is undesirable as it can result in safety risks and associated flow assurance issues. To date the overwhelming amount of research has mainly focused on chemical inhibition of scale bulk precipitation and little attention has been paid to deposition onto surfaces. The development of novel more environmentally-friendly strategies to control mineral fouling will most probably necessitate a multifunctional approach including surface engineering. In this study, we demonstrate that liquid infused porous surfaces provide an appealing strategy for surface modification to reduce mineral scale deposition. Microporous polypyrrole (PPy) coatings were fabricated onto stainless steel substrates by electrodeposition in potentiostatic mode. Subsequent infusion of low surface energy lubricants (fluorinated oil Fluorinert FC-70 and ionic liquid 1-Butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (BMIm)) into the porous coatings results in liquid-repellent slippery surfaces. To assess their ability to reduce surface scaling the coatings were subjected to a calcium carbonate scaling environment and the scale on the surface was quantified using Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES). PPy surfaces infused with BMIm (and Fluorinert to a lesser extent) exhibit remarkable antifouling properties with the calcium carbonate deposition reduced by 18 times in comparison to untreated stainless steel. These scaling tests suggest a correlation between the stability of the liquid infused surfaces in artificial brines and fouling reduction efficiency. The current work shows the great potential of such novel coatings for the management of mineral scale fouling. PMID:25585291

  11. High-performance lithium storage in an ultrafine manganese fluoride nanorod anode with enhanced electrochemical activation based on conversion reaction.

    PubMed

    Rui, Kun; Wen, Zhaoyin; Huang, Xiao; Lu, Yan; Jin, Jun; Shen, Chen

    2016-02-01

    A facile, one-step solvothermal reaction route for the preparation of manganese fluoride nanorods is successfully developed using manganese(II) chloride tetrahydrate (MnCl2·4H2O) as the manganese source and the ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate (BmimBF4) as the fluorine source. X-ray diffraction, field-emission scanning electron microscopy and high-resolution transmission electron microscopy (HRTEM) are conducted to characterize the structural and microstructural properties of the synthesized MnF2. The pure-phase tetragonal MnF2 displays nanorod-like morphology with a diameter of about 20 nm and a length of several hundreds of nanometers. The electrochemical performance of the MnF2 nanorod anode for rechargeable lithium batteries is investigated. A reversible discharge capacity as high as 443 mA h g(-1) at 0.1 C is obtained for the lithium uptake reaction with an initial discharge plateau around 0.7 V. The striking enhancement in electrochemical Li storage performance in ultrafine MnF2 nanorods can be attributed to the small diameters of the nanorods and efficient one-dimensional electron transport pathways. Long cycle performance for 2000 cycles at 10 C with a stabilized capacity of about 430 mA h g(-1) after activation is also achieved. Furthermore, lithiated and delithiated MnF2 anodes are analyzed with HRTEM to elucidate the conversion mechanism for the electrochemical reaction of MnF2 nanorods with Li at a microscopic level. PMID:26766389

  12. On-line in-syringe magnetic stirring assisted dispersive liquid-liquid microextraction HPLC--UV method for UV filters determination using 1-hexyl-3-methylimidazolium hexafluorophosphate as extractant.

    PubMed

    Suárez, Ruth; Clavijo, Sabrina; Avivar, Jessica; Cerdà, Víctor

    2016-02-01

    An environmental friendly and fully automated method using in-syringe magnetic stirring assisted dispersive liquid-liquid microextraction coupled with high-performance liquid chromatography has been developed for the determination of UV filters in environmental water samples. The main "green" features on this method are the use of an ionic liquid as extracting solvent, avoiding the use of chlorinated solvents, and the on-line microextraction, preconcentration, separation and detection minimizing the use of reagents and so the waste generation. After sample treatment, 20 µL of the organic droplet was injected onto the HPLC-UV system. Various parameters affecting the extraction efficiency were studied using multivariate optimization approach, including the quantity of extraction and dispersive solvents, extraction and sedimentation time, ionic strength and pH. Under optimized conditions, limits of detection were within the range of 0.08-12 µg/L, for 3.5 mL sample volume. Linearity ranges were up to 500 µg/L for the UV-filters studied. Furthermore, enrichment factors ranging from 11 to 23 folds were obtained. Intra- and inter-assay precisions were 6% and 8%, respectively. Finally, the proposed method was successfully applied to determine UV filters in surface seawater and swimming pool samples attaining satisfactory recoveries over the range of 89-114% and 86-107%, respectively. PMID:26653488

  13. Interaction of ionic liquid with water with variation of water content in 1-butyl-3-methyl-imidazolium hexafluorophosphate ([bmim][PF6])/TX-100/water ternary microemulsions monitored by solvent and rotational relaxation of coumarin 153 and coumarin 490.

    PubMed

    Seth, Debabrata; Chakraborty, Anjan; Setua, Palash; Sarkar, Nilmoni

    2007-06-14

    The interaction of water with room temperature ionic liquid (RTIL) [bmim][PF6] has been studied in [bmim][PF6]/TX-100/water ternary microemulsions by solvent and rotational relaxation of coumarin 153 (C-153) and coumarin 490 (C-490). The rotational relaxation and average solvation time of C-153 and C-490 gradually decrease with increase in water content of the microemulsions. The gradual increase in the size of the microemulsion with increase in w0 (w0=[water]/[surfactant]) is evident from dynamic light scattering measurements. Consequently the mobility of the water molecules also increases. In comparison to pure water the retardation of solvation time in the RTIL containing ternary microemulsions is very less. The authors have also reported the solvation time of C-490 in neat [bmim][PF6]. The solvation time of C-490 in neat [bmim][PF6] is bimodal with time constants of 400 ps and 1.10 ns. PMID:17581068

  14. Interaction of ionic liquid with water with variation of water content in 1-butyl-3-methyl-imidazolium hexafluorophosphate ([bmim][PF6])/TX-100/water ternary microemulsions monitored by solvent and rotational relaxation of coumarin 153 and coumarin 490

    NASA Astrophysics Data System (ADS)

    Seth, Debabrata; Chakraborty, Anjan; Setua, Palash; Sarkar, Nilmoni

    2007-06-01

    The interaction of water with room temperature ionic liquid (RTIL) [bmim][PF6] has been studied in [bmim][PF6]/TX-100/water ternary microemulsions by solvent and rotational relaxation of coumarin 153 (C-153) and coumarin 490 (C-490). The rotational relaxation and average solvation time of C-153 and C-490 gradually decrease with increase in water content of the microemulsions. The gradual increase in the size of the microemulsion with increase in w0 (w0=[water]/[surfactant]) is evident from dynamic light scattering measurements. Consequently the mobility of the water molecules also increases. In comparison to pure water the retardation of solvation time in the RTIL containing ternary microemulsions is very less. The authors have also reported the solvation time of C-490 in neat [bmim][PF6]. The solvation time of C-490 in neat [bmim][PF6] is bimodal with time constants of 400ps and 1.10ns.

  15. Ionic liquid and deep eutectic solvent-activated CelA2 variants generated by directed evolution.

    PubMed

    Lehmann, Christian; Bocola, Marco; Streit, Wolfgang R; Martinez, Ronny; Schwaneberg, Ulrich

    2014-06-01

    Chemoenzymatic cellulose degradation is one of the key steps for the production of biomass-based fuels under mild conditions. An effective cellulose degradation process requires diverse physico-chemical dissolution of the biomass prior to enzymatic degradation. In recent years, "green" solvents, such as ionic liquids and, more recently, deep eutectic liquids, have been proposed as suitable alternatives for biomass dissolution by homogenous catalysis. In this manuscript, a directed evolution campaign of an ionic liquid tolerant β-1,4-endoglucanase (CelA2) was performed in order to increase its performance in the presence of choline chloride/glycerol (ChCl:Gly) or 1-butyl-3-methylimidazolium chloride ([BMIM]Cl), as a first step to identify residues which govern ionic strength resistance and obtaining insights for employing cellulases on the long run in homogenous catalysis of lignocellulose degradation. After mutant library screening, variant M4 (His288Phe, Ser300Arg) was identified, showing a dramatically reduced activity in potassium phosphate buffer and an increased activity in the presence of ChCl:Gly or [BMIM]Cl. Further characterization showed that the CelA2 variant M4 is activated in the presence of these solvents, representing a first report of an engineered enzyme with an ionic strength activity switch. Structural analysis revealed that Arg300 could be a key residue for the ionic strength activation through a salt bridge with the neighboring Asp287. Experimental and computational results suggest that the salt bridge Asp287-Arg300 generates a nearly inactive CelA2 variant and activity is regained when ChCl:Gly or [BMIM]Cl are supplemented (~5-fold increase from 0.64 to 3.37 μM 4-MU/h with the addition ChCl:Gly and ~23-fold increase from 3.84 to 89.21 μM 4-pNP/h with the addition of [BMIM]Cl). Molecular dynamic simulations further suggest that the salt bridge between Asp287 and Arg300 in variant M4 (His288Phe, Ser300Arg) modulates the observed salt

  16. Dielectric relaxation in ionic liquid/dipolar solvent binary mixtures: A semi-molecular theory

    NASA Astrophysics Data System (ADS)

    Daschakraborty, Snehasis; Biswas, Ranjit

    2016-03-01

    A semi-molecular theory is developed here for studying dielectric relaxation (DR) in binary mixtures of ionic liquids (ILs) with common dipolar solvents. Effects of ion translation on DR time scale, and those of ion rotation on conductivity relaxation time scale are explored. Two different models for the theoretical calculations have been considered: (i) separate medium approach, where molecularities of both the IL and dipolar solvent molecules are retained, and (ii) effective medium approach, where the added dipolar solvent molecules are assumed to combine with the dipolar ions of the IL, producing a fictitious effective medium characterized via effective dipole moment, density, and diameter. Semi-molecular expressions for the diffusive DR times have been derived which incorporates the effects of wavenumber dependent orientational static correlations, ion dynamic structure factors, and ion translation. Subsequently, the theory has been applied to the binary mixtures of 1-butyl-3-methylimidazolium tetrafluoroborate ([Bmim][BF4]) with water (H2O), and acetonitrile (CH3CN) for which experimental DR data are available. On comparison, predicted DR time scales show close agreement with the measured DR times at low IL mole fractions (xIL). At higher IL concentrations (xIL > 0.05), the theory over-estimates the relaxation times and increasingly deviates from the measurements with xIL, deviation being the maximum for the neat IL by almost two orders of magnitude. The theory predicts negligible contributions to this deviation from the xIL dependent collective orientational static correlations. The drastic difference between DR time scales for IL/solvent mixtures from theory and experiments arises primarily due to the use of the actual molecular volume ( Vmol dip ) for the rotating dipolar moiety in the present theory and suggests that only a fraction of Vmol dip is involved at high xIL. Expectedly, nice agreement between theory and experiments appears when experimental

  17. The Synthesis of Cellulose Graft Copolymers Using Cu(0)-Mediated Polymerization

    NASA Astrophysics Data System (ADS)

    Donaldson, Jason L.

    Cellulose is the most abundant renewable polymer on the planet and there is great interest in expanding its use beyond its traditional applications. However, its hydrophilicity and insolubility in most common solvent systems are obstacles to its widespread use in advanced materials. One way to counteract this is to attach hydrophobic polymer chains to cellulose: this allows the properties of the copolymer to be tailored by the molecular weight, density, and physical properties of the grafts. Two methods were used here to synthesize the graft copolymers: a 'grafting-from' approach, where synthetic chains were grown outward from bromoester moieties on cellulose (Cell-BiB) via Cu(0)-mediated polymerization; and a 'grafting-to' approach, where fully formed synthetic chains with terminal sulfide functionality were added to cellulose acetate with methacrylate functionality (CA-MAA) via thiol-ene Michael addition. The Cell-BiB was synthesized in the ionic liquid 1-butyl-3-methylimidazolium chloride and had a degree of substitution of 1.13. Polymerization from Cell-BiB proceeded at similar but slightly slower rate than an analogous non-polymeric initiator (EBiB). The average graft density of poly(methyl acrylate) chains was 0.71 chains/ring, with a maximum of 1.0 obtained. The graft density when grafting poly(methyl methacrylate) was only 0.15, and this appeared to be due to the slow initiation of BiB groups. Using EBiB to model the reaction and improve the design should allow this to be overcome. Chain extension experiments demonstrated the living behaviour of the polymer. The CA-MAA was synthesized by esterification with methacrylic acid. Reactions of CA-MAA with thiophenol and dodecanethiol resulted in quantitative addition of the thiol to the alkene. The grafts were synthesized by Cu(0)-mediated polymerization from a bifunctional initiator containing a disulfide bond, followed by reduction to sulfides. The synthetic polymers were successfully grafted to CA-MAA but the

  18. Molecular dynamics simulations of the structure and single-particle dynamics of mixtures of divalent salts and ionic liquids

    SciTech Connect

    Gómez-González, Víctor; Docampo-Álvarez, Borja; Gallego, Luis J.; Varela, Luis M.; Lynden-Bell, Ruth M.

    2015-09-28

    We report a molecular dynamics study of the structure and single-particle dynamics of mixtures of a protic (ethylammonium nitrate) and an aprotic (1-butyl-3-methylimidazolium hexaflurophosphate [BMIM][PF{sub 6}]) room-temperature ionic liquids doped with magnesium and calcium salts with a common anion at 298.15 K and 1 atm. The solvation of these divalent cations in dense ionic environments is analyzed by means of apparent molar volumes of the mixtures, radial distribution functions, and coordination numbers. For the protic mixtures, the effect of salt concentration on the network of hydrogen bonds is also considered. Moreover, single-particle dynamics of the salt cations is studied by means of their velocity autocorrelation functions and vibrational densities of states, explicitly analyzing the influence of salt concentration, and cation charge and mass on these magnitudes. The effect of the valency of the salt cation on these properties is considered comparing the results with those for the corresponding mixtures with lithium salts. We found that the main structural and dynamic features of the local solvation of divalent cations in ionic liquids are similar to those of monovalent salts, with cations being localized in the polar nanoregions of the bulk mixture coordinated in monodentate and bidentate coordination modes by the [NO{sub 3}]{sup −} and [PF{sub 6}]{sup −} anions. However, stronger electrostatic correlations of these polar nanoregions than in mixtures with salts with monovalent cations are found. The vibrational modes of the ionic liquid (IL) are seen to be scarcely affected by the addition of the salt, and the effect of mass and charge on the vibrational densities of states of the dissolved cations is reported. Cation mass is seen to exert a deeper influence than charge on the low-frequency vibrational spectra, giving a red shift of the vibrational modes and a virtual suppression of the higher energy vibrational modes for the heavier Ca{sup 2

  19. Phase behaviour and conductivity of supporting electrolytes in supercritical difluoromethane and 1,1-difluoroethane.

    PubMed

    Han, Xue; Ke, Jie; Suleiman, Norhidayah; Levason, William; Pugh, David; Zhang, Wenjian; Reid, Gillian; Licence, Peter; George, Michael W

    2016-06-01

    We present investigations into a variety of supporting electrolytes and supercritical fluids probing the phase and conductivity behaviour of these systems and show that they not only provide sufficient electrical conductivity for an electrodeposition bath, but match the requirements imposed by the different precursors and process parameters, e.g. increased temperature, for potential deposition experiments. The two supercritical fluids that have been explored in this study are difluoromethane (CH2F2) and 1,1-difluoroethane (CHF2CH3). For CH2F2, the phase behaviour and electrical conductivity of eight ionic compounds have been studied. Each compound consists of a cation and an anion from the selected candidates i.e. tetramethylammonium ([N(CH3)4](+)), tetrabutylammonium ([N((n)C4H9)4](+)), 1-ethyl-3-methylimidazolium ([EMIM](+)) and 1-butyl-3-methylimidazolium ([BMIM](+)) for cations, and tetrakis(perfluoro-tert-butoxy)aluminate ([Al(OC(CF3)3)4](-)), chloride (Cl(-)), trifluoromethyl sulfonimide ([NTf2](-)) and tris(pentafluoroethyl)trifluorophosphate ([FAP](-)) for anions. For CHF2CH3, [N((n)C4H9)4][BF4] and [N((n)C4H9)4][B{3,5-C6H3(CF3)2}4] have been investigated for comparison with the previously measured solubility and conductivity in CH2F2. We have found that [N((n)C4H9)4][Al(OC(CF3)3)4], [N((n)C4H9)4][FAP] and [N(CH3)4][FAP] have much higher molar conductivity in scCH2F2 at similar conditions than [N((n)C4H9)4][BF4], a widely used commercial electrolyte. Additionally, scCHF2CH3 shows potential for use as the solvent for supercritical fluid electrodeposition, especially at high temperatures since high density of this fluid can be achieved at lower operating pressures than similar fluids that can be used to produce electrochemical baths with comparable conductivity. PMID:27166921

  20. Sugarcane bagasse pretreatment using three imidazolium-based ionic liquids; mass balances and enzyme kinetics

    PubMed Central

    2012-01-01

    Background Effective pretreatment is key to achieving high enzymatic saccharification efficiency in processing lignocellulosic biomass to fermentable sugars, biofuels and value-added products. Ionic liquids (ILs), still relatively new class of solvents, are attractive for biomass pretreatment because some demonstrate the rare ability to dissolve all components of lignocellulosic biomass including highly ordered (crystalline) cellulose. In the present study, three ILs, 1-butyl-3-methylimidazolium chloride ([C4mim]Cl), 1-ethyl-3-methylimidazolium chloride ([C2mim]Cl), 1-ethyl-3-methylimidazolium acetate ([C2mim]OAc) are used to dissolve/pretreat and fractionate sugarcane bagasse. In these IL-based pretreatments the biomass is completely or partially dissolved in ILs at temperatures greater than 130°C and then precipitated by the addition of an antisolvent to the IL biomass mixture. For the first time mass balances of IL-based pretreatments are reported. Such mass balances, along with kinetics data, can be used in process modelling and design. Results Lignin removals of 10% mass of lignin in bagasse with [C4mim]Cl, 50% mass with [C2mim]Cl and 60% mass with [C2mim]OAc, are achieved by limiting the amount of water added as antisolvent to 0.5 water:IL mass ratio thus minimising lignin precipitation. Enzyme saccharification (24 h, 15FPU) yields (% cellulose mass in starting bagasse) from the recovered solids rank as: [C2mim]OAc(83%) > >[C2mim]Cl(53%) = [C4mim]Cl(53%). Composition of [C2mim]OAc-treated solids such as low lignin, low acetyl group content and preservation of arabinosyl groups are characteristic of aqueous alkali pretreatments while those of chloride IL-treated solids resemble aqueous acid pretreatments. All ILs are fully recovered after use (100% mass as determined by ion chromatography). Conclusions In all three ILs regulated addition of water as an antisolvent effected a polysaccharide enriched precipitate since some of the lignin remained dissolved

  1. Synthesis, structural characterization, and reactivity studies of 5-CF3SO3-B10H13.

    PubMed

    Berkeley, Emily R; Ewing, William C; Carroll, Patrick J; Sneddon, Larry G

    2014-05-19

    In contrast to previous reactions carried out in cyclopentane solvent at room temperature that produced 6-TfO-B10H13 (TfO = CF3SO3), the reaction of closo-B10H10(2-) with a large excess of trifluoromethanesulfonic acid in the ionic liquid 1-butyl-3-methylimidazolium trifluoromethanesulfonate (bmimOTf) gave exclusively the previously unknown 5-TfO-B10H13 isomer. Experimental and computational studies demonstrated that the difference in the products of the two reactions is a result of 6-TfO-B10H13 isomerizing to 5-TfO-B10H13 above room temperature in bmimOTf solutions. Reactivity studies showed that 5-TfO-B10H13: (1) is deprotonated by reaction with 1,8-bis(dimethylamino)naphthalene to form the 5-TfO-B10H12(1-) anion; (2) reacts with alcohols to produce 6-RO-B10H13 boryl ethers (R = Me and 4-CH3O-C6H4); (3) undergoes olefin-hydroboration reactions to form 5-TfO-6,9-R2-B10H11 derivatives; and (4) forms a 5-TfO-6,9-(Me2S)2-B10H11 adduct at its Lewis acidic 6,9-borons upon reaction with dimethylsulfide. The 5-TfO-6,9-(Me2S)2-B10H11 adduct was also found to undergo alkyne-insertion reactions to form a range of previously unreported triflate-substituted 4-TfO-ortho-carboranes (1-R-4-TfO-1,2-C2B10H10) and reactions with triethylamine or ammonia to form the first TfO-substituted decaborate [R3NH(+)]2[2-TfO-B10H9(2-)], and [R3NH(+)]2[1-TfO-B10H9(2-)] (R = H, Et) salts. PMID:24785404

  2. Energy efficient microwave synthesis of mesoporous Ce0.5M0.5O2 (Ti, Zr, Hf) nanoparticles for low temperature CO oxidation in an ionic liquid – a comparative study

    SciTech Connect

    Alammar, Tarek; Chow, Ying -Kit; Mudring, Anja -Verena

    2014-11-19

    Ce0.5M0.5O2 (M = Ti, Zr, Hf) nanoparticles have been successfully synthesized by microwave irradiation in the ionic liquid [C4mim][Tf2N] (1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)amide). The morphology, crystallinity, and chemical composition of the obtained materials were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDX), Raman spectroscopy, and N2–adsorption measurements. XRD and Raman spectroscopy analyses confirmed the formation of solid solutions with cubic fluorite structure. The catalytic activities of the Ce0.5M0.5O2 (M = Ti, Zr, Hf) nanoparticles were investigated in the low-temperature oxidation of CO. Ce0.5Zr0.5O2 nanospheres exhibit the best performance (100% conversion at 350 °C), followed by Ce0.5Hf0.5O2 (55% conversion at 360 °C) and Ce0.5Ti0.5O2 (11% conversion at 350 °C). Heating the as-prepared Ce0.5Zr0.5O2 to 600 °C for extended time leads to a decrease in surface area and, as expected decreased catalytic activity. Depending on the ionic liquid the obtained Ce0.5Zr0.5O2 exhibits different morphologies, varying from nano-spheres in [C4mim][Tf2N] and [P66614][Tf2N] (P66614 = trishexyltetradecylphosphonium) to sheet-like assemblies in [C3mimOH][Tf2N] (C3mimOH = 1-(3-hydroxypropyl)-3-methylimidazolium). As a result, the microwave synthesis superiority to other heating methods like sonochemical synthesis and conventional heating was proven by comparative experiments where the catalytic activity of Ce0.5Zr0.5O2 obtained by alternate methods such as conventional heating was found to

  3. Cellulosic fibers and nonwovens from solutions: Processing and properties

    NASA Astrophysics Data System (ADS)

    Dahiya, Atul

    Cellulose is a renewable and bio-based material source extracted from wood that has the potential to generate value added products such as composites, fibers, and nonwoven textiles. This research was focused on the potential of cellulose as the raw material for fiber spinning and melt blowing of nonwovens. The cellulose was dissolved in two different benign solvents: the amine oxide 4-N-methyl morpholine oxide monohydrate (NMMO•H2O) (lyocell process); and the ionic liquid (IL) 1-butyl-3-methylimidazolium chloride ([C 4MIM]Cl). The solvents have essentially no vapor pressure and are biologically degradable, making them environmentally advantageous for manufacturing processes. The objectives of this research were to: (1) characterize solutions of NMMO and [C4MIM]Cl; (2) develop processing techniques to melt blow nonwoven webs from cellulose using NMMO as a solvent; (3) electrospin cellulosic fibers from the [C4MIM]Cl solvent; (4) spin cellulosic single fibers from the [C4MIM]Cl solvent. Different concentration solutions of cellulose in NMMO and [C4MIM]Cl were initially characterized rheologically and thermally to understand their behavior under different conditions of stress, strain, and temperature. Results were used to determine processing conditions and concentrations for the melt blowing, fiber spinning, and electrospinning experiments. The cellulosic nonwoven webs and fibers were characterized for their physical and optical properties such as tensile strength, water absorbency, fiber diameter, and fiber surface. Thermal properties were also measured by thermogravimetric analysis, differential scanning calorimetry, and dynamic mechanical analysis. Lyocell webs were successfully melt blown from the 14% cellulose solution. Basis weights of the webs were 27, 79, and 141 g/m2 and thicknesses ranged from 0.3-0.9 mm, depending on die temperatures and die to collector distance. The average fiber diameter achieved was 2.3 microns. The 6% lyocell solutions exhibited

  4. Solvatochromic probe response within ionic liquids and their equimolar mixtures with tetraethylene glycol.

    PubMed

    Rai, Rewa; Pandey, Siddharth

    2014-09-25

    Synergism in a probe response within a mixture hints at the presence of strong interactions involving the solvent constituents of the mixture and possibly the probe. Unusual and rare "hyperpolarity" resulting from the synergism in probe response exhibited by ionic liquid (IL) mixtures with glycol family solvents is investigated in detail for equimolar mixtures of tetraethylene glycol (TEG) with many structurally different ILs using several UV-vis absorbance and fluorescence solvatochromic probes. Thirteen different ILs, of the same cation 1-butyl-3-methylimidazolium and different anions, of the same anion bis(trifluoromethylsulfonyl)imide and different cations, and of C2 methyl-substituted imidazolium cations, are used to assess the structural dependence of the IL on synergism exhibited by (IL + TEG) mixture. Responses from UV-vis absorbance probes are used to obtain ET [dipolarity/polarizability and/or H-bond donating (HBD) acidity] and Kamlet-Taft parameters [π* (dipolarity/polarizability), α (HBD acidity), and β (HB accepting basicity)] within (IL + TEG) mixtures. The band I-to-band III fluorescence intensity ratio of dipolarity probe pyrene along with the lowest energy fluorescence band maxima of pyrene-1-carboxaldehyde (PyCHO, a probe for the permittivity of the medium), coumarin-153 and N,N-dimethyl-6-propionyl-2-naphthylamine PRODAN (neutral photoinduced charge-transfer fluorescence probes), and 6-p-toluidine-2-naphthalenesulfonic acid (TNS) and l-anilinonaphthalene-8-sulfonate (ANS) (ionic photoinduced charge-transfer fluorescence probes) are used to assess whether synergism is exhibited by (IL + TEG) equimolar mixtures. Probe responses within TEG equimolar mixtures with ILs are compared to those with common organic solvents. An attempt is made to establish a correlation between the synergism observed in the probe response within an (IL + TEG) mixture and the structural features of the cation and anion of the IL, such as acidity of the protons of the

  5. Water-free rare-earth-metal ionic liquids/ionic liquid crystals based on hexanitratolanthanate(III) anion.

    PubMed

    Ji, Shun-Ping; Tang, Meng; He, Ling; Tao, Guo-Hong

    2013-04-01

    The hexanitratolanthanate anion (La(NO(3))(6)(3-)) is an interesting symmetric anion suitable to construct the component of water-free rare-earth-metal ionic liquids. The syntheses and structural characterization of eleven lanthanum nitrate complexes, [C(n)mim](3)[La(NO(3))(6)] (n=1, 2, 4, 6, 8, 12, 14, 16, 18), including 1,3-dimethylimidazolium hexanitratolanthanate ([C(1)mim](3)[La(NO(3))(6)], 1), 1-ethyl-3-methylimidazolium hexanitratolanthanate ([C(2)mim](3)[La(NO(3))(6)], 2), 1-butyl-3-methylimidazolium hexanitratolanthanate ([C(4)mim](3)[La(NO(3))(6)], 3), 1-isobutyl-3-methylimidazolium hexanetratolanthanate ([isoC(4)mim](3)[La(NO(3))(6)], 4), 1-methyl-3-(3'-methylbutyl)imidazolium hexanitratolanthanate ([MC(4)mim](3)[La(NO(3))(6)], 5), 1-hexyl-3-methylimidazolium hexanitratolanthanate ([C(6)mim](3)[La(NO(3))(6)], 6), 1-methyl-3-octylimidazolium hexanitratolanthanate ([C(8)mim](3)[La(NO(3))(6)], 7), 1-dodecyl-3-methylimidazolium hexanitratolanthanate ([C(12)mim](3)[La(NO(3))(6)], 8), 1-methyl-3-tetradecylimidazolium hexanitratolanthanate ([C(14)mim](3)[La-(NO(3))(6)], 9), 1-hexadecyl-3-methylimid-azolium hexanitratolanthanum ([C(16)dmim](3)[La(NO(3))(6)], 10), and 1-methyl-3-octadecylimidazolium hexanitratolanthanate ([C(18)mim](3)[La(NO(3))(6)], 11) are reported. All new compounds were characterized by (1)H and (13)C NMR, and IR spectroscopy as well as elemental analysis. The crystal structure of compound 1 was determined by using single-crystal X-ray diffraction, giving the following crystallographic information: monoclinic; P2(1)/c; a=15.3170 (3), b=14.2340 (2), c=13.8954(2) Å; β=94.3453(15)°, V=3020.80(9) Å(3), Z=4, ρ=1.764 g cm(-3). The coordination polyhedron around the lanthanum ion is rationalized by six nitrate anions with twelve oxygen atoms. No hydrogen-bonding network or water molecule was found in 1. The thermodynamic stability of the new complexes was investigated by using thermogravimetric analysis (TGA). The water

  6. High-flux Thin-film Nanofibrous Composite Ultrafiltration Membranes Containing Cellulose Barrier Layer

    SciTech Connect

    Ma, H.; Yoon, K; Rong, L; Mao, Y; Mo, Z; Fang, D; Hollander, Z; Gaiteri, J; Hsiao , B; Chu, B

    2010-01-01

    A novel class of thin-film nanofibrous composite (TFNC) membrane consisting of a cellulose barrier layer, a nanofibrous mid-layer scaffold, and a melt-blown non-woven substrate was successfully fabricated and tested as an ultrafiltration (UF) filter to separate an emulsified oil and water mixture, a model bilge water for on-board ship bilge water purification. Two ionic liquids: 1-butyl-3-methylimidazolium chloride and 1-ethyl-3-methylimidazolium acetate, were chosen as the solvent to dissolve cellulose under mild conditions. The regenerated cellulose barrier layer exhibited less crystallinity (determined by wide-angle X-ray diffraction, WAXD) than the original cotton linter pulps, but good thermal stability (determined by thermal gravimetric analysis, TGA). The morphology, water permeation, and mechanical stability of the chosen TFNCmembranes were thoroughly investigated. The results indicated that the polyacrylonitrile (PAN) nanofibrous scaffold was partially imbedded in the cellulose barrier layer, which enhanced the mechanical strength of the top barrier layer. The permeation flux of the cellulose-based TFNCmembrane was significantly higher (e.g. 10x) than comparable commercial UFmembranes (PAN10 and PAN400, Sepro) with similar rejection ratios for separation of oil/water emulsions. The molecular weight cut-off (MWCO) of TFNC membranes with cellulose barrier layer was evaluated using dextran feed solutions. The rejection was found to be higher than 90% with a dextran molecular weight of 2000 KDa, implying that the nominal pore size of the membrane was less than 50 nm. High permeation flux was also observed in the filtration of an emulsified oil/water mixture as well as of a sodium alginate aqueous solution, while high rejection ratio (above 99.5%) was maintained after prolonged operation. A variation of the barrier layer thickness could dramatically affect the permeation flux and the rejection ratio of the TFNCmembranes, while different sources of cellulose

  7. Molecular dynamics simulations of the structure and single-particle dynamics of mixtures of divalent salts and ionic liquids

    NASA Astrophysics Data System (ADS)

    Gómez-González, Víctor; Docampo-Álvarez, Borja; Cabeza, Oscar; Fedorov, Maxim; Lynden-Bell, Ruth M.; Gallego, Luis J.; Varela, Luis M.

    2015-09-01

    We report a molecular dynamics study of the structure and single-particle dynamics of mixtures of a protic (ethylammonium nitrate) and an aprotic (1-butyl-3-methylimidazolium hexaflurophosphate [BMIM][PF6]) room-temperature ionic liquids doped with magnesium and calcium salts with a common anion at 298.15 K and 1 atm. The solvation of these divalent cations in dense ionic environments is analyzed by means of apparent molar volumes of the mixtures, radial distribution functions, and coordination numbers. For the protic mixtures, the effect of salt concentration on the network of hydrogen bonds is also considered. Moreover, single-particle dynamics of the salt cations is studied by means of their velocity autocorrelation functions and vibrational densities of states, explicitly analyzing the influence of salt concentration, and cation charge and mass on these magnitudes. The effect of the valency of the salt cation on these properties is considered comparing the results with those for the corresponding mixtures with lithium salts. We found that the main structural and dynamic features of the local solvation of divalent cations in ionic liquids are similar to those of monovalent salts, with cations being localized in the polar nanoregions of the bulk mixture coordinated in monodentate and bidentate coordination modes by the [NO3]- and [PF6]- anions. However, stronger electrostatic correlations of these polar nanoregions than in mixtures with salts with monovalent cations are found. The vibrational modes of the ionic liquid (IL) are seen to be scarcely affected by the addition of the salt, and the effect of mass and charge on the vibrational densities of states of the dissolved cations is reported. Cation mass is seen to exert a deeper influence than charge on the low-frequency vibrational spectra, giving a red shift of the vibrational modes and a virtual suppression of the higher energy vibrational modes for the heavier Ca2+ cations. No qualitative difference with

  8. Electrochemistry of Iodide, Iodine, and Iodine Monochloride in Chloride Containing Nonhaloaluminate Ionic Liquids.

    PubMed

    Bentley, Cameron L; Bond, Alan M; Hollenkamp, Anthony F; Mahon, Peter J; Zhang, Jie

    2016-02-01

    The electrochemical behavior of iodine remains a contemporary research interest due to the integral role of the I(-)/I3(-) couple in dye-sensitized solar cell technology. The neutral (I2) and positive (I(+)) oxidation states of iodine are known to be strongly electrophilic, and thus the I(-)/I2/I(+) redox processes are sensitive to the presence of nucleophilic chloride or bromide, which are both commonly present as impurities in nonhaloaluminate room temperature ionic liquids (ILs). In this study, the electrochemistry of I(-), I2, and ICl has been investigated by cyclic voltammetry at a platinum macrodisk electrode in a binary IL mixture composed of 1-butyl-3-methylimidazolium chloride ([C4mim]Cl) and 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([C2mim][NTf2]). In the absence of chloride (e.g., in neat [C2mim][NTf2]), I(-) is oxidized in an overall one electron per iodide ion process to I2 via an I3(-) intermediate, giving rise to two resolved I(-)/I3(-) and I3(-)/I2 processes, as per previous reports. In the presence of low concentrations of chloride ([Cl(-)] and [I(-)] are both <30 mM), an additional oxidation process appears at potentials less positive than the I3(-)/I2 process, which corresponds to the oxidation of I3(-) to the interhalide complex anion [ICl2](-), in an overall two electron per iodide ion process. In the presence of a large excess of Cl(-) ([I(-)] ≈ 10 mM and [Cl(-)] ≈ 3.7 M), I(-) is oxidized in an overall two electron per iodide ion process to [ICl2](-) via an [I2Cl](-) intermediate (confirmed by investigating the voltammetric response of ICl and I2 under these conditions). In summary, the I(-)/I2/I(+) processes in nonhaloaluminate ILs involve a complicated interplay between multiple electron transfer pathways and homogeneous chemical reactions which may not be at equilibrium on the voltammetric time scale. PMID:26708364

  9. A counter-charge layer in generalized solvents framework for electrical double layers in neat and hybrid ionic liquid electrolytes

    SciTech Connect

    Huang, Jingsong; Feng, Guang; Sumpter, Bobby G; Qiao, Rui; Meunier, Vincent

    2011-01-01

    Room-temperature ionic liquids (RTILs) have received significant attention as electrolytes due to a number of attractive properties such as their wide electrochemical windows. Since electrical double layers (EDLs) are the cornerstone for the applications of RTILs in electrochemical systems such as supercapacitors, it is important to develop an understanding of the structure capacitance relationships for these systems. Here we present a theoretical framework termed counter-charge layer in generalized solvents (CGS) for describing the structure and capacitance of the EDLs in neat RTILs and in RTILs mixed with different mass fractions of organic solvents. Within this framework, an EDL is made up of a counter-charge layer exactly balancing the electrode charge, and of polarized generalized solvents (in the form of layers of ion pairs, each of which has a zero net charge but has a dipole moment the ion pairs thus can be considered as a generalized solvent) consisting of all RTILs inside the system except the counter-ions in the counter-charge layer, together with solvent molecules if present. Several key features of the EDLs that originate from the strong ion ion correlation in RTILs, e.g., overscreening of electrode charge and alternating layering of counter-ions and co-ions, are explicitly incorporated into this framework. We show that the dielectric screening in EDLs is governed predominately by the polarization of generalized solvents (or ion pairs) in the EDL, and the capacitance of an EDL can be related to its microstructure with few a priori assumptions or simplifications. We use this framework to understand two interesting phenomena observed in molecular dynamics simulations of EDLs in a neat IL of 1-butyl-3- methylimidazolium tetrafluoroborate ([BMIM][BF4]) and in a mixture of [BMIM][BF4] and acetonitrile (ACN): (1) the capacitance of the EDLs in the [BMIM][BF4]/ACN mixture increases only slightly when the mass fraction of ACN in the mixture increases from zero

  10. Hydrothermal synthesis, crystal structure, and catalytic potential of a one-dimensional molybdenum oxide/bipyridinedicarboxylate hybrid.

    PubMed

    Amarante, Tatiana R; Neves, Patrícia; Valente, Anabela A; Paz, Filipe A Almeida; Fitch, Andrew N; Pillinger, Martyn; Gonçalves, Isabel S

    2013-04-15

    The reaction of MoO3, 2,2'-bipyridine-5,5-dicarboxylic acid (H2bpdc), water, and dimethylformamide in the mole ratio 1:1:1730:130 at 150 °C for 3 days in a rotating Teflon-lined digestion bomb leads to the isolation of the molybdenum oxide/bipyridinedicarboxylate hybrid material (DMA)[MoO3(Hbpdc)]·nH2O (1) (DMA = dimethylammonium). Compound 1 was characterized by scanning electron microscopy, FT-IR and (13)C{(1)H} CP MAS NMR spectroscopies, and elemental and thermogravimetric analyses. The solid state structure of 1 was solved and refined through Rietveld analysis of high resolution synchrotron X-ray powder diffraction data in conjunction with information derived from the above techniques. The material, crystallizing in the noncentrosymmetric monoclinic space group Pc, is composed of an anionic one-dimensional organic-inorganic hybrid polymer, ∞(1)[MoO3(Hbpdc)](-), formed by corner-sharing distorted {MoO4N2} octahedra, which cocrystallizes with charge-balancing DMA(+) cations and one water molecule per metal center. In the crystal structure of 1, the close packing of individual anionic polymers, DMA(+) cations, and water molecules is mediated by a series of supramolecular contacts, namely strong (O-H···O, N(+)-H···O(-)) and weak (C-H···O) hydrogen bonding interactions, and π-π contacts involving adjacent coordinated Hbpdc(-) ligands. The catalytic potential of 1 was investigated in the epoxidation reactions of the bioderived olefins methyl oleate (Ole) and DL-limonene (Lim) using tert-butylhydroperoxide (TBHP) as the oxygen donor and 1,2-dichloroethane (DCE) or (trifluoromethyl)benzene (BTF) as cosolvent, at 55 or 75 °C. Under these conditions, 1 acts as a source of active soluble species, leading to epoxide yields of up to 98% for methyl 9,10-epoxystearate (BTF, 75 °C, 100% conversion of Ole) and 89% for 1,2-epoxy-p-menth-8-ene (DCE, 55 °C, 95% conversion of Lim). Catalytic systems employing the ionic liquid 1-butyl-3-methylimidazolium bis

  11. Simultaneous determination of acrylamide, asparagine and glucose in food using short chain methyl imidazolium ionic liquid based ultrasonic assisted extraction coupled with analyte focusing by ionic liquid micelle collapse capillary electrophoresis.

    PubMed

    Abd El-Hady, Deia; Albishri, Hassan M

    2015-12-01

    Acrylamide (AA) is a known lethal neurotoxin and carcinogen. AA is formed in foods during the browning process by the Maillard reaction of glucose (GL) with asparagine (AS). For the first time, the simultaneous online preconcentration and separation of AA, AS and GL using analyte focusing by ionic liquid micelle collapse capillary electrophoresis (AFILMC) was presented. Samples were prepared in a 1-butyl-3-methylimidazolium bromide (BMIMBr) micellar matrix with a conductivity 4 times greater than that of the running buffer (12.5 mmol L(-1) phosphate buffer at pH 8.5). Samples were hydrodynamically injected into a fused silica capillary at 25.0 mbar for 25.0 s. Separations were performed by applying a voltage of 25.0 kV and a detection at 200.0 nm. To sufficiently reduce BMIMBr adsorption on the interior surface of capillary, an appropriate rinsing procedure by hydrochloric acid and water was optimized. AFILMC measurements of analytes within the concentration range of 0.05-10.0 μmol L(-1) achieved adequate reproducibility and accuracy with RSD 1.14-3.42% (n=15) and recovery 98.0-110.0%, respectively. Limits of detections were 0.71 ng g(-1) AA, 1.06 ng g(-1) AS and 27.02 ng g(-1) GL with linearity ranged between 2.2 and 1800 ng g(-1). The coupling of AFILMC with IL based ultrasonic assisted extraction (ILUAE) was successfully applied to the efficient extraction and determination of AA, AS and GL in bread samples. The structure of ILs has significant effects on the extraction efficiency of analytes. The optimal extraction efficiency (97.8%) was achieved by an aqueous extraction with 4:14 ratio of sample: 3.0 mol L(-1) BMIMBr followed by sonication at 35 °C. The proposed combination of ILUAE and AFILMC was simple, ecofriendly, reliable and inexpensive to analyze a toxic compound and its precursors in bread which is applicable to food safety. PMID:26041230

  12. Molecular dynamics simulations of the structure and single-particle dynamics of mixtures of divalent salts and ionic liquids.

    PubMed

    Gómez-González, Víctor; Docampo-Álvarez, Borja; Cabeza, Oscar; Fedorov, Maxim; Lynden-Bell, Ruth M; Gallego, Luis J; Varela, Luis M

    2015-09-28

    We report a molecular dynamics study of the structure and single-particle dynamics of mixtures of a protic (ethylammonium nitrate) and an aprotic (1-butyl-3-methylimidazolium hexaflurophosphate [BMIM][PF6]) room-temperature ionic liquids doped with magnesium and calcium salts with a common anion at 298.15 K and 1 atm. The solvation of these divalent cations in dense ionic environments is analyzed by means of apparent molar volumes of the mixtures, radial distribution functions, and coordination numbers. For the protic mixtures, the effect of salt concentration on the network of hydrogen bonds is also considered. Moreover, single-particle dynamics of the salt cations is studied by means of their velocity autocorrelation functions and vibrational densities of states, explicitly analyzing the influence of salt concentration, and cation charge and mass on these magnitudes. The effect of the valency of the salt cation on these properties is considered comparing the results with those for the corresponding mixtures with lithium salts. We found that the main structural and dynamic features of the local solvation of divalent cations in ionic liquids are similar to those of monovalent salts, with cations being localized in the polar nanoregions of the bulk mixture coordinated in monodentate and bidentate coordination modes by the [NO3](-) and [PF6](-) anions. However, stronger electrostatic correlations of these polar nanoregions than in mixtures with salts with monovalent cations are found. The vibrational modes of the ionic liquid (IL) are seen to be scarcely affected by the addition of the salt, and the effect of mass and charge on the vibrational densities of states of the dissolved cations is reported. Cation mass is seen to exert a deeper influence than charge on the low-frequency vibrational spectra, giving a red shift of the vibrational modes and a virtual suppression of the higher energy vibrational modes for the heavier Ca(2+) cations. No qualitative

  13. Regenerating cellulose from ionic liquids for an accelerated enzymatic hydrolysis

    SciTech Connect

    Zhao, Hua; Jones, Cecil L; Baker, Gary A; Xia, Shuqian; Olubajo, Olarongbe; Person, Vernecia

    2009-01-01

    The efficient conversion of lignocellulosic materials into fuel ethanol has become a research priority in producing affordable and renewable energy. The pretreatment of lignocelluloses is known to be key to the fast enzymatic hydrolysis of cellulose. Recently, certain ionic liquids (ILs)were found capable of dissolving more than 10 wt% cellulose. Preliminary investigations [Dadi, A.P., Varanasi, S., Schall, C.A., 2006. Enhancement of cellulose saccharification kinetics using an ionic liquid pretreatment step. Biotechnol. Bioeng. 95, 904 910; Liu, L., Chen, H., 2006. Enzymatic hydrolysis of cellulose materials treated with ionic liquid [BMIM]Cl. Chin. Sci. Bull. 51, 2432 2436; Dadi, A.P., Schall, C.A., Varanasi, S., 2007. Mitigation of cellulose recalcitrance to enzymatic hydrolysis by ionic liquid pretreatment. Appl. Biochem. Biotechnol. 137 140, 407 421] suggest that celluloses regenerated from IL solutions are subject to faster saccharification than untreated substrates. These encouraging results offer the possibility of using ILs as alternative and nonvolatile solvents for cellulose pretreatment. However, these studies are limited to two chloride-based ILs: (a) 1-butyl-3-methylimidazolium chloride ([BMIM]Cl), which is a corrosive, toxic and extremely hygroscopic solid (m.p. 70 C), and (b) 1-allyl-3-methylimidazolium chloride ([AMIM]Cl), which is viscous and has a reactive side-chain. Therefore, more in-depth research involving other ILs is much needed to explore this promising pretreatment route. For this reason, we studied a number of chloride- and acetate-based ILs for cellulose regeneration, including several ILs newly developed in our laboratory. This will enable us to select inexpensive, efficient and environmentally benign solvents for processing cellulosic biomass. Our data confirm that all regenerated celluloses are less crystalline (58 75% lower) and more accessible to cellulase (>2 times) than untreated substrates. As a result, regenerated Avicel

  14. Photophysics of 3,3'-diethyloxadicarbocyanine iodide (DODCI) in ionic liquid micelle and binary mixtures of ionic liquids: effect of confinement and viscosity on photoisomerization rate.

    PubMed

    Ghosh, Surajit; Mandal, Sarthak; Banerjee, Chiranjib; Rao, Vishal Govind; Sarkar, Nilmoni

    2012-08-01

    The dynamics of photoisomerization of 3,3'-diethyloxadicarbocyanine iodide (DODCI) has been investigated inside micellar environment formed by a surfactant-like ionic liquid, 1-butyl-3-methylimidazolium octyl sulfate ([C(4)mim][C(8)SO(4)]) and also in binary mixture of another ionic liquid, N,N,N-trimethyl-N-propyl ammonium bis(trifluoromethanesulfonyl) imide, ([N(3111)][Tf(2)N]) with methanol, acetonitrile, and n-propanol by using steady-state and picosecond time-resolved fluorescence spectroscopy. The entrapment of DODCI into the [C(4)mim][C(8)SO(4)] micellar environment led to the enhanced fluorescence intensity along with ~13 nm red shift in the emission maxima. A sharp increase in the fluorescence quantum yield (Φ) and the lifetime (τ(f)) near the critical micelle concentration (cmc) range is observed followed by saturation at higher concentration. As a result of partitioning of the probe molecules in the micellar phase from water, the nonradiative rate constant (k(nr)) of DODCI decreases 2.7 times than in water. The retardation of isomerization rate is due to high microviscosity of the micellar system compared to bulk water. In order to understand how the rate of isomerization depends on polarity as well as viscosity, we have measured isomerization rate in neat [N(3111)][Tf(2)N] and its mixtures with polar solvents, like methanol, acetonitrile, and n-propanol. The addition of methanol and n-propanol increases the polarity, but viscosity of the medium decreases. The nonradiative rate constant that represents the rate of photoisomerization decreases with the addition of the polar solvent in [N(3111)][Tf(2)N]. Complete analysis of all the experimental results indicate that viscosity is the sole parameter that regulates the rate of photoisomerization. Temperature-dependent k(nr) are used to determine the activation energy (E(a)) in 100 mM [C(4)mim][C(8)SO(4)] solution and neat [N(3111)][Tf(2)N] system. PMID:22793684

  15. Energy efficient microwave synthesis of mesoporous Ce0.5M0.5O2 (Ti, Zr, Hf) nanoparticles for low temperature CO oxidation in an ionic liquid – a comparative study

    DOE PAGESBeta

    Alammar, Tarek; Chow, Ying -Kit; Mudring, Anja -Verena

    2014-11-19

    Ce0.5M0.5O2 (M = Ti, Zr, Hf) nanoparticles have been successfully synthesized by microwave irradiation in the ionic liquid [C4mim][Tf2N] (1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)amide). The morphology, crystallinity, and chemical composition of the obtained materials were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDX), Raman spectroscopy, and N2–adsorption measurements. XRD and Raman spectroscopy analyses confirmed the formation of solid solutions with cubic fluorite structure. The catalytic activities of the Ce0.5M0.5O2 (M = Ti, Zr, Hf) nanoparticles were investigated in the low-temperature oxidation of CO. Ce0.5Zr0.5O2 nanospheres exhibit the best performance (100% conversion at 350 °C), followed by Ce0.5Hf0.5O2more » (55% conversion at 360 °C) and Ce0.5Ti0.5O2 (11% conversion at 350 °C). Heating the as-prepared Ce0.5Zr0.5O2 to 600 °C for extended time leads to a decrease in surface area and, as expected decreased catalytic activity. Depending on the ionic liquid the obtained Ce0.5Zr0.5O2 exhibits different morphologies, varying from nano-spheres in [C4mim][Tf2N] and [P66614][Tf2N] (P66614 = trishexyltetradecylphosphonium) to sheet-like assemblies in [C3mimOH][Tf2N] (C3mimOH = 1-(3-hydroxypropyl)-3-methylimidazolium). As a result, the microwave synthesis superiority to other heating methods like sonochemical synthesis and conventional heating was proven by comparative experiments where the catalytic activity of Ce0.5Zr0.5O2 obtained by alternate methods such as conventional heating was found to be poorer than that of the microwave-synthesised material.« less

  16. Vaporization of the prototypical ionic liquid BMImNTf₂ under equilibrium conditions: a multitechnique study.

    PubMed

    Brunetti, Bruno; Ciccioli, Andrea; Gigli, Guido; Lapi, Andrea; Misceo, Nicolaemanuele; Tanzi, Luana; Vecchio Ciprioti, Stefano

    2014-08-01

    The vaporization behaviour and thermodynamics of the ionic liquid 1-butyl-3-methylimidazolium bis(trifluoromethyl)sulfonylimide (BMImNTf2) were studied by combining the Knudsen Effusion Mass Loss (KEML) and Knudsen Effusion Mass Spectrometry (KEMS) techniques. KEML studies were carried out in a large temperature range (398-567) K by using effusion orifices with 0.3, 1, and 3 mm diameters. The vapor pressures so measured revealed no kinetically hindered vaporization effects and provided second-law vaporization enthalpies at the mean experimental temperatures in close agreement with literature. By exploiting the large temperature range covered, the heat capacity change associated with vaporization was estimated, resulting in a value of -66.8 J K(-1) mol(-1), much lower than that predicted from calorimetric measurements on the liquid phase and theoretical calculations on the gas phase. The conversion of the high temperature vaporization enthalpy to 298 K was discussed and the value Δ(l)(g)H(m)(298 K) = (128.6 ± 1.3) kJ mol(-1) assessed on the basis of data from literature and present work. Vapor pressure data were also processed by the third-law procedure using different estimations for the auxiliary thermal functions, and a Δ(l)(g)H(m)(298 K) consistent with the assessed value was obtained, although the overall agreement is sensitive to the accuracy of heat capacity data. KEMS measurements were carried out in the lower temperature range (393-467) K and showed that the largely prevailing ion species is BMIm(+), supporting the common view of BMImNTf2 vaporizing as individual, neutral ion pairs also under equilibrium conditions. By monitoring the mass spectrometric signal of this ion as a function of temperature, a second-law Δ(l)(g)H(m)(298 K) of 129.4 ± 7.3 kJ mol(-1) was obtained, well consistent with KEML and literature results. Finally, by combining KEML and KEMS measurements, the electron impact ionization cross section of BMIm(+) was estimated. PMID:24958199

  17. Influence of ionic association, transport properties, and solvation on the catalytic hydrogenation of 1,3-cyclohexadiene in ionic liquids.

    PubMed

    Podgoršek, Ajda; Salas, Gorka; Campbell, Paul S; Santini, Catherine C; Pádua, Agílio A H; Costa Gomes, Margarida F; Fenet, Bernard; Chauvin, Yves

    2011-10-27

    The influence of the nature of two different ionic liquids, namely 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, [C(1)C(4)Im][NTf(2)], and 1-butyl-2,3-dimethylimidazolium bis(trifluoromethylsulfonyl)imide, [C(1)C(1)C(4)Im][NTf(2)], on the catalytic hydrogenation of 1,3-cyclohexadiene with [Rh(COD)(PPh(3))(2)][NTf(2)] (COD = 1,5-cyclooctadiene) was studied. Initially, the effect of different concentrations of 1,3-cyclohexadiene on the molecular interactions and on the structure in two ionic liquids was investigated by NMR and by molecular dynamic simulations. It was found that in both ionic liquids 1,3-cyclohexadiene is solvated preferentially in the lipophilic regions. Furthermore, the higher solubility of 1,3-cyclohexadiene in [C(1)C(4)Im][NTf(2)] and the smaller positive values of the excess molar enthalpy of mixing for the 1,3-cyclohexadiene + [C(1)C(4)Im][NTf(2)] system in comparison with 1,3-cyclohexadiene + [C(1)C(1)C(4)Im][NTf(2)] indicate more favorable interactions between 1,3-cyclohexadiene and the C(1)C(4)Im(+) cation than with the C(1)C(1)C(4)Im(+) cation. Subsequently, diffusivity and conductivity measurements of the 1,3-cyclohexadiene + ionic liquid mixtures at different compositions allowed a characterization of mass and charge transport in the media and access to the ionicity of ionic liquids in the mixture. From the dependence of the ratio between molar conductivity and the conductivity inferred from NMR diffusion measurements, Λ(imp)/Λ(NMR), on concentration of 1,3-cyclohexadiene in the ionic liquid mixture, it was found that increasing the amount of 1,3-cyclohexadiene leads to a decrease in the ionicity of the medium. Finally, the reactivity of the catalytic hydrogenation of 1,3-cyclohexadiene using [Rh(COD)(PPh(3))(2)][NTf(2)] performed in [C(1)C(4)Im][NTf(2)] at different compositions of 1,3-cyclohexadiene and in [C(1)C(1)C(4)Im][NTf(2)] at one composition was related linearly to the viscosity, hence the reaction rate is

  18. Effect of water on the carbon dioxide absorption by 1-alkyl-3-methylimidazolium acetate ionic liquids.

    PubMed

    Stevanovic, Stéphane; Podgoršek, Ajda; Pádua, Agilio A H; Costa Gomes, Margarida F

    2012-12-13

    The absorption of carbon dioxide by the pure ionic liquids 1-ethyl-3-methylimidazolium acetate ([C(1)C(2)Im][OAc]) and 1-butyl-3-methylimidazolium acetate ([C(1)C(4)Im][OAc]) was studied experimentally from 303 to 343 K. As expected, the mole fraction of absorbed carbon dioxide is high (0.16 at 303 K and 5.5 kPa and 0.19 at 303 and 9.6 KPa for [C(1)C(2)Im][OAc] and [C(1)C(4)Im][OAc], respectively), does not obey Henry's law, and is compatible with the chemisorption of the gas by the liquid. Evidence of a chemical reaction between the gas and the liquid was found both by NMR and by molecular simulation. In the presence of water, the properties of the liquid absorber significantly change, especially the viscosity that decreases by as much as 25% (to 78 mPa s) and 30% (to 262 mPa s) in the presence of 0.2 mol fraction of water for [C(1)C(2)Im][OAc] and [C(1)C(2)Im][OAc] at 303 K, respectively. The absorption of carbon dioxide decreases when the water concentration increases: a decrease of 83% in CO(2) absorption is found for [C(1)C(4)Im][OAc] with 0.6 mol fraction of water at 303 K. It is proved in this work, by combining experimental data with molecular simulation, that the presence of water not only renders the chemical reaction between the gas and the ionic liquid less favorable but also lowers the (physical) solubility of the gas as it competes by the same solvation sites of the ionic liquid. The lowering of the viscosity of the liquid absorbent largely compensates these apparent drawbacks and the mixtures of [C(1)C(2)Im][OAc] and [C(1)C(2)Im][OAc] with water seem promising to be used for carbon dioxide capture. PMID:23145571

  19. Relating ionic liquids and polyethylene glycols to green chemistry, organometallic catalysis, and materials science

    NASA Astrophysics Data System (ADS)

    Klingshirn, Marc Allen

    The field of green chemistry has grown tremendously over the past years due to stricter environmental laws regulating the amount of toxic substances that are legally allowed into the environment. The objective of this work was to incorporate ILs and PEGs into gel type matrices and utilize them as solvent alternatives in hopes of helping advance the field of green chemistry and lowering environmental burden. Here, three new gel-type materials were studied. A PEG gel-silica sol composite and an IL-PEG gel were developed. Both materials were based on a cross-linked PEG hydrogel and its response to various inorganic salts. The new materials developed exhibited the same shrink-swell characteristics as the control PEG hydrogel, while the IL-PEG gel showed similar uptakes of linear alcohols from salt solutions. Additionally, when calcined, the PEG gel-silica sol composite was found to have unique morphologies that were dependent on PEG hydrogel concentration. The third material that was developed was a silica sol gel that was synthesized utilizing 1-butyl-3-methylimidazolium chloride as a (co)solvent. All previous work reported used ILs that had structures similar to surfactants that are traditionally used in creating high surface area materials. The work here presents a fundamental study of how short chained ILs can be used to produce high surface area materials and addresses questions such as how the IL orients itself within the matrix during the sol gel process. Another facet of the work involves the incorporation of ILs and PEGS into organometallic catalytic systems, specifically the hydroesterification of styrene and the copolymerization of styrene and carbon monoxide. The ILs' non-coordinating nature allows them to stabilize catalytically active charged species in addition to allowing for ease of catalyst recycling. The application of the presented work to the field of green chemistry includes the implementation of benign, non-volatile reaction media, specifically

  20. Ionic liquid-enhanced photooxidation of water using the polyoxometalate anion [P2W18O62](6-) as the sensitizer.

    PubMed

    Bernardini, Gianluca; Zhao, Chuan; Wedd, Anthony G; Bond, Alan M

    2011-07-01

    Simple polyoxometalate anions are known to be photoreduced in molecular solvents in the presence of 2-propanol or benzyl alcohol. The use of ionic liquids (ILs) as the solvent is now reported to also allow the photooxidation of water to be achieved. In particular, the photochemistry of the classic Dawson polyoxometalate salt K(6)[P(2)W(18)O(62)] has been studied in detail when water is present in the aprotic IL, 1-butyl-3-methylimidazolium tetrafluoroborate ([Bmim][BF(4)]) and the protic IL, diethanolamine hydrogen sulfate (DEAS). In these and other ILs, irradiation with white light (wavelength 275-750 nm) or UV light (wavelength 275-320 nm) leads to overall reduction of the [P(2)W(18)O(62)](6-) anion to [P(2)W(18)O(62)](7-) and concomitant oxidation of water to dioxygen and protons. The modified structure of bulk water present in ILs appears to facilitate its oxidation. Analogous results were obtained in aqueous solutions containing the protic IL as an electrolyte. The photoproducts (reduced polyoxometalate anion, dioxygen, and protons) were identified by, respectively, voltammetry, a Clark electrode, and monitoring of pH. The formal reversible potentials E(0)(F) for [P(2)W(18)O(62)](6-/7-/8-/9-/10-) couples are much more positive than in molecular solvents. The [P(2)W(18)O(62)](8-) and more reduced anions, if formed as intermediates, would efficiently reduce photoproducts H(+) or dioxygen to produce [P(2)W(18)O(62)](7-), rather than reform to [P(2)W(18)O(62)](6-). Thus, under photoirradiation conditions [P(2)W(18)O(62)](7-) acts as a kinetic sink so that in principle indirect splitting of water to produce dioxygen and dihydrogen can be achieved. The equivalent form of photooxidation does not occur in liquid water or in molecular solvents such as MeCN and MeCN/CH(2)Cl(2) containing added water, but does occur for solid K(6)[P(2)W(18)O(62)] in contact with water vapor. PMID:21591701

  1. Pressure Swing Absorption Device and Process for Separating CO{sub 2} from Shifted Syngas and its Capture for Subsequent Storage

    SciTech Connect

    Sirkar, Kamalesh; Jie, Xingming; Chau, John; Obuskovic, Gordana

    2013-03-31

    Using the ionic liquid (IL) 1-butyl-3-methylimidazolium dicyanamide ([bmim][DCA]) as the absorbent on the shell side of a membrane module containing either a porous hydrophobized ceramic tubule or porous hydrophobized polyether ether ketone (PEEK) hollow fiber membranes, studies for CO{sub 2} removal from hot simulated pre-combustion shifted syngas were carried out by a novel pressure swing membrane absorption (PSMAB) process. Helium was used as a surrogate for H{sub 2} in a simulated shifted syngas with CO{sub 2} around 40% (dry gas basis). In this cyclic separation process, the membrane module was used to achieve non-dispersive gas absorption from a high-pressure feed gas (689-1724 kPag; 100-250 psig) at temperatures between 25-1000C into a stationary absorbent liquid on the module shell side during a certain part of the cycle followed by among other cycle steps controlled desorption of the absorbed gases from the liquid in the rest of the cycle. Two product streams were obtained, one He-rich and the other CO{sub 2}-rich. Addition of polyamidoamine (PAMAM) dendrimer of generation 0 to IL [bmim][DCA] improved the system performance at higher temperatures. The solubilities of CO{sub 2} and He were determined in the ionic liquid with or without the dendrimer in solution as well as in the presence or absence of moisture; polyethylene glycol (PEG) 400 was also studied as a replacement for the IL. The solubility selectivity of the ionic liquid containing the dendrimer for CO{sub 2} over helium was considerably larger than that for the pure ionic liquid. The solubility of CO{sub 2} and CO{sub 2}-He solubility selectivity of PEG 400 and a solution of the dendrimer in PEG 400 were higher than the corresponding ones in the IL, [bmim][DCA]. A mathematical model was developed to describe the PSMAB process; a numerical solution of the governing equations described successfully the observed performance of the PSMAB process for the pure ionic liquid-based system.

  2. Mild yet phase-selective preparation of TiO2 nanoparticles from ionic liquids - a critical study

    NASA Astrophysics Data System (ADS)

    Alammar, Tarek; Noei, Heshmat; Wang, Yuemin; Mudring, Anja-Verena

    2013-08-01

    The phase selective synthesis of nanocrystalline TiO2, titania, in ionic liquids (ILs) is explored. The influence not only of the IL but also of the Ti-precursor, pH, and temperature is investigated. Sonochemical synthesis, microwave synthesis and conventional heating are compared. In the case of Ti(OiPr)4 (OiPr = isopropyl) as the Ti-source the ILs [C4mim][Tf2N] (1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)amide), [C3mimOH][Tf2N] (1-(3-hydroxypropyl)-3-methylimidazolium bis(trifluoromethanesulfonyl)amide), [C4Py][Tf2N] (butylpyridinium bis(trifluoromethanesulfonyl)amide), [N1888][Tf2N] (methyltrioctylammonium bis(trifluoromethanesulfonyl)amide), and [P66614][Tf2N] (tetradecyltrihexyl phosphonium bis(trifluoromethanesulfonyl)amide) led at ambient temperature to TiO2 in the form of anatase. The morphology of nano-anatase is controlled by the IL cation. Anatase nanospheres with a crystal size below 10 nm are obtained in [C3mimOH][Tf2N], [P66614][Tf2N] and [C4Py][Tf2N], whilst nanorods with a length and diameter of ~10 to 20 and 5 nm are formed in [N1888][Tf2N] and spindle-shaped particles with an average length of 10-25 nm are formed in [C4mim][Tf2N]. Calcination at temperatures above 730 °C leads to rutile. When using TiCl4 as the Ti-precursor an anatase-rutile mixture forms under ambient conditions. Pure rutile can be obtained under ambient conditions in the presence of an appropriate volume of aqueous HCl. At moderate to high pH values pure anatase can be obtained even from TiCl4. The photocatalytic activity of the obtained TiO2 materials has been assessed by the photodegradation of an aqueous methyl orange solution under UV light. The results indicate that the photocatalytic activity of anatase-brookite mixtures obtained in [C4mim][Tf2N], [N1888][Tf2N] and [P66614][Tf2N] is higher than that of pure anatase which is formed in [C3mimOH][Tf2N] and [C4Py][Tf2N] and competitive with commercially available catalysts.The phase selective synthesis of

  3. Advances in the electrodeposition of aluminum from ionic liquid based electrolytes

    NASA Astrophysics Data System (ADS)

    Leadbetter, Kirt C.

    . Advancements of this nonaqueous aluminum plating process have the potential to lead to a novel and competitive commercial aluminum deposition process. In this investigation aluminum electrodeposition from ionic liquid based electrolytes onto steel, copper and magnesium substrates without conversion coatings or strike layers was evaluated in six different ionic liquid based electrolytes in two technical setups. Three of which are commercially available aluminum plating electrolytes, three of which, discussed in literature were created on site by research personnel in the laboratory. The three commercially available electrolytes were: 1-Butyl-3-methylimidazolium chloride ([BMIm]Cl) * 1.5 AlCl3 with proprietary additives from IoLiTec, 1-Ethyl-3-methylimidazolium chloride ([EMIm]Cl) * 1.5 AlCl3 with proprietary additives from IoLiTec, and BasionicsTM AL-02, an aluminum plating electrolyte containing [EMIm]Cl * 1.5 AlCl3 with additives from BASF. The three electrolytes created on site were based on the 1-ethyl-3-methylimidazolium chloride ionic liquid with added 1.5 AlCl3 and one with added sodium dodecyl sulfate. Small scale plating tests in a 25-mL plating cell were conducted to provide a comparative analysis of the six different electrolytes considered. From these investigations, two were chosen to be evaluated in a larger 1-liter plating cell; designed and constructed to provide a more realistic evaluation of plating parameters with selected electrolytes to better portray industrial electroplating conditions. The effect of current density (10-40 mA/cm 2), temperature (30-90° Celsius) and plating bath agitation on current efficiency, corrosion resistance by the ASTM B117 method, adhesion, microstructure, and chemical composition (evaluated with energy-dispersive x-ray spectroscopy) of the plated Al-layer was explored in both the 25-mL and 1-L plating cell investigations. In addition development of pre- and post-treatment processes for the metal substrates was attempted. While

  4. Theoretical and computational studies of renewable energy materials: Room temperature ionic liquids and proton exchange membranes

    NASA Astrophysics Data System (ADS)

    Feng, Shulu

    2011-12-01

    Two kinds of renewable energy materials, room temperature ionic liquids (RTILs) and proton exchange membranes (PEMs), especially Nafion, are studied by computational and theoretical approaches. The ultimate purpose of the present research is to design novel materials to meet the future energy demands. To elucidate the effect of alkyl side chain length and anion on the structure and dynamics of the mixtures, molecular dynamics (MD) simulations of three RTILs/water mixtures at various water mole fractions: 1-butyl-3-methylimidazolium (BMIM+)/BF4-, 1-octyl-3-methylimidazolium (OMIM+)/BF4-, and OMIM +/Cl- are performed. Replacing the BMIM + cation with OMIM+ results in stronger aggregation of the cations as well as a slower diffusion of the anions, and replacing the BF4- anion with Cl- alters the water distribution at low water mole fractions and slows diffusion of the mixtures. Potential experimental manifestations of these behaviors in both cases are provided. Proton solvation properties and transport mechanisms are studied in hydrated Nafion, by using the self-consistent multistate empirical valence bond (SCI-MS-EVB) method. It is found that by stabilizing a more Zundel-like (H5O 2+) structure in the first solvation shells, the solvation of excess protons, as well as the proton hydration structure are both influenced by the sulfonate groups. Hydrate proton-related hydrogen bond networks are observed to be more stable than those with water alone. In order to characterize the nature of the proton transport (PT), diffusive motion, Arrhenius activation energies, and transport pathways are calculated and analyzed. Analysis of diffusive motion suggests that (1) a proton-hopping mechanism dominates the proton transport for the studied water loading levels and (2) there is an obvious degree of anti-correlation between the proton hopping and the vehicular transport. The activation energy drops rapidly with an increasing water content when the water loading level is smaller

  5. The effect of C2 substitution on melting point and liquid phase dynamics of imidazolium based-ionic liquids: insights from molecular dynamics simulations

    SciTech Connect

    Zhang, Y; Maginn, EJ

    2012-01-01

    Using molecular dynamics simulations, the melting points and liquid phase dynamic properties were studied for four alkyl-imidazolium-based ionic liquids, 1-n-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF6]), 1-n-butyl-2,3-dimethylimidazolium hexafluorophosphate ([BMMIM][PF6]), 1-ethyl-3-methylimidazolium hexafluorophosphate ([EMIM][PF6]), and 1-ethyl-2,3-dimethylimidazolium hexafluorophosphate ([EMMIM][PF6]), respectively. Experimentally it has been observed that the substitution of a methyl group for a hydrogen at the C2 position of the cation ring leads to an increase in both the melting point and liquid phase viscosity, contrary to arguments that had been made regarding associations between the ions. The melting points of the four ionic liquids were accurately predicted using simulations, as were the trends in viscosity. The simulation results show that the origin of the effect is mainly entropic, although enthalpy also plays an important role.

  6. Synthesis and characterization of ionomers as polymer electrolytes for energy conversion devices

    NASA Astrophysics Data System (ADS)

    Oh, Hyukkeun

    group and a poly(ether ether ketone) backbone showed the highest proton conductivity and proton diffusion coefficient among the three ionomers, demonstrating the effect of the perfluorinated side chains. The proton conductivity of the novel ionomer was comparable to that of Nafion over a wide humidity range and temperature. A lithium perfluorosulfonate ionomer based on aromatic poly(arylene ether)s with pendant lithium perfluoroethyl sulfonates was prepared by ion exchange of the perlfuorosulfonic acid ionomer, and subsequently incoroporated into a lithium-ion battery cell as a single-ion conducting electrolyte. The microporous polymer film saturated with organic carbonates exhibited a nearly unity Li + transfer number, high ionic conductivity (e.g. > 10-3 S m-1 at room temperature) over a wide range of temperatures, high electrochemical stability, and excellent mechanical properties. Excellent cyclability with almost identical charge and discharge capacities have been demonstrated at ambient temperature in the batteries assembled from the prepared single-ion conductors. The mechanical stability of the polymer film was attributed to the rigid polymer backbone which was largely unaffected by the presence of plasticizing organic solvents, while the porous channels with high concentration of the perfluorinated side chains resulted in high ionic conductivity. The expected high charge-rate performance was not achieved, however, due to the high interfacial impedance present between the polymer electrolyte and the electrodes. Several procedural modifications were employed in order to decrease the interfacial impedance of the battery cell. The poly(arylene ether) based ionomer was saturated with an ionic liquid mixture, in order to explore the possibility of its application as a safe, inflammable electrolyte. A low-viscosity ionic liquid with high ionic conductivity, 1-butyl-3-methylimidazolium thiocyanate which has never been successfully utilized as an electrolyte for lithium

  7. Operationally Simple Synthesis of N,N-Diethyl-3-Methylbenzamide (DEET) Using COMU as a Coupling Reagent

    ERIC Educational Resources Information Center

    Withey, Jonathan M.; Bajic, Andrea

    2015-01-01

    A novel procedure is described where students use COMU [(1-cyano-2-ethoxy-2-oxoethylidenaminooxy)dimethylamino-morpholino-carbenium hexafluorophosphate], as a nonhazardous partner, in the one-pot coupling of a carboxylic acid and amine producing N,N-diethyl-3-methylbenzamide (DEET). Fundamental principles of carbonyl reactivity are understood,…

  8. Synthesis and X-ray structures of metallocenium diamines of ironand cobalt

    SciTech Connect

    Inyushin, Sviatoslav; Shafir, Alexandr; Sheats, John E.; Minihane, Michael; Whitten Jr., Charles E.; Arnold, John

    2004-05-30

    A detailed, reproducible synthesis of 1,10-diaminocobaltocenium hexafluorophosphate is provided. The compound can be made on gram scales in several steps starting from 1,10-dimethylcobaltoceniumsalts. The X-ray structures of 1,10-diamino cobaltoceniumhexafluorophosphate and a related 1,10-diamino ferrocenium salt, are described.

  9. Vibrational Spectroscopic Study of Imidazolium Dicationic Ionic Liquids: Effect of Cation Alkyl Chain Length

    NASA Astrophysics Data System (ADS)

    Moumene, T.; Belarbi, E. H.; Haddad, B.; Villemin, D.; Abbas, O.; Khelifa, B.; Bresson, S.

    2016-05-01

    Two new dicationic ionic liquids were synthesized: bis-methyl imidazolium methylidene hexafluorophosphate [M(CH2)IM2 +][2PF 6 - ] and bis-methyl imidazolium propylidene hexafluorophosphate [M(CH2)3IM2 +][2PF 6 - ]. Their structures were identified by H, C, P, F NMR, FTIR/ATR, and FT-Raman spectroscopies in order to study the effect of cation alkyl chain length on vibration behaviors. Several changes were recorded, which were related to alkyl chain length. A frequency shift was observed in some modes while others remained insensitive. A greater number of peaks was found in the FTIR/ATR spectra and the FT-Raman spectra with increasing alkyl chain length, which indicated that chain length influences the N-C connection twisting. More peaks with strong intensity appeared for longer alkyl chain lengths.

  10. Vibrational Spectroscopic Study of Imidazolium Dicationic Ionic Liquids: Effect of Cation Alkyl Chain Length

    NASA Astrophysics Data System (ADS)

    Moumene, T.; Belarbi, E. H.; Haddad, B.; Villemin, D.; Abbas, O.; Khelifa, B.; Bresson, S.

    2016-05-01

    Two new dicationic ionic liquids were synthesized: bis-methyl imidazolium methylidene hexafluorophosphate [M(CH2)IM2 +][2PF{6/-}] and bis-methyl imidazolium propylidene hexafluorophosphate [M(CH2)3IM2 +][2PF{6/-}]. Their structures were identified by H, C, P, F NMR, FTIR/ATR, and FT-Raman spectroscopies in order to study the effect of cation alkyl chain length on vibration behaviors. Several changes were recorded, which were related to alkyl chain length. A frequency shift was observed in some modes while others remained insensitive. A greater number of peaks was found in the FTIR/ATR spectra and the FT-Raman spectra with increasing alkyl chain length, which indicated that chain length influences the N-C connection twisting. More peaks with strong intensity appeared for longer alkyl chain lengths.

  11. Amide and Peptide Bond Formation in Water at Room Temperature.

    PubMed

    Gabriel, Christopher M; Keener, Megan; Gallou, Fabrice; Lipshutz, Bruce H

    2015-08-21

    A general and environmentally responsible method for the formation of amide/peptide bonds in an aqueous micellar medium is described. Use of uronium salt (1-cyano-2-ethoxy-2-oxoethylidenaminooxy)dimethylaminomorpholinocarbenium hexafluorophosphate (COMU) as a coupling reagent, 2,6-lutidine, and TPGS-750-M represents mild conditions associated with these valuable types of couplings. The aqueous reaction medium is recyclable leading to low E Factors. PMID:26251952

  12. Ionic liquid coated magnetic core/shell Fe3O4@SiO2 nanoparticles for the separation/analysis of linuron in food samples

    NASA Astrophysics Data System (ADS)

    Chen, Jieping; Zhu, Xiashi

    2015-02-01

    Three hydrophobic ionic liquids (ILs) including 1-butyl-3-methylimidazole hexafluorophosphate ([BMIM]PF6), 1-hexyl-3-methyl-imidazole hexafluorophosphate ([HMIM]PF6), and 1-octyl-3-methylimidazole hexafluoro-phosphate ([OMIM]PF6) coated Fe3O4@SiO2 nanoparticles with core-shell structure to prepare magnetic solid phase extraction agent (Fe3O4@SiO2@ILs) and establish a new method of magnetic solid phase extraction (MSPE) coupled with UV spectrometry for separation/analysis of linuron. The results showed that linuron was adsorbed rapidly by Fe3O4@SiO2@[OMIM]PF6 and eluanted by ethanol. Under the optimal conditions, preconcentration factor of the proposed method was 10-fold. The linear range, detection limit, correlation coefficient (R) and relative standard deviation (RSD) were found to be 0.04-20.00 μg mL-1, 5.0 ng mL-1, 0.9993 and 2.8% (n = 3, c = 4.00 μg mL-1), respectively. The Fe3O4@SiO2 nanoparticles could be used repeatedly for 10 times. This proposed method has been successfully applied to the determination of linuron in food samples.

  13. Magnetic solid phase extraction using ionic liquid-coated core-shell magnetic nanoparticles followed by high-performance liquid chromatography for determination of Rhodamine B in food samples.

    PubMed

    Chen, Jieping; Zhu, Xiashi

    2016-06-01

    Three hydrophobic ionic liquids (ILs) (1-butyl-3-methylimidazole hexafluorophosphate ([BMIM]PF6), 1-hexyl-3-methyl-imidazole hexafluoro-phosphate ([HMIM]PF6), and 1-octyl-3-methylimidazole hexafluorophosphate ([OMIM]PF6)) were used to coat Fe3O4@SiO2 nanoparticles (NPs) with core-shell structures to prepare magnetic solid phase extraction (MSPE) agents (Fe3O4@SiO2@IL). A novel method of MSPE coupled with high-performance liquid chromatography for the separation/analysis of Rhodamine B was then established. The results showed that Rhodamine B was adsorbed rapidly on Fe3O4@SiO2@[OMIM]PF6 and was released using ethanol. Under optimal conditions, the pre-concentration factor for the proposed method was 25. The linear range, limit of detection (LOD), correlation coefficient (R), and relative standard deviation (RSD) were found to be 0.50-150.00 μgL(-1), 0.08 μgL(-1), 0.9999, and 0.51% (n=3, c=10.00 μgL(-1)), respectively. The Fe3O4@SiO2 NPs could be re-used up to 10 times. The method was successfully applied to the determination of Rhodamine B in food samples. PMID:26830554

  14. Effect of combinations of additives on the performance of lithium ion batteries

    NASA Astrophysics Data System (ADS)

    Santee, Stuart; Xiao, Ang; Yang, Li; Gnanaraj, Joe; Lucht, Brett L.

    Commercial lithium-ion batteries have excellent performance at room temperature for a few years. However, the calendar life and thermal stability (>50 °C) need to be improved for many applications, including electric vehicles. We have conducted an investigation of the effect of thermal stabilizing additives, including dimethyl acetamide, vinylene carbonate, and lithium bis(oxalato) borate, on the performance of lithium ion batteries stored at 70 °C for one month. The reactions of the lithium hexafluorophosphate/carbonate electrolyte, with and without electrolyte additives, with the surface of the electrodes after initial formation cycling have been analyzed via a combination of IR-ATR and XPS.

  15. Synthesis and characterization of hexakis(alkyl isocyanide) and hexakis(aryl isocyanide) complexes of technetium(I)

    SciTech Connect

    Abrams, M.J.; Davison, A.; Jones, A.G.; Costello, C.E.; Pang, H.

    1983-09-28

    The complexes, hexakis(alkyl isocyanide) technetium(I) hexafluorophosphate (Tc(CNR)/sub 6/)PF/sub 6/ (where R = tert-butyl, methyl, cyclohexyl, and phenyl), have been prepared by reduction of the pertechnetate ion with aqueous sodium dithionite (Na/sub 2/S/sub 2/O/sub 4/) in the presence of the isocyanide ligands. These complexes have been characterized by elemental analysis, optical, ir, and /sup 1/H NMR spectroscopy, conductance, cyclic voltammetry, and field desorption mass spectrometry.

  16. Gold(I)-Catalyzed Intramolecular Hydroamination of N-Allylic,N'-Aryl Ureas to form Imidazolidin-2-ones.

    PubMed

    Li, Hao; Song, Feijie; Widenhoefer, Ross A

    2011-04-18

    Treatment of N-allylic,N'-aryl ureas with a catalytic 1:1 mixture of di-tert-butyl-o-biphenylphoshphine gold(I) chloride and silver hexafluorophosphate (1 mol %) in chloroform at room temperature led to 5-exo hydroamination to form the corresponding imidazolidin-2-ones in excellent yield. In the case of N-allylic ureas that possessed an allylic alkyl, benzyloxymethyl, or acetoxymethyl substituent, gold(I)-catalyzed 5-exo hydroamination leads to formation of the corresponding trans-3,4-disubstituted imidazolidin-2-ones in excellent yield with ≥50:1 diastereoselectivity. PMID:21709731

  17. Partition coefficients of organic compounds in new imidazolium based ionic liquids using inverse gas chromatography.

    PubMed

    Revelli, Anne-Laure; Mutelet, Fabrice; Jaubert, Jean-Noël

    2009-06-01

    Partition coefficients of organic compounds in four ionic liquids: 1-ethanol-3-methylimidazolium tetrafluoroborate, 1-ethanol-3-methylimidazolium hexafluorophosphate, 1,3-dimethylimidazolium dimethylphosphate and 1-ethyl-3-methylimidazolium diethylphosphate were measured using inverse gas chromatography from 303.3 to 332.55K. The influence of gas-liquid and gas-solid interfacial adsorption of different solutes on ionic liquids was also studied. Most of the polar solutes were retained largely by partition while light hydrocarbons were retained predominantly by interfacial adsorption on the ionic liquids studied in this work. The solvation characteristics of the ionic liquids were evaluated using the Abraham solvation parameter model. PMID:19414174

  18. Diblock Polyelectrolytic Copolymers Containing Cationic Iron and Cobalt Sandwich Complexes: Living ROMP Synthesis and Redox Properties.

    PubMed

    Gu, Haibin; Ciganda, Roberto; Hernandez, Ricardo; Castel, Patricia; Zhao, Pengxiang; Ruiz, Jaime; Astruc, Didier

    2016-04-01

    Diblock metallopolymer polyelectrolytes containing the two redox-robust cationic sandwich units [CoCp'Cp](+) and [FeCp'(η(6)-C6 Me6)](+) (Cp = η(5)-C5 H5; Cp' = η(5)-C5H4-) as hexafluorophosphate ([PF6](-)) salts are synthesized by ring-opening metathesis polymerization using Grubbs' third generation catalyst. Their electrochemical properties show full chemical and electrochemical reversibilities allowing fine determination of the copolymer molecular weight using Bard-Anson's electrochemical method by cyclic voltammetry. PMID:26841204

  19. Multi-scale modelling of supercapacitors: From molecular simulations to a transmission line model

    NASA Astrophysics Data System (ADS)

    Pean, C.; Rotenberg, B.; Simon, P.; Salanne, M.

    2016-09-01

    We perform molecular dynamics simulations of a typical nanoporous-carbon based supercapacitor. The organic electrolyte consists in 1-ethyl-3-methylimidazolium and hexafluorophosphate ions dissolved in acetonitrile. We simulate systems at equilibrium, for various applied voltages. This allows us to determine the relevant thermodynamic (capacitance) and transport (in-pore resistivities) properties. These quantities are then injected in a transmission line model for testing its ability to predict the charging properties of the device. The results from this macroscopic model are in good agreement with non-equilibrium molecular dynamics simulations, which validates its use for interpreting electrochemical impedance experiments.

  20. Electrochemical studies of hydrogen chloride gas in several room temperature ionic liquids: mechanism and sensing.

    PubMed

    Murugappan, Krishnan; Silvester, Debbie S

    2016-01-28

    The electrochemical behaviour of highly toxic hydrogen chloride (HCl) gas has been investigated in six room temperature ionic liquids (RTILs) containing imidazolium/pyrrolidinium cations and range of anions on a Pt microelectrode using cyclic voltammetry (CV). HCl gas exists in a dissociated form of H(+) and [HCl2](-) in RTILs. A peak corresponding to the oxidation of [HCl2](-) was observed, resulting in the formation of Cl2 and H(+). These species were reversibly reduced to H2 and Cl(-), respectively, on the cathodic CV scan. The H(+) reduction peak is also present initially when scanned only in the cathodic direction. In the RTILs with a tetrafluoroborate or hexafluorophosphate anion, CVs indicated a reaction of the RTIL with the analyte/electrogenerated products, suggesting that these RTILs might not be suitable solvents for the detection of HCl gas. This was supported by NMR spectroscopy experiments, which showed that the hexafluorophosphate ionic liquid underwent structural changes after HCl gas electrochemical experiments. The analytical utility was then studied in 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C2mim][NTf2]) by utilising both peaks (oxidation of [HCl2](-) and reduction of protons) and linear calibration graphs for current vs. concentration for the two processes were obtained. The reactive behaviour of some ionic liquids clearly shows that the choice of the ionic liquid is very important if employing RTILs as solvents for HCl gas detection. PMID:26697927

  1. Bioelectrocatalysis in ionic liquids. Examining specific cation and anion effects on electrode-immobilized cytochrome c.

    PubMed

    DiCarlo, Cory M; Compton, David L; Evans, Kervin O; Laszlo, Joseph A

    2006-05-01

    Cytochrome c immobilized on alkylthiol self-assembled monolayers exhibits a characteristic Fe(II)/Fe(III) redox signal that is lost when exposed to ionic liquids composed of a butylimidazolium cation combined with either hexafluorophosphate or bis(trifluoromethylsulfonyl)imide anion. In this study it was shown that exposure to the aqueous solubilized ionic liquid components, butyl-, hexyl-, and octyl-imidazolium cations and hexafluorophosphate, tetrafluoroborate, and bis(trifluoromethylsulfonyl)imide anions, resulted in partial electrochemical signal loss. Absorbance and fluorescence measurements showed that signal loss due to the cationic ionic liquid component followed a different mechanism than that of the anionic component. Although a portion of the signal was recoverable, irreversible signal loss also occurred in both cases. The source of the irreversible component is suggested to be the loss of protein secondary structure through complexation between the ionic liquid components and the protein surface residues. The reversible electrochemical signal loss is likely due to interfacial interactions imposed between the electrode and the cytochrome heme group. The influence of the amount of exposed surface residues was explored with a simplified model protein, microperoxidase-11. PMID:16009598

  2. Preparation and characterization of novel crown ether functionalized ionic liquid-based solid-phase microextraction coatings by sol-gel technology.

    PubMed

    Zhou, Xin; Xie, Peng-fei; Wang, Jiang; Zhang, Bei-bei; Liu, Ming-ming; Liu, Han-lan; Feng, Xiong-han

    2011-06-10

    A novel crown ether functionalized ionic liquid (IL), 1-allyl-3-(6'-oxo-benzo-15-crown-5 hexyl) imidazolium hexafluorophosphate was synthesized and used as selective stationary phase to prepare task-specific IL-based solid phase microextraction (SPME) fibers by sol-gel method and free radical cross-linking technology. The underlying mechanism of the sol-gel reaction was proposed and the successful chemical bonding of the crown ether functionalized IL to the formed hybrid organic-inorganic copolymer coating was confirmed by FT-IR spectroscopy. The performance of this in situ created crown ether functionalized IL-based SPME fibers, was investigated in detail. The coating has porous surface structure, stable performance in high temperature (to 340 °C) and in different solutions (water, organic solvent, acid and alkali), and good coating preparation reproducibility. In contrast to the sol-gel derived 1-allyl-3-methyl imidazolium hexafluorophosphate-based coating prepared in our previous work with the identical procedure, the extraction performance of this newly developed sol-gel crown ether functionalized IL-based coating was superior for alcohols, phthalate esters, phenolic environmental estrogens, fatty acids and aromatic amines due to the introduction of benzo-15-crown-5 functional group in IL structure. Moreover, it was shown to provide higher or comparable extraction efficiencies for most analytes studied than did the commercial PDMS, PDMS/DVB and PA fibers. PMID:21531419

  3. Hydrophobic task-specific ionic liquids: synthesis, properties and application for the capture of SO2.

    PubMed

    Tian, Shidong; Hou, Yucui; Wu, Weize; Ren, Shuhang; Qian, Jianguo

    2014-08-15

    The capture of SO2 by ionic liquids (ILs) has drawn much attention all over the world. However, ILs can absorb not only SO2 but also water from flue gas. The removal of water from ILs is necessary for reusing the absorbent. In order to reduce the energy costs of removing water, it would be helpful to weaken the interactions between ILs and water. In this work, two kinds of hydrophobic task-specific ILs, 1-(2-diethyl-aminoethyl)-3-methylimidazolium hexafluorophosphate ([Et2NEmim] [PF6]) and 1-(2-diethyl-aminoethyl)-1-methylpyrrolidinium hexafluorophosphate ([Et2NEmpyr][PF6]), were designed and synthesized. Thermal stability and physical properties of the ILs were studied. Furthermore, the application of the ILs for the capture of SO2 and the absorption mechanism were systematically investigated. It has been found that both of the ILs are immiscible with water, and [Et2NEmim][PF6] has much lower viscosity, much higher thermal stability and much higher SO2 absorption rate than [Et2NEmpyr][PF6]. [Et2NEmim][PF6] shows high SO2 absorption capacities up to 2.11 mol SO2 per mole IL (pure SO2) and 0.94 mol SO2 per mole IL (3% SO2) under hydrous conditions at 30 °C. The result suggests that [Et2NEmim][PF6] is a promising recyclable absorbent for the capture of SO2. PMID:24998204

  4. Facile fabrication of ionic liquid doped polycarbazole coating for the headspace solid-phase microextraction of some environmental pollutants.

    PubMed

    Feng, Yuanyuan; Wu, Mian; Zhao, Faqiong; Zeng, Baizhao

    2016-02-01

    A novel polycarbazole (PCz)-ionic liquid (IL, i.e. 1-hydroxyethyl-3-methylimidazolium bis[(trifluoromethyl)sulfonyl]imide, [HOEMIm][NTf2]) composite coating (PCz-IL) was fabricated by electrodeposition. The IL could facilitate the electrodeposition of poor-conductive PCz and a more porous coating was obtained. The composite coating exhibited enhanced extraction capacity for some environmental pollutants (i.e. o-chlorotoluene, p-bromotoluene, o-nitrotoluene, m-nitrotoluene, p-nitrotoluene), as they could interact through π-π and hydrophobic interactions. Compared with [HOEMIm][NTf2] coated fiber, some other PCz-IL fibers (here IL=1-hydroxyethyl-3-methylimidazolium hexafluorophosphate and 1-methyl-3-octylimidazolium hexafluorophosphate) and commercial fibers (i.e. polydimethylsiloxane and polyacrylate), the PCz-IL fiber showed better performance. It was used for the determination of the environmental pollutants by coupling with gas chromatography, the limits of detection were 47.8-65.9 ng L(-1) under the optimized conditions and the linear ranges were 0.1-500 μg L(-1) with correlation coefficients above 0.9947 for different compounds. The relative standard deviations (RSDs) were 3.4-4.6% for five successive extractions with single fiber, and the RSDs for inter-fiber were 6.5-10.4% (n=5). The fiber was successfully applied to the detection of real samples and the recoveries for standards added were 88.6-108.8% with RSDs below 9.7%. PMID:26653460

  5. Structural and Formulation Factors Influencing Pyridinium Lipid-based Gene Transfer

    PubMed Central

    Zhu, Lin; Lu, Yan; Miller, Duane D.; Mahato, Ram I.

    2009-01-01

    A series of pyridinium lipids containing a heterocyclic ring and a nitrogen atom were synthesized to determine the structure-activity relationship for gene delivery. Pyrylium chloroaluminate was synthesized by monoacylation of mesityl oxide and converted into pyrylium hexafluorophosphate, which was used as the key intermediate for reaction with different primary amines, to yield hydroxyethylpyridinium hexafluorophosphate and aminoethylpyridinium hexafluorophosphate. Acylation of these pyridinium salts with different types of fatty acid chlorides afforded the final pyridinium lipids, which were mixed with a co-lipid, such as L-alpha-dioleoylphosphatidylethanolamine (DOPE) and cholesterol (Chol) to prepare cationic liposomes by sonication. These liposomes were mixed with plasmid DNA encoding enhanced green fluorescent protein (pCMS-EGFP) or luciferase (pDNA3-Luc) and transfected into Chinese Hamster Ovary (CHO) cells. Several factors including hydrophobic anchor chain length, anchor chain type, configuration of double bond, linker type, co-lipid type, cationic lipid: co-lipid molar ratio, charge ratio (N/P), and cell type had significant influence on transfection efficiency and cytotoxicity. Pyridinium lipids with amide linker showed significantly higher transfection efficiency compared to their ester counterparts. Liposomes prepared at 1:1 molar ratio of pyridinium lipid and co-lipid showed higher transfection efficiency when either DOPE or cholesterol was used as a co-lipid to prepare cationic liposomes for complex formation with plasmid DNA at 3:1(+/−) charge ratio. Pyridinium liposomes based on hydrophobic anchor chain length of 16 showed higher transfection efficiency and lower cytotoxicity. The pyridinium lipid with trans-configuration of the double bond in fatty acid chain showed higher transfection efficiency than its counterpart with cis-configuration at the same fatty acid chain length. In the presence of serum, C16:0 and Lipofectamine significantly

  6. Anion-Tunable Properties and Electrochemical Performance of Functionalized Ferrocene Compounds

    PubMed Central

    Cosimbescu, Lelia; Wei, Xiaoliang; Vijayakumar, M.; Xu, Wu; Helm, Monte L.; Burton, Sarah D.; Sorensen, Christina M.; Liu, Jun; Sprenkle, Vincent; Wang, Wei

    2015-01-01

    We report a series of ionically modified ferrocene compounds for hybrid lithium-organic non-aqueous redox flow batteries, based on the ferrocene/ferrocenium redox couple as the active catholyte material. Tetraalkylammonium ionic moieties were incorporated into the ferrocene structure, in order to enhance the solubility of the otherwise relatively insoluble ferrocene. The effect of various counter anions of the tetraalkylammonium ionized species appended to the ferrocene, such as bis(trifluoromethanesulfonyl)imide, hexafluorophosphate, perchlorate, tetrafluoroborate, and dicyanamide on the solubility of the ferrocene was investigated. The solution chemistry of the ferrocene species was studied, in order to understand the mechanism of solubility enhancement. Finally, the electrochemical performance of these ionized ferrocene species was evaluated and shown to have excellent cell efficiency and superior cycling stability. PMID:26374254

  7. Effect of simultaneous electrical and thermal treatment on the performance of bulk heterojunction organic solar cell blended with organic salt

    SciTech Connect

    Sabri, Nasehah Syamin; Yap, Chi Chin; Yahaya, Muhammad; Salleh, Muhamad Mat

    2013-11-27

    This work presents the influence of simultaneous electrical and thermal treatment on the performance of organic solar cell blended with organic salt. The organic solar cells were composed of indium tin oxide as anode, poly[2-methoxy-5-(2-ethylhexyloxy)-1,4-phenylenevinylene]: (6,6)-phenyl-C61 butyric acid methyl ester: tetrabutylammonium hexafluorophosphate blend as organic active layer and aluminium as cathode. The devices underwent a simultaneous fixed-voltage electrical and thermal treatment at different temperatures of 25, 50 and 75 °C. It was found that photovoltaic performance improved with the thermal treatment temperature. Accumulation of more organic salt ions in the active layer leads to broadening of p-n doped regions and hence higher built-in electric field across thin intrinsic layer. The simultaneous electrical and thermal treatment has been shown to be able to reduce the electrical treatment voltage.

  8. Radiofrequency attenuator and method

    DOEpatents

    Warner, Benjamin P.; McCleskey, T. Mark; Burrell, Anthony K.; Agrawal, Anoop; Hall, Simon B.

    2009-01-20

    Radiofrequency attenuator and method. The attenuator includes a pair of transparent windows. A chamber between the windows is filled with molten salt. Preferred molten salts include quarternary ammonium cations and fluorine-containing anions such as tetrafluoroborate (BF.sub.4.sup.-), hexafluorophosphate (PF.sub.6.sup.-), hexafluoroarsenate (AsF.sub.6.sup.-), trifluoromethylsulfonate (CF.sub.3SO.sub.3.sup.-), bis(trifluoromethylsulfonyl)imide ((CF.sub.3SO.sub.2).sub.2N.sup.-), bis(perfluoroethylsulfonyl)imide ((CF.sub.3CF.sub.2SO.sub.2).sub.2N.sup.-) and tris(trifluoromethylsulfonyl)methide ((CF.sub.3SO.sub.2).sub.3C.sup.-). Radicals or radical cations may be added to or electrochemically generated in the molten salt to enhance the RF attenuation.