Science.gov

Sample records for 10-8 photons cm-2

  1. Key comparison BIPM.RI(I)-K6 of the standards for absorbed dose to water at 10 g cm-2 of the NMIJ, Japan and the BIPM in accelerator photon beams

    NASA Astrophysics Data System (ADS)

    Picard, S.; Burns, D. T.; Roger, P.; Shimizu, M.; Morishita, Y.; Kato, M.; Tanaka, T.; Kurosawa, T.; Saito, N.

    2016-01-01

    A comparison of the dosimetry for accelerator photon beams was carried out between the National Metrology Institute of Japan (NMIJ) and the Bureau International des Poids et Mesures (BIPM) from 9 to 23 April 2015. The comparison was based on the determination of absorbed dose to water at 10 g cm-2 for three radiation qualities at the NMIJ. The results, reported as ratios of the NMIJ and the BIPM evaluations (and with the combined standard uncertainties given in parentheses), are 0.9966 (47) at 6 MV, 0.9965 (60) at 10 MV and 0.9953 (50) at 15 MV. This result is the eighth in the on-going BIPM.RI(I)-K6 series of comparisons. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCRI, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  2. Lessons Learned From CM-2 Modal Testing and Analysis

    NASA Technical Reports Server (NTRS)

    McNelis, Mark E.; Goodnight, Thomas W.; Carney, Kelly S.; Otten, Kim D.

    2002-01-01

    The Combustion Module-2 (CM-2) is a space experiment that launches on Shuttle mission STS-107 in the SPACEHAB Double Research Module. The CM-2 flight hardware is installed into SPACEHAB single and double racks. The CM-2 flight hardware was vibration tested in the launch configuration to characterize the structure's modal response. Cross-orthogonality between test and analysis mode shapes were used to assess model correlation. Lessons learned for pre-test planning and model verification are discussed.

  3. 32 CFR 10.8 - Amendment.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 1 2010-07-01 2010-07-01 false Amendment. 10.8 Section 10.8 National Defense Department of Defense OFFICE OF THE SECRETARY OF DEFENSE MILITARY COMMISSIONS MILITARY COMMISSION INSTRUCTIONS § 10.8 Amendment. The General Counsel may issue, supplement, amend, or revoke any...

  4. CM-2 Environmental / Modal Testing of Spacehab Racks

    NASA Technical Reports Server (NTRS)

    McNelis, Mark E.; Goodnight, Thomas W.; Farkas, Michael A.

    2001-01-01

    Combined environmental/modal vibration testing has been implemented at the NASA Glenn Research Center's Structural Dynamics Laboratory. The benefits of combined vibration testing are that it facilitates test article modal characterization and vibration qualification testing. The Combustion Module-2 (CM-2) is a space experiment that launches on Shuttle mission STS 107 in the SPACEHAB Research Double Module. The CM-2 flight hardware is integrated into a SPACEHAB single and double rack. CM-2 rack level combined vibration testing was recently completed on a shaker table to characterize the structure's modal response and verify the random vibration response. Control accelerometers and limit force gauges, located between the fixture and rack interface, were used to verify the input excitation. Results of the testing were used to verify the loads and environments for flight on the Shuttle.

  5. Benchmarking and performance analysis of the CM-2. [SIMD computer

    NASA Technical Reports Server (NTRS)

    Myers, David W.; Adams, George B., II

    1988-01-01

    A suite of benchmarking routines testing communication, basic arithmetic operations, and selected kernel algorithms written in LISP and PARIS was developed for the CM-2. Experiment runs are automated via a software framework that sequences individual tests, allowing for unattended overnight operation. Multiple measurements are made and treated statistically to generate well-characterized results from the noisy values given by cm:time. The results obtained provide a comparison with similar, but less extensive, testing done on a CM-1. Tests were chosen to aid the algorithmist in constructing fast, efficient, and correct code on the CM-2, as well as gain insight into what performance criteria are needed when evaluating parallel processing machines.

  6. 15 CFR 10.8 - Standing Committee.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... PRODUCT STANDARDS § 10.8 Standing Committee. (a) The Department shall establish and appoint the members of..., distributors, and users or consumers of the product covered by the standard, and representatives of appropriate...) The product or products covered by the standard; (2) The standard itself; and (3) Industry and...

  7. Microbiological study of the Murchison CM2 meteorite

    NASA Astrophysics Data System (ADS)

    Pikuta, Elena V.; Hoover, Richard B.

    2012-10-01

    In 1864, Louis Pasteur attempted to cultivate living microorganisms from pristine samples of the Orgueil CI1 carbonaceous meteorite. His results were negative and never published, but recorded it in his laboratory notebooks. At that time, only aerobic liquid or agar-based organic reach media were used, as his research on anaerobes had just started. In our laboratory the Murchison CM2 carbonaceous meteorite was selected to expand on these studies for microbiological study by cultivation on anaerobic mineral media. Since the surface could have been more easily contaminated, interior fragments of a sample of the Murchison meteorite were extracted and crushed under sterile conditions. The resulting powder was then mixed in anoxic medium and injected into Hungate tubes containing anaerobic media with various growth substrates at different pH and salinity and incubated at different temperatures. The goal of the experiments was to determine if living cells would grow from the material of freshly fractured interior fragments of the stone. If any growth occurred, work could then be carried out to assess the nature of the environmental contamination by observations of the culture growth (rates of speed and biodiversity); live/dead fluorescent staining to determine contamination level and DNA analysis to establish the microbial species present. In this paper we report the results of that study.

  8. Presolar grains in the CM2 chondrite Sutter's Mill

    NASA Astrophysics Data System (ADS)

    Zhao, Xuchao; Lin, Yangting; Yin, Qing-Zhu; Zhang, Jianchao; Hao, Jialong; Zolensky, Michael; Jenniskens, Peter

    2014-11-01

    The Sutter's Mill (SM) carbonaceous chondrite is a regolith breccia, composed predominantly of CM2 clasts with varying degrees of aqueous alteration and thermal metamorphism. An investigation of presolar grains in four Sutter's Mill sections, SM43, SM51, SM2-4, and SM18, was carried out using NanoSIMS ion mapping technique. A total of 37 C-anomalous grains and one O-anomalous grain have been identified, indicating an abundance of 63 ppm for presolar C-anomalous grains and 2 ppm for presolar oxides. Thirty-one silicon carbide (SiC), five carbonaceous grains, and one Al-oxide (Al2O3) were confirmed based on their elemental compositions determined by C-N-Si and O-Si-Mg-Al isotopic measurements. The overall abundance of SiC grains in Sutter's Mill (55 ppm) is consistent with those in other CM chondrites. The absence of presolar silicates in Sutter's Mill suggests that they were destroyed by aqueous alteration on the parent asteroid. Furthermore, SM2-4 shows heterogeneous distributions of presolar SiC grains (12-54 ppm) in different matrix areas, indicating that the fine-grained matrix clasts come from different sources, with various thermal histories, in the solar nebula.

  9. 24 CFR 10.8 - Notice of proposed rulemaking.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Notice of proposed rulemaking. 10.8 Section 10.8 Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development RULEMAKING: POLICY AND PROCEDURES Procedures § 10.8 Notice of proposed rulemaking. Each notice...

  10. Considerations for applying VARSKIN mod 2 to skin dose calculations averaged over 10 cm2.

    PubMed

    Durham, James S

    2004-02-01

    VARSKIN Mod 2 is a DOS-based computer program that calculates the dose to skin from beta and gamma contamination either directly on skin or on material in contact with skin. The default area for calculating the dose is 1 cm2. Recently, the U.S. Nuclear Regulatory Commission issued new guidelines for calculating shallow dose equivalent from skin contamination that requires the dose be averaged over 10 cm2. VARSKIN Mod 2 was not filly designed to calculate beta or gamma dose estimates averaged over 10 cm2, even though the program allows the user to calculate doses averaged over 10 cm2. This article explains why VARSKIN Mod 2 overestimates the beta dose when applied to 10 cm2 areas, describes a manual method for correcting the overestimate, and explains how to perform reasonable gamma dose calculations averaged over 10 cm2. The article also describes upgrades underway in Varskin 3. PMID:14744063

  11. Role of the CM2 Protein in the Influenza C Virus Replication Cycle ▿

    PubMed Central

    Furukawa, Takatoshi; Muraki, Yasushi; Noda, Takeshi; Takashita, Emi; Sho, Ri; Sugawara, Kanetsu; Matsuzaki, Yoko; Shimotai, Yoshitaka; Hongo, Seiji

    2011-01-01

    CM2 is the second membrane protein of influenza C virus. Although its biochemical characteristics, coding strategy, and properties as an ion channel have been extensively studied, the role(s) of CM2 in the virus replication cycle remains to be clarified. In order to elucidate this role, in the present study we generated CM2-deficient influenza C virus-like particles (VLPs) and examined the VLP-producing 293T cells, VLPs, and VLP-infected HMV-II cells. Quantification of viral RNA (vRNA) in the VLPs by real-time PCR revealed that the CM2-deficient VLPs contain approximately one-third of the vRNA found in wild-type VLPs although no significant differences were detected in the expression levels of viral components in VLP-producing cells or in the number and morphology of the generated VLPs. This finding suggests that CM2 is involved in the genome packaging process into VLPs. Furthermore, HMV-II cells infected with CM2-deficient VLPs exhibited significantly reduced reporter gene expression. Although CM2-deficient VLPs could be internalized into HMV-II cells as efficiently as wild-type VLPs, a smaller amount of vRNA was detected in the nuclear fraction of CM2-deficient VLP-infected cells than in that of wild-type VLP-infected cells, suggesting that the uncoating process of the CM2-deficient VLPs in the infected cells did not proceed in an appropriate manner. Taken together, the data obtained in the present study indicate that CM2 has a potential role in the genome packaging and uncoating processes of the virus replication cycle. PMID:21106743

  12. Multielectron ultrastrong laser field ionization of Arn+, Krm+ and Xel+ (n <= 9, m <= 9, l <= 12) at intensities from 1015 W cm-2 to 1018 W cm-2

    NASA Astrophysics Data System (ADS)

    Palaniyappan, S.; Di Chiara, A.; Ghebregziabher, I.; Huskins, E. L.; Falkowski, A.; Pajerowski, D.; Walker, B. C.

    2006-07-01

    Ionization yields are reported for Ar, Kr and Xe in ultrastrong fields from 1015 W cm-2 to 1018 W cm-2. Non-sequential ionization (NSI) is shown to be a robust and general feature in ultrahigh field ionization. NSI yields measured are consistent with the trends predicted by a rescattering model, but as one proceeds to higher Z atoms more NSI is observed than predicted theoretically. Additional recollision mechanisms that may need to be considered in future theories of ultrastrong field-atom interactions include 'chain' NSI, NSI from excited states of the atom (e.g. Rydberg states or inner-shell holes) and the possibility of ultrastrong field enhanced recollision/impact processes.

  13. Development and characterization of a 280 cm2 vanadium/oxygen fuel cell

    NASA Astrophysics Data System (ADS)

    Noack, Jens; Cremers, Carsten; Bayer, Domnik; Tübke, Jens; Pinkwart, Karsten

    2014-05-01

    A vanadium/oxygen fuel cell with an active area of 280 cm2 has been developed. The cell consisted of two membranes with two half-cells and an intermediate chamber. The maximum achieved power density was 23 mW cm-2 at 0.56 V with lambda air = 3 and a 1.6 M V2+ solution at room temperature. The average discharge power density was 19.6 mW cm-2 at a constant current density of 40 mA cm-2 with an average voltage efficiency of 33%. The fuel based energy density was 18.2% of the theoretical value with 11.8 Wh L-1. In comparison with a similarly constructed 50 cm2 cell, both achieved similar performance levels. An analysis using the half-cell potential profiles and by means of impedance spectroscopy revealed that, as for the 50 cm2 cell, the low rate of oxygen reduction reaction significantly affected the performance of the cell. Thus gives potential for the optimization of the cathode reaction and a reduction in the ohmic resistances potential for higher power densities.

  14. GFDL's CM2 global coupled climate models. Part I: Formulation and simulation characteristics

    USGS Publications Warehouse

    Delworth, T.L.; Broccoli, A.J.; Rosati, A.; Stouffer, R.J.; Balaji, V.; Beesley, J.A.; Cooke, W.F.; Dixon, K.W.; Dunne, J.; Dunne, K.A.; Durachta, J.W.; Findell, K.L.; Ginoux, P.; Gnanadesikan, A.; Gordon, C.T.; Griffies, S.M.; Gudgel, R.; Harrison, M.J.; Held, I.M.; Hemler, R.S.; Horowitz, L.W.; Klein, S.A.; Knutson, T.R.; Kushner, P.J.; Langenhorst, A.R.; Lee, H.-C.; Lin, S.-J.; Lu, J.; Malyshev, S.L.; Milly, P.C.D.; Ramaswamy, V.; Russell, J.; Schwarzkopf, M.D.; Shevliakova, E.; Sirutis, J.J.; Spelman, M.J.; Stern, W.F.; Winton, M.; Wittenberg, A.T.; Wyman, B.; Zeng, F.; Zhang, R.

    2006-01-01

    The formulation and simulation characteristics of two new global coupled climate models developed at NOAA's Geophysical Fluid Dynamics Laboratory (GFDL) are described. The models were designed to simulate atmospheric and oceanic climate and variability from the diurnal time scale through multicentury climate change, given our computational constraints. In particular, an important goal was to use the same model for both experimental seasonal to interannual forecasting and the study of multicentury global climate change, and this goal has been achieved. Tw o versions of the coupled model are described, called CM2.0 and CM2.1. The versions differ primarily in the dynamical core used in the atmospheric component, along with the cloud tuning and some details of the land and ocean components. For both coupled models, the resolution of the land and atmospheric components is 2?? latitude ?? 2.5?? longitude; the atmospheric model has 24 vertical levels. The ocean resolution is 1?? in latitude and longitude, with meridional resolution equatorward of 30?? becoming progressively finer, such that the meridional resolution is 1/3?? at the equator. There are 50 vertical levels in the ocean, with 22 evenly spaced levels within the top 220 m. The ocean component has poles over North America and Eurasia to avoid polar filtering. Neither coupled model employs flux adjustments. The co ntrol simulations have stable, realistic climates when integrated over multiple centuries. Both models have simulations of ENSO that are substantially improved relative to previous GFDL coupled models. The CM2.0 model has been further evaluated as an ENSO forecast model and has good skill (CM2.1 has not been evaluated as an ENSO forecast model). Generally reduced temperature and salinity biases exist in CM2.1 relative to CM2.0. These reductions are associated with 1) improved simulations of surface wind stress in CM2.1 and associated changes in oceanic gyre circulations; 2) changes in cloud tuning and

  15. 28 CFR 10.8 - Information to be kept current.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 28 Judicial Administration 1 2013-07-01 2013-07-01 false Information to be kept current. 10.8... kept current. A supplemental statement must be filed with the Attorney General within thirty days after... information and documents previously filed accurate and current with respect to the preceding six...

  16. 28 CFR 10.8 - Information to be kept current.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Information to be kept current. 10.8... kept current. A supplemental statement must be filed with the Attorney General within thirty days after... information and documents previously filed accurate and current with respect to the preceding six...

  17. 28 CFR 10.8 - Information to be kept current.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 28 Judicial Administration 1 2011-07-01 2011-07-01 false Information to be kept current. 10.8... kept current. A supplemental statement must be filed with the Attorney General within thirty days after... information and documents previously filed accurate and current with respect to the preceding six...

  18. 28 CFR 10.8 - Information to be kept current.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 28 Judicial Administration 1 2012-07-01 2012-07-01 false Information to be kept current. 10.8... kept current. A supplemental statement must be filed with the Attorney General within thirty days after... information and documents previously filed accurate and current with respect to the preceding six...

  19. 28 CFR 10.8 - Information to be kept current.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 28 Judicial Administration 1 2014-07-01 2014-07-01 false Information to be kept current. 10.8... kept current. A supplemental statement must be filed with the Attorney General within thirty days after... information and documents previously filed accurate and current with respect to the preceding six...

  20. CM2 antigen, a potential novel molecule participating in glucuronide transport on rat hepatocyte canalicular membrane.

    PubMed

    Wang, L; Wang, J; Zhou, X; Li, J; Shi, Y; Han, Z; Wang, X; Li, S; Yang, Z; Wang, R; Fan, D; Han, Y

    2012-06-29

    The polarized molecules predominately distributing at hepatocyte canalicular surface play a vital role in disclosing the process of bile formation and etiopathogenisis of cholestatic live diseases. Therefore, it is important to find novel polarized molecules on hepatocyte canalicular membrane. In the present study, canalicular membrane vesicles (CMVs) isolated from rat hepatocyte by density gradient centrifugation were used as immunogens to produce hybridoma and 46 strains of monoclonal antibodies (mAb) against CMVs were obtained. With a series of morphological assay methods, including immunohistochemistry, immunofluorescence and immuno-electron microscope, the antigens recognized by canalicular mAb1 (CM1) and canalicular mAb2 (CM2) were confirmed to predominately distribute at hepatocyte canalicular membrane. Transport activity assay revealed that CM2 could inhibit ATP-dependent E217βG uptake of rat hepatocyte CMVs. Meanwhile, Western blotting analysis showed that the molecular mass of CM2 antigen was approximately 110kDa, which was much less than Mr 180kDa of multidrug resistance-associated protein 2 (MRP2) involved in glucuronide transport. These data indicated that CM2 antigen might be a potential novel molecule participating in glucuronide transport on the hepatocyte canalicular membrane.

  1. Aliphatic amines in Antarctic CR2, CM2, and CM1/2 carbonaceous chondrites

    NASA Astrophysics Data System (ADS)

    Aponte, José C.; McLain, Hannah L.; Dworkin, Jason P.; Elsila, Jamie E.

    2016-09-01

    Meteoritic water-soluble organic compounds provide a unique record of the processes that occurred during the formation of the solar system and the chemistry preceding the origins of life on Earth. We have investigated the molecular distribution, compound-specific δ13C isotopic ratios and enantiomeric compositions of aliphatic monoamines present in the hot acid-water extracts of the carbonaceous chondrites LAP 02342 (CR2), GRA 95229 (CR2), LON 94101 (CM2), LEW 90500 (CM2), and ALH 83100 (CM1/2). Analyses of the concentration of monoamines in these meteorites revealed: (a) the CR2 chondrites studied here contain higher concentrations of monoamines relative to the analyzed CM2 chondrites; (b) the concentration of monoamines decreases with increasing carbon number; and (c) isopropylamine is the most abundant monoamine in these CR2 chondrites, while methylamine is the most abundant amine species in these CM2 and CM1/2 chondrites. The δ13C values of monoamines in CR2 chondrite do not correlate with the number of carbon atoms; however, in CM2 and CM1/2 chondrites, the 13C enrichment decreases with increasing monoamine carbon number. The δ13C values of methylamine in CR2 chondrites ranged from -1 to +10‰, while in CM2 and CM1/2 chondrites the δ13C values of methylamine ranged from +41 to +59‰. We also observed racemic compositions of sec-butylamine, 3-methyl-2-butylamine, and sec-pentylamine in the studied carbonaceous chondrites. Additionally, we compared the abundance and δ13C isotopic composition of monoamines to those of their structurally related amino acids. We found that monoamines are less abundant than amino acids in CR2 chondrites, with the opposite being true in CM2 and CM1/2 chondrites. We used these collective data to evaluate different primordial synthetic pathways for monoamines in carbonaceous chondrites and to understand the potential common origins these molecules may share with meteoritic amino acids.

  2. The EET87513 clast N: A CM2 fragment in an HED polymict breccia

    NASA Technical Reports Server (NTRS)

    Buchanan, P. C.; Zolensky, M. E.; Reid, A. M.; Barrett, R. A.

    1993-01-01

    Xenoliths of material resembling carbonaceous chondrites have been found in several HED polymict breccias. Most workers concluded that these clasts are related to CM2 meteorites on the basis of texture, bulk composition, and mineralogy. Data on clast N, a carbonaceous chondrite fragment from the howardite EET87513 large enough (approximately 4x5mm on the surface of the slab from which it was separated) to extract bulk samples for INAA and oxygen isotope analysis and to provide a thin section for electron microprobe, SEM, and TEM analysis is reported. Preliminary data for this clast were previously reported. INAA was performed at Oregon State University and bulk oxygen isotopic composition was determined at the University of Chicago. These data confirm that EET87513 clast N is a fragment of CM2 material.

  3. Investigation of pyridine carboxylic acids in CM2 carbonaceous chondrites: Potential precursor molecules for ancient coenzymes

    NASA Astrophysics Data System (ADS)

    Smith, Karen E.; Callahan, Michael P.; Gerakines, Perry A.; Dworkin, Jason P.; House, Christopher H.

    2014-07-01

    The distribution and abundances of pyridine carboxylic acids (including nicotinic acid) in eight CM2 carbonaceous chondrites (ALH 85013, DOM 03183, DOM 08003, EET 96016, LAP 02333, LAP 02336, LEW 85311, and WIS 91600) were investigated by liquid chromatography coupled to UV detection and high resolution Orbitrap mass spectrometry. We find that pyridine monocarboxylic acids are prevalent in CM2-type chondrites and their abundance negatively correlates with the degree of pre-terrestrial aqueous alteration that the meteorite parent body experienced. We also report the first detection of pyridine dicarboxylic acids in carbonaceous chondrites. Additionally, we carried out laboratory studies of proton-irradiated pyridine in carbon dioxide-rich ices (a 1:1 mixture) to serve as a model of the interstellar ice chemistry that may have led to the synthesis of pyridine carboxylic acids. Analysis of the irradiated ice residue shows that a comparable suite of pyridine mono- and dicarboxylic acids was produced, although aqueous alteration may still play a role in the synthesis (and ultimate yield) of these compounds in carbonaceous meteorites. Nicotinic acid is a precursor to nicotinamide adenine dinucleotide, a likely ancient molecule used in cellular metabolism in all of life, and its common occurrence in CM2 chondrites may indicate that meteorites may have been a source of molecules for the emergence of more complex coenzymes on the early Earth.

  4. Investigation of Pyridine Carboxylic Acids in CM2 Carbonaceous Chondrites: Potential Precursor Molecules for Ancient Coenzymes

    NASA Technical Reports Server (NTRS)

    Smith, Karen E.; Callahan, Michael P.; Gerakines, Perry A.; Dworkin, Jason P.; House, Christopher H.

    2014-01-01

    The distribution and abundances of pyridine carboxylic acids (including nicotinic acid) in eight CM2 carbonaceous chondrites (ALH 85013, DOM 03183, DOM 08003, EET 96016, LAP 02333, LAP 02336, LEW 85311, and WIS 91600) were investigated by liquid chromatography coupled to UV detection and high resolution Orbitrap mass spectrometry. We find that pyridine monocarboxylic acids are prevalent in CM2-type chondrites and their abundance negatively correlates with the degree of pre-terrestrial aqueous alteration that the meteorite parent body experienced. We lso report the first detection of pyridine dicarboxylic acids in carbonaceous chondrites. Additionally, we carried out laboratory studies of proton-irradiated pyridine in carbon dioxide-rich ices (a 1:1 mixture) to serve as a model of the interstellar ice chemistry that may have led to the synthesis of pyridine carboxylic acids. Analysis of the irradiated ice residue shows that a comparable suite of pyridine mono- and dicarboxylic acids was produced, although aqueous alteration may still play a role in the synthesis (and ultimate yield) of these compounds in carbonaceous meteorites. Nicotinic acid is a precursor to nicotinamide adenine dinucleotide, a likely ancient molecule used in cellular metabolism in all of life, and its common occurrence in CM2 chondrites may indicate that meteorites may have been a source of molecules for the emergence of more complex coenzymes on the early Earth.

  5. Investigation of Pyridine Carboxylic Acids in CM2 Carbonaceous Chondrites: Potential Precursor Molecules for Ancient Coenzymes

    NASA Technical Reports Server (NTRS)

    Smith, Karen E.; Callahan, Michael P.; Gerakines, Perry A.; Dworkin, Jason P.; House, Christopher H.

    2014-01-01

    The distribution and abundances of pyridine carboxylic acids (including nicotinic acid) in eight CM2 carbonaceous chondrites (ALH 85013, DOM 03183, DOM 08003, EET 96016, LAP 02333, LAP 02336, LEW 85311, and WIS 91600) were investigated by liquid chromatography coupled to UV detection and high resolution Orbitrap mass spectrometry. We find that pyridine monocarboxylic acids are prevalent in CM2-type chondrites and their abundance negatively correlates with the degree of pre-terrestrial aqueous alteration that the meteorite parent body experienced. We also report the first detection of pyridine dicarboxylic acids in carbonaceous chondrites. Additionally, we carried out laboratory studies of proton-irradiated pyridine in carbon dioxide-rich ices (a 1:1 mixture) to serve as a model of the interstellar ice chemistry that may have led to the synthesis of pyridine carboxylic acids. Analysis of the irradiated ice residue shows that a comparable suite of pyridine mono- and dicarboxylic acids was produced, although aqueous alteration may still play a role in the synthesis (and ultimate yield) of these compounds in carbonaceous meteorites. Nicotinic acid is a precursor to nicotinamide adenine dinucleotide, a likely ancient molecule used in cellular metabolism in all of life, and its common occurrence in CM2 chondrites may indicate that meteorites may have been a source of molecules for the emergence of more complex coenzymes on the early Earth.

  6. Experimental investigation of a 1 kA/cm2 sheet beam plasma cathode electron gun

    NASA Astrophysics Data System (ADS)

    Kumar, Niraj; Narayan Pal, Udit; Kumar Pal, Dharmendra; Prajesh, Rahul; Prakash, Ram

    2015-01-01

    In this paper, a cold cathode based sheet-beam plasma cathode electron gun is reported with achieved sheet-beam current density ˜1 kA/cm2 from pseudospark based argon plasma for pulse length of ˜200 ns in a single shot experiment. For the qualitative assessment of the sheet-beam, an arrangement of three isolated metallic-sheets is proposed. The actual shape and size of the sheet-electron-beam are obtained through a non-conventional method by proposing a dielectric charging technique and scanning electron microscope based imaging. As distinct from the earlier developed sheet beam sources, the generated sheet-beam has been propagated more than 190 mm distance in a drift space region maintaining sheet structure without assistance of any external magnetic field.

  7. Actinic defect counting statistics over 1 cm2 area of EUVL mask blank

    SciTech Connect

    Jeong, Seongtae; Lai, Chih-Wei; Rekawa, Seno; Walton, Chris W.; Bokor, Jeffrey

    2000-02-18

    As a continuation of comparison experiments between EUV inspection and visible inspection of defects on EUVL mask blanks, we report on the result of an experiment where the EUV defect inspection tool is used to perform at-wavelength defect counting over 1 cm{sup 2} of EUVL mask blank. Initial EUV inspection found five defects over the scanned area and the subsequent optical scattering inspection was able to detect all of the five defects. Therefore, if there are any defects that are only detectable by EUV inspection, the density is lower than the order of unity per cm2. An upgrade path to substantially increase the overall throughput of the EUV inspection system is also identified in the manuscript.

  8. Vibration Energy Harvesting Characterization of 1 cm2 Poly(vinylidene fluoride) Generators in Vacuum

    NASA Astrophysics Data System (ADS)

    Cao, Ziping; Zhang, Jinya; Kuwano, Hiroki

    2011-09-01

    In this study, poly(vinylidene fluoride) (PVDF) was used as a piezoelectric element to fabricate small size (two-dimensional area <1 cm2) generators with low resonant frequency (about 100 Hz) for matching the frequency of vibration sources. To clarify the effect of the air damping on the vibration energy harvesting, PVDF generators were investigated in three measurement conditions: “unpackaged in air”, “packaged in air”, and “unpackaged in vacuum”. It was found that the output power of generators “unpackaged in vacuum” was almost twice that of generators “packaged in air” at 0.5g acceleration. With the increase in vibration acceleration, the output power of generators “unpackaged in vacuum” rapidly increased in a quadratic relationship with the acceleration at low acceleration level, and then the increasing ratio decreased at high acceleration. At 4.31g acceleration, the output power reached 100.833 µW.

  9. Compositions of Partly Altered Olivine and Replacement Serpentine in the CM2 Chondrite QUE93005

    NASA Technical Reports Server (NTRS)

    Velbel, M. A.; Tonui, E. K.; Zolensky, M. E.

    2005-01-01

    Some phyllosilicates in CM carbonaceous chondrites formed by aqueous alteration of anhydrous precursor phases. Although broad trends in the compositions of hydrous phyllosilicates are recognized and believed to be related to trends in degree of aqueous alteration, details of the reactions that formed specific secondary minerals remain obscure. This paper reports compositional relationships between remnants of partially pseudomorphically (or alteromorphically) replaced silicates and their alteration products (serpentine) in the CM2 chondrite QUE93005 and compares it with previously published results for ALH81002. Reactants and products were characterized by optical petrography, backscattered scanning electron microscopy (BSEM), and electron microprobe. By focusing on serpentine formed from known reactants (olivines), and on only those instances in which some of the reactant silicate remains, direct compositional relationships between reactants and products, and the elemental mobility required by the reactions, can be established. Additional information is included in the original extended abstract.

  10. Organic blend semiconductors and transistors with hole mobility exceeding 10 cm2/Vs (Presentation Recording)

    NASA Astrophysics Data System (ADS)

    Paterson, Alexandra F.; Anthopoulos, Thomas D.

    2015-10-01

    Plastic electronics that can be manufactured using solution-based methods are the subject of great research interest due to their potential for low-cost, large-area electronic applications. The interest in this field has led to considerable research and subsequent advances in device performance. To this end solution-processed organic thin-film transistors (OTFTs) have shown impressive improvements in recent years through the increasing values of charge carrier mobility. Here we report the development of next generation organic blend materials for OTFTs with hole mobilities of 10 cm2/Vs. These high performance devices have been achieved using a novel semiconducting blend system comprising of an amorphous-like conjugated polymer and a high mobility small molecule. The combination of a highly crystalline small molecule with the polymer binder aids the formation of uniform films as well as enables an element of control over the nucleation and growth of the small molecule. The polymer binders investigated belongs to the family of indacenodithiophene-based copolymers which are renowned for their high carrier mobilities regardless of their apparent structural disorder. The addition of the polymer with carefully chosen small molecules is found to further increase the hole mobility of the resulting blend OTFT to over 10 cm2/Vs. These organic devices provide an interesting insight into this rather complex blend system, highlighting the correlation between the morphology developed following solution processing and device performance, as well as exploring the role of each of the two components in the blend in terms of their contribution to charge transport.

  11. Spectral content of buried Ag foils at 1016 W/cm2 laser illuminationa)

    NASA Astrophysics Data System (ADS)

    Huntington, C. M.; Maddox, B. R.; Park, H.-S.; Prisbrey, S.; Remington, B. A.

    2014-11-01

    Sources of 5-12 keV thermal Heα x-rays are readily generated by laser irradiation of mid-Z foils at intensities >1014 W/cm2, and are widely used as probes for inertial confinement fusion and high-energy-density experiments. Higher energy 17-50 keV x-ray sources are efficiently produced from "cold" Kα emission using short pulse, petawatt lasers at intensities >1018 W/cm2 [H.-S. Park, B. R. Maddox et al., "High-resolution 17-75 keV backlighters for high energy density experiments," Phys. Plasmas 15(7), 072705 (2008); B. R. Maddox, H. S. Park, B. A. Remington et al., "Absolute measurements of x-ray backlighter sources at energies above 10 keV," Phys. Plasmas 18(5), 056709 (2011)]. However, when long pulse (>1 ns) lasers are used with Z > 30 elements, the spectrum contains contributions from both K shell transitions and from ionized atomic states. Here we show that by sandwiching a silver foil between layers of high-density carbon, the ratio of Kα:Heα in the x-ray spectrum is significant increased over directly illuminated Ag foils, with narrower lines from K-shell transitions. Additionally, the emission volume is more localized for the sandwiched target, producing a more planar x-ray sheet. This technique may be useful for generating probes requiring spectral purity and a limited spatial extent, for example, in incoherent x-ray Thomson scattering experiments.

  12. The amino acid composition of the Sutter's Mill CM2 carbonaceous chondrite

    NASA Astrophysics Data System (ADS)

    Burton, Aaron S.; Glavin, Daniel P.; Elsila, Jamie E.; Dworkin, Jason P.; Jenniskens, Peter; Yin, Qing-Zhu

    2014-11-01

    We determined the abundances and enantiomeric compositions of amino acids in Sutter's Mill fragment #2 (designated SM2) recovered prior to heavy rains that fell April 25-26, 2012, and two other meteorite fragments, SM12 and SM51, that were recovered postrain. We also determined the abundance, enantiomeric, and isotopic compositions of amino acids in soil from the recovery site of fragment SM51. The three meteorite stones experienced terrestrial amino acid contamination, as evidenced by the low D/L ratios of several proteinogenic amino acids. The D/L ratios were higher in SM2 than in SM12 and SM51, consistent with rain introducing additional L-amino acid contaminants to SM12 and SM51. Higher percentages of glycine, β-alanine, and γ-amino-n-butyric acid were observed in free form in SM2 and SM51 compared with the soil, suggesting that these free amino acids may be indigenous. Trace levels of D+L-β-aminoisobutyric acid (β-AIB) observed in all three meteorites are not easily explained as terrestrial contamination, as β-AIB is rare on Earth and was not detected in the soil. Bulk carbon and nitrogen and isotopic ratios of the SM samples and the soil also indicate terrestrial contamination, as does compound-specific isotopic analysis of the amino acids in the soil. The amino acid abundances in SM2, the most pristine SM meteorite analyzed here, are approximately 20-fold lower than in the Murchison CM2 carbonaceous chondrite. This may be due to thermal metamorphism in the Sutter's Mill parent body at temperatures greater than observed for other aqueously altered CM2 meteorites.

  13. A minimum column density of 1 g cm(-2) for massive star formation.

    PubMed

    Krumholz, Mark R; McKee, Christopher F

    2008-02-28

    Massive stars are very rare, but their extreme luminosities make them both the only type of young star we can observe in distant galaxies and the dominant energy sources in the Universe today. They form rarely because efficient radiative cooling keeps most star--forming gas clouds close to isothermal as they collapse, and this favours fragmentation into stars of one solar mass or lower. Heating of a cloud by accreting low-mass stars within it can prevent fragmentation and allow formation of massive stars, but the necessary properties for a cloud to form massive stars-and therefore where massive stars form in a galaxy--have not yet been determined. Here we show that only clouds with column densities of at least 1 g cm(-2) can avoid fragmentation and form massive stars. This threshold, and the environmental variation of the stellar initial mass function that it implies, naturally explain the characteristic column densities associated with massive star clusters and the difference between the radial profiles of Halpha and ultraviolet emission in galactic disks. The existence of a threshold also implies that the initial mass function should show detectable variation with environment within the Galaxy, that the characteristic column densities of clusters containing massive stars should vary between galaxies, and that star formation rates in some galactic environments may have been systematically underestimated.

  14. On the Behavior of Phosphorus During the Aqueous Alteration of CM2 Carbonaceous Chondrites

    NASA Technical Reports Server (NTRS)

    Brearley, Adrian J.; Chizmadia, Lysa J.

    2005-01-01

    During the earliest period of solar system formation, water played an important role in the evolution of primitive dust, both after accretion of planetesimals and possible before accretion within the protoplanetary disk. Many chondrites show evidence of variable degrees of aqueous alteration, the CM2 chondrites being among the most studied [1]. This group of chondrites is characterized by mineral assemblages of both primary and secondary alteration phases. Hence, these meteorites retain a particularly important record of the reactions that occurred between primary high temperature nebular phases and water. Studies of these chondrites can provide information on the conditions and environments of aqueous alteration and the mobility of elements during alteration. This latter question is at the core of a debate concerning the location of aqueous alteration, i.e. whether alteration occurred predominantly within a closed system after accretion (parent body alteration) or whether some degree of alteration occurred within the solar nebula or on ephemeral protoplanetary bodies prior to accretion. At the core of the parent body alteration model is the hypothesis that elemental exchange between different components, principally chondrules and matrix, must have occurred. chondrules and matrix, must have occurred. In this study, we focus on the behavior of the minor element, phosphorus. This study was stimulated by observations of the behavior of P during the earliest stages of alteration in glassy mesostasis in type II chondrules in CR chondrites and extends the preliminary observations of on Y791198 to other CM chondrites.

  15. N-15-Rich Organic Globules in a Cluster IDP and the Bells CM2 Chondrite

    NASA Technical Reports Server (NTRS)

    Messenger, S.; Nakamura-Messenger, K.; Keller, Lindsay P.

    2008-01-01

    Organic matter in primitive meteorites and chondritic porous interplanetary dust particles (CP IDPs) is commonly enriched in D/H and 15N/14N relative to terrestrial values [1-3]. These anomalies are ascribed to the partial preservation of presolar cold molecular cloud material [1]. Some meteorites and IDPs contain m-size inclusions with extreme H and N isotopic anomalies [2-4], possibly due to preserved pristine primordial organic grains. We recently showed that the in the Tagish Lake meteorite, the principle carriers of these anomalies are sub- m, hollow organic globules [5]. The globules likely formed by photochemical processing of organic ices in a cold molecular cloud or the outermost regions of the protosolar disk [5]. We proposed that similar materials should be common among primitive meteorites, IDPs, and comets. Similar objects have been observed in organic extracts of carbonaceous chondrites [6-8], however their N and H isotopic compositions are generally unknown. Bulk H and N isotopic compositions may indicate which meteorites best preserve interstellar organic compounds. Thus, we selected the Bells CM2 carbonaceous chondrites for study based on its large bulk 15N (+335 %) and D (+990 %) [9].

  16. Fe and O EELS Studies of Ion Irradiated Murchison CM2 Carbonaceous Chondrite Matrix

    NASA Technical Reports Server (NTRS)

    Keller, L. P.; Christofferson, R.; Dukes, C. A.; Baragiola, R. A.; Rahman, Z.

    2015-01-01

    Introduction: The physical and chemical response of hydrated carbonaceous chondrite materials to space weathering processes is poorly understood. Improving this understanding is a key part of establishing how regoliths on primitive carbonaceous asteroids respond to space weathering processes, knowledge that supports future sample return missions (Hayabusa 2 and OSIRISREx) that are targeting objects of this type. We previously reported on He+ irradiation of Murchison matrix and showed that the irradiation resulted in amorphization of the matrix phyllosilicates, loss of OH, and surface vesiculation. Here, we report electron energy-loss spectroscopy (EELS) measurements of the irradiated material with emphasis on the Fe and O speciation. Sample and Methods: A polished thin section of the Murchison CM2 carbonaceous chondrite was irradiated with 4 kilovolts He(+) (normal incidence) to a total dose of 1 x 10(exp 18) He(+) per square centimeter. We extracted thin sections from both irradiated and unirradiated regions in matrix using focused ion beam (FIB) techniques with electron beam deposition for the protective carbon strap to minimize surface damage artifacts from the FIB milling. The FIB sections were analyzed using a JEOL 2500SE scanning and transmission electron microscope (STEM) equipped with a Gatan Tridiem imaging filter. EELS spectra were collected from 50 nanometer diameter regions with an energy resolution of 0.7 electronvolts FWHM at the zero loss. EELS spectra were collected at low electron doses to minimize possible artifacts from electron-beam irradiation damage. Results and Discussion: Fe L (sub 2,3) EELS spectra from matrix phyllosilicates in CM chondrites show mixed Fe(2+)/Fe(3+) oxidation states with Fe(3+)/Sigma Fe approximately 0.5. Fe L(sub 2,3) spectra from the irradiated/ amorphized matrix phyllosilicates show higher Fe(2+)/Fe(3+) ratios compared to spectra obtained from pristine material at depths beyond the implantation/amorphization layer. We

  17. Formation of spinel-, hibonite-rich inclusions found in CM2 carbonaceous chrondrites

    SciTech Connect

    Simon, S B; Grossman, L; Hutcheon, I D; Phinney, D L; Weber, P K; Fallon, S J

    2005-11-03

    We report petrography, mineral chemistry, bulk chemistry, and bulk isotopic compositions of a suite of 40 spinel-rich inclusions from the Murchison (CM2) carbonaceous chondrite. Seven types of inclusions are identified based on mineralogy: spinel-hibonite-perovskite; spinel-perovskite-pyroxene; spinel-perovskite-melilite; spinel-hibonite-perovskite-melilite; spinel-hibonite; spinel-pyroxene; and spinel-melilite-anorthite. Hibonite-bearing inclusions have Ti-poor spinel compared to the hibonite-free ones, and spinel-hibonite-perovskite inclusions have the highest average bulk TiO{sub 2} contents (7.8 wt%). The bulk CaO/Al{sub 2}O{sub 3} ratios of the inclusions range from 0.005-0.21, well below the solar value of 0.79. Hibonite-, spinel-rich inclusions consist of phases that are not predicted by condensation calculations to coexist; in the equilibrium sequence, hibonite is followed by melilite, which is followed by spinel. Therefore, hibonite-melilite or melilite-spinel inclusions should be dominant instead. One explanation for the 'missing melilite' is that it condensed as expected but was lost due to evaporation of Mg and Ca during heating and melting of spherule precursors. If this theory were correct, melilite-poor spherules would have isotopically heavy Mg and Ca. Except for one inclusion with F{sub Mg} = 4.3 {+-} 2.6{per_thousand}/amu and another with isotopically light Ca (F{sub Ca} = 3.4 {+-} 2.0{per_thousand}/amu), however, all the inclusions we analyzed have normal isotopic compositions within their 2{sigma} uncertainties. Thus, we found no evidence for significant mass-dependent fractionation. Our preferred explanation for the general lack of melilite among hibonite-, spinel-bearing inclusions is kinetic inhibition of melilite condensation relative to spinel. Because of similarities between the crystal structures of hibonite and spinel, it should be easier for spinel to form from hibonite than for melilite to do so.

  18. Impact-Induced Chondrule Deformation and Aqueous Alteration of CM2 Murchison

    NASA Technical Reports Server (NTRS)

    Hanna, R. D.; Zolensky, M.; Ketcham, R. A.; Behr, W. M.; Martinez, J. E.

    2014-01-01

    Deformed chondrules in CM2 Murchison have been found to define a prominent foliation [1,2] and lineation [3] in 3D using X-ray computed tomography (XCT). It has been hypothesized that chondrules in foliated chondrites deform by "squeezing" into surrounding pore space [4,5], a process that also likely removes primary porosity [6]. However, shock stage classification based on olivine extinction in Murchison is consistently low (S1-S2) [4-5,7] implying that significant intracrystalline plastic deformation of olivine has not occurred. One objective of our study is therefore to determine the microstructural mechanisms and phases that are accommodating the impact stress and resulting in relative displacements within the chondrules. Another question regarding impact deformation in Murchison is whether it facilitated aqueous alteration as has been proposed for the CMs which generally show a positive correlation between degree of alteration and petrofabric strength [7,2]. As pointed out by [2], CM Murchison represents a unique counterpoint to this correlation: it has a strong petrofabric but a relatively low degree of aqueous alteration. However, Murchison may not represent an inconsistency to the proposed causal relationship between impact and alteration, if it can be established that the incipient aqueous alteration post-dated chondrule deformation. Methods: Two thin sections from Murchison sample USNM 5487 were cut approximately perpendicular to the foliation and parallel to lineation determined by XCT [1,3] and one section was additionally polished for EBSD. Using a combination of optical petrography, SEM, EDS, and EBSD several chondrules were characterized in detail to: determine phases, find microstructures indicative of strain, document the geometric relationships between grain-scale microstructures and the foliation and lineation direction, and look for textural relationships of alteration minerals (tochilinite and Mg-Fe serpentine) that indicate timing of their

  19. Nanoimprinted polymer lasers with threshold below 100 W/cm2 using mixed-order distributed feedback resonators.

    PubMed

    Wang, Yue; Tsiminis, Georgios; Kanibolotsky, Alexander L; Skabara, Peter J; Samuel, Ifor D W; Turnbull, Graham A

    2013-06-17

    Organic semiconductor lasers were fabricated by UV-nanoimprint lithography with thresholds as low as 57 W/cm(2) under 4 ns pulsed operation. The nanoimprinted lasers employed mixed-order distributed feedback resonators, with second-order gratings surrounded by first-order gratings, combined with a light-emitting conjugated polymer. They were pumped by InGaN LEDs to produce green-emitting lasers, with thresholds of 208 W/cm(2) (102 nJ/pulse). These hybrid lasers incorporate a scalable UV-nanoimprint lithography process, compatible with high-performance LEDs, therefore we have demonstrated a coherent, compact, low-cost light source.

  20. Comparison of visible and near-infrared reflectance spectra of CM2 carbonaceous chondrites and primitive asteroids

    NASA Technical Reports Server (NTRS)

    Vilas, F.; Hiroi, T.; Zolensky, M. E.

    1993-01-01

    Spectra of primitive asteroids (defined as C, P, and D classes and associated subclasses) were compared to the limited number of spectra of CM2 carbonaceous chondrites. An absorption feature located at 0.7 microns attributed to an Fe(+2) - Fe(+3) charge transfer absorption in iron oxides in phyllosilicates is apparent in some of the CM2 carbonaceous chondrite spectra and many of the asteroid spectra. Sawyer found a correlation between the area of the 0.7 micron feature and the mean semimajor axis of the asteroids. Spectra of a larger sample of carbonaceous chondrites, including 7 CM2 chondrites, covering a spectral interval of 0.30-2.5 microns were recently obtained using the Relab instrument at Brown University. These spectra were compared with spectrophotometric asteroid observations in a separate abstract. Those spectra of CM2 chondrites were isolated into the UV, visible and near-infrared spectral regions in order to compare them with high-quality narrowband reflectance spectra.

  1. Successful Capture, Extraction and Identification of Hypervelocity CM2 Meteorite Fragments Shot by Light-Gas Gun

    NASA Technical Reports Server (NTRS)

    Snead, C.; Westphal, A. J.; Dominguez, G.; Zolensky, M. E.

    2003-01-01

    Here we report the successful capture, extraction and identification of two fragments of a CM2 meteorite (ALH83100) into lowdensity aerogel. The shot was carried out at the AVGR at NASAARC. A mixture of powdered ALH83100 and borosilicate glass microspheres was shot at 4.55.0 km/sec into 50 mg cm silicate aerogel.

  2. Design of photon converter and photoneutron target for High power electron accelerator based BNCT.

    PubMed

    Rahmani, Faezeh; Seifi, Samaneh; Anbaran, Hossein Tavakoli; Ghasemi, Farshad

    2015-12-01

    An electron accelerator, ILU-14, with current of 10 mA and 100 kW in power has been considered as one of the options for neutron source in Boron Neutron Capture Therapy (BNCT). The final design of neutron target has been obtained using MCNPX to optimize the neutron production. Tungsten in strip shape and D2O in cylindrical form have been proposed as the photon converter and the photoneutron target, respectively. In addition calculation of heat deposition in the photon target design has been considered to ensure mechanical stability of target. The results show that about 8.37×10(12) photoneutron/s with average energy of 615 keV can be produced by this neutron source design. In addition, using an appropriate beam shaping assembly an epithermal neutron flux of the order of 1.24×10(8) cm(-2) s(-1) can be obtained for BNCT applications.

  3. Design of photon converter and photoneutron target for High power electron accelerator based BNCT.

    PubMed

    Rahmani, Faezeh; Seifi, Samaneh; Anbaran, Hossein Tavakoli; Ghasemi, Farshad

    2015-12-01

    An electron accelerator, ILU-14, with current of 10 mA and 100 kW in power has been considered as one of the options for neutron source in Boron Neutron Capture Therapy (BNCT). The final design of neutron target has been obtained using MCNPX to optimize the neutron production. Tungsten in strip shape and D2O in cylindrical form have been proposed as the photon converter and the photoneutron target, respectively. In addition calculation of heat deposition in the photon target design has been considered to ensure mechanical stability of target. The results show that about 8.37×10(12) photoneutron/s with average energy of 615 keV can be produced by this neutron source design. In addition, using an appropriate beam shaping assembly an epithermal neutron flux of the order of 1.24×10(8) cm(-2) s(-1) can be obtained for BNCT applications. PMID:26278347

  4. Tropical Atlantic climate simulated in the GFDL CM2.5 high-resolution coupled climate model

    NASA Astrophysics Data System (ADS)

    Doi, T.; Vecchi, G. A.; Rosati, A. J.; Delworth, T. L.

    2012-12-01

    Using two fully coupled ocean-atmosphere models of CM2.1 (the Climate Model version 2.1 developed at the Geophysical Fluid Dynamics Laboratory) and CM2.5 (a new high-resolution climate model based on CM2.1), the characteristics and sources of SST and precipitation biases associated with the Atlantic ITCZ have been investigated. CM2.5 has an improved simulation of the annual mean and the annual cycle of the rainfall over the Sahel and the northern South America, while CM2.1 shows excessive Sahel rainfall and lack of northern South America rainfall in boreal summer. This marked improvement in CM2.5 is due to not only high-resolved orography, but also a significant reduction of biases in the seasonal meridional migration of the ITCZ. In particular, the seasonal northward migration of the ITCZ in boreal summer is coupled to the seasonal variation of the SST and a subsurface doming of the thermocline in the northeastern tropical Atlantic, known as the Guinea Dome. Improvements in the ITCZ allow for better representation of the coupled processes that are important for an abrupt seasonally phase-locked decay of the interannual SST anomaly in the northern tropical Atlantic. Nevertheless, the differences between CM2.5 and CM2.1 were not sufficient to reduce the warm SST biases in the eastern equatorial region and Angola-Benguela Area. The weak bias of southerly winds along the southwestern African coast associated with the excessive southward migration bias of the ITCZ may be a key to improve the warm SST biases there. Also, response of climate conditions in the Atlantic Hurricane Main Development Region (MDR) to doubling of atmospheric CO2 with CM2.5 has been explored. In the annual mean, the SST in the MDR warms by about 2°C in the CO2 doubling run relative to the Control run, the trade winds become weaker in the northern tropical Atlantic, and the rainfall increases over the ITCZ and its northern region. The amplitude of the annual cycle of the SST over the MDR is not

  5. 19 CFR 10.8a - Imported articles exported and reimported.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Imported articles exported and reimported. 10.8a...; DEPARTMENT OF THE TREASURY ARTICLES CONDITIONALLY FREE, SUBJECT TO A REDUCED RATE, ETC. General Provisions Articles Exported and Returned § 10.8a Imported articles exported and reimported. (a) In addition...

  6. 19 CFR 10.8a - Imported articles exported and reimported.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 19 Customs Duties 1 2012-04-01 2012-04-01 false Imported articles exported and reimported. 10.8a...; DEPARTMENT OF THE TREASURY ARTICLES CONDITIONALLY FREE, SUBJECT TO A REDUCED RATE, ETC. General Provisions Articles Exported and Returned § 10.8a Imported articles exported and reimported. (a) In addition...

  7. 19 CFR 10.8a - Imported articles exported and reimported.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 19 Customs Duties 1 2011-04-01 2011-04-01 false Imported articles exported and reimported. 10.8a...; DEPARTMENT OF THE TREASURY ARTICLES CONDITIONALLY FREE, SUBJECT TO A REDUCED RATE, ETC. General Provisions Articles Exported and Returned § 10.8a Imported articles exported and reimported. (a) In addition...

  8. 19 CFR 10.8a - Imported articles exported and reimported.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 19 Customs Duties 1 2014-04-01 2014-04-01 false Imported articles exported and reimported. 10.8a...; DEPARTMENT OF THE TREASURY ARTICLES CONDITIONALLY FREE, SUBJECT TO A REDUCED RATE, ETC. General Provisions Articles Exported and Returned § 10.8a Imported articles exported and reimported. (a) In addition...

  9. 44 CFR 10.8 - Determination of requirement for environmental review.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 44 Emergency Management and Assistance 1 2010-10-01 2010-10-01 false Determination of requirement for environmental review. 10.8 Section 10.8 Emergency Management and Assistance FEDERAL EMERGENCY MANAGEMENT AGENCY, DEPARTMENT OF HOMELAND SECURITY GENERAL ENVIRONMENTAL CONSIDERATIONS Agency...

  10. A 50 EW/cm;2 Ti:sapphire laser system for studying relativistic light-matter interactions.

    PubMed

    Walker, B; Toth, C; Fittinghoff, D; Guo, T; Kim, D E; Rose-Petruck, C; Squier, J; Yamakawa, K; Wilson, K; Barty, C

    1999-11-01

    A 10-Hz repetition rate, 60-TW peak power, Ti:sapphire laser system was developed for use in experiments where relativistic effects dominate the physics. The temporal, spectral, energy and spatial characteristics of the laser pulses were measured in single shot format. The pulse duration ranged from 22 fs to 25 fs and the pulse energy averaged 1.3 J. Atomic photoionization measurements quantified the peak intensity of the laser pulse in situ. The measurements indicated an intensity of at least 510 19 W/cm 2 was produced.

  11. Coulomb-Boltzmann-Shifted distribution in laser-generated plasmas from 1010 up to 1019 W/cm2 intensities

    NASA Astrophysics Data System (ADS)

    Torrisi, L.

    2016-02-01

    The charge production from laser-generated plasmas generates not isotropically ion acceleration in vacuum and with mean kinetic energy proportional to the ion charge state. The ion velocity depends on many factors of which the most important are the plasma temperature, the adiabatic gas expansion in vacuum and the Coulomb acceleration. The ion energy distributions of the emitted ions from the plasma can be well explained by the Coulomb-Boltzmann-Shifted function, with a cut-off limitation at high energy for a wide range of laser intensities. It can be applied for intensities of 1010 W/cm2, when plasma is produced only in the backward direction from thick targets (backward plasma acceleration regime), as well as at intensities of the order of 1019 W/cm2, when plasma is produced in the forward direction from thin targets in target-normal sheath acceleration regime. It loses of validity in radiation pressure acceleration regime, at which ions are emitted near mono-energetically.

  12. Backward-going MeV electrons and gamma rays from 1018 W/cm2 laser interactions with water

    NASA Astrophysics Data System (ADS)

    Feister, Scott; Morrison, John T.; Frische, Kyle D.; Orban, Chris; Ovchinnikov, Vladimir M.; Nees, John A.; Austin, Drake R.; Chowdhury, Enam A.; Freeman, Richard R.; Roquemore, W. Melvyn

    2015-05-01

    Gamma rays with ~1 MeV energy are measured following the relativistic interaction of a 3 mJ, 1018 W/cm2 short pulse laser with a 30 μm diameter flowing water column. Contrary to expectations, radiation emission is peaked in the direction opposite to the normally-incident laser propagation (specular direction). Experimental measurements and particle-in-cell (PIC) simulations of laser-plasma interaction show a pre-formed-plasma-dependent, backward-going, beam-like primary electron source. The MeV component of the electron and gamma ray spectrum, which is more than five times the ponderomotive energy scale of the laser, is highly sensitive to the presence of a nanosecond-timescale laser pre-pulse. This research was sponsored by the Quantum and Non-Equilibrium Processes Division of the Air Force Office of Scientific Research, under the management of Dr. Enrique Parra, Program Manager.

  13. Spin-Hall-Effect-Assisted Electroresistance in Antiferromagnets via 105 A/cm2 dc Current

    NASA Astrophysics Data System (ADS)

    Han, Jiahao; Wang, Yuyan; Pan, Feng; Song, Cheng

    2016-08-01

    Antiferromagnet (AFM) spintronics with reduced electrical current is greatly expected to process information with high integration and low power consumption. In Pt/FeMn and Ta/FeMn hybrids, we observe significant resistance variation (up to 7% of the total resistance) manipulated by 105 A/cm2 dc current. We have excluded the contribution of isotropic structural effects, and confirmed the critical role of the spin Hall injection from Pt (or Ta) to FeMn. This electrical current-manipulated resistance (i.e. electroresistance) is proposed to be attributed to the spin-Hall-effect-induced spin-orbit torque in FeMn. Similar results have also been detected in plain IrMn films, where the charge current generates spin current via the spin Hall effect with the existence of Ir atoms. All the measurements are free from external magnetic fields and ferromagnets. Our findings present an interesting step towards high-efficiency spintronic devices.

  14. Xenoliths in the CM2 Carbonaceous Chondrite LON 94101: Implications for Complex Mixing on the Asteroidal Parent Body

    NASA Technical Reports Server (NTRS)

    Lindgren, P.; Lee, M. R.; Sofe, M.; Zolensky, M. E.

    2011-01-01

    Xenoliths are foreign clasts that oc-cur in various classes of meteorites, e.g. [1,2,3]. A re-cent study reveals the presence of several distinct classes of xenoliths in regolith-bearing meteorites, in-cluding in over 20 different carbonaceous chondrites [4]. The most common types of xenoliths are fine-grained hydrous clasts, often referred to as C1 or CI clasts in the literature, although their mineralogy is actually more similar to hydrous micrometeorites [5,6]. Xenoliths in meteorites present an opportunity to study material not yet classified or available as separate meteorites, and can provide additional information on processes in the dynamic early history of the Solar Sys-tem. Here we have performed chemical and mineralogi-cal analyses of xenoliths in the CM2 carbonaceous chondrite LON 94101, using scanning electron micro-scopy (SEM) and transmission electron microscopy (TEM).

  15. High e+/e- Ratio Dense Pair Creation with 1021W.cm-2 Laser Irradiating Solid Targets

    NASA Astrophysics Data System (ADS)

    Liang, E.; Clarke, T.; Henderson, A.; Fu, W.; Lo, W.; Taylor, D.; Chaguine, P.; Zhou, S.; Hua, Y.; Cen, X.; Wang, X.; Kao, J.; Hasson, H.; Dyer, G.; Serratto, K.; Riley, N.; Donovan, M.; Ditmire, T.

    2015-09-01

    We report results of new pair creation experiments using ~100 Joule pulses of the Texas Petawatt Laser to irradiate solid gold and platinum targets, with intensities up to ~1.9 × 1021 W.cm-2 and pulse durations as short as ~130 fs. Positron to electron (e+/e-) ratios >15% were observed for many thick disk and rod targets, with the highest e+/e- ratio reaching ~50% for a Pt rod. The inferred pair yield was ~ few ×1010 with emerging pair density reaching ~1015/cm3 so that the pair skin depth becomes < pair jet transverse size. These results represent major milestones towards the goal of creating a significant quantity of dense pair-dominated plasmas with e+/e- approaching 100% and pair skin depth ≪ pair plasma size, which will have wide-ranging applications to astrophysics and fundamental physics.

  16. Analysis of the biases in the downward shortwave surface flux in the GFDL CM2.1 general circulation model

    NASA Astrophysics Data System (ADS)

    Freidenreich, Stuart M.; Ramaswamy, V.

    2011-04-01

    Simulations of downward shortwave surface fluxes by the coupled Geophysical Fluid Dynamics Laboratory (GFDL) CM2.1 general circulation model are compared against climatology derived from the Baseline Surface Radiation Network (BSRN), Global Energy Balance Archive, and International Satellite Cloud Climatology Project ISCCP-FD data sets. The spatial pattern of the model's biases is evaluated. An investigation is made of how these relate to accompanying biases in total cloud amount and aerosol optical depth and how they affect the surface temperature simulation. Comparing CM2.1's clear-sky fluxes against BSRN site values, for European, Asian, and North American locations, there are underestimates in the direct and overestimates in the diffuse, resulting in underestimates in the total flux. These are related to overestimates of sulfate aerosol optical depth, arising owing to the behavior of the parameterization function for hygroscopic growth of these aerosols at very high relative humidity. Contrastingly, flux overestimate biases at lower latitude locations are associated with underestimates in sea-salt and carbonaceous aerosol amounts. All-sky flux biases consist of underestimates for North America, Eurasia, southern Africa, and northern oceanic regions and overestimates for the Amazon region, equatorial Africa, off the west coast of the Americas, and southern oceanic regions. These biases show strong correlations with cloud amount biases. There are modest correlations of the flux biases with cool surface temperature biases over North America and Eurasia, warm biases over the Amazon region, and cool (warm) biases over the northern (southern) oceanic regions. Analyses assuming nonhygroscopicity illustrate that there is a reduction of surface temperature biases accompanying a reduction of sulfate aerosol optical depth biases, whereas a more significant improvement in the temperature simulation requires refining the model's simulation of cloudiness.

  17. Gas-Phase Oxidation of Cm+ and Cm2+ -- Thermodynamics of neutral and ionized CmO

    SciTech Connect

    Gibson, John K; Haire, Richard G.; Santos, Marta; Pires de Matos, Antonio; Marcalo, Joaquim

    2008-12-08

    Fourier transform ion cyclotron resonance mass spectrometry was employed to study the products and kinetics of gas-phase reactions of Cm+ and Cm2+; parallel studies were carried out with La+/2+, Gd+/2+ and Lu+/2+. Reactions with oxygen-donor molecules provided estimates for the bond dissociation energies, D[M+-O](M = Cm, Gd, Lu). The first ionization energy, IE[CmO], was obtained from the reactivity of CmO+ with dienes, and the second ionization energies, IE[MO+](M = Cm, La, Gd, Lu), from the rates of electron-transfer reactions from neutrals to the MO2+ ions. The following thermodynamic quantities for curium oxide molecules were obtained: IE[CmO]= 6.4+-0.2 eV; IE[CmO+]= 15.8+-0.4 eV; D[Cm-O]= 710+-45 kJ mol-1; D[Cm+-O]= 670+-40 kJ mol-1; and D[Cm2+-O]= 342+-55 kJ mol-1. Estimates for the M2+-O bond energies for M = Cm, La, Gd and Lu are all intermediate between D[N2-O]and D[OC-O]--i.e., 167 kJ mol-1< D[M2+-O]< 532 kJ mol-1 -- such that the four MO2+ ions fulfill the thermodynamic requirement for catalytic O-atom transport from N2O to CO. It was demonstrated that the kinetics are also favorable and that the CmO2+, LaO2+, GdO2+ and LuO2+ dipositive ions each catalyze the gas-phase oxidation of CO to CO2 by N2O. The CmO2+ ion appeared during the reaction of Cm+ with O2 when the intermediate, CmO+, was not collisionally cooled -- although its formation is kinetically and/or thermodynamically unfavorable, CmO2+ is a stable species.

  18. Spin-Hall-Effect-Assisted Electroresistance in Antiferromagnets via 10(5) A/cm(2) dc Current.

    PubMed

    Han, Jiahao; Wang, Yuyan; Pan, Feng; Song, Cheng

    2016-01-01

    Antiferromagnet (AFM) spintronics with reduced electrical current is greatly expected to process information with high integration and low power consumption. In Pt/FeMn and Ta/FeMn hybrids, we observe significant resistance variation (up to 7% of the total resistance) manipulated by 10(5) A/cm(2) dc current. We have excluded the contribution of isotropic structural effects, and confirmed the critical role of the spin Hall injection from Pt (or Ta) to FeMn. This electrical current-manipulated resistance (i.e. electroresistance) is proposed to be attributed to the spin-Hall-effect-induced spin-orbit torque in FeMn. Similar results have also been detected in plain IrMn films, where the charge current generates spin current via the spin Hall effect with the existence of Ir atoms. All the measurements are free from external magnetic fields and ferromagnets. Our findings present an interesting step towards high-efficiency spintronic devices. PMID:27546199

  19. Clasts in the CM2 carbonaceous chondrite Lonewolf Nunataks 94101: Evidence for aqueous alteration prior to complex mixing

    NASA Astrophysics Data System (ADS)

    Lindgren, Paula; Lee, Martin R.; Sofe, Mahmood R.; Zolensky, Michael E.

    2013-06-01

    Clasts in the CM2 carbonaceous chondrite Lonewolf Nunataks (LON) 94101 have been characterized using scanning and transmission electron microscopy and electron microprobe analysis to determine their degrees of aqueous alteration, and the timing of alteration relative to incorporation of clasts into the host. The provenance of the clasts, and the mechanism by which they were incorporated and mixed with their host material are also considered. Results show that at least five distinct types of clasts occur in LON 94101, of which four have been aqueously altered to various degrees and one is largely anhydrous. The fact that they have had different alteration histories implies that the main part of aqueous activity occurred prior to the mixing and assimilation of the clasts with their host. Further, the presence of such a variety of clasts suggests complex mixing in a dynamic environment involving material from various sources. Two of the clasts, one containing approximately 46 vol% carbonate and the other featuring crystals of pyrrhotite up to approximately 1 mm in size, are examples of unusual lithologies and indicate concentration of chemical elements in discrete areas of the parent body(ies), possibly by flow of aqueous solutions.

  20. Spin-Hall-Effect-Assisted Electroresistance in Antiferromagnets via 105 A/cm2 dc Current

    PubMed Central

    Han, Jiahao; Wang, Yuyan; Pan, Feng; Song, Cheng

    2016-01-01

    Antiferromagnet (AFM) spintronics with reduced electrical current is greatly expected to process information with high integration and low power consumption. In Pt/FeMn and Ta/FeMn hybrids, we observe significant resistance variation (up to 7% of the total resistance) manipulated by 105 A/cm2 dc current. We have excluded the contribution of isotropic structural effects, and confirmed the critical role of the spin Hall injection from Pt (or Ta) to FeMn. This electrical current-manipulated resistance (i.e. electroresistance) is proposed to be attributed to the spin-Hall-effect-induced spin-orbit torque in FeMn. Similar results have also been detected in plain IrMn films, where the charge current generates spin current via the spin Hall effect with the existence of Ir atoms. All the measurements are free from external magnetic fields and ferromagnets. Our findings present an interesting step towards high-efficiency spintronic devices. PMID:27546199

  1. Muscovy duck reovirus p10.8 protein localizes to the nucleus via a nonconventional nuclear localization signal

    PubMed Central

    2014-01-01

    Background It was previously report that the first open reading frame of Muscovy duck reocvirus S4 gene encodes a 95-amino-acid protein, designed p10.8, which has no sequence similarity to other known proteins. Its amino acid sequence offers no clues about its function. Results Subcellular localization and nuclear import signal of p10.8 were characterized. We found that p10.8 protein localizes to the nucleus of infected and transfected cells, suggesting that p10.8 nuclear localization is not facilitated by viral infection or any other viral protein. A functional non-canonical nuclear localization signal (NLS) for p10.8 was identified and mapped to N-terminus residues 1–40. The NLS has the ability to retarget a large cytoplasmic protein to the nucleus. Conclusions p10.8 imported into the nucleus might via a nonconventional signal nuclear signal. PMID:24564937

  2. Photon-photon collisions

    SciTech Connect

    Burke, D.L.

    1982-10-01

    Studies of photon-photon collisions are reviewed with particular emphasis on new results reported to this conference. These include results on light meson spectroscopy and deep inelastic e..gamma.. scattering. Considerable work has now been accumulated on resonance production by ..gamma gamma.. collisions. Preliminary high statistics studies of the photon structure function F/sub 2//sup ..gamma../(x,Q/sup 2/) are given and comments are made on the problems that remain to be solved.

  3. Photon-photon colliders

    SciTech Connect

    Sessler, A.M.

    1995-04-01

    Since the seminal work by Ginsburg, et at., the subject of giving the Next Linear Collider photon-photon capability, as well as electron-positron capability, has drawn much attention. A 1990 article by V.I. Teinov describes the situation at that time. In March 1994, the first workshop on this subject was held. This report briefly reviews the physics that can be achieved through the photon-photon channel and then focuses on the means of achieving such a collider. Also reviewed is the spectrum of backscattered Compton photons -- the best way of obtaining photons. We emphasize the spectrum actually obtained in a collider with both polarized electrons and photons (peaked at high energy and very different from a Compton spectrum). Luminosity is estimated for the presently considered colliders, and interaction and conversion-point geometries are described. Also specified are laser requirements (such as wavelength, peak power, and average power) and the lasers that might be employed. These include conventional and free-electron lasers. Finally, we describe the R&D necessary to make either of these approaches viable and explore the use of the SLC as a test bed for a photon-photon collider of very high energy.

  4. Photon-photon colliders

    SciTech Connect

    Sessler, Andrew M.

    1996-01-01

    Since the seminal work by Ginsburg, et al., the subject of giving the Next Linear Collider photon-photon capability, as well as electron-positron capability, has drawn much attention [1]. A 1990 article by V.I. Telnov describes the situation at that time [2]. In March 1994, the first workshop on this subject was held [3]. This report briefly reviews the physics that can be achieved through the photon-photon channel and then focuses on the means of achieving such a collider. Also reviewed is the spectrum of backscattered Compton photons—the best way of obtaining photons. We emphasize the spectrum actually obtained in a collider with both polarized electrons and photons (peaked at high energy and very different from a Compton spectrum). Luminosity is estimated for the presently considered colliders, and interaction and conversion-point geometries are described. Also specified are laser requirements (such as wavelength, peak power, and average power) and the lasers that might be employed. These include conventional and free-electron lasers. Finally, we describe the R&D necessary to make either of these approaches viable and explore the use of the SLC as a test bed for a photon-photon collider of very high energy.

  5. Photon-photon collisions

    SciTech Connect

    Brodsky, S.J.

    1988-07-01

    Highlights of the VIIIth International Workshop on Photon-Photon Collisions are reviewed. New experimental and theoretical results were reported in virtually every area of ..gamma gamma.. physics, particularly in exotic resonance production and tests of quantum chromodynamics where asymptotic freedom and factorization theorems provide predictions for both inclusive and exclusive ..gamma gamma.. reactions at high momentum transfer. 73 refs., 12 figs.

  6. Perovskite CH3NH3PbI3(Cl) Single Crystals: Rapid Solution Growth, Unparalleled Crystalline Quality, and Low Trap Density toward 10(8) cm(-3).

    PubMed

    Lian, Zhipeng; Yan, Qingfeng; Gao, Taotao; Ding, Jie; Lv, Qianrui; Ning, Chuangang; Li, Qiang; Sun, Jia-Lin

    2016-08-01

    Single crystal reflects the intrinsic physical properties of a material, and single crystals with high-crystalline quality are highly desired for the acquisition of high-performance devices. We found that large single crystals of perovskite CH3NH3PbI3(Cl) could be grown rapidly from chlorine-containing solutions. Within 5 days, CH3NH3PbI3(Cl) single crystal as large as 20 mm × 18 mm × 6 mm was harvested. As a most important index to evaluate the crystalline quality, the full width at half-maximum (fwhm) in the high-resolution X-ray rocking curve (HR-XRC) of as-grown CH3NH3PbI3(Cl) single crystal was measured as 20 arcsec, which is far superior to so far reported CH3NH3PbI3 single crystals (∼1338 arcsec). The unparalleled crystalline quality delivered a low trap-state density of down to 7.6 × 10(8) cm(-3), high carrier mobility of 167 ± 35 cm(2) V(-1) s(-1), and long transient photovoltaic carrier lifetime of 449 ± 76 μs. The improvement in the crystalline quality, together with the rapid growth rate and excellent carrier transport property, provides state-of-the-art single crystalline hybrid perovskite materials for high-performance optoelectronic devices. PMID:27458057

  7. Photon-photon collisions

    SciTech Connect

    Brodsky, S.J.

    1985-01-01

    The study of photon-photon collisions has progressed enormously, stimulated by new data and new calculational tools for QCD. In the future we can expect precise determinations of ..cap alpha../sub s/ and ..lambda../sup ms/ from the ..gamma..*..gamma.. ..-->.. ..pi../sup 0/ form factor and the photon structure function, as well as detailed checks of QCD, determination of the shape of the hadron distribution amplitudes from ..gamma gamma.. ..-->.. H anti H, reconstruction of sigma/sub ..gamma gamma../ from exclusive channels at low W/sub ..gamma gamma../, definitive studies of high p/sub T/ hadron and jet production, and studies of threshold production of charmed systems. Photon-photon collisions, along with radiative decays of the psi and UPSILON, are ideal for the study of multiquark and gluonic resonances. We have emphasized the potential for resonance formation near threshold in virtually every hadronic exclusive channel, including heavy quark states c anti c c anti c, c anti c u anti u, etc. At higher energies SLC, LEP, ...) parity-violating electroweak effects and Higgs production due to equivalent Z/sup 0/ and W/sup + -/ beams from e ..-->.. eZ/sup 0/ and e ..-->.. nu W will become important. 44 references.

  8. Epitaxial growth of large area single-crystalline few-layer MoS2 with high space charge mobility of 192 cm2 V-1 s-1

    NASA Astrophysics Data System (ADS)

    Ma, Lu; Nath, Digbijoy N.; Lee, Edwin W.; Lee, Choong Hee; Yu, Mingzhe; Arehart, Aaron; Rajan, Siddharth; Wu, Yiying

    2014-08-01

    We report on the vapor-solid growth of single crystalline few-layer MoS2 films on (0001)-oriented sapphire with excellent structural and electrical properties over centimeter length scale. High-resolution X-ray diffraction scans indicated that the films had good out-of-plane ordering and epitaxial registry. A carrier density of ˜2 × 1011 cm-2 and a room temperature mobility of 192 cm2/Vs were extracted from space-charge limited transport regime in the films. The electron mobility was found to exhibit in-plane anisotropy with a ratio of ˜1.8. Theoretical estimates of the temperature-dependent electron mobility including optical phonon, acoustic deformation potential, and remote ionized impurity scattering were found to satisfactorily match the measured data. The synthesis approach reported here demonstrates the feasibility of device quality few-layer MoS2 films with excellent uniformity and high quality.

  9. Is H2O present on Io? The detection of a new strong band near 3590/cm (2.79 microns)

    NASA Astrophysics Data System (ADS)

    Salama, F.; Allamandola, L. J.; Sandford, S. A.; Bregman, J. D.; Witteborn, F. C.; Cruikshank, D. P.

    1994-02-01

    A strong absorption band at 3590 +/- 20/cm (2.790 +/- 0.015 microns) has been discovered in the spectrum of Io using the Kuiper Airborne Observatory (KAO). The 2nu1 + nu3 combination mode of solid SO2 falls at this position. Since SO2 is abundant on Io it must contribute to the new band. However, a band due to H2O was predicted near this frequency in Io's spectrum based on laboratory experiments of H2O:SO2 mixed Io ice analogs which were used to assign the two weak, variable features at 3370 and 3170/cm (2.97 and 3.15 microns) to trace amounts of H2O frozen in solid SO2 on Io. The new band probably originates from both SO2 and H2O. Unfortunately, the spectral resolution of the data is insufficient to settle the issue of whether there are two resolvable components.

  10. Schottky barrier diodes of corundum-structured gallium oxide showing on-resistance of 0.1 mΩ·cm2 grown by MIST EPITAXY®

    NASA Astrophysics Data System (ADS)

    Oda, Masaya; Tokuda, Rie; Kambara, Hitoshi; Tanikawa, Tomochika; Sasaki, Takahiro; Hitora, Toshimi

    2016-02-01

    Thin-film corundum-structured gallium oxide (α-Ga2O3) Schottky barrier diodes (SBDs) were fabricated by growing α-Ga2O3 layers on sapphire substrates by the safe, low-cost, and energy-saving MIST EPITAXY® technique, followed by lifting off the α-Ga2O3 layers from the substrates. The SBDs exhibited on-resistance and breakdown voltage of 0.1 mΩ·cm2 and 531 V (SBD1) or 0.4 mΩ·cm2 and 855 V (SBD2), respectively. These results will encourage the future evolution of low-cost and high-performance SBDs with α-Ga2O3.

  11. A Cofacially Stacked Electron-Deficient Small Molecule with a High Electron Mobility of over 10 cm(2) V(-1) s(-1) in Air.

    PubMed

    Dou, Jin-Hu; Zheng, Yu-Qing; Yao, Ze-Fan; Lei, Ting; Shen, Xingxing; Luo, Xu-Yi; Yu, Zhi-Ao; Zhang, Shi-Ding; Han, Guangchao; Wang, Zhi; Yi, Yuanping; Wang, Jie-Yu; Pei, Jian

    2015-12-22

    A strong, electron-deficient small molecule, F4 -BDOPV, has a lowest unoccupied molecular orbital (LUMO) level down to -4.44 eV and exhibits cofacial packing in single crystals. These features provide F4 -BDOPV with good ambient stability and large charge-transfer integrals for electrons, leading to a high electron mobility of up to 12.6 cm(2) V(-1) s(-1) in air.

  12. Dynamics of cell and tissue growth acquired by means of 25 mm2 to 10 cm2 lens-free imaging

    NASA Astrophysics Data System (ADS)

    Momey, F.; Coutard, J.-G.; Bordy, T.; Navarro, F.; Menneteau, M.; Dinten, J.-M.; Allier, C.

    2015-03-01

    In this paper, we discuss a new methodology based on lens-free imaging to perform wound healing assay with unprecedented statistics. Our video lens-free microscopy setup is a simple optical system featuring only a CMOS sensor and a semi coherent illumination system. Yet it is a powerful means for the real-time monitoring of cultivated cells. It presents several key advantages, e.g., integration into standard incubator, compatibility with standard cell culture protocol, simplicity and ease of use. It can perform the follow-up in a large field of view (25 mm2) of several crucial parameters during the culture of cells i.e. their motility, their proliferation rate or their death. Consequently the setup can gather large statistics both in space and time. But in the case of tissue growth experiments, the field of view of 25 mm2 remains not sufficient and results can be biased depending on the position of the device with respect to the recipient of the cell culture. Hence, to conduct exhaustive wound healing assay, here we propose to enlarge the field of view up to 10 cm2 through two different approaches. The first method consists in performing a scan of the cell culture by moving the source/sensor couple and then stitch the stack of images. The second is to make an acquisition by scanning with a line scan camera. The two approaches are compared in term of resolution, complexity and acquisition time. Next we have performed acquisitions of wound healing assay (keratinocytes HaCaT) both in real-time (25 mm2) and in final point (10 cm2) to assess the combination of these two complementary modalities. In the future, we aim at combining directly super wide field of view acquisitions (>10 cm2) with real time ability inside the incubator.

  13. MgZnO/ZnO heterostructures with electron mobility exceeding 1 × 10(6) cm(2)/Vs.

    PubMed

    Falson, Joseph; Kozuka, Yusuke; Uchida, Masaki; Smet, Jurgen H; Arima, Taka-Hisa; Tsukazaki, Atsushi; Kawasaki, Masashi

    2016-01-01

    The inherently complex chemical and crystallographic nature of oxide materials has suppressed the purities achievable in laboratory environments, obscuring the rich physical degrees of freedom these systems host. In this manuscript we provide a systematic approach to defect identification and management in oxide molecular beam epitaxy grown MgZnO/ZnO heterostructures which host two-dimensional electron systems. We achieve samples displaying electron mobilities in excess of 1 × 10(6) cm(2)/Vs. This data set for the MgZnO/ZnO system firmly establishes that the crystalline quality has become comparable to traditional semiconductor materials. PMID:27229479

  14. MgZnO/ZnO heterostructures with electron mobility exceeding 1 × 106 cm2/Vs

    PubMed Central

    Falson, Joseph; Kozuka, Yusuke; Uchida, Masaki; Smet, Jurgen H.; Arima, Taka-hisa; Tsukazaki, Atsushi; Kawasaki, Masashi

    2016-01-01

    The inherently complex chemical and crystallographic nature of oxide materials has suppressed the purities achievable in laboratory environments, obscuring the rich physical degrees of freedom these systems host. In this manuscript we provide a systematic approach to defect identification and management in oxide molecular beam epitaxy grown MgZnO/ZnO heterostructures which host two-dimensional electron systems. We achieve samples displaying electron mobilities in excess of 1 × 106 cm2/Vs. This data set for the MgZnO/ZnO system firmly establishes that the crystalline quality has become comparable to traditional semiconductor materials. PMID:27229479

  15. MgZnO/ZnO heterostructures with electron mobility exceeding 1 × 106 cm2/Vs

    NASA Astrophysics Data System (ADS)

    Falson, Joseph; Kozuka, Yusuke; Uchida, Masaki; Smet, Jurgen H.; Arima, Taka-Hisa; Tsukazaki, Atsushi; Kawasaki, Masashi

    2016-05-01

    The inherently complex chemical and crystallographic nature of oxide materials has suppressed the purities achievable in laboratory environments, obscuring the rich physical degrees of freedom these systems host. In this manuscript we provide a systematic approach to defect identification and management in oxide molecular beam epitaxy grown MgZnO/ZnO heterostructures which host two-dimensional electron systems. We achieve samples displaying electron mobilities in excess of 1 × 106 cm2/Vs. This data set for the MgZnO/ZnO system firmly establishes that the crystalline quality has become comparable to traditional semiconductor materials.

  16. High-voltage thin-film GaN LEDs fabricated on ceramic substrates: the alleviated droop effect at 670 W/cm(2).

    PubMed

    Tsai, M L; Liao, J H; Yeh, J H; Hsu, T C; Hon, S J; Chung, T Y; Lai, K Y

    2013-11-01

    High-voltage thin-film GaN LEDs with the emission wavelength of 455 nm were fabricated on ceramic substrates (230 W/m · K). The high-voltage operation was achieved by three cascaded sub-LEDs with dielectric passivation and metal bridges conformally deposited on the side walls. Under the driving power of 670 W/cm(2), the high-voltage LEDs exhibit much alleviated efficiency droop and the operative temperature below 80 °C. The excellent performances were attributed to the improved current spreading within each sub-LED and the superior heat sinking of the ceramic substrate.

  17. Widely bandgap tunable amorphous Cd-Ga-O oxide semiconductors exhibiting electron mobilities ≥10 cm2 V-1 s-1

    NASA Astrophysics Data System (ADS)

    Yanagi, Hiroshi; Sato, Chiyuki; Kimura, Yota; Suzuki, Issei; Omata, Takahisa; Kamiya, Toshio; Hosono, Hideo

    2015-02-01

    Amorphous oxide semiconductors exhibit large electron mobilities; however, their bandgaps are either too large for solar cells or too small for deep ultraviolet applications depending on the materials system. Herein, we demonstrate that amorphous Cd-Ga-O semiconductors display bandgaps covering the entire 2.5-4.3 eV region while maintaining large electron mobilities ≥10 cm2 V-1 s-1. The band alignment diagram obtained by ultraviolet photoemission spectroscopy and the bandgap values reveal that these semiconductors form type-II heterojunctions with p-type Cu2O, which is suitable for solar cells and solar-blind ultraviolet sensors.

  18. Reflectance Spectra of CM2 Chondrite Mighei Irradiated with Pulsed Laser and Implications for Low-Albedo Asteroids and Martian Moons

    NASA Technical Reports Server (NTRS)

    Moroz, L. V.; Hiroi, T.; Shingareva, T. V.; Basilevsky, A. T.; Fisenko, A. V.; Semjonova, L. F.; Pieters, C. M.

    2004-01-01

    Micrometeoritic bombardment is an important space weathering process modifying surface optical properties of airless solar system bodies. We have used irradiation with a microsecond pulsed laser as an experimental method to simulate such a process on various targets. The experiment discussed here was performed on a powdered sample of CM2 carbonaceous chondrite Mighei. Shingareva et al. report the details of experimental procedure as well as the results of mineralogical and chemical studies of the irradiated material. Here we present reflectance spectra of irradiated Mighei samples and discuss their spectral properties compared to those of non-irradiated meteorite and low-albedo small solar system bodies.

  19. AMINO ACID ANALYSES OF THE ANTARCTIC CM2 METEORITES ALH 83100 AND LEW 90500 USING LIQUID CHROMATOGRAPHY-TIME OF FLIGHT-MASS SPECTROMETRY

    NASA Technical Reports Server (NTRS)

    Glavin, D. P.; Dworkin, J. P.; Aubrey, A.; Botta, O.; Doty, J. H., III; Bada, J. L.

    2001-01-01

    The investigation of organic compounds in primitive carbonaceous meteorites provides a record of the chemical processes that occurred in the early solar system. In particular, amino acids have been shown to be potential indicators in tracing the nature of carbonaceous chondrite parent bodies [ 13. The delivery of amino acids by carbonaceous chondrites to the early Earth could have been any important source of the Earth's prebiotic organic inventory [2]. Over 80 different amino acids have been detected in the Murchison CM2 meteorite, most of them completely non-existent in the terrestrial biosphere [3]. We have optimized a new liquid chromatography-time-of-flight-mass spectrometry (LC-ToF-MS) technique coupled with OPAMAC derivatization in order to detect amino acids in meteorite extracts by UV fluorescence and exact mass simultaneously. The detection limit of the LC-ToF-MS instrument for amino acids is at least 3 orders of magnitude lower than traditional GC-MS techniques. Here we report on the first analyses of amino acids and their enantiomeric abundances in the CM2 carbonaceous meteorites ALH 83100, LEW 90500, and Murchison using this new LC-ToF-MS instrument configuration. Amino acid analyses of any kind for the CM meteorite ALH 83100 have not previously been reported.

  20. Tailoring gadolinium-doped ceria-based solid oxide fuel cells to achieve 2 W cm(-2) at 550 °C.

    PubMed

    Lee, Jin Goo; Park, Jeong Ho; Shul, Yong Gun

    2014-06-04

    Low-temperature operation is necessary for next-generation solid oxide fuel cells due to the wide variety of their applications. However, significant increases in the fuel cell losses appear in the low-temperature solid oxide fuel cells, which reduce the cell performance. To overcome this problem, here we report Gd0.1Ce0.9O1.95-based low-temperature solid oxide fuel cells with nanocomposite anode functional layers, thin electrolytes and core/shell fibre-structured Ba0.5Sr0.5Co0.8Fe0.2O3-δ-Gd0.1Ce0.9O1.95 cathodes. In particular, the report describes the use of the advanced electrospinning and Pechini process in the preparation of the core/shell-fibre-structured cathodes. The fuel cells show a very high performance of 2 W cm(-2) at 550 °C in hydrogen, and are stable for 300 h even under the high current density of 1 A cm(-2). Hence, the results suggest that stable and high-performance solid oxide fuel cells at low temperatures can be achieved by modifying the microstructures of solid oxide fuel cell components.

  1. Current density and catalyst-coated membrane resistance distribution of hydro-formed metallic bipolar plate fuel cell short stack with 250 cm2 active area

    NASA Astrophysics Data System (ADS)

    Haase, S.; Moser, M.; Hirschfeld, J. A.; Jozwiak, K.

    2016-01-01

    An automotive fuel cell with an active area of 250 cm2 is investigated in a 4-cell short stack with a current and temperature distribution device next to the bipolar plate with 560 current and 140 temperature segments. The electrical conductivities of the bipolar plate and gas diffusion layer assembly are determined ex-situ with this current scan shunt module. The applied fuel cell consists of bipolar plates constructed of 75-μm-thick, welded stainless-steel foils and a graphitic coating. The electrical conductivities of the bipolar plate and gas diffusion layer assembly are determined ex-situ with this module with a 6% deviation in in-plane conductivity. The current density distribution is evaluated up to 2.4 A cm-2. The entire cell's investigated volumetric power density is 4.7 kW l-1, and its gravimetric power density is 4.3 kW kg-1 at an average cell voltage of 0.5 V. The current density distribution is determined without influencing the operating cell. In addition, the current density distribution in the catalyst-coated membrane and its effective resistivity distribution with a finite volume discretisation of Ohm's law are evaluated. The deviation between the current density distributions in the catalyst-coated membrane and the bipolar plate is determined.

  2. The oxygen isotope evolution of parent body aqueous solutions as recorded by multiple carbonate generations in the Lonewolf Nunataks 94101 CM2 carbonaceous chondrite

    NASA Astrophysics Data System (ADS)

    Lee, M. R.; Sofe, M. R.; Lindgren, P.; Starkey, N. A.; Franchi, I. A.

    2013-11-01

    The CM2 carbonaceous chondrite LON 94101 contains aragonite and two generations of calcite that provide snapshots of the chemical and isotopic evolution of aqueous solutions during parent body alteration. Aragonite was the first carbonate to crystallize. It is rare, heterogeneously distributed within the meteorite matrix, and its mean oxygen isotope values are δ18O 39.9 ± 0.6‰, Δ17O -0.3 ± 1.0‰ (1σ). Calcite precipitated soon afterwards, and following a fall in solution Mg/Ca ratios, to produce small equant grains with a mean oxygen isotope value of δ18O 37.5 ± 0.7‰, Δ17O 1.4 ± 1.1‰ (1σ). These grains were partially or completely replaced by serpentine and tochilinite prior to precipitation of the second generation of calcite, which occluded an open fracture to form a millimetre-sized vein, and replaced anhydrous silicates within chondrules and the matrix. The vein calcite has a mean composition of δ18O 18.4 ± 0.3‰, Δ17O -0.5 ± 0.5‰ (1σ). Petrographic and isotopic results therefore reveal two discrete episodes of mineralisation that produced calcite generations with contrasting δ18O, and mean Δ17O values. The aragonite and equant calcite crystallized over a relatively brief period early in the aqueous alteration history of the parent body, and from static fluids that were evolving chemically in response to mineral dissolution and precipitation. The second calcite generation crystallized from solutions of a lower Δ17O, and a lower δ18O and/or higher temperature. As two generations of calcite whose petrographic characteristics and oxygen isotopic compositions are similar to those in LON 94101 occur in at least one other CM2, multiphase carbonate mineralisation could be the typical outcome of the sequence of chemical reactions during parent body aqueous alteration. It is equally possible however that the second generation of calcite formed in response to an event such as impact fracturing and concomitant fluid mobilisation that affected

  3. Perovskite photonic sources

    NASA Astrophysics Data System (ADS)

    Sutherland, Brandon R.; Sargent, Edward H.

    2016-05-01

    The field of solution-processed semiconductors has made great strides; however, it has yet to enable electrically driven lasers. To achieve this goal, improved materials are required that combine efficient (>50% quantum yield) radiative recombination under high injection, large and balanced charge-carrier mobilities in excess of 10 cm2 V-1 s-1, free-carrier densities greater than 1017 cm-3 and gain coefficients exceeding 104 cm-1. Solid-state perovskites are -- in addition to galvanizing the field of solar electricity -- showing great promise in photonic sources, and may be the answer to realizing solution-cast laser diodes. Here, we discuss the properties of perovskites that benefit light emission, review recent progress in perovskite electroluminescent diodes and optically pumped lasers, and examine the remaining challenges in achieving continuous-wave and electrically driven lasing.

  4. Three-dimensional nanostructured bilayer solid oxide fuel cell with 1.3 W/cm(2) at 450 °C.

    PubMed

    An, Jihwan; Kim, Young-Beom; Park, Joonsuk; Gür, Turgut M; Prinz, Fritz B

    2013-09-11

    Obtaining high power density at low operating temperatures has been an ongoing challenge in solid oxide fuel cells (SOFC), which are efficient engines to generate electrical energy from fuels. Here we report successful demonstration of a thin-film three-dimensional (3-D) SOFC architecture achieving a peak power density of 1.3 W/cm(2) obtained at 450 °C. This is made possible by nanostructuring of the ultrathin (60 nm) electrolyte interposed with a nanogranular catalytic interlayer at the cathode/electrolyte interface. We attribute the superior cell performance to significant reduction in both the ohmic and the polarization losses due to the combined effects of employing an ultrathin film electrolyte, enhancement of effective area by 3-D architecture, and superior catalytic activity by the ceria-based interlayer at the cathode. These insights will help design high-efficiency SOFCs that operate at low temperatures with power densities that are of practical significance.

  5. X-Ray Radiation Measurements With Photodiodes In Plasmas Generated By 1017 W/Cm2 Intensity Krf Excimer Laser Pulses

    NASA Astrophysics Data System (ADS)

    Rácz, E.; Földes, I. B.; Ryć, L.

    2006-01-01

    Experiments were carried out using a prepulse-free hybrid KrF excimer-dye laser system (700fs pulse duration, 248nm wavelength, 15mJ pulse energy). The intensity of the p-polarized, focused laser beam was 1.5ṡ1017 W/cm2. Vacuum ultraviolet (VUV) and x-rays from solid state laser plasmas were generated in the laser-plasma interaction of subpicosecond laser pulses of nonrelativistic laser intensities. An x-ray sensitive FLM photodiode (ITE, Warsaw) was used to detect x-rays between 1-19 keV in front of the targets. The diode was filtered by a 4μm Al foil. The dependence of the x-ray flux on laser intensity and the angular distribution of x-rays for aluminum and copper targets in the half space of the front side of the targets were investigated.

  6. Compositions of Partly Altered Olivine and Replacement Serpentine in the CM2 Chondrites QUE93005 and Nogoya: Implications for Scales of Elemental Redistribution During Aqueous Alteration

    NASA Technical Reports Server (NTRS)

    Velbel, M. A.; Tonui, E. K.; Zolensky, M. E.

    2003-01-01

    Some phyllosilicates in CM carbonaceous chondrites formed by aqueous alteration of anhydrous precursor phases. Although broad trends in the compositions of hydrous phyllosilicates are recognized and believed to be related to trends in degree of aqueous alteration, details of the reactions that formed specific secondary minerals remain obscure. This paper reports compositional relationships between remnants of partially pseudomorphically replaced silicates and their alteration products (serpentine) in the CM2 chondrites QUE93005 and Nogoya and compares both with previously published results for Allan Hills 81002. By focusing on serpentine formed from known reactants (olivines), and on only those instances in which some of the reactant silicate remains, direct compositional relationships between reactants and products, and the elemental mobility required by the reactions, can be established.

  7. Pushing the Photon Limit: Nanoantennas Increase Maximal Photon Stream and Total Photon Number.

    PubMed

    Wientjes, Emilie; Renger, Jan; Cogdell, Richard; van Hulst, Niek F

    2016-05-01

    Nanoantennas are well-known for their effective role in fluorescence enhancement, both in excitation and emission. Enhancements of 3-4 orders of magnitude have been reported. Yet in practice, the photon emission is limited by saturation due to the time that a molecule spends in singlet and especially triplet excited states. The maximal photon stream restricts the attainable enhancement. Furthermore, the total number of photons emitted is limited by photobleaching. The limited brightness and observation time are a drawback for applications, especially in biology. Here we challenge this photon limit, showing that nanoantennas can actually increase both saturation intensity and photostability. So far, this limit-shifting role of nanoantennas has hardly been explored. Specifically, we demonstrate that single light-harvesting complexes, under saturating excitation conditions, show over a 50-fold antenna-enhanced photon emission stream, with 10-fold more total photons, up to 10(8) detected photons, before photobleaching. This work shows yet another facet of the great potential of nanoantennas in the world of single-molecule biology.

  8. Test of Equivalence Principle at 10(-8) Level by a Dual-Species Double-Diffraction Raman Atom Interferometer.

    PubMed

    Zhou, Lin; Long, Shitong; Tang, Biao; Chen, Xi; Gao, Fen; Peng, Wencui; Duan, Weitao; Zhong, Jiaqi; Xiong, Zongyuan; Wang, Jin; Zhang, Yuanzhong; Zhan, Mingsheng

    2015-07-01

    We report an improved test of the weak equivalence principle by using a simultaneous 85Rb-87Rb dual-species atom interferometer. We propose and implement a four-wave double-diffraction Raman transition scheme for the interferometer, and demonstrate its ability in suppressing common-mode phase noise of Raman lasers after their frequencies and intensity ratios are optimized. The statistical uncertainty of the experimental data for Eötvös parameter η is 0.8×10(-8) at 3200 s. With various systematic errors corrected, the final value is η=(2.8±3.0)×10(-8). The major uncertainty is attributed to the Coriolis effect. PMID:26182096

  9. Test of Equivalence Principle at 10(-8) Level by a Dual-Species Double-Diffraction Raman Atom Interferometer.

    PubMed

    Zhou, Lin; Long, Shitong; Tang, Biao; Chen, Xi; Gao, Fen; Peng, Wencui; Duan, Weitao; Zhong, Jiaqi; Xiong, Zongyuan; Wang, Jin; Zhang, Yuanzhong; Zhan, Mingsheng

    2015-07-01

    We report an improved test of the weak equivalence principle by using a simultaneous 85Rb-87Rb dual-species atom interferometer. We propose and implement a four-wave double-diffraction Raman transition scheme for the interferometer, and demonstrate its ability in suppressing common-mode phase noise of Raman lasers after their frequencies and intensity ratios are optimized. The statistical uncertainty of the experimental data for Eötvös parameter η is 0.8×10(-8) at 3200 s. With various systematic errors corrected, the final value is η=(2.8±3.0)×10(-8). The major uncertainty is attributed to the Coriolis effect.

  10. Diode laser spectra of CCl2F2 near 10.8 muon M: Air-broadening effects

    NASA Technical Reports Server (NTRS)

    Jennings, D. E.

    1977-01-01

    Laboratory spectra of CCL2F2 in the 10.8 micron region was recorded, using a tuneable diode laser spectrometer. Effects of air-broadening at pressures up to 48 Torr show that spectral structure should be exhibited under high resolution at altitudes as low as 19 Km. The single line, pressure-broadening coefficient for CCL2F2 was estimated to be 8 MHz/Torr FWHM.

  11. Speculations on a relativistic strong focusing self-collider with very high luminosity (≥10 40 cm -2s -1): Macroproduction of antinuclei and other micro cross section events and formation of ambiplasma

    NASA Astrophysics Data System (ADS)

    Maglich, Bogdan C.

    1988-08-01

    The luminosity of the weak focusing self-collider (ESCOL) is intrinsically 10 8-10 10 times greater than that of conventional colliding beams, due to the product of the solid angle factor, ˜10 6, and the neutralization factor, ˜10 2 -10 4. We extrapolate to 10-GeV protons the parameters of a recent low energy experiment demonstrating that a 1-MeV deuteron beam, stored in ESCOL as migma, can be neutralized bo oscillating electrons and operate an order of magnitude above the space charge limit without instabilities. With the number density achieved in ESCOL, n = 3.2 × 10 9 ions cm -3, such a relativistic strong focusing self-collider (XYDER) would have a luminosity L ˜ 10 38 cm -2 s -1 for 10-GeV-on-10-GeV protons (equivalent to 250 GeV beam-on-target). At the diamagnetic "limit" density, which for 10 tesla is n = 10 12 ions cm -3, l ˜ 10 43 cm -2 s -1; this would produce 4 × 10 16 antiprotons/s (2 gram of overlinep/year). Other particles, rare nuclei, and rare effects produced with micro- (10 -16), nano- (10 -9 b), and picoscopic (10 -12 b) cross sections will be macro-produced in XYDER. A newly proposed annular magnet would provide a large volume of stored, V = 10 9 cm 3, as well as automatic ejection along the +z and -z axes of the overlinep's and other particles whose momentum is lower than that of the primary proton migma. Antiprotons, being produced with low rapidity, will have energies below 1 GeV in COM, and thus are suitable for beaming, extraction, cooling, abd slowing down to be either stored for space propulsion or used as a source for acceleration. If the magnetic field strength is adjusted for the antiprotons to be confined, an unusual plasma will be formed, consisting of the protons, antiprotons, electrons, and positrons (from pion-muon-electron decays), and similar to Alfvèns "ambiplasman". Its plasmic beta will be unity already at low densities (˜10 11 cm -3 where ωpi/ ωci ≤ 1); the ion-to-electron "temperature" ratio will never achieve

  12. Modified MBE hardware and techniques and role of gallium purity for attainment of two dimensional electron gas mobility >35×106 cm2/V s in AlGaAs/GaAs quantum wells grown by MBE

    NASA Astrophysics Data System (ADS)

    Gardner, Geoffrey C.; Fallahi, Saeed; Watson, John D.; Manfra, Michael J.

    2016-05-01

    We provide evidence that gallium purity is the primary impediment to attainment of ultra-high mobility in a two-dimensional electron gas (2DEG) in AlGaAs/GaAs heterostructures grown by molecular beam epitaxy (MBE). The purity of gallium can be enhanced dramatically by in-situ high temperature outgassing within an operating MBE. Based on analysis of data from an initial growth campaign in a new MBE system and modifications employed for a 2nd growth campaign, we have produced 2DEGs with low temperature mobility μ in excess of 35×106 cm2/V s at density n=3.0×1011/cm2 and μ=18×106 cm2/V s at n=1.1×1011/cm2. Our 2nd campaign data indicate that gallium purity remains the factor currently limiting μ<40×106 cm2/V s. We describe strategies to overcome this limitation.

  13. Photon absorptiometry

    SciTech Connect

    Velchik, M.G.

    1987-01-01

    Recently, there has been a renewed interest in the detection and treatment of osteoporosis. This paper is a review of the merits and limitations of the various noninvasive modalities currently available for the measurement of bone mineral density with special emphasis placed upon the nuclear medicine techniques of single-photon and dual-photon absorptiometry. The clinicians should come away with an understanding of the relative advantages and disadvantages of photon absorptiometry and its optimal clinical application. 49 references.

  14. Scalable high-power (>1kW/cm^2) diode laser stacks based on silicon monolithic micro-channel coolers

    NASA Astrophysics Data System (ADS)

    Reichert, Patrick; Fouksman, Michael; Zhou, Hailong; Nabors, David; Alcala, Jiro; Tolman, Sherry; Toivonen, Mika; Lehkonen, Sami; Haapamaa, Jouko

    2007-02-01

    We describe the performance and reliability of high power vertical diode stacks based on silicon monolithic microchannel coolers (SiMMs) operating at >1000W/cm2 CW at 808 and 940nm. The monolithic nature of these stacks makes them inherently robust and compact. Typical emitting dimensions for a 10-bar stack are ~8.8mm × 10mm with CW output power up to 1.5kW. Originally developed at Lawrence Livermore National Laboratory and now actively being developed for commercial applications at Coherent, this technology offers several advantages over current copper-based micro-channel coolers. These devices do not require use of DI water, strict monitoring and control of the pH level, careful control of the water velocity, or sealed cooling systems. The need for hydrostatic seals is also drastically reduced. A typical ten bar stack requires only 2 o-ring seals, compared to 20 such seals for a similar stack using copper microchannel cooling. Mature and readily available wet etching technology allows for cost effective batch fabrication of the sub-mount structure while achieving repeatable high precision components based on photolithographic fabrication processes.

  15. Performance of a 64-channel, 3.2×3.2 cm2 SiPM tile for TOF-PET application

    NASA Astrophysics Data System (ADS)

    Ferri, Alessandro; Acerbi, Fabio; Gola, Alberto; Piemonte, Claudio; Paternoster, Giovanni; Zorzi, Nicola

    2016-07-01

    In this work, we present a new 3.2×3.2 cm2 detector tile, composed of 8×8 single SiPMs, having a regular 4 mm pitch in both the X and Y directions. The tile fill factor is 85%. We produced two versions of the tile with different SiPM technologies: RGB-HD and NUV. The first one features square micro-cells with 25 μm pitch, a PDE peaked at 550 nm and a DCR of 300 kHz/mm2, at 20 °C and at maximum detection efficiency. The second one features micro-cells with 40 μm pitch and a PDE peaked in the blue part of the spectrum. The dark count rate at 20 °C and at maximum PDE is 100 kHz/mm2. In this work, we show the energy and timing resolution measurements at 511 keV obtained coupling the two tiles to an 8×8 LYSO array with a pixel size of 4×4×22 mm3, perfectly matching the photo-detector array.

  16. Nanostructured multielement (TiHfZrNbVTa)N coatings before and after implantation of N+ ions (1018 cm-2): Their structure and mechanical properties

    NASA Astrophysics Data System (ADS)

    Pogrebnjak, A. D.; Bondar, O. V.; Borba, S. O.; Abadias, G.; Konarski, P.; Plotnikov, S. V.; Beresnev, V. M.; Kassenova, L. G.; Drodziel, P.

    2016-10-01

    Multielement high entropy alloy (HEA) nitride (TiHfZrNbVTa)N coatings were deposited by vacuum arc and their structural and mechanical stability after implantation of high doses of N+ ions, 1018 cm-2, were investigated. The crystal structure and phase composition were characterized by X-ray diffraction (XRD) and Transmission Electron Microscopy, while depth-resolved nanoindentation tests were used to determine the evolution of hardness and elastic modulus along the implantation depth. XRD patterns show that coatings exhibit a main phase with fcc structure, which preferred orientation varies from (1 1 1) to (2 0 0), depending on the deposition conditions. First-principles calculations reveal that the presence of Nb atoms could favor the formation of solid solution with fcc structure in multielement HEA nitride. TEM results showed that amorphous and nanostructured phases were formed in the implanted coating sub-surface layer (∼100 nm depth). Concentration of nitrogen reached 90 at% in the near-surface layer after implantation, and decreased at higher depth. Nanohardness of the as-deposited coatings varied from 27 to 38 GPa depending on the deposition conditions. Ion implantation led to a significant decrease of the nanohardness to 12 GPa in the implanted region, while it reaches 24 GPa at larger depths. However, the H/E ratio is ⩾0.1 in the sub-surface layer due to N+ implantation, which is expected to have beneficial effect on the wear properties.

  17. Characterization of thin pixel sensor modules interconnected with SLID technology irradiated to a fluence of 2ṡ1015 neq/cm2.

    NASA Astrophysics Data System (ADS)

    Weigell, P.; Andricek, L.; Beimforde, M.; Macchiolo, A.; Moser, H.-G.; Nisius, R.; Richter, R.-H.

    2011-12-01

    A new module concept for future ATLAS pixel detector upgrades is presented, where thin n-in-p silicon sensors are connected to the front-end chip exploiting the novel Solid Liquid Interdiffusion technique (SLID) and the signals are read out via Inter Chip Vias (ICV) etched through the front-end. This should serve as a proof of principle for future four-side buttable pixel assemblies for the ATLAS upgrades, without the cantilever presently needed in the chip for the wire bonding. The SLID interconnection, developed by the Fraunhofer EMFT, is a possible alternative to the standard bump-bonding. It is characterized by a very thin eutectic Cu-Sn alloy and allows for stacking of different layers of chips on top of the first one, without destroying the pre-existing bonds. This paves the way for vertical integration technologies. Results of the characterization of the first pixel modules interconnected through SLID as well as of one sample irradiated to 2ṡ1015 neq/cm2 are discussed. Additionally, the etching of ICV into the front-end wafers was started. ICVs will be used to route the signals vertically through the front-end chip, to newly created pads on the backside. In the EMFT approach the chip wafer is thinned to (50-60) μm.

  18. Membraneless, room-temperature, direct borohydride/cerium fuel cell with power density of over 0.25 W/cm2.

    PubMed

    Da Mota, Nicolas; Finkelstein, David A; Kirtland, Joseph D; Rodriguez, Claudia A; Stroock, Abraham D; Abruña, Héctor D

    2012-04-11

    The widespread adoption and deployment of fuel cells as an alternative energy technology have been hampered by a number of formidable technical challenges, including the cost and long-term stability of electrocatalyst and membrane materials. We present a microfluidic fuel cell that overcomes many of these obstacles while achieving power densities in excess of 250 mW/cm(2). The poisoning and sluggish reaction rate associated with CO-contaminated H(2) and methanol, respectively, are averted by employing the promising, high-energy density fuel borohydride. The high-overpotential reaction of oxygen gas at the cathode is supplanted by the high-voltage reduction of cerium ammonium nitrate. Expensive, ineffective membrane materials are replaced with laminar flow and a nonselective, porous convection barrier to separate the fuel and oxidant streams. The result is a Nafion-free, room-temperature fuel cell that has the highest power density per unit mass of Pt catalyst employed for a non-H(2) fuel cell, and exceeds the power density of a typical H(2) fuel cell by 50%.

  19. Aging characteristics of blue InGaN micro-light emitting diodes at an extremely high current density of 3.5 kA cm-2

    NASA Astrophysics Data System (ADS)

    Tian, Pengfei; Althumali, Ahmad; Gu, Erdan; Watson, Ian M.; Dawson, Martin D.; Liu, Ran

    2016-04-01

    The aging characteristics of blue InGaN micro-light emitting diodes (micro-LEDs) with different sizes have been studied at an extremely high current density 3.5 kA cm-2 for emerging micro-LED applications including visible light communication (VLC), micro-LED pumped organic lasers and optogenetics. The light output power of micro-LEDs first increases and then decreases due to the competition of Mg activation in p-GaN layer and defect generation in the active region. The smaller micro-LEDs show less light output power degradation compared with larger micro-LEDs, which is attributed to the lower junction temperature of smaller micro-LEDs. It is found that the high current density without additional junction temperature cannot induce significant micro-LED degradation at room temperature but the combination of the high current density and high junction temperature leads to strong degradation. Furthermore, the cluster LEDs, composed of a micro-LED array, have been developed with both high light output power and less light output degradation for micro-LED applications in solid state lighting and VLC.

  20. Mercury thiogallate nanosecond optical parametric oscillator continuously tunable from 4.2 to 10.8 μm

    NASA Astrophysics Data System (ADS)

    Kostyukova, N. Yu; Kolker, D. B.; Zenov, K. G.; Boyko, A. A.; Starikova, M. K.; Sherstov, I. V.; Karapuzikov, A. A.

    2015-09-01

    We demonstrate an optical parametric oscillator based on two HgGa2S4 crystals with an extremely wide tuning range from 4.2 to 10.8 μm. The HgGa2S4 optical parametric oscillator was pumped by a Q-switched nanosecond Nd : YLF laser at 1.053 μm. The absorption spectrum of ammonia was presented to demonstrate the feasibility of the developed optical parametric oscillator system for spectroscopic measurements and gas detection.

  1. The photon

    NASA Astrophysics Data System (ADS)

    Collins, Russell L.

    2009-10-01

    There are no TEM waves, only photons. Lets build a photon, using a radio antenna. A short antenna (2L<< λ) simplifies the calculation, letting B fall off everywhere as 1/r^2. The Biot-Savart law finds B = (μ0/4π)(LI0/r^2)θφt. The magnetic flux thru a semi-circle of radius λ/2 is set equal to the flux quantum h/e, determining the needed source strength, LI0. From this, one can integrate the magnetic energy density over a sphere of radius λ/2 and finds it to be 1.0121 hc/λ. Pretty close. A B field collapses when the current ceases, but the photon evades this by creating a ɛ0E / t displacement current at center that fully supports the toroidal B assembly as it moves at c. This E=vxB arises because the photon moves at c. Stopped, a photon decays. At every point along the photon's path, an observer will note a transient oscillation of an E field. This sources the EM ``guiding wave'', carrying little or no energy and expanding at c. At the head of the photon, all these spherical guiding waves gather ``in-phase'' as a planar wavefront. This model speaks to all the many things we know about light. The photon is tiny, but its guiding wave is huge.

  2. Investigation of rat bone fracture healing using pulsed 1.5 MHz, 30 mW/cm(2) burst ultrasound--axial distance dependency.

    PubMed

    Fung, Chak-Hei; Cheung, Wing-Hoi; Pounder, Neill M; de Ana, F Javier; Harrison, Andrew; Leung, Kwok-Sui

    2014-03-01

    This study investigated the effect of LIPUS on fracture healing when fractures were exposed to ultrasound at three axial distances: z=0 mm, 60 mm, and 130 mm. We applied LIPUS to rat fracture at these three axial distances mimicking the exposure condition of human fractures at different depths under the soft tissue. Measurement of LIPUS shows pressure variations in near field (nearby transducer); uniform profile was found beyond it (far field). We asked whether different positions of the fracture within the ultrasound field cause inconsistent biological effect during the healing process. Closed femoral fractured Sprague-Dawley rats were randomized into control, near-field (0mm), mid-near field (60 mm) or far-field (130 mm) groups. Daily LIPUS treatment (plane, but apodized source, see details in the text; 2.2 cm in diameter; 1.5 MHz sine waves repeating at 1 kHz PRF; spatial average temporal average intensity, ISATA=30 mW/cm(2)) was given to fracture site at the three axial distances. Weekly radiographs and endpoint microCT, histomorphometry, and mechanical tests were performed. The results showed that the 130 mm group had the highest tissue mineral density; and significantly higher mechanical properties than control at week 4. The 60 mm and 0 mm groups had significantly higher (i.e. p<0.05) woven bone percentage than control group in radiological, microCT and histomorphometry measurements. In general, LIPUS at far field augmented callus mineralization and mechanical properties; while near field and mid-near field enhanced woven bone formation. Our results indicated the therapeutic effect of LIPUS is dependent on the axial distance of the ultrasound beam. Therefore, the depth of fracture under the soft tissue affects the biological effect of LIPUS. Clinicians have to be aware of the fracture depth when LIPUS is applied transcutaneously.

  3. Blisters on the Anterior Shin in 3 Research Subjects After a 1-MHz, 1.5-W/cm 2, Continuous Ultrasound Treatment: A Case Series

    PubMed Central

    Frye, Jamie L; Johns, Lennart D; Tom, James A; Ingersoll, Christopher D

    2007-01-01

    Context: Clinicians should consider multiple factors when estimating tissue-heating rates. Objective: To report 3 separate occurrences of blisters during an ultrasound treatment experiment. Background: While we were conducting a research experiment comparing the measurement capabilities of 2 different intramuscular temperature devices, 3 female participants (age = 26.33 ± 3.79 years, height = 169.34 ± 3.89 cm, mass = 63.39 ± 3.81 kg) out of 16 healthy volunteers (7 men: age = 22.83 ± 1.17 years, height = 170.61 ± 7.77 cm, mass = 74.62 ± 19.24 kg; 9 women: age = 24.22 ± 2.73 years, height = 171.88 ± 6.35 cm, mass = 73.99 ± 18.55 kg) developed blisters on the anterior shin after a 1-MHz, 1.5-W/cm 2 continuous ultrasound treatment delivered to the triceps surae muscle. Differential Diagnosis: Allergies; chemical reaction with cleaning agents; sunburn; negative interaction between the temperature measurement instruments and the ultrasound field; the ultrasound transducer not being calibrated properly, producing a nonuniform field and creating a hot spot or heating differently when compared with other ultrasound devices; the smaller anatomy of our female subjects; or a confounding interaction among these factors. Treatment: Participants were given standard minor burn care by a physician. Uniqueness: (1) The development of blisters on the anterior aspect of the shin as a result of an ultrasound treatment to the posterior aspect of the triceps surae muscle and (2) muscle tissue heating rates ranging from 0.19°C to 1.1°C/min, when ultrasound researchers have suggested tissue heating in the range of 0.3°C/min with these settings. Conclusions: These adverse events raise important questions regarding treatment application and potential differences in heating and quality control among different ultrasound devices from different manufacturers. PMID:18060000

  4. One-year Outcomes of Pachymetry and Epithelium Thicknesses after Accelerated (45 mW/cm(2)) Transepithelial Corneal Collagen Cross-linking for Keratoconus Patients.

    PubMed

    Zhang, Xiaoyu; Sun, Ling; Chen, Yingjun; Li, Meiyan; Tian, Mi; Zhou, Xingtao

    2016-01-01

    The thickness of corneal pachymetry and the epithelium after accelerated (45 mW/cm(2)) transepithelial corneal collagen cross-linking (CXL) for keratoconus were assessed in this prospective case series study. Twenty-eight patients were treated for keratoconus. The mean Kmax was 56.18 ± 7.90. The thinnest point, as assessed by optical coherence tomography (OCT), was 443.18 ± 39.75 μm. Accelerated transepithelial CXL was performed, and corrected distance visual acuity (CDVA), corneal topography, and OCT were recorded at 1 week postoperatively as well as at 1, 3, 6, and 12 months. The surgery was uneventful in all eyes. Postoperative epithelial edema was observed and faded in 3 days. The postoperative Kmax was 54.56 ± 8.81, 55.78 ± 8.11, 56.37 ± 8.71, 55.80 ± 7.92, and 55.47 ± 8.24 at 1 week, 1 month, 3 months, 6 months, and 12 months, respectively (all, P > 0.05). The thinnest postoperative corneal point, 439.04 ± 44.99 μm, was observed at 12 months (P = 0.109). The epithelial thickness decreased during the first postoperative week then showed a gradual recovery. Postoperative pachymetry thickness showed no significant changes for up to 12 months. Postoperative epithelial thickness decreased temporarily, then stabilized at month 12. Accelerated transepithelial CXL was shown to be effective and safe for the treatment of keratoconus. PMID:27597655

  5. Hydrogen and carbon isotopic ratios of polycyclic aromatic compounds in two CM2 carbonaceous chondrites and implications for prebiotic organic synthesis

    NASA Astrophysics Data System (ADS)

    Huang, Yongsong; Aponte, José C.; Zhao, Jiaju; Tarozo, Rafael; Hallmann, Christian

    2015-09-01

    Study of meteoritic organic compounds offers a unique opportunity to understand the origins of the organic matter in the early Solar System. Meteoritic polycyclic aromatic hydrocarbons (PAHs) and heteropolycyclic aromatic compounds (HACs) have been studied for over fifty years, however; their hydrogen stable isotopic ratios (δD) have never been reported. Compound-specific δD measurements of PAHs and HACs are important, in part because the carbon isotopic ratios (δ13C) of various meteoritic PAHs cannot be readily distinguished from their terrestrial counterparts and it is difficult to rule out terrestrial contamination based on carbon isotopic ratios alone. In this study, we have extracted and identified more than sixty PAHs and HACs present in two CM2 carbonaceous chondrites Murchison and LON 94101. Their carbon and hydrogen stable isotopic ratios (δ13C and δD) were measured and used to discuss about their synthetic environments and formation mechanisms. The concentration of aromatic compounds is ∼30% higher in Murchison than in the Antarctic meteorite LON 94101, but both samples contained similar suites of PAHs and HACs. All PAHs and HACs found exhibited positive δD values (up to 1100‰) consistent with an extraterrestrial origin, indicating the relatively low δ13C values are indeed an inherent feature of the meteoritic aromatic compounds. The hydrogen isotopic data suggest aromatic compounds in carbonaceous chondrites were mainly formed in the cold interstellar environments. Molecular level variations in hydrogen and carbon isotopic values offer new insights to the formation pathways for the aromatic compounds in carbonaceous chondrites.

  6. Aqueous Alteration of Carbonaceous Chondrites: New Insights from Comparative Studies of Two Unbrecciated CM2 Chondrites, Y 791198 and ALH 81002

    NASA Technical Reports Server (NTRS)

    Chizmadia, L. J.; Brearley, A. J.

    2004-01-01

    Carbonaceous chondrites are an important resource for understanding the physical and chemical conditions in the early solar system. In particular, a long-standing question concerns the role of water in the cosmochemical evolution of carbonaceous chondrites. It is well established that extensive hydration of primary nebular phases occurred in the CM and CI chondrites, but the location where this alteration occurred remains controversial. In the CM2 chondrites, hydration formed secondary phases such as serpentine, tochilinite, pentlandite, carbonate and PCP. There are several textural observations which suggest that alteration occurred before the accretion of the final CM parent asteroid, i.e. preaccretionary alteration. Conversely, there is a significant body of evidence that supports parent-body alteration. In order to test these two competing hypotheses further, we studied two CM chondrites, Y-791198 and ALH81002, two meteorites that exhibit widely differing degrees of aqueous alteration. In addition, both meteorites have primary accretionary textures, i.e. experienced minimal asteroidal brecciation. Brecciation significantly complicates the task of unraveling alteration histories, mixing components that have been altered to different degrees from different locations on the same asteroidal parent body. Alteration in Y-791198 is mostly confined to chondrule mesostases, FeNi metal and fine-grained matrix and rims. In comparison, the primary chondrule silicates in ALH81002 have undergone extensive replacement by secondary hydrous phases. This study focuses on compositional and textural relationships between chondrule mesostasis and the associated rim materials. Our hypothesis is: both these components are highly susceptible to aqueous alteration and should be sensitive recorders of the alteration process. For parent body alteration, we expect systematic coupled mineralogical and compositional changes in rims and altered mesostasis, as elemental exchange between these

  7. Investigation of rat bone fracture healing using pulsed 1.5 MHz, 30 mW/cm(2) burst ultrasound--axial distance dependency.

    PubMed

    Fung, Chak-Hei; Cheung, Wing-Hoi; Pounder, Neill M; de Ana, F Javier; Harrison, Andrew; Leung, Kwok-Sui

    2014-03-01

    This study investigated the effect of LIPUS on fracture healing when fractures were exposed to ultrasound at three axial distances: z=0 mm, 60 mm, and 130 mm. We applied LIPUS to rat fracture at these three axial distances mimicking the exposure condition of human fractures at different depths under the soft tissue. Measurement of LIPUS shows pressure variations in near field (nearby transducer); uniform profile was found beyond it (far field). We asked whether different positions of the fracture within the ultrasound field cause inconsistent biological effect during the healing process. Closed femoral fractured Sprague-Dawley rats were randomized into control, near-field (0mm), mid-near field (60 mm) or far-field (130 mm) groups. Daily LIPUS treatment (plane, but apodized source, see details in the text; 2.2 cm in diameter; 1.5 MHz sine waves repeating at 1 kHz PRF; spatial average temporal average intensity, ISATA=30 mW/cm(2)) was given to fracture site at the three axial distances. Weekly radiographs and endpoint microCT, histomorphometry, and mechanical tests were performed. The results showed that the 130 mm group had the highest tissue mineral density; and significantly higher mechanical properties than control at week 4. The 60 mm and 0 mm groups had significantly higher (i.e. p<0.05) woven bone percentage than control group in radiological, microCT and histomorphometry measurements. In general, LIPUS at far field augmented callus mineralization and mechanical properties; while near field and mid-near field enhanced woven bone formation. Our results indicated the therapeutic effect of LIPUS is dependent on the axial distance of the ultrasound beam. Therefore, the depth of fracture under the soft tissue affects the biological effect of LIPUS. Clinicians have to be aware of the fracture depth when LIPUS is applied transcutaneously. PMID:24239510

  8. One-year Outcomes of Pachymetry and Epithelium Thicknesses after Accelerated (45 mW/cm2) Transepithelial Corneal Collagen Cross-linking for Keratoconus Patients

    PubMed Central

    Zhang, Xiaoyu; Sun, Ling; Chen, Yingjun; Li, Meiyan; Tian, Mi; Zhou, Xingtao

    2016-01-01

    The thickness of corneal pachymetry and the epithelium after accelerated (45 mW/cm2) transepithelial corneal collagen cross-linking (CXL) for keratoconus were assessed in this prospective case series study. Twenty-eight patients were treated for keratoconus. The mean Kmax was 56.18 ± 7.90. The thinnest point, as assessed by optical coherence tomography (OCT), was 443.18 ± 39.75 μm. Accelerated transepithelial CXL was performed, and corrected distance visual acuity (CDVA), corneal topography, and OCT were recorded at 1 week postoperatively as well as at 1, 3, 6, and 12 months. The surgery was uneventful in all eyes. Postoperative epithelial edema was observed and faded in 3 days. The postoperative Kmax was 54.56 ± 8.81, 55.78 ± 8.11, 56.37 ± 8.71, 55.80 ± 7.92, and 55.47 ± 8.24 at 1 week, 1 month, 3 months, 6 months, and 12 months, respectively (all, P > 0.05). The thinnest postoperative corneal point, 439.04 ± 44.99 μm, was observed at 12 months (P = 0.109). The epithelial thickness decreased during the first postoperative week then showed a gradual recovery. Postoperative pachymetry thickness showed no significant changes for up to 12 months. Postoperative epithelial thickness decreased temporarily, then stabilized at month 12. Accelerated transepithelial CXL was shown to be effective and safe for the treatment of keratoconus. PMID:27597655

  9. Determining temperature distribution in tissue in the focal plane of the high (>100 W/cm(2)) intensity focused ultrasound beam using phase shift of ultrasound echoes.

    PubMed

    Karwat, Piotr; Kujawska, Tamara; Lewin, Peter A; Secomski, Wojciech; Gambin, Barbara; Litniewski, Jerzy

    2016-02-01

    In therapeutic applications of High Intensity Focused Ultrasound (HIFU) the guidance of the HIFU beam and especially its focal plane is of crucial importance. This guidance is needed to appropriately target the focal plane and hence the whole focal volume inside the tumor tissue prior to thermo-ablative treatment and beginning of tissue necrosis. This is currently done using Magnetic Resonance Imaging that is relatively expensive. In this study an ultrasound method, which calculates the variations of speed of sound in the locally heated tissue volume by analyzing the phase shifts of echo-signals received by an ultrasound scanner from this very volume is presented. To improve spatial resolution of B-mode imaging and minimize the uncertainty of temperature estimation the acoustic signals were transmitted and received by 8 MHz linear phased array employing Synthetic Transmit Aperture (STA) technique. Initially, the validity of the algorithm developed was verified experimentally in a tissue-mimicking phantom heated from 20.6 to 48.6 °C. Subsequently, the method was tested using a pork loin sample heated locally by a 2 MHz pulsed HIFU beam with focal intensity ISATA of 129 W/cm(2). The temperature calibration of 2D maps of changes in the sound velocity induced by heating was performed by comparison of the algorithm-determined changes in the sound velocity with the temperatures measured by thermocouples located in the heated tissue volume. The method developed enabled ultrasound temperature imaging of the heated tissue volume from the very inception of heating with the contrast-to-noise ratio of 3.5-12 dB in the temperature range 21-56 °C. Concurrently performed, conventional B-mode imaging revealed CNR close to zero dB until the temperature reached 50 °C causing necrosis. The data presented suggest that the proposed method could offer an alternative to MRI-guided temperature imaging for prediction of the location and extent of the thermal lesion prior to applying the

  10. Determining temperature distribution in tissue in the focal plane of the high (>100 W/cm(2)) intensity focused ultrasound beam using phase shift of ultrasound echoes.

    PubMed

    Karwat, Piotr; Kujawska, Tamara; Lewin, Peter A; Secomski, Wojciech; Gambin, Barbara; Litniewski, Jerzy

    2016-02-01

    In therapeutic applications of High Intensity Focused Ultrasound (HIFU) the guidance of the HIFU beam and especially its focal plane is of crucial importance. This guidance is needed to appropriately target the focal plane and hence the whole focal volume inside the tumor tissue prior to thermo-ablative treatment and beginning of tissue necrosis. This is currently done using Magnetic Resonance Imaging that is relatively expensive. In this study an ultrasound method, which calculates the variations of speed of sound in the locally heated tissue volume by analyzing the phase shifts of echo-signals received by an ultrasound scanner from this very volume is presented. To improve spatial resolution of B-mode imaging and minimize the uncertainty of temperature estimation the acoustic signals were transmitted and received by 8 MHz linear phased array employing Synthetic Transmit Aperture (STA) technique. Initially, the validity of the algorithm developed was verified experimentally in a tissue-mimicking phantom heated from 20.6 to 48.6 °C. Subsequently, the method was tested using a pork loin sample heated locally by a 2 MHz pulsed HIFU beam with focal intensity ISATA of 129 W/cm(2). The temperature calibration of 2D maps of changes in the sound velocity induced by heating was performed by comparison of the algorithm-determined changes in the sound velocity with the temperatures measured by thermocouples located in the heated tissue volume. The method developed enabled ultrasound temperature imaging of the heated tissue volume from the very inception of heating with the contrast-to-noise ratio of 3.5-12 dB in the temperature range 21-56 °C. Concurrently performed, conventional B-mode imaging revealed CNR close to zero dB until the temperature reached 50 °C causing necrosis. The data presented suggest that the proposed method could offer an alternative to MRI-guided temperature imaging for prediction of the location and extent of the thermal lesion prior to applying the

  11. Diffuse neutrino intensity from the inner jets of active galactic nuclei: Impacts of external photon fields and the blazar sequence

    NASA Astrophysics Data System (ADS)

    Murase, Kohta; Inoue, Yoshiyuki; Dermer, Charles D.

    2014-07-01

    We study high-energy neutrino production in inner jets of radio-loud active galactic nuclei (AGN), taking into account effects of external photon fields and the blazar sequence. We show that the resulting diffuse neutrino intensity is dominated by quasar-hosted blazars, in particular, flat spectrum radio quasars, and that PeV-EeV neutrino production due to photohadronic interactions with broadline and dust radiation is unavoidable if the AGN inner jets are ultrahigh-energy cosmic-ray (UHECR) sources. Their neutrino spectrum has a cutoff feature around PeV energies since target photons are due to Lyα emission. Because of infrared photons provided by the dust torus, neutrino spectra above PeV energies are too hard to be consistent with the IceCube data unless the proton spectral index is steeper than 2.5, or the maximum proton energy is ≲100 PeV. Thus, the simple model has difficulty in explaining the IceCube data. For the cumulative neutrino intensity from blazars to exceed ˜10-8 GeV cm-2 s-1 sr-1, their local cosmic-ray energy generation rate would be ˜10-100 times larger than the local UHECR emissivity but is comparable to the averaged γ-ray blazar emissivity. Interestingly, future detectors such as the Askaryan Radio Array can detect ˜0.1-1 EeV neutrinos even in more conservative cases, allowing us to indirectly test the hypothesis that UHECRs are produced in the inner jets. We find that the diffuse neutrino intensity from radio-loud AGN is dominated by blazars with γ-ray luminosity of ≳1048 erg s-1, and the arrival directions of their ˜1-100 PeV neutrinos correlate with the luminous blazars detected by Fermi.

  12. Photon generator

    DOEpatents

    Srinivasan-Rao, Triveni

    2002-01-01

    A photon generator includes an electron gun for emitting an electron beam, a laser for emitting a laser beam, and an interaction ring wherein the laser beam repetitively collides with the electron beam for emitting a high energy photon beam therefrom in the exemplary form of x-rays. The interaction ring is a closed loop, sized and configured for circulating the electron beam with a period substantially equal to the period of the laser beam pulses for effecting repetitive collisions.

  13. Unveiling the Gamma-Ray Source Count Distribution Below the Fermi Detection Limit with Photon Statistics

    NASA Astrophysics Data System (ADS)

    Zechlin, Hannes-S.; Cuoco, Alessandro; Donato, Fiorenza; Fornengo, Nicolao; Vittino, Andrea

    2016-08-01

    The source-count distribution as a function of their flux, {dN}/{dS}, is one of the main quantities characterizing gamma-ray source populations. We employ statistical properties of the Fermi Large Area Telescope (LAT) photon counts map to measure the composition of the extragalactic gamma-ray sky at high latitudes (| b| ≥slant 30°) between 1 and 10 GeV. We present a new method, generalizing the use of standard pixel-count statistics, to decompose the total observed gamma-ray emission into (a) point-source contributions, (b) the Galactic foreground contribution, and (c) a truly diffuse isotropic background contribution. Using the 6 yr Fermi-LAT data set (P7REP), we show that the {dN}/{dS} distribution in the regime of so far undetected point sources can be consistently described with a power law with an index between 1.9 and 2.0. We measure {dN}/{dS} down to an integral flux of ˜ 2× {10}-11 {{cm}}-2 {{{s}}}-1, improving beyond the 3FGL catalog detection limit by about one order of magnitude. The overall {dN}/{dS} distribution is consistent with a broken power law, with a break at {2.1}-1.3+1.0× {10}-8 {{cm}}-2 {{{s}}}-1. The power-law index {n}1={3.1}-0.5+0.7 for bright sources above the break hardens to {n}2=1.97+/- 0.03 for fainter sources below the break. A possible second break of the {dN}/{dS} distribution is constrained to be at fluxes below 6.4× {10}-11 {{cm}}-2 {{{s}}}-1 at 95% confidence level. The high-latitude gamma-ray sky between 1 and 10 GeV is shown to be composed of ˜25% point sources, ˜69.3% diffuse Galactic foreground emission, and ˜6% isotropic diffuse background.

  14. Photonic lanterns

    NASA Astrophysics Data System (ADS)

    Leon-Saval, Sergio G.; Argyros, Alexander; Bland-Hawthorn, Joss

    2013-12-01

    Multimode optical fibers have been primarily (and almost solely) used as "light pipes" in short distance telecommunications and in remote and astronomical spectroscopy. The modal properties of the multimode waveguides are rarely exploited and mostly discussed in the context of guiding light. Until recently, most photonic applications in the applied sciences have arisen from developments in telecommunications. However, the photonic lantern is one of several devices that arose to solve problems in astrophotonics and space photonics. Interestingly, these devices are now being explored for use in telecommunications and are likely to find commercial use in the next few years, particularly in the development of compact spectrographs. Photonic lanterns allow for a low-loss transformation of a multimode waveguide into a discrete number of single-mode waveguides and vice versa, thus enabling the use of single-mode photonic technologies in multimode systems. In this review, we will discuss the theory and function of the photonic lantern, along with several different variants of the technology. We will also discuss some of its applications in more detail. Furthermore, we foreshadow future applications of this technology to the field of nanophotonics.

  15. Behavior of welds in liquid lead containing 10-6 wt% and 10-8 wt% oxygen

    NASA Astrophysics Data System (ADS)

    Heinzel, A.; Müller, G.; Weisenburger, A.

    2013-06-01

    Specimens with welded joints of P91 TIG (tungsten inert gas welding), P91 EB (electron beam welding) and frictions stir welding, with P92 (EB), PM2000 (EB) and combination of P91-PM2000 EB were tested 2000 h in stagnant liquid Pb at 550 °C with an oxygen concentration of 10-6 wt% and 10-8 wt%. After exposure at 10-6 wt% all specimens showed an oxide layer on the surface. If the grain size of the welds varies strongly from that of the bulk material like in the friction stir welds, a change in oxide thickness could be observed. Also precipitations which pin the oxide formers or reduce the diffusion rate can lead to thicker oxide layers or a stronger dissolution attack like it was observed on the dissimilar weld P91/PM2000 EB. The specimens have similar microstructures in all regions (weld, heat affected zone and bulk material) and due to a post-weld heat treatment show everywhere the same behavior.

  16. Vesicle Photonics

    SciTech Connect

    Vasdekis, Andreas E.; Scott, E. A.; Roke, Sylvie; Hubbell, J. A.; Psaltis, D.

    2013-04-03

    Thin membranes, under appropriate boundary conditions, can self-assemble into vesicles, nanoscale bubbles that encapsulate and hence protect or transport molecular payloads. In this paper, we review the types and applications of light fields interacting with vesicles. By encapsulating light-emitting molecules (e.g. dyes, fluorescent proteins, or quantum dots), vesicles can act as particles and imaging agents. Vesicle imaging can take place also under second harmonic generation from vesicle membrane, as well as employing mass spectrometry. Light fields can also be employed to transport vesicles using optical tweezers (photon momentum) or directly pertrurbe the stability of vesicles and hence trigger the delivery of the encapsulated payload (photon energy).

  17. Photons Revisited

    NASA Astrophysics Data System (ADS)

    Batic, Matej; Begalli, Marcia; Han, Min Cheol; Hauf, Steffen; Hoff, Gabriela; Kim, Chan Hyeong; Kim, Han Sung; Grazia Pia, Maria; Saracco, Paolo; Weidenspointner, Georg

    2014-06-01

    A systematic review of methods and data for the Monte Carlo simulation of photon interactions is in progress: it concerns a wide set of theoretical modeling approaches and data libraries available for this purpose. Models and data libraries are assessed quantitatively with respect to an extensive collection of experimental measurements documented in the literature to determine their accuracy; this evaluation exploits rigorous statistical analysis methods. The computational performance of the associated modeling algorithms is evaluated as well. An overview of the assessment of photon interaction models and results of the experimental validation are presented.

  18. Green photonics

    NASA Astrophysics Data System (ADS)

    Quan, Frederic

    2012-02-01

    Photonics, the broad merger of electronics with the optical sciences, encompasses such a wide swath of technology that its impact is almost universal in our everyday lives. This is a broad overview of some aspects of the industry and their contribution to the ‘green’ or environmental movement. The rationale for energy conservation is briefly discussed and the impact of photonics on our everyday lives and certain industries is described. Some opinions from industry are presented along with market estimates. References are provided to some of the most recent research in these areas.

  19. Modeling silicon diode energy response factors for use in therapeutic photon beams.

    PubMed

    Eklund, Karin; Ahnesjö, Anders

    2009-10-21

    Silicon diodes have good spatial resolution, which makes them advantageous over ionization chambers for dosimetry in fields with high dose gradients. However, silicon diodes overrespond to low-energy photons, that are more abundant in scatter which increase with large fields and larger depths. We present a cavity-theory-based model for a general response function for silicon detectors at arbitrary positions within photon fields. The model uses photon and electron spectra calculated from fluence pencil kernels. The incident photons are treated according to their energy through a bipartition of the primary beam photon spectrum into low- and high-energy components. Primary electrons from the high-energy component are treated according to Spencer-Attix cavity theory. Low-energy primary photons together with all scattered photons are treated according to large cavity theory supplemented with an energy-dependent factor K(E) to compensate for energy variations in the electron equilibrium. The depth variation of the response for an unshielded silicon detector has been calculated for 5 x 5 cm(2), 10 x 10 cm(2) and 20 x 20 cm(2) fields in 6 and 15 MV beams and compared with measurements showing that our model calculates response factors with deviations less than 0.6%. An alternative method is also proposed, where we show that one can use a correlation with the scatter factor to determine the detector response of silicon diodes with an error of less than 3% in 6 MV and 15 MV photon beams.

  20. Growth of ˜5 cm2V-1s-1 mobility, p-type Copper(I) oxide (Cu2O) films by fast atmospheric atomic layer deposition (AALD) at 225°C and below

    NASA Astrophysics Data System (ADS)

    Muñoz-Rojas, D.; Jordan, M.; Yeoh, C.; Marin, A. T.; Kursumovic, A.; Dunlop, L. A.; Iza, D. C.; Chen, A.; Wang, H.; MacManus Driscoll, J. L.

    2012-12-01

    Phase pure, dense Cu2O thin films were grown on glass and polymer substrates at 225°C by rapid atmospheric atomic layer deposition (AALD). Carrier mobilities of 5 cm2V-1s-1 and carrier concentrations of ˜1016 cm-3 were achieved in films of thickness 50 - 120 nm, over a >10 cm2 area. Growth rates were ˜1 nm.min-1 which is two orders of magnitude faster than conventional ALD.. The high mobilities achieved using the atmospheric, low temperature method represent a significant advance for flextronics and flexible solar cells which require growth on plastic substrates.

  1. Photon-photon collisions via relativisitic mirrors

    SciTech Connect

    Koga, James K.

    2012-07-11

    Photon-photon scattering at low energies has been predicted theoretically for many years. However, due to the extremely small cross section there has been no experimental confirmation of this. Due to the rapid increase in laser irradiances and projected peak irradiances in planned facilities regimes could be reached where photon-photon scattering could be experimentally observed. We will first review basic aspects of photon-photon collisions concentrating on the calculation of the photon-photon scattering cross section. Then we will discuss the possibilities for observing these phenomena in ultra-high irradiance laser-plasma interactions involving relativistic mirrors.

  2. Photon Collider Physics with Real Photon Beams

    SciTech Connect

    Gronberg, J; Asztalos, S

    2005-11-03

    Photon-photon interactions have been an important probe into fundamental particle physics. Until recently, the only way to produce photon-photon collisions was parasitically in the collision of charged particles. Recent advances in short-pulse laser technology have made it possible to consider producing high intensity, tightly focused beams of real photons through Compton scattering. A linear e{sup +}e{sup -} collider could thus be transformed into a photon-photon collider with the addition of high power lasers. In this paper they show that it is possible to make a competitive photon-photon collider experiment using the currently mothballed Stanford Linear Collider. This would produce photon-photon collisions in the GeV energy range which would allow the discovery and study of exotic heavy mesons with spin states of zero and two.

  3. Diverse Anhydrous Silicates in a Fine-Grained Rim in the Weakly Altered CM2 Chondrite Queen Elizabeth Range 97990: Evidence for the Localized Preservation of Pristine Nebular Dust in CM Chondrites.

    NASA Astrophysics Data System (ADS)

    Brearley, A. J.

    2016-08-01

    A fine-grained rim the QUE 97990 CM2 chondrite contains diverse submicron crystalline anhydrous silicates, including olivines, low-Ca and high Ca pyroxenes and represents a more pristine sample of nebular dust than is present in most CM chondrites.

  4. Low-level laser therapy, at 60 J/cm2 associated with a Biosilicate® increase in bone deposition and indentation biomechanical properties of callus in osteopenic rats

    NASA Astrophysics Data System (ADS)

    Fangel, Renan; Sérgio Bossini, Paulo; Cláudia Renno, Ana; Araki Ribeiro, Daniel; Chenwei Wang, Charles; Luri Toma, Renata; Okino Nonaka, Keico; Driusso, Patrícia; Antonio Parizotto, Nivaldo; Oishi, Jorge

    2011-07-01

    We investigate the effects of a novel bioactive material (Biosilicate®) and low-level laser therapy (LLLT), at 60 J/cm2, on bone-fracture consolidation in osteoporotic rats. Forty female Wistar rats are submitted to the ovariectomy, to induce osteopenia. Eight weeks after the ovariectomy, the animals are randomly divided into four groups, with 10 animals each: bone defect control group; bone defect filled with Biosilicate group; bone defect irradiated with laser at 60 J/cm2 group; bone defect filled with Biosilicate and irradiated with LLLT, at 60 J/cm2 group. Laser irradiation is initiated immediately after surgery and performed every 48 h for 14 days. Histopathological analysis points out that bone defects are predominantly filled with the biomaterial in specimens treated with Biosilicate. In the 60-J/cm2 laser plus Biosilicate group, the biomaterial fills all bone defects, which also contained woven bone and granulation tissue. Also, the biomechanical properties are increased in the animals treated with Biosilicate associated to lasertherapy. Our results indicate that laser therapy improves bone repair process in contact with Biosilicate as a result of increasing bone formation as well as indentation biomechanical properties.

  5. Microalgae photonics

    NASA Astrophysics Data System (ADS)

    Floume, Timmy; Coquil, Thomas; Sylvestre, Julien

    2011-05-01

    Due to their metabolic flexibility and fast growth rate, microscopic aquatic phototrophs like algae have a potential to become industrial photochemical converters. Algae photosynthesis could enable the large scale production of clean and renewable liquid fuels and chemicals with major environmental, economic and societal benefits. Capital and operational costs are the main issues to address through optical, process and biochemical engineering improvements. In this perspective, a variety of photonic approaches have been proposed - we introduce them here and describe their potential, limitations and compatibility with separate biotechnology and engineering progresses. We show that only sunlight-based approaches are economically realistic. One of photonics' main goals in the algae field is to dilute light to overcome photosaturation effects that impact upon cultures exposed to full sunlight. Among other approaches, we introduce a widely-compatible broadband spectral adaptation technique called AlgoSun® that uses luminescence to optimize sunlight spectrum in view of the bioconverter's requirements.

  6. Photon detectors

    SciTech Connect

    Va`vra, J.

    1995-10-01

    J. Seguinot and T. Ypsilantis have recently described the theory and history of Ring Imaging Cherenkov (RICH) detectors. In this paper, I will expand on these excellent review papers, by covering the various photon detector designs in greater detail, and by including discussion of mistakes made, and detector problems encountered, along the way. Photon detectors are among the most difficult devices used in physics experiments, because they must achieve high efficiency for photon transport and for the detection of single photo-electrons. For gaseous devices, this requires the correct choice of gas gain in order to prevent breakdown and wire aging, together with the use of low noise electronics having the maximum possible amplification. In addition, the detector must be constructed of materials which resist corrosion due to photosensitive materials such as, the detector enclosure must be tightly sealed in order to prevent oxygen leaks, etc. The most critical step is the selection of the photocathode material. Typically, a choice must be made between a solid (CsI) or gaseous photocathode (TMAE, TEA). A conservative approach favors a gaseous photocathode, since it is continuously being replaced by flushing, and permits the photon detectors to be easily serviced (the air sensitive photocathode can be removed at any time). In addition, it can be argued that we now know how to handle TMAE, which, as is generally accepted, is the best photocathode material available as far as quantum efficiency is concerned. However, it is a very fragile molecule, and therefore its use may result in relatively fast wire aging. A possible alternative is TEA, which, in the early days, was rejected because it requires expensive CaF{sub 2} windows, which could be contaminated easily in the region of 8.3 eV and thus lose their UV transmission.

  7. Photon Calorimeter

    DOEpatents

    Chow, Tze-Show

    1989-01-01

    A photon calorimeter (20, 40) is provided that comprises a laminar substrate (10, 22, 42) that is uniform in density and homogeneous in atomic composition. A plasma-sprayed coating (28, 48, 52), that is generally uniform in density and homogeneous in atomic composition within the proximity of planes that are parallel to the surfaces of the substrate, is applied to either one or both sides of the laminar substrate. The plasma-sprayed coatings may be very efficiently spectrally tailored in atomic number. Thermocouple measuring junctions (30, 50, 54) are positioned within the plasma-sprayed coatings. The calorimeter is rugged, inexpensive, and equilibrates in temperature very rapidly.

  8. Photon calorimeter

    DOEpatents

    Chow, Tze-Show

    1988-04-22

    A photon calorimeter is provided that comprises a laminar substrate that is uniform in density and homogeneous in atomic composition. A plasma-sprayed coating, that is generally uniform in density and homogeneous in atomic composition within the proximity of planes that are parallel to the surfaces of the substrate, is applied to either one or both sides of the laminar substrate. The plasma-sprayed coatings may be very efficiently spectrally tailored in atomic number. Thermocouple measuring junctions, are positioned within the plasma-sprayed coatings. The calorimeter is rugged, inexpensive, and equilibrates in temperature very rapidly. 4 figs.

  9. Radiation hardness test of the Philips Digital Photon Counter with proton beam

    NASA Astrophysics Data System (ADS)

    Barnyakov, M. Yu.; Frach, T.; Kononov, S. A.; Kuyanov, I. A.; Prisekin, V. G.

    2016-07-01

    The Philips Digital Photon Counter (DPC) is a silicon photomultiplier combining Geiger-mode avalanche photodiodes (G-APD) and dedicated readout electronics in the same chip. The DPC is a promising photon sensor for future RICH detectors. A known issue of G-APD is its sensitivity to radiation damage. Two DPC sensors were tested using 800 MeV/c protons. An increase of dark counting rate with proton fluence up to 4 ·1011cm-2 has been measured.

  10. Jets and Photons

    NASA Astrophysics Data System (ADS)

    Ellis, Stephen D.; Roy, Tuhin S.; Scholtz, Jakub

    2013-03-01

    This Letter applies the concept of “jets,” as constructed from calorimeter cell four-vectors, to jets composed (primarily) of photons (or leptons). Thus jets become a superset of both traditional objects such as QCD jets, photons, and electrons, and more unconventional objects such as photon jets and electron jets, defined as collinear photons and electrons, respectively. Since standard objects such as single photons become a subset of jets in this approach, standard jet substructure techniques are incorporated into the photon finder toolbox. Using a (reasonably) realistic calorimeter model we demonstrate that, for a single photon identification efficiency of 80% or above, the use of jet substructure techniques reduces the number of QCD jets faking photons by factors of 2.5 to 4. Depending on the topology of the photon jets, the substructure variables reduce the number of photon jets faking single photons by factors of 10 to 103 at a single photon identification efficiency of 80%.

  11. Resonance formation in photon-photon collisions

    SciTech Connect

    Gidal, G.

    1988-08-01

    Recent experimental progress on resonance formation in photon-photon collisions is reviewed with particular emphasis on the pseudoscalar and tensor nonents and on the ..gamma gamma..* production of spin-one resonances. 37 refs., 17 figs., 5 tabs.

  12. Integrated Assessment of Hadley Centre (HadCM2) Climate-Change Impacts on Agricultural Productivity and Irrigation Water Supply in the Conterminous United States. Part II. Regional Agricultural Production in 2030 and 2095.

    SciTech Connect

    Izaurralde, R Cesar C.; Rosenberg, Norman J.; Brown, Robert A.; Thomson, Allison M.

    2003-06-30

    This study used scenarios of the HadCM2 GCM and the EPIC agroecosystem model to evaluate climate change impacts on crop yields and ecosystem processes. Baseline climate data were obtained from records for 1961-1990. The scenario runs for 2025-2034 and 2090-2099 were extracted from a HadCM2 run. EPIC was run on 204 representative farms under current climate and two 10-y periods centered on 2030 and 2095, each at CO2 concentrations of 365 and 560 ppm. Texas, New Mexico, Colorado, Utah, Arizona, and California are projected to experience significant temperature increases by 2030. Slight cooling is expected by 2030 in Alabama, Florida, Maine, Montana, Idaho, and Utah. Larger areas are projected to experience increased warming by 2095. Uniform precipitation increases are expected by 2030 in the NE. These increases are predicted to expand to the eastern half of the country by 2095. EPIC simulated yield increases for the Great Lakes, Corn Belt and Northeast regions. Simulated yields of irrigated corn yields were predicted to increase in almost all regions. Soybean yields could decrease in the Northern and Southern Plains, the Corn Belt, Delta, Appalachian, and Southeast regions and increase in the Lakes and Northeast regions. Simulated wheat yields exhibited upward yield trends under scenarios of climate change. National corn production in 2030 and 2095 could be affected by changes in three major producing regions. In 2030, corn production could increase in the Corn Belt and Lakes regions but decrease in the Northern Plains leading to an overall decrease in national production. National wheat production is expected to increase during both future periods. A proxy indicator was developed to provide a sense of where in the country, and when water would be available to satisfy change in irrigation demand for corn and alfalfa production as these are influenced by the HadCM2 scenarios and CO2-fertilization.

  13. Fully Enzymatic Membraneless Glucose|Oxygen Fuel Cell That Provides 0.275 mA cm(-2) in 5 mM Glucose, Operates in Human Physiological Solutions, and Powers Transmission of Sensing Data.

    PubMed

    Ó Conghaile, Peter; Falk, Magnus; MacAodha, Domhnall; Yakovleva, Maria E; Gonaus, Christoph; Peterbauer, Clemens K; Gorton, Lo; Shleev, Sergey; Leech, Dónal

    2016-02-16

    Coimmobilization of pyranose dehydrogenase as an enzyme catalyst, osmium redox polymers [Os(4,4'-dimethoxy-2,2'-bipyridine)2(poly(vinylimidazole))10Cl](+) or [Os(4,4'-dimethyl-2,2'-bipyridine)2(poly(vinylimidazole))10Cl](+) as mediators, and carbon nanotube conductive scaffolds in films on graphite electrodes provides enzyme electrodes for glucose oxidation. The recombinant enzyme and a deglycosylated form, both expressed in Pichia pastoris, are investigated and compared as biocatalysts for glucose oxidation using flow injection amperometry and voltammetry. In the presence of 5 mM glucose in phosphate-buffered saline (PBS) (50 mM phosphate buffer solution, pH 7.4, with 150 mM NaCl), higher glucose oxidation current densities, 0.41 mA cm(-2), are obtained from enzyme electrodes containing the deglycosylated form of the enzyme. The optimized glucose-oxidizing anode, prepared using deglycosylated enzyme coimmobilized with [Os(4,4'-dimethyl-2,2'-bipyridine)2(poly(vinylimidazole))10Cl](+) and carbon nanotubes, was coupled with an oxygen-reducing bilirubin oxidase on gold nanoparticle dispersed on gold electrode as a biocathode to provide a membraneless fully enzymatic fuel cell. A maximum power density of 275 μW cm(-2) is obtained in 5 mM glucose in PBS, the highest to date under these conditions, providing sufficient power to enable wireless transmission of a signal to a data logger. When tested in whole human blood and unstimulated human saliva maximum power densities of 73 and 6 μW cm(-2) are obtained for the same fuel cell configuration, respectively. PMID:26750758

  14. Direct total cross section measurement of the {sup 16}O({alpha}, {gamma}){sup 20}Ne reaction at E{sub c.m.}=2.26 MeV

    SciTech Connect

    Hager, U.; Greife, U.; Brown, J. R.; Buchmann, L.; Fallis, J.; Hutcheon, D.; Ottewell, D.; Ruiz, C.; Sjue, S.; Carmona-Gallardo, M.; Erikson, L.; Vockenhuber, C.

    2011-08-15

    In stellar helium burning, {sup 16}O represents the endpoint of the helium-burning sequence due to the low rate of {sup 16}O({alpha},{gamma}){sup 20}Ne. We present a new direct measurement of the total capture reaction rate of {sup 16}O({alpha},{gamma}){sup 20}Ne at E{sub c.m.}=2.26 MeV employing the DRAGON recoil separator. For the first time, the total S factor and its contributing direct capture transitions could be determined in one experiment.

  15. An ambipolar organic field-effect transistor based on an AIE-active single crystal with a high mobility level of 2.0 cm(2) V(-1) s(-1).

    PubMed

    Deng, Jian; Xu, Yuanxiang; Liu, Liqun; Feng, Cunfang; Tang, Jia; Gao, Yu; Wang, Yan; Yang, Bing; Lu, Ping; Yang, Wensheng; Ma, Yuguang

    2016-02-01

    Organic field-effect transistors (OFETs) based on an aggregation-induced emission (AIE) material were fabricated using a calcium-gold asymmetric electrode system. The devices showed very high and balanced mobility, reaching 2.50 and 2.10 cm(2) V(-1) s(-1), respectively, for electron and hole. Strong green electroluminescence from the single-crystal side edge was observed from all the devices. This work demonstrates that AIE active materials could not only achieve high luminescence, but also be used in light emitting transistors and achieve very high mobility. PMID:26730680

  16. A Search for Point Sources of EeV Photons

    NASA Astrophysics Data System (ADS)

    Aab, A.; Abreu, P.; Aglietta, M.; Ahlers, M.; Ahn, E. J.; Samarai, I. Al; Albuquerque, I. F. M.; Allekotte, I.; Allen, J.; Allison, P.; Almela, A.; Alvarez Castillo, J.; Alvarez-Muñiz, J.; Alves Batista, R.; Ambrosio, M.; Aminaei, A.; Anchordoqui, L.; Andringa, S.; Aramo, C.; Arqueros, F.; Asorey, H.; Assis, P.; Aublin, J.; Ave, M.; Avenier, M.; Avila, G.; Badescu, A. M.; Barber, K. B.; Bäuml, J.; Baus, C.; Beatty, J. J.; Becker, K. H.; Bellido, J. A.; Berat, C.; Bertou, X.; Biermann, P. L.; Billoir, P.; Blanco, F.; Blanco, M.; Bleve, C.; Blümer, H.; Boháčová, M.; Boncioli, D.; Bonifazi, C.; Bonino, R.; Borodai, N.; Brack, J.; Brancus, I.; Brogueira, P.; Brown, W. C.; Buchholz, P.; Bueno, A.; Buscemi, M.; Caballero-Mora, K. S.; Caccianiga, B.; Caccianiga, L.; Candusso, M.; Caramete, L.; Caruso, R.; Castellina, A.; Cataldi, G.; Cazon, L.; Cester, R.; Chavez, A. G.; Cheng, S. H.; Chiavassa, A.; Chinellato, J. A.; Chudoba, J.; Cilmo, M.; Clay, R. W.; Cocciolo, G.; Colalillo, R.; Collica, L.; Coluccia, M. R.; Conceição, R.; Contreras, F.; Cooper, M. J.; Coutu, S.; Covault, C. E.; Criss, A.; Cronin, J.; Curutiu, A.; Dallier, R.; Daniel, B.; Dasso, S.; Daumiller, K.; Dawson, B. R.; de Almeida, R. M.; De Domenico, M.; de Jong, S. J.; de Mello Neto, J. R. T.; De Mitri, I.; de Oliveira, J.; de Souza, V.; del Peral, L.; Deligny, O.; Dembinski, H.; Dhital, N.; Di Giulio, C.; Di Matteo, A.; Diaz, J. C.; Díaz Castro, M. L.; Diep, P. N.; Diogo, F.; Dobrigkeit, C.; Docters, W.; D'Olivo, J. C.; Dong, P. N.; Dorofeev, A.; Dorosti Hasankiadeh, Q.; Dova, M. T.; Ebr, J.; Engel, R.; Erdmann, M.; Erfani, M.; Escobar, C. O.; Espadanal, J.; Etchegoyen, A.; Facal San Luis, P.; Falcke, H.; Fang, K.; Farrar, G.; Fauth, A. C.; Fazzini, N.; Ferguson, A. P.; Fernandes, M.; Fick, B.; Figueira, J. M.; Filevich, A.; Filipčič, A.; Fox, B. D.; Fratu, O.; Fröhlich, U.; Fuchs, B.; Fuji, T.; Gaior, R.; García, B.; Garcia Roca, S. T.; Garcia-Gamez, D.; Garcia-Pinto, D.; Garilli, G.; Gascon Bravo, A.; Gate, F.; Gemmeke, H.; Ghia, P. L.; Giaccari, U.; Giammarchi, M.; Giller, M.; Glaser, C.; Glass, H.; Gomez Albarracin, F.; Gómez Berisso, M.; Gómez Vitale, P. F.; Gonçalves, P.; Gonzalez, J. G.; Gookin, B.; Gorgi, A.; Gorham, P.; Gouffon, P.; Grebe, S.; Griffith, N.; Grillo, A. F.; Grubb, T. D.; Guardincerri, Y.; Guarino, F.; Guedes, G. P.; Hansen, P.; Harari, D.; Harrison, T. A.; Harton, J. L.; Haungs, A.; Hebbeker, T.; Heck, D.; Heimann, P.; Herve, A. E.; Hill, G. C.; Hojvat, C.; Hollon, N.; Holt, E.; Homola, P.; Hörandel, J. R.; Horvath, P.; Hrabovský, M.; Huber, D.; Huege, T.; Insolia, A.; Isar, P. G.; Islo, K.; Jandt, I.; Jansen, S.; Jarne, C.; Josebachuili, M.; Kääpä, A.; Kambeitz, O.; Kampert, K. H.; Kasper, P.; Katkov, I.; Kégl, B.; Keilhauer, B.; Keivani, A.; Kemp, E.; Kieckhafer, R. M.; Klages, H. O.; Kleifges, M.; Kleinfeller, J.; Krause, R.; Krohm, N.; Krömer, O.; Kruppke-Hansen, D.; Kuempel, D.; Kunka, N.; La Rosa, G.; LaHurd, D.; Latronico, L.; Lauer, R.; Lauscher, M.; Lautridou, P.; Le Coz, S.; Leão, M. S. A. B.; Lebrun, D.; Lebrun, P.; Leigui de Oliveira, M. A.; Letessier-Selvon, A.; Lhenry-Yvon, I.; Link, K.; López, R.; Lopez Agüera, A.; Louedec, K.; Lozano Bahilo, J.; Lu, L.; Lucero, A.; Ludwig, M.; Lyberis, H.; Maccarone, M. C.; Malacari, M.; Maldera, S.; Maller, J.; Mandat, D.; Mantsch, P.; Mariazzi, A. G.; Marin, V.; Mariş, I. C.; Marsella, G.; Martello, D.; Martin, L.; Martinez, H.; Martínez Bravo, O.; Martraire, D.; Masías Meza, J. J.; Mathes, H. J.; Mathys, S.; Matthews, A. J.; Matthews, J.; Matthiae, G.; Maurel, D.; Maurizio, D.; Mayotte, E.; Mazur, P. O.; Medina, C.; Medina-Tanco, G.; Melissas, M.; Melo, D.; Menichetti, E.; Menshikov, A.; Messina, S.; Meyhandan, R.; Mićanović, S.; Micheletti, M. I.; Middendorf, L.; Minaya, I. A.; Miramonti, L.; Mitrica, B.; Molina-Bueno, L.; Mollerach, S.; Monasor, M.; Monnier Ragaigne, D.; Montanet, F.; Morello, C.; Moreno, J. C.; Mostafá, M.; Moura, C. A.; Muller, M. A.; Müller, G.; Münchmeyer, M.; Mussa, R.; Navarra, G.; Navas, S.; Necesal, P.; Nellen, L.; Nelles, A.; Neuser, J.; Niechciol, M.; Niemietz, L.; Niggemann, T.; Nitz, D.; Nosek, D.; Novotny, V.; Nožka, L.; Ochilo, L.; Olinto, A.; Oliveira, M.; Ortiz, M.; Pacheco, N.; Pakk Selmi-Dei, D.; Palatka, M.; Pallotta, J.; Palmieri, N.; Papenbreer, P.; Parente, G.; Parra, A.; Pastor, S.; Paul, T.; Pech, M.; Peķala, J.; Pelayo, R.; Pepe, I. M.; Perrone, L.; Pesce, R.; Petermann, E.; Peters, C.; Petrera, S.; Petrolini, A.; Petrov, Y.; Piegaia, R.; Pierog, T.; Pieroni, P.; Pimenta, M.; Pirronello, V.; Platino, M.; Plum, M.; Porcelli, A.; Porowski, C.; Privitera, P.; Prouza, M.; Purrello, V.; Quel, E. J.; Querchfeld, S.; Quinn, S.; Rautenberg, J.; Ravel, O.; Ravignani, D.; Revenu, B.; Ridky, J.; Riggi, S.; Risse, M.; Ristori, P.; Rizi, V.; Roberts, J.; Rodrigues de Carvalho, W.; Rodriguez Cabo, I.; Rodriguez Fernandez, G.; Rodriguez Rojo, J.; Rodríguez-Frías, M. D.; Ros, G.; Rosado, J.; Rossler, T.; Roth, M.; Roulet, E.; Rovero, A. C.; Rühle, C.; Saffi, S. J.; Saftoiu, A.; Salamida, F.; Salazar, H.; Salesa Greus, F.; Salina, G.; Sánchez, F.; Sanchez-Lucas, P.; Santo, C. E.; Santos, E.; Santos, E. M.; Sarazin, F.; Sarkar, B.; Sarmento, R.; Sato, R.; Scharf, N.; Scherini, V.; Schieler, H.; Schiffer, P.; Schmidt, A.; Scholten, O.; Schoorlemmer, H.; Schovánek, P.; Schulz, A.; Schulz, J.; Sciutto, S. J.; Segreto, A.; Settimo, M.; Shadkam, A.; Shellard, R. C.; Sidelnik, I.; Sigl, G.; Sima, O.; Śmiałkowski, A.; Šmída, R.; Snow, G. R.; Sommers, P.; Sorokin, J.; Squartini, R.; Srivastava, Y. N.; Stanič, S.; Stapleton, J.; Stasielak, J.; Stephan, M.; Stutz, A.; Suarez, F.; Suomijärvi, T.; Supanitsky, A. D.; Sutherland, M. S.; Swain, J.; Szadkowski, Z.; Szuba, M.; Taborda, O. A.; Tapia, A.; Tartare, M.; Thao, N. T.; Theodoro, V. M.; Tiffenberg, J.; Timmermans, C.; Todero Peixoto, C. J.; Toma, G.; Tomankova, L.; Tomé, B.; Tonachini, A.; Torralba Elipe, G.; Torres Machado, D.; Travnicek, P.; Trovato, E.; Tueros, M.; Ulrich, R.; Unger, M.; Urban, M.; Valdés Galicia, J. F.; Valiño, I.; Valore, L.; van Aar, G.; van den Berg, A. M.; van Velzen, S.; van Vliet, A.; Varela, E.; Vargas Cárdenas, B.; Varner, G.; Vázquez, J. R.; Vázquez, R. A.; Veberič, D.; Verzi, V.; Vicha, J.; Videla, M.; Villaseñor, L.; Vlcek, B.; Vorobiov, S.; Wahlberg, H.; Wainberg, O.; Walz, D.; Watson, A. A.; Weber, M.; Weidenhaupt, K.; Weindl, A.; Werner, F.; Whelan, B. J.; Widom, A.; Wiencke, L.; Wilczyńska, B.; Wilczyński, H.; Will, M.; Williams, C.; Winchen, T.; Wittkowski, D.; Wundheiler, B.; Wykes, S.; Yamamoto, T.; Yapici, T.; Younk, P.; Yuan, G.; Yushkov, A.; Zamorano, B.; Zas, E.; Zavrtanik, D.; Zavrtanik, M.; Zaw, I.; Zepeda, A.; Zhou, J.; Zhu, Y.; Zimbres Silva, M.; Ziolkowski, M.; Auger Collaboration102, The Pierre

    2014-07-01

    Measurements of air showers made using the hybrid technique developed with the fluorescence and surface detectors of the Pierre Auger Observatory allow a sensitive search for point sources of EeV photons anywhere in the exposed sky. A multivariate analysis reduces the background of hadronic cosmic rays. The search is sensitive to a declination band from -85° to +20°, in an energy range from 1017.3 eV to 1018.5 eV. No photon point source has been detected. An upper limit on the photon flux has been derived for every direction. The mean value of the energy flux limit that results from this, assuming a photon spectral index of -2, is 0.06 eV cm-2 s-1, and no celestial direction exceeds 0.25 eV cm-2 s-1. These upper limits constrain scenarios in which EeV cosmic ray protons are emitted by non-transient sources in the Galaxy.

  17. Low level laser therapy (AlGaInP) applied at 5J/cm2 reduces the proliferation of Staphylococcus aureus MRSA in infected wounds and intact skin of rats*

    PubMed Central

    Silva, Daniela Conceição Gomes Gonçalves e; Plapler, Helio; da Costa, Mateus Matiuzzi; Silva, Silvio Romero Gonçalves e; de Sá, Maria da Conceição Aquino; Silva, Benedito Sávio Lima e

    2013-01-01

    BACKGROUND Laser therapy is a low cost, non-invasive procedure with good healing results. Doubts exist as to whether laser therapy action on microorganisms can justify research aimed at investigating its possible effects on bacteria-infected wounds. OBJECTIVE To assess the effect of low intensity laser on the rate of bacterial contamination in infected wounds in the skin of rats. METHODS An experimental study using 56 male Wistar rats. The animals were randomly divided into eight groups of seven each. Those in the "infected" groups were infected by Staphylococcus aureus MRSA in the dorsal region. Red laser diode (AlGaInP) 658nm, 5J/cm2 was used to treat the animals in the "treated" groups in scan for 3 consecutive days. Samples were drawn before inoculating bacteria and following laser treatment. For statistical analysis we used the nonparametric Wilcoxon (paired data) method with a significance level of p <0.05. RESULTS The statistical analysis of median values showed that the groups submitted to laser treatment had low bacterial proliferation. CONCLUSION The laser (AlGaInP), with a dose of 5J/cm2 in both intact skin and in wounds of rats infected with Staphylococcus aureus MRSA, is shown to reduce bacterial proliferation. PMID:23539003

  18. Photon-sparse microscopy: Trans-wavelength ghost imaging

    NASA Astrophysics Data System (ADS)

    Aspden, Reuben S.; Gemmell, Nathan R.; Morris, Peter A.; Tasca, Daniel S.; Mertens, Lena; Tanner, Michael G.; Kirkwood, Robert A.; Ruggeri, Alessandro; Tosi, Alberto; Boyd, Robert W.; Buller, Gerald S.; Hadfield, Robert H.; Padgett, Miles J.

    2016-05-01

    Ghost imaging systems use down-conversion sources that produce twin output beams of position-correlated photons to produce an image of an object using photons that did not interact with the object. One of these beams illuminates the object and is detected by a single pixel detector while the image information is recovered from the second, spatially correlated, beam. We utilize this technique to obtain images of objects probed with 1.5μm photons whilst developing the image using a highly efficient, low-noise, photon-counting camera detecting the correlated photons at 460nm. The efficient transfer of the image information from infrared illumination to visible detection wavelengths and the ability to count single-photons allows the acquisition of an image while illuminating the object with an optical power density of only 100 pJ cm-2 s-1. We apply image reconstruction techniques based on compressive sensing to reconstruct our images from data sets containing far fewer photons than conventionally required. This wavelength-transforming ghost imaging technique has potential for the imaging of light-sensitive specimens or where covert operation is desired.

  19. RR photons

    NASA Astrophysics Data System (ADS)

    Cámara, Pablo G.; Ibáñez, Luis E.; Marchesano, Fernando

    2011-09-01

    Type II string compactifications to 4d generically contain massless Ramond-Ramond U(1) gauge symmetries. However there is no massless matter charged under these U(1)'s, which makes a priori difficult to measure any physical consequences of their existence. There is however a window of opportunity if these RR U(1)'s mix with the hypercharge U(1) Y (hence with the photon). In this paper we study in detail different avenues by which U(1) RR bosons may mix with D-brane U(1)'s. We concentrate on Type IIA orientifolds and their M-theory lift, and provide geometric criteria for the existence of such mixing, which may occur either via standard kinetic mixing or via the mass terms induced by Stückelberg couplings. The latter case is particularly interesting, and appears whenever D-branes wrap torsional p-cycles in the compactification manifold. We also show that in the presence of torsional cycles discrete gauge symmetries and Aharanov-Bohm strings and particles appear in the 4d effective action, and that type IIA Stückelberg couplings can be understood in terms of torsional (co)homology in M-theory. We provide examples of Type IIA Calabi-Yau orientifolds in which the required torsional cycles exist and kinetic mixing induced by mass mixing is present. We discuss some phenomenological consequences of our findings. In particular, we find that mass mixing may induce corrections relevant for hypercharge gauge coupling unification in F-theory SU(5) GUT's.

  20. Photon-Photon Collisions -- Past and Future

    SciTech Connect

    Brodsky, Stanley J.; /SLAC

    2005-12-02

    I give a brief review of the history of photon-photon physics and a survey of its potential at future electron-positron colliders. Exclusive hadron production processes in photon-photon and electron-photon collisions provide important tests of QCD at the amplitude level, particularly as measures of hadron distribution amplitudes. There are also important high energy {gamma}{gamma} and e{gamma} tests of quantum chromodynamics, including the production of jets in photon-photon collisions, deeply virtual Compton scattering on a photon target, and leading-twist single-spin asymmetries for a photon polarized normal to a production plane. Since photons couple directly to all fundamental fields carrying the electromagnetic current including leptons, quarks, W's and supersymmetric particles, high energy {gamma}{gamma} collisions will provide a comprehensive laboratory for Higgs production and exploring virtually every aspect of the Standard Model and its extensions. High energy back-scattered laser beams will thus greatly extend the range of physics of the International Linear Collider.

  1. A cavity experiment to search for hidden sector photons

    NASA Astrophysics Data System (ADS)

    Jaeckel, Joerg; Ringwald, Andreas

    2008-01-01

    We propose a cavity experiment to search for low mass extra U(1) gauge bosons with gauge-kinetic mixing with the ordinary photon, so-called paraphotons. The setup consists of two microwave cavities shielded from each other. In one cavity, paraphotons are produced via photon-paraphoton oscillations. The second, resonant, cavity is then driven by the paraphotons that permeate the shielding and reconvert into photons. This setup resembles the classic "light shining through a wall" setup. However, the high quality factors achievable for microwave cavities and the good sensitivity of microwave detectors allow for a projected sensitivity for photon-paraphoton mixing of the order of χ ∼10-12-10-8, for paraphotons with masses in the μeV to meV range-exceeding the current laboratory and astrophysics-based limits by several orders of magnitude. Therefore, this experiment bears significant discovery potential for hidden sector physics.

  2. InGaAs/InAlAs single photon avalanche diode for 1550 nm photons.

    PubMed

    Meng, Xiao; Xie, Shiyu; Zhou, Xinxin; Calandri, Niccolò; Sanzaro, Mirko; Tosi, Alberto; Tan, Chee Hing; Ng, Jo Shien

    2016-03-01

    A single photon avalanche diode (SPAD) with an InGaAs absorption region, and an InAlAs avalanche region was designed and demonstrated to detect 1550 nm wavelength photons. The characterization included leakage current, dark count rate and single photon detection efficiency as functions of temperature from 210 to 294 K. The SPAD exhibited good temperature stability, with breakdown voltage dependence of approximately 45 mV K(-1). Operating at 210 K and in a gated mode, the SPAD achieved a photon detection probability of 26% at 1550 nm with a dark count rate of 1 × 10(8) Hz. The time response of the SPAD showed decreasing timing jitter (full width at half maximum) with increasing overbias voltage, with 70 ps being the smallest timing jitter measured.

  3. InGaAs/InAlAs single photon avalanche diode for 1550 nm photons.

    PubMed

    Meng, Xiao; Xie, Shiyu; Zhou, Xinxin; Calandri, Niccolò; Sanzaro, Mirko; Tosi, Alberto; Tan, Chee Hing; Ng, Jo Shien

    2016-03-01

    A single photon avalanche diode (SPAD) with an InGaAs absorption region, and an InAlAs avalanche region was designed and demonstrated to detect 1550 nm wavelength photons. The characterization included leakage current, dark count rate and single photon detection efficiency as functions of temperature from 210 to 294 K. The SPAD exhibited good temperature stability, with breakdown voltage dependence of approximately 45 mV K(-1). Operating at 210 K and in a gated mode, the SPAD achieved a photon detection probability of 26% at 1550 nm with a dark count rate of 1 × 10(8) Hz. The time response of the SPAD showed decreasing timing jitter (full width at half maximum) with increasing overbias voltage, with 70 ps being the smallest timing jitter measured. PMID:27069647

  4. Nuclear photonics

    SciTech Connect

    Habs, D.; Guenther, M. M.; Jentschel, M.; Thirolf, P. G.

    2012-07-09

    With the planned new {gamma}-beam facilities like MEGa-ray at LLNL (USA) or ELI-NP at Bucharest (Romania) with 10{sup 13}{gamma}/s and a band width of {Delta}E{gamma}/E{gamma} Almost-Equal-To 10{sup -3}, a new era of {gamma} beams with energies up to 20MeV comes into operation, compared to the present world-leading HI{gamma}S facility at Duke University (USA) with 10{sup 8}{gamma}/s and {Delta}E{gamma}/E{gamma} Almost-Equal-To 3 Dot-Operator 10{sup -2}. In the long run even a seeded quantum FEL for {gamma} beams may become possible, with much higher brilliance and spectral flux. At the same time new exciting possibilities open up for focused {gamma} beams. Here we describe a new experiment at the {gamma} beam of the ILL reactor (Grenoble, France), where we observed for the first time that the index of refraction for {gamma} beams is determined by virtual pair creation. Using a combination of refractive and reflective optics, efficient monochromators for {gamma} beams are being developed. Thus, we have to optimize the total system: the {gamma}-beam facility, the {gamma}-beam optics and {gamma} detectors. We can trade {gamma} intensity for band width, going down to {Delta}E{gamma}/E{gamma} Almost-Equal-To 10{sup -6} and address individual nuclear levels. The term 'nuclear photonics' stresses the importance of nuclear applications. We can address with {gamma}-beams individual nuclear isotopes and not just elements like with X-ray beams. Compared to X rays, {gamma} beams can penetrate much deeper into big samples like radioactive waste barrels, motors or batteries. We can perform tomography and microscopy studies by focusing down to {mu}m resolution using Nuclear Resonance Fluorescence (NRF) for detection with eV resolution and high spatial resolution at the same time. We discuss the dominating M1 and E1 excitations like the scissors mode, two-phonon quadrupole octupole excitations, pygmy dipole excitations or giant dipole excitations under the new facet of

  5. Nuclear photonics

    NASA Astrophysics Data System (ADS)

    Habs, D.; Günther, M. M.; Jentschel, M.; Thirolf, P. G.

    2012-07-01

    With the planned new γ-beam facilities like MEGa-ray at LLNL (USA) or ELI-NP at Bucharest (Romania) with 1013 γ/s and a band width of ΔEγ/Eγ≈10-3, a new era of γ beams with energies up to 20MeV comes into operation, compared to the present world-leading HIγS facility at Duke University (USA) with 108 γ/s and ΔEγ/Eγ≈3ṡ10-2. In the long run even a seeded quantum FEL for γ beams may become possible, with much higher brilliance and spectral flux. At the same time new exciting possibilities open up for focused γ beams. Here we describe a new experiment at the γ beam of the ILL reactor (Grenoble, France), where we observed for the first time that the index of refraction for γ beams is determined by virtual pair creation. Using a combination of refractive and reflective optics, efficient monochromators for γ beams are being developed. Thus, we have to optimize the total system: the γ-beam facility, the γ-beam optics and γ detectors. We can trade γ intensity for band width, going down to ΔEγ/Eγ≈10-6 and address individual nuclear levels. The term "nuclear photonics" stresses the importance of nuclear applications. We can address with γ-beams individual nuclear isotopes and not just elements like with X-ray beams. Compared to X rays, γ beams can penetrate much deeper into big samples like radioactive waste barrels, motors or batteries. We can perform tomography and microscopy studies by focusing down to μm resolution using Nuclear Resonance Fluorescence (NRF) for detection with eV resolution and high spatial resolution at the same time. We discuss the dominating M1 and E1 excitations like the scissors mode, two-phonon quadrupole octupole excitations, pygmy dipole excitations or giant dipole excitations under the new facet of applications. We find many new applications in biomedicine, green energy, radioactive waste management or homeland security. Also more brilliant secondary beams of neutrons and positrons can be produced.

  6. The origin of seed photons for Comptonization in the black hole binary Swift J1753.5-0127

    NASA Astrophysics Data System (ADS)

    Kajava, J. J. E.; Veledina, A.; Tsygankov, S.; Neustroev, V.

    2016-06-01

    Aims: The black hole binary Swift J1753.5-0127 is providing a unique data set to study accretion flows. Various investigations of this system and of other black holes have not, however, led to an agreement on the accretion flow geometry or on the seed photon source for Comptonization during different stages of X-ray outbursts. We place constraints on these accretion flow properties by studying long-term spectral variations of this source. Methods: We performed phenomenological and self-consistent broad band spectral modeling of Swift J1753.5-0127 using quasi-simultaneous archived data from INTEGRAL/ISGRI, Swift/UVOT/XRT/BAT, RXTE/PCA/HEXTE, and MAXI/GSC instruments. Results: We identify a critical flux limit, F ~ 1.5 × 10-8 erg cm-2 s-1, and show that the spectral properties of Swift J1753.5-0127 are markedly different above and below this value. Above the limit, during the outburst peak, the hot medium seems to intercept roughly 50 percent of the disk emission. Below it, in the outburst tail, the contribution of the disk photons reduces significantly and the entire spectrum from the optical to X-rays can be produced by a synchrotron-self-Compton mechanism. The long-term variations in the hard X-ray spectra are caused by erratic changes of the electron temperatures in the hot medium. Thermal Comptonization models indicate unreasonably low hot medium optical depths during the short incursions into the soft state after 2010, suggesting that non-thermal electrons produce the Comptonized tail in this state. The soft X-ray excess, likely produced by the accretion disk, shows peculiarly stable temperatures for over an order of magnitude changes in flux. Conclusions: The long-term spectral trends of Swift J1753.5-0127 are likely set by variations of the truncation radius and a formation of a hot, quasi-spherical inner flow in the vicinity of the black hole. In the late outburst stages, at fluxes below the critical limit, the source of seed photons for Comptonization is

  7. Determination of the type of stacking faults in single-crystal high-purity diamond with a low dislocation density of <50 cm-2 by synchrotron X-ray topography

    NASA Astrophysics Data System (ADS)

    Masuya, Satoshi; Hanada, Kenji; Uematsu, Takumi; Moribayashi, Tomoya; Sumiya, Hitoshi; Kasu, Makoto

    2016-04-01

    The properties of stacking faults in a single-crystal high-purity diamond with a very low dislocation density of <50 cm-2 and a very low impurity concentration of <0.1 ppm were investigated by synchrotron X-ray topography. We found stacking faults on the {111} plane and determined the fault vector f of the stacking faults to be \\textbf{f} = a/3< 111> on the basis of the f · g extinction criteria. Furthermore, we have found that the partial dislocations are of the Shockley type on the basis of the b · g extinction criteria. Consequently, we concluded that the stacking faults are of the Shockley type and formed because of the decomposition of dislocations with \\textbf{b} = a/2< 1\\bar{1}0> into dislocations with \\textbf{b} = a/6< 2\\bar{1}1> and a/6< 1\\bar{2}\\bar{1}> .

  8. Repeated high-dose (5 × 10(8) TCID50) toxicity study of a third generation smallpox vaccine (IMVAMUNE) in New Zealand white rabbits.

    PubMed

    Tree, Julia A; Hall, Graham; Rees, Peter; Vipond, Julia; Funnell, Simon G P; Roberts, Allen D

    2016-07-01

    Concern over the release of variola virus as an agent of bioterrorism remains high and a rapid vaccination regimen is desirable for use in the event of a confirmed release of virus. A single, high-dose (5×10(8) TCID50) of Bavarian Nordic's IMVAMUNE was tested in a Phase-II clinical trial, in humans, as a substitute for the standard (1×10(8) TCID50), using a 2-dose, 28-days apart regimen. Prior to this clinical trial taking place a Good Laboratory Practice, repeated high-dose, toxicology study was performed using IMVAMUNE, in New Zealand white rabbits and the results are reported here. Male and female rabbits were dosed twice, subcutaneously, with 5×10(8) TCID50 of IMVAMUNE (test) or saline (control), 7-days apart. The clinical condition, body-weight, food consumption, haematology, blood chemistry, immunogenicity, organ-weight, and macroscopic and microscopic pathology were investigated. Haematological investigations indicated changes within the white blood cell profile that were attributed to treatment with IMVAMUNE; these comprised slight increases in neutrophil and monocyte numbers, on study days 1-3 and a marginal increase in lymphocyte numbers on day 10. Macroscopic pathology revealed reddening at the sites of administration and thickened skin in IMVAMUNE, treated animals. After the second dose of IMVAMUNE 9/10 rabbits seroconverted, as detected by antibody ELISA on day 10, by day 21, 10/10 rabbits seroconverted. Treatment-related changes were not detected in other parameters. In conclusion, the subcutaneous injection of 2 high-doses of IMVAMUNE, to rabbits, was well tolerated producing only minor changes at the site of administration. Vaccinia-specific antibodies were raised in IMVAMUNE-vaccinated rabbits only.

  9. Repeated high-dose (5 × 10(8) TCID50) toxicity study of a third generation smallpox vaccine (IMVAMUNE) in New Zealand white rabbits.

    PubMed

    Tree, Julia A; Hall, Graham; Rees, Peter; Vipond, Julia; Funnell, Simon G P; Roberts, Allen D

    2016-07-01

    Concern over the release of variola virus as an agent of bioterrorism remains high and a rapid vaccination regimen is desirable for use in the event of a confirmed release of virus. A single, high-dose (5×10(8) TCID50) of Bavarian Nordic's IMVAMUNE was tested in a Phase-II clinical trial, in humans, as a substitute for the standard (1×10(8) TCID50), using a 2-dose, 28-days apart regimen. Prior to this clinical trial taking place a Good Laboratory Practice, repeated high-dose, toxicology study was performed using IMVAMUNE, in New Zealand white rabbits and the results are reported here. Male and female rabbits were dosed twice, subcutaneously, with 5×10(8) TCID50 of IMVAMUNE (test) or saline (control), 7-days apart. The clinical condition, body-weight, food consumption, haematology, blood chemistry, immunogenicity, organ-weight, and macroscopic and microscopic pathology were investigated. Haematological investigations indicated changes within the white blood cell profile that were attributed to treatment with IMVAMUNE; these comprised slight increases in neutrophil and monocyte numbers, on study days 1-3 and a marginal increase in lymphocyte numbers on day 10. Macroscopic pathology revealed reddening at the sites of administration and thickened skin in IMVAMUNE, treated animals. After the second dose of IMVAMUNE 9/10 rabbits seroconverted, as detected by antibody ELISA on day 10, by day 21, 10/10 rabbits seroconverted. Treatment-related changes were not detected in other parameters. In conclusion, the subcutaneous injection of 2 high-doses of IMVAMUNE, to rabbits, was well tolerated producing only minor changes at the site of administration. Vaccinia-specific antibodies were raised in IMVAMUNE-vaccinated rabbits only. PMID:26836234

  10. Controllable photon source

    NASA Astrophysics Data System (ADS)

    Oszetzky, Dániel; Nagy, Attila; Czitrovszky, Aladár

    2006-10-01

    We have developed our pervious experimental setup using correlated photon pairs (to the calibration of photo detectors) to realize a controllable photon source. For the generation of such photon pairs we use the non-linear process of parametric down conversion. When a photon of the pump beam is incident to a nonlinear crystal with phase matching condition, a pair of photons (signal and idler) is created at the same time with certain probability. We detect the photons in the signal beam with a single photon counting module (SPCM), while delaying those in the idler beam. Recently we have developed a fast electronic unit to control an optical shutter (a Pockels cell) placed to the optical output of the idler beam. When we detect a signal photon with the controlling electronic unit we are also able to open or close the fast optical shutter. Thus we can control which idler photons can propagate through the Pockels cell. So with this photon source we are able to program the number of photons in a certain time window. This controllable photon source that is able to generate a known number of photons with specified wavelength, direction, and polarization could be useful for applications in high-accuracy optical characterisation of photometric devices at the ultra-low intensities. This light source can also serve as a standard in testing of optical image intensifiers, night vision devices, and in the accurate measurement of spectral distribution of transmission and absorption in optical materials.

  11. Photonic crystal light source

    DOEpatents

    Fleming, James G.; Lin, Shawn-Yu; Bur, James A.

    2004-07-27

    A light source is provided by a photonic crystal having an enhanced photonic density-of-states over a band of frequencies and wherein at least one of the dielectric materials of the photonic crystal has a complex dielectric constant, thereby producing enhanced light emission at the band of frequencies when the photonic crystal is heated. The dielectric material can be a metal, such as tungsten. The spectral properties of the light source can be easily tuned by modification of the photonic crystal structure and materials. The photonic crystal light source can be heated electrically or other heating means. The light source can further include additional photonic crystals that exhibit enhanced light emission at a different band of frequencies to provide for color mixing. The photonic crystal light source may have applications in optical telecommunications, information displays, energy conversion, sensors, and other optical applications.

  12. Photonic Design for Photovoltaics

    SciTech Connect

    Kosten, E.; Callahan, D.; Horowitz, K.; Pala, R.; Atwater, H.

    2014-08-28

    We describe photonic design approaches for silicon photovoltaics including i) trapezoidal broadband light trapping structures ii) broadband light trapping with photonic crystal superlattices iii) III-V/Si nanowire arrays designed for broadband light trapping.

  13. Optimized anisotropic magnetoelectric response of Fe61.6Co16.4Si10.8B11.2/PVDF/Fe61.6Co16.4Si10.8B11.2 laminates for AC/DC magnetic field sensing

    NASA Astrophysics Data System (ADS)

    Reis, S.; Silva, M. P.; Castro, N.; Correia, V.; Gutierrez, J.; Lasheras, A.; Lanceros-Mendez, S.; Martins, P.

    2016-05-01

    The anisotropic magnetoelectric (ME) effect on a Fe61.6Co16.4Si10.8B11.2/PVDF Fe61.6Co16.4Si10.8B11.2 laminate composite has been used for the development of a magnetic field sensor able to detect both the magnitude and direction of AC and DC magnetic fields. The accuracy (99% for both AC and DC sensors), linearity (92% for the DC sensor and 99% for the AC sensor) and reproducibility (99% for both sensors) indicate the suitability of the sensor for applications. Furthermore, the sensitivity of the Fe61.6Co16.4Si10.8B11.2/PVDF/Fe61.6Co16.4Si10.8B11.2 anisotropic magnetic sensor—15 and 1400 mV Oe-1 for the DC and AC fields, respectively—are the highest reported in the literature for polymer-based ME materials. Such features, combined with its flexibility, versatility, light weight, low cost and low-temperature fabrication, lead to the suitability of the developed sensor for use in magnetic sensor applications.

  14. Phase Equilibrium Study of ZnO-"FeO"-SiO2 System at Fixed Po2 10-8 atm

    NASA Astrophysics Data System (ADS)

    Liu, Hongquan; Cui, Zhixiang; Chen, Mao; Zhao, Baojun

    2016-02-01

    Experimental studies of phase equilibria and liquidus temperatures have been carried out in the systems "FeO"-SiO2 and ZnO-"FeO"-SiO2 at Po2 10-8 atm. Research techniques have been developed to enable the ZnO-containing system to be investigated under reducing conditions controlled by CO-CO2 gas mixture. The experimental approach includes master slag preparation, high-temperature equilibration, quench, and electron probe X-ray microanalysis (EPMA). Phase compositions in the quenched samples were measured by EPMA and used for construction of phase diagram. It was found that the isotherms of the system ZnO-"FeO"-SiO2 at Po2 10-8 atm are significantly different from those in equilibrium with metallic iron and those predicted by FactSage. The presence of ZnO in copper smelting slag significantly increases the liquidus temperature in spinel primary phase field. Partitioning of ZnO in liquid and spinel is also discussed in this paper.

  15. Replacement of olivine by serpentine in the Queen Alexandra Range 93005 carbonaceous chondrite (CM2): Reactant-product compositional relations, and isovolumetric constraints on reaction stoichiometry and elemental mobility during aqueous alteration

    NASA Astrophysics Data System (ADS)

    Velbel, Michael A.; Tonui, Eric K.; Zolensky, Michael E.

    2015-01-01

    Isovolumetric replacement of euhedral and anhedral olivine by serpentine produced both centripetal and meshwork textures in the CM2 chondrites ALH 81002 and Nogoya. The compositions of these textural varieties of serpentine are uniform within narrow limits within each previously studied meteorite, independent of the composition of olivine being replaced, and different between the two meteorites. In QUE 93005 (CM2), coarse olivines of widely varying compositions (Fo<76-99) are replaced in a texturally similar manner by compositionally uniform serpentine (Mg0.73±0.05Fe0.27±0.05)3Si2O5(OH)4. The narrow compositional range of serpentine replacing coarse olivine indicates that the aqueous solution from which the serpentine formed was compositionally uniform on scales at least as large as the meteorite (∼2.5 cm in longest dimension). Isovolumetric textures and compositional observations constrain elemental redistribution from coarse olivine to serpentine and to surrounding phases during serpentinization. Regardless of olivine's composition, isovolumetric replacement of coarse olivines by serpentine of the observed composition released more Mg and Si from olivine than was required to form the serpentine. Excess Mg and Si released by olivine destruction and not retained in serpentine were exported from the replaced volume. Olivines with different Fa/Fo proportions contributed different amounts of Fe and Mg to the serpentine. Ferroan olivines released more Fe than required to form the serpentines replacing them, so some of the Fe released from ferroan olivine was exported from the replaced volumes. Forsteritic olivines released less Fe than required to form the serpentines replacing them, so some Fe was imported into the replaced volumes augmenting the small amount of Fe released from forsteritic olivine. In QUE 93005 Fo83.8 is the threshold composition between Fe-exporting and Fe-importing behavior in individual olivine-serpentine pairs, which released exactly the

  16. Ionization of Au{sup 78+} and electron capture by Au{sup 79+} at 10.8 GeV/nucleon

    SciTech Connect

    Claytor, N.; Belkacem, A.; Dinneen, T.; Feinberg, B.; Gould, H.

    1997-02-01

    We have measured the cross sections for ionizating one-electron Au{sup 78+} and the total cross sections for electron capture by bare Au{sup 79+} at 10.8 GeV/nucleon in C, Al, Cu, Ag, and Au targets. We made the measurement by magnetically separating the charge states and measuring the fraction of Au{sup 78+} as a function of target thickness for each element. In contrast to the results reported by Westphal and He [Phys. Rev. Lett. {bold 71}, 1160 (1993)], our ionization measurements agree with the calculation of Anholt and Becker [Phys. Rev. A {bold 36}, 4628 (1987)]. Our capture cross-section measurements are in agreement with theory for those targets where radiative electron capture is the dominant capture process. {copyright} {ital 1997} {ital The American Physical Society}

  17. Enhanced therapeutic anti-inflammatory effect of betamethasone upon topical administration with low frequency, low intensity (20 kHz, 100 mW/cm2) ultrasound exposure on carrageenan-induced arthritis in mice model

    PubMed Central

    Cohen, Gadi; Natsheh, Hiba; Sunny, Youhan; Bawiec, Christopher R.; Touitou, Elka; Lerman, Melissa A.; Lazarovici, Philip; Lewin, Peter A.

    2015-01-01

    The purpose of this work was to investigate whether low frequency, low intensity (LFLI, 20 kHz, <100 mW/cm2, spatial-peak, temporal-peak) ultrasound (US), delivered by a light-weight (<100g), tether-free, fully wearable, battery powered applicator is capable of reducing inflammation in a mouse model of Rheumatoid Arthritis (RA). The therapeutic, acute, anti-inflammatory effect was estimated by the relative swelling induced in mice hind limb paws. In an independent, indirect approach, the inflammation was bio-imaged by measuring glycolytic activity with near infrared labeled 2-deoxy-glucose (2DG). The outcome of the experiments indicated that the combination of US exposure with topical application of 0.1% w/w betamethasone gel, exhibited statistically significant (p<0.05) enhanced anti-inflammatory properties in comparison with the drug or US treatment alone. The present study underscores the potential benefits of LFLI US assisted drug delivery. However, the proof of concept presented indicates the need for additional experiments to systematically evaluate and optimize the potential of, and the conditions for, safe, LFLI ultrasound promoted non-invasive drug delivery. PMID:26003010

  18. Generation of high-photon flux-coherent soft x-ray radiation with few-cycle pulses.

    PubMed

    Demmler, Stefan; Rothhardt, Jan; Hädrich, Steffen; Krebs, Manuel; Hage, Arvid; Limpert, Jens; Tünnermann, Andreas

    2013-12-01

    We present a tabletop source of coherent soft x-ray radiation with high-photon flux. Two-cycle pulses delivered by a fiber-laser-pumped optical parametric chirped-pulse amplifier operating at 180 kHz repetition rate are upconverted via high harmonic generation in neon to photon energies beyond 200 eV. A maximum photon flux of 1.3·10(8) photons/s is achieved within a 1% bandwidth at 125 eV photon energy. This corresponds to a conversion efficiency of ~10(-9), which can be reached due to a gas jet simultaneously providing a high target density and phase matching. Further scaling potential toward higher photon flux as well as higher photon energies are discussed.

  19. Generation of high-photon flux-coherent soft x-ray radiation with few-cycle pulses.

    PubMed

    Demmler, Stefan; Rothhardt, Jan; Hädrich, Steffen; Krebs, Manuel; Hage, Arvid; Limpert, Jens; Tünnermann, Andreas

    2013-12-01

    We present a tabletop source of coherent soft x-ray radiation with high-photon flux. Two-cycle pulses delivered by a fiber-laser-pumped optical parametric chirped-pulse amplifier operating at 180 kHz repetition rate are upconverted via high harmonic generation in neon to photon energies beyond 200 eV. A maximum photon flux of 1.3·10(8) photons/s is achieved within a 1% bandwidth at 125 eV photon energy. This corresponds to a conversion efficiency of ~10(-9), which can be reached due to a gas jet simultaneously providing a high target density and phase matching. Further scaling potential toward higher photon flux as well as higher photon energies are discussed. PMID:24281507

  20. Single-photon sources

    NASA Astrophysics Data System (ADS)

    Lounis, Brahim; Orrit, Michel

    2005-05-01

    The concept of the photon, central to Einstein's explanation of the photoelectric effect, is exactly 100 years old. Yet, while photons have been detected individually for more than 50 years, devices producing individual photons on demand have only appeared in the last few years. New concepts for single-photon sources, or 'photon guns', have originated from recent progress in the optical detection, characterization and manipulation of single quantum objects. Single emitters usually deliver photons one at a time. This so-called antibunching of emitted photons can arise from various mechanisms, but ensures that the probability of obtaining two or more photons at the same time remains negligible. We briefly recall basic concepts in quantum optics and discuss potential applications of single-photon states to optical processing of quantum information: cryptography, computing and communication. A photon gun's properties are significantly improved by coupling it to a resonant cavity mode, either in the Purcell or strong-coupling regimes. We briefly recall early production of single photons with atomic beams, and the operation principles of macroscopic parametric sources, which are used in an overwhelming majority of quantum-optical experiments. We then review the photophysical and spectroscopic properties and compare the advantages and weaknesses of various single nanometre-scale objects used as single-photon sources: atoms or ions in the gas phase and, in condensed matter, organic molecules, defect centres, semiconductor nanocrystals and heterostructures. As new generations of sources are developed, coupling to cavities and nano-fabrication techniques lead to improved characteristics, delivery rates and spectral ranges. Judging from the brisk pace of recent progress, we expect single photons to soon proceed from demonstrations to applications and to bring with them the first practical uses of quantum information.

  1. Two-photon photoemission from a copper cathode in an X -band photoinjector

    NASA Astrophysics Data System (ADS)

    Li, H.; Limborg-Deprey, C.; Adolphsen, C.; McCormick, D.; Dunning, M.; Jobe, K.; Raubenheimer, T.; Vrielink, A.; Vecchione, T.; Wang, F.; Weathersby, S.

    2016-02-01

    This paper presents two-photon photoemission from a copper cathode in an X -band photoinjector. We experimentally verified that the electron bunch charge from photoemission out of a copper cathode scales with laser intensity (I) square for 400 nm wavelength photons. We compare this two-photon photoemission process with the single photon process at 266 nm. Despite the high reflectivity (R ) of the copper surface for 400 nm photons (R =0.48 ) and higher thermal energy of photoelectrons (two-photon at 200 nm) compared to 266 nm photoelectrons, the quantum efficiency of the two-photon photoemission process (400 nm) exceeds the single-photon process (266 nm) when the incident laser intensity is above 300 GW /cm2 . At the same laser pulse energy (E ) and other experimental conditions, emitted charge scales inversely with the laser pulse duration. A thermal emittance of 2.7 mm-mrad per mm root mean square (rms) was measured on our cathode which exceeds by sixty percent larger compared to the theoretical predictions, but this discrepancy is similar to previous experimental thermal emittance on copper cathodes with 266 nm photons. The damage of the cathode surface of our first-generation X -band gun from both rf breakdowns and laser impacts mostly explains this result. Using a 400 nm laser can substantially simplify the photoinjector system, and make it an alternative solution for compact pulsed electron sources.

  2. 3D holographic polymer photonic crystal for superprism application

    NASA Astrophysics Data System (ADS)

    Chen, Jiaqi; Jiang, Wei; Chen, Xiaonan; Wang, Li; Zhang, Sasa; Chen, Ray T.

    2007-02-01

    Photonic crystal based superprism offers a new way to design new optical components for beam steering and DWDM application. 3D photonic crystals are especially attractive as they could offer more control of the light beam based on the needs. A polygonal prism based holographic fabrication method has been demonstrated for a three-dimensional face-centered-cubic (FCC)-type submicron polymer photonic crystal using SU8 as the photo-sensitive material. Therefore antivibration equipment and complicated optical alignment system are not needed and the requirement for the coherence of the laser source is relaxed compared with the traditional holographic setup. By changing the top-cut prism structure, the polarization of the laser beam, the exposure and development conditions we can achieve different kinds of triclinic or orthorhombic photonic crystals on demand. Special fabrication treatments have been introduced to ensure the survivability of the fabricated large area (cm2) nano-structures. Scanning electron microscopy and diffraction results proved the good uniformity of the fabricated structures. With the proper design of the refraction prism we have achieved a partial bandgap for S+C band (1460-1565nm) in the [111] direction. The transmission and reflection spectra obtained by Fourier transform infrared spectroscopy (FTIR) are in good agreement with simulated band structure. The superprism effects around 1550nm wavelength for the fabricated 3D polymer photonic crystal have been theoretically calculated and such effects can be used for beam steering purpose.

  3. U.S. Regional Agricultural Production in 2030 and 2095: Response to CO2 Fertilization and Hadley Climate Model (HadCM2) Projections of Greenhouse-Forced Climatic Change

    SciTech Connect

    NJ Rosenberg; RC Izaurralde: RA Brown

    1999-11-19

    Research activities underway to evaluate potential consequences of climate change and variability on the agriculture, water resources, and other U.S. sectors were mandated by the Global Change Research Act of 1990. These activities are being carried out in a public-private partnership under the guidance of the U.S. Global Change Research Program. Researchers at Pacific Northwest National Laboratory (PNNL) have been using integrated assessment methodologies to appraise the possible impacts of global warming and climatic variability on the behavior of managed and natural systems. This interim PNNL report contributes to the U.S. National Assessment process with an analysis of the modeled impacts of climatic changes projected by the Hadley/UKMO (HadCM2) general circulation model on agricultural productivity and selected environmental variables. The construction of climatic data for the simulation runs followed general guidelines established by the U.S. National Assessment Synthesis Team. The baseline climate data were obtained from national records for the period 1961 - 1990. The scenario runs for two future periods (2025 - 2030 and 2090 - 2099) were extracted from results of a HadCM2 run distributed at a half-degree spatial resolution. The Erosion Productivity Impact Calculator (EPIC) was used to simulate the behavior of 204 "representative farms" (i.e., soil-climate-management combinations) under baseline climate, the two future periods and their combinations with two levels of atmospheric C02 concentrations (365 and 560 ppm). Analysis of simulation results identified areas in Texas, New Mexico, Colorado, Utah, Arizona, and California that would experience large temperature increases by 2030. Slight cooling is expected by 2030 in parts of Alabama, Florida, Maine, Montana, Idaho, and Utah. Larger areas will experience increased warming by 2095. Uniform precipitation increases are expected by 2030 in the north eastern quarter of the country. These uniform precipitation

  4. Low-voltage back-gated atmospheric pressure chemical vapor deposition based graphene-striped channel transistor with high-κ dielectric showing room-temperature mobility > 11,000 cm(2)/V·s.

    PubMed

    Smith, Casey; Qaisi, Ramy; Liu, Zhihong; Yu, Qingkai; Hussain, Muhammad Mustafa

    2013-07-23

    Utilization of graphene may help realize innovative low-power replacements for III-V materials based high electron mobility transistors while extending operational frequencies closer to the THz regime for superior wireless communications, imaging, and other novel applications. Device architectures explored to date suffer a fundamental performance roadblock due to lack of compatible deposition techniques for nanometer-scale dielectrics required to efficiently modulate graphene transconductance (gm) while maintaining low gate capacitance-voltage product (CgsVgs). Here we show integration of a scaled (10 nm) high-κ gate dielectric aluminum oxide (Al2O3) with an atmospheric pressure chemical vapor deposition (APCVD)-derived graphene channel composed of multiple 0.25 μm stripes to repeatedly realize room-temperature mobility of 11,000 cm(2)/V·s or higher. This high performance is attributed to the APCVD graphene growth quality, excellent interfacial properties of the gate dielectric, conductivity enhancement in the graphene stripes due to low tox/Wgraphene ratio, and scaled high-κ dielectric gate modulation of carrier density allowing full actuation of the device with only ±1 V applied bias. The superior drive current and conductance at Vdd = 1 V compared to other top-gated devices requiring undesirable seed (such as aluminum and poly vinyl alcohol)-assisted dielectric deposition, bottom gate devices requiring excessive gate voltage for actuation, or monolithic (nonstriped) channels suggest that this facile transistor structure provides critical insight toward future device design and process integration to maximize CVD-based graphene transistor performance.

  5. Function photonic crystals

    NASA Astrophysics Data System (ADS)

    Wu, Xiang-Yao; Zhang, Bai-Jun; Yang, Jing-Hai; Liu, Xiao-Jing; Ba, Nuo; Wu, Yi-Heng; Wang, Qing-Cai

    2011-07-01

    In this paper, we present a new kind of function photonic crystals (PCs), whose refractive index is a function of space position. Conventional PCs structure grows from two materials, A and B, with different dielectric constants εA and εB. Based on Fermat principle, we give the motion equations of light in one-dimensional, two-dimensional and three-dimensional function photonic crystals. For one-dimensional function photonic crystals, we give the dispersion relation, band gap structure and transmissivity, and compare them with conventional photonic crystals, and we find the following: (1) For the vertical and non-vertical incidence light of function photonic crystals, there are band gap structures, and for only the vertical incidence light, the conventional PCs have band gap structures. (2) By choosing various refractive index distribution functions n( z), we can obtain more wider or more narrower band gap structure than conventional photonic crystals.

  6. First-photon imaging.

    PubMed

    Kirmani, Ahmed; Venkatraman, Dheera; Shin, Dongeek; Colaço, Andrea; Wong, Franco N C; Shapiro, Jeffrey H; Goyal, Vivek K

    2014-01-01

    Imagers that use their own illumination can capture three-dimensional (3D) structure and reflectivity information. With photon-counting detectors, images can be acquired at extremely low photon fluxes. To suppress the Poisson noise inherent in low-flux operation, such imagers typically require hundreds of detected photons per pixel for accurate range and reflectivity determination. We introduce a low-flux imaging technique, called first-photon imaging, which is a computational imager that exploits spatial correlations found in real-world scenes and the physics of low-flux measurements. Our technique recovers 3D structure and reflectivity from the first detected photon at each pixel. We demonstrate simultaneous acquisition of sub-pulse duration range and 4-bit reflectivity information in the presence of high background noise. First-photon imaging may be of considerable value to both microscopy and remote sensing.

  7. Characterization of radiation damage caused by 23 MeV protons in Multi-Pixel Photon Counter (MPPC)

    NASA Astrophysics Data System (ADS)

    Li, Zhengwei; Xu, Yupeng; Liu, Congzhan; Gu, Yudong; Xie, Fei; Li, Yanguo; Hu, Hongliang; Zhou, Xu; Lu, Xuefeng; Li, Xufang; Zhang, Shuo; Chang, Zhi; Zhang, Juan; Xu, Zhenling; Zhang, Yifei; Zhao, Jianling

    2016-06-01

    A automatic gain control system (AGC) is designed to continuously monitor and automatically control the gain of the phoswich detectors onboard the Hard X-ray Modulation Telescope (HXMT). It consists of a Am241 radioactive source and a photo-detector. The Am241 radioactive source is tagged within a plastic scintillator (BC440M). The scintillating photons produced by the decayed alpha particles from the radioactive source is readout by the photo-detector. The Multi-Pixel Photon Counter (MPPC) produced by Hamamatsu is used as the photo-detector for AGC. To verify the feasibility of its application in space environment, four MPPCs (S10362-33-050C) were irradiated by a beam of 23 MeV protons. The integrated proton fluence that exposed to the four MPPC samples are 1.0 ×108 p cm-2 , 2.0 ×108 p cm-2 , 4.0 ×108 p cm-2 and 1.0 ×1010 p cm-2 respectively. It is found that the increment leakage current of the MPPC samples caused by irradiation damage increase linearly with the integrated fluence. The pulse-height resolution of the MPPC has deteriorated hardly after irradiation. When irradiated up to 1.1 ×109cm-2 1 MeV equivalent neutrons, the MPPC completely lost its photon-counting capability but could still work as a photo-detector for AGC. The MPPC fails as a photo-detector for the AGC when the irradiated 1 MeV neutron equivalent fluences is up to 2.7 ×1010cm-2 .

  8. Two-photon physics

    SciTech Connect

    Bardeen, W.A.

    1981-10-01

    A new experimental frontier has recently been opened to the study of two photon processes. The first results of many aspects of these reactions are being presented at this conference. In contrast, the theoretical development of research ito two photon processes has a much longer history. This talk reviews the many different theoretical ideas which provide a detailed framework for our understanding of two photon processes.

  9. Photonically Engineered Incandescent Emitter

    DOEpatents

    Gee, James M.; Lin, Shawn-Yu; Fleming, James G.; Moreno, James B.

    2005-03-22

    A photonically engineered incandescence is disclosed. The emitter materials and photonic crystal structure can be chosen to modify or suppress thermal radiation above a cutoff wavelength, causing the emitter to selectively emit in the visible and near-infrared portions of the spectrum. An efficient incandescent lamp is enabled thereby. A method for fabricating a three-dimensional photonic crystal of a structural material, suitable for the incandescent emitter, is also disclosed.

  10. Photonic Integrated Circuits

    NASA Technical Reports Server (NTRS)

    Merritt, Scott; Krainak, Michael

    2016-01-01

    Integrated photonics generally is the integration of multiple lithographically defined photonic and electronic components and devices (e.g. lasers, detectors, waveguides passive structures, modulators, electronic control and optical interconnects) on a single platform with nanometer-scale feature sizes. The development of photonic integrated circuits permits size, weight, power and cost reductions for spacecraft microprocessors, optical communication, processor buses, advanced data processing, and integrated optic science instrument optical systems, subsystems and components. This is particularly critical for small spacecraft platforms. We will give an overview of some NASA applications for integrated photonics.

  11. Photon simulated desorption revisited

    NASA Astrophysics Data System (ADS)

    Menzel, D.

    A promising new method for surface investigations is discussed: Photon stimulated desorption. The electronic excitations of adsorbate complexes on surfaces, either by electron impact or photon absorption, which can lead to repulsive states of the complex and therefore to expulsion of ions and neutrals are considered. Such processes are termed electron (or photon) stimulated desorption, ESD and PSD, respectively. Apart from the primary agent (electrons or photons), these processes are similar, and common label "desorption induced by electronic transitions" (acronym DIET) was proposed. Desorption effects, intrinsic photoneffects, and some of the advantages of PSD over ESD are discussed.

  12. Exploring Entangled Two-Photon Absorption in Molecules

    NASA Astrophysics Data System (ADS)

    Caraher, John

    2014-05-01

    Goodson and colleagues have reported anomalously large cross-sections (of order σ =10-17 cm2) for the two-photon absorption of entangled photons in a number of molecules. This poster reports on attempts to replicate and expand upon their results for one of these, zinc tetraphenylporphyrin (Zn TPP) in chloroform solution. It will also discuss the interpretation of the Goodson group's experimental data, particularly their results regarding entanglement area and entanglement time (the spatial and temporal widths of the fourth-order coherence functions, respectively). Results of direct measurement of entanglement time (via a Hong-Ou-Mandel interferometer) for a laser and optical system essentially identical to the one used in Goodson's work will be presented and compared with their reported values. Supported by the DePauw University Faculty Development Committee.

  13. CO2 laser photoacoustic measurements of ethanol absorption coefficients within infrared region of 9.2-10.8 μm

    NASA Astrophysics Data System (ADS)

    Ivascu, I. R.; Matei, C. E.; Patachia, M.; Bratu, A. M.; Dumitras, D. C.

    2016-06-01

    Absorption coefficients of the ethanol vapors at atmospheric pressure and room temperature were measured by photoacoustic technique using a cw, line-tunable, frequency-stabilized CO2 laser as radiation source. The spectrum of the employed CO2 laser includes 54 lines with wavelengths in the infrared region of 9.2-10.8 μm and power levels up to 4.7 W. Measurements revealed a predominant absorption for ethanol within 9.4 μm band of the CO2 laser spectrum, where the highest values of the absorption coefficients were recorded: 3.68 cm- 1 atm- 1 at 9R(20) line and 3.65 cm- 1 atm- 1 at 9R(22) line. The estimated detection range covers six orders of magnitude, from a minimum of 30 ppbV to a maximum of 4% concentration of ethanol in nitrogen, which proves the suitability of the photoacoustic technique for accurate measurements of the ethanol concentration in various applications.

  14. CO2 laser photoacoustic measurements of ethanol absorption coefficients within infrared region of 9.2-10.8 μm.

    PubMed

    Ivascu, I R; Matei, C E; Patachia, M; Bratu, A M; Dumitras, D C

    2016-06-15

    Absorption coefficients of the ethanol vapors at atmospheric pressure and room temperature were measured by photoacoustic technique using a cw, line-tunable, frequency-stabilized CO2 laser as radiation source. The spectrum of the employed CO2 laser includes 54 lines with wavelengths in the infrared region of 9.2-10.8μm and power levels up to 4.7W. Measurements revealed a predominant absorption for ethanol within 9.4μm band of the CO2 laser spectrum, where the highest values of the absorption coefficients were recorded: 3.68cm(-1)atm(-1) at 9R(20) line and 3.65cm(-1)atm(-1) at 9R(22) line. The estimated detection range covers six orders of magnitude, from a minimum of 30ppbV to a maximum of 4% concentration of ethanol in nitrogen, which proves the suitability of the photoacoustic technique for accurate measurements of the ethanol concentration in various applications.

  15. CO2 laser photoacoustic measurements of ethanol absorption coefficients within infrared region of 9.2-10.8 μm.

    PubMed

    Ivascu, I R; Matei, C E; Patachia, M; Bratu, A M; Dumitras, D C

    2016-06-15

    Absorption coefficients of the ethanol vapors at atmospheric pressure and room temperature were measured by photoacoustic technique using a cw, line-tunable, frequency-stabilized CO2 laser as radiation source. The spectrum of the employed CO2 laser includes 54 lines with wavelengths in the infrared region of 9.2-10.8μm and power levels up to 4.7W. Measurements revealed a predominant absorption for ethanol within 9.4μm band of the CO2 laser spectrum, where the highest values of the absorption coefficients were recorded: 3.68cm(-1)atm(-1) at 9R(20) line and 3.65cm(-1)atm(-1) at 9R(22) line. The estimated detection range covers six orders of magnitude, from a minimum of 30ppbV to a maximum of 4% concentration of ethanol in nitrogen, which proves the suitability of the photoacoustic technique for accurate measurements of the ethanol concentration in various applications. PMID:27045783

  16. Resonances in photon-photon scattering

    SciTech Connect

    Chanowitz, M.S.

    1984-11-01

    A quantity called stickiness is introduced which should be largest for J not equal to 0 glueballs and can be measured in two photon scattering and radiative J/psi decay. An argument is reviewed suggesting that light J = 0 glueballs may have large couplings to two photons. The analysis of radiative decays of eta and eta' is reviewed and a plea made to desist from false claims that they are related to GAMMA(..pi../sup 0/ ..-->.. ..gamma gamma..) by SU(3) symmetry. It is shown that two photon studies can refute the difficult-to-refute hypothesis that xi(2220) or zeta(8320) are Higgs bosons. A gallery of rogue resonances and resonance candidates is presented which would usefully be studied in ..gamma gamma.. scattering, including especially the low mass dipion. 34 references.

  17. Ruthenium(II) polypyridyl complexes as mitochondria-targeted two-photon photodynamic anticancer agents.

    PubMed

    Liu, Jiangping; Chen, Yu; Li, Guanying; Zhang, Pingyu; Jin, Chengzhi; Zeng, Leli; Ji, Liangnian; Chao, Hui

    2015-07-01

    Clinical acceptance of photodynamic therapy is currently hindered by poor depth efficacy and inefficient activation of the cell death machinery in cancer cells during treatment. To address these issues, photoactivation using two-photon absorption (TPA) is currently being examined. Mitochondria-targeted therapy represents a promising approach to target tumors selectively and may overcome the resistance in current anticancer therapies. Herein, four ruthenium(II) polypyridyl complexes (RuL1-RuL4) have been designed and developed to act as mitochondria-targeted two-photon photodynamic anticancer agents. These complexes exhibit very high singlet oxygen quantum yields in methanol (0.74-0.81), significant TPA cross sections (124-198 GM), remarkable mitochondrial accumulation, and deep penetration depth. Thus, RuL1-RuL4 were utilized as one-photon and two-photon absorbing photosensitizers in both monolayer cells and 3D multicellular spheroids (MCSs). These Ru(II) complexes were almost nontoxic towards cells and 3D MCSs in the dark and generate sufficient singlet oxygen under one- and two-photon irradiation to trigger cell death. Remarkably, RuL4 exhibited an IC50 value as low as 9.6 μM in one-photon PDT (λirr = 450 nm, 12 J cm(-2)) and 1.9 μM in two-photon PDT (λirr = 830 nm, 800 J cm(-2)) of 3D MCSs; moreover, RuL4 is an order of magnitude more toxic than cisplatin in the latter test system. The combination of mitochondria-targeting and two-photon activation provides a valuable paradigm to develop ruthenium(II) complexes for PDT applications.

  18. Photon mass from inflation.

    PubMed

    Prokopec, Tomislav; Törnkvist, Ola; Woodard, Richard

    2002-09-01

    We consider vacuum polarization from massless scalar electrodynamics in de Sitter inflation. The theory exhibits a 3+1 dimensional analog of the Schwinger mechanism in which a photon mass is dynamically generated. The mechanism is generic for light scalar fields that couple minimally to gravity. The nonvanishing of the photon mass during inflation may result in magnetic fields on cosmological scales.

  19. Photonic layered media

    DOEpatents

    Fleming, James G.; Lin, Shawn-Yu

    2002-01-01

    A new class of structured dielectric media which exhibit significant photonic bandstructure has been invented. The new structures, called photonic layered media, are easy to fabricate using existing layer-by-layer growth techniques, and offer the ability to significantly extend our practical ability to tailor the properties of such optical materials.

  20. Spin-orbit photonics

    NASA Astrophysics Data System (ADS)

    Cardano, Filippo; Marrucci, Lorenzo

    2015-12-01

    Spin-orbit optical phenomena involve the interaction of the photon spin with the light wave propagation and spatial distribution, mediated by suitable optical media. Here we present a short overview of the emerging photonic applications that rely on such effects.

  1. Photon beam position monitor

    DOEpatents

    Kuzay, Tuncer M.; Shu, Deming

    1995-01-01

    A photon beam position monitor for use in the front end of a beamline of a high heat flux and high energy photon source such as a synchrotron radiation storage ring detects and measures the position and, when a pair of such monitors are used in tandem, the slope of a photon beam emanating from an insertion device such as a wiggler or an undulator inserted in the straight sections of the ring. The photon beam position monitor includes a plurality of spaced blades for precisely locating the photon beam, with each blade comprised of chemical vapor deposition (CVD) diamond with an outer metal coating of a photon sensitive metal such as tungsten, molybdenum, etc., which combination emits electrons when a high energy photon beam is incident upon the blade. Two such monitors are contemplated for use in the front end of the beamline, with the two monitors having vertically and horizontally offset detector blades to avoid blade "shadowing". Provision is made for aligning the detector blades with the photon beam and limiting detector blade temperature during operation.

  2. Photon beam position monitor

    DOEpatents

    Kuzay, T.M.; Shu, D.

    1995-02-07

    A photon beam position monitor is disclosed for use in the front end of a beamline of a high heat flux and high energy photon source such as a synchrotron radiation storage ring detects and measures the position and, when a pair of such monitors are used in tandem, the slope of a photon beam emanating from an insertion device such as a wiggler or an undulator inserted in the straight sections of the ring. The photon beam position monitor includes a plurality of spaced blades for precisely locating the photon beam, with each blade comprised of chemical vapor deposition (CVD) diamond with an outer metal coating of a photon sensitive metal such as tungsten, molybdenum, etc., which combination emits electrons when a high energy photon beam is incident upon the blade. Two such monitors are contemplated for use in the front end of the beamline, with the two monitors having vertically and horizontally offset detector blades to avoid blade ''shadowing''. Provision is made for aligning the detector blades with the photon beam and limiting detector blade temperature during operation. 18 figs.

  3. A comparison of small-field tissue phantom ratio data generation methods for an Elekta Agility 6 MV photon beam.

    PubMed

    Richmond, Neil; Brackenridge, Robert

    2014-01-01

    Tissue-phantom ratios (TPRs) are a common dosimetric quantity used to describe the change in dose with depth in tissue. These can be challenging and time consuming to measure. The conversion of percentage depth dose (PDD) data using standard formulae is widely employed as an alternative method in generating TPR. However, the applicability of these formulae for small fields has been questioned in the literature. Functional representation has also been proposed for small-field TPR production. This article compares measured TPR data for small 6 MV photon fields against that generated by conversion of PDD using standard formulae to assess the efficacy of the conversion data. By functionally fitting the measured TPR data for square fields greater than 4cm in length, the TPR curves for smaller fields are generated and compared with measurements. TPRs and PDDs were measured in a water tank for a range of square field sizes. The PDDs were converted to TPRs using standard formulae. TPRs for fields of 4 × 4cm(2) and larger were used to create functional fits. The parameterization coefficients were used to construct extrapolated TPR curves for 1 × 1 cm(2), 2 × 2-cm(2), and 3 × 3-cm(2) fields. The TPR data generated using standard formulae were in excellent agreement with direct TPR measurements. The TPR data for 1 × 1-cm(2), 2 × 2-cm(2), and 3 × 3-cm(2) fields created by extrapolation of the larger field functional fits gave inaccurate initial results. The corresponding mean differences for the 3 fields were 4.0%, 2.0%, and 0.9%. Generation of TPR data using a standard PDD-conversion methodology has been shown to give good agreement with our directly measured data for small fields. However, extrapolation of TPR data using the functional fit to fields of 4 × 4cm(2) or larger resulted in generation of TPR curves that did not compare well with the measured data.

  4. Chirality in photonic systems

    NASA Astrophysics Data System (ADS)

    Solnyshkov, Dmitry; Malpuech, Guillaume

    2016-10-01

    The optical modes of photonic structures are the so-called TE and TM modes that bring intrinsic spin-orbit coupling and chirality to these systems. This, combined with the unique flexibility of design of the photonic potential, and the possibility to mix photon states with excitonic resonances, sensitive to magnetic field and interactions, allows us to achieve many phenomena, often analogous to other solid-state systems. In this contribution, we review in a qualitative and comprehensive way several of these realizations, namely the optical spin Hall effect, the creation of spin currents protected by a non-trivial geometry, the Berry curvature for photons, and the photonic/polaritonic topological insulator.

  5. Ion photon emission microscope

    DOEpatents

    Doyle, Barney L.

    2003-04-22

    An ion beam analysis system that creates microscopic multidimensional image maps of the effects of high energy ions from an unfocussed source upon a sample by correlating the exact entry point of an ion into a sample by projection imaging of the ion-induced photons emitted at that point with a signal from a detector that measures the interaction of that ion within the sample. The emitted photons are collected in the lens system of a conventional optical microscope, and projected on the image plane of a high resolution single photon position sensitive detector. Position signals from this photon detector are then correlated in time with electrical effects, including the malfunction of digital circuits, detected within the sample that were caused by the individual ion that created these photons initially.

  6. A novel photonic oscillator

    NASA Technical Reports Server (NTRS)

    Yao, X. S.; Maleki, L.

    1995-01-01

    We report a novel oscillator for photonic RF systems. This oscillator is capable of generating high-frequency signals up to 70 GHz in both electrical and optical domains and is a special voltage-controlled oscillator with an optical output port. It can be used to make a phase-locked loop (PLL) and perform all functions that a PLL is capable of for photonic systems. It can be synchronized to a reference source by means of optical injection locking, electrical injection locking, and PLL. It can also be self-phase locked and self-injection locked to generate a high-stability photonic RF reference. Its applications include high-frequency reference regeneration and distribution, high-gain frequency multiplication, comb-frequecy and square-wave generation, carrier recovery, and clock recovery. We anticipate that such photonic voltage-controlled oscillators (VCOs) will be as important to photonic RF systems as electrical VCOs are to electrical RF systems.

  7. Nonlinear Photonics 2014: introduction.

    PubMed

    Akhmediev, N; Kartashov, Yaroslav

    2015-01-12

    International Conference "Nonlinear Photonics-2014" took place in Barcelona, Spain on July 27-31, 2014. It was a part of the "Advanced Photonics Congress" which is becoming a traditional notable event in the world of photonics. The current focus issue of Optics Express contains contributions from the participants of the Conference and the Congress. The articles in this focus issue by no means represent the total number of the congress contributions (around 400). However, it demonstrates wide range of topics covered at the event. The next conference of this series is to be held in 2016 in Australia, which is the home of many researchers working in the field of photonics in general and nonlinear photonics in particular.

  8. Roadmap on silicon photonics

    NASA Astrophysics Data System (ADS)

    Thomson, David; Zilkie, Aaron; Bowers, John E.; Komljenovic, Tin; Reed, Graham T.; Vivien, Laurent; Marris-Morini, Delphine; Cassan, Eric; Virot, Léopold; Fédéli, Jean-Marc; Hartmann, Jean-Michel; Schmid, Jens H.; Xu, Dan-Xia; Boeuf, Frédéric; O'Brien, Peter; Mashanovich, Goran Z.; Nedeljkovic, M.

    2016-07-01

    Silicon photonics research can be dated back to the 1980s. However, the previous decade has witnessed an explosive growth in the field. Silicon photonics is a disruptive technology that is poised to revolutionize a number of application areas, for example, data centers, high-performance computing and sensing. The key driving force behind silicon photonics is the ability to use CMOS-like fabrication resulting in high-volume production at low cost. This is a key enabling factor for bringing photonics to a range of technology areas where the costs of implementation using traditional photonic elements such as those used for the telecommunications industry would be prohibitive. Silicon does however have a number of shortcomings as a photonic material. In its basic form it is not an ideal material in which to produce light sources, optical modulators or photodetectors for example. A wealth of research effort from both academia and industry in recent years has fueled the demonstration of multiple solutions to these and other problems, and as time progresses new approaches are increasingly being conceived. It is clear that silicon photonics has a bright future. However, with a growing number of approaches available, what will the silicon photonic integrated circuit of the future look like? This roadmap on silicon photonics delves into the different technology and application areas of the field giving an insight into the state-of-the-art as well as current and future challenges faced by researchers worldwide. Contributions authored by experts from both industry and academia provide an overview and outlook for the silicon waveguide platform, optical sources, optical modulators, photodetectors, integration approaches, packaging, applications of silicon photonics and approaches required to satisfy applications at mid-infrared wavelengths. Advances in science and technology required to meet challenges faced by the field in each of these areas are also addressed together with

  9. Indistinguishability of independent single photons

    NASA Astrophysics Data System (ADS)

    Sun, F. W.; Wong, C. W.

    2009-01-01

    The indistinguishability of independent single photons is presented by decomposing the single photon pulse into the mixed state of different transform-limited pulses. The entanglement between single photons and outer environment or other photons induces the distribution of the center frequencies of those transform-limited pulses and makes photons distinguishable. Only the single photons with the same transform-limited form are indistinguishable. In details, the indistinguishability of single photons from the solid-state quantum emitter and spontaneous parametric down-conversion is examined with two-photon Hong-Ou-Mandel interferometer. Moreover, experimental methods to enhance the indistinguishability are discussed, where the usage of spectral filter is highlighted.

  10. Investigating photonic quantum computation

    NASA Astrophysics Data System (ADS)

    Myers, Casey Robert

    The use of photons as qubits is a promising implementation for quantum computation. The inability of photons to interact, especially with the environment, makes them an ideal physical candidate. However, this also makes them a difficult system to perform two qubit gates on. Recent breakthroughs in photonic quantum computing have shown methods around the requirement of direct photon-photon interaction. In this thesis we study three recently discovered schemes for optical quantum computation. We first investigate the so called linear optical quantum computing (LOQC) scheme, exploring a method to improve the original proposal by constructing a photon-number QND detector that succeeds with a high probability. In doing this we present a new type of LOQC teleporter, one that can detect the presence of a single photon in an arbitrary polarisation state when the input state is a sum of vacuum and multi-photon terms. This new type of teleporter is an improvement on the original scheme in that the entangled states required can be made offline with fewer entangling operations. We next investigate the so called quantum bus (qubus) scheme for photonic quantum computing. We show a scheme to measure the party of n qubit states by using a single qubus mode, controlled rotations and displacements. This allows for the syndrome measurements of any stabilizer quantum error correcting code. We extend these results to a fault tolerant scheme to measure an arbitrary Pauli operator of weight n, incorporating so called single bit teleportations. We investigate the construction of a Toffoli gate by using a single qubus mode, controlled rotations and displacements that works with a success probability of at least 25%. We also investigate the use of single bit teleportations to construct a universal set of gates on coherent state type logic and in the construction of cluster states. We finally investigate the optical Zeno gate, a gate that uses the Zeno effect in the form of two photon

  11. Direct Photons at RHIC

    SciTech Connect

    Gabor,D.

    2008-07-29

    Direct photons are ideal tools to investigate kinematical and thermodynamical conditions of heavy ion collisions since they are emitted from all stages of the collision and once produced they leave the interaction region without further modification by the medium. The PHENIX experiment at RHIC has measured direct photon production in p+p and Au+Au collisions at 200 GeV over a wide transverse momentum (p{sub T}) range. The p+p measurements allow a fundamental test of QCD, and serve as a baseline when we try to disentangle more complex mechanisms producing high p{sub T} direct photons in Au+Au. As for thermal photons in Au+Au we overcome the difficulties due to the large background from hadronic decays by measuring 'almost real' virtual photons which appear as low invariant mass e{sup +}e{sup -} pairs: a significant excess of direct photons is measured above the above next-to-leading order perturbative quantum chromodynamics calculations. Additional insights on the origin of direct photons can be gained with the study of the azimuthal anisotropy which benefits from the increased statistics and reaction plane resolution achieved in RHIC Year-7 data.

  12. Photon detector system

    DOEpatents

    Ekstrom, Philip A.

    1981-01-01

    A photon detector includes a semiconductor device, such as a Schottky barrier diode, which has an avalanche breakdown characteristic. The diode is cooled to cryogenic temperatures to eliminate thermally generated charge carriers from the device. The diode is then biased to a voltage level exceeding the avalanche breakdown threshold level such that, upon receipt of a photon, avalanche breakdown occurs. This breakdown is detected by appropriate circuitry which thereafter reduces the diode bias potential to a level below the avalanche breakdown threshold level to terminate the avalanche condition. Subsequently, the bias potential is reapplied to the diode in preparation for detection of a subsequently received photon.

  13. Photonic Maxwell's Demon.

    PubMed

    Vidrighin, Mihai D; Dahlsten, Oscar; Barbieri, Marco; Kim, M S; Vedral, Vlatko; Walmsley, Ian A

    2016-02-01

    We report an experimental realization of Maxwell's demon in a photonic setup. We show that a measurement at the few-photons level followed by a feed-forward operation allows the extraction of work from intense thermal light into an electric circuit. The interpretation of the experiment stimulates the derivation of an equality relating work extraction to information acquired by measurement. We derive a bound using this relation and show that it is in agreement with the experimental results. Our work puts forward photonic systems as a platform for experiments related to information in thermodynamics.

  14. Photonic structures in biology.

    PubMed

    Vukusic, Pete; Sambles, J Roy

    2003-08-14

    Millions of years before we began to manipulate the flow of light using synthetic structures, biological systems were using nanometre-scale architectures to produce striking optical effects. An astonishing variety of natural photonic structures exists: a species of Brittlestar uses photonic elements composed of calcite to collect light, Morpho butterflies use multiple layers of cuticle and air to produce their striking blue colour and some insects use arrays of elements, known as nipple arrays, to reduce reflectivity in their compound eyes. Natural photonic structures are providing inspiration for technological applications.

  15. Single photon quantum cryptography.

    PubMed

    Beveratos, Alexios; Brouri, Rosa; Gacoin, Thierry; Villing, André; Poizat, Jean-Philippe; Grangier, Philippe

    2002-10-28

    We report the full implementation of a quantum cryptography protocol using a stream of single photon pulses generated by a stable and efficient source operating at room temperature. The single photon pulses are emitted on demand by a single nitrogen-vacancy color center in a diamond nanocrystal. The quantum bit error rate is less that 4.6% and the secure bit rate is 7700 bits/s. The overall performances of our system reaches a domain where single photons have a measurable advantage over an equivalent system based on attenuated light pulses.

  16. Photonic Maxwell's Demon.

    PubMed

    Vidrighin, Mihai D; Dahlsten, Oscar; Barbieri, Marco; Kim, M S; Vedral, Vlatko; Walmsley, Ian A

    2016-02-01

    We report an experimental realization of Maxwell's demon in a photonic setup. We show that a measurement at the few-photons level followed by a feed-forward operation allows the extraction of work from intense thermal light into an electric circuit. The interpretation of the experiment stimulates the derivation of an equality relating work extraction to information acquired by measurement. We derive a bound using this relation and show that it is in agreement with the experimental results. Our work puts forward photonic systems as a platform for experiments related to information in thermodynamics. PMID:26894692

  17. Photon collider Higgs factories

    NASA Astrophysics Data System (ADS)

    Telnov, V. I.

    2014-09-01

    The discovery of the Higgs boson (and still nothing else) have triggered appearance of many proposals of Higgs factories for precision measurement of the Higgs properties. Among them there are several projects of photon colliders (PC) without e+e- in addition to PLC based on e+e- linear colliders ILC and CLIC. In this paper, following a brief discussion of Higgs factories physics program I give an overview of photon colliders based on linear colliders ILC and CLIC, and of the recently proposed photon-collider Higgs factories with no e+e- collision option based on recirculation linacs in ring tunnels.

  18. Photonic Maxwell's Demon

    NASA Astrophysics Data System (ADS)

    Vidrighin, Mihai D.; Dahlsten, Oscar; Barbieri, Marco; Kim, M. S.; Vedral, Vlatko; Walmsley, Ian A.

    2016-02-01

    We report an experimental realization of Maxwell's demon in a photonic setup. We show that a measurement at the few-photons level followed by a feed-forward operation allows the extraction of work from intense thermal light into an electric circuit. The interpretation of the experiment stimulates the derivation of an equality relating work extraction to information acquired by measurement. We derive a bound using this relation and show that it is in agreement with the experimental results. Our work puts forward photonic systems as a platform for experiments related to information in thermodynamics.

  19. Photon physics at RHIC

    SciTech Connect

    Skuja, A.; White, D.H.

    1985-01-01

    Two photon processes induced by heavy ion collisions have been considered. An approximate formalism for calculation is derived. The event rate is interesting at low-photon-photon mass but is limited by the form factor of the nuclei at high mass. The event rate is compared with that at LEP and found to be favorable at the mass of charm mesons but unfavorable at higher masses. It is further noted that two pomeron processes are similar in configuration and are prolific at low pomeron-pomeron masses. 3 refs., 8 figs.

  20. Photonics: Technology project summary

    NASA Technical Reports Server (NTRS)

    Depaula, Ramon P.

    1991-01-01

    Photonics involves the use of light (photons) in conjunction with electronics for applications in communications, computing, control, and sensing. Components used in photonic systems include lasers, optical detectors, optical wave guide devices, fiber optics, and traditional electronic devices. The goal of this program is to develop hybrid optoelectronic devices and systems for sensing, information processing, communications, and control. It is hoped that these new devices will yield at least an order of magnitude improvement in performance over existing technology. The objective of the program is to conduct research and development in the following areas: (1) materials and devices; (2) networking and computing; (3) optical processing/advanced pattern recognition; and (4) sensing.

  1. The effect of entanglement in gravitational photon-photon scattering

    NASA Astrophysics Data System (ADS)

    Rätzel, Dennis; Wilkens, Martin; Menzel, Ralf

    2016-09-01

    The differential cross-section for gravitational photon-photon scattering calculated in perturbative quantum gravity is shown to depend on the degree of polarization entanglement of the two photons. The interaction between photons in the symmetric Bell state is stronger than between not entangled photons. In contrast, the interaction between photons in the anti-symmetric Bell state is weaker than between not entangled photons. The results are interpreted in terms of quantum interference, and it is shown how they fit into the idea of distance-dependent forces.

  2. History and modern applications of nano-composite materials carrying GA/cm2 current density due to a Bose-Einstein Condensate at room temperature produced by Focused Electron Beam Induced Processing for many extraordinary novel technical applications

    NASA Astrophysics Data System (ADS)

    Koops, Hans W. P.

    2015-12-01

    The discovery of Focused Electron Beam Induced Processing and early applications of this technology led to the possible use of a novel nanogranular material “Koops-GranMat®” using Pt/C and Au/C material. which carries at room temperature a current density > 50 times the current density which high TC superconductors can carry. The explanation for the characteristics of this novel material is given. This fact allows producing novel products for many applications using Dual Beam system having a gas supply and X.Y.T stream data programming and not using GDSII layout pattern control software. Novel products are possible for energy transportation. -distribution.-switching, photon-detection above 65 meV energy for very efficient energy harvesting, for bright field emission electron sources used for vacuum electronic devices like amplifiers for HF electronics, micro-tubes, 30 GHz to 6 THz switching amplifiers with signal to noise ratio >10(!), THz power sources up to 1 Watt, in combination with miniaturized vacuum pumps, vacuum gauges, IR to THz detectors, EUV- and X-Ray sources. Since focusing electron beam induced deposition works also at low energy, selfcloning multibeam-production machines for field emitter lamps, displays, multi-beam - lithography, - imaging, and - inspection, energy harvesting, and power distribution with switches controlling field-emitter arrays for KA of currents but with < 100 V switching voltage are possible. Finally the replacement of HTC superconductors and its applications by the Koops-GranMat® having Koops-Pairs at room temperature will allow the investigation devices similar to Josephson Junctions and its applications now called QUIDART (Quantum interference devices at Room Temperature). All these possibilities will support a revolution in the optical, electric, power, and electronic technology.

  3. Microwave background constraints on mixing of photons with hidden photons

    SciTech Connect

    Mirizzi, Alessandro; Redondo, Javier; Sigl, Guenter E-mail: javier.redondo@desy.de

    2009-03-15

    Various extensions of the Standard Model predict the existence of hidden photons kinetically mixing with the ordinary photon. This mixing leads to oscillations between photons and hidden photons, analogous to the observed oscillations between different neutrino flavors. In this context, we derive new bounds on the photon-hidden photon mixing parameters using the high precision cosmic microwave background spectral data collected by the Far Infrared Absolute Spectrophotometer instrument on board of the Cosmic Background Explorer. Requiring the distortions of the CMB induced by the photon-hidden photon mixing to be smaller than experimental upper limits, this leads to a bound on the mixing angle {chi}{sub 0} {approx}< 10{sup -7}-10{sup -5} for hidden photon masses between 10{sup -14} eV and 10{sup -7} eV. This low-mass and low-mixing region of the hidden photon parameter space was previously unconstrained.

  4. Nonlinear Breit-Wheeler process in the collision of a photon with two plane waves

    NASA Astrophysics Data System (ADS)

    Wu, Yuan-Bin; Xue, She-Sheng

    2014-07-01

    The nonlinear Breit-Wheeler process of electron-positron pair production off a probe photon colliding with a low-frequency and a high-frequency electromagnetic wave that propagate in the same direction is analyzed. We calculate the pair-production probability and the spectra of the created pair in the nonlinear Breit-Wheeler processes of pair production off a probe photon colliding with two plane waves or one of these two plane waves. The differences of these two cases are discussed. We evidently show, in the two-wave case, the possibility of Breit-Wheeler pair production with simultaneous photon emission into the low-frequency wave and the high multiphoton phenomena: (i) Breit-Wheeler pair production by absorption of the probe photon and a large number of photons from the low-frequency wave, in addition to the absorption of one photon from the high-frequency wave; (ii) Breit-Wheeler pair production by absorption of the probe photon and one photon from the high-frequency wave with simultaneous emission of a large number of photons into the low-frequency wave. The phenomenon of photon emission into the wave cannot happen in the one-wave case. Compared with the one-wave case, the contributions from high multiphoton processes are largely enhanced in the two-wave case. The results presented in this article show a possible way to access the observations of the phenomenon of photon emission into the wave and high multiphoton phenomenon in Breit-Wheeler pair production even with the laser-beam intensity of order 1018 W/cm2.

  5. Photonic crystal beam splitters.

    PubMed

    Chen, Chii-Chang; Chien, Hung-Da; Luan, Pi-Gang

    2004-11-20

    This work studies two-dimensional photonic crystal beam splitters with two input ports and two output ports. The beam splitter structure consists of two orthogonally crossed line defects and one point defect in square-lattice photonic crystals. The point defect is positioned at the intersection of the line defects to divide the input power into output ports. If the position and the size of the point defect are varied, the power of two output ports can be identical. The beam splitters can be used in photonic crystal Mach-Zehnder interferometers or switches. The simulation results show that a large bandwidth of the extinction ratio larger than 20 dB can be obtained while two beams are interfered in the beam splitters. This enables photonic crystal beam splitters to be used in fiber optic communication systems.

  6. Diamond nonlinear photonics

    NASA Astrophysics Data System (ADS)

    Hausmann, B. J. M.; Bulu, I.; Venkataraman, V.; Deotare, P.; Lončar, M.

    2014-05-01

    Despite progress towards integrated diamond photonics, studies of optical nonlinearities in diamond have been limited to Raman scattering in bulk samples. Diamond nonlinear photonics, however, could enable efficient, in situ frequency conversion of single photons emitted by diamond's colour centres, as well as stable and high-power frequency microcombs operating at new wavelengths. Both of these applications depend crucially on efficient four-wave mixing processes enabled by diamond's third-order nonlinearity. Here, we have realized a diamond nonlinear photonics platform by demonstrating optical parametric oscillation via four-wave mixing using single-crystal ultrahigh-quality-factor (1 × 106) diamond ring resonators operating at telecom wavelengths. Threshold powers as low as 20 mW are measured, and up to 20 new wavelengths are generated from a single-frequency pump laser. We also report the first measurement of the nonlinear refractive index due to the third-order nonlinearity in diamond at telecom wavelengths.

  7. Biophotonics: Circadian photonics

    NASA Astrophysics Data System (ADS)

    Rea, Mark S.

    2011-05-01

    A growing body of medical evidence suggests that disrupting the body's biological clock can have adverse effects on health. Researchers are now creating the photonic tools to monitor, predict and influence the circadian rhythm.

  8. Photon counting: Avalanche inspiration

    NASA Astrophysics Data System (ADS)

    Milburn, Gerard

    2008-07-01

    The ability of a customized avalanche-photodiode detector to distinguish the exact number of photons that it receives will simplify the tools required to perform reliable experiments in quantum optics.

  9. Smart packaging for photonics

    SciTech Connect

    Smith, J.H.; Carson, R.F.; Sullivan, C.T.; McClellan, G.; Palmer, D.W.

    1997-09-01

    Unlike silicon microelectronics, photonics packaging has proven to be low yield and expensive. One approach to make photonics packaging practical for low cost applications is the use of {open_quotes}smart{close_quotes} packages. {open_quotes}Smart{close_quotes} in this context means the ability of the package to actuate a mechanical change based on either a measurement taken by the package itself or by an input signal based on an external measurement. One avenue of smart photonics packaging, the use of polysilicon micromechanical devices integrated with photonic waveguides, was investigated in this research (LDRD 3505.340). The integration of optical components with polysilicon surface micromechanical actuation mechanisms shows significant promise for signal switching, fiber alignment, and optical sensing applications. The optical and stress properties of the oxides and nitrides considered for optical waveguides and how they are integrated with micromechanical devices were investigated.

  10. Photonic band gap materials

    SciTech Connect

    Soukoulis, C.M. |

    1993-12-31

    An overview of the theoretical and experimental efforts in obtaining a photonic band gap, a frequency band in three-dimensional dielectric structures in which electromagnetic waves are forbidden, is presented.

  11. Dispersion in photonic crystals

    NASA Astrophysics Data System (ADS)

    Witzens, Jeremy

    2005-11-01

    Investigations on the dispersive properties of photonic crystals, modified scattering in ring-resonators, monolithic integration of vertical-cavity surface-emitting lasers and advanced data processing techniques for the finite-difference time-domain method are presented. Photonic crystals are periodic mesoscopic arrays of scatterers that modify the propagation properties of electromagnetic waves in a similar way as "natural" crystals modify the properties of electrons in solid-state physics. In this thesis photonic crystals are implemented as planar photonic crystals, i.e., optically thin semiconductor films with periodic arrays of holes etched into them, with a hole-to-hole spacing of the order of the wavelength of light in the dielectric media. Photonic crystals can feature forbidden frequency ranges (the band-gaps) in which light cannot propagate. Even though most work on photonic crystals has focused on these band-gaps for application such as confinement and guiding of light, this thesis focuses on the allowed frequency regions (the photonic bands) and investigates how the propagation of light is modified by the crystal lattice. In particular the guiding of light in bulk photonic crystals in the absence of lattice defects (the self-collimation effect) and the angular steering of light in photonic crystals (the superprism effect) are investigated. The latter is used to design a planar lightwave circuit for frequency domain demultiplexion. Difficulties such as efficient insertion of light into the crystal are resolved and previously predicted limitations on the resolution are circumvented. The demultiplexer is also fabricated and characterized. Monolithic integration of vertical-cavity surface-emitting lasers by means of resonantly enhanced grating couplers is investigated. The grating coupler is designed to bend light through a ninety-degree angle and is characterized with the finite-difference time-domain method. The vertical-cavity surface-emitting lasers are

  12. Photonics Explorer: revolutionizing photonics in the classroom

    NASA Astrophysics Data System (ADS)

    Prasad, Amrita; Debaes, Nathalie; Cords, Nina; Fischer, Robert; Vlekken, Johan; Euler, Manfred; Thienpont, Hugo

    2012-10-01

    The `Photonics Explorer' is a unique intra-curricular optics kit designed to engage, excite and educate secondary school students about the fascination of working with light - hands-on, in their own classrooms. Developed with a pan European collaboration of experts, the kit equips teachers with class sets of experimental material provided within a supporting didactic framework, distributed in conjunction with teacher training courses. The material has been specifically designed to integrate into European science curricula. Each kit contains robust and versatile components sufficient for a class of 25-30 students to work in groups of 2-3. The didactic content is based on guided inquiry-based learning (IBL) techniques with a strong emphasis on hands-on experiments, team work and relating abstract concepts to real world applications. The content has been developed in conjunction with over 30 teachers and experts in pedagogy to ensure high quality and ease of integration. It is currently available in 7 European languages. The Photonics Explorer allows students not only to hone their essential scientific skills but also to really work as scientists and engineers in the classroom. Thus, it aims to encourage more young people to pursue scientific careers and avert the imminent lack of scientific workforce in Europe. 50 Photonics Explorer kits have been successfully tested in 7 European countries with over 1500 secondary school students. The positive impact of the kit in the classroom has been qualitatively and quantitatively evaluated. A non-profit organisation, EYESTvzw [Excite Youth for Engineering Science and Technology], is responsible for the large scale distribution of the Photonics Explorer.

  13. Happy centenary, photon

    NASA Astrophysics Data System (ADS)

    Zeilinger, Anton; Weihs, Gregor; Jennewein, Thomas; Aspelmeyer, Markus

    2005-01-01

    One hundred years ago Albert Einstein introduced the concept of the photon. Although in the early years after 1905 the evidence for the quantum nature of light was not compelling, modern experiments - especially those using photon pairs - have beautifully confirmed its corpuscular character. Research on the quantum properties of light (quantum optics) triggered the evolution of the whole field of quantum information processing, which now promises new technology, such as quantum cryptography and even quantum computers.

  14. QUANTUM CRYPTOGRAPHY: Single Photons.

    PubMed

    Benjamin, S

    2000-12-22

    Quantum cryptography offers the potential of totally secure transfer of information, but as Benjamin discusses in this Perspective, its practical implementation hinges on being able to generate single photons (rather than two or more) at a time. Michler et al. show how this condition can be met in a quantum dot microdisk structure. Single molecules were also recently shown to allow controlled single-photon emission.

  15. Ultrastable Multigigahertz Photonic Oscillator

    NASA Technical Reports Server (NTRS)

    Logan, Ronald T., Jr.

    1996-01-01

    Novel photonic oscillator developed to serve as ultrastable source of microwave and millimeter-wave signals. In system, oscillations generated photonically, then converted to electronic form. Includes self-mode-locked semiconductor laser producing stream of pulses, detected and fed back to laser as input. System also includes fiber-optic-delay-line discriminator, which detects fluctuations of self-mode-locking frequency and generates error signal used in negative-feedback loop to stabilize pulse-repetition frequency.

  16. Photon structure function

    SciTech Connect

    Bardeen, W.A.

    1980-11-01

    Theoretical understanding of the photon structure function is reviewed. As an illustration of the pointlike component, the parton model is briefly discussed. However, the systematic study of the photon structure function is presented through the framework of the operator product expansion. Perturbative QCD is used as the theoretical basis for the calculation of leading contributions to the operator product expansion. The influence of higher order QCD effects on these results is discussed. Recent results for the polarized structure functions are discussed.

  17. Photonic band structure

    SciTech Connect

    Yablonovitch, E.

    1993-05-01

    We learned how to create 3-dimensionally periodic dielectric structures which are to photon waves, as semiconductor crystals are to electron waves. That is, these photonic crystals have a photonic bandgap, a band of frequencies in which electromagnetic waves are forbidden, irrespective of propagation direction in space. Photonic bandgaps provide for spontaneous emission inhibition and allow for a new class of electromagnetic micro-cavities. If the perfect 3-dimensional periodicity is broken by a local defect, then local electromagnetic modes can occur within the forbidden bandgap. The addition of extra dielectric material locally, inside the photonic crystal, produces {open_quotes}donor{close_quotes} modes. Conversely, the local removal of dielectric material from the photonic crystal produces {open_quotes}acceptor{close_quotes} modes. Therefore, it will now be possible to make high-Q electromagnetic cavities of volume {approx_lt}1 cubic wavelength, for short wavelengths at which metallic cavities are useless. These new dielectric micro-resonators can cover the range all the way from millimeter waves, down to ultraviolet wavelengths.

  18. Photonic quantum technologies

    NASA Astrophysics Data System (ADS)

    O'Brien, Jeremy

    2013-03-01

    Of the approaches to quantum computing, photons are appealing for their low-noise properties and ease of manipulation, and relevance to other quantum technologies, including communication, metrology and measurement. We report an integrated waveguide approach to photonic quantum circuits for high performance, miniaturization and scalability [6-10]. We address the challenges of scaling up quantum circuits using new insights into how controlled operations can be efficiently realised, demonstrating Shor's algorithm with consecutive CNOT gates and the iterative phase estimation algorithm. We have shown how quantum circuits can be reconfigured, using thermo-optic phase shifters to realise a highly reconfigurable quantum circuit, and electro-optic phase shifters in lithium niobate to rapidly manipulate the path and polarisation of telecomm wavelength single photons. We have addressed miniaturisation using multimode interference architectures to directly implement NxN Hadamard operations, and by using high refractive index contrast materials such as SiOxNy, in which we have implemented quantum walks of correlated photons, and Si, in which we have demonstrated generation of orbital angular momentum states of light. We have incorporated microfluidic channels for the delivery of samples to measure the concentration of a blood protein with entangled states of light. We have begun to address the integration of superconducting single photon detectors and diamond and non-linear single photon sources. Finally, we give an overview of recent work on fundamental aspects of quantum measurement, including a quantum version of Wheeler's delayed choice experiment.

  19. Evidence for a 3 X 10^8 M_⊙ Black Hole in NGC 7052 from Hubble Space Telescope Observations of the Nuclear Gas Disk

    NASA Astrophysics Data System (ADS)

    van der Marel, Roeland P.; van den Bosch, Frank C.

    1998-11-01

    We present a Hubble Space Telescope (HST) study of the nuclear region of the E4 radio galaxy NGC 7052, which has a nuclear disk of dust and gas. The Second Wide Field and Planetary Camera (WFPC2) was used to obtain B, V, and I broadband images and an Hα + [N II] narrowband image. The images yield the stellar surface brightness profile, the optical depth of the dust, and the flux distribution of the ionized gas. The Faint Object Spectrograph was used to obtain Hα + [N II] spectra at six different positions along the major axis, using a 0.26" diameter circular aperture. The emission lines yield the rotation curve of the ionized gas and the radial profile of its velocity dispersion. The observed rotation velocity at r = 0.2" from the nucleus is V = 155 +/- 17 km s^-1. The Gaussian dispersion of the emission lines increases from sigma ~ 70 km s^-1 at r = 1" to sigma ~ 400 km s^-1 on the nucleus. To interpret the gas kinematics, we construct axisymmetric models in which the gas and dust reside in a disk in the equatorial plane of the stellar body and are viewed at an inclination of 70 deg. It is assumed that the gas moves on circular orbits, with an intrinsic velocity dispersion due to turbulence (or otherwise nongravitational motion). The latter is required to fit the observed increase in the line widths toward the nucleus and must reach a value in excess of 500 km s^-1 in the central 0.1". The circular velocity is calculated from the combined gravitational potential of the stars and a possible nuclear black hole. Models without a black hole predict a rotation curve that is shallower than observed (V_pred = 92 km s^-1 at r = 0.2") and are ruled out at greater than 99% confidence. Models with a black hole of mass M_a=3.3^+2.3_-1.3x10^8 M_⊙ provide an acceptable fit. The best-fitting model with a black hole adequately reproduces the observed emission-line shapes on the nucleus, which have a narrower peak and broader wings than a Gaussian. NGC 7052 can be added to the

  20. Multi-photon absorption limits to heralded single photon sources

    PubMed Central

    Husko, Chad A.; Clark, Alex S.; Collins, Matthew J.; De Rossi, Alfredo; Combrié, Sylvain; Lehoucq, Gaëlle; Rey, Isabella H.; Krauss, Thomas F.; Xiong, Chunle; Eggleton, Benjamin J.

    2013-01-01

    Single photons are of paramount importance to future quantum technologies, including quantum communication and computation. Nonlinear photonic devices using parametric processes offer a straightforward route to generating photons, however additional nonlinear processes may come into play and interfere with these sources. Here we analyse spontaneous four-wave mixing (SFWM) sources in the presence of multi-photon processes. We conduct experiments in silicon and gallium indium phosphide photonic crystal waveguides which display inherently different nonlinear absorption processes, namely two-photon (TPA) and three-photon absorption (ThPA), respectively. We develop a novel model capturing these diverse effects which is in excellent quantitative agreement with measurements of brightness, coincidence-to-accidental ratio (CAR) and second-order correlation function g(2)(0), showing that TPA imposes an intrinsic limit on heralded single photon sources. We build on these observations to devise a new metric, the quantum utility (QMU), enabling further optimisation of single photon sources. PMID:24186400

  1. Multi-photon absorption limits to heralded single photon sources

    NASA Astrophysics Data System (ADS)

    Husko, Chad A.; Clark, Alex S.; Collins, Matthew J.; de Rossi, Alfredo; Combrié, Sylvain; Lehoucq, Gaëlle; Rey, Isabella H.; Krauss, Thomas F.; Xiong, Chunle; Eggleton, Benjamin J.

    2013-11-01

    Single photons are of paramount importance to future quantum technologies, including quantum communication and computation. Nonlinear photonic devices using parametric processes offer a straightforward route to generating photons, however additional nonlinear processes may come into play and interfere with these sources. Here we analyse spontaneous four-wave mixing (SFWM) sources in the presence of multi-photon processes. We conduct experiments in silicon and gallium indium phosphide photonic crystal waveguides which display inherently different nonlinear absorption processes, namely two-photon (TPA) and three-photon absorption (ThPA), respectively. We develop a novel model capturing these diverse effects which is in excellent quantitative agreement with measurements of brightness, coincidence-to-accidental ratio (CAR) and second-order correlation function g(2)(0), showing that TPA imposes an intrinsic limit on heralded single photon sources. We build on these observations to devise a new metric, the quantum utility (QMU), enabling further optimisation of single photon sources.

  2. Comparison of Head Scatter Factor for 6MV and 10MV flattened (FB) and Unflattened (FFF) Photon Beam using indigenously Designed Columnar Mini Phantom

    PubMed Central

    Ashokkumar, Sigamani; Nambi Raj, N Arunai; Sinha, Sujit Nath; Yadav, Girigesh; Thiyagarajan, Rajesh; Raman, Kothanda; Mishra, Manindra Bhushan

    2014-01-01

    To measure and compare the head scatter factor for flattened (FB) and unflattened (FFF) of 6MV and 10MV photon beam using indigenously designed mini phantom. A columnar mini phantom was designed as recommended by AAPM Task Group 74 with low and high atomic number materials at 10 cm (mini phantom) and at approximately twice the depth of maximum dose water equivalent thickness (brass build-up cap). Scatter in the accelerator (Sc) values of 6MV-FFF photon beams are lesser than that of the 6MV-FB photon beams (0.66-2.8%; Clinac iX, 2300CD) and (0.47-1.74%; True beam) for field sizes ranging from 10 × 10 cm2 to 40 × 40 cm2. Sc values of 10MV-FFF photon beams are lesser (0.61-2.19%; True beam) than that of the 10MV-FB photons beams for field sizes ranging from 10 × 10 cm2 to 40 × 40 cm2. The SSD had no influence on head scatter for both flattened and unflattened beams and irrespective of head design of the different linear accelerators. The presence of field shaping device influences the Sc values. The collimator exchange effect reveals that the opening of the upper jaw increases Sc irrespective of FB or FFF photon beams and different linear accelerators, and it is less significant in FFF beams. Sc values of 6MV-FB square field were in good agreement with that of AAPM, TG-74 published data for Varian (Clinac iX, 2300CD) accelerator. Our results confirm that the removal of flattening filter decreases in the head scatter factor compared to flattened beam. This could reduce the out-of-field dose in advanced treatment delivery techniques. PMID:25190997

  3. Comparison of Head Scatter Factor for 6MV and 10MV flattened (FB) and Unflattened (FFF) Photon Beam using indigenously Designed Columnar Mini Phantom.

    PubMed

    Ashokkumar, Sigamani; Nambi Raj, N Arunai; Sinha, Sujit Nath; Yadav, Girigesh; Thiyagarajan, Rajesh; Raman, Kothanda; Mishra, Manindra Bhushan

    2014-07-01

    To measure and compare the head scatter factor for flattened (FB) and unflattened (FFF) of 6MV and 10MV photon beam using indigenously designed mini phantom. A columnar mini phantom was designed as recommended by AAPM Task Group 74 with low and high atomic number materials at 10 cm (mini phantom) and at approximately twice the depth of maximum dose water equivalent thickness (brass build-up cap). Scatter in the accelerator (Sc) values of 6MV-FFF photon beams are lesser than that of the 6MV-FB photon beams (0.66-2.8%; Clinac iX, 2300CD) and (0.47-1.74%; True beam) for field sizes ranging from 10 × 10 cm(2) to 40 × 40 cm(2). Sc values of 10MV-FFF photon beams are lesser (0.61-2.19%; True beam) than that of the 10MV-FB photons beams for field sizes ranging from 10 × 10 cm(2) to 40 × 40 cm(2). The SSD had no influence on head scatter for both flattened and unflattened beams and irrespective of head design of the different linear accelerators. The presence of field shaping device influences the Sc values. The collimator exchange effect reveals that the opening of the upper jaw increases Sc irrespective of FB or FFF photon beams and different linear accelerators, and it is less significant in FFF beams. Sc values of 6MV-FB square field were in good agreement with that of AAPM, TG-74 published data for Varian (Clinac iX, 2300CD) accelerator. Our results confirm that the removal of flattening filter decreases in the head scatter factor compared to flattened beam. This could reduce the out-of-field dose in advanced treatment delivery techniques.

  4. Two-photon interference with non-identical photons

    NASA Astrophysics Data System (ADS)

    Liu, Jianbin; Zhou, Yu; Zheng, Huaibin; Chen, Hui; Li, Fu-li; Xu, Zhuo

    2015-11-01

    Two-photon interference with non-identical photons is studied based on the superposition principle in Feynman's path integral theory. The second-order temporal interference pattern is observed by superposing laser and pseudothermal light beams with different spectra. The reason why there is two-photon interference for photons of different spectra is that non-identical photons can be indistinguishable for the detection system when Heisenberg's uncertainty principle is taken into account. These studies are helpful to understand the second-order interference of light in the language of photons.

  5. CMOS-compatible photonic devices for single-photon generation

    NASA Astrophysics Data System (ADS)

    Xiong, Chunle; Bell, Bryn; Eggleton, Benjamin J.

    2016-09-01

    Sources of single photons are one of the key building blocks for quantum photonic technologies such as quantum secure communication and powerful quantum computing. To bring the proof-of-principle demonstration of these technologies from the laboratory to the real world, complementary metal-oxide-semiconductor (CMOS)-compatible photonic chips are highly desirable for photon generation, manipulation, processing and even detection because of their compactness, scalability, robustness, and the potential for integration with electronics. In this paper, we review the development of photonic devices made from materials (e.g., silicon) and processes that are compatible with CMOS fabrication facilities for the generation of single photons.

  6. EDITORIAL: Photonic Crystal Devices

    NASA Astrophysics Data System (ADS)

    Bhattacharya, Pallab K.

    2007-05-01

    The engineering of electromagnetic modes at optical frequencies in artificial dielectric structures with periodic and random variation of the refractive index, enabling control of the radiative properties of the materials and photon localization, was first proposed independently by Yablonovitch and John in 1987. It is possible to control the flow of light in the periodic dielectric structures, known as photonic crystals (PC). As light waves scatter within the photonic crystal, destructive interference cancels out light of certain wavelengths, thereby forming a photonic bandgap, similar to the energy bandgap for electron waves in a semiconductor. Photons whose energies lie within the gap cannot propagate through the periodic structure. This property can be used to make a low-loss cavity. If a point defect, such as one or more missing periods, is introduced into the periodic structure a region is obtained within which the otherwise forbidden wavelengths can be locally trapped. This property can be used to realize photonic microcavities. Similarly, a line of defects can serve as a waveguide. While the realization of three-dimensional (3D) photonic crystals received considerable attention initially, planar two-dimensional (2D) structures are currently favoured because of their relative ease of fabrication. 2D photonic crystal structures provide most of the functionality of 3D structures. These attributes have generated worldwide research and development of sub-μm and μm size active and passive photonic devices such as single-mode and non- classical light sources, guided wave devices, resonant cavity detection, and components for optical communication. More recently, photonic crystal guided wave devices are being investigated for application in microfludic and biochemical sensing. Photonic crystal devices have been realized with bulk, quantum well and quantum dot active regions. The Cluster of articles in this issue of Journal of Physics D: Applied Physics provides a

  7. Effect of Doppler-shifted photons on subnanosecond breakdown in high-voltage pulse discharge

    NASA Astrophysics Data System (ADS)

    Schweigert, I. V.; Alexandrov, A. L.; Zakrevsky, Dm. E.; Bokhan, P. A.

    2016-06-01

    The experiments in high-voltage open discharge in helium [1, 2] showed a controlled current growth rate of 500 A/(cm2ns) for an applied voltage of 20 kV and gas pressure of 6 Torr. A kinetic model of the subnanosecond breakdown is developed to analyze the mechanism of current growth, which takes into account the kinetics of electrons, ions, fast atoms and photons with a Doppler shift (DS). DS photons appear in discharge due to collisions of heavy particles. Using particle in cell simulations, we show a critical role of DS photons in the electron emission from the cathode during the breakdown. Our experimental and calculation results show a decrease of the breakdown time with increasing gas pressure from 3 Torr to 16 Torr.

  8. Two-dimensional photonic crystal bandedge laser with hybrid perovskite thin film for optical gain

    NASA Astrophysics Data System (ADS)

    Cha, Hyungrae; Bae, Seunghwan; Lee, Myungjae; Jeon, Heonsu

    2016-05-01

    We report optically pumped room temperature single mode laser that contains a thin film of hybrid perovskite, an emerging photonic material, as gain medium. Two-dimensional square lattice photonic crystal (PhC) backbone structure enables single mode laser operation via a photonic bandedge mode, while a thin film of methyl-ammonium lead iodide (CH3NH3PbI3) spin-coated atop provides optical gain for lasing. Two kinds of bandedge modes, Γ and M, are employed, and both devices laser in single mode at similar laser thresholds of ˜200 μJ/cm2 in pulse energy density. Polarization dependence measurements reveal a clear difference between the two kinds of bandedge lasers: isotropic for the Γ-point laser and highly anisotropic for the M-point laser. These observations are consistent with expected modal properties, confirming that the lasing actions indeed originate from the corresponding PhC bandedge modes.

  9. Estimation of photoneutron intensities around radiotherapy linear accelerator 23-MV photon beam.

    PubMed

    Shweikani, R; Anjak, O

    2015-05-01

    CR-39 solid-state nuclear track detectors (SSNTDs) were used to study the variations of fast neutron relative intensities around a high-energy (23MV) linear accelerator (Varian 21EX) photon beam. The variations were determined on the patient plane at 0, 50, 100, 150 and 200cm from the isocenter of the photon beam. In addition, photoneutron intensities and distributions at isocenter level with field size of 40×40cm(2) at Source Axis Distance (SAD)=100cm around 23MV photon beam were also determined. The results showed that the photoneutron intensities decreased rapidly by increasing the distance from the center of the x-ray beam towards the periphery, for the open fields.

  10. Photonic topological insulators.

    PubMed

    Khanikaev, Alexander B; Mousavi, S Hossein; Tse, Wang-Kong; Kargarian, Mehdi; MacDonald, Allan H; Shvets, Gennady

    2013-03-01

    Recent progress in understanding the topological properties of condensed matter has led to the discovery of time-reversal-invariant topological insulators. A remarkable and useful property of these materials is that they support unidirectional spin-polarized propagation at their surfaces. Unfortunately topological insulators are rare among solid-state materials. Using suitably designed electromagnetic media (metamaterials) we theoretically demonstrate a photonic analogue of a topological insulator. We show that metacrystals-superlattices of metamaterials with judiciously designed properties-provide a platform for designing topologically non-trivial photonic states, similar to those that have been identified for condensed-matter topological insulators. The interfaces of the metacrystals support helical edge states that exhibit spin-polarized one-way propagation of photons, robust against disorder. Our results demonstrate the possibility of attaining one-way photon transport without application of external magnetic fields or breaking of time-reversal symmetry. Such spin-polarized one-way transport enables exotic spin-cloaked photon sources that do not obscure each other.

  11. Nonlinear silicon photonics

    NASA Astrophysics Data System (ADS)

    Tsia, Kevin K.; Jalali, Bahram

    2010-05-01

    An intriguing optical property of silicon is that it exhibits a large third-order optical nonlinearity, with orders-ofmagnitude larger than that of silica glass in the telecommunication band. This allows efficient nonlinear optical interaction at relatively low power levels in a small footprint. Indeed, we have witnessed a stunning progress in harnessing the Raman and Kerr effects in silicon as the mechanisms for enabling chip-scale optical amplification, lasing, and wavelength conversion - functions that until recently were perceived to be beyond the reach of silicon. With all the continuous efforts developing novel techniques, nonlinear silicon photonics is expected to be able to reach even beyond the prior achievements. Instead of providing a comprehensive overview of this field, this manuscript highlights a number of new branches of nonlinear silicon photonics, which have not been fully recognized in the past. In particular, they are two-photon photovoltaic effect, mid-wave infrared (MWIR) silicon photonics, broadband Raman effects, inverse Raman scattering, and periodically-poled silicon (PePSi). These novel effects and techniques could create a new paradigm for silicon photonics and extend its utility beyond the traditionally anticipated applications.

  12. Antigravity Acts on Photons

    NASA Astrophysics Data System (ADS)

    Brynjolfsson, Ari

    2002-04-01

    Einstein's general theory of relativity assumes that photons don't change frequency as they move from Sun to Earth. This assumption is correct in classical physics. All experiments proving the general relativity are in the domain of classical physics. This include the tests by Pound et al. of the gravitational redshift of 14.4 keV photons; the rocket experiments by Vessot et al.; the Galileo solar redshift experiments by Krisher et al.; the gravitational deflection of light experiments by Riveros and Vucetich; and delay of echoes of radar signals passing close to Sun as observed by Shapiro et al. Bohr's correspondence principle assures that quantum mechanical theory of general relativity agrees with Einstein's classical theory when frequency and gravitational field gradient approach zero, or when photons cannot interact with the gravitational field. When we treat photons as quantum mechanical particles; we find that gravitational force on photons is reversed (antigravity). This modified theory contradicts the equivalence principle, but is consistent with all experiments. Solar lines and distant stars are redshifted in accordance with author's plasma redshift theory. These changes result in a beautiful consistent cosmology.

  13. Photonics for life.

    PubMed

    Cubeddu, Rinaldo; Bassi, Andrea; Comelli, Daniela; Cova, Sergio; Farina, Andrea; Ghioni, Massimo; Rech, Ivan; Pifferi, Antonio; Spinelli, Lorenzo; Taroni, Paola; Torricelli, Alessandro; Tosi, Alberto; Valentini, Gianluca; Zappa, Franco

    2011-01-01

    Light is strictly connected with life, and its presence is fundamental for any living environment. Thus, many biological mechanisms are related to light interaction or can be evaluated through processes involving energy exchange with photons. Optics has always been a precious tool to evaluate molecular and cellular mechanisms, but the discovery of lasers opened new pathways of interactions of light with biological matter, pushing an impressive development for both therapeutic and diagnostic applications in biomedicine. The use of light in different fields has become so widespread that the word photonics has been utilized to identify all the applications related to processes where the light is involved. The photonics area covers a wide range of wavelengths spanning from soft X-rays to mid-infrared and includes all devices related to photons as light sources, optical fibers and light guides, detectors, and all the related electronic equipment. The recent use of photons in the field of telecommunications has pushed the technology toward low-cost, compact, and efficient devices, making them available for many other applications, including those related to biology and medicine where these requirements are of particular relevance. Moreover, basic sciences such as physics, chemistry, mathematics, and electronics have recognized the interdisciplinary need of biomedical science and are translating the most advanced researches into these fields. The Politecnico school has pioneered many of them,and this article reviews the state of the art of biomedical research at the Politecnico in the field internationally known as biophotonics.

  14. Photonic Crystal Microchip Laser

    PubMed Central

    Gailevicius, Darius; Koliadenko, Volodymyr; Purlys, Vytautas; Peckus, Martynas; Taranenko, Victor; Staliunas, Kestutis

    2016-01-01

    The microchip lasers, being very compact and efficient sources of coherent light, suffer from one serious drawback: low spatial quality of the beam strongly reducing the brightness of emitted radiation. Attempts to improve the beam quality, such as pump-beam guiding, external feedback, either strongly reduce the emission power, or drastically increase the size and complexity of the lasers. Here it is proposed that specially designed photonic crystal in the cavity of a microchip laser, can significantly improve the beam quality. Experiments show that a microchip laser, due to spatial filtering functionality of intracavity photonic crystal, improves the beam quality factor M2 reducing it by a factor of 2, and increase the brightness of radiation by a factor of 3. This comprises a new kind of laser, the “photonic crystal microchip laser”, a very compact and efficient light source emitting high spatial quality high brightness radiation. PMID:27683066

  15. Photon physics with PHENIX

    SciTech Connect

    White, S.

    1995-07-15

    In this Paper the author discusses briefly the physics motivation for extending measurements of particle production with high granularity and particle id capabilities to neutrals in PHENIX. The author then discusses the technique of direct photon measurement in the presence of copious background photons from {pi}{sup o} decays. The experiment will measure relatively low p{sub t} photons near y=0 in the lab frame. This new experimental environment of high multiplicity and low {gamma} momenta will affect both the techniques used and the type of analysis which can be performed. The Phenix Electromagnetic calorimeter is described and its capabilities illustrated with results from simulation and beam tests of the first production array.

  16. Sensing individual terahertz photons.

    PubMed

    Hashiba, Hideomi; Antonov, Vladimir; Kulik, Leonid; Tzalenchuk, Alexander; Komiyama, Susumu

    2010-04-23

    One of the promising ways to perform single-photon counting of terahertz radiation consists in sensitive probing of plasma excitation in the electron gas upon photon absorption. We demonstrate the ultimate sensor operating on this principle. It is assembled from a GaAs/AlGaAs quantum dot, electron reservoir and superconducting single-electron transistor. The quantum dot is isolated from the surrounding electron reservoir in such a way that when the excited plasma wave decays, an electron could tunnel off the dot to the reservoir. The resulting charge polarization of the dot is detected with the single-electron transistor. Such a system forms an easy-to-use sensor enabling single-photon counting in a very obscure wavelength region.

  17. Photonic Crystal Microchip Laser

    NASA Astrophysics Data System (ADS)

    Gailevicius, Darius; Koliadenko, Volodymyr; Purlys, Vytautas; Peckus, Martynas; Taranenko, Victor; Staliunas, Kestutis

    2016-09-01

    The microchip lasers, being very compact and efficient sources of coherent light, suffer from one serious drawback: low spatial quality of the beam strongly reducing the brightness of emitted radiation. Attempts to improve the beam quality, such as pump-beam guiding, external feedback, either strongly reduce the emission power, or drastically increase the size and complexity of the lasers. Here it is proposed that specially designed photonic crystal in the cavity of a microchip laser, can significantly improve the beam quality. Experiments show that a microchip laser, due to spatial filtering functionality of intracavity photonic crystal, improves the beam quality factor M2 reducing it by a factor of 2, and increase the brightness of radiation by a factor of 3. This comprises a new kind of laser, the “photonic crystal microchip laser”, a very compact and efficient light source emitting high spatial quality high brightness radiation.

  18. Photonic Floquet topological insulators.

    PubMed

    Rechtsman, Mikael C; Zeuner, Julia M; Plotnik, Yonatan; Lumer, Yaakov; Podolsky, Daniel; Dreisow, Felix; Nolte, Stefan; Segev, Mordechai; Szameit, Alexander

    2013-04-11

    Topological insulators are a new phase of matter, with the striking property that conduction of electrons occurs only on their surfaces. In two dimensions, electrons on the surface of a topological insulator are not scattered despite defects and disorder, providing robustness akin to that of superconductors. Topological insulators are predicted to have wide-ranging applications in fault-tolerant quantum computing and spintronics. Substantial effort has been directed towards realizing topological insulators for electromagnetic waves. One-dimensional systems with topological edge states have been demonstrated, but these states are zero-dimensional and therefore exhibit no transport properties. Topological protection of microwaves has been observed using a mechanism similar to the quantum Hall effect, by placing a gyromagnetic photonic crystal in an external magnetic field. But because magnetic effects are very weak at optical frequencies, realizing photonic topological insulators with scatter-free edge states requires a fundamentally different mechanism-one that is free of magnetic fields. A number of proposals for photonic topological transport have been put forward recently. One suggested temporal modulation of a photonic crystal, thus breaking time-reversal symmetry and inducing one-way edge states. This is in the spirit of the proposed Floquet topological insulators, in which temporal variations in solid-state systems induce topological edge states. Here we propose and experimentally demonstrate a photonic topological insulator free of external fields and with scatter-free edge transport-a photonic lattice exhibiting topologically protected transport of visible light on the lattice edges. Our system is composed of an array of evanescently coupled helical waveguides arranged in a graphene-like honeycomb lattice. Paraxial diffraction of light is described by a Schrödinger equation where the propagation coordinate (z) acts as 'time'. Thus the helicity of the

  19. Photonic Floquet topological insulators.

    PubMed

    Rechtsman, Mikael C; Zeuner, Julia M; Plotnik, Yonatan; Lumer, Yaakov; Podolsky, Daniel; Dreisow, Felix; Nolte, Stefan; Segev, Mordechai; Szameit, Alexander

    2013-04-11

    Topological insulators are a new phase of matter, with the striking property that conduction of electrons occurs only on their surfaces. In two dimensions, electrons on the surface of a topological insulator are not scattered despite defects and disorder, providing robustness akin to that of superconductors. Topological insulators are predicted to have wide-ranging applications in fault-tolerant quantum computing and spintronics. Substantial effort has been directed towards realizing topological insulators for electromagnetic waves. One-dimensional systems with topological edge states have been demonstrated, but these states are zero-dimensional and therefore exhibit no transport properties. Topological protection of microwaves has been observed using a mechanism similar to the quantum Hall effect, by placing a gyromagnetic photonic crystal in an external magnetic field. But because magnetic effects are very weak at optical frequencies, realizing photonic topological insulators with scatter-free edge states requires a fundamentally different mechanism-one that is free of magnetic fields. A number of proposals for photonic topological transport have been put forward recently. One suggested temporal modulation of a photonic crystal, thus breaking time-reversal symmetry and inducing one-way edge states. This is in the spirit of the proposed Floquet topological insulators, in which temporal variations in solid-state systems induce topological edge states. Here we propose and experimentally demonstrate a photonic topological insulator free of external fields and with scatter-free edge transport-a photonic lattice exhibiting topologically protected transport of visible light on the lattice edges. Our system is composed of an array of evanescently coupled helical waveguides arranged in a graphene-like honeycomb lattice. Paraxial diffraction of light is described by a Schrödinger equation where the propagation coordinate (z) acts as 'time'. Thus the helicity of the

  20. Photonic hydrogel sensors.

    PubMed

    Yetisen, Ali K; Butt, Haider; Volpatti, Lisa R; Pavlichenko, Ida; Humar, Matjaž; Kwok, Sheldon J J; Koo, Heebeom; Kim, Ki Su; Naydenova, Izabela; Khademhosseini, Ali; Hahn, Sei Kwang; Yun, Seok Hyun

    2016-01-01

    Analyte-sensitive hydrogels that incorporate optical structures have emerged as sensing platforms for point-of-care diagnostics. The optical properties of the hydrogel sensors can be rationally designed and fabricated through self-assembly, microfabrication or laser writing. The advantages of photonic hydrogel sensors over conventional assay formats include label-free, quantitative, reusable, and continuous measurement capability that can be integrated with equipment-free text or image display. This Review explains the operation principles of photonic hydrogel sensors, presents syntheses of stimuli-responsive polymers, and provides an overview of qualitative and quantitative readout technologies. Applications in clinical samples are discussed, and potential future directions are identified. PMID:26485407

  1. Photonic hydrogel sensors.

    PubMed

    Yetisen, Ali K; Butt, Haider; Volpatti, Lisa R; Pavlichenko, Ida; Humar, Matjaž; Kwok, Sheldon J J; Koo, Heebeom; Kim, Ki Su; Naydenova, Izabela; Khademhosseini, Ali; Hahn, Sei Kwang; Yun, Seok Hyun

    2016-01-01

    Analyte-sensitive hydrogels that incorporate optical structures have emerged as sensing platforms for point-of-care diagnostics. The optical properties of the hydrogel sensors can be rationally designed and fabricated through self-assembly, microfabrication or laser writing. The advantages of photonic hydrogel sensors over conventional assay formats include label-free, quantitative, reusable, and continuous measurement capability that can be integrated with equipment-free text or image display. This Review explains the operation principles of photonic hydrogel sensors, presents syntheses of stimuli-responsive polymers, and provides an overview of qualitative and quantitative readout technologies. Applications in clinical samples are discussed, and potential future directions are identified.

  2. Enhanced photon management in silicon thin film solar cells with different front and back interface texture

    NASA Astrophysics Data System (ADS)

    Tamang, Asman; Hongsingthong, Aswin; Jovanov, Vladislav; Sichanugrist, Porponth; Khan, Bakhtiar A.; Dewan, Rahul; Konagai, Makoto; Knipp, Dietmar

    2016-08-01

    Light trapping and photon management of silicon thin film solar cells can be improved by a separate optimization of the front and back contact textures. A separate optimization of the front and back contact textures is investigated by optical simulations taking realistic device geometries into consideration. The optical simulations are confirmed by experimentally realized 1 μm thick microcrystalline silicon solar cells. The different front and back contact textures lead to an enhancement of the short circuit current by 1.2 mA/cm2 resulting in a total short circuit current of 23.65 mA/cm2 and an energy conversion efficiency of 8.35%.

  3. Enhanced photon management in silicon thin film solar cells with different front and back interface texture.

    PubMed

    Tamang, Asman; Hongsingthong, Aswin; Jovanov, Vladislav; Sichanugrist, Porponth; Khan, Bakhtiar A; Dewan, Rahul; Konagai, Makoto; Knipp, Dietmar

    2016-01-01

    Light trapping and photon management of silicon thin film solar cells can be improved by a separate optimization of the front and back contact textures. A separate optimization of the front and back contact textures is investigated by optical simulations taking realistic device geometries into consideration. The optical simulations are confirmed by experimentally realized 1 μm thick microcrystalline silicon solar cells. The different front and back contact textures lead to an enhancement of the short circuit current by 1.2 mA/cm(2) resulting in a total short circuit current of 23.65 mA/cm(2) and an energy conversion efficiency of 8.35%. PMID:27481226

  4. Enhanced photon management in silicon thin film solar cells with different front and back interface texture

    PubMed Central

    Tamang, Asman; Hongsingthong, Aswin; Jovanov, Vladislav; Sichanugrist, Porponth; Khan, Bakhtiar A.; Dewan, Rahul; Konagai, Makoto; Knipp, Dietmar

    2016-01-01

    Light trapping and photon management of silicon thin film solar cells can be improved by a separate optimization of the front and back contact textures. A separate optimization of the front and back contact textures is investigated by optical simulations taking realistic device geometries into consideration. The optical simulations are confirmed by experimentally realized 1 μm thick microcrystalline silicon solar cells. The different front and back contact textures lead to an enhancement of the short circuit current by 1.2 mA/cm2 resulting in a total short circuit current of 23.65 mA/cm2 and an energy conversion efficiency of 8.35%. PMID:27481226

  5. Two-photon interference of temporally separated photons

    NASA Astrophysics Data System (ADS)

    Kim, Heonoh; Lee, Sang Min; Moon, Han Seb

    2016-10-01

    We present experimental demonstrations of two-photon interference involving temporally separated photons within two types of interferometers: a Mach-Zehnder interferometer and a polarization-based Michelson interferometer. The two-photon states are probabilistically prepared in a symmetrically superposed state within the two interferometer arms by introducing a large time delay between two input photons; this state is composed of two temporally separated photons, which are in two different or the same spatial modes. We then observe two-photon interference fringes involving both the Hong-Ou-Mandel interference effect and the interference of path-entangled two-photon states simultaneously in a single interferometric setup. The observed two-photon interference fringes provide simultaneous observation of the interferometric properties of the single-photon and two-photon wavepackets. The observations can also facilitate a more comprehensive understanding of the origins of the interference phenomena arising from spatially bunched/anti-bunched two-photon states comprised of two temporally separated photons within the interferometer arms.

  6. Two-photon interference of temporally separated photons

    PubMed Central

    Kim, Heonoh; Lee, Sang Min; Moon, Han Seb

    2016-01-01

    We present experimental demonstrations of two-photon interference involving temporally separated photons within two types of interferometers: a Mach-Zehnder interferometer and a polarization-based Michelson interferometer. The two-photon states are probabilistically prepared in a symmetrically superposed state within the two interferometer arms by introducing a large time delay between two input photons; this state is composed of two temporally separated photons, which are in two different or the same spatial modes. We then observe two-photon interference fringes involving both the Hong-Ou-Mandel interference effect and the interference of path-entangled two-photon states simultaneously in a single interferometric setup. The observed two-photon interference fringes provide simultaneous observation of the interferometric properties of the single-photon and two-photon wavepackets. The observations can also facilitate a more comprehensive understanding of the origins of the interference phenomena arising from spatially bunched/anti-bunched two-photon states comprised of two temporally separated photons within the interferometer arms. PMID:27708380

  7. Plasmonic enhancement in BiVO4 photonic crystals for efficient water splitting.

    PubMed

    Zhang, Liwu; Lin, Chia-Yu; Valev, Ventsislav K; Reisner, Erwin; Steiner, Ullrich; Baumberg, Jeremy J

    2014-10-15

    Photo-electrochemical water splitting is a very promising and environmentally friendly route for the conversion of solar energy into hydrogen. However, the solar-to-H2 conversion efficiency is still very low due to rapid bulk recombination of charge carriers. Here, a photonic nano-architecture is developed to improve charge carrier generation and separation by manipulating and confining light absorption in a visible-light-active photoanode constructed from BiVO4 photonic crystal and plasmonic nanostructures. Synergistic effects of photonic crystal stop bands and plasmonic absorption are observed to operate in this photonic nanostructure. Within the scaffold of an inverse opal photonic crystal, the surface plasmon resonance is significantly enhanced by the photonic Bragg resonance. Nanophotonic photoanodes show AM 1.5 photocurrent densities of 3.1 ± 0.1 mA cm(-2) at 1.23 V versus RHE, which is among the highest for oxide-based photoanodes and over 4 times higher than the unstructured planar photoanode.

  8. Ultra-weak photon emission from biological samples: definition, mechanisms, properties, detection and applications.

    PubMed

    Cifra, Michal; Pospíšil, Pavel

    2014-10-01

    This review attempts to summarize molecular mechanisms, spectral and intensity properties, detection techniques and applications of ultra-weak photon emission. Ultra-weak photon emission is the chemiluminescence from biological systems where electronically excited species are formed during oxidative metabolic or oxidative stress processes. It is generally accepted that photons are emitted (1) at near UVA, visible, and near IR spectral ranges from 350 to 1300nm and (2) at the intensity of photon emission in the range of several units to several hundreds (oxidative metabolic process) and several hundreds to several thousands (oxidative stress process) photons s(-1)cm(-2). Current development in detection using low-noise photomultiplier tubes and imaging using highly sensitive charge coupled device cameras allows temporal and spatial visualization of oxidative metabolic or oxidative stress processes, respectively. As the phenomenon of ultra-weak photon emission reflects oxidative metabolic or oxidative stress processes, it can be widely used as a non-invasive tool for monitoring of the physiological state of biological systems.

  9. Photons and magnetization

    NASA Astrophysics Data System (ADS)

    2013-06-01

    Magnets are often electrically activated, but recent research has demonstrated various schemes that can control magnetization using light and photocarriers. Nature Photonics spoke to Petr Němec and Tomas Jungwirth about their recent work on a polarization-independent optical-torque approach.

  10. Photon collider at TESLA

    NASA Astrophysics Data System (ADS)

    Telnov, Valery

    2001-10-01

    High energy photon colliders ( γγ, γe) based on backward Compton scattering of laser light is a very natural addition to e +e - linear colliders. In this report, we consider this option for the TESLA project. Recent study has shown that the horizontal emittance in the TESLA damping ring can be further decreased by a factor of four. In this case, the γγ luminosity in the high energy part of spectrum can reach about (1/3) Le +e -. Typical cross-sections of interesting processes in γγ collisions are higher than those in e +e - collisions by about one order of magnitude, so the number of events in γγ collisions will be more than that in e +e - collisions. Photon colliders can, certainly, give additional information and they are the best for the study of many phenomena. The main question is now the technical feasibility. The key new element in photon colliders is a very powerful laser system. An external optical cavity is a promising approach for the TESLA project. A free electron laser is another option. However, a more straightforward solution is "an optical storage ring (optical trap)" with a diode pumped solid state laser injector which is today technically feasible. This paper briefly reviews the status of a photon collider based on the linear collider TESLA, its possible parameters and existing problems.

  11. Auxiliary Entanglement in Photon Pairs for Multi-Photon Entanglement

    SciTech Connect

    Grice, Warren P; Bennink, Ryan S; Evans, Philip G; Humble, Travis S; Schaake, Jason

    2012-01-01

    A growing number of experiments make use of multiple pairs of photons generated in the process of spontaneous parametric down-conversion. We show that entanglement in unwanted degrees of freedom can adversely affect the results of these experiments. We also discuss techniques to reduce or eliminate spectral and spatial entanglement, and we present results from two-photon polarization-entangled source with almost no entanglement in these degrees of freedom. Finally, we present two methods for the generation of four-photon polarization- entangled states. In one of these methods, four-photon can be generated without the need for intermediate two-photon entanglement.

  12. Two-photon spectroscopy of excitons with entangled photons.

    PubMed

    Schlawin, Frank; Mukamel, Shaul

    2013-12-28

    The utility of quantum light as a spectroscopic tool is demonstrated for frequency-dispersed pump-probe, integrated pump-probe, and two-photon fluorescence signals which show Ramsey fringes. Simulations of the frequency-dispersed transmission of a broadband pulse of entangled photons interacting with a three-level model of matter reveal how the non-classical time-bandwidth properties of entangled photons can be used to disentangle congested spectra, and reveal otherwise unresolved features. Quantum light effects are most pronounced at weak intensities when entangled photon pairs are well separated, and are gradually diminished at higher intensities when different photon pairs overlap.

  13. Two-photon spectroscopy of excitons with entangled photons

    SciTech Connect

    Schlawin, Frank; Mukamel, Shaul

    2013-12-28

    The utility of quantum light as a spectroscopic tool is demonstrated for frequency-dispersed pump-probe, integrated pump-probe, and two-photon fluorescence signals which show Ramsey fringes. Simulations of the frequency-dispersed transmission of a broadband pulse of entangled photons interacting with a three-level model of matter reveal how the non-classical time-bandwidth properties of entangled photons can be used to disentangle congested spectra, and reveal otherwise unresolved features. Quantum light effects are most pronounced at weak intensities when entangled photon pairs are well separated, and are gradually diminished at higher intensities when different photon pairs overlap.

  14. Full Quantum Analysis of Two-Photon Absorption Using Two-Photon Wave Function: Comparison of Two-Photon Absorption with One-Photon Absorption

    NASA Astrophysics Data System (ADS)

    Nakanishi, Toshihiro; Kobayashi, Hirokazu; Sugiyama, Kazuhiko; Kitano, Masao

    2009-10-01

    For dissipation-free photon-photon interaction at the single photon level, we analyze one-photon and two-photon transitions induced by photon pairs in three-level atoms using two-photon wave functions. We show that two-photon absorption can be substantially enhanced by adjusting the time correlation of photon pairs. We study two typical cases: a Gaussian wave function and a rectangular wave function. In the latter, we find that under special conditions one-photon transition is completely suppressed, while two-photon transition is maintained with a high probability.

  15. Improved photon counting efficiency calibration using superconducting single photon detectors

    NASA Astrophysics Data System (ADS)

    Gan, Haiyong; Xu, Nan; Li, Jianwei; Sun, Ruoduan; Feng, Guojin; Wang, Yanfei; Ma, Chong; Lin, Yandong; Zhang, Labao; Kang, Lin; Chen, Jian; Wu, Peiheng

    2015-10-01

    The quantum efficiency of photon counters can be measured with standard uncertainty below 1% level using correlated photon pairs generated through spontaneous parametric down-conversion process. Normally a laser in UV, blue or green wavelength range with sufficient photon energy is applied to produce energy and momentum conserved photon pairs in two channels with desired wavelengths for calibration. One channel is used as the heralding trigger, and the other is used for the calibration of the detector under test. A superconducting nanowire single photon detector with advantages such as high photon counting speed (<20 MHz), low dark count rate (<50 counts per second), and wideband responsivity (UV to near infrared) is used as the trigger detector, enabling correlated photons calibration capabilities into shortwave visible range. For a 355nm single longitudinal mode pump laser, when a superconducting nanowire single photon detector is used as the trigger detector at 1064nm and 1560nm in the near infrared range, the photon counting efficiency calibration capabilities can be realized at 532nm and 460nm. The quantum efficiency measurement on photon counters such as photomultiplier tubes and avalanche photodiodes can be then further extended in a wide wavelength range (e.g. 400-1000nm) using a flat spectral photon flux source to meet the calibration demands in cutting edge low light applications such as time resolved fluorescence and nonlinear optical spectroscopy, super resolution microscopy, deep space observation, and so on.

  16. Photonic band gap materials

    NASA Astrophysics Data System (ADS)

    Cassagne, D.

    Photonic band gap materials Photonic band gap materials are periodic dielectric structures that control the propagation of electromagnetic waves. We describe the plane wave method, which allows to calculate the band structures of photonic crystals. By symmetry analysis and a perturbative approach, we predict the appearance of the low energy photonic band gaps of hexagonal structures. We propose new two-dimensional structures called graphite and boron nitride. Using a transfer matrix method, we calculate the transmission of the graphite structure and we show the crucial role of the coupling with external modes. We study the appearance of allowed modes in the photonic band gap by the introduction of localized defects in the periodicity. Finally, we discuss the properties of opals formed by self-organized silica microspheres, which are very promising for the fabrication of three-dimensional photonic crystals. Les matériaux à bandes interdites photoniques sont des structures diélectriques périodiques qui contrôlent la propagation des ondes électromagnétiques. Nous décrivons la méthode des ondes planes qui permet de calculer les structures de bandes des cristaux photoniques. Par une analyse de la symétrie et une approche perturbative, nous précisons les conditions d'existence des bandes interdites de basse énergie. Nous proposons de nouvelles structures bidimensionnelles appelées graphite et nitrure de bore. Grâce à une méthode de matrices de transfert, nous calculons la transmission de la structure graphite et nous mettons en évidence le rôle fondamental du couplage avec les modes extérieurs. Nous étudions l'apparition de modes permis dans la bande interdite grâce à l'introduction de défauts dans la périodicité. Enfin, nous discutons les propriétés des opales constituées de micro-billes de silice auto-organisées, qui sont très prometteuses pour la fabrication de cristaux photoniques tridimensionnels.

  17. Photon + jets at D0

    SciTech Connect

    Sonnenschein, Lars; /RWTH Aachen U.

    2009-06-01

    Photon plus jet production has been studied by the D0 experiment in Run II of the Fermilab Tevatron Collider at a centre of mass energy of {radical}s = 1.96 TeV. Measurements of the inclusive photon, inclusive photon plus jet, photon plus heavy flavour jet cross sections and double parton interactions in photon plus three jet events are presented. They are based on integrated luminosities between 0.4 fb{sup -1} and 1.0 fb{sup -1}. The results are compared to perturbative QCD calculations in various approximations.

  18. Photonic-powered cable assembly

    DOEpatents

    Sanderson, Stephen N; Appel, Titus James; Wrye, IV, Walter C

    2014-06-24

    A photonic-cable assembly includes a power source cable connector ("PSCC") coupled to a power receive cable connector ("PRCC") via a fiber cable. The PSCC electrically connects to a first electronic device and houses a photonic power source and an optical data transmitter. The fiber cable includes an optical transmit data path coupled to the optical data transmitter, an optical power path coupled to the photonic power source, and an optical feedback path coupled to provide feedback control to the photonic power source. The PRCC electrically connects to a second electronic device and houses an optical data receiver coupled to the optical transmit data path, a feedback controller coupled to the optical feedback path to control the photonic power source, and a photonic power converter coupled to the optical power path to convert photonic energy received over the optical power path to electrical energy to power components of the PRCC.

  19. Photonic-powered cable assembly

    DOEpatents

    Sanderson, Stephen N.; Appel, Titus James; Wrye, IV, Walter C.

    2013-01-22

    A photonic-cable assembly includes a power source cable connector ("PSCC") coupled to a power receive cable connector ("PRCC") via a fiber cable. The PSCC electrically connects to a first electronic device and houses a photonic power source and an optical data transmitter. The fiber cable includes an optical transmit data path coupled to the optical data transmitter, an optical power path coupled to the photonic power source, and an optical feedback path coupled to provide feedback control to the photonic power source. The PRCC electrically connects to a second electronic device and houses an optical data receiver coupled to the optical transmit data path, a feedback controller coupled to the optical feedback path to control the photonic power source, and a photonic power converter coupled to the optical power path to convert photonic energy received over the optical power path to electrical energy to power components of the PRCC.

  20. Natural photonic crystals

    NASA Astrophysics Data System (ADS)

    Vigneron, Jean Pol; Simonis, Priscilla

    2012-10-01

    Photonic structures appeared in nature several hundred millions years ago. In the living world, color is used for communication and this important function strongly impacts the individual chances of survival as well as the chances to reproduce. This has a statistical influence on species populations. Therefore, because they are involved in evolution, natural color-generating structures are - from some point of view - highly optimized. In this short review, a survey is presented of the development of natural photonic crystal-type structures occurring in insects, spiders, birds, fishes and other marine animals, in plants and more, from the standpoint of light-waves propagation. One-, two-, and three-dimensional structures will be reviewed with selected examples.

  1. PHOTON: A user's manual

    SciTech Connect

    Chapman, D.

    1988-01-01

    PHOTON has proven very useful in the development of the X17 superconducting wiggler beamline. Its use has determined the shielding required from the wiggler device to the very end of the beamline in the hutches and angiography section. Doses calculated by this program have been compared with experimental results from conventional bending magnet beamline with great success. In each case the program consistently overestimated the dose by factors ranging from 2 to 10. The reason for this overestimation is understood and was not refined further in the program in order to maintain some level of safety in the shielding calculations. PHOTON should prove useful in the design of any beamline. Its ability to calculate power deposited and spectra transmitted through nearly arbitrary beamline configurations as well as the scattered radiation doses through shielding walls make it a very powerful tool.

  2. Photons in a ball

    NASA Astrophysics Data System (ADS)

    Mück, Wolfgang

    2015-12-01

    The electromagnetic field inside a spherical cavity of large radius R is considered in the presence of stationary charge and current densities. R provides infra-red regularisation while maintaining gauge invariance. The quantum ground state of physical photons forming the magnetic field is found to be a coherent state with a definite mean occupation number. The electric field, which is determined by the Gauss law constraint, is maintained by a minimum uncertainty coherent state, according to the projection operator approach to the quantisation of constrained systems. The mean occupation number of this state is proportional to the square of the total charge. The results confirm formulae obtained previously from a calculation with a finite photon mass for infra-red regularisation.

  3. Optics of photonic quasicrystals

    NASA Astrophysics Data System (ADS)

    Vardeny, Z. Valy; Nahata, Ajay; Agrawal, Amit

    2013-03-01

    The physics of periodic systems are of fundamental importance and result in various phenomena that govern wave transport and interference. However, deviations from periodicity may result in higher complexity and give rise to a number of surprising effects. One such deviation can be found in the field of optics in the realization of photonic quasicrystals, a class of structures made from building blocks that are arranged using well-designed patterns but lack translational symmetry. Nevertheless, these structures, which lie between periodic and disordered structures, still show sharp diffraction patterns that confirm the existence of wave interference resulting from their long-range order. In this Review, we discuss the beautiful physics unravelled in photonic quasicrystals of one, two and three dimensions, and describe how they can influence optical transmission and reflectivity, photoluminescence, light transport, plasmonics and laser action.

  4. Surface nanoscale axial photonics.

    PubMed

    Sumetsky, M; Fini, J M

    2011-12-19

    Dense photonic integration promises to revolutionize optical computing and communications. However, efforts towards this goal face unacceptable attenuation of light caused by surface roughness in microscopic devices. Here we address this problem by introducing Surface Nanoscale Axial Photonics (SNAP). The SNAP platform is based on whispering gallery modes circulating around the optical fiber surface and undergoing slow axial propagation readily described by the one-dimensional Schrödinger equation. These modes can be steered with dramatically small nanoscale variation of the fiber radius, which is quite simple to introduce in practice. Extremely low loss of SNAP devices is achieved due to the low surface roughness inherent in a drawn fiber surface. In excellent agreement with the developed theory, we experimentally demonstrate localization of light in quantum wells, halting light by a point source, tunneling through potential barriers, dark states, etc. This demonstration has intriguing potential applications in filtering, switching, slowing light, and sensing.

  5. Photon activation therapy.

    PubMed

    Fairchild, R G; Bond, V P

    1984-12-01

    It is suggested here that significant advantages should accrue from the use of 40 keV photons from implanted sources of 145Sm. These energies should stimulate Auger electron cascades from IdUrd, as well as produce non-repairable damage from radiosensitization. The use of low dose rates (approximately 10 rd/hr) should allow repair in normal tissues exposed to the activating photons. Utilization of this technique with brain tumors should minimize problems associated with radiosensitization of normal tissues, as CNS tissues do not synthesize DNA. The deposition of high LET radiations selectively in tumor cells provides unique advantages not available to either conventional therapy or other forms of particle therapy (fast neutrons, protons, pions, heavy ions). PMID:6515666

  6. Photonics for accelerator instrumentation

    SciTech Connect

    Stillman, A.

    1993-12-31

    Nonlinear optical effects in certain types of crystals have the capacity to improve the performance of sampling circuits by a large margin. The theory on nonlinear optics and the associated devices is rather straightforward. I will present some of the relevant ideas and illustrate how these principles can result in order of magnitude improvements in sampling circuits. As an example of the photonic technique, I will illustrate how to design a beam position monitor that uses a nonlinear crystal.

  7. Photon-neutrino interactions

    SciTech Connect

    Dicus, D.A.; Repko, W.W.

    1997-12-01

    The cross sections for the processes {gamma}{nu} {yields} {gamma}{gamma} {yields} {nu}{anti {nu}} are calculated with the aid of an effective Lagrangian derived from the Standard model. These cross sections are shown to be much larger than the elastic cross section {sigma}({gamma}{nu} {yields} {gamma}{nu}) for photon energies {omega} {ge} 1 keV. Possible astrophysical implications are discussed.

  8. Photonic crystal optical memory

    NASA Astrophysics Data System (ADS)

    Lima, A. Wirth; Sombra, A. S. B.

    2011-06-01

    After several decades pushing the technology and the development of the world, the electronics is giving space for technologies that use light. We propose and analyze an optical memory embedded in a nonlinear photonic crystal (PhC), whose system of writing and reading data is controlled by an external command signal. This optical memory is based on optical directional couplers connected to a shared optical ring. Such a device can work over the C-Band of ITU (International Telecommunication Union).

  9. Imaging by photon counting with 256x256 pixel matrix

    NASA Astrophysics Data System (ADS)

    Tlustos, Lukas; Campbell, Michael; Heijne, Erik H. M.; Llopart, Xavier

    2004-09-01

    Using 0.25µm standard CMOS we have developed 2-D semiconductor matrix detectors with sophisticated functionality integrated inside each pixel of a hybrid sensor module. One of these sensor modules is a matrix of 256x256 square 55µm pixels intended for X-ray imaging. This device is called 'Medipix2' and features a fast amplifier and two-level discrimination for signals between 1000 and 100000 equivalent electrons, with overall signal noise ~150 e- rms. Signal polarity and comparator thresholds are programmable. A maximum count rate of nearly 1 MHz per pixel can be achieved, which corresponds to an average flux of 3x10exp10 photons per cm2. The selected signals can be accumulated in each pixel in a 13-bit register. The serial readout takes 5-10 ms. A parallel readout of ~300 µs could also be used. Housekeeping functions such as local dark current compensation, test pulse generation, silencing of noisy pixels and threshold tuning in each pixel contribute to the homogeneous response over a large sensor area. The sensor material can be adapted to the energy of the X-rays. Best results have been obtained with high-resistivity silicon detectors, but also CdTe and GaAs detectors have been used. The lowest detectable X-ray energy was about 4 keV. Background measurements have been made, as well as measurements of the uniformity of imaging by photon counting. Very low photon count rates are feasible and noise-free at room temperature. The readout matrix can be used also with visible photons if an energy or charge intensifier structure is interposed such as a gaseous amplification layer or a microchannel plate or acceleration field in vacuum.

  10. Photonics Explorer Workshop

    NASA Astrophysics Data System (ADS)

    Prasad, Amrita; Debaes, Nathalie

    2014-07-01

    The Photonics Explorer is an intra-curricular educational kit developed in a European project with a pan-European collaboration of over 35 teachers and science education professors. Unlike conventional educational outreach kits, the Photonics Explorer is specifically designed to integrate seamlessly in school curricula and enhance and complement the teaching and learning of science and optics in the classroom. The kit equips teachers with class sets of experimental components, provided within a supporting didactic framework and is designed for lower and upper secondary students (12-18 years). The kit is provided completely free of charge to teachers in conjunction with teacher training courses. The workshop will provide an overview of the Photonics Explorer intra-curricular kit and give teachers the opportunity to work hands-on with the material and didactic content of two modules, `Light Signals' (lower secondary) and `Diffraction and Interference'(upper secondary). We also aim to receive feedback regarding the content, components and didactic framework from teachers from non- European countries, to understand the relevance of the kit for their teaching and the ability for such a kit to integrate into non-EU curricula.

  11. Photon-activation therapy

    SciTech Connect

    Fairchild, R.G.; Bond, V.P.

    1982-01-01

    Photon Activation Therapy (PAT) is a technique in which radiation dose to tumor is enhanced via introduction of stable /sup 127/I in the form of iodinated deoxyuridine (IdUrd). Stimulation of cytotoxic effects from IdUrd is accomplished by activation with external (or implanted) radiation sources. Thus, accumulations of this nucleoside in actively competing cellpools do not preclude therapy in so far as such tissues can be excluded from the radiation field. Calculations show that 5% replacement of thymidine (Tyd) in tumor DNA should enhance the biological effectiveness of a given photon radiotherapy dose by a factor of approx. 3. Proportionally higher gains would result from higher replacements of Tyd and IdUrd. In addition, biological response is enhanced by chemical sensitization with IdUrd. The data indicate that damage from photon activation as well as chemical sensitization does not repair. Thus, at low dose rates, a further increase in therapeutic gain should accrue as normal tissues are allowed to repair and regenerate. A samarium-145 source has been developed for PAT, with activating x-ray energies of from 38 to 45 keV. Favorable clinical results can be expected through the use of IdUrd and protracted irradiations with low energy x-rays. In particular, PAT may provide unique advantages at selected sites such as brain, or head and neck tumors. (ERB)

  12. Slotted Photonic Crystal Sensors

    PubMed Central

    Scullion, Mark G.; Krauss, Thomas F.; Di Falco, Andrea

    2013-01-01

    Optical biosensors are increasingly being considered for lab-on-a-chip applications due to their benefits such as small size, biocompatibility, passive behaviour and lack of the need for fluorescent labels. The light guiding mechanisms used by many of them results in poor overlap of the optical field with the target molecules, reducing the maximum sensitivity achievable. This review article presents a new platform for optical biosensors, namely slotted photonic crystals, which provide higher sensitivities due to their ability to confine, spatially and temporally, the optical mode peak within the analyte itself. Loss measurements showed values comparable to standard photonic crystals, confirming their ability to be used in real devices. A novel resonant coupler was designed, simulated, and experimentally tested, and was found to perform better than other solutions within the literature. Combining with cavities, microfluidics and biological functionalization allowed proof-of-principle demonstrations of protein binding to be carried out. Higher sensitivities were observed in smaller structures than possible with most competing devices reported in the literature. This body of work presents slotted photonic crystals as a realistic platform for complete on-chip biosensing; addressing key design, performance and application issues, whilst also opening up exciting new ideas for future study. PMID:23503295

  13. Slotted photonic crystal sensors.

    PubMed

    Scullion, Mark G; Krauss, Thomas F; Di Falco, Andrea

    2013-01-01

    Optical biosensors are increasingly being considered for lab-on-a-chip applications due to their benefits such as small size, biocompatibility, passive behaviour and lack of the need for fluorescent labels. The light guiding mechanisms used by many of them results in poor overlap of the optical field with the target molecules, reducing the maximum sensitivity achievable. This review article presents a new platform for optical biosensors, namely slotted photonic crystals, which provide higher sensitivities due to their ability to confine, spatially and temporally, the optical mode peak within the analyte itself. Loss measurements showed values comparable to standard photonic crystals, confirming their ability to be used in real devices. A novel resonant coupler was designed, simulated, and experimentally tested, and was found to perform better than other solutions within the literature. Combining with cavities, microfluidics and biological functionalization allowed proof-of-principle demonstrations of protein binding to be carried out. Higher sensitivities were observed in smaller structures than possible with most competing devices reported in the literature. This body of work presents slotted photonic crystals as a realistic platform for complete on-chip biosensing; addressing key design, performance and application issues, whilst also opening up exciting new ideas for future study. PMID:23503295

  14. Super Photon Counters

    NASA Technical Reports Server (NTRS)

    Mather, John

    1999-01-01

    The perfect photon detector would measure the arrival time, the energy, the polarization, and the position of every arriving quantum, but that is easier said than done. Two groups have now succeeded in doing time-resolved spectroscopy on the Crab Nebula pulsar, measuring everything but the polarization, with reports from Romani et al. at Stanford and from Perryman et al. at ESTEC. Both groups use superconducting detectors to gain the necessary speed and sensitivity. The photon can heat the electrons in a superconductor biased in the middle of its resistive transition, or break bound superconducting electron-hole pairs, which can then be collected. Three years ago, Peacock et al. reported that they had detected single optical photons with a superconducting tunnel junction (STJ), and Paresce wrote a News and Views article. A tunnel junction uses two pieces of conductive material, separated by a tiny gap of insulating material or even vacuum. If the gap is thin enough, electrons can tunnel across anyway, and if the conductors are superconductors, the junction displays very useful quantum mechanical properties and electrical nonlinearities. Amplifiers, detectors, oscillators, and computer circuits can all be made from them. Their special advantage is that they operate at very low temperatures, dissipate very little power, operate very fast, and are very small.

  15. Integrated photonic quantum walks

    NASA Astrophysics Data System (ADS)

    Gräfe, Markus; Heilmann, René; Lebugle, Maxime; Guzman-Silva, Diego; Perez-Leija, Armando; Szameit, Alexander

    2016-10-01

    Over the last 20 years quantum walks (QWs) have gained increasing interest in the field of quantum information science and processing. In contrast to classical walkers, quantum objects exhibit intrinsic properties like non-locality and non-classical many-particle correlations, which renders QWs a versatile tool for quantum simulation and computation as well as for a deeper understanding of genuine quantum mechanics. Since they are highly controllable and hardly interact with their environment, photons seem to be ideally suited quantum walkers. In order to study and exploit photonic QWs, lattice structures that allow low loss coherent evolution of quantum states are demanded. Such requirements are perfectly met by integrated optical waveguide devices that additionally allow a substantial miniaturization of experimental settings. Moreover, by utilizing the femtosecond direct laser writing technique three-dimensional waveguide structures are capable of analyzing QWs also on higher dimensional geometries. In this context, advances and findings of photonic QWs are discussed in this review. Various concepts and experimental results are presented covering, such as different quantum transport regimes, the Boson sampling problem, and the discrete fractional quantum Fourier transform.

  16. Photonic Molecule Lasers Revisited

    NASA Astrophysics Data System (ADS)

    Gagnon, Denis; Dumont, Joey; Déziel, Jean-Luc; Dubé, Louis J.

    2014-05-01

    Photonic molecules (PMs) formed by coupling two or more optical resonators are ideal candidates for the fabrication of integrated microlasers, photonic molecule lasers. Whereas most calculations on PM lasers have been based on cold-cavity (passive) modes, i.e. quasi-bound states, a recently formulated steady-state ab initio laser theory (SALT) offers the possibility to take into account the spectral properties of the underlying gain transition, its position and linewidth, as well as incorporating an arbitrary pump profile. We will combine two theoretical approaches to characterize the lasing properties of PM lasers: for two-dimensional systems, the generalized Lorenz-Mie theory will obtain the resonant modes of the coupled molecules in an active medium described by SALT. Not only is then the theoretical description more complete, the use of an active medium provides additional parameters to control, engineer and harness the lasing properties of PM lasers for ultra-low threshold and directional single-mode emission. We will extend our recent study and present new results for a number of promising geometries. The authors acknowledge financial support from NSERC (Canada) and the CERC in Photonic Innovations of Y. Messaddeq.

  17. Nonlocal Structures: Bilocal Photon

    NASA Astrophysics Data System (ADS)

    Clapp, Roger E.

    1980-01-01

    As a starting point, it is postulated that all particles and fields are built from a single primitive field, which must then be a massless fermion with a σ spin of one-half. Two helicities are embodied in a τ spin of one-half. The vacuum is an open Fermi sea whose height is a wave number κ. Elementary particles are structures having the form of standing-wave systems floating on the vacuum sea, with the height κ providing both the scale of inner structural size and the mass unit for the elementary particle mass spectrum. A bilocal photon starts with a function describing two primitive quanta with parallel σ spin and opposite τ spin. A centroid-time wave equation then couples-in an infinite set of orthogonal functions. The introduction of an operator Q λ permits the reduction of the infinite secular determinant to a finite six-by-six determinant. Solutions (for the infinite expansion) are obtained describing photons with right-handed and left-handed polarizations. Superpositions of these give linearly polarized photons. Electric and magnetic field vectors, satisfying the vacuum Maxwell equations, are obtained from a bilocal Hertz vector given by п= (2/κ3 c)(∂/∂ t r)∇rΨ(1,2), where Ψ(1,2) is the bilocal wave function, and tr and r are the relative time and relative position variables.

  18. X-ray Photon Counting and Two-Color X-ray Imaging Using Indirect Detection

    PubMed Central

    Dierickx, Bart; Yao, Qiang; Witvrouwen, Nick; Uwaerts, Dirk; Vandewiele, Stijn; Gao, Peng

    2016-01-01

    In this paper, we report on the design and performance of a 1 cm2, 90 × 92-pixel image sensor. It is made X-ray sensitive by the use of a scintillator. Its pixels have a charge packet counting circuit topology with two channels, each realizing a different charge packet size threshold and analog domain event counting. Here, the sensor’s performance was measured in setups representative of a medical X-ray environment. Further, two-energy-level photon counting performance is demonstrated, and its capabilities and limitations are documented. We then provide an outlook on future improvements. PMID:27240362

  19. Metallophthalocyanines as triplet sensitizers for highly efficient photon upconversion based on sensitized triplet-triplet annihilation.

    PubMed

    Han, J L; You, J; Yonemura, H; Yamada, S; Wang, S R; Li, X G

    2016-08-01

    Soluble palladium and platinum phthalocyanines with coumarin moieties were synthesized with Q bands in the red and near-IR regions, in which the molar extinction coefficients were up to 1.01 × 10(5) cm(-1) mol(-1). These metallophthalocyanines were coupled with rubrene and applied in photon upconversion systems based on triplet-triplet annihilation. The highest upconversion efficiency of the palladium phthalocyanine was 5.6%, which is higher than that of the platinum phthalocyanine-rubrene system. The larger molar extinction coefficient resulted in high upconversion capability (>10(5) cm(-1) mol(-1)) and low saturation incident power (<20 mW cm(-2)). PMID:27431880

  20. Setting the jet energy scale in the CMS calorimeter using events with direct photons

    NASA Astrophysics Data System (ADS)

    Golutvin, I. A.; Zarubin, A. V.; Kodolova, O. L.; Konoplyanikov, V. F.; Ul'Yanov, A. L.; Shmatov, S. V.

    2008-09-01

    The procedure of setting the jet energy using events with direct photons proposed as one of the methods of jet calibration in the CMS is studied. Based on complete simulation of events in the CMS including the effects of pile-up of additional events for the initial beam luminosity of the accelerator ( L = 2 × 1033 cm-2s-1), the rules for event selection during calibration are proposed. Errors of the proposed method due to the background and the radiation in the ISRare estimated.

  1. Topological Photonic States

    NASA Astrophysics Data System (ADS)

    He, Cheng; Lin, Liang; Sun, Xiao-Chen; Liu, Xiao-Ping; Lu, Ming-Hui; Chen, Yan-Feng

    2014-01-01

    As exotic phenomena in optics, topological states in photonic crystals have drawn much attention due to their fundamental significance and great potential applications. Because of the broken time-reversal symmetry under the influence of an external magnetic field, the photonic crystals composed of magneto-optical materials will lead to the degeneracy lifting and show particular topological characters of energy bands. The upper and lower bulk bands have nonzero integer topological numbers. The gapless edge states can be realized to connect two bulk states. This topological photonic states originated from the topological property can be analogous to the integer quantum Hall effect in an electronic system. The gapless edge state only possesses a single sign of gradient in the whole Brillouin zone, and thus the group velocity is only in one direction leading to the one-way energy flow, which is robust to disorder and impurity due to the nontrivial topological nature of the corresponding electromagnetic states. Furthermore, this one-way edge state would cross the Brillouin center with nonzero group velocity, where the negative-zero-positive phase velocity can be used to realize some interesting phenomena such as tunneling and backward phase propagation. On the other hand, under the protection of time-reversal symmetry, a pair of gapless edge states can also be constructed by using magnetic-electric coupling meta-materials, exhibiting Fermion-like spin helix topological edge states, which can be regarded as an optical counterpart of topological insulator originating from the spin-orbit coupling. The aim of this article is to have a comprehensive review of recent research literatures published in this emerging field of photonic topological phenomena. Photonic topological states and their related phenomena are presented and analyzed, including the chiral edge states, polarization dependent transportation, unidirectional waveguide and nonreciprocal optical transmission, all

  2. Amorphous nanostructuralization in HOPG by 1014 W cm-2 laser

    NASA Astrophysics Data System (ADS)

    NISHIMURA, Yasuhiko; KITAGAWA, Yoneyoshi; MORI, Yoshitaka; ISHII, Katsuhiro; HANAYAMA, Ryohei; AZUMA, Hirozumi; HIOKI, Tatsumi; NISHI, Teppei; MOTOHIRO, Tomoyoshi; KOMEDA, Osamu; SEKINE, Takashi; SATO, Nakahiro; KURITA, Takashi; KAWASHIMA, Toshiyuki; KAN, Hirofumi; SUNAHARA, Atsushi; SENTOKU, Yasuhiko; MIURA, Eisuke

    2016-05-01

    This reports provide an amorphous nanostructuralization technique on the surface modification in Highly Oriented Pyrolytic Graphite (HOPG) by using a femtosecond laser. We showed, for the first time, that the surface of HOPG is changed to the amorphous nanostructuralization graphite by using a femtosecond laser-driven compression technique. Our results also suggest that the HOPG surface is changed until the deeper area from the surface by the laser-driven shock wave. A single shot of a femtosecond laser beam (1.27 ∼ 1.33×1014 Wcm∼2 in intensity, with 2 mm-diameter, and 110 fs in pulse width) is irradiated under the vacuum ambience onto a 2 mm-thick of HOPG. The calculated impact pressures on a sample was 8.3 ∼ 8.7 GPa. Crystal structure in the HOPG were analyzed using a Raman spectroscopy and an X-ray diffraction, those analyzing depth from the surface were 50 nm and 350 μm, respectively.

  3. Synthetic Landau levels for photons.

    PubMed

    Schine, Nathan; Ryou, Albert; Gromov, Andrey; Sommer, Ariel; Simon, Jonathan

    2016-06-30

    Synthetic photonic materials are an emerging platform for exploring the interface between microscopic quantum dynamics and macroscopic material properties. Photons experiencing a Lorentz force develop handedness, providing opportunities to study quantum Hall physics and topological quantum science. Here we present an experimental realization of a magnetic field for continuum photons. We trap optical photons in a multimode ring resonator to make a two-dimensional gas of massive bosons, and then employ a non-planar geometry to induce an image rotation on each round-trip. This results in photonic Coriolis/Lorentz and centrifugal forces and so realizes the Fock–Darwin Hamiltonian for photons in a magnetic field and harmonic trap. Using spatial- and energy-resolved spectroscopy, we track the resulting photonic eigenstates as radial trapping is reduced, finally observing a photonic Landau level at degeneracy. To circumvent the challenge of trap instability at the centrifugal limit, we constrain the photons to move on a cone. Spectroscopic probes demonstrate flat space (zero curvature) away from the cone tip. At the cone tip, we observe that spatial curvature increases the local density of states, and we measure fractional state number excess consistent with the Wen–Zee theory, providing an experimental test of this theory of electrons in both a magnetic field and curved space. This work opens the door to exploration of the interplay of geometry and topology, and in conjunction with Rydberg electromagnetically induced transparency, enables studies of photonic fractional quantum Hall fluids and direct detection of anyons.

  4. Synthetic Landau levels for photons

    NASA Astrophysics Data System (ADS)

    Schine, Nathan; Ryou, Albert; Gromov, Andrey; Sommer, Ariel; Simon, Jonathan

    2016-06-01

    Synthetic photonic materials are an emerging platform for exploring the interface between microscopic quantum dynamics and macroscopic material properties. Photons experiencing a Lorentz force develop handedness, providing opportunities to study quantum Hall physics and topological quantum science. Here we present an experimental realization of a magnetic field for continuum photons. We trap optical photons in a multimode ring resonator to make a two-dimensional gas of massive bosons, and then employ a non-planar geometry to induce an image rotation on each round-trip. This results in photonic Coriolis/Lorentz and centrifugal forces and so realizes the Fock–Darwin Hamiltonian for photons in a magnetic field and harmonic trap. Using spatial- and energy-resolved spectroscopy, we track the resulting photonic eigenstates as radial trapping is reduced, finally observing a photonic Landau level at degeneracy. To circumvent the challenge of trap instability at the centrifugal limit, we constrain the photons to move on a cone. Spectroscopic probes demonstrate flat space (zero curvature) away from the cone tip. At the cone tip, we observe that spatial curvature increases the local density of states, and we measure fractional state number excess consistent with the Wen–Zee theory, providing an experimental test of this theory of electrons in both a magnetic field and curved space. This work opens the door to exploration of the interplay of geometry and topology, and in conjunction with Rydberg electromagnetically induced transparency, enables studies of photonic fractional quantum Hall fluids and direct detection of anyons.

  5. Synthetic Landau levels for photons

    NASA Astrophysics Data System (ADS)

    Schine, Nathan; Ryou, Albert; Gromov, Andrey; Sommer, Ariel; Simon, Jonathan

    2016-06-01

    Synthetic photonic materials are an emerging platform for exploring the interface between microscopic quantum dynamics and macroscopic material properties. Photons experiencing a Lorentz force develop handedness, providing opportunities to study quantum Hall physics and topological quantum science. Here we present an experimental realization of a magnetic field for continuum photons. We trap optical photons in a multimode ring resonator to make a two-dimensional gas of massive bosons, and then employ a non-planar geometry to induce an image rotation on each round-trip. This results in photonic Coriolis/Lorentz and centrifugal forces and so realizes the Fock-Darwin Hamiltonian for photons in a magnetic field and harmonic trap. Using spatial- and energy-resolved spectroscopy, we track the resulting photonic eigenstates as radial trapping is reduced, finally observing a photonic Landau level at degeneracy. To circumvent the challenge of trap instability at the centrifugal limit, we constrain the photons to move on a cone. Spectroscopic probes demonstrate flat space (zero curvature) away from the cone tip. At the cone tip, we observe that spatial curvature increases the local density of states, and we measure fractional state number excess consistent with the Wen-Zee theory, providing an experimental test of this theory of electrons in both a magnetic field and curved space. This work opens the door to exploration of the interplay of geometry and topology, and in conjunction with Rydberg electromagnetically induced transparency, enables studies of photonic fractional quantum Hall fluids and direct detection of anyons.

  6. Synthetic Landau levels for photons.

    PubMed

    Schine, Nathan; Ryou, Albert; Gromov, Andrey; Sommer, Ariel; Simon, Jonathan

    2016-06-30

    Synthetic photonic materials are an emerging platform for exploring the interface between microscopic quantum dynamics and macroscopic material properties. Photons experiencing a Lorentz force develop handedness, providing opportunities to study quantum Hall physics and topological quantum science. Here we present an experimental realization of a magnetic field for continuum photons. We trap optical photons in a multimode ring resonator to make a two-dimensional gas of massive bosons, and then employ a non-planar geometry to induce an image rotation on each round-trip. This results in photonic Coriolis/Lorentz and centrifugal forces and so realizes the Fock–Darwin Hamiltonian for photons in a magnetic field and harmonic trap. Using spatial- and energy-resolved spectroscopy, we track the resulting photonic eigenstates as radial trapping is reduced, finally observing a photonic Landau level at degeneracy. To circumvent the challenge of trap instability at the centrifugal limit, we constrain the photons to move on a cone. Spectroscopic probes demonstrate flat space (zero curvature) away from the cone tip. At the cone tip, we observe that spatial curvature increases the local density of states, and we measure fractional state number excess consistent with the Wen–Zee theory, providing an experimental test of this theory of electrons in both a magnetic field and curved space. This work opens the door to exploration of the interplay of geometry and topology, and in conjunction with Rydberg electromagnetically induced transparency, enables studies of photonic fractional quantum Hall fluids and direct detection of anyons. PMID:27281214

  7. Optics of globular photonic crystals

    SciTech Connect

    Gorelik, V S

    2007-05-31

    The results of experimental and theoretical studies of the optical properties of globular photonic crystals - new physical objects having a crystal structure with the lattice period exceeding considerably the atomic size, are presented. As globular photonic crystals, artificial opal matrices consisting of close-packed silica globules of diameter {approx}200 nm were used. The reflection spectra of these objects characterising the parameters of photonic bands existing in these crystals in the visible spectral region are presented. The idealised models of the energy band structure of photonic crystals investigated in the review give analytic dispersion dependences for the group velocity and the effective photon mass in a globular photonic crystal. The characteristics of secondary emission excited in globular photonic crystals by monochromatic and broadband radiation are presented. The results of investigations of single-photon-excited delayed scattering of light observed in globular photonic crystals exposed to cw UV radiation and radiation from a repetitively pulsed copper vapour laser are presented. The possibilities of using globular photonic crystals as active media for lasing in different spectral regions are considered. It is proposed to use globular photonic crystals as sensitive sensors in optoelectronic devices for molecular analysis of organic and inorganic materials by the modern methods of laser spectroscopy. The results of experimental studies of spontaneous and stimulated globular scattering of light are discussed. The conditions for observing resonance and two-photon-excited delayed scattering of light are found. The possibility of accumulation and localisation of the laser radiation energy inside a globular photonic crystal is reported. (review)

  8. Air surface microdischarge-photon synergy in antibacterial plasma-activated water

    NASA Astrophysics Data System (ADS)

    Graves, David; Pavlovich, Mathew; Chang, Hung-Wen; Sakiyama, Yuki; Clark, Douglas

    2013-09-01

    We show that the antibacterial effects of air plasma on water can be amplified by synergy with ultraviolet (UV) photons. We use the surface microdischarge configuration (SMD) in atmospheric air adjacent to bacteria-laden water coupled with UVA (360 nm) photons from a light emitting diode (LED) to demonstrate this synergy. Air SMD, especially if operated in a confined space, can operate in different modes: low power mode (<0.1 W/cm2) generates primarily O3 whereas higher powers generate mainly nitrogen oxides; we focus here on the latter. The nitrogen oxide mode creates a powerful antibacterial mixture in water, including NO2-, NO3- and H2O2. Although these species alone can be strongly antibacterial, especially at low pH, we show that addition of UVA photons greatly amplifies the antibacterial effect. We first measured log reductions with only photons and then only plasma. Only when UVA exposes water after plasma does the synergy appear. Synergy appears to be due to UVA photolysis of plasma-generated NO2- to form NO and OH. We conclude that combining plasma-generated chemical species with activating photons can amplify and strengthen plasma effectiveness in many biological and other applications. Supported by Department of Energy, Office of Fusion Science Plasma Science Center.

  9. Tunable photonic Bloch oscillations in electrically modulated photonic crystals.

    PubMed

    Wang, Gang; Huang, Ji Ping; Yu, Kin Wah

    2008-10-01

    We exploit theoretically the occurrence and tunability of photonic Bloch oscillations (PBOs) in one-dimensional photonic crystals (PCs) containing nonlinear composites. Because of the enhanced third-order nonlinearity (Kerr-type nonlinearity) of composites, photons undergo oscillations inside tilted photonic bands, which are achieved by the application of graded external-pump electric fields on such PCs, varying along the direction perpendicular to the surface of layers. The tunability of PBOs (including amplitude and period) is readily achieved by changing the field gradient. With an appropriate graded pump ac or dc electric field, terahertz PBOs can appear and cover a terahertz band in an electromagnetic spectrum.

  10. Resonant photonic States in coupled heterostructure photonic crystal waveguides.

    PubMed

    Cox, Jd; Sabarinathan, J; Singh, Mr

    2010-01-01

    In this paper, we study the photonic resonance states and transmission spectra of coupled waveguides made from heterostructure photonic crystals. We consider photonic crystal waveguides made from three photonic crystals A, B and C, where the waveguide heterostructure is denoted as B/A/C/A/B. Due to the band structure engineering, light is confined within crystal A, which thus act as waveguides. Here, photonic crystal C is taken as a nonlinear photonic crystal, which has a band gap that may be modified by applying a pump laser. We have found that the number of bound states within the waveguides depends on the width and well depth of photonic crystal A. It has also been found that when both waveguides are far away from each other, the energies of bound photons in each of the waveguides are degenerate. However, when they are brought close to each other, the degeneracy of the bound states is removed due to the coupling between them, which causes these states to split into pairs. We have also investigated the effect of the pump field on photonic crystal C. We have shown that by applying a pump field, the system may be switched between a double waveguide to a single waveguide, which effectively turns on or off the coupling between degenerate states. This reveals interesting results that can be applied to develop new types of nanophotonic devices such as nano-switches and nano-transistors.

  11. Topological photonics: an observation of Landau levels for optical photons

    NASA Astrophysics Data System (ADS)

    Schine, Nathan; Ryou, Albert; Sommer, Ariel; Simon, Jonathan

    Creating photonic materials with nontrivial topological characteristics has seen burgeoning interest in recent years; however, a major route to topology, a magnetic field for continuum photons, has remained elusive. We present the first experimental realization of a bulk magnetic field for optical photons. By using a non-planar ring resonator, we induce an image rotation on each round trip through the resonator. This results in a Coriolis/Lorentz force and a centrifugal anticonfining force, the latter of which is cancelled by mirror curvature. Spatial- and energy- resolved spectroscopy tracks photonic eigenstates as residual trapping is reduced, and we observe photonic Landau levels as the eigenstates become degenerate. We will discuss the conical geometry of the resulting manifold for photon dynamics and present a measurement of the local density of states that is consistent with Landau levels on a cone. While our work already demonstrates an integer quantum Hall material composed of photons, we have ensured compatibility with strong photon-photon interactions, which will allow quantum optical studies of entanglement and correlation in manybody systems including fractional quantum Hall fluids. This work was supported by DOE, DARPA, and AFOSR.

  12. Photon correlation in single-photon frequency upconversion.

    PubMed

    Gu, Xiaorong; Huang, Kun; Pan, Haifeng; Wu, E; Zeng, Heping

    2012-01-30

    We experimentally investigated the intensity cross-correlation between the upconverted photons and the unconverted photons in the single-photon frequency upconversion process with multi-longitudinal mode pump and signal sources. In theoretical analysis, with this multi-longitudinal mode of both signal and pump sources system, the properties of the signal photons could also be maintained as in the single-mode frequency upconversion system. Experimentally, based on the conversion efficiency of 80.5%, the joint probability of simultaneously detecting at upconverted and unconverted photons showed an anti-correlation as a function of conversion efficiency which indicated the upconverted photons were one-to-one from the signal photons. While due to the coherent state of the signal photons, the intensity cross-correlation function g(2)(0) was shown to be equal to unity at any conversion efficiency, agreeing with the theoretical prediction. This study will benefit the high-speed wavelength-tunable quantum state translation or photonic quantum interface together with the mature frequency tuning or longitudinal mode selection techniques.

  13. 43 CFR 10.8 - Summaries.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... REGULATIONS Human Remains, Funerary Objects, Sacred Objects, or Objects of Cultural Patrimony in Museums and... may contain unassociated funerary objects, sacred objects, or objects of cultural patrimony must... repatriation of such objects. The summary serves in lieu of an object-by-object inventory of these...

  14. 43 CFR 10.8 - Summaries.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ...: Interior Office of the Secretary of the Interior NATIVE AMERICAN GRAVES PROTECTION AND REPATRIATION REGULATIONS Human Remains, Funerary Objects, Sacred Objects, or Objects of Cultural Patrimony in Museums and... may contain unassociated funerary objects, sacred objects, or objects of cultural patrimony...

  15. 43 CFR 10.8 - Summaries.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ...: Interior Office of the Secretary of the Interior NATIVE AMERICAN GRAVES PROTECTION AND REPATRIATION REGULATIONS Human Remains, Funerary Objects, Sacred Objects, or Objects of Cultural Patrimony in Museums and... may contain unassociated funerary objects, sacred objects, or objects of cultural patrimony...

  16. 43 CFR 10.8 - Summaries.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... of a deceased Native American individual with whom unassociated funerary objects and sacred objects...: Interior Office of the Secretary of the Interior NATIVE AMERICAN GRAVES PROTECTION AND REPATRIATION REGULATIONS Human Remains, Funerary Objects, Sacred Objects, or Objects of Cultural Patrimony in Museums...

  17. 43 CFR 10.8 - Summaries.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... of a deceased Native American individual with whom unassociated funerary objects and sacred objects...: Interior Office of the Secretary of the Interior NATIVE AMERICAN GRAVES PROTECTION AND REPATRIATION REGULATIONS Human Remains, Funerary Objects, Sacred Objects, or Objects of Cultural Patrimony in Museums...

  18. 15 CFR 10.8 - Standing Committee.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... practices relating to the standard. (e) The committee shall: (1) Keep itself informed of any advancing technology that might affect the standard; (2) Provide the Department with interpretations of provisions...

  19. 15 CFR 10.8 - Standing Committee.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... practices relating to the standard. (e) The committee shall: (1) Keep itself informed of any advancing technology that might affect the standard; (2) Provide the Department with interpretations of provisions...

  20. 15 CFR 10.8 - Standing Committee.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... practices relating to the standard. (e) The committee shall: (1) Keep itself informed of any advancing technology that might affect the standard; (2) Provide the Department with interpretations of provisions...

  1. 15 CFR 10.8 - Standing Committee.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... practices relating to the standard. (e) The committee shall: (1) Keep itself informed of any advancing technology that might affect the standard; (2) Provide the Department with interpretations of provisions...

  2. All-photonic quantum repeaters.

    PubMed

    Azuma, Koji; Tamaki, Kiyoshi; Lo, Hoi-Kwong

    2015-01-01

    Quantum communication holds promise for unconditionally secure transmission of secret messages and faithful transfer of unknown quantum states. Photons appear to be the medium of choice for quantum communication. Owing to photon losses, robust quantum communication over long lossy channels requires quantum repeaters. It is widely believed that a necessary and highly demanding requirement for quantum repeaters is the existence of matter quantum memories. Here we show that such a requirement is, in fact, unnecessary by introducing the concept of all-photonic quantum repeaters based on flying qubits. In particular, we present a protocol based on photonic cluster-state machine guns and a loss-tolerant measurement equipped with local high-speed active feedforwards. We show that, with such all-photonic quantum repeaters, the communication efficiency scales polynomially with the channel distance. Our result paves a new route towards quantum repeaters with efficient single-photon sources rather than matter quantum memories.

  3. Quantum simulation with interacting photons

    NASA Astrophysics Data System (ADS)

    Hartmann, Michael J.

    2016-10-01

    Enhancing optical nonlinearities so that they become appreciable on the single photon level and lead to nonclassical light fields has been a central objective in quantum optics for many years. After this has been achieved in individual micro-cavities representing an effectively zero-dimensional volume, this line of research has shifted its focus towards engineering devices where such strong optical nonlinearities simultaneously occur in extended volumes of multiple nodes of a network. Recent technological progress in several experimental platforms now opens the possibility to employ the systems of strongly interacting photons, these give rise to as quantum simulators. Here we review the recent development and current status of this research direction for theory and experiment. Addressing both, optical photons interacting with atoms and microwave photons in networks of superconducting circuits, we focus on analogue quantum simulations in scenarios where effective photon-photon interactions exceed dissipative processes in the considered platforms.

  4. Nonlinear interaction between single photons.

    PubMed

    Guerreiro, T; Martin, A; Sanguinetti, B; Pelc, J S; Langrock, C; Fejer, M M; Gisin, N; Zbinden, H; Sangouard, N; Thew, R T

    2014-10-24

    Harnessing nonlinearities strong enough to allow single photons to interact with one another is not only a fascinating challenge but also central to numerous advanced applications in quantum information science. Here we report the nonlinear interaction between two single photons. Each photon is generated in independent parametric down-conversion sources. They are subsequently combined in a nonlinear waveguide where they are converted into a single photon of higher energy by the process of sum-frequency generation. Our approach results in the direct generation of photon triplets. More generally, it highlights the potential for quantum nonlinear optics with integrated devices and, as the photons are at telecom wavelengths, it opens the way towards novel applications in quantum communication such as device-independent quantum key distribution.

  5. Single-photon quadratic optomechanics

    PubMed Central

    Liao, Jie-Qiao; Nori, Franco

    2014-01-01

    We present exact analytical solutions to study the coherent interaction between a single photon and the mechanical motion of a membrane in quadratic optomechanics. We consider single-photon emission and scattering when the photon is initially inside the cavity and in the fields outside the cavity, respectively. Using our solutions, we calculate the single-photon emission and scattering spectra, and find relations between the spectral features and the system's inherent parameters, such as: the optomechanical coupling strength, the mechanical frequency, and the cavity-field decay rate. In particular, we clarify the conditions for the phonon sidebands to be visible. We also study the photon-phonon entanglement for the long-time emission and scattering states. The linear entropy is employed to characterize this entanglement by treating it as a bipartite one between a single mode of phonons and a single photon. PMID:25200128

  6. All-photonic quantum repeaters

    PubMed Central

    Azuma, Koji; Tamaki, Kiyoshi; Lo, Hoi-Kwong

    2015-01-01

    Quantum communication holds promise for unconditionally secure transmission of secret messages and faithful transfer of unknown quantum states. Photons appear to be the medium of choice for quantum communication. Owing to photon losses, robust quantum communication over long lossy channels requires quantum repeaters. It is widely believed that a necessary and highly demanding requirement for quantum repeaters is the existence of matter quantum memories. Here we show that such a requirement is, in fact, unnecessary by introducing the concept of all-photonic quantum repeaters based on flying qubits. In particular, we present a protocol based on photonic cluster-state machine guns and a loss-tolerant measurement equipped with local high-speed active feedforwards. We show that, with such all-photonic quantum repeaters, the communication efficiency scales polynomially with the channel distance. Our result paves a new route towards quantum repeaters with efficient single-photon sources rather than matter quantum memories. PMID:25873153

  7. Investigation of 2D photonic crystal structure based channel drop filter using quad shaped photonic crystal ring resonator for CWDM system

    NASA Astrophysics Data System (ADS)

    Chhipa, Mayur Kumar; Dusad, Lalit Kumar

    2016-05-01

    In this paper, the design & performance of two dimensional (2-D) photonic crystal structure based channel drop filter is investigated using quad shaped photonic crystal ring resonator. In this paper, Photonic Crystal (PhC) based on square lattice periodic arrays of Gallium Indium Phosphide (GaInP) rods in air structure have been investigated using Finite Difference Time Domain (FDTD) method and photonic band gap is being calculated using Plane Wave Expansion (PWE) method. The PhC designs have been optimized for telecommunication wavelength λ= 1571 nm by varying the rods lattice constant. The number of rods in Z and X directions is 21 and 20, with lattice constant 0.540 nm it illustrates that the arrangement of Gallium Indium Phosphide (GaInP) rods in the structure which gives the overall size of the device around 11.4 µm × 10.8 µm. The designed filter gives good dropping efficiency using 3.298, refractive index. The designed structure is useful for CWDM systems. This device may serve as a key component in photonic integrated circuits. The device is ultra compact with the overall size around 123 µm2.

  8. Secondary bremsstrahlung and the energy-conservation aspects of kerma in photon-irradiated media

    NASA Astrophysics Data System (ADS)

    Kumar, Sudhir; Nahum, Alan E.

    2016-02-01

    Kerma, collision kerma and absorbed dose in media irradiated by megavoltage photons are analysed with respect to energy conservation. The user-code DOSRZnrc was employed to compute absorbed dose D, kerma K and a special form of kerma, K ncpt, obtained by setting the charged-particle transport energy cut-off very high, thereby preventing the generation of ‘secondary bremsstrahlung’ along the charged-particle paths. The user-code FLURZnrc was employed to compute photon fluence, differential in energy, from which collision kerma, K col and K were derived. The ratios K/D, K ncpt/D and K col/D have thereby been determined over a very large volumes of water, aluminium and copper irradiated by broad, parallel beams of 0.1 to 25 MeV monoenergetic photons, and 6, 10 and 15 MV ‘clinical’ radiotherapy qualities. Concerning depth-dependence, the ‘area under the kerma, K, curve’ exceeded that under the dose curve, demonstrating that kerma does not conserve energy when computed over a large volume. This is due to the ‘double counting’ of the energy of the secondary bremsstrahlung photons, this energy being (implicitly) included in the kerma ‘liberated’ in the irradiated medium, at the same time as this secondary bremsstrahlung is included in the photon fluence which gives rise to kerma elsewhere in the medium. For 25 MeV photons this ‘violation’ amounts to 8.6%, 14.2% and 25.5% in large volumes of water, aluminium and copper respectively but only 0.6% for a ‘clinical’ 6 MV beam in water. By contrast, K col/D and K ncpt/D, also computed over very large phantoms of the same three media, for the same beam qualities, are equal to unity within (very low) statistical uncertainties, demonstrating that collision kerma and the special type of kerma, K ncpt, do conserve energy over a large volume. A comparison of photon fluence spectra for the 25 MeV beam at a depth of  ≈51 g cm-2 for both very high and very low charged-particle transport cut

  9. Silicon photonic integration in telecommunications

    NASA Astrophysics Data System (ADS)

    Doerr, Christopher

    2015-08-01

    Silicon photonics is the guiding of light in a planar arrangement of silicon-based materials to perform various functions. We focus here on the use of silicon photonics to create transmitters and receivers for fiber-optic telecommunications. As the need to squeeze more transmission into a given bandwidth, a given footprint, and a given cost increases, silicon photonics makes more and more economic sense.

  10. Silicon photonic heater-modulator

    DOEpatents

    Zortman, William A.; Trotter, Douglas Chandler; Watts, Michael R.

    2015-07-14

    Photonic modulators, methods of forming photonic modulators and methods of modulating an input optical signal are provided. A photonic modulator includes a disk resonator having a central axis extending along a thickness direction of the disk resonator. The disk resonator includes a modulator portion and a heater portion. The modulator portion extends in an arc around the central axis. A PN junction of the modulator portion is substantially normal to the central axis.

  11. Spaceborne Photonics Institute

    NASA Technical Reports Server (NTRS)

    Venable, D. D.; Farrukh, U. O.; Han, K. S.; Hwang, I. H.; Jalufka, N. W.; Lowe, C. W.; Tabibi, B. M.; Lee, C. J.; Lyons, D.; Maclin, A.

    1994-01-01

    This report describes in chronological detail the development of the Spaceborne Photonics Institute as a sustained research effort at Hampton University in the area of optical physics. This provided the research expertise to initiate a PhD program in Physics. Research was carried out in the areas of: (1) modelling of spaceborne solid state laser systems; (2) amplified spontaneous emission in solar pumped iodine lasers; (3) closely simulated AM0 CW solar pumped iodine laser and repeatedly short pulsed iodine laser oscillator; (4) a materials spectroscopy and growth program; and (5) laser induced fluorescence and atomic and molecular spectroscopy.

  12. Robust Photon Locking

    SciTech Connect

    Bayer, T.; Wollenhaupt, M.; Sarpe-Tudoran, C.; Baumert, T.

    2009-01-16

    We experimentally demonstrate a strong-field coherent control mechanism that combines the advantages of photon locking (PL) and rapid adiabatic passage (RAP). Unlike earlier implementations of PL and RAP by pulse sequences or chirped pulses, we use shaped pulses generated by phase modulation of the spectrum of a femtosecond laser pulse with a generalized phase discontinuity. The novel control scenario is characterized by a high degree of robustness achieved via adiabatic preparation of a state of maximum coherence. Subsequent phase control allows for efficient switching among different target states. We investigate both properties by photoelectron spectroscopy on potassium atoms interacting with the intense shaped light field.

  13. Generalized Fibonacci photon sieves.

    PubMed

    Ke, Jie; Zhang, Junyong

    2015-08-20

    We successfully extend the standard Fibonacci zone plates with two on-axis foci to the generalized Fibonacci photon sieves (GFiPS) with multiple on-axis foci. We also propose the direct and inverse design methods based on the characteristic roots of the recursion relation of the generalized Fibonacci sequences. By switching the transparent and opaque zones, according to the generalized Fibonacci sequences, we not only realize adjustable multifocal distances but also fulfill the adjustable compression ratio of focal spots in different directions. PMID:26368763

  14. Silicon active photonic devices

    NASA Astrophysics Data System (ADS)

    Dimitropoulos, Dimitrios

    Active photonic devices utilizing the optical nonlinearities of silicon have emerged in the last 5 years and the effort for commercial photonic devices in the material that has been the workhorse of electronics has been building up since. This dissertation presents the theory for some of these devices. We are concerned herein with CW lasers, amplifiers and wavelength converters that are based on the Raman effect. There have already been cursory experimental demonstrations of these devices and some of their limitations are already apparent. Most of the limitations observed are because of the appearance of effects that are competing with stimulated Raman scattering. Under the high optical powers that are necessary for the Raman effect (tens to hundrends of mW's) the process of optical two-photon (TPA) absorption occurs. The absorption of optical power that it causes itself is weak but in the process electrons and holes are generated which can further absorb light through the free-carrier absorption effect (FCA). The effective "lifetime" that these carriers have determines the magnitude of the FCA loss. We present a model for the carrier lifetime in Silicon-On-Insulator (SOI) waveguides and numerical simulations to understand how this critical parameter varies and how it can be controlled. A p-i-n junction built along SOI waveguides can help achieve lifetime of the order of 20--100 ps but the price one has to pay is on-chip electrical power consumption on the order of 100's of mWs. We model CW Raman lasers and we find that the carrier lifetime reduces the output power. If the carrier lifetime exceeds a certain "critical" value optical losses become overwhelming and lasing is impossible. As we show, in amplifiers, the nonlinear loss does not only result in diminished gain, but also in a higher noise figure. Finally the effect of Coherent anti-Stokes Raman scattering (CARS) is examined. The effect is important because with a pump frequency at 1434nm coherent power

  15. Photon-impenetrable, electron-permeable: the carbon nanotube forest as a medium for multiphoton thermal-photoemission.

    PubMed

    Vahdani Moghaddam, Mehran; Yaghoobi, Parham; Sawatzky, George A; Nojeh, Alireza

    2015-04-28

    Combining the photoelectric and thermionic mechanisms to generate free electrons has been of great interest since the early days of quantum physics as exemplified by the Fowler-DuBridge theory, and recently proposed for highly efficient solar conversion. We present experimental evidence of this combined effect over the entire range spanning room-temperature photoemission to thermionic emission. Remarkably, the optical stimulus alone is responsible for both heating and photoemission at the same time. Moreover, the current depends on optical intensity quadratically, indicating two-photon photoemission, for intensities of ca. 1-50 W/cm(2), which are orders of magnitude below the intensities required for two-photon photoemission from bulk metals. This surprising behavior appears to be enabled by the internal nanostructure of the carbon nanotube forest, which captures photons effectively, yet allows electrons to escape easily.

  16. Photon-impenetrable, electron-permeable: the carbon nanotube forest as a medium for multiphoton thermal-photoemission.

    PubMed

    Vahdani Moghaddam, Mehran; Yaghoobi, Parham; Sawatzky, George A; Nojeh, Alireza

    2015-04-28

    Combining the photoelectric and thermionic mechanisms to generate free electrons has been of great interest since the early days of quantum physics as exemplified by the Fowler-DuBridge theory, and recently proposed for highly efficient solar conversion. We present experimental evidence of this combined effect over the entire range spanning room-temperature photoemission to thermionic emission. Remarkably, the optical stimulus alone is responsible for both heating and photoemission at the same time. Moreover, the current depends on optical intensity quadratically, indicating two-photon photoemission, for intensities of ca. 1-50 W/cm(2), which are orders of magnitude below the intensities required for two-photon photoemission from bulk metals. This surprising behavior appears to be enabled by the internal nanostructure of the carbon nanotube forest, which captures photons effectively, yet allows electrons to escape easily. PMID:25769341

  17. Photonic crystal fibers in biophotonics

    NASA Astrophysics Data System (ADS)

    Tuchin, Valery V.; Skibina, Julia S.; Malinin, Anton V.

    2011-12-01

    We observed recent experimental results in area of photonic crystal fibers appliance. Possibility of creation of fiberbased broadband light sources for high resolution optical coherence tomography is discussed. Using of femtosecond pulse laser allows for generation of optical radiation with large spectral width in highly nonlinear solid core photonic crystal fibers. Concept of exploitation of hollow core photonic crystal fibers in optical sensing is demonstrated. The use of photonic crystal fibers as "smart cuvette" gives rise to efficiency of modern optical biomedical analysis methods.

  18. Phenomenology of photon-jets

    NASA Astrophysics Data System (ADS)

    Ellis, Stephen D.; Roy, Tuhin S.; Scholtz, Jakub

    2013-01-01

    One of the challenges of collider physics is to unambiguously associate detector-based objects with the corresponding elementary physics objects. A particular example is the association of calorimeter-based objects such as “jets,” identified with a standard (IR-safe) jet algorithm, with the underlying physics objects, which may be QCD-jets (arising from a scattered parton), electrons, photons or, as discussed here, photon-jets (a group of collinear photons). This separation is especially interesting in the context of Higgs search, where the signal includes events with two photons (in the Standard Model) as well as events with two photon-jets (in a variety of Beyond the Standard Model scenarios), while QCD provides ever-present background. Here we describe the implementation of techniques from the rapidly evolving area of jet substructure studies, not only to enhance the more familiar photon-QCD separation, but also to separately distinguish photon-jets, i.e., to separate usual jets into three categories: single photons, photon-jets and QCD-jets. The efficacy of these techniques for separation is illustrated through studies of simulated data.

  19. Hologram of a single photon

    NASA Astrophysics Data System (ADS)

    Chrapkiewicz, Radosław; Jachura, Michał; Banaszek, Konrad; Wasilewski, Wojciech

    2016-09-01

    The spatial structure of single photons is becoming an extensively explored resource to facilitate free-space quantum communication and quantum computation as well as for benchmarking the limits of quantum entanglement generation with orbital angular momentum modes or reduction of the photon free-space propagation speed. Although accurate tailoring of the spatial structure of photons is now routinely performed using methods employed for shaping classical optical beams, the reciprocal problem of retrieving the spatial phase-amplitude structure of an unknown single photon cannot be solved using complementary classical holography techniques that are known for excellent interferometric precision. Here, we introduce a method to record a hologram of a single photon that is probed by another reference photon, on the basis of a different concept of the quantum interference between two-photon probability amplitudes. As for classical holograms, the hologram of a single photon encodes the full information about the photon's ‘shape’ (that is, its quantum wavefunction) whose local amplitude and phase are retrieved in the demonstrated experiment.

  20. Photonic Landau levels on cones

    NASA Astrophysics Data System (ADS)

    Schine, Nathan; Ryou, Albert; Gromov, Andrey; Sommer, Ariel; Simon, Jonathan

    2016-05-01

    Creating photonic materials with nontrivial topological characteristics has seen burgeoning interest in recent years; however, a major route to topology, a magnetic field for continuum photons, has remained elusive. We present the first experimental realization of a bulk magnetic field for optical photons. By using a non-planar ring resonator, we induce an image rotation on each round trip through the resonator. This results in a Coriolis/Lorentz force and a centrifugal anticonfining force, the latter of which is cancelled by mirror curvature. Spatial- and energy- resolved spectroscopy tracks photonic eigenstates as residual trapping is reduced, and we observe photonic Landau levels as the eigenstates become degenerate. We will discuss the conical geometry of the resulting manifold for photon dynamics and present a measurement of the local density of states that is consistent with Landau levels on a cone. While our work already demonstrates an integer quantum Hall material composed of photons, we have ensured compatibility with strong photon-photon interactions, which will allow quantum optical studies of entanglement and correlation in manybody systems including fractional quantum Hall fluids.

  1. Coupling localized plasmonic and photonic modes tailors and boosts ultrafast light modulation by gold nanoparticles.

    PubMed

    Wang, Xiaoli; Morea, Roberta; Gonzalo, Jose; Palpant, Bruno

    2015-04-01

    Plasmonic nanoparticles offer a broad range of functionalities, owing to their ability to amplify light in the near-field or convert it into heat. However, their ultrafast nonlinear optical response remains too low to envisage all-optical high-rate photonic processing applications. Here, we tackle this challenge by coupling the localized plasmon mode in gold nanoparticles with a localized photonic mode in a 1D resonant cavity. Despite the nonradiative losses, we demonstrate that a strong, reversible, and ultrafast optical modulation can be achieved. By using a light pumping fluence of less than 1 mJ cm(-2), a change of signal transmittance of more than 100% is generated within a few picosecond time scale. The nanoparticle transient optical response is enhanced by a factor of 30 to 40 while its spectral profile is strongly sharpened. The large nonlinear response of such plasmonic cavities could open new opportunities for ultrafast light processing at the nanoscale.

  2. Photon Molecules in Atomic Gases Trapped Near Photonic Crystal Waveguides

    NASA Astrophysics Data System (ADS)

    Douglas, James S.; Caneva, Tommaso; Chang, Darrick E.

    2016-07-01

    Realizing systems that support robust, controlled interactions between individual photons is an exciting frontier of nonlinear optics. To this end, one approach that has emerged recently is to leverage atomic interactions to create strong and spatially nonlocal interactions between photons. In particular, effective photonic interactions have been successfully created via interactions between atoms excited to Rydberg levels. Here, we investigate an alternative approach, in which atomic interactions arise via their common coupling to photonic crystal waveguides. This technique takes advantage of the ability to separately tailor the strength and range of interactions via the dispersion engineering of the structure itself, which can lead to qualitatively new types of phenomena. For example, much of the work on photon-photon interactions relies on the linear optical effect of electromagnetically induced transparency, in combination with the use of interactions to shift optical pulses into or out of the associated transparency window. Here, we identify a large new class of "correlated transparency windows," in which photonic states of a certain number and shape selectively propagate through the system. Through this technique, we show that molecular bound states of photon pairs can be created.

  3. The ubiquitous photonic wheel

    NASA Astrophysics Data System (ADS)

    Aiello, Andrea; Banzer, Peter

    2016-08-01

    A circularly polarized electromagnetic plane wave carries an electric field that rotates clockwise or counterclockwise around the propagation direction of the wave. According to the handedness of this rotation, its longitudinal spin angular momentum (AM) density is either parallel or antiparallel to the propagation of light. However, there are also light waves that are not simply plane and carry an electric field that rotates around an axis perpendicular to the propagation direction, thus yielding transverse spin AM density. Electric field configurations of this kind have been suggestively dubbed ‘photonic wheels’. It has been recently shown that photonic wheels are commonplace in optics as they occur in electromagnetic fields confined by waveguides, in strongly focused beams, in plasmonic and evanescent waves. In this work we establish a general theory of electromagnetic waves propagating along a well defined direction, and carrying transverse spin AM density. We show that depending on the shape of these waves, the spin density may be either perpendicular to the mean linear momentum (globally transverse spin) or to the linear momentum density (locally transverse spin). We find that the latter case generically occurs only for non-diffracting beams, such as the Bessel beams. Moreover, we introduce the concept of meridional Stokes parameters to operationally quantify the transverse spin density. To illustrate our theory, we apply it to the exemplary cases of Bessel beams and evanescent waves. These results open a new and accessible route to the understanding, generation and manipulation of optical beams with transverse spin AM density.

  4. Smart photonic carbon brush

    NASA Astrophysics Data System (ADS)

    Morozov, Oleg G.; Kuznetsov, Artem A.; Morozov, Gennady A.; Nureev, Ilnur I.; Sakhabutdinov, Airat Z.; Faskhutdinov, Lenar M.; Artemev, Vadim I.

    2016-03-01

    Aspects of the paper relate to a wear monitoring system for smart photonic carbon brush. There are many applications in which regular inspection is not feasible because of a number of factors including, for example, time, labor, cost and disruptions due to down time. Thus, there is a need for a system that can monitor the wear of a component while the component is in operation or without having to remove the component from its operational position. We propose a new smart photonic method for characterization of carbon brush wear. It is based on the usage of advantages of the multiplicative response of FBG and LPFG sensors and its double-frequency probing. Additional measuring parameters are the wear rate, the brush temperature, the engine rotation speed, the hangs control, and rotor speed. Sensor is embedded in brush. Firstly the change of sensor length is used to measure wear value and its central wavelength shift for temperature ones. The results of modeling and experiments are presented.

  5. Ion photon emission microscopy

    NASA Astrophysics Data System (ADS)

    Rossi, P.; Doyle, B. L.; Banks, J. C.; Battistella, A.; Gennaro, G.; McDaniel, F. D.; Mellon, M.; Vittone, E.; Vizkelethy, G.; Wing, N. D.

    2003-09-01

    A new ion-induced emission microscopy has been invented and demonstrated, which is called ion photon emission microscopy (IPEM). It employs a low current, broad ion beam impinging on a sample, previously coated or simply covered with a few microns of a fast, highly efficient phosphor layer. The light produced at the single ion impact point is collected with an optical microscope and projected at high magnification onto a single photon position sensitive detector (PSD). This allows maps of the ion strike effects to be produced, effectively removing the need for a microbeam. Irradiation in air and even the use of alpha particle sources with no accelerator are possible. Potential applications include ion beam induced charge collection studies of semiconducting and insulating materials, single event upset studies on microchips and even biological cells in radiobiological effectiveness experiments. We describe the IPEM setup, including a 60× OM-40 microscope with a 1.5 mm hole for the beam transmission and a Quantar PSD with 60 μm pixel. Bicron plastic scintillator blades of 10 μm were chosen as a phosphor for their nanosecond time resolution, homogeneity, utility and commercial availability. The results given in this paper are for a prototype IPEM system. They indicate a resolution of ˜12 μm, the presence of a spatial halo and a He-ion efficiency of ˜20%. This marks the first time that nuclear microscopy has been performed with a radioactive source.

  6. Photonic Band Engineering

    NASA Astrophysics Data System (ADS)

    Yabonovitch, Eli

    2001-09-01

    Scientists at UCLA, Caltech, and Polytechnic University have developed a new concept in Electromagnetics called "Photonic Bandgaps' that permits unprecedented control of Electromagnetic Waves, at both radio frequencies, and optical frequencies. This new paradigm of Electromagnetics is based on Nature's design for semiconductor crystals, but it is a crystal structure that is artificially engineered for electromagnetic waves rather than for electron waves. Beginning in 1996, new frontiers in the engineered control of electromagnetic waves have emerged from this design paradigm. For example, the very tiniest, most miniaturized electromagnetic cavity ever created was engineered, and demonstrated, under this MURI; trapping optical energy in the smallest volume ever achieved. This world's most tiny light trap was also made into the most miniaturized laser ever made, occupying a volume smaller than a cubic wavelength. At the same time this MURI advanced the electromagnetic bandgap concept into microwaves and radio waves that are so important for military systems. This required new concepts that permitted the bandgap structure to be much smaller than the electromagnetic wavelength. As in the optical version of photonic crystals, these electromagnetic bandgaps permit unprecedented control over radio frequency electromagnetic waves. For example new antenna structures have been invented that permit near field control over radio emissions from antennas, so that the hand-held radio transmitters can be more efficient.

  7. Octonacci photonic quasicrystals

    NASA Astrophysics Data System (ADS)

    Brandão, E. R.; Costa, C. H.; Vasconcelos, M. S.; Anselmo, D. H. A. L.; Mello, V. D.

    2015-08-01

    We study theoretically the transmission spectra in one-dimensional photonic quasicrystals, made up of SiO2(A) and TiO2(B) materials, organized following the Octonacci sequence, where the nth-stage of the multilayer Sn is given by the rule Sn =Sn-1Sn-2Sn-1 , for n ⩾ 3 and with S1 = A and S2 = B . The expression for transmittance was obtained by employing a theoretical calculation based on the transfer-matrix method. For normally incident waves, we observe that, for a same generation, the transmission spectra for transverse electric (TE) and transverse magnetic (TM) waves are equal, at least qualitatively, and they present a scaling property where a self-similar behavior is obtained, as an evidence that these spectra are fractals. The spectra show regions where the omnidirectional band gaps emerges for specific generations of Octonacci photonic structure, except to TM waves. For TE waves, we note that all of them have almost the same width, for different generations. We also report the localization of modes as a consequence of the quasiperiodicity of the heterostructure.

  8. Enhanced Multi-MeV Photon Emission by a Laser-Driven Electron Beam in a Self-Generated Magnetic Field.

    PubMed

    Stark, D J; Toncian, T; Arefiev, A V

    2016-05-01

    We use numerical simulations to demonstrate that a source of collimated multi-MeV photons with high conversion efficiency can be achieved using an all-optical single beam setup at an intensity of 5×10^{22}  W/cm^{2} that is already within reach of existing laser facilities. In the studied setup, an unprecedented quasistatic magnetic field (0.4 MT) is driven in a significantly overdense plasma, coupling three key aspects of laser-plasma interactions at high intensities: relativistic transparency, direct laser acceleration, and synchrotron photon emission. The quasistatic magnetic field enhances the photon emission process, which has a profound impact on electron dynamics via radiation reaction and yields tens of TW of directed MeV photons for a PW-class laser. PMID:27203330

  9. Single photonics: Generation and detection of heralded single photons

    NASA Astrophysics Data System (ADS)

    Kim, Jungsang

    Single photons are useful for experiments where the quantum nature of a particle plays a key role, since they make an ideal candidate for a single quantum system. Such a single quantum system is indispensable in fundamental tests of quantum mechanics where nonclassical properties, like non-locality and entanglement, are studied. Such a system is also useful in a more recently developed field of quantum information technology where these properties are utilized to perform secure communication and information processing. In the source of single photons utilized in these experiments, the arrival time of the photon is completely random and obeys Poissonian statistics. Efficiency of these experiments can be greatly enhanced when the arrival time of the photons can be controlled. Also, a technology that provides high quantum efficiency and low noise detection of single photons is crucial to improve the performance of these experimental schemes. This thesis reports an experimental effort towards realization of a single photon turnstile device where the emission time of a single photon can be controlled by means of an external modulation signal. This is achieved in a mesoscopic double barrier p- i-n junction operating in an ultra-low temperature environment, where the Coulomb charging energy of a single electron and a single hole is large enough to suppress the thermal fluctuation of carrier injection. One and only one electron-hole pair is injected into the active region, resulting in the emission of a single photon per modulation period. This thesis also reports a single photon counting system using a visible light photon counter (VLPC), which utilizes the impact ionization of As impurity atoms in Si as the multiplication process. Our system features a fast (~2 ns) detection of single photons with high quantum efficiency (~88%) and low multiplication noise (excess noise factor ~1.02). The detector system also has a unique capability of distinguishing a single photon

  10. Photonic module: An on-demand resource for photonic entanglement

    SciTech Connect

    Devitt, Simon J.; Greentree, Andrew D.; Hollenberg, Lloyd C. L.; Ionicioiu, Radu; O'Brien, Jeremy L.; Munro, William J.

    2007-11-15

    Photonic entanglement has a wide range of applications in quantum computation and communication. Here we introduce a device: the photonic module, which allows for the rapid, deterministic preparation of a large class of entangled photon states. The module is an application independent, ''plug and play'' device, with sufficient flexibility to prepare entanglement for all major quantum computation and communication applications in a completely deterministic fashion without number-discriminated photon detection. We present two alternative constructions for the module, one using free-space components and one in a photonic band-gap structure. The natural operation of the module is to generate states within the stabilizer formalism and we present an analysis on the cavity requirements to experimentally realize this device.

  11. Broadband photon-photon interactions mediated by cold atoms in a photonic crystal fiber

    PubMed Central

    Litinskaya, Marina; Tignone, Edoardo; Pupillo, Guido

    2016-01-01

    We demonstrate theoretically that photon-photon attraction can be engineered in the continuum of scattering states for pairs of photons propagating in a hollow-core photonic crystal fiber filled with cold atoms. The atoms are regularly spaced in an optical lattice configuration and the photons are resonantly tuned to an internal atomic transition. We show that the hard-core repulsion resulting from saturation of the atomic transitions induces bunching in the photonic component of the collective atom-photon modes (polaritons). Bunching is obtained in a frequency range as large as tens of GHz, and can be controlled by the inter-atomic separation. We provide a fully analytical explanation for this phenomenon by proving that correlations result from a mismatch of the quantization volumes for atomic excitations and photons in the continuum. Even stronger correlations can be observed for in-gap two-polariton bound states. Our theoretical results use parameters relevant for current experiments and suggest a simple and feasible way to induce interactions between photons. PMID:27170160

  12. Progress in 2D photonic crystal Fano resonance photonics

    NASA Astrophysics Data System (ADS)

    Zhou, Weidong; Zhao, Deyin; Shuai, Yi-Chen; Yang, Hongjun; Chuwongin, Santhad; Chadha, Arvinder; Seo, Jung-Hun; Wang, Ken X.; Liu, Victor; Ma, Zhenqiang; Fan, Shanhui

    2014-01-01

    In contrast to a conventional symmetric Lorentzian resonance, Fano resonance is predominantly used to describe asymmetric-shaped resonances, which arise from the constructive and destructive interference of discrete resonance states with broadband continuum states. This phenomenon and the underlying mechanisms, being common and ubiquitous in many realms of physical sciences, can be found in a wide variety of nanophotonic structures and quantum systems, such as quantum dots, photonic crystals, plasmonics, and metamaterials. The asymmetric and steep dispersion of the Fano resonance profile promises applications for a wide range of photonic devices, such as optical filters, switches, sensors, broadband reflectors, lasers, detectors, slow-light and non-linear devices, etc. With advances in nanotechnology, impressive progress has been made in the emerging field of nanophotonic structures. One of the most attractive nanophotonic structures for integrated photonics is the two-dimensional photonic crystal slab (2D PCS), which can be integrated into a wide range of photonic devices. The objective of this manuscript is to provide an in depth review of the progress made in the general area of Fano resonance photonics, focusing on the photonic devices based on 2D PCS structures. General discussions are provided on the origins and characteristics of Fano resonances in 2D PCSs. A nanomembrane transfer printing fabrication technique is also reviewed, which is critical for the heterogeneous integrated Fano resonance photonics. The majority of the remaining sections review progress made on various photonic devices and structures, such as high quality factor filters, membrane reflectors, membrane lasers, detectors and sensors, as well as structures and phenomena related to Fano resonance slow light effect, nonlinearity, and optical forces in coupled PCSs. It is expected that further advances in the field will lead to more significant advances towards 3D integrated photonics, flat

  13. XCOM: Photon Cross Sections Database

    National Institute of Standards and Technology Data Gateway

    SRD 8 XCOM: Photon Cross Sections Database (Web, free access)   A web database is provided which can be used to calculate photon cross sections for scattering, photoelectric absorption and pair production, as well as total attenuation coefficients, for any element, compound or mixture (Z <= 100) at energies from 1 keV to 100 GeV.

  14. Photon detectors with gaseous amplification

    SciTech Connect

    Va`vra, J.

    1996-08-01

    Gaseous photon detectors, including very large 4{pi}-devices such as those incorporated in SLD and DELPHI, are finally delivering physics after many years of hard work. Photon detectors are among the most difficult devices used in physics experiments, because they must achieve high efficiency for photon transport and for the detection of single photoelectrons. Among detector builders, there is hardly anybody who did not make mistakes in this area, and who does not have a healthy respect for the problems involved. This point is stressed in this paper, and it is suggested that only a very small operating phase space is available for running gaseous photon detectors in a very large system with good efficiency and few problems. In this paper the authors discuss what was done correctly or incorrectly in first generation photon detectors, and what would be their recommendations for second generation detectors. 56 refs., 11 figs.

  15. Single Photon diffraction and interference

    NASA Astrophysics Data System (ADS)

    Hodge, John

    2015-04-01

    A previous paper based on the Scalar Theory of Everything studied photon diffraction and interference (IntellectualArchive, Vol.1, No. 3, P. 20, Toronto, Canada July 2012. http://intellectualarchive.com/?link=item&id=597). Several photons were required in the experiment at the same time. Interference experiments with one photon in the experiment at a time also showed interference patterns. The previous paper with the Bohm Interpretation, models of the screen and mask, and the Transaction Interpretation of Quantum Mechanics were combined. The reverse wave required by the Transaction Interpretation was provided by a reflected plenum wave rather than a reverse time wave. The speed of the plenum wave was assumed to be much faster than the speed of photons/light. Using the assumptions of Fraunhofer diffraction resulted in the same equation for the photon distribution on a screen as the intensity pattern of the Fraunhofer diffraction. (http://myplace.frontier.com/ ~ jchodge/)

  16. Collimator-free photon tomography

    DOEpatents

    Dilmanian, F. Avraham; Barbour, Randall L.

    1998-10-06

    A method of uncollimated single photon emission computed tomography includes administering a radioisotope to a patient for producing gamma ray photons from a source inside the patient. Emissivity of the photons is measured externally of the patient with an uncollimated gamma camera at a plurality of measurement positions surrounding the patient for obtaining corresponding energy spectrums thereat. Photon emissivity at the plurality of measurement positions is predicted using an initial prediction of an image of the source. The predicted and measured photon emissivities are compared to obtain differences therebetween. Prediction and comparison is iterated by updating the image prediction until the differences are below a threshold for obtaining a final prediction of the source image.

  17. Collimator-free photon tomography

    DOEpatents

    Dilmanian, F.A.; Barbour, R.L.

    1998-10-06

    A method of uncollimated single photon emission computed tomography includes administering a radioisotope to a patient for producing gamma ray photons from a source inside the patient. Emissivity of the photons is measured externally of the patient with an uncollimated gamma camera at a plurality of measurement positions surrounding the patient for obtaining corresponding energy spectrums thereat. Photon emissivity at the plurality of measurement positions is predicted using an initial prediction of an image of the source. The predicted and measured photon emissivities are compared to obtain differences therebetween. Prediction and comparison is iterated by updating the image prediction until the differences are below a threshold for obtaining a final prediction of the source image. 6 figs.

  18. Characterization of ammonia two-photon laser-induced fluorescence for gas-phase diagnostics

    NASA Astrophysics Data System (ADS)

    Brackmann, Christian; Hole, Odd; Zhou, Bo; Li, Zhongshan S.; Aldén, Marcus

    2014-04-01

    Two-photon laser-induced fluorescence (LIF) of ammonia (NH3) with excitation of the C'- X transition at 304.8 nm and fluorescence detection in the 565 nm C'- A band has been investigated, targeting combustion diagnostics. The impact of laser irradiance, temperature, and pressure has been studied, and simulation of NH3-spectra, fitted to experimental data, facilitated interpretation of the results. The LIF-signal showed quadratic dependence on laser irradiance up to 2 GW/cm2. Stimulated emission, resulting in loss of excited molecules, is induced above 10 GW/cm2, i.e., above irradiances attainable for LIF imaging. Maximum LIF-signal was obtained for excitation at the 304.8 nm bandhead; however, lower temperature sensitivity over the range 400-700 K can be obtained probing lines around 304.9 nm. A decrease in fluorescence signal was observed with pressure up to 5 bar absolute and attributed to collisional quenching. A detection limit of 800 ppm, at signal-to-noise ratio 1.5, was identified for single-shot LIF imaging over an area of centimeter scale, whereas for single-point measurements, the technique shows potential for sub-ppm detection. Moreover, high-quality NH3-imaging has been achieved in laminar and turbulent premixed flames. Altogether, two-photon fluorescence provides a useful tool for imaging NH3-detection in combustion diagnostics.

  19. Performance of the EIGER single photon counting detector

    NASA Astrophysics Data System (ADS)

    Tinti, G.; Bergamaschi, A.; Cartier, S.; Dinapoli, R.; Greiffenberg, D.; Johnson, I.; Jungmann-Smith, J. H.; Mezza, D.; Mozzanica, A.; Schmitt, B.; Shi, X.

    2015-03-01

    EIGER is a single photon counting hybrid pixel detector being developed at Paul Scherrer Institute (PSI), Switzerland, for applications at synchrotron light sources in an energy range from a few to 25 keV. EIGER is characterized by a small pixel size (75 × 75 μm2), a frame rate up to 22 kHz and a small dead time between frames (4 μs). An EIGER module is a hybrid detector composed of a ≈ 8 × 4 cm2 monolithic silicon sensor bump bonded to 4 × 2 readout chips, for a total of 500 kpixels. Each pixel has a configurable depth (up to 12 bits) counter and records the number of photons impinging. Custom designed module electronics reads out the bits in the pixel counter and processes the data in the module before transferring them to a PC. A large dynamic range (32 bits) for the pixel counter can be obtained through on-board image summation. Rate corrections can be applied on-board to compensate for inefficiencies when the pixel counting rates approach pile-up levels around a million counts per second. The EIGER modules are the building blocks of large area detectors: a 1.5 and a 9 Mpixel systems are under development for the cSAXS beamline at the Swiss Light Source (SLS) at PSI. The very high frame rate capabilities are equally fast for multi-module systems due to the fully parallel data processing.The module calibration will be discussed, with emphasis on the choice of the optimal operation settings as a function of photon energy. The performance regarding threshold dispersion and minimum achievable threshold will be presented. In addition, the progress towards the production of larger multi-module systems will be discussed.

  20. Low Threshold Two-Photon-Pumped Amplified Spontaneous Emission in CH3NH3PbBr3 Microdisks.

    PubMed

    Yang, Bin; Mao, Xin; Yang, Songqiu; Li, Yajuan; Wang, Yanqiu; Wang, Meishan; Deng, Weiqiao; Han, Keli

    2016-08-01

    Two-photon-pumped amplified spontaneous emission (ASE) of CH3NH3PbBr3 microdisks (MDs) were investigated by using femtosecond laser system. Low threshold at 2.2 mJ cm(-2) was obtained. Also, emission spectral tunability from 500 to 570 nm was demonstrated by synthesis the mixed halide perovskite MDs. The spatial effect of photoluminescence (PL) properties under one-photon and two-photon excitation were also studied by means of two-photon laser scanning microscope (TPLSM) and time-resolved PL spectroscopy. It was found that the band to band emission of near-surface regions and photocarriers' diffusion from near-surface regions to interior regions is significant for one-photon excitation. By contrast, reabsorption of emission under two-photon excitation plays a major role in the emission properties of the MDs. These results will give a more comprehensive understanding of the nonlinear effect of CH3NH3PbBr3 single crystals.

  1. Photon-conversion and sensitization evaluation of Eu³⁺ in a borate glass system.

    PubMed

    Tian, Y M; Shen, L F; Pun, E Y B; Lin, H

    2016-02-20

    Photon conversion is exhibited in a borate (LKZBSB) glass system containing Eu(3+), and the enhanced characteristic emissions of Eu(3+) with the codoping of Ce(3+) have been verified. A large Judd-Ofelt intensity parameter Ω2 of Eu(3+) indicates a high asymmetrical and strong covalent environment around rare-earth (RE) ions in LKZBSB glasses and spontaneous emission probability and a maximum emission cross section of the dominant 5D0→7F2 transition were derived to be 370  s(-1) and 1.28×10(-21)  cm2, respectively, revealing the potential UV→visible photon-conversion capacity of Eu(3+). Absolutely quantitative evaluation illustrates that Eu(3+) is a favorable photon-conversion center to achieve high photon-conversion efficiency. The addition of Ce(3+) is beneficial to realizing effective red emission of Eu(3+), which possesses commercial value by decreasing the dopant of expensive europium compounds. As an expectation, this photon-conversion LKZBSB glass system can promote the development of a photon downconversion layer for solar cells, which are particularly used in outer space with intense UV radiation. PMID:26906599

  2. Photon enhanced thermionic emission

    SciTech Connect

    Schwede, Jared; Melosh, Nicholas; Shen, Zhixun

    2014-10-07

    Photon Enhanced Thermionic Emission (PETE) is exploited to provide improved efficiency for radiant energy conversion. A hot (greater than 200.degree. C.) semiconductor cathode is illuminated such that it emits electrons. Because the cathode is hot, significantly more electrons are emitted than would be emitted from a room temperature (or colder) cathode under the same illumination conditions. As a result of this increased electron emission, the energy conversion efficiency can be significantly increased relative to a conventional photovoltaic device. In PETE, the cathode electrons can be (and typically are) thermalized with respect to the cathode. As a result, PETE does not rely on emission of non-thermalized electrons, and is significantly easier to implement than hot-carrier emission approaches.

  3. Photon counting digital holography

    NASA Astrophysics Data System (ADS)

    Demoli, Nazif; Skenderović, Hrvoje; Stipčević, Mario; Pavičić, Mladen

    2016-05-01

    Digital holography uses electronic sensors for hologram recording and numerical method for hologram reconstruction enabling thus the development of advanced holography applications. However, in some cases, the useful information is concealed in a very wide dynamic range of illumination intensities and successful recording requires an appropriate dynamic range of the sensor. An effective solution to this problem is the use of a photon-counting detector. Such detectors possess counting rates of the order of tens to hundreds of millions counts per second, but conditions of recording holograms have to be investigated in greater detail. Here, we summarize our main findings on this problem. First, conditions for optimum recording of digital holograms for detecting a signal significantly below detector's noise are analyzed in terms of the most important holographic measures. Second, for time-averaged digital holograms, optimum recordings were investigated for exposures shorter than the vibration cycle. In both cases, these conditions are studied by simulations and experiments.

  4. Photonic Crystal Nanolaser Biosensors

    NASA Astrophysics Data System (ADS)

    Kita, Shota; Otsuka, Shota; Hachuda, Shoji; Endo, Tatsuro; Imai, Yasunori; Nishijima, Yoshiaki; Misawa, Hiroaki; Baba, Toshihiko

    High-performance and low-cost sensors are critical devices for high-throughput analyses of bio-samples in medical diagnoses and life sciences. In this paper, we demonstrate photonic crystal nanolaser sensor, which detects the adsorption of biomolecules from the lasing wavelength shift. It is a promising device, which balances a high sensitivity, high resolution, small size, easy integration, simple setup and low cost. In particular with a nanoslot structure, it achieves a super-sensitivity in protein sensing whose detection limit is three orders of magnitude lower than that of standard surface-plasmon-resonance sensors. Our investigations indicate that the nanoslot acts as a protein condenser powered by the optical gradient force, which arises from the strong localization of laser mode in the nanoslot.

  5. The Advanced Photon Source

    SciTech Connect

    Galayda, John N.

    1996-01-01

    The Advanced Photon Source (APS) is a 7-GeV third-generation synchrotron radiation storage ring and full-energy positron injector. Construction project funding began in 1989, and ground breaking took place on 5 May 1990. Construction of all accelerator facilities was completed in January 1995 and storage ring commissioning is underway. First observation of x-rays from a bending magnet source took place on 26 March 1995. Nearly all performance specifications of the injector have been reached, and first observations indicate that the reliability, dynamic aperture, emittance, and orbit stability in the storage ring are satisfactory. Observation of radiation from the first of 20 insertion device beamlines is scheduled for October 1995. Start of regular operations is expected to take place well before the APS Project target date of December 1996.

  6. Advances in DNA photonics

    NASA Astrophysics Data System (ADS)

    Heckman, Emily M.; Aga, Roberto S.; Fehrman Cory, Emily M.; Ouchen, Fahima; Lesko, Alyssa; Telek, Brian; Lombardi, Jack; Bartsch, Carrie M.; Grote, James G.

    2012-10-01

    In this paper we present our current research in exploring a DNA biopolymer for photonics applications. A new processing technique has been adopted that employs a modified soxhlet-dialysis (SD) rinsing technique to completely remove excess ionic contaminants from the DNA biopolymer, resulting in a material with greater mechanical stability and enhanced performance reproducibility. This newly processed material has been shown to be an excellent material for cladding layers in poled polymer electro-optic (EO) waveguide modulator applications. Thin film poling results are reported for materials using the DNA biopolymer as a cladding layer, as are results for beam steering devices also using the DNA biopolymer. Finally, progress on fabrication of a Mach Zehnder EO modulator with DNA biopolymer claddings using nanoimprint lithography techniques is reported.

  7. Regenerative photonic therapy: Review

    NASA Astrophysics Data System (ADS)

    Salansky, Natasha; Salansky, Norman

    2012-09-01

    After four decades of research of photobiomodulation phenomena in mammals in vitro and in vivo, a solid foundation is created for the use of photobiomodulation in regenerative medicine. Significant accomplishments are achieved in animal models that demonstrate opportunities for photo-regeneration of injured or pathological tissues: skin, muscles and nerves. However, the use of photobiomodulation in clinical studies leads to controversial results while negative or marginal clinical efficacy is reported along with positive findings. A thor ough analysis of requirements to the optical parameters (dosimetry) for high efficacy in photobimodulation led us to the conclusion that there are several misconceptions in the clinical applications of low level laser therapy (LLLT). We present a novel appr oach of regenerative photonic therapy (RPT) for tissue healing and regeneration that overcomes major drawbacks of LLLT. Encouraging clinical results on RPT efficacy are presented. Requirements for RPT approach and vision for its future development for tissue regeneration is discussed.

  8. Photonic quantum information: science and technology.

    PubMed

    Takeuchi, Shigeki

    2016-01-01

    Recent technological progress in the generation, manipulation and detection of individual single photons has opened a new scientific field of photonic quantum information. This progress includes the realization of single photon switches, photonic quantum circuits with specific functions, and the application of novel photonic states to novel optical metrology beyond the limits of standard optics. In this review article, the recent developments and current status of photonic quantum information technology are overviewed based on the author's past and recent works.

  9. How photons start vision.

    PubMed Central

    Baylor, D

    1996-01-01

    Recent studies have elucidated how the absorption of a photon in a rod or cone cell leads to the generation of the amplified neural signal that is transmitted to higher-order visual neurons. Photoexcited visual pigment activates the GTP-binding protein transducin, which in turn stimulates cGMP phosphodiesterase. This enzyme hydrolyzes cGMP, allowing cGMP-gated cationic channels in the surface membrane to close, hyperpolarize the cell, and modulate transmitter release at the synaptic terminal. The kinetics of reactions in the cGMP cascade limit the temporal resolution of the visual system as a whole, while statistical fluctuations in the reactions limit the reliability of detection of dim light. Much interest now focuses on the processes that terminate the light response and dynamically regulate amplification in the cascade, causing the single photon response to be reproducible and allowing the cell to adapt in background light. A light-induced fall in the internal free Ca2+ concentration coordinates negative feedback control of amplification. The fall in Ca2+ stimulates resynthesis of cGMP, antagonizes rhodopsin's catalytic activity, and increases the affinity of the light-regulated cationic channel for cGMP. We are using physiological methods to study the molecular mechanisms that terminate the flash response and mediate adaptation. One approach is to observe transduction in truncated, dialyzed photoreceptor cells whose internal Ca2+ and nucleotide concentrations are under experimental control and to which exogenous proteins can be added. Another approach is to observe transduction in transgenic mouse rods in which specific proteins within the cascade are altered or deleted. PMID:8570595

  10. Photon-efficient imaging with a single-photon camera

    PubMed Central

    Shin, Dongeek; Xu, Feihu; Venkatraman, Dheera; Lussana, Rudi; Villa, Federica; Zappa, Franco; Goyal, Vivek K.; Wong, Franco N. C.; Shapiro, Jeffrey H.

    2016-01-01

    Reconstructing a scene's 3D structure and reflectivity accurately with an active imaging system operating in low-light-level conditions has wide-ranging applications, spanning biological imaging to remote sensing. Here we propose and experimentally demonstrate a depth and reflectivity imaging system with a single-photon camera that generates high-quality images from ∼1 detected signal photon per pixel. Previous achievements of similar photon efficiency have been with conventional raster-scanning data collection using single-pixel photon counters capable of ∼10-ps time tagging. In contrast, our camera's detector array requires highly parallelized time-to-digital conversions with photon time-tagging accuracy limited to ∼ns. Thus, we develop an array-specific algorithm that converts coarsely time-binned photon detections to highly accurate scene depth and reflectivity by exploiting both the transverse smoothness and longitudinal sparsity of natural scenes. By overcoming the coarse time resolution of the array, our framework uniquely achieves high photon efficiency in a relatively short acquisition time. PMID:27338821

  11. Topological photonics: an observation of Landau levels for optical photons

    NASA Astrophysics Data System (ADS)

    Schine, Nathan; Ryou, Albert; Sommer, Ariel; Simon, Jonathan

    We present the first experimental realization of a bulk magnetic field for optical photons. By using a non-planar ring resonator, we induce an image rotation on each round trip through the resonator. This results in a Coriolis/Lorentz force and a centrifugal anticonfining force, the latter of which is cancelled by mirror curvature. Using a digital micromirror device to control both amplitude and phase, we inject arbitrary optical modes into our resonator. Spatial- and energy- resolved spectroscopy tracks photonic eigenstates as residual trapping is reduced, and we observe photonic Landau levels as the eigenstates become degenerate. We show that there is a conical geometry of the resulting manifold for photon dynamics and present a measurement of the local density of states that is consistent with Landau levels on a cone. While our work already demonstrates an integer quantum Hall material composed of photons, we have ensured compatibility with strong photon-photon interactions, which will allow quantum optical studies of entanglement and correlation in manybody systems including fractional quantum Hall fluids. This work was supported by DOE, DARPA, and AFOSR.

  12. Nonlocal hyperconcentration on entangled photons using photonic module system

    NASA Astrophysics Data System (ADS)

    Cao, Cong; Wang, Tie-Jun; Mi, Si-Chen; Zhang, Ru; Wang, Chuan

    2016-06-01

    Entanglement distribution will inevitably be affected by the channel and environment noise. Thus distillation of maximal entanglement nonlocally becomes a crucial goal in quantum information. Here we illustrate that maximal hyperentanglement on nonlocal photons could be distilled using the photonic module and cavity quantum electrodynamics, where the photons are simultaneously entangled in polarization and spatial-mode degrees of freedom. The construction of the photonic module in a photonic band-gap structure is presented, and the operation of the module is utilized to implement the photonic nondestructive parity checks on the two degrees of freedom. We first propose a hyperconcentration protocol using two identical partially hyperentangled initial states with unknown coefficients to distill a maximally hyperentangled state probabilistically, and further propose a protocol by the assistance of an ancillary single photon prepared according to the known coefficients of the initial state. In the two protocols, the total success probability can be improved greatly by introducing the iteration mechanism, and only one of the remote parties is required to perform the parity checks in each round of iteration. Estimates on the system requirements and recent experimental results indicate that our proposal is realizable with existing or near-further technologies.

  13. Photon-efficient imaging with a single-photon camera

    NASA Astrophysics Data System (ADS)

    Shin, Dongeek; Xu, Feihu; Venkatraman, Dheera; Lussana, Rudi; Villa, Federica; Zappa, Franco; Goyal, Vivek K.; Wong, Franco N. C.; Shapiro, Jeffrey H.

    2016-06-01

    Reconstructing a scene's 3D structure and reflectivity accurately with an active imaging system operating in low-light-level conditions has wide-ranging applications, spanning biological imaging to remote sensing. Here we propose and experimentally demonstrate a depth and reflectivity imaging system with a single-photon camera that generates high-quality images from ~1 detected signal photon per pixel. Previous achievements of similar photon efficiency have been with conventional raster-scanning data collection using single-pixel photon counters capable of ~10-ps time tagging. In contrast, our camera's detector array requires highly parallelized time-to-digital conversions with photon time-tagging accuracy limited to ~ns. Thus, we develop an array-specific algorithm that converts coarsely time-binned photon detections to highly accurate scene depth and reflectivity by exploiting both the transverse smoothness and longitudinal sparsity of natural scenes. By overcoming the coarse time resolution of the array, our framework uniquely achieves high photon efficiency in a relatively short acquisition time.

  14. Higher-order photon correlations in pulsed photonic crystal nanolasers

    SciTech Connect

    Elvira, D.; Hachair, X.; Braive, R.; Beaudoin, G.; Robert-Philip, I.; Sagnes, I.; Abram, I.; Beveratos, A.; Verma, V. B.; Baek, B.; Nam, S. W.; Stevens, M. J.; Dauler, E. A.

    2011-12-15

    We report on the higher-order photon correlations of a high-{beta} nanolaser under pulsed excitation at room temperature. Using a multiplexed four-element superconducting single-photon detector we measured g{sup (n)}(0-vector) with n=2,3,4. All orders of correlation display partially chaotic statistics, even at four times the threshold excitation power. We show that this departure from coherence and Poisson statistics is due to the quantum fluctuations associated with the small number of photons at the lasing threshold.

  15. Two-photon interferences with degenerate and nondegenerate paired photons

    NASA Astrophysics Data System (ADS)

    Liu, Chang; Chen, J. F.; Zhang, Shanchao; Zhou, Shuyu; Kim, Yoon-Ho; Loy, M. M. T.; Wong, G. K. L.; Du, Shengwang

    2012-02-01

    We generate narrow-band frequency-tunable entangled photon pairs from spontaneous four-wave mixing in three-level cold atoms and study their two-photon quantum interference after a beam splitter. We find that the path-exchange symmetry plays a more important role in the Hong-Ou-Mandel interference than the temporal or frequency indistinguishability, and observe coalescence interference for both degenerate and nondegenerate photons. We also observe a quantum beat in the same experimental setup using either slow or fast detectors.

  16. Breakdown of Bragg-Gray behaviour for low-density detectors under electronic disequilibrium conditions in small megavoltage photon fields.

    PubMed

    Kumar, Sudhir; Fenwick, John D; Underwood, Tracy S A; Deshpande, Deepak D; Scott, Alison J D; Nahum, Alan E

    2015-10-21

    In small photon fields ionisation chambers can exhibit large deviations from Bragg-Gray behaviour; the EGSnrc Monte Carlo (MC) code system has been employed to investigate this 'Bragg-Gray breakdown'. The total electron (+positron) fluence in small water and air cavities in a water phantom has been computed for a full linac beam model as well as for a point source spectrum for 6 MV and 15 MV qualities for field sizes from 0.25  ×  0.25 cm(2) to 10  ×  10 cm(2). A water-to-air perturbation factor has been derived as the ratio of total electron (+positron) fluence, integrated over all energies, in a tiny water volume to that in a 'PinPoint 3D-chamber-like' air cavity; for the 0.25  ×  0.25 cm(2) field size the perturbation factors are 1.323 and 2.139 for 6 MV and 15 MV full linac geometries respectively. For the 15 MV full linac geometry for field sizes of 1  ×  1 cm(2) and smaller not only the absolute magnitude but also the 'shape' of the total electron fluence spectrum in the air cavity is significantly different to that in the water 'cavity'. The physics of this 'Bragg-Gray breakdown' is fully explained, making reference to the Fano theorem. For the 15 MV full linac geometry in the 0.25  ×  0.25 cm(2) field the directly computed MC dose ratio, water-to-air, differs by 5% from the product of the Spencer-Attix stopping-power ratio (SPR) and the perturbation factor; this 'difference' is explained by the difference in the shapes of the fluence spectra and is also formulated theoretically. We show that the dimensions of an air-cavity with a perturbation factor within 5% of unity would have to be impractically small in these highly non-equilibrium photon fields. In contrast the dose to water in a 0.25  ×  0.25 cm(2) field derived by multiplying the dose in the single-crystal diamond dosimeter (SCDDo) by the Spencer-Attix ratio is within 2.9% of the dose computed directly in the water voxel for full linac

  17. Breakdown of Bragg-Gray behaviour for low-density detectors under electronic disequilibrium conditions in small megavoltage photon fields.

    PubMed

    Kumar, Sudhir; Fenwick, John D; Underwood, Tracy S A; Deshpande, Deepak D; Scott, Alison J D; Nahum, Alan E

    2015-10-21

    In small photon fields ionisation chambers can exhibit large deviations from Bragg-Gray behaviour; the EGSnrc Monte Carlo (MC) code system has been employed to investigate this 'Bragg-Gray breakdown'. The total electron (+positron) fluence in small water and air cavities in a water phantom has been computed for a full linac beam model as well as for a point source spectrum for 6 MV and 15 MV qualities for field sizes from 0.25  ×  0.25 cm(2) to 10  ×  10 cm(2). A water-to-air perturbation factor has been derived as the ratio of total electron (+positron) fluence, integrated over all energies, in a tiny water volume to that in a 'PinPoint 3D-chamber-like' air cavity; for the 0.25  ×  0.25 cm(2) field size the perturbation factors are 1.323 and 2.139 for 6 MV and 15 MV full linac geometries respectively. For the 15 MV full linac geometry for field sizes of 1  ×  1 cm(2) and smaller not only the absolute magnitude but also the 'shape' of the total electron fluence spectrum in the air cavity is significantly different to that in the water 'cavity'. The physics of this 'Bragg-Gray breakdown' is fully explained, making reference to the Fano theorem. For the 15 MV full linac geometry in the 0.25  ×  0.25 cm(2) field the directly computed MC dose ratio, water-to-air, differs by 5% from the product of the Spencer-Attix stopping-power ratio (SPR) and the perturbation factor; this 'difference' is explained by the difference in the shapes of the fluence spectra and is also formulated theoretically. We show that the dimensions of an air-cavity with a perturbation factor within 5% of unity would have to be impractically small in these highly non-equilibrium photon fields. In contrast the dose to water in a 0.25  ×  0.25 cm(2) field derived by multiplying the dose in the single-crystal diamond dosimeter (SCDDo) by the Spencer-Attix ratio is within 2.9% of the dose computed directly in the water voxel for full linac

  18. Detecting dark matter through dark photons from the Sun: Charged particle signatures

    NASA Astrophysics Data System (ADS)

    Feng, Jonathan L.; Smolinsky, Jordan; Tanedo, Philip

    2016-06-01

    Dark matter may interact with the Standard Model through the kinetic mixing of dark photons, A', with Standard Model photons. Such dark matter will accumulate in the Sun and annihilate into dark photons. The dark photons may then leave the Sun and decay into pairs of charged Standard Model particles that can be detected by the Alpha Magnetic Spectrometer (AMS). The directionality of this "dark sunshine" is distinct from all astrophysical backgrounds, providing an opportunity for unambiguous dark matter discovery by AMS. We perform a complete analysis of this scenario including Sommerfeld enhancements of dark matter annihilation and the effect of the Sun's magnetic field on the signal, and we define a set of cuts to optimize the signal probability. With the three years of data already collected, AMS may discover dark matter with mass 1 TeV ≲mX≲10 TeV , dark photon masses mA'˜O (100 ) MeV , and kinetic mixing parameters 10-11≲ɛ ≲10-8. The proposed search extends beyond existing beam dump and supernova bounds, and it is complementary to direct detection, probing the same region of parameter space.

  19. Electron Photon Interaction Cross Sections

    2014-11-01

    Version 00 The Electron Photon Interaction Cross Sections, EPICS, provides the atomic data needed to perform coupled Electron-Photon transport calculations, to produce accurate macroscopic results, such as energy deposit and dose. Atomic data is provided for elements, Z = 1 to 100, over the energy range 10 eV to 100 GeV; note that nuclear data, such as photo-nuclear, and data for compounds, are not included. All data is in a simple computer independent text formatmore » that is standard and presented to a high precision that can be easily read by computer codes written in any computer language, e.g., C, C++, and FORTRAN. EPICS includes four separate data bases that are designed to be used in combination, these include, • The Evaluated Electron Data Library (EEDL), to describe the interaction of electrons with matter. • The Evaluated Photon Data Library (EPDL), to describe the interaction of photons with matter. • The Evaluated Atomic Data Library (EADL), to describe the emission of electrons and photons back to neutrality following an ionizing event, caused by either electron or photon interactions. • The Evaluated Excitation Data Library (EXDL), to describe the excitation of atoms due to photon interaction. All of these are available in the Extended ENDL format (ENDLX) in which the evaluations were originally performed. The first three are also available in the ENDF format; as yet ENDF does not include formats to handle excitation data (EXDL).« less

  20. Electron Photon Interaction Cross Sections

    SciTech Connect

    Cullen, D. E.

    2014-11-01

    Version 00 The Electron Photon Interaction Cross Sections, EPICS, provides the atomic data needed to perform coupled Electron-Photon transport calculations, to produce accurate macroscopic results, such as energy deposit and dose. Atomic data is provided for elements, Z = 1 to 100, over the energy range 10 eV to 100 GeV; note that nuclear data, such as photo-nuclear, and data for compounds, are not included. All data is in a simple computer independent text format that is standard and presented to a high precision that can be easily read by computer codes written in any computer language, e.g., C, C++, and FORTRAN. EPICS includes four separate data bases that are designed to be used in combination, these include, • The Evaluated Electron Data Library (EEDL), to describe the interaction of electrons with matter. • The Evaluated Photon Data Library (EPDL), to describe the interaction of photons with matter. • The Evaluated Atomic Data Library (EADL), to describe the emission of electrons and photons back to neutrality following an ionizing event, caused by either electron or photon interactions. • The Evaluated Excitation Data Library (EXDL), to describe the excitation of atoms due to photon interaction. All of these are available in the Extended ENDL format (ENDLX) in which the evaluations were originally performed. The first three are also available in the ENDF format; as yet ENDF does not include formats to handle excitation data (EXDL).

  1. Photonic Landau levels on cones

    NASA Astrophysics Data System (ADS)

    Schine, Nathan; Ryou, Albert; Gromov, Andrey; Sommer, Ariel; Simon, Jonathan

    2016-05-01

    We present the first experimental realization of a bulk magnetic field for optical photons. By using a non-planar ring resonator, we induce an image rotation on each round trip through the resonator. This results in a Coriolis/Lorentz force and a centrifugal anticonfining force, the latter of which is cancelled by mirror curvature. Using a digital micromirror device to control both amplitude and phase, we inject arbitrary optical modes into our resonator. Spatial- and energy- resolved spectroscopy tracks photonic eigenstates as residual trapping is reduced, and we observe photonic Landau levels as the eigenstates become degenerate. We show that there is a conical geometry of the resulting manifold for photon dynamics and present a measurement of the local density of states that is consistent with Landau levels on a cone. While our work already demonstrates an integer quantum Hall material composed of photons, we have ensured compatibility with strong photon-photon interactions, which will allow quantum optical studies of entanglement and correlation in manybody systems including fractional quantum Hall fluids.

  2. Investigation of variance reduction techniques for Monte Carlo photon dose calculation using XVMC

    NASA Astrophysics Data System (ADS)

    Kawrakow, Iwan; Fippel, Matthias

    2000-08-01

    Several variance reduction techniques, such as photon splitting, electron history repetition, Russian roulette and the use of quasi-random numbers are investigated and shown to significantly improve the efficiency of the recently developed XVMC Monte Carlo code for photon beams in radiation therapy. It is demonstrated that it is possible to further improve the efficiency by optimizing transport parameters such as electron energy cut-off, maximum electron energy step size, photon energy cut-off and a cut-off for kerma approximation, without loss of calculation accuracy. These methods increase the efficiency by a factor of up to 10 compared with the initial XVMC ray-tracing technique or a factor of 50 to 80 compared with EGS4/PRESTA. Therefore, a common treatment plan (6 MV photons, 10×10 cm2 field size, 5 mm voxel resolution, 1% statistical uncertainty) can be calculated within 7 min using a single CPU 500 MHz personal computer. If the requirement on the statistical uncertainty is relaxed to 2%, the calculation time will be less than 2 min. In addition, a technique is presented which allows for the quantitative comparison of Monte Carlo calculated dose distributions and the separation of systematic and statistical errors. Employing this technique it is shown that XVMC calculations agree with EGSnrc on a sub-per cent level for simulations in the energy and material range of interest for radiation therapy.

  3. Zero photon dissociation of CS2+ in intense ultrashort laser pulses

    NASA Astrophysics Data System (ADS)

    Severt, Travis; Betsch, K. J.; Zohrabi, M.; Ablikim, U.; Jochim, Bethany; Carnes, K. D.; Esry, B. D.; Ben-Itzhak, I.

    2013-05-01

    We measured the dissociation of a CS2+ molecular ion beam in intense laser pulses (<50 fs, <1015 W/cm2), focusing on the zero photon dissociation (ZPD) and above threshold dissociation (ATD) mechanisms. The ZPD mechanism leads to dissociation with the net absorption of zero photons in a strong field. The present work extends the idea of ZPD to more complex molecules than the H2+ discussed in literature. Preliminary data suggests that ZPD is larger than ATD for CS2+ --> C+ + S+. We speculate that a pump-dump process occurs whereby the vibrational wavepacket in the electronic ground state of CS2+ is pumped into the electronic first excited state's continuum by a single photon during the laser pulse. Once this continuum vibrational wavepacket passes the potential barrier in the ground electronic potential, the emission of a second photon is stimulated by the same laser pulse, most likely when the wavepacket moves through the internuclear distance where the two electronic states are in resonance with the driving field. A comparison is made to ZPD and ATD in the isovalent CO2+ species. Curiously, ATD is the favored mechanism in CO2+. The underlying molecular structure and dynamics determining this preference will be discussed. Supported by Chemical Sciences, Geosciences, and Biosciences Division, Office of Basic Energy Sciences, Office of Science, U.S. Department of Energy.

  4. Nonlinear Interaction of the Beat-Photon Beams with the Brain Neurocenters: Laser Neurophysics

    NASA Astrophysics Data System (ADS)

    Stefan, V. Alexander

    2010-03-01

    I propose a novel mechanism for laser-brain interaction: Nonlinear interaction of ultrashort pulses of beat-photon, (φ1-- φ2), or double-photon, (φ1+φ2), footnotetextMaria Goeppert-Mayer, "Uber Elementarakte mit zwei Quantenspr"ungen, Ann Phys 9, 273, 95. (1931). beams with the corrupted brain neurocenters, causing a particular neurological disease. The open-scull cerebral tissue can be irradiated with the beat-photon pulses in the range of several 100s fs, with the laser irradiances in the range of a few mW/cm^2, repetition rate of a few 100s Hz, and in the frequency range of 700-1300nm generated in the beat-wave driven free electron laser.footnotetextV. Alexander Stefan, The Interaction of Photon Beams with the DNA Molecules: Genomic Medical Physics. American Physical Society, 2009 APS March Meeting, March 16-20, 2009, abstract #K1.276; V. Stefan, B. I. Cohen, and C. Joshi, Nonlinear Mixing of Electromagnetic Waves in Plasmas Science 27 January 1989:Vol. 243. no. 4890, pp. 494 -- 500 (January 1989). This method may prove to be an effective mechanism in the treatment of neurological diseases: Parkinson's, Lou Gehrig's, and others.

  5. Review of photon interaction cross section data in the medical and biological context.

    PubMed

    Hubbell, J H

    1999-01-01

    The probability of a photon (x-ray, gamma-ray, bremsstrahlung, etc) of a given energy E undergoing absorption or scattering when traversing a layer of material Z can be expressed quantitatively in terms of a linear attenuation coefficient mu (cm(-1)). Since mu is dependent on the material's density, rho (g cm(-3)), which can be variable, the quantity usually tabulated is the mass attenuation coefficient mu/rho (cm2 g(-1)) in which the dependence on the density has been removed. Mu/rho, in turn, can be obtained as the sum of the different types of possible interactions of photons with atoms of the material. For photon energies below 1 MeV the major interaction processes to be considered are incoherent (Compton) scattering, coherent (Rayleigh) scattering and atomic photoeffect absorption. Above 1 MeV one must also include nuclear-field pair production and atomic-field (triplet) production, and above 5 MeV one in principle should include photonuclear absorption, although the latter is neglected in data tabulations up to the present time. This review includes a selective history of measurements and theory relating to mu/rho from the turn of the century up to the present time, and is intended to provide a basis for further calculations and critical tabulations of photon cross section data, particularly as required by users in radiation medicine and biology. The mass energy-absorption coefficient mu(en)/rho is also briefly discussed.

  6. Quantum imaging with undetected photons.

    PubMed

    Lemos, Gabriela Barreto; Borish, Victoria; Cole, Garrett D; Ramelow, Sven; Lapkiewicz, Radek; Zeilinger, Anton

    2014-08-28

    Information is central to quantum mechanics. In particular, quantum interference occurs only if there exists no information to distinguish between the superposed states. The mere possibility of obtaining information that could distinguish between overlapping states inhibits quantum interference. Here we introduce and experimentally demonstrate a quantum imaging concept based on induced coherence without induced emission. Our experiment uses two separate down-conversion nonlinear crystals (numbered NL1 and NL2), each illuminated by the same pump laser, creating one pair of photons (denoted idler and signal). If the photon pair is created in NL1, one photon (the idler) passes through the object to be imaged and is overlapped with the idler amplitude created in NL2, its source thus being undefined. Interference of the signal amplitudes coming from the two crystals then reveals the image of the object. The photons that pass through the imaged object (idler photons from NL1) are never detected, while we obtain images exclusively with the signal photons (from NL1 and NL2), which do not interact with the object. Our experiment is fundamentally different from previous quantum imaging techniques, such as interaction-free imaging or ghost imaging, because now the photons used to illuminate the object do not have to be detected at all and no coincidence detection is necessary. This enables the probe wavelength to be chosen in a range for which suitable detectors are not available. To illustrate this, we show images of objects that are either opaque or invisible to the detected photons. Our experiment is a prototype in quantum information--knowledge can be extracted by, and about, a photon that is never detected. PMID:25164751

  7. Single photon source characterization with a superconducting single photon detector.

    PubMed

    Hadfield, Robert H; Stevens, Martin J; Gruber, Steven S; Miller, Aaron J; Schwall, Robert E; Mirin, Richard P; Nam, Sae Woo

    2005-12-26

    Superconducting single photon detectors (SSPD) based on nanopatterned niobium nitride wires offer single photon counting at fast rates, low jitter, and low dark counts, from visible wavelengths well into the infrared. We demonstrate the first use of an SSPD, packaged in a commercial cryocooler, for single photon source characterization. The source is an optically pumped, microcavity-coupled InGaAs quantum dot, emitting single photons at 902 nm. The SSPD replaces the second silicon Avalanche Photodiode (APD) in a Hanbury-Brown Twiss interferometer measurement of the source second-order correlation function, g(2)( ?). The detection efficiency of the superconducting detector system is >2 % (coupling losses included). The SSPD system electronics jitter is 170 ps, versus 550 ps for the APD unit, allowing the source spontaneous emission lifetime to be measured with improved resolution.

  8. Spherical colloidal photonic crystals.

    PubMed

    Zhao, Yuanjin; Shang, Luoran; Cheng, Yao; Gu, Zhongze

    2014-12-16

    CONSPECTUS: Colloidal photonic crystals (PhCs), periodically arranged monodisperse nanoparticles, have emerged as one of the most promising materials for light manipulation because of their photonic band gaps (PBGs), which affect photons in a manner similar to the effect of semiconductor energy band gaps on electrons. The PBGs arise due to the periodic modulation of the refractive index between the building nanoparticles and the surrounding medium in space with subwavelength period. This leads to light with certain wavelengths or frequencies located in the PBG being prohibited from propagating. Because of this special property, the fabrication and application of colloidal PhCs have attracted increasing interest from researchers. The most simple and economical method for fabrication of colloidal PhCs is the bottom-up approach of nanoparticle self-assembly. Common colloidal PhCs from this approach in nature are gem opals, which are made from the ordered assembly and deposition of spherical silica nanoparticles after years of siliceous sedimentation and compression. Besides naturally occurring opals, a variety of manmade colloidal PhCs with thin film or bulk morphology have also been developed. In principle, because of the effect of Bragg diffraction, these PhC materials show different structural colors when observed from different angles, resulting in brilliant colors and important applications. However, this angle dependence is disadvantageous for the construction of some optical materials and devices in which wide viewing angles are desired. Recently, a series of colloidal PhC materials with spherical macroscopic morphology have been created. Because of their spherical symmetry, the PBGs of spherical colloidal PhCs are independent of rotation under illumination of the surface at a fixed incident angle of the light, broadening the perspective of their applications. Based on droplet templates containing colloidal nanoparticles, these spherical colloidal PhCs can be

  9. Random photonic crystal optical memory

    NASA Astrophysics Data System (ADS)

    Wirth Lima, A., Jr.; Sombra, A. S. B.

    2012-10-01

    Currently, optical cross-connects working on wavelength division multiplexing systems are based on optical fiber delay lines buffering. We designed and analyzed a novel photonic crystal optical memory, which replaces the fiber delay lines of the current optical cross-connect buffer. Optical buffering systems based on random photonic crystal optical memory have similar behavior to the electronic buffering systems based on electronic RAM memory. In this paper, we show that OXCs working with optical buffering based on random photonic crystal optical memories provides better performance than the current optical cross-connects.

  10. Slow Images and Entangled Photons

    SciTech Connect

    Swordy, Simon

    2007-06-20

    I will discuss some recent experiments using slow light and entangled photons. We recently showed that it was possible to map a two dimensional image onto very low light level signals, slow them down in a hot atomic vapor while preserving the amplitude and phase of the images. If time remains, I will discuss some of our recent work with time-energy entangled photons for quantum cryptography. We were able to show that we could have a measurable state space of over 1000 states for a single pair of entangled photons in fiber.

  11. Configurable silicon photonic crystal waveguides

    NASA Astrophysics Data System (ADS)

    Prorok, Stefan; Petrov, Alexander; Eich, Manfred; Luo, Jingdong; Jen, Alex K.-Y.

    2013-12-01

    In this Letter, we demonstrate that the mode cut off of a photonic crystal waveguide can be trimmed with high accuracy by electron beam bleaching of a chromophore doped polymer cladding. Using this method, configurable waveguides are realized, which allow for spatially resolved changes of the photonic crystal's effective lattice constant as small as 7.6 pm. We show three different examples how to take advantage of configurable photonic crystal waveguides: Shifting of the complete transmission spectrum, definition of cavities with high quality factor, and tuning of existing cavities.

  12. Partial confinement photonic crystal waveguides

    SciTech Connect

    Saini, S.; Hong, C.-Y.; Pfaff, N.; Kimerling, L. C.; Michel, J.

    2008-12-29

    One-dimensional photonic crystal waveguides with an incomplete photonic band gap are modeled and proposed for an integration application that exploits their property of partial angular confinement. Planar apodized photonic crystal structures are deposited by plasma enhanced chemical vapor deposition and characterized by reflectivity as a function of angle and polarization, validating a partial confinement design for light at 850 nm wavelength. Partial confinement identifies an approach for tailoring waveguide properties by the exploitation of conformal film deposition over a substrate with angularly dependent topology. An application for an optoelectronic transceiver is demonstrated.

  13. Summary of Lepton Photon 2011

    SciTech Connect

    Peskin, Michael E.; /SLAC

    2012-03-14

    In this lecture, I summarize developments presented at the Lepton Photon 2011 conference and give my perspective on the current situation in high-energy physics. I am grateful to the organizers of Lepton Photon 2011 for providing us a very pleasant and simulating week in Mumbai. This year's Lepton Photon conference has covered the full range of subjects that fall within the scope of high-energy physics, including connections to cosmology, nuclear physics, and atomic physics. The experiments that were discussed detect particles ranging in energy from radio frequencies to EeV.

  14. Manufacturing method of photonic crystal

    SciTech Connect

    Park, In Sung; Lee, Tae Ho; Ahn, Jin Ho; Biswas, Rana; Constant, Kristen P.; Ho, Kai-Ming; Lee, Jae-Hwang

    2013-01-29

    A manufacturing method of a photonic crystal is provided. In the method, a high-refractive-index material is conformally deposited on an exposed portion of a periodic template composed of a low-refractive-index material by an atomic layer deposition process so that a difference in refractive indices or dielectric constants between the template and adjacent air becomes greater, which makes it possible to form a three-dimensional photonic crystal having a superior photonic bandgap. Herein, the three-dimensional structure may be prepared by a layer-by-layer method.

  15. Multicolor photonic crystal laser array

    SciTech Connect

    Wright, Jeremy B; Brener, Igal; Subramania, Ganapathi S; Wang, George T; Li, Qiming

    2015-04-28

    A multicolor photonic crystal laser array comprises pixels of monolithically grown gain sections each with a different emission center wavelength. As an example, two-dimensional surface-emitting photonic crystal lasers comprising broad gain-bandwidth III-nitride multiple quantum well axial heterostructures were fabricated using a novel top-down nanowire fabrication method. Single-mode lasing was obtained in the blue-violet spectral region with 60 nm of tuning (or 16% of the nominal center wavelength) that was determined purely by the photonic crystal geometry. This approach can be extended to cover the entire visible spectrum.

  16. Configurable silicon photonic crystal waveguides

    SciTech Connect

    Prorok, Stefan; Petrov, Alexander; Eich, Manfred; Luo, Jingdong; Jen, Alex K.-Y.

    2013-12-23

    In this Letter, we demonstrate that the mode cut off of a photonic crystal waveguide can be trimmed with high accuracy by electron beam bleaching of a chromophore doped polymer cladding. Using this method, configurable waveguides are realized, which allow for spatially resolved changes of the photonic crystal's effective lattice constant as small as 7.6 pm. We show three different examples how to take advantage of configurable photonic crystal waveguides: Shifting of the complete transmission spectrum, definition of cavities with high quality factor, and tuning of existing cavities.

  17. Ultralow loss, high Q, four port resonant couplers for quantum optics and photonics.

    PubMed

    Rokhsari, H; Vahala, K J

    2004-06-25

    We demonstrate a low-loss, optical four port resonant coupler (add-drop geometry), using ultrahigh Q (>10(8)) toroidal microcavities. Different regimes of operation are investigated by variation of coupling between resonator and fiber taper waveguides. As a result, waveguide-to-waveguide power transfer efficiency of 93% (0.3 dB loss) and nonresonant insertion loss of 0.02% (<0.001 dB) for narrow bandwidth (57 MHz) four port couplers are achieved in this work. The combination of low-loss, fiber compatibility, and wafer-scale design would be suitable for a variety of applications ranging from quantum optics to photonic networks.

  18. Ultrafast optical switching using photonic molecules in photonic crystal waveguides.

    PubMed

    Zhao, Yanhui; Qian, Chenjiang; Qiu, Kangsheng; Gao, Yunan; Xu, Xiulai

    2015-04-01

    We study the coupling between photonic molecules and waveguides in photonic crystal slab structures using finite-difference time-domain method and coupled mode theory. In a photonic molecule with two cavities, the coupling of cavity modes results in two super-modes with symmetric and anti-symmetric field distributions. When two super-modes are excited simultaneously, the energy of electric field oscillates between the two cavities. To excite and probe the energy oscillation, we integrate photonic molecule with two photonic crystal waveguides. In coupled structure, we find that the quality factors of two super-modes might be different because of different field distributions of super-modes. After optimizing the radii of air holes between two cavities of photonic molecule, nearly equal quality factors of two super-modes are achieved, and coupling strengths between the waveguide modes and two super-modes are almost the same. In this case, complete energy oscillations between two cavities can be obtained with a pumping source in one waveguide, which can be read out by another waveguide. Finally, we demonstrate that the designed structure can be used for ultrafast optical switching with a time scale of a few picoseconds.

  19. EDITORIAL: Photonic terahertz technology

    NASA Astrophysics Data System (ADS)

    Lisauskas, Alvydas; Löffler, Torsten; Roskos, Hartmut G.

    2005-07-01

    In recent years, when reading newspapers and journals or watching TV, one has been able to find feature presentations dealing with the prospects of terahertz (THz) technology and its potential impact on market applications. THz technology aims to fill the THz gap in the electro-magnetic spectrum in order to make the THz frequency regime, which spans the two orders of magnitude from 100 GHz to 10 THz, accessible for applications. From the lower-frequency side, electronics keeps pushing upwards, while photonic approaches gradually improve our technological options at higher frequencies. The popular interest reflects the considerable advances in research in the THz field, and it is mainly advances in the photonic branch, with the highlight being the development of the THz quantum cascade laser, which in recent years have caught the imagination of the public, and of potential users and investors. This special issue of Semiconductor Science and Technology provides an overview of key scientific developments which currently represent the cutting edge of THz photonic technology. In order to be clear about the implications, we should define exactly what we mean by 'THz photonic technology', or synonymously 'THz photonics'. It is characterized by the way in which THz radiation (or a guided THz wave) is generated, namely by the use of lasers. This may be done in one of two fundamentally different schemes: (i) by laser action in the terahertz frequency range itself (THz lasers), or (ii) by down-conversion processes (photomixing) involving the radiation of lasers which operate in the visible, near-infrared or infrared spectral ranges, either in pulsed or continuous-wave mode. The field of THz photonics has grown so considerably that it is out of the question to cover all its aspects in a single special issue of a journal. We have elected, instead, to focus our attention on two types of development with a potentially strong impact on the THz field: first, on significant advances

  20. Pushing the Photon Limit: Nanoantennas Increase Maximal Photon Stream and Total Photon Number

    PubMed Central

    2016-01-01

    Nanoantennas are well-known for their effective role in fluorescence enhancement, both in excitation and emission. Enhancements of 3–4 orders of magnitude have been reported. Yet in practice, the photon emission is limited by saturation due to the time that a molecule spends in singlet and especially triplet excited states. The maximal photon stream restricts the attainable enhancement. Furthermore, the total number of photons emitted is limited by photobleaching. The limited brightness and observation time are a drawback for applications, especially in biology. Here we challenge this photon limit, showing that nanoantennas can actually increase both saturation intensity and photostability. So far, this limit-shifting role of nanoantennas has hardly been explored. Specifically, we demonstrate that single light-harvesting complexes, under saturating excitation conditions, show over a 50-fold antenna-enhanced photon emission stream, with 10-fold more total photons, up to 108 detected photons, before photobleaching. This work shows yet another facet of the great potential of nanoantennas in the world of single-molecule biology. PMID:27082249

  1. Radiation reaction and resulting photon emission from laser-irradiated solid targets

    NASA Astrophysics Data System (ADS)

    Stark, David; Arefiev, Alexey; Hegelich, Manuel

    2014-10-01

    Once completed, an ongoing upgrade of the Texas-PW laser system would allow us to achieve on-target laser intensities of up to 5 ×1022 W/cm2. As experimental confirmation of the radiation reaction force and the variety of models describing it remains a challenge, here we present a scenario that would enable us to observe the effect by detecting the resulting photon emission. A laser with our planned intensity could accelerate an electron to hundreds of MeV, but the radiation reaction and thus the photon emission would be relatively weak if the electron co-propagates with the wave. We consider a solid density target irradiated by a laser beam so that strong fields are generated due to charge separation. These fields can alter the electron trajectories, leading to strong radiation reaction and photon emission in the focal spot. Simulating this interaction using the particle-in-cell code EPOCH, we perform a target density scan that allows us to optimize the fraction of the laser energy converted into photons and to determine the photon spectrum. Knowing the spectrum and the angular emission is critical for measurements in the lab, since these photons must be distinguished from those from other processes. We use HPC resources from the Texas Advanced Computing Center. This work is supported by DOD-Air Force Contract No. FA9550-14-1-0045, US DOE Contract No. DE-FG02-04ER54742, and DOE SCGF by ORISE-ORAU under Contract No. DE-AC05-06OR23100.

  2. The Photon Underproduction Crisis

    NASA Astrophysics Data System (ADS)

    Kollmeier, Juna A.; Weinberg, David H.; Oppenheimer, Benjamin D.; Haardt, Francesco; Katz, Neal; Davé, Romeel; Fardal, Mark; Madau, Piero; Danforth, Charles; Ford, Amanda B.; Peeples, Molly S.; McEwen, Joseph

    2014-07-01

    We examine the statistics of the low-redshift Lyα forest from smoothed particle hydrodynamic simulations in light of recent improvements in the estimated evolution of the cosmic ultraviolet background (UVB) and recent observations from the Cosmic Origins Spectrograph (COS). We find that the value of the metagalactic photoionization rate (ΓHI) required by our simulations to match the observed properties of the low-redshift Lyα forest is a factor of five larger than the value predicted by state-of-the art models for the evolution of this quantity. This mismatch in ΓHI results in the mean flux decrement of the Lyα forest being overpredicted by at least a factor of two (a 10σ discrepancy with observations) and a column density distribution of Lyα forest absorbers systematically and significantly elevated compared to observations over nearly two decades in column density. We examine potential resolutions to this mismatch and find that either conventional sources of ionizing photons (galaxies and quasars) must contribute considerably more than current observational estimates or our theoretical understanding of the low-redshift universe is in need of substantial revision.

  3. Anti-photon

    NASA Astrophysics Data System (ADS)

    Lamb, W. E.

    1995-02-01

    It should be apparent from the title of this article that the author does not like the use of the word “photon”, which dates from 1926. In his view, there is no such thing as a photon. Only a comedy of errors and historical accidents led to its popularity among physicists and optical scientists. I admit that the word is short and convenient. Its use is also habit forming. Similarly, one might find it convenient to speak of the “aether” or “vacuum” to stand for empty space, even if no such thing existed. There are very good substitute words for “photon”, (e.g., “radiation” or “light”), and for “photonics” (e.g., “optics” or “quantum optics”). Similar objections are possible to use of the word “phonon”, which dates from 1932. Objects like electrons, neutrinos of finite rest mass, or helium atoms can, under suitable conditions, be considered to be particles, since their theories then have viable non-relativistic and non-quantum limits. This paper outlines the main features of the quantum theory of radiation and indicates how they can be used to treat problems in quantum optics.

  4. Photonic MEMS switch applications

    NASA Astrophysics Data System (ADS)

    Husain, Anis

    2001-07-01

    As carriers and service providers continue their quest for profitable network solutions, they have shifted their focus from raw bandwidth to rapid provisioning, delivery and management of revenue generating services. Inherently transparent to data rate the transmission wavelength and data format, MEMS add scalability, reliability, low power and compact size providing flexible solutions to the management and/or fiber channels in long haul, metro, and access networks. MEMS based photonic switches have gone from the lab to commercial availability and are now currently in carrier trials and volume production. 2D MEMS switches offer low up-front deployment costs while remaining scalable to large arrays. They allow for transparent, native protocol transmission. 2D switches enable rapid service turn-up and management for many existing and emerging revenue rich services such as storage connectivity, optical Ethernet, wavelength leasing and optical VPN. As the network services evolve, the larger 3D MEMS switches, which provide greater scalability and flexibility, will become economically viable to serve the ever-increasing needs.

  5. THE PHOTON UNDERPRODUCTION CRISIS

    SciTech Connect

    Kollmeier, Juna A.; Weinberg, David H.; McEwen, Joseph; Oppenheimer, Benjamin D.; Danforth, Charles; Haardt, Francesco; Katz, Neal; Fardal, Mark; Davé, Romeel; Madau, Piero; Ford, Amanda B.; Peeples, Molly S.

    2014-07-10

    We examine the statistics of the low-redshift Lyα forest from smoothed particle hydrodynamic simulations in light of recent improvements in the estimated evolution of the cosmic ultraviolet background (UVB) and recent observations from the Cosmic Origins Spectrograph (COS). We find that the value of the metagalactic photoionization rate (Γ{sub HI}) required by our simulations to match the observed properties of the low-redshift Lyα forest is a factor of five larger than the value predicted by state-of-the art models for the evolution of this quantity. This mismatch in Γ{sub HI} results in the mean flux decrement of the Lyα forest being overpredicted by at least a factor of two (a 10σ discrepancy with observations) and a column density distribution of Lyα forest absorbers systematically and significantly elevated compared to observations over nearly two decades in column density. We examine potential resolutions to this mismatch and find that either conventional sources of ionizing photons (galaxies and quasars) must contribute considerably more than current observational estimates or our theoretical understanding of the low-redshift universe is in need of substantial revision.

  6. Investigation of internal friction in fused quartz, steel, Plexiglass, and Westerly granite from 0.01 to 1.00 Hertz at 10- 8 to 10-7 strain amplitude.

    USGS Publications Warehouse

    Hsi-Ping, Liu; Peselnick, L.

    1983-01-01

    A detailed evaluation on the method of internal friction measurement by the stress-strain hysteresis loop method from 0.01 to 1 Hz at 10-8-10-7 strain amplitude and 23.9oC is presented. Significant systematic errors in relative phase measurement can result from convex end surfaces of the sample and stress sensor and from end surface irregularities such as nicks and asperities. Preparation of concave end surfaces polished to optical smoothness having a radius of curvature >3.6X104 cm reduces the systematic error in relative phase measurements to <(5.5+ or -2.2)X10-4 radians. -from Authors

  7. Towards four-dimensional photonics

    NASA Astrophysics Data System (ADS)

    Price, Hannah M.; Ozawa, Tomoki; Goldman, Nathan; Zilberberg, Oded; Carusotto, Iacopo

    2016-03-01

    Recent advances in silicon ring-resonator arrays have stimulated the development of topological lattices for photons, with potential applications in integrated photonic devices. Taking inspiration from ultracold atoms, we propose how such arrays can be extended into an additional synthetic dimension by coupling together the different modes of each ring resonator.1 In this way, a 1D resonator chain can become an effective 2D system, while a 3D resonator array can be exploited as a 4D photonic lattice. As an example of the power of this approach, we discuss how to experimentally realise an optical analogue of the 4D quantum Hall effect for the first time. This opens up the way towards the exploration of higher-dimensional lattices in integrated photonics.

  8. Photon Counting - One More Time

    NASA Astrophysics Data System (ADS)

    Stanton, Richard H.

    2012-05-01

    Photon counting has been around for more than 60 years, and has been available to amateurs for most of that time. In most cases single photons are detected using photomultiplier tubes, "old technology" that became available after the Second World War. But over the last couple of decades the perfection of CCD devices has given amateurs the ability to perform accurate photometry with modest telescopes. Is there any reason to still count photons? This paper discusses some of the strengths of current photon counting technology, particularly relating to the search for fast optical transients. Technology advances in counters and photomultiplier modules are briefly mentioned. Illustrative data are presented including FFT analysis of bright star photometry and a technique for finding optical pulses in a large file of noisy data. This latter technique is shown to enable the discovery of a possible optical flare on the polar variable AM Her.

  9. Femtosecond Photon-Counting Receiver

    NASA Technical Reports Server (NTRS)

    Krainak, Michael A.; Rambo, Timothy M.; Yang, Guangning; Lu, Wei; Numata, Kenji

    2016-01-01

    An optical correlation receiver is described that provides ultra-precise distance and/or time/pulse-width measurements even for weak (single photons) and short (femtosecond) optical signals. A new type of optical correlation receiver uses a fourth-order (intensity) interferometer to provide micron distance measurements even for weak (single photons) and short (femtosecond) optical signals. The optical correlator uses a low-noise-integrating detector that can resolve photon number. The correlation (range as a function of path delay) is calculated from the variance of the photon number of the difference of the optical signals on the two detectors. Our preliminary proof-of principle data (using a short-pulse diode laser transmitter) demonstrates tens of microns precision.

  10. Photonic electromagnetic field sensor apparatus

    NASA Astrophysics Data System (ADS)

    Hilliard, Donald P.; Mensa, Dean L.

    1993-07-01

    An electromagnetic field sensor apparatus which measures the field strength and phase of an incident electromagnetic field as well as the angle of arrival of an incident electromagnetic field is presented. The electromagnetic field sensor apparatus comprises a Luneberg lens which focuses an incoming planar electromagnetic wave entering on one side of the Luneberg lens onto a point on the opposite side of the lens. A photonic sensor is positioned on the Luneberg lens at the point upon which the electromagnetic wave is focused. A light source is located along an optical path which passes through the photonic sensor for transmitting polarized light through the sensor. The photonic sensor modulates the polarized light passing therethrough when the photonic sensor detects the incident electromagnetic wave.

  11. Photonic electromagnetic field sensor apparatus

    NASA Astrophysics Data System (ADS)

    Hilliard, Donald P.; Mensa, Dean L.

    1993-09-01

    An electromagnetic field sensor apparatus which measures the amplitude, phase, frequency and polarization of an incoming electromagnetic field as well as the angle of arrival of an incident electromagnetic field is introduced. A Luneberg lens focuses an incoming electromagnetic wave entering on one side of the Luneberg lens onto a point on the opposite side of the lens. A pair of photonic sensor which may be electro-optic modulators or Pockel cells are positioned on the Luneberg lens at the point upon which the incident electromagnetic wave is focused. The sensing axis of one of the electro-optic modulators is perpendicular to the sensing axis of the other electro-optic modulator. Polarized light is provided to each photonic sensor along an optical path which passes through the sensor. Each photonic sensor modulates the polarized light passing therethrough when the photonic sensor detects the incident electromagnetic wave.

  12. Photon scattering in muon collisions.

    SciTech Connect

    Klasen, M.

    1997-12-18

    The authors estimate the benefit of muon colliders for photon physics. They calculate the rate at which photons are emitted from muon beams in different production mechanisms. Bremsstrahlung is reduced, beamstrahlung disappears, and laser backscattering suffers from a bad conversion of the incoming to the outgoing photon beam in addition to requiring very short wavelengths. As a consequence, the cross sections for jet photoproduction in {mu}p and {mu}{sup +} {mu}{sup {minus}} collisions are reduced by factors of 2.2 and 5 compared to ep and e{sup +} e{sup {minus}} machines. However, the cross sections remain sizable and measurable giving access to the photon and proton parton densities down to x values of 10{sup {minus}3} to 10{sup {minus}4}.

  13. National Photonics Skills Standard for Technicians.

    ERIC Educational Resources Information Center

    Center for Occupational Research and Development, Inc., Waco, TX.

    This document defines "photonics" as the generation, manipulation, transport, detection, and use of light information and energy whose quantum unit is the photon. The range of applications of photonics extends from energy generation to detection to communication and information processing. Photonics is at the heart of today's communication…

  14. Experimental study of photonic crystal triangular lattices

    NASA Astrophysics Data System (ADS)

    Qin, Ruhu; Qin, Bo; Jin, Chongjun

    1999-06-01

    Triangular lattice photonic crystal behaving in the electromagnetic zones constructed from fused silica cylinders in styrofoam is fabricated. The transmission spectra of the photonic crystal with and without defects are measured. On this basis, the defect modes of photonic crystal were studied, and the potential applications of the photonic crystal are discussed.

  15. Photon final states at the Tevatron

    SciTech Connect

    Campanelli, Mario; /University Coll. London

    2008-04-01

    The authors present here several recent measurements involving associate production of photons and jets at the Tevatron. In particular, inclusive photon + met from D0, and photon + b-jets and photon + b-jet + leptons + MET from CDF are described in some detail. These measurements offer a good test of QCD predictions in rather complex final states.

  16. Few-photon heterodyne spectroscopy

    NASA Astrophysics Data System (ADS)

    Amaral, G. C.; Ferreira da Silva, T.; Temporão, G. P.; von der Weid, J. P.

    2016-04-01

    We perform a high resolution Fourier Transform Spectroscopy of optical sources in the few-photon regime based on the phenomenon of two-photon interference in a beam splitter. From the heterodyne interferogram between test and reference sources it is possible to obtain the spectrum of the test source relative to that of the reference. The method proves to be a useful asset for spectral characterization of faint optical sources below the range covered by classical heterodyne beating techniques.

  17. Recent progress in medical photonics

    NASA Astrophysics Data System (ADS)

    Xie, Shusen; Li, Hui; Li, Buhong

    2009-06-01

    The field of medical photonics is rapidly expanding, and a wide variety of optical technologies and instruments have recently been developed for diagnostic, therapeutic and basic science applications in medicine. This review presents the recent advances and application of medical photonics, and the obtained results from our laboratory are highlighted. Finally, the challenges and future prospects for the transition from technological exploration to clinical studies are discussed.

  18. Microresonator and associated method for producing and controlling photonic signals with a photonic bandgap delay apparatus

    NASA Technical Reports Server (NTRS)

    Fork, Richard Lynn (Inventor); Jones, Darryl Keith (Inventor); Keys, Andrew Scott (Inventor)

    2000-01-01

    By applying a photonic signal to a microresonator that includes a photonic bandgap delay apparatus having a photonic band edge transmission resonance at the frequency of the photonic signal, the microresonator imparts a predetermined delay to the photonic signal. The photonic bandgap delay apparatus also preferably has a photonic band edge transmission resonance bandwidth which is at least as wide as the bandwidth of the photonic signal such that a uniform delay is imparted over the entire bandwidth of the photonic signal. The microresonator also includes a microresonator cavity, typically defined by a pair of switchable mirrors, within which the photonic bandgap delay apparatus is disposed. By requiring the photonic signal to oscillate within the microresonator cavity so as to pass through the photonic bandgap delay apparatus several times, the microresonator can controllably impart an adjustable delay to the photonic signal.

  19. Mechanically tunable photonic crystal lens

    NASA Astrophysics Data System (ADS)

    Cui, Y.; Tamma, V. A.; Lee, J.-B.; Park, W.

    2010-08-01

    We designed, fabricated and characterized MEMS-enabled mechanically-tunable photonic crystal lens comprised of 2D photonic crystal and symmetrical electro-thermal actuators. The 2D photonic crystal was made of a honeycomb-lattice of 340 nm thick, 260 nm diameter high-index silicon rods embedded in low-index 10 μm thick SU-8 cladding. Silicon input waveguide and deflection block were also fabricated for light in-coupling and monitoring of focused spot size, respectively. When actuated, the electro-thermal actuators induced mechanical strain which changed the lattice constant of the photonic crystal and consequently modified the photonic band structure. This in turn modified the focal-length of the photonic crystal lens. The fabricated device was characterized using a tunable laser (1400~1602 nm) and an infrared camera during actuation. At the wavelength of 1450 nm, the lateral light spot size observed at the deflection block gradually decreased 40%, as applied current increased from 0 to 0.7 A, indicating changes in focal length in response to the mechanical stretching.

  20. Ultra-broadband photonic internet

    NASA Astrophysics Data System (ADS)

    Romaniuk, Ryszard S.

    2011-06-01

    In this paper, there is presented a review of our today's understanding of the ultimately broadband photonic Internet. A simple calculation is presented showing the estimate of the throughput of the core photonic network branches. Optoelectronic components, circuits, systems and signals, together with analogous electronic entities and common software layers, are building blocks of the contemporary Internet. Participation of photonics in development of the physical layer in the future Internet will probably increase. The photonics leads now to a better usage of the available bandwidth (increase of the spectral efficiency measured in Bit/s/Hz), increase in the transmission rate (from Gbps, via Tbps up to probably Pbps), increase in the transmission distance without signal regeneration (in distortion compensated active optical cables), increase in energy/power efficiency measured in W/Gbps, etc. Photonics may lead, in the future, to fully transparent optical networks and, thus, to essential increase in bandwidth and network reliability. It is expected that photonics (with biochemistry, electronics and mechatronics) may build psychological and physiological interface for humans to the future global network. The following optical signal multiplexing methods were considered, which are possible without O/E/O conversion: TDM-OTDM, FDM-CO-OFDM, OCDM-OCDMA, WDM-DWDM.

  1. Spatial filtering with photonic crystals

    SciTech Connect

    Maigyte, Lina; Staliunas, Kestutis

    2015-03-15

    Photonic crystals are well known for their celebrated photonic band-gaps—the forbidden frequency ranges, for which the light waves cannot propagate through the structure. The frequency (or chromatic) band-gaps of photonic crystals can be utilized for frequency filtering. In analogy to the chromatic band-gaps and the frequency filtering, the angular band-gaps and the angular (spatial) filtering are also possible in photonic crystals. In this article, we review the recent advances of the spatial filtering using the photonic crystals in different propagation regimes and for different geometries. We review the most evident configuration of filtering in Bragg regime (with the back-reflection—i.e., in the configuration with band-gaps) as well as in Laue regime (with forward deflection—i.e., in the configuration without band-gaps). We explore the spatial filtering in crystals with different symmetries, including axisymmetric crystals; we discuss the role of chirping, i.e., the dependence of the longitudinal period along the structure. We also review the experimental techniques to fabricate the photonic crystals and numerical techniques to explore the spatial filtering. Finally, we discuss several implementations of such filters for intracavity spatial filtering.

  2. Photon Luminescence of the Moon

    NASA Technical Reports Server (NTRS)

    Wilson, T.L.; Lee, K.T.

    2009-01-01

    Luminescence is typically described as light emitted by objects at low temperatures, induced by chemical reactions, electrical energy, atomic interactions, or acoustical and mechanical stress. An example is photoluminescence created when photons (electromagnetic radiation) strike a substance and are absorbed, resulting in the emission of a resonant fluorescent or phosphorescent albedo. In planetary science, there exists X-ray fluorescence induced by sunlight absorbed by a regolith a property used to measure some of the chemical composition of the Moon s surface during the Apollo program. However, there exists an equally important phenomenon in planetary science which will be designated here as photon luminescence. It is not conventional photoluminescence because the incoming radiation that strikes the planetary surface is not photons but rather cosmic rays (CRs). Nevertheless, the result is the same: the generation of a photon albedo. In particular, Galactic CRs (GCRs) and solar energetic particles (SEPs) both induce a photon albedo that radiates from the surface of the Moon. Other particle albedos are generated as well, most of which are hazardous (e.g. neutrons). The photon luminescence or albedo of the lunar surface induced by GCRs and SEPs will be derived here, demonstrating that the Moon literally glows in the dark (when there is no sunlight or Earthshine). This extends earlier work on the same subject [1-4]. A side-by-side comparison of these two albedos and related mitigation measures will also be discussed.

  3. Topological Photonics for Continuous Media

    NASA Astrophysics Data System (ADS)

    Silveirinha, Mario

    Photonic crystals have revolutionized light-based technologies during the last three decades. Notably, it was recently discovered that the light propagation in photonic crystals may depend on some topological characteristics determined by the manner how the light states are mutually entangled. The usual topological classification of photonic crystals explores the fact that these structures are periodic. The periodicity is essential to ensure that the underlying wave vector space is a closed surface with no boundary. In this talk, we prove that it is possible calculate Chern invariants for a wide class of continuous bianisotropic electromagnetic media with no intrinsic periodicity. The nontrivial topology of the relevant continuous materials is linked with the emergence of edge states. Moreover, we will demonstrate that continuous photonic media with the time-reversal symmetry can be topologically characterized by a Z2 integer. This novel classification extends for the first time the theory of electronic topological insulators to a wide range of photonic platforms, and is expected to have an impact in the design of novel photonic systems that enable a topologically protected transport of optical energy. This work is supported in part by Fundacao para a Ciencia e a Tecnologia Grant Number PTDC/EEI-TEL/4543/2014.

  4. Relativistic statistical thermodynamics of dense photon gas

    SciTech Connect

    Tsintsadze, Levan N.; Kishimoto, Yasuaki; Callebaut, Dirk K.; Tsintsadze, Nodar L.

    2007-07-15

    We discuss some aspects of interactions of high-frequency electromagnetic waves with plasmas, assuming that the intensity of radiation is sufficiently large, so that the photon-photon interaction is more likely than the photon-plasma particle interaction. In the stationary limit, solving the kinetic equation of the photon gas, we derive a distribution function. With this distribution function at hand, we investigate the adiabatic photon self-capture and obtain the number density of the trapped photons. We employ the distribution function to calculate the thermodynamic quantities for the photon gas. Having expressions of the entropy and the pressure of the photon gas, we define the heat capacities and exhibit the existence of the ratio of the specific heats {gamma}, which equals 7/6 for nonrelativistic temperatures. In addition, we disclose the magnitude of the mean square fluctuation of the number of photons. Finally, we discuss the uniform expansion of the photon gas.

  5. Relativistic statistical thermodynamics of dense photon gas.

    PubMed

    Tsintsadze, Levan N; Kishimoto, Yasuaki; Callebaut, Dirk K; Tsintsadze, Nodar L

    2007-07-01

    We discuss some aspects of interactions of high-frequency electromagnetic waves with plasmas, assuming that the intensity of radiation is sufficiently large, so that the photon-photon interaction is more likely than the photon-plasma particle interaction. In the stationary limit, solving the kinetic equation of the photon gas, we derive a distribution function. With this distribution function at hand, we investigate the adiabatic photon self-capture and obtain the number density of the trapped photons. We employ the distribution function to calculate the thermodynamic quantities for the photon gas. Having expressions of the entropy and the pressure of the photon gas, we define the heat capacities and exhibit the existence of the ratio of the specific heats Gamma , which equals 7/6 for nonrelativistic temperatures. In addition, we disclose the magnitude of the mean square fluctuation of the number of photons. Finally, we discuss the uniform expansion of the photon gas.

  6. Texaphyrin sensitized near-IR-to-visible photon upconversion.

    PubMed

    Deng, Fan; Sun, Wenfang; Castellano, Felix N

    2014-05-01

    Near-IR (NIR) absorption from a Cd(ii) texaphyrin (TXP) has been successfully coupled with rubrene triplet acceptors/annihilators in vacuum degassed dichloromethane to upconvert NIR (670-800 nm) incident photons into yellow fluorescence through sensitized triplet-triplet annihilation. Stern-Volmer analysis of dynamic energy transfer quenching of TXP by rubrene using transient absorption spectroscopy revealed Stern-Volmer and bimolecular quenching constants of 21,000 M(-1) and 5.7 × 10(8) M(-1) s(-1) respectively, for the triplet-triplet energy transfer process. The upconverted emission intensity with respect to the incident excitation power density at 750 nm was shown to vary between quadratic and linear, illustrating the expected kinetic limits for the light producing photochemistry under continuous wave illumination. Furthermore, with increasing TXP sensitizer concentration, the characteristic quadratic-to-linear crossover point shifted to lower incident photon power density. This is consistent with the notion that stronger photon capture in the sensitizer leads to experimental conditions promoting upconversion under milder excitation conditions. The maximum quantum yield of the TXP-sensitized rubrene upconverted fluorescence was 1.54 ± 0.04% under dilute conditions determined relative to [Os(phen)3](PF6)2 under continuous wave excitation conditions. This saturating quantum efficiency was realized when the incident light power dependence reached the quadratic-to-linear crossover point and was constant over the region where the composition displayed linear response to incident light power density. In pulsed laser experiments at higher sensitizer concentrations, the triplet-triplet annihilation quantum yield was determined to saturate at approximately 13%, corresponding to an upconversion yield of ∼10%, suggesting that the dichloromethane solvent either lowers the T2 state of the rubrene acceptor or is somehow attenuating the annihilation reaction between

  7. Texaphyrin sensitized near-IR-to-visible photon upconversion.

    PubMed

    Deng, Fan; Sun, Wenfang; Castellano, Felix N

    2014-05-01

    Near-IR (NIR) absorption from a Cd(ii) texaphyrin (TXP) has been successfully coupled with rubrene triplet acceptors/annihilators in vacuum degassed dichloromethane to upconvert NIR (670-800 nm) incident photons into yellow fluorescence through sensitized triplet-triplet annihilation. Stern-Volmer analysis of dynamic energy transfer quenching of TXP by rubrene using transient absorption spectroscopy revealed Stern-Volmer and bimolecular quenching constants of 21,000 M(-1) and 5.7 × 10(8) M(-1) s(-1) respectively, for the triplet-triplet energy transfer process. The upconverted emission intensity with respect to the incident excitation power density at 750 nm was shown to vary between quadratic and linear, illustrating the expected kinetic limits for the light producing photochemistry under continuous wave illumination. Furthermore, with increasing TXP sensitizer concentration, the characteristic quadratic-to-linear crossover point shifted to lower incident photon power density. This is consistent with the notion that stronger photon capture in the sensitizer leads to experimental conditions promoting upconversion under milder excitation conditions. The maximum quantum yield of the TXP-sensitized rubrene upconverted fluorescence was 1.54 ± 0.04% under dilute conditions determined relative to [Os(phen)3](PF6)2 under continuous wave excitation conditions. This saturating quantum efficiency was realized when the incident light power dependence reached the quadratic-to-linear crossover point and was constant over the region where the composition displayed linear response to incident light power density. In pulsed laser experiments at higher sensitizer concentrations, the triplet-triplet annihilation quantum yield was determined to saturate at approximately 13%, corresponding to an upconversion yield of ∼10%, suggesting that the dichloromethane solvent either lowers the T2 state of the rubrene acceptor or is somehow attenuating the annihilation reaction between

  8. What is a photon?

    NASA Astrophysics Data System (ADS)

    Kracklauer, A. F.

    2015-09-01

    The linguistic and epistemological constraints on finding and expressing an answer to the title question are reviewed. First, it is recalled that "fields" are defined in terms of their effect on "test charges" and not in terms of any, even idealistically considered, primary, native innate qualities of their own. Thus, before fields can be discussed, the theorist has to have already available a defined "test particle" and field source. Clearly, neither the test nor the engendering particles can be defined as elements of the considered field without redefining the term "field." Further, the development of a theory as a logical structure (i.e., an internally self consistent conceptual complex) entails that the subject(s) of the theory (the primitive elements) and the rules governing their interrelationships (axioms) cannot be deduced by any logical procedure. They are always hypothesized on the basis of intuition supported by empirical experience. Given hypothesized primitive elements and axioms it is possible, in principle, to test for the 'completion' of the axiom set (i.e., any addition introduces redundancy) and for self consistency. Thus, theory building is limited to establishing the self consistency of a theory's mathematical expression and comparing that with the external, ontic world. Finally, a classical model with an event-by-event simulation of an EPR-B experiment to test a Bell Inequality is described. This model leads to a violation of Bell's limit without any quantum input (no nonlocal interaction nor entanglement), thus substantiating previous critical analysis of the derivation of Bell inequalities. On the basis of this result, it can be concluded that the electromagnetic interaction possesses no preternatural aspects, and that the usual models in terms of waves, fields and photons are all just imaginary constructs with questionable relation to a presumed reality.

  9. A Photon Collider Experiment based on SLC

    SciTech Connect

    Gronberg, J

    2003-11-01

    Technology for a photon collider experiment at a future TeV-scale linear collider has been under development for many years. The laser and optics technology has reached the point where a GeV-scale photon collider experiment is now feasible. We report on the photon-photon luminosities that would be achievable at a photon collider experiment based on a refurbished Stanford Linear Collider.

  10. Nonlinear collective effects in photon-photon and photon-plasma interactions

    NASA Astrophysics Data System (ADS)

    Marklund, Mattias; Shukla, Padma K.

    2006-04-01

    Strong-field effects in laboratory and astrophysical plasmas and high intensity laser and cavity systems are considered, related to quantum electrodynamical (QED) photon-photon scattering. Current state-of-the-art laser facilities are close to reaching energy scales at which laboratory astrophysics will become possible. In such high energy density laboratory astrophysical systems, quantum electrodynamics will play a crucial role in the dynamics of plasmas and indeed the vacuum itself. Developments such as the free-electron laser may also give a means for exploring remote violent events such as supernovae in a laboratory environment. At the same time, superconducting cavities have steadily increased their quality factors, and quantum nondemolition measurements are capable of retrieving information from systems consisting of a few photons. Thus, not only will QED effects such as elastic photon-photon scattering be important in laboratory experiments, it may also be directly measurable in cavity experiments. Here implications of collective interactions between photons and photon-plasma systems are described. An overview of strong field vacuum effects is given, as formulated through the Heisenberg-Euler Lagrangian. Based on the dispersion relation for a single test photon traveling in a slowly varying background electromagnetic field, a set of equations describing the nonlinear propagation of an electromagnetic pulse on a radiation plasma is derived. The stability of the governing equations is discussed, and it is shown using numerical methods that electromagnetic pulses may collapse and split into pulse trains, as well as be trapped in a relativistic electron hole. Effects, such as the generation of novel electromagnetic modes, introduced by QED in pair plasmas is described. Applications to laser-plasma systems and astrophysical environments are also discussed.

  11. Production and dosimetry of simultaneous therapeutic photons and electrons beam by linear accelerator: A Monte Carlo study

    SciTech Connect

    Khledi, Navid; Sardari, Dariush; Arbabi, Azim; Ameri, Ahmad; Mohammadi, Mohammad

    2015-02-24

    Depending on the location and depth of tumor, the electron or photon beams might be used for treatment. Electron beam have some advantages over photon beam for treatment of shallow tumors to spare the normal tissues beyond of the tumor. In the other hand, the photon beam are used for deep targets treatment. Both of these beams have some limitations, for example the dependency of penumbra with depth, and the lack of lateral equilibrium for small electron beam fields. In first, we simulated the conventional head configuration of Varian 2300 for 16 MeV electron, and the results approved by benchmarking the Percent Depth Dose (PDD) and profile of the simulation and measurement. In the next step, a perforated Lead (Pb) sheet with 1mm thickness placed at the top of the applicator holder tray. This layer producing bremsstrahlung x-ray and a part of the electrons passing through the holes, in result, we have a simultaneous mixed electron and photon beam. For making the irradiation field uniform, a layer of steel placed after the Pb layer. The simulation was performed for 10×10, and 4×4 cm2 field size. This study was showed the advantages of mixing the electron and photon beam by reduction of pure electron's penumbra dependency with the depth, especially for small fields, also decreasing of dramatic changes of PDD curve with irradiation field size.

  12. Silicon photonics: some remaining challenges

    NASA Astrophysics Data System (ADS)

    Reed, G. T.; Topley, R.; Khokhar, A. Z.; Thompson, D. J.; Stanković, S.; Reynolds, S.; Chen, X.; Soper, N.; Mitchell, C. J.; Hu, Y.; Shen, L.; Martinez-Jimenez, G.; Healy, N.; Mailis, S.; Peacock, A. C.; Nedeljkovic, M.; Gardes, F. Y.; Soler Penades, J.; Alonso-Ramos, C.; Ortega-Monux, A.; Wanguemert-Perez, G.; Molina-Fernandez, I.; Cheben, P.; Mashanovich, G. Z.

    2016-03-01

    This paper discusses some of the remaining challenges for silicon photonics, and how we at Southampton University have approached some of them. Despite phenomenal advances in the field of Silicon Photonics, there are a number of areas that still require development. For short to medium reach applications, there is a need to improve the power consumption of photonic circuits such that inter-chip, and perhaps intra-chip applications are viable. This means that yet smaller devices are required as well as thermally stable devices, and multiple wavelength channels. In turn this demands smaller, more efficient modulators, athermal circuits, and improved wavelength division multiplexers. The debate continues as to whether on-chip lasers are necessary for all applications, but an efficient low cost laser would benefit many applications. Multi-layer photonics offers the possibility of increasing the complexity and effectiveness of a given area of chip real estate, but it is a demanding challenge. Low cost packaging (in particular, passive alignment of fibre to waveguide), and effective wafer scale testing strategies, are also essential for mass market applications. Whilst solutions to these challenges would enhance most applications, a derivative technology is emerging, that of Mid Infra-Red (MIR) silicon photonics. This field will build on existing developments, but will require key enhancements to facilitate functionality at longer wavelengths. In common with mainstream silicon photonics, significant developments have been made, but there is still much left to do. Here we summarise some of our recent work towards wafer scale testing, passive alignment, multiplexing, and MIR silicon photonics technology.

  13. Investigation of a photon counting avalanche photodiode from Hamamatsu photonics

    NASA Astrophysics Data System (ADS)

    Britvitch, I.; Musienko, Y.; Renker, D.

    2006-11-01

    Multi-cell avalanche photodiodes (APDs) operating in Geiger mode have been shown to be a very promising alternative to photomultiplier tubes for the detection of single photons at room temperature. Like a photomultiplier they have high gain and a fast rise time and they are insensitive to pickup. Beyond it they operate in high magnetic fields, are compact and need a relatively low bias voltage. It is expected that the MOS production technique makes them cheap. Recently PSI and Hamamatsu Photonics worked together for the development of a radiation-hard APD for CMS ECAL and had very good success. The development continued based on a similar design for a photon counting multielement Geiger-mode APD with an area of 1×1 mm 2. The properties of this device have been measured and will be reported.

  14. Photonics Research and Development

    SciTech Connect

    Dickson, Elizabeth

    2010-01-15

    During the period August 2005 through October 2009, the UNLV Research Foundation (UNLVRF), a non-profit affiliate of the University of Nevada, Las Vegas (UNLV), in collaboration with UNLV's Colleges of Science and Engineering; Boston University (BU); Oak Ridge National Laboratory (ORNL); and Sunlight Direct, LLC, has managed and conducted a diverse and comprehensive research and development program focused on light-emitting diode (LED) technologies that provide significantly improved characteristics for lighting and display applications. This final technical report provides detailed information on the nature of the tasks, the results of the research, and the deliverables. It is estimated that about five percent of the energy used in the nation is for lighting homes, buildings and streets, accounting for some 25 percent of the average home's electric bill. However, the figure is significantly higher for the commercial sector. About 60 percent of the electricity for businesses is for lighting. Thus replacement of current lighting with solid-state lighting technology has the potential to significantly reduce this nation's energy consumption by some estimates, possibly as high as 20%. The primary objective of this multi-year R&D project has been to develop and advance lighting technologies to improve national energy conversion efficiencies; reduce heat load; and significantly lower the cost of conventional lighting technologies. The UNLVRF and its partners have specifically focused these talents on (1) improving LED technologies; (2) optimizing hybrid solar lighting, a technology which potentially offers the benefits of blending natural with artificial lighting systems, thus improving energy efficiency; and (3) building a comprehensive academic infrastructure within UNLV which concentrates on photonics R&D. Task researchers have reported impressive progress in (1) the development of quantum dot laser emitting diodes (QDLEDs) which will ultimately improve energy

  15. Theoretical exploration of the nanoscale host-guest interactions between [n]cycloparaphenylenes (n = 10, 8 and 9) and fullerene C₆₀: from single- to three-potential well.

    PubMed

    Yuan, Kun; Zhou, Cai-Hua; Zhu, Yuan-Cheng; Zhao, Xiang

    2015-07-28

    The nanoscale host-guest interactions between [n]cycloparaphenylene ([n]CPP; n = 10, 8 and 9) nano-ring and fullerene C60 were explored theoretically. It is found that relatively small variations in the sizes of the [n]CPP host lead to very significant changes in encapsulation property toward the fullerene C60 guest. Expectedly, one stable inclusion-configuration of [10]CPP⊃C60 and one floating-configuration of [8]CPP⊃C60 are located on the potential surfaces of the two complexes, respectively. Unexpectedly, besides a floating-configuration (F-[9]CPP⊃C60), another stable inclusion-configuration (I-[9]CPP⊃C60) is also located on the potential surface of [9]CPP⊃C60 host-guest complex. Interaction energies and natural steric analysis show that these complexes are stabilized by balancing concave-convex π-π attractive and steric repulsive host-guest interactions. In contrast, the steric repulsive energy (Es) between host and guest of I-[9]CPP⊃C60 is as high as 233.12 kJ mol(-1), which is much larger than those in other complexes. The movements of C60 guest through the cavities of [n]CPP host (n = 10, 8 and 9) are simulated by calculating the energy profile, and the results interestingly reveal that the encapsulation of C60 by [10]CPP is in the manner of a single-potential well, by [8]CPP in the manner of a double-potential well, and by [9]CPP in the special manner of a three-potential well. We predict that the movement of C60 guest through the cavity of [9]CPP host should be experimentally observable owing to the relatively low energy barrier (<50 kJ mol(-1), M06-2X/6-31G(d)). Charge population analysis shows that an obvious charge transfer between host and guest takes place during the formation of I-[9]CPP⊃C60, which is different from those during the formation of [8]CPP⊃C60, [10]CPP⊃C60 and F-[9]CPP⊃C60. Additionally, the host-guest interaction regions were detected and visualized in real space based on the electron density and reduced density

  16. Funneling single photons into ridge-waveguide photonic integrated circuits

    NASA Astrophysics Data System (ADS)

    Fattah poor, S.; Midolo, L.; Li, L. H.; Linfield, E. H.; Schouwenberg, J. F. P.; Xia, T.; van Otten, F. W. M.; Hoang, T. B.; Fiore, A.

    2013-02-01

    The generation, manipulation and detection of single photons enable quantum communication, simulation and potentially computing protocols. However scaling to several qubits requires the integration of these functionalities in a single chip. A promising approach to the integration of single-photon sources in a chip is the use of single quantum dots embedded in photonic crystal waveguides or cavities. To this aim, efficient coupling of the emission from single quantum dots in photonic crystal cavities to low-loss ridge-waveguide (RWG) circuits is needed. This is usually hampered by the large mode mismatch between the two systems. In this work the emission of a photonic crystal (PhC) cavity realized on a GaAs/AlGaAs membrane and pumped by quantum dots has been effectively coupled and transferred through a long RWG (~1mm). By continuous tapering in both horizontal and vertical direction, transmission values (fiber-in, fiber-out) around 0.16 and 0.08% for RWG and coupled PhC waveguide-RWG have been achieved, respectively. This corresponds to about 2.8% coupling efficiency between the center of the PhC waveguide and the single-mode output fiber, a value much higher than what is achieved by top collection. It further shows that around 70% of the light in the PhC waveguide is coupled to the RWG. The emission from quantum dots in the cavity has been clearly identified by exciting from the top and collecting the photoluminescence from the cleaved facet of the device 1mm away from the cavity which enables the efficient coupling of single photons to RWG and detector circuits.

  17. Liquid crystal applications in photonics

    NASA Astrophysics Data System (ADS)

    Chigrinov, Vladimir G.

    2009-02-01

    Liquid crystal (LC) devices for Photonics applications is a hot topic of research. Such elements begin to appear in Photonics market. Passive elements for fiber optical communication systems (DWDM components) based on LC cells can successfully compete with the other elements used for the purpose, such as micro electromechanical (MEM), thermo-optical, opto-mechanical or acousto-optical devices. We have already successfully fabricated certain prototypes of the optical switches based on various electrooptic modes in ferroelectric and nematic LC materials. The electrooptical modes used for the purpose included the light polarization rotation, voltage controllable diffraction and fast switching of the LC refractive index. Use of photo-alignment technique pioneered by us makes it possible to develop new LC fiber components. Almost all the criteria of perfect LC alignment are met in case of azo-dye layers. We have already used azo-dye materials to align LC in superthin photonic holes, curved and 3D surfaces and as cladding layers in microring silicon based resonators. We have already used the photoaligning materials to align LC mixtures in small cavities, such as the holes and tubes of photonic crystals, having size of 1 μm and less and obtained excellent LC orientation inside the tubes by photoalignment. The prototypes of new LC efficient Photonics devices, such as optically rewritable LC waveguides and voltage controllable diffraction gratings are envisaged. The polarization controllers, polarization rotators, variable optical attenuators and other passive LC optical elements for fiber communication networks are under way.

  18. High precision photon flux determination for photon tagging experiments

    SciTech Connect

    Teymurazyan, A; Ahmidouch, A; Ambrozewicz, P; Asratyan, A; Baker, K; Benton, L; Burkert, V; Clinton, E; Cole, P; Collins, P; Dale, D; Danagoulian, S; Davidenko, G; Demirchyan, R; Deur, A; Dolgolenko, A; Dzyubenko, G; Ent, R; Evdokimov, A; Feng, J; Gabrielyan, M; Gan, L; Gasparian, A; Glamazdin, A; Goryachev, V; Hardy, K; He, J; Ito, M; Jiang, L; Kashy, D; Khandaker, M; Kolarkar, A; Konchatnyi, M; Korchin, A; Korsch, W; Kosinov, O; Kowalski, S; Kubantsev, M; Kubarovsky, V; Larin, I; Lawrence, D; Li, X; Martel, P; Matveev, V; McNulty, D; Mecking, B; Milbrath, B; Minehart, R; Miskimen, R; Mochalov, V; Nakagawa, I; Overby, S; Pasyuk, E; Payen, M; Pedroni, R; Prok, Y; Ritchie, B; Salgado, C; Shahinyan, A; Sitnikov, A; Sober, D; Stepanyan, S; Stevens, W; Underwood, J; Vasiliev, A; Vishnyakov, V; Wood, M; Zhou, S

    2014-07-01

    The Jefferson Laboratory PrimEx Collaboration has developed and implemented a method to control the tagged photon flux in photoproduction experiments at the 1% level over the photon energy range from 4.9 to 5.5 GeV. This method has been successfully implemented in a high precision measurement of the neutral pion lifetime. Here, we outline the experimental equipment and the analysis techniques used to accomplish this. These include the use of a total absorption counter for absolute flux calibration, a pair spectrometer for online relative flux monitoring, and a new method for post-bremsstrahlung electron counting.

  19. Nonlinear phase shift from photon-photon scattering in vacuum.

    PubMed

    Ferrando, Albert; Michinel, Humberto; Seco, Marcos; Tommasini, Daniele

    2007-10-12

    We show that QED nonlinear effects imply a phase correction to the linear evolution of electromagnetic waves in vacuum. We provide explicit solutions of the modified Maxwell equations for the propagation of a superposition of two plane waves and calculate analytically and numerically the corresponding phase shift. This provides a new framework for the search of all-optical signatures of photon-photon scattering in vacuum. In particular, we propose an experiment for measuring the phase shift in projected high-power laser facilities.

  20. Determination of small field output factors in 6 and 10 MV flattening filter free photon beams using various detectors

    NASA Astrophysics Data System (ADS)

    Masanga, W.; Tangboonduangjit, P.; Khamfongkhruea, C.; Tannanonta, C.

    2016-03-01

    The study aimed to determine appropriate detectors for output factor measurement of small fields in 6 and 10 MV flattening filter free photon beams using five different detectors. Field sizes were varied between 0.6 × 0.6 and 4.0 × 4.0 cm2. An indirect method (daisy-chaining) was applied to normalize the output factors. For the smallest field size, the variations of output factors compared among the detectors were 13%. Exradin A16 had the lowest output factor and increasing in sequence with CC01, microDiamond, microLion and EDGE detectors, respectively, for both energies. The similarity between CC01 and microDiamond output factor values were within 1.6% and 1% for all field sizes of 6 and 10 MV FFF, respectively. EDGE and microLion presented the highest values while ExradinA16 gave lowest values. In conclusion, IBACC01, Exradin A16, microLion, microDiamond and EDGE detectors seem to be the detectors of choices for small field output factor measurement of FFF beams down to 1.6 × 1.6 cm2. However, we could not guarantee which detector is the most suitable for output factor measurement in small field less than 1.6 × 1.6 cm2 of FFF beams. Further studies are required to provide reference information for validation purposes.

  1. Two photon thermal sensing in Er3+/Yb3+ co-doped nanocrystalline NaNbO3.

    PubMed

    Kumar, Kagola Upendra; Santos, Weslley Queiroz; Silva, Wagner Ferreira; Jacinto, Carlos

    2013-10-01

    We investigate the potential use of two-photon absorption of Er3+/Yb3+ co-doped NaNbO3 nanocrystals for nanothermometry as well as thermal imaging, based on the thermally coupled green Er3+ emission lines. In fact, thermal sensor in the range of 20-80 degrees C with -0.1 degrees C accuracy using excitation powers readily obtained from commercially available semiconductor laser was achieved. The pump-intensity induced local heating was also investigated upon femtosecond laser excitation and 0.55 K/kW x cm(-2) was achieved. The highly efficient green emission together with two-photon dependence and femtosecond laser excitation should increase the brightness of thermal imaging. Additionally, the high temperature-sensitive fluorescence, when compared to previous literatures, should increase the resolution of nanothermometers. PMID:24245152

  2. Two photon thermal sensing in Er3+/Yb3+ co-doped nanocrystalline NaNbO3.

    PubMed

    Kumar, Kagola Upendra; Santos, Weslley Queiroz; Silva, Wagner Ferreira; Jacinto, Carlos

    2013-10-01

    We investigate the potential use of two-photon absorption of Er3+/Yb3+ co-doped NaNbO3 nanocrystals for nanothermometry as well as thermal imaging, based on the thermally coupled green Er3+ emission lines. In fact, thermal sensor in the range of 20-80 degrees C with -0.1 degrees C accuracy using excitation powers readily obtained from commercially available semiconductor laser was achieved. The pump-intensity induced local heating was also investigated upon femtosecond laser excitation and 0.55 K/kW x cm(-2) was achieved. The highly efficient green emission together with two-photon dependence and femtosecond laser excitation should increase the brightness of thermal imaging. Additionally, the high temperature-sensitive fluorescence, when compared to previous literatures, should increase the resolution of nanothermometers.

  3. Relative biological damage in and out of field of 6, 10 and 18 MV clinical photon beams

    NASA Astrophysics Data System (ADS)

    Ezzati, A. O.

    2016-08-01

    The lower energy of scattered radiation in and out of a megavoltage (MV) photon beam suggests that relative biological damage (RBD) may change from in- to out-of-field regions for unit absorbed dose. Because of high linear energy transfer (LET) and potential of causing severe damage to the DNA, low-energy (10 eV-1 keV) slowing down electrons should be included in radiation biological damage calculations. In this study RBD was calculated in and out of field of 6, 10 and 18 MV clinical photon beams including low-energy slowing down electrons in the track length estimated method. Electron spectra at energies higher than 2 keV were collected in a water phantom at different depths and off-axis points by using the MCNP code. A new extrapolation method was used to estimate the electron spectra at energies lower than 2 keV. The obtained spectra at energies lower than 2 keV merged with spectra at energies higher than 2 keV by using continuity of the spectra. These spectra were used as an input to a validated microdosimetric Monte Carlo (MC) code, MC damage simulation (MCDS), to calculate the RBD of induced DSB in DNA at points in and out of the primary radiation field under fully aerobic (100% O2 and anoxic (0% O2 conditions. There was an observable difference in the energy spectra for electrons for points in the primary radiation field and those points out of field. RBD had maximum variation, 11% in 6 MV photons at field size of 20×20 cm2. This variation was less than 11% for 10 and 18 MV photons and field sizes smaller than 20×20 cm2. Our simulations also showed that under the anoxic condition, RBD increases up to 6% for 6 and 10 MV photons and the 20×20 cm2 field size. This work supports the hypothesis that in megavoltage treatments out-of-field radiation quality can vary enough to have an impact on RBD per unit dose and that this may play a role as the radiation therapy community explores biological optimization as a tool to assist treatment planning.

  4. Single-photon decision maker

    PubMed Central

    Naruse, Makoto; Berthel, Martin; Drezet, Aurélien; Huant, Serge; Aono, Masashi; Hori, Hirokazu; Kim, Song-Ju

    2015-01-01

    Decision making is critical in our daily lives and for society in general and is finding evermore practical applications in information and communication technologies. Herein, we demonstrate experimentally that single photons can be used to make decisions in uncertain, dynamically changing environments. Using a nitrogen-vacancy in a nanodiamond as a single-photon source, we demonstrate the decision-making capability by solving the multi-armed bandit problem. This capability is directly and immediately associated with single-photon detection in the proposed architecture, leading to adequate and adaptive autonomous decision making. This study makes it possible to create systems that benefit from the quantum nature of light to perform practical and vital intelligent functions. PMID:26278007

  5. Quantum photonics hybrid integration platform

    SciTech Connect

    Murray, E.; Floether, F. F.; Ellis, D. J. P.; Meany, T.; Bennett, A. J. Shields, A. J.; Lee, J. P.; Griffiths, J. P.; Jones, G. A. C.; Farrer, I.; Ritchie, D. A.

    2015-10-26

    Fundamental to integrated photonic quantum computing is an on-chip method for routing and modulating quantum light emission. We demonstrate a hybrid integration platform consisting of arbitrarily designed waveguide circuits and single-photon sources. InAs quantum dots (QD) embedded in GaAs are bonded to a SiON waveguide chip such that the QD emission is coupled to the waveguide mode. The waveguides are SiON core embedded in a SiO{sub 2} cladding. A tuneable Mach Zehnder interferometer (MZI) modulates the emission between two output ports and can act as a path-encoded qubit preparation device. The single-photon nature of the emission was verified using the on-chip MZI as a beamsplitter in a Hanbury Brown and Twiss measurement.

  6. Radiating dipoles in photonic crystals

    PubMed

    Busch; Vats; John; Sanders

    2000-09-01

    The radiation dynamics of a dipole antenna embedded in a photonic crystal are modeled by an initially excited harmonic oscillator coupled to a non-Markovian bath of harmonic oscillators representing the colored electromagnetic vacuum within the crystal. Realistic coupling constants based on the natural modes of the photonic crystal, i.e., Bloch waves and their associated dispersion relation, are derived. For simple model systems, well-known results such as decay times and emission spectra are reproduced. This approach enables direct incorporation of realistic band structure computations into studies of radiative emission from atoms and molecules within photonic crystals. We therefore provide a predictive and interpretative tool for experiments in both the microwave and optical regimes.

  7. Single-photon decision maker

    NASA Astrophysics Data System (ADS)

    Naruse, Makoto; Berthel, Martin; Drezet, Aurélien; Huant, Serge; Aono, Masashi; Hori, Hirokazu; Kim, Song-Ju

    2015-08-01

    Decision making is critical in our daily lives and for society in general and is finding evermore practical applications in information and communication technologies. Herein, we demonstrate experimentally that single photons can be used to make decisions in uncertain, dynamically changing environments. Using a nitrogen-vacancy in a nanodiamond as a single-photon source, we demonstrate the decision-making capability by solving the multi-armed bandit problem. This capability is directly and immediately associated with single-photon detection in the proposed architecture, leading to adequate and adaptive autonomous decision making. This study makes it possible to create systems that benefit from the quantum nature of light to perform practical and vital intelligent functions.

  8. Photonic quantum technologies (Presentation Recording)

    NASA Astrophysics Data System (ADS)

    O'Brien, Jeremy L.

    2015-09-01

    The impact of quantum technology will be profound and far-reaching: secure communication networks for consumers, corporations and government; precision sensors for biomedical technology and environmental monitoring; quantum simulators for the design of new materials, pharmaceuticals and clean energy devices; and ultra-powerful quantum computers for addressing otherwise impossibly large datasets for machine learning and artificial intelligence applications. However, engineering quantum systems and controlling them is an immense technological challenge: they are inherently fragile; and information extracted from a quantum system necessarily disturbs the system itself. Of the various approaches to quantum technologies, photons are particularly appealing for their low-noise properties and ease of manipulation at the single qubit level. We have developed an integrated waveguide approach to photonic quantum circuits for high performance, miniaturization and scalability. We will described our latest progress in generating, manipulating and interacting single photons in waveguide circuits on silicon chips.

  9. Detecting itinerant single microwave photons

    NASA Astrophysics Data System (ADS)

    Sathyamoorthy, Sankar Raman; Stace, Thomas M.; Johansson, Göran

    2016-08-01

    Single-photon detectors are fundamental tools of investigation in quantum optics and play a central role in measurement theory and quantum informatics. Photodetectors based on different technologies exist at optical frequencies and much effort is currently being spent on pushing their efficiencies to meet the demands coming from the quantum computing and quantum communication proposals. In the microwave regime, however, a single-photon detector has remained elusive, although several theoretical proposals have been put forth. In this article, we review these recent proposals, especially focusing on non-destructive detectors of propagating microwave photons. These detection schemes using superconducting artificial atoms can reach detection efficiencies of 90% with the existing technologies and are ripe for experimental investigations.

  10. Speckle statistics of entangled photons

    NASA Astrophysics Data System (ADS)

    Klein, Avraham; Agam, Oded; Spivak, Boris

    2016-07-01

    We consider the propagation of several entangled photons through an elastically scattering medium and study statistical properties of their speckle patterns. We find the spatial correlations of multiphoton speckles and their sensitivity to changes of system parameters. Our analysis covers both the directed-wave regime, where rays propagate almost ballistically while experiencing small-angle diffusion, and the real-space diffusive regime. We demonstrate that long-range correlations of the speckle patterns dominate experimental signatures for large-aperture photon detectors. We also show that speckle sensitivity depends strongly on the number of photons N in the incoming beam, increasing as √{N } in the directed-wave regime and as N in the diffusive regime.

  11. Apparatus for photon activation positron annihilation analysis

    DOEpatents

    Akers, Douglas W.

    2007-06-12

    Non-destructive testing apparatus according to one embodiment of the invention comprises a photon source. The photon source produces photons having predetermined energies and directs the photons toward a specimen being tested. The photons from the photon source result in the creation of positrons within the specimen being tested. A detector positioned adjacent the specimen being tested detects gamma rays produced by annihilation of positrons with electrons. A data processing system operatively associated with the detector produces output data indicative of a lattice characteristic of the specimen being tested.

  12. Photonic quantum information: science and technology

    PubMed Central

    TAKEUCHI, Shigeki

    2016-01-01

    Recent technological progress in the generation, manipulation and detection of individual single photons has opened a new scientific field of photonic quantum information. This progress includes the realization of single photon switches, photonic quantum circuits with specific functions, and the application of novel photonic states to novel optical metrology beyond the limits of standard optics. In this review article, the recent developments and current status of photonic quantum information technology are overviewed based on the author’s past and recent works. PMID:26755398

  13. Variability in fluence and spectrum of high-energy photon bursts produced by lightning leaders

    NASA Astrophysics Data System (ADS)

    Celestin, Sebastien; Xu, Wei; Pasko, Victor P.

    2015-12-01

    In this paper, we model the production and acceleration of thermal runaway electrons during negative corona flash stages of stepping lightning leaders and the corresponding terrestrial gamma ray flashes (TGFs) or negative cloud-to-ground (-CG) lightning-produced X-ray bursts in a unified fashion. We show how the source photon spectrum and fluence depend on the potential drop formed in the lightning leader tip region during corona flash and how the X-ray burst spectrum progressively converges toward typical TGF spectrum as the potential drop increases. Additionally, we show that the number of streamers produced in a negative corona flash, the source electron energy distribution function, the corresponding number of photons, and the photon energy distribution and transport through the atmosphere up to low-orbit satellite altitudes exhibit a very strong dependence on this potential drop. This leads to a threshold effect causing X-rays produced by leaders with potentials lower than those producing typical TGFs extremely unlikely to be detected by low-orbit satellites. Moreover, from the number of photons in X-ray bursts produced by -CGs estimated from ground observations, we show that the proportionality between the number of thermal runaway electrons and the square of the potential drop in the leader tip region during negative corona flash proposed earlier leads to typical photon fluences on the order of 1 ph/cm2 at an altitude of 500 km and a radial distance of 200 km for intracloud lightning discharges producing 300 MV potential drops, which is consistent with observations of TGF fluences and spectra from satellites.

  14. Spontaneous ultraweak photon emission from biological systems and the endogenous light field.

    PubMed

    Schwabl, Herbert; Klima, Herbert

    2005-04-01

    Still one of the most astonishing biological electromagnetic phenomena is the ultraweak photon emission (UPE) from living systems. Organisms and tissues spontaneously emit measurable intensities of light, i.e. photons in the visible part of the electromagnetic spectrum (380-780 nm), in the range from 1 to 1,000 photons x s-1 x cm-2, depending on their condition and vitality. It is important not to confuse UPE from living systems with other biogenic light emitting processes such as bioluminescence or chemiluminescence. This article examines with basic considerations from physics on the quantum nature of photons the empirical phenomenon of UPE. This leads to the description of the non-thermal origin of this radiation. This is in good correspondence with the modern understanding of life phenomena as dissipative processes far from thermodynamic equilibrium. UPE also supports the understanding of life sustaining processes as basically driven by electromagnetic fields. The basic features of UPE, like intensity and spectral distribution, are known in principle for many experimental situations. The UPE of human leukocytes contributes to an endogenous light field of about 1011 photons x s-1 which can be influenced by certain factors. Further research is needed to reveal the statistical properties of UPE and in consequence to answer questions about the underlying mechanics of the biological system. In principle, statistical properties of UPE allow to reconstruct phase-space dynamics of the light emitting structures. Many open questions remain until a proper understanding of the electromagnetic interaction of the human organism can be achieved: which structures act as receptors and emitters for electromagnetic radiation? How is electromagnetic information received and processed within cells?

  15. Systematics of photon strength functions

    NASA Astrophysics Data System (ADS)

    Firestone, Richard

    2015-10-01

    The photon strength of high energy E1 transitions is well described by Brink-Axel theory based on the contribution of the Giant Dipole Resonance. No adequate theory is available for M1 and E2 transitions which do not generally compete strongly with high energy E1 transitions. Measurements with the 57Fe(3He,3He') reaction at the Oslo cyclotron have revealed that the photon strength below 2 MeV greatly exceeds BA predictions. Similar results have been found for numerous other nuclides. In this paper I will discuss my analysis of the 56Fe(n,γ)57Fe reaction which we investigated with both cold neutrons from the Budapest Reactor and thermal neutrons from the Rez Reactor (Prague). A >99% complete 57Fe capture γ-ray decay scheme containing 449 γ-rays deexciting 100 levels has been constructed on the basis of γ-ray singles and γγ -coincidence data. The photon strengths for 90 primary γ-rays with energies ranging from 92-7646 keV were calculated and compared with the predictions of Brink-Axel (BA) theory. Excellent agreement has been attained for the high energy transitions while the strength below 2 MeV exceeds BA predictions confirming the earlier Oslo (3He,3He' γ) results. Photon strengths for another 95 secondary M1, E1, and E2 γ-rays were also determined to also exceed BA predictions for transitions below 4 MeV. The dependence of photon strength on level energy and the statistical distribution of photon strengths will also be discussed in this talk.

  16. Quantum cryptography with entangled photons

    PubMed

    Jennewein; Simon; Weihs; Weinfurter; Zeilinger

    2000-05-15

    By realizing a quantum cryptography system based on polarization entangled photon pairs we establish highly secure keys, because a single photon source is approximated and the inherent randomness of quantum measurements is exploited. We implement a novel key distribution scheme using Wigner's inequality to test the security of the quantum channel, and, alternatively, realize a variant of the BB84 protocol. Our system has two completely independent users separated by 360 m, and generates raw keys at rates of 400-800 bits/s with bit error rates around 3%.

  17. Quantum cryptography with entangled photons

    PubMed

    Jennewein; Simon; Weihs; Weinfurter; Zeilinger

    2000-05-15

    By realizing a quantum cryptography system based on polarization entangled photon pairs we establish highly secure keys, because a single photon source is approximated and the inherent randomness of quantum measurements is exploited. We implement a novel key distribution scheme using Wigner's inequality to test the security of the quantum channel, and, alternatively, realize a variant of the BB84 protocol. Our system has two completely independent users separated by 360 m, and generates raw keys at rates of 400-800 bits/s with bit error rates around 3%. PMID:10990782

  18. Detection of Recurrent Fluorescence Photons

    NASA Astrophysics Data System (ADS)

    Ebara, Yuta; Furukawa, Takeshi; Matsumoto, Jun; Tanuma, Hajime; Azuma, Toshiyuki; Shiromaru, Haruo; Hansen, Klavs

    2016-09-01

    We have detected visible photons emitted from the thermally populated electronic excited state, namely recurrent fluorescence (RF), of C6- stored in an electrostatic ion storage ring. Clear evidence is provided to distinguish RF from normal fluorescence, based on the temporal profile of detected photons synchronized with the revolution of C6- in the ring, for which the time scale is far longer than the lifetime of the intact photoexcited state. The relaxation (cooling) process via RF is likely to be commonplace for isolated molecular systems and crucial to the stabilization of molecules in interstellar environments.

  19. Frequency-bin entangled photons

    SciTech Connect

    Olislager, L.; Emplit, P.; Nguyen, A. T.; Massar, S.; Merolla, J.-M.; Huy, K. Phan

    2010-07-15

    A monochromatic laser pumping a parametric down-conversion crystal generates frequency-entangled photon pairs. We study this experimentally by addressing such frequency-entangled photons at telecommunication wavelengths (around 1550 nm) with fiber-optics components such as electro-optic phase modulators and narrow-band frequency filters. The theory underlying our approach uses the notion of frequency-bin entanglement. Our results show that the phase modulators address coherently up to eleven frequency bins, leading to an interference pattern which can violate by more than five standard deviations a Bell inequality adapted to our setup.

  20. The effect of energy spectrum change on DNA damage in and out of field in 10-MV clinical photon beams.

    PubMed

    Ezzati, A O; Xiao, Y; Sohrabpour, M; Studenski, M T

    2015-01-01

    The aim of this study was to quantify the DNA damage induced in a clinical megavoltage photon beam at various depths in and out of the field. MCNPX was used to simulate 10 × 10 and 20 × 20 cm(2) 10-MV photon beams from a clinical linear accelerator. Photon and electron spectra were collected in a water phantom at depths of 2.5, 12.5 and 22.5 cm on the central axis and at off-axis points out to 10 cm. These spectra were used as an input to a validated microdosimetric Monte Carlo code, MCDS, to calculate the RBE of induced DSB in DNA at points in and out of the primary radiation field at three depths. There was an observable difference in the energy spectra for photons and electrons for points in the primary radiation field and those points out of field. In the out-of-field region, the mean energy for the photon and electron spectra decreased by a factor of about six and three from the in-field mean energy, respectively. Despite the differences in spectra and mean energy, the change in RBE was <1 % from the in-field region to the out-of-field region at any depth. There was no significant change in RBE regardless of the location in the phantom. Although there are differences in both the photon and electron spectra, these changes do not correlate with a change in RBE in a clinical MV photon beam as the electron spectra are dominated by electrons with energies >20 keV.

  1. Dow Corning photonics: the silicon advantage in automotive photonics

    NASA Astrophysics Data System (ADS)

    Clapp, Terry V.; Paquet, Rene; Norris, Ann; Pettersen, Babette

    2005-02-01

    The Automotive Market offers several opportunities for Dow Corning to leverage the power of silicon-based materials. Dow Corning Photonics Solutions has a number of developments that may be attractive for the emergent photonics needs in automobiles, building on 40 years of experience as a leading Automotive supplier with a strong foundation of expertise and an extensive product offering- from encapsulents and highly reliable resins, adhesives, insulating materials and other products, ensuring that the advantage of silicones are already well-embedded in Automotive systems, modules and components. The recent development of LED encapsulants of exceptional clarity and stability has extended the potential for Dow Corning"s strength in Photonics to be deployed "in-car". Demonstration of board-level and back-plane solutions utilising siloxane waveguide technology offers new opportunities for systems designers to integrate optical components at low cost on diverse substrates. Coupled with work on simple waveguide technology for sensors and data communications applications this suite of materials and technology offerings is very potent in this sector. The harsh environment under hood and the very extreme thermal range that materials must sustain in vehicles due to both their engine and the climate is an applications specification that defines the siloxane advantage. For these passive optics applications the siloxanes very high clarity at the data-communications wavelengths coupled with extraordinary stability offers significant design advantage. The future development of Head-Up-Displays for instrumentation and data display will offer yet more opportunities to the siloxanes in Automotive Photonics.

  2. A photon-photon collider in a vacuum hohlraum

    NASA Astrophysics Data System (ADS)

    Pike, O. J.; Mackenroth, F.; Hill, E. G.; Rose, S. J.

    2014-06-01

    The ability to create matter from light is amongst the most striking predictions of quantum electrodynamics. Experimental signatures of this have been reported in the scattering of ultra-relativistic electron beams with laser beams, intense laser-plasma interactions and laser-driven solid target scattering. However, all such routes involve massive particles. The simplest mechanism by which pure light can be transformed into matter, Breit-Wheeler pair production (γγ' --> e+e-), has never been observed in the laboratory. Here, we present the design of a new class of photon-photon collider in which a gamma-ray beam is fired into the high-temperature radiation field of a laser-heated hohlraum. Matching experimental parameters to current-generation facilities, Monte Carlo simulations suggest that this scheme is capable of producing of the order of 105 Breit-Wheeler pairs in a single shot. This would provide the first realization of a pure photon-photon collider, representing the advent of a new type of high-energy physics experiment.

  3. Characterizations of InAs quantum dot lasers butt-joint coupled with silicon photonics waveguides

    NASA Astrophysics Data System (ADS)

    Wang, Zihao; Yao, Ruizhe; Preble, Stefan; Lee, Chi-Sen; Guo, Wei

    2016-03-01

    InAs quantum dot (QD) laser heterostructures are grown by molecular beam epitaxy (MBE) system on GaAs substrates and fabricated. The InAs QD lasers exhibit comparable properties of the state-of-the-art QD lasers with the threshold current density Jth and efficiency ηi of 475A/cm2 and 72.6%, respectively, at room temperature. The quantum dot laser emission is butt-joint coupled into silicon photonics waveguides by aligning the laser and silicon photonics chips with two translation stages. Due to the optical feedback to the laser cavity at the air/Si interface, the laser power self-pulsation and reduced threshold current density are observed. And the effective facet reflectivity, Reff, of 62.7% is obtained from the theoretically analysis of the laser characteristics. Furthermore, the silicon photonics waveguides interface is coated with the SiO2/TiO2 antireflection (AR) coating layers, and no laser performance interference is observed owing the reduced optical feedback.

  4. Characteristics of S12045(X) photon sensors for GlueX

    NASA Astrophysics Data System (ADS)

    Smith, E. S.; Qiang, Y.; Tolstukhin, I.; Brooks, W. K.; Hakobyan, H.; Kuleshov, S.; Soto, O.; Toro, A.

    2013-04-01

    The barrel calorimeter of the GlueX detector in Hall D at Jefferson Lab will be instrumented with 4000 large-area (1.2x1.2 cm^2) silicon photomultipliers (SiPMs) [1]. These photon sensors have properties similar to vacuum photomultipliers, but are unaffected by high magnetic fields. In our experiment, they will operate in magnetic fields exceeding 1,. After extensive tests with a variety of sensors, we chose the S12045(X) custom SiPM arrays manufactured by Hamamatsu Corporation, also known as multi-pixel photon counters (MPPCs) [2]. All production units have been delivered and we have measured the photon detection efficiency (PDE), gain, dark rate, cross talk and after pulsing at three different temperatures (5, 7 and 20^oC). We will present a summary of these measurements and the plan for use of these sensors in the GlueX experiment.[4pt] [1] F. Barbosa et al., NIM A695 (2012) 100.[0pt] [2] Y. Qiang et al., NIM A698 (2013) 234.

  5. Initial results from a prototype whole-body photon-counting computed tomography system

    NASA Astrophysics Data System (ADS)

    Yu, Z.; Leng, S.; Jorgensen, S. M.; Li, Z.; Gutjahr, R.; Chen, B.; Duan, X.; Halaweish, A. F.; Yu, L.; Ritman, E. L.; McCollough, C. H.

    2015-03-01

    X-ray computed tomography (CT) with energy-discriminating capabilities presents exciting opportunities for increased dose efficiency and improved material decomposition analyses. However, due to constraints imposed by the inability of photon-counting detectors (PCD) to respond accurately at high photon flux, to date there has been no clinical application of PCD-CT. Recently, our lab installed a research prototype system consisting of two x-ray sources and two corresponding detectors, one using an energy-integrating detector (EID) and the other using a PCD. In this work, we report the first third-party evaluation of this prototype CT system using both phantoms and a cadaver head. The phantom studies demonstrated several promising characteristics of the PCD sub-system, including improved longitudinal spatial resolution and reduced beam hardening artifacts, relative to the EID sub-system. More importantly, we found that the PCD sub-system offers excellent pulse pileup control in cases of x-ray flux up to 550 mA at 140 kV, which corresponds to approximately 2.5×1011 photons per cm2 per second. In an anthropomorphic phantom and a cadaver head, the PCD sub-system provided image quality comparable to the EID sub-system for the same dose level. Our results demonstrate the potential of the prototype system to produce clinically-acceptable images in vivo.

  6. A depth dependence determination of the wedge transmission factor for 4-10 MV photon beams.

    PubMed

    McCullough, E C; Gortney, J; Blackwell, C R

    1988-01-01

    The depth dependence (up to 25 cm) of the in-phantom wedge transmission factor (WTF) has been determined for three medical linear accelerator x-ray beams with energies of 4, 6, and 10 MV containing 15 degrees-60 degrees (nominal) brass wedges. All measurements were made with a cylindrical ionization chamber in water, for a field size of 10 X 10 cm2 with a source-skin distance of 80 or 100 cm. We conclude that, for the accelerators studied, the WTF factor at depth is less than 2% different from that determined at dmax (for the nominal wedge angles and photon energies studied) unless the depth of interest is greater than 10 cm. Up to the maximum depth studied (25 cm) the relative wedge factor--that is, wedge factor at depth compared to that determined at dmax--was about equal to or less than 1.02 for the 15 degrees and 30 degrees wedges and any of the photon beam energies studied. For the seldom utilized combination of a nominal wedge angle in excess of 45 degrees with a depth greater than 10 cm, the WTF at depth can differ from the WTF determined at dmax, by up to 5%. Since the wedge transmission factor is reflective of relative percent dose data, our results also indicate that it is in error to use open field percent depth doses for certain combinations of wedge angle, photon energy, and depth. PMID:3211057

  7. Development of an efficient scanning and purging magnet system for IMRT with narrow high energy photon beams

    NASA Astrophysics Data System (ADS)

    Andreassen, Björn; Svensson, Roger; Holmberg, Rickard; Danared, Håkan; Brahme, Anders

    2009-12-01

    transmitted and photon generated electrons. The simulations show that its is possible to have a scan area on the patient of up to 43×40 cm2 for an incident electron energy of 50 MeV and 28×40 cm2 at 75 MeV, while at the same time adequately deflecting the transmitted electron beam.

  8. Plasmonic gold nanocrystals coupled with photonic crystal seamlessly on TiO2 nanotube photoelectrodes for efficient visible light photoelectrochemical water splitting.

    PubMed

    Zhang, Zhonghai; Zhang, Lianbin; Hedhili, Mohamed Nejib; Zhang, Hongnan; Wang, Peng

    2013-01-01

    A visible light responsive plasmonic photocatalytic composite material is designed by rationally selecting Au nanocrystals and assembling them with the TiO(2)-based photonic crystal substrate. The selection of the Au nanocrystals is so that their surface plasmonic resonance (SPR) wavelength matches the photonic band gap of the photonic crystal and thus that the SPR of the Au receives remarkable assistance from the photonic crystal substrate. The design of the composite material is expected to significantly increase the Au SPR intensity and consequently boost the hot electron injection from the Au nanocrystals into the conduction band of TiO(2), leading to a considerably enhanced water splitting performance of the material under visible light. A proof-of-concept example is provided by assembling 20 nm Au nanocrystals, with a SPR peak at 556 nm, onto the photonic crystal which is seamlessly connected on TiO(2) nanotube array. Under visible light illumination (>420 nm), the designed material produced a photocurrent density of ~150 μA cm(-2), which is the highest value ever reported in any plasmonic Au/TiO(2) system under visible light irradiation due to the photonic crystal-assisted SPR. This work contributes to the rational design of the visible light responsive plasmonic photocatalytic composite material based on wide band gap metal oxides for photoelectrochemical applications.

  9. Large Area 2D and 3D Colloidal Photonic Crystals Fabricated by a Roll-to-Roll Langmuir-Blodgett Method.

    PubMed

    Parchine, Mikhail; McGrath, Joe; Bardosova, Maria; Pemble, Martyn E

    2016-06-14

    We present our results on the fabrication of large area colloidal photonic crystals on flexible poly(ethylene terephthalate) (PET) film using a roll-to-roll Langmuir-Blodgett technique. Two-dimensional (2D) and three-dimensional (3D) colloidal photonic crystals from silica nanospheres (250 and 550 nm diameter) with a total area of up to 340 cm(2) have been fabricated in a continuous manner compatible with high volume manufacturing. In addition, the antireflective properties and structural integrity of the films have been enhanced via the use of a second roll-to-roll process, employing a slot-die coating of an optical adhesive over the photonic crystal films. Scanning electron microscopy images, atomic force microscopy images, and UV-vis optical transmission and reflection spectra of the fabricated photonic crystals are analyzed. This analysis confirms the high quality of the 2D and 3D photonic crystals fabricated by the roll-to-roll LB technique. Potential device applications of the large area 2D and 3D colloidal photonic crystals on flexible PET film are briefly reviewed. PMID:27218474

  10. Large Area 2D and 3D Colloidal Photonic Crystals Fabricated by a Roll-to-Roll Langmuir-Blodgett Method.

    PubMed

    Parchine, Mikhail; McGrath, Joe; Bardosova, Maria; Pemble, Martyn E

    2016-06-14

    We present our results on the fabrication of large area colloidal photonic crystals on flexible poly(ethylene terephthalate) (PET) film using a roll-to-roll Langmuir-Blodgett technique. Two-dimensional (2D) and three-dimensional (3D) colloidal photonic crystals from silica nanospheres (250 and 550 nm diameter) with a total area of up to 340 cm(2) have been fabricated in a continuous manner compatible with high volume manufacturing. In addition, the antireflective properties and structural integrity of the films have been enhanced via the use of a second roll-to-roll process, employing a slot-die coating of an optical adhesive over the photonic crystal films. Scanning electron microscopy images, atomic force microscopy images, and UV-vis optical transmission and reflection spectra of the fabricated photonic crystals are analyzed. This analysis confirms the high quality of the 2D and 3D photonic crystals fabricated by the roll-to-roll LB technique. Potential device applications of the large area 2D and 3D colloidal photonic crystals on flexible PET film are briefly reviewed.

  11. Engineering a factorable photon pair source

    SciTech Connect

    Zielnicki, Kevin; Kwiat, Paul

    2014-12-04

    Spontaneous parametric downconversion is an important process for producing pairs of photons for quantum optics. We discuss a scheme for eliminating undesired inter-photon correlations inherent in this process, and an efficient characterization of spectral correlations.

  12. Nuclear Resonance Fluorescence Using Different Photon Sources

    SciTech Connect

    Warren, Glen A.; Caggiano, Joseph A.; Ahmed, Mohammad; Bertozzi, William; Hunt, Alan W.; Johnson, James; Jones, James L.; Korbly, Steve; Reedy, Edward; Seipel, Heather; Stave, Sean; Watson, Scott; Weller, Henry

    2008-11-14

    Abstract–Nuclear resonance fluorescence (NRF) is a photon-based active interrogation approach that provides isotope-specific signatures that can be used to detect and characterize samples. As NRF systems are designed to address specific appli¬cations, an obvious first question to address is the type of photon source to be employed for the application. Our collaboration has conducted a series of NRF measurements using different photon sources to begin to examine this issue. The measurements were designed to be as similar as possible to facilitate a straightforward comparison of the different sources. Measurements were conducted with a high-duty factor electron accelerator using bremsstrahlung photons, with a pulsed linear accelerator using bremsstrahlung photons, and with a narrow bandwidth photon source using Compton backscattered photons. We present our observations on the advantages and disadvantages of each photon source type. Issues such as signal rate, the signal-to-noise ratio, and absorbed dose are discussed.

  13. 2004 Photon Correlation and Scattering Conference

    NASA Technical Reports Server (NTRS)

    Meyer, William (Editor); Smart, Anthony (Editor); Wegdam, Gerard (Editor); Dogariu, Aristide (Editor); Carpenter, Bradley (Editor)

    2004-01-01

    The Photon Correlation and Scattering (PCS) meeting welcomes all who are interested in the art and science of photon correlation and its application to optical scattering. The meeting is intended to enhance interactions between theory, applications, instrument design, and participants.

  14. Photonic crystal surface-emitting lasers

    SciTech Connect

    Chua, Song Liang; Lu, Ling; Soljacic, Marin

    2015-06-23

    A photonic-crystal surface-emitting laser (PCSEL) includes a gain medium electromagnetically coupled to a photonic crystal whose energy band structure exhibits a Dirac cone of linear dispersion at the center of the photonic crystal's Brillouin zone. This Dirac cone's vertex is called a Dirac point; because it is at the Brillouin zone center, it is called an accidental Dirac point. Tuning the photonic crystal's band structure (e.g., by changing the photonic crystal's dimensions or refractive index) to exhibit an accidental Dirac point increases the photonic crystal's mode spacing by orders of magnitudes and reduces or eliminates the photonic crystal's distributed in-plane feedback. Thus, the photonic crystal can act as a resonator that supports single-mode output from the PCSEL over a larger area than is possible with conventional PCSELs, which have quadratic band edge dispersion. Because output power generally scales with output area, this increase in output area results in higher possible output powers.

  15. Photonic technologies for visual implants

    NASA Astrophysics Data System (ADS)

    Buss, Ruediger; Praemassing, F.; Puettjer, D.; Stawski, N.; Jaeger, Dieter

    2003-02-01

    In this paper two applications of photonic technologies for visual implants in the field of medicine are presented. Both are technical systems working as vision aid for people suffering from blindness due to damages in their visual system. The first system is a retinal implant (RI), the second an intraocular vision aid (IoVA) for people with opaque cornea.

  16. [Photonic crystals for analytical chemistry].

    PubMed

    Chen, Yi; Li, Jincheng

    2009-09-01

    Photonic crystals, originally created to control the transmission of light, have found their increasing value in the field of analytical chemistry and are probable to become a hot research area soon. This review is hence composed, focusing on their analytical chemistry-oriented applications, including especially their use in chromatography, capillary- and chip-based electrophoresis.

  17. Direct photon experiment at POLEX

    SciTech Connect

    Ohashi, Y.

    1989-01-01

    Significant contribution of the gluons to the proton spin has been suggested by several authors to explain the recent EMC results on the spin dependent structure function of proton. Direct photon measurements at large transverse momentum in pp reactions with pure initial helicity states is proposed in this paper in order to study spin dependent gluon structure function. 8 refs., 3 figs., 1 tab.

  18. Photonic spin filter with dielectric metasurfaces.

    PubMed

    Ke, Yougang; Liu, Yachao; Zhou, Junxiao; Liu, Yuanyuan; Luo, Hailu; Wen, Shuangchun

    2015-12-28

    We propose a photonic spin filter whose structure is similar to that of conventional spatial filter, but the two plano-convex lenses are replaced by Pancharatnam-Berry phase ones. The dielectric metasurface with high transmission and conversion efficiency is designed to work as Pancharatnam-Berry phase lens. The photonic spin filter can sort desired spin photons from the input beam with mixed spin states, and thereby facilitate possible applications in spin-based photonics. PMID:26831976

  19. Single-photon-sensitive linear-mode APD ladar receiver developments

    NASA Astrophysics Data System (ADS)

    Williams, George M.; Compton, Madison A.; Huntington, Andrew S.

    2008-04-01

    New measurements are presented for multi-stage InGaAs avalanche photodiodes (APDs) which have the potential to perform GHz-rate single photon counting in linear mode. No increase in dark current was measured for an 11-device sample of 5-stage APDs following 717 hours of accelerated aging under bias at 50°C, during an initial lifetime study. Impulse response times of 0.45 ns, 0.9 ns, and 1.1 ns were measured directly for 6-, 8-, and 10-stage APDs, respectively, operated at a nominal gain of M=10. To assess the suitability of the technology for a NASA optical communications application, separate samples of 5-stage APDs were irradiated by 1- and 2-MeV protons at the University of Washington's Center for Experimental Nuclear Physics and Astrophysics (UW CENPA) and by 63.5-MeV protons at the University of California Davis, Crocker Nuclear Laboratory (UCD CNL). Good agreement between calculated non-ionizing energy loss (NIEL) and observed damage was found for the low-energy protons at fluences of 10 10 and 10 11 cm -2. A NIEL calculation successfully predicted the damage observed following a 5×10 10 cm -2 dose of 63.5-MeV protons by extrapolating from 2 MeV data, which suggests that displacement damage is the dominant mechanism.

  20. Two-photon excitation of aluminium phthalocyanines

    SciTech Connect

    Meshalkin, Yu P; Alfimov, E E; Makukha, V K; Vasil'ev, N E; Denisov, A N; Ogirenko, A P

    1999-12-31

    A demonstration is given of the feasibility of two-photon excitation of aluminium phthalocyanine and of the pharmaceutical preparation 'Fotosens', used in photodynamic therapy. The excitation source was an Nd:YAG laser emitting at the 1064 nm wavelength. The spectra of the two-photon-excited luminescence were obtained and the two-photon absorption cross sections were determined. (lasers in medicine)

  1. Integrated Photonics Research: Post-deadline papers

    NASA Astrophysics Data System (ADS)

    Quinn, Jarus W.

    1993-03-01

    The symposium was held on the following topics: advanced solid state lasers, compact blue-green lasers, integrated photonics research, nonlinear guide-wave optics, optical amplifiers and their applications, optical design for photonics, photonics in switching, quantum optoelectronics, short-wavelength -- physics with intense-laser pulses, soft x-ray protection lithography, ultrafast electronics and optoelectronics, optical computing, and spatial light modulators.

  2. Thermodynamic Laws of Neutrino and Photon Emission.

    ERIC Educational Resources Information Center

    Walsh, P. J.; Gallo, C. F.

    1980-01-01

    Compares neutrino and photon emissions, develops the thermodynamic blackbody laws of neutrino emission analogous to laws governing photon emission, points out that combined radiation from a "true blackbody" consists of both photon and neutrino emissions of comparable magnitude, and speculates upon the existence of blackbody neutrino emitters in…

  3. Photonics for MS study in radiocommunications

    NASA Astrophysics Data System (ADS)

    Volner, Rudolf; Klima, Milos; Ticha, Dasa

    2002-05-01

    The paper is devoted to an education of Photonics at the Dept. of Telecommunications, Faculty of Electrical Engineering, at the University of Zilina. Originated from the university historical development the photonic subjects are implemented in two basic areas: Telecommunication Technology and Radiocommunication Technology. From the school year 1994/95 the new subject Photonics has been taught and it has attracted numerous students. The subject is focused on both physical principles and system application. The relevant parts can be listed as: interaction photon - matter, photonic receivers and transmitters, modulation and demodulation in Photonics, photonic networks - narrowband and wideband, photonic switches, image sensors and displays. The education of Photonics has been supported by research activities in the field of applied photonic system for signal (data) transmission and selected results have been implemented into the subject structure. The paper listed a detailed content of the subject in two fields: lectures and experimental laboratory exercises. As an integral part of the course we plan to implement selected experiments from the area of 2D photonic (image) processing and to expand the imaging photonic part.

  4. Lateral cavity photonic crystal surface emitting lasers with ultralow threshold and large power

    NASA Astrophysics Data System (ADS)

    Wang, Yufei; Qu, Hongwei; Zhou, Wenjun; Jiang, Bin; Zhang, Jianxin; Qi, Aiyi; Liu, Lei; Fu, Feiya; Zheng, Wanhua

    2012-03-01

    The Bragg diffraction condition of surface-emitting lasing action is analyzed and Γ2-1 mode is chosen for lasing. Two types of lateral cavity photonic crystal surface emitting lasers (LC-PCSELs) based on the PhC band edge mode lateral resonance and vertical emission to achieve electrically driven surface emitting laser without distributed Bragg reflectors in the long wavelength optical communication band are designed and fabricated. Deep etching techniques, which rely on the active layer being or not etched through, are adopted to realize the LC-PCSELs on the commercial AlGaInAs/InP multi-quantum-well (MQW) epitaxial wafer. 1553.8 nm with ultralow threshold of 667 A/cm2 and 1575 nm with large power of 1.8 mW surface emitting lasing actions are observed at room temperature, providing potential values for mass production with low cost of electrically driven PCSELs.

  5. Irradiation of the CLARO-CMOS chip, a fast ASIC for single-photon counting

    NASA Astrophysics Data System (ADS)

    Andreotti, M.; Baldini, W.; Calabrese, R.; Carniti, P.; Cassina, L.; Cotta Ramusino, A.; Fiorini, M.; Giachero, A.; Gotti, C.; Luppi, E.; Maino, M.; Malaguti, R.; Pessina, G.; Tomassetti, L.

    2015-07-01

    The CLARO-CMOS is a prototype ASIC that allows fast photon counting with low power consumption, built in AMS 0.35 μm CMOS technology. It is intended to be used as a front-end readout for the upgraded LHCb RICH detectors. In this environment, assuming 10 years of operation at the nominal luminosity expected after the upgrade, the ASIC must withstand a total fluence of about 6×1012 1 MeV neq/cm2 and a total ionising dose of 400 krad. Long term stability of the electronics front-end is essential and the effects of radiation damage on the CLARO-CMOS performance must be carefully studied. This paper describes results of multi-step irradiation tests with protons up to the dose of ~8 Mrad, including measurement of single event effects during irradiation and chip performance evaluation before and after each irradiation step.

  6. Measuring the two-photon decay width of intermediate-mass Higgs bosons at a photon-photon collider

    SciTech Connect

    Ohgaki, T.; Takahashi, T.; Watanabe, I.

    1997-08-01

    The feasibility of a measurement of the partial decay width of the intermediate-mass Higgs boson into two photons at a photon-photon collider is studied by a simulation. The QCD radiative correction for quark pair background processes is taken into account for the realistic background estimation. It is found that the two-photon decay width can be measured with the statistical error of 7.6{percent} with about one year of experiment. The impact of the measurement of the two-photon decay width to look for the new physics beyond is demonstrated. {copyright} {ital 1997} {ital The American Physical Society}

  7. Spying on photons with photons: quantum interference and information

    NASA Astrophysics Data System (ADS)

    Ataman, Stefan

    2016-07-01

    The quest to have both which-path knowledge and interference fringes in a double-slit experiment dates back to the inception of quantum mechanics (QM) and to the famous Einstein-Bohr debates. In this paper we propose and discuss an experiment able to spy on one photon's path with another photon. We modify the quantum state inside the interferometer as opposed to the traditional physical modification of the "wave-like" or "particle-like" experimental setup. We are able to show that it is the ability to harvest or not which-path information that finally limits the visibility of the interference pattern and not the "wave-like" or "particle-like" experimental setups. Remarkably, a full "particle-like" experimental setup is able to show interference fringes with 100% visibility if the quantum state is carefully engineered.

  8. Photonic Doppler Velocimetry Multiplexing Techniques: Evaluation of Photonic Techniques

    SciTech Connect

    Edward Daykin

    2012-05-24

    This poster reports progress related to photonic technologies. Specifically, the authors developed diagnostic system architecture for a Multiplexed Photonic Doppler Velocimetry (MPDV) that incorporates frequency and time-division multiplexing into existing PDV methodology to provide increased channel count. Current MPDV design increases number of data records per digitizer channel 8x, and also operates as a laser-safe (Class 3a) system. Further, they applied heterodyne interferometry to allow for direction-of-travel determination and enable high-velocity measurements (>10 km/s) via optical downshifting. They also leveraged commercially available, inexpensive and robust components originally developed for telecom applications. Proposed MPDV architectures employ only commercially available, fiber-coupled hardware.

  9. Characterization of photon statistics in a single-photon source via variable attenuation

    SciTech Connect

    Zhang Shengli; Zou Xubo; Li Chuanfeng; Guo Guangcan; Jin Chenhui

    2009-10-15

    We propose a simple but effective scheme for characterizing photon-number statistics of a practical single-photon source. In this scheme, the variable attenuation method which frequently appears in decoy state quantum cryptography is utilized here to enhance the estimation of photon-number statistics. A much stricter bound for vacuum and single-photon proportions is obtained and this result, in turn, is shown to be applicable to the unconditional secure quantum cryptographic communication with single-photon devices.

  10. High-Energy QCD Asymptotics of Photon--Photon Collisions

    SciTech Connect

    Brodsky, Stanley J.

    2002-07-26

    The high-energy behavior of the total cross section for highly virtual photons, as predicted by the BFKL equation at next-to-leading order (NLO) in QCD, is discussed. The NLO BFKL predictions, improved by the BLM optimal scale setting, are in good agreement with recent OPAL and L3 data at CERN LEP2. NLO BFKL predictions for future linear colliders are presented.

  11. Passive silicon photonic devices for microwave photonic signal processing

    NASA Astrophysics Data System (ADS)

    Wu, Jiayang; Peng, Jizong; Liu, Boyu; Pan, Ting; Zhou, Huanying; Mao, Junming; Yang, Yuxing; Qiu, Ciyuan; Su, Yikai

    2016-08-01

    We present our recent progress on microwave signal processing (MSP) using on-chip passive silicon photonic devices, including tunable microwave notch filtering/millimeter-wave (MMW) signal generation based on self-coupled micro-resonators (SCMRs), and tunable radio-frequency (RF) phase shifting implemented by a micro-disk resonator (MDR). These schemes can provide improved flexibility and performances of MSP. The experimental results are in good agreement with theoretical predictions, which validate the effectiveness of the proposed schemes.

  12. Photon induced L3 vacancy alignment at tuned photon energies

    NASA Astrophysics Data System (ADS)

    Bansal, Himani; Kaur, Gurpreet; Tiwari, Manoj K.; Mittal, Raj

    2016-04-01

    Photon induced L3 X-ray measurements for Lα/Lℓ cross-section ratios in elements, 66 ⩽ Z ⩽ 83, at tuned photon energies on synchrotron Beamline-16 at Indus-2, India have been used to study the effect of Coster-Kronig (CK) transitions and photon energies on alignment of L3 vacancies. Certainty and reliability of the measurements were checked from comparison of measured Lα and Lℓ fluorescence cross-sections at E1 excitation with available theoretical/empirical/experimental values that required additional measurements for source, geometry and efficiency factor S0GɛLα/ℓ in the used set-up. Fall/rise trend of the ratios with energy for different Z's was found to resemble the off/on-set pattern of CK transitions as pointed out by Bambynek et al. and Campbell. Evaluated alignment parameter A2 values are very much within the limits, 0.05

  13. Topological photonic crystal with equifrequency Weyl points

    NASA Astrophysics Data System (ADS)

    Wang, Luyang; Jian, Shao-Kai; Yao, Hong

    2016-06-01

    Weyl points in three-dimensional photonic crystals behave as monopoles of Berry flux in momentum space. Here, based on general symmetry analysis, we show that a minimal number of four symmetry-related (consequently equifrequency) Weyl points can be realized in time-reversal invariant photonic crystals. We further propose an experimentally feasible way to modify double-gyroid photonic crystals to realize four equifrequency Weyl points, which is explicitly confirmed by our first-principle photonic band-structure calculations. Remarkably, photonic crystals with equifrequency Weyl points are qualitatively advantageous in applications including angular selectivity, frequency selectivity, invisibility cloaking, and three-dimensional imaging.

  14. Topological photonic crystal with ideal Weyl points

    NASA Astrophysics Data System (ADS)

    Wang, Luyang; Jian, Shao-Kai; Yao, Hong

    Weyl points in three-dimensional photonic crystals behave as monopoles of Berry flux in momentum space. Here, based on symmetry analysis, we show that a minimal number of symmetry-related Weyl points can be realized in time-reversal invariant photonic crystals. We propose to realize these ``ideal'' Weyl points in modified double-gyroid photonic crystals, which is confirmed by our first-principle photonic band-structure calculations. Photonic crystals with ideal Weyl points are qualitatively advantageous in applications such as angular and frequency selectivity, broadband invisibility cloaking, and broadband 3D-imaging.

  15. Photon doses in NPL standard neutron fields.

    PubMed

    Roberts, N J; Horwood, N A; McKay, C J

    2014-10-01

    Standard neutron fields are invariably accompanied by a photon component due to the neutron-generating reactions and secondary neutron interactions in the surrounding environment. A set of energy-compensated Geiger-Müller (GM) tubes and electronic personal dosemeters (EPDs) have been used to measure the photon dose rates in a number of standard radionuclide and accelerator-based neutron fields. The GM tubes were first characterised in standard radioisotope and X-ray photon fields and then modelled using MCNP to determine their photon dose response as a function of energy. Values for the photon-to-neutron dose equivalent ratios are presented and compared with other published values.

  16. Evanescent wave of a single photon

    NASA Astrophysics Data System (ADS)

    Li, Hongrui

    2013-07-01

    A photon model is proposed, and the parameter equations of the photon are obtained. This model can explain the polarization, total reflection, evanescent wave, and Goos-Hanchen shift of a single photon. The evanescent waves of photons with different frequencies are refractively dispersed. The Goos-Hanchen shift is dependent on the difference between the two refractive indices of media, the incident angle, and the frequency of the photon. According to this model, an evanescent wave of light does not decay exponentially along the z direction and does not propagate along the x direction infinitely. The laws of refraction and reflection for a single photon can be derived. The refractive dispersion of light can be explained. According to this model, every photon is polarized. Polarization is the intrinsic nature of the photon. The motion of a single photon is either clockwise or counterclockwise. The so-called unpolarized light refers to light that consists of an equal number of photons with clockwise motion and counterclockwise motion. The trajectories of two photons with the same frequency but opposite spiral directions are mirror-image isomers. They cannot be superimposed upon each other.

  17. Photonics with multiwall carbon nanotube arrays.

    PubMed

    Lidorikis, Elefterios; Ferrari, Andrea C

    2009-05-26

    We investigate the photonic properties of two-dimensional nanotube arrays for photon energies up to 40 eV and unveil the physics of two distinct applications: deep-UV photonic crystals and total visible absorbers. We find three main regimes: for small intertube spacing of 20-30 nm, we obtain strong Bragg scattering and photonic band gaps in the deep-UV range of 25 approximately 35 eV. For intermediate spacing of 40-100 nm, the photonic bands anticross with the graphite plasmon bands resulting into a complex photonic structure, and a generally reduced Bragg scattering. For large spacing >150 nm, the Bragg gap moves into the visible and decreases due to absorption. This leads to nanotube arrays behaving as total optical absorbers. Our results can guide the design of photonic applications in the visible and deep UV ranges.

  18. Tunable resonant structures for photonic integrated circuits

    NASA Astrophysics Data System (ADS)

    Ptasinski, Joanna Nina

    Photonics is an evolving field allowing for optical devices to be made cost effectively using standard semiconductor fabrication techniques, which in turn enables integration with microelectronic chips. Chip scale photonics will play an increasing role in the future of communications as the demand for bandwidth and reduced power consumption per bit continues to grow. Tunable optical circuit components are one of the essential technologies in the development of photonic analogues for classical electronic devices, where tunable photonic resonant structures allow for altering of their electromagnetic spectrum and find applications in optical switching, filtering, buffering, lasers and biosensors. The scope of this work is focused on tunable resonant structures for photonic integrated circuits. Specifically, this work demonstrates active tuning of silicon photonic resonant structures using the properties of dye doped nematic liquid crystals, temperature stabilization of silicon photonics using the passive properties of liquid crystals, and the effects of low density plasma enhanced chemical vapor deposition (PECVD) claddings on ring resonator device performance.

  19. Sudakov effects in photon-initiated processes

    NASA Astrophysics Data System (ADS)

    Harland-Lang, L. A.; Khoze, V. A.; Ryskin, M. G.

    2016-10-01

    We consider the effect of the Sudakov factor in photon-initiated processes, corresponding to the no branching probability for the initial-state photon. We demonstrate how such a factor follows simply from the solution of the DGLAP equation for the photon PDF, and is therefore included automatically by this. We use this result to argue that the appropriate scale for the QED coupling α associated with an initial-state photon is not the virtuality of the photon, but rather the factorization scale at which the photon PDF is evaluated, and therefore that the use of the on-shell renormalization scheme is not appropriate for such processes. We also discuss exclusive photon-initiated processes, and demonstrate that no explicit Sudakov factor is required in this case.

  20. The low-energy photon tagger NEPTUN

    NASA Astrophysics Data System (ADS)

    Savran, D.; Lindenberg, K.; Glorius, J.; Löher, B.; Müller, S.; Pietralla, N.; Schnorrenberger, L.; Simon, V.; Sonnabend, K.; Wälzlein, C.; Elvers, M.; Endres, J.; Hasper, J.; Zilges, A.

    2010-02-01

    A new photon tagging spectrometer was built at the superconducting Darmstadt electron linear accelerator (S-DALINAC). The system is designed for tagging photons in an energy range from 6 to 20 MeV with the emphasis on best possible energy resolution and intensity. The absolute energy resolution of photons at 10 MeV is expected to be about 20 keV. With scintillating fibres as focal-plane detectors a maximum rate of tagged photons of 104 keV -1s -1 will be achieved. Detailed design studies including Monte Carlo simulations are presented, as well as results for the measured tagged photon energy profile of the system realized so far. This photon-tagging facility will allow to determine the photon absorption cross-sections as a function of excitation energy and to study the decay patterns of nuclear photo-excitations in great detail.

  1. Photon acceleration in plasma wake wave

    SciTech Connect

    Bu, Zhigang; Shen, Baifei Yi, Longqing; Zhang, Hao; Huang, Shan; Li, Shun

    2015-04-15

    The photon acceleration effect in a laser wake field is investigated based on photon Hamiltonian dynamics. A test laser pulse is injected into a plasma wave at an incident angle θ{sub i}, which could slow down the photon velocity along the propagating direction of the wake wave so as to increase the acceleration distance for the photons. The photon trapping condition is analyzed in detail, and the maximum frequency shift of the trapped photon is obtained. The acceleration gradient and dephasing length are emphatically studied. The compression of the test laser pulse is examined and used to interpret the acceleration process. The limit of finite transverse width of the wake wave on photon acceleration is also discussed.

  2. Photonics based on carbon nanotubes

    PubMed Central

    2013-01-01

    Among direct-bandgap semiconducting nanomaterials, single-walled carbon nanotubes (SWCNT) exhibit strong quasi-one-dimensional excitonic optical properties, which confer them a great potential for their integration in future photonics devices as an alternative solution to conventional inorganic semiconductors. In this paper, we will highlight SWCNT optical properties for passive as well as active applications in future optical networking. For passive applications, we directly compare the efficiency and power consumption of saturable absorbers (SAs) based on SWCNT with SA based on conventional multiple quantum wells. For active applications, exceptional photoluminescence properties of SWCNT, such as excellent light-emission stabilities with temperature and excitation power, hold these nanometer-scale materials as prime candidates for future active photonics devices with superior performances. PMID:23803293

  3. Photon upconversion with directed emission.

    PubMed

    Börjesson, K; Rudquist, P; Gray, V; Moth-Poulsen, K

    2016-01-01

    Photon upconversion has the potential to increase the efficiency of single bandgap solar cells beyond the Shockley Queisser limit. Efficient light management is an important point in this context. Here we demonstrate that the direction of upconverted emission can be controlled in a reversible way, by embedding anthracene derivatives together with palladium porphyrin in a liquid crystalline matrix. The system is employed in a triplet-triplet annihilation photon upconversion scheme demonstrating controlled switching of directional anti Stokes emission. Using this approach an emission ratio of 0.37 between the axial and longitudinal emission directions and a directivity of 1.52 is achieved, reasonably close to the theoretical maximal value of 2 obtained from a perfectly oriented sample. The system can be switched for multiple cycles without any visible degradation and the speed of switching is only limited by the intrinsic rate of alignment of the liquid crystalline matrix. PMID:27573539

  4. Photonics classes in high school

    NASA Astrophysics Data System (ADS)

    John, Pearl V.; Shanks, Richard A.

    2002-05-01

    In continuing the development of a three-year high school photonics program, the Columbia Area Career Center (Missouri, USA) faces the challenges associated with introducing a new subject area to career technical education in the public school system. The program was established to address the severe lack of Laser Electro-Optical Technicians (LEOTs) in the local manufacturing industry. Its goals are to increase student awareness of the expanding job opportunities available in photonics and optics, teach skills needed for the field, and foster close ties with industry and post-secondary institutions. This paper examines the success of the program to date and outlines the problems associated with teaching an advanced curriculum at the high school level.

  5. Photonic band gap structure simulator

    DOEpatents

    Chen, Chiping; Shapiro, Michael A.; Smirnova, Evgenya I.; Temkin, Richard J.; Sirigiri, Jagadishwar R.

    2006-10-03

    A system and method for designing photonic band gap structures. The system and method provide a user with the capability to produce a model of a two-dimensional array of conductors corresponding to a unit cell. The model involves a linear equation. Boundary conditions representative of conditions at the boundary of the unit cell are applied to a solution of the Helmholtz equation defined for the unit cell. The linear equation can be approximated by a Hermitian matrix. An eigenvalue of the Helmholtz equation is calculated. One computation approach involves calculating finite differences. The model can include a symmetry element, such as a center of inversion, a rotation axis, and a mirror plane. A graphical user interface is provided for the user's convenience. A display is provided to display to a user the calculated eigenvalue, corresponding to a photonic energy level in the Brilloin zone of the unit cell.

  6. Superdense teleportation using hyperentangled photons.

    PubMed

    Graham, Trent M; Bernstein, Herbert J; Wei, Tzu-Chieh; Junge, Marius; Kwiat, Paul G

    2015-01-01

    Transmitting quantum information between two remote parties is a requirement for many quantum applications; however, direct transmission of states is often impossible because of noise and loss in the communication channel. Entanglement-enhanced state communication can be used to avoid this issue, but current techniques require extensive experimental resources to transmit large quantum states deterministically. To reduce these resource requirements, we use photon pairs hyperentangled in polarization and orbital angular momentum to implement superdense teleportation, which can communicate a specific class of single-photon ququarts. We achieve an average fidelity of 87.0(1)%, almost twice the classical limit of 44% with reduced experimental resources than traditional techniques. We conclude by discussing the information content of this constrained set of states and demonstrate that this set has an exponentially larger state space volume than the lower-dimensional general states with the same number of state parameters. PMID:26018201

  7. Photon upconversion with directed emission

    PubMed Central

    Börjesson, K.; Rudquist, P.; Gray, V.; Moth-Poulsen, K.

    2016-01-01

    Photon upconversion has the potential to increase the efficiency of single bandgap solar cells beyond the Shockley Queisser limit. Efficient light management is an important point in this context. Here we demonstrate that the direction of upconverted emission can be controlled in a reversible way, by embedding anthracene derivatives together with palladium porphyrin in a liquid crystalline matrix. The system is employed in a triplet-triplet annihilation photon upconversion scheme demonstrating controlled switching of directional anti Stokes emission. Using this approach an emission ratio of 0.37 between the axial and longitudinal emission directions and a directivity of 1.52 is achieved, reasonably close to the theoretical maximal value of 2 obtained from a perfectly oriented sample. The system can be switched for multiple cycles without any visible degradation and the speed of switching is only limited by the intrinsic rate of alignment of the liquid crystalline matrix. PMID:27573539

  8. Transverse angular momentum of photons

    SciTech Connect

    Aiello, Andrea

    2010-05-15

    We develop the quantum theory of transverse angular momentum of light beams. The theory applies to paraxial and quasiparaxial photon beams in vacuum and reproduces the known results for classical beams when applied to coherent states of the field. Both the Poynting vector, alias the linear momentum, and the angular-momentum quantum operators of a light beam are calculated including contributions from first-order transverse derivatives. This permits a correct description of the energy flow in the beam and the natural emergence of both the spin and the angular momentum of the photons. We show that for collimated beams of light, orbital angular-momentum operators do not satisfy the standard commutation rules. Finally, we discuss the application of our theory to some concrete cases.

  9. Superdense teleportation using hyperentangled photons

    PubMed Central

    Graham, Trent M.; Bernstein, Herbert J.; Wei, Tzu-Chieh; Junge, Marius; Kwiat, Paul G

    2015-01-01

    Transmitting quantum information between two remote parties is a requirement for many quantum applications; however, direct transmission of states is often impossible because of noise and loss in the communication channel. Entanglement-enhanced state communication can be used to avoid this issue, but current techniques require extensive experimental resources to transmit large quantum states deterministically. To reduce these resource requirements, we use photon pairs hyperentangled in polarization and orbital angular momentum to implement superdense teleportation, which can communicate a specific class of single-photon ququarts. We achieve an average fidelity of 87.0(1)%, almost twice the classical limit of 44% with reduced experimental resources than traditional techniques. We conclude by discussing the information content of this constrained set of states and demonstrate that this set has an exponentially larger state space volume than the lower-dimensional general states with the same number of state parameters. PMID:26018201

  10. Photon upconversion with directed emission

    NASA Astrophysics Data System (ADS)

    Börjesson, K.; Rudquist, P.; Gray, V.; Moth-Poulsen, K.

    2016-08-01

    Photon upconversion has the potential to increase the efficiency of single bandgap solar cells beyond the Shockley Queisser limit. Efficient light management is an important point in this context. Here we demonstrate that the direction of upconverted emission can be controlled in a reversible way, by embedding anthracene derivatives together with palladium porphyrin in a liquid crystalline matrix. The system is employed in a triplet-triplet annihilation photon upconversion scheme demonstrating controlled switching of directional anti Stokes emission. Using this approach an emission ratio of 0.37 between the axial and longitudinal emission directions and a directivity of 1.52 is achieved, reasonably close to the theoretical maximal value of 2 obtained from a perfectly oriented sample. The system can be switched for multiple cycles without any visible degradation and the speed of switching is only limited by the intrinsic rate of alignment of the liquid crystalline matrix.

  11. Photon spectra from WIMP annihilation

    SciTech Connect

    Cembranos, J. A. R.; Cruz-Dombriz, A. de la; Dobado, A.; Maroto, A. L.; Lineros, R. A.

    2011-04-15

    If the present dark matter in the Universe annihilates into standard model particles, it must contribute to the fluxes of cosmic rays that are detected on the Earth and, in particular, to the observed gamma-ray fluxes. The magnitude of such a contribution depends on the particular dark matter candidate, but certain features of the produced photon spectra may be analyzed in a rather model-independent fashion. In this work we provide the complete photon spectra coming from WIMP annihilation into standard model particle-antiparticle pairs obtained by extensive Monte Carlo simulations. We present results for each individual annihilation channel and provide analytical fitting formulas for the different spectra for a wide range of WIMP masses.

  12. Superdense teleportation using hyperentangled photons.

    PubMed

    Graham, Trent M; Bernstein, Herbert J; Wei, Tzu-Chieh; Junge, Marius; Kwiat, Paul G

    2015-01-01

    Transmitting quantum information between two remote parties is a requirement for many quantum applications; however, direct transmission of states is often impossible because of noise and loss in the communication channel. Entanglement-enhanced state communication can be used to avoid this issue, but current techniques require extensive experimental resources to transmit large quantum states deterministically. To reduce these resource requirements, we use photon pairs hyperentangled in polarization and orbital angular momentum to implement superdense teleportation, which can communicate a specific class of single-photon ququarts. We achieve an average fidelity of 87.0(1)%, almost twice the classical limit of 44% with reduced experimental resources than traditional techniques. We conclude by discussing the information content of this constrained set of states and demonstrate that this set has an exponentially larger state space volume than the lower-dimensional general states with the same number of state parameters.

  13. Magnetic Mesoporous Photonic Cellulose Films.

    PubMed

    Giese, Michael; Blusch, Lina K; Schlesinger, Maik; Meseck, Georg R; Hamad, Wadood Y; Arjmand, Mohammad; Sundararaj, Uttandaraman; MacLachlan, Mark J

    2016-09-13

    Novel hybrid materials of cellulose and magnetic nanoparticles (NPs) were synthesized and characterized. The materials combine the chiral nematic structural features of mesoporous photonic cellulose (MPC) with the magnetic properties of cobalt ferrite (CoFe2O4). The photonic, magnetic, and dielectric properties of the hybrid materials were investigated during the dynamic swelling and deswelling of the MPC films. It was observed that the dielectric properties of the generated MPC films increased tremendously following swelling in water, endorsing efficient swelling ability of the generated mesoporous films. The high magnetic permeability of the developed MPC films in conjunction with their superior dielectric properties, predominantly in the swollen state, makes them interesting for electromagnetic interference shielding applications. PMID:27588561

  14. Discrete photonics in waveguide arrays.

    PubMed

    Moison, J M; Belabas, N; Minot, C; Levenson, J A

    2009-08-15

    In homogeneous arrays of coupled waveguides, Floquet-Bloch waves are known to travel freely across the waveguides. We introduce a systematic discussion of the built-in patterning of the coupling constant between neighboring waveguides. Key patterns provide functions such as redirecting, guiding, and focusing these waves, up to nonlinear all-optical routing. This opens the way to light control in a functionalized discrete space, i.e., discrete photonics.

  15. Optical Magnetometer Incorporating Photonic Crystals

    NASA Technical Reports Server (NTRS)

    Kulikov, Igor; Florescu, Lucia

    2007-01-01

    According to a proposal, photonic crystals would be used to greatly increase the sensitivities of optical magnetometers that are already regarded as ultrasensitive. The proposal applies, more specifically, to a state-of-the-art type of quantum coherent magnetometer that exploits the electromagnetically-induced-transparency (EIT) method for determining a small change in a magnetic field indirectly via measurement of the shift, induced by that change, in the hyperfine levels of resonant atoms exposed to the field.

  16. The Metagalactic Ionizing Background: A Crisis in UV Photon Production or Incorrect Galaxy Escape Fractions?

    NASA Astrophysics Data System (ADS)

    Shull, J. Michael; Moloney, Joshua; Danforth, Charles W.; Tilton, Evan M.

    2015-09-01

    Recent suggestions of a “photon underproduction crisis” have generated concern over the intensity and spectrum of ionizing photons in the metagalactic ultraviolet background (UVB). The balance of hydrogen photoionization and recombination determines the opacity of the low-redshift intergalactic medium (IGM). We calibrate the hydrogen photoionization rate ({{{Γ }}}{{H}}) by comparing Hubble Space Telescope spectroscopic surveys of the low-redshift column density distribution of H i absorbers and the observed (z\\lt 0.4) mean Lyα flux decrement, {D}A=(0.014){(1+z)}2.2, to new cosmological simulations. The distribution, f({N}{{H} {{I}}},z)\\equiv {d}2{N}/d({log}{N}{{H} {{I}}}){dz}, is consistent with an increased UVB that includes contributions from both quasars and galaxies. Our recommended fit, {{{Γ }}}{{H}}(z)=(4.6× {10}-14 {{{s}}}-1){(1+z)}4.4 for 0\\lt z\\lt 0.47, corresponds to unidirectional LyC photon flux {{{Φ }}}0≈ 5700 cm-2 s-1 at z = 0. This flux agrees with observed IGM metal ionization ratios (C iii/C iv and Si iii/Si iv) and suggests a 25%-30% contribution of Lyα absorbers to the cosmic baryon inventory. The primary uncertainties in the low-redshift UVB are the contribution from massive stars in galaxies and the LyC escape fraction ({f}{esc}), a highly directional quantity that is difficult to constrain statistically. We suggest that both quasars and low-mass starburst galaxies are important contributors to the ionizing UVB at z\\lt 2. Their additional ionizing flux would resolve any crisis in photon underproduction.

  17. Photonic sensing of arterial distension

    PubMed Central

    Ruh, Dominic; Subramanian, Sivaraman; Sherman, Stanislav; Ruhhammer, Johannes; Theodor, Michael; Dirk, Lebrecht; Foerster, Katharina; Heilmann, Claudia; Beyersdorf, Friedhelm; Zappe, Hans; Seifert, Andreas

    2016-01-01

    Most cardiovascular diseases, such as arteriosclerosis and hypertension, are directly linked to pathological changes in hemodynamics, i.e. the complex coupling of blood pressure, blood flow and arterial distension. To improve the current understanding of cardiovascular diseases and pave the way for novel cardiovascular diagnostics, innovative tools are required that measure pressure, flow, and distension waveforms with yet unattained spatiotemporal resolution. In this context, miniaturized implantable solutions for continuously measuring these parameters over the long-term are of particular interest. We present here an implantable photonic sensor system capable of sensing arterial wall movements of a few hundred microns in vivo with sub-micron resolution, a precision in the micrometer range and a temporal resolution of 10 kHz. The photonic measurement principle is based on transmission photoplethysmography with stretchable optoelectronic sensors applied directly to large systemic arteries. The presented photonic sensor system expands the toolbox of cardiovascular measurement techniques and makes these key vital parameters continuously accessible over the long-term. In the near term, this new approach offers a tool for clinical research, and as a perspective, a continuous long-term monitoring system that enables novel diagnostic methods in arteriosclerosis and hypertension research that follow the trend in quantifying cardiovascular diseases by measuring arterial stiffness and more generally analyzing pulse contours. PMID:27699095

  18. Nanomanipulation using near field photonics.

    PubMed

    Erickson, David; Serey, Xavier; Chen, Yih-Fan; Mandal, Sudeep

    2011-03-21

    In this article we review the use of near-field photonics for trapping, transport and handling of nanomaterials. While the advantages of traditional optical tweezing are well known at the microscale, direct application of these techniques to the handling of nanoscale materials has proven difficult due to unfavourable scaling of the fundamental physics. Recently a number of research groups have demonstrated how the evanescent fields surrounding photonic structures like photonic waveguides, optical resonators, and plasmonic nanoparticles can be used to greatly enhance optical forces. Here, we introduce some of the most common implementations of these techniques, focusing on those which have relevance to microfluidic or optofluidic applications. Since the field is still relatively nascent, we spend much of the article laying out the fundamental and practical advantages that near field optical manipulation offers over both traditional optical tweezing and other particle handling techniques. In addition we highlight three application areas where these techniques namely could be of interest to the lab-on-a-chip community, namely: single molecule analysis, nanoassembly, and optical chromatography.

  19. The Puerto Rico Photonics Institute

    NASA Astrophysics Data System (ADS)

    Friedman, Jonathan S.

    2014-07-01

    We have founded the Puerto Rico Photonics Institute (PRPI) in the Barceloneta, Puerto Rico campus of the Universidad Metropolitana. PRPI is established to provide opportunities in education, training and research and is unique in Puerto Rico. There are two initial focus areas of research and education: aerospace photonics and remote sensing. In particular, we will conduct studies and research and development in two particular fields: laser gyroscopes and similar technologies, and atmospheric remote sensing. PRPI has established local collaborations with the Arecibo Observatory and Honeywell Aerospace. Outside of Puerto Rico, PRPI collaborators include the University of Central Florida (CREOL), University of Arizona (OSC), University of Dayton (UD), Georgia Institute of Technology (GT), Scientific Solutions, Inc. (SSI), Atmospheric and Space Technology Research Associates (ASTRA), and the MIT Draper Laboratory. These organizations will help PRPI to: 1) establish its curriculum, provide research opportunities for PRPI students, 2) participate in faculty exchange programs, and 3) build its own research and development programs. PRPI will have educational and training programs for both Associate and Masters degrees, as well as a Certificate in Optics and Photonics for undergraduate science and engineering majors and professional engineers. PRPI is supported by UMET's parent institution, the Ana G. Mendez University System (SUAGM), the Puerto Rico Science, Technology and Research Trust (PRST), and the Puerto Rico Industrial Development Company (PRIDCO).

  20. Are there photons in fact?

    NASA Astrophysics Data System (ADS)

    Rashkovskiy, S. A.

    2015-09-01

    There are two opposing points of view on the nature of light: the first one manifests the wave-particle duality as a fundamental property of the nature; the second one claims that photons do not exist and the light is a continuous classical wave, while the so-called "quantum" properties of this field appear only as a result of its interaction with matter. In this paper we show that many quantum phenomena which are traditionally described by quantum electrodynamics can be described if light is considered within the limits of classical electrodynamics without quantization of radiation. These phenomena include the double-slit experiment, the photoelectric effect, the Compton effect, the Hanbury Brown and Twiss effect, the so-called multiphoton ionisation of atoms, etc. We show that this point of view allows also explaining the "wave-particle duality" of light in Wiener experiments with standing waves. We show that the Born rule for light can easily be derived from Fermi's golden rule as an approximation for low-intense light or for short exposure time. We show that the Heisenberg uncertainty principle for "photons" has a simple classical sense and cannot be considered as a fundamental limitation of accuracy of simultaneous measurements of position and momentum or time and energy. We conclude that the concept of a "photon" is superfluous in explanation of light-matter interactions.