Science.gov

Sample records for 10m semi anechoic

  1. Investigation on High Performance of 10m Semi Anechoic Chamber by using Open-Top Hollow Pyramidal Hybrid EM Wave Absorber

    NASA Astrophysics Data System (ADS)

    Kurihara, Hiroshi; Saito, Toshifumi; Suzuki, Yoshikazu; Nishikata, Atsuhiro; Hashimoto, Osamu

    The emission radiated from electric and electronic equipments is evaluated through OATS. Recently, it is not fully prepared the environment for OATS because of a variety of communication radiation sources (e.g., digital television broadcast and cellular phone station). Therefore, the EM anechoic chambers are becoming more and more important as EMI test site. On the other hand, the EM anechoic chambers are needed high performance in order to cut down EMI countermeasure cost and calculate the antenna factor. The objective of this paper is mainly to present the EM wave absorber design in order to obtain within ±2dB against the theoretical site attenuation values in the 10m semi anechoic chamber at 30MHz to 300MHz. We get the necessary reflectivity of EM wave absorber by the basic site attenuation equation. We design the open-top hollow pyramidal new hybrid EM wave absorber consisted of 180cm long dielectric loss foam and ferrite tiles. Then, we design the 10m semi anechoic chamber by using the ray-tracing simulation and construct it in the size of L24m×W15.2m×H11.2m. More over, we measure the site attenuation of the constructed 10m semi anechoic chamber by using the broadband calculable dipole antennas. As the result, we confirm the validity of the designed open-top hollow pyramidal new hybrid EM wave absorber.

  2. Anechoic chamber qualification at ultrasonic frequencies

    NASA Astrophysics Data System (ADS)

    Jenny, Trevor; Anderson, Brian

    2010-10-01

    Qualifying an anechoic chamber for frequencies that extend into the ultrasonic range is necessary for research work involving airborne ultrasonic sound. For example, an anechoic chamber allows for measurements of the direct sound radiated by an object without reflections from walls. The ANSI S12.55/ISO 3745 standard which covers anechoic chamber qualification does not extend into the ultrasonic frequency range, nor have others discussed this frequency range in the literature. An increasing number of technologies are employing ultrasound; hence the need to develop facilities to conduct basic research studies on airborne ultrasound. This presentation will discuss the challenges associated with chamber qualification and present the results for qualification of a chamber at Brigham Young University. [This work has been funded by the Los Alamos National Laboratory

  3. Almond test body. [for microwave anechoic chambers

    NASA Technical Reports Server (NTRS)

    Dominek, Allen K. (Inventor); Wood, Richard M. (Inventor); Gilreath, Melvin C. (Inventor)

    1989-01-01

    The invention is an almond shaped test body for use in measuring the performance characteristics of microwave anechoic chambers and for use as a support for components undergoing radar cross-section measurements. The novel aspect of this invention is its shape, which produces a large dynamic scattered field over large angular regions making the almond valuable for verifying the performance of microwave anechoic chambers. As a component mount, the almond exhibits a low return that does not perturb the measurement of the component and it simulates the backscatter characteristics of the component as if over an infinite ground plane.

  4. Tests of anechoic chamber for aeroacoustics investigations

    NASA Astrophysics Data System (ADS)

    Palchikovskiy, V. V.; Bersenev, Yu. V.; Makashov, S. Yu.; Belyaev, I. V.; Korin, I. A.; Sorokin, E. V.; Khramtsov, I. V.; Kustov, O. Yu.

    2016-10-01

    The paper presents the results of qualification tests in the new anechoic chamber of Perm National Research Polytechnic University (PNRPU) built in 2014-2015 and evaluation of the chamber quality in aeroacoustic experiments. It describes design features of the chamber and its sound-absorption lining. The qualification tests were carried out with tonal and broadband noise sources in the frequency range 100 Hz - 20 kHz for two different cases of the source arrangement. In every case, measurements were performed in three directions by traverse microphones. Qualification tests have determined that in the chamber there is a free acoustic field within radius of 2 m for tonal noise and 3 m for broadband noise. There was also evaluated acoustic quality of the chamber by measurements of the jet noise and vortex ring noise. The results of the experiments demonstrate that PNRPU anechoic chamber allows the aeroacoustic measurements to be performed to obtain quantitative results.

  5. Anechoic chamber in industrial plants. [construction materials and structural design

    NASA Technical Reports Server (NTRS)

    Halpert, E.; Juncu, O.; Lorian, R.; Marfievici, D.; Mararu, I.

    1974-01-01

    A light anechoic chamber for routine acoustical measurements in the machine building industry is reported. The outer housing of the chamber consists of modules cast in glass fiber reinforced polyester resin; the inner housing consists of pyramidal modules cut out of sound absorbing slates. The parameters of this anechoic chamber facilitate acoustical measurements according to ISO and CAEM recommendations.

  6. The Kevlar-walled anechoic wind tunnel

    NASA Astrophysics Data System (ADS)

    Devenport, William J.; Burdisso, Ricardo A.; Borgoltz, Aurelien; Ravetta, Patricio A.; Barone, Matthew F.; Brown, Kenneth A.; Morton, Michael A.

    2013-08-01

    The aerodynamic and acoustic performance of an anechoic wind tunnel test section with walls made from thin Kevlar cloth have been measured and analyzed. The Kevlar test section offers some advantages over a conventional free-jet arrangement. The cloth contains the bulk of the flow but permits the transmission of sound with little loss. The containment results in smaller far-field aerodynamic corrections meaning that larger models can be tested at higher Reynolds numbers. The containment also eliminates the need for a jet catcher and allows for a much longer test section. Model-generated noise is thus more easily separated from facility background using beamforming. Measurements and analysis of acoustic and aerodynamic corrections for a Kevlar-walled test section are presented and discussed, along with benchmark trailing edge noise measurements.

  7. Anechoic Chambers: Aerospace Applications. (Latest Citations from the Aerospace Database)

    NASA Technical Reports Server (NTRS)

    1996-01-01

    The bibliography contains citations concerning the design, development, performance, and applications of anechoic chambers in the aerospace industry. Anechoic chamber testing equipment, techniques for evaluation of aerodynamic noise, microwave and radio antennas, and other acoustic measurement devices are considered. Shock wave studies on aircraft models and components, electromagnetic measurements, jet flow studies, and antenna radiation pattern measurements for industrial and military aerospace equipment are discussed. (Contains 50-250 citations and includes a subject term index and title list.)

  8. Anechoic Chambers: Aerospace Applications. (Latest Citations from the Aerospace Database)

    NASA Technical Reports Server (NTRS)

    1995-01-01

    The bibliography contains citations concerning the design, development, performance, and applications of anechoic chambers in the aerospace industry. Anechoic chamber testing equipment, techniques for evaluation of aerodynamic noise, microwave and radio antennas, and other acoustic measurement devices are considered. Shock wave studies on aircraft models and components, electromagnetic measurements, jet flow studies, and antenna radiation pattern measurements for industrial and military aerospace equipment are discussed. (Contains 50-250 citations and includes a subject term index and title list.)

  9. Analysis of Anechoic Chamber Testing of the Hurricane Imaging Radiometer

    NASA Technical Reports Server (NTRS)

    Fenigstein, David; Ruf, Chris; James, Mark; Simmons, David; Miller, Timothy; Buckley, Courtney

    2010-01-01

    The Hurricane Imaging Radiometer System (HIRAD) is a new airborne passive microwave remote sensor developed to observe hurricanes. HIRAD incorporates synthetic thinned array radiometry technology, which use Fourier synthesis to reconstruct images from an array of correlated antenna elements. The HIRAD system response to a point emitter has been measured in an anechoic chamber. With this data, a Fourier inversion image reconstruction algorithm has been developed. Performance analysis of the apparatus is presented, along with an overview of the image reconstruction algorithm

  10. Design and Characterization of the UTIAS Anechoic Wind Tunnel

    NASA Astrophysics Data System (ADS)

    Chow, Derrick H. F.

    The anechoic open-jet wind tunnel facility at the University of Toronto Institute for Aerospace Studies was updated and characterized to meet the needs of current and future aeroacoustic experiments. The wind tunnel inlet was resurfaced and flow-conditioning screens were redesigned to improve the freestream turbulence intensity to below 0.4% in the test section. The circular nozzle was replaced with a square secondary contraction that increased the maximum test section velocity to 75 m/s and improved flow uniformity to over 99% across a usable cross-sectional area of 500 mm x 500 mm. Acoustic baffles were installed in front of the wind tunnel inlet and foam wedges were installed in the anechoic chamber. The overall background sound pressure levels in the chamber were improved by 8-18 db over the range of operational freestream velocities. The anechoic chamber cut-off frequency is 170 Hz and the reverberation time for a 60 dB sound power decay is 0.032 s.

  11. On the acoustic wedge design and simulation of anechoic chamber

    NASA Astrophysics Data System (ADS)

    Jiang, Changyong; Zhang, Shangyu; Huang, Lixi

    2016-10-01

    This study proposes an alternative to the classic wedge design for anechoic chambers, which is the uniform-then-gradient, flat-wall (UGFW) structure. The working mechanisms of the proposed structure and the traditional wedge are analyzed. It is found that their absorption patterns are different. The parameters of both structures are optimized for achieving minimum absorber depth, under the condition of absorbing 99% of normal incident sound energy. It is found that, the UGFW structure achieves a smaller total depth for the cut-off frequencies ranging from 100 Hz to 250 Hz. This paper also proposes a modification for the complex source image (CSI) model for the empirical simulation of anechoic chambers, originally proposed by Bonfiglio et al. [J. Acoust. Soc. Am. 134 (1), 285-291 (2013)]. The modified CSI model considers the non-locally reactive effect of absorbers at oblique incidence, and the improvement is verified by a full, finite-element simulation of a small chamber. With the modified CSI model, the performance of both decorations with the optimized parameters in a large chamber is simulated. The simulation results are analyzed and checked against the tolerance of 1.5 dB deviation from the inverse square law, stipulated in the ISO standard 3745(2003). In terms of the total decoration depth and anechoic chamber performance, the UGFW structure is better than the classic wedge design.

  12. Method for material characterization in a non-anechoic environment

    NASA Astrophysics Data System (ADS)

    Pometcu, L.; Sharaiha, A.; Benzerga, R.; Tamas, R. D.; Pouliguen, P.

    2016-04-01

    This paper presents a characterization method for extracting the reflection coefficient of materials and the real part of their permittivity. The characterization is performed in a real environment, as opposed to the classical measurement methods that require an anechoic chamber. In order to reduce the effects of the multipath propagation, a free space bistatic measurement was performed at different distances material-antennas in far field. By using a Teflon sample and a commercial absorbing material sample, measurements have been performed in order to validate the characterization technique.

  13. Processing of Prosthetic Heart Valve Sounds from Anechoic Tank Measurements

    SciTech Connect

    Candy, J V; Meyer, A W

    2001-03-20

    People with serious cardiac problems have had their life span extended with the development of the prosthetic heart valve. However, the valves operate continuously at approximately 39 million cycles per year and are therefore subject to structural failures either by faulty design or material fatigue. The development of a non-invasive technique using an acoustic contact microphone and sophisticated signal processing techniques has been proposed and demonstrated on limited data sets. In this paper we discuss an extension of the techniques to perform the heart valve tests in an anechoic like. Here the objective is to extract a ''pure'' sound or equivalently the acoustical vibration response of the prosthetic valves in a quiet environment. The goal is to demonstrate that there clearly exist differences between values which have a specific mechanical defect known as single leg separation (SLS) and non-defective valves known as intact (INT). We discuss the signal processing and results of anechoic acoustic measurements on 50 prosthetic valves in the tank. Finally, we show the results of the individual runs for each valve, point out any of the meaningful features that could be used to distinguish the SLS from INT and summarize the experiments.

  14. Construction of an anechoic chamber for aeroacoustic experiments and examination of its acoustic parameters

    NASA Astrophysics Data System (ADS)

    Kopiev, V. F.; Palchikovskiy, V. V.; Belyaev, I. V.; Bersenev, Yu. V.; Makashov, S. Yu.; Khramtsov, I. V.; Korin, I. A.; Sorokin, E. V.; Kustov, O. Yu.

    2017-01-01

    The acoustic parameters of a new anechoic chamber constructed at Perm National Research Polytechnic University (PNRPU) are presented. This chamber is designed to be used, among other things, for measuring noise from aerodynamic sources. Sound-absorbing wedges lining the walls of the chamber were studied in an interferometer with normal wave incidence. The results are compared to the characteristics of sound-absorbing wedges of existing anechoic facilities. Metrological examination of the acoustic parameters of the PNRPU anechoic chamber demonstrates that free field conditions are established in it, which will make it possible to conduct quantitative acoustic experiments.

  15. Numerical methodologies for optimizing and predicting the low frequency behavior of anechoic chambers.

    PubMed

    Bonfiglio, Paolo; Pompoli, Francesco

    2013-07-01

    This paper presents a description of the use of simplified numerical methodologies for the optimization of the low cut-off frequency of anechoic and hemi-anechoic chambers. The anechoic chamber is modeled as a cavity with proper surface impedance boundary conditions. First, the shape of the wedges is optimized by means of a minimization-based procedure of a finite element model of such elements in a "virtual" impedance tube for a plane wave field. An equivalent surface impedance of the wedges is determined from those data. An analytical procedure is then used to determine the complex reflection coefficient for spherical waves at oblique incidence. Finally, a complex image source approach is used to predict the sound field within the chamber. The methodology is applied to two anechoic chambers and the results are compared in terms of sound decay along fixed directions and surface pressure distributions.

  16. Subwavelength-Sized Narrow-Band Anechoic Waveguide Terminations

    NASA Astrophysics Data System (ADS)

    Santillán, Arturo; Ćrenlund, Emil; Bozhevolnyi, Sergey I.

    2016-11-01

    We propose and demonstrate the use of a pair of detuned acoustic resonators to efficiently absorb narrow-band sound waves in a terminated waveguide. The suggested configuration is relatively simple and advantageous for usage at low frequencies, since the dimensions of the resonators are very small compared to the wavelength. We present a theoretical description based on lumped parameters to calculate the absorption coefficient, which agrees very well with experimental data. The experimental results verify that the anechoic (reflection approximately -38 dB ) narrow-band (Δ f /f ˜0.1 ) termination with deeply subwavelength (<λ /10 ) sizes can be realized at a target frequency, suggesting thereby applications for noise control and sensing. As an illustration of possible applications for sound absorption in a room, we demonstrate by use of numerical simulations that a given axial resonant excitation in a room can be practically eliminated. Thus, a reduction of approximately 24 dB in the average acoustic energy is achieved in the room when using only four Helmholtz resonators. We also discuss various scenarios of noise control in rooms.

  17. Ultra-light duct for an anechoic wind tunnel

    NASA Technical Reports Server (NTRS)

    Lambourion, J.; Lewy, S.; Papirnyk, O.; Rahier, G.; Remandet, J.-N.

    1989-01-01

    A tunnel ultra-light (or TUL) is a duct composed of acoustically transparent cloth designed to transform an open-jet wind tunnel into a closed-jet wind tunnel. This concept is of interest (a priori) for anechoic wind tunnels because it improves the aerodynamic quality without hindering the measurement of sound in the far field. A full scale device designed for the 3 m diameter test section of CEPRA 19 was described. The apparatus installation did not develop any significant problems, and the mechanical support turned out to be excellent. Aerodynamic and acoustic tests are discussed. Certain imperfections in the installation as tested - instabilities above 25 m/s and acceptable cloth transmission up to 4kHz were revealed. The system as tested could eventually be used in certain applications, for example, in ground based transport. However, the concept of TUL must be developed further to arrive at a reliable mechanism for use in a large number of applications.

  18. Electromagnetic Radiation (EMR) coupling to complex systems : aperture coupling into canonical cavities in reverberant and anechoic environments and model validation.

    SciTech Connect

    Charley, Dawna R.; Higgins, Matthew B.

    2007-12-01

    Mode-stirred chamber and anechoic chamber measurements were made on two sets of canonical test objects (cylindrical and rectangular) with varying numbers of thin slot apertures. The shielding effectiveness was compared to determine the level of correction needed to compensate the mode-stirred data to levels commensurate with anechoic data from the same test object.

  19. Infrared scene projector system design description for installed infrared sensor testing in an anechoic chamber environment

    NASA Astrophysics Data System (ADS)

    Manzardo, Mark A.; Joyner, Thomas W.; Thiem, Keem B.

    1999-07-01

    A modular cost-effective Infrared Scene Projector (IRSP) system has been designed for testing infrared sensor(s) installed on host aerospace platform(s) in an anechoic chamber environment. The IRSP consists of the following major functional subsystems: Control Electronics Subsystem, Infrared Emitter Subsystem, Projection Optics Subsystem, Mounting Platform Subsystem and Non-Uniformity Correction Subsystem.

  20. A two dimensional finite difference time domain analysis of the quiet zone fields of an anechoic chamber

    NASA Technical Reports Server (NTRS)

    Ryan, Deirdre A.; Luebbers, Raymond J.; Nguyen, Truong X.; Kunz, Karl S.; Steich, David J.

    1992-01-01

    Prediction of anechoic chamber performance is a difficult problem. Electromagnetic anechoic chambers exist for a wide range of frequencies but are typically very large when measured in wavelengths. Three dimensional finite difference time domain (FDTD) modeling of anechoic chambers is possible with current computers but at frequencies lower than most chamber design frequencies. However, two dimensional FDTD (2D-FTD) modeling enables much greater detail at higher frequencies and offers significant insight into compact anechoic chamber design and performance. A major subsystem of an anechoic chamber for which computational electromagnetic analyses exist is the reflector. First, an analysis of the quiet zone fields of a low frequency anechoic chamber produced by a uniform source and a reflector in two dimensions using the FDTD method is presented. The 2D-FDTD results are compared with results from a three dimensional corrected physical optics calculation and show good agreement. Next, a directional source is substituted for the uniform radiator. Finally, a two dimensional anechoic chamber geometry, including absorbing materials, is considered, and the 2D-FDTD results for these geometries appear reasonable.

  1. A Large Hemi-Anechoic Enclosure for Community-Compatible Aeroacoustic Testing of Aircraft Propulsion Systems

    NASA Technical Reports Server (NTRS)

    Cooper, Beth A.

    1993-01-01

    A large hemi-anechoic (absorptive walls and acoustically hard floor) noise control enclosure has been erected around a complex of test stands at the NASA Lewis Research Center in Cleveland, Ohio. This new state-of-the-art Aeroacoustic Propulsion Laboratory (APL) provides an all-weather, semisecure test environment while limiting noise to acceptable levels in surrounding residential neighborhoods. The 39.6 m (130 ft) diameter geodesic dome structure houses the new Nozzle Aeroacoustic Test Rig (NATR), an ejector-powered M = 0.3 free jet facility for acoustic testing of supersonic aircraft exhaust nozzles and turbomachinery. A multi-axis, force-measuring Powered Lift Facility (PLF) stand for testing of Short Takeoff Vertical Landing (STOVL) vehicles is also located within the dome. The design of the Aeroacoustic Propulsion Laboratory efficiently accomodates the research functions of two separate test rigs, one of which (NATR) requires a specialized environment for taking acoustic measurements. Absorptive fiberglass wedge treatment on the interior surface of the dome provides a hemi-anechoic interior environment for obtaining the accurate acoustic measurements required to meet research program goals. The APL is the first known geodesic dome structure to incorporate transmission-loss properties as well as interior absorption into a free-standing, community-compatible, hemi-anechoic test facility.

  2. Demonstration of a 10-m Solar Sail System

    NASA Technical Reports Server (NTRS)

    Murphy, David M.; Macy, Brian D.; Gaspar, James L.

    2004-01-01

    The NASA In-Space Propulsion (ISP) program has been sponsoring system design development and hardware demonstration activities of solar sail technology over the past 16 months. Efforts to validate by test a moderate-scale (10-m) 1/4 symmetry ground demonstration sail system are nearly complete. Results of testing and analytical model validation of component and assembly functional, strength, stiffness, shape, and dynamic behavior are discussed.

  3. Microchannel anechoic corner for size-selective separation and medium exchange via traveling surface acoustic waves.

    PubMed

    Destgeer, Ghulam; Ha, Byung Hang; Park, Jinsoo; Jung, Jin Ho; Alazzam, Anas; Sung, Hyung Jin

    2015-05-05

    We demonstrate a miniaturized acoustofluidic device composed of a pair of slanted interdigitated transducers (SIDTs) and a polydimethylsiloxane microchannel for achieving size-selective separation and exchange of medium around polystyrene particles in a continuous, label-free, and contactless fashion. The SIDTs, deposited parallel to each other, produce tunable traveling surface acoustic waves (TSAWs) at desired locations, which, in turn, yield an anechoic corner inside the microchannel that is used to selectively deflect particles of choice from their streamlines. The TSAWs with frequency fR originating from the right SIDT and propagating left toward the microchannel normal to the fluid flow direction, laterally deflect larger particles with diameter d1 from the hydrodynamically focused sample fluid that carries other particles as well with diameters d2 and d3, such that d1 > d2 > d3. The deflected particles (d1) are pushed into the top-left corner of the microchannel. Downstream, the TSAWs with frequency fL, such that fL > fR, disseminating from the left SIDT, deflect the medium-sized particles (d2) rightward, leaving behind the larger particles (d1) unaffected in the top-left anechoic corner and the smaller particles (d3) in the middle of the microchannel, thereby achieving particle separation. A particle not present in the anechoic corner could be deflected rightward to realize twice the medium exchange. In this work, the three-way separation of polystyrene particles with diameters of 3, 4.2, and 5 μm and 3, 5, and 7 μm is achieved using two separate devices. Moreover, these devices are used to demonstrate multimedium exchange around polystyrene particles ∼5 μm and 7 μm in diameter.

  4. LLNL heart valve condition classification project anechoic testing results at the TRANSDEC evaluation facility

    SciTech Connect

    Candy, J V

    1999-10-31

    This report first briefly outlines the procedures and support/activation fixture developed at LLNL to perform the heart valve tests in an anechoic-like tank at the US Navy Transducer Evaluation Facility (TransDec) located in San Diego, CA. Next they discuss the basic experiments performed and the corresponding experimental plan employed to gather meaningful data systematically. The signal processing required to extract the desired information is briefly developed along with some of the data. Finally, they show the results of the individual runs for each valve, point out any of the meaningful features and summaries.

  5. Anechoic Chamber test of the Electromagnetic Measurement System ground test unit

    SciTech Connect

    Stevenson, L.E.; Scott, L.D.; Oakes, E.T.

    1987-04-10

    The Electromagnetic Measurement System (EMMS) will acquire data on electromagnetic (EM) environments at key weapon locations on various aircraft certified for nuclear weapons. The high-frequency ground unit of the EMMS consists of an instrumented B61 bomb case that will measure (with current probes) the localized current density resulting from an applied EM field. For this portion of the EMMS, the first system test was performed in the Anechoic Chamber Facility at Sandia National Laboratories, Albuquerque, New Mexico. The EMMS pod was subjected to EM radiation at microwave frequencies of 1, 3, and 10 GHz. At each frequency, the EMMS pod was rotated at many positions relative to the microwave source so that the individual current probes were exposed to a direct line-of-sight illumination. The variations between the measured and calculated electric fields for the current probes with direct illumination by the EM source are within a few db. The results obtained from the anechoic test were better than expected and verify that the high frequency ground portion of the EMMS will accurately measure the EM environments for which it was designed.

  6. Performance of the high speed anechoic wind tunnel at Lyon University

    NASA Technical Reports Server (NTRS)

    Sunyach, M.; Brunel, B.; Comte-Bellot, G.

    1986-01-01

    The characteristics of the feed duct, the wind tunnel, and the experiments run in the convergent-divergent anechoic wind tunnel at Lyon University are described. The wind tunnel was designed to eliminate noise from the entrance of air or from flow interactions with the tunnel walls so that noise caused by the flow-test structure interactions can be studied. The channel contains 1 x 1 x 0.2 m glass and metal foil baffles spaced 0.2 m apart. The flow is forced by a 350 kW fan in the primary circuit, and a 110 kW blower in the secondary circuit. The primary circuit features a factor of four throat reductions, followed by a 1.6 reduction before the test section. Upstream and downstream sensors permit monitoring of the anechoic effectiveness of the channel. Other sensors allow modeling of the flow structures in the tunnel. The tunnel was used to examine turbulent boundary layers in flows up to 140 m/sec, tubulence-excited vibrations in walls, and the effects of laminar and turbulent flows on the appearance and locations of noise sources.

  7. 10m/500 Mbps WDM visible light communication systems.

    PubMed

    Lin, Wen-Yi; Chen, Chia-Yi; Lu, Hai-Han; Chang, Ching-Hung; Lin, Ying-Pyng; Lin, Huang-Chang; Wu, Hsiao-Wen

    2012-04-23

    A wavelength-division-multiplexing (WDM) visible light communiction (VLC) system employing red and green laser pointer lasers (LPLs) with directly modulating data signals is proposed and experimentally demonstrated. With the assistance of preamplifier and adaptive filter at the receiving sites, low bit error rate (BER) at 10 m/500 Mbps operation is obtained for each wavelength. The use of preamplifier and adaptive filter offer significant improvements for free-space transmission performance. Improved performance of BER of <10(-9), as well as better and clear eye diagram were achieved in our proposed WDM VLC systems. LPL features create a new category of good performance with high-speed data rate, long transmission length (>5m), as well as easy handling and installation. This proposed WDM VLC system reveals a prominent one to present its advancement in simplicity and convenience to be installed.

  8. A microwave applicator for uniform irradiation by circularly polarized waves in an anechoic chamber.

    PubMed

    Chiang, W Y; Wu, M H; Wu, K L; Lin, M H; Teng, H H; Tsai, Y F; Ko, C C; Yang, E C; Jiang, J A; Barnett, L R; Chu, K R

    2014-08-01

    Microwave applicators are widely employed for materials heating in scientific research and industrial applications, such as food processing, wood drying, ceramic sintering, chemical synthesis, waste treatment, and insect control. For the majority of microwave applicators, materials are heated in the standing waves of a resonant cavity, which can be highly efficient in energy consumption, but often lacks the field uniformity and controllability required for a scientific study. Here, we report a microwave applicator for rapid heating of small samples by highly uniform irradiation. It features an anechoic chamber, a 24-GHz microwave source, and a linear-to-circular polarization converter. With a rather low energy efficiency, such an applicator functions mainly as a research tool. This paper discusses the significance of its special features and describes the structure, in situ diagnostic tools, calculated and measured field patterns, and a preliminary heating test of the overall system.

  9. Anechoic wind tunnel study of turbulence effects on wind turbine broadband noise

    NASA Technical Reports Server (NTRS)

    Loyd, B.; Harris, W. L.

    1995-01-01

    This paper describes recent results obtained at MIT on the experimental and theoretical modelling of aerodynamic broadband noise generated by a downwind rotor horizontal axis wind turbine. The aerodynamic broadband noise generated by the wind turbine rotor is attributed to the interaction of ingested turbulence with the rotor blades. The turbulence was generated in the MIT anechoic wind tunnel facility with the aid of biplanar grids of various sizes. The spectra and the intensity of the aerodynamic broadband noise have been studied as a function of parameters which characterize the turbulence and of wind turbine performance parameters. Specifically, the longitudinal integral scale of turbulence, the size scale of turbulence, the number of turbine blades, and free stream velocity were varied. Simultaneous measurements of acoustic and turbulence signals were made. The sound pressure level was found to vary directly with the integral scale of the ingested turbulence but not with its intensity level. A theoretical model based on unsteady aerodynamics is proposed.

  10. A microwave applicator for uniform irradiation by circularly polarized waves in an anechoic chamber

    NASA Astrophysics Data System (ADS)

    Chiang, W. Y.; Wu, M. H.; Wu, K. L.; Lin, M. H.; Teng, H. H.; Tsai, Y. F.; Ko, C. C.; Yang, E. C.; Jiang, J. A.; Barnett, L. R.; Chu, K. R.

    2014-08-01

    Microwave applicators are widely employed for materials heating in scientific research and industrial applications, such as food processing, wood drying, ceramic sintering, chemical synthesis, waste treatment, and insect control. For the majority of microwave applicators, materials are heated in the standing waves of a resonant cavity, which can be highly efficient in energy consumption, but often lacks the field uniformity and controllability required for a scientific study. Here, we report a microwave applicator for rapid heating of small samples by highly uniform irradiation. It features an anechoic chamber, a 24-GHz microwave source, and a linear-to-circular polarization converter. With a rather low energy efficiency, such an applicator functions mainly as a research tool. This paper discusses the significance of its special features and describes the structure, in situ diagnostic tools, calculated and measured field patterns, and a preliminary heating test of the overall system.

  11. ATS 6 EMI field measurements techniques and results. [anechoic chamber scale model testing

    NASA Technical Reports Server (NTRS)

    Afifi, M. S.; Keiser, B. E.

    1974-01-01

    At the present time 'Applications Technology Satellite (ATS)-6' is the world's largest communication satellite. It handles telecommunications in the frequency range of 40 - 30,000 MHz. Power levels on board the spacecraft range from -110 dBm to 52.5 dBw. Consequently considerable care was required in the design and test of this spacecraft, in order to provide assurances that the spacecraft would perform properly in its own RF environments. The testing was performed first by placing the earth viewing module (EVM) in a specially constructed 'small' anechoic chamber with an overhead parabolic reflector section, of 8' in diameter, instead of the 30' reflector of the full scale design. The near field analysis of this paper proves that this test configuration leads to a desirable overtest for the spacecraft. The test requirements, procedure and results are also explained.

  12. A microwave applicator for uniform irradiation by circularly polarized waves in an anechoic chamber

    SciTech Connect

    Chiang, W. Y.; Wu, M. H.; Wu, K. L.; Lin, M. H.; Teng, H. H.; Barnett, L. R.; Chu, K. R.; Tsai, Y. F.; Ko, C. C.; Yang, E. C.; Jiang, J. A.

    2014-08-15

    Microwave applicators are widely employed for materials heating in scientific research and industrial applications, such as food processing, wood drying, ceramic sintering, chemical synthesis, waste treatment, and insect control. For the majority of microwave applicators, materials are heated in the standing waves of a resonant cavity, which can be highly efficient in energy consumption, but often lacks the field uniformity and controllability required for a scientific study. Here, we report a microwave applicator for rapid heating of small samples by highly uniform irradiation. It features an anechoic chamber, a 24-GHz microwave source, and a linear-to-circular polarization converter. With a rather low energy efficiency, such an applicator functions mainly as a research tool. This paper discusses the significance of its special features and describes the structure, in situ diagnostic tools, calculated and measured field patterns, and a preliminary heating test of the overall system.

  13. The New Anechoic Shielded Chambers Designed for Space and Commercial Applications at LIT

    NASA Technical Reports Server (NTRS)

    da Silva, Benjamim; Galvao, M. C.; Pereira, Clovis Solano

    2008-01-01

    The main objective of this paper is to present the capabilities of the new anechoic shielded rooms designed for space and commercial applications as part of the Integration and Testing Laboratory (LIT, Laboratorio de Integracao e Testes) in Brazil. A new anechoic shielded room named CBA2 has been in full operation since March 2007 and a remodeled chamber CBA1 is planned to be ready by the end of 2008, replacing an old facility which was in operation for the last 18 years. The Brazilian Space Program started with very small and simple satellites and the old CBA1 chamber was conceived in 1987 to accomplish the EMI/EMC tests not requiring significant volumes. Since the very beginning this facility was also used by the private sector for other applications mainly due to the absorption of digital electronics in all kind of products. The intense use of this facility during the last years, operating three shifts a day, caused a normal degradation and imposed several limitations. Therefore, a new totally remodeled chamber was designed considering the state of the art in terms of absorbers and associated instrumentation. On the other hand the facility CBA2 was conceived, designed and implemented to test large satellites taking into account the advance of the technology in terms of RF frequencies, power level, testing methodologies and several other factors. A very interesting and unique aspect of this project was the partnership between the private sector and governmental institution. As a result, the total investment was shared between several companies and consequently a time-sharing use of the facility as well.

  14. Classification of heart valve sounds from experiments in an anechoic water tank

    SciTech Connect

    Axelrod, M C; Clark, G A; Scott, D

    1999-06-01

    In vivo studies in both sheep and humans were plagued by a number of problems including movement artifacts, biological noise, low signal-to-noise ratio (SNR), chest-wall reverberation, and limited bandwidth recordings as discussed by [1]. To overcome these problems it was decided to record heart valve sounds under controlled conditions deep in an anechoic water tank, free from reverberation noise. The main goal of this experiment was to obtain measurements of ''pure'' heart valve sounds free of the scattering effects of the body. Experiments were conducted at the Transdec facility in San Diego [2]. We used a high quality hydrophone together with a wide-band data acquisition system [2]. We recorded sounds from 100 repetitions of the opening-closing cycles on each of 50 different heart valves, including 21 SLS valves and 29 intact valves. The power spectrum of the opening and closing phases of each cycle were calculated and outlier spectra removed as described by Candy [2]. In this report, we discuss the results of our classification of the heart valve sound measurements. The goal of this classification task was to apply the fundamental classification algorithms developed for the clinical data in 1994 and 1996 to the measurements from the anechoic water tank. From the beginning of this project, LLNL's responsibility has been to process and classify the heart valve sounds. For this experiment, however, we processed both the opening sounds and closing sounds for comparison purposes. The results of this experiment show that the classifier did not perform well because of low signal-to-noise ratio and excessive variability in signal power from beat-to-beat for a given valve.

  15. Classification of heart valve sounds from experiments in an anechoic water tank

    SciTech Connect

    Axelrod, M C; Clark, G A; Scott, D

    1999-06-01

    In vivo studies in both sheep and humans were plagued by a number of problems including movement artifacts, biological noise, low signal-to-noise ratio (SNR), chest-wall reverberation, and limited bandwidth recordings as discussed by [1]. To overcome these problems it was decided to record heart valve sounds under controlled conditions deep in an anechoic water tank, free from reverberation noise, including surface reflections. Experiments were conducted in a deep water tank at the Transdec facility in San Diego, which satisfies these requirements. The Transdec measurements are free of reverberations, but not totally free of acoustic and electrical noise. We used a high quality hydrophone together with a wide-band data acquisition system [2]. We recorded sounds from 100 repetitions of the opening-closing cycles on each of 50 different heart valves, including 21 SLS valves and 29 intact valves. The power spectrum of the opening and closing phases of each cycle were calculated and outlier spectra removed as described by Candy [2]. In this report, we discuss the results of our classification of the heart valve sound measurements. The goal of this classification task was to apply the fundamental classification algorithms developed for the clinical data in 1994 and 1996 to the measurements from the anechoic water tank. From the beginning of this project, LLNL's responsibility has been to process and classify the heart valve opening sounds. For this experiment, however, we processed both the opening sounds and closing sounds for comparison purposes. The results of this experiment show that the classifier did not perform well. We believe this is because of low signal-to-noise ratio and excessive variability in signal power from beat-to-beat for a given valve.

  16. Supervised Self-Organizing Classification of Superresolution ISAR Images: An Anechoic Chamber Experiment

    NASA Astrophysics Data System (ADS)

    Radoi, Emanuel; Quinquis, André; Totir, Felix

    2006-12-01

    The problem of the automatic classification of superresolution ISAR images is addressed in the paper. We describe an anechoic chamber experiment involving ten-scale-reduced aircraft models. The radar images of these targets are reconstructed using MUSIC-2D (multiple signal classification) method coupled with two additional processing steps: phase unwrapping and symmetry enhancement. A feature vector is then proposed including Fourier descriptors and moment invariants, which are calculated from the target shape and the scattering center distribution extracted from each reconstructed image. The classification is finally performed by a new self-organizing neural network called SART (supervised ART), which is compared to two standard classifiers, MLP (multilayer perceptron) and fuzzy KNN ([InlineEquation not available: see fulltext.] nearest neighbors). While the classification accuracy is similar, SART is shown to outperform the two other classifiers in terms of training speed and classification speed, especially for large databases. It is also easier to use since it does not require any input parameter related to its structure.

  17. Design and analysis of a hemi-anechoic chamber at Michigan Technological University

    NASA Astrophysics Data System (ADS)

    Dreyer, Jason; Jangale, Ashish; Rao, Mohan D.

    2005-09-01

    A four-wheel chassis roll dynamometer test facility was installed on the campus of Michigan Technological University (MTU). The chassis dynamometer was enclosed in a soundproof hem-anechoic room in order to conduct noise radiation measurements on test vehicles. All surfaces of the room, except the floor and control room window, were acoustically treated with donated tetrahedral acoustic cones and panels. The acoustic absorption properties of these materials were characterized through reverberation chamber and impedance tube testing, and the effects of air gaps, cone orientation, and cone mounting materials were qualitatively evaluated. The design of the wall, ceiling, and door treatments of the chamber was based on the sound absorption properties of these materials, in addition to spatial constraints and cost considerations. The treated chamber acoustics were predicted based on the amount of acoustic material that could be applied to given chamber dimensions and would still preserve the functionality of the room. These predictions were validated through evaluation of the actual room treatment based on average reverberation time at 100-Hz third-octave band, free sound field characteristic 6-dB reduction in sound pressure level (SPL) per doubling in distance from source, noise reduction at the chamber boundaries, and background SPL Noise Criteria (NC) Rating.

  18. Anechoic chamber qualification: traverse method, inverse square law analysis method, and nature of test signal.

    PubMed

    Cunefare, Kenneth A; Biesel, Van B; Tran, John; Rye, Ryan; Graf, Aaron; Holdhusen, Mark; Albanese, Anne-Marie

    2003-02-01

    Qualification of anechoic chambers is intended to demonstrate that the chamber supports the intended free-field environment within some permissible tolerance bounds. Key qualification issues include the method used to obtain traverse data, the analysis method for the data, and the use of pure tone or broadband noise as the chamber excitation signal. This paper evaluates the relative merits of continuous versus discrete traverses, of fixed versus optimal reference analysis of the traverse data, and of the use of pure tone versus broadband signals. The current practice of using widely space discrete sampling along a traverse is shown to inadequately sample the complexity of the sound field extant with pure tone traverses, but is suitable for broadband traverses. Continuous traverses, with spatial resolution on the order of 15% of the wavelength at the frequency of interest, are shown to be necessary to fully resolve the spatial complexity of pure tone qualifications. The use of an optimal reference method for computing the deviations from inverse square law is shown to significantly improve the apparent performance of the chamber for pure tone qualifications. Finally, the use of broadband noise as the test signal, as compared to pure tone traverses over the same span, is demonstrated to be a marginal indicator of chamber performance.

  19. Analysis and testing of a bistatic radar cross section measurement capability for the AFIT anechoic chamber

    NASA Astrophysics Data System (ADS)

    McCool, Timothy D.

    1990-12-01

    This research effort examined the feasibility of performing bistatic radar cross section (RCS) measurements in the AFIT anechoic chamber. The capability was established to measure the bistatic RCS of a target versus frequency and versus target azimuth angle. In either case, one of three bistatic angles (angle between transmit and receive antennas) is available: 45, 90, and 135 degrees. Accurate bistatic RCS measurements were obtained using a CW radar and utilizing background subtraction, bistatic calibration, and software range gating. Simple targets were selected for validation purposes since their bistatic RCS could be predicted. These consisted of spheres and flat plates (square, triangle, and five sided). Several computer codes were utilized for system validation. Two codes based on the uniform theory of diffraction were used to predict the scattering from the flat plates. A program using a Mie series solution provided the exact scattering from the flat plates. A program using a Mie series solution provided the exact scattering for the spheres, which were used for both RCS predictions and system calibrations.

  20. Is the frequent sonographic anechoic area distally in metacarpophalangeal joints a sign of arthritis?

    PubMed

    Ten Cate, David Folkert; Luime, Jolanda Jacoba; Hazes, Johanna Maria Wilhelmina; Kleinrensink, Gerrit-Jan; Jacobs, Johannes Wilhelmus Gerardus

    2014-10-01

    In clinical practice, ultrasonography (US) often reveals, in the dorsal scan, a small anechoic area distally in both inflamed and clinically non-inflamed metacarpophalangeal joints. This "distal anechogenicity in the metacarpophalangeal joint" (DAEM) might thus be scored false positively as arthritis. We aimed to investigate whether the DAEM is a sign of arthritis. We evaluated the prevalence of DAEMs in 24 non-arthritic subjects. We then compared the dimensions of the DAEM in 10 non-arthritic subjects with a DAEM and 7 consecutive rheumatoid arthritis (RA) outpatients, using 2-D and 3-D ultrasound. Furthermore, we dissected two fresh-frozen postmortem hand specimens after US. A DAEM was observed in the metacarpophalangeal 2 (MCP2) joints of 54% of the 24 non-selected non-arthritic individuals; in none of those did the joint exhibit a power Doppler signal. A DAEM was observed in 86% of the 7 RA patients. Dimensions of DAEMs did not statistically significantly differ between these groups. At 3-D imaging and dissection, the DAEM was found to be an extension of the metacarpophalangeal joint capsule. In conclusion, DAEMs occur frequently and are not a sign of arthritis, but are distal joint recesses. This should be taken into account when using current sensitive ultrasonographic scoring systems grading arthritis.

  1. Estimation of Density of Localized States in Amorphous Se80Te20 and Se80Te10M10 (M = Cd, In, Sb) Alloys Using AC Conductivity Measurements

    NASA Astrophysics Data System (ADS)

    Chandel, N.; Mehta, N.; Kumar, A.

    2015-08-01

    The ac conductivity of amorphous Se80Te20 (a-Se80Te20) and amorphous Se80Te10M10 (a-Se80Te10M10) alloys has been measured as a function of temperature and frequency in a low-temperature regime. An analysis of the experimental data confirms that ac conductivity is reasonably well interpreted by the Austin-Mott model. The density of localized states was determined in the low-temperature region from 201 K to 280 K. Possible explanations of "metal-induced effects" on the conduction mechanism of a-Se80Te20 alloy are discussed.

  2. Simulation of flight-type engine fan noise in the NASA-Lewis 9 x 15 anechoic wind tunnel

    NASA Technical Reports Server (NTRS)

    Heidmann, M. F.; Dietrich, D. A.

    1976-01-01

    A major problem in the measurement of aircraft engine fan noise is the difficulty of simulating, in a ground-based facility, the noise that occurs during flight. Flight-type noise as contrasted to the usual ground-static test noise exhibits substantial reductions in both (1) the time unsteadiness of tone noise and (2) the mean level of tones calculated to be nonpropagating or cut-off. A model fan designed with cut-off of the fundamental tone was acoustically tested in the anechoic wind tunnel under both static and tunnel flow conditions. The properties that characterize flight-type noise were progressively simulated with increasing tunnel flow. The distinctly lobed directivity pattern of propagating rotor/stator interaction modes was also observed. The results imply that the excess noise attributed to the ingestion of the flow disturbances that prevail near most static test facilities was substantially reduced with tunnel flow. The anechoic wind tunnel appears to be a useful facility for applied research on aircraft engine fan noise under conditions of simulated flight.

  3. Effectiveness of an inlet flow turbulence control device to simulate flight noise fan in an anechoic chamber

    NASA Technical Reports Server (NTRS)

    Woodward, R. P.; Wazyniak, J. A.; Shaw, L. M.; Mackinnon, M. J.

    1977-01-01

    A hemispherical inlet flow control device was tested on a 50.8 cm. (20-inch) diameter fan stage in the NASA-Lewis anechoic chamber. The control device used honeycomb and wire mesh to reduce turbulence intensities entering the fan. Far field acoustic power level results show about a 5 db reduction in blade passing tone and about 10 dB reduction in multiple pure tone sound power at 90% design fan speed with the inlet device in place. Hot film cross probes were inserted in the inlet to obtain data for two components of the turbulence at 65 and 90% design fan speed. Without the flow control device, the axial intensities were below 1.0%, while the circumferential intensities were almost twice this value. The inflow control device significantly reduced the circumferential turbulence intensities and also reduced the axial length scale.

  4. Simulation of Flight-Type Engine Fan Noise in the NASA-Lewis 9X15 Anechoic Wind Tunnel

    NASA Technical Reports Server (NTRS)

    Heidmann, M. F.; Dietrich, D. A.

    1976-01-01

    Flight type noise as contrasted to the usual ground static test noise exhibits substantial reductions in the time unsteadiness of tone noise, and in the mean level of tones calculated to be nonpropagating or cut-off. A model fan designed with cuttoff of the fundamental tone was acoustically tested in the anechoic wind tunnel under both static and tunnel flow conditions. The properties that characterize flight type noise were progressively simulated with increasing tunnel flow. The distinctly lobed directivity pattern of propagating rotor/stator interaction modes was also observed. Excess noise attributed to the ingestion of the flow disturbances that prevail near most static test facilities is substantially reduced with tunnel flow.

  5. Optical Positions of ICRF Sources from CTIO 1.0M Data

    DTIC Science & Technology

    2015-01-01

    ABSTRACT As part of the USNO radio-optical reference frame link project, data were taken with the CTIO 1.0 m telescope in 2009. First position...ABSTRACT As part of the USNO radio-optical reference frame link project, data were taken with the CTIO 1.0 m telescope in 2009. First position...Yale 1.0 meter telescope and Y4K camera which were used for this study. TABLE 1. INSTRUMENT PROPERTIES aperture 1000 mm focal ratio f/10 Cass. filters

  6. Characterization of the spatial resolution of different high-frequency imaging systems using a novel anechoic-sphere phantom

    PubMed Central

    Filoux, Erwan; Mamou, Jonathan; Aristizábal, Orlando; Ketterling, Jeffrey A.

    2011-01-01

    The spatial resolution of high-frequency ultrasound (HFU, >20 MHz) imaging systems is usually determined using wires perpendicular to the beam. Recently, two tissue-mimicking phantoms (TMPs) were developed to estimate the three-dimensional (3D) resolution. Each of the TMPs consist of nine, 1 cm wide slabs of tissue-mimicking material containing randomly distributed anechoic spheres. All anechoic spheres in one slab have the same dimensions, and their diameter is increased from 0.1 mm in the first slab to 1.09 mm in the last. The scattering background for one set of slabs was fabricated using 3.5 µm glass beads, while those of the second set were 6.4 µm. The ability of a HFU system to detect these spheres against a speckle background provides a realistic estimation of its 3D spatial resolution. In the present study, these TMPs were used with HFU systems using single-element transducers, linear arrays and annular arrays. The TMPs were immersed in water and each slab was scanned using a VisualSonics™ Vevo 770 and Vevo 2100, and a custom HFU system based on a 5-element annular array. The annular array had a nominal center frequency of 40 MHz, a focal length of 12 mm, and a total aperture of 6 mm. A synthetic-focusing algorithm was used to form images with an increased depth-of-field. The penetration depth was increased by using a linear-chirp signal spanning 15 to 65 MHz over 4 µs. Results obtained with the custom system were compared to those of the Vevo systems (40 MHz probes RMV-704 and MS-550D) in terms of sphere detection, i.e., 3D spatial resolution, and contrast-to-noise ratio (CNR). Resulting B-mode images indicated that only the linear-array transducer failed to clearly resolve the 0.2 mm spheres, which showed that the 3D spatial resolution of the single-element and annular-array transducers was superior to that of the linear array. The single-element transducer could only detect these spheres over a narrow 1.5 mm depth-of-field, while the annular array

  7. Crack growth of 10M Ni-Mn-Ga material in cyclic mechanical loading

    NASA Astrophysics Data System (ADS)

    Aaltio, I.; Ge, Y.; Pulkkinen, H.; Sjöberg, A.; Söderberg, O.; Liu, X. W.; Hannula, S.-P.

    The 10M martensitic Ni-Mn-Ga single crystal materials are usually applied in the magneto-mechanical actuators. Therefore, it is important to know the possible effect of the long-term cyclic shape changes on their structure and behavior. This can be evaluated with the mechanical fatigue testing. In the present study, the single crystal 10M Ni-Mn-Ga samples of different compositions were applied to strain-controlled uniaxial mechanical cycling in the multivariant state at ambient temperature. The experiments revealed distinctive changes of the twin variant structure, especially in the mobile twin area, density of twin boundaries, and in the tendency for fatigue crack growth. Characterization of the crack surface showed that the cracks in the microscale grow in a step-wise manner on specific crystallographic planes, i.e, twin boundary planes, but that the macroscopic crack does not occur only along crystallographic directions.

  8. DISSOLUTION OF PLUTONIUM METAL IN 8-10 M NITRIC ACID

    SciTech Connect

    Rudisill, T.; Pierce, R.

    2012-02-21

    The H-Canyon facility will be used to dissolve Pu metal for subsequent purification and conversion to plutonium dioxide (PuO{sub 2}) using Phase II of HB-Line. To support the new mission, the development of a Pu metal dissolution flowsheet which utilizes concentrated (8-10 M) nitric acid (HNO{sub 3}) solutions containing potassium fluoride (KF) is required. Dissolution of Pu metal in concentrated HNO{sub 3} is desired to eliminate the need to adjust the solution acidity prior to purification by anion exchange. The preferred flowsheet would use 8-10 M HNO{sub 3}, 0.015-0.07 M KF, and 0.5-1.0 g/L Gd to dissolve the Pu up to 6.75 g/L. An alternate flowsheet would use 8-10 M HNO{sub 3}, 0.1-0.2 M KF, and 1-2 g/L B to dissolve the Pu. The targeted average Pu metal dissolution rate is 20 mg/min-cm{sup 2}, which is sufficient to dissolve a 'standard' 2250-g Pu metal button in 24 h. Plutonium metal dissolution rate measurements showed that if Gd is used as the nuclear poison, the optimum dissolution conditions occur in 10 M HNO{sub 3}, 0.04-0.05 M KF, and 0.5-1.0 g/L Gd at 112 to 116 C (boiling). These conditions will result in an estimated Pu metal dissolution rate of {approx}11-15 mg/min-cm{sup 2} and will result in dissolution times of 36-48 h for standard buttons. The recommended minimum and maximum KF concentrations are 0.03 M and 0.07 M, respectively. The maximum KF concentration is dictated by a potential room-temperature Pu-Gd-F precipitation issue at low Pu concentrations. The purpose of the experimental work described in this report was two-fold. Initially a series of screening experiments was performed to measure the dissolution rate of Pu metal as functions of the HNO{sub 3}, KF, and Gd or B concentrations. The objective of the screening tests was to propose optimized conditions for subsequent flowsheet demonstration tests. Based on the rate measurements, this study found that optimal dissolution conditions in solutions containing 0.5-1.0 g/L Gd occurred in 8-10

  9. LES Modeling of Lateral Dispersion in the Ocean on Scales of 10 m to 10 km

    DTIC Science & Technology

    2015-10-20

    Report 3. DATES COVERED (From - To) 01/07/2010 – 06/06/2015 4. TITLE AND SUBTITLE LES Modeling of Lateral Dispersion in the Ocean on Scales of 10...ocean on scales of 0.1-10 km that can be implemented in larger- scale ocean models. These parameterizations will incorporate the effects of local...Distribution approved for public release; distribution is unlimited. Final Report LES Modeling of Lateral Dispersion on Scales of 10 m to 10 km M.-Pascale

  10. Bioaerosol sampling by a personal rotating cup sampler CIP 10-M.

    PubMed

    Görner, Peter; Fabriès, Jean-François; Duquenne, Philippe; Witschger, Olivier; Wrobel, Richard

    2006-01-01

    High concentrations of bioaerosols containing bacterial, fungal and biotoxinic matter are encountered in many workplaces, e.g. solid waste treatment plants, waste water treatment plants and sewage networks. A personal bioaerosol sampler, the CIP 10-M (M-microbiologic), has been developed to measure worker exposure to airborne biological agents. This sampler is battery operated; it is light and easy to wear and offers full work shift autonomy. It can sample much higher concentrations than biological impactors and limits the mechanical stress on the microorganisms. Biological particles are collected in 2 ml of liquid medium inside a rotating cup fitted with radial vanes to maintain an air flow rate of 10 l min(-1) at a rotational speed of approximately 7,000 rpm. The rotating cup is made of sterilisable material. The sampled particles follow a helicoidal trajectory as they are pushed to the surface of the liquid by centrifugal force, which creates a thin vertical liquid layer. Sterile water or another collecting liquid can be used. Three particle size selectors allow health-related aerosol fractions to be sampled according to international conventions. The sampled microbiological particles can be easily recovered for counting, incubation or further biochemical analysis, e.g., for airborne endotoxins. Its physical sampling efficiency was laboratory tested and field trials were carried out in industrial waste management conditions. The results indicate satisfactory collection efficiency, whilst experimental application has demonstrated the usefulness of the CIP 10-M personal sampler for individual bioaerosol exposure monitoring.

  11. DISSOLUTION OF PLUTONIUM METAL IN 8-10 M NITRIC ACID

    SciTech Connect

    Rudisill, T. S.; Pierce, R. A.

    2012-07-02

    The H-Canyon facility will be used to dissolve Pu metal for subsequent purification and conversion to plutonium dioxide (PuO{sub 2}) using Phase II of HB-Line. To support the new mission, the development of a Pu metal dissolution flowsheet which utilizes concentrated (8-10 M) nitric acid (HNO{sub 3}) solutions containing potassium fluoride (KF) is required. Dissolution of Pu metal in concentrated HNO{sub 3} is desired to eliminate the need to adjust the solution acidity prior to purification by anion exchange. The preferred flowsheet would use 8-10 M HNO{sub 3}, 0.015-0.07 M KF, and 0.5-1.0 g/L Gd to dissolve the Pu up to 6.75 g/L. An alternate flowsheet would use 8-10 M HNO{sub 3}, 0.05-0.2 M KF, and 1-2 g/L B to dissolve the Pu. The targeted average Pu metal dissolution rate is 20 mg/min-cm{sup 2}, which is sufficient to dissolve a “standard” 2250-g Pu metal button in 24 h. Plutonium metal dissolution rate measurements showed that if Gd is used as the nuclear poison, the optimum dissolution conditions occur in 10 M HNO{sub 3}, 0.04-0.05 M KF, and 0.5-1.0 g/L Gd at 112 to 116 °C (boiling). These conditions will result in an estimated Pu metal dissolution rate of ~11-15 mg/min-cm{sup 2} and will result in dissolution times of 36-48 h for standard buttons. The recommended minimum and maximum KF concentrations are 0.03 M and 0.07 M, respectively. The data also indicate that lower KF concentrations would yield dissolution rates for B comparable to those observed with Gd at the same HNO{sub 3} concentration and dissolution temperature. To confirm that the optimal conditions identified by the dissolution rate measurements can be used to dissolve Pu metal up to 6.75 g/L in the presence of representative concentrations of Fe and Gd or B, a series of experiments was performed to demonstrate the flowsheets. In three of the five experiments, the offgas generation rate during the dissolution was measured and samples were analyzed for hydrogen gas (H{sub 2}). The use of

  12. Deterministic separation of cancer cells from blood at 10 mL/min

    NASA Astrophysics Data System (ADS)

    Loutherback, Kevin; D'Silva, Joseph; Liu, Liyu; Wu, Amy; Austin, Robert H.; Sturm, James C.

    2012-12-01

    Circulating tumor cells (CTCs) and circulating clusters of cancer and stromal cells have been identified in the blood of patients with malignant cancer and can be used as a diagnostic for disease severity, assess the efficacy of different treatment strategies and possibly determine the eventual location of metastatic invasions for possible treatment. There is thus a critical need to isolate, propagate and characterize viable CTCs and clusters of cancer cells with their associated stroma cells. Here, we present a microfluidic device for mL/min flow rate, continuous-flow capture of viable CTCs from blood using deterministic lateral displacement (DLD) arrays. We show here that a DLD array device can isolate CTCs from blood with capture efficiency greater than 85% CTCs at volumetric flow rates of up to 10 mL/min with no effect on cell viability.

  13. Innovative Structural Design Features for a 10 m Solar Sail Demonstrator

    NASA Technical Reports Server (NTRS)

    Laue, G.; Moore, J.; Clayton, W.

    2004-01-01

    The successful development of sail architectures will require careful attention to a number of key issues including but not limited to material strength issues, stress conditions for the membrane, load interactions between membrane and structure, and membrane material planarity. Along with the inherent challenges of fabricating and handling very large membrane structures these issues will pose real challenges for the near-term development of practical sail technologies. SRS has developed innovative technologies that deal directly with the challenges of developing very large sail membranes. Some of these technologies include edge reinforcements and innovative reinforcement attachment techniques, production of flight durable sail materials of less than 2.5 micron thicknesses and large scale fabrication techniques. SRS has employed these technologies in several large 10 m demonstrators that have been delivered to LaRC for solar vacuum testing. Details of the design of this system will be discussed.

  14. Constraining the Bulk Density of 10m-Class Near-Earth Asteroid 2012 LA

    NASA Astrophysics Data System (ADS)

    Mommert, Michael; Hora, Joseph; Farnocchia, Davide; Trilling, David; Chesley, Steve; Harris, Alan; Mueller, Migo; Smith, Howard

    2016-08-01

    The physical properties of near-Earth asteroids (NEAs) provide important hints on their origin, as well as their past physical and orbital evolution. Recent observations seem to indicate that small asteroids are different than expected: instead of being monolithic bodies, some of them instead resemble loose conglomerates of smaller rocks, so called 'rubble piles'. This is surprising, since self-gravitation is practically absent in these bodies. Hence, bulk density measurements of small asteroids, from which their internal structure can be estimated, provide unique constraints on asteroid physical models, as well as models for asteroid evolution. We propose Spitzer Space Telescope observations of 10 m-sized NEA 2012 LA, which will allow us to constrain the diameter, albedo, bulk density, macroporosity, and mass of this object. We require 30 hrs of Spitzer time to detect our target with a minimum SNR of 3 in CH2. In order to interpret our observational results, we will use the same analysis technique that we used in our successful observations and analyses of tiny asteroids 2011 MD and 2009 BD. Our science goal, which is the derivation of the target's bulk density and its internal structure, can only be met with Spitzer. Our observations will produce only the third comprehensive physical characterization of an asteroid in the 10m size range (all of which have been carried out by our team, using Spitzer). Knowledge of the physical properties of small NEAs, some of which pose an impact threat to the Earth, is of importance for understanding their evolution and estimating the potential of destruction in case of an impact, as well as for potential manned missions to NEAs for either research or potential commercial uses.

  15. An Examination of Residual Wind Fluctuations Observed at 10 m over Flat Terrain.

    NASA Astrophysics Data System (ADS)

    Leahey, D. M.; Hansen, M. C.; Schroeder, M. B.

    1996-01-01

    This study investigates the behavior of wind fluctuations observed at the 10-m level over a flat terrain site located some 100 km east of the Rocky Mountains. The purposes were to assess residual fluctuations in order to ascertain effects attributable to the nonhomogenous, nonstationary character of turbulence and to evaluate influences of gravity waves. Residual wind fluctuations were defined for purposes of this study as the differences between observed half-hourly average standard deviations of wind fluctuations (v, u, w) and those that are expected to occur in association with simultaneous wind speeds and static stabilities. These latter fluctuations were estimated from equations developed by Leahey, Hansen, and Schroeder (LHS).Results of the analyses showed, as expected, that residual distributions for nonwesterly wind conditions were nearly Gaussian. Standard deviations for residuals of horizontal fluctuations, attributable to the nonhomogenous, nonstationary nature of turbulence, were 0.165 and 0.210 m s1 for stable and unstable situations, respectively. For residuals associated with vertical fluctuations they were, respectively, 0.065 and 0.075 m s1.Residuals for horizontal and vertical wind fluctuations observed when winds were from the mountains showed a greater tendency for the positive bias associated with gravity waves. This tendency was most evident under unstable conditions when gravity wave influences on horizontal fluctuations were apparent about 25% of the time. These influences are explained as being associated with mountain lee waves occurring at the planetary boundary layer's capping inversion. They are evidenced at the 10-m level because atmospheric mixing processes occurring in thermally unstable atmospheric situations bring momentum generated from these waves downward to the ground.Nonstationary and nonhomogenous atmospheric turbulence effects result in wind fluctuations whose half-hourly average standard deviations differ from those

  16. Size-Frequency Distribution of Boulders ≥ 10 m on Comet 103P/Hartley 2

    NASA Astrophysics Data System (ADS)

    Pajola, M.; Lucchetti, A.; A'Hearn, M. F.; Bertini, I.; Marzari, F.; La Forgia, F.; Lazzarin, M.; Naletto, G.; Barbieri, C.

    2015-12-01

    We present the first size-frequency distribution of boulders ≥ 10 m identified on comet 103P/Hartley 2, computed from the images taken by the Deep Impact/High Resolution Imager - Visible CCD camera on 4 November 2010. We derived the size-frequency distribution of the illuminated side of the comet (˜ 50%), as well as identified the power-law indexes characterizing the two lobes of 103P. 332 boulders larger than 10 m were identified on the imaged surface of the comet, with a global number density of nearly 140/km2 and a cumulative size-frequency distribution represented by a power-law with index of -2.7 ± 0.2. The two lobes of 103P show close indexes, i.e. -2.7 ± 0.2 for the bigger lobe (L1) and -2.6 +0.2/-0.5 for the smaller one (L2). Both the similar power-law indexes and the similar maximum boulder sizes derived for the two lobes point towards a similar fracturing/disintegration phenomena of the boulders as well as similar lifting processes that may occur in L1 and L2. Nonetheless, the significative difference in the number of boulders per km2 between the two lobes suggests that the more diffuse H2O sublimation on the bigger lobe produce twice the boulders per km2 with respect to those produced on the small lobe (primary activity CO2 driven). If we compare the boulder distribution of the hyperactive 103P comet with similar studies performed on 67P (67P/Churyumov-Gerasimenko, i.e. the comet studied by Rosetta spacecraft), we derive that 103P shows a lower global power-law index (-2.7 vs -3.6). The size-frequency boulder trend of 103P is somehow closer to the -2.2 value measured on the neck region of 67P, i.e. the most active region of the northern hemisphere of 67P; nevertheless the hyperactivity of 103P works in a very different way than the normal activity of 67P in the neck/Hapi area. In addition to the global differences between the two comets' activities, the absence of cliffs and walls on 103P show a completely different surface geomorphology between

  17. Size-frequency distribution of boulders ≥10 m on comet 103P/Hartley 2

    NASA Astrophysics Data System (ADS)

    Pajola, Maurizio; Lucchetti, Alice; Bertini, Ivano; Marzari, Francesco; A'Hearn, Michael F.; La Forgia, Fiorangela; Lazzarin, Monica; Naletto, Giampiero; Barbieri, Cesare

    2016-01-01

    Aims: We derive the size-frequency distribution of boulders on comet 103P/Hartley 2, which are computed from the images taken by the Deep Impact/HRI-V imaging system. We indicate the possible physical processes that lead to these boulder size distributions. Methods: We used images acquired by the High Resolution Imager-Visible CCD camera on 4 November 2010. Boulders ≥10 m were identified and manually extracted from the datasets with the software ArcGIS. We derived the global size-frequency distribution of the illuminated side of the comet (~50%) and identified the power-law indexes characterizing the two lobes of 103P. The three-pixel sampling detection, together with the shadowing of the surface, enables unequivocally detection of boulders scattered all over the illuminated surface. Results: We identify 332 boulders ≥10 m on the imaged surface of the comet, with a global number density of nearly 140/km2 and a cumulative size-frequency distribution represented by a power law with index of -2.7 ± 0.2. The two lobes of 103P show similar indexes, i.e., -2.7 ± 0.2 for the bigger lobe (called L1) and -2.6+ 0.2/-0.5 for the smaller lobe (called L2). The similar power-law indexes and similar maximum boulder sizes derived for the two lobes both point toward a similar fracturing/disintegration phenomena of the boulders as well as similar lifting processes that may occur in L1 and L2. The difference in the number of boulders per km2 between L1 and L2 suggests that the more diffuse H2O sublimation on L1 produce twice the boulders per km2 with respect to those produced on L2 (primary activity CO2 driven). The 103P comet has a lower global power-law index (-2.7 vs. -3.6) with respect to 67P. The global differences between the two comets' activities, coupled with a completely different surface geomorphology, make 103P hardly comparable to 67P. A shape distribution analysis of boulders ≥30 m performed on 103P suggests that the cometary boulders show more elongated shapes

  18. A high-precision angle encoder for a 10-m submillimeter antenna

    NASA Astrophysics Data System (ADS)

    Ukita, Nobuharu; Ezawa, Hajime; Mimura, Hisashi; Suganuma, Akira; Kitazawa, Kanji; Masuda, Tadashi; Kawaguchi, Noboru; Sugiyama, Ryuichi; Miyawaki, Keizou

    2001-03-01

    We report measurements of angle error characteristics of new high-precision multi-speed resolvers developed for a 10-m submillimeter telescope of Nobeyama Radio Observatory. We have found the resolvers have an accuracy of 0.03" rms and 0.26" peak-to-peak, which is well below the error budget assigned to the angle encoder in the LMSA/ALMA project (0.15 - 0.2"). The error pattern in the raw readout had simple characteristics and was only composed of a few Fourier components which are associated with the number of winding poles and core slot number of stator. The 4" peak-to-peak error in the raw readout is reduced to less than 1/15 by the PROM correction. We have also found that shaft misalignment causes only small changes of error pattern (0.08" error per 0.10 mm shaft misalignment), which enables us to install the resolver simply by the fitting. The temperature dependence of error pattern also seems to be small enough for the operation temperature range specified in the project.

  19. High Resolution Imaging of Satellites with Ground-Based 10-m Astronomical Telescopes

    SciTech Connect

    Marois, C

    2007-01-04

    High resolution imaging of artificial satellites can play an important role in current and future space endeavors. One such use is acquiring detailed images that can be used to identify or confirm damage and aid repair plans. It is shown that a 10-m astronomical telescope equipped with an adaptive optics system (AO) to correct for atmospheric turbulence using a natural guide star can acquire high resolution images of satellites in low-orbits using a fast shutter and a near-infrared camera even if the telescope is not capable of tracking satellites. With the telescope pointing towards the satellite projected orbit and less than 30 arcsec away from a guide star, multiple images of the satellite are acquired on the detector using the fast shutter. Images can then be shifted and coadded by post processing to increase the satellite signal to noise ratio. Using the Keck telescope typical Strehl ratio and anisoplanatism angle as well as a simple diffusion/reflection model for a satellite 400 km away observed near Zenith at sunset or sunrise, it is expected that such system will produced > 10{sigma} K-band images at a resolution of 10 cm inside a 60 arcsec diameter field of view. If implemented, such camera could deliver the highest resolution satellite images ever acquired from the ground.

  20. Invited review article: A 10 mK scanning probe microscopy facility.

    PubMed

    Song, Young Jae; Otte, Alexander F; Shvarts, Vladimir; Zhao, Zuyu; Kuk, Young; Blankenship, Steven R; Band, Alan; Hess, Frank M; Stroscio, Joseph A

    2010-12-01

    We describe the design, development and performance of a scanning probe microscopy (SPM) facility operating at a base temperature of 10 mK in magnetic fields up to 15 T. The microscope is cooled by a custom designed, fully ultra-high vacuum (UHV) compatible dilution refrigerator (DR) and is capable of in situ tip and sample exchange. Subpicometer stability at the tip-sample junction is achieved through three independent vibration isolation stages and careful design of the dilution refrigerator. The system can be connected to, or disconnected from, a network of interconnected auxiliary UHV chambers, which include growth chambers for metal and semiconductor samples, a field-ion microscope for tip characterization, and a fully independent additional quick access low temperature scanning tunneling microscope (STM) and atomic force microscope (AFM) system. To characterize the system, we present the cooling performance of the DR, vibrational, tunneling current, and tip-sample displacement noise measurements. In addition, we show the spectral resolution capabilities with tunneling spectroscopy results obtained on an epitaxial graphene sample resolving the quantum Landau levels in a magnetic field, including the sublevels corresponding to the lifting of the electron spin and valley degeneracies.

  1. Deformation twinning in Ni–Mn–Ga micropillars with 10M martensite

    PubMed Central

    Reinhold, M.; Kiener, D.; Knowlton, W. B.; Dehm, G.; Müllner, P.

    2009-01-01

    The maximum actuation frequency of magnetic shape-memory alloys (MSMAs) significantly increases with decreasing size of the transducer making MSMAs interesting candidates for small scale actuator applications. To study the mechanical properties of Ni–Mn–Ga single crystals on small length scales, two single-domain micropillars with dimensions of 10×15×30 μm3 were fabricated from a Ni–Mn–Ga monocrystal using dual beam focused ion beam machining. The pillars were oriented such that the crystallographic c direction was perpendicular to the loading direction. The pillars were compressed to maximum stresses of 350 and 50 MPa, respectively. Atomic force microscopy and magnetic force microscopy were performed prior to fabrication of the pillars and following the deformation experiments. Both micropillars were deformed by twinning as evidenced by the stress-strain curve. For one pillar, a permanent deformation of 3.6% was observed and ac twins (10M martensite) were identified after unloading. For the other pillar, only 0.7% remained upon unloading. No twins were found in this pillar after unloading. The recovery of deformation is discussed in the light of pseudoelastic twinning and twin-substrate interaction. The twinning stress was higher than in similar macroscopic material. However, further studies are needed to substantiate a size effect. PMID:19859577

  2. First Resolved Images of a Spacecraft in Geostationary Orbit with the Keck-II 10 m Telescope

    DTIC Science & Technology

    2010-09-01

    2009, with the adaptive optics on the largest telescope on the planet, the 10 m Keck-II on the 14000 foot summit of Mauna Kea . 1. Observations As...part of an engineering run at the Keck-II 10 m telescope on Mauna Kea , several adaptive optics images were obtained of geostationary satellite GE-23, a...largest telescope on the planet, the 10 m Keck-II on the 14000 foot summit of Mauna Kea . 15. SUBJECT TERMS 16. SECURITY CLASSIFICATION OF: 17

  3. Thermal and Wind Effects on the Azimuth Axis Tilt of the ASTE 10-m Antenna

    NASA Astrophysics Data System (ADS)

    Ukita, Nobuharu; Ezawa, Hajime; Ikenoue, Bungo; Saito, Masao

    2007-10-01

    The azimuth axis tilt of the ASTE 10-m antenna induced by thermal and wind loadings was investigated with a dual-axis inclinometer on the azimuth axis, along with thermometers on the pedestal and yoke structures and an ultrasonic anemometer on a nearby weather station. The dependences of the inclinometer zero-point offsets against temperature of the device, temperature gradients in the pedestal and yoke structure were obtained for the measurements over 11 months during the antenna being parked at its home position (azimuth angles = ?180 degrees, an elevation angle = 60 degrees) under wind velocities < 8 m s-1. The temperature dependences of the zero-point offsets were found to be 1.24 and -0.46 arcseconds/degree, and were close to those obtained with an independent method. The azimuth axis tilts due to the temperature difference between the two opposite sides of pedestal walls were found to be about 1.1 and 1.7 arcseconds/degree, and consistent with 1.5 arcseconds/degree estimated with a simple model. The residual axis tilt of the whole samples after removal of the temperature dependences shows dependence against overturning moment estimated from the wind data. The stiffness of the antenna structures between the yoke base section and the ground was estimated to be 5.3 and 3.4 GNm/rad using the observed tilts in two directions; and were smaller than 6.0 GNm/rad from a mechanical model prediction. Based on these field experiments, we discuss the improvements and limitations of pointing performance with the inclinometer metrology system.

  4. Correspondence - Characterization of the effective performance of a high-frequency annular-array-based imaging system using anechoic-pipe phantoms.

    PubMed

    Filoux, Erwan; Mamou, Jonathan; Moran, Carmel M; Pye, Stephen D; Ketterling, Jeffrey A

    2012-12-01

    A resolution integral (RI) method based on anechoic- pipe, tissue-mimicking phantoms was used to compare the detection capabilities of high-frequency imaging systems based on a single-element transducer, a state-of-the-art 256-element linear array, or a 5-element annular array. All transducers had a central frequency of 40 MHz with similar conventionally measured axial and lateral resolutions (about 50 and 85 μm, respectively). Using the RI metric, the annular array achieved the highest performance (RI = 60), followed by the linear array (RI = 47), and the single-element transducer (RI = 24). Results showed that the RI metric could be used to efficiently quantify the effective transducer performance and compare the image quality of different systems.

  5. A computer simulation for evaluating the array performance of the 10-m/phi/ 5-element super-synthesis telescope

    NASA Astrophysics Data System (ADS)

    Morita, K.-I.; Ishiguro, M.

    1980-03-01

    The array performance in several successive configurations was examined for the 10-m(phi) 5-element super-synthesis telescope. The number of (u, v) samples was used as a criterion of optimum (u, v) coverages. The optimum solution for a given declination was obtained by a random trial method. The performance was evaluated by computer simulation using model brightness distributions.

  6. Comparisons of Monthly Mean 10 M Wind Speeds from Satellites and NWP Products Over the Global Ocean

    DTIC Science & Technology

    2009-10-09

    Resolution QSCAT SSM/I NOGAPS ERA-40 NCEP Sea Winds instrument on the Quick Scatterometer Special Sensor Microwave/Imager Navy Operational...measurements with 25-point smoothing as described earlier. [25] Within the latitudes spanning the Arctic and Antarctic , no ice mask is applied in order to...ET AL.: 10 M WINDS OVER THE GLOBAL OCEAN D16109 egies that blend two or more of these products to produce improved forcing fields. [53

  7. 17 CFR 249.510 - Form 10-M, consent to service of process by a nonresident general partner of a broker-dealer firm.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 17 Commodity and Securities Exchanges 3 2011-04-01 2011-04-01 false Form 10-M, consent to service... ACT OF 1934 Forms for Statements Made in Connection With Exempt Tender Offers § 249.510 Form 10-M... Note: For Federal Register citations affecting Form 10-M, see the List of CFR Sections Affected,...

  8. Structures and Stabilities of the Metal Doped Gold Nano-Clusters: M@Au10 (M = W, Mo, Ru, Co).

    PubMed

    Hossain, Delwar; Pittman, Charles U; Gwaltney, Steven R

    2014-01-01

    The structures and stabilities of a series of endohedral gold clusters containing ten gold atoms M@Au10 (M = W, Mo, Ru, Co) have been determined using density functional theory. The gradient-corrected functional BP86, the Tao-Perdew-Staroverov-Scuseria TPSS meta-GGA functional, and the hybrid density functionals B3LYP and PBE1PBE were employed to calculate the structures, binding energies, adiabatic ionization potentials, and adiabatic electron affinities for these clusters. The LanL2DZ effective core potentials and the corresponding valence basis sets were employed. The M@Au10 (M = W, Mo, Ru, Co) clusters have higher binding energies than an empty Au10 cluster. In addition, the large HOMO-LUMO gaps suggest that the M@Au10 (M = W, Mo, Ru, Co) clusters are all likely to be stable chemically. The ionization potentials and electron affinities for these clusters are very high, and the W@Au10 and Mo@Au10 clusters have electron affinities similar to the super-halogen Al13.

  9. Structures and Stabilities of the Metal Doped Gold Nano-Clusters: M@Au10 (M = W, Mo, Ru, Co)

    PubMed Central

    Hossain, Delwar; Pittman, Charles U.; Gwaltney, Steven R.

    2014-01-01

    The structures and stabilities of a series of endohedral gold clusters containing ten gold atoms M@Au10 (M = W, Mo, Ru, Co) have been determined using density functional theory. The gradient-corrected functional BP86, the Tao-Perdew-Staroverov-Scuseria TPSS meta-GGA functional, and the hybrid density functionals B3LYP and PBE1PBE were employed to calculate the structures, binding energies, adiabatic ionization potentials, and adiabatic electron affinities for these clusters. The LanL2DZ effective core potentials and the corresponding valence basis sets were employed. The M@Au10 (M = W, Mo, Ru, Co) clusters have higher binding energies than an empty Au10 cluster. In addition, the large HOMO–LUMO gaps suggest that the M@Au10 (M = W, Mo, Ru, Co) clusters are all likely to be stable chemically. The ionization potentials and electron affinities for these clusters are very high, and the W@Au10 and Mo@Au10 clusters have electron affinities similar to the super-halogen Al13. PMID:24611036

  10. Identification of source velocities on 3D structures in non-anechoic environments: Theoretical background and experimental validation of the inverse patch transfer functions method

    NASA Astrophysics Data System (ADS)

    Aucejo, M.; Totaro, N.; Guyader, J.-L.

    2010-08-01

    In noise control, identification of the source velocity field remains a major problem open to investigation. Consequently, methods such as nearfield acoustical holography (NAH), principal source projection, the inverse frequency response function and hybrid NAH have been developed. However, these methods require free field conditions that are often difficult to achieve in practice. This article presents an alternative method known as inverse patch transfer functions, designed to identify source velocities and developed in the framework of the European SILENCE project. This method is based on the definition of a virtual cavity, the double measurement of the pressure and particle velocity fields on the aperture surfaces of this volume, divided into elementary areas called patches and the inversion of impedances matrices, numerically computed from a modal basis obtained by FEM. Theoretically, the method is applicable to sources with complex 3D geometries and measurements can be carried out in a non-anechoic environment even in the presence of other stationary sources outside the virtual cavity. In the present paper, the theoretical background of the iPTF method is described and the results (numerical and experimental) for a source with simple geometry (two baffled pistons driven in antiphase) are presented and discussed.

  11. High incidence of interleukin 10 mRNA but not interleukin 2 mRNA detected in human breast tumours.

    PubMed Central

    Venetsanakos, E.; Beckman, I.; Bradley, J.; Skinner, J. M.

    1997-01-01

    Despite the presence of a lymphocytic infiltrate in solid cancers, the failure for tumour growth to be contained suggests an inadequate immune response to the tumour. Poor cytotoxicity exerted by tumour-infiltrating lymphocytes (TILs) against tumour cells in vitro, combined with continued tumour growth in vivo, suggests deficiencies in TIL function or numbers. Various theories have been postulated to explain how tumour cells may escape immunosurveillance and control. One of the many hypotheses is the failure of production of cytokines, which are necessary for T cells to mediate their function. Thus, the expression of cytokine mRNA in human breast tumour sections was investigated by reverse transcriptase polymerase chain reaction (RT-PCR) with cytokine-specific primers. A relatively consistent finding was detection of interleukin (IL) 10 mRNA among the tumours. No IL-2 and little IL-4 mRNA was detected in the tumours. IL-6 and IL-10 mRNA was detected in only one and two of the normal breast tissues respectively. IL-2, IL-4 and tumour necrosis factor (TNF)-alpha mRNA was not detected in any of the normal breast tissues. The reduced function of TILs may be related to IL-10, which has known inhibitory effects on T-cell activation. Images Figure 1 PMID:9192989

  12. MeV electron acceleration at 1 kHz with <10 mJ laser pulses

    NASA Astrophysics Data System (ADS)

    Salehi, Fatholah; Goers, Andy; Hine, George; Feder, Linus; Kuk, Donghoon; Miao, Bo; Woodbury, Daniel; Kim, Ki-Yong; Milchberg, Howard

    2017-01-01

    We demonstrate laser driven acceleration of electrons to MeV-scale energies at 1 kHz repetition rate using <10 mJ pulses focused on near-critical density He and H2 gas jets. Using the H2 gas jet, electron acceleration to 0.5 MeV in 10 fC bunches was observed with laser pulse energy as low as 1.3 mJ. Increasing the pulse energy to 10 mJ, we measure 1pC charge bunches with >1 MeV energy for both He and H gas jets. Such a high repetition rate, high flux ultrafast source has immediate application to time resolved probing of matter for scientific, medical, or security applications, either using the electrons directly or using a high-Z foil converter to generate ultrafast γ-rays. This work is supported by the US Department of Energy, the National Science Foundation, and the Air Force Office of Scientific Research.

  13. The 0.9 and 1.3 THz Superconducting HEB Mixer Receiver for the ASTE 10 m Telescope

    NASA Astrophysics Data System (ADS)

    Shiino, T.; Furuya, R.; Soma, T.; Sakai, T.; Watanabe, Y.; Sakai, N.; Jiang, L.; Ohguchi, O.; Maezawa, H.; Yamakura, T.; Yamamoto, S.

    2013-10-01

    We have developed low-noise waveguide-type superconducting hot electron bolometer (HEB) mixers for astronomical observations in the 0.8-1.0 and 1.3-1.5 THz bands, by using a relatively thick NbTiN superconducting film (10.8 nm). The receiver noise temperature of 350 K (DSB) at 0.81 THz and 490 K at 1.475 THz has been achieved. We have built the 0.8-1.0/1.3-1.5 THz dual band heterodyne receiver using these low noise HEB mixers, and have installed it on the ASTE (Atacama Submillimeter Telescope Experiment) 10 m telescope in Chile in 2011. The 13CO emission (J = 8-7 : 0.8813 THz) has successfully been detected toward the Orion A molecular cloud with our HEB mixer receiver.

  14. SIM.EM-K3 Key comparison of 10 mH inductance standards at 1 kHz

    NASA Astrophysics Data System (ADS)

    Moreno, J. A.; Côté, M.; Koffman, A.; Castro, B. I.; Vasconcellos, R. de Barros e.; Kyriazis, G.; Cazabat, M.; Izquierdo, D.; Faverio, C.; Slomovitz, D.

    2016-01-01

    A key comparison of 10 mH inductance standards at 1 kHz has been carried out with the participation of seven National Metrology Institutes of the Inter-American Metrology System, within the frame of the International Committee for Weights and Measures Mutual Recognition Arrangement (MRA), which was piloted by CENAM, Mexico. Three previously characterized commercial inductors, contained in individual enclosures with controlled temperature were used as traveling standards. This document presents the results and technical details of the comparison. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  15. Properties of nanocrystalline Fe75Si15M10 (M-Cr and Al) powders prepared by mechanical alloying.

    PubMed

    Kalita, M P C; Perumal, A; Srinivasan, A; Pandey, Brajesh; Verma, H C

    2008-08-01

    We report the structural and magnetic properties of the nanocrystalline Fe75Si15M10 (M-Al and Cr) powders prepared by mechanical alloying. The milling process produced a non-equilibrium solid solutions of bcc alpha-Fe(Si,Cr) and alpha-Fe(Si,Al). The average dislocation density increases and the average crystallite size decreases with increasing milling time. Magnetic property studies show that the coercivity of the sample increases and magnetization of the sample decreases with increasing milling time. The evolution of a non-equilibrium solid solution and the resulting magnetic properties of nanocrystalline powders are explained on the basis of Neel theory and modified random anisotropy model proposed by Shen et al.

  16. Identifying Meteor Streams Containing 10-m Bolides in Near-Earth Space and Determining their Temporal Evolution

    NASA Astrophysics Data System (ADS)

    Lai, H.; Russell, C. T.; Wei, H.; Delzanno, G.; Connors, M. G.

    2013-12-01

    The collision rate of small bodies orbiting the Sun increases with decreasing size. While small bodies in the 10-m class are difficult to detect from Earth, they are relatively easily detected by interplanetary spacecraft with magnetometers. A 10m body need be struck by a body only 20 cm across (traveling at 20 km/s) to be completely disrupted. The solar wind will sweep up the charged nano-scale dust as it flows through the debris forming a magnetic cloud. Because of the large size of the magnetic cloud only a small drop in the solar wind speed is needed to provide the momentum flux required to accelerate the cloud radially from the Sun. The cloud is carried outward and can be detected by any one of several interplanetary spacecraft. This procedure was first utilized on debris co-orbiting with the comet 2201 Oljato as monitored beginning in 1978 by the Pioneer Venus Orbiter and followed up by Venus Express that is still in operation. The meteoroid trail dissipated in just 30 years. We have used ACE, Wind and STEREO to identify a meteor stream co-orbiting with asteroid 138175 whose descending node is aligned with the Sun and the Earth on about April 17 each year. We have followed this trail from 1998 to the present and find that material extends to over 30° in front of the asteroid. It has been a steady producer of collisions over the last 15 years. The period of very close approach of this material to Earth may be over for a while but the material should be accessible by robotic or crewed missions as the orbit of 139175 has only a modest eccentricity and inclination to the ecliptic plane. Matching orbits with it should be similar in difficulty to a Venus flyby mission.

  17. Heart rate recovery after the 10-m incremental shuttle walking test in older adults with intellectual disabilities.

    PubMed

    Oppewal, Alyt; Hilgenkamp, Thessa I M; van Wijck, Ruud; Evenhuis, Heleen M

    2014-03-01

    Heart rate recovery (HRR) after exercise is an independent predictor for cardiovascular and all-cause mortality. To investigate the usefulness of HRR in cardiorespiratory exercise testing in older adults with intellectual disabilities (ID), the aims of this study were (a) to assess HRR in older adults with ID after the 10-m incremental shuttle walking test (ISWT) and (b) its association with personal characteristics (gender, age, distance walked on the ISWT, level of ID, genetic syndrome causing ID, autism, behavioral problems, and peak heart rate (HRpeak)). HRR was assessed after the 10-m incremental shuttle walking test in 300 older adults (>50 years) with borderline to profound ID. HRR was defined as the change from HRpeak during the ISWT to heart rate measured after 1, 2, 3, 4, and 5 min of passive recovery. The largest decrease in heart rate was in the first minute of recovery leveling off toward the fifth minute of recovery. An abnormal HHR (≤12 bpm) was seen in 36.1% of the participants with Down syndrome (DS) and in 30.7% of the participants with ID by other causes. After the fifth minute the heart rates of 69.4% of the participants with DS and of 61.4% of the participants with ID by other causes returned to resting levels. HRpeak and distance walked on the ISWT were positively related to all HRR measures. More severe ID was negatively related and having DS positively related to HRR after 3-5 min of recovery. The other characteristics were not significantly associated to HRR. HRR is a potentially useful outcome measure in cardiorespiratory fitness testing of older adults with ID with a direct, objective, and non-invasive measurement. Further research is needed to identify the relation between HRR and adverse health outcomes in this population.

  18. MeV electron acceleration at 1kHz with <10 mJ laser pulses

    NASA Astrophysics Data System (ADS)

    Salehi, Fatholah; Goers, Andy; Hine, George; Feder, Linus; Kuk, Donghoon; Kim, Ki-Yong; Milchberg, Howard

    2016-10-01

    We demonstrate laser driven acceleration of electrons at 1 kHz repetition rate with pC charge above 1MeV per shot using < 10 mJ pulse energies focused on a near-critical density He or H2 gas jet. Using the H2 gas jet, electron acceleration to 0.5 MeV in 10 fC bunches was observed with laser pulse energy as low as 1.3mJ . Using a near-critical density gas jet sets the critical power required for relativistic self-focusing low enough for mJ scale laser pulses to self- focus and drive strong wakefields. Experiments and particle-in-cell simulations show that optimal drive pulse duration and chirp for maximum electron bunch charge and energy depends on the target gas species. High repetition rate, high charge, and short duration electron bunches driven by very modest pulse energies constitutes an ideal portable electron source for applications such as ultrafast electron diffraction experiments and high rep. rate γ-ray production. This work is supported by the US Department of Energy, the National Science Foundation, and the Air Force Office of Scientific Research.

  19. Search for the CO-dark Mass in the Central Molecular Zone by using the ASTE 10-m Telescope

    NASA Astrophysics Data System (ADS)

    Tanaka, Kunihiko

    2017-01-01

    Atomic carbon (C0) is one of the most abundant carbon-bearing species in the interstellar molecular gas, and its submillimeter lines are good tracers of low-density molecular clouds which are often dark in CO rotational lines. We present a new map of the central 150 pc region of the Milky Way in the 500 GHz [CI] line, which has been recently obtained with the ASTE 10-m telescope. The [CI] emission is brightest toward the central 5-pc region, where massive GMCs are absent. This [CI]-bright region is approximately centered toward Sgr A*, covering the entire circum-nuclear ring (CND) and the western part of the 50-km/s cloud. The C0/CO abundance ratio is 0.5-2 there, and the highest ratio is observed toward the CND but just outside of the 2-pc ring of dense gas. This discovery may suggest that the CO-dark component occupies a significant fraction of the molecular gas in the circumnuclear region.

  20. A 10 mK scanning tunneling microscope operating in ultra high vacuum and high magnetic fields.

    PubMed

    Assig, Maximilian; Etzkorn, Markus; Enders, Axel; Stiepany, Wolfgang; Ast, Christian R; Kern, Klaus

    2013-03-01

    We present design and performance of a scanning tunneling microscope (STM) that operates at temperatures down to 10 mK providing ultimate energy resolution on the atomic scale. The STM is attached to a dilution refrigerator with direct access to an ultra high vacuum chamber allowing in situ sample preparation. High magnetic fields of up to 14 T perpendicular and up to 0.5 T parallel to the sample surface can be applied. Temperature sensors mounted directly at the tip and sample position verified the base temperature within a small error margin. Using a superconducting Al tip and a metallic Cu(111) sample, we determined an effective temperature of 38 ± 1 mK from the thermal broadening observed in the tunneling spectra. This results in an upper limit for the energy resolution of ΔE = 3.5 kBT = 11.4 ± 0.3 μeV. The stability between tip and sample is 4 pm at a temperature of 15 mK as demonstrated by topography measurements on a Cu(111) surface.

  1. High-cycle fatigue of 10M Ni-Mn-Ga magnetic shape memory alloy in reversed mechanical loading

    NASA Astrophysics Data System (ADS)

    Aaltio, I.; Soroka, A.; Ge, Y.; Söderberg, O.; Hannula, S.-P.

    2010-07-01

    Application of Ni-Mn-Ga magnetic shape memory alloys in magnetic-field-induced actuation relies on their performance in long-term high-cycle fatigue. In this paper the performance and changes in the microstructure of a Ni-Mn-Ga 10M martensite single crystal material are reported in a long-term mechanically induced shape change cycling. The longest test was run for 2 × 109 cycles at a frequency of 250 Hz and a strain amplitude of ± 1%. After the test a clear increase of the dynamic stiffness of the material was detected. Three specimens out of ten were cycled until fracture occurred and their fracture mechanism was studied. It was observed that the macroscopic crack growth took place roughly at a 45° angle with respect to the loading direction that was along the lang100rang crystallographic direction of the sample. The macroscopic fracture plane seemed to correspond roughly to the {111} crystal planes. On a microscopic scale the fracture propagated in a step-like manner at least partly along crystallographic planes. The steps at the fracture plane correspond to the {101} twin planes, with the height of steps along the lang101rang direction. The final fracture of the samples occurred in a brittle manner after the critical stress was exceeded.

  2. B cells expressing IL-10 mRNA modulate memory T cells after DNA-Hsp65 immunization

    PubMed Central

    Fontoura, I. C.; Trombone, A.P.F.; Almeida, L. P.; Lorenzi, J. C. C.; Rossetti, R. A. M.; Malardo, T.; Padilha, E.; Schluchting, W.; Silva, R. L. L.; Gembre, A. F.; Fiuza, J. E. C.; Silva, C. L.; Panunto-Castelo, A.; Coelho-Castelo, A. A. M.

    2015-01-01

    In DNA vaccines, the gene of interest is cloned into a bacterial plasmid that is engineered to induce protein production for long periods in eukaryotic cells. Previous research has shown that the intramuscular immunization of BALB/c mice with a naked plasmid DNA fragment encoding the Mycobacterium leprae 65-kDa heat-shock protein (pcDNA3-Hsp65) induces protection against M. tuberculosis challenge. A key stage in the protective immune response after immunization is the generation of memory T cells. Previously, we have shown that B cells capture plasmid DNA-Hsp65 and thereby modulate the formation of CD8+ memory T cells after M. tuberculosis challenge in mice. Therefore, clarifying how B cells act as part of the protective immune response after DNA immunization is important for the development of more-effective vaccines. The aim of this study was to investigate the mechanisms by which B cells modulate memory T cells after DNA-Hsp65 immunization. C57BL/6 and BKO mice were injected three times, at 15-day intervals, with 100 µg naked pcDNA-Hsp65 per mouse. Thirty days after immunization, the percentages of effector memory T (TEM) cells (CD4+ and CD8+/CD44high/CD62Llow) and memory CD8+ T cells (CD8+/CD44high/CD62Llow/CD127+) were measured with flow cytometry. Interferon γ, interleukin 12 (IL-12), and IL-10 mRNAs were also quantified in whole spleen cells and purified B cells (CD43−) with real-time qPCR. Our data suggest that a B-cell subpopulation expressing IL-10 downregulated proinflammatory cytokine expression in the spleen, increasing the survival of CD4+ TEM cells and CD8+ TEM/CD127+ cells. PMID:26397973

  3. Reconstructing the 3D fracture distribution model from core (10 cm) to outcrop (10 m) and lineament (10 km) scales

    NASA Astrophysics Data System (ADS)

    Darcel, C.; Davy, P.; Bour, O.; de Dreuzy, J.

    2006-12-01

    model from both outcrop and well fracturing observations, and we discuss the consistency between the along-core fracturing intensity profile, the outcrop fracture traces, and the lineament maps. In the Forsmark site investigated by SKB, we conclude that the power-law distribution model is statistically consistent from core scale (80 mm) to outcrop scale (~10 m); the consistency with the lineament scale (10 km) is still questionable. An important subhorizontal fracturing exists at shallow depth, but it does not seems to affect the statistics of highly dipping fractures.

  4. Semi-classical Electrodynamics

    NASA Astrophysics Data System (ADS)

    Lestone, John

    2016-03-01

    Quantum electrodynamics is complex and its associated mathematics can appear overwhelming for those not trained in this field. We describe semi-classical approaches that can be used to obtain a more intuitive physical feel for several QED processes including electro-statics, Compton scattering, pair annihilation, the anomalous magnetic moment, and the Lamb shift, that could be taught easily to undergraduate students. Any physicist who brings their laptop to the talk will be able to build spread sheets in less than 10 minutes to calculate g/2 =1.001160 and a Lamb shift of 1057 MHz.

  5. Different cutoff values for 10-m walking speed simply classification of walking independence in stroke patients with or without cognitive impairment

    PubMed Central

    Yoshimoto, Yoshinobu; Oyama, Yukitsuna; Tanaka, Mamoru

    2015-01-01

    [Purpose] The aim of this study was to determine the threshold for classifying walking independence in stroke patients with and without cognitive disorders. [Subjects] The subjects were 130 patients with initial stroke hemiplegia. [Methods] The following factors were analyzed for associations with walking independence: Brunnstrom stage, one-leg standing time on the paralytic side, one-leg standing time on the non-paralytic side, and 10-m walking speed. We classified the patients with Mini-Mental State Examination (MMSE) scores ≥24 points into the high-score group and those with MMSE scores of ≤23 points into the low-score group and examined the main factors and cutoff values associated with walking independence in each group. [Results] The high-score group included 69 subjects (53.1%), and the low-score group included 61 subjects (46.9%). The primary factor associated with high MMSE scores among the stroke patients was the 10-m walking time. Using a cutoff level for the 10-m walking speed of 41.4 m/min resulted in a positive likelihood ratio of 6.3. The primary factor associated with low MMSE scores among the stroke patients was the 10-m walking time. Using a cutoff level for the 10-m walking speed of 48.0 m/min resulted in a positive likelihood ratio of 7.6. [Conclusion] The cutoff value for the 10-m walking speed can be used to evaluate walking independence in patients with stroke among patients with high or low MMSE scores. PMID:26157250

  6. Different cutoff values for 10-m walking speed simply classification of walking independence in stroke patients with or without cognitive impairment.

    PubMed

    Yoshimoto, Yoshinobu; Oyama, Yukitsuna; Tanaka, Mamoru

    2015-05-01

    [Purpose] The aim of this study was to determine the threshold for classifying walking independence in stroke patients with and without cognitive disorders. [Subjects] The subjects were 130 patients with initial stroke hemiplegia. [Methods] The following factors were analyzed for associations with walking independence: Brunnstrom stage, one-leg standing time on the paralytic side, one-leg standing time on the non-paralytic side, and 10-m walking speed. We classified the patients with Mini-Mental State Examination (MMSE) scores ≥24 points into the high-score group and those with MMSE scores of ≤23 points into the low-score group and examined the main factors and cutoff values associated with walking independence in each group. [Results] The high-score group included 69 subjects (53.1%), and the low-score group included 61 subjects (46.9%). The primary factor associated with high MMSE scores among the stroke patients was the 10-m walking time. Using a cutoff level for the 10-m walking speed of 41.4 m/min resulted in a positive likelihood ratio of 6.3. The primary factor associated with low MMSE scores among the stroke patients was the 10-m walking time. Using a cutoff level for the 10-m walking speed of 48.0 m/min resulted in a positive likelihood ratio of 7.6. [Conclusion] The cutoff value for the 10-m walking speed can be used to evaluate walking independence in patients with stroke among patients with high or low MMSE scores.

  7. Querying Semi-Structured Data

    NASA Technical Reports Server (NTRS)

    Abiteboul, Serge

    1997-01-01

    The amount of data of all kinds available electronically has increased dramatically in recent years. The data resides in different forms, ranging from unstructured data in the systems to highly structured in relational database systems. Data is accessible through a variety of interfaces including Web browsers, database query languages, application-specic interfaces, or data exchange formats. Some of this data is raw data, e.g., images or sound. Some of it has structure even if the structure is often implicit, and not as rigid or regular as that found in standard database systems. Sometimes the structure exists but has to be extracted from the data. Sometimes also it exists but we prefer to ignore it for certain purposes such as browsing. We call here semi-structured data this data that is (from a particular viewpoint) neither raw data nor strictly typed, i.e., not table-oriented as in a relational model or sorted-graph as in object databases. As will seen later when the notion of semi-structured data is more precisely de ned, the need for semi-structured data arises naturally in the context of data integration, even when the data sources are themselves well-structured. Although data integration is an old topic, the need to integrate a wider variety of data- formats (e.g., SGML or ASN.1 data) and data found on the Web has brought the topic of semi-structured data to the forefront of research. The main purpose of the paper is to isolate the essential aspects of semi- structured data. We also survey some proposals of models and query languages for semi-structured data. In particular, we consider recent works at Stanford U. and U. Penn on semi-structured data. In both cases, the motivation is found in the integration of heterogeneous data.

  8. Phenomenology of a semi-Dirac semi-Weyl semimetal

    NASA Astrophysics Data System (ADS)

    Banerjee, S.; Pickett, W. E.

    2012-08-01

    We extend the semiclassical study of fermionic particle-hole symmetric semi-Dirac (more appropriately, semi-Dirac semi-Weyl) dispersion of quasiparticles, ɛK=±(kx2/2m)2+(vky)2)=±ɛ0Kx4+Ky2 in dimensionless units, discovered computationally in oxide heterostructures by Pardo and collaborators. This unique system is a highly anisotropic sister phase of both (symmetric) graphene and what has become known as a Weyl semimetal, having 1/2≈v independent of energy, and 1/2∝m-1/2ɛ being very strongly dependent on energy (ɛ) and depending only on the effective mass m. Each of these systems is distinguished by bands crossing (sometimes referred to as touching) at a point Fermi surface, with one consequence being that for this semi-Dirac system the ratio |χorb/χsp| of orbital to spin susceptibilities diverges at low doping. We extend the study of the low-energy behavior of the semi-Dirac system, finding the plasmon frequency to be highly anisotropic while the Hall coefficient scales with carrier density in the usual manner. The Faraday rotation behavior is also reported. For Klein tunneling at normal incidence on an arbitrarily oriented barrier, the kinetic energy mixes both linear (massless) and quadratic (massive) contributions depending on orientation. Analogous to graphene, perfect transmission occurs under resonant conditions, except for the specific orientation that eliminates massless dispersion. Comparisons of the semi-Dirac system are made throughout with both other types of point Fermi surface systems.

  9. DNA synthesis and microtubule assembly-related events in fertilized Paracentrotus lividus eggs: reversible inhibition by 10 mM procaine.

    PubMed

    Raymond, M N; Foucault, G; Coffe, G; Pudles, J

    1986-04-01

    This report describes the effects of 10 mM procaine on microtubule assembly and on DNA synthesis, as followed by [3H]colchicine binding assays and [3H]thymidine incorporation respectively, in fertilized Paracentrotus lividus eggs. In the absence of microtubule assembly inhibitors, about 25% of the total egg tubulin is submitted to two cycles of polymerization prior to the first cell division, this polymerization process precedes DNA synthesis. If the zygotes are treated with 10 mM procaine in the course of the cell cycle, tubulin polymerization is inhibited or microtubules are disassembled. DNA synthesis is inhibited when procaine treatment is performed 10 min, before the initiation of the S-period. However, when the drug is applied in the course of this synthetic period, the process is normally accomplished, but the next S-period becomes inhibited. Moreover, procaine treatment increases the cytoplasmic pH of the fertilized eggs by about 0.6 to 0.8 pH units. This pH increase precedes microtubule disassembly and inhibition of DNA synthesis. Washing out the drug induces a decrease of the intracellular pH which returns to about the same value as that of the fertilized egg controls. This pH change is then followed by the reinitiation of microtubule assembly, DNA synthesis and cell division. Our results show that the inhibition of both tubulin polymerization and DNA synthesis in fertilized eggs treated with 10 mM procaine, appears to be related to the drug-induced increase in cytoplasmic pH.

  10. Absence of ocular effects after either single or repeated exposure to 10 mW/cm(2) from a 60 GHz CW source.

    PubMed

    Kues, H A; D'Anna, S A; Osiander, R; Green, W R; Monahan, J C

    1999-12-01

    This study was designed to examine ocular effects associated with exposure to millimeter waves (60 GHz). Rabbits served as the primary experimental subjects. To confirm the results of the rabbit experiments in a higher species, the second phase of the study used nonhuman primates (Macaca mulatta). First, this study used time-resolved infrared radiometry to assess the field distribution patterns produced by different antennas operating at 60 GHz. These results allowed us to select an antenna that produced a uniform energy distribution and the best distance at which to expose our experimental subjects. The study then examined ocular changes after exposure at an incident power density of 10 mW/cm(2). Acute exposure of both rabbits and nonhuman primates consisted of a single 8 h exposure, and the repeated exposure protocol consisted of five separate 4 h exposures on consecutive days. One eye in each animal was exposed and the contralateral eye served as the sham-exposed control. After postexposure diagnostic examinations, animals were euthanized and the eyes were removed. Ocular tissue was examined by both light and transmission electron microscopy. Neither microscopic examinations nor the diagnostic procedures performed on the eyes of acute and repeatedly exposed rabbits found any ocular changes that could be attributed to millimeter-wave exposure at 10 mW/cm(2). Examination of the primates after comparable exposures also failed to detect any ocular changes due to exposure. On the basis of our results, we conclude that single or repeated exposure to 60 GHz CW radiation at 10 mW/cm(2) does not result in any detectable ocular damage.

  11. Semi-transparent solar cells

    NASA Astrophysics Data System (ADS)

    Sun, J.; Jasieniak, J. J.

    2017-03-01

    Semi-transparent solar cells are a type of technology that combines the benefits of visible light transparency and light-to-electricity conversion. One of the biggest opportunities for such technologies is in their integration as windows and skylights within energy-sustainable buildings. Currently, such building integrated photovoltaics (BIPV) are dominated by crystalline silicon based modules; however, the opaque nature of silicon creates a unique opportunity for the adoption of emerging photovoltaic candidates that can be made truly semi-transparent. These include: amorphous silicon-, kesterite-, chalcopyrite-, CdTe-, dye-sensitized-, organic- and perovskite- based systems. For the most part, amorphous silicon has been the workhorse in the semi-transparent solar cell field owing to its established, low-temperature fabrication processes. Excitement around alternative classes, particularly perovskites and the inorganic candidates, has recently arisen because of the major efficiency gains exhibited by these technologies. Importantly, each of these presents unique opportunities and challenges within the context of BIPV. This topic review provides an overview into the broader benefits of semi-transparent solar cells as building-integrated features, as well as providing the current development status into all of the major types of semi-transparent solar cells technologies.

  12. Elucidation of the Corrosion Inhibition of Mild Steel in 1.0 M HCl by Catechin Monomers from Commercial Green Tea Extracts

    NASA Astrophysics Data System (ADS)

    Nofrizal, S.; Rahim, Afidah A.; Saad, Bahruddin; Bothi Raja, P.; Shah, Affaizza M.; Yahya, S.

    2012-04-01

    The inhibitive action of commercial green tea extracts on mild steel (MS) in a 1.0 M hydrochloric acid solution was investigated by weight loss, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS). A high-performance liquid chromatographic (HPLC) analysis showed conclusively that of the eight catechin monomers and caffeine found in the original extracts, only four components were responsible for the inhibition of MS. The decreasing adsorption capacity of monomers on MS is related to the stereochemistry of molecules and the number of phenolic groups, and it is as follows: epigallocatechin gallate > epicatechin gallate > epigallocatechin > epicatechin. Adsorption of green tea extract constituent was found to follow Langmuir adsorption isotherm and the calculated Gibb's free energy values indicated the physisorption of inhibitor over MS surface. Physisorption was supported well by the potential zero charge (PZC) and molecular surface energy-level calculations.

  13. Synergistic of a coumarin derivative with potassium iodide on the corrosion inhibition of aluminum alloy in 1.0 M H2SO4

    NASA Astrophysics Data System (ADS)

    Mohamad, Abu Bakar; Kadhum, Abdul Amir H.; Al-Amiery, Ahmed A.; Ying, Lim Chai; Musa, Ahmed Y.

    2014-05-01

    Synergistic effects of the addition of KI on the corrosion inhibitive performance of a coumarin derivative on an aluminum alloy in 1.0 M H2SO4 at different temperatures were studied using various electrochemical measurements. Density functional theory was used to calculate the quantum chemical parameters of the coumarin derivative. The experimental results showed that the coumarin derivative is considered as a mixedtype inhibitor. The corrosion potential values were almost unchanged upon the addition of PBBC to the acidic solution. The inhibition efficiency increases with increasing inhibitor concentration and increases further in the presence of 6.02 mM KI but decreases significantly at higher temperature. The adsorption of PBBC obeyed the Langmuir isotherm, and being chemically adsorbed at lower temperatures, while physical adsorption is favoured at higher temperature. The theoretical results indicated that the coumarin derivative was adsorbed onto the surface of Al2024 through the sulfur, oxygen and nitrogen atoms.

  14. Semi-Markov Graph Dynamics

    PubMed Central

    Raberto, Marco; Rapallo, Fabio; Scalas, Enrico

    2011-01-01

    In this paper, we outline a model of graph (or network) dynamics based on two ingredients. The first ingredient is a Markov chain on the space of possible graphs. The second ingredient is a semi-Markov counting process of renewal type. The model consists in subordinating the Markov chain to the semi-Markov counting process. In simple words, this means that the chain transitions occur at random time instants called epochs. The model is quite rich and its possible connections with algebraic geometry are briefly discussed. Moreover, for the sake of simplicity, we focus on the space of undirected graphs with a fixed number of nodes. However, in an example, we present an interbank market model where it is meaningful to use directed graphs or even weighted graphs. PMID:21887245

  15. Coastal and Semi Enclosed Seas

    DTIC Science & Technology

    2016-06-07

    Numerical model process and sensitivity studies are conducted to better understand the dynamics and thermodynamics of shallow and deep semi-enclosed seas...and EAS domains. Shelley Riedlinger, running both EAS and Yellow Sea model codes: Pamela Posey obtains and provides atmospheric forcing, both real time...extends from 150 S latitude to 600 N latitude . Testing of this model included a spin-up of the model from 1994 to 1999 using the Navy Operational Global

  16. Dynamics of soil exploration by fine roots down to a depth of 10 m throughout the entire rotation in Eucalyptus grandis plantations

    PubMed Central

    Laclau, Jean-Paul; da Silva, Eder A.; Rodrigues Lambais, George; Bernoux, Martial; le Maire, Guerric; Stape, José L.; Bouillet, Jean-Pierre; Gonçalves, José L. de Moraes; Jourdan, Christophe; Nouvellon, Yann

    2013-01-01

    Although highly weathered soils cover considerable areas in tropical regions, little is known about exploration by roots in deep soil layers. Intensively managed Eucalyptus plantations are simple forest ecosystems that can provide an insight into the belowground growth strategy of fast-growing tropical trees. Fast exploration of deep soil layers by eucalypt fine roots may contribute to achieving a gross primary production that is among the highest in the world for forests. Soil exploration by fine roots down to a depth of 10 m was studied throughout the complete cycle in Eucalyptus grandis plantations managed in short rotation. Intersects of fine roots, less than 1 mm in diameter, and medium-sized roots, 1–3 mm in diameter, were counted on trench walls in a chronosequence of 1-, 2-, 3.5-, and 6-year-old plantations on a sandy soil, as well as in an adjacent 6-year-old stand growing in a clayey soil. Two soil profiles were studied down to a depth of 10 m in each stand (down to 6 m at ages 1 and 2 years) and 4 soil profiles down to 1.5–3.0 m deep. The root intersects were counted on 224 m2 of trench walls in 15 pits. Monitoring the soil water content showed that, after clear-cutting, almost all the available water stored down to a depth of 7 m was taken up by tree roots within 1.1 year of planting. The soil space was explored intensively by fine roots down to a depth of 3 m from 1 year after planting, with an increase in anisotropy in the upper layers throughout the rotation. About 60% of fine root intersects were found at a depth of more than 1 m, irrespective of stand age. The root distribution was isotropic in deep soil layers and kriged maps showed fine root clumping. A considerable volume of soil was explored by fine roots in eucalypt plantations on deep tropical soils, which might prevent water and nutrient losses by deep drainage after canopy closure and contribute to maximizing resource uses. PMID:23847645

  17. Final report on COOMET supplementary comparison of inductance at 10 mH and 100 mH at 1 kHz (COOMET.EM-S14)

    NASA Astrophysics Data System (ADS)

    Velychko, O.; Shevkun, S.

    2016-01-01

    An inter-comparison of 10 mH and 100 mH inductance standards has taken place within the framework of COOMET. The inter-comparison, piloted by State Enterprise 'Ukrmetrteststandard'-UMTS (Ukraine), has involved four laboratories, including one who is a member of another regional metrological organization - EURAMET (GUM, Poland). The results presented in this report show that there are significant differences between some laboratory representations of the henry. However, the agreement demonstrated by the inter-comparison provides confidence in maintaining traceability for the henry. KEY WORDS FOR SEARCH Inter-comparison, inductance standard, traceability, regional metrological organization Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  18. The 10 m-resolution TINITALY DEM as a trans-disciplinary basis for the analysis of the Italian territory: Current trends and new perspectives

    NASA Astrophysics Data System (ADS)

    Tarquini, Simone; Nannipieri, Luca

    2017-03-01

    The increasing availability of high resolution digital elevation models (DEMs) is changing our viewpoint towards Earth surface landforms. Nevertheless, large-coverage, intermediate-resolution DEMs are still largely used, and can be the ideal choice in several applications based on the processing of spatially-integrated information. In 2012 the Istituto Nazionale di Geofisica e Vulcanologia opened a website for the free download of the "TINTALY" Digital Elevation Model (DEM), which covers the whole Italian territory. Since then, about 700 users from 28 different countries have been accredited for data download, and a report of 4 years of data dissemination and use is presented. The analysis of the intended use reveals that the 10 m-resolution, seamless TINITALY DEM is of use for an extremely assorted research community. Accredited users are working in virtually any branch of the Earth Sciences (e.g. Volcanology, Seismology, and Geomorphology), in spatially integrated humanities (e.g. History and Archaeology), and in other thematic areas such as in applied Physics and Zoology. Many users are also working in local administrations (e.g. Regions and Municipalities) for civil protection or land use planning purposes. In summary, the documented activity shows that the dissemination of seamless, large coverage elevation datasets can fertilize the technological progress of the whole society providing a significant benefit to stakeholders.

  19. Synthesis, Structure, and Electrochemical Properties of Na3MB5O10 (M = Fe, Co) Containing M(2+) in Tetrahedral Coordination.

    PubMed

    Strauss, Florian; Rousse, Gwenaëlle; Sougrati, Moulay Tahar; Dalla Corte, Daniel Alves; Courty, Matthieu; Dominko, Robert; Tarascon, Jean-Marie

    2016-12-19

    In the search for new cathode materials for sodium ion batteries, the exploration of polyanionic compounds has led to attractive candidates in terms of high redox potential and cycling stability. Herein we report the synthesis of the two new sodium transition-metal pentaborates Na3MB5O10 (M = Fe, Co), where Na3FeB5O10 represents the first sodium iron borate reported at present. By means of synchrotron X-ray diffraction, we reveal a layered structure consisting of pentaborate B5O10 groups connected through M(2+) in tetrahedral coordination, providing possible three-dimensional Na-ion migration pathways. Inspired by these structural features, we examined the electrochemical performances versus sodium and showed that Na3FeB5O10 is active at an average potential of 2.5 V vs Na(+)/Na(0), correlated to the Fe(3+)/Fe(2+) redox couple as deduced from ex situ Mössbauer measurements. This contrasts with the case for Na3CoB5O10, which is electrochemically inactive. Moreover, we show that their electrochemical performances are kinetically limited, as deduced by complementary ac/dc conductivity measurements, hence confirming once again the complexity in designing high-performance borate-based electrodes.

  20. Enhanced π-Back-Donation as a Way to Higher Coordination Numbers in d(10) [M(NHC)n ] Complexes: A DFT Study.

    PubMed

    Nitsch, Jörn; Wolters, Lando P; Fonseca Guerra, Célia; Bickelhaupt, F Matthias; Steffen, Andreas

    2017-01-12

    We aim to understand the electronic factors determining the stability and coordination number of d(10) transition-metal complexes bearing N-heterocyclic carbene (NHC) ligands, with a particular emphasis on higher coordinated species. In this DFT study on the formation and bonding of Group 9-12 d(10) [M(NHC)n ] (n=1-4) complexes, we found that all metals form very stable [M(NHC)2 ] complexes, but further coordination depends on the specific interplay of 1) the interaction energy (ΔEint ) between the [M(NHC)n-1 ] (n=2-4) fragment and the incoming NHC ligand, and 2) the strain energy (ΔEstrain ) associated with bending of the linear NHC-M-NHC arrangement. The key observation is that ΔEstrain , which is an antagonist for higher coordination numbers, can significantly be lowered by M→NHC π*-back-donation. This leads to favorable thermodynamics for n=3-4 for highly electrophilic metals in our study, and thus presents a general design motif to achieve coordination numbers beyond two. The scope of our findings extends beyond the NHC model systems and has wider implications for the synthesis of d(10) [MLn ] complexes and their catalytic activity.

  1. 10 m/25 Gbps LiFi transmission system based on a two-stage injection-locked 680 nm VCSEL transmitter.

    PubMed

    Lu, Hai-Han; Li, Chung-Yi; Chu, Chien-An; Lu, Ting-Chien; Chen, Bo-Rui; Wu, Chang-Jen; Lin, Dai-Hua

    2015-10-01

    A 10  m/25  Gbps light-based WiFi (LiFi) transmission system based on a two-stage injection-locked 680 nm vertical-cavity surface-emitting laser (VCSEL) transmitter is proposed. A LiFi transmission system with a data rate of 25 Gbps is experimentally demonstrated over a 10 m free-space link. To the best of our knowledge, it is the first time a two-stage injection-locked 680 nm VCSEL transmitter in a 10  m/25  Gbps LiFi transmission system has been employed. Impressive bit error rate performance and a clear eye diagram are achieved in the proposed systems. Such a 10  m/25  Gbps LiFi transmission system provides the advantage of a communication link for higher data rates that could accelerate the deployment of visible laser light communication.

  2. Serum FSH level below 10 mIU/mL at twelve years old is an index of spontaneous and cyclical menstruation in Turner syndrome.

    PubMed

    Aso, Keiko; Koto, Shinobu; Higuchi, Asako; Ariyasu, Daisuke; Izawa, Masako; Miyamoto Igaki, Junko; Hasegawa, Yukihiro

    2010-01-01

    The gonadal function of patients with Turner syndrome (TS) is variable. Individuals with mosaicism characterized by 45,X/46,XX or 45,X/47,XXX are more likely to experience spontaneous menarche compared with other karyotypes. Prepubertal gonadotropins of TS patients with spontaneous menarche are reportedly normal or significantly lower than those of patients with induced menarche. The present study investigated an index of spontaneous and cyclical menstruation at 10-12 years old in TS. Subjects comprised 50 patients with TS, divided into three groups: Group A (n=7), with spontaneous menarche before 16 years old and regular menstruation for at least 1 year and 6 months; Group B (n=6), with irregular menstruation since menarche leading to secondary amenorrhea despite spontaneous menarche before 16 years old; and Group C (n=37), without spontaneous breast budding before 14 years old or without spontaneous menarche before 16 years old. Karyotype, LH and FSH concentrations at 10 and 12 years old were analyzed retrospectively. Spontaneous and cyclical menstruation was more frequently observed in TS with mosaicism characterized by 45,X/46,XX or 45,X/47,XXX than in TS with other karyotypes, as previously described. Spontaneous and cyclical menstruation in TS was observed when serum FSH level was <10 mIU/mL at 12 years old, suggesting this FSH level as an index of spontaneous and cyclical menstruation in TS.

  3. The ARL/FED Anechoic Chamber

    DTIC Science & Technology

    1981-08-04

    Attn: F. E. Geib National Bureau of Standards Code 1942 Aerodynamics Section (Copy No. 25) Washington, DC 20234 Attn: D. S. Pallet David W. Taylor...Dated 4 August 1981 David W. Taylor Naval Ship R & D Center Dr . James H. Dittmar Attn: J. Henry MS 501-4 (Copy No. 39) NASA Lewis Research Center21000...Brookpark Road• Naval Research Laboratory Cleveland, OH 44135 Washington, DC 20390 (Copy No. 50) Attn: R. J. Hansen (Copy No. 40) Dr . R. P. Dring United

  4. Bright features in Neptune on 2013-2015 from ground-based observations with small (40 cm) and large telescopes (10 m)

    NASA Astrophysics Data System (ADS)

    Hueso, Ricardo; Delcroix, Marc; Baranec, Christoph; Sánchez-Lavega, Agustín; María Gómez-Forrellad, Josep; Félix Rojas, Jose; Luszcz-Cook, Statia; de Pater, Imke; de Kleer, Katherine; Colas, François; Guarro, Joan; Goczynski, Peter; Jones, Paul; Kivits, Willem; Maxson, Paul; Phillips, Michael; Sussenbach, John; Wesley, Anthony; Hammel, Heidi B.; Pérez-Hoyos, Santiago; Mendikoa, Iñigo; Riddle, Reed; Law, Nicholas M.; Sayanagi, Kunio

    2015-11-01

    Observations of Neptune over the last few years obtained with small telescopes (30-50 cm) have resulted in several detections of bright features on the planet. In 2013, 2014 and 2015, different observers have repeatedly observed features of high contrast at Neptune’s mid-latitudes using long-pass red filters. This success at observing Neptune clouds with such small telescopes is due to the presence of strong methane absorption bands in Neptune’s spectra at red and near infrared wavelengths; these bands provide good contrast for elevated cloud structures. In each case, the atmospheric features identified in the images survived at least a few weeks, but were essentially much more variable and apparently shorter-lived, than the large convective system recently reported on Uranus [de Pater et al. 2015]. The latest and brightest spot on Neptune was first detected on July 13th 2015 with the 2.2m telescope at Calar Alto observatory with the PlanetCam UPV/EHU instrument. The range of wavelengths covered by PlanetCam (from 350 nm to the H band including narrow-band and wide-band filters in and out of methane bands) allows the study of the vertical cloud structure of this bright spot. In particular, the spot is particularly well contrasted at the H band where it accounted to a 40% of the total planet brightness. Observations obtained with small telescopes a few days later provide a good comparison that can be used to scale similar structures in 2013 and 2014 that were observed with 30-50 cm telescopes and the Robo-AO instrument at Palomar observatory. Further high-resolution observations of the 2015 event were obtained in July 25th with the NIRC2 camera in the Keck 2 10-m telescope. These images show the bright spot as a compact bright feature in H band with a longitudinal size of 8,300 km and a latitudinal extension of 5,300 km, well separated from a nearby bright band. The ensemble of observations locate the structure at -41º latitude drifting at about +24.27º/day or

  5. Static and wind tunnel near-field/far-field jet noise measurements from model scale single-flow base line and suppressor nozzles. Summary report. [conducted in the Boeing large anechoic test chamber and the NASA-Ames 40by 80-foot wind tunnel

    NASA Technical Reports Server (NTRS)

    Jaeck, C. L.

    1977-01-01

    A test program was conducted in the Boeing large anechoic test chamber and the NASA-Ames 40- by 80-foot wind tunnel to study the near- and far-field jet noise characteristics of six baseline and suppressor nozzles. Static and wind-on noise source locations were determined. A technique for extrapolating near field jet noise measurements into the far field was established. It was determined if flight effects measured in the near field are the same as those in the far field. The flight effects on the jet noise levels of the baseline and suppressor nozzles were determined. Test models included a 15.24-cm round convergent nozzle, an annular nozzle with and without ejector, a 20-lobe nozzle with and without ejector, and a 57-tube nozzle with lined ejector. The static free-field test in the anechoic chamber covered nozzle pressure ratios from 1.44 to 2.25 and jet velocities from 412 to 594 m/s at a total temperature of 844 K. The wind tunnel flight effects test repeated these nozzle test conditions with ambient velocities of 0 to 92 m/s.

  6. Semi-Markov Unreliability-Range Evaluator

    NASA Technical Reports Server (NTRS)

    Butler, Ricky W.

    1988-01-01

    Reconfigurable, fault-tolerant systems modeled. Semi-Markov unreliability-range evaluator (SURE) computer program is software tool for analysis of reliability of reconfigurable, fault-tolerant systems. Based on new method for computing death-state probabilities of semi-Markov model. Computes accurate upper and lower bounds on probability of failure of system. Written in PASCAL.

  7. Semi autonomous mine detection system

    NASA Astrophysics Data System (ADS)

    Few, Doug; Versteeg, Roelof; Herman, Herman

    2010-04-01

    CMMAD is a risk reduction effort for the AMDS program. As part of CMMAD, multiple instances of semi autonomous robotic mine detection systems were created. Each instance consists of a robotic vehicle equipped with sensors required for navigation and marking, countermine sensors and a number of integrated software packages which provide for real time processing of the countermine sensor data as well as integrated control of the robotic vehicle, the sensor actuator and the sensor. These systems were used to investigate critical interest functions (CIF) related to countermine robotic systems. To address the autonomy CIF, the INL developed RIK was extended to allow for interaction with a mine sensor processing code (MSPC). In limited field testing this system performed well in detecting, marking and avoiding both AT and AP mines. Based on the results of the CMMAD investigation we conclude that autonomous robotic mine detection is feasible. In addition, CMMAD contributed critical technical advances with regard to sensing, data processing and sensor manipulation, which will advance the performance of future fieldable systems. As a result, no substantial technical barriers exist which preclude - from an autonomous robotic perspective - the rapid development and deployment of fieldable systems.

  8. Semi autonomous mine detection system

    SciTech Connect

    Douglas Few; Roelof Versteeg; Herman Herman

    2010-04-01

    CMMAD is a risk reduction effort for the AMDS program. As part of CMMAD, multiple instances of semi autonomous robotic mine detection systems were created. Each instance consists of a robotic vehicle equipped with sensors required for navigation and marking, a countermine sensors and a number of integrated software packages which provide for real time processing of the countermine sensor data as well as integrated control of the robotic vehicle, the sensor actuator and the sensor. These systems were used to investigate critical interest functions (CIF) related to countermine robotic systems. To address the autonomy CIF, the INL developed RIK was extended to allow for interaction with a mine sensor processing code (MSPC). In limited field testing this system performed well in detecting, marking and avoiding both AT and AP mines. Based on the results of the CMMAD investigation we conclude that autonomous robotic mine detection is feasible. In addition, CMMAD contributed critical technical advances with regard to sensing, data processing and sensor manipulation, which will advance the performance of future fieldable systems. As a result, no substantial technical barriers exist which preclude – from an autonomous robotic perspective – the rapid development and deployment of fieldable systems.

  9. Semi-Autonomous Vehicle Project

    NASA Technical Reports Server (NTRS)

    Stewart, Christopher

    2016-01-01

    The primary objective this summer is "evaluating standards for wireless architecture for the internet of things". The Internet of Things is the network of physical objects or "things" embedded with electronics, software, sensors and network connectivity which enables these objects to collect and exchange data and make decisions based on said data. This was accomplished by creating a semi-autonomous vehicle that takes advantage of multiple sensors, cameras, and onboard computers and combined them with a mesh network which enabled communication across large distances with little to no interruption. The mesh network took advantage of what is known as DTN - Disruption Tolerant Networking which according to NASA is the new communications protocol that is "the first step towards interplanetary internet." The use of DTN comes from the fact that it will store information if an interruption in communications is detected and even forward that information via other relays within range so that the data is not lost. This translates well into the project because as the car moves further away from whatever is sending it commands (in this case a joystick), the information can still be forwarded to the car with little to no loss of information thanks to the mesh nodes around the driving area.

  10. Semi-Markov Unreliability Range Evaluator

    NASA Technical Reports Server (NTRS)

    Butler, Ricky W.; Boerschlein, David P.

    1993-01-01

    Semi-Markov Unreliability Range Evaluator, SURE, computer program is software tool for analysis of reconfigurable, fault-tolerant systems. Traditional reliability analyses based on aggregates of fault-handling and fault-occurrence models. SURE provides efficient means for calculating accurate upper and lower bounds for probabilities of death states for large class of semi-Markov mathematical models, and not merely those reduced to critical-pair architectures.

  11. Totally semi-continuous and semi totally-continuous functions in double fuzzy topological spaces

    NASA Astrophysics Data System (ADS)

    Mahmood Mohammed, Fatimah; Md Noorani, Mohd Salmi; Salleh, Abdul Razak

    2013-04-01

    The aim of this paper is to introduce new classes of functions called totally-continuous functions and its variants totally semi-continuous functions and semi totally-continuous functions in double fuzzy topological spaces. Their characterizations, examples and relationship with other notions of continuous functions in this space are provided.

  12. Exchange potentials for semi-classical electrons.

    PubMed

    Herzfeld, Judith; Ekesan, Solen

    2016-11-09

    Semi-classical electrons offer access to efficient and intuitive simulations of chemical reactions. As for any treatment of fermions, the greatest difficulty is in accounting for anti-symmetry effects. Semi-classical efforts to-date either reference Slater-determinants from ab initio treatments or adopt a heuristic approach inspired by density functional treatments. Here we revisit the problem with a combined approach. We conclude that semi-classical electrons need to reference a non-conventional wave function and find that (1) contrary to earlier suppositions, contributions from the electrostatic terms in the Hamiltonian are of similar magnitude to those from the kinetic terms and (2) the former point to a need to supplement pair potentials with 3-body potentials. The first result explains features of reported heuristic potentials, and the second provides a firm footing for extending the transferability of potentials across a wider range of elements and bonding scenarios.

  13. Tough, processable simultaneous semi-interpenetrating polyimides

    NASA Technical Reports Server (NTRS)

    Pater, Ruth H. (Inventor)

    1996-01-01

    A high temperature semi-interpenetrating polymer network (semi-IPN) was developed which had significantly improved processability, damage tolerance and mechanical performance, when compared to the commercial Thermid.RTM. materials. This simultaneous semi-IPN was prepared by mixing a thermosetting polyimide with a thermoplastic monomer precursor solution (NR-15082) and allowing them to react upon heating. This reaction occurs at a rate which decreases the flow and broadens the processing window. Upon heating at a higher temperature, there is an increase in flow. Because of the improved flow properties, broadened processing window and enhanced toughness, high strength polymer matrix composites, adhesives and molded articles can now be prepared from the acetylene endcapped polyimides which were previously inherently brittle and difficult to process.

  14. Semi-infinite cohomology and string theory

    PubMed Central

    Frenkel, I. B.; Garland, H.; Zuckerman, G. J.

    1986-01-01

    We develop the theory of semi-infinite cohomology of graded Lie algebras first introduced by Feigin. We show that the relative semi-infinite cohomology has a structure analogous to that of the de Rham cohomology in Kähler geometry. We prove a vanishing theorem for a special class of modules, and we apply our results to the case of the Virasoro algebra and the Fock module. In this case the zero cohomology is identified as the physical subspace of the Fock module and the no-ghost theorem follows. We reveal the profound relation of semi-infinite cohomology theory to the gauge-invariant free string theory constructed by Banks and Peskin. We then indicate the connection between gauge-invariant interacting string theories and the geometric realizations of the infinite-dimensional Lie algebras. PMID:16578792

  15. Thermal Conductivity Investigation of {Ca}_{9} {RE}({VO}_{4})_{7} (RE = La, Nd, Gd) and {Ca}_{10}M(VO_{4})_{7} (M = Li, Na, K) Single Crystals

    NASA Astrophysics Data System (ADS)

    Popov, P. A.; Skrobov, S. A.; Matovnikov, A. V.; Kosmyna, M. B.; Puzikov, V. M.; Nazarenko, B. P.; Shekhovtsov, A. N.; Behrooz, A.; Paszkowicz, W.; Khodasevich, I. A.; Shereshovets, N. N.; Voitikov, S. V.; Orlovich, V. A.

    2017-01-01

    The {Ca}9{RE}({VO}4)7 (RE = La, Nd, Gd) and {Ca}_{10}{M}({VO}4)7 (M = Li, Na, K) single crystals have been grown by the Czochralski method. The binary vanadates are isostructural to "whitlockite" mineral (rhombohedral symmetry, R3 c space group). Their thermal conductivity has been investigated in the range 50 K-300 K parallel to the c axis. For {Ca}9{Gd}({VO}4)7 crystals, the thermal conductivity has been investigated in the range 300 K-550 K also. Additionally, for the {Ca}_{10}{M}({VO}4)7 (M = Li, Na, K) crystals the heat capacity has been studied in the temperature range 80 K-300 K. The character of the temperature dependence of thermal conductivity is close to that of glasses. The possible reasons of the observed features of the thermal conductivity have been analyzed. Raman spectra of {Ca}_{10}{M}({VO}4)7 (M = Li, Na, K) crystals have been measured and discussed. The spectral lines were broad and similar to polycrystalline or amorphous solids. These crystals are expected to be suitable for application as efficient nonlinear optic and laser materials.

  16. Multiple gamma lines from semi-annihilation

    SciTech Connect

    D'Eramo, Francesco; McCullough, Matthew; Thaler, Jesse E-mail: mccull@mit.edu

    2013-04-01

    Hints in the Fermi data for a 130 GeV gamma line from the galactic center have ignited interest in potential gamma line signatures of dark matter. Explanations of this line based on dark matter annihilation face a parametric tension since they often rely on large enhancements of loop-suppressed cross sections. In this paper, we pursue an alternative possibility that dark matter gamma lines could arise from ''semi-annihilation'' among multiple dark sector states. The semi-annihilation reaction ψ{sub i}ψ{sub j} → ψ{sub k}γ with a single final state photon is typically enhanced relative to ordinary annihilation ψ{sub i}ψ-bar {sub i} → γγ into photon pairs. Semi-annihilation allows for a wide range of dark matter masses compared to the fixed mass value required by annihilation, opening the possibility to explain potential dark matter signatures at higher energies. The most striking prediction of semi-annihilation is the presence of multiple gamma lines, with as many as order N{sup 3} lines possible for N dark sector states, allowing for dark sector spectroscopy. A smoking gun signature arises in the simplest case of degenerate dark matter, where a strong semi-annihilation line at 130 GeV would be accompanied by a weaker annihilation line at 173 GeV. As a proof of principle, we construct two explicit models of dark matter semi-annihilation, one based on non-Abelian vector dark matter and the other based on retrofitting Rayleigh dark matter.

  17. Semi-Markov Unreliability Range Evaluator (SURE)

    NASA Technical Reports Server (NTRS)

    Butler, R. W.

    1989-01-01

    Analysis tool for reconfigurable, fault-tolerant systems, SURE provides efficient way to calculate accurate upper and lower bounds for death state probabilities for large class of semi-Markov models. Calculated bounds close enough for use in reliability studies of ultrareliable computer systems. Written in PASCAL for interactive execution and runs on DEC VAX computer under VMS.

  18. A Semi-Annotated Bibliography: The Wabanakis.

    ERIC Educational Resources Information Center

    Braber, Lee; Dean, Jacquelyn M.

    A companion to the booklet, "A Teacher Manual on Native Americans: The Wabanakis," the semi-annotated bibliography consisting of 235 citations may be used by people who wish to have access to information and research (1890-1982) done about the tribes on the New England and Maritime shores, including the Wabanaki Confederacy composed of…

  19. Semi-automated identification of leopard frogs

    USGS Publications Warehouse

    Petrovska-Delacrétaz, Dijana; Edwards, Aaron; Chiasson, John; Chollet, Gérard; Pilliod, David S.

    2014-01-01

    Principal component analysis is used to implement a semi-automatic recognition system to identify recaptured northern leopard frogs (Lithobates pipiens). Results of both open set and closed set experiments are given. The presented algorithm is shown to provide accurate identification of 209 individual leopard frogs from a total set of 1386 images.

  20. A Semi-Automatic Variability Search

    NASA Astrophysics Data System (ADS)

    Maciejewski, G.; Niedzielski, A.

    Technical features of the Semi-Automatic Variability Search (SAVS) operating at the Astronomical Observatory of the Nicolaus Copernicus University and the results of the first year of observations are presented. The user-friendly software developed for reduction of acquired CCD images and detection of new variable stars is also described.

  1. Calculation of the temperature in the container unit with a modified design for the production of 99Mo at the VVR-Ts research reactor facility (IVV.10M)

    NASA Astrophysics Data System (ADS)

    Kazantsev, A. A.; Sergeev, V. V.; Kochnov, O. Yu.

    2015-12-01

    The temperature regime is calculated for two different designs of containers with uranium-bearing material for the upgraded VVR-Ts research reactor facility (IVV.10M). The containers are to be used in the production of 99Mo. It is demonstrated that the modification of the container design leads to a considerable temperature reduction and an increase in the near-wall boiling margin and allows one to raise the amount of material loaded into the container. The calculations were conducted using the international thermohydraulic contour code TRAC intended to analyze the technical safety of water-cooled nuclear power units.

  2. Monitoring Cyp2b10 mRNA expression at cessation of 2-year carcinogenesis bioassay in mouse liver provides evidence for a carcinogenic mechanism devoid of human relevance: The dalcetrapib experience

    SciTech Connect

    Hoflack, J-C.; Mueller, L. Fowler, S.; Braendli-Baiocco, A.; Flint, N.; Kuhlmann, O.; Singer, T.; Roth, A.

    2012-03-15

    Introduction: Dalcetrapib is a cholesteryl ester transfer protein (CETP) modulator in clinical assessment for cardiovascular outcome benefits. In compliance with regulatory requirements, dalcetrapib was evaluated in rodent 2-year carcinogenesis bioassays. In the mouse bioassay, male mice demonstrated increased liver weight and statistically increased incidences of hepatocellular adenoma/carcinoma. Hepatic cytochrome p450 (Cyp) 2b10 mRNA induction and increased Cyp2b10 enzyme activity signify activation of hepatic nuclear receptor constitutive androstane receptor (CAR), a widely established promoter of rodent-specific hepatic tumors. We therefore monitored hepatic Cyp2b10 mRNA and its enzyme activity in a subset of dalcetrapib-treated male mice from the bioassay. Methods: Liver samples were obtained from ∼ 1/3 of male mice from each dose group including vehicle-controls (mean and earliest study day of death 678 and 459 respectively). Quantitative real time PCR (qRT-PCR) was performed to determine Cyp2b10 mRNA expression and Cyp1a-, Cyp2b10- and Cyp3a-selective activities were monitored. Results: Cyp2b10 mRNA was strongly induced by dalcetrapib with an expected wide inter-individual variation (5–1421-fold). Group average fold-induction versus vehicle-controls showed a dose-related increase from 48-fold (250 mg/kg/day) to 160-fold (750 mg/kg/day), which declined slightly at 2000 mg/kg/day (97-fold). Cyp enzyme activities showed approximate doubling of total Cyp P450 content per milligram protein and a 9-fold increase in Cyp2b10-selective pentoxyresorufin O-dealkylase activity (750 mg/kg/day). Discussion: These data from hepatic Cyp2b10 monitoring are strongly suggestive of CAR activation by dalcetrapib, a mechanism devoid of relevance towards hepatocarcinogenesis in humans; results show feasibility of Cyp2b10 as a surrogate marker for this mechanism at cessation of a carcinogenesis bioassay. -- Highlights: ► Liver tumors were induced in male mice by dalcetrapib

  3. Calculation of the temperature in the container unit with a modified design for the production of {sup 99}Mo at the VVR-Ts research reactor facility (IVV.10M)

    SciTech Connect

    Kazantsev, A. A.; Sergeev, V. V.; Kochnov, O. Yu.

    2015-12-15

    The temperature regime is calculated for two different designs of containers with uranium-bearing material for the upgraded VVR-Ts research reactor facility (IVV.10M). The containers are to be used in the production of {sup 99}Mo. It is demonstrated that the modification of the container design leads to a considerable temperature reduction and an increase in the near-wall boiling margin and allows one to raise the amount of material loaded into the container. The calculations were conducted using the international thermohydraulic contour code TRAC intended to analyze the technical safety of water-cooled nuclear power units.

  4. Nonlinear dual-axis biodynamic response of the semi-supine human body during vertical whole-body vibration

    NASA Astrophysics Data System (ADS)

    Huang, Ya; Griffin, Michael J.

    2008-04-01

    Nonlinear biodynamic responses are evident in many studies of the apparent masses of sitting and standing subjects in static postures that require muscle activity for postural control. In the present study, 12 male subjects adopted a relaxed semi-supine posture assumed to involve less muscle activity than during static sitting and standing. The supine subjects were exposed to two types of vertical vibration (in the x-axis of the semi-supine body): (i) continuous random vibration (0.25-20 Hz) at five magnitudes (0.125, 0.25, 0.5, 0.75, and 1.0 m s -2 rms); (ii) intermittent random vibration (0.25-20 Hz) alternately at 0.25 and 1.0 m s -2 rms. With continuous random vibration, the dominant primary resonance frequency in the median normalised apparent mass decreased from 10.35 to 7.32 Hz as the vibration magnitude increased from 0.125 to 1.0 m s -2 rms. This nonlinear response was apparent in both the vertical ( x-axis) apparent mass and in the horizontal ( z-axis) cross-axis apparent mass. As the vibration magnitude increased from 0.25 to 1.0 m s -2 rms, the median resonance frequency of the apparent mass with intermittent random vibration decreased from 9.28 to 8.06 Hz whereas, over the same range of magnitudes with continuous random vibration, the resonance frequency decreased from 9.62 to 7.81 Hz. The median change in the resonance frequency (between 0.25 and 1.0 m s -2 rms) was 1.37 Hz with the intermittent random vibration and 1.71 with the continuous random vibration. With the intermittent vibration, the resonance frequency was higher at the high magnitude and lower at the low magnitude than with continuous vibration of the same magnitudes. The response was typical of thixotropy that may be a primary cause of the nonlinear biodynamic responses to whole-body vibration.

  5. Optimal semi-active vibration absorber for harmonic excitation based on controlled semi-active damper

    NASA Astrophysics Data System (ADS)

    Weber, F.

    2014-09-01

    The semi-active vibration absorber (SVA) based on controlled semi-active damper is formulated to realize the behaviour of the passive undamped vibration absorber tuned to the actual harmonic disturbing frequency. It is shown that the controlled stiffness force, which is emulated by the semi-active damper to realize the precise real-time frequency tuning of the SVA, is unpreventably combined with the generation of undesirable damping in the semi-active damper whereby the SVA does not behave as targeted. The semi-active stiffness force is therefore optimized for minimum primary structure response. The results point out that the optimal semi-active stiffness force reduces the undesirable energy dissipation in the SVA at the expenses of slight imprecise frequency tuning. Based on these findings, a real-time applicable suboptimal SVA is formulated that also takes the relative motion constraint of real mass dampers into account. The results demonstrate that the performance of the suboptimal SVA is closer to that of the active solution than that of the passive mass damper.

  6. Spatial variation, mapping, and classification of moss families in semi-arid landscapes in NW Turkey.

    PubMed

    Abay, Gökhan; Gül, Ebru; Günlü, Alkan; Erşahin, Sabit; Ursavaş, Serhat

    2015-03-01

    Geostatistics and remote sensing techniques are frequently used in analyzing the spatial variability of terrestrial ecosystems. We analyzed spatial variation of moss families by geostatistics and Landsat imagery in a typical semi-arid landscape in North Central Anatolia, Turkey. We sampled 49 sites, chosen based on elevation, slope steepness, and slope aspect. Moss families were determined in a 10-m(2) representative area at each sampling site. The samples were transported to a laboratory and identified for moss families. In total, 10 families were found. Semivariogram analysis was performed to analyze the spatial structure of these families. The semivariogram analysis showed that the moss families were spatially dependent within 117 m in the study area. Thirteen thematic classes were categorized by Landsat Thematic Mapper (TM) image in the study area. The classification resulted in an overall kappa statistic of 0.8535, producer accuracy of 74.29, and user accuracy of 86.67. The family with the lowest classification accuracy was Orthotrichaceae (kappa of 0.6379, producer accuracy of 64.52, and user accuracy of 66.67). The moss families and the other classes were identified with a 0.78 kappa statistic value and an 80.74 % accuracy level by using the Landsat TM. The classification showed that Brachytheciaceae, Pottiaceae, Bryaceae, and Grimmiaceae were the most abundant moss families in this semi-arid environment.

  7. Semi-supervised Discriminative Structured Prediction

    DTIC Science & Technology

    2013-10-30

    xi) and γ is a trade-off parameter that controls the influence of the unlabeled data. The minimum entropy and variance semi-supervised boosting methods...optimizing the ranking measure which represents the agreement between the permutation by relevance judgments and the ranking yielded by a ranking function...for the permutation , and maximize the likelihood of top-m ranked documents. This iterative procedure is continued until convergence. We conduct

  8. Princeton VLSI Project: Semi-Annual Report.

    DTIC Science & Technology

    1982-11-01

    A’D-A149 588 PRINCETON VLSI PROJECT: SEMI-ANNUAL REPORT(U) PRINCETON i/i UNIV NJ DEPT OF ELECTRICAL ENGINEERING AND COMPUTER SCIENCE R J LIPTON 91...logic. We plan further experiments to further vali- date these results. Finally, we have also found a way to transform any combinational logic cir...Programming Richard J. Lptoi4 Sftp3 , C Nerth - Robert 5edgeutck Jacobo Vaides tDepartment of Electrical Engineering and Computer Science Princeton

  9. Semi-classical methods in nuclear physics

    NASA Astrophysics Data System (ADS)

    Brink, David M.

    These lecture notes present an introduction to some semi-classical techniques which have applications in nuclear physics. Topics discussed include the WKB method, approaches based on the Feynman path integral, the Gutzwiller trace formula for level density fluctuations and the Thomas-Fermi approximation and the Vlasov equation for many-body problems. There are applications to heavy ion fusion reactions, bremsstrahlung emission in alpha decay and nuclear response functions.

  10. Semi-Global Matching in Object Space

    NASA Astrophysics Data System (ADS)

    Bethmann, F.; Luhmann, T.

    2015-03-01

    Semi-Global Matching (SGM) is a widespread algorithm for image matching which is used for very different applications, ranging from real-time applications (e.g. for generating 3D data for driver assistance systems) to aerial image matching. Originally developed for stereo-image matching, several extensions have been proposed to use more than two images within the matching process (multi-baseline matching, multi-view stereo). These extensions still perform the image matching in (rectified) stereo images and combine the pairwise results afterwards to create the final solution. This paper proposes an alternative approach which is suitable for the introduction of an arbitrary number of images into the matching process and utilizes image matching by using non-rectified images. The new method differs from the original SGM method mainly in two aspects: Firstly, the cost calculation is formulated in object space within a dense voxel raster by using the grey (or colour) values of all images instead of pairwise cost calculation in image space. Secondly, the semi-global (path-wise) minimization process is transferred into object space as well, so that the result of semi-global optimization leads to index maps (instead of disparity maps) which directly indicate the 3D positions of the best matches. Altogether, this yields to an essential simplification of the matching process compared to multi-view stereo (MVS) approaches. After a description of the new method, results achieved from two different datasets (close-range and aerial) are presented and discussed.

  11. Semi-automatic Segmentation for Prostate Interventions

    PubMed Central

    Mahdavi, S. Sara; Chng, Nick; Spadinger, Ingrid; Morris, William J.; Salcudean, Septimiu E.

    2011-01-01

    In this paper we report and characterize a semi-automatic prostate segmentation method for prostate brachytherapy. Based on anatomical evidence and requirements of the treatment procedure, a warped and tapered ellipsoid was found suitable as the a priori 3D shape of the prostate. By transforming the acquired endorectal transverse images of the prostate into ellipses, the shape fitting problem was cast into a convex problem which can be solved efficiently. The average whole gland error between volumes created from manual and semi-automatic contours from 21 patients was 6.63±0.9%. For use in brachytherapy treatment planning, the resulting contours were modified, if deemed necessary, by radiation oncologists prior to treatment. The average whole gland volume error between the volumes computed from semi-automatic contours and those computed from modified contours, from 40 patients, was 5.82±4.15%. The amount of bias in the physicians’ delineations when given an initial semi-automatic contour was measured by comparing the volume error between 10 prostate volumes computed from manual contours with those of modified contours. This error was found to be 7.25±0.39% for the whole gland. Automatic contouring reduced subjectivity, as evidenced by a decrease in segmentation inter- and intra-observer variability from 4.65% and 5.95% for manual segmentation to 3.04% and 3.48% for semi-automatic segmentation, respectively. We characterized the performance of the method relative to the reference obtained from manual segmentation by using a novel approach that divides the prostate region into nine sectors. We analyzed each sector independently as the requirements for segmentation accuracy depend on which region of the prostate is considered. The measured segmentation time is 14±1 seconds with an additional 32±14 seconds for initialization. By assuming 1–3 minutes for modification of the contours, if necessary, a total segmentation time of less than 4 minutes is required

  12. Groundwater and unsaturated zone evaporation and transpiration in a semi-arid open woodland

    NASA Astrophysics Data System (ADS)

    Balugani, E.; Lubczynski, M. W.; Reyes-Acosta, L.; van der Tol, C.; Francés, A. P.; Metselaar, K.

    2017-04-01

    Studies on evapotranspiration partitioning under eddy covariance (EC) towers rarely address the separate effects of transpiration and evaporation on groundwater resources. Such partitioning is important to accurately assess groundwater resources, especially in arid and semi-arid areas. The main objective of this study was to partition (evaluate separately) the evaporation and transpiration components of evapotranspiration, originated either from saturated or unsaturated zone, and estimate their contributions in a semi-arid area characterized by relatively shallow groundwater Table (0-10 m deep). Evapotranspiration, tree transpiration and subsurface evaporation were estimated with EC tower, using sap flow methods and HYDRUS1D model, respectively. To set up the HYDRUS1D model, soil material properties, soil moisture, soil temperature, soil matric potential and water table depth were measured in the area. The tree transpiration was sourced into groundwater and unsaturated zone components (∼0.017 mm d-1 for both) and accounted for only ∼6% of the evapotranspiration measured by the EC tower (∼0.565 mm d-1), due to the low canopy coverage in the study area (7%). The subsurface evaporation fluxes were also sourced into groundwater and unsaturated zone components using the SOURCE package, and their relative relevance in total evapotranspiration was assessed. Subsurface evaporation was the main flux year-round (∼0.526 mm d-1). During late autumn, winter and early spring time, the unsaturated zone evaporation was dominant, while in dry summer the relevance of groundwater evaporation increased, reaching one third of evapotranspiration, although errors in the water balance closure point still at its possible underestimation. The results show that, in arid and semi-arid areas with sparse vegetation, the often neglected groundwater evaporation is a relevant contribution to evapotranspiration, and that water vapor flow should be taken into account in the calculation of

  13. Analysis of electrochemical noise (ECN) data in time and frequency domain for comparison corrosion inhibition of some azole compounds on Cu in 1.0 M H2SO4 solution

    NASA Astrophysics Data System (ADS)

    Ramezanzadeh, B.; Arman, S. Y.; Mehdipour, M.; Markhali, B. P.

    2014-01-01

    In this study, the corrosion inhibition properties of two similar heterocyclic compounds namely benzotriazole (BTA) and benzothiazole (BNS) inhibitors on copper in 1.0 M H2SO4 solution were studied by electrochemical techniques as well as surface analysis. The results showed that corrosion inhibition of copper largely depends on the molecular structure and concentration of the inhibitors. The effect of DC trend on the interpretation of electrochemical noise (ECN) results in time domain was evaluated by moving average removal (MAR) method. Accordingly, the impact of square and Hanning window functions as drift removal methods in frequency domain was studied. After DC trend removal, a good trend was observed between electrochemical noise (ECN) data and the results obtained from EIS and potentiodynamic polarization. Furthermore, the shot noise theory in frequency domain was applied to approach the charge of each electrochemical event (q) from the potential and current noise signals.

  14. Semi-Lagrangian modelling of tropospheric ozone

    NASA Astrophysics Data System (ADS)

    Pudykiewicz, Janusz A.; Kallaur, A.; Smolarkiewicz, Piotr K.

    1997-07-01

    The occurrence of high concentrations of ozone in the lower part of the troposphere is considered as one of the most important issues of tropospheric chemistry. The chemical mechanisms of tropospheric ozone formation are complex, and highly variable meteorological conditions contribute additionally to difficulties in an accurate prediction of ozone episodes. An effective way to increase our understanding of the problem and eventually improve our ability to predict the concentration of tropospheric ozone and to formulate emission control strategies is by applying a comprehensive model representing accurately the interaction between meteorological processes and chemical reactions. This paper presents a 3-dimensional semi-Lagrangian, chemical tracer model (CTM) featuring an accurate transport algorithm, comprehensive oxidants chemistry and deposition modules. The CTM is executed in off line mode with a semi-Lagrangian, nonhydrostatic, mesoscale meteorological model that contains an extensive parameterization of physical processes (including a boundary layer scheme and clouds). The system of models was run for a time period of 6days in order to generate a tropospheric ozone field during a smog episode observed in the eastern part of North America, in the beginning of August 1988. The numerical simulation was performed on grids with resolution of 20 and 40km with 25 vertical levels. The emissions inventory considered in the simulation included point sources, surface biogenic sources, surface mobile sources and surface non-mobile sources. An evaluation of the model results against observations clearly indicates the ability of the system to simulate regional aspects of a tropospheric ozone episode. The model performance compares well to other models' results reported in the literature. An important achievement of this work is improving the physical realism of simulations by using highly accurate, nonoscillatory semi-Lagrangian advection transport algorithms.

  15. Semi-transparent inverted organic solar cells

    NASA Astrophysics Data System (ADS)

    Schmidt, H.; Winkler, T.; Tilgner, M.; Flügge, H.; Schmale, S.; Bülow, T.; Meyer, J.; Johannes, H.-H.; Riedl, T.; Kowalsky, W.

    2009-08-01

    We will present efficient semi-transparent bulk-heterojunction [regioregular of poly(3-hexylthiophene): (6,6)-phenyl C61 butyric acid methyl ester] solar cells with an inverted device architecture. Highly transparent ZnO and TiO2 films prepared by Atomic Layer Deposition are used as cathode interlayers on top of ITO. The topanode consists of a RF-sputtered ITO layer. To avoid damage due to the plasma deposition of this layer, a sputtering buffer layer of MoO3 is used as protection. This concept allows for devices with a transmissivity higher than 60 % for wavelengths 650 nm. The thickness of the MoO3 buffer has been varied in order to study its effect on the electrical properties of the solar cell and its ability to prevent possible damage to the organic active layers upon ITO deposition. Without this buffer or for thin buffers it has been found that device performance is very poor concerning the leakage current, the fill factor, the short circuit current and the power conversion efficiencies. As a reference inverted solar cells with a metal electrode (Al) instead of the ITO-top contact are used. The variation between the PCE of top versus conventional illumination of the semi-transparent cells was also examined and will be interpreted in view of the results of the optical simulation of the dielectric device stack with and without reflection top electrode. Power conversion efficiencies of 2-3 % for the opaque inverted solar cells and 1.5-2.5 % for the semi-transparent devices were obtained under an AM1.5G illumination.

  16. Automated semi-spherical irradiance meter

    NASA Astrophysics Data System (ADS)

    Tecpoyotl-Torres, M.; Vera-Dimas, J. G.; Escobedo-Alatorre, J.; Cabello-Ruiz, R.; Varona, J.

    2011-09-01

    In this semi-spherical meter, a single detector is used to realize all measurements, which is located on the extreme of a rectangular ring (assumed as joined two mobile branches in order to compensate the weights), describing half-meridians from 0° up to 170°. The illumination source under test is located at the center of the mobile support, which can rotate 360° horizontally. The two combined movements allow us to obtain a semi-spherical geometry. The number of measurement points is determined by the two step-motors located under the mobile support of the luminary and on one of the two fixed arms, which support the mobile rectangular ring, respectively. The mechanical arrangement has the enough rigidity to support the precision required for the acquisition stage, based on a dsPIC. The main advantages of this arrange are: Its low costs (using recyclable materials only such as "electronic waste"), a reliable detection based on a single photo-detector, with an integrated amplification stage, and the mechanical design. The received power by the detector is useful to obtain the irradiance profile of the lighting sources under test. The semi-spherical geometry of the meter makes it useful for the analysis of directive and non directive sources, in accordance with the angle described by the mobile ring. In this work, special attention is given to LED lamps due to its impact in several sceneries of the daily life. A comparison between the irradiance patterns of two LED lamps is also given.

  17. Solar Energy Monitor In Space (SEMIS)

    NASA Technical Reports Server (NTRS)

    Thekaekara, M. P.

    1974-01-01

    Measurements made at high altitudes from aircraft have resulted in the establishment of standard values of the solar constant and extraterrestrial solar spectral irradiance. These standard values and other solar spectral curves are described. The problem of possible variations of the solar constant and solar spectrum and their influence on the earth-atmosphere system and weather related phenomena is examined. It is shown that the solar energy input parameters should be determined with considerably greater accuracy and precision than has been possible. An instrument package designed as a compact, low weight solar energy monitor in space (SEMIS) is described.

  18. Global semi-arid climate change over last 60 years

    NASA Astrophysics Data System (ADS)

    Huang, Jianping; Ji, Mingxia; Xie, Yongkun; Wang, Shanshan; He, Yongli; Ran, Jinjiang

    2016-02-01

    This study analyzes areal changes and regional climate variations in global semi-arid regions over 61 years (1948-2008) and investigates the dynamics of global semi-arid climate change. The results reveal that the largest expansion of drylands has occurred in semi-arid regions since the early 1960s. This expansion of semi-arid regions accounts for more than half of the total dryland expansion. The area of semi-arid regions in the most recent 15 years studied (1990-2004) is 7 % larger than that during the first 15 years (1948-1962) of the study period; this expansion totaled 0.4 × 106 and 1.2 × 106 km2 within the American continents and in the Eastern Hemisphere, respectively. Although semi-arid expansion occurred in both regions, the shifting patterns of the expansion are different. Across the American continents, the newly formed semi-arid regions developed from arid regions, in which the climate became wetter. Conversely, in the continental Eastern Hemisphere, semi-arid regions replaced sub-humid/humid regions, in which the climate became drier. The climate change in drying semi-arid regions over East Asia is primarily dominated by a weakened East Asian summer monsoon, while the wetting of semi-arid regions over North America is primarily controlled by enhanced westerlies.

  19. Global semi-arid climate change over last 60 years

    NASA Astrophysics Data System (ADS)

    Ji, Mingxia; Huang, Jianping

    2016-04-01

    This study analyzes areal changes and regional climate variations in global semi-arid regions over 61 years (1948-2008) and investigates the dynamics of global semi- arid climate change. The results reveal that the largest expansion of drylands has occurred in semi-arid regions since the early 1960s. This expansion of semi-arid regions accounts for more than half of the total dryland expansion. The area of semi-arid regions in the most recent 15 years studied (1990-2004) is 7 % larger than that during the first 15 years (1948-1962) of the study period; this expansion totaled 0.4×106 and 1.2×106 km2 within the American continents and in the Eastern Hemisphere, respectively. Although semi-arid expansion occurred in both regions, the shifting patterns of the expansion are different. Across the American continents, the newly formed semi-arid regions developed from arid regions, in which the climate became wetter. Conversely, in the continental Eastern Hemisphere, semi-arid regions replaced sub-humid/humid regions, in which the climate became drier. The climate change in drying semi-arid regions over East Asia is primarily dominated by a weakened East Asian summer monsoon, while the wetting of semi-arid regions over North America is primarily controlled by enhanced westerlies.

  20. Note on the semi-annual effect in the thermosphere

    NASA Technical Reports Server (NTRS)

    Volland, H.; Mayr, H. G.

    1972-01-01

    The semi-annual variation in the thermospheric density is discussed in terms of the spatial and temporal variations in the solar heat input. Two heat sources are considered: the solar heat input associated with the semi-annual migration of the sun, and the auroral heat associated with the semi-annual component in magnetic storms. It is shown that the relatively large global component in the semi-annual effect of the total mass density can be explained by the lack of advective loss which otherwise damps the latitude dependent components in the annual and semi-annual variations, and the significant latitude dependence in the semi-annual variations of composition and temperature can be tied to the diffusion process which is induced by the thermospheric circulation.

  1. An Unconditionally Stable Fully Conservative Semi-Lagrangian Method (PREPRINT)

    DTIC Science & Technology

    2010-08-07

    An Unconditionally Stable Fully Conservative Semi- Lagrangian Method Michael Lentine∗, Jón Tómas Grétarsson∗, Ronald Fedkiw∗ Stanford University...353 Serra Mall Room 207, Stanford, CA 94305 Abstract Semi- Lagrangian methods have been around for some time, dating back at least to [3]. Researchers...the typical semi- Lagrangian interpolation step in order to guarantee that the amount of the con- servative quantity does not increase during this

  2. Semi-Empirical Modeling of SLD Physics

    NASA Technical Reports Server (NTRS)

    Wright, William B.; Potapczuk, Mark G.

    2004-01-01

    The effects of supercooled large droplets (SLD) in icing have been an area of much interest in recent years. As part of this effort, the assumptions used for ice accretion software have been reviewed. A literature search was performed to determine advances from other areas of research that could be readily incorporated. Experimental data in the SLD regime was also analyzed. A semi-empirical computational model is presented which incorporates first order physical effects of large droplet phenomena into icing software. This model has been added to the LEWICE software. Comparisons are then made to SLD experimental data that has been collected to date. Results will be presented for the comparison of water collection efficiency, ice shape and ice mass.

  3. Phase Transitions with Semi-Diffuse Interfaces

    SciTech Connect

    Greenberg, James M.

    2003-07-16

    In this paper we examine new ''phase-field'' models with semi-diffuse interfaces. These models have the property that the -1/+1 planar phase transitions take place over a finite interval. The models also support multiple interface solutions with interfaces centered at arbitrary points L{sub 1} < L{sub 2} < ... < L{sub N}. These solutions correspond to local minima of an entropy functional rather than saddle points and are dynamically stable. The classical models have no such exact solutions but they do support solutions with N equally spaced transition points where the order parameter transitions between valves p{sub min}(N) and p{sub max}(N) satisfying -1 < p{sub min}(N) < 0 < p{sub max} (N) < 1. These solutions of the classical model are saddle points of the entropy functional associated with those models and are not dynamically stable.

  4. Determine the optimum spectral reflectance of juniper and pistachio in arid and semi-arid region

    NASA Astrophysics Data System (ADS)

    Fadaei, Hadi; Suzuki, Rikie

    2012-11-01

    Arid and semi-arid areas of northeast Iran cover about 3.4 million ha are populated by two main tree species, the broadleaf Pistacia vera. L (pistachio) and the conifer Juniperus excelsa ssp. polycarpos (Persian juniper). Natural stands of pistachio in Iran are not only environmentally important but genetically essential as seed sources for pistachio production in orchards. In this study, we estimated the optimum spectral reflectance of juniper forests and natural pistachio stands using remote sensing to help in the sustainable management and production of pistachio in Iran. In this research spectral reflectance are able to specify of multispectral from Advanced Land Observing Satellite (ALOS) that provided by JAXA. These data included PRISM is a panchromatic radiometer with a 2.5 m spatial resolution at nadir, has one band with a wavelength of 0.52-0.77 μm and AVNIR-2 is a visible and near infrared radiometer for observing land and coastal zones with a 10 m spatial resolution at nadir, has four multispectral bands: blue (0.42-0.50 μm), green (0.52-0.60 μm), red (0.61-0.69 μm), and near infrared (0.76-0.89 μm). Total ratio vegetation index (TRVI) of optimum spectral reflectance of juniper and pistachio have been evaluated. The result of TRVI for Pistachio and juniper were (R2= 0.71 and 0.55). I hope this research can provide decision of managers to helping sustainable management for arid and semi-arid regions in Iran.

  5. Semi-automated calibration method for modelling of mountain permafrost evolution in Switzerland

    NASA Astrophysics Data System (ADS)

    Marmy, Antoine; Rajczak, Jan; Delaloye, Reynald; Hilbich, Christin; Hoelzle, Martin; Kotlarski, Sven; Lambiel, Christophe; Noetzli, Jeannette; Phillips, Marcia; Salzmann, Nadine; Staub, Benno; Hauck, Christian

    2016-11-01

    Permafrost is a widespread phenomenon in mountainous regions of the world such as the European Alps. Many important topics such as the future evolution of permafrost related to climate change and the detection of permafrost related to potential natural hazards sites are of major concern to our society. Numerical permafrost models are the only tools which allow for the projection of the future evolution of permafrost. Due to the complexity of the processes involved and the heterogeneity of Alpine terrain, models must be carefully calibrated, and results should be compared with observations at the site (borehole) scale. However, for large-scale applications, a site-specific model calibration for a multitude of grid points would be very time-consuming. To tackle this issue, this study presents a semi-automated calibration method using the Generalized Likelihood Uncertainty Estimation (GLUE) as implemented in a 1-D soil model (CoupModel) and applies it to six permafrost sites in the Swiss Alps. We show that this semi-automated calibration method is able to accurately reproduce the main thermal condition characteristics with some limitations at sites with unique conditions such as 3-D air or water circulation, which have to be calibrated manually. The calibration obtained was used for global and regional climate model (GCM/RCM)-based long-term climate projections under the A1B climate scenario (EU-ENSEMBLES project) specifically downscaled at each borehole site. The projection shows general permafrost degradation with thawing at 10 m, even partially reaching 20 m depth by the end of the century, but with different timing among the sites and with partly considerable uncertainties due to the spread of the applied climatic forcing.

  6. An evaluation of acoustic seabed classification techniques for marine biotope monitoring over broad-scales (>1 km 2) and meso-scales (10 m 2-1 km 2)

    NASA Astrophysics Data System (ADS)

    van Rein, H.; Brown, C. J.; Quinn, R.; Breen, J.; Schoeman, D.

    2011-07-01

    Acoustic seabed classification is a useful tool for monitoring marine benthic habitats over broad-scales (>1 km 2) and meso-scales (10 m 2-1 km 2). Its utility in this context was evaluated using two approaches: by describing natural changes in the temporal distribution of marine biotopes across the broad-scale (4 km 2), and by attempting to detect specific experimentally-induced changes to kelp-dominated biotopes across the meso-scale (100 m 2). For the first approach, acoustic backscatter mosaics were constructed using sidescan sonar and multibeam echosounder data collected from Church Bay (Rathlin Island, Northern Ireland) in 1999, 2008 and 2009. The mosaics were manually segmented into acoustic facies, which were ground-truthed using a drop-video camera. Biotopes were classified from the video by multivariate exploratory analysis and cross-tabulated with the acoustic facies, showing a positive correlation. These results were integrated with bathymetric data to map the distribution of seven unique biotopes in Church Bay. Kappa analysis showed the biotope distribution was highly similar between the biotope maps, possibly due to the stability of bedforms shaped by the tidal regime around Rathlin Island. The greatest biotope change in this approach was represented by seasonal and annual changes in the growth of the seagrass, Zostera marina. In the second approach, sidescan sonar data were collected before and after the removal of 100 m 2 of kelp from three sites. Comparison of the data revealed no differences between the high-resolution backscatter imagery. It is concluded that acoustic seabed classification can be used to monitor change over broad- and meso-scales but not necessarily for all biotopes; its success depends on the type of acoustic system employed and the biological characteristics of the target biotope.

  7. Semi-classical analysis and pseudo-spectra

    NASA Astrophysics Data System (ADS)

    Davies, E. B.

    We prove an approximate spectral theorem for non-self-adjoint operators and investigate its applications to second-order differential operators in the semi-classical limit. This leads to the construction of a twisted FBI transform. We also investigate the connections between pseudo-spectra and boundary conditions in the semi-classical limit.

  8. 22 CFR 227.600 - Semi-annual compilation.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 22 Foreign Relations 1 2012-04-01 2012-04-01 false Semi-annual compilation. 227.600 Section 227.600 Foreign Relations AGENCY FOR INTERNATIONAL DEVELOPMENT NEW RESTRICTIONS ON LOBBYING Agency Reports § 227.600 Semi-annual compilation. (a) The head of each agency shall collect and compile the...

  9. 24 CFR 87.600 - Semi-annual compilation.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false Semi-annual compilation. 87.600 Section 87.600 Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development NEW RESTRICTIONS ON LOBBYING Agency Reports § 87.600 Semi-annual compilation. (a) The head of...

  10. 24 CFR 87.600 - Semi-annual compilation.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false Semi-annual compilation. 87.600 Section 87.600 Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development NEW RESTRICTIONS ON LOBBYING Agency Reports § 87.600 Semi-annual compilation. (a) The head of...

  11. 22 CFR 227.600 - Semi-annual compilation.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 22 Foreign Relations 1 2014-04-01 2014-04-01 false Semi-annual compilation. 227.600 Section 227.600 Foreign Relations AGENCY FOR INTERNATIONAL DEVELOPMENT NEW RESTRICTIONS ON LOBBYING Agency Reports § 227.600 Semi-annual compilation. (a) The head of each agency shall collect and compile the...

  12. 24 CFR 87.600 - Semi-annual compilation.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 24 Housing and Urban Development 1 2014-04-01 2014-04-01 false Semi-annual compilation. 87.600 Section 87.600 Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development NEW RESTRICTIONS ON LOBBYING Agency Reports § 87.600 Semi-annual compilation. (a) The head of...

  13. 24 CFR 87.600 - Semi-annual compilation.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Semi-annual compilation. 87.600 Section 87.600 Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development NEW RESTRICTIONS ON LOBBYING Agency Reports § 87.600 Semi-annual compilation. (a) The head of...

  14. 24 CFR 87.600 - Semi-annual compilation.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 24 Housing and Urban Development 1 2013-04-01 2013-04-01 false Semi-annual compilation. 87.600 Section 87.600 Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development NEW RESTRICTIONS ON LOBBYING Agency Reports § 87.600 Semi-annual compilation. (a) The head of...

  15. 22 CFR 227.600 - Semi-annual compilation.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 22 Foreign Relations 1 2011-04-01 2011-04-01 false Semi-annual compilation. 227.600 Section 227.600 Foreign Relations AGENCY FOR INTERNATIONAL DEVELOPMENT NEW RESTRICTIONS ON LOBBYING Agency Reports § 227.600 Semi-annual compilation. (a) The head of each agency shall collect and compile the...

  16. 22 CFR 227.600 - Semi-annual compilation.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 22 Foreign Relations 1 2013-04-01 2013-04-01 false Semi-annual compilation. 227.600 Section 227.600 Foreign Relations AGENCY FOR INTERNATIONAL DEVELOPMENT NEW RESTRICTIONS ON LOBBYING Agency Reports § 227.600 Semi-annual compilation. (a) The head of each agency shall collect and compile the...

  17. 77 FR 25523 - Semi-Annual Workforce Management Conference

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-30

    ... Office of the Secretary Semi-Annual Workforce Management Conference AGENCY: U.S. Department of... of Transportation, Office of the Secretary, announces the second Semi-Annual Workforce Management... for addressing labor/management issues, and safety. Registration Space is limited. Registration...

  18. An improved semi-implicit method for structural dynamics analysis

    NASA Technical Reports Server (NTRS)

    Park, K. C.

    1982-01-01

    A semi-implicit algorithm is presented for direct time integration of the structural dynamics equations. The algorithm avoids the factoring of the implicit difference solution matrix and mitigates the unacceptable accuracy losses which plagued previous semi-implicit algorithms. This substantial accuracy improvement is achieved by augmenting the solution matrix with two simple diagonal matrices of the order of the integration truncation error.

  19. 22 CFR 311.600 - Semi-annual compilation.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 22 Foreign Relations 2 2011-04-01 2009-04-01 true Semi-annual compilation. 311.600 Section 311.600 Foreign Relations PEACE CORPS NEW RESTRICTIONS ON LOBBYING Agency Reports § 311.600 Semi-annual compilation. (a) The head of each agency shall collect and compile the disclosure reports (see appendix B)...

  20. 22 CFR 311.600 - Semi-annual compilation.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 22 Foreign Relations 2 2014-04-01 2014-04-01 false Semi-annual compilation. 311.600 Section 311.600 Foreign Relations PEACE CORPS NEW RESTRICTIONS ON LOBBYING Agency Reports § 311.600 Semi-annual compilation. (a) The head of each agency shall collect and compile the disclosure reports (see appendix B)...

  1. 22 CFR 311.600 - Semi-annual compilation.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 22 Foreign Relations 2 2012-04-01 2009-04-01 true Semi-annual compilation. 311.600 Section 311.600 Foreign Relations PEACE CORPS NEW RESTRICTIONS ON LOBBYING Agency Reports § 311.600 Semi-annual compilation. (a) The head of each agency shall collect and compile the disclosure reports (see appendix B)...

  2. 22 CFR 311.600 - Semi-annual compilation.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 22 Foreign Relations 2 2010-04-01 2010-04-01 true Semi-annual compilation. 311.600 Section 311.600 Foreign Relations PEACE CORPS NEW RESTRICTIONS ON LOBBYING Agency Reports § 311.600 Semi-annual compilation. (a) The head of each agency shall collect and compile the disclosure reports (see appendix B)...

  3. 22 CFR 311.600 - Semi-annual compilation.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 22 Foreign Relations 2 2013-04-01 2009-04-01 true Semi-annual compilation. 311.600 Section 311.600 Foreign Relations PEACE CORPS NEW RESTRICTIONS ON LOBBYING Agency Reports § 311.600 Semi-annual compilation. (a) The head of each agency shall collect and compile the disclosure reports (see appendix B)...

  4. Symmetry of semi-reduced lattices.

    PubMed

    Stróż, Kazimierz

    2015-05-01

    The main result of this work is extension of the famous characterization of Bravais lattices according to their metrical, algebraic and geometric properties onto a wide class of primitive lattices (including Buerger-reduced, nearly Buerger-reduced and a substantial part of Delaunay-reduced) related to low-restricted semi-reduced descriptions (s.r.d.'s). While the `geometric' operations in Bravais lattices map the basis vectors into themselves, the `arithmetic' operators in s.r.d. transform the basis vectors into cell vectors (basis vectors, face or space diagonals) and are represented by matrices from the set {\\bb V} of all 960 matrices with the determinant ±1 and elements {0, ±1} of the matrix powers. A lattice is in s.r.d. if the moduli of off-diagonal elements in both the metric tensors M and M(-1) are smaller than corresponding diagonal elements sharing the same column or row. Such lattices are split into 379 s.r.d. types relative to the arithmetic holohedries. Metrical criteria for each type do not need to be explicitly given but may be modelled as linear derivatives {\\bb M}(p,q,r), where {\\bb M} denotes the set of 39 highest-symmetry metric tensors, and p,q,r describe changes of appropriate interplanar distances. A sole filtering of {\\bb V} according to an experimental s.r.d. metric and subsequent geometric interpretation of the filtered matrices lead to mathematically stable and rich information on the Bravais-lattice symmetry and deviations from the exact symmetry. The emphasis on the crystallographic features of lattices was obtained by shifting the focus (i) from analysis of a lattice metric to analysis of symmetry matrices [Himes & Mighell (1987). Acta Cryst. A43, 375-384], (ii) from the isometric approach and invariant subspaces to the orthogonality concept {some ideas in Le Page [J. Appl. Cryst. (1982), 15, 255-259]} and splitting indices [Stróż (2011). Acta Cryst. A67, 421-429] and (iii) from fixed cell transformations to transformations

  5. Semi-Analytical Benchmarks for MCNP6

    SciTech Connect

    Grechanuk, Pavel Aleksandrovi

    2016-11-07

    Code verification is an extremely important process that involves proving or disproving the validity of code algorithms by comparing them against analytical results of the underlying physics or mathematical theory on which the code is based. Monte Carlo codes such as MCNP6 must undergo verification and testing upon every release to ensure that the codes are properly simulating nature. Specifically, MCNP6 has multiple sets of problems with known analytic solutions that are used for code verification. Monte Carlo codes primarily specify either current boundary sources or a volumetric fixed source, either of which can be very complicated functions of space, energy, direction and time. Thus, most of the challenges with modeling analytic benchmark problems in Monte Carlo codes come from identifying the correct source definition to properly simulate the correct boundary conditions. The problems included in this suite all deal with mono-energetic neutron transport without energy loss, in a homogeneous material. The variables that differ between the problems are source type (isotropic/beam), medium dimensionality (infinite/semi-infinite), etc.

  6. Semi-automated contour recognition using DICOMautomaton

    NASA Astrophysics Data System (ADS)

    Clark, H.; Wu, J.; Moiseenko, V.; Lee, R.; Gill, B.; Duzenli, C.; Thomas, S.

    2014-03-01

    Purpose: A system has been developed which recognizes and classifies Digital Imaging and Communication in Medicine contour data with minimal human intervention. It allows researchers to overcome obstacles which tax analysis and mining systems, including inconsistent naming conventions and differences in data age or resolution. Methods: Lexicographic and geometric analysis is used for recognition. Well-known lexicographic methods implemented include Levenshtein-Damerau, bag-of-characters, Double Metaphone, Soundex, and (word and character)-N-grams. Geometrical implementations include 3D Fourier Descriptors, probability spheres, boolean overlap, simple feature comparison (e.g. eccentricity, volume) and rule-based techniques. Both analyses implement custom, domain-specific modules (e.g. emphasis differentiating left/right organ variants). Contour labels from 60 head and neck patients are used for cross-validation. Results: Mixed-lexicographical methods show an effective improvement in more than 10% of recognition attempts compared with a pure Levenshtein-Damerau approach when withholding 70% of the lexicon. Domain-specific and geometrical techniques further boost performance. Conclusions: DICOMautomaton allows users to recognize contours semi-automatically. As usage increases and the lexicon is filled with additional structures, performance improves, increasing the overall utility of the system.

  7. Semi-Automatic Digital Landform Mapping

    NASA Astrophysics Data System (ADS)

    Schneider, Martin; Klein, Reinhard

    In this paper a framework for landform mapping on digital aerial photos and elevation models is presented. The developed mapping tools are integrated in a real-time terrain visualization engine in order to improve the visual recovery and identification of objects. Moreover, semi-automatic image segmentation techniques are built into the mapping tools to make object specification faster and easier without reducing accuracy. Thus, the high level cognitive task of object identification is left to the user whereas the segmentation algorithm performs the low level task of capturing the fine details of the object boundary. In addition to that, the user is able to supply additional photos of regions of interest and to match them with the textured DEM. The matched photos do not only drastically increase the visual information content of the data set but also contribute to the mapping process. Using this additional information precise landform mapping becomes even possible at steep slopes although they are only insufficiently represented in aerial imagery. As proof of concept we mapped several geomorphological structures in a high alpine valley.

  8. High Order Semi-Lagrangian Advection Scheme

    NASA Astrophysics Data System (ADS)

    Malaga, Carlos; Mandujano, Francisco; Becerra, Julian

    2014-11-01

    In most fluid phenomena, advection plays an important roll. A numerical scheme capable of making quantitative predictions and simulations must compute correctly the advection terms appearing in the equations governing fluid flow. Here we present a high order forward semi-Lagrangian numerical scheme specifically tailored to compute material derivatives. The scheme relies on the geometrical interpretation of material derivatives to compute the time evolution of fields on grids that deform with the material fluid domain, an interpolating procedure of arbitrary order that preserves the moments of the interpolated distributions, and a nonlinear mapping strategy to perform interpolations between undeformed and deformed grids. Additionally, a discontinuity criterion was implemented to deal with discontinuous fields and shocks. Tests of pure advection, shock formation and nonlinear phenomena are presented to show performance and convergence of the scheme. The high computational cost is considerably reduced when implemented on massively parallel architectures found in graphic cards. The authors acknowledge funding from Fondo Sectorial CONACYT-SENER Grant Number 42536 (DGAJ-SPI-34-170412-217).

  9. Semi-empirical models of actinide alloying

    NASA Astrophysics Data System (ADS)

    Gibson, John K.; Haire, Richard G.; Ogawa, Toru

    1999-07-01

    Alloys of Np have been studied less than those of the neighboring elements, U and Pu; the higher actinides have received even less attention. Recent interest in 237Np, 241Am and other actinide isotopes as significant, long-lived and highly radiotoxic nuclear waste components, and particularly the roles of metallic materials in new handling/separations and remediation technologies, demands that this paucity of information concerning alloy behaviors be addressed. An additional interest in these materials arises from the possibility of revealing fundamental properties and bonding interactions, which would further characterize the unique electronic structures (e.g., 5f electrons) of the actinide elements. The small empirical knowledge basis presently available for understanding and modeling the alloying behavior of Np is summarized here, with emphasis on our recent results for the Np-Am, Np-Zr and Np-Fe phase diagrams. In view of the limited experimental data base for neptunium and the transplutonium metals, the value of semi-empirical intermetallic bonding models for predicting actinide alloy thermodynamics is evaluated.

  10. MEART: The Semi-Living Artist

    PubMed Central

    Bakkum, Douglas J.; Gamblen, Philip M.; Ben-Ary, Guy; Chao, Zenas C.; Potter, Steve M.

    2007-01-01

    Here, we and others describe an unusual neurorobotic project, a merging of art and science called MEART, the semi-living artist. We built a pneumatically actuated robotic arm to create drawings, as controlled by a living network of neurons from rat cortex grown on a multi-electrode array (MEA). Such embodied cultured networks formed a real-time closed-loop system which could now behave and receive electrical stimulation as feedback on its behavior. We used MEART and simulated embodiments, or animats, to study the network mechanisms that produce adaptive, goal-directed behavior. This approach to neural interfacing will help instruct the design of other hybrid neural-robotic systems we call hybrots. The interfacing technologies and algorithms developed have potential applications in responsive deep brain stimulation systems and for motor prosthetics using sensory components. In a broader context, MEART educates the public about neuroscience, neural interfaces, and robotics. It has paved the way for critical discussions on the future of bio-art and of biotechnology. PMID:18958276

  11. Parallel algorithms for semi-lagrangian advection

    NASA Astrophysics Data System (ADS)

    Malevsky, A. V.; Thomas, S. J.

    1997-08-01

    Numerical time step limitations associated with the explicit treatment of advection-dominated problems in computational fluid dynamics are often relaxed by employing Eulerian-Lagrangian methods. These are also known as semi-Lagrangian methods in the atmospheric sciences. Such methods involve backward time integration of a characteristic equation to find the departure point of a fluid particle arriving at a Eulerian grid point. The value of the advected field at the departure point is obtained by interpolation. Both the trajectory integration and repeated interpolation influence accuracy. We compare the accuracy and performance of interpolation schemes based on piecewise cubic polynomials and cubic B-splines in the context of a distributed memory, parallel computing environment. The computational cost and interprocessor communication requirements for both methods are reported. Spline interpolation has better conservation properties but requires the solution of a global linear system, initially appearing to hinder a distributed memory implementation. The proposed parallel algorithm for multidimensional spline interpolation has almost the same communication overhead as local piecewise polynomial interpolation. We also compare various techniques for tracking trajectories given different values for the Courant number. Large Courant numbers require a high-order ODE solver involving multiple interpolations of the velocity field.

  12. Représentativité de l'échantillonnage géochimique et hydrodynamique en nappe libre du milieu semi-aride (Reliability of geochemical and hydrodynamic sample in a semi-arid water table)

    NASA Astrophysics Data System (ADS)

    Favreau, G.; Leduc, C.; Marlin, C.

    2000-11-01

    This paper evaluates the reliability of the geochemical and hydrodynamic sampling in a phreatic aquifer of semi-arid Africa. These remarks are based on a dense network and on detailed data collected for about ten years in the Continental Terminal water table near Niamey, Niger. The natural potentiometric fluctuations are seasonal (up to 6 m during the rainy season) and interannual (up to 10 m since the 1960s). Hydrodynamic measurements can be disturbed by artificial flooding into the wells (20% of the network) and by domestic drawings (up to 2 m of lowering). Geochemical characteristics can vary seasonally: isotopic modifications and salinity increase near recharge areas, with more stability further away. They can also vary artificially in wells because of their large opening towards the open air. Artifical increases of salinity of one order of magnitude and contaminations of 14C activities of up to 20 pmC occur in some wells by atmospheric dust inputs or organic matter which was has fallen into the well. In conclusion, some recommendations are given for a representative sampling in semi-arid phreatic aquifers.

  13. 77 FR 48540 - Agency Information Collection Activities: Extension of a Currently Approved Collection; Semi...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-08-14

    ... Information Collection Activities: Extension of a Currently Approved Collection; Semi-Annual Progress Report.../Collection: Semi-Annual Progress Report for Grantees from the Semi-Annual Progress Report for the Sexual... one hour to complete a semi-annual progress report. The semi-annual progress report is divided......

  14. On the efficiency of semi-implicit and semi-Lagrangian spectral methods for the calculation of incompressible flows

    NASA Astrophysics Data System (ADS)

    Xu, Chuanju; Pasquetti, Richard

    2001-02-01

    Classical semi-implicit backward Euler/Adams-Bashforth time discretizations of the Navier-Stokes equations induce, for high-Reynolds number flows, severe restrictions on the time step. Such restrictions can be relaxed by using semi-Lagrangian schemes essentially based on splitting the full problem into an explicit transport step and an implicit diffusion step. In comparison with the standard characteristics method, the semi-Lagrangian method has the advantage of being much less CPU time consuming where spectral methods are concerned. This paper is devoted to the comparison of the semi-implicit and semi-Lagrangian approaches, in terms of stability, accuracy and computational efficiency. Numerical results on the advection equation, Burger's equation and finally two- and three-dimensional Navier-Stokes equations, using spectral elements or a collocation method, are provided. Copyright

  15. Structure and function of the hemocyanin from a semi-terrestrial crab, Ocypode quadrata.

    PubMed

    Johnson, B A

    1987-01-01

    Structural and functional studies of the hemocyanin of the semi-terrestrial ghost crab, Ocypode quadrata, demonstrate a variety of differences in comparison to the hemocyanin of aquatic crabs. These differences may be related to the terrestrial habit of this crab. Unlike aquatic crabs, the major (56%) blood component is the hexamer; the remaining 44% is dodecamer. The hexamers and dodecamers are not in rapid equilibrium. Electrophoretic analysis of the subunit composition indicates three major components referred to as 1, 3, and 4, and one minor component referred to as component 2. These components, although electrophoretically distinct, are alike immunologically. Components 1 and 2 are essentially absent from purified hexamers, whereas they compose 1/3 of the subunits in dodecamers. These results suggest that they are involved in linking hexamers to form dodecamers, and that two, rather than one, subunits are involved in the bridge. Oxygen-binding measurements show a higher degree of cooperativity, and a much reduced allosteric effect of L-lactate on the dialyzed hemocyanin as compared to the hemocyanin of aquatic crabs. Exercise rapidly induces a large drop in hemolymph pH (0.5 units) and a corresponding increase in lactate concentrations (to 10 mM).

  16. Reef-associated crustacean fauna: biodiversity estimates using semi-quantitative sampling and DNA barcoding

    NASA Astrophysics Data System (ADS)

    Plaisance, L.; Knowlton, N.; Paulay, G.; Meyer, C.

    2009-12-01

    The cryptofauna associated with coral reefs accounts for a major part of the biodiversity in these ecosystems but has been largely overlooked in biodiversity estimates because the organisms are hard to collect and identify. We combine a semi-quantitative sampling design and a DNA barcoding approach to provide metrics for the diversity of reef-associated crustacean. Twenty-two similar-sized dead heads of Pocillopora were sampled at 10 m depth from five central Pacific Ocean localities (four atolls in the Northern Line Islands and in Moorea, French Polynesia). All crustaceans were removed, and partial cytochrome oxidase subunit I was sequenced from 403 individuals, yielding 135 distinct taxa using a species-level criterion of 5% similarity. Most crustacean species were rare; 44% of the OTUs were represented by a single individual, and an additional 33% were represented by several specimens found only in one of the five localities. The Northern Line Islands and Moorea shared only 11 OTUs. Total numbers estimated by species richness statistics (Chao1 and ACE) suggest at least 90 species of crustaceans in Moorea and 150 in the Northern Line Islands for this habitat type. However, rarefaction curves for each region failed to approach an asymptote, and Chao1 and ACE estimators did not stabilize after sampling eight heads in Moorea, so even these diversity figures are underestimates. Nevertheless, even this modest sampling effort from a very limited habitat resulted in surprisingly high species numbers.

  17. Inflow Ducting in High-Volume-Flow Subsonic Anechoic Chambers.

    DTIC Science & Technology

    1983-10-12

    resin with 1/4" (6.4mm) thick walls and its inner diameter is 9 1/2" (21.4cm). A bellmouth was fabricated from expanded polystyrene and fitted to the...is modeled with steel-angle-reinforced 1/4" (6.4mm) plywood walls that are lined with expanded polystyrene wedges. Great care was taken during the...t, mounted, the wedges are made of expanded polystyrene , and were cut to shape by the supplier with a hot wire system. The wedges are p

  18. Evaluation of RF Anechoic Chamber Fire Protection Systems

    DTIC Science & Technology

    1980-07-01

    Tt’mnernt tire Lec I Itr rn t Riidfitt ion l~it v or patte’rn 𔃻.nuzii 9vs4trv Soundl t cvr tun:i I on in i n Sme II Fee I \\O.S’upervi sec TRANSMIT (:i/no...extinguishment. Almost all injuries and fatalities from those agents were from exposure to the natural vapor--often because of misuse. The 800*C pyrolysis data pre...potential from discharge Electrical and electronic Corrosion possible None from agent as Avoidance requires equipment from agent pyrolysis long as

  19. Structures of SemiSWEET transporters in two distinct conformations

    PubMed Central

    Fan, Chao; Chen, Li-Qing; Xu, Sophia; Perry, Kay; Frommer, Wolf B.; Feng, Liang

    2015-01-01

    SemiSWEETs and SWEETs are mono- and disaccharide transporters present from Archaea to higher plants and humans1-3. SWEETs play crucial roles in cellular sugar efflux processes, i.e. phloem loading4, pollen nutrition5 and nectar secretion6. Their bacterial homologs, SemiSWEETs, are among the smallest known transporters1,3. Here we show SemiSWEET, consisting of a triple-helix-bundle (THB), forms a symmetric parallel dimer to create the translocation pathway. Two SemiSWEET isoforms were crystallized in apparent open and occluded states, indicating that SemiSWEETs/SWEETs are transporters that undergo rocking-type movements during the transport cycle. The topology of THB is similar to the basic building block in MFS transporters (GLUTs, SUTs), indicating that they may have evolved from an ancestral THB into a parallel configuration to produce 6/6+1 transmembrane-helix pores for SemiSWEETs/SWEETs, and an antiparallel configuration of 2×2 THBs to generate 12 transmembrane-helix pores for MFS transporters. Given the similarity of SemiSWEETs/SWEETs to PQ-loop amino acid transporters and mitochondrial MPC organic acid transporters, the structures characterized here may also be relevant for other MtN3 clan transporters7-9. PMID:25186729

  20. A Bayesian Assessment of Seismic Semi-Periodicity Forecasts

    NASA Astrophysics Data System (ADS)

    Nava, F.; Quinteros, C.; Glowacka, E.; Frez, J.

    2016-01-01

    Among the schemes for earthquake forecasting, the search for semi-periodicity during large earthquakes in a given seismogenic region plays an important role. When considering earthquake forecasts based on semi-periodic sequence identification, the Bayesian formalism is a useful tool for: (1) assessing how well a given earthquake satisfies a previously made forecast; (2) re-evaluating the semi-periodic sequence probability; and (3) testing other prior estimations of the sequence probability. A comparison of Bayesian estimates with updated estimates of semi-periodic sequences that incorporate new data not used in the original estimates shows extremely good agreement, indicating that: (1) the probability that a semi-periodic sequence is not due to chance is an appropriate estimate for the prior sequence probability estimate; and (2) the Bayesian formalism does a very good job of estimating corrected semi-periodicity probabilities, using slightly less data than that used for updated estimates. The Bayesian approach is exemplified explicitly by its application to the Parkfield semi-periodic forecast, and results are given for its application to other forecasts in Japan and Venezuela.

  1. Planning and scheduling of semi-urgent surgeries.

    PubMed

    Zonderland, Maartje E; Boucherie, Richard J; Litvak, Nelly; Vleggeert-Lankamp, Carmen L A M

    2010-09-01

    This paper investigates the trade-off between cancellations of elective surgeries due to semi-urgent surgeries, and unused operating room (OR) time due to excessive reservation of OR time for semi-urgent surgeries. Semi-urgent surgeries, to be performed soon but not necessarily today, pose an uncertain demand on available hospital resources, and interfere with the planning of elective patients. For a highly utilized OR, reservation of OR time for semi-urgent surgeries avoids excessive cancellations of elective surgeries, but may also result in unused OR time, since arrivals of semi-urgent patients are unpredictable. First, using a queuing theory framework, we evaluate the OR capacity needed to accommodate every incoming semi-urgent surgery. Second, we introduce another queuing model that enables a trade-off between the cancelation rate of elective surgeries and unused OR time. Third, based on Markov decision theory, we develop a decision support tool that assists the scheduling process of elective and semi-urgent surgeries. We demonstrate our results with actual data obtained from a department of neurosurgery.

  2. Nebkha patterns in semi-arid environments

    NASA Astrophysics Data System (ADS)

    Nield, J. M.; Gillies, J. A.; Nickling, W. G.

    2014-12-01

    In semi-arid supply-limited, environments, nehbka dunes typically form through ecogeomorphic feedbacks. The size, shape and orientation of these dunes are controlled by the interactions between vegetation growth and aeolian sedimentations processes. Once established, these dune patterns modify sediment transport and often form streets of bare surfaces between dune corridors. We examine typical dune and vegetation patterns that form with varying amounts of sediment availability and nebkha maturity at Jornada in the Chihuahuan Desert, New Mexico, USA using terrestrial laser scanning (TLS) to separate the plant and sand elements. Manual and automated TLS shrub height extractions compare well at all sites (p = 0.48-0.94) enabling the quantification of both solid and plant roughness element components in three dimensions. We find that there is a switch in orientation of the dune elements with respect to dominant wind direction from perpendicular to parallel as the landscape develops from an incipient to mature configuration and mesquite-nebkha streets are enhanced. As the nebkha dunes develop the surface coverage of bare sand increases and dune surfaces exceed the size of their companion shrubs. Roughness density also increases at the mature dune site. Individual shrub orientations remain similar at each site, but nebkhas typically host multiple shrub crowns at the mature site. Over a two year period up to 20 cm of erosion was measured on the upwind faces of the mature nebkha dunes, in agreement with the dominant annual wind direction. However, deposition patterns were more diffuse and influenced by the vegetation patterns. This study highlights the importance of ecogeomorphic interactions in shaping nebkha landscape patterns.

  3. Semi-automatic knee cartilage segmentation

    NASA Astrophysics Data System (ADS)

    Dam, Erik B.; Folkesson, Jenny; Pettersen, Paola C.; Christiansen, Claus

    2006-03-01

    Osteo-Arthritis (OA) is a very common age-related cause of pain and reduced range of motion. A central effect of OA is wear-down of the articular cartilage that otherwise ensures smooth joint motion. Quantification of the cartilage breakdown is central in monitoring disease progression and therefore cartilage segmentation is required. Recent advances allow automatic cartilage segmentation with high accuracy in most cases. However, the automatic methods still fail in some problematic cases. For clinical studies, even if a few failing cases will be averaged out in the overall results, this reduces the mean accuracy and precision and thereby necessitates larger/longer studies. Since the severe OA cases are often most problematic for the automatic methods, there is even a risk that the quantification will introduce a bias in the results. Therefore, interactive inspection and correction of these problematic cases is desirable. For diagnosis on individuals, this is even more crucial since the diagnosis will otherwise simply fail. We introduce and evaluate a semi-automatic cartilage segmentation method combining an automatic pre-segmentation with an interactive step that allows inspection and correction. The automatic step consists of voxel classification based on supervised learning. The interactive step combines a watershed transformation of the original scan with the posterior probability map from the classification step at sub-voxel precision. We evaluate the method for the task of segmenting the tibial cartilage sheet from low-field magnetic resonance imaging (MRI) of knees. The evaluation shows that the combined method allows accurate and highly reproducible correction of the segmentation of even the worst cases in approximately ten minutes of interaction.

  4. Semi-span model testing in the National Transonic Facility

    NASA Technical Reports Server (NTRS)

    Chokani, Ndaona; Milholen, William E., II

    1993-01-01

    A semi-span testing technique has been proposed for the NASA Langley Research Center's National Transonic Facility (NTF). Semi-span testing has several advantages including (1) larger model size, giving increased Reynolds number capability; (2) improved model fidelity, allowing ease of flap and slat positioning which ultimately improves data quality; and (3) reduced construction costs compared with a full-span model. In addition, the increased model size inherently allows for increased model strength, reducing aeroelastic effects at the high dynamic pressure levels necessary to simulate flight Reynolds numbers. The Energy Efficient Transport (EET) full-span model has been modified to become the EET semi-span model. The full-span EET model was tested extensively at both NASA LRC and NASA Ames Research Center. The available full-span data will be useful in validating the semi-span test strategy in the NTF. In spite of the advantages discussed above, the use of a semi-span model does introduce additional challenges which must be addressed in the testing procedure. To minimize the influence of the sidewall boundary layer on the flow over the semi-span model, the model must be off-set from the sidewall. The objective is to remove the semi-span model from the sidewall boundary layer by use of a stand-off geometry. When this is done however, the symmetry along the centerline of the full-span model is lost when the semi-span model is mounted on the wind tunnel sidewall. In addition, the large semi-span model will impose a significant pressure loading on the sidewall boundary layer, which may cause separation. Even under flow conditions where the sidewall boundary layer remains attached, the sidewall boundary layer may adversely effect the flow over the semi-span model. Also, the increased model size and sidewall mounting requires a modified wall correction strategy. With these issues in mind, the semi-span model has been well instrumented with surface pressure taps to

  5. High-Performance, Semi-Interpenetrating Polymer Network

    NASA Technical Reports Server (NTRS)

    Pater, Ruth H.; Lowther, Sharon E.; Smith, Janice Y.; Cannon, Michelle S.; Whitehead, Fred M.; Ely, Robert M.

    1992-01-01

    High-performance polymer made by new synthesis in which one or more easy-to-process, but brittle, thermosetting polyimides combined with one or more tough, but difficult-to-process, linear thermoplastics to yield semi-interpenetrating polymer network (semi-IPN) having combination of easy processability and high tolerance to damage. Two commercially available resins combined to form tough, semi-IPN called "LaRC-RP49." Displays improvements in toughness and resistance to microcracking. LaRC-RP49 has potential as high-temperature matrix resin, adhesive, and molding resin. Useful in aerospace, automotive, and electronic industries.

  6. Method and apparatus for semi-solid material processing

    DOEpatents

    Han, Qingyou [Knoxville, TN; Jian, Xiaogang [Knoxville, TN; Xu, Hanbing [Knoxville, TN; Meek, Thomas T [Knoxville, TN

    2009-11-24

    A method of forming a material includes the steps of: vibrating a molten material at an ultrasonic frequency while cooling the material to a semi-solid state to form non-dendritic grains therein; forming the semi-solid material into a desired shape; and cooling the material to a solid state. The method makes semi-solid castings directly from molten materials (usually a metal), produces grain size usually in the range of smaller than 50 .mu.m, and can be easily retrofitted into existing conventional forming maching.

  7. Method and apparatus for semi-solid material processing

    DOEpatents

    Han, Qingyou [Knoxville, TN; Jian, Xiaogang [Knoxville, TN; Xu, Hanbing [Knoxville, TN; Meek, Thomas T [Knoxville, TN

    2009-02-24

    A method of forming a material includes the steps of: vibrating a molten material at an ultrasonic frequency while cooling the material to a semi-solid state to form non-dendritic grains therein; forming the semi-solid material into a desired shape; and cooling the material to a solid state. The method makes semi-solid castings directly from molten materials (usually a metal), produces grain size usually in the range of smaller than 50 .mu.m, and can be easily retrofitted into existing conventional forming machine.

  8. Method and apparatus for semi-solid material processing

    DOEpatents

    Han, Qingyou; Jian, Xiaogang; Xu, Hanbing; Meek, Thomas T.

    2007-05-15

    A method of forming a material includes the steps of: vibrating a molten material at an ultrasonic frequency while cooling the material to a semi-solid state to form non-dendritic grains therein; forming the semi-solid material into a desired shape; and cooling the material to a solid state. The method makes semi-solid castings directly from molten materials (usually a metal), produces grain size usually in the range of smaller than 50 .mu.m, and can be easily retrofitted into existing conventional forming machine.

  9. Waste biorefinery in arid/semi-arid regions.

    PubMed

    Bastidas-Oyanedel, Juan-Rodrigo; Fang, Chuanji; Almardeai, Saleha; Javid, Usama; Yousuf, Ahasa; Schmidt, Jens Ejbye

    2016-09-01

    The utilization of waste biorefineries in arid/semi-arid regions is advisable due to the reduced sustainable resources in arid/semi-arid regions, e.g. fresh water and biomass. This review focuses on biomass residues available in arid/semi-arid regions, palm trees residues, seawater biomass based residues (coastal arid/semi-arid regions), and the organic fraction of municipal solid waste. The present review aims to describe and discuss the availability of these waste biomasses, their conversion to value chemicals by waste biorefinery processes. For the case of seawater biomass based residues it was reviewed and advise the use of seawater in the biorefinery processes, in order to decrease the use of fresh water.

  10. Stationary semi-solid battery module and method of manufacture

    DOEpatents

    Slocum, Alexander; Doherty, Tristan; Bazzarella, Ricardo; Cross, III, James C.; Limthongkul, Pimpa; Duduta, Mihai; Disko, Jeffry; Yang, Allen; Wilder, Throop; Carter, William Craig; Chiang, Yet-Ming

    2015-12-01

    A method of manufacturing an electrochemical cell includes transferring an anode semi-solid suspension to an anode compartment defined at least in part by an anode current collector and an separator spaced apart from the anode collector. The method also includes transferring a cathode semi-solid suspension to a cathode compartment defined at least in part by a cathode current collector and the separator spaced apart from the cathode collector. The transferring of the anode semi-solid suspension to the anode compartment and the cathode semi-solid to the cathode compartment is such that a difference between a minimum distance and a maximum distance between the anode current collector and the separator is maintained within a predetermined tolerance. The method includes sealing the anode compartment and the cathode compartment.

  11. Semi-Hyperbolic Mappings, Condensing Operators, and Neutral Delay Equations

    NASA Astrophysics Data System (ADS)

    Al-Nayef, A. A.; Kloeden, P. E.; Pokrovskii, A. V.

    1997-07-01

    Semi-hyperbolic mappings in Banach spaces are Lipschitz continuous and not necessarily invertible. Like hyperbolic mappings, they involve a splitting into stable and unstable spaces, but a slight leakage from the strict invariance of the spaces is possible and the unstable subspaces are assumed to be finite dimensional. It is shown that semi-hyperbolic mappings are locallyψ-contracting, whereψis the Hausdorff measure of noncompactness, and that a linear operator is semi-hyperbolic if and only if it isψ-contracting and has no spectral values on the unit circle. A bishadowing result, which combines both direct and indirect forms of shadowing, is extended to semi-hyperbolic mappings in Banach spaces with locally condensing continuous comparison mappings. The result is applied to linear neutral delay equations with nonsmooth perturbations.

  12. Virtual prototyping of a semi-active transfemoral prosthetic leg.

    PubMed

    Lui, Zhen Wei; Awad, Mohammed I; Abouhossein, Alireza; Dehghani-Sanij, Abbas A; Messenger, Neil

    2015-05-01

    This article presents a virtual prototyping study of a semi-active lower limb prosthesis to improve the functionality of an amputee during prosthesis-environment interaction for level ground walking. Articulated ankle-foot prosthesis and a single-axis semi-active prosthetic knee with active and passive operating modes were considered. Data for level ground walking were collected using a photogrammetric method in order to develop a base-line simulation model and with the hip kinematics input to verify the proposed design. The simulated results show that the semi-active lower limb prosthesis is able to move efficiently in passive mode, and the activation time of the knee actuator can be reduced by approximately 50%. Therefore, this semi-active system has the potential to reduce the energy consumption of the actuators required during level ground walking and requires less compensation from the amputee due to lower deviation of the vertical excursion of body centre of mass.

  13. Method for producing heat-resistant semi-inorganic compounds

    NASA Technical Reports Server (NTRS)

    Yajima, S.; Okamura, K.; Shishido, T.; Hasegawa, Y.

    1983-01-01

    The method for producing a heat resistant, semi-inorganic compound is discussed. Five examples in which various alcohols, phenols, and aromatic carbonic acids are used to test heat resistance and solubility are provided.

  14. Infinitesimal rigidity of hyperquadrics in semi-Euclidean space

    NASA Astrophysics Data System (ADS)

    Shin, An Sook; Kim, Hobum; Han, Hyelim

    2016-12-01

    In this paper, we show that hyperquadrics are infinitesimally rigid in a semi-Euclidean space. We also show that hypersurfaces of hyperquadrics cut by hyperplanes not passing through the origin are infinitesimally rigid in the hyperquadrics, whereas those cut by hyperplanes through the origin are not infinitesimally rigid in hyperquadrics. Furthermore, we prove that any hypersurface in a semi-Euclidean space containing some open subset of a hyperplane is not infinitesimally rigid.

  15. Relaxation, Structure and Properties of Semi-coherent Interfaces

    DOE PAGES

    Shao, Shuai; Wang, Jian

    2015-11-05

    Materials containing high density of interfaces are promising candidates for future energy technologies, because interfaces acting as sources, sinks, and barriers for defects can improve mechanical and irradiation properties of materials. Semi-coherent interface widely occurring in various materials is composed of a network of misfit dislocations and coherent regions separated by misfit dislocations. Lastly, in this article, we review relaxation mechanisms, structure and properties of (111) semi-coherent interfaces in face centered cubic structures.

  16. Semi-continuous detection of mercury in gases

    DOEpatents

    Granite, Evan J [Wexford, PA; Pennline, Henry W [Bethel Park, PA

    2011-12-06

    A new method for the semi-continuous detection of heavy metals and metalloids including mercury in gaseous streams. The method entails mass measurement of heavy metal oxides and metalloid oxides with a surface acoustic wave (SAW) sensor having an uncoated substrate. An array of surface acoustic wave (SAW) sensors can be used where each sensor is for the semi-continuous emission monitoring of a particular heavy metal or metalloid.

  17. Semi-Lagrangian integration schemes for atmospheric models - A review

    SciTech Connect

    Staniforth, A.; Cote, J. )

    1991-09-01

    The semi-Lagrangian methodology is described for a hierarchy of applications (passive advection, forced advection, and coupled sets of equation) of increasing complexity, in one, two, and three dimensions. Attention is focused on its accuracy, stability, and efficiency properties. Recent developments in applying semi-Lagrangian methods to 2D and 3D atmospheric flows in both Cartesian and spherical geometries are then reviewed. Finally, the current status of development is summarized, followed by a short discussion of future perspectives. 80 refs.

  18. Semi-solid electrodes having high rate capability

    DOEpatents

    Chiang, Yet-Ming; Duduta, Mihai; Holman, Richard; Limthongkul, Pimpa; Tan, Taison

    2016-06-07

    Embodiments described herein relate generally to electrochemical cells having high rate capability, and more particularly to devices, systems and methods of producing high capacity and high rate capability batteries having relatively thick semi-solid electrodes. In some embodiments, an electrochemical cell includes an anode and a semi-solid cathode. The semi-solid cathode includes a suspension of an active material of about 35% to about 75% by volume of an active material and about 0.5% to about 8% by volume of a conductive material in a non-aqueous liquid electrolyte. An ion-permeable membrane is disposed between the anode and the semi-solid cathode. The semi-solid cathode has a thickness of about 250 .mu.m to about 2,000 .mu.m, and the electrochemical cell has an area specific capacity of at least about 7 mAh/cm.sup.2 at a C-rate of C/4. In some embodiments, the semi-solid cathode slurry has a mixing index of at least about 0.9.

  19. Neuromantic – from Semi-Manual to Semi-Automatic Reconstruction of Neuron Morphology

    PubMed Central

    Myatt, Darren R.; Hadlington, Tye; Ascoli, Giorgio A.; Nasuto, Slawomir J.

    2012-01-01

    The ability to create accurate geometric models of neuronal morphology is important for understanding the role of shape in information processing. Despite a significant amount of research on automating neuron reconstructions from image stacks obtained via microscopy, in practice most data are still collected manually. This paper describes Neuromantic, an open source system for three dimensional digital tracing of neurites. Neuromantic reconstructions are comparable in quality to those of existing commercial and freeware systems while balancing speed and accuracy of manual reconstruction. The combination of semi-automatic tracing, intuitive editing, and ability of visualizing large image stacks on standard computing platforms provides a versatile tool that can help address the reconstructions availability bottleneck. Practical considerations for reducing the computational time and space requirements of the extended algorithm are also discussed. PMID:22438842

  20. A newer technique to program a semi adjustable articulator

    PubMed Central

    Venkateshwaran, R.; Karthigeyan, Suma; Manoharan, P. S.; Konchada, Jagadish; Ramaswamy, Manikandan; Bhuminathan

    2014-01-01

    Introduction: The difficulty in reproducing accurate angle of condylar guidance in semi-adjustable articulators. Purpose: The purpose of this study was to determine the correlation between the angle of horizontal condylar inclination obtained on a semi-adjustable articulator and the corresponding angle traced on a temporomandibular joint (TMJ) radiograph in completely edentulous subject. Materials and Methods: The horizontal condylar inclination angle was obtained in a semi-adjustable articulator by means of height tracer (extra oral tracing device) and interocclusal records to program the articulator in 21 subjects. TMJ radiograph were recorded by the same operator with same orthopantomogram (OPG) machine (planmeca). Tracings of inclines of articular eminence on the radiograph were compared with the angle obtained on a semi-adjustable articulator. Each measurement was made using manual methods of measuring angle. The results were subjected to the Pearson correlation statistical analysis (α =0.01). Results: The outline of the articular eminence in a TMJ tomogram radiographic image was identified and traced. A significant correlation was found between the horizontal condylar inclination on a semi-adjustable and the corresponding TMJ tomogram radiographic image for both right (R = 0.789; P = 0.001) and left (i = 0.747; P = 0.004) sides. Conclusion: The articular eminence traced on a TMJ tomogram image represents the horizontal condylar inclination with a mean difference of 5° in 21 subjects evaluated. PMID:25210356

  1. Improved semi-supervised online boosting for object tracking

    NASA Astrophysics Data System (ADS)

    Li, Yicui; Qi, Lin; Tan, Shukun

    2016-10-01

    The advantage of an online semi-supervised boosting method which takes object tracking problem as a classification problem, is training a binary classifier from labeled and unlabeled examples. Appropriate object features are selected based on real time changes in the object. However, the online semi-supervised boosting method faces one key problem: The traditional self-training using the classification results to update the classifier itself, often leads to drifting or tracking failure, due to the accumulated error during each update of the tracker. To overcome the disadvantages of semi-supervised online boosting based on object tracking methods, the contribution of this paper is an improved online semi-supervised boosting method, in which the learning process is guided by positive (P) and negative (N) constraints, termed P-N constraints, which restrict the labeling of the unlabeled samples. First, we train the classification by an online semi-supervised boosting. Then, this classification is used to process the next frame. Finally, the classification is analyzed by the P-N constraints, which are used to verify if the labels of unlabeled data assigned by the classifier are in line with the assumptions made about positive and negative samples. The proposed algorithm can effectively improve the discriminative ability of the classifier and significantly alleviate the drifting problem in tracking applications. In the experiments, we demonstrate real-time tracking of our tracker on several challenging test sequences where our tracker outperforms other related on-line tracking methods and achieves promising tracking performance.

  2. Enhanced manifold regularization for semi-supervised classification.

    PubMed

    Gan, Haitao; Luo, Zhizeng; Fan, Yingle; Sang, Nong

    2016-06-01

    Manifold regularization (MR) has become one of the most widely used approaches in the semi-supervised learning field. It has shown superiority by exploiting the local manifold structure of both labeled and unlabeled data. The manifold structure is modeled by constructing a Laplacian graph and then incorporated in learning through a smoothness regularization term. Hence the labels of labeled and unlabeled data vary smoothly along the geodesics on the manifold. However, MR has ignored the discriminative ability of the labeled and unlabeled data. To address the problem, we propose an enhanced MR framework for semi-supervised classification in which the local discriminative information of the labeled and unlabeled data is explicitly exploited. To make full use of labeled data, we firstly employ a semi-supervised clustering method to discover the underlying data space structure of the whole dataset. Then we construct a local discrimination graph to model the discriminative information of labeled and unlabeled data according to the discovered intrinsic structure. Therefore, the data points that may be from different clusters, though similar on the manifold, are enforced far away from each other. Finally, the discrimination graph is incorporated into the MR framework. In particular, we utilize semi-supervised fuzzy c-means and Laplacian regularized Kernel minimum squared error for semi-supervised clustering and classification, respectively. Experimental results on several benchmark datasets and face recognition demonstrate the effectiveness of our proposed method.

  3. Thermomechanical steels behaviors at semi-solid state

    NASA Astrophysics Data System (ADS)

    Traidi, K.; Favier, V.; Lestriez, P.; Debray, K.; Langlois, L.; Ranc, N.; Saby, M.; Mangin, P.

    2016-10-01

    Semisolid thixoforming is an intermediate process between casting and forging. The combination of the semi-solid state and globular microstructures leads to thixotropic properties of the material [1]. Thixoformingprocess presents several advantages such as energy efficiency, high production rates, smooth die filling, low shrinkage porosity, which together lead to near net shape capability and thus to fewer manufacturing steps than with classical methods. So far, there are only few applications of semisolid processing of highr melting point alloys [2]. Steel is a particularly challenging material to semi-solid process because of about 1400°C temperatures involved. Characterizing and modelling such semi-solid behaviour for steels is still challenging. The aim of the research work was to study the rheological properties of a suitable graded steel (LTT C38) designed for semi-solid processing. An experimental protocol was determined to characterize the thermomechanical behaviors and defect condition. Uniaxial tensile tests were carried out on semi-solid specimen having >0.8 solid fraction for different temperatures. The variation in both ductility and strength with temperature has been identified.

  4. Semi-Major Axis Knowledge and GPS Orbit Determination

    NASA Technical Reports Server (NTRS)

    Carpenter, J. Russell; Schiesser, Emil R.; Bauer, F. (Technical Monitor)

    2000-01-01

    In recent years spacecraft designers have increasingly sought to use onboard Global Positioning System receivers for orbit determination. The superb positioning accuracy of GPS has tended to focus more attention on the system's capability to determine the spacecraft's location at a particular epoch than on accurate orbit determination, per se. The determination of orbit plane orientation and orbit shape to acceptable levels is less challenging than the determination of orbital period or semi-major axis. It is necessary to address semi-major axis mission requirements and the GPS receiver capability for orbital maneuver targeting and other operations that require trajectory prediction. Failure to determine semi-major axis accurately can result in a solution that may not be usable for targeting the execution of orbit adjustment and rendezvous maneuvers. Simple formulas, charts, and rules of thumb relating position, velocity, and semi-major axis are useful in design and analysis of GPS receivers for near circular orbit operations, including rendezvous and formation flying missions. Space Shuttle flights of a number of different GPS receivers, including a mix of unfiltered and filtered solution data and Standard and Precise Positioning, Service modes, have been accomplished. These results indicate that semi-major axis is often not determined very accurately, due to a poor velocity solution and a lack of proper filtering to provide good radial and speed error correlation.

  5. Development of Semi-Span Model Test Techniques

    NASA Technical Reports Server (NTRS)

    Pulnam, L. Elwood (Technical Monitor); Milholen, William E., II; Chokani, Ndaona; McGhee, Robert J.

    1996-01-01

    A computational investigation was performed to support the development of a semi-span model test capability in the NASA Langley Research Center's National Transonic Facility. This capability is desirable for the testing of advanced subsonic transport aircraft at full-scale Reynolds numbers. A state-of-the-art three-dimensional Navier-Stokes solver was used to examine methods to improve the flow over a semi-span configuration. First, a parametric study is conducted to examine the influence of the stand-off height on the flow over the semi-span model. It is found that decreasing the stand-off height, below the maximum fuselage radius, improves the aerodynamic characteristics of the semi-span model. Next, active sidewall boundary layer control techniques are examined. Juncture region blowing jets, upstream tangential blowing, and sidewall suction are found to improve the flow over the aft portion of the semi-span model. Both upstream blowing and suction are found to reduce the sidewall boundary layer separation. The resulting near surface streamline patterns are improved, and found to be quite similar to the full-span results. Both techniques however adversely affect the pitching moment coefficient.

  6. Semi-coarsening multigrid methods for parallel computing

    SciTech Connect

    Jones, J.E.

    1996-12-31

    Standard multigrid methods are not well suited for problems with anisotropic coefficients which can occur, for example, on grids that are stretched to resolve a boundary layer. There are several different modifications of the standard multigrid algorithm that yield efficient methods for anisotropic problems. In the paper, we investigate the parallel performance of these multigrid algorithms. Multigrid algorithms which work well for anisotropic problems are based on line relaxation and/or semi-coarsening. In semi-coarsening multigrid algorithms a grid is coarsened in only one of the coordinate directions unlike standard or full-coarsening multigrid algorithms where a grid is coarsened in each of the coordinate directions. When both semi-coarsening and line relaxation are used, the resulting multigrid algorithm is robust and automatic in that it requires no knowledge of the nature of the anisotropy. This is the basic multigrid algorithm whose parallel performance we investigate in the paper. The algorithm is currently being implemented on an IBM SP2 and its performance is being analyzed. In addition to looking at the parallel performance of the basic semi-coarsening algorithm, we present algorithmic modifications with potentially better parallel efficiency. One modification reduces the amount of computational work done in relaxation at the expense of using multiple coarse grids. This modification is also being implemented with the aim of comparing its performance to that of the basic semi-coarsening algorithm.

  7. Development of the NTF-117S Semi-Span Balance

    NASA Technical Reports Server (NTRS)

    Lynn, Keith C.

    2010-01-01

    A new high-capacity semi-span force and moment balance has recently been developed for use at the National Transonic Facility at the NASA Langley Research Center. This new semi-span balance provides the NTF a new measurement capability that will support testing of semi-span test models at transonic high-lift testing regimes. Future testing utilizing this new balance capability will include active circulation control and propulsion simulation testing of semi-span transonic wing models. The NTF has recently implemented a new highpressure air delivery station that will provide both high and low mass flow pressure lines that are routed out to the semi-span models via a set high/low pressure bellows that are indirectly linked to the metric end of the NTF-117S balance. A new check-load stand is currently being developed to provide the NTF with an in-house capability that will allow for performing check-loads on the NTF-117S balance in order to determine the pressure tare affects on the overall performance of the balance. An experimental design is being developed that will allow for experimentally assessing the static pressure tare affects on the balance performance.

  8. Computational analysis of semi-span model test techniques

    NASA Technical Reports Server (NTRS)

    Milholen, William E., II; Chokani, Ndaona

    1996-01-01

    A computational investigation was conducted to support the development of a semi-span model test capability in the NASA LaRC's National Transonic Facility. This capability is required for the testing of high-lift systems at flight Reynolds numbers. A three-dimensional Navier-Stokes solver was used to compute the low-speed flow over both a full-span configuration and a semi-span configuration. The computational results were found to be in good agreement with the experimental data. The computational results indicate that the stand-off height has a strong influence on the flow over a semi-span model. The semi-span model adequately replicates the aerodynamic characteristics of the full-span configuration when a small stand-off height, approximately twice the tunnel empty sidewall boundary layer displacement thickness, is used. Several active sidewall boundary layer control techniques were examined including: upstream blowing, local jet blowing, and sidewall suction. Both upstream tangential blowing, and sidewall suction were found to minimize the separation of the sidewall boundary layer ahead of the semi-span model. The required mass flow rates are found to be practicable for testing in the NTF. For the configuration examined, the active sidewall boundary layer control techniques were found to be necessary only near the maximum lift conditions.

  9. Carbon dioxide and methane supersaturation in lakes of semi-humid/semi-arid region, Northeastern China

    NASA Astrophysics Data System (ADS)

    Wen, Zhidan; Song, Kaishan; Zhao, Ying; Jin, Xiuliang

    2016-08-01

    Understanding concentrations of carbon dioxide (CO2) and methane (CH4) in lakes is an important part of a comprehensive global carbon budget. We estimated data on the partial pressure of CO2 (pCO2) and CH4 (pCH4) from sampling with 95 lakes in semi-humid/semi-arid region of Northeastern China during ice-free period. Both pCO2 and pCH4 varied greatly among the study sites. p(CO2) values in these lakes ranged from 21.9 to 30,152.3 μatm (n = 403), and 91% of lakes in this survey were supersaturated with CO2. p(CH4) values ranged from 12.6 to 139,630.7 μatm with all sites in this study of CH4 sources to the atmosphere during the ice-free period. The collected urban lakes samples exhibited higher pCO2 and pCH4 than wild lakes samples. Either the mean value of p(CO2) or p(CH4) in saline waters is higher than in fresh waters. Correlation analysis implied that the partial pressure of the GHGs (CO2 and CH4) showed statistically correlations with water environment indicators like pH, dissolved organic carbon (DOC), total nitrogen (TN), total phosphorus (TP), and chlorophyll a (Chla). However, the most of the relationships showed a high degree of scatter, only pH might be used as the predictor of the gas partial pressure based on the result of this study (rpCO2 = -0.437, p < 0.01, n = 382; rpCH4 = -0.265, p < 0.01, n = 400). Furthermore, salinity could be a good predictor for p(CO2) and p(CH4) in 83 freshwater lakes in our study (rpCO2 = 0.365, rpCH4 = 0.323, p < 0.01, n = 348). The mean CO2 flux increased with the decreasing lake area size. The calculated annual areal carbon emission rate is 560.2 g C m-2 from 95 lakes in Northeastern China. We could not extrapolate carbon emission from these lakes to the boreal region or a wider scale because of the change of environmental conditions.

  10. Semi-solid electrodes having high rate capability

    DOEpatents

    Chiang, Yet-Ming; Duduta, Mihai; Holman, Richard; Limthongkul, Pimpa; Tan, Taison

    2015-11-10

    Embodiments described herein relate generally to electrochemical cells having high rate capability, and more particularly to devices, systems and methods of producing high capacity and high rate capability batteries having relatively thick semi-solid electrodes. In some embodiments, an electrochemical cell includes an anode, a semi-solid cathode that includes a suspension of an active material and a conductive material in a liquid electrolyte, and an ion permeable membrane disposed between the anode and the cathode. The semi-solid cathode has a thickness in the range of about 250 .mu.m-2,500 .mu.m, and the electrochemical cell has an area specific capacity of at least 5 mAh/cm.sup.2 at a C-rate of C/2.

  11. Semi-solid electrodes having high rate capability

    DOEpatents

    Chiang, Yet-Ming; Duduta, Mihai; Holman, Richard; Limthongkul, Pimpa; Tan, Taison

    2016-07-05

    Embodiments described herein relate generally to electrochemical cells having high rate capability, and more particularly to devices, systems and methods of producing high capacity and high rate capability batteries having relatively thick semi-solid electrodes. In some embodiments, an electrochemical cell includes an anode, a semi-solid cathode that includes a suspension of an active material and a conductive material in a liquid electrolyte, and an ion permeable membrane disposed between the anode and the cathode. The semi-solid cathode has a thickness in the range of about 250 .mu.m-2,500 .mu.m, and the electrochemical cell has an area specific capacity of at least 5 mAh/cm.sup.2 at a C-rate of C/2.

  12. Permittivity and permeability of semi-infinite metamaterial

    NASA Astrophysics Data System (ADS)

    Porvatkina, O. V.; Tishchenko, A. A.; Strikhanov, M. N.

    2016-08-01

    In our work we investigate dielectric and magnetic properties of semi-infinite metamaterial consisting of particles of different possible nature: atoms, molecules, nanoparticles, etc. It is important that these particles would have magnetic properties. Polarization of a near-surface layer is known to differ from its bulk value for non-magnetic materials; for magnetic materials, including metamaterials, the situation should be similar, which is the subject of our research. We obtain analogues of the Clausius-Mossotti relation both for permittivity and permeability taking into account the local field effects in the longwave approximation for semi-infinite metamaterial. These relations describe the connection between macroscopic characteristics of the semi-infinite metamaterial (permittivity and permeability) and characteristics of constituent particles (dielectric polarizability and magnetic polarizability), which is a bright example of multi-scale approach - method very popular today in physical and computer simulating.

  13. Noether's theorem for dissipative quantum dynamical semi-groups

    NASA Astrophysics Data System (ADS)

    Gough, John E.; Ratiu, Tudor S.; Smolyanov, Oleg G.

    2015-02-01

    Noether's theorem on constants of the motion of dynamical systems has recently been extended to classical dissipative systems (Markovian semi-groups) by Baez and Fong [J. Math. Phys. 54, 013301 (2013)]. We show how to extend these results to the fully quantum setting of quantum Markov dynamics. For finite-dimensional Hilbert spaces, we construct a mapping from observables to completely positive maps that leads to the natural analogue of their criterion of commutativity with the infinitesimal generator of the Markov dynamics. Using standard results on the relaxation of states to equilibrium under quantum dynamical semi-groups, we are able to characterise the constants of the motion under quantum Markov evolutions in the infinite-dimensional setting under the usual assumption of existence of a stationary strictly positive density matrix. In particular, the Noether constants are identified with the fixed point of the Heisenberg picture semi-group.

  14. An efficient semi-supervised classification approach for hyperspectral imagery

    NASA Astrophysics Data System (ADS)

    Tan, Kun; Li, Erzhu; Du, Qian; Du, Peijun

    2014-11-01

    In this paper, an efficient semi-supervised support vector machine (SVM) with segmentation-based ensemble (S2SVMSE) algorithm is proposed for hyperspectral image classification. The algorithm utilizes spatial information extracted by a segmentation algorithm for unlabeled sample selection. The unlabeled samples that are the most similar to the labeled ones are found and the candidate set of unlabeled samples to be chosen is enlarged to the corresponding image segments. To ensure the finally selected unlabeled samples be spatially widely distributed and less correlated, random selection is conducted with the flexibility of the number of unlabeled samples actually participating in semi-supervised learning. Classification is also refined through a spectral-spatial feature ensemble technique. The proposed method with very limited labeled training samples is evaluated via experiments with two real hyperspectral images, where it outperforms the fully supervised SVM and the semi-supervised version without spectral-spatial ensemble.

  15. Modeling and Design of Semi-Solid Flow Batteries

    NASA Astrophysics Data System (ADS)

    Brunini, Victor Eric

    A three-dimensional dynamic model of the recently introduced semi-solid flow battery system is developed and applied to address issues with important design and operation implications. Because of the high viscosity of semi-solid flow battery suspensions, alternative modes of operation not typically used in conventional redox flow battery systems must be explored to reduce pumping energy losses. Modeling results are presented .and compared to experimental observations to address important considerations for both stoichiometric and intermittent flow operation. The importance of active material selection, and its impact on efficient stoichiometric flow operation is discussed. Electrochemically active zone considerations relevant to intermittent flow operation of semi-solid flow batteries (or other potential electronically conductive flow battery systems) are addressed. Finally, the use of the model as a design tool for optimizing flow channel design to improve system level performance is demonstrated.(Copies available exclusively from MIT Libraries, libraries.mit.edu/docs - docs@mit.edu)

  16. Tough, processable semi-interpenetrating polymer networks from monomer reactants

    NASA Technical Reports Server (NTRS)

    Pater, Ruth H. (Inventor)

    1994-01-01

    A high temperature semi-interpenetrating polymer network (semi-IPN) was developed which had significantly improved processability, damage tolerance, and mechanical performance, when compared to the commercial Thermid materials. This simultaneous semi-IPN was prepared by mixing the monomer precursors of Thermid AL-600 (a thermoset) and NR-150B2 (a thermoplastic) and allowing the monomers to react randomly upon heating. This reaction occurs at a rate which decreases the flow and broadens the processing window. Upon heating at a higher temperature, there is an increase in flow. Because of the improved flow properties, broadened processing window and enhanced toughness, high strength polymer matrix composites, adhesives and molded articles can now be prepared from the acetylene end-capped polyimides which were previously inherently brittle and difficult to process.

  17. On fracture toughness evaluation for semi-brittle fracture

    NASA Technical Reports Server (NTRS)

    Eftis, J.; Liebowitz, H.

    1975-01-01

    The existing methods of assessing the fracture toughness of materials exhibiting semi-brittle fracture are critically reviewed. The methods concern the Crack Growth Resistance (R-curve), the Crack Opening Displacement (COD), and the J-integral. An analysis of the shortcomings of the methods described makes it possible to formulate a new definition of fracture toughness appropriate to semi-brittle fracture. An improved simple experimental method for measuring fracture toughness for semi-brittle fracture is proposed which takes into account both crack growth and plastic nonlinear effects at crack front. The proposed method is shown to be free of the theoretical and experimental discrepancies encountered in the R-curve, COD, and J-integral methods.

  18. Farming system context drives the value of deep wheat roots in semi-arid environments

    PubMed Central

    Lilley, Julianne M.; Kirkegaard, John A.

    2016-01-01

    The capture of subsoil water by wheat roots can make a valuable contribution to grain yield on deep soils. More extensive root systems can capture more water, but leave the soil in a drier state, potentially limiting water availability to subsequent crops. To evaluate the importance of these legacy effects, a long-term simulation analysis at eight sites in the semi-arid environment of Australia compared the yield of standard wheat cultivars with cultivars that were (i) modified to have root systems which extract more water at depth and/or (ii) sown earlier to increase the duration of the vegetative period and hence rooting depth. We compared simulations with and without annual resetting of soil water to investigate the legacy effects of drier subsoils related to modified root systems. Simulated mean yield benefits from modified root systems declined from 0.1–0.6 t ha−1 when annually reset, to 0–0.2 t ha−1 in the continuous simulation due to a legacy of drier soils (mean 0–32mm) at subsequent crop sowing. For continuous simulations, predicted yield benefits of >0.2 t ha−1 from more extensive root systems were rare (3–10% of years) at sites with shallow soils (<1.0 m), but occurred in 14–44% of years at sites with deeper soils (1.6–2.5 m). Earlier sowing had a larger impact than modified root systems on water uptake (14–31 vs 2–17mm) and mean yield increase (up to 0.7 vs 0–0.2 t ha−1) and the benefits occurred on deep and shallow soils and in more years (9–79 vs 3–44%). Increasing the proportion of crops in the sequence which dry the subsoil extensively has implications for the farming system productivity, and the crop sequence must be managed tactically to optimize overall system benefits. PMID:26976814

  19. Optimization of Semi-active Seat Suspension with Magnetorheological Damper

    NASA Astrophysics Data System (ADS)

    Segla, Stefan; Kajaste, J.; Keski-Honkola, P.

    The paper deals with modeling, control and optimization of semiactive seat suspension with pneumatic spring and magnetorheological damper. The main focus is on isolating vertical excitation from the cabin of a bucket-wheel excavator in order to protect the excavator driver against harmful vibration. Three different control algorithms are used to determine the desired semi-active damping force: skyhook control, balance control and combination of balance and skyhook controls. The dynamic behavior of the semi-active system is optimized using genetic algorithms. As the objective function the effective value of the seat (sprung mass) acceleration is used.

  20. The Ambulatory Semi-Poikilothermic Dog (Poikilothermic Against Cold)

    DTIC Science & Technology

    1952-06-10

    aK 12 pp a ii Abstract; Report No. 84 From Project No. 5-6/i-12-C2^ THE AMBULATORY SEt-H-POIKILOq^’jIRrac ..- DOG ; (Poikilothermic Against 13625...evaluating partial impairment of thermo-regulatory functions. _-; ’’•••, Ambulatory semi-poikilothermic dogs \\ xe pre.pared.’.i3r’selec-; tive...SEMI-POIKILOTHERMIC DOG * (Poikilothermic Against Cold) Dy Allen D. Keller, Physiologist and Henry Batsel, Physiologist with the technical

  1. Relationship between semi- and fully-device-independent protocols

    NASA Astrophysics Data System (ADS)

    Li, Hong-Wei; Mironowicz, Piotr; Pawłowski, Marcin; Yin, Zhen-Qiang; Wu, Yu-Chun; Wang, Shuang; Chen, Wei; Hu, Hong-Gang; Guo, Guang-Can; Han, Zheng-Fu

    2013-02-01

    We study the relation between semi- and fully-device-independent protocols. As a tool, we use the correspondence between Bell inequalities and dimension witnesses. We present a method for converting the former into the latter, and vice versa. This relation provides us with interesting results for both scenarios. First, we find random-number-generation protocols with higher bit rates for both the semi- and fully-device-independent cases. As a byproduct, we obtain classes of Bell inequalities and dimension witnesses. Then, we show how optimization methods used in studies on Bell inequalities can be adopted for dimension witnesses.

  2. A High Accuracy Method for Semi-supervised Information Extraction

    SciTech Connect

    Tratz, Stephen C.; Sanfilippo, Antonio P.

    2007-04-22

    Customization to specific domains of dis-course and/or user requirements is one of the greatest challenges for today’s Information Extraction (IE) systems. While demonstrably effective, both rule-based and supervised machine learning approaches to IE customization pose too high a burden on the user. Semi-supervised learning approaches may in principle offer a more resource effective solution but are still insufficiently accurate to grant realistic application. We demonstrate that this limitation can be overcome by integrating fully-supervised learning techniques within a semi-supervised IE approach, without increasing resource requirements.

  3. An Archetype Semi-Ring Fabry-Perot (SRFP) Resonator

    NASA Technical Reports Server (NTRS)

    Taghavi-Larigani, Shervin; VanZyl, Jakob

    2009-01-01

    We introduce and demonstrate the generation of a novel resonator, termed Semi-Ring Fabry-Perot (SRFP), that exhibits unique features, such as, its use of one plane mirror, allowing the SRFP to be easily fabricated as a symmetrical device. In addition to its unique features, it exhibits advantages of ring and Fabry-Perot resonators: 1) compared to a ring resonator that only allows a transmitted intensity, the Semi-Ring Fabry-Perot (SRFP) supports standing waves, allowing both a reflected and transmitted intensity; 2) the reflected light spectrum of the SRFP resonator is much narrower than similar Fabry-Perot, implying higher finesse.

  4. A semi-Markov model with memory for price changes

    NASA Astrophysics Data System (ADS)

    D'Amico, Guglielmo; Petroni, Filippo

    2011-12-01

    We study the high-frequency price dynamics of traded stocks by means of a model of returns using a semi-Markov approach. More precisely we assume that the intraday returns are described by a discrete time homogeneous semi-Markov model which depends also on a memory index. The index is introduced to take into account periods of high and low volatility in the market. First of all we derive the equations governing the process and then theoretical results are compared with empirical findings from real data. In particular we analyzed high-frequency data from the Italian stock market from 1 January 2007 until the end of December 2010.

  5. Semi-convection: What Is the Underlying Physical Context?

    NASA Astrophysics Data System (ADS)

    Noels, A.

    Stellar conditions leading to a possible semi-convective mixing are discussed in three relevant cases: (1) low-mass MS stars in which the CNO cycle takes progressively the lead over the PP chain due to the increase in temperature as core hydrogen burning proceeds, (2) massive MS stars which experience a large contribution of the radiation pressure to the total pressure, and (3) core-helium-burning stars for which the production of carbon in the core increases the opacity. A short discussion of semi-convection in terms of instability of non-radial modes follows.

  6. Path Planning for Semi-automated Simulated Robotic Neurosurgery.

    PubMed

    Hu, Danying; Gong, Yuanzheng; Hannaford, Blake; Seibel, Eric J

    2015-01-01

    This paper considers the semi-automated robotic surgical procedure for removing the brain tumor margins, where the manual operation is a tedious and time-consuming task for surgeons. We present robust path planning methods for robotic ablation of tumor residues in various shapes, which are represented in point-clouds instead of analytical geometry. Along with the path plans, corresponding metrics are also delivered to the surgeon for selecting the optimal candidate in the automated robotic ablation. The selected path plan is then executed and tested on RAVEN(™) II surgical robot platform as part of the semi-automated robotic brain tumor ablation surgery in a simulated tissue phantom.

  7. Path Planning for Semi-automated Simulated Robotic Neurosurgery

    PubMed Central

    Hu, Danying; Gong, Yuanzheng; Hannaford, Blake; Seibel, Eric J.

    2015-01-01

    This paper considers the semi-automated robotic surgical procedure for removing the brain tumor margins, where the manual operation is a tedious and time-consuming task for surgeons. We present robust path planning methods for robotic ablation of tumor residues in various shapes, which are represented in point-clouds instead of analytical geometry. Along with the path plans, corresponding metrics are also delivered to the surgeon for selecting the optimal candidate in the automated robotic ablation. The selected path plan is then executed and tested on RAVEN™ II surgical robot platform as part of the semi-automated robotic brain tumor ablation surgery in a simulated tissue phantom. PMID:26705501

  8. Variational data assimilation with a semi-Lagrangian semi-implicit global shallow-water equation model and its adjoint

    NASA Technical Reports Server (NTRS)

    Li, Y.; Navon, I. M.; Courtier, P.; Gauthier, P.

    1993-01-01

    An adjoint model is developed for variational data assimilation using the 2D semi-Lagrangian semi-implicit (SLSI) shallow-water equation global model of Bates et al. with special attention being paid to the linearization of the interpolation routines. It is demonstrated that with larger time steps the limit of the validity of the tangent linear model will be curtailed due to the interpolations, especially in regions where sharp gradients in the interpolated variables coupled with strong advective wind occur, a synoptic situation common in the high latitudes. This effect is particularly evident near the pole in the Northern Hemisphere during the winter season. Variational data assimilation experiments of 'identical twin' type with observations available only at the end of the assimilation period perform well with this adjoint model. It is confirmed that the computational efficiency of the semi-Lagrangian scheme is preserved during the minimization process, related to the variational data assimilation procedure.

  9. Analysis of intensity dependent near-bandedge absorption in semi-insulating 4H–SiC for photoconductive switch applications

    NASA Astrophysics Data System (ADS)

    Meyers, V.; Chowdhury, A. R.; Mauch, D.; Dickens, J. C.; Neuber, A. A.; Joshi, R. P.

    2017-04-01

    We report on the intensity-dependent behavior of the absorption coefficient (α) in semi-insulating 4H–SiC material. Data from as-received samples show a monotonic decrease in α with incident energy density, with a pronounced change in slope at around 10 mJ cm‑2. Annealed samples, on the other hand, exhibit an experimental trend of increasing α with intensity. Qualitative explanation of the observed behavior is presented that probes the possible role of spontaneous and stimulated emission for as-received samples. With annealing, trap related recombination is strongly reduced leading to higher carrier densities and increased free-carrier absorption with incident intensity. The role of band-filling and permittivity changes are shown to be inconsequential, while changes in internal fields could contribute to decreases in absorption.

  10. Plasmonic waves of a semi-infinite random nanocomposite

    SciTech Connect

    Moradi, Afshin

    2013-10-15

    The dispersion curves of the plasmonic waves of a semi-infinite random metal-dielectric nanocomposite, consisting of bulk metal embedded with dielectric inclusions, are presented. Two branches of p-polarized surface plasmon-polariton modes are found to exist. The possibility of experimentally observing the surface waves by attenuated total reflection is demonstrated.

  11. Soil Analysis using the semi-parametric NAA technique

    SciTech Connect

    Zamboni, C. B.; Silveira, M. A. G.; Medina, N. H.

    2007-10-26

    The semi-parametric Neutron Activation Analysis technique, using Au as a flux monitor, was applied to measure element concentrations of Br, Ca, Cl, K, Mn and Na for soil characterization. The results were compared with those using the Instrumental Neutron Activation Analysis technique and they found to be compatible. The viability, advantages, and limitations of using these two analytic methodologies are discussed.

  12. Uses of tree legumes in semi-arid regions

    SciTech Connect

    Felker, P.

    1980-01-01

    Uses of tree legumes in semi-arid and arid regions are reviewed. This review is divided into sections according to the following general use categories: fuels; human food; livestock food; to increase yields of crops grown beneath their canopies;and control of desertification. (MHR)

  13. 13 CFR 146.600 - Semi-annual compilation.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Semi-annual compilation. 146.600 Section 146.600 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION NEW RESTRICTIONS ON LOBBYING.... (c) Information that involves intelligence matters shall be reported only to the Select Committee...

  14. 13 CFR 146.600 - Semi-annual compilation.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 13 Business Credit and Assistance 1 2014-01-01 2014-01-01 false Semi-annual compilation. 146.600 Section 146.600 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION NEW RESTRICTIONS ON LOBBYING.... (c) Information that involves intelligence matters shall be reported only to the Select Committee...

  15. 13 CFR 146.600 - Semi-annual compilation.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 13 Business Credit and Assistance 1 2011-01-01 2011-01-01 false Semi-annual compilation. 146.600 Section 146.600 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION NEW RESTRICTIONS ON LOBBYING.... (c) Information that involves intelligence matters shall be reported only to the Select Committee...

  16. 13 CFR 146.600 - Semi-annual compilation.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 13 Business Credit and Assistance 1 2012-01-01 2012-01-01 false Semi-annual compilation. 146.600 Section 146.600 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION NEW RESTRICTIONS ON LOBBYING.... (c) Information that involves intelligence matters shall be reported only to the Select Committee...

  17. 13 CFR 146.600 - Semi-annual compilation.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 13 Business Credit and Assistance 1 2013-01-01 2013-01-01 false Semi-annual compilation. 146.600 Section 146.600 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION NEW RESTRICTIONS ON LOBBYING.... (c) Information that involves intelligence matters shall be reported only to the Select Committee...

  18. 22 CFR 712.600 - Semi-annual compilation.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 22 Foreign Relations 2 2011-04-01 2009-04-01 true Semi-annual compilation. 712.600 Section 712.600 Foreign Relations OVERSEAS PRIVATE INVESTMENT CORPORATION ADMINISTRATIVE PROVISIONS NEW RESTRICTIONS ON... the Committee on Foreign Relations of the Senate and the Committee on Foreign Affairs of the House...

  19. 22 CFR 712.600 - Semi-annual compilation.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 22 Foreign Relations 2 2010-04-01 2010-04-01 true Semi-annual compilation. 712.600 Section 712.600 Foreign Relations OVERSEAS PRIVATE INVESTMENT CORPORATION ADMINISTRATIVE PROVISIONS NEW RESTRICTIONS ON... the Committee on Foreign Relations of the Senate and the Committee on Foreign Affairs of the House...

  20. Sediments in Semi-arid Wetlands: US Southern High Plains

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Playas are ephemeral wetlands on the semi-arid U.S. Southern High Plains that serve as runoff catchment basins and are thought to be focal points of Ogallala aquifer recharge. Sediments in playas alter biodiversity and hydroperiods. The purpose of this study was to evaluate the effects of outerbas...

  1. 22 CFR 227.600 - Semi-annual compilation.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Senate and the Clerk of the House of Representatives a report containing a compilation of the information... 30 days after receipt of the report by the Secretary and the Clerk. (c) Information that involves... information shall not be available for public inspection. (e) The first semi-annual compilation shall...

  2. 38 CFR 45.600 - Semi-annual compilation.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... (CONTINUED) NEW RESTRICTIONS ON LOBBYING Agency Reports § 45.600 Semi-annual compilation. (a) The head of... Representatives a report containing a compilation of the information contained in the disclosure reports received... report by the Secretary and the Clerk. (c) Information that involves intelligence matters shall...

  3. 40 CFR 34.600 - Semi-annual compilation.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... NEW RESTRICTIONS ON LOBBYING Agency Reports § 34.600 Semi-annual compilation. (a) The head of each... report containing a compilation of the information contained in the disclosure reports received during... the Secretary and the Clerk. (c) Information that involves intelligence matters shall be reported...

  4. 12 CFR 411.600 - Semi-annual compilation.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Reports § 411.600 Semi-annual compilation. (a) The head of each agency shall collect and compile the... information contained in the disclosure reports received during the six-month period ending on March 31 or... public inspection 30 days after receipt of the report by the Secretary and the Clerk. (c)...

  5. 22 CFR 138.600 - Semi-annual compilation.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Senate and the Clerk of the House of Representatives a report containing a compilation of the information... 30 days after receipt of the report by the Secretary and the Clerk. (c) Information that involves... information shall not be available for public inspection. (e) The first semi-annual compilation shall...

  6. 32 CFR 28.600 - Semi-annual compilation.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... REGULATIONS NEW RESTRICTIONS ON LOBBYING Agency Reports § 28.600 Semi-annual compilation. (a) The head of each... report containing a compilation of the information contained in the disclosure reports received during... the Secretary and the Clerk. (c) Information that involves intelligence matters shall be reported...

  7. 45 CFR 93.600 - Semi-annual compilation.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... LOBBYING Agency Reports § 93.600 Semi-annual compilation. (a) The head of each agency shall collect and... compilation of the information contained in the disclosure reports received during the six-month period ending... Clerk. (c) Information that involves intelligence matters shall be reported only to the Select...

  8. 15 CFR 28.600 - Semi-annual compilation.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Agency Reports § 28.600 Semi-annual compilation. (a) The head of each agency shall collect and compile... the information contained in the disclosure reports received during the six-month period ending on.... (c) Information that involves intelligence matters shall be reported only to the Select Committee...

  9. A Semi-Batch Reactor Experiment for the Undergraduate Laboratory

    ERIC Educational Resources Information Center

    Derevjanik, Mario; Badri, Solmaz; Barat, Robert

    2011-01-01

    This experiment and analysis offer an economic yet challenging semi-batch reactor experience. Household bleach is pumped at a controlled rate into a batch reactor containing pharmaceutical hydrogen peroxide solution. Batch temperature, product molecular oxygen, and the overall change in solution conductivity are metered. The reactor simulation…

  10. Aerodynamics of Drag Reduction Devices for Semi-Trucks

    NASA Astrophysics Data System (ADS)

    Ortega, Jason; Salari, Kambiz

    2014-11-01

    An increasing number of semi-trucks throughout the United States are being retrofitted with aerodynamic drag reduction devices to improve the vehicle fuel economy. Such devices typically include both trailer skirts and boattails to mitigate trailer underbody drag and base drag, respectively. Since full-scale measurements of the device performance are especially prone to experimental noise due to the effects of the driver, route, payload, or atmospheric conditions, more precise data must be obtained within a wind tunnel. In this experimental study, the wind-averaged drag coefficient is measured for a detailed 1/8th scale semi-truck model. The Reynolds number based upon the vehicle width is 1.7e6. A number of trailer skirt and boattail device configurations are considered, as well as the effects of the boattail deflection angle. The results of this study demonstrate that a combination of a trailer skirt and boattail reduces the aerodynamic drag of a semi-truck by as much as 25%. If such a combination were applied to each of the semi-trucks throughout the United States, several billion dollars in fuel savings could be achieved each year. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344. LLNL-ABS-657810.

  11. Study of Semi-Span Model Testing Techniques

    NASA Technical Reports Server (NTRS)

    Gatlin, Gregory M.; McGhee, Robert J.

    1996-01-01

    An investigation has been conducted in the NASA Langley 14- by 22-Foot Subsonic Tunnel in order to further the development of semi-span testing capabilities. A twin engine, energy efficient transport (EET) model with a four-element wing in a takeoff configuration was used for this investigation. Initially a full span configuration was tested and force and moment data, wing and fuselage surface pressure data, and fuselage boundary layer measurements were obtained as a baseline data set. The semi-span configurations were then mounted on the wind tunnel floor, and the effects of fuselage standoff height and shape as well as the effects of the tunnel floor boundary layer height were investigated. The effectiveness of tangential blowing at the standoff/floor juncture as an active boundary-layer control technique was also studied. Results indicate that the semi-span configuration was more sensitive to variations in standoff height than to variations in floor boundary layer height. A standoff height equivalent to 30 percent of the fuselage radius resulted in better correlation with full span data than no standoff or the larger standoff configurations investigated. Undercut standoff leading edges or the use of tangential blowing in the standoff/ floor juncture improved correlation of semi-span data with full span data in the region of maximum lift coefficient.

  12. 45 CFR 604.600 - Semi-annual compilation.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 45 Public Welfare 3 2011-10-01 2011-10-01 false Semi-annual compilation. 604.600 Section 604.600 Public Welfare Regulations Relating to Public Welfare (Continued) NATIONAL SCIENCE FOUNDATION NEW..., shall be available for public inspection 30 days after receipt of the report by the Secretary and...

  13. 45 CFR 604.600 - Semi-annual compilation.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 45 Public Welfare 3 2014-10-01 2014-10-01 false Semi-annual compilation. 604.600 Section 604.600 Public Welfare Regulations Relating to Public Welfare (Continued) NATIONAL SCIENCE FOUNDATION NEW..., shall be available for public inspection 30 days after receipt of the report by the Secretary and...

  14. Concomitant information in bioassay and semi-parametric estimation.

    PubMed

    Kim, Peter T; Lee, Christine H

    2005-05-15

    This paper presents a flexible modern approach to handling concomitant information for estimating the relative potency parameter in quantitative bioassays. This is accomplished in a semi-parametric framework where the concomitant variable is included non-parametrically. Estimation is then performed using smoothing splines where the point and interval estimators of the relative potency parameter exhibits desirable asymptotic properties.

  15. Penalized Likelihood for General Semi-Parametric Regression Models.

    DTIC Science & Technology

    1985-05-01

    should be stressed that q, while it may be somewhat less than n, will still be ’large’, and parametric estimation of £ will not be appropriate...Partial spline models for the semi- parametric estimation of functions of several variables, in Statistical Analysis of Time Series, Tokyo: Institute of

  16. High compliance vascular grafts based on semi-interpenetrating networks

    PubMed Central

    Dempsey, David K.; Nezarati, Roya M.; Mackey, Calvin E.

    2014-01-01

    Current synthetic vascular grafts have poor patency rates in small diameter applications (<6 mm) due to intimal hyperplasia arising from a compliance mismatch between the graft and native vasculature. Enormous efforts have focused on improving biomechanical properties; however, polymeric grafts are often constrained by an inverse relationship between burst pressure and compliance. We have developed a new, semi-interpenetrating network (semi-IPN) approach to improve compliance without sacrificing burst pressure. The effects of heat treatment on graft morphology, fiber architecture, and resultant biomechanical properties are presented. In addition, biomechanical properties after equilibration at physiological temperature were investigated in relation to polyurethane microstructure to better predict in vivo performance. Compliance values as high as 9.2 ± 2.7 %/mmHg x 10−4 were observed for the semi-IPN graft while also maintaining high burst pressure, 1780 ± 230 mm Hg. The high compliance of these heat-treated poly(carbonate urethane) (PCU) and semi-IPN grafts is expected to improve long-term patency rates beyond even saphenous vein autografts by preventing intimal hyperplasia. The fundamental structure-property relationships gained from this work may also be utilized to advance biomedical device designs based on thermoplastic polyurethanes. PMID:25601822

  17. [Simulation on the restoration effect of soil moisture in alfalfa (Medicago sativa)-grain rotation system in semi-arid and drought-prone regions of Loess Plateau].

    PubMed

    Wang, Xue-Chun; Li, Jun; Fang, Xin-Yu; Sun, Jian; Tahir, Muhammad Naveed

    2011-01-01

    With the combination of field survey and EPIC modeling, this paper simulated the restoration effect of soil moisture in different alfalfa (Medicago sativa)-grain rotation systems in semi-arid and drought-prone regions of Loess Plateau. In perennial alfalfa field and in grain crop field after alfalfa, the correlation coefficients between the simulated and observed values of soil moisture content in 0-10 m layer were larger than 0.9 (P < 0.01), and their relative root mean square errors were between 0.05 and 0.16, with the relative errors less than 10%. The dynamic changes of the simulated soil moisture contents in different soil layers were consistent with those of the observed values. In the study regions, it was difficult for the restoration of soil moisture in the deep soil layers of alfalfa field. During the cultivation of alfalfa, the soil moisture content in the layers at 8-10 m depth should not be less than 5.7%. Considering the sustainable development of agricultural production, the appropriate cultivation duration of alfalfa should be 4-6 years and no more than 8 years. For the restoration of soil moisture after alfalfa cultivation in the study regions, the rotation system potato (Solanum tuberosum) --> potato --> spring wheat (Triticum aestivum) could be adopted, and alfalfa could be cultivated again after 32-33 years.

  18. a Proposed New Vegetation Index, the Total Ratio Vegetation Index (trvi), for Arid and Semi-Arid Regions

    NASA Astrophysics Data System (ADS)

    Fadaei, H.; Suzuki, R.; Sakai, T.; Torii, K.

    2012-07-01

    Vegetation indices that provide important key to predict amount vegetation in forest such as percentage vegetation cover, aboveground biomass, and leaf-area index. Arid and semi-arid areas are not exempt of this rule. Arid and semi-arid areas of northeast Iran cover about 3.4 million ha and are populated by two main tree species, the broadleaf Pistacia vera (pistachio) and the conifer Juniperus excelsa ssp. polycarpos (Persian juniper). Natural stands of pistachio in Iran are not only environmentally important but also genetically essential as seed sources for pistachio production in orchards. We investigated the relationships between tree density and vegetation indices in the arid and semi-arid regions in the northeast of Iran by analysing Advanced Land Observing Satellite (ALOS) data PRISM is a panchromatic radiometer with a 2.5 m spatial resolution at nadir, and has one band with a wavelength of 0.52-0.77 μm (JAXA EORC). AVNIR-2 is a visible and near infrared radiometer for observing land and coastal zones with a 10 m spatial resolution at nadir, and has four multispectral bands: blue (0.42-0.50 μm), green (0.52-0.60 μm), red (0.61-0.69 μm), and near infrared (0.76-0.89 μm) (JAXA EORC). In this study, we estimated various vegetation indices using maximum filtering algorithm (5×5) and examined. This study carried out of juniper forests and natural pistachio stand using Advanced Land Observing Satellite (ALOS) and field inventories. Have been compared linear regression model of vegetation indices and proposed new vegetation index for arid and semi-arid regions. Also, we estimated the densities of juniper forests and natural pistachio stands using remote sensing to help in the sustainable management and production of pistachio in Iran. We present a new vegetation index for arid and semi-arid regions with sparse forest cover, the Total Ratio Vegetation Index (TRVI), and we investigate the relationship of the new index to tree density by analysing data from the

  19. Development of a semi-permanent mascara technology.

    PubMed

    Dempsey, J H; Fabula, A M; Rabe, T E; Lubbers, J M; Ye, M

    2012-02-01

    Many women would like their mascara beauty benefits to be available all day, every day. One way to address this desire is through a semi-permanent mascara technology that provides full mascara benefits of long, dark beautiful lashes for multiple days. To date, products promising multi-day benefits have acted more as either 'lash dyes', providing a lash darkening benefit but failing to provide fullness and length, or waterproof mascaras that do not maintain the initial beauty look over multiple days. Here, a formulation approach is described for a mascara product that is designed to be abrasion resistant, flexible and insoluble in soap and water so that the initial beauty look is maintained for multiple days. The new semi-permanent formula technology uses rosinate polymers that have a superior combination of flexibility, abrasion resistance and water and surfactant resistance. Based on principles used by the paint industry for creating durable films, the levels of the polymers and other non-volatile ingredients are balanced such that the product forms a continuous polymer film on the eyelash. Cryo-SEM is used to demonstrate that the new semi-permanent formula technology forms a film different from those formed by current mascara products. A stretch test and rub test are used to demonstrate that the new semi-permanent formula technology has superior flexibility and abrasion resistance to current mascara products. Finally, a multi-day consumer study with daily imaging of the eyes is used to demonstrate the superior wear performance of the new semi-permanent formula technology in actual usage.

  20. Semi-annual Sq-variation in solar activity cycle

    NASA Astrophysics Data System (ADS)

    Pogrebnoy, V.; Malosiev, T.

    The peculiarities of semi-annual variation in solar activity cycle have been studied. The data from observatories having long observational series and located in different latitude zones were used. The following observatories were selected: Huancayo (magnetic equator), from 1922 to 1959; Apia (low latitudes), from 1912 to 1961; Moscow (middle latitudes), from 1947 to 1965. Based on the hourly values of H-components, the average monthly diurnal amplitudes (a difference between midday and midnight values), according to five international quiet days, were computed. Obtained results were compared with R (relative sunspot numbers) in the ranges of 0-30R, 40-100R, and 140-190R. It was shown, that the amplitude of semi-annual variation increases with R, from minimum to maximum values, on average by 45%. At equatorial Huancayo observatory, the semi-annual Sq(H)-variation appears especially clearly: its maximums take place at periods of equinoxes (March-April, September-October), and minimums -- at periods of solstices (June-July, December-January). At low (Apia observatory) and middle (Moscow observatory) latitudes, the character of semi-annual variation is somewhat different: it appears during the periods of equinoxes, but considerably less than at equator. Besides, with the growth of R, semi-annual variation appears against a background of annual variation, in the form of second peaks (maximum in June). At observatories located in low and middle latitudes, second peaks become more appreciable with an increase of R (March-April and September-October). During the periods of low solar activity, they are insignificant. This work has been carried out with the support from International Scientific and Technology Center (Project #KR-214).

  1. White matter hyperintensities segmentation: a new semi-automated method.

    PubMed

    Iorio, Mariangela; Spalletta, Gianfranco; Chiapponi, Chiara; Luccichenti, Giacomo; Cacciari, Claudia; Orfei, Maria D; Caltagirone, Carlo; Piras, Fabrizio

    2013-01-01

    White matter hyperintensities (WMH) are brain areas of increased signal on T2-weighted or fluid-attenuated inverse recovery magnetic resonance imaging (MRI) scans. In this study we present a new semi-automated method to measure WMH load that is based on the segmentation of the intensity histogram of fluid-attenuated inversion recovery images. Thirty patients with mild cognitive impairment with variable WMH load were enrolled. The semi-automated WMH segmentation included removal of non-brain tissue, spatial normalization, removal of cerebellum and brain stem, spatial filtering, thresholding to segment probable WMH, manual editing for correction of false positives and negatives, generation of WMH map, and volumetric estimation of the WMH load. Accuracy was quantitatively evaluated by comparing semi-automated and manual WMH segmentations performed by two independent raters. Differences between the two procedures were assessed using Student's t-tests and similarity was evaluated using linear regression model and Dice similarity coefficient (DSC). The volumes of the manual and semi-automated segmentations did not statistically differ (t-value = -1.79, DF = 29, p = 0.839 for rater 1; t-value = 1.113, DF = 29, p = 0.2749 for rater 2), were highly correlated [R (2) = 0.921, F (1,29) = 155.54, p < 0.0001 for rater 1; R (2) = 0.935, F (1,29) = 402.709, p < 0.0001 for rater 2] and showed a very strong spatial similarity (mean DSC = 0.78, for rater 1 and 0.77 for rater 2). In conclusion, our semi-automated method to measure the load of WMH is highly reliable and could represent a good tool that could be easily implemented in routinely neuroimaging analyses to map clinical consequences of WMH.

  2. Climate warming threatens semi-arid forests in Inner Asia

    NASA Astrophysics Data System (ADS)

    WU, X.

    2015-12-01

    A line of evidences reveal an increasing tree growth decline and tree mortality mainly attributable to climate warming and the warming-mediated changes in drought and other processes in many parts of world tropical, temperate and boreal forests. However, the growth responses to climate change of the widely distributed semi-arid forests are unclear. Here, we synthetically investigate the tree growth patterns during past decades and its interannual response to climate variations in Inner Asia combining the ground truth field survey and samplings, remote sensing observations and climate data. We identified a pervasive tree growth decline since mid-1990s in semi-arid forests in Inner Asia. The widely observed tree growth decline is dominantly attributable to warming-induced water stress during pre- and early growing season. Tree growth of semi-arid forests in Inner Asia is particularly susceptible to spring warming and has been suffering a prolonged growth limitation in recent decades due to spring warming-mediated water conditions. Additionally, we identified a much slower growth rate in younger trees and a lack of tree regeneration in these semi-arid forests. The widely observed forest growth reduction and lack of tree regeneration over semi-arid forests in Inner Asia could predictably exert great effects on forest structure, regionally/globally biophysical and biochemical processes and the feedbacks between biosphere and atmosphere. Notably, further increases in forest stress and tree mortality could be reasonably expected, especially in context of the increase frequency and severity of high temperature and heat waves and changes in forest disturbances, potentially driving the eventual regional loss of current semi-arid forests. Given the potential risks of climate induced forest dieback, increased management attention to adaptation options for enhancing forest resistance and resilience to projected climate stress can be expected. However, the functionally realistic

  3. 40 CFR 430.60 - Applicability; description of the semi-chemical subcategory.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...-chemical subcategory. 430.60 Section 430.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...-Chemical Subcategory § 430.60 Applicability; description of the semi-chemical subcategory. The provisions... paper at semi-chemical mills....

  4. 40 CFR 430.60 - Applicability; description of the semi-chemical subcategory.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...-chemical subcategory. 430.60 Section 430.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...-Chemical Subcategory § 430.60 Applicability; description of the semi-chemical subcategory. The provisions... paper at semi-chemical mills....

  5. A generic approach to improved semi-solid forming of metals

    SciTech Connect

    Klier, E. M.

    2002-06-05

    Lack of technology for the production of large inexpensive feedstock, with uniform spherical primary phase throughout as required for semi-solid forming, has restricted realization of the full potential for the semi-solid forming process. Furthermore, narrow process windows and alloy chemistry restrictions increase process costs and limit performance attributes possible with existing semi-solid metal systems. Successful semi-solid forming trials utilizing Chesapeake Composites Corporation's DSC trademark Metals for feedstock indicate that this represents a generic approach to providing a permanent highly uniform, spherical solid phase, without electromagnetic or mechanical shearing. This approach also provides for further growth of semi-solid forming by providing for: low cost large diameter billet stock, reduced semi-solid forming costs, extension of semi-solid forming to new alloy systems, and semi-solid formed components with substantially enhanced physical and mechanical proper ties.

  6. How is Gaia Doing at L+10m?

    NASA Astrophysics Data System (ADS)

    Lammers, U.; O'Mullane, W.

    2015-09-01

    ESA's 1000-Million star surveyor Gaia was launched past December from French Guiana. Following a perfect launch towards L2 is has been commissioned over the early months and entered into the nominal mission phase planned to last 5 years. We describe the status of the space and ground segment with emphasis on the complex distributed data processing system designed to keep up with the several 10s of GB of telemetry streaming in every day. Apart from the near-real-time processing a second tier of systems will soon shift into the focus. After years of validation with simulation data these cyclic processes are slowly being bootstrapped with real flight data and readied to produce the first public catalog scheduled for L+31m.

  7. State reduction for semi-Markov reliability models

    NASA Technical Reports Server (NTRS)

    White, Allan L.; Palumbo, Daniel L.

    1990-01-01

    Trimming, a method of reducing the number of states in a semi-Markov reliability model, is described, and an error bound is derived. The error bound uses only three parameters from the semi-Markov model: (1) the maximum sum of rates for failure transitions leaving any state, (2) the maximum average holding time for a recovery-mode state, (3) and the operating time for the system. The error bound can be computed before any model generation takes places, which means the modeler can decide immediately whether the model can be trimmed. The trimming has a precise and simple description and thus can be easily included in a program that generates reliability models. The simplest version of the error bound for trimming is presented. More accurate versions can be obtained by requesting more information about the system being modeled.

  8. Gel Point Determination of Biopolymer Based Semi-IPN Hydrogels

    NASA Astrophysics Data System (ADS)

    Choudhary, Soumitra; Bhatia, Surita R.

    2008-07-01

    Water-based semi-IPNs (Interpenetrating Polymer Networks) were prepared by mixing two biopolymers, alginate and hydrophobically modified ethylhydroxy ethyl cellulose (HMEHEC), followed by crosslinking the alginate by in-situ release of calcium ions. By altering two different parameters, molecular weight of HMEHEC and calcium crosslinker concentration, we were able to fine tune the rheological properties of the semi-IPNs. Rheological studies in the linear viscoelastic region indicate storage moduli comparable to soft tissue for hydrogels having 90 wt% water. The system is found to be stable over a prolonged period of time, i.e. no phase separation is observed. Uniformity of the structure is confirmed by monotonic behavior of the intensity-q slope in SAXS and SANS over the entire length scale.

  9. Semi-inclusive hadronic B decays in the endpoint region

    SciTech Connect

    Chay, Junegone; Kim, Chul; Leibovich, Adam K.; Zupan, Jure

    2006-10-01

    We consider in the soft-collinear effective theory semi-inclusive hadronic B decays, B{yields}XM, in which an energetic light meson M near the endpoint recoils against an inclusive jet X. We focus on a subset of decays where the spectator quark from the B meson ends up in the jet. The branching ratios and direct CP asymmetries are computed to next-to-leading order accuracy in {alpha}{sub s} and to leading order in 1/m{sub b}. The contribution of charming penguins is extensively discussed, and a method to extract it in semi-inclusive decays is suggested. Subleading 1/m{sub b} corrections and SU(3) breaking effects are discussed.

  10. Slow domains in semi-insulating GaAs

    SciTech Connect

    Neumann, A.

    2001-07-01

    Semi-insulating GaAs shows current oscillations if a high dc voltage is applied to a sample. These oscillations are caused by traveling high-electric-field domains that are formed as a result of electric-field-enhanced electron trapping. This article describes the various types of experiments that have been carried out with this system, including recent ones that use the electro-optic Pockels effect in order to measure the local electric fields in the sample in a highly accurate manner. An historical overview of the theoretical developments is given and shows that no satisfying theory is currently available. A list of all the required ingredients for a successful theory is provided and the experimental data are explained in a qualitative manner. Furthermore, the main electron trap in semi-insulating GaAs is the native defect EL2, the main properties of which are described. {copyright} 2001 American Institute of Physics.

  11. Semi-analytic valuation of stock loans with finite maturity

    NASA Astrophysics Data System (ADS)

    Lu, Xiaoping; Putri, Endah R. M.

    2015-10-01

    In this paper we study stock loans of finite maturity with different dividend distributions semi-analytically using the analytical approximation method in Zhu (2006). Stock loan partial differential equations (PDEs) are established under Black-Scholes framework. Laplace transform method is used to solve the PDEs. Optimal exit price and stock loan value are obtained in Laplace space. Values in the original time space are recovered by numerical Laplace inversion. To demonstrate the efficiency and accuracy of our semi-analytic method several examples are presented, the results are compared with those calculated using existing methods. We also present a calculation of fair service fee charged by the lender for different loan parameters.

  12. Semi-automatic volumetrics system to parcellate ROI on neocortex

    NASA Astrophysics Data System (ADS)

    Tan, Ou; Ichimiya, Tetsuya; Yasuno, Fumihiko; Suhara, Tetsuya

    2002-05-01

    A template-based and semi-automatic volumetrics system--BrainVol is build to divide the any given patient brain to neo-cortical and sub-cortical regions. The standard region is given as standard ROI drawn on a standard brain volume. After normalization between the standard MR image and the patient MR image, the sub-cortical ROIs' boundary are refined based on gray matter. The neo-cortical ROIs are refined by sulcus information that is semi-automatically marked on the patient brain. Then the segmentation is applied to 4D PET image of same patient for calculation of TAC (Time Activity Curve) by co-registration between MR and PET.

  13. Direct process for preparing semi-crystalline polyimides

    NASA Technical Reports Server (NTRS)

    Chang, Alice C. (Inventor); St. Clair, Terry L. (Inventor)

    1995-01-01

    The invention is a direct process for preparing semi-crystalline polyimides. This process comprises the steps of: providing a polar aprotic solvent, adding a dianhydride and a diamine to the solvent to form a mixture, stirring the mixture at ambient temperature, and adding glacial acetic acid to the mixture to provide a ratio of polar aprotic solvent to glacial acetic acid which ranges from about 90 to 10 to about 75 to 25 by volume to form a solution. The solution was heated to a range from about 110.degree. C. to about 140.degree. C. to form a polyimide precipitate. The polyimide precipitate was recovered as a semi-crystalline polyimide powder.

  14. Semi-parametric estimation in failure time mixture models.

    PubMed

    Taylor, J M

    1995-09-01

    A mixture model is an attractive approach for analyzing failure time data in which there are thought to be two groups of subjects, those who could eventually develop the endpoint and those who could not develop the endpoint. The proposed model is a semi-parametric generalization of the mixture model of Farewell (1982). A logistic regression model is proposed for the incidence part of the model, and a Kaplan-Meier type approach is used to estimate the latency part of the model. The estimator arises naturally out of the EM algorithm approach for fitting failure time mixture models as described by Larson and Dinse (1985). The procedure is applied to some experimental data from radiation biology and is evaluated in a Monte Carlo simulation study. The simulation study suggests the semi-parametric procedure is almost as efficient as the correct fully parametric procedure for estimating the regression coefficient in the incidence, but less efficient for estimating the latency distribution.

  15. Semi-quantitative spectrographic analysis and rank correlation in geochemistry

    USGS Publications Warehouse

    Flanagan, F.J.

    1957-01-01

    The rank correlation coefficient, rs, which involves less computation than the product-moment correlation coefficient, r, can be used to indicate the degree of relationship between two elements. The method is applicable in situations where the assumptions underlying normal distribution correlation theory may not be satisfied. Semi-quantitative spectrographic analyses which are reported as grouped or partly ranked data can be used to calculate rank correlations between elements. ?? 1957.

  16. Semi-Classical Dirac Vacuum Polarisation in a Scalar Field

    NASA Astrophysics Data System (ADS)

    Lampart, Jonas; Lewin, Mathieu

    2016-08-01

    We study vacuum polarisation effects of a Dirac field coupled to an external scalar field and derive a semi-classical expansion of the regu-larised vacuum energy. The leading order of this expansion is given by a classical formula due to Chin, Lee-Wick and Walecka, for which our result provides the first rigorous proof. We then discuss applications to the non-relativistic large-coupling limit of an interacting system, and to the stability of homogeneous systems.

  17. The semi-Markov unreliability range evaluator program

    NASA Technical Reports Server (NTRS)

    Butler, R. W.

    1984-01-01

    The SURE program is a design/validation tool for ultrareliable computer system architectures. The system uses simple algebraic formulas to compute accurate upper and lower bounds for the death state probabilities of a large class of semi-Markov models. The mathematical formulas used in the program were derived from a mathematical theorem proven by Allan White under contract to NASA Langley Research Center. This mathematical theorem is discussed along with the user interface to the SURE program.

  18. A semi-Lagrangian approach to the shallow water equation

    NASA Technical Reports Server (NTRS)

    Bates, J. R.; Mccormick, Stephen F.; Ruge, John; Sholl, David S.; Yavneh, Irad

    1993-01-01

    We present a formulation of the shallow water equations that emphasizes the conservation of potential vorticity. A locally conservative semi-Lagrangian time-stepping scheme is developed, which leads to a system of three coupled PDE's to be solved at each time level. We describe a smoothing analysis of these equations, on which an effective multigrid solver is constructed. Some results from applying this solver to the static version of these equations are presented.

  19. Hyperbolic and semi-parametric models in finance

    NASA Astrophysics Data System (ADS)

    Bingham, N. H.; Kiesel, Rüdiger

    2001-02-01

    The benchmark Black-Scholes-Merton model of mathematical finance is parametric, based on the normal/Gaussian distribution. Its principal parametric competitor, the hyperbolic model of Barndorff-Nielsen, Eberlein and others, is briefly discussed. Our main theme is the use of semi-parametric models, incorporating the mean vector and covariance matrix as in the Markowitz approach, plus a non-parametric part, a scalar function incorporating features such as tail-decay. Implementation is also briefly discussed.

  20. Experimental studies on semi active suspension systems with various dampers

    NASA Astrophysics Data System (ADS)

    Kumar, B. Anil; Bharath Raj, Ch; Rajendar, K.

    2015-12-01

    Some results of an experimental probe on semi Active suspension systems with various Dampers have been studied in the present paper. Dampers with different configurations were studied by using Magneto Rheological gel Damper. A comparison have been done for different configurations of Dampers viz.MR gel Damper with Magnetic field, MR gel Damper without magnetic field, Damper with conventional oil, Natural vibration without damper.

  1. Characterisation of semi-insulating GaAs

    NASA Technical Reports Server (NTRS)

    Walukiewicz, W.; Pawlowicz, L.; Lagowski, J.; Gatos, H. C.

    1982-01-01

    Hole and electron mobilities as functions of temperature and ionised impurity concentration are calculated for GaAs. It is shown that these calculations, when used to analyse electrical properties of semi-insulating GaAs, enable an assessment of the Fermi energy position and ionised impurity concentration to be made. In contrast to previous work, the analysis does not require any phenomenological assumptions.

  2. Jet substructure using semi-inclusive jet functions in SCET

    NASA Astrophysics Data System (ADS)

    Kang, Zhong-Bo; Ringer, Felix; Vitev, Ivan

    2016-11-01

    We propose a new method to evaluate jet substructure observables in inclusive jet measurements, based upon semi-inclusive jet functions in the framework of Soft Collinear Effective Theory (SCET). As a first example, we consider the jet fragmentation function, where a hadron h is identified inside a fully reconstructed jet. We introduce a new semi-inclusive fragmenting jet function {{G}}_i^h(z={ω}_J/ω, {z}_h={ω}_h/{ω}_J,{ω}_J,R,μ ) , which depends on the jet radius R and the large light-cone momenta of the parton ` i' initiating the jet ( ω), the jet ( ω J ), and the hadron h ( ω h ). The jet fragmentation function can then be expressed as a semi-inclusive observable, in the spirit of actual experimental measurements, rather than as an exclusive one. We demonstrate the consistency of the effective field theory treatment and standard perturbative QCD calculations of this observable at next-to-leading order (NLO). The renormalization group (RG) equation for the semi-inclusive fragmenting jet function {{G}}_i^h(z,{z}_h,{ω}_J,R,μ ) are also derived and shown to follow exactly the usual timelike DGLAP evolution equations for fragmentation functions. The newly obtained RG equations can be used to perform the resummation of single logarithms of the jet radius parameter R up to next-to-leading logarithmic (NLL R ) accuracy. In combination with the fixed NLO calculation, we obtain NLO+NLL R results for the hadron distribution inside the jet. We present numerical results for pp → (jet h) X in the new framework, and find excellent agreement with existing LHC experimental data.

  3. A Semi-Implicit Lattice Method for Simulating Flow

    SciTech Connect

    Rector, David R.; Stewart, Mark L.

    2010-09-20

    We propose a new semi-implicit lattice numerical method for modeling fluid flow that depends only on local primitive variable information (density, pressure, velocity) and not on relaxed upstream distribution function values. This method has the potential for reducing parallel communication and permitting larger time steps compared to the lattice Boltzmann method. The lid-driven cavity is modeled to demonstrate the accuracy of the method.

  4. Exactly energy conserving semi-implicit particle in cell formulation

    NASA Astrophysics Data System (ADS)

    Lapenta, Giovanni

    2017-04-01

    We report a new particle in cell (PIC) method based on the semi-implicit approach. The novelty of the new method is that unlike any of its semi-implicit predecessors at the same time it retains the explicit computational cycle and conserves energy exactly. Recent research has presented fully implicit methods where energy conservation is obtained as part of a non-linear iteration procedure. The new method (referred to as Energy Conserving Semi-Implicit Method, ECSIM), instead, does not require any non-linear iteration and its computational cycle is similar to that of explicit PIC. The properties of the new method are: i) it conserves energy exactly to round-off for any time step or grid spacing; ii) it is unconditionally stable in time, freeing the user from the need to resolve the electron plasma frequency and allowing the user to select any desired time step; iii) it eliminates the constraint of the finite grid instability, allowing the user to select any desired resolution without being forced to resolve the Debye length; iv) the particle mover has a computational complexity identical to that of the explicit PIC, only the field solver has an increased computational cost. The new ECSIM is tested in a number of benchmarks where accuracy and computational performance are tested.

  5. Semi-supervised learning for ordinal Kernel Discriminant Analysis.

    PubMed

    Pérez-Ortiz, M; Gutiérrez, P A; Carbonero-Ruz, M; Hervás-Martínez, C

    2016-12-01

    Ordinal classification considers those classification problems where the labels of the variable to predict follow a given order. Naturally, labelled data is scarce or difficult to obtain in this type of problems because, in many cases, ordinal labels are given by a user or expert (e.g. in recommendation systems). Firstly, this paper develops a new strategy for ordinal classification where both labelled and unlabelled data are used in the model construction step (a scheme which is referred to as semi-supervised learning). More specifically, the ordinal version of kernel discriminant learning is extended for this setting considering the neighbourhood information of unlabelled data, which is proposed to be computed in the feature space induced by the kernel function. Secondly, a new method for semi-supervised kernel learning is devised in the context of ordinal classification, which is combined with our developed classification strategy to optimise the kernel parameters. The experiments conducted compare 6 different approaches for semi-supervised learning in the context of ordinal classification in a battery of 30 datasets, showing (1) the good synergy of the ordinal version of discriminant analysis and the use of unlabelled data and (2) the advantage of computing distances in the feature space induced by the kernel function.

  6. Energy minimization mechanisms of semi-coherent interfaces

    SciTech Connect

    Shao, Shuai; Wang, J.; Misra, Amit

    2014-07-14

    In this article, we discussed energy minimization mechanisms of semi-coherent interfaces based on atomistic simulations and dislocation theory. For example, of (111) interfaces between two face centered cubic (FCC) crystals, interface comprises of two stable structures (normal FCC stacking structure and intrinsic stacking fault structure), misfit dislocations, and misfit dislocation intersections or nodes (corresponding to the high energy stacking fault (HESF) structure). According to atomistic simulations of four interfaces, we found that (1) greater spacing between misfit dislocations and/or larger slopes of generalized stacking fault energy at the stable interface structures leads to a narrower dislocation core and a higher state of coherency in the stable interfaces; (2) the HESF region is relaxed by the relative rotation and dilation/compression of the two crystals at the node. The crystal rotation is responsible for the spiral feature at the vicinity of a node and the dilation/compression is responsible for the creation of the free volume at a node; (3) the spiral feature is gradually frail and the free volume decreases with decreasing misfit dislocation spacing, which corresponds to an increase in lattice mismatch and/or a decrease in lattice rotation. Finally, the analysis method and energy minimization mechanisms explored in FCC (111) semi-coherent interfaces are also applicable for other semi-coherent interfaces.

  7. Semi-supervised SVM for individual tree crown species classification

    NASA Astrophysics Data System (ADS)

    Dalponte, Michele; Ene, Liviu Theodor; Marconcini, Mattia; Gobakken, Terje; Næsset, Erik

    2015-12-01

    In this paper a novel semi-supervised SVM classifier is presented, specifically developed for tree species classification at individual tree crown (ITC) level. In ITC tree species classification, all the pixels belonging to an ITC should have the same label. This assumption is used in the learning of the proposed semi-supervised SVM classifier (ITC-S3VM). This method exploits the information contained in the unlabeled ITC samples in order to improve the classification accuracy of a standard SVM. The ITC-S3VM method can be easily implemented using freely available software libraries. The datasets used in this study include hyperspectral imagery and laser scanning data acquired over two boreal forest areas characterized by the presence of three information classes (Pine, Spruce, and Broadleaves). The experimental results quantify the effectiveness of the proposed approach, which provides classification accuracies significantly higher (from 2% to above 27%) than those obtained by the standard supervised SVM and by a state-of-the-art semi-supervised SVM (S3VM). Particularly, by reducing the number of training samples (i.e. from 100% to 25%, and from 100% to 5% for the two datasets, respectively) the proposed method still exhibits results comparable to the ones of a supervised SVM trained with the full available training set. This property of the method makes it particularly suitable for practical forest inventory applications in which collection of in situ information can be very expensive both in terms of cost and time.

  8. Single file diffusion into a semi-infinite tube

    NASA Astrophysics Data System (ADS)

    Farrell, Spencer G.; Brown, Aidan I.; Rutenberg, Andrew D.

    2015-12-01

    We investigate single file diffusion (SFD) of large particles entering a semi-infinite tube, such as luminal diffusion of proteins into microtubules or flagella. While single-file effects have no impact on the evolution of particle density, we report significant single-file effects for individually tracked tracer particle motion. Both exact and approximate ordering statistics of particles entering semi-infinite tubes agree well with our stochastic simulations. Considering initially empty semi-infinite tubes, with particles entering at one end starting from an initial time t = 0, tracked particles are initially super-diffusive after entering the system, but asymptotically diffusive at later times. For finite time intervals, the ratio of the net displacement of individual single-file particles to the average displacement of untracked particles is reduced at early times and enhanced at later times. When each particle is numbered, from the first to enter (n = 1) to the most recent (n = N), we find good scaling collapse of this distance ratio for all n. Experimental techniques that track individual particles, or local groups of particles, such as photo-activation or photobleaching of fluorescently tagged proteins, should be able to observe these single-file effects. However, biological phenomena that depend on local concentration, such as flagellar extension or luminal enzymatic activity, should not exhibit single-file effects.

  9. Issues in offshore platform research - Part 1: Semi-submersibles

    NASA Astrophysics Data System (ADS)

    Sharma, R.; Kim, Tae-Wan; Sha, O. P.; Misra, S. C.

    2010-09-01

    Availability of economic and efficient energy resources is crucial to a nation's development. Because of their low cost and advancement in drilling and exploration technologies, oil and gas based energy systems are the most widely used energy source throughout the world. The inexpensive oil and gas based energy systems are used for everything, i.e., from transportation of goods and people to the harvesting of crops for food. As the energy demand continues to rise, there is strong need for inexpensive energy solutions. An offshore platform is a large structure that is used to house workers and machinery needed to drill wells in the ocean bed, extract oil and/or natural gas, process the produced fluids, and ship or pipe them to shore. Depending on the circumstances, the offshore platform can be fixed (to the ocean floor) or can consist of an artificial island or can float. Semi-submersibles are used for various purposes in offshore and marine engineering, e.g. crane vessels, drilling vessels, tourist vessels, production platforms and accommodation facilities, etc. The challenges of deepwater drilling have further motivated the researchers to design optimum choices for semi-submersibles for a chosen operating depth. In our series of eight papers, we discuss the design and production aspects of all the types of offshore platforms. In the present part I, we present an introduction and critical analysis of semi-submersibles.

  10. Semi-supervised dimensionality reduction using estimated class membership probabilities

    NASA Astrophysics Data System (ADS)

    Li, Wei; Ruan, Qiuqi; Wan, Jun

    2012-10-01

    In solving pattern-recognition tasks with partially labeled training data, the semi-supervised dimensionality reduction method, which considers both labeled and unlabeled data, is preferable for improving the classification and generalization capability of the testing data. Among such techniques, graph-based semi-supervised learning methods have attracted a lot of attention due to their appealing properties in discovering discriminative structure and geometric structure of data points. Although they have achieved remarkable success, they cannot promise good performance when the size of the labeled data set is small, as a result of inaccurate class matrix variance approximated by insufficient labeled training data. In this paper, we tackle this problem by combining class membership probabilities estimated from unlabeled data and ground-truth class information associated with labeled data to more precisely characterize the class distribution. Therefore, it is expected to enhance performance in classification tasks. We refer to this approach as probabilistic semi-supervised discriminant analysis (PSDA). The proposed PSDA is applied to face and facial expression recognition tasks and is evaluated using the ORL, Extended Yale B, and CMU PIE face databases and the Cohn-Kanade facial expression database. The promising experimental results demonstrate the effectiveness of our proposed method.

  11. Semi-supervised classification via local spline regression.

    PubMed

    Xiang, Shiming; Nie, Feiping; Zhang, Changshui

    2010-11-01

    This paper presents local spline regression for semi-supervised classification. The core idea in our approach is to introduce splines developed in Sobolev space to map the data points directly to be class labels. The spline is composed of polynomials and Green's functions. It is smooth, nonlinear, and able to interpolate the scattered data points with high accuracy. Specifically, in each neighborhood, an optimal spline is estimated via regularized least squares regression. With this spline, each of the neighboring data points is mapped to be a class label. Then, the regularized loss is evaluated and further formulated in terms of class label vector. Finally, all of the losses evaluated in local neighborhoods are accumulated together to measure the global consistency on the labeled and unlabeled data. To achieve the goal of semi-supervised classification, an objective function is constructed by combining together the global loss of the local spline regressions and the squared errors of the class labels of the labeled data. In this way, a transductive classification algorithm is developed in which a globally optimal classification can be finally obtained. In the semi-supervised learning setting, the proposed algorithm is analyzed and addressed into the Laplacian regularization framework. Comparative classification experiments on many public data sets and applications to interactive image segmentation and image matting illustrate the validity of our method.

  12. Experimental landfill caps for semi-arid and arid climates.

    PubMed

    Blight, Geoffrey E; Fourie, Andries B

    2005-04-01

    The United States EPA Subtitle D municipal solid waste landfill requirements specify that the permeability of a cap to a landfill be no greater than the permeability of the underliner. In recent years the concept of the evapotranspirative (ET) cap has been developed in which the cap is designed to store all rain infiltration and re-evapotranspire it during dry weather. Concern at the long period required for landfilled municipal solid waste to decompose and stabilize in arid and semi-arid climates has led to an extension of the concept of the ET cap. With the infiltrate-stabilize-evapotranspire (ISE) cap, rain infiltration during wet weather is permitted to enter the underlying waste, thus accelerating the decomposition and stabilization process. Excess infiltration is then removed from both waste and cap by evaporation during dry weather. The paper describes the construction and operation of two sets of experimental ISE caps, one in a winter rainfall semi-arid climate, and the other in a summer rainfall semi-arid climate. Observation of the rainfall, soil evaporation and amount of water stored in the caps has allowed water balances to be constructed for caps of various thicknesses. These observations show that the ISE concept is viable. In the limit, when there is insufficient rainfall to infiltrate the waste, an ISE cap operates as an ET cap.

  13. Multi-image semi-global matching in object space

    NASA Astrophysics Data System (ADS)

    Bethmann, F.; Luhmann, T.

    2015-05-01

    Semi-Global Matching (SGM) is a widespread algorithm for image matching which is used for very different applications, ranging from real-time applications (e.g. for generating 3D data for driver assistance systems) to aerial image matching. Originally developed for stereo-image matching, several extensions have been proposed to use more than two images within the matching process (multi-baseline matching, multi-view stereo). These extensions still perform the image matching in (rectified) stereo images and combine the pairwise results afterwards to create the final solution. This paper proposes an alternative approach which is suitable for the introduction of an arbitrary number of images into the matching process and utilizes image matching by using non-rectified images. The new method differs from the original SGM method mainly in two aspects: Firstly, the cost calculation is formulated in object space within a dense voxel raster by using the grey (or colour) values of all images instead of pairwise cost calculation in image space. Secondly, the semi-global (path-wise) minimization process is transferred into object space as well, so that the result of semi-global optimization leads to index maps (instead of disparity maps) which directly indicate the 3D positions of the best matches. Altogether, this yields to an essential simplification of the matching process compared to multi-view stereo (MVS) approaches. After a description of the new method, results achieved from two different datasets (close-range and aerial) are presented and discussed.

  14. Damage characterization for particles filled semi-crystalline polymer

    NASA Astrophysics Data System (ADS)

    Lauro, Franck; Balieu, Romain; Bennani, Bruno; Haugou, Gregory; Bourel, Benjamin; Chaari, Fahmi; Matsumoto, Tsukatada; Mottola, Ernesto

    2015-09-01

    Damage evolution and characterization in semi-crystalline polymer filled with particles under various loadings is still a challenge. A specific damage characterization method using Digital Image Correlation is proposed for a wide range of strain rates considering tensile tests with hydraulic jacks as well as Hopkinson's bars. This damage measurement is obtained by using and adapting the SEE method [1] which was developed to characterize the behaviour laws at constant strain rates of polymeric materials in dynamic. To validate the characterization process, various damage measurement techniques are used under quasi-static conditions before to apply the procedure in dynamic. So, the well-known damage characterization by loss of stiffness technique under quasi-static loading is applied to a polypropylene. In addition, an in-situ tensile test, carried out in a microtomograph, is used to observe the cavitation phenomenon in real time. A good correlation is obtained between all these techniques and consequently the proposed technique is supposed suitable for measuring the ductile damage observed in semi-crystalline polymers under dynamic loading. By applying it to the semi-crystalline polymer at moderate and high speed loadings, the damage evolution is measured and it is observed that the damage evolution is not strain rate dependent but the failure strain on the contrary is strain rate dependent.

  15. Biogas by semi-continuous anaerobic digestion of food waste.

    PubMed

    Zhang, Cunsheng; Su, Haijia; Wang, Zhenbin; Tan, Tianwei; Qin, Peiyong

    2015-04-01

    The semi-continuous anaerobic digestion of food waste was investigated in 1-L and 20-L continuously stirred tank reactors (CSTRs), to identify the optimum operation condition and the methane production of the semi-continuous anaerobic process. Results from a 1-L digester indicated that the optimum organic loading rate (OLR) for semi-continuous digestion is 8 g VS/L/day. The corresponding methane yield and chemical oxygen demand (COD) reduction were 385 mL/g VS and 80.2 %, respectively. Anaerobic digestion was inhibited at high OLRs (12 and 16 g VS/L/day), due to volatile fatty acid (VFA) accumulation. Results from a 20-L digester indicated that a higher methane yield of 423 mL/g VS was obtained at this larger scale. The analysis showed that the methane production at the optimum OLR fitted well with the determined kinetics equation. An obvious decrease on the methane content was observed at the initial of digestion. The increased metabolization of microbes and the activity decrease of methanogen caused by VFA accumulation explained the lower methane content at the initial of digestion.

  16. Semi-coherent time of arrival estimation using regression.

    PubMed

    Apartsin, Alexander; Cooper, Leon N; Intrator, Nathan

    2012-08-01

    Time of arrival (ToA) estimation is essential for many types of remote sensing applications including radar, sonar, and underground exploration. The standard method for ToA estimation employs a matched filter for computing the maximum likelihood estimator (MLE) for ToA. The accuracy of the MLE decreases rapidly whenever the amount of noise in a received signal rises above a certain threshold. This well-known threshold effect is unavoidable in several important applications due to various limitations on the power and the spectrum of a narrowband source pulse. A measurement performed in the presence of the threshold effect employs a receiver which operates in the semi-coherent state. Therefore, the conventional methods assuming a coherent state receiver should be adapted to the semi-coherent case. In this paper, a biosonar-inspired method for the semi-coherent ToA estimation is described. The method abandons the exploration of an echo signal by a single matched filter in favor of the analysis by multiple phase-shifted unmatched filters. Each phase-shifted unmatched filter gives rise to a biased ToA estimator. The described method uses regression for combining these estimators into a single unbiased ToA estimator that outperform the MLE in the presence of the threshold effect.

  17. Single file diffusion into a semi-infinite tube.

    PubMed

    Farrell, Spencer G; Brown, Aidan I; Rutenberg, Andrew D

    2015-11-23

    We investigate single file diffusion (SFD) of large particles entering a semi-infinite tube, such as luminal diffusion of proteins into microtubules or flagella. While single-file effects have no impact on the evolution of particle density, we report significant single-file effects for individually tracked tracer particle motion. Both exact and approximate ordering statistics of particles entering semi-infinite tubes agree well with our stochastic simulations. Considering initially empty semi-infinite tubes, with particles entering at one end starting from an initial time t = 0, tracked particles are initially super-diffusive after entering the system, but asymptotically diffusive at later times. For finite time intervals, the ratio of the net displacement of individual single-file particles to the average displacement of untracked particles is reduced at early times and enhanced at later times. When each particle is numbered, from the first to enter (n = 1) to the most recent (n = N), we find good scaling collapse of this distance ratio for all n. Experimental techniques that track individual particles, or local groups of particles, such as photo-activation or photobleaching of fluorescently tagged proteins, should be able to observe these single-file effects. However, biological phenomena that depend on local concentration, such as flagellar extension or luminal enzymatic activity, should not exhibit single-file effects.

  18. Roll levelling semi-analytical model for process optimization

    NASA Astrophysics Data System (ADS)

    Silvestre, E.; Garcia, D.; Galdos, L.; Saenz de Argandoña, E.; Mendiguren, J.

    2016-08-01

    Roll levelling is a primary manufacturing process used to remove residual stresses and imperfections of metal strips in order to make them suitable for subsequent forming operations. In the last years the importance of this process has been evidenced with the apparition of Ultra High Strength Steels with strength > 900 MPa. The optimal setting of the machine as well as a robust machine design has become critical for the correct processing of these materials. Finite Element Method (FEM) analysis is the widely used technique for both aspects. However, in this case, the FEM simulation times are above the admissible ones in both machine development and process optimization. In the present work, a semi-analytical model based on a discrete bending theory is presented. This model is able to calculate the critical levelling parameters i.e. force, plastification rate, residual stresses in a few seconds. First the semi-analytical model is presented. Next, some experimental industrial cases are analyzed by both the semi-analytical model and the conventional FEM model. Finally, results and computation times of both methods are compared.

  19. 21 CFR 888.3100 - Ankle joint metal/composite semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Ankle joint metal/composite semi-constrained... Ankle joint metal/composite semi-constrained cemented prosthesis. (a) Identification. An ankle joint metal/composite semi-constrained cemented prosthesis is a device intended to be implanted to replace...

  20. 21 CFR 888.3100 - Ankle joint metal/composite semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ankle joint metal/composite semi-constrained... Ankle joint metal/composite semi-constrained cemented prosthesis. (a) Identification. An ankle joint metal/composite semi-constrained cemented prosthesis is a device intended to be implanted to replace...

  1. 21 CFR 888.3100 - Ankle joint metal/composite semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Ankle joint metal/composite semi-constrained... Ankle joint metal/composite semi-constrained cemented prosthesis. (a) Identification. An ankle joint metal/composite semi-constrained cemented prosthesis is a device intended to be implanted to replace...

  2. 21 CFR 888.3500 - Knee joint femorotibial metal/composite semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Knee joint femorotibial metal/composite semi... § 888.3500 Knee joint femorotibial metal/composite semi-constrained cemented prosthesis. (a) Identification. A knee joint femorotibial metal/composite semi-constrained cemented prosthesis is a...

  3. 21 CFR 888.3500 - Knee joint femorotibial metal/composite semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Knee joint femorotibial metal/composite semi... § 888.3500 Knee joint femorotibial metal/composite semi-constrained cemented prosthesis. (a) Identification. A knee joint femorotibial metal/composite semi-constrained cemented prosthesis is a...

  4. 21 CFR 888.3100 - Ankle joint metal/composite semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Ankle joint metal/composite semi-constrained... Ankle joint metal/composite semi-constrained cemented prosthesis. (a) Identification. An ankle joint metal/composite semi-constrained cemented prosthesis is a device intended to be implanted to replace...

  5. 21 CFR 888.3500 - Knee joint femorotibial metal/composite semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Knee joint femorotibial metal/composite semi... § 888.3500 Knee joint femorotibial metal/composite semi-constrained cemented prosthesis. (a) Identification. A knee joint femorotibial metal/composite semi-constrained cemented prosthesis is a...

  6. 21 CFR 888.3500 - Knee joint femorotibial metal/composite semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Knee joint femorotibial metal/composite semi... § 888.3500 Knee joint femorotibial metal/composite semi-constrained cemented prosthesis. (a) Identification. A knee joint femorotibial metal/composite semi-constrained cemented prosthesis is a...

  7. 33 CFR 147.841 - Atlantis Semi-Submersible safety zone.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Atlantis Semi-Submersible safety... SECURITY (CONTINUED) OUTER CONTINENTAL SHELF ACTIVITIES SAFETY ZONES § 147.841 Atlantis Semi-Submersible safety zone. (a) Description. Atlantis Semi-Submersible, Green Canyon 787 (GC 787), located at...

  8. 33 CFR 147.841 - Atlantis Semi-Submersible safety zone.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Atlantis Semi-Submersible safety... SECURITY (CONTINUED) OUTER CONTINENTAL SHELF ACTIVITIES SAFETY ZONES § 147.841 Atlantis Semi-Submersible safety zone. (a) Description. Atlantis Semi-Submersible, Green Canyon 787 (GC 787), located at...

  9. 33 CFR 147.841 - Atlantis Semi-Submersible safety zone.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 33 Navigation and Navigable Waters 2 2013-07-01 2013-07-01 false Atlantis Semi-Submersible safety... SECURITY (CONTINUED) OUTER CONTINENTAL SHELF ACTIVITIES SAFETY ZONES § 147.841 Atlantis Semi-Submersible safety zone. (a) Description. Atlantis Semi-Submersible, Green Canyon 787 (GC 787), located at...

  10. 33 CFR 147.841 - Atlantis Semi-Submersible safety zone.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 33 Navigation and Navigable Waters 2 2014-07-01 2014-07-01 false Atlantis Semi-Submersible safety... SECURITY (CONTINUED) OUTER CONTINENTAL SHELF ACTIVITIES SAFETY ZONES § 147.841 Atlantis Semi-Submersible safety zone. (a) Description. Atlantis Semi-Submersible, Green Canyon 787 (GC 787), located at...

  11. 33 CFR 147.841 - Atlantis Semi-Submersible safety zone.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 33 Navigation and Navigable Waters 2 2012-07-01 2012-07-01 false Atlantis Semi-Submersible safety... SECURITY (CONTINUED) OUTER CONTINENTAL SHELF ACTIVITIES SAFETY ZONES § 147.841 Atlantis Semi-Submersible safety zone. (a) Description. Atlantis Semi-Submersible, Green Canyon 787 (GC 787), located at...

  12. 40 CFR 430.60 - Applicability; description of the semi-chemical subcategory.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ...-chemical subcategory. 430.60 Section 430.60 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... CATEGORY Semi-Chemical Subcategory § 430.60 Applicability; description of the semi-chemical subcategory... of pulp and paper at semi-chemical mills....

  13. 78 FR 43918 - Agency Information Collection Activities: Extension of a Currently Approved Collection Semi...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-22

    ... Information Collection Activities: Extension of a Currently Approved Collection Semi-Annual Progress Report... Approved Collection. (2) Title of the Form/Collection: Semi-Annual Progress Report for Grantees from the... progress report. The semi-annual progress report is divided into sections that pertain to the...

  14. 21 CFR 888.3110 - Ankle joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ankle joint metal/polymer semi-constrained... Ankle joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. An ankle joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace an...

  15. 21 CFR 888.3160 - Elbow joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Elbow joint metal/polymer semi-constrained... Elbow joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. An elbow joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace an...

  16. 21 CFR 888.3530 - Knee joint femorotibial metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Knee joint femorotibial metal/polymer semi... § 888.3530 Knee joint femorotibial metal/polymer semi-constrained cemented prosthesis. (a) Identification. A knee joint femorotibial metal/polymer semi-constrained cemented prosthesis is a device...

  17. 21 CFR 888.3530 - Knee joint femorotibial metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Knee joint femorotibial metal/polymer semi... § 888.3530 Knee joint femorotibial metal/polymer semi-constrained cemented prosthesis. (a) Identification. A knee joint femorotibial metal/polymer semi-constrained cemented prosthesis is a device...

  18. 21 CFR 888.3800 - Wrist joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Wrist joint metal/polymer semi-constrained... Wrist joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. A wrist joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace a wrist...

  19. 21 CFR 888.3540 - Knee joint patellofemoral polymer/metal semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Knee joint patellofemoral polymer/metal semi... § 888.3540 Knee joint patellofemoral polymer/metal semi-constrained cemented prosthesis. (a) Identification. A knee joint patellofemoral polymer/metal semi-constrained cemented prosthesis is a...

  20. 21 CFR 888.3530 - Knee joint femorotibial metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Knee joint femorotibial metal/polymer semi... § 888.3530 Knee joint femorotibial metal/polymer semi-constrained cemented prosthesis. (a) Identification. A knee joint femorotibial metal/polymer semi-constrained cemented prosthesis is a device...

  1. 21 CFR 888.3160 - Elbow joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Elbow joint metal/polymer semi-constrained... Elbow joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. An elbow joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace an...

  2. 21 CFR 888.3110 - Ankle joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Ankle joint metal/polymer semi-constrained... Ankle joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. An ankle joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace an...

  3. 21 CFR 888.3110 - Ankle joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Ankle joint metal/polymer semi-constrained... Ankle joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. An ankle joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace an...

  4. 21 CFR 888.3660 - Shoulder joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Shoulder joint metal/polymer semi-constrained... Shoulder joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. A shoulder joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace...

  5. 21 CFR 888.3540 - Knee joint patellofemoral polymer/metal semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Knee joint patellofemoral polymer/metal semi... § 888.3540 Knee joint patellofemoral polymer/metal semi-constrained cemented prosthesis. (a) Identification. A knee joint patellofemoral polymer/metal semi-constrained cemented prosthesis is a...

  6. 21 CFR 888.3800 - Wrist joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Wrist joint metal/polymer semi-constrained... Wrist joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. A wrist joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace a wrist...

  7. 21 CFR 888.3110 - Ankle joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Ankle joint metal/polymer semi-constrained... Ankle joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. An ankle joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace an...

  8. 21 CFR 888.3800 - Wrist joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Wrist joint metal/polymer semi-constrained... Wrist joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. A wrist joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace a wrist...

  9. 21 CFR 888.3540 - Knee joint patellofemoral polymer/metal semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Knee joint patellofemoral polymer/metal semi... § 888.3540 Knee joint patellofemoral polymer/metal semi-constrained cemented prosthesis. (a) Identification. A knee joint patellofemoral polymer/metal semi-constrained cemented prosthesis is a...

  10. 21 CFR 888.3800 - Wrist joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Wrist joint metal/polymer semi-constrained... Wrist joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. A wrist joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace a wrist...

  11. 21 CFR 888.3660 - Shoulder joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Shoulder joint metal/polymer semi-constrained... Shoulder joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. A shoulder joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace...

  12. 21 CFR 888.3530 - Knee joint femorotibial metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Knee joint femorotibial metal/polymer semi... § 888.3530 Knee joint femorotibial metal/polymer semi-constrained cemented prosthesis. (a) Identification. A knee joint femorotibial metal/polymer semi-constrained cemented prosthesis is a device...

  13. 21 CFR 888.3530 - Knee joint femorotibial metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Knee joint femorotibial metal/polymer semi... § 888.3530 Knee joint femorotibial metal/polymer semi-constrained cemented prosthesis. (a) Identification. A knee joint femorotibial metal/polymer semi-constrained cemented prosthesis is a device...

  14. 21 CFR 888.3540 - Knee joint patellofemoral polymer/metal semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Knee joint patellofemoral polymer/metal semi... § 888.3540 Knee joint patellofemoral polymer/metal semi-constrained cemented prosthesis. (a) Identification. A knee joint patellofemoral polymer/metal semi-constrained cemented prosthesis is a...

  15. 21 CFR 888.3660 - Shoulder joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Shoulder joint metal/polymer semi-constrained... Shoulder joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. A shoulder joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace...

  16. 21 CFR 888.3800 - Wrist joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Wrist joint metal/polymer semi-constrained... Wrist joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. A wrist joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace a wrist...

  17. 21 CFR 888.3160 - Elbow joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Elbow joint metal/polymer semi-constrained... Elbow joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. An elbow joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace an...

  18. 21 CFR 888.3110 - Ankle joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Ankle joint metal/polymer semi-constrained... Ankle joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. An ankle joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace an...

  19. 21 CFR 888.3160 - Elbow joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Elbow joint metal/polymer semi-constrained... Elbow joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. An elbow joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace an...

  20. 21 CFR 888.3160 - Elbow joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Elbow joint metal/polymer semi-constrained... Elbow joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. An elbow joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace an...

  1. 21 CFR 888.3540 - Knee joint patellofemoral polymer/metal semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Knee joint patellofemoral polymer/metal semi... § 888.3540 Knee joint patellofemoral polymer/metal semi-constrained cemented prosthesis. (a) Identification. A knee joint patellofemoral polymer/metal semi-constrained cemented prosthesis is a...

  2. 21 CFR 888.3660 - Shoulder joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Shoulder joint metal/polymer semi-constrained... Shoulder joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. A shoulder joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace...

  3. 21 CFR 888.3660 - Shoulder joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Shoulder joint metal/polymer semi-constrained... Shoulder joint metal/polymer semi-constrained cemented prosthesis. (a) Identification. A shoulder joint metal/polymer semi-constrained cemented prosthesis is a device intended to be implanted to replace...

  4. 21 CFR 888.3100 - Ankle joint metal/composite semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Ankle joint metal/composite semi-constrained... Ankle joint metal/composite semi-constrained cemented prosthesis. (a) Identification. An ankle joint metal/composite semi-constrained cemented prosthesis is a device intended to be implanted to replace...

  5. 21 CFR 888.3500 - Knee joint femorotibial metal/composite semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Knee joint femorotibial metal/composite semi... § 888.3500 Knee joint femorotibial metal/composite semi-constrained cemented prosthesis. (a) Identification. A knee joint femorotibial metal/composite semi-constrained cemented prosthesis is a...

  6. Semi-Solid Flowable Battery Electrodes: Semi-Solid Flow Cells for Automotive and Grid-Level Energy Storage

    SciTech Connect

    2010-09-01

    BEEST Project: Scientists at 24M are crossing a Li-Ion battery with a fuel cell to develop a semi-solid flow battery. This system relies on some of the same basic chemistry as a standard Li-Ion battery, but in a flow battery the energy storage material is held in external tanks, so storage capacity is not limited by the size of the battery itself. The design makes it easier to add storage capacity by simply increasing the size of the tanks and adding more paste. In addition, 24M's design also is able to extract more energy from the semi-solid paste than conventional Li-Ion batteries. This creates a cost-effective, energy-dense battery that can improve the driving range of EVs or be used to store energy on the electric grid.

  7. Last interglacial semi-desert expansions in southern Africa

    NASA Astrophysics Data System (ADS)

    Urrego, D. H.; Sanchez Goni, M.; Lechevrel, S.; Daniau, A.

    2013-05-01

    While our understanding of the effects of orbital-scale variability on the vegetation has grown during the past decades, empirical data from some climatically important periods and regions are still lacking. Scarce data exist for instance for deep-time glacial-interglacial cycles that could provide suitable analogs for current climate change. Recent global-scale syntheses of vegetation responses to rapid events during the last glacial have been useful, however, these global compilations clearly show that some regions, namely the southern tropics and subtropics, remain understudied. We use pollen analysis of marine sediments from core MD96-2098 to produce a paleoenvironmental record from southern Africa spanning MIS 6 to 3. Our interpretations are supported by an analysis of present-day pollen-vegetation-climate relationships for the region. We applied canonical correspondence analysis (CCA) and detrended correspondence analysis (DCA) on pollen spectra from terrestrial surface samples to investigate these relationships and to identify pollen taxa that are suitable bioclimatic indicators for the different South African biomes. Semi-desert vegetation dominated southern Africa during the MIS 5 interglacial. Expansion of the semi-desert biome into the Namib desert likely resulted from the reduction of the Benguela upwelling and a relative decrease in aridity. In its eastern boundary, the semi-desert likely expanded at the expense of grasslands as a result of increased subtropical high pressure and reduced summer precipitation. Semi-desert expansion in its southern boundary probably resulted from reduced influence of the southern westerlies and decreased winter precipitation. This atmospheric configuration was probably exacerbated during the three warm substages of MIS 5. During glacial isotopic stages MIS 6, 4 and 3 grasslands gained area over the semi-desert as summer precipitation increased. The area occupied by Fynbos vegetation was particularly large at the

  8. Semi Active Control of Civil Structures, Analytical and Numerical Studies

    NASA Astrophysics Data System (ADS)

    Kerboua, M.; Benguediab, M.; Megnounif, A.; Benrahou, K. H.; Kaoulala, F.

    Structural control for civil structures was born out of a need to provide safer and more efficient designs with the reality of limited resources. The purpose of structural control is to absorb and to reflect the energy introduced by dynamic loads such as winds, waves, earthquakes, and traffic. Today, the protection of civil structures from severe dynamic loading is typically achieved by allowing the structures to be damaged. Semi-active control devices, also called "smart" control devices, assume the positive aspects of both the passive and active control devices. A semi-active control strategy is similar to the active control strategy. Only here, the control actuator does not directly apply force to the structure, but instead it is used to control the properties of a passive energy device, a controllable passive damper. Semi-active control strategies can be used in many of the same civil applications as passive and active control. One method of operating smart cable dampers is in a purely passive capacity, supplying the dampers with constant optimal voltage. The advantages to this strategy are the relative simplicity of implementing the control strategy as compared to a smart or active control strategy and that the dampers are more easily optimally tuned in- place, eliminating the need to have passive dampers with unique optimal damping coefficients. This research investigated semi-active control of civil structures for natural hazard mitigation. The research has two components, the seismic protection of buildings and the mitigation of wind-induced vibration in structures. An ideal semi-active motion equation of a composite beam that consists of a cantilever beam bonded with a PZT patch using Hamilton's principle and Galerkin's method was treated. A series R-L and a parallel R-L shunt circuits are coupled into the motion equation respectively by means of the constitutive relation of piezoelectric material and Kirchhoff's law to control the beam vibration. A

  9. Development and Application of Grid-GA Model in a Semi-Humid and Semi-Arid Basin

    NASA Astrophysics Data System (ADS)

    Wang, L.; Li, Z.; Bao, H.; Yu, Z.

    2009-12-01

    Modeling the hydrologic processes in semi-arid and semi-humid basins is specially challenging due to the specific characteristics of these basins. In this paper, combining with GIS technology and DEM, the Grid- and Green-Ampt infiltration approach-based distributed hydrologic model of the runoff-production in excess infiltration is developed (Grid-GA model). In Grid-GA model, the Green-Ampt infiltration approach has improved in three parts: (1) the effective hydraulic conductivity of the wetting front at saturation, is power function decaying with the depth of the wetting front; (2) F, the cumulative infiltration, is modified at the end of every time step; (3) the moisture content rate of the soil, is redistribution during the infiltration process. In flow concentration formation, there are kinematic wave approach for un-channel grid and Muskingum approach for channel grid. The model described that includes vegetation and root interception, evapotranspiration, and runoff generation via the excess infiltration mechanism, as well as subsurface via the Darcian approach used by TOPMODEL, runoff concentration, and flow routing. The water exchange among grids within the watershed and the runoff routing along the river drainage networks are taken into consideration in the model. The Grid-GA model is applied to Gaoli basin in Yi River, a tributary of the Yishusi Watershed, with an area of 552 km2 for flood simulation. The results show that the model performs well in the simulation and can be used for flood forecasting in the semi-humid and semi-arid region.

  10. Groundwater dependent ecohydrology in a semi-arid oak savanna (Invited)

    NASA Astrophysics Data System (ADS)

    Miller, G. R.; Rubin, Y.; Baldocchi, D. D.; Chen, X.; Ma, S.

    2010-12-01

    Groundwater can serve as an important resource for woody vegetation in semi-arid landscapes, particularly when soil water is functionally depleted and unavailable to plants. This study examines the uptake of groundwater by deciduous blue oak trees (Quercus douglasii) in a California oak savanna. Here, we present a suite of direct and indirect measurement techniques, combined with modeling, that demonstrate its occurrence and quantify its rates. The study site is similar to others with shallow-soil ecohydrology: it is underlain by a thin, rocky soil layer followed fractured metavolcanic bedrock. Typical depth to groundwater is approximately 8 m and varies from 7- 10 m, both spatially and temporally. A variety of water storage and flux measurements were collected from 2005 to 2008, including groundwater levels, soil moisture contents, sap flows, and latent heat fluxes. During the dry season, groundwater uptake rates ranged from 4 to 25 mm per month, and approximately 80% of total ET during June, July, and August came from groundwater. Leaf and soil water potentials supported these results, indicating that groundwater uptake was thermodynamically favorable over soil water uptake for key portions of the growing season. Sap flow rates suggest differential access to groundwater by trees of varying size classes. Dynamic groundwater-soil-plant-atmosphere modeling has shown that in order to achieve these uptake rates, approximately 20% of roots must be exposed to groundwater. Modeled evapotranspiration rates drop dramatically during the late summer when this connection is severed (Figure 1). These findings strongly suggest that blue oaks should be considered obligate phreatophytes, and that groundwater reserves provide a buffer to rapid changes in their hydro-climate, if these assets are not otherwise depleted by prolonged drought or human consumption. While groundwater uptake may provide for short-term protection, it should be viewed not as a mechanism for continued plant

  11. Where Does the River Run? Lessons from a Semi-Arid River

    NASA Astrophysics Data System (ADS)

    Meixner, T.; Soto, C. D.; Richter, H.; Uhlman, K.

    2009-12-01

    Spatial data sets to assess the nature of stream groundwater interactions and the resulting power law/fractal structure of travel time distributions are rare. Spatial data sets can be collected using high technology or by use of a large number of field assistants. The labor intensive way is expensive unless the public can be enlisted as citizen scientists to gather large, robust, spatial data sets robustly and cheaply. Such an effort requires public interest and the ability of a few to organize such an effort at a basin if not regional scale. The San Pedro basin offers such an opportunity for citizen science due to the water resource restrictions of the basins semi-arid climate. Since 1999 The Nature Conservancy, in cooperation with the Upper San Pedro Partnership, the public at large and various university and federal science agency participants, has been mapping where the San Pedro River has water present versus where it is dry. This mapping has used an army of volunteers armed with GPS units, clipboards and their eyes to make the determination if a given 10m reach of the river is wet or dry. These wet/dry mapping data now exist for 11 different annual surveys. These data are unique and enable an investigation of the hydrologic connectedness of flowing waters within this system. Analysis of these data reveals several important findings. The total river area that is wet is strongly correlated with stream flow as observed at three USGS gauges. The correlation is strongest however for 90 day and 1 year average flows rather than more local in time observations such as the daily, 7 day or monthly mean flow at the gauges. This result indicates that where the river is flowing depends on long term hydrologic conditions. The length of river reach that is mapped as wet or dry is indicative of the travel distance and thus time that water travels in the surface (wet) and subsurface (dry) of the river system. The reach length that is mapped as wet follows a power law function

  12. Field assessment of semi-aerobic condition and the methane correction factor for the semi-aerobic landfills provided by IPCC guidelines.

    PubMed

    Jeong, Sangjae; Nam, Anwoo; Yi, Seung-Muk; Kim, Jae Young

    2015-02-01

    According to IPCC guidelines, a semi-aerobic landfill site produces one-half of the amount of CH4 produced by an equally-sized anaerobic landfill site. Therefore categorizing the landfill type is important on greenhouse gas inventories. In order to assess semi-aerobic condition in the sites and the MCF value for semi-aerobic landfill, landfill gas has been measured from vent pipes in five semi-aerobically designed landfills in South Korea. All of the five sites satisfied requirements of semi-aerobic landfills in 2006 IPCC guidelines. However, the ends of leachate collection pipes which are main entrance of air in the semi-aerobic landfill were closed in all five sites. The CH4/CO2 ratio in landfill gas, indicator of aerobic and anaerobic decomposition, ranged from 1.08 to 1.46 which is higher than the values (0.3-1.0) reported for semi-aerobic landfill sites and is rather close to those (1.0-2.0) for anaerobic landfill sites. The low CH4+CO2% in landfill gas implied air intrusion into the landfill. However, there was no evidence that air intrusion has caused by semi-aerobic design and operation. Therefore, the landfills investigated in this study are difficult to be classified as semi-aerobic landfills. Also MCF of 0.5 may significantly underestimate methane emissions compared to other researches. According to the carbon mass balance analyses, the higher MCF needs to be proposed for semi-aerobic landfills. Consequently, methane emission estimate should be based on field evaluation for the semi-aerobically designed landfills.

  13. Semi-automated Image Processing for Preclinical Bioluminescent Imaging

    PubMed Central

    Slavine, Nikolai V; McColl, Roderick W

    2015-01-01

    Objective Bioluminescent imaging is a valuable noninvasive technique for investigating tumor dynamics and specific biological molecular events in living animals to better understand the effects of human disease in animal models. The purpose of this study was to develop and test a strategy behind automated methods for bioluminescence image processing from the data acquisition to obtaining 3D images. Methods In order to optimize this procedure a semi-automated image processing approach with multi-modality image handling environment was developed. To identify a bioluminescent source location and strength we used the light flux detected on the surface of the imaged object by CCD cameras. For phantom calibration tests and object surface reconstruction we used MLEM algorithm. For internal bioluminescent sources we used the diffusion approximation with balancing the internal and external intensities on the boundary of the media and then determined an initial order approximation for the photon fluence we subsequently applied a novel iterative deconvolution method to obtain the final reconstruction result. Results We find that the reconstruction techniques successfully used the depth-dependent light transport approach and semi-automated image processing to provide a realistic 3D model of the lung tumor. Our image processing software can optimize and decrease the time of the volumetric imaging and quantitative assessment. Conclusion The data obtained from light phantom and lung mouse tumor images demonstrate the utility of the image reconstruction algorithms and semi-automated approach for bioluminescent image processing procedure. We suggest that the developed image processing approach can be applied to preclinical imaging studies: characteristics of tumor growth, identify metastases, and potentially determine the effectiveness of cancer treatment. PMID:26618187

  14. Fish Predation by Semi-Aquatic Spiders: A Global Pattern

    PubMed Central

    Nyffeler, Martin; Pusey, Bradley J.

    2014-01-01

    More than 80 incidences of fish predation by semi-aquatic spiders – observed at the fringes of shallow freshwater streams, rivers, lakes, ponds, swamps, and fens – are reviewed. We provide evidence that fish predation by semi-aquatic spiders is geographically widespread, occurring on all continents except Antarctica. Fish predation by spiders appears to be more common in warmer areas between 40° S and 40° N. The fish captured by spiders, usually ranging from 2–6 cm in length, are among the most common fish taxa occurring in their respective geographic area (e.g., mosquitofish [Gambusia spp.] in the southeastern USA, fish of the order Characiformes in the Neotropics, killifish [Aphyosemion spp.] in Central and West Africa, as well as Australian native fish of the genera Galaxias, Melanotaenia, and Pseudomugil). Naturally occurring fish predation has been witnessed in more than a dozen spider species from the superfamily Lycosoidea (families Pisauridae, Trechaleidae, and Lycosidae), in two species of the superfamily Ctenoidea (family Ctenidae), and in one species of the superfamily Corinnoidea (family Liocranidae). The majority of reports on fish predation by spiders referred to pisaurid spiders of the genera Dolomedes and Nilus (>75% of observed incidences). There is laboratory evidence that spiders from several more families (e.g., the water spider Argyroneta aquatica [Cybaeidae], the intertidal spider Desis marina [Desidae], and the ‘swimming’ huntsman spider Heteropoda natans [Sparassidae]) predate fish as well. Our finding of such a large diversity of spider families being engaged in fish predation is novel. Semi-aquatic spiders captured fish whose body length exceeded the spiders’ body length (the captured fish being, on average, 2.2 times as long as the spiders). Evidence suggests that fish prey might be an occasional prey item of substantial nutritional importance. PMID:24940885

  15. Fish predation by semi-aquatic spiders: a global pattern.

    PubMed

    Nyffeler, Martin; Pusey, Bradley J

    2014-01-01

    More than 80 incidences of fish predation by semi-aquatic spiders--observed at the fringes of shallow freshwater streams, rivers, lakes, ponds, swamps, and fens--are reviewed. We provide evidence that fish predation by semi-aquatic spiders is geographically widespread, occurring on all continents except Antarctica. Fish predation by spiders appears to be more common in warmer areas between 40° S and 40° N. The fish captured by spiders, usually ranging from 2-6 cm in length, are among the most common fish taxa occurring in their respective geographic area (e.g., mosquitofish [Gambusia spp.] in the southeastern USA, fish of the order Characiformes in the Neotropics, killifish [Aphyosemion spp.] in Central and West Africa, as well as Australian native fish of the genera Galaxias, Melanotaenia, and Pseudomugil). Naturally occurring fish predation has been witnessed in more than a dozen spider species from the superfamily Lycosoidea (families Pisauridae, Trechaleidae, and Lycosidae), in two species of the superfamily Ctenoidea (family Ctenidae), and in one species of the superfamily Corinnoidea (family Liocranidae). The majority of reports on fish predation by spiders referred to pisaurid spiders of the genera Dolomedes and Nilus (>75% of observed incidences). There is laboratory evidence that spiders from several more families (e.g., the water spider Argyroneta aquatica [Cybaeidae], the intertidal spider Desis marina [Desidae], and the 'swimming' huntsman spider Heteropoda natans [Sparassidae]) predate fish as well. Our finding of such a large diversity of spider families being engaged in fish predation is novel. Semi-aquatic spiders captured fish whose body length exceeded the spiders' body length (the captured fish being, on average, 2.2 times as long as the spiders). Evidence suggests that fish prey might be an occasional prey item of substantial nutritional importance.

  16. Semi-Analytic Reconstruction of Flux in Finite Volume Formulations

    NASA Technical Reports Server (NTRS)

    Gnoffo, Peter A.

    2006-01-01

    Semi-analytic reconstruction uses the analytic solution to a second-order, steady, ordinary differential equation (ODE) to simultaneously evaluate the convective and diffusive flux at all interfaces of a finite volume formulation. The second-order ODE is itself a linearized approximation to the governing first- and second- order partial differential equation conservation laws. Thus, semi-analytic reconstruction defines a family of formulations for finite volume interface fluxes using analytic solutions to approximating equations. Limiters are not applied in a conventional sense; rather, diffusivity is adjusted in the vicinity of changes in sign of eigenvalues in order to achieve a sufficiently small cell Reynolds number in the analytic formulation across critical points. Several approaches for application of semi-analytic reconstruction for the solution of one-dimensional scalar equations are introduced. Results are compared with exact analytic solutions to Burger s Equation as well as a conventional, upwind discretization using Roe s method. One approach, the end-point wave speed (EPWS) approximation, is further developed for more complex applications. One-dimensional vector equations are tested on a quasi one-dimensional nozzle application. The EPWS algorithm has a more compact difference stencil than Roe s algorithm but reconstruction time is approximately a factor of four larger than for Roe. Though both are second-order accurate schemes, Roe s method approaches a grid converged solution with fewer grid points. Reconstruction of flux in the context of multi-dimensional, vector conservation laws including effects of thermochemical nonequilibrium in the Navier-Stokes equations is developed.

  17. A dorsolateral prefrontal cortex semi-automatic segmenter

    NASA Astrophysics Data System (ADS)

    Al-Hakim, Ramsey; Fallon, James; Nain, Delphine; Melonakos, John; Tannenbaum, Allen

    2006-03-01

    Structural, functional, and clinical studies in schizophrenia have, for several decades, consistently implicated dysfunction of the prefrontal cortex in the etiology of the disease. Functional and structural imaging studies, combined with clinical, psychometric, and genetic analyses in schizophrenia have confirmed the key roles played by the prefrontal cortex and closely linked "prefrontal system" structures such as the striatum, amygdala, mediodorsal thalamus, substantia nigra-ventral tegmental area, and anterior cingulate cortices. The nodal structure of the prefrontal system circuit is the dorsal lateral prefrontal cortex (DLPFC), or Brodmann area 46, which also appears to be the most commonly studied and cited brain area with respect to schizophrenia. 1, 2, 3, 4 In 1986, Weinberger et. al. tied cerebral blood flow in the DLPFC to schizophrenia.1 In 2001, Perlstein et. al. demonstrated that DLPFC activation is essential for working memory tasks commonly deficient in schizophrenia. 2 More recently, groups have linked morphological changes due to gene deletion and increased DLPFC glutamate concentration to schizophrenia. 3, 4 Despite the experimental and clinical focus on the DLPFC in structural and functional imaging, the variability of the location of this area, differences in opinion on exactly what constitutes DLPFC, and inherent difficulties in segmenting this highly convoluted cortical region have contributed to a lack of widely used standards for manual or semi-automated segmentation programs. Given these implications, we developed a semi-automatic tool to segment the DLPFC from brain MRI scans in a reproducible way to conduct further morphological and statistical studies. The segmenter is based on expert neuroanatomist rules (Fallon-Kindermann rules), inspired by cytoarchitectonic data and reconstructions presented by Rajkowska and Goldman-Rakic. 5 It is semi-automated to provide essential user interactivity. We present our results and provide details on

  18. Semi-regular biorthogonal pairs and generalized Riesz bases

    NASA Astrophysics Data System (ADS)

    Inoue, H.

    2016-11-01

    In this paper we introduce general theories of semi-regular biorthogonal pairs, generalized Riesz bases and its physical applications. Here we deal with biorthogonal sequences {ϕn} and {ψn} in a Hilbert space H , with domains D ( ϕ ) = { x ∈ H ; ∑ k = 0 ∞ |" separators=" ( x | ϕ k ) | 2 < ∞ } and D ( ψ ) = { x ∈ H ; ∑ k = 0 ∞ |" separators=" ( x | ψ k ) | 2 < ∞ } and linear spans Dϕ ≡ Span{ϕn} and Dψ ≡ Span{ψn}. A biorthogonal pair ({ϕn}, {ψn}) is called regular if both Dϕ and Dψ are dense in H , and it is called semi-regular if either Dϕ and D(ϕ) or Dψ and D(ψ) are dense in H . In a previous paper [H. Inoue, J. Math. Phys. 57, 083511 (2016)], we have shown that if ({ϕn}, {ψn}) is a regular biorthogonal pair then both {ϕn} and {ψn} are generalized Riesz bases defined in the work of Inoue and Takakura [J. Math. Phys. 57, 083505 (2016)]. Here we shall show that the same result holds true if the pair is only semi-regular by using operators Tϕ,e, Te,ϕ, Tψ,e, and Te,ψ defined by an orthonormal basis e in H and a biorthogonal pair ({ϕn}, {ψn}). Furthermore, we shall apply this result to pseudo-bosons in the sense of the papers of Bagarello [J. Math. Phys. 51, 023531 (2010); J. Phys. A 44, 015205 (2011); Phys. Rev. A 88, 032120 (2013); and J. Math. Phys. 54, 063512 (2013)].

  19. Towards semi-automated non-destructive evaluation

    NASA Astrophysics Data System (ADS)

    Fradkin, L.; Zernov, V.; Elston, G.; Taneja, R.; Bell, I.; Lines, D.; Wharrie, J.; Fitzgerald, P.

    2013-08-01

    A demonstrator has been developed showing feasibility of semi-automatic characterisation of large planar flaws in steel using ultrasonic transducer arrays. The unit is based on a real-time ultrasonic imager deploying National Instruments hardware and software, is connected to an IMASONIC linear phased array containing 128 elements and incorporates a novel flaw characterisation algorithm, which is a model-based variant of Total Focusing Method, taking into account undulations in inspection surface. It has been shown to process RF data collected in immersion reasonably fast and be capable of detecting and characterising with reasonable accuracy large planar defects.

  20. Semi-Huber potential function for image segmentation.

    PubMed

    Gutiérrez, Osvaldo; de la Rosa, Ismael; Villa, Jesús; González, Efrén; Escalante, Nivia

    2012-03-12

    In this work, a novel model of Markov Random Field (MRF) is introduced. Such a model is based on a proposed Semi-Huber potential function and it is applied successfully to image segmentation in presence of noise. The main difference with respect to other half-quadratic models that have been taken as a reference is, that the number of parameters to be tuned in the proposed model is smaller and simpler. The idea is then, to choose adequate parameter values heuristically for a good segmentation of the image. In that sense, some experimental results show that the proposed model allows an easier parameter adjustment with reasonable computation times.

  1. Two-Photon Exchange in (Semi-)Inclusive DIS

    SciTech Connect

    Schlegel, M.; Metz, A.

    2009-08-04

    In this note we consider effects of a Two-Photon Exchange (TPE) in inclusive DIS and semi-inclusive DIS (SIDIS). In particular, transverse single spin asymmetries are generated in inclusive DIS if more than one photon is exchanged between the lepton and the hadron. We briefly summarize the TPE in DIS in the parton model and extend our approach to SIDIS, where a new leading twist sin(2{phi}) contribution to the longitudinal beam spin asymmetry shows up. Possible TPE effects for the Sivers and the Collins asymmetries in SIDIS are power-suppressed.

  2. Two-Photon Exchange in (Semi-)Inclusive DIS

    SciTech Connect

    Schlegel, Marc; Metz, Andreas

    2009-01-01

    In this note we consider effects of a Two-Photon Exchange (TPE) in inclusive DIS and semi-inclusive DIS (SIDIS). In particular, transverse single spin asymmetries are generated in inclusive DIS if more than one photon is exchanged between the lepton and the hadron. We briefly summarize the TPE in DIS in the parton model and extend our approach to SIDIS, where a new leading twist $\\sin(2\\phi)$ contribution to the longitudinal beam spin asymmetry shows up. Possible TPE effects for the Sivers and the Collins asymmetries in SIDIS are power-suppressed.

  3. Semi-automatic pusher machine leveler bar control and method

    SciTech Connect

    Berenato, J.W. III; Raivel, E.L. Jr.; Strepelis, J.J.

    1985-11-26

    A leveler bar for a coke oven is controlled in its travel toward and away from the coke side of the oven by semi-automatic means to move the leveler bar during a ''cycle'' mode through half strokes and during the ''finish'' mode it performs four ''full'' strokes of which a full stroke can mean a 3/4 distance of full travel across the oven. Electrical circuitry which modifies or adds to prior art circuitry to accomplish this leveler bar movement is included herein.

  4. Positive spaces, generalized semi-densities, and quantum interactions

    NASA Astrophysics Data System (ADS)

    Canarutto, Daniel

    2012-03-01

    The basics of quantum particle physics on a curved Lorentzian background are expressed in a formulation which has original aspects and exploits some non-standard mathematical notions. In particular, positive spaces and generalized semi-densities (in a distributional sense) are shown to link, in a natural way, discrete multi-particle spaces to distributional bundles of quantum states. The treatment of spinor and boson fields is partly original also from an algebraic point of view and suggests a non-standard approach to quantum interactions. The case of electroweak interactions provides examples.

  5. Semi-Formal Description of KVM/370 Trusted Processes

    DTIC Science & Technology

    1977-12-09

    rmnNT A~ /( -Ap.rove.d foT public zlaw 12 22 L v0 Distri ~ubution unlimited / MI 3 December 1377 System Development Corporation Contract MDA903-76-C...Dist Special 11 3+ 9 December 1577 System Development Corporation Operator ProcessTI-9/1/9 Operator Process Semi-Formal Description This section...llapUser Id) Answer: recordJ HMIS: string Text: string emd 2 9 Decemberr 1977 System Development Corporation Operator Process TM-68G2/111/08

  6. Mixed conduction in semi-insulating gallium arsenide

    NASA Astrophysics Data System (ADS)

    Winter, J. J.; Leupold, H. A.; Ross, R. L.; Ballato, A.

    1982-12-01

    Hall effect and conductivity measurements made on semi-insulating bulk GaAs are examined by a new approach to mixed conduction analysis. Based on Fermi level and electron mobility analyses of conductivity and Hall coefficient, it uses revised values of effective densities of states at the band edges, and electron/hole mobility ratios recently adopted by other workers. The treatment provides a visual analysis of the system in terms of the electrical parameters and impurity densities, and establishes criteria for the onset of mixed conduction.

  7. Toughening of PMR composites by semi-interpenetrating networks

    NASA Technical Reports Server (NTRS)

    Tiwari, S. N.; Srinivansan, K.

    1991-01-01

    Polymerization of monomer reactants (PMR-15) type polyimide and RP46 prepregs were drum wound using IM-7 fibers. Prepregging and processing conditions were optimized to yield good quality laminates with fiber volume fractions of 60 percent (+/- 2 percent). Samples were fabricated and tested to determine comprehensive engineering properties of both systems. These included 0 deg flexure, short beam shear, transverse flexure and tension, 0 deg tension and compression, intralaminar shear, short block compression, mode 1 and 2 fracture toughness, and compression after impact properties. Semi-2-IPN (interpenetrating polymer networks) toughened PMR-15 and RP46 laminates were also fabricated and tested for the same properties.

  8. Ball Semi-Rigid Advanced Mirror System Demonstrator (AMSD)

    NASA Technical Reports Server (NTRS)

    Kendrick, Stephen; Russell, Kevin (Technical Monitor)

    2001-01-01

    The AMSD Program is to design, fabricate, and test a 1.4-m point-to-point hexagon mirror system. The Ball semi-rigid approach will be described and its current status presented, The mirror system includes a lightweighted beryllium mirror that is attached through flexures and actuators to a composite reaction structure enabling optical performance at ambient and cryogenic temperatures and allowing changes of curvature to be imposed via actuation. This program is administered through NASA MSFC and is jointly funded by NASA, the USAF, and the NRO.

  9. Tele-assistance for semi-autonomous robots

    NASA Technical Reports Server (NTRS)

    Rogers, Erika; Murphy, Robin R.

    1994-01-01

    This paper describes a new approach in semi-autonomous mobile robots. In this approach the robot has sufficient computerized intelligence to function autonomously under a certain set of conditions, while the local system is a cooperative decision making unit that combines human and machine intelligence. Communication is then allowed to take place in a common mode and in a common language. A number of exception-handling scenarios that were constructed as a result of experiments with actual sensor data collected from two mobile robots were presented.

  10. Charge transfer to a semi-esterified bifunctional phenol

    NASA Astrophysics Data System (ADS)

    Brede, O.; Hermann, R.; Orthner, H.

    1996-03-01

    The charge transfer from solvent radical cations of n-butyl chloride and cyclohexane to 2-butyl-6(3'-t-butyl-2'-hydroxy-5'-methylbenzyl)-4-methyl-phenylacrylate (GM) yields in the first step phenoxyl radicals as well as acrylate radical cations of this semi-acrylated bifunctional phenol. Subsequently an intramolecular charge transfer from the acrylate radical cation to the phenol group takes place. Because of the instability of phenol radical cations, under our experimental conditions (nanosecond pulse radiolysis, non-polar solvents, room temperature) phenoxyl radicals are the only observable products of phenol ionization.

  11. A Generic Result in Linear Semi-Infinite Optimization

    SciTech Connect

    Goberna, Miguel A. Lopez, Marco A. Todorov, Maxim I.

    2003-10-15

    In this paper we consider the space of all the linear semi-infinite programming problems with the same index set, endowed with a suitable topology. We provide a constructive proof of the following generic result:if we confine ourselves to the class of problems having a bounded set of coefficient vectors (those vectors appearing in the left-hand side of the constraints), the set of those problems which have a strongly unique optimal solution contains an open and dense subset of the set of solvable problems in the same class.

  12. Markov and semi-Markov processes as a failure rate

    NASA Astrophysics Data System (ADS)

    Grabski, Franciszek

    2016-06-01

    In this paper the reliability function is defined by the stochastic failure rate process with a non negative and right continuous trajectories. Equations for the conditional reliability functions of an object, under assumption that the failure rate is a semi-Markov process with an at most countable state space are derived. A proper theorem is presented. The linear systems of equations for the appropriate Laplace transforms allow to find the reliability functions for the alternating, the Poisson and the Furry-Yule failure rate processes.

  13. Stereocontrolled semi-syntheses of deguelin and tephrosin.

    PubMed

    Russell, David A; Freudenreich, Julien J; Ciardiello, Joe J; Sore, Hannah F; Spring, David R

    2017-02-21

    We describe stereocontrolled semi-syntheses of deguelin and tephrosin, anti-cancer rotenoids isolated from Tephrosia vogelii. Firstly, we present a new two-step transformation of rotenone into rot-2'-enonic acid via a zinc-mediated ring opening of rotenone hydrobromide. Secondly, following conversion of rot-2'-enonic acid into deguelin, a chromium-mediated hydroxylation provides tephrosin as a single diastereoisomer. An Étard-like reaction mechanism is proposed to account for the stereochemical outcome. Our syntheses of deguelin and tephrosin are operationally simple, scalable and high yielding, offering considerable advantages over previous methods.

  14. A Semi-Classical Model to Study Nuclear Fragmentation

    NASA Astrophysics Data System (ADS)

    Navarro, Martha; Chernomoretz, Ariel; Dorso, Claudio; Lopez, Jorge

    1999-10-01

    A semi-classical model based on the use of molecular dynamics has been developed for the study of heavy-ion reactions at intermediate energies. The model reproduces nucleon-nucleon cross sections through the use of a two-body potential. The study covers several characteristics of heavy-ion collisions, such as formation of necks, and formation of intermediate residue. Preliminary results on the use of the model to study the caloric curve of nuclear matter and the temperature evolution of the system are also discussed.

  15. Semi-empirical determination of radiative parameters for atomic nickel

    NASA Astrophysics Data System (ADS)

    Ruczkowski, J.; Elantkowska, M.; Dembczyński, J.

    2017-01-01

    The aim of this article is to determine the values of the radiative parameters for atomic nickel by means of a semi-empirical method. The calculated values of oscillator strengths and lifetimes are, in the majority of cases, in good agreement with experimental data. Our calculation procedures allowed us to obtain the values of transition integrals and predict the values of oscillator strengths for transitions over a wide spectral range and radiative lifetimes for excited levels. Furthermore, the predicted values will be useful when the experimental values are not known.

  16. Semi-actuator disk theory for compressor choke flutter

    NASA Technical Reports Server (NTRS)

    Micklow, J.; Jeffers, J.

    1981-01-01

    A mathematical anaysis predict the unsteady aerodynamic utilizing semi actuator theory environment for a cascade of airfoils harmonically oscillating in choked flow was developed. A normal shock is located in the blade passage, its position depending on the time dependent geometry, and pressure perturbations of the system. In addition to shock dynamics, the model includes the effect of compressibility, interblade phase lag, and an unsteady flow field upstream and downstream of the cascade. Calculated unsteady aerodynamics were compared with isolated airfoil wind tunnel data, and choke flutter onset boundaries were compared with data from testing of an F100 high pressure compressor stage.

  17. Semi device independence of the BB84 protocol

    NASA Astrophysics Data System (ADS)

    Woodhead, Erik

    2016-05-01

    The BB84 quantum key distribution protocol is semi device independent in the sense that it can be shown to be secure if just one of the users’ devices is restricted to a qubit Hilbert space. Here, we derive an analytic lower bound on the asymptotic secret key rate for the entanglement-based version of BB84 assuming only that one of the users performs unknown qubit POVMs. The result holds against the class of collective attacks and reduces to the well known Shor-Preskill key rate for correlations corresponding to the ideal BB84 correlations mixed with any amount of random noise.

  18. Performability analysis using semi-Markov reward processes

    NASA Technical Reports Server (NTRS)

    Ciardo, Gianfranco; Marie, Raymond A.; Sericola, Bruno; Trivedi, Kishor S.

    1990-01-01

    Beaudry (1978) proposed a simple method of computing the distribution of performability in a Markov reward process. Two extensions of Beaudry's approach are presented. The method is generalized to a semi-Markov reward process by removing the restriction requiring the association of zero reward to absorbing states only. The algorithm proceeds by replacing zero-reward nonabsorbing states by a probabilistic switch; it is therefore related to the elimination of vanishing states from the reachability graph of a generalized stochastic Petri net and to the elimination of fast transient states in a decomposition approach to stiff Markov chains. The use of the approach is illustrated with three applications.

  19. User's manual for semi-circular compact range reflector code

    NASA Technical Reports Server (NTRS)

    Gupta, Inder J.; Burnside, Walter D.

    1986-01-01

    A computer code was developed to analyze a semi-circular paraboloidal reflector antenna with a rolled edge at the top and a skirt at the bottom. The code can be used to compute the total near field of the antenna or its individual components at a given distance from the center of the paraboloid. Thus, it is very effective in computing the size of the sweet spot for RCS or antenna measurement. The operation of the code is described. Various input and output statements are explained. Some results obtained using the computer code are presented to illustrate the code's capability as well as being samples of input/output sets.

  20. Transverse momentum dependence of semi-inclusive pion production

    SciTech Connect

    Hamlet Mkrtchyan; Peter Bosted

    2007-09-19

    Cross sections for semi-inclusive electroproduction of charged pions ($\\pi^{\\pm}$) from both proton and deuteron targets were measured for $0.2<0.5$, $2<4$ GeV$^2$, $0.3<1$, and $P_t^2<0.2$ GeV$^2$. We find the azimuthal dependence to be small and consistent with zero, for $P_t<0.1$ GeV. In the context of a simple fit, the initial transverse momenta of $d$ quarks tends to be larger than for $u$ quarks, while the transverse momentum width of the favored fragmentation function is slightly larger than that of the unfavored function.

  1. Implementation of a microcontroller-based semi-automatic coagulator.

    PubMed

    Chan, K; Kirumira, A; Elkateeb, A

    2001-01-01

    The coagulator is an instrument used in hospitals to detect clot formation as a function of time. Generally, these coagulators are very expensive and therefore not affordable by a doctors' office and small clinics. The objective of this project is to design and implement a low cost semi-automatic coagulator (SAC) prototype. The SAC is capable of assaying up to 12 samples and can perform the following tests: prothrombin time (PT), activated partial thromboplastin time (APTT), and PT/APTT combination. The prototype has been tested successfully.

  2. Correlation functions in hard and (semi-)inclusive processes

    SciTech Connect

    Schlegel, Marc; Meissner, Stephan; Metz, Andreas

    2009-01-01

    Possible relations between two a priori different classes of parton distributions, the Generalized Parton Distributions (GPDs) and the Transverse Momentum Dependent parton distributions (TMDs), are discussed in this note. Although these relations were proven to hold exactly only in simple models they imply an appealingly simple and intuitive explanation for single-spin asymmetries in semi-inclusive deep-inelastic scattering. In this context we perform a first classification of common mother functions of GPDs and TMDs, so-called Generalized Transverse Momentum Dependent parton distributions (GTMDs), investigate their GPD- and TMD-limits, and gain new insight into the nature of these relations.

  3. Semi-automatic method for routine evaluation of fibrinolytic components

    PubMed Central

    Collen, D.; Tytgat, G.; Verstraete, M.

    1968-01-01

    A semi-automatic method for the routine evaluation of fibrinolytic activity is described. The principle is based upon graphic recording by a multichannel voltmeter of tension drops over a potentiometer, caused by variations in the influence of light upon a light-dependent resistance, resulting from modifications in the composition of the fibrin fibres by lysis. The method is applied to the assessment of certain fibrinolytic factors with widespread fibrinolytic endpoints, and the results are compared with simultaneously obtained visual data on the plasmin assay, the plasminogen assay, and on the euglobulin clot lysis time. Images PMID:4237924

  4. Field assessment of semi-aerobic condition and the methane correction factor for the semi-aerobic landfills provided by IPCC guidelines

    SciTech Connect

    Jeong, Sangjae; Nam, Anwoo; Yi, Seung-Muk; Kim, Jae Young

    2015-02-15

    Highlights: • CH{sub 4}/CO{sub 2} and CH{sub 4} + CO{sub 2}% are proposed as indices to evaluate semi-aerobic landfills. • A landfill which CH{sub 4}/CO{sub 2} > 1.0 is difficult to be categorized as semi-aerobic landfill. • Field conditions should be carefully investigated to determine landfill types. • The MCF default value for semi-aerobic landfills underestimates the methane emissions. - Abstract: According to IPCC guidelines, a semi-aerobic landfill site produces one-half of the amount of CH{sub 4} produced by an equally-sized anaerobic landfill site. Therefore categorizing the landfill type is important on greenhouse gas inventories. In order to assess semi-aerobic condition in the sites and the MCF value for semi-aerobic landfill, landfill gas has been measured from vent pipes in five semi-aerobically designed landfills in South Korea. All of the five sites satisfied requirements of semi-aerobic landfills in 2006 IPCC guidelines. However, the ends of leachate collection pipes which are main entrance of air in the semi-aerobic landfill were closed in all five sites. The CH{sub 4}/CO{sub 2} ratio in landfill gas, indicator of aerobic and anaerobic decomposition, ranged from 1.08 to 1.46 which is higher than the values (0.3–1.0) reported for semi-aerobic landfill sites and is rather close to those (1.0–2.0) for anaerobic landfill sites. The low CH{sub 4} + CO{sub 2}% in landfill gas implied air intrusion into the landfill. However, there was no evidence that air intrusion has caused by semi-aerobic design and operation. Therefore, the landfills investigated in this study are difficult to be classified as semi-aerobic landfills. Also MCF of 0.5 may significantly underestimate methane emissions compared to other researches. According to the carbon mass balance analyses, the higher MCF needs to be proposed for semi-aerobic landfills. Consequently, methane emission estimate should be based on field evaluation for the semi-aerobically designed landfills.

  5. Monte Carlo Simulation of Markov, Semi-Markov, and Generalized Semi- Markov Processes in Probabilistic Risk Assessment

    NASA Technical Reports Server (NTRS)

    English, Thomas

    2005-01-01

    A standard tool of reliability analysis used at NASA-JSC is the event tree. An event tree is simply a probability tree, with the probabilities determining the next step through the tree specified at each node. The nodal probabilities are determined by a reliability study of the physical system at work for a particular node. The reliability study performed at a node is typically referred to as a fault tree analysis, with the potential of a fault tree existing.for each node on the event tree. When examining an event tree it is obvious why the event tree/fault tree approach has been adopted. Typical event trees are quite complex in nature, and the event tree/fault tree approach provides a systematic and organized approach to reliability analysis. The purpose of this study was two fold. Firstly, we wanted to explore the possibility that a semi-Markov process can create dependencies between sojourn times (the times it takes to transition from one state to the next) that can decrease the uncertainty when estimating time to failures. Using a generalized semi-Markov model, we studied a four element reliability model and were able to demonstrate such sojourn time dependencies. Secondly, we wanted to study the use of semi-Markov processes to introduce a time variable into the event tree diagrams that are commonly developed in PRA (Probabilistic Risk Assessment) analyses. Event tree end states which change with time are more representative of failure scenarios than are the usual static probability-derived end states.

  6. Electrostatic interaction of neutral semi-permeable membranes

    NASA Astrophysics Data System (ADS)

    Vinogradova, Olga I.; Bocquet, Lyderic; Bogdanov, Artem N.; Tsekov, Roumen; Lobaskin, Vladimir

    2012-01-01

    We consider an osmotic equilibrium between bulk solutions of polyelectrolyte bounded by semi-permeable membranes and separated by a thin film of salt-free liquid. Although the membranes are neutral, the counter-ions of the polyelectrolyte molecules permeate into the gap and lead to a steric charge separation. This gives rise to a distance-dependent membrane potential, which translates into a repulsive electrostatic disjoining pressure. From the solution of the nonlinear Poisson-Boltzmann equation, we obtain the distribution of the potential and of ions. We then derive an explicit formula for the pressure exerted on the membranes and show that it deviates from the classical van't Hoff expression for the osmotic pressure. This difference is interpreted in terms of a repulsive electrostatic disjoining pressure originating from the overlap of counterion clouds inside the gap. We also develop a simplified theory based on a linearized Poisson-Boltzmann approach. A comparison with simulation of a primitive model for the electrolyte is provided and does confirm the validity of the theoretical predictions. Beyond the fundamental result that the neutral surfaces can repel, this mechanism not only helps to control the adhesion and long-range interactions of living cells, bacteria, and vesicles, but also allows us to argue that electrostatic interactions should play enormous role in determining behavior and functions of systems bounded by semi-permeable membranes.

  7. Semi-Supervised Video Segmentation Using Tree Structured Graphical Models.

    PubMed

    Badrinarayanan, Vijay; Budvytis, Ignas; Cipolla, Roberto

    2013-03-06

    We present a novel patch-based probabilistic graphical model for semi-supervised video segmentation. At the heart of our model is a temporal tree structure which links patches in adjacent frames through the video sequence. This permits exact inference of pixel labels without resorting to traditional short time-window based video processing or instantaneous decision making. The input to our algorithm are labelled key frame(s) of a video sequence and the output is pixel-wise labels along with their confidences. We propose an efficient inference scheme that performs exact inference over the temporal tree, and optionally a per frame label smoothing step using loopy BP, to estimate pixel-wise labels and their posteriors. These posteriors are used to learn pixel unaries by training a Random Decision Forest in a semi-supervised manner. These unaries are used in a second iteration of label inference to improve the segmentation quality. We demonstrate the efficacy of our proposed algorithm using several qualitative and quantitative tests on both foreground/background and multi-class video segmentation problems using publicly available and our own datasets.

  8. Semi-supervised video segmentation using tree structured graphical models.

    PubMed

    Badrinarayanan, Vijay; Budvytis, Ignas; Cipolla, Roberto

    2013-11-01

    We present a novel patch-based probabilistic graphical model for semi-supervised video segmentation. At the heart of our model is a temporal tree structure that links patches in adjacent frames through the video sequence. This permits exact inference of pixel labels without resorting to traditional short time window-based video processing or instantaneous decision making. The input to our algorithm is labeled key frame(s) of a video sequence and the output is pixel-wise labels along with their confidences. We propose an efficient inference scheme that performs exact inference over the temporal tree, and optionally a per frame label smoothing step using loopy BP, to estimate pixel-wise labels and their posteriors. These posteriors are used to learn pixel unaries by training a Random Decision Forest in a semi-supervised manner. These unaries are used in a second iteration of label inference to improve the segmentation quality. We demonstrate the efficacy of our proposed algorithm using several qualitative and quantitative tests on both foreground/background and multiclass video segmentation problems using publicly available and our own datasets.

  9. Semi-dynamical perturbations of unified dark energy

    SciTech Connect

    Lombriser, Lucas; Taylor, Andy E-mail: ant@roe.ac.uk

    2015-11-01

    Linear cosmological perturbations of a large class of modified gravity and dark energy models can be unified in the effective field theory of cosmic acceleration, encompassing Horndeski scalar-tensor theories and beyond. The fully available model space inherent to this formalism cannot be constrained by measurements in the quasistatic small-scale regime alone. To facilitate the analysis of modifications from the concordance model beyond this limit, we introduce a semi-dynamical treatment extrapolated from the evolution of perturbations at a pivot scale of choice. At small scales, and for Horndeski theories, the resulting modifications recover a quasistatic approximation but account for corrections to it near the Hubble scale. For models beyond Horndeski gravity, we find that the velocity field and time derivative of the spatial metric potential can generally not be neglected, even in the small-scale limit. We test the semi-dynamical approximation against the linear perturbations of a range of dark energy and modified gravity models, finding good agreement between the two.

  10. Semi-Supervised Nonnegative Matrix Factorization via Constraint Propagation.

    PubMed

    Wang, Di; Gao, Xinbo; Wang, Xiumei

    2016-01-01

    As is well known, nonnegative matrix factorization (NMF) is a popular nonnegative dimensionality reduction method which has been widely used in computer vision, document clustering, and image analysis. However, traditional NMF is an unsupervised learning mode which cannot fully utilize the priori or supervised information. To this end, semi-supervised NMF methods have been proposed by incorporating the given supervised information. Nevertheless, when little supervised information is available, the improved performance will be limited. To effectively utilize the limited supervised information, this paper proposed a novel semi-supervised NMF method (CPSNMF) with pairwise constraints. The method propagates both the must-link and cannot-link constraints from the constrained samples to unconstrained samples, so that we can get the constraint information of the entire data set. Then, this information is reflected to the adjustment of data weight matrix. Finally, the weight matrix is incorporated as a regularization term to the NMF objective function. Therefore, the proposed method can fully utilize the constraint information to keep the geometry of the data distribution. Furthermore, the proposed CPSNMF is explored with two formulations and corresponding update rules are provided to solve the optimization problems. Thorough experiments on standard databases show the superior performance of the proposed method.

  11. Relaxation mechanisms, structure and properties of semi-coherent interfaces

    DOE PAGES

    Shao, Shuai; Wang, Jian

    2015-10-15

    In this work, using the Cu–Ni (111) semi-coherent interface as a model system, we combine atomistic simulations and defect theory to reveal the relaxation mechanisms, structure, and properties of semi-coherent interfaces. By calculating the generalized stacking fault energy (GSFE) profile of the interface, two stable structures and a high-energy structure are located. During the relaxation, the regions that possess the stable structures expand and develop into coherent regions; the regions with high-energy structure shrink into the intersection of misfit dislocations (nodes). This process reduces the interface excess potential energy but increases the core energy of the misfit dislocations and nodes.more » The core width is dependent on the GSFE of the interface. The high-energy structure relaxes by relative rotation and dilatation between the crystals. The relative rotation is responsible for the spiral pattern at nodes. The relative dilatation is responsible for the creation of free volume at nodes, which facilitates the nodes’ structural transformation. Several node structures have been observed and analyzed. In conclusion, the various structures have significant impact on the plastic deformation in terms of lattice dislocation nucleation, as well as the point defect formation energies.« less

  12. Phosphorus metabolic disorder of Guizhou semi-fine wool sheep.

    PubMed

    Shen, Xiaoyun; Zhang, Jinhua; Zhang, Renduo

    2014-01-01

    Guizhou semi-fine wool sheep are affected by a disease, characterized by emaciation, lameness, stiffness in the gait, enlargement of the costochondral junctions, and abnormal curvature in the long bones. The objective of this study was to determine possible relationships between the disease and mineral deficiencies. Samples of tissue and blood were collected from affected and unaffected sheep. Samples of soil and forage were collected from affected and unaffected areas. The samples were used for biochemical analyses and mineral nutrient measurements. Results showed that phosphorus (P) concentrations in forage samples from affected areas were significantly lower than those from unaffected areas (P < 0.01) and the mean ratio of calcium (Ca) to P in the affected forage was 12:1. Meanwhile, P concentrations of blood, bone, tooth, and wool from the affected sheep were also significantly lower than those from the unaffected group (P < 0.01). Serum P levels of the affected animals were much lower than those of the unaffected ones, whereas serum alkaline phosphatase levels from the affected were significantly higher than those from the unaffected (P < 0.01). Inorganic P levels of the affected sheep were about half of those in the control group. Oral administration of disodium hydrogen phosphate prevented and cured the disease. The study clearly demonstrated that the disease of Guizhou semi-fine wool sheep was mainly caused by the P deficiency in forage, as a result of fenced pasture and animal habitat fragmentation.

  13. Significant accumulation of nitrate in Chinese semi-humid croplands

    NASA Astrophysics Data System (ADS)

    Zhou, Junyu; Gu, Baojing; Schlesinger, William H.; Ju, Xiaotang

    2016-04-01

    Soil nitrate is important for crop growth, but it can also leach to groundwater causing nitrate contamination, a threat to human health. Here, we report a significant accumulation of soil nitrate in Chinese semi-humid croplands based upon more than 7000 samples from 141 sites collected from 1994 to 2015. In the 0–4 meters depth of soil, total nitrate accumulation reaches 453 ± 39, 749 ± 75, 1191 ± 89, 1269 ± 114, 2155 ± 330 kg N ha‑1 on average in wheat, maize, open-field vegetables (OFV), solar plastic-roofed greenhouse vegetables (GHV) and orchard fields, respectively. Surprisingly, there is also a comparable amount of nitrate accumulated in the vadose-zone deeper than 4 meters. Over-use of N fertilizer (and/or manure) and a declining groundwater table are the major causes for this huge nitrate reservoir in the vadose-zone of semi-humid croplands, where the nitrate cannot be denitrified due to the presence of oxygen and lack of carbon sources. Future climatic change with more extreme rainfall events would increase the risk of accumulated nitrate moving downwards and threatening groundwater nitrate contamination.

  14. Semi-analytical computation of displacement in linear viscoelastic materials

    NASA Astrophysics Data System (ADS)

    Spinu, S.; Gradinaru, D.

    2015-11-01

    Prediction of mechanical contact performance based on elastic models is not accurate in case of viscoelastic materials; however, a closed-form description of the viscoelastic contact has yet to be found. This paper aims to advance a semi-analytical method for computation of displacement induced in viscoelastic materials by arbitrary surface tractions, as a prerequisite to a semi-analytical solution for the viscoelastic contact problem. The newly advanced model is expected to provide greater generality, allowing for arbitrary contact geometry and / or arbitrary loading history. While time-independent equations in the purely elastic model can be treated numerically by imposing a spatial discretization only, a viscoelastic constitutive law requires supplementary temporal discretization capable of simulating the memory effect specific to viscoelastic materials. By deriving new influence coefficients, computation of displacement induced in a viscoelastic material by a known but otherwise arbitrary history of surface tractions can be achieved via superposition authorized by the Boltzmann superposition theory applicable in the frame of linear viscoelasticity.

  15. Significant accumulation of nitrate in Chinese semi-humid croplands

    PubMed Central

    Zhou, Junyu; Gu, Baojing; Schlesinger, William H.; Ju, Xiaotang

    2016-01-01

    Soil nitrate is important for crop growth, but it can also leach to groundwater causing nitrate contamination, a threat to human health. Here, we report a significant accumulation of soil nitrate in Chinese semi-humid croplands based upon more than 7000 samples from 141 sites collected from 1994 to 2015. In the 0–4 meters depth of soil, total nitrate accumulation reaches 453 ± 39, 749 ± 75, 1191 ± 89, 1269 ± 114, 2155 ± 330 kg N ha−1 on average in wheat, maize, open-field vegetables (OFV), solar plastic-roofed greenhouse vegetables (GHV) and orchard fields, respectively. Surprisingly, there is also a comparable amount of nitrate accumulated in the vadose-zone deeper than 4 meters. Over-use of N fertilizer (and/or manure) and a declining groundwater table are the major causes for this huge nitrate reservoir in the vadose-zone of semi-humid croplands, where the nitrate cannot be denitrified due to the presence of oxygen and lack of carbon sources. Future climatic change with more extreme rainfall events would increase the risk of accumulated nitrate moving downwards and threatening groundwater nitrate contamination. PMID:27114032

  16. Semi-supervised hashing for large-scale search.

    PubMed

    Wang, Jun; Kumar, Sanjiv; Chang, Shih-Fu

    2012-12-01

    Hashing-based approximate nearest neighbor (ANN) search in huge databases has become popular due to its computational and memory efficiency. The popular hashing methods, e.g., Locality Sensitive Hashing and Spectral Hashing, construct hash functions based on random or principal projections. The resulting hashes are either not very accurate or are inefficient. Moreover, these methods are designed for a given metric similarity. On the contrary, semantic similarity is usually given in terms of pairwise labels of samples. There exist supervised hashing methods that can handle such semantic similarity, but they are prone to overfitting when labeled data are small or noisy. In this work, we propose a semi-supervised hashing (SSH) framework that minimizes empirical error over the labeled set and an information theoretic regularizer over both labeled and unlabeled sets. Based on this framework, we present three different semi-supervised hashing methods, including orthogonal hashing, nonorthogonal hashing, and sequential hashing. Particularly, the sequential hashing method generates robust codes in which each hash function is designed to correct the errors made by the previous ones. We further show that the sequential learning paradigm can be extended to unsupervised domains where no labeled pairs are available. Extensive experiments on four large datasets (up to 80 million samples) demonstrate the superior performance of the proposed SSH methods over state-of-the-art supervised and unsupervised hashing techniques.

  17. Detecting Emergent Behaviors with Semi-Boolean Algebra

    SciTech Connect

    Haglich, Peter; Rouff, Christopher; Pullum, Laura L

    2010-01-01

    As systems continue to be interconnected, their collective behavior becomes increasingly difficult to predict. The emergent properties of systems of systems make them powerful, but at the same time make them more difficult to design, assure proper behaviors emerge, operate correctly, and have no new security holes. Learning and adaptation cause additional concerns because emergent behavior patterns simply cannot be fully predicted through the use of traditional system development methods, such as testing and model checking. In addition, self-organization can occur as the individual systems optimize to address inefficiencies in the larger system. Designing for and detecting emergent behavior is something that has not been addressed in current systems development methodologies. This paper gives background on approaches for modeling and verifying emergent behavior and then discusses the use of semi-Boolean algebra as a means for detecting emergence in combined behaviors. Semi-Boolean algebra is a generalization of the Boolean algebra concept obtained by weakening the requirement that any two elements have a common upper bound. An example is given and several ways are described that allow emergent behavior to be detected with this technique.

  18. Development of Semi-Span Model Test Techniques

    NASA Technical Reports Server (NTRS)

    Milholen, William E., II; Chokani, Ndaona; McGhee, Robert J.

    1996-01-01

    A computational investigation was performed to support the development of a semispan model test capability in the NASA Langley Research Center's National Transonic Facility. This capability is desirable for the testing of advanced subsonic transport aircraft at full-scale Reynolds numbers. A state-of-the-art three-dimensional Navier-Stokes solver was used to examine methods to improve the flow over a semi-span configuration. First, a parametric study is conducted to examine the influence of the stand-off height on the flow over the semispan model. It is found that decreasing the stand-off height, below the maximum fuselage radius, improves the aerodynamic characteristics of the semi-span model. Next, active sidewall boundary layer control techniques are examined. Juncture region blowing jets, upstream tangential blowing, and sidewall suction are found to improve the flow over the aft portion of the semispan model. Both upstream blowing and suction are found to reduce the sidewall boundary layer separation. The resulting near surface streamline patterns are improved, and found to be quite similar to the full-span results. Both techniques however adversely affect the pitching moment coefficient.

  19. Drop impact onto semi-infinite solid surface

    NASA Astrophysics Data System (ADS)

    Chen, Huanchen; Amirfazli, Alidad

    2016-11-01

    The drop impact onto solid surfaces has been studied intensively due to its importance in different applications, e.g. spray coating, inkjet printing and agricultural sprays. The previous studies on this topic were typically focused either on the drop impact onto an infinite solid surface (i.e. a solid surface that is large, and the impact happens far away from the surface edges), or onto a finite solid surface (e.g. drop impact onto a target smaller than the droplet). However, in practice, it is also possible for the impact onto a large surface but close to its edge (named as semi-infinite surface). In this first study of its kind, the process of drop impact onto a semi-infinite surface (both hydrophobic and hydrophilic) was investigated experimentally. During the impact process, part of the liquid lamella can spread out of the surface (free lamella). Depending on the distance between the impact point and surface edge, the free lamella can recede, or partially recede back to the surface, or completely break apart at the surface edge. The behavior of free lamella can also affect the morphology of the part of liquid lamella which remains in contact with the solid surface, especially in the receding phase (e.g. occurrence of drop rebound). Various morphologies observed for lamella breakage at the surface edge will also be discussed for surfaces of different wettabilities.

  20. Spectra of Semi-Infinite Quantum Graph Tubes

    NASA Astrophysics Data System (ADS)

    Shipman, Stephen P.; Tillay, Jeremy

    2016-10-01

    The spectrum of a semi-infinite quantum graph tube with square period cells is analyzed. The structure is obtained by rolling up a doubly periodic quantum graph into a tube along a period vector and then retaining only a semi-infinite half of the tube. The eigenfunctions associated to the spectrum of the half-tube involve all Floquet modes of the full tube. This requires solving the complex dispersion relation {D(λ,k_1,k_2)=0} with {(k_1,k_2)in({C}/2π{Z})^2} subject to the constraint {a k_1 + b k_2 ≡ 0} (mod {2π}), where a and b are integers. The number of Floquet modes for a given {λin{R}} is {2max{ a, b }}. Rightward and leftward modes are determined according to an indefinite energy flux form. The spectrum may contain eigenvalues that depend on the boundary conditions, and some eigenvalues may be embedded in the continuous spectrum.

  1. DREAM: a method for semi-quantitative dermal exposure assessment.

    PubMed

    Van-Wendel-de-Joode, Berna; Brouwer, Derk H; Vermeulen, Roel; Van Hemmen, Joop J; Heederik, Dick; Kromhout, Hans

    2003-01-01

    This paper describes a new method (DREAM) for structured, semi-quantitative dermal exposure assessment for chemical or biological agents that can be used in occupational hygiene or epidemiology. It is anticipated that DREAM could serve as an initial assessment of dermal exposure, amongst others, resulting in a ranking of tasks and subsequently jobs. DREAM consists of an inventory and evaluation part. Two examples of dermal exposure of workers of a car-construction company show that DREAM characterizes tasks and gives insight into exposure mechanisms, forming a basis for systematic exposure reduction. DREAM supplies estimates for exposure levels on the outside clothing layer as well as on skin, and provides insight into the distribution of dermal exposure over the body. Together with the ranking of tasks and people, this provides information for measurement strategies and helps to determine who, where and what to measure. In addition to dermal exposure assessment, the systematic description of dermal exposure pathways helps to prioritize and determine most adequate measurement strategies and methods. DREAM could be a promising approach for structured, semi-quantitative, dermal exposure assessment.

  2. Estimation in a semi-Markov transformation model

    PubMed Central

    Dabrowska, Dorota M.

    2012-01-01

    Multi-state models provide a common tool for analysis of longitudinal failure time data. In biomedical applications, models of this kind are often used to describe evolution of a disease and assume that patient may move among a finite number of states representing different phases in the disease progression. Several authors developed extensions of the proportional hazard model for analysis of multi-state models in the presence of covariates. In this paper, we consider a general class of censored semi-Markov and modulated renewal processes and propose the use of transformation models for their analysis. Special cases include modulated renewal processes with interarrival times specified using transformation models, and semi-Markov processes with with one-step transition probabilities defined using copula-transformation models. We discuss estimation of finite and infinite dimensional parameters of the model, and develop an extension of the Gaussian multiplier method for setting confidence bands for transition probabilities. A transplant outcome data set from the Center for International Blood and Marrow Transplant Research is used for illustrative purposes. PMID:22740583

  3. Semi-structured meshes for axial turbomachinery blades

    NASA Astrophysics Data System (ADS)

    Sbardella, L.; Sayma, A. I.; Imregun, M.

    2000-03-01

    This paper describes the development and application of a novel mesh generator for the flow analysis of turbomachinery blades. The proposed method uses a combination of structured and unstructured meshes, the former in the radial direction and the latter in the axial and tangential directions, in order to exploit the fact that blade-like structures are not strongly three-dimensional since the radial variation is usually small. The proposed semi-structured mesh formulation was found to have a number of advantages over its structured counterparts. There is a significant improvement in the smoothness of the grid spacing and also in capturing particular aspects of the blade passage geometry. It was also found that the leading- and trailing-edge regions could be discretized without generating superfluous points in the far field, and that further refinements of the mesh to capture wake and shock effects were relatively easy to implement. The capability of the method is demonstrated in the case of a transonic fan blade for which the steady state flow is predicted using both structured and semi-structured meshes. A totally unstructured mesh is also generated for the same geometry to illustrate the disadvantages of using such an approach for turbomachinery blades. Copyright

  4. Relaxation mechanisms, structure and properties of semi-coherent interfaces

    SciTech Connect

    Shao, Shuai; Wang, Jian

    2015-10-15

    In this work, using the Cu–Ni (111) semi-coherent interface as a model system, we combine atomistic simulations and defect theory to reveal the relaxation mechanisms, structure, and properties of semi-coherent interfaces. By calculating the generalized stacking fault energy (GSFE) profile of the interface, two stable structures and a high-energy structure are located. During the relaxation, the regions that possess the stable structures expand and develop into coherent regions; the regions with high-energy structure shrink into the intersection of misfit dislocations (nodes). This process reduces the interface excess potential energy but increases the core energy of the misfit dislocations and nodes. The core width is dependent on the GSFE of the interface. The high-energy structure relaxes by relative rotation and dilatation between the crystals. The relative rotation is responsible for the spiral pattern at nodes. The relative dilatation is responsible for the creation of free volume at nodes, which facilitates the nodes’ structural transformation. Several node structures have been observed and analyzed. In conclusion, the various structures have significant impact on the plastic deformation in terms of lattice dislocation nucleation, as well as the point defect formation energies.

  5. Semi-automatic object geometry estimation for image personalization

    NASA Astrophysics Data System (ADS)

    Ding, Hengzhou; Bala, Raja; Fan, Zhigang; Eschbach, Reiner; Bouman, Charles A.; Allebach, Jan P.

    2010-01-01

    Digital printing brings about a host of benefits, one of which is the ability to create short runs of variable, customized content. One form of customization that is receiving much attention lately is in photofinishing applications, whereby personalized calendars, greeting cards, and photo books are created by inserting text strings into images. It is particularly interesting to estimate the underlying geometry of the surface and incorporate the text into the image content in an intelligent and natural way. Current solutions either allow fixed text insertion schemes into preprocessed images, or provide manual text insertion tools that are time consuming and aimed only at the high-end graphic designer. It would thus be desirable to provide some level of automation in the image personalization process. We propose a semi-automatic image personalization workflow which includes two scenarios: text insertion and text replacement. In both scenarios, the underlying surfaces are assumed to be planar. A 3-D pinhole camera model is used for rendering text, whose parameters are estimated by analyzing existing structures in the image. Techniques in image processing and computer vison such as the Hough transform, the bilateral filter, and connected component analysis are combined, along with necessary user inputs. In particular, the semi-automatic workflow is implemented as an image personalization tool, which is presented in our companion paper.1 Experimental results including personalized images for both scenarios are shown, which demonstrate the effectiveness of our algorithms.

  6. Literature classification for semi-automated updating of biological knowledgebases

    PubMed Central

    2013-01-01

    Background As the output of biological assays increase in resolution and volume, the body of specialized biological data, such as functional annotations of gene and protein sequences, enables extraction of higher-level knowledge needed for practical application in bioinformatics. Whereas common types of biological data, such as sequence data, are extensively stored in biological databases, functional annotations, such as immunological epitopes, are found primarily in semi-structured formats or free text embedded in primary scientific literature. Results We defined and applied a machine learning approach for literature classification to support updating of TANTIGEN, a knowledgebase of tumor T-cell antigens. Abstracts from PubMed were downloaded and classified as either "relevant" or "irrelevant" for database update. Training and five-fold cross-validation of a k-NN classifier on 310 abstracts yielded classification accuracy of 0.95, thus showing significant value in support of data extraction from the literature. Conclusion We here propose a conceptual framework for semi-automated extraction of epitope data embedded in scientific literature using principles from text mining and machine learning. The addition of such data will aid in the transition of biological databases to knowledgebases. PMID:24564403

  7. A semi-empirical airfoil stall noise model based on surface pressure measurements

    NASA Astrophysics Data System (ADS)

    Bertagnolio, Franck; Madsen, Helge Aa.; Fischer, Andreas; Bak, Christian

    2017-01-01

    This work is concerned with the experimental study of airfoil stall and the modelling of stall noise. Using pressure taps and high-frequency surface pressure microphones flush-mounted on airfoils measured in wind tunnels and on an operating wind turbine blade, the characteristics of stall are analyzed. This study shows that the main quantities of interest, namely convection velocity, spatial correlation and surface pressure spectra, can be scaled highlighting the universal nature of stall independently of airfoil shapes and flow conditions, although within a certain range of experimental conditions. Two main regimes for the scaling of the correlation lengths and the surface pressure spectra, depending on the Reynolds number of the flow, can be distinguished. These results are used to develop a model for the surface pressure spectra within the detached flow region valid for Reynolds numbers ranging from 1 ×106 to 6 ×106. Subsequently, this model is used to derive a model for stall noise. Modelled noise spectra are compared with experimental data measured in anechoic wind tunnels with reasonably satisfactory agreement.

  8. Semi-external mixing: Effect on polluted dust optics

    NASA Astrophysics Data System (ADS)

    Mishra, S. K.; Tripathi, S. N.; Aggarwal, S. G.; Arola, A. T.

    2011-12-01

    The uncertainty in the radiative forcing for the mineral dust is very high among all the aerosol systems (Forster et al., 2007). The uncertainty may further enhance due to mixing of pure mineral dust with other carbonaceous species like black carbon and organic carbon. So, the emphasis should be given for modeling/observation of polluted dust optics. The mineral dust is found to mix with the carbonaceous pollutants in the atmosphere, semi-externally (Li et al., 2010; Alexander et al., 2008). To date, the effect of semi-external mixing on the dust optics has never been studied in detail. In present study, we consider that the pure mineral dust comprises of non-metallic components and metallic component such as hematite, Fe2O3 (Mishra and Tripathi, 2008). Hematite is the key component which governs the absorbance of pure dust. It has been constrained between 0-8%. For modeling polluted dust optics, the considered model shapes are three sphere, two sphere and two spheroid particle system where mineral dust is shown to mix with organic carbon, OC (comprising of HUmic-Like Substances, HULIS), brown carbon, BrC and black carbon, BC by making a semi-external mixture. The Discrete Dipole Approximation, DDA code has been used for modeling optical properties (e.g. Single Scattering Albedo, SSA; Asymmetry parameter, g and Extinction efficiency, Qext) of above model shapes for the polluted dust. The SSA was found to vary with hematite content and heterogeneous combinations. The deviation in size averaged SSA relative to D-4 and D-8 (dust spheres with 4% and 8% hematite, respectively) sphere is found to be maximum for the particle system BCBCBC (three black carbon spheres attached to each other) (i.e. 50% and 47%, respectively) followed by BrCBrCBrC (three brown carbon spheres attached to each other) (i.e. 45% and 42%, respectively) and BCBCD (two black carbon spheres attached to one dust sphere) (i.e. 37% and 32%, respectively). For the Asian region (the pollution-prone zone

  9. A Terminal Guidance Model for Smart Projectiles Employing a Semi-Active Laser Seeker

    DTIC Science & Technology

    2011-08-01

    A Terminal Guidance Model for Smart Projectiles Employing a Semi-Active Laser Seeker by Luke S. Strohm ARL-TR-5654 August 2011...Terminal Guidance Model for Smart Projectiles Employing a Semi-Active Laser Seeker Luke S. Strohm Weapons and Materials Research Directorate...January 2010–31 March 2011 4. TITLE AND SUBTITLE A Terminal Guidance Model for Smart Projectiles Employing a Semi-Active Laser Seeker 5a. CONTRACT

  10. Deformation of Semi-Solid Metals - Refining, Strengthening, and Rheological Behavior.

    DTIC Science & Technology

    1982-07-15

    described. This work extends earlier studies on " Rheocasting " and has broad, practical implications. The original Rheocast work, sponsored by ARO, led to... Rheocasting has now finally become a commercial reality. The broad area of forming and otherwise processing of metals in the semi-solid state is one that...than Rheocasting , for forming metals in their semi-solid state. And we wondered as well if we might find some way, through deformation in the semi-solid

  11. Sequential organization and optimization of the nut-cracking behavior of semi-free tufted capuchin monkeys (Sapajus sp.).

    PubMed

    Corat, Clara; Siqueira, José; Ottoni, Eduardo B

    2016-01-01

    Stone-aided nut-cracking requires the coordination of three elements: the agent must assemble nuts, a "hammer" stone and an "anvil." Under naturalistic settings, nut-cracking sites, constituted of anvil-like surfaces and already containing a hammer stone, can be fairly stable, lasting as long as the "hammer" stays in place. In an experiment with a semi-free-ranging group of tufted capuchin monkeys (Sapajus sp.) we observed the behavioral sequences leading to nut-cracking. We positioned nuts, hammer, and anvil at the vertices of a 10-m-sided equilateral triangle. Thus, to crack a nut the individuals had to visit the vertices and gather the movable elements (nut and hammer) at the anvil. Under such conditions, the monkeys systematically employed a nut-hammer-anvil vertex visit sequence, one of the shortest and more cost-effective possible routes. In the following experiment, we examined whether the gathering of the hammer after the nuts resulted solely from a "nut first" strategy or if the monkeys were also minimizing hammer transport costs. We positioned two hammers, of the same weight, at different distances from the nuts and anvil, so the cost of hammer transportation (energy and risk of injury) would be higher or lower depending on the choice of hammer (the hammer closer to the nuts being farther from the anvil). We found that, instead of collecting the closest hammer, after collecting the nut, the monkeys systematically chose the hammer closer to (and beyond) the anvil, thus minimizing transport costs.

  12. Bessel-Weighted Asymmetries in Semi Inclusive Deep Inelastic Scattering

    SciTech Connect

    D. Boer, L. Gamberg, B.U. Musch, A. Prokudin

    2011-10-01

    The concept of weighted asymmetries is revisited for semi-inclusive deep inelastic scattering. We consider the cross section in Fourier space, conjugate to the outgoing hadron's transverse momentum, where convolutions of transverse momentum dependent parton distribution functions and fragmentation functions become simple products. Individual asymmetric terms in the cross section can be projected out by means of a generalized set of weights involving Bessel functions. Advantages of employing these Bessel weights are that they suppress (divergent) contributions from high transverse momentum and that soft factors cancel in (Bessel-) weighted asymmetries. Also, the resulting compact expressions immediately connect to previous work on evolution equations for transverse momentum dependent parton distribution and fragmentation functions and to quantities accessible in lattice QCD. Bessel weighted asymmetries are thus model independent observables that augment the description and our understanding of correlations of spin and momentum in nucleon structure.

  13. Galacticus: A Semi-Analytic Model of Galaxy Formation

    NASA Astrophysics Data System (ADS)

    Benson, Andrew

    2011-08-01

    Galacticus is designed to solve the physics involved in the formation of galaxies within the current standard cosmological framework. It is of a type of model known as “semi-analytic” in which the numerous complex non-linear physics involved are solved using a combination of analytic approximations and empirical calibrations from more detailed, numerical solutions. Models of this type aim to begin with the initial state of the Universe (specified shortly after the Big Bang) and apply physical principles to determine the properties of galaxies in the Universe at later times, including the present day. Typical properties computed include the mass of stars and gas in each galaxy, broad structural properties (e.g. radii, rotation speeds, geometrical shape etc.), dark matter and black hole contents, and observable quantities such as luminosities, chemical composition etc.

  14. Reduction Of Sizes Of Semi-Markov Reliability Models

    NASA Technical Reports Server (NTRS)

    White, Allan L.; Palumbo, Dan L.

    1995-01-01

    Trimming technique reduces computational effort by order of magnitude while introducing negligible error. Error bound depends on only three parameters from semi-Markov model: maximum sum of rates for failure transitions leaving any state, maximum average holding time for recovery-mode state, and operating time for system. Error bound computed before any model generated, enabling modeler to decide immediately whether or not model can be trimmed. Trimming procedure specified by precise and easy description, making it easy to include trimming procedure in program generating mathematical models for use in assessing reliability. Typical application of technique in design of digital control systems required to be extremely reliable. In addition to aerospace applications, fault-tolerant design has growing importance in wide range of industrial applications.

  15. Prototype Vector Machine for Large Scale Semi-Supervised Learning

    SciTech Connect

    Zhang, Kai; Kwok, James T.; Parvin, Bahram

    2009-04-29

    Practicaldataminingrarelyfalls exactlyinto the supervisedlearning scenario. Rather, the growing amount of unlabeled data poses a big challenge to large-scale semi-supervised learning (SSL). We note that the computationalintensivenessofgraph-based SSLarises largely from the manifold or graph regularization, which in turn lead to large models that are dificult to handle. To alleviate this, we proposed the prototype vector machine (PVM), a highlyscalable,graph-based algorithm for large-scale SSL. Our key innovation is the use of"prototypes vectors" for effcient approximation on both the graph-based regularizer and model representation. The choice of prototypes are grounded upon two important criteria: they not only perform effective low-rank approximation of the kernel matrix, but also span a model suffering the minimum information loss compared with the complete model. We demonstrate encouraging performance and appealing scaling properties of the PVM on a number of machine learning benchmark data sets.

  16. On the semi-classical approximation to the superstring theory

    SciTech Connect

    Pollock, M.D. )

    1992-10-10

    In this paper, the semi-classical limit of the compactified, heterotic superstring theory is examined, including the effects of higher-derivative terms R[sup 2] in the effective Lagrangian. The total wave-function [Psi] obeys a Schrodinger equation in the mini-superspace ds[sup 2] = dt[sup 2] [minus] e[sup 2][alpha](t) dx[sup 2], the canonical coordinates being the position [alpha] and the velocity (Hubble parameter) [xi] [triple bond] [alpha], while the cosmic time coincides with the parameter introduced by Tomonaga, (derivative)/(derivative) [sigma] [triple bond] [xi] (derivative)/(derivative) [alpha]. The wave function describing the matter, [Psi][sub m], also obeys a linear Schrodinger equation.

  17. MODIS Science Team Member Semi-annual Report

    NASA Technical Reports Server (NTRS)

    Vermote, Eric; ElSaleous, Nazmi; Fisher, Paul; Karakos, Damianos; Ray, James; Vermeulen, Anne

    1998-01-01

    This paper presents a semi-annual report of the MODerate resolution imaging Spectroradiometer (MODIS) Science Team Members. The most important activities undertaken during this reporting period are the following: 1) Versions 2.1 and 2.2 surface reflectance L2/L3 DAAC/SDST delivery; 2) Version 2.0 1km and 250m VI product delivery (assist Arizona); 3) Version 2.1 surface reflectance L2 testing; 4) Land Synthetic data set generator improvements; 5) QA; 6) Surface reflectance error budget generation (SWAMP request); 7) SCF Hardware; 8) Aerosol transport modeling; 9) Aerosol optical depth retrieval from AVHRR data; 10) Aerosol characteristics retrieval from SeaWIFS/AVHRR fusioned data; 11) Validation activities; 12) Aerosol climatology; and 13) 6S code. The report includes summaries of the topics above.

  18. Beam-spin asymmetries from semi-inclusive pion electroproduction

    NASA Astrophysics Data System (ADS)

    Gohn, W.; Avakian, H.; Joo, K.; Ungaro, M.; Adhikari, K. P.; Aghasyan, M.; Amaryan, M. J.; Anderson, M. D.; Anefalos Pereira, S.; Ball, J.; Baltzell, N. A.; Battaglieri, M.; Biselli, A. S.; Bono, J.; Briscoe, W. J.; Brooks, W. K.; Burkert, V. D.; Carman, D. S.; Celentano, A.; Chandavar, S.; Charles, G.; Cole, P. L.; Contalbrigo, M.; Cortes, O.; Crede, V.; D'Angelo, A.; Dashyan, N.; De Vita, R.; De Sanctis, E.; Djalali, C.; Doughty, D.; Dupre, R.; El Alaoui, A.; El Fassi, L.; Eugenio, P.; Fedotov, G.; Fleming, J. A.; Forest, T.; Garçon, M.; Ghandilyan, Y.; Gilfoyle, G. P.; Giovanetti, K. L.; Girod, F. X.; Gothe, R. W.; Griffioen, K. A.; Guegan, B.; Guo, L.; Hafidi, K.; Hanretty, C.; Harrison, N.; Hattawy, Mohammad; Hicks, K.; Ho, D.; Holtrop, M.; Hyde, C.; Ilieva, Y.; Ireland, D. G.; Ishkhanov, B. S.; Jo, H. S.; Keller, D.; Khandaker, M.; Khetarpal, P.; Kim, W.; Klein, F. J.; Koirala, S.; Kubarovsky, V.; Kuhn, S. E.; Kuleshov, S. V.; Lenisa, P.; Livingston, K.; Lu, H. Y.; MacGregor, I. J. D.; Markov, N.; Mayer, M.; McKinnon, B.; Mineeva, T.; Mirazita, M.; Mokeev, V.; Movsisyan, A.; Nadel-Turonski, P.; Niccolai, S.; Niculescu, I.; Osipenko, M.; Ostrovidov, A. I.; Pappalardo, L. L.; Paremuzyan, R.; Park, K.; Pasyuk, E.; Peng, P.; Phillips, J. J.; Pisano, S.; Pozdniakov, S.; Price, J. W.; Procureur, S.; Prok, Y.; Puckett, A. J. R.; Raue, B. A.; Ripani, M.; Ritchie, B. G.; Rizzo, A.; Rosner, G.; Rossi, P.; Roy, P.; Sabatié, F.; Salgado, C.; Schott, D.; Schumacher, R. A.; Seder, E.; Seraydaryan, H.; Sharabian, Y. G.; Simonyan, A.; Smith, G. D.; Sober, D. I.; Sokhan, D.; Stoler, P.; Strakovsky, I. I.; Stepanyan, S.; Strauch, S.; Tang, W.; Tkachenko, S.; Vernarsky, B.; Voskanyan, H.; Voutier, E.; Walford, N. K.; Watts, D. P.; Weinstein, L. B.; Wood, M. H.; Zachariou, N.; Zana, L.; Zhang, J.; Zonta, I.; CLAS Collaboration

    2014-04-01

    We have measured the moment ALUsinϕ corresponding to the polarized electron beam-spin asymmetry in semi-inclusive deep inelastic scattering. ALUsinϕ is a twist-3 quantity providing information about quark-gluon correlations. Data were taken with the CLAS Spectrometer at Jefferson Lab using a 5.498 GeV longitudinally polarized electron beam and an unpolarized liquid hydrogen target. All three pion channels (π+, π0 and π-) were measured simultaneously over a large range of kinematics within the virtuality range Q2≈ 1.0-4.5 GeV2. The observable was measured with better than 1% statistical precision over a large range of z, PT, xB, and Q2, which permits comparison with several reaction models. The discussed measurements provide an upgrade in statistics over previous measurements, and serve as the first evidence for the negative sign of the π- sinϕ moment.

  19. Semi-spontaneous oral text production: measurements in clinical practice.

    PubMed

    Lind, Marianne; Kristoffersen, Kristian Emil; Moen, Inger; Simonsen, Hanne Gram

    2009-12-01

    Functionally relevant assessment of the language production of speakers with aphasia should include assessment of connected speech production. Despite the ecological validity of everyday conversations, more controlled and monological types of texts may be easier to obtain and analyse in clinical practice. This article discusses some simple measurements for the analysis of semi-spontaneous oral text production by speakers with aphasia. Specifically, the measurements are related to the production of verbs and nouns, and the realization of different sentence types. The proposed measurements should be clinically relevant, easily applicable, and linguistically meaningful. The measurements have been applied to oral descriptions of the 'Cookie Theft' picture by eight monolingual Norwegian speakers, four with an anomic type of aphasia and four without any type of language impairment. Despite individual differences in both the clinical and the non-clinical group, most of the measurements seem to distinguish between speakers with and without aphasia.

  20. SEMCARE: Multilingual Semantic Search in Semi-Structured Clinical Data.

    PubMed

    López-García, Pablo; Kreuzthaler, Markus; Schulz, Stefan; Scherr, Daniel; Daumke, Philipp; Markó, Kornél; Kors, Jan A; van Mulligen, Erik M; Wang, Xinkai; Gonna, Hanney; Behr, Elijah; Honrado, Ángel

    2016-01-01

    The vast amount of clinical data in electronic health records constitutes a great potential for secondary use. However, most of this content consists of unstructured or semi-structured texts, which is difficult to process. Several challenges are still pending: medical language idiosyncrasies in different natural languages, and the large variety of medical terminology systems. In this paper we present SEMCARE, a European initiative designed to minimize these problems by providing a multi-lingual platform (English, German, and Dutch) that allows users to express complex queries and obtain relevant search results from clinical texts. SEMCARE is based on a selection of adapted biomedical terminologies, together with Apache UIMA and Apache Solr as open source state-of-the-art natural language pipeline and indexing technologies. SEMCARE has been deployed and is currently being tested at three medical institutions in the UK, Austria, and the Netherlands, showing promising results in a cardiology use case.

  1. A semi-analytical Lagrangian dispersion model in inhomogeneous turbulence

    SciTech Connect

    Zhuang, Y.

    1996-12-31

    Probably the most natural method to describe turbulent dispersion in the atmosphere is the Lagrangian trajectory model. In this approach, one builds the joint probability density function (PDF) of particle velocity and position by following a large number of particle trajectories in a turbulent flow given the Eulerian flow statistics. The statistics of the concentration can then be found from the joint PDF. However, the usefulness of the Lagrangian trajectory model in practice has been hindered by the necessary lengthy and stochastic numerical calculations. As a result, few operational models based on the Lagrangian trajectory approach have been proposed. This paper reports the first attempt to solve the Fokker-Planck equation using the function expansion method. The semi-analytical solution retains the characteristics of the Lagrangian trajectory model, but takes little computation effort. The solutions for Gaussian inhomogeneous turbulence and skewed homogeneous turbulence are discussed by comparing them with those calculated using the trajectory simulation method.

  2. Quantifying macropore recharge: Examples from a semi-arid area

    USGS Publications Warehouse

    Wood, W.W.; Rainwater, K.A.; Thompson, D.B.

    1997-01-01

    The purpose of this paper is to illustrate the significantly increased resolution of determining macropore recharge by combining physical, chemical, and isotopic methods of analysis. Techniques for quantifying macropore recharge were developed for both small-scale (1 to 10 km2) and regional-scale areas in and semi-arid areas. The Southern High Plains region of Texas and New Mexico was used as a representative field site to test these methods. Macropore recharge in small-scale areas is considered to be the difference between total recharge through floors of topographically dosed basins and interstitial recharge through the same area. On the regional scale, macropore recharge was considered to be the difference between regional average annual recharge and interstitial recharge measured in the unsaturated zone. Stable isotopic composition of ground water and precipitation was used us an independent estimate of macropore recharge on the regional scale. Results of this analysis suggest that in the Southern High Plains recharge flux through macropores is between 60 and 80 percent of the total 11 mm/y. Between 15 and 35 percent of the recharge occurs by interstitial recharge through the basin floors. Approximately 5 percent of the total recharge occurs as either interstitial or matrix recharge between the basin floors, representing approximately 95 percent of the area. The approach is applicable to other arid and semi-arid areas that focus rainfall into depressions or valleys.The purpose of this paper is to illustrate the significantly increased resolution of determining macropore recharge by combining physical, chemical, and isotopic methods of analysis. Techniques for quantifying macropore recharge were developed for both small-scale (1 to 10 km2) and regional-scale areas in arid and semi-arid areas. The Southern High Plains region of Texas and New Mexico was used as a representative field site to test these methods. Macropore recharge in small-scale areas is considered

  3. CP violation in Semi-Leptonic {tau} decays

    SciTech Connect

    Delepine, David

    2007-06-19

    We study CP violation in semi-leptonic {tau} decays and we determine the conditions necessary to be able to define a observable CP asymmetry. We apply these conditions in both models, the standard model for the electroweak interactions and its supersymmetric extensions. In the first case, the leading order contribution to the direct CP asymmetry in {tau}{+-} {yields} K{+-}{pi}0{nu}{tau} decay rates is evaluated. In the second case,we compute the SUSY effective hamiltonian that describes the |{delta}S| = 1 semileptonic decays of tau leptons. We show that SUSY contributions may enhance the CP asymmetry of {tau} {yields} K{pi}{nu}{tau} decays by several orders of magnitude compared to the standard model expectations.

  4. Review of semi-classical calculations for breakup

    SciTech Connect

    Baye, Daniel

    2005-10-14

    In semi-classical approximations, the relative motion between target and projectile is represented by a classical trajectory but the projectile internal motion is treated quantum mechanically. A time-dependent Schroedinger equation describes the breakup of exotic nuclei induced by the Coulomb and nuclear forces. Different accurate techniques of resolution of this time-dependent equation are reviewed for one space dimension. The respective merits of their extensions to three dimensions are compared. Applications to the breakup of the 11Be, 15C, and 19C halo nuclei are presented and discussed. The first-order perturbation theory is compared with the time-dependent method and its relevance for the Coulomb breakup determination of the astrophysical S factor is analyzed.

  5. A missing data approach to semi-competing risks problems.

    PubMed

    Dignam, James J; Wieand, Kelly; Rathouz, Paul J

    2007-02-20

    For event time data involving multiple mutually exclusive competing causes of failure, classic competing risks results show that marginal survival distributions are not identifiable. In a related instance, one or more failure modes may be observed provided that the failure events occur in a specific order. In such situations, sometimes referred to as semi-competing risks problems, the observations may under realistic assumptions lend information about parameters of interest that would be nonidentifiable in the strict competing risks case. Here, we present an approach that makes use of partially observable multiple modes of failures to obtain an estimate of the marginal distribution of one event type that may occur prior to the occurrence of another event type or be precluded by it. We apply the proposed method to the problem of estimating the distribution of time to tumour recurrence at specific sites among breast cancer patients participating in randomized clinical trials.

  6. Characteristics of a semi-custom library development system

    NASA Technical Reports Server (NTRS)

    Yancey, M.; Cannon, R.

    1990-01-01

    Standard cell and gate array macro libraries are in common use with workstation computer aided design (CAD) tools for application specific integrated circuit (ASIC) semi-custom application and have resulted in significant improvements in the overall design efficiencies as contrasted with custom design methodologies. Similar design methodology enhancements in providing for the efficient development of the library cells is an important factor in responding to the need for continuous technology improvement. The characteristics of a library development system that provides design flexibility and productivity enhancements for the library development engineer as he provides libraries in the state-of-the-art process technologies are presented. An overview of Gould's library development system ('Accolade') is also presented.

  7. Semi-physical neural modeling for linear signal restoration.

    PubMed

    Bourgois, Laurent; Roussel, Gilles; Benjelloun, Mohammed

    2013-02-01

    This paper deals with the design methodology of an Inverse Neural Network (INN) model. The basic idea is to carry out a semi-physical model gathering two types of information: the a priori knowledge of the deterministic rules which govern the studied system and the observation of the actual conduct of this system obtained from experimental data. This hybrid model is elaborated by being inspired by the mechanisms of a neuromimetic network whose structure is constrained by the discrete reverse-time state-space equations. In order to validate the approach, some tests are performed on two dynamic models. The first suggested model is a dynamic system characterized by an unspecified r-order Ordinary Differential Equation (ODE). The second one concerns in particular the mass balance equation for a dispersion phenomenon governed by a Partial Differential Equation (PDE) discretized on a basic mesh. The performances are numerically analyzed in terms of generalization, regularization and training effort.

  8. Semi-inclusive charged-current neutrino-nucleus reactions

    SciTech Connect

    Moreno, O.; Donnelly, T. W.; Van Orden, J. W.; Ford, W. P.

    2014-07-17

    The general, universal formalism for semi-inclusive charged-current (anti)neutrino-nucleus reactions is given for studies of any hadronic system, namely, either nuclei or the nucleon itself. The detailed developments are presented with the former in mind and are further specialized to cases where the final-state charged lepton and an ejected nucleon are presumed to be detected. General kinematics for such processes are summarized and then explicit expressions are developed for the leptonic and hadronic tensors involved and for the corresponding responses according to the usual charge, longitudinal and transverse projections, keeping finite the masses of all particles involved. In the case of the hadronic responses, general symmetry principles are invoked to determine which contributions can occur. As a result, the general leptonic-hadronic tensor contraction is given as well as the cross section for the process.

  9. Semi-inclusive charged-current neutrino-nucleus reactions

    DOE PAGES

    Moreno, O.; Donnelly, T. W.; Van Orden, J. W.; ...

    2014-07-17

    The general, universal formalism for semi-inclusive charged-current (anti)neutrino-nucleus reactions is given for studies of any hadronic system, namely, either nuclei or the nucleon itself. The detailed developments are presented with the former in mind and are further specialized to cases where the final-state charged lepton and an ejected nucleon are presumed to be detected. General kinematics for such processes are summarized and then explicit expressions are developed for the leptonic and hadronic tensors involved and for the corresponding responses according to the usual charge, longitudinal and transverse projections, keeping finite the masses of all particles involved. In the case ofmore » the hadronic responses, general symmetry principles are invoked to determine which contributions can occur. As a result, the general leptonic-hadronic tensor contraction is given as well as the cross section for the process.« less

  10. A New Flexible Dependence Measure for Semi-competing Risks

    PubMed Central

    Yang, Jing

    2016-01-01

    Summary Semi-competing risks data are often encountered in chronic disease follow-up studies that record both nonterminal events (eg. disease landmark events) and terminal events (eg. death). Studying the relationship between the nonterminal event and the terminal event can provide insightful information on disease progression. In this paper, we propose a new sensible dependence measure tailored to addressing such an interest. We develop a nonparametric estimator, which is general enough to handle both independent right censoring and left truncation. Our strategy of connecting the new dependence measure with quantile regression enables a natural extension to adjust for covariates with minor additional assumptions imposed. We establish the asymptotic properties of the proposed estimators and develop inferences accordingly. Simulation studies suggest good finite-sample performance of the proposed methods. Our proposals are illustrated via an application to Denmark diabetes registry data. PMID:26916804

  11. Variation in semi-arid soil seed banks

    SciTech Connect

    Boudell-Flanary, J.A.; Link, S.O. |

    1995-09-01

    Seeds recovered from soils in the semi-arid shrub-steppe were compared to test for differences between the seed banks found beneath and cryptogamic crust and the crevices in the crust. Seed quantity found within the crevices was 56% higher than that under the cryptogamic crust. Pseudoroegneria spicata, Poa sandbergii, Bromus tectorum, and Artemisia tridentata are the common species found at the research site. Seeds of Bromus tectorum, Erigeron spp., and Poa spp. were found in the crevices of the crust. Seeds of Artemisia tridentata were not found in the seed banks of either the cryptogamic crust or the crevices in the crust. The higher amount of seeds found in the crevices of the cryptogamic crust suggests that the crevices play a significant role in determining the distributional pattern of shrub-steppe vegetation.

  12. A semi-classical treatment of channeling radiation reaction

    NASA Astrophysics Data System (ADS)

    Huang, Zhirong; Chen, Pisin; Ruth, Ronald D.

    1996-10-01

    A semi-classical formalism is used to calculate the radiation reaction of a relativistic particle in a straight, continuous focusing system. Due to the absence of quantum excitation in such a focusing system, the radiation damping rate of the transverse action obtained using this formalism agrees exactly with the result from the classical Lorentz-Dirac radiation reaction equation. In the limit where the pitch angle of the particle is much smaller than the radiation opening angle, the transverse action damps exponentially with an energy-independent rate that is much faster than the energy decay rate. In the opposite limit, both the transverse action and the energy damp with power laws and their relative rates are comparable. The general time-dependence of the transverse action damping and the energy decay are obtained analytically from these rate equations.

  13. Two-dimensional semi-parametric alignment of chromatograms.

    PubMed

    de Boer, Wim P H; Lankelma, Jan

    2014-06-06

    We present a comprehensive alignment algorithm that extends the semi-parametric approach to two dimensions. The algorithm is based on modeling shifts with a two-dimensional "warp function" such that the sample chromatogram - its shifts corrected with the warp function - is adjusted to the reference chromatogram by minimizing the squared intensity difference. A warp function approach has the advantage that overlapping peaks are easily dealt with compared to other proposed two-dimensional algorithms. Another advantage is that missing peaks are allowed if the absence of these peaks has little numerical effect on the warp function computation and if these peaks occur between existing peaks. Performance of the algorithm is demonstrated using GC×GC data from three batches of three diesel oil samples and LC-MS data from a mouse breast cancer data set.

  14. Quantum dynamics of a semi-infinite homogeneous harmonic chain

    NASA Astrophysics Data System (ADS)

    Prato, Domingo; Lamberti, Pedro W.

    1993-07-01

    The quantum dynamics of a semi-infinite homogeneous harmonic chain is studied. Assuming the system to be in its ground state, a harmonic motion, A sin(ω t), is imposed on the mass at the beginning of the chain. The quantum state of the system for t>0 is calculated by means of the evolution operator. Two different regimes occur: one for angular frequencies ω outside the allowed band ω>ω 0 and the other one for ω inside the band. After a transient the time derivative of the total energy of the chain vanishes for the first regime and tends to a constant for the second one. The mean values of the displacements from their equilibrium position are also calculated for masses along the chain. These averaged displacements and the time derivative of the total energy are shown to give exactly the same expression as in the classical case.

  15. Commercial aspects of semi-reusable launch systems

    NASA Astrophysics Data System (ADS)

    Obersteiner, M. H.; Müller, H.; Spies, H.

    2003-07-01

    This paper presents a business planning model for a commercial space launch system. The financing model is based on market analyses and projections combined with market capture models. An operations model is used to derive the annual cash income. Parametric cost modeling, development and production schedules are used for quantifying the annual expenditures, the internal rate of return, break even point of positive cash flow and the respective prices per launch. Alternative consortia structures, cash flow methods, capture rates and launch prices are used to examine the sensitivity of the model. Then the model is applied for a promising semi-reusable launcher concept, showing the general achievability of the commercial approach and the necessary pre-conditions.

  16. Semi-analytic algorithms for the electrohydrodynamic flow equation

    NASA Astrophysics Data System (ADS)

    Pandey, Ram K.; Baranwal, Vipul K.; Singh, Chandra S.; Singh, Om P.

    2012-12-01

    In this paper, we consider the nonlinear boundary value problem for the electrohydrodynamic (EHD) flow of a fluid in an ion-drag configuration in a circular cylindrical conduit. This phenomenon is governed by a nonlinear second-order differential equation. The degree of nonlinearity is determined by a nondimensional parameter α. We present two semi-analytic algorithms to solve the EHD flow equation for various values of relevant parameters based on optimal homotopy asymptotic method (OHAM) and optimal homotopy analysis method. In 1999, Paullet has shown that for large α, the solutions are qualitatively different from those calculated by Mckee in 1997. Both of our solutions obtained by OHAM and optimal homotopy analysis method are qualitatively similar with Paullet's solutions.

  17. Semi-infinite photocarrier radiometric model for the characterization of semiconductor wafer

    NASA Astrophysics Data System (ADS)

    Liu, Xianming; Li, Bincheng; Huang, Qiuping

    2010-03-01

    The analytical expression is derived to describe the photocarrier radiometric (PCR) signal for a semi-infinite semiconductor wafer excited by a square-wave modulated laser. For comparative study, the PCR signals are calculated by the semi-infinite model and the finite thickness model with several thicknesses. The fitted errors of the electronic transport properties by semi-infinite model are analyzed. From these results it is evident that for thick samples or at high modulation frequency, the semiconductor can be considered as semi-infinite.

  18. Freeze-Drying Makes Improved IPN And Semi-IPN Polymers

    NASA Technical Reports Server (NTRS)

    Pater, Ruth H.; Smith, Ricky E.; Razon, Ruperto T.; Hansen, Marion G.; Hsiung, Hahn J.; Soucek, Mark D.

    1993-01-01

    Novel process developed for production of interpenetrating polymer networks (IPN's) or semi-IPN's with greater fracture toughness and resistance to microcracks. Process controls degree of phase separation in IPN's. In experiment, IPN's and semi-IPN's formed by dissolving constituents in another common solvent in traditional method. Resins and composite materials produced were tested for both traditional and freeze-drying processes. Glass-transition temperatures and data from dynamic mechanical tests of freeze-dried IPN's and semi-IPN's demonstrated freeze-drying process provided much improved IPN's and semi-IPN's.

  19. Semi Impervious Subsurface Barrier for Water Conservation in Lateritic Formations

    NASA Astrophysics Data System (ADS)

    Udayakumar, G.; Mayya, S. G.

    2014-09-01

    The coastal districts of Karnataka in west coast of India experience acute shortage of drinking water during dry season in spite of heavy monsoon rains. Though sufficient recharge of ground water takes place, depletion of water table is very quick, once the rain recedes. It is mainly attributed to the presence of porous and highly permeable laterites and lateritic soils. The hydraulic conductivity of these soils varies in the range of 10-4 to 10-5 cm/s. The conventional water harvesting methods fail to solve the problem. It is necessary to explore innovative method to regulate the lateral subsurface flow and maintain a high water table over a prolonged period of time. The present work is an attempt to explore the possibility of using semi impervious Subsurface Barrier (SSB) to regulate and control the lateral flow of water in the unconfined aquifer in lateritic formations. Appropriate barrier material is arrived at using the locally available soil and the required properties are established. A SSB is built in a suitable location in an identified microwatershed using lateritic soil and the composite soil prepared by mixing requisite percentage of lateritic soil and clay. The hydraulic conductivity of these soils is maintained in the range of 10-6 to 10-7 cm/s so as to behave as semi impervious. The performance analysis is carried out by observing water levels in selected open observation wells before and after the construction of the barrier. The results have shown the successful performance of SSB in maintaining a high water table over a prolonged period of time during summer months, both in u/s and d/s of the barrier.

  20. A novel semi-quantitative method for measuring tissue bleeding.

    PubMed

    Vukcevic, G; Volarevic, V; Raicevic, S; Tanaskovic, I; Milicic, B; Vulovic, T; Arsenijevic, S

    2014-03-01

    In this study, we describe a new semi-quantitative method for measuring the extent of bleeding in pathohistological tissue samples. To test our novel method, we recruited 120 female patients in their first trimester of pregnancy and divided them into three groups of 40. Group I was the control group, in which no dilation was applied. Group II was an experimental group, in which dilation was performed using classical mechanical dilators. Group III was also an experimental group, in which dilation was performed using a hydraulic dilator. Tissue samples were taken from the patients' cervical canals using a Novak's probe via energetic single-step curettage prior to any dilation in Group I and after dilation in Groups II and III. After the tissue samples were prepared, light microscopy was used to obtain microphotographs at 100x magnification. The surfaces affected by bleeding were measured in the microphotographs using the Autodesk AutoCAD 2009 program and its "polylines" function. The lines were used to mark the area around the entire sample (marked A) and to create "polyline" areas around each bleeding area on the sample (marked B). The percentage of the total area affected by bleeding was calculated using the formula: N = Bt x 100 / At where N is the percentage (%) of the tissue sample surface affected by bleeding, At (A total) is the sum of the surfaces of all of the tissue samples and Bt (B total) is the sum of all the surfaces affected by bleeding in all of the tissue samples. This novel semi-quantitative method utilizes the Autodesk AutoCAD 2009 program, which is simple to use and widely available, thereby offering a new, objective and precise approach to estimate the extent of bleeding in tissue samples.

  1. Analyzing Gensini Score as a Semi-Continuous Outcome.

    PubMed

    Kashani, Homa; Zeraati, Hojjat; Mohammad, Kazem; Goodarzynejad, Hamidreza; Mahmoudi, Mahmood; Sadeghian, Saeed; Boroumand, Mohammadali

    2016-04-13

    Background: Investigators frequently encounter continuous outcomes with plenty of values clumped at zero called semi-continuous outcomes. The Gensini score, one of the most widely used scoring systems for expressing coronary angiographic results, is of this type. The aim of this study was to apply two statistical approaches based on the categorization and original scale of the Gensini score to simultaneously assess the association between covariates and the presence and severity of coronary artery disease (CAD). Methods: We considered the data on 1594 individuals admitted to Tehran Heart Center with CAD symptoms from July 2004 to February 2008. The participants' baseline demographic and clinical characteristics were collected, and their coronary angiographic results were expressed through the Gensini score. The generalized ordinal threshold and two-part models were applied for the statistical analyses. Results: Totally, 320 (20.1%) individuals had a Gensini score of zero. The results of neither the two-part model nor the generalized ordinal threshold model showed a significant association between Factor V Leiden and the occurrence of CAD. However, based on the two-part model, Factor V Leiden was associated with the severity of CAD, such that the Gensini score increased by moving from a wild genotype to a heterozygote (β = 0.44; 95% CI: 0.20-0.69 in logarithm scale) or a homozygote mutant (β = 0.70; 95% CI: 0.28- 1.12 in logarithm scale). The proportional odds assumption was not met in our data ([Formula: see text]= 54.26; p value < 0.001); however, a trend toward severe CAD was also observed at each category of the Gensini score using the generalized ordinal threshold model. Conclusion: We conclude that besides loss of information by sorting a semi-continuous outcome, violation from the proportional odds assumption complicates the final decision, especially for clinicians. Therefore, more straightforward models such as the two-part model should receive more

  2. Semi-automatic parcellation of the corpus striatum

    NASA Astrophysics Data System (ADS)

    Al-Hakim, Ramsey; Nain, Delphine; Levitt, James; Shenton, Martha; Tannenbaum, Allen

    2007-03-01

    The striatum is the input component of the basal ganglia from the cerebral cortex. It includes the caudate, putamen, and nucleus accumbens. Thus, the striatum is an important component in limbic frontal-subcortical circuitry and is believed to be relevant both for reward-guided behaviors and for the expression of psychosis. The dorsal striatum is composed of the caudate and putamen, both of which are further subdivided into pre- and post-commissural components. The ventral striatum (VS) is primarily composed of the nucleus accumbens. The striatum can be functionally divided into three broad regions: 1) a limbic; 2) a cognitive and 3) a sensor-motor region. The approximate corresponding anatomic subregions for these 3 functional regions are: 1) the VS; 2) the pre/post-commissural caudate and the pre-commissural putamen and 3) the post-commissural putamen. We believe assessing these subregions, separately, in disorders with limbic and cognitive impairment such as schizophrenia may yield more informative group differences in comparison with normal controls than prior parcellation strategies of the striatum such as assessing the caudate and putamen. The manual parcellation of the striatum into these subregions is currently defined using certain landmark points and geometric rules. Since identification of these areas is important to clinical research, a reliable and fast parcellation technique is required. Currently, only full manual parcellation using editing software is available; however, this technique is extremely time intensive. Previous work has shown successful application of heuristic rules into a semi-automatic platform1. We present here a semi-automatic algorithm which implements the rules currently used for manual parcellation of the striatum, but requires minimal user input and significantly reduces the time required for parcellation.

  3. Micro ultrasonic powder molding for semi-crystalline polymers

    NASA Astrophysics Data System (ADS)

    Liang, Xiong; Wu, Xiaoyu; Zeng, Kun; Xu, Bin; Wu, Shiyun; Zhao, Hang; Li, Bing; Ruan, Shuangchen

    2014-04-01

    The present paper introduces micro ultrasonic powder molding (micro-UPM), a novel method for forming micro semi-crystalline polymer parts. In the proposed method, semi-crystalline polymer powder is rapidly heated and plasticized by ultrasonic vibration, after which the microcavity is filled with the melt under sonotrode pressure (PU) to form a variety of micro polymer parts. Differential scanning calorimetry, scanning electron microscopy, and nanoindentation tests demonstrate that micro-UPM UHMWPE (ultra-high molecular weight polyethylene) parts consists of nascent and melt-recrystallized phases and that energy concentrated at particle interfaces as a result of high-frequency friction, compressive deformation, and ultrasonic radiation leads to rapid diffusion and interpenetration of the chain segment. The particle interface melts result in strong co-crystallization during cooling. To investigate the effect of ultrasonic duration time (TU) on the quality of micro-UPM UHMWPE parts, different TU values are utilized to form UHMWPE parts at a PU of 16 MPa and a holding time of 5.0 s. As TU increases, the number and sizes of interparticle voids gradually decrease. A rise in the melting peak of the melt-recrystallized phase and a drop in the melting peak of the nascent phrase as well as crystallinity are further observed. When TU is only 1.5 s, the crystallinity of the micro plastic part reaches a minimum value of 54.3% and the melt-recrystallized phase fraction reaches a maximum value of 98.3%. Powder particle interfaces almost disappear in this case, and optimum quality of the micro-UPM UHMWPE part is achieved.

  4. Observer performance in semi-automated microbleed detection

    NASA Astrophysics Data System (ADS)

    Kuijf, Hugo J.; Brundel, Manon; de Bresser, Jeroen; Viergever, Max A.; Biessels, Geert Jan; Geerlings, Mirjam I.; Vincken, Koen L.

    2013-03-01

    Cerebral microbleeds are small bleedings in the human brain, detectable with MRI. Microbleeds are associated with vascular disease and dementia. The number of studies involving microbleed detection is increasing rapidly. Visual rating is the current standard for detection, but is a time-consuming process, especially at high-resolution 7.0 T MR images, has limited reproducibility and is highly observer dependent. Recently, multiple techniques have been published for the semi-automated detection of microbleeds, attempting to overcome these problems. In the present study, a 7.0 T dual-echo gradient echo MR image was acquired in 18 participants with microbleeds from the SMART study. Two experienced observers identified 54 microbleeds in these participants, using a validated visual rating scale. The radial symmetry transform (RST) can be used for semi-automated detection of microbleeds in 7.0 T MR images. In the present study, the results of the RST were assessed by two observers and 47 microbleeds were identified: 35 true positives and 12 extra positives (microbleeds that were missed during visual rating). Hence, after scoring a total number of 66 microbleeds could be identified in the 18 participants. The use of the RST increased the average sensitivity of observers from 59% to 69%. More importantly, inter-observer agreement (ICC and Dice's coefficient) increased from 0.85 and 0.64 to 0.98 and 0.96, respectively. Furthermore, the required rating time was reduced from 30 to 2 minutes per participant. By fine-tuning the RST, sensitivities up to 90% can be achieved, at the cost of extra false positives.

  5. Terrestrial ecology of semi-aquatic giant gartersnakes (Thamnophis gigas)

    USGS Publications Warehouse

    Halstead, Brian J.; Skalos, Shannon M.; Wylie, Glenn D.; Casazza, Michael L.

    2015-01-01

    Wetlands are a vital component of habitat for semiaquatic herpetofauna, but for most species adjacent terrestrial habitats are also essential. We examined the use of terrestrial environments by Giant Gartersnakes (Thamnophis gigas) to provide behavioral information relevant to conservation of this state and federally listed threatened species. We used radio telemetry data collected 1995–2011 from adults at several sites throughout the Sacramento Valley, California, USA, to examine Giant Gartersnake use of the terrestrial environment. We found Giant Gartersnakes in terrestrial environments more than half the time during the summer, with the use of terrestrial habitats increasing to nearly 100% during brumation. While in terrestrial habitats, we found Giant Gartersnakes underground more than half the time in the early afternoon during summer, and the probability of being underground increased to nearly 100% of the time at all hours during brumation. Extreme temperatures also increased the probability that we would find Giant Gartersnakes underground. Under most conditions, we found Giant Gartersnakes to be within 10 m of water at 95% of observations. For females during brumation and individuals that we found underground, however, the average individual had a 10% probability of being located > 20 m from water. Individual variation in each of the response variables was extensive; therefore, predicting the behavior of an individual was fraught with uncertainty. Nonetheless, our estimates provide resource managers with valuable information about the importance of protecting and carefully managing terrestrial habitats for conserving a rare semiaquatic snake.

  6. Effect of Danshen aqueous extract on serum hs-CRP, IL-8, IL-10, TNF-α levels, and IL-10 mRNA, TNF-α mRNA expression levels, cerebral TGF-β1 positive expression level and its neuroprotective mechanisms in CIR rats.

    PubMed

    Liang, Xue-Yun; Li, Hai-Ning; Yang, Xiao-Yan; Zhou, Wen-Yan; Niu, Jian-Guo; Chen, Ben-Dong

    2013-04-01

    To observe the effects of Danshen aqueous extract (DSAE) on the cerebral tissue and nerve stem cells in cerebral ischemia reperfusion (CIR) rats. The model rats were prepared by occlusion of the middle cerebral artery for 2 h and then by reperfusion. They were randomly divided into five groups: a control group, an CIR group and three DSAE-treated groups. As compared with the sham control group, there was significant increase (P < 0.05, P < 0.01) in the serum high-sensitivity C-reactive protein (hs-CRP) and interleukin-8 (IL-8) levels, interleukin-10 (IL-10), tumor necrosis factor-alpha (TNF-α) levels, and IL-10 mRNA, TNF-α mRNA expression levels, function score, Infarct size, TUNEL + cell counts, cerebral transforming growth factor beta 1 (TGF-β1) positive expression and cerebral neuron specific enolase (NSE) levels, and decrease in fas-associated protein with death domain (FADD) and death-associated protein (Daxx) positive expression levels in the CIR group. Compared with CIR group, DSAE treatment dose-dependently significantly decreased serum hs-CRP, IL-8, IL-10, TNF-α levels, and IL-10 mRNA, TNF-α mRNA expression levels, function score, Infarct size, TUNEL + cell counts, cerebral TGF-β1 positive expression and cerebral NSE levels, and increase FADD and Daxx positive expression levels in the CIR + DSAE groups. Taken together, these results suggest that DSAE has a neuroprotective role in the CIR rats, which may be related to improvement of immunity function, proteins and genes expression.

  7. A Nonlinear Multigrid Solver for an Atmospheric General Circulation Model Based on Semi-Implicit Semi-Lagrangian Advection of Potential Vorticity

    NASA Technical Reports Server (NTRS)

    McCormick, S.; Ruge, John W.

    1998-01-01

    This work represents a part of a project to develop an atmospheric general circulation model based on the semi-Lagrangian advection of potential vorticity (PC) with divergence as the companion prognostic variable.

  8. Indexed semi-Markov process for wind speed modeling.

    NASA Astrophysics Data System (ADS)

    Petroni, F.; D'Amico, G.; Prattico, F.

    2012-04-01

    -order Markov chain with different number of states, and Weibull distribution. All this model use Markov chains to generate synthetic wind speed time series but the search for a better model is still open. Approaching this issue, we applied new models which are generalization of Markov models. More precisely we applied semi-Markov models to generate synthetic wind speed time series. In a previous work we proposed different semi-Markov models, showing their ability to reproduce the autocorrelation structures of wind speed data. In that paper we showed also that the autocorrelation is higher with respect to the Markov model. Unfortunately this autocorrelation was still too small compared to the empirical one. In order to overcome the problem of low autocorrelation, in this paper we propose an indexed semi-Markov model. More precisely we assume that wind speed is described by a discrete time homogeneous semi-Markov process. We introduce a memory index which takes into account the periods of different wind activities. With this model the statistical characteristics of wind speed are faithfully reproduced. The wind is a very unstable phenomenon characterized by a sequence of lulls and sustained speeds, and a good wind generator must be able to reproduce such sequences. To check the validity of the predictive semi-Markovian model, the persistence of synthetic winds were calculated, then averaged and computed. The model is used to generate synthetic time series for wind speed by means of Monte Carlo simulations and the time lagged autocorrelation is used to compare statistical properties of the proposed models with those of real data and also with a time series generated though a simple Markov chain. [1] A. Shamshad, M.A. Bawadi, W.M.W. Wan Hussin, T.A. Majid, S.A.M. Sanusi, First and second order Markov chain models for synthetic generation of wind speed time series, Energy 30 (2005) 693-708. [2] H. Nfaoui, H. Essiarab, A.A.M. Sayigh, A stochastic Markov chain model for simulating

  9. Problems and Prospects of SWAT Model Application on an Arid/Semi-Arid Watershed in Arizona

    EPA Science Inventory

    In arid/semi-arid regions, precipitation mainly occurs during two periods: long-duration, low-intensity rainfall in winter; and short-duration, high-intensity rainfall in summer. Watersheds in arid/semi-arid regions often release water almost immediately after a storm due to spa...

  10. 33 CFR 149.410 - Where must portable and semi-portable fire extinguishers be located?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...-portable fire extinguishers be located? 149.410 Section 149.410 Navigation and Navigable Waters COAST GUARD... and semi-portable fire extinguishers be located? All portable and semi-portable fire extinguishers described in table 149.409 must be located in the open so as to be readily seen....

  11. 33 CFR 149.410 - Where must portable and semi-portable fire extinguishers be located?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...-portable fire extinguishers be located? 149.410 Section 149.410 Navigation and Navigable Waters COAST GUARD... and semi-portable fire extinguishers be located? All portable and semi-portable fire extinguishers described in table 149.409 must be located in the open so as to be readily seen....

  12. Scaffolded Semi-Flipped General Chemistry Designed to Support Rural Students' Learning

    ERIC Educational Resources Information Center

    Lenczewski, Mary S.

    2016-01-01

    Students who lack academic maturity can sometimes feel overwhelmed in a fully flipped classroom. Here an alternative, the Semi-Flipped method, is discussed. Rural students, who face unique challenges in transitioning from high school learning to college-level learning, can particularly profit from the use of the Semi-Flipped method in the General…

  13. 33 CFR 147.843 - Thunder Horse Semi-Submersible safety zone.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 33 Navigation and Navigable Waters 2 2012-07-01 2012-07-01 false Thunder Horse Semi-Submersible safety zone. 147.843 Section 147.843 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND...-Submersible safety zone. (a) Description. Thunder Horse Semi-Submersible, Mississippi Canyon 778 (MC...

  14. 33 CFR 147.843 - Thunder Horse Semi-Submersible safety zone.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 33 Navigation and Navigable Waters 2 2014-07-01 2014-07-01 false Thunder Horse Semi-Submersible safety zone. 147.843 Section 147.843 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND...-Submersible safety zone. (a) Description. Thunder Horse Semi-Submersible, Mississippi Canyon 778 (MC...

  15. 33 CFR 147.843 - Thunder Horse Semi-Submersible safety zone.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 33 Navigation and Navigable Waters 2 2013-07-01 2013-07-01 false Thunder Horse Semi-Submersible safety zone. 147.843 Section 147.843 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND...-Submersible safety zone. (a) Description. Thunder Horse Semi-Submersible, Mississippi Canyon 778 (MC...

  16. 33 CFR 147.843 - Thunder Horse Semi-Submersible safety zone.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Thunder Horse Semi-Submersible safety zone. 147.843 Section 147.843 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND...-Submersible safety zone. (a) Description. Thunder Horse Semi-Submersible, Mississippi Canyon 778 (MC...

  17. Interaction of ice floes with columns of a semi-submersible platform

    SciTech Connect

    Noble, P.G.; Singh, D.

    1983-12-01

    A preliminary research project has been carried out to determine the effect of small ice floes on a semi-submersible drilling unit. Physical model tests have been conducted with two main objectives: first, to determine the ability of the columns to prevent ice from passing between them (arching) and thus minimizing the chance of riser damage, and second, to determine the total ice load on the semi-submersible during interaction with ice field concentrations. Three models were used, representing one half of a four, six or eight-legged semi-submersible platform. The dimensions and spacing of the columns were such that the heave and pitch responses were kept constant. The tests were conducted at a model scale of 1:30 using synthetic ice. Test results showed the maximum load measured on a four-legged semisubmersible model, at 100 percent ice floe concentration, was on the order of half of that measured on six or eight-legged semi-submersible models. Also the ice loads on a four-legged semi-submersible model at lower ice floe concentration were substantially less than those for six or eight-legged semi-submersible models. The total ice load on semi-submersible models is found to be a function of ice floe concentration. Up to about 75 percent ice concentration, ice loads varied linearly. Beyond that, the loads increased exponentially for all semi-submersible models.

  18. 33 CFR 147.843 - Thunder Horse Semi-Submersible safety zone.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Thunder Horse Semi-Submersible safety zone. 147.843 Section 147.843 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND...-Submersible safety zone. (a) Description. Thunder Horse Semi-Submersible, Mississippi Canyon 778 (MC...

  19. Semi-transparent polymer solar cells with excellent sub-bandgap transmission for third generation photovoltaics.

    PubMed

    Beiley, Zach M; Christoforo, M Greyson; Gratia, Paul; Bowring, Andrea R; Eberspacher, Petra; Margulis, George Y; Cabanetos, Clément; Beaujuge, Pierre M; Salleo, Alberto; McGehee, Michael D

    2013-12-23

    Semi-transparent organic photovoltaics are of interest for a variety of photovoltaic applications, including solar windows and hybrid tandem photovoltaics. The figure shows a photograph of our semi-transparent solar cell, which has a power conversion efficiency of 5.0%, with an above bandgap transmission of 34% and a sub-bandgap transmission of 81%.

  20. Sputtered pin amorphous silicon semi-conductor device and method therefor

    DOEpatents

    Moustakas, Theodore D.; Friedman, Robert A.

    1983-11-22

    A high efficiency amorphous silicon PIN semi-conductor device is constructed by the sequential sputtering of N, I and P layers of amorphous silicon and at least one semi-transparent ohmic electrode. A method of construction produces a PIN device, exhibiting enhanced physical integrity and facilitates ease of construction in a singular vacuum system and vacuum pump down procedure.

  1. 78 FR 49289 - Agency Information Collection Activities; Extension of a Currently Approved Collection: Semi...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-13

    ... Progress Report for the Technical Assistance Program ACTION: 60-Day notice. The Department of Justice... approved collection. (2) Title of the Form/Collection: Semi-annual Progress Report for the Technical... (Technical Assistance providers) approximately one hour to complete a semi-annual progress report twice...

  2. Test/QA Plan (TQAP) for Verification of Semi-Continuous Ambient Air Monitoring Systems

    EPA Science Inventory

    The purpose of the semi-continuous ambient air monitoring technology (or MARGA) test and quality assurance plan is to specify procedures for a verification test applicable to commercial semi-continuous ambient air monitoring technologies. The purpose of the verification test is ...

  3. On Generalized Continuous D Semi-Classical Hermite and Chebychev Orthogonal Polynomials of Class One

    NASA Astrophysics Data System (ADS)

    Azatassou, E.; Hounkonnou, M. N.

    2002-10-01

    In this contribution, starting from the system of equations for recurrence coefficients generated by continuous D semi-classical Laguerre-Freud equations of class 1, we deduce the β constant recurrence relation coefficient γn leading to the generalized D semi-classical Hermite and Chebychev orthogonal polynomials of class 1. Various interesting cases are pointed out.

  4. CLOSURE BETWEEN SEMI-CONTINUOUS MEASUREMENT OF PM 2.5 MASS AND COMPOSITION

    EPA Science Inventory

    This extended abstract reports the first successful attempt to quantitatively measure all the major species of PM2.5 on a semi-continuous basis. Comparisons are made between both PC-BOSS integrated species concentration measurements with semi-continuous species measur...

  5. Combined Dynamic Arrays for Storing and Searching Semi-Ordered Tandem Mass Spectrometry Data

    Technology Transfer Automated Retrieval System (TEKTRAN)

    When performing bioinformatics analysis on tandem mass spectrometry data, there is a computational need to efficiently store and sort these semi-ordered data sets. To solve this problem, a new data structure based on dynamic arrays was designed and implemented in an algorithm that parses semi-order...

  6. 21 CFR 888.3350 - Hip joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Hip joint metal/polymer semi-constrained cemented prosthesis. 888.3350 Section 888.3350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND... metal/polymer semi-constrained cemented prosthesis. (a) Identification. A hip joint metal/polymer...

  7. 21 CFR 888.3350 - Hip joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Hip joint metal/polymer semi-constrained cemented prosthesis. 888.3350 Section 888.3350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND... metal/polymer semi-constrained cemented prosthesis. (a) Identification. A hip joint metal/polymer...

  8. 21 CFR 888.3350 - Hip joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Hip joint metal/polymer semi-constrained cemented prosthesis. 888.3350 Section 888.3350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND... metal/polymer semi-constrained cemented prosthesis. (a) Identification. A hip joint metal/polymer...

  9. 21 CFR 888.3350 - Hip joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Hip joint metal/polymer semi-constrained cemented prosthesis. 888.3350 Section 888.3350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND... metal/polymer semi-constrained cemented prosthesis. (a) Identification. A hip joint metal/polymer...

  10. 21 CFR 888.3350 - Hip joint metal/polymer semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Hip joint metal/polymer semi-constrained cemented prosthesis. 888.3350 Section 888.3350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND... metal/polymer semi-constrained cemented prosthesis. (a) Identification. A hip joint metal/polymer...

  11. Stress distribution in a semi-infinite body symmetrically loaded over a circular area

    NASA Technical Reports Server (NTRS)

    Mcginness, H.

    1980-01-01

    Algorithms are developed for computing stresses in a semi-infinite body when loaded by a uniform pressure acting over a circular area. The algorithm allows easy determination of any stress component in a semi-infinite body having a known Poisson's ratio. Example curves are plotted for Portland cement grout and metal representative values.

  12. ESTIMATING TRANSPORT AND DEPOSITION OF A SEMI-VOLATILE COMPOUND WITH A REGIONAL PHOTOCHEMICAL MODEL

    EPA Science Inventory

    To simulate the fate of compounds that are considered semi-volatile and toxic, we have modified a model for regional particulate matter. Our changes introduce a semi-volatile compound into the atmosphere as gaseous emissions from an area source. Once emitted, the gas can transf...

  13. 21 CFR 888.3340 - Hip joint metal/composite semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Hip joint metal/composite semi-constrained cemented prosthesis. 888.3340 Section 888.3340 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF... Hip joint metal/composite semi-constrained cemented prosthesis. (a) Identification. A hip joint...

  14. 21 CFR 888.3340 - Hip joint metal/composite semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Hip joint metal/composite semi-constrained... Hip joint metal/composite semi-constrained cemented prosthesis. (a) Identification. A hip joint metal... hip joint. The device limits translation and rotation in one or more planes via the geometry of...

  15. 21 CFR 888.3340 - Hip joint metal/composite semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Hip joint metal/composite semi-constrained... Hip joint metal/composite semi-constrained cemented prosthesis. (a) Identification. A hip joint metal... hip joint. The device limits translation and rotation in one or more planes via the geometry of...

  16. 21 CFR 888.3340 - Hip joint metal/composite semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Hip joint metal/composite semi-constrained... Hip joint metal/composite semi-constrained cemented prosthesis. (a) Identification. A hip joint metal... hip joint. The device limits translation and rotation in one or more planes via the geometry of...

  17. 21 CFR 888.3340 - Hip joint metal/composite semi-constrained cemented prosthesis.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Hip joint metal/composite semi-constrained... Hip joint metal/composite semi-constrained cemented prosthesis. (a) Identification. A hip joint metal... hip joint. The device limits translation and rotation in one or more planes via the geometry of...

  18. Dispositifs semi-conducteurs pour biodetection photonique et imagerie hyperspectrale

    NASA Astrophysics Data System (ADS)

    Lepage, Dominic

    La creation d'un microsysteme d'analyse biochimique, capable de livrer des diagnostics preliminaires sur la quantification d'elements pathogenes, est un defi multidisciplinaire ayant un impact potentiel important sur la majorite des activites humaines en sante et securite. En effet, un dispositif integre, peu dispendieux et livrant des resultats facilement interpretables, permettrait une vulgarisation des capacites de biodetection a travers differents domaines d'applications societaires et industriels. Le present document se concentre sur l'integration monolithique d'une methode de biocaracterisation dans le but de generer un transducteur miniaturise et efficace, element central d'un microsysteme de detection. Le projet de recherche ici presente vise l'etude de l'applicabilite d'un capteur plasmonique integre par l'entremise de nanostructures semi-conductrices aux proprietes quantiques et luminescentes. L'approche presentee est globale; c'est-a-dire qu'on vise a repondre aux questions fondamentales impliquant la comprehension des phenomenes photoniques, le developpement et la fabrication des dispositifs, les methodes de caracterisations possibles ainsi que l'application d'un transducteur SPR integre a la biodetection. En d'autres termes : dans quelles circonstances et comment un transducteur plasmonique integre doit-il etre realise pour l'application a la detection delocalisee d'elements pathogenes? Dans le but d'engendrer un instrument simple a l'echelle de l'usager, l'integration de la connaissance a l'echelle du design est donc effectuee. Ainsi, des capteurs plasmoniques monolithiques sont concus a l'aide de modeles theoriques ici presentes. Un instrument de mesure hyperspectrale conjuguee permettant de cartographier directement la relation de dispersion des plasmons diffractes a ete construit et teste. Cet instrument est employe a la cartographie d'elements de diffusion. Finalement, une demonstration du fonctionnement du dispositif, appliquee a la

  19. Semi-brittle flow of granitoid fault rocks in experiments

    NASA Astrophysics Data System (ADS)

    Pec, Matej; Stünitz, Holger; Heilbronner, Renée.; Drury, Martyn

    2016-03-01

    Field studies and seismic data show that semi-brittle flow of fault rocks probably is the dominant deformation mechanism at the base of the seismogenic zone at the so-called frictional-viscous transition. To understand the physical and chemical processes accommodating semi-brittle flow, we have performed an experimental study on synthetic granitoid fault rocks exploring a broad parameter space (temperature, T = 300, 400, 500, and 600°C, confining pressure, Pc ≈ 300, 500, 1000, and 1500 MPa, shear strain rate, γṡ ≈ 10-3, 10-4, 10-5, and 10-6 s-1, to finite shear strains, γ = 0-5). The experiments have been carried out using a granular material with grain size smaller than 200 µm with a little H2O added (0.2 wt %). Only two experiments (performed at the fastest strain rates and lowest temperatures) have failed abruptly right after reaching peak strength (τ ~ 1400 MPa). All other samples reach high shear stresses (τ ~ 570-1600 MPa) then weaken slightly (by Δτ ~ 10-190 MPa) and continue to deform at a more or less steady state stress level. Clear temperature dependence and a weak strain rate dependence of the peak as well as steady state stress levels are observed. In order to express this relationship, the strain rate-stress sensitivity has been fit with a stress exponent, assuming γ˙ ∝ τn and yields high stress exponents (n ≈ 10-140), which decrease with increasing temperature. The microstructures show widespread comminution, strain partitioning, and localization into slip zones. The slip zones contain at first nanocrystalline and partly amorphous material. Later, during continued deformation, fully amorphous material develops in some of the slip zones. Despite the mechanical steady state conditions, the fabrics in the slip zones and outside continue to evolve and do not reach a steady state microstructure below γ = 5. Within the slip zones, the fault rock material progressively transforms from a crystalline solid to an amorphous material. We

  20. Semi-empirical model of Traveling Ionospheric Disturbances

    NASA Astrophysics Data System (ADS)

    Tyrnov, Oleg; Fedorenko, Yury; Dorohov, Vasiliy; Fedorenko, Vladimir

    2014-05-01

    A multiscale semi-empirical model of traveling ionospheric disturbances (TIDs) is developed. Large and medium scale TIDs are different stages of an initial perturbation generated by the same source. The model is based on the following assumptions: (1) TIDs are generated by acoustic gravity waves (AGWs) and propagate as pressure waves; (2) time intervals between adjacent extrema of atmospheric pressure oscillations in a disturbance source are constant; (3) the pressure extrema propagate from the source up to ~ 14000 km at a constant horizontal velocity; (4) the velocity of each extremum is determined only by its number in a TID train. The model was validated using literature data on disturbances generated by about twenty surface and high altitude nuclear explosions, two volcano explosions, one earthquake and by energetic proton precipitation events in the magnetospheric cusp of the northern hemisphere. Model tests using literature data show that the spatial and temporal TID periods may be predicted with an accuracy of 12%. Adequacy of the model was also confirmed by our observations collected using transionospheric sounding. The following parameters of TIDs: the spatial period, amplitude and front inclination angle in a vertical plain increase with decreasing latitude in almost all observations made during the two solar cycles in the range of latitudes ~ 33 - 66° N. This indicates that the sources of most TIDs of natural origin are located at high-latitudes. The semi-empirical model predicts the sawtooth pieces on time dynamics of spatial TID periods observed in our transionospheric radiosounding experiments. Directly proportional relationship between the amplitude and horizontal spatial period of TIDs was observed during the minimum and maximum of solar activity. Diurnal and seasonal variability of the TID occurrence, defined as ratio of TID events to the total number of observations for the corresponding period, is not observed. However, the TID occurrence was

  1. Turbidity - a Semi-Continuous Monitoring Option for Suspended Solids

    NASA Astrophysics Data System (ADS)

    Lendvay, J. M.; Rosasco, M. V.; David, K. E.

    2012-12-01

    Redwood Creek, a third order coastal stream flowing through Muir Woods National Monument and Golden Gate National Recreation Area in Marin County, California, was once the spawning grounds for a relatively large population of Coho Salmon (Oncorhynchus kisutch). In recent years less than 1% of historic populations have been returning to the stream. Redwood creek is currently undergoing extensive ecological restoration in an attempt to improve the spawning habitat for the salmon. The original stream path has been altered in the past to make way for development and the National Park Service has been working towards restoring much of the stream's natural functionality with the hope that the salmon population will increase. The restoration process has altered the surrounding riparian landscape in the Redwood Creek watershed. Riparian disturbance caused by vegetation and levee removal as a part of the restoration process followed by installation of seedlings raises concern about the concentration of sediments in the water. Throughout 2011-2012 three parameters for water quality were monitored at Redwood Creek. Suspended sediment concentration (SSC) and total suspended solids (TSS) measurements to determine the concentration of suspended particles in the water column at a given point in time. Turbidity, measured in Nephelometric Turbidity Units (NTU) is a measure of the water's cloudiness caused by suspended particles. Turbidity measurements are favored as they provide a semi-automated monitoring option. Therefore, development of a relationship between turbidity and SSC and TSS is desired. Water samples were analyzed for TSS and SSC using the EPA standard methods, and Turbidity was measured using a Hach 2100Q portable turbidimeter. Additional semi-continuous monitoring of turbidity was completed in situ using Hydrolab DS5X datasondes (with self-cleaning turbidity sensor). The relationship between TSS, SSC and turbidity was determined using a linear regression model for

  2. A semi-Dirac point and an electromagnetic topological transition in a dielectric photonic crystal.

    PubMed

    Wu, Ying

    2014-01-27

    Accidental degeneracy in a photonic crystal consisting of a square array of elliptical dielectric cylinders leads to both a semi-Dirac point at the center of the Brillouin zone and an electromagnetic topological transition (ETT). A perturbation method is deduced to affirm the peculiar linear-parabolic dispersion near the semi-Dirac point. An effective medium theory is developed to explain the simultaneous semi-Dirac point and ETT and to show that the photonic crystal is either a zero-refractive-index material or an epsilon-near-zero material at the semi-Dirac point. Drastic changes in the wave manipulation properties at the semi-Dirac point, resulting from ETT, are described.

  3. Semi-active controller design for vibration suppression and energy harvesting via LMI approach

    NASA Astrophysics Data System (ADS)

    Liu, Yilun; Lin, Chi-Chang; Zuo, Lei

    2014-04-01

    The vibration control plays an important role in energy harvesting systems. Compared to the active control, semi-active control is a more preferred alternative for practical use. Many different semi-active control strategies have been developed, among which LQ-clip, Skyhook and model predictive control are the most popular strategies in literatures. In this paper, a different control strategy that designs semi-active controller via LMI approach is proposed. Different from clipping the control input after controller construction like most existing control methods, the proposed method fulfills the semi-active control input feasibility constraints before the controller construction. The methodology is developed through LMI approach which leads to a stabilizing linear controller to ensure semi-active constraint and the pre-designed performance. An illustrative example, vibration control system of a tall building, is presented to show the efficiency of the method and validate the new approach.

  4. Drift-free MPEG-4 AVC semi-fragile watermarking

    NASA Astrophysics Data System (ADS)

    Hasnaoui, M.; Mitrea, M.

    2014-02-01

    While intra frame drifting is a concern for all types of MPEG-4 AVC compressed-domain video processing applications, it has a particular negative impact in watermarking. In order to avoid the drift drawbacks, two classes of solutions are currently considered in the literature. They try either to compensate the drift distortions at the expense of complex decoding/estimation algorithms or to restrict the insertion to the blocks which are not involved in the prediction, thus reducing the data payload. The present study follows a different approach. First, it algebraically models the drift distortion spread problem by considering the analytic expressions of the MPEG-4 AVC encoding operations. Secondly, it solves the underlying algebraic system under drift-free constraints. Finally, the advanced solution is adapted to take into account the watermarking peculiarities. The experiments consider an m-QIM semi-fragile watermarking method and a video surveillance corpus of 80 minutes. For prescribed data payload (100 bit/s), robustness (BER < 0.1 against transcoding at 50% in stream size), fragility (frame modification detection with accuracies of 1/81 from the frame size and 3s) and complexity constraints, the modified insertion results in gains in transparency of 2 dB in PSNR, of 0.4 in AAD, of 0.002 in IF, of 0.03 in SC, of 0.017 NCC and 22 in DVQ.

  5. Security of Semi-Device-Independent Random Number Expansion Protocols.

    PubMed

    Li, Dan-Dan; Wen, Qiao-Yan; Wang, Yu-Kun; Zhou, Yu-Qian; Gao, Fei

    2015-10-27

    Semi-device-independent random number expansion (SDI-RNE) protocols require some truly random numbers to generate fresh ones, with making no assumptions on the internal working of quantum devices except for the dimension of the Hilbert space. The generated randomness is certified by non-classical correlation in the prepare-and-measure test. Until now, the analytical relations between the amount of the generated randomness and the degree of non-classical correlation, which are crucial for evaluating the security of SDI-RNE protocols, are not clear under both the ideal condition and the practical one. In the paper, first, we give the analytical relation between the above two factors under the ideal condition. As well, we derive the analytical relation under the practical conditions, where devices' behavior is not independent and identical in each round and there exists deviation in estimating the non-classical behavior of devices. Furthermore, we choose a different randomness extractor (i.e., two-universal random function) and give the security proof.

  6. Quantum ergodicity breaking in semi-classical electron transfer dynamics.

    PubMed

    Goychuk, Igor

    2017-01-25

    Can the statistical properties of single-electron transfer events be correctly predicted within a common equilibrium ensemble description? This fundamental in nanoworld question of ergodic behavior is scrutinized within a very basic semi-classical curve-crossing problem. It is shown that in the limit of non-adiabatic electron transfer (weak tunneling) well-described by the Marcus-Levich-Dogonadze (MLD) rate the answer is yes. However, in the limit of the so-called solvent-controlled adiabatic electron transfer, a profound breaking of ergodicity occurs. Namely, a common description based on the ensemble reduced density matrix with an initial equilibrium distribution of the reaction coordinate is not able to reproduce the statistics of single-trajectory events in this seemingly classical regime. For sufficiently large activation barriers, the ensemble survival probability in a state remains nearly exponential with the inverse rate given by the sum of the adiabatic curve crossing (Kramers) time and the inverse MLD rate. In contrast, near to the adiabatic regime, the single-electron survival probability is clearly non-exponential, even though it possesses an exponential tail which agrees well with the ensemble description. Initially, it is well described by a Mittag-Leffler distribution with a fractional rate. Paradoxically, the mean transfer time in this classical on the ensemble level regime is well described by the inverse of the nonadiabatic quantum tunneling rate on a single particle level. An analytical theory is developed which perfectly agrees with stochastic simulations and explains our findings.

  7. Machine learning and cosmological simulations - I. Semi-analytical models

    NASA Astrophysics Data System (ADS)

    Kamdar, Harshil M.; Turk, Matthew J.; Brunner, Robert J.

    2016-01-01

    We present a new exploratory framework to model galaxy formation and evolution in a hierarchical Universe by using machine learning (ML). Our motivations are two-fold: (1) presenting a new, promising technique to study galaxy formation, and (2) quantitatively analysing the extent of the influence of dark matter halo properties on galaxies in the backdrop of semi-analytical models (SAMs). We use the influential Millennium Simulation and the corresponding Munich SAM to train and test various sophisticated ML algorithms (k-Nearest Neighbors, decision trees, random forests, and extremely randomized trees). By using only essential dark matter halo physical properties for haloes of M > 1012 M⊙ and a partial merger tree, our model predicts the hot gas mass, cold gas mass, bulge mass, total stellar mass, black hole mass and cooling radius at z = 0 for each central galaxy in a dark matter halo for the Millennium run. Our results provide a unique and powerful phenomenological framework to explore the galaxy-halo connection that is built upon SAMs and demonstrably place ML as a promising and a computationally efficient tool to study small-scale structure formation.

  8. CLASSIC: a semi-distributed rainfall-runoff modelling system

    NASA Astrophysics Data System (ADS)

    Crooks, S. M.; Naden, P. S.

    2007-01-01

    This paper describes the development of a semi-distributed conceptual rainfall runoff model, originally formulated to simulate impacts of climate and land-use change on flood frequency. The model has component modules for soil moisture balance, drainage response and channel routing and is grid-based to allow direct incorporation of GIS- and Digital Terrain Model (DTM)-derived data sets into the initialisation of parameter values. Catchment runoff is derived from the aggregation of components of flow from the drainage module within each grid square and from total routed flow from all grid squares. Calibration is performed sequentially for the three modules using different objective functions for each stage. A key principle of the modelling system is the concept of nested calibration, which ensures that all flows simulated for points within a large catchment are spatially consistent. The modelling system is robust and has been applied successfully at different spatial scales to three large catchments in the UK, including comparison of observed and modelled flood frequency and flow duration curves, simulation of flows for uncalibrated catchments and identification of components of flow within a modelled hydrograph. The role of such a model in integrated catchment studies is outlined.

  9. Life extension of semi-submersible drilling unit

    SciTech Connect

    Hadley, I.; Sinclair, C.I.K.; Magne, E.

    1995-12-31

    This paper describes the life extension of a semi-submersible drilling rig built in the early 1970`s. A nominal design life of 20 years was estimated at the time of building; however, in the interim period, numerous improvements have been made in fatigue life estimation ad life improvement techniques, raising the possibility that a further 20 years of operation could be considered. The life extension strategy made use of a number of aspects of offshore technology which were not available at the time of construction of the rig. Finite element studies and results from offshore research programs were used to gauge the effect of fatigue life improvement techniques. The program demonstrated the feasibility of extending the operation of the rig for a further 20 years, with the interval between in-service inspection increased to every five years. It also provided a valuable database of fracture toughness data for the rig materials, which may be used in future work to address reliability issues.

  10. A semi-Markov reliability analysis of alternating systems

    SciTech Connect

    Lee, Kwang Nam; Cho, Nam Zin

    1989-01-01

    Current nuclear power plants must be highly reliable with respect to safety and economy. Consequently, development of a new safety evaluation methodology is desired for the accurate evaluation of safety and economy. A nuclear power plant consists of many systems. This paper is concerned with the reliability evaluation of alternating systems. An alternating system usually consists of multitrains, and its operation alternates from one train to another. Examples of these are the nuclear service cooling water system, the component cooling water system, and the chemical and volume control system. The alternating systems exhibit strong dynamic time-dependent reliability characteristics because of the alternating operational mode and the technical specification requirements that are particularly difficult to analyze by static fault-tree techniques. The method used in this paper is based on the semi-Markov reliability analysis. The system performance measures evaluated are its contribution to the total risk of the plant (e.g., core damage probability) and to plant unavailability (reactor downtime). It is concluded that the methodology developed in this study can be applied to existing alternating systems for plant-specific evaluation of the various alternatives in technical specifications.

  11. A semi-automated vascular access system for preclinical models

    NASA Astrophysics Data System (ADS)

    Berry-Pusey, B. N.; Chang, Y. C.; Prince, S. W.; Chu, K.; David, J.; Taschereau, R.; Silverman, R. W.; Williams, D.; Ladno, W.; Stout, D.; Tsao, T. C.; Chatziioannou, A.

    2013-08-01

    Murine models are used extensively in biological and translational research. For many of these studies it is necessary to access the vasculature for the injection of biologically active agents. Among the possible methods for accessing the mouse vasculature, tail vein injections are a routine but critical step for many experimental protocols. To perform successful tail vein injections, a high skill set and experience is required, leaving most scientists ill-suited to perform this task. This can lead to a high variability between injections, which can impact experimental results. To allow more scientists to perform tail vein injections and to decrease the variability between injections, a vascular access system (VAS) that semi-automatically inserts a needle into the tail vein of a mouse was developed. The VAS uses near infrared light, image processing techniques, computer controlled motors, and a pressure feedback system to insert the needle and to validate its proper placement within the vein. The VAS was tested by injecting a commonly used radiolabeled probe (FDG) into the tail veins of five mice. These mice were then imaged using micro-positron emission tomography to measure the percentage of the injected probe remaining in the tail. These studies showed that, on average, the VAS leaves 3.4% of the injected probe in the tail. With these preliminary results, the VAS system demonstrates the potential for improving the accuracy of tail vein injections in mice.

  12. Semi-automated software service integration in virtual organisations

    NASA Astrophysics Data System (ADS)

    Afsarmanesh, Hamideh; Sargolzaei, Mahdi; Shadi, Mahdieh

    2015-08-01

    To enhance their business opportunities, organisations involved in many service industries are increasingly active in pursuit of both online provision of their business services (BSs) and collaborating with others. Collaborative Networks (CNs) in service industry sector, however, face many challenges related to sharing and integration of their collection of provided BSs and their corresponding software services. Therefore, the topic of service interoperability for which this article introduces a framework is gaining momentum in research for supporting CNs. It contributes to generation of formal machine readable specification for business processes, aimed at providing their unambiguous definitions, as needed for developing their equivalent software services. The framework provides a model and implementation architecture for discovery and composition of shared services, to support the semi-automated development of integrated value-added services. In support of service discovery, a main contribution of this research is the formal representation of services' behaviour and applying desired service behaviour specified by users for automated matchmaking with other existing services. Furthermore, to support service integration, mechanisms are developed for automated selection of the most suitable service(s) according to a number of service quality aspects. Two scenario cases are presented, which exemplify several specific features related to service discovery and service integration aspects.

  13. A Semi-automated Abundance Survey of Ap Stars

    NASA Astrophysics Data System (ADS)

    Hall, Martin P.; Kurtz, Don; Elkin, Vladimir; Bruntt, Hans

    2015-08-01

    We have carried out an abundance analysis on the high-resolution spectra of approximately 350 Ap stars collected between 2007 and 2010 on the FEROS Echelle (Fibre-led, Extended Range, Echelle ) spectrograph housed at the 2.2-m telescope at European Southern Observatory at La Silla, Chile. We employed the VWA package (vsin I, wavelength shift, abundance analysis) for preliminary selection of spectral lines, and a semi-automated set of routines which we developed in the programming language IDL, to calculate the equivalent widths and abundances of ions of Iron and the rare earth elements Neodymium and Praseodymium using the WIDTH program and NEMO model atmospheres. Initial results are presented, which reinforce the correlation between iron abundance and effective temperature, from an over-abundance in the late Bp stars, to under-abundant in the early F stars. Results also suggest that the disequilibrium in abundances of the first and second ionisation stages of these ions in the rapidly oscillating Ap (roAp) stars may a consequence of the relatively cool temperatures of those stars, rather than a signature of pulsation.

  14. DPpackage: Bayesian Semi- and Nonparametric Modeling in R

    PubMed Central

    Jara, Alejandro; Hanson, Timothy E.; Quintana, Fernando A.; Müller, Peter; Rosner, Gary L.

    2011-01-01

    Data analysis sometimes requires the relaxation of parametric assumptions in order to gain modeling flexibility and robustness against mis-specification of the probability model. In the Bayesian context, this is accomplished by placing a prior distribution on a function space, such as the space of all probability distributions or the space of all regression functions. Unfortunately, posterior distributions ranging over function spaces are highly complex and hence sampling methods play a key role. This paper provides an introduction to a simple, yet comprehensive, set of programs for the implementation of some Bayesian non- and semi-parametric models in R, DPpackage. Currently DPpackage includes models for marginal and conditional density estimation, ROC curve analysis, interval-censored data, binary regression data, item response data, longitudinal and clustered data using generalized linear mixed models, and regression data using generalized additive models. The package also contains functions to compute pseudo-Bayes factors for model comparison, and for eliciting the precision parameter of the Dirichlet process prior. To maximize computational efficiency, the actual sampling for each model is carried out using compiled FORTRAN. PMID:21796263

  15. Using NDVI to measure precipitation in semi-arid landscapes

    USGS Publications Warehouse

    Birtwhistle, Amy N.; Laituri, Melinda; Bledsoe, Brian; Friedman, Jonathan M.

    2016-01-01

    Measuring precipitation in semi-arid landscapes is important for understanding the processes related to rainfall and run-off; however, measuring precipitation accurately can often be challenging especially within remote regions where precipitation instruments are scarce. Typically, rain-gauges are sparsely distributed and research comparing rain-gauge and RADAR precipitation estimates reveal that RADAR data are often misleading, especially for monsoon season convective storms. This study investigates an alternative way to map the spatial and temporal variation of precipitation inputs along ephemeral stream channels using Normalized Difference Vegetation Index (NDVI) derived from Landsat Thematic Mapper imagery. NDVI values from 26 years of pre- and post-monsoon season Landsat imagery were derived across Yuma Proving Ground (YPG), a region covering 3,367 km2 of semiarid landscapes in southwestern Arizona, USA. The change in NDVI from a pre-to post-monsoon season image along ephemeral stream channels explained 73% of the variance in annual monsoonal precipitation totals from a nearby rain-gauge. In addition, large seasonal changes in NDVI along channels were useful in determining when and where flow events have occurred.

  16. Chemical composition of semi-regular variable giants. III.

    NASA Astrophysics Data System (ADS)

    Britavskiy, N. E.; Andrievsky, S. M.; Tsymbal, V. V.; Korotin, S. A.; Martin, P.; Andrievska, A. S.

    2012-06-01

    Aims: We derive the stellar atmosphere parameters and chemical element abundances of four stars classified as semi-regular variables of type "d" (SRd). These stars should presumably belong to the Galactic halo population. Methods: Elemental abundances are derived by applying both local thermodynamical equilibrium and non-local thermodynamical equilibrium analyses to high resolution (R ≈ 80 000) spectra obtained with the CFHT ESPaDOnS spectrograph. We determine the abundances of 27 chemical elements in VW Dra, FT Cnc, VV LMi, and MQ Hya. Results: The stars of our present program have a chemical composition that is inconsistent with their presumable status as metal-deficient halo giants. All studied SRd giants have relative-to-solar elemental abundances that are typical of the thick/thin Galactic disk stars. We find that all objects of this class for which spectroscopic follow up analyses have been completed show a dichotomy in the amplitudes of their photometric variations. Specifically, the disk objects have small amplitudes, while halo SRd stars have much larger amplitudes, which indicates that amplitude is obviously related to the metallicity of the star. Based on observations obtained at the Canada-France-Hawaii Telescope (CFHT), which is operated by the National Research Council of Canada, the Institut National des Sciences de l'Univers of the Centre National de la Recherche Scientifique of France, and the University of Hawaii.Figures 2 and 3 are available in electronic form at http://www.aanda.org

  17. Semi-automatic development of Payload Operations Control Center software

    NASA Technical Reports Server (NTRS)

    Ballin, Sidney

    1988-01-01

    This report summarizes the current status of CTA's investigation of methods and tools for automating the software development process in NASA Goddard Space Flight Center, Code 500. The emphasis in this effort has been on methods and tools in support of software reuse. The most recent phase of the effort has been a domain analysis of Payload Operations Control Center (POCC) software. This report summarizes the results of the domain analysis, and proposes an approach to semi-automatic development of POCC Application Processor (AP) software based on these results. The domain analysis enabled us to abstract, from specific systems, the typical components of a POCC AP. We were also able to identify patterns in the way one AP might be different from another. These two perspectives--aspects that tend to change from AP to AP, and aspects that tend to remain the same--suggest an overall approach to the reuse of POCC AP software. We found that different parts of an AP require different development technologies. We propose a hybrid approach that combines constructive and generative technologies. Constructive methods emphasize the assembly of pre-defined reusable components. Generative methods provide for automated generation of software from specifications in a very-high-level language (VHLL).

  18. Enhanced adaptive focusing through semi-transparent media

    PubMed Central

    Di Battista, Diego; Zacharakis, Giannis; Leonetti, Marco

    2015-01-01

    Adaptive optics can focus light through opaque media by compensating the random phase delay acquired while crossing a scattering curtain. The technique is commonly exploited in many fields, including astrophysics, microscopy, biomedicine and biology. A turbid lens has the capability of producing foci with a resolution higher than conventional optics, however it has a fundamental limit: to obtain a sharp focus one has to introduce a strongly scattering medium in the optical path. Indeed a tight focusing needs strong scattering and, as a consequence, high resolution focusing is obtained only for weakly transmitting samples. Here we describe a novel method allowing to obtain highly concentrated optical spots even by introducing a minimum amount of scattering in the beam path with semi-transparent materials. By filtering the pseudo-ballistic components of the transmitted beam we are able to experimentally overcome the limits of the adaptive focus resolution, gathering light on a spot with a diameter which is one third of the original speckle correlation function. PMID:26620906

  19. Semi-automatic recognition of marine debris on beaches

    NASA Astrophysics Data System (ADS)

    Ge, Zhenpeng; Shi, Huahong; Mei, Xuefei; Dai, Zhijun; Li, Daoji

    2016-05-01

    An increasing amount of anthropogenic marine debris is pervading the earth’s environmental systems, resulting in an enormous threat to living organisms. Additionally, the large amount of marine debris around the world has been investigated mostly through tedious manual methods. Therefore, we propose the use of a new technique, light detection and ranging (LIDAR), for the semi-automatic recognition of marine debris on a beach because of its substantially more efficient role in comparison with other more laborious methods. Our results revealed that LIDAR should be used for the classification of marine debris into plastic, paper, cloth and metal. Additionally, we reconstructed a 3-dimensional model of different types of debris on a beach with a high validity of debris revivification using LIDAR-based individual separation. These findings demonstrate that the availability of this new technique enables detailed observations to be made of debris on a large beach that was previously not possible. It is strongly suggested that LIDAR could be implemented as an appropriate monitoring tool for marine debris by global researchers and governments.

  20. Semi-span model testing in the national transonic facility

    NASA Astrophysics Data System (ADS)

    Chokani, Ndaona

    1994-05-01

    The present work was motivated by an ongoing research program at NASA Langley Research Center to develop a semi-span testing capability for the National Transonic Facility (NTF). This test technique is being investigated as a means to design and optimize high-lift devices at flight Reynolds numbers in a ground test facility. Even though the freestream Mach numbers of interest are around .20, the flow around a transport wing with high lift devices deployed may contain regions of compressible flow. Thus to properly model the flow physics, a compressible flow solver may be required. However, the application of a compressible flow solver at low Mach numbers can be problematic. The objective of this phase of the project is to directly compare the performance of two widely used three-dimensional compressible Navier-Stokes solvers at low Mach numbers to both experimental data and to results obtained from an incompressible Navier-Stokes solver. The geometries of interest are two isolated wings with different leading edge sweep angles. The compressible Navier-Stokes solvers chosen, TLNS3D-MB and CFL3D, which were developed at NASA Langley Research Center (LaRC), represent the current state-of-the-art in compressible 3-D Navier-Stokes solvers. The incompressible Navier-Stokes solver, INS3D-UP, developed recently at NASA Ames Research Center (ARC), represents the current state-of-the-art in incompressible Navier-Stokes solvers.