Science.gov

Sample records for 13-8 mo stainless

  1. The influence of palladium on the hydrogen-assisted cracking resistance of PH 13-8 Mo stainless steel

    NASA Astrophysics Data System (ADS)

    Scully, J. R.; van den Avyle, J. A.; Cieslak, M. J.; Romig, A. D.; Hills, C. R.

    1991-10-01

    We compare the hydrogen-assisted cracking resistance of wrought PH 13-8 Mo stainless steel alloyed with 0.4 to 1.0 wt pct palladium to the conventional alloy when aged to yield strengths of 1170 to 1250 MPa. Intergranular hydrogen cracking is suppressed with Pd in both static load and constant extension rate tests conducted with electrochemical hydrogen charging. These results are analyzed to elucidate the role of Pd in suppressing intergranular cracking. Palladium is found both in substitutional solid solution in the martensitic phase and also in the form of randomly distributed PdAl precipitates in all Pd-modified alloys. Interfacial segregation of Pd to grain boundaries and lath boundaries is not observed at any levels above a detection limit of approximately 0.5 monolayers. Hydrogen permeation analyses indicate that hydrogen ingress is not inhibited by Pd but that apparent diffusion coefficients are lowered relative to the conventional alloy. Lower diffusion coefficients are consistent with the creation of a strong but reversible hydrogen trap, identified as the uniformly distributed PdAl phase. We hypothesize that PdAl trap sites force a redistribution of trapped hydrogen, which lowers the amount of interfacially segregated hydrogen at prior austenite grain boundaries for the electrochemical conditions applied. These assertions are supported by a simplistic trapping model for PH 13-8 Mo which shows that both the hydrogen trap binding energy and the trap density for the PdAl trapping site are greater than the hydrogen trap binding energy and density for prior austenite grain boundaries.

  2. Heat treatment of investment cast PH 13-8 Mo stainless steel: Part II. Isothermal aging kinetics

    NASA Astrophysics Data System (ADS)

    Robino, C. V.; Cieslak, M. J.; Hochanadel, P. W.; Edwards, G. R.

    1994-04-01

    The hardening response of investment cast PH 13-8 Mo stainless steel has been evaluated by hardness measurements following aging in the temperature range normally specified for this alloy (510 °C to 593 °C). A new relationship between fraction transformed and hardness was developed, and analysis of the data in terms of the kinetics of precipitation, in a manner similar to that frequently applied to other precipitation-hardenable martensitic steels, yielded low time exponents and a low value for the apparent activation energy. The values of the time exponents were 0.49, 0.37, 0.56, and 0.53 at 510 °C, 538 °C, 566 °C, and 593 °C, respectively, and that for the apparent activation energy was 139 kJ/mole. As has been proposed for other maraging type steels, these estimates suggest that Β-NiAl precipitates along or near dislocations and that growth of the precipitates is dominated by dislocation pipe diffusion. However, these predictions were neither supported nor refuted by transmission electron microscopy (TEM) because of difficulties in imaging the Β-NiAl precipitates at the aging times and temperatures used. Further, analysis of the data using the formalism of Wert and Zener for the growth of precipitates with interfering diffusion fields indicated that the estimates of fraction transformed from hardness data are not fully appropriate for maraging type steels. Consideration of the nature of the Avrami analysis and the electron microscopy results suggests that other phenomena, including dislocation recovery and reversion of martensite to austenite, occur at rates sufficient to convolute the Avrami analysis. It is further suggested that these results cast doubt on the fundamental implications of previous analyses of precipitation kinetics in age-hardening martensitic steels. Although the Avrami analysis was found not to provide a tenable description of the precipitation kinetics, it does provide a reasonable methodology for portrayal of the hardening response

  3. Heat treatment of investment cast PH 13-8 Mo stainless steel: Part I. Mechanical properties and microstructure

    NASA Astrophysics Data System (ADS)

    Hochanadel, P. W.; Edwards, G. R.; Robino, C. V.; Cieslak, M. J.

    1994-04-01

    The microstructure of investment cast PH 13-8 Mo stainless steel heat-treated to various conditions was studied using light and electron microscopy, electron probe microanalysis, and Mössbauer spectroscopy. The mechanical properties were investigated by using uniaxial tensile testing, hardness testing, and Charpy impact testing. The Β-NiAl strengthening precipitates, though detectable by electron diffraction, were difficult to resolve by transmission electron microscopy (TEM) in specimens aged at low temperatures (566 °C and below). A high dislocation density was observed in the lath martensitic structure. The higher strength and lower ductility observed at low aging temperatures was attributed to both the high dislocation density and the precipitation of Β-NiAl. When samples were aged at high temperatures (> 566 °C), a lower dislocation density and a reverted austenite fraction on the order of 15 pct were observed. Spherical Β-NiAl precipitates were observed in the overaged condition. The decrease in strength and corresponding increase in ductility observed in samples aged at temperatures above 566 °C were attributed to the reverted austenite and recovery. Mechanical properties were improved when the homogenizing temperature and time were increased. Electron probe microanalysis quantified the increased homogeneity realized by increasing homogenizing temperature and time. Elimination of the refrigeration step, which normally follows the solution treatment, did not degrade the mechanical properties. Mössbauer spectroscopy showed only minor decreases in the fraction of retained austenite when refrigeration followed the solution treatment.

  4. Heat treatment of investment cast PH 13-8 Mo stainless steel; Part 2: Isothermal aging kinetics

    SciTech Connect

    Robino, C.V.; Cieslak, M.J. . Physical and Joining Metallurgy Dept.); Hochanadel, P.W.; Edwards, G.R. . Dept. of Metallurgical and Materials Engineering)

    1994-04-01

    The hardening response of investment cast PH 13-8 Mo stainless steel has been evaluated by hardness measurements following aging in the temperature range normally specified for this alloy (510 C to 593 C). A new relationship between fraction transformed and hardness was developed, and analysis of the data in terms of the kinetics of precipitation, in a manner similar to that frequently applied to other precipitation-hardenable martensitic steels, yielded low time exponents and a low value for the apparent activation energy. The values of the time exponents were 0.49, 0.37, 0.56, and 0.53 at 510 C, 538 C, 566 C, and 593 C, respectively, and that for the apparent activation energy was 139 kJ/mole. As has been proposed for other maraging type steels, these estimates suggest that [beta]-NiAl precipitates along or near dislocations and that growth of the precipitates is dominated by dislocation pipe diffusion. However, these predictions were neither supported nor refuted by transmission electron microscopy (TEM) because of difficulties in imaging the [beta]-NiAl precipitates at the aging times and temperatures used. Further, analysis of the data using the formalism of Wert and Zener for the growth of precipitates with interfering diffusion fields indicated that the estimates of fraction transformed from hardness data are not fully appropriate for maraging type steels. Consideration of the nature of the Avrami analysis and the electron microscopy results suggests that other phenomena, including dislocation recovery and reversion of martensite to austenite, occur at rates sufficient to convolute the Avrami analysis. It is further suggested that these results cast doubt on the fundamental implications of previous analyses of precipitation kinetics in age-hardening martensitic steels.

  5. Stress corrosion study of PH13-8Mo stainless steel using the Slow Strain Rate Technique

    NASA Technical Reports Server (NTRS)

    Torres, Pablo D.

    1989-01-01

    The need for a fast and reliable method to study stress corrosion in metals has caused increased interest in the Slow Strain Rate Technique (SSRT) during the last few decades. PH13-8MoH950 and H1000 round tensile specimens were studied by this method. Percent reduction-in-area, time-to-failure, elongation at fracture, and fracture energy were used to express the loss in ductility, which has been used to indicate susceptibility to stress corrosion cracking (SCC). Results from a 3.5 percent salt solution (corrosive medium) were compared to those in air (inert medium). A tendency to early failure was found when testing in the vicinity of 1.0 x 10(-6) mm/mm/sec in the 3.5 percent salt solution. PH13-8Mo H1000 was found to be less likely to suffer SCC than PH13-8Mo H950. This program showed that the SSRT is promising for the SCC characterization of metals and results can be obtained in much shorter times (18 hr for PH steels) than those required using conventional techniques.

  6. An investigation of the high-temperature and solidification microstructures of PH 13-8 Mo stainless steel

    NASA Astrophysics Data System (ADS)

    Cieslak, M. J.; Hills, C. R.; Hlava, P. F.; David, S. A.

    1990-09-01

    Differential thermal analysis (DTA), high-temperature water-quench (WQ) experiments, and optical and electron microscopy were used to establish the near-solidus and solidification microstructures in PH 13-8 Mo. On heating at a rate of 0. 33 °C/s, this alloy begins to transform from austenite to δ-ferrite at ≈1350 °C. Transformation is complete by ≈1435 °C. The solidus is reached at ≈1447 °C, and the liquidus is ≈1493 °C. On cooling from the liquid state at a rate of 0. 33 °C/s, solidification is completed as δ-ferrite with subsequent transformation to austenite beginning in the solid state at ≈1364 °C. Insufficient time at temperature is available for complete transformation and the resulting room-temperature microstructure consists of matrix martensite (derived from the shear decomposition of the austenite) and residual δ-ferrite. The residual δ-ferrite in the DTA sample is enriched in Cr (≈16 wt pct), Mo (≈4 wt pct), and Al (≈1. 5 wt pct) and depleted in Ni (≈4 wt pct) relative to the martensite (≈12. 5 wt pct Cr, ≈2 wt pct Mo, ≈1 wt pct Al, ≈9 wt pct Ni). Solid-state transformation of δ σ γ was found to be quench-rate sensitive with large grain, fully ferritic microstructures undergoing a massive transformation as a result of water quenching, while a diffusionally controlled Widmanstätten structure was produced in air-cooled samples.

  7. Gaseous hydrogen embrittlement of PH 13-8 Mo steel

    NASA Astrophysics Data System (ADS)

    Ding, Y. S.; Tsay, L. W.; Chiang, M. F.; Chen, C.

    2009-04-01

    In this study, notched tensile and fatigue crack growth tests in gaseous hydrogen were performed on PH 13-8 Mo stainless steel specimens at room temperature. These specimens were susceptible to hydrogen embrittlement (HE), but at different degrees, depending on the aging conditions or the microstructures of the alloys. In hydrogen, the accelerated fatigue crack growth rate (FCGR) usually accompanied a reduced notched tensile strength (NTS) of the specimens, i.e., the faster the FCGR the lower the NTS. It was proposed that the same fracture mechanism could be applied to these two different types of specimens, regardless of the loading conditions. Rapid fatigue crack growth and high NTS loss were found in the H800 (426 °C under-aged) and H900 (482 °C peak-aged) specimens. The HE susceptibility of the steel was reduced by increasing the aging temperature above 593 °C, which was attributed to the increased amount of austenite in the structure. Extensive quasi-cleavage fracture was observed for the specimens that were deteriorated severely by HE.

  8. The characterization of small fatigue crack growth in PH13-8 molybdenum stainless steel

    NASA Astrophysics Data System (ADS)

    Jin, Ohchang

    The rotor hubs of Navy CH-46 helicopters have been made of 4340 steel and had extensive corrosion fatigue problems. Since these helicopters have to be used until the year 2020, the Navy decided to replace 4340 steel with PH 13-8 Mo stainless steel. Because the rotors are exposed to high frequency high cycle fatigue, small fatigue cracks are important in estimating remaining lifetime of the components. The objective of this study was to characterize the small crack growth behavior in the PH 13-8 Mo stainless steel under various loading conditions. Constant amplitude loading was conducted at the stress ratios, R, 0.1 and 0.4. The crack growth rate was affected by the microstructures in early stage of the growth, mainly by the size of the martensite packets and oscillated up to the crack length of 200 mum. It was found that the crack growth rate was little influenced by the stress amplitudes and stress ratios. In addition, the small crack growth rate was found to be similar to the long crack growth rate at R = 0.1 and 0.4. Overload tests and simple block loading were performed to understand load interaction effects on the small crack growth rate. The overload tests indicated that the crack growth rate was little affected by the overload. This might result from the fact that the overload ratio used in this study was low (<1.3). However, the results of the simple block loading showed overall crack growth retardation. The compressive residual stress present at the notch root of the specimen tested at R = 0.1 may lower the effective stress ratio, Reff, from 0.1 to negative R, and may result in the crack growth retardation. The small crack growth behavior was also examined under the saltwater. There was no difference in the crack growth rate between under air and under saltwater. In addition, the crack growth rate of the specimens tested under the saltwater was not affected by the test frequencies of 10, 1 and 0.1 Hz. It was shown that under the saltwater the PH 13-8 Mo

  9. The partitioning of alloying elements in vacuum arc remelted, Pd-modified PH 13-8 Mo alloys

    NASA Astrophysics Data System (ADS)

    Cieslak, M. J.; Vandenavyle, J. A.; Carr, M. J.; Hills, C. R.; Semarge, R. E.

    1988-12-01

    The partitioning of alloying elements in as-solidified PH 13-8 Mo stainless steel containing up to 1.02 wt pct Pd has been investigated. The as-solidified structure is composed of two major phases, martensite and ferrite. Electron probe microanalysis reveals that Mo, Cr, and Al partition to the ferrite phase while Fe, Ni, Mn, and Pd partition to the martensite (prior austenite) during solidification and cooling from the solidus. In addition to bulk segregation between phases, precipitation of the intermetallic, PdAI, in the retained ferrite is observed. Precipitation of the normal hardening phase, β-NiAl, is also observed in the retained ferrite. Partition ratios of the various alloying elements are determined and are compared with those observed previously in duplex Fe-Cr-Ni stainless steel solidification structures. The martensite start temperature (Ms) was observed to decrease with increasing Pd concentration.

  10. Vacuum investment cast PH13-8Mo corrosion resistant steel. (SAE standard)

    SciTech Connect

    1991-07-01

    An industry-wide interest has arisen with regards to the properties and capabilities of investment cast PH 13-8Mo corrosion resistant steel. Specifically of interest are the structural applications in the aerospace industry for this product heat treated to the H1000 condition. The objective of this AMEC cooperative test program was to generate and compile useful data for aerospace structural evaluation of investment cast PH 13-8Mo heat treated to H1000. The determination was made of overall mechanical properties, fatigue, fracture toughness, and crack growth data along with basic microstructural evaluation of the investment cast material. The evaluation of mechanical property variations between cast and machined tensile specimens and evaluation of microstructural constituents. PH 13-8Mo, H1000 investment castings for use in the aerospace industry is included.

  11. The dimensional stability analysis of seventeen stepped specimens of 18Ni 200 grade, PH13-8Mo and A-286

    NASA Technical Reports Server (NTRS)

    Wigley, D. A.

    1983-01-01

    This report documents the results of a dimensional stability analysis of seventeen stepped specimens that were used in the evaluation of factors influencing warpage in metallic alloys being used for cryogenic wind tunnel models. Specimens used in the analysis were manufactured from 18Ni 200 Grade Maaraging steel, PH13-8Mo, and A-286 stainless steel. Quantitative data are provided on the behavior of the specimens due to the effects of both machining and cryogenic cycling effects.

  12. Machining-induced deformation in stepped specimens of PH 13-8 Mo, 18 nickel maraging steel grade 200T1 and grain-refined HP 9-4-20

    NASA Technical Reports Server (NTRS)

    Wigley, D. A.

    1985-01-01

    The results of a study to evaluate the dimensional changes created during machining and subsequent cycling to cryogenic temperatures for three different metallic alloys are presented. Experimental techniques are described and results presented for 18 Ni Grade 200 maraging steel, PH-13-8 Mo stainless steel, and Grain-refined HP 9-4-20.

  13. Plane Shock Generator Explosive Lens: Shock characterization of 4340 and PH13-8Mo steels, C360 brass and PZT 65/35 ferro-electric ceramic

    SciTech Connect

    Weirick, L.J.

    1994-03-01

    Sandia National Laboratories is currently involved in the optimization of a Plane Shock Generator Explosive Lens (PSGEL). The PSGEL component consists of a detonator, explosive, brass cone and tamper housing. The purpose of the PSGEL component is to transmit a plane shock wave through the 4340 steel bulkhead (wave separator) which has a ferro-electric (PZT)ceramic disk attached to the opposite surface of the steel bulkhead. The planar shock wave depolarizes the PZT 65/35 ferro-electric ceramic to produce an electrical output. One aspect of the optimization program involves the possible replacement of 4340 steel with PH13-8Mo steel for the bulkhead. These materials, as well as the PZT 65/35 ferro-electric ceramic and the brass for the cone, required the stock characterization with respect to Hugoniot parameters. The work presented here gives the shock Hugoniot values for these four materials and documents their measurements.

  14. A XPS study of the Mo effect on passivation behaviors for highly controlled stainless steels in neutral and alkaline conditions

    NASA Astrophysics Data System (ADS)

    Mesquita, Thiago J.; Chauveau, Eric; Mantel, Marc; Nogueira, Ricardo P.

    2013-04-01

    The objective of this work is to study the effect of Mo additions on film passive properties of three different stainless steels (SS) types (austenitic, ferritic and duplex alloys). A comparison between Mo containing (3 wt% Mo) and free Mo (0 wt% Mo) grades of highly controlled laboratory heats was done considering their passive film formed in different aggressive conditions, from neutral to alkaline pH. The presence of oxidized Mo on the passive layer was confirmed by X-ray photoelectron Spectroscopy (XPS). The presence of Mo within the passive film improved the passivity breakdown potential for the duplex and ferritic SS, but seemed to have no effect for austenitic SS.

  15. Interfacial Phenomena in Fe/Stainless Steel-TiC Systems and the Effect of Mo

    NASA Astrophysics Data System (ADS)

    Kiviö, Miia; Holappa, Lauri; Yoshikawa, Takeshi; Tanaka, Toshihiro

    2014-12-01

    Titanium carbide is used as reinforcement particles in composites due to its hardness, wear resistance and stability. This work is a part of the study in which titanium carbides are formed in stainless steel castings in the mold to improve the wear resistance of a certain surface of the casting. Such local reinforcement is a very potential method but it is a quite demanding task requiring profound knowledge of interfacial phenomena in the system, wettability, stability, dissolution and precipitation of new phases in production of these materials. Good wetting between different constituents in the material is a key factor to attain maximal positive effects. Mo is used with TiC or Ti(C,N) reinforcement in composites to improve wettability. In this work the effect of Mo on the phenomena in Fe/stainless steel-TiC systems was examined by wetting experiments between the substrate and the alloy. Wetting was not significantly improved by adding Mo to the systems. Core-rim type carbides as well as more homogenous carbide particles were observed. Overall the carbide particles are very complex regarding to their chemistry, size and shape which aspects have to be taken into account in the development of these materials and manufacturing processes.

  16. 40 CFR 13.8 - Collection rule.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 1 2013-07-01 2013-07-01 false Collection rule. 13.8 Section 13.8 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GENERAL CLAIMS COLLECTION STANDARDS Collection § 13.8 Collection rule. (a) The Administrator takes action to collect all debts owed the United...

  17. 40 CFR 13.8 - Collection rule.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Collection rule. 13.8 Section 13.8 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GENERAL CLAIMS COLLECTION STANDARDS Collection § 13.8 Collection rule. (a) The Administrator takes action to collect all debts owed the United...

  18. 40 CFR 13.8 - Collection rule.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 1 2014-07-01 2014-07-01 false Collection rule. 13.8 Section 13.8 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GENERAL CLAIMS COLLECTION STANDARDS Collection § 13.8 Collection rule. (a) The Administrator takes action to collect all debts owed the United...

  19. 40 CFR 13.8 - Collection rule.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 1 2012-07-01 2012-07-01 false Collection rule. 13.8 Section 13.8 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GENERAL CLAIMS COLLECTION STANDARDS Collection § 13.8 Collection rule. (a) The Administrator takes action to collect all debts owed the United...

  20. 40 CFR 13.8 - Collection rule.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 1 2011-07-01 2011-07-01 false Collection rule. 13.8 Section 13.8 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GENERAL CLAIMS COLLECTION STANDARDS Collection § 13.8 Collection rule. (a) The Administrator takes action to collect all debts owed the United...

  1. 47 CFR 13.8 - Authority conveyed.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false Authority conveyed. 13.8 Section 13.8 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL COMMERCIAL RADIO OPERATORS General § 13.8 Authority conveyed. Licenses, certificates and permits issued under this part convey authority for the...

  2. Effect of tempering temperature on properties of 00Cr16Ni5Mo stainless steel

    SciTech Connect

    Qin, B. Wang, Z.Y.; Sun, Q.S.

    2008-08-15

    Specimens of 00Cr16Ni5Mo low carbon martensitic stainless steel were normalized at 1000 deg. C followed by tempering at 525 deg. C, 550 deg. C, 575 deg. C, 600 deg. C and 625 deg. C. After heat treatment, mechanical properties and pitting potential were determined through tensile, impact and electrochemical polarization tests. The results showed that the samples tempered at 550 deg. C and 600 deg. C for 2 h had an excellent combination of tensile strength, elongation, impact energy, hardness and corrosion resistance. Scanning electron microscopy, and X-ray diffraction examinations were conducted. These revealed that the properties of the steel were affected by the structure of the lath martensite, {delta}-ferrite, retained austenite and carbides.

  3. Austenite Formation from Martensite in a 13Cr6Ni2Mo Supermartensitic Stainless Steel

    NASA Astrophysics Data System (ADS)

    Bojack, A.; Zhao, L.; Morris, P. F.; Sietsma, J.

    2016-05-01

    The influence of austenitization treatment of a 13Cr6Ni2Mo supermartensitic stainless steel (X2CrNiMoV13-5-2) on austenite formation during reheating and on the fraction of austenite retained after tempering treatment is measured and analyzed. The results show the formation of austenite in two stages. This is probably due to inhomogeneous distribution of the austenite-stabilizing elements Ni and Mn, resulting from their slow diffusion from martensite into austenite and carbide and nitride dissolution during the second, higher temperature, stage. A better homogenization of the material causes an increase in the transformation temperatures for the martensite-to-austenite transformation and a lower retained austenite fraction with less variability after tempering. Furthermore, the martensite-to-austenite transformation was found to be incomplete at the target temperature of 1223 K (950 °C), which is influenced by the previous austenitization treatment and the heating rate. The activation energy for martensite-to-austenite transformation was determined by a modified Kissinger equation to be approximately 400 and 500 kJ/mol for the first and the second stages of transformation, respectively. Both values are much higher than the activation energy found during isothermal treatment in a previous study and are believed to be effective activation energies comprising the activation energies of both mechanisms involved, i.e., nucleation and growth.

  4. Corrosion Behavior of High Nitrogen Nickel-Free Fe-16Cr-Mn-Mo-N Stainless Steels

    NASA Astrophysics Data System (ADS)

    Chao, K. L.; Liao, H. Y.; Shyue, J. J.; Lian, S. S.

    2014-04-01

    The purpose of the current study is to develop austenitic nickel-free stainless steels with lower chromium content and higher manganese and nitrogen contents. In order to prevent nickel-induced skin allergy, cobalt, manganese, and nitrogen were used to substitute nickel in the designed steel. Our results demonstrated that manganese content greater than 14 wt pct results in a structure that is in full austenite phase. The manganese content appears to increase the solubility of nitrogen; however, a lower corrosion potential was found in steel with high manganese content. Molybdenum appears to be able to increase the pitting potential. The effects of Cr, Mn, Mo, and N on corrosion behavior of Fe-16Cr-2Co-Mn-Mo-N high nitrogen stainless steels were evaluated with potentiodynamic tests and XPS surface analysis. The results reveal that anodic current and pits formation of the Fe-16Cr-2Co-Mn-Mo-N high nitrogen stainless steels were smaller than those of lower manganese and nitrogen content stainless steel.

  5. The effects of sulfate reducing bacteria on stainless steel and Ni-Cr-Mo alloy weldments

    SciTech Connect

    Petersen, T.A.; Taylor, S.R.

    1995-10-01

    Previous research in this laboratory demonstrated a direct correlation between alloy composition and corrosion susceptibility of stainless steel and Ni-Cr-Mo alloy weldments exposed to lake water augmented with sulfate reducing bacteria (SRB). It was shown that lake water containing an active SRB population reduced the polarization resistance (R{sub p}) on all alloys studied including those with 9% Mo. In addition, preliminary evidence indicated that edge preparation and weld heat input were also important parameters in determining corrosion performance. This prior research, however, looked at ``doctored`` weldments in which the thermal oxide in the heat affected zone was removed. The objectives of the research presented here are to further confirm these observations using as-received welds. The materials examined (listed in increasing alloy content) are 1/4 inch thick plates of 316L, 317L, AL6XN (6% Mo), alloy 625 clad steel, alloy 625, and alloy 686. Materials were welded using the tungsten inert gas (TIG) process in an argon purged environment. In addition, 317L was welded in air to test oxide effects. All samples were prepared for welding by grinding to a V-edge, except the 625 clad steel samples which were prepared using a J-edge. Electrochemical performance of welded samples was monitored in four glass cells which could each allow exposure of 8 samples to the same environment. Two cells contained lake water inoculated with SRS, and two cells contained sterilized lake water. The open circuit potential (E{sub oc}) and R{sub p} was used to correlate corrosion susceptibility and bacterial activity with alloy composition and welding parameters.

  6. Effect of electroslag remelting on carbides in 8Cr13MoV martensitic stainless steel

    NASA Astrophysics Data System (ADS)

    Zhu, Qin-tian; Li, Jing; Shi, Cheng-bin; Yu, Wen-tao

    2015-11-01

    The effect of electroslag remelting (ESR) on carbides in 8Cr13MoV martensitic stainless steel was experimentally studied. Phases precipitated from liquid steel during solidification were calculated using the Thermo-Calc software. The carbon segregation was analyzed by original position analysis (OPA), and the carbides were analyzed by optical microscopy (OM), scanning electron microscopy (SEM), energy- dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD). The results indicated that more uniform carbon distribution and less segregation were obtained in the case of samples subjected to the ESR process. After ESR, the amount of netty carbides decreased significantly, and the chromium and vanadium contents in the grain-boundary carbides was reduced. The total area and average size of carbides were obviously smaller after the ESR process. In the sample subjected to ESR, the morphology of carbides changed from lamellar and angular to globular or lump, whereas the types of carbides did not change; both M23C6 and M7C3 were present before and after the ESR process.

  7. Corrosion behaviors of Mo coating on stainless steel 316 substrates implanted by different nitrogen ion fluences

    NASA Astrophysics Data System (ADS)

    Mojtahedzadeh Larijani, Madjid; Bafandeh, Nastaran

    2014-03-01

    The molybdenum nitride coating was produced by nitrogen ion implantation of the molybdenum layer deposited on the stainless steel 316 (SS) substrates. At first, molybdenum layers were deposited on the substrates by ion beam sputtering method, then nitrogen ions with an energy of 30 keV and a fluence between 1×1017 and 12×1017 N+ cm-2 were implanted in Mo/SS system. Crystal structure and topography of the surface are investigated by grazing incidence X-ray diffraction (GIXRD) and atomic force microscopy (AFM) image respectively. XRD patterns showed the formation of molybdenum nitride phases in all implanted samples. Corrosion tests showed that the corrosion resistance of the samples strongly depends on the nitrogen applied fluences. A considerable improvement of corrosion performance by increasing ions fluences was observed. The lowest corrosion current density with amount of 0.1 μA/cm2 was obtained at 12×1017 ions/cm2 fluence in our case.

  8. Effects of Mo content on microstructure and corrosion resistance of arc ion plated Ti-Mo-N films on 316L stainless steel as bipolar plates for polymer exchange membrane fuel cells

    NASA Astrophysics Data System (ADS)

    Zhang, Min; Kim, Kwang Ho; Shao, Zhigang; Wang, Feifei; Zhao, Shuang; Suo, Ni

    2014-05-01

    Bipolar plates are one of the most important components in PEMFC stack and have multiple functions, such as separators and current collectors, distributing reactions uniformly, and etc. Stainless steel is ideal candidate for bipolar plates owing to good thermal and electrical conductivity, good mechanical properties etc. However, stainless steel plate still cannot resist the corrosion of working condition. In this work, ternary Ti-Mo-N film was fabricated on 316L stainless steel (SS316L) as a surface modification layer to enhance the corrosion resistance. Effects of Mo content on the microstructure and corrosion resistance of Ti-Mo-N films are systematically investigated by altering sputtering current of the Mo target. XRD results reveal that the preferred orientation changes from [111] to [220] direction as Mo content in the film increases. The synthesized Ti-Mo-N films form a substitutional solid solution of (Ti, Mo)N where larger Mo atoms replace Ti in TiN crystal lattice. The TiN-coated SS316L sample shows the best corrosion resistance. While Mo content in the Ti-Mo-N films increases, the corrosion resistance gradually degrades. Compared with the uncoated samples, all the Ti-Mo-N film coated samples show enhanced corrosion resistance in simulated PEMFC working condition.

  9. Precipitation of Laves phase in a 28%Cr-4%Ni-2%Mo-Nb superferritic stainless steel

    SciTech Connect

    Fontoura de Andrade, Thiago; Madeira Kliauga, Andrea; Plaut, Ronald Lesley; Padilha, Angelo Fernando

    2008-05-15

    The main objective of the present work was to study the precipitation of the Laves phase in the X1 CrNiMoNb 28 4 2 (Werkstoff-Nr. DIN 1.4575) superferritic stainless steel employing several complementary techniques of microstructural analysis. The phase that precipitated in largest quantity in the DIN 1.4575 steel was the sigma ({sigma}) phase. However, along grain boundaries, after aging at 850 deg. C, a Laves phase of the MgZn{sub 2} type, with a hexagonal C14 crystal structure and chemical composition (Fe,Cr,Ni){sub 2}(Nb,Mo,Si), was also identified. Growth of the Laves phase is curtailed by exhaustion of niobium of the matrix and by the presence of the sigma phase, which also precipitates in the vicinity of the grain boundaries, however in larger amounts. No chi ({chi}) or austenite phases were detected in the temperature range studied.

  10. In-situ determination of austenite and martensite formation in 13Cr6Ni2Mo supermartensitic stainless steel

    SciTech Connect

    Bojack, A.; Zhao, L.; Morris, P.F.; Sietsma, J.

    2012-09-15

    In-situ analysis of the phase transformations in a 13Cr6Ni2Mo supermartensitic stainless steel (X2CrNiMoV13-5-2) was carried out using a thermo-magnetic technique, dilatometry and high temperature X-ray diffractometry (HT-XRD). A combination of the results obtained by the three applied techniques gives a valuable insight in the phase transformations during the austenitization treatment, including subsequent cooling, of the 13Cr6Ni2Mo supermartensitic stainless steel, where the magnetic technique offers a high accuracy in monitoring the austenite fraction. It was found by dilatometry that the austenite formation during heating takes place in two stages, most likely caused by partitioning of Ni into austenite. The in-situ evolution of the austenite fraction is monitored by high-temperature XRD and dilatometry. The progress of martensite formation during cooling was described with a Koistinen-Marburger relation for the results obtained from the magnetic and dilatometer experiments. Enhanced martensite formation at the sample surface was detected by X-ray diffraction, which is assumed to be due to relaxation of transformation stresses at the sample surface. Due to the high alloy content and high thermodynamic stability of austenite at room temperature, 4 vol.% of austenite was found to be stable at room temperature after the austenitization treatment. - Highlights: Black-Right-Pointing-Pointer We in-situ analyzed phase transformations and fractions of a 13Cr6Ni2Mo SMSS. Black-Right-Pointing-Pointer Higher accuracy of the austenite fraction was obtained from magnetic technique. Black-Right-Pointing-Pointer Austenite formation during heating takes place in two stages. Black-Right-Pointing-Pointer Enhanced martensite formation at the sample surface detected by X-ray diffraction.

  11. Erosion of a-C:H films deposited on W, Mo, and stainless steel under interaction with air glow discharge

    NASA Astrophysics Data System (ADS)

    Zalavutdinov, R. Kh.; Gorodetsky, A. E.; Bukhovets, V. L.; Zakharov, A. P.; Mazul, I. V.

    2011-08-01

    An air direct current glow discharge with a hollow cathode was used as source of chemically active oxygen for selective removal of amorphous hydrogenated (a-C:H) films deposited on W, Mo, and stainless steel. The films were removed both directly in the discharge and afterglow region. The film erosion rates depend on the sample position relatively to plasma and decrease in the order: hollow cathode, positive column, afterglow region. It was shown that primary (1-3 nm) continuous amorphous and secondary (1-30 nm) island-like oxide films were formed on the metal surfaces after removal of the a-C:H films. Polycrystalline island-like oxide films were generated due to recrystallization of the primary films. Material oxidation suppression was caused by reactions of oxygen ion neutralization and atomic oxygen recombination on metals.

  12. Comparative Study on the Corrosion Resistance of Fe-Based Amorphous Metal, Borated Stainless Steel and Ni-Cr-Mo-Gd Alloy

    SciTech Connect

    Lian, Tiangan; Day, Daniel; Hailey, Phillip; Choi, Jor-Shan; Farmer, Joseph

    2007-07-01

    Iron-based amorphous alloy Fe{sub 49.7}Cr{sub 17.7}Mn{sub 1.9}Mo{sub 7.4}W{sub 1.6}B{sub 15.2}C{sub 3.8}Si{sub 2.4} was compared to borated stainless steel and Ni-Cr-Mo-Gd alloy on their corrosion resistance in various high-concentration chloride solutions. The melt-spun ribbon of this iron-based amorphous alloy have demonstrated a better corrosion resistance than the bulk borated stainless steel and the bulk Ni-Cr-Mo-Gd alloy, in high-concentration chloride brines at temperatures 90 deg. C or higher. (authors)

  13. The high temperature three point bend testing of proton irradiated 316L stainless steel and Mod 9Cr 1Mo

    NASA Astrophysics Data System (ADS)

    Maloy, Stuart A.; Zubelewicz, A.; Romero, T.; James, M. R.; Sommer, W. F.; Dai, Y.

    2005-08-01

    The predicted operating conditions for a lead-bismuth eutectic target to be used in an accelerator driven system for the Advanced Fuel Cycle Initiative span a temperature range of 300-600 °C while being irradiated by a high energy (˜600 MeV) proton beam. Such spallation conditions lead to high displacement rates coupled with high accumulation rates of helium and hydrogen up to 150 appm/dpa. Some candidate materials for these applications include Mod9Cr-1Mo and 316L stainless steel. To investigate the effect of irradiation on these materials, the mechanical properties are being measured through three point bend testing on Mod 9Cr-1Mo and 316L at 25, 250, 350 and 500 °C after irradiation in a high energy proton beam (500-800 MeV) to a dose of 9.8 dpa at temperatures from 200 to 320 °C. By comparing measurements made in bending to tensile measurements measured on identically irradiated materials, a measurement of 0.2% offset yield stress was obtained from 0.05% offset yield stress measured in three point bend testing. Yield stress increased by more than a factor of two after irradiation to 9.8 dpa. Observation of the outer fiber surface of 316L showed very localized deformation when tested after irradiation at 70 °C and deformation on multiple slip systems when tested after irradiation at 250-320 °C.

  14. An Investigation of the Massive Transformation from Ferrite to Austenite in Laser-Welded Mo-Bearing Stainless Steels

    NASA Astrophysics Data System (ADS)

    Perricone, M. J.; Dupont, J. N.; Anderson, T. D.; Robino, C. V.; Michael, J. R.

    2011-03-01

    A series of 31 Mo-bearing stainless steel compositions with Mo contents ranging from 0 to 10 wt pct and exhibiting primary δ-ferrite solidification were analyzed over a range of laser welding conditions to evaluate the effect of composition and cooling rate on the solid-state transformation to γ-austenite. Alloys exhibiting this microstructural development sequence are of particular interest to the welding community because of their reduced susceptibility to solidification cracking and the potential reduction of microsegregation (which can affect corrosion resistance), all while harnessing the high toughness of γ-austenite. Alloys were created using the arc button melting process, and laser welds were prepared on each alloy at constant power and travel speeds ranging from 4.2 to 42 mm/s. The cooling rates of these processes were estimated to range from 10 K (°C)/s for arc buttons to 105 K (°C)/s for the fastest laser welds. No shift in solidification mode from primary δ-ferrite to primary γ-austenite was observed in the range of compositions or welding conditions studied. Metastable microstructural features were observed in many laser weld fusion zones, as well as a massive transformation from δ-ferrite to γ-austenite. Evidence of epitaxial massive growth without nucleation was also found when intercellular γ-austenite was already present from a solidification reaction. The resulting single-phase γ-austenite in both cases exhibited a homogenous distribution of Mo, Cr, Ni, and Fe at nominal levels.

  15. Investigation into the joining of MoSi{sub 2} to 316L stainless steel

    SciTech Connect

    Vaidya, R.U.; Bartlett, A.H.; Conzone, S.D.; Butt, D.P.

    1996-10-01

    Partial transient liquid phase joining and low temperature brazing were applied in joining MoSi{sub 2} to 316L ss. Exploratory studies were carried out on various interlayer materials. Mechanical, physical, and chemical compatibilities between various interlayers, brazing material, and substrate materials were investigated. Effect of thermal expansion mismatch between various components of the joint on the overall joint integrity was also studied. Preliminary findings are outlined.

  16. Corrosion Study of Super Ferritic Stainless Steel UNS S44660 (26Cr-3Ni-3Mo) and Several Other Stainless Steel Grades (UNS S31603, S32101, and S32205) in Caustic Solution Containing Sodium Sulfide

    NASA Astrophysics Data System (ADS)

    Chasse, Kevin R.; Singh, Preet M.

    2013-11-01

    Electrochemical techniques, scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS) were used in this study to show how the corrosion mechanism of several commercial grades of stainless steel in hot caustic solution is strongly influenced by the presence of sodium sulfide. Experimental results from super ferritic stainless steel UNS S44660 (26Cr-3Ni-3Mo) were compared to austenitic stainless steel UNS S31603, lean duplex stainless steel (DSS) UNS S32101, and standard DSS UNS S32205 in caustic solution, with and without sodium sulfide, at 443 K (170 °C). Weight loss measurements indicated that corrosion rates of UNS44660 were much lower than the other grades of stainless steel in the presence of the sodium sulfide. Potentiodynamic polarization and linear polarization resistance measurements showed that the electrochemical behavior was altered by the adhesion of sulfur species, which reduced the polarization resistances and increased the anodic current densities. SEM and XPS results imply that the surface films that formed in caustic solution containing sodium sulfide were defective due to the adsorption of sulfide, which destabilized the passive film and led to the formation of insoluble metal sulfide compounds.

  17. Effect of cold deformation on pitting corrosion of 00Cr18Mn15Mo2N0.86 stainless steel for coronary stent application.

    PubMed

    Ren, Yibin; Zhao, Haochuan; Liu, Wenpeng; Yang, Ke

    2016-03-01

    The high nitrogen nickel-free stainless steel has offered an alternative to further improve the performance of the coronary stents, and simultaneously avoids the potential harms of nickel element. Both cold deformation and pitting corrosion are very important for coronary stents made of stainless steel. In this work, the effect of cold deformation on the pitting corrosion resistance of a high nitrogen nickel-free stainless steel (00Cr18Mn15Mo2N0.86) in 0.9% saline solution was investigated. The results showed that the pitting corrosion of the steel was nearly unchanged with increases of the cold deformation up to 50%, indicating that the higher nitrogen content can reduce the negative effect of cold deformation on the pitting corrosion resistance, which is beneficial for the long term service of coronary stents in blood vessel. PMID:26706533

  18. The effect of chloride ions on the corroded surface layer of 00Cr22Ni5Mo3N duplex stainless steel under cavitation.

    PubMed

    Wan, Tong; Xiao, Ning; Shen, Hanjie; Yong, Xingyue

    2016-11-01

    The effects of Cl(-) on the corroded surface layer of 00Cr22Ni5Mo3N duplex stainless steel under cavitation in chloride solutions were investigated using nanoindentation in conjunction with XRD and XPS. The results demonstrate that Cl(-) had a strong effect on the nano-mechanical properties of the corroded surface layer under cavitation, and there was a threshold Cl(-) concentration. Furthermore, a close relationship between the nano-mechanical properties and the cavitation corrosion resistance of 00Cr22Ni5Mo3N duplex stainless steel was observed. The degradation of the nano-mechanical properties of the corroded surface layer was accelerated by the synergistic effect between cavitation erosion and corrosion. A key factor was the adsorption of Cl(-), which caused a preferential dissolution of the ferrous oxides in the passive film layer on the corroded surface layer. Cavitation further promoted the preferential dissolution of the ferrous oxides in the passive film layer. Simultaneously, cavitation accelerated the erosion of the ferrite in the corroded surface layer, resulting in the degradation of the nano-mechanical properties of the corroded surface layer on 00Cr22Ni5Mo3N duplex stainless steel under cavitation. PMID:27245950

  19. Modeling of Crevice Corrosion Stability of a NiCrMo Alloy and Stainless Steel

    SciTech Connect

    F.J. Presuel-Moreno; F. Bocher; J.R. Scully; R.G. Kelly

    2006-05-19

    Damage of structural significance from crevice corrosion of corrosion resistant alloys requires that at least a portion of the creviced area remain active over a sufficiently long period. Stifling results shen the aggressive chemistry required inside the crevice to keep the material depassivated, i.e., actively corroding, cannot be maintained. This loss of critical chemistry occurs when the rate of mass transport out of the crevice exceeds the rate of dissolution and subsequent hydrolysis of metal ions inside the crevice. For the treatment considered here, the mass transport conditions are constant for a given geometry and potential. What then controls the stability of the internal chemistry is the interaction between the electrochemical kinetics at the interface and the crevice chemistry composition. This work focuses on the parameters that control the stability of crevice corrosion by modeling the evolution of the chemical and electrochemical conditions within a crevice open only at one end (e.g. the mouth) in which the entire crevice is initially filled with the Critical Chemistry Solution (CCS) or filled with chemistries slightly less or more aggressive than the CCS. The crevice mouth is in contact with a weak acid solution (pH 3) that provides the boundary conditions at the crevice mouth. The potential at the mouth was held constant at +0.1 V{sub sce} in most instances with selected cases held at 0.0 V{sub sce}. The material selected was Ni-22Cr-6Mo alloy. The electrochemical kinetics at the pH values of interest have been recently characterized via potentiodynamic polarization. Figure 1 shows the polarization curves for Ni-22Cr-6Mo samples tested at room temperature in various HCl solutions. These data were used in all calculations. That is as the pH changed, a new polarization curve was applied to the position in the crevice. E, pH was calculated at each position and from this data, current at each position was determined. The effects of the crevice gap and

  20. Electrochemical investigations of Cr-Ni-Mo stainless steel used in urology

    NASA Astrophysics Data System (ADS)

    Przondziono, J.; Walke, W.

    2011-05-01

    The influence of chemical passivation process on physical and chemical characteristics of samples made of X2CrNiMo 17-7-2 steel with differentiated hardening, in the solution simulating the environment of human urine was analysed in the study. Wire obtained in cold drawing process is used for the production of stents and appliances in urological treatment. Proper roughness of the surface was obtained through mechanical working - grinding (Ra = 0,40 μn) and electrochemical polishing (Ra = 0,12 μn). Chemical passivation process was carried out in 40% solution of HN03 within 60 minutes in the temperature of 65°C. The tests of corrosion resistance were made on the ground of registered anodic polarisation curves and Stern method. For evaluation of phenomena occurring on the surface of tested steel, electrochemical impedance spectroscopy (EIS) was applied.

  1. Tensile Properties of 17-7 PH and 12 MoV Stainless-Steel Sheet under Rapid-Heating and Constant-Temperature Conditions

    NASA Technical Reports Server (NTRS)

    Manning, Charles R., Jr.; Price, Howard L.

    1961-01-01

    Results are presented of rapid-heating tests of 17-7 PH and 12 MoV stainless-steel sheet heated to failure at temperature rates from about 1 F to 170 F per second under constant-load conditions. Yield and rupture strengths obtained from rapid-heating tests are compared with yield and tensile strengths obtained from short-time elevated-temperature tensile tests (30-minute exposure). A rate-temperature parameter was used to construct master curves from which yield and rupture stresses or temperatures can be predicted. A method for measuring strain by optical means is described.

  2. Stress corrosion cracking evaluation of martensitic precipitation hardening stainless steels

    NASA Technical Reports Server (NTRS)

    Humphries, T. S.; Nelson, E. E.

    1980-01-01

    The resistance of the martensitic precipitation hardening stainless steels PH13-8Mo, 15-5PH, and 17-4PH to stress corrosion cracking was investigated. Round tensile and c-ring type specimens taken from several heats of the three alloys were stressed up to 100 percent of their yield strengths and exposed to alternate immersion in salt water, to salt spray, and to a seacoast environment. The results indicate that 15-5PH is highly resistant to stress corrosion cracking in conditions H1000 and H1050 and is moderately resistant in condition H900. The stress corrosion cracking resistance of PH13-8Mo and 17-4PH stainless steels in conditions H1000 and H1050 was sensitive to mill heats and ranged from low to high among the several heats included in the tests. Based on a comparison with data from seacoast environmental tests, it is apparent that alternate immersion in 3.5 percent salt water is not a suitable medium for accelerated stress corrosion testing of these pH stainless steels.

  3. Effect of micro-alloy elements (Ti, Nb, Al and Ca) on corrosion resistance of 26%Cr-2%Mo stainless steel in chloride solutions

    SciTech Connect

    Kim, H.; Lee, Y.D.

    1999-11-01

    Ferritic stainless steels have higher corrosion and stress corrosion cracking resistance in chloride environments than austenitic stainless steels. The production mat of ferritic stainless steels is lower than austenitic stainless steels. However, the application of highly alloyed ferritic stainless steels is limited due to low toughness and intergranular corrosion attack. Corrosion resistance of 26%Cr-2%Mo ferritic steels was evaluated using polarization test in 20% NaCl solution and the ferric chloride test. In addition, TEM and SEM were employed to analyze the secondary phases around the matrix where pitting corrosion occurred. In ferric chloride test the crevice corrosion resistance of non-stabilized alloy and Ca added alloy was lower than that of stabilized alloy and the crevice corrosion resistance of stabilized alloys was independent of stabilizing element such as Ti and Nb. The pitting corrosion resistance in chloride solution depended on micro-alloying elements as well as the surface treatment such as pickling and polishing. The effect of micro-alloy element and surface treatment on corrosion properties was explained with the aid of SEM observations. Among the polished alloys, the addition of Nb was the most effective for pitting corrosion resistance but the addition of Ti or Ca decreased the corrosion resistance. The pickling increased the corrosion resistance in all alloys except alloy No. 4 (Ti + Nb + Al). Pickling effectively increased corrosion resistance of the alloy containing Ti or Ca, due to removal of pit initiation sites associated with TiN inclusions or unstable phase (i.e., CaS, TiN).

  4. Effect of Decarburization on Notch Sensitivity and Fatigue-Crack-Propagation Rates in 12 MoV Stainless-Steel Sheet

    NASA Technical Reports Server (NTRS)

    Herrnstein, William H., III; McEvily, Arthur J., Jr.

    1961-01-01

    Tests were conducted in order to determine the effect of surface decarburization on the notch sensitivity and rate of fatigue crack propagation in 12 MoV stainless-steel sheet at room temperature. Three specimen configurations were utilized in the course of the investigation: standard tensile specimen, 9-inch-wide specimens containing fatigue cracks or thread-cut notches of 0.005-inch radius, and 2-inch-wide specimens containing fatigue cracks. The 12 MoV stainless-steel sheet in the normal condition was found to have an ultimate tensile strength of 251 ksi and to be extremely notch sensitive. The material in the decarburized condition was found to have an ultimate tensile strength of 210 ksi and to be considerably stronger than the normal material in the presence of fatigue cracks. Decarburization did not appear to have any significant influence on the rate of fatigue crack propagation in the 2-inch-wide specimens at the stress levels considered. In addition to the tests, two methods for predicting residual static strength and their application to the material are discussed.

  5. Influence of Prior Fatigue Damage on Tensile Properties of 316L(N) Stainless Steel and Modified 9Cr-1Mo Steel

    NASA Astrophysics Data System (ADS)

    Mariappan, K.; Shankar, Vani; Sandhya, R.; Mathew, M. D.; Bhaduri, A. K.

    2015-02-01

    In the current study, the effect of prior low-cycle fatigue (LCF) damage on the tensile properties of 316L(N) stainless steel (SS) and modified 9Cr-1Mo steel were systematically investigated. The LCF tests were interrupted at 5, 10, 30, and 50 pct of the total fatigue life followed by tensile tests on the same specimens at the same strain rate (3 × 10-3 s-1) and temperatures of 300 K, 823 K, and 873 K (27 °C, 550 °C, and 600 °C). Prior strain cycling at elevated temperatures had remarkable effect on the tensile properties of both cyclically hardening and cyclically softening materials. An exponential relationship between the yield stress and the amount of pre-strain cycles is obtained for both the materials. The initial drastic change in the yield strength values up to 10 pct of fatigue life may be due to the microstructural changes that lead to hardening or softening in 316L(N) SS and modified 9Cr-1Mo steel, respectively. Saturation in the yield strength values beyond 10 pct of fatigue life has practical importance for remnant fatigue life assessment. Evolution of fatigue damage in both the 316L(N) SS and modified 9Cr-1Mo steel was analyzed using the surface replica technique.

  6. Effects of Ce, Y and Mo Addition on the Stress Accelerated Oxidation of Austenitic Stainless Steel in Oxygenated High Temperature Water

    SciTech Connect

    Shengchun Wang; Nobuaki Kawaguchi; Tetsuo Shoji

    2004-07-01

    Based upon the recent progress in mechanistic understanding of intergranular stress corrosion cracking (IGSCC) of austenitic stainless steels in high temperature water in light water reactor (LWR), the effects of Ce, Y, and Mo addition on oxidation kinetics under a tensile stress condition was investigated. Minor impurity of P was also studied. A kind of circumferentially notched tensile specimen was prepared to simulate the crack tip stress field. The notched specimens of different materials studied were applied with an almost constant load in simulated boiling water reactor (BWR) water. The oxidation was examined by the specimen cross section. It was shown that these elements have quite clear effects on the metal oxidation and alloying element distribution in the oxide layer. (authors)

  7. Lattice dynamics in austenitic stainless steels Fe 18Cr 12Ni 2Mo and Fe 18Cr 16Ni 10Mn

    NASA Astrophysics Data System (ADS)

    Rajevac, V.; Hoelzel, M.; Danilkin, S. A.; Hoser, A.; Fuess, H.

    2004-04-01

    Phonon dispersion curves of austenitic stainless steels Fe-18Cr-16Ni-10Mn and Fe-18Cr-12Ni-2Mo have been measured by triple-axis neutron spectroscopy. The data were analysed using Born-von Karman interactions as well as calculations including the contribution of conduction electrons on the lattice dynamics. An appropriate description of the experimental data was obtained by taking into account two-neighbour shells plus the contribution of the electron gas. The elastic constants and moduli obtained are close to reported results by ultrasonic studies on polycrystalline samples. The phonon densities of states in both systems calculated from the dispersion curves agree well with results obtained by time-of-flight neutron spectroscopy on polycrystalline samples. The Debye temperature THgr(T) shows a minimum around 40 K, similar to copper and nickel.

  8. Quasicrystalline and crystalline precipitation during isothermal tempering in a 12Cr-9Ni-4Mo maraging stainless steel

    SciTech Connect

    Liu, P.; Stigenberg, A.H.; Nilsson, J.O.

    1995-07-01

    A thorough microstructural investigation has been performed on a high strength maraging steel of the type 12%Cr-9%Ni-4%Mo-2%Cu-1%Ti. The major precipitate formed during isothermal aging at 475 C is a quasicrystalline phase possessing icosahedral symmetry termed R{prime}-phase with a typical chemical composition of 48%Mo-33%Fe-13%Cr-2%Ni-4%Si. At 550 C the major precipitate is trigonal R-phase with a typical composition of 45%Mo-31%Fe-18%Cr-4%Ni-2%Si. At 550 C also Laves phase with a composition of 48%Mo-35%Fe-13%Cr-2%Ni-2%Si could be observed. At both 475 and 550 C an ordered phase termed L-phase precipitated. This minority phase has an ordered face centered cubic (f.c.c.) structure of type L1{sub 0}. Its composition is typically 9%Fe-4%Cr-52%Ni-15%Mo.-16%Ti-4%Al. R{prime}-phase formed at 475 C transformed to R-phase and Laves phase during aging at 550 C. In an analogous manner, R-phase and Laves phase formed at 550 C transformed to R{prime}-phase during subsequent aging at 475 C. This transformation was rationalized by a strong similarity in crystal structure between quasicrystalline R{prime}-phase of icosahedral symmetry and Frank-Kasper phases such as R-phase and Laves phase.

  9. In Situ Thermo-magnetic Investigation of the Austenitic Phase During Tempering of a 13Cr6Ni2Mo Supermartensitic Stainless Steel

    NASA Astrophysics Data System (ADS)

    Bojack, A.; Zhao, L.; Morris, P. F.; Sietsma, J.

    2014-09-01

    The formation of austenite during tempering of a 13Cr6Ni2Mo supermartensitic stainless steel (X2CrNiMoV13-5-2) was investigated using an in situ thermo-magnetic technique to establish the kinetics of the martensite to austenite transformation and the stability of austenite. The austenite fraction was obtained from in situ magnetization measurements. It was found that during heating to the tempering temperature 1 to 2 vol pct of austenite, retained during quenching after the austenitization treatment, decomposed between 623 K and 753 K (350 °C and 480 °C). The activation energy for martensite to austenite transformation was found by JMAK-fitting to be 233 kJ/mol. This value is similar to the activation energy for Ni and Mn diffusion in iron and supports the assumption that partitioning of Ni and Mn to austenite are mainly rate determining for the austenite formation during tempering. This also indicates that the stability of austenite during cooling after tempering depends on these elements. With increasing tempering temperature the thermal stability of austenite is decreasing due to the lower concentrations of austenite-stabilizing elements in the increased fraction of austenite. After cooling from the tempering temperature the retained austenite was further partially decomposed during holding at room temperature. This appears to be related to previous martensite formation during cooling.

  10. In Situ Thermo-magnetic Investigation of the Austenitic Phase During Tempering of a 13Cr6Ni2Mo Supermartensitic Stainless Steel

    NASA Astrophysics Data System (ADS)

    Bojack, A.; Zhao, L.; Morris, P. F.; Sietsma, J.

    2014-12-01

    The formation of austenite during tempering of a 13Cr6Ni2Mo supermartensitic stainless steel (X2CrNiMoV13-5-2) was investigated using an in situ thermo-magnetic technique to establish the kinetics of the martensite to austenite transformation and the stability of austenite. The austenite fraction was obtained from in situ magnetization measurements. It was found that during heating to the tempering temperature 1 to 2 vol pct of austenite, retained during quenching after the austenitization treatment, decomposed between 623 K and 753 K (350 °C and 480 °C). The activation energy for martensite to austenite transformation was found by JMAK-fitting to be 233 kJ/mol. This value is similar to the activation energy for Ni and Mn diffusion in iron and supports the assumption that partitioning of Ni and Mn to austenite are mainly rate determining for the austenite formation during tempering. This also indicates that the stability of austenite during cooling after tempering depends on these elements. With increasing tempering temperature the thermal stability of austenite is decreasing due to the lower concentrations of austenite-stabilizing elements in the increased fraction of austenite. After cooling from the tempering temperature the retained austenite was further partially decomposed during holding at room temperature. This appears to be related to previous martensite formation during cooling.

  11. Boundary lubrication of stainless steel and CoCrMo alloy based on phosphorous and boron compounds in oil-in-water emulsion

    NASA Astrophysics Data System (ADS)

    Yan, Jincan; Zeng, Xiangqiong; Ren, Tianhui; van der Heide, Emile

    2014-10-01

    Emulsion lubrication is widely used in metal forming operations and has potential applications in the biomedical field, yet the emulsion lubrication mechanism is not well understood. This work explores the possibilities of three different oil-in-water (O/W) emulsions containing dibutyl octadecylphosphoramidate (DBOP), 6-octadecyl-1,3,6,2-dioxazaborocan-2-ol calcium salt (ODOC) and 2-(4-dodecylphenoxy)-6-octadecyl-1,3,6,2-dioxazaborocane (DOB) to generate boundary films on stainless steel AISI 316 and CoCrMo alloy surfaces. Experimental results show lower friction values for the emulsions in combination with CoCrMo compared to AISI 316. The different performance of the additives is related to the composition of the adsorption and reaction film on the interacting surfaces, which was shown to be dependent on the active elements and molecular structure of the additives. The friction profile of the emulsions indicates that the emulsion appears to be broken during the rubbing process, then the additives adsorb onto the metal surface to form protecting boundary layers. The XPS analysis shows that for boundary lubrication conditions, the additive molecules in the emulsion first adsorb on the metal surface after the droplet is broken, and then decompose and react with the metal surface during the rubbing process to form stable lubricating films on the rubbed surfaces.

  12. Isothermal martensitic transformation in a 12Cr-9Ni-4Mo-2Cu stainless steel in applied magnetic fields

    NASA Astrophysics Data System (ADS)

    San Martín, D.; Aarts, K. W. P.; Rivera-Díaz-del-Castillo, P. E. J.; van Dijk, N. H.; Brück, E.; van der Zwaag, S.

    This work concerns an in situ study of the isothermal formation of martensite in a stainless steel under the influence of magnetic fields up to 9 T at three different temperatures (213, 233 and 253 K). It is shown that the presence of a constant applied magnetic field promotes the formation of martensite significantly. The activation energy for the nucleation of martensite has been derived using a semi-empirical kinetic model. The experimental results have been analyzed using the Ghosh and Olson model. While this model describes the time and field dependences of the experimental data well, the thermal frictional energy and the defect size values are much lower than those expected from earlier work.

  13. Coupled Multi-Electrode Investigation of Crevice Corrosion of 316 Stainless Steel and NiCrMo Alloy 625

    SciTech Connect

    F. Bocher; F.J. Presuel-Moreno; J.R. Scully

    2006-06-08

    the position where the potential drops to E{sub Flade}. Figure 1 illustrates the resulting x{sub crit} vs. G scaling laws for 316 Stainless Steel in 1 M HCl at 50 C. The coupled multi-wire array is composed of one hundred identical 316 Stainless Steel wires in a five by twenty formation inserted in a groove of a 316 Stainless Steel rod such that the ends of the wires are flush mounted with the rod. The 100 wires are coupled electrically through in-line zero resistance ammeters. The diameter of the wires (250 {micro}m) was chosen so that x{sub crit} (critical initiation distance from the crevice mouth) and the expected zone of crevice corrosion (predicted from the scaling law) would be larger than the radius of a single wire. The array created a flush mounted planar electrode with the surface/volume ratio obtained in planar crevices. The observation of the current evolution as a function of position inside and outside the crevice as function of time was made possible as illustrated in Figure 2 in 0.6 M NaCl at 50 C.

  14. Effect of Laves Phase on High-Temperature Deformation and Microstructure Evolution in an 18Cr-2Mo-0.5Nb Ferritic Stainless Steel

    NASA Astrophysics Data System (ADS)

    Ikeda, Ken-ichi; Yamoah, Nana Kwame Gyan; Reynolds, William T.; Hamada, Jun-ichi; Murayama, Mitsuhiro

    2015-08-01

    Niobium-containing ferritic stainless steels are finding new applications in automotive exhaust components because of their oxidation resistance, thermal fatigue resistance, and high-temperature strength. The mechanical behavior of Nb-containing ferritic steels at service temperatures of 973 K (700 °C) and higher results from the convolution of dynamic microstructural changes including precipitation, precipitate coarsening, strain hardening, recovery, and recrystallization. The relative contributions of these competing processes have yet to be clarified. In this study, the high-temperature flow strength of an 18Cr-2Mo-0.5Nb ferritic stainless steel (SUS 444) was correlated with microstructure under different strain and initial precipitate distributions to clarify the relative role of the strengthening and softening processes. High-temperature tensile tests at 1023 K (750 °C) of un-aged (initial microstructure is precipitate-free) and pre-aged (initial microstructure contains precipitates) samples were carried out and transmission electron microscopy was used to assess dislocation distributions and precipitate morphology. The difference in the stress-strain curves between un-aged and pre-aged samples was drastic; the yield strength of the un-aged sample was twice that of the pre-aged sample, and the un-aged sample exhibits a noticeable yield drop. Transmission electron microscopy revealed a Laves phase nucleated and grew during the high-temperature tensile test in the un-aged sample and the majority of the precipitates in the pre-aged sample were the same Laves phase. Furthermore, a strain effect on precipitate growth was recognized in un-aged and pre-aged conditions by comparing grip (no strain) and gage (strained) sections of tensile samples. The dominant strengthening contribution in un-aged samples is initially the precipitate shearing mechanism and it changes to Orowan strengthening beyond the ultimate tensile strength, whereas the dominant contribution in

  15. Changes in Microstructural and Mechanical Properties of AISI Type 316LN Stainless Steel and Modified 9Cr-1Mo Steel on Long-Term Exposure to Flowing Sodium in a Bi-Metallic Sodium Loop

    NASA Astrophysics Data System (ADS)

    Sivai Bharasi, N.; Pujar, M. G.; Thyagarajan, K.; Mallika, C.; Kamachi Mudali, U.; Dhaul, Anuradha; Nandagopal, M.; Moitra, A.; Chandramouli, S.; Rajan, K. K.

    2015-12-01

    AISI Type 316LN stainless steel (SS) and modified 9Cr-1Mo steel were exposed to flowing sodium at 798 K (525 °C) for 30000 hours in a bi-metallic sodium loop. The changes in microchemical, microstructural, and mechanical properties were evaluated and compared with the as-received and thermally aged specimens. Effective carbon diffusion coefficient {( {D_{C}^{eff} } )} was calculated to be 6.8 × 10-19 m2/s. Depth of carburization analyzed by secondary ion mass spectroscopy technique was around 100 µm for sodium-exposed 316LN SS. Selective leaching of nickel occurred across depth from the surface of sodium-exposed 316LN SS with the formation of 10 µm ferrite layer, and it showed an increase in yield strength by 15 pct, reduction in ductility by 60 pct, and a decrease in impact energy by 15 pct vis-a-vis the as-received and thermally aged specimens. This reduction in ductility occurred due to extensive precipitation of sigma phase as a result of long-term thermal aging. No significant changes were observed in the sodium/modified 9Cr-1Mo steel interfacial microstructure as well as tensile properties of sodium-exposed modified 9Cr-1Mo steel. Although modified 9Cr-1Mo neither showed carburization nor decarburization on sodium exposure, it showed a drastic reduction in the impact strength, which was attributed to the presence of Laves phase, observed in X-ray diffraction patterns.

  16. Surface modification of superaustenitic and maraging stainless steels by low-temperature gas-phase carburization

    NASA Astrophysics Data System (ADS)

    Gentil, Johannes

    Low-temperature gas-phase carburization of 316L austenitic stainless steel was developed in recent years by the Swagelok company. This process generates great mechanical and electrochemical surface properties. Hardness, wear resistance, fatigue behavior, and corrosion resistance are dramatically improved, while the formation of carbides is effectively suppressed. This new technique is of technical, economical, but especially of scientific interest because the surface properties of common stainless steel can be enhanced to a level of more sophisticated and more expensive superalloys. The consequential continuation of previous research is the application of the carburization process to other steel grades. Differences in chemical composition, microstructure, and passivity between the various alloys may cause technical problems and it is expected that the initial process needs to be optimized for every specific material. This study presents results of low-temperature carburization of AL-6XN (superaustenitic stainless steel) and PH13-8Mo (precipitation-hardened martensitic stainless steel). Both alloys have been treated successfully in terms of creating a hardened surface by introducing high amounts of interstitially dissolved carbon. The surface hardness of AL-6XN was increased to 12GPa and is correlated with a colossal carbon supersaturation at the surface of up to 20 at.%. The hardened case develops a carburization time-dependent thickness between 10mum after one carburization cycle and up to 35mum after four treatments and remains highly ductile. Substantial broadening of X-ray diffraction peaks in low-temperature carburized superaustenitic stainless steels are attributed to the generation of very large compressive biaxial residual stresses. Those large stresses presumably cause relaxations of the surface, so-called undulations. Heavily expanded regions of carburized AL-6XN turn ferromagnetic. Non-carburized AL-6XN is known for its outstanding corrosion resistance

  17. Influence of volumic heat treatments upon cavitation erosion resistance of duplex X2CrNiMoN 22-5-3 stainless steels

    NASA Astrophysics Data System (ADS)

    Micu, L. M.; Bordeasu, I.; Popoviciu, M. O.; Popescu, M.; Bordeaşu, D.; Salcianu, L. C.

    2015-06-01

    The stainless steels Duplex 2205 with austenite and ferrite structure have mechanical characteristics close to those of martensite stainless steels but a better corrosion resistance; these steels are very sensitive on the heat treatments. Present work studies the cavitation erosion for those steels for three different heat treatments: simply quenched, annealed at 475°C post quenching and annealed at 875°C. The researches were undertaken at Timisoara “Politehnica” University in the Laboratory of Material Science and the Laboratory of Cavitation, using the T2 facility which integrally respects the recommendation of ASTM G32- 10 Standard. The best results were obtained with the specimens annealed at 875°C. In comparison with the stainless steel 41Cr4, with very good cavitation erosion qualities, all tested steels presented also good erosion resistance. So, Duplex 2205 steels can be used for details subjected to cavitation. The best results are obtained by increasing both the hardness and the quantity of the structure constituent with better cavitation erosion resistance, in our case the alloyed austenite.

  18. Duplex stainless steels for osteosynthesis devices.

    PubMed

    Cigada, A; Rondelli, G; Vicentini, B; Giacomazzi, M; Roos, A

    1989-09-01

    The austenitic stainless steels used today for the manufacture of osteosynthesis devices are sensitive to crevice corrosion. In this study the corrosion properties of some duplex stainless steels were evaluated and compared to traditional austenitic stainless steels. According to our results the following ranking was established: 23Cr-4Ni less than AISI 316L less than ASTM F138 less than 22Cr-5Ni-3Mo less than 27Cr-31Ni-3.5Mo less than 25Cr-7Ni-4Mo-N. In particular the results showed that the high-performance 25Cr-7Ni-4Mo-N duplex stainless steel, with high molybdenum and nitrogen contents, can be considered not susceptible to crevice corrosion in the human body. The duplex stainless steels have also better mechanical properties at the same degree of cold working compared with austenitic stainless steels. Hence the 25Cr-7Ni-4Mo-N duplex stainless steel can be considered a convenient substitute of ASTM F138 for orthopedic and osteosynthesis devices. PMID:2777835

  19. X-ray photoelectron spectroscopic analysis of oxidized Fe-16Cr-16Ni-2Mn-1Mo-2Si austenitic stainless steel

    SciTech Connect

    Poston, J.A., Jr.; Siriwardane, R.V.; Dunning, J.S.; Alman, D.E.; Rawers, J.C.

    2007-03-30

    Depth profile analysis (argon ion etching/X-ray photoelectron spectroscopy) was conducted on a series of Fe–16Cr–16Ni–2Mn–1Mo–2Si austenitic stainless steel samples oxidized at 973 and 1073 K with exposure times of 25, 100, 193, 436 and 700 h. Surface and near surface rearrangement following oxidation resulted in a region of high Cr concentration on all oxidized samples. Temperature and time dependence to O2 penetration depth was observed. In general, O2 penetration depth was found to increase with increasing exposure up to 436 h. No increase in depth was observed between 436 and 700 h exposure time.

  20. SCC of austenitic stainless steel, Ni-21Cr-13.5Mo alloy, and 0.3Mo-0.8Ni-Ti in 350 C synthetic, NO{sub 2}2-NO{sub 3}-OH tank waste

    SciTech Connect

    Pednekar, S.P.

    1998-12-31

    A necessary step in preparation of high-level radioactive tank waste for sate disposal is removal of non radioactive organic and inorganic components from washed waste. The oxidizing and alkaline nature of most wastes allows the removal of the organic components as water vapor, carbon dioxide, and ammonia gas merely by heating the wastes to no more than 350 C. Type 3 16L stainless steel (UNS S3 1603) a 21Cr-13.5Mo-Ni alloy (UNS N06022), and 0.8Ni-0.3Mo-Ti alloy (UNS R53400) were candidate materials for reactors in which the oxidation could be performed. Slow-strain-rate tests were performed on these three materials at a strain rate of 10{sup {minus}6}sec{sup {minus}1} in a diluted waste type solution containing 4.1% NO{sub 2}, 3.7% NO{sub 3}, 1% OH, and 0.22% TIC. All three materials showed intergranular stress corrosion cracking with substantial losses in ductility and strength.

  1. 15 CFR 13.8 - Opportunity to comment on proposed Federal financial assistance and direct Federal development.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 15 Commerce and Foreign Trade 1 2012-01-01 2012-01-01 false Opportunity to comment on proposed Federal financial assistance and direct Federal development. 13.8 Section 13.8 Commerce and Foreign Trade... ACTIVITIES § 13.8 Opportunity to comment on proposed Federal financial assistance and direct...

  2. 15 CFR 13.8 - Opportunity to comment on proposed Federal financial assistance and direct Federal development.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 15 Commerce and Foreign Trade 1 2013-01-01 2013-01-01 false Opportunity to comment on proposed Federal financial assistance and direct Federal development. 13.8 Section 13.8 Commerce and Foreign Trade... ACTIVITIES § 13.8 Opportunity to comment on proposed Federal financial assistance and direct...

  3. 15 CFR 13.8 - Opportunity to comment on proposed Federal financial assistance and direct Federal development.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 15 Commerce and Foreign Trade 1 2011-01-01 2011-01-01 false Opportunity to comment on proposed Federal financial assistance and direct Federal development. 13.8 Section 13.8 Commerce and Foreign Trade... ACTIVITIES § 13.8 Opportunity to comment on proposed Federal financial assistance and direct...

  4. 15 CFR 13.8 - Opportunity to comment on proposed Federal financial assistance and direct Federal development.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 15 Commerce and Foreign Trade 1 2014-01-01 2014-01-01 false Opportunity to comment on proposed Federal financial assistance and direct Federal development. 13.8 Section 13.8 Commerce and Foreign Trade... ACTIVITIES § 13.8 Opportunity to comment on proposed Federal financial assistance and direct...

  5. 15 CFR 13.8 - Opportunity to comment on proposed Federal financial assistance and direct Federal development.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Opportunity to comment on proposed Federal financial assistance and direct Federal development. 13.8 Section 13.8 Commerce and Foreign Trade Office of the Secretary of Commerce INTERGOVERNMENTAL REVIEW OF DEPARTMENT OF COMMERCE PROGRAMS AND ACTIVITIES § 13.8 Opportunity to comment...

  6. Duplex stainless steel—Microstructure and properties

    NASA Astrophysics Data System (ADS)

    Debold, Terry A.

    1989-03-01

    Literature describing the microstructure of austenitic-ferritic stainless steels is reviewed, including phases which can be deleterious, such as σ and ά. The mechanical properties and corrosion resistance of Carpenter Technology's 7-Mo PLUSsr stainless (UNS S32950) demonstrate the resistance of this material to the formation of these phases and their deleterious effects. This material was evaluated in the annealed and welded conditions and after extended thermal treatments to simulate boiler and pressure vessel service.

  7. Nano-composite stainless steel

    DOEpatents

    Dehoff, Ryan R.; Blue, Craig A.; Peter, William H.; Chen, Wei; Aprigliano, Louis F.

    2015-07-14

    A composite stainless steel composition is composed essentially of, in terms of wt. % ranges: 25 to 28 Cr; 11 to 13 Ni; 7 to 8 W; 3.5 to 4 Mo; 3 to 3.5 B; 2 to 2.5 Mn; 1 to 1.5 Si; 0.3 to 1.7 C; up to 2 O; balance Fe. The composition has an austenitic matrix phase and a particulate, crystalline dispersed phase.

  8. 27. STAINLESS STEEL FERMENTING CASKS MADE BY ZERO MANG OF ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    27. STAINLESS STEEL FERMENTING CASKS MADE BY ZERO MANG OF WASHINGTON, MISSOURI. VIEW LOOKING NORTH TOWARD VAULT OF THE TWELVE APOSTLES - Stone Hill Winery, 401 West Twelfth Street, Hermann, Gasconade County, MO

  9. Heat-to-Heat Variation in Creep Life and Fundamental Creep Rupture Strength of 18Cr-8Ni, 18Cr-12Ni-Mo, 18Cr-10Ni-Ti, and 18Cr-12Ni-Nb Stainless Steels

    NASA Astrophysics Data System (ADS)

    Abe, Fujio

    2016-06-01

    Metallurgical factors causing the heat-to-heat variation in time to rupture have been investigated for 300 series stainless steels for boiler and heat exchanger seamless tubes, 18Cr-8Ni (JIS SUS 304HTB), 18Cr-12Ni-Mo (JIS SUS 316HTB), 18Cr-10Ni-Ti (JIS SUS321 HTB), and 18Cr-12Ni-Nb (JIS SUS 347HTB), at 873 K to 1023 K (600 °C to 750 °C) using creep rupture data for nine heats of the respective steels in the NIMS Creep Data Sheets. The maximum time to rupture was 222,705.3 hours. The heat-to-heat variation in time to rupture of the 304HTB and 316HTB becomes more significant with longer test durations at times above ~10,000 hours at 973 K (700 °C) and reaches to about an order of magnitude difference between the strongest and weakest heats at 100,000 hours, whereas that of the 321HTB and 347HTB is very large of about an order of magnitude difference from a short time of ~100 hours to long times exceeding 100,000 hours at 873 K to 973 K (600 °C to 700 °C). The heat-to-heat variation in time to rupture is mainly explained by the effect of impurities: Al and Ti for the 304HTB and 316HTB, which reduces the concentration of dissolved nitrogen available for the creep strength by the formation of AlN and TiN during creep, and boron for the 347HTB, which enhances fine distributions of M23C6 carbides along grain boundaries. The heat-to-heat variation in time to rupture of the 321HTB is caused by the heat-to-heat variation in grain size, which is inversely proportional to the concentration of Ti. The fundamental creep rupture strength not influenced by impurities is estimated for the steels. The 100,000 hours-fundamental creep rupture strength of the 347HTB steel is lower than that of 304HTB and 316HTB at 873 K and 923 K (600 °C and 650 °C) because the slope of stress vs time to rupture curves is steeper in the 347HTB than in the 304HTB and 316HTB. The 100,000 hours-fundamental creep rupture strength of the 321HTB exhibits large variation depending on grain size.

  10. Heat-to-Heat Variation in Creep Life and Fundamental Creep Rupture Strength of 18Cr-8Ni, 18Cr-12Ni-Mo, 18Cr-10Ni-Ti, and 18Cr-12Ni-Nb Stainless Steels

    NASA Astrophysics Data System (ADS)

    Abe, Fujio

    2016-09-01

    Metallurgical factors causing the heat-to-heat variation in time to rupture have been investigated for 300 series stainless steels for boiler and heat exchanger seamless tubes, 18Cr-8Ni (JIS SUS 304HTB), 18Cr-12Ni-Mo (JIS SUS 316HTB), 18Cr-10Ni-Ti (JIS SUS321 HTB), and 18Cr-12Ni-Nb (JIS SUS 347HTB), at 873 K to 1023 K (600 °C to 750 °C) using creep rupture data for nine heats of the respective steels in the NIMS Creep Data Sheets. The maximum time to rupture was 222,705.3 hours. The heat-to-heat variation in time to rupture of the 304HTB and 316HTB becomes more significant with longer test durations at times above ~10,000 hours at 973 K (700 °C) and reaches to about an order of magnitude difference between the strongest and weakest heats at 100,000 hours, whereas that of the 321HTB and 347HTB is very large of about an order of magnitude difference from a short time of ~100 hours to long times exceeding 100,000 hours at 873 K to 973 K (600 °C to 700 °C). The heat-to-heat variation in time to rupture is mainly explained by the effect of impurities: Al and Ti for the 304HTB and 316HTB, which reduces the concentration of dissolved nitrogen available for the creep strength by the formation of AlN and TiN during creep, and boron for the 347HTB, which enhances fine distributions of M23C6 carbides along grain boundaries. The heat-to-heat variation in time to rupture of the 321HTB is caused by the heat-to-heat variation in grain size, which is inversely proportional to the concentration of Ti. The fundamental creep rupture strength not influenced by impurities is estimated for the steels. The 100,000 hours-fundamental creep rupture strength of the 347HTB steel is lower than that of 304HTB and 316HTB at 873 K and 923 K (600 °C and 650 °C) because the slope of stress vs time to rupture curves is steeper in the 347HTB than in the 304HTB and 316HTB. The 100,000 hours-fundamental creep rupture strength of the 321HTB exhibits large variation depending on grain size.

  11. Tensile-property characterization of thermally aged cast stainless steels.

    SciTech Connect

    Michaud, W. F.; Toben, P. T.; Soppet, W. K.; Chopra, O. K.; Energy Technology

    1994-03-03

    The effect of thermal aging on tensile properties of cast stainless steels during service in light water reactors has been evaluated. Tensile data for several experimental and commercial heats of cast stainless steels are presented. Thermal aging increases the tensile strength of these steels. The high-C Mo-bearing CF-8M steels are more susceptible to thermal aging than the Mo-free CF-3 or CF-8 steels. A procedure and correlations are presented for predicting the change in tensile flow and yield stresses and engineering stress-vs.-strain curve of cast stainless steel as a function of time and temperature of service. The tensile properties of aged cast stainless steel are estimated from known material information, i.e., chemical composition and the initial tensile strength of the steel. The correlations described in this report may be used for assessing thermal embrittlement of cast stainless steel components.

  12. Tensile-property characterization of thermally aged cast stainless steels

    SciTech Connect

    Michaud, W.F.; Toben, P.T.; Soppet, W.K.; Chopra, O.K.

    1994-02-01

    The effect of thermal aging on tensile properties of cast stainless steels during service in light water reactors has been evaluated. Tensile data for several experimental and commercial heats of cast stainless steels are presented. Thermal aging increases the tensile strength of these steels. The high-C Mo-bearing CF-8M steels are more susceptible to thermal aging than the Mo-free CF-3 or CF-8 steels. A procedure and correlations are presented for predicting the change in tensile flow and yield stresses and engineering stress-vs.-strain curve of cast stainless steel as a function of time and temperature of service. The tensile properties of aged cast stainless steel are estimated from known material information, i.e., chemical composition and the initial tensile strength of the steel. The correlations described in this report may be used for assessing thermal embrittlement of cast stainless steel components.

  13. Is stainless steel really "stainless"?

    PubMed

    Porteous, Joan

    2011-06-01

    Initial purchase and replacement costs for surgical instrumentation are significant components in today's operating room budgets. OR staff and medical device reprocessing personnel work together as a team to ensure effective management of this valuable commodity. The purpose of this article is to discuss the composition of stainless steel surgical instruments, to identify processes to minimize damage to instruments caused by staining, corrosion, and pitting, and to utilize that information to describe effective measures to manage instrumentation in both the OR and reprocessing areas. PMID:21823503

  14. Processing, Microstructure, and Properties of Multiphase Mo Silicide Alloys

    SciTech Connect

    Heatherly, L.; Liu, C.T.; Schneibel, J.H.

    1998-11-30

    Multiphase Mo silicide alloys containing T2 (Mo{sub 5}SiB{sub 2}), Mo{sub 3}Si and Mo phases where prepared by both melting and casting (M and C) and powder metallurgical (PM) processes. Glassy phases are observed in PM materials but not in M and C materials. Microstructural studies indicate that the primary phase is Mo-rich solid solution in alloys containing {le}(9.4Si+13.8B, at. %) and T2 in alloys with {ge}(9.8Si+14.6B). An eutectic composition is estimated to be close to Mo-9.6Si-14.2B. The mechanical properties of multiphase silicide alloys were determined by hardness, tensile and bending tests at room temperature. The multiphase alloy MSB-18 (Mo-9.4Si-13.8B) possesses a flexure strength distinctly higher than that of MoSi{sub 2} and other Mo{sub 5}Si{sub 3} silicide alloys containing no Mo particles. Also, MSB-18 is tougher than MoSi{sub 2} by a factor of 4.

  15. Processing, microstructure, and properties of multiphase Mo silicide alloys

    SciTech Connect

    Liu, C.T.; Schneibel, J.H.; Heatherly, L.

    1999-07-01

    Multiphase Mo silicide alloys containing T2 (Mo{sub 5}SiB{sub 2}), Mo{sub 3}Si and Mo phases were prepared by both melting and casting (M and C) and powder metallurgical (PM) processes. Glassy phases are observed in PM materials but not in M and C materials. Microstructural studies indicate that the primary phase is Mo-rich solid solution in alloys containing {le}(9.4Si+13.8B, at.%) and T2 in alloys with {ge}(9.8Si+14.6B). An eutectic composition is estimated to be close to Mo-9.6Si-14.2B. The mechanical properties of multiphase silicide alloys were determined by hardness, tensile and bending tests at room temperature. The multiphase alloy MSB-18 (Mo-9.4Si-13.8B) possesses a flexure strength distinctly higher than that of MoSi{sub 2} and other Mo{sub 5}Si{sub 3} silicide alloys containing no Mo particles. Also, MSB-18 is tougher than MoSi{sub 2} by a factor of 4.

  16. Weld microstructure development and properties of precipitation-strengthened martensitic stainless steels

    SciTech Connect

    Brooks, J.

    1994-12-31

    Precipitation-strengthened martensitic stainless steels provide excellent strength (170--220 ksi Y.S.) with high corrosion resistance. However, upon aging, a large reduction in toughness may also occur. The gas tungsten arc (GTA) cold wire feed process was used to weld half inch thick plates of PH 13-8 Mo and Custom 450 from which both tensile and Charpy specimens were machined. A fundamental understanding of the details of weld microstructural evolution was developed by liquid tin quenching GTA welds in which the solidification behavior, primary phase of solidification, microsegregation, and solid-state transformations could be followed. For both alloys studied, the as-welded yield strengths were similar to those of the unaged base material, 130 ksi. Weld properties were very similar to those of the base materials for both alloy systems. Weld strength increases significantly upon aging and achieves a maximum at intermediate aging temperatures. The increase in strength is accompanied by a large decrease in Charpy impact energy; however, the minimum in toughness occurs at aging temperatures slightly less than those resulting in peak strengths. The evolution of the weld microstructure was found to support predictions of microstructural modeling. Although a high degree of alloying partitioning occurs during solidification, a large degree of homogenization occurs upon further solidification and cooling as a result of solid-state diffusion.

  17. In vivo behavior of a high performance duplex stainless steel.

    PubMed

    Cigada, A; De Santis, G; Gatti, A M; Roos, A; Zaffe, D

    1993-01-01

    An in vivo investigation of a new high molybdenum and nitrogen duplex stainless steel (25Cr--7Ni--4Mo--0.3N) has been performed. Cylindrical pins and specially developed devices, to test in static conditions the in vivo localized corrosion resistance, made of this new duplex steel and of a common austenitic stainless steel were implanted in rabbit's femurs for 6 and 12 months. After sacrifice, SEM observations and EDS microanalyses to detect metallic ion release were carried out on the femur sections surrounding the pins. Morphologic observations with stereoscope and SEM were performed on the metallic surfaces of the special devices in order to detect the presence of localized corrosion. Both ion release and localized corrosion were observed for the specimens made of austenitic stainless steel, but not for those made of 25Cr--7Ni--4Mo--0.3N duplex stainless steel. PMID:10148344

  18. Tensile properties of the modified 13Cr martensitic stainless steels

    NASA Astrophysics Data System (ADS)

    Mabruri, Efendi; Anwar, Moch. Syaiful; Prifiharni, Siska; Romijarso, Toni B.; Adjiantoro, Bintang

    2016-04-01

    This paper reports the influence of Mo and Ni on the tensile properties of the modified 13Cr martensitic stainless steels in tempered condition. Four steels with different content of Mo and Ni were prepared by induction melting followed by hot forging, quenching and tempering. The experimental results showed that the addition of about 1% and 3% Mo has a beneficial effect to increase both the tensile strength and the elongation of the steels. On the contrary, the addition of about 3% Ni into the martensitic stainless steel results in decreasing of both the tensile strength and the elongation. Among the alloys investigated the 13Cr3Mo type steel exhibited largest tensile strength of 1348 MPa and largest elongation of 12%. The observation on the tensile fractured surfaces by using scanning electron microscope supported these findings.

  19. Genome sequence of the flexirubin-pigmented soil bacterium Niabella soli type strain (JS13-8T)

    SciTech Connect

    Anderson, Iain; Munk, Christine; Lapidus, Alla L.; Nolan, Matt; Lucas, Susan; Tice, Hope; Glavina Del Rio, Tijana; Cheng, Jan-Fang; Han, Cliff; Tapia, Roxanne; Goodwin, Lynne A.; Pitluck, Sam; Liolios, Konstantinos; Mavromatis, K; Pagani, Ioanna; Mikhailova, Natalia; Pati, Amrita; Chen, Amy; Palaniappan, Krishna; Land, Miriam L; Rohde, Manfred; Tindall, Brian; Goker, Markus; Detter, J. Chris; Woyke, Tanja; Bristow, James; Eisen, Jonathan; Markowitz, Victor; Hugenholtz, Philip; Kyrpides, Nikos C; Klenk, Hans-Peter; Ivanova, N

    2012-01-01

    Niabella soli Weon et al. 2008 is a member of the Chitinophagaceae, a family within the class Sphingobacteriia that is poorly characterized at the genome level, thus far. N. soli strain JS13-8T is of interest for its ability to produce a variety of glycosyl hydrolases. The ge- nome of N. soli strain JS13-8T is only the second genome sequence of a type strain from the family Chitinophagaceae to be published, and the first one from the genus Niabella. Here we describe the features of this organism, together with the complete genome sequence and annotation. The 4,697,343 bp long chromosome with its 3,931 protein-coding and 49 RNA genes is a part of the Genomic Encyclopedia of Bacteria and Archaea project.

  20. Effect of Post-Weld Heat Treatment on Mechanical and Electrochemical Properties of Gas Metal Arc-Welded 316L (X2CrNiMo 17-13-2) Stainless Steel

    NASA Astrophysics Data System (ADS)

    Muhammad, F.; Ahmad, A.; Farooq, A.; Haider, W.

    2016-08-01

    In the present research work, corrosion behavior of post-weld heat-treated (PWHT) AISI 316L (X2CrNiMo 17-13-2) specimens joined by gas metal arc welding is compared with as-welded samples by using potentiodynamic polarization technique. Welded samples were PWHT at 1323 K for 480 s and quenched. Mechanical properties, corrosion behavior and microstructures of as-welded and PWHT specimens were investigated. Microstructural studies have shown grain size refinement after PWHT. Ultimate tensile strength and yield strength were found maximum for PWHT samples. Bend test have shown that PWHT imparted ductility in welded sample. Fractographic analysis has evidenced ductile behavior for samples. Potentiodynamic polarization test was carried out in a solution composed of 1 M H2SO4 and 1 N NaCl. Corrosion rate of weld region was 127.6 mpy, but after PWHT, it was decreased to 13.12 mpy.

  1. Experimental investigation of stress effect on swelling and microstructure of Fe-16Cr-15Ni-3Mo-Nb austenitic stainless steel under low-temperature irradiation up to high damage dose in the BOR-60 reactor

    NASA Astrophysics Data System (ADS)

    Neustroev, V. S.; Ostrovsky, Z. E.; Shamardin, V. K.

    2004-08-01

    The present paper was devoted to investigation of the stress effect on swelling and microstructure evolution of the Fe-15.8Cr-15.3Ni-2.8Mo-0.6Nb steel irradiated in the BOR-60 reactor at temperatures from 395 to 410 °C and damage doses from 79 to 98 dpa. Was found out that the stress increase leads to an increase of swelling, that can be associated with a decrease in incubation period with a practically constant swelling rate. Voids concentration increases at the first stage of irradiation when the void sizes are practically constant, and then the concentration reaches some saturation and swelling increase is caused by void growth.

  2. Corrosion of Stainless-Steel Tubing in a Spacecraft Launch Environment

    NASA Technical Reports Server (NTRS)

    Barile, Ronald G.; MacDowell, Louis G.; Curran, Joe; Calle, Luz Maria; Hodge, Timothy

    2001-01-01

    This is a report of exposure of various metal tubing to oceanfront launch environments. The objective is to examine various types of corrosion-resistant tubing for Space Shuttle launch sites. The metals were stainless steels (austenitic, low-carbon, Mo-alloy, superaustenitic, duplex, and superferritic), Ni-Cr-Mo alloy, Ni-Mo-Cr-Fe-W alloy, and austenitic Ni-base superalloy.

  3. Supertough Stainless Bearing Steel

    NASA Technical Reports Server (NTRS)

    Olson, Gregory B.

    1995-01-01

    Composition and processing of supertough stainless bearing steel designed with help of computer-aided thermodynamic modeling. Fracture toughness and hardness of steel exceeds those of other bearing steels like 440C stainless bearing steel. Developed for service in fuel and oxidizer turbopumps on Space Shuttle main engine. Because of strength and toughness, also proves useful in other applications like gears and surgical knives.

  4. Properties of super stainless steels for orthodontic applications.

    PubMed

    Oh, Keun-Taek; Kim, Young-Sik; Park, Yong-Soo; Kim, Kyoung-Nam

    2004-05-15

    Orthodontic stainless-steel appliances are considered to be corrosion resistant, but localized corrosion can occur in the oral cavity. This study was undertaken to evaluate the properties of super stainless steels in orthodontic applications. Accordingly, the metallurgical properties, mechanical properties, corrosion resistance, amount of the released nickel, cytotoxicity, and characteristics of the passive film were investigated. Corrosion resistances of the specimens were high and in the following order: super austenitic stainless steel (SR-50A) > super ferritic stainless steel (SFSS) = super duplex stainless steel (SR-6DX) > 316L SS > super martensitic stainless steel (SR-3Mo) in artificial saliva, 37 degrees C. At 500 mV (SCE), current densities of SR-50A, SFSS, SR-6DX, 316L SS, and SR-3Mo were 5.96 microA/cm(2), 20.3 microA/cm(2), 31.9 microA/cm(2), 805 microA/cm(2), and 5.36 mA/cm(2), respectively. Open circuit potentials of SR-50A, 316L SS, SR-6DX, SR-3Mo, and SFSS were - 0.2, - 0.22, - 0.24, - 0.43, and - 0.46 V (SCE), respectively. SR-50A, SFSS, and SR-6DX released below 3 ng/ml nickel for 8 weeks, and increased a little with immersion time, and 316L SS released about 3.5 ng/ml nickel, but SR-3Mo released a large amount of nickel, which increased with immersion time. The study demonstrated that SR-50A, SR-6DX, and SFSS have high corrosion resistance and mild or no cytotoxicity, due to the passive film enhanced by synergistic effect of Mo + N or by high addition effect of Cr + W. All super stainless steels showed very low cytotoxicity regardless of their nickel contents, although SR-3Mo was found to be relatively cytotoxic. From these studies, these steels are considered suitable for orthodontic applications. PMID:15116408

  5. Corrosion study of stainless steel SS304L in molten molybdates

    NASA Astrophysics Data System (ADS)

    Usami, T.; Uruga, K.; Tsukada, T.; Miura, Y.; Komamine, S.; Ochi, E.

    2016-04-01

    Depending on operating conditions of the vitrification process of high-level liquid waste, molten salt mainly composed of sodium and molybdenum can be generated, and poured into stainless steel canisters. In this work, the possible reaction between the molten molybdate and stainless steel was investigated using multi-component molybdate and simple Na2MoO4 - MoO3 molybdate. In the experiments using multi-component molybdates, no significant reaction is observed between the mixed molybdates and the stainless steel specimens at 700 °C in 4 h. The reaction rate of the stainless steel with the multi-component molybdate increases in proportion to exp(-1/T). The depth of the most reacted area is about 300 μm even at 1000 °C, and was much smaller than the 6 mm thickness of the canister. In the simple Na2MoO4 - MoO3 molybdate, the reaction rate was proportional to the MoO3 concentration. The essence of the reaction is oxidation of metals by Mo6+ - > Mo4+. Part of the reaction product mainly composed of Fe is dissolved into the molybdate, while the other part mainly composed of Cr sloughs and forms a banded layer.

  6. High Mn austenitic stainless steel

    DOEpatents

    Yamamoto, Yukinori [Oak Ridge, TN; Santella, Michael L [Knoxville, TN; Brady, Michael P [Oak Ridge, TN; Maziasz, Philip J [Oak Ridge, TN; Liu, Chain-tsuan [Knoxville, TN

    2010-07-13

    An austenitic stainless steel alloy includes, in weight percent: >4 to 15 Mn; 8 to 15 Ni; 14 to 16 Cr; 2.4 to 3 Al; 0.4 to 1 total of at least one of Nb and Ta; 0.05 to 0.2 C; 0.01 to 0.02 B; no more than 0.3 of combined Ti+V; up to 3 Mo; up to 3 Co; up to 1W; up to 3 Cu; up to 1 Si; up to 0.05 P; up to 1 total of at least one of Y, La, Ce, Hf, and Zr; less than 0.05 N; and base Fe, wherein the weight percent Fe is greater than the weight percent Ni, and wherein the alloy forms an external continuous scale including alumina, nanometer scale sized particles distributed throughout the microstructure, the particles including at least one of NbC and TaC, and a stable essentially single phase FCC austenitic matrix microstructure that is essentially delta-ferrite-free and essentially BCC-phase-free.

  7. Articles comprising ferritic stainless steels

    DOEpatents

    Rakowski, James M.

    2016-06-28

    An article of manufacture comprises a ferritic stainless steel that includes a near-surface region depleted of silicon relative to a remainder of the ferritic stainless steel. The article has a reduced tendency to form an electrically resistive silica layer including silicon derived from the steel when the article is subjected to high temperature oxidizing conditions. The ferritic stainless steel is selected from the group comprising AISI Type 430 stainless steel, AISI Type 439 stainless steel, AISI Type 441 stainless steel, AISI Type 444 stainless steel, and E-BRITE.RTM. alloy, also known as UNS 44627 stainless steel. In certain embodiments, the article of manufacture is a fuel cell interconnect for a solid oxide fuel cell.

  8. Chromium-Makes stainless steel stainless

    USGS Publications Warehouse

    Kropschot, S.J.; Doebrich, Jeff

    2010-01-01

    Chromium, a steely-gray, lustrous, hard metal that takes a high polish and has a high melting point, is a silvery white, hard, and bright metal plating on steel and other material. Commonly known as chrome, it is one of the most important and indispensable industrial metals because of its hardness and resistance to corrosion. But it is used for more than the production of stainless steel and nonferrous alloys; it is also used to create pigments and chemicals used to process leather.

  9. Effect of substrate bias on the structural and electrical properties of sputtered Mo thin films on flexible substrates.

    PubMed

    Xu, Jiaxiong

    2016-01-01

    The metal molybdenum (Mo) thin films deposited on flexible substrates can act as the contact electrode of flexible Cu(In,Ga)Se2 or Cu2ZnSn(S,Se)4 solar cells. In this work, in order to enhance the structural and electrical characteristics of flexible Mo thin films, a negative substrate bias was applied during the direct current sputtering of Mo thin films. The flexible substrates used for growing the Mo films were stainless steel foils and polyimides. The characteristics of Mo thin films were studied by x-ray diffraction and sheet resistance measurements. The measured results reveal that an optimal value of negative substrate bias can be found for improving the electrical and structural characteristics of Mo thin films on flexible substrates. The minimum sheet resistances of Mo thin films are 2.50 Ω/sq and 2.73 Ω/sq for the stainless steel foil and polyimide substrates, respectively. PMID:27339280

  10. Phase transformations in cast duplex stainless steels

    NASA Astrophysics Data System (ADS)

    Kim, Yoon-Jun

    Duplex stainless steels (DSS) constitute both ferrite and austenite as a matrix. Such a microstructure confers a high corrosion resistance with favorable mechanical properties. However, intermetallic phases such as sigma (sigma) and chi (chi) can also form during casting or high-temperature processing and can degrade the properties of the DSS. This research was initiated to develop time-temperature-transformation (TTT) and continuous-cooling-transformation (CCT) diagrams of two types of cast duplex stainless steels, CD3MN (Fe-22Cr-5Ni-Mo-N) and CD3MWCuN (Fe-25Cr-7Ni-Mo-W-Cu-N), in order to understand the time and temperature ranges for intermetallic phase formation. The alloys were heat treated isothermally or under controlled cooling conditions and then characterized using conventional metallographic methods that included tint etching, and also using electron microscopy (SEM, TEM) and wavelength dispersive spectroscopy (WDS). The kinetics of intermetallic-phase (sigma + chi) formation were analyzed using the Johnson-Mehl-Avrami (JMA) equation in the case of isothermal transformations and a modified form of this equation in the case of continuous cooling transformations. The rate of intermetallic-phase formation was found to be much faster in CD3MWCuN than CD3MN due mainly to differences in the major alloying contents such as Cr, Ni and Mo. To examine in more detail the effects of these elements of the phase stabilities, a series of eight steel castings was designed with the Cr, Ni and Mo contents systematically varied with respect to the nominal composition of CD3MN. The effects of varying the contents of alloying additions on the formation of intermetallic phases were also studied computationally using the commercial thermodynamic software package, Thermo-Calc. In general, a was stabilized with increasing Cr addition and chi by increasing Mo addition. However, a delicate balance among Ni and other minor elements such as N and Si also exists. Phase equilibria in

  11. Phase Transformations in Cast Duplex Stainless Steels

    SciTech Connect

    Yoon-Jun Kim

    2004-12-19

    Duplex stainless steels (DSS) constitute both ferrite and austenite as a matrix. Such a microstructure confers a high corrosion resistance with favorable mechanical properties. However, intermetallic phases such as {sigma} and {chi} can also form during casting or high-temperature processing and can degrade the properties of the DSS. This research was initiated to develop time-temperature-transformation (TTT) and continuous-cooling-transformation (CCT) diagrams of two types of cast duplex stainless steels, CD3MN (Fe-22Cr-5Ni-Mo-N) and CD3MWCuN (Fe-25Cr-7Ni-Mo-W-Cu-N), in order to understand the time and temperature ranges for intermetallic phase formation. The alloys were heat treated isothermally or under controlled cooling conditions and then characterized using conventional metallographic methods that included tint etching, and also using electron microscopy (SEM, TEM) and wavelength dispersive spectroscopy (WDS). The kinetics of intermetallic-phase ({sigma} + {chi}) formation were analyzed using the Johnson-Mehl-Avrami (MA) equation in the case of isothermal transformations and a modified form of this equation in the case of continuous cooling transformations. The rate of intermetallic-phase formation was found to be much faster in CD3MWCuN than CD3MN due mainly to differences in the major alloying contents such as Cr, Ni and Mo. To examine in more detail the effects of these elements of the phase stabilities; a series of eight steel castings was designed with the Cr, Ni and Mo contents systematically varied with respect to the nominal composition of CD3MN. The effects of varying the contents of alloying additions on the formation of intermetallic phases were also studied computationally using the commercial thermodynamic software package, Thermo-Calc. In general, {sigma} was stabilized with increasing Cr addition and {chi} by increasing Mo addition. However, a delicate balance among Ni and other minor elements such as N and Si also exists. Phase equilibria in

  12. Sensitization of stainless steel

    NASA Technical Reports Server (NTRS)

    Nagy, James P.

    1990-01-01

    The objective of this experiment is to determine the corrosion rates of 18-8 stainless steels that have been sensitized at various temperatures and to show the application of phase diagrams. The laboratory instructor will assign each student a temperature, ranging from 550 C to 1050 C, to which the sample will be heated. Further details of the experimental procedure are detailed.

  13. Welding of Stainless Materials

    NASA Technical Reports Server (NTRS)

    Bull, H; Johnson, Lawrence

    1929-01-01

    It would appear that welds in some stainless steels, heat-treated in some practicable way, will probably be found to have all the resistance to corrosion that is required for aircraft. Certainly these structures are not subjected to the severe conditions that are found in chemical plants.

  14. Corrosion characteristics of ferric and austenitic stainless steels for dental magnetic attachment.

    PubMed

    Endo, K; Suzuki, M; Ohno, H

    2000-03-01

    The corrosion behaviors of four ferric stainless steels and two austenitic stainless steels were examined in a simulated physiological environment (0.9% NaCl solution) to obtain basic data for evaluating the appropriate composition of stainless steels for dental magnetic attachments. The corrosion resistance was evaluated by electrochemical techniques and the analysis of released metal ions by atomic absorption spectrophotometry. The surface of the stainless steels was analyzed by X-ray photoelectron spectroscopy (XPS). The breakdown potential of ferric stainless steels increased and the total amount of released metal ions decreased linearly with increases in the sum of the Cr and Mo contents. The corrosion rate of the ferric stainless steels increased 2 to 6 times when they were galvanically coupled with noble metal alloys but decreased when coupled with commercially pure Ti. For austenitic stainless steels, the breakdown potential of high N-bearing stainless steel was approximately 500 mV higher than that of SUS316L, which is currently used as a component in dental magnetic attachments. The enriched nitrogen at the alloy/passive film interface may be effective in improving the localized corrosion resistance. PMID:11219089

  15. Copper modified austenitic stainless steel alloys with improved high temperature creep resistance

    DOEpatents

    Swindeman, R.W.; Maziasz, P.J.

    1987-04-28

    An improved austenitic stainless steel that incorporates copper into a base Fe-Ni-Cr alloy having minor alloying substituents of Mo, Mn, Si, T, Nb, V, C, N, P, B which exhibits significant improvement in high temperature creep resistance over previous steels. 3 figs.

  16. Delta ferrite-containing austenitic stainless steel resistant to the formation of undesirable phases upon aging

    SciTech Connect

    Leitnaker, J.M.

    1981-05-05

    Austenitic stainless steel alloys containing delta ferrite, such as are used as weld deposits, are protected against the transformation of delta ferrite to sigma phase during aging by the presence of carbon plus nitrogen in a weight percent 015-0.030 times the volume percent ferrite present in alloy. The formation of chi phase upon aging is controlled by controlling the mo content.

  17. Cast alumina forming austenitic stainless steels

    DOEpatents

    Muralidharan, Govindarajan; Yamamoto, Yukinori; Brady, Michael P

    2013-04-30

    An austenitic stainless steel alloy consisting essentially of, in terms of weight percent ranges 0.15-0.5C; 8-37Ni; 10-25Cr; 2.5-5Al; greater than 0.6, up to 2.5 total of at least one element selected from the group consisting of Nb and Ta; up to 3Mo; up to 3Co; up to 1W; up to 3Cu; up to 15Mn; up to 2Si; up to 0.15B; up to 0.05P; up to 1 total of at least one element selected from the group consisting of Y, La, Ce, Hf, and Zr; <0.3Ti+V; <0.03N; and, balance Fe, where the weight percent Fe is greater than the weight percent Ni, and wherein the alloy forms an external continuous scale comprising alumina, and a stable essentially single phase FCC austenitic matrix microstructure, the austenitic matrix being essentially delta-ferrite free and essentially BCC-phase-free. A method of making austenitic stainless steel alloys is also disclosed.

  18. The resistance to cavitation erosion of CrMnN stainless steels

    SciTech Connect

    Fu, W.T.; Jing, T.F.; Zheng, Y.Z.; Yang, Y.B.; Yao, M.

    1998-12-01

    The resistance to cavitation erosion (CE) was measured using a magnetostrictive device and a rotating disk device for some CrMnN stainless steels (Chinese patent ZL 90 1 02197.0). The microstructural changes in the surface layer before and after CE were analyzed by use of Mossbauer spectra. Results show that the resistance to CE of duplex austenitic-martensitic CrMnN stainless steels is much better than that of ZG0Cr13Ni4-6Mo and ZG0Cr16Ni5Mo steel, which are in common use for hydraulic turbine runners. The metastable austenite and its changes in the process of CE are the key factors why the CrMnN stainless steels have excellent resistance to cavitation erosion.

  19. Substitution for chromium in 304 stainless steel. [effects on oxidation and corrosion resistance

    NASA Technical Reports Server (NTRS)

    Stephens, J. R.; Barrett, C. A.

    1978-01-01

    An investigation was conducted to determine the effects of substituting less strategic elements for Cr on oxidation and corrosion resistance of AISI 304 stainless steel. Cyclic oxidation resistance was evaluated at 870 C. Corrosion resistance was determined by exposure of specimens to a boiling copper-rich solution of copper sulfate and sulfuric acid. Alloy substitutes for Cr included Al, Mn, Mo, Si, Ti, V, Y, and misch metal. A level of about 12% Cr was the minimum amount of Cr required for adequate oxidation and corrosion resistance in the modified composition 304 stainless steels. This represents a Cr saving of 33 percent. Two alloys containing 12% Cr plus 2% Al plus 2% Mo and 12% Cr plus 2.65% Si were identified which exhibited oxidation and corrosion resistance comparable to AISI 304 stainless steel.

  20. Phosphate ytterbium-doped single-mode all-solid photonic crystal fiber with output power of 13.8 W

    PubMed Central

    Wang, Longfei; He, Dongbing; Feng, Suya; Yu, Chunlei; Hu, Lili; Qiu, Jianrong; Chen, Danping

    2015-01-01

    Single-mode ytterbium-doped phosphate all-solid photonic crystal fiber (AS-PCF) with 13.8 W output power and 32% slope efficiency was reported. By altering the diameter of the rods around the doped core and thus breaking the symmetry of the fiber, a polarization-maintaining AS-PCF with degree of polarization of >85% was also achieved, for the first time to knowledge, in a phosphate PCF. PMID:25684731

  1. Compatibility Assessment of Advanced Stainless Steels in Sodium

    SciTech Connect

    Pawel, Steven J

    2012-01-01

    Type 316L stainless steel capsules containing commercially pure sodium and miniature tensile specimens of HT-UPS (austenitic, 14Cr-16Ni), NF-616 (ferritic/martensitic, 9Cr-2W-0.5Mo), or 316L (austenitic, 17Cr-10Ni-2Mo) stainless steel were exposed at 600 or 700 C for 100 and 400 h as a screening test for compatibility. Using weight change, tensile testing, and metallographic analysis, HT-UPS and 316L were found to be largely immune to changes resulting from sodium exposure, but NF-616 was found susceptible to substantial decarburization at 700 C. Subsequently, two thermal convection loops (TCLs) constructed of 316L and loaded with commercially pure sodium and miniature tensile specimens of HT-UPS and 316L were operated for 2000 h each one between 500 and 650 C, the other between 565 and 725 C at a flow rate of about 1.5 cm/s. Changes in specimen appearance, weight, and tensile properties were observed to be very minor in all cases, and there was no metallographic evidence of microstructure changes, composition gradients, or mass transfer resulting from prolonged exposure in a TCL. Thus, it appears that HT-UPS and 316L stainless steels are similarly compatible with commercially pure sodium under these exposure conditions.

  2. Martensitic stainless steel seamless linepipe with superior weldability and CO{sub 2} corrosion resistance

    SciTech Connect

    Miyata, Y.; Kimura, M.; Koseki, T.; Toyooka, T.; Murase, F.

    1997-08-01

    Two types of new martensitic stainless steel with good weldability and superior corrosion resistance have been developed for line pipe application. Both steels are suitable for welding without preheating owing to lowering C and N contents, and they show good low temperature toughness in welds without PWHT. One is applied to sweet environments. It gives better resistance to CO{sub 2} corrosion than the 13Cr martensitic stainless steel for OCTG. Lowering C and addition of Ni contribute to reduction of general corrosion rate in the CO{sub 2} environment. The addition of Cu improves the pitting resistance. The other is applied to light sour environments. It gives good SSC resistance in welds owing to the improvement of the pitting resistance due to Mo addition. The seamless pipes of these martensitic stainless steels are applicable as substitutes for a part of duplex stainless steel flow lines.

  3. New Economical 19Cr Duplex Stainless Steels

    NASA Astrophysics Data System (ADS)

    Li, Jun; Zhang, Zixing; Chen, Hong; Xiao, Xueshan; Zhao, Junliang; Jiang, Laizhu

    2012-02-01

    New economical duplex stainless steels (DSSs) containing 19Cr-6Mn- xNi-1.0Mo-0.5W-0.5Cu-0.2N ( x = 0.5 to 2.0) were developed, and the microstructure, impact property, and corrosion resistance of the alloys were studied. The ferrite content increases with the solution treatment temperature, but decreases with an increase in nickel. The sigma phase is not found precipitating in the alloys treated with solution from 1023 K to 1523 K (750 °C to 1250 °C). The low-temperature impact energy of the experimental alloys increases first and then decreases rapidly with an increase in nickel, which is mainly due to the martensite transformation with an increase in austenite. The alloys have a better mechanical property and pitting corrosion resistance than AISI 304. Among the designed DSS alloys, 19Cr-6Mn-1.3Ni-1.0Mo-0.5W-0.5Cu-0.2N is found to be an optimum alloy with proper phase proportion, a better combination of mechanical strength and elongation, and higher pitting corrosion resistance compared with those of the other alloys.

  4. Photodesorption from stainless steels

    NASA Technical Reports Server (NTRS)

    Mesarwi, A.; Ignatiev, A.

    1988-01-01

    The photodesorption by low-energy photons from three types of stainless steels is examined. For all these systems both CO and CO2 were observed to photodesorb with high yields: about 0.001 molecules/photon for CO2 and about 0.0001 molecules/photon for CO at 250 nm. The observed threshold energies were found to be the same for all systems at E0 = 2.92 eV for CO2 and E0 = 2.92-3.10 eV for CO.

  5. Cavitation Erosion of Sensitized UNS S31803 Duplex Stainless Steels

    NASA Astrophysics Data System (ADS)

    Mitelea, Ion; Micu, Lavinia Mădălina; Bordeaşu, Ilare; Crăciunescu, Corneliu Marius

    2016-05-01

    During processing or use, duplex steels can be subjected to heating at high temperatures that can affect their behavior. This work aims to correlate the influence of the sensitization treatment on the ultrasonic cavitation erosion behavior of a UNS S31803 (X2CrNiMoN22-5-3) duplex stainless steel. Duplex stainless steels, formed as a result of rapid cooling after solution annealing, are sensitized at temperatures of 475 and 850 °C, respectively, leading to hardening and embrittlement due to the spinodal decomposition of the ferrite and the precipitation of secondary phases. The ultrasonic cavitation erosion experiments showed that the sensitization at 850 °C reduced the mean depth of erosion by about 11% and the mean depth of erosion rate by 28%. By contrast, the sensitization at 475 °C deteriorates the cavitation erosion resistance, increasing the erosion parameters by up to 22%, compared to the solution annealed state.

  6. Cavitation Erosion of Sensitized UNS S31803 Duplex Stainless Steels

    NASA Astrophysics Data System (ADS)

    Mitelea, Ion; Micu, Lavinia Mădălina; Bordeaşu, Ilare; Crăciunescu, Corneliu Marius

    2016-04-01

    During processing or use, duplex steels can be subjected to heating at high temperatures that can affect their behavior. This work aims to correlate the influence of the sensitization treatment on the ultrasonic cavitation erosion behavior of a UNS S31803 (X2CrNiMoN22-5-3) duplex stainless steel. Duplex stainless steels, formed as a result of rapid cooling after solution annealing, are sensitized at temperatures of 475 and 850 °C, respectively, leading to hardening and embrittlement due to the spinodal decomposition of the ferrite and the precipitation of secondary phases. The ultrasonic cavitation erosion experiments showed that the sensitization at 850 °C reduced the mean depth of erosion by about 11% and the mean depth of erosion rate by 28%. By contrast, the sensitization at 475 °C deteriorates the cavitation erosion resistance, increasing the erosion parameters by up to 22%, compared to the solution annealed state.

  7. Corrosion resistance of stainless steels

    SciTech Connect

    Dillon, C.P.

    1995-12-31

    This book reviews the mechanisms and forms of corrosion and examines the corrosion of stainless steels and similar chromium-bearing nickel containing higher alloys, detailing various corrosive environments including atmospheric and fire-side corrosion, corrosion by water and soil, and corrosion caused by particular industrial processes. It provides information on specific groups and grades of stainless steels; summarizes typical applications for specific stainless alloys; describes common corrosion problems associated with stainless steels; presents the acceptable isocorrosion parameters of concentration and temperature for over 250 chemicals for which stainless steels are the preferred materials of construction; discusses product forms and their availability; elucidates fabrication, welding, and joining techniques; and covers the effects of pickling and passivation.

  8. Molds for electroslag casting systems. [2-1/4 Cr-1 Mo steel, 9 Cr-1 Mo steel

    SciTech Connect

    Bhat, G.K.

    1985-07-01

    This report describes the basic types of molds used for the manufacture of electroslag castings. The report also provides guidelines for the design of such molds based on heat generation and heat transfer considerations pertaining to the electroslag casting process. The designs of the two-step and three-step molds used for the manufacture of electroslag castings of 2-1/4 Cr-1 Mo steel, 316 stainless steel and 9 Cr-1 Mo steel are provided as examples of cost effective mold construction using cooled copper liners for metal-slag containment. 5 refs., 12 figs.

  9. Case Study of the Failure of two 13.8kV Control & Metering Transformers that caused significant Equipment Damage

    SciTech Connect

    Dreifuerst, G R; Chew, D B; Mangonon, H L; Swyers, P W

    2011-08-25

    The degradation and failure of cast-coil epoxy windings within 13.8kV control power transformers and metering potential transformers has been shown to be dangerous to both equipment and personnel, even though best industrial design practices were followed. Accident scenes will be examined for two events at a U.S. Department of Energy laboratory. Failure modes will be explained and current design practices discussed with changes suggested to prevent a recurrence and to minimize future risk. New maintenance philosophies utilizing partial discharge testing of the transformers as a prediction of end-of-life will be examined.

  10. Switch to duplex stainless steels

    SciTech Connect

    Quik, J.M.A.; Geudeke, M.

    1994-11-01

    Duplex stainless steels contain approximately equal proportions of ferrite and austenite. These stainless steels have become an established material of construction in the chemical process industries (CPI). Duplexes offer benefits over austenitic stainless steels and carbon steels because of their higher strength, and good toughness and ductility, in combination with equivalent resistance to general corrosion, as well as better resistance to localized corrosion and stress corrosion cracking. Additionally, duplex materials have thermal-conductivity and thermal-expansion coefficients similar to those of ferritic materials, are tough at low (sub-zero) temperatures, and have a high resistance to erosion and abrasion. In some of the highly corrosive environments encountered in the CPI, the super duplex stainless steels offer cost-effective options not possible with the standard austenitic stainless steels. The initial applications were almost exclusively as heat exchanger tubing in water-cooled service. In recent times, duplex stainless steels have been used in the oil, gas, and chemical industries. Examples include service in sweet and mildly sour corrosive environments, on offshore platforms where weight savings can be realized, and as a replacement for standard austenitic stainless steel in chemical-processing plants.

  11. Corrosion behavior of stainless steel by oxygen and tellurium at low oxygen potentials

    NASA Astrophysics Data System (ADS)

    Furuya, H.; Saito, M.; Sugisaki, M.

    1988-06-01

    Oxidation behavior of SUS-316 stainless steel was investigated under oxygen pressures ranging from 10 -23 Pa (as controlled by a {Mo}/{MoO 2} buffer) to 10 -13 Pa (as controlled by a {Ni}/{NiO} buffer). Te-induced corrosion was studied under the oxygen pressure controlled by the {Mo}/{MoO 2} buffer. Based on the kinetic and metallographical data and thermodynamic consideration, the reaction mechanism was discussed. Under the oxygen pressures controlled by the {Mo}/{MoO 2} buffer, a single oxide film was formed on the specimen surface and its growth rate was governed by lattice and grain-boundary diffusion of Cr in the stainless steel substrate. Under the oxygen pressures controlled by the {Ni}/{NiO} buffer, a duplex oxide film was formed and its growth rate depended on the outward diffusion of Fe ions in the outer oxide layer. In the case of simultaneous reaction by O and Te, it was found that the uptakes of these elements increases beyond about 10 Pa Te pressure and the reaction rate was controlled by the outward diffusion of Fe and Ni in the inner reaction layer.

  12. Corrosion Resistance of Powder Metallurgy Processed TiC/316L Composites with Mo Additions

    NASA Astrophysics Data System (ADS)

    Lin, Shaojiang; Xiong, Weihao

    2015-06-01

    To find out the effects of Mo addition on corrosion resistance of TiC/316L stainless steel composites, TiC/316L composites with addition of different contents of Mo were prepared by powder metallurgy. The corrosion resistance of these composites was evaluated by the immersion tests and polarization curves experiments. Results indicated that Mo addition decreased the corrosion rates of TiC/316L composites in H2SO4 solution in the case of Mo content below 2% whereas it displayed an opposite effect when Mo content was above that value. It was found that with an increase in the Mo content, the pitting corrosion resistance increased monotonically for TiC/316L composites in NaCl solution.

  13. Stainless steel display evaluation

    NASA Astrophysics Data System (ADS)

    Hopper, Darrel G.; Meyer, Frederick M.; Longo, Sam J.; Trissell, Terry L.

    2007-04-01

    Active matrix organic light emitting diode (AMOLED) technology is one candidate to become a low power alternative in some applications to the currently dominant, active matrix liquid crystal display (AMLCD), technology. Furthermore, fabrication of the AMOLED on stainless steel (SS) foil rather than the traditional glass substrate, while presenting a set of severe technical challenges, opens up the potential for displays that are both lighter and less breakable. Also, transition to an SS foil substrate may enable rollable displays - large when used but small for stowage within gear already worn or carried or installed. Research has been initiated on AMOLED/SS technology and the first 320 x 240 color pixel 4-in. demonstration device has been evaluated in the AFRL Display Test and Evaluation Laboratory. Results of this evaluation are reported along with a research roadmap.

  14. Welding tritium exposed stainless steel

    SciTech Connect

    Kanne, W.R. Jr.

    1994-11-01

    Stainless steels that are exposed to tritium become unweldable by conventional methods due to buildup of decay helium within the metal matrix. With longer service lives expected for tritium containment systems, methods for welding on tritium exposed material will become important for repair or modification of the systems. Solid-state resistance welding and low-penetration overlay welding have been shown to mitigate helium embrittlement cracking in tritium exposed 304 stainless steel. These processes can also be used on stainless steel containing helium from neutron irradiation, such as occurs in nuclear reactors.

  15. Microstructure and tensile behavior of nitrogen-alloyed, dual-phase stainless steels

    SciTech Connect

    Berns, H.; Kleff, J.; Krauss, G.; Foley, R.P.

    1996-07-01

    Two alloys of high-nitrogen stainless steel have been heat treated to produce dual-phase microstructures. The first alloy, N10CrNiMo17 1, a Ni-containing stainless steel, was processed conventionally. The second alloy, N20CrMo17, a Ni-free stainless steel, was processed to obtain a higher nitrogen content by pressurized electroslag remelting. The martensite in N10CrNiMo17 1 was homogeneously distributed in the ferrite and obtained a near-constant volume fraction as a function of intercritical annealing temperature. Microprobe analysis and microhardness measurements of the martensite constituent suggested that up to 0.4 pct N was dissolved in the austenite before quenching. Austenite formation, martensite transformation, undissolved nitrides, and retained austenite were evaluated by transmission electron microscopy (TEM). The Ni-containing alloy exhibited classic dual-phase tensile behavior in that continuous yielding was observed together with good combinations of ultimate tensile strength and total elongation. The martensite constituent in alloy N20CrMo17 was concentrated within bands. Comparison of tensile properties of the two alloys at similar volume fractions and hardness levels of martensite and ferrite showed that the microstructure containing banded martensite had inferior combinations of strength and ductility. The degradation of tensile ductility was accompanied by a fracture mode transition from microvoid coalescence to transgranular cleavage. The deformation and fracture behavior of both alloys were related to the microstructure.

  16. Properties of Superconducting Mo, Mo2n and Trilayer Mo2n-Mo-Mo2n Thin Films

    NASA Technical Reports Server (NTRS)

    Barrentine, E. M.; Stevenson, T. R.; Brown, A. D.; Lowitz, A. E.; Noroozian, O.; U-Yen, K.; Eshan, N.; Hsieh, W. T.; Moseley, S. H.; Wollack, E. J.

    2014-01-01

    We present measurements of the properties of thin film superconducting Mo, Mo2N and Mo2N/Mo/Mo2N trilayers of interest for microwave kinetic inductance detector (MKID) applications. Using microwave resonator devices, we investigate the transition temperature, energy gaps, kinetic inductance, and internal quality factors of these materials. We present an Usadel-based interpretation of the trilayer transition temperature as a function of trilayer thicknesses, and a 2-gap interpretation to understand the change in kinetic inductance and internal resonance quality factor (Q) as a function of temperature.

  17. Brazing titanium to stainless steel

    NASA Technical Reports Server (NTRS)

    Batista, R. I.

    1980-01-01

    Titanium and stainless-steel members are usually joined mechanically for lack of any other effective method. New approach using different brazing alloy and plating steel member with nickel resolves problem. Process must be carried out in inert atmosphere.

  18. Evaluation of pitting corrosion resistance of high-alloyed stainless steels welds for FGD plants in Korea

    SciTech Connect

    Baek, K.K.; Sung, H.J.; Im, C.S.; Hong, I.P.; Kim, D.K.

    1998-12-31

    For successful application of high-alloyed stainless steels for Flue Gas Desulfurization (FGD) plants, pitting corrosion resistance of arc welds of N-added 6%Mo austenitic stainless steels (UNS N 08367) and super duplex stainless steels (UNS S 32550) made with various filler metals were evaluated using the Green Death solution. For Gas Tungsten Arc (GTA) and Gas Metal Arc (GMA) welds of N 08367, Critical Pitting Temperature (CPT) of base metal was 65--70 C, whereas weld made by ERNiCrMo-3 filler metal yielded CPT of 50 C. Welds made by ERNiCrMo-10 or ERNiCrMo-4 filler metals showed CPT of 60--65 C and 65--70C, respectively. For GTA and GMA welds of S 32550, CPT of welds made by ERNiCrMo-3 was 45--50 C, indicating that the filler metal can provide pitting corrosion resistance matching the S 32550 alloy. Thus, a proper pitting corrosion resistance of weldments of high-alloy stainless steels can be achieved by selecting filler metals having at least +10 higher Pitting Resistance Equivalent Number (PRE{sub N}) value than the base metal regardless of the type of arc welding process. The over-alloyed filler metals would compensate preferential segregation of Cr, MO along the dendrite boundary, which made the dendrite core more susceptible to pitting. Nitrogen addition to the GTA welds of N 08367 made with ERNiCrMo-3 failed to improve pitting corrosion resistance, which was attributed to the precipitation of nitrogen in the weld metal in the form of Nb-nitride.

  19. Why stainless steel corrodes.

    PubMed

    Ryan, Mary P; Williams, David E; Chater, Richard J; Hutton, Bernie M; McPhail, David S

    2002-02-14

    Stainless steels are used in countless diverse applications for their corrosion resistance. Although they have extremely good general resistance, they are nevertheless susceptible to pitting corrosion. This localized dissolution of an oxide-covered metal in specific aggressive environments is one of the most common and catastrophic causes of failure of metallic structures. The pitting process has been described as random, sporadic and stochastic and the prediction of the time and location of events remains extremely difficult. Many contested models of pitting corrosion exist, but one undisputed aspect is that manganese sulphide inclusions play a critical role. Indeed, the vast majority of pitting events are found to occur at, or adjacent to, such second-phase particles. Chemical changes in and around sulphide inclusions have been postulated as a mechanism for pit initiation but such variations have never been measured. Here we use nanometre-scale secondary ion mass spectroscopy to demonstrate a significant reduction in the Cr:Fe ratio of the steel matrix around MnS particles. These chromium-depleted zones are susceptible to high-rate dissolution that 'triggers' pitting. The implications of these results are that materials processing conditions control the likelihood of corrosion failures, and these data provide a basis for optimizing such conditions. PMID:11845203

  20. Stainless Steel Permeability

    SciTech Connect

    Buchenauer, Dean A.; Karnesky, Richard A.

    2015-09-01

    An understanding of the behavior of hydrogen isotopes in materials is critical to predicting tritium transport in structural metals (at high pressure), estimating tritium losses during production (fission environment), and predicting in-vessel inventory for future fusion devices (plasma driven permeation). Current models often assume equilibrium diffusivity and solubility for a class of materials (e.g. stainless steels or aluminum alloys), neglecting trapping effects or, at best, considering a single population of trapping sites. Permeation and trapping studies of the particular castings and forgings enable greater confidence and reduced margins in the models. For FY15, we have continued our investigation of the role of ferrite in permeation for steels of interest to GTS, through measurements of the duplex steel 2507. We also initiated an investigation of the permeability in work hardened materials, to follow up on earlier observations of unusual permeability in a particular region of 304L forgings. Samples were prepared and characterized for ferrite content and coated with palladium to prevent oxidation. Issues with the poor reproducibility of measurements at low permeability were overcome, although the techniques in use are tedious. Funding through TPBAR and GTS were secured for a research grade quadrupole mass spectrometer (QMS) and replacement turbo pumps, which should improve the fidelity and throughput of measurements in FY16.

  1. Oxidation and corrosion behavior of modified-composition, low-chromium 304 stainless steel alloys

    NASA Technical Reports Server (NTRS)

    Stephens, J. R.; Barrett, C. A.

    1977-01-01

    The effects of substituting less strategic elements than Cr on the oxidation and corrosion resistance of AISI 304 stainless steel were investigated. Cyclic oxidation resistance was evaluated at 870 C. Corrosion resistance was determined by exposure of specimens to a boiling copper-rich solution of copper sulfate and sulfuric acid. Alloy substitutes for Cr included Al, Mn, Mo, Si, Ti, V, Y, and misch metal. A level of about 12% Cr was the minimum amount of Cr required for adequate oxidation and corrosion resistance in the modified composition 304 stainless steels. This represents a Cr saving of at least 33%. Two alloys containing 12% Cr and 2% Al plus 2% Mo and 12% Cr plus 2.65% Si were identified as most promising for more detailed evaluation.

  2. Austenitic stainless steel for high temperature applications

    DOEpatents

    Johnson, Gerald D.; Powell, Roger W.

    1985-01-01

    This invention describes a composition for an austenitic stainless steel which has been found to exhibit improved high temperature stress rupture properties. The composition of this alloy is about (in wt. %): 12.5 to 14.5 Cr; 14.5 to 16.5 Ni; 1.5 to 2.5 Mo; 1.5 to 2.5 Mn; 0.1 to 0.4 Ti; 0.02 to 0.08 C; 0.5 to 1.0 Si; 0.01 maximum, N; 0.02 to 0.08 P; 0.002 to 0.008 B; 0.004-0.010 S; 0.02-0.05 Nb; 0.01-0.05 V; 0.005-0.02 Ta; 0.02-0.05 Al; 0.01-0.04 Cu; 0.02-0.05 Co; 0.03 maximum, As; 0.01 maximum, O; 0.01 maximum, Zr; and with the balance of the alloy being essentially iron. The carbon content of the alloy is adjusted such that wt. % Ti/(wt. % C+wt. % N) is between 4 and 6, and most preferably about 5. In addition the sum of the wt. % P+wt. % B+wt. % S is at least 0.03 wt. %. This alloy is believed to be particularly well suited for use as fast breeder reactor fuel element cladding.

  3. Heat treatment giving a stable high temperature micro-structure in cast austenitic stainless steel

    DOEpatents

    Anton, Donald L.; Lemkey, Franklin D.

    1988-01-01

    A novel micro-structure developed in a cast austenitic stainless steel alloy and a heat treatment thereof are disclosed. The alloy is based on a multicomponent Fe-Cr-Mn-Mo-Si-Nb-C system consisting of an austenitic iron solid solution (.gamma.) matrix reinforced by finely dispersed carbide phases and a heat treatment to produce the micro-structure. The heat treatment includes a prebraze heat treatment followed by a three stage braze cycle heat treatment.

  4. Performance of high molybdenum superaustenitic stainless steel welds in harsh chloride environments

    SciTech Connect

    Stenvall, P.; Liljas, M.; Wallen, B.

    1996-11-01

    Superaustenitic steels are normally welded with nickel-based alloys as filler materials. To clarify the understanding of weld behavior in superaustenitic stainless steels this paper presents the development history of 6Mo and 7Mo steels, and results of laboratory tests and field tests on welds of UNS S31254 (6Mo) and UNS S32654 (7 Mo) in different types of chloride containing environments. The laboratory tests consisted of the well known ferric chloride test (ASTM G 48 Method A). Shielded metal arc welds, gas tungsten arc welds and submerged arc welds in both grades were tested. The critical pitting temperatures were determined and the locations of the attack were noted. Some specimens were sectioned at the position of the attack followed by studies using light optical microscopy. The critical pitting temperatures of the welds in S31254 and S32654 were at normal levels for both grades, i.e., 40--50 C for S31254 and 60--75 C for S32654. The locations of the attack differed depending on the welding process. In shielded metal arc welds the attack was mostly located in the weld metal. In gas tungsten arc welds the attack was predominantly located next to the fusion line. The field tests showed that the behavior of welds and parent metal of superaustenitic stainless steels, as well as of nickel-based alloys, is much dependent on the corrosive environment. In oxidizing chloride solutions, similar results to those of the ferric chloride test, are observed. However, crevice corrosion in the parent material is at a greater risk than pitting corrosion in the welds. In very oxidizing solutions of low chloride concentrations, welds made of nickel-based fillers may corrode faster than the stainless steel base metal due to transpassive uniform corrosion. The opposite situation exists when active uniform corrosion prevails, i.e., welds made of nickel-based fillers corrode less than the stainless steel parent material.

  5. Delta ferrite-containing austenitic stainless steel resistant to the formation of undesirable phases upon aging

    DOEpatents

    Leitnaker, J.M.

    Austenitic stainless steel alloys containing delta ferrite, such as are used as weld deposits, are protected against the transformation of delta ferrite to sigma phase during aging by the presence of carbon plus nitrogen in a weight percent 0.015 to 0.030 times the volume percent ferrite present in the alloy. The formation of chi phase upon aging is controlled by controlling the Mo content.

  6. Delta ferrite-containing austenitic stainless steel resistant to the formation of undesirable phases upon aging

    DOEpatents

    Leitnaker, James M.

    1981-01-01

    Austenitic stainless steel alloys containing delta ferrite, such as are used as weld deposits, are protected against the transformation of delta ferrite to sigma phase during aging by the presence of carbon plus nitrogen in a weight percent 0.015-0.030 times the volume percent ferrite present in the alloy. The formation of chi phase upon aging is controlled by controlling the Mo content.

  7. Superhard Nanocrystalline Homometallic Stainless Steel on Steel for Seamless Coatings

    NASA Technical Reports Server (NTRS)

    Tobin, Eric J.; Hafley, R. (Technical Monitor)

    2002-01-01

    The objective of this work is to deposit nanocrystalline stainless steel onto steel substrates (homometallic) for enhanced wear and corrosion resistance. Homometallic coatings provide superior adhesion, and it has been shown that ultrafine-grained materials exhibit the increased hardness and decreased permeability desired for protective coatings. Nanocrystals will be produced by controlling nucleation and growth and use of an ion beam during deposition by e-beam evaporation or sputtering. Phase I is depositing 31 6L nanocrystalline stainless steel onto 31 6L stainless steel substrates. These coatings exhibit hardnesses comparable to those normally obtained for ceramic coatings such ZrO2, and possess the superior adhesion of seamless, homometallic coatings. Hardening the surface with a similar material also enhances adhesion, by avoiding problems associated with thermal and lattice mismatch. So far we have deposited nanocrystalline homometallic 316L stainless steel coatings by varying the ions and the current density of the ion beams. For all deposition conditions we have produced smooth, uniform, superhard coatings. All coatings exhibit hardness of at least 200% harder than that of bulk materials. Our measurements indicate that there is a direct relationship between nanohardness and the current density of the ion beam. Stress measurements indicate that stress in the films is increasingly proportional to current density of the ion beam. TEM, XPS, and XRD results indicate that the coated layers consist of FCC structure nanocrystallites with a dimension of about 10 to 20 nm. The Ni and Mo concentration of these coating are lower than those of bulk 316L but the concentration of Cr is higher.

  8. Corrosion resistance of weldable super 13Cr stainless steel in H{sub 2}S containing CO{sub 2} environments

    SciTech Connect

    Ueda, M.; Amaya, H.; Kondo, K.; Ogawa, K.; Mori, T.

    1996-08-01

    The weldable super 13Cr stainless steel was investigated because of the application for flow line in CO{sub 2} environments with a little amount of H{sub 2}S. TIG welding in the condition of no post weld heat treatment (PWHT) was used as the welding technique. The lowering of C content less than 0.01 mass% in the weldable steel decreased a maximum hardness in the heat-affected zone(HAZ) and mitigated the sulfide stress cracking (SSC) susceptibility. The increasing of Mo content from 2.0 mass% of the super 13Cr stainless steel OCTG (0.02C-12Cr-5.5Ni-2Mo) to 2.5 mass% improved SSC resistance in the HAZ. Based on these results, the weldable super 13Cr stainless steel, which consisted of 0.007C-12Cr-6Ni-2.5Mo-Ti, has been developed. The welded-joint with the yield strength of 550 MPa (80 ksi) and enough corrosion resistance was completed by using the welding material of super duplex stainless steel which had 25Cr-9Ni-3Mo-2W-0.3N. The corrosion resistance to SSC at room temperatures and localized-corrosion at elevated temperatures of the welded-joint was the same as the super 13Cr stainless steel OCTG. The improvement effect of the corrosion resistance by means of Mo addition was discussed based on the stability of Cr oxide passive film, the analysis results of the surface film formed in the CO{sub 2} environment containing H{sub 2}S, and calculated-solubility of oxides, FeCO{sub 3} and sulfides in that environment. It was clarified that Mo assisted the formation of the Cr oxide passive film in the inner layer of the surface film and the formation of Mo sulfide in the outer layer.

  9. Plating on stainless steel alloys

    SciTech Connect

    Dini, J.W.; Johnson, H.R.

    1981-09-11

    Quantitative adhesion data are presented for a variety of electroplated stainless steel type alloys. Results show that excellent adhesion can be obtained by using a Wood's nickel strike or a sulfamate nickel strike prior to final plating. Specimens plated after Wood's nickel striking failed in the deposit rather than at the interface between the substrate and the coating. Flyer plate quantitative tests showed that use of anodic treatment in sulfuric acid prior to Wood's nickel striking even further improved adhesion. In contrast activation of stainless steels by immersion or cathodic treatment in hydrochloric acid resulted in very reduced bond strengths with failure always occurring at the interface between the coating and substrate.

  10. Estimating 13.8-GHz path-integrated attenuation from 10.7-GHz brightness temperatures for the TRMM combined PR-TMI precipitation algorithm

    SciTech Connect

    Smith, E.A.; Farrar, M.R.; Xiang, X.; Turk, F.J.; Mugnai, A.

    1997-04-01

    This study presents research in support of the design and implementation of a combined radar-radiometer algorithm to be used for precipitation retrieval during the Tropical Rainfall Measuring Mission (TRMM). The combined algorithm approach is expected to overcome various difficulties that arise with a radar-only approach, particularly related to estimates of path-integrated attenuation (PIA)along the TRMM radar beam. A technique is described for estimating PIA at the 13.8-GHz frequency of the TRMM precipitation radar (PR) from 10.7-GHz brightness temperature T{sub B} measurements obtained from the TRMM microwave imager. Through the use of variational or probabilistic techniques, the independent PIA calculations provide a means to adjust for errors that accumulate in estimates of range-dependent rain rates at progressively increasing range positions from radar reflectivity vectors. The accepted radar approach for obtaining PIA from ocean-viewing radar reflectivity measurements is called the surface reference technique, a scheme based on the difference in ocean surface cross sections between cloud-free and raining radar pixels. This technique has encountered problems, which are discussed and analyzed with the aid of coordinated aircraft radar (Airborne Rain Mapping Radar) and radiometer (Advanced Microwave Precipitation Radiometer) measurements obtained during the west Pacific Tropical Ocean Global Atmosphere Coupled Ocean-Atmosphere Response Experiment in 1993. 97 refs., 12 figs., 5 tabs.

  11. A Simple Synthetic Route to MoS2 and WS2 Nanoparticles and Thin Films

    NASA Astrophysics Data System (ADS)

    Lee, G. H.; Jeong, J. W.; Huh, S. H.; Kim, S. H.; Choi, B. J.; Kim, Y. W.

    We produced both MoS2 and WS2 nanoparticles by thermally decomposing M(CO)6 (M = Mo, W) in excess of H2S by using a hot filament. Both highly pure crystalline MoS2 and WS2 nanoparticles were efficiently produced over the filament temperature range from 300 to 800 °C. Particle diameter ranged from 2.0 to 5.0 nm and from 3.0 to 6.0 nm for MoS2 and WS2 nanoparticles, respectively. Fullerene-like particles such as nanotubes, onions, and empty and nested hollows were not produced. Both MoS2 and WS2 nanoparticles have a hexagonal close packed structure. Cell constants are determined to be a = 3.09 and c = 12.61 Å and a = 3.09 and c = 12.47 Å for MoS2 and WS2 nanoparticles, respectively, which are all consistent with the corresponding bulk values. Thin films of MoS2 and WS2 were also prepared by chemical vapor deposition of MoS2 and WS2 on stainless steel disks at 600-650 °C and low friction coefficients were obtained at an ambient atmosphere for both MoS2 and WS2 thin films, implying that they can serve as good solid lubricants.

  12. Evaluation of stainless steel zirconium alloys as high-level nuclear waste forms

    NASA Astrophysics Data System (ADS)

    McDeavitt, S. M.; Abraham, D. P.; Park, J. Y.

    1998-09-01

    Stainless steel-zirconium (SS-Zr) alloys have been developed for the consolidation and disposal of waste stainless steel, zirconium, and noble metal fission products such as Nb, Mo, Tc, Ru, Pd, and Ag recovered from spent nuclear fuel assemblies. These remnant waste metals are left behind following electrometallurgical treatment, a molten salt-based process being demonstrated by Argonne National Laboratory. Two SS-Zr compositions have been selected as baseline waste form alloys: (a) stainless steel-15 wt% zirconium (SS-15Zr) for stainless steel-clad fuels and (b) zirconium-8 wt% stainless steel (Zr-8SS) for Zircaloy-clad fuels. Simulated waste form alloys were prepared and tested to characterize the metallurgy of SS-15Zr and Zr-8SS and to evaluate their physical properties and corrosion resistance. Both SS-15Zr and Zr-8SS have multi-phase microstructures, are mechanically strong, and have thermophysical properties comparable to other metals. They also exhibit high resistance to corrosion in simulated groundwater as determined by immersion, electrochemical, and vapor hydration tests. Taken together, the microstructure, physical property, and corrosion resistance data indicate that SS-15Zr and Zr-8SS are viable materials as high-level waste forms.

  13. Corrosion behavior of 2205 duplex stainless steel.

    PubMed

    Platt, J A; Guzman, A; Zuccari, A; Thornburg, D W; Rhodes, B F; Oshida, Y; Moore, B K

    1997-07-01

    The corrosion of 2205 duplex stainless steel was compared with that of AISI type 316L stainless steel. The 2205 stainless steel is a potential orthodontic bracket material with low nickel content (4 to 6 wt%), whereas the 316L stainless steel (nickel content: 10 to 14 wt%) is a currently used bracket material. Both stainless steels were subjected to electrochemical and immersion (crevice) corrosion tests in 37 degrees C, 0.9 wt% sodium chloride solution. Electrochemical testing indicates that 2205 has a longer passivation range than 316L. The corrosion rate of 2205 was 0.416 MPY (milli-inch per year), whereas 316L exhibited 0.647 MPY. When 2205 was coupled to 316L with equal surface area ratio, the corrosion rate of 2205 reduced to 0.260 MPY, indicating that 316L stainless steel behaved like a sacrificial anode. When 316L is coupled with NiTi, TMA, or stainless steel arch wire and was subjected to the immersion corrosion test, it was found that 316L suffered from crevice corrosion. On the other hand, 2205 stainless steel did not show any localized crevice corrosion, although the surface of 2205 was covered with corrosion products, formed when coupled to NiTi and stainless steel wires. This study indicates that considering corrosion resistance, 2205 duplex stainless steel is an improved alternative to 316L for orthodontic bracket fabrication when used in conjunction with titanium, its alloys, or stainless steel arch wires. PMID:9228844

  14. Adsorption of pure carbon dioxide on wet Argonne coals at 328.2 K and pressures up to 13.8 MPa

    SciTech Connect

    S.A. Mohammad; J.S. Chen; J.E. Fitzgerald; R.L. Robinson, Jr.; K.A.M. Gasem

    2009-01-15

    Carbon dioxide (CO{sub 2}) adsorption isotherms were measured on five different rank coals at 328.2 K and pressures up to 13.8 MPa using a volumetric method. Specifically, Beulah Zap, Illinois no.6, Pocahontas No.3, Upper Freeport, and Wyodak coals from the Argonne premium coal sample program were used for these isotherm measurements. These newly acquired data are compared to our previous data on dry coals. As expected, the adsorption on the wet coals is lower than that on the dry coals. At 7 MPa, Pocahontas, Upper Freeport, Illinois no. 6, Wyodak, and Beulah Zap coals exhibited, respectively, about 19, 17, 48, 76, and 79% reduction in the amount adsorbed on the wet coal when compared to the adsorption on the dry coal. These reductions in CO{sub 2} adsorption correlate positively with the amount of moisture present on the coal. The isotherms on wet coals were measured at their equilibrium moisture content. The adsorption isotherm for each of the wet coals exhibited a Gibbs adsorption maximum between 8 and 12 MPa and occurred at a higher pressure than that of the dry coal. The simplified local-density/Peng-Robinson model was used to correlate the adsorption data. The model was found capable of representing precisely the CO{sub 2} adsorption on both dry and wet coals. Specifically, the overall weighed average absolute deviation (WAAD) for the five dry and wet coals was 0.99 and 0.42, respectively. Nevertheless, more rigorous accounting for the water interactions with the coal matrix and the competitive adsorption between water and CO{sub 2} would provide an even more realistic description of coal-bed gas adsorption phenomenon on wet coals. 43 refs., 10 figs., 9 tabs.

  15. The behavior of stainless steels in physiological solution containing complexing agent studied by X-ray photoelectron spectroscopy.

    PubMed

    Milosev, I; Strehblow, H H

    2000-11-01

    The passive film formed by electrochemical oxidation on two different stainless steels differing in molybdenum (Mo) content in physiological solution with and without the addition of complexing agent, i.e., citrate, was studied using X-ray photoelectron spectroscopy. The alloys were polarized at different oxidation potentials in the electrochemical chamber attached to the spectrometer. Thus, the composition of the film formed by oxidation was analyzed by X-ray photoelectron spectroscopy without prior exposure to air (quasi in situ). The passive film formed in physiological solution consists of two predominant oxides, i.e., chromium and iron oxides. Oxides of alloying elements nickel and Mo are also detected in the film. It seems that the strong enrichment of oxidized chromium and Mo in the passive layer, and strong enrichment of Mo and depletion of iron at the metal surface underneath the passive layer, are responsible for the outstanding corrosion resistance of orthopedic stainless steel in physiological solution. Commercial AISI 304 is not suitable for orthopedic applications. The addition of complexing agent affects significantly the passivation behavior of orthopedic stainless steel, because it changes the distribution of the elements within the passive layer and at the metal surface underneath. PMID:10951382

  16. Nickel release from stainless steels.

    PubMed

    Haudrechy, P; Mantout, B; Frappaz, A; Rousseau, D; Chabeau, G; Faure, M; Claudy, A

    1997-09-01

    In 1994, a study of nickel release and allergic contact dermatitis from nickel-plated metals and stainless steels was published in this journal. It was shown that low-sulfur stainless steel grades like AISI 304, 316L or 430 (S < or = 0.007%) release less than 0.03 microgram/cm2/week of nickel in acid artificial sweat and elicit no reactions in patients already sensitized to nickel. In contrast, nickel-plated samples release around 100 micrograms/cm2/week of Ni and high-sulfur stainless steel (AISI 303-S approximately 0.3%) releases about 1.5 micrograms/cm2/week in this acid artificial sweat. Applied on patients sensitized to nickel, these metals elicit positive reactions in 96% and 14%, respectively, of the patients. The main conclusion was that low-sulfur stainless steels like AISI 304, 316L or 430, even when containing Ni, should not elicit nickel contact dermatitis, while metals having a mean corrosion resistance like a high-sulfur stainless steel (AISI 303) or nickel-plated steel should be avoided. The determining characteristic was in fact the corrosion resistance in chloride media, which, for stainless steels, is connected, among other factors, to the sulfur content. Thus, a question remained concerning the grades with an intermediate sulfur content, around 0.03%, which were not studied. They are the object of the study presented in this paper. 3 tests were performed: leaching experiments, dimethylglyoxime and HNO3 spot tests, and clinical patch tests; however, only stainless steels were tested: a low-sulfur AISI 304 and AISI 303 as references and 3 grades with a sulfur content around 0.03%: AISI 304L, AISI 304L added with Ca, AISI 304L+Cu. Leaching experiments showed that the 4 non-resulfurised grades released less than 0.5 microgram/cm2/week in acid sweat while the reulfurized AISI 303 released around or more than 0.5 microgram/cm2/week. This is explained by the poorer corrosion resistance of the resulfurized grade. Yet all these grades had the same

  17. Influence of ultrasonic cavitation on passive film of stainless steel.

    PubMed

    Wang, Bao-Cheng; Zhu, Jin-hua

    2008-03-01

    The electrochemical behaviors of passive film of stainless steel 0Cr13Ni5Mo under the condition of static state (quiescence) and ultrasonic cavitation in the HCl solution have been studied by means of polarization curve, electrochemical impedance spectroscopy (EIS) and capacitance potential measurement. The results indicate that the passive film shows a multi layer structure distribution, and presents a p-type semiconductor property under the condition of quiescence. The stability of passive film decreases, the semiconducting property changes to an n-type semiconductor in the presence of cavitation. The amount of transition electrons from valence band because of cavitation is related to the height of Fermi level of passive film semiconductor. PMID:17584517

  18. Nickel: makes stainless steel strong

    USGS Publications Warehouse

    Boland, Maeve A.

    2012-01-01

    Nickel is a silvery-white metal that is used mainly to make stainless steel and other alloys stronger and better able to withstand extreme temperatures and corrosive environments. Nickel was first identified as a unique element in 1751 by Baron Axel Fredrik Cronstedt, a Swedish mineralogist and chemist. He originally called the element kupfernickel because it was found in rock that looked like copper (kupfer) ore and because miners thought that "bad spirits" (nickel) in the rock were making it difficult for them to extract copper from it. Approximately 80 percent of the primary (not recycled) nickel consumed in the United States in 2011 was used in alloys, such as stainless steel and superalloys. Because nickel increases an alloy's resistance to corrosion and its ability to withstand extreme temperatures, equipment and parts made of nickel-bearing alloys are often used in harsh environments, such as those in chemical plants, petroleum refineries, jet engines, power generation facilities, and offshore installations. Medical equipment, cookware, and cutlery are often made of stainless steel because it is easy to clean and sterilize. All U.S. circulating coins except the penny are made of alloys that contain nickel. Nickel alloys are increasingly being used in making rechargeable batteries for portable computers, power tools, and hybrid and electric vehicles. Nickel is also plated onto such items as bathroom fixtures to reduce corrosion and provide an attractive finish.

  19. Electroslag-casting process and properties. [2. 25Cr-1 Mo and modified 9Cr-1Mo

    SciTech Connect

    Sikka, V.K.

    1986-09-01

    The electroslag-casting process is an extension of the electroslag-remelting process. The castings produced by this technique have the advantages of smooth defect-free finish, freedom from conventional casting defects, more reproducible mechanical properties, and properties comparable to those of forged products. This report describes the current status of electroslag-casting facilities in Canada and the United States. It also describes the variety of electroslag castings of 2.25Cr-1Mo, modified 9Cr-1Mo, and type 316 stainless steel made during the last four years and the detailed chemical analysis, microstructural characterization, and mechanical property characterization. The mechanical properties are compared with those of the forged and wrought material. This report provides sufficient information about the electroslag-casting process and the properties of the castings to permit consideration of the process for approval by ASTM and ASME Boiler and Pressure Vessel Code committees. 27 refs., 53 figs., 34 tabs.

  20. Localized weld metal corrosion in stainless steel water tanks

    SciTech Connect

    Strum, M.J.

    1995-05-25

    The rapidly developed leaks within the TFC and TFD tanks (LLNL groundwater treatment facilities) were caused by localized corrosion within the resolidified weld metal. The corrosion was initiated by the severe oxidation of the backsides of the welds which left the exposed surfaces in a condition highly susceptible to aqueous corrosion. The propagation of surface corrosion through the thickness of the welds occurred by localized corrosive attack. This localized attack was promoted by the presence of shielded aqueous environments provided by crevices at the root of the partial penetration welds. In addition to rapid corrosion of oxidized surfaces, calcium carbonate precipitation provided an additional source of physical shielding from the bulk tank environment. Qualification testing of alternate weld procedures showed that corrosion damage can be prevented in 304L stainless steel GTA welds by welding from both sides while preventing oxidation of the tank interior through the use of an inert backing gas such as argon. Corrosion resistance was also satisfactory in GMA welds in which oxidized surfaces were postweld cleaned by wire brushing and chemically passivated in nitric acid. Further improvements in corrosion resistance are expected from a Mo-containing grade of stainless steel such as type 316L, although test results were similar for type 304L sheet welded with type 308L filler metal and type 316L sheet welded with type 316L filler metal.

  1. Phase Evolution and Properties of Al2CrFeNiMo x High-Entropy Alloys Coatings by Laser Cladding

    NASA Astrophysics Data System (ADS)

    Wu, Wei; Jiang, Li; Jiang, Hui; Pan, Xuemin; Cao, Zhiqiang; Deng, Dewei; Wang, Tongmin; Li, Tingju

    2015-10-01

    A series of Al2CrFeNiMo x ( x = 0 to 2.0 at.%) high-entropy alloys coatings was synthesized on stainless steel by laser cladding. The effect of Mo content on the microstructures and mechanical properties of Al2CrFeNiMo x coatings was studied. The results show that the laser clad layer consists of the cladding zone, bonding zone, and heat-affected zone. The Al2CrFeNiMo x coatings are composed of two simple body-center cubic phases and the cladding zone is mainly composed of equiaxed grains. When the content of Mo reaches 2 at.%, a eutectic structure is found in the interdendritic regions. The surface microhardness of the Al2CrFeNiMo2 coating is 678 HV, which is about three times higher than that of the substrate (243 HV). Compared with stainless steel, the wear resistance of the coatings has been improved greatly. The wear mass loss of the Al2CrFeNiMo alloy is 9.8 mg, which is much less than that of the substrate (18.9 mg) and its wear scar width is the lowest among the Al2CrFeNiMo x coatings, indicating that the wear resistance of the Al2CrFeNiMo is the best.

  2. Corrosion-resistant amorphous metallic films of Mo49Cr33B18 alloy

    NASA Technical Reports Server (NTRS)

    Ramesham, R.; Distefano, S.; Fitzgerald, D.; Thakoor, A. P.; Khanna, S. K.

    1987-01-01

    Corrosion-resistant amorphous metallic alloy films of Mo49Cr33B18 with a crystallization temperature of 590 C were deposited onto glass and quartz substrates by magnetron sputter-quench technique. The amorphous nature of the films was confirmed by their diffuse X-ray diffraction patterns. The deposited films are densely packed (zone T) and exhibit low stress and good adhesion to the substrate. Corrosion current of as-deposited coating of MoCrB amorphous metallic alloy is approximately three orders of magnitude less than the corrosion current of 304 stainless steel in 1N H2SO4 solution.

  3. Microbial corrosion of stainless steel.

    PubMed

    Ibars, J R; Moreno, D A; Ranninger, C

    1992-11-01

    Stainless steel, developed because of their greater resistance to corrosion in different aggressive environments, have proved to be affected, however, by various processes and types of corrosion. Some of these types of corrosion, mainly pitting, is activated and developed in the presence of microorganisms, which acting in an isolated or symbiotic way, according to their adaptation to the environment, create a favorable situation for the corrosion of these steel. The microorganisms that are involved, mainly bacteria of both the aerobic and anaerobic type, modify the environment where the stainless steel is found, creating crevices, differential aeration zones or a more aggressive environment with the presence of metabolites. In these circumstances, a local break of the passive and passivating layer is produced, which is proper to these types of steel and impedes the repassivation that is more favorable to corrosion. In the study and research of these types of microbiologically influenced corrosion are found electrochemical techniques, since corrosion is fundamentally an electrochemical process, and microbiological techniques for the identification, culture, and evaluation of the microorganisms involved in the process, as well as in the laboratory or field study of microorganism-metal pairs. Microstructural characterization studies of stainless steel have also been considered important, since it is known that the microstructure of steel can substantially modify their behavior when faced with corrosion. As for surface analysis studies, it is known that corrosion is a process that is generated on and progresses from the surface. The ways of dealing with microbiologically influenced corrosion must necessarily include biocides, which are not always usable or successful, the design of industrial equipment or components that do not favor the adherence of microorganisms, using microstructures in steel less sensitive to corrosion, or protecting the materials. PMID:1492953

  4. Alloy 31, a new 6 moly stainless steel with improved corrosion resistance in seawater

    SciTech Connect

    Jasner, M.; Heubner, U.

    1995-10-01

    Alloy 31--UNS N08031--31Ni-27Cr-6.5Mo-1.2Cu-0.2N-balance iron--is an advanced 6 Mo stainless steel with increased chromium and nickel, contents for seawater service. In hot seawater the pitting potential of alloy 31 remains high up to 90 C (194 F). Investigations of resistance to crevice corrosion in real piping systems in natural seawater, both North Sea and Baltic Sea, show that the threshold conditions for alloy 31 in chlorinated seawater (North Sea) are at 40 C and 1 ppm chlorine well superior to the 6 Mo stainless grades being currently in use. In addition, alloy 31 shows an excellent resistance to corrosion versus both hot reducing media (e.g. H{sub 2}SO{sub 4}) and hot oxidizing media (e.g. HNO{sub 3}). The combination of high resistance to localized corrosion vs. hot chloride-bearing cooling waters including seawater and aggressive oxidizing and reducing hot corrosive media is a unique feature of alloy 31. Alloy 31 is recommended for the construction of heat exchangers, process coolers and piping systems. The material is supplied in a number of semifinished products such as seamless and welded pipes, fittings, flanges, forged bars, plate, sheet, strip, wire and prefabricated piping systems.

  5. JOINING OF MOLYBDENUM DISILICIDE TO STAINLESS STEEL USING AMORPHOUS METAL BRAZES-RESIDUAL STRESS ANALYSIS

    SciTech Connect

    VAIDYA, RAJENDRA U; KAUTZ, DOUGLAS D.; GALLEGOS, DAVID E.

    2007-01-30

    Molybdenum disilicide (MoSi{sub 2})/stainless steel 316 L jOints were produced by high temperature brazing using a cobalt-based metallic-glass (METGLAS{trademark} 2714A). Successful joining was completed in two different ways; either by feeding excess braze into the braze gap upon heating or by constraining the MoSi{sub 2}/stainiess steel assembly with an alumina (Al{sub 2}O{sub 3}) fixture during the heating cycle. These steps were necessary to ensure the production of a high quality void free joint. Residual stress measurements were completed on these joints. Indentation results show higher tensile residual stresses in the stainless steel for the joint with the external constraint, in comparison to the unconstrained state. In contrast, the compressive residual stresses In the MoSi{sub 2} (as measured by X-ray diffraction) were lower in the constrained state relative to the unconstrained state. These results and a lack of residual stress balance indicate that the stress state in the braze is significantly different under the two joining conditions and the volume of the braze plays an important role in the development of the residual stresses. Push-out tests carried out on these joints gave higher joint strengths in the unconstrained as compared to the constrained condition. The results of this study have important implications on the selection of the appropriate joining process (use of constraint versus extra braze).

  6. METHOD FOR JOINING ALUMINUM TO STAINLESS STEEL

    DOEpatents

    Lemon, L.C.

    1960-05-24

    Aluminum may be joined to stainless steel without the use of flux by tinning the aluminum with a tin solder containing 1% silver and 1% lead, tinning the stainless steel with a 50% lead 50% tin solder, and then sweating the tinned surfaces together.

  7. Microstructure of a plasma-sprayed Mo-Si-B alloy

    NASA Astrophysics Data System (ADS)

    Kramer, M. J.; Okumus, S. C.; Besser, M. F.; Ünal, Ö.; Akinc, M.

    2000-03-01

    Powders of Mo52Si38B10 were plasma sprayed under inert conditions onto stainless steel substrates to determine if high density free standing forms could be synthesized by this process. Thermal spray conditions were varied to minimize porosity and oxygen impurities while minimizing evaporative metal losses. The assprayed and sintered microstructures were characterized using scanning and transmission electron microscopy and quantitative x-ray diffraction (XRD). The as-sprayed microstructure consisted of elongated splats tens of microns in length and only one to three microns in thickness. The splats contained submicrometer grains of primarily MoB and Mo5Si3B x (T1) and minor amounts of MoSi2 and a glassy grain boundary phase. The interior of the splats typically consisted of a fine eutectic of MoB and T1. Small pieces were cut out of the cross section of the sample and pressureless sintered for 2, 6, and 10 h at 1800 °C in flowing Ar. After sintering for 2 h at 1800 °C, the samples exhibited a coarser but equiaxed microstructure (1 to 5 µm grain size) containing 78 vol.% T1, 16 vol.% MoB, and 6 vol.% MoSi2 as determined by XRD. Approximately 8 at.% of the Si formed silica. The high-temperature anneal removed all vestiges of the layered structure observed in the as-sprayed samples.

  8. Constitution and thermodynamics of the Mo-Ru, Mo-Pd, Ru-Pd and Mo-Ru-Pd systems

    NASA Astrophysics Data System (ADS)

    Kleykamp, H.

    1989-09-01

    The constitution of the Mo-Ru, Mo-Pd and Ru-Pd systems was reinvestigated between 800 and 2000°C. The Mo-Ru system is of the eutectic type, a σ-phase Mo 5Ru 3 exists between 1915 and 1143°C. The Mo-Pd system is characterized by an hcp phase Mo 9Pd 11 and by two peritectic reactions, β- Mo( Pd) + L = Mo9Pd11andMo9Pd11 + L = α- Pd( Mo). Mo 9Pd 11 decomposes eutectoidally at 1370°C. The Ru-Pd system is simple peritectic. The continuous series of the hcp solid solutions between Mo 9Pd 11 and ɛ-Ru(Mo, Pd) in the ternary Mo-Ru-Pd system observed at 1700°C are suppressed below 1370°C near the Mo-Pd boundary system by the formation of a narrow α + β + ɛ three-phase field. Relative partial molar Gibbs energies of Mo, Mo and Ru in the respective binary systems and of Mo in the ternary system were measured by the EMF method with a Zr(Ca)O 2 electrolyte. xsΔ ḠMo∞ quantities were evaluated at 1200 K which give -43 kJ/mol Mo in Ru and -94 kJ/mol Mo in Pd at infinite dilution. Gibbs energies of formation of the Mo-Ru and Mo-Pd systems were calculated.

  9. Mechanical properties and oxidation and corrosion resistance of reduced-chromium 304 stainless steel alloys

    NASA Technical Reports Server (NTRS)

    Stephens, J. R.; Barrett, C. A.; Gyorgak, C. A.

    1979-01-01

    An experimental program was undertaken to identify effective substitutes for part of the Cr in 304 stainless steel as a method of conserving the strategic element Cr. Although special emphasis was placed on tensile properties, oxidation and corrosion resistance were also examined. Results indicate that over the temperature range of -196 C to 540 C the yield stress of experimental austenitic alloys with only 12 percent Cr compare favorably with the 18 percent Cr in 304 stainless steel. Oxidation resistance and in most cases corrosion resistance for the experimental alloys were comparable to the commercial alloy. Effective substitutes for Cr included Al, Mo, Si, Ti, and V, while Ni and Mn contents were increased to maintain an austenitic structure.

  10. Interaction between stainless steel and plutonium metal

    SciTech Connect

    Dunwoody, John T; Mason, Richard E; Freibert, Franz J; Willson, Stephen P; Veirs, Douglas K; Worl, Laura A; Archuleta, Alonso; Conger, Donald J

    2010-01-01

    Long-term storage of excess plutonium is of great concern in the U.S. as well as abroad. The current accepted configuration involves intimate contact between the stored material and an iron-bearing container such as stainless steel. While many safety scenario studies have been conducted and used in the acceptance of stainless steel containers, little information is available on the physical interaction at elevated temperatures between certain forms of stored material and the container itself. The bulk of the safety studies has focused on the ability of a package to keep the primary stainless steel containment below the plutonium-iron eutectic temperature of approximately 410 C. However, the interactions of plutonium metal with stainless steel have been of continuing interest. This paper reports on a scoping study investigating the interaction between stainless steel and plutonium metal in a pseudo diffusion couple at temperatures above the eutectic melt-point.

  11. The comparison of frictional resistance in titanium, self-ligating stainless steel, and stainless steel brackets using stainless steel and TMA archwires: An in vitro study

    PubMed Central

    Khalid, Syed Altaf; Kumar, Vadivel; Jayaram, Prithviraj

    2012-01-01

    Aim: The aim of the study was to compare the frictional resistance of titanium, self-ligating stainless steel, and conventional stainless steel brackets, using stainless steel and titanium molybdenum alloy (TMA) archwires. Materials and Methods: We compared the frictional resistance in 0.018 slot and 0.022 slot of the three brackets – titanium, self-ligating stainless steel, and conventional stainless steel – using stainless steel archwires and TMA archwires. An in vitro study of simulated canine retraction was undertaken to evaluate the difference in frictional resistance between titanium, self-ligating stainless steel, and stainless steel brackets, using stainless steel and TMA archwires. Results and Conclusion: We compared the frictional resistance of titanium, self-ligating stainless steel, and conventional stainless steel brackets, using stainless steel and TMA archwires, with the help of Instron Universal Testing Machine. One-way analysis of variance (ANOVA), Student's “t” test, and post hoc multiple range test at level of <0.05 showed statistically significant difference in the mean values of all groups. Results demonstrated that the titanium, self-ligating stainless steel, and stainless steel brackets of 0.018-inch and 0.022-inch slot had no significant variations in frictional résistance. The self-ligating bracket with TMA archwires showed relatively less frictional resistance compared with the other groups. The titanium bracket with TMA archwires showed relatively less frictional resistance compared with the stainless steel brackets. PMID:23066253

  12. Development of New Stainless Steel

    SciTech Connect

    Robert F. Buck

    2005-08-30

    A new family of innovative martensitic stainless steels, 521-A, 521-B, and 521-C has been developed by Advanced Steel Technology, LLC (Trafford, PA) as high strength fastener (bolt) materials for use at moderate temperatures in turbine engines, including steam turbines, gas turbines, and aircraft engines. The primary objective of the development program was to create a martensitic stainless steel with high strength at moderate temperatures, and which could replace the expensive nickel-based superalloy IN 718 in some fasteners applications. A secondary objective was to replace conventional 12Cr steels such as AISI 422 used as blades, buckets and shafts that operate at intermediate temperatures in turbine engines with stronger steel. The composition of the new alloys was specifically designed to produce excellent mechanical properties while integrating heat treatment steps into production to reduce energy consumption during manufacturing. As a result, production costs and energy consumption during production of rolled bar products is significantly lower than conventional materials. Successful commercialization of the new alloys would permit the installed cost of certain turbine engines to be reduced without sacrificing high availability or operational flexibility, thereby enhancing the global competitiveness of U.S. turbine engine manufacturers. Moreover, the domestic specialty steel industry would also benefit through increased productivity and reduced operating costs, while increasing their share of the international market for turbine engine fasteners, blades, buckets and shafts.

  13. EBSD investigation of the microstructure and texture characteristics of hot deformed duplex stainless steel.

    PubMed

    Cizek, P; Wynne, B P; Rainforth, W M

    2006-05-01

    The microstructure and crystallographic texture characteristics were studied in a 22Cr-6Ni-3Mo duplex stainless steel subjected to plastic deformation in torsion at a temperature of 1000 degrees C using a strain rate of 1 s(-1). High-resolution EBSD was successfully used for precise phase and substructural characterization of this steel. The austenite/ferrite ratio and phase morphology as well as the crystallographic texture, subgrain size, misorientation angles and misorientation gradients corresponding to each phase were determined over large sample areas. The deformation mechanisms in each phase and the interrelationship between the two are discussed. PMID:16774517

  14. Microstructural Evolution in 2101 Lean Duplex Stainless Steel During Low- and Intermediate-Temperature Aging.

    PubMed

    Maetz, Jean-Yves; Cazottes, Sophie; Verdu, Catherine; Danoix, Frédéric; Kléber, Xavier

    2016-04-01

    The microstructural evolution of a 2101 lean duplex stainless steel (DSS) during isothermal aging from room temperature to 470 °C was investigated using thermoelectric power (TEP) measurements to follow the kinetics, atom probe tomography, and transmission electron microscopy. Despite the low Ni, Cr, and Mo contents, the lean DSS was sensitive to α-α' phase separation and Ni-Mn-Si-Al-Cu clustering at intermediate temperatures. The time-temperature pairs characteristic of the early stages of ferrite decomposition were determined from the TEP kinetics. Considering their composition and locations, the clusters are most likely G phase precursors. PMID:26940550

  15. In vivo evaluation of a high-strength, high-ductility stainless steel for use in surgical implants.

    PubMed

    Syrett, B C; Davis, E E

    1979-07-01

    A high-strength, high-ductility, austenitic stainless steel has been evaluated for use in surgical implants by performing in vivo tests in rats, rabbits, dogs, and rhesus monkeys. This stainless steel, a TRIP (Transformation Induced Plasticity) steel containing about 4% Mo, was compared with two alloys in current clinical use: Type 316L stainless steel and cast Vitallium. Compared with the other two alloys, cast Vitallium generally had higher resistance to corrosion and superior biocompatibility in all animals. The tests in rats and dogs indicated that the corrosion resistances of the TRIP steel and the Type 316L stainless steel were similar and that the tissue reactions caused by these alloys were also similar. However, in rhesus monkeys, the TRIP steel was shown to be susceptible to stress-corrosion cracking and much more susceptible to crevice corrosion than Type 316L stainless steel. Limited tests in rabbits supported the observation that the TRIP steel is susceptible to stress-corrosion cracking. These inconsistencies in the in vivo tests underline the need for a reevaluation of the popular test techniques and of the animals commonly chosen for assessing the suitability of candidate implant materials. The "worst case" results from the rhesus monkey tests were entirely consistent with previous results obtained from in vitro studies. However, further work must be performed before the behavior of metals in humans, rhesus monkeys, or any other animal, can be predicted with confidence from an in vitro test program. PMID:110810

  16. 60 Years of duplex stainless steel applications

    SciTech Connect

    Olsson, J.; Liljas, M.

    1994-12-31

    In this paper the history of wrought duplex stainless steel development and applications is described. Ferritic-austenitic stainless steels were introduced only a few decades after stainless steels were developed. The paper gives details from the first duplex stainless steels in the 1930`s to the super duplex stainless steel development during the 1980`s. During the years much effort has been devoted to production and welding metallurgy as well as corrosion research of the duplex stainless steels. Therefore, duplex stainless steels are to-day established in a wide product range. Numerous important applications are exemplified. In most cases the selection of a duplex steel has been a result of the combination high strength excellent corrosion resistance. In the pulp and paper industry the most interesting use is as vessel material in digesters. For chemical process industry, the duplex steels are currently used in heat exchangers. The largest application of duplex steels exists in the oil and gas/offshore industry. Hundreds of kms of pipelines are installed and are still being installed. An increased use of duplex steels is foreseen in areas where the strength is of prime importance.

  17. Tritiated Water Interaction with Stainless Steel

    SciTech Connect

    Glen R. Longhurst

    2007-05-01

    Experiments conducted to study tritium permeation of stainless steel at ambient and elevated temperatures revealed that HT converts relatively quickly to HTO. Further, the HTO partial pressure contributes essentially equally with elemental tritium gas in driving permeation through the stainless steel. Such permeation appears to be due to dissociation of the water molecule on the hot stainless steel surface. There is an equilibrium concentration of HTO vapor above adsorbed gas on the walls of the experimental apparatus evident from freezing transients. The uptake process of tritium from the carrier gas involves both surface adsorption and isotopic exchange with surface bound water.

  18. Cleaning, pickling, and passivation of stainless steels

    SciTech Connect

    Dillon, C.P. )

    1994-05-01

    Stainless steels (SS) are chosen for various services because of their appearance and corrosion resistance and for their freedom from contamination in storage and shipment. However, certain conditions in handling or fabrication may make these alloys susceptible to localized corrosion or unsatisfactory performance. A surface of cleanliness, uniformity, and corrosion resistance is desirable and, in some services, absolutely required. Definitions and procedures for cleaning, pickling, and passivating stainless steels are reviewed. Surface contamination and defects including grinding marks and smut are discussed, as are measures for preventing and correcting them. The cleaning and passivating sequence required for free-machining stainless grades is included.

  19. Corrosion of stainless steel, 2. edition

    SciTech Connect

    Sedriks, A.J.

    1996-10-01

    The book describes corrosion characteristics in all the major and minor groups of stainless steels, namely, in austenitic, ferritic, martensitic, duplex, and precipitation hardenable steels. Several chapters are spent on those special forms of corrosion that are investigated in the great detail in stainless steels, namely, pitting corrosion, crevice corrosion, and stress corrosion cracking. The influences of thermal treatment (heat affected zone cases), composition, and microstructure on corrosion are given good coverage. Corrosive environments include high temperature oxidation, sulfidation as well as acids, alkalis, various different petroleum plant environments, and even human body fluids (stainless steels are commonly used prosthetic materials).

  20. Fracture-tough, high hardness stainless steel and method of making same

    NASA Technical Reports Server (NTRS)

    Olson, Gregory B. (Inventor)

    1993-01-01

    A cryogenically-formed and tempered stainless steel is provided having improved fracture toughness and corrosion resistance at a given hardness level, such as, for example, of at least about Rc 60 for bearing applications. The steel consists essentially of, in weight %, about 21 to about 24% Co, about 11 to about 13% Cr, about 7 to about 9% Ni, about 0.1 to about 0.5% Mo, about 0.2 to about 0.3% V, about 0.28 to about 0.32% C, and the balance iron. The steel includes a cryogenically-formed martensitic microstructure tempered to include about 5 to about 10 volume % post-deformation retained austenite dispersed therein and M.sub.2 C-type carbides, where M is Cr, Mo, V, and/or Fe, dispersed in the microstructure.

  1. Laser surface modification of stainless steels for cavitation erosion resistance

    NASA Astrophysics Data System (ADS)

    Kwok, Chi Tat

    1999-12-01

    Austenitic stainless steel UNS S31603 (Fe -17.6Cr -11.2Ni -2.5Mo -1.4Mn -0.4Si -0.03C) has higher pitting corrosion resistance but lower cavitation erosion resistance than that of UNS S30400. This is because of its lower tendency for strain induced martensitic transformation and higher stacking fault energy as compared with those of UNS S30400. In order to improve its cavitation erosion resistance, surface modification of S31603 was performed by laser surface melting and laser surface alloying using a 2-kW CW Nd-YAG laser and a 3-kW CW CO2 laser. For laser surface melting, austenitic stainless steel UNS S30400, super duplex stainless steel UNS S32760 and martensitic stainless steel UNS S42000 were also investigated for comparison purpose. For laser surface alloying, alloying materials including various elements (Co, Cr, Ni, Mo, Mn, Si & C), alloys (AlSiFe & NiCrSiB), ceramics (Si3N 4, SiC, Cr3C2, TiC, CrB & Cr2O 3) and alloys-ceramics (Co-WC, Ni-WC, Ni-Al2O3, Ni-Cr2C3) were used to modify the surface of S31603. The alloyed surface was achieved first by flame spraying or pre-placing of the alloy powder on the S31603 surface and then followed by laser surface remelting. The cavitation erosion characteristics of laser surface modified specimens in 3.5% NaCl solution at 23°C were studied by means of a 20-kHz ultrasonic vibrator at a peak-to-peak amplitude of 30 mum. In addition, their pitting corrosion behaviour was evaluated by electrochemical techniques. The microstructures, compositions, phase changes and damage mechanisms under cavitation erosion were investigated by optical microscopy, SEM, EDAX and X-ray diffractometry. Mechanical properties such as microhardness profile were also examined. The cavitation erosion resistance Re (reciprocal of the mean depth of penetration rate) of laser surface melted S31603 was found to be improved by 22% and was attributed to the existence of tensile residual stress. Improvement on the Re of S42000 was found to be 8.5 times

  2. Strength comparison of allogenic bone screws, bioabsorbable screws, and stainless steel screw fixation.

    PubMed

    Rano, James A; Savoy-Moore, Ruth T; Fallat, Lawrence M

    2002-01-01

    Allogenic bone screws are new to the fixation market and have yet to be tested against current fixation materials. An in vitro comparison of the same sizes of stainless steel, bioabsorbable, and allogenic bone screws was undertaken to assess screw resistance to the forces of bending, pullout, and shear. Using aluminum plates to support the screws, forces up to 1000 Newtons were applied to six to eight samples of each type of screw. During each test, stainless steel screws withstood the maximum force that could be exerted by the testing apparatus without failing (bending, 113.9 +/- 11.8 N mean +/- SE; pullout 999.1 +/- 33.7 N; and shear, 997.5 +/- 108.8 N). In each test, compared to bioabsorbable screws, allogenic bone screws failed faster (pullout, allogenic: 12.4 +/- 1.1 seconds vs. bioabsorbable, 120.6 +/- 13.8 seconds; p = .001; bending, allogenic: 53.4 +/- 4.8 seconds vs. bioabsorbable, 201.9 +/- 11.1 seconds; p = .001; shear, allogenic 13.5 +/- 1.4 seconds vs. bioabsorbable, 43.8 +/- 0.9 seconds; p = .001) under equivalent (pullout: bioabsorbable, 385.0 +/- 18.4 N vs. allogenic, 401.0 +/- 35.9 N; p = .001) or lower (bending, allogenic: 4.7 +/- 0.2 N vs. bioabsorbable, 11.0 +/- 0.9 N; p = .675; shear, allogenic: 312.1 +/- 15.5 N vs. bioabsorbable 680.9 +/- 8.5 N; p = .001) loads, and in a highly variable fashion. Overall, the bioabsorbable screws withstood the forces of bending, pullout, and shear better than the allogenic screws, and stainless steel screws outperformed both bioabsorbable and allogenic screws. Despite these results, allogenic screws could still be useful in compliant patients who would benefit from their osteoconductive properties. PMID:11858609

  3. Thermal Stability of Intermetallic Phases in Fe-rich Fe-Cr-Ni-Mo Alloys

    NASA Astrophysics Data System (ADS)

    Yang, Ying; Tan, Lizhen; Busby, Jeremy T.

    2015-09-01

    Understanding the thermal stability of intermetallic phases in Fe-rich Fe-Cr-Ni-Mo alloys is critical to alloy design and application of Mo-containing austenitic steels. Coupled with thermodynamic modeling, the thermal stability of intermetallic Chi and Laves phases in two Fe-Cr-Ni-Mo alloys was investigated at 1273 K, 1123 K, and 973 K (1000 °C, 850 °C, and 700 °C) for different annealing times. The morphologies, compositions, and crystal structures of the precipitates of the intermetallic phases were carefully examined by scanning electron microscopy, electron probe microanalysis, X-ray diffraction, and transmission electron microscopy. Two key findings resulted from this study. First, the Chi phase is stable at high temperature, and with the decreasing temperature it transforms into the Laves phase that is stable at low temperature. Secondly, Cr, Mo, and Ni are soluble in both the Chi and Laves phases, with the solubility of Mo playing a major role in the relative stability of the intermetallic phases. The thermodynamic models that were developed were then applied to evaluating the effect of Mo on the thermal stability of intermetallic phases in type 316 and NF709 stainless steels.

  4. Precise carbon control of fabricated stainless steel

    DOEpatents

    Nilsen, R.J.

    1975-12-01

    A process is described for controlling the carbon content of fabricated stainless steel components including the steps of heat treating the component in hydrogen atmospheres of varying dewpoints and carbon potentials.

  5. Hydrogen compatibility handbook for stainless steels

    SciTech Connect

    Caskey, G.R. Jr.

    1983-06-01

    This handbook compiles data on the effects of hydrogen on the mechanical properties of stainless steels and discusses this data within the context of current understanding of hydrogen compatibility of metals. All of the tabulated data derives from continuing studies of hydrogen effects on materials that have been conducted at the Savannah River Laboratory over the past fifteen years. Supplementary data from other sources are included in the discussion. Austenitic, ferritic, martensitic, and precipitation hardenable stainless steels have been studied. Damage caused by helium generated from decay of tritium is a distinctive effect that occurs in addition to the hydrogen isotopes protium and deuterium. The handbook defines the scope of our current knowledge of hydrogen effects in stainless steels and serves as a guide to selection of stainless steels for service in hydrogen.

  6. Development of a carburizing stainless steel alloy

    SciTech Connect

    Wert, D.E. )

    1994-06-01

    A new carburizing stainless steel alloy that resists corrosion, heat, and fatigue has been developed for bearing and gear applications. Pyrowear 675 Stainless alloy is vacuum induction melted and vacuum arc remelted (VIM/VAR) for aircraft-quality cleanliness. Test results show that it has corrosion resistance similar to that of AISI Type 440-C stainless, and its rolling fatigue resistance is superior to that of AISI M50 (UNS K88165). In contrast to alloy gear steels and Type 440C, Pyrowear 675 maintains case hardness of HRC 60 at operating temperatures up to 200 C (400 F). Impact and fracture toughness are superior to that of other stainless bearing steels, which typically are relatively brittle and can break under severe service. Toughness is also comparable or superior to conventional noncorrosion-resistant carburizing bearing steels, such as SAE Types 8620 and 9310.

  7. Stainless steel to titanium bimetallic transitions

    NASA Astrophysics Data System (ADS)

    Kaluzny, J. A.; Grimm, C.; Passarelli, D.

    2015-12-01

    In order to use stainless steel piping in an LCLS-II (Linac Coherent Light Source Upgrade) cryomodule, stainless steel to titanium bimetallic transitions are needed to connect the stainless steel piping to the titanium cavity helium vessel. Explosion bonded stainless steel to titanium transition pieces and bimetallic transition material samples have been tested. A sample transition tube was subjected to tests and x-ray examinations between tests. Samples of the bonded joint material were impact and tensile tested at room temperature as well as liquid helium temperature. The joint has been used successfully in horizontal tests of LCLS-II cavity helium vessels and is planned to be used in LCLS-II cryomodules. Results of material sample and transition tube tests will be presented. Operated by Fermi Research Alliance, LLC under Contract No. De-AC02-07CH11359 with the United States Department of Energy.

  8. Stainless Steel to Titanium Bimetallic Transitions

    SciTech Connect

    Kaluzny, J. A.; Grimm, C.; Passarelli, D.

    2015-01-01

    In order to use stainless steel piping in an LCLS-II (Linac Coherent Light Source Upgrade) cryomodule, stainless steel to titanium bimetallic transitions are needed to connect the stainless steel piping to the titanium cavity helium vessel. Explosion bonded stainless steel to titanium transition pieces and bimetallic transition material samples have been tested. A sample transition tube was subjected to tests and x-ray examinations between tests. Samples of the bonded joint material were impact and tensile tested at room temperature as well as liquid helium temperature. The joint has been used successfully in horizontal tests of LCLS-II cavity helium vessels and is planned to be used in LCLS-II cryomodules. Results of material sample and transition tube tests will be presented.

  9. A Duplex Stainless Steel for Chloride Environments

    NASA Astrophysics Data System (ADS)

    Sridhar, N.; Kolts, J.; Flasche, L. H.

    1985-03-01

    This paper examines the effects of microstructural changes on the corrosion, stress corrosion cracking and corrosion fatigue resistance of a duplex stainless steel to chloride environments. The microstructural changes can be precipitation of phases such as sigma and carbides, or changes in the distribution of austenite and ferrite. The former can be important in hot forming operations while the latter is important in welding. The methods of minimizing these deleterious effects can sometimes be different from those used for austenitic stainless steel.

  10. Stainless steel recycle FY94 progress report

    SciTech Connect

    Imrich, K.J.

    1994-10-28

    The Materials Technology Section (MTS) of the Savannah River Technology Center (SRTC) was asked to demonstrate the practicality of recycling previously contaminated stainless steel components such as reactor heat exchanger heads, process water piping and slug buckets into 208 liters (55 gallon) drums and 2.8 cubic meter (100 ft{sup 3}) storage boxes. Radioactively contaminated stainless steel scrap will be sent to several industrial partners where it will be melted, decontaminated/cast into ingots, and rolled into plate and sheet and fabricated into the drums and boxes. As part of this recycle initiative, MTS was requested to demonstrate that radioactively contaminated Type 304L stainless steel could be remelted and cast to meet the applicable ASTM specification for fabrication of drums and boxes. In addition, MTS was requested to develop the technical basis of melt decontamination and establish practicality of using this approach for value added products. The findings presented in this investigation lead to the following conclusions: recycle of 18 wt% Cr-8 wt% Ni alloy can be achieved by melting Type 304 stainless steel in a air vacuum induction furnace; limited melt decontamination of the contaminated stainless steel was achieved, surface contamination was removed by standard decontamination techniques; carbon uptake in the as-cast ingots resulted from the graphite susceptor used in this experiment and is unavoidable with this furnace configuration. A new furnace optimized for melting stainless steel has been installed and is currently being tested for use in this program.

  11. The abrasion-wear resistance of arc sprayed stainless steel and composite stainless steel coatings

    SciTech Connect

    Dallaire, S.; Legoux, J.G.; Levert, H.

    1994-12-31

    Stainless steels are often used to palliate wear problems in various industries. Though they are not wear resistant, they have been used to a limited extent in applications involving both corrosive and abrasive/erosive environments. The protection of industrial components by arc sprayed stainless steel composite coatings could be considered very attractive provided these coatings offer a better wear protection than bulk stainless steel. The wear resistance of stainless steel and composite stainless steel-titanium boride coatings arc sprayed with air and argon was evaluated following the ASTM G-65 Abrasion Wear Test procedures. Wear volume loss measurements show that stainless steel coatings arc sprayed with air were slightly more resistant than bulk stainless steel while those sprayed with argon were slightly less resistant. The abrasion wear resistance of composite stainless steel-titanium diboride coatings is by two or four times beyond the wear resistance of bulk stainless steel depending upon the core wire constitution and the type of gas used for spraying. Microstructural analysis of coatings, microhardness measurements of sprayed lamellae and optical profilometry were used to characterize coatings and wear damages. Spraying with air instead of argon produced much more small particles. These particles, being removed from the metal sheath surface, are individually sprayed without diluting the concentration hard phases within cores. It results in coatings that contain large lamellae with hardnesses sufficient to withstand abrasion. By considering both the wire constitution and the spraying conditions, it was found possible to fabricate composite stainless steel coatings that show a 400% increase in wear resistance over bulk stainless steel.

  12. In situ phase transformation of Laves phase from Chi-phase in Mo-containing Fe–Cr–Ni alloys

    DOE PAGESBeta

    Tan, L.; Yang, Y.

    2015-11-01

    For an in situ phase transformation of the Chi (χ) phase to the Laves phase we observed in a Fe–Cr–Ni–Mo model alloy. The morphology, composition, and crystal structure of the χ and Laves phases, and their orientation relationship with the matrix austenite phase were investigated. The resulted Laves phase has larger lattice mismatch with the matrix phase than the χ phase, leading to the increase of local strain fields and the formation of dislocations. Moreover, this finding is helpful to understand the precipitation behavior of the intermetallic phases in the Mo-containing austenitic stainless steels.

  13. A vacuum (10 exp -9 torr) friction apparatus for determining friction and endurance life of MoS(x) films

    NASA Technical Reports Server (NTRS)

    Miyoshi, Kazuhisa; Honecy, Frank S.; Abel, Phillip B.; Pepper, Stephen V.; Spalvins, Talivaldis; Wheeler, Donald R.

    1993-01-01

    An ultrahigh-vacuum tribometer for use in a ball-on-disk configuration was specially designed for measuring the friction and endurance life of magnetron-sputtered solid lubricating MoS(x) films deposited on sputter-cleaned 400 C stainless-steel disks, when slid against a 6-mm-diameter 440 C stainless-steel ball. The results of tests showed that the tribometer performs satisfactorily in unidirectional rotation in vacuum at a pressure of 10 exp -7 Pa, 10 exp -9 torr. Similarities are observed in the life cycle friction behavior and the coefficient of friction as a function of the number of disk revolutions, for MoS(x) films at average Hertzian contact from 0.33 to 0.69 GPa.

  14. An impedance study of two types of stainless steel in Ringer physiological solution containing complexing agents.

    PubMed

    Slemnik, Mojca; Milosev, Ingrid

    2006-10-01

    The effect of complexing agents EDTA and citric acid on the electrochemical behaviour of AISI 304 and orthopaedic stainless steels in Ringer physiological solution was investigated by potentiodynamic polarization method and electrochemical impedance spectroscopy (EIS). The content of Mo has a pronounced effect on the corrosion resistance, as evident by the broader passive range of the orthopaedic stainless steel containing Mo. The addition of complexing agents induces significant changes in polarization and impedance characteristics, i.e., the shift of corrosion and breakdown potentials in a more negative direction, an increase in current density, and a significant decrease in charge transfer resistance. The results were interpreted by the formation of soluble complexes of metal ions with chelating agents, especially EDTA, which suppressed the formation of the outer Fe(III) layer of the passive film. The impact of complexing agent on the electrochemical parameters was found to be related to its concentration in electrolyte and the stability constant of the complex formed with the related metal ion. PMID:16977388

  15. Microstructure and Corrosion Resistance of Laser Additively Manufactured 316L Stainless Steel

    NASA Astrophysics Data System (ADS)

    Trelewicz, Jason R.; Halada, Gary P.; Donaldson, Olivia K.; Manogharan, Guha

    2016-03-01

    Additive manufacturing (AM) of metal alloys to produce complex part designs via powder bed fusion methods such as laser melting promises to be a transformative technology for advanced materials processing. However, effective implementation of AM processes requires a clear understanding of the processing-structure-properties-performance relationships in fabricated components. In this study, we report on the formation of micro and nanoscale structures in 316L stainless steel samples printed by laser AM and their implications for general corrosion resistance. A variety of techniques including x-ray diffraction, optical, scanning and transmission electron microscopy, x-ray fluorescence, and energy dispersive x-ray spectroscopy were employed to characterize the microstructure and chemistry of the laser additively manufactured 316L stainless steel, which are compared with wrought 316L coupons via electrochemical polarization. Apparent segregation of Mo has been found to contribute to a loss of passivity and an increased anodic current density. While porosity will also likely impact the environmental performance (e.g., facilitating crevice corrosion) of AM alloys, this work demonstrates the critical influence of microstructure and heterogeneous solute distributions on the corrosion resistance of laser additively manufactured 316L stainless steel.

  16. The chloride stress-corrosion cracking behavior of stainless steels under different test methods

    NASA Astrophysics Data System (ADS)

    Jin, L. Z.

    1994-12-01

    Chloride-induced stress-corrosion cracking (SCC) is one of the failure modes of stainless steels. Highly alloyed austenitic stainless steels S32654, S31254, and N08028, and duplex grades S32750 and S31803 possess much improved resistance to SCC compared with S30400 and S31600 steels. With the development of a database, SSData, experimental data collected from calcium chloride tests, autoclave tests, and drop evaporation tests were evaluated. Stress-corrosion cracking data generated by autoclave tests agreed well with the practical service conditions and can be used to discriminate alloys for SCC resistance in sodium chloride solution. Drop evaporation test data can be used in situations where evaporation may occur and cyclic loading may be involved. The SCC resistance of alloys under each method increased with increasing molybdenum equivalent Mo + 0.25Cr + 0.1Ni. For a given alloy, the testing result depends on the stress state and environment; different test methods can give different ranking orders concerning SCC resistance. The performance of duplex stainless steels in a chloride-containing environment at higher temperatures was not as good as expected when dynamic loading was involved.

  17. Irradiation response of delta ferrite in as-cast and thermally aged cast stainless steel

    DOE PAGESBeta

    Li, Zhangbo; Lo, Wei-Yang; Chen, Yiren; Pakarinen, Janne; Wu, Yaqiao; Allen, Todd; Yang, Yong

    2015-08-08

    To enable the life extension of Light Water Reactors (LWRs) beyond 60 years, it is critical to gain adequate knowledge for making conclusive predictions to assure the integrity of duplex stainless steel reactor components, e.g. primary pressure boundary and reactor vessel internal. Microstructural changes in the ferrite of thermally aged, neutron irradiated only, and neutron irradiated after being thermally aged cast austenitic stainless steels (CASS) were investigated using atom probe tomography. The thermal aging was performed at 400 °C for 10,000 h and the irradiation was conducted in the Halden reactor at ~315 °C to 0.08 dpa (5.6 × 1019more » n/cm2 E > 1 MeV). Low dose neutron irradiation at a dose rate of 5 × 10-9 dpa/s was found to induce spinod,al decomposition in the ferrite of as-cast microstructure, and further to enhance the spinodal decomposition in the thermally aged cast alloys. Regarding the G-phase precipitates, the neutron irradiation dramatically increases the precipitate size, and alters the composition of the precipitates with increased, Mn, Ni, Si and Mo and reduced Fe and Cr contents. Lastly, The results have shown that low dose neutron irradiation can further accelerate the degradation of ferrite in a duplex stainless steel at the LWR relevant condition.« less

  18. Irradiation response of delta ferrite in as-cast and thermally aged cast stainless steel

    SciTech Connect

    Li, Zhangbo; Lo, Wei-Yang; Chen, Yiren; Pakarinen, Janne; Wu, Yaqiao; Allen, Todd; Yang, Yong

    2015-08-08

    To enable the life extension of Light Water Reactors (LWRs) beyond 60 years, it is critical to gain adequate knowledge for making conclusive predictions to assure the integrity of duplex stainless steel reactor components, e.g. primary pressure boundary and reactor vessel internal. Microstructural changes in the ferrite of thermally aged, neutron irradiated only, and neutron irradiated after being thermally aged cast austenitic stainless steels (CASS) were investigated using atom probe tomography. The thermal aging was performed at 400 °C for 10,000 h and the irradiation was conducted in the Halden reactor at ~315 °C to 0.08 dpa (5.6 × 1019 n/cm2 E > 1 MeV). Low dose neutron irradiation at a dose rate of 5 × 10-9 dpa/s was found to induce spinod,al decomposition in the ferrite of as-cast microstructure, and further to enhance the spinodal decomposition in the thermally aged cast alloys. Regarding the G-phase precipitates, the neutron irradiation dramatically increases the precipitate size, and alters the composition of the precipitates with increased, Mn, Ni, Si and Mo and reduced Fe and Cr contents. Lastly, The results have shown that low dose neutron irradiation can further accelerate the degradation of ferrite in a duplex stainless steel at the LWR relevant condition.

  19. Use of plasma arc welding process to combat hydrogen metallic disbonding of austenitic stainless steel claddings

    SciTech Connect

    Alexandrov, O.A. ); Steklov, O.I.; Alexeev, A.V. )

    1993-11-01

    A separation type crack, metallic disbonding, occurred between austenitic stainless steel weld metal cladding and 2 1/4Cr-1Mo base metal in the hydrodesulfurizing reactor of an oil refining plant. For stainless steel cladding, the submerged arc welding (SAW) process with a strip electrode is usually applied, but the authors experimented with the plasma arc welding (PAW) process with hot wire electrode for the cladding. The metallic disbonding is considered to be attributed to hydrogen accumulation at the transition zone and has been generally studied on a laboratory scale using an autoclave. The authors used a electrolytic hydrogen charging technique for the sake of experimental simplicity and made a comparison with the results for gaseous hydrogen charging. The main conclusions obtained were follows: The PAW stainless steel weld metal cladding is more resistant to metallic disbonding with the PAW process is explained by the desirable microstructure and properties of the first layer of weld metal at the transition zone. Electrolytic hydrogen charging pretty well reproduces the results of autoclave gas phase charging.

  20. Application of nitrogen-alloyed martensitic stainless steels in the aviation industry

    SciTech Connect

    Stein, G.; Kirschner, W.; Lueg, J.

    1997-12-31

    Nitrogen in stainless martensitic steels has a beneficial influence on the mechanical as well as on the chemical properties. However the effect of nitrogen is limited due to the rather low solubility of this element. A special alloy development in combination with a pressurized melting technique lead to distinctly higher nitrogen contents. Stainless martensitic steels containing high nitrogen contents are manufactured by VSG today on an industrial scale using the PESR-process (Pressurized Electroslag Remelting). Depending on special applications these steels are available with different chemical analysis under the trademark CRONIDUR. The basic composition of all CRONIDUR-alloys consists of about 15% Chromium, 1% Molybdenum, 0.15 to 0.35% Carbon and 0.20 to 0.40% Nitrogen. The combination of Cr + Mo + N leads to a superior corrosion resistance of these HNS-steels (HNS: High Nitrogen Steels) in comparison to similar carbon based alloys. Focused on applications with a required minimum hardness of 58 HRC, like stainless bearings or screw shafts, the C+N-content is tuned between 0.60 and 0.80% (Brand: CRONIDUR 30). Additions of max. 0.3% Vanadium and 0.1% Niobium qualifies the brand CRONIDUR 20 for enhanced temperature applications like turbine disks or blades.

  1. Irradiation response of delta ferrite in as-cast and thermally aged cast stainless steel

    NASA Astrophysics Data System (ADS)

    Li, Zhangbo; Lo, Wei-Yang; Chen, Yiren; Pakarinen, Janne; Wu, Yaqiao; Allen, Todd; Yang, Yong

    2015-11-01

    To enable the life extension of Light Water Reactors (LWRs) beyond 60 years, it is critical to gain adequate knowledge for making conclusive predictions to assure the integrity of duplex stainless steel reactor components, e.g. primary pressure boundary and reactor vessel internal. Microstructural changes in the ferrite of thermally aged, neutron irradiated only, and neutron irradiated after being thermally aged cast austenitic stainless steels (CASS) were investigated using atom probe tomography. The thermal aging was performed at 400 °C for 10,000 h and the irradiation was conducted in the Halden reactor at ∼315 °C to 0.08 dpa (5.6 × 1019 n/cm2, E > 1 MeV). Low dose neutron irradiation at a dose rate of 5 × 10-9 dpa/s was found to induce spinodal decomposition in the ferrite of as-cast microstructure, and further to enhance the spinodal decomposition in the thermally aged cast alloys. Regarding the G-phase precipitates, the neutron irradiation dramatically increases the precipitate size, and alters the composition of the precipitates with increased, Mn, Ni, Si and Mo and reduced Fe and Cr contents. The results have shown that low dose neutron irradiation can further accelerate the degradation of ferrite in a duplex stainless steel at the LWR relevant condition.

  2. Superplastic forming of stainless steel automotive components

    SciTech Connect

    Bridges, B.; Elmer, J.; Carol, L.

    1997-02-06

    Exhaust emission standards are governmentally controlled standards, which are increasingly stringent, forcing alternate strategies to meet these standards. One approach to improve the efficiency of the exhaust emission equipment is to decrease the time required to get the catalytic converter to optimum operating temperature. To accomplish this, automotive manufacturers are using double wall stainless steel exhaust manifolds to reduce heat loss of the exhaust gases to the converter. The current method to manufacture double wall stainless steel exhaust components is to use a low-cost alloy with good forming properties and extensively form, cut, assemble, and weld the pieces. Superplastic forming (SPF) technology along with alloy improvements has potential at making this process more cost effective. Lockheed Martin Energy Systems (LMES), Lawrence Livermore National Laboratory (LLNL) and USCAR Low Emission Partnership (LEP) worked under a Cooperative Research And Development Agreement (CRADA) to evaluate material properties, SPF behavior, and welding behavior of duplex stainless steel alloy for automotive component manufacturing. Battelle Pacific Northwest National Laboratory (PNNL) has a separate CRADA with the LEP to use SPF technology to manufacture a double wall stainless steel exhaust component. As a team these CRADAs developed and demonstrated a technical plan to accomplish making double wall stainless steel exhaust manifolds.

  3. Development of Alumina-Forming Austenitic Stainless Steels

    SciTech Connect

    Brady, Michael P; Yamamoto, Yukinori; Bei, Hongbin; Santella, Michael L; Maziasz, Philip J

    2009-01-01

    This paper presents the results of the continued development of creep-resistant, alumina-forming austenitic (AFA) stainless steel alloys, which exhibit a unique combination of excellent oxidation resistance via protective alumina (Al2O3) scale formation and high-temperature creep strength through the formation of stable nano-scale MC carbides and intermetallic precipitates. Efforts in fiscal year 2009 focused on the characterization and understanding of long-term oxidation resistance and tensile properties as a function of alloy composition and microstructure. Computational thermodynamic calculations of the austenitic matrix phase composition and the volume fraction of MC, B2-NiAl, and Fe2(Mo,Nb) base Laves phase precipitates were used to interpret oxidation behavior. Of particular interest was the enrichment of Cr in the austenitic matrix phase by additions of Nb, which aided the establishment and maintenance of alumina. Higher levels of Nb additions also increased the volume fraction of B2-NiAl precipitates, which served as an Al reservoir during long-term oxidation. Ageing studies of AFA alloys were conducted at 750 C for times up to 2000 h. Ageing resulted in near doubling of yield strength at room temperature after only 50 h at 750 C, with little further increase in yield strength out to 2000 h of ageing. Elongation was reduced on ageing; however, levels of 15-25% were retained at room temperature after 2000 h of total ageing.

  4. Evaluation of aging of cast stainless steel components

    SciTech Connect

    Chung, H.M.

    1991-02-01

    Cast stainless steel is used extensively in nuclear reactors for primary-pressure-boundary components such as primary coolant pipes, elbows, valves, pumps, and safe ends. These components are, however, susceptible to thermal aging embrittlement in light water reactors because of the segregation of Cr atoms from Fe and Ni by spinodal decomposition in ferrite and the precipitation of Cr-rich carbides on ferrite/austenite boundaries. A recent advance in understanding the aging kinetics is presented. Aging kinetics are strongly influenced by the synergistic effects of other metallurgical reactions that occur in parallel with spinodal decomposition, i.e., clustering of Ni, Mo, and Si solute atoms and the nucleation and growth of G-phase precipitates in the ferrite phase. A number of methods are outlined for estimating aging embrittlement under end-of-life of life-extension conditions, depending on several factors such as degree of permissible conservatism, availability of component archive material, and methods of estimating and verifying the activation energy of aging. 33 refs., 6 figs., 3 tabs.

  5. Laser beam surface melting of high alloy austenitic stainless steel

    SciTech Connect

    Woollin, P.

    1996-12-31

    The welding of high alloy austenitic stainless steels is generally accompanied by a substantial reduction in pitting corrosion resistance relative to the parent, due to microsegregation of Mo and Cr. This prevents the exploitation of the full potential of these steels. Processing to achieve remelting and rapid solidification offers a means of reducing microsegregation levels and improving corrosion resistance. Surface melting of parent UNS S31254 steel by laser beam has been demonstrated as a successful means of producing fine, as-solidified structures with pitting resistance similar to that of the parent, provided that an appropriate minimum beam travel speed is exceeded. The use of N{sub 2} laser trail gas increased the pitting resistance of the surface melted layer. Application of the technique to gas tungsten arc (GTA) melt runs has shown the ability to raise the pitting resistance significantly. Indeed, the use of optimized beam conditions, N{sub 2} trail gas and appropriate surface preparation prior to laser treatment increased the pitting resistance of GTA melt runs to a level approaching that of the parent material.

  6. Calculation of stress relaxation properties for type 422 stainless steel

    SciTech Connect

    Ellis, F.V.; Tordonato, S.

    2000-02-01

    Analytical life prediction methods are being developed for high-temperature turbine and valve studs/bolts. In order to validate the approach, the calculated results are compared to the results of uniaxial stress relaxation testing, bolt model testing, and service experience. Long time creep, creep-rupture, and stress relaxation tests were performed by the National Research Institute for Metals of Japan (NRIM) for 12 Cr-1 Mo-1 W-1/4V, Type 422 stainless steel bolting material, at 500, 550, and 600 C. Based on these results and limited tests for a service-exposed bolt, the creep behavior can be described using a two-parameter material model: {var_epsilon}/{var_epsilon}{sub r} = 1-(1-(t/t{sub r}){sup m+1}){sup {delta}} where {var_epsilon}{sub r} is the rupture strain, t{sub r} is the rupture time, and m and {delta} are material constants. For comparison with the measured uniaxial stress relaxation properties, the stress relaxation was calculated using the two-parameter creep equation and a strain-hardening flow rule. The rupture time data was correlated using time-temperature parameter methods. A power law was used for the rupture strain versus rupture time relationship at each temperature. The calculated stress versus time curves were in good agreement with the measured at all temperatures and for initial strain levels of 0.10, 0.15, 0.20, and 0.25%.

  7. Stress corrosion cracking on irradiated 316 stainless steel

    NASA Astrophysics Data System (ADS)

    Furutani, Gen; Nakajima, Nobuo; Konishi, Takao; Kodama, Mitsuhiro

    2001-02-01

    Tests on irradiation-assisted stress corrosion cracking (IASCC) were carried out by using cold-worked (CW) 316 stainless steel (SS) in-core flux thimble tubes which were irradiated up to 5×10 26 n/m 2 ( E>0.1 MeV) at 310°C in a Japanese PWR. Unirradiated thimble tube was also tested for comparison with irradiated tubes. Mechanical tests such as the tensile, hardness tests and metallographic observations were performed. The susceptibility to SCC was examined by the slow strain rate test (SSRT) under PWR primary water chemistry condition and compositional analysis on the grain boundary segregation was made. Significant changes in the mechanical properties due to irradiation such as a remarkable increase of strength and hardness, and a considerable reduction of elongation were seen. SSRT results revealed that the intergranular fracture ratio (%IGSCC) increased as dissolved hydrogen (DH) increased. In addition, SSRT results in argon gas atmosphere showed a small amount of intergranular cracking. The depletion of Fe, Cr, Mo and the enrichment of Ni and Si were observed in microchemical analyses on the grain boundary.

  8. Joining dissimilar stainless steels for pressure vessel components

    NASA Astrophysics Data System (ADS)

    Sun, Zheng; Han, Huai-Yue

    1994-03-01

    A series of studies was carried out to examine the weldability and properties of dissimilar steel joints between martensitic and austenitic stainless steels - F6NM (OCr13Ni4Mo) and AISI 347, respectively. Such joints are important parts in, e.g. the primary circuit of a pressurized water reactor (PWR). This kind of joint requires both good mechanical properties, corrosion resistance and a stable magnetic permeability besides good weldability. The weldability tests included weld thermal simulation of the martensitic steel for investigating the influence of weld thermal cycles and post-weld heat treatment (PWHT) on the mechanical properties of the heat-affected zone (HAZ); implant testing for examining the tendency for cold cracking of martensitic steel; rigid restraint testing for determining hot crack susceptibility of the multi-pass dissimilar steel joints. The joints were subjected to various mechanical tests including a tensile test, bending test and impact test at various temperatures, as well as slow strain-rate test for examining the stress corrosion cracking tendency in the simulated environment of a primary circuit of a PWR. The results of various tests indicated that the quality of the tube/tube joints is satisfactory for meeting all the design requirements.

  9. Casting Stainless-Steel Models Around Pressure Tubes

    NASA Technical Reports Server (NTRS)

    Vasquez, Peter; Micol, John R.

    1992-01-01

    Survivability of thin-wall stainless-steel tubing increased to nearly 100 percent. Improves state of art in pressure-model castings and reduces cost associated with machining complete model from stainless-steel blank.

  10. Synthesis and structural characterization of Mo-Ni-W oxide nanostructures.

    PubMed

    Paraguay-Delgado, F; Huirache-Acuña, R; Jose-Yacaman, M; Alonso-Nuñez, G

    2008-06-01

    In this work, we report the synthesis and characterization of Mo-Ni-W oxides. The precursor was prepared from an aqueous solution of ammonium heptamolibdate, ammonium metatungstate, and nickel nitrate with an atomic ratio of 1:1:1 (Mo:W:Ni). The solution was then transferred to a Teflon-lined stainless steel autoclave and heated to 200 degrees C and left at this temperature for 48 h. The resulting material was then washed and dried. The morphology and elemental composition were studied by scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy, and X-ray diffraction. The porosity was studied by the Brunauer, Emmett, and Teller method. The materials synthesized at 200 degrees C remained amorphous and had a specific surface area of 114 m2/g with pore size of 34 A. The average length was 1 microm and the average diameter was 60 nm. The crystalline phase of synthesized material corresponded to W0.4Mo0.6O3 and WO3. After annealing at 550 degrees C for two hours, the material was polycrystalline with a segregated structure of MoO3, WO3; NiMoO4 was observed. The sublimation of the molybdenum oxide was evident when annealed at 900 degrees C for two hours and finally two crystalline phases of material remained; roundish WO3 and elongated particles of NiWO4. PMID:18681035

  11. Structural and adhesional properties of thin MoO3 films prepared by laser coating

    NASA Astrophysics Data System (ADS)

    Mihalev, Mihail; Hardalov, Chavdar; Christov, Christo; Michailov, Michail; Ranguelov, Bogdan; Leiste, Harald

    2014-05-01

    Laser marking plays an important role in numerous technological applications because of its flexibility, fastness and versatility. The present study deals with the structural and adhesional properties of thin MO3 layers on stainless steel substrates prepared by a specific modification of the laser coating technology known as "laser bonding". This approach consists in the local laser sintering of an initially deposited proper powder material, which forms under laser irradiation a layer with a definite graphical and topological design. The coatings, prepared of only MoO3 powder irradiated by a CO2 laser beam, are well bonded to the substrate and exhibit diffusive light reflection. Through applying a variety of methods for surface structural analysis, as micro-indentation, XRD, micro-Raman and SEM, this study also provides detailed information about the coatings' chemical bonding and composition. Our results reveal a good adhesion to the steel due to the formation of an amorphous interface between the MoO3 and the substrate. This amorphous interface arises from a "quenching" process of the molten MoO3 acting both as an oxidant and flux. Depending on the laser beam's intensity, energy and scanning velocity, we also observed recrystallization in specific areas of the coatings. The present study contributes to the better understanding of the adhesion, wear-resistance and hardness of MoO3 coatings obtained by laser bonding.

  12. Influences of passivating elements on the corrosion and biocompatibility of super stainless steels.

    PubMed

    Yoo, Young-Ran; Jang, Soon-Geun; Oh, Keun-Taek; Kim, Jung-Gu; Kim, Young-Sik

    2008-08-01

    Biometals need high corrosion resistance since metallic implants in the body should be biocompatible and metal ion release should be minimized. In this work, we designed three kinds of super stainless steel and adjusted the alloying elements to obtain different microstructures. Super stainless steels contain larger amounts of Cr, Mo, W, and N than commercial alloys. These elements play a very important role in localized corrosion and, thus, their effects can be represented by the "pitting resistance equivalent number (PREN)." This work focused on the behavior which can arise when the bare surface of an implant in the body is exposed during walking, heavy exercise, and so on. Among the experimental alloys examined herein, Alloy Al and 316L stainless steels were mildly cytotoxic, whereas the other super austenitic, duplex, and ferritic stainless steels were noncytotoxic. This behavior is primarily related to the passive current and pitting resistance of the alloys. When the PREN value was increased, the passivation behavior in simulated body solution was totally different from that in acidic chloride solution and, thus, the Cr(2)O(3)/Cr(OH)(3) and [Metal oxide]/[Metal + Metal oxide] ratios of the passive film in the simulated body solution were larger than those in acidic chloride solution. Also, the critical current density in simulated body solution increased and, thus, active dissolution may induce metal ion release into the body when the PREN value and Ni content are increased. This behavior was closely related to the presence of EDTA in the simulated body solution. PMID:18161790

  13. Corrosion behavior of sensitized duplex stainless steel.

    PubMed

    Torres, F J; Panyayong, W; Rogers, W; Velasquez-Plata, D; Oshida, Y; Moore, B K

    1998-01-01

    The present work investigates the corrosion behavior of 2205 duplex stainless steel in 0.9% NaCl solution after various heat-treatments, and compares it to that of 316L austenitic stainless steel. Both stainless steels were heat-treated at 500, 650, and 800 degrees C in air for 1 h, followed by furnace cooling. Each heat-treated sample was examined for their microstructures and Vickers micro-hardness, and subjected to the X-ray diffraction for the phase identification. Using potentiostatic polarization method, each heat-treated sample was corrosion-tested in 37 degrees C 0.9% NaCl solution to estimate its corrosion rate. It was found that simulated sensitization showed an adverse influence on both steels, indicating that corrosion rates increased by increasing the sensitization temperatures. PMID:9713683

  14. Ultrasonic Spectroscopy of Stainless Steel Sandwich Panels

    NASA Technical Reports Server (NTRS)

    Cosgriff, Laura M.; Lerch, Bradley A.; Hebsur, Mohan G.; Baaklini, George Y.; Ghosn, Louis J.

    2003-01-01

    Enhanced, lightweight material systems, such as 17-4PH stainless steel sandwich panels are being developed for use as fan blades and fan containment material systems for next generation engines. In order to improve the production for these systems, nondestructive evaluation (NDE) techniques, such as ultrasonic spectroscopy, are being utilized to evaluate the brazing quality between the 17-4PH stainless steel face plates and the 17-4PH stainless steel foam core. Based on NDE data, shear tests are performed on sections representing various levels of brazing quality from an initial batch of these sandwich structures. Metallographic characterization of brazing is done to corroborate NDE findings and the observed shear failure mechanisms.

  15. Explosive Surface Hardening of Austenitic Stainless Steel

    NASA Astrophysics Data System (ADS)

    Kovacs-Coskun, T.

    2016-04-01

    In this study, the effects of explosion hardening on the microstructure and the hardness of austenitic stainless steel have been studied. The optimum explosion hardening technology of austenitic stainless steel was researched. In case of the explosive hardening used new idea mean indirect hardening setup. Austenitic stainless steels have high plasticity and can be easily cold formed. However, during cold processing the hardening phenomena always occurs. Upon the explosion impact, the deformation mechanism indicates a plastic deformation and this deformation induces a phase transformation (martensite). The explosion hardening enhances the mechanical properties of the material, includes the wear resistance and hardness. In case of indirect hardening as function of the setup parameters specifically the flayer plate position the hardening increased differently. It was find a relationship between the explosion hardening setup and the hardening level.

  16. Stainless Steel Microstructure and Mechanical Properties Evaluation

    SciTech Connect

    Switzner, Nathan T

    2010-06-01

    A nitrogen strengthened 21-6-9 stainless steel plate was spinformed into hemispherical test shapes. A battery of laboratory tests was used to characterize the hemispheres. The laboratory tests show that near the pole (axis) of a spinformed hemisphere the yield strength is the lowest because this area endures the least “cold-work” strengthening, i.e., the least deformation. The characterization indicated that stress-relief annealing spinformed stainless steel hemispheres does not degrade mechanical properties. Stress-relief annealing reduces residual stresses while maintaining relatively high mechanical properties. Full annealing completely eliminates residual stresses, but reduces yield strength by about 30%.

  17. Measuring secondary phases in duplex stainless steels

    NASA Astrophysics Data System (ADS)

    Calliari, I.; Brunelli, K.; Dabalà, M.; Ramous, E.

    2009-01-01

    The use of duplex stainless steels is limited by their susceptibility to the formation of dangerous intermetallic phases resulting in detrimental effects on impact toughness and corrosion resistance. This precipitation and the quantitative determinations of the phases have received considerable attention and different precipitation sequences (σ phase, χ phase, and carbides) have been suggested. This study investigates the phase transformation during continuous cooling and isothermal treatments in commercial duplex stainless steel grades and the effects on alloy properties, and compares the most common techniques of analysis.

  18. Embrittlement of austenitic stainless steel welds

    SciTech Connect

    David, S.A.; Vitek, J.M.; Alexander, D.J.

    1995-06-01

    To prevent hot-cracking, austenitic stainless steel welds generally contain a small percent of delta ferrite. Although ferrite has been found to effectively prevent hot-cracking, it can lead to embrittlement of welds when exposed to elevated temperatures. The aging behavior of type-308 stainless steel weld has been examined over a range of temperatures 475--850 C for times up to 10,000 hrs. Upon aging, and depending on the temperature range, the unstable ferrite may undergo a variety of solid state transformations. These phase changes creep-rupture and Charpy impact properties.

  19. Development of Low-Cost Austenitic Stainless Gas-Turbine and Diesel Engine Components with Enhanced High-Temperature Reliability

    SciTech Connect

    Maziasz, P.J.; Swindeman, R.W.; Browning, P.F.; Frary, M.E.; Pollard, M.J.; Siebenaler, C.W.; McGreevy, T.E.

    2004-06-01

    In July of 1999, a Cooperative Research and Development Agreement (CRADA) was undertaken between Oak Ridge National Laboratory (ORNL) and Solar Turbines, Inc. and Caterpillar, Inc. (Caterpillar Technical Center) to evaluate commercial cast stainless steels for gas turbine engine and diesel engine exhaust component applications relative to the materials currently being used. If appropriate, the goal was to develop cast stainless steels with improved performance and reliability rather than switch to more costly cast Ni-based superalloys for upgraded performance. The gas-turbine components considered for the Mercury-50 engine were the combustor housing and end-cover, and the center-frame hot-plate, both made from commercial CF8C cast austenitic stainless steel (Fe-l9Cr-12Ni-Nb,C), which is generally limited to use at below 650 C. The advanced diesel engine components considered for truck applications (C10, C12, 3300 and 3400) were the exhaust manifold and turbocharger housing made from commercial high SiMo ductile cast iron with uses limited to 700-750 C or below. Shortly after the start of the CRADA, the turbine materials emphasis changed to wrought 347H stainless steel (hot-plate) and after some initial baseline tensile and creep testing, it was confirmed that this material was typical of those comprising the abundant database; and by 2000, the emphasis of the CRADA was primarily on diesel engine materials. For the diesel applications, commercial SiMo cast iron and standard cast CN12 austenitic stainless steel (Fe-25Cr-13Ni-Nb,C,N,S) baseline materials were obtained commercially. Tensile and creep testing from room temperature to 900 C showed the CN12 austenitic stainless steel to have far superior strength compared to SiMo cast iron above 550 C, together with outstanding oxidation resistance. However, aging at 850 C reduced room-temperature ductility of the standard CN12, and creep-rupture resistance at 850 C was less than expected, which triggered a focused

  20. 21 CFR 872.3350 - Gold or stainless steel cusp.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Gold or stainless steel cusp. 872.3350 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3350 Gold or stainless steel cusp. (a) Identification. A gold or stainless steel cusp is a prefabricated device made of austenitic alloys or...

  1. 21 CFR 872.3350 - Gold or stainless steel cusp.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Gold or stainless steel cusp. 872.3350 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3350 Gold or stainless steel cusp. (a) Identification. A gold or stainless steel cusp is a prefabricated device made of austenitic alloys or...

  2. 21 CFR 872.3350 - Gold or stainless steel cusp.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Gold or stainless steel cusp. 872.3350 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3350 Gold or stainless steel cusp. (a) Identification. A gold or stainless steel cusp is a prefabricated device made of austenitic alloys or...

  3. 21 CFR 878.4495 - Stainless steel suture.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Stainless steel suture. 878.4495 Section 878.4495...) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4495 Stainless steel suture. (a) Identification. A stainless steel suture is a needled or unneedled nonabsorbable surgical suture composed of...

  4. 21 CFR 878.4495 - Stainless steel suture.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Stainless steel suture. 878.4495 Section 878.4495...) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4495 Stainless steel suture. (a) Identification. A stainless steel suture is a needled or unneedled nonabsorbable surgical suture composed of...

  5. 21 CFR 878.4495 - Stainless steel suture.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Stainless steel suture. 878.4495 Section 878.4495...) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4495 Stainless steel suture. (a) Identification. A stainless steel suture is a needled or unneedled nonabsorbable surgical suture composed of...

  6. 21 CFR 878.4495 - Stainless steel suture.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Stainless steel suture. 878.4495 Section 878.4495...) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4495 Stainless steel suture. (a) Identification. A stainless steel suture is a needled or unneedled nonabsorbable surgical suture composed of...

  7. 21 CFR 878.4495 - Stainless steel suture.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Stainless steel suture. 878.4495 Section 878.4495...) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4495 Stainless steel suture. (a) Identification. A stainless steel suture is a needled or unneedled nonabsorbable surgical suture composed of...

  8. 21 CFR 872.3350 - Gold or stainless steel cusp.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Gold or stainless steel cusp. 872.3350 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3350 Gold or stainless steel cusp. (a) Identification. A gold or stainless steel cusp is a prefabricated device made of austenitic alloys or...

  9. 21 CFR 872.3350 - Gold or stainless steel cusp.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Gold or stainless steel cusp. 872.3350 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3350 Gold or stainless steel cusp. (a) Identification. A gold or stainless steel cusp is a prefabricated device made of austenitic alloys or...

  10. Isothermal formation of martensite in a 12Cr-9Ni-4Mo maraging stainless steel

    SciTech Connect

    Holmquist, M.

    1995-11-01

    The present paper is concerned with the nature of the martensite, which provides the basis for the maraging treatment. Rather than forming martensite during cooling, 1RK91 develops martensite when held at a constant temperature in a range from room temperature and below. Isothermal martensite formation showing C-curve kinetics was found to occur in the maraging steel 1RK91, the nose temperature being about {minus}40 C. The kinetics was found to be enhanced for higher austenitizing treatment temperatures, presumably through a combination of larger grain size and a larger number of quenched in nuclei for isothermal martensite transformation. Experiments involving different cooling rates showed that fast cooling enhanced the transformation kinetics. Based on this observation it is suggested that quenched-in vacancy clusters provide suitable strain embryos for isothermal martensite nucleation.

  11. Synthesis and characterization of porous Mo-W oxide nanostructures.

    PubMed

    Paraguay-Delgado, F; Verde, Y; Cizniega, E; Lumbreras, J A; Alonso-Nuñez, G

    2008-12-01

    The present study reports the synthesis method, microstructure characterization, and thermal stability of nanostructured porous mixed oxide (MoO3-WO3) at 550 and 900 degrees C of annealing. The material was synthesized using a hydrothermal method. The precursor was prepared by aqueous solution using ammonium heptamolibdate and ammonium metatungstate, with an atomic ratio of Mo/W = 1. The pH was adjusted to 5, and then the solution was transferred to a teflon-lined stainless steel autoclave and heated at 200 degrees C for 48 h. The resultant material was washed using deionized water. The specific surface area, morphology, composition, and microstructure before and after annealing were studied by N2 physisorption, scanning electron microscopy (SEM), analytical transmission electron microscopy (TEM), and X-Ray diffraction (XRD). The initial synthesized materials showed low crystallinity and high specific surface area around (141 m2/g). After thermal annealing the material showed higher crystallinity and diminished its specific surface area drastically. PMID:19205219

  12. Clean cast steel technology. Determination of transformation diagrams for duplex stainless steel

    SciTech Connect

    Chumbley, S. L.

    2005-09-01

    Duplex stainless steels (DSS) constitute both ferrite and austenite as a matrix. Such a microstructure confers a high corrosion resistance with favorable mechanical properties. However, intermetallic phases such as sigma ( can also form during casting or high-temperature processing and can degrade the properties of the DSS. This research was initiated to develop time-temperature-transformation (TTT) and continuous-cooling- transformation (CCT) diagrams of two types of cast duplex stainless steels, CD3MN (Fe 22Cr-5Ni-Mo-N) and CD3MWCuN (Fe-25Cr-7Ni-Mo-W-Cu-N), in order to understand the time and temperature ranges for intermetallic phase formation. The alloys were heat treated isothermally or under controlled cooling conditions and then characterized using conventional metallographic methods that included tint etching, and also using electron microscopy (SEM, TEM) and wavelength dispersive spectroscopy (WDS). The kinetics of intermetallic-phase ( formation were analyzed using the Johnson-Mehl-Avrami (JMA) equation in the case of isothermal transformations and a modified form of this equation in the case of continuous cooling transformations, The rate of intermetallic-phase formation was found to be much faster in CD3MWCuN than CD3MN due mainly to differences in the major alloying contents such as Cr, Ni and Mo. To examine in more detail the effects of these elements of the phase stabilities, a series of eight steel castings was designed with the Cr, Ni and Mo contents systematically varied with respect to the nominal composition of CD3MN. The effects of varying the contents of alloying additions on the formation of intermetallic phases were also studied computationally using the commercial thermodynamic software package, Thermo-Calc. In general, was stabilized with increasing Cr addition and by increasing Mo addition. However, a delicate balance among Ni and other minor elements such as N and Si also exists. Phase equilibria in DSS can be affected by local

  13. Carbon diffusion and phase transformations during gas carburizing of high-alloyed stainless steels: Experimental study and theoretical modeling

    NASA Astrophysics Data System (ADS)

    Turpin, T.; Dulcy, J.; Gantois, M.

    2005-10-01

    Gas carburizing of high-alloyed stainless steels increases surface hardness, as well as the overall mechanical characteristics of the surface. The growth of chromium-rich carbides during carbon transfer into the steel causes precipitation hardening in the surface, but decreases the chromium content in solid solution. In order to maintain a good corrosion resistance in the carburized layer, the stainless steel composition and the carburizing process need to be optimized. To limit the experimental work, a methodology using software for modeling the thermodynamic and kinetic properties in order to simulate carbon diffusion and phase transformations during gas carburizing is presented. Thermodynamic calculations are initially used to find the optimum parameters ( T, carbon wt pct, etc.) in order to maintain the highest Cr and Mo contents in the austenitic solid solution. In a second step, kinetic calculations using the diffusion-controlled transformations (DICTRA) software are used to predict how the amount of the different phases varies and how the carbon profile in the steel changes as a function of time during the process. Experimental carbon profiles were determined using a wavelength-dispersive spectrometer for electron-probe microanalysis (WDS-EPMA), while carbide compositions were measured by energy-dispersive spectroscopy_X (EDS_X) analyses. A good agreement between calculated and experimental values was observed for the Fe-13Cr-5Co-3Ni-2Mo-0.07C and the Fe-12Cr-2Ni-2Mo-0.12C (wt pct) martensitic stainless steels at 955 °C and 980 °C.

  14. Atom probe tomography investigation of lath boundary segregation and precipitation in a maraging stainless steel.

    PubMed

    Thuvander, Mattias; Andersson, Marcus; Stiller, Krystyna

    2013-09-01

    Lath boundaries in a maraging stainless steel of composition 13Cr-8Ni-2Mo-2Cu-1Ti-0.7Al-0.3Mn-0.2Si-0.03C (at%) have been investigated using atom probe tomography following aging at 475 °C for up to 100 h. Segregation of Mo, Si and P to the lath boundaries was observed already after 5 min of aging, and the amount of segregation increases with aging time. At lath boundaries also precipitation of η-Ni₃(Ti, Al) and Cu-rich 9R, in contact with each other, takes place. These co-precipitates grow with time and because of coarsening the area number density decreases. After 100 h of aging a ∼5 nm thick film-like precipitation of a Mo-rich phase was observed at the lath boundaries. From the composition of the film it is suggested that the phase in question is the quasicrystalline R' phase. The film is perforated with Cu-rich 9R and η-Ni₃(Ti, Al) co-precipitates. Not all precipitate types present in the matrix do precipitate at the lath boundaries; the Si-containing G phase and γ'-Ni₃(Ti, Al, Si) and the Cr-rich α' phase were not observed at the lath boundaries. PMID:23234833

  15. Irradiation-induced microchemical changes in highly irradiated 316 stainless steel

    NASA Astrophysics Data System (ADS)

    Fujii, K.; Fukuya, K.

    2016-02-01

    Cold-worked 316 stainless steel specimens irradiated to 74 dpa in a pressurized water reactor (PWR) were analyzed by atom probe tomography (APT) to extend knowledge of solute clusters and segregation at higher doses. The analyses confirmed that those clusters mainly enriched in Ni-Si or Ni-Si-Mn were formed at high number density. The clusters were divided into three types based on their size and Mn content; small Ni-Si clusters (3-4 nm in diameter), and large Ni-Si and Ni-Si-Mn clusters (8-10 nm in diameter). The total cluster number density was 7.7 × 1023 m-3. The fraction of large clusters was almost 1/10 of the total density. The average composition (in at%) for small clusters was: Fe, 54; Cr, 12; Mn, 1; Ni, 22; Si, 11; Mo, 1, and for large clusters it was: Fe, 44; Cr, 9; Mn, 2; Ni, 29; Si, 14; Mo,1. It was likely that some of the Ni-Si clusters correspond to γ‧ phase precipitates while the Ni-Si-Mn clusters were precursors of G phase precipitates. The APT analyses at grain boundaries confirmed enrichment of Ni, Si, P and Cu and depletion of Fe, Cr, Mo and Mn. The segregation behavior was consistent with previous knowledge of radiation induced segregation.

  16. ASTM update for stainless steels II

    SciTech Connect

    Davison, R.M.

    1999-10-01

    Specifiers and users of stainless steel (SS) should be aware that the American Society for Testing and Materials (ASTM) has revised several of its SS specifications. These changes affect grades commonly used in process and other industries. These changes are discussed.

  17. Forming "dynamic" membranes on stainless steel

    NASA Technical Reports Server (NTRS)

    Brandon, C. A.; Gaddis, J. L.

    1979-01-01

    "Dynamic" zirconium polyacrylic membrane is formed directly on stainless steel substrate without excessive corrosion of steel. Membrane is potentially useful in removal of contaminated chemicals from solution through reversed osmosis. Application includes use in filtration and desalination equipment, and in textile industry for separation of dyes from aqueous solvents.

  18. Proof Testing Of Stainless-Steel Bolts

    NASA Technical Reports Server (NTRS)

    Hsieh, Cheng H.; Hendrickson, James A.; Bamford, Robert M.

    1992-01-01

    Report describes study of development of method for nondestructive proof testing of bolts made of A286 stainless steel. Based on concept that the higher load bolt survives, the smaller the largest flaw and, therefore, the longer its fatigue life after test. Calculations and experiments increase confidence in nondestructive proof tests.

  19. Austenitic stainless steels for cryogenic service

    SciTech Connect

    Dalder, E.N.C.; Juhas, M.C.

    1985-09-19

    Presently available information on austenitic Fe-Cr-Ni stainless steel plate, welds, and castings for service below 77 K are reviewed with the intent (1) of developing systematic relationships between mechanical properties, composition, microstructure, and processing, and (2) of assessing the adequacy of these data bases in the design, fabrication, and operation of engineering systems at 4 K.

  20. Materials data handbooks on stainless steels

    NASA Technical Reports Server (NTRS)

    Muraca, R. F.; Whittick, J. S.

    1973-01-01

    Two handbooks which summarize latest available data have been published. Two types of stainless steels, alloy A-286 and Type 301, are described. Each handbook is divided into twelve chapters. Scope of information presented includes physical- and mechanical-property data at cryogenic, ambient, and elevated temperatures.

  1. Materials data handbook: Stainless steel type 301

    NASA Technical Reports Server (NTRS)

    Muraca, R. F.; Whittick, J. S.

    1972-01-01

    A summary of the materials property information for stainless steel type 301 is presented. The scope of the information includes physical and mechanical properties at cryogenic, ambient, and elevated temperatures. Information on material procurement, metallurgy of the alloy, corrosion, environmental effects, fabrication, and bonding is developed.

  2. Optimizing surface quality of stainless alloys and using a modified ASTM G 48B procedure for acceptance testing

    SciTech Connect

    Maurer, J.R.

    1999-01-01

    The formation of high-temperature oxide scales and Cr-depleted zones on stainless alloys, such as 6% Mo superaustenitic steels, can significantly reduce their corrosion resistance. Effective methods to remove these layers and restore the surface to an optimized condition are detailed. Also, an acceptance test using a modified ASTM G 48B method at 35 C (95 F) for 72 h with a specimen having a crevice, and special corrosion criteria for failure, are described. Comparison of this test method with one using an uncreviced specimen at lower temperatures and for less time is discussed.

  3. Mo-Si-B Alloy Development

    SciTech Connect

    Schneibel, Joachim H; Brady, Michael P; Meyer III, Harry M; Horton Jr, Joe A; Kruzic, JJ; Ritchie, R O

    2005-01-01

    Mo-Si-B silicides consisting of the phases {alpha}-Mo (Mo solid solution), Mo{sub 3}Si, and Mo{sub 5}SiB{sub 2} have melting points on the order of 2000 C and have potential as ultra-high temperature structural materials. Mo-Si-B alloys can be processed such that the {alpha}-Mo is present in the form of isolated particles in a silicide matrix, or as a continuous matrix 'cementing' individual silicide particles together. The latter microstructure is similar to that of WC-Co hard metals. This paper focuses on the relationship between the topology as well as scale of the microstructure of Mo-Mo{sub 3}Si-Mo{sub 5}SiB{sub 2} alloys, and their creep strength and fracture toughness. For example, the creep strength of Mo-Si-B alloys is improved by reducing the {alpha}-Mo volume fraction and by making the {alpha}-Mo phase discontinuous. The fracture toughness is improved by increasing the {alpha}-Mo volume fraction and by making the {alpha}-Mo phase continuous. Room temperature stress intensity factors as high as 21 MPa m{sup 1/2} were obtained. The room temperature fracture toughness of Mo-Si-B alloys can also be improved by microalloying with Zr. The room temperature ductility of Mo itself can be improved by adding MgAl{sub 2}O{sub 4} spinel particles suggesting yet another way to improve the ductile phase toughening of Mo-Si-B alloys.

  4. Mo-Si-B Alloy Development

    SciTech Connect

    Schneibel, J.H.; Kruzie, J.J.; Ritchie, R.O.

    2003-04-24

    Mo-Si-B silicides consisting of the phases {alpha}-Mo (Mo solid solution), Mo{sub 3}Si, and Mo{sub 5}SiB{sub 2} have melting points on the order of 2000 C and have potential as ultra-high temperature structural materials. Mo-Si-B alloys can be processed such that the {alpha}-Mo is present in the form of isolated particles in a silicide matrix, or as a continuous matrix ''cementing'' individual silicide particles together. The latter microstructure is similar to that of WC-Co hard metals. This paper focuses on the relationship between the topology as well as scale of the microstructure of Mo-Mo{sub 3}Si-Mo{sub 5}SiB{sub 2} alloys, and their creep strength and fracture toughness. For example, the creep strength of Mo-Si-B alloys is improved by reducing the {alpha}-Mo volume fraction and by making the {alpha}-Mo phase discontinuous. The fracture toughness is improved by increasing the {alpha}-Mo volume fraction and by making the {alpha}-Mo phase continuous. Room temperature stress intensity factors as high as 21 MPa m{sup 1/2} were obtained. The room temperature fracture toughness of Mo-Si-B alloys can also be improved by microalloying with Zr. The room temperature ductility of Mo itself can be improved by adding MgAl{sub 2}O{sub 4} spinel particles suggesting yet another way to improve the ductile phase toughening of Mo-Si-B alloys.

  5. Review of time-dependent fatigue behavior and life prediction for 2 1/4 Cr-1 Mo steel. [LMFBR

    SciTech Connect

    Booker, M.K.; Majumdar, S.

    1982-01-01

    Available data on creep-fatigue life and fracture behavior of 2 1/4 Cr-1 Mo steel are reviewed. Whereas creep-fatigue interaction is important for Type 304 stainless steel, oxidation effects appear to dominate the time-dependent fatigue behavior of 2 1/4 Cr-1 Mo steel. Four of the currently available predictive methods - the Linear Damage Rule, Frequency Separation Equation, Strain Range Partitioning Equation, and Damage Rate Equation - are evaluated for their predictive capability. Variations in the parameters for the various predictive methods with temperature, heat of material, heat treatment, and environment are investigated. Relative trends in the lives predicted by the various methods as functions of test duration, waveshape, etc., are discussed. The predictive methods will need modification in order to account for oxidation and aging effects in the 2 1/4 Cr-1 Mo steel. Future tests that will emphasize the difference between the various predictive methods are proposed.

  6. Mo-Si alloy development

    SciTech Connect

    Liu, C.T.; Heatherly, L.; Wright, J.L.

    1996-06-01

    The objective of this task is to develop new-generation corrosion-resistant Mo-Si intermetallic alloys as hot components in advanced fossil energy conversion and combustion systems. The initial effort is devoted to Mo{sub 5}-Si{sub 3}-base (MSB) alloys containing boron additions. Three MSB alloys based on Mo-10.5Si-1.1B (wt %), weighing 1500 g were prepared by hot pressing of elemental and alloy powders at temperatures to 1600{degrees}C in vacuum. Microporosities and glassy-phase (probably silicate phases) formations are identified as the major concerns for preparation of MSB alloys by powder metallurgy. Suggestions are made to alleviate the problems of material processing.

  7. Microstructure and mechanical properties of as-cast Ti-Mo-xCr alloy for biomedical application

    NASA Astrophysics Data System (ADS)

    Senopati, Galih; Sutowo, Cahya; P. A., I. Nyoman Gede; Utomo, Edy Priyanto; Amal, M. Ikhlasul

    2016-02-01

    Beta Ti alloys is one of the most attractive biomaterials due to their better corrosion resistance, biocompatibility, greater specific strength and lower elastic modulus than stainless steels and Co-Cr based alloys. Cr is the strong beta Ti stabilizer and has lower density than Nb, Sn and Ta. In this study As cast Ti-12Mo and Ti-12-xCr with Cr content range 1, 3, 5, and 10 wt.% prepared by using arc melting vacuum-pressure casting were investigated. The as cast Ti-Mo and Ti-Mo-xCr examined using X-ray diffraction (XRD), optical microscope (OM) and Vickers hardness tester. Experimental result indicate Ti-12Mo-xNb match for β phase peaks but TiO2 phase occurred in all alloys. The vickers hardness values of all the Ti-12Mo-xCr alloys are higher than HV 1000. The optical microscope investigation indicate Cr content influence Ti-Mo-xCr microstructure.

  8. Fermiology of Cr and Mo

    NASA Astrophysics Data System (ADS)

    Dugdale, S. B.; Fretwell, H. M.; Hedley, D. C. R.; Alam, M. A.; Jarlborg, T.; Santi, G.; Singru, R. M.; Sundararajan, V.; Cooper, M. J.

    1998-11-01

    An interpretation of the two-dimensional angular correlation of positron annihilation radiation (2D-ACAR) for paramagnetic chromium (Cr) and molybdenum (Mo) is presented. Rather than explaining the significant differences in the resulting k-space occupancies in terms of different Fermi surface (FS) topologies, the recovery of a FS topology for paramagnetic Cr in agreement with band theory (and similar to the Mo experiment) through the application of a recently introduced maximum-entropy-based filtering technique suggests an explanation related to positron wavefunction perturbations.

  9. Computer Series, 114: MO Theory Made Visible.

    ERIC Educational Resources Information Center

    Mealli, Carlo; Proserpio, Davide M.

    1990-01-01

    A collection of Molecular Orbital (MO) programs that have been integrated into routines and programs to illustrate MO theory are presented. Included are discussions of Computer Aided Composition of Atomic Orbitals (CACAO) and Walsh diagrams. (CW)

  10. Compaction and Sintering of Mo Powders

    SciTech Connect

    Nunn, Stephen D; Kiggans, Jim; Bryan, Chris

    2013-01-01

    To support the development of Mo-99 production by NorthStar Medical Technologies, LLC, Mo metal powders were evaluated for compaction and sintering characteristics as they relate to Mo-100 accelerator target disk fabrication. Powders having a natural isotope distribution and enriched Mo-100 powder were examined. Various powder characteristics are shown to have an effect on both the compaction and sintering behavior. Natural Mo powders could be cold pressed directly to >90% density. All of the powders, including the Mo-100 samples, could be sintered after cold pressing to >90% density. As an example, a compacted Mo-100 disk reached 89.7% density (9.52 g/cm3) after sintering at 1000 C for 1 hr. in flowing Ar/4%H2. Higher sintering temperatures were required for other powder samples. The relationships between processing conditions and the resulting densities of consolidated Mo disks will be presented.

  11. A Simple MO Treatment of Metal Clusters.

    ERIC Educational Resources Information Center

    Sahyun, M. R. V.

    1980-01-01

    Illustrates how a qualitative description of the geometry and electronic characteristics of homogeneous metal clusters can be obtained using semiempirical MO (molecular orbital theory) methods. Computer applications of MO methods to inorganic systems are also described. (CS)

  12. Optimization of the Processing of Mo Disks

    SciTech Connect

    Tkac, Peter; Rotsch, David A.; Stepinski, Dominique; Makarashvili, Vakhtang; Harvey, James; Vandegrift, George F.

    2016-01-01

    The objective of this work is to decrease the processing time for irradiated disks of enriched Mo for the production of 99Mo. Results are given for the dissolution of nonirradiated Mo disks, optimization of the process for large-scale dissolution of sintered disks, optimization of the removal of the main side products (Zr and Nb) from dissolved targets, and dissolution of irradiated Mo disks.

  13. Thermal aging modeling and validation on the Mo containing Fe-Cr-Ni alloys

    SciTech Connect

    Yang, Ying; Tan, Lizhen; Busby, Jeremy T.

    2015-04-01

    Thermodynamics of intermetallic phases in Fe-rich Fe-Cr-Ni-Mo alloys is critical knowledge to understand thermal aging effect on the phase stability of Mo-containing austenitic steels, which subsequently facilitates alloy design/improvement and degradation mitigation of these materials for reactor applications. Among the intermetallic phases, Chi (χ), Laves, and Sigma (σ) are often of concern because of their tendency to cause embrittlement of the materials. The focus of this study is thermal stability of the Chi and Laves phases as they were less studied compared to the Sigma phase. Coupled with thermodynamic modeling, thermal stability of intermetallic phases in Mo containing Fe-Cr-Ni alloys was investigated at 1000, 850 and 700 C for different annealing times. The morphologies, compositions and crystal structures of the precipitates of the intermetallic phases were carefully examined by scanning electron microscopy, electron probe microanalysis, X-ray diffraction, and transmission electron microscopy. Three key findings resulted from this study. First, the Chi phase is stable at high temperature, and with decreasing temperature it transforms into the Laves phase that is stable at low temperature. Secondly, Cr, Mo, Ni are soluble in both the Chi and Laves phases, with the solubility of Mo playing a major role in the relative stability of the intermetallic phases. Thirdly, in situ transformation from Chi phase to Laves phase was directly observed, which increased the local strain field, generated dislocations in the intermetallic phases, and altered the precipitate phase orientation relationship with the austenitic matrix. The thermodynamic models that were developed and validated were then applied to evaluating the effect of Mo on the thermal stability of intermetallic phases in type 316 and NF709 stainless steels.

  14. Phase Transformation in Cast Superaustenitic Stainless Steels

    SciTech Connect

    Nathaniel Steven Lee Phillips

    2006-12-12

    Superaustenitic stainless steels constitute a group of Fe-based alloys that are compositionally balanced to have a purely austenitic matrix and exhibit favorable pitting and crevice corrosion resistant properties and mechanical strength. However, intermetallic precipitates such as sigma and Laves can form during casting or exposure to high-temperature processing, which degrade the corrosion and mechanical properties of the material. The goal of this study was to accurately characterize the solid-solid phase transformations seen in cast superaustenitic stainless steels. Heat treatments were performed to understand the time and temperature ranges for intermetallic phase formations in alloys CN3MN and CK3MCuN. Microstructures were characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy and wavelength dispersive spectroscopy (EDS, WDS). The equilibrium microstructures, composed primarily of sigma and Laves within purely austenitic matrices, showed slow transformation kinetics. Factors that determine the extent of transformation, including diffusion, nucleation, and growth, are discussed.

  15. Formability of type 304 stainless steel sheet

    SciTech Connect

    Coubrough, G.J.; Matlock, D.K.; VanTyne, C.J.

    1992-09-01

    Punch-stretch tests to determine formability of type 304 stainless steel sheet were conducted using a hemispherical dome test. Sheets of 19.1 mm width and 177.8 mm width were stretched on a 101.6 mm diameter punch at punch rates between 0.042 to 2.12 mm/s with three lubricant systems: a mineral seal oil, thin polytetrafluoroethelyne sheet with mineral seal oil, and silicone rubber with mineral seal oil. The resulting strain distributions were measured and the amount of martensite was determined by magnetic means. Increasing lubricity resulted in more uniform strain distributions while increased punch rates tended to decrease both strain and transformation distributions. High forming limit values were related to the formation of high and uniformly distributed martensite volume fractions during deformation. The results of this study are interpreted with an analysis of the effects of strain and temperature on strain induced martensite formation in metastable austenitic stainless steels.

  16. Formability of type 304 stainless steel sheet

    SciTech Connect

    Coubrough, G.J. . Rocky Flats Plant); Matlock, D.K.; VanTyne, C.J. )

    1992-01-01

    Punch-stretch tests to determine formability of type 304 stainless steel sheet were conducted using a hemispherical dome test. Sheets of 19.1 mm width and 177.8 mm width were stretched on a 101.6 mm diameter punch at punch rates between 0.042 to 2.12 mm/s with three lubricant systems: a mineral seal oil, thin polytetrafluoroethelyne sheet with mineral seal oil, and silicone rubber with mineral seal oil. The resulting strain distributions were measured and the amount of martensite was determined by magnetic means. Increasing lubricity resulted in more uniform strain distributions while increased punch rates tended to decrease both strain and transformation distributions. High forming limit values were related to the formation of high and uniformly distributed martensite volume fractions during deformation. The results of this study are interpreted with an analysis of the effects of strain and temperature on strain induced martensite formation in metastable austenitic stainless steels.

  17. Tritium Depth Profiles in 316 Stainless Steel

    NASA Astrophysics Data System (ADS)

    Torikai, Yuji; Murata, Daiju; Penzhorn, Ralf-Dieter; Akaishi, Kenya; Watanabe, Kuniaki; Matsuyama, Masao

    To investigate the behavior of hydrogen uptake and release by 316 stainless steel (SS316), as-received and finely polished stainless steel specimens were exposed at 573 K to tritium gas diluted with hydrogen. Then tritium concentration in the exposed specimens was measured as a function of depth using a chemical etching method. All the tritium concentration profiles showed a sharp drop in the range of 10 μm from the top surface up to the bulk. The amount of tritium absorbed into the polished specimens was three times larger than that into the as-received specimen. However, the polishing effects disappeared by exposing to the air for a long time.

  18. Decomposition and Precipitation Process During Thermo-mechanical Fatigue of Duplex Stainless Steel

    NASA Astrophysics Data System (ADS)

    Weidner, Anja; Kolmorgen, Roman; Kubena, Ivo; Kulawinski, Dirk; Kruml, Tomas; Biermann, Horst

    2016-05-01

    The so-called 748 K (475 °C) embrittlement is one of the main drawbacks for the application of ferritic-austenitic duplex stainless steels (DSS) at higher temperatures caused by a spinodal decomposition of the ferritic phase. Thermo-mechanical fatigue tests performed on a DSS in the temperature range between 623 K and 873 K (350 °C and 600 °C) revealed no negative influence on the fatigue lifetime. However, an intensive subgrain formation occurred in the ferritic phase, which was accompanied by formation of fine precipitates. In order to study the decomposition process of the ferritic grains due to TMF testing, detailed investigations using scanning and transmission electron microscopy are presented. The nature of the precipitates was determined as the cubic face centered G-phase, which is characterized by an enrichment of Si, Mo, and Ni. Furthermore, the formation of secondary austenite within ferritic grains was observed.

  19. Cavitation Erosion Characteristics of Nitrocarburized and HPDL-Treated Martensitic Stainless Steels

    NASA Astrophysics Data System (ADS)

    Pant, B. K.; Arya, Vivek; Mann, B. S.

    2012-06-01

    This article deals with plasma ion-nitrocarburising and high power diode laser (HPDL) surface treatment of 13Cr4Ni and X10CrNiMoV1222 martensitic stainless steels to enhance their cavitation erosion resistance. These steels are commonly used in hydro turbines and boiler feed pumps. These treated steels have been evaluated for cavitation erosion resistance and it has been observed that the plasma ion-nitrocarburising process has significantly enhanced the cavitation erosion resistance as compared to untreated steel whereas HPDL-treated steels have shown marginal improvement. This is due to formation of high hardness nitrides during nitrocarburising and formation of moderate hardness martensitic phase due to rapid heating and cooling rates involved in HPDL treatment. The cavitation erosion and micro-hardness data of plasma ion-nitrocarburized as well as HPDL-treated steel samples and their comparison with hard deposits such as stellite and HVOF coating form the main part of the article.

  20. Corrosivity of paper mill effluent and corrosion performance of stainless steel.

    PubMed

    Ram, Chhotu; Sharma, Chhaya; Singh, A K

    2015-01-01

    Present study relates to the corrosivity of paper mill effluent and corrosion performance of stainless steel (SS) as a construction material for the effluent treatment plant (ETP). Accordingly, immersion test and electrochemical polarization tests were performed on SS 304 L, 316 L and duplex 2205 in paper mill effluent and synthetic effluent. This paper presents electrochemical polarization measurements, performed for the first time to the best of the authors' information, to see the influence of chlorophenols on the corrosivity of effluents. The corrosivity of the effluent was observed to increase with the decrease in pH and increase in Cl- content while the addition of SO4- tends to inhibit corrosion. Mill effluent was found to be more corrosive as compared to synthetic effluent and has been attributed to the presence of various chlorophenols. Corrosion performance of SS was observed to govern by the presence of Cr, Mo and N contents. PMID:25188842

  1. Distinguishing between chi and sigma phases in duplex stainless steels using potentiostatic etching

    SciTech Connect

    Jackson, E.M.L.E.M.; Visser, P.E. de . Physical Metallurgy Div.); Cornish, L.A. )

    1993-12-01

    A color interference film etching technique based on the principle of potentiostatic etching has been developed to distinguish, by optical metallography, between Cr-rich sigma and Mo-rich chi phases as well as with simultaneous identification of the ferrite and austenite phases in duplex stainless steels. The optical metallography results are confirmed by semiquantitative energy dispersive spectrometry analysis and back-scattered electron imaging. The technique is relatively simple and rapid, and makes use of low voltages and a hot etchant. Results have shown distinctively the sigma, chi, ferrite, and austenite phases, and enable observation of the microstructural development, morphology, and kinetics of formation of the phases in duplex alloys. The method, by giving excellent color contrast between sigma and chi, also facilitates quantitative image analysis of the sigma and chi volume fractions.

  2. Industrial Experience on the Caustic Cracking of Stainless Steels and Nickel Alloys - A Review

    SciTech Connect

    Rebak, R B

    2005-10-09

    Caustic environments are present in several industries, from nuclear power generation to the fabrication of alkalis and alumina. The most common material of construction is carbon steel but its application is limited to a maximum temperature of approximately 80 C. The use of Nickel (Ni) alloys is recommended at higher temperatures. Commercially pure Ni is the most resistant material for caustic applications both from the general corrosion and the stress corrosion cracking (SCC) perspectives. Nickel rich alloys also offer a good performance. The most important alloying elements are Ni and chromium (Cr). Molybdenum (Mo) is not a beneficial alloying element and it dissolves preferentially from the alloy in presence of caustic environments. Austenitic stainless steels such as type 304 and 316 seem less resistant to caustic conditions than even plain carbon steel. Experimental evidence shows that the most likely mechanism for SCC is anodic dissolution.

  3. Secondary electron yields of carbon-coated and polished stainless steel

    SciTech Connect

    Ruzic, D.; Moore, R.; Manos, D.; Cohen, S.

    1982-02-01

    To increase the power throughput to a plasma of an existing lower hybrid waveguide, secondary electron production on the walls and subsequent electron multiplication must be reduced. Since carbon has a low secondary electron coefficient (delta), measurements were performed for several uhv compatible carbon coatings (Aquadag, vacuum pyrolized Glyptal, and lamp black deposited by electrophoresis) as a function of primary beam voltage (35 eV to 10 keV), surface roughness (60 through 600 grit mechanical polishing and electropolishing), coating thickness, and angle of incidence (theta). Also measured were uncoated stainless steel, Mo, Cu, Ti, TiC, C as soot and ATJ graphite. The yields were obtained by varying the sample bias and measuring the collected current while the samples were in the electron beam of a scanning Auger microprobe. This technique allows delta measurements of Auger characterized surfaces with less than or equal to .3 mm spatial resolution.

  4. Qualification of welded super 13%Cr martensitic stainless steels for the Sgard field

    SciTech Connect

    Enerhaug, J.; Kvaale, P.E.; Bjordal, M.; Drugli, J.M.; Rogne, T.

    1999-11-01

    A test program was conducted to qualify welded super 13%Cr (S13%Cr) stainless steel for the Asgard Field, a mildly sour service. The test program involved girth welding, optimization of post weld heat treatment (PWHT) cycles, assessment of mechanical properties, examination of low cycle fatigue testing, and different corrosion testing and evaluation of S13%Cr steels from three different steel mills. The alloy with 0.015%C max, 11.9%Cr min, 2.4%Mo min and 6.O%Ni min, has been qualified for use as flowline material in the actual field. The results show acceptable weldability and corrosion properties. Post weld heat treatment (PWHT) of the welds improved the resistance against sulfide stress corrosion cracking.

  5. Properties of cryogenically worked metals. [stainless steels

    NASA Technical Reports Server (NTRS)

    Schwartzberg, F. R.; Kiefer, T. F.

    1975-01-01

    A program was conducted to determine whether the mechanical properties of cryogenically worked 17-7PH stainless steel are suitable for service from ambient to cryogenic temperatures. It was determined that the stress corrosion resistance of the cryo-worked material is quite adequate for structural service. The tensile properties and fracture toughness at room temperature were comparable to titanium alloy 6Al-4V. However, at cryogenic temperatures, the properties were not sufficient to recommend consideration for structural service.

  6. Pitting corrosion resistant austenite stainless steel

    DOEpatents

    van Rooyen, D.; Bandy, R.

    A pitting corrosion resistant austenite stainless steel comprises 17 to 28 wt. % chromium, 15 to 26 wt. % nickel, 5 to 8 wt. % molybdenum, and 0.3 to 0.5 wt. % nitrogen, the balance being iron, unavoidable impurities, minor additions made in the normal course of melting and casting alloys of this type, and may optionally include up to 10 wt. % of manganese, up to 5 wt. % of silicon, and up to 0.08 wt. % of carbon.

  7. Softened-Stainless-Steel O-Rings

    NASA Technical Reports Server (NTRS)

    Marquis, G. A.; Waters, William I.

    1993-01-01

    In fabrication of O-ring of new type, tube of 304 stainless steel bent around mandril into circle and welded closed into ring. Ring annealed in furnace to make it soft and highly ductile. In this condition, used as crushable, deformable O-ring seal. O-ring replacements used in variety of atmospheres and temperatures, relatively inexpensive, fabricated with minimum amount of work, amenable to one-of-a-kind production, reusable, and environmentally benign.

  8. Effect of ferrite on cast stainless steels

    SciTech Connect

    Nadezhdin, A.; Cooper, K. ); Timbers, G. . Kraft Pulp Division)

    1994-09-01

    Premature failure of stainless steel castings in bleach washing service is attributed to poor casting quality high porosity and to a high ferrite content, which makes the castings susceptible to corrosion by hot acid chloride solutions. A survey of the chemical compositions and ferrite contents of corrosion-resistant castings in bleach plants at three pulp mills found high [delta]-ferrite levels in the austenitic matrix due to the improper balance between austenite and ferrite stabilizers.

  9. Antimicrobial Cu-bearing stainless steel scaffolds.

    PubMed

    Wang, Qiang; Ren, Ling; Li, Xiaopeng; Zhang, Shuyuan; Sercombe, Timothy B; Yang, Ke

    2016-11-01

    Copper-bearing stainless steel scaffolds with two different structures (Body Centered Cubic and Gyroid labyrinth) at two solid fractions (25% and 40%) were fabricated from both 316L powder and a mixture of 316L and elemental Cu powder using selective laser melting, and relative 316L scaffolds were served as control group. After processing, the antimicrobial testing demonstrated that the 316L-Cu scaffolds presented excellent antimicrobial activity against Escherichia coli and Staphylococcus aureus, and the cell viability assay indicated that there was no cytotoxic effect of 316L-Cu scaffolds on rat marrow mesenchymal stem cells. As such, these have the potential to reduce implant-associated infections. The Cu was also found to homogeneously distribute within the microstructure by scanning electronic microcopy. The addition of Cu would not significantly affect its strength and stiffness compared to 316L scaffold, and the stiffness of all the scaffolds (3-20GPa) is similar to that of bone and much less than that of bulk stainless steel. Consequently, fabrication of such low stiffness porous structures, especially coupled with the addition of antimicrobial Cu, may provide a new direction for medical stainless steels. PMID:27524049

  10. SRS stainless steel beneficial reuse program

    SciTech Connect

    Boettinger, W.L.

    1997-02-01

    The US Department of Energy`s (DOE) Savannah River Site (SRS) has thousands of tons of stainless steel radioactive scrap metal (RSNI). Much of the metal is volumetrically contaminated. There is no {open_quotes}de minimis{close_quotes} free release level for volumetric material, and therefore no way to recycle the metal into the normal commercial market. If declared waste, the metal would qualify as low level radioactive waste (LLW) and ultimately be dispositioned through shallow land buried at a cost of millions of dollars. The metal however could be recycled in a {open_quotes}controlled release{close_quote} manner, in the form of containers to hold other types of radioactive waste. This form of recycle is generally referred to as {open_quotes}Beneficial Reuse{close_quotes}. Beneficial reuse reduces the amount of disposal space needed and reduces the need for virgin containers which would themselves become contaminated. Stainless steel is particularly suited for long term storage because of its resistance to corrosion. To assess the practicality of stainless steel RSM recycle the SRS Benficial Reuse Program began a demonstration in 1994, funded by the DOE Office of Science and Technology. This paper discusses the experiences gained in this program.

  11. Cast Stainless Steel Ferrite and Grain Structure

    SciTech Connect

    Ruud, Clayton O.; Ramuhalli, Pradeep; Meyer, Ryan M.; Mathews, Royce; Diaz, Aaron A.; Anderson, Michael T.

    2012-09-01

    In-service inspection requirements dictate that piping welds in the primary pressure boundary of light-water reactors be subject to a volumetric examination based on the rules contained within the American Society of Mechanical Engineers Boiler and Pressure Vessel Code, Section XI. The purpose of the inspection is the reliable detection and accurate sizing of service-induced degradation and/or material flaws introduced during fabrication. The volumetric inspection is usually carried out using ultrasonic testing (UT) methods. However, the varied metallurgical macrostructures and microstructures of cast austenitic stainless steel piping and fittings, including statically cast stainless steel and centrifugally cast stainless steel (CCSS), introduce significant variations in the propagation and attenuation of ultrasonic energy. These variations complicate interpretation of the UT responses and may compromise the reliability of UT inspection. A review of the literature indicated that a correlation may exist between the microstructure and the delta ferrite content of the casting alloy. This paper discusses the results of a recent study where the goal was to determine if a correlation existed between measured and/or calculated ferrite content and grain structure in CCSS pipe.

  12. Final report on CCT-K2.5: NRC/NMIJ/INRIM comparison of capsule-type standard platinum resistance thermometers from 13.8 K to 273.16 K

    NASA Astrophysics Data System (ADS)

    Hill, K. D.; Nakano, T.; Steur, P.

    2015-01-01

    A comparison of capsule-type standard platinum resistance thermometers (CSPRT) was carried out between NRC (Canada), NMIJ (Japan), and INRIM (Italy) over the temperature range 13.8 K to 273.16 K. The principal goal was to link the NMIJ realization of the International Temperature Scale of 1990 to the results of the Consultative Committee for Thermometry Key Comparison CCT-K2 over this temperature range. Additionally, in the intervening years since the CCT-K2 measurements were carried out, INRIM has improved the Italian national standards in the temperature range of the comparison, and was interested in the opportunity to update that assessment. The comparison has revealed the calibrations at NMIJ to be in agreement with the KCRV of CCT-K2 within the expanded uncertainty for all temperatures of the comparison. The linkage to the CCT-K2 data supports the inclusion of the NMIJ CMCs in Appendix C of the KCDB. The INRIM data are also consistent with the KCRV of CCT-K2 within the expanded uncertainty of the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

  13. Crystal structure of the co-crystalline adduct 1,3,6,8-tetra­aza­tri­cyclo­[4.4.1.13,8]dodecane (TATD)–4-bromo­phenol (1/2)

    PubMed Central

    Rivera, Augusto; Uribe, Juan Manuel; Rojas, Jicli José; Ríos-Motta, Jaime; Bolte, Michael

    2015-01-01

    The structure of the 1:2 co-crystalline adduct C8H16N4·2C6H5BrO, (I), from the solid-state reaction of 1,3,6,8-tetra­aza­tri­cyclo­[4.4.1.13,8]dodecane (TATD) and 4-bromo­phenol, has been determined. The asymmetric unit of the title co-crystalline adduct comprises a half mol­ecule of aminal cage polyamine plus a 4-bromo­phenol mol­ecule. A twofold rotation axis generates the other half of the adduct. The primary inter-species association in the title compound is through two inter­molecular O—H⋯N hydrogen bonds. In the crystal, the adducts are linked by weak non-conventional C—H⋯O and C—H⋯Br hydrogen bonds, giving a two-dimensional supra­molecular structure parallel to the bc plane. PMID:25995856

  14. Studies on Nb Microalloying of 13Cr Super Martensitic Stainless Steel

    NASA Astrophysics Data System (ADS)

    Ma, Xiaoping; Wang, Lijun; Subramanian, Sundaresa V.; Liu, Chunming

    2012-12-01

    The effect of Nb microalloying on microstructure, mechanical properties, and pitting corrosion properties of quenched and tempered 13 pct Cr-5 pct Ni-0.02 pct C martensitic stainless steels with different Mo and N contents was investigated. The microstructure, density, and dispersion of high-angle boundaries, nanoscale precipitates, and amount of retained austenite were characterized by using electron backscattered diffraction, transmission electron microscopy, and X-ray diffraction to correlate with properties. The results show that the combined effects of lowering nitrogen content in 13 pct Cr-5 pct Ni-1~2 pct Mo-0.02 pct C steels to 0.01 wt pct, and adding 0.1 pct Nb are to decrease the amount of Cr-rich precipitates, as Nb preferentially combines with residual carbon and nitrogen to form carbonitrides, suppressing the formation of Cr2N and Cr23C6. Austenite grain refinement can be achieved by Nb microalloying through proper heat treatment. If the nitrogen content is kept high, then Cr-rich precipitates would occur irrespective of microalloying addition. The NbN would also occur at high temperature, which will act as substrate for nucleation of coarse precipitates during subsequent tempering, impairing the toughness of the steel. It was shown that the addition of Nb to low interstitial super martensitic stainless steel retards the formation of reversed austenite and results in the formation of nanoscale precipitates (5 to 15 nm), which contribute to a significant increase in strength. More importantly, the pitting corrosion resistance was found to increase with Nb addition. This is attributed to suppression of Cr-rich precipitates, which can cause local depletion of Cr in the matrix and the initiation of pitting corrosion.

  15. Decontaminating and Melt Recycling Tritium Contaminated Stainless Steel

    SciTech Connect

    Clark, E.A.

    1995-04-03

    The Westinghouse Savannah River Company, Idaho National Engineering Laboratory, and several university and industrial partners are evaluating recycling radioactively contaminated stainless steel. The goal of this program is to recycle contaminated stainless steel scrap from US Department of Energy national defense facilities. There is a large quantity of stainless steel at the DOE Savannah River Site from retired heavy water moderated Nuclear material production reactors (for example heat exchangers and process water piping), that will be used in pilot studies of potential recycle processes. These parts are contaminated by fission products, activated species, and tritium generated by neutron irradiation of the primary reactor coolant, which is heavy (deuterated) water. This report reviews current understanding of tritium contamination of stainless steel and previous studies of decontaminating tritium exposed stainless steel. It also outlines stainless steel refining methods, and proposes recommendations based on this review.

  16. Amorphous stainless steel coatings prepared by reactive magnetron-sputtering from austenitic stainless steel targets

    NASA Astrophysics Data System (ADS)

    Cusenza, Salvatore; Schaaf, Peter

    2009-01-01

    Stainless steel films were reactively magnetron sputtered in argon/methane gas flow onto oxidized silicon wafers using austenitic stainless-steel targets. The deposited films of about 200 nm thickness were characterized by conversion electron Mössbauer spectroscopy, magneto-optical Kerr-effect, X-ray diffraction, scanning electron microscopy, Rutherford backscattering spectrometry, atomic force microscopy, corrosion resistance tests, and Raman spectroscopy. These complementary methods were used for a detailed examination of the carburization effects in the sputtered stainless-steel films. The formation of an amorphous and soft ferromagnetic phase in a wide range of the processing parameters was found. Further, the influence of the substrate temperature and of post vacuum-annealing were examined to achieve a comprehensive understanding of the carburization process and phase formation.

  17. Corrosion properties of stainless steel coatings made by different methods of thermal spraying

    SciTech Connect

    Siitonen, P.; Konos, T.; Kettunen, P.O.

    1994-12-31

    The corrosion protection ability of thermally sprayed stainless steel coatings in aggressive environments is considerably limited as compared to bulk materials of the same composition. The two main reasons for the decrease in corrosion resistance are the porosity in the coatings and the oxidation of elements, particularly chromium, during spraying process. The corrosion resistance and structure of stainless steel coatings, ANVAL 254 SMO, made by different methods of thermal spraying were evaluated in this work. The coatings were produced by atmospheric plasma spraying (APS), atmospheric plasma spraying using gas shielding around the plasma (APS/S), low pressure plasma spraying (LPPS), detonation gun spraying (DGS) and high velocity oxyfuel spraying (HVOF). Electrochemical methods were used for determining the corrosion protection ability of coatings in 3.5% NaCl-solution and in sulfur acid solution (pH 3 and 1). The structure and composition of coatings were studied by optical microscopy and scanning electron microscopy/energy dispersive analysator (SEM/EDS). The porosity of the coatings was determined by water impregnation method, optical microscopy and mercury porosimeter. The results showed that the best coating quality can be achieved by LPPS- and HVOF-coatings. Oxidation and porosity restrict the use of APS-coatings in corrosive environments. The oxidation can be avoided by using argon gas shield around the plasma flame during spraying. Due to porosity all studied coatings suffered crevice corrosion in chloride solution. Despite high Mo-alloying the best coatings reached only the corrosion resistance of AISI 316.

  18. Effect of ageing on precipitation and impact energy of 2101 economical duplex stainless steel

    SciTech Connect

    Zhang Wei; Jiang Laizhu Hu Jincheng; Song Hongmei

    2009-01-15

    The impact energy and microstructure of a thermally aged 2101 duplex stainless steel with composition of Fe-21.4Cr-1.2Ni-5.7Mn-0.23 N-0.31Mo were studied. The results showed that the room temperature impact energy of specimens decreased gradually with ageing temperature up to 700 deg. C and then increased with aging over 700 deg. C. The minimum value of impact energy was 37 J after 700 deg. C aging, which was only 34% of that for as-annealed specimens. For specimens aged at 700 deg. C, the room temperature impact energy decreased significantly after 3 min and was halved after 10 min. Fractographs showed that, with increasing aging time, the fracture morphology changed from fibrous fracture to transgranular and intragranular fracture. Scanning electron micrographs revealed that many precipitates were distributed along {alpha}/{gamma} and {alpha}/{alpha} interfaces. The precipitates were extracted and confirmed by X-ray diffraction to be Cr{sub 2}N. Therefore, it can be concluded that precipitation of Cr{sub 2}N is the main reason for the decrease of impact energy in aged 2101 duplex stainless steel.

  19. Secondary electron yields of carbon-coated and polished stainless steel

    SciTech Connect

    Ruzic, D.; Moore, R.; Manos, D.; Cohen, S.

    1982-04-01

    To increase the power throughput to a plasma of an existing lower hybrid waveguide, secondary electron production on the walls and subsequent electron multiplication must be reduced. Since carbon has a low secondary electron coefficient (delta), measurements were performed for several UHV compatible carbon coatings (Aquadag/sup X/, vacuum pyrolyzed Glyptal/sup X/, and lamp black deposited by electrophoresis) as a function of primary beam voltage (35 eV to 10 keV), surface roughness (60 through 600 grit mechanical polishing and electropolishing), coating thickness, and angle of incidence (theta). Also measured were uncoated stainless steel, Mo, Cu, Ti, TiC, and ATJ graphite. The yields were obtained by varying the sample bias and measuring the collected current while the samples were in the electron beam of a scanning Auger microprobe. This technique allows delta measurements of Auger characterized surfaces with < or =0.3 mm spatial resolution. Results show delta to have a typical energy dependence, with a peak occurring at 200 to 300 eV for normal incidence, and at higher energy for larger theta. In general, delta increases with theta more for smooth surfaces than for rough ones. Ninety percent of the secondary electrons have energies less than 25 eV. Some carbonized coating and surface treatment combinations give delta/sub max/ = 0.88 +- 0.01 for normal electron beam incidence: a reduction of almost 40% compared to untreated stainless steel.

  20. Partially degradable friction-welded pure iron-stainless steel 316L bone pin.

    PubMed

    Nasution, A K; Murni, N S; Sing, N B; Idris, M H; Hermawan, H

    2015-01-01

    This article describes the development of a partially degradable metal bone pin, proposed to minimize the occurrence of bone refracture by avoiding the creation of holes in the bone after pin removal procedure. The pin was made by friction welding and composed of two parts: the degradable part that remains in the bone and the nondegradable part that will be removed as usual. Rods of stainless steel 316L (nondegradable) and pure iron (degradable) were friction welded at the optimum parameters: forging pressure = 33.2 kPa, friction time = 25 s, burn-off length = 15 mm, and heat input = 4.58 J/s. The optimum tensile strength and elongation was registered at 666 MPa and 13%, respectively. A spiral defect formation was identified as the cause for the ductile fracture of the weld joint. A 40-µm wide intermetallic zone was identified along the fusion line having a distinct composition of Cr, Ni, and Mo. The corrosion rate of the pin gradually decreased from the undeformed zone of pure iron to the undeformed zone of stainless steel 316L. All metallurgical zones of the pin showed no toxic effect toward normal human osteoblast cells, confirming the ppb level of released Cr and Ni detected in the cell media were tolerable. PMID:24757071

  1. MoSi2-Base Composites

    NASA Technical Reports Server (NTRS)

    Hebsur, Mohan G.

    2003-01-01

    Addition of 30 to 50 vol% of Si3N4 particulate to MoSi2 eliminated its low temperature catastrophic failure, improved room temperature fracture toughness and the creep resistance. The hybrid composite SCS-6/MoSi2-Si3N4 did not show any matrix cracking and exhibited excellent mechanical and environmental properties. Hi-Nicalon continuous fiber reinforced MoSi2-Si3N4 also showed good strength and toughness. A new MoSi2-base composite containing in-situ whisker-type (Beta)Si3N4 grains in a MoSi2 matrix is also described.

  2. Water Droplet and Cavitation Erosion Behavior of Laser-Treated Stainless Steel and Titanium Alloy: Their Similarities

    NASA Astrophysics Data System (ADS)

    Mann, B. S.

    2013-12-01

    This article deals with water droplet and cavitation erosion behavior of diode laser-treated X10CrNiMoV1222 stainless steel and Ti6Al4V alloy. After laser surface treatment, the water droplet and cavitation erosion resistance (WDER and CER) of these materials improved significantly. The main reason for the improvement is the increased surface hardness and formation of fine-grained microstructures after laser surface treatment. It is observed that there is a similarity in both the phenomena. The WDER and CER can be correlated with a single mechanical property based on modified ultimate resilience (MUR) provided the laser-treated layers are free from microcracks and interface defects. The CER and WDER behavior of HPDL-treated X10CrNiMoV1222 stainless steel and Ti6Al4V alloy samples using different test equipment as per ASTM G32-2003 and ASTM G73-1978, their correlation with MUR, and their damage mechanism compared on the basis of XRD analyses, optical and scanning electron micrographs are discussed and reported in this article.

  3. Ion implantation modified stainless steel as a substrate for hydroxyapatite deposition. Part I. Surface modification and characterization.

    PubMed

    Pramatarova, L; Pecheva, E; Krastev, V; Riesz, F

    2007-03-01

    Material surfaces play critical role in biology and medicine since most biological reactions occur on surfaces and interfaces. There are many examples showing that the surface properties of the materials control and are directly involved in biological reactions and processes in-vitro like blood compatibility, protein absorption, cell development, etc. The rules that govern the diversity of biological surface phenomenon are fundamental physical laws. Stainless steel doped with Cr, Ni and Mo is widely used material in medicine and dentistry due to its excellent corrosion resistance and mechanical properties. The interest in this material has stimulated extensive studies on improving its bone-bonding properties. This paper describes the surface modification of Cr-Ni stainless steel (AISI 316) by a whole surface sequential implantation of Ca and P ions (the basic ions of hydroxyapatite). Three groups of stainless steel samples are prepared: (i) ion-implanted, (ii) ion-implanted and thermally treated at 600( composite function)C in air for 1 h and (iii) initials. The surface chemistry and topography before and after the surface modification are characterized by X-ray photoelectron spectroscopy, Auger electron spectroscopy, magic mirror method, atomic force microscopy and contact angle measurements. PMID:17334693

  4. Stainless Steel Leaches Nickel and Chromium into Foods During Cooking

    PubMed Central

    Kamerud, Kristin L.; Hobbie, Kevin A.; Anderson, Kim A.

    2014-01-01

    Toxicological studies show that oral doses of nickel and chromium can cause cutaneous adverse reactions such as dermatitis. Additional dietary sources, such as leaching from stainless steel cookware during food preparation, are not well characterized. This study examined stainless steel grades, cooking time, repetitive cooking cycles, and multiple types of tomato sauces for their effects on nickel and chromium leaching. Trials included three types of stainless steels and a stainless steel saucepan; cooking times of 2 to 20 hours, ten consecutive cooking cycles, and four commercial tomato sauces. After a simulated cooking process, samples were analyzed by ICP-MS for Ni and Cr. After six hours of cooking, Ni and Cr concentrations in tomato sauce increased up to 26- and 7-fold respectively, depending on the grade of stainless steel. Longer cooking durations resulted in additional increases in metal leaching, where Ni concentrations increased 34 fold and Cr increased approximately 35 fold from sauces cooked without stainless steel. Cooking with new stainless steel resulted in the largest increases. Metal leaching decreases with sequential cooking cycles and stabilized after the sixth cooking cycle, though significant metal contributions to foods were still observed. The tenth cooking cycle, resulted in an average of 88 μg of Ni and 86 μg of Cr leached per 126 g serving of tomato sauce. Stainless steel cookware can be an overlooked source of nickel and chromium, where the contribution is dependent on stainless steel grade, cooking time, and cookware usage. PMID:23984718

  5. Measurement of the direct CP -violating parameter ACP in the decay D<mo>+ stretchy='false'>→mo>K<mo>-mo>π<mo>+mo>π+>

    SciTech Connect

    Abazov, V. M.; Abbott, B.; Acharya, B. S.; Adams, M.; Adams, T.; Agnew, J. P.; Alexeev, G. D.; Alkhazov, G.; Alton, A.; Askew, A.; Atkins, S.; Augsten, K.; Avila, C.; Badaud, F.; Bagby, L.; Baldin, B.; Bandurin, D. V.; Banerjee, S.; Barberis, E.; Baringer, P.; Bartlett, J. F.; Bassler, U.; Bazterra, V.; Bean, A.; Begalli, M.; Bellantoni, L.; Beri, S. B.; Bernardi, G.; Bernhard, R.; Bertram, I.; Besançon, M.; Beuselinck, R.; Bhat, P. C.; Bhatia, S.; Bhatnagar, V.; Blazey, G.; Blessing, S.; Bloom, K.; Boehnlein, A.; Boline, D.; Boos, E. E.; Borissov, G.; Borysova, M.; Brandt, A.; Brandt, O.; Brock, R.; Bross, A.; Brown, D.; Bu, X. B.; Buehler, M.; Buescher, V.; Bunichev, V.; Burdin, S.; Buszello, C. P.; Camacho-Pérez, E.; Casey, B. C. K.; Castilla-Valdez, H.; Caughron, S.; Chakrabarti, S.; Chan, K. M.; Chandra, A.; Chapon, E.; Chen, G.; Cho, S. W.; Choi, S.; Choudhary, B.; Cihangir, S.; Claes, D.; Clutter, J.; Cooke, M.; Cooper, W. E.; Corcoran, M.; Couderc, F.; Cousinou, M. -C.; Cutts, D.; Das, A.; Davies, G.; de Jong, S. J.; De La Cruz-Burelo, E.; Déliot, F.; Demina, R.; Denisov, D.; Denisov, S. P.; Desai, S.; Deterre, C.; DeVaughan, K.; Diehl, H. T.; Diesburg, M.; Ding, P. F.; Dominguez, A.; Dubey, A.; Dudko, L. V.; Duperrin, A.; Dutt, S.; Eads, M.; Edmunds, D.; Ellison, J.; Elvira, V. D.; Enari, Y.; Evans, H.; Evdokimov, V. N.; Fauré, A.; Feng, L.; Ferbel, T.; Fiedler, F.; Filthaut, F.; Fisher, W.; Fisk, H. E.; Fortner, M.; Fox, H.; Fuess, S.; Garbincius, P. H.; Garcia-Bellido, A.; García-González, J. A.; Gavrilov, V.; Geng, W.; Gerber, C. E.; Gershtein, Y.; Ginther, G.; Gogota, O.; Golovanov, G.; Grannis, P. D.; Greder, S.; Greenlee, H.; Grenier, G.; Gris, Ph.; Grivaz, J. -F.; Grohsjean, A.; Grünendahl, S.; Grünewald, M. W.; Guillemin, T.; Gutierrez, G.; Gutierrez, P.; Haley, J.; Han, L.; Harder, K.; Harel, A.; Hauptman, J. M.; Hays, J.; Head, T.; Hebbeker, T.; Hedin, D.; Hegab, H.; Heinson, A. P.; Heintz, U.; Hensel, C.; Heredia-De La Cruz, I.; Herner, K.; Hesketh, G.; Hildreth, M. D.; Hirosky, R.; Hoang, T.; Hobbs, J. D.; Hoeneisen, B.; Hogan, J.; Hohlfeld, M.; Holzbauer, J. L.; Howley, I.; Hubacek, Z.; Hynek, V.; Iashvili, I.; Ilchenko, Y.; Illingworth, R.; Ito, A. S.; Jabeen, S.; Jaffré, M.; Jayasinghe, A.; Jeong, M. S.; Jesik, R.; Jiang, P.; Johns, K.; Johnson, E.; Johnson, M.; Jonckheere, A.; Jonsson, P.; Joshi, J.; Jung, A. W.; Juste, A.; Kajfasz, E.; Karmanov, D.; Katsanos, I.; Kaur, M.; Kehoe, R.; Kermiche, S.; Khalatyan, N.; Khanov, A.; Kharchilava, A.; Kharzheev, Y. N.; Kiselevich, I.; Kohli, J. M.; Kozelov, A. V.; Kraus, J.; Kumar, A.; Kupco, A.; Kurča, T.; Kuzmin, V. A.; Lammers, S.; Lebrun, P.; Lee, H. S.; Lee, S. W.; Lee, W. M.; Lei, X.; Lellouch, J.; Li, D.; Li, H.; Li, L.; Li, Q. Z.; Lim, J. K.; Lincoln, D.; Linnemann, J.; Lipaev, V. V.; Lipton, R.; Liu, H.; Liu, Y.; Lobodenko, A.; Lokajicek, M.; Lopes de Sa, R.; Luna-Garcia, R.; Lyon, A. L.; Maciel, A. K. A.; Madar, R.; Magaña-Villalba, R.; Malik, S.; Malyshev, V. L.; Mansour, J.; Martínez-Ortega, J.; McCarthy, R.; McGivern, C. L.; Meijer, M. M.; Melnitchouk, A.; Menezes, D.; Mercadante, P. G.; Merkin, M.; Meyer, A.; Meyer, J.; Miconi, F.; Mondal, N. K.; Mulhearn, M.; Nagy, E.; Narain, M.; Nayyar, R.; Neal, H. A.; Negret, J. P.; Neustroev, P.; Nguyen, H. T.; Nunnemann, T.; Orduna, J.; Osman, N.; Osta, J.; Pal, A.; Parashar, N.; Parihar, V.; Park, S. K.; Partridge, R.; Parua, N.; Patwa, A.; Penning, B.; Perfilov, M.; Peters, Y.; Petridis, K.; Petrillo, G.; Pétroff, P.; Pleier, M. -A.; Podstavkov, V. M.; Popov, A. V.; Prewitt, M.; Price, D.; Prokopenko, N.; Qian, J.; Quadt, A.; Quinn, B.; Ratoff, P. N.; Razumov, I.; Ripp-Baudot, I.; Rizatdinova, F.; Rominsky, M.; Ross, A.; Royon, C.; Rubinov, P.; Ruchti, R.; Sajot, G.; Sánchez-Hernández, A.; Sanders, M. P.; Santos, A. S.; Savage, G.; Savitskyi, M.; Sawyer, L.; Scanlon, T.; Schamberger, R. D.; Scheglov, Y.; Schellman, H.; Schwanenberger, C.; Schwienhorst, R.; Sekaric, J.; Severini, H.; Shabalina, E.; Shary, V.; Shaw, S.; Shchukin, A. A.; Simak, V.; Skubic, P.; Slattery, P.; Smirnov, D.; Snow, G. R.; Snow, J.; Snyder, S.; Söldner-Rembold, S.; Sonnenschein, L.; Soustruznik, K.; Stark, J.; Stoyanova, D. A.; Strauss, M.; Suter, L.; Svoisky, P.; Titov, M.; Tokmenin, V. V.; Tsai, Y. -T.; Tsybychev, D.; Tuchming, B.; Tully, C.; Uvarov, L.; Uvarov, S.; Uzunyan, S.; Van Kooten, R.; van Leeuwen, W. M.; Varelas, N.; Varnes, E. W.; Vasilyev, I. A.; Verkheev, A. Y.; Vertogradov, L. S.; Verzocchi, M.; Vesterinen, M.; Vilanova, D.; Vokac, P.; Wahl, H. D.; Wang, M. H. L. S.; Warchol, J.; Watts, G.; Wayne, M.; Weichert, J.; Welty-Rieger, L.; Williams, M. R. J.; Wilson, G. W.; Wobisch, M.; Wood, D. R.; Wyatt, T. R.; Xie, Y.; Yamada, R.; Yang, S.; Yasuda, T.; Yatsunenko, Y. A.; Ye, W.; Ye, Z.

    2014-12-01

    We measure the direct CP-violating parameter ACP for the decay of the charged charm meson, Dmo>+ stretchy="false">→mo>Kmo>-mo>πmo>+mo>πmo>+> (and charge conjugate), using the full 10.4 fbmo>->1 sample of ppmo accent="true" stretchy="false">¯mo> collisions at smo>=>1.96 TeV collected by the D0 detector at the Fermilab Tevatron collider. We extract the raw reconstructed charge asymmetry by fitting the invariant mass distributions for the sum and difference of charge-specific samples. This quantity is then corrected for detector-related asymmetries using data-driven methods and for possible physics asymmetries (from Bmo stretchy="false">→mo

  6. MoS2 spaser

    NASA Astrophysics Data System (ADS)

    Jayasekara, Charith; Premaratne, Malin; Gunapala, Sarath D.; Stockman, Mark I.

    2016-04-01

    We present a comprehensive analysis of a spaser made of a circular shaped highly doped molybdenum disulfide (MoS2) resonator. "Spaser" is an acronym for "surface plasmon amplification by stimulated emission of radiation"-a nanoscale source of surface plasmons generated by stimulated emission in a plasmonic resonator which receives energy nonradiatively. By considering localized surface plasmon modes, operation characteristics of the model are analysed, and tunability of the design is demonstrated. We find the optimum geometric and material parameters of the spaser that provides efficient outputs and carryout a comparative analysis with a similar circular spaser made of graphene. Owing to physical and chemical properties of MoS2 and the active medium, the proposed design delivers efficient outputs in terms of spaser mode energy, operating thresholds, Q-factor, and electric field amplitude. Lower operating thresholds and higher mode energies are notable advantages of the design. Owing to having many superior features to existing similar designs, this MoS2 spaser may be much suited for applications in nanoplasmonic devices.

  7. In-Situ hydrothermal synthesis of a MoS2 nanosheet electrode for electrochemical energy storage applications

    NASA Astrophysics Data System (ADS)

    Patel, Rajkumar; Inamdar, Akbar I.; Kim, Hyung Bae; Im, Hyunsik; Kim, Hyungsang

    2016-06-01

    A molybdenum disulfide (MoS2) nanosheet film was grown directly on a stainless-steel substrate by using an in-situ hydrothermal growth technique at 200 °C. The formation of an MoS2 hexagonal structure with a nanosheet-like morphology was confirmed by using X-ray diffraction (XRD) and field-emission scanning electron microscopy (FE-SEM) while a layered MoS2 nanosheet structure was observed under an energy-filtering transmission electron microscope (EF-TEM). The electrochemical supercapacitor properties of the MoS2 nanosheet electrode were measured in 1-M aqueous Na2SO4 electrolyte by using cyclic voltammetry (CV) and charge/discharge technique, and the electrode's specific capacitances were 91.29 F/g and 146.15 F/g, respectively. The concurrent double-layer capacitance and pseudo-capacitance behaviors of the electrode manifested themselves in the rectangular shape and redox peaks of the CV curve. The mesoporous MoS2 nanosheets were electrochemically stable for up to 1000 charge/discharge cycles.

  8. The effect of environment on the fatigue behavior of the amorphous metal, zirconium(41.2)titanium(13.8)copper(12.5)nickel(10)beryllium(22.5)

    NASA Astrophysics Data System (ADS)

    Schroeder, Valeska

    Electrochemical and mechanical experiments were conducted to analyze the environmentally influenced fatigue and fracture behavior of a bulk amorphous metal, Zr41.2Ti13.8Cu12.5Ni10Be 22.5 (at%), This study was motivated by a scientific interest in the mechanisms of fatigue crack propagation in an amorphous metal, and by a practical interest in the use of this amorphous metal in applications that take advantage of its unique properties, including high specific strength, large elastic strains and low damping. The objective of this work was to determine the rate and mechanism of fatigue-crack growth in this zirconium-based amorphous metal in an aggressive environment. To meet this objective, the synergism between mechanical loading and chemical environment was investigated experimentally. Specifically, fatigue crack propagation behavior was investigated at a range of stress intensities in representative service environments: ambient air, de-ionized water, and aerated aqueous sodium chloride solution. Based on these fatigue experiments, it was apparent that although water minimally increased growth rates compared to behavior in air, aerated 0.5 M sodium chloride solution dramatically increased growth rates by over two orders of magnitude near the fatigue threshold. In addition, values of crack velocity under sustained load (stress-corrosion) conditions in sodium chloride solution were comparable to crack-growth rates under cyclic loading in the same solution. Moreover, the effects of potential, concentration, stress intensity, anion type, and aeration on fatigue-crack growth, suggested that crack growth in sodium chloride solution was driven by a strain-assisted anodic reaction at the crack tip. Furthermore, the rate determining step appeared to differ near the fatigue threshold compared to that at higher stress intensities.

  9. A vacuum (10(exp -9) Torr) friction apparatus for determining friction and endurance life of MoSx films

    NASA Technical Reports Server (NTRS)

    Miyoshi, Kazuhisa; Honecy, Frank S.; Abel, Phillip B.; Pepper, Stephen V.; Spalvins, Talivaldis; Wheeler, Donald R.

    1992-01-01

    The first part of this paper describes an ultrahigh vacuum friction apparatus (tribometer). The tribometer can be used in a ball-on-disk configuration and is specifically designed to measure the friction and endurance life of solid lubricating films such as MoS(x) in vacuum at a pressure of 10 exp -7 Pa. The sliding mode is typically unidirectional at a constant rotating speed. The second part of this paper presents some representative friction and endurance life data for magnetron sputtered MoS(x) films (110 nm thick) deposited on sputter-cleaned 440 C stainless-steel disk substrates, which were slid against a 6-mm-diameter 440 C stainless-steel bearing ball. All experiments were conducted with loads of 0.49 to 3.6 N (average Hertzian contact pressure, 0.33 to 0.69 GPa), at a constant rotating speed of 120 rpm (sliding velocity ranging from 31 to 107 mm/s due to the range of wear track radii involved in the experiments), in a vacuum of 7 x 10 exp -7 Pa and at room temperature. The results indicate that there are similarities in friction behavior of MoS(x) films overs their life cycles regardless of load applied. The coefficient of friction (mu) decreases as load W increases according to mu = kW exp -1/3. The endurance life E of MoS(x) films decreases as the load W increases according to E = KW exp -1.4 for the load range. The load- (or contract-pressure-) dependent endurance life allows us to reduce the time for wear experiments and to accelerate endurance life testing of MoS(x) films. For the magnetron-sputtered MoS(x) films deposited on 440 C stainless-steel disks: the specific wear rate normalized to the load and the number of revolutions was 3 x 10 exp -8 mm exp 3/N-revolution; the specific wear rate normalized to the load and the total sliding distance was 8 x 10 exp -7 mm exp 3/N-m; and the nondimensional wear coefficient of was approximately 5 x 10 exp -6. The values are almost independent of load in the range 0.49 to 3.6 N (average Hertzian contact

  10. On the electronic structure of giant polyoxometalates: Mo132vs. W72Mo60.

    PubMed

    Bo, Carles; Miró, Pere

    2012-09-01

    The molecular and electronic structure of the spherical Keplerates [{(Mo(VI))Mo(VI)(5)O(21)}(12)(Mo(V)(2)O(4))(30)](12-) (Mo(132)) and [{(W(VI))W(VI)(5)O(21)}(12)(Mo(V)(2)O(4))(30)](12-) (W(72)Mo(60)) has been determined, for the first time, using first-principles density functional theory (DFT) based methods including solvent effects. Computed geometric parameters are in very good agreement with X-ray data, whereas the electronic structure reveals the archetypal nature of polyoxometalates. PMID:22717598

  11. Effect of alloying elements and residuals on corrosion resistance of type 444 stainless steel

    SciTech Connect

    Dowling, N.J.E.; Kim, Y.H.; Ahn, S.K.; Lee, Y.D.

    1999-02-01

    The principal criteria for the corrosion resistance of intermediate-grade ferritic stainless steels (SS) were examined in a neutral chloride (Cl{sup {minus}}) solution. The effect of increasing quantities of chromium and molybdenum was estimated for several heats in terms of the breakdown potential (E{sub b}). The effect of inclusions (particularly the oxide-sulfide type) in type 444 SS ([UNS S44400] 19% Cr-2% Mo-Nb or 19% Cr-2% Mo alloy), combined with the alloying element trend, permitted derivation of an expression that integrated both phenomena. The expression represents the mutually opposing effects of the chromium/molybdenum passive film reinforcement as represented by the pitting resistance equivalent number (PREN), as well as incorporating the deleterious contribution of the inclusion density ({Psi}/mm{sup 2}). Aluminum reduced the total inclusion content, which was associated with an increase in E{sub b}. Since no aluminum was detected in the passive film of high aluminum steels, it appeared likely that the prime effect of this element on corrosion resistance was via inclusion suppression. Corrosion studies of welded type 444 SS demonstrated that dual stabilization with low individual concentrations of titanium and niobium provided optimum corrosion resistance. This apparent synergism of niobium and titanium was independent of the surface of the welded materials, which were examined in the as-received, pickled, or polished states. The effect of the surface state in all cases was shown to exercise a critical effect on passive behavior.

  12. Residual Ferrite and Relationship Between Composition and Microstructure in High-Nitrogen Austenitic Stainless Steels

    NASA Astrophysics Data System (ADS)

    Wang, Qingchuan; Ren, Yibin; Yao, Chunfa; Yang, Ke; Misra, R. D. K.

    2015-12-01

    A series of high-nitrogen stainless steels (HNS) containing δ-ferrite, which often retained in HNS, were studied to establish the relationship between composition and microstructure. Both ferrite and nitrogen depletions were found in the center regions of cast ingots, and the depletion of nitrogen in that area was found to be the main reason for the existence of δ-ferrite. Because of the existence of heterogeneity, the variation of microstructure with nitrogen content was detected. Hence, the critical contents of nitrogen (CCN) for the fully austenitic HNS were obtained. Then the effects of elements such as N, Cr, Mn, and Mo on austenite stability were investigated via thermodynamic calculations. The CCN of HNS alloys were also obtained by calculations. Comparing the CCN obtained from experiment and calculation, it was found that the forged microstructure of the HNS was close to the thermodynamic equilibrium. To elucidate the above relationship, by regression analysis using calculated thermodynamic data, nitrogen equivalent and a new constitution diagram were proposed. The constitution diagram accurately distinguishes the austenitic single-phase region and the austenite + ferrite dual-phase region. The nitrogen equivalent and the new constitution diagram can be used for alloying design and microstructural prediction in HNS. According to the nitrogen equivalent, the ferrite stabilizing ability of Mo is weaker than Cr, and with Mn content increases, Mn behaves as a weak austenite stabilizer first and then as a ferrite stabilizer.

  13. Wear Characteristics of Ni-Based Hardfacing Alloy Deposited on Stainless Steel Substrate by Laser Cladding

    NASA Astrophysics Data System (ADS)

    Awasthi, Reena; Limaye, P. K.; Kumar, Santosh; Kushwaha, Ram P.; Viswanadham, C. S.; Srivastava, Dinesh; Soni, N. L.; Patel, R. J.; Dey, G. K.

    2015-03-01

    In this study, dry sliding wear characteristics of the Ni-based hardfacing alloy (Ni-Mo-Cr-Si) deposited on stainless steel SS316L substrate by laser cladding have been presented. Dry sliding wear behavior of the laser clad layer was evaluated against two different counter bodies, AISI 52100 chromium steel (~850 VHN) and tungsten carbide ball (~2200 VHN) to study both adhesive and abrasive wear characteristics, in comparison with the substrate SS316L using ball on plate reciprocating wear tester. The wear resistance was evaluated as a function of load and sliding speed for a constant sliding amplitude and sliding distance. The wear mechanisms were studied on the basis of wear surface morphology and microchemical analysis of the wear track using SEM-EDS. Laser clad layer of Ni-Mo-Cr-Si on SS316L exhibited much higher hardness (~700 VHN) than that of substrate SS316L (~200 VHN). The laser clad layer exhibited higher wear resistance as compared to SS316L substrate while sliding against both the counterparts. However, the improvement in the wear resistance of the clad layer as compared to the substrate was much higher while sliding against AISI 52100 chromium steel than that while sliding against WC, at the same contact stress intensity.

  14. Effects of vanadium on polarization of 18% Cr ferritic stainless steel

    SciTech Connect

    Davies, R.D. . Dept. of Metallurgy and Materials Engineering)

    1993-07-01

    Effects of alloying on the anodic polarization of a low interstitial, 18% chromium (Cr) ferritic stainless steel in sulfuric acid (H[sub 2]SO[sub 4]) were examined. Vanadium (V) from 1 to 4% was added alone and with up to 1.5% nickel (Ni), silicon (Si), copper (Cu), and molybdenum (MO). The carbon (C) and nitrogen (N) level varied from 84 to 168 ppm. The alloys were stabilized with titanium (Ti) or niobium (Nb). Increasing V had a variable effect on passivation in 1 N H[sub 2]SO[sub 4]. The critical current density for passivation lowered. The breakdown potential also lowered. Stabilization with Ti prevented lowering of the breakdown potential. Ni addition to Cr-V-Ti alloys broadened the passive region of the alloys and lowered the minimum current density for passivation. Mo and Cu were beneficial, but Si had little effect on passivation. The alloys did not appear to undergo intergranular corrosion in the modified Strauss test.

  15. Hydrogen induced plastic deformation of stainless steel

    SciTech Connect

    Gadgil, V.J.; Keim, E.G.; Geijselaers, H.J.M.

    1998-12-31

    Hydrogen can influence the behavior of materials significantly. The effects of hydrogen are specially pronounced in high fugacities of hydrogen which can occur at the surface of steels in contact with certain aqueous environments. In this investigation the effect of high fugacity hydrogen on the surface of stainless steel was investigated using electrochemical cathodic charging. Microhardness was measured on the cross section. Transmission electron microscopy was used to investigate the dislocation substructure just below the surface. Computer simulation using finite element method was carried out to estimate the extent and severity of the deformation. The significance of the results are discussed in relation to the loss of ductility due to hydrogen.

  16. Gas Atomization of Stainless Steel - Slow Motion

    SciTech Connect

    2011-01-01

    Stainless steel liquid atomized by supersonic argon gas into a spray of droplets at ~1800ºC. Atomization of metal requires high pressure gas and specialized chambers for cooling and collecting the powders without contamination. The critical step for morphological control is the impingement of the gas on the melt stream. The video is a black and white high speed video of a liquid metal stream being atomized by high pressure gas. This material was atomized at the Ames Laboratory's Materials Preparation Center http://www.mpc.ameslab.gov

  17. Adsorption and reaction of maleic anhydride on Mo(110), monolayer Pd(111)/Mo(110), and multilayer Pd(111)/Mo(110)

    SciTech Connect

    Xu, C.; Goodman, D.W.

    1996-04-03

    The adsorption and reaction of maleic anhydride and deuterated maleic anhydride on Mo(110), monolayer Pd/Mo(110), and multilayer Pd(111)/Mo(110) surfaces have been studied using temperature-programmed desorption (TPD) and high-resolution electron energy loss spectroscopy (HREELS). Maleic anhydride adsorbs irreversibly on the Mo(110) surface at 100 K. Heating to 1200 K yields adsorbed carbon (C{sub ads}) and gas-phase CO and H{sub 2}. In contrast, the adsorption of maleic anhydride on monolayer Pd(111)/Mo(110) and multilayer Pd(111)/Mo(110) surfaces is largely reversible with the chemisorbed maleic anhydride desorbing at 365 and 375 K, respectively. Approximately 15% of the chemisorbed maleic anhydride decomposes upon heating to 400K, forming CO, CO{sub 2} and C{sub 2}H{sub 2}; C{sub 2}H{sub 2} further dehydrogenates upon heating to C{sub ads} and gas-phase H{sub 2}. The HREELS measurements indicate that maleic anhydride is bonded to multilayer Pd(111)/Mo(110) through the olefin bond in a di-{sigma} configuration, while on monolayer Pd(111)/Mo(110), the maleic anhydride is bonded to the surface through the olefin via a {pi}-bond. On the Mo(110) surface, maleic anhydride is bonded to the surface through the ring oxygen with the molecular plane perpendicular to the surface. As a result of this modified adsorption geometry, the carbonyl stretching mode is red-shifted nearly 150 cm{sup -1} on the monolayer Pd(111)/Mo(110) surface, unshifted on the multilayer Pd(111)/Mo(110) surface, and blue-shifted by nearly 100 cm{sup -1} on the Mo(110) surface. 31 refs., 14 figs., 3 tabs.

  18. Comparison of spectral analysis with fast Fourier transform and maximum entropy method. Application to the role of molybdenum implantation on localized corrosion of Type 304 stainless steel

    SciTech Connect

    Beaunier, L.; Frydman, J.; Gabrielli, C.; Huet, F.; Keddam, M.

    1996-12-31

    A comparison of a spectral analysis using the fast Fourier transform (FFT) and the maximum entropy method (MEM) was carried out in the case in which both methods can be performed, that is, when several time acquisitions can be recorded. A summary of the principles of the MEM is given. Then the main properties of this method are investigated, that is, influence of the MEM order on the spectrum accuracy, validity of the low-frequency plateau usually given by this technique, overlapping of spectra measured for different frequency bandwidths, and influence of a slow evolution of the amplitude of the signal fluctuations. The susceptibility to pitting corrosion of type 304 stainless steel and type 304 modified by molybdenum (Mo) by means of ion implantation was studied. The power spectral densities (PSD) measured with the FFT and MEM techniques are in reasonable agreement, except for low electrochemical current noises (ECN) buried in the parasitic noise generated by the power supply. In that case, the FFT technique is more appropriate than the MEM, which gave qualitative results only. The type 304 stainless steel showed a large metastable pitting leading to only a few macroscopic pits, whereas the type 304 Mo-implanted specimen showed a very low metastable pitting leading to many hemispheric pits covered by the Mo-implanted layer, under which localized corrosion occurred.

  19. 77 FR 64545 - Drawn Stainless Steel Sinks From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-10-22

    ... respect to electronic filing have been amended. The amendments took effect on November 7, 2011. See 76 FR... COMMISSION Drawn Stainless Steel Sinks From China Scheduling of the final phase of countervailing duty and... retarded, by reason of subsidized and less-than-fair-value imports from China of drawn stainless...

  20. 78 FR 21417 - Drawn Stainless Steel Sinks From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-10

    ..., Washington, DC, and by publishing the notice in the Federal Register on October 22, 2012 (77 FR 64545). The... COMMISSION Drawn Stainless Steel Sinks From China Determinations On the basis of the record \\1\\ developed in... drawn stainless steel sinks from China, provided for in subheading 7324.10.00 of the Harmonized...

  1. 77 FR 23752 - Drawn Stainless Steel Sinks From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-20

    ... the notice in the Federal Register of March 7, 2012 (77 FR 13631). The conference was held in... COMMISSION Drawn Stainless Steel Sinks From China Determinations On the basis of the record \\1\\ developed in... (April 2012), entitled Drawn Stainless Steel Sinks from China: Investigation Nos. 701-TA-489 and...

  2. Nanostructured nickel-free austenitic stainless steel/hydroxyapatite composites.

    PubMed

    Tulinski, Maciej; Jurczyk, Mieczyslaw

    2012-11-01

    In this work Ni-free austenitic stainless steels with nanostructure and their nanocomposites with hydroxyapatite are presented and characterized by means of X-ray diffraction and optical profiling. The samples were synthesized by mechanical alloying, heat treatment and nitriding of elemental microcrystalline powders with addition of hydroxyapatite (HA). In our work we wanted to introduce into stainless steel hydroxyapatite ceramics that have been intensively studied for bone repair and replacement applications. Such applications were chosen because of their high biocompatibility and ability to bond to bone. Since nickel-free austenitic stainless steels seem to have better mechanical properties, corrosion resistance and biocompatibility compared to 316L stainless steels, it is possible that composite made of this steel and HA could improve properties, as well. Mechanical alloying and nitriding are very effective technologies to improve the corrosion resistance of stainless steel. Similar process in case of nanocomposites of stainless steel with hydroxyapatite helps achieve even better mechanical properties and corrosion resistance. Hence nanocrystalline nickel-free stainless steels and nickel-free stainless steel/hydroxyapatite nanocomposites could be promising bionanomaterials for use as a hard tissue replacement implants, e.g., orthopedic implants. In such application, the surface roughness and more specifically the surface topography influences the proliferation of cells (e.g., osteoblasts). PMID:23421285

  3. New Method For Joining Stainless Steel to Titanium

    NASA Technical Reports Server (NTRS)

    Emanuel, W. H.

    1982-01-01

    In new process, edge of stainless-steel sheet is perforated, and joined to titanium by resistance seam welding. Titanium flows into perforations, forming a strong interlocking joint. Process creates a quasi-metallurgical bond between the thin sheets of stainless steel and titanium.

  4. 6. DETAIL VIEW OF SPIN FORM FURNACE FOR STAINLESS STEEL ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    6. DETAIL VIEW OF SPIN FORM FURNACE FOR STAINLESS STEEL FABRICATION. STAINLESS STEEL WAS MACHINED IN SIDE A OF THE BUILDING, BEGINNING IN 1957. (4/24/78) - Rocky Flats Plant, Uranium Rolling & Forming Operations, Southeast section of plant, southeast quadrant of intersection of Central Avenue & Eighth Street, Golden, Jefferson County, CO

  5. VIEW OF PRECISION EQUIPMENT USED IN STAINLESS COMPONENT MANUFACTURING. THE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    VIEW OF PRECISION EQUIPMENT USED IN STAINLESS COMPONENT MANUFACTURING. THE FACILITY WAS DESCRIBED AS THE MOST MODERN NON-NUCLEAR MANUFACTURING BUILDING IN THE U.S. DEPARTMENT OF ENERGY COMPLEX, WITH MANY PRECISION INSTRUMENTS. (9/21/83) - Rocky Flats Plant, Stainless Steel & Non-Nuclear Components Manufacturing, Southeast corner of intersection of Cottonwood & Third Avenues, Golden, Jefferson County, CO

  6. Citric Acid Passivation of Stainless Steel

    NASA Technical Reports Server (NTRS)

    Yasensky, David; Reali, John; Larson, Chris; Carl, Chad

    2009-01-01

    Passivation is a process for cleaning and providing corrosion protection for stainless steel. Currently, on Kennedy Space Center (KSC), only parts passivated with nitric acid are acceptable for use. KSC disposes of approximately 125gal of concentrated nitric acid per year, and receives many parts from vendors who must also dispose of used nitric acid. Unfortunately, nitric acid presents health and environmental hazards. As a result, several recent industry studies have examined citric acid as an alternative. Implementing a citric acid-based passivation procedure would improve the health and environmental safety aspects of passivation process. However although there is a lack of published studies that conclusively prove citric acid is a technically sound passivation agent. In 2007, NASA's KSC Materials Advisory Working Group requested the evaluation of citric acid in place of nitric acid for passivation of parts at KSC. United Space Alliance Materials & Processes engineers have developed a three-phase test plan to evaluate citric acid as an alternative to nitric acid on three stainless steels commonly used at KSC: UNS S30400, S41000, and S17400. Phases 1 and 2 will produce an optimized citric acid treatment based on results from atmospheric exposure at NASA's Beach Corrosion Facility. Phase 3 will compare the optimized solution(s) with nitric acid treatments. If the results indicate that citric acid passivates as well or better than nitric acid, NASA intends to approve this method for parts used at the Kennedy Space Center.

  7. Weldment for austenitic stainless steel and method

    DOEpatents

    Bagnall, Christopher; McBride, Marvin A.

    1985-01-01

    For making defect-free welds for joining two austenitic stainless steel mers, using gas tungsten-arc welding, a thin foil-like iron member is placed between the two steel members to be joined, prior to making the weld, with the foil-like iron member having a higher melting point than the stainless steel members. When the weld is formed, there results a weld nugget comprising melted and then solidified portions of the joined members with small portions of the foil-like iron member projecting into the solidified weld nugget. The portions of the weld nugget proximate the small portions of the foil-like iron member which project into the weld nugget are relatively rich in iron. This causes these iron-rich nugget portions to display substantial delta ferrite during solidification of the weld nugget which eliminates weld defects which could otherwise occur. This is especially useful for joining austenitic steel members which, when just below the solidus temperature, include at most only a very minor proportion of delta ferrite.

  8. Embrittlement of austenitic stainless steel welds

    SciTech Connect

    David, S.A.; Vitek, J.M.

    1997-12-31

    The microstructure of type-308 austenitic stainless steel weld metal containing {gamma} and {delta} and ferrite is shown. Typical composition of the weld metal is Cr-20.2, Ni-9.4, Mn-1.7, Si-0.5, C-0.05, N-0.06 and balance Fe (in wt %). Exposure of austenitic stainless steel welds to elevated temperatures can lead to extensive changes in the microstructural features of the weld metal. On exposure to elevated temperatures over a long period of time, a continuous network of M{sub 23}C{sub 6} carbide forms at the austenite/ferrite interface. Upon aging at temperatures between 550--850 C, ferrite in the weld has been found to be unstable and transforms to sigma phase. These changes have been found to influence mechanical behavior of the weld metal, in particular the creep-rupture properties. For aging temperatures below 550 C the ferrite decomposes spinodally into {alpha} and {alpha}{prime} phases. In addition, precipitation of G-phase occurs within the decomposed ferrite. These transformations at temperatures below 550 C lead to embrittlement of the weld metal as revealed by the Charpy impact properties.

  9. Antibacterial polyelectrolyte micelles for coating stainless steel.

    PubMed

    Falentin-Daudré, Céline; Faure, Emilie; Svaldo-Lanero, Tiziana; Farina, Fabrice; Jérôme, Christine; Van De Weerdt, Cécile; Martial, Joseph; Duwez, Anne-Sophie; Detrembleur, Christophe

    2012-05-01

    In this study, we report on the original synthesis and characterization of novel antimicrobial coatings for stainless steel by alternating the deposition of aqueous solutions of positively charged polyelectrolyte micelles doped with silver-based nanoparticles with a polyanion. The micelles are formed by electrostatic interaction between two oppositely charged polymers: a polycation bearing 3,4-dihydroxyphenylalanine units (DOPA, a major component of natural adhesives) and a polyanion (poly(styrene sulfonate), PSS) without using any block copolymer. DOPA units are exploited for their well-known ability to anchor to stainless steel and to form and stabilize biocidal silver nanoparticles (Ag(0)). The chlorine counteranion of the polycation forms and stabilizes biocidal silver chloride nanoparticles (AgCl). We demonstrate that two layers of micelles (alternated by PSS) doped with silver particles are enough to impart to the surface strong antibacterial activity against gram-negative E. coli. Moreover, micelles that are reservoirs of biocidal Ag(+) can be easily reactivated after depletion. This novel water-based approach is convenient, simple, and attractive for industrial applications. PMID:22506542

  10. Electrochemical Testing of Ni-Cr-Mo-Gd Alloys

    SciTech Connect

    T. E. Lister; R. E. Mizia; H. Tian

    2005-10-01

    The waste package site recommendation design specified a boron-containing stainless steel, Neutronit 976/978, for fabrication of the internal baskets that will be used as a corrosion-resistant neutron-absorbing material. Recent corrosion test results gave higher-than-expected corrosion rates for this material. The material callout for these components has been changed to a Ni-Cr-Mo-Gd alloy (ASTM-B 932-04, UNS N06464) that is being developed at the Idaho National Laboratory. This report discusses the results of initial corrosion testing of this material in simulated in-package environments that could contact the fuel baskets after breach of the waste package outer barrier. The corrosion test matrix was executed using the potentiodynamic and potentiostatic electrochemical test techniques. The alloy performance shows low rates of general corrosion after initial removal of a gadolinium-rich second phase that intersects the surface. The high halide-containing test solutions exhibited greater tendencies toward initiation of crevice corrosion.

  11. Model studies of hydrodesulfurization by Mo

    SciTech Connect

    Friend, C.M.

    1992-01-01

    Effects of surface modifiers (Co, S) on activity and selectivity of Mo(110) for desulfurization processes were studied. S generally increases the selectivity for desulfurization while decreasing overall reactivity. Co promots C-H activation processes on Mo(110). The Mo(110)-(9x2)-Co surface affects the desulfurization of 2,5- dihydrothiophene and methanethiol. Vibrational spectroscopy is being used for determining molecular orientation; vibrational frequencies were calculated for four labeled 2-propoxide isomers on Mo(110) and found to agree with experiment.

  12. EXAFS Studies of Amorphous MoGe

    NASA Astrophysics Data System (ADS)

    Boyce, J. B.; Carter, W. L.; Geballe, T. H.; Claeson, T.

    1982-06-01

    Extended X-ray Absorption Fine Structure of amorphous and crystalline Mo-Ge samples sputter deposited on glass or kapton substrates was studied. Small local distortions were found in a substitutional b.c.c. Mo rich sample. A coordination in the range 5-7 and Ge-Mo distance of 2.65 A were estimated for an amorphous, intermediate composition Mo-Ge sample. The lack of superconductivity of some samples deposited on kapton was correlated to the presence of oxygen in the material.

  13. Mo99 Production Plant Layout

    SciTech Connect

    Woloshun, Keith Albert; Dale, Gregory E.; Naranjo, Angela Carol

    2015-06-25

    The NorthStar Medical Technologies 99Mo production facility configuration is envisioned to be 8 accelerator pairs irradiating 7 100Mo targets (one spare accelerator pair undergoing maintenance while the other 7 pairs are irradiating targets). The required shielding in every direction for the accelerators is initially estimated to be 10 feet of concrete. With the accelerator pairs on one (ground) level and spaced with the required shielding between adjacent pairs, the only practical path for target insertion and removal while minimizing floor space is vertical. The current scheme then requires a target vertical lift of nominally 10 feet through a shield stack. It is envisioned that the lift will be directly into a hot cell where an activated target can be removed from its holder and a new target attached and lowered. The hot cell is on a rail system so that a single hot cell can service all active target locations, as well as deliver the ready targets to the separations lab. On this rail system, coupled to the hot cell, will be a helium recovery and clean-up system. All helium coolant equipment is located on the upper level near to the target removal point.

  14. Endemic Mo Isotopic Anomalies in Iron and Carbonaceous Meteorites

    NASA Technical Reports Server (NTRS)

    Chen, J. H.; Papanastassiou, D. A.; Wasserburg, G. J.; Ngo, H. H.

    2004-01-01

    Mo in refractory interstellar grains shows large isotope anomalies. Recent Mo studies showed isotope effects in Allende and Murchison, and in iron meteorites, mesosiderites, and pallasites. Excesses of p- and r-process isotopes (or depletion of sprocess isotopes) of up to 3.5 epsilon units (epsilon u=parts in 10(exp 4)) were reported. We have reported on endemic isotope anomalies in Ru. Other workers have resolved no isotope anomalies for Mo or Ru and have claimed that the work by others is incorrect. Because Ru isotopes can interfere at Mo-96, Mo-98, Mo-100, we improved the chemical separations and eliminated interferences. For Mo work, we used the same solutions from which we separated and analyzed Ru. Three of the iron meteorites (Coahuila, Cape York, and Cape of Good Hope) were chosen for their large Mo isotopic effects. Mo was loaded on outgassed Re filaments, and then reduced; we used Ba(OH)2-NaOH as emitter, and measured Mo in static mode, as MoO3(-). We used Mo-98/Mo-96 for the mass fractionation correction (exponential law). No interferences from Ru or Zr isotopes were detected using the electron multiplier and no corrections were needed. For results on Mo standards we show 2 sigma(not 2 sigma mean) external precision better than: 0.7 epsilon u for Mo-94/Mo-96 and Mo-95/Mo-96; 1.0 epsilon u for Mo-92/Mo-96 and Mo-97/Mo-96; 1.4 epsilon u for Mo-100/Mo-96. Reproducibility for Mo standards is shown as contours (blue lines).

  15. Characterization of silane layers on modified stainless steel surfaces and related stainless steel-plastic hybrids

    NASA Astrophysics Data System (ADS)

    Honkanen, Mari; Hoikkanen, Maija; Vippola, Minnamari; Vuorinen, Jyrki; Lepistö, Toivo; Jussila, Petri; Ali-Löytty, Harri; Lampimäki, Markus; Valden, Mika

    2011-09-01

    The aim of this work was to characterize silane layers on the modified stainless steel surfaces and relate it to the adhesion in the injection-molded thermoplastic urethane-stainless steel hybrids. The silane layers were characterized with scanning electron microscope and transmission electron microscope, allowing the direct quantization of silane layer thickness and its variation. The surface topographies were characterized with atomic force microscope and chemical analyses were performed with X-ray photoelectron spectroscopy. The mechanical strength of the respective stainless steel-thermoplastic urethane hybrids was determined by peel test. Polishing and oxidation treatment of the steel surface improved the silane layer uniformity compared to the industrially pickled surface and increased the adhesion strength of the hybrids, resulting mainly cohesive failure in TPU. XPS analysis indicated that the improved silane bonding to the modified steel surface was due to clean Fe 2O 3-type surface oxide and stronger interaction with TPU was due to more amino species on the silane layer surface compared to the cleaned, industrially pickled surface. Silane layer thickness affected failure type of the hybrids, with a thick silane layer the hybrids failed mainly in the silane layer and with a thinner layer cohesively in plastic.

  16. Stainless Steel Round Robin Test: Centrifugally cast stainless steel screening phase

    SciTech Connect

    Bates, D.J.; Doctor, S.R.; Heasler, P.G.; Burck, E.

    1987-10-01

    This report presents the results of the Centrifugally Cast Stainless Steel Round Robin Test (CCSSRRT). The CCSSRRT is the first phase of an effort to investigate and improve the capability and reliability of NDE inspections of light water reactor piping systems. This phase was a screening test to identify the most promising procedures presently available for CCSS. The next phase will be an in-depth program to evaluate the capability and reliability of inservice inspections (ISI) for piping. In the CCSSRRT, 15 centrifugally cast stainless steel pipe sections containing welds and laboratory-grown thermal fatigue cracks in both columnar and equiaxed base material were used. These pipe specimens were inspected by a total of 18 teams from Europe and the United States using a variety of NDE techniques, mostly ultrasonic (UT). The inspections were carried out at the team's facilities and included inspections from both sides of the weld and inspections restricted to one side of the weld. The results of the CCSSRRT make it apparent that a more detailed study on the capability and reliability of procedures to inspect stainless steel materials is needed to better understand the specific material and flaw properties and how they affect the outcome of an inspection.

  17. Pr16Mo21O56

    PubMed Central

    Gougeon, Patrick; Gall, Philippe

    2011-01-01

    The structure of hexa­deca­praseodymium henicosa­molybden­um hexa­penta­contaoxide, Pr16Mo21O56, is isotypic with other rare earth representatives of formula type RE 16Mo21O56 (RE = La, Ce, Nd). It is characterized by Mo10O18 iO8 a units (where i = inner and a = apical O atoms) containing biocta­hedral Mo10 clusters and octa­hedral MoO6 units that share some of their O atoms to form the Mo–O framework. The two independent Mo10 cluster units are centred at Wyckoff positions 2b and 2c and have point-group symmetry . The Mo atom of the MoO6 unit is likewise situated at an inversion centre (2d). The eight crystallographically different Pr3+ cations occupy irregular voids in the framework with coordination numbers to the O atoms varying between 8 and 11. PMID:21754260

  18. Automatic welding of stainless steel tubing

    NASA Technical Reports Server (NTRS)

    Clautice, W. E.

    1978-01-01

    The use of automatic welding for making girth welds in stainless steel tubing was investigated as well as the reduction in fabrication costs resulting from the elimination of radiographic inspection. Test methodology, materials, and techniques are discussed, and data sheets for individual tests are included. Process variables studied include welding amperes, revolutions per minute, and shielding gas flow. Strip chart recordings, as a definitive method of insuring weld quality, are studied. Test results, determined by both radiographic and visual inspection, are presented and indicate that once optimum welding procedures for specific sizes of tubing are established, and the welding machine operations are certified, then the automatic tube welding process produces good quality welds repeatedly, with a high degree of reliability. Revised specifications for welding tubing using the automatic process and weld visual inspection requirements at the Kennedy Space Center are enumerated.

  19. Radiation resistant austenitic stainless steel alloys

    DOEpatents

    Maziasz, Philip J.; Braski, David N.; Rowcliffe, Arthur F.

    1989-01-01

    An austenitic stainless steel alloy, with improved resistance to radiation-induced swelling and helium embrittlement, and improved resistance to thermal creep at high temperatures, consisting essentially of, by weight percent: from 16 to 18% nickel; from 13 to 17% chromium; from 2 to 3% molybdenum; from 1.5 to 2.5% manganese; from 0.01 to 0.5% silicon; from 0.2 to 0.4% titanium; from 0.1 to 0.2% niobium; from 0.1 to 0.6% vanadium; from 0.06 to 0.12% carbon; from 0.01% to 0.03% nitrogen; from 0.03 to 0.08% phosphorus; from 0.005 to 0.01% boron; and the balance iron, and wherein the alloy may be thermomechanically treated to enhance physical and mechanical properties.

  20. THE CLEANING OF 303 STAINLESS STEEL

    SciTech Connect

    Shen, T H

    2004-04-20

    The sulfur found on the surfaces of stainless steel 303 (SS303) after nitric acid passivation originated from the MnS inclusions in the steel. The nitric acid attacked and dissolved these MnS inclusions, and redeposited micron-sized elemental sulfur particles back to the surface. To develop an alternative passivation procedure for SS303, citric and phosphoric acids have been evaluated. The experimental results show neither acid causes a significant amount of sulfur deposit. Thus, these two acids can be used as alternatives to nitric acid passivation for NIF applications. For SS303 previously passivated by nitric acid, NaOH soak can be used as a remedial cleaning process to effectively remove the sulfur deposits.

  1. Magnetic characterisation of duplex stainless steel

    NASA Astrophysics Data System (ADS)

    Mészáros, I.

    2006-02-01

    Heat treatment-induced microstructural processes were studied by different non-destructive magnetic and mechanical material testing methods in the present work. A commercial SAF 2507 type superduplex stainless steel was investigated. This alloy contains about 40% metastable ferrite which can decompose to a sigma phase and secondary austenite due to heat treatment. All the mechanical, corrosion resistance and magnetic properties are strongly influenced by this microstructural changes. This study had two aims: to understand better the kinetics of the ferrite decomposition process and to study the application possibilities of the applied magnetic measurements. This paper presents an application possibility of the nonlinear harmonics analysis measurement and demonstrates the possibility to find a quantitative correlation between measured harmonics and mechanical properties obtained from destructive tests.

  2. Wear evaluation of high interstitial stainless steel

    SciTech Connect

    Rawers, J.C.; Tylczak, J.H.

    2008-07-01

    A new series of high nitrogen-carbon manganese stainless steel alloys are studied for their wear resistance. High nitrogen and carbon concentrations were obtained by melting elemental iron-chromium-manganese (several with minor alloy additions of nickel, silicon, and molybdenum) in a nitrogen atmosphere and adding elemental graphite. The improvement in material properties (hardness and strength) with increasing nitrogen and carbon interstitial concentration was consistent with previously reported improvements in similar material properties alloyed with nitrogen only. Wear tests included: scratch, pin-on-disk, sand-rubber-wheel, impeller, and jet erosion. Additions of interstitial nitrogen and carbon as well as interstitial nitrogen and carbide precipitates were found to greatly improve material properties. In general, with increasing nitrogen and carbon concentrations, strength, hardness, and wear resistance increased.

  3. Radiation resistant austenitic stainless steel alloys

    DOEpatents

    Maziasz, P.J.; Braski, D.N.; Rowcliffe, A.F.

    1987-02-11

    An austenitic stainless steel alloy, with improved resistance to radiation-induced swelling and helium embrittlement, and improved resistance to thermal creep at high temperatures, consisting essentially of, by weight percent: from 16 to 18% nickel; from 13 to 17% chromium; from 2 to 3% molybdenum; from 1.5 to 2.5% manganese; from 0.01 to 0.5% silicon; from 0.2 to 0.4% titanium; from 0.1 to 0.2% niobium; from 0.1 to 0.6% vanadium; from 0.06 to 0.12% carbon; from 0.01 to 0.03% nitrogen; from 0.03 to 0.08% phosphorus; from 0.005 to 0.01% boron; and the balance iron, and wherein the alloy may be thermomechanically treated to enhance physical and mechanical properties. 4 figs.

  4. Automatic Welding of Stainless Steel Tubing

    NASA Technical Reports Server (NTRS)

    Clautice, W. E.

    1978-01-01

    To determine if the use of automatic welding would allow reduction of the radiographic inspection requirement, and thereby reduce fabrication costs, a series of welding tests were performed. In these tests an automatic welder was used on stainless steel tubing of 1/2, 3/4, and 1/2 inch diameter size. The optimum parameters were investigated to determine how much variation from optimum in machine settings could be tolerate and still result in a good quality weld. The process variables studied were the welding amperes, the revolutions per minute as a function of the circumferential weld travel speed, and the shielding gas flow. The investigation showed that the close control of process variables in conjunction with a thorough visual inspection of welds can be relied upon as an acceptable quality assurance procedure, thus permitting the radiographic inspection to be reduced by a large percentage when using the automatic process.

  5. MOCVD deposition of YSZ on stainless steels

    NASA Astrophysics Data System (ADS)

    Chevalier, S.; Kilo, M.; Borchardt, G.; Larpin, J. P.

    2003-01-01

    Yttria stabilized zirconia was deposited on stainless steel using the metal-organic chemical vapor deposition (MOCVD) technique, from β-diketonate precursors. The variation of the evaporation temperatures of yttrium and zirconium precursor allowed to control the level of Y within the film. Over the temperature range 125-150 °C, the Y content increased from 2.5 to 17.6 at.%. X-ray diffraction (XRD) analyses evidenced tetragonal phase of zirconia when the Y content was below 8 at.%, and cubic phase for higher concentration. Sputtered neutral mass spectrometry (SNMS) profiles confirmed that the control and stability of Y precursor temperature were of major importance to guarantee the homogeneity of the deposited films.

  6. Fatigue of stainless steel in hydrogen

    NASA Astrophysics Data System (ADS)

    Schuster, G.; Altstetter, C.

    1983-10-01

    The fatigue crack growth rates of two austenitic stainless steel alloys, AISI 301 and 302, were compared in air, argon, and hydrogen environments at atmospheric pressure and room temperature. Under the stresses at the crack tip the austenite in type 301 steel transformed martensitically to a’ to a greater extent than in type 302 steel. The steels were also tested in the cold worked condition under hydrogen or argon. Hydrogen was found to have a deleterious effect on both steels, but the effect was stronger in the unstable than in the stable alloy. Cold work decreased fatigue crack growth rates in argon and hydrogen, but the decrease was less marked in hydrogen than in argon. Metallographic, fractographic, and microhardness surveys in the vicinity of the fatigue crack were used to try to understand the reasons for the observed fatigue behavior.

  7. Hydrogen vibrations in austenitic stainless steel

    NASA Astrophysics Data System (ADS)

    Danilkin, S. A.; Delafosse, D.; Fuess, H.; Gavriljuk, V. G.; Ivanov, A.; Magnin, T.; Wipf, H.

    The vibrational modes of hydrogen in fcc Fe-25Cr-20Ni stainless steel with a hydrogen content of 0.33at.% were studied by neutron spectroscopy. Hydrogen doping was performed at 810K in a hydrogen-gas atmosphere of 190bar. Neutron spectra were taken at 2K and 77K with the spectrometer IN1-BeF (ILL, Grenoble). The spectra show the fundamental hydrogen vibration at 130 meV and the second harmonics at 260 meV. The frequencies are higher than in other fcc hydrides. In spite of the cubic symmetry of the octahedral hydrogen positions and the low hydrogen content, the inelastic hydrogen peak has a relatively large width and an asymmetric shape.

  8. Dendritic inhomogeneity of stainless maraging steels

    SciTech Connect

    Krasnikova, S.I.; Drobot, A.V.; Shmelev, A.Y.; Vukelich, S.B.

    1986-03-01

    The authors investigated dendritic inhomogeneity in industrial ingots 630 mm (steel I) in diameter and 500 mm (steel II) in diameter. The variation in the degree of dendritic inhomogeneity was investigated over the height of the ingots and across the sections on an MS-46 microprobe. It was established that the elements can be placed in the following order in accordance with the degree of reduction in the liquation factor: titanium, molybdenum, nickel, chromium, and cobalt. Titanium and molybdenum exhibit forward liquation in both steels, and chromium in steel II. The distribution of nickel and chromium in the steel I ingots and cobalt in the steel II ingots is unconventional. Dendritic inhomogeneity, which must be considered in assigning the heat treatment for finished articles, develops during the crystallization of stainless maraging steels.

  9. Solution chemistry of Mo(III) and Mo(IV): Thermodynamic foundation

    SciTech Connect

    Wang, Peiming; Wilson, L; Wesolowski, David J; Rosenqvist, Jorgen K; Anderko, Andrzej

    2010-01-01

    To investigate the behavior of molybdenum dissolution products in systems that approximate localized corrosion environments, solubility of Mo(III) in equilibrium with solid MoO2 has been determined at 80 C as a function of solution acidity, chloride concentration and partial pressure of hydrogen. The measurements indicate a strong increase in solubility with acidity and chloride concentration and a weak effect of hydrogen partial pressure. The obtained results have been combined with literature data for systems containing Mo(III), Mo(IV), and Mo(VI) in solutions to develop a comprehensive thermodynamic model of aqueous molybdenum chemistry. The model is based on a previously developed framework for simulating the properties of electrolyte systems ranging from infinite dilution to solid saturation or fused salt limit. To reproduce the measurements, the model assumes the presence of a chloride complex of Mo(III) (i.e., MoCl2+) and hydrolyzed species (MoOH2+, Mo(OH)2 +, and Mo(OH)3 0) in addition to the Mo3+ ion. The model generally reproduces the experimental data within experimental scattering and provides a tool for predicting the phase behavior and speciation in complex, concentrated aqueous solutions. Thus, it provides a foundation for simulating the behavior of molybdenum species in localized corrosion environments.

  10. Solution chemistry of Mo(III) and Mo(IV): Thermodynamic foundation for modeling localized corrosion.

    SciTech Connect

    Wang, P; Wilson, L; Wesolowski, David J

    2010-05-01

    To investigate the behavior of molybdenum dissolution products in systems that approximate localized corrosion environments, solubility of Mo(III) in equilibrium with solid MoO{sub 2} has been determined at 80 C as a function of solution acidity, chloride concentration and partial pressure of hydrogen. The measurements indicate a strong increase in solubility with acidity and chloride concentration and a weak effect of hydrogen partial pressure. The obtained results have been combined with literature data for systems containing Mo(III), Mo(IV), and Mo(VI) in solutions to develop a comprehensive thermodynamic model of aqueous molybdenum chemistry. The model is based on a previously developed framework for simulating the properties of electrolyte systems ranging from infinite dilution to solid saturation or fused salt limit. To reproduce the measurements, the model assumes the presence of a chloride complex of Mo(III) (i.e., MoCl{sup 2+}) and hydrolyzed species (MoOH{sup 2+}, Mo(OH){sup 2+}, and Mo(OH){sub 3}{sup 0}) in addition to the Mo{sup 3+} ion. The model generally reproduces the experimental data within experimental scattering and provides a tool for predicting the phase behavior and speciation in complex, concentrated aqueous solutions. Thus, it provides a foundation for simulating the behavior of molybdenum species in localized corrosion environments.

  11. Materials compatibility of hydride storage materials with austenitic stainless steels

    SciTech Connect

    Clark, E.A.

    1992-09-21

    This task evaluated the materials compatibility of LaNi[sub 5-x]Al[sub x] (x= 0.3, 0.75) hydrides and palladium coated kieselguhr with austenitic stainless steel in hydrogen and tritium process environments. Based on observations of retired prototype hydride storage beds and materials exposure testing samples designed for this study, no materials compatibility problem was indicated. Scanning electron microscopy observations of features on stainless steel surfaces after exposure to hydrides are also commonly found on as-received materials before hydriding. These features are caused by either normal heat treating and acid cleaning of stainless steel or reflect the final machining operation.

  12. Materials compatibility of hydride storage materials with austenitic stainless steels

    SciTech Connect

    Clark, E.A.

    1992-09-21

    This task evaluated the materials compatibility of LaNi{sub 5-x}Al{sub x} (x= 0.3, 0.75) hydrides and palladium coated kieselguhr with austenitic stainless steel in hydrogen and tritium process environments. Based on observations of retired prototype hydride storage beds and materials exposure testing samples designed for this study, no materials compatibility problem was indicated. Scanning electron microscopy observations of features on stainless steel surfaces after exposure to hydrides are also commonly found on as-received materials before hydriding. These features are caused by either normal heat treating and acid cleaning of stainless steel or reflect the final machining operation.

  13. Materials compatibility of hydride storage materials with austenitic stainless steels

    NASA Astrophysics Data System (ADS)

    Clark, E. A.

    1992-09-01

    This task evaluated the materials compatibility of LaNi(5-x)Al(x) (x= 0.3, 0.75) hydrides and palladium coated kieselguhr with austenitic stainless steel in hydrogen and tritium process environments. Based on observations of retired prototype hydride storage beds and materials exposure testing samples designed for this study, no materials compatibility problem was indicated. Scanning electron microscopy observations of features on stainless steel surfaces after exposure to hydrides are also commonly found on as-received materials before hydriding. These features are caused by either normal heat treating and acid cleaning of stainless steel or reflect the final machining operation.

  14. A preliminary ferritic-martensitic stainless steel constitution diagram

    SciTech Connect

    Balmforth, M.C.; Lippold, J.C.

    1998-01-01

    This paper describes preliminary research to develop a constitution diagram that will more accurately predict the microstructure of ferritic and martensitic stainless steel weld deposits. A button melting technique was used to produce a wide range of compositions using mixtures of conventional ferritic and martensitic stainless steels, including types 403, 409, 410, 430, 439 and 444. These samples were prepared metallographically, and the vol-% ferrite and martensite was determined quantitatively. In addition, the hardness and ferrite number (FN) were measured. Using this data, a preliminary constitution diagram is proposed that provides a more accurate method for predicting the microstructures of arc welds in ferritic and martensitic stainless steels.

  15. Radiation Chemistry of Simulated (99)Mo Product

    SciTech Connect

    Carson, S.D.; Garcia, M.J.; McDonald, M.J.; Simpson, R.L.; Tallant, D.R.

    1998-11-06

    PharrnaceuticaI houses that produce {sup 99}Tc/{sup 99}Tc generators have on occasion received {sup 99}Mo that contained a black precipitate. Addition of sodium hypochlorite to product bottles prior to shipment prevents precipitate formation, indicating the precipitate is a reduced form of Mo. The radiation effects of the dose from {sup 99}Mo on the product and product bottle have been determined by irradiating simulated {sup 99}Mo product solutions with the {sup 60}Co source at Sandia National Laboratories' Gamma Irradiation Facility (GE). The GIF experiment successfully generated a black precipitate in amounts sufficient for isolation and analysis by infrared and Rrunan spectroscopy. Changes in the pH of the basic {sup 99}Mo product solution during irradiation were monitored by titration. ResuIts of these analyses and the nature of the process that generates the precipitate, a mixture of molybdenum oxides that forms in plastic bottles, but not in glass containers, are discussed.

  16. Stainless steel-zirconium alloy waste forms

    SciTech Connect

    McDeavitt, S.M.; Abraham, D.P.; Keiser, D.D. Jr.; Park, J.Y.

    1996-07-01

    An electrometallurgical treatment process has been developed by Argonne National Laboratory to convert various types of spent nuclear fuels into stable storage forms and waste forms for repository disposal. The first application of this process will be to treat spent fuel alloys from the Experimental Breeder Reactor-II. Three distinct product streams emanate from the electrorefining process: (1) refined uranium; (2) fission products and actinides extracted from the electrolyte salt that are processed into a mineral waste form; and (3) metallic wastes left behind at the completion of the electrorefining step. The third product stream (i.e., the metal waste stream) is the subject of this paper. The metal waste stream contains components of the chopped spent fuel that are unaffected by the electrorefining process because of their electrochemically ``noble`` nature; this includes the cladding hulls, noble metal fission products (NMFP), and, in specific cases, zirconium from metal fuel alloys. The selected method for the consolidation and stabilization of the metal waste stream is melting and casting into a uniform, corrosion-resistant alloy. The waste form casting process will be carried out in a controlled-atmosphere furnace at high temperatures with a molten salt flux. Spent fuels with both stainless steel and Zircaloy cladding are being evaluated for treatment; thus, stainless steel-rich and Zircaloy-rich waste forms are being developed. Although the primary disposition option for the actinides is the mineral waste form, the concept of incorporating the TRU-bearing product into the metal waste form has enough potential to warrant investigation.

  17. Mo/Si and MoSi2/Si nanostructures for multilayer Laue lens

    NASA Astrophysics Data System (ADS)

    Takenaka, H.; Ichimaru, S.; Ohchi, T.; Koyama, T.; Tsuji, T.; Takano, H.; Kagoshima, Y.

    2009-09-01

    To develop a multilayer Laue lens (MLL), we fabricated depth-graded Mo/Si and MoSi2/Si multilayers with each boundary according to the Fresnel zone configuration. The multilayers were deposited by magnetron sputtering. From the result of SEM image analysis of the multilayer cross sections, MoSi2/Si multilayer had smaller layer-thickness errors than Mo/Si multilayer. In addition, from the result of the focusing test by using 20-keV X-rays, the measured beam size of MoSi2/Si MLL had a small blurring from the diffraction limited beam size. These results suggest that MoSi2/Si multilayer is better suited than Mo/Si multilayer for use as an MLL in hard x-ray nanofocusing.

  18. CO{sub 2} laser welding of duplex and super-duplex stainless steels (the effect of argon-nitrogen assist-gas mixtures)

    SciTech Connect

    Robinson, J.M.; Reed, R.C.; Camyab, A.

    1996-12-31

    Continuous wave CO{sub 2} laser welds have been fabricated on duplex and super duplex stainless steel substrates at a power of 3.5 kW. The work has examined the influence of Ar-N{sub 2} assist-gas mixtures on weld metal composition and microstructure. Welding in pure argon leads to reduction in the Cr, Ni, Mo and N content of the weld metal and a significant decrease in austenite volume fraction relative to the baseplate. Relative to welding in Ar, the use of a N{sub 2} bearing assist-gas restores the Cr, Ni and Mo levels to those found in the baseplate at the welding speeds employed. Moreover, the N{sub 2} bearing assist-gases result in an increase in the weld metal N content and austenite volume fraction relative to welding in pure Ar.

  19. Effect of Nitrogen Content on the Microstructure and Mechanical Properties of Ti-Mo-N Coating Films

    NASA Astrophysics Data System (ADS)

    Komiyama, Shoko; Sutou, Yuji; Koike, Junichi

    2011-11-01

    Effects of nitrogen content on the microstructure, hardness, and friction coefficient of Ti-Mo-N coating films were investigated. Ti-Mo-N films were deposited onto an AISI304 stainless steel substrate by reactive r.f. sputtering in the mixture of argon and nitrogen gases with various gas flow rates. The hardness and friction coefficients were measured by nanoindentation and ball-on-disk testing systems, respectively. The hardness of the Ti-Mo-N films increased with increasing a nitrogen gas flow rate ( {f_{{{{N}}2 }} } ) and showed a maximum hardness of about 30 GPa at a f_{{{{N}}2 }} = 0.3 {{ccm}} . On the one hand, the films deposited at f_{{{{N}}2 }} ge 1.0{{ccm}} showed a constant hardness value of approximately 25 GPa. On the other hand, the friction coefficient of the Ti-Mo-N film decreased with increasing N content and was 0.44 in the film deposited at f_{{{{N}}2 }} = 2.0{{ccm}}.

  20. Stainless steel anodes for alkaline water electrolysis and methods of making

    DOEpatents

    Soloveichik, Grigorii Lev

    2014-01-21

    The corrosion resistance of stainless steel anodes for use in alkaline water electrolysis was increased by immersion of the stainless steel anode into a caustic solution prior to electrolysis. Also disclosed herein are electrolyzers employing the so-treated stainless steel anodes. The pre-treatment process provides a stainless steel anode that has a higher corrosion resistance than an untreated stainless steel anode of the same composition.

  1. Long-Term Oxidation of Candidate Cast Iron and Advanced Austenitic Stainless Steel Exhaust System Alloys from 650-800 C in Air with Water Vapor

    DOE PAGESBeta

    Brady, Michael P; Muralidharan, Govindarajan; Leonard, Donovan N; Haynes, James A

    2014-01-01

    The oxidation behavior of SiMo cast iron, Ni-resist D5S cast iron, cast chromia-forming austenitic stainless steels of varying Cr/Ni content based on CF8C plus, HK, and HP, and a developmental cast alumina-forming austenitic (AFA) stainless steel of interest for diesel exhaust system components were studied for up to 5000 h at 650-800 C in air with 10% H2O. At 650 C, the Ni-resist D5S exhibited moderately better oxidation resistance than did the SiMo cast iron. However, the D5S suffered from oxide scale spallation issues at 700 C and higher, whereas the oxide scales formed on SiMo cast iron remained adherentmore » from 700-800 C despite oxide scales hundreds of microns thick. The oxidation of the SiMo cast iron exhibited unusual temperature dependence, with periods of slower oxidation kinetics at 750-800 C compared to 650-700 C due to continuous silica-rich scale formation at the higher temperatures. The oxidation of the cast chromia-forming austenitics trended with the level of Cr and Ni additions, with small mass losses consistent with Cr oxy-hydroxide volatilization processes for the higher 25Cr/25-35Ni HK and HP type alloys, and transition to rapid Fe-base oxide formation and scale spallation in the lower 19Cr/12Ni CF8C plus type alloy. In contrast, small positive mass changes consistent with protective alumina scale formation were observed for the cast AFA alloy under all conditions studied. Implications of these findings for diesel exhaust system components are discussed.« less

  2. Long-term oxidation of candidate cast iron and stainless steel exhaust system alloys from 650 to 800 °C in air with water vapor

    SciTech Connect

    Brady, Michael P.; Muralidharan, Govindarajan; Leonard, Donovan .; Haynes, James A.; Weldon, R. G.; England, R. D.

    2014-08-29

    Here, the oxidation behavior of SiMo cast iron, Ni-resist D5S cast iron, cast chromia-forming austenitic stainless steels of varying Cr/Ni content based on CF8C plus, HK, and HP, and a developmental cast alumina-forming austenitic (AFA) stainless steel of interest for diesel exhaust system components were studied for up to 5000 h at 650-800 °C in air with 10% H2O. At 650 °C, the Ni-resist D5S exhibited moderately better oxidation resistance than did the SiMo cast iron. However, the D5S suffered from oxide scale spallation issues at 700 °C and higher, whereas the oxide scales formed on SiMo cast iron remained adherent from 700-800 °C despite oxide scales hundreds of microns thick. The oxidation of the SiMo cast iron exhibited unusual temperature dependence, with periods of slower oxidation kinetics at 750-800 °C compared to 650-700 °C due to continuous silica-rich scale formation at the higher temperatures. The oxidation of the cast chromia-forming austenitics trended with the level of Cr and Ni additions, with small mass losses consistent with Cr oxy-hydroxide volatilization processes for the higher 25Cr/25-35Ni HK and HP type alloys, and transition to rapid Fe-base oxide formation and scale spallation in the lower 19Cr/12Ni CF8C plus type alloy. In contrast, small positive mass changes consistent with protective alumina scale formation were observed for the cast AFA alloy under all conditions studied. Implications of these findings for diesel exhaust system components are discussed.

  3. Long-term oxidation of candidate cast iron and stainless steel exhaust system alloys from 650 to 800 °C in air with water vapor

    DOE PAGESBeta

    Brady, Michael P.; Muralidharan, Govindarajan; Leonard, Donovan .; Haynes, James A.; Weldon, R. G.; England, R. D.

    2014-08-29

    Here, the oxidation behavior of SiMo cast iron, Ni-resist D5S cast iron, cast chromia-forming austenitic stainless steels of varying Cr/Ni content based on CF8C plus, HK, and HP, and a developmental cast alumina-forming austenitic (AFA) stainless steel of interest for diesel exhaust system components were studied for up to 5000 h at 650-800 °C in air with 10% H2O. At 650 °C, the Ni-resist D5S exhibited moderately better oxidation resistance than did the SiMo cast iron. However, the D5S suffered from oxide scale spallation issues at 700 °C and higher, whereas the oxide scales formed on SiMo cast iron remainedmore » adherent from 700-800 °C despite oxide scales hundreds of microns thick. The oxidation of the SiMo cast iron exhibited unusual temperature dependence, with periods of slower oxidation kinetics at 750-800 °C compared to 650-700 °C due to continuous silica-rich scale formation at the higher temperatures. The oxidation of the cast chromia-forming austenitics trended with the level of Cr and Ni additions, with small mass losses consistent with Cr oxy-hydroxide volatilization processes for the higher 25Cr/25-35Ni HK and HP type alloys, and transition to rapid Fe-base oxide formation and scale spallation in the lower 19Cr/12Ni CF8C plus type alloy. In contrast, small positive mass changes consistent with protective alumina scale formation were observed for the cast AFA alloy under all conditions studied. Implications of these findings for diesel exhaust system components are discussed.« less

  4. Continuing investigations for technology assessment of /sup 99/Mo production from LEU (low enriched Uranium) targets

    SciTech Connect

    Vandergrift, G.F.; Kwok, J.D.; Marshall, S.L.; Vissers, D.R.; Matos, J.E.

    1987-01-01

    Currently much of the world's supply of /sup 99m/Tc for medical purposes is produced from /sup 99/Mo derived from the fissioning of high enriched uranium (HEU). The need for /sup 99m/Tc is continuing to grow, especially in developing countries, where needs and national priorities call for internal production of /sup 99/Mo. This paper presents the results of our continuing studies on the effects of substituting low enriched Uranium (LEU) for HEU in targets for the production of fission product /sup 99/Mo. Improvements in the electrodeposition of thin films of uranium metal are reported. These improvements continue to increase the appeal for the substitution of LEU metal for HEU oxide films in cylindrical targets. The process is effective for targets fabricated from stainless steel or hastaloy. A cost estimate for setting up the necessary equipment to electrodeposit uranium metal on cylindrical targets is reported. Further investigations on the effect of LEU substitution on processing of these targets are also reported. Substitution of uranium silicides for the uranium-aluminum alloy or uranium aluminide dispersed fuel used in other current target designs will allow the substitution of LEU for HEU in these targets with equivalent /sup 99/Mo-yield per target and no change in target geometries. However, this substitution will require modifications in current processing steps due to (1) the insolubility of uranium silicides in alkaline solutions and (2) the presence of significant quantities of silicate in solution. Results to date suggest that both concerns can be handled and that substitution of LEU for HEU can be achieved.

  5. Alumina-Forming Austenitic Stainless Steels Strengthened by Laves Phase and MC Carbide Precipitates

    NASA Astrophysics Data System (ADS)

    Yamamoto, Y.; Brady, M. P.; Lu, Z. P.; Liu, C. T.; Takeyama, M.; Maziasz, P. J.; Pint, B. A.

    2007-11-01

    Creep strengthening of Al-modified austenitic stainless steels by MC carbides or Fe2Nb Laves phase was explored. Fe-20Cr-15Ni-(0-8)Al and Fe-15Cr-20Ni-5Al base alloys (at. pct) with small additions of Nb, Mo, W, Ti, V, C, and B were cast, thermally-processed, and aged. On exposure from 650 °C to 800 °C in air and in air with 10 pct water vapor, the alloys exhibited continuous protective Al2O3 scale formation at an Al level of only 5 at. pct (2.4 wt pct). Matrices of the Fe-20Cr-15Ni-5Al base alloys consisted of γ (fcc) + α (bcc) dual phase due to the strong α-Fe stabilizing effect of the Al addition and exhibited poor creep resistance. However, adjustment of composition to the Fe-15Cr-20Ni-5Al base resulted in alloys that were single-phase γ-Fe and still capable of alumina scale formation. Alloys that relied solely on Fe2Nb Laves phase precipitates for strengthening exhibited relatively low creep resistance, while alloys that also contained MC carbide precipitates exhibited creep resistance comparable to that of commercially available heat-resistant austenitic stainless steels. Phase equilibria studies indicated that NbC precipitates in combination with Fe2Nb were of limited benefit to creep resistance due to the solution limit of NbC within the γ-Fe matrix of the alloys studied. However, when combined with other MC-type strengtheners, such as V4C3 or TiC, higher levels of creep resistance were obtained.

  6. Chemical banding revealed by chemical etching in a cold-rolled metastable stainless steel

    SciTech Connect

    Celada, C.; Toda-Caraballo, I.; Kim, B.; San Martín, D.

    2013-10-15

    The current work describes the metallographic characterization of the initial microstructure of a cold rolled precipitation hardening semi-austenitic stainless steel (12Cr–9Ni–4Mo–2Cu–1Ti, in wt.%). The use of the Lichtenegger and Blöch (L–B) color etching solution has been shown to reveal not only the phases present in the microstructure, but also the existence of chemical banding along the rolling direction. The L–B reagent has been found to color the microstructure in bands depending on what alloying elements have segregated to each band. Two-dimensional electron probe microanalysis (EPMA) maps have shown that Ni, Cu and Ti segregate together in the bands, while Cr has an opposite behavior. Mo has a mixed segregation behavior although much weaker than the other elements and more prompt to segregate like Ni does. A direct comparison of light optical micrographs with the EPMA maps of the same area of the microstructure has enable to establish a direct relationship between the alloying element band concentration and the resulting etching color contrast obtained with the L–B reagent. Thermodynamic calculations predict that solidification in this steel takes place with ferrite as the primary phase. Equilibrium partitioning coefficient calculations seem to support the observed segregation patterns. - Highlights: • A cold rolled metastable stainless steel has been characterized thoroughly. • EPMA shows that Ni, Cu and Ti segregate together; Cr in an opposite way. • L–B color etching is sensitive to the segregation of these chemical elements. • This chemical banding has been reduced by applying a homogenization heat treatment. • Partitioning coefficient calculations agree with the observed segregation patterns.

  7. Ultrasonics permits brazing complex stainless steel assembly without flux

    NASA Technical Reports Server (NTRS)

    Baker, W. H.

    1967-01-01

    Ultrasonic vibration of an assembly of stainless steel instrumentation tubes ensures brazing without flux. Vibration with an ultrasonic transducer permits the brazing material to flow down each tube in contact with a seal plug installed in a pressure vessel wall.

  8. Stainless-steel elbows formed by spin forging

    NASA Technical Reports Server (NTRS)

    1964-01-01

    Large seamless austenitic stainless steel elbows are fabricated by spin forging /rotary shear forming/. A specially designed spin forging tool for mounting on a hydrospin machine has been built for this purpose.

  9. Surface modified stainless steels for PEM fuel cell bipolar plates

    DOEpatents

    Brady, Michael P [Oak Ridge, TN; Wang, Heli [Littleton, CO; Turner, John A [Littleton, CO

    2007-07-24

    A nitridation treated stainless steel article (such as a bipolar plate for a proton exchange membrane fuel cell) having lower interfacial contact electrical resistance and better corrosion resistance than an untreated stainless steel article is disclosed. The treated stainless steel article has a surface layer including nitrogen-modified chromium-base oxide and precipitates of chromium nitride formed during nitridation wherein oxygen is present in the surface layer at a greater concentration than nitrogen. The surface layer may further include precipitates of titanium nitride and/or aluminum oxide. The surface layer in the treated article is chemically heterogeneous surface rather than a uniform or semi-uniform surface layer exclusively rich in chromium, titanium or aluminum. The precipitates of titanium nitride and/or aluminum oxide are formed by the nitriding treatment wherein titanium and/or aluminum in the stainless steel are segregated to the surface layer in forms that exhibit a low contact resistance and good corrosion resistance.

  10. Stress corrosion cracking evaluation of precipitation-hardening stainless steel

    NASA Technical Reports Server (NTRS)

    Humphries, T. S.; Nelson, E. E.

    1970-01-01

    Accelerated test program results show which precipitation hardening stainless steels are resistant to stress corrosion cracking. In certain cases stress corrosion susceptibility was found to be associated with the process procedure.

  11. Fabrication of stainless steel clad tubing. [gas pressure bonding

    NASA Technical Reports Server (NTRS)

    Kovach, C. W.

    1978-01-01

    The feasibility of producing stainless steel clad carbon steel tubing by a gas pressure bonding process was evaluated. Such a tube product could provide substantial chromium savings over monolithic stainless tubing in the event of a serious chromium shortage. The process consists of the initial assembly of three component tubesets from conventionally produced tubing, the formation of a strong metallurgical bond between the three components by gas pressure bonding, and conventional cold draw and anneal processing to final size. The quality of the tubes produced was excellent from the standpoint of bond strength, mechanical, and forming properties. The only significant quality problem encountered was carburization of the stainless clad by the carbon steel core which can be overcome by further refinement through at least three different approaches. The estimated cost of clad tubing produced by this process is greater than that for monolithic stainless tubing, but not so high as to make the process impractical as a chromium conservation method.

  12. Utility chromium stainless steels in the transportation industry

    SciTech Connect

    Northart, J.F.

    1998-12-31

    The advantages of stainless steel in the Transportation Industry have been well documented over the last two decades. Benefits have been based on fractional maintenance costs, improved operational efficiency, and favorable life cycle cost. The bus and coach industry, as well as rail and trucking industry applications have all exhibited excellent histories utilizing stainless steels. The introduction of the new generation utility ferrilic stainless steels (11%--12% Chromium, or Cr 12) has led to a new and major benefit, which is driving the use of stainless steels in the transportation industry to new heights. Application of these corrosion resistant, utility steels in coal hopper cars, bus underframes, truck bodies and chassis, and even some European car chassis, has reshaped the thinking of those interested in excellent life cycle costing.

  13. Cavitation erosion of duplex and super duplex stainless steels

    SciTech Connect

    Kwok, C.T.; Man, H.C.; Cheng, F.T.

    1998-10-05

    Owing to their excellent corrosion resistance, stainless steels are widely used both in the marine, urban water, chemical and food industries. In addition to the corrosive environment, high fluid flow speeds are always encountered for components used in these industries. The cavitation characteristics of S30400 and S31600 austenitic stainless steels and duplex stainless steels were studied in detail by a number of authors. It was generally agreed that S30400 has higher cavitation erosion resistance than that of S31600 due to higher tendency of strain induced martensitic transformation under high impulse of stress. A considerable number of results on stress corrosion cracking characteristics of SDSS and duplex stainless steels have been published but data concerning their cavitation erosion property are extremely rare.

  14. Stress-Corrosion Cracking in Martensitic PH Stainless Steels

    NASA Technical Reports Server (NTRS)

    Humphries, T.; Nelson, E.

    1984-01-01

    Precipitation-hardening alloys evaluated in marine environment tests. Report describes marine-environment stress-corrosion cracking (SCC) tests of three martensitic precipitation hardening (PH) stainless-steel alloys.

  15. 3. INTERIOR VIEW OF SMOKEHOUSE UNIT; NOTE STAINLESS STEEL NOZZLES ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    3. INTERIOR VIEW OF SMOKEHOUSE UNIT; NOTE STAINLESS STEEL NOZZLES THAT INTRODUCED SMOKE INTO UNIT; FLOOR IS UNPAINTED STEEL - Rath Packing Company, Smokehouse-Hog Chilling Building, Sycamore Street between Elm & Eighteenth Streets, Waterloo, Black Hawk County, IA

  16. Nafion coated stainless steel for anti-biofilm application.

    PubMed

    Zhong, Li Juan; Pang, Li Qing; Che, Li Ming; Wu, Xue E; Chen, Xiao Dong

    2013-11-01

    Biofilms can adhere to most surfaces and have caused a wide range of problems in various industrial processes as well as daily life activities. In this work, the anti-biofilm ability of Nafion-coated stainless steel surface was investigated and our results showed that stainless steel discs coated with 1% Nafion can significantly reduce E. coli adhesion. Nafion has a large amount of negatively charged sulphonate groups, and the findings of this study suggest that the negative surface charge can greatly reduce bacterial adhesion through increasing the electrostatic repulsion between negatively charged bacterial cells and Nafion coated stainless steel surface. The roughness of coated and uncoated stainless steel discs made no significant differences while the hydrophobic of the discs increased after coated with Nafion. PMID:23831592

  17. Hafnium stainless steel absorber rod for control rod

    SciTech Connect

    Charnley, J.E.; Cearley, J.E.; Dixon, R.C.; Izzo, K.R.; Aiello, L.L.

    1989-08-01

    This patent describes an improvement in a control rod having a stainless steel body for enclosing a neutron absorbing poison, the control rod having movement along an axial direction for insertion into and out of a nuclear reactor for controlling a nuclear reaction. The improvement comprising: a piece of hafnium; a piece of stainless steel joined to the hafnium by a thin diffusion interface created by friction welding. The hafnium and the stainless steel oriented serially in the axial direction with the thin diffusion interface disposed normal to the axial direction of the control rod movement; means for confining the hafnium to movement along the axial direction with the control rod; and means for attaching the piece of stainless steel to the remaining portion of the control rod to load the weld therebetween under compression or tension during the control rod movement. Whereby the thin diffusion interface is loaded in tension or compression only upon dynamic movement of the control rod.

  18. Compressive Strength of Stainless-Steel Sandwiches at Elevated Temperatures

    NASA Technical Reports Server (NTRS)

    Mathauser, Eldon E.; Pride, Richard A.

    1959-01-01

    Experimental results are presented from crippling tests of stainless-steel sandwich specimens in the temperature range from 80 F to 1,200 F. The specimens included resistance-welded 17-7 PH stainless-steel sandwiches with single-corrugated cores, type 301 stainless-steel sandwiches with double-corrugated cores, and brazed 17-7 PH stainless-steel sandwiches with honeycomb cores. The experimental strengths are compared with predicted buckling and crippling strengths. The crippling strengths were predicted from the calculated maximum strength of the individual plate elements of the sandwiches and from a correlation procedure which gives the elevated-temperature crippling strength when the experimental room-temperature crippling strengths are known. Photographs of some of the tested specimens are included to show the modes of failure.

  19. Eddy sensors for small diameter stainless steel tubes.

    SciTech Connect

    Skinner, Jack L.; Morales, Alfredo Martin; Grant, J. Brian; Korellis, Henry James; LaFord, Marianne Elizabeth; Van Blarigan, Benjamin; Andersen, Lisa E.

    2011-08-01

    The goal of this project was to develop non-destructive, minimally disruptive eddy sensors to inspect small diameter stainless steel metal tubes. Modifications to Sandia's Emphasis/EIGER code allowed for the modeling of eddy current bobbin sensors near or around 1/8-inch outer diameter stainless steel tubing. Modeling results indicated that an eddy sensor based on a single axial coil could effectively detect changes in the inner diameter of a stainless steel tubing. Based on the modeling results, sensor coils capable of detecting small changes in the inner diameter of a stainless steel tube were designed, built and tested. The observed sensor response agreed with the results of the modeling and with eddy sensor theory. A separate limited distribution SAND report is being issued demonstrating the application of this sensor.

  20. Alumina-Forming Austenitics: A New Approach to Thermal and Degradation Resistant Stainless Steels for Industrial Use

    SciTech Connect

    David A Helmick; John H Magee; Michael P Brady

    2012-05-31

    A series of developmental AFA alloys was selected for study based on: 25 Ni wt.% (alloys A-F), 20 wt% Ni (alloys G-H), and 12 Ni wt.% (alloys I-L). An emphasis in this work was placed on the lower alloy content direction for AFA alloys to reduce alloy raw material cost, rather than more highly alloyed and costly AFA alloys for higher temperature performance. Alloys A-D explored the effects of Al (3-4 wt.%) and C (0.05-0.2 wt.%) in the Fe-25Ni-14Cr-2Mn-2Mo-1W-1Nb wt.% base range; alloys E and F explored the effects of removing costly Mo and W additions in a Fe-25Ni-14Cr-4Al-2.5Nb-2Mn-0.2C base, alloys G and H examined Nb (1-2.5wt.%) and removal of Mo, W in a Fe-20Ni-14Cr-3Al-2Mn-0.2 C wt.% base; and alloys I-L examined effects of C (0.1-0.2 wt.%) and Mn (5-10 wt.%) on a low cost Fe-14Cr-12Ni-3Cu-2.5Al wt.% base (no Mo, W additions). Creep testing resulted in elemental trends that included the beneficial effect of higher carbon and lower niobium in 20-25%Ni AFA alloys and, the beneficial of lower Mn in 12%Ni AFA alloys. Corrosion tests in steam and sulfidation-oxidation environments showed, in general, these alloys were capable of a ten-fold improvement in performance when compared to conventional austenitic stainless steels. Also, corrosion test results in metal-dusting environments were promising and, warrant further investigation.

  1. MoRFchibi SYSTEM: software tools for the identification of MoRFs in protein sequences.

    PubMed

    Malhis, Nawar; Jacobson, Matthew; Gsponer, Jörg

    2016-07-01

    Molecular recognition features, MoRFs, are short segments within longer disordered protein regions that bind to globular protein domains in a process known as disorder-to-order transition. MoRFs have been found to play a significant role in signaling and regulatory processes in cells. High-confidence computational identification of MoRFs remains an important challenge. In this work, we introduce MoRFchibi SYSTEM that contains three MoRF predictors: MoRFCHiBi, a basic predictor best suited as a component in other applications, MoRFCHiBi_ Light, ideal for high-throughput predictions and MoRFCHiBi_ Web, slower than the other two but best for high accuracy predictions. Results show that MoRFchibi SYSTEM provides more than double the precision of other predictors. MoRFchibi SYSTEM is available in three different forms: as HTML web server, RESTful web server and downloadable software at: http://www.chibi.ubc.ca/faculty/joerg-gsponer/gsponer-lab/software/morf_chibi/. PMID:27174932

  2. Measurement of intergranular attack in stainless steel using ultrasonic energy

    DOEpatents

    Mott, Gerry; Attaar, Mustan; Rishel, Rick D.

    1989-08-08

    Ultrasonic test methods are used to measure the depth of intergranular attack (IGA) in a stainless steel specimen. The ultrasonic test methods include a pitch-catch surface wave technique and a through-wall pulse-echo technique. When used in combination, these techniques can establish the extent of IGA on both the front and back surfaces of a stainless steel specimen from measurements made on only one surface.

  3. Probing the duplex stainless steel phases via magnetic force microscopy

    NASA Astrophysics Data System (ADS)

    Gheno, S. M.; Santos, F. S.; Kuri, S. E.

    2008-03-01

    Duplex stainless steels are austenitic-ferritic alloys used in many applications, thanks to their excellent mechanical properties and high corrosion resistance. In this work, chemical analyses, x-ray diffraction, and magnetic force microscopy (MFM) were employed to characterize the solution annealed and aged duplex stainless steel. The samples exhibited no changes in lattice parameters and the MFM technique proved successful in clearly imaging the magnetic domain structure of the ferrite phase.

  4. Procedure for flaw detection in cast stainless steel

    DOEpatents

    Kupperman, David S.

    1988-01-01

    A method of ultrasonic flaw detection in cast stainless steel components incorporating the steps of determining the nature of the microstructure of the cast stainless steel at the site of the flaw detection measurements by ultrasonic elements independent of the component thickness at the site; choosing from a plurality of flaw detection techniques, one such technique appropriate to the nature of the microstructure as determined and detecting flaws by use of the chosen technique.

  5. Laser surface melting and alloying of type 304L stainless steel: Improvement of corrosion and wear properties. Final report

    SciTech Connect

    Inal, O.T.

    1994-08-01

    Laser surface melting (LSM) of type 304L stainless steel and laser surface alloying (LSA) of this stainless steel with Mo and Ta have been studied to determine if corrosion and wear resistance properties can be improved. It was observed that these properties were affected by the presence of {delta}-ferrite, produced by the high cooling rate associated with LSM, as well as by compositional modifications in Mo-and Ta-alloyed layers. The {delta}-ferrite content was calculated from X-ray diffraction data to be 4.3 vol%, 77 vol% and 76 vol% for LSM, Mo-alloyed and Ta-alloyed LSA layers, respectively. Laser processing caused a lowered Mn content, by about 15%, and introduced extensive Mn-Si precipitation in the microstructure. In the LSM layer, the hardness increase was observed to be 10% due to refinement in subgrain structure. There was no martensitic transformation in the melted layer. {delta}-ferrite content was found to increase from 4.3 vol% at the surface to 9.9 vol% at the fusion line due to different cooling rates present in the melted layer. Passivation and pitting properties were seen to be enhanced with increase in {delta}-ferrite content in LSM samples. This is attributed to a primary solidification mode of {delta}-ferrite which dissolves more impurity elements, such as S, than austenite, as well as the removal and/or redistribution of inclusions in the melted layer. The stress corrosion cracking resistance of the melted layer was observed to be lowered; this is possibly because of the detriment to mechanical properties introduced by laser melting in the form of lowered ductility. The Mo-alloyed layer exhibited 50% increase in hardness, compared with the substrate, due to higher {delta}-ferrite content. It spontaneously passivated in 1N H{sub 2}SO{sub 4} solution, and there was no pit formation in 3.5 wt% NaCl and 10% FeCl{sub 3}{center_dot}6H{sub 2}O solutions.

  6. Solidification behavior of austenitic stainless steel filler metals

    SciTech Connect

    David, S.A.; Goodwin, G.M.; Braski, D.N.

    1980-02-01

    Thermal analysis and interrupted solidification experiments on selected austenitic stainless steel filler metals provided an understanding of the solidification behavior of austenitic stainless steel welds. The sequences of phase separations found were for type 308 stainless steel filler metal, L + L + delta + L + delta + ..gamma.. ..-->.. ..gamma.. + delta, and for type 310 stainless steel filler metal, L ..-->.. L + ..gamma.. ..-->.. ..gamma... In type 308 stainless steel filler metal, ferrite at room temperature was identified as either the untransformed primary delta-ferrite formed during the initial stages of solidification or the residual ferrite after Widmanstaetten austenite precipitation. Microprobe and scanning transmission electron microscope microanalyses revealed that solute extensively redistributes during the transformation of primary delta-ferrite to austenite, leading to enrichment and stabilization of ferrite by chromium. The type 310 stainless steel filler metal investigated solidifies by the primary crystallization of austenite, with the transformation going to completion at the solidus temperature. In our samples residual ferrite resulting from solute segregation was absent at the intercellular or interdendritic regions.

  7. Nickel release from nickel-plated metals and stainless steels.

    PubMed

    Haudrechy, P; Foussereau, J; Mantout, B; Baroux, B

    1994-10-01

    Nickel release from nickel-plated metals often induces allergic contact dermatitis, but, for nickel-containing stainless steels, the effect is not well-known. In this paper, AISI 304, 316L, 303 and 430 type stainless steels, nickel and nickel-plated materials were investigated. 4 tests were performed: patch tests, leaching experiments, dimethylglyoxime (DMG) spot tests and electrochemical tests. Patch tests showed that 96% of the patients were intolerant to Ni-plated samples, and 14% to a high-sulfur stainless steel (303), while nickel-containing stainless steels with a low sulfur content elicited no reactions. Leaching experiments confirmed the patch tests: in acidic artificial sweat, Ni-plated samples released about 100 micrograms/cm2/week of nickel, while low-sulfur stainless steels released less than 0.03 microgram/cm2/week of nickel, and AISI 303 about 1.5 micrograms/cm2/week. Attention is drawn to the irrelevance of the DMG spot test, which reveals Ni present in the metal bulk but not its dissolution rate. Electrochemical experiments showed that 304 and 316 grades remain passive in the environments tested, while Ni-plated steels and AISI 303 can suffer significant cation dissolution. Thus, Ni-containing 304 and 316 steels should not induce contact dermatitis, while 303 should be avoided. A reliable nitric acid spot test is proposed to distinguish this grade from other stainless steels. PMID:7842681

  8. X-ray attenuation properties of stainless steel (u)

    SciTech Connect

    Wang, Lily L; Berry, Phillip C

    2009-01-01

    Stainless steel vessels are used to enclose solid materials for studying x-ray radiolysis that involves gas release from the materials. Commercially available stainless steel components are easily adapted to form a static or a dynamic condition to monitor the gas evolved from the solid materials during and after the x-ray irradiation. Experimental data published on the x-ray attenuation properties of stainless steel, however, are very scarce, especially over a wide range of x-ray energies. The objective of this work was to obtain experimental data that will be used to determine how a poly-energetic x-ray beam is attenuated by the stainless steel container wall. The data will also be used in conjunction with MCNP (Monte Carlos Nuclear Particle) modeling to develop an accurate method for determining energy absorbed in known solid samples contained in stainless steel vessels. In this study, experiments to measure the attenuation properties of stainless steel were performed for a range of bremsstrahlung x-ray beams with a maximum energy ranging from 150 keV to 10 MeV. Bremsstrahlung x-ray beams of these energies are commonly used in radiography of engineering and weapon components. The weapon surveillance community has a great interest in understanding how the x-rays in radiography affect short-term and long-term properties of weapon materials.

  9. Effect of composition on the transformation of {delta}-ferrite to {sigma} in type 316 stainless steel weld metals

    SciTech Connect

    Gill, T.P.S.; Shankar, V.; Pujar, M.G.; Rodriguez, P.

    1995-05-15

    A study of the effect of Cr on {delta}-ferrite transformation kinetics has yielded a relationship between the kinetics parameter n{sub 2} and weld metal chromium content. The amount of {sigma}{sub 0.9} formed from {delta}-ferrite has been correlated with weld metal composition. A nomogram is proposed, to predict the amount of {sigma}{sub 0.9} formed after 90% ferrite transformation in a given weld metal, as a function of C, Cr and Mo contents. The nomogram can be employed to optimize the composition for reducing high temperature embrittlement resulting from {sigma} precipitation in type 316 stainless steel weld metals. The nomogram has been developed from data obtained at 650 C but has been shown to be valid in the temperature range 600--700 C.

  10. Methodology for optimizing the electropolishing of stainless steel AISI 316L combining criteria of surface finish and dimensional precision

    NASA Astrophysics Data System (ADS)

    Núñez, P. J.; García-Plaza, E.; Martín, A. R.; Trujillo, R.; De la Cruz, C.

    2009-11-01

    This work examines a methodology for optimizing electrochemical polishing conditions bearing in mind the criteria that enhance minimum surface roughness and dimensional precision (minimum loss of thickness). The study consisted in electrochemically polishing stainless steel AISI 316L (ISO 4954 X2CrNiMo17133E) under a combination of different temperatures (T) baths and current densities (J), and application times (t). The surface finish (ΔRa) and dimensional variations (Δh) of the electrochemically polished workpieces were assessed, and the experimental data of the variables was correlated as can be seen by the response surfaces. This methodology enables optimum working areas to be specified using the sole criteria of surface finish, or by using a combination of both criteria (minimum roughness and maximum precision). The methodology has proven to be an optimum method for selecting electrochemical polishing conditions using the combined criteria of surface finish and dimensional precision in accordance with design requirements.

  11. Thermophysical Properties of U-10MO Alloy

    SciTech Connect

    A. M. Phillips; G. S. Mickum; D. E. Burkes

    2010-11-01

    This report provides an overview of thermophysical properties of unirradiated uranium alloyed with ten weight percent molybdenum (U 10Mo), with particular focus on those material properties needed for modeling of new fuels for HPRRs (High Performance Research Reactors). The report contains both historical data available in the literature on U-10Mo, as well as more recent results conducted by the Global Threat Reduction Initiative fuel development program. The main use of the report is intended as a standard U-10Mo alloy properties reference for reactor models and simulations.

  12. Wafer-scale MoS2 thin layers prepared by MoO3 sulfurization.

    PubMed

    Lin, Yu-Chuan; Zhang, Wenjing; Huang, Jing-Kai; Liu, Keng-Ku; Lee, Yi-Hsien; Liang, Chi-Te; Chu, Chih-Wei; Li, Lain-Jong

    2012-10-21

    Atomically thin molybdenum disulfide (MoS(2)) layers have attracted great interest due to their direct-gap property and potential applications in optoelectronics and energy harvesting. Meanwhile, they are extremely bendable, promising for applications in flexible electronics. However, the synthetic approach to obtain large-area MoS(2) atomic thin layers is still lacking. Here we report that wafer-scale MoS(2) thin layers can be obtained using MoO(3) thin films as a starting material followed by a two-step thermal process, reduction of MoO(3) at 500 °C in hydrogen and sulfurization at 1000 °C in the presence of sulfur. Spectroscopic, optical and electrical characterizations reveal that these films are polycrystalline and with semiconductor properties. The obtained MoS(2) films are uniform in thickness and easily transferable to arbitrary substrates, which make such films suitable for flexible electronics or optoelectronics. PMID:22983609

  13. Nanoparticles of superconducting {gamma}-Mo{sub 2}N and {delta}-MoN

    SciTech Connect

    Gomathi, A.; Sundaresan, A.; Rao, C.N.R.

    2007-01-15

    We have been able to prepare nanoparticles ({approx}4 nm diameter) of cubic {gamma}-Mo{sub 2}N by a simple procedure involving the reaction of MoCl{sub 5} with urea at 873 K. The nanoparticles show a superconducting transition around 6.5 K. The {gamma}-Mo{sub 2}N nanoparticles are readily transformed to nanoparticles of {delta}-MoN with a slightly larger diameter on heating in a NH{sub 3} atmosphere at 573 K. Phase-pure {delta}-MoN obtained by this means shows a superconducting transition around 5 K. - Graphical abstract: TEM image of the {gamma}-Mo{sub 2}N particles with the inset showing the resistivity of the sample as a function of temperature.

  14. In Situ Synthesis of Carbon Nanotube Hybrids with Alternate MoC and MoS2 to Enhance the Electrochemical Activities of MoS2.

    PubMed

    Li, Xin; Zhang, Jinying; Wang, Rui; Huang, Hongyang; Xie, Chong; Li, Zhihui; Li, Jun; Niu, Chunming

    2015-08-12

    Molybdenum disulfides and carbides are effective catalysts for hydrogenation and hydridesulfurization, where MoS2 nanostructures are also highly promising materials for lithium ion batteries. High surface-to-volume ratio and strong interactions with conducting networks are crucial factors for their activities. A new hybrid structure of multiwalled carbon nanotube (MWCNT) with alternate MoC nanoparticles and MoS2 nanosheets (MoS2 + MoC-MWCNT) has been synthesized by controlled carburization of core-shell MoS2-MWCNT hybrid nanotubes and demonstrated by HRTEM, FFT, XRD, and Raman scattering. The MoS2 nanosheets (∼10 nm) remain tightly connected to MWCNT surfaces with {001} planes in parallel to MWCNT walls and the highly crystallized α-MoC particles (∼10 nm) are adhered to MWCNTs at angles of 60-80° between {111} planes and MWCNT walls. The electrochemical performances of the hybrid structures have been demonstrated as anodes for lithium ion batteries to be significantly increased by breaking MoS2 nanotubes into nanosheets (patches) on MWCNT surfaces, especially at high current rates. The specific capacities of MoS2 + MoC-MWCNT sample with ∼23% MoS2 have been demonstrated to be higher than those of MoS2-MWCNTs containing ∼70% MoS2. PMID:26226386

  15. Effect of N addition on tensile and corrosion behaviors of CD4MCU cast duplex stainless steels

    NASA Astrophysics Data System (ADS)

    Son, Jinil; Kim, Sangshik; Lee, Jehyun; Choi, Byunghak

    2003-08-01

    The effect of N addition on the microstructure, tensile, and corrosion behaviors of CD4MCU (Fe-25Cr-5Ni-2.8Cu-2Mo) cast duplex stainless steel was examined in the present study. The slow strain rate tests were also conducted at a nominal strain rate of 1 × 10-6/s in air and 3.5 pct NaCl+5 pct H2SO4 solution for studying the stress corrosion cracking (SCC) behavior. It was observed that the volume fraction of austenitic phase in CD4MCU alloy varied from 38 to 59 pct with increasing nitrogen content from 0 to 0.27 wt. pct. The tensile behavior of CD4MCU cast duplex stainless steels, which tended to vary significantly with different N contents, appeared to be strongly related to the volume changes in ferritic and austenitic phases, rather than the intrinsic N effect. The improvement in the resistance to general corrosion in 3.5 pct NaCl+5 pct H2SO4 aqueous solution was notable with 0.13 pct N addition. The further improvement was not significant with further N addition. The resistance to SCC of CD4MCU cast duplex stainless steels in 3.5 pct NaCl+5 pct H2SO4 aqueous solution, however, increased continuously with increasing N content. The enhancement in the SCC resistance was believed to be related to the volume fraction of globular austenitic colonies, which tended to act as barriers for the development of initial pitting cracks in the ferritic phase into the sharp ones.

  16. Detection of secondary phases in duplex stainless steel by magnetic force microscopy and scanning Kelvin probe force microscopy

    SciTech Connect

    Ramírez-Salgado, J.; Domínguez-Aguilar, M.A.; Castro-Domínguez, B.; Hernández-Hernández, P.; Newman, R.C.

    2013-12-15

    The secondary phase transformations in a commercial super duplex stainless steel were investigated by micro-chemical analyses and high resolution scanning probe microscopy. Energy dispersive X-ray and electron probe detected ferrite and austenite as well as secondary phases in unetched aged duplex stainless steel type 25Cr-7Ni-3Mo. Volta potential indicated that nitride and sigma appeared more active than ferrite, while secondary austenite and austenite presented a nobler potential. Reversal order in nobility is thought to be attributable to the potential ranking provided by oxide nature diversity as a result of secondary phase surface compositions on steel. After eutectoid transformation, secondary austenite was detected by electron probe microanalysis, whereas atomic force microscopy distinguished this phase from former austenite by image contrast. Magnetic force microscopy revealed a “ghosted” effect on the latter microstructure probably derived from metal memory reminiscence of mechanical polishing at passivity and long range magnetic forces of ferrite phase. - Highlights: • Nobility detection of secondary phases by SKPFM in DSS particles is not a straightforward procedure. • As Volta potential and contrast are not always consistent SKPFM surface oxides is thought played an important role in detection. • AFM distinguished secondary austenite from former austenite by image contrast though SEM required EPMA.

  17. Effect of thermal treatment on the corrosion resistance of Type 316L stainless steel exposed in supercritical water

    NASA Astrophysics Data System (ADS)

    Jiao, Y.; Zheng, W.; Guzonas, D. A.; Cook, W. G.; Kish, J. R.

    2015-09-01

    There are still unknown aspects about the growth mechanism of oxide scales formed on candidate stainless steel fuel cladding materials during exposure in supercritical water (SCW) under the conditions relevant to the Canadian supercritical water-cooled reactor (SCWR). The tendency for intermetallic precipitates to form within the grains and on grain boundaries during prolonged exposure at high temperatures represents an unknown factor to corrosion resistance, since they tend to bind alloyed Cr. The objective of this study was to better understand the extent to which intermetallic precipitates affects the mode and extent of corrosion in SCW. Type 316L stainless steel, used as a model Fe-Cr-Ni-Mo alloy, was exposed to 25 MPa SCW at 550 °C for 500 h in a static autoclave for this purpose. Mechanically-abraded samples were tested in the mill-annealed (MA) and a thermally-treated (TT) condition. The thermal treatment was conducted at 815 °C for 1000 h to precipitate the carbide (M23C6), chi (χ), laves (η) and sigma (σ) phases. It was found that although relatively large intermetallic precipitates formed at the scale/alloy interface locally affected the oxide scale formation, their discontinuous formation did not affect the short-term overall apparent corrosion resistance.

  18. Overview of strategies for high-temperature creep and oxidation resistance of alumina-forming austenitic stainless steels

    SciTech Connect

    Yamamoto, Yukinori; Brady, Michael P; Santella, Michael L; Bei, Hongbin; Maziasz, Philip J; Pint, Bruce A

    2011-01-01

    A family of creep-resistant, alumina-forming austenitic (AFA) stainless steel alloys is under development for structural use in fossil energy conversion and combustion system applications. The AFA alloys developed to date exhibit comparable creep-rupture lives to state-of-the-art advanced austenitic alloys, and superior oxidation resistance in the {approx}923 K to 1173 K (650 C to 900 C) temperature range due to the formation of a protective Al{sub 2}O{sub 3} scale rather than the Cr{sub 2}O{sub 3} scales that form on conventional stainless steel alloys. This article overviews the alloy design approaches used to obtain high-temperature creep strength in AFA alloys via considerations of phase equilibrium from thermodynamic calculations as well as microstructure characterization. Strengthening precipitates under evaluation include MC-type carbides or intermetallic phases such as NiAl-B2, Fe{sub 2}(Mo,Nb)-Laves, Ni{sub 3}Al-L1{sub 2}, etc. in the austenitic single-phase matrix. Creep, tensile, and oxidation properties of the AFA alloys are discussed relative to compositional and microstructural factors.

  19. The Perturbational MO Method for Saturated Systems.

    ERIC Educational Resources Information Center

    Herndon, William C.

    1979-01-01

    Summarizes a theoretical approach using nonbonding MO's and perturbation theory to correlate properties of saturated hydrocarbons. Discussion is limited to correctly predicted using this method. Suggests calculations can be carried out quickly in organic chemistry. (Author/SA)

  20. Sunset at the ALaMO

    NASA Video Gallery

    A new color all-sky camera has opened its eyes at the ALaMO, or Automated Lunar and Meteor Observatory, at NASA's Marshall Space Flight Center in Huntsville, Ala. Watch its inaugural video below, s...

  1. 78 FR 48762 - Missouri Disaster #MO-00065

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-09

    ... From the Federal Register Online via the Government Publishing Office SMALL BUSINESS ADMINISTRATION Missouri Disaster MO-00065 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY.... ADDRESSES: Submit completed loan applications to: U.S. Small Business Administration, Processing...

  2. 76 FR 72020 - Missouri Disaster #MO-00051

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-11-21

    ... From the Federal Register Online via the Government Publishing Office SMALL BUSINESS ADMINISTRATION Missouri Disaster MO-00051 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY.../2011. Incident: Severe storms, straight line winds, tornadoes and flooding. Incident Period:...

  3. Reaction mechanism of core–shell MoO2/MoS2 nanoflakes via plasma-assisted sulfurization of MoO3

    NASA Astrophysics Data System (ADS)

    Kumar, Prabhat; Singh, Megha; Sharma, Rabindar K.; Reddy, G. B.

    2016-05-01

    The sulfurization of MoO3 in an H2S/Ar plasma atmosphere has been experimentally studied and a reaction mechanism has been proposed based on the results obtained. Nanostructured thin films (NTFs) of MoO3 were sulfurized at different temperatures varying from 150 °C to 550 °C. High-resolution transmission electron microscopy (TEM) images depict core–shell nanoflakes with varying shell thicknesses as the sulfurization temperature (T sn) is varied. The shells consist of MoS2 and the core is MoO2/MoO3. X-ray diffraction (XRD) and Raman analysis have been used to study the structural changes as MoO3 is sulfurized. The analyses showed two phases, MoO2 and MoS2, at low temperatures (≤350 °C), whereas the films sulfurized at higher temperatures show predominantly MoS2. The scanning electron microscopy (SEM) results show no noticeable changes in the surface morphology of the NTFs after sulfurization. X-ray photoelectron spectroscopy (XPS) was carried out to calculate the relative percentages of MoO3, MoO2 and MoS2. It is revealed that sulfurization of MoO3 in the plasma is affected by T sn. The sulfurization process occurs in two steps, involving the reduction of MoO3 to form MoO2 in the first step, followed by MoO2 being converted into MoS2. It is also evident that the reduction of MoO3 is more a result of the reactive species of hydrogen (H*) than the replacement of oxygen by sulfur in the second step.

  4. Weldable, age hardenable, austenitic stainless steel

    DOEpatents

    Brooks, J.A.; Krenzer, R.W.

    1975-07-22

    An age hardenable, austenitic stainless steel having superior weldability properties as well as resistance to degradation of properties in a hydrogen atmosphere is described. It has a composition of from about 24.0 to about 34.0 weight percent (w/o) nickel, from about 13.5 to about 16.0 w/o chromium, from about 1.9 to about 2.3 w/o titanium, from about 1.0 to about 1.5 w/ o molybdenum, from about 0.01 to about 0.05 w/o carbon, from about 0 to about 0.25 w/o manganese, from about 0 to about 0.01 w/o phosphorous and preferably about 0.005 w/o maximum, from about 0 to about 0.010 w/o sulfur and preferably about 0.005 w/o maximum, from about 0 to about 0.25 w/o silicon, from about 0.1 to about 0.35 w/o aluminum, from about 0.10 to about 0.50 w/o vanadium, from about 0 to about 0.0015 w/o boron, and the balance essentially iron. (auth)

  5. Instabilities in stabilized austenitic stainless steels

    NASA Astrophysics Data System (ADS)

    Ayer, Raghavan; Klein, C. F.; Marzinsky, C. N.

    1992-09-01

    The effect of aging on the precipitation of grain boundary phases in three austenitic stainless steels (AISI 347, 347AP, and an experimental steel stabilized with hafnium) was investigated. Aging was performed both on bulk steels as well as on samples which were subjected to a thermal treatment to simulate the coarse grain region of the heat affected zone (HAZ) during welding. Aging of the bulk steels at 866 K for 8000 hours resulted in the precipitation of Cr23C6 carbides, σ, and Fe2Nb phases; the propensity for precipitation was least for the hafnium-stabilized steel. Weld simulation of the HAZ resulted in dissolution of the phases present in the as-received 347 and 347AP steels, leading to grain coarsening. Subsequent aging caused extensive grain boundary Cr23C6 carbides and inhomogeneous matrix precipitation. In addition, steel 347AP formed a precipitate free zone (PFZ) along the grain boundaries. The steel containing hafnium showed the best microstructural stability to aging and welding.

  6. NanoComposite Stainless Steel Powder Technologies

    SciTech Connect

    DeHoff, R.; Glasgow, C.

    2012-07-25

    Oak Ridge National Laboratory has been investigating a new class of Fe-based amorphous material stemming from a DARPA, Defense Advanced Research Projects Agency initiative in structural amorphous metals. Further engineering of the original SAM materials such as chemistry modifications and manufacturing processes, has led to the development of a class of Fe based amorphous materials that upon processing, devitrify into a nearly homogeneous distribution of nano sized complex metal carbides and borides. The powder material is produced through the gas atomization process and subsequently utilized by several methods; laser fusing as a coating to existing components or bulk consolidated into new components through various powder metallurgy techniques (vacuum hot pressing, Dynaforge, and hot isostatic pressing). The unique fine scale distribution of microstructural features yields a material with high hardness and wear resistance compared to material produced through conventional processing techniques such as casting while maintaining adequate fracture toughness. Several compositions have been examined including those specifically designed for high hardness and wear resistance and a composition specifically tailored to devitrify into an austenitic matrix (similar to a stainless steel) which poses improved corrosion behavior.

  7. Weldability of neutron irradiated austenitic stainless steels

    NASA Astrophysics Data System (ADS)

    Asano, Kyoichi; Nishimura, Seiji; Saito, Yoshiaki; Sakamoto, Hiroshi; Yamada, Yuji; Kato, Takahiko; Hashimoto, Tsuneyuki

    1999-01-01

    Degradation of weldability in neutron irradiated austenitic stainless steel is an important issue to be addressed in the planning of proactive maintenance of light water reactor core internals. In this work, samples selected from reactor internal components which had been irradiated to fluence from 8.5 × 10 22 to 1.4 × 10 26 n/m 2 ( E > 1 MeV) corresponding to helium content from 0.11 to 103 appm, respectively, were subjected to tungsten inert gas arc (TIG) welding with heat input ranged 0.6-16 kJ/cm. The weld defects were characterized by penetrant test and cross-sectional metallography. The integrity of the weld was better when there were less helium and at lower heat input. Tensile properties of weld joint containing 0.6 appm of helium fulfilled the requirement for unirradiated base metal. Repeated thermal cycles were found to be very hazardous. The results showed the combination of material helium content and weld heat input where materials can be welded with little concern to invite cracking. Also, the importance of using properly selected welding procedures to minimize thermal cycling was recognized.

  8. Welding Behavior of Free Machining Stainless Steel

    SciTech Connect

    BROOKS,JOHN A.; ROBINO,CHARLES V.; HEADLEY,THOMAS J.; MICHAEL,JOSEPH R.

    2000-07-24

    The weld solidification and cracking behavior of sulfur bearing free machining austenitic stainless steel was investigated for both gas-tungsten arc (GTA) and pulsed laser beam weld processes. The GTA weld solidification was consistent with those predicted with existing solidification diagrams and the cracking response was controlled primarily by solidification mode. The solidification behavior of the pulsed laser welds was complex, and often contained regions of primary ferrite and primary austenite solidification, although in all cases the welds were found to be completely austenite at room temperature. Electron backscattered diffraction (EBSD) pattern analysis indicated that the nature of the base metal at the time of solidification plays a primary role in initial solidification. The solid state transformation of austenite to ferrite at the fusion zone boundary, and ferrite to austenite on cooling may both be massive in nature. A range of alloy compositions that exhibited good resistance to solidification cracking and was compatible with both welding processes was identified. The compositional range is bounded by laser weldability at lower Cr{sub eq}/Ni{sub eq} ratios and by the GTA weldability at higher ratios. It was found with both processes that the limiting ratios were somewhat dependent upon sulfur content.

  9. Suspended MoS2 devices

    NASA Astrophysics Data System (ADS)

    Jin, Taiyu; Kang, Jinyoung; Liu, Renlong; Kim, Youngchan; Lee, Changgu

    2013-03-01

    Single or a few layer MoS2 sheets have been reported to have high electric mobility and current on/off ratio comparable to those of silicon due to its semiconductor properties with bandgap of 1.3 ~ 1.9eV. However, its extremely high surface to volume ratio and low thickness prohibits it from reproducing its electronic properties on SiO2 substrates possibly because of charge scattering by surface charges and phonons. In order to investigate these surface effects, we fabricated MoS2 devices suspended from the SiO2 and characterized their electronic transport properties. We exfoliated single or a few layer MoS2 on SiO2 substrates first, and fabricated field effect transistors using e-beam lithography. After that, we suspended MoS2 sheets by etching SiO2 with hydrofluoric acid. We measured mobility and current on/off ratio before and after the etching process. We found that mobility of MoS2 devices increased by factor of 5-10 after etching for all devices. However, on/off ratio did not show significant variation. Our measurements suggest that atomically thin MoS2 devices are significantly affected by substrate surface and environment.

  10. Stainless steel tube-based cell cryopreservation containers.

    PubMed

    Shih, Wei-Hung; Yu, Zong-Yan; Wu, Wei-Te

    2013-12-01

    This study focused on increasing the freezing rate in cell vitrification cryopreservation by using a cryopreservation container possessing rigid mechanical properties and high heat-transfer efficiency. Applying a fast freezing rate in vitrification cryopreservation causes a rapid temperature change in the cryopreservation container and has a substantial impact on mechanical properties; therefore, a highly rigid cryopreservation container that possesses a fast freezing rate must be developed. To produce a highly rigid cryopreservation container possessing superior heat transfer efficiency, this study applies an electrochemical machining (ECM) method to an ANSI 316L stainless steel tube to treat the surface material by polishing and roughening, thereby increasing the freezing rate and reducing the probability of ice crystal formation. The results indicated that the ECM method provided high-quality surface treatment of the stainless steel tube. This method can reduce internal surface roughness in the stainless steel tube, thereby reducing the probability of ice crystal formation, and increase external surface roughness, consequently raising convection heat-transfer efficiency. In addition, by thinning the stainless steel tube, this method reduces heat capacity and thermal resistance, thereby increasing the freezing rate. The freezing rate (3399 ± 197 °C/min) of a stainless steel tube after interior and exterior polishing and exterior etching by applying ECM compared with the freezing rate (1818 ± 54 °C/min) of an original stainless steel tube was increased by 87%, which also exceeds the freezing rate (2015 ± 49 °C/min) of an original quartz tube that has a 20% lower heat capacity. However, the results indicated that increasing heat-transferring surface areas and reducing heat capacities cannot effectively increase the freezing rate of a stainless steel tube if only one method is applied; instead, both techniques must be implemented concurrently to improve the

  11. Antibacterial effect of silver nanofilm modified stainless steel surface

    NASA Astrophysics Data System (ADS)

    Fang, F.; Kennedy, J.; Dhillon, M.; Flint, S.

    2015-03-01

    Bacteria can attach to stainless steel surfaces, resulting in the colonization of the surface known as biofilms. The release of bacteria from biofilms can cause contamination of food such as dairy products in manufacturing plants. This study aimed to modify stainless steel surfaces with silver nanofilms and to examine the antibacterial effectiveness of the modified surface. Ion implantation was applied to produce silver nanofilms on stainless steel surfaces. 35 keV Ag ions were implanted with various fluences of 1 × 1015 to 1 × 1017 ions•cm-2 at room temperature. Representative atomic force microscopy characterizations of the modified stainless steel are presented. Rutherford backscattering spectrometry spectra revealed the implanted atoms were located in the near-surface region. Both unmodified and modified stainless steel coupons were then exposed to two types of bacteria, Pseudomonas fluorescens and Streptococcus thermophilus, to determine the effect of the surface modification on bacterial attachment and biofilm development. The silver modified coupon surface fluoresced red over most of the surface area implying that most bacteria on coupon surface were dead. This study indicates that the silver nanofilm fabricated by the ion implantation method is a promising way of reducing the attachment of bacteria and delay biofilm formation.

  12. Investigation of the diffusion kinetics of borided stainless steels

    NASA Astrophysics Data System (ADS)

    Kayali, Yusuf

    2013-12-01

    In this study, the kinetics of borides formed on AISI 420, AISI 304 and AISI 304L stainless steels was investigated. Boronizing treatment was carried out using Ekabor-II powders at the processing temperatures of 1123, 1173 and 1223 K for 2, 4 and 6 h. The phases of the boride layers of borided AISI 420, AISI 304 and AISI 304L stainless steels were FeB, Fe2B, CrB and NiB, respectively. The thickness of the boride layer formed on the borided steels ranged from 4.6 to 64 μm depending on the boriding temperature, boriding time and alloying elements of the stainless steels. Depending on the chemical composition, temperature and layer thickness, the activation energies of boron in AISI 420, AISI 304 and AISI 304L stainless steels were found to be 206.161, 234.641 and 222.818 kJ/mol, respectively. The kinetics of growth of the boride layers formed on the AISI 420, AISI 304 and AISI 304L stainless steels and the thickness of the boride layers were investigated.

  13. Work of adhesion of dairy products on stainless steel surface

    PubMed Central

    Bernardes, Patrícia Campos; Araújo, Emiliane Andrade; dos Santos Pires, Ana Clarissa; Queiroz Fialho Júnior, José Felício; Lelis, Carini Aparecida; de Andrade, Nélio José

    2012-01-01

    The adhesion of the solids presents in food can difficult the process of surface cleaning and promotes the bacterial adhesion process and can trigger health problems. In our study, we used UHT whole milk, chocolate based milk and infant formula to evaluate the adhesion of Enterobacter sakazakii on stainless steel coupons, and we determine the work of adhesion by measuring the contact angle as well as measured the interfacial tension of the samples. In addition we evaluated the hydrophobicity of stainless steel after pre-conditioning with milk samples mentioned. E. sakazakii was able to adhere to stainless steel in large numbers in the presence of dairy products. The chocolate based milk obtained the lower contact angle with stainless steel surface, higher interfacial tension and consequently higher adhesion work. It was verified a tendency of decreasing the interfacial tension as a function of the increasing of protein content. The preconditioning of the stainless steel coupons with milk samples changed the hydrophobic characteristics of the surfaces and became them hydrophilic. Therefore, variations in the composition of the milk products affect parameters important that can influence the procedure of hygiene in surface used in food industry. PMID:24031951

  14. A stainless steel bracket for orthodontic application.

    PubMed

    Oh, Keun-Taek; Choo, Sung-Uk; Kim, Kwang-Mahn; Kim, Kyoung-Nam

    2005-06-01

    Aesthetics has become an essential element when choosing orthodontic fixed appliances. Most metallic brackets used in orthodontic therapy are made from stainless steel (SS) with the appropriate physical properties and good corrosion resistance, and are available as types 304, 316 and 17-4 PH SS. However, localized corrosion of these materials can frequently occur in the oral environment. This study was undertaken to evaluate the accuracy of sizing, microstructure, hardness, corrosion resistance, frictional resistance and cytotoxicity of commercially available Mini-diamond (S17400), Archist (S30403) and experimentally manufactured SR-50A (S32050) brackets. The size accuracy of Mini-diamond was the highest at all locations except for the external horizontal width of the tie wing (P < 0.05). Micrographs of the Mini-diamond and Archist showed precipitates in the grains and around their boundaries. SR-50A showed the only austenitic phase and the highest polarization resistance of the tested samples. SR-50A also had the highest corrosion resistance [SR-50A, Mini-diamond and Archist were 0.9 x 10(-3), 3.7 x 10(-3), and 7.4 x 10(-3) mm per year (mpy), respectively], in the artificial saliva. The frictional force of SR-50A decreased over time, but that of Mini-diamond and Archist increased. Therefore, SR-50A is believed to have better frictional properties to orthodontic wire than Mini-diamond and Archist. Cytotoxic results showed that the response index of SR-50A was 0/1 (mild), Mini-diamond 1/1 (mild+), and Archist 1/2 (mild+). SR-50A showed greater biocompatibility than either Mini-diamond or Archist. It is concluded that the SR-50A bracket has good frictional property, corrosion resistance and biocompatibility with a lower probability of allergic reaction, compared with conventionally used SS brackets. PMID:15947222

  15. Study of tribological behavior of Cu-MoS2 and Ag-MoS2 nanocomposite lubricants.

    PubMed

    An, V; Anisimov, E; Druzyanova, V; Burtsev, N; Shulepov, I; Khaskelberg, M

    2016-01-01

    Tribological behavior of Cu-MoS2 and Ag-MoS2 nanocomposite lubricant was studied. Cu nanoparticles produced by electrical explosion of copper wires and Ag nanoparticles prepared by electrospark erosion were employed as metal cladding modifiers of MoS2 nanolamellar particles. The tribological tests showed Cu-MoS2 and Ag-MoS2 nanocomposite lubricants changed the friction coefficient of the initial grease and essentially improved its wear resistance. PMID:26837277

  16. Tensile flow and work-hardening behavior of a Ti-modified austenitic stainless steel

    SciTech Connect

    Sivaprasad, P.V.; Venugopal, S.; Venkadesan, S.

    1997-01-01

    The flow-stress data of a 15Cr-15Ni-2.2Mo-Ti modified austenitic stainless steel in the temperature range 300 to 1,023 K was analyzed in terms of Ludwigson and Voce equations. The parameters of these equations were critically examined with respect to the effect of Ti/C ratio and test temperature. It was found that the Ludwigson equation described the flow behavior adequately up to the test temperature of 923 K, whereas the Voce equation could be employed in the full temperature range. The peaks/plateaus observed in the variation of these parameters as a function of temperature in the intermediate temperature range have been identified as one of the manifestations of dynamic strain aging (DSA). Also, the variation of these parameters with temperature clearly could bring out the different domains of DSA observed in this alloy. The work-hardening analysis of the flow-stress data revealed that in the DSA regime, the onset of stage III hardening is athermal.

  17. Precipitation and Phase Transformations in 2101 Lean Duplex Stainless Steel During Isothermal Aging

    NASA Astrophysics Data System (ADS)

    Maetz, Jean-Yves; Cazottes, Sophie; Verdu, Catherine; Kleber, Xavier

    2016-01-01

    The effect of isothermal aging at 963 K (690 °C) on the microstructure of a 2101 lean duplex stainless steel, with the composition Fe-21.5Cr-5Mn-1.6Ni-0.22N-0.3Mo, was investigated using a multi-technique and multi-scale approach. The kinetics of phase transformation and precipitation was followed from a few minutes to thousands of hours using thermoelectric power measurements; based on these results, certain aging states were selected for electron microscopy characterization. Scanning electron microscopy, electron back-scattered diffraction, and transmission electron microscopy were used to quantitatively describe the microstructural evolution through crystallographic analysis, chemical analysis, and volume fraction measurements from the macroscopic scale down to the nanometric scale. During aging, the precipitation of M23C6 carbides, Cr2N nitrides, and σ phase as well as the transformation of ferrite into austenite and austenite into martensite was observed. These complex microstructural changes are controlled by Cr volume diffusion. The precipitation and phase transformation mechanisms are described.

  18. Automatic assessment of a two-phase structure in the duplex stainless-steel SAF 2205

    SciTech Connect

    Komenda, J. ); Sandstroem, R. )

    1993-10-01

    Automatic image analysis was used to study the effect of deformation on the size and distribution of the austenite and ferrite phases in the duplex stainless steel SAF 2205 (22Cr-5Ni-3Mo-15N). The main parameters used were the chord size to characterize the ferrite phase and Feret's diameter for the austenite phase. As the deformation increased, ferrite bands became more elongated and thinner, contributing to a pronounced banding. The amount of banding can be quantified by using a ratio between the slopes of the chord size distributions in the longitudinal and short transverse directions. According to a proposed model of the influence of deformation on the two-phase structure, the process of austenite elongation and subdivision of austenite islands (crushing) is described. The effect of deformation on the yield and tensile strength was expressed using a Hall-Petch type relationship where the grain size was represented by the average width of the ferrite bands. The observed anisotropy in strength properties is believed to be due to texture hardening. Because elongation at a given strength level is the same in both the longitudinal and transverse directions, the banding itself does not influence the ductility. Nor can the strength anisotropy be due to banding, because the strength is greater in the longitudinal than in the transverse direction.

  19. Development and Exploratory Scale-Up of Alumina-Forming Austenitic (AFA) Stainless Steels

    SciTech Connect

    Brady, Michael P; Magee, John H; Yamamoto, Yukinori; Maziasz, Philip J; Santella, Michael L; Pint, Bruce A; Bei, Hongbin

    2009-01-01

    This paper presents the results of the continued development of creep-resistant, alumina-forming austenitic (AFA) stainless steel alloys, which exhibit a unique combination of excellent oxidation resistance via protective alumina (Al2O3) scale formation and high-temperature creep strength through the formation of stable nano-scale MC carbides and intermetallic precipitates. Efforts in fiscal year 2009 focused on the characterization and understanding of long-term oxidation resistance and tensile properties as a function of alloy composition and microstructure. Computational thermodynamic calculations of the austenitic matrix phase composition and the volume fraction of MC, B2-NiAl, and Fe2(Mo,Nb) base Laves phase precipitates were used to interpret oxidation behavior. Of particular interest was the enrichment of Cr in the austenitic matrix phase by additions of Nb, which aided the establishment and maintenance of alumina. Higher levels of Nb additions also increased the volume fraction of B2-NiAl precipitates, which served as an Al reservoir during long-term oxidation. Ageing studies of AFA alloys were conducted at 750C for times up to 2000 h. Ageing resulted in near doubling of yield strength at room temperature after only 50 h at 750C, with little further increase in yield strength out to 2000 h of ageing. Elongation was reduced on ageing; however, levels of 15-25% were retained at room temperature after 2000 h of total ageing.

  20. Effect of alloying elements on stress corrosion cracking of stainless alloys

    SciTech Connect

    Streicher, M.A.

    1997-11-01

    Long-time stress corrosion cracking tests were made in boiling, 45% magnesium chloride (MgCl{sub 2}) solution at 155 C and in an autoclave, 26% sodium chloride (NaCl) solution at 200 C on 15 commercial stainless steel and Ni-based alloys and four laboratory Fe-Cr-Ni heats. The results were compared with the original Copson curve derived from tests in the MgCl{sub 2} solution on wires made from Fe-20% Cr alloys with a range of Ni contents. Additional alloying elements in commercial alloys (Mo, Cu, Ti, Cb) do not have a significant effect on the Copson curve. In contrast, in the less severe NaCl tests, times to failure were greatly increased and the range of Ni concentration in which alloys are susceptible to cracking was narrowed, even in 100-day tests. The significant of this information on the effect of Ni in cases of exceedingly long service times, such as for containers for high-level nuclear waste, is discussed.

  1. Interface segregation behavior in thermal aged austenitic precipitation strengthened stainless steel.

    PubMed

    Li, Hui; Song, Hui; Liu, Wenqing; Xia, Shuang; Zhou, Bangxin; Su, Cheng; Ding, Wenyan

    2015-12-01

    The segregation of various elements at grain boundaries, precipitate/matrix interfaces were analyzed using atom probe tomography in an austenitic precipitation strengthened stainless steel aged at 750 °C for different time. Segregation of P, B and C at all types of interfaces in all the specimens were observed. However, Si segregated at all types of interfaces only in the specimen aged for 16 h. Enrichment of Ti at grain boundaries was evident in the specimen aged for 16 h, while Ti did not segregate at other interfaces. Mo varied considerably among interface types, e.g. from segregated at grain boundaries in the specimens after all the aging time to never segregate at γ'/γ phase interfaces. Cr co-segregated with C at grain boundaries, although carbides still did not nucleate at grain boundaries yet. Despite segregation tendency variations in different interface types, the segregation tendency evolution variation of different elements depending aging time were analyzed among all types of interfaces. Based on the experimental results, the enrichment factors, Gibbs interface excess and segregation free energies of segregated elements were calculated and discussed. PMID:26142697

  2. Formation quality optimization of laser hot wire cladding for repairing martensite precipitation hardening stainless steel

    NASA Astrophysics Data System (ADS)

    Wen, Peng; Feng, Zhenhua; Zheng, Shiqing

    2015-01-01

    Laser cladding is an advantaged repairing technology due to its low heat input and high flexibility. With preheating wire by resistance heat, laser hot wire cladding shows better process stability and higher deposition efficiency compared to laser cold wire/powder cladding. Multi-pass layer were cladded on the surface of martensite precipitation hardening stainless steel FV520B by fiber laser with ER410NiMo wire. Wire feed rate and preheat current were optimized to obtain stable wire transfer, which guaranteed good formation quality of single pass cladding. Response surface methodology (RSM) was used to optimize processing parameters and predict formation quality of multi-pass cladding. Laser power P, scanning speed Vs, wire feed rate Vf and overlap ratio η were selected as the input variables, while flatness ratio, dilution and incomplete fusion value as the responses. Optimal clad layer with flat surface, low dilution and no incomplete fusion was obtained by appropriately reducing Vf, and increasing P, Vs and η. No defect like pore or crack was found. The tensile strength and impact toughness of the clad layer is respectively 96% and 86% of those of the substrate. The clad layer showed nonuniform microstructure and was divided into quenched areas with coarse lath martensite and tempered areas with tempered martensite due to different thermal cycles in adjacent areas. The tempered areas showed similar hardness to the substrate.

  3. Selection of stainless steel tubes to minimize hot corrosion in utility boilers

    SciTech Connect

    Fujikawa, H.; Makiura, H.

    1982-12-01

    Austenitic stainless steel tubes of AISI 304, 316, 321, and 347 types are sometimes exposed to severe hot corrosion environments in superheaters and reheaters of utility boilers. Hot corrosion depends on the existence of V/sub 2/O/sub 5/ and Na/sub 2/SO/sub 4/ in the oil-fired boilers, and of Na/sub 2/SO/sub 4/ and K/sub 2/SO/sub 4/ in the coal-fired boilers. Among various kinds of ash corrosions, the alkali sulphate-side corrosion has been mainly studied. Type 347 steel better resistance to alkali sulphate-side corrosion than 304, 316, and 321 steels. Alloying with Nb was more effective than Mo or Ti. A (Cr, Fe, Ni)-spinel oxide layer with little ash content formed at the scale-metal interface in 347 steel. In field tests, 347 tubes have maintained good resistance to both fire-side and steam-side corrosion for five years. However, 321 tubes were removed after three years of service, because of severe fire-side corrosion.

  4. High stored-energy breakdown tests on electrodes made of stainless steel, copper, titanium and molybdenum

    SciTech Connect

    Esch, H. P. L. de Simonin, A.; Grand, C.

    2015-04-08

    IRFM have conducted resilience tests on electrodes made of Cu, stainless steel 304L, Ti and Mo against breakdowns up to 170 kV and 300 J. The tests of the 10×10 cm{sup 2} electrodes have been performed at an electrode distance d=11 mm under vacuum (P∼5×10{sup −6} mbar). No great difference in voltage holding between the materials could be identified; all materials could reach a voltage holding between 140 and 170 kV over the 11 mm gap, i.e. results scatter within a ±10% band. After exposure to ∼10000 seconds of high-voltage (HV) on-time, having accumulated ∼1000 breakdowns, the electrodes were inspected. The anodes were covered with large and small craters. The rugosity of the anodes had increased substantially, that of the cathodes to a lesser extent. The molybdenum electrodes are least affected, but this does not show in their voltage holding capability. It is hypothesized that penetrating high-energy electrons from the breakdown project heat below the surface of the anode and cause a micro-explosion of material when melting point is exceeded. Polished electrodes have also been tested. The polishing results in a substantially reduced breakdown rate in the beginning, but after having suffered a relatively small number (∼100) of breakdowns, the polished electrodes behaved the same as the unpolished ones.

  5. High Nb, Ta, and Al creep- and oxidation-resistant austenitic stainless steel

    DOEpatents

    Brady, Michael P [Oak Ridge, TN; Santella, Michael L [Knoxville, TN; Yamamoto, Yukinori [Oak Ridge, TN; Liu, Chain-tsuan [Oak Ridge, TN

    2010-07-13

    An austenitic stainless steel HTUPS alloy includes, in weight percent: 15 to 30 Ni; 10 to 15 Cr; 2 to 5 Al; 0.6 to 5 total of at least one of Nb and Ta; no more than 0.3 of combined Ti+V; up to 3 Mo; up to 3 Co; up to 1 W; up to 0.5 Cu; up to 4 Mn; up to 1 Si; 0.05 to 0.15 C; up to 0.15 B; up to 0.05 P; up to 1 total of at least one of Y, La, Ce, Hf, and Zr; less than 0.05 N; and base Fe, wherein the weight percent Fe is greater than the weight percent Ni wherein said alloy forms an external continuous scale comprising alumina, nanometer scale sized particles distributed throughout the microstructure, said particles comprising at least one composition selected from the group consisting of NbC and TaC, and a stable essentially single phase fcc austenitic matrix microstructure, said austenitic matrix being essentially delta-ferrite-free and essentially BCC-phase-free.

  6. High stored-energy breakdown tests on electrodes made of stainless steel, copper, titanium and molybdenum

    NASA Astrophysics Data System (ADS)

    de Esch, H. P. L.; Simonin, A.; Grand, C.

    2015-04-01

    IRFM have conducted resilience tests on electrodes made of Cu, stainless steel 304L, Ti and Mo against breakdowns up to 170 kV and 300 J. The tests of the 10×10 cm2 electrodes have been performed at an electrode distance d=11 mm under vacuum (P˜5×10-6 mbar). No great difference in voltage holding between the materials could be identified; all materials could reach a voltage holding between 140 and 170 kV over the 11 mm gap, i.e. results scatter within a ±10% band. After exposure to ˜10000 seconds of high-voltage (HV) on-time, having accumulated ˜1000 breakdowns, the electrodes were inspected. The anodes were covered with large and small craters. The rugosity of the anodes had increased substantially, that of the cathodes to a lesser extent. The molybdenum electrodes are least affected, but this does not show in their voltage holding capability. It is hypothesized that penetrating high-energy electrons from the breakdown project heat below the surface of the anode and cause a micro-explosion of material when melting point is exceeded. Polished electrodes have also been tested. The polishing results in a substantially reduced breakdown rate in the beginning, but after having suffered a relatively small number (˜100) of breakdowns, the polished electrodes behaved the same as the unpolished ones.

  7. Improved austenitic stainless steel for high temperature applications. [Improved stress-rupture properties

    DOEpatents

    Not Available

    This invention describes a composition for an austenitic stainless steel which has been found to exhibit improved high temperature stress rupture properties. The composition of this alloy is about (in wt. %): 12.5 to 14.5 Cr; 14.5 to 16.5 Ni; 1.5 to 2.5 Mo; 1.5 to 2.5 Mn; 0.1 to 0.4 Ti; 0.02 to 0.08 C; 0.5 to 1.0 Si; 0.01 maximum, N; 0.02 to 0.08 P; 0.002 to 0.008 B; 0.004-0.010 S; 0.02-0.05 Nb; .01-.05 V; 0.005-0.02 Ta; 0.02-0.05 Al; 0.01-0.04 Cu; 0.02-0.05 Co; .03 maximum, As; 0.01 maximum, 0; 0.01 maximum, Zr; and with the balance of the alloy being essentially iron. The carbon content of the alloy is adjusted such that wt. % Ti/(wt. % C+wt. % N) is between 4 and 6, and most preferably about 5. In addition the sum of the wt. % P + wt. % B + wt. % S is at least 0.03 wt. %. This alloy is believed to be particularly well suited for use as fast breeder reactor fuel element cladding.

  8. Effect of Aging Treatment on Impact Toughness and Corrosion Resistance of Super Duplex Stainless Steel

    NASA Astrophysics Data System (ADS)

    Kim, Jae-Hwan; Oh, Eun-Ji; Lee, Byung-Chan; Kang, Chang-Yong

    2016-01-01

    The effect of aging time on impact toughness and corrosion resistance of 25%Cr-7%Ni-2%Mo-4%W-0.2%N super duplex stainless steel from the viewpoint of intermetallic secondary phase variation was investigated with scanning electron microscopic observation with energy-dispersive x-ray spectroscopic analysis and transmission electron microscopy. The results clarified that R-phase is precipitated not only at the interface of ferrite and austenite but inside the ferrite at an initial stage of aging and then transformed into σ-phase from an aging time of 1 h, while the ferrite phase decomposed into γ2 and σ-phase with increase of aging time. This variation of the phases led to decrease of its impact toughness, and specifically, the R-phase was proved to be predominant in the degradation of the impact toughness at the initial stage of the aging. Additionally, these secondary phases led to deterioration of corrosion resistance because of Cr depletion.

  9. Direct observation and quantification of nanoscale spinodal decomposition in super duplex stainless steel weld metals.

    PubMed

    Shariq, Ahmed; Hättestrand, Mats; Nilsson, Jan-Olof; Gregori, Andrea

    2009-06-01

    Three variants of super duplex stainless steel weld metals with the basic composition 29Cr-8Ni-2Mo (wt%) were investigated. The nitrogen content of the three materials was 0.22%, 0.33% and 0.37%, respectively. Isothermal heat treatments were performed at 450 degrees C for times up to 243 h. The hardness evolution of the three materials was found to vary with the overall concentration of the nitrogen. Atom probe field ion microscopy (APFIM) was used to directly detect and quantify the degree of spinodal decomposition in different material conditions. 3-DAP atomic reconstruction clearly illustrate nanoscale variation of iron rich (alpha) and chromium rich (alpha') phases. A longer ageing time produces a coarser microstructure with larger alpha and alpha' domains. Statistical evaluation of APFIM data showed that phase separation was significant already after 1 h of ageing that gradually became more pronounced. Although nanoscale concentration variation was evident, no significant influence of overall nitrogen content on the degree of spinodal decomposition was found. PMID:19504899

  10. Application of martensitic, modified martensitic and duplex stainless steel bar stock for completion equipment

    SciTech Connect

    Bhavsar, R.B.; Montani, R.

    1998-12-31

    Martensitic and duplex stainless steel tubing are commonly used for oil and gas applications containing CO{sub 2}. Completion equipment manufacturing requires use of solid round bar or heavy wall hollows. Material properties for this stock are not identical in all cases. Material properties as well as corrosion characteristics are discussed for 13Cr, 13Cr-5Ni-2Mo and 25Cr alloys. Corrosion testing of modified or Enhanced 13Cr solid bar stock, UNS S41425 and other compositions in H{sub 2}S-Cl{sup {minus}} and pH is reported in coupled and uncoupled condition. Corrosion testing of various super duplex bar stock at various H{sub 2}S-chlorides and temperature in CO{sub 2} environment is reported. Impact value requirements, welding issues and special consideration required for these alloys for completion equipment is discussed. Modified 13Cr and Super Duplex Oil Country Tubular Goods (OCTG) are readily available, however, availability of completion equipment raw material compatible with these OCTG is limited.

  11. Nickel-based alloy/austenitic stainless steel dissimilar weld properties prediction on asymmetric distribution of laser energy

    NASA Astrophysics Data System (ADS)

    Zhou, Siyu; Ma, Guangyi; Chai, Dongsheng; Niu, Fangyong; Dong, Jinfei; Wu, Dongjiang; Zou, Helin

    2016-07-01

    A properties prediction method of Nickel-based alloy (C-276)/austenitic stainless steel (304) dissimilar weld was proposed and validated based on the asymmetric distribution of laser energy. Via the dilution level DC-276 (the ratio of the melted C-276 alloy), the relations between the weld properties and the energy offset ratio EC-276 (the ratio of the irradiated energy on the C-276 alloy) were built, and the effects of EC-276 on the microstructure, mechanical properties and corrosion resistance of dissimilar welds were analyzed. The element distribution Cweld and EC-276 accorded with the lever rule due to the strong convention of the molten pool. Based on the lever rule, it could be predicted that the microstructure mostly consists of γ phase in each weld, the δ-ferrite phase formation was inhibited and the intermetallic phase (P, μ) formation was promoted with the increase of EC-276. The ultimate tensile strength σb of the weld joint could be predicted by the monotonically increasing cubic polynomial model stemming from the strengthening of elements Mo and W. The corrosion potential U, corrosion current density I in the active region and EC-276 also met the cubic polynomial equations, and the corrosion resistance of the dissimilar weld was enhanced with the increasing EC-276, mainly because the element Mo could help form a steady passive film which will resist the Cl- ingress.

  12. Submerged Arc Stainless Steel Strip Cladding—Effect of Post-Weld Heat Treatment on Thermal Fatigue Resistance

    NASA Astrophysics Data System (ADS)

    Kuo, I. C.; Chou, C. P.; Tseng, C. F.; Lee, I. K.

    2009-03-01

    Two types of martensitic stainless steel strips, PFB-132 and PFB-131S, were deposited on SS41 carbon steel substrate by a three-pass submerged arc cladding process. The effects of post-weld heat treatment (PWHT) on thermal fatigue resistance and hardness were evaluated by thermal fatigue and hardness testing, respectively. The weld metal microstructure was investigated by utilizing optical microscopy, scanning electron microscopy (SEM) equipped with energy dispersive X-ray spectroscopy (EDS) and transmission electron microscopy (TEM). Results showed that, by increasing the PWHT temperature, hardness decreased but there was a simultaneous improvement in weldment thermal fatigue resistance. During tempering, carbide, such as (Fe, Cr)23C6, precipitated in the weld metals and molybdenum appeared to promote (Fe, Cr, Mo)23C6 formation. The precipitates of (Fe, Cr, Mo)23C6 revealed a face-centered cubic (FCC) structure with fine grains distributed in the microstructure, thereby effectively increasing thermal fatigue resistance. However, by adding nickel, the AC1 temperature decreased, causing a negative effect on thermal fatigue resistance.

  13. Tunable MoS2 bandgap in MoS2-graphene heterostructures

    NASA Astrophysics Data System (ADS)

    Ebnonnasir, Abbas; Narayanan, Badri; Kodambaka, Suneel; Ciobanu, Cristian V.

    2014-07-01

    Using density functional theory calculations with van der Waals corrections, we investigated how the interlayer orientation affects the structure and electronic properties of MoS2-graphene bilayer heterostructures. Changing the orientation of graphene with respect to MoS2 strongly influences the type and the value of the electronic bandgap in MoS2, while not significantly altering the binding energy between the layers or the interlayer spacing. We show that the physical origin of this tunable bandgap arises from variations in the S-S interplanar distance (MoS2 thickness) with the interlayer orientation, variations which are caused by electron transfer away from the Mo-S bonds.

  14. Prompt {gamma}-ray spectroscopy of the {sup 104}Mo and {sup 108}Mo fission fragments

    SciTech Connect

    Guessous, A.; Schulz, N.; Bentaleb, M.; Lubkiewicz, E.; Durell, J.L.; Pearson, C.J.; Phillips, W.R.; Shannon, J.A.; Urban, W.; Varley, B.J.; Ahmad, I.; Lister, C.J.; Morss, L.R.; Nash, K.L.; Williams, C.W.; Khazrouni, S.

    1996-03-01

    The level structures of the neutron-rich {sup 104}Mo and {sup 108}Mo nuclei have been investigated by observing prompt {gamma} rays emitted in the spontaneous fission of {sup 248}Cm with the EUROGAM spectrometer. Levels with spins up to 12{h_bar} have been observed and {gamma} branching obtained. The data can be satisfactorily described when {sup 104,108}Mo are considered as axially symmetric nuclei: in {sup 104}Mo, rotational bands based on the ground state, the one-phonon and the two-phonon {gamma}-vibrational states and a quasiparticle state have been observed, whereas in {sup 108}Mo the information is limited to the yrast band and the one phonon {gamma} band. {copyright} {ital 1996 The American Physical Society.}

  15. DETECTION OF BACTERIAL BIOFILM ON STAINLESS STEEL BY HYPERSPECTRAL FLUORESCENCE IMAGING

    Technology Transfer Automated Retrieval System (TEKTRAN)

    In this study, hyperspectral fluorescence imaging techniques were investigated for detection of microbial biofilm on stainless steel plates typically used to manufacture food processing equipment. Stainless steel coupons were immersed in bacterium cultures consisting of nonpathogenic E. coli, Pseudo...

  16. ITO-free flexible organic photovoltaics with multilayer MoO3/LiF/MoO3/Ag/MoO3 as the transparent electrode

    NASA Astrophysics Data System (ADS)

    Chen, Shilin; Dai, Yunjie; Zhao, Dewei; Zhang, Hongmei

    2016-05-01

    We present efficient flexible organic photovoltaics (OPVs) with multiple layers of molybdenum oxide (MoO3)/LiF/MoO3/Ag/MoO3 as the transparent electrode, where the thin Ag layer yields high conductivity and the dielectric layer MoO3/LiF/MoO3 has high transparency due to optical interference, leading to improved power conversion efficiency compared with indium tin oxide (ITO) based devices. The MoO3 contacting organic active layer is used as a buffer layer for good hole extraction. Thus, the multilayer MoO3/LiF/MoO3/Ag/MoO3 can improve light transmittance and also facilitate charge carrier extraction. Such an electrode shows excellent mechanical bendability with a 9% reduction of efficiency after 1000 cycles of bending due to the ductile nature of the thin metal layer and dielectric layer used. Our results suggest that the MoO3/LiF/MoO3/Ag/MoO3 multilayer electrode is a promising alternative to ITO as an electrode in OPVs.

  17. Borated stainless steel application in spent-fuel storage racks

    SciTech Connect

    Smith, R.J.; Loomis, G.W.; Deltete, C.P.

    1992-06-01

    EPRI is continuing to investigate the application of borated stainless steel products within the commercial nuclear power industry through participation in code development and material testing. This effort provides documentation of the material properties of interest in design applications utilizing the borated stainless steel products as structural elements as well as serving as neutron absorbers. The properties of most concern in the design of spent fuel storage racks, shipping casks, and other containment type applications are the materials' ductility, tensile strength, corrosion resistance and resistance to degradation due to radiation and temperature. The data presented in this report indicate that practical designs can be achieved utilizing borated stainless steels and that the materials can be cost effectively applied.

  18. Bacterial adhesion on ion-implanted stainless steel surfaces

    NASA Astrophysics Data System (ADS)

    Zhao, Q.; Liu, Y.; Wang, C.; Wang, S.; Peng, N.; Jeynes, C.

    2007-08-01

    Stainless steel disks were implanted with N +, O + and SiF 3+, respectively at the Surrey Ion Beam Centre. The surface properties of the implanted surfaces were analyzed, including surface chemical composition, surface topography, surface roughness and surface free energy. Bacterial adhesion of Pseudomonas aeruginosa, Staphylococcus epidermidis and Staphylococcus aureus, which frequently cause medical device-associated infections was evaluated under static condition and laminar flow condition. The effect of contact time, growth media and surface properties of the ion-implanted steels on bacterial adhesion was investigated. The experimental results showed that SiF 3+-implanted stainless steel performed much better than N +-implanted steel, O +-implanted steel and untreated stainless steel control on reducing bacterial attachment under identical experimental conditions.

  19. Corrosion in lithium-stainless steel thermal-convection systems

    SciTech Connect

    Tortorelli, P.F.; DeVan, J.H.; Selle, J.E.

    1980-01-01

    The corrosion of types 304L and 316 austenitic stainless steel by flowing lithium was studied in thermal-convection loops operated at 500 to 650/sup 0/C. Both weight and compositional changes were measured on specimens distributed throughout each loop and were combined with metallographic examinations to evaluate the corrosion processes. The corrosion rate and mass transfer characteristics did not significantly differ between the two austenitic stainless steels. Addition of 500 or 1700 wt ppM N to purified lithium did not increase the dissolution rate or change the attack mode of type 316 stainless steel. Adding 5 wt % Al to the lithium reduced the weight loss of this steel by a factor of 5 relative to a pure lithium-thermal-convection loop.

  20. Machinability of a Stainless Steel by Electrochemical Discharge Microdrilling

    NASA Astrophysics Data System (ADS)

    Coteaţǎ, Margareta; Schulze, Hans-Peter; Pop, Nicolae; Beşliu, Irina; Slǎtineanu, Laurenţiu

    2011-05-01

    Due to the chemical elements included in their structure for ensuring an increased resistance to the environment action, the stainless steels are characterized by a low machinability when classical machining methods are applied. For this reason, sometimes non-traditional machining methods are applied, one of these being the electrochemical discharge machining. To obtain microholes and to evaluate the machinability by electrochemical discharge microdrilling, test pieces of stainless steel were used for experimental research. The electrolyte was an aqueous solution of sodium silicate with different densities. A complete factorial plan was designed to highlight the influence of some input variables on the sizes of the considered machinability indexes (electrode tool wear, material removal rate, depth of the machined hole). By mathematically processing of experimental data, empirical functions were established both for stainless steel and carbon steel. Graphical representations were used to obtain more suggestive vision concerning the influence exerted by the considered input variables on the size of the machinability indexes.

  1. Machinability of a Stainless Steel by Electrochemical Discharge Microdrilling

    SciTech Connect

    Coteata, Margareta; Pop, Nicolae; Slatineanu, Laurentiu; Schulze, Hans-Peter; Besliu, Irina

    2011-05-04

    Due to the chemical elements included in their structure for ensuring an increased resistance to the environment action, the stainless steels are characterized by a low machinability when classical machining methods are applied. For this reason, sometimes non-traditional machining methods are applied, one of these being the electrochemical discharge machining. To obtain microholes and to evaluate the machinability by electrochemical discharge microdrilling, test pieces of stainless steel were used for experimental research. The electrolyte was an aqueous solution of sodium silicate with different densities. A complete factorial plan was designed to highlight the influence of some input variables on the sizes of the considered machinability indexes (electrode tool wear, material removal rate, depth of the machined hole). By mathematically processing of experimental data, empirical functions were established both for stainless steel and carbon steel. Graphical representations were used to obtain more suggestive vision concerning the influence exerted by the considered input variables on the size of the machinability indexes.

  2. Highly robust stainless steel tips as microelectrospray emitters.

    PubMed

    Ishihama, Yasushi; Katayama, Hiroyuki; Asakawa, Naoki; Oda, Yoshiya

    2002-01-01

    Tapered stainless steel spray tips for sheathless microelectrospray ionization (microESI) have been developed. The fabrication procedure for the tapered stainless steel tips was optimized using an electropolishing technique followed by removal of the burr. Using the tip as the microESI emitter, a stable ESI spray was obtained at a flow rate of 20 nL/min. The sensitivity of the microESI system was almost two orders greater than that of the conventional ion spray system. The tip was highly stable, and was successfully used for over 1000 h. Moreover, these stainless steel tips were suitable for use with sheathless capillary electrophoresis/mass spectrometry (CE/MS) and capillary liquid chromatography/mass spectrometry (LC/MS) for routine analysis in proteomic and pharmaceutical applications. PMID:11968120

  3. Keplerate cluster (Mo-132) mediated electrostatic assembly of nanoparticles.

    PubMed

    Gooch, Jonathan; Jalan, Abhishek A; Jones, Stephanie; Hine, Corey R; Alam, Rabeka; Garai, Somenath; Maye, Mathew M; Müller, Achim; Zubieta, Jon

    2014-10-15

    The electrostatic assembly between a series of differently charged Mo-132-type Keplerates present in the compounds (NH4)42[{(Mo(VI))Mo(VI)5O21(H2O)6}12 {Mo(V)2O4(CH3COO)}30].ca. {300 H2O+10 CH3COONH4} (Mo-132a), (NH4)72-n[{(H2O)81-n+(NH4)n} {(Mo(VI))Mo(VI)5O21(H2O)6}12 {Mo(V)2O4(SO4)}30].ca. 200 H2O (Mo-132b), and Na10(NH4)62[{(Mo(VI))Mo(VI)5O21(H2O)6}12 {Mo(V)2O4(HPO4)}30]. ca. {300H2O+2Na(+)+2NH4(+)+4H2PO4(-)} (Mo-132c) with cationic gold nanoparticles (AuNPs) was investigated for the first time. The rapid electrostatic assembly from nanoscopic entities to micron scale aggregates was observed upon precipitation, which closely matched the point of aggregate electroneutrality. Successful assembly was demonstrated using UV-vis, DLS, TEM, and zeta-potential analysis. Results indicate that the point at which precipitation occurs is related to charge balance or electroneutrality, and that counterions at both the Mo-132 and AuNP play a significant role in assembly. PMID:25086388

  4. The Tribological Difference between Biomedical Steels and CoCrMo-Alloys

    PubMed Central

    Fischer, Alfons; Weiß, Sabine; Wimmer, Markus A.

    2012-01-01

    In orthopedic surgery different self-mating metal couples are used for sliding wear applications. Despite the fact that in mechanical engineering self-mating austenitic alloys often lead to adhesion and seizure in biomedical engineering the different grades of Co-base alloys show good clinical results e.g. as hip joints. The reason stems from the fact that they generate a so-called tribomaterial during articulation, which consists of a mixture of nanometer small metallic grains and organic substances from the interfacial medium, which act as boundary lubricant. Even though stainless steels also generate such a tribomaterial they were ruled out from the beginning already in the 1950 as “inappropriate”. On the basis of materials with a clinical track record this contribution shows that the cyclic creep characteristics within the shear zone underneath the tribomaterial are another important criterion for a sufficient wear behavior. By means of sliding wear and torsional fatigue tests followed by electron microscopy it is shown, that austenitic materials generate wear particles of either nano- or of microsize. The latter are produced by crack initiation and propagation within the shear fatigue zone which is related to the formation of subsurface dislocation cells and, therefore, by the fact that a Ni-containing CrNiMo solid solution allows for wavy-slip. In contrast to this a Ni-free CrMnMo solid solution with further additions of C and N only shows planar slip. This leads to the formation of nanosize wear particles and distinctly improves the wear behavior. Still the latter does not fully achieve that of CoCrMo, which also shows solely planar-slip behavior. This explains why for metallurgical reasons the Ni-containing 316L-type of steels had to fail in such boundary lubricated sliding wear tribosystems. PMID:22498283

  5. The tribological difference between biomedical steels and CoCrMo-alloys.

    PubMed

    Fischer, Alfons; Weiss, Sabine; Wimmer, Markus A

    2012-05-01

    In orthopedic surgery, different self-mating metal couples are used for sliding wear applications. Despite the fact that in mechanical engineering, self-mating austenitic alloys often lead to adhesion and seizure in biomedical engineering, the different grades of Co-base alloys show good clinical results, e.g., as hip joints. The reason stems from the fact that they generate a so-called tribomaterial during articulation, which consists of a mixture of nanometer small metallic grains and organic substances from the interfacial medium, which act as a boundary lubricant. Even though stainless steel also generate such a tribomaterial, they were ruled out from the beginning already in the 1950s as "inappropriate". On the basis of materials with a clinical track record, this contribution shows that the cyclic creep characteristics within the shear zone underneath the tribomaterial are another important criterion for a sufficient wear behavior. By means of sliding wear and torsional fatigue tests followed by electron microscopy, it is shown that austenitic materials generate wear particles of either nano- or of microsize. The latter are produced by crack initiation and propagation within the shear fatigue zone which is related to the formation of subsurface dislocation cells and, therefore, by the fact that an Ni-containing CrNiMo solid solution allows for wavy-slip. In contrast to this, an Ni-free CrMnMo solid solution with further additions of C and N only shows planar slip. This leads to the formation of nanosize wear particles and distinctly improves the wear behavior. Still, the latter does not fully achieve that of CoCrMo, which also shows a solely planar-slip behavior. This explains why for metallurgical reasons the Ni-containing 316L-type of steels had to fail in such boundary lubricated sliding wear tribosystems. PMID:22498283

  6. Microstructure and texture of Nb + Ti stabilized ferritic stainless steel

    SciTech Connect

    Yan Haitao Bi Hongyun; Li Xin; Xu Zhou

    2008-12-15

    The microstructure, texture and grain boundary character distribution of Nb + Ti stabilized ferritic stainless steel were analyzed using scanning electron microscopy, transmission electron microscopy and X-ray diffraction. The addition of alloying elements such as Ti and Nb to ferritic stainless steel causes the formation of TiN, NbC and Fe{sub 2}Nb. The textures of cold rolled samples were dominated by the {alpha}-fiber, while the textures of annealed samples exhibit a very strong {gamma}-fiber. The changes in texture are closely related to the grain boundary characteristics.

  7. Transmission electron microscopy of undermined passive films on stainless steel

    SciTech Connect

    Isaacs, H.S.; Zhu, Y.; Sabatini, R.L.; Ryan, M.P.

    1999-06-01

    A study has been made of the passive film remaining over pits on stainless steel using a high resolution transmission electron microscope. Type 305 stainless steel was passivated in a borate buffer solution and pitted in ferric chloride. Passive films formed at 0.2 V relative to a saturated calomel electrode were found to be amorphous. Films formed at higher potentials showed only broad diffraction rings. The passive film was found to cover a remnant lacy structure formed over pits passivated at 0.8 V. The metallic strands of the lace were roughly hemitubular in shape with the curved surface facing the center of the pit.

  8. Corrosion evaluation of stainless steel root weld shielding

    SciTech Connect

    Gorog, M.; Sawyer, L.A.

    1999-07-01

    The effect of five shielding methods for gas tungsten arc root pass welds, on the corrosion resistance of stainless steel was evaluated in two laboratory solutions. The first experiment was performed in 6% ferric chloride solution, a test designed to corrode stainless steel. The second experiment was performed in a simulated paper machine white water solution that contained hydrogen peroxide. Argon shielding produced excellent results by maintaining corrosion resistance in both solutions. Nitrogen purging and flux coated TIG rod techniques produced variable results. Paste fluxes and welding without shielding are not recommended for root protection. They performed very poorly with the welds corroding in both tests.

  9. Comparison of carbon fiber and stainless steel root canal posts.

    PubMed

    Purton, D G; Payne, J A

    1996-02-01

    This in vitro study compared physical properties of root canal posts made of carbon fiber-reinforced epoxy resin with those of stainless steel posts. Three-point bending tests were used to derive the transverse modulus of elasticity of the posts. Resin composite cores on the posts were subjected to tensile forces to test the bonds between the cores and posts. Carbon fiber posts appeared to have adequate rigidity for their designed purpose. The bond strength of the resin composite cores to the carbon fiber posts was significantly less than that to the stainless steel posts. PMID:9063218

  10. From flint to stainless steel: observations on surgical instrument composition.

    PubMed Central

    Kirkup, J.

    1993-01-01

    Man's failure to extract deeply embedded thorns and arrowheads, with bare hands and teeth, stimulated 'instrument substitutes' mimicking these appendages. Evidence from primitive communities suggest animal, plant and mineral items were employed, both before and after metal became the standard material of today's armamentarium. Changing surgical instrument composition has mirrored concurrent technology and manufacturing methods both of which are reviewed. Particular significance is accorded flint, bronze, crucible steel, thermal sterilisation, nickel-plate, stainless steel and disposable plastics. The paper is based on an exhibition From Flint to Stainless Steel on display at the College. Images Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 PMID:8215156

  11. Corrosion induced by cathodic hydrogen in 2205 duplex stainless steel

    NASA Astrophysics Data System (ADS)

    Michalska, J.

    2011-05-01

    In this work new results about the influence of cathodic hydrogen on passivity and corrosion resistance of 2205 duplex stainless steel are described. The results were discussed by taking into account hydrogen charged samples and without hydrogen. The corrosion resistance to pitting was qualified with the polarization curves. The conclusion is that, hydrogen deteriorated the passive film stability and corrosion resistance to pitting of 2205 duplex stainless steel. The presence of hydrogen in passive films increases corrosion current density and decreases the potential of the film breakdown. It was also found that degree of susceptibility to hydrogen action was dependent on the hydrogen charging conditions.

  12. Ozone decay on stainless steel and sugarcane bagasse surfaces

    NASA Astrophysics Data System (ADS)

    Souza-Corrêa, Jorge A.; Oliveira, Carlos; Amorim, Jayr

    2013-07-01

    Ozone was generated using dielectric barrier discharges at atmospheric pressure to treat sugarcane bagasse for bioethanol production. It was shown that interaction of ozone molecules with the pretreatment reactor wall (stainless steel) needs to be considered during bagasse oxidation in order to evaluate the pretreatment efficiency. The decomposition coefficients for ozone on both materials were determined to be (3.3 ± 0.2) × 10-8 for stainless steel and (2.0 ± 0.3) × 10-7 for bagasse. The results have indicated that ozone decomposition has occurred more efficiently on the biomass material.

  13. Characterizing pre-polished Type 304L stainless steel

    SciTech Connect

    Hsu, R.H.; Summer, M.E.; Rankin, W.N.

    1994-10-01

    Prepolished Type 304L stainless steel surfaces are being specified for replacement of some equipment in the 221-H Canyon Building at the Savannah River Site. A prepolished stainless steel surface picks up less contamination than a hot-rolled and pickled surface and is easier to decontaminate; therefore, less waste is generated. Surface-characterization techniques and specification for a prepolished surface were developed to ensure that prepolished items being obtained were properly electropolished. The use of this technology has resulted in obtaining prepolished items with an improved surface finish.

  14. Advanced Cast Austenitic Stainless Steels for High Temperature Components

    SciTech Connect

    Maziasz, P.J.; Shingledecker, J.P.; Evans, N.D.; Pollard, M.J.

    2008-10-09

    In July of 2002, a Cooperative Research and Development Agreement (CRADA) was undertaken between Oak Ridge National Laboratory (ORNL) and Caterpillar, Inc. (Caterpillar Technical Center) to develop and commercialize new cast stainless steels invented and initially tested on a prior CRADA. This CRADA is a direct follow-on project to CRADA ORNL-99-0533 for diesel engine exhaust component and gas turbine engine structural component applications. The goal of this new CRADA was to develop and commercialize the newly discovered cast stainless steels (primarily CF8C-Plus) with improved performance and reliability, as lower-cost upgrade alternatives to more costly cast Ni-based superalloys.

  15. Susceptibility of stainless steel weldments to microbiologically influenced corrosion

    SciTech Connect

    Borenstein, S.W.

    1993-12-31

    Microbiologically influenced corrosion (MIC) is the term used for the phenomenon where corrosion is initiated or accelerated by microorganisms. Biofilms of bacteria form on metal surfaces when exposed to natural waters. The activity of these biofilms and how they attach themselves to metal surfaces directly influence corrosion mechanisms. This paper describes the mechanisms for MIC and the factors which influence the susceptibility of austenitic stainless steel weldments to MIC. The metallurgical, microbiological and electrochemical factors that influence MIC are discussed. Case histories of MIC-related failures and field test results of austenitic stainless steel weldments in various welded conditions are presented.

  16. 49 CFR 178.47 - Specification 4DS welded stainless steel cylinders for aircraft use.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Specification 4DS welded stainless steel cylinders...) SPECIFICATIONS FOR PACKAGINGS Specifications for Cylinders § 178.47 Specification 4DS welded stainless steel... stainless steel sphere (two seamless hemispheres) or circumferentially welded cylinder both with a...

  17. 49 CFR 178.47 - Specification 4DS welded stainless steel cylinders for aircraft use.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Specification 4DS welded stainless steel cylinders...) SPECIFICATIONS FOR PACKAGINGS Specifications for Cylinders § 178.47 Specification 4DS welded stainless steel... stainless steel sphere (two seamless hemispheres) or circumferentially welded cylinder both with a...

  18. 77 FR 60478 - Control of Ferrite Content in Stainless Steel Weld Metal

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-10-03

    ... COMMISSION Control of Ferrite Content in Stainless Steel Weld Metal AGENCY: Nuclear Regulatory Commission... Ferrite Content in Stainless Steel Weld Metal.'' This guide describes a method that the NRC staff considers acceptable for controlling ferrite content in stainless steel weld metal. Revision 4 updates...

  19. 76 FR 31585 - Forged Stainless Steel Flanges From India: Notice of Rescission of Antidumping Duty...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-01

    ... International Trade Administration Forged Stainless Steel Flanges From India: Notice of Rescission of... stainless steel flanges from India. The period of review is February 1, 2010, through January 22, 2011... stainless steel flanges from India. See Antidumping or Countervailing Duty Order, Finding, or...

  20. 76 FR 1599 - Stainless Steel Bar From Brazil: Final Results of Antidumping Duty Administrative Review

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-01-11

    ... Less Than Fair Value: Stainless Steel Bar From Brazil, 59 FR 66914 (December 28, 1994). These deposit... International Trade Administration Stainless Steel Bar From Brazil: Final Results of Antidumping Duty... results of its administrative review of the antidumping duty order on stainless steel bar from Brazil....

  1. 77 FR 60673 - Drawn Stainless Steel Sinks From the People's Republic of China: Antidumping Duty Investigation

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-10-04

    ... International Trade Administration Drawn Stainless Steel Sinks From the People's Republic of China: Antidumping...'') preliminarily determines that drawn stainless steel sinks (``drawn sinks'') from the People's Republic of China... unfinished, regardless of type of finish, gauge, or grade of stainless steel. Mounting clips,...

  2. 75 FR 67689 - Stainless Steel Bar From Brazil: Preliminary Results of Antidumping Duty Administrative Review

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-03

    ... Brazil. See Antidumping Duty Orders: Stainless Steel Bar from Brazil, India and Japan, 60 FR 9661... Less Than Fair Value: Stainless Steel Bar From Brazil, 59 FR 66914 (December 28, 1994). These deposit... International Trade Administration Stainless Steel Bar From Brazil: Preliminary Results of Antidumping...

  3. 77 FR 13270 - Stainless Steel Bar From India: Preliminary Results and Partial Rescission of the Antidumping...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-06

    ... Duty Orders: Stainless Steel Bar from Brazil, India and Japan, 60 FR 9661 (February 21, 1995) (the... Less Than Fair Value: Stainless Steel Bar from India, 59 FR 66915 (December 28, 1994). These deposit... International Trade Administration Stainless Steel Bar From India: Preliminary Results and Partial Rescission...

  4. 75 FR 12514 - Stainless Steel Bar From Brazil: Preliminary Results of Antidumping Duty Administrative Review

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-03-16

    ... Brazil. See Antidumping Duty Orders: Stainless Steel Bar from Brazil, India and Japan, 60 FR 9661... Review, 73 FR 75398, 75399 (December 11, 2008) (SSPC from Belgium), and Stainless Steel Sheet and Strip... International Trade Administration Stainless Steel Bar From Brazil: Preliminary Results of Antidumping...

  5. Nuclear structure of {sup 102}Mo

    SciTech Connect

    Rahman, M.A.; Chowdhury, M.S.

    2006-05-15

    Nuclear structure of the {sup 102}Mo nucleus has been studied using the {sup 100}Mo(t,p){sup 102}Mo reaction with the triton beam energy of 12 MeV obtained from the tandem Van de Graaff accelerator and a multichannel magnetic spectrograph. Proton spectra are obtained at 12 different angles from 5 deg. to 87.5 deg., at an interval of 7.5 deg. and are detected in nuclear emulsion plates. Thirty-five levels in the energy range from 0.000 to 3.248 MeV have been observed. The results yield a number of new levels with spin assignments. Absolute differential cross sections for the levels have been measured. The experimental angular distributions are compared with the theoretical distorted-wave Born approximation calculations to determine L and J{sup {pi}} values. The present results are compared with the previous results.

  6. Wetting of metals and glasses on Mo

    SciTech Connect

    Saiz, Eduardo; Tomsia, Antoni P.; Saiz, Eduardo; Lopez-Esteban, Sonia; Benhassine, Mehdi; de Coninck, Joel; Rauch, Nicole; Ruehle, Manfred

    2008-01-08

    The wetting of low melting point metals and Si-Ca-Al-Ti-O glasses on molybdenum has been investigated. The selected metals (Au, Cu, Ag) form a simple eutectic with Mo. Metal spreading occurs under nonreactive conditions without interdiffusion or ridge formation. The metals exhibit low (non-zero) contact angles on Mo but this requires temperatures higher than 1100 C in reducing atmospheres in order to eliminate a layer of adsorbed impurities on the molybdenum surface. By controlling the oxygen activity in the furnace, glass spreading can take place under reactive or nonreactive conditions. We have found that in the glass/Mo system the contact angle does not decrease under reactive conditions. In all cases, adsorption from the liquid seems to accelerate the diffusivity on the free molybdenum surface.

  7. Elevated Temperature Tensile Tests on DU–10Mo Rolled Foils

    SciTech Connect

    Schulthess, Jason

    2014-09-01

    Tensile mechanical properties for uranium-10 wt.% molybdenum (U–10Mo) foils are required to support modeling and qualification of new monolithic fuel plate designs. It is expected that depleted uranium-10 wt% Mo (DU–10Mo) mechanical behavior is representative of the low enriched U–10Mo to be used in the actual fuel plates, therefore DU-10Mo was studied to simplify material processing, handling, and testing requirements. In this report, tensile testing of DU-10Mo fuel foils prepared using four different thermomechanical processing treatments were conducted to assess the impact of foil fabrication history on resultant tensile properties.

  8. Mechanically alloyed Mo-Si-B alloys with a continuous a-Mo matrix and improved mechanical properties

    SciTech Connect

    Krueger, M.; Franz, S.; Heilmaier, M.; Schneibel, Joachim H; Jehanno, P.; Boening, Mike Boening; Kestler, Heinrich

    2008-01-01

    Mechanical alloying (MA) followed by cold isostatic pressing (CIPing), sintering and hot isostatic pressing (HIPing) was used to prepare Mo-base silicide alloys consisting of a Mo(Si) solid solution and the intermetallic phases Mo{sub 3}Si and Mo{sub 5}SiB{sub 2}. The microstructural development during milling of both binary Mo-Si and Mo-B and ternary Mo-Si-B powder mixtures was evaluated. While obtaining a supersaturated solid solution requires rather long milling times, domain size (which correlates with the grain size) is reduced to below 100 {angstrom} after about 10 h of milling. After heat treatment and consolidation the microstructure reveals a continuous {alpha}-Mo matrix with embedded, uniformly distributed intermetallic particles. The establishment of such a microstructure is beneficial for the mechanical properties since, as compared to a discontinuous {alpha}-Mo matrix, it decreases the brittle-to-ductile transition temperature (BDTT) by about 150 K.

  9. Phase stability of U-Mo-Ti alloys and interdiffusion behaviors of U-Mo-Ti/Al-Si

    SciTech Connect

    Park, Jong Man; Ryu, Ho Jin; Park, Jae Soon; Oh, Seok Jin; Kim, Chang Kyu; Kim, Yeon Soo; Hofman, Gerard L.

    2008-07-15

    As a remedy for reducing reaction between U-Mo and Al in U-Mo/Al dispersion fuel, adding an alloying element such as Zr and Ti in U-Mo has been proposed at ANL. Although ANL's work showed the potential effectiveness of these elements based on thermodynamic and metallurgical analyses, the effect of a Ti addition in U-Mo remains unproven. The out-of-pile tests of U-Mo-Ti alloys, which focused on phase stability and interdiffusion behavior against Al, are meaningful to predict their efficacy during an irradiation. At the 2006 RERTR conference, we presented our work on the interdiffusion behaviors of U-Mo-Zr/Al-Si. In this paper, we will present the results for substituting U-Mo-Zr with U-Mo-Ti. Unlike U-Mo-Zr alloys, the gamma-heat-treated U-7Mo-xTi (x=1{approx}3 wt%) exhibited a metastable {gamma}-U phase, regardless of the Ti content. In these samples, however, a small amount of second-phase precipitates with a high Ti concentration was observed. The gamma phase stability of the U-Mo-Ti alloys at 500 deg C was similar to that of the U-Mo-Zr alloys. Interdiffusion test results between U-Mo-Ti alloys and Al-Si alloys will also be presented and a comparison with the previous results with U- Mo-Zr/Al-Si will also be included. (author)

  10. Oxidation, Reduction, and Condensation of Alcohols over (MO3)3 (M=Mo, W) Nanoclusters

    SciTech Connect

    Fang, Zongtang; Li, Zhenjun; Kelley, Matthew S.; Kay, Bruce D.; Li, Shenggang; Hennigan, Jamie M.; Rousseau, Roger J.; Dohnalek, Zdenek; Dixon, David A.

    2014-10-02

    The reactions of deuterated methanol, ethanol, 1-propanol, 1-butanol, 2-propanol, 2-butanol and t-butanol over cyclic (MO3)3 (M = Mo, W) clusters were studied experimentally with temperature programmed desorption (TPD) and theoretically with coupled cluster CCSD(T) theory and density functional theory. The reactions of two alcohols per M3O9 cluster are required to provide agreement with experiment for D2O release, dehydrogenation and dehydration. The reaction begins with the elimination of water by proton transfers and forms an intermediate dialkoxy species which can undergo further reaction. Dehydration proceeds by a β hydrogen transfer to a terminal M=O. Dehydrogenation takes place via an α hydrogen transfer to an adjacent MoVI = O atom or a WVI metal center with redox involved for M = Mo and no redox for M = W. The two channels have comparable activation energies. H/D exchange to produce alcohols can take place after olefin is released or via the dialkoxy species depending on the alcohol and the cluster. The Lewis acidity of the metal center with WVI being larger than MoVI results in the increased reactivity of W3O9 over Mo3O9 for dehydrogenation and dehydration.

  11. Mo-Type Superlattices in Hastelloy C-2000 Superalloy with Low Mo/Cr Ratio

    NASA Astrophysics Data System (ADS)

    Yuan, Liang; Hu, Rui; Zhang, Tiebang; Han, Yinben; Xue, Xiangyi; Li, Jinshan

    2014-09-01

    This paper focuses on the precipitation behavior of superlattices phases in new Hastelloy C-2000 alloy with low Mo/Cr ratio owing to their detrimental effects on both mechanical and corrosion-resistance properties of the alloys. The precipitation behavior of superlattices phases in the C-2000 alloy was investigated at 600 °C in the aging time range of 100-500 h. The results revealed that Pt2Mo-type superlattices phases have been precipitated after aging at 600 °C for 100 h. Typically, the Pt2Mo-type precipitated phases meet to a stoichiometric ratio of Ni2(Cr, Mo) in this alloy. As increasing aging time from 100 to 500 h, size of the phase increases from around 13 to 55 nm. Besides, morphology of the Ni2(Cr, Mo) precipitated phases changes from a lean to a fat ellipse with increasing aging time due to the effect of the Mo/Cr atomic ratio and alloying elements on transformation paths from disorder to order. In addition, solution temperature of the Pt2Mo-type superlattices is around 725 °C determined by differential scanning calorimetry method, which was significantly dependent on the heating rate.

  12. The modulation of Schottky barriers of metal-MoS2 contacts via BN-MoS2 heterostructures.

    PubMed

    Su, Jie; Feng, Liping; Zhang, Yan; Liu, Zhengtang

    2016-06-22

    Using first-principles calculations within density functional theory, we systematically studied the effect of BN-MoS2 heterostructure on the Schottky barriers of metal-MoS2 contacts. Two types of FETs are designed according to the area of the BN-MoS2 heterostructure. Results show that the vertical and lateral Schottky barriers in all the studied contacts, irrespective of the work function of the metal, are significantly reduced or even vanish when the BN-MoS2 heterostructure substitutes the monolayer MoS2. Only the n-type lateral Schottky barrier of Au/BN-MoS2 contact relates to the area of the BN-MoS2 heterostructure. Notably, the Pt-MoS2 contact with n-type character is transformed into a p-type contact upon substituting the monolayer MoS2 by a BN-MoS2 heterostructure. These changes of the contact natures are ascribed to the variation of Fermi level pinning, work function and charge distribution. Analysis demonstrates that the Fermi level pinning effects are significantly weakened for metal/BN-MoS2 contacts because no gap states dominated by MoS2 are formed, in contrast to those of metal-MoS2 contacts. Although additional BN layers reduce the interlayer interaction and the work function of the metal, the Schottky barriers of metal/BN-MoS2 contacts still do not obey the Schottky-Mott rule. Moreover, different from metal-MoS2 contacts, the charges transfer from electrodes to the monolayer MoS2, resulting in an increment of the work function of these metals in metal/BN-MoS2 contacts. These findings may prove to be instrumental in the future design of new MoS2-based FETs with ohmic contact or p-type character. PMID:27282959

  13. Purification and characterization of a FeMo cofactor-deficient MoFe protein.

    PubMed

    Gavini, N; Ma, L; Watt, G; Burgess, B K

    1994-10-01

    Previous studies have shown that the nifH gene product is required for FeMo cofactor biosynthesis and insertion and that a delta nifH strain of Azotobacter vinelandii designated DJ54 accumulates a FeMo cofactor-deficient MoFe protein that is distinct from the FeMo cofactor-deficient protein synthesis by Nif B-, N-, or E- strains [Tal, S., Chun, T., Gavini, N., & Burgess, B. K. (1991) J. Biol. Chem. 266, 10654-10657]. Here we report the purification and activation of the MoFe protein from DJ54. The purified protein is an alpha 2 beta 2 tetramer that is indistinguishable from the wild-type MoFe protein by the criteria of SDS-polyacrylamide gel electrophoresis, native gel electrophoresis, and two-dimensional gel electrophoresis. It binds normally to its redox partner, the Fe protein, by the criterion of chemical cross-linking. It does not contain FeMo cofactor and does not catalyze significant C2H2 reduction or reduction-independent MgATP hydrolysis. It can, however, be activated with FeMo cofactor following the addition of the Fe protein and MgATP when an additional required component(s) is supplied by cell-free extracts from a delta nifD strain of A. vinelandii. The purified DJ54 MoFe protein does contain P-clusters by the criteria of metal analysis, CD spectroscopy, cluster extrusion, and electrochemical reduction of the POX state. In the presence of dithionite it exhibits an axial S = 1/2 EPR signal that integrates to 0.1-0.3 spin per alpha 2 beta 2 tetramer.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:7918402

  14. Synthesis, structural elucidation, and catalytic properties in olefin epoxidation of the polymeric hybrid material [Mo3O9(2-[3(5)-pyrazolyl]pyridine)]n.

    PubMed

    Amarante, Tatiana R; Neves, Patrícia; Gomes, Ana C; Nolasco, Mariela M; Ribeiro-Claro, Paulo; Coelho, Ana C; Valente, Anabela A; Paz, Filipe A Almeida; Smeets, Stef; McCusker, Lynne B; Pillinger, Martyn; Gonçalves, Isabel S

    2014-03-01

    The reaction of [MoO2Cl2(pzpy)] (1) (pzpy = 2-[3(5)-pyrazolyl]pyridine) with water in an open reflux system (16 h), in a microwave synthesis system (120 °C, 2 h), or in a Teflon-lined stainless steel digestion bomb (100 °C, 19 h) gave the molybdenum oxide/pyrazolylpyridine polymeric hybrid material [Mo3O9(pzpy)]n (2) as a microcrystalline powder in yields of 72–79%. Compound 2 can also be obtained by the hydrothermal reaction of MoO3, pzpy, and H2O at 160 °C for 3 d. Secondary products isolated from the reaction solutions included the salt (pzpyH)2(MoCl4) (3) (pzpyH = 2-[3(5)-pyrazolyl]pyridinium), containing a very rare example of the tetrahedral MoCl4(2–) anion, and the tetranuclear compound [Mo4O12(pzpy)4] (4). Reaction of 2 with excess tert-butylhydroperoxide (TBHP) led to the isolation of the oxodiperoxo complex [MoO(O2)2(pzpy)] (5). Single-crystal X-ray structures of 3 and 5 are described. Fourier transform (FT)-IR and FT Raman spectra for 1, 4, and 5 were assigned based on density functional theory calculations. The structure of 2 was determined from synchrotron powder X-ray diffraction data in combination with other physicochemical information. In 2, a hybrid organic–inorganic one-dimensional (1D) polymer, ∞(1)[Mo3O9(pzpy)], is formed by the connection of two very distinct components: a double ladder-type inorganic core reminiscent of the crystal structure of MoO3 and 1D chains of corner-sharing distorted {MoO4N2} octahedra. Compound 2 exhibits moderate activity and high selectivity when used as a (pre)catalyst for the epoxidation of cis-cyclooctene with TBHP. Under the reaction conditions used, 2 is poorly soluble and is gradually converted into 5, which is at least partly responsible for the catalytic reaction. PMID:24520803

  15. Elastic modulus of phases in Ti–Mo alloys

    SciTech Connect

    Zhang, Wei-dong; Liu, Yong; Wu, Hong; Song, Min; Zhang, Tuo-yang; Lan, Xiao-dong; Yao, Tian-hang

    2015-08-15

    In this work, a series of binary Ti–Mo alloys with the Mo contents ranging from 3.2 to 12 at.% were prepared using non-consumable arc melting. The microstructures were investigated by X-ray diffraction and transmission electron microscope, and the elastic modulus was evaluated by nanoindentation testing technique. The evolution of the volume fractions of ω phase was investigated using X-ray photoelectron spectroscopy. The results indicated that the phase constitution and elastic modulus of the Ti–Mo alloys are sensitive to the Mo content. Ti–3.2Mo and Ti–8Mo alloys containing only α and β phases, respectively, have a low elastic modulus. In contrast, Ti–4.5Mo, Ti–6Mo, Ti–7Mo alloys, with different contents of ω phase, have a high elastic modulus. A simple micromechanical model was used to calculate the elastic modulus of ω phase (E{sub ω}), which was determined to be 174.354 GPa. - Highlights: • Ti–Mo alloys with the Mo contents ranging from 3.2 to 12 at.% were investigated. • XPS was used to investigate the volume fractions of ω phase. • The elastic modulus of Ti–Mo alloys is sensitive to the Mo content. • The elastic modulus of ω phase was determined to be 174.354 GPa.

  16. Effect of MoO3 constituents on the growth of MoS2 nanosheets by chemical vapor deposition

    NASA Astrophysics Data System (ADS)

    Wang, Xuan; Zhang, Yong Ping; Qian Chen, Zhi

    2016-06-01

    The highly crystalline and uniform MoS2 film was grown on Si substrate by a low-pressure chemical vapor deposition method using S and MoO3 as precursors at an elevated temperature. The structures and properties of MoS2 nanosheets vary greatly with the content of MoO3 constituents in the films. The nanostructured MoS2 film exhibits strong photoluminescence in the visible range. This work may provide a pathway to synthesizing MoS2 nanosheets and facilitate the development of applicable devices.

  17. Wafer-scale MoS2 thin layers prepared by MoO3 sulfurization

    NASA Astrophysics Data System (ADS)

    Lin, Yu-Chuan; Zhang, Wenjing; Huang, Jing-Kai; Liu, Keng-Ku; Lee, Yi-Hsien; Liang, Chi-Te; Chu, Chih-Wei; Li, Lain-Jong

    2012-09-01

    Atomically thin molybdenum disulfide (MoS2) layers have attracted great interest due to their direct-gap property and potential applications in optoelectronics and energy harvesting. Meanwhile, they are extremely bendable, promising for applications in flexible electronics. However, the synthetic approach to obtain large-area MoS2 atomic thin layers is still lacking. Here we report that wafer-scale MoS2 thin layers can be obtained using MoO3 thin films as a starting material followed by a two-step thermal process, reduction of MoO3 at 500 °C in hydrogen and sulfurization at 1000 °C in the presence of sulfur. Spectroscopic, optical and electrical characterizations reveal that these films are polycrystalline and with semiconductor properties. The obtained MoS2 films are uniform in thickness and easily transferable to arbitrary substrates, which make such films suitable for flexible electronics or optoelectronics.Atomically thin molybdenum disulfide (MoS2) layers have attracted great interest due to their direct-gap property and potential applications in optoelectronics and energy harvesting. Meanwhile, they are extremely bendable, promising for applications in flexible electronics. However, the synthetic approach to obtain large-area MoS2 atomic thin layers is still lacking. Here we report that wafer-scale MoS2 thin layers can be obtained using MoO3 thin films as a starting material followed by a two-step thermal process, reduction of MoO3 at 500 °C in hydrogen and sulfurization at 1000 °C in the presence of sulfur. Spectroscopic, optical and electrical characterizations reveal that these films are polycrystalline and with semiconductor properties. The obtained MoS2 films are uniform in thickness and easily transferable to arbitrary substrates, which make such films suitable for flexible electronics or optoelectronics. Electronic supplementary information (ESI) available. See DOI: 10.1039/c2nr31833d

  18. Electrochemically induced annealing of stainless-steel surfaces.

    PubMed

    Burstein, G T; Hutchings, I M; Sasaki, K

    2000-10-19

    Modification of the surface properties of metals without affecting their bulk properties is of technological interest in demanding applications where surface stability and hardness are important. When austenitic stainless steel is heavily plastically deformed by grinding or rolling, a martensitic phase transformation occurs that causes significant changes in the bulk and surface mechanical properties of the alloy. This martensitic phase can also be generated in stainless-steel surfaces by cathodic charging, as a consequence of lattice strain generated by absorbed hydrogen. Heat treatment of the steel to temperatures of several hundred degrees can result in loss of the martensitic structure, but this alters the bulk properties of the alloy. Here we show that martensitic structures in stainless steel can be removed by appropriate electrochemical treatment in aqueous solutions at much lower temperature than conventional annealing treatments. This electrochemically induced annealing process allows the hardness of cold-worked stainless steels to be maintained, while eliminating the brittle martensitic phase from the surface. Using this approach, we are able to anneal the surface and near-surface regions of specimens that contain rolling-induced martensite throughout their bulk, as well as those containing surface martensite induced by grinding. Although the origin of the electrochemical annealing process still needs further clarification, we expect that this treatment will lead to further development in enhancing the surface properties of metals. PMID:11057662

  19. 77 FR 1504 - Stainless Steel Wire Rod From India

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-01-10

    ... Commission instituted this review on July 1, 2011 (76 FR 38686) and determined on October 4, 2011, that it would conduct an expedited review (76 FR 64105, October 17, 2011). The Commission transmitted its... COMMISSION Stainless Steel Wire Rod From India Determination On the basis of the record \\1\\ developed in...

  20. Gas Leak from Vinyl Taped Stainless Steel Dressing Jars

    SciTech Connect

    Tim Hayes

    1999-03-01

    The leak rates of nitrogen gas from stainless steel dressing jars taped with 2 inch vinyl tape were measured. These results were used to calculate hydrogen leak rates from the same jars. The calculations show that the maximum concentration of hydrogen buildup in this type of container configuration will beat least 3 orders of magnitude below the lower explosion limit for hydrogen in air.

  1. Battery and fuel cell electrodes containing stainless steel charging additive

    DOEpatents

    Zuckerbrod, David; Gibney, Ann

    1984-01-01

    An electrode for use in electrochemical energy cells is made, comprising a hydrophilic layer and a hydrophobic layer, where the hydrophilic layer comprises a hydrophilic composite which includes: (i) carbon particles; (ii) stainless steel particles; (iii) a nonwetting agent; and (iv) a catalyst, where at least one current collector contacts said composite.

  2. Stainless steel 301 and Inconel 718 hydrogen embrittlement

    NASA Technical Reports Server (NTRS)

    Allgeier, R. K.; Forman, R.

    1970-01-01

    Conditions and results of tensile tests of 26 Inconel 718 and four cryoformed stainless steel specimens are presented. Conclusions determine maximum safe hydrogen operating pressure for cryogenic pressure vessels and provide definitive information concerning flaw growth characteristics under the most severe temperature and pressure conditions

  3. Behavior of stainless steels in pressurized water reactor primary circuits

    NASA Astrophysics Data System (ADS)

    Féron, D.; Herms, E.; Tanguy, B.

    2012-08-01

    Stainless steels are widely used in primary circuits of pressurized water reactors (PWRs). Operating experience with the various grades of stainless steels over several decades of years has generally been excellent. Nevertheless, stress corrosion failures have been reported in few cases. Two main factors contributing to SCC susceptibility enhancement are investigated in this study: cold work and irradiation. Irradiation is involved in the stress corrosion cracking and corrosion of in-core reactor components in PWR environment. Irradiated assisted stress corrosion cracking (IASCC) is a complex and multi-physics phenomenon for which a predictive modeling able to describe initiation and/or propagation is not yet achieved. Experimentally, development of initiation smart tests and of in situ instrumentation, also in nuclear reactors, is an important axis in order to gain a better understanding of IASCC kinetics. A strong susceptibility for SCC of heavily cold worked austenitic stainless steels is evidenced in hydrogenated primary water typical of PWRs. It is shown that for a given cold-working procedure, SCC susceptibility of austenitic stainless steels materials increases with increasing cold-work. Results have shown also strong influences of the cold work on the oxide layer composition and of the maximum stress on the time to fracture.

  4. Metal release from stainless steel in biological environments: A review.

    PubMed

    Hedberg, Yolanda S; Odnevall Wallinder, Inger

    2016-03-01

    Due to its beneficial corrosion resistance, stainless steel is widely used in, e.g., biomedical applications, as surfaces in food contact, and for products intended to come into skin contact. Low levels of metals can be released from the stainless steel surface into solution, even for these highly corrosion resistant alloys. This needs to be considered in risk assessment and management. This review aims to compile the different metal release mechanisms that are relevant for stainless steel when used in different biological settings. These mechanisms include corrosion-induced metal release, dissolution of the surface oxide, friction-induced metal release, and their combinations. The influence of important physicochemical surface properties, different organic species and proteins in solution, and of biofilm formation on corrosion-induced metal release is discussed. Chemical and electrochemical dissolution mechanisms of the surface oxides of stainless steel are presented with a focus on protonation, complexation/ligand-induced dissolution, and reductive dissolution by applying a perspective on surface adsorption of complexing or reducing ligands and proteins. The influence of alloy composition, microstructure, route of manufacture, and surface finish on the metal release process is furthermore discussed as well as the chemical speciation of released metals. Typical metal release patterns are summarized. PMID:26514345

  5. Fabrication of stainless steel foil utilizing chromized steel strip

    NASA Astrophysics Data System (ADS)

    Loria, Edward A.

    1980-10-01

    Stainless steel foil has properties which are, in many respects, unmatched by alternative thin films. The high strength to weight ratio and resistance to corrosion and oxidation at elevated temperatures are generally advantageous. The aerospace and automotive industries have used Type 430 and 304 foil in turbine engine applications. Foil around 2 mils (5.1 × 10-3 cm) thick has been appropriate for the recuperator or heat exchanger and this product has also been used in honeycomb and truss-core structures. Further, such foil has been employed as a wrap to protect tool steel parts from contamination during heat treating. A large part of the high cost of producing stainless steel foil by rolling is due to the complicated and expensive rolling mill and annealing equipment involved. A method will be described which produces (solid) stainless steel foil from chromized (coated) steel which can be cheaper than the conventional processing stainless steel, such as Type 430, from ingot to foil. Also, the material is more ductile and less work hardenable during processing to foil and consequently intermediate annealing treatments are eliminated and scrap losses minimized.

  6. 304L stainless steel resistance to cesium chloride

    SciTech Connect

    Graves, C.E.

    1998-08-27

    B and W Hanford Company have two Oak Ridge National Laboratory (ORNL) Type 4 canisters filled with cesium chloride (CsCl) originally produced at WESF (Waste Encapsulation and Storage Facility). These canisters are constructed of 304L stainless steel per drawing ORNL 970-294. Instead of removing the CsCl from the Type 4 canisters and repacking into an Inner Capsule, it is intended (for ALARA, schedule and cost purposes) that the Type 4 canisters be decontaminated (scrubbed) and placed [whole] inside a Type ``W`` overpack. The overpack is constructed from 316L stainless steel. Several tests have been run by Pacific Northwest National Laboratory (PNNL) over the. years documenting the corrosion compatibility of 316L SS with CsCl (Bryan 1989 and Fullam 1972). However, no information for 304L SS compatibility is readily available. This document estimates the corrosion resistance of 304L stainless steel in a WESF CsCl environment as it compares with that of 316L stainless steel.

  7. [The question of nickel release from stainless steel cooking pots].

    PubMed

    Vrochte, H; Schätzke, M; Dringenberg, E; Wölwer-Rieck, U; Büning-Pfaue, H

    1991-09-01

    For three items of foods (rhubarb, spinach, sauerkraut) the possible release of nickel (by means of AAS) was analysed, a release which may be caused by a possible corrosive effect of the concerned (oxalic-, milk-, vinegar-) acids (as well as common salt) within a normal domestic food-preparation. For this analysis stainless steel cooking pots of different manufacturers, various types and in a representative selection and quantity were taken into consideration; the detailed analyses were extended so far that clear statistical evaluations were possible. This method complies regulations for accuracy to determine traces of heavy metal. For all three analysed food-stuffs an identical result was reached that no nickel release from the stainless steel cooking pots into the food was found. Differences of the various stainless steel cooking pots with regard to their surfaces' quality or their origin (manufacturers) were not yielded, either. All detected concentrations of nickel are within the reach of the natural nickel content of the analysed food-stuffs and their amount is even much lower than other food's content of nickel. This leads up to the conclusion that the former view of a possible nickel release of stainless steel cooking pots has to be revised because these assumptions were not confirmed in the presented results of this analysis and therefore have to be regarded as not correct. PMID:1763555

  8. 2. GENERAL VIEW OF STAINLESS STEEL SMOKEHOUSES ON LEVEL 6, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    2. GENERAL VIEW OF STAINLESS STEEL SMOKEHOUSES ON LEVEL 6, LOOKING EAST; SMOKEHOUSE UNITS WERE BUILT BY DRYING SYSTEMS COMPANY, DIVISION OF MICHIGAN OVEN COMPANY, MORTON GROVE, ILLINOIS - Rath Packing Company, Smokehouse-Hog Chilling Building, Sycamore Street between Elm & Eighteenth Streets, Waterloo, Black Hawk County, IA

  9. 6. DETAIL OF STAINLESS STEEL VISCERA CHUTE IN SOUTHEAST CORNER ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    6. DETAIL OF STAINLESS STEEL VISCERA CHUTE IN SOUTHEAST CORNER OF LEVEL4; ENTRAILS WERE DROPPED INTO CHUTE, THEN PASSED THROUGH THE FLOOR TO THE GUT SHANTY ON LEVEL 3 TO BE SORTED AND CLEANED - Rath Packing Company, Hog Dressing Building, Sycamore Street between Elm & Eighteenth Streets, Waterloo, Black Hawk County, IA

  10. 2012 ACCOMPLISHMENTS - TRITIUM AGING STUDIES ON STAINLESS STEELS

    SciTech Connect

    Morgan, M.

    2013-01-31

    This report summarizes the research and development accomplishments during FY12 for the tritium effects on materials program. The tritium effects on materials program is designed to measure the long-term effects of tritium and its radioactive decay product, helium-3, on the structural properties of forged stainless steels which are used as the materials of construction for tritium reservoirs. The FY12 R&D accomplishments include: (1) Fabricated and Thermally-Charged 150 Forged Stainless Steel Samples with Tritium for Future Aging Studies; (2) Developed an Experimental Plan for Measuring Cracking Thresholds of Tritium-Charged-and-Aged Steels in High Pressure Hydrogen Gas; (3) Calculated Sample Tritium Contents For Laboratory Inventory Requirements and Environmental Release Estimates; (4) Published report on “Cracking Thresholds and Fracture Toughness Properties of Tritium-Charged-and-Aged Stainless Steels”; and, (5) Published report on “The Effects of Hydrogen, Tritium, and Heat Treatment on the Deformation and Fracture Toughness Properties of Stainless Steels”. These accomplishments are highlighted here and references given to additional reports for more detailed information.

  11. Lithium wetting of stainless steel for plasma facing components

    NASA Astrophysics Data System (ADS)

    Skinner, C. H.; Capece, A. M.; Roszell, J. P.; Koel, B. E.

    2014-10-01

    Ensuring continuous wetting of a solid container by the liquid metal is a critical issue in the design of liquid metal plasma facing components foreseen for NSTX-U and FNSF. Ultrathin wetting layers may form on metallic surfaces under ultrahigh vacuum (UHV) conditions if material reservoirs are present from which spreading and wetting can start. The combined scanning electron microscopy (SEM), Auger electron spectroscopy (AES) and ion beam etching capabilities of a Scanning Auger Microprobe (SAM) have been used to study the spreading of lithium films on stainless steel substrates. A small (mm-scale) amount of metallic lithium was applied to a stainless steel surface in an argon glove box and transferred to the SAM. Native impurities on the stainless steel and lithium surfaces were removed by Ar+ ion sputtering. Elemental mapping of Li and Li-O showed that surface diffusion of Li had taken place at room temperature, well below the 181°C Li melting temperature. The influence of temperature and surface oxidation on the rate of Li spreading on stainless steel will be reported. Support was provided through DOE Contract Number DE-AC02-09CH11466.

  12. Graphene Nanoplatelets Based Protective and Functionalizing Coating for Stainless Steel.

    PubMed

    Mondal, Jayanta; Kozlova, Jekaterina; Sammelselg, Väino

    2015-09-01

    Stainless steel is the most widely used alloy for many industrial and everyday applications, and protection of this alloy substrate against corrosion is an important industrial issue. Here we report a promising application of graphene oxide and graphene nanoplatelets as effective corrosion inhibitors for AISI type 304 stainless steel alloy. The graphene oxide and graphene coatings on the stainless steel substrates were prepared using spin coating techniques. Homogeneous and complete surface coverage by the graphene oxide and graphene nanoplatelets were observed with a high-resolution scanning electron microscope. The corrosion inhibition ability of these materials was investigated through measurement of open circuit potential and followed by potentiodymamic polarization analysis in aqueous sodium chloride solution before and after a month of immersion. Analyzed result exhibits effective corrosion inhibition for both substrates coated with graphene oxide or graphene nanoplatelets by increasing corrosion potential, pitting potential and decreasing passive current density. The corrosion inhibition ability of the coated substrates has not changed even after the long-term immersion. The result showed both graphene materials can be used as an effective corrosion inhibitor for the stainless steel substrates, which would certainly increase lifetime the substrate. However, long-term protection ability of the graphene coated susbtsrate showed somewhat better inhibition performance than the ones coated with graphene oxide. PMID:26716239

  13. Reactor Material Program Fracture Toughness of Type 304 Stainless Steel

    SciTech Connect

    Awadalla, N.G.

    2001-03-28

    This report describes the experimental procedure for Type 304 Stainless Steel fracture toughness measurements and the application of results. Typical toughness values are given based on the completed test program for the Reactor Materials Program (RMP). Test specimen size effects and limitations of the applicability in the fracture mechanics methodology are outlined as well as a brief discussion on irradiation effects.

  14. 73. View of line of stainless steel coolant storage tanks ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    73. View of line of stainless steel coolant storage tanks for bi-sodium sulfate/water coolant solution at first floor of transmitter building no. 102. - Clear Air Force Station, Ballistic Missile Early Warning System Site II, One mile west of mile marker 293.5 on Parks Highway, 5 miles southwest of Anderson, Anderson, Denali Borough, AK

  15. Materials data handbook: Stainless steel alloy A-286

    NASA Technical Reports Server (NTRS)

    Muraca, R. F.; Whittick, J. S.

    1972-01-01

    A summary of the materials property information for stainless steel alloy A-286 is presented. The scope of the information includes physical and mechanical properties at cryogenic, ambient, and elevated temperatures. Information on material procurement, metallurgy of the alloy, corrosion, environmental effects, fabrication, and bonding is developed.

  16. Method of forming dynamic membrane on stainless steel support

    NASA Technical Reports Server (NTRS)

    Gaddis, Joseph L. (Inventor); Brandon, Craig A. (Inventor)

    1988-01-01

    A suitable member formed from sintered, powdered, stainless steel is contacted with a nitrate solution of a soluble alkali metal nitrate and a metal such as zirconium in a pH range and for a time sufficient to effect the formation of a membrane of zirconium oxide preferably including an organic polymeric material such as polyacrylic acid.

  17. Electroless nickel plating on stainless steels and aluminum

    NASA Technical Reports Server (NTRS)

    1966-01-01

    Procedures for applying an adherent electroless nickel plating on 303 SE, 304, and 17-7 PH stainless steels, and 7075 aluminum alloy was developed. When heat treated, the electroless nickel plating provides a hard surface coating on a high strength, corrosion resistant substrate.

  18. Bactericidal behavior of Cu-containing stainless steel surfaces

    NASA Astrophysics Data System (ADS)

    Zhang, Xiangyu; Huang, Xiaobo; Ma, Yong; Lin, Naiming; Fan, Ailan; Tang, Bin

    2012-10-01

    Stainless steels are one of the most common materials used in health care environments. However, the lack of antibacterial advantage has limited their use in practical application. In this paper, antibacterial stainless steel surfaces with different Cu contents have been prepared by plasma surface alloying technology (PSAT). The steel surface with Cu content 90 wt.% (Cu-SS) exhibits strong bactericidal activity against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) within 3 h. Although the Cu-containing surface with Cu content 2.5 wt.% (CuNi-SS) can also kill all tested bacteria, this process needs 12 h. SEM observation of the bacterial morphology and an agarose gel electrophoresis were performed to study the antibacterial mechanism of Cu-containing stainless steel surfaces against E. coli. The results indicated that Cu ions are released when the Cu-containing surfaces are in contact with bacterial and disrupt the cell membranes, killing the bacteria. The toxicity of Cu-alloyed surfaces does not cause damage to the bacterial DNA. These results provide a scientific explanation for the antimicrobial applications of Cu-containing stainless steel. The surfaces with different antibacterial abilities could be used as hygienic surfaces in healthcare-associated settings according to the diverse requirement of bactericidal activities.

  19. Failure Assessment Diagram for Brazed 304 Stainless Steel Joints

    NASA Technical Reports Server (NTRS)

    Flom, Yory

    2011-01-01

    Interaction equations were proposed earlier to predict failure in Albemet 162 brazed joints. Present study demonstrates that the same interaction equations can be used for lower bound estimate of the failure criterion in 304 stainless steel joints brazed with silver-based filler metals as well as for construction of the Failure Assessment Diagrams (FAD).

  20. Alternative to Nitric Acid for Passivation of Stainless Steel Alloys

    NASA Technical Reports Server (NTRS)

    Lewis, Pattie L.; Kolody, Mark; Curran, Jerry

    2013-01-01

    Corrosion is an extensive problem that affects the Department of Defense (DoD) and National Aeronautics and Space Administration (NASA). The deleterious effects of corrosion result in steep costs, asset downtime affecting mission readiness, and safety risks to personnel. Consequently, it is vital to reduce corrosion costs and risks in a sustainable manner. The DoD and NASA have numerous structures and equipment that are fabricated from stainless steel. The standard practice for protection of stainless steel is a process called passivation. Typical passivation procedures call for the use of nitric acid; however, there are a number of environmental, worker safety, and operational issues associated with its use. Citric acid offers a variety of benefits including increased safety for personnel, reduced environmental impact, and reduced operational cost. DoD and NASA agreed to collaborate to validate citric acid as an acceptable passivating agent for stainless steel. This paper details our investigation of prior work developing the citric acid passivation process, development of the test plan, optimization of the process for specific stainless steel alloys, ongoing and planned testing to elucidate the process' resistance to corrosion in comparison to nitric acid, and preliminary results.

  1. Effect of ultrafine grain on tensile behaviour and corrosion resistance of the duplex stainless steel.

    PubMed

    Jinlong, Lv; Tongxiang, Liang; Chen, Wang; Limin, Dong

    2016-05-01

    The ultrafine grained 2205 duplex stainless steel was obtained by cold rolling and annealing. The tensile properties were investigated at room temperature. Comparing with coarse grained stainless steel, ultrafine grained sample showed higher strength and plasticity. In addition, grain size changed deformation orientation. The strain induced α'-martensite was observed in coarse grained 2205 duplex stainless steel with large strain. However, the grain refinement inhibited the transformation of α'-martensite;nevertheless, more deformation twins improved the strength and plasticity of ultrafine grained 2205 duplex stainless steel. In addition, the grain refinement improved corrosion resistance of the 2205 duplex stainless steel in sodium chloride solution. PMID:26952459

  2. Tuning the electronic properties of Ti-MoS2 contacts through introducing vacancies in monolayer MoS2.

    PubMed

    Feng, Li-ping; Su, Jie; Li, Da-peng; Liu, Zheng-tang

    2015-03-14

    The effect of vacancies in monolayer MoS2 on the electronic properties of a Ti-MoS2 top contact has been investigated using first-principles calculations. A Mo-vacancy is easier to form than a S-vacancy in a Ti-MoS2 top contact, especially under oxidation conditions. A Mo-vacancy eliminates the Schottky barrier of the Ti-MoS2 top contact, and a S-vacancy reduces the Schottky barrier from 0.28 to 0.15 eV. Mo-vacancies are beneficial for obtaining a high quality p-type Ti-MoS2 top contact, whereas S-vacancies are favorable to achieve a high quality n-type Ti-MoS2 top contact. Moreover, defective Ti-MoS2 top contacts have stronger dipole layers, a higher potential step and more transferred charges than a perfect ones. The electronic properties of Ti-MoS2 top contacts can be tuned by intrinsic vacancies in monolayer MoS2. Our findings provide important insights into the future design and fabrication of novel nanoelectronic devices with monolayer MoS2. PMID:25679945

  3. 78 FR 31998 - Missouri Disaster #MO-00064

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-05-28

    ... ADMINISTRATION Missouri Disaster MO-00064 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY...: Submit completed loan applications to: U.S. Small Business Administration, Processing and Disbursement... of Disaster Assistance, U.S. Small Business Administration, 409 3rd Street SW., Suite...

  4. Accelerator Production Options for 99MO

    SciTech Connect

    Bertsche, Kirk; /SLAC

    2010-08-25

    Shortages of {sup 99}Mo, the most commonly used diagnostic medical isotope, have caused great concern and have prompted numerous suggestions for alternate production methods. A wide variety of accelerator-based approaches have been suggested. In this paper we survey and compare the various accelerator-based approaches.

  5. 78 FR 56978 - Missouri Disaster #MO-00068

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-16

    ... ADMINISTRATION Missouri Disaster MO-00068 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY.... ADDRESSES: Submit completed loan applications to: U.S. Small Business Administration, Processing And..., Office of Disaster Assistance, U.S. Small Business Administration, 409 3rd Street SW., Suite...

  6. 76 FR 18289 - Missouri Disaster #MO-00047

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-01

    ... ADMINISTRATION Missouri Disaster MO-00047 AGENCY: U.S. Small Business Administration. ACTION: Notice. SUMMARY...: Submit completed loan applications to: U.S. Small Business Administration, Processing and Disbursement... of Disaster Assistance, U.S. Small Business Administration, 409 3rd Street, SW., Suite...

  7. Polarity control in MoS2 and MoSe2 field effect transistors

    NASA Astrophysics Data System (ADS)

    Fragapane, A.; Bobek, S.; Barroso, D.; Nguyen, A.; Bonilla, E.; Naghibi, S.; von Son Palacio, G.; Klee, V.; Preciado, E.; Martinez, J.; Pleskot, D.; Mann, J.; Shidpoor, R.; Bartels, L.; Sorger, V.; Liu, A.; Paranjape, M.; Barbara, P.

    2014-03-01

    Ambipolar operation is essential for a variety of optoelectronic applications, where both electron and hole transport are required simultaneously. However, hole transport and p-type Schottky barriers have been difficult to achieve in all-solid state field effect transistors based on MoS2 charge channels. In prior work we demonstrated that Schottky barriers of either polarity (p-type or n-type) can be obtained with multilayer MoS2 flakes exfoliated from geological crystals. Here we study Schottky barrier polarity in thinner flakes of MoS2 and MoSe2 (down to single-layer thicknesses) that are grown by CVD, towards understanding how both variations in the bandgap and material work functions affect band alignment at the interface between the flakes and the metal contacts. Supported by the NSF, DMR-1008242, 1106210 and C-SPIN.

  8. Effect of solution annealing temperature on precipitation in 2205 duplex stainless steel

    SciTech Connect

    Kashiwar, A.; Vennela, N. Phani; Kamath, S.L.; Khatirkar, R.K.

    2012-12-15

    In the present study, effect of solution annealing temperature (1050 Degree-Sign C and 1100 Degree-Sign C) and isothermal ageing (700 Degree-Sign C: 15 min to 6 h) on the microstructural changes in 2205 duplex stainless steel has been investigated systematically. Scanning electron microscopy and X-ray diffraction were adopted to follow the microstructural evolution, while an energy dispersive spectrometer attached to scanning electron microscope was used to obtain localised chemical information of various phases. The ferritic matrix of the two phase 2205 duplex stainless steel ({approx} 45% ferrite and {approx} 55% austenite) undergoes a series of metallurgical transformations during ageing-formation of secondary austenite ({gamma}{sub 2}) and precipitation of Cr and Mo rich intermetallic (chi-{chi} and sigma-{sigma}) phases. For solution annealing at 1050 Degree-Sign C, significant amount of carbides were observed in the ferrite grains after 1 h of ageing at 700 Degree-Sign C. {chi} Phase precipitated after the precipitation of carbides-preferentially at the ferrite-ferrite and also at the ferrite-austenite boundaries. {sigma} Phase was not observed in significant quantity even after 6 h of ageing. The sequence of precipitation in samples solution annealed at 1050 Degree-Sign C was found to be carbides {yields} {chi} {yields} {sigma}. On the contrary, for samples solution annealed at 1100 Degree-Sign C, the precipitation of {chi} phase was negligible. {chi} Phase precipitated before {sigma} phase, preferentially along the ferrite-ferrite grain boundaries and was later consumed in the {sigma} phase precipitation. The {sigma} phase precipitated via the eutectoid transformation of ferrite to yield secondary austenite {gamma}{sub 2} and {sigma} phase in the ferrite and along the ferrite-austenite grain boundaries. An increase in the volume fraction of {gamma}{sub 2} and {sigma} phase with simultaneous decrease in the ferrite was evidenced with ageing. - Highlights

  9. Fatigue Crack Growth Behavior of Gas Metal Arc Welded AISI 409 Grade Ferritic Stainless Steel Joints

    NASA Astrophysics Data System (ADS)

    Lakshminarayanan, A. K.; Shanmugam, K.; Balasubramanian, V.

    2009-10-01

    The effect of filler metals such as austenitic stainless steel, ferritic stainless steel, and duplex stainless steel on fatigue crack growth behavior of the gas metal arc welded ferritic stainless steel joints was investigated. Rolled plates of 4 mm thickness were used as the base material for preparing single ‘V’ butt welded joints. Center cracked tensile specimens were prepared to evaluate fatigue crack growth behavior. Servo hydraulic controlled fatigue testing machine with a capacity of 100 kN was used to evaluate the fatigue crack growth behavior of the welded joints. From this investigation, it was found that the joints fabricated by duplex stainless steel filler metal showed superior fatigue crack growth resistance compared to the joints fabricated by austenitic and ferritic stainless steel filler metals. Higher yield strength and relatively higher toughness may be the reasons for superior fatigue performance of the joints fabricated by duplex stainless steel filler metal.

  10. Semitransparent inverted polymer solar cells with MoO3/Ag/MoO3 as transparent electrode

    NASA Astrophysics Data System (ADS)

    Tao, Chen; Xie, Guohua; Liu, Caixia; Zhang, Xindong; Dong, Wei; Meng, Fanxu; Kong, Xiangzi; Shen, Liang; Ruan, Shengping; Chen, Weiyou

    2009-08-01

    Semitransparent inverted polymer solar cells were developed using thermally evaporable MoO3/Ag/MoO3 as transparent anode. The ultrathin inner MoO3 layer was introduced as a buffer layer to improve hole collection, while the outer MoO3 layer served as a light coupling layer to enhance optical transmittance of the device. The dependence of the device performances on the thickness of the outer MoO3 layer was investigated. The results showed that the addition of the outer MoO3 layer improves the transmittance of the anode compared to MoO3/Ag anode and the performances of the semitransparent devices with the outer MoO3 layer are improved due to the reduced series resistance.

  11. Pressure evolution of the potential barriers of phase transition of MoS2, MoSe2 and MoTe2.

    PubMed

    Fan, Xaiofeng; Singh, David J; Jiang, Q; Zheng, W T

    2016-04-28

    Two-dimensional crystals with weak layer interactions, such as twisted graphene, have been a focus of research recently. As a representative example, transitional metal dichalcogenides show a lot of fascinating properties due to stacking orders and spin-orbit coupling. We analyzed the dynamic energy barrier of possible phase transitions in MoX2 (X = S, Se and Te) with first-principles methods. In the structural transition from 2Hc to 2Ha, the energy barrier is found to be increased following an increase of pressure which is different from the phase transition in usual semiconductors. Among MoS2, MoSe2 and MoTe2, the energy barrier of MoS2 is the lowest and the stability of both 2Hc and 2Ha is reversed under pressure for MoS2. It is found that the absence of a phase transition in MoSe2 and MoTe2 is due to the competition between van der Waals interaction of layers and the coulomb interaction of Mo and X in nearest-neighbor layer of Mo in both phases. PMID:27074155

  12. Novel architectured metal-supported solid oxide fuel cells with Mo-doped SrFeO3-δ electrocatalysts

    NASA Astrophysics Data System (ADS)

    Zhou, Yucun; Meng, Xie; Liu, Xuejiao; Pan, Xin; Li, Junliang; Ye, Xiaofeng; Nie, Huaiwen; Xia, Changrong; Wang, Shaorong; Zhan, Zhongliang

    2014-12-01

    Barriers to technological advancement of metal-supported SOFCs include nickel coarsening in the anode, metallic interdiffusion between the anode and the metal substrate, as well as poor cathode adhesion. Here we report a robust and novel architectured metal-supported SOFC that consists of a thin dense yttria-stabilized zirconia (YSZ) electrolyte layer sandwiched between a porous 430L stainless steel substrate and a porous YSZ thin layer. The key feature is simultaneous use of impregnated nano-scale SrFe0.75Mo0.25O3-δ coatings on the internal surfaces of the porous 430L and YSZ backbones respectively as the anode and cathode catalyst. Such a fuel cell exhibits power densities of 0.74 W cm-2 at 800 °C and 0.40 W cm-2 at 700 °C when operating on hydrogen fuels and air oxidants.

  13. Low Temperature Surface Carburization of Stainless Steels

    SciTech Connect

    Collins, Sunniva R; Heuer, Arthur H; Sikka, Vinod K

    2007-12-07

    Low-temperature colossal supersaturation (LTCSS) is a novel surface hardening method for carburization of austenitic stainless steels (SS) without the precipitation of carbides. The formation of carbides is kinetically suppressed, enabling extremely high or colossal carbon supersaturation. As a result, surface carbon concentrations in excess of 12 at. % are routinely achieved. This treatment increases the surface hardness by a factor of four to five, improving resistance to wear, corrosion, and fatigue, with significant retained ductility. LTCSS is a diffusional surface hardening process that provides a uniform and conformal hardened gradient surface with no risk of delamination or peeling. The treatment retains the austenitic phase and is completely non-magnetic. In addition, because parts are treated at low temperature, they do not distort or change dimensions. During this treatment, carbon diffusion proceeds into the metal at temperatures that constrain substitutional diffusion or mobility between the metal alloy elements. Though immobilized and unable to assemble to form carbides, chromium and similar alloying elements nonetheless draw enormous amounts of carbon into their interstitial spaces. The carbon in the interstitial spaces of the alloy crystals makes the surface harder than ever achieved before by more conventional heat treating or diffusion process. The carbon solid solution manifests a Vickers hardness often exceeding 1000 HV (equivalent to 70 HRC). This project objective was to extend the LTCSS treatment to other austenitic alloys, and to quantify improvements in fatigue, corrosion, and wear resistance. Highlights from the research include the following: • Extension of the applicability of the LTCSS process to a broad range of austenitic and duplex grades of steels • Demonstration of LTCSS ability for a variety of different component shapes and sizes • Detailed microstructural characterization of LTCSS-treated samples of 316L and other alloys

  14. β-Nd2Mo4O15

    PubMed Central

    Zhao, Dan; Li, Fei-Fei; Yao, Yu-Ming; Huan, Chang-An; Zhao, En-Xiao

    2010-01-01

    The title compound, dineodymium(III) tetra­molybdate(VI), has been prepared by a flux technique and is the second polymorph of composition Nd2Mo4O15. The crystal structure is isotypic with those of Ce2Mo4O15 and Pr2Mo4O15. It features a three-dimensional network composed of distorted edge- and corner-sharing NdO7 polyhedra, NdO8 polyhedra, MoO4 tetra­hedra and MoO6 octa­hedra. PMID:21589208

  15. Effect of composition, cooling rate, and solidification velocity on the microstructural development of molybdenum-bearing stainless steels

    NASA Astrophysics Data System (ADS)

    Perricone, Matthew J.

    A series of Mo-bearing stainless steel compositions ranging from 0 to 10 wt% Mo were analyzed over a range of laser welding conditions to evaluate the effect of composition, cooling rate, and solidification velocity on microstructural development. Of particular engineering interest are alloys expected to solidify as primary delta-ferrite and transform in the solid state to gamma-austenite. Such compositions are essentially immune to solidification cracking and can potentially eliminate microsegregation (due to primary ferrite solidification) while still having high toughness and no magnetic signature at room temperature (transformation to austenite). A total of 64 Fe-Ni-Cr-Mo compositions were chosen based on multi-component phase stability diagrams calculated using the CALPHAD method. Alloys were created using the arc button melting process and laser welds were prepared on each alloy at constant power and travel speeds ranging from 4.2 mm/s to 42 mm/s. The cooling rates of these processes were estimated to range from 10 °C/s for are buttons to 105 °C/s for the fastest laser welds. Microstructural analysis was completed to determine primary solidification mode and the nature of solid state transformation behavior. Good agreement was observed between experimental observations and predictions from thermodynamic calculations. No shift in solidification mode was observed from primary delta-ferrite to primary gamma-austenite in the range of welding conditions studied. Metastable microstructural features were observed in many laser weld fusion zones, as well as a massive transformation from delta-ferrite to gamma-austenite in many of the alloys exhibiting primary delta-ferrite solidification. Evidence of epitaxial massive growth without nucleation was also found in primary delta-ferrite alloys with intercellular gamma-austenite already present from a solidification reaction. The resulting single phase gamma-austenite in both cases exhibited a homogenous distribution of

  16. Accelerated corrosion of stainless steel in thiocyanate-containing solutions

    SciTech Connect

    Pistorius, P Chris; Li, Wen

    2012-09-19

    It is known that reduced sulfur compounds (such as thiocyanate and thiosulfate) can accelerate active corrosion of austenitic stainless steel in acid solutions, but before we started this project the mechanism of acceleration was largely unclear. This work combined electrochemical measurements and analysis using scanning electron microscopy (SEM) and X-ray photo-electron spectroscopy (XPS), which provided a comprehensive understanding of the catalytic effect of reduced sulfur species on the active corrosion of stainless steel. Both the behavior of the pure elements and the steel were studied and the work focused on the interaction between the pure elements of the steel, which is the least understood area. Upon completion of this work, several aspects are now much clearer. The main results from this work can be summarized as follows: The presence of low concentrations (around 0.1 mM) of thiocyanate or tetrathionate in dilute sulfuric acid greatly accelerates the anodic dissolution of chromium and nickel, but has an even stronger effect on stainless steels (iron-chromium-nickel alloys). Electrochemical measurements and surface analyses are in agreement with the suggestion that accelerated dissolution really results from suppressed passivation. Even well below the passivation potential, the electrochemical signature of passivation is evident in the electrode impedance; the electrode impedance shows clearly that this pre-passivation is suppressed in the presence of thiocyanate. For the stainless steels, remarkable changes in the morphology of the corroded metal surface and in the surface concentration of chromium support the suggestion that pre-passivation of stainless steels is suppressed because dissolution of chromium is accelerated. Surface analysis confirmed that adsorbed sulfur / sulfide forms on the metal surfaces upon exposure to solutions containing thiocyanate or thiosulfate. For pure nickel, and steels containing nickel (and residual copper), bulk sulfide

  17. Foamability of stainless steelmaking slags in an EAF

    NASA Astrophysics Data System (ADS)

    Kerr, James John

    Foaming in electric furnace steelmaking is desirable to allow for a longer arc and subsequently higher power operation in order to reduce the tap to tap time and consequently increase productivity. Stainless steelmaking slags do not foam as well as carbon steelmaking slags. To produce foam, the foamability or foam index of a slag and the gas generation rate must be adequate. The possible causes for the poor foamability of stainless steelmaking slags were examined in this research. Specifically the foam index of a simulated stainless steelmaking slag containing chrome oxide was measured and the rate at which carbon reacts with Cr2O3, CrO, and FeO was also measured. The experimental results show that the foam index of stainless steelmaking slags is comparable to carbon steelmaking slags provided that the amount of solid chrome oxide particles or complexes is not excessive. This indicates the low foamability is not due to a poor foam index. Gas is normally generated by cycling carbon into the slag, which produces CO by reducing oxides in the slag. The experimental results demonstrate that the reaction rate of carbon with CrO dissolved in the slag and hence the generation of CO is significantly slower than for the reaction rate of carbon with FeO dissolved in slags. Therefore, the lack of FeO or other reducible oxides in stainless steelmaking slags is a primary reason for the poor foamability. Experimental results indicate that limestone, nickel oxide, calcium nitrate, and waste oxide briquettes generate gas at sufficient rates to induce foaming when added to the stainless steelmaking slag. Heat transfer most likely controls the rate of CO2 generated by limestone and NiO reduction is controlled by mass transfer of NiO to the carbon in the slag. WOBs generate gas very rapidly due to intimate mixing of the carbon and iron oxides at unit activity. Calcium nitrate generates gas by dissociation and heat transfer likely controls the dissociation rate. Simple models are

  18. A study of Mo-V and Mo-V-Fe alloys for conductive cermet applications

    SciTech Connect

    Stephens, J.J.; Damkroger, B.K.; Ewsuk, K.G.; Glass, S.J.; Monroe, S.L.; Reece, M.; Smugeresky, J.E.

    1998-06-01

    Molybdenum and alumina cermets are currently being used for small, simple geometry, electrical feed-throughs in insulating alumina ceramic bodies. However, with larger and more complex geometries, high residual stresses and cracking of the alumina ceramic occur due to differences in coefficient of thermal expansion (CTE) between cermet and the surrounding 94% alumina. The difference in CTE is caused by the Mo in the cermet, which lowers the CTE of the cermet relative to the 94% alumina ceramic. A study was conducted at Sandia National Laboratories to develop CTE-matched cermets based on binary Mo-V and ternary Mo-V-X alloy systems. It was found that the CTE of 94% alumina (over the range 1,000 C to room temperature) could be precisely matched by a binary Mo-32.5V alloy. However, to address concerns regarding the selective oxidation of V, Mo-V-X alloys with CTE`s similar to 94% alumina were made with Fe or Co additions. The ternary additions are limited to about 3 wt.% to maintain a single phase BCC alloy, and permit some reduction in the V addition. Powders were fabricated from both Mo-27V and Mo-22V-3Fe, and were evaluated in 3 hr./1,625 C cermet sintering trials. The results of those trials suggest that extensive reaction occurs between the Vanadium component of the alloy and the alumina ceramic. In view of these results the authors have begun to evaluate the feasibility of fabricating Iridium alumina cermets. Iridium is an attractive choice due to its close CTE match to 94% alumina ceramic. Preliminary results indicate there is no detrimental reaction between the Iridium and alumina phases.

  19. Electronic Coupling in [Mo2]-Bridge-[Mo2] Systems with Twisted Bridges.

    PubMed

    Zhang, Hong Li; Zhu, Guang Yuan; Wang, Gangyi; Meng, Miao; Liu, Chun Y; Lei, Hao

    2015-12-01

    In order to evaluate the impact of bridge conformation on electronic coupling in donor-bridge-acceptor triad systems, two Mo2 dimers, [Mo2(DAniF)3]2[μ-1,4-{C(O)NH}2-Naph] (1, DAniF = N,N'-di(p-anisyl)formamidinate and Naph = naphthalenyl) and [Mo2(DAniF)3]2[μ-1,4-(CS2)2-2,5-Me2C6H2] (2), have been synthesized and structurally characterized. These two compounds feature a large dihedral angle (>60°) between the central aromatic ring and the plane defined by the Mo-Mo bond vectors, which is distinct from the previously reported phenylene bridged analogues [Mo2(DAniF)3]2[μ-1,4-{C(O)NH}2-ph] (I) and [Mo2(DAniF)3]2[μ-1,4-(CS2)2-C6H4] (II), respectively. Unusual optical behaviors are observed for the mixed-valence (MV) species (1(+) and 2(+)), generated by single-electron oxidation. While 2(+) exhibits a weak intervalence charge transfer (IVCT) absorption band in the near-IR region, the IVCT band is absent in the spectrum of 1(+), which is quite different from what observed for I(+) and II(+). Optical analyses, based on superexchange formalism and Hush model, indicate that, in terms of Robin-Day classification, mixed-valence species 1(+) belongs to the electronically uncoupled Class I and complex 2(+), with Hab = 220 cm(-1), is assigned to the weakly coupled Class II. Together with I(+) and II(+), the four MV complexes complete a transition from Class I to Class II-III borderline as a result of manipulating the geometric topology of the bridge. Given the structural and electronic features for the molecular systems, the impacts of electrostatic interaction (through-space) and electron resonance (through-bond) on electronic coupling are discussed. PMID:26579936

  20. The effect of dose rate on the response of austenitic stainless steels to neutron radiaiton

    SciTech Connect

    Allen, T. R.; Cole, J I.; Trybus, Carole L.; Porter, D. L.; Tsai, Hanchung; Garner, Francis A.; Kenik, E A.; Yoshitake, T.; Ohta, Joji

    2006-01-01

    Depending on reactor design and component location, austenitic stainless steels may experience significantly different irradiation dose rates in the same reactor. Understanding the effect of dose rate on radiation performance is important to predicting component lifetime. This study examined the effect of dose rate on swelling, grain boundary segregation, and tensile properties in austenitic stainless steels through the examination of components retrieved from the Experimental Breeder Reactor-II (EBR-II) following its shutdown. Annealed 304 stainless steel, stress-relieved 304 stainless steel, 12% cold-worked 316 stainless steel, and 20% cold-worked 316 stainless steel were irradiated over a dose range of 1-56 dpa at temperatures from 371 to 440 C and dose rates from 0.5 to 5.8 ? 10*7 dpa/s. Density and tensile properties were measured for 304 and 316 stainless steel. Changes in grain boundary composition were examined for 304 stainless steel. Swelling appears to increase at lower dose rates in both 304 and 316 stainless steel, although the effect was not always statistically significant. Grain boundary segregation also appears to increase at lower dose rate in 304 stainless steel. For the range of dose rates examined, no measurable dose rate effect on tensile properties was noted for any of the steels.

  1. Re Effects on Phase Stability and Mechanical Properties of MoSS+Mo3Si+Mo5SiB2 alloys

    SciTech Connect

    Yang, Ying; Bei, Hongbin; George, Easo P; Tiley, Jaimie

    2013-01-01

    Because of their high melting points and good oxidation resistance Mo-Si-B alloys are of interest as potential ultrahigh-temperature structural materials. But their major drawbacks are poor ductility and fracture toughness at room temperature. Since alloying with Re has been suggested as a possible solution, we investigate here the effects of Re additions on the microstructure and mechanical properties of a ternary alloy with the composition Mo-12.5Si-8.5B (at.%). This alloy has a three-phase microstructure consisting of Mo solid-solution (MoSS), Mo3Si, and Mo5SiB2 and our results show that up to 8.4 at.% Re can be added to it without changing its microstructure or forming any brittle phase at 1600 C. Three-point bend tests using chevron-notched specimens showed that Re did not improve fracture toughness of the three-phase alloy. Nanoindentation performed on the MoSS phase in the three-phase alloy showed that Re increases Young s modulus, but does not lower hardness as in some Mo solid solution alloys. Based on our thermodynamic calculations and microstructural analyses, the lack of a Re softening effect is attributed to the increased Si levels in the Re-containing MoSS phase since Si is known to increase its hardness. This lack of softening is possibly why there is no Re-induced improvement in fracture toughness.

  2. Preparation of MoO2 by the Solid State Reaction Between MoS2 and MoO3

    NASA Astrophysics Data System (ADS)

    Wang, Lu; Bu, Chun-Yang; Zhang, Guo-Hua; Jiang, Tao; Chou, Kuo-Chih

    2016-03-01

    In the present study, the solid state reactions between molybdenum disulfide (MoS2) and molybdenum trioxide (MoO3) under different mixing molar ratios and different reaction temperatures have been investigated in order to produce industrial grade molybdenum dioxide (MoO2). It was found that it was difficult to react completely when the temperature was less than 873 K. However, when the temperature was up to 923 K or 973 K, the final product MoO2 with low residual sulfur can be obtained. Results of the residual sulfur levels at different conditions show that the content of residual sulfur decreases with the increase of temperature. In addition, the excess additions of MoO3 are effective and necessary in order to decrease the residual sulfur level. When the mixing molar ratio of MoS2 to MoO3 is 1:6.5, the content of residual sulfur can decrease down to 0.075% at 973 K. It was also found that the reaction between MoS2 and MoO3 obeyed the shrinking core model.

  3. A high Cr-Mo alloy iron

    SciTech Connect

    Huang, X.; Wu, Y.

    1998-08-01

    The structure, hardness, abrasion, and erosion wear of Cr-Mo white iron (containing approximately 28% Cr and 1% Mo) heat treated at certain temperatures were studied. Results show that the heat treatment of white iron changes the structures and properties; that is morphology, amount, size, and distribution of secondary phases are affected. When white iron was heated at 800 to 850 C the secondary phase precipitated at the phase boundary, making the abrasion and erosion wear worse. When the iron was heated at 900 to 950 C, the secondary phase precipitated dispersively at the matrix, and the corrosion wear was optimum. If the iron is heated at 1000 to 1050 C, the resistance of abrasion is inhibited, as the secondary phases precipitate in large amounts, and the hardness is increased. When the white iron is tempered at 500 to 600 C, the resistance of abrasion is better.

  4. Status of Genesis Mo-Pt Foils

    NASA Technical Reports Server (NTRS)

    Nishiizumi, K.; Allton, J. H.; Burnett, D. S.; Butterworth, A. L.; Caffee, M. W.; Clark, B.; Jurewicz, A. J. G.; Komura, K.; Westphal, A. J.; Welten, K. C.

    2005-01-01

    A total of 8,000 sq cm of Mo-coated Pt foils were exposed to solar wind for 884 days by the Genesis mission. Solar wind ions were captured in the surface of the Mo. Our objective is the measurement of long-lived radionuclides, such as Be-10, Al-26, Cl-36, and Mn-53, and short-lived radionuclides, such as Na-22 and Mn-54, in the captured sample of solar wind. The expected flux of these nuclides in the solar wind is 100 atom/sq cm yr or less. The hard landing of the SRC (Sample Return Capsule) at UTTR (Utah Test and Training Range) has resulted in contaminated and crumpled foils. Here we present a status report and revised plan for processing the foils.

  5. Highly stretchable MoS2 kirigami.

    PubMed

    Hanakata, Paul Z; Qi, Zenan; Campbell, David K; Park, Harold S

    2016-01-01

    We report the results of classical molecular dynamics simulations focused on studying the mechanical properties of MoS2 kirigami. Several different kirigami structures were studied based upon two simple non-dimensional parameters, which are related to the density of cuts, as well as the ratio of the overlapping cut length to the nanoribbon length. Our key findings are significant enhancements in tensile yield (by a factor of four) and fracture strains (by a factor of six) as compared to pristine MoS2 nanoribbons. These results, in conjunction with recent results on graphene, suggest that the kirigami approach may be generally useful for enhancing the ductility of two-dimensional nanomaterials. PMID:26628005

  6. Highly stretchable MoS2 kirigami

    NASA Astrophysics Data System (ADS)

    Hanakata, Paul Z.; Qi, Zenan; Campbell, David K.; Park, Harold S.

    2015-12-01

    We report the results of classical molecular dynamics simulations focused on studying the mechanical properties of MoS2 kirigami. Several different kirigami structures were studied based upon two simple non-dimensional parameters, which are related to the density of cuts, as well as the ratio of the overlapping cut length to the nanoribbon length. Our key findings are significant enhancements in tensile yield (by a factor of four) and fracture strains (by a factor of six) as compared to pristine MoS2 nanoribbons. These results, in conjunction with recent results on graphene, suggest that the kirigami approach may be generally useful for enhancing the ductility of two-dimensional nanomaterials.

  7. Kinetics and mechanism of thermal aging embrittlement of duplex stainless steels

    SciTech Connect

    Chung, H.M.; Chopra, O.K.

    1987-06-01

    Microstructural characteristics of long-term-aged cast duplex stainless steel specimens from eight laboratory heats and an actual component from a commercial boiling water reactor have been investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), small angle neutron scattering (SANS), and atom probe field ion microscopy (APFIM) techniques. Three precipitate phases, i.e., Cr-rich ..cap alpha..' and the Ni- and Si-rich G phase, and ..gamma../sub 2/ austenite, have been identified in the ferrite matrix of the aged specimens. For CF-8 grade materials, M/sub 23/C/sub 6/ carbides were identified on the austenite-ferrite boundaries as well as in the ferrite matrix for aging at greater than or equal to 450/sup 0/C. It has been shown that Si, C, and Mo contents are important factors that influence the kinetics of the G-phase precipitation. However, TEM and APFIM analyses indicate that the embrittlement for less than or equal to400/sup 0/C aging is primarily associated with Fe and Cr segregation in ferrite by spinodal decomposition. For extended aging, e.g., 6 to 8 years at 350 to 400/sup 0/C, large platelike ..cap alpha..' formed by nucleation and growth from the structure produced by the spinodal decomposition. The Cr content appears to play an important role either to promote the platelike ..cap alpha..' (high Cr content) or to suppress the ..cap alpha..' in favor of ..gamma../sub 2/ precipitation (low Cr). Approximate TTT diagrams for the spinodal, ..cap alpha..', G, ..gamma../sub 2/, and the in-ferrite M/sub 23/C/sub 6/ have been constructed for 250 to 450/sup 0/C aging. Microstructural modifications associated with a 550/sup 0/C reannealing and a subsequent toughness restoration are also discussed. It is shown that the toughness restoration is associated primarily with the dissolution of the Cr-rich region in ferrite.

  8. Hydrogen transport through stainless steel under plasma irradiation

    NASA Astrophysics Data System (ADS)

    Airapetov, A. A.; Begrambekov, L. B.; Kaplevsky, A. S.; Sadovskiy, Ya A.

    2016-01-01

    The paper presents the results of investigation of gas exchange through stainless steel surface of the plasma chamber under irradiation with hydrogen atoms in oxygen atmosphere or oxygen contaminated hydrogen plasma. Dependence of this process on various irradiation parameters, such as the metal temperature, energy of irradiating ions, gas composition of plasma are studied. It is shown, that desorption from stainless steel is activated with the increase of the plasma chamber walls temperature and energy of irradiating ions. Hydrogen release occurs also under irradiation of the walls by helium and argon plasmas added with oxygen, however the amount of released hydrogen is several times lower than in the case of irradiation with oxygen contaminated deuterium plasma.

  9. Failure Assessment of Stainless Steel and Titanium Brazed Joints

    NASA Technical Reports Server (NTRS)

    Flom, Yury A.

    2012-01-01

    Following successful application of Coulomb-Mohr and interaction equations for evaluation of safety margins in Albemet 162 brazed joints, two additional base metal/filler metal systems were investigated. Specimens consisting of stainless steel brazed with silver-base filler metal and titanium brazed with 1100 Al alloy were tested to failure under combined action of tensile, shear, bending and torsion loads. Finite Element Analysis (FEA), hand calculations and digital image comparison (DIC) techniques were used to estimate failure stresses and construct Failure Assessment Diagrams (FAD). This study confirms that interaction equation R(sub sigma) + R(sub tau) = 1, where R(sub sigma) and R(sub t u) are normal and shear stress ratios, can be used as conservative lower bound estimate of the failure criterion in stainless steel and titanium brazed joints.

  10. Inhibition of Sodium Benzoate on Stainless Steel in Tropical Seawater

    SciTech Connect

    Seoh, S. Y.; Senin, H. B.; Nik, W. N. Wan; Amin, M. M.

    2007-05-09

    The inhibition of sodium benzoate for stainless steel controlling corrosion was studied in seawater at room temperature. Three sets of sample have been immersed in seawater containing sodium benzoate with the concentrations of 0.3M, 0.6M and 1.0M respectively. One set of sample has been immersed in seawater without adding any sodium benzoate. It was found that the highest corrosion rate was observed for the stainless steel with no inhibitor was added to the seawater. As the concentration of sodium benzoate being increased, the corrosion rate is decreases. Results show that by the addition of 1.0M of sodium benzoate in seawater samples, it giving {>=} 90% efficiencies.

  11. STAINLESS STEEL INTERACTIONS WITH SALT CONTAINING PLUTONIUM OXIDES

    SciTech Connect

    Nelson, Z.; Chandler, G.; Dunn, K.; Stefek, T.; Summer, M.

    2010-02-01

    Salt containing plutonium oxide materials are treated, packaged and stored within nested, stainless steel containers based on requirements established in the DOE 3013 Standard. The moisture limit for the stored materials is less than 0.5 weight %. Surveillance activities which are conducted to assess the condition of the containers and assure continuing 3013 container integrity include the destructive examination of a select number of containers to determine whether corrosion attack has occurred as a result of stainless steel interactions with salt containing plutonium oxides. To date, some corrosion has been observed on the innermost containers, however, no corrosion has been noted on the outer containers and the integrity of the 3013 container systems is not expected to be compromised over a 50 year storage lifetime.

  12. Milling and Drilling Evaluation of Stainless Steel Powder Metallurgy Alloys

    SciTech Connect

    Lazarus, L.J.

    2001-12-10

    Near-net-shape components can be made with powder metallurgy (PM) processes. Only secondary operations such as milling and drilling are required to complete these components. In the past and currently production components are made from powder metallurgy (PM) stainless steel alloys. process engineers are unfamiliar with the difference in machining properties of wrought versus PM alloys and have had to make parts to develop the machining parameters. Design engineers are not generally aware that some PM alloy variations can be furnished with machining additives that greatly increase tool life. Specimens from a MANTEC PM alloy property study were made available. This study was undertaken to determine the machining properties of a number of stainless steel wrought and PM alloys under the same conditions so that comparisons of their machining properties could be made and relative tool life determined.

  13. Evaluation of the wear properties of high interstitial stainless steels

    SciTech Connect

    Tylczak, J.H.; Rawers, J.C.; Alman, D.E.

    2007-04-01

    Adding carbon to high nitrogen steels increases interstitial concentrations over what can be obtained with nitrogen addition alone. This can results in an increase in hardness, strength, and wear resistance. The alloys produced for this study were all based on commercially available high-nitrogen Fe-18Cr-18Mn stainless steel. This study is the first significant wear study of these new high interstitial nitrogen-carbon stainless steel alloys. Wear tests included: scratch, pin-on-disk abrasion, dry sand/rubber wheel abrasion, impeller impact, and jet erosion. Increasing interstitial concentration increased strength and hardness and improved wear resistance under all test conditions. The results are discussed in terms of overall interstitial alloy concentration.

  14. Technique to eliminate helium induced weld cracking in stainless steels

    SciTech Connect

    Chin-An Wang; Chin, B.A.; Grossbeck, M.L.

    1992-12-31

    Experiments have shown that Type 316 stainless steel is susceptible to heat-affected-zone (HAZ) cracking upon cooling when welded using the gas tungsten arc (GTA) process under lateral constraint. The cracking has been hypothesized to be caused by stress-assisted helium bubble growth and rupture at grain boundaries. This study utilized an experimental welding setup which enabled different compressive stresses to be applied to the plates during welding. Autogenous GTA welds were produced in Type 316 stainless steel doped with 256 appm helium. The application of a compressive stress, 55 Mpa, during welding suppressed the previously observed catastrophic cracking. Detailed examinations conducted after welding showed a dramatic change in helium bubble morphology. Grain boundary bubble growth along directions parallel to the weld was suppressed. Results suggest that stress-modified welding techniques may be used to suppress or eliminate helium-induced cracking during joining of irradiated materials.

  15. Lifetest investigations with stainless steel/water heat pipes

    NASA Astrophysics Data System (ADS)

    Muenzel, W. D.; Kraehling, H.

    Life tests were conducted on water heat pipes, made from four different alloys of stainless steel, at operation temperatures of 120, 160, 220, and 320 C in a reflux boiler mode for more than 20,000 hr. Other parameters varied during the tests included capillary structure, pretreatment and cleaning of the components, additional oxidation of the inner surface, filling procedures, amoung of liquid change, the number of ventings, and the duration of the reaction runs. The best results were obtained with pipes containing stainless steels with molybdenum alloy additions and with carbon contents of greater than 0.03%; with components which formed a protective surface layer; with the use of double-distilled water that had been ultrasonically degassed; with repeated ventings during the initial reaction run of 500 hr minimum duration; and with the addition of gaseous oxygen into the heat pipe during the reaction run with subsequent venting.

  16. New hermetic sealing material for vacuum brazing of stainless steels

    NASA Astrophysics Data System (ADS)

    Hildebrandt, S.; Wiehl, G.; Silze, F.

    2016-03-01

    For vacuum brazing applications such as in vacuum interrupter industry Hermetic Sealing Materials (HSM) with low partial pressure are widely used. AgCu28 dominates the hermetic sealing market, as it has a very good wetting behavior on copper and metallized ceramics. Within recent decades wetting on stainless steel has become more and more important. However, today the silver content of HSMs is more in focus than in the past decades, because it has the biggest impact on the material prices. Umicore Technical Materials has developed a new copper based HSM, CuAg40Ga10. The wettability on stainless steel is significantly improved compared to AgCu28 and the total silver content is reduced by almost 44%. In this article the physical properties of the alloy and its brazed joints will be presented compared to AgCu28.

  17. Electrochemical Corrosion Testing of Borated Stainless Steel Alloys

    SciTech Connect

    lister, tedd e; Mizia, Ronald E

    2007-05-01

    The Department of Energy Office of Civilian Radioactive Waste Management has specified borated stainless steel manufactured to the requirements of ASTM A 887-89, Grade A, UNS S30464, to be the material used for the fabrication of the fuel basket internals of the preliminary transportation, aging, and disposal canister system preliminary design. The long-term corrosion resistance performance of this class of borated materials must be verified when exposed to expected YMP repository conditions after a waste package breach. Electrochemical corrosion tests were performed on crevice corrosion coupons of Type 304 B4 and Type 304 B5 borated stainless steels exposed to single postulated in-package chemistry at 60°C. The results show low corrosion rates for the test period

  18. Electrochemical Corrosion Testing of Borated Stainless Steel Alloys

    SciTech Connect

    lister, tedd e; Mizia, Ronald E

    2007-09-01

    The Department of Energy Office of Civilian Radioactive Waste Management has specified borated stainless steel manufactured to the requirements of ASTM A 887-89, Grade A, UNS S30464, to be the material used for the fabrication of the fuel basket internals of the preliminary transportation, aging, and disposal canister system preliminary design. The long-term corrosion resistance performance of this class of borated materials must be verified when exposed to expected YMP repository conditions after a waste package breach. Electrochemical corrosion tests were performed on crevice corrosion coupons of Type 304 B4 and Type 304 B5 borated stainless steels exposed to single postulated in-package chemistry at 60°C. The results show low corrosion rates for the test period

  19. Glow discharge cleaning of carbon fiber composite and stainless steel

    NASA Astrophysics Data System (ADS)

    Airapetov, A.; Begrambekov, L.; Brémond, S.; Douai, D.; Kuzmin, A.; Sadovsky, Ya.; Shigin, P.; Vergasov, S.

    2011-08-01

    The paper experimentally investigates and analyses the features and mechanisms of both of oxygen removal by deuterium glow discharge from CFC, pyrolytic graphite and stainless steel subjected to irradiation in oxygen contaminated plasma. It is shown that oxygen implanted in pyrolytic graphite (PG) perpendicular to basal plates is removed after sputtering the layer slightly thicker than oxygen stopping zone (≈2 nm). Fast deuterium ions penetrating into CFC during GDC transfer the trapped oxygen atoms into the bulk. Thus, much thicker surface layer has to be removed (500-1000 nm) for oxygen release. Irradiation of stainless steel in plasma leads to formation of a barrier layer with thickness (2-4 nm) equal, or slightly higher than stopping range of oxygen ions. The layer accumulates the main fraction of implanted oxygen and prevents its penetration into the bulk. After barrier layer sputtering oxygen spreads into the bulk. Parameters and conditions of optimum GDC are discussed.

  20. The technology of chromium oxide passivation on stainless steel surface

    SciTech Connect

    Ohmi, Tadahiro; Ohki, Atsushi; Nakamura, Masakazu; Kawada, Koji; Watanabe, Tsuyoshi; Nakagawa, Yoshinori; Miyoshi, Shinji; Takahashi, Shinji; Chen, M.S.K. . Dept. of Electronics)

    1993-06-01

    A complete chromium oxide (Cr[sub 2]O[sub 3]) passivation technology has been developed for stainless steel surfaces for use in high purity gas-delivery systems and process chambers. Starting with an electrochemical buffing (ECB) to add to electro-polished (EP) SUS316L stainless steel material, an optimal thermal treatment was found by using a gas mixture of 10% hydrogen, 1--10 ppm oxygen and argon balance gas at 500C for 1 h. Five-day corrosion tests with HCl gas (containing 1.4 ppm moisture) at 5 kg/cm[sup 2] and 100C showed no sign of corrosion on the chromium oxide passivated surface. Chemical stability tests on this surface with silane specialty gas thermal decomposition also showed a remarkable noncatalytic activity compared with conventional surfaces.