Science.gov

Sample records for 133xe clearance curve

  1. Prospective use of xenon /sup 133/Xe clearance for amputation level selection

    SciTech Connect

    Moore, W.S.; Henry, R.E.; Malone, J.M.; Daly, M.J.; Patton, D.; Childers, S.J.

    1981-01-01

    Xenon /sup 133/Xe clearance was used to select the most distal amputation level that would allow sufficient blood flow for healing. Capillary blood flow was first measured at the most distal potential amputation level, then at successive proximal levels until an amputation site was found that had a capillary skin blood flow rate greater than or equal to 2.6 mL/min/100 g of tissue. Xenon /sup 133/Xe in saline was injected intracutaneously at each level, and flow rates were determined using a gamma camera interfaced with a computer system programmed for the Ketty-Schmidt formula modified for capillary blood flow. There were 45 cases, including one toes, six transmetatarsal, five Syme's, 25 below-knee, four knee disarticulation, three above-knee, and one hip disarticulation amputation. All amputations in patients with flow rates exceeding 2.4 mL/min/100 g of tissue healed, with two exceptions.

  2. Measurement of blood flow by the 133Xe clearance technique to grafts of amnion used in vestibuloplasty.

    PubMed

    Güler, R; Ercan, M T; Ulutunçel, N; Devrim, H; Uran, N

    1997-08-01

    The purpose of this study was to determine the blood supply to lyophilized amniotic membranes when used as graft material in vestibuloplasties. 133Xe clearance technique was used to measure the blood flow to the grafts. A total of 20 patients had either Clark (10) or Kazanjian (10) vestibuloplasties. The blood flow was determined at 2-3 days preoperatively and at 10 and 30 days postoperatively. The preoperative mandibular anterior alveolar mucosal blood flow was 34.4 +/- 10.7 and 23.1 +/- 13.1 ml/100 g/min for the Clark and Kazanjian groups, respectively. Ten days after vestibuloplasty operation with lyophilized amniotic membrane graft application the blood flow to the graft increased to 56.8 +/- 45.4 and 62.6 +/- 30.4 ml/100 g/min for the Clark and Kazanjian groups, respectively. The corresponding values at 30 days postoperatively were 24.6 +/- 10.2 and 22.2 +/- 9.2 ml/100 g/min, indicating the return to normal levels. The changes in blood flow as a function of time were statistically significant in each group (P<0.05). Our results demonstrated the angiogenic effect of lyophilized amniotic membranes until mucoid degeneration after 10-15 days.

  3. Penile xenon (/sup 133/Xe) washout: a rapid method of screening for vasculogenic impotence

    SciTech Connect

    Nseyo, U.O.; Wilbur, H.J.; Kang, S.A.; Flesh, L.; Bennett, A.H.

    1984-01-01

    The radioactive inert gas xenon (/sup 133/Xe) is a well-established isotopic indicator used to assess vascular status in many organ systems. Xenon-133 was used to evaluate male impotence. Xenon-133 was injected subcutaneously at the level of the coronal sulcus in the detumescent state. Using the gamma camera, sequential images were obtained and computer-generated curves calculated. The clearance time for 50 per cent washout of the injected /sup 133/Xe (T1/2) was then calculated for each patient, as well as a control group. Preliminary findings indicate a correlation with such established techniques of evaluating erectile impotence as history, physical examination, penile pulse Doppler tracings, and brachial-penile blood pressure index. The xenon-133 washout study was a rapid, minimally invasive, reproducible, and cost-effective method of screening those impotent patients for vasculogenic etiology of their erectile impotence. We recommend the addition of this method to the surgeon engaged in the care of impotent males.

  4. Cerebral effects of scalp cooling and extracerebral contribution to calculated blood flow values using the intravenous 133Xe technique.

    PubMed

    Friberg, L; Kastrup, J; Hansen, M; Bülow, J

    1986-06-01

    With the intravenous 133Xe technique we measured cerebral blood flow (CBF) in eight healthy subjects during normal subcutaneous temperatures and during extracranial cooling. This gave rise to the possibility of evaluating the contribution of the extracerebral blood flow to the calculation of CBF values. With a two-compartmental analysis of the wash-out curves during cooling there was a significant reduction of the CBF indices f1, representing mainly fast blood flow in the grey matter and f2, representing blood flow in the slowly perfused white matter and extracerebral structures. The reduction of f1 was due to the 'slippage' phenomenon:calculation of f1 was affected by a reduction in f2 due to a considerably reduced extracerebral blood flow. The initial slope index (ISI) calculated from 30 to 90 s of the first part of the presumed mono-exponential 133Xe wash-out curve was not affected by slippage as the ISI remained unchanged in spite of reduced extracerebral blood flow. It is concluded that CBF was unaffected by extracranial cooling. Extracranial cooling can be used to reduce the extracerebral blood flow contribution to the calculated CBF values.

  5. Detection of (133)Xe from the Fukushima nuclear power plant in the upper troposphere above Germany.

    PubMed

    Simgen, Hardy; Arnold, Frank; Aufmhoff, Heinfried; Baumann, Robert; Kaether, Florian; Lindemann, Sebastian; Rauch, Ludwig; Schlager, Hans; Schlosser, Clemens; Schumann, Ulrich

    2014-06-01

    After the accident in the Japanese Fukushima Dai-ichi nuclear power plant in March 2011 large amounts of radioactivity were released and distributed in the atmosphere. Among them were also radioactive noble gas isotopes which can be used as tracers to test global atmospheric circulation models. This work presents unique measurements of the radionuclide (133)Xe from Fukushima in the upper troposphere above Germany. The measurements involve air sampling in a research jet aircraft followed by chromatographic xenon extraction and ultra-low background gas counting with miniaturized proportional counters. With this technique a detection limit of the order of 100 (133)Xe atoms in liter-scale air samples (corresponding to about 100 mBq/m(3)) is achievable. Our results provide proof that the (133)Xe-rich ground level air layer from Fukushima was lifted up to the tropopause and distributed hemispherically. Moreover, comparisons with ground level air measurements indicate that the arrival of the radioactive plume at high altitude over Germany occurred several days before the ground level plume.

  6. Relationship of 133Xe cerebral blood flow to middle cerebral arterial flow velocity in men at rest

    NASA Technical Reports Server (NTRS)

    Clark, J. M.; Skolnick, B. E.; Gelfand, R.; Farber, R. E.; Stierheim, M.; Stevens, W. C.; Beck, G. Jr; Lambertsen, C. J.

    1996-01-01

    Cerebral blood flow (CBF) was measured by 133Xe clearance simultaneously with the velocity of blood flow through the left middle cerebral artery (MCA) over a wide range of arterial PCO2 in eight normal men. Average arterial PCO2, which was varied by giving 4% and 6% CO2 in O2 and by controlled hyperventilation on O2, ranged from 25.3 to 49.9 mm Hg. Corresponding average values of global CBF15 were 27.2 and 65.0 ml 100 g min-1, respectively, whereas MCA blood-flow velocity ranged from 42.8 to 94.2 cm/s. The relationship of CBF to MCA blood-flow velocity over the imposed range of arterial PCO2 was described analytically by a parabola with the equation: CBF = 22.8 - 0.17 x velocity + 0.006 x velocity2 The observed data indicate that MCA blood-flow velocity is a useful index of CBF response to change in arterial PCO2 during O2 breathing at rest. With respect to baseline values measured while breathing 100% O2 spontaneously, percent changes in velocity were significantly smaller than corresponding percent changes in CBF at increased levels of arterial PCO2 and larger than CBF changes at the lower arterial PCO2. These observed relative changes are consistent with MCA vasodilation at the site of measurement during exposure to progressive hypercapnia and also during extreme hyperventilation hypocapnia.

  7. Atmospheric transport modelling of time resolved 133Xe emissions from the isotope production facility ANSTO, Australia.

    PubMed

    Schöppner, M; Plastino, W; Hermanspahn, N; Hoffmann, E; Kalinowski, M; Orr, B; Tinker, R

    2013-12-01

    The verification of the Comprehensive Nuclear-Test Ban Treaty (CTBT) relies amongst other things on the continuous and worldwide monitoring of radioxenon. The characterization of the existing and legitimate background, which is produced mainly by nuclear power plants and isotope production facilities, is of high interest to improve the capabilities of the monitoring network. However, the emissions from legitimate sources can usually only be estimated. For this paper historic source terms of (133)Xe emissions from the isotope production facility at ANSTO, Sydney, Australia, have been made available in a daily resolution. Based on these high resolution data, different source term sets with weekly, monthly and yearly time resolution have been compiled. These different sets are then applied together with atmospheric transport modelling (ATM) to predict the concentration time series at two radioxenon monitoring stations. The results are compared with each other in order to examine the improvement of the prediction capability depending on the used time resolution of the most dominant source term in the region.

  8. Cerebral hemodynamics in normal-pressure hydrocephalus. Evaluation by 133Xe inhalation method and dynamic CT study

    SciTech Connect

    Tamaki, N.; Kusunoki, T.; Wakabayashi, T.; Matsumoto, S.

    1984-09-01

    Cerebral hemodynamics in 31 patients with suspected normal-pressure hydrocephalus were studied by means of the xenon-133 (133Xe) inhalation method and on dynamic computerized tomography (CT) scanning. Cerebral blood flow (CBF) is reduced in all patients with dementia. Hypoperfusion was noted in a frontal distribution in these patients compared with normal individuals. There was no difference in CBF patterns between patients with good and those with poor outcome. The CBF was increased following cerebrospinal fluid (CSF) shunting in patients who responded to that procedure: increase in flow correlated with clinical improvement, frontal and temporal lobe CBF was most markedly increased, and the CBF pattern became normal. In contrast, CBF was decreased after shunt placement in patients who were considered to have suffered from degenerative dementia, as evidenced by non-response to shunting. Dynamic computerized tomography studies demonstrated that patients with a good outcome showed a postoperative reduction in mean transit time of contrast material, most prominent in the frontal and temporal gray matter, and slight in the deep frontal structures, but not in the major cerebral vessels. Patients with poor outcome after shunting, however, had an increase in transit time in all regions. This corresponded well with the results as determined by the 133Xe inhalation method.

  9. Cerebral blood flow in the newborn infant: comparison of Doppler ultrasound and /sup 133/xenon clearance

    SciTech Connect

    Greisen, G.; Johansen, K.; Ellison, P.H.; Fredriksen, P.S.; Mali, J.; Friis-Hansen, B.

    1984-03-01

    Two techniques of Doppler ultrasound examination, continuous-wave and range-gated, applied to the anterior cerebral artery and to the internal carotid artery, were compared with /sup 133/xenon clearance after intravenous injection. Thirty-two sets of measurements were obtained in 16 newborn infants. The pulsatility index, the mean flow velocity, and the end-diastolic flow velocity were read from the Doppler recordings. Mean cerebral blood flow was estimated from the /sup 133/Xe clearance curves. The correlation coefficients between the Doppler and the /sup 133/Xe measurements ranged from 0.41 to 0.82. In the subset of 16 first measurements in each infant, there were no statistically significant differences between the correlation coefficients of the various Doppler ultrasound variables, but the correlation coefficients were consistently lower for the pulsatility index than for mean flow velocity or end-diastolic flow velocity, and they were consistently higher for the range-gated than for the continuous-wave Doppler technique.

  10. Effects of selected materials and geometries on the beta dose equivalent rate in a tissue equivalent phantom immersed in infinite clouds of 133Xe.

    PubMed

    Piltingsrud, H V; Gels, G L

    1986-06-01

    Most calculations of dose equivalent (D.E.) rates at 70-micron tissue depths in tissue equivalent (T.E.) phantoms from infinite clouds (radius exceeds maximum beta range in air) of 133Xe do not consider the possible effects of clothing overlays. Consequently, a series of measurements were made using a 1-mm-thick plastic scintillation detector assembly mounted in a tissue equivalent (T.E.) phantom with an overlay of 70 micron of T.E. material. This assembly was placed in an infinite cloud containing a known concentration of 133Xe. Material samples were placed at selected distances from the detector phantom, both individually and in various combinations. Pulse-height spectra resulting from beta radiations were converted to relative D.E. rates at a 70-micron tissue depth. The relative D.E. rates were reduced from values with no clothing cover by as little as 45% when placing a single thin nylon cloth 1 cm from the phantom, to 94% for a T-shirt material plus wool material plus denim placed 1/2, 1 and 3 cm, respectively, from the phantom. The results indicate that even loosely fitting clothing can have an important effect on reducing the D.E. rate. Close-fitting clothing appears to provide better protection.

  11. Crossed cerebellar diaschisis in ischemic stroke: a study of regional cerebral blood flow by /sup 133/Xe inhalation and single photon emission computerized tomography

    SciTech Connect

    Meneghetti, G.; Vorstrup, S.; Mickey, B.; Lindewald, H.; Lassen, N.A.

    1984-06-01

    Seventy measurements of CBF were performed in 12 stroke patients by /sup 133/Xe inhalation and a rapidly rotating single photon emission computerized tomograph. CBF was measured every other day during the acute phase and at 2- and 6-month follow-up visits. A persistent contralateral cerebellar blood flow depression was evident in five patients with severe hemispheric low flow areas, which correlated with large, hypodense lesions on the computerized tomographic scan. In a sixth patient with a small, deep infarct, a transient crossed cerebellar low flow was observed, while the clinical symptoms persisted. It is concluded from this serial study that crossed cerebellar diaschisis is a common finding in completed stroke. It is probably caused by disconnection of the corticopontine pathways, a disconnection that tends to persist. The phenomenon is in fact less variable than the stroke-related CBF changes in the infarcted hemisphere, in which a period of relative hyperemia is frequently seen.

  12. Free water clearance curves during saline, mannitol, glucose and urea diuresis in the rat

    PubMed Central

    Martinez-Maldonado, Manuel; Opava-Stitzer, Susan

    1978-01-01

    1. Free water clearances were measured during infusion of hypotonic saline, glucose, urea, and mannitol in Brattleboro rats. For each solute the free water clearances were plotted using either V or (CH2O + CNa) as the distal tubular delivery term. 2. In all cases the use of (CH2O + CNa) as distal delivery term yielded a steeper relationship than when V was used. There were no significant differences in the CH2O to V relationship when saline, glucose and mannitol was the solute infused. Urea, however, resulted in a curve with a slope significantly less than that for the other solutes. 3. When CH2O was plotted against (CH2O + CNa) there was still no significant difference between the slopes of the curves during saline or mannitol infusion. Use of this delivery term, however, resulted in a slope during glucose infusion which was significantly greater than that during saline or mannitol infusion. The slope for urea infusion remained lower than that for any other solute. 4. Regardless of the delivery term used, there was no significant difference in the slopes of the curves for awake Wistar and awake Brattleboro rats during mannitol infusion. This indicates that the awake rat is a suitable model for free water clearance studies. 5. The results indicate that NaCl and mannitol are both adequate for free water clearance and that (CH2O + CNa) is a better index of distal delivery than V. PMID:690907

  13. Reproducibility of the /sup 133/Xe inhalation technique in resting studies: task order and sex related effects in healthy young adults

    SciTech Connect

    Warach, S.; Gur, R.C.; Gur, R.E.; Skolnick, B.E.; Obrist, W.D.; Reivich, M.

    1987-12-01

    Repeated applications of the /sup 133/Xe inhalation technique for measuring regional CBF (rCBF) were made during consecutive resting conditions in a sample of young healthy subjects. Subjects were grouped by order and by sex (nine had resting studies as the initial two measurements in a series of four measurement (six men, three women) and six had these measurements later (two men, four women)). Three flow parameters were examined: f1 (fast flow) and IS (initial slope) for gray matter CBF, and CBF-15 for mean CBF (gray and white matter over 15-min integration), as well as w1, the percentage of tissue with fast clearing characteristics. With all groups combined, there were no significant differences between the two resting measurements, and high test-retest correlations were obtained for the flow parameters and w1. Analyses by order and sex grouping revealed, for the flow parameters, significant interactions of test-retest difference with order. Repeated initial studies showed reduced CBF from the first to second measurement, whereas resting studies performed later in the series showed no reduction. Interactions for test-retest difference with sex indicated that reduced CBF in serial measures was more pronounced for women. No hemispheric or regional specificity to account for these effects was found. Correction for PaCO/sub 2/ differences did not alter these results. The results resemble data regarding habituation effects measured for other psychophysiologic measures, and suggest that reduction in CBF for consecutive measurements made on the same day may reflect habituation. This underscores the importance of controlling for effects of habituation on serial measurements of CBF and metabolism.

  14. Correlation of elimination fraction area under the curve with total body clearance.

    PubMed

    Grabowski, Tomasz; Raczyńska-Pawelec, Anna; Starościak, Marcin; Jaroszewski, Jerzy Jan

    2016-02-01

    This study attempted to determine the area under the curve ([Formula: see text]), which corresponds to the sum of all elimination processes correlated with the total clearance value. The study attempted to determine the [Formula: see text] based on the coordinates known from classic non-compartmental pharmacokinetics for a single administration of the drug. 318 pharmacokinetics profiles were used for the analysis, obtained from 220 healthy subjects over ten studies. Pharmacokinetic calculations were performed with the use of Phoenix™ WinNonlin(®) 6.3. The leave-one-out (LOO) method was used for model cross-validation. Squared cross-validated correlation coefficient (Q (2)) parameter and the difference between Q (2) and R (2) were calculated as a measure of the internal performance and model predictive ability. A high correlation between the clearance value and [Formula: see text] was demonstrated (R (2) > 0.65). However, only in the case of four studies was it possible to validate the linear model using the leave-one-out validation procedure (R (2) > 0.86). The present study proposed a method of graphical and mathematical determination of the area under the curve for the drug elimination process after a single dose of the drug. Furthermore, the concept of calculating the statistical moments and mean elimination time (MET) only for elimination processes based on [Formula: see text] was presented. The result of this work is also a new method of determining the half-life of elimination phase based on the MET value.

  15. Blood flow in exercising muscles by xenon clearance and by microsphere trapping

    SciTech Connect

    Cerretelli, P.; Marconi, C.; Pendergast, D.; Meyer, M.; Heisler, N.; Piiper, J.

    1984-01-01

    The accuracy of muscle blood flow measurement by the /sup 133/Xe clearance method (Qxe) was assessed against direct venous outflow (Qv) and microsphere trapping flow (Q..mu..) determinations in isolated perfused dog gastrocnemius both at rest and during graded stimulation (O/sub 2/ consumption (Vo/sub 2/) up to 12 ml x 100 g/sup -1/ x min/sup -1/) and in the gastrocnemius, vastus lateralis, and triceps of intact dogs at rest and while running on a treadmill at varied speeds up to maximum Vo/sub 2/. In 29 measurements performed in 11 isolated muscles, Q..mu.. was in good agreement with Qv at rest and at all stimulation levels (Q..mu../Qv = 1.0 r = 0.98). /sup 133/Xe clearance yielded much lower blood flows than the venous outflow and the microsphere trapping methods. In 43 measurements in 11 muscles, the mean Qxe/Qv ratio was 0.57 +/- 0.03 (SE), independent of blood flow. Similarly, in 65 measurements in 2 intact dogs, the mean Qxe/Q..mu.. ratio in all tested muscles was 0.49 +/- 0.02 (SE), independent of blood flow. These results show that the /sup 133/Xe clearance method considerably underestimates blood flow in dog muscles.

  16. Computation and Analysis of the Global Distribution of the Radioxenon Isotope 133Xe based on Emissions from Nuclear Power Plants and Radioisotope Production Facilities and its Relevance for the Verification of the Nuclear-Test-Ban Treaty

    NASA Astrophysics Data System (ADS)

    Wotawa, Gerhard; Becker, Andreas; Kalinowski, Martin; Saey, Paul; Tuma, Matthias; Zähringer, Matthias

    2010-05-01

    Monitoring of radioactive noble gases, in particular xenon isotopes, is a crucial element of the verification of the Comprehensive Nuclear-Test-Ban Treaty (CTBT). The capability of the noble gas network, which is currently under construction, to detect signals from a nuclear explosion critically depends on the background created by other sources. Therefore, the global distribution of these isotopes based on emissions and transport patterns needs to be understood. A significant xenon background exists in the reactor regions of North America, Europe and Asia. An emission inventory of the four relevant xenon isotopes has recently been created, which specifies source terms for each power plant. As the major emitters of xenon isotopes worldwide, a few medical radioisotope production facilities have been recently identified, in particular the facilities in Chalk River (Canada), Fleurus (Belgium), Pelindaba (South Africa) and Petten (Netherlands). Emissions from these sites are expected to exceed those of the other sources by orders of magnitude. In this study, emphasis is put on 133Xe, which is the most prevalent xenon isotope. First, based on the emissions known, the resulting 133Xe concentration levels at all noble gas stations of the final CTBT verification network were calculated and found to be consistent with observations. Second, it turned out that emissions from the radioisotope facilities can explain a number of observed peaks, meaning that atmospheric transport modelling is an important tool for the categorization of measurements. Third, it became evident that Nuclear Power Plant emissions are more difficult to treat in the models, since their temporal variation is high and not generally reported. Fourth, there are indications that the assumed annual emissions may be underestimated by factors of two to ten, while the general emission patterns seem to be well understood. Finally, it became evident that 133Xe sources mainly influence the sensitivity of the

  17. An evaluation of the external radiation exposure dosimetry and calculation of maximum permissible concentration values for airborne materials containing 18F, 15O, 13N, 11C and 133Xe.

    PubMed

    Piltingsrud, H V; Gels, G L

    1985-11-01

    To better understand the dose equivalent (D.E.) rates produced by airborne releases of gaseous positron-emitting radionuclides under various conditions of cloud size, a study of the external radiation exposure dosimetry of these radionuclides, as well as negatron, gamma and x-ray emitting 133Xe, was undertaken. This included a calculation of the contributions to D.E. as a function of cloud radii, at tissue depths of 0.07 mm (skin), 3 mm (lens of eye) and 10 mm (whole body) from both the particulate and photon radiations emitted by these radionuclides. Estimates of maximum permissible concentration (MPC) values were also calculated based on the calculated D.E. rates and current regulations for personnel radiation protection (CFR84). Three continuous air monitors, designed for use with 133Xe, were evaluated for applications in monitoring air concentrations of the selected positron emitters. The results indicate that for a given radionuclide and for a cloud greater than a certain radius, personnel radiation dosimeters must respond acceptably to only the photon radiations emitted by the radionuclide to provide acceptable personnel dosimetry. For clouds under that radius, personnel radiation dosimeters must also respond acceptably to the positron or negatron radiations to provide acceptable personnel dosimetry. It was found that two out of the three air concentration monitors may be useful for monitoring air concentrations of the selected positron emitters.

  18. Effect of hematocrit and systolic blood pressure on cerebral blood flow in newborn infants

    SciTech Connect

    Younkin, D.P.; Reivich, M.; Jaggi, J.L.; Obrist, W.D.; Delivoria-Papadopoulos, M.

    1987-06-01

    The effects of hematocrit and systolic blood pressure on cerebral blood flow were measured in 15 stable, low birth weight babies. CBF was measured with a modification of the xenon-133 (/sup 133/Xe) clearance technique, which uses an intravenous bolus of /sup 133/Xe, an external chest detector to estimate arterial /sup 133/Xe concentration, eight external cranial detectors to measure cephalic /sup 133/Xe clearance curves, and a two-compartmental analysis of the cephalic /sup 133/Xe clearance curves to estimate CBF. There was a significant inverse correlation between hematocrit and CBF, presumably due to alterations in arterial oxygen content and blood viscosity. Newborn CBF varied independently of systolic blood pressure between 60 and 84 mm Hg, suggesting an intact cerebrovascular autoregulatory mechanism. These results indicate that at least two of the factors that affect newborn animal CBF are operational in human newborns and may have important clinical implications.

  19. Serum Human Chorionic Gonadotropin (β- hCG) Clearance Curves in Women with Successfully Expectantly Managed Tubal Ectopic Pregnancies: A Retrospective Cohort Study

    PubMed Central

    Helmy, Samir; Mavrelos, Dimitrios; Sawyer, Elinor; Ben-Nagi, Jara; Koch, Marianne; Day, Andrea; Jurkovic, Davor

    2015-01-01

    Objective To establish clearance curves for serum β -hCG in women with successfully expectantly managed tubal ectopic pregnancies. Design Retrospective cohort study. Non- viable tubal ectopic pregnancy was diagnosed on transvaginal ultrasound. If initial serum β hCG was less than 5000 IU/L and patients were asymptomatic, expectant management was offered. Patients underwent serial β hCG measurements until serum β hCG was less than 20 IU/l, or the urine pregnancy test was negative. Setting Early Pregnancy and Gynaecology Assessment Unit, Kings College Hospital, London (December 1998 to July 2006). Patients We included 161 women with diagnosed non-viable tubal ectopic pregnancy who underwent successful expectant management. Main outcome measure Serum β hCG level. Results Mean initial serum β- hCG was 488 IU/L (41 - 4883) and median serum β hCG clearance time was 19 days (5 - 82). The average half-life of β hCG clearance was 82.5 hours (±SD 50.2) in patients with steadily declining serum β- hCG levels compared to 106.7 hours (±SD 72.0) in patients with primarily plateauing β-hCG levels in the declining phase. However, these differences were not significant (p>0.05). Conclusion We identified a median follow-up of 19 days until serum β hCG clearance in women with tubal ectopic pregnancy and successful expectant management. Although non- significant, women with initially plateauing serum β hCG showed a longer follow-up time until clearance compared to women with steadily declining β hCG levels. This information may serve as a guideline enabling clinicians to predict the length of follow-up for women with tubal ectopic pregnancy and expectant management. PMID:26135923

  20. Hemodynamics of erection in man

    SciTech Connect

    Shirai, M.; Ishii, N.

    1981-02-01

    Inquiry was made into the theory that closure of the efferent vein from the corpora cavernosa is essential for erection of the human penis. To determine whether the venous closure is indeed a prerequisite to human penile erection, two tests were carried out in men: (1) direct infusion in 133Xe into corpora cavernosa and (2) performance of carvernosography. In each case, penile erection was induced by providing the subject with sexual stimulation. The behavioral changes were studied through the 133Xe clearance curve and the contrast medium, respectively. When the penis remained flaccid, the 133Xe clearance curve followed a gentle path and the contrast medium could be noted within the penis for a relatively long period. However, on erection with sexual stimulation, the 133Xe clearance curve fell rapidly instead of following the gentle course expected in the case of venous closure. Also, the contrast medium quickly flowed out of the corpora cavernosa. The human penis therefore can well erect without closure of the efferent vein from the corpora cavernosa.

  1. Effect of Internal Clearance on Load Distribution and Life of Radially Loaded Ball and Roller Bearings

    NASA Technical Reports Server (NTRS)

    Oswald, Fred B.; Zaretsky, Erwin V.; Poplawski, Joseph V.

    2012-01-01

    The effect of internal clearance on radially loaded deepgroove ball and cylindrical roller bearing load distribution and fatigue life was determined for four clearance groups defined in the bearing standards. The analysis was extended to negative clearance (interference) conditions to produce a curve of life factor versus internal clearance. Rolling-element loads can be optimized and bearing life maximized for a small negative operating clearance. Life declines gradually with positive clearance and rapidly with increasing negative clearance. Relationships were found between bearing life and internal clearance as a function of ball or roller diameter, adjusted for load. Results are presented as life factors for radially loaded bearings independent of bearing size or applied load. In addition, a modified Stribeck Equation is presented that relates the maximum rolling-element load to internal bearing clearance.

  2. Malaria parasite clearance.

    PubMed

    White, Nicholas J

    2017-02-23

    Following anti-malarial drug treatment asexual malaria parasite killing and clearance appear to be first order processes. Damaged malaria parasites in circulating erythrocytes are removed from the circulation mainly by the spleen. Splenic clearance functions increase markedly in acute malaria. Either the entire infected erythrocytes are removed because of their reduced deformability or increased antibody binding or, for the artemisinins which act on young ring stage parasites, splenic pitting of drug-damaged parasites is an important mechanism of clearance. The once-infected erythrocytes returned to the circulation have shortened survival. This contributes to post-artesunate haemolysis that may follow recovery in non-immune hyperparasitaemic patients. As the parasites mature Plasmodium vivax-infected erythrocytes become more deformable, whereas Plasmodium falciparum-infected erythrocytes become less deformable, but they escape splenic filtration by sequestering in venules and capillaries. Sequestered parasites are killed in situ by anti-malarial drugs and then disintegrate to be cleared by phagocytic leukocytes. After treatment with artemisinin derivatives some asexual parasites become temporarily dormant within their infected erythrocytes, and these may regrow after anti-malarial drug concentrations decline. Artemisinin resistance in P. falciparum reflects reduced ring stage susceptibility and manifests as slow parasite clearance. This is best assessed from the slope of the log-linear phase of parasitaemia reduction and is commonly measured as a parasite clearance half-life. Pharmacokinetic-pharmacodynamic modelling of anti-malarial drug effects on parasite clearance has proved useful in predicting therapeutic responses and in dose-optimization.

  3. Cimetidine impairs nitrazepam clearance.

    PubMed

    Ochs, H R; Greenblatt, D J; Gugler, R; Müntefering, G; Locniskar, A; Abernethy, D R

    1983-08-01

    The effect of cimetidine on hepatic clearance of the benzodiazepine derivative nitrazepam was evaluated in healthy subjects. Six received a single 5- or 10-mg oral nitrazepam dose in the drug-free state and again with therapeutic cimetidine doses. Nitrazepam kinetics were determined from multiple serum concentrations measured during the 72 hr after each dose. Cimetidine had no effect on nitrazepam absorption kinetics, since peak serum nitrazepam concentration and time of peak concentration were not altered. Cimetidine did not alter nitrazepam volume of distribution, but cimetidine consistently reduced nitrazepam clearance, from a mean of 1.41 ml/min/kg in the control state to 1.17 ml/min/kg during cimetidine treatment. This resulted in prolongation of nitrazepam elimination t1/2 from 22.2 to 27.8 hr. Thus the ability of cimetidine to impair drug oxidation in man extends to the capacity for clearance of nitrazepam, a compound biotransformed mainly by nitroreduction.

  4. CSF clearance in Alzheimer Disease measured with dynamic PET.

    PubMed

    de Leon, Mony J; Li, Yi; Okamura, Nobuyuki; Tsui, Wai H; Saint Louis, Les A; Glodzik, Lidia; Osorio, Ricardo S; Fortea, Juan; Butler, Tracy; Pirraglia, Elizabeth; Fossati, Silvia; Kim, Hee-Jin; Carare, Roxana O; Nedergaard, Maiken; Benveniste, Helene; Rusinek, Henry

    2017-03-16

    Evidence supporting the hypothesis that reduced cerebrospinal fluid (CSF) clearance is involved in the pathophysiology of Alzheimer's disease (AD) comes from primarily from rodent models. However, unlike rodents where predominant extra-cranial CSF egress is via olfactory nerves traversing the cribriform plate, human CSF clearance pathways are not well characterized. Using dynamic Positron Emission Tomography (PET) with (18)F-THK5117 a tracer for tau pathology, the ventricular CSF time activity was used as a biomarker for CSF clearance. We tested three hypotheses: 1. Extra-cranial CSF is detected at the superior turbinates; 2. CSF clearance is reduced in AD; and 3. CSF clearance is inversely associated with amyloid deposition. Methods: 15 subjects, 8 with AD and 7 normal control volunteers were examined with (18)F-THK5117. 10 subjects additionally received (11)C-PiB PET scans and 8 were PiB positive. Ventricular time activity curves (TAC) of (18)F-THK5117 were used to identify highly correlated TAC from extra-cranial voxels. Results: For all subjects, the greatest density of CSF positive extra-cranial voxels was in the nasal turbinates. Tracer concentration analyses validated the superior nasal turbinate CSF signal intensity. AD patients showed ventricular tracer clearance reduced by 23% and 66% fewer superior turbinate CSF egress sites. Ventricular CSF clearance was inversely associated with amyloid deposition. Conclusion: The human nasal turbinate is part of the CSF clearance system. Lateral ventricle and superior nasal turbinates CSF clearance abnormalities are found in AD. Ventricular CSF clearance reductions are associated with increased brain amyloid depositions. These data suggest that PET measured CSF clearance is a biomarker of potential interest in AD and other neurodegenerative diseases.

  5. Advanced Thermal HPT Clearance Control

    NASA Technical Reports Server (NTRS)

    WojciechVoytek, Sak

    2006-01-01

    OBJECTIVE: Develop a fast acting HPT Active Clearance Control System to improve engine efficiency and reduce emissions CHALLENGE: Reduction of HPT blade clearance throughout engine operation System complexity, reliability and cost must remain comparable or surpass today s engines Reduced clearance may increase possibility of rubs

  6. Experimental and Numerical Study on Blanking Process with Negative Clearance

    NASA Astrophysics Data System (ADS)

    Hirota, Kenji; Yanaga, Hiroki; Fukushima, Katsunori

    This study summarizes the characteristics of blanking behavior with a negative clearance. Several experiments were performed for two aluminum sheets over a wide range of clearances including negative values. Blanking with negatively large clearances was found to produce fine cut edges with less roll-over and no fracture zone even for a brittle material. Corresponding simulations were performed using the Ayada's criterion for predicting ductile fracture initiation. Each zone of blanked part edges such as roll-over and fractured zone agreed well with that obtained in the experiments except a few cases accompanied by secondary shear. The reason for prevention of fracture by using negative clearances was explained with the change of the damage value during the process; the damage value was kept low throughout the blanking operation since the mean stress dominating the damage value became compressive around the die edge. Influences of blanking parameters on load-stroke curves were also investigated. The curves for negative clearances showed gradual increase in load toward the end of stroke. The earlier fracture initiated, the earlier the load reached a peak. Simulated curves showed the same tendency and in good agreement with the experimental ones quantitatively.

  7. Site clearance working group

    SciTech Connect

    1997-03-01

    The Gulf of Mexico and Louisiana continue to be areas with a high level of facility removal, and the pace of removal is projected to increase. Regulations were promulgated for the Gulf of Mexico and Louisiana requiring that abandoned sites be cleared of debris that could interfere with fishing and shrimping activities. The site clearance regulations also required verification that the sites were clear. Additionally, government programs were established to compensate fishermen for losses associated with snagging their equipment on oil and gas related objects that remained on the water bottoms in areas other than active producing sites and sites that had been verified as clear of obstructions and snags. The oil and gas industry funds the compensation programs. This paper reviews the regulations and evolving operating practices in the Gulf of Mexico and Louisiana where site clearance and fisherman`s gear compensation regulations have been in place for a number of years. Although regulations and guidelines may be in place elsewhere in the world, this paper focuses on the Gulf of Mexico and Louisiana. Workshop participants are encouraged to bring up international issues during the course of the workshop. Additionally, this paper raises questions and focuses on issues that are of concern to the various Gulf of Mexico and Louisiana water surface and water bottom stakeholders. This paper does not have answers to the questions or issues. During the workshop participants will debate the questions and issues in an attempt to develop consensus opinions and/or make suggestions that can be provided to the appropriate organizations, both private and government, for possible future research or policy adjustments. Site clearance and facility removal are different activities. Facility removal deals with removal of the structures used to produce oil and gas including platforms, wells, casing, piles, pipelines, well protection structures, etc.

  8. Turbomachinery Clearance Control

    NASA Technical Reports Server (NTRS)

    Chupp, Raymond E.; Hendricks, Robert C.; Lattime, Scott B.; Steinetz, Bruce M.; Aksit, Mahmut F.

    2007-01-01

    Controlling interface clearances is the most cost effective method of enhancing turbomachinery performance. Seals control turbomachinery leakages, coolant flows and contribute to overall system rotordynamic stability. In many instances, sealing interfaces and coatings are sacrificial, like lubricants, giving up their integrity for the benefit of the component. They are subjected to abrasion, erosion, oxidation, incursive rubs, foreign object damage (FOD) and deposits as well as extremes in thermal, mechanical, aerodynamic and impact loadings. Tribological pairing of materials control how well and how long these interfaces will be effective in controlling flow. A variety of seal types and materials are required to satisfy turbomachinery sealing demands. These seals must be properly designed to maintain the interface clearances. In some cases, this will mean machining adjacent surfaces, yet in many other applications, coatings are employed for optimum performance. Many seals are coating composites fabricated on superstructures or substrates that are coated with sacrificial materials which can be refurbished either in situ or by removal, stripping, recoating and replacing until substrate life is exceeded. For blade and knife tip sealing an important class of materials known as abradables permit blade or knife rubbing without significant damage or wear to the rotating element while maintaining an effective sealing interface. Most such tip interfaces are passive, yet some, as for the high-pressure turbine (HPT) case or shroud, are actively controlled. This work presents an overview of turbomachinery sealing. Areas covered include: characteristics of gas and steam turbine sealing applications and environments, benefits of sealing, types of standard static and dynamics seals, advanced seal designs, as well as life and limitations issues.

  9. Effect of oral N-acetylcysteine on mucus clearance.

    PubMed

    Millar, A B; Pavia, D; Agnew, J E; Lopez-Vidriero, M T; Lauque, D; Clarke, S W

    1985-07-01

    Oral N-acetylcysteine has been advocated as a mucolytic agent for use in chronic bronchitis. We have investigated the effects of regular use of this drug at a dose of 200 mg thrice daily for 4 weeks in nine patients with chronic bronchitis on lung function, lung mucociliary clearance and sputum viscosity in a controlled, double-blind, crossover study. No significant differences were found in lung function, mucociliary clearance curves or sputum viscosity following treatment with N-acetylcysteine compared to control or placebo measurements.

  10. Bradford Curves.

    ERIC Educational Resources Information Center

    Rousseau, Ronald

    1994-01-01

    Discussion of informetric distributions shows that generalized Leimkuhler functions give proper fits to a large variety of Bradford curves, including those exhibiting a Groos droop or a rising tail. The Kolmogorov-Smirnov test is used to test goodness of fit, and least-square fits are compared with Egghe's method. (Contains 53 references.) (LRW)

  11. 30 CFR 57.11010 - Stairstep clearance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Stairstep clearance. 57.11010 Section 57.11010... Escapeways Travelways-Surface and Underground § 57.11010 Stairstep clearance. Vertical clearance above stair... to indicate an impaired clearance....

  12. 30 CFR 57.11008 - Restricted clearance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Restricted clearance. 57.11008 Section 57.11008... Escapeways Travelways-Surface and Underground § 57.11008 Restricted clearance. Where restricted clearance creates a hazard to persons, the restricted clearance shall be conspicuously marked....

  13. 30 CFR 56.11010 - Stairstep clearance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Stairstep clearance. 56.11010 Section 56.11010... Stairstep clearance. Vertical clearance above stair steps shall be a minimum of seven feet, or suitable warning signs or similar devices shall be provided to indicate an impaired clearance....

  14. 28 CFR 524.74 - Activities clearance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Activities clearance. 524.74 Section 524... clearance. (a) Except as provided for in paragraph (b) of this section, the Warden is the clearance... Security cases. Central Office Inmate Monitoring Section staff shall be the clearance authority on...

  15. 30 CFR 56.11008 - Restricted clearance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Restricted clearance. 56.11008 Section 56.11008 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Restricted clearance. Where restricted clearance creates a hazard to persons, the restricted clearance...

  16. Clearance of von Willebrand factor.

    PubMed

    Denis, Cécile V; Christophe, Olivier D; Oortwijn, Beatrijs D; Lenting, Peter J

    2008-02-01

    The life cycle of von Willebrand factor (VWF) comprises a number of distinct steps, ranging from the controlled expression of the VWF gene in endothelial cells and megakaryocytes to the removal of VWF from the circulation. The various aspects of VWF clearance have been the objects of intense research in the last few years, stimulated by observations that VWF clearance is a relatively common component of the pathogenesis of type 1 von Willebrand disease (VWD). Moreover, improving the survival of VWF is now considered as a viable therapeutic strategy to prolong the half-life of factor VIII in order to optimise treatment of haemophilia A. The present review aims to provide an overview of recent findings with regard to the molecular basis of VWF clearance. A number of parameters have been identified that influence VWF clearance, including its glycosylation profile and a number of VWF missense mutations. In addition, in-vivo studies have been used to identify cells that contribute to the catabolism of VWF, providing a starting point for the identification of receptors that mediate the cellular uptake of VWF. Finally, we discuss recent data describing chemically modification of VWF as an approach to prolong the half-life of the VWF/FVIII complex.

  17. Aerial Refueling Clearance Initiation Request

    DTIC Science & Technology

    2016-07-14

    and receiver agencies. The AR Clearance Initiation Request document recognizes the requirement for definitive aerial refueling agreements between...include directions for the development or content of these contractual agreements. 15. –SUBJECT TERMS See Document Terms and Definitions , Page 8 16...7 Terms and Definitions

  18. Myeloid cell turnover and clearance

    PubMed Central

    Janssen, William J.; Bratton, Donna L.; Jakubzick, Claudia V.; Henson, Peter M.

    2016-01-01

    Given the dual and intrinsically contradictory roles for myeloid cells in both protective and yet also damaging effects of inflammatory and immunological processes we suggest that it is important to consider the mechanisms and circumstances by which these cells are removed, either in the normal unchallenged state or during inflammation or disease. In this essay we address these subjects from a conceptual perspective, focusing as examples on four main myeloid cell types (neutrophils, monocytes, macrophages and myeloid dendritic cells) and their clearance from the circulation or from naïve and inflamed tissues. While the primary clearance process appears to involve endocytic uptake into macrophages, various tissue cell types can also recognize and remove dying cells though their overall quantitative contribution is unclear. In fact, surprisingly, given the wealth of study in this area over the last 30 years, our conclusion is that we are still challenged with substantial lack of mechanistic and regulatory understanding of when, how and by what mechanisms migratory myeloid cells come to die, are recognized as needing to be removed and indeed the precise processes of uptake of either the intact or fragmented cells. This reflects the extreme complexity and inherent redundancy of the clearance processes and argues for substantial investigative effort in this arena. In addition, it leads us to a sense that approaches to significant therapeutic modulation of selective myeloid clearance is still a long way off. PMID:27837740

  19. The effects of selected air pollutants on clearance of titanic oxide particles from the lungs of rats.

    PubMed

    Ferin, J; Leach, L J

    1975-09-01

    A procedure utilizing the lung clearance kinetics of titanic oxide (TiO2) particles was used to determine the effects of inhaled sulphur dioxide (SO2) and nitrogen oxides (NO x) on particle clearance. The procedure is reproducible and mainly tests clearance mechanisms involving alveolar macrophages and the mucociliary transport system at the alveolobronchial clearance pathway. At low SO2 or NOx exposures enhanced particle clearance was observed. Lung clearance was depressed at 15 and 24 ppm of NO2 after 22 exposures as well as at 20 ppm of SO2 after 11 exposures, and also at 1 ppm of SO2 after 25 exposures. Dose-response curves for the SO2 and NOx exposures showed differences explainable by the routes by which these gases reach the alveolar macrophages.

  20. Microwave Blade Tip Clearance System: An Update

    NASA Technical Reports Server (NTRS)

    Geisheimer, Jon

    2006-01-01

    Newer engines use compressor bleed air and a model to close clearances open loop. Measuring clearances and closing the control loop can add additional efficiencies. Tip clearance control has been identified as a key technology for future engines Additional benefits in prognostics, NSMS, and condition-based maintenance. In the HPT for every 1 mil improvement in clearance: a) SFC decreases 0.1%; and b) EGT margin increases 1 C.

  1. 14 CFR 23.925 - Propeller clearance.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ..., an airplane with an aft mounted propeller must be designed such that the propeller will not contact...) Structural clearance. There must be— (1) At least one inch radial clearance between the blade tips and the... least one-half inch longitudinal clearance between the propeller blades or cuffs and stationary parts...

  2. 14 CFR 23.925 - Propeller clearance.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ..., an airplane with an aft mounted propeller must be designed such that the propeller will not contact...) Structural clearance. There must be— (1) At least one inch radial clearance between the blade tips and the... least one-half inch longitudinal clearance between the propeller blades or cuffs and stationary parts...

  3. 14 CFR 23.925 - Propeller clearance.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ..., an airplane with an aft mounted propeller must be designed such that the propeller will not contact...) Structural clearance. There must be— (1) At least one inch radial clearance between the blade tips and the... least one-half inch longitudinal clearance between the propeller blades or cuffs and stationary parts...

  4. 14 CFR 23.925 - Propeller clearance.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ..., an airplane with an aft mounted propeller must be designed such that the propeller will not contact...) Structural clearance. There must be— (1) At least one inch radial clearance between the blade tips and the... least one-half inch longitudinal clearance between the propeller blades or cuffs and stationary parts...

  5. 29 CFR 1917.113 - Clearance heights.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false Clearance heights. 1917.113 Section 1917.113 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) MARINE TERMINALS Terminal Facilities § 1917.113 Clearance heights. Clearance heights shall...

  6. 22 CFR 16.6 - Security clearances.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 22 Foreign Relations 1 2013-04-01 2013-04-01 false Security clearances. 16.6 Section 16.6 Foreign Relations DEPARTMENT OF STATE PERSONNEL FOREIGN SERVICE GRIEVANCE SYSTEM § 16.6 Security clearances. The agencies shall use their best endeavors to expedite security clearances whenever necessary to ensure a...

  7. 22 CFR 16.6 - Security clearances.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 22 Foreign Relations 1 2014-04-01 2014-04-01 false Security clearances. 16.6 Section 16.6 Foreign Relations DEPARTMENT OF STATE PERSONNEL FOREIGN SERVICE GRIEVANCE SYSTEM § 16.6 Security clearances. The agencies shall use their best endeavors to expedite security clearances whenever necessary to ensure a...

  8. 22 CFR 16.6 - Security clearances.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 22 Foreign Relations 1 2011-04-01 2011-04-01 false Security clearances. 16.6 Section 16.6 Foreign Relations DEPARTMENT OF STATE PERSONNEL FOREIGN SERVICE GRIEVANCE SYSTEM § 16.6 Security clearances. The agencies shall use their best endeavors to expedite security clearances whenever necessary to ensure a...

  9. 22 CFR 16.6 - Security clearances.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Security clearances. 16.6 Section 16.6 Foreign Relations DEPARTMENT OF STATE PERSONNEL FOREIGN SERVICE GRIEVANCE SYSTEM § 16.6 Security clearances. The agencies shall use their best endeavors to expedite security clearances whenever necessary to ensure a...

  10. 30 CFR 18.24 - Electrical clearances.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Electrical clearances. 18.24 Section 18.24... APPROVAL OF MINING PRODUCTS ELECTRIC MOTOR-DRIVEN MINE EQUIPMENT AND ACCESSORIES Construction and Design Requirements § 18.24 Electrical clearances. Minimum clearances between uninsulated electrical...

  11. 30 CFR 18.24 - Electrical clearances.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Electrical clearances. 18.24 Section 18.24... APPROVAL OF MINING PRODUCTS ELECTRIC MOTOR-DRIVEN MINE EQUIPMENT AND ACCESSORIES Construction and Design Requirements § 18.24 Electrical clearances. Minimum clearances between uninsulated electrical...

  12. 30 CFR 18.24 - Electrical clearances.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Electrical clearances. 18.24 Section 18.24... APPROVAL OF MINING PRODUCTS ELECTRIC MOTOR-DRIVEN MINE EQUIPMENT AND ACCESSORIES Construction and Design Requirements § 18.24 Electrical clearances. Minimum clearances between uninsulated electrical...

  13. 30 CFR 18.24 - Electrical clearances.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Electrical clearances. 18.24 Section 18.24... APPROVAL OF MINING PRODUCTS ELECTRIC MOTOR-DRIVEN MINE EQUIPMENT AND ACCESSORIES Construction and Design Requirements § 18.24 Electrical clearances. Minimum clearances between uninsulated electrical...

  14. Security Clearances: Consideration of Sexual Orientation in the Clearance Process.

    DTIC Science & Technology

    1995-03-01

    Until about 1991, when agencies began to change their security policies and practices regarding sexual orientation , there were a number of documented...cases where defense civilian or contractor employees’ security clearances were denied or revoked because of their sexual orientation . However our...forward and discuss their cases. Notwithstanding these limitations, our work disclosed no evidence that sexual orientation has been used as a criterion

  15. Removal - An alternative to clearance

    SciTech Connect

    Feinhals, J.; Kelch, A.; Kunze, V.

    2007-07-01

    This presentation shows the differences between the application of clearance and removal, both being procedures for materials leaving radiation protection areas permanently. The differentiation will be done on the basis of the German legislation but may be also applicable for other national legislation. For clearance in Germany two basic requirements must be given, i.e. that the materials are activated or contaminated and that they result from the licensed use or can be assigned to the scope of the license. Clearance needs not to be applied to objects in Germany which are to be removed only temporarily from controlled areas with the purpose of repair or reuse in other controlled areas. In these cases only the requirements of contamination control apply. In the case of removal it must either be proved by measurements that the relevant materials are neither activated nor contaminated or that the materials result from areas where activation or contamination is impossible due to the operational history considering operational procedures and events. If the material is considered neither activated nor contaminated there is no need for a clearance procedure. Therefore, these materials can be removed from radiation protection areas and the removal is in the responsibility of the licensee. Nevertheless, the removal procedure and the measuring techniques to be applied for the different types of materials need an agreement from the competent authority. In Germany a maximum value of 10% of the clearance values has been established in different licenses as a criterion for the application of removal. As approximately 2/3 of the total mass of a nuclear power plant is not expected to be contaminated or activated there is a need for such a procedure of removal for this non contaminated material without any regulatory control especially in the case of decommissioning. A remarkable example is NPP Stade where in the last three years more than 8600 Mg were disposed of by removal and

  16. Aerial Refueling Clearance Process Guide

    DTIC Science & Technology

    2014-08-21

    08-2014 2. REPORT TYPE Guidance Document 3. DATES COVERED 2008-2014 4. TITLE AND SUBTITLE Aerial Refueling Clearance Process Guide Attachment: Aerial...ATP-3.3.4.2 covers general operational procedures for AR and national/organizational SRDs cover data and procedures specific to their AR platforms...Receptacle, Probe/Drogue, and BDA Kit. 3.1.3 The items for assessment consideration cover several areas of interface for both the tanker and the

  17. Acute effect of inhaled bradykinin on tracheobronchial clearance in normal humans.

    PubMed Central

    Polosa, R; Hasani, A; Pavia, D; Agnew, J E; Lai, C K; Clarke, S W; Holgate, S T

    1992-01-01

    BACKGROUND: Bradykinin, a nonapeptide that contributes as a mediator to the pathogenesis of asthma, may affect lung mucociliary clearance, as it has been shown to be a potent secretagogue in canine airways and in human nasal mucosa in vivo. To evaluate this possibility the effect of inhaled bradykinin on mucociliary clearance has been studied in 10 healthy volunteers. METHODS: Subjects attended the laboratory on two occasions to take part in tracheobronchial clearance studies using a non-invasive radioisotopic technique. Inhalation of radioaerosol was followed 30 minutes later by inhalation of either bradykinin (8 mg/ml) or vehicle placebo in a randomised, double blind fashion. After each inhalation the number of coughs was recorded. Whole lung radioactivity was measured every half hour for six hours with two collimated scintillation counters, and a tracheobronchial clearance curve was plotted for each subject on each occasion. RESULTS: Mucociliary clearance, expressed as the area under the tracheobronchial radioaerosol retention curve calculated for the first six hours (AUC0-6h), was greater in nine out of 10 subjects after inhalation of bradykinin than after placebo. The median values (range) for AUC0-6h were significantly reduced from 126% (78-232%)/h with placebo to 87% (51-133%)/h with bradykinin. CONCLUSION: It is concluded that acute exposure to inhaled bradykinin accelerates tracheobronchial clearance in normal human airways. PMID:1465754

  18. Prediction of drug clearance in children.

    PubMed

    Foissac, Frantz; Bouazza, Naïm; Valade, Elodie; De Sousa Mendes, Mailys; Fauchet, Floris; Benaboud, Sihem; Hirt, Déborah; Tréluyer, Jean-Marc; Urien, Saïk

    2015-07-01

    The pediatric population is often exposed to drugs without sufficient knowledge about pharmacokinetics. The prediction of accurate clearance values in children, especially in neonates and infants, will improve the rational in dosing decisions. Drug clearances from birth to adulthood were compiled after a systematic review of pharmacokinetic reports. The analysis was performed using NONMEM. Clearance predictions were then evaluated by external validation. Prediction errors were also compared with those obtained from weight-based allometric scaling and physiologically based clearance (PBCL) models. For the analysis, 17 and 15 drugs were used for model building and external validation, respectively. A model based on the adult drug clearance value and taking into account both weight and age was retained. Age-related maturation of clearance reached 90% of the adult value within 1.5 years of life. For children less than 2 years old, allometric scaling alone systematically overestimated clearances. Accounting for age improved the clearance prediction in the 6 months-2 years age group (prediction error < 25%). Predictions obtained from the PBCL approach were close to our results. This analysis established a single equation using the adult clearance value as well as individual age and weight to predict drug clearance in children older than 6 months.

  19. Potential impact of mangrove clearance on biomass and biomass size spectra of nematode along the Sudanese Red Sea coast.

    PubMed

    Sabeel, Rasha Adam Osman; Vanreusel, Ann

    2015-02-01

    The potential effect of mangrove clearance on nematode assemblage biomass, biomass size spectra (NBSS) and abundance/biomass curves (ABC) was investigated in three sites representing a varying degree of mangrove clearance as well as in three stations established at each sites representing high-, mid- and low-water levels. Results revealed significant differences in sediment and nematode characteristics between the three sites. Although both the cleared and the intact mangrove had comparable biomass values, clear differences in biomass size spectra and abundance biomass curves were observed. The results suggested that the variation in the silt fraction and the food quality positively affected the total biomass. Mangrove clearance has caused a shift from a unimodal to a bimodal biomass size spectrum at all water levels, owing to an increase in smaller-bodied opportunistic non-selective deposit feeding nematodes. The ABC further confirmed the effect of clearance by classifying the cleared mangrove as moderately to grossly disturbed.

  20. The effect of single-dose tramadol on oxycodone clearance.

    PubMed

    Curry, Steven C; Watts, David J; Katz, Kenneth D; Bikin, Dale; Bukaveckas, Bonny L

    2007-11-01

    We have noticed increased prescribing of tramadol by emergency physicians for breakthrough pain in patients chronically taking oxycodone. Both oxycodone and tramadol undergo oxidative metabolism by CYP2D6 and CYP3A4, suggesting the possibility that tramadol may compete with oxycodone for metabolism. A randomized controlled trial in 10 human volunteers was performed to determine if single-dose tramadol therapy would impair oxycodone clearance. Subjects were randomized whether to enter the control or experimental arm of the study first, with each subject serving as his or her own control. In the control arm, each subject received 10 mg immediate-release oxycodone orally and had serial plasma oxycodone and oxymorphone concentrations measured over 8 h. The experimental arm was identical except that 100 mg tramadol was ingested 1.5 h before oxycodone. Clearance divided by fraction absorbed (CL/f) was calculated using the dose and the area under the 8-h time-plasma oxycodone concentration curve. Peak plasma oxycodone concentrations (C(max)) and time until peak oxycodone concentrations (T(max)) were secondary outcome parameters. Group size was chosen to produce a power of 0.8 to detect a 20% difference in CL/f between study arms. Values for CL/f, C(max), and T(max) were compared between study arms using two-tailed, paired t-tests. No statistically significant difference between groups was demonstrated for any parameter. We failed to demonstrate that single doses of tramadol impaired oxycodone clearance.

  1. Elastic clearance change in axisymmetric shearing process

    NASA Astrophysics Data System (ADS)

    Yoshida, Yoshinori

    2016-10-01

    An axisymmetric shearing experiment is conducted for a sheet of low carbon steel and stainless steel. Elastic change in the clearance between punch and die is measured. The increase of the clearance in shearing is confirmed and the influence of sheared material's flow stress on the clearance change is shown. Finite element analysis (FEA) of shearing with Gurson-Tvergaard-Needlman model (GTN model) is conducted for shearing of the carbon steels with rigid tools as a numerical experiment. Burr height is predicted in the FEA and the result is compared with the experimental result. In addition, the influence of the clearance on stress state in the material is investigated.

  2. Intelligent Engine Systems: HPT Clearance Control

    NASA Technical Reports Server (NTRS)

    2008-01-01

    The Advanced Thermally Actuated Clearance Control System underwent several studies. Improved flow path isolation quantified what can be gained by making the HPT case nearly adiabatic. The best method of heat transfer was established, and finally two different borrowed air cooling circuits were evaluated to be used for the HPT Active Clearance Control System.

  3. 14 CFR 25.925 - Propeller clearance.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... following: (a) Ground clearance. There must be a clearance of at least seven inches (for each airplane with nose wheel landing gear) or nine inches (for each airplane with tail wheel landing gear) between each propeller and the ground with the landing gear statically deflected and in the level takeoff, or...

  4. 14 CFR 25.925 - Propeller clearance.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... following: (a) Ground clearance. There must be a clearance of at least seven inches (for each airplane with nose wheel landing gear) or nine inches (for each airplane with tail wheel landing gear) between each propeller and the ground with the landing gear statically deflected and in the level takeoff, or...

  5. 14 CFR 25.925 - Propeller clearance.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... following: (a) Ground clearance. There must be a clearance of at least seven inches (for each airplane with nose wheel landing gear) or nine inches (for each airplane with tail wheel landing gear) between each propeller and the ground with the landing gear statically deflected and in the level takeoff, or...

  6. 19 CFR 122.77 - Clearance certificate.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Clearance certificate. 122.77 Section 122.77 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Documents Required for Clearance and Permission To Depart;...

  7. 19 CFR 122.77 - Clearance certificate.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 19 Customs Duties 1 2011-04-01 2011-04-01 false Clearance certificate. 122.77 Section 122.77 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Documents Required for Clearance and Permission To Depart;...

  8. 19 CFR 122.77 - Clearance certificate.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 19 Customs Duties 1 2014-04-01 2014-04-01 false Clearance certificate. 122.77 Section 122.77 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Documents Required for Clearance and Permission To Depart;...

  9. 19 CFR 122.77 - Clearance certificate.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 19 Customs Duties 1 2013-04-01 2013-04-01 false Clearance certificate. 122.77 Section 122.77 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Documents Required for Clearance and Permission To Depart;...

  10. 19 CFR 122.77 - Clearance certificate.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 19 Customs Duties 1 2012-04-01 2012-04-01 false Clearance certificate. 122.77 Section 122.77 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Documents Required for Clearance and Permission To Depart;...

  11. 15 CFR 752.15 - Export clearance.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 15 Commerce and Foreign Trade 2 2010-01-01 2010-01-01 false Export clearance. 752.15 Section 752... OF INDUSTRY AND SECURITY, DEPARTMENT OF COMMERCE EXPORT ADMINISTRATION REGULATIONS SPECIAL COMPREHENSIVE LICENSE § 752.15 Export clearance. (a) Shipper's Export Declaration (SED) or Automated...

  12. 14 CFR 25.925 - Propeller clearance.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... nose wheel landing gear) or nine inches (for each airplane with tail wheel landing gear) between each propeller and the ground with the landing gear statically deflected and in the level takeoff, or taxiing... the corresponding landing gear strut bottomed. (b) Water clearance. There must be a clearance of...

  13. 30 CFR 56.7018 - Hand clearance.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Hand clearance. 56.7018 Section 56.7018 Mineral... Drilling § 56.7018 Hand clearance. Persons shall not hold the drill steel while collaring holes, or rest their hands on the chuck or centralizer while drilling....

  14. 30 CFR 56.7018 - Hand clearance.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Hand clearance. 56.7018 Section 56.7018 Mineral... Drilling § 56.7018 Hand clearance. Persons shall not hold the drill steel while collaring holes, or rest their hands on the chuck or centralizer while drilling....

  15. 30 CFR 57.7028 - Hand clearance.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Hand clearance. 57.7028 Section 57.7028 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... Drilling-Underground Only § 57.7028 Hand clearance. Persons shall not rest their hands on the chuck...

  16. 30 CFR 57.7018 - Hand clearance.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Hand clearance. 57.7018 Section 57.7018 Mineral... Drilling-Surface Only § 57.7018 Hand clearance. Persons shall not hold the drill steel while collaring holes, or rest their hands on the chuck or centralizer while drilling. Drilling—Underground Only...

  17. 30 CFR 57.7018 - Hand clearance.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Hand clearance. 57.7018 Section 57.7018 Mineral... Drilling-Surface Only § 57.7018 Hand clearance. Persons shall not hold the drill steel while collaring holes, or rest their hands on the chuck or centralizer while drilling. Drilling—Underground Only...

  18. 30 CFR 57.7028 - Hand clearance.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Hand clearance. 57.7028 Section 57.7028 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... Drilling-Underground Only § 57.7028 Hand clearance. Persons shall not rest their hands on the chuck...

  19. 30 CFR 57.7018 - Hand clearance.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Hand clearance. 57.7018 Section 57.7018 Mineral... Drilling-Surface Only § 57.7018 Hand clearance. Persons shall not hold the drill steel while collaring holes, or rest their hands on the chuck or centralizer while drilling. Drilling—Underground Only...

  20. 30 CFR 57.7028 - Hand clearance.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Hand clearance. 57.7028 Section 57.7028 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... Drilling-Underground Only § 57.7028 Hand clearance. Persons shall not rest their hands on the chuck...

  1. 30 CFR 57.7018 - Hand clearance.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Hand clearance. 57.7018 Section 57.7018 Mineral... Drilling-Surface Only § 57.7018 Hand clearance. Persons shall not hold the drill steel while collaring holes, or rest their hands on the chuck or centralizer while drilling. Drilling—Underground Only...

  2. 30 CFR 57.7028 - Hand clearance.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Hand clearance. 57.7028 Section 57.7028 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... Drilling-Underground Only § 57.7028 Hand clearance. Persons shall not rest their hands on the chuck...

  3. 30 CFR 57.7018 - Hand clearance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Hand clearance. 57.7018 Section 57.7018 Mineral... Drilling-Surface Only § 57.7018 Hand clearance. Persons shall not hold the drill steel while collaring holes, or rest their hands on the chuck or centralizer while drilling. Drilling—Underground Only...

  4. 30 CFR 57.7028 - Hand clearance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Hand clearance. 57.7028 Section 57.7028 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND... Drilling-Underground Only § 57.7028 Hand clearance. Persons shall not rest their hands on the chuck...

  5. 30 CFR 56.7018 - Hand clearance.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Hand clearance. 56.7018 Section 56.7018 Mineral... Drilling § 56.7018 Hand clearance. Persons shall not hold the drill steel while collaring holes, or rest their hands on the chuck or centralizer while drilling....

  6. 30 CFR 56.7018 - Hand clearance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Hand clearance. 56.7018 Section 56.7018 Mineral... Drilling § 56.7018 Hand clearance. Persons shall not hold the drill steel while collaring holes, or rest their hands on the chuck or centralizer while drilling....

  7. 30 CFR 56.7018 - Hand clearance.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Hand clearance. 56.7018 Section 56.7018 Mineral... Drilling § 56.7018 Hand clearance. Persons shall not hold the drill steel while collaring holes, or rest their hands on the chuck or centralizer while drilling....

  8. 30 CFR 56.11010 - Stairstep clearance.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Stairstep clearance. 56.11010 Section 56.11010 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... warning signs or similar devices shall be provided to indicate an impaired clearance....

  9. 30 CFR 56.11010 - Stairstep clearance.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Stairstep clearance. 56.11010 Section 56.11010 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... warning signs or similar devices shall be provided to indicate an impaired clearance....

  10. Nasal mucociliary clearance after radiation therapy.

    PubMed

    Stringer, S P; Stiles, W; Slattery, W H; Krumerman, J; Parsons, J T; Mendenhall, W M; Cassisi, N J

    1995-04-01

    Irradiation has been demonstrated to cause decreased mucociliary clearance in animal models. We sought to verify this effect clinically by using the saccharin transport test to evaluate nasal mucociliary clearance in 9 patients previously treated with radiation therapy to the nasal cavity. The patients also completed a questionnaire examining the prevalence of nasal symptoms before and after radiation therapy. Patients who received radiation therapy had no clearance of saccharin from the nasal cavity at a minimum of 20 minutes. The controls had a median clearance time of 5 minutes. The patients noted a higher prevalence of nasal congestion, drainage, and facial pain after radiation therapy. This study demonstrates that radiation therapy to the nasal cavity causes a decrease in nasal mucociliary clearance. This alteration should be considered when selecting therapy for malignancies in the nasal area.

  11. Effects of lung volume on clearance of solutes from the air spaces of lungs

    SciTech Connect

    Peterson, B.T.; James, H.L.; McLarty, J.W.

    1988-03-01

    Several investigators have shown that the clearance rate of aerosolized 99mTc-labeled diethylenetriamine pentaacetate (DTPA, mol wt = 492, radius = 0.6 nm) from the air spaces of the lungs of humans and experimental animals increases with lung volume. To further investigate this phenomenon we performed a compartmental analysis of the 2-h clearance of DTPA from the lungs of anesthetized sheep using a new method to more accurately correct for the effects of DTPA recirculation. This analysis showed that the DTPA clearance in eight sheep ventilated with zero end-expired pressure was best described by a one-compartment model with a clearance rate of 0.42 +/- 0.15%/min. Ventilating eight sheep with an end-expired pressure of 10 cmH/sub 2/O throughout the study increased the end-expired volume 0.4 +/- 0.1 liter BTPS and created a clearance curve that was best described by a two-compartment model. In these sheep 56 +/- 16% of the DTPA cleared from the lungs at a rate of 7.9 +/- 2.9%/min. The remainder cleared at a rate similar to that measured in the sheep ventilated with zero end-expired pressure (0.35 +/- 0.18%/min). Additional control and lung inflation experiments were performed using /sup 99m/Tc-labeled human serum albumin (mol wt = 66,000, radius = 3.6 nm). In six control sheep ventilated with zero end-expired pressure the albumin clearance was best described by a one-compartment model with a clearance rate of 0.06 +/- 0.02%/min. The clearance rate in six sheep with increased lung volume was slightly larger (0.09 +/- 0.02, P less than 0.05) but was well described by a one-compartment model.

  12. 19 CFR 4.61 - Requirements for clearance.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... optional clearance locations. (b) When clearance required. Under certain circumstances, American vessels.... While American vessels transporting unentered foreign merchandise must fully comply with usual clearance procedures, American vessels carrying no unentered foreign merchandise but that have in-bond...

  13. 77 FR 21989 - Critical Infrastructure Private Sector Clearance Program Request

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-12

    ... SECURITY Critical Infrastructure Private Sector Clearance Program Request AGENCY: National Protection and... information provided. SUPPLEMENTARY INFORMATION: The Critical Infrastructure Private Sector Clearance Program (PSCP) sponsors clearances for private sector partners who are responsible for critical...

  14. Advanced optical blade tip clearance measurement system

    NASA Technical Reports Server (NTRS)

    Ford, M. J.; Honeycutt, R. E.; Nordlund, R. E.; Robinson, W. W.

    1978-01-01

    An advanced electro-optical system was developed to measure single blade tip clearances and average blade tip clearances between a rotor and its gas path seal in an operating gas turbine engine. This system is applicable to fan, compressor, and turbine blade tip clearance measurement requirements, and the system probe is particularly suitable for operation in the extreme turbine environment. A study of optical properties of blade tips was conducted to establish measurement system application limitations. A series of laboratory tests was conducted to determine the measurement system's operational performance characteristics and to demonstrate system capability under simulated operating gas turbine environmental conditions. Operational and environmental performance test data are presented.

  15. Plasma Creatinine Clearance in the Dog

    ERIC Educational Resources Information Center

    Frazier, Loy W.

    1977-01-01

    Lists materials and methods for an experiment that demonstrates the concept of glomerular filtration rate (GFR) using anesthesized dogs. In the dog, GFR is equivalent to the renal plasma clearance of exogenous creatinine. (CS)

  16. 14 CFR 25.925 - Propeller clearance.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... attitude, whichever is most critical. In addition, there must be positive clearance between the propeller and the ground when in the level takeoff attitude with the critical tire(s) completely deflated...

  17. Shear-Joint Capability Versus Bolt Clearance

    NASA Technical Reports Server (NTRS)

    Lee, H. M.

    1994-01-01

    NASA Technical Memorandum presents theoretical study of relationships between load-bearing capabilities of shear joints that comprise plates clamped together by multiple bolts and clearances between bolts and boltholes in those joints.

  18. Shear joint capability versus bolt clearance

    NASA Technical Reports Server (NTRS)

    Lee, H. M.

    1992-01-01

    The results of a conservative analysis approach into the determination of shear joint strength capability for typical space-flight hardware as a function of the bolt-hole clearance specified in the design are presented. These joints are comprised of high-strength steel fasteners and abutments constructed of aluminum alloys familiar to the aerospace industry. A general analytical expression was first arrived at which relates bolt-hole clearance to the bolt shear load required to place all joint fasteners into a shear transferring position. Extension of this work allowed the analytical development of joint load capability as a function of the number of fasteners, shear strength of the bolt, bolt-hole clearance, and the desired factor of safety. Analysis results clearly indicate that a typical space-flight hardware joint can withstand significant loading when less than ideal bolt hole clearances are used in the design.

  19. Compressor airfoil tip clearance optimization system

    DOEpatents

    Little, David A.; Pu, Zhengxiang

    2015-08-18

    A compressor airfoil tip clearance optimization system for reducing a gap between a tip of a compressor airfoil and a radially adjacent component of a turbine engine is disclosed. The turbine engine may include ID and OD flowpath boundaries configured to minimize compressor airfoil tip clearances during turbine engine operation in cooperation with one or more clearance reduction systems that are configured to move the rotor assembly axially to reduce tip clearance. The configurations of the ID and OD flowpath boundaries enhance the effectiveness of the axial movement of the rotor assembly, which includes movement of the ID flowpath boundary. During operation of the turbine engine, the rotor assembly may be moved axially to increase the efficiency of the turbine engine.

  20. Voltage-clearance recommendations for printed boards

    SciTech Connect

    Jennings, C W; Cave, G; Evans, A; Harrington, D J; Kirchenbaum, J; Martz, R E; Mierendorf, R C; Smith, G A

    1980-01-01

    Present and future trends in printed board designs point to higher circuit densities with narrower lines and closer spacings. Some designers are now laying out boards with 0.13 mm lines and spacings. The reduction of nominal spacing between conductive elements has raised questions concerning the adequacy of present voltage-clearance recommendations. The present recommendations are considered too conservative in that they are weighted with large safety factors, especially for small clearances, and are frequently disregarded by many designers. Published voltage breakdown measurements made on printed boards with comb patterns with their enhanced conductor test lengths show breakdowns occurring at much higher voltages than those specified for the clearances in existing documents. A Task Group was set up to review published breakdown measurements and to make any additional measurements necessary to provide voltage-clearance recommendations. These recommendations are reported.

  1. 2015 Annual Report on Security Clearance Determinations

    DTIC Science & Technology

    2016-06-28

    preceding fiscal year that resulted in a denial or revocation of a security clearance...and o more than 1 year. iii. Percentage of reviews during the preceding fiscal year that resulted in a denial or revocation of a security clearance...1,322 in FY 2014 to 2,526 in FY 20154. iii. The percentage of reviews during the preceding fiscal year that resulted in a denial or revocation of a

  2. Controls Considerations for Turbine Active Clearance Control

    NASA Technical Reports Server (NTRS)

    Melcher, Kevin J.

    2004-01-01

    This presentation discusses active control of turbine tip clearance from a control systems perspective. It is a subset of charts that were presented at the 2003 meeting of the International Society of Air Breathing Engines which was held August 31 through September 5 in Cleveland, Ohio. The associated reference paper is cited at the end of the presentation. The presentation describes active tip clearance control research being conducted by NASA to improve turbine engine systems. The target application for this effort is commercial aircraft engines. However, it is believed that the technologies developed as part of this research will benefit a broad spectrum of current and future turbomachinery. The first part of the presentation discusses the concept of tip clearance, problems associated with it, and the benefits of controlling it. It lays out a framework for implementing tip clearance controls that enables the implementation to progress from purely analytical to hardware-in-the-loop to fully experimental. And it briefly discusses how the technologies developed will be married to the previously described ACC Test Rig for hardware-in-the-loop demonstrations. The final portion of the presentation, describes one of the key technologies in some detail by presenting equations and results for a functional dynamic model of the tip clearance phenomena. As shown, the model exhibits many of the clearance dynamics found in commercial gas turbine engines. However, initial attempts to validate the model identified limitations that are being addressed to make the model more realistic.

  3. ADAPTIVE CLEARANCE CONTROL SYSTEMS FOR TURBINE ENGINES

    NASA Technical Reports Server (NTRS)

    Blackwell, Keith M.

    2004-01-01

    The Controls and Dynamics Technology Branch at NASA Glenn Research Center primarily deals in developing controls, dynamic models, and health management technologies for air and space propulsion systems. During the summer of 2004 I was granted the privilege of working alongside professionals who were developing an active clearance control system for commercial jet engines. Clearance, the gap between the turbine blade tip and the encompassing shroud, increases as a result of wear mechanisms and rubbing of the turbine blades on shroud. Increases in clearance cause larger specific fuel consumption (SFC) and loss of efficient air flow. This occurs because, as clearances increase, the engine must run hotter and bum more fuel to achieve the same thrust. In order to maintain efficiency, reduce fuel bum, and reduce exhaust gas temperature (EGT), the clearance must be accurately controlled to gap sizes no greater than a few hundredths of an inch. To address this problem, NASA Glenn researchers have developed a basic control system with actuators and sensors on each section of the shroud. Instead of having a large uniform metal casing, there would be sections of the shroud with individual sensors attached internally that would move slightly to reform and maintain clearance. The proposed method would ultimately save the airline industry millions of dollars.

  4. Genetic variants in interferon-λ 4 influences HCV clearance in Chinese Han population

    PubMed Central

    Huang, Peng; Yao, Yinan; Yue, Ming; Tian, Ting; Chen, Hongbo; Chen, Mingzhu; Wang, Jie; Zhang, Yun; Yu, Rongbin

    2017-01-01

    Recent many studies indicated a novel dinucleotide variant in ss469415590 (TT vs. ΔG) of interferon-λ 4 (IFNL4) gene strongly associated with hepatitis C virus clearance. To evaluate the impact and clinical usefulness of IFNL4 ss469415590 genotype on predicting both spontaneous HCV clearance and response to therapy in Chinese population, we genotyped 795 chronic HCV carriers, 460 subjects with HCV natural clearance and 362 patients with pegylated interferon-α and ribavirin (PEG IFN-α/RBV) treatment. IFNL4 ss469415590 variant genotypes significantly decreased host HCV clearance, both spontaneous (dominant model: OR = 0.50, 95% CI = 0.36–0.71) and IFN-α induced (dominant model: OR = 0.32, 95% CI = 0.18–0.56). Multivariate stepwise analysis indicated that ss469415590, rs12979860, the level of baseline HCV RNA and platelet were as independent predictors for sustained virological response (SVR). But the area under the ROC curve (AUC) was only 0.58 for ss469415590, and it was elevated to 0.71 by adding rs12979860, baseline HCV RNA and platelet in the prediction model of SVR. Therefore, these findings underscore that although genetic factors of host and pathogen were commonly important during HCV clearance, ss469415590 may be also a strongly predictive marker in the Chinese population. PMID:28186161

  5. Clearance of Tc-99m DTPA aerosol from coal miners' lungs

    SciTech Connect

    Susskind, H.; Brill, A.B.; Harold, W.H.

    1985-07-01

    Alterations in regional epithelial permeability were assessed in 22 retired West Virginia coal miners' lungs by measuring the clearance of inhaled 0.5-..mu..m Tc-99m DTPA aerosol. Activity was measured in both lungs and in regions of interest placed over the lung periphery in the apical, middle, and basal portions of each lung. Clearance rates (T/sub 1/2/) for 5 nonsmokers, 8 ex-smokers, and 9 smokers were significantly faster than for comparable subjects measured elsewhere, who were not coal miners. Regional apex-to-base distributions of DTPA were measured as a function of clearance time and compared with regional ventilation and perfusion. Regional, as well as overall lung clearance curves of 8 smokers and 4 ex-smokers had two components, with overall T/sub 1/2/ of <7 min for the faster one. No correlations were found between T/sub 1/2/ and DLCO or with P(A-a)O/sub 2/. The results of our study suggest that measurement of DTPA clearance is a potentially useful noninvasive technique to assess lung injury in miners exposed to coal dust. 14 refs., 6 figs., 2 tabs.

  6. 48 CFR 945.603-70 - Plant clearance function.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 5 2011-10-01 2011-10-01 false Plant clearance function... Plant clearance function. If the plant clearance function has not been formally delegated to another Federal agency, the contracting officer shall assume all responsibilities of the plant clearance...

  7. 48 CFR 245.7203 - Assigning plant clearance case numbers.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Assigning plant clearance....7203 Assigning plant clearance case numbers. (a) Use a three-part, 11-character number constructed as... clearance number on DD Form 1635, Plant Clearance Case Register, or mechanized equivalent....

  8. 48 CFR 245.7202 - Establishing a plant clearance case.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... clearance case. 245.7202 Section 245.7202 Federal Acquisition Regulations System DEFENSE ACQUISITION....7202 Establishing a plant clearance case. (a) Upon receipt of an acceptable inventory schedule or a DD Form 1342, DoD Property Record, the plant clearance officer shall establish a plant clearance case...

  9. 7 CFR 1927.55 - Title clearance services.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 12 2010-01-01 2010-01-01 false Title clearance services. 1927.55 Section 1927.55... REGULATIONS TITLE CLEARANCE AND LOAN CLOSING Real Estate Title Clearance and Loan Closing § 1927.55 Title clearance services. (a) Responsibilities of closing agents. Services to be provided to the agency and...

  10. 48 CFR 945.603-70 - Plant clearance function.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Plant clearance function... Plant clearance function. If the plant clearance function has not been formally delegated to another Federal agency, the contracting officer shall assume all responsibilities of the plant clearance...

  11. 48 CFR 945.603-70 - Plant clearance function.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Plant clearance function... Plant clearance function. If the plant clearance function has not been formally delegated to another Federal agency, the contracting officer shall assume all responsibilities of the plant clearance...

  12. 48 CFR 801.602-76 - Business clearance review.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 5 2014-10-01 2014-10-01 false Business clearance review... Authority, and Responsibilities 801.602-76 Business clearance review. (a) A business clearance review is a... obtain a business clearance review prior to award of any contract, task or delivery order, or...

  13. 48 CFR 801.602-76 - Business clearance review.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 5 2013-10-01 2013-10-01 false Business clearance review... Authority, and Responsibilities 801.602-76 Business clearance review. (a) A business clearance review is a... obtain a business clearance review prior to award of any contract, task or delivery order, or...

  14. 32 CFR 644.517 - Clearance of Army lands.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 32 National Defense 4 2013-07-01 2013-07-01 false Clearance of Army lands. 644.517 Section 644.517... ESTATE HANDBOOK Disposal Clearance of Explosive Hazards and Other Contamination from Proposed Excess Land and Improvements § 644.517 Clearance of Army lands. The responsibility for performing clearance...

  15. 32 CFR 644.517 - Clearance of Army lands.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 32 National Defense 4 2012-07-01 2011-07-01 true Clearance of Army lands. 644.517 Section 644.517... ESTATE HANDBOOK Disposal Clearance of Explosive Hazards and Other Contamination from Proposed Excess Land and Improvements § 644.517 Clearance of Army lands. The responsibility for performing clearance...

  16. 32 CFR 644.517 - Clearance of Army lands.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 32 National Defense 4 2014-07-01 2013-07-01 true Clearance of Army lands. 644.517 Section 644.517... ESTATE HANDBOOK Disposal Clearance of Explosive Hazards and Other Contamination from Proposed Excess Land and Improvements § 644.517 Clearance of Army lands. The responsibility for performing clearance...

  17. 32 CFR 644.517 - Clearance of Army lands.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true Clearance of Army lands. 644.517 Section 644.517... ESTATE HANDBOOK Disposal Clearance of Explosive Hazards and Other Contamination from Proposed Excess Land and Improvements § 644.517 Clearance of Army lands. The responsibility for performing clearance...

  18. Atorvastatin delays the glucose clearance rate in hypercholesterolemic rabbits.

    PubMed

    Cheng, Daxin; Wang, Yanli; Gao, Shoucui; Wang, Xiaojing; Sun, Wentao; Bai, Liang; Cheng, Gong; Chu, Yonglie; Zhao, Sihai; Liu, Enqi

    2015-05-01

    The administration of statin might increase the risk of new-onset diabetes in hypercholesterolemic patients based on the recent clinical evidence. However, the causal relationship must be clarified and confirmed in animal experiments. Therefore, we mimicked hypercholesterolemia by feeding rabbits a high-cholesterol diet (HCD) and performed 16 weeks of atorvastatin administration to investigate the effect of statin on glucose metabolism. The intravenous glucose tolerance test showed that plasma glucose levels in the statin-treated rabbits were consistently higher and that there was a slower rate of glucose clearance from the blood than in HCD rabbits. The incremental area under the curve for glucose in the statin-treated rabbits was also significantly larger than in the HCD rabbits. However, there was no significant difference between the two groups in the intravenous insulin tolerance test. The glucose-lowering ability of exogenous insulin was not impaired by statin treatment in hypercholesterolemic rabbits. The administration of a single dose of statin did not affect glucose metabolism in normal rabbits. The statin also significantly increased the levels of high-density lipoprotein cholesterol, alanine aminotransferase and aspartate transaminase and decreased plasma levels of total cholesterol, triglycerides and low-density lipoprotein cholesterol in the hypercholesterolemic rabbits, whereas it did not affect plasma levels of glucose and insulin. The current results showed that atorvastatin treatment resulted in a significant delay of glucose clearance in hypercholesterolemic rabbits, and this rabbit model could be suitable for studying the effects of statin on glucose metabolism.

  19. Lower metabolic clearance of tizanidine in Japanese subjects.

    PubMed

    Momo, Kenji; Homma, Masato; Kohda, Yukinao

    2013-12-01

    Our aim was to determine whether metabolic clearance, renal clearance, or both elimination pathways contribute to ethnic differences in tizanidine clearance, which is ~ 2-fold higher in Caucasians than in Asians. The pharmacokinetic parameters of tizanidine in 9 healthy male Japanese subjects were compared with those of Caucasians in previous studies. Metabolic clearance of tizanidine was lower in Japanese than in Caucasian subjects (5.9 vs. 8.1 - 10.9 l/h/kg), although renal clearances were similar (0.040 vs. 0.047 - 0.055 l/h/kg). The results suggest that ethnic differences in tizanidine clearance are due to differences in metabolic clearance.

  20. Effects of airborne pollutants on mucociliary clearance.

    PubMed Central

    Wolff, R K

    1986-01-01

    The mucociliary clearance system is a first line of defense against inhaled agents, and so its compromise can adversely affect health. The purpose of this paper is to provide a review of data on the effect of in vivo air pollutant exposures on the clearance of test particles from airways. Data from both animals and humans are compared whenever possible, so that estimates of human health effects may be made. Mechanisms of action are also discussed, presenting the view that for low level exposures, changes in secretions are probably responsible for most observed changes in clearance. The pollutants pertinent to this review are those that are common in the environment and most likely to have impacts on large numbers of people: sulfur oxides, sulfuric acid mist, O3, NO2, particulates, diesel exhaust, and cigarette smoke. Images FIGURE 1. FIGURE 2. a FIGURE 2. b FIGURE 4. PMID:3519203

  1. Effects of airborne pollutants on mucociliary clearance

    SciTech Connect

    Wolff, R.K.

    1986-04-01

    The mucociliary clearance system is a first line of defense against inhaled agents, and so its compromise can adversely affect health. The purpose of this paper is to provide a review of data on the effect of in vivo air pollutant exposures on the clearance of test particles from airways. Data from both animals and humans are compared whenever possible, so that estimates of human health effects may be made. Mechanisms of action are also discussed, presenting the view that for low level exposures, changes in secretions are probably responsible for most observed changes in clearance. The pollutants pertinent to this review are those that are common in the environment and most likely to have impacts on large numbers of people: sulfur oxides, sulfuric acid mist, O/sub 3/, NO/sub 2/, particulates, diesel exhaust, and cigarette smoke.149 references.

  2. Predicting Clearance Mechanism in Drug Discovery: Extended Clearance Classification System (ECCS).

    PubMed

    Varma, Manthena V; Steyn, Stefanus J; Allerton, Charlotte; El-Kattan, Ayman F

    2015-12-01

    Early prediction of clearance mechanisms allows for the rapid progression of drug discovery and development programs, and facilitates risk assessment of the pharmacokinetic variability associated with drug interactions and pharmacogenomics. Here we propose a scientific framework--Extended Clearance Classification System (ECCS)--which can be used to predict the predominant clearance mechanism (rate-determining process) based on physicochemical properties and passive membrane permeability. Compounds are classified as: Class 1A--metabolism as primary systemic clearance mechanism (high permeability acids/zwitterions with molecular weight (MW) ≤400 Da), Class 1B--transporter-mediated hepatic uptake as primary systemic clearance mechanism (high permeability acids/zwitterions with MW >400 Da), Class 2--metabolism as primary clearance mechanism (high permeability bases/neutrals), Class 3A--renal clearance (low permeability acids/zwitterions with MW ≤400 Da), Class 3B--transporter mediated hepatic uptake or renal clearance (low permeability acids/zwitterions with MW >400 Da), and Class 4--renal clearance (low permeability bases/neutrals). The performance of the ECCS framework was validated using 307 compounds with single clearance mechanism contributing to ≥70% of systemic clearance. The apparent permeability across clonal cell line of Madin - Darby canine kidney cells, selected for low endogenous efflux transporter expression, with a cut-off of 5 × 10(-6) cm/s was used for permeability classification, and the ionization (at pH7) was assigned based on calculated pKa. The proposed scheme correctly predicted the rate-determining clearance mechanism to be either metabolism, hepatic uptake or renal for ~92% of total compounds. We discuss the general characteristics of each ECCS class, as well as compare and contrast the framework with the biopharmaceutics classification system (BCS) and the biopharmaceutics drug disposition classification system (BDDCS

  3. Pharmacologic agents for mucus clearance in bronchiectasis.

    PubMed

    Nair, Girish B; Ilowite, Jonathan S

    2012-06-01

    There are no approved pharmacologic agents to enhance mucus clearance in non-cystic fibrosis (CF) bronchiectasis. Evidence supports the use of hyperosmolar agents in CF, and studies with inhaled mannitol and hypertonic saline are ongoing in bronchiectasis. N-acetylcysteine may act more as an antioxidant than a mucolytic in other lung diseases. Dornase α is beneficial to patients with CF, but is not useful in patients with non-CF bronchiectasis. Mucokinetic agents such as β-agonists have the potential to improve mucociliary clearance in normals and many disease states, but have not been adequately studied in patients with bronchiectasis.

  4. Mucociliary clearance from the calf lung.

    PubMed Central

    Jones, C D

    1983-01-01

    Mucociliary clearance rate constants for ten calves were obtained using Technetium 99m-sulphur colloid complex. The mean rate constant measured at the lung for all calves was 0.012 (+/- 0.009) min-1 (half-life 58 minutes). The clearance rate constants obtained from measurements made at the larynx were higher (0.02 +/- 0.007 min-1), although not significantly higher, than those determined from measurements taken at the lung. The constants can be used to predict the particle burden on the lungs of calves kept under husbandry systems of varying air hygiene. Images Fig. 1. PMID:6640409

  5. Deposition-dependent normal ranges for radioaerosol assessment of lung mucus clearance.

    PubMed

    Agnew, John E; Hasani, Amir

    2008-12-01

    Deposition distribution variability strongly influences data from radioaerosol mucus clearance measurements. We investigated how one clearance measurement-the area under the 0-6 h tracheobronchial retention curve (AUC)-relates to three different indices characterizing initial particle distribution. These indices were a conventional penetration index (PI), retention at 24 h (R(24)) and an Airways Penetration Index (API). API is an estimate of an outer to inner zone ratio for "tracheobronchial" (short-term cleared) deposition. Data were analyzed from "control" tests on 35 normal nonsmoking volunteers (16 females, 19 males, age 18-72 years). The strongest clearance-deposition correlation (r = 0.84, p < 0.0001) was obtained with API, yielding a narrower normal range than those with PI or R(24). No influence of age was detected. Data from repeat tests on 17 subjects demonstrated AUC changes correlating closely with API changes (r = 0.92, p < 0.0001), confirming the potential value of API as a "predictor" of clearance changes resulting simply from a changed distribution of initial deposition along the tracheobronchial airway generations. Additional data from 19 "placebo" tests on normal subjects gave AUC values within or close to suggested normal confidence limits derived from the control subject plots of AUC against, respectively, PI, R(24), and API. Quantitative attention to the influence of depositionclearance relationships should help in analyzing data from studies where posttreatment aerosol distribution cannot be exactly matched to the pretreatment situation. Deposition-corrected clearance provides an approach to improved estimation of clearance "normality."

  6. The Skipping Rope Curve

    ERIC Educational Resources Information Center

    Nordmark, Arne; Essen, Hanno

    2007-01-01

    The equilibrium of a flexible inextensible string, or chain, in the centrifugal force field of a rotating reference frame is investigated. It is assumed that the end points are fixed on the rotation axis. The shape of the curve, the skipping rope curve or "troposkien", is given by the Jacobi elliptic function sn. (Contains 3 figures.)

  7. Anodic Polarization Curves Revisited

    ERIC Educational Resources Information Center

    Liu, Yue; Drew, Michael G. B.; Liu, Ying; Liu, Lin

    2013-01-01

    An experiment published in this "Journal" has been revisited and it is found that the curve pattern of the anodic polarization curve for iron repeats itself successively when the potential scan is repeated. It is surprising that this observation has not been reported previously in the literature because it immediately brings into…

  8. Flow-duration curves

    USGS Publications Warehouse

    Searcy, James Kincheon

    1959-01-01

    The flow-duration curve is a cumulative frequency curve that shows the percent of time specified discharges were equaled or exceeded during a given period. It combines in one curve the flow characteristics of a stream throughout the range of discharge, without regard to the sequence of occurrence. If the period upon which the curve is based represents the long-term flow of a stream, the curve may be used to predict the distribution of future flows for water- power, water-supply, and pollution studies. This report shows that differences in geology affect the low-flow ends of flow-duration curves of streams in adjacent basins. Thus, duration curves are useful in appraising the geologic characteristics of drainage basins. A method for adjusting flow-duration curves of short periods to represent long-term conditions is presented. The adjustment is made by correlating the records of a short-term station with those of a long-term station.

  9. Simulating Supernova Light Curves

    SciTech Connect

    Even, Wesley Paul; Dolence, Joshua C.

    2016-05-05

    This report discusses supernova light simulations. A brief review of supernovae, basics of supernova light curves, simulation tools used at LANL, and supernova results are included. Further, it happens that many of the same methods used to generate simulated supernova light curves can also be used to model the emission from fireballs generated by explosions in the earth’s atmosphere.

  10. Tornado-Shaped Curves

    ERIC Educational Resources Information Center

    Martínez, Sol Sáez; de la Rosa, Félix Martínez; Rojas, Sergio

    2017-01-01

    In Advanced Calculus, our students wonder if it is possible to graphically represent a tornado by means of a three-dimensional curve. In this paper, we show it is possible by providing the parametric equations of such tornado-shaped curves.

  11. Effects of prolonged bedrest in antiorthostatic position on rCBF measured by /sup 133/Xe inhalation technique - effects of clonidine

    SciTech Connect

    Guell, A.; Victor, G.; Bru, A.; Montastruc, P.; Bes, A.

    1981-12-01

    Experiments involving prolonged bedrest in antiorthostatic position were performed in order to simulate cardiovascular changes observed in weightlessness. Six young healthy subjects were placed in strict bedrest in a -4-deg antiorthostatic position for seven days. The rCBF (regional cerebral blood flow) measurements were made by an Xe-133 inhalation method. Three of the subjects received 0.450 mg of clonidine during the experiment. A constant increase in rCBF was observed during the first 12 hours in subjects who did not receive clonidine at the 72nd hour, all values returned to the basal state. These findings agree with the rapid correction of hemodynamic disturbances observed in the first days of weightlessness. In subjects treated with clonidine, the increase in rCBF did not occur.

  12. Mechanism of ritonavir changes in methadone pharmacokinetics and pharmacodynamics: I. Evidence against CYP3A mediation of methadone clearance.

    PubMed

    Kharasch, E D; Bedynek, P S; Park, S; Whittington, D; Walker, A; Hoffer, C

    2008-10-01

    Ritonavir diminishes methadone plasma concentrations, an effect attributed to CYP3A induction, but the actual mechanisms are unknown. We determined ritonavir effects on stereoselective methadone pharmacokinetics and clinical effects (pupillary miosis) in healthy human immunodeficiency virus-negative volunteers. Subjects received intravenous plus oral (deuterium-labeled) racemic methadone after no ritonavir, short-term (3-day) ritonavir, and steady-state ritonavir. Acute and steady-state ritonavir, respectively, caused 1.5- and 2-fold induction of systemic and apparent oral R- and S-methadone clearances. Ritonavir increased renal clearance 40-50%, and stereoselectively (S > R) increased hepatic methadone N-demethylation 50-80%, extraction twofold, and clearance twofold. Bioavailability was unchanged despite significant inhibition of intestinal P-glycoprotein. Intestinal and hepatic CYP3A was inhibited > 70%. Ritonavir shifted methadone plasma concentration-miosis curves leftward and upward. Rapid ritonavir induction of methadone clearance results from increased renal clearance and induced hepatic metabolism. Induction of methadone metabolism occurred despite profound CYP3A inhibition, suggesting no role for CYP3A in clinical methadone metabolism and clearance. Ritonavir may alter methadone pharmacodynamics.

  13. CURVES: curve evolution for vessel segmentation.

    PubMed

    Lorigo, L M; Faugeras, O D; Grimson, W E; Keriven, R; Kikinis, R; Nabavi, A; Westin, C F

    2001-09-01

    The vasculature is of utmost importance in neurosurgery. Direct visualization of images acquired with current imaging modalities, however, cannot provide a spatial representation of small vessels. These vessels, and their branches which show considerable variations, are most important in planning and performing neurosurgical procedures. In planning they provide information on where the lesion draws its blood supply and where it drains. During surgery the vessels serve as landmarks and guidelines to the lesion. The more minute the information is, the more precise the navigation and localization of computer guided procedures. Beyond neurosurgery and neurological study, vascular information is also crucial in cardiovascular surgery, diagnosis, and research. This paper addresses the problem of automatic segmentation of complicated curvilinear structures in three-dimensional imagery, with the primary application of segmenting vasculature in magnetic resonance angiography (MRA) images. The method presented is based on recent curve and surface evolution work in the computer vision community which models the object boundary as a manifold that evolves iteratively to minimize an energy criterion. This energy criterion is based both on intensity values in the image and on local smoothness properties of the object boundary, which is the vessel wall in this application. In particular, the method handles curves evolving in 3D, in contrast with previous work that has dealt with curves in 2D and surfaces in 3D. Results are presented on cerebral and aortic MRA data as well as lung computed tomography (CT) data.

  14. Effects of Bearing Clearance on Turbopump Stability

    NASA Technical Reports Server (NTRS)

    1985-01-01

    Effects of bearing clearances, or "dead bands," on bearing loads and rotor stability in turbopumps examined in a 194-page report. Relatively simple mathematical force model for analyzing effects highlighted. Report shows nonlinear characteristics resulting from bearing dead bands have significant effect on dynamics of turbomachinery and not ignored as in the past.

  15. 32 CFR 154.16 - Security clearance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 1 2010-07-01 2010-07-01 false Security clearance. 154.16 Section 154.16 National Defense Department of Defense OFFICE OF THE SECRETARY OF DEFENSE SECURITY DEPARTMENT OF DEFENSE PERSONNEL SECURITY PROGRAM REGULATION Personnel Security Investigative Requirements § 154.16...

  16. 32 CFR 154.16 - Security clearance.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 32 National Defense 1 2014-07-01 2014-07-01 false Security clearance. 154.16 Section 154.16 National Defense Department of Defense OFFICE OF THE SECRETARY OF DEFENSE SECURITY DEPARTMENT OF DEFENSE PERSONNEL SECURITY PROGRAM REGULATION Personnel Security Investigative Requirements § 154.16...

  17. 32 CFR 154.16 - Security clearance.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 32 National Defense 1 2012-07-01 2012-07-01 false Security clearance. 154.16 Section 154.16 National Defense Department of Defense OFFICE OF THE SECRETARY OF DEFENSE SECURITY DEPARTMENT OF DEFENSE PERSONNEL SECURITY PROGRAM REGULATION Personnel Security Investigative Requirements § 154.16...

  18. 32 CFR 154.16 - Security clearance.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 32 National Defense 1 2011-07-01 2011-07-01 false Security clearance. 154.16 Section 154.16 National Defense Department of Defense OFFICE OF THE SECRETARY OF DEFENSE SECURITY DEPARTMENT OF DEFENSE PERSONNEL SECURITY PROGRAM REGULATION Personnel Security Investigative Requirements § 154.16...

  19. 30 CFR 18.24 - Electrical clearances.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Electrical clearances. 18.24 Section 18.24 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND APPROVAL OF MINING PRODUCTS ELECTRIC MOTOR-DRIVEN MINE EQUIPMENT AND ACCESSORIES Construction and...

  20. 30 CFR 57.11010 - Stairstep clearance.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Stairstep clearance. 57.11010 Section 57.11010 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... steps shall be a minimum of seven feet, or suitable warning signs or similar devices shall be...

  1. 30 CFR 57.11010 - Stairstep clearance.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Stairstep clearance. 57.11010 Section 57.11010 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... steps shall be a minimum of seven feet, or suitable warning signs or similar devices shall be...

  2. Clearance of seborrhoeic keratoses with topical dobesilate

    PubMed Central

    Cuevas, Pedro; Angulo, Javier; Salgüero, Irene; Giménez-Gallego, Guillermo

    2012-01-01

    A patient with two seborrhoeic keratoses in the face received a single daily application of dobesilate cream during 6 months. Dobesilate achieved complete clearance of the seborrhoeic keratosis lesions with good cosmoses, suggesting that this compound is a safe and efficient candidate in the treatment of seborrhoeic keratoses. PMID:22729328

  3. Carbamazepine clearance and seizure stability during pregnancy.

    PubMed

    Johnson, Emily L; Stowe, Zachary N; Ritchie, James C; Newport, D Jeffrey; Newman, Melanee L; Knight, Bettina; Pennell, Page B

    2014-04-01

    The aims of this study were to characterize the alterations in total and free carbamazepine (CBZ) and in total and free carbamazepine-epoxide (CBZ-EPO) clearances during pregnancy, to calculate the change in free fractions of CBZ and CBZ-EPO during pregnancy, and to determine whether seizure worsening is associated with a low ratio to nonpregnant baseline concentration of total or free CBZ or CBZ-EPO. Women on CBZ were enrolled before conception or during pregnancy in this prospective, observational study. Concomitant medications and seizure frequency were recorded. Serum total and free CBZ and CBZ-EPO were collected at each visit. Changes in the clearance of all four compounds and free fractions of CBZ and CBZ-EPO were compared with nonpregnant baseline. During pregnancy, the ratios to baseline concentrations of total and free CBZ and CBZ-EPO were compared for months with and without increased seizure frequency. Total and free CBZ and CBZ-EPO clearances were calculated in 15 pregnancies in 12 women. Clearances did not change for any of these compounds during pregnancy. The free fraction of CBZ increased from 0.23 at baseline to a maximum of 0.32 in the third trimester (p=0.008). In the six women on CBZ monotherapy with adequate seizure diaries and blood sampling, seizure worsening did not correspond to a ratio to baseline concentration of less than 0.65 for total or free CBZ or CBZ-EPO. In conclusion, total and free CBZ and CBZ-EPO clearances did not change substantially during pregnancy, and seizure frequency worsening was not associated with decreased concentrations of total or free CBZ; therefore, therapeutic drug monitoring may not be necessary for all women on CBZ during pregnancy. Further studies with larger sample sizes are needed before definitive recommendations can be made. Carbamazepine monotherapy may be a relatively safe and cost effective treatment option for women with focal epilepsy syndromes during pregnancy.

  4. 19 CFR 122.26 - Entry and clearance.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... AIR COMMERCE REGULATIONS Private Aircraft § 122.26 Entry and clearance. Private aircraft, as defined... information as set forth in § 122.22(c), and grants electronic clearance via electronic mail or telephone....

  5. Mechanics of Curved Folds

    NASA Astrophysics Data System (ADS)

    Dias, Marcelo A.; Santangelo, Christian D.

    2011-03-01

    Despite an almost two thousand year history, origami, the art of folding paper, remains a challenge both artistically and scientifically. Traditionally, origami is practiced by folding along straight creases. A whole new set of shapes can be explored, however, if, instead of straight creases, one folds along arbitrary curves. We present a mechanical model for curved fold origami in which the energy of a plastically-deformed crease is balanced by the bending energy of developable regions on either side of the crease. Though geometry requires that a sheet buckle when folded along a closed curve, its shape depends on the elasticity of the sheet. NSF DMR-0846582.

  6. WWW-based data entry for document clearance requests

    SciTech Connect

    Stasiak, D.M.

    1997-10-08

    All documents created at Argonne must be cleared before being published. The clearance process is coordinated by the Publications and Record Services. The Electronic Document Review and Clearance System (EDRC) consists of a Web-based system for submission of clearance requests, an electronic staging area for document awaiting review, and Web-based review and clearance of documents. This report covers the document clearing process, the EDRC system, expected benefits/costs, and a demonstration.

  7. Role of cytochrome P4502B6 in methadone metabolism and clearance.

    PubMed

    Kharasch, Evan D; Stubbert, Kristi

    2013-03-01

    Methadone N-demethylation in vitro is catalyzed by hepatic cytochrome P4502B6 (CYP2B6) and CYP3A4, but clinical disposition is often attributed to CYP3A4. This investigation tested the hypothesis that CYP2B6 is a prominent CYP isoform responsible for clinical methadone N-demethylation and clearance, using the in vivo mechanism-based CYP2B6 inhibitor ticlopidine, given orally for 4 days. A preliminary clinical investigation with the CYP3A4/5 substrate probe alfentanil established that ticlopidine did not inhibit intestinal or hepatic CYP3A4/5. Subjects received intravenous plus oral (deuterium-labeled) racemic methadone before and after ticlopidine. Ticlopidine significantly and stereoselectively (S > R) inhibited methadone N-demethylation, decreasing plasma metabolite/methadone area under the curve ratios and metabolite formation clearances. Ticlopidine also significantly increased the dose-adjusted plasma area under the curve for R- and S-methadone by 20% and 60%, respectively, after both intravenous and oral dosing. CYP2B6 inhibition reduces methadone N-demethylation and clearance, and alters methadone concentrations, demonstrating an important role for CYP2B6 in clinical methadone disposition.

  8. Clearance and metabolism of glandular kallikrein in the rat

    SciTech Connect

    Rabito, S.F.; Seto, M.; Maitra, S.R.; Carretero, O.A.

    1985-06-01

    This study was undertaken to characterize the clearance of circulating rat glandular kallikrein and to determine the contribution of various organs and the urinary excretion to the removal of glandular kallikrein from the bloodstream. The authors injected either active /sup 125/I-kallikrein or kallikrein inactivated with phenylmethylsulfonyl fluoride (/sup 125/I-PMSF-kallikrein) intravenously into intact or nephrectomized rats and then studied the disappearance rate of trichloroacetic acid (TCA)-precipitable radioactivity from the circulation. Inactivation by PMSF markedly reduced the binding of kallikrein to plasma protease inhibitors. The removal rate of the acid-precipitable radioactivity fit a biexponential curve for both active and inactive kallikrein. In the intact rats approximately 50% of the radioactivity was removed from the circulation 30 min after the injection of active /sup 125/I-kallikrein. Removal of the kidneys did not significantly affect the clearance of active kallikrein. On the other hand, inactive /sup 125/I-PMSF-kallikrein was removed from blood faster than active /sup 125/I-kallikrein in normal animals. Approximately 50% of the radioactivity was removed from the circulation 8 min after the injection, and the half-life of inactive /sup 125/I-PMSF-kallikrein was markedly prolonged by bilateral nephrectomy. Active /sup 125/I-kallikrein was taken up by tissues, particularly the liver and the kidney. In urine, less than 2% of the radioactivity was excreted in 60 min as TCA-precipitable material. The authors concluded that glandular kallikrein is cleared rapidly from the circulation of the rat, probably in the form of a complex with a plasma protease inhibitor.

  9. 48 CFR 245.602-70 - Plant clearance procedures.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false Plant clearance procedures... Disposal 245.602-70 Plant clearance procedures. Follow the procedures at PGI 245.602-70 for establishing and processing a plant clearance case....

  10. 14 CFR 29.661 - Rotor blade clearance.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction Rotors § 29.661 Rotor blade clearance. There must be enough clearance between the rotor blades and other parts of the structure to... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Rotor blade clearance. 29.661 Section...

  11. 14 CFR 27.661 - Rotor blade clearance.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction Rotors § 27.661 Rotor blade clearance. There must be enough clearance between the rotor blades and other parts of the structure to... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Rotor blade clearance. 27.661 Section...

  12. 14 CFR 29.661 - Rotor blade clearance.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction Rotors § 29.661 Rotor blade clearance. There must be enough clearance between the rotor blades and other parts of the structure to... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Rotor blade clearance. 29.661 Section...

  13. 14 CFR 29.661 - Rotor blade clearance.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction Rotors § 29.661 Rotor blade clearance. There must be enough clearance between the rotor blades and other parts of the structure to... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Rotor blade clearance. 29.661 Section...

  14. 14 CFR 27.661 - Rotor blade clearance.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction Rotors § 27.661 Rotor blade clearance. There must be enough clearance between the rotor blades and other parts of the structure to... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Rotor blade clearance. 27.661 Section...

  15. 14 CFR 27.661 - Rotor blade clearance.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction Rotors § 27.661 Rotor blade clearance. There must be enough clearance between the rotor blades and other parts of the structure to... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Rotor blade clearance. 27.661 Section...

  16. 14 CFR 27.661 - Rotor blade clearance.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction Rotors § 27.661 Rotor blade clearance. There must be enough clearance between the rotor blades and other parts of the structure to... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Rotor blade clearance. 27.661 Section...

  17. 14 CFR 29.661 - Rotor blade clearance.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction Rotors § 29.661 Rotor blade clearance. There must be enough clearance between the rotor blades and other parts of the structure to... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Rotor blade clearance. 29.661 Section...

  18. 14 CFR 29.661 - Rotor blade clearance.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction Rotors § 29.661 Rotor blade clearance. There must be enough clearance between the rotor blades and other parts of the structure to... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Rotor blade clearance. 29.661 Section...

  19. 14 CFR 27.661 - Rotor blade clearance.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction Rotors § 27.661 Rotor blade clearance. There must be enough clearance between the rotor blades and other parts of the structure to... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Rotor blade clearance. 27.661 Section...

  20. 48 CFR 2452.237-75 - Clearance of contractor personnel.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Clearance of contractor... Clauses 2452.237-75 Clearance of contractor personnel. As prescribed in 2437.110(e), insert the following clause in solicitations and contracts. Clearance of Contractor Personnel (OCT 1999) (a) General....

  1. 32 CFR 644.69 - Title Clearance-Easements.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true Title Clearance-Easements. 644.69 Section 644.69... ESTATE HANDBOOK Acquisition Procurement of Title Evidence, Title Clearance, and Closings § 644.69 Title Clearance—Easements. (a) Easements Costing in Excess of $1,000. Curative action and clearance of title...

  2. 10 CFR 706.31 - Clearance of conciliators and arbitrators.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Clearance of conciliators and arbitrators. 706.31 Section... RELATIONS Contract Negotiation and Administration § 706.31 Clearance of conciliators and arbitrators. Conciliators and arbitrators who are regularly assigned to DOE cases may be processed for “Q” clearance at...

  3. 30 CFR 56.19104 - Clearance at shaft stations.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Clearance at shaft stations. 56.19104 Section 56.19104 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Hoisting Shafts § 56.19104 Clearance at shaft stations. Suitable clearance at shaft stations shall...

  4. 14 CFR 375.24 - Entry and clearance.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Entry and clearance. 375.24 Section 375.24 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION PROCEEDINGS) SPECIAL... Entry and clearance. All U.S. entry and clearance requirements for aircraft, passengers, crews,...

  5. 24 CFR 3285.305 - Clearance under homes.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Clearance under homes. 3285.305... URBAN DEVELOPMENT MODEL MANUFACTURED HOME INSTALLATION STANDARDS Foundations § 3285.305 Clearance under homes. A minimum clearance of 12 inches must be maintained between the lowest member of the main...

  6. 30 CFR 57.19104 - Clearance at shaft stations.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Clearance at shaft stations. 57.19104 Section 57.19104 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Hoisting Shafts § 57.19104 Clearance at shaft stations. Suitable clearance at shaft stations shall...

  7. 75 FR 70341 - Agency Information Collection Activities: Emergency Clearance Request

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-17

    ... ADMINISTRATION Agency Information Collection Activities: Emergency Clearance Request The Social Security Administration (SSA) publishes a list of information collection packages requiring clearance by the Office of... Desk Officer and SSA Reports Clearance Officer to the following addresses or fax numbers. (OMB),...

  8. 19 CFR 122.158 - Other entry and clearance requirements.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Other entry and clearance requirements. 122.158 Section 122.158 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY... clearance requirements. All other provisions of this part relating to entry and clearance of aircraft...

  9. 30 CFR 56.9103 - Clearance on adjacent tracks.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Clearance on adjacent tracks. 56.9103 Section..., Hauling, and Dumping Traffic Safety § 56.9103 Clearance on adjacent tracks. Railcars shall not be left on side tracks unless clearance is provided for traffic on adjacent tracks....

  10. 76 FR 17615 - Highway-Rail Grade Crossing; Safe Clearance

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-30

    ... Parts 177 and 392 RIN 2137-AE69 & 2126-AB04 Highway-Rail Grade Crossing; Safe Clearance AGENCY: Pipeline... that PHMSA and FMCSA extend the comment period for the Highway-Rail Grade Crossing; Safe Clearance... Crossing; Safe Clearance Notice of Proposed Rulemaking, which was published on January 28, 2011 (76 FR...

  11. 10 CFR 706.13 - Clearance of counsel.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Clearance of counsel. 706.13 Section 706.13 Energy... and Procedures in National Labor Relations Board Proceedings § 706.13 Clearance of counsel. It is recognized that clearance of counsel for the parties is sometimes desirable for proper preparation of a...

  12. 8 CFR 1280.6 - Bond to obtain clearance; form.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 8 Aliens and Nationality 1 2010-01-01 2010-01-01 false Bond to obtain clearance; form. 1280.6... IMMIGRATION REGULATIONS IMPOSITION AND COLLECTION OF FINES § 1280.6 Bond to obtain clearance; form. A bond to obtain clearance of a vessel or aircraft under section 231, 237, 239, 243, 251, 253, 254, 255, 256,...

  13. 10 CFR 95.17 - Processing facility clearance.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Processing facility clearance. 95.17 Section 95.17 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) FACILITY SECURITY CLEARANCE AND SAFEGUARDING OF NATIONAL SECURITY INFORMATION AND RESTRICTED DATA Physical Security § 95.17 Processing facility clearance....

  14. 10 CFR 95.23 - Termination of facility clearance.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Termination of facility clearance. 95.23 Section 95.23 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) FACILITY SECURITY CLEARANCE AND SAFEGUARDING OF NATIONAL SECURITY INFORMATION AND RESTRICTED DATA Physical Security § 95.23 Termination of facility clearance....

  15. 19 CFR 122.157 - Documents required for clearance.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Documents required for clearance. 122.157 Section 122.157 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT... clearance. As a condition precedent to clearance, the aircraft commander shall present to Customs: (a)...

  16. 75 FR 37518 - Agency Information Collection Activities: Emergency Clearance Request

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-29

    ... ADMINISTRATION Agency Information Collection Activities: Emergency Clearance Request The Social Security Administration (SSA) publishes a list of information collection packages requiring clearance by the Office of... Desk Officer and SSA Reports Clearance Officer to the following addresses or fax numbers. (OMB),...

  17. 8 CFR 280.6 - Bond to obtain clearance; form.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 8 Aliens and Nationality 1 2010-01-01 2010-01-01 false Bond to obtain clearance; form. 280.6 Section 280.6 Aliens and Nationality DEPARTMENT OF HOMELAND SECURITY IMMIGRATION REGULATIONS IMPOSITION AND COLLECTION OF FINES § 280.6 Bond to obtain clearance; form. A bond to obtain clearance of a...

  18. 30 CFR 57.9103 - Clearance on adjacent tracks.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Clearance on adjacent tracks. 57.9103 Section..., Hauling, and Dumping Traffic Safety § 57.9103 Clearance on adjacent tracks. Railcars shall not be left on side tracks unless clearance is provided for traffic on adjacent tracks....

  19. 14 CFR 1260.63 - Customs clearance and visas.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Customs clearance and visas. 1260.63 Section 1260.63 Aeronautics and Space NATIONAL AERONAUTICS AND SPACE ADMINISTRATION GRANTS AND COOPERATIVE AGREEMENTS General Special Conditions § 1260.63 Customs clearance and visas. Customs Clearance and Visas...

  20. 30 CFR 56.9330 - Clearance for surface equipment.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Clearance for surface equipment. 56.9330... NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Loading... Dumping Sites § 56.9330 Clearance for surface equipment. Continuous clearance of at least 30 inches...

  1. 30 CFR 57.9330 - Clearance for surface equipment.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Clearance for surface equipment. 57.9330 Section 57.9330 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Dumping Sites § 57.9330 Clearance for surface equipment. Continuous clearance of at least 30 inches...

  2. 31 CFR 205.20 - What is a clearance pattern?

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false What is a clearance pattern? 205.20 Section 205.20 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) FISCAL... Agreement § 205.20 What is a clearance pattern? States use clearance patterns to project when funds are...

  3. 30 CFR 56.9306 - Warning devices for restricted clearances.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Warning devices for restricted clearances. 56... Loading and Dumping Sites § 56.9306 Warning devices for restricted clearances. Where restricted clearance creates a hazard to persons on mobile equipment, warning devices shall be installed in advance of...

  4. 30 CFR 56.9306 - Warning devices for restricted clearances.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Warning devices for restricted clearances. 56... Loading and Dumping Sites § 56.9306 Warning devices for restricted clearances. Where restricted clearance creates a hazard to persons on mobile equipment, warning devices shall be installed in advance of...

  5. 30 CFR 56.9306 - Warning devices for restricted clearances.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Warning devices for restricted clearances. 56... Loading and Dumping Sites § 56.9306 Warning devices for restricted clearances. Where restricted clearance creates a hazard to persons on mobile equipment, warning devices shall be installed in advance of...

  6. 30 CFR 56.9306 - Warning devices for restricted clearances.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Warning devices for restricted clearances. 56... Loading and Dumping Sites § 56.9306 Warning devices for restricted clearances. Where restricted clearance creates a hazard to persons on mobile equipment, warning devices shall be installed in advance of...

  7. 48 CFR 245.602-70 - Plant clearance procedures.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 3 2012-10-01 2012-10-01 false Plant clearance procedures... Disposal 245.602-70 Plant clearance procedures. Follow the procedures at PGI 245.602-70 for establishing and processing a plant clearance case....

  8. 48 CFR 245.602-70 - Plant clearance procedures.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 3 2014-10-01 2014-10-01 false Plant clearance procedures... Disposal 245.602-70 Plant clearance procedures. Follow the procedures at PGI 245.602-70 for establishing and processing a plant clearance case....

  9. 48 CFR 245.602-70 - Plant clearance procedures.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 3 2013-10-01 2013-10-01 false Plant clearance procedures... Disposal 245.602-70 Plant clearance procedures. Follow the procedures at PGI 245.602-70 for establishing and processing a plant clearance case....

  10. 48 CFR 945.670-1 - Plant clearance function.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 5 2013-10-01 2013-10-01 false Plant clearance function... MANAGEMENT GOVERNMENT PROPERTY Reporting, Reutilization, and Disposal 945.670-1 Plant clearance function. If the plant clearance function has not been formally delegated to another Federal agency,...

  11. 48 CFR 945.670-1 - Plant clearance function.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 5 2014-10-01 2014-10-01 false Plant clearance function... MANAGEMENT GOVERNMENT PROPERTY Reporting, Reutilization, and Disposal 945.670-1 Plant clearance function. If the plant clearance function has not been formally delegated to another Federal agency,...

  12. 46 CFR 56.75-10 - Joint clearance.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 2 2014-10-01 2014-10-01 false Joint clearance. 56.75-10 Section 56.75-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Brazing § 56.75-10 Joint clearance. (a) The clearance between surfaces to be joined shall be...

  13. 46 CFR 56.75-10 - Joint clearance.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 2 2012-10-01 2012-10-01 false Joint clearance. 56.75-10 Section 56.75-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Brazing § 56.75-10 Joint clearance. (a) The clearance between surfaces to be joined shall be...

  14. 46 CFR 56.75-10 - Joint clearance.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 2 2011-10-01 2011-10-01 false Joint clearance. 56.75-10 Section 56.75-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Brazing § 56.75-10 Joint clearance. (a) The clearance between surfaces to be joined shall be...

  15. 46 CFR 56.75-10 - Joint clearance.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 2 2013-10-01 2013-10-01 false Joint clearance. 56.75-10 Section 56.75-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Brazing § 56.75-10 Joint clearance. (a) The clearance between surfaces to be joined shall be...

  16. 46 CFR 56.75-10 - Joint clearance.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Joint clearance. 56.75-10 Section 56.75-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING PIPING SYSTEMS AND APPURTENANCES Brazing § 56.75-10 Joint clearance. (a) The clearance between surfaces to be joined shall be...

  17. 10 CFR 706.13 - Clearance of counsel.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 4 2013-01-01 2013-01-01 false Clearance of counsel. 706.13 Section 706.13 Energy DEPARTMENT OF ENERGY SECURITY POLICIES AND PRACTICES RELATING TO LABOR-MANAGEMENT RELATIONS Security Policies... responsible for requesting clearance of its counsel well in advance so that clearance requirements will...

  18. Evaluation of an Active Clearance Control System Concept

    NASA Technical Reports Server (NTRS)

    Steinetz, Bruce M.; Lattime, Scott B.; Taylor, Shawn; DeCastro, Jonathan A.; Oswald, Jay; Melcher, Kevin J.

    2005-01-01

    Reducing blade tip clearances through active tip clearance control in the high pressure turbine can lead to significant reductions in emissions and specific fuel consumption as well as dramatic improvements in operating efficiency and increased service life. Current engines employ scheduled cooling of the outer case flanges to reduce high pressure turbine tip clearances during cruise conditions. These systems have relatively slow response and do not use clearance measurement, thereby forcing cold build clearances to set the minimum clearances at extreme operating conditions (e.g., takeoff, reburst) and not allowing cruise clearances to be minimized due to the possibility of throttle transients (e.g., step change in altitude). In an effort to improve upon current thermal methods, a first generation mechanically-actuated active clearance control (ACC) system has been designed and fabricated. The system utilizes independent actuators, a segmented shroud structure, and clearance measurement feedback to provide fast and precise active clearance control throughout engine operation. Ambient temperature performance tests of this first generation ACC system assessed individual seal component leakage rates and both static and dynamic overall system leakage rates. The ability of the nine electric stepper motors to control the position of the seal carriers in both open- and closed-loop control modes for single and multiple cycles was investigated. The ability of the system to follow simulated engine clearance transients in closed-loop mode showed the system was able to track clearances to within a tight tolerance ( 0.001 in. error).

  19. Evaluation of an Active Clearance Control System Concept

    NASA Technical Reports Server (NTRS)

    Steinetz, Bruce M.; Lattime, Scott B.; DeCastro, Jonathan A.; Oswald, Jay; Melcher, Kevin J.

    2005-01-01

    Reducing blade tip clearances through active tip clearance control in the high pressure turbine can lead to significant reductions in emissions and specific fuel consumption as well as dramatic improvements in operating efficiency and increased service life. Current engines employ scheduled cooling of the outer case flanges to reduce high pressure turbine tip clearances during cruise conditions. These systems have relatively slow response and do not use clearance measurement, thereby forcing cold build clearances to set the minimum clearances at extreme operating conditions (e.g., takeoff, reburst) and not allowing cruise clearances to be minimized due to the possibility of throttle transients (e.g., step change in altitude). In an effort to improve upon current thermal methods, a first generation mechanically-actuated active clearance control (ACC) system has been designed and fabricated. The system utilizes independent actuators, a segmented shroud structure, and clearance measurement feedback to provide fast and precise active clearance control throughout engine operation. Ambient temperature performance tests of this first generation ACC system assessed individual seal component leakage rates and both static and dynamic overall system leakage rates. The ability of the nine electric stepper motors to control the position of the seal carriers in both open- and closed-loop control modes for single and multiple cycles was investigated. The ability of the system to follow simulated engine clearance transients in closed-loop mode showed the system was able to track clearances to within a tight tolerance (0.001 in. error).

  20. Highly curved microchannel plates

    NASA Technical Reports Server (NTRS)

    Siegmund, O. H. W.; Cully, S.; Warren, J.; Gaines, G. A.; Priedhorsky, W.; Bloch, J.

    1990-01-01

    Several spherically curved microchannel plate (MCP) stack configurations were studied as part of an ongoing astrophysical detector development program, and as part of the development of the ALEXIS satellite payload. MCP pairs with surface radii of curvature as small as 7 cm, and diameters up to 46 mm have been evaluated. The experiments show that the gain (greater than 1.5 x 10 exp 7) and background characteristics (about 0.5 events/sq cm per sec) of highly curved MCP stacks are in general equivalent to the performance achieved with flat MCP stacks of similar configuration. However, gain variations across the curved MCP's due to variations in the channel length to diameter ratio are observed. The overall pulse height distribution of a highly curved surface MCP stack (greater than 50 percent FWHM) is thus broader than its flat counterpart (less than 30 percent). Preconditioning of curved MCP stacks gives comparable results to flat MCP stacks, but it also decreases the overall gain variations. Flat fields of curved MCP stacks have the same general characteristics as flat MCP stacks.

  1. Market Mechanism for Line Congestion Clearance

    NASA Astrophysics Data System (ADS)

    Ruiz Monroy, José Joaquín; Kita, Hiroyuki; Tanaka, Eiichi; Hasegawa, Jun

    This paper proposes a mechanism for clearance of line congestion and power flow control in a deregulated market environment. The mechanism applies penalties to the bilateral transactions that cause line congestion by increasing the prices of such transactions. The market regulates itself by redefining the transactions and checking again for violations, applying penalties if necessary and repeating the process until all the demand is satisfied without causing line congestion to the system. A bilateral transaction matrix (BTM) creation algorithm developed by the authors and a DC power flow program are integrated as parts of the market mechanism proposed in this paper. The congestion is cleared by the market participants when they reschedule their transactions. This mechanism is useful to study the effects of bilateral transactions on a power system and helps the Independent System Operator (ISO) to create rules and market mechanisms for line congestion clearance and power flow control.

  2. Clearance Kinetics and Clearance Routes of Molecules From the Suprachoroidal Space After Microneedle Injection

    PubMed Central

    Chiang, Bryce; Wang, Ke; Ethier, C. Ross; Prausnitz, Mark R.

    2017-01-01

    Purpose To determine clearance kinetics and routes of clearance of molecules from the suprachoroidal space (SCS) of live New Zealand White rabbits. Methods Suprachoroidal space collapse rate and pressure changes after microneedle injection into SCS were determined. Fluorescent fundus images were acquired to determine clearance rates of molecules ranging in size from 332 Da to 2 MDa. Microneedle injections of fluorescein were performed, and samples were taken from various sites over time to determine amount of fluorescein exiting the eye. Clearance transport was modeled theoretically and compared with experimental data. Results After injection, pressures in SCS and vitreous humor spiked and returned to baseline within 20 minutes; there was no difference between these two pressures. Suprachoroidal space collapse occurred within 40 minutes. One hour after fluorescein injection, 46% of fluorescein was still present in the eye, 15% had transported across sclera, 6% had been cleared by choroidal vasculature, and 4% had exited via leakage pathways. Characteristic clearance time increased in proportion with molecular radius, but total clearance of 2 MDa FITC-dextran was significantly slower (21 days) than smaller molecules. These data generally agreed with predictions from a theoretical model of molecular transport. Conclusions Guided by experimental data in the context of model predictions, molecular clearance from SCS occurred in three regimes: (1) on a time scale of approximately 10 minutes, fluid and molecules exited SCS by diffusion into sclera and choroid, and by pressure-driven reflux via transscleral leakage sites; (2) in approximately 1 hour, molecules cleared from choroid by blood flow; and (3) in 1 to 10 hours, molecules cleared from sclera by diffusion and convection. PMID:28125841

  3. Effect of ultrafiltration on peritoneal dialysis drug clearances.

    PubMed

    Lau, A H; Chow-Tung, E; Assadi, F K; Fornell, L; John, E

    1985-01-01

    To determine the effect of dialysate osmolarity on peritoneal dialysis drug transfer, peritoneal dialysis clearances of theophylline, phenobarbital, and tobramycin were determined in 10 rabbits using dialysate containing 1.5 and 4.25% glucose. Urea and creatinine clearances were also obtained for comparison. Under similar dialysis conditions, the peritoneal clearances of the three drugs remained unchanged for the two types of dialysate. In contrast, the peritoneal clearances of urea and creatinine were significantly higher with the use of 4.25% glucose dialysate (p less than 0.001). Thus, peritoneal dialysis clearances of theophylline, phenobarbital and tobramycin are not significantly affected by hypertonicity-induced ultrafiltration during acute peritoneal dialysis.

  4. Deposition and clearance of inhaled particles.

    PubMed Central

    Stuart, B O

    1976-01-01

    Theoretical models of respiratory tract deposition of inhaled particles are compared to experimental studies of deposition patterns in humans and animals, as determined principally by particle size, density, respiratory rate and flow parameters. Various models of inhaled particle deposition make use of convenient approximations of the respiratory tract to predict tractional deposition according to fundamental physical processes of impaction, sedimentation, and diffusion. These theoretical models for both total deposition and regional (nasopharyngeal, tracheobronchial, and pulmonary) deposition are compared with experimental studies of inhaled dusts in humans or experimental animals that have been performed in many laboratories over several decades. Reasonable correlation has been obtained between theoretical and experimental studies, but the behavior of very fine (less than 0.01 mum) particles requires further refinement.Properties of particle shape, charge, and hygroscopicity as well as the degree of respiratory tract pathology also influence deposition patterns and further experimental work is urgently needed in these areas. The influence upon deposition patterns of dynamic alterations in inspiratory flow profiles caused by a variety of breathing patterns also requires further study, and the use of such techniques with selected inhaled particle size holds promise in possible diagnostic aid in diagnosis of normal versus disease conditions. Mechanisms of conducting airway and alveolar clearance processes involving mucociliary clearance, dissolution, transport to systemic circulation, and translocation via regional lymphatic clearance are discussed. The roles of the pulmonary macrophage in airway and alveolar clearance are described, and the applicability of recent solubility models for translocation or deposited materials to liver, skeleton, or other systemic organs is discussed. PMID:797567

  5. Activating the 42d Clearance Company

    DTIC Science & Technology

    2011-12-01

    System– Enhanced. ■ Establishing supply and maintenance accounts. ■ Procuring the unit guidon . Other documents created to expedite and track the...SUBTITLE Activating the 42d Clearance Company 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR( S ) 5d. PROJECT NUMBER 5e. TASK...NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME( S ) AND ADDRESS(ES) Army Engineer School,Engineer Professional Bulletin,464 MANSCEN

  6. Army Delivers Route Clearance Vehicle Capabilities

    DTIC Science & Technology

    2010-08-01

    the Husky Vehicle-Mount- ed Mine-Detection (VMMD) System, the Buffalo® Mine- Protected Clearance Vehicle (MPCV), the Panther Medium Mine-Protected...cord (POR) RCVs—the Husky, the Buf- falo, and the Panther . POR-configured Huskys, Buffalos, and Panthers have already been fielded in-theater—albeit...IED vehicle equipped with a distinctive hydraulic arm that inter- rogates suspected explosive hazards and clears them when necessary. The Panther

  7. Reduced methadone clearance during aromatase inhibition.

    PubMed

    Lu, Wenjie Jessie; Thong, Nancy; Flockhart, David A

    2012-08-01

    Methadone is increasingly used in pain management and is a cornerstone in the treatment of opiate withdrawal. It is subject to highly variable clearance among patients. The complete metabolic disposition of methadone is likely to involve a number of enzymes, including specifically CYP2B6. Previous studies in vitro suggest that metabolism by aromatase may also contribute. Single-dose methadone pharmacokinetics (2 mg, intravenous) were studied in 15 healthy postmenopausal women in the presence and absence of a potent aromatase inhibitor, letrozole. A sequential design was used, involving a control period followed by treatment with letrozole (2.5 mg/d, 11 days), in which each subject served as her own control. On average, letrozole treatment reduced methadone systemic clearance by 22% (P = 0.001), increased methadone AUC by 23% (P = 0.007), and increased elimination half-life by 21% (P = 0.042). The plasma parent-to-metabolite ratio also increased (P = 0.009), and there was a linear relationship (R2 = 0.74) between change in this plasma ratio and change in methadone AUC0-∞. In contrast, there was no such association with change in apparent urinary methadone clearance. Letrozole did not change methadone distribution half-life or its volume of distribution. Overall, these data demonstrate a significant decrease in methadone clearance during coadministration of letrozole, consistent with decreased metabolism brought about by aromatase inhibition. An involvement of aromatase in the disposition of methadone may help explain the difficulty in methadone dosing and suggests a broader role for this catalyst of endogenous steroid metabolism in xenobiotic drug disposition.

  8. Similarity analysis of compressor tip clearance flow structure

    NASA Technical Reports Server (NTRS)

    Chen, G. T.; Greitzer, E. M.; Tan, C. S.; Marble, F. E.

    1991-01-01

    A new approach is presented for analyzing compressor tip clearance flow. The basic idea is that the clearance velocity field can be (approximately) decomposed into independent throughflow and crossflow, since chordwise pressure gradients are much smaller than normal pressure gradients in the clearance region. As in the slender body approximation in external aerodynamics, this description implies that the three-dimensional steady clearance flow can be viewed as a two-dimensional, unsteady flow. Using this approach, a similarity scaling for the crossflow in the clearance region is developed and a generalized description of the clearance vortex is derived. Calculations based on the similarity scaling agree well with a wide range of experimental data in regard to flow features such as crossflow velocity field, static pressure field, and tip clearance vortex trajectory.

  9. Deposition, retention, and clearance of inhaled particles.

    PubMed Central

    Lippmann, M; Yeates, D B; Albert, R E

    1980-01-01

    The relation between the concentrations and characteristics of air contaminants in the work place and the resultant toxic doses and potential hazards after their inhalation depends greatly on their patterns of deposition and the rates and pathways for their clearance from the deposition sites. The distribution of the deposition sites of inhaled particles is strongly dependent on their aerodynamic diameters. For normal man, inhaled non-hygroscopic particles greater than or equal to 2 micrometers that deposit in the conducting airways by impaction are concentrated on to a small fraction of the surface. Cigarette smoking and bronchitis produce a proximal shift in the deposition pattern. The major factor affecting the deposition of smaller particles is their transfer from tidal to reserve air. For particles soluble in respiratory tract fluid, systemic uptake may be relatively complete for all deposition patterns, and there may be local toxic or irritant effects or both. On the other hand, slowly soluble particles depositing in the conducting airways are carried on the surface to the glottis and are swallowed within one day. Mucociliary transport rates are highly variable, both along the ciliated airways of a given individual and between individuals. The changes in clearance rates produced by drugs, cigarette smoke, and other environmental pollutants can greatly increase or decrease these rates. Particles deposited in non-ciliated airways have large surface-to-volume ratios, and clearance by dissolution can occur for materials generally considered insoluble. They may also be cleared as free particles either by passive transport along surface liquids or, after phagocytosis, by transport within alveolar macrophages. If the particles penetrate the epithelium, either bare or within macrophages, they may be sequestered within cells or enter the lymphatic circulation and be carried to pleural, hilar, and more distant lymph nodes. Non-toxic insoluble particles are cleared from

  10. The sales learning curve.

    PubMed

    Leslie, Mark; Holloway, Charles A

    2006-01-01

    When a company launches a new product into a new market, the temptation is to immediately ramp up sales force capacity to gain customers as quickly as possible. But hiring a full sales force too early just causes the firm to burn through cash and fail to meet revenue expectations. Before it can sell an innovative product efficiently, the entire organization needs to learn how customers will acquire and use it, a process the authors call the sales learning curve. The concept of a learning curve is well understood in manufacturing. Employees transfer knowledge and experience back and forth between the production line and purchasing, manufacturing, engineering, planning, and operations. The sales learning curve unfolds similarly through the give-and-take between the company--marketing, sales, product support, and product development--and its customers. As customers adopt the product, the firm modifies both the offering and the processes associated with making and selling it. Progress along the manufacturing curve is measured by tracking cost per unit: The more a firm learns about the manufacturing process, the more efficient it becomes, and the lower the unit cost goes. Progress along the sales learning curve is measured in an analogous way: The more a company learns about the sales process, the more efficient it becomes at selling, and the higher the sales yield. As the sales yield increases, the sales learning process unfolds in three distinct phases--initiation, transition, and execution. Each phase requires a different size--and kind--of sales force and represents a different stage in a company's production, marketing, and sales strategies. Adjusting those strategies as the firm progresses along the sales learning curve allows managers to plan resource allocation more accurately, set appropriate expectations, avoid disastrous cash shortfalls, and reduce both the time and money required to turn a profit.

  11. Dynamics of curved interfaces

    SciTech Connect

    Escudero, Carlos

    2009-08-15

    Stochastic growth phenomena on curved interfaces are studied by means of stochastic partial differential equations. These are derived as counterparts of linear planar equations on a curved geometry after a reparametrization invariance principle has been applied. We examine differences and similarities with the classical planar equations. Some characteristic features are the loss of correlation through time and a particular behavior of the average fluctuations. Dependence on the metric is also explored. The diffusive model that propagates correlations ballistically in the planar situation is particularly interesting, as this propagation becomes nonuniversal in the new regime.

  12. Study on Internal Flow and External Performance of a Semi-open Impeller Centrifugal Pump with Different Tip Clearances

    NASA Astrophysics Data System (ADS)

    Jia, Xiao-Qi; Cui, Bao-Ling; Zhang, Yu-Liang; Zhu, Zu-Chao

    2015-04-01

    To study the influence of tip clearance on internal flow characteristics and external performance of a prototype centrifugal pump with a semi-open impeller, the unsteady numerical simulation and performance experiments are carried out in this paper. The evolution process of leakage vortex with time t, the flow characteristics and the magnitude of leakage rate in tip clearance are obtained in details. The results indicate that the H-Q curve hump of centrifugal pump shows a weakened trend with the increasing of tip clearance Δc. Meanwhile, the leakage rate ΔQ and the ratio of leakage rate to discharge flow rate (ψ) gradually increase. At the same tip clearance, the leakage rate ΔQ increases, while the ratio of leakage rate to discharge flow rate (ψ) decreases with the increasing of discharge flow rate Q. It is found that higher volumetric loss account for a higher percentage of the total loss at small flow rate condition. There easily exist strong leakage vortexes in the impeller inlet, impeller passage and impeller outlet. The pressure difference between suction side and pressure side makes the fluid pass through the tip clearance layer to form a lower pressure region and leakage vortex.

  13. Graphing Polar Curves

    ERIC Educational Resources Information Center

    Lawes, Jonathan F.

    2013-01-01

    Graphing polar curves typically involves a combination of three traditional techniques, all of which can be time-consuming and tedious. However, an alternative method--graphing the polar function on a rectangular plane--simplifies graphing, increases student understanding of the polar coordinate system, and reinforces graphing techniques learned…

  14. Textbook Factor Demand Curves.

    ERIC Educational Resources Information Center

    Davis, Joe C.

    1994-01-01

    Maintains that teachers and textbook graphics follow the same basic pattern in illustrating changes in demand curves when product prices increase. Asserts that the use of computer graphics will enable teachers to be more precise in their graphic presentation of price elasticity. (CFR)

  15. Curve Fit Challenge

    ERIC Educational Resources Information Center

    Harper, Suzanne R.; Driskell, Shannon

    2005-01-01

    Graphic tips for using the Geometer's Sketchpad (GSP) are described. The methods to import an image into GSP, define a coordinate system, plot points and curve fit the function using a graphical calculator are demonstrated where the graphic features of GSP allow teachers to expand the use of the technology application beyond the classroom.

  16. The Bacterial Growth Curve.

    ERIC Educational Resources Information Center

    Paulton, Richard J. L.

    1991-01-01

    A procedure that allows students to view an entire bacterial growth curve during a two- to three-hour student laboratory period is described. Observations of the lag phase, logarithmic phase, maximum stationary phase, and phase of decline are possible. A nonpathogenic, marine bacterium is used in the investigation. (KR)

  17. Tip Clearance Control Using Plasma Actuators

    DTIC Science & Technology

    2007-03-01

    Clearance Control Using Plasma Actuators 4 posed by Denton (1993). A number of investigators have used partial shrouds, or " winglet " designs to...main molded blade with a span of 3.42 in., a removable molded blade segment with a span of 0.1875 in., and removable blade tip winglets made of glass...segment and the main blade to vary the distance between the blade end and the front wall of the cascade section. The winglets were machined using a

  18. Statistical Tolerance and Clearance Analysis for Assembly

    NASA Technical Reports Server (NTRS)

    Lee, S.; Yi, C.

    1996-01-01

    Tolerance is inevitable because manufacturing exactly equal parts is known to be impossible. Furthermore, the specification of tolerances is an integral part of product design since tolerances directly affect the assemblability, functionality, manufacturability, and cost effectiveness of a product. In this paper, we present statistical tolerance and clearance analysis for the assembly. Our proposed work is expected to make the following contributions: (i) to help the designers to evaluate products for assemblability, (ii) to provide a new perspective to tolerance problems, and (iii) to provide a tolerance analysis tool which can be incorporated into a CAD or solid modeling system.

  19. Dynamics analysis of space robot manipulator with joint clearance

    NASA Astrophysics Data System (ADS)

    Zhao, Yang; Bai, Zheng Feng

    2011-04-01

    A computational methodology for analysis of space robot manipulator systems, considering the effects of the clearances in the joint, is presented. The contact dynamics model in joint clearance is established using the nonlinear equivalent spring-damp model and the friction effect is considered using the Coulomb friction model. The space robot system dynamic equation of manipulator with clearance is established. Then the dynamics simulation is presented and the dynamics characteristics of robot manipulator with clearance are analyzed. This work provides a practical method to analyze the dynamics characteristics of space robot manipulator with joint clearance and improves the engineering application. The computational methodology can predict the effects of clearance on space robot manipulator preferably, which is the basis of space robot manipulator design, precision analysis and ground test.

  20. Study of blade clearance effects on centrifugal pumps

    NASA Technical Reports Server (NTRS)

    Hoshide, R. K.; Nielson, C. E.

    1972-01-01

    A program of analysis, design, fabrication, and testing has been conducted to develop and experimentally verify analytical models to predict the effects of impeller blade clearance on centrifugal pumps. The effect of tip clearance on pump efficiency, and the relationship between the head coefficient and torque loss with tip clearance was established. Analysis were performed to determine the cost variation in design, manufacture, and test that would occur between unshrouded and shrouded impellers. An impeller, representative of typical rocket engine impellers, was modified by removing its front shroud to permit variation of its blade clearances. It was tested in water with special instrumentation to provide measurements of blade surface pressures during operation. Pump performance data were obtained from tests at various impeller tip clearances. Blade pressure data were obtained at the nominal tip clearance. Comparisons of predicted and measured data are given.

  1. Numerical investigation of hub clearance flow in a Kaplan turbine

    NASA Astrophysics Data System (ADS)

    Wu, H.; Feng, J. J.; Wu, G. K.; Luo, X. Q.

    2012-11-01

    In this paper, the flow field considering the hub clearance flow in a Kaplan turbine has been investigated through using the commercial CFD code ANSYS CFX based on high-quality structured grids generated by ANSYS ICEM CFD. The turbulence is simulated by k-ω based shear stress transport (SST) turbulence model together with automatic near wall treatments. Four kinds of simulations have been conducted for the runner geometry without hub clearance, with only the hub front clearance, with only the rear hub clearance, and with both front and rear clearance. The analysis of the obtained results is focused on the flow structure of the hub clearance flow, the effect on the turbine performance including hydraulic efficiency and cavitation performance, which can improve the understanding on the flow field in a Kaplan turbine.

  2. Reduction of hepatic insulin clearance after oral glucose ingestion is not mediated by glucagon-like peptide 1 or gastric inhibitory polypeptide in humans.

    PubMed

    Meier, Juris J; Holst, Jens J; Schmidt, Wolfgang E; Nauck, Michael A

    2007-09-01

    Changes in hepatic insulin clearance can occur after oral glucose or meal ingestion. This has been attributed to the secretion and action of gastric inhibitory polypeptide (GIP) and glucagon-like peptide (GLP)-1. Given the recent availability of drugs based on incretin hormones, such clearance effects may be important for the future treatment of type 2 diabetes. Therefore, we determined insulin clearance in response to endogenously secreted and exogenously administered GIP and GLP-1. Insulin clearance was estimated from the molar C-peptide-to-insulin ratio calculated at basal conditions and from the respective areas under the curve after glucose, GIP, or GLP-1 administration. Oral glucose administration led to an approximately 60% reduction in the C-peptide-to-insulin ratio (P < 0.0001), whereas intravenous glucose administration had no effect (P = 0.09). The endogenous secretion of GIP or GLP-1 was unrelated to the changes in insulin clearance. The C-peptide-to-insulin ratio was unchanged after the intravenous administration of GIP or GLP-1 in the fasting state (P = 0.27 and P = 0.35, respectively). Likewise, infusing GLP-1 during a meal course did not alter insulin clearance (P = 0.87). An inverse nonlinear relationship was found between the C-peptide-to-insulin ratio and the integrated insulin levels after oral and during intravenous glucose administration. Insulin clearance is reduced by oral but not by intravenous glucose administration. Neither GIP nor GLP-1 has significant effects on insulin extraction. An inverse relationship between insulin concentrations and insulin clearance suggests that the secretion of insulin itself determines the rate of hepatic insulin clearance.

  3. Trishear for curved faults

    NASA Astrophysics Data System (ADS)

    Brandenburg, J. P.

    2013-08-01

    Fault-propagation folds form an important trapping element in both onshore and offshore fold-thrust belts, and as such benefit from reliable interpretation. Building an accurate geologic interpretation of such structures requires palinspastic restorations, which are made more challenging by the interplay between folding and faulting. Trishear (Erslev, 1991; Allmendinger, 1998) is a useful tool to unravel this relationship kinematically, but is limited by a restriction to planar fault geometries, or at least planar fault segments. Here, new methods are presented for trishear along continuously curved reverse faults defining a flat-ramp transition. In these methods, rotation of the hanging wall above a curved fault is coupled to translation along a horizontal detachment. Including hanging wall rotation allows for investigation of structures with progressive backlimb rotation. Application of the new algorithms are shown for two fault-propagation fold structures: the Turner Valley Anticline in Southwestern Alberta, and the Alpha Structure in the Niger Delta.

  4. Atlas of fatigue curves

    SciTech Connect

    Boyer, H.E.

    1986-01-01

    This Atlas was developed to serve engineers who are looking for fatigue data on a particular metal or alloy. Having these curves compiled in a single book will also facilitate the computerization of the involved data. It is pointed out that plans are under way to make the data in this book available in ASCII files for analysis by computer programs. S-N curves which typify effects of major variables are considered along with low-carbon steels, medium-carbon steels, alloy steels, HSLA steels, high-strength alloy steels, heat-resisting steels, stainless steels, maraging steels, cast irons, and heat-resisting alloys. Attention is also given to aluminum alloys, copper alloys, magnesium alloys, molybdenum, tin alloys, titanium and titanium alloys, zirconium, steel castings, closed-die forgings, powder metallurgy parts, composites, effects of surface treatments, and test results for component parts.

  5. Mouse Curve Biometrics

    SciTech Connect

    Schulz, Douglas A.

    2007-10-08

    A biometric system suitable for validating user identity using only mouse movements and no specialized equipment is presented. Mouse curves (mouse movements with little or no pause between them) are individually classied and used to develop classication histograms, which are representative of an individual's typical mouse use. These classication histograms can then be compared to validate identity. This classication approach is suitable for providing continuous identity validation during an entire user session.

  6. Measuring foot placement and clearance during stair descent.

    PubMed

    Muhaidat, Jennifer; Kerr, Andrew; Rafferty, Danny; Skelton, Dawn A; Evans, Jonathan J

    2011-03-01

    Falls during stair descent are a serious problem and can lead to accidental death. Inappropriate foot placement on, and clearance over, steps have been identified as causes for falls on stairs. This study investigated a new method for measuring placement and clearance during stair descent in 10 healthy young subjects. The effect of foot length was accounted for during the measurement of foot placement by calculating the percentage length of the foot overhanging the step. Foot clearance was measured as the resultant of the minimum vertical and horizontal distances from the heel of the foot to the edge of the step. Clearance was divided into landing and passing clearance depending on the planned placement of the foot in relation to the step edge being cleared. Each subject performed seven trials of stairs descent. Mean (SD) and CV (SD) were 16% (6), 0.28 (0.15) for placement; 45.88 (10.05), 0.21 (0.07) for landing clearance; 107.25 (5.59), 0.25 (0.08) for passing clearance. There was no statistically significant effect of trial on placement and clearance (p>0.05). There was a significant effect of step number on landing and passing clearance (p=0.01, p<0.001 respectively). Landing and passing clearances were greater for the third step compared to the second step. Passing clearance was also significantly greater than landing clearance (p<0.001). The repeatable methods and findings from this study might be useful in providing a technical background and normal values for the design of future gait studies on stairs.

  7. Quantization on Curves

    NASA Astrophysics Data System (ADS)

    Frønsdal, Christian; Kontsevich, Maxim

    2007-02-01

    Deformation quantization on varieties with singularities offers perspectives that are not found on manifolds. The Harrison component of Hochschild cohomology, vanishing on smooth manifolds, reflects information about singularities. The Harrison 2-cochains are symmetric and are interpreted in terms of abelian *-products. This paper begins a study of abelian quantization on plane curves over mathbb{C}, being algebraic varieties of the form {mathbb{C}}^2/R, where R is a polynomial in two variables; that is, abelian deformations of the coordinate algebra mathbb{C}[x,y]/(R). To understand the connection between the singularities of a variety and cohomology we determine the algebraic Hochschild (co)homology and its Barr Gerstenhaber Schack decomposition. Homology is the same for all plane curves mathbb{C}[x,y]/R, but the cohomology depends on the local algebra of the singularity of R at the origin. The Appendix, by Maxim Kontsevich, explains in modern mathematical language a way to calculate Hochschild and Harrison cohomology groups for algebras of functions on singular planar curves etc. based on Koszul resolutions.

  8. Faster non-renal clearance of metoprolol in streptozotocin-induced diabetes mellitus rats.

    PubMed

    Lee, Unji; Lee, Inchul; Lee, Byung K; Kang, Hee E

    2013-11-20

    Metoprolol is a selective β1-adrenergic receptor antagonist metabolized by hepatic cytochrome P450s (CYPs). In this study, we evaluated pharmacokinetic changes following intravenous (i.v.) and oral metoprolol in rats with diabetes mellitus induced by streptozotocin (DMIS). Metoprolol has an intermediate hepatic extraction ratio in rats (0.586-0.617), and it is assumed that the liver is exclusively responsible for metoprolol metabolism. Thus, the hepatic clearance, CL(H) (the non-renal clearance, CL(NR)) of metoprolol depends on the hepatic blood flow rate (Q(H)), the free fraction in plasma (f(p)), and in vitro hepatic intrinsic clearance, CL(int). After i.v. administration of 1.5 mg/kg metoprolol to DMIS rats, its CLNR was 40.9% faster than control animals. This could be due to a significantly faster QH because hepatic CL(int) and fp were comparable between the two groups of rats due to unchanged hepatic CYP2D activity. After oral administration of 1.5 mg/kg metoprolol to DMIS rats, gastrointestinal absorption was >99% of the oral dose for both groups, while the area under the curve (AUC) was 27.9% smaller, which could be caused by the greater hepatic metabolism seen in the i.v. study. These findings have potential therapeutic implications, assuming that the DMIS rats qualitatively reflect similar changes in patients with diabetes.

  9. Scintigraphic monitoring of mucociliary tracheo-bronchial clearance of technetium-99m macroaggregated albumin aerosol

    SciTech Connect

    Zwas, S.T.; Katz, I.; Belfer, B.; Baum, G.L.; Aharonson, E.

    1987-02-01

    A simple method for in vivo monitoring mucociliary tracheo-bronchial clearance is described. Eighteen healthy subjects and 13 patients with various chronic lung diseases were studied by this method. The principle of using an aerosol administration system similar to the system used for routine ventilation lung studies is stressed. Proximal large airway deposition of the radioaerosol was obtained by using relatively large particles (average diameter 2 microM) of (99mTc)MAA aerosol. Monitoring was performed by visual inspection of the tracheo-bronchial cinescintigraphic ascendence of the accumulated radioactive boli and by assessing their rate of clearance via automated computer analysis of the time-activity curves, following the movement of each bolus. The normal mean +/- s.d. clearance rate thus obtained was 4.7 +/- 1.3 mm/min. This rate appears to be more precise as compared with the range of results obtained by other radioisotopic methods. Significantly faster rates, mean 8.2 +/- 1.4 mm/min (p less than 0.001) were obtained in bronchiectatic patients while slower rates (2.8 mm/min) were seen in a patient with ciliary dyskinesia.

  10. Deposition and clearance of inhaled particles.

    PubMed Central

    Stuart, B O

    1984-01-01

    Theoretical models of respiratory tract deposition of inhaled particles are compared to experimental studies of deposition patterns in humans and animals, as governed principally by particle size, density, respiratory rate and flow parameters. Various models of inhaled particle deposition make use of approximations of the respiratory tract to predict fractional deposition caused by fundamental physical processes of particle impaction, sedimentation, and diffusion. These models for both total deposition and regional (nasopharyngeal, tracheobronchial, and pulmonary) deposition are compared with early and recent experimental studies. Reasonable correlation has been obtained between theoretical and experimental studies, but the behavior in the respiratory tract of very fine (less than 0.1 micron) particles requires further investigation. Properties of particle shape, charge and hygroscopicity as well as the degree of respiratory tract pathology also influence deposition patterns; definitive experimental work is needed in these areas. The influence upon deposition patterns of dynamic alterations in inspiratory flow profiles caused by a variety of breathing patterns also requires further study, and the use of differing ventilation techniques with selected inhaled particle sizes holds promise in diagnosis of respiratory tract diseases. Mechanisms of conducting airway and alveolar clearance processes involving the pulmonary macrophage, mucociliary clearance, dissolution, transport to systemic circulation, and translocation via regional lymphatic vessels are discussed. PMID:6376108

  11. Application of clearance automatic laser inspection system to clearance measurement of concrete waste

    SciTech Connect

    Sasaki, Michiya; Ogino, Haruyuki; Hattori, Takatoshi

    2007-07-01

    Recently, the Clearance Automatic Laser Inspection System (CLALIS) has been developed for the clearance measurement of metal scraps. It utilizes three-dimensional (3D) laser scanning, y-ray measurement and Monte Carlo calculation, and has outstanding detection ability. For the clearance measurement of concrete segments, the effect of background (BG) gamma rays from natural radionuclides in the measurement target, such as K-40 and the radioactive decay products of Th-232 and U-238, should be compensated for to ensure adequate waste management. Since NE102A plastic scintillation detectors are used for y-ray measurement in CLALIS, it is impossible to distinguish between count rates of natural radionuclides and contaminants on the basis of gamma-ray energy information. To apply CLALIS to the clearance measurement of concrete segments, the original activity evaluation method was improved by adding a new compensation procedure. In this procedure, BG count rate due to natural radionuclides is estimated by a Monte Carlo calculation with pre-analyzed data of a representative sample of the measurement target. The activity concentration of natural radionuclides in concrete differs markedly depending on the production location of its components, such as cement and aggregates. In this study, using six mock concrete waste samples, which were composed of cement and fine aggregate from various production locations, the accuracy of BG compensation was experimentally estimated. In addition, the accuracy of calibration for concrete waste was also estimated using a number of mock concrete segments of small and large triangular prisms. By considering the uncertainties of BG compensation and calibration, the detection limit of CLALIS for concrete waste was estimated. As a result, it was revealed that CLALIS could be applied to the clearance measurement of concrete segments when the mass of the measurement target is greater than approximately 1.1 kg and the key radionuclide is Co-60

  12. Fuel conservation through active control of rotor clearances

    NASA Technical Reports Server (NTRS)

    Beitler, R. S.; Saunders, A. A.; Wanger, R. P.

    1980-01-01

    Under the NASA-sponsored Energy Efficient Engine (EEE) Project, technology is being developed which will significantly reduce the fuel consumption of turbofan engines for subsonic transport aircraft. One technology concept being pursued is active control of rotor tip clearances. Attention is given to rotor tip clearance considerations and an overview of preliminary study results as well as the General Electric EEE clearance control approach is presented. Finally, potential fuel savings with active control of rotor clearances for a typical EEE mission are predicted.

  13. ESR measurement of radical clearance in lung of whole mouse

    SciTech Connect

    Takeshita, K.; Utsumi, H.; Hamada, A. )

    1991-06-14

    Clearance of the nitroxide radicals, hydroxy-TEMPO and carboxy-PROxYL, in whole-mouse lung was directly measured by in vivo ESR. After injecting a nitroxide radical, distribution of the nitroxide radical all over the lung was confirmed by ESR imaging. The ESR signal of hydroxy-TEMPO was reduced in the lung and the clearance obeyed first-order kinetics, whereas the signal of carboxy-PROxYL remained constant. Comparison of the clearance rates of live and dead mice indicated the presence of 2 different clearance systems in the lung: loss of its paramagnetism in the lung, and transfer from alveolar to the blood circulation system.

  14. Rotation Curves of Galaxies

    NASA Astrophysics Data System (ADS)

    Kalnajs, Agris J.

    One can obtain a fairly good understanding of the relation between axially symmetric mass distributions and the rotation curves they produce without resorting to calculations. However it does require a break with tradition. The first step consists of replacing quantities such as surface density, volume density, and circular velocity with the mass in a ring, mass in a spherical shell, and the square of the circular velocity, or more precisely with 2 pi G r mu(r), 4 pi G r^2 rho(r), and Vc^2 (r). These three quantities all have the same dimensions, and are related to each other by scale-free linear operators. The second step consists of introducing ln(r) as the coordinate. On the log scale the scale-free operators becomes the more familiar convolution operations. Convolutions are easily handled by Fourier techniques and a surface density can be converted into a rotation curve or volume density in a small fraction of a second. A simple plot of 2 pi G r mu(r) as a function of ln(r) reveals the relative contributions of different radii to Vc^2(r). Such a plot also constitutes a sanity test for the fitting of various laws to photometric data. There are numerous examples in the literature of excellent fits to the tails that lack data or are poor fits around the maximum of 2 pi G r mu(r). I will discuss some exact relations between the above three quantities as well as some empirical observations such as the near equality of the maxima of 2 pi G r mu(r) and Vc^2 (r) curves for flat mass distributions.

  15. Curved PVDF airborne transducer.

    PubMed

    Wang, H; Toda, M

    1999-01-01

    In the application of airborne ultrasonic ranging measurement, a partially cylindrical (curved) PVDF transducer can effectively couple ultrasound into the air and generate strong sound pressure. Because of its geometrical features, the ultrasound beam angles of a curved PVDF transducer can be unsymmetrical (i.e., broad horizontally and narrow vertically). This feature is desired in some applications. In this work, a curved PVDF air transducer is investigated both theoretically and experimentally. Two resonances were observed in this transducer. They are length extensional mode and flexural bending mode. Surface vibration profiles of these two modes were measured by a laser vibrometer. It was found from the experiment that the surface vibration was not uniform along the curvature direction for both vibration modes. Theoretical calculations based on a model developed in this work confirmed the experimental results. Two displacement peaks were found in the piezoelectric active direction of PVDF film for the length extensional mode; three peaks were found for the flexural bending mode. The observed peak positions were in good agreement with the calculation results. Transient surface displacement measurements revealed that vibration peaks were in phase for the length extensional mode and out of phase for the flexural bending mode. Therefore, the length extensional mode can generate a stronger ultrasound wave than the flexural bending mode. The resonance frequencies and vibration amplitudes of the two modes strongly depend on the structure parameters as well as the material properties. For the transducer design, the theoretical model developed in this work can be used to optimize the ultrasound performance.

  16. Magnetism in curved geometries

    NASA Astrophysics Data System (ADS)

    Streubel, Robert; Fischer, Peter; Kronast, Florian; Kravchuk, Volodymyr P.; Sheka, Denis D.; Gaididei, Yuri; Schmidt, Oliver G.; Makarov, Denys

    2016-09-01

    Extending planar two-dimensional structures into the three-dimensional space has become a general trend in multiple disciplines, including electronics, photonics, plasmonics and magnetics. This approach provides means to modify conventional or to launch novel functionalities by tailoring the geometry of an object, e.g. its local curvature. In a generic electronic system, curvature results in the appearance of scalar and vector geometric potentials inducing anisotropic and chiral effects. In the specific case of magnetism, even in the simplest case of a curved anisotropic Heisenberg magnet, the curvilinear geometry manifests two exchange-driven interactions, namely effective anisotropy and antisymmetric exchange, i.e. Dzyaloshinskii-Moriya-like interaction. As a consequence, a family of novel curvature-driven effects emerges, which includes magnetochiral effects and topologically induced magnetization patterning, resulting in theoretically predicted unlimited domain wall velocities, chirality symmetry breaking and Cherenkov-like effects for magnons. The broad range of altered physical properties makes these curved architectures appealing in view of fundamental research on e.g. skyrmionic systems, magnonic crystals or exotic spin configurations. In addition to these rich physics, the application potential of three-dimensionally shaped objects is currently being explored as magnetic field sensorics for magnetofluidic applications, spin-wave filters, advanced magneto-encephalography devices for diagnosis of epilepsy or for energy-efficient racetrack memory devices. These recent developments ranging from theoretical predictions over fabrication of three-dimensionally curved magnetic thin films, hollow cylinders or wires, to their characterization using integral means as well as the development of advanced tomography approaches are in the focus of this review.

  17. Magnetism in curved geometries

    SciTech Connect

    Streubel, Robert; Fischer, Peter; Kronast, Florian; Kravchuk, Volodymyr P.; Sheka, Denis D.; Gaididei, Yuri; Schmidt, Oliver G.; Makarov, Denys

    2016-08-17

    Extending planar two-dimensional structures into the three-dimensional space has become a general trend in multiple disciplines, including electronics, photonics, plasmonics and magnetics. This approach provides means to modify conventional or to launch novel functionalities by tailoring the geometry of an object, e.g. its local curvature. In a generic electronic system, curvature results in the appearance of scalar and vector geometric potentials inducing anisotropic and chiral effects. In the specific case of magnetism, even in the simplest case of a curved anisotropic Heisenberg magnet, the curvilinear geometry manifests two exchange-driven interactions, namely effective anisotropy and antisymmetric exchange, i.e. Dzyaloshinskii–Moriya-like interaction. As a consequence, a family of novel curvature-driven effects emerges, which includes magnetochiral effects and topologically induced magnetization patterning, resulting in theoretically predicted unlimited domain wall velocities, chirality symmetry breaking and Cherenkov-like effects for magnons. The broad range of altered physical properties makes these curved architectures appealing in view of fundamental research on e.g. skyrmionic systems, magnonic crystals or exotic spin configurations. In addition to these rich physics, the application potential of three-dimensionally shaped objects is currently being explored as magnetic field sensorics for magnetofluidic applications, spin-wave filters, advanced magneto-encephalography devices for diagnosis of epilepsy or for energy-efficient racetrack memory devices. Finally, these recent developments ranging from theoretical predictions over fabrication of three-dimensionally curved magnetic thin films, hollow cylinders or wires, to their characterization using integral means as well as the development of advanced tomography approaches are in the focus of this review.

  18. Magnetism in curved geometries

    DOE PAGES

    Streubel, Robert; Fischer, Peter; Kronast, Florian; ...

    2016-08-17

    Extending planar two-dimensional structures into the three-dimensional space has become a general trend in multiple disciplines, including electronics, photonics, plasmonics and magnetics. This approach provides means to modify conventional or to launch novel functionalities by tailoring the geometry of an object, e.g. its local curvature. In a generic electronic system, curvature results in the appearance of scalar and vector geometric potentials inducing anisotropic and chiral effects. In the specific case of magnetism, even in the simplest case of a curved anisotropic Heisenberg magnet, the curvilinear geometry manifests two exchange-driven interactions, namely effective anisotropy and antisymmetric exchange, i.e. Dzyaloshinskii–Moriya-like interaction. Asmore » a consequence, a family of novel curvature-driven effects emerges, which includes magnetochiral effects and topologically induced magnetization patterning, resulting in theoretically predicted unlimited domain wall velocities, chirality symmetry breaking and Cherenkov-like effects for magnons. The broad range of altered physical properties makes these curved architectures appealing in view of fundamental research on e.g. skyrmionic systems, magnonic crystals or exotic spin configurations. In addition to these rich physics, the application potential of three-dimensionally shaped objects is currently being explored as magnetic field sensorics for magnetofluidic applications, spin-wave filters, advanced magneto-encephalography devices for diagnosis of epilepsy or for energy-efficient racetrack memory devices. Finally, these recent developments ranging from theoretical predictions over fabrication of three-dimensionally curved magnetic thin films, hollow cylinders or wires, to their characterization using integral means as well as the development of advanced tomography approaches are in the focus of this review.« less

  19. Complementary Curves of Descent

    DTIC Science & Technology

    2012-11-16

    provision of law , no person shall be subject to a penalty for failing to comply with a collection of information if it does not display a currently valid...curves of descent 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR( S ) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT...NUMBER 7. PERFORMING ORGANIZATION NAME( S ) AND ADDRESS(ES) US Naval Academy,Physics Department,Annapolis,MD,21402-1363 8. PERFORMING ORGANIZATION

  20. Curved cap corrugated sheet

    NASA Technical Reports Server (NTRS)

    Davis, R. C.; Bales, T. T.; Royster, D. M.; Jackson, L. R. (Inventor)

    1984-01-01

    The report describes a structure for a strong, lightweight corrugated sheet. The sheet is planar or curved and includes a plurality of corrugation segments, each segment being comprised of a generally U-shaped corrugation with a part-cylindrical crown and cap strip, and straight side walls and with secondary corrugations oriented at right angles to said side walls. The cap strip is bonded to the crown and the longitudinal edge of said cap strip extends beyond edge at the intersection between said crown and said side walls. The high strength relative to weight of the structure makes it desirable for use in aircraft or spacecraft.

  1. Transforming Curves into Curves with the Same Shape.

    ERIC Educational Resources Information Center

    Levine, Michael V.

    Curves are considered to have the same shape when they are related by a similarity transformation of a certain kind. This paper extends earlier work on parallel curves to curves with the same shape. Some examples are given more or less explicitly. A generalization is used to show that the theory is ordinal and to show how the theory may be applied…

  2. Perioperative Non-Invasive Indocyanine Green-Clearance Testing to Predict Postoperative Outcome after Liver Resection

    PubMed Central

    Haegele, Stefanie; Reiter, Silvia; Wanek, David; Offensperger, Florian; Pereyra, David; Stremitzer, Stefan; Fleischmann, Edith; Brostjan, Christine; Gruenberger, Thomas; Starlinger, Patrick

    2016-01-01

    Background Postoperative liver dysfunction may lead to morbidity and mortality after liver resection. Preoperative liver function assessment is critical to identify preexisting liver dysfunction in patients prior to resection. The aim of this study was to evaluate the predictive potential of perioperative indocyanine green (ICG)-clearance testing to prevent postoperative liver dysfunction and morbidity using standardized outcome parameters in a routine Western-clinical-setting. Study Design 137 patients undergoing partial hepatectomy between 2011 and 2013, at the general hospital of Vienna, were included. ICG-clearance was recorded one day prior to surgery as well as on the first and fifth postoperative day. Postoperative liver dysfunction was defined according to the International Study Group of Liver Surgery and evaluation of morbidity was based on the Dindo-Clavien classification. Statistical analyses were based on non-parametric tests. Results Preoperative reduced ICG—plasma disappearance rate (PDR) as well as increased ICG—retention rate at 15 min (R15) were able to significantly predict postoperative liver dysfunction (Area under the curve = PDR: 0.716, P = 0.018; R15: 0.719, P = 0.016). Furthermore, PDR <17%/min. or R15 >8%, were able to accurately predict postoperative complications prior to surgery. In addition to this, ICG-clearance on postoperative day 1 comparably predicted postoperative liver dysfunction (Area under the curve = PDR: 0.895; R15: 0.893; both P <0.001), specifically, PDR <10%/min or R15 >20% on postoperative day 1 predicted poor postoperative outcome. Conclusion PDR and R15 may represent useful parameters to distinguish preoperative high and low risk patients in a Western collective as well as on postoperative day 1, to identify patients who require closer monitoring for potential complications. PMID:27812143

  3. Validation of Dose Calculation Codes for Clearance

    SciTech Connect

    Menon, S.; Wirendal, B.; Bjerler, J.; Studsvik; Teunckens, L.

    2003-02-27

    Various international and national bodies such as the International Atomic Energy Agency, the European Commission, the US Nuclear Regulatory Commission have put forward proposals or guidance documents to regulate the ''clearance'' from regulatory control of very low level radioactive material, in order to allow its recycling as a material management practice. All these proposals are based on predicted scenarios for subsequent utilization of the released materials. The calculation models used in these scenarios tend to utilize conservative data regarding exposure times and dose uptake as well as other assumptions as a safeguard against uncertainties. None of these models has ever been validated by comparison with the actual real life practice of recycling. An international project was organized in order to validate some of the assumptions made in these calculation models, and, thereby, better assess the radiological consequences of recycling on a practical large scale.

  4. Improved Flight Test Procedures for Flutter Clearance

    NASA Technical Reports Server (NTRS)

    Lind, Rick C.; Brenner, Martin J.; Freudinger, Lawrence C.

    1997-01-01

    Flight flutter testing is an integral part of flight envelope clearance. This paper discusses advancements in several areas that are being investigated to improve efficiency and safety of flight test programs. Results are presented from recent flight testing of the F/A-18 Systems Research Aircraft. A wingtip excitation system was used to generate aeroelastic response data. This system worked well for many flight conditions but still displayed some anomalies. Wavelet processing is used to analyze the flight data. Filtered transfer functions are generated that greatly improve system identification. A flutter margin is formulated that accounts for errors between a model and flight data. Worst-case flutter margins are computed to demonstrate the flutter boundary may lie closer to the flight envelope than previously estimated. This paper concludes with developments for a distributed flight analysis environment and on-line health monitoring.

  5. [Mucociliary clearance function and medicamentous modification].

    PubMed

    Konrad, F

    1996-09-01

    Mucociliary clearance represents a complex self-cleaning mechanism of the lung and is based on the functional unity of ciliated columnar cells and the special viscoelastic properties of the secretion produced in the tracheobronchial system. It has been known for a long time that intubation and mechanical ventilation can impair mucous transport and lead to morphological damage to the tracheobronchial mucosa. Recent studies made it clear, however, that mechanical ventilation during anaesthesia using an appropriate anaesthesiological technique has no deleterious effect on mucus transport in patients with healthy lungs. Ventilated patients in the intensive-care unit frequently have impaired mucus transport, which is associated with the development of retention of secretion and nosocomial pneumonia. In these patients a number of factors combine to form a formidable potential insult to the mucociliary transport mechanism. Numerous drugs can affect mucociliary transport. Beta-mimetics and theophylline, in particular, have a favourable effect on mucociliary transport, whereas the effect of mucolytic agents is controversial.

  6. Anthrax edema toxin impairs clearance in mice.

    PubMed

    Sastalla, Inka; Tang, Shixing; Crown, Devorah; Liu, Shihui; Eckhaus, Michael A; Hewlett, Indira K; Leppla, Stephen H; Moayeri, Mahtab

    2012-02-01

    The anthrax edema toxin (ET) of Bacillus anthracis is composed of the receptor-binding component protective antigen (PA) and of the adenylyl cyclase catalytic moiety, edema factor (EF). Uptake of ET into cells raises intracellular concentrations of the secondary messenger cyclic AMP, thereby impairing or activating host cell functions. We report here on a new consequence of ET action in vivo. We show that in mouse models of toxemia and infection, serum PA concentrations were significantly higher in the presence of enzymatically active EF. These higher concentrations were not caused by ET-induced inhibition of PA endocytosis; on the contrary, ET induced increased PA binding and uptake of the PA oligomer in vitro and in vivo through upregulation of the PA receptors TEM8 and CMG2 in both myeloid and nonmyeloid cells. ET effects on protein clearance from circulation appeared to be global and were not limited to PA. ET also impaired the clearance of ovalbumin, green fluorescent protein, and EF itself, as well as the small molecule biotin when these molecules were coinjected with the toxin. Effects on injected protein levels were not a result of general increase in protein concentrations due to fluid loss. Functional markers for liver and kidney were altered in response to ET. Concomitantly, ET caused phosphorylation and activation of the aquaporin-2 water channel present in the principal cells of the collecting ducts of the kidneys that are responsible for fluid homeostasis. Our data suggest that in vivo, ET alters circulatory protein and small molecule pharmacokinetics by an as-yet-undefined mechanism, thereby potentially allowing a prolonged circulation of anthrax virulence factors such as EF during infection.

  7. 14 CFR 29.411 - Ground clearance: tail rotor guard.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Ground clearance: tail rotor guard. 29.411 Section 29.411 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... System Loads § 29.411 Ground clearance: tail rotor guard. (a) It must be impossible for the tail rotor...

  8. 14 CFR 29.411 - Ground clearance: tail rotor guard.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Ground clearance: tail rotor guard. 29.411 Section 29.411 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... System Loads § 29.411 Ground clearance: tail rotor guard. (a) It must be impossible for the tail rotor...

  9. 14 CFR 29.411 - Ground clearance: tail rotor guard.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Ground clearance: tail rotor guard. 29.411 Section 29.411 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... System Loads § 29.411 Ground clearance: tail rotor guard. (a) It must be impossible for the tail rotor...

  10. 14 CFR 27.411 - Ground clearance: tail rotor guard.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Ground clearance: tail rotor guard. 27.411 Section 27.411 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... System Loads § 27.411 Ground clearance: tail rotor guard. (a) It must be impossible for the tail rotor...

  11. 14 CFR 27.411 - Ground clearance: tail rotor guard.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Ground clearance: tail rotor guard. 27.411 Section 27.411 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... System Loads § 27.411 Ground clearance: tail rotor guard. (a) It must be impossible for the tail rotor...

  12. 14 CFR 27.411 - Ground clearance: tail rotor guard.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Ground clearance: tail rotor guard. 27.411 Section 27.411 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... System Loads § 27.411 Ground clearance: tail rotor guard. (a) It must be impossible for the tail rotor...

  13. 14 CFR 29.411 - Ground clearance: tail rotor guard.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Ground clearance: tail rotor guard. 29.411 Section 29.411 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... System Loads § 29.411 Ground clearance: tail rotor guard. (a) It must be impossible for the tail rotor...

  14. 14 CFR 27.411 - Ground clearance: tail rotor guard.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Ground clearance: tail rotor guard. 27.411 Section 27.411 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... System Loads § 27.411 Ground clearance: tail rotor guard. (a) It must be impossible for the tail rotor...

  15. 76 FR 17978 - Agency Information Collection Activities: Emergency Clearance Request

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-31

    ... From the Federal Register Online via the Government Publishing Office SOCIAL SECURITY ADMINISTRATION Agency Information Collection Activities: Emergency Clearance Request The Social Security Administration (SSA) publishes a list of information collection packages requiring clearance by the Office of Management and Budget (OMB) in compliance...

  16. 20 CFR 655.150 - Interstate clearance of job order.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 20 Employees' Benefits 3 2013-04-01 2013-04-01 false Interstate clearance of job order. 655.150... job order. (a) SWA posts in interstate clearance system. The SWA must promptly place the job order in... transmit a copy of its active job order to all States listed in the job order as anticipated...

  17. 20 CFR 655.150 - Interstate clearance of job order.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 20 Employees' Benefits 3 2012-04-01 2012-04-01 false Interstate clearance of job order. 655.150... job order. (a) SWA posts in interstate clearance system. The SWA must promptly place the job order in... transmit a copy of its active job order to all States listed in the job order as anticipated...

  18. 20 CFR 655.150 - Interstate clearance of job order.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Interstate clearance of job order. 655.150... job order. (a) SWA posts in interstate clearance system. The SWA must promptly place the job order in... transmit a copy of its active job order to all States listed in the job order as anticipated...

  19. 20 CFR 655.150 - Interstate clearance of job order.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 20 Employees' Benefits 3 2011-04-01 2011-04-01 false Interstate clearance of job order. 655.150... job order. (a) SWA posts in interstate clearance system. The SWA must promptly place the job order in... transmit a copy of its active job order to all States listed in the job order as anticipated...

  20. 20 CFR 655.150 - Interstate clearance of job order.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 20 Employees' Benefits 3 2014-04-01 2014-04-01 false Interstate clearance of job order. 655.150... job order. (a) SWA posts in interstate clearance system. The SWA must promptly place the job order in... transmit a copy of its active job order to all States listed in the job order as anticipated...

  1. Mechanistic evaluation of virus clearance by depth filtration.

    PubMed

    Venkiteshwaran, Adith; Fogle, Jace; Patnaik, Purbasa; Kowle, Ron; Chen, Dayue

    2015-01-01

    Virus clearance by depth filtration has not been well-understood mechanistically due to lack of quantitative data on filter charge characteristics and absence of systematic studies. It is generally believed that both electrostatic interactions and sized based mechanical entrapment contribute to virus clearance by depth filtration. In order to establish whether the effectiveness of virus clearance correlates with the charge characteristics of a given depth filter, a counter-ion displacement technique was employed to determine the ionic capacity for several depth filters. Two depth filters (Millipore B1HC and X0HC) with significant differences in ionic capacities were selected and evaluated for their ability to eliminate viruses. The high ionic capacity X0HC filter showed complete porcine parvovirus (PPV) clearance (eliminating the spiked viruses to below the limit of detection) under low conductivity conditions (≤2.5 mS/cm), achieving a log10 reduction factor (LRF) of > 4.8. On the other hand, the low ionic capacity B1HC filter achieved only ∼2.1-3.0 LRF of PPV clearance under the same conditions. These results indicate that parvovirus clearance by these two depth filters are mainly achieved via electrostatic interactions between the filters and PPV. When much larger xenotropic murine leukemia virus (XMuLV) was used as the model virus, complete retrovirus clearance was obtained under all conditions evaluated for both depth filters, suggesting the involvement of mechanisms other than just electrostatic interactions in XMuLV clearance.

  2. 49 CFR 229.71 - Clearance above top of rail.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Clearance above top of rail. 229.71 Section 229.71....71 Clearance above top of rail. No part or appliance of a locomotive except the wheels, flexible nonmetallic sand pipe extension tips, and trip cock arms may be less than 21/2 inches above the top of rail....

  3. 49 CFR 229.71 - Clearance above top of rail.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Clearance above top of rail. 229.71 Section 229.71....71 Clearance above top of rail. No part or appliance of a locomotive except the wheels, flexible nonmetallic sand pipe extension tips, and trip cock arms may be less than 21/2 inches above the top of rail....

  4. 19 CFR 122.26 - Entry and clearance.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 19 Customs Duties 1 2011-04-01 2011-04-01 false Entry and clearance. 122.26 Section 122.26 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY... information as set forth in § 122.22(c), and grants electronic clearance via electronic mail or telephone....

  5. 14 CFR 29.411 - Ground clearance: tail rotor guard.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Ground clearance: tail rotor guard. 29.411 Section 29.411 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... System Loads § 29.411 Ground clearance: tail rotor guard. (a) It must be impossible for the tail rotor...

  6. 5 CFR 720.307 - Interagency report clearance.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 5 Administrative Personnel 2 2010-01-01 2010-01-01 false Interagency report clearance. 720.307 Section 720.307 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT (CONTINUED) CIVIL SERVICE... Interagency report clearance. The reports contained in this regulation have been cleared in accordance...

  7. 10 CFR 95.53 - Termination of facility clearance.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Termination of facility clearance. 95.53 Section 95.53 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) FACILITY SECURITY CLEARANCE AND SAFEGUARDING OF NATIONAL SECURITY INFORMATION AND RESTRICTED DATA Control of Information § 95.53 Termination of facility...

  8. Benefits of Improved HP Turbine Active Clearance Control

    NASA Technical Reports Server (NTRS)

    Ruiz, Rafael; Albers, Bob; Sak, Wojciech; Seitzer, Ken; Steinetz, Bruce M.

    2007-01-01

    As part of the NASA Propulsion 21 program, GE Aircraft Engines was contracted to develop an improved high pressure turbine(HPT) active clearance control (ACC) system. The system is envisioned to minimize blade tip clearances to improve HPT efficiency throughout the engine operation range simultaneously reducing fuel consumption and emissions.

  9. 48 CFR 245.7310-8 - Antitrust clearance.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Antitrust clearance. 245.7310-8 Section 245.7310-8 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM... Antitrust clearance. When property with an acquisition cost of $3 million or more is to be sold, include...

  10. 30 CFR 77.514 - Switchboards; passageways and clearance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Switchboards; passageways and clearance. 77.514 Section 77.514 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE... COAL MINES Electrical Equipment-General § 77.514 Switchboards; passageways and clearance....

  11. 14 CFR 93.311 - Minimum terrain clearance.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Minimum terrain clearance. 93.311 Section 93.311 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... of Grand Canyon National Park, AZ § 93.311 Minimum terrain clearance. Except in an emergency,...

  12. 33 CFR 160.115 - Withholding of clearance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Withholding of clearance. 160.115... § 160.115 Withholding of clearance. Each District Commander or Captain of the Port may request the Secretary of the Treasury, or the authorized representative thereof, to withhold or revoke the...

  13. 7 CFR 1927.55 - Title clearance services.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 12 2012-01-01 2012-01-01 false Title clearance services. 1927.55 Section 1927.55 Agriculture Regulations of the Department of Agriculture (Continued) RURAL HOUSING SERVICE, RURAL BUSINESS-COOPERATIVE SERVICE, RURAL UTILITIES SERVICE, AND FARM SERVICE AGENCY, DEPARTMENT OF AGRICULTURE PROGRAM REGULATIONS TITLE CLEARANCE AND...

  14. 32 CFR 644.69 - Title Clearance-Easements.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 32 National Defense 4 2014-07-01 2013-07-01 true Title Clearance-Easements. 644.69 Section 644.69 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL PROPERTY REAL ESTATE HANDBOOK Acquisition Procurement of Title Evidence, Title Clearance, and Closings § 644.69 Title Clearance—Easements. (a)...

  15. 32 CFR 644.69 - Title Clearance-Easements.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 32 National Defense 4 2012-07-01 2011-07-01 true Title Clearance-Easements. 644.69 Section 644.69 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL PROPERTY REAL ESTATE HANDBOOK Acquisition Procurement of Title Evidence, Title Clearance, and Closings § 644.69 Title Clearance—Easements. (a)...

  16. 32 CFR 644.69 - Title Clearance-Easements.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 32 National Defense 4 2013-07-01 2013-07-01 false Title Clearance-Easements. 644.69 Section 644.69 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL PROPERTY REAL ESTATE HANDBOOK Acquisition Procurement of Title Evidence, Title Clearance, and Closings § 644.69 Title Clearance—Easements. (a)...

  17. 7 CFR 1927.55 - Title clearance services.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 12 2014-01-01 2013-01-01 true Title clearance services. 1927.55 Section 1927.55 Agriculture Regulations of the Department of Agriculture (Continued) RURAL HOUSING SERVICE, RURAL BUSINESS-COOPERATIVE SERVICE, RURAL UTILITIES SERVICE, AND FARM SERVICE AGENCY, DEPARTMENT OF AGRICULTURE PROGRAM REGULATIONS TITLE CLEARANCE AND...

  18. 32 CFR 644.521 - Limitations on clearance cost.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true Limitations on clearance cost. 644.521 Section 644.521 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL PROPERTY REAL ESTATE HANDBOOK Disposal Clearance of Explosive Hazards and Other Contamination from...

  19. 32 CFR 644.522 - Clearance of military scrap.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true Clearance of military scrap. 644.522 Section 644.522 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL PROPERTY REAL ESTATE HANDBOOK Disposal Clearance of Explosive Hazards and Other Contamination from...

  20. 32 CFR 644.521 - Limitations on clearance cost.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 32 National Defense 4 2011-07-01 2011-07-01 false Limitations on clearance cost. 644.521 Section 644.521 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL PROPERTY REAL ESTATE HANDBOOK Disposal Clearance of Explosive Hazards and Other Contamination from...

  1. 32 CFR 644.522 - Clearance of military scrap.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 32 National Defense 4 2011-07-01 2011-07-01 false Clearance of military scrap. 644.522 Section 644.522 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL PROPERTY REAL ESTATE HANDBOOK Disposal Clearance of Explosive Hazards and Other Contamination from...

  2. 32 CFR 644.527 - Recording Statements of Clearance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true Recording Statements of Clearance. 644.527 Section 644.527 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL PROPERTY REAL ESTATE HANDBOOK Disposal Clearance of Explosive Hazards and Other Contamination from...

  3. 32 CFR 644.527 - Recording Statements of Clearance.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 32 National Defense 4 2011-07-01 2011-07-01 false Recording Statements of Clearance. 644.527 Section 644.527 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) REAL PROPERTY REAL ESTATE HANDBOOK Disposal Clearance of Explosive Hazards and Other Contamination from...

  4. Allometric scaling for predicting human clearance of bisphenol A

    SciTech Connect

    Collet, Séverine H. Picard-Hagen, Nicole Lacroix, Marlène Z. Puel, Sylvie Viguié, Catherine Bousquet-Melou, Alain Toutain, Pierre-Louis Gayrard, Véronique

    2015-05-01

    The investigation of interspecies differences in bisphenol A (BPA) pharmacokinetics (PK) may be useful for translating findings from animal studies to humans, identifying major processes involved in BPA clearance mechanisms, and predicting BPA PK parameters in man. For the first time, a large range of species in terms of body weight, from 0.02 kg (mice) to 495 kg (horses) was used to predict BPA clearance in man by an allometric approach. BPA PK was evaluated after intravenous administration of BPA in horses, sheep, pigs, dogs, rats and mice. A non-compartmental analysis was used to estimate plasma clearance and steady state volume of distribution and predict BPA PK parameters in humans from allometric scaling. In all the species investigated, BPA plasma clearance was high and of the same order of magnitude as their respective hepatic blood flow. By an allometric scaling, the human clearance was estimated to be 1.79 L/min (equivalent to 25.6 mL/kg.min) with a 95% prediction interval of 0.36 to 8.83 L/min. Our results support the hypothesis that there are highly efficient and hepatic mechanisms of BPA clearance in man. - Highlights: • Allometric scaling was used to predict BPA pharmacokinetic parameters in humans. • In all species, BPA plasma clearance approached hepatic blood flow. • Human BPA clearance was estimated to be 1.79 L/min.

  5. 33 CFR 151.1508 - Revocation of clearance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Revocation of clearance. 151.1508 Section 151.1508 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... River § 151.1508 Revocation of clearance. A COTP may request the District Director of Customs...

  6. 32 CFR 644.516 - Clearance of Air Force lands.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 32 National Defense 4 2012-07-01 2011-07-01 true Clearance of Air Force lands. 644.516 Section 644... Excess Land and Improvements § 644.516 Clearance of Air Force lands. The Chief of Engineers has no responsibility for inspecting or clearing excess Air Force land of explosives or chemical/biological...

  7. 32 CFR 644.516 - Clearance of Air Force lands.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 32 National Defense 4 2014-07-01 2013-07-01 true Clearance of Air Force lands. 644.516 Section 644... Excess Land and Improvements § 644.516 Clearance of Air Force lands. The Chief of Engineers has no responsibility for inspecting or clearing excess Air Force land of explosives or chemical/biological...

  8. 32 CFR 644.516 - Clearance of Air Force lands.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 32 National Defense 4 2013-07-01 2013-07-01 false Clearance of Air Force lands. 644.516 Section... Excess Land and Improvements § 644.516 Clearance of Air Force lands. The Chief of Engineers has no responsibility for inspecting or clearing excess Air Force land of explosives or chemical/biological...

  9. 32 CFR 644.516 - Clearance of Air Force lands.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 32 National Defense 4 2011-07-01 2011-07-01 false Clearance of Air Force lands. 644.516 Section... Excess Land and Improvements § 644.516 Clearance of Air Force lands. The Chief of Engineers has no responsibility for inspecting or clearing excess Air Force land of explosives or chemical/biological...

  10. 32 CFR 644.522 - Clearance of military scrap.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 32 National Defense 4 2013-07-01 2013-07-01 false Clearance of military scrap. 644.522 Section 644... Excess Land and Improvements § 644.522 Clearance of military scrap. Military scrap can contain or be... destruction, by using command, of all military scrap and scrap metal from lands suitable for cultivation...

  11. 32 CFR 644.522 - Clearance of military scrap.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 32 National Defense 4 2012-07-01 2011-07-01 true Clearance of military scrap. 644.522 Section 644... Excess Land and Improvements § 644.522 Clearance of military scrap. Military scrap can contain or be... destruction, by using command, of all military scrap and scrap metal from lands suitable for cultivation...

  12. 32 CFR 644.522 - Clearance of military scrap.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 32 National Defense 4 2014-07-01 2013-07-01 true Clearance of military scrap. 644.522 Section 644... Excess Land and Improvements § 644.522 Clearance of military scrap. Military scrap can contain or be... destruction, by using command, of all military scrap and scrap metal from lands suitable for cultivation...

  13. 48 CFR 952.204-73 - Facility clearance.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ....204-73 Section 952.204-73 Federal Acquisition Regulations System DEPARTMENT OF ENERGY CLAUSES AND... granted by the Secretary of Energy. In addition, a Facility Clearance and foreign ownership, control and... Department of Energy Facility Clearance generally need not resubmit the following foreign...

  14. 32 CFR 644.516 - Clearance of Air Force lands.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true Clearance of Air Force lands. 644.516 Section 644... Excess Land and Improvements § 644.516 Clearance of Air Force lands. The Chief of Engineers has no responsibility for inspecting or clearing excess Air Force land of explosives or chemical/biological...

  15. 48 CFR 32.502-2 - Contract finance office clearance.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 1 2014-10-01 2014-10-01 false Contract finance office clearance. 32.502-2 Section 32.502-2 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION... finance office clearance. The contracting officer shall obtain the approval of the contract finance...

  16. 48 CFR 32.502-2 - Contract finance office clearance.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 1 2012-10-01 2012-10-01 false Contract finance office clearance. 32.502-2 Section 32.502-2 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION... finance office clearance. The contracting officer shall obtain the approval of the contract finance...

  17. 48 CFR 1432.502-2 - Contract finance office clearance.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Contract finance office clearance. 1432.502-2 Section 1432.502-2 Federal Acquisition Regulations System DEPARTMENT OF THE INTERIOR... finance office clearance. The CO shall obtain approval of the bureau finance office prior to...

  18. 48 CFR 1432.502-2 - Contract finance office clearance.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 5 2011-10-01 2011-10-01 false Contract finance office clearance. 1432.502-2 Section 1432.502-2 Federal Acquisition Regulations System DEPARTMENT OF THE INTERIOR... finance office clearance. The CO shall obtain approval of the bureau finance office prior to...

  19. 48 CFR 832.502-2 - Contract finance office clearance.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Contract finance office clearance. 832.502-2 Section 832.502-2 Federal Acquisition Regulations System DEPARTMENT OF VETERANS AFFAIRS... finance office clearance. Contracting officers must obtain approval from the DSPE before taking...

  20. 48 CFR 832.502-2 - Contract finance office clearance.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 5 2013-10-01 2013-10-01 false Contract finance office clearance. 832.502-2 Section 832.502-2 Federal Acquisition Regulations System DEPARTMENT OF VETERANS AFFAIRS... finance office clearance. Contracting officers must obtain approval from the DSPE before taking...

  1. 48 CFR 1432.502-2 - Contract finance office clearance.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 5 2014-10-01 2014-10-01 false Contract finance office clearance. 1432.502-2 Section 1432.502-2 Federal Acquisition Regulations System DEPARTMENT OF THE INTERIOR... finance office clearance. The CO shall obtain approval of the bureau finance office prior to...

  2. 48 CFR 832.502-2 - Contract finance office clearance.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 5 2011-10-01 2011-10-01 false Contract finance office clearance. 832.502-2 Section 832.502-2 Federal Acquisition Regulations System DEPARTMENT OF VETERANS AFFAIRS... finance office clearance. Contracting officers must obtain approval from the DSPE before taking...

  3. 48 CFR 32.502-2 - Contract finance office clearance.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 1 2011-10-01 2011-10-01 false Contract finance office clearance. 32.502-2 Section 32.502-2 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION... finance office clearance. The contracting officer shall obtain the approval of the contract finance...

  4. 48 CFR 32.502-2 - Contract finance office clearance.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 1 2013-10-01 2013-10-01 false Contract finance office clearance. 32.502-2 Section 32.502-2 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION... finance office clearance. The contracting officer shall obtain the approval of the contract finance...

  5. 48 CFR 832.502-2 - Contract finance office clearance.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 5 2014-10-01 2014-10-01 false Contract finance office clearance. 832.502-2 Section 832.502-2 Federal Acquisition Regulations System DEPARTMENT OF VETERANS AFFAIRS... finance office clearance. Contracting officers must obtain approval from the DSPE before taking...

  6. 48 CFR 1432.502-2 - Contract finance office clearance.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 5 2013-10-01 2013-10-01 false Contract finance office clearance. 1432.502-2 Section 1432.502-2 Federal Acquisition Regulations System DEPARTMENT OF THE INTERIOR... finance office clearance. The CO shall obtain approval of the bureau finance office prior to...

  7. 48 CFR 32.502-2 - Contract finance office clearance.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Contract finance office clearance. 32.502-2 Section 32.502-2 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION... finance office clearance. The contracting officer shall obtain the approval of the contract finance...

  8. 48 CFR 832.502-2 - Contract finance office clearance.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Contract finance office clearance. 832.502-2 Section 832.502-2 Federal Acquisition Regulations System DEPARTMENT OF VETERANS AFFAIRS... finance office clearance. Contracting officers must obtain approval from the DSPE before taking...

  9. 48 CFR 1432.502-2 - Contract finance office clearance.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Contract finance office clearance. 1432.502-2 Section 1432.502-2 Federal Acquisition Regulations System DEPARTMENT OF THE INTERIOR... finance office clearance. The CO shall obtain approval of the bureau finance office prior to...

  10. The Characteristic Curves of Water

    NASA Astrophysics Data System (ADS)

    Neumaier, Arnold; Deiters, Ulrich K.

    2016-09-01

    In 1960, E. H. Brown defined a set of characteristic curves (also known as ideal curves) of pure fluids, along which some thermodynamic properties match those of an ideal gas. These curves are used for testing the extrapolation behaviour of equations of state. This work is revisited, and an elegant representation of the first-order characteristic curves as level curves of a master function is proposed. It is shown that Brown's postulate—that these curves are unique and dome-shaped in a double-logarithmic p, T representation—may fail for fluids exhibiting a density anomaly. A careful study of the Amagat curve (Joule inversion curve) generated from the IAPWS-95 reference equation of state for water reveals the existence of an additional branch.

  11. Comparison of serum iohexol clearance and plasma creatinine clearance in clinically normal horses.

    PubMed

    Wilson, Katherine E; Wilcke, Jeff R; Crisman, Mark V; Ward, Daniel L; McKenzie, Harold C; Scarratt, W Kent

    2009-12-01

    Objective-To determine whether a limited sampling time method based on serum iohexol clearance (Cl(iohexol)) would yield estimates of glomerular filtration rate (GFR) in clinically normal horses similar to those for plasma creatinine clearance (Cl(creatinine)). Animals-10 clinically normal adult horses. Procedures-A bolus of iohexol (150 mg/kg) was administered IV, and serum samples were obtained 5, 20, 40, 60, 120, 240, and 360 minutes after injection. Urinary clearance of exogenous creatinine was measured during three 20-minute periods. The GFR determined by use of serum Cl(iohexol) and plasma Cl(creatinine) was compared with limits of agreement plots. Results-Values obtained for plasma Cl(creatinine) ranged from 1.68 to 2.69 mL/min/kg (mean, 2.11 mL/min/kg). Mean serum Cl(iohexol) was 2.38 mL/min/kg (range, 1.95 to 3.33 mL/min/kg). Limits of agreement plots indicated good agreement between the methods. Conclusions and Clinical Relevance-Use of serum Cl(iohexol) yielded estimates of GFR in clinically normal adult horses similar to those for plasma Cl(creatinine). This study was the first step in the evaluation of the use of serum Cl(iohexol) for estimating GFR in adult horses.

  12. Multiple CubicBezier Curves.

    ERIC Educational Resources Information Center

    Khonsari, Michael M.; Horn, Douglas

    1990-01-01

    An algorithm is described for generating smooth curves of first-order continuity. The algorithm is composed of several cubic Bezier curves joined together at the user defined control points. Introduced is a tension control parameter which can be set thus providing additional flexibility in the design of free-form curves. (KR)

  13. Titration Curves: Fact and Fiction.

    ERIC Educational Resources Information Center

    Chamberlain, John

    1997-01-01

    Discusses ways in which datalogging equipment can enable titration curves to be measured accurately and how computing power can be used to predict the shape of curves. Highlights include sources of error, use of spreadsheets to generate titration curves, titration of a weak acid with a strong alkali, dibasic acids, weak acid and weak base, and…

  14. A model of clearance rate regulation in mussels

    NASA Astrophysics Data System (ADS)

    Fréchette, Marcel

    2012-10-01

    Clearance rate regulation has been modelled as an instantaneous response to food availability, independent of the internal state of the animals. This view is incompatible with latent effects during ontogeny and phenotypic flexibility in clearance rate. Internal-state regulation of clearance rate is required to account for these patterns. Here I develop a model of internal-state based regulation of clearance rate. External factors such as suspended sediments are included in the model. To assess the relative merits of instantaneous regulation and internal-state regulation, I modelled blue mussel clearance rate and growth using a DEB model. In the usual standard feeding module, feeding is governed by a Holling's Type II response to food concentration. In the internal-state feeding module, gill ciliary activity and thus clearance rate are driven by internal reserve level. Factors such as suspended sediments were not included in the simulations. The two feeding modules were compared on the basis of their ability to capture the impact of latent effects, of environmental heterogeneity in food abundance and of physiological flexibility on clearance rate and individual growth. The Holling feeding module was unable to capture the effect of any of these sources of variability. In contrast, the internal-state feeding module did so without any modification or ad hoc calibration. Latent effects, however, appeared transient. With simple annual variability in temperature and food concentration, the relationship between clearance rate and food availability predicted by the internal-state feeding module was quite similar to that observed in Norwegian fjords. I conclude that in contrast with the usual Holling feeding module, internal-state regulation of clearance rate is consistent with well-documented growth and clearance rate patterns.

  15. Lactate clearance is associated with mortality in septic patients with acute kidney injury requiring continuous renal replacement therapy

    PubMed Central

    Passos, Rogério da Hora; Ramos, Joao Gabriel Rosa; Gobatto, André; Mendonça, Evandro José Bulhões; Miranda, Eva Alves; Dutra, Fábio Ricardo Dantas; Coelho, Maria Fernanda R; Pedroza, Andrea C; Batista, Paulo Benigno Pena; Dutra, Margarida Maria Dantas

    2016-01-01

    Abstract The aim of the study was to assess the clinical utility of lactate measured at different time points to predict mortality at 48 hours and 28 days in septic patients with acute kidney injury (AKI) requiring continuous renal replacement therapy (CRRT). Consecutive critically ill patients with septic AKI requiring CRRT were prospectively studied. Variables were collected at initiation of CRRT and 24 hours later. In total, 186 patients were analyzed. Overall mortality at 48 hours was 28% and at 28 days was 69%. Initial lactate, lactate at 24 hours and the proportion of patients with a lactate clearance superior to 10% were different between survivors at 28 days [2.0 mmol/L, 1.95 mmol/L and 18/45 (40%)] and nonsurvivors [3.46 mmol, 4.66 mmol, and 18/94 (19%)]. Multivariate analysis demonstrated that lactate at 24 hours and lactate clearance, but not initial lactate, were independently associated to mortality. Area under the ROC curves for 28-day mortality was 0.635 for initial lactate; 0.828 for lactate at 24 hours and 0.701 for lactate clearance. Lactate clearance and lactate after 24 hours of CRRT, but not initial lactate, were independently associated with mortality in septic AKI patients undergoing CRRT. Serial lactate measurements may be useful prognostic markers than initial lactate in these patients. PMID:27749594

  16. Quantum relative Lorenz curves

    NASA Astrophysics Data System (ADS)

    Buscemi, Francesco; Gour, Gilad

    2017-01-01

    The theory of majorization and its variants, including thermomajorization, have been found to play a central role in the formulation of many physical resource theories, ranging from entanglement theory to quantum thermodynamics. Here we formulate the framework of quantum relative Lorenz curves, and show how it is able to unify majorization, thermomajorization, and their noncommutative analogs. In doing so, we define the family of Hilbert α divergences and show how it relates with other divergences used in quantum information theory. We then apply these tools to the problem of deciding the existence of a suitable transformation from an initial pair of quantum states to a final one, focusing in particular on applications to the resource theory of athermality, a precursor of quantum thermodynamics.

  17. Multipulse phase resetting curves

    NASA Astrophysics Data System (ADS)

    Krishnan, Giri P.; Bazhenov, Maxim; Pikovsky, Arkady

    2013-10-01

    In this paper, we introduce and study systematically, in terms of phase response curves, the effect of dual-pulse excitation on the dynamics of an autonomous oscillator. Specifically, we test the deviations from linear summation of phase advances resulting from two small perturbations. We analytically derive a correction term, which generally appears for oscillators whose intrinsic dimensionality is >1. The nonlinear correction term is found to be proportional to the square of the perturbation. We demonstrate this effect in the Stuart-Landau model and in various higher dimensional neuronal models. This deviation from the superposition principle needs to be taken into account in studies of networks of pulse-coupled oscillators. Further, this deviation could be used in the verification of oscillator models via a dual-pulse excitation.

  18. 76 FR 36167 - Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-21

    ... Federal Aviation Administration Agency Information Collection Activities: Requests for Comments; Clearance... the request for OMB's clearance of this information collection. Issued in Washington, DC on June 15, 2011. Carla Scott, FAA Information Collection Clearance Officer, IT Enterprises Business...

  19. Automated reasoning about cubic curves.

    SciTech Connect

    Padmanabhan, R.; McCune, W.; Mathematics and Computer Science; Univ. of Manitoba

    1995-01-01

    It is well known that the n-ary morphisms defined on projective algebraic curves satisfy some strong local-to-global equational rules of derivation not satisfied in general by universal algebras. For example, every rationally defined group law on a cubic curve must be commutative. Here we extract from the geometry of curves a first order property (gL) satisfied by all morphisms defined on these curves such that the equational consequences known for projective curves can be derived automatically from a set of six rules (stated within the first-order logic with equality). First, the rule (gL) is implemented in the theorem-proving program Otter. Then we use Otter to automatically prove some incidence theorems on projective curves without any further reference to the underlying geometry or topology of the curves.

  20. Effects of drugs on mucus clearance.

    PubMed

    Houtmeyers, E; Gosselink, R; Gayan-Ramirez, G; Decramer, M

    1999-08-01

    Mucociliary clearance (MCC), the process in which airway mucus together with substances trapped within are moved out of the lungs, is an important defence mechanism of the human body. Drugs may alter this process, such that it is necessary to know the effect of the drugs on MCC. Indeed, agents stimulating MCC may be used therapeutically in respiratory medicine, especially in patients suspected of having an impairment of their mucociliary transport system. In contrast, caution should be taken with drugs depressing MCC as an undesired side-effect, independently of their therapeutic indication. Since cough clearance (CC) serves as a back-up system when MCC fails, the influence of drugs must be examined not only on MCC but also on CC. Ultimately, the clinical repercussions of alterations in mucus transport induced by drug administration must be studied. Tertiary ammonium compounds (anticholinergics), aspirin, anaesthetic agents and benzodiazepines have been shown to be capable of depressing the mucociliary transport system. Cholinergics, methylxanthines, sodium cromoglycate, hypertonic saline, saline as well as water aerosol have been shown to increase MCC. Adrenergic antagonists, guaifenesin, S-carboxymethylcysteine, sodium 2-mercapto-ethane sulphonate and frusemide have been reported not to alter the mucociliary transport significantly. Amiloride, uridine 5'-triphosphate (UTP), quaternary ammonium compounds (anticholinergics), adrenergic agonists, corticosteroids, recombinant human deoxyribonuclease (rhDNase), N-acetylcysteine, bromhexine and ambroxol have been reported either not to change or to augment MCC. Indirect data suggest that surfactant as well as antibiotics may improve the mucociliary transport system. As for the influence of drugs on CC, amiloride and rhDNase have been demonstrated to increase the effectiveness of cough. A trend towards an improved CC was noted after treatment with adrenergic agonists. The anticholinergic agent ipratropium bromide, which

  1. Foot clearance during stair descent: effects of age and illumination.

    PubMed

    Hamel, Kathryn A; Okita, Noriaki; Higginson, Jill S; Cavanagh, Peter R

    2005-02-01

    It is likely that many stair accidents result from a trip during stair negotiation, yet few studies have examined the exact nature of balance loss during falls on stairs. The purpose of this study was to investigate potential age-related differences in the minimum clearance of the foot during stair descent, and to explore whether the minimum foot clearance was affected by the available ambient lighting. Twelve young adults (24+/-3.3 years) and 10 older adults (73.7+/-1.9 years) participated in the study. The older adults had significantly greater within subject coefficients of variation compared to the young adults, and had a significantly larger number of minimum foot clearances which fell below 5 mm. While the young subjects increased their minimum clearance by 3.6 mm on average in response to a decrease in ambient lighting, the older adults maintained the same clearance over all stairs except one. These results suggest that the variability of minimum foot clearance, and lack of precautionary increases in foot clearance under reduced lighting may contribute to falls on stairs by the elderly.

  2. Integrated Turbine Tip Clearance and Gas Turbine Engine Simulation

    NASA Technical Reports Server (NTRS)

    Chapman, Jeffryes W.; Kratz, Jonathan; Guo, Ten-Huei; Litt, Jonathan

    2016-01-01

    Gas turbine compressor and turbine blade tip clearance (i.e., the radial distance between the blade tip of an axial compressor or turbine and the containment structure) is a major contributing factor to gas path sealing, and can significantly affect engine efficiency and operational temperature. This paper details the creation of a generic but realistic high pressure turbine tip clearance model that may be used to facilitate active tip clearance control system research. This model uses a first principles approach to approximate thermal and mechanical deformations of the turbine system, taking into account the rotor, shroud, and blade tip components. Validation of the tip clearance model shows that the results are realistic and reflect values found in literature. In addition, this model has been integrated with a gas turbine engine simulation, creating a platform to explore engine performance as tip clearance is adjusted. Results from the integrated model explore the effects of tip clearance on engine operation and highlight advantages of tip clearance management.

  3. A novel relay method for determining low-clearance values.

    PubMed

    Di, Li; Trapa, Patrick; Obach, R Scott; Atkinson, Karen; Bi, Yi-An; Wolford, Angela C; Tan, Beijing; McDonald, Thomas S; Lai, Yurong; Tremaine, Larry M

    2012-09-01

    A novel relay method has been developed using cryopreserved human hepatocytes to measure intrinsic clearance of low-clearance compounds. The relay method involved transferring the supernatant from hepatocyte incubations to freshly thawed hepatocytes at the end of the 4-h incubation to prolong the exposure time to active enzymes in hepatocytes. An accumulative incubation time of 20 h or longer in hepatoctyes can be achieved using the method. The relay method was validated using seven commercial drugs (diazepam, disopyramide, theophylline, timolol, tolbutamide, S-warfarin, and zolmitriptan) that were metabolized by various cytochrome P450s with low human in vivo intrinsic clearance at approximately 2 to 15 ml · min⁻¹ · kg⁻¹. The results showed that the relay method produced excellent predictions of human in vivo clearance. The difference between in vitro and in vivo intrinsic clearance was within 2-fold for most compounds, which is similar to the standard prediction accuracy for moderate to high clearance compounds using hepatocytes. The relay method is a straightforward, relatively low cost, and easy-to-use new tool to address the challenges of low clearance in drug discovery and development.

  4. Birational maps that send biquadratic curves to biquadratic curves

    NASA Astrophysics Data System (ADS)

    Roberts, John A. G.; Jogia, Danesh

    2015-02-01

    Recently, many papers have begun to consider so-called non-Quispel-Roberts-Thompson (QRT) birational maps of the plane. Compared to the QRT family of maps which preserve each biquadratic curve in a fibration of the plane, non-QRT maps send a biquadratic curve to another biquadratic curve belonging to the same fibration or to a biquadratic curve from a different fibration of the plane. In this communication, we give the general form of a birational map derived from a difference equation that sends a biquadratic curve to another. The necessary and sufficient condition for such a map to exist is that the discriminants of the two biquadratic curves are the same (and hence so are the j-invariants). The result allows existing examples in the literature to be better understood and allows some statements to be made concerning their generality.

  5. Pulmonary 99mTc-DTPA aerosol clearance and survival in usual interstitial pneumonia (UIP)

    PubMed Central

    Mogulkoc, N; Brutsche, M; Bishop, P; Murby, B; Greaves, M; Horrocks, A; Wilson, M; McCullough, C; Prescott, M; Egan, J

    2001-01-01

    BACKGROUND—Clearance of inhaled technetium 99m-labelled diethylenetriamine penta-acetic acid (99mTc-DTPA) from the lungs is a potential indicator of disease progression in patients with idiopathic pulmonary fibrosis (IPF).
METHODS—We prospectively analysed the usefulness of this technique for predicting survival in 106 non-smoking patients with usual interstitial pneumonia (UIP) pattern IPF diagnosed by high resolution CT (HRCT) scanning or histological examination (M/F 65/41, mean (SD) age 61 (11) years). DTPA clearance was analysed according to both mono-exponential and bi-exponential models. Half times for the fast (t0.5F) and slow (t0.5S) components of clearance, the percentage contribution of the fast component (fF), and half time for mono-exponential approximation to the early part of the clearance curve (t0.5) were calculated.
RESULTS—The patients had substantially faster t0.5 (mean 23.9 (9.6) minutes) than normal values (>45 minutes). Thirty seven patients (35%) died during follow up (median 15 months). Univariate Cox regression analysis identified significant predictors of survival as age, forced expiratory volume in 1 second (FEV1), forced vital capacity (FVC), total lung capacity (TLC), % predicted TLC, carbon monoxide transfer factor (TLCO), % predicted TLCO, arterial oxygen tension (PaO2), oxygen saturation, t0.5F, and HRCT fibrosis score. Multiple stepwise Cox regression analysis identified t0.5F (p=0.03, hazard ratio 0.747, 95% CI 0.578 to 0.964), % predicted TLC (p=0.02, hazard ratio 0.976, 95% CI 0.956 to 0.995), % predicted TLCO (p=0.003, hazard ratio 0.960, 95% CI 0.935 to 0.986), and age (p=0.003, hazard ratio 1.062, 95% CI 1.021 to 1.104) as independent predictors of survival.
CONCLUSION—These data suggest that 99mTc-DTPA clearance t0.5F measurement may predict survival in patients with UIP pattern IPF.

 PMID:11713353

  6. Toward a Fast-Response Active Turbine Tip Clearance Control

    NASA Technical Reports Server (NTRS)

    Melcher, Kevin J.; Kypuros, Javier A.

    2003-01-01

    This paper describes active tip clearance control research being conducted by NASA to improve turbine engine systems. The target application for this effort is commercial aircraft engines. However, technologies developed for clearance control can benefit a broad spectrum of current and future turbomachinery. The first portion of the paper addresses the research from a programmatic viewpoint. Recent studies that provide motivation for the work, identification of key technologies, and NASA's plan for addressing deficiencies in the technologies are discussed. The later portion of the paper drills down into one of the key technologies by presenting equations and results for a preliminary dynamic model of the tip clearance phenomena.

  7. Ion exchange chromatography of proteins and clearance of aggregates.

    PubMed

    Yigzaw, Y; Hinckley, P; Hewig, A; Vedantham, G

    2009-06-01

    Clearance of product related aggregates in therapeutic proteins is a major focus of purification process development. A typical purification process will have one or two chromatographic steps that remove these product related aggregates to an acceptable level. Both cation exchange and anion exchange chromatography can provide robust clearance of aggregates. The primary factors that are critical for aggregate clearance are: resin chemistry, binding and elution condition, peak collection and column load factor. This review covers how these factors can be optimized to increase the effectiveness of ion exchange chromatography in removing aggregates.

  8. Time-of-Flight Tip-Clearance Measurements

    NASA Technical Reports Server (NTRS)

    Dhadwal, H. S.; Kurkov, A. P.; Janetzke, D. C.

    1999-01-01

    In this paper a time-of-flight probe system incorporating the two integrated fiber optic probes which are tilted equally relative to the probe holder centerline, is applied for the first time to measure the tip clearance of an advanced fan prototype. Tip clearance is largely independent of the signal amplitude and it relies on timing measurement. This work exposes optical effects associated with the fan blade stagger angle that were absent during the original spin-rig experiment on the zero stagger rotor. Individual blade tip clearances were measured with accuracy of +/- 127-mm (+/- 0.005-in). Probe features are discussed and improvements to the design are suggested.

  9. Laser-optical blade tip clearance measurement system

    NASA Technical Reports Server (NTRS)

    Barranger, J. P.; Ford, M. J.

    1979-01-01

    A laser-optical measurement system was developed to measure single blade tip clearances and average blade tip clearances between a rotor and its gas path seal in rotating component rigs and complete engines. The system is applicable to fan, compressor and turbine blade tip clearance measurements. The engine mounted probe is particularly suitable for operation in the extreme turbine environment. The measurement system consists of an optical subsystem, an electronic subsystem and a computing and graphic terminal. Bench tests and environmental tests were conducted to confirm operation at temperatures, pressures, and vibration levels typically encountered in an operating gas turbine engine.

  10. Aerosol Medications for Treatment of Mucus Clearance Disorders.

    PubMed

    Rubin, Bruce K

    2015-06-01

    Airway mucus hypersecretion and secretion retention can result from inflammation, irritation, stimulation, or mucus-producing tumors. Secretion clearance can be furthered hampered by ciliary dysfunction and by weakness or restrictive lung disease, leading to an ineffective cough. There are a number of different mucoactive medications that have been used to reduce hypersecretion, make secretions easier to transport, or increase the efficiency of cough or mucus clearance. In this paper, I review the pathophysiology of secretory hyper-responsiveness and mucus hypersecretion and discuss the different aerosol medications that can be used to augment secretion clearance.

  11. Metabolic clearance rate and urinary clearance of purified beta-core

    SciTech Connect

    Wehmann, R.E.; Blithe, D.L.; Flack, M.R.; Nisula, B.C. )

    1989-09-01

    We injected a highly purified preparation of the beta-core molecule, a fragment of hCG beta excreted in pregnancy urine, into five men and three women to determine its kinetic parameters, MCR, and urinary clearance. The beta-core molecule was distributed in an initial volume (1950 +/- 156 (mean +/- SEM) mL/m2 body surface area) approximately equal to the estimated plasma volume. Its disappearance was multiexponential on a semilogarithmic plot, with a rapid phase t1/2 of 3.5 +/- 0.7 min and a slow phase t1/2 of 22.4 +/- 4.2 min. The transit time (the mean time spent by a molecule of beta-core in transit) was 20.6 +/- 2.1 min. The MCR was 192.0 +/- 8.0 mL/min.m2 body surface area. About 5% of the injected dose of beta-core was excreted into the urine in the first 30 min after injection, and low levels of excretion persisted for up to 7 days. The urinary clearance rate of beta-core was 13.7 +/- 1.4 mL/min.m2, accounting for about 8% of the elimination of beta-core from the plasma. The beta-core immunoreactivity in serum and urine was characterized by gel filtration and three independent RIA systems to show that its properties were indistinguishable from those of the injected beta-core. Serum levels of beta-core in pregnant women were less than 0.2 ng/mL, while the amounts excreted in their urine were as much as 5 mg/day. Based on these clearance parameters of beta-core in normal subjects, less than 0.2% of the beta-core excreted in pregnancy urine is derived by urinary clearance of plasma beta-core. Therefore, more than 99% of the beta-core excreted in pregnancy urine is derived from beta-core in a compartment separate from plasma. In particular, these data indicate that there is relatively little placental secretion of beta-core into plasma and that placental secretion does not account for the vast majority of beta-core in pregnancy urine.

  12. A numerical method for biphasic curve fitting with a programmable calculator.

    PubMed

    Ristanović, D; Ristanović, D; Malesević, J; Milutinović, B

    1982-01-01

    Elimination kinetics of bromsulphalein (BSP) after a single injection into the circulation of rats were examined by means of a four-compartment model. BSP plasma concentrations were measured colorimetrically. A program written for the Texas Instruments TI-59 programmable calculator is presented, which will calculate the fractional blood clearance of BSP using an iteration procedure. A simple method of fitting biphasic decay curves to experimental data is also proposed.

  13. Langevin Equation on Fractal Curves

    NASA Astrophysics Data System (ADS)

    Satin, Seema; Gangal, A. D.

    2016-07-01

    We analyze random motion of a particle on a fractal curve, using Langevin approach. This involves defining a new velocity in terms of mass of the fractal curve, as defined in recent work. The geometry of the fractal curve, plays an important role in this analysis. A Langevin equation with a particular model of noise is proposed and solved using techniques of the Fα-Calculus.

  14. Reflection of curved shock waves

    NASA Astrophysics Data System (ADS)

    Mölder, S.

    2017-03-01

    Shock curvatures are related to pressure gradients, streamline curvatures and vorticity in flows with planar and axial symmetry. Explicit expressions, in an influence coefficient format, are used to relate post-shock pressure gradient, streamline curvature and vorticity to pre-shock gradients and shock curvature in steady flow. Using higher order, von Neumann-type, compatibility conditions, curved shock theory is applied to calculate the flow near singly and doubly curved shocks on curved surfaces, in regular shock reflection and in Mach reflection. Theoretical curved shock shapes are in good agreement with computational fluid dynamics calculations and experiment.

  15. Shape Preserving Interpolation by Curves

    DTIC Science & Technology

    2001-07-01

    curves Given data 1i E R2 , i = 0,..., N, we consider a curve r : [a, b] -- R2 satisfying r(ti) = Ii , i = 0,..., N, (3.1) for values a = to < tj...tN = b. For a closed curve the situation is extended periodically so that Ii +N =10, ti+N =ti, i E Z, r(t+b-a) =r(t), tc R. 3.1 Desirable properties...para- meterisation). When all vi = 0, r will reduce to the usual C2 cubic spline interpolant. As vi --+ oc, the curve is ’pulled tight’ at Ii and as

  16. Intraarticular volume and clearance in human synovial effusions

    SciTech Connect

    Wallis, W.J.; Simkin, P.A.; Nelp, W.B.; Foster, D.M.

    1985-04-01

    Intraarticular volumes were measured by radiolabeled albumin (RISA) distribution in chronic knee effusions from 11 rheumatoid arthritis patients and 9 osteoarthritis patients. Volumes of synovial fluid obtained at joint aspiration were substantially less than those found by RISA dilution. Up to 24 hours was needed for full distribution of RISA throughout the intraarticular compartment. Measured 123I and RISA radioactivity over the knee described monoexponential rate constants, lambda (minute-1). The clearance of 123I and RISA from synovial effusions was derived by the formulation volume (ml) X lambda (minute-1) = clearance (ml/minute). RISA clearance in rheumatoid effusions was significantly greater than that found in osteoarthritis effusions. Intraarticular volume and isotope clearance were easily quantified and provide measures for further evaluating the microvascular physiology of synovial effusions.

  17. High Temperature Evaluation of an Active Clearance Control System Concept

    NASA Technical Reports Server (NTRS)

    Taylor, Shawn C.; Steinetz, Bruce M.; Oswald, Jay J.

    2006-01-01

    A mechanically actuated blade tip clearance control concept was evaluated in a nonrotating test rig to quantify secondary seal leakage at elevated temperatures. These tests were conducted to further investigate the feasibility of actively controlling the clearance between the rotor blade tips and the surrounding shroud seal in the high pressure turbine (HPT) section of a turbine engine. The test environment simulates the state of the back side of the HPT shroud seal with pressure differentials as high as 120 psig and temperatures up to 1000 F. As expected, static secondary seal leakage decreased with increasing temperature. At 1000 F, the test rig's calculated effective clearance (at 120 psig test pressure) was 0.0003 in., well within the industry specified effective clearance goal.

  18. 32 CFR 644.517 - Clearance of Army lands.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Clearance, the following information will be furnished to the DE upon completion of the neutralization: (a) Records of the neutralization work performed, including statement of methods employed. (b) List...

  19. 77 FR 44641 - Critical Infrastructure Private Sector Clearance Program Request

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-07-30

    ... SECURITY Critical Infrastructure Private Sector Clearance Program Request AGENCY: National Protection and... comments concerning Reinstatement, with change, of a previously approved ICR for the Critical... sector partners who are responsible for critical infrastructure protection but would not otherwise...

  20. Laser-optical blade tip clearance measurement system

    NASA Technical Reports Server (NTRS)

    Barranger, J. P.; Ford, M. J.

    1980-01-01

    The need for blade tip clearance instrumentation has been intensified recently by advances in technology of gas turbine engines. A new laser-optical measurement system has been developed to measure single blade tip clearances and average blade tip clearances between a rotor and its gas path seal in rotating component rigs and complete engines. The system is applicable to fan, compressor and turbine blade tip clearance measurements. The engine mounted probe is particularly suitable for operation in the extreme turbine environment. The measurement system consists of an optical subsystem, an electronic subsystem and a computing and graphic terminal. Bench tests and environmental tests were conducted to confirm operation at temperatures, pressures, and vibration levels typically encountered in an operating gas turbine engine.

  1. Clearance detector and method for motion and distance

    DOEpatents

    Xavier, Patrick G.

    2011-08-09

    A method for correct and efficient detection of clearances between three-dimensional bodies in computer-based simulations, where one or both of the volumes is subject to translation and/or rotations. The method conservatively determines of the size of such clearances and whether there is a collision between the bodies. Given two bodies, each of which is undergoing separate motions, the method utilizes bounding-volume hierarchy representations for the two bodies and, mappings and inverse mappings for the motions of the two bodies. The method uses the representations, mappings and direction vectors to determine the directionally furthest locations of points on the convex hulls of the volumes virtually swept by the bodies and hence the clearance between the bodies, without having to calculate the convex hulls of the bodies. The method includes clearance detection for bodies comprising convex geometrical primitives and more specific techniques for bodies comprising convex polyhedra.

  2. IFNL4 affects clearance of hepatitis C virus

    Cancer.gov

    Scientists have discovered a new human interferon gene, Interferon Lambda 4 (IFNL4), that affects clearance of the hepatitis C virus. They also identified an inherited genetic variant within IFNL4 that predicts how people respond to treatment for hepatit

  3. Antibody-Mediated Clearance of Alphavirus Infection from Neurons

    NASA Astrophysics Data System (ADS)

    Levine, Beth; Hardwick, J. Marie; Trapp, Bruce D.; Crawford, Thomas O.; Bollinger, Robert C.; Griffin, Diane E.

    1991-11-01

    Humoral immunity is important for protection against viral infection and neutralization of extracellular virus, but clearance of virus from infected tissues is thought to be mediated solely by cellular immunity. However, in a SCID mouse model of persistent alphavirus encephalomyelitis, adoptive transfer of hyperimmune serum resulted in clearance of infectious virus and viral RNA from the nervous system, whereas adoptive transfer of sensitized T lymphocytes had no effect on viral replication. Three monoclonal antibodies to two different epitopes on the E2 envelope glycoprotein mediated viral clearance. Treatment of alphavirus-infected primary cultured rat neurons with these monoclonal antibodies to E2 resulted in decreased viral protein synthesis, followed by gradual termination of mature infectious virion production. Thus, antibody can mediate clearance of alphavirus infection from neurons by restricting viral gene expression.

  4. Further Characterization of an Active Clearance Control Concept

    NASA Technical Reports Server (NTRS)

    Taylor, Shawn C.; Steinetz, Bruce M.; Oswald, Jay J.

    2007-01-01

    A new test chamber and precision hydraulic actuation system were incorporated into an active clearance control (ACC) test rig at NASA Glenn Research Center. Using the improved system, a fast-acting, mechanically-actuated, ACC concept was evaluated at engine simulated temperatures and pressure differentials up to 1140 F and 120 psig, on the basis of secondary seal leakage and kinematic controllability. During testing, the ACC concept tracked a simulated flight clearance transient profile at 1140 F, 120 psig, with a maximum error of only 0.0012 in. Comparison of average dynamic leakage of the system with average static leakage did not show significant differences between the two operating conditions. Calculated effective clearance values for the rig were approximately 0.0002 in. at 120 psig, well below the industry specified effective clearance threshold of 0.001 in.

  5. Early Agriculture: Land Clearance and Climate Effects

    NASA Astrophysics Data System (ADS)

    Ruddiman, W. F.

    2013-12-01

    inception. Well-dated high-resolution CO2 (and CH4) records from ice cores show gas decreases that correlate closely with major pandemics and civil strife, but show little if any link to temperature or precipitation trends. One significant (and intriguing) discrepancy with the original hypothesis remains. Most of the CO2 rise occurred between 6000 and 2500 years ago, well before the major increase in global population that has been hindcast from geometric models that assume a constant fractional rate of population increase. Some of this discrepancy has been reconciled by historical evidence showing much higher per-capita clearance millennia ago than later in pre-industrial time, resulting in disproportionately large early clearance and CO2 emissions. In addition, DNA studies and archeological syntheses now indicate that early farming populations initially grew at very fast rates favored by environments rich in basic resources (especially fertile soils), but then slowed in later millennia because of growing resource limitations and the effects of pandemics and civil strife in checking population growth. This emerging view of fast-rising early population trends has the potential to account for the early timing of the CO2 increase.

  6. Enhanced Bomb Effects for Obstacle Clearance (Analysis Task)

    DTIC Science & Technology

    1998-01-01

    Enhanced Bomb Effects for Obstacle Clearance (Analysis Task) Tim Hennessey Diane Nell Naval Surface Warfare Center, Indian Head Division 101 Strauss...need for a system capable of simultaneously breaching obstacles and clearing mines, in-stride, from over the horizon, during an amphibious assault...In response to the obstacle -breaching concern, the Enhanced Bomb Effects for Obstacle Clearance program was started. The purpose of the NSWCDD/CSS

  7. Measuring Motor-Shaft Clearance And Wobble During Operation

    NASA Technical Reports Server (NTRS)

    Chern, Engmin James

    1996-01-01

    Noncontact proximity sensor, preferably eddy-current liftoff probe, provides realtime measurement of distance and small variations of distance between two mechanical components designed to be maintained at precise, fixed distance. In particular, system intended for use in measuring lateral clearance and variations in lateral clearance (wobble) of motor shaft relative to motor housing while shaft turning. Provides early indication of wear in motor bearings. Rate of rotation also measured.

  8. [Methohexital clearance in patients with acute hepatitis (author's transl)].

    PubMed

    Richter, E; Gallenkamp, H; Heusler, H; Zilly, W; Breimer, D D

    1979-10-26

    Pharmacokinetics of methohexital were studied in patients with acute hepatitis and after a treatment period either with "essential phospholipids" or phenobarbital. During the acute phase the distribution of methohexital was significantly altered. No change had been observed in the methohexital clearance. During remission the distribution of methohexital was in a normal range. After treatment with phenobarbital the methohexital clearance increased significantly whereas no change was observed after treatment with "essential phospholipids".

  9. Control of Small Robotic Vehicles In Unexploded Ordnance Clearance

    DTIC Science & Technology

    1997-04-01

    Proceedings of the IEEE ICRA97, Albuquerque, New Mexico, April 20-25, 1997 ISBN 0-7803-3904-5 Control of Small Robotic Vehicles In Unexploded...multiple small robotic vehicles for performing mine field clearance, and the related problem of clearing unexploded ordnance from areas of interest...charge that could be detonated upon command. Results given in this paper includes the performance of clearance operations with behavior based robots

  10. Intradialytic clearance of opioids: methadone versus hydromorphone.

    PubMed

    Perlman, Ryan; Giladi, Hili; Brecht, Krista; Ware, Mark A; Hebert, Terence E; Joseph, Lawrence; Shir, Yoram

    2013-12-01

    Opioids are commonly prescribed to patients with chronic pain associated with end-stage renal disease requiring hemodialysis. The stability of opioid analgesia during dialysis may vary among different opioids. No studies to date have corroborated this clinical observation by directly comparing plasma concentrations of different opioids during dialysis. We compared changes in peridialysis plasma concentrations of 2 pharmacokinetically distinct opioids, methadone and hydromorphone (HM). Fourteen dialysis patients with chronic pain received either methadone or HM for at least 2 weeks before beginning the study. Blood samples were obtained immediately before, during, and after hemodialysis in 2 separate dialysis sessions, 1 week apart, and were analyzed for opioid concentrations. Methadone plasma concentrations were more stable during hemodialysis compared to HM: the mean percent change of methadone plasma levels was 14.9% ± 8.2% (± SD) compared with 55.1% ± 8.1% in the HM treatment group, a difference of 40.2% (95% confidence interval 17.14 to 63.14). The mean plasma clearance of methadone was 19.9 ± 8.5 mL/min (± SD) compared with 105.7 ± 8.3 mL/min for HM, a difference of 85.7 mL/min (95% confidence interval 61.9 to 109.1). There were no differences between the 2 opioid groups in pain scores, side effect profile, and quality of life. Methadone therapy was not associated with an increased rate of adverse events. If confirmed by larger clinical studies, methadone could be considered as one of the opioids of choice in dialysis patients.

  11. Calculation of Tip Clearance Effects in a Transonic Compressor Rotor

    NASA Technical Reports Server (NTRS)

    Chima, R. V.

    1998-01-01

    The flow through the tip clearance region of a transonic compressor rotor (NASA rotor 37) was computed and compared to aerodynamic probe and laser anemometer data. Tip clearance effects were modeled both by gridding the clearance gap and by using a simple periodicity model across the ungridded gap. The simple model was run with both the full gap height, and with half the gap height to simulate a vena-contracta effect. Comparisons between computed and measured performance maps and downstream profiles were used to validate the models and to assess the effects of gap height on the simple clearance model. Recommendations were made concern- ing the use of the simple clearance model Detailed comparisons were made between the gridded clearance gap solution and the laser anemometer data near the tip at two operating points. The computed results agreed fairly well with the data but overpredicted the extent of the casing separation and underpredicted the wake decay rate. The computations were then used to describe the interaction of the tip vortex, the passage shock, and the casing boundary layer.

  12. Calculation of tip clearance effects in a transonic compressor rotor

    NASA Technical Reports Server (NTRS)

    Chima, R. V.

    1996-01-01

    The flow through the tip clearance region of a transonic compressor rotor (NASA rotor 37) was computed and compared to aerodynamic probe and laser anemometer data. Tip clearance effects were modeled both by gridding the clearance gap and by using a simple periodicity model across the ungridded gap. The simple model was run with both the full gap height, and with half the gap height to simulate a vena-contracta effect. Comparisons between computed and measured performance maps and downstream profiles were used to validate the models and to assess the effects of gap height on the simple clearance model. Recommendations were made concerning the use of the simple clearance model. Detailed comparisons were made between the gridded clearance gap solution and the laser anemometer data near the tip at two operating points. The computer results agreed fairly well with the data but overpredicted the extent of the casing separation and underpredicted the wake decay rate. The computations were then used to describe the interaction of the tip vortex, the passage shock, and the casing boundary layer.

  13. Model of mucociliary clearance in cystic fibrosis lungs.

    PubMed

    Kurbatova, P; Bessonov, N; Volpert, V; Tiddens, H A W M; Cornu, C; Nony, P; Caudri, D

    2015-05-07

    Mucus clearance is a primary innate defense mechanism in the human airways. Cystic fibrosis (CF) is a genetic disease caused by mutations in the gene encoding the cystic fibrosis transmembrane conductance regulator (CFTR) protein. CF is characterized by dehydration of airway surface liquid and impaired mucociliary clearance. As a result, microorganisms are not efficiently removed from the airways, and patients experience chronic pulmonary infections and inflammation. We propose a new physiologically based mathematical model of muco-ciliary transport consisting of the two major components of the mucociliary clearance system: (i) periciliary liquid layer (PCL) and (ii) mucus layer. We study mucus clearance under normal conditions and in CF patients. Restoring impaired clearance of airway secretions in one of the major goals of therapy in patients with CF. We consider the action of the aerosolized and inhaled medication dornase alfa, which reduces the viscosity of cystic fibrosis mucus, by selectively cleaving the long DNA strands it contains. The results of the model simulations stress the potential relevance of the location of the drug deposition in the central or peripheral airways. Mucus clearance was increased in case the drug was primarily deposited peripherally, i.e. in the small airways.

  14. A high sensitivity inductive sensor for blade tip clearance measurement

    NASA Astrophysics Data System (ADS)

    Du, Li; Zhu, Xiaoliang; Zhe, Jiang

    2014-06-01

    A multiplexed inductive sensor consisting of multiple mini-sized planar spiral coils for detecting multiple tip clearances of rotor blades is presented. The sensor measures the tip clearances by monitoring the inductance changes of planar spiral coils caused by the passage of the rotor blades. A resonance frequency division multiplexing technique and parallel LC resonance measurement were applied to the multiple sensor coils, making it feasible to measure multiple tip clearances using only one set of measurement electronics with high sensitivity and resolution. The results from tests conducted on a bench-top test rig have demonstrated that the sensor is capable of simultaneously measuring multiple tip clearances from 0 to 5 mm with a 10 μm resolution at a high rotary speed up to 80 000 RPM. With its high resolution, high sensitivity and capability of monitoring a large number of tip clearances simultaneously, this sensor can potentially be used for advanced active tip clearance control in turbine machinery.

  15. Learning curves in health care.

    PubMed

    Waldman, J Deane; Yourstone, Steven A; Smith, Howard L

    2003-01-01

    This article explores the uses of learning curve theory in medicine. Though effective application of learning curve theory in health care can result in higher quality and lower cost, it is seldom methodically applied in clinical practice. Fundamental changes are necessary in the corporate culture of medicine in order to capitalize maximally on the benefits of learning.

  16. 48 CFR 245.603-70 - Contractor performance of plant clearance duties.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... plant clearance duties. 245.603-70 Section 245.603-70 Federal Acquisition Regulations System DEFENSE..., Redistribution, and Disposal of Contractor Inventory 245.603-70 Contractor performance of plant clearance duties... clearance functions if the volume of plant clearance warrants performance by the contractor. (2) The...

  17. 48 CFR 245.7101-4 - DD Form 1640, Request for Plant Clearance.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Plant Clearance. 245.7101-4 Section 245.7101-4 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT OF DEFENSE CONTRACT MANAGEMENT GOVERNMENT PROPERTY Plant Clearance Forms 245.7101-4 DD Form 1640, Request for Plant Clearance. Use to request plant clearance assistance...

  18. 48 CFR 245.7002 - Duties and responsibilities of plant clearance officers.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... responsibilities of plant clearance officers. 245.7002 Section 245.7002 Federal Acquisition Regulations System... Appointment of Property Administrators and Plant Clearance Officers 245.7002 Duties and responsibilities of plant clearance officers. The plant clearance officer shall— (a) Instruct the contractor on...

  19. The plasma clearance of the Fusarium toxin deoxynivalenol (DON) is decreased in endotoxemic pigs.

    PubMed

    Dänicke, Sven; Brosig, Bianca; Kahlert, Stefan; Panther, Patricia; Reinhardt, Nicole; Diesing, Anne-Kathrin; Kluess, Jeannette; Kersten, Susanne; Valenta, Hana; Rothkötter, Hermann-Josef

    2012-12-01

    The plasma elimination kinetics of the Fusarium toxin deoxynivalenol (DON) was investigated in male castrated pigs (40.4±3.7 kg) when infused intravenously either alone (100 μg/kg/h, n=6) or together with lipopolysaccharides (LPS, 7.5 μg/kg/h, n=6). The maximum DON concentration after one hour of infusion was significantly higher by 61% in the DON+LPS Group compared to pigs infused with DON alone. The area under the plasma DON concentration vs. time curve of the DON+LPS Group was approximately twice as high as that of the DON Group after 24h while the initial (0.63 vs. 0.6 h) and terminal half-lifes (2.97 vs. 2.30 h) remained uninfluenced. The apparent volume of distribution and the plasma clearance were significantly lower for the DON+LPS Group compared to the DON Group (2.14 vs. 1.45 L/kg and 11.9 vs. 5.87 mL/kg/min). Glucuronidated DON seemed to persist longer in the DON+LPS Group. In conclusion, clearance of DON was decreased during an LPS induced acute phase reaction in pigs. Whether the higher plasma DON concentrations in endotoxemic pigs are due to a hemodynamically associated longer persistence of the DON glucuronide or because of an altered glucuronidation activity needs to be examined further.

  20. Modulation of antipyrine clearance by polysaccharide peptide (PSP) isolated from Coriolus versicolor in the rat.

    PubMed

    Chan, Siu-Lung; Yeung, John H K

    2006-09-01

    Polysaccharide peptide (PSP), isolated from Coriolus versicolor COV-1, has been previously shown to have immuno-stimulatory, anti-tumour and analgesic effects in animal models. When used as an adjunct in cancer chemotherapy in clinical trials carried out in China, PSP improved the quality of life in the patients by improving appetite and alleviating symptoms associated with cancer chemotherapy. In this study, the effects of non-toxic doses of PSP on phase I metabolism was investigated in the rat, using the conventional probe antipyrine. Acute PSP (3-5 micromol/kg, i.p.) treatment did not produce significant changes in antipyrine clearance. Sub-chronic treatment with PSP (1-3 micromol/kg/day, i.p., 3 days) decreased the antipyrine clearance (30-35%), with an increase in the plasma half-life (T1/2) by 55% and an increase in the area under concentration-time curve (AUC) by 61%. Total hepatic cytochrome P450 (P450) was dose-dependently decreased (32-54%) after sub-chronic, but not the acute treatment of PSP. Given that PSP can affect phase I metabolism and hepatic cytochrome P450 content, the concomitant use of PSP with other therapeutic agents that undergo phase I metabolism should be carefully monitored.

  1. Clearance Prediction of Targeted Covalent Inhibitors by In Vitro-In Vivo Extrapolation of Hepatic and Extrahepatic Clearance Mechanisms.

    PubMed

    Leung, Louis; Yang, Xin; Strelevitz, Timothy J; Montgomery, Justin; Brown, Matthew F; Zientek, Michael A; Banfield, Christopher; Gilbert, Adam M; Thorarensen, Atli; Dowty, Martin E

    2017-01-01

    The concept of target-specific covalent enzyme inhibitors appears attractive from both an efficacy and a selectivity viewpoint considering the potential for enhanced biochemical efficiency associated with an irreversible mechanism. Aside from potential safety concerns, clearance prediction of covalent inhibitors represents a unique challenge due to the inclusion of nontraditional metabolic pathways of direct conjugation with glutathione (GSH) or via GSH S-transferase-mediated processes. In this article, a novel pharmacokinetic algorithm was developed using a series of Pfizer kinase selective acrylamide covalent inhibitors based on their in vitro-in vivo extrapolation of systemic clearance in rats. The algorithm encompasses the use of hepatocytes as an in vitro model for hepatic clearance due to oxidative metabolism and GSH conjugation, and the use of whole blood as an in vitro surrogate for GSH conjugation in extrahepatic tissues. Initial evaluations with clinical covalent inhibitors suggested that the scaling algorithm developed from rats may also be useful for human clearance prediction when species-specific parameters, such as hepatocyte and blood stability and blood binding, were considered. With careful consideration of clearance mechanisms, the described in vitro-in vivo extrapolation approach may be useful to facilitate candidate optimization, selection, and prediction of human pharmacokinetic clearance during the discovery and development of targeted covalent inhibitors.

  2. Immediate intralipid clearance from plasma in critically ill patients after a single-dose injection

    SciTech Connect

    Lindh, A.; Roessner, S.

    1987-09-01

    Plasma fractional removal rates (k2) of Intralipid injected in parallel with /sup 125/I albumin were analyzed in five healthy males and nine critically ill patients. The k2 values of critically ill patients were similar to those of healthy subjects. However, the initial plasma concentrations of Intralipid calculated by extrapolation to zero-time (y0) were markedly different. The mean y0 value in the critically ill patients was 43% that of healthy subjects. No plasma loss of /sup 125/I albumin occurred throughout the test. Intralipid to /sup 125/I albumin plasma concentration ratios during the removal phase paralleled the curves obtained from the iv fat tolerance test. This suggests that these ratios depend on Intralipid clearance rather than leakage from the circulation. The immediate loss of Intralipid suggests that the pulmonary vasculature, the first capillary bed through which the emulsion passes, could be the site where a substantial uptake of the emulsion occurs in critically ill patients.

  3. Clearance and binding of native and defucosylated lactoferrin.

    PubMed Central

    Imber, M J; Pizzo, S V

    1983-01-01

    These studies explore the role of carbohydrate recognition systems and the direct involvement of terminal alpha 1-3-linked fucose in the clearance of lactoferrin from the murine circulation and in the specific binding of lactoferrin to receptors on murine peritoneal macrophages. As previously reported, radiolabelled lactoferrin cleared very rapidly (t1/2 less than 1 min) after intravenous injection into mice. However, competing levels of ligands specific for the hepatic galactose receptor (asialo-orosomucoid), the hepatic fucose receptor (fucosyl-bovine serum albumin), and the mononuclear-phagocyte system pathway recognizing mannose, N-acetylglucosamine and fucose (mannosyl-, N-acetylglucosaminyl- and fucosyl-bovine serum albumin) did not block radiolabelled lactoferrin clearance in vivo or binding to mouse peritoneal macrophage monolayers in vitro. Almond emulsin alpha 1-3-fucosidase was used to prepare defucosylated lactoferrin in which 88% of the alpha 1-3-linked fucose was hydrolysed. No difference in clearance or receptor binding was observed between radiolabelled native and defucosylated lactoferrin. Fucoidin, a fucose-rich algal polysaccharide, completely inhibits the clearance in vivo and macrophage binding in vitro of lactoferrin. This effect, however, is probably not the result of competition for binding to the fucose receptor, since gel-filtration studies demonstrated formation of a stable complex between lactoferrin and fucoidin. The present results indicate that the lactoferrin-clearance pathway is distinct from several pathways mediating glycoprotein clearance through recognition of terminal galactose, fucose, N-acetylglucosamine or mannose. Furthermore, alpha 1-3-linked fucose on lactoferrin is not essential for lactoferrin clearance in vivo or specific binding to macrophage receptors in vitro. Images Fig. 3. PMID:6882370

  4. Tissue distribution and clearance of intravenously administered titanium dioxide (TiO2) nanoparticles.

    PubMed

    Shinohara, Naohide; Danno, Nobuko; Ichinose, Takayuki; Sasaki, Takeshi; Fukui, Hiroko; Honda, Kazumasa; Gamo, Masashi

    2014-03-01

    The organ-tissue distribution and clearance of Degussa P25 TiO2 nanoparticles were determined after intravenous administration to rats (0.95 mg/kg bodyweight) using an inductively coupled plasma sector field mass spectrometer. The detection limits of Ti analysis, 0.54 and 1.4 ng/mL for blood and urine and 0.35-2.0 ng/g tissue for several organ tissues, enabled determination of tissue distribution and clearance for organs in which Ti content could not be previously determined due to low concentrations. Blood concentrations of TiO2 were 420 and 19 ng/mL at 5 and 15 min after administration, which were equivalent of only 2.8% and 0.13% of the administration dose, respectively. At 6 h, 94%, 2.0%, 0.17%, 0.023%, 0.014% and 0.026% of administered TiO2 was found in the liver, spleen, lung, kidney, heart and blood, respectively. Liver and spleen TiO2 burden was significantly higher in the administration than control group (p < 0.01) and did not decrease up to 30 days after administration, while TiO2 burden in the lung, kidney, heart and blood decreased over time. A two-step decay model was more suitable than a one-step decay model for the decay curves of pulmonary TiO2 burden but did not improve fitting to the decay curves of kidney TiO2 burden. No translocation to the brain was confirmed at a lower detection limit than was applied in previous studies. Ti content in faeces and urine in the TiO2 administration group did not differ from that in the control group.

  5. [The equivalent renal urea clearance. Its relationship with mortality in chronic hemodialysed patients].

    PubMed

    Barreneche, M; Carreras, R; Leanza, H J; Najún Zarazaga, C J

    1999-01-01

    The Equivalent Renal Urea Clearance (EKR) integrates the residual renal function (KR) and the dialysis dose (Kt/V). The present study was performed with these objectives: to calculate EKR in our hemodialysis (HD) patients during a three year follow up, to define its relationship with mortality and to compare its importance as a risk factor among others and to calculate actuarial survival. We analyzed 267 chronic HD patients. We measured Kt/V single pool, TACu, albumin, creatinine, hemoglobin and HD time and we calculated KR, EKR, KRc and EKRc (the last two corrected for V* 401--to compare clearances of different size patients). The EKRc median was 14.20 ml/min and it was taken as cut off point. The mortality OR was 2.17. The multivariated analysis showed, as independent mortality predictors, the albumin (the most significant), the EKRc and the HD time. The actuarial survival of EKRc, Kt/V and albumin showed marked similarity of their curves. The significant differences between the predictor curves began on the 2nd year of HD, for albumin they began in levels lesser than 3.5 g/dl and higher than 3.4 g/dl. Therefore, we consider that the best advantage of EKRc, compared to other parameters derived from the urea kinetics model, was the possibility to valuate the weekly HD adequation (once, twice or three times a week) and this, depending on the KR and the Kt/V of each HD treatment. Besides, the EKRc could also be used as adequacy criterion in CAPD considering daily Kt/V so that we could employ EKRc as adequacy parameter for both replacement therapies.

  6. Accelerating Around an Unbanked Curve

    DTIC Science & Technology

    2006-02-01

    FEB 2006 2. REPORT TYPE 3. DATES COVERED 00-00-2006 to 00-00-2006 4. TITLE AND SUBTITLE Accelerating Around an Unbanked Curve 5a. CONTRACT...December 2004 issue of TPT presented a problem concerning how a car should acceler-ate around an unbanked curve of constant radius r starting from rest...Accelerating Around an Unbanked Curve Carl E. Mungan, U.S. Naval Academy, Annapolis, MD 100 THE PHYSICS TEACHER ◆ Vol. 44, February 2006 The shapes

  7. Curved conveyor section guide assembly

    SciTech Connect

    Truszczinski, H.

    1981-02-03

    A guide assembly for a curved conveyor section of a scraperchain conveyor guides the scraper assembly from a first straight conveyor portion round the curved conveyor section to a second straight conveyor portion. This guiding is accomplished by a pair of independently rotatable pulley wheels. A further pair of independently rotatable pulley wheels are provided to guide the drive chain of a plough round the curved conveyor section. This enables the plough to be driven to and fro along the first straight conveyor portion by a drive station attached to the second straight conveyor portion adjacent to the guide assembly.

  8. Acute effects of ethanol on renal folate clearance in rats

    SciTech Connect

    Eisenga, B.H.; McMartin, K.E.

    1986-03-05

    Studies of the renal clearance of folic acid in primates demonstrate net reabsorption of folate by a saturable system. The acute administration of ethanol to rats causes a significant increase in urinary folate excretion. The mechanism for this effect is unknown and thus the effect of acute administration of ethanol on the renal absorption and urinary clearance of folate was studied in rats. Folic acid was administered to male Sprague-Dawley rats via continuous intravenous infusion in doses ranging from 3-75 micromoles/kg and renal clearance relative to inulin was determined. The effects of various dose levels of ethanol on these parameters were then determined. At a dose of 15 micromoles/kg, the renal clearance of folate relative to that of inulin was about 0.65 mg/min. At a plasma ethanol level about 100 mg/dl, the renal clearance of folate was not markedly altered. These results suggests that there is net reabsorption of folate in the rat kidney and that moderate doses of ethanol have little effect on renal effect on renal folate reabsorption.

  9. Flow over riblet curved surfaces

    NASA Astrophysics Data System (ADS)

    Loureiro, J. B. R.; Silva Freire, A. P.

    2011-12-01

    The present work studies the mechanics of turbulent drag reduction over curved surfaces by riblets. The effects of surface modification on flow separation over steep and smooth curved surfaces are investigated. Four types of two-dimensional surfaces are studied based on the morphometric parameters that describe the body of a blue whale. Local measurements of mean velocity and turbulence profiles are obtained through laser Doppler anemometry (LDA) and particle image velocimetry (PIV).

  10. Impaired lipid clearance in patients with previous acute pancreatitis.

    PubMed Central

    Guzmán, S; Nervi, F; Llanos, O; León, P; Valdivieso, V

    1985-01-01

    Fasting serum triglycerides were measured in 52 patients who had sustained an attack of pancreatitis (gall stone related 33, alcoholism six) at least six months earlier. Several patients (23%) had raised fasting serum triglycerides, with a type IV phenotype in all but one patient. The 40 patients with normal fasting serum triglycerides received an oral load of 100 g sunflower oil to compare their clearance of dietary triglycerides with that of a control group of 54 subjects. The clearance of ingested triglycerides was significantly impaired in the patients - irrespective of the presumed aetiological factor, or clinical condition associated with pancreatitis - compared with the clearance in controls. A triglyceride tolerance test is the only way to detect those patients in whom a future attack of pancreatitis may be precipitated by a diet rich in fat, or endogenous over production of triglycerides as after an alcoholic debauch. PMID:4029716

  11. Application of Dsm in Obstacle Clearance Surveying of Aerodrome

    NASA Astrophysics Data System (ADS)

    Qiao, X.; Lv, S. H.; Li, L. L.; Zhou, X. J.; Wang, H. Y.; Li, D.; Liu, J. Y.

    2016-06-01

    Compared to the wide use of digital elevation model (DEM), digital surface model (DSM) receives less attention because that it is composed by not only terrain surface, but also vegetations and man-made objects which are usually regarded as useless information. Nevertheless, these objects are useful for the identification of obstacles around an aerodrome. The primary objective of the study was to determine the applicability of DSM in obstacle clearance surveying of aerodrome. According to the requirements of obstacle clearance surveying at QT airport, aerial and satellite imagery were used to generate DSM, by means of photogrammetry, which was spatially analyzed with the hypothetical 3D obstacle limitation surfaces (OLS) to identify the potential obstacles. Field surveying was then carried out to retrieve the accurate horizontal position and height of the obstacles. The results proved that the application of DSM could make considerable improvement in the efficiency of obstacle clearance surveying of aerodrome.

  12. Fiber-optic laser Doppler turbine tip clearance probe.

    PubMed

    Büttner, Lars; Pfister, Thorsten; Czarske, Jürgen

    2006-05-01

    A laser Doppler based method for in situ single blade tip clearance measurements of turbomachines with high precision is presented for what we believe is the first time. The sensor is based on two superposed fanlike interference fringe systems generated by two laser wavelengths from a fiber-coupled, passive, and therefore compact measurement head employing diffractive optics. Tip clearance measurements at a transonic centrifugal compressor performed during operation at 50,000 rpm (833 Hz, 586 m/s tip speed) are reported. At these speeds the measured uncertainty of the tip position was less than 20 microm, a factor of 2 more accurate than that of capacitive probes. The sensor offers great potential for in situ and online high-precision tip clearance measurements of metallic and nonmetallic turbine blades.

  13. Tumor Presence Induces Global Immune Changes and Enhances Nanoparticle Clearance.

    PubMed

    Kai, Marc P; Brighton, Hailey E; Fromen, Catherine A; Shen, Tammy W; Luft, J Christopher; Luft, Yancey E; Keeler, Amanda W; Robbins, Gregory R; Ting, Jenny P Y; Zamboni, William C; Bear, James E; DeSimone, Joseph M

    2016-01-26

    Long-circulating nanoparticles are essential for increasing tumor accumulation to provide therapeutic efficacy. While it is known that tumor presence can alter the immune system, very few studies have explored this impact on nanoparticle circulation. In this report, we demonstrate how the presence of a tumor can change the local and global immune system, which dramatically increases particle clearance. We found that tumor presence significantly increased clearance of PRINT hydrogel nanoparticles from the circulation, resulting in increased accumulation in the liver and spleen, due to an increase in M2-like macrophages. Our findings highlight the need to better understand interactions between immune status and nanoparticle clearance, and suggest that further consideration of immune function is required for success in preclinical and clinical nanoparticle studies.

  14. HPT Clearance Control: Intelligent Engine Systems-Phase 1

    NASA Technical Reports Server (NTRS)

    2005-01-01

    The following work has been completed to satisfy the Phase I Deliverables for the "HPT Clearance Control" project under NASA GRC's "Intelligent Engine Systems" program: (1) Need for the development of an advanced HPT ACC system has been very clearly laid out, (2) Several existing and potential clearance control systems have been reviewed, (3) A scorecard has been developed to document the system, performance (fuel burn, range, payload, etc.), thermal, and mechanical characteristics of the existing clearance control systems, (4) Engine size and flight cycle selection for the advanced HPT ACC system has been reviewed with "large engine"/"long range mission" combination showing the most benefit, (5) A scoring criteria has been developed to tie together performance parameters for an objective, data driven comparison of competing systems, and (6) The existing HPT ACC systems have been scored based on this scoring system.

  15. Dysregulation of Nutrient Sensing and CLEARance in Presenilin Deficiency.

    PubMed

    Reddy, Kavya; Cusack, Corey L; Nnah, Israel C; Khayati, Khoosheh; Saqcena, Chaitali; Huynh, Tuong B; Noggle, Scott A; Ballabio, Andrea; Dobrowolski, Radek

    2016-03-08

    Attenuated auto-lysosomal system has been associated with Alzheimer disease (AD), yet all underlying molecular mechanisms leading to this impairment are unknown. We show that the amino acid sensing of mechanistic target of rapamycin complex 1 (mTORC1) is dysregulated in cells deficient in presenilin, a protein associated with AD. In these cells, mTORC1 is constitutively tethered to lysosomal membranes, unresponsive to starvation, and inhibitory to TFEB-mediated clearance due to a reduction in Sestrin2 expression. Normalization of Sestrin2 levels through overexpression or elevation of nuclear calcium rescued mTORC1 tethering and initiated clearance. While CLEAR network attenuation in vivo results in buildup of amyloid, phospho-Tau, and neurodegeneration, presenilin-knockout fibroblasts and iPSC-derived AD human neurons fail to effectively initiate autophagy. These results propose an altered mechanism for nutrient sensing in presenilin deficiency and underline an importance of clearance pathways in the onset of AD.

  16. Clearance of inhaled ceramic fibers from rat lungs.

    PubMed Central

    Yamato, H; Tanaka, I; Higashi, T; Kido, M

    1994-01-01

    Deposition, clearance, retention, and durability of inhaled particles in lung are important factors for induction of pulmonary fibrosis or lung cancer. To study the deposition and clearance of aluminium silicate ceramic fibers from the lung, male Wistar rats were exposed to ceramic fibers, with a mass median aerodynamic diameter (MMAD) of 3.7 microns, for 6 hr/day, 5 days/week for 2 weeks. The average exposure concentration was 27.2 mg/m3 (SD 9.0). The rats were killed at 1 day, 1 month, 3 months, and 6 months after the end of exposure, and the fiber numbers and dimensions were measured with a scanning electron microscope. No significant difference in length of residual ceramic fibers in the lungs was found among the groups. The geometric mean diameter and number of ceramic fibers, however, decreased according to the clearance period. These findings suggest that the fibers were dissolved at their surface. PMID:7882924

  17. Acute exposure to acid fog. Effects on mucociliary clearance

    SciTech Connect

    Laube, B.L.; Bowes, S.M. III; Links, J.M.; Thomas, K.K.; Frank, R. )

    1993-05-01

    Submicrometric sulfuric acid (H2SO4) aerosol can affect mucociliary clearance without eliciting irritative symptoms or changes in pulmonary function. The effect of larger fog droplets containing H2SO4 on mucociliary clearance is unknown. We quantified mucociliary clearance from the trachea (n = 4) and small airways (n = 7) of young healthy male adults after an acute exposure to H2SO4 fog (MMAD = 10.3 microns; pH = 2.0; liquid water content = 481 +/- 65 mg/m3; osmolarity = 30 mOsm). Acid fog (AF) or saline fog (SF) (10.9 microns; 492 +/- 116 mg/m3; 30 mOsm) was administered for 40 min of unencumbered breathing (no mouth-piece) at rest and for 20 min of exercise sufficient to produce oronasal breathing. Fog exposures were followed by a methacholine (MCh) challenge (a measure of airway reactivity) or inhalation of technetium-99M radioaerosol (MMAD = 3.4 microns) on 2 study days each. Changes in symptoms and forced ventilatory function were also assessed. Clearance was quantified from computer-assisted analyses of gamma camera images of the lower respiratory tract in terms of %removal/min of the radiolabel from the trachea 25 min after inhalation and from the outer zone of the right lung after 1.9 to 3 h. Symptoms, forced ventilatory function, and MCh response were unaffected by either fog. Tracheal clearance was more rapid in four of four subjects after AF (0.83 +/- 1.58% removal/min) compared with that after SF (-0.54 +/- 0.85% removal/min). Outer zone clearance was more rapid in six of seven subjects after AF (0.22 +/- 0.15% removal/min) compared with that after SF (0.01 +/- 0.09% removal/min).

  18. Effects of desipramine on norepinephrine clearance in congestive heart failure

    SciTech Connect

    Clemson, B.; Baily, R.G.; Davis, D.; Zelis, R. )

    1990-08-01

    Elevated plasma norepinephrine (NE) in congestive heart failure (CHF) is caused by increased NE spillover and decreased NE clearance. To evaluate the effects of neuronal uptake blockade on NE clearance, we studied NE kinetics during steady-state infusions of (3H)NE, before and after oral desipramine (DMI, 50 mg) in 11 patients with CHF and 8 normal volunteers. Baseline plasma NE was greater in the CHF group (637 +/- 56 vs. 271 +/- 32 pg/ml; P less than 0.001), NE clearance was lower in CHF (1.31 +/- 0.21 vs. 1.94 +/- 0.17 l.min-1.m-2; P = 0.026), and NE spillover was greater in CHF (4.71 +/- 0.78 vs. 3.04 +/- 0.35 nmol.min-1.m-2, P = 0.054). After DMI, plasma NE rose significantly in CHF (778 +/- 67; P = 0.008), and NE clearance decreased further in CHF (0.97 +/- 0.16; P = 0.024), but neither changed in normal subjects. NE spillover did not change in either group. There appears to be an enhanced effect of DMI on NE clearance in CHF patients. Two general mechanisms may be responsible for this finding, an increased concentration of drug, possibly caused by a decreased volume of distribution, and an increased sensitivity of neuronal amine pumps to DMI. Both mechanisms may reflect a more general abnormality of clearance of drugs and hormones related to abnormalities of tissue perfusion in CHF.

  19. Cochlear microphonic broad tuning curves

    NASA Astrophysics Data System (ADS)

    Ayat, Mohammad; Teal, Paul D.; Searchfield, Grant D.; Razali, Najwani

    2015-12-01

    It is known that the cochlear microphonic voltage exhibits much broader tuning than does the basilar membrane motion. The most commonly used explanation for this is that when an electrode is inserted at a particular point inside the scala media, the microphonic potentials of neighbouring hair cells have different phases, leading to cancelation at the electrodes location. In situ recording of functioning outer hair cells (OHCs) for investigating this hypothesis is exceptionally difficult. Therefore, to investigate the discrepancy between the tuning curves of the basilar membrane and those of the cochlear microphonic, and the effect of phase cancellation of adjacent hair cells on the broadness of the cochlear microphonic tuning curves, we use an electromechanical model of the cochlea to devise an experiment. We explore the effect of adjacent hair cells (i.e., longitudinal phase cancellation) on the broadness of the cochlear microphonic tuning curves in different locations. The results of the experiment indicate that active longitudinal coupling (i.e., coupling with active adjacent outer hair cells) only slightly changes the broadness of the CM tuning curves. The results also demonstrate that there is a π phase difference between the potentials produced by the hair bundle and the soma near the place associated with the characteristic frequency based on place-frequency maps (i.e., the best place). We suggest that the transversal phase cancellation (caused by the phase difference between the hair bundle and the soma) plays a far more important role than longitudinal phase cancellation in the broadness of the cochlear microphonic tuning curves. Moreover, by increasing the modelled longitudinal resistance resulting the cochlear microphonic curves exhibiting sharper tuning. The results of the simulations suggest that the passive network of the organ of Corti determines the phase difference between the hair bundle and soma, and hence determines the sharpness of the

  20. Effect of atropine on oral clearance of a radiolabeled sulfur colloid

    SciTech Connect

    LaForce, F.M.; Thompson, B.; Trow, R.

    1984-11-01

    Physical clearance is an important oral defense mechanism against gram-negative rods. The authors describe a simple technique that uses commercially available technetium-99m sulfur colloid to measure oral clearance. Technetium-99m sulfur colloid was sprayed into the mouth, and clearance was measured as the percent decrease in radiolabel counts over 2 hours using a radioisotope camera. Results using this technique compared favorably with clearance data using Tc-99m radiolabeled Escherichia coli. Atropine significantly decreased oral clearance rates of the colloid. Decreased clearance may be an important risk factor in the development of gram-negative rod colonization in hospitalized patients. 15 references, 3 figures.

  1. Mannitol clearance for the determination of glomerular filtration rate-a validation against clearance of (51) Cr-EDTA.

    PubMed

    Kiss, Katalin; Molnár, Miklós; Söndergaard, Sören; Molnár, Gyula; Ricksten, Sven-Erik

    2016-06-03

    We studied the agreement between plasma clearance of mannitol and the reference method, plasma clearance of (51) Cr-EDTA in outpatients with normal to moderately impaired renal function. Forty-one patients with a serum creatinine <200 μmol l(-1) entered the study. (51) Cr-EDTA clearance was measured with the standard bolus injection technique and glomerular filtration rate (GFR) was calculated by the single-sample method described by Jacobsson. Mannitol, 0·25 g kg(-1) body weight (150 mg ml(-1) ), was infused for 4-14 min and blood samples taken at 1-, 2-, 3- and 4-h (n = 24) or 2-, 3-, 3·5- and 4-h after infusion (n = 17). Mannitol in serum was measured by an enzymatic method. Plasma clearance for mannitol and its apparent volume of distribution (Vd) were calculated according to Brøchner-Mortensen. Mean plasma clearance (±SD) for (51) Cr-EDTA was 59·7 ± 18·8 ml min(-1) . The mean plasma clearance for mannitol ranged between 57·0 ± 20·1 and 61·1 ± 16·7 ml min(-1) and Vd was 21·3 ± 6·2% per kg b.w. The between-method bias ranged between -0·23 and 2·73 ml min(-1) , the percentage error between 26·7 and 39·5% and the limits of agreement between -14·3/17·2 and -25·3/19·9 ml min(-1) . The best agreement was seen when three- or four-sample measurements of plasma mannitol were obtained and when sampling started 60 min after injection. Furthermore, accuracy of plasma clearance determinations was 88-96% (P30) and 41-63% (P10) and was highest when three- or four-sample measurements of plasma mannitol were obtained, including the first hour after the bolus dose. We conclude that there is a good agreement between plasma clearances of mannitol and (51) Cr-EDTA for the assessment of GFR.

  2. Relative Locality in Curved Spacetime

    NASA Astrophysics Data System (ADS)

    Kowalski-Glikman, Jerzy; Rosati, Giacomo

    2013-07-01

    In this paper we construct the action describing dynamics of the particle moving in curved spacetime, with a nontrivial momentum space geometry. Curved momentum space is the core feature of theories where relative locality effects are present. So far aspects of nonlinearities in momentum space have been studied only for flat or constantly expanding (de Sitter) spacetimes, relying on their maximally symmetric nature. The extension of curved momentum space frameworks to arbitrary spacetime geometries could be relevant for the opportunities to test Planck-scale curvature/deformation of particles momentum space. As a first example of this construction we describe the particle with κ-Poincaré momentum space on a circular orbit in Schwarzschild spacetime, where the contributes of momentum space curvature turn out to be negligible. The analysis of this problem relies crucially on the solution of the soccer ball problem.

  3. Phase nucleation in curved space

    NASA Astrophysics Data System (ADS)

    Gómez, Leopoldo; García, Nicolás; Vitelli, Vincenzo; Lorenzana, José; Daniel, Vega

    Nucleation and growth is the dominant relaxation mechanism driving first-order phase transitions. In two-dimensional flat systems, nucleation has been applied to a wide range of problems in physics, chemistry and biology. Here we study nucleation and growth of two-dimensional phases lying on curved surfaces and show that curvature modifies both critical sizes of nuclei and paths towards the equilibrium phase. In curved space, nucleation and growth becomes inherently inhomogeneous and critical nuclei form faster on regions of positive Gaussian curvature. Substrates of varying shape display complex energy landscapes with several geometry-induced local minima, where initially propagating nuclei become stabilized and trapped by the underlying curvature (Gómez, L. R. et al. Phase nucleation in curved space. Nat. Commun. 6:6856 doi: 10.1038/ncomms7856 (2015).).

  4. Supply curves of conserved energy

    NASA Astrophysics Data System (ADS)

    Meier, A. K.

    1982-05-01

    Supply curves of conserved energy provide an accounting framework that expresses the potential for energy conservation. The economic worthiness of a conservation measure is expressed in terms of the cost of conserved energy, and a measure is considered economical when the cost of conserved energy is less than the price of the energy it replaces. A supply curve of conserved energy is independent of energy prices; however, the economical reserves of conserved energy will depend on energy prices. Double-counting of energy savings and error propagation are common problems when estimating conservation potentials, but supply curves minimize these difficulties and make their consequences predictable. The sensitivity of the cost of conserved energy is examined, as are variations in the optimal investment strategy in response to changes in inputs. Guidelines are presented for predicting the consequences of such changes.

  5. Curve Fit Technique for a Smooth Curve Using Gaussian Sections.

    DTIC Science & Technology

    1983-08-01

    curve-fitting. Furthermore, the algorithm that does the fitting is simple enough to be used on a programmable calculator . 8 -I.F , A X i 4. Y-14 .4. - -* F.J OR;r IF 17 r*~~ , ac ~J ’a vt. . S ~ :.. *~All, a-4k .16’.- a1 1, t

  6. Mine Clearance Industry: Background, Geography, Funding, Analysis and Future Projections

    DTIC Science & Technology

    2007-12-01

    July 1998. 31 Paul K. Walker, Engineers of Independence, A Documentary History of the Army Engineers in the American Revolution, 1775-1783, (Honolulu...capability. Evaluation is a combination of documentary evidence and practical ability. Theatre specific Techniques/Procedures and Standards...Clearance and Detection, Bolivia, Bosnia- Herzegovina, 218 Jesuit Refugee Service NGO/INGO Humanitarian Coordination, Angola, Australia

  7. 30 CFR 57.9306 - Warning devices for restricted clearances.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... creates a hazard to persons on mobile equipment, warning devices shall be installed in advance of the... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Warning devices for restricted clearances. 57... Loading, Hauling, and Dumping Safety Devices, Provisions, and Procedures for Roadways, Railroads,...

  8. 30 CFR 56.9306 - Warning devices for restricted clearances.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... creates a hazard to persons on mobile equipment, warning devices shall be installed in advance of the... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Warning devices for restricted clearances. 56... Loading, Hauling, and Dumping Safety Devices, Provisions, and Procedures for Roadways, Railroads,...

  9. Highly fluorescent resorcinarene cavitand nanocapsules with efficient renal clearance

    NASA Astrophysics Data System (ADS)

    Mahadevan, Kalpana; Patthipati, Venkata Suresh; Han, Sangbum; Swanson, R. James; Whelan, Eoin C.; Osgood, Christopher; Balasubramanian, Ramjee

    2016-08-01

    Nanomaterial based imaging approaches hold substantial promise in addressing current diagnostic and therapeutic challenges. One of the key requirements for the successful clinical translation of nanomaterials is their complete clearance from the body within a reasonable time period preferably via the renal filtration route. This article describes the synthesis of highly fluorescent, water soluble, resorcinarene cavitand nanocapsules and demonstrates their effective renal clearance in mice. The synthesis and functionalization of nanocapsules was accomplished in a one-pot operation via thiol-ene reactions without involving self-assembly, sacrificial templates or emulsions. Water soluble resorcinarene cavitand nanocapsules obtained by this approach were covalently functionalized with Alexa Fluor 750. Highly fluorescent nanocapsules with hydrodynamic diameters of 122 nm and 68 nm and extinction coefficients of 1.3 × 109 M-1 cm-1 and 1.5 × 108 M-1 cm-1 respectively were prepared by varying the reaction conditions. The in vivo biodistribution and clearance of these nanocapsules in mice followed by whole-body fluorescence imaging showed that they were both cleared renally within a few hours. Given the inherent encapsulation capabilities of nanocapsules, the renal clearance demonstrated in this work opens up new opportunities for their theranostic applications especially for targeting and treating the urinary tract.

  10. Tracheobronchial mucociliary clearance in asthma: impairment during remission.

    PubMed Central

    Pavia, D; Bateman, J R; Sheahan, N F; Agnew, J E; Clarke, S W

    1985-01-01

    Tracheobronchial mucociliary clearance was measured in eight non-smoking patients with asthma in complete remission. The patients were symptom free and required no medication whatsoever for one to six months before assessment. Mucociliary clearance was measured with an objective, radioaerosol technique. For comparison, mucociliary clearance of eight non-smoking, healthy subjects with physical characteristics and pulmonary function similar to those of the asthmatics was also measured on two occasions. In their first assessment the healthy subjects inhaled the tracer radioaerosol under experimental conditions similar to those used for the asthmatics; in the second assessment they inhaled the radioaerosol rapidly to simulate the asthmatic pattern of deposition. Under similar experimental conditions the radioaerosol was deposited more proximally in the asthmatic subjects than in the normal subjects and the difference was statistically significant (p less than 0.01). When, however, the depth of radioaerosol lung penetration was similar in the two groups, there was evidence of a significantly (p less than 0.01) poorer mucociliary clearance six hours after radioaerosol inhalation in the asthmatic than in the healthy group. These findings raise the question whether asthma ever remits completely. PMID:3983883

  11. Modifications of lung clearance mechanisms by acute influenza A infection

    SciTech Connect

    Levandowski, R.A.; Gerrity, T.R.; Garrard, C.S.

    1985-10-01

    Four volunteers with naturally acquired, culture-proved influenza A infection inhaled a radiolabeled aerosol to permit investigation of lung mucociliary clearance mechanisms during and after symptomatic illness. Mucus transport in the trachea was undetectable when monitored with an external multidetector probe within 48 hours of the onset of the illness, but was found at a normal velocity by 1 week in three of the four subjects. In two volunteers who coughed 23 to 48 times during the 4.5-hour observation period, whole lung clearance was as fast within the first 48 hours of illness as during health 3 months later in spite of the absence of measurable tracheal mucus transport. Conversely, in spite of the return 1 week later of mucus transport at velocities expected in the trachea, whole lung clearance for the 4.5-hour period was slowed in two volunteers who coughed less than once an hour. The data offer evidence that cough is important in maintaining lung clearance for at least several days after symptomatic influenza A infection when other mechanisms that depend on ciliary function are severely deficient.

  12. 50 CFR 14.53 - Detention and refusal of clearance.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 50 Wildlife and Fisheries 1 2010-10-01 2010-10-01 false Detention and refusal of clearance. 14.53 Section 14.53 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR TAKING, POSSESSION, TRANSPORTATION, SALE, PURCHASE, BARTER, EXPORTATION, AND IMPORTATION OF WILDLIFE...

  13. 50 CFR 14.52 - Clearance of imported wildlife.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 50 Wildlife and Fisheries 1 2010-10-01 2010-10-01 false Clearance of imported wildlife. 14.52 Section 14.52 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR TAKING, POSSESSION, TRANSPORTATION, SALE, PURCHASE, BARTER, EXPORTATION, AND IMPORTATION OF WILDLIFE...

  14. Spontaneous Clearance of Viral Infections by Mesoscopic Fluctuations

    PubMed Central

    Chaudhury, Srabanti; Perelson, Alan S.; Sinitstyn, Nikolai A.

    2012-01-01

    Spontaneous disease extinction can occur due to a rare stochastic fluctuation. We explore this process, both numerically and theoretically, in two minimal models of stochastic viral infection dynamics. We propose a method that reduces the complexity in models of viral infections so that the remaining dynamics can be studied by previously developed techniques for analyzing epidemiological models. Using this technique, we obtain an expression for the infection clearance time as a function of kinetic parameters. We apply our theoretical results to study stochastic infection clearance for specific stages of HIV and HCV dynamics. Our results show that the typical time for stochastic clearance of a viral infection increases exponentially with the size of the population, but infection still can be cleared spontaneously within a reasonable time interval in a certain population of cells. We also show that the clearance time is exponentially sensitive to the viral decay rate and viral infectivity but only linearly dependent on the lifetime of an infected cell. This suggests that if standard drug therapy fails to clear an infection then intensifying therapy by adding a drug that reduces the rate of cell infection rather than immune modulators that hasten infected cell death may be more useful in ultimately clearing remaining pockets of infection. PMID:22693646

  15. Celllular Uptake and Clearance of TIO2 Nanoparticles

    EPA Science Inventory

    Differential rates of cellular uptake and clearance of engineered nanomaterials may influence the propensity for tissue accumulation under chronic exposure conditions. A retinal pigment epithelial cell line (ARPE-19) was used to investigate 1) if Ti02 (Degussa, P25) nanoparticles...

  16. Functional interferon system is required for clearance of lassa virus.

    PubMed

    Yun, Nadezhda E; Poussard, Allison L; Seregin, Alexey V; Walker, Aida G; Smith, Jennifer K; Aronson, Judith F; Smith, Jeanon N; Soong, Lynn; Paessler, Slobodan

    2012-03-01

    Lassa virus (LASV) is the causative agent of Lassa hemorrhagic fever (LF) in humans, a deadly disease endemic to West Africa that results in 5,000 to 10,000 deaths annually. Here we present results demonstrating that functional type I and type II interferon (IFN) signaling is required for efficient control of LASV dissemination and clearance.

  17. [Airway clearance techniques in chronic obstructive pulmonary syndrome : 2011 update].

    PubMed

    Opdekamp, C

    2011-09-01

    For many years the airway clearance techniques used in chest physical therapy were assimilated with the singular technique of postural drainage, percussions and vibrations. However the side effects and counter indications and the lack of scientific proof regarding this technique have forced reflection and development of other techniques more comfortable and without deleterious effects. If all these techniques show a high efficiency in terms of improved mucociliary clearance, the literature is unanimous on how little effect these techniques have in the short and the long-term with regards to lung function and arterial blood gases. In view of the scientific literature, it is clear that the airway clearance techniques don't have the same recognition concerning their efficiency in all obstructive pulmonary diseases. As the cornerstone in the management of cystic fibrosis, the efficiency of the bronchial hygiene techniques are in general poorly documented in the management of the non-cystic fibrosis bronchiectasis, bronchitis or emphysema. The use of the chest physical therapy seems more to do with the interpretation of the imagery and symptomatology. The airway clearance techniques should be individualised according to symptoms, the amount of expectorated mucus and the objectives signs of secretions retention or subjective signs of difficulty expectorating secretions with progression of the disease.

  18. 7 CFR 1927.55 - Title clearance services.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 12 2013-01-01 2013-01-01 false Title clearance services. 1927.55 Section 1927.55 Agriculture Regulations of the Department of Agriculture (Continued) RURAL HOUSING SERVICE, RURAL BUSINESS-COOPERATIVE SERVICE, RURAL UTILITIES SERVICE, AND FARM SERVICE AGENCY, DEPARTMENT OF AGRICULTURE...

  19. An Examination of OMB Forms Clearance Aims, Policies and Procedures.

    ERIC Educational Resources Information Center

    Coan, Donald L.; Bertram, Charles L.

    The purposes of this paper are four-fold: (1) to delineate the principal aims and policy objectives of Office of Management and Budget Forms Clearance (OMB FC), as embodied in Federal legislation and executive directives since 1942; (2) to identify the major current thrusts of OMB FC; (3) to suggest possible future policy directions of OMB FC,…

  20. Some Proposals Regarding Copyright Clearance and Digitisation in Higher Education.

    ERIC Educational Resources Information Center

    Bide, Mark; Oppenheim, Charles; Ramsden, Anne

    1997-01-01

    Examines issues of copyright clearance by British universities for digitizing published printed materials. Discusses types of digitization, pricing, contract language, "compliance culture," publishers' rights, terms of licenses, and developing a publishers'"code of practice," and proposes a matrix of uses and users to support…

  1. OMB Forms Clearance: Restrictions on Educational Research Plans.

    ERIC Educational Resources Information Center

    Coan, Donald L.

    Forms Clearance standards and regulations are used by the Office of Management and Budget and by the Education Division of the Department of Health, Education and Welfare in order to upgrade the quality of federal data collection, to minimize cost, minimize reporting burden, maximize utility, and to protect the privacy rights of respondents.…

  2. Royalty Fees Part I: The Copyright Clearance Center and Publishers.

    ERIC Educational Resources Information Center

    Eiblum, Paula; Ardito, Stephanie C.

    1998-01-01

    Discussion of copyrights, royalty fees, and intellectual property focuses on the Copyright Clearance Center and publishers. Topics include results of a survey of library and information science journal publishers; how users verify royalty fees; how publishers determine fees; royalty fee reporting; and terms and conditions imposed on electronic…

  3. Managing Copyright Clearance Services in Higher Education Libraries.

    ERIC Educational Resources Information Center

    Gadd, Elizabeth

    2001-01-01

    Investigated centralized copyright clearance services in higher education institutions based on the findings of a questionnaire survey and five case study interviews in United Kingdom libraries. Examines reasons why services were established, how they were funded and staffed, their overall remit, problems, and good practice guidelines. (Author/LRW)

  4. The Genesis and Justification of Forms Clearance Procedures.

    ERIC Educational Resources Information Center

    Duncan, Joseph W.; Wallman, Katherine K.

    The central reports clearance authority of the Federal Government is a legislatively sanctioned mechanism for applying constraints on the conduct of statistical and other data gathering activities by Federal Departments and agencies and other research parties funded by Federal government contracts. General recommendations for improving the overall…

  5. Seal Investigations of an Active Clearance Control System Concept

    NASA Technical Reports Server (NTRS)

    Steinetz, Bruce M.; Taylor, Shawn; Oswald, Jay; DeCastro, Jonathan A.

    2006-01-01

    In an effort to improve upon current thermal active clearance control methods, a first generation, fast-acting mechanically actuated, active clearance control system has been designed and installed into a non-rotating test rig. In order to harvest the benefit of tighter blade tip clearances, low-leakage seals are required for the actuated carrier segments of the seal shroud to prevent excessive leakage of compressor discharge (P3) cooling air. The test rig was designed and fabricated to facilitate the evaluation of these types of seals, identify seal leakage sources, and test other active clearance control system concepts. The objective of this paper is to present both experimental and analytical investigations into the nature of the face-seal to seal-carrier interface. Finite element analyses were used to examine face seal contact pressures and edge-loading under multiple loading conditions, varied E-seal positions and two new face seal heights. The analyses indicated that moving the E-seal inward radially and reducing face seal height would lead to more uniform contact conditions between the face seal and the carriers. Lab testing confirmed that moving the balance diameter inward radially caused a decrease in overall system leakage.

  6. 46 CFR 61.20-23 - Tailshaft clearance; bearing weardown.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 2 2012-10-01 2012-10-01 false Tailshaft clearance; bearing weardown. 61.20-23 Section...; bearing weardown. (a) Water lubricated bearings, other than rubber, must be rebushed as follows: (1) Where the propelling machinery is located amidship, the after stern tube bearing must be rebushed when it...

  7. 46 CFR 61.20-23 - Tailshaft clearance; bearing weardown.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 2 2011-10-01 2011-10-01 false Tailshaft clearance; bearing weardown. 61.20-23 Section...; bearing weardown. (a) Water lubricated bearings, other than rubber, must be rebushed as follows: (1) Where the propelling machinery is located amidship, the after stern tube bearing must be rebushed when it...

  8. 46 CFR 61.20-23 - Tailshaft clearance; bearing weardown.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Tailshaft clearance; bearing weardown. 61.20-23 Section...; bearing weardown. (a) Water lubricated bearings, other than rubber, must be rebushed as follows: (1) Where the propelling machinery is located amidship, the after stern tube bearing must be rebushed when it...

  9. 46 CFR 61.20-23 - Tailshaft clearance; bearing weardown.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 2 2014-10-01 2014-10-01 false Tailshaft clearance; bearing weardown. 61.20-23 Section...; bearing weardown. (a) Water lubricated bearings, other than rubber, must be rebushed as follows: (1) Where the propelling machinery is located amidship, the after stern tube bearing must be rebushed when it...

  10. 46 CFR 61.20-23 - Tailshaft clearance; bearing weardown.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 2 2013-10-01 2013-10-01 false Tailshaft clearance; bearing weardown. 61.20-23 Section...; bearing weardown. (a) Water lubricated bearings, other than rubber, must be rebushed as follows: (1) Where the propelling machinery is located amidship, the after stern tube bearing must be rebushed when it...

  11. Influence of clearance model on numerical simulation of centrifugal pump

    NASA Astrophysics Data System (ADS)

    Wang, Z.; Gao, B.; Yang, L.; Du, W. Q.

    2016-05-01

    Computing models are always simplified to save the computing resources and time. Particularly, the clearance that between impeller and pump casing is always ignored. But the completer model is, the more precise result of numerical simulation is in theory. This paper study the influence of clearance model on numerical simulation of centrifugal pump. We present such influence via comparing performance, flow characteristic and pressure pulsation of two cases that the one of two cases is the model pump with clearance and the other is not. And the results show that the head decreases and power increases so that efficiency decreases after computing with front and back cavities. Then no-leakage model would improve absolute velocity magnitude in order to reach the rated flow rate. Finally, more disturbance induced by front cavity flow and wear-ring flow would change the pressure pulsation of impeller and volute. The performance of clearance flow is important for the whole pump in performance, flow characteristic, pressure pulsation and other respects.

  12. Highly fluorescent resorcinarene cavitand nanocapsules with efficient renal clearance.

    PubMed

    Mahadevan, Kalpana; Patthipati, Venkata Suresh; Han, Sangbum; Swanson, R James; Whelan, Eoin C; Osgood, Christopher; Balasubramanian, Ramjee

    2016-08-19

    Nanomaterial based imaging approaches hold substantial promise in addressing current diagnostic and therapeutic challenges. One of the key requirements for the successful clinical translation of nanomaterials is their complete clearance from the body within a reasonable time period preferably via the renal filtration route. This article describes the synthesis of highly fluorescent, water soluble, resorcinarene cavitand nanocapsules and demonstrates their effective renal clearance in mice. The synthesis and functionalization of nanocapsules was accomplished in a one-pot operation via thiol-ene reactions without involving self-assembly, sacrificial templates or emulsions. Water soluble resorcinarene cavitand nanocapsules obtained by this approach were covalently functionalized with Alexa Fluor 750. Highly fluorescent nanocapsules with hydrodynamic diameters of 122 nm and 68 nm and extinction coefficients of 1.3 × 10(9) M(-1) cm(-1) and 1.5 × 10(8) M(-1) cm(-1) respectively were prepared by varying the reaction conditions. The in vivo biodistribution and clearance of these nanocapsules in mice followed by whole-body fluorescence imaging showed that they were both cleared renally within a few hours. Given the inherent encapsulation capabilities of nanocapsules, the renal clearance demonstrated in this work opens up new opportunities for their theranostic applications especially for targeting and treating the urinary tract.

  13. 78 FR 77027 - Overhead Clearance (Air-Draft) Accidents

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-12-20

    ... address the problem of overhead clearance (air-draft) accidents. In its petition, which calls for vessel... methods: (1) Federal eRulemaking Portal: http://www.regulations.gov . (2) Fax: 202-493-2251. (3) Mail..., ] contact LCDR William Nabach, Office of Vessel and Facility Operating Standards (CG-OES-2), U.S....

  14. 33 CFR 118.160 - Vertical clearance gauges.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... numerals and foot marks below “low steel” of the bridge whenever the gauge is repainted or the structure is... BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.160 Vertical clearance gauges. (a) When necessary for... distance between “low steel” of the bridge channel span (in the closed to navigation position...

  15. 48 CFR 801.602-76 - Business clearance review.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Business clearance review. 801.602-76 Section 801.602-76 Federal Acquisition Regulations System DEPARTMENT OF VETERANS AFFAIRS GENERAL DEPARTMENT OF VETERANS AFFAIRS ACQUISITION REGULATION SYSTEM Career Development,...

  16. 31 CFR 205.20 - What is a clearance pattern?

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 31 Money and Finance:Treasury 2 2011-07-01 2011-07-01 false What is a clearance pattern? 205.20 Section 205.20 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) FISCAL SERVICE, DEPARTMENT OF THE TREASURY FINANCIAL MANAGEMENT SERVICE RULES AND PROCEDURES FOR EFFICIENT FEDERAL-STATE FUNDS TRANSFERS Rules...

  17. 10 CFR 95.17 - Processing facility clearance.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... related classified information, or process the facility for a facility clearance. Processing will include... concerning the foreign intelligence threat, risk of unauthorized technology transfer, type and sensitivity of... acceptable security review conducted by the NRC; (3) Submitting key management personnel for...

  18. 23 CFR Appendix B to Part 1327 - OMB Clearance

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 23 Highways 1 2011-04-01 2011-04-01 false OMB Clearance B Appendix B to Part 1327 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PROCEDURES FOR PARTICIPATING IN AND RECEIVING INFORMATION FROM THE NATIONAL DRIVER REGISTER PROBLEM DRIVER POINTER SYSTEM Pt....

  19. 23 CFR Appendix B to Part 1327 - OMB Clearance

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 23 Highways 1 2014-04-01 2014-04-01 false OMB Clearance B Appendix B to Part 1327 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PROCEDURES FOR PARTICIPATING IN AND RECEIVING INFORMATION FROM THE NATIONAL DRIVER REGISTER PROBLEM DRIVER POINTER SYSTEM Pt....

  20. 23 CFR Appendix B to Part 1327 - OMB Clearance

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 23 Highways 1 2010-04-01 2010-04-01 false OMB Clearance B Appendix B to Part 1327 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PROCEDURES FOR PARTICIPATING IN AND RECEIVING INFORMATION FROM THE NATIONAL DRIVER REGISTER PROBLEM DRIVER POINTER SYSTEM Pt....

  1. 23 CFR Appendix B to Part 1327 - OMB Clearance

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 23 Highways 1 2012-04-01 2012-04-01 false OMB Clearance B Appendix B to Part 1327 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PROCEDURES FOR PARTICIPATING IN AND RECEIVING INFORMATION FROM THE NATIONAL DRIVER REGISTER PROBLEM DRIVER POINTER SYSTEM Pt....

  2. 23 CFR Appendix B to Part 1327 - OMB Clearance

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 23 Highways 1 2013-04-01 2013-04-01 false OMB Clearance B Appendix B to Part 1327 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PROCEDURES FOR PARTICIPATING IN AND RECEIVING INFORMATION FROM THE NATIONAL DRIVER REGISTER PROBLEM DRIVER POINTER SYSTEM Pt....

  3. 50 CFR 14.55 - Exceptions to clearance requirements.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... wildlife: (a) Shellfish and fishery products imported for purposes of human or animal consumption or taken... 50 Wildlife and Fisheries 1 2013-10-01 2013-10-01 false Exceptions to clearance requirements. 14.55 Section 14.55 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF...

  4. 50 CFR 14.55 - Exceptions to clearance requirements.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... wildlife: (a) Shellfish and fishery products imported for purposes of human or animal consumption or taken... 50 Wildlife and Fisheries 1 2011-10-01 2011-10-01 false Exceptions to clearance requirements. 14.55 Section 14.55 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF...

  5. 50 CFR 14.55 - Exceptions to clearance requirements.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... wildlife: (a) Shellfish and fishery products imported for purposes of human or animal consumption or taken... 50 Wildlife and Fisheries 1 2012-10-01 2012-10-01 false Exceptions to clearance requirements. 14.55 Section 14.55 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF...

  6. Determinant factor for clearance of ceramic fibres from rat lungs.

    PubMed Central

    Yamato, H; Tanaka, I; Higashi, T; Kido, M

    1992-01-01

    Deposition, clearance, retention, and durability of inhaled particles from lungs are known to be important factors for induction of pulmonary fibrosis or lung cancer. To study the deposition and clearance of alumina silicate ceramic fibres from the lung, male Wistar rats were exposed to ceramic fibre particles with a mass median aerodynamic diameter (MMAD) of 4.2 micron, for six hours a day, five days a week for two weeks. The average exposure concentration was 20.7 (standard deviation (SD) 4.5) mg/m3. The rats were killed at one day, three months, and six months after the end of exposure, and the fibre numbers and dimensions were measured with a scanning electron microscope. No significant differences in number and geometric mean length of residual ceramic fibres in the lungs were found between the groups. The geometric mean diameter, however, decreased according to the duration of the clearance period. These findings suggest that solubility of fibre contributes most in the clearance of the inhaled ceramic fibres from the lungs. PMID:1554614

  7. Determinant factor for clearance of ceramic fibres from rat lungs.

    PubMed

    Yamato, H; Tanaka, I; Higashi, T; Kido, M

    1992-03-01

    Deposition, clearance, retention, and durability of inhaled particles from lungs are known to be important factors for induction of pulmonary fibrosis or lung cancer. To study the deposition and clearance of alumina silicate ceramic fibres from the lung, male Wistar rats were exposed to ceramic fibre particles with a mass median aerodynamic diameter (MMAD) of 4.2 micron, for six hours a day, five days a week for two weeks. The average exposure concentration was 20.7 (standard deviation (SD) 4.5) mg/m3. The rats were killed at one day, three months, and six months after the end of exposure, and the fibre numbers and dimensions were measured with a scanning electron microscope. No significant differences in number and geometric mean length of residual ceramic fibres in the lungs were found between the groups. The geometric mean diameter, however, decreased according to the duration of the clearance period. These findings suggest that solubility of fibre contributes most in the clearance of the inhaled ceramic fibres from the lungs.

  8. 48 CFR 2452.237-75 - Clearance of contractor personnel.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... URBAN DEVELOPMENT CLAUSES AND FORMS SOLICITATION PROVISIONS AND CONTRACT CLAUSES Texts of Provisions and... clause in solicitations and contracts. Clearance of Contractor Personnel (OCT 1999) (a) General. This contract requires contractor employees to work in, and have access to, a HUD facility. All such...

  9. 19 CFR 4.61 - Requirements for clearance.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... vessels. (c) Verification of compliance. Before clearance is granted to a vessel bound to a foreign port... following matters: (1) Accounting for inward cargo (see § 4.62). (2) Outward Cargo Declarations; shippers.... Unless otherwise provided in this section, every vessel bound for a foreign port or ports will be...

  10. 49 CFR Appendix F to Part 512 - OMB Clearance

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 6 2010-10-01 2010-10-01 false OMB Clearance F Appendix F to Part 512 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION CONFIDENTIAL BUSINESS INFORMATION Pt. 512, App. F Appendix F to...

  11. 49 CFR Appendix F to Part 512 - OMB Clearance

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 6 2011-10-01 2011-10-01 false OMB Clearance F Appendix F to Part 512 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION CONFIDENTIAL BUSINESS INFORMATION Pt. 512, App. F Appendix F to...

  12. 50 CFR 14.52 - Clearance of imported wildlife.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 50 Wildlife and Fisheries 1 2013-10-01 2013-10-01 false Clearance of imported wildlife. 14.52 Section 14.52 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR TAKING, POSSESSION, TRANSPORTATION, SALE, PURCHASE, BARTER, EXPORTATION, AND IMPORTATION OF WILDLIFE...

  13. 50 CFR 14.52 - Clearance of imported wildlife.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 50 Wildlife and Fisheries 1 2012-10-01 2012-10-01 false Clearance of imported wildlife. 14.52 Section 14.52 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR TAKING, POSSESSION, TRANSPORTATION, SALE, PURCHASE, BARTER, EXPORTATION, AND IMPORTATION OF WILDLIFE...

  14. 50 CFR 14.52 - Clearance of imported wildlife.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 50 Wildlife and Fisheries 1 2011-10-01 2011-10-01 false Clearance of imported wildlife. 14.52 Section 14.52 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR TAKING, POSSESSION, TRANSPORTATION, SALE, PURCHASE, BARTER, EXPORTATION, AND IMPORTATION OF WILDLIFE...

  15. 50 CFR 14.52 - Clearance of imported wildlife.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 50 Wildlife and Fisheries 1 2014-10-01 2014-10-01 false Clearance of imported wildlife. 14.52 Section 14.52 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR TAKING, POSSESSION, TRANSPORTATION, SALE, PURCHASE, BARTER, EXPORTATION, AND IMPORTATION OF WILDLIFE...

  16. 14 CFR 27.411 - Ground clearance: tail rotor guard.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Ground clearance: tail rotor guard. 27.411 Section 27.411 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Strength Requirements Control Surface...

  17. Harmonic Measure of Critical Curves

    SciTech Connect

    Bettelheim, E.; Rushkin, I.; Gruzberg, I.A.; Wiegmann, P.

    2005-10-21

    Fractal geometry of critical curves appearing in 2D critical systems is characterized by their harmonic measure. For systems described by conformal field theories with central charge c{<=}1, scaling exponents of the harmonic measure have been computed by Duplantier [Phys. Rev. Lett. 84, 1363 (2000)] by relating the problem to boundary two-dimensional gravity. We present a simple argument connecting the harmonic measure of critical curves to operators obtained by fusion of primary fields and compute characteristics of the fractal geometry by means of regular methods of conformal field theory. The method is not limited to theories with c{<=}1.

  18. Active particles on curved surfaces

    NASA Astrophysics Data System (ADS)

    Fily, Yaouen; Baskaran, Aparna; Hagan, Michael

    Active systems have proved to be very sensitive to the geometry of their environment. This is often achieved by spending significant time at the boundary, probing its shape by gliding along it. I will discuss coarse graining the microscopic dynamics of self-propelled particles on a general curved surface to predict the way the density profile on the surface depends on its geometry. Beyond confined active particles, this formalism is a natural starting point to study objects that cannot leave the boundary at all, such as cells crawling on a curved substrate, animals running on uneven ground, or active colloids trapped at an interface.

  19. Shock detachment from curved wedges

    NASA Astrophysics Data System (ADS)

    Mölder, S.

    2017-03-01

    Curved shock theory is used to show that the flow behind attached shocks on doubly curved wedges can have either positive or negative post-shock pressure gradients depending on the freestream Mach number, the wedge angle and the two wedge curvatures. Given enough wedge length, the flow near the leading edge can choke to force the shock to detach from the wedge. This local choking can preempt both the maximum deflection and the sonic criteria for shock detachment. Analytical predictions for detachment by local choking are supported by CFD results.

  20. NEXT Performance Curve Analysis and Validation

    NASA Technical Reports Server (NTRS)

    Saripalli, Pratik; Cardiff, Eric; Englander, Jacob

    2016-01-01

    Performance curves of the NEXT thruster are highly important in determining the thruster's ability in performing towards mission-specific goals. New performance curves are proposed and examined here. The Evolutionary Mission Trajectory Generator (EMTG) is used to verify variations in mission solutions based on both available thruster curves and the new curves generated. Furthermore, variations in BOL and EOL curves are also examined. Mission design results shown here validate the use of EMTG and the new performance curves.

  1. Metabolism of nanomaterials in vivo: blood circulation and organ clearance.

    PubMed

    Wang, Bing; He, Xiao; Zhang, Zhiyong; Zhao, Yuliang; Feng, Weiyue

    2013-03-19

    Before researchers apply nanomaterials (NMs) in biomedicine, they need to understand the blood circulation and clearance profile of these materials in vivo. These qualities determine the balance between nanomaterial-induced activity and unwanted toxicity. NMs have heterogeneous characteristics: they combine the bulk properties of solids with the mobility of molecules, and their highly active contact interfaces exhibit diverse functionalities. Any new and unexpected circulation features and clearance patterns are of great concern in toxicological studies and pharmaceutical screens. A number of studies have reported that NMs can enter the bloodstream directly during their application or indirectly via inhalation, ingestion, and dermal exposure. Due to the small size of NMs, the blood can then transport them throughout the circulation and to many organs where they can be stored. In this Account, we discuss the blood circulation and organ clearance patterns of NMs in the lung, liver, and kidney. The circulation of NMs in bloodstream is critical for delivery of inhalable NMs to extrapulmonary organs, the delivery of injectable NMs, the dynamics of tissue redistribution, and the overall targeting of drug carriers to specific cells and organs. The lung, liver, and kidney are the major distribution sites and target organs for NMs exposure, and the clearance patterns of NMs in these organs are critical for understanding the in vivo fate of NMs. Current studies suggest that multiple factors control the circulation and organ clearance of NMs. The size, shape, surface charge, surface functional groups, and aspect ratio of NMs as well as tissue microstructures strongly influence the circulation of NMs in bloodstream, their site-specific extravasation, and their clearance profiles within organs. Therefore structure design and surface modification can improve biocompatibility, regulate the in vivo metabolism, and reduce the toxicity of NMs. The biophysicochemical interactions

  2. Parasite Clearance and Artemether Pharmacokinetics Parameters Over the Course of Artemether-Lumefantrine Treatment for Malaria in Human Immunodeficiency Virus (HIV)-Infected and HIV-Uninfected Ugandan Children

    PubMed Central

    Kajubi, Richard; Huang, Liusheng; Were, Moses; Kiconco, Sylvia; Li, Fangyong; Marzan, Florence; Gingrich, David; Nyunt, Myaing M.; Ssebuliba, Joshua; Mwebaza, Norah; Aweeka, Francesca T.

    2016-01-01

    Background. Artemisinins are primarily responsible for initial parasite clearance. Antimalarial pharmacokinetics (PK), human immunodeficiency virus (HIV) infection, and antiretroviral therapy have been shown to impact treatment outcomes, although their impact on early parasite clearance in children has not been well characterized. Methods. Parasite clearance parameters were generated from twice-daily blood smears in HIV-infected and HIV-uninfected Ugandan children treated with artemether-lumefantrine (AL). Artemether and dihydroartemisinin (DHA) area-under-the-curve from 0–8 hours (AUC0-8hr) after the 1st AL dose was compared with AUC0-8hr after the last (6th) dose in a concurrently enrolled cohort. The association between post-1st dose artemisinin AUC0-8hr and parasite clearance was assessed. Results. Parasite clearance was longer in HIV-infected versus HIV-uninfected children (median, 3.5 vs 2.8 hours; P = .003). Artemether AUC0-8hr was 3- to 4-fold lower after the 6th dose versus the 1st dose of AL in HIV-infected children on nevirapine- or lopinavir/ritionavir-based regimens and in HIV-uninfected children (P ≤ .002, 1st vs 6th-dose comparisons). Children on efavirenz exhibited combined post-1st dose artemether/DHA exposure that was significantly lower than those on lopinavir/ritonavir and HIV-uninfected children. Multiple regression analysis supported that the effect of artemether/DHA exposure on parasite clearance was significantly moderated by HIV status. Conclusions. Parasite clearance rates remain rapid in Uganda and were not found to associate with PK exposure. However, significant decreases in artemisinin PK with repeated dosing in nearly all children, coupled with small, but significant increase in parasite clearance half-life in those with HIV, may have important implications for AL efficacy, particularly because reports of artemisinin resistance are increasing. PMID:28018925

  3. 77 FR 43373 - Emergency Clearance; Public Information Collection Requirements Submitted to the Office of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-07-24

    ... From the Federal Register Online via the Government Publishing Office NATIONAL SCIENCE FOUNDATION... Budget; Notice AGENCY: National Science Foundation. ACTION: Emergency Clearance: Public Information... addressed to Suzanne Plimpton, Reports Clearance Officer, National Science Foundation, 4201 Wilson Blvd.,...

  4. 78 FR 56222 - Agency Information Collection Activities; Comment Request; Highly Qualified Teachers Clearance

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-12

    ... Agency Information Collection Activities; Comment Request; Highly Qualified Teachers Clearance AGENCY... notice will be considered public records. Title of Collection: Highly Qualified Teachers Clearance OMB... disadvantaged students) are taught by teachers participating in an alternative route to certification...

  5. 78 FR 67344 - Highly Qualified Teachers Clearance; Extension of Public Comment Period; Correction

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-11-12

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF EDUCATION Highly Qualified Teachers Clearance; Extension of Public Comment Period; Correction AGENCY: Department of... comment for an information collection entitled, ``Highly Qualified Teachers Clearance,''...

  6. 19 CFR 122.66 - Clearance or permission to depart denied.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ...; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Clearance of Aircraft and Permission To Depart § 122.66 Clearance or permission to depart denied. If advance electronic air cargo information is not received...

  7. 77 FR 6128 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-02-07

    ... Collection; Comment Request; Generic Clearance for the Collection of Qualitative Feedback on Agency Service... Nursing Research (NINR), National Institutes of Health (NIH), has submitted a Generic Information Collection Request (Generic ICR): ``Generic Clearance for the Collection of Qualitative Feedback on...

  8. 78 FR 72153 - Proposed Collection; Comment Request for Generic Clearance for the Collection of Qualitative...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-12-02

    ... Qualitative Feedback on Agency Service Delivery AGENCY: Internal Revenue Service (IRS), Treasury. ACTION..., the IRS is soliciting comments concerning Generic Clearance for the Collection of Qualitative Feedback... Clearance for the Collection of Qualitative Feedback on Agency Service Delivery. OMB Number:...

  9. 76 FR 74802 - Agency Information Collection Activities: Proposed Collection; Comment Request; Generic Clearance...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-01

    ... Collection; Comment Request; Generic Clearance for the Collection of Qualitative Feedback on Agency Service... ICR): ``Generic Clearance for the Collection of Qualitative Feedback on Agency Service Delivery '' to... policy for Extramural Research Administration, 6705 Rockledge Drive Suite 350, Bethesda, MD...

  10. 76 FR 49838 - Proposed Collection; Comment Request for Generic Clearance for the Collection of Qualitative...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-11

    ... Qualitative Feedback on Agency Service Delivery AGENCY: Internal Revenue Service (IRS), Treasury. ACTION..., the IRS is soliciting comments concerning Generic Clearance for the Collection of Qualitative Feedback... INFORMATION: Title: Generic Clearance for the Collection of Qualitative Feedback on Agency Service...

  11. Supply Curves of Conserved Energy

    SciTech Connect

    Meier, Alan Kevin

    1982-05-01

    Supply curves of conserved energy provide an accounting framework that expresses the potential for energy conservation. The economic worthiness of a conservation measure is expressed in terms of the cost of conserved energy, and a measure is considered economical when the cost of conserved energy is less than the price of the energy it replaces. A supply curve of conserved energy is independent of energy prices; however, the economical reserves of conserved energy will depend on energy prices. Double-counting of energy savings and error propagation are common problems when estimating conservation potentials, but supply curves minimize these difficulties and make their consequences predictable. The sensitivity of the cost of conserved energy is examined, as are variations in the optimal investment strategy in response to changes in inputs. Guidelines are presented for predicting the consequences of such changes. The conservation supply curve concept can be applied to peak power, water, pollution, and other markets where consumers demand a service rather than a particular good.

  12. Interpolation and Polynomial Curve Fitting

    ERIC Educational Resources Information Center

    Yang, Yajun; Gordon, Sheldon P.

    2014-01-01

    Two points determine a line. Three noncollinear points determine a quadratic function. Four points that do not lie on a lower-degree polynomial curve determine a cubic function. In general, n + 1 points uniquely determine a polynomial of degree n, presuming that they do not fall onto a polynomial of lower degree. The process of finding such a…

  13. Variability among polysulphone calibration curves

    NASA Astrophysics Data System (ADS)

    Casale, G. R.; Borra, M.; Colosimo, A.; Colucci, M.; Militello, A.; Siani, A. M.; Sisto, R.

    2006-09-01

    Within an epidemiological study regarding the correlation between skin pathologies and personal ultraviolet (UV) exposure due to solar radiation, 14 field campaigns using polysulphone (PS) dosemeters were carried out at three different Italian sites (urban, semi-rural and rural) in every season of the year. A polysulphone calibration curve for each field experiment was obtained by measuring the ambient UV dose under almost clear sky conditions and the corresponding change in the PS film absorbance, prior and post exposure. Ambient UV doses were measured by well-calibrated broad-band radiometers and by electronic dosemeters. The dose-response relation was represented by the typical best fit to a third-degree polynomial and it was parameterized by a coefficient multiplying a cubic polynomial function. It was observed that the fit curves differed from each other in the coefficient only. It was assessed that the multiplying coefficient was affected by the solar UV spectrum at the Earth's surface whilst the polynomial factor depended on the photoinduced reaction of the polysulphone film. The mismatch between the polysulphone spectral curve and the CIE erythemal action spectrum was responsible for the variability among polysulphone calibration curves. The variability of the coefficient was related to the total ozone amount and the solar zenith angle. A mathematical explanation of such a parameterization was also discussed.

  14. Breakpoint chlorination curves of greywater.

    PubMed

    March, J G; Gual, M

    2007-08-01

    A study on chlorination of raw greywater with hypochlorite is reported in this paper. Samples were chlorinated in a variety of conditions, and residual chlorine (Cl2) was measured spectrophotometrically. For each sample, the chlorination curve (chlorine residuals versus chlorine dose) was obtained. Curves showed the typical hump-and-dip profile attributable to the formation and destruction of chloramines. It was observed that, after reactions with strong reductants and chloramines-forming compounds, the remaining organic matter exerted a certain demand of chlorine. The evolution of chlorination curves with addition of ammonia and dodecylbencene sulfonate sodium salt and with dilution of the greywater sample were studied. In addition, chlorination curves at several contact times have been obtained, resulting in slower chlorine decay in the hump zone than in the dip zone. In addition, the decay of coliforms in chlorinated samples was also investigated. It was found that, for a chlorination dosage corresponding to the maximum of the hump zone (average 8.9 mg Cl2/ L), samples were negative in coliforms after 10 to 30 minutes of contact time. After-growth was not observed within 3 days after chlorination. Implications in chlorination treatments of raw greywater can be derived from these results.

  15. 76 FR 54777 - Center for Devices and Radiological Health 510(k) Clearance Process; Recommendations Proposed in...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-09-02

    ... HUMAN SERVICES Food and Drug Administration Center for Devices and Radiological Health 510(k) Clearance... Health, The FDA 510(k) Clearance Process at 35 Years''; Public Meeting; Correction AGENCY: Food and Drug... Devices and the Public's Health, The FDA 510(k) Clearance Process at 35 Years.' '' The document...

  16. 49 CFR 236.22 - Semaphore signal arm; clearance to other objects.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Semaphore signal arm; clearance to other objects... Rules and Instructions: All Systems Roadway Signals and Cab Signals § 236.22 Semaphore signal arm; clearance to other objects. At least one-half inch clearance shall be provided between semaphore signal...

  17. 49 CFR 236.22 - Semaphore signal arm; clearance to other objects.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Semaphore signal arm; clearance to other objects... Rules and Instructions: All Systems Roadway Signals and Cab Signals § 236.22 Semaphore signal arm; clearance to other objects. At least one-half inch clearance shall be provided between semaphore signal...

  18. 49 CFR 236.22 - Semaphore signal arm; clearance to other objects.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Semaphore signal arm; clearance to other objects... Rules and Instructions: All Systems Roadway Signals and Cab Signals § 236.22 Semaphore signal arm; clearance to other objects. At least one-half inch clearance shall be provided between semaphore signal...

  19. 49 CFR 236.22 - Semaphore signal arm; clearance to other objects.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Semaphore signal arm; clearance to other objects... Rules and Instructions: All Systems Roadway Signals and Cab Signals § 236.22 Semaphore signal arm; clearance to other objects. At least one-half inch clearance shall be provided between semaphore signal...

  20. 49 CFR 236.22 - Semaphore signal arm; clearance to other objects.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Semaphore signal arm; clearance to other objects... Rules and Instructions: All Systems Roadway Signals and Cab Signals § 236.22 Semaphore signal arm; clearance to other objects. At least one-half inch clearance shall be provided between semaphore signal...

  1. Wide Area Recovery and Resiliency Program (WARRP) Interim Clearance Strategy for Environments Contaminated with Cesium-137

    DTIC Science & Technology

    2012-07-01

    Wide Area Recovery & Resiliency Program (WARRP) Interim Clearance Strategy for Environments Contaminated with Cesium -137 July...and Resiliency Program (WARRP) Interim Clearance Strategy for Environments Contaminated with Cesium -137 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c...speedy recovery. 15. SUBJECT TERMS WARRP, Cesium -137, Clearance Strategy, Remediation 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT

  2. 75 FR 370 - Emergency Clearance: Public Information Collection Requirements Submitted to the Office of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-05

    ... [Document Identifier: CMS-10310] Emergency Clearance: Public Information Collection Requirements Submitted... reasonably comply with the normal clearance procedures due to an unexpected event as stated in 5 CFR 1320.13... processed under the emergency clearance process. Approval of this package is essential in order to...

  3. 77 FR 14807 - Emergency Clearance: Public Information Collection Requirements Submitted to the Office of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-13

    ... HUMAN SERVICES Centers for Medicare and Medicaid Services Emergency Clearance: Public Information... section 1862(a)(1)(A) of the Social Security Act. We cannot reasonably comply with the normal clearance procedures in that public harm is reasonably likely to result if normal clearance procedures are followed...

  4. 76 FR 39114 - Agency Information Collection Activities: Vessel Entrance or Clearance Statement

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-07-05

    ... Clearance Statement AGENCY: U.S. Customs and Border Protection (CBP), Department of Homeland Security... concerning the Vessel Entrance or Clearance Statement (CBP Form 1300). This request for comment is being made... or Clearance Statement. OMB Number: 1651-0019. Form Number: CBP Form 1300. Abstract: CBP Form...

  5. 78 FR 5858 - Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-28

    ... Federal Aviation Administration Agency Information Collection Activities: Requests for Comments; Clearance.../or include your comments in the request for OMB's clearance of this information collection. Issued in Washington, DC, on January 22, 2013. Albert R. Spence, FAA Assistant Information Collection Clearance...

  6. 10 CFR 95.20 - Grant, denial or termination of facility clearance.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Grant, denial or termination of facility clearance. 95.20 Section 95.20 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) FACILITY SECURITY CLEARANCE AND... termination of facility clearance. The Division of Security Operations shall provide notification in...

  7. 78 FR 51729 - Emergency Clearance: Public Information Collection Requirements Submitted to the Office of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-21

    ... Clearance: Public Information Collection Requirements Submitted to the Office of Management and Budget (OMB... CFR Part 1320(a)(2)(i) because public harm is reasonably likely to result if the normal clearance... call the Reports Clearance Office on (410) 786-1326. In commenting on the proposed...

  8. 76 FR 63302 - Emergency Clearance: Public Information Collection Requirements Submitted to the Office of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-10-12

    ... Services [Document Identifier CMS-10379] Emergency Clearance: Public Information Collection Requirements... comply with the normal clearance procedures in that public harm is reasonably likely to result if normal clearance procedures are followed as stated in 5 CFR 1320.13(a)(2)(i). The approval of this data...

  9. 76 FR 53530 - Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-08-26

    ... Federal Aviation Administration Agency Information Collection Activities: Requests for Comments; Clearance.../or include your comments in the request for OMB's clearance of this information collection. Issued in Washington, DC, on August 19, 2011. Carla Scott, FAA Information Collection Clearance Officer, IT...

  10. 76 FR 76737 - Emergency Clearance: Public Information Collection Requirements Submitted to the Office of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-08

    ... [Document Identifier CMS-10417] Emergency Clearance: Public Information Collection Requirements Submitted to... section 1862(a)(1)(A) of the Social Security Act. We cannot reasonably comply with the normal clearance procedures in that public harm is reasonably likely to result if normal clearance procedures are followed...

  11. 76 FR 59711 - Agency Information Collection Activities; Vessel Entrance or Clearance Statement

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-09-27

    ... Clearance Statement AGENCY: U.S. Customs and Border Protection, Department of Homeland Security. ACTION: 30... review and approval in accordance with the Paperwork Reduction Act: Vessel Entrance or Clearance... Clearance Statement. OMB Number: 1651-0019. Form Number: CBP Form 1300. Abstract: CBP Form 1300,...

  12. 76 FR 19777 - Emergency Clearance: Public Information Collection Requirements Submitted to the Office of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-08

    ... HUMAN SERVICES Centers for Medicare & Medicaid Services Emergency Clearance: Public Information... cannot reasonably comply with the normal clearance procedures due to an unexpected event as stated in 5 CFR 1320.13(a)(2)(iii). The use of the normal clearance procedures would cause a statutory deadline...

  13. 19 CFR 4.95 - Records of entry and clearance of vessels.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Records of entry and clearance of vessels. 4.95... clearance of vessels. Permanent records shall be prepared at each customhouse of all entries of vessels on Customs Form 1400 and of all clearances and permits to proceed on Customs Form 1401. Whenever a vessel...

  14. 14 CFR 91.173 - ATC clearance and flight plan required.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false ATC clearance and flight plan required. 91... Instrument Flight Rules § 91.173 ATC clearance and flight plan required. No person may operate an aircraft in... appropriate ATC clearance....

  15. 33 CFR 402.8 - Post-clearance date operational surcharges.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Post-clearance date operational..., DEPARTMENT OF TRANSPORTATION TARIFF OF TOLLS § 402.8 Post-clearance date operational surcharges. (a) Subject... place set out in column 1 of § 402.11 within a period after the clearance date established by...

  16. 76 FR 56214 - 60-Day Notice of Intention To Request Clearance for Information Collection: Opportunity for...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-09-12

    ... Office of the Secretary 60-Day Notice of Intention To Request Clearance for Information Collection... on an intended request for clearance of information collection. DATES: Public comments will be... collection clearance. Description of Need: The Office of Youth in the Great Outdoors needs information...

  17. 32 CFR 644.341 - Clearance with the Armed Services committees.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true Clearance with the Armed Services committees. 644... (CONTINUED) REAL PROPERTY REAL ESTATE HANDBOOK Disposal Clearances-Army Military Real Property § 644.341 Clearance with the Armed Services committees. (a) Prior to a final report of excess, or transfer to...

  18. 78 FR 21118 - Agency Information Collection Activities; Comment Request; Streamlined Clearance Process for...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-09

    ... Agency Information Collection Activities; Comment Request; Streamlined Clearance Process for... Clearance Division, U.S. Department of Education, 400 Maryland Avenue SW., LBJ, Room 2E105, Washington, DC... Clearance Process for Discretionary Grants OMB Control Number: 1894-0001 Type of Review: An extension of...

  19. 75 FR 39582 - Submission for OMB Review, Comment Request, Proposed Collection: General Clearance for Guidelines...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-07-09

    ... ARTS AND HUMANITIES Submission for OMB Review, Comment Request, Proposed Collection: General Clearance...: This notice proposes general clearance of the agency's guideline application and report forms. The 60-day Notice for the ``Notice of Continuance for General Clearance for Guidelines, Applications,...

  20. 48 CFR 245.7001-4 - DD Form 1640, Request for Plant Clearance.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false DD Form 1640, Request for Plant Clearance. 245.7001-4 Section 245.7001-4 Federal Acquisition Regulations System DEFENSE... Forms 245.7001-4 DD Form 1640, Request for Plant Clearance. Use to request plant clearance assistance...

  1. Comparison of Two Algebraic Methods for Curve/curve Intersection

    NASA Technical Reports Server (NTRS)

    Demontaudouin, Y.; Tiller, W.

    1985-01-01

    Most geometric modeling systems use either polynomial or rational functions to represent geometry. In such systems most computational problems can be formulated as systems of polynomials in one or more variables. Classical elimination theory can be used to solve such systems. Here Cayley's method of elimination is summarized and it is shown how it can best be used to solve the curve/curve intersection problem. Cayley's method was found to be a more straightforward approach. Furthermore, it is computationally simpler, since the elements of the Cayley matrix are one variable instead of two variable polynomials. Researchers implemented and tested both methods and found Cayley's to be more efficient. Six pairs of curves, representing mixtures of lines, circles, and cubic arcs were used. Several examples had multiple intersection points. For all six cases Cayley's required less CPU time than the other method. The average time ratio of method 1 to method 2 was 3.13:1, the least difference was 2.33:1, and the most dramatic was 6.25:1. Both of the above methods can be extended to solve the surface/surface intersection problem.

  2. Growth hormone secretion and clearance rates in growing beef steers implanted with estrogenic anabolic compounds.

    PubMed

    Gopinath, R; Kitts, W D

    1984-01-01

    The effect of estrogenic anabolic compounds on the kinetic parameters of metabolism of growth hormone (GH) was studied in growing beef steers. Twenty-four beef steers were randomly placed into four groups and assigned to one of the following four treatment groups: zeranol, diethylstilbestrol (DES), Synovex-S and an unimplanted control. GH metabolism was studied from eight steers on day 20 following the implantation of anabolic compounds. The animals were rapidly injected with a solution of bGH (NIH-GH-B18) and the disappearance of injected GH from the plasma was monitored up to 120 min following the injection. The plasma GH disappearance curve displayed an initial rapid phase lasting 5 min and a slow disappearance phase lasting 42 min; the fractional turnover rate from the two compartments were 0.167 and 0.017 min-1, respectively. The average volume of distribution of GH in steers was 6% of the body weight. Mean values of metabolic clearance and secretion rates of GH in steers were 21 liters/h and 252 micrograms/h or 74.5 ml/kg/h and 0.91 microgram/kg/h, respectively. Steers implanted with anabolic compounds gained more rapidly (P less than 0.05) than the controls. Plasma basal GH concentration appeared to be higher in all the implanted than in the control steers. The secretion rate of GH was increased (P less than 0.05) in steers implanted with anabolic compounds when compared to control steers. The secretion rate (microgram/kg/h) was about 96% (P less than 0.05), 107% (P less than 0.05) and 81% (P less than 0.05) higher in steers implanted with DES, zeranol and Synovex-S, respectively, than in the control steers. All the compounds studied were equally effective in increasing the secretion of GH on day 20 following their implantation. Metabolic clearance rate of GH was not affected by anabolic compound implantation in steers. There was, however, a slight reduction in metabolic clearance rate due to DES and a slight elevation due to zeranol and Synovex-S when

  3. K2 Mission Light Curves

    NASA Astrophysics Data System (ADS)

    Smith, Jeffrey C.; morris, robert; Bryson, Steve; Jenkins, Jon Michael; Caldwell, Douglas

    2015-08-01

    The K2 mission is now generating light curves for its ecliptic-field campaigns. Producing good photometry for K2 is more challenging than for Kepler’s prime mission because periodic thruster firings are used to compensate for the loss of two reaction wheels. These firings, referred to as "roll tweaks", result in spacecraft rotation along the barrel axis and high corresponding image motion. The resulting motion-dominated systematic errors are dramatically different than the focus-dominated systematic errors experienced during the prime mission. They also make it challenging to properly identify and remove flux from background objects present in the optimal apertures. We summarize these challenges and describe the resulting modifications to the Kepler pipeline for the processing of K2 data. The quality of the K2 mission light curves is characterized.

  4. Infinite swapping in curved spaces

    NASA Astrophysics Data System (ADS)

    Curotto, E.; Mella, Massimo

    2014-01-01

    We develop an extension of the infinite swapping and partial infinite swapping techniques [N. Plattner, J. D. Doll, P. Dupuis, H. Wang, Y. Liu, and J. E. Gubernatis, J. Chem. Phys. 135, 134111 (2011)] to curved spaces. Furthermore, we test the performance of infinite swapping and partial infinite swapping in a series of flat spaces characterized by the same potential energy surface model. We develop a second order variational algorithm for general curved spaces without the extended Lagrangian formalism to include holonomic constraints. We test the new methods by carrying out NVT classical ensemble simulations on a set of multidimensional toroids mapped by stereographic projections and characterized by a potential energy surface built from a linear combination of decoupled double wells shaped purposely to create rare events over a range of temperatures.

  5. Infinite swapping in curved spaces.

    PubMed

    Curotto, E; Mella, Massimo

    2014-01-07

    We develop an extension of the infinite swapping and partial infinite swapping techniques [N. Plattner, J. D. Doll, P. Dupuis, H. Wang, Y. Liu, and J. E. Gubernatis, J. Chem. Phys. 135, 134111 (2011)] to curved spaces. Furthermore, we test the performance of infinite swapping and partial infinite swapping in a series of flat spaces characterized by the same potential energy surface model. We develop a second order variational algorithm for general curved spaces without the extended Lagrangian formalism to include holonomic constraints. We test the new methods by carrying out NVT classical ensemble simulations on a set of multidimensional toroids mapped by stereographic projections and characterized by a potential energy surface built from a linear combination of decoupled double wells shaped purposely to create rare events over a range of temperatures.

  6. Analysis of Exoplanet Light Curves

    NASA Astrophysics Data System (ADS)

    Erdem, A.; Budding, E.; Rhodes, M. D.; Püsküllü, Ç.; Soydugan, F.; Soydugan, E.; Tüysüz, M.; Demircan, O.

    2015-07-01

    We have applied the close binary system analysis package WINFITTER to a variety of exoplanet transiting light curves taken both from the NASA Exoplanet Archive and our own ground-based observations. WINFitter has parameter options for a realistic physical model, including gravity brightening and structural parameters derived from Kopal's applications of the relevant Radau equation, and it includes appropriate tests for determinacy and adequacy of its best fitting parameter sets. We discuss a number of issues related to empirical checking of models for stellar limb darkening, surface maculation, Doppler beaming, microvariability, and transit time variation (TTV) effects. The Radau coefficients used in the light curve modeling, in principle, allow structural models of the component stars to be tested.

  7. Accelerating Around an Unbanked Curve

    NASA Astrophysics Data System (ADS)

    Mungan, Carl E.

    2006-02-01

    The December 2004 issue of TPT presented a problem concerning how a car should accelerate around an unbanked curve of constant radius r starting from rest if it is to avoid skidding. Interestingly enough, two solutions were proffered by readers.2 The purpose of this note is to compare and contrast the two approaches. Further experimental investigation of various turning strategies using a remote-controlled car and overhead video analysis could make for an interesting student project.

  8. Standardized protocols for plasma clearance of iohexol are not appropriate for determination of glomerular filtration rates in anesthetized California sea lions (Zalophus californianus).

    PubMed

    Dennison, Sophie E; Gulland, Frances M D; Braselton, W Emmett

    2010-03-01

    Abstract: Plasma clearance of iohexol was evaluated in eight anesthetized California sea lions (Zalophus californianus), without evidence of renal dysfunction, to determine if the one-compartment model and the sample protocol used in dogs and cats could be applied to this species. Nonlinearity between samples in 75% (6/8) of sea lions voided those results. An additional two anesthetized sea lions were sampled at 5, 30, 45, 60, 120, 180, 240, and 360 min post iohexol injection and semi-logarithmic curves calculated. Plasma iohexol clearance values calculated by one-, two-, and noncompartment models were in poor agreement, suggesting that the standardized protocol described for dogs and cats cannot simply be applied to California sea lions, probably due to the effects of the dive reflex induced during anesthesia.

  9. Gas film lubrication equations for very small clearances

    SciTech Connect

    Sobehart, J.R.; Reyna, L.G.

    1994-05-01

    In the hard disk magnetic recording technology, the slider carrying the magnetic elements is supported above the magnetic disk by a self-acting air bearing, which produces the load support. A lubricating film must support a required load with suitably small frictional energy losses and without introducing undesirable instabilities. Under submicron clearance conditions, gas film flow can not be described with continuum models since the molecular mean free path is not negligible compared with the clearance. Accurate results for the load-carrying capacity of gas films for arbitrary Knudsen number are very important since they strongly influence the design of the flying head slider and, consequently, the performance of the magnetic disk storage unit. Here we generalize the previous lubrication equations for arbitrary Knudsen number, accommodation coefficient and a small inclination of the slider relative to the magnetic disk surface.

  10. Impaired tracheobronchial clearance in patients with mild stable asthma.

    PubMed Central

    Bateman, J R; Pavia, D; Sheahan, N F; Agnew, J E; Clarke, S W

    1983-01-01

    Tracheobronchial mucociliary clearance was measured with the radioaerosol technique in 25 patients with stable, mild asthma, none of whom was taking systemic corticosteroids. The results were compared with those obtained from a control group of 25 healthy subjects matched for age and sex. All patients and healthy subjects were non-smokers. Ventilatory function was significantly impaired in the asthmatic group, which resulted in a more central initial tracheobronchial deposition of inhaled radioaerosol than in the control group. Despite the shorter transit path along the ciliated airways for the tracer radioaerosol in the asthmatic group, mucociliary clearance was found to be significantly poorer than in the healthy control group. This may be important with respect to bronchial mucus plugging. PMID:6879499

  11. Nonlinear dynamic characteristic analysis of jointed beam with clearance

    NASA Astrophysics Data System (ADS)

    Zhang, Jing; Guo, Hong-Wei; Liu, Rong-Qiang; Wu, Juan; Kou, Zi-Ming; Deng, Zong-Quan

    2016-12-01

    The impact and elasticity of discontinuous beams with clearance frequently affect the dynamic response of structures used in space missions. This study investigates the dynamic response of jointed beams which are the periodic units of deployable structures. The vibration process of jointed beams includes free-play and impact stages. A method for the dynamic analysis of jointed beams with clearance is proposed based on mode superposition and instantaneous static deformation. Transfer matrix, which expresses the relationship of the responses before and after the impact of jointed beams, is derived to calculate the response of the jointed beams after a critical position. The dynamic responses of jointed beams are then simulated. The effects of various parameters on the displacement and velocity of beams are investigated.

  12. Schwann cell autophagy, myelinophagy, initiates myelin clearance from injured nerves

    PubMed Central

    Gomez-Sanchez, Jose A.; Carty, Lucy; Iruarrizaga-Lejarreta, Marta; Palomo-Irigoyen, Marta; Varela-Rey, Marta; Griffith, Megan; Hantke, Janina; Macias-Camara, Nuria; Azkargorta, Mikel; Aurrekoetxea, Igor; De Juan, Virginia Gutiérrez; Jefferies, Harold B.J.; Aspichueta, Patricia; Elortza, Félix; Aransay, Ana M.; Martínez-Chantar, María L.; Baas, Frank; Mato, José M.; Mirsky, Rhona

    2015-01-01

    Although Schwann cell myelin breakdown is the universal outcome of a remarkably wide range of conditions that cause disease or injury to peripheral nerves, the cellular and molecular mechanisms that make Schwann cell–mediated myelin digestion possible have not been established. We report that Schwann cells degrade myelin after injury by a novel form of selective autophagy, myelinophagy. Autophagy was up-regulated by myelinating Schwann cells after nerve injury, myelin debris was present in autophagosomes, and pharmacological and genetic inhibition of autophagy impaired myelin clearance. Myelinophagy was positively regulated by the Schwann cell JNK/c-Jun pathway, a central regulator of the Schwann cell reprogramming induced by nerve injury. We also present evidence that myelinophagy is defective in the injured central nervous system. These results reveal an important role for inductive autophagy during Wallerian degeneration, and point to potential mechanistic targets for accelerating myelin clearance and improving demyelinating disease. PMID:26150392

  13. Apoptotic cell clearance: basic biology and therapeutic potential

    PubMed Central

    Poon, Ivan K. H.; Lucas, Christopher D.

    2014-01-01

    Prompt removal of apoptotic cells by phagocytes is important for maintaining tissue homeostasis. The molecular and cellular events that underpin apoptotic cell recognition and uptake, and the subsequent biological responses are increasingly better defined. The detection and disposal of apoptotic cells generally promote an anti-inflammatory response at the tissue level, as well as immunological tolerance. Consequently, defects in apoptotic cell clearance have been linked with a variety of inflammatory diseases and autoimmunity. Conversely, under certain conditions such as killing tumour cells by specific cell death inducers, the recognition of apoptotic tumour cells can promote an immunogenic response and anti-tumour immunity. Here, we review the current understanding of the complex process of apoptotic cell clearance in physiology and pathology, and discuss how this knowledge could be harnessed for new therapeutic strategies. PMID:24481336

  14. Lactate and lactate clearance in acute cardiac care patients

    PubMed Central

    Lazzeri, Chiara; Picariello, Claudio; Dini, Carlotta Sorini; Gensini, Gian Franco; Valente, Serafina

    2012-01-01

    Hyperlactataemia is commonly used as a diagnostic and prognostic tool in intensive care settings. Recent studies documented that serial lactate measurements over time (or lactate clearance), may be clinically more reliable than lactate absolute value for risk stratification in different pathological conditions. While the negative prognostic role of hyperlactataemia in several critical ill diseases (such as sepsis and trauma) is well established, data in patients with acute cardiac conditions (i.e. acute coronary syndromes) are scarce and controversial. The present paper provides an overview of the current available evidence on the clinical role of lactic acid levels and lactate clearance in acute cardiac settings (acute coronary syndromes, cardiogenic shock, cardiac surgery), focusing on its prognostic role. PMID:24062898

  15. Microwave Sensor for Blade Tip Clearance and Structural Health Measurements

    NASA Technical Reports Server (NTRS)

    Woike, Mark R.; Bencic, Timothy J.

    2008-01-01

    The use of microwave based sensors for the health monitoring of rotating machinery is being explored at the NASA Glenn Research Center. The microwave sensor works on the principle of sending a continuous signal towards a rotating component and measuring the reflected signal. The phase shift of the reflected signal is proportional to the distance between the sensor and the component that is being measured. This type of sensor is beneficial in that it has the ability to operate at extremely high temperatures and is unaffected by contaminants that may be present in the rotating machinery. It is intended to use these probes in the hot sections of turbine engines for closed loop turbine clearance control and structural health measurements. Background on the sensors, an overview of their calibration and preliminary results from using them to make blade tip clearance and health measurements on a large axial vane fan will be presented.

  16. Lung-clearance mechanisms following inhalation of acid sulfates

    SciTech Connect

    Wolff, R.K.; Muggenburg, B.A.; Silbaugh, S.A.; Carpenter, R.L.; Rowatt, J.D.; Hill, J.O.

    1982-08-01

    These studies have indicated that acute exposures (1-6 hrs) to sulfuric acid at levels of 0.5 to 1.0 mg/m/sup 3/ can produce impairments in mucous clearance. The impairments can last for up to a week following a 1 hr exposure. These effects and studies by others suggest that high sulfate levels in polluted conditions may be one factor in observed increases of hospital visits for respiratory problems. Long term exposures to elevated levels of sulfates resulting in decreases of clearance could also be an initiating factor in producing chronic obstructive pulmonary disease (COPD). These studies have also shown that it is the larger size fraction (0.6 to 1.0 ..mu..m) of sulfuric acid mist in the urban aerosol which is predominantly responsible for at least the acute effects.

  17. Insulin clearance is different in men and women

    PubMed Central

    Jensen, Michael D.; Nielsen, Soren; Gupta, Nidhi; Basu, Rita; Rizza, Robert

    2011-01-01

    Objective Insulin is often infused based upon total body weight (TBW) or fat free mass (FFM)for glucose clamp protocols. We observed greater insulin concentrations in men than women using this approach and examined whether splanchnic insulin extraction accounts for the differences. Materials/Methods Whole body insulin clearance was measured during a pancreatic clamp study (somatostatin to inhibit islet hormone secretion) including 13 adults (6 men) and whole body insulin clearance was measured during a euglycemic, hyperinsulinemic clamp study including 27 adults (13 men). Femoral artery and hepatic vein blood samples were collected to measure splanchnic insulin balance. For the pancreatic clamp study insulin was infused at rates of 0.5, 1.0, and 2.0 mU•kgTBW−1•min−1 and for the euglycemic, hyperinsulinemic clamp study insulin was infused at 2.5 mU•kg FFM−1•min−1. Results Significantly greater arterial insulin concentrations were found in men than women. Splanchnic plasma flow was similar in men and women in both protocols. Splanchnic insulin extraction and the fraction of infused insulin removed by splanchnic bed were significantly greater in men than in women. However, whole body insulin clearance was greater in women than men. Conclusions Infusing insulin per body weight or FFM results in higher plasma insulin concentrations in men than women. Splanchnic insulin extraction is greater in men, indicating greater peripheral insulin clearance in women accounts for the sex differences we observed. This finding has implications for insulin clamp study design and raises the question of which tissues take up more insulin in women. PMID:22000585

  18. Numerical investigation of tip clearance cavitation in Kaplan runners

    NASA Astrophysics Data System (ADS)

    Nikiforova, K.; Semenov, G.; Kuznetsov, I.; Spiridonov, E.

    2016-11-01

    There is a gap between the Kaplan runner blade and the shroud that makes for a special kind of cavitation: cavitation in the tip leakage flow. Two types of cavitation caused by the presence of clearance gap are known: tip vortex cavitation that appears at the core of the rolled up vortex on the blade suction side and tip clearance cavitation that appears precisely in the gap between the blade tip edge and the shroud. In the context of this work numerical investigation of the model Kaplan runner has been performed taking into account variable tip clearance for several cavitation regimes. The focus is put on investigation of structure and origination of mechanism of cavitation in the tip leakage flow. Calculations have been performed with the help of 3-D unsteady numerical model for two-phase medium. Modeling of turbulent flow in this work has been carried out using full equations of Navier-Stokes averaged by Reynolds with correction for streamline curvature and system rotation. For description of this medium (liquid-vapor) simplification of Euler approach is used; it is based on the model of interpenetrating continuums, within the bounds of this two- phase medium considered as a quasi-homogeneous mixture with the common velocity field and continuous distribution of density for both phases. As a result, engineering techniques for calculation of cavitation conditioned by existence of tip clearance in model turbine runner have been developed. The detailed visualization of the flow was carried out and vortex structure on the suction side of the blade was reproduced. The range of frequency with maximum value of pulsation was assigned and maximum energy frequency was defined; it is based on spectral analysis of the obtained data. Comparison between numerical computation results and experimental data has been also performed. The location of cavitation zone has a good agreement with experiment for all analyzed regimes.

  19. Macrophage migration inhibitory factor promotes clearance of pneumococcal colonization.

    PubMed

    Das, Rituparna; LaRose, Meredith I; Hergott, Christopher B; Leng, Lin; Bucala, Richard; Weiser, Jeffrey N

    2014-07-15

    Human genetic polymorphisms associated with decreased expression of macrophage migration inhibitory factor (MIF) have been linked to the risk of community-acquired pneumonia. Because Streptococcus pneumoniae is the leading cause of community-acquired pneumonia and nasal carriage is a precursor to invasive disease, we explored the role of MIF in the clearance of pneumococcal colonization in a mouse model. MIF-deficient mice (Mif(-/-)) showed prolonged colonization with both avirulent (23F) and virulent (6A) pneumococcal serotypes compared with wild-type animals. Pneumococcal carriage led to both local upregulation of MIF expression and systemic increase of the cytokine. Delayed clearance in the Mif(-/-) mice was correlated with reduced numbers of macrophages in upper respiratory tract lavages as well as impaired upregulation of MCP-1/CCL2. We found that primary human monocyte-derived macrophages as well as THP-1 macrophages produced MIF upon pneumococcal infection in a pneumolysin-dependent manner. Pneumolysin-induced MIF production required its pore-forming activity and phosphorylation of p38-MAPK in macrophages, with sustained p38-MAPK phosphorylation abrogated in the setting of MIF deficiency. Challenge with pneumolysin-deficient bacteria demonstrated reduced MIF upregulation, decreased numbers of macrophages in the nasopharynx, and less effective clearance. Mif(-/-) mice also showed reduced Ab response to pneumococcal colonization and impaired ability to clear secondary carriage. Finally, local administration of MIF was able to restore bacterial clearance and macrophage accumulation in Mif(-/-) mice. Our work suggests that MIF is important for innate and adaptive immunity to pneumococcal colonization and could be a contributing factor in genetic differences in pneumococcal disease susceptibility.

  20. Surface code—biophysical signals for apoptotic cell clearance

    NASA Astrophysics Data System (ADS)

    Biermann, Mona; Maueröder, Christian; Brauner, Jan M.; Chaurio, Ricardo; Janko, Christina; Herrmann, Martin; Muñoz, Luis E.

    2013-12-01

    Apoptotic cell death and the clearance of dying cells play an important and physiological role in embryonic development and normal tissue turnover. In contrast to necrosis, apoptosis proceeds in an anti-inflammatory manner. It is orchestrated by the timed release and/or exposure of so-called ‘find-me’, ‘eat me’ and ‘tolerate me’ signals. Mononuclear phagocytes are attracted by various ‘find-me’ signals, including proteins, nucleotides, and phospholipids released by the dying cell, whereas the involvement of granulocytes is prevented via ‘stay away’ signals. The exposure of anionic phospholipids like phosphatidylserine (PS) by apoptotic cells on the outer leaflet of the plasma membrane is one of the main ‘eat me’ signals. PS is recognized by a number of innate receptors as well as by soluble bridging molecules on the surface of phagocytes. Importantly, phagocytes are able to discriminate between viable and apoptotic cells both exposing PS. Due to cytoskeleton remodeling PS has a higher lateral mobility on the surfaces of apoptotic cells thereby promoting receptor clustering on the phagocyte. PS not only plays an important role in the engulfment process, but also acts as ‘tolerate me’ signal inducing the release of anti-inflammatory cytokines by phagocytes. An efficient and fast clearance of apoptotic cells is required to prevent secondary necrosis and leakage of intracellular danger signals into the surrounding tissue. Failure or prolongation of the clearance process leads to the release of intracellular antigens into the periphery provoking inflammation and development of systemic inflammatory autoimmune disease like systemic lupus erythematosus. Here we review the current findings concerning apoptosis-inducing pathways, important players of apoptotic cell recognition and clearance as well as the role of membrane remodeling in the engulfment of apoptotic cells by phagocytes.