Science.gov

Sample records for 14c-based source apportionment

  1. 14C-based Source Apportionment of Carbonaceous Aerosols in Switzerland for 2008 - 2012

    NASA Astrophysics Data System (ADS)

    Zotter, Peter; Ciobanu, Gabriela; Zhang, Yanlin; El-Haddad, Imad; Szidat, Sönke; Wacker, Lukas; Baltensperger, Urs; Prévôt, André

    2013-04-01

    Carbonaceous particles (total carbon, TC) are a major fraction of the fine aerosol and affect climate and human health. TC is classified into the sub-fractions elemental carbon (EC) and organic carbon (OC). EC originates only from fossil fuel combustion and biomass burning. OC can be emitted directly as primary organic aerosol from biogenic emissions, wood burning and fossil fuel combustion or can be formed in-situ in the atmosphere (secondary organic aerosol) (Szidat et al. 2006). Radiocarbon (14C) analysis is a direct and quantitative tool for distinguishing fossil and non-fossil sources, since 14C in fossil fuels is completely depleted whereas other sources have a contemporary 14C level. This study presents source apportionment results from the winter season over a time period of 5 years (2007/2008-2011/2012) using 14C measurements on aerosol filters collected simultaneously at 16 air quality monitoring stations across Switzerland. For every year 5 winter smog episode days were selected from which filters from all stations were analyzed. To resolve a good spatial variability 11 stations north and 5 stations south of the Alps were selected. This 14C data set is unique around the world concerning the number of analyzed filters and the duration. The filter sampling was conducted using high volume samplers with PM10 inlets and a time resolution of 24h. Separation of OC and EC was carried out using the THEODORE system (Szidat et al. 2004) and a Sunset EC/OC analyzer (Zhang et al. 2012), respectively. The resulting CO2 was cryo-trapped and sealed in glass ampoules for 14C measurements, performed with the Mini Carbon Dating System MICADAS (Ruff et al. 2007) at the Swiss Federal Institute of Technology (ETH) Zürich. The results for non-fossil (NF) OC (5 year average) are 81% ± 10% for north and 85% ± 8% for south of the Alps. ECNF values range from 31% to 53% north and from 36% to 66% south of the Alps. Both, the OCNF and ECNF show higher values south of the Alps

  2. Accuracy and precision of 14C-based source apportionment of organic and elemental carbon in aerosols using the Swiss_4S protocol

    NASA Astrophysics Data System (ADS)

    Mouteva, G. O.; Fahrni, S. M.; Santos, G. M.; Randerson, J. T.; Zhang, Y.-L.; Szidat, S.; Czimczik, C. I.

    2015-09-01

    Aerosol source apportionment remains a critical challenge for understanding the transport and aging of aerosols, as well as for developing successful air pollution mitigation strategies. The contributions of fossil and non-fossil sources to organic carbon (OC) and elemental carbon (EC) in carbonaceous aerosols can be quantified by measuring the radiocarbon (14C) content of each carbon fraction. However, the use of 14C in studying OC and EC has been limited by technical challenges related to the physical separation of the two fractions and small sample sizes. There is no common procedure for OC/EC 14C analysis, and uncertainty studies have largely focused on the precision of yields. Here, we quantified the uncertainty in 14C measurement of aerosols associated with the isolation and analysis of each carbon fraction with the Swiss_4S thermal-optical analysis (TOA) protocol. We used an OC/EC analyzer (Sunset Laboratory Inc., OR, USA) coupled to a vacuum line to separate the two components. Each fraction was thermally desorbed and converted to carbon dioxide (CO2) in pure oxygen (O2). On average, 91 % of the evolving CO2 was then cryogenically trapped on the vacuum line, reduced to filamentous graphite, and measured for its 14C content via accelerator mass spectrometry (AMS). To test the accuracy of our setup, we quantified the total amount of extraneous carbon introduced during the TOA sample processing and graphitization as the sum of modern and fossil (14C-depleted) carbon introduced during the analysis of fossil reference materials (adipic acid for OC and coal for EC) and contemporary standards (oxalic acid for OC and rice char for EC) as a function of sample size. We further tested our methodology by analyzing five ambient airborne particulate matter (PM2.5) samples with a range of OC and EC concentrations and 14C contents in an interlaboratory comparison. The total modern and fossil carbon blanks of our setup were 0.8 ± 0.4 and 0.67 ± 0.34 μg C, respectively

  3. Accuracy and precision of 14C-based source apportionment of organic and elemental carbon in aerosols using the Swiss_4S protocol

    NASA Astrophysics Data System (ADS)

    Mouteva, G. O.; Fahrni, S. M.; Santos, G. M.; Randerson, J. T.; Zhang, Y. L.; Szidat, S.; Czimczik, C. I.

    2015-04-01

    Aerosol source apportionment remains a critical challenge for understanding the transport and aging of aerosols, as well as for developing successful air pollution mitigation strategies. The contributions of fossil and non-fossil sources to organic carbon (OC) and elemental carbon (EC) in carbonaceous aerosols can be quantified by measuring the radiocarbon (14C) content of each carbon fraction. However, the use of 14C in studying OC and EC has been limited by technical challenges related to the physical separation of the two fractions and small sample sizes. There is no common procedure for OC/EC 14C analysis, and uncertainty studies have largely focused on the precision of yields. Here, we quantified the uncertainty in 14C measurement of aerosols associated with the isolation and analysis of each carbon fraction with the Swiss_4S thermal-optical analysis (TOA) protocol. We used an OC/EC analyzer (Sunset Laboratory Inc., OR, USA) coupled to vacuum line to separate the two components. Each fraction was thermally desorbed and converted to carbon dioxide (CO2) in pure oxygen (O2). On average 91% of the evolving CO2 was then cryogenically trapped on the vacuum line, reduced to filamentous graphite, and measured for its 14C content via accelerator mass spectrometry (AMS). To test the accuracy of our set-up, we quantified the total amount of extraneous carbon introduced during the TOA sample processing and graphitization as the sum of modern and fossil (14C-depleted) carbon introduced during the analysis of fossil reference materials (adipic acid for OC and coal for EC) and contemporary standards (oxalic acid for OC and rice char for EC) as a function of sample size. We further tested our methodology by analyzing five ambient airborne particulate matter (PM2.5) samples with a range of OC and EC concentrations and 14C contents in an interlaboratory comparison. The total modern and fossil carbon blanks of our set-up were 0.8 ± 0.4 and 0.67 ± 0.34 μg C, respectively

  4. 14C-Based source assessment of soot aerosols in Stockholm and the Swedish EMEP-Aspvreten regional background site

    NASA Astrophysics Data System (ADS)

    Andersson, August; Sheesley, Rebecca J.; Kruså, Martin; Johansson, Christer; Gustafsson, Örjan

    2011-01-01

    Combustion-derived soot or black carbon (BC) in the atmosphere has a strong influence on both climate and human health. In order to propose effective mitigation strategies for BC emissions it is of importance to investigate geographical distributions and seasonal variations of BC emission sources. Here, a radiocarbon methodology is used to distinguish between fossil fuel and biomass burning sources of soot carbon (SC). SC is isolated for subsequent off-line 14C quantification with the chemothermal oxidation method at 375 °C (CTO-375 method), which reflects a recalcitrant portion of the BC continuum known to minimize inadvertent inclusion of any non-pyrogenic organic matter. Monitored wind directions largely excluded impact from the Stockholm metropolitan region at the EMEP-Aspvreten rural station 70 km to the south-west. Nevertheless, the Stockholm city and the rural stations yielded similar relative source contributions with fraction biomass ( fbiomass) for fall and winter periods in the range of one-third to half. Large temporal variations in 14C-based source apportionment was noted for both the 6 week fall and the 4 month winter observations. The fbiomass appeared to be related to the SC concentration suggesting that periods of elevated BC levels may be caused by increased wood fuel combustion. These results for the largest metropolitan area in Scandinavia combine with other recent 14C-based studies of combustion-derived aerosol fractions to suggest that biofuel combustion is contributing a large portion of the BC load to the northern European atmosphere.

  5. Sensitivity of source apportionment results to mobile source profiles.

    PubMed

    Cai, Tianqi; Schauer, James J; Huang, Wei; Fang, Dongqing; Shang, Jing; Wang, Yuqin; Zhang, Yuanxun

    2016-12-01

    The sensitivity of a source apportionment model to mobile source profiles was examined to determine the impact of using non-local mobile source profiles in chemical mass balance (CMB) models. We examined the impact of USA and Chinese mobile source profiles on source apportionment results in St. Louis, Missouri, and Beijing. The results showed that the use of non-local mobile source profiles did not impact the model apportionment results for vegetative detritus and biomass burning, but other primary source contributions were influenced by the use of non-local source profiles. Secondary organic carbon (SOC) contributions estimated by the CMB models with local and non-local profiles were compared to estimate of SOC from the EC tracer method and were found to be consistent with little bias. The results also showed that it is feasible to use the USA mobile profiles in China while model results were biased by using Chinese mobile profiles in the USA. Monthly and annual average concentrations of molecular markers in the source apportionment model showed lower sensitivity to source profiles than daily measurements, which has implications to the design of source apportionment studies.

  6. "OZONE SOURCE APPORTIONMENT IN CMAQ'

    EPA Science Inventory

    Ozone source attribution has been used to support various policy purposes including interstate transport (Cross State Air Pollution Rule) by U.S. EPA and ozone nonattainment area designations by State agencies. Common scientific applications include tracking intercontinental tran...

  7. Source apportionment using reconstructed mass calculations.

    PubMed

    Siddique, Naila; Waheed, Shahida

    2014-01-01

    A long-term study was undertaken to investigate the air quality of the Islamabad/Rawalpindi area. In this regard fine and coarse particulate matter were collected from 4 sites in the Islamabad/Rawalpindi region from 1998 to 2010 using Gent samplers and polycarbonate filters and analyzed for their elemental composition using the techniques of Neutron Activation Analysis (NAA), Proton Induced X-ray Emission/Proton Induced Gamma-ray Emission (PIXE/PIGE) and X-ray Fluorescence (XRF) Spectroscopy. The elemental data along with the gravimetric measurements and black carbon (BC) results obtained by reflectance measurement were used to approximate or reconstruct the particulate mass (RCM) by estimation of pseudo sources such as soil, smoke, sea salt, sulfate and black carbon or soot. This simple analysis shows that if the analytical technique used does not measure important major elements then the data will not be representative of the sample composition and cannot be further utilized for source apportionment studies or to perform transboundary analysis. In this regard PIXE/PIGE and XRF techniques that can provide elemental compositional data for most of the major environmentally important elements appear to be more useful as compared to NAA. Therefore %RCM calculations for such datasets can be used as a quality assurance (QA) measure to treat data prior to application of chemometrical tools such as factor analysis (FA) or cluster analysis (CA).

  8. Source apportionment of particulate matter in Denmark

    NASA Astrophysics Data System (ADS)

    Moenster, J.; Glasius, M.; Nielsen, O. J.; Bilde, M.; Jensen, F. P.

    2005-12-01

    Atmospheric particulate matter (PM) has received considerable attention over the last decade as an important component of air pollution, particularly due to its health effects on the exposed population. Typically the mass of particles with diameters smaller that 10 μm (PM10) has been used in large cohort studies to estimate health effects such as increase in hospitalization rate, asthma attacks and premature deaths. Particles smaller than 2.5 μm (PM2.5) and ultra fine particles have been used in various epidemiological studies and correlations between exposure to fine and ultra fine particles and health effects have been found. Limits of acceptable concentrations of PM10, PM2.5 and some carcinogenic species have been made, and it is important to find the origin of the particulate matter to prevent exceeds of these limits. This can be done by measuring particle mass, organic/inorganic fractions of particles, the chemical components and other relevant factors, and then use receptor modeling for source apportionment of the particulate matter. We have done measurements at street level and urban background in Copenhagen, Denmark, to determine the origin of different sizes of particulate matter and the toxic organic compounds connected to these particles. We also did measurements in a small village with less traffic and more residential wood combustion for a comparison between traffic and wood combustion generated pollution. Our results show a significant amount of particulate matter coming from non local sources and are dominated by long-range transported inorganic salts. The amount of these is highly depended on the wind direction and thus on the origin of the wind plume. The origin of the carcinogenic organic compound benzo(a)pyrene was found to be local combustion sources. To prevent events of high particulate matter concentration in Copenhagen, Denmark, a reduction of emission from the local traffic will only lead to a minor effect, since the majority of the

  9. Rocky Mountain National Park reduced nitrogen source apportionment

    NASA Astrophysics Data System (ADS)

    Thompson, Tammy M.; Rodriguez, Marco A.; Barna, Michael G.; Gebhart, Kristi A.; Hand, Jennifer L.; Day, Derek E.; Malm, William C.; Benedict, Katherine B.; Collett, Jeffrey L., Jr.; Schichtel, Bret A.

    2015-05-01

    Excess wet and dry deposition of nitrogen-containing compounds are a concern at a number of national parks. The Rocky Mountain Atmospheric Nitrogen and Sulfur Study Part II (RoMANS II) campaign was conducted from November 2008 to November 2009 to characterize the composition of reactive nitrogen and sulfur deposited in Rocky Mountain National Park (RMNP). RoMANS II identified reduced nitrogen as the major contributor to reactive nitrogen deposition in RMNP, making up over 50% of the total. Motivated by this finding, the particulate source apportionment technology within the Comprehensive Air Quality Model with extensions was used here to estimate source apportionment of reduced nitrogen concentrations at RMNP. Source apportionment results suggest that approximately 40% of reduced nitrogen deposition to RMNP comes from ammonia sources within Colorado. However, the model evaluation also suggests that this number could be underrepresenting ammonia sources in eastern Colorado due to the difficulty of capturing upslope airflow on the eastern side of the Continental Divide with meteorological models. Emissions from California, the western model boundary, and the Snake River Valley in Idaho, the next three most influential sources, contribute approximately 15%, 8%, and 7%, respectively, to total reduced nitrogen measured in RMNP. Within Colorado, about 61%, 26%, and 13% of the total Colorado contribution comes from sources to the east of the Continental Divide, sources to the west of the Continental Divide, and from the park itself.

  10. Sensitivity of fine sediment source apportionment to mixing model assumptions

    NASA Astrophysics Data System (ADS)

    Cooper, Richard; Krueger, Tobias; Hiscock, Kevin; Rawlins, Barry

    2015-04-01

    Mixing models have become increasingly common tools for quantifying fine sediment redistribution in river catchments. The associated uncertainties may be modelled coherently and flexibly within a Bayesian statistical framework (Cooper et al., 2015). However, there is more than one way to represent these uncertainties because the modeller has considerable leeway in making error assumptions and model structural choices. In this presentation, we demonstrate how different mixing model setups can impact upon fine sediment source apportionment estimates via a one-factor-at-a-time (OFAT) sensitivity analysis. We formulate 13 versions of a mixing model, each with different error assumptions and model structural choices, and apply them to sediment geochemistry data from the River Blackwater, Norfolk, UK, to apportion suspended particulate matter (SPM) contributions from three sources (arable topsoils, road verges and subsurface material) under base flow conditions between August 2012 and August 2013 (Cooper et al., 2014). Whilst all 13 models estimate subsurface sources to be the largest contributor of SPM (median ~76%), comparison of apportionment estimates reveals varying degrees of sensitivity to changing prior parameter distributions, inclusion of covariance terms, incorporation of time-variant distributions and methods of proportion characterisation. We also demonstrate differences in apportionment results between a full and an empirical Bayesian setup and between a Bayesian and a popular Least Squares optimisation approach. Our OFAT sensitivity analysis reveals that mixing model structural choices and error assumptions can significantly impact upon fine sediment source apportionment results, with estimated median contributions in this study varying by up to 21% between model versions. Users of mixing models are therefore strongly advised to carefully consider and justify their choice of model setup prior to conducting fine sediment source apportionment investigations

  11. Quantification and radiocarbon source apportionment of black carbon in atmospheric aerosols using the CTO-375 method

    NASA Astrophysics Data System (ADS)

    Zencak, Zdenek; Elmquist, Marie; Gustafsson, Örjan

    To make progress towards linking the atmosphere and biogeosphere parts of the black carbon (BC) cycle, a chemothermal oxidation method (CTO-375), commonly applied for isolating BC from complex geomatrices such as soils, sediments and aquatic particles, was applied to investigate the BC also in atmospheric particles. Concentrations and 14C-based source apportionment of CTO-375 based BC was established for a reference aerosol (NIST RM-8785) and for wintertime aerosols collected in Stockholm and in a Swedish background area. The results were compared with thermal-optical (OC/EC) measurements. For NIST RM-8785, a good agreement was found between the BC CTO-375 concentration and the reported elemental carbon (EC) concentration measured by the "Speciation Trends Network—National Institute of Occupational Safety and Health" method (EC NIOSH) with BC CTO-375 of 0.054±0.002 g g -1 and EC NIOSH of 0.067±0.008 g g -1. In contrast, there was an average factor of ca. 20 difference between BC CTO-375 and EC NIOSH for the ambient Scandinavian wintertime aerosols, presumably reflecting a combination of BC CTO-375 isolating only the recalcitrant soot-BC portion of the BC continuum and the EC NIOSH metric inadvertently including some intrinsically non-pyrogenic organic matter. Isolation of BC CTO-375 with subsequent off-line radiocarbon analysis yielded fraction modern values (fM) for total organic carbon (TOC) of 0.93 (aerosols from a Swedish background area), and 0.58 (aerosols collected in Stockholm); whereas the fM for BC CTO-375 isolates were 1.08 (aerosols from a Swedish background area), and 0.87 (aerosols collected in Stockholm). This radiocarbon-based source apportionment suggests that contribution from biomass combustion to cold-season atmospheric BC CTO-375 in Stockholm was 70% and in the background area 88%.

  12. Radiocarbon source apportionment of urban and wildfire black and organic carbon aerosols

    NASA Astrophysics Data System (ADS)

    Mouteva, G.; Fahrni, S. M.; Santos, G.; Randerson, J. T.; Czimczik, C. I.

    2013-12-01

    Fossil and non-fossil sources of black carbon (BC) and organic carbon (OC) in carbonaceous aerosols can be quantified unambiguously by radiocarbon (14C) measurements. However, accurate 14C-based source apportionment requires a clear and reproducible physical separation of OC and BC, as well as minimal sample contaminations with non-sample carbon. To achieve a clear separation, we used a thermo-optical aerosol analyzer (Sunset Laboratory Inc, USA) with a newly established protocol (Swiss_4S protocol, Zhang et al., 2012), specifically optimized to completely separate the OC and BC fractions with minimal charring and maximum BC recovery. A simple and efficient vacuum line was coupled to the analyzer to trap produced CO2 with high yields and low carbon blanks. Upon trapping, CO2 samples sealed into glass ampoules were converted to graphite and measured for their radiocarbon content at the Keck Carbon Cycle Accelerator Mass Spectrometry Laboratory at the University of California, Irvine. Here, we present the results from the radiocarbon analysis of a set of 14C reference materials, blanks and inter-comparison samples for both OC and BC with sample sizes as small as 5 μg C. We will also present initial results from a set of urban aerosol samples from Salt Lake City, collected throughout 2012 and 2013, and from interior Alaska, collected during the summer of 2013 near the Stuart Creek 2 wildfire.

  13. Enterococcus and Escherichia coli fecal source apportionment with microbial source tracking genetic markers - is it feasible?

    EPA Science Inventory

    Fecal pollution is measured in surface waters using culture-based measurements of enterococci and Escherichia coli bacteria. Source apportionment of these two fecal indicator bacteria is an urgent need for prioritizing remediation efforts and quantifying health risks associated...

  14. Source apportionment of airborne particulates through receptor modeling: Indian scenario

    NASA Astrophysics Data System (ADS)

    Banerjee, Tirthankar; Murari, Vishnu; Kumar, Manish; Raju, M. P.

    2015-10-01

    Airborne particulate chemistry mostly governed by associated sources and apportionment of specific sources is extremely essential to delineate explicit control strategies. The present submission initially deals with the publications (1980s-2010s) of Indian origin which report regional heterogeneities of particulate concentrations with reference to associated species. Such meta-analyses clearly indicate the presence of reservoir of both primary and secondary aerosols in different geographical regions. Further, identification of specific signatory molecules for individual source category was also evaluated in terms of their scientific merit and repeatability. Source signatures mostly resemble international profile while, in selected cases lack appropriateness. In India, source apportionment (SA) of airborne particulates was initiated way back in 1985 through factor analysis, however, principal component analysis (PCA) shares a major proportion of applications (34%) followed by enrichment factor (EF, 27%), chemical mass balance (CMB, 15%) and positive matrix factorization (PMF, 9%). Mainstream SA analyses identify earth crust and road dust resuspensions (traced by Al, Ca, Fe, Na and Mg) as a principal source (6-73%) followed by vehicular emissions (traced by Fe, Cu, Pb, Cr, Ni, Mn, Ba and Zn; 5-65%), industrial emissions (traced by Co, Cr, Zn, V, Ni, Mn, Cd; 0-60%), fuel combustion (traced by K, NH4+, SO4-, As, Te, S, Mn; 4-42%), marine aerosols (traced by Na, Mg, K; 0-15%) and biomass/refuse burning (traced by Cd, V, K, Cr, As, TC, Na, K, NH4+, NO3-, OC; 1-42%). In most of the cases, temporal variations of individual source contribution for a specific geographic region exhibit radical heterogeneity possibly due to unscientific orientation of individual tracers for specific source and well exaggerated by methodological weakness, inappropriate sample size, implications of secondary aerosols and inadequate emission inventories. Conclusively, a number of challenging

  15. Indoor source apportionment in urban communities near industrial sites

    NASA Astrophysics Data System (ADS)

    Tunno, Brett J.; Dalton, Rebecca; Cambal, Leah; Holguin, Fernando; Lioy, Paul; Clougherty, Jane E.

    2016-08-01

    Because fine particulate matter (PM2.5) differs in chemical composition, source apportionment is frequently used for identification of relative contributions of multiple sources to outdoor concentrations. Indoor air pollution and source apportionment is often overlooked, though people in northern climates may spend up to 90% of their time inside. We selected 21 homes for a 1-week indoor sampling session during summer (July to September 2011), repeated in winter (January to March 2012). Elemental analysis was performed using inductively-coupled plasma mass spectrometry (ICP-MS), and factor analysis was used to determine constituent grouping. Multivariate modeling was run on factor scores to corroborate interpretations of source factors based on a literature review. For each season, a 5-factor solution explained 86-88% of variability in constituent concentrations. Indoor sources (i.e. cooking, smoking) explained greater variability than did outdoor sources in these industrial communities. A smoking factor was identified in each season, predicted by number of cigarettes smoked. Cooking factors were also identified in each season, explained by frequency of stove cooking and stovetop frying. Significant contributions from outdoor sources including coal and motor vehicles were also identified. Higher coal and secondary-related elemental concentrations were detected during summer than winter. Our findings suggest that source contributions to indoor concentrations can be identified and should be examined in relation to health effects.

  16. The Albuquerque carbon monoxide source apportionment study

    SciTech Connect

    Einfeld, W.

    1988-07-01

    At the request of the New Mexico Environmental Improvement Division, a study was carried out to examine, in detail, the relative contribution of various combustion sources to ambient carbon monoxide in Albuquerque during the winter season evening hours. The two-month field study (January--February 1985) included aerosol and gas monitoring at two sites in the Albuquerque area. Source contributions to ambient carbon monoxide were determined by regression techniques using tracer elements and by carbon isotope measurements on collected carbon monoxide. Results from isotopic carbon analysis of carbon monoxide show that, on average, mobile sources contributed 68 percent and wood burning sources 32 percent to ambient carbon monoxide levels during winter season evening hours. Good agreement was found between results from carbon isotope and linear regression techniques used to estimate average source strengths. The study results point to the significance of both mobile and residential wood burning sources as contributors to ambient carbon monoxide levels. 1 ref., 10 figs., 19 tabs.

  17. Photochemical grid model implementation and application of VOC, NOx, and O3 source apportionment

    EPA Science Inventory

    For the purposes of developing optimal emissions control strategies, efficient approaches are needed to identify the major sources or groups of sources that contribute to elevated ozone (O3) concentrations. Source-based apportionment techniques implemented in photochemical grid m...

  18. Source Apportionment of VOCs in Edmonton, Alberta

    NASA Astrophysics Data System (ADS)

    McCarthy, M. C.; Brown, S. G.; Aklilu, Y.; Lyder, D. A.

    2012-12-01

    Regional emissions at Edmonton, Alberta, are complex, containing emissions from (1) transportation sources, such as cars, trucks, buses, and rail; (2) industrial sources, such as petroleum refining, light manufacturing, and fugitive emissions from holding tanks or petroleum terminals; and (3) miscellaneous sources, such as biogenic emissions and natural gas use and processing. From 2003 to 2009, whole air samples were collected at two sites in Edmonton and analyzed for over 77 volatile organic compounds (VOCs). VOCs were sampled in the downtown area (Central) and the industrial area on the eastern side of the city (East). Concentrations of most VOCs were highest at the East site. The positive matrix factorization (PMF) receptor model was used to apportion ambient concentration measurements of VOCs into eleven factors, which were associated with emissions source categories. Factors of VOCs identified in the final eleven-factor solution include transportation sources (both gasoline and diesel vehicles), industrial sources, a biogenic source, and a natural-gas-related source. Transportation sources accounted for more mass at the Central site than at the East site; this was expected because Central is in a core urban area where transportation emissions are concentrated. Transportation sources accounted for nearly half of the VOC mass at the Central site, but only 6% of the mass at the East site. Encouragingly, mass from transportation sources has declined by about 4% a year in this area; this trend is similar to the decline found throughout the United States, and is likely due to fleet turnover as older, more highly polluting cars are replaced with newer, cleaner cars. In contrast, industrial sources accounted for ten times more VOC mass at the East site than at the Central site and were responsible for most of the total VOC mass observed at the East site. Of the six industrial factors identified at the East site, four were linked to petrochemical industry production

  19. RADIOCARBON SOURCE APPORTIONMENT IN A BIOFUELS ERA

    EPA Science Inventory

    Biofuels (gasohol and biodiesel) introduce radiocarbon into the U.S. mobile source fuel supply where it was previously absent. Initial measurements of radiocarbon in the PM2.5 combustion emissions from engines using gasohol indicate that this may have less effect on r...

  20. SOURCE APPORTIONMENT RESULTS, UNCERTAINTIES, AND MODELING TOOLS

    EPA Science Inventory

    Advanced multivariate receptor modeling tools are available from the U.S. Environmental Protection Agency (EPA) that use only speciated sample data to identify and quantify sources of air pollution. EPA has developed both EPA Unmix and EPA Positive Matrix Factorization (PMF) and ...

  1. Iodine source apportionment in the Malawian diet

    PubMed Central

    Watts, M. J.; Joy, E. J. M.; Young, S. D.; Broadley, M. R.; Chilimba, A. D. C.; Gibson, R. S.; Siyame, E. W. P.; Kalimbira, A. A.; Chilima, B.; Ander, E. L.

    2015-01-01

    The aim of this study was to characterise nutritional-I status in Malawi. Dietary-I intakes were assessed using new datasets of crop, fish, salt and water-I concentrations, while I status was assessed for 60 women living on each of calcareous and non-calcareous soils as defined by urinary iodine concentration (UIC). Iodine concentration in staple foods was low, with median concentrations of 0.01 mg kg−1 in maize grain, 0.008 mg kg−1 in roots and tubers, but 0.155 mg kg−1 in leafy vegetables. Freshwater fish is a good source of dietary-I with a median concentration of 0.51 mg kg−1. Mean Malawian dietary-Iodine intake from food, excluding salt, was just 7.8 μg d−1 compared to an adult requirement of 150 μg d−1. Despite low dietary-I intake from food, median UICs were 203 μg L−1 with only 12% defined as I deficient whilst 21% exhibited excessive I intake. Iodised salt is likely to be the main source of dietary I intake in Malawi; thus, I nutrition mainly depends on the usage and concentration of I in iodised salt. Drinking water could be a significant source of I in some areas, providing up to 108 μg d−1 based on consumption of 2 L d−1. PMID:26503697

  2. Iodine source apportionment in the Malawian diet

    NASA Astrophysics Data System (ADS)

    Watts, M. J.; Joy, E. J. M.; Young, S. D.; Broadley, M. R.; Chilimba, A. D. C.; Gibson, R. S.; Siyame, E. W. P.; Kalimbira, A. A.; Chilima, B.; Ander, E. L.

    2015-10-01

    The aim of this study was to characterise nutritional-I status in Malawi. Dietary-I intakes were assessed using new datasets of crop, fish, salt and water-I concentrations, while I status was assessed for 60 women living on each of calcareous and non-calcareous soils as defined by urinary iodine concentration (UIC). Iodine concentration in staple foods was low, with median concentrations of 0.01 mg kg-1 in maize grain, 0.008 mg kg-1 in roots and tubers, but 0.155 mg kg-1 in leafy vegetables. Freshwater fish is a good source of dietary-I with a median concentration of 0.51 mg kg-1. Mean Malawian dietary-Iodine intake from food, excluding salt, was just 7.8 μg d-1 compared to an adult requirement of 150 μg d-1. Despite low dietary-I intake from food, median UICs were 203 μg L-1 with only 12% defined as I deficient whilst 21% exhibited excessive I intake. Iodised salt is likely to be the main source of dietary I intake in Malawi; thus, I nutrition mainly depends on the usage and concentration of I in iodised salt. Drinking water could be a significant source of I in some areas, providing up to 108 μg d-1 based on consumption of 2 L d-1.

  3. Source apportionment of ambient volatile organic compounds in Beijing.

    PubMed

    Song, Yu; Shao, Min; Liu, Ying; Lu, Sihua; Kuster, William; Goldan, Paul; Xie, Shaodong

    2007-06-15

    The ambient air quality standard for ozone is frequently exceeded in Beijing in summer and autumn. Source apportionments of volatile organic compounds (VOCs), which are precursors of ground-level ozone formation, can be helpful to the further study of tropospheric ozone formation. In this study, ambient concentrations of VOCs were continuously measured with a time resolution of 30 min in August 2005 in Beijing. By using positive matrix factorization (PMF), eight sources for the selected VOC species were extracted. Gasoline-related emissions (the combination of gasoline exhaust and gas vapor), petrochemicals, and liquefied petroleum gas (LPG) contributed 52, 20, and 11%, respectively, to total ambient VOCs. VOC emissions from natural gas (5%), painting (5%), diesel vehicles (3%), and biogenic emissions (2%) were also identified. The gasoline-related, petrochemical, and biogenic sources were estimated to be the major contributors to ozone formation potentials in Beijing.

  4. A model-based approach for imputing censored data in source apportionment studies

    PubMed Central

    Krall, Jenna R.; Simpson, Charles H.

    2015-01-01

    Sources of particulate matter (PM) air pollution are generally inferred from PM chemical constituent concentrations using source apportionment models. Concentrations of PM constituents are often censored below minimum detection limits (MDL) and most source apportionment models cannot handle these censored data. Frequently, censored data are first substituted by a constant proportion of the MDL or are removed to create a truncated dataset before sources are estimated. When estimating the complete data distribution, these commonly applied methods to adjust censored data perform poorly compared with model-based imputation methods. Model-based imputation has not been used in source apportionment and may lead to better source estimation. However if the censored chemical constituents are not important for estimating sources, censoring adjustment methods may have little impact on source estimation. We focus on two source apportionment models applied in the literature and provide a comprehensive assessment of how censoring adjustment methods, including model-based imputation, impact source estimation. A review of censoring adjustment methods critically informs how censored data should be handled in these source apportionment models. In a simulation study, we demonstrated that model-based multiple imputation frequently leads to better source estimation compared with commonly used censoring adjustment methods. We estimated sources of PM in New York City and found estimated source distributions differed by censoring adjustment method. In this study, we provide guidance for adjusting censored PM constituent data in common source apportionment models, which is necessary for estimation of PM sources and their subsequent health effects. PMID:26640398

  5. A model-based approach for imputing censored data in source apportionment studies.

    PubMed

    Krall, Jenna R; Simpson, Charles H; Peng, Roger D

    2015-12-01

    Sources of particulate matter (PM) air pollution are generally inferred from PM chemical constituent concentrations using source apportionment models. Concentrations of PM constituents are often censored below minimum detection limits (MDL) and most source apportionment models cannot handle these censored data. Frequently, censored data are first substituted by a constant proportion of the MDL or are removed to create a truncated dataset before sources are estimated. When estimating the complete data distribution, these commonly applied methods to adjust censored data perform poorly compared with model-based imputation methods. Model-based imputation has not been used in source apportionment and may lead to better source estimation. However if the censored chemical constituents are not important for estimating sources, censoring adjustment methods may have little impact on source estimation. We focus on two source apportionment models applied in the literature and provide a comprehensive assessment of how censoring adjustment methods, including model-based imputation, impact source estimation. A review of censoring adjustment methods critically informs how censored data should be handled in these source apportionment models. In a simulation study, we demonstrated that model-based multiple imputation frequently leads to better source estimation compared with commonly used censoring adjustment methods. We estimated sources of PM in New York City and found estimated source distributions differed by censoring adjustment method. In this study, we provide guidance for adjusting censored PM constituent data in common source apportionment models, which is necessary for estimation of PM sources and their subsequent health effects.

  6. On the isolation of OC and EC and the optimal strategy of radiocarbon-based source apportionment of carbonaceous aerosols

    NASA Astrophysics Data System (ADS)

    Zhang, Y. L.; Perron, N.; Ciobanu, V. G.; Zotter, P.; Minguillón, M. C.; Wacker, L.; Prévôt, A. S. H.; Baltensperger, U.; Szidat, S.

    2012-07-01

    Radiocarbon (14C) measurements of elemental carbon (EC) and organic carbon (OC) separately (as opposed to only total carbon, TC) allow an unambiguous quantification of their non-fossil and fossil sources and represent an improvement in carbonaceous aerosol source apportionment. Isolation of OC and EC for accurate 14C determination requires complete removal of interfering fractions with maximum recovery. To evaluate the extent of positive and negative artefacts during OC and EC separation, we performed sample preparation with a commercial Thermo-Optical OC/EC Analyser (TOA) by monitoring the optical properties of the sample during the thermal treatments. Extensive attention has been devoted to the set-up of TOA conditions, in particular, heating program and choice of carrier gas. Based on different types of carbonaceous aerosols samples, an optimised TOA protocol (Swiss_4S) with four steps is developed to minimise the charring of OC, the premature combustion of EC and thus artefacts of 14C-based source apportionment of EC. For the isolation of EC for 14C analysis, the water-extraction treatment on the filter prior to any thermal treatment is an essential prerequisite for subsequent radiocarbon; otherwise the non-fossil contribution may be overestimated due to the positive bias from charring. The Swiss_4S protocol involves the following consecutive four steps (S1, S2, S3 and S4): (1) S1 in pure oxygen (O2) at 375 °C for separation of OC for untreated filters, and water-insoluble organic carbon (WINSOC) for water-extracted filters; (2) S2 in O2 at 475 °C, followed by (3) S3 in helium (He) at 650 °C, aiming at complete OC removal before EC isolation and leading to better consistency with thermal-optical protocols like EUSAAR_2, compared to pure oxygen methods; and (4) S4 in O2 at 760 °C for recovery of the remaining EC. WINSOC was found to have a significantly higher fossil contribution than the water-soluble OC (WSOC). Moreover, the experimental results

  7. On the isolation of OC and EC and the optimal strategy of radiocarbon-based source apportionment of carbonaceous aerosols

    NASA Astrophysics Data System (ADS)

    Zhang, Y. L.; Perron, N.; Ciobanu, V. G.; Zotter, P.; Minguillón, M. C.; Wacker, L.; Prévôt, A. S. H.; Baltensperger, U.; Szidat, S.

    2012-11-01

    Radiocarbon (14C) measurements of elemental carbon (EC) and organic carbon (OC) separately (as opposed to only total carbon, TC) allow an unambiguous quantification of their non-fossil and fossil sources and represent an improvement in carbonaceous aerosol source apportionment. Isolation of OC and EC for accurate 14C determination requires complete removal of interfering fractions with maximum recovery. The optimal strategy for 14C-based source apportionment of carbonaceous aerosols should follow an approach to subdivide TC into different carbonaceous aerosol fractions for individual 14C analyses, as these fractions may differ in their origins. To evaluate the extent of positive and negative artefacts during OC and EC separation, we performed sample preparation with a commercial Thermo-Optical OC/EC Analyser (TOA) by monitoring the optical properties of the sample during the thermal treatments. Extensive attention has been devoted to the set-up of TOA conditions, in particular, heating program and choice of carrier gas. Based on different types of carbonaceous aerosols samples, an optimised TOA protocol (Swiss_4S) with four steps is developed to minimise the charring of OC, the premature combustion of EC and thus artefacts of 14C-based source apportionment of EC. For the isolation of EC for 14C analysis, the water-extraction treatment on the filter prior to any thermal treatment is an essential prerequisite for subsequent radiocarbon measurements; otherwise the non-fossil contribution may be overestimated due to the positive bias from charring. The Swiss_4S protocol involves the following consecutive four steps (S1, S2, S3 and S4): (1) S1 in pure oxygen (O2) at 375 °C for separation of OC for untreated filters and water-insoluble organic carbon (WINSOC) for water-extracted filters; (2) S2 in O2 at 475 °C followed by (3) S3 in helium (He) at 650 °C, aiming at complete OC removal before EC isolation and leading to better consistency with thermal-optical protocols

  8. Critical review of black carbon and elemental carbon source apportionment in Europe and the United States

    NASA Astrophysics Data System (ADS)

    Briggs, Nicole L.; Long, Christopher M.

    2016-11-01

    An increasing number of air pollution source apportionment studies in Europe and the United States have focused on the black carbon (BC) fraction of ambient particulate matter (PM) given its linkage with adverse public health and climate impacts. We conducted a critical review of European and US BC source apportionment studies published since 2003. Since elemental carbon (EC) has been used as a surrogate measure of BC, we also considered source apportionment studies of EC measurements. This review extends the knowledge presented in previous ambient PM source apportionment reviews because we focus on BC and EC and critically examine the differences between source apportionment results for different methods and source categories. We identified about 50 BC and EC source apportionment studies that have been conducted in either Europe or the US since 2003, finding a striking difference in the commonly used source apportionment methods between the two regions and variations in the assigned source categories. Using three dominant methodologies (radiocarbon, aethalometer, and macro-tracer methods) that only allow for BC to be broadly apportioned into either fossil fuel combustion or biomass burning source categories, European studies generally support fossil fuel combustion as the dominant ambient BC source, but also show significant biomass burning contributions, in particular in wintertime at non-urban locations. Among US studies where prevailing methods such as chemical mass balance (CMB) and positive matrix factorization (PMF) models have allowed for estimation of more refined source contributions, there are fewer findings showing the significance of biomass burning and variable findings on the relative proportion of BC attributed to diesel versus gasoline emissions. Overall, the available BC source apportionment studies provide useful information demonstrating the significance of both fossil fuel combustion and biomass burning BC emission sources in Europe and the US

  9. Source apportionment of carbonaceous aerosols over South and East Asia using dual carbon isotopes

    NASA Astrophysics Data System (ADS)

    Gustafsson, O.; Kirillova, E. N.; Andersson, A.-; Kruså, M.; Sheesley, R. J.; Tiwari, S.-; Lee, M.; Chen, B.; Du, K.

    2012-12-01

    Emissions of black carbon (BC) and other components of carbonaceous aerosols affect both climate and health in South and East Asia, yet substantial uncertainties exist regarding their sources. The relative contribution to atmospheric BC from fossil fuel versus biomass combustion is important to constrain both to direct mitigation and as their different properties make their effects on climate forcing and respiratory health different. This study approached the sourcing challenge by applying microscale radiocarbon measurements to aerosol particles collected in both source regions and at regional receptor observatories of both S Asia (New Delhi and the Maldives Climate Observatory) and of E Asia (Beijing, Shanghai, South China Coastal Observatory and the Korea Climate Observatory - Gosan, KCO-G, Jeju Island). The radiocarbon approach is ideally suited to this task as fossil sources are void of 14C whereas biomass combustion products hold a contemporary 14C signal. For S Asia, the 14C-based observations suggest that biomass combustion contributes half to two-thirds of the BC loading. In contrast, for E Asia, fossil fuel combustion account for four-fifths of the BC emitted from China. This source-diagnostic radiocarbon signal in the ambient aerosol over East Asia establishes a much larger role for fossil fuel combustion than suggested by all fifteen BC emission inventory models. There are also poor constraints on the sources of water-soluble organic carbon (WSOC), a large hydrophilic component of carbonaceous aerosols that enhances the propensity of aerosols to form clouds. In a 15-mo continuous campaign in S Asia, radiocarbon-based source apportionment of WSOC shows the dominance of biogenic/biomass combustion sources but also a substantial anthropogenic fossil-fuel contribution (about 20%). WSOC in E Asia reaching KCO-G were 50% from fossil sources. Aerosols reaching the Maldives after long-range over-ocean transport were enriched by 3-4‰ in δ13C-WSOC. This is

  10. IMPROVING SOURCE PROFILES AND APPORTIONMENT OF COMBUSTION SOURCES USING THERMAL CARBON FRACTIONS IN MULTIVARIATE RECEPTOR MODELS

    EPA Science Inventory

    The purpose of this study was to improve combustion source profiles and apportionment of a PM2.5 urban aerosol by using 7 individual organic and elemental carbon thermal fractions in place of total organic and elemental carbon. This study used 3 years (96-99) of speciated data...

  11. Receptor model source apportionment of nonmethane hydrocarbons in Mexico City.

    PubMed

    Mugica, V; Watson, J; Vega, E; Reyes, E; Ruiz, M E; Chow, J

    2002-03-29

    With the purpose of estimating the source contributions of nonmethane hydrocarbons (NMHC) to the atmosphere at three different sites in the Mexico City Metropolitan Area, 92 ambient air samples were measured from February 23 to March 22 of 1997. Light- and heavy-duty vehicular profiles were determined to differentiate the NMHC contribution of diesel and gasoline to the atmosphere. Food cooking source profiles were also determined for chemical mass balance receptor model application. Initial source contribution estimates were carried out to determine the adequate combination of source profiles and fitting species. Ambient samples of NMHC were apportioned to motor vehicle exhaust, gasoline vapor, handling and distribution of liquefied petroleum gas (LP gas), asphalt operations, painting operations, landfills, and food cooking. Both gasoline and diesel motor vehicle exhaust were the major NMHC contributors for all sites and times, with a percentage of up to 75%. The average motor vehicle exhaust contributions increased during the day. In contrast, LP gas contribution was higher during the morning than in the afternoon. Apportionment for the most abundant individual NMHC showed that the vehicular source is the major contributor to acetylene, ethylene, pentanes, n-hexane, toluene, and xylenes, while handling and distribution of LP gas was the major source contributor to propane and butanes. Comparison between CMB estimates of NMHC and the emission inventory showed a good agreement for vehicles, handling and distribution of LP gas, and painting operations; nevertheless, emissions from diesel exhaust and asphalt operations showed differences, and the results suggest that these emissions could be underestimated.

  12. Source apportionment modeling of volatile organic compounds in streams

    USGS Publications Warehouse

    Pankow, J.F.; Asher, W.E.; Zogorski, J.S.

    2006-01-01

    It often is of interest to understand the relative importance of the different sources contributing to the concentration cw of a contaminant in a stream; the portions related to sources 1, 2, 3, etc. are denoted cw,1, cw,2, cw,3, etc. Like c w, 'he fractions ??1, = cw,1/c w, ??2 = cw,2/cw, ??3 = cw,3/cw, etc. depend on location and time. Volatile organic compounds (VOCs) can undergo absorption from the atmosphere into stream water or loss from stream water to the atmosphere, causing complexities affecting the source apportionment (SA) of VOCs in streams. Two SA rules are elaborated. Rule 1: VOC entering a stream across the air/water interface exclusively is assigned to the atmospheric portion of cw. Rule 2: VOC loss by volatilization, flow loss to groundwater, in-stream degradation, etc. is distributed over cw,1 cw,2, c w,3, etc. in proportion to their corresponding ?? values. How the two SA rules are applied, as well as the nature of the SA output for a given case, will depend on whether transport across the air/water interface is handled using the net flux F convention or using the individual fluxes J convention. Four hypothetical stream cases involving acetone, methyl-tert-butyl ether (MTBE), benzene, chloroform, and perchloroethylene (PCE) are considered. Acetone and MTBE are sufficiently water soluble from air for a domestic atmospheric source to be capable of yielding cw values approaching the common water quality guideline range of 1 to 10 ??g/L. For most other VOCs, such levels cause net outgassing (F > 0). When F > 0 in a given section of stream, in the net flux convention, all of the ??j, for the compound remain unchanged over that section while cw decreases. A characteristic time ??d can be calculated to predict when there will be differences between SA results obtained by the net flux convention versus the individual fluxes convention. Source apportionment modeling provides the framework necessary for comparing different strategies for mitigating

  13. Source apportionment of atmospheric particles in the UK and Pakistan

    SciTech Connect

    Smith, D.J.T.; Harrison, R.M.; Luhana, L.

    1995-12-31

    Intensive seasonal sampling was undertaken at urban and rural locations throughout Birmingham (UK). Dichotomous Stacked Filter Units (DSFUS) were run simultaneously with hi-vol samplers. DSFU filters were analyzed for nineteen metal species, ammonium and various anions. Hi-vol samplers were modified in order to collect particulate and vapor phase PAHs by means of filter papers and polyurethane foam plugs. Eighteen PAH species were determined by reversed-phase HPLC. Filter portions were forwarded to the University of Aveiro for analysis of elemental and organic carbon. Hi-vol air sampling equipment was run at three sites in Lahore (Pakistan) for over a year. Selected metals, anions and ammonium were quantified, along with eighteen species of particle-associated PAH. Chemical source apportionment of both the Birmingham and Lahore aerosol loads was completed using multivariate analysis. Metals and anionic data were utilized, along with organic concentrations and meteorological data. This technique typically enabled six major air pollution source categories to be identified, along with the quantitative contributions of pollutant species to each source group. The combination of measurements of PAH and inorganic pollutants proved to be a far more powerful tracer of emission sources than PAH data alone. The largest contribution to aerosol mass in the coarse sized fraction in Birmingham was observed to be soil. Whereas in the fine sized fraction major contributors are vehicular/road dust followed by secondary aerosol formation plus oil combustion. Multivariate analysis of the Lahore data revealed similar source categories to those found in Birmingham. The largest contribution to aerosol mass at all three Punjabi sites was soil. This source is followed by metallurgical processes, vehicular emissions and refuse burning.

  14. An atmospheric lead source-areas apportionment study in Europe

    NASA Astrophysics Data System (ADS)

    Flament, P.; Deboudt, K.; Bertho, M.-L.; Véron, A.; Puskaric, E.

    2003-05-01

    Atmospheric particulate matter samples, for which the origin of aerosols was unambiguousty determined, has been collected in the Eastern Channel (Northem France). Associated lead concentrations are higher by a factor of about 7, when air masses are runnig from continental Europe, by comparison with marine air masses. We statistically evidence that air masses originating from continental Europe exhibit a more radiogenic composition (1.134<^{206}Pb/^{207}Pb<1.172) than air masses coming from British Islands (1.106<^{206}Pb/^{207}Pb<1.1243. Generally, lead isotopic compositions in aerosols are dearly distinct from the gasoline signatures in European countries, strongly suggesting that automotive lead is no more the major component of this metal in the air. Gasoline and industrial isotopic signatures could explain the origin of lead in our aerosol samples. A source apportionment based upon ^{206}Pb/^{207}Pb ratios suggests that thé difference between British (^{206}Pb/^{207}Pb = 1.122 ± 0.038) and continental (^{206}Pb/^{207}Pb = 1.155 ± 0.022) signatures may be explained by differenees iro the petrol leard content of aerosols (23 to 62% in Great Britain versus 10 to 36% in continental Europe).

  15. DEVELOPMENT AND EVALUATION OF PM 2.5 SOURCE APPORTIONMENT METHODOLOGIES

    EPA Science Inventory

    The receptor model called Positive Matrix Factorization (PMF) has been extensively used to apportion sources of ambient fine particulate matter (PM2.5), but the accuracy of source apportionment results currently remains unknown. In addition, air quality forecast model...

  16. MONITORING AND SOURCE APPORTIONMENT OF PARTICULATE MATTER NEAR A LARGE PHOSPHORUS PRODUCTION FACILITY

    EPA Science Inventory

    A source apportionment study was conducted to identify sources within a large elemental phosphorus plant that contribute to exceedances of the National Ambient Air Quality Standard for 24-h PM10. Ambient data were collected at three monitoring sites from October 1996 through Ju...

  17. Synthesizing Scientific Progress: Outcomes from US EPA’s Carbonaceous Aerosols and Source Apportionment STAR Grants

    EPA Science Inventory

    ABSTRACTA number of studies in the past decade have transformed the way we think about atmospheric aerosols. The advances include, but are not limited to, source apportionment of organics using aerosol mass spectrometer data, the volatility basis set approach, quantifying isopre...

  18. SOURCE APPORTIONMENT OF SEATTLE PM 2.5 USING STN ORGANIC CARBON PEAKS

    EPA Science Inventory

    Results from the Source Apportionment of Seattle PM2.5 Using STN Organic Carbon Peaks study will be presented at the American Association for Aerosol Research (AAAR) 24th Annual Conference in Austin, Texas (Oct 17 - 21, 2005). Receptor modeling results from Seattle us...

  19. Weak acid extractable metals in Bramble Bay, Queensland, Australia: temporal behaviour, enrichment and source apportionment.

    PubMed

    Brady, James P; Ayoko, Godwin A; Martens, Wayde N; Goonetilleke, Ashantha

    2015-02-15

    Sediment samples were taken from six sampling sites in Bramble Bay, Queensland, Australia between February and November in 2012. They were analysed for a range of heavy metals including Al, Fe, Mn, Ti, Ce, Th, U, V, Cr, Co, Ni, Cu, Zn, As, Cd, Sb, Te, Hg, Tl and Pb. Fraction analysis, Enrichment Factors and Principal Component Analysis-Absolute Principal Component Scores (PCA-APCS) were carried out in order to assess metal pollution, potential bioavailability and source apportionment. Cr and Ni exceeded the Australian Interim Sediment Quality Guidelines at some sampling sites, while Hg was found to be the most enriched metal. Fraction analysis identified increased weak acid soluble Hg and Cd during the sampling period. Source apportionment via PCA-APCS found four sources of metals pollution, namely, marine sediments, shipping, antifouling coatings and a mixed source. These sources need to be considered in any metal pollution control measure within Bramble Bay.

  20. Workgroup Report: Workshop on Source Apportionment of Particulate Matter Health Effects—Intercomparison of Results and Implications

    PubMed Central

    Thurston, George D.; Ito, Kazuhiko; Mar, Therese; Christensen, William F.; Eatough, Delbert J.; Henry, Ronald C.; Kim, Eugene; Laden, Francine; Lall, Ramona; Larson, Timothy V.; Liu, Hao; Neas, Lucas; Pinto, Joseph; Stölzel, Matthias; Suh, Helen; Hopke, Philip K.

    2005-01-01

    Although the association between exposure to ambient fine particulate matter with aerodynamic diameter < 2.5 μm (PM2.5) and human mortality is well established, the most responsible particle types/sources are not yet certain. In May 2003, the U.S. Environmental Protection Agency’s Particulate Matter Centers Program sponsored the Workshop on the Source Apportionment of PM Health Effects. The goal was to evaluate the consistency of the various source apportionment methods in assessing source contributions to daily PM2.5 mass–mortality associations. Seven research institutions, using varying methods, participated in the estimation of source apportionments of PM2.5 mass samples collected in Washington, DC, and Phoenix, Arizona, USA. Apportionments were evaluated for their respective associations with mortality using Poisson regressions, allowing a comparative assessment of the extent to which variations in the apportionments contributed to variability in the source-specific mortality results. The various research groups generally identified the same major source types, each with similar elemental makeups. Intergroup correlation analyses indicated that soil-, sulfate-, residual oil-, and salt-associated mass were most unambiguously identified by various methods, whereas vegetative burning and traffic were less consistent. Aggregate source-specific mortality relative risk (RR) estimate confidence intervals overlapped each other, but the sulfate-related PM2.5 component was most consistently significant across analyses in these cities. Analyses indicated that source types were a significant predictor of RR, whereas apportionment group differences were not. Variations in the source apportionments added only some 15% to the mortality regression uncertainties. These results provide supportive evidence that existing PM2.5 source apportionment methods can be used to derive reliable insights into the source components that contribute to PM2.5 health effects. PMID:16330361

  1. The qualitative and quantitative source apportionments of polycyclic aromatic hydrocarbons in size dependent road deposited sediment.

    PubMed

    Zhang, Jin; Wang, Jing; Hua, Pei; Krebs, Peter

    2015-02-01

    This study showcases the qualitative and quantitative source apportionments of size-dependent polycyclic aromatic hydrocarbons (PAHs) in road deposited sediment by means of molecular diagnostic ratio (MDR) and positive matrix factorisation (PMF) approaches. The MDR was initially used to narrow the PAH source candidates. PMF modelling was subsequently used to provide more precise source apportionment with the assistance of a multiple linear regression analysis. Through a combined qualitative and quantitative source apportionment, different potential source contributors were identified at different size fractions. Explicitly, three major contributors to sorption at the size fraction of 1000-400 μm were tentatively identified as incineration (26%), coal combustion (53%) and gasoline-powered vehicle (20%). Four major contributors to the size fraction of 400-100 μm were identified as gasoline-powered vehicle (25%), surface pavement (15%), diesel-powered vehicle (37%) and industrial boiler (24%). Four major contributors to the size fraction of 100-63 μm were identified as cogeneration emission (13%), diesel-powered vehicle (28%), tire debris (45%) and wood combustion (14%). The potential contributors in the size fraction 63-0.45 μm were identified as diesel-powered vehicle (21%), heterogeneous sources (41%) and biomass burning (38%). In addition, the highest ∑16PAH concentration was found in the smallest size fraction of 63-0.45 μm, which is also where the highest BaPE and TEF values for potential risk assessment occurred.

  2. Carbon isotope based aerosol source apportionment in Eastern European city Vilnius

    NASA Astrophysics Data System (ADS)

    Garbaras, Andrius; Sapolaite, Justina; Garbariene, Inga; Ezerinskis, Zilvinas; Pocevicius, Matas; Krikscikas, Laurynas; Jacevicius, Sarunas; Plukis, Arturas; Remeikis, Vidmantas

    2016-04-01

    We present carbonaceous aerosol source apportionment results in Eastern European city Vilnius (capital of Lithuania) using stable carbon isotope ratio (δ13C) and radiocarbon (14C) methods. The aerosol sampling campaigns were performed in 2014-2016 winter seasons in Vilnius. PM1 particles were collected on quartz fiber filters using high volume sampler, while PM10 and size segregated aerosol particles were collected using low volume and MOUDI 128 cascade impactor respectively. δ13C values were measured with EA-IRMS system while radiocarbon analysis was performed using Single Stage Accelerator Mass Spectrometer (SSAMS). For the AMS analysis, filters (or aluminium foils from cascade impactor) were graphitized using Automated Graphitization Equipment. It was estimated that dominant carbonaceous aerosol source in Vilnius was of biogenic/biomass origin (60-90 %). Fossil fuel sources accounted for up to 23 % of total carbon fraction. Combining stable carbon and radiocarbon isotope analysis we were able to quantify the amount of coal derived aerosol particles. The contribution of coal burning emissions were up to 14 %. We will present the applicability of dual carbon (13C and 14C) isotope ratio method for the aerosol source apportionment in different regions of Europe, also the perspectives of using MOUDI cascade impactors to make source apportionment in size segregated aerosol particles.

  3. Source contributions and spatiotemporal characteristics of PAHs in sediments: Using three-way source apportionment approach.

    PubMed

    Tian, Ying-Ze; Shi, Guo-Liang; Liu, Gui-Rong; Guo, Chang-Sheng; Peng, Xing; Xu, Jian; Zhang, Yuan; Feng, Yin-Chang

    2014-08-01

    Polycyclic aromatic hydrocarbon (PAHs) were measured in sediments from 29 sites throughout Taihu Lake in China during 2 seasons to investigate spatiotemporal characteristics and source contributions using a 3-way source apportionment approach to positive matrix factorization (PMF3). Seasonal and spatial variations of levels and toxicity suggested higher individual carcinogenic PAH concentrations and toxic equivalent quantity (TEQ) in the flooding season. Three-way PAHs dataset (PAH species, spatial variability, and seasonal variability) was analyzed by PMF3, and its results were compared with a widely used 2-way model (PMF2). Consistent results were observed: vehicular emission was the most important contributor (67.08% by PMF2 and 61.83% by PMF3 for the flooding season; 54.21% by PMF2 and 52.94% by PMF3 for dry season), followed by coal combustion and wood combustion in both seasons. The PMF-cluster analysis was employed to investigate spatial variability of source contributions. Findings can introduce the 3-way approach to apportion sources of PAHs and other persistent organic pollutants (POPs) in sediments, offering the advantage of accounting for information on 3-way datasets.

  4. Application of a source apportionment model in consideration of volatile organic compounds in an urban stream

    USGS Publications Warehouse

    Asher, W.E.; Luo, W.; Campo, K.W.; Bender, D.A.; Robinson, K.W.; Zogorski, J.S.; Pankow, J.F.

    2007-01-01

    Position-dependent concentrations of trichloroethylene and methyl-tert-butyl ether are considered for a 2.81-km section of the Aberjona River in Massachusetts, USA. This river flows through Woburn and Winchester (Massachusetts, USA), an area that is highly urbanized, has a long history of industrial activities dating to the early 1800s, and has gained national attention because of contamination from chlorinated solvent compounds in Woburn wells G and H. The river study section is in Winchester and begins approximately five stream kilometers downstream from the Woburn wells superfund site. Approximately 300 toxic release sites are documented in the watershed upstream from the terminus of the study section. The inflow to the river study section is considered one source of contamination. Other sources are the atmosphere, a tributary flow, and groundwater flows entering the river; the latter are categorized according to stream zone (1, 2, 3, etc.). Loss processes considered include outflows to groundwater and water-to-atmosphere transfer of volatile compounds. For both trichloroethylene and methyl-rerf-butyl ether, degradation is neglected over the timescale of interest. Source apportionment fractions with assigned values ??inflow, ??1, ??2, ??3, etc. are tracked by a source apportionment model. The strengths of the groundwater and tributary sources serve as fitting parameters when minimizing a reduced least squares statistic between water concentrations measured during a synoptic study in July 2001 versus predictions from the model. The model fits provide strong evidence of substantial unknown groundwater sources of trichloroethylene and methyl-tert-butyl ether amounting to tens of grams per day of trichloroethylene and methyl-tert-butyl ether in the river along the study section. Modeling in a source apportionment manner can be useful to water quality managers allocating limited resources for remediation and source control. ?? 2007 SETAC.

  5. Microbial water pollution: a screening tool for initial catchment-scale assessment and source apportionment.

    PubMed

    Kay, D; Anthony, S; Crowther, J; Chambers, B J; Nicholson, F A; Chadwick, D; Stapleton, C M; Wyer, M D

    2010-11-01

    The European Union Water Framework Directive requires that Management Plans are developed for individual River Basin Districts. From the point of view of faecal indicator organisms (FIOs), there is a critical need for screening tools that can provide a rapid assessment of the likely FIO concentrations and fluxes within catchments under base- and high-flow conditions, and of the balance ('source apportionment') between agriculture- and sewage-derived sources. Accordingly, the present paper reports on: (1) the development of preliminary generic models, using water quality and land cover data from previous UK catchment studies for assessing FIO concentrations, fluxes and source apportionment within catchments during the summer bathing season; (2) the calibration of national land use data, against data previously used in the models; and (3) provisional FIO concentration and source-apportionment assessments for England and Wales. The models clearly highlighted the crucial importance of high-flow conditions for the flux of FIOs within catchments. At high flow, improved grassland (and associated livestock) was the key FIO source; FIO loadings derived from catchments with high proportions of improved grassland were shown to be as high as from urbanized catchments; and in many rural catchments, especially in NW and SW England and Wales, which are important areas of lowland livestock (especially dairy) farming, ≥ 40% of FIOs was assessed to be derived from agricultural sources. In contrast, under base-flow conditions, when there was little or no runoff from agricultural land, urban (i.e. sewerage-related) sources were assessed to dominate, and even in rural areas the majority of FIOs were attributed to urban sources. The results of the study demonstrate the potential of this type of approach, particularly in light of climate change and the likelihood of more high-flow events, in underpinning informed policy development and prioritization of investment.

  6. Fine Particle Sources and Cardiorespiratory Morbidity: An Application of Chemical Mass Balance and Factor Analytical Source-Apportionment Methods

    PubMed Central

    Sarnat, Jeremy A.; Marmur, Amit; Klein, Mitchel; Kim, Eugene; Russell, Armistead G.; Sarnat, Stefanie E.; Mulholland, James A.; Hopke, Philip K.; Tolbert, Paige E.

    2008-01-01

    Background Interest in the health effects of particulate matter (PM) has focused on identifying sources of PM, including biomass burning, power plants, and gasoline and diesel emissions that may be associated with adverse health risks. Few epidemiologic studies, however, have included source-apportionment estimates in their examinations of PM health effects. We analyzed a time-series of chemically speciated PM measurements in Atlanta, Georgia, and conducted an epidemiologic analysis using data from three distinct source-apportionment methods. Objective The key objective of this analysis was to compare epidemiologic findings generated using both factor analysis and mass balance source-apportionment methods. Methods We analyzed data collected between November 1998 and December 2002 using positive-matrix factorization (PMF), modified chemical mass balance (CMB-LGO), and a tracer approach. Emergency department (ED) visits for a combined cardiovascular (CVD) and respiratory disease (RD) group were assessed as end points. We estimated the risk ratio (RR) associated with same day PM concentrations using Poisson generalized linear models. Results There were significant, positive associations between same-day PM2.5 (PM with aero-dynamic diameter ≤ 2.5 μm) concentrations attributed to mobile sources (RR range, 1.018–1.025) and biomass combustion, primarily prescribed forest burning and residential wood combustion, (RR range, 1.024–1.033) source categories and CVD-related ED visits. Associations between the source categories and RD visits were not significant for all models except sulfate-rich secondary PM2.5 (RR range, 1.012–1.020). Generally, the epidemiologic results were robust to the selection of source-apportionment method, with strong agreement between the RR estimates from the PMF and CMB-LGO models, as well as with results from models using single-species tracers as surrogates of the source-apportioned PM2.5 values. Conclusions Despite differences among the

  7. Source apportionment of size resolved particulate matter at a European air pollution hot spot.

    PubMed

    Pokorná, P; Hovorka, J; Klán, M; Hopke, P K

    2015-01-01

    Positive Matrix Factorization-PMF was applied to hourly resolved elemental composition of fine (PM0.15-1.15) and coarse (PM1.15-10) aerosol particles to apportion their sources in the airshed of residential district, Ostrava-Radvanice and Bartovice in winter 2012. Multiple-site measurement by PM2.5 monitors complements the source apportionment. As there were no statistical significant differences amongst the monitors, the source apportionment derived for the central site data is expected to apply to whole residential district. The apportioned sources of the fine aerosol particles were coal combustion (58.6%), sinter production-hot phase (22.9%), traffic (15%), raw iron production (3.5%), and desulfurization slag processing (<0.5%) whilst road dust (47.3%), sinter production-cold phase (27.7%), coal combustion (16.8%), and raw iron production (8.2%) were resolved being sources of the coarse aerosol particles. The shape and elemental composition of size-segregated aerosol airborne-sampled by an airship aloft presumed air pollution sources helped to interpret the PMF solution.

  8. SOURCE APPORTIONMENT OF EXPOSURES TO VOLATILE ORGANIC COMPOUNDS: I. EVALUATION OF RECEPTOR MODELS USING SIMULATED EXPOSURE DATA. (R826788)

    EPA Science Inventory

    Four receptor-oriented source apportionment models were evaluated by applying them to simulated personal exposure data for select volatile organic compounds (VOCs) that were generated by Monte Carlo sampling from known source contributions and profiles. The exposure sources mo...

  9. Fine particulate matter source apportionment using a hybrid chemical transport and receptor model approach

    NASA Astrophysics Data System (ADS)

    Hu, Y.; Balachandran, S.; Pachon, J. E.; Baek, J.; Ivey, C.; Holmes, H.; Odman, M. T.; Mulholland, J. A.; Russell, A. G.

    2013-10-01

    A hybrid fine particulate matter (PM2.5) source apportionment approach based on a receptor-model (RM) species balance and species specific source impacts from a chemical transport model (CTM) equipped with a sensitivity analysis tool is developed to provide physically- and chemically-consistent relationships between source emissions and receptor impacts. This hybrid approach enhances RM results by providing initial estimates of source impacts from a much larger number of sources than are typically used in RMs, and provides source-receptor relationships for secondary species. Further, the method addresses issues of source collinearities, and accounts for emissions uncertainties. Hybrid method results also provide information on the resulting source impact uncertainties. We apply this hybrid approach to conduct PM2.5 source apportionment at Chemical Speciation Network (CSN) sites across the US. Ambient PM2.5 concentrations at these receptor sites were apportioned to 33 separate sources. Hybrid method results led to large changes of impacts from CTM estimates for sources such as dust, woodstove, and other biomass burning sources, but limited changes to others. The refinements reduced the differences between CTM-simulated and observed concentrations of individual PM2.5 species by over 98% when using a weighted least squared error minimization. The rankings of source impacts changed from the initial estimates, revealing that CTM-only results should be evaluated with observations. Assessment with RM results at six US locations showed that the hybrid results differ somewhat from commonly resolved sources. The hybrid method also resolved sources that typical RM methods do not capture without extra measurement information on unique tracers. The method can be readily applied to large domains and long (such as multi-annual) time periods to provide source impact estimates for management- and health-related studies.

  10. Fine particulate matter source apportionment using a hybrid chemical transport and receptor model approach

    NASA Astrophysics Data System (ADS)

    Hu, Y.; Balachandran, S.; Pachon, J. E.; Baek, J.; Ivey, C.; Holmes, H.; Odman, M. T.; Mulholland, J. A.; Russell, A. G.

    2014-06-01

    A hybrid fine particulate matter (PM2.5) source apportionment approach based on a receptor model (RM) species balance and species specific source impacts from a chemical transport model (CTM) equipped with a sensitivity analysis tool is developed to provide physically and chemically consistent relationships between source emissions and receptor impacts. This hybrid approach enhances RM results by providing initial estimates of source impacts from a much larger number of sources than are typically used in RMs, and provides source-receptor relationships for secondary species. Further, the method addresses issues of source collinearities and accounts for emissions uncertainties. We apply this hybrid approach to conduct PM2.5 source apportionment at Chemical Speciation Network (CSN) sites across the US. Ambient PM2.5 concentrations at these receptor sites were apportioned to 33 separate sources. Hybrid method results led to large changes of impacts from CTM estimates for sources such as dust, woodstoves, and other biomass-burning sources, but limited changes to others. The refinements reduced the differences between CTM-simulated and observed concentrations of individual PM2.5 species by over 98% when using a weighted least-squares error minimization. The rankings of source impacts changed from the initial estimates, further demonstrating that CTM-only results should be evaluated with observations. Assessment with RM results at six US locations showed that the hybrid results differ somewhat from commonly resolved sources. The hybrid method also resolved sources that typical RM methods do not capture without extra measurement information for unique tracers. The method can be readily applied to large domains and long (such as multi-annual) time periods to provide source impact estimates for management- and health-related studies.

  11. Source apportionment of particulate matter in a large city of southeastern Po Valley (Bologna, Italy).

    PubMed

    Tositti, L; Brattich, E; Masiol, M; Baldacci, D; Ceccato, D; Parmeggiani, S; Stracquadanio, M; Zappoli, S

    2014-01-01

    This study reports the results of an experimental research project carried out in Bologna, a midsize town in central Po valley, with the aim at characterizing local aerosol chemistry and tracking the main source emissions of airborne particulate matter. Chemical speciation based upon ions, trace elements, and carbonaceous matter is discussed on the basis of seasonal variation and enrichment factors. For the first time, source apportionment was achieved at this location using two widely used receptor models (principal component analysis/multi-linear regression analysis (PCA/MLRA) and positive matrix factorization (PMF)). Four main aerosol sources were identified by PCA/MLRA and interpreted as: resuspended particulate and a pseudo-marine factor (winter street management), both related to the coarse fraction, plus mixed combustions and secondary aerosol largely associated to traffic and long-lived species typical of the fine fraction. The PMF model resolved six main aerosol sources, interpreted as: mineral dust, road dust, traffic, secondary aerosol, biomass burning and again a pseudo-marine factor. Source apportionment results from both models are in good agreement providing a 30 and a 33% by weight respectively for PCA-MLRA and PMF for the coarse fraction and 70% (PCA-MLRA) and 67% (PMF) for the fine fraction. The episodic influence of Saharan dust transport on PM10 exceedances in Bologna was identified and discussed in term of meteorological framework, composition, and quantitative contribution.

  12. RECENT APPLICATIONS OF SOURCE APPORTIONMENT METHODS AND RELATED NEEDS

    EPA Science Inventory

    Traditional receptor modeling studies have utilized factor analysis (like principal component analysis, PCA) and/or Chemical Mass Balance (CMB) to assess source influences. The limitations with these approaches is that PCA is qualitative and CMB requires the input of source pr...

  13. Source apportionment: findings from the US supersites program

    SciTech Connect

    John G. Watson; L.-W. Antony Chen; Judith C. Chow; Prakash Doraiswamy; Douglas H. Lowenthal

    2008-02-15

    Receptor models are used to identify and quantify source contributions to particulate matter and volatile organic compounds based on measurements of many chemical components at receptor sites. These components are selected based on their consistent appearance in some source types and their absence in others. UNMIX, positive matrix factorization (PMF), and effective variance are different solutions to the chemical mass balance (CMB) receptor model equations and are implemented on available software. In their more general form, the CMB equations allow spatial, temporal, transport, and particle size profiles to be combined with chemical source profiles for improved source resolution. Although UNMIX and PMF do not use source profiles explicitly as input data, they still require measured profiles to justify their derived source factors. The U.S. Supersites Program provided advanced datasets to apply these CMB solutions in different urban areas. Still lacking are better characterization of source emissions, new methods to estimate profile changes between source and receptor, and systematic sensitivity tests of deviations from receptor model assumptions. 154 refs.

  14. Analyzing hydrocarbons in sewer to help in PAH source apportionment in sewage sludges.

    PubMed

    Mansuy-Huault, Laurence; Regier, Annette; Faure, Pierre

    2009-05-01

    A multi-molecular approach for polycyclic aromatic hydrocarbons (PAH) source apportionment in sewage sludge was tested. Three simple catchment areas with corresponding wastewater treatment plants (WWTP) were chosen. Sewage sludges of these WWTPs chronically exceeded the French guide values for PAHs. Aliphatic and aromatic hydrocarbons were quantified in sediments or wastewater suspended particulate matter sampled in different locations of the sewer as well as in sewage sludge. Various molecular indices including PAH ratios were calculated. The results showed that the ratios calculated from sewage sludge analyses provided a rather unspecific hydrocarbon fingerprint where combustion input appear as the main PAH sources. The complexity of the inputs as well as degradation occurring during wastewater treatment prevent any detailed diagnosis. Coupled to the analyses of samples collected in the sewer, the multi-molecular approach becomes more efficient especially for the identification of specific petroleum inputs such as fuel or used lubricating oils which can be important PAH sources. Indeed, the sampling in the sewer allows a spatial screening of the hydrocarbon inputs and facilitates the PAH source apportionment by avoiding the dilution of specific inputs with the whole wastewater inputs and by limiting the degradation of the molecular fingerprint that could occur during transfer and treatment in the WWTP. Then, the combination of PAH ratios and aliphatic distribution analyses is a very valuable approach that can help in sewer and WWTP management.

  15. Toxicity evaluation and source apportionment of Polycyclic Aromatic Hydrocarbons (PAHs) at three stations in Istanbul, Turkey.

    PubMed

    Hanedar, Asude; Alp, Kadir; Kaynak, Burçak; Avşar, Edip

    2014-08-01

    This paper focuses on the toxicity evaluation and source apportionment of Polycyclic Aromatic Hydrocarbons (PAHs) in three monitoring stations in Istanbul, Turkey. A total of 326 airborne samples were collected and analyzed for 16 PAHs and Total Suspended Particles (TSP) for the period of September 2006-December 2007. The total average PAH concentrations were 100.7±61.3, 84.6±46.7 and 25.1±13.3 ng m(-3) and the TSP concentrations were 101.2±53.2, 152.3±99.1, 49.8±18.6 μg m(-3) for URB1, URB2 and RUR stations, respectively. Benzo(a)Pyren (BaP) toxic equivalency factors to PAH concentration values were calculated indicating that the health risk of BaP and DiBenz(a,h)Anthracene (markers of traffic emissions) have the highest contribution compared to all of the other species measured at the sampling sites. In order to determine PAH sources, two different source apportionment techniques were applied to the measurements; diagnostic ratios (DR) and Positive Matrix Factorization (PMF). The results of the two applications were compatible indicating the vehicle emissions - especially diesel engines - as the major source for urban stations.

  16. Source apportionment of PM2.5 in Incheon, Korea

    NASA Astrophysics Data System (ADS)

    Choi, J.; Ban, S.; Lee, C.; Yi, S.; Zoh, K.

    2011-12-01

    PM2.5 samples were collected at a centrally located urban monitoring site in Incheon, Korea, every third day from Jun 2009 to may 2010 and analyzed their chemical species. In this study, we investigated the source of PM2.5 using Positive Matrix Factorization(PMF), the source area from Potential Source Contribution Function (PSCF) and Conditional Probability Function(CPF), and characterized source variation among episode, non-episode, yellow sand events. Incheon, study site, is located at the mid-western tip of the Korean Peninsula with a population of 2.6 million people and area of 1029.4 km2, respectively. As a transportation hub, the city also holds the importance of meteological/geological aspect affecting the air quality of capital region, in that is prevailing westerlies zone and a air passageway from China to Japan passing through seoul, korea. In the study, the Four channel based on Annular Denuder System(ADS) were used for sample collection(URG co, USA). The filter samples were analyzed with respect to species type such as ion group, metal, and OC/EC compound using ion chromatography, ICP/MS, and NIOSH TOT method, respectively. The PM2.5 concentration was 43ug/m3 that is almost three times higher than the US NAAQS annual PM2.5 standard of 15ug/m3. Nine PM2.5 sources were resolved from PMF analysis that provided reasonable source profiles and interesting insights into the source contributions to the ambient mass concentrations. The major sources of PM2.5 were secondary nitrate(26.4%), secondary sulfate(17.3%), gasoline(16.4%), and residual oil combustion(13.5%), with lesser contributions from biomass burning (7.5%), road dust(6.9%), soil (5.5%), coal fire powerplant (4.0%), and free sea salt(2.4%). CPF results identified possible local source directions such as motor vehicles, free sea salt. PSCF results indicated that likely pollution areas increased secondary particle concentrations(sulfate and nitrate) in Incheon to be the major industrial areas in China

  17. Source apportionment of fine particles in Kuwait City.

    PubMed

    Alolayan, Mohammad A; Brown, Kathleen W; Evans, John S; Bouhamra, Walid S; Koutrakis, Petros

    2013-03-15

    This study investigated major sources of PM2.5 in the atmosphere of Kuwait based on a sampling program conducted between February 2004 and October 2005. Three source identification techniques were used in this study: (1) a positive matrix factorization model; (2) backward trajectory profiles; and (3) concentration rose plots. Five major sources of PM2.5 were estimated. These were sand dust (sand storms), oil combustion (power plants), petrochemical industry (fertilizer, nylon or catalyst regeneration facilities), traffic (vehicle emissions and road dust) and transported emissions (emissions from outside Kuwait, such as those from automobiles, road dust or smelters). The estimated contributions to PM2.5 of these sources were: 54% from sand dust, 18% from oil combustion, 12% from petrochemical industry, 11% from traffic and 5% from anthropogenic sources transported from outside the country. Oil combustion, petrochemical industry and traffic were found to emanate from local sources, whereas sand dust and some emissions from traffic, and possibly smelters, appeared to originate from sources outside of Kuwait (transported). The PM2.5 levels in Kuwait during our previous sampling study averaged 53μg/m(3). More than half of the measured PM2.5 appears to have been due to crustal material, much originating outside of the country. However, the relatively high levels of PM2.5 contributed by anthropogenic local sources, such as oil combustion, petrochemical industry emissions, and traffic indicated that there may be great opportunities for Kuwait to improve public health. The application of cost-effective emission controls and development of forward looking environmental health policies have the potential to significantly reduce emissions, population exposures to PM2.5 and the burden of mortality and morbidity from air pollution.

  18. Atmospheric polycyclic aromatic hydrocarbons in the urban environment: Occurrence, toxicity and source apportionment.

    PubMed

    Mishra, Nitika; Ayoko, Godwin A; Morawska, Lidia

    2016-01-01

    Polycyclic Aromatic Hydrocarbons (PAHs) represent a major class of toxic pollutants because of their carcinogenic and mutagenic characteristics. People living in urban areas are regularly exposed to PAHs because of abundance of their emission sources. Within this context, this study aimed to: (i) identify and quantify the levels of ambient PAHs in an urban environment; (ii) evaluate their toxicity; and (iii) identify their sources as well as the contribution of specific sources to measured concentrations. Sixteen PAHs were identified and quantified in air samples collected from Brisbane. Principal Component Analysis - Absolute Principal Component Scores (PCA-APCS) was used in order to conduct source apportionment of the measured PAHs. Vehicular emissions, natural gas combustion, petrol emissions and evaporative/unburned fuel were the sources identified; contributing 56%, 21%, 15% and 8% of the total PAHs emissions, respectively, all of which need to be considered for any pollution control measures implemented in urban areas.

  19. Source apportionment of exposures to volatile organic compounds: II. Application of receptor models to TEAM study data

    NASA Astrophysics Data System (ADS)

    Anderson, Melissa J.; Daly, Eileen P.; Miller, Shelly L.; Milford, Jana B.

    Four receptor-oriented source apportionment models were applied to personal exposure measurements for toxic volatile organic compounds (VOCs). The measurements are from the total exposure assessment methodology studies conducted from 1980 to 1984 in New Jersey (NJ) and California (CA) and the 1987-1990 CA Indoor Exposure study. The receptor models applied are the Chemical Mass Balance model, Principal Component Analysis/Absolute Principal Component Scores, Positive Matrix Factorization, and Graphical Ratio Analysis for Composition Estimates/Source Apportionment by Factors with Explicit Restriction. Major sources of personal exposure to toxic VOCs appear to have been aromatic sources resembling automobile exhaust, gasoline vapor, or environmental tobacco smoke, and a 1,1,1-trichloroethane-dominated source that may be associated with solvent or pesticide use. Drycleaning chemicals, deodorizers or mothballs, and building materials or carpet emissions also appear to have been significant sources of exposure. Source apportionment results from the four models agreed reasonably well for the NJ data. The performance of the models was generally poorer for the CA data, and the corresponding source apportionment results were less consistent across the models.

  20. Heavy metal contamination status and source apportionment in sediments of Songhua River Harbin region, Northeast China.

    PubMed

    Li, Ning; Tian, Yu; Zhang, Jun; Zuo, Wei; Zhan, Wei; Zhang, Jian

    2016-07-09

    The Songhua River represents one of the seven major river systems in China. It flows through Harbin city with 66 km long, locating in the northern China with a longer winter time. This paper aimed to study concentration distributions, stability, risk assessment, and source apportionment of heavy metals including chromium (Cr), cadmium (Cd), lead (Pb), mercury (Hg), arsenic (As), copper (Cu), zinc (Zn), and nickel (Ni) in 11 selected sections of the Songhua River Harbin region. Results showed that Cr, Cd, Pb, Hg, and As exceeded their respective geochemical background values in sediments of most monitoring sections. Compared with other important rivers and lakes in China, Cr, Hg, Cd, and As pollutions in surface sediments were above medium level. Further analysis of chemical speciation indicated that Cr and As in surface sediments were relatively stable while Pb and Cd were easily bioavailable. Correlation analysis revealed sources of these metals except As might be identical. Pollution levels and ecological risks of heavy metals in surface sediments presented higher in the mainstream region (45° 47.0' N ~ 45° 53.3' N, 126° 37.0' E ~ 126° 42.1' E). Source apportionment found Hejiagou and Ashi River were the main contributors to metal pollution of this region. Thus, anthropogenic activities along the Hejiagou and Ashi River should be restricted in order to protect the Songhua River Harbin region from metal contamination.

  1. Ultrafine particles: exposure and source apportionment in 56 Danish homes.

    PubMed

    Bekö, Gabriel; Weschler, Charles J; Wierzbicka, Aneta; Karottki, Dorina Gabriela; Toftum, Jørn; Loft, Steffen; Clausen, Geo

    2013-09-17

    Particle number (PN) concentrations (10-300 nm in size) were continuously measured over a period of ~45 h in 56 residences of nonsmokers in Copenhagen, Denmark. The highest concentrations were measured when occupants were present and awake (geometric mean, GM: 22.3 × 10(3) cm(-3)), the lowest when the homes were vacant (GM: 6.1 × 10(3) cm(-3)) or the occupants were asleep (GM: 5.1 × 10(3) cm(-3)). Diary entries regarding occupancy and particle related activities were used to identify source events and apportion the daily integrated exposure among sources. Source events clearly resulted in increased PN concentrations and decreased average particle diameter. For a given event, elevated particle concentrations persisted for several hours after the emission of fresh particles ceased. The residential daily integrated PN exposure in the 56 homes ranged between 37 × 10(3) and 6.0 × 10(6) particles per cm(3)·h/day (GM: 3.3 × 10(5) cm(-3)·h/day). On average, ~90% of this exposure occurred outside of the period from midnight to 6 a.m. Source events, especially candle burning, cooking, toasting, and unknown activities, were responsible on average for ~65% of the residential integrated exposure (51% without the unknown activities). Candle burning occurred in half of the homes where, on average, it was responsible for almost 60% of the integrated exposure.

  2. Relevance of aerosol size spectrum analysis as support to qualitative source apportionment studies.

    PubMed

    Manigrasso, M; Febo, A; Guglielmi, F; Ciambottini, V; Avino, P

    2012-11-01

    This work presents a diagnostic methodology in support to source apportionment studies to identify remote and local pollution sources. It is based on the temporal analysis of both PM size distributions and PM size fraction correlation along with natural radioactivity measurements as index of Planetary Boundary Layer dynamic. A correlation drop is indicative of changing aerosol sources. When this observation is coupled with decreasing level of natural radioactivity and increasing aerosol concentration, be it coarse or fine, it is indicative of the inflow of remote polluted air masses. The methodology defines in which size range operates the contribution of remote pollution sources. It was applied to two PM10 pollution episodes: the first involved the advection of coarse PM, the second entailed the inflow of two air masses, one transporting coarse dust and the other fine PM. Dust models and backward trajectories analysis confirmed such results, indicating the air mass provenience.

  3. Secondary organic aerosol formation and source apportionment in Southeast Texas

    NASA Astrophysics Data System (ADS)

    Zhang, Hongliang; Ying, Qi

    2011-06-01

    The latest version of US EPA's Community Multi-scale Air Quality (CMAQ v4.7) model with the most recent update on secondary organic aerosol (SOA) formation pathways was adapted into a source-oriented modeling framework to determine the contributions of different emission sources to SOA concentrations from a carbon source perspective in Southeast Texas during the 2000 Texas Air Quality Study (TexAQS 2000) from August 25 to September 5, 2000. A comparison of the VOC and SOA predictions with observations shows that anthropogenic emissions of long chain alkanes and aromatics are likely underestimated in the EPA's Clean Air Interstate Rule (CAIR) inventory and the current SOA mechanism in CMAQ still under-predicts SOA. The peak SOA concentrations measured at La Porte are more accurately predicted by increasing the emissions of the anthropogenic SOA precursors by a factor of 5 although the overall precursor concentrations are better predicted by increasing the emissions by a factor of 2. A linear correlation between SOA and odd oxygen (ΔSOA/ΔOx = 23.0-28.4 μg m-3/ppm Ox) can be found when they are formed simultaneously in the air masses passing the urban Houston area on high SOA days. Based on the adjusted emissions (a factor of 2 increase in the alkane and aromatics precursor emissions), approximately 20% of the total SOA in the Houston-Galveston Bay area is due to anthropogenic sources. Solvent utilization and gasoline engines are the main anthropogenic sources. SOA from alkanes and aromatics accounts for approximately 2-4% and 5-9% of total SOA, respectively. The predicted overall anthropogenic SOA concentrations are not sensitive to the half-life time used to calculate the conversion rate of semi-volatile organic compounds to non-volatile oligomers in the particle phase. The main precursors of biogenic SOA are sesquiterpenes, which contribute to approximately 12-35% of total SOA. Monoterpenes contribute to 3-14% and isoprene accounts for approximately 6-9% of the

  4. Source apportionment studies on particulate matter in Beijing/China

    NASA Astrophysics Data System (ADS)

    Suppan, P.; Shen, R.; Shao, L.; Schrader, S.; Schäfer, K.; Norra, S.; Vogel, B.; Cen, K.; Wang, Y.

    2013-05-01

    More than 15 million people in the greater area of Beijing are still suffering from severe air pollution levels caused by sources within the city itself but also from external impacts like severe dust storms and long range advection from the southern and central part of China. Within this context particulate matter (PM) is the major air pollutant in the greater area of Beijing (Garland et al., 2009). PM did not serve only as lead substance for air quality levels and therefore for adverse health impact effects but also for a strong influence on the climate system by changing e.g. the radiative balance. Investigations on emission reductions during the Olympic Summer Games in 2008 have caused a strong reduction on coarser particles (PM10) but not on smaller particles (PM2.5). In order to discriminate the composition of the particulate matter levels, the different behavior of coarser and smaller particles investigations on source attribution, particle characteristics and external impacts on the PM levels of the city of Beijing by measurements and modeling are performed: a) Examples of long term measurements of PM2.5 filter sampling in 2010/2011 with the objectives of detailed chemical (source attribution, carbon fraction, organic speciation and inorganic composition) and isotopic analyses as well as toxicological assessment in cooperation with several institutions (Karlsruhe Institute of Technology (IfGG/IMG), Helmholtz Zentrum München (HMGU), University Rostock (UR), Chinese University of Mining and Technology Beijing, CUMTB) will be discussed. b) The impact of dust storm events on the overall pollution level of particulate matter in the greater area of Beijing is being assessed by the online coupled comprehensive model system COSMO-ART. First results of the dust storm modeling in northern China (2011, April 30th) demonstrates very well the general behavior of the meteorological parameters temperature and humidity as well as a good agreement between modeled and

  5. Source apportionment of atmospheric PAHs in the western Balkans by natural abundance radiocarbon analysis.

    PubMed

    Zencak, Zdenek; Klanova, Jana; Holoubek, Ivan; Gustafsson, Orjan

    2007-06-01

    Progress in source apportionment of priority combustion-derived atmospheric pollutants can be made by an inverse approach to inventory emissions, namely, receptor-based compound class-specific radiocarbon analysis (CCSRA) of target pollutants. In the present study, CCSRA of the combustion-derived polycyclic aromatic hydrocarbons (PAHs) present in the atmosphere of the countries of the former republic of Yugoslavia was performed. The carbon stable isotope composition (delta13C) of PAHs varied between -27.68 and -27.19 per thousand, whereas delta14C values ranged from -568 per thousand for PAHs sampled in Kosovo to -288 per thousand for PAHs sampled in the Sarajevo area. The application of an isotopic mass balance model to these delta14C data revealed a significant contribution (35-65%) from the combustion of non-fossil material to the atmospheric PAH pollution, even in urban and industrialized areas. Furthermore, consistency was observed between the isotopic composition of PAHs obtained by high-volume sampling and those collected by passive sampling. This encourages the use of passive samplers for CCSRA applications. This marks the first time that a CCSRA investigation could be executed on a geographically wide scale, providing a quantitative field-based source apportionment, which points out that also non-fossil combustion processes should be targeted for remedial action.

  6. Source apportionment of atmospheric PAHs in the Western Balkans by natural abundance radiocarbon analysis

    SciTech Connect

    Zdenek Zencak; Jana Klanova; Ivan Holoubek; Oerjan Gustafsson

    2007-06-01

    Progress in source apportionment of priority combustion-derived atmospheric pollutants can be made by an inverse approach to inventory emissions, namely, receptor-based compound class-specific radiocarbon analysis (CCSRA) of target pollutants. In the present study, CCSRA of the combustion-derived polycyclic aromatic hydrocarbons (PAHs) present in the atmosphere of the countries of the former republic of Yugoslavia was performed. The carbon stable isotope composition ({delta}{sup 13}C) of PAHs varied between -27.68 and -27.19{per_thousand}, whereas {Delta}{sup 14}C values ranged from -568{per_thousand} for PAHs sampled in Kosovo to -288{per_thousand} for PAHs sampled in the Sarajevo area. The application of an isotopic mass balance model to these {Delta}{sup 14}C data revealed a significant contribution (35-65%) from the combustion of non-fossil material to the atmospheric PAH pollution, even in urban and industrialized areas. Furthermore, consistency was observed between the isotopic composition of PAHs obtained by high-volume sampling and those collected by passive sampling. This encourages the use of passive samplers for CCSRA applications. This marks the first time that a CCSRA investigation could be executed on a geographically wide scale, providing a quantitative field-based source apportionment, which points out that also non-fossil combustion processes should be targeted for remedial action. 36 refs., 1 fig., 3 tabs.

  7. Contamination characteristics and source apportionment of trace metals in soils around Miyun Reservoir.

    PubMed

    Chen, Haiyang; Teng, Yanguo; Chen, Ruihui; Li, Jiao; Wang, Jinsheng

    2016-08-01

    Due to their toxicity and bioaccumulation, trace metals in soils can result in a wide range of toxic effects on animals, plants, microbes, and even humans. Recognizing the contamination characteristics of soil metals and especially apportioning their potential sources are the necessary preconditions for pollution prevention and control. Over the past decades, several receptor models have been developed for source apportionment. Among them, positive matrix factorization (PMF) has gained popularity and was recommended by the US Environmental Protection Agency as a general modeling tool. In this study, an extended chemometrics model, multivariate curve resolution-alternating least squares based on maximum likelihood principal component analysis (MCR-ALS/MLPCA), was proposed for source apportionment of soil metals and applied to identify the potential sources of trace metals in soils around Miyun Reservoir. Similar to PMF, the MCR-ALS/MLPCA model can incorporate measurement error information and non-negativity constraints in its calculation procedures. Model validation with synthetic dataset suggested that the MCR-ALS/MLPCA could extract acceptable recovered source profiles even considering relatively larger error levels. When applying to identify the sources of trace metals in soils around Miyun Reservoir, the MCR-ALS/MLPCA model obtained the highly similar profiles with PMF. On the other hand, the assessment results of contamination status showed that the soils around reservoir were polluted by trace metals in slightly moderate degree but potentially posed acceptable risks to the public. Mining activities, fertilizers and agrochemicals, and atmospheric deposition were identified as the potential anthropogenic sources with contributions of 24.8, 14.6, and 13.3 %, respectively. In order to protect the drinking water source of Beijing, special attention should be paid to the metal inputs to soils from mining and agricultural activities.

  8. Fine Particulate Pollution and Source Apportionment in the Urban Centers for Africa, Asia and Latin America

    NASA Astrophysics Data System (ADS)

    Guttikunda, S. K.; Johnson, T. M.; Procee, P.

    2004-12-01

    Fossil fuel combustion for domestic cooking and heating, power generation, industrial processes, and motor vehicles are the primary sources of air pollution in the developing country cities. Over the past twenty years, major advances have been made in understanding the social and economic consequences of air pollution. In both industrialized and developing countries, it has been shown that air pollution from energy combustion has detrimental impacts on human health and the environment. Lack of information on the sectoral contributions to air pollution - especially fine particulates, is one of the typical constraints for an effective integrated urban air quality management program. Without such information, it is difficult, if not impossible, for decision makers to provide policy advice and make informed investment decisions related to air quality improvements in developing countries. This also raises the need for low-cost ways of determining the principal sources of fine PM for a proper planning and decision making. The project objective is to develop and verify a methodology to assess and monitor the sources of PM, using a combination of ground-based monitoring and source apportionment techniques. This presentation will focus on four general tasks: (1) Review of the science and current activities in the combined use of monitoring data and modeling for better understanding of PM pollution. (2) Review of recent advances in atmospheric source apportionment techniques (e.g., principal component analysis, organic markers, source-receptor modeling techniques). (3) Develop a general methodology to use integrated top-down and bottom-up datasets. (4) Review of a series of current case studies from Africa, Asia and Latin America and the methodologies applied to assess the air pollution and its sources.

  9. A novel approach for apportionment between primary and secondary sources of airborne nitrated polycyclic aromatic hydrocarbons (NPAHs)

    NASA Astrophysics Data System (ADS)

    Lin, Yan; Qiu, Xinghua; Ma, Yiqiu; Wang, Junxia; Wu, Yusheng; Zeng, Limin; Hu, Min; Zhu, Tong; Zhu, Yifang

    2016-08-01

    Nitrated polycyclic aromatic hydrocarbons (NPAHs) are strong environmental mutagens and carcinogens originating from both primary emissions and secondary reactions in the atmosphere. The sources and the toxicity of different NPAH species could vary greatly; therefore a specie-specific source apportionment is essential to evaluate their health risks and to formulate controlling regulations. However, few studies have reported source apportionment of NPAHs species to date. In this study, we developed an easy-to-perform method for the apportionment of primary versus secondary sources of airborne NPAHs based on the relationship between NPAHs and NO2. After log-transformation of both NPAHs and NO2 concentrations, a slope of β between these two variables was obtained by the linear regression. When β is significantly smaller than 1, it indicates primary emissions while β significantly greater than 1 suggests secondary formation. We have validated this method with data previously collected in Beijing. A good correlation, with R value of 0.57, was observed between results produced by this new method and by Positive Matrix Factorization (PMF). The correlation could be further improved (R = 0.71) if the gas/particle partition of NPAHs is taken into consideration. This developed method enables the source apportionment for individual NPAHs species and could be used to validate the results of other receptor models.

  10. The Analysis of PM2.5 Source Apportionment Technique's Competitiveness in China

    NASA Astrophysics Data System (ADS)

    Qian, K.; Deng, L.; An, Y. B.; Liu, S. Y.; Hao, H. Z.

    Nowadays, people has paid more attention to PM2.5 in various countries of the world. PM2.5 is a kind of particulate matter whose diameter less than 2.5μm, with great damage to environment and public's health. The origin of source apportionment technique is studies of atmospheric particulate matter, it uses two mathematical models, one of them is diffusion model which study the source of pollution, and another one called receptor model which study the pollution of area. In my study, I will analyze the competitiveness of similar technology in various countries by using microscope to analyze shape characteristic, Enrichment Factor Method (EF), Factor Analyze Method (FA), EPA-CMB8.2 Model, combining with the consequence of Improved-source-analysis Technology and Orthogonal matrix decomposition Model.

  11. Comparison of multi-receptor and single-receptor trajectory source apportionment (TSA) methods using artificial sources

    NASA Astrophysics Data System (ADS)

    Lee, Stephanie; Ashbaugh, Lowell

    Two trajectory source apportionment methods were tested using an artificially generated data set to determine their ability to detect the known sources. The residence time or conditional probability method developed by Ashbaugh et al. [1985. A residence time probability analysis of sulfur concentrations at Grand Canyon National Park. Atmospheric Environment 19(8), 1263-1270] uses a single receptor at a time, whereas the new multi-receptor (MURA) method developed here uses several receptors at once in an attempt to detect the sources with higher accuracy. The methods were first tested using a simulation with a single source and then with another simulation using four sources. The ability of the methods to detect the sources was quantified for each simulation. The MURA trajectory method proved to be superior at identifying sources for these simulations.

  12. Source apportionment of ambient VOCS in Mumbai city

    NASA Astrophysics Data System (ADS)

    Srivastava, Anjali

    Air pollution kills almost half a million Asians every year. Most of this pollution is emitted from buses, trucks, motorcycles and other forms of transport. As Asia's cities continue to expand, the rising number of vehicles has resulted in even greater pollution. Amongst the measures available to control, vehicular emission was engine modification, catalytic converters and fuel modifications. Some of these have led to emissions of some hazardous air pollutants (HAP) like volatile organic compounds (VOCs). VOC emission is an area needing attention in air quality management. This paper discusses a study on VOC concentration at major sources like traffic junction, residential area, commercial areas, industrial areas and petrol pumps in Mumbai city. CMB8 Model has been used to apportion VOCs in Mumbai city. It was observed that evaporative emissions dominate in Mumbai. In order to control VOCs in air the management strategy should thus focus on cost effective vapor recovery systems at refueling stations and in vehicles. Effective inspection and maintenance programme can reduce evaporative and exhaust VOC emissions. Modifying certain fuel parameters, like reducing benzene content in petrol will as well reduce VOC content in air. The benzene content in petrol was 3% in the year 2001 in Mumbai. Adulteration also results in high levels of VOCs in air.

  13. Source apportionment of gaseous and particulate PAHs from traffic emission using tunnel measurements in Shanghai, China

    NASA Astrophysics Data System (ADS)

    Liu, Ying; Wang, Siyao; Lohmann, Rainer; Yu, Na; Zhang, Chenkai; Gao, Yi; Zhao, Jianfu; Ma, Limin

    2015-04-01

    Understanding sources and contributions of gaseous and particulate PAHs from traffic-related pollution can provide valuable information for alleviating air contamination from traffic in urban areas. On-road sampling campaigns were comprehensively conducted during 2011-2012 in an urban tunnel of Shanghai, China. 2-3 rings PAHs were abundant in the tunnel's gas and particle phases. Diagnostic ratios of PAHs were statistically described; several were significantly different between the gas and particle phases. Principal component analysis (PCA), positive matrix factorization (PMF), bivariate correlation analysis and multiple linear regression analysis (MLRA) were applied to apportion sources of gaseous and particulate PAHs in the tunnel. Main sources of the gaseous PAHs included evaporative emission of fuel, high-temperature and low-temperature combustion of fuel, accounting for 50-51%, 30-36% and 13-20%, respectively. Unburned fuel particles (56.4-78.3%), high-temperature combustion of fuel (9.5-26.1%) and gas-to-particle condensation (12.2-17.5%) were major contributors to the particulate PAHs. The result reflected, to a large extent, PAH emissions from the urban traffic of Shanghai. Improving fuel efficiency of local vehicles will greatly reduce contribution of traffic emission to atmospheric PAHs in urban areas. Source apportionment of PM10 mass was also performed based on the organic component data. The results showed that high-temperature combustion of fuel and gas-to-particle condensation contributed to 15-18% and 7-8% of PM10 mass, respectively, but 55-57% of the particle mass was left unexplained. Although the results from the PCA and PMF models were comparable, the PMF method is recommended for source apportionment of PAHs in real traffic conditions. In addition, the combination of multivariate statistical method and bivariate correlation analysis is a useful tool to comprehensively assess sources of PAHs.

  14. An integrated PM2.5 source apportionment study: Positive Matrix Factorisation vs. the chemical transport model CAMx

    NASA Astrophysics Data System (ADS)

    Bove, M. C.; Brotto, P.; Cassola, F.; Cuccia, E.; Massabò, D.; Mazzino, A.; Piazzalunga, A.; Prati, P.

    2014-09-01

    Receptor and Chemical Transport Models are commonly used tools in source apportionment studies, even if different expertise is required. We describe an experiment using both approaches to apportion the PM2.5 (i.e., particulate matter with aerodynamic diameters below 2.5 μm) sources in the city of Genoa (Italy). A sampling campaign was carried out to collect PM2.5 samples daily for approximately six month during 2011 in three sites. The subsequent compositional analyses included the speciation of elements, major ions and both organic and elemental carbon; these data produced a large database for receptor modelling through Positive Matrix Factorisation (PMF). In the same period, a meteorological and air quality modelling system was implemented based on the mesoscale numerical weather prediction model WRF and the chemical transport model CAMx to obtain meteorological and pollutant concentrations up to a resolution of 1.1 km. The source apportionment was evaluated by CAMx over the same period that was used for the monitoring campaign using the Particulate Source Apportionment Technology tool. Even if the source categorisations were changed (i.e., groups of time-correlated compounds in PMF vs. activity categories in CAMx), the PM2.5 source apportionment by PMF and CAMx produced comparable results. The different information provided by the two approaches (e.g., real-world factor profile by PMF and apportionment of a secondary aerosol by CAMx) was used jointly to elucidate the composition and origin of PM2.5 and to develop a more general methodology. When studying the primary and secondary components of PM, the main anthropogenic sources in the area were road transportation, energy production/industry and maritime emissions, accounting for 40%-50%, 20%-30% and 10%-15%, of PM2.5, respectively.

  15. Sensitivity and bias of molecular marker-based aerosol source apportionment models to small conltibutions of coal combustion soot.

    PubMed

    Rutter, Andrew P; Snyder, David C; Schauer, James J; DeMinter, Jeff; Shelton, Brandon

    2009-10-15

    Carbonaceous atmospheric particulate matter (PM25) collected in the midwestern United States revealed that soot emissions from incomplete coal combustion were important sources of several organic molecular markers used in source apportionment studies. Despite not constituting a major source of organic carbon in the PM25, coal soot was an important source of polyaromatic hydrocarbons, hopanes, and elemental carbon. These marker compounds are becoming widely used for source apportionment of atmospheric organic PM, meaning that significant emissions of these marker compounds from unaccounted sources such as coal soot could bias apportionment results. This concept was demonstrated using measurements of atmospheric PM collected on a 1-in-6 day schedule at three monitoring sites in Ohio: Mingo Junction (near Steubenville), Cincinnati, and Cleveland. Impacts of coal sootwere measured to be significant at Mingo Junction and small at Cleveland and Cincinnati. As a result, biases in apportionment results were substantial at Mingo Junction and insignificant at Cleveland and Cincinnati. Misapportionments of organic carbon mass at Mingo Junction were significant when coal soot was detected in the particulate samples as identified bythe presence of picene, but when coal soot was not included in the model: gasoline engines (+8% to +58% of OC), smoking engines (0% to -17% of OC), biomass combustion (+1% to +11% of OC), diesel engines (-1% to -2% of OC), natural gas combustion (0% to -2% of OC), and unapportioned OC (0% to -47% of OC). These results suggest that the role of coal soot in source apportionment studies needs to be better examined in many parts of the United States and other parts of the world.

  16. SOURCE APPORTIONMENT OF PM 2.5 AND CARBON IN SEATTLE USING CHEMICAL MASS BALANCE AND POSITIVE MATRIX FACTORIZATION

    EPA Science Inventory

    Three years of PM2.5 speciated data were collected and chemically analyzed using the IMPROVE protocol at the Beacon Hill site in Seattle. The data were analyzed by the Chemical Mass Balance Version 8 (CMB8) and Positive Matrix Factorization (PMF) source apportionment models. T...

  17. SOURCE APPORTIONMENT OF EXPOSURES TO VOLATILE ORGANIC COMPOUNDS: II. APPLICATION OF RECEPTOR MODELS TO TEAM STUDY DATA. (R826788)

    EPA Science Inventory

    Four receptor-oriented source apportionment models were applied to personal exposure measurements for toxic volatile organic compounds (VOCs). The measurements are from the total exposure assessment methodology studies conducted from 1980 to 1984 in New Jersey (NJ) and Califor...

  18. [Source apportionment of soil heavy metals in Jiapigou goldmine based on the UNMIX model].

    PubMed

    Ai, Jian-chao; Wang, Ning; Yang, Jing

    2014-09-01

    The paper determines 16 kinds of metal elements' concentration in soil samples which collected in Jipigou goldmine upper the Songhua River. The UNMIX Model which was recommended by US EPA to get the source apportionment results was applied in this study, Cd, Hg, Pb and Ag concentration contour maps were generated by using Kriging interpolation method to verify the results. The main conclusions of this study are: (1)the concentrations of Cd, Hg, Pb and Ag exceeded Jilin Province soil background values and enriched obviously in soil samples; (2)using the UNMIX Model resolved four pollution sources: source 1 represents human activities of transportation, ore mining and garbage, and the source 1's contribution is 39. 1% ; Source 2 represents the contribution of the weathering of rocks and biological effects, and the source 2's contribution is 13. 87% ; Source 3 is a comprehensive source of soil parent material and chemical fertilizer, and the source 3's contribution is 23. 93% ; Source 4 represents iron ore mining and transportation sources, and the source 4's contribution is 22. 89%. (3)the UNMIX Model results are in accordance with the survey of local land-use types, human activities and Cd, Hg and Pb content distributions.

  19. Space-time quantitative source apportionment of soil heavy metal concentration increments.

    PubMed

    Yang, Yong; Christakos, George; Guo, Mingwu; Xiao, Lu; Huang, Wei

    2017-04-01

    Assessing the space-time trends and detecting the sources of heavy metal accumulation in soils have important consequences in the prevention and treatment of soil heavy metal pollution. In this study, we collected soil samples in the eastern part of the Qingshan district, Wuhan city, Hubei Province, China, during the period 2010-2014. The Cd, Cu, Pb and Zn concentrations in soils exhibited a significant accumulation during 2010-2014. The spatiotemporal Kriging technique, based on a quantitative characterization of soil heavy metal concentration variations in terms of non-separable variogram models, was employed to estimate the spatiotemporal soil heavy metal distribution in the study region. Our findings showed that the Cd, Cu, and Zn concentrations have an obvious incremental tendency from the southwestern to the central part of the study region. However, the Pb concentrations exhibited an obvious tendency from the northern part to the central part of the region. Then, spatial overlay analysis was used to obtain absolute and relative concentration increments of adjacent 1- or 5-year periods during 2010-2014. The spatial distribution of soil heavy metal concentration increments showed that the larger increments occurred in the center of the study region. Lastly, the principal component analysis combined with the multiple linear regression method were employed to quantify the source apportionment of the soil heavy metal concentration increments in the region. Our results led to the conclusion that the sources of soil heavy metal concentration increments should be ascribed to industry, agriculture and traffic. In particular, 82.5% of soil heavy metal concentration increment during 2010-2014 was ascribed to industrial/agricultural activities sources. Using STK and SOA to obtain the spatial distribution of heavy metal concentration increments in soils. Using PCA-MLR to quantify the source apportionment of soil heavy metal concentration increments.

  20. Characterization of Arctic elemental carbon in Barrow, AK using radiocarbon source apportionment

    NASA Astrophysics Data System (ADS)

    Barrett, T. E.; Usenko, S.; Robinson, E. M.; Sheesley, R. J.

    2013-12-01

    Currently, the Arctic is one of the fastest warming regions on earth with surface temperatures increasing at a rate nearly double the global mean over recent decades. Despite the fact that atmospheric concentrations of elemental carbon (EC) are lower in the Arctic than in lower latitudes, deposition of EC on snow and ice may exacerbate regional warming by simultaneously decreasing albedo and increasing melt rates. Due to the intensifying Arctic oil exploration in areas such as the Beaufort and Chukchi seas, the impact of new emission sources such as heavy fuel and heavy diesel combustion on regional carbon needs to be assessed. The first step in developing mitigation strategies for reducing current and future EC emissions in the Arctic is to determine emission source contributions. This study aims to determine the relative contributions of fossil fuel and biomass combustion and to identify major source regions of EC to the Arctic. Radiocarbon analysis of both total organic carbon (TOC) and EC combined with organic tracer and back trajectory analysis has been applied to a set of wintertime coarse particulate matter (PM10) samples from Barrow, AK. Preliminary apportionment for January 2013 indicates roughly half of TOC is from biogenic/biomass burning emissions and one third of EC is due to biomass burning emissions. The radiocarbon results will be combined with organic tracer analysis (polycyclic aromatic hydrocarbons, petroleum biomarkers and normal alkanes), increasing the specificity of the relative contribution of both the fossil and modern (biogenic/biomass burning) carbon emission sources. This research represents the first reported radiocarbon values for Arctic EC, providing highly conclusive source apportionment prior to the influence of increased drilling operations and ship traffic in the Beaufort and Chukchi seas.

  1. Source apportionment of trace metals in river sediments: A comparison of three methods.

    PubMed

    Chen, Haiyang; Teng, Yanguo; Li, Jiao; Wu, Jin; Wang, Jinsheng

    2016-04-01

    Increasing trace metal pollution in river sediment poses a significant threat to watershed ecosystem health. Identifying potential sources of sediment metals and apportioning their contributions are of key importance for proposing prevention and control strategies of river pollution. In this study, three advanced multivariate receptor models, factor analysis with nonnegative constraints (FA-NNC), positive matrix factorization (PMF), and multivariate curve resolution weighted-alternating least-squares (MCR-WALS), were comparatively employed for source apportionment of trace metals in river sediments and applied to the Le'an River, a main tributary of Poyang Lake which is the largest freshwater lake in China. The pollution assessment with contamination factor and geoaccumulation index suggested that the river sediments in Le'an River were contaminated severely by trace metals due to human activities. With the three apportionment tools, similar source profiles of trace metals in sediments were extracted. Especially, the MCR-WALS and PMF models produced essentially the same results. Comparatively speaking, the weighted schemes might give better solutions than the unweighted FA-NNC because the uncertainty information of environmental data was considered by PMF and MCR-WALS. Anthropogenic sources were apportioned as the most important pollution sources influencing the sediment metals in Le'an River with contributions of about 90%. Among them, copper tailings occupied the largest contribution (38.4-42.2%), followed by mining wastewater (29.0-33.5%), and agricultural activities (18.2-18.7%). To protect the ecosystem of Le'an River and Poyang Lake, special attention should be paid to the discharges of mining wastewater and the leachates of copper tailing ponds in that region.

  2. Source apportionment of exposures to volatile organic compounds. I. Evaluation of receptor models using simulated exposure data

    NASA Astrophysics Data System (ADS)

    Miller, Shelly L.; Anderson, Melissa J.; Daly, Eileen P.; Milford, Jana B.

    Four receptor-oriented source apportionment models were evaluated by applying them to simulated personal exposure data for select volatile organic compounds (VOCs) that were generated by Monte Carlo sampling from known source contributions and profiles. The exposure sources modeled are environmental tobacco smoke, paint emissions, cleaning and/or pesticide products, gasoline vapors, automobile exhaust, and wastewater treatment plant emissions. The receptor models analyzed are chemical mass balance, principal component analysis/absolute principal component scores, positive matrix factorization (PMF), and graphical ratio analysis for composition estimates/source apportionment by factors with explicit restriction, incorporated in the UNMIX model. All models identified only the major contributors to total exposure concentrations. PMF extracted factor profiles that most closely represented the major sources used to generate the simulated data. None of the models were able to distinguish between sources with similar chemical profiles. Sources that contributed <5% to the average total VOC exposure were not identified.

  3. [Characteristics and source apportionment of volatile organic compounds (VOCs) in the northern suburb of Nanjing].

    PubMed

    An, Jun-lin; Zhu, Bin; Wang, Hong-lei; Yang, Hui

    2014-12-01

    Based on the data of volatile organic compounds (VOCs) collected continuously from 1st Mar, 2011 to 29th Feb, 2012 in the northern suburb of Nanjing, characteristics of their variability, differences of ratios of tracers and source apportionment by principal component analysis/absolute principal component scores (PCA/APCS) were analyzed. The results showed that the total VOCs mixing ratios were 43.52 x 10(-9), which accounted for 45.1% of alkanes, alkenes for 25.3%, alkyne for 7.3%, and aromatics for 22.3%. There was an obviously seasonal variation of VOCs, with the maximum in summer and the minimum in winter. There was an obvious seasonal variation of VOCs component, with highest alkanes in winter, highest alkenes in summer, highest aromatic in spring, and highest alkyne in winter. By using the specific pollutant ratios ( hydrocarbons/acetylene and toluene/benzene) method, it indicated that the observation site was greatly affected by the surrounding industrial areas. Source analysis of VOCs by PCA/APCS mode showed that the sources consisted of industrial production sources, automobile emission sources, combustion sources, industrial production volatilization sources, solvent use sources and biogenic emission sources. In addition, there were seasonal variations. Overall, the sources related to industrial production activities represented 45% - 63% of VOCs, and they were followed by automobile emission sources, which represented 34% - 50%.

  4. A source apportionment of U.S. fine particulate matter air pollution

    NASA Astrophysics Data System (ADS)

    Thurston, George D.; Ito, Kazuhiko; Lall, Ramona

    2011-08-01

    2.5 components agreed well with the U.S. PM 2.5 observed during the study period (mean = 14.3 μg m -3; R2 = 0.94). Apportionment regression analyses using single-element tracers for each source category gave results consistent with the APCA estimates. Comparisons of nearby sites indicated that the PM 2.5 mass and the secondary aerosols were most homogenous spatially, while traffic PM 2.5 and its tracer, EC, were among the most spatially representative of the source-related components. Comparison of apportionment results to a previous analysis of the 1979-1982 IP Network revealed similar and correlated major U.S. source category factors, albeit at lower levels than in the earlier period, suggesting a consistency in the U.S. spatial patterns of these source-related exposures over time, as well. These results indicate that applying source-apportionment methods to the nationwide CSN can be an informative avenue for identifying and quantifying source components for the subsequent estimation of source-specific health effects, potentially contributing to more efficient regulation of PM 2.5.

  5. Source apportionment of mercury in dust fallout at urban residential area of Central India

    NASA Astrophysics Data System (ADS)

    Pervez, S.; Balakrishna, G.; Tiwari, S.

    2009-10-01

    The components and quantities of atmospheric dust fallout have been reported to be the pollution indicator of large urban areas. The multiplicity and complexity of sources of atmospheric dusts in urban regions (e.g. industrial complexes composed of a variety of industrial processes, automobiles, construction activities etc.) has put forward the need of source apportionment of these sources indicating their contribution to specific environmental receptor. The study presented here is focused on investigation of source contribution estimates of Mercury in urban dust fallout in an urban-industrial area, Raipur, India. Source-receptor based representative sampling plan using longitudinal study design has been adopted. Six sampling sites have been identified on the basis of land use for development plan of anthropogenic activities and factors related to the transportation and dispersion pattern of atmospheric dusts. 24 samples of dust fallout has been collected from each site (one in each month) and subjected to chemical analysis of selected chemical constituents known as markers of selected major dust emitting sources (Steel making average, Road traffic-borne dusts, construction activities, Auto mobile exhaust, and soils). Chemical composition of dust measured at sites marked for identified sources alongwith SPECIATE of USEPA has been used for the preparation of source profiles. Three classified residential receptors (ambient-outdoor, house-indoors and local street-outdoors) have been chosen for development of receptor compositional profiles. Source apportionment has been done using Chemical Mass Balance (CMB 8). Good fit parameters and relative source contribution has been analysed and documented. Dust fallout and respective mercury levels were found tobe higher compared to prescribed standards. Variation in relative contribution of selected sources from site to site within the study area has been occurred. Dominance of local line and area sources (road-traffic and

  6. Characterization and source apportionment of organic aerosol using offline aerosol mass spectrometry

    NASA Astrophysics Data System (ADS)

    Daellenbach, K. R.; Bozzetti, C.; Křepelová, A.; Canonaco, F.; Wolf, R.; Zotter, P.; Fermo, P.; Crippa, M.; Slowik, J. G.; Sosedova, Y.; Zhang, Y.; Huang, R.-J.; Poulain, L.; Szidat, S.; Baltensperger, U.; Prévôt, A. S. H.; El Haddad, I.

    2015-08-01

    Field deployments of the Aerodyne Aerosol Mass Spectrometer (AMS) have significantly advanced real-time measurements and source apportionment of non-refractory particulate matter. However, the cost and complex maintenance requirements of the AMS make impractical its deployment at sufficient sites to determine regional characteristics. Furthermore, the negligible transmission efficiency of the AMS inlet for supermicron particles significantly limits the characterization of their chemical nature and contributing sources. In this study, we utilize the AMS to characterize the water-soluble organic fingerprint of ambient particles collected onto conventional quartz filters, which are routinely sampled at many air quality sites. The method was applied to 256 particulate matter (PM) filter samples (PM1, PM2.5, PM10) collected at 16 urban and rural sites during summer and winter. We show that the results obtained by the present technique compare well with those from co-located online measurements, e.g. AMS or Aerosol Chemical Speciation Monitor (ACSM). The bulk recoveries of organic aerosol (60-91 %) achieved using this technique, together with low detection limits (0.8 μg of organic aerosol on the analyzed filter fraction) allow its application to environmental samples. We will discuss the recovery variability of individual hydrocarbon, oxygen containing and other ions. The performance of such data in source apportionment is assessed in comparison to ACSM data. Recoveries of organic components related to different sources as traffic, wood burning and secondary organic aerosol are presented. This technique, while subjected to the limitations inherent to filter-based measurements (e.g. filter artifacts and limited time resolution) may be used to enhance the AMS capabilities in measuring size-fractionated, spatially-resolved long-term datasets.

  7. Characterization and source apportionment of organic aerosol using offline aerosol mass spectrometry

    NASA Astrophysics Data System (ADS)

    Daellenbach, K. R.; Bozzetti, C.; Křepelová, A.; Canonaco, F.; Wolf, R.; Zotter, P.; Fermo, P.; Crippa, M.; Slowik, J. G.; Sosedova, Y.; Zhang, Y.; Huang, R.-J.; Poulain, L.; Szidat, S.; Baltensperger, U.; El Haddad, I.; Prévôt, A. S. H.

    2016-01-01

    Field deployments of the Aerodyne Aerosol Mass Spectrometer (AMS) have significantly advanced real-time measurements and source apportionment of non-refractory particulate matter. However, the cost and complex maintenance requirements of the AMS make its deployment at sufficient sites to determine regional characteristics impractical. Furthermore, the negligible transmission efficiency of the AMS inlet for supermicron particles significantly limits the characterization of their chemical nature and contributing sources. In this study, we utilize the AMS to characterize the water-soluble organic fingerprint of ambient particles collected onto conventional quartz filters, which are routinely sampled at many air quality sites. The method was applied to 256 particulate matter (PM) filter samples (PM1, PM2.5, and PM10, i.e., PM with aerodynamic diameters smaller than 1, 2.5, and 10 µm, respectively), collected at 16 urban and rural sites during summer and winter. We show that the results obtained by the present technique compare well with those from co-located online measurements, e.g., AMS or Aerosol Chemical Speciation Monitor (ACSM). The bulk recoveries of organic aerosol (60-91 %) achieved using this technique, together with low detection limits (0.8 µg of organic aerosol on the analyzed filter fraction) allow its application to environmental samples. We will discuss the recovery variability of individual hydrocarbon ions, ions containing oxygen, and other ions. The performance of such data in source apportionment is assessed in comparison to ACSM data. Recoveries of organic components related to different sources as traffic, wood burning, and secondary organic aerosol are presented. This technique, while subjected to the limitations inherent to filter-based measurements (e.g., filter artifacts and limited time resolution) may be used to enhance the AMS capabilities in measuring size-fractionated, spatially resolved long-term data sets.

  8. Comparison of the MURA and an improved single-receptor (SIRA) trajectory source apportionment (TSA) method using artificial sources

    NASA Astrophysics Data System (ADS)

    Lee, Stephanie; Ashbaugh, Lowell

    Two trajectory source apportionment methods were tested using an artificially generated data set to determine their ability to detect the known sources. The forward-looking step from the multi-receptor trajectory analysis (MURA) method was added to the conditional probability (CP)method of Ashbaugh et al. [1985. A residence time probability analysis of sulfur concentrations at Grand Canyon National Park. Atmospheric Environment 19(8), 1263-1270] to develop the single-receptor forward CP (SIRA) method. The multi-receptor (MURA) and the SIRA methods were tested with three simulations using artificially generated sources. The ability of the methods to detect the sources was quantified for each simulation. The first simulation showed that the SIRA method is an improvement over the original CP method. The MURA trajectory method proved to be superior at identifying sources for the simulation located in the west and comparable to the SIRA method for the two simulations located in the east.

  9. Source-apportionment and model evaluation: experiences with the EMEP SOA model

    NASA Astrophysics Data System (ADS)

    Simpson, D.; Yttri, K. E.

    2009-04-01

    The EMEP MSC-W chemical transport model (Simpson et al., 2003) has been successfully used for the prediction of photochemical oxidants and various inorganic aerosol components (sulphate, nitrate, ammonium) for many years. The model generally performs well for such species, as should be expected for compounds whose emission sources and chemistry are fairly well know. For carbonaceous particulate matter (PCM) however the model has been found to give very different results in different parts of Europe, with typically poor performance in southern Europe, but rather good results in Northern Europe (Simpson et al., 2007). Earlier comparison with the results of source-apportionment studies from the CARBOSOL project (Gelencser et al., 2007, Simpson et al., 2007) has shown that the poor performance in southern Europe can partly be ascribed to difficulties with emissions from residential wood-burning, and partly due to an underestimate of the secondary organic aerosol (SOA) component. Such difficulties are expected for organic aerosols, a subject where the basic science is only partially understood, and where new experimental results continually lead to revisions in existing ideas concerning sources and formation mechanisms (e.g. Hallquist et al., 2009). In such a situation, it is essential that model results are evaluated as thoroughly as possible, and that where possible the various components of organic aerosol can be evaluated separately. A number of source-apportionment (SA) studies have recently become available in Europe, in which data on elemental carbon (EC), organic carbon (OC), 14C, levoglucosan, and various markers of primary organic carbon (cellulose, sugars/sugar-alcohols) have allowed estimates of various sources of carbonaceous particulate matter (PCM). As well as CARBOSOL, these studies include various sites in Switzerland (e.g. Lanz et al., 2008, Szidat et al., 2006), data are available from Gothenburg in Sweden (Szidat et al., 2008) and from southern

  10. Source apportionment of PAH in Hamilton Harbour suspended sediments: comparison of two factor analysis methods

    SciTech Connect

    Uwayemi M. Sofowote; Brian E. McCarry; Christopher H. Marvin

    2008-08-15

    A total of 26 suspended sediment samples collected over a 5-year period in Hamilton Harbour, Ontario, Canada and surrounding creeks were analyzed for a suite of polycyclic aromatic hydrocarbons and sulfur heterocycles. Hamilton Harbour sediments contain relatively high levels of polycyclic aromatic compounds and heavy metals due to emissions from industrial and mobile sources. Two receptor modeling methods using factor analyses were compared to determine the profiles and relative contributions of pollution sources to the harbor; these methods are principal component analyses (PCA) with multiple linear regression analysis (MLR) and positive matrix factorization (PMF). Both methods identified four factors and gave excellent correlation coefficients between predicted and measured levels of 25 aromatic compounds; both methods predicted similar contributions from coal tar/coal combustion sources to the harbor (19 and 26%, respectively). One PCA factor was identified as contributions from vehicular emissions (61%); PMF was able to differentiate vehicular emissions into two factors, one attributed to gasoline emissions sources (28%) and the other to diesel emissions sources (24%). Overall, PMF afforded better source identification than PCA with MLR. This work constitutes one of the few examples of the application of PMF to the source apportionment of sediments; the addition of sulfur heterocycles to the analyte list greatly aided in the source identification process. 41 refs., 3 figs., 2 tabs.

  11. Isotope source apportionment of carbonaceous aerosol as a function of particle size and thermal refractiveness

    NASA Astrophysics Data System (ADS)

    Masalaite, Agne; Holzinger, Rupert; Remeikis, Vidmantas; Röckmann, Thomas; Dusek, Ulrike

    2016-04-01

    The stable carbon isotopes can be used to get information about sources and processing of carbonaceous aerosol. We will present results from source apportionment of carbonaceous aerosol as a function of particle size thermal refractiveness. Separate source apportionment for particles smaller than 200 nm and for different carbon volatility classes are rarely reported and give new insights into aerosol sources in the urban environment. Stable carbon isotope ratios were measured for the organic carbon (OC) fraction and total carbon (TC) of MOUDI impactor samples that were collected on a coastal site (Lithuania) during the winter 2012 and in the city of Vilnius (Lithuania) during the winter of 2009. The 11 impactor stages spanned a size range from 0.056 to 18 μm, but only the 6 stages in the submicron range were analysed. The δ13C values of bulk total carbon (δ13CTC) were determined with an elemental analyser (Flash EA 1112) coupled with an isotope ratio mass spectrometer (Thermo Finnigan Delta Plus Advantage) (EA - IRMS). Meanwhile δ13COC was measured using thermal-desorption isotope ratio mass spectrometry (IRMS) system. This allows a rough separation of the more volatile OC fraction (desorbed in the oven of IRMS up to 250 0C) from the more refractory fraction (desorbed up to 400 0C). In this study we investigated the composition of organic aerosol desorbed from filter samples at different temperatures using the thermal-desorption proton-transfer-reaction mass spectrometry (TD-PTR-MS) technique. During winter-time in Lithuania we expect photochemistry and biogenic emissions to be of minor importance. The main sources of aerosol carbon should be fossil fuel and biomass combustion. In both sites, the coastal and the urban site, δ13C measurements give a clear indication that the source contributions differ for small and large particles. Small particles < 200 nm are depleted in 13C with respect to larger particles by 1 - 2 ‰Ṫhis shows that OC in small particle

  12. Quantitative identification and source apportionment of anthropogenic heavy metals in marine sediment of Hong Kong

    NASA Astrophysics Data System (ADS)

    Zhou, Feng; Guo, Huaicheng; Liu, Lei

    2007-10-01

    Based on ten heavy metals collected twice annually at 59 sites from 1998 to 2004, enrichment factors (EFs), principal component analysis (PCA) and multivariate linear regression of absolute principal component scores (MLR-APCS) were used in identification and source apportionment of the anthropogenic heavy metals in marine sediment. EFs with Fe as a normalizer and local background as reference values was properly tested and suitable in Hong Kong, and Zn, Ni, Pb, Cu, Cd, Hg and Cr mainly originated from anthropogenic sources, while Al, Mn and Fe were derived from rocks weathering. Rotated PCA and GIS mapping further identified two types of anthropogenic sources and their impacted regions: (1) electronic industrial pollution, riparian runoff and vehicle exhaust impacted the entire Victoria Harbour, inner Tolo Harbour, Eastern Buffer, inner Deep Bay and Cheung Chau; and (2) discharges from textile factories and paint, influenced Tsuen Wan Bay and Kwun Tong typhoon shelter and Rambler Channel. In addition, MLR-APCS was successfully introduced to quantitatively determine the source contributions with uncertainties almost less than 8%: the first anthropogenic sources were responsible for 50.0, 45.1, 86.6, 78.9 and 87.5% of the Zn, Pb, Cu, Cd and Hg, respectively, whereas 49.9% of the Ni and 58.4% of the Cr came from the second anthropogenic sources.

  13. Characterization and source apportionment of water pollution in Jinjiang River, China.

    PubMed

    Chen, Haiyang; Teng, Yanguo; Yue, Weifeng; Song, Liuting

    2013-11-01

    Characterizing water quality and identifying potential pollution sources could greatly improve our knowledge about human impacts on the river ecosystem. In this study, fuzzy comprehensive assessment (FCA), pollution index (PI), principal component analysis (PCA), and absolute principal component score-multiple linear regression (APCS-MLR) were combined to obtain a deeper understanding of temporal-spatial characterization and sources of water pollution with a case study of the Jinjiang River, China. Measurement data were obtained with 17 water quality variables from 20 sampling sites in the December 2010 (withered water period) and June 2011 (high flow period). FCA and PI were used to comprehensively estimate the water quality variables and compare temporal-spatial variations, respectively. Rotated PCA and receptor model (APCS-MLR) revealed potential pollution sources and their corresponding contributions. Application results showed that comprehensive application of various multivariate methods were effective for water quality assessment and management. In the withered water period, most sampling sites were assessed as low or moderate pollution with characteristics pollutants of permanganate index and total nitrogen (TN), whereas 90% sites were classified as high pollution in the high flow period with higher TN and total phosphorus. Agricultural non-point sources, industrial wastewater discharge, and domestic sewage were identified as major pollution sources. Apportionment results revealed that most variables were complicatedly influenced by industrial wastewater discharge and agricultural activities in withered water period and primarily dominated by agricultural runoff in high flow period.

  14. Development of a chemical source apportionment decision support framework for catchment management.

    PubMed

    Comber, Sean D W; Smith, Russell; Daldorph, Peter; Gardner, Michael J; Constantino, Carlos; Ellor, Brian

    2013-09-03

    EU legislation, including the Water Framework Directive, has led to the application of increasingly stringent quality standards for a wide range of chemical contaminants in surface waters. This has raised the question of how to determine and to quantify the sources of such substances so that measures can be taken to address breaches of these quality standards using the polluter pays principle. Contaminants enter surface waters via a number of diffuse and point sources. Decision support tools are required to assess the relative magnitudes of these sources and to estimate the impacts of any programmes of measures. This work describes the development and testing of a modeling framework, the Source Apportionment Geographical Information System (SAGIS). The model uses readily available national data sets to estimate contributions of a number of nutrients (nitrogen and phosphorus), metals (copper, zinc, cadmium, lead, mercury, and nickel) and organic chemicals (a phthalate and a number of polynuclear aromatic hydrocarbons) from multiple sector sources. Such a tool has not previously been available on a national scale for such a wide range of chemicals. It is intended to provide a common platform to assist stakeholders in future catchment management.

  15. Chemical mass balance source apportionment of PM 10 in an industrialized urban area of Northern Greece

    NASA Astrophysics Data System (ADS)

    Samara, C.; Kouimtzis, Th; Tsitouridou, R.; Kanias, G.; Simeonov, V.

    Ambient PM 10 were sampled at three sites in an industrialized urban area of Northern Greece during June 1997-June 1998 and analyzed for 17 chemical elements, 5 water-soluble ions and 13 polycyclic aromatic hydrocarbons. In addition, chemical source profiles consisting of the same particulate components were obtained for a number of industrial activities (cement, fertilizer and asphalt production, quarry operations, metal electroplating, metal welding and tempering, steel manufacture, lead and bronze smelters, metal scrap incineration), residential oil burning, non-catalyst and catalyst-equipped passenger cars, diesel fuelled taxis and buses, as well as for geological fugitive sources (paved road dust and soil from open lands). Ambient and source data were used in a chemical mass balance (CMB) receptor model for source identification and apportionment. Results of CMB modeling showed that major source of ambient PM 10 at all three sites was diesel vehicle exhaust. Significant contribution from industrial oil burning was also evidenced at the site located closest to the industrial area.

  16. Source apportionment of airborne particulate matter for the speciation trends network site in Cleveland, OH

    SciTech Connect

    Liming Zhou; Philip K. Hopke; Weixiang Zhao

    2009-03-15

    Aerosol composition data from the Speciation Trends Network (STN) site (East 14th Street) in Cleveland, OH, were analyzed by advanced receptor model methods for source apportionment as well as by the standard positive matrix factorization (PMF) using PMF2. These different models are used in combination to test model limitations. These data were 24-hr average mass concentrations and compositions obtained for samples taken every third day from 2001 to 2003. The Multilinear Engine (ME) was used to solve an expanded model to estimate the source profiles and source contributions and also to investigate the wind speed, wind direction, time-of-day, weekend/weekday, and seasonal effects. PMF2 was applied to the same dataset. Potential source contribution function (PSCF) and conditional probability function (CPF) analyses were used to locate the regional and local sources using the resolved source contributions and appropriate meteorological data. Very little difference was observed between the results of the expanded model and the PMF2 values for the profiles and source contribution time series. The identified sources were as ferrous smelter, secondary sulfate, secondary nitrate, soil/combustion mixture, steel mill, traffic, wood smoke, and coal burning. The CPF analysis was useful in helping to identify local sources, whereas the PSCF results were only useful for regional source areas. Both of these analyses were more useful than the wind directional factor derived from the expanded factor analysis. However, the expanded analysis provided direct information on seasonality and day-of-week behavior of the sources. 28 refs., 8 figs., 4 tabs.

  17. Thia-arenes as source apportionment tracers for urban air particulate

    SciTech Connect

    McCarry, B.E.; Allan, L.M.; Mehta, S.; Marvin, C.H.

    1995-12-31

    Over sixty respirable air particulate samples were selected from a large number of filters collected in Hamilton, Ontario, Canada. Depending on the wind direction these sites were either predominantly upwind or predominantly downwind of the industrial sources. The sixty filters were extracted and analyzed using GC-MS for a range of PAH and sulfur-containing PAH (thia-arenes). Various reference standards (coal tar, diesel exhaust, urban air particulate) and source samples (coke oven condensate) were analyzed as well. A set of air particulate samples collected in another city alongside a highway provided an urban vehicular air sample. Unique thia-arene profiles were noted in the reference and source samples which provided the basis for this source apportionment work; two main approaches were used: (1) analysis of alkylated derivatives of thia-arenes with a molecular mass of 184 amu and (2) analysis of 234 amu isomers. The diesel exhaust and urban vehicular samples gave identical profiles while the coal tar and coke oven samples also had identical profiles but in different respects. The air samples collected at samplers located upwind of the coke ovens showed thia-arene profiles which were similar to the profile observed with a diesel exhaust reference material. However, air samples collected downwind of the coke ovens were heavily loaded samples and resembled the coal tar coke and oven condensate samples.

  18. Source apportionment of traffic emissions of particulate matter using tunnel measurements

    NASA Astrophysics Data System (ADS)

    Lawrence, Samantha; Sokhi, Ranjeet; Ravindra, Khaiwal; Mao, Hongjun; Prain, Hunter Douglas; Bull, Ian D.

    2013-10-01

    This study aims to quantify exhaust/non-exhaust emissions and the uncertainties associated with them by combining innovative motorway tunnel sampling and source apportionment modelling. Analytical techniques ICP-AES and GC-MS were used to identify the metallic and organic composition of PM10, respectively. Good correlation was observed between Fe, Cu, Mn, Ni, Pb and Sb and change in traffic volume. The concentration of polycyclic aromatic hydrocarbons and other organics varies significantly at the entrance and exit site of the tunnel, with fluoranthene, pyrene, benzo[a]pyrene, chrysene and benzothiazole having the highest incremented concentrations. The application of Principal Component Analysis and Multiple Linear Regression Analysis helped to identify the emission sources for 82% of the total PM10 mass inside the tunnel. Identified sources include resuspension (27%), diesel exhaust emissions (21%), petrol exhaust emissions (12%), brake wear emissions (11%) and road surface wear (11%). This study shows that major health related chemical species of PM10 originate from non-exhaust sources, further signifying the need for legislation to reduce these emissions.

  19. Source apportionment for African dust outbreaks over the Western Mediterranean using the HYSPLIT model

    NASA Astrophysics Data System (ADS)

    Escudero, M.; Stein, A. F.; Draxler, R. R.; Querol, X.; Alastuey, A.; Castillo, S.; Avila, A.

    2011-03-01

    A source apportionment technique has been applied to determine the geographical distribution of emissions in Northern Africa contributing to dust outbreaks that yield high PM10 levels at Spanish regional background stations. Seven dust episodes have been analyzed in this study. Total suspended particles have been sampled and chemically analyzed for these events at La Castanya background station (Montseny, NE Spain) and differences in the composition of airborne dust have been studied. The dominant role of northern and western source areas (Tunisia, Algeria, Mauritania and the Western Sahara) contrasted with the negligible contribution of major emission source areas such as the Bodelé depression, Libya, Niger, and Sudan. During the simulated events using the dust module of the HYSPLIT model, material from the latter regions is persistently transported across the Atlantic but not towards Western Europe. As a consequence, the composition of the dust turned out to be quite homogeneous since the mixing of dust occurs from various source areas with similar chemical composition. However, differences in Ca/Al ratios have been found in a number of samples that are mainly explained by vertical transport segregation of clay minerals (relatively richer in Al) from coarser dust particles (Ca-carbonate).

  20. Source apportionment of atmospheric PAHs and their toxicity using PMF: Impact of gas/particle partitioning

    NASA Astrophysics Data System (ADS)

    Gao, Bo; Wang, Xin-Ming; Zhao, Xiu-Ying; Ding, Xiang; Fu, Xiao-Xin; Zhang, Yan-Li; He, Quan-Fu; Zhang, Zhou; Liu, Teng-Yu; Huang, Zou-Zhao; Chen, Lai-Guo; Peng, Yan; Guo, Hai

    2015-02-01

    24-h PM2.5 samples were simultaneously collected at six sites in a subtropical city of South China during November-December, 2009. Particle-phase concentrations of polycyclic aromatic hydrocarbons (PAHs) and organic tracers such as hopanes for vehicular emissions (VE), levoglucosan for biomass burning (BB) and picene for coal combustion (CC) were determined. Meanwhile, their gas-phase concentrations were calculated from gas/particle (G/P) partitioning theory using the particle-phase concentrations. The 4 ring PAHs (fluoranthene to chrysene) had lower particle-phase fractions (10%-79%) than other species. Estimated BaPeq and lifetime cancer risk for particle-only (P-only) vs gas + particle (G + P) data sets showed similar values, indicating PAHs with 5-7 rings dominated the carcinogenicity of PAHs. Positive Matrix Factorization (PMF) was applied on both P-only and G + P data sets to estimate the source contributions to PAHs and their toxicity. Three common sources were identified: VE, BB and CC, with CC as the most significant source for both particulate (58%) and total (G + P, 40%) PAHs. While CC exhibited consistent contributions to BaPeq for P-only (66%) vs G + P (62%) solutions, VE and BB contributions were under- and overestimated by 68% and 47%, respectively by the P-only solution, as compared to the G + P solution. The results provide an insight on the impact of G/P partitioning on the source apportionment of PAHs and their toxicity.

  1. Source apportionment of aerosol particles near a steel plant by electron microscopy.

    PubMed

    Ebert, Martin; Müller-Ebert, Dörthe; Benker, Nathalie; Weinbruch, Stephan

    2012-12-01

    The size, morphology and chemical composition of 37,715 individual particles collected over 22 sampling days in the vicinity of a large integrated steel production were studied by scanning and transmission electron microscopy. Based on the morphology, chemistry and beam stability the particles were classified into the following fourteen groups: silicates, sea salt, calcium sulfates, calcium carbonates, carbonate-silicate mixtures, sulfate-silicate mixtures, iron oxides, iron mixtures, metal oxide-metals, complex secondary particles, soot, Cl-rich particles, P-rich particles, and other particles. The majority of iron oxide (≈85%) and metal oxide-metal (≈70%) particles as well as ≈20% of the silicate particles are fly ashes from high temperature processes. The emissions from the steel work are dominated by iron oxide particles. For source apportionment, seven source categories and two sectors of local wind direction (industrial and urban background) were distinguished. In both sectors PM₁₀ consists of four major source categories: 35% secondary, 20% industrial, 17% soil and 16% soot in the urban background sector compared to 45% industrial, 20% secondary, 13% soil, and 9% soot in the industrial sector. As the secondary and the soot components are higher in the urban background sector than in the industrial sector, it is concluded that both components predominantly originate from urban background sources (traffic, coal burning, and domestic heating). Abatement measures should not only focus on the steel work but should also include the urban background aerosol.

  2. Source apportionment of PM10 in the Western Mediterranean based on observations from a cruise ship

    NASA Astrophysics Data System (ADS)

    Schembari, C.; Bove, M. C.; Cuccia, E.; Cavalli, F.; Hjorth, J.; Massabò, D.; Nava, S.; Udisti, R.; Prati, P.

    2014-12-01

    Two intensive PM10 sampling campaigns were performed in the summers of 2009 and 2010 on the ship Costa Pacifica during cruises in the Western Mediterranean. Samples, mainly collected on an hourly basis, were analysed with different techniques (Particle Induced X-Ray Emission, PIXE; Energy Dispersive - X Ray Fluorescence, ED-XRF; Ion Chromatography, IC; Thermo-optical analysis) to retrieve the PM10 composition and its time pattern. The data were used for obtaining information about the sources of aerosol, with a focus on ship emissions, through apportionment using chemical marker compounds, correlation analysis and Positive Matrix Factorization (PMF) receptor modelling. For the campaign in 2010, 66% of the aerosol sulphate was found to be anthropogenic, only minor contributions of dust and sea salt sulphate were observed while the biogenic contribution, estimated based on the measurements of MSA, was found to be more important (26%), but influenced by large uncertainties. V and Ni were found to be suitable tracers of ship emissions during the campaigns. Four sources of aerosol were resolved by the PMF analysis; the source having the largest impact on PM10, BC and sulphate was identified as a mixed source, comprising emissions from ships. The correlations between sulphate and V and Ni showed the influence of ship emissions on sulphate in marine air masses. For the leg Palma-Tunis crossing a main ship route, the correlations between aerosol sulphate and V and Ni were particularly strong (r2 = 0.9 for both elements).

  3. Source apportionment of PM2.5 carbonaceous aerosol in Baghdad, Iraq

    NASA Astrophysics Data System (ADS)

    Hamad, Samera Hussein; Schauer, James Jay; Heo, Jongbae; Kadhim, Ahmed K. H.

    2015-04-01

    Baghdad is the second largest city in the Middle East and suffers from severe air quality degradation due to the high levels of the atmospheric particulate matter (PM). Limited information exists regarding the sources of PM in Baghdad, and the lack of information on sources inhibits the development of control strategies to reduce air pollution. To better understand the nature of fine particulate matter (PM2.5) in Baghdad and the Middle East, a one year sampling campaign to collect PM2.5 was conducted from September 2012 through September 2013, missing August 2013 samples due to the security situation. 24-hour integrated samples collected on a 1-in-6 day schedule were analyzed for the major components, and monthly average samples were analyzed by gas chromatography mass spectrometry (GCMS) methods to measure particle-phase organic molecular markers. The results of organic molecular markers were used in a chemical mass balance (CMB) model to quantify the sources of PM2.5 organic carbon (OC) and PM2.5 mass. Primary sources accounted for 44% of the measured PM2.5, and secondary sources were estimated to make up 28% of the measured PM2.5. Picene, a tracer of coal combustion detected in Baghdad where there is no evidence for coal combustion, can be attributed to burning crude oil and other low quality fuels in Baghdad. Source apportionment results showed that the dominant sources of the carbonaceous aerosols in Baghdad are gasoline (37 ± 6%) and diesel engines (17 ± 3%) which can be attributed to the extensive use of gasoline and diesel powered generators in Baghdad. Wood burning and residual oil combustion contributed to 5 ± 0.4 and 1 ± 0.2% respectively of OC. The unresolved sources contributed to 42 ± 19% of the OC which represented the secondary organic aerosol (SOA) and the unidentified sources.

  4. Source apportionment of VOCs in the Los Angeles area using positive matrix factorization

    NASA Astrophysics Data System (ADS)

    Brown, Steven G.; Frankel, Anna; Hafner, Hilary R.

    Eight 3-h speciated hydrocarbon measurements were collected daily by the South Coast Air Quality Management District (SCAQMD) as part of the Photochemical Assessment Monitoring Stations (PAMS) program during the summers of 2001-03 at two sites in the Los Angeles air basin, Azusa and Hawthorne. Over 30 hydrocarbons from over 500 samples at Azusa and 600 samples at Hawthorne were subsequently analyzed using the multivariate receptor model positive matrix factorization (PMF). At Azusa and Hawthorne, five and six factors were identified, respectively, with a good comparison between predicted and measured mass. At Azusa, evaporative emissions (a median of 31% of the total mass), motor vehicle exhaust (22%), liquid/unburned gasoline (27%), coatings (17%), and biogenic emissions (3%) factors were identified. Factors identified at Hawthorne were evaporative emissions (a median of 34% of the total mass), motor vehicle exhaust (24%), industrial process losses (15%), natural gas (13%), liquid/unburned gasoline (13%), and biogenic emissions (1%). Together, the median contribution from mobile source-related factors (exhaust, evaporative emissions, and liquid/unburned gasoline) was 80% and 71% at Azusa and Hawthorne, respectively, similar to previous source apportionment results using the chemical mass balance (CMB) model. There is a difference in the distribution among mobile source factors compared to the CMB work, with an increase in the contribution from evaporative emissions, though the cause (changes in emissions or differences between models) is unknown.

  5. Measurement of greenhouse gases (GHGs) and source apportionment in Bakersfield, CA during CALNEX 2010

    NASA Astrophysics Data System (ADS)

    Guha, A.; Gentner, D. R.; Goldstein, A.; Provencal, R. A.; Gardner, A.; Calnex Bakersfield Science Team

    2010-12-01

    The California Global Warming Solutions Act 2006 creates a need to validate and improve the GHG inventory of the State, which has been largely based on activity and emission factor based estimates. As part of CALNEX 2010, we conducted measurements at the Bakersfield supersite of CO2, CH4, and N2O using fast response laser analyzers (LGR Inc.) to document the ambient mixing ratios of GHGs and analyze their major sources in the region, with an emphasis on understanding emissions of methane (CH4) and nitrous oxide (N2O). The site was located downwind of the urban center during the day and usually experienced a reversal of wind direction at night. Bakersfield is an urban area with heavy industrialization including petroleum refineries, oilfields, manufacturing, and cogeneration plants, all of which can be sources of the abovementioned GHGs. The site was close to a highway and potentially subject to vehicular CH4 and N2O emissions. Hence, CO and a broad variety of VOCs, which can serve as tracers (particularly for vehicle emissions), were included in the measurements to help with source apportionment. In addition to typical urban and industrial sources, Kern County is a rich agricultural region and includes a large number of cattle feedlots, dairies, settling ponds and landfills which are assumed to be some of the largest anthropogenic sources of methane in the State. Additionally, the agricultural industry uses significant amounts of fertilizers, which can lead to production of N2O from the soils along with emissions from controlled biomass burning of agricultural waste. The three GHGs studied show a strong diurnal pattern with concentrations building up in the night-time as the planetary boundary layer (PBL) becomes smaller and reversal in wind direction causes the site to become downwind of some GHG sources like landfills and feedlots. The mean background concentrations at the site (CNO2= 323 ppb; CCO2 = 390 ppm) during the day were consistent with those from the

  6. Determination of buffering capacity of total suspended particle and its source apportionment using the chemical mass balance approach.

    PubMed

    Bi, Xiao-Hui; Feng, Yin-Chang; Zhu, Tan; Zhang, Yu-Fen; Wu, Jian-Hui; Li, Xiang

    2011-01-01

    The samples of total suspended particle (TSP) from sources and TSP in the ambient atmosphere were collected in 2006 at Tianjin, People's Republic of China and analyzed for 16 chemical elements, two water-soluble ions, total carbon, and organic carbon. On the basis of the chemical mass balance (CMB) model, the contributions of different TSP sources to the ambient TSP were identified. The results showed that resuspended dust has the biggest contributions to the concentration of ambient TSP. The buffering capacity of each TSP source was also determined by an analytical chemistry method, and the result showed that the constructive dust (the dust emitted from construction work) had the strongest buffering capacity among the measured sources, whereas the coal combustion dust had the weakest buffering capacity. A calculation formula of the source of buffering capacity of ambient TSP was developed based on the result of TSP source apportionment and the identification of the buffering capacity of each TSP source in this study. The results of the source apportionment of the buffering capacity of ambient TSP indicated that open sources (including soil dust, resuspended dust, and constructive dust) were the dominant sources of the buffering capacity of the ambient TSP. Acid rain pollution in cities in Northern China might become serious with a decrease of open source pollution without reducing acidic sources. More efforts must be made to evaluate this potential risk, and countermeasures should be proposed as early as possible.

  7. Application of hierarchical Bayesian unmixing models in river sediment source apportionment

    NASA Astrophysics Data System (ADS)

    Blake, Will; Smith, Hugh; Navas, Ana; Bodé, Samuel; Goddard, Rupert; Zou Kuzyk, Zou; Lennard, Amy; Lobb, David; Owens, Phil; Palazon, Leticia; Petticrew, Ellen; Gaspar, Leticia; Stock, Brian; Boeckx, Pacsal; Semmens, Brice

    2016-04-01

    Fingerprinting and unmixing concepts are used widely across environmental disciplines for forensic evaluation of pollutant sources. In aquatic and marine systems, this includes tracking the source of organic and inorganic pollutants in water and linking problem sediment to soil erosion and land use sources. It is, however, the particular complexity of ecological systems that has driven creation of the most sophisticated mixing models, primarily to (i) evaluate diet composition in complex ecological food webs, (ii) inform population structure and (iii) explore animal movement. In the context of the new hierarchical Bayesian unmixing model, MIXSIAR, developed to characterise intra-population niche variation in ecological systems, we evaluate the linkage between ecological 'prey' and 'consumer' concepts and river basin sediment 'source' and sediment 'mixtures' to exemplify the value of ecological modelling tools to river basin science. Recent studies have outlined advantages presented by Bayesian unmixing approaches in handling complex source and mixture datasets while dealing appropriately with uncertainty in parameter probability distributions. MixSIAR is unique in that it allows individual fixed and random effects associated with mixture hierarchy, i.e. factors that might exert an influence on model outcome for mixture groups, to be explored within the source-receptor framework. This offers new and powerful ways of interpreting river basin apportionment data. In this contribution, key components of the model are evaluated in the context of common experimental designs for sediment fingerprinting studies namely simple, nested and distributed catchment sampling programmes. Illustrative examples using geochemical and compound specific stable isotope datasets are presented and used to discuss best practice with specific attention to (1) the tracer selection process, (2) incorporation of fixed effects relating to sample timeframe and sediment type in the modelling

  8. Source apportionment of surface ozone in the Yangtze River Delta, China in the summer of 2013

    NASA Astrophysics Data System (ADS)

    Li, L.; An, J. Y.; Shi, Y. Y.; Zhou, M.; Yan, R. S.; Huang, C.; Wang, H. L.; Lou, S. R.; Wang, Q.; Lu, Q.; Wu, J.

    2016-11-01

    We applied ozone source apportionment technology (OSAT) with tagged tracers coupled within the Comprehensive Air Quality Model with Extensions (CAMx) to study the region and source category contribution to surface ozone in the Yangtze River Delta area in summer of 2013. Results indicate that the daytime ozone concentrations in the YRD region are influenced by emissions both locally, regionally and super-regionally. At urban Shanghai, Hangzhou and Suzhou receptors, the ozone formation is mainly VOC-limited, precursor emissions form Zhejiang province dominate their O3 concentrations. At the junction area among two provinces and Shanghai city, the ozone is usually influenced by all the three areas. The daily max O3 at the Dianshan Lake in July are contributed by Zhejiang (48.5%), Jiangsu (11.7%), Anhui (11.6%) and Shanghai (7.4%), long-range transport constitutes around 20.9%. At Chongming site, the BVOC emissions rate is higher than urban region. Regional contribution results show that Shanghai constitutes 15.6%, Jiangsu contributes 16.2% and Zhejiang accounts for 25.5% of the daily max O3. The analysis of the source category contribution to high ozone in the Yangtze River Delta region indicates that the most significant anthropogenic emission source sectors contributing to O3 pollution include industry, vehicle exhaust, although the effects vary with source sector and selected pollution episodes. Emissions of NOx and VOCs emitted from the fuel combustion of industrial boilers and kilns, together with VOCs emissions from industrial process contribute a lot to the high concentrations in urban Hangzhou, Suzhou and Shanghai. The contribution from regional elevated power plants cannot be neglected, especially to Dianshan Lake. Fugitive emissions of volatile pollution sources also have certain contribution to regional O3. These results indicate that the regional collaboration is of most importance to reduce ambient ozone pollution, particularly during high ozone episodes.

  9. Source Apportionment Using Positive Matrix Factorization on Daily Measurements of Inorganic and Organic Speciated PM(2.5).

    PubMed

    Dutton, Steven J; Vedal, Sverre; Piedrahita, Ricardo; Milford, Jana B; Miller, Shelly L; Hannigan, Michael P

    2010-07-01

    Particulate matter less than 2.5 microns in diameter (PM(2.5)) has been linked with a wide range of adverse health effects. Determination of the sources of PM(2.5) most responsible for these health effects could lead to improved understanding of the mechanisms of such effects and more targeted regulation. This has provided the impetus for the Denver Aerosol Sources and Health (DASH) study, a multi-year source apportionment and health effects study relying on detailed inorganic and organic PM(2.5) speciation measurements.In this study, PM(2.5) source apportionment is performed by coupling positive matrix factorization (PMF) with daily speciated PM(2.5) measurements including inorganic ions, elemental carbon (EC) and organic carbon (OC), and organic molecular markers. A qualitative comparison is made between two models, PMF2 and ME2, commonly used for solving the PMF problem. Many previous studies have incorporated chemical mass balance (CMB) for organic molecular marker source apportionment on limited data sets, but the DASH data set is large enough to use multivariate factor analysis techniques such as PMF.Sensitivity of the PMF2 and ME2 models to the selection of speciated PM(2.5) components and model input parameters was investigated in depth. A combination of diagnostics was used to select an optimum, 7-factor model using one complete year of daily data with pointwise measurement uncertainties. The factors included 1) a wintertime/methoxyphenol factor, 2) an EC/sterane factor, 3) a nitrate/polycyclic aromatic hydrocarbon (PAH) factor, 4) a summertime/selective aliphatic factor, 5) an n-alkane factor, 6) a middle oxygenated PAH/alkanoic acid factor and 7) an inorganic ion factor. These seven factors were qualitatively linked with known PM(2.5) emission sources with varying degrees of confidence. Mass apportionment using the 7-factor model revealed the contribution of each factor to the mass of OC, EC, nitrate and sulfate. On an annual basis, the majority of OC

  10. Source apportionment using positive matrix factorization on daily measurements of inorganic and organic speciated PM 2.5

    NASA Astrophysics Data System (ADS)

    Dutton, Steven J.; Vedal, Sverre; Piedrahita, Ricardo; Milford, Jana B.; Miller, Shelly L.; Hannigan, Michael P.

    2010-07-01

    Particulate matter less than 2.5 microns in diameter (PM 2.5) has been linked with a wide range of adverse health effects. Determination of the sources of PM 2.5 most responsible for these health effects could lead to improved understanding of the mechanisms of such effects and more targeted regulation. This has provided the impetus for the Denver Aerosol Sources and Health (DASH) study, a multi-year source apportionment and health effects study relying on detailed inorganic and organic PM 2.5 speciation measurements. In this study, PM 2.5 source apportionment is performed by coupling positive matrix factorization (PMF) with daily speciated PM 2.5 measurements including inorganic ions, elemental carbon (EC) and organic carbon (OC), and organic molecular markers. A qualitative comparison is made between two models, PMF2 and ME2, commonly used for solving the PMF problem. Many previous studies have incorporated chemical mass balance (CMB) for organic molecular marker source apportionment on limited data sets, but the DASH data set is large enough to use multivariate factor analysis techniques such as PMF. Sensitivity of the PMF2 and ME2 models to the selection of speciated PM 2.5 components and model input parameters was investigated in depth. A combination of diagnostics was used to select an optimum, 7-factor model using one complete year of daily data with pointwise measurement uncertainties. The factors included 1) a wintertime/methoxyphenol factor, 2) an EC/sterane factor, 3) a nitrate/polycyclic aromatic hydrocarbon (PAH) factor, 4) a summertime/selective aliphatic factor, 5) an n-alkane factor, 6) a middle-oxygenated PAH/alkanoic acid factor and 7) an inorganic ion factor. These seven factors were qualitatively linked with known PM 2.5 emission sources with varying degrees of confidence. Mass apportionment using the 7-factor model revealed the contribution of each factor to the mass of OC, EC, nitrate and sulfate. On an annual basis, the majority of OC and EC

  11. Source Apportionment Using Positive Matrix Factorization on Daily Measurements of Inorganic and Organic Speciated PM2.5

    PubMed Central

    Dutton, Steven J.; Vedal, Sverre; Piedrahita, Ricardo; Milford, Jana B.; Miller, Shelly L.; Hannigan, Michael P.

    2012-01-01

    Particulate matter less than 2.5 microns in diameter (PM2.5) has been linked with a wide range of adverse health effects. Determination of the sources of PM2.5 most responsible for these health effects could lead to improved understanding of the mechanisms of such effects and more targeted regulation. This has provided the impetus for the Denver Aerosol Sources and Health (DASH) study, a multi-year source apportionment and health effects study relying on detailed inorganic and organic PM2.5 speciation measurements. In this study, PM2.5 source apportionment is performed by coupling positive matrix factorization (PMF) with daily speciated PM2.5 measurements including inorganic ions, elemental carbon (EC) and organic carbon (OC), and organic molecular markers. A qualitative comparison is made between two models, PMF2 and ME2, commonly used for solving the PMF problem. Many previous studies have incorporated chemical mass balance (CMB) for organic molecular marker source apportionment on limited data sets, but the DASH data set is large enough to use multivariate factor analysis techniques such as PMF. Sensitivity of the PMF2 and ME2 models to the selection of speciated PM2.5 components and model input parameters was investigated in depth. A combination of diagnostics was used to select an optimum, 7-factor model using one complete year of daily data with pointwise measurement uncertainties. The factors included 1) a wintertime/methoxyphenol factor, 2) an EC/sterane factor, 3) a nitrate/polycyclic aromatic hydrocarbon (PAH) factor, 4) a summertime/selective aliphatic factor, 5) an n-alkane factor, 6) a middle oxygenated PAH/alkanoic acid factor and 7) an inorganic ion factor. These seven factors were qualitatively linked with known PM2.5 emission sources with varying degrees of confidence. Mass apportionment using the 7-factor model revealed the contribution of each factor to the mass of OC, EC, nitrate and sulfate. On an annual basis, the majority of OC and EC mass

  12. Chemical speciation and source apportionment of fine particulate matter in Santiago, Chile, 2013.

    PubMed

    Villalobos, Ana M; Barraza, Francisco; Jorquera, Héctor; Schauer, James J

    2015-04-15

    Santiago is one of the largest cities in South America and has experienced high fine particulate matter (PM2.5) concentrations in fall and winter months for decades. To better understand the sources of fall and wintertime pollution in Santiago, PM2.5 samples were collected for 24 h every weekday from March to October 2013 for chemical analysis. Samples were analyzed for mass, elemental carbon (EC), organic carbon (OC), water soluble organic carbon (WSOC), water soluble nitrogen (WSTN), secondary inorganic ions, and particle-phase organic tracers for source apportionment. Selected samples were analyzed as monthly composites for organic tracers. PM2.5 concentrations were considerably higher in the coldest months (June-July), averaging (mean ± standard deviation) 62±15 μg/m(3) in these two months. Average fine particle mass concentration during the study period was 40±20 μg/m(3). Organic matter during the peak winter months was the major component of fine particles comprising around 70% of the particle mass. Source contributions to OC were calculated using organic molecular markers and a chemical mass balance (CMB) receptor model. The four combustion sources identified were wood smoke, diesel engine emission, gasoline vehicles, and natural gas. Wood smoke was the predominant source of OC, accounting for 58±42% of OC in fall and winter. Wood smoke and nitrate were the major contributors to PM2.5. In fall and winter, wood smoke accounted for 9.8±7.1 μg/m(3) (21±15%) and nitrate accounted for 9.1±4.8 μg/m(3) (20±10%) of fine PM. The sum of secondary inorganic ions (sulfate, nitrate, and ammonium) represented about 30% of PM2.5 mass. Secondary organic aerosols contributed only in warm months, accounting for about 30% of fine PM during this time.

  13. Source apportionment of arsenic in atmospheric dust fall out in an urban residential area, Raipur, Central India

    NASA Astrophysics Data System (ADS)

    Balakrishna, G.; Pervez, S.; Bisht, D. S.

    2011-06-01

    The components and quantities of atmospheric dust fallout have been reported to be the pollution indicator of large urban areas. The multiplicity and complexity of sources of atmospheric dusts in urban regions has put forward the need of source apportionment of these sources indicating their contribution to specific environmental receptor. The study presented here is focused on investigation of source contribution estimates of Arsenic in urban dust fallout in an urban-industrial area, Raipur, India. Source-receptor based representative sampling plan using longitudinal study design has been adopted. Six sampling sites have been identified on the basis of land use for development plan of anthropogenic activities and factors related to the transportation and dispersion pattern of atmospheric dusts. Source apportionment has been done using Chemical Mass Balance (CMB 8). Good fit parameters and relative source contribution has been analyzed and documented. Dominance of coal fired industries sources on arsenic levels measured at selected ambient residential receptors compared to line sources has been observed. Road-traffic has shown highest contribution of dust at indoor houses and out door-street automobile exhaust has shows highest contribution for arsenic. The results of CMB output and regression data of source-receptor dust matrices have shown comparable pattern.

  14. Source regional contributions to PM2.5 in a megacity in China using an advanced source regional apportionment method.

    PubMed

    Tian, Ying-Ze; Chen, Gang; Wang, Hai-Ting; Huang-Fu, Yan-Qi; Shi, Guo-Liang; Han, Bo; Feng, Yin-Chang

    2016-03-01

    To quantify contributions of individual source categories from diverse regions to PM2.5, PM2.5 samples were collected in a megacity in China and analyzed through a newly developed source regional apportionment (SRA) method. Levels, compositions and seasonal variations of speciated PM2.5 dataset were investigated. Sources were determined by Multilinear Engine 2 (ME2) model, and results showed that the PM2.5 in Tianjin was mainly influenced by secondary sulphate & secondary organic carbon SOC (percent contribution of 26.2%), coal combustion (24.6%), crustal dust & cement dust (20.3%), secondary nitrate (14.9%) and traffic emissions (14.0%). The SRA method showed that northwest region R2 was the highest regional contributor to secondary sources, with percent contributions to PM2.5 being 9.7% for secondary sulphate & SOC and 6.0% for secondary nitrates; the highest coal combustion was from local region R1 (6.2%) and northwest R2 (8.0%); the maximum contributing region to crustal & cement dust was southeast region R4 (5.0%); and contributions of traffic emissions were relatively spatial homogeneous. The seasonal variation of regional source contributions was observed: in spring, the crustal and cement dust contributed a higher percentage and the R4 was an important contributor; the secondary process attributed an increase fraction in summer; the mixed coal combustion from southwest R5 enhanced in autumn.

  15. Source apportionment of atmospheric water over East Asia - a source tracer study in CAM5.1

    NASA Astrophysics Data System (ADS)

    Pan, Chen; Zhu, Bin; Gao, Jinhui; Kang, Hanqing

    2017-02-01

    The atmospheric water tracer (AWT) method is implemented in the Community Atmosphere Model version 5.1 (CAM5.1) to quantitatively identify the contributions of various source regions to precipitation and water vapour over East Asia. Compared to other source apportionment methods, the AWT method was developed based on detailed physical parameterisations, and can therefore trace the behaviour of atmospheric water substances directly and exactly. According to the simulation, the northern Indian Ocean (NIO) is the dominant oceanic moisture source region for precipitation over the Yangtze River valley (YRV) and southern China (SCN) in summer, while the north-western Pacific (NWP) dominates during other seasons. Evaporation over the South China Sea (SCS) is responsible for only 2.7-3.7 % of summer precipitation over the YRV and SCN. In addition, the Indo-China Peninsula is an important terrestrial moisture source region (annual contribution of ˜ 10 %). The overall relative contribution of each source region to the water vapour amount is similar to the corresponding contribution to precipitation over the YRV and SCN. A case study for the SCS shows that only a small part ( ≤ 5.5 %) of water vapour originates from local evaporation, whereas much more water vapour is supplied by the NWP and NIO. In addition, because evaporation from the SCS represents only a small contribution to the water vapour over the YRV and SCN in summer, the SCS mainly acts as a water vapour transport pathway where moisture from the NIO and NWP meet.

  16. Measurement and apportionment of radon source terms for modeling indoor environments

    SciTech Connect

    Harley, N.H.

    1992-01-01

    During the present 2 1/2 year contract period, we have made significant Progress in modeling the source apportionment of indoor [sup 222]Rn and in [sup 222]Rn decay product dosimetry. Two additional areas were worked on which we believe are useful for the DOE Radon research Program. One involved an analysis of the research house data, grouping the hourly house [sup 222]Rn measurements into 2 day, 7 day and 90 day intervals to simulate the response of passive monitors. Another area requiring some attention resulted in a publication of 3 years of our indoor/outdoor measurements in a high-rise apartment. Little interest has been evinced in apartment measurements yet 20% of the US population lives in multiple-family dwellings, not in contact with the ground. These data together with a summary of all other published data on apartments showed that apartments have only about 50% greater [sup 222]Rn concentration than the measured outdoor [sup 222]Rn. Apartment dwellers generally represent a low risk group regarding [sup 222]Rn exposure. The following sections describe the main projects in some detail.

  17. Receptor model-based source apportionment of particulate pollution in Hyderabad, India.

    PubMed

    Guttikunda, Sarath K; Kopakka, Ramani V; Dasari, Prasad; Gertler, Alan W

    2013-07-01

    Air quality in Hyderabad, India, often exceeds the national ambient air quality standards, especially for particulate matter (PM), which, in 2010, averaged 82.2 ± 24.6, 96.2 ± 12.1, and 64.3 ± 21.2 μg/m(3) of PM10, at commercial, industrial, and residential monitoring stations, respectively, exceeding the national ambient standard of 60 μg/m(3). In 2005, following an ordinance passed by the Supreme Court of India, a source apportionment study was conducted to quantify source contributions to PM pollution in Hyderabad, using the chemical mass balance (version 8.2) receptor model for 180 ambient samples collected at three stations for PM10 and PM2.5 size fractions for three seasons. The receptor modeling results indicated that the PM10 pollution is dominated by the direct vehicular exhaust and road dust (more than 60%). PM2.5 with higher propensity to enter the human respiratory tracks, has mixed sources of vehicle exhaust, industrial coal combustion, garbage burning, and secondary PM. In order to improve the air quality in the city, these findings demonstrate the need to control emissions from all known sources and particularly focus on the low-hanging fruits like road dust and waste burning, while the technological and institutional advancements in the transport and industrial sectors are bound to enhance efficiencies. Andhra Pradesh Pollution Control Board utilized these results to prepare an air pollution control action plan for the city.

  18. Source apportionment and water solubility of metals in size segregated particles in urban environments.

    PubMed

    Jiang, Sabrina Yanan; Kaul, Daya S; Yang, Fenhuan; Sun, Li; Ning, Zhi

    2015-11-15

    Metals in atmospheric particulate matter (PM) have been associated with various adverse health effects. Different factors contributing to the characterization and distribution of atmospheric metals in urban environments lead to uncertainty of the understanding of their impact on public health. However, few studies have provided a comprehensive picture of the spatial and seasonal variability of metal concentration, solubility and size distribution, all of which have important roles in their contribution to health effects. This study presents an experimental investigation on the characteristics of metals in PM2.5 and coarse PM in two seasons from four urban sites in Hong Kong. The PM samples were extracted separately with aqua regia and water, and a total of sixteen elements were analyzed using ICP-MS and ICP-OES to determine the size segregated concentration and solubility of metals. The concentrations of major metals were distributed in similar patterns with the same order of magnitude among different urban sites. Source apportionment using Positive Matrix Factorization (PMF) indicated that three sources namely road dust, vehicular exhaust and ship emission are major contributors to the urban atmospheric metal concentrations in Hong Kong with distinctly different profiles between coarse PM and PM2.5 fractions. The individual metals were assigned to different sources, consistent with literature documentation, except potassium emerging with substantial contribution from vehicle exhaust emission. Literature data from past studies on both local and other cities were compared to the results from the present study to investigate the impact of different emission sources and control policies on metal distribution in urban atmosphere. A large variation of solubility among the metals reflected that the majority of metals in PM2.5 were more soluble than those in coarse PM indicating size dependent chemical states of metals. The data from this study provides a rich dataset of

  19. Open air mineral treatment operations and ambient air quality: assessment and source apportionment.

    PubMed

    Escudero, M; Alastuey, A; Moreno, T; Querol, X; Pérez, P

    2012-11-01

    We present a methodology for evaluating and quantifying the impact of inhalable mineral dust resuspension close to a potentially important industrial point source, in this case an open air plant producing sand, flux and kaolin in the Capuchinos district of Alcañiz (Teruel, NE Spain). PM(10) levels at Capuchinos were initially high (42 μg m(-3) as the annual average with 91 exceedances of the EU daily limit value during 2007) but subsequently decreased (26 μg m(-3) with 16 exceedances in 2010) due to a reduced demand for minerals from the ceramic industry and construction sector during the first stages of the economic crisis. Back trajectory and local wind pattern analyses revealed only limited contribution from exotic PM sources such as African dust intrusions whereas there was clearly a strong link with the mineral stockpiles of the local industry. This link was reinforced by chemical and mineral speciation and source apportionment analysis which showed a dominance of mineral matter (sum of CO(3)(2-), SiO(2), Al(2)O(3), Ca, Fe, K, Mg, P, and Ti: mostly aluminosilicates) which in 2007 contributed 76% of the PM(10) mass (44 μg m(-3) on average). The contribution from Secondary Inorganic Aerosols (SIA, sum of SO(4)(2-), NO(3)(-) and NH(4)(+)) reached 8.4 μg m(-3), accounting for 14% of the PM(10) mass, similar to the amount of calcareous road dust estimated to be present (8 μg m(-3); 13%). Organic matter and elemental carbon contributed 5.3 μg m(-3) (9%) whereas marine aerosol (Na + Cl) levels were minor with an average concentration of 0.4 μg m(-3) (1% of the PM(10) mass). Finally, chemical and mineralogical analysis of stockpile samples and comparison with filter samples confirmed the local industry to be the major source of ambient PM(10) in the area.

  20. Overview of receptor-based source apportionment studies for speciated atmospheric mercury

    NASA Astrophysics Data System (ADS)

    Cheng, I.; Xu, X.; Zhang, L.

    2015-07-01

    Receptor-based source apportionment studies of speciated atmospheric mercury are not only concerned with source contributions but also with the influence of transport, transformation, and deposition processes on speciated atmospheric mercury concentrations at receptor locations. Previous studies applied multivariate receptor models including principal components analysis and positive matrix factorization, and back trajectory receptor models including potential source contribution function, gridded frequency distributions, and concentration-back trajectory models. Combustion sources (e.g., coal combustion, biomass burning, and vehicular, industrial and waste incineration emissions), crustal/soil dust, and chemical and physical processes, such as gaseous elemental mercury (GEM) oxidation reactions, boundary layer mixing, and GEM flux from surfaces were inferred from the multivariate studies, which were predominantly conducted at receptor sites in Canada and the US. Back trajectory receptor models revealed potential impacts of large industrial areas such as the Ohio River valley in the US and throughout China, metal smelters, mercury evasion from the ocean and the Great Lakes, and free troposphere transport on receptor measurements. Input data and model parameters specific to atmospheric mercury receptor models are summarized and model strengths and weaknesses are also discussed. Multivariate models are suitable for receptor locations with intensive air monitoring because they require long-term collocated and simultaneous measurements of speciated atmospheric Hg and ancillary pollutants. The multivariate models provide more insight about the types of Hg emission sources and Hg processes that could affect speciated atmospheric Hg at a receptor location, whereas back trajectory receptor models are mainly ideal for identifying potential regional Hg source locations impacting elevated Hg concentrations. Interpretation of the multivariate model output to sources can be

  1. Source apportionment of carbonaceous aerosol in Sao Paulo using 13C and 14C measurements

    NASA Astrophysics Data System (ADS)

    Oyama, Beatriz; Andrade, Maria de Fatima; Holzinger, Rupert; Röckmann, Thomas; Meijer, Harro A. J.; Dusek, Ulrike

    2016-04-01

    The Metropolitan Area of Sao Paulo is affected by high aerosol concentrations, which contain a large fraction of organic material. Up to date, not much is known about the composition and origin of the organic aerosol in this city. We present the first source apportionment of the carbonaceous aerosol fraction in Sao Paulo, using stable (13C) and radioactive carbon isotopes (14C). 14C provides a clear-cut distinction between fossil sources, which contain no 14C, and contemporary sources such as biofuels, biomass burning, or biogenic sources, which contain a typical contemporary 14C/12C ratio. 13C can be used to distinguish C3 plants, such as maize and sugarcane, from C4 plants. This can help to identify a possible impact of sugarcane field burning in the rural areas of Sao Paulo State on the aerosol carbon in the city. In the first part of the study, we compare two tunnel studies: Tunnel 1 is frequented only by light duty vehicles, which run mainly on mixtures of gasoline with ethanol (gasohol, 25% ethanol and 85% gasoline) or hydrated ethanol (5% water and 95% ethanol). Tunnel 2 contains a significant fraction of heavy-duty diesel vehicles, and therefore the fraction of biofuels in the average fleet is lower. Comparison of 14C in organic and elemental carbon (OC and EC) shows that in both tunnels there is no significant contribution of biofuels to EC. Combusting ethanol-gasoline fuels in a vehicle engine does apparently not result in significant EC formation from ethanol. Biofuels contribute around 45% to OC in Tunnel 1 an only 20% in Tunnel 2, reflecting a strong impact of diesel vehicles in Tunnel 2. In the second part of the study we conduct a source apportionment of ambient aerosol carbon collected in a field study during winter (July-August) 2012. Ambient EC has two main sources, vehicular emissions and biomass burning. We estimate a contribution of vehicular sources to EC of roughly 90% during weekdays and 80% during weekends, using the 14C values measured in

  2. Seasonal variability and source apportionment of volatile organic compounds (VOCs) in the Paris megacity (France)

    NASA Astrophysics Data System (ADS)

    Baudic, Alexia; Gros, Valérie; Sauvage, Stéphane; Locoge, Nadine; Sanchez, Olivier; Sarda-Estève, Roland; Kalogridis, Cerise; Petit, Jean-Eudes; Bonnaire, Nicolas; Baisnée, Dominique; Favez, Olivier; Albinet, Alexandre; Sciare, Jean; Bonsang, Bernard

    2016-09-01

    Within the framework of air quality studies at the megacity scale, highly time-resolved volatile organic compound (C2-C8) measurements were performed in downtown Paris (urban background sites) from January to November 2010. This unique dataset included non-methane hydrocarbons (NMHCs) and aromatic/oxygenated species (OVOCs) measured by a GC-FID (gas chromatograph with a flame ionization detector) and a PTR-MS (proton transfer reaction - mass spectrometer), respectively. This study presents the seasonal variability of atmospheric VOCs being monitored in the French megacity and their various associated emission sources. Clear seasonal and diurnal patterns differed from one VOC to another as the result of their different origins and the influence of environmental parameters (solar radiation, temperature). Source apportionment (SA) was comprehensively conducted using a multivariate mathematical receptor modeling. The United States Environmental Protection Agency's positive matrix factorization tool (US EPA, PMF) was used to apportion and quantify ambient VOC concentrations into six different sources. The modeled source profiles were identified from near-field observations (measurements from three distinct emission sources: inside a highway tunnel, at a fireplace and from a domestic gas flue, hence with a specific focus on road traffic, wood-burning activities and natural gas emissions) and hydrocarbon profiles reported in the literature. The reconstructed VOC sources were cross validated using independent tracers such as inorganic gases (NO, NO2, CO), black carbon (BC) and meteorological data (temperature). The largest contributors to the predicted VOC concentrations were traffic-related activities (including motor vehicle exhaust, 15 % of the total mass on the annual average, and evaporative sources, 10 %), with the remaining emissions from natural gas and background (23 %), solvent use (20 %), wood-burning (18 %) and a biogenic source (15 %). An important finding of

  3. Wintertime aerosol chemical composition and source apportionment of the organic fraction in the metropolitan area of Paris

    NASA Astrophysics Data System (ADS)

    Crippa, M.; DeCarlo, P. F.; Slowik, J. G.; Mohr, C.; Heringa, M. F.; Chirico, R.; Poulain, L.; Freutel, F.; Sciare, J.; Cozic, J.; Di Marco, C. F.; Elsasser, M.; Nicolas, J. B.; Marchand, N.; Abidi, E.; Wiedensohler, A.; Drewnick, F.; Schneider, J.; Borrmann, S.; Nemitz, E.; Zimmermann, R.; Jaffrezo, J.-L.; Prévôt, A. S. H.; Baltensperger, U.

    2013-01-01

    The effect of a post-industrial megacity on local and regional air quality was assessed via a month-long field measurement campaign in the Paris metropolitan area during winter 2010. Here we present source apportionment results from three aerosol mass spectrometers and two aethalometers deployed at three measurement stations within the Paris region. Submicron aerosol composition is dominated by the organic fraction (30-36%) and nitrate (28-29%), with lower contributions from sulfate (14-16%), ammonium (12-14%) and black carbon (7-13%). Organic source apportionment was performed using positive matrix factorization, resulting in a set of organic factors corresponding both to primary emission sources and secondary production. The dominant primary sources are traffic (11-15% of organic mass), biomass burning (13-15%) and cooking (up to 35% during meal hours). Secondary organic aerosol contributes more than 50% to the total organic mass and includes a highly oxidized factor from indeterminate and/or diverse sources and a less oxidized factor related to wood burning emissions. Black carbon was apportioned to traffic and wood burning sources using a model based on wavelength-dependent light absorption of these two combustion sources. The time series of organic and black carbon factors from related sources were strongly correlated. The similarities in aerosol composition, total mass and temporal variation between the three sites suggest that particulate pollution in Paris is dominated by regional factors, and that the emissions from Paris itself have a relatively low impact on its surroundings.

  4. Integrating Source Apportionment Tracers into a Bottom-up Inventory of Methane Emissions in the Barnett Shale Hydraulic Fracturing Region.

    PubMed

    Townsend-Small, Amy; Marrero, Josette E; Lyon, David R; Simpson, Isobel J; Meinardi, Simone; Blake, Donald R

    2015-07-07

    A growing dependence on natural gas for energy may exacerbate emissions of the greenhouse gas methane (CH4). Identifying fingerprints of these emissions is critical to our understanding of potential impacts. Here, we compare stable isotopic and alkane ratio tracers of natural gas, agricultural, and urban CH4 sources in the Barnett Shale hydraulic fracturing region near Fort Worth, Texas. Thermogenic and biogenic sources were compositionally distinct, and emissions from oil wells were enriched in alkanes and isotopically depleted relative to natural gas wells. Emissions from natural gas production varied in δ(13)C and alkane ratio composition, with δD-CH4 representing the most consistent tracer of natural gas sources. We integrated our data into a bottom-up inventory of CH4 for the region, resulting in an inventory of ethane (C2H6) sources for comparison to top-down estimates of CH4 and C2H6 emissions. Methane emissions in the Barnett are a complex mixture of urban, agricultural, and fossil fuel sources, which makes source apportionment challenging. For example, spatial heterogeneity in gas composition and high C2H6/CH4 ratios in emissions from conventional oil production add uncertainty to top-down models of source apportionment. Future top-down studies may benefit from the addition of δD-CH4 to distinguish thermogenic and biogenic sources.

  5. GIS-based source identification and apportionment of diffuse water pollution: perfluorinated compound pollution in the Tokyo Bay basin.

    PubMed

    Zushi, Yasuyuki; Masunaga, Shigeki

    2011-11-01

    To efficiently reduce perfluorinated compound (PFC) pollution, it is important to have an understanding of PFC sources and their contribution to the pollution. In this study, source identification of diffuse water pollution by PFCs was conducted using a GIS-based approach. Major components of the source identification were collection of the monitoring data and preparation of the corresponding geographic information that was extracted from a constructed GIS database. The spatially distributed pollution factors were then explored by multiple linear regression analysis, after which they were visually expressed using GIS. Among the 35 PFC homologues measured in a survey of the Tokyo Bay basin, 18 homologues were analyzed. Pollution by perfluorooctane sulfonate (PFOS) was explained well by the percentage of arterial traffic area in the basin, and the 84% variance of the measured PFOS concentration was explained by two geographic variables, arterial traffic area and population. Source apportionment between point and nonpoint sources was conducted based on the results of the analysis. The contribution of PFOS from nonpoint sources was comparable to that from point sources in several major rivers flowing into Tokyo Bay. Source identification and apportionment using the GIS-based approach was shown to be effective, especially for ubiquitous types of pollution, such as PFC pollution.

  6. Evaluation of Particulate Matter Source Apportionment Forecasts during the MAPS-Seoul Field Campaign

    NASA Astrophysics Data System (ADS)

    Bae, C.; Kim, S.; Kim, H. C.; Kim, B. U.

    2015-12-01

    We report forecasting model performance analysis results of Comprehensive Air quality Model with extensions (CAMx) simulation evaluated with flight measurements during Megacity Air Pollution Studies-Seoul (MAPS-Seoul) field campaign. The primary focus of this study is two-fold: (1) the air quality forecasting model performance for O3, PM10/2.5 and their precursors over the Yellow Sea to measure the model's ability to account for the transport process and (2) the utilization of modeled source-receptor relationship to understand the root of systematic model under-prediction for PM10 and PM2.5 forecasts. MAPS-Seoul, conducted in the Seoul Metropolitan Area (SMA) in the summer of 2015, was an integrated research program covering ground monitoring and aloft measurement with aircrafts. To support this field campaign, air quality forecasting was performed with Weather Research and Forecasting (WRF) - Sparse Matrix Operator Kernel Emissions (SMOKE) - CAMx modeling framework. WRF model simulations initialized with National Centers for Environmental Prediction Global Forecasting System (NOAA/NCEP-GFS) were prepared for daily meteorological forecasts. Emission inventories used in this study are Model Inter-Comparison Study-Asia (MICS-Asia) 2010 for Asia and Clean Air Policy Support System (CAPSS) 2010 for South Korea. Simulated PM10 concentrations were evaluated with observed PM10 concentrations at ground monitoring sites of the AirKorea network in SMA. During the campaign period, average simulated PM10 concentrations showed significant underprediction, over 30% (~35 ㎍/㎥) lower than those observed at sites. To examine source-receptor relationship as a way to identify the cause of underprediction, we ran CAMx with Particulate matter Source Apportionment Technology (PSAT). The air quality forecasting model is based on the with 27-km horizontal grid resolution over Northeast Asia.

  7. Successful application of lead isotopes in source apportionment, legal proceedings, remediation and monitoring

    SciTech Connect

    Gulson, Brian; Korsch, Michael; Winchester, Wayne; Devenish, Matthew; Hobbs, Thad; Main, Cleve; Smith, Gerard; Rosman, Kevin; Howearth, Lynette; Burn-Nunes, Laurie; Seow, Jimmy; Oxford, Cameron; Yun, Gracie; Gillam, Lindsay; Crisp, Michelle

    2012-01-15

    In late 2006, the seaside community in Esperance Western Australia was alerted to thousands of native bird species dying. The source of the lead (Pb) was determined by Pb isotopes to derive from the handling of Pb carbonate concentrate through the Port, which began in July 2005. Concern was expressed for the impact of this on the community. Our objectives were to employ Pb isotope ratios to evaluate the source of Pb in environmental samples for use in legal proceedings, and for use in remediation and monitoring. Isotope measurements were undertaken of bird livers, plants, drinking water, soil, harbour sediments, air, bulk ceiling dust, gutter sludge, surface swabs and blood. The unique lead isotopic signature of the contaminating Pb carbonate enabled diagnostic apportionment of lead in samples. Apart from some soil and water samples, the proportion of contaminating Pb was >95% in the environmental samples. Lead isotopes were critical in resolving legal proceedings, are being used in the remediation of premises, were used in monitoring of workers involved in the decontamination of the storage facility, and monitoring transport of the concentrate through another port facility. Air samples show the continued presence of contaminant Pb, more than one year after shipping of concentrate ceased, probably arising from dust resuspension. Brief details of the comprehensive testing and cleanup of the Esperance community are provided along with the role of the Community. Lead isotopic analyses can provide significant benefits to regulatory agencies, interested parties, and the community where the signature is able to be characterised with a high degree of certainty. - Highlights: Black-Right-Pointing-Triangle Lead carbonate concentrate. Black-Right-Pointing-Triangle Successful use of Pb isotopes in identifying sources of Pb arising from transport and shipping. Black-Right-Pointing-Triangle Use of Pb isotopes in legal proceedings and their use in cleanup of residences. Black

  8. Source apportionment of speciated PM10 in the United Kingdom in 2008: Episodes and annual averages

    NASA Astrophysics Data System (ADS)

    Redington, A. L.; Witham, C. S.; Hort, M. C.

    2016-11-01

    The Lagrangian atmospheric dispersion model NAME (Numerical Atmospheric-dispersion Modelling Environment), has been used to simulate the formation and transport of PM10 over North-West Europe in 2008. The model has been evaluated against UK measurement data and been shown to adequately represent the observed PM10 at rural and urban sites on a daily basis. The Lagrangian nature of the model allows information on the origin of pollutants (and hence their secondary products) to be retained to allow attribution of pollutants at receptor sites back to their sources. This source apportionment technique has been employed to determine whether the different components of the modelled PM10 have originated from UK, shipping, European (excluding the UK) or background sources. For the first time this has been done to evaluate the composition during periods of elevated PM10 as well as the annual average composition. The episode data were determined by selecting the model data for each hour when the corresponding measurement data was >50 μg/m3. All the modelled sites show an increase in European pollution contribution and a decrease in the background contribution in the episode case compared to the annual average. The European contribution is greatest in southern and eastern parts of the UK and decreases moving northwards and westwards. Analysis of the speciated attribution data over the selected sites reveals that for 2008, as an annual average, the top three contributors to total PM10 are UK primary PM10 (17-25%), UK origin nitrate aerosol (18-21%) and background PM10 (11-16%). Under episode conditions the top three contributors to modelled PM10 are UK origin nitrate aerosol (12-33%), European origin nitrate aerosol (11-19%) and UK primary PM10 (12-18%).

  9. Organic composition and source apportionment of fine aerosol at Monterrey, Mexico, based on organic markers

    NASA Astrophysics Data System (ADS)

    Mancilla, Y.; Mendoza, A.; Fraser, M. P.; Herckes, P.

    2016-01-01

    attribution results obtained using the CMB (chemical mass balance) model indicate that emissions from motor vehicle exhausts are the most important, accounting for the 64 % of the PM2.5, followed by meat-cooking operations with 31 % The vegetative detritus and biomass burning had the smallest contribution (2.2 % of the PM2.5). To our knowledge, this is only the second study to explore the organic composition and source apportionment of fine organic aerosol based on molecular markers in Mexico and the first for the MMA. Particularly molecular marker were quantified by solvent extraction with dichloromethane, derivatization, and gas chromatography with mass spectrometry (GC/MS).

  10. Development, testing, and application of a new Multi-Receptor (MURA) Trajectory Source Apportionment (TSA) method

    NASA Astrophysics Data System (ADS)

    Lee, Stephanie J.

    Trajectory Source Apportionment (TSA) methods are statistical techniques used to identify sources of pollution at a sampling site (receptor). TSA methods have traditionally been applied to a single receptor (Ashbaugh et al., 1985; Seibert et al., 1994; Lui et al., 2003) with some exploration of using more than one receptor (Stohl, 1996; Zeng and Hopke, 1989). A new Multi-Receptor (MURA) method was developed here. It utilizes a two step process to first identify Potential Source Regions (PSRs), and then examine them to see how often they affect each receptor. The MURA method was first tested against the conditional probability method developed by Ashbaugh et al. (1985) to determine each method's ability to detect known sources. Two artificial data sets were used; one containing a single source and one that contained four sources. The MURA method outperformed the conditional probability method. Next, the MURA method was compared to an improved version of the conditional probability method (SIRA). This test utilized three sets of artificial data in the western and eastern U.S. Although the SIRA method was an improvement over the conditional probability method, the MURA method still performed better in the four-source simulation located in the western United States. In the two eastern simulations both the MURA and SIRA methods performed similarly. The third test evaluated the impact of trajectory starting heights from 10m to 500m on the MURA method using the three simulations from the SIRA comparison. In the western simulation, the starting height had little to no impact on the accuracy of the method. In the two eastern simulations, the 10m, 50m, and 250m starting heights performed more consistently over both simulations. The MURA method was then applied to two groups of IMPROVE receptors to identify sources of sulfate and nitrate. The southwest, the western Great Plains, and the eastern Midwest affect the south central United States group for high sulfate or nitrate

  11. Source apportionment of polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) in ambient air of an industrial region in Turkey

    NASA Astrophysics Data System (ADS)

    Aydin, Yagmur Meltem; Kara, Melik; Dumanoglu, Yetkin; Odabasi, Mustafa; Elbir, Tolga

    2014-11-01

    Source apportionment is generally applied to a time series of data collected at a single site. However, in a complex airshed containing several different sources, it may be helpful to collect samples from multiple sites to ensure that some of them have low contributions from specific sources, thus the boundaries can be properly defined. Ambient air polycyclic aromatic hydrocarbon (PAH) and polychlorinated biphenyls (PCB) samples (n = 160) were collected at 40 sites during four seasons (summer, fall, winter, and spring) between July 2009 and April 2010 in the heavily industrialized Aliaga region in Turkey to investigate their spatial, seasonal variations and to identify possible PAH and PCB sources. The newest version of EPA PMF (V5.0) having the capability of handling multiple site data was used for source apportionment. Five PAH sources were identified as biomass and coal combustion, iron-steel production, unburned crude oil and petroleum products, and diesel and gasoline exhaust emissions with contributions of 40, 27, 27, 3, and 3%, respectively. The sources of PCBs were identified as iron-steel production (consisting of steel-making and ship breaking activities), coal and wood combustion, and evaporative emissions from technical PCB mixtures with contributions of 57, 31, and 12%, respectively.

  12. Improved source apportionment and speciation of low-volume particulate matter samples.

    PubMed

    Schauer, James J; Majestic, Brian J; Sheesley, Rebecca J; Shafer, Martin M; Deminter, Jeffrey T; Mieritz, Mark

    2010-12-01

    New chemical analysis methods for the characterization of atmospheric particulate matter (PM)* samples were developed and demonstrated in order to expand the number of such methods for use in future health studies involving PM. Three sets of methods were, developed, for the analysis (1) of organic tracer compounds in low-volume personal exposure samples (for source apportionment), (2) of trace metals and other trace elements in low-volume personal exposure samples, and (3) of the speciation of the oxidation states of water-soluble iron (Fe), manganese (Mn), and chromium (Cr) in PM samples. The development of the second set of methods built on previous work by the project team, which had in the past used similar methods in atmospheric source apportionment studies. The principal challenges in adapting these methods to the analysis of personal exposure samples were the improvement of detection limits (DLs) and control of the low-level contamination that can compromise personal exposure samples. A secondary goal of our development efforts was to reduce the cost and complexity of the three sets of methods in order to help facilitate their broader use in future health studies. The goals of the project were achieved, and the ability to integrate the methods into existing health studies was demonstrated by way of conducting two pilot studies. The first study involved analysis of trace elements in size-resolved PM samples that had been collected to represent study subjects' personal exposures along with simultaneous measures of indoor and outdoor PM concentrations. The second study involved analysis of the speciation of organic tracer compounds in personal exposure samples, indoor samples, and outdoor samples in order to understand the diesel PM exposure of study subjects in various job classifications in an occupational setting. Both pilot studies used existing samples from. large multi-year health studies and were intended to demonstrate the feasibility and value of using

  13. Aerosol source apportionment from 1-year measurements at the CESAR tower in Cabauw, the Netherlands

    NASA Astrophysics Data System (ADS)

    Schlag, Patrick; Kiendler-Scharr, Astrid; Blom, Marcus Johannes; Canonaco, Francesco; Sebastiaan Henzing, Jeroen; Moerman, Marcel; Prévôt, André Stephan Henry; Holzinger, Rupert

    2016-07-01

    Intensive measurements of submicron aerosol particles and their chemical composition were performed with an Aerosol Chemical Speciation Monitor (ACSM) at the Cabauw Experimental Site for Atmospheric Research (CESAR) in Cabauw, the Netherlands, sampling at 5 m height above ground. The campaign lasted nearly 1 year from July 2012 to June 2013 as part of the EU-FP7-ACTRIS project (Q-ACSM Network). Including equivalent black carbon an average particulate mass concentration of 9.50 µg m-3 was obtained during the whole campaign with dominant contributions from ammonium nitrate (45 %), organic aerosol (OA, 29 %), and ammonium sulfate (19 %). There were 12 exceedances of the World Health Organization (WHO) PM2.5 daily mean limit (25 µg m-3) observed at this rural site using PM1 instrumentation only. Ammonium nitrate and OA represented the largest contributors to total particulate matter during periods of exceedance. Source apportionment of OA was performed season-wise by positive matrix factorization (PMF) using the multilinear engine 2 (ME-2) controlled via the source finder (SoFi). Primary organic aerosols were attributed mainly to traffic (8-16 % contribution to total OA, averaged season-wise) and biomass burning (0-23 %). Secondary organic aerosols (SOAs, 61-84 %) dominated the organic fraction during the whole campaign, particularly on days with high mass loadings. A SOA factor which is attributed to humic-like substances (HULIS) was identified as a highly oxidized background aerosol in Cabauw. This shows the importance of atmospheric aging processes for aerosol concentration at this rural site. Due to the large secondary fraction, the reduction of particulate mass at this rural site is challenging on a local scale.

  14. Source apportionment of elevated wintertime PAHs by compound-specific radiocarbon analysis

    NASA Astrophysics Data System (ADS)

    Sheesley, R. J.; Kruså, M.; Krecl, P.; Johansson, C.; Gustafsson, Ã.-.

    2008-12-01

    Natural abundance radiocarbon analysis facilitates distinct source apportionment between contemporary biomass/biofuel (14C "alive") versus fossil fuel (14C "dead") combustion. Here, the first compound-specific radiocarbon analysis (CSRA) of atmospheric polycylic aromatic hydrocarbons (PAHs) was demonstrated for a set of samples collected in Lycksele, Sweden a small town with frequent episodes of severe atmospheric pollution in the winter. Renewed interest in residential wood combustion means than this type of seasonal pollution is of increasing concern in many areas. Five individual/paired PAH isolates from three pooled fortnight-long filter collections were analyzed by CSRA: phenanthrene, fluoranthene, pyrene, benzo[b+k]fluoranthene and indeno[cd]pyrene plus benzo[ghi]perylene; phenanthrene was the only compound also analyzed in the gas phase. The measured Δ14C for PAHs spanned from -138.3‰ to 58.0‰. A simple isotopic mass balance model was applied to estimate the fraction biomass (fbiomass) contribution that was constrained to a range of 71% for indeno[cd]pyrene+benzo[ghi]perylene to 87% for the gas phase phenanthrene and particulate fluoranthene, respectively. Indeno[cd]pyrene plus benzo[ghi]perylene, known to be enhanced in gasoline-powered motor vehicle exhaust compared to diesel exhaust, had the lowest contribution of biomass combustion of the measured PAHs by 9%. The total organic carbon (TOC, defined as carbon remaining after removal of inorganic carbon) fbiomass was estimated to be 77%, which falls within the range for PAHs. This CSRA data of atmospheric PAHs demonstrate the non-uniformity of biomass combustion contribution to different PAHs even in a location with limited local emission sources and illustrates that regulatory efforts would not evenly reduce all PAHs.

  15. Source apportionment of organic aerosol across Houston, TX during DISCOVER-AQ

    NASA Astrophysics Data System (ADS)

    Yoon, S.; Clark, A. E.; Ortiz, S. M.; Usenko, S.; Sheesley, R. J.

    2015-12-01

    As part of the ground-based sampling efforts during DISCOVER-AQ's Houston month-long campaign in September 2013, atmospheric particulate matter (PM) samples were collected at four sites: Moody Tower (urban), Manvel Croix (southern suburb), Conroe (northern suburb), and La Porte (urban industrial). The Houston metropolitan area, especially the Houston Ship Channel, is a densely industrialized urban city with large concentrations of petroleum refining, petrochemical manufacturing, and heavy traffic during peak hours. Due to these and other emission sources, the area is heavily impacted by ambient PM. This study will be looking at fine PM (diameter less than 2.5µm, PM2.5) from all four sites. PM2.5fraction is relevant for understanding fate and transport of organic contaminants and is widely known to negatively impact human health. Chemical analysis including radiocarbon (14C) and organic tracer measurements (polycyclic aromatic hydrocarbons, alkanes, hopanes, steranes, and levoglucosan) were used for source apportionment. The 14C measurements constrained CMB results to estimate both primary and secondary contributions to total organic carbon (TOC). Results indicate that Moody Tower had consistent primary motor vehicle exhaust contribution (18-27%) and a fossil secondary organic aerosol (SOA) contribution from 5-33% depending on atmospheric conditions. Conroe had a lower contribution of motor vehicle exhaust (5-10%) and similarly variable fraction of fossil SOA (4-25%). Manvel Croix had an interim motor vehicle contribution (9-15%) with a variable fossil SOA (5-30%). For contemporary OC, there was minimal contribution of wood smoke during examined weeks (0-9%) but larger contributor of biogenic SOA ranging from 40-75% at Moody Tower, 56-81% at Manvel Croix and 60-79% at Conroe. Overall, the motor vehicle contribution was consistent at each site during the analysis week, biogenic SOA was consistently high, while fossil SOA showed the most variability.

  16. Successful application of lead isotopes in source apportionment, legal proceedings, remediation and monitoring.

    PubMed

    Gulson, Brian; Korsch, Michael; Winchester, Wayne; Devenish, Matthew; Hobbs, Thad; Main, Cleve; Smith, Gerard; Rosman, Kevin; Howearth, Lynette; Burn-Nunes, Laurie; Seow, Jimmy; Oxford, Cameron; Yun, Gracie; Gillam, Lindsay; Crisp, Michelle

    2012-01-01

    In late 2006, the seaside community in Esperance Western Australia was alerted to thousands of native bird species dying. The source of the lead (Pb) was determined by Pb isotopes to derive from the handling of Pb carbonate concentrate through the Port, which began in July 2005. Concern was expressed for the impact of this on the community. Our objectives were to employ Pb isotope ratios to evaluate the source of Pb in environmental samples for use in legal proceedings, and for use in remediation and monitoring. Isotope measurements were undertaken of bird livers, plants, drinking water, soil, harbour sediments, air, bulk ceiling dust, gutter sludge, surface swabs and blood. The unique lead isotopic signature of the contaminating Pb carbonate enabled diagnostic apportionment of lead in samples. Apart from some soil and water samples, the proportion of contaminating Pb was >95% in the environmental samples. Lead isotopes were critical in resolving legal proceedings, are being used in the remediation of premises, were used in monitoring of workers involved in the decontamination of the storage facility, and monitoring transport of the concentrate through another port facility. Air samples show the continued presence of contaminant Pb, more than one year after shipping of concentrate ceased, probably arising from dust resuspension. Brief details of the comprehensive testing and cleanup of the Esperance community are provided along with the role of the Community. Lead isotopic analyses can provide significant benefits to regulatory agencies, interested parties, and the community where the signature is able to be characterised with a high degree of certainty.

  17. Source apportionment of fine particulate matter in Phoenix, AZ, using positive matrix factorization

    SciTech Connect

    Steven G. Brown; Anna Frankel; Sean M. Raffuse; Paul T. Roberts; Hilary R. Hafner; Darcy J. Anderson

    2007-06-15

    Speciated particulate matter PM2.5 data collected as Part. of the Interagency Monitoring of Protected Visual Environments (IMPROVE) program in Phoenix, AZ, from April 2001 through October 2003 were analyzed using the multivariate receptor model, positive matrix factorization (PMF). Over 250 samples and 24 species were used, including the organic carbon and elemental carbon analytical temperature fractions from the thermal optical reflectance method. A two-step approach was used. First, the species excluding the carbon fractions were used, and initially eight factors were identified; non-soil potassium was calculated and included to better refine the burning factor. Next, the mass associated with the burning factor was removed, and the data set rerun with the carbon fractions. Results were very similar (i.e., within a few percent), but this step enabled a separation of the mobile factor into gasoline and diesel vehicle emissions. The identified factors were burning (on average 2% of the mass), secondary transport (7%), regional power generation (13%), dust (25%), nitrate (9%), industrial As/Pb/Se (2%), Cu/Ni/V (7%), diesel (9%), and general mobile (26%). Most of the long-range transport of emissions emanates from south of Phoenix in Southeastern Arizona, West Texas, and Mexico, which are significant source regions of SO{sub 2} emissions from coal- and oil-fired power plants. The overall contribution from mobile sources also increased, as some mass (OC and nitrate) from the nitrate and regional power generation factors were apportioned with the mobile factors. This approach allowed better apportionment of carbon as well as total mass. Additionally, the use of multiple supporting analyses, including air mass trajectories, activity trends, and emission inventory information, helped increase confidence in factor identification. 86 refs., 10 figs., 2 tabs.

  18. Metals and metalloids in atmospheric dust: Use of lead isotopic analysis for source apportionment

    NASA Astrophysics Data System (ADS)

    Felix Villar, Omar I.

    Mining activities generate aerosol in a wide range of sizes. Smelting activities produce mainly fine particles (<1 microm). On the other hand, milling, crushing and refining processes, as well tailings management, are significant sources of coarse particles (> 1 microm). The adverse effects of aerosols on human health depend mainly on two key characteristics: size and chemical composition. One of the main objectives of this research is to analyze the size distribution of contaminants in aerosol produced by mining operations. For this purpose, a Micro-Orifice Uniform Deposit Impactor (MOUDI) was utilized. Results from the MOUDI samples show higher concentrations of the toxic elements like lead and arsenic in the fine fraction (<1 microm). Fine particles are more likely to be deposited in the deeper zones of the respiratory system; therefore, they are more dangerous than coarse particles that can be filtered out in the upper respiratory system. Unfortunately, knowing the total concentration of contaminants does not give us enough information to identify the source of contamination. For this reason, lead isotopes have been introduced as fingerprints for source apportionment. Each source of lead has specific isotopic ratios; by knowing these ratios sources can be identified. During this research, lead isotopic ratios were analyzed at different sites and for different aerosol sizes. From these analyses it can be concluded that lead isotopes are a powerful tool to identify sources of lead. Mitigation strategies could be developed if the source of contamination is well defined. Environmental conditions as wind speed, wind direction, relative humidity and precipitation have an important role in the concentration of atmospheric dust. Dry environments with low relative humidity are ideal for the transport of aerosols. Results obtained from this research show the relationship between dust concentrations and meteorological parameters. Dust concentrations are highly correlated

  19. Advanced source apportionment of size-resolved trace elements at multiple sites in London during winter

    NASA Astrophysics Data System (ADS)

    Visser, S.; Slowik, J. G.; Furger, M.; Zotter, P.; Bukowiecki, N.; Canonaco, F.; Flechsig, U.; Appel, K.; Green, D. C.; Tremper, A. H.; Young, D. E.; Williams, P. I.; Allan, J. D.; Coe, H.; Williams, L. R.; Mohr, C.; Xu, L.; Ng, N. L.; Nemitz, E.; Barlow, J. F.; Halios, C. H.; Fleming, Z. L.; Baltensperger, U.; Prévôt, A. S. H.

    2015-10-01

    Trace element measurements in PM10-2.5, PM2.5-1.0 and PM1.0-0.3 aerosol were performed with 2 h time resolution at kerbside, urban background and rural sites during the ClearfLo winter 2012 campaign in London. The environment-dependent variability of emissions was characterized using the Multilinear Engine implementation of the positive matrix factorization model, conducted on data sets comprising all three sites but segregated by size. Combining the sites enabled separation of sources with high temporal covariance but significant spatial variability. Separation of sizes improved source resolution by preventing sources occurring in only a single size fraction from having too small a contribution for the model to resolve. Anchor profiles were retrieved internally by analysing data subsets, and these profiles were used in the analyses of the complete data sets of all sites for enhanced source apportionment. A total of nine different factors were resolved (notable elements in brackets): in PM10-2.5, brake wear (Cu, Zr, Sb, Ba), other traffic-related (Fe), resuspended dust (Si, Ca), sea/road salt (Cl), aged sea salt (Na, Mg) and industrial (Cr, Ni); in PM2.5-1.0, brake wear, other traffic-related, resuspended dust, sea/road salt, aged sea salt and S-rich (S); and in PM1.0-0.3, traffic-related (Fe, Cu, Zr, Sb, Ba), resuspended dust, sea/road salt, aged sea salt, reacted Cl (Cl), S-rich and solid fuel (K, Pb). Human activities enhance the kerb-to-rural concentration gradients of coarse aged sea salt, typically considered to have a natural source, by 1.7-2.2. These site-dependent concentration differences reflect the effect of local resuspension processes in London. The anthropogenically influenced factors traffic (brake wear and other traffic-related processes), dust and sea/road salt provide further kerb-to-rural concentration enhancements by direct source emissions by a factor of 3.5-12.7. The traffic and dust factors are mainly emitted in PM10-2.5 and show strong

  20. Chemical Characterization and Source Apportionment of Particulate Matter in Lahore, Pakistan

    NASA Astrophysics Data System (ADS)

    von Schneidemesser, Erika; Stone, Elizabeth; Quraishi, Tauseef; Schauer, James; Shafer, Martin; Mahmood, Abid

    2010-05-01

    Lahore, Pakistan is a rapidly growing megacity with a population approaching 10 million. A significant issue affecting many of the world's megacities is extremely high levels of air pollution associated with transportation, solid fuel combustion, and industrial sources. High ambient concentrations of particulate matter (PM), as well as high levels of toxic components of PM, have been linked to increased mortality and morbidity. Although much focus has been directed at particulate matter mass, in many developing and underdeveloped nations, the adverse health impacts of high levels of PM are further enhanced by the high concentrations of toxic components in PM. To address these issues is Lahore, a measurement campaign of fine (PM2.5) and coarse (PM10-2.5) particulate matter was conducted for the 2007 calendar year, which included measurements of particle mass, detailed chemical composition of PM and source apportionment calculations. Annual average PM2.5 and PM10 concentrations were measured to be 194 µg m-3 and 336 µg m-3, respectively, with daily 24-hour maximum concentrations of 410 µg m-3 and 650 µg m-3 for PM2.5 and PM10, respectively. PM2.5 and PM10 samples were analysed for organic and elemental carbon, organic species, ionic species, elemental composition, water soluble elements and biological activity using a macrophage ROS assay. The coarse mode was dominated by crustal dust components, while the fine fraction was dominated by carbonaceous aerosols. The PM10 elemental composition data, which included data for toxic metals, was processed using principle component analysis to determine likely source categories. Seven factors were identified explaining 91% of the variance of the measured components. The factors included a number of industrial sources, re-suspended soil, mobile sources, and regional secondary aerosol. Source contributions to the organic carbon (OC) component of the PM2.5 fraction were identified using organic tracer species and chemical

  1. Fine particulate matter in the tropical environment: monsoonal effects, source apportionment, and health risk assessment

    NASA Astrophysics Data System (ADS)

    Khan, M. F.; Latif, M. T.; Saw, W. H.; Amil, N.; Nadzir, M. S. M.; Sahani, M.; Tahir, N. M.; Chung, J. X.

    2016-01-01

    The health implications of PM2.5 in the tropical region of Southeast Asia (SEA) are significant as PM2.5 can pose serious health concerns. PM2.5 concentration and sources here are strongly influenced by changes in the monsoon regime from the south-west quadrant to the north-east quadrant in the region. In this work, PM2.5 samples were collected at a semi-urban area using a high-volume air sampler at different seasons on 24 h basis. Analysis of trace elements and water-soluble ions was performed using inductively coupled plasma mass spectroscopy (ICP-MS) and ion chromatography (IC), respectively. Apportionment analysis of PM2.5 was carried out using the United States Environmental Protection Agency (US EPA) positive matrix factorization (PMF) 5.0 and a mass closure model. We quantitatively characterized the health risks posed to human populations through the inhalation of selected heavy metals in PM2.5. 48 % of the samples collected exceeded the World Health Organization (WHO) 24 h PM2.5 guideline but only 19 % of the samples exceeded 24 h US EPA National Ambient Air Quality Standard (NAAQS). The PM2.5 concentration was slightly higher during the north-east monsoon compared to south-west monsoon. The main trace metals identified were As, Pb, Cd, Ni, Mn, V, and Cr while the main ions were SO42-, NO3-, NH4+, and Na. The mass closure model identified four major sources of PM2.5 that account for 55 % of total mass balance. The four sources are mineral matter (MIN) (35 %), secondary inorganic aerosol (SIA) (11 %), sea salt (SS) (7 %), and trace elements (TE) (2 %). PMF 5.0 elucidated five potential sources: motor vehicle emissions coupled with biomass burning (31 %) were the most dominant, followed by marine/sulfate aerosol (20 %), coal burning (19 %), nitrate aerosol (17 %), and mineral/road dust (13 %). The hazard quotient (HQ) for four selected metals (Pb, As, Cd, and Ni) in PM2.5 mass was highest in PM2.5 mass from the coal burning source and least in PM2.5 mass

  2. Atmospheric aerosol compositions over the South China Sea: temporal variability and source apportionment

    NASA Astrophysics Data System (ADS)

    Xiao, Hong-Wei; Xiao, Hua-Yun; Luo, Li; Shen, Chun-Yan; Long, Ai-Min; Chen, Lin; Long, Zhen-Hua; Li, Da-Ning

    2017-03-01

    In order to evaluate impacts of different source emission on marine atmospheric particles over the South China Sea (SCS), major inorganic ionic concentrations (Na+, Cl-, SO42-, Ca2+, Mg2+, K+, NH4+ and NO3-) were determined in total suspended particulates (TSPs) at Yongxing Island, from March 2014 to February 2015. The annual average concentration of TSPs was 89.6 ± 68.0 µg m-3, with 114.7 ± 82.1, 60.4 ± 27.0 and 59.5 ± 25.6 µg m-3 in cool, warm and transition seasons, respectively. Cl- had the highest concentration, with an annual average of 7.73 ± 5.99 µg m-3, followed by SO42- (5.54 ± 3.65 µg m-3), Na+ (4.00 ± 1.88 µg m-3), Ca2+ (2.15 ± 1.54 µg m-3), NO3- (1.95 ± 1.34 µg m-3), Mg2+ (0.44 ± 0.33 µg m-3), K+ (0.33 ± 0.22 µg m-3) and NH4+ (0.07 ± 0.07 µg m-3). Concentrations of TSPs and the major ions showed seasonal variations, which were higher in the cool season and lower in the warm and transition seasons. Factors of influence were wind speed, temperature, relatively humidity, rain and air mass source region. Back trajectories, concentration-weighted trajectories (CWTs), and positive matrix factorization (PMF) of chemical compositions were analyzed for source apportionment, source contribution and spatiotemporal variation of major ions. Back trajectories and CWTs showed that air masses at Yongxing Island were mainly from the northeast, southwest and southeast in the cool, warm and transition seasons, respectively. The PMF results showed that 77.4 % of Na+ and 99.3 % of Cl- were from sea salt; 60.5 % of NH4+ was from oceanic emission. Anthropogenic sources were very important for atmospheric aerosols over the island. Secondary inorganic aerosol of SO2 and NOx from fossil fuel combustion (especially coal in Chinese coastal regions) was the dominant source of NO3- (69.5 %) and SO42- (57.5 %).

  3. Winter-time size distribution and source apportionment of total suspended particulate matter and associated metals in Delhi

    NASA Astrophysics Data System (ADS)

    Srivastava, Arun; Gupta, Sandeep; Jain, V. K.

    2009-03-01

    A study of the winter time size distribution and source apportionment of total suspended particulate matter (TSPM) and associated heavy metal concentrations have been carried out for the city of Delhi. This study is important from the point of view of implementation of compressed natural gas (CNG) as alternate of diesel fuel in the public transport system in 2001 to reduce the pollution level. TSPM were collected using a five-stage cascade impactor at six sites in the winters of 2005-06. The results of size distribution indicate that a major portion (~ 40%) of TSPM concentration is in the form of PM0.7 (< 0.7 μm). Similar trends were observed with most of the heavy metals associated with various size fractions of TSPM. A very good correlation between coarse and fine size fraction of TSPM was observed. It was also observed that the metals associated with coarse particles have more chances of correlation with other metals; rather they are associated with fine particles. Source apportionment was carried out separately in coarse and fine size modes of TSPM by Chemical Mass Balance Receptor Model (CMB8) as well as by Principle Component Analysis (PCA) of SPSS. Source apportionment by PCA reveals that there are two major sources (possibly vehicular and crustal re-suspension) in both coarse and fine size fractions. Results obtained by CMB8 show the dominance of vehicular pollutants and crustal dust in fine and coarse size mode respectively. Noticeably the dominance of vehicular pollutants are now confined to fine size only whilst during pre CNG era it dominated both coarse and fine size mode. An increase of 42.5, 44.4, 48.2, 38.6 and 38.9% in the concentrations of TSPM, PM10.9, coarse particles, fine particles and lead respectively was observed during pre (2001) to post CNG (2005-06) period.

  4. Spatial distribution, potential risk assessment, and source apportionment of polycyclic aromatic hydrocarbons (PAHs) in sediments of Lake Chaohu, China.

    PubMed

    Li, Chaocan; Huo, Shouliang; Yu, Zhiqiang; Xi, Beidou; Zeng, Xiangying; Wu, Fengchang

    2014-10-01

    Twenty-nine sediment samples were collected from Lake Chaohu, a shallow eutrophic lake in Eastern China, and were analyzed for 15 priority polycyclic aromatic hydrocarbons (PAHs) to determine the spatial distribution and exposure risks of PAHs. Three receptor models, the principal component analysis-multiple linear regression (PCA-MLR) model, the positive matrix factorization (PMF) model, and the Unmix model, were used in combination with the PAHs diagnostic ratios to investigate the potential source apportionment of PAHs. A clear gradient in the spatial distribution and the potential toxicity of PAHs was observed from west to east in the sediments of Lake Chaohu. ∑15PAH concentrations and the TEQ were in the range of 80.82-30 365.01 ng g(-1) d.w. and 40.77-614.03, respectively. The highest values of the aforementioned variables were attributed to urban-industrial pollution sources in the west lake region, and the levels decreased away from the river inlets. The three different models yielded excellent correlation coefficients between the predicted and measured levels of the 15 PAH compounds. Similarly, source apportionment results were derived from the three receptor models and the PAH diagnostic ratios, suggesting that the highest contribution to the PAHs was from coal combustion and wood combustion, followed by vehicular emissions. The PMF model yielded the following contributions to the PAHs from gasoline combustion, diesel combustion, unburned petroleum emissions, and wood combustion: 34.49, 24.61, 16.11, 13.01, and 11.78 %, respectively. The PMF model produced more detailed source apportionment results for the PAHs than the PCA-MLR and Unmix models.

  5. On the autarchic use of solely PIXE data in particulate matter source apportionment studies by receptor modeling

    NASA Astrophysics Data System (ADS)

    Lucarelli, F.; Nava, S.; Calzolai, G.; Chiari, M.; Giannoni, M.; Traversi, R.; Udisti, R.

    2015-11-01

    Particle Induced X-ray Emission (PIXE) analysis of aerosol samples allows simultaneous detection of several elements, including important tracers of many particulate matter sources. This capability, together with the possibility of analyzing a high number of samples in very short times, makes PIXE a very effective tool for source apportionment studies by receptor modeling. However, important aerosol components, like nitrates, OC and EC, cannot be assessed by PIXE: this limitation may strongly compromise the results of a source apportionment study if based on PIXE data alone. In this work, an experimental dataset characterised by an extended chemical speciation (elements, EC-OC, ions) is used to test the effect of reducing input species in the application of one of the most widely used receptor model, namely Positive Matrix Factorization (PMF). The main effect of using only PIXE data is that the secondary nitrate source is not identified and the contribution of biomass burning is overestimated, probably due to the similar seasonal pattern of these two sources.

  6. Background concentrations and source apportionment of polycyclic aromatic hydrocarbons in south-eastern Finland

    NASA Astrophysics Data System (ADS)

    Vestenius, Mika; Leppänen, Sirkka; Anttila, Pia; Kyllönen, Katriina; Hatakka, Juha; Hellén, Heidi; Hyvärinen, Antti-Pekka; Hakola, Hannele

    2011-07-01

    Polycyclic aromatic hydrocarbons (PAH compounds) were measured in the PM 10 fraction [from ambient air] at Virolahti, Finland. The sampling site is located in a rural area in the south-eastern corner of Finland, near the Russian border. Altogether, 51 daily and 85 weekly filter samples were collected in 2007-2008. The yearly average concentration of benzo(a)pyrene at Virolahti in 2007 was 0.21 ng m -3, which is well below the annual target value of 1 ng m -3 set by the European Union. The positive matrix factorization (PMF) method was applied in source apportionment for daily PAH data combined with other pollutant data. A three-factor solution of the PMF analysis with 28 components was chosen. These three factors were identified as long-range transported secondary particles (F1), combustion (F2) and a sea-salt factor (F3). The conditional probability function (CPF) was used to combine wind direction sectors with the PMF factors. In cases F1 and F2, pollutants mainly originated from the south-east, whereas pollutants in F3 came from the south-western sector. PAHs entered into the combustion factor 2 together with SO 2, NO x, black carbon and potassium. This suggests that the PAHs at Virolahti originated from traffic and industrial pollution, as well as biomass burning. Elevated concentrations occurred throughout the winter period and most frequently originated from the south-eastern sector between 90°-135°. This sector includes, among other transboundary areas, the metropolis of St. Petersburg at a distance of 160 km.

  7. Seasonal effect and source apportionment of polycyclic aromatic hydrocarbons in PM2.5

    NASA Astrophysics Data System (ADS)

    Khan, Md Firoz; Latif, Mohd Talib; Lim, Chee Hou; Amil, Norhaniza; Jaafar, Shoffian Amin; Dominick, Doreena; Mohd Nadzir, Mohd Shahrul; Sahani, Mazrura; Tahir, Norhayati Mohd

    2015-04-01

    This study aims to investigate distribution and sources of 16 polycyclic aromatic hydrocarbons (PAHs) bound to fine particulate matter (PM2.5) captured in a semi-urban area in Malaysia during different seasons, and to assess their health risks. PM2.5 samples were collected using a high volume air sampler on quartz filter paper at a flow rate of 1 m3 min-1 for 24 h. PAHs on the filter paper were extracted with dichloromethane (DCM) using an ultrasonic centrifuge solid-phase extraction method and measured by gas chromatography-mass spectroscopy. The results showed that the range of PAHs concentrations in the study period was between 0.21 and 12.08 ng m-3. The concentrations of PAHs were higher during the south-west monsoon (0.21-12.08 ng m-3) compared to the north-east monsoon (0.68-3.80 ng m-3). The high molecular weight (HMW) PAHs (≥5 ring) are significantly prominent (>70%) compared to the low molecular weight (LMW) PAHs (≤4 ring) in PM2.5. The Spearman correlation indicates that the LMW and HMW PAHs correlate strongly among themselves. The diagnostic ratios (DRs) of I[c]P/I[c]P + BgP and B[a]P/B[g]P suggest that the HMW PAHs originated from fuel combustion sources. The source apportionment analysis of PAHs was resolved using DRs-positive matrix factorization (PMF)-multiple linear regression (MLR). The main sources identified were (a) gasoline combustion (65%), (b) diesel and heavy oil combustion (19%) and (c) natural gas and coal burning (15%). The health risk evaluation, by means of the lifetime lung cancer risk (LLCR), showed no potential carcinogenic risk from the airborne BaPeq (which represents total PAHs at the present study area in Malaysia). The seasonal LLCR showed that the carcinogenic risk of total PAHs were two fold higher during south-westerly monsoon compared to north-easterly monsoon.

  8. Pollution characteristics, source apportionment, and health risk of heavy metals in street dust of Suzhou, China.

    PubMed

    Lin, Manli; Gui, Herong; Wang, Yao; Peng, Weihua

    2017-01-01

    To analyze the pollution characteristics, source apportionment, and health risk of heavy metals (HMs) in street dust of Suzhou, China, 23 sampling sites were selected and periodically sampled for 12 months. A total of 276 samples were collected, and the concentrations of selected HMs (e.g., Cr, Cu, Fe, Mn, Pb, V, and Zn) were examined with an X-ray fluorescence spectrum analyzer. Results showed that the mean concentrations of Cr, Cu, Fe, Mn, Pb, V, and Zn in the street dust of Suzhou were 112.9, 27.5, 19941.3, 410.3, 45.2, 75.6, and 225.3 mg kg(-1), respectively. Cr, Cu, Pb, and Zn exceeded their background values in local natural soils by 1.3-3.6-fold, whereas Fe, Mn, and V were all within their background values. However, enrichment factor analysis revealed that Cr, Cu, Mn, Pb, V, and Zn, especially Cr, Cu, Pb, and Zn, were enriched in Suzhou street dust. The HMs showed no significant seasonal changes overall, but spatial distribution analysis implied that the high values of Cr, Cu, Mn, Pb, V, and Zn were mainly distributed in areas with frequent human activities. Results of multivariate techniques (e.g., Pearson correlation, hierarchical cluster, and principal components analyses) suggested that Pb and Zn had complicated sources; Cu and V mainly originated from traffic sources; Fe and Mn mainly came from natural sources; and Cr was dominantly related to industrial district. Health risk assessment revealed that a single heavy metal might not cause both non-cancer and carcinogenic risks to local residents. Nevertheless, the sum of the hazard index of all selected HMs for children slightly exceeded the safety value, thereby implying that the HMs from Suzhou street dust can possibly produce significant risk to children. Cr was the priority pollutant in the study area because of its high concentration, high enrichment, and high contribution to non-cancer risk values.

  9. Triple-Isotope-Based Source Apportionment of Methane in Waters of the Outer Laptev Sea

    NASA Astrophysics Data System (ADS)

    Steinbach, J.; Holmstrand, H.; Shcherbakova, K.; Kosmach, D.; Sapart, C. J.; Panova, E.; Bruchert, V.; Semiletov, I. P.; Shakhova, N. E.; Gustafsson, O.

    2015-12-01

    The East Siberian Arctic Shelf (ESAS) hosts large methane (CH4) deposits in the form of gas hydrates, gas pockets within subsea permafrost and in deeper reservoirs. For over a decade, annual expeditions have documented methane releases into the water column in large parts of this region. However, there is still insufficient knowledge of which pools are releasing the methane - one important piece of information required for a deeper understanding of the system and towards predicting future releases. A powerful tool for quantifying the relative contribution of releases from different sources is multi-dimensional isotope analysis of CH4 in the water column. Using the full triple isotope characterization (δ13C-CH4, δD-CH4, Δ14C-CH4) allows deconvolution of CH4 sources between thermogenic and biogenic origins and of different reservoir ages.During the SWERUS-C3 expedition in summer 2014 we investigated the distribution of dissolved methane and its isotope signatures in the water column along the outer ESAS and its adjacent slope and ridges. Over 1500 samples for CH4 concentration from high-resolution vertical profiles (up to 12 depths) were analyzed onboard; 900 samples were taken for stable isotopes analysis; and a total of 80 larger water samples were taken at selected locations for Δ14C-CH4 analysis. CH4 was extracted from these samples onboard using custom-built CH4-stripping systems and stored in absorbent traps for further processing and radiocarbon analysis onshore. One focus was to probe CH4 sources in seep areas, identified by a combination of geophysical features in the sediment, observation of bubbles in the water column and measured CH4 profiles. Here we present triple isotope data from inside and outside seep areas of the outer Laptev Sea and source-apportionment for this region. Dissolved methane concentration there reached up to 1400nM. Stable isotopes results in near bottom waters are rather enriched: Initial results show -142 to -133‰ vs SMOW for

  10. Source apportionment of PM10, organic carbon and elemental carbon at Swiss sites: an intercomparison of different approaches.

    PubMed

    Gianini, M F D; Piot, C; Herich, H; Besombes, J-L; Jaffrezo, J-L; Hueglin, C

    2013-06-01

    In this study, the results of source apportionment of particulate matter (PM10), organic carbon (OC), and elemental carbon (EC) - as obtained through different approaches at different types of sites (urban background, urban roadside, and two rural sites in Switzerland) - are compared. The methods included in this intercomparison are positive matrix factorisation modelling (PMF, applied to chemical composition data including trace elements, inorganic ions, OC, and EC), molecular marker chemical mass balance modelling (MM-CMB), and the aethalometer model (AeM). At all sites, the agreement of the obtained source contributions was reasonable for OC, EC, and PM10. Based on an annual average, and at most of the considered sites, secondary organic carbon (SOC) is the component with the largest contribution to total OC; the most important primary source of OC is wood combustion, followed by road traffic. Secondary aerosols predominate in PM10. All considered techniques identified road traffic as the dominant source of EC, while wood combustion emissions are of minor importance for this constituent. The intercomparison of different source apportionment approaches is helpful to identify the strengths and the weaknesses of the different methods. Application of PMF has limitations when source emissions have a strong temporal correlation, or when meteorology has a strong impact on PM variability. In these cases, the use of PMF can result in mixed source profiles and consequently in the under- or overestimation of the real-world sources. The application of CMB models can be hampered by the unavailability of source profiles and the non-representativeness of the available profiles for local source emissions. This study also underlines that chemical transformations of molecular markers in the atmosphere can lead to the underestimation of contributions from primary sources, in particular during the summer period or when emission sources are far away from the receptor sites.

  11. Source apportionment of particulate matter in a South Asian Mega City: A case study of Karachi

    NASA Astrophysics Data System (ADS)

    Shahid, imran

    2016-04-01

    PM2.5 and PM10-2.5. In order to make air quality better and risk free in South Asian cities a comprehensive and integrated regional effort is required that include continuous air quality monitoring, source apportionment and implementation of regional air quality policies.

  12. Characterization and source apportionment of polycyclic aromatic hydrocarbons (PAHs) in Sediments from the Bohai Sea, China

    NASA Astrophysics Data System (ADS)

    Liu, Jihua; Hu, Ningjing; Shi, Xuefa

    2015-04-01

    Characterization and source apportionment of polycyclic aromatic hydrocarbons (PAHs) in Sediments from the Bohai Sea, China Liu Jihua, Hu Ningjing, Shi Xuefa First Institute of Oceanography, State Oceanic Administration, Qingdao 266061, China Polycyclic aromatic hydrocarbons (PAHs) are a class of ubiquitous organic contaminants in the environment. Indeed, 16 PAH compounds have been listed as priority pollutants by the United States Environmental Protection Agency and the European Union because of their potential toxicity to humans and ecosystems. As POPs are released or escape into the environment, their global accumulation in marine sediments generates a complex balance between inputs and outputs. Furthermore, PAHs in coastal sediments can serve as effective tracers of materials transport from land-to-sea (Fang et al., 2009). Hence, investigations of PAHs in sediments can provide useful information for further understanding of environmental processes and material transport. In this study, sixteen polycyclic aromatic hydrocarbons (PAHs) were extracted from a total of 112 surface sediment samples collected across the entire territory of the Bohai Sea. The detectable concentrations of PAHs ranged from 97.2 to 300.7 ng/g across all samples, indicating low contamination levels of PAHs compared with reported values for other coastal sediments in China and developed countries. The highest concentrations were found within three belts in the vicinity of Luan River Estuary-Qinhuangdao Harbor, the Cao River Estuary-Bohai Sea Center, and north of the Yellow River Estuary. The distribution patterns of PAHs and source identification implied that PAH contamination in the Bohai Sea mainly originates from offshore oil exploration, sewage discharge from rivers and shipping activities. Further Principal components analysis (PCA)/multivariate linear regression (MLR) analysis suggested that the contributions of spilled oil products (petrogenic), coal combustion and traffic

  13. Characterization of emissions from South Asian biofuels and application to source apportionment of carbonaceous aerosol in the Himalayas

    NASA Astrophysics Data System (ADS)

    Stone, Elizabeth A.; Schauer, James J.; Pradhan, Bidya Banmali; Dangol, Pradeep Man; Habib, Gazala; Venkataraman, Chandra; Ramanathan, V.

    2010-03-01

    This study focuses on improving source apportionment of carbonaceous aerosol in South Asia and consists of three parts: (1) development of novel molecular marker-based profiles for real-world biofuel combustion, (2) application of these profiles to a year-long data set, and (3) evaluation of profiles by an in-depth sensitivity analysis. Emissions profiles for biomass fuels were developed through source testing of a residential stove commonly used in South Asia. Wood fuels were combusted at high and low rates, which corresponded to source profiles high in organic carbon (OC) or high in elemental carbon (EC), respectively. Crop wastes common to the region, including rice straw, mustard stalk, jute stalk, soybean stalk, and animal residue burnings, were also characterized. Biofuel profiles were used in a source apportionment study of OC and EC in Godavari, Nepal. This site is located in the foothills of the Himalayas and was selected for its well-mixed and regionally impacted air masses. At Godavari, daily samples of fine particulate matter (PM2.5) were collected throughout the year of 2006, and the annual trends in particulate mass, OC, and EC followed the occurrence of a regional haze in South Asia. Maximum concentrations occurred during the dry winter season and minimum concentrations occurred during the summer monsoon season. Specific organic compounds unique to aerosol sources, molecular markers, were measured in monthly composite samples. These markers implicated motor vehicles, coal combustion, biomass burning, cow dung burning, vegetative detritus, and secondary organic aerosol as sources of carbonaceous aerosol. A molecular marker-based chemical mass balance (CMB) model provided a quantitative assessment of primary source contributions to carbonaceous aerosol. The new profiles were compared to widely used biomass burning profiles from the literature in a sensitivity analysis. This analysis indicated a high degree of stability in estimates of source

  14. Measurement of Organic and Inorganic Chemical Tracers for Source Apportionment of Tropospheric Aerosols Collected During the ACE-Asia Experiment

    NASA Astrophysics Data System (ADS)

    Schauer, J. J.; Park, J.; Duvall, R.; Bae, M.; Shafer, M. M.; Chuang, P.; Chuang, P.; Kim, Y. J.

    2001-12-01

    Naturally occurring dust and anthropogenic air pollutants are important contributors to tropospheric aerosols and impact air quality and the radiative balance of the Earth's atmosphere. In order to better understand the relationship between the origin, chemical composition and ultimate impact of Asian aerosols on climate forcing, aerosol samples were collected as part of the ACE-Asia experiment for detailed chemical analysis. Atmospheric particulate matter samples were collected from March 27, 2001 through May 6, 2001 at the ACE-Asia ground station located on Cheju Island, Korea. During this period, this region is impacted by anthropogenic air pollution emissions from highly urbanized region of Asia and by desert dust originating from northeastern Asia. As part of the experiment, atmospheric particulate matter samplers were also collected in urban and desert locations in Asia that represent regional sources of particulate matter in Asia. Size resolved aerosol samples were analyzed for trace metals by using microwave assisted-acid digestion and ICP-MS analysis, speciated organic compounds using solvent extraction and GC-MS analysis, as well as soluble ions and elemental and organic carbon (ECOC). These measurements provide fingerprints for source apportionment of the atmospheric particulate matter samples collected at the Cheju Island sampling site. The use of these chemical tracers for apportionment of wind-driven long range transported desert dust, local crustal derived dust, biogenically and anthropogenically derived sulfate, specific urban combustion source, and fossil fuel combustion will be presented.

  15. Concentration levels and source apportionment of ultrafine particles in road microenvironments

    NASA Astrophysics Data System (ADS)

    Argyropoulos, G.; Samara, C.; Voutsa, D.; Kouras, A.; Manoli, E.; Voliotis, A.; Tsakis, A.; Chasapidis, L.; Konstandopoulos, A.; Eleftheriadis, K.

    2016-03-01

    A mobile laboratory unit (MOBILAB) with on-board instrumentation (Scanning Mobility Particle Sizer, SMPS; Ambient NOx analyzer) was used to measure size-resolved particle number concentrations (PNCs) of quasi-ultrafine particles (UFPs, 9-372 nm), along with NOx, in road microenvironments. On-road measurements were carried out in and around a large Greek urban agglomeration, the Thessaloniki Metropolitan Area (TMA). Two 2-week measurement campaigns were conducted during the warm period of 2011 and the cold period of 2012. During each sampling campaign, MOBILAB was driven through a 5-day inner-city route and a second 5-day external route covering in total a wide range of districts (urban, urban background, industrial and residential), and road types (major and minor urban roads, freeways, arterial and interurban roads). All routes were conducted during working days, in morning and in afternoon hours under real-world traffic conditions. Spatial classification of MOBILAB measurements involved the assignment of measurement points to location bins defined by the aspect ratio of adjacent urban street canyons (USCs). Source apportionment was further carried out, by applying Positive Matrix Factorization (PMF) to particle size distribution data. Apportioned PMF factors were interpreted, by employing a two-step methodology, which involved (a) statistical association of PMF factor contributions with 12 h air-mass back-trajectories ending at the TMA during MOBILAB measurements, and (b) Multiple Linear Regression (MLR) using PMF factor contributions as the dependent variables, while relative humidity, solar radiation flux, and vehicle speed were used as the independent variables. The applied data analysis showed that low-speed cruise and high-load engine operation modes are the two dominant sources of UFPs in most of the road microenvironments in the TMA, with significant contributions from background photochemical processes during the warm period, explaining the reversed

  16. AIRUSE-LIFE+: a harmonized PM speciation and source apportionment in 5 Southern European cities

    NASA Astrophysics Data System (ADS)

    Amato, F.; Alastuey, A.; Karanasiou, A.; Lucarelli, F.; Nava, S.; Calzolai, G.; Severi, M.; Becagli, S.; Gianelle, V. L.; Colombi, C.; Alves, C.; Custódio, D.; Nunes, T.; Cerqueira, M.; Pio, C.; Eleftheriadis, K.; Diapouli, E.; Reche, C.; Minguillón, M. C.; Manousakas, M.; Maggos, T.; Vratolis, S.; Harrison, R. M.; Querol, X.

    2015-09-01

    The AIRUSE-LIFE+ project aims at characterising similarities and heterogeneities in PM sources and contributions in urban areas from the Southern Europe. Once the main PMx sources are identified, AIRUSE aims at developing and testing the efficiency of specific and non-specific measures to improve urban air quality. This article reports the results of the source apportionment of PM10 and PM2.5 conducted at three urban background sites (Barcelona, Florence and Milan, BCN-UB, FI-UB, MLN-UB) one sub-urban background site (Athens, ATH-SUB) and one traffic site (Porto, POR-TR). After collecting 1047 PM10 and 1116 PM2.5 24 h samples from January 2013 to February 2014 simultaneously at the 5 cities, these were analysed for the contents of OC, EC, anions, cations, major and trace elements and levoglucosan. The USEPA PMF5 receptor model was applied to these datasets in a harmonised way for each city. The sum of vehicle exhaust and non-exhaust contributes within 3.9-10.8 μg m-3 (16-32 %) to PM10 and 2.3-9.4 μg m-3 (15-36 %) to PM2.5, although a fraction of secondary nitrate is also traffic-related but could not be estimated. Important contributions arise from secondary particles (nitrate, sulphate and organics) in PM2.5 (37-82 %) but also in PM10 (40-71 %) mostly at background sites, revealing the importance of abating gaseous precursors in designing air quality plans. Biomass burning (BB) contributions vary widely, from 14-24 % of PM10 in POR-TR, MLN-UB and FI-UB, 7 % in ATH-SUB to < 2 % in BCN-UB. In PM2.5, BB is the second most important source in MLN-UB (21 %) and in POR-TR (18 %), the third one in FI-UB (21 %) and ATH-SUB (11 %), but again negligible (< 2 %) in BCN-UB. This large variability among cities is mostly due to the degree of penetration of biomass for residential heating. In Barcelona natural gas is very well supplied across the city and used as fuel in 96 % of homes, while, in other cities, PM levels increase on an annual basis by 1-9 μg m-3 due to this

  17. AIRUSE-LIFE+: a harmonized PM speciation and source apportionment in five southern European cities

    NASA Astrophysics Data System (ADS)

    Amato, Fulvio; Alastuey, Andrés; Karanasiou, Angeliki; Lucarelli, Franco; Nava, Silvia; Calzolai, Giulia; Severi, Mirko; Becagli, Silvia; Gianelle, Vorne L.; Colombi, Cristina; Alves, Celia; Custódio, Danilo; Nunes, Teresa; Cerqueira, Mario; Pio, Casimiro; Eleftheriadis, Konstantinos; Diapouli, Evangelia; Reche, Cristina; Cruz Minguillón, María; Manousakas, Manousos-Ioannis; Maggos, Thomas; Vratolis, Stergios; Harrison, Roy M.; Querol, Xavier

    2016-03-01

    The AIRUSE-LIFE+ project aims at characterizing similarities and heterogeneities in particulate matter (PM) sources and contributions in urban areas from southern Europe. Once the main PMx sources are identified, AIRUSE aims at developing and testing the efficiency of specific and non-specific measures to improve urban air quality. This article reports the results of the source apportionment of PM10 and PM2.5 conducted at three urban background sites (Barcelona, Florence and Milan, BCN-UB, FI-UB and MLN-UB), one suburban background site (Athens, ATH-SUB) and one traffic site (Porto, POR-TR). After collecting 1047 PM10 and 1116 PM2.5 24 h samples during 12 months (from January 2013 on) simultaneously at the five cities, these were analysed for the contents of OC, EC, anions, cations, major and trace elements and levoglucosan. The USEPA PMF5 receptor model was applied to these data sets in a harmonized way for each city. The sum of vehicle exhaust (VEX) and non-exhaust (NEX) contributes between 3.9 and 10.8 µg m-3 (16-32 %) to PM10 and 2.3 and 9.4 µg m-3 (15-36 %) to PM2.5, although a fraction of secondary nitrate is also traffic-related but could not be estimated. Important contributions arise from secondary particles (nitrate, sulfate and organics) in PM2.5 (37-82 %) but also in PM10 (40-71 %), mostly at background sites, revealing the importance of abating gaseous precursors in designing air quality plans. Biomass burning (BB) contributions vary widely, from 14-24 % of PM10 in POR-TR, MLN-UB and FI-UB, 7 % in ATH-SUB, to < 2 % in BCN-UB. In PM2.5, BB is the second most important source in MLN-UB (21 %) and in POR-TR (18 %), the third one in FI-UB (21 %) and ATH-SUB (11 %), but is again negligible (< 2 %) in BCN-UB. This large variability among cities is mostly due to the degree of penetration of biomass for residential heating. In Barcelona natural gas is very well supplied across the city and is used as fuel in 96 % of homes, while in other cities, PM levels

  18. The source apportionment of polycyclic aromatic hydrocarbons (PAHs) in the topsoil in Xiaodian sewage irrigation area, North of China.

    PubMed

    Li, Jia-Le; Wang, Yan-Xin; Zhang, Cai-Xiang; Dong, Yi-Hui; Du, Bin; Liao, Xiao-Ping

    2014-12-01

    31 topsoil samples were collected by grid method in Xiaodian sewage irrigation area, Taiyuan City, North of China. The concentrations of 16 kinds of polycyclic aromatic hydrocarbons (PAHs) were determined by gas chromatograph coupled with mass spectrum. Generally speaking, the distribution order of PAHs in the area is: those with five and six rings > those with four rings > those with two and three rings. Source apportionment shows a significant zonation of the source of PAHs: the civil coal pollution occurred in the north part, the local and far factory pollution happened in the middle area and the mixed pollution sources from coal and wood combustion, automotive emission, presented in the south area. The distribution of PAHs has a definite relationship with the sewage water flow and soil adsorption. The related coefficient between PAHs and physicochemical property showed there was a negative correlation between pH, silt, clay and PAHs while there was a positive correlation between total organic carbon, sand and PAHs.

  19. Source apportionment and the role of meteorological conditions in the assessment of air pollution exposure due to urban emissions

    NASA Astrophysics Data System (ADS)

    Schäfer, K.; Elsasser, M.; Arteaga-Salas, J. M.; Gu, J.; Pitz, M.; Schnelle-Kreis, J.; Cyrys, J.; Emeis, S.; Prevot, A. S. H.; Zimmermann, R.

    2014-01-01

    As particulate matter (PM) impacts human health, knowledge about its composition, exposure and source apportionment is required. A study of the urban atmosphere in the case of Augsburg, Germany, during winter (31 January-12 March 2010) is thus presented here. Investigations were performed on the basis of aerosol mass spectrometry and further air pollutants and meteorological measurements, including mixing layer height. Organic matter was separated by source apportionment of PM1 with positive matrix factorization (PMF) in three factors: OOA - oxygenated organic aerosol (secondary organic factor), HOA - hydrocarbon-like organic aerosol (traffic factor or primary organic factor) and WCOA - wood combustion organic aerosol (wood combustion factor), which extend the information from black carbon (BC) measurements. PMF was also applied to the particle size distribution (PSD) data of PM2.5 to determine different source profiles and we assigned them to the particle sources: nucleation aerosol, fresh traffic aerosol, aged traffic aerosol, stationary combustion aerosol and secondary aerosol. Ten different temporal phases were identified on the basis of weather characteristics and aerosol composition and used for correlations of all air pollutants and meteorological parameters. While source apportionment from both organic PM composition and PSD agree and show that the main emission sources of PM exposure are road traffic as well as stationary and wood combustion, secondary aerosol factor concentrations are very often the highest ones. The hierarchical clustering analysis with the Ward method of cross-correlations of each air pollutant and PM component and of the correlations of each pollutant with all meteorological parameters provided two clusters: "secondary pollutants of PM1 and fine particles" and "primary pollutants (including CO and benzene) and accumulation mode particles". The dominant meteorological influences on pollutant concentrations are wind speed and mixing

  20. Concentrations and source apportionment of PM10 and associated major and trace elements in the Rhodes Island, Greece.

    PubMed

    Argyropoulos, Georgios; Manoli, Evangelia; Kouras, Athanasios; Samara, Constantini

    2012-08-15

    Ambient concentrations of PM(10) and associated major and trace elements were measured over the cold and the warm season of 2007 at two sites located in the Rhodes Island (Greece), in Eastern Mediterranean, aimed at source apportionment by Chemical Mass Balance (CMB) receptor modeling. Source chemical profiles, necessary in CMB modeling, were obtained for a variety of emission sources that could possibly affect the study area, including sea spray, geological material, soot emissions from the nearby oil-fuelled thermal power plant, and other anthropogenic activities, such as vehicular traffic, residential oil combustion, wood burning, and uncontrolled open-air burning of agricultural biomass and municipal waste. Source apportionment of PM(10) and elemental components was carried out by employing an advanced CMB version, the Robotic Chemical Mass Balance model (RCMB). Vehicular emissions were found to be major PM(10) contributor accounting, on average, for 36.8% and 31.7% during the cold period, and for 40.9% and 39.2% in the warm period at the two sites, respectively. The second largest source of ambient PM(10), with minor seasonal variation, was secondary sulfates (mainly ammonium and calcium sulfates), with total average contribution around 16.5% and 18% at the two sites. Soil dust was also a remarkable source contributing around 22% in the warm period, whereas only around 10% in the cold season. Soot emitted from the thermal power plant was found to be negligible contributor to ambient PM(10) (<1%), however it appeared to appreciably contribute to the ambient V and Ni (11.3% and 5.1%, respectively) at one of the sites during the warm period, when electricity production is intensified. Trajectory analysis did not indicate any transport of Sahara dust; on the contrary, long range transport of soil dust from arid continental regions of Minor Asia and of biomass burning aerosol from the countries surrounding the Black Sea was considered possible.

  1. Studying organic aerosols during bonfire night in Manchester: ME-2 source apportionment

    NASA Astrophysics Data System (ADS)

    Reyes Villegas, Ernesto; Allan, James

    2016-04-01

    conditions: 5°C in 2014; 12°C in 2013. For NH4NO3, a range of 1.5-2.9 for the ratio of concentrations NO+/NO+2 (m/z ratio of 30:46) has previously been reported (Fry et al. 2009) while the ratio for organic nitrate is much higher, with values of 10-15 (Hao et al. 2014). In this study, a ratio of 9.5 was observed on bonfire night and a ratio of 3.5 was observed during episodes without bonfire/fireworks emissions. This study shows OA source apportionment on bonfire night where significant SFOA emissions are present, suggesting that high concentrations are not only attributed to bonfires/fireworks emissions but also to meteorological conditions. Organic nitrate was identified during bonfire night suggesting a nighttime chemistry with anthropogenic oxidants. This analysis may provide vital information to strengthen legislation as well as to support health studies in order to improve air quality in the UK. Canonaco, F. et al. Atmos Meas Tech. 6, 3649-3661, 2013. Fry, J. et al. Atmos. Chem. Phys. 9, 1431-1449, 2009. Hao, L. Atmos. Chem. Phys., 14, 13483-13495, 2014. Zhao, S. et al. Atmospheric Pollution Research. 5, 335-343, 2014.

  2. A Regional Assessment of Marine Vessel PM2.5 Impacts in the U.S. Pacific Northwest Using a Receptor Based Source Apportionment Method

    EPA Science Inventory

    This work reports the results of a regional receptor-based source apportionment analysis using the Positive Matrix Factorization (PMF) model on chemically speciated PM2.5 data from 36 urban and rural monitoring sites within the U.S. Pacific Northwest. The approach taken is to mo...

  3. Intra-urban biomonitoring: Source apportionment using tree barks to identify air pollution sources.

    PubMed

    Moreira, Tiana Carla Lopes; de Oliveira, Regiani Carvalho; Amato, Luís Fernando Lourenço; Kang, Choong-Min; Saldiva, Paulo Hilário Nascimento; Saiki, Mitiko

    2016-05-01

    It is of great interest to evaluate if there is a relationship between possible sources and trace elements using biomonitoring techniques. In this study, tree bark samples of 171 trees were collected using a biomonitoring technique in the inner city of São Paulo. The trace elements (Al, Ba, Ca, Cl, Cu, Fe, K, Mg, Mn, Na, P, Rb, S, Sr and Zn) were determined by the energy dispersive X-ray fluorescence (EDXRF) spectrometry. The Principal Component Analysis (PCA) was applied to identify the plausible sources associated with tree bark measurements. The greatest source was vehicle-induced non-tailpipe emissions derived mainly from brakes and tires wear-out and road dust resuspension (characterized with Al, Ba, Cu, Fe, Mn and Zn), which was explained by 27.1% of the variance, followed by cement (14.8%), sea salt (11.6%) and biomass burning (10%), and fossil fuel combustion (9.8%). We also verified that the elements related to vehicular emission showed different concentrations at different sites of the same street, which might be helpful for a new street classification according to the emission source. The spatial distribution maps of element concentrations were obtained to evaluate the different levels of pollution in streets and avenues. Results indicated that biomonitoring techniques using tree bark can be applied to evaluate dispersion of air pollution and provide reliable data for the further epidemiological studies.

  4. Occurrence and source apportionment of pharmaceuticals and personal care products in the Beiyun River of Beijing, China.

    PubMed

    Dai, Guohua; Wang, Bin; Huang, Jun; Dong, Rui; Deng, Shubo; Yu, Gang

    2015-01-01

    This work investigates, for the first time, the occurrence and sources of 15 pharmaceuticals and personal care products (PPCPs) in surface water of Beijing, one of most densely populated cities in the world, in three sampling events representing different seasonal flow conditions. The detection frequencies of most PPCPs were in the range of 50-100%. The median concentrations of the selected PPCPs ranged from not detected to 4200 ng L(-1) (caffeine). Generally, higher PPCP levels were observed in early spring, indicating both low flow condition and cold-water temperature might enhance their persistence. Source apportionment showed freshly discharged untreated sewage (67%) significantly contributed to the PPCP burden in the Beiyun River, which provides important information for environmental management.

  5. Water Quality Assessment of River Soan (Pakistan) and Source Apportionment of Pollution Sources Through Receptor Modeling.

    PubMed

    Nazeer, Summya; Ali, Zeshan; Malik, Riffat Naseem

    2016-07-01

    The present study was designed to determine the spatiotemporal patterns in water quality of River Soan using multivariate statistics. A total of 26 sites were surveyed along River Soan and its associated tributaries during pre- and post-monsoon seasons in 2008. Hierarchical agglomerative cluster analysis (HACA) classified sampling sites into three groups according to their degree of pollution, which ranged from least to high degradation of water quality. Discriminant function analysis (DFA) revealed that alkalinity, orthophosphates, nitrates, ammonia, salinity, and Cd were variables that significantly discriminate among three groups identified by HACA. Temporal trends as identified through DFA revealed that COD, DO, pH, Cu, Cd, and Cr could be attributed for major seasonal variations in water quality. PCA/FA identified six factors as potential sources of pollution of River Soan. Absolute principal component scores using multiple regression method (APCS-MLR) further explained the percent contribution from each source. Heavy metals were largely added through industrial activities (28 %) and sewage waste (28 %), nutrients through agriculture runoff (35 %) and sewage waste (28 %), organic pollution through sewage waste (27 %) and urban runoff (17 %) and macroelements through urban runoff (39 %), and mineralization and sewage waste (30 %). The present study showed that anthropogenic activities are the major source of variations in River Soan. In order to address the water quality issues, implementation of effective waste management measures are needed.

  6. Characterization and source apportionment of fine particulate sources at Rijeka, Croatia from 2013 to 2015

    NASA Astrophysics Data System (ADS)

    Ivošević, Tatjana; Stelcer, Eduard; Orlić, Ivica; Bogdanović Radović, Iva; Cohen, David

    2016-03-01

    PM2.5 daily aerosol samples were collected in Rijeka, Croatia during period from 6th August 2013 to 29th January 2015. In total, 259 samples were collected on Teflon filters and analyzed by PIXE and PIGE techniques to give information on 21 elements from Na to Pb. Additionally, black carbon was determined with the Laser Integrated Plate Method. Results were statistically evaluated using Positive Matrix Factorization (PMF). Eight major pollution sources: auto, smoke, secondary sulfates, heavy oil combustion, sea spray, road dust, industry iron and soil dust were identified together with their relative contributions in total PM2.5 pollution.

  7. Impact of gas/particle partitioning of semivolatile organic compounds on source apportionment with positive matrix factorization.

    PubMed

    Xie, Mingjie; Hannigan, Michael P; Barsanti, Kelley C

    2014-08-19

    To quantify and minimize the influence of gas/particle (G/P) partitioning on receptor-based source apportionment using particle-phase semivolatile organic compound (SVOC) data, positive matrix factorization (PMF) coupled with a bootstrap technique was applied to three data sets mainly composed of "measured-total" (measured particle- + gas-phase), "particle-only" (measured particle-phase) and "predicted-total" (measured particle-phase + predicted gas-phase) SVOCs to apportion carbonaceous aerosols. Particle- (PM2.5) and gas-phase SVOCs were collected using quartz fiber filters followed by PUF/XAD-4/PUF adsorbents and measured using gas chromatography-mass spectrometry (GC-MS). Concentrations of gas-phase SVOCs were also predicted from their particle-phase concentrations using absorptive partitioning theory. Five factors were resolved for each data set, and the factor profiles were generally consistent across the three PMF solutions. Using a previous source apportionment study at the same receptor site, those five factors were linked to summertime biogenic emissions (odd n-alkane factor), unburned fossil fuels (light SVOC factor), road dust and/or cooking (n-alkane factor), motor vehicle emissions (PAH factor), and lubricating oil combustion (sterane factor). The "measured-total" solution was least influenced by G/P partitioning and used as reference. Two out of the five factors (odd n-alkane and PAH factors) exhibited consistent contributions for "particle-only" vs "measured-total" and "predicted-total" vs "measured-total" solutions. Factor contributions of light SVOC and n-alkane factors were more consistent for "predicted-total" vs "measured-total" than "particle-only" vs "measured-total" solutions. The remaining factor (sterane factor) underestimated the contribution by around 50% from both "particle-only" and "predicted-total" solutions. The results of this study confirm that when measured gas-phase SVOCs are not available, "predicted-total" SVOCs should be used

  8. Variations in source apportionments of nutrient load among seasons and hydrological years in a semi-arid watershed: GWLF model results.

    PubMed

    Du, Xinzhong; Li, Xuyong; Zhang, Wangshou; Wang, Huiliang

    2014-05-01

    Quantifying source apportionments of nutrient load and their variations among seasons and hydrological years can provide useful information for watershed nutrient load reduction programs. There are large seasonal and inter-annual variations in nutrient loads and their sources in semi-arid watersheds that have a monsoon climate. The Generalized Watershed Loading Function model was used to simulate monthly nutrient loads from 2004 to 2011 in the Liu River watershed, Northern China. Model results were used to investigate nutrient load contributions from different sources, temporal variations of source apportionments and the differences in the behavior of total nitrogen (TN) and total phosphorus (TP). Examination of source apportionments for different seasons showed that point sources were the main source of TN and TP in the non-flood season, whereas contributions from diffuse sources, such as rural runoff, soil erosion, and urban areas, were much higher in the flood season. Furthermore, results for three typical hydrological years showed that the contribution ratios of nutrient loads from point sources increased as streamflow decreased, while contribution ratios from rural runoff and urban area increased as streamflow increased. Further, there were significant differences between TN and TP sources on different time scales. Our findings suggest that priority actions and management measures should be changed for different time periods and hydrological conditions, and that different strategies should be used to reduce loads of nitrogen and phosphorus effectively.

  9. Source apportionment of polycyclic aromatic hydrocarbons in urban air using positive matrix factorization and spatial distribution analysis

    NASA Astrophysics Data System (ADS)

    Jang, Eunhwa; Alam, Mohammed S.; Harrison, Roy M.

    2013-11-01

    Polycyclic aromatic hydrocarbons (PAH) are currently generating a great deal of interest because of their recognised toxicity, including carcinogenicity. In this study, source apportionment (SA) has been carried out using Positive Matrix Factorisation (PMF) with a dataset of 29 individual PAH (sum of vapour and particulate forms) collected by the UK National Network between 2002 and 2006. Analysis of data from 14 urban sites revealed four major source categories corresponding to unburned petroleum, diesel combustion, wood combustion and coal combustion. When a separate set of sites known to be influenced by local industrial sources was analysed, three source categories were identified corresponding to the unburned petroleum, diesel combustion and coal combustion seen in the full data analysis. When SA data were applied to the individual sites, the estimated apportionment could be explained in terms of local emission characteristics. Unburned petroleum showed the highest contribution to the sum of PAH, averaging 51.9% across the network, but benzo(a)pyrene (BaP) was more influenced by the coal combustion source which contributed 59.5% across the entire network. At the subset of sites with local industrial influence, industry was both the main contributor to the sum of PAH (accounting for 48.4% of PAH mass) and of BaP (67.9% of mass). A spatial analysis was also conducted in which the traffic source was evaluated by the difference between a roadside and a nearby urban background site, the urban source by difference between urban background and a rural site, and the industrial source by difference between a site close to a major steelworks subtracting data from a local urban background site. This showed considerable similarity between the net urban contribution and the road traffic factor, and between the net industrial contribution and the PMF coal factor profile. In both cases the congener profiles corresponded fairly well to UK national emissions inventory data

  10. Source Apportionment of Elemental Carbon Across the San Francisco Bay Area Using Combined Radiocarbon and Chemical Mass Balances

    NASA Astrophysics Data System (ADS)

    Yoon, S.; Fairley, D.; Sheesley, R. J.

    2014-12-01

    The San Francisco Bay Area is impacted by ambient particulate matter (PM) from a variety of sources including motor vehicles, biomass burning, off-road vehicles, industry, and meat cooking. Ambient PM, especially fine PM (diameter less than 2.5μm, PM2.5), is known to negatively impact health. Elemental Carbon (EC) is one of the major constituents of PM2.5. It not only negatively affects health but is also a powerful short-lived climate forcer. The State of California and Bay Area Air Quality Management District (BAAQMD) have made efforts in regulating contribution of EC from diesel trucks and wood burning, respectively. These and other efforts have assisted in significantly reducing the annual average PM2.5 concentrations approximately 30% since 2005 and 70% since 1990. Despite these improvements, to better determine the relative contribution of contemporary vs. fossil carbon, radiocarbon source apportionment of EC was conducted on PM2.5 collected in the Bay Area. Measurements of the abundance of 14C in the EC fractions are used to quantify the relative contributions of fossil carbon (fossil fuel combustion, including motor vehicle exhaust) and contemporary carbon (biomass combustion and meat cooking). This comprehensive study included seven sites in the Bay Area and 12 months of sampling starting November 2011 through October 2012. The samples were composited to represent winter (November-February) and non-winter (March-October). In addition to radiocarbon analysis, Chemical Mass Balance (CMB) analysis using bulk PM2.5 composition and selected trace gases was used to understand the split among gasoline, natural gas, and diesel exhaust. Preliminary apportionment of the seven sites shows roughly equal contributions of fossil fuel and biomass burning/cooking for both winter and non-winter samples. There is evidence that the diesel contribution to EC, in particular, has decreased substantially over the last decade.

  11. Evaluation and Source Apportionment of Heavy Metals (HMs) in Sewage Sludge of Municipal Wastewater Treatment Plants (WWTPs) in Shanxi, China

    PubMed Central

    Duan, Baoling; Liu, Fenwu; Zhang, Wuping; Zheng, Haixia; Zhang, Qiang; Li, Xiaomei; Bu, Yushan

    2015-01-01

    Heavy metals (HMs) in sewage sludge have become the crucial limiting factors for land use application. Samples were collected and analyzed from 32 waste water treatment plants (WWTPs) in the Shanxi Province, China. HM levels in sewage sludge were assessed. The multivariate statistical method principal component analysis (PCA) was applied to identify the sources of HMs in sewage sludge. HM pollution classes by geochemical accumulation index Igeo and correlation analyses between HMs were also conducted. HMs were arranged in the following decreasing order of mean concentration: Zn > Cu > Cr > Pb > As > Hg > Cd; the maximum concentrations of all HMs were within the limit of maximum content permitted by Chinese discharge standard. Igeo classes of HMs pollution in order from most polluted to least were: Cu and Hg pollution were the highest; Cd and Cr pollution were moderate; Zn, As and Pb pollution were the least. Sources of HM contamination in sewage sludge were identified as three components. The primary contaminant source accounting for 35.7% of the total variance was identified as smelting industry, coking plant and traffic sources; the second source accounting for 29.0% of the total variance was distinguished as household and water supply pollution; the smallest of the three sources accounting for 16.2% of the total variance was defined as special industries such as leather tanning, textile manufacturing and chemical processing industries. Source apportionment of HMs in sewage sludge can control HM contamination through suggesting improvements in government policies and industrial processes. PMID:26690464

  12. Evaluation and Source Apportionment of Heavy Metals (HMs) in Sewage Sludge of Municipal Wastewater Treatment Plants (WWTPs) in Shanxi, China.

    PubMed

    Duan, Baoling; Liu, Fenwu; Zhang, Wuping; Zheng, Haixia; Zhang, Qiang; Li, Xiaomei; Bu, Yushan

    2015-12-11

    Heavy metals (HMs) in sewage sludge have become the crucial limiting factors for land use application. Samples were collected and analyzed from 32 waste water treatment plants (WWTPs) in the Shanxi Province, China. HM levels in sewage sludge were assessed. The multivariate statistical method principal component analysis (PCA) was applied to identify the sources of HMs in sewage sludge. HM pollution classes by geochemical accumulation index I(geo) and correlation analyses between HMs were also conducted. HMs were arranged in the following decreasing order of mean concentration: Zn > Cu > Cr > Pb > As > Hg > Cd; the maximum concentrations of all HMs were within the limit of maximum content permitted by Chinese discharge standard. I(geo) classes of HMs pollution in order from most polluted to least were: Cu and Hg pollution were the highest; Cd and Cr pollution were moderate; Zn, As and Pb pollution were the least. Sources of HM contamination in sewage sludge were identified as three components. The primary contaminant source accounting for 35.7% of the total variance was identified as smelting industry, coking plant and traffic sources; the second source accounting for 29.0% of the total variance was distinguished as household and water supply pollution; the smallest of the three sources accounting for 16.2% of the total variance was defined as special industries such as leather tanning, textile manufacturing and chemical processing industries. Source apportionment of HMs in sewage sludge can control HM contamination through suggesting improvements in government policies and industrial processes.

  13. A stable isotope approach for source apportionment of chlorinated ethene plumes at a complex multi-contamination events urban site.

    PubMed

    Nijenhuis, Ivonne; Schmidt, Marie; Pellegatti, Eleonora; Paramatti, Enrico; Richnow, Hans Hermann; Gargini, Alessandro

    2013-10-01

    The stable carbon isotope composition of chlorinated aliphatic compounds such as chlorinated methanes, ethanes and ethenes was examined as an intrinsic fingerprint for apportionment of sources. A complex field site located in Ferrara (Italy), with more than 50years history of use of chlorinated aliphatic compounds, was investigated in order to assess contamination sources. Several contamination plumes were found in a complex alluvial sandy multi-aquifer system close to the river Po; sources are represented by uncontained former industrial and municipal dump sites as well as by spills at industrial areas. The carbon stable isotope signature allowed distinguishing 2 major sources of contaminants. One source of chlorinated aliphatic contaminants was strongly depleted in ¹³C (<-60‰) suggesting production lines which have used depleted methane for synthesis. The other source had typical carbon isotope compositions of >-40‰ which is commonly observed in recent production of chlorinated solvents. The degradation processes in the plumes could be traced interpreting the isotope enrichment and depletion of parent and daughter compounds, respectively. We demonstrate that, under specific production conditions, namely when highly chlorinated ethenes are produced as by-product during chloromethanes production, ¹³C depleted fingerprinting of contaminants can be obtained and this can be used to track sources and address the responsible party of the pollution in urban areas.

  14. Size-resolved source apportionment of carbonaceous particulate matter in urban and rural sites in central California

    NASA Astrophysics Data System (ADS)

    Ham, Walter A.; Kleeman, Michael J.

    2011-08-01

    Very little is currently known about the relationship between exposure to different sources of ambient ultrafine particles (PM 0.1) and human health effects. If human health effects are enhanced by PM 0.1's ability to cross cell membranes, then more information is needed describing the sources of ultrafine particles that are deposited in the human respiratory system. The current study presents results for the source apportionment of airborne particulate matter in six size fractions smaller than 1.8 μm particle diameter including ultrafine particles (PM 0.1) in one of the most polluted air basins in the United States. Size-resolved source apportionment results are presented at an urban site and rural site in central California's heavily polluted San Joaquin Valley during the winter and summer months using a molecular marker chemical mass balance (MM-CMB) method. Respiratory deposition calculations for the size-resolved source apportionment results are carried out with the Multiple Path Particle Dosimetry Model ( MPPD v 2.0), including calculations for ultrafine (PM 0.1) source deposition. Diesel engines accounted for the majority of PM 0.1 and PM 1.8 EC at both the urban and rural sampling locations during both summer and winter seasons. Meat cooking accounted for 33-67% and diesel engines accounted for 15-21% of the PM 0.1 OC at Fresno. Meat cooking accounted for 22-26% of the PM 0.1 OC at the rural Westside location, while diesel engines accounted for 8-9%. Wood burning contributions to PM 0.1 OC increased to as much as 12% of PM 0.1 OC during the wintertime. The modest contribution of wood smoke reflects the success of emissions control programs over the past decade. In contrast to PM 0.1, PM 1.8 OC had a higher fraction of unidentified source contributions (68-85%) suggesting that this material is composed of secondary organic aerosol (SOA) or primary organic aerosol (POA) that has been processed by atmospheric chemical reactions. Meat cooking was the largest

  15. Occurrence and source apportionment of Per- and poly-fluorinated compounds (PFCs) in North Canal Basin, Beijing

    NASA Astrophysics Data System (ADS)

    Zhang, Yi-Zhe; Wang, Bin; Wang, Wei; Li, Wen-Chao; Huang, Jun; Deng, Shu-Bo; Wang, Yu-Jue; Yu, Gang

    2016-11-01

    Various per- and poly-fluorinated compounds (PFCs) were first systematically investigated in North Canal Basin, Beijing, China. A total of 68 surface water samples were collected from North Canal Basin, Beijing, at high spatial resolution. The seasonal disparity was compared and associated with source variation. PFCs concentrations in low-water period ranged from 26 to 207 ng/L, and significantly declined levels were found in high-water period. The individual component proportions among different sites varied less in high-water period, when runoff played a role in mixing and diluting PFCs. A methodology combined with principal component analysis (PCA), heat map-hierarchical cluster analysis (HM-HCA), and correlation analysis were introduced to discriminate sources of PFCs in surface water. The statistical results agreed with each other, and daily domestic consumption, fire-fighting products and related industries were identified as sources of PFCs in this region. In addition, two composition ratios were proposed through the methodology to distinguish the impact of nonpoint source, and the outcome demonstrates that great disparities exist in compositional profiles between nonpoint source and others. Overall, the results showed that this comprehensive analysis method has great potential for source apportionment in surface water and other environmental compartments.

  16. Occurrence and source apportionment of Per- and poly-fluorinated compounds (PFCs) in North Canal Basin, Beijing

    PubMed Central

    Zhang, Yi-Zhe; Wang, Bin; Wang, Wei; Li, Wen-Chao; Huang, Jun; Deng, Shu-Bo; Wang, Yu-Jue; Yu, Gang

    2016-01-01

    Various per- and poly-fluorinated compounds (PFCs) were first systematically investigated in North Canal Basin, Beijing, China. A total of 68 surface water samples were collected from North Canal Basin, Beijing, at high spatial resolution. The seasonal disparity was compared and associated with source variation. PFCs concentrations in low-water period ranged from 26 to 207 ng/L, and significantly declined levels were found in high-water period. The individual component proportions among different sites varied less in high-water period, when runoff played a role in mixing and diluting PFCs. A methodology combined with principal component analysis (PCA), heat map-hierarchical cluster analysis (HM-HCA), and correlation analysis were introduced to discriminate sources of PFCs in surface water. The statistical results agreed with each other, and daily domestic consumption, fire-fighting products and related industries were identified as sources of PFCs in this region. In addition, two composition ratios were proposed through the methodology to distinguish the impact of nonpoint source, and the outcome demonstrates that great disparities exist in compositional profiles between nonpoint source and others. Overall, the results showed that this comprehensive analysis method has great potential for source apportionment in surface water and other environmental compartments. PMID:27845351

  17. Radiocarbon apportionment of fossil versus biofuel combustion sources of polycyclic aromatic hydrocarbons in the Stockholm metropolitan area.

    PubMed

    Mandalakis, Manolis; Gustafsson, Orjan; Reddy, Christopher M; Xu, Li

    2004-10-15

    Source-diagnostic markers and the isotopic composition of polycyclic aromatic hydrocarbons (PAHs) were examined in surface sediments from the greater Stockholm waterways to deduce the contribution from biomass sources to the environmental PAH load. The summed concentration of 20 PAHs ranged from 0.8 to 45.1 microg/g (dry weight) and exhibited a steep decline with increasing distance from the city center evidencing that sources within the metropolitan area of Stockholm dominate its PAH burden. Several diagnostic PAH ratios indicated an overwhelming predominance of pyrogenic sources over the petrogenic ones, while retene and 1,7-dimethylphenanthrene were unable to correctly evaluate the contribution from biomass combustion. The stable carbon isotope composition (delta13C) of individual PAHs ranged from -24.8 to -27.0% but also was proved inefficient to discriminate between different types of fuels due to the overlapping signals in various sources. The delta14C values of PAHs ranged between -550.4 and -934.1%, indicating a clear predominance of fossil fuel sources. By using an isotopic mass balance approach, we estimated that on average 17+/-9% of PAHs derived from biomass combustion. This radiocarbon apportionment, in conjunction with detailed energy statistics for the Stockholm region, revealed that the ambient PAH burden is roughly similar, per unit energy produced, from fossil fuels and biofuels. Societies' shifting energy policies toward a larger reliance on biofuels may thus not lead to further deterioration of air quality and respiratory ailments for the urban population.

  18. Isotope-Based Source Apportionment of EC Aerosol Particles during Winter High-Pollution Events at the Zeppelin Observatory, Svalbard.

    PubMed

    Winiger, Patrik; Andersson, August; Yttri, Karl E; Tunved, Peter; Gustafsson, Örjan

    2015-10-06

    Black carbon (BC) aerosol particles contribute to climate warming of the Arctic, yet both the sources and the source-related effects are currently poorly constrained. Bottom-up emission inventory (EI) approaches are challenged for BC in general and the Arctic in particular. For example, estimates from three different EI models on the fractional contribution to BC from biomass burning (north of 60° N) vary between 11% and 68%, each acknowledging large uncertainties. Here we present the first dual-carbon isotope-based (Δ(14)C and δ(13)C) source apportionment of elemental carbon (EC), the mass-based correspondent to optically defined BC, in the Arctic atmosphere. It targeted 14 high-loading and high-pollution events during January through March of 2009 at the Zeppelin Observatory (79° N; Svalbard, Norway), with these representing one-third of the total sampling period that was yet responsible for three-quarters of the total EC loading. The top-down source-diagnostic (14)C fingerprint constrained that 52 ± 15% (n = 12) of the EC stemmed from biomass burning. Including also two samples with 95% and 98% biomass contribution yield 57 ± 21% of EC from biomass burning. Significant variability in the stable carbon isotope signature indicated temporally shifting emissions between different fossil sources, likely including liquid fossil and gas flaring. Improved source constraints of Arctic BC both aids better understanding of effects and guides policy actions to mitigate emissions.

  19. A framework of characteristics identification and source apportionment of water pollution in a river: a case study in the Jinjiang River, China.

    PubMed

    Chen, Haiyang; Teng, Yanguo; Wang, Jinsheng

    2012-01-01

    A framework for characteristics identification and source apportionment of water pollution in the Jinjiang River of China was proposed in this study for evaluation. A total of 114 water samples which were generated between May 2009 and September 2010 at 13 sites were collected and analysed. First, support vector machine (SVM) and water quality pollutant index (WQPI) were used for water quality comprehensive evaluation and identifying characteristic contaminants. Later, factor analysis with nonnegative constraints (FA-NNC) was employed for source apportionment. Finally, multi-linear regression of the absolute principal component score (APCS/MLR) was applied to further estimate source contributions for each characteristic contaminant. The results indicated that the water quality of the Jinjiang River was mainly at the third level (65.79%) based on national surface water quality permissible standards in China. Ammonia nitrogen, total phosphorus, mercury, iron and manganese were identified as characteristic contaminants. Source apportionment results showed that industrial activities (63.16%), agricultural non-point source (16.50%) and domestic sewage (12.85%) were the main anthropogenic pollution sources which were influencing the water quality of Jinjiang River. This proposed method provided a helpful framework for conducting water pollution management in aquatic environment.

  20. Distribution and source apportionment of polycyclic aromatic hydrocarbons in surface sediments from Zhoushan Archipelago and Xiangshan Harbor, East China Sea.

    PubMed

    Wang, Xiaoyan; Xu, Huanzhi; Zhou, Yongdong; Wu, Changwen; Kanchanopas-Barnette, Praparsiri

    2015-12-30

    Zhoushan Archipelago and the adjacent Xiangshan Harbor are important commercial, tourism, fishing, and mariculture areas. Considering the concern on the effects of anthropogenic activities on the environment, the level and source apportionment of polycyclic aromatic hydrocarbons (PAHs) in surface sediments were investigated. The sum of 16 PAH (∑16 PAH) concentrations in the Zhoushan Archipelago ranged from 3.67 to 31.30 ng g(-1) d.w., with a mean of 15.01 ± 1.21 ng g(-1) d.w., and that in Xiangshan Harbor varied from 11.58 to 481.44 ng g(-1) d.w., with a mean of 62.52 ± 32.85 ng g(-1) d.w. Diagnostic ratios and factor analysis were performed to identify PAH sources. Results show that PAHs have mixed origins (i.e., traffic-related sources, coal combustion, petrogenic sources, and biomass burning), with pyrolytic-related pollution as the dominant source. This study provided a baseline to promote environmental protection and pollution episode monitoring in the East China Sea.

  1. Positive matrix factorization as source apportionment of soil lead and cadmium around a battery plant (Changxing County, China).

    PubMed

    Xue, Jian-long; Zhi, Yu-you; Yang, Li-ping; Shi, Jia-chun; Zeng, Ling-zao; Wu, Lao-sheng

    2014-06-01

    Chemical compositions of soil samples are multivariate in nature and provide datasets suitable for the application of multivariate factor analytical techniques. One of the analytical techniques, the positive matrix factorization (PMF), uses a weighted least square by fitting the data matrix to determine the weights of the sources based on the error estimates of each data point. In this research, PMF was employed to apportion the sources of heavy metals in 104 soil samples taken within a 1-km radius of a lead battery plant contaminated site in Changxing County, Zhejiang Province, China. The site is heavily contaminated with high concentrations of lead (Pb) and cadmium (Cd). PMF successfully partitioned the variances into sources related to soil background, agronomic practices, and the lead battery plants combined with a geostatistical approach. It was estimated that the lead battery plants and the agronomic practices contributed 55.37 and 29.28%, respectively, for soil Pb of the total source. Soil Cd mainly came from the lead battery plants (65.92%), followed by the agronomic practices (21.65%), and soil parent materials (12.43%). This research indicates that PMF combined with geostatistics is a useful tool for source identification and apportionment.

  2. An integrated SOM-based multivariate approach for spatio-temporal patterns identification and source apportionment of pollution in complex river network.

    PubMed

    Yang, Yonghui; Wang, Cuiyu; Guo, Huaicheng; Sheng, Hu; Zhou, Feng

    2012-09-01

    In this study, three classification techniques (self-organizing maps, hierarchical cluster analysis and discriminant analysis) were applied to identify spatial water pollution levels, temporal water quality response delay phenomena (WQRDP), source pollution types (point, urban non-point, or agricultural non-point). Two models (principal components analysis (PCA), and positive matrix factorization (PMF)) were used to do the further quantitative source apportionment studying. The 27 inflow rivers in spatial were divided into three pollution levels (A, high; B, medium; C, low). The primary pollution pattern in spatial Clusters A, B, and C were point, urban non-point and agricultural non-point separately, in consideration of simultaneous land use types. Source apportionment results identified five typical factors in spatial Cluster A and six typical factors in spatial Cluster B and C as responsible for the data structure, explaining 80%-90% of the total variance of the dataset.

  3. Source apportionment of PM2.5 in top polluted cities in Hebei, China using the CMAQ model

    NASA Astrophysics Data System (ADS)

    Wang, Litao; Wei, Zhe; Wei, Wei; Fu, Joshua S.; Meng, Chenchen; Ma, Simeng

    2015-12-01

    Hebei has been recognized as one of the most polluted provinces in China, characterized by extremely high concentrations of fine particulate matter (PM2.5) in many of its cities, especially those located in the southern area of the province and highly potentially northward transported to Beijing. Source apportionment of PM2.5 is the basis and prerequisite of an effective control strategy. In this study, the Mesoscale Modeling System Generation 5 (MM5) and the Models-3/Community Multiscale Air Quality (CMAQ) modeling system are applied to East Asia and North China at 36- and 12-km horizontal grid resolutions, and the source apportionment of PM2.5 in the three top polluted cities in Hebei, i.e., Shijiazhuang, Xingtai, and Handan, is performed using the Brute-Force method. It is concluded that the regional source contributions to PM2.5 are 27.9% in Shijiazhuang, 46.6% in Xingtai, and 40.4% in Handan. The major local contributors are industrial, domestic and agricultural sources in all the three cities with the contributions of 39.8%, 15.8%, and 10.6% in Shijiazhuang, 30.5%, 13.6%, and 6.9% in Xingtai, 35.9%, 13.5%, and 6.2% in Handan, respectively. As to the secondary aerosols of sulfate (SO42-), nitrate (NO3-), and ammonium (NH4+) in PM2.5, which are important chemical species in PM2.5 (about 30-40% in PM2.5) and cannot be further apportioned by receptor models, the regional source contributions to the total concentrations of SO42-, NO3-, and NH4+ are 40.9%, 62.0%, and 59.1% in Shijiazhuang, Xingtai, and Handan, respectively. The local industrial, domestic and agricultural contributions to those are 23.7%, 6.6%, and 29.8% in total in Shijiazhuang, 17.5%, 5.0%, and 17.7% in Xingtai, and 20.6%, 4.8%, and 17.8% in Handan, respectively. The regional joint controls of air pollution are more important in Xingtai and Handan than in Shijiazhuang, and the emission controls of agricultural sources need to be further considered in the future policy.

  4. Characterization and source apportionment of health risks from ambient PM10 in Hong Kong over 2000-2011

    NASA Astrophysics Data System (ADS)

    Li, Zhiyuan; Yuan, Zibing; Li, Ying; Lau, Alexis K. H.; Louie, Peter K. K.

    2015-12-01

    Atmospheric particulate matter (PM) pollution is a major public health concern in Hong Kong. In this study, the spatiotemporal variations of health risks from ambient PM10 from seven air quality monitoring stations between 2000 and 2011 were analyzed. Positive matrix factorization (PMF) was adopted to identify major source categories of ambient PM10 and quantify their contributions. Afterwards, a point-estimated risk model was used to identify the inhalation cancer and non-cancer risks of PM10 sources. The long-term trends of the health risks from classified local and non-local sources were explored. Furthermore, the reason for the increase of health risks during high PM10 days was discussed. Results show that vehicle exhaust source was the dominant inhalation cancer risk (ICR) contributor (72%), whereas trace metals and vehicle exhaust sources contributed approximately 27% and 21% of PM10 inhalation non-cancer risk (INCR), respectively. The identified local sources accounted for approximately 80% of the ICR in Hong Kong, while contribution percentages of the non-local and local sources for INCR are comparable. The clear increase of ICR at high PM days was mainly attributed to the increase of contributions from coal combustion/biomass burning and secondary sulfate, while the increase of INCR at high PM days was attributed to the increase of contributions from the sources coal combustion/biomass burning, secondary nitrate, and trace metals. This study highlights the importance of health risk-based source apportionment in air quality management with protecting human health as the ultimate target.

  5. Bioavailability of Polycyclic Aromatic Hydrocarbons and their Potential Application in Eco-risk Assessment and Source Apportionment in Urban River Sediment

    NASA Astrophysics Data System (ADS)

    Yang, Xunan; Yu, Liuqian; Chen, Zefang; Xu, Meiying

    2016-03-01

    Traditional risk assessment and source apportionment of sediments based on bulk polycyclic aromatic hydrocarbons (PAHs) can introduce biases due to unknown aging effects in various sediments. We used a mild solvent (hydroxypropyl-β-cyclodextrin) to extract the bioavailable fraction of PAHs (a-PAHs) from sediment samples collected in Pearl River, southern China. We investigated the potential application of this technique for ecological risk assessments and source apportionment. We found that the distribution of PAHs was associated with human activities and that the a-PAHs accounted for a wide range (4.7%–21.2%) of total-PAHs (t-PAHs), and high risk sites were associated with lower t-PAHs but higher a-PAHs. The correlation between a-PAHs and the sediment toxicity assessed using tubificid worms (r = ‑0.654, P = 0.021) was greater than that from t-PAH-based risk assessment (r = ‑0.230, P = 0.472). Moreover, the insignificant correlation between a-PAH content and mPEC-Q of low molecular weight PAHs implied the potiential bias of t-PAH-based risk assessment. The source apportionment from mild extracted fractions was consistent across different indicators and was in accordance with typical pollution sources. Our results suggested that mild extraction-based approaches reduce the potential error from aging effects because the mild extracted PAHs provide a more direct indicator of bioavailability and fresher fractions in sediments.

  6. Online coupling of pure O2 thermo-optical methods - 14C AMS for source apportionment of carbonaceous aerosols

    NASA Astrophysics Data System (ADS)

    Agrios, Konstantinos; Salazar, Gary; Zhang, Yan-Lin; Uglietti, Chiara; Battaglia, Michael; Luginbühl, Marc; Ciobanu, Viorela Gabriela; Vonwiller, Matthias; Szidat, Sönke

    2015-10-01

    This paper reports on novel separation methods developed for the direct determination of 14C in organic carbon (OC) and elemental carbon (EC), two sub-fractions of total carbon (TC) of atmospheric air particulate matter. Until recently, separation of OC and EC has been performed off-line by manual and time-consuming techniques that relied on the collection of massive CO2 fractions. We present here two on-line hyphenated techniques between a Sunset OC/EC analyzer and a MICADAS (MIni radioCArbon DAting System) accelerator mass spectrometer (AMS) equipped with a gas ion source. The first implementation facilitates the direct measurement in the low sample size range (<10 μg C) with high throughput on a routine basis, while the second explores the potential for a continuous-flow real-time CO2 gas feed into the ion source. The performance achieved with reference materials and real atmospheric samples will be discussed to draw conclusions on the improvement offered in the field of 14C aerosol source apportionment.

  7. Source Apportionment of PM10-Bound Polycyclic Aromatic Hydrocarbons by Positive Matrix Factorization in Córdoba City, Argentina.

    PubMed

    Amarillo, Ana C; Mateos, Ana C; Carreras, Hebe

    2017-04-01

    The composition and concentration of polycyclic aromatic hydrocarbons (PAHs) adsorbed on particles smaller than 10 microns (PM10) were analyzed in an urban area during a 2-year period from August 2011 to August 2013. Diagnostic ratios (DR) and positive matrix factorization (PMF) were employed to assess emission sources. To discount weather influence, a multiple linear regression model was generated and also a photodecomposition index was calculated for each sample. Despite the fact that mean PM10 levels showed a similar pattern all around the year, majority of PAHs showed higher concentrations during the cold than the warm period, indicating a strong seasonal variation. A 38% of PAHs variation could be explained by meteorological variables, with wind speed, wind direction, and dew point being the significant regressor variables in the model. The source apportionment of PAHs was performed using PMF although they are photosensitive compounds. The sampling period was separated in warm and cold seasons according to a photodecomposition index and cold period was used. Also, DR were calculated. DR as well as PMF analysis suggested that both gasoline and diesel vehicular emissions are the main PAHs emission sources in this urban area.

  8. Heavy metal contamination of surface soil in electronic waste dismantling area: site investigation and source-apportionment analysis.

    PubMed

    Jinhui Li; Huabo Duan; Pixing Shi

    2011-07-01

    The dismantling and disposal of electronic waste (e-waste) in developing countries is causing increasing concern because of its impacts on the environment and risks to human health. Heavy-metal concentrations in the surface soils of Guiyu (Guangdong Province, China) were monitored to determine the status of heavy-metal contamination on e-waste dismantling area with a more than 20 years history. Two metalloids and nine metals were selected for investigation. This paper also attempts to compare the data among a variety of e-waste dismantling areas, after reviewing a number of heavy-metal contamination-related studies in such areas in China over the past decade. In addition, source apportionment of heavy metal in the surface soil of these areas has been analysed. Both the MSW open-burning sites probably contained invaluable e-waste and abandoned sites formerly involved in informal recycling activities are the new sources of soil-based environmental pollution in Guiyu. Although printed circuit board waste is thought to be the main source of heavy-metal emissions during e-waste processing, requirement is necessary to soundly manage the plastic separated from e-waste, which mostly contains heavy metals and other toxic substances.

  9. Source apportionment of ambient fine particulate matter in Dearborn, Michigan, using hourly resolved PM chemical composition data.

    PubMed

    Pancras, Joseph Patrick; Landis, Matthew S; Norris, Gary A; Vedantham, Ram; Dvonch, J Timothy

    2013-03-15

    High time-resolution aerosol sampling was conducted for one month during July-August 2007 in Dearborn, MI, a non-attainment area for fine particulate matter (PM2.5) National Ambient Air Quality Standards (NAAQS). Measurements of more than 30 PM2.5 species were made using a suite of semi-continuous sampling and monitoring instruments. Dynamic variations in the sub-hourly concentrations of source 'marker' elements were observed when discrete plumes from local sources impacted the sampling site. Hourly averaged PM2.5 composition data for 639 samples were used to identify and apportion PM2.5 emission sources using the multivariate receptor modeling techniques EPA Positive Matrix Factorization (PMF) v4.2 and EPA Unmix v6.0. Source contribution estimates from PMF and Unmix were then evaluated using the Sustained Wind Instance Method (SWIM), which identified plausible source origins. Ten sources were identified by both PMF and Unmix: (1) secondary sulfate, (2) secondary nitrate characterized by a significant diurnal trend, (3) iron and steel production, (4) a potassium-rich factor attributable to iron/steel slag waste processing, (5) a cadmium-rich factor attributable to incineration, (6) an oil refinery characterized by La/Ce>1 specific to south wind, (7) oil combustion, (8) coal combustion, (9) motor vehicles, and (10) road dust enriched with organic carbon. While both models apportioned secondary sulfate, oil refinery, and oil combustion PM2.5 masses closely, the mobile and industrial source apportionments differed. Analyses were also carried out to help infer time-of-day variations in the contributions of local sources.

  10. European isotopic signatures for lead in atmospheric aerosols: a source apportionment based upon 206Pb/207Pb ratios.

    PubMed

    Flament, Pascal; Bertho, Marie-Laure; Deboudt, Karine; Véron, Alain; Puskaric, Emile

    2002-09-16

    To investigate the capability of the lead isotope signature technique to support a source apportionment study at a Continental scale, atmospheric particulate matter was collected at Cap Gris-Nez (Eastern Channel, northern France), over one year (1995-1996). Four days retrospective trajectories of air masses were available during each sampling experiment. Twenty-eight samples, for which the origin of aerosols was unambiguously determined, were selected for isotopic measurements. Considering the Enrichment Factors, EF(Crust) of lead and its size distribution, we show that lead is mostly from anthropogenic origin and mainly associated with [0.4 < diameter < 0.9 microm] particles. The extent to which various Continental sources influence the lead abundance in aerosols is exhibited by considering both the lead concentration and the origin of air masses. Lead concentration is higher by a factor of approximately seven, when air masses are derived from Continental Europe, by comparison with marine air masses. Taking into account these concentrations and the vertical movements of air masses, we compare the different isotopic compositions using a statistical non-parametric test (Kolmogorov-Smirnov). We produce evidence that, for most of the cases, air masses originating from Continental Europe exhibit a more radiogenic composition (1.134 < 206Pb/207Pb < 1.172) than air masses coming from the United Kingdom (1.106 < 206Pb/207Pb < 1.124). Generally, lead isotopic compositions in aerosols are clearly distinct from the gasoline signatures in European countries, strongly suggesting that automotive lead is no longer the major component of this metal in the air. Gasoline and industrial isotopic signatures could explain the origin of lead in our aerosol samples. A source apportionment based upon 206Pb/207Pb ratios, suggests that the difference between British (206Pb/207Pb = 1.122 +/- 0.038) and Continental (206Pb/207Pb = 1.155 +/- 0.022) signatures may be largely explained by

  11. Levels and source apportionment of children's lead exposure: could urinary lead be used to identify the levels and sources of children's lead pollution?

    PubMed

    Cao, Suzhen; Duan, Xiaoli; Zhao, Xiuge; Wang, Beibei; Ma, Jin; Fan, Delong; Sun, Chengye; He, Bin; Wei, Fusheng; Jiang, Guibin

    2015-04-01

    As a highly toxic heavy metal, the pollution and exposure risks of lead are of widespread concern for human health. However, the collection of blood samples for use as an indicator of lead pollution is not always feasible in most cohort or longitudinal studies, especially those involving children health. To evaluate the potential use of urinary lead as an indicator of exposure levels and source apportionment, accompanying with environmental media samples, lead concentrations and isotopic measurements (expressed as (207)Pb/(206)Pb, (208)Pb/(206)Pb and (204)Pb/(206)Pb) were investigated and compared between blood and urine from children living in the vicinities of a typical coking plant and lead-acid battery factory. The results showed urinary lead might not be a preferable proxy for estimating blood lead levels. Fortunately, urinary lead isotopic measurements could be used as an alternative for identifying the sources of children's lead exposure, which coincided well with the blood lead isotope ratio analysis.

  12. Organic aerosol source apportionment in London 2013 with ME-2: exploring the solution space with annual and seasonal analysis

    NASA Astrophysics Data System (ADS)

    Reyes-Villegas, Ernesto; Green, David C.; Priestman, Max; Canonaco, Francesco; Coe, Hugh; Prévôt, André S. H.; Allan, James D.

    2016-12-01

    The multilinear engine (ME-2) factorization tool is being widely used following the recent development of the Source Finder (SoFi) interface at the Paul Scherrer Institute. However, the success of this tool, when using the a value approach, largely depends on the inputs (i.e. target profiles) applied as well as the experience of the user. A strategy to explore the solution space is proposed, in which the solution that best describes the organic aerosol (OA) sources is determined according to the systematic application of predefined statistical tests. This includes trilinear regression, which proves to be a useful tool for comparing different ME-2 solutions. Aerosol Chemical Speciation Monitor (ACSM) measurements were carried out at the urban background site of North Kensington, London from March to December 2013, where for the first time the behaviour of OA sources and their possible environmental implications were studied using an ACSM. Five OA sources were identified: biomass burning OA (BBOA), hydrocarbon-like OA (HOA), cooking OA (COA), semivolatile oxygenated OA (SVOOA) and low-volatility oxygenated OA (LVOOA). ME-2 analysis of the seasonal data sets (spring, summer and autumn) showed a higher variability in the OA sources that was not detected in the combined March-December data set; this variability was explored with the triangle plots f44 : f43 f44 : f60, in which a high variation of SVOOA relative to LVOOA was observed in the f44 : f43 analysis. Hence, it was possible to conclude that, when performing source apportionment to long-term measurements, important information may be lost and this analysis should be done to short periods of time, such as seasonally. Further analysis on the atmospheric implications of these OA sources was carried out, identifying evidence of the possible contribution of heavy-duty diesel vehicles to air pollution during weekdays compared to those fuelled by petrol.

  13. Development and evaluation of a daily temporal interpolation model for fine particulate matter species concentrations and source apportionment

    NASA Astrophysics Data System (ADS)

    Redman, Jeremiah D.; Holmes, Heather A.; Balachandran, Sivaraman; Maier, Marissa L.; Zhai, Xinxin; Ivey, Cesunica; Digby, Kyle; Mulholland, James A.; Russell, Armistead G.

    2016-09-01

    The impacts of emissions sources on air quality in St. Louis, Missouri are assessed for use in acute health effects studies. However, like many locations in the United States, the speciated particulate matter (PM) measurements from regulatory monitoring networks in St. Louis are only available every third day. The power of studies investigating acute health effects of air pollution is reduced when using one-in-three day source impacts compared to daily source impacts. This paper presents a temporal interpolation model to estimate daily speciated PM2.5 mass concentrations and source impact estimates using one-in-three day measurements. The model is used to interpolate 1-in-3 day source impact estimates and to interpolate the 1-in-3 day PM species concentrations prior to source apportionment (SA). Both approaches are compared and evaluated using two years (June 2001-May 2003) of daily data from the St. Louis Midwest Supersite (STL-SS). Data withholding is used to simulate a 1-in-3 day data set from the daily data to evaluate interpolated estimates. After evaluation using the STL-SS data, the model is used to estimate daily source impacts at another site approximately seven kilometers (7 km) northwest of the STL-SS (Blair); results between the sites are compared. For interpolated species concentrations, the model performs better for secondary species (sulfate, nitrate, ammonium, and organic carbon) than for primary species (metals and elemental carbon), likely due to the greater spatial autocorrelation of secondary species. Pearson correlation (R) values for sulfate, nitrate, ammonium, elemental carbon, and organic carbon ranged from 0.61 (elemental carbon, EC2) to 0.97 (sulfate). For trace metals, the R values ranged from 0.31 (Ba) to 0.81 (K). The interpolated source impact estimates also indicated a stronger correlation for secondary sources. Correlations of the secondary source impact estimates based on measurement data and interpolation data ranged from 0.68 to 0

  14. Wood burning pollution in southern Chile: PM2.5 source apportionment using CMB and molecular markers.

    PubMed

    Villalobos, Ana M; Barraza, Francisco; Jorquera, Héctor; Schauer, James J

    2017-03-16

    Temuco is a mid-size city representative of severe wood smoke pollution in southern Chile; i.e., ambient 24-h PM2.5 concentrations have exceeded 150 μg/m(3) in the winter season and the top concentration reached 372 μg/m(3) in 2010. Annual mean concentrations have decreased but are still above 30 μg/m(3). For the very first time, a molecular marker source apportionment of ambient organic carbon (OC) and PM2.5 was conducted in Temuco. Primary resolved sources for PM2.5 were wood smoke (37.5%), coal combustion (4.4%), diesel vehicles (3.3%), dust (2.2%) and vegetative detritus (0.7%). Secondary inorganic PM2.5 (sulfates, nitrates and ammonium) contributed 4.8% and unresolved organic aerosols (generated from volatile emissions from incomplete wood combustion), including secondary organic aerosols, contributed 47.1%. Adding the contributions of unresolved organic aerosols to those from primary wood smoke implies that wood burning is responsible for 84.6% of the ambient PM2.5 in Temuco. This predominance of wood smoke is ultimately due to widespread poverty and a lack of efficient household heating methods. The government has been implementing emission abatement policies but achieving compliance with ambient air quality standards for PM2.5 in southern Chile remains a challenge.

  15. Bias and association of sediment organic matter source apportionment indicators: A case study in a eutrophic Lake Chaohu, China.

    PubMed

    Xu, Fu-Liu; Yang, Chen; He, Wei; He, Qi-Shuang; Li, Yi-Long; Kang, Lei; Liu, Wen-Xiu; Xiong, Yong-Qiang; Xing, Baoshan

    2017-03-01

    The sources of sediment organic matter (SOM) could be explained by various indicators. To test their biases and associations, the present study determined multiple indicators for SOM source apportionment, including elemental analysis (carbon and nitrogen, and their stable isotope δ(13)C and δ(15)N), n-alkanes compositions as well as derivative indicators (e.g., terrigenous to aquatic ratio), and carbon isotopes of n-alkane in Lake Chaohu, a eutrophic lake. The spatial variation of anthropogenic effects could be revealed by SOM elemental variations. The n-alkanes of all samples had a bimodal distribution with the 1st peak at n-alkane with 17 carbons (C17) and the 2nd predominant peak at C29. The parity advantage index of n-alkanes indicated that the sediments had mixed characteristics of both endogenous and terrigenous sources. Some n-alkanes indicators also revealed eutrophication characteristics of dominant algae in Lake Chaohu. SOM received a mixed contribution of plankton (I), low-latitude terrestrial high-grade plants (II) and microbial material (III) as indicated by isotopic compositions of long-chain n-alkane. Multiport element model (MEM) showed the contribution of self-generated sources of organic matter in Lake Chaohu is >50%, indicating the historic serious eutrophication in Lake Chaohu. The main sources of SOM in the eastern part of the lake were algae and terrestrial input, with little input from microbes, and the contribution from algae decreased from west to east. The multiple indicators' judgment by MEM and principle component analysis (PCA) was of ecological significance and proposed because they offered scientific tools for disclosing the historic variations of SOM as well as their sources.

  16. Fine particulates over South Asia: Review and meta-analysis of PM2.5 source apportionment through receptor model.

    PubMed

    Singh, Nandita; Murari, Vishnu; Kumar, Manish; Barman, S C; Banerjee, Tirthankar

    2017-04-01

    Fine particulates (PM2.5) constitute dominant proportion of airborne particulates and have been often associated with human health disorders, changes in regional climate, hydrological cycle and more recently to food security. Intrinsic properties of particulates are direct function of sources. This initiates the necessity of conducting a comprehensive review on PM2.5 sources over South Asia which in turn may be valuable to develop strategies for emission control. Particulate source apportionment (SA) through receptor models is one of the existing tool to quantify contribution of particulate sources. Review of 51 SA studies were performed of which 48 (94%) were appeared within a span of 2007-2016. Almost half of SA studies (55%) were found concentrated over few typical urban stations (Delhi, Dhaka, Mumbai, Agra and Lahore). Due to lack of local particulate source profile and emission inventory, positive matrix factorization and principal component analysis (62% of studies) were the primary choices, followed by chemical mass balance (CMB, 18%). Metallic species were most regularly used as source tracers while use of organic molecular markers and gas-to-particle conversion were minimum. Among all the SA sites, vehicular emissions (mean ± sd: 37 ± 20%) emerged as most dominating PM2.5 source followed by industrial emissions (23 ± 16%), secondary aerosols (22 ± 12%) and natural sources (20 ± 15%). Vehicular emissions (39 ± 24%) also identified as dominating source for highly polluted sites (PM2.5>100 μgm(-3), n = 15) while site specific influence of either or in combination of industrial, secondary aerosols and natural sources were recognized. Source specific trends were considerably varied in terms of region and seasonality. Both natural and industrial sources were most influential over Pakistan and Afghanistan while over Indo-Gangetic plain, vehicular, natural and industrial emissions appeared dominant. Influence of vehicular emission was found

  17. Characterization of PM2.5 in Guangzhou, China: uses of organic markers for supporting source apportionment.

    PubMed

    Wang, Jingzhi; Ho, Steven Sai Hang; Ma, Shexia; Cao, Junji; Dai, Wenting; Liu, Suixin; Shen, Zhenxing; Huang, Rujin; Wang, Gehui; Han, Yongming

    2016-04-15

    Organic carbon (OC), elemental carbon (EC), and non-polar organic compounds including n-alkanes (n-C14-n-C40), polycyclic aromatic hydrocarbons (PAHs), phthalate esters (PAEs) and hopanes were quantified in fine particulate (PM2.5), which were collected in urban area of Guangzhou, China in winter and summer in 2012/2013. The pollutants levels were well comparable with the data obtained in previous studies in Pearl River Delta (PRD) region but much lower than most northern Chinese megacities. The contribution of EC to PM2.5 and OC/EC ratio suggest that the pollution sources were relatively consistent in GZ between the two seasons. Benzo[a]pyrene (BaP) was the most abundant PAHs, which were 4.9 and 1.0ng/m(3) on average, accounting for 10.7% and 9.1% to the total quantified PAHs in winter and summer, respectively. The total concentrations of PAEs ranged from 289.1 to 2435ng/m(3) and from 102.4 to 1437ng/m(3), respectively, in winter and summer. Di-n-butyl phthalate (DBP) was the most dominant PAEs. The ambient levels of PAEs could be partly attributed to the widespread uses of the household products, municipal garbage compressing, sewage, and external painting material on the building. Source apportionment for OC with chemical mass balance (CMB) model demonstrated coal combustion, vehicle emission, cooking, and secondary organic compounds (SOC) formation were the four major pollution sources. Both of the indices of n-alkanes and diagnostic PAHs ratios support that anthropogenic sources such as vehicle emission and coal combustion were the significant pollution sources with some extents from epicuticular waxes by terrestrial plants. The ratio of hopanes to EC proved the influences from vehicle emission, and displayed a certain degree of the air aging in the Guangzhou ambient air.

  18. Measurements and source apportionment of particle-associated polycyclic aromatic hydrocarbons in ambient air in Riyadh, Saudi Arabia

    NASA Astrophysics Data System (ADS)

    Bian, Qijing; Alharbi, Badr; Collett, Jeffrey; Kreidenweis, Sonia; Pasha, Mohammad J.

    2016-07-01

    Ambient air samples were obtained in Riyadh, the capital and largest city of Saudi Arabia, during two measurement campaigns spanning September 2011 to September 2012. Sixteen particle-phase polycyclic aromatic hydrocarbons (PAH) were quantified in 167 samples. Pyrene and fluoranthene were the most abundant PAH, with average of 3.37 ± 14.01 ng m-3 and 8.00 ± 44.09 ng m-3, respectively. A dominant contribution from low molecular weight (LMW) PAH (MW < 228) suggested a large influence of industrial emissions on PAH concentrations. Monte Carlo source apportionment using diagnostic ratios showed that 80 ± 10% of the average LMW PAH concentrations were contributed by petroleum vapor emissions, while 53 ± 19% of high molecular weight (HMW) PAH were from solid fuel combustion emissions. The positive matrix factorization model estimated that oil combustion emissions dominated total PAH concentrations, accounting for on average 96%, likely due to widespread use of oil fuels in energy production (power plants and industries). Our results demonstrate the significant influence of petroleum product production and consumption on particulate-phase PAH concentrations in Riyadh, but also point to the importance of traffic and solid fuel burning, including coke burning and seasonal biomass burning, especially as they contribute to the ambient levels of HMW PAH.

  19. Integrated Application of Multivariate Statistical Methods to Source Apportionment of Watercourses in the Liao River Basin, Northeast China

    PubMed Central

    Chen, Jiabo; Li, Fayun; Fan, Zhiping; Wang, Yanjie

    2016-01-01

    Source apportionment of river water pollution is critical in water resource management and aquatic conservation. Comprehensive application of various GIS-based multivariate statistical methods was performed to analyze datasets (2009–2011) on water quality in the Liao River system (China). Cluster analysis (CA) classified the 12 months of the year into three groups (May–October, February–April and November–January) and the 66 sampling sites into three groups (groups A, B and C) based on similarities in water quality characteristics. Discriminant analysis (DA) determined that temperature, dissolved oxygen (DO), pH, chemical oxygen demand (CODMn), 5-day biochemical oxygen demand (BOD5), NH4+–N, total phosphorus (TP) and volatile phenols were significant variables affecting temporal variations, with 81.2% correct assignments. Principal component analysis (PCA) and positive matrix factorization (PMF) identified eight potential pollution factors for each part of the data structure, explaining more than 61% of the total variance. Oxygen-consuming organics from cropland and woodland runoff were the main latent pollution factor for group A. For group B, the main pollutants were oxygen-consuming organics, oil, nutrients and fecal matter. For group C, the evaluated pollutants primarily included oxygen-consuming organics, oil and toxic organics. PMID:27775679

  20. Measurement and apportionment of radon source terms for modeling indoor environments. Final progress report, March 1990--August 1992

    SciTech Connect

    Harley, N.H.

    1992-12-31

    During the present 2 1/2 year contract period, we have made significant Progress in modeling the source apportionment of indoor {sup 222}Rn and in {sup 222}Rn decay product dosimetry. Two additional areas were worked on which we believe are useful for the DOE Radon research Program. One involved an analysis of the research house data, grouping the hourly house {sup 222}Rn measurements into 2 day, 7 day and 90 day intervals to simulate the response of passive monitors. Another area requiring some attention resulted in a publication of 3 years of our indoor/outdoor measurements in a high-rise apartment. Little interest has been evinced in apartment measurements yet 20% of the US population lives in multiple-family dwellings, not in contact with the ground. These data together with a summary of all other published data on apartments showed that apartments have only about 50% greater {sup 222}Rn concentration than the measured outdoor {sup 222}Rn. Apartment dwellers generally represent a low risk group regarding {sup 222}Rn exposure. The following sections describe the main projects in some detail.

  1. Temporal patterns and source apportionment of nitrate-nitrogen leaching in a paddy field at Kelantan, Malaysia.

    PubMed

    Hussain, Hazilia; Yusoff, Mohd Kamil; Ramli, Mohd Firuz; Abd Latif, Puziah; Juahir, Hafizan; Zawawi, Mohamed Azwan Mohammed

    2013-11-15

    Nitrate-nitrogen leaching from agricultural areas is a major cause for groundwater pollution. Polluted groundwater with high levels of nitrate is hazardous and cause adverse health effects. Human consumption of water with elevated levels of NO3-N has been linked to the infant disorder methemoglobinemia and also to non-Hodgkin's disease lymphoma in adults. This research aims to study the temporal patterns and source apportionment of nitrate-nitrogen leaching in a paddy soil at Ladang Merdeka Ismail Mulong in Kelantan, Malaysia. The complex data matrix (128 x 16) of nitrate-nitrogen parameters was subjected to multivariate analysis mainly Principal Component Analysis (PCA) and Discriminant Analysis (DA). PCA extracted four principal components from this data set which explained 86.4% of the total variance. The most important contributors were soil physical properties confirmed using Alyuda Forecaster software (R2 = 0.98). Discriminant analysis was used to evaluate the temporal variation in soil nitrate-nitrogen on leaching process. Discriminant analysis gave four parameters (hydraulic head, evapotranspiration, rainfall and temperature) contributing more than 98% correct assignments in temporal analysis. DA allowed reduction in dimensionality of the large data set which defines the four operating parameters most efficient and economical to be monitored for temporal variations. This knowledge is important so as to protect the precious groundwater from contamination with nitrate.

  2. Integrated Application of Multivariate Statistical Methods to Source Apportionment of Watercourses in the Liao River Basin, Northeast China.

    PubMed

    Chen, Jiabo; Li, Fayun; Fan, Zhiping; Wang, Yanjie

    2016-10-21

    Source apportionment of river water pollution is critical in water resource management and aquatic conservation. Comprehensive application of various GIS-based multivariate statistical methods was performed to analyze datasets (2009-2011) on water quality in the Liao River system (China). Cluster analysis (CA) classified the 12 months of the year into three groups (May-October, February-April and November-January) and the 66 sampling sites into three groups (groups A, B and C) based on similarities in water quality characteristics. Discriminant analysis (DA) determined that temperature, dissolved oxygen (DO), pH, chemical oxygen demand (CODMn), 5-day biochemical oxygen demand (BOD₅), NH₄⁺-N, total phosphorus (TP) and volatile phenols were significant variables affecting temporal variations, with 81.2% correct assignments. Principal component analysis (PCA) and positive matrix factorization (PMF) identified eight potential pollution factors for each part of the data structure, explaining more than 61% of the total variance. Oxygen-consuming organics from cropland and woodland runoff were the main latent pollution factor for group A. For group B, the main pollutants were oxygen-consuming organics, oil, nutrients and fecal matter. For group C, the evaluated pollutants primarily included oxygen-consuming organics, oil and toxic organics.

  3. Developing receptor-oriented methods for non-methane hydrocarbon characterisation in urban air. Part II: source apportionment

    NASA Astrophysics Data System (ADS)

    Borbon, Agnès; Fontaine, Hervé; Locoge, Nadine; Veillerot, Marc; Galloo, J. C.

    The methods and the results of non-methane hydrocarbon (NMHC) source apportionment are described at urban scale on a spatial and temporal basis. Here, hourly ambient concentrations of nearly 40 C 2-C 9 NMHC are used. Methods are based on the knowledge of the wintertime NMHC vehicle-exhaust emission ratio generally determined by simple regression analysis taking acetylene, ethylene, propene and 1,3-butadiene as auto-exhaust tracers. The RSD of the estimated source contributions is lower than 20%; the developed receptor-oriented methods are flexible and easily transposable to other areas. In winter, vehicle-exhaust emissions explain 100% of the NMHC majority levels and even isoprene. From May to November, our models revealed the temperature-dependent contribution of additional sources (0.71< r<0.90). On the one hand, the evaporation of fuel and solvent affects the whole C 4-C 9 NMHC fraction, and fluctuates between 20% and 50%, even for a northern France urban area. On the other hand, both vehicle-exhaust and biogenic emissions control the highly photoreactive isoprene distribution whatever the site; the traffic is responsible for a third of its levels in summer. Finally, the particular behaviour of the C 2-C 4 compounds pointed out dominant contributions, generally other than traffic. Suspected sources are numerous: natural gas leakage for ethane and propane, wintertime fuel evaporation for butanes and butenes, non-automotive combustion for ethylene and acetylene. Ethane and propane also showed that long-range advective transport, responsible for background concentrations, could significantly contribute to the hydrocarbon levels with a high atmospheric residence time (from 20% to 50%).

  4. Measurement, time series analysis and source apportionment of inorganic and organic speciated PM(2.5) air pollution in Denver

    NASA Astrophysics Data System (ADS)

    Dutton, Steven James

    Particulate air pollution has demonstrated significant health effects ranging from worsening of asthma to increased rates of respiratory and cardiopulmonary mortality. These results have prompted the US-EPA to include particulate matter (PM) as one of the six criteria air pollutants regulated under the Clean Air Act. The diverse chemical make-up and physical characteristics of PM make it a challenging pollutant to characterize and regulate. Particulate matter less than 2.5 microns in diameter (PM2.5) has the ability to travel deep into the lungs and therefore has been linked with some of the more significant health effects. The toxicity of any given particle is likely dependent on its chemical composition. The goal of this project has been to chemically characterize a long time series of PM 2.5 measurements collected at a receptor site in Denver to a level of detail that has not been done before on this size data set. This has involved characterization of inorganic ions using ion chromatography, total elemental and organic carbon using thermal optical transmission, and organic molecular marker species using gas chromatography-mass spectrometry. Methods have been developed to allow for daily measurement and speciation for these compounds over a six year period. Measurement methods, novel approaches to uncertainty estimation, time series analysis, spectral and pattern analyses and source apportionment using two multivariate factor analysis models are presented. Analysis results reveal several natural and anthropogenic sources contributing to PM2.5 in Denver. The most distinguishable sources are motor vehicles and biomass combustion. This information will be used in a health effect analysis as part of a larger study called the Denver Aerosol Sources and Health (DASH) study. Such results will inform regulatory decisions and may help create a better understanding of the underlying mechanisms for the observed adverse health effects associated with PM2.5.

  5. Application of 14C analyses to source apportionment of carbonaceous PM 2.5 in the UK

    NASA Astrophysics Data System (ADS)

    Heal, Mathew R.; Naysmith, Philip; Cook, Gordon T.; Xu, Sheng; Duran, Teresa Raventós; Harrison, Roy M.

    2011-05-01

    Determination of the radiocarbon ( 14C) content of airborne particulate matter yields insight into the proportion of the carbonaceous material derived from fossil and contemporary carbon sources. Daily samples of PM 2.5 were collected by high-volume sampler at an urban background site in Birmingham, UK, and the fraction of 14C in both the total carbon, and in the organic and elemental carbon fractions, determined by two-stage combustion to CO 2, graphitisation and quantification by accelerator mass spectrometry. OC and EC content was also determined by Sunset Analyzer. The mean fraction contemporary TC in the PM 2.5 samples was 0.50 (range 0.27-0.66, n = 26). There was no seasonality to the data, but there was a positive trend between fraction contemporary TC and magnitude of SOC/TC ratio and for the high values of these two parameters to be associated with air-mass back trajectories arriving in Birmingham from over land. Using a five-compartment mass balance model on fraction contemporary carbon in OC and EC, the following average source apportionment for the TC in these PM 2.5 samples was derived: 27% fossil EC; 20% fossil OC; 2% biomass EC; 10% biomass OC; and 41% biogenic OC. The latter category will comprise, in addition to BVOC-derived SOC, other non-combustion contemporary carbon sources such as biological particles, vegetative detritus, humic material and tyre wear. The proportion of total PM 2.5 at this location estimated to derive from BVOC-derived secondary organic aerosol was 9-29%. The findings from this work are consistent with those from elsewhere in Europe and support the conclusion of a significant and ubiquitous contribution from non-fossil biogenic sources to the carbon in terrestrial aerosol.

  6. Physically constrained source apportionment (PCSA) for polycyclic aromatic hydrocarbon using the Multilinear Engine 2-species ratios (ME2-SR) method.

    PubMed

    Liu, Gui-Rong; Shi, Guo-Liang; Tian, Ying-Ze; Wang, Yi-Nan; Zhang, Cai-Yan; Feng, Yin-Chang

    2015-01-01

    An improved physically constrained source apportionment (PCSA) technology using the Multilinear Engine 2-species ratios (ME2-SR) method was proposed and applied to quantify the sources of PM10- and PM2.5-associated polycyclic aromatic hydrocarbons (PAHs) from Chengdu in winter time. Sixteen priority PAH compounds were detected with mean ΣPAH concentrations (sum of 16 PAHs) ranging from 70.65 ng/m(3) to 209.58 ng/m(3) and from 59.17 ng/m(3) to 170.64 ng/m(3) for the PM10 and PM2.5 samples, respectively. The ME2-SR and positive matrix factorization (PMF) models were employed to estimate the source contributions of PAHs, and these estimates agreed with the experimental results. For the PMF model, the highest contributor to the ΣPAHs was vehicular emission (81.69% for PM10, 82.06% for PM2.5), followed by coal combustion (12.68%, 12.11%), wood combustion (5.65%, 4.45%) and oil combustion (0.72%, 0.88%). For the ME2-SR method, the highest contributions were from diesel (43.19% for PM10, 47.17% for PM2.5) and gasoline exhaust (34.94%, 32.44%), followed by wood combustion (8.79%, 6.37%), coal combustion (12.46%, 12.37%) and oil combustion (0.80%, 1.22%). However, the PAH ratios calculated for the factors extracted by ME2-SR were closer to the values from actual source profiles, implying that the results obtained from ME2-SR might be physically constrained and satisfactory.

  7. Estimation of organic carbon blank values and error structures of the speciation trends network data for source apportionment

    SciTech Connect

    Eugene Kim; Philip K. Hopke; Youjun Qin

    2005-08-01

    Because the particulate organic carbon (OC) concentrations reported in U.S. Environment Protection Agency Speciation Trends Network (STN) data were not blank corrected, the OC blank concentrations were estimated using the intercept in particulate matter {lt} 2.5 {mu}m in aerodynamic diameter (PM2.5) regression against OC concentrations. The estimated OC blank concentrations ranged from 1 to 2.4 {mu}g/m{sup 3} showing higher values in urban areas for the 13 monitoring sites in the northeastern United States. In the STN data, several different samplers and analyzers are used, and various instruments show different method detection limit (MDL) values, as well as errors. A comprehensive set of error structures that would be used for numerous source apportionment studies of STN data was estimated by comparing a limited set of measured concentrations and their associated uncertainties. To examine the estimated error structures and investigate the appropriate MDL values, PM2.5 samples collected at a STN site in Burlington, VT, were analyzed through the application of the positive matrix factorization. A total of 323 samples that were collected between December 2000 and December 2003 and 49 species based on several variable selection criteria were used, and eight sources were successfully identified in this study with the estimated error structures and min values among different MDL values from the five instruments: secondary sulfate aerosol (41%) identified as the result of emissions from coal-fired power plants, secondary nitrate aerosol (20%), airborne soil (15%), gasoline vehicle emissions (7%), diesel emissions (7%), aged sea salt (4%), copper smelting (3%), and ferrous smelting (2%). Time series plots of contributions from airborne soil indicate that the highly elevated impacts from this source were likely caused primarily by dust storms.

  8. Chemical characterization of PM1.0 aerosol in Delhi and source apportionment using positive matrix factorization.

    PubMed

    Jaiprakash; Singhai, Amrita; Habib, Gazala; Raman, Ramya Sunder; Gupta, Tarun

    2017-01-01

    Fine aerosol fraction (particulate matter with aerodynamic diameter <= 1.0 μm (PM)1.0) over the Indian Institute of Technology Delhi campus was monitored day and night (10 h each) at 30 m height from November 2009 to March 2010. The samples were analyzed for 5 ions (NH4(+), NO3(-), SO4(2-), F(-), and Cl(-)) and 12 trace elements (Na, K, Mg, Ca, Pb, Zn, Fe, Mn, Cu, Cd, Cr, and Ni). Importantly, secondary aerosol (sulfate and nitrate) formation was observed during dense foggy events, supporting the fog-smog-fog cycle. A total of 76 samples were used for source apportionment of PM mass. Six factors were resolved by PMF analyses and were identified as secondary aerosol, secondary chloride, biomass burning, soil dust, iron-rich source, and vehicular emission. The geographical location of the sources and/or preferred transport pathways was identified by conditional probability function (for local sources) and potential source contribution function (for regional sources) analyses. Medium- and small-scale metal processing (e.g. steel sheet rolling) industries in Haryana and National Capital Region (NCR) Delhi, coke and petroleum refining in Punjab, and thermal power plants in Pakistan, Punjab, and NCR Delhi were likely contributors to secondary sulfate, nitrate, and secondary chloride at the receptor site. The agricultural residue burning after harvesting season (Sept-Dec and Feb-Apr) in Punjab, and Haryana contributed to potassium at receptor site during November-December and March 2010. The soil dust from North and East Pakistan, and Rajasthan, North-East Punjab, and Haryana along with the local dust contributed to soil dust at the receptor site, during February and March 2010. A combination of temporal behavior and air parcel trajectory ensemble analyses indicated that the iron-rich source was most likely a local source attributed to emissions from metal processing facilities. Further, as expected, the vehicular emissions source did not show any seasonality and was

  9. Source apportionment of elevated BaP concentrations in PM10 aerosols in an alpine valley in Austria

    NASA Astrophysics Data System (ADS)

    Bauer, Heidi; Puxbaum, Hans; Jankowski, Nicole; Sampaio Cordeiro Wagner, Lylian

    2010-05-01

    INTRODUCTION: In a village situated at 1215 m a.s.l. in a natural preserve in an Austrian alpine valley elevated BaP concentrations have been measured in the last years. A highly frequented highway leading from Italy to Germany passes near the village. Monthly means of particulate BaP concentrations show a clear seasonal trend with values below 1 ng/m³ during the warmer months and with concentrations up to 9 ng/m³ in the cold season. Annual averages in the years 2000 - 2005 ranged between 1.4 and 2.8 ng/m³ - much higher than the EU target value of 1 ng/m³. We used a macrotracer model developed at the Vienna University of Technology to determine the contributions of the sources for BaP emissions, which were mainly space heating with wood and traffic from the highway. EXPERIMENTAL: The macrotracer concept is a nine component model to derive source contribution and explains 80-100% of PM10 aerosols in Austria. The amount of traffic exhaust is derived by using EC as tracer, whereas EC produced by wood burning is subtracted, the amount of wood smoke is derived by the anhydro-sugar levoglucosan and the ratio between the anhydro-sugars levoglucosan and mannosan. For the source apportionment of BaP the applied factors reflect on the one hand the composition of the automotive fleet in Austria and on the other hand the composition of the fire wood in the region. Filter samples collected with a high volume sampler in winter were analyzed for PM10 aerosol mass, total, organic, elemental and carbonate carbon, HULIS, anhydro-sugars, polyols and ions (major ions and organic acids) and PAHs. In the same way emission samples taken at a motor test stand and at a test stand for wood combustion were analyzed (Schmidl et al. 2008). The saccharides were determined using high pH anion exchange and pulsed amperometry (HPAE-PAD). Details of the analytical method are given in Iinuma et al., 2009. Elemental and organic carbon were determined with a thermal-optical instrument (Sunset lab

  10. Receptor modeling of source apportionment of Hong Kong aerosols and the implication of urban and regional contribution

    NASA Astrophysics Data System (ADS)

    Guo, H.; Ding, A. J.; So, K. L.; Ayoko, G.; Li, Y. S.; Hung, W. T.

    Understanding the spatial-temporal variations of source apportionment of PM 2.5 is critical to the effective control of particulate pollution. In this study, two one-year studies of PM 2.5 composition were conducted at three contrasting sites in Hong Kong from November 2000 to October 2001, and from November 2004 to October 2005, respectively. A receptor model, principal component analysis (PCA) with absolute principal component scores (APCS) technique, was applied to the PM 2.5 data for the identification and quantification of pollution sources at the rural, urban and roadside sites. The receptor modeling results identified that the major sources of PM 2.5 in Hong Kong were vehicular emissions/road erosion, secondary sulfate, residual oil combustion, soil suspension and sea salt regardless of sampling sites and sampling periods. The secondary sulfate aerosols made the most significant contribution to the PM 2.5 composition at the rural (HT) (44 ± 3%, mean ± 1 σ standard error) and urban (TW) (28 ± 2%) sites, followed by vehicular emission (20 ± 3% for HT and 23 ± 4% for TW) and residual oil combustion (17 ± 2% for HT and 19 ± 1% for TW). However, at the roadside site (MK), vehicular emissions especially diesel vehicle emissions were the major source of PM 2.5 composition (33 ± 1% for diesel vehicle plus 18 ± 2% for other vehicles), followed by secondary sulfate aerosols (24 ± 1%). We found that the contribution of residual oil combustion at both urban and rural sites was much higher than that at the roadside site (2 ± 0.4%), perhaps due to the marine vessel activities of the container terminal near the urban site and close distance of pathway for the marine vessels to the rural site. The large contribution of secondary sulfate aerosols at all the three sites reflected the wide influence of regional pollution. With regard to the temporal trend, the contributions of vehicular emission and secondary sulfate to PM 2.5 showed higher autumn and winter values

  11. Influence of organic and inorganic markers in the source apportionment of airborne PM10 in Zaragoza (Spain) by two receptor models.

    PubMed

    Callén, M S; López, J M; Mastral, A M

    2013-05-01

    Improving knowledge on the apportionment of airborne particulate matter will be useful to handle and fulfill the legislation regarding this pollutant. The main aim of this work was to assess the influence of markers in the source apportionment of airborne PM10, in particular, whether the use of particle polycyclic aromatic hydrocarbon (PAH) and ions provided similar results to the ones obtained using not only the mentioned markers but also gas phase PAH and trace elements. In order to reach this aim, two receptor models: UNMIX and positive matrix factorization were applied to two sets of data in Zaragoza city from airborne PM10, a previously reported campaign (2003-2004) (Callén et al. Chemosphere 76:1120-1129, 2009), where PAH associated to the gas and particle phases, ions and trace elements were used as markers and a long sampling campaign (2001-2009), where only PAH in the particle phase and ions were analyzed. For both campaigns, positive matrix factorization was able to explain a higher number of sources than the UNMIX model. Independently of the sampling campaign and the receptor model used, soil resuspension was the main PM10 source, especially in the warm period (21st March-21st September), where most of the PM10 exceedances were produced. Despite some of the markers of anthropogenic sources were different for both campaigns, common sources associated to different combustion sources (coal, light-oil, heavier-oil, biomass, and traffic) were found and PAH in particle phase and ions seemed to be good markers for the airborne PM10 apportionment.

  12. StreamVOC--A Deterministic Source-Apportionment Model to Estimate Volatile Organic Compound Concentrations in Rivers and Streams

    USGS Publications Warehouse

    Asher, William E.; Bender, David A.; Zogorski, John S.; Bartholomay, Roy C.

    2006-01-01

    This report documents the construction and verification of the model, StreamVOC, that estimates (1) the time- and position-dependent concentrations of volatile organic compounds (VOCs) in rivers and streams as well as (2) the source apportionment (SA) of those concentrations. The model considers how different types of sources and loss processes can act together to yield a given observed VOC concentration. Reasons for interest in the relative and absolute contributions of different sources to contaminant concentrations include the need to apportion: (1) the origins for an observed contamination, and (2) the associated human and ecosystem risks. For VOCs, sources of interest include the atmosphere (by absorption), as well as point and nonpoint inflows of VOC-containing water. Loss processes of interest include volatilization to the atmosphere, degradation, and outflows of VOC-containing water from the stream to local ground water. This report presents the details of StreamVOC and compares model output with measured concentrations for eight VOCs found in the Aberjona River at Winchester, Massachusetts. Input data for the model were obtained during a synoptic study of the stream system conducted July 11-13, 2001, as part of the National Water-Quality Assessment (NAWQA) Program of the U.S. Geological Survey. The input data included a variety of basic stream characteristics (for example, flows, temperature, and VOC concentrations). The StreamVOC concentration results agreed moderately well with the measured concentration data for several VOCs and provided compound-dependent SA estimates as a function of longitudinal distance down the river. For many VOCs, the quality of the agreement between the model-simulated and measured concentrations could be improved by simple adjustments of the model input parameters. In general, this study illustrated: (1) the considerable difficulty of quantifying correctly the locations and magnitudes of ground-water-related sources of

  13. New insight into the spatiotemporal variability and source apportionments of C1-C4 alkyl nitrates in Hong Kong

    NASA Astrophysics Data System (ADS)

    Ling, Zhenhao; Guo, Hai; Simpson, Isobel Jane; Saunders, Sandra Maria; Lam, Sean Ho Man; Lyu, Xiaopu; Blake, Donald Ray

    2016-07-01

    C1-C4 alkyl nitrates (RONO2) were measured concurrently at a mountain site, Tai Mo Shan (TMS), and an urban site, Tsuen Wan (TW), at the base of the same mountain in Hong Kong from September to November 2010. Although the levels of parent hydrocarbons were much lower at TMS (p < 0.05), similar alkyl nitrate levels were found at both sites regardless of the elevation difference, suggesting various source contributions of alkyl nitrates at the two sites. Prior to using a positive matrix factorization (PMF) model, the data at TW were divided into "meso" and "non-meso" scenarios for the investigation of source apportionments with the influence of mesoscale circulation and regional transport, respectively. Secondary formation was the prominent contributor of alkyl nitrates in the meso scenario (60 ± 2 %, 60.2 ± 1.2 pptv), followed by biomass burning and oceanic emissions, while biomass burning and secondary formation made comparable contributions to alkyl nitrates in the non-meso scenario, highlighting the strong emissions of biomass burning in the inland Pearl River delta (PRD) region. In contrast to TW, the alkyl nitrate levels measured at TMS mainly resulted from the photooxidation of the parent hydrocarbons at TW during mesoscale circulation, i.e., valley breezes, corresponding to 52-86 % of the alkyl nitrate levels at TMS. Furthermore, regional transport from the inland PRD region made significant contributions to the levels of alkyl nitrates (˜ 58-82 %) at TMS in the non-meso scenario, resulting in similar levels of alkyl nitrates observed at the two sites. The simulation of secondary formation pathways using a photochemical box model found that the reaction of alkyl peroxy radicals (RO2) with nitric oxide (NO) dominated the formation of RONO2 at both sites, and the formation of alkyl nitrates contributed negatively to O3 production, with average reduction rates of 4.1 and 4.7 pptv pptv-1 at TMS and TW, respectively.

  14. Diurnal variations and source apportionment of ozone at the summit of Mount Huang, a rural site in Eastern China.

    PubMed

    Gao, J; Zhu, B; Xiao, H; Kang, H; Hou, X; Yin, Y; Zhang, L; Miao, Q

    2017-03-01

    Comprehensive measurements were conducted at the summit of Mount (Mt.) Huang, a rural site located in eastern China during the summer of 2011. They observed that ozone showed pronounced diurnal variations with high concentrations at night and low values during daytime. The Weather Research and Forecasting with Chemistry (WRF-Chem) model was applied to simulate the ozone concentrations at Mt. Huang in June 2011. With processes analysis and online ozone tagging method we coupled into the model system, the causes of this diurnal pattern and the contributions from different source regions were investigated. Our results showed that boundary layer diurnal cycle played an important role in driving the ozone diurnal variation. Further analysis showed that the negative contribution of vertical mixing was significant, resulting in the ozone decrease during the daytime. In contrast, ozone increased at night owing to the significant positive contribution of advection. This shifting of major factor between vertical mixing and advection formed this diurnal variation. Ozone source apportionment results indicated that approximately half was provided by inflow effect of ozone from outside the model domain (O3-INFLOW) and the other half was formed by ozone precursors (O3-PBL) emitted in eastern, central, and southern China. In the O3-PBL, 3.0% of the ozone was from Mt. Huang reflecting the small local contribution (O3-LOC) and the non-local contributions (O3-NLOC) accounted for 41.6%, in which ozone from the southerly regions contributed significantly, for example, 9.9% of the ozone originating from Jiangxi, representing the highest geographical contributor. Because the origin and variation of O3-NLOC was highly related to the diurnal movements in boundary layer, the similar diurnal patterns between O3-NLOC and total ozone both indicated the direct influence of O3-NLOC and the importance of boundary layer diurnal variations in the formation of such distinct diurnal ozone variations

  15. Source apportionment of indoor, outdoor and personal PM2.5 exposure of pregnant women in Barcelona, Spain

    NASA Astrophysics Data System (ADS)

    Minguillón, M. C.; Schembari, A.; Triguero-Mas, M.; de Nazelle, A.; Dadvand, P.; Figueras, F.; Salvado, J. A.; Grimalt, J. O.; Nieuwenhuijsen, M.; Querol, X.

    2012-11-01

    Exposure to air pollution has been shown to adversely affect foetal development in the case of pregnant women. The present study aims to investigate the PM composition and sources influencing personal exposure of pregnant women in Barcelona. To this end, indoor, outdoor and personal exposure measurements were carried out for a selection of 54 pregnant women between November 2008 and November 2009. PM2.5 samples were collected during two consecutive days and then analysed for black smoke (BS), major and trace elements, and polycyclic aromatic hydrocarbons (PAHs) concentrations. Personal information such as commuting patterns and cosmetics use was also collected. PM2.5 concentrations were higher for personal samples than for indoor and outdoor environments. Indoor, outdoor and personal BS and sulphate concentrations were strongly correlated, although some specific indoor and outdoor sulphate sources may exist. Average trace elements concentrations were similar indoor, outdoor and for personal exposure, but the correlations were moderate for most of them. Most of the PAHs concentrations showed strong correlations indoor-outdoor. A source apportionment analysis of the PM composition data by means of a Positive Matrix Factorization (PMF) resulted in the identification of six sources for the outdoor and indoor environments: secondary sulphate, fueloil + sea salt (characterized by V, Ni, Na and Mg), mineral, cigarette (characterized by K, Ce, Cd, benzo(k)fluoranthene and benzo(ghi)perylene), road traffic (characterized by BS and low weight PAHs), and industrial (characterized by Pb, Sn, Cu, Mn and Fe). For personal exposure two specific sources were found: cosmetics (characterized by abundance of Ca, Li, Ti and Sr and the absence of Al) and train/subway (characterized by Fe, Mn, Cu and Ba). The contribution of the sources varied widely among women, especially for cigarette (from zero to up to 4 μg m-3), train/subway (up to more than 6 μg m-3) and cosmetics (up to more

  16. Fine particulate matter (PM2.5) in Edmonton, Canada: Source apportionment and potential risk for human health.

    PubMed

    Bari, Md Aynul; Kindzierski, Warren B

    2016-11-01

    To design effective PM2.5 control strategies in urban centers, there is a need to better understand local and remote sources influencing PM2.5 levels and associated risk to public health. An investigation of PM2.5 levels, sources and potential human health risk associated with trace elements in the PM2.5 was undertaken in Edmonton over a 6-year period (September 2009-August 2015). The geometric mean PM2.5 concentration of was 7.11 μg/m(3) (interquartile range, IQR = 4.83-10.08 μg/m(3)). Positive matrix factorization (PMF) receptor modeling identified secondary organic aerosol (SOA) as the major contributor (2.2 μg/m(3), 27%), followed by secondary nitrate (1.3 μg/m(3), 17%) and secondary sulfate (1.2 μg/m(3), 15%). Other local sources included transportation (1.1 μg/m(3), 14%) and industry-related emissions (0.26 μg/m(3), 3.4%), biomass burning (1.0 μg/m(3), 13%) and soil (0.54 μg/m(3), 6.8%). Five factors (i.e., SOA, secondary nitrate, secondary sulfate, transportation and biomass burning) contributed more than 85% to PM2.5 for the 2009-2015 period. Geometric (arithmetic) mean and maximum ambient air concentrations for hazardous trace elements of public health concern in PM2.5 during the study period were below United States regulatory agency chronic and acute health risk screening criteria. Carcinogenic and non-carcinogenic risk of trace elements and source-specific risk values were well below acceptable and safe levels of risks recommended by regulatory agencies. More work is needed to understand the origin of potential SOA and wintertime wood burning sources in Edmonton and the surrounding region and to apply source-risk apportionment using all available hazardous air pollutants (HAPs) including organic compounds to better interpret the potential health risk posed by various sources in urban areas.

  17. Source apportionment and organic compound characterization of ambient ultrafine particulate matter (PM) in the Los Angeles Basin

    NASA Astrophysics Data System (ADS)

    Hasheminassab, Sina; Daher, Nancy; Schauer, James J.; Sioutas, Constantinos

    2013-11-01

    .8% of PM0.25 on an annual average basis over all sites. Comparison of our results to PM2.5 OC apportionment, conducted at central LA, shows that contribution of mobile sources to PM0.25 OC is more than two times higher than PM2.5 (75% and 30%, respectively), while “other OC” contributed significantly higher to PM2.5 OC compared to PM0.25 (56% and 21%, respectively).

  18. Monitoring and source apportionment of trace elements in PM2.5: Implications for local air quality management.

    PubMed

    Li, Yueyan; Chang, Miao; Ding, Shanshan; Wang, Shiwen; Ni, Dun; Hu, Hongtao

    2017-03-08

    Fine particulate matter (PM2.5) samples were collected simultaneously every hour in Beijing between April 2014 and April 2015 at five sites. Thirteen trace elements (TEs) in PM2.5 were analyzed by online X-ray fluorescence (XRF). The annual average PM2.5 concentrations ranged from 76.8 to 102.7 μg m(-3). TEs accounted for 5.9%-8.7% of the total PM2.5 mass with Cl, S, K, and Si as the most dominant elements. Spearman correlation coefficients of PM2.5 or TE concentrations between the background site and other sites showed that PM2.5 and some element loadings were affected by regional and local sources, whereas Cr, Si, and Ni were attributed to substantial local emissions. Temporal variations of TEs in PM2.5 were significant and provided information on source profiles. The PM2.5 concentrations were highest in autumn and lowest in summer. Mn and Cr showed similar variation. Fe, Ca, Si, and Ti tended to show higher concentrations in spring, whereas concentrations of S peaked in summer. Concentrations of Cl, K, Pb, Zn, Cu, and Ni peaked in winter. PM2.5 and TE median concentrations were higher on Saturdays than on weekdays. The diurnal pattern of PM2.5 and TE median concentrations yielded similar bimodal patterns. Five dominant sources of PM2.5 mass were identified via positive matrix factorization (PMF). These sources included the regional and local secondary aerosols, traffic, coal burning, soil dust, and metal processing. Air quality management strategies, including regional environmental coordination and collaboration, reduction in secondary aerosol precursors, restrictive vehicle emission standards, promotion of public transport, and adoption of clean energy, should be strictly implemented. High time-resolution measurements of TEs provided detailed source profiles, which can greatly improve precision in interpreting source apportionment calculations; the PMF analysis of online XRF data is a powerful tool for local air quality management.

  19. Bioavailability of Polycyclic Aromatic Hydrocarbons and their Potential Application in Eco-risk Assessment and Source Apportionment in Urban River Sediment

    PubMed Central

    Yang, Xunan; Yu, Liuqian; Chen, Zefang; Xu, Meiying

    2016-01-01

    Traditional risk assessment and source apportionment of sediments based on bulk polycyclic aromatic hydrocarbons (PAHs) can introduce biases due to unknown aging effects in various sediments. We used a mild solvent (hydroxypropyl-β-cyclodextrin) to extract the bioavailable fraction of PAHs (a-PAHs) from sediment samples collected in Pearl River, southern China. We investigated the potential application of this technique for ecological risk assessments and source apportionment. We found that the distribution of PAHs was associated with human activities and that the a-PAHs accounted for a wide range (4.7%–21.2%) of total-PAHs (t-PAHs), and high risk sites were associated with lower t-PAHs but higher a-PAHs. The correlation between a-PAHs and the sediment toxicity assessed using tubificid worms (r = −0.654, P = 0.021) was greater than that from t-PAH-based risk assessment (r = −0.230, P = 0.472). Moreover, the insignificant correlation between a-PAH content and mPEC-Q of low molecular weight PAHs implied the potiential bias of t-PAH-based risk assessment. The source apportionment from mild extracted fractions was consistent across different indicators and was in accordance with typical pollution sources. Our results suggested that mild extraction-based approaches reduce the potential error from aging effects because the mild extracted PAHs provide a more direct indicator of bioavailability and fresher fractions in sediments. PMID:26976450

  20. Source apportionment of PM2.5 at a regional background site in North China using PMF linked with radiocarbon analysis: insight into the contribution of biomass burning

    NASA Astrophysics Data System (ADS)

    Zong, Zheng; Wang, Xiaoping; Tian, Chongguo; Chen, Yingjun; Qu, Lin; Ji, Ling; Zhi, Guorui; Li, Jun; Zhang, Gan

    2016-09-01

    Source apportionment of fine particles (PM2.5) at a background site in North China in the winter of 2014 was done using statistical analysis, radiocarbon (14C) measurement and positive matrix factorization (PMF) modeling. Results showed that the concentration of PM2.5 was 77.6 ± 59.3 µg m-3, of which sulfate (SO42-) concentration was the highest, followed by nitrate (NO3-), organic carbon (OC), elemental carbon (EC) and ammonium (NH4+). As demonstrated by backward trajectory, more than half of the air masses during the sampling period were from the Beijing-Tianjin-Hebei (BTH) region, followed by Mongolia and the Shandong Peninsula. Cluster analysis of chemical species suggested an obvious signal of biomass burning in the PM2.5 from the Shandong Peninsula, while the PM2.5 from the BTH region showed a vehicle emission pattern. This finding was further confirmed by the 14C measurement of OC and EC in two merged samples. The 14C result indicated that biogenic and biomass burning emission contributed 59 ± 4 and 52 ± 2 % to OC and EC concentrations, respectively, when air masses originated from the Shandong Peninsula, while the contributions fell to 46 ± 4 and 38 ± 1 %, respectively, when the prevailing wind changed and came from the BTH region. The minimum deviation between source apportionment results from PMF and 14C measurement was adopted as the optimal choice of the model exercises. Here, two minor overestimates with the same range (3 %) implied that the PMF result provided a reasonable source apportionment of the regional PM2.5 in this study. Based on the PMF modeling, eight sources were identified; of these, coal combustion, biomass burning and vehicle emission were the main contributors of PM2.5, accounting for 29.6, 19.3 and 15.9 %, respectively. Compared with overall source apportionment, the contributions of vehicle emission, mineral dust, coal combustion and biomass burning increased when air masses came from the BTH region, Mongolia and the Shandong

  1. SOURCE APPORTIONMENT OF PHOENIX PM2.5 AEROSOL WITH THE UNMIX RECEPTOR MODEL

    EPA Science Inventory

    The multivariate receptor model Unmix has been used to analyze a 3-yr PM2.5 ambient aerosol data set collected in Phoenix, AZ, beginning in 1995. The analysis generated source profiles and overall percentage source contribution estimates (SCE) for five source categories: ga...

  2. Sources of methane and nitrous oxide in California's Central Valley estimated through direct airborne flux and positive matrix factorization source apportionment of groundbased and regional tall tower measurements

    NASA Astrophysics Data System (ADS)

    Guha, Abhinav

    -San Joaquin River Delta in the Central Valley. Through analysis of these field measurements, this dissertation presents the apportionment of observed CH4 and N2O concentration enhancements into major source categories along with direct emissions estimates from airborne observations. We perform high-precision measurements of greenhouse gases using gas analyzers based on absorption spectroscopy, and other source marker volatile organic compounds (VOCs) using state of the art VOC measurement systems (e.g. proton transfer reaction mass spectrometry). We combine these measurements with a statistical source apportionment technique called positive matrix factorization (PMF) to evaluate and investigate the major local sources of CH4 and N2O during CalNex and Walnut Grove campaigns. In the CABERNET study, we combine measurements with an airborne approach to a well-established micrometeorological technique (eddy-covariance method) to derive CH4 fluxes over different source regions in the Central Valley. In the CalNex experiments, we demonstrate that dairy and livestock remains the largest source sector of non-CO2 greenhouse gases in the San Joaquin Valley contributing most of the CH4 and much of the measured N2O at Bakersfield. Agriculture is observed to provide another major source of N2O, while vehicle emissions are found to be an insignificant source of N2O, contrary to the current statewide greenhouse gas inventory which includes vehicles as a major source. Our PMF source apportionment also produces an evaporative/fugitive factor but its relative lack of CH4 contributions points to removal processes from vented emissions in the surrounding O&G industry and the overwhelming dominance of the dairy CH4 source. In the CABERNET experiments, we report enhancements of CH4 from a number of sources spread across the spatial domain of the Central Valley that improves our understanding of their distribution and relative strengths. We observe large enhancements of CH4 mixing ratios over the

  3. Vertical profile, contamination assessment, and source apportionment of heavy metals in sediment cores of Kaohsiung Harbor, Taiwan.

    PubMed

    Chen, Chih-Feng; Ju, Yun-Ru; Chen, Chiu-Wen; Dong, Cheng-Di

    2016-12-01

    Six sediment cores collected at the Kaohsiung Harbor of Taiwan were analyzed to evaluate their vertical profiles, enrichments, accumulations, and source apportionments of heavy metals. This was performed to investigate any potential ecological risks posed by heavy metals. Results indicated that the mean heavy metal content (mg kg(-1)) in the six sediment cores was as follows: Hg (0.4-6.4), Cd (<0.05-2.4), Cr (18-820), Cu (16-760), Pb (31-140), and Zn (76-1900). The patterns of heavy metal content in the sediment cores differed substantially among the four river mouths. However, the vertical profiles of metals were relatively stable, indicating that wastewater has the constant characteristics and has been discharged into the rivers for a long period of time. Results of pollution assessment of enrichment factor, geo-accumulation index, and pollution load index revealed that river mouths experience severe enrichment, strong accumulation, and high contamination from the primary heavy metals. It was not consistent in the assessment results of mean effect range median quotient, potential ecological risk index, and total toxic unit method. Potential ecological risks caused by Hg in the sediments at Canon River and Love River mouths on aquatic organisms were extremely high. The estimates derived from the receptor modeling of multiple linear regression of the absolute principal component scores indicated that the contributions of the composite heavy metals derived from the Canon River and the Love River on the potential toxicity and risks to the water environment of Kaohsiung Harbor were highest, followed by those derived from Salt River and Jen-Gen River.

  4. Multiple-year black carbon measurements and source apportionment using delta-C in Rochester, New York.

    PubMed

    Wang, Yungang; Hopke, Philip K; Rattigan, Oliver V; Chalupa, David C; Utell, Mark J

    2012-08-01

    Black carbon (BC), an important component ofthe atmospheric aerosol, has climatic, environmental, and human health significance. In this study, BC was continuously measured using a two-wavelength aethalometer (370 nm and 880 nm) in Rochester; New York, from January 2007 to December 2010. The monitoring site is adjacent to two major urban highways (I-490 and I-590), where 14% to 21% of the total traffic was heavy-duty diesel vehicles. The annual average BC concentrations were 0.76 microg/m3, 0.67 microg/m3, 0.60 microg/m3, and 0.52 microg/m3 in 2007, 2008, 2009, and 2010, respectively. Positive matrix factorization (PMF) modeling was performed using PM2.5 elements, sulfate, nitrate, ammonia, elemental carbon (EC), and organic carbon (OC) data from the US. Environmental Protection Agency (EPA) speciation network and Delta-C (UVBC370nm-BC880nm) data. Delta-C has been previously shown to be a tracer of wood combustion factor It was used as an input variable in source apportionment models for the first time in this study and was found to play an important role in separating traffic (especially diesel) emissions from wood combustion emissions. The result showed the annual average PM2.5 concentrations apportioned to diesel emissions in 2007, 2008, 2009, and 2010 were 1.34 microg/m3, 1.25 microg/m3, 1.13 microg/m3, and 0.97 microg/m3, respectively. The BC conditional probability function (CPF) plots show a large contribution from the highway diesel traffic to elevated BC concentrations. The measurements and modeling results suggest an impact of the US Environmental Protection Agency (EPA) 2007 Heavy-Duty Highway Rule on the decrease ofBC and PM2.5 concentrations during the study period.

  5. Source apportionment of ambient non-methane hydrocarbons in Hong Kong: application of a principal component analysis/absolute principal component scores (PCA/APCS) receptor model.

    PubMed

    Guo, H; Wang, T; Louie, P K K

    2004-06-01

    Receptor-oriented source apportionment models are often used to identify sources of ambient air pollutants and to estimate source contributions to air pollutant concentrations. In this study, a PCA/APCS model was applied to the data on non-methane hydrocarbons (NMHCs) measured from January to December 2001 at two sampling sites: Tsuen Wan (TW) and Central & Western (CW) Toxic Air Pollutants Monitoring Stations in Hong Kong. This multivariate method enables the identification of major air pollution sources along with the quantitative apportionment of each source to pollutant species. The PCA analysis identified four major pollution sources at TW site and five major sources at CW site. The extracted pollution sources included vehicular internal engine combustion with unburned fuel emissions, use of solvent particularly paints, liquefied petroleum gas (LPG) or natural gas leakage, and industrial, commercial and domestic sources such as solvents, decoration, fuel combustion, chemical factories and power plants. The results of APCS receptor model indicated that 39% and 48% of the total NMHCs mass concentrations measured at CW and TW were originated from vehicle emissions, respectively. 32% and 36.4% of the total NMHCs were emitted from the use of solvent and 11% and 19.4% were apportioned to the LPG or natural gas leakage, respectively. 5.2% and 9% of the total NMHCs mass concentrations were attributed to other industrial, commercial and domestic sources, respectively. It was also found that vehicle emissions and LPG or natural gas leakage were the main sources of C(3)-C(5) alkanes and C(3)-C(5) alkenes while aromatics were predominantly released from paints. Comparison of source contributions to ambient NMHCs at the two sites indicated that the contribution of LPG or natural gas at CW site was almost twice that at TW site. High correlation coefficients (R(2) > 0.8) between the measured and predicted values suggested that the PCA/APCS model was applicable for estimation

  6. Mass closure and source apportionment of PM2.5 by Positive Matrix Factorization analysis in urban Mediterranean environment

    NASA Astrophysics Data System (ADS)

    Mantas, E.; Remoundaki, E.; Halari, I.; Kassomenos, P.; Theodosi, C.; Hatzikioseyian, A.; Mihalopoulos, N.

    2014-09-01

    A systematic monitoring of PM2.5 was carried out during a period of three years (from February 2010 to April 2013) at an urban site, at the National Technical University of Athens campus. Two types of 24-h PM2.5 samples have been collected: 271 samples on PTFE and 116 samples on quartz filters. Daily PM2.5 concentrations were determined for both types of samples. Total sulfur, crustal origin elements and elements of a major crustal component (Al, Si, Fe, Ca, K, Mg, Ti) trace elements (Zn, Pb, Cu, Ni, P, V, Cr, Mn) and water soluble ions (Cl-, NO3-, SO42-, Na+, K+, NH4+, Ca2+, Mg2+) were determined on the PTFE samples. Organic carbon (OC), elemental carbon (EC) and water soluble ions were determined on the quartz samples. For the mass closure six components were considered: Secondary Inorganic Aerosol (SIA), Organic Matter (OM), Elemental Carbon (EC), Dust, Mineral anthropogenic component (MIN) and Sea Salt (SS). SIA and OM contributed in the mass of PM2.5 almost equally: 30-36% and 30% respectively. EC, SS and MIN accounted for 5, 4 and 3% respectively of the total PM2.5 mass. Dust accounted for about 3-5% in absence of dust transport event and reached a much higher percentage in case of dust transport event. These contributions justify at least 80% of the PM2.5 mass. Source apportionment analysis has been performed by Positive Matrix Factorization. The combination of the PMF results obtained by both data sets lead to the definition of six factors: 1. SO42-, NH4+, OC (industrial/regional sources, secondary aerosol) 2. EC, OC, K and trace metals (traffic and heating by biomass burning, locally emitted aerosol). 3. Ca, EC, OC and trace metals (urban-resuspended road dust reflecting exhaust emissions), 4. Secondary nitrates 5. Na, Cl (marine source) 6. Si, Al, Ti, Ca, Fe (Dust transported from Sahara). These factors reflect not only main sources contributions but also underline the key role of atmospheric dynamics and aerosol ageing processes in this Mediterranean

  7. Chemical Composition and Source Apportionment of Size Fractionated Particulate Matter in Cleveland, Ohio, USA

    EPA Science Inventory

    The Cleveland airshed comprises a complex mixture of industrial source emissions that contribute to periods of non-attainment for fine particulate matter (PM 2.5 ) and are associated with increased adverse health outcomes in the exposed population. Specific PM sources responsible...

  8. Source apportionment and pollution evaluation of heavy metals in water and sediments of Buriganga River, Bangladesh, using multivariate analysis and pollution evaluation indices.

    PubMed

    Bhuiyan, Mohammad Amir Hossain; Dampare, Samuel B; Islam, M A; Suzuki, Shigeyuki

    2015-01-01

    Concentrations of heavy metals in water and sediment samples of Buriganga River in the capital city Dhaka, Bangladesh, were studied to understand the level of heavy metals and their source apportionment. The results showed that the mean concentrations of heavy metals both in water and sediment samples were very high and, in most cases, exceeded the permissible limits recommended by the Bangladesh government and other international organizations. Significantly higher concentrations of Pb, Cr, Mn, Co, Ni, Cu, Zn, As, and Cd were found in sediment samples. However, average concentrations of metals both in water and sediment samples were above the effect range median. The heavy metal pollution index (HPI) and degree of contamination (Cd) yielded different results in water samples despite significant correlations between them. The heavy metal evaluation index (HEI) showed strong correlations with HPI and Cd and provided better assessment of pollution levels. The enrichment factor (EF) and geoaccumulation index (Igeo) showed the elevated value of Cr, Pb, and Cd in access of background values. The measured elements were subjected to positive matrix factorization (PMF) and examining correlations in order to explain the content, behavior, and source apportionment of metals. PMF resulted in a successful partitioning of variances into sources related to background geochemistry and contaminant influences. However, the PMF approach successfully demarcated the major sources of metals from tannery, paint, municipal sewage, textiles, and agricultural activities.

  9. Source apportionment of air pollution exposures of rural Chinese women cooking with biomass fuels

    NASA Astrophysics Data System (ADS)

    Huang, Wei; Baumgartner, Jill; Zhang, Yuanxun; Wang, Yuqin; Schauer, James J.

    2015-03-01

    Particulate matter (PM) from different sources may differentially affect human health. Few studies have assessed the main sources of personal exposure to PM and their contributions among residents of developing countries, where pollution sources differ from those in higher-income settings. 116 daily (24-h) personal PM2.5 exposure samples were collected among 81 women cooking with biomass fuels in two villages in rural Yunnan, China. The PM samples were analyzed for mass and chemical composition, including water-soluble organic carbon (WSOC), black carbon (BC), and molecular markers. We found black carbon, n-alkanes and levoglucosan dominated the most abundant fractions of the total measured species and average personal PM2.5 exposure was higher in winter than that in summer in both villages. The composition data were then analyzed using a positive matrix factorization (PMF) receptor model to identify the main PM emission sources contributing to women's exposures and to assess their spatial (between villages) and seasonal variation in our study setting. The 6-factor solution provided reasonably stable profiles and was selected for further analysis. Our results show that rural Chinese women cooking with biomass fuels are exposed to a variety of sources. The identified factors include wood combustion (41.1%), a cooking source (35.6%), a mobile source (12.6%), plant waxes (6.7%), pyrolysis combustion (3.0%), and secondary organic aerosols (SOA; 1.0%). The mean source contributions of the mobile source, cooking source, and wood combustion factor to PM2.5 exposure were significantly different between women living in the two study villages, whereas the mean SOA, wood combustion, and plant waxes factors differed seasonally. There was no relationship between source contributions and questionnaire-based measurements of source-specific exposures, implying that the impacts of source contributions on exposure are affected by complex spatial, temporal and behavioral patterns

  10. Spatial variation and source apportionment of water pollution in Qiantang River (China) using statistical techniques.

    PubMed

    Huang, Fang; Wang, Xiaoquan; Lou, Liping; Zhou, Zhiqing; Wu, Jiaping

    2010-03-01

    Understanding the spatial distribution and apportioning the sources of water pollution are important in the study and efficient management of water resources. In this work, we considered data for 13 water quality variables collected during the year 2004 at 46 monitoring sites along the Qiantang River (China). Fuzzy comprehensive analysis categorized the data into three major pollution zones (low, moderate, and high) based on national quality standards for surface waters, China. Most sites classified as "low pollution zones" (LP) occurred in the main river channel, whereas those classified as "moderate and high pollution zones" (MP and HP, respectively) occurred in the tributaries. Factor analysis identified two potential pollution sources that explained 67% of the total variance in LP, two potential pollution sources that explained 73% of the total variance in MP, and three potential pollution sources that explained 80% of the total variance in HP. UNMIX was used to estimate contributions from identified pollution sources to each water quality variable and each monitoring site. Most water quality variables were influenced primarily by pollution due to industrial wastewater, agricultural activities and urban runoff. In LP, non-point source pollution such as agricultural runoff and urban runoff dominated; in MP and HP, mixed source pollution dominated. The pollution in the small tributaries was more serious than that in the main channel. These results provide information for developing better pollution control strategies for the Qiantang River.

  11. Aerosol species concentrations and source apportionment of ammonia at Rocky Mountain National Park.

    PubMed

    Malm, William C; Schichtel, Bret A; Barna, Michael G; Gebhart, Kristi A; Rodriguez, Marco A; Collett, Jeffrey L; Carrico, Christian M; Benedict, Katherine B; Prenni, Anthony J; Kreidenweis, Sonia M

    2013-11-01

    Changes in ecosystem function at Rocky Mountain National Park (RMNP) are occurring because of emissions of nitrogen and sulfate species along the Front Range of the Colorado Rocky Mountains, as well as sources farther east and west. The nitrogen compounds include both oxidized and reduced nitrogen. A year-long monitoring program of various oxidized and reduced nitrogen species was initiated to better understand their origins as well as the complex chemistry occurring during transport from source to receptor. Specifically the goals of the study were to characterize the atmospheric concentrations of nitrogen species in gaseous, particulate, and aqueous phases (precipitation and clouds) along the east and west sides of the Continental Divide; identify the relative contributions to atmospheric nitrogen species in RMNP from within and outside of the state of Colorado; identify the relative contributions to atmospheric nitrogen species in RMNP from emission sources along the Colorado Front Range versus other areas within Colorado; and identify the relative contributions to atmospheric nitrogen species from mobile sources, agricultural activities, and large and small point sources within the state of Colorado. Measured ammonia concentrations are combined with modeled releases of conservative tracers from ammonia source regions around the United States to apportion ammonia to its respective sources, using receptor modeling tools.

  12. Source apportionment of chlorinated polycyclic aromatic hydrocarbons associated with ambient particles in a Japanese megacity

    PubMed Central

    Kamiya, Yuta; Iijima, Akihiro; Ikemori, Fumikazu; Okuda, Tomoaki; Ohura, Takeshi

    2016-01-01

    Chlorinated polycyclic aromatic hydrocarbons (ClPAHs) are novel species of environmental contaminants whose possible sources remain unclear. The occurrence of ClPAHs within total suspended particles (TSP) is compared with weekly air samples at two sites of differing characteristics (industrial and residential) in the megacity of Nagoya, Japan. Samples were collected over 12 months during 2011–2012. All 24 species of targeted ClPAHs were detected at both industrial and residential sites, where mean concentrations of total ClPAHs in TSP were 20.7 and 14.1 pg/m3, respectively. High concentrations at the industrial site were frequently observed during winter, suggesting potent seasonal ClPAH sources there. Positive matrix factorization modeling of particulate ClPAH source identification and apportioning were conducted for datasets including ClPAHs, PAHs, elements and ions, plus elemental carbons in TSP. Eight factors were identified as possible ClPAH sources, with estimates that the dominant one was a specific source of ClPAH emission (31%), followed by traffic (23%), photodegradable and semi-volatile species (18%), long-range transport (11%), and industry and oil combustion (10%). Source contributions of ClPAHs differed substantially from those of PAHs. This suggests specific and/or potent ClPAH sources in the local area, and that the production mechanisms between ClPAHs and PAHs are substantially different. PMID:27922081

  13. Source apportionment of chlorinated polycyclic aromatic hydrocarbons associated with ambient particles in a Japanese megacity

    NASA Astrophysics Data System (ADS)

    Kamiya, Yuta; Iijima, Akihiro; Ikemori, Fumikazu; Okuda, Tomoaki; Ohura, Takeshi

    2016-12-01

    Chlorinated polycyclic aromatic hydrocarbons (ClPAHs) are novel species of environmental contaminants whose possible sources remain unclear. The occurrence of ClPAHs within total suspended particles (TSP) is compared with weekly air samples at two sites of differing characteristics (industrial and residential) in the megacity of Nagoya, Japan. Samples were collected over 12 months during 2011–2012. All 24 species of targeted ClPAHs were detected at both industrial and residential sites, where mean concentrations of total ClPAHs in TSP were 20.7 and 14.1 pg/m3, respectively. High concentrations at the industrial site were frequently observed during winter, suggesting potent seasonal ClPAH sources there. Positive matrix factorization modeling of particulate ClPAH source identification and apportioning were conducted for datasets including ClPAHs, PAHs, elements and ions, plus elemental carbons in TSP. Eight factors were identified as possible ClPAH sources, with estimates that the dominant one was a specific source of ClPAH emission (31%), followed by traffic (23%), photodegradable and semi-volatile species (18%), long-range transport (11%), and industry and oil combustion (10%). Source contributions of ClPAHs differed substantially from those of PAHs. This suggests specific and/or potent ClPAH sources in the local area, and that the production mechanisms between ClPAHs and PAHs are substantially different.

  14. Source apportionment of single particles sampled at the industrially polluted town of Port Talbot, United Kingdom by ATOFMS

    NASA Astrophysics Data System (ADS)

    Taiwo, Adewale M.; Harrison, Roy M.; Beddows, David C. S.; Shi, Zongbo

    2014-11-01

    Single particle analysis of an industrially polluted atmosphere in Port Talbot, South Wales, United Kingdom was conducted using Aerosol-Time-of-Flight Mass Spectrometry (ATOFMS). During the four week sampling campaign, a total of 5,162,018 particles were sized in the size range 0.2-1.9 μm aerodynamic diameter. Of these, 580,798 were successfully ionized generating mass spectra. K-means clustering employed for analysing ATOFMS data utilized 96% of the hit particles to generate 20 clusters. Similar clusters were merged together and 17 clusters were generated from which 7 main particle groups were identified. The particle classes include: K-rich particles (K-CN, K-NO3, K-EC, K-Cl-PO3 and K-HSO4), aged sea salt (Na-NO3), silicate dust (Na-HSiO2), sulphate rich particles (K-HSO4), nitrate rich particles (AlO-NO3), Ca particles (Ca-NO3), carbon-rich particles (Mn-OC, Metallic-EC, EC, EC-NO3 and OC-EC), and aromatic hydrocarbon particles (Arom-CN, Fe-PAH-NO3 and PAH-CN). With the aid of wind sector plots, the K-Cl-PO3 and Na-HSiO2 particle clusters were related to the steelworks blast furnace/sinter plant while Ca-rich particles arose from blast furnace emissions. K-CN, K-EC, Na-HSiO2, K-HSO4, Mn-OC, Arom-CN, Fe-PAH-NO3, and PAH-CN particles were closely linked with emissions from the cokemaking and mills (hot and cold) steelworks sections. The source factors identified by the ATOFMS were compared with those derived from multivariate analysis using Multilinear Engine (ME-2) applied to filter samples analysed off-line. Both methods of source apportionment identified common source factors including those within the steelworks (blast furnace, sinter, cokemaking), as well as marine, traffic and secondary particles, but quantitative attribution of mass is very different.

  15. An inter-comparison of PM2.5 at urban and urban background sites: Chemical characterization and source apportionment

    NASA Astrophysics Data System (ADS)

    Cesari, D.; Donateo, A.; Conte, M.; Merico, E.; Giangreco, A.; Giangreco, F.; Contini, D.

    2016-06-01

    A measurement campaign was performed between 04/03/2013 and 17/07/2013 for simultaneous collection of PM2.5 samples in two nearby sites in southeastern Italy: an urban site and an urban background site. PM2.5 at the two sites were similar; however, the chemical composition and the contributions of the main sources were significantly different. The coefficients of divergence (CODs) showed spatial heterogeneity of EC (higher at the urban site because of traffic emissions) and of all metals. Major ions (NH4+, Na+, and SO42 -) and OC had low CODs, suggesting a homogeneous distribution of sea spray, secondary sulfate, and secondary organic matter (SOM = 1.6*OCsec, where OCsec is the secondary OC). The strong correlations between Na+ and Cl-, and the low Cl-/Na+ ratios, suggested the presence of aged sea spray with chloride depletion (about 79% of Cl-) and formation of sodium nitrate at both sites. In both sites, the non-sea-salt sulfate was about 97% of sulfate, and the strong correlation between SO42 - and NH4+ indicated that ammonium was present as ammonium sulfate. However, during advection of Saharan Dust, calcium sulfate was present rather than ammonium sulfate. The source apportionment was performed using the Positive Matrix Factorization comparing outputs of model EPA PMF 3.0 and 5.0 version. Six aerosol sources were identified at both sites: traffic, biomass burning, crustal-resuspended dust, secondary nitrate, marine aerosol, and secondary sulfate. The PMF3.0 model was not completely able, in these sites, to separate marine contribution from secondary nitrate and secondary sulfate from OC, underestimating the marine contribution and overestimating the secondary sulfate with respect to stoichiometric calculations. The application of specific constraints on PMF5.0 provided cleaner profiles, improving the comparison with stoichiometric calculations. The seasonal trends revealed larger biomass burning contributions during the cold period at both sites due to

  16. Study on source apportionment of Non-Methane Hydrocarbon Compounds (NMHC) in Dagang Oil Field

    SciTech Connect

    Zhu Tan; Lin Tao; Bai Zhipeng

    1996-12-31

    To identify the sources of non-methane total hydrocarbon in atmosphere in the region of Dagang Oil Field, 35 samples were collected and 10 hydrocarbon compounds were analyzed with GC/FID. Then, the Chemical Mass Balance Receptor Model was set up and the source contributions and standard errors were determined with the effective variance weighted least squares estimation method. The sources of the non-methane total hydrocarbon in this region includes crude oil, gasoline, natural gas, liquefied petroleum gas and motor exhaust, whose contributions are 46.64%, 8.56%, 20.05%, 18.17% and 6.08% respectively. Upon these analyses, the major sources of regional non-methane total hydrocarbon are crude oil, natural gas and liquefied petroleum gas.

  17. Chemical characterization and source apportionment of fine and coarse particulate matter in Lahore, Pakistan

    NASA Astrophysics Data System (ADS)

    Stone, Elizabeth; Schauer, James; Quraishi, Tauseef A.; Mahmood, Abid

    2010-03-01

    Lahore, Pakistan is an emerging megacity that is heavily polluted with high levels of particle air pollution. In this study, respirable particulate matter (PM 2.5 and PM 10) were collected every sixth day in Lahore from 12 January 2007 to 19 January 2008. Ambient aerosol was characterized using well-established chemical methods for mass, organic carbon (OC), elemental carbon (EC), ionic species (sulfate, nitrate, chloride, ammonium, sodium, calcium, and potassium), and organic species. The annual average concentration (±one standard deviation) of PM 2.5 was 194 ± 94 μg m -3 and PM 10 was 336 ± 135 μg m -3. Coarse aerosol (PM 10-2.5) was dominated by crustal sources like dust (74 ± 16%, annual average ± one standard deviation), whereas fine particles were dominated by carbonaceous aerosol (organic matter and elemental carbon, 61 ± 17%). Organic tracer species were used to identify sources of PM 2.5 OC and chemical mass balance (CMB) modeling was used to estimate relative source contributions. On an annual basis, non-catalyzed motor vehicles accounted for more than half of primary OC (53 ± 19%). Lesser sources included biomass burning (10 ± 5%) and the combined source of diesel engines and residual fuel oil combustion (6 ± 2%). Secondary organic aerosol (SOA) was an important contributor to ambient OC, particularly during the winter when secondary processing of aerosol species during fog episodes was expected. Coal combustion alone contributed a small percentage of organic aerosol (1.9 ± 0.3%), but showed strong linear correlation with unidentified sources of OC that contributed more significantly (27 ± 16%). Brick kilns, where coal and other low quality fuels are burned together, are suggested as the most probable origins of unapportioned OC. The chemical profiling of emissions from brick kilns and other sources unique to Lahore would contribute to a better understanding of OC sources in this megacity.

  18. Source apportionment of PM10 mass and particulate carbon in the Kathmandu Valley, Nepal

    NASA Astrophysics Data System (ADS)

    Kim, Bong Mann; Park, Jin-Soo; Kim, Sang-Woo; Kim, Hyunjae; Jeon, Haeun; Cho, Chaeyoon; Kim, Ji-Hyoung; Hong, Seungkyu; Rupakheti, Maheswar; Panday, Arnico K.; Park, Rokjin J.; Hong, Jihyung; Yoon, Soon-Chang

    2015-12-01

    The Kathmandu Valley in Nepal is a bowl-shaped urban basin in the Himalayan foothills with a serious problem of fine particulate air pollution that impacts local health and impairs visibility. Particulate carbon concentrations have reached severe levels that threaten the health of 3.5 million local residents. Moreover, snow and ice on the Himalayan mountains are melting as a result of additional warming due to particulate carbon, especially high black carbon concentrations. To date, the sources of the Valley's particulate carbon and the impacts of different sources on particulate carbon concentrations are not well understood. Thus, before an effective control strategy can be developed, these particulate carbon sources must be identified and quantified. Our study has found that the four primary sources of particulate carbon in the Kathmandu Valley during winter are brick kilns, motor vehicles, fugitive soil dust, and biomass/garbage burning. Their source contributions are quantified using a recently developed new multivariate receptor model SMP. In contrast to other highly polluted areas such as China, secondary contribution is almost negligible in Kathmandu Valley. Brick kilns (40%), motor vehicles (37%) and biomass/garbage burning (22%) have been identified as the major sources of elemental carbon (black carbon) in the Kathmandu Valley during winter, while motor vehicles (47%), biomass/garbage burning (32%), and soil dust (13%) have been identified as the most important sources of organic carbon. Our research indicates that controlling emissions from motor vehicles, brick kilns, biomass/garbage burning, and soil dust is essential for the mitigation of the particulate carbon that threatens public health, impairs visibility, and influences climate warming within and downwind from the Kathmandu Valley. In addition, this paper suggests several useful particulate carbon mitigation methods that can be applied to Kathmandu Valley and other areas in South Asia with

  19. PM10 source apportionment in a Swiss Alpine valley impacted by highway traffic.

    PubMed

    Ducret-Stich, Regina E; Tsai, Ming-Yi; Thimmaiah, Devraj; Künzli, Nino; Hopke, Philip K; Phuleria, Harish C

    2013-09-01

    Although trans-Alpine highway traffic exhaust is one of the major sources of air pollution along the highway valleys of the Alpine regions, little is known about its contribution to residential exposure and impact on respiratory health. In this paper, source-specific contributions to particulate matter with an aerodynamic diameter < 10 μm (PM10) and their spatio-temporal distribution were determined for later use in a pediatric asthma panel study in an Alpine village. PM10 sources were identified by positive matrix factorization using chemical trace elements, elemental, and organic carbon from daily PM10 filters collected between November 2007 and June 2009 at seven locations within the village. Of the nine sources identified, four were directly road traffic-related: traffic exhaust, road dust, tire and brake wear, and road salt contributing 16 %, 8 %, 1 %, and 2 % to annual PM10 concentrations, respectively. They showed a clear dependence with distance to highway. Additional contributions were identified from secondary particles (27 %), biomass burning (18 %), railway (11 %), and mineral dust including a local construction site (13 %). Comparing these source contributions with known source-specific biomarkers (e.g., levoglucosan, nitro-polycyclic aromatic hydrocarbons) showed high agreement with biomass burning, moderate with secondary particles (in winter), and lowest agreement with traffic exhaust.

  20. Source apportionment of wet-deposited atmospheric mercury in Tampa, Florida

    NASA Astrophysics Data System (ADS)

    Michael, Ryan; Stuart, Amy L.; Trotz, Maya A.; Akiwumi, Fenda

    2016-03-01

    In this paper, sources of mercury deposition to the Tampa area (Florida, USA) are investigated by analysis of one year (March 2000-March 2001) of daily wet deposition data. HYSPLIT back-trajectory modeling was performed to assess potential source locations for high versus low concentration events in data stratified by precipitation level. Positive matrix factorization (PMF) was also applied to apportion the elemental compositions from each event and to identify sources. Increased total mercury deposition was observed during summer months, corresponding to increased precipitation. However, mercury concentration in deposited samples was not strongly correlated with precipitation amount. Back-trajectories show air masses passing over Florida land in the short (12 h) and medium (24 h) term prior to deposition for high mercury concentration events. PMF results indicate that eleven factors contribute to the deposited elements in the event data. Diagnosed elemental profiles suggest the sources that contribute to mercury wet deposition at the study site are coal combustion (52% of the deposited mercury mass), municipal waste incineration (23%), medical waste incineration (19%), and crustal dust (6%). Overall, results suggest that sources local to the county and in Florida likely contributed substantially to mercury deposition at the study site, but distant sources may also contribute.

  1. Seasonal trends, chemical speciation and source apportionment of fine PM in Tehran

    NASA Astrophysics Data System (ADS)

    Arhami, Mohammad; Hosseini, Vahid; Zare Shahne, Maryam; Bigdeli, Mostafa; Lai, Alexandra; Schauer, James J.

    2017-03-01

    Frequent air pollution episodes have been reported for Tehran, Iran, mainly because of critically high levels of fine particulate matter (PM2.5). The composition and sources of these particles are poorly known, so this study aims to identify the major components and heavy metals in PM2.5 along with their seasonal trends and associated sources. 24-hour PM2.5 samples were collected at a main residential station every 6 days for a full year from February 2014 to February 2015. The samples were analyzed for ions, organic carbon (including water-soluble and insoluble portions), elemental carbon (EC), and all detectable elements. The dominant mass components, which were determined by means of chemical mass closure, were organic matter (35%), dust (25%), non-sea salt sulfate (11%), EC (9%), ammonium (5%), and nitrate (2%). Organic matter and EC together comprised 44% of fine PM on average (increased to >70% in the colder season), which reflects the significance of anthropogenic urban sources (i.e. vehicles). The contributions of different components varied considerably throughout the year, particularly the dust component that varied from 7% in the cold season to 56% in the hot and dry season. Principal component analyses were applied, resulting in 5 major source factors that explained 85% of the variance in fine PM. Factor 1, representing soil dust, explained 53%; Factor 2 denotes heavy metals mainly found in industrial sources and accounted for 18%; and rest of factors, mainly representing combustion sources, explained 14% of the variation. The levels of major heavy metals were further evaluated, and their trends showed considerable increases during cold seasons. The results of this study provide useful insight to fine PM in Tehran, which could help in identifying their health effects and sources, and also adopting effective control strategies.

  2. Source Apportionment of Volatile Organic Compounds in an Urban Environment at the Yangtze River Delta, China.

    PubMed

    An, Junlin; Wang, Junxiu; Zhang, Yuxin; Zhu, Bin

    2017-04-01

    Volatile organic compounds (VOCs) were collected continuously during June-August 2013 and December 2013-February 2014 at an urban site in Nanjing in the Yangtze River Delta. The positive matrix factorization receptor model was used to analyse the sources of VOCs in different seasons. Eight and seven sources were identified in summer and winter, respectively. In summer and winter, the dominant sources of VOCs were vehicular emissions, liquefied petroleum gas/natural gas (LPG/NG) usage, solvent usage, biomass/biofuel burning, and industrial production. In summer, vehicular emissions made the most significant contribution to ambient VOCs (38%), followed by LPG/NG usage (20%), solvent usage (19%), biomass/biofuel burning (13%), and industrial production (10%). In winter, LPG/NG usage accounted for 36% of ambient VOCs, whereas vehicular emissions, biomass/biofuel burning, industrial production and solvent usage contributed 30, 18, 9, and 6%, respectively. The contribution of LPG/NG usage in winter was approximately four times that in summer, whereas the contribution from biomass/biofuel burning in winter was more than twice that in summer. The sources related to vehicular emissions and LPG/NG usages were important. Using conditional probability function analysis, the VOC sources were mainly associated with easterly, northeasterly and southeasterly directions, pointing towards the major expressway and industrial area. Using the propylene-equivalent method, paint and varnish (23%) was the highest source of VOCs in summer and biomass/biofuel burning (36%) in winter. Using the ozone formation potential method, the most important source was biomass/biofuel burning (32% in summer and 47% in winter). The result suggests that the biomass/biofuel burning and paint and varnish play important roles in controlling ozone chemical formation in Nanjing.

  3. Source apportionment of PAHs using Unmix model for Yantai costal surface sediments, China.

    PubMed

    Lang, Yin-Hai; Yang, Wei

    2014-01-01

    16 Polycyclic aromatic hydrocarbons (PAHs) in 20 surface sediments from Yantai offshore area were measured. The total PAHs concentrations varied from 450.0 to 4,299.0 ng/g, with a mean of 2,492.9 ng/g. The high molecular weight (HMW) PAHs were most abundant and the ratio ranged from 54.9 % to 81.6 % in all sampling stations, indicating that pyrogenic sources were a predominant contribution to PAHs pollution. The source contributions of PAHs were estimated based on the EPA Unmix 6.0 receptor model. The data were well simulated due to a high correlation coefficient between predicted and measured PAHs concentration (R(2) = 0.99). A mixed source of coal combustion and traffic pollution contributed to 38.9 % of the measured PAHs, followed by diesel emission (38.8 %) and a mixed source of biomass combustion and gasoline engine emissions (22.3 %). The current findings further validated that Unmix model could be applied to apportion the sources of PAHs in sediments.

  4. Source apportionment and health risk assessment of trace metals in surface soils of Beijing metropolitan, China.

    PubMed

    Chen, Haiyang; Teng, Yanguo; Lu, Sijin; Wang, Yeyao; Wu, Jin; Wang, Jinsheng

    2016-02-01

    Understanding the exposure risks of trace metals in contamination soils and apportioning their sources are the basic preconditions for soil pollution prevention and control. In this study, a detailed investigation was conducted to assess the health risks of trace metals in surface soils of Beijing which is one of the most populated cities in the world and to apportion their potential sources. The data set of metals for 12 elements in 240 soil samples was collected. Pollution index and enrichment factor were used to identify the general contamination characteristic of soil metals. The probabilistic risk model was employed for health risk assessment, and a chemometrics technique, multivariate curve resolution-weighted alternating least squares (MCR-WALS), was applied to apportion sources. Results suggested that the soils in Beijing metropolitan region were contaminated by Hg, Cd, Cu, As, and Pb in varying degree, lying in the moderate pollution level. As a whole, the health risks posed by soil metals were acceptable or close to tolerable. Comparatively speaking, children and adult females were the relatively vulnerable populations for the non-carcinogenic and carcinogenic risks, respectively. Atmospheric deposition, fertilizers and agrochemicals, and natural source were apportioned as the potential sources determining the contents of trace metals in soils of Beijing area with contributions of 15.5%-16.4%, 5.9%-7.7% and 76.0%-78.6%, respectively.

  5. Apportionment of urban aerosol sources in Cork (Ireland) by synergistic measurement techniques.

    PubMed

    Dall'Osto, Manuel; Hellebust, Stig; Healy, Robert M; O'Connor, Ian P; Kourtchev, Ivan; Sodeau, John R; Ovadnevaite, Jurgita; Ceburnis, Darius; O'Dowd, Colin D; Wenger, John C

    2014-09-15

    The sources of ambient fine particulate matter (PM2.5) during wintertime at a background urban location in Cork city (Ireland) have been determined. Aerosol chemical analyses were performed by multiple techniques including on-line high resolution aerosol time-of-flight mass spectrometry (Aerodyne HR-ToF-AMS), on-line single particle aerosol time-of-flight mass spectrometry (TSI ATOFMS), on-line elemental carbon-organic carbon analysis (Sunset_EC-OC), and off-line gas chromatography/mass spectrometry and ion chromatography analysis of filter samples collected at 6-h resolution. Positive matrix factorization (PMF) has been carried out to better elucidate aerosol sources not clearly identified when analyzing results from individual aerosol techniques on their own. Two datasets have been considered: on-line measurements averaged over 2-h periods, and both on-line and off-line measurements averaged over 6-h periods. Five aerosol sources were identified by PMF in both datasets, with excellent agreement between the two solutions: (1) regional domestic solid fuel burning--"DSF_Regional," 24-27%; (2) local urban domestic solid fuel burning--"DSF_Urban," 22-23%; (3) road vehicle emissions--"Traffic," 15-20%; (4) secondary aerosols from regional anthropogenic sources--"SA_Regional" 9-13%; and (5) secondary aged/processed aerosols related to urban anthropogenic sources--"SA_Urban," 21-26%. The results indicate that, despite regulations for restricting the use of smoky fuels, solid fuel burning is the major source (46-50%) of PM2.5 in wintertime in Cork, and also likely other areas of Ireland. Whilst wood combustion is strongly associated with OC and EC, it was found that peat and coal combustion is linked mainly with OC and the aerosol from these latter sources appears to be more volatile than that produced by wood combustion. Ship emissions from the nearby port were found to be mixed with the SA_Regional factor. The PMF analysis allowed us to link the AMS cooking organic

  6. Comparison of lead isotopes with source apportionment models, including SOM, for air particulates.

    PubMed

    Gulson, Brian; Korsch, Michael; Dickson, Bruce; Cohen, David; Mizon, Karen; Davis, J Michael

    2007-08-01

    We have measured high precision lead isotopes in PM(2.5) particulates from a highly-trafficked site (Mascot) and rural site (Richmond) in the Sydney Basin, New South Wales, Australia to compare with isotopic data from total suspended particulates (TSP) from other sites in the Sydney Basin and evaluate relationships with source fingerprints obtained from multi-element PM(2.5) data. The isotopic data for the period 1998 to 2004 show seasonal peaks and troughs that are more pronounced in the rural site for the PM(2.5).samples but are consistent with the TSP. The Self Organising Map (SOM) method has been applied to the multi-element PM(2.5) data to evaluate its use in obtaining fingerprints for comparison with standard statistical procedures (ANSTO model). As seasonal effects are also significant for the multi-element data, the SOM modelling is reported as site and season dependent. At the Mascot site, the ANSTO model exhibits decreasing (206)Pb/(204)Pb ratios with increasing contributions of fingerprints for "secondary smoke" (industry), "soil", "smoke" and "seaspray". Similar patterns were shown by SOM winter fingerprints for both sites. At the rural site, there are large isotopic variations but for the majority of samples these are not associated with increased contributions from the main sources with the ANSTO model. For two winter sampling times, there are increased contributions from "secondary industry", "smoke", "soil" and seaspray with one time having a source or sources of Pb similar to that of Mascot. The only positive relationship between increasing (206)Pb/(204)Pb ratio and source contributions is found at the rural site using the SOM summer fingerprints, both of which show a significant contribution from sulphur. Several of the fingerprints using either model have significant contributions from black carbon (BC) and/or sulphur (S) that probably derive from diesel fuels and industrial sources. Increased contributions from sources with the SOM summer

  7. Modeling study of natural emissions, source apportionment, and emission control of atmospheric mercury

    NASA Astrophysics Data System (ADS)

    Shetty, Suraj K.

    Mercury (Hg) is a toxic pollutant and is important to understand its cycling in the environment. In this dissertation, a number of modeling investigations were conducted to better understand the emission from natural surfaces, the source-receptor relationship of the emissions, and emission reduction of atmospheric mercury. The first part of this work estimates mercury emissions from vegetation, soil and water surfaces using a number of natural emission processors and detailed (LAI) Leaf Area Index data from GIS (Geographic Information System) satellite products. East Asian domain was chosen as it contributes nearly 50% of the global anthropogenic mercury emissions into the atmosphere. The estimated annual natural mercury emissions (gaseous elemental mercury) in the domain are 834 Mg yr-1 with 462 Mg yr-1 contributing from China. Compared to anthropogenic sources, natural sources show greater seasonal variability (highest in simmer). The emissions are significant, sometimes dominant, contributors to total mercury emission in the regions. The estimates provide possible explanation for the gaps between the anthropogenic emission estimates based on activity data and the emission inferred from field observations in the regions. To understand the contribution of domestic emissions to mercury deposition in the United States, the second part of the work applies the mercury model of Community Multi-scale Air Quality Modeling system (CMAQ-Hg v4.6) to apportion the various emission sources attributing to the mercury wet and dry deposition in the 6 United States receptor regions. Contributions to mercury deposition from electric generating units (EGU), iron and steel industry (IRST), industrial point sources excluding EGU and IRST (OIPM), the remaining anthropogenic sources (RA), natural processes (NAT), and out-of-boundary transport (BC) in domain was estimated. The model results for 2005 compared reasonably well to field observations made by MDN (Mercury Deposition Network

  8. Chemical characterization of atmospheric particles and source apportionment in the vicinity of a steelmaking industry.

    PubMed

    Almeida, S M; Lage, J; Fernández, B; Garcia, S; Reis, M A; Chaves, P C

    2015-07-15

    The objective of this work was to provide a chemical characterization of atmospheric particles collected in the vicinity of a steelmaking industry and to identify the sources that affect PM10 levels. A total of 94 PM samples were collected in two sampling campaigns that occurred in February and June/July of 2011. PM2.5 and PM2.5-10 were analyzed for a total of 22 elements by Instrumental Neutron Activation Analysis and Particle Induced X-ray Emission. The concentrations of water soluble ions in PM10 were measured by Ion Chromatography and Indophenol-Blue Spectrophotometry. Positive Matrix Factorization receptor model was used to identify sources of particulate matter and to determine their mass contribution to PM10. Seven main groups of sources were identified: marine aerosol identified by Na and Cl (22%), steelmaking and sinter plant represented by As, Cr, Cu, Fe, Ni, Mn, Pb, Sb and Zn (11%), sinter plant stack identified by NH4(+), K and Pb (12%), an unidentified Br source (1.8%), secondary aerosol from coke making and blast furnace (19%), fugitive emissions from the handling of raw material, sinter plant and vehicles dust resuspension identified by Al, Ca, La, Si, Ti and V (14%) and sinter plant and blast furnace associated essentially with Fe and Mn (21%).

  9. Source Apportionment of the Summer Time Carbonaceous Aerosol at Nordic Rural Background Sites

    EPA Science Inventory

    In the present study, natural and anthropogenic sources of particulate organic carbon (OCp) and elemental carbon (EC) have been quantified based on weekly filter samples of PM10 (particles with aerodynamic diameter <10µ collected at four Nordic rural backgro...

  10. Chiral source apportionment of polychlorinated biphenyls to the Hudson River estuary atmosphere and food web.

    PubMed

    Asher, Brian J; Wong, Charles S; Rodenburg, Lisa A

    2007-09-01

    The New York/New Jersey Harbor Estuary is subject to significant contamination of polychlorinated biphenyls (PCBs) from numerous sources, including the historically contaminated Upper Hudson River, stormwater runoff and sewer overflows, and atmospheric deposition from PCBs originating from the surrounding urban area. However, the relative importance of these sources to the estuary's food web is not fully understood. Sources of PCBs to the estuary were apportioned using chiral signatures of PCBs in air, water, total suspended matter, phytoplankton, and sediment. PCBs 91, 95, 136, and 149 were racemic in the atmosphere of the estuary. However, the other phases contained nonracemic PCB 95 and to a lesser extent PCB 149. Thus, the predominant atmospheric source of these congeners is likely unweathered local pollution and not volatilization from the estuary. The similarity in chiral signatures in the other phases is consistent with dynamic contaminant exchange among them. Chiral signatures in the dissolved phase and total suspended matter were correlated with Upper Hudson discharge, suggesting thatthe delivery of nonracemic contaminated sediment from the Upper Hudson, not the atmosphere, controls phytoplankton uptake of some PCBs. Thus, measures to control PCB contamination in the Upper Hudson should be effective in reducing loadings to the estuary's aquatic ecosystem.

  11. Source apportionment of ambient fine particle size distribution using positive matrix factorization in Erfurt, Germany

    PubMed Central

    Yue, Wei; Stölzel, Matthias; Cyrys, Josef; Pitz, Mike; Heinrich, Joachim; Kreyling, Wolfgang G.; Wichmann, H.-Erich; Peters, Annette; Wang, Sheng; Hopke, Philip K.

    2008-01-01

    Particle size distribution data collected between September 1997 and August 2001 in Erfurt, Germany were used to investigate the sources of ambient particulate matter by positive matrix factorization (PMF). A total of 29,313 hourly averaged particle size distribution measurements covering the size range of 0.01 to 3.0 μm were included in the analysis. The particle number concentrations (cm−3) for the 9 channels in the ultrafine range, and mass concentrations (ng m−3) for the 41 size bins in the accumulation mode and particle up to 3 μm in aerodynamic diameter were used in the PMF. The analysis was performed separately for each season. Additional analyses were performed including calculations of the correlations of factor contributions with gaseous pollutants (O3, NO, NO2, CO and SO2) and particle composition data (sulfate, organic carbon and elemental carbon), estimating the contributions of each factor to the total number and mass concentration, identifying the directional locations of the sources using the conditional probability function, and examining the diurnal patterns of factor scores. These results were used to assist in the interpretation of the factors. Five factors representing particles from airborne soil, ultrafine particles from local traffic, secondary aerosols from local fuel combustion, particles from remote traffic sources, and secondary aerosols from multiple sources were identified in all seasons. PMID:18433834

  12. Source apportionment of fine organic aerosol in Mexico City during the MILAGRO Experiment 2006

    NASA Astrophysics Data System (ADS)

    Stone, E. A.; Snyder, D. C.; Sheesley, R. J.; Sullivan, A. P.; Weber, R. J.; Schauer, J. J.

    2007-07-01

    Organic carbon (OC) comprises a large fraction of fine particulate matter (PM2.5) in Mexico City. Daily and select 12-h PM2.5 samples were collected in urban and peripheral sites in Mexico City from 17-30 March 2006. Samples were analyzed for OC and elemental carbon (EC) using thermal-optical filter-based methods. Real-time water-soluble organic carbon (WSOC) was collected at the peripheral site. Organic compounds, particularly molecular markers, were quantified by soxhlet extraction with methanol and dichloromethane, derivitization, and gas chromatography with mass spectrometric detection (GCMS). A chemical mass balance model (CMB) based on molecular marker species was used to determine the relative contribution of major sources to ambient OC. Motor vehicles, including diesel and gasoline, consistently accounted for 47% of OC in the urban area and 31% on the periphery. The daily contribution of biomass burning to OC was highly variable, and ranged from 5-30% at the urban site and 11-50% at the peripheral site. The remaining OC unapportioned to primary sources showed a strong correlation with WSOC and was considered to be secondary in nature. Comparison of temporally resolved OC showed that contributions from primary aerosol sources during daylight hours were not significantly different from nighttime. This study provides quantitative understanding of the important sources of OC during the MILAGRO 2006 field campaign.

  13. Source apportionment of fine organic aerosol in Mexico City during the MILAGRO experiment 2006

    NASA Astrophysics Data System (ADS)

    Stone, E. A.; Snyder, D. C.; Sheesley, R. J.; Sullivan, A. P.; Weber, R. J.; Schauer, J. J.

    2008-03-01

    Organic carbon (OC) comprises a large fraction of fine particulate matter (PM2.5) in Mexico City. Daily and select 12-h PM2.5 samples were collected in urban and peripheral sites in Mexico City from 17-30 March 2006. Samples were analyzed for OC and elemental carbon (EC) using thermal-optical filter-based methods. Real-time water-soluble organic carbon (WSOC) was collected at the peripheral site. Organic compounds, particularly molecular markers, were quantified by soxhlet extraction with methanol and dichloromethane, derivitization, and gas chromatography with mass spectrometric detection (GCMS). A chemical mass balance model (CMB) based on molecular marker species was used to determine the relative contribution of major sources to ambient OC. Motor vehicles, including diesel and gasoline, consistently accounted for 49% of OC in the urban area and 32% on the periphery. The daily contribution of biomass burning to OC was highly variable, and ranged from 5-26% at the urban site and 7-39% at the peripheral site. The remaining OC unapportioned to primary sources showed a strong correlation with WSOC and was considered to be secondary in nature. Comparison of temporally resolved OC showed that contributions from primary aerosol sources during daylight hours were not significantly different from nighttime. This study provides quantitative understanding of the important sources of OC during the MILAGRO 2006 field campaign.

  14. SOURCE APPORTIONMENT OF PM2.5 AT AN URBAN IMPROVE SITE IN SEATTLE, WA

    EPA Science Inventory

    The multivariate receptor models Positive Matrix Factorization (PMF) and Unmix were used along with EPA's Chemical Mass Balance model to deduce the sources of PM2.5 at a centrally located urban site in Seattle, Washington. A total of 289 filter samples were obtained with an IM...

  15. Multi-source apportionment of polycyclic aromatic hydrocarbons using simultaneous linear equations

    NASA Astrophysics Data System (ADS)

    Marinaite, Irina; Semenov, Mikhail

    2014-05-01

    A new approach to identify multiple sources of polycyclic aromatic hydrocarbons (PAHs) and to evaluate the source contributions to atmospheric deposition of particulate PAHs is proposed. The approach is based on differences in concentrations of sums of PAHs with the same molecular weight among the sources. The data on PAHs accumulation in snow as well as the source profiles were used for calculations. Contributions of aluminum production plant, oil-fired central heating boilers, and residential wood and coal combustion were calculated using the linear mixing models. The concentrations of PAH pairs such as Benzo[b]fluorantene + Benzo[k]fluorantene and Benzo[g,h,i]perylene + Indeno[1,2,3-c,d]pyrene normalized to Benzo[a]antracene + Chrysene were used as tracers in mixing equations. The results obtained using ratios of sums of PAHs were compared with those obtained using molecular diagnostic ratios such as Benzo[a]antracene/Chrysene and Benzo[g,h,i]perylene/Indeno[1,2,3-c,d]pyrene. It was shown that the results obtained using diagnostic ratios as tracers are less reliable than results obtained using ratios of sums of PAHs. Funding was provided by Siberian Branch of Russian Academy of Sciences grant No. 8 (2012-2014).

  16. Seasonal changes, identification and source apportionment of PAH in PM1.0

    NASA Astrophysics Data System (ADS)

    Agudelo-Castañeda, Dayana Milena; Teixeira, Elba Calesso

    2014-10-01

    The objective of this research was to evaluate the seasonal variation of PAHs in PM1.0, as well as to identify and quantify the contributions of each source profile using the PMF receptor model. PM1.0 samples were collected on PTFE filters from August 2011 to July 2013 in the Metropolitan Area of Porto Alegre, Rio Grande do Sul, Brazil. The samples were extracted using the EPA method TO-13A and 16 Polycyclic Aromatic Hydrocarbons (PAHs) were analyzed using a gaseous chromatograph coupled with a mass spectrometer (GC-MS). Also, the data discussed in this study were analyzed to identify the relations of the PAHs concentrations with NOx, NO, O3 and meteorological parameters (temperature, solar radiation, wind speed, relative humidity). The results showed that in winter, concentrations of total PAHs were significantly higher than in summer, thus showing their seasonal variation. The identification of emission sources by applying diagnostic ratios confirmed that PAHs in the study area originate from mobile sources, especially, from diesel and gasoline emissions. The analysis by PMF receptor model showed the contribution of these two main sources of emissions, too, followed by coal combustion, incomplete combustion/unburned petroleum and wood combustion. The toxic equivalent factors were calculated to characterize the risk of cancer from PAH exposure to PM1.0 samples, and BaP and DahA dominated BaPeq levels.

  17. Chemical mass balance source apportionment of fine and PM10 in the Desert Southwest, USA

    EPA Science Inventory

    The Desert Southwest Coarse Particulate Matter Study was undertaken in Pinal County, Arizona, to better understand the origin and impact of sources of fine and coarse particulate matter (PM) in rural, arid regions of the U.S. southwestern desert. The desert southwest experiences ...

  18. Chemical characterization of fine organic aerosol for source apportionment at Monterrey, Mexico

    NASA Astrophysics Data System (ADS)

    Mancilla, Y.; Mendoza, A.; Fraser, M. P.; Herckes, P.

    2015-07-01

    Primary emissions from anthropogenic and biogenic sources as well as secondary formation are responsible for the pollution levels of ambient air in major urban areas. These sources release fine particles into the air that negatively impact human health and the environment. Organic molecular markers, which are compounds that are unique to specific PM2.5 sources, can be utilized to identify the major emission sources in urban areas. In this study, 43 representative PM2.5 samples, for both daytime and nighttime periods, were built from individual samples collected in an urban site of the Monterrey Metropolitan Area (MMA) during the spring and fall of 2011 and 2012. The samples were analyzed for organic carbon, elemental carbon, and organic molecular markers. Several diagnostic tools were employed for the preliminary identification of emission sources. Organic compounds for eight compound classes were quantified. The n-alkanoic acids were the most abundant, followed by n-alkanes, wood smoke markers, and levoglucosan/alkenoic acids. Polycyclic aromatic hydrocarbons (PAHs) and hopanes were less abundant. The carbon preference index (0.7-2.6) for n-alkanes indicate a major contribution of anthropogenic and mixed sources during the fall and the spring, respectively. Hopanes levels confirmed the contribution from gasoline and diesel engines. In addition, the contribution of gasoline and diesel vehicle exhaust was confirmed and identified by the PAH concentrations in PM2.5. Diagnostic ratios of PAH showed emissions from burning coal, wood, biomass, and other fossil fuels. The total PAH and elemental carbon (EC) were correlated (r2 = 0.39-0.70) across the monitoring periods, reinforcing that motor vehicles are the major contributors of PAH. Cholesterol levels remained constant during the spring and fall, showing evidence of the contribution of meat cooking operations, while the isolated concentrations of levoglucosan suggested occasional biomass burning events. Finally

  19. Size-resolved source apportionment of particulate matter in urban Beijing during haze and non-haze episodes

    NASA Astrophysics Data System (ADS)

    Tian, S. L.; Pan, Y. P.; Wang, Y. S.

    2016-01-01

    Additional size-resolved chemical information is needed before the physicochemical characteristics and sources of airborne particles can be understood; however, this information remains unavailable in most regions of China due to lacking measurement data. In this study, we report observations of various chemical species in size-segregated particle samples that were collected over 1 year in the urban area of Beijing, a megacity that experiences severe haze episodes. In addition to fine particles, high concentrations of coarse particles were measured during the periods of haze. The abundance and chemical compositions of the particles in this study were temporally and spatially variable, with major contributions from organic matter and secondary inorganic aerosols. The contributions of organic matter to the particle mass decreased from 37.9 to 31.2 %, and the total contribution of sulfate, nitrate and ammonium increased from 19.1 to 33.9 % between non-haze and haze days, respectively. Due to heterogeneous reactions and hygroscopic growth, the peak concentrations of the organic carbon, cadmium and sulfate, nitrate, ammonium, chloride and potassium shifted from 0.43 to 0.65 µm on non-haze days to 0.65-1.1 µm on haze days. Although the size distributions of lead and thallium were similar during the observation period, their concentrations increased by a factor of more than 1.5 on haze days compared with non-haze days. We observed that sulfate and ammonium, which have a size range of 0.43-0.65 µm, sulfate and nitrate, which have a size range of 0.65-1.1 µm, calcium, which has a size range of 5.8-9 µm, and the meteorological factors of relative humidity and wind speed were responsible for haze pollution when the visibility was less than 10 km. Source apportionment using Positive Matrix Factorization showed six PM2.1 sources and seven PM2.1-9 common sources: secondary inorganic aerosol (25.1 % for fine particles vs. 9.8 % for coarse particles), coal combustion (17

  20. Source apportionment of particulate matter in the US and associations with lung inflammatory markers

    SciTech Connect

    Duvall, R.M.; Norris, G.A.; Dailey, L.A.; Burke, J.M.; McGee, J.K.; Gilmour, M.I.; Gordon, T.; Devlin, R.B.

    2008-07-01

    Size-fractionated particulate matter (PM) samples were collected from six U.S. cities and chemically analyzed as part of the Multiple Air Pollutant Study. Particles were administered to cultured lung cells and the production of three different proinflammatory markers was measured to explore the association between the health effect markers and PM. Ultrafine, fine, and coarse PM samples were collected between December 2003 and May 2004 over a 4-wk period in each city. Filters were pooled for each city and the PM samples were extracted then analyzed for trace metals, ions, and elemental carbon. Particle extracts were applied to cultured human primary airway epithelial cells, and the secreted levels of interleukin-8 (IL-8), heme oxygenase-1, and cyclooxygenase-2 were measured 1 and 24 h following exposure. Fine PM sources were quantified by the chemical mass balance (CMB) model. The relationship between toxicological measures, PM sources, and individual species were evaluated using linear regression. Ultrafine and fine PM mass were associated with increases in IL-8 (r{sup 2} = .80 for ultrafine and r{sup 2} = .52 for fine). Sources of fine PM and their relative contributions varied across the sampling sites and a strong linear association was observed between IL-8 and secondary sulfate from coal combustion (r{sup 2} = .79). Ultrafine vanadium, lead, copper, and sulfate were also associated with increases in IL-8. Increases in inflammatory markers were not observed for coarse PM mass and source markers. These findings suggest that certain PM size fractions and sources are associated with markers of lung injury or inflammation.

  1. Aerosol black carbon quantification in the central Indo-Gangetic Plain: Seasonal heterogeneity and source apportionment

    NASA Astrophysics Data System (ADS)

    Vaishya, Aditya; Singh, Prayagraj; Rastogi, Shantanu; Babu, S. Suresh

    2017-03-01

    Two years of aerosol spectral light absorption measurements, using filter based technique, from the central Indo-Gangetic plain (IGP), Gorakhpur (26.75°N, 83.38°E, 85 m amsl), are analyzed to study their seasonal behavior and to quantify their magnitude in terms of absorbing aerosols loading and source speciation. Spectral absorption analysis reveals a four-fold enhancement in absorption in winter (W) and post-monsoon (PoM) seasons at UV wavelengths as compared to IR wavelengths on account of increased biomass burning aerosol contribution to total absorbing aerosol load. Aerosols from the biomass sources contribute 28% during W and PoM seasons as against 16% in pre-monsoon (PM) and monsoon (M) seasons to the total absorbing aerosol content. A Mode shift in the distribution of the Absorption Ångström exponent (α) from 1.3 to 1.6 from PM-M seasons to PoM-W seasons signifies change in source type of absorbing aerosols from fossil fuel to biomass burning and their relative source strength. Due to near stagnant wind conditions combined with shallow boundary layer height, where air masses travelling to the central IGP are confined to a smaller volume, in W and PoM seasons, local sources assume more prominence rather than long-range transport of aerosols. Long-term measurements of aerosols physicochemical and radiative properties from this measurement location will enhance our understanding of the complex aerosol system over the IGP and its climatic implications.

  2. Large chemical characterisation of PM10 emitted from graphite material production: Application in source apportionment.

    PubMed

    Golly, B; Brulfert, G; Berlioux, G; Jaffrezo, J-L; Besombes, J-L

    2015-12-15

    This work focuses on emissions from industrial sources that are still poorly understood in Europe, especially the "carbon industry". The study is based on two intensive sampling campaigns performed in a graphite material production plant for 2weeks in July 2013 and November 2013 in alpine valleys. The chemical characterization of PM10 was conducted at three sampling sites (outdoor and indoor sites) located inside one industrial area, which is considered as the highest emissions source of polycyclic aromatic hydrocarbons (PAHs) in the Arve valley. The identification of specific tracers among metals and trace elements is commonly used to characterize industrial emissions. In our study, original enrichment factors relative to the "rural exposed background" have been calculated, and the metallic fraction was not affected by this industrial source. In contrast, the organic fraction of PM10 has a number of features, providing a complete organic source profile and referred to as the "carbon industry". In particular, polycyclic aromatic sulfur heterocycles (PASH) have been largely detected from fugitive emissions with rather large concentrations. The average concentrations of benzo(b)naphtho(2,1-d)thiophene (BNT(2,1)) reached 2.35-6.56ng·m(-3) and 60.5-376ng·m(-3) for outdoor and indoor sites, respectively. The use of this reference profile in the chemical mass balance model (CMB) applied to samples collected in two sites near industrial areas shows that this source had an average contribution of 6% of the organic matter (OM) mass during the sampling period during the winter of 2013.

  3. Hydrocarbon source apportionment for the 1996 Paso del Norte Ozone Study.

    PubMed

    Fujita, E M

    2001-08-10

    The 1996 Paso del Norte (PdN) ozone study was conducted to improve current understanding of the significant meteorological and air quality processes that lead to high concentrations of ozone in El Paso, Texas (USA) and Ciudad Juárez, Chihuahua (Mexico). Two-hour canister samples were collected five times daily at 05.00-07.00 h, 07.00-09.00 h, 09.00-11.00 h, 11.00-13.00 h, and 15.00-17.00 h MST during intensive study periods at one urban and one rural site on each side of the border. An automated gas chromatograph was operated at one site in central El Paso. Source profiles (the fractional chemical composition of emissions) from motor vehicles, gasoline, liquefied petroleum gas, and commercial natural gas were combined with source profiles from other studies for input to the Chemical Mass Balance (CMB) receptor model to apportion the measured non-methane hydrocarbons (NMHC) to sources. On-road vehicle emissions accounted for one-half to two-thirds of the NMHC in Ciudad Juárez and El Paso with the highest contributions occurring during the morning and afternoon commute periods. Emissions from diesel exhaust contributed approximately 2-3% of NMHC in Ciudad Juárez and less than 2% in El Paso. The average sum of liquid gasoline and gasoline vapor increased during the day in Ciudad Juárez from 2% at 06.00 h to approximately 12% at 16.00 h. Diurnal and day-of-the-week patterns in the liquid gasoline contributions are essentially identical to the corresponding patterns for motor vehicle exhaust, which suggest that a large fraction of the liquid gasoline contribution may be associated with tailpipe emissions rather than evaporative emissions from motor vehicles or industrial sources. Including the sum of the two sources put the upper limit for tailpipe contributions at 60-70% of NMHC.

  4. PM2.5 pollution in a megacity of southwest China: source apportionment and implication

    NASA Astrophysics Data System (ADS)

    Tao, J.; Gao, J.; Zhang, L.; Zhang, R.; Che, H.; Zhang, Z.; Lin, Z.; Jing, J.; Cao, J.; Hsu, S.-C.

    2014-08-01

    Daily PM2.5 (aerosol particles with an aerodynamic diameter of less than 2.5 μm) samples were collected at an urban site in Chengdu, an inland megacity in southwest China, during four 1-month periods in 2011, with each period in a different season. Samples were subject to chemical analysis for various chemical components ranging from major water-soluble ions, organic carbon (OC), element carbon (EC), trace elements to biomass burning tracers, anhydrosugar levoglucosan (LG), and mannosan (MN). Two models, the ISORROPIA II thermodynamic equilibrium model and the positive matrix factorization (PMF) model, were applied to explore the likely chemical forms of ionic constituents and to apportion sources for PM2.5. Distinctive seasonal patterns of PM2.5 and associated main chemical components were identified and could be explained by varying emission sources and meteorological conditions. PM2.5 showed a typical seasonality of waxing in winter and waning in summer, with an annual mean of 119 μg m-3. Mineral soil concentrations increased in spring, whereas biomass burning species elevated in autumn and winter. Six major source factors were identified to have contributed to PM2.5 using the PMF model. These were secondary inorganic aerosols, coal combustion, biomass burning, iron and steel manufacturing, Mo-related industries, and soil dust, and they contributed 37 ± 18, 20 ± 12, 11 ± 10, 11 ± 9, 11 ± 9, and 10 ± 12%, respectively, to PM2.5 masses on annual average, while exhibiting large seasonal variability. On annual average, the unknown emission sources that were not identified by the PMF model contributed 1 ± 11% to the measured PM2.5 mass. Various chemical tracers were used for validating PMF performance. Antimony (Sb) was suggested to be a suitable tracer of coal combustion in Chengdu. Results of LG and MN helped constrain the biomass burning sources, with wood burning dominating in winter and agricultural waste burning dominating in autumn. Excessive Fe (Ex

  5. PM2.5 pollution in a megacity of southwest China: source apportionment and implication

    NASA Astrophysics Data System (ADS)

    Tao, J.; Gao, J.; Zhang, L.; Zhang, R.; Che, H.; Zhang, Z.; Lin, Z.; Jing, J.; Cao, J.; Hsu, S.-C.

    2014-02-01

    Daily PM2.5 (aerosol particles with an aerodynamic diameter of less than 2.5 μm) samples were collected at an urban site in Chengdu, an inland megacity in southwest China, during four one-month periods in 2011, with each period in a different season. Samples were subjected to chemical analysis for various chemical components ranging from major water-soluble ions, organic carbon (OC), element carbon (EC), trace elements to biomass burning tracers, anhydrosugar levoglucosan (LG) and mannosan (MN). Two models, ISORROPIA-II thermodynamic equilibrium model and positive matrix factorization (PMF) model, were applied to explore the likely chemical forms of ionic constituents and to apportion sources for PM2.5. Distinctive seasonal patterns of PM2.5 and associated main chemical components were identified and could be explained by varying emission sources and meteorological conditions. PM2.5 showed a typical seasonality of waxing in winter and waning in summer, with an annual mean of 119 μg m-3. Mineral soil concentrations increased in spring whereas biomass burning species elevated in autumn and winter. Six major source factors were identified to have contributed to PM2.5 using the PMF model. These were secondary inorganic aerosols, coal combustion, biomass burning, iron and steel manufacturing, Mo-related industries, and soil dust, and they contributed 37 ± 18%, 20 ± 12%, 11 ± 10%, 11 ± 9%, 11 ± 9%, and 10 ± 12%, respectively, to PM2.5 masses on annual average, while exhibiting large seasonal variability. On annual average, the unknown emission sources that were not identified by the PMF model contributed 1 ± 11% to the measured PM2.5 mass. Various chemical tracers were used for validating PMF performance. Antimony (Sb) was suggested to be a suitable tracer of coal combustion in Chengdu. Results of LG and MN helped constrain the biomass burning sources, with wood burning dominating in winter and agricultural waste burning dominating in autumn. Excessive Fe (Ex

  6. Measurement of Greenhouse gases (GHGs) and source apportionment in Bakersfield, CA during CalNex 2010

    NASA Astrophysics Data System (ADS)

    Guha, A.; Gentner, D. R.; Weber, R.; Gardner, A.; Provencal, R. A.; Goldstein, A. H.

    2011-12-01

    The California Global Warming Solutions Act 2006 (AB 32) creates a need to verify and validate the state GHG inventory, which is largely based on activity data and emission factor based estimates. The "bottom-up" emission factors for methane (CH4) and nitrous oxide (N2O) have large uncertainties and there is a lack of adequate "top-down" measurements to characterize emission rates from sources. Emissions from non-CO2 GHG sources display spatial heterogeneity and temporal variability, and are thus, often, poorly characterized. The Central Valley of California is an agriculture and industry intensive region with huge concentration of dairies, refineries and active oil fields which are known CH4 sources. As part of the CalNex campaign, we performed measurements of principal trace GHG gases (CO2, CH4, and N2O) and combustion tracer CO at the Bakersfield super-site during the summer of 2010. Measurements were made over a period of six weeks using fast response lasers based on cavity enhanced absorption spectroscopy (LGR Inc. CA). Coincident measurements of hundreds of volatile organic compounds (VOCs) served as anthropogenic and biogenic tracers of the GHG sources at local and regional levels. The local mean CH4 (1.93ppm) and N2O (325ppb) minimum are larger than that measured at Mauna Loa (NOAA). Daytime winds from the north-west draw emissions from the city center, Fruitvale oilfield and two refineries. Huge enhancements of CH4 relative to CO2 (> 4ppm of CH4) are seen on some days but almost on each night, when wind reversal and valley backflow brings winds from the east (oil fields and landfill). Winds from south-southwest (dairies) have ΔCH4 / ΔCO2 ratios similar to previous dairy chamber studies (Mitloehner et al., 2009). The ΔCH4 / ΔCO ratios at Bakersfield are much larger than that calculated downwind of Los Angeles at Mt. Wilson (Hsu et al., 2009) or in-flight measurements during CalNex (NOAA) suggesting additional non-combustion sources strongly influence

  7. Source apportionment of sediment-associated aliphatic hydrocarbon in a eutrophicated shallow lake, China.

    PubMed

    Wang, Ji-Zhong; Yang, Ze-Yu; Chen, Tian-Hu

    2012-11-01

    Chaohu Lake, one of the most eutrophicated lakes in China, has been suffering from long-term outside pollution, urban sewage, river outflows, and agricultural runoff which expectedly have been the main contributors of hydrocarbons. However, the contributions from these various sources have not been specified. The present study is aimed at identifying the potential sources of hydrocarbons in surface sediment around the whole lake and assessing the relative contributions using principal components analysis-multiple linear regression (PCA-MLR). Sixty-one surface sediments covering the whole Chaohu Lake and three main estuaries of inflowing rivers were collected, dried, extracted, and analyzed for 27 normal alkanes (n-alkanes, from C(12) to C(38), defined Σ(27)AH) and unresolved complex mixture (UCM) by GC/MS. Diagnostic ratios and PCA-MLR were utilized to apportion their sources. The concentrations of Σ(27)AH and UCM ranged from 434 to 3,870 ng/g and 11.9 to 325 μg/g dry weight, respectively, for all samples. The concentrations of Σ(27)AH in western region and estuary of Nanfei River were slightly higher but without statistical significance than those from eastern region and estuaries of Yuxi River and Hangbu River. The concentration of UCM from western region was significantly higher than that obtained from eastern region. These results reflect the importance of input of urban runoff by Nanfei River and serious eutrophication in western region. Aliphatic hydrocarbons in Chaohu Lake were mainly derived from high plant wax with mixed sources of phytoplankton and petroleum. Weak microbial decomposition of n-alkanes would be expected to occur from the low ratios of isoprenoid hydrocarbons pristine (pri) and phytane (phy) to n-C(17) and n-C(18), respectively. Higher plant, fossil combustion, petroleum residue, and phytoplankton were proposed as the main origines of aliphatic hydrocarbons by PCA while the contributions of individual n-alkane homologues, pri and phy

  8. Source apportionment of stack emissions from research and development facilities using positive matrix factorization

    NASA Astrophysics Data System (ADS)

    Ballinger, Marcel Y.; Larson, Timothy V.

    2014-12-01

    Research and development (R&D) facility emissions are difficult to characterize due to their variable processes, changing nature of research, and large number of chemicals. Positive matrix factorization (PMF) was applied to volatile organic compound (VOC) concentrations measured in the main exhaust stacks of four different R&D buildings to identify the number and composition of major contributing sources. PMF identified between 9 and 11 source-related factors contributing to stack emissions, depending on the building. Similar factors between buildings were major contributors to trichloroethylene (TCE), acetone, and ethanol emissions; other factors had similar profiles for two or more buildings but not all four. At least one factor for each building was identified that contained a broad mix of many species and constraints were used in PMF to modify the factors to resemble more closely the off-shift concentration profiles. PMF accepted the constraints with little decrease in model fit.

  9. Source apportionment of atmospheric mercury pollution in China using the GEOS-Chem model.

    PubMed

    Wang, Long; Wang, Shuxiao; Zhang, Lei; Wang, Yuxuan; Zhang, Yanxu; Nielsen, Chris; McElroy, Michael B; Hao, Jiming

    2014-07-01

    China is the largest atmospheric mercury (Hg) emitter in the world. Its Hg emissions and environmental impacts need to be evaluated. In this study, China's Hg emission inventory is updated to 2007 and applied in the GEOS-Chem model to simulate the Hg concentrations and depositions in China. Results indicate that simulations agree well with observed background Hg concentrations. The anthropogenic sources contributed 35-50% of THg concentration and 50-70% of total deposition in polluted regions. Sensitivity analysis was performed to assess the impacts of mercury emissions from power plants, non-ferrous metal smelters and cement plants. It is found that power plants are the most important emission sources in the North China, the Yangtze River Delta (YRD) and the Pearl River Delta (PRD) while the contribution of non-ferrous metal smelters is most significant in the Southwest China. The impacts of cement plants are significant in the YRD, PRD and Central China.

  10. Source apportionment of polychlorinated biphenyls in the sediments of the Delaware River.

    PubMed

    Praipipat, Pornsawai; Rodenburg, Lisa A; Cavallo, Gregory J

    2013-05-07

    Polychlorinated biphenyls (PCBs) are toxic, persistent, bioaccumulative compounds that threaten water quality in many areas, including the Delaware River. In 2003, total maximum daily loads for PCBs were promulgated for the tidal portion of the river, requiring the collection of a massive and unprecedented data set on PCBs in an urban estuary using state of the art, high-resolution high mass spectrometry (EPA method 1668 revision A). In previous publications, this data set has been examined using positive matrix factorization (PMF) to apportion PCB sources in the air, water, and permitted discharges to the river. Here, the same technique is used to apportion PCB sources in the sediment. This holistic approach allows the comparison of source types and magnitudes to the air, water, and sediment, and allows conclusions to be drawn about the cycling of PCBs in a typical urbanized estuary. A data set containing 87 chromatographic peaks representing 132 PCB congeners in 81 samples and 6 duplicated samples was analyzed. Seven factors were resolved. Three represent relatively unweathered Aroclors. Two were related to the non-Aroclor sources of diarylide yellow pigments and titanium tetrachloride production. The two remaining factors were probably originally related to Aroclors, but they are so highly weathered as to be unrecognizable as Aroclors, and thus have probably resided in the river for a long time. Comparing the abundance of the resolved PCB factors in the air, water, discharges, and sediment demonstrates that high molecular weight formulations, such as Aroclor 1260 and PCBs 206, 208, and 209 produced during titanium tetrachloride synthesis accumulate preferentially in the sediment, in keeping with their greater hydrophobicity. In contrast, lower molecular weight formulations, including the products of PCB dechlorination occurring in sewers, do not accumulate appreciably. PCB 11 from pigment use does accumulate in sediments and also seems to be distributed

  11. Measurement and apportionment of radon source terms for modeling indoor environments

    SciTech Connect

    Harley, N.H.

    1992-01-01

    This research has two main goals; (1) to quantify mechanisms for radon entry into homes of different types and to determine the fraction of indoor radon attributable to each source and (2) to model and calculate the dose (and therefore alpha particle fluence) to cells in the human and animal tracheobronchial tree that is pertinent to induction of bronchogenic carcinoma from inhaled radon daughters. The dosimetry has been extended to include organs other than the lung.

  12. Radiocarbon Analysis Source Apportionment of Fossil and Modern Atmospheric Carbon from DISCOVER-AQ Houston

    NASA Astrophysics Data System (ADS)

    Ortiz, S. M.; Yoon, S.; Barrett, T. E.; Usenko, S.; Sheesley, R. J.

    2015-12-01

    DISCOVER-AQ (Deriving Information on Surface Conditions from Column and Vertically Resolved Observations Resolved Observations Relevant to Air Quality) is a sampling campaign aimed to monitor regional atmospheric pollutants within a collection of cities across the United States. In September 2013, ground-based air samplers were placed selectively to represent the city of Houston: Moody Tower (downtown; urban) and Manvel Croix (southern; suburb), Conroe (far north; suburb) and La Porte (east; urban industrial), with the goal of understanding particulate matter sources and composition and exposure in urban communities. Radiocarbon analysis was conducted on TSP (total suspended particulate matter) and PM2.5 (particulate matter less than 2.5 μm in aerodynamic diameter) from ground-based samplers. Radiocarbon is used to determine the contributions of contemporary and fossil sources to carbonaceous aerosol in Houston. Contemporary sources of atmospheric carbon in TSP and PM2.5 include primary biogenic emissions, biomass combustion and SOA produced in the atmosphere from biogenic- and biomass combustion-derived volatile organic carbon. Fossil sources of atmospheric carbon in PM2.5 and TSP include all types of primary fossil fuel combustion and SOA produced in the atmosphere from fossil-derived volatile organic carbon. Results from the last week of the campaign, September 21-28th, displayed a PM2.5 contemporary carbon fraction of 48-78% for Moody Tower, 59-86% for Manvel Croix, 66-89% for Conroe. Ambient TSP had contemporary carbon fractions of 51-65% for Moody Tower and 51-83% for La Porte.

  13. Source Apportionment of PM10 by Positive Matrix Factorization in Urban Area of Mumbai, India

    PubMed Central

    Gupta, Indrani; Salunkhe, Abhaysinh; Kumar, Rakesh

    2012-01-01

    Particulate Matter (PM10) has been one of the main air pollutants exceeding the ambient standards in most of the major cities in India. During last few years, receptor models such as Chemical Mass Balance, Positive Matrix Factorization (PMF), PCA–APCS and UNMIX have been used to provide solutions to the source identification and contributions which are accepted for developing effective and efficient air quality management plans. Each site poses different complexities while resolving PM10 contributions. This paper reports the variability of four sites within Mumbai city using PMF. Industrial area of Mahul showed sources such as residual oil combustion and paved road dust (27%), traffic (20%), coal fired boiler (17%), nitrate (15%). Residential area of Khar showed sources such as residual oil combustion and construction (25%), motor vehicles (23%), marine aerosol and nitrate (19%), paved road dust (18%) compared to construction and natural dust (27%), motor vehicles and smelting work (25%), nitrate (16%) and biomass burning and paved road dust (15%) in Dharavi, a low income slum residential area. The major contributors of PM10 at Colaba were marine aerosol, wood burning and ammonium sulphate (24%), motor vehicles and smelting work (22%), Natural soil (19%), nitrate and oil burning (18%). PMID:22645437

  14. Spatial distribution and source apportionment of PFASs in surface sediments from five lake regions, China

    PubMed Central

    Qi, Yanjie; Huo, Shouliang; Xi, Beidou; Hu, Shibin; Zhang, Jingtian; He, Zhuoshi

    2016-01-01

    Perfluoroalkyl substances (PFASs) have been found in environment globally. However, studies on PFAS occurrence in sediments of lakes or reservoirs remain relatively scarce. In this study, two hundred and sixty-two surface sediment samples were collected from forty-eight lakes and two reservoirs all over China. Average PFAS concentrations in surface sediments from each lake or reservoir varied from 0.086 ng/g dw to 5.79 ng/g dw with an average of 1.15 ng/g dw. Among five lake regions, average PFAS concentrations for the lakes from Eastern Plain Region were the highest. Perfluorooctanoic acid, perfluoroundecanoic acid and perfluorooctane sulfonic acid (PFOS) were the predominant PFASs in surface sediments. The significant positive correlations between PFAS concentrations and total organic carbon, total nitrogen and total phosphorus contents in sediments revealed the influences of sedimentary characteristics on PFAS occurrence. A two-dimensional hierarchical cluster analysis heat map was depicted to analyze the possible origins of sediments and individual PFAS. The food-packaging, textile, electroplating, firefighting and semiconductor industry emission sources and the precious metals and coating industry emission sources were identified as the main sources by two receptor models, with contributions of 77.7 and 22.3% to the total concentrations of C4-C14- perfluoroalkyl carboxylic acids and PFOS, respectively. PMID:26947748

  15. Hydrochemical evaluation of surface water quality and pollution source apportionment in the Luan River basin, China.

    PubMed

    Wang, Huiliang; Li, Xuyong; Xie, Ying

    2011-01-01

    In the context of rapid economic growth in China, hydrochemical characteristics of stream water quality are being influenced by a variety of natural and anthropogenic inputs. We determined 10 hydrochemical parameters of the surface water at 29 monitoring sites in the Luan River basin of northern China during 2007-2009. Water quality hydrochemistry was evaluated using fuzzy comprehensive analysis based on the National Surface Water Environmental Quality Standards of China. Our results showed that 14 sites were classified as 'meeting standard (MS)' while the other 15 sites were classified 'non-meeting standard (NS)'. According to principal component analysis, four potential pollution sources were identified that explained 80.6% of the total variance among these MS sites, and three potential pollution sources that explained 78.3% of the total variance among these NS sites. Furthermore, multi-linear regression of the absolute principal component scores was used to estimate contributions from identified pollution sources. Most water pollution variables were influenced primarily by municipal sewage and non-point pollution in MS sites. In NS sites, chemical industry wastewater pollution dominated. Pollution in the main stream was more serious than that in the small tributaries. Our findings provide useful information for developing better pollution control strategies for the Luan River.

  16. Source apportionment of polychlorinated biphenyls in the New York/New Jersey Harbor.

    PubMed

    Rodenburg, Lisa A; Du, Songyan; Xiao, Baohua; Fennell, Donna E

    2011-04-01

    The New York/New Jersey Harbor (also known as the Hudson River Estuary) is heavily contaminated with polychlorinated biphenyls (PCBs) arising in part from inputs from the Upper Hudson River, which is a Superfund site containing historical PCB contamination, and also due to inputs from the New York City metropolitan area. The Contamination Assessment and Reduction Project (CARP) measured PCBs and other contaminants in ambient water samples collected throughout the Harbor region during 1998-2001. In order to investigate the sources of PCBs to the NY/NJ Harbor, this data base of PCB concentrations was analyzed using Positive Matrix Factorization (PMF). This analysis resolved seven factors that are thought to be associated with sources such as the Upper Hudson River, storm water runoff, combined sewer overflows (CSOs), and wastewater effluents. The PMF model also produced a factor that appears to be related to sites contaminated with Aroclor 1260. To the extent that the NY/NJ Harbor is typical of urbanized estuaries throughout the United States, these results suggest that storm water runoff is probably a significant source of PCBs to surface waters in urban areas.

  17. Hydrocarbon source apportionment in Mexico City using the chemical mass balance receptor model

    NASA Astrophysics Data System (ADS)

    Vega, Elizabeth; Mugica, Violeta; Carmona, Rocío.; Valencia, Edgar

    A field study was conducted in Mexico City during May-November 1997 to determine non-methane hydrocarbons (NMHC) species emitted from different sources: application of slow curing asphalt pavement, liquefied petroleum gas (vapour phase), dry cleaning, graphic arts, landfill, emissions of motor vehicle exhaust inside a tunnel, hot soak, whole gasoline, painting operations and degreasing. Forty-five ambient air samples of NMHC were simultaneously collected from 6:00 to 9:00 a.m. at three different sites, Xalostoc, Pedregal and La Merced, denominated receptors, during the spring and fall of 1996. In both cases samples were collected in stainless-steel canisters and analysed by gas chromatography with flame ionisation detection system. Based on these measurements the chemical mass receptor model (CMB) was applied to estimate the contribution of the different NMHC source to ambient pollution. The average results for the two sampling periods showed that the major sources of NMHC for the three sites were: motor vehicle exhaust with an average contribution of 54.9, 57.4 and 63.8% for Xalostoc, Pedregal and La Merced, respectively, followed by handling and distribution of liquefied petroleum gas with 28.5% in Xalostoc, 20.0% in Pedregal and 24.0% in La Merced.

  18. Source Apportionment of Particle Bound Polycyclic Aromatic Hydrocarbons at an Industrial Location in Agra, India

    PubMed Central

    Lakhani, Anita

    2012-01-01

    16 US EPA priority polycyclic aromatic hydrocarbons (PAHs) were quantified in total suspended ambient particulate matter (TSPM) collected from an industrial site in Agra (India) using gas chromatography. The major industrial activities in Agra are foundries that previously used coal and coke as fuel in cupola furnaces. These foundries have now switched over to natural gas. In addition, use of compressed natural gas has also been promoted and encouraged in automobiles. This study attempts to apportion sources of PAH in the ambient air and the results reflect the advantages associated with the change of fuel. The predominant PAHs in TSPM include high molecular weight (HMW) congeners BghiP, DbA, IP, and BaP. The sum of 16 priority PAHs had a mean value of 72.7 ± 4.7 ng m−3. Potential sources of PAHs in aerosols were identified using diagnostic ratios and principal component analysis. The results reflect a blend of emissions from diesel and natural gas as the major sources of PAH in the city along with contribution from emission of coal, coke, and gasoline. PMID:22606062

  19. Spatial distribution and source apportionment of PFASs in surface sediments from five lake regions, China

    NASA Astrophysics Data System (ADS)

    Qi, Yanjie; Huo, Shouliang; Xi, Beidou; Hu, Shibin; Zhang, Jingtian; He, Zhuoshi

    2016-03-01

    Perfluoroalkyl substances (PFASs) have been found in environment globally. However, studies on PFAS occurrence in sediments of lakes or reservoirs remain relatively scarce. In this study, two hundred and sixty-two surface sediment samples were collected from forty-eight lakes and two reservoirs all over China. Average PFAS concentrations in surface sediments from each lake or reservoir varied from 0.086 ng/g dw to 5.79 ng/g dw with an average of 1.15 ng/g dw. Among five lake regions, average PFAS concentrations for the lakes from Eastern Plain Region were the highest. Perfluorooctanoic acid, perfluoroundecanoic acid and perfluorooctane sulfonic acid (PFOS) were the predominant PFASs in surface sediments. The significant positive correlations between PFAS concentrations and total organic carbon, total nitrogen and total phosphorus contents in sediments revealed the influences of sedimentary characteristics on PFAS occurrence. A two-dimensional hierarchical cluster analysis heat map was depicted to analyze the possible origins of sediments and individual PFAS. The food-packaging, textile, electroplating, firefighting and semiconductor industry emission sources and the precious metals and coating industry emission sources were identified as the main sources by two receptor models, with contributions of 77.7 and 22.3% to the total concentrations of C4-C14- perfluoroalkyl carboxylic acids and PFOS, respectively.

  20. Source apportionment advances using polar plots of bivariate correlation and regression statistics

    NASA Astrophysics Data System (ADS)

    Grange, Stuart K.; Lewis, Alastair C.; Carslaw, David C.

    2016-11-01

    This paper outlines the development of enhanced bivariate polar plots that allow the concentrations of two pollutants to be compared using pair-wise statistics for exploring the sources of atmospheric pollutants. The new method combines bivariate polar plots, which provide source characteristic information, with pair-wise statistics that provide information on how two pollutants are related to one another. The pair-wise statistics implemented include weighted Pearson correlation and slope from two linear regression methods. The development uses a Gaussian kernel to locally weight the statistical calculations on a wind speed-direction surface together with variable-scaling. Example applications of the enhanced polar plots are presented by using routine air quality data for two monitoring sites in London, United Kingdom for a single year (2013). The London examples demonstrate that the combination of bivariate polar plots, correlation, and regression techniques can offer considerable insight into air pollution source characteristics, which would be missed if only scatter plots and mean polar plots were used for analysis. Specifically, using correlation and slopes as pair-wise statistics, long-range transport processes were isolated and black carbon (BC) contributions to PM2.5 for a kerbside monitoring location were quantified. Wider applications and future advancements are also discussed.

  1. Source apportionment of particle bound polycyclic aromatic hydrocarbons at an industrial location in Agra, India.

    PubMed

    Lakhani, Anita

    2012-01-01

    16 U.S. EPA priority polycyclic aromatic hydrocarbons (PAHs) were quantified in total suspended ambient particulate matter (TSPM) collected from an industrial site in Agra (India) using gas chromatography. The major industrial activities in Agra are foundries that previously used coal and coke as fuel in cupola furnaces. These foundries have now switched over to natural gas. In addition, use of compressed natural gas has also been promoted and encouraged in automobiles. This study attempts to apportion sources of PAH in the ambient air and the results reflect the advantages associated with the change of fuel. The predominant PAHs in TSPM include high molecular weight (HMW) congeners BghiP, DbA, IP, and BaP. The sum of 16 priority PAHs had a mean value of 72.7 ± 4.7 ng m(-3). Potential sources of PAHs in aerosols were identified using diagnostic ratios and principal component analysis. The results reflect a blend of emissions from diesel and natural gas as the major sources of PAH in the city along with contribution from emission of coal, coke, and gasoline.

  2. Size-resolved source apportionment of airborne particle mass in a roadside environment.

    PubMed

    Riddle, Sarah G; Robert, Michael A; Jakober, Chris A; Hannigan, Michael P; Kleeman, Michael J

    2008-09-01

    Airborne particulate hopanes, steranes, and polycyclic aromatic hydrocarbons (PAHs) were measured in six size fractions < 1.8 microm particle diameter at one site upwind and two sites downwind of the Interstate 5 freeway in San Diego, CA. The smallest size fraction collected was exclusively in the ultrafine size range (D(p) < 0.1 microm; PM0.1). Size distributions of hopanes, steranes, and PAHs peaked between 0.10-0.18 microm particle aerodynamic diameter with a tail extending into the PM0.1 size range. This pattern is similar to previous dynamometer studies of hopane, sterane, and PAH size distributions emitted from gasoline- and diesel-powered vehicles. Size-resolved source profiles were combined to form an "on-road" profile for motor oil, diesel, and gasoline contributions to EC and OC. The resulting equations were used to predict source contributions to the size distributions of EC and OC in the roadside environment. The method successfully accounted for the majority of the carbonaceous material in particles with diameter < 0.18 microm, with significant residual material in larger size fractions. The peak in both the measured and predicted EC size distribution occurred between 0.1-0.18 microm particle aerodynamic diameter. The predicted OC size distribution peaked between 0.1-0.18 microm particle diameter, butthe measured OC size distribution peaked between 0.56-1.0 microm particle diameter, possibly because of secondary organic aerosol formation. Predicted OC concentrations in particles with diameter < 0.18 microm were greater than measured values 18 m downwind of the roadway but showed good agreement 37 m downwind. The largest source contributions to the PM0.1 and PM0.18 size fractions were different. PM0.18 was dominated by diesel fuel and motor oil combustion products while PM0.1 was dominated by diesel fuel and gasoline fuel combustion products. Total source contributions to ultrafine (PM0.1) EC concentrations 37 m downwind of the roadway were 44 +/- 6

  3. Source apportionment of ammonium and nitrate ion using nitrogen stable isotope

    NASA Astrophysics Data System (ADS)

    Kawashima, H.

    2013-12-01

    Suspended particulate matter (SPM), defined to particle size as 100 % cut-off aerodynamic diameter at 10 μm, has adverse effects on human health. In these years, stable isotope ratio of small sample volume can be analyzed high precision by isotope ratio mass spectrometry coupling with elemental analyzer. Recently some fields are using stable isotope ratio. For environmental field, it is expected such as powerful tool for source identification and understanding mechanism. But the existed researches intended for stable nitrogen isotope (δ15N) of particulate matter have been limited. We try to analysis δ15N-ammonium (δ15N-NH4+) and nitrate (δ15N-NO3-) of SPM, to estimate source of NH4+ and NO3- of SPM. Average δ15N-NH4+ and δ15N-NO3- of SPM in Akita prefecture, Japan were 15.9 ‰ (1.3‰ to 38.5 ‰) and - 0.7 ‰ (-4.6 ‰ to 4.8 ‰), respectively. Although δ15N-NH4+ do not show seasonal trend, δ15N-NO3- increased in winter markedly and decreasing in summer. In generally, the dominant origin of NO3- of SPM is produced from NOx emitted by combustion of some fuel and NO by agriculture source. Heaton (1990) summarized that δ15N-NOx is very different by temperature of combustion. They insisted that δ15N-NOx values are between -13 ‰ to -2 ‰ over 2000 °C (e.g. vehicle engine) and 6 ‰ to 13 ‰ under 1300 °C (e.g. coal combustion). Therefore, the reason of the winter high trend in this study might be combustion process such as coal combustion source. Moreover, the baseline might be made by vehicle sources. In addition, the reason of decreasing in summer seemed to be affected very low δ15N-NO of fertilizer and urea indicated by Li and Wang (2008). Bacteria were activated in summer, and NO from fertilizer and urea was emitted. This summary seemed to be very reasonable.

  4. Indoor PM2.5 in Santiago, Chile, spring 2012: Source apportionment and outdoor contributions

    NASA Astrophysics Data System (ADS)

    Barraza, Francisco; Jorquera, Héctor; Valdivia, Gonzalo; Montoya, Lupita D.

    2014-09-01

    Indoor and outdoor PM2.5 sampling campaigns were carried out at Santiago, Chile (6 million inhabitants, 33.5°S, 70.6°W) in spring 2012. A pair of samplers was placed inside each household studied and an additional pair of samplers was placed at a fixed outdoor location for measuring trace elements and elemental (EC) and organic carbon (OC) in Teflon and quartz filters, respectively. A total of 47 households in downtown Santiago were included in this study. Mean outdoor and indoor PM2.5 concentrations were 19.2 and 21.6 μg/m3, respectively. Indoor concentrations of PM2.5 were affected by socioeconomic status (p = 0.048) but no such evidence was found for PM2.5 species, except lead (p = 0.046). Estimated species infiltration factors were 0.70 (±0.19), 0.98 (±0.21), 0.80 (±0.12) and 0.80 (±0.03) for PM2.5, OC, EC and sulfur, respectively. Estimated household infiltration factors had a median of 0.75, mean of 0.78, standard deviation of 0.18 and interquartile range (IQR) 0.67-0.86. For the very first time, Positive Matrix Factorization (PMF3) was applied to an indoor PM2.5 chemical composition data set measured at Santiago. Source identification was carried out by inspection of key species and by comparison with published source profiles; six sources were identified. Three of them were outdoor contributions: motor vehicles with 5.6 (±0.7) μg/m3, street dust with 2.9 (±0.5) μg/m3 and secondary sulfates with 3.4 (±0.5) μg/m3. The indoor sources were: indoor dust with 1.6 (±0.3) μg/m3, cleaning and cooking with 2.3 (±0.3) μg/m3 and cooking and environmental tobacco smoke with 6.1 (±0.7) μg/m3. There is potential for further reducing PM2.5 population exposure in the short term -by improving ventilation of indoor air and controlling indoor sources - and in the long term - with filtration of outdoor air and household improvements to reduce air change rates.

  5. [Source Contribution Analysis of the Fine Particles in Shanghai During a Heavy Haze Episode in December, 2013 Based on the Particulate Matter Source Apportionment Technology].

    PubMed

    Li, Li; An, Jing-yu; Yan, Ru-sha

    2015-10-01

    The haze pollution caused by high PM2.5 concentrations has become one of the major environmental issues restricting urban and regional sustainable development in China in recent years. Therefore, the diagnosis of the pollution sources of PM2.5 and its major components in a scientific and efficient way is of great significance both scientifically and theoretically. A rare heavy haze pollution event occurred in Shanghai and the surrounding Yangtze River Delta in early December, 2013, that the hourly PM2.5 concentration reached 640 μg x m(-3). In this study, we analyzed the three typical episodes that occurred in Shanghai during this period. The particulate matter source apportionment technology (PSAT) was applied to study the source contributions to PM2.5 and its major components. Results showed that NO3-(2.5) were mostly contributed by industrial boilers and kilns, transportation and power plants. Comparatively, most of the SO4(2-) 2.5 came from industry and transport sectors. During the three episodes including haze, foggy haze and transport, local emissions contributed 35.3%, 44.8%, 22.7%, while super-regional transport accounted for 42.0%, 41.1% and 59.8% to PM2.5, respectively. In the YRD modeling domain, fugitive dust, industrial processing, volatile source, industrial boilers and kilns and transport were the major contributors to high concentrations of PM2.5, with the average contributions of 25.1%, 14.9%, 15.8%, 13.7% and 15.9%, respectively. Results showed that the very heavy haze pollution is usually not caused by a single city, the regional joint pollution control is of great importance to relieve the pollution level.

  6. Polycyclic Aromatic Hydrocarbon and Polychlorinated Biphenyl Trends and Source Apportionment in Europe Using Back Trajectories

    NASA Astrophysics Data System (ADS)

    Reimer, E.; Lammel, G.; Jarkovský, J.; Dvorská, A.

    2009-04-01

    Polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) are classes of organic substances with most of the individual substances being semivolatile and to some degree resisting degradation in the environment (persistent), hence, undergo long-range transport and reach pristine areas in high altitudes and latitudes. PCBs and even more so PAHs pose significant human health hazards in Europe (WHO, 2003). PAHs are emitted especially in incomplete combustion processes in both the gaseous and particulate phases (sorbed to soot). PCBs have been banned from most uses, such that re-emission and volatilization from old urban and industrial materials are prevailing atmospheric sources. As a consequence of fuel, combustion technology and legislative changes sources are changing in strength, substance pattern, and geographic distribution. Monitoring data in air at a central European continental background station, Košetice, Czech Republic, of 1997-2007 (Holoubek et al., 2007) were used in combination with back-trajectories to localize sources of selected PAHs and PCBs in central, western, eastern and southeastern Europe. The trajectory scheme uses the isentropic coordinate with some diabatic components and a special boundary layer modelling (Reimer & Scherer, 1992). Areal contact matrices over Europe are obtained by integration in time of the contacts of the backward trajectories with the ground (1x1 km2 grid) and weighting by the observed concentrations (or fictive concentrations of factors). Positive matrix factorization (Paatero, 1997) was used to infer the substance patterns of the sources (so-called factors) which most significantly contributed to PAH levels at Košetice and a second site, Leipzig, Germany. The interpretation of the results is based on matrices of transport to up to three receptor sites in central Europe. Potential source distributions are presented and discussed. The analysis of air pollution in Košetice in the periods 1997-99 and

  7. Source apportionment of absorbing aerosols in the central Indo-Gangetic Plain

    NASA Astrophysics Data System (ADS)

    Vaishya, Aditya; Singh, Prayagraj; Rastogi, Shantanu; Babu, S. Suresh

    2016-05-01

    Atmospheric aerosols in the Indo-Gangetic Plain (IGP) depicts high spatial and temporal heterogeneity in their radiative properties. Despite the fact that significant advancement in terms of characterizing aerosols radiative and physiochemical properties in the IGP have been made, information regarding the organic content towards total absorbing aerosol budget is lacking. In the present study we have analyzed two years of aerosol spectral light absorption measurements from the central-IGP, Gorakhpur (26.75°N, 83.38°E, 85m amsl), in order to study their seasonal behavior and to quantify their magnitude in terms of absorbing aerosols loading and source speciation. Remote sensing data in the form of 'Cloud corrected Fire Count' from MODIS Terra and 'Absorption Aerosol Index' from OMI satellites platform have been used to identify absorbing aerosol source regions. Spectral absorption analysis reveals a four-fold enhancement in absorption in the winter (W) and the post-monsoon (PoM) seasons at UV wavelengths as compared to 880 nm on account of increased biomass aerosol contribution to total absorbing aerosol load. Despite having higher fire events and absorption aerosol index, both indicating high biomass burning activities, in the pre-monsoon (PM) season, aerosols from the biomass sources contribute ~ 27% during the W and the PoM seasons as against ~17% in the PM season to the total absorbing aerosol content. This is due to near stagnant wind conditions and shallow height of air masses travelling to the central IGP in the W and the PoM seasons.

  8. Radiocarbon-Based Source apportionment of Elemental Carbon Aerosols at Seoul, South Korea

    NASA Astrophysics Data System (ADS)

    Shakerian Ghahferrokhi, Farid; Ahn, Jinho; Czimczik, Claudia I.; Holden, Sandra; Park, JinSoo

    2016-04-01

    In this study, 10 samples of PM2.5 (aerosol particle with diameter less than 2.5 μm) were collected in the Northeast of Seoul (37.60o N, 127.05o E), South Korea, over 2-4 day periods in May and June of 2015 with a high volume air sampler. The samples were analyzed for their bulk carbon (TC) and nitrogen (N) elemental and stable isotope composition with EA-IRMS. Elemental carbon (EC) was quantified with the Swiss_4S protocol using a Sunset OC/EC analyzer. Both, TC and EC were analyzed for their radiocarbon (14C) content via accelerator mass spectrometry. The mass and isotopic composition of organic carbon (OC) was quantified by (isotope) mass balance. TC loads were 6.6 +/- 1.5 ug C m-3 air (ave. +/- sd; range 4.7-9.7), with a ∆14C ranging from 240 to -446 per mill and a δ13C of -25.4+/-0.3 per mill. EC was a minor fraction of TC (7.2+/-1.9% or 0.5+/-0.2 ug C m-3 air). EC was strongly depleted in 14C (∆14C = -915 to -819 per mill), with fossil sources accounting for 88+/-3% of EC (6.3+/-1.7% of TC). OC was enriched in 14C above natural levels (∆14C = -401 to 309 per mill), and thus could not be partitioned into fossil and modern sources. Local wind directions showed that air masses originated from the South, demonstrating that regional sources may be the crucial contributor to PM pollution in Seoul during that sampling period (early summer).

  9. Occurrence and source apportionment of PAHs in highly vulnerable karst system.

    PubMed

    Shao, Yixian; Wang, Yanxin; Xu, Xiaoqing; Wu, Xiao; Jiang, Zhou; He, Shanshan; Qian, Kun

    2014-08-15

    The concentration and spatial distribution of polycyclic aromatic hydrocarbons (PAHs) in topsoil, groundwater and groundwater suspended solids (SS) at Guozhuang karst water system of northern China were investigated. The total concentration of PAHs ranged from 622 to 87,880 ng/g dry weight in topsoil, from 4739 to 59,314 ng/g dry weight in SS, and from 2137 to 9037 ng/L in groundwater, with mean values of 17,174 ng/g, 11,990 ng/g and 5020 ng/L, respectively. High concentrations of PAHs were mainly observed in the coal mining industrial area and the discharge area. The composition of PAHs indicated that low molecular weight PAHs were predominant in groundwater samples, the content of medium molecular weight PAHs was elevated in SS, and carcinogenic high molecular weight PAHs were frequently detected in topsoil. The high contents of low-medium molecular weight PAHs in groundwater and SS suggested relatively recent local sources of PAHs that were transported into the aquifer via leakage of contaminated surface water and/or infiltration of PAH-containing precipitation. The results of evaluating sources of PAHs using ratios of specific PAH compounds showed that PAHs mainly originated from coal and wood combustion. Furthermore, five sources were identified by positive matrix factorization (PMF) model, and the contribution to the total loadings of groundwater PAHs were: 2% for unburnt oil, 32% for coal combustion, 22% for vehicle emission, 27% for biomass combustion and 18% for coke production, respectively. Furthermore, strong correlations of total PAHs with total organic carbon (TOC) in topsoil indicated co-emission of PAHs and TOC. Poor correlations of PAHs with dissolved organic carbon (DOC) in groundwater indicated that other factors exert stronger influences. Therefore, PAHs might have posed a major threat to the quality of potable groundwater in Guozhuang karst water system.

  10. Source apportionment of particulate matter in Chinese megacities: the implication for emission control strategies

    NASA Astrophysics Data System (ADS)

    Huang, Ru-Jin; Elser, Miriam; Wang, Qiyuan Wang; Bozzetti, Carlo; Wolf, Robert; Wang, Yichen; Ni, Haiyan; Wang, Meng; Ho, Kin-Fai; Han, Yongming; Dällenbach, Kaspar; Canonaco, Francesco; Slowik, Jay; El Haddad, Imad; Baltensperger, Urs; Cao, Junji; Prévôt, André S. H.

    2015-04-01

    The rapid industrialization and urbanization in developing countries has led to an increase in air pollution, along a similar trajectory to that previously experienced by the developed nations. In China, particulate pollution is a serious environmental problem that is influencing air quality, regional and global climates, and human health. A quantitative understanding of these effects has proven extremely challenging due to spatial and temporal variability in the sources of aerosols and their precursors, the complexity of particle composition, and uncertainties associated with the atmospheric aging of existing particles (Pöschl 2005; Hallquist et al., 2009; Huang et al., 2014). Nowadays the average PM2.5 concentrations in China are approximately one to two orders of magnitude higher than those observed in urban areas in the US and European countries (Cao 2012). This has forced the Chinese government to announce its first national environmental standard for PM2.5 in 2012 and to make highly ambitious plans for emission control. The Chinese aim to reduce the PM2.5 concentrations by up to 25% of the 2012 levels by 2017, backed by 277 billion investments from the central government. To achieve this ambitious aim, a better understanding of the aerosol composition, sources, and atmospheric processing is required. In this study, we present the results from intensive field measurement campaigns carried out in Chinese megacities in 2013/2014. The sources of PM2.5 and the organic aerosol (OA) were investigated by applying the multi-linear engine (ME-2) receptor model (Canonaco et al., 2013) to a comprehensive dataset. Primary sources including vehicle emissions, biomass burning, coal burning, and dust-related emissions were identified and quantified. The contributions from secondary aerosol formation processes to total PM2.5 mass and OA mass were evaluated. Detailed results will be presented and discussed. References Cao, J. J. (2012) J. Earth Environ., 3, 1030

  11. Novel biogeochemical fingerprinting approaches to sediment source apportionment in catchments (Invited)

    NASA Astrophysics Data System (ADS)

    Dungait, J.; Puttock, A.; Beniston, J. W.; Brazier, R. E.; Lal, R.; Collins, A.

    2013-12-01

    Apportioning the source of organic carbon in eroding sediments is important to constrain the scale of transport processes and to assess the impact of anthropogenic activity on environmental quality. Established biogeochemical techniques are used to trace organic inputs typically derived directly or indirectly from plants into soils, sediments and water using lipid biomarkers. Recently, advances in bulk and compound specific stable 13C isotope analyses have provided novel ways of exploring the source and residence times of organic matter in soils using the natural abundance stable 13C isotope signature of C3 and C4 plant end member values. However, the application of biogeochemical source tracing technologies at the molecular level at field to catchment scales has been slow to develop because of perceived problems with dilution of molecular-scale signals. This paper describes the results of recent experiments in natural and agricultural environments in the UK (Collins et al., 2013; Dungait et al., 2013) and United States (Puttock et al., 2012; Beniston et al., submitted) that have successfully applied new biogeochemical fingerprinting techniques using stable 13C isotope approaches and complementary modelling approaches to explore the transport of particulate and sediment-bound organic carbon at a range of scales from the small plot (m2) to field (ha) and small catchment (10's ha). References Beniston et al (submitted) The effects of crop residue removal on soil erosion and macronutrient dynamics on soils under no till for 42 years. Biogeosciences Collins et al (2013) Catchment source contributions to the sediment-bound organic matter degrading salmonid spawning gravels in a lowland river, southern England. Science of the Total Environment 456-457, 181-195. Dungait et al (2013) Microbial responses to the erosional redistribution of soil organic carbon in arable fields. Soil Biology and Biochemistry 60, 195-201. Puttock et al (2012) Stable carbon isotope analysis of

  12. Source apportionment of submicron organic aerosol at an urban background and a road site in Barcelona (Spain) during SAPUSS

    NASA Astrophysics Data System (ADS)

    Alier, M.; van Drooge, B. L.; Dall'Osto, M.; Querol, X.; Grimalt, J. O.; Tauler, R.

    2013-10-01

    This study investigates the contribution of potential sources to the submicron (PM1) organic aerosol (OA) simultaneously detected at an urban background (UB) and a road site (RS) in Barcelona during the 30 days of the intensive field campaign of SAPUSS (Solving Aerosol Problems by Using Synergistic Strategies, September-October 2010). A total of 103 filters at 12 h sampling time resolution were collected at both sites. Thirty-six neutral and polar organic compounds of known emission sources and photo-chemical transformation processes were analyzed by gas chromatography-mass spectrometry (GC-MS). The concentrations of the trace chemical compounds analyzed are herein presented and discussed. Additionally, OA source apportionment was performed by multivariate curve resolution-alternating least squares (MCR-ALS) and six OA components were identified at both sites: two were of primary anthropogenic OA origin and three of secondary OA origin, while a sixth one was not clearly defined. Primary organics from emissions of local anthropogenic activities (urban primary organic aerosol, or POA Urban), mainly traffic emissions but also cigarette smoke, contributed 43% (1.5 μg OC m-3) and 18% (0.4 μg OC m-3) to OA at RS and UB, respectively. A secondary primary source - biomass burning (BBOA) - was found in all the samples (average values 7% RS; 12% UB; 0.3 μg OC m-3), but this component was substantially contributing to OA only when the sampling sites were under influence of regional air mass circulation (REG.). Three secondary organic aerosol (SOA) components (describing overall 60% of the variance) were observed in the urban ambient PM1. Products of isoprene oxidation (SOA ISO) - i.e. 2-methylglyceric acid, C5 alkene triols and 2-methyltetrols - showed the highest abundance at both sites when the city was under influence of inland air masses. The overall concentrations of SOA ISO were similar at both sites (0.4 and 0.3 μg m-3, or 16% and 7%, at UB and RS, respectively

  13. Source apportionment of submicron organic aerosol at an urban background and a road site in Barcelona, Spain

    NASA Astrophysics Data System (ADS)

    Alier, M.; van Drooge, B. L.; Dall'Osto, M.; Querol, X.; Grimalt, J. O.; Tauler, R.

    2013-04-01

    This study investigates the contribution of potential sources to the sub-micron (PM1) organic aerosol (OA) simultaneously detected at an urban background (UB) and a road site (RS) in Barcelona during the 30 days of the intensive field campaign of SAPUSS (Solving Aerosol Problems by Using Synergistic Strategies, September-October 2010). 103 filters at 12 h sampling time resolution were collected at both sites. Thirty-six neutral and polar organic compounds of known emission sources and photo-chemical transformation processes were analyzed by Gas Chromatography-Mass Spectrometry (GC-MS). The concentrations of the trace chemical compounds analyzed are herein presented and discussed. Additionally, OA source apportionment was performed by Multivariate Curve Resolution-Alternating Least Squares (MCR-ALS) and six OA components were identified at both sites: two were of primary anthropogenic OA origin, three of secondary OA origin while a sixth one was not clearly defined. Primary organics from emissions of local anthropogenic activities (Urban primary organic aerosol, Urban POA) contributed for 43% (1.5 μg OC m-3) and 18% (0.4 μg OC m-3) to OA in RS and UB, respectively. A secondary primary source - biomass burning (BBOA) - was found in all the samples (average values 7% RS; 12% UB; 0.3 μg OC m-3), but this component was substantially contributing to OA only when the sampling sites were under influence of regional air mass circulation. Three Secondary Organic Aerosol (SOA) components (describing overall 60% of the variance) were observed in the urban ambient PM1. Products of isoprene oxidation (SOA ISO), i.e. 2-methylglyceric acid, C5 alkene triols and 2-methyltetrols, showed the highest abundance at both sites when the city was under influence of inland air masses. The overall concentrations of SOA ISO were similar at both sites (0.4 and 0.3 μg m-3, 16% and 7%, at UB and RS, respectively). By contrast, a SOA biogenic component attributed to α-pinene oxidation (SOA

  14. Impacts of updated emission inventories on source apportionment of fine particle and ozone over the southeastern U.S.

    NASA Astrophysics Data System (ADS)

    Zhang, Yang; Wang, Wei; Wu, Shiang-Yuh; Wang, Kai; Minoura, Hiroaki; Wang, Zifa

    2014-05-01

    As the U.S. Environmental Protection Agency updates the National Emission Inventory (NEI), the source contributions (SC) of major source sectors to major pollutants based on source apportionment techniques should be periodically reassessed to reflect changes in SCs due to changes in emissions. This work assesses emission updates from the 1999 NEI version 2 (NEI99v2) and the 2005 NEI (NEI05) and the resulting differences in SCs using the two inventories. Large differences exist in the emissions of nitrogen oxide, formaldehyde, ammonia, terpene, and primary PM2.5 between NEI99v2 and NEI05. Differences in emissions lead to differences in model performance and source appointment. SCs of ten major source categories to fine particulate matter (PM2.5) are estimated using the Community Multiscale Air Quality modeling system with the Brute Force Method (CMAQ/BFM) andNEI05and compared with those obtained previously using CMAQ/BFM with NEI99v2. In January, compared to CMAQ/BFM (NEI99v2), CMAQ/BFM (NEI05) shows that miscellaneous areas, biomass burning, and coal combustion remain the top three contributors to PM2.5 but with different ranking and higher SCs (17.7%, 16.0%, and 14.1% for NEI05 vs. 11.8%, 13.7%, and 10.8% for NEI99v2, respectively). In July, coal combustion, miscellaneous areas, and industrial processes remain the top three with higher SCs (41.9%, 14.1%, and 8.8% for NEI05 vs.30.8%, 8.9%, and 6.9% for NEI99v2, respectively). Those changes in SCs are attributed to increased primary PM2.5 (PPM) emissions in NEI05 and increases in relative contributions of miscellaneous areas and coal combustion to the emissions of PPM, NH3, and SO2.SCs from diesel and gasoline vehicles decrease in both months, due to decreased contributions of gasoline vehicles to SO2 and NH3 emissions and those of diesel vehicles to NOx and PPM emissions. Compared with CMAQ/BFM (NEI99v2), SCs from other combustion and biomass burning are higher in Florida, due to substantial increases in

  15. Seasonal variation and source apportionment of PAHs in TSP in the atmosphere of Guiyang, Southwest China

    NASA Astrophysics Data System (ADS)

    Hu, J.; Liu, C. Q.; Zhang, G. P.; Zhang, Y. L.

    2012-11-01

    Total suspended particle (TSP) samples were collected during January to December in 2005 at urban and rural sites in Guiyang, and were analyzed for 14 particulate-phase polycyclic aromatic hydrocarbons (P-PAHs) using High Performance Liquid Chromatography (HPLC) with fluorescence detection. The total concentration of the P-PAHs ranged from 6.0-29.1 ng/m3 at monitoring sites, and 1.2-84.8 ng/m3 in and around Guiyang. P-PAHs concentration in samples collected from Guiyang possesses distinct seasonal variation with a higher concentration in winter and lower concentration in summer. PAHs with 5-ring were found to have the most distinct seasonal variation among other target PAHs. Correlations between the TSP concentration, ambient temperature (T), relative humidity (RH), and the P-PAHs concentrations were evaluated. It was found that the TSP had significant influence on the P-PAHs concentration with correlation coefficients of 0.69 (P < 0.01, n = 180). In addition, the P-PAHs concentration showed negative correlation with RH (r = - 0.28, P < 0.01, n = 180), and a moderate negative correlation with T (r = - 0.17, P < 0.05 n = 180). Diagnostic ratios and Principal Component Analysis suggest that the main pollution sources identified were coal combustion emission (52.5%), traffic gasoline (21.4%) and other miscellaneous sources (14.2%).

  16. Source Apportionment of Stack Emissions from Research and Development Facilities Using Positive Matrix Factorization

    SciTech Connect

    Ballinger, Marcel Y.; Larson, Timothy V.

    2014-08-19

    Emissions from research and development (R&D) facilities are difficult to characterize due to the wide variety of processes used, changing nature of research, and large number of chemicals. Positive matrix factorization (PMF) was applied to volatile organic compounds (VOCs) concentrations measured in the main exhaust stacks of four different R&D buildings to identify the number and composition of major contributing sources. PMF identified from 9-11 source-related factors contributing to the stack emissions depending on the building. The factors that were similar between buildings were major contributors to trichloroethylene (TCE), acetone, and ethanol emissions. Several other factors had similar profiles for two or more buildings but not for all four. One factor for each building was a combination of p/m-xylene, o-xylene and ethylbenzene. At least one factor for each building was identified that contained a broad mix of many species and constraints were used in PMF to modify the factors to resemble more closely the off-shift concentration profiles. PMF accepted the constraints with little decrease in model fit. Although the PMF model predicted the profiles of the off-shift samples, the percent of total emissions was under-predicted by the model versus the measured data.

  17. Chemical characterization of volatile organic compounds near the World Trade Center: Ambient concentrations and source apportionment

    NASA Astrophysics Data System (ADS)

    Olson, David A.; Norris, Gary A.; Seila, Robert L.; Landis, Matthew S.; Vette, Alan F.

    Concentrations of 53 volatile organic compounds (VOCs) are reported from four locations near the World Trade Center (WTC) (New York, USA) complex for canister samples collected from September 2001 through January 2002. Across the four sampling sites, mean concentrations ranged from 94.5 to 219μgm-3 for total VOCs. The highest mean concentrations for individual VOCs at any site were for ethane (18.7μgm-3), isopentane (17.1μgm-3), and m,p-xylenes (17.0μgm-3). VOC concentrations were generally highest for samples collected north and west of the WTC complex. Concentrations of total VOCs (and most individual VOCs) decreased from the period when fires were present at the WTC complex (before 19 December 2001) to the period after fires. The EPA Unmix Version 5.0 receptor model was used to assess the impact of WTC fires and recovery efforts on ambient VOC concentrations. Four factors were identified: burning of building debris, a mixed recovery/heating source, motor vehicle exhaust, and a mixed gasoline source.

  18. Source apportionment of DDTs in maricultured fish: a modeling study in South China.

    PubMed

    Fang, Shu-Ming; Bao, Lian-Jun; Yiruhan; Zeng, Eddy Y

    2016-04-01

    Fish is one of the most important nutrition sources for humanity. Contaminant exposure risk in fish farming will eventually deliver to the crowd through diet. China is the largest fish producing as well as exporting country, where mariculture plays an important role in fish production, especially in South China. Previous investigations indicated that a variety of compartments in farming areas of South China Sea were polluted by persistent organic pollutants, including DDT (dichlorodiphenyltrichloroethane) and its derivatives, some of which is designated as DDTs. In the present study, Hailing Bay and Daya Bay of Guangdong Province, China, were selected as the study sites and DDTs as the target compounds. A fish enrichment model was developed to assess the relative contributions of various pathways to the mass loadings of DDTs in the fish. Average concentrations (and concentration ranges) of DDTs in various environmental compartments of Hailing Bay and Daya Bay were included in modeling and analysis. Modeling results indicated that fish food and seawater contributed approximately the same proportions for the DDTs in maricultured fish. Antifouling paint was supposed to be the primary source of water DDTs in mariculture zone of Hailing Bay and Daya Bay, which contributed 69 % of the total DDTs to the mariculture water. We suggest that in order to protect people from consuming highly contaminated maricuture zone fish, the most effective and feasible methods are using environment-friendly antifouling paint and applying less polluted fish food in the fish reproduction process.

  19. Size distribution, mixing state and source apportionment of black carbon aerosol in London during wintertime

    NASA Astrophysics Data System (ADS)

    Liu, D.; Allan, J. D.; Young, D. E.; Coe, H.; Beddows, D.; Fleming, Z. L.; Flynn, M. J.; Gallagher, M. W.; Harrison, R. M.; Lee, J.; Prevot, A. S. H.; Taylor, J. W.; Yin, J.; Williams, P. I.; Zotter, P.

    2014-09-01

    Black carbon aerosols (BC) at a London urban site were characterised in both winter- and summertime 2012 during the Clean Air for London (ClearfLo) project. Positive matrix factorisation (PMF) factors of organic aerosol mass spectra measured by a high-resolution aerosol mass spectrometer (HR-AMS) showed traffic-dominant sources in summer but in winter the influence of additional non-traffic sources became more important, mainly from solid fuel sources (SF). Measurements using a single particle soot photometer (SP2, DMT), showed the traffic-dominant BC exhibited an almost uniform BC core size (Dc) distribution with very thin coating thickness throughout the detectable range of Dc. However, the size distribution of sf (project average mass median Dc = 149 ± 22 nm in winter, and 120 ± 6 nm in summer) and BC coating thickness varied significantly in winter. A novel methodology was developed to attribute the BC number concentrations and mass abundances from traffic (BCtr) and from SF (BCsf), by using a 2-D histogram of the particle optical properties as a function of BC core size, as measured by the SP2. The BCtr and BCsf showed distinctly different sf distributions and coating thicknesses, with BCsf displaying larger Dc and larger coating thickness compared to BCtr. BC particles from different sources were also apportioned by applying a multiple linear regression between the total BC mass and each AMS-PMF factor (BC-AMS-PMF method), and also attributed by applying the absorption spectral dependence of carbonaceous aerosols to 7-wavelength Aethalometer measurements (Aethalometer method). Air masses that originated from westerly (W), southeasterly (SE), and easterly (E) sectors showed BCsf fractions that ranged from low to high, and whose mass median Dc values were 137 ± 10 nm, 143 ± 11 nm and 169 ± 29 nm, respectively. The corresponding bulk relative coating thickness of BC (coated particle size/BC core - Dp/Dc) for these same sectors was 1.28 ± 0.07, 1.45 ± 0

  20. Size distribution, mixing state and source apportionments of black carbon aerosols in London during winter time

    NASA Astrophysics Data System (ADS)

    Liu, D.; Allan, J. D.; Young, D. E.; Coe, H.; Beddows, D.; Fleming, Z. L.; Flynn, M. J.; Gallagher, M. W.; Harrison, R. M.; Lee, J.; Prevot, A. S. H.; Taylor, J. W.; Yin, J.; Williams, P. I.; Zotter, P.

    2014-06-01

    Black carbon aerosols (BC) at a London urban site were characterized in both winter and summer time 2012 during the Clean Air for London (ClearfLo) project. Positive matrix factorization (PMF) factors of organic aerosol mass spectra measured by a high resolution aerosol mass spectrometer (HR-AMS) showed traffic-dominant sources in summer but in winter the influence of additional non-traffic sources became more important, mainly from solid fuel sources (SF). Measurements using a single particle soot photometer (SP2, DMT), showed the traffic-dominant BC exhibited an almost uniform BC core size (Dc) distribution with very thin coating thickness throughout the detectable range of Dc. However the size distribution of Dc (project average mass median Dc = 149 ± 22 nm in winter, and 120 ± 6 nm in summer) and BC coating thickness varied significantly in winter. A novel methodology was developed to attribute the BC number concentrations and mass abundances from traffic (BCtr) and from SF (BCsf), by using a 2-D histogram of the particle optical properties as a function of BC core size, as measured by the SP2. The BCtr and BCsf showed distinctly different Dc distributions and coating thicknesses, with BCsf displaying larger Dc and larger coating thickness compared to BCtr. BC particles from different sources were also apportioned by applying a multiple linear regression between the total BC mass and each AMS-PMF factor (BC-AMS-PMF method), and also attributed by applying the absorption spectral dependence of carbonaceous aerosols to 7-wavelength Aethalometer measurements (Aethalometer method). Air masses that originated from westerly (W), southeasterly (SE), or easterly (E) sectors showed BCsf fractions that ranged from low to high, and whose mass median Dc values were 137 ± 10 nm, 143 ± 11 nm, and 169 ± 29 nm respectively. The corresponding bulk relative coating thickness of BC (coated particle size / BC core - Dp / Dc) for these same sectors was 1.28 ± 0.07, 1.45 ± 0

  1. Source apportionment and air quality impact assessment studies in Beijing/China

    NASA Astrophysics Data System (ADS)

    Suppan, P.; Schrader, S.; Shen, R.; Ling, H.; Schäfer, K.; Norra, S.; Vogel, B.; Wang, Y.

    2012-04-01

    More than 15 million people in the greater area of Beijing are still suffering from severe air pollution levels caused by sources within the city itself but also from external impacts like severe dust storms and long range advection from the southern and central part of China. Within this context particulate matter (PM) is the major air pollutant in the greater area of Beijing (Garland et al., 2009). PM did not serve only as lead substance for air quality levels and therefore for adverse health impact effects but also for a strong influence on the climate system by changing e.g. the radiative balance. Investigations on emission reductions during the Olympic Summer Games in 2008 have caused a strong reduction on coarser particles (PM10) but not on smaller particles (PM2.5). In order to discriminate the composition of the particulate matter levels, the different behavior of coarser and smaller particles investigations on source attribution, particle characteristics and external impacts on the PM levels of the city of Beijing by measurements and modeling are performed: Examples of long term measurements of PM2.5 filter sampling in 2005 with the objectives of detailed chemical (source attribution, carbon fraction, organic speciation and inorganic composition) and isotopic analyses as well as toxicological assessment in cooperation with several institutions (Karlsruhe Institute of Technology (IfGG/IMG), Helmholtz Zentrum München (HMGU), University Rostock (UR), Chinese University of Mining and Technology Beijing, CUMTB) will be discussed. Further experimental studies include the operation of remote sensing systems to determine continuously the MLH (by a ceilometer) and gaseous air pollutants near the ground (by DOAS systems) as well as at the 320 m measurement tower (adhesive plates at different heights for passive particle collection) in cooperation with the Institute of Atmospheric Physics (IAP) of the Chinese Academy of Sciences (CAS). The influence of the MLH on

  2. Levels and source apportionment of volatile organic compounds in southwestern area of Mexico City.

    PubMed

    Rodolfo Sosa, E; Humberto Bravo, A; Violeta Mugica, A; Pablo Sanchez, A; Emma Bueno, L; Krupa, Sagar

    2009-03-01

    Thirteen volatile organic compounds (VOCs) were quantified at three sites in southwestern Mexico City from July 2000 to February 2001. High concentrations of different VOCs were found at a Gasoline refueling station (GS), a Condominium area (CA), and at the University Center for Atmospheric Sciences (CAS). The most abundant VOCs at CA and CAS were propane, n-butane, toluene, acetylene and pentane. In comparison, at GS the most abundant were toluene, pentane, propane, n-butane, and acetylene. Benzene, a known carcinogenic compound had average levels of 28, 35 and 250ppbC at CAS, CA, and GS respectively. The main contributing sources of the measured VOCs at CA and CAS were the handling and management of LP (Liquid Propane) gas, vehicle exhaust, asphalt works, and use of solvents. At GS almost all of the VOCs came from vehicle exhaust and fuel evaporation, although components of LP gas were also present. Based on the overall results possible abatement strategies are discussed.

  3. Source apportionment of size segregated fine/ultrafine particle by PMF in Beijing

    NASA Astrophysics Data System (ADS)

    Tan, Ji-hua; Duan, Jing-chun; Chai, Fa-he; He, Ke-bin; Hao, Ji-Ming

    2014-03-01

    Considering the adverse health effects to human body, the number concentration of atmospheric PM (particulate material) is more important than the mass concentration. CO, NO, NO2, SO2 and number concentrations of PM were obtained from a remote site (Miyun), a roadside site (North Fourth Ring Road) and an urban residential site (Tsinghua University) in Beijing in winter. The size distribution and the possible sources of number concentrations were examined using EPA PMF (positive matrix factorization) model. A data set of totally 9610 of number concentration with the size range of 0.028 μm to 0.948 μm was included in the PMF analysis. The highest total particle number, mass and area of fine particles concentrations were observed at the North Fourth Ring Road site and the lowest were observed at Miyun site. Four factors were identified at Miyun site, as Factor 1 and Factor 4 may be related to long distance transportation, and Factor 2 and Factor 3 may be assigned as coal combustion and locomotive emission nearby, respectively; three factors were identified at North Fourth Ring Road, of which Factor 1 and Factor 3 are traffic related and Factor 2 may be coal combustion related. Compared with Factor 1, the contributions of Factor 3 to NOx and SO2 were 4-5 times higher. Additionally, Factor 3 was also a major contributor to CO. It suggested that Factor 1 and Factor 3 had the same source emission of motor vehicle, but different engine types, fuel types or exhaust treatments. Three factors were identified at Tsinghua site, as Factor 1 may come from aging vehicle emission, and Factor 2 and Factor 3 may be coal combustion related.

  4. PM source apportionment for short-term cardiac function changes in ApoE-/- mice.

    PubMed

    Lippmann, Morton; Hwang, Jiang-Shiang; Maciejczyk, Polina; Chen, Lung-Chi

    2005-11-01

    Daily rates of cardiovascular mortality and morbidity are have been associated with daily variations in fine particulate matter (aerodynamic diameter < or = 2.5 microm, PM2.5), but little is known about the influences of the individual source-related PM2.5 categories or the temporal lags for the effects. We investigated heart rate (HR) and HR variability (HRV) data collected during a 5-month study involving 6 hr/day, 5 day/week exposures of normal (C57) mice and a murine model for atherosclerotic disease (ApoE-/-) in Sterling Forest (Tuxedo, New York, USA). The mice were exposed to concentrated ambient particles (PM2.5 concentrated 10-fold, producing an average of 113 microg/m3). Daily 6-hr PM2.5 air samples were analyzed by X-ray fluorescence, permitting attribution to major PM source categories [secondary sulfate (SS), resuspended soil (RS), residual oil (RO) combustion, and other, largely due to motor vehicle traffic]. We examined associations between these PM2.5 components and both HR and HRV for three different daily time periods: during exposure, the afternoon after exposure, and late at night. For HR there were significant transient associations for RS during exposure, and for SS in the afternoon after exposure. For HRV, there were comparable associations with RO in the afternoon after exposure and for both SS and RS late at night. The biologic bases for these associations and their temporal lags are not known but may be related to the differential solubility of the biologically active PM components at the respiratory epithelia and their access to cells that release mediators that reach the cardiovascular system. Clearly, further research to elucidate the underlying processes is needed.

  5. Volatile organic compounds in Tijuana during the Cal-Mex 2010 campaign: Measurements and source apportionment

    NASA Astrophysics Data System (ADS)

    Zheng, Jun; Garzón, Jessica P.; Huertas, María E.; Zhang, Renyi; Levy, Misti; Ma, Yan; Huertas, José I.; Jardón, Ricardo T.; Ruíz, Luis G.; Tan, Haobo; Molina, Luisa T.

    2013-05-01

    As part of the Cal-Mex 2010 air quality study, a proton transfer reaction-mass spectrometer (PTR-MS) was deployed at the San Diego-Tijuana border area to measure volatile organic compounds (VOCs) from 15 May to 30 June 2010. The major VOCs identified during the study included oxygenated VOCs (e.g., methanol, acetaldehyde, acetone, and methyl ethyl ketone) and aromatics (e.g., benzene, toluene, C8- and C9-aromatics). Biogenic VOCs (e.g., isoprene) were scarce in this region because of the lack of vegetation in this arid area. Using an U.S. EPA positive matrix factorization model, VOCs together with other trace gases (NOx, NOz and SO2) observed in this border region were attributed to four types of sources, i.e., local industrial solvent usage (58% in ppbC), gasoline vehicle exhaust (19% in ppbC), diesel vehicle exhaust (14% in ppbC), and aged plume (9% in ppbC) due to regional background and/or long-range transport. Diesel vehicle emission contributed to 87% of SO2 and 75% of NOx, and aged plume contributed to 92% of NOz. An independent conditional probability function analysis of VOCs, wind direction, and wind speed indicated that the industrial source did not show a significant tendency with wind direction. Both gasoline and diesel engine emissions were associated with air masses passing through two busy cross-border ports. Aged plumes were strongly associated with NW wind, which likely brought in aged air masses from the populated San Diego area.

  6. Non-methane hydrocarbons source apportionment at different sites in Mexico City during 2002-2003

    NASA Astrophysics Data System (ADS)

    Vega, E.; Sanchez, G.; Molina, L.

    2007-09-01

    The atmospheric concentrations of a variety of non-methane hydrocarbons (NMHC) collected at different sites, representing urban and rural environments within Mexico City Metropolitan Area (MCMA) during 1997, 2002 and 2003 field campaigns, were compared and used as an input for the Chemical Mass Balance (CMB) receptor model to determine the source contribution of NMHC to the atmosphere. A common feature at all the locations was the dominance of alkenes (59%), aromatics (16%) and olefins (9%) in the average NMHC burden. At the urban sites the interquartile range of NMHC concentrations showed stabilization over this period with a slight increase in the concentrations of propane and butanes in the southwest site of the MCMA in 2003 due to the increased use of liquefied petroleum gas (LPG). The receptor model CMB version 8.0 was used to apportion the NMHC sources at six locations within the MCMA, representing the heavily industrialized, commercial, residential and rural areas. For the 2003 field campaign, the contribution of vehicular emissions dominated the NMHC concentrations (19.7%±7.1% for gasoline vehicles and 35.4%±17.5% for diesel vehicles) followed by the emissions of marketing and handling of LPG (29.9%±8.0%). The NMHC concentrations showed a weekly cycle with the highest levels towards the end of the week and lowest at weekend and beginning of the week, suggesting that both emissions and accumulations process play a key role in building up NMHC levels. The toluene to benzene ratio was used to determine photochemical ageing of the air samples during the 2003 field campaign. The database was divided into periods with similar wind circulation pattern; the results suggest that ageing process within the MCMA is generally suppressed by the amount of fresh emissions.

  7. Fine particulate matter and visibility in the Lake Tahoe Basin: chemical characterization, trends, and source apportionment.

    PubMed

    Green, Mark C; Chen, L W Antony; DuBois, David W; Molenar, John V

    2012-08-01

    Speciated PM2.5 (particulate matter with an aerodynamic diametersources at both sites with increasing importance over time; (2) low combustion efficiency burning accounts for most of the biomass burning contribution; (3) road dust and traffic contributions were much higher at SOLA than at BLIS; and (4) industrial combustion and salting were minor sources.

  8. Distribution and source apportionment studies of heavy metals in soil of cotton/wheat fields.

    PubMed

    Rafique, Nazia; Tariq, Saadia R

    2016-05-01

    Heavy metals enriched agricultural soils have been the subject of great concern because these metals have potential to be transferred to the soil solution and afterward accumulated in food chain. To study the trace metal persistence in crop soil, 90 representative soil samples were collected and analyzed for heavy metal (As, Cd, Cu, Fe, Mn, Ni, Pb, and Zn) and anions (chloride, nitrates, phosphates and sulfates). Cluster and factor analysis techniques were used for the source identification of these excessive heavy metal levels and ecological risk was determined with potential ecological risk assessment. The degree of enrichment of eight studied heavy metals in comparison with the corresponding background levels decreased in order: Cd > Pb > Fe > Ni > Mn > As > Cu ~ Zn. Arsenic and cadmium exhibited 1.30- and 1.64-fold exceeded levels than threshold limits set by National environment quality standards, respectively. Cd in cotton field's soil may lead to higher potential risk than other heavy metals. On overall basis, the cumulative mean potential ecological risk for the district (207.75) corresponded to moderate risk level with higher contributions from As and Pb especially from Cd. Cadmium formed strong positive correlation with phosphate content of soil at p < 0.01. Cluster analysis indicated that Cluster 1 (extremely polluted) probably originated from anthropogenic inputs of phosphate fertilizer and past usage of arsenical pesticides.

  9. Application of receptor models on water quality data in source apportionment in Kuantan River Basin

    PubMed Central

    2012-01-01

    Recent techniques in the management of surface river water have been expanding the demand on the method that can provide more representative of multivariate data set. A proper technique of the architecture of artificial neural network (ANN) model and multiple linear regression (MLR) provides an advance tool for surface water modeling and forecasting. The development of receptor model was applied in order to determine the major sources of pollutants at Kuantan River Basin, Malaysia. Thirteen water quality parameters were used in principal component analysis (PCA) and new variables of fertilizer waste, surface runoff, anthropogenic input, chemical and mineral changes and erosion are successfully developed for modeling purposes. Two models were compared in terms of efficiency and goodness-of-fit for water quality index (WQI) prediction. The results show that APCS-ANN model gives better performance with high R2 value (0.9680) and small root mean square error (RMSE) value (2.6409) compared to APCS-MLR model. Meanwhile from the sensitivity analysis, fertilizer waste acts as the dominant pollutant contributor (59.82%) to the basin studied followed by anthropogenic input (22.48%), surface runoff (13.42%), erosion (2.33%) and lastly chemical and mineral changes (1.95%). Thus, this study concluded that receptor modeling of APCS-ANN can be used to solve various constraints in environmental problem that exist between water distribution variables toward appropriate water quality management. PMID:23369363

  10. Source apportionment of sedimentary hydrocarbons in the Segara Anakan Nature Reserve, Indonesia.

    PubMed

    Syakti, Agung Dhamar; Hidayati, Nuning Vita; Hilmi, Endang; Piram, Anne; Doumenq, Pierre

    2013-09-15

    The study aimed to determine the spatial distribution of n-alkanes and polycyclic aromatic hydrocarbons (PAHs) in surface sediments of the Segara Anakan nature reserve and their potential origins using gas chromatography-mass spectrometry. Total alkane concentrations ranged from 3755 to 129,027 μg kg(-1), and the concentrations of 16 PAHs ranged from 375 to 29,517 μg kg(-1). The ratios of specific n-alkanes (e.g., CPI(24-34), WaxC(n), and Paq), including a new proposed index, terrestrial-marine discriminant (TMD), as well as the ratios of selected PAHs (e.g., Ant/∑178, Fl/∑202, BaAnt/∑228, and IPyr/∑276), showed that the sources of hydrocarbons in the sediments were generally biogenic, including both terrigenous and marine, with an anthropogenic pyrolytic contribution (petrogenic and biogenic combustion). For the environmental risk assessment, a sediment quality guideline (SQGs) comparison indicated that the station risk levels ranged from low to medium-low, except for R6, which has a greater impact on the ecological risk for marine organisms.

  11. Hydrophobic Organic Compounds in Hydraulic Fracturing Flowback Waters: Identification and Source Apportionment

    NASA Astrophysics Data System (ADS)

    Plata, D.; Shregglman, K.; Elsner, M.; Getzinger, G.; Ferguson, L.; Drollette, B.; Karatum, O.; Nelson, R. K.; Reddy, C. M.

    2014-12-01

    Current hydraulic fracturing technologies rely on organic chemicals to serve multiple critical functions, including corrosion inhibition, in situ gel formation, and friction reduction. While industrial users have disclosed several hundreds of compound and mixture identities, it is unclear which of these are used and where, in what proportion, and with what frequency. Furthermore, while flowback and production waters contain both fracturing additive and geogenic compounds, they may contain potential reaction byproducts as well. Here, we identified several hundred organic compounds present in six hydraulic fracturing flowback waters over the Fayetteville shale. Identifications were made via non-target analysis using two-dimensional gas chromatography with time of flight mass spectrometry for hydrophobic organic compounds and liquid chromatography- orbitrap mass spectrometry. Compound identities were confirmed using purchased standards when available. Using the SkyTruth database and the Waxman list of disclosed compounds, we assigned compounds as either fracturing-fluid-derived or geogenic (or both), or a putative transformation products thereof. Several unreported halogenated compounds were detected, including chlorinated, brominated, and iodated species that have no known natural sources. Control studies indicated that these could not be formed under typical laboratory or field storage conditions, suggesting that halogenation reactions may give rise to novel compounds in the subsurface, presumably via reaction between fracturing fluid additives and shale-derived brines. Further, the six samples were strikingly heterogeneous, reflecting the diversity in fracturing fluid composition and flowback handling procedures at the time of the study.

  12. Spatial Distribution, Sources Apportionment and Health Risk of Metals in Topsoil in Beijing, China

    PubMed Central

    Sun, Chunyuan; Zhao, Wenji; Zhang, Qianzhong; Yu, Xue; Zheng, Xiaoxia; Zhao, Jiayin; Lv, Ming

    2016-01-01

    In order to acquire the pollution feature and regularities of distribution of metals in the topsoil within the sixth ring road in Beijing, a total of 46 soil samples were collected, and the concentrations of twelve elements (Nickel, Ni, Lithium, Li, Vanadium, V, Cobalt, Co, Barium, Ba, Strontium, Sr, Chrome, Cr, Molybdenum, Mo, Copper, Cu, Cadmium, Cd, Zinc, Zn, Lead, Pb) were analyzed. Geostatistics and multivariate statistics were conducted to identify spatial distribution characteristics and sources. In addition, the health risk of the analyzed heavy metals to humans (adult) was evaluated by an U.S. Environmental Protection Agency health risk assessment model. The results indicate that these metals have notable variation in spatial scale. The concentration of Cr was high in the west and low in the east, while that of Mo was high in the north and low in the south. High concentrations of Cu, Cd, Zn, and Pb were found in the central part of the city. The average enrichment degree of Cd is 5.94, reaching the standard of significant enrichment. The accumulation of Cr, Mo, Cu, Cd, Zn, and Pb is influenced by anthropogenic activity, including vehicle exhaustion, coal burning, and industrial processes. Health risk assessment shows that both non-carcinogenic and carcinogenic risks of selected heavy metals are within the safety standard and the rank of the carcinogenic risk of the four heavy metals is Cr > Co > Ni > Cd. PMID:27447657

  13. Spatial distribution and source apportionment of PAHs in marine surface sediments of Prydz Bay, East Antarctica.

    PubMed

    Xue, Rui; Chen, Ling; Lu, Zhibo; Wang, Juan; Yang, Haizhen; Zhang, Jie; Cai, Minghong

    2016-12-01

    This paper reports the concentrations of polycyclic aromatic hydrocarbons (PAHs) in marine sediments sampled from Prydz Bay, East Antarctica. Total PAH concentrations ranged from 12.95 to 30.93 ng/g, with a mean of 17.99 ± 5.57 ng/g. Two- and three-ring PAHs were the most abundant compounds found at the majority of the sampling stations of Prydz Bay. Long-range atmospheric transportation was found to play an important role in determining the spatial distribution of PAHs in the sediments sampled here. However, transport by ocean currents and release from melting glaciers were also found to influence PAH distributions in the sediments of East Antarctica. The vertical migration of PAHs in sediments showed a decreasing trend with depth, with higher concentrations in the relatively shallow-water regions (<500 m) found on the Fram and Four Ladies banks compared with those of the intermediate-depth (500-1000 m) and deep-water regions (>1000 m) of the Amery Basin and associated Canyons, respectively. A Pearson correlation analysis between PAH concentrations and sediment parameters demonstrated that PAHs has poor correlations with grain size, but has positive correlation with total organic carbon, indicated complex processing during transfer to remote environments. The results of qualitative and quantitative analyses indicate that the PAHs sampled here were derived mainly from a mixture of biomass combustion, traffic emissions, and petrogenic sources.

  14. [Source apportionment of VOCs in the northern suburb of Nanjing in summer].

    PubMed

    Yang, Hui; Zhu, Bin; Gao, Jin-Hui; Li, Yong-Yu; Xia, Li

    2013-12-01

    Hourly concentrations of ambient volatile organic compounds (VOCs) were sampled in August 2012 in the northern suburb of Nanjing. Emissions of VOCs were analyzed by using PMF (positive matrix factorization) and CPF (conditional probability function). The hourly average mixing ratio of the TVOCs in summer was (33.84 +/- 27.77) x 10(-9), with a bimodal diurnal variation trend. 49.3% of the TVOCs were alkanes, 24.4% were alkenes, 18.5% were aromatics and 7.81% were acetylene. Five sources were identified as summer major contributors to ambient VOCs concentrations by PMF. 33.1% of the total VOCs was attributed to vehicle related emissions, 25.8% to fuel evaporation, 23.2% to industrial emissions, 8.1% to solvent evaporation and 9.7% to plant emissions. For alkanes, vehicle emissions, industrial emissions, fuel and solvent evaporation accounted for 23.7%, 35.3%, 31.3% and 2%, respectively. For alkenes, fuel evaporation accounted for 41.1% , industrial emissions for 18.4%, and vehicle emission for 24.3%. Vehicle emission was the major contributor to aromatics, accounting for 49.2%, followed by solvent evaporation, which accounted for 30.8%.

  15. Source apportionment of VOCs and the contribution to photochemical ozone formation during summer in the typical industrial area in the Yangtze River Delta, China

    NASA Astrophysics Data System (ADS)

    Shao, Ping; An, Junlin; Xin, Jinyuan; Wu, Fangkun; Wang, Junxiu; Ji, Dongsheng; Wang, Yuesi

    2016-07-01

    Volatile organic compounds (VOCs) were continuously observated in a northern suburb of Nanjing, a typical industrial area in the Yangtze River Delta, in a summer observation period from 15th May to 31st August 2013. The average concentration of total VOCs was (34.40 ± 25.20) ppbv, including alkanes (14.98 ± 12.72) ppbv, alkenes (7.35 ± 5.93) ppbv, aromatics (9.06 ± 6.64) ppbv and alkynes (3.02 ± 2.01) ppbv, respectively. Source apportionment via Positive Matrix Factorization was conducted, and six major sources of VOCs were identified. The industry-related sources, including industrial emissions and industrial solvent usage, occupied the highest proportion, accounting for about 51.26% of the VOCs. Vehicular emissions occupied the second highest proportion, accounting for about 34.08%. The rest accounted for about 14.66%, including vegetation emission and liquefied petroleum gas/natural gas usage. Contributions of VOCs to photochemical O3 formation were evaluated by the application of a detailed chemical mechanism model (NCAR MM). Alkenes were the dominant contributors to the O3 photochemical production, followed by aromatics and alkanes. Alkynes had a very small impact on photochemical O3 formation. Based on the outcomes of the source apportionment, a sensitivity analysis of relative O3 reduction efficiency (RORE), under different source removal regimes such as using the reduction of VOCs from 10% to 100% as input, was conducted. The RORE was the highest (~ 20%-40%) when the VOCs from solvent-related sources decreased by 40%. The highest RORE values for vegetation emissions, industrial emissions, vehicle exhaust, and LPG/NG usage were presented in the scenarios of 50%, 80%, 40% and 40%, respectively.

  16. Source apportionment of lead in the blood of women of reproductive age living near tailings in Taxco, Guerrero, Mexico: An isotopic study.

    PubMed

    Vázquez Bahéna, Analine Berenice; Talavera Mendoza, Oscar; Moreno Godínez, Ma Elena; Salgado Souto, Sergio Adrián; Ruiz, Joaquín; Huerta Beristain, Gerardo

    2017-04-01

    The concentration and isotopic composition of lead in the blood of forty seven women of reproductive age (15-45y) exposed to multiple sources in two rural communities of the mining region of Taxco, Guerrero in southern Mexico were determined in order to identify specific contributing sources and their apportionment and to trace probable ingestion pathways. Our data indicate that >36% of the studied women have blood lead concentrations above 10μgdL(-1) and up to 87% above 5μgdL(-1). Tailings contain between 2128 and 5988mgkg(-1) of lead and represent the most conspicuous source in the area. Lead contents in indoor dust are largely variable (21.7-987mgkg(-1)) but only 15% of samples are above the Mexican Regulatory Guideline for urban soils (400mgkg(-1)). By contrast, 85% of glazed containers (range: 0.026-68.6mgkg(-1)) used for cooking and food storage are above the maximum 2mgL(-1) of soluble lead established in the Mexican Guideline. The isotopic composition indicates that lead in the blood of 95% of the studied women can be modeled in terms of a mixing system between local ores (and derivatives), glazed pottery and Morelos bedrock, end-members, with the two former being largely the most important contributors. Only one sample shows influence of indoor paints. Indoor dust is dominated by ores and derivatives but some samples show evidence of contribution from a less radiogenic source very likely represented by interior paints. This study supports the application of lead isotopic ratios to identify potential sources and their apportionment in humans exposed to multiple sources of lead from both, natural and anthropogenic origin.

  17. Spatio-temporal patterns and source apportionment of pollution in Qiantang River (China) using neural-based modeling and multivariate statistical techniques

    NASA Astrophysics Data System (ADS)

    Su, Shiliang; Zhi, Junjun; Lou, Liping; Huang, Fang; Chen, Xia; Wu, Jiaping

    Characterizing the spatio-temporal patterns and apportioning the pollution sources of water bodies are important for the management and protection of water resources. The main objective of this study is to describe the dynamics of water quality and provide references for improving river pollution control practices. Comprehensive application of neural-based modeling and different multivariate methods was used to evaluate the spatio-temporal patterns and source apportionment of pollution in Qiantang River, China. Measurement data were obtained and pretreated for 13 variables from 41 monitoring sites for the period of 2001-2004. A self-organizing map classified the 41 monitoring sites into three groups (Group A, B and C), representing different pollution characteristics. Four significant parameters (dissolved oxygen, biochemical oxygen demand, total phosphorus and total lead) were identified by discriminant analysis for distinguishing variations of different years, with about 80% correct assignment for temporal variation. Rotated principal component analysis (PCA) identified four potential pollution sources for Group A (domestic sewage and agricultural pollution, industrial wastewater pollution, mineral weathering, vehicle exhaust and sand mining), five for Group B (heavy metal pollution, agricultural runoff, vehicle exhaust and sand mining, mineral weathering, chemical plants discharge) and another five for Group C (vehicle exhaust and sand mining, chemical plants discharge, soil weathering, biochemical pollution, mineral weathering). The identified potential pollution sources explained 75.6% of the total variances for Group A, 75.0% for Group B and 80.0% for Group C, respectively. Receptor-based source apportionment was applied to further estimate source contributions for each pollution variable in the three groups, which facilitated and supported the PCA results. These results could assist managers to develop optimal strategies and determine priorities for river

  18. Chemical characterization of fine particulate matter in Changzhou, China, and source apportionment with offline aerosol mass spectrometry

    NASA Astrophysics Data System (ADS)

    Ye, Zhaolian; Liu, Jiashu; Gu, Aijun; Feng, Feifei; Liu, Yuhai; Bi, Chenglu; Xu, Jianzhong; Li, Ling; Chen, Hui; Chen, Yanfang; Dai, Liang; Zhou, Quanfa; Ge, Xinlei

    2017-02-01

    matter-to-organic carbon (OM / OC) ratios of 0.54, 1.69, 0.11, and 1.99, respectively. Source apportionment of WSOA further identified two secondary OA (SOA) factors (a less oxidized and a more oxidized oxygenated OA) and two primary OA (POA) factors (a nitrogen-enriched hydrocarbon-like traffic OA and a local primary OA likely including species from cooking, coal combustion, etc.). On average, the POA contribution outweighed SOA (55 % vs. 45 %), indicating the important role of local anthropogenic emissions in the aerosol pollution in Changzhou. Our measurement also shows the abundance of organic nitrogen species in WSOA, and the source analyses suggest these species are likely associated with traffic emissions, which warrants more investigations on PM samples from other locations.

  19. Characteristics and source apportionment of organic matter in PM(2.5) from cities in different climatic zones of China

    NASA Astrophysics Data System (ADS)

    Feng, Jialiang

    For the first time, the dependency of the characteristics of organic matter in PM2.5 on geographical and climatic zones in three metropolitan cities of China was studied. Seasonal samples were collected at suburban and urban sites in Beijing, Shanghai and Guangzhou in 2002 and 2003. To further support the above study, seasonal samples were also collected at Changdao Island, a remote island, in Bohai Sea/Yellow Sea. Concentrations of organic carbon (OC), elemental carbon (EC), water-soluble organic carbon (WSOC), and solvent-extractable organic compounds (SEOC) were analyzed. The characteristics of the n-alkanes, polycyclic aromatic hydrocarbons, n-fatty acids, n-alkanols and molecular markers such as triterpanes were determined and used for source identification. Source apportionment was complemented by Chemical Mass Balance (CMB) modeling using the measured organic species as tracers. The impact of wind speed and wind direction on air quality was studied by back trajectory calculations and analysis. In general, traffic emissions were the largest contributors of OC followed by coal burning, kitchen emissions, vegetative detritus and biomass burning. However, in the space-heating season in Northern China, coal burning was the most important contributor of OC in the suburban areas of Beijing and at Changdao. Beijing had the highest concentration of organic aerosol followed by Guangzhou and Shanghai, while seasonal variation was in reverse order. Dispersion conditions determined by local topographies and meteorology were responsible for this trend. Contrary to common understanding, pollutant concentrations at the suburban sites were higher than the urban sites in all three cities. The main reason was the rapid urbanization of the suburban areas in the immediate vicinity of urban centers since China opened up for economic development, in addition, large numbers of manufacturing plants were relocated from the cities to the countryside in an attempt to clean up the urban

  20. Source apportionment of PM2.5 at multiple Northwest U.S. sites: Assessing regional winter wood smoke impacts from residential wood combustion

    NASA Astrophysics Data System (ADS)

    Kotchenruther, Robert A.

    2016-10-01

    Wood smoke from residential wood combustion is a significant source of elevated PM2.5 in many communities across the Northwest U.S. Accurate representation of residential wood combustion in source-oriented regional scale air quality models is challenging because of multiple uncertainties. As an alternative to source-oriented source apportionment, this work provides, through receptor-oriented source apportionment, an assessment of winter residential wood combustion impacts at multiple Northwest U.S. locations. Source apportionment was performed on chemically speciated PM2.5 from 19 monitoring sites using the Positive Matrix Factorization (PMF) receptor model. Each site was modeled independently, but a common data preparation and modeling protocol was used so that results were as comparable as possible across sites. Model solutions had from 4 to 8 PMF factors, depending on the site. PMF factors at each site were associated with a source classification (e.g., primary wood smoke), a dominant chemical composition (e.g., ammonium nitrate), or were some mixture. 15 different sources or chemical compositions were identified as contributing to PM2.5 across the 19 sites. The 6 most common were; aged wood smoke and secondary organic carbon, motor vehicles, primary wood smoke, ammonium nitrate, ammonium sulfate, and fugitive dust. Wood smoke was identified at every site, with both aged and primary wood smoke identified at most sites. Wood smoke contributions to PM2.5 were averaged for the two winter months of December and January, the months when wood smoke in the Northwest U.S. is mainly from residential wood combustion. The total contribution of residential wood combustion, that from primary plus aged smoke, ranged from 11.4% to 92.7% of average December and January PM2.5 depending on the site, with the highest percent contributions occurring in smaller towns that have fewer expected sources of winter PM2.5. Receptor modeling at multiple sites, such as that conducted in this

  1. [Source apportionment of nitrogen and phosphorus from cropping non-point source pollution in Nansi Lake basin].

    PubMed

    Liu, Jing; Lu, Feng; Yang, Yan-Zhao; Xu, Na; Wang, Tian-Ni

    2012-09-01

    Field runoff pools were used to collect the field surface runoff samples of different cropping systems in Nansi Lake region, and different forms of nitrogen (N) and phosphorus (P) data were analyzed. The source profiles of N and P in different cropping systems were also obtained by summarizing the experimental data measured in the current study. Samples were also collected from the 11 main rivers of Nansi Lake basin and the concentrations of N and P were determined. Principle component analysis (PCA) was applied to obtain cropping non-point pollution sources of N and P. The result showed that three types of N and P contamination sources were apportioned in Nansi Lake basin, explaining 95.275% of the total variance. The first source was from field surface runoff of wheat-maize rotation with a wide pollution range and a larger contribution, and it contributed 50. 220% of the total contamination burden; the second type of N and P source was the water runoff pollution from garlic-maize rotation, were 25.119% contribution; the third source was the surface runoff from wheat-rice rotation, and it contributed 19.937%.

  2. Source apportionment of airborne particulate matter in Southeast Texas using a source-oriented 3D air quality model

    NASA Astrophysics Data System (ADS)

    Zhang, Hongliang; Ying, Qi

    2010-09-01

    A nested version of the source-oriented externally mixed UCD/CIT model was developed to study the source contributions to airborne particulate matter (PM) during a two-week long air quality episode during the Texas 2000 Air Quality Study (TexAQS 2000). Contributions to primary PM and secondary ammonium sulfate in the Houston-Galveston Bay (HGB) and Beaumont-Port Arthur (BPA) areas were determined. The predicted 24-h elemental carbon (EC), organic compounds (OC), sulfate, ammonium ion and primary PM 2.5 mass are in good agreement with filter-based observations. Predicted concentrations of hourly sulfate, ammonium ion, and primary OC from diesel and gasoline engines and biomass burning organic aerosol (BBOA) at La Porte, Texas agree well with measurements from an Aerodyne Aerosol Mass Spectrometer (AMS). The UCD/CIT model predicts that EC is mainly from diesel engines and majority of the primary OC is from internal combustion engines and industrial sources. Open burning contributes large fractions of EC, OC and primary PM 2.5 mass. Road dust, internal combustion engines and industries are the major sources of primary PM 2.5. Wildfire dominates the contributions to all primary PM components in areas near the fires. The predicted source contributions to primary PM are in general agreement with results from a chemical mass balance (CMB) model. Discrepancy between the two models suggests that further investigations on the industrial PM emissions are necessary. Secondary ammonium sulfate accounts for the majority of the secondary inorganic PM. Over 80% of the secondary sulfate in the 4 km domain is produced in upwind areas. Coal combustion is the largest source of sulfate. Ammonium ion is mainly from agriculture sources and contributions from gasoline vehicles are significant in urban areas.

  3. Chemical characterization of ambient particulate matter near the World Trade Center: Source apportionment using organic and inorganic source markers

    NASA Astrophysics Data System (ADS)

    Olson, David A.; Norris, Gary A.

    Concentrations of alkanes (C20-C35), 14 polycyclic aromatic hydrocarbons (PAHs) and PAH ketones, and three hopanes are reported from four locations near the World Trade Center (WTC) (three of the locations within 300 m of the debris pile). The highest concentrations of individual PAHs across the four locations were for fluoranthene (10.3 ng/m 3 at site W), pyrene (8.7 ng/m 3 at site W), and chrysene (6.2 ng/m 3 at site W). The EPA Unmix Version 6.0 receptor model was used to estimate the impact of WTC fires and recovery efforts on ambient PM 2.5 concentrations. Five factors were identified: open burning of building debris, smoldering fires from building debris, a mixed recovery source, a sulfate/debris removal source, and motor vehicle exhaust.

  4. Use of synthetic data to evaluate positive matrix factorization as a source apportionment tool for PM2.5 exposure data.

    PubMed

    Brinkman, Gregory; Vance, Gary; Hannigan, Michael P; Milford, Jana B

    2006-03-15

    Positive matrix factorization (PMF) was applied to synthetic datasets that simulate personal exposures to airborne PM2.5 from 12 sources. Three differentfilter analysis scenarios using different analytical chemistry techniques were considered. The full suite scenario quantified elemental carbon, organic carbon, inorganic ions, trace elements, and trace organic species including carboxylic acids and organic compounds with -OH functionality. A second scenario excluded trace elements and a third assumed that derivatization steps to quantify polar organic compounds were not performed. Similar errors in source apportionment were seen with all three scenarios. In most cases, PMF failed to separate out factors corresponding to road dust and vegetative debris, two sources that made relatively uniform contributions to the synthetic exposures. Factors representing wood smoke, natural gas combustion, and meat cooking sources were difficult to identify due to a lack of unique tracers with concentrations reliably above the detection limits assumed in the study. Factors representing cigarette smoke, candle smoke, gasoline exhaust, and secondary aerosols were comparatively easy to identify. When contributions from a pair of sources, such as diesel and gasoline exhaust, were highly correlated in the synthetic datasets, a single factor corresponding to both sources was usually found.

  5. Source apportionment of fine and coarse particles at a roadside and urban background site in London during the 2012 summer ClearfLo campaign.

    PubMed

    Crilley, Leigh R; Lucarelli, Franco; Bloss, William J; Harrison, Roy M; Beddows, David C; Calzolai, Giulia; Nava, Silvia; Valli, Gianluigi; Bernardoni, Vera; Vecchi, Roberta

    2017-01-01

    London, like many major cities, has a noted air pollution problem, and a better understanding of the sources of airborne particles in the different size fractions will facilitate the implementation and effectiveness of control strategies to reduce air pollution. Thus, the trace elemental composition of the fine and coarse fraction were analysed at hourly time resolution at urban background (North Kensington, NK) and roadside (Marylebone Road, MR) sites within central London. Unlike previous work, the current study focuses on measurements during the summer providing a snapshot of contributing sources, utilising the high time resolution to improve source identification. Roadside enrichment was observed for a large number of elements associated with traffic emissions (Al, S, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Rb and Zr), while those elements that are typically from more regional sources (e.g. Na, Cl, S and K) were not found to have an appreciable increment. Positive Matrix Factorization (PMF) was applied for the source apportionment of the particle mass at both sites with similar sources being identified, including sea salt, airborne soil, traffic emissions, secondary inorganic aerosols and a Zn-Pb source. In the fine fraction, traffic emissions was the largest contributing source at MR (31.9%), whereas it was incorporated within an "urban background" source at NK, which had contributions from wood smoke, vehicle emissions and secondary particles. Regional sources were the major contributors to the coarse fraction at both sites. Secondary inorganic aerosols (which contained influences from shipping emissions and coal combustion) source factors accounted for around 33% of the PM10 at NK and were found to have the highest contributions from regional sources, including from the European mainland. Exhaust and non-exhaust sources both contribute appreciably to PM10 levels at the MR site, highlighting the continuing importance of vehicle-related air pollutants at

  6. Source apportionment and dynamic changes of carbonaceous aerosols during the haze bloom-decay process in China based on radiocarbon and organic molecular tracers

    NASA Astrophysics Data System (ADS)

    Liu, Junwen; Li, Jun; Liu, Di; Ding, Ping; Shen, Chengde; Mo, Yangzhi; Wang, Xinming; Luo, Chunling; Cheng, Zhineng; Szidat, Sönke; Zhang, Yanlin; Chen, Yingjun; Zhang, Gan

    2016-03-01

    Fine carbonaceous aerosols (CAs) is the key factor influencing the currently filthy air in megacities in China, yet few studies simultaneously focus on the origins of different CAs species using specific and powerful source tracers. Here, we present a detailed source apportionment for various CAs fractions, including organic carbon (OC), water-soluble OC (WSOC), water-insoluble OC (WIOC), elemental carbon (EC) and secondary OC (SOC) in the largest cities of North (Beijing, BJ) and South China (Guangzhou, GZ), using the measurements of radiocarbon and anhydrosugars. Results show that non-fossil fuel sources such as biomass burning and biogenic emission make a significant contribution to the total CAs in Chinese megacities: 56 ± 4 in BJ and 46 ± 5 % in GZ, respectively. The relative contributions of primary fossil carbon from coal and liquid petroleum combustions, primary non-fossil carbon and secondary organic carbon (SOC) to total carbon are 19, 28 and 54 % in BJ, and 40, 15 and 46 % in GZ, respectively. Non-fossil fuel sources account for 52 in BJ and 71 % in GZ of SOC, respectively. These results suggest that biomass burning has a greater influence on regional particulate air pollution in North China than in South China. We observed an unabridged haze bloom-decay process in South China, which illustrates that both primary and secondary matter from fossil sources played a key role in the blooming phase of the pollution episode, while haze phase is predominantly driven by fossil-derived secondary organic matter and nitrate.

  7. Source apportionment and dynamic changes of carbonaceous aerosols during the haze bloom-decay process in China based on radiocarbon and organic molecular tracers

    NASA Astrophysics Data System (ADS)

    Liu, J.; Li, J.; Liu, D.; Ding, P.; Shen, C.; Mo, Y.; Wang, X.; Luo, C.; Cheng, Z.; Szidat, S.; Zhang, Y.; Chen, Y.; Zhang, G.

    2015-12-01

    Fine carbonaceous aerosols (CAs) is the key factor influencing the currently filthy air in megacities of China, yet seldom study simultaneously focuses on the origins of different CAs species using specific and powerful source tracers. Here, we present a detailed source apportionment for various CAs fractions, including organic carbon (OC), water-soluble OC (WSOC), water-insoluble OC (WIOC), elemental carbon (EC) and secondary OC (SOC) in the largest cities of North (Beijing, BJ) and South China (Guangzhou, GZ), respectively, using the measurements of radiocarbon and anhydrosugars. Results show that non-fossil fuel sources such as biomass burning and biogenic emission make a significant contribution to the total CAs in Chinese megacities: 56 ± 4 % in BJ and 46 ± 5 % in GZ, respectively. The relative contributions of primary fossil carbon from coal and liquid petroleum combustions, primary non-fossil carbon and secondary organic carbon (SOC) to total carbon are 19, 28 and 54 % in BJ, and 40, 15 and 46 % in GZ, respectively. Non-fossil fuel sources account for 52 % in BJ and 71 % in GZ of SOC, respectively. These results suggest that biomass burning has a greater influence on regional particulate air pollution in North China than in South China. We observed an unabridged haze bloom-decay process in South China, which illustrates that both primary and secondary matter from fossil sources played a key role in the blooming phase of the pollution episode, while haze phase is predominantly driven by fossil-derived secondary organic matter and nitrate.

  8. Source Apportionment of PM2.5 using PMF and CMB: Comparison of the Effects of Transboundary and Local Pollutions in the Western Japan

    NASA Astrophysics Data System (ADS)

    Iijima, A.; Sugata, S.

    2014-12-01

    PM2.5 has become one of the most important aspects in recent air pollution issues. In Japan, the achievement rate of the environmental quality standard for PM2.5 is in a worse situation so far (43.3% for ambient air monitoring station, 33.3% for roadside air pollution monitoring station in FY2012). Therefore, source apportionment will be essential to policy and decision making for improving the PM2.5 pollution. Since 2011, we started the field monitoring study called "Current Status Elucidation and Source Contribution Assessment of PM2.5 Pollution in Collaboration with Environmental Research Institutes across Japan" which was granted by the Environment Research and Technology Development Fund (5B-1101) of the Ministry of the Environment, Japan. PM2.5 samples were collected at 14 sites during four campaigns. Chemical analyses of carbonaceous compounds, ionic species, and elements were conducted. Source apportionment was performed by using Positive Matrix Factorization (PMF, EPA PMF 3.0) and Chemical Mass Balance (CMB, EPA CMB 8.1) models. PMF model resolved a six-factor solution. Each of these factors has a distinctive grouping of species that can be associated with a specific source sector (F1: Biomass burning, F2: Sulfate + Oil combustion, F3: Industry, F4: Nitrate, F5: Sulfate + Coal combustion, and F6: Chloride). In the winter campaign (Jan. 24 to Feb. 7) in 2013, F5 accounted for 50% of total PM2.5 mass at Tsushima (34.2°N 129.3°E, the westernmost remote site). The contribution of F5 tended to decrease toward the eastern sites (27% at Fukuoka (33.5°N 130.5°E, urban site), 22% at Higashi-Osaka (34.7°N 135.6°E, urban site)). CMB model showed similar results in the same campaign. Coal combustion accounted for 49%, 30%, and 22% of total PM2.5 mass at Tsushima, Fukuoka, and Higashi-Osaka, respectively (Fig.1). On the other hand, at urban sites, higher contributions from local sources such as secondary nitrate (16% at Fukuoka, 21% at Higashi-Osaka), diesel fuel

  9. The AIRPARIF-AEROSOL project: A comprehensive source apportionment study of fine aerosols (PM2.5) in the region of Paris (France)

    NASA Astrophysics Data System (ADS)

    Sciare, Jean; Ghersi, Veronique; Bressi, Michael; Lameloise, Philippe; Bonnaire, Nicolas; Rosso, Amandine; Nicolas, Jose; Moukhtar, Sophie; Ferron, Anais; Baumier, Dominique

    2010-05-01

    With a population of about 12 millions inhabitants (20% of the French population), Greater Paris (France) is one of the most populated megacity in Europe and among the few located in developed countries. Due to its favorable geographical situation (far from other big European cities and influenced very often by clean oceanic air masses), it may be considered as a good candidate for investigating the build-up of urban air pollution from temperate industrialized countries. Particulate mass of fine aerosols with aerodynamic diameter below 2.5μm (PM2.5) is continuously monitored at several stations from great Paris for almost 8 years by the local air quality network (AIRPARIF), using a conventional on-line automatic system (R&P TEOM; see Patashnik and Rupprecht, 1991). During the period 2000-2006, levels of PM2.5 in the region of Paris have shown rather stable yearly mean values ranging 13 to 16?g/m3 whereas most of the other pollutants monitored by AIRPARIF have shown a net decrease during this period (http:\\www.airparif.asso.fr). Since the year 2007, this situation has becoming worse for particulate pollution with a net increase of the yearly mean concentration of PM2.5 (up to 21?g/m3), which increase is partly due to the use of a new PM2.5 measurement technique (R&P TEOM-FDMS instrument) enabling a proper determination of the semi-volatile fraction of fine aerosols. Although this new method greatly improves the determination of PM2.5, it has also brought PM2.5 levels in the region of Paris closer to the 25?g/m3 yearly mean targeted value recommended by Europe for 2010 (limit value for 2015). Efficient abatement policies aiming at reducing levels of PM2.5 in the region of Paris will have to be fed by preliminary PM2.5 source apportionment studies and exhaustive aerosol chemistry studies (chemical mass balance) allowing a better separation between regional to continental aerosol sources. The objective of the AIRPARIF-AEROSOL project aims to perform a spatially- and

  10. Source Apportionment of Volatile Organic Compounds and PM2.5 Using Positive Matrix Factorization in Two National Parks Impacted by Oil and Natural Gas Drilling Operations

    NASA Astrophysics Data System (ADS)

    Evanoski-Cole, A.; Prenni, A. J.; Sive, B. C.; Zhou, Y.; Benedict, K. B.; Day, D.; Schurman, M. I.; Sullivan, A.; Li, Y.; Callahan, S. L.; Hand, J. L.; Gebhart, K. A.; Schichtel, B. A.; Fischer, E. V.; Collett, J. L., Jr.

    2015-12-01

    As the oil and natural gas industry expands into rural areas of the United States, it is becoming increasingly important to investigate its impact on air quality in nearby national parks and other protected federal lands. Data from two different field studies centered in Rocky Mountain National Park, Colorado and the north unit of Theodore Roosevelt National Park, North Dakota will be used to perform a comprehensive source apportionment study. Measurements at both locations include volatile organic compounds (VOCs), PM2.5 and their precursor gases, and meteorological variables. Both sites are located near concentrated oil and natural gas operations but other local and regional emission sources differ. Other potential sources near Theodore Roosevelt National Park include increased diesel truck traffic, coal fired power plants and road dust. Rocky Mountain National Park is impacted by the transport of emissions from urban centers and agriculture in eastern Colorado. Additionally, the study at Theodore Roosevelt National Park occurred over two consecutive winters and the measurements at Rocky Mountain National Park were collected during the summer. Using these field study data and the EPA positive matrix factorization (PMF) tool, the different source factors for each field site will be investigated. In particular, the differences in the oil and gas factor from each study location will be discussed.

  11. Chemical characteristics and source apportionment of fine particulate organic carbon in Hong Kong during high particulate matter episodes in winter 2003

    NASA Astrophysics Data System (ADS)

    Li, Yun-Chun; Yu, Jian Zhen; Ho, Steven Sai Hang; Schauer, James J.; Yuan, Zibing; Lau, Alexis K. H.; Louie, Peter K. K.

    2013-02-01

    PM2.5 samples were collected at six general stations and one roadside station in Hong Kong in two periods of high particulate matter (PM) in 2003 (27 October-4 November and 30 November-13 December). The highest PM2.5 reached 216 μg m- 3 during the first high PM period and 113 μg m- 3 during the second high PM period. Analysis of synoptic weather conditions identified individual sampling days under dominant influence of one of three types of air masses, that is, local, regional and long-range transported (LRT) air masses. Roadside samples were discussed separately due to heavy influences from vehicular emissions. This research examines source apportionment of fine organic carbon (OC) and contribution of secondary organic aerosol on high PM days under different synoptic conditions. Six primary OC (POC) sources (vehicle exhaust, biomass burning, cooking, cigarette smoke, vegetative detritus, and coal combustion) were identified on the basis of characteristic organic tracers. Individual POC source contributions were estimated using chemical mass balance model. In the roadside and the local samples, OC was dominated by the primary sources, accounting for more than 74% of OC. In the samples influenced by regional and LRT air masses, secondary OC (SOC), which was approximated to be the difference between the total measured OC and the apportioned POC, contributed more than 54% of fine OC. SOC was highly correlated with water-soluble organic carbon and sulfate, consistent with its secondary nature.

  12. Source apportionment for sediment PAHs from the Daliao River (China) using an extended fit measurement mode of chemical mass balance model.

    PubMed

    Chen, Hai-Yang; Teng, Yan-Guo; Wang, Jin-Sheng

    2013-02-01

    To minimize the selection uncertainties of source profiles and obtain the higher model performance, an extended fit measurement mode for chemical mass balance model (EFMM-CMB) was proposed and applied to estimate source contributions for sediment PAHs from the Daliao River around which is the important industrial bases with oil, chemical and steel factories in the northeast part of China. Based on least squares fitting method, EFMM-CMB initially calculated the fit measurement index to every one of the possible combinations that can be made from the source profiles. Any successful applications of the fitting method were ranked according to performance measures, and then determined by maximizing an overall fitting index for a unique solution. Apportionment results from two case scenarios showed that the values of performance measures for EFMM-CMB were better to that for CMB8.2 results. With species selection of high molecular weight PAHs, power plant (45.75%), biomass burning (29.34%) and traffic tunnel (10.59%) were identified as the major sources of sediment PAHs from the Daliao River region.

  13. Application of stochastic models in identification and apportionment of heavy metal pollution sources in the surface soils of a large-scale region.

    PubMed

    Hu, Yuanan; Cheng, Hefa

    2013-04-16

    As heavy metals occur naturally in soils at measurable concentrations and their natural background contents have significant spatial variations, identification and apportionment of heavy metal pollution sources across large-scale regions is a challenging task. Stochastic models, including the recently developed conditional inference tree (CIT) and the finite mixture distribution model (FMDM), were applied to identify the sources of heavy metals found in the surface soils of the Pearl River Delta, China, and to apportion the contributions from natural background and human activities. Regression trees were successfully developed for the concentrations of Cd, Cu, Zn, Pb, Cr, Ni, As, and Hg in 227 soil samples from a region of over 7.2 × 10(4) km(2) based on seven specific predictors relevant to the source and behavior of heavy metals: land use, soil type, soil organic carbon content, population density, gross domestic product per capita, and the lengths and classes of the roads surrounding the sampling sites. The CIT and FMDM results consistently indicate that Cd, Zn, Cu, Pb, and Cr in the surface soils of the PRD were contributed largely by anthropogenic sources, whereas As, Ni, and Hg in the surface soils mostly originated from the soil parent materials.

  14. Simultaneous monitoring and compositions analysis of PM1 and PM2.5 in Shanghai: Implications for characterization of haze pollution and source apportionment.

    PubMed

    Qiao, Ting; Zhao, Mengfei; Xiu, Guangli; Yu, Jianzhen

    2016-07-01

    A year-long simultaneous observation of PM1 and PM2.5 were conducted at ECUST campus in Shanghai, the compositions were analyzed and compared. Results showed that PM2.5 was dominated by PM1 on clear days while the contribution of PM1-2.5 to PM2.5 increased on haze days, indicating that PM2.5 should be given priority to characterize or predict haze pollution. On haze days, accumulation of organic carbon (OC), elemental carbon (EC) and primary organic carbon (POC) in PM1-2.5 was faster than that in PM1. Humic-like substances carbon (Hulis-C) in both PM2.5 and PM1 formed faster than water soluble organic carbon (WSOC) on haze days, hence Hulis-C/WSOC increased with the intensification of haze pollution. In terms of water soluble ions, NO3(-)/SO4(2-) in PM1 increased with the aggravation of haze pollution, implying that mobile sources dominated on haze days, so is nitrogen oxidation ratio (NOR). Liquid water content (LWC) in both PM1 and PM2.5 had positive correlations with relative humidity (RH) but negative correlations with visibility, implying that hygroscopic growth might be a factor for visibility impairment, especially LWC in PM1. By comparison with multi-linear equations of LWC in PM1 and PM2.5, NO3(-) exerted a higher influence on hygroscopicity of PM1 than PM2.5, while RH, WSOC, SO4(2-) and NH4(+) had higher effects on PM2.5, especially WSOC. Source apportionment of PM2.5 was also investigated to provide reference for policy making. Cluster analysis by HYSPLIT (HYbrid Single Particle Lagrangian Integrated Trajectory) model showed that PM2.5 originated from marine aerosols, middle-scale transportation and large-scale transportation. Furthermore, PM2.5 on haze days was dominated by middle-scale transportation. In line with source apportionment by positive matrix factorization (PMF) model, PM2.5 was attributed to secondary inorganics, aged sea salt, combustion emissions, hygroscopic growth and secondary organics. Secondary formation was the principle source of

  15. The lichen transplant methodology in the source apportionment of metal deposition around a copper smelter in the former mining town of Karabash, Russia.

    PubMed

    Williamson, B J; Purvis, O W; Mikhailova, I N; Spiro, B; Udachin, V

    2008-06-01

    The lichen transplant monitoring methodology has been tested for source apportionment of metal deposition around the Cu smelter and former mining town of Karabash. Transplants of the lichen Hypogymnia physodes (L.) Nyl., collected from a 'control' site in July 2001, were set up at 10 stations along a 60 km NE-SW transect centred on Karabash. Samples were collected after 2 and 3 month monitoring periods and analysed using established wet-chemical techniques. The sources of particulate investigated were the smelter blast furnace and converter, floatation tailings, metallurgical slags, local road dusts, top soils and ambient airborne total suspended particulate. From multi-element least-squares modelling the blast furnace was the main source of particulate in transplants close to the smelter (<10 km). Particulate from the converter, with relatively high Pb and Zn, was found to be more widely dispersed, being finer-grained and so having a longer atmospheric residence time. Ambient airborne particulate, sampled in Karabash town using air-pump apparatus, was almost entirely derived from the converter, very different to the lichen transplants from the same area which mainly contained blast furnace particulate. It is proposed that lichens close to the smelter mainly trapped larger blast furnace-derived particulate as they have a low capture efficiency for smaller (converter) particles. The study demonstrates the utility of lichen transplants for monitoring atmospheric deposition and highlights the caution required in their use to assess ambient air quality in human health studies.

  16. Source apportionment of atmospheric PM2.5-bound polycyclic aromatic hydrocarbons by a PMF receptor model. Assessment of potential risk for human health.

    PubMed

    Callén, María Soledad; Iturmendi, Amaia; López, José Manuel

    2014-12-01

    One year sampling (2011-2012) campaign of airborne PM2.5-bound PAH was performed in Zaragoza, Spain. A source apportionment of total PAH by Positive Matrix Factorization (PMF) was applied in order to quantify potential PAH pollution sources. Four sources were apportioned: coal combustion, vehicular emissions, stationary emissions and unburned/evaporative emissions. Although Directive 2004/107/EC was fulfilled regarding benzo(a)pyrene (BaP), episodes exceeding the limit value of PM2.5 according to Directive 2008/50/EC were found. These episodes of high negative potential for human health were studied, obtaining a different pattern for the exceedances of PM2.5 and the lower assessment threshold of BaP (LATBaP). In both cases, stationary emissions contributed majority to total PAH. Lifetime cancer risk exceeded the unit risk recommended by the World Health Organization for those episodes exceeding the LATBaP and the PM2.5 exceedances for the warm season. For the cold season, the risk was higher for the LATBaP than for the PM2.5 exceedances.

  17. Chemical characterization and source apportionment of indoor and outdoor fine particulate matter (PM(2.5)) in retirement communities of the Los Angeles Basin.

    PubMed

    Hasheminassab, Sina; Daher, Nancy; Shafer, Martin M; Schauer, James J; Delfino, Ralph J; Sioutas, Constantinos

    2014-08-15

    Concurrent indoor and outdoor measurements of fine particulate matter (PM2.5) were conducted at three retirement homes in the Los Angeles Basin during two separate phases (cold and warm) between 2005 and 2006. Indoor-to-outdoor relationships of PM2.5 chemical constituents were determined and sources of indoor and outdoor PM2.5 were evaluated using a molecular marker-based chemical mass balance (MM-CMB) model. Indoor levels of elemental carbon (EC) along with metals and trace elements were found to be significantly affected by outdoor sources. EC, in particular, displayed very high indoor-to-outdoor (I/O) mass ratios accompanied by strong I/O correlations, illustrating the significant impact of outdoor sources on indoor levels of EC. Similarly, indoor levels of polycyclic aromatic hydrocarbons (PAHs), hopanes, and steranes were strongly correlated with their outdoor components and displayed I/O ratios close to unity. On the other hand, concentrations of n-alkanes and organic acids inside the retirement communities were dominated by indoor sources (e.g. food cooking and consumer products), as indicated by their I/O ratios, which exceeded unity. Source apportionment results revealed that vehicular emissions were the major contributor to both indoor and outdoor PM2.5, accounting for 39 and 46% of total mass, respectively. Moreover, the contribution of vehicular sources to indoor levels was generally comparable to its corresponding outdoor estimate. Other water-insoluble organic matter (other WIOM), which accounts for emissions from uncharacterized primary biogenic sources, displayed a wider range of contributions, varying from 2 to 73% of PM2.5, across all sites and phases of the study. Lastly, higher indoor than outdoor contribution of other water-soluble organic matter (other WSOM) was evident at some of the sites, suggesting the production of secondary aerosols as well as direct emissions from primary sources (including cleaning or other consumer products) at the

  18. Receptor models application to multi-year ambient PM 10 measurements in an industrialized ceramic area: Comparison of source apportionment results

    NASA Astrophysics Data System (ADS)

    Pandolfi, M.; Viana, M.; Minguillón, M. C.; Querol, X.; Alastuey, A.; Amato, F.; Celades, I.; Escrig, A.; Monfort, E.

    Ambient PM 10 data collected in one of the largest industrialized ceramic areas of Europe were used to study similarities and differences in the source apportionment results from three widespread receptor models: chemical mass balance (CMB), positive matrix factorization (PMF) and principal component analysis (PCA). Particulate emissions were collected from a variety of sources including soil dust and different mixed raw materials used for the manufacture of ceramic tiles in the area. The chemical profiles of these emission sources are presented in this work. The analysis of the PMF scaled residuals was used as a diagnostic tool for adjusting species uncertainties and to assess the PMF model fit by comparison with the robust CMB results. The Q robust value, the degree of correlation between the predicted and measured species concentrations, the sample-by-sample correlation of the PMF source contributions compared with the CMB improved after the new error structure was used within the PMF model. The robustness of the CMB analysis used for the comparison with the PMF analysis was inspected by means of the CMB performances parameters as well as by comparing the results with a previous CMB analysis performed on the same database but with different speciated source profiles. Moreover, the results showed that PMF and PCA models were not able to distinguish between the two most important sources of crustal material in the selected area (one natural and one anthropogenic). With the CMB model a contribution from both sources was calculated without observing collinearity between the profiles. However, high correlation was found by adding the two crustal contributions from CMB and comparing the results with the single crustal factor from PCA and PMF. Low correlation was observed between the contribution values of the vehicular source for each model pairs. The lack of a local vehicular experimental profile for the CMB analysis and the non-specific chemical speciation performed

  19. Source apportionment of atmospheric pollutants based on the online data by using PMF and ME2 models at a megacity, China

    NASA Astrophysics Data System (ADS)

    Liu, Baoshuang; Yang, Jiamei; Yuan, Jie; Wang, Jiao; Dai, Qili; Li, Tingkun; Bi, Xiaohui; Feng, Yinchang; Xiao, Zhimei; Zhang, Yufen; Xu, Hong

    2017-03-01

    From 1st June to 31st August 2015, the online datasets (the water soluble inorganic ions (WSIIs), OC and EC in PM2.5, and SO2, NO2, NO) were measured continuously at Tianjin. Source apportionment of atmospheric pollutants was carried out by using PMF and ME2 models based on the online datasets. During summer in Tianjin, the ammonium sulfate/ammonium hydrogen sulfate might be major forms of sulfate in the atmospheric aerosol, while the ammonium nitrate might be major forms of nitrate. The poor correlation between OC and EC might be caused by the changes of emission sources and the production of secondary organic carbon (SOC). Five source-categories that contributed to atmospheric pollutants were extracted by PMF and ME2 models, respectively. The profiles calculated by PMF and ME2 models were consistent, and the source contributions estimated by the two models were also similar. The correlations (R2 = 0.84-0.94) were better on the time series of the contributed concentrations for the same source-category calculated from PMF and ME2 models. The source-categories were identified as secondary sources (the contribution of 25.4-26.1%), vehicle exhaust (23.3-25.4%), coal combustion (16.5-18.2%), crustal dust (13.2-14.0%) and biomass burning (9.1-10.2%). For the same source-category identified from PMF and ME2 models, the differences of profiles might be attributed to the differences of calculated methods from the two models and the uncertainties of the online datasets.

  20. Chemical Characterization and Source Apportionment of Indoor and Outdoor Fine Particulate Matter (PM2.5) in Retirement Communities of the Los Angeles Basin

    PubMed Central

    Hasheminassab, Sina; Daher, Nancy; Shafer, Martin M.; Schauer, James J.; Delfino, Ralph J.; Sioutas, Constantinos

    2014-01-01

    Concurrent indoor and outdoor measurements of fine particulate matter (PM2.5) were conducted at three retirement homes in the Los Angeles Basin during two separate phases (cold and warm) between 2005 and 2006. Indoor-to-outdoor relationships of PM2.5 chemical constituents were determined and sources of indoor and outdoor PM2.5 were evaluated using a molecular marker-based chemical mass balance (MM-CMB) model. Indoor levels of elemental carbon (EC) along with metals and trace elements were found to be significantly affected by outdoor sources. EC, in particular, displayed very high indoor-to-outdoor (I/O) mass ratios accompanied by strong I/O correlations, illustrating the significant impact of outdoor sources on indoor levels of EC. Similarly, indoor levels of polycyclic aromatic hydrocarbons (PAHs), hopanes, and steranes were strongly correlated with their outdoor components and displayed I/O ratios close to unity. On the other hand, concentrations of n-alkanes and organic acids inside the retirement communities were dominated by indoor sources (e.g. food cooking and consumer products), as indicated by their I/O ratios, which exceeded unity. Source apportionment results revealed that vehicular emissions were the major contributor to both indoor and outdoor PM2.5, accounting for 39 and 46% of total mass, respectively. Moreover, the contribution of vehicular sources to indoor levels was generally comparable to its corresponding outdoor estimate. Other water-insoluble organic matter (other WIOM), which accounts for emissions from uncharacterized primary biogenic sources, displayed a wider range of contributions, varying from 2 to 73% of PM2.5, across all sites and phases of the study. Lastly, higher indoor than outdoor contribution of other water-soluble organic matter (other WSOM) was evident at some of the sites, suggesting the production of secondary aerosols as well as direct emissions from primary sources (including cleaning or other consumer products) at the

  1. Source apportionment of size-fractionated particles during the 2013 Asian Youth Games and the 2014 Youth Olympic Games in Nanjing, China.

    PubMed

    Chen, Pulong; Wang, Tijian; Lu, Xiaobo; Yu, Yiyong; Kasoar, Matthew; Xie, Min; Zhuang, Bingliang

    2017-02-01

    In this study, samples of size-fractionated particulate matter were collected continuously using a 9-size interval cascade impactor at an urban site in Nanjing, before, during and after the Asian Youth Games (AYG), from July to September of 2013, and the Youth Olympic Games (YOG), from July to September of 2014. First, elemental concentrations, water-soluble ions including Cl(-), NO3(-), SO4(2-), NH4(+), K(+), Na(+) and Ca(2+), organic carbon (OC) and elemental carbon (EC) were analysed. Then, the source apportionment of the fine and coarse particulate matter was carried out using the chemical mass balance (CMB) model. The average PM10 concentrations were 90.4±20.0μg/m(3) during the 2013 AYG and 70.6±25.3μg/m(3) during the 2014 YOG. For PM2.1, the average concentrations were 50.0±12.8μg/m(3) in 2013 and 34.6±17.0μg/m(3) in 2014. Investigations showed that the average concentrations of particles declined significantly from 2013 to 2014, and concentrations were at the lowest levels during the events. Results indicated that OC, EC, sulfate and crustal elements have significant monthly and size-based variations. The major components, including crustal elements, water-soluble ions and carbonaceous aerosol accounted for 75.3-91.9% of the total particulate mass concentrations during the sampling periods. Fugitive dust, coal combustion dust, iron dust, construction dust, soil dust, vehicle exhaust, secondary aerosols and sea salt have been classified as the main emissions in Nanjing. The source apportionment results indicate that the emissions from fugitive dust, which was the most abundance emission source during the 2013 AYG, contributed to 23.0% of the total particle mass. However, fugitive dust decreased to 6.2% of the total particle mass during the 2014 YOG. Construction dust (14.7% versus 7.8% for the AYG and the YOG, respectively) and secondary sulfate aerosol (9.3% versus 8.0% for the AYG and the YOG, respectively) showed the same trend as fugitive dust

  2. Water quality assessment and apportionment of pollution sources using APCS-MLR and PMF receptor modeling techniques in three major rivers of South Florida.

    PubMed

    Haji Gholizadeh, Mohammad; Melesse, Assefa M; Reddi, Lakshmi

    2016-10-01

    In this study, principal component analysis (PCA), factor analysis (FA), and the absolute principal component score-multiple linear regression (APCS-MLR) receptor modeling technique were used to assess the water quality and identify and quantify the potential pollution sources affecting the water quality of three major rivers of South Florida. For this purpose, 15years (2000-2014) dataset of 12 water quality variables covering 16 monitoring stations, and approximately 35,000 observations was used. The PCA/FA method identified five and four potential pollution sources in wet and dry seasons, respectively, and the effective mechanisms, rules and causes were explained. The APCS-MLR apportioned their contributions to each water quality variable. Results showed that the point source pollution discharges from anthropogenic factors due to the discharge of agriculture waste and domestic and industrial wastewater were the major sources of river water contamination. Also, the studied variables were categorized into three groups of nutrients (total kjeldahl nitrogen, total phosphorus, total phosphate, and ammonia-N), water murkiness conducive parameters (total suspended solids, turbidity, and chlorophyll-a), and salt ions (magnesium, chloride, and sodium), and average contributions of different potential pollution sources to these categories were considered separately. The data matrix was also subjected to PMF receptor model using the EPA PMF-5.0 program and the two-way model described was performed for the PMF analyses. Comparison of the obtained results of PMF and APCS-MLR models showed that there were some significant differences in estimated contribution for each potential pollution source, especially in the wet season. Eventually, it was concluded that the APCS-MLR receptor modeling approach appears to be more physically plausible for the current study. It is believed that the results of apportionment could be very useful to the local authorities for the control and

  3. A new methodology to assess the performance and uncertainty of source apportionment models II: The results of two European intercomparison exercises

    NASA Astrophysics Data System (ADS)

    Belis, C. A.; Karagulian, F.; Amato, F.; Almeida, M.; Artaxo, P.; Beddows, D. C. S.; Bernardoni, V.; Bove, M. C.; Carbone, S.; Cesari, D.; Contini, D.; Cuccia, E.; Diapouli, E.; Eleftheriadis, K.; Favez, O.; El Haddad, I.; Harrison, R. M.; Hellebust, S.; Hovorka, J.; Jang, E.; Jorquera, H.; Kammermeier, T.; Karl, M.; Lucarelli, F.; Mooibroek, D.; Nava, S.; Nøjgaard, J. K.; Paatero, P.; Pandolfi, M.; Perrone, M. G.; Petit, J. E.; Pietrodangelo, A.; Pokorná, P.; Prati, P.; Prevot, A. S. H.; Quass, U.; Querol, X.; Saraga, D.; Sciare, J.; Sfetsos, A.; Valli, G.; Vecchi, R.; Vestenius, M.; Yubero, E.; Hopke, P. K.

    2015-12-01

    The performance and the uncertainty of receptor models (RMs) were assessed in intercomparison exercises employing real-world and synthetic input datasets. To that end, the results obtained by different practitioners using ten different RMs were compared with a reference. In order to explain the differences in the performances and uncertainties of the different approaches, the apportioned mass, the number of sources, the chemical profiles, the contribution-to-species and the time trends of the sources were all evaluated using the methodology described in Belis et al. (2015). In this study, 87% of the 344 source contribution estimates (SCEs) reported by participants in 47 different source apportionment model results met the 50% standard uncertainty quality objective established for the performance test. In addition, 68% of the SCE uncertainties reported in the results were coherent with the analytical uncertainties in the input data. The most used models, EPA-PMF v.3, PMF2 and EPA-CMB 8.2, presented quite satisfactory performances in the estimation of SCEs while unconstrained models, that do not account for the uncertainty in the input data (e.g. APCS and FA-MLRA), showed below average performance. Sources with well-defined chemical profiles and seasonal time trends, that make appreciable contributions (>10%), were those better quantified by the models while those with contributions to the PM mass close to 1% represented a challenge. The results of the assessment indicate that RMs are capable of estimating the contribution of the major pollution source categories over a given time window with a level of accuracy that is in line with the needs of air quality management.

  4. Source apportionment of methane and nitrous oxide in California's San Joaquin Valley at CalNex 2010 via positive matrix factorization

    NASA Astrophysics Data System (ADS)

    Guha, A.; Gentner, D. R.; Weber, R. J.; Provencal, R.; Goldstein, A. H.

    2015-03-01

    Sources of methane (CH4) and nitrous oxide (N2O) were investigated using measurements from a site in southeast Bakersfield as part of the CalNex (California at the Nexus of Air Quality and Climate Change) experiment from 15 May to 30 June 2010. Typical daily minimum mixing ratios of CH4 and N2O were higher than daily averages that were simultaneously observed at a similar latitude background station (NOAA, Mauna Loa) by approximately 70 and 0.5 ppb, respectively. Substantial enhancements of CH4 and N2O (hourly averages > 500 ppb and > 7 ppb, respectively) were routinely observed suggesting the presence of large regional sources. Collocated measurements of carbon monoxide (CO) and a range of volatile organic compounds (VOCs) (e.g. straight-chain and branched alkanes, cycloalkanes, chlorinated alkanes, aromatics, alcohols, isoprene, terpenes and ketones) were used with a Positive Matrix Factorization (PMF) source apportionment method to estimate the contribution of regional sources to observed enhancements of CH4 and N2O. The PMF technique provided a "top-down" deconstruction of ambient gas-phase observations into broad source categories, yielding a 7-factor solution. We identified these source factors as emissions from evaporative and fugitive; motor vehicles; livestock and dairy; agricultural and soil management; daytime light and temperature driven; non-vehicular urban; and nighttime terpene biogenics and anthropogenics. The dairy and livestock factor accounted for a majority of the CH4 (70-90%) enhancements during the duration of the experiments. Propagation of uncertainties in the PMF-derived factor profiles and time series from bootstrapping analysis resulted in a 29% uncertainty in the CH4 apportionment to this factor. The dairy and livestock factor was also a principal contributor to the daily enhancements of N2O (60-70%) with an uncertainty of 33%. Agriculture and soil management accounted for ~20-25% of N2O enhancements over the course of a day, not

  5. Single particle mass spectral signatures from vehicle exhaust particles and the source apportionment of on-line PM2.5 by single particle aerosol mass spectrometry.

    PubMed

    Yang, Jian; Ma, Shexia; Gao, Bo; Li, Xiaoying; Zhang, Yanjun; Cai, Jing; Li, Mei; Yao, Ling'ai; Huang, Bo; Zheng, Mei

    2017-03-24

    In order to accurately apportion the many distinct types of individual particles observed, it is necessary to characterize fingerprints of individual particles emitted directly from known sources. In this study, single particle mass spectral signatures from vehicle exhaust particles in a tunnel were performed. These data were used to evaluate particle signatures in a real-world PM2.5 apportionment study. The dominant chemical type originating from average positive and negative mass spectra for vehicle exhaust particles are EC species. Four distinct particle types describe the majority of particles emitted by vehicle exhaust particles in this tunnel. Each particle class is labeled according to the most significant chemical features in both average positive and negative mass spectral signatures, including ECOC, NaK, Metal and PAHs species. A single particle aerosol mass spectrometry (SPAMS) was also employed during the winter of 2013 in Guangzhou to determine both the size and chemical composition of individual atmospheric particles, with vacuum aerodynamic diameter (dva) in the size range of 0.2-2μm. A total of 487,570 particles were chemically analyzed with positive and negative ion mass spectra and a large set of single particle mass spectra was collected and analyzed in order to identify the speciation. According to the typical tracer ions from different source types and classification by the ART-2a algorithm which uses source fingerprints for apportioning ambient particles, the major sources of single particles were simulated. Coal combustion, vehicle exhaust, and secondary ion were the most abundant particle sources, contributing 28.5%, 17.8%, and 18.2%, respectively. The fraction with vehicle exhaust species particles decreased slightly with particle size in the condensation mode particles.

  6. Ambient PM2.5-bound polycyclic aromatic hydrocarbons (PAHs) in Changhua County, central Taiwan: Seasonal variation, source apportionment and cancer risk assessment.

    PubMed

    Chen, Yu-Cheng; Chiang, Hung-Che; Hsu, Chin-Yu; Yang, Tzu-Ting; Lin, Tzu-Yu; Chen, Mu-Jean; Chen, Nai-Tzu; Wu, Yuh-Shen

    2016-11-01

    This study investigates PM2.5-bound PAHs for rural sites (Dacheng and Fangyuan) positioned close to heavy air-polluting industries in Changhua County, central Taiwan. A total of 113 PM2.5 samples with 22 PAHs collected from 2014 to 2015 were analyzed, and Positive Matrix Factorization (PMF) and diagnostic ratios of PAHs were applied to quantify potential PAH sources. The influences of local and regional sources were also explored using the conditional probability function (CPF) and potential source contribution function (PSCF) with PMF-modeled results, respectively. Annual mean concentrations of total PAHs were 2.91 ± 1.34 and 3.04 ± 1.40 ng/m(3) for Dacheng and Fangyuan, respectively, and their corresponding BaPeq were measured at 0.534 ± 0.255 and 0.563 ± 0.273 ng/m(3) in concentration. Seasonal variations with higher PAHs found for the winter than for the spring and summer were observed for both sites. The lifetime excess cancer risk (ECR) from inhalation exposure to PAHs was recorded as 4.7 × 10(-5) overall. Potential sources of PM2.5-bound PAHs include unburned petroleum and traffic emissions (42%), steel industry and coal combustion (31%), and petroleum and oil burning (27%), and unburned petroleum and traffic emission could contribute the highest ECR (2.4 × 10(-5)). The CPF results show that directional apportionment patterns were consistent with the actual locations of local PAH sources. The PSCF results indicate that mainly northeastern regions of China have contributed elevated PM2.5-bound PAHs from long-range transports.

  7. Inter-comparison of source apportionment of PM10 using PMF and CMB in three sites nearby an industrial area in central Italy

    NASA Astrophysics Data System (ADS)

    Cesari, Daniela; Donateo, Antonio; Conte, Marianna; Contini, Daniele

    2016-12-01

    Receptor models (RMs), based on chemical composition of particulate matter (PM), such as Chemical Mass Balance (CMB) and Positive Matrix Factorization (PMF), represent useful tools for determining the impact of PM sources to air quality. This information is useful, especially in areas influenced by anthropogenic activities, to plan mitigation strategies for environmental management. Recent inter-comparison of source apportionment (SA) results showed that one of the difficulties in the comparison of estimated source contributions is the compatibility of the sources, i.e. the chemical profiles of factor/sources used in receptor models. This suggests that SA based on integration of several RMs could give more stable and reliable solutions with respect to a single model. The aim of this work was to perform inter-comparison of PMF (using PMF3.0 and PMF5.0 codes) and CMB outputs, focusing on both source chemical profiles and estimates of source contributions. The dataset included 347 daily PM10 samples collected in three sites in central Italy located near industrial emissions. Samples were chemically analysed for the concentrations of 21 chemical species (NH4+, Ca2 +, Mg2 +, Na+, K+, Mg2 +, SO42 -, NO3-, Cl-, Si, Al, Ti, V, Mn, Fe, Ni, Cu, Zn, Br, EC, and OC) used as input of RMs. The approach identified 9 factor/sources: marine, traffic, resuspended dust, biomass burning, secondary sulphate, secondary nitrate, crustal, coal combustion power plant and harbour-industrial. Results showed that the application of constraints in PMF5.0 improved interpretability of profiles and comparability of estimated source contributions with stoichiometric calculations. The inter-comparison of PMF and CMB gave significant differences for secondary nitrate, biomass burning, and harbour-industrial sources, due to non-compatibility of these source profiles that have local specificities. When these site-dependent specificities were taken into account, optimising the input source profiles of

  8. Stable carbon isotopic ratio measurement of polycyclic aromatic hydrocarbons as a tool for source identification and apportionment--a review of analytical methodologies.

    PubMed

    Buczyńska, A J; Geypens, B; Van Grieken, R; De Wael, K

    2013-02-15

    The measurement of the ratio of stable isotopes of carbon ((13)C/(12)C expressed as a δ(13)C) in the individual components of a sample may be used as a means to identify the origin of these components. This article reviews the approaches and reports on the successes and failures of source identification and apportionment of Polycyclic Aromatic Hydrocarbons (PAHs) with the use of compound-specific isotope analysis (CSIA). One of the conditions for a precise and accurate analysis of isotope ratios with the use of GC-C-IRMS is the need for well separated peaks, with no co-elutions, and reduced unresolved complex mixture (UCM). Additionally, special care needs to be taken for an investigation of possible isotope fractionation effects introduced during the analytical treatment of samples. With the above-mentioned problems in mind, this review discusses in detail and compares current laboratory methodologies, mainly in the extraction and subsequent clean-up techniques used for environmental samples (air particulate matter, soil and sediments). Sampling strategies, the use of isotopic internal standards and the ranges for precision and accuracy are also reported and discussed.

  9. Seasonal and spatial variation of trace elements in multi-size airborne particulate matters of Beijing, China: Mass concentration, enrichment characteristics, source apportionment, chemical speciation and bioavailability

    NASA Astrophysics Data System (ADS)

    Gao, Jiajia; Tian, Hezhong; Cheng, Ke; Lu, Long; Wang, Yuxuan; Wu, Ye; Zhu, Chuanyong; Liu, Kaiyun; Zhou, Junrui; Liu, Xingang; Chen, Jing; Hao, Jiming

    2014-12-01

    The seasonal and spatial variation characteristics of 19 elements (Al, As, Be, Ca, Cd, Co, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, Pb, S, Sb, Se, Zn) in TSP/PM10/PM2.5 samples were investigated, which were collected from April 2011 to January 2012 simultaneously at an urban downtown site, a traffic roadside site, a suburban site, and a rural site in Beijing. The elevated concentrations of several toxic trace elements (As, Cd, Mn, Ni, Pb, etc.) in particles revealed that the contamination of toxic elements in Beijing could not be neglected. Positive matrix factorization method (PMF) was applied for source apportionment of trace elements in PM, and three factors (crust related sources, combustion sources, and traffic and steel industrial related sources) were identified. Furthermore, the chemical speciation and bioavailability of various elements were identified by applying European Community Bureau of Reference (BCR) procedure. Our results showed that eight toxic elements (As, Cd, Cr, Cu, Ni, Pb, Sb and Zn) exhibited higher mobility in PM2.5 than in PM10. Notably, elements of As, Cd, Pb and Zn were presented with higher mobility than the other elements, and these elements were lightly to release into the environment and easily available to human body. Additionally, As, Cd, Pb and Zn also accounted for higher percentages in the bound to mobile fractions at the central urban areas of Beijing. Therefore, special concerns should be paid to these toxic trace elements which had relatively high mobility in fine particles, when planning and implementing the comprehensive air pollution mitigation policies in Beijing.

  10. [Ozone source apportionment at urban area during a typical photochemical pollution episode in the summer of 2013 in the Yangtze River Delta].

    PubMed

    Li, Hao; Li, Li; Huang, Cheng; An, Jing-yu; Yan, Ru-sha; Huang, Hai-ying; Wang, Yang-jun; Lu, Qing; Wang, Qian; Lou, Sheng-rong; Wang, Hong-li; Zhou, Min; Tao, Shi-kang; Qiao, Li-ping; Chen, Ming-hua

    2015-01-01

    With the fast development of urbanization, industrialization and mobilization, the air pollutant emissions with photochemical reactivity become more obvious, causing a severe photochemical pollution with the characteristics of high ozone concentration. However, the ozone source identification is very complicated due to the high non linearity between ozone and its precursors. Thus, ways to reduce ozone is still not clear. A high ozone pollution episode occurred during July, 2013, which lasted for a long period, with large influence area and high intensity. In this paper, we selected this episode to do a case study with the application of ozone source apportionment technology(OSAT) coupled within the CAMx air quality model. In this study, 4 source regions(including Shanghai, north Zhejiang, South Jiangsu and long range transport), 7 source categories (including power plants, industrial process, industrial boilers and kilns, residential, mobile source, volatile source and biogenic emissions) are analyzed to study their contributions to surface O3 in Shanghai, Suzhou and Zhejiang. Results indicate that long range transport contribution to the surface ozone in the YRD is around 20 x 10(-9) - 40 x 10(-9) (volume fraction). The O3 concentrations can increased to 40 x 10(-9) - 100 x 10(-9) (volume fraction) due to precursors emissions in Shanghai, Jiangsu and Zhejiang. As for the regional contribution to 8 hour ozone, long range transport constitutes 42.79% +/- 10.17%, 48.57% +/- 9.97% and 60.13% +/- 7.11% of the surface ozone in Shanghai, Suzhou and Hangzhou, respectively. Regarding the high O3 in Shanghai, local contribution is 28.94% +/- 8.49%, north Zhejiang constitutes 19.83% +/- 10.55%. As for surface O3 in Suzhou, the contribution from south Jiangsu is 26.41% +/- 6.80%. Regarding the surface O3 in Hangzhou, the major regional contributor is north Zhejiang (29.56% +/- 8.33%). Contributions from the long range transport to the daily maximum O3 concentrations are

  11. Limitation of using Angstrom exponent for source apportionment of black carbon in complex environments - A case study from the North West Indo- Gangetic plain

    NASA Astrophysics Data System (ADS)

    Garg, S.; Sinha, B.; Sinha, V.; Chandra, P.; Sarda Esteve, R.; Gros, V.

    2015-12-01

    Determining the contribution of different sources to the total BC is necessary for targeted mitigation. Absorption Angstrom exponent (αabs) measurements of black carbon (BC) have recently been introduced as a novel tool to apportion the contribution of biomass burning sources to BC. Two-component Aethalometer model for apportioning BC to biomass burning sources and fossil fuel combustion sources, which uses αabs as a generic indicator of the source type, is widely used for determining the contribution of the two types of sources to the total BC. Our work studies BC emissions in the highly-populated, anthropogenic emissions-dominated Indo-Gangetic Plain and demonstrates that the αabs cannot be used as a generic tracer for biomass burning emissions in a complex environment. Simultaneously collected high time resolution data from a 7-wavelength Aethalometer (AE 42, Magee Scientific, USA) and a high sensitivity Proton Transfer Reaction- Quadrupole Mass Spectrometer (PTR-MS) installed at a sub-urban site in Mohali (Punjab), India, were used to identify a number of biomass combustion plumes during which BC enhancements correlated strongly with an increase in acetonitrile (a well-established biomass burning tracer) mixing ratio. Each type of biomass combustion is classified and characterized by distinct emission ratios of aromatic compounds and oxygenated VOCs to acetonitrile. The identified types of biomass combustion include two different types of crop residue burning (paddy and wheat), burning of leaf-litter, and garbage burning. Traffic (fossil-fuel burning) plumes were also selected for comparison. We find that the two-component Aethalometer source-apportionment method cannot be extrapolated to all types of biomass combustion and αabs of traffic plumes can be >1 in developing countries like India, where use of adulterated fuel in vehicles is common. Thus in a complex environment, where multiple anthropogenic BC sources and air masses of variable photochemical age

  12. Elemental quantification, chemistry, and source apportionment in golf course facilities in a semi-arid urban landscape using a portable X-ray fluorescence spectrometer

    NASA Astrophysics Data System (ADS)

    Udeigwe, T. K.; Young, J.; Kandakji, T.; Weindorf, D. C.; Mahmoud, M. A.; Stietiya, M. H.

    2015-04-01

    This study extends the application of the portable X-ray fluorescence (PXRF) spectrometry to the examination of elements in semi-arid urban landscapes of the Southern High Plains (SHP) of the United States, focusing on golf courses. The complex environmental challenges of this region and the unique management practices at golf course facilities could lead to differences in concentration and in the chemistry of elements between managed (irrigated) and non-managed (non-irrigated) portions of these facilities. Soil samples were collected at depths of 0-10, 10-20, and 20-30 cm from managed and non-managed areas of seven different facilities in the city of Lubbock, Texas, and analyzed for a suite of soil properties. Total elemental quantification was conducted using a PXRF spectrometer. Findings mostly indicated no significant differences in the concentration of examined elements between the managed and non-managed areas of the facilities. However, strong positive relationships (R = 0.82-0.91, p < 0.001) were observed among elements (e.g., Fe on the one hand and Cr, Mn, Ni, and As on the other; Cu and Zn; As and Cr) and between these elements and soil constituents or properties such as clay, calcium carbonate, organic matter, and pH. The strengths of these relationships were mostly higher in the non-managed areas, suggesting a possible alteration in the chemistry of these elements by anthropogenic influences in the managed areas. Principal component and correlation analyses within the managed areas suggested that As, Cr, Fe, Mn, and Ni could be of lithogenic origin, while Cu, Pb, and Zn could have anthropogenic influences. Only one possible, likely lithogenic, source of the elements was identified within the non-managed areas. As evidenced by the study, the PXRF spectrometer can be a valuable tool for elemental quantification and rapid investigation of elemental interaction and source apportionment in semi-arid climates.

  13. Elemental quantification, chemistry, and source apportionment in golf course facilities in semi-arid urban landscape using portable x-ray fluorescence spectrometer

    NASA Astrophysics Data System (ADS)

    Udeigwe, T. K.; Young, J.; Kandakji, T.; Weindorf, D. C.; Mahmoud, M. A.; Stietiya, M. H.

    2015-01-01

    This study extends the application of the portable x-ray fluorescence (PXRF) spectrometry to examination of elements in semi-arid urban landscapes of the Southern High Plains (SHP) of the United States (US), focusing on golf courses. The complex environmental challenges of this region and the unique management practices at golf course facilities could lead to differences in concentration and chemistry of elements between managed (irrigated) and non-managed (non-irrigated) portions of these facilities. Soil samples were collected at the depths of 0-10, 10-20, and 20-30 cm from managed and non-managed areas of seven different facilities in the city of Lubbock, Texas, and analyzed for a suite of soil properties. Total elemental quantification was conducted using PXRF. Findings mostly indicated no significant differences in concentration of examined elements between the managed and non-managed areas of the facilities. However, strong positive relationships (R2 = 0.82-0.91, p < 0.001) were observed among elements (e.g. Fe and each of Cr, Mn, Ni, and As; Cu and Zn; As and Cr) and between these elements and soil constituents or properties such as clay, calcium carbonate, organic matter, and pH. The strengths of these relationships were mostly higher in the non-managed areas, suggesting possible alteration in the chemistry of these elements by anthropogenic influences. Principal component analyses (PCA) and correlation analyses within the managed areas suggested that As, Cr, Fe, Mn, and Ni could be of lithogenic origin, while Cu, Pb, and Zn were attributed to anthropogenic influences. Only one possible source of element, likely lithogenic, was identified within non-managed areas. As evidenced from the study, the PXRF can be a valuable tool for elemental quantification, and rapid investigation of elemental interaction and source apportionment in semi-arid climates.

  14. Polybrominated Diphenyl Ethers (PBDEs) in paired human hair and serum from e-waste recycling workers: source apportionment of hair PBDEs and relationship between hair and serum.

    PubMed

    Zheng, Jing; Chen, Ke-Hui; Luo, Xiao-Jun; Yan, Xiao; He, Chun-Tao; Yu, Yun-Jiang; Hu, Guo-Cheng; Peng, Xiao-Wu; Ren, Ming-Zhong; Yang, Zhong-Yi; Mai, Bi-Xian

    2014-01-01

    Human hair has been widely used as a bioindicator for human persistent organic pollutants (POPs) exposure, but studies on the sources of hair POPs and the relationship between hair and body burden are limited. This study analyzed the possible source apportionment of hair PBDEs and examined the relationship between PBDE concentrations in paired hair and serum from e-waste recycling workers. Using the ratio of BDE 99/47 and BDE 209/207 as indices, we calculated that only 15% of the highly brominated congeners (nona- and deca-BDE congeners) comes from exogenous (external) exposure for both female and male hair, but an average of 64% and 55% of the lower-brominated congeners (tetra- to penta-BDE congeners) come from exogenous exposure for female and male hair, respectively. The higher contribution of exogenous exposure for less-brominated congeners could be related to their relatively lower log KOW and higher volatility than higher-brominated congeners, which make them more readily to evaporate from dust and then to be adsorbed on hair. Higher hair PBDE levels and higher exogenous exposure of less-brominated congeners in females than in males can be attributed to a longer exogenous exposure time for females than males. Significant positive relationships were found in tri- to hepta-BDE congeners (BDE 28, 47, 66, 85, 100, 153, 154, and 183) (R = 0.36-0.55, p < 0.05) between hair and serum, but this relationship was not found for octa- to deca-BDE. Difference in the half-lives between highly brominated congeners and less-brominated congeners could be a reason. This result also implied that we should treat the results of correlation analyses between hair and other organs cautiously.

  15. Argon offline-AMS source apportionment of organic aerosol over yearly cycles for an urban, rural, and marine site in northern Europe

    NASA Astrophysics Data System (ADS)

    Bozzetti, Carlo; Sosedova, Yuliya; Xiao, Mao; Daellenbach, Kaspar R.; Ulevicius, Vidmantas; Dudoitis, Vadimas; Mordas, Genrik; Byčenkienė, Steigvilė; Plauškaitė, Kristina; Vlachou, Athanasia; Golly, Benjamin; Chazeau, Benjamin; Besombes, Jean-Luc; Baltensperger, Urs; Jaffrezo, Jean-Luc; Slowik, Jay G.; El Haddad, Imad; Prévôt, André S. H.

    2017-01-01

    The widespread use of Aerodyne aerosol mass spectrometers (AMS) has greatly improved real-time organic aerosol (OA) monitoring, providing mass spectra that contain sufficient information for source apportionment. However, AMS field deployments remain expensive and demanding, limiting the acquisition of long-term datasets at many sampling sites. The offline application of aerosol mass spectrometry entailing the analysis of nebulized water extracted filter samples (offline-AMS) increases the spatial coverage accessible to AMS measurements, being filters routinely collected at many stations worldwide. PM1 (particulate matter with an aerodynamic diameter < 1 µm) filter samples were collected during an entire year in Lithuania at three different locations representative of three typical environments of the southeast Baltic region: Vilnius (urban background), Rūgšteli\\vskis (rural terrestrial), and Preila (rural coastal). Aqueous filter extracts were nebulized in Ar, yielding the first AMS measurements of water-soluble atmospheric organic aerosol (WSOA) without interference from air fragments. This enables direct measurement of the CO+ fragment contribution, whose intensity is typically assumed to be equal to that of CO2+. Offline-AMS spectra reveal that the water-soluble CO2+ : CO+ ratio not only shows values systematically > 1 but is also dependent on season, with lower values in winter than in summer. AMS WSOA spectra were analyzed using positive matrix factorization (PMF), which yielded four factors. These factors included biomass burning OA (BBOA), local OA (LOA) contributing significantly only in Vilnius, and two oxygenated OA (OOA) factors, summer OOA (S-OOA) and background OOA (B-OOA), distinguished by their seasonal variability. The contribution of traffic exhaust OA (TEOA) was not resolved by PMF due to both low concentrations and low water solubility. Therefore, the TEOA concentration was estimated using a chemical mass balance approach, based on the

  16. Source apportionment of PM10 and PM(2.5) at Tocopilla, Chile (22 degrees 05' S, 70 degrees 12' W).

    PubMed

    Jorquera, Héctor

    2009-06-01

    Tocopilla is located on the coast of Northern Chile, within an arid region that extends from 30 degrees S to the border with Perú. The major industrial activities are related to the copper mining industry. A measurement campaign was conducted during March and April 2006 to determine ambient PM10 and PM(2.5) concentrations in the city. The results showed significantly higher PM10 concentrations in the southern part of the city (117 microg/m3) compared with 79 and 80 (microg/m3) in the central and northern sites. By contrast, ambient PM2.5 concentrations had a more uniform spatial distribution across the city, around 20 (microg/m3). In order to conduct a source apportionment, daily PM10 and PM(2.5) samples were analyzed for elements by XRF. EPA's Positive Matrix Factorization software was used to interpret the results of the chemical compositions. The major source contributing to PM(2.5) at sites 1, 2 and 3, respectively are: (a) sulfates, with approximately 50% of PM2.5 concentrations at the three sites; (b) fugitive emissions from fertilizer storage and handling, with 16%, 21% and 10%; (c) Coal and residual oil combustion, with 15%, 15% and 4%; (d) Sea salt, 5%, 6% and 16%; (e) Copper ore processing, 4%, 5% and 15%; and (f) a mixed dust source with 11%, 7% and 4%. Results for PM10--at sites 1, 2 and 3, respectively--show that the major contributors are: (a) sea salt source with 36%, 32% and 36% of the PM10 concentration; (b) copper processing emissions mixed with airborne soil dust with 6.6%, 11.5% and 41%; (c) sulfates with 31%, 31% and 12%; (d) a mixed dust source with 16%, 12% and 10%, and (e) the fertilizer stockpile emissions, with 11%, 14% and 2% of the PM10 concentration. The high natural background of PM10 implies that major reductions in anthropogenic emissions of PM10 and SO2 would be required to attain ambient air quality standards for PM10; those reductions would curb down ambient PM(2.5) concentrations as well.

  17. Mexico City aerosol analysis during MILAGRO using high resolution aerosol mass spectrometry at the urban supersite (T0) - Part 1: Fine particle composition and organic source apportionment

    SciTech Connect

    Aiken, A.C.; Wang, J.; Salcedo, D.; Cubison, M. J.; Huffman, J. A.; DeCarlo, P. F.; Ulbrich, I. M.; Docherty, K. S.; Sueper, D.; Kimmel, J. R.; Worsnop, D. R.; Trimborn, A.; Northway, M.; Stone, E. A.; Schauer, J. J.; Volkamer, R. M.; Fortner, E.; de Foy, B.; Laskin, A.; Shutthanandan, V.; Zheng, J.; Zhang, R.; Gaffney, J.; Marley, N. A.; Paredes-Miranda, G.; Arnott, W. P.; Molina, L. T.; Sosa, G.; Jimenez, J. L.

    2009-09-01

    Submicron aerosol was analyzed during the MILAGRO field campaign in March 2006 at the T0 urban supersite in Mexico City with a High-Resolution Time-of-Flight Aerosol Mass Spectrometer (HR-ToF-AMS) and complementary instrumentation. Mass concentrations, diurnal cycles, and size distributions of inorganic and organic species are similar to results from the CENICA supersite in April 2003 with organic aerosol (OA) comprising about half of the fine PM mass. Positive Matrix Factorization (PMF) analysis of the high resolution OA spectra identified three major components: chemically-reduced urban primary emissions (hydrocarbon-like OA, HOA), oxygenated OA (OOA, mostly secondary OA or SOA), and biomass burning OA (BBOA) that correlates with levoglucosan and acetonitrile. BBOA includes several very large plumes from regional fires and likely also some refuse burning. A fourth OA component is a small local nitrogen-containing reduced OA component (LOA) which accounts for 9% of the OA mass but one third of the organic nitrogen, likely as amines. OOA accounts for almost half of the OA on average, consistent with previous observations. OA apportionment results from PMF-AMS are compared to the PM{sub 2.5} chemical mass balance of organic molecular markers (CMB-OMM, from GC/MS analysis of filters). Results from both methods are overall consistent. Both assign the major components of OA to primary urban, biomass burning/woodsmoke, and secondary sources at similar magnitudes. The 2006 Mexico City emissions inventory underestimates the urban primary PM{sub 2.5} emissions by a factor of {approx}4, and it is {approx}16 times lower than afternoon concentrations when secondary species are included. Additionally, the forest fire contribution is at least an order-of-magnitude larger than in the inventory.

  18. The importance of non-fossil sources in carbonaceous aerosols in a megacity of central China during the 2013 winter haze episode: A source apportionment constrained by radiocarbon and organic tracers

    NASA Astrophysics Data System (ADS)

    Liu, Junwen; Li, Jun; Vonwiller, Matthias; Liu, Di; Cheng, Hairong; Shen, Kaijun; Salazar, Gary; Agrios, Konstantinos; Zhang, Yanlin; He, Quanfu; Ding, Xiang; Zhong, Guangcai; Wang, Xinming; Szidat, Sönke; Zhang, Gan

    2016-11-01

    To determine the causes of a severe haze episode in January 2013 in China, a source apportionment of different carbonaceous aerosols (CAs) was conducted in a megacity in central China (Wuhan, Hubei Province) by using the measurements of radiocarbon and molecular organic tracers. Non-fossil sources (e.g., domestic biofuel combustion and biogenic emissions) were found to be responsible for 62% ± 5% and 26% ± 8% of organic carbon (OC) and elemental carbon (EC) components by mass, respectively. Non-fossil sources contributed 57% ± 4% to total CAs in this large-scale haze event, whereas fossil-fuel sources were less dominant (43% ± 4%). The CAs were composed of secondary organic carbon (SOC; 46% ± 10%), primary fossil-fuel carbon (29% ± 4%) and primary biomass-burning carbon (25% ± 10%). Although SOC was formed mainly from non-fossil sources (70% ± 4%), the role of fossil precursors was substantial (30% ± 4%), much higher than at the global scale. Combined measurement of organic tracers and radiocarbon showed that most non-fossil SOC was probably derived from biomass burning during this long-lasting haze episode in central China.

  19. A new approach based on a covariance structure model to source apportionment of indoor fine particles in Tokyo

    NASA Astrophysics Data System (ADS)

    Nitta, Hiroshi; Ichikawa, Masanori; Sato, Manabu; Konishi, Sadanori; Ono, Masaji

    A new receptor model is developed to estimate percent source contribution of indoor fine particles. Under the model, the covariance matrix of the elemental concentrations has a linear structure expressed as a weighted sum of known matrices and the percent contribution of each source is given by a function of the parameters involved. Given data, the percent source contributions are estimated using the information provided by the sample covariance matrix. Our approach makes it possible to selecta a set of sources that "best" describes the variation of the data. The standard errors of the percent source contribution estimates are evaluated by employing the bootstrap method. The proposed methods is applied to indoor air pollution data collected in the Tokyo Metropolitan area. Cigarette smoke, heavy oil combustion and diesel-powered automobiles were identified as important sources for both winter and summer data.

  20. Source apportionment of methane and nitrous oxide in California's San Joaquin Valley at CalNex 2010 via positive matrix factorization

    NASA Astrophysics Data System (ADS)

    Guha, A.; Gentner, D. R.; Weber, R. J.; Provencal, R.; Goldstein, A. H.

    2015-10-01

    Sources of methane (CH4) and nitrous oxide (N2O) were investigated using measurements from a site in southeast Bakersfield as part of the CalNex (California at the Nexus of Air Quality and Climate Change) experiment from mid-May to the end of June 2010. Typical daily minimum mixing ratios of CH4 and N2O were higher than daily minima that were simultaneously observed at a mid-oceanic background station (NOAA, Mauna Loa) by approximately 70 ppb and 0.5 ppb, respectively. Substantial enhancements of CH4 and N2O (hourly averages > 500 and > 7 ppb, respectively) were routinely observed, suggesting the presence of large regional sources. Collocated measurements of carbon monoxide (CO) and a range of volatile organic compounds (VOCs) (e.g., straight-chain and branched alkanes, cycloalkanes, chlorinated alkanes, aromatics, alcohols, isoprene, terpenes and ketones) were used with a positive matrix factorization (PMF) source apportionment method to estimate the contribution of regional sources to observed enhancements of CH4 and N2O. The PMF technique provided a "top-down" deconstruction of ambient gas-phase observations into broad source categories, yielding a seven-factor solution. We identified these emission source factors as follows: evaporative and fugitive; motor vehicles; livestock and dairy; agricultural and soil management; daytime light and temperature driven; non-vehicular urban; and nighttime terpene biogenics and anthropogenics. The dairy and livestock factor accounted for the majority of the CH4 (70-90 %) enhancements during the duration of experiments. The dairy and livestock factor was also a principal contributor to the daily enhancements of N2O (60-70 %). Agriculture and soil management accounted for ~ 20-25 % of N2O enhancements over a 24 h cycle, which is not surprising given that organic and synthetic fertilizers are known to be a major source of N2O. The N2O attribution to the agriculture and soil management factor had a high uncertainty in the

  1. Radiocarbon-Based Source Apportionment of the Water-Soluble Organic Carbon (wsoc) of Atmospheric Aerosols in South and East Asia

    NASA Astrophysics Data System (ADS)

    Kirillova, E. N.; Sheesley, R. J.; Andersson, A.; Gustafsson, O.; Safai, P. D.; Budhavant, K.; Rao, P. S.; Kang, E.; Han, J.; Lee, M.

    2011-12-01

    The air quality and regional climate in South and East Asia are considerably affected by atmospheric aerosols produced by anthropogenic activities. Recent studies have investigated the sources of the black carbon aerosol component in these regions. This study seeks to make progress in apportioning the sources of the water soluble organic carbon (WSOC) component, which makes up 20-65% of the carbonaceous aerosol mass in these areas. WSOC is important as it enhances the ability of particles to serve as cloud condensation nuclei (CCN) and, therefore, has an impact on regional climate and radiative forcing. Atmospheric particulate matter was collected during fifteen-month continuous sampling campaigns Jan 2008 - March 2009 at both the Maldives Climate Observatory at Hannimaadho (MCOH) and at the Sinhagad hilltop sampling site of the Indian Institute of Tropical Meteorology (SIN) in central-western India. The radiocarbon method is an ideal approach to identify fossil sources (14C "dead") compared to biogenic and biomass combustion products (with a contemporary 14C signal). WSOC is a large fraction of organic aerosols and its annual average contribution to TOC during 2008 is 26% at MCOH and 40% at SIN. There is a distinct seasonal variability in WSOC concentrations at both sites with high concentrations during the winter season (0.92±0.49μg m-3 at MCOH and 3.5±2.0μg m-3 at SIN) and very low concentrations during the summer monsoon season (0.08±0.04μg m-3 at MCOH and 0.27±0.20μg m-3 at SIN). The radiocarbon source apportionment of WSOC in winter dry season was similar at MCOH and SIN with 80-85% from biogenic/biomass combustion and the rest from fossil fuel precursors. For the rest of the year, the biogenic/biomass contribution to WSOC is higher at the Indian Ocean site (86-93%) compared to the Indian site (74-83%). In March 2011 the GoPoEx2011 intensive sampling campaign at the Gosan ABC Superstation, Jeju Island, South Korea was dedicated to study atmospheric

  2. Vertical profile, source apportionment, and toxicity of PAHs in sediment cores of a wharf near the coal-based steel refining industrial zone in Kaohsiung, Taiwan.

    PubMed

    Chen, Chih-Feng; Chen, Chiu-Wen; Ju, Yun-Ru; Dong, Cheng-Di

    2016-03-01

    Three sediment cores were collected from a wharf near a coal-based steel refining industrial zone in Kaohsiung, Taiwan. Analyses for 16 polycyclic aromatic hydrocarbons (PAHs) of the US Environmental Protection Agency priority list in the core sediment samples were conducted using gas chromatography-mass spectrometry. The vertical profiles of PAHs in the core sediments were assessed, possible sources and apportionment were identified, and the toxicity risk of the core sediments was determined. The results from the sediment analyses showed that total concentrations of the 16 PAHs varied from 11774 ± 4244 to 16755 ± 4593 ng/g dry weight (dw). Generally, the vertical profiles of the PAHs in the sediment cores exhibited a decreasing trend from the top to the lower levels of the S1 core and an increasing trend of PAHs from the top to the lower levels of the S2 and S3 cores. Among the core sediment samples, the five- and six-ring PAHs were predominantly in the S1 core, ranging from 42 to 54 %, whereas the composition of the PAHs in the S2 and S3 cores were distributed equally across three groups: two- and three-ring, four-ring, and five- and six-ring PAHs. The results indicated that PAH contamination at the site of the S1 core had a different source. The molecular indices and principal component analyses with multivariate linear regression were used to determine the source contributions, with the results showing that the contributions of coal, oil-related, and vehicle sources were 38.6, 35.9, and 25.5 %, respectively. A PAH toxicity assessment using the mean effect range-median quotient (m-ERM-q, 0.59-0.79), benzo[a]pyrene toxicity equivalent (TEQ(carc), 1466-1954 ng TEQ/g dw), and dioxin toxicity equivalent (TEQ(fish), 3036-4174 pg TEQ/g dw) identified the wharf as the most affected area. The results can be used for regular monitoring, and future pollution prevention and management should target the coal-based industries in this region for pollution reduction.

  3. Bayesian nitrate source apportionment to individual groundwater wells in the Central Valley by use of elemental and isotopic tracers

    USGS Publications Warehouse

    Ransom, Katherine M; Grote, Mark N.; Deinhart, Amanda; Eppich, Gary; Kendall, Carol; Sanborn, Matthew E.; Sounders, A. Kate; Wimpenny, Joshua; Yin, Qing-zhu; Young, Megan B.; Harter, Thomas

    2016-01-01

    Groundwater quality is a concern in alluvial aquifers that underlie agricultural areas, such as in the San Joaquin Valley of California. Shallow domestic wells (less than 150 m deep) in agricultural areas are often contaminated by nitrate. Agricultural and rural nitrate sources include dairy manure, synthetic fertilizers, and septic waste. Knowledge of the relative proportion that each of these sources contributes to nitrate concentration in individual wells can aid future regulatory and land management decisions. We show that nitrogen and oxygen isotopes of nitrate, boron isotopes, and iodine concentrations are a useful, novel combination of groundwater tracers to differentiate between manure, fertilizers, septic waste, and natural sources of nitrate. Furthermore, in this work, we develop a new Bayesian mixing model in which these isotopic and elemental tracers were used to estimate the probability distribution of the fractional contributions of manure, fertilizers, septic waste, and natural sources to the nitrate concentration found in an individual well. The approach was applied to 56 nitrate-impacted private domestic wells located in the San Joaquin Valley. Model analysis found that some domestic wells were clearly dominated by the manure source and suggests evidence for majority contributions from either the septic or fertilizer source for other wells. But, predictions of fractional contributions for septic and fertilizer sources were often of similar magnitude, perhaps because modeled uncertainty about the fraction of each was large. For validation of the Bayesian model, fractional estimates were compared to surrounding land use and estimated source contributions were broadly consistent with nearby land use types.

  4. Bayesian nitrate source apportionment to individual groundwater wells in the Central Valley by use of elemental and isotopic tracers

    NASA Astrophysics Data System (ADS)

    Ransom, Katherine M.; Grote, Mark N.; Deinhart, Amanda; Eppich, Gary; Kendall, Carol; Sanborn, Matthew E.; Souders, A. Kate; Wimpenny, Joshua; Yin, Qing-zhu; Young, Megan; Harter, Thomas

    2016-07-01

    Groundwater quality is a concern in alluvial aquifers that underlie agricultural areas, such as in the San Joaquin Valley of California. Shallow domestic wells (less than 150 m deep) in agricultural areas are often contaminated by nitrate. Agricultural and rural nitrate sources include dairy manure, synthetic fertilizers, and septic waste. Knowledge of the relative proportion that each of these sources contributes to nitrate concentration in individual wells can aid future regulatory and land management decisions. We show that nitrogen and oxygen isotopes of nitrate, boron isotopes, and iodine concentrations are a useful, novel combination of groundwater tracers to differentiate between manure, fertilizers, septic waste, and natural sources of nitrate. Furthermore, in this work, we develop a new Bayesian mixing model in which these isotopic and elemental tracers were used to estimate the probability distribution of the fractional contributions of manure, fertilizers, septic waste, and natural sources to the nitrate concentration found in an individual well. The approach was applied to 56 nitrate-impacted private domestic wells located in the San Joaquin Valley. Model analysis found that some domestic wells were clearly dominated by the manure source and suggests evidence for majority contributions from either the septic or fertilizer source for other wells. But, predictions of fractional contributions for septic and fertilizer sources were often of similar magnitude, perhaps because modeled uncertainty about the fraction of each was large. For validation of the Bayesian model, fractional estimates were compared to surrounding land use and estimated source contributions were broadly consistent with nearby land use types.

  5. Source Apportionment and Elemental Composition of PM2.5 and PM10 in Jeddah City, Saudi Arabia

    PubMed Central

    Khodeir, Mamdouh; Shamy, Magdy; Alghamdi, Mansour; Zhong, Mianhua; Sun, Hong; Costa, Max; Chen, Lung-Chi; Maciejczyk, Polina

    2014-01-01

    This paper presents the first comprehensive investigation of PM2.5 and PM10 composition and sources in Saudi Arabia. We conducted a multi-week multiple sites sampling campaign in Jeddah between June and September, 2011, and analyzed samples by XRF. The overall mean mass concentration was 28.4 ± 25.4 μg/m3 for PM2.5 and 87.3 ± 47.3 μg/m3 for PM10, with significant temporal and spatial variability. The average ratio of PM2.5/PM10 was 0.33. Chemical composition data were modeled using factor analysis with varimax orthogonal rotation to determine five and four particle source categories contributing significant amount of for PM2.5 and PM10 mass, respectively. In both PM2.5 and PM10 sources were (1) heavy oil combustion characterized by high Ni and V; (2) resuspended soil characterized by high concentrations of Ca, Fe, Al, and Si; and (3) marine aerosol. The two other sources in PM2.5 were (4) Cu/Zn source; (5) traffic source identified by presence of Pb, Br, and Se; while in PM10 it was a mixed industrial source. To estimate the mass contributions of each individual source category, the CAPs mass concentration was regressed against the factor scores. Cumulatively, resuspended soil and oil combustion contributed 77 and 82% mass of PM2.5 and PM10, respectively. PMID:24634602

  6. Bayesian Nitrate Source Apportionment to Individual Groundwater Wells in the Central Valley by Use of Elemental and Isotopic Tracers

    NASA Astrophysics Data System (ADS)

    Ransom, K.; Grote, M. N.; Deinhart, A.; Eppich, G.; Kendall, C.; Sanborn, M.; Souders, K.; Wimpenny, J.; Yin, Q. Z.; Young, M. B.; Harter, T.

    2015-12-01

    Groundwater quality is a concern in alluvial aquifers that underlie agricultural areas, such as in the San Joaquin Valley of California. Nitrate from fertilizers and animal waste can leach to groundwater and contaminate drinking water resources. Dairy manure and synthetic fertilizers are prevailing sources of nitrate in groundwater for the San Joaquin Valley with septic waste contributing as a major source in some areas. The rural population in the San Joaquin Valley relies almost exclusively on shallow domestic wells (less than 150 m deep), of which many have been affected by nitrate. Knowledge of the proportion of each of the three main nitrate sources (manure, synthetic fertilizer, and septic waste) contributing to individual well nitrate can aid future regulatory decisions. Mixing models quantify the proportional contributions of sources to a mixture by using the concentration of conservative tracers within each source as a source signature. Deterministic mixing models are common, but do not allow for variability in the tracer source concentration or overlap of tracer concentrations between sources. In contrast, Bayesian mixing models treat source contributions probabilistically, building statistical variation into the inferences for each well. The authors developed a Bayesian mixing model on a pilot network of 56 private domestic wells in the San Joaquin Valley for which nitrogen, oxygen, and boron isotopes as well as nitrate and iodine were measured. Nitrogen, oxygen, and boron isotopes as well as iodine can be used as tracers to differentiate between manure, fertilizers, septic waste, and natural sources of nitrate (which can contribute nitrate in concentrations up to 4 mg/L). In this work, the isotopic and elemental tracers were used to estimate the proportional contribution of manure, fertilizers, septic waste, and natural sources to overall groundwater nitrate concentration in individual wells. Prior distributions for the four tracers for each of the four

  7. Source apportionment of PM2.5 chemically speciated mass and particle number concentrations in New York City

    NASA Astrophysics Data System (ADS)

    Masiol, M.; Hopke, P. K.; Felton, H. D.; Frank, B. P.; Rattigan, O. V.; Wurth, M. J.; LaDuke, G. H.

    2017-01-01

    The major sources of fine particulate matter (PM2.5) in New York City (NYC) were apportioned by applying positive matrix factorization (PMF) to two different sets of particle characteristics: mass concentrations using chemical speciation data and particle number concentrations (PNC) using number size distribution, continuously monitored gases, and PM2.5 data. Post-processing was applied to the PMF results to: (i) match with meteorological data, (ii) use wind data to detect the likely locations of the local sources, and (iii) use concentration weighted trajectory models to assess the strength of potential regional/transboundary sources. Nine sources of PM2.5 mass were apportioned and identified as: secondary ammonium sulfate, secondary ammonium nitrate, road traffic exhaust, crustal dust, fresh sea-salt, aged sea-salt, biomass burning, residual oil/domestic heating and zinc. The sources of PNC were investigated using hourly average number concentrations in six size bins, gaseous air pollutants, mass concentrations of PM2.5, particulate sulfate, OC, and EC. These data were divided into 3 periods indicative of different seasonal conditions. Five sources were resolved for each period: secondary particles, road traffic, NYC background pollution (traffic and oil heating largely in Manhattan), nucleation and O3-rich aerosol. Although traffic does not account for large amounts of PM2.5 mass, it was the main source of particles advected from heavily trafficked zones. The use of residual oil had limited impacts on PM2.5 mass but dominates PNC in cold periods.

  8. Nitrate source apportionment using a combined dual isotope, chemical and bacterial property, and Bayesian model approach in river systems

    NASA Astrophysics Data System (ADS)

    Xia, Yongqiu; Li, Yuefei; Zhang, Xinyu; Yan, Xiaoyuan

    2017-01-01

    Nitrate (NO3-) pollution is a serious problem worldwide, particularly in countries with intensive agricultural and population activities. Previous studies have used δ15N-NO3- and δ18O-NO3- to determine the NO3- sources in rivers. However, this approach is subject to substantial uncertainties and limitations because of the numerous NO3- sources, the wide isotopic ranges, and the existing isotopic fractionations. In this study, we outline a combined procedure for improving the determination of NO3- sources in a paddy agriculture-urban gradient watershed in eastern China. First, the main sources of NO3- in the Qinhuai River were examined by the dual-isotope biplot approach, in which we narrowed the isotope ranges using site-specific isotopic results. Next, the bacterial groups and chemical properties of the river water were analyzed to verify these sources. Finally, we introduced a Bayesian model to apportion the spatiotemporal variations of the NO3- sources. Denitrification was first incorporated into the Bayesian model because denitrification plays an important role in the nitrogen pathway. The results showed that fertilizer contributed large amounts of NO3- to the surface water in traditional agricultural regions, whereas manure effluents were the dominant NO3- source in intensified agricultural regions, especially during the wet seasons. Sewage effluents were important in all three land uses and exhibited great differences between the dry season and the wet season. This combined analysis quantitatively delineates the proportion of NO3- sources from paddy agriculture to urban river water for both dry and wet seasons and incorporates isotopic fractionation and uncertainties in the source compositions.

  9. Levels of total suspended particulate matter and major trace elements in Kosovo: a source identification and apportionment study.

    PubMed

    Arditsoglou, Anastasia; Samara, Constantini

    2005-04-01

    Concentration levels of total suspended particles (TSP) and 27 major, minor and trace elemental components were determined at four sites in Kosovo through a 1-year survey (January-December 2002). Ambient concentrations were evaluated in comparison to limit values. The origin of elemental TSP constituents was investigated by calculating enrichment factors and diagnostic ratios. Multivariate statistics, such as hierarchical cluster analysis and factor analysis, were also employed to identify emission sources. A multivariate statistical receptor model (Absolute Principal Component Analysis, APCA) was applied to quantify source contributions. Soil dust, cement production, vehicular emissions, brake wear, and fuel combustion were identified as major sources with variable contributions at the four sampling sites.

  10. Concentration profiles, source apportionment and risk assessment of polycyclic aromatic hydrocarbons (PAHs) in dumpsite soils from Agbogbloshie e-waste dismantling site, Accra, Ghana.

    PubMed

    Daso, Adegbenro P; Akortia, Eric; Okonkwo, Jonathan O

    2016-06-01

    methodological approaches for PAH source apportionment, including the use of molecular diagnostic ratios, mostly implicated pyrogenic processes as the main sources of PAHs into the investigated dumpsite soils. Furthermore, their compositional profiles across the sampling sites also suggest similar sources of PAHs into the dumpsite soil.

  11. Composition and source apportionment of PM1 at urban site Kanpur in India using PMF coupled with CBPF

    NASA Astrophysics Data System (ADS)

    Rai, Pragati; Chakraborty, Abhishek; Mandariya, Anil Kumar; Gupta, Tarun

    2016-09-01

    This study addresses the three major questions: (1) what are the emission sources of PM1 which are affecting the study area; (2) where do these emission sources come from; and (3) is there any temporal variation in the emission sources. To address these issues, two advanced statistical methods are described in this paper. Identification of emission sources was performed by EPA PMF (v 5.0) and to understand the temporal variability, sampling was done for three winter seasons 2008-09, 2009-10 and 2011-12 within Kanpur city. To identify the possible source directions, Conditional Bivariate Probability function (CBPF) was used. The average PM1 concentration was higher in 2008-09 followed by 2011-12 and 2009-10 winter seasons. 2008-09 winter showed sources such as secondary sources mixed with power plant emission (42.8%), industrial emission (32.3%), coal combustion, brick kilns and vehicular emission (13.2%) and residual oil combustion and road dust (11.7%). The major contributors during winter season 2009-10 were secondary sources (33.1%), biomass burning (23.3%), heavy oil combustion (13%), vehicular emission mixed with crustal dust (11.3%), leather tanning industries (10.3%), industrial emission (4%), coal combustion and brick kilns (3.4%) and solid waste burning and incineration (1.5%) compared to secondary sources mixed with biomass burning (42.3%), industrial emission and crustal dust (35.1%) and vehicular emission and brick kilns (22.6%) during 2011-12 winter season. PMF model revealed that secondary sources were the main contributors for all the three winter seasons followed by biomass burning and power plant emission. The results of CBPF analysis agreed well with the locations of known local point sources., e.g. in the case of industrial emissions, the maximum probability was in the direction between NES direction where almost all the major industries are located in and around Kanpur while in the opposite direction the probability of biomass burning was high

  12. Size-resolved source apportionment of ambient particles by positive matrix factorization at Gosan background site in East Asia

    NASA Astrophysics Data System (ADS)

    Han, J. S.; Moon, K. J.; Lee, S. J.; Kim, Y. J.; Ryu, S. Y.; Cliff, S. S.; Yi, S. M.

    2006-01-01

    Size- and time-resolved aerosol samples were collected using an eight-stage Davis rotating unit for monitoring (DRUM) sampler from 29 March to 29 May in 2002 at Gosan, Jeju Island, Korea, which is one of the representative background sites in East Asia. These samples were analyzed using synchrotron X-ray fluorescence for 3-h average concentrations of 19 elements consisting of S, Si, Al, Fe, Ca, Cl, Cu, Zn, Ti, K, Mn, Pb, Ni, V, Se, As, Rb, Cr, Br. The size-resolved data sets were then analyzed using the positive matrix factorization (PMF) technique in order to identify possible sources and estimate their contribution to particulate matter mass. PMF analysis uses the uncertainty of the measured data to provide an optimal weighting. Fifteen sources were resolved in eight size ranges (0.07~12 μm) and included continental soil, local soil, sea salt, biomass/biofuel burning, coal combustion, oil heating furnace, residual oil fired boiler, municipal incineration, nonferrous metal source, ferrous metal source, gasoline vehicle, diesel vehicle, copper smelter and volcanic emission. PMF analysis of size-resolved source contributions showed that natural sources represented by local soil, sea salt and continental soil contributed about 79% to the predicted primary particulate matter (PM) mass in the coarse size range (1.15~12 μm). On the other hand, anthropogenic sources such as coal combustion and biomass/biofuel burning contributed about 60% in the fine size range (0.56~2.5 μm). The diesel vehicle source contributed the most in the ultra-fine size range (0.07~0.56 μm) and was responsible for about 52% of the primary PM mass.

  13. Metal enrichment and lead isotope analysis for source apportionment in the urban dust and rural surface soil.

    PubMed

    Yu, Yang; Li, Yingxia; Li, Ben; Shen, Zhenyao; Stenstrom, Michael K

    2016-09-01

    To understand the metal accumulation in the environment and identify its sources, 29 different metal contents and lead (Pb) isotope ratios were determined for 40 urban dust samples, 36 surface soil samples, and one river sediment sample collected in the municipality of Beijing, China. Results showed that cadmium, copper (Cu), mercury, Pb, antimony (Sb), and zinc demonstrated to be the typical urban contaminants and mostly influenced by the adjacent human activities with higher content to background ratios and SD values. Among the 29 metal elements investigated, Cu and Sb were found to be the most distinct elements that were highly affected by the developing level and congestion status of the cities with much higher contents in dust in more developed and congested cities. There was a relatively wider range of Pb isotope ratios of country surface soil than those of urban dust. The results of source identification based on Pb isotope ratios showed that coal combustion was the first largest Pb source and vehicle exhaust was the second largest source. The sum of them accounted for 74.6% mass proportion of overall Pb pollution on average. The surface soil sample collected at an iron mine had the highest (204)Pb/(206)Pb, (207)Pb/(206)Pb, and (208)Pb/(206)Pb ratios indicating ore had much higher ratios than other sources. The fine particle subsamples had higher (204)Pb/(206)Pb, (207)Pb/(206)Pb, and (208)Pb/(206)Pb ratios than the coarse particle subsamples indicating more anthropogenic sources of coal combustion and vehicle exhaust for fine particles and more background influence for coarse particles. These results help with pinpointing the major Pb sources and applying suitable measures for the target sources.

  14. Concentrations and source apportionment of PM10 and associated elemental and ionic species in a lignite-burning power generation area of southern Greece.

    PubMed

    Argyropoulos, G; Grigoratos, Th; Voutsinas, M; Samara, C

    2013-10-01

    Ambient concentrations of PM10 and associated elemental and ionic species were measured over the cold and the warm months of 2010 at an urban and two rural sites located in the lignite-fired power generation area of Megalopolis in Peloponnese, southern Greece. The PM10 concentrations at the urban site (44.2 ± 33.6 μg m(-3)) were significantly higher than those at the rural sites (23.7 ± 20.4 and 22.7 ± 26.9 μg m(-3)). Source apportionment of PM10 and associated components was accomplished by an advanced computational procedure, the robotic chemical mass balance model (RCMB), using chemical profiles for a variety of local fugitive dust sources (power plant fly ash, flue gas desulfurization wet ash, feeding lignite, infertile material from the opencast mines, paved and unpaved road dusts, soil), which were resuspended and sampled through a PM10 inlet onto filters and then chemically analyzed, as well as of other common sources such as vehicular traffic, residential oil combustion, biomass burning, uncontrolled waste burning, marine aerosol, and secondary aerosol formation. Geological dusts (road/soil dust) were found to be major PM10 contributors in both the cold and warm periods of the year, with average annual contribution of 32.6 % at the urban site vs. 22.0 and 29.0 % at the rural sites. Secondary aerosol also appeared to be a significant source, contributing 22.1 % at the urban site in comparison to 30.6 and 28.7 % at the rural sites. At all sites, the contribution of biomass burning was most significant in winter (28.2 % at the urban site vs. 14.6 and 24.6 % at the rural sites), whereas vehicular exhaust contribution appeared to be important mostly in the summer (21.9 % at the urban site vs. 11.5 and 10.5 % at the rural sites). The highest contribution of fly ash (33.2 %) was found at the rural site located to the north of the power plants during wintertime, when winds are favorable. In the warm period, the highest contribution of fly ash was found at the

  15. Spatial/temporal variations and source apportionment of VOCs monitored at community scale in an urban area.

    PubMed

    Yu, Chang Ho; Zhu, Xianlei; Fan, Zhi-hua

    2014-01-01

    This study aimed to characterize spatial/temporal variations of ambient volatile organic compounds (VOCs) using a community-scale monitoring approach and identify the main sources of concern in Paterson, NJ, an urban area with mixed sources of VOCs. VOC samples were simultaneously collected from three local source-dominated (i.e., commercial, industrial, and mobile) sites in Paterson and one background site in Chester, NJ (located ∼58 km southwest of Paterson). Samples were collected using the EPA TO-15 method from midnight to midnight, one in every sixth day over one year. Among the 60 analyzed VOCs, ten VOCs (acetylene, benzene, dichloromethane, ethylbenzene, methyl ethyl ketone, styrene, toluene, m,p-xylene, o-xylene, and p-dichlorobenzene) were selected to examine their spatial/temporal variations. All of the 10 VOCs in Paterson were significantly higher than the background site (p<0.01). Ethylbenzene, m,p-xylene, o-xylene, and p-dichlorobenzene measured at the commercial site were significantly higher than the industrial/mobile sites (p<0.01). Seven VOCs (acetylene, benzene, dichloromethane, methyl ethyl ketone, styrene, toluene, and p-dichlorobenzene) were significantly different by season (p<0.05), that is, higher in cold seasons than in warm seasons. In addition, dichloromethane, methyl ethyl ketone, and toluene were significantly higher on weekdays than weekend days (p<0.05). These results are consistent with literature data, indicating the impact of anthropogenic VOC sources on air pollution in Paterson. Positive Matrix Factorization (PMF) analysis was applied for 24-hour integrated VOC measurements in Paterson over one year and identified six contributing factors, including motor vehicle exhausts (20%), solvents uses (19%), industrial emissions (16%), mobile+stationery sources (12%), small shop emissions (11%), and others (22%). Additional locational analysis confirmed the identified sources were well matched with point sources located upwind in

  16. [Pollution Level and Source Apportionment of Atmospheric Particles PM₂.₅ in Southwest Suburb of Chengdu in Spring].

    PubMed

    Lin, Yu; Ye, Zhi-xiang; Yang, Huai-jin; Zhang, Ju; Yin, Wei-wen; Li, Xiao-fen

    2016-05-15

    In order to understand the characteristics of PM₂.₅ pollution in the atmosphere of Chengdu southwest suburb, PM₂.₅ particles in Chengdu southwest suburb were collected and analyzed from March 18 to March 31st, 2015. The results showed that the daily average concentration of PM₂.₅ in the southwest suburb of Chengdu reached 121.21 µg · m⁻³, and the average daily concentration of 24 samples in 31 PM₂.₅ samples was over 75 µg · m⁻³, the daily excessive rate was 77%, indicating the PM₂.₅ pollution in the study area was serious in March. When studying the relationship between atmospheric and meteorological factors, it was found that there was a significant index correlation between PM₂.₅ concentration and atmospheric visibility, and it had a positive correlation with temperature and humidity, but the correlation was not obvious. NH₄⁺ (16.24%), SO₄²- (12.58%) and NO₃⁻ (9.91%) were dominant in PM₂.₅ The ratio of NO₃⁻/SO₄²⁻ was 0.77, which indicated that the pollution of stationary sources in the southwest suburb was more severe than that of mobile sources. Organic carbon (OC)/elemental carbon (EC) ratios were higher than 2, which indicated the existence of second organic carbon (SOC). Using OC/EC ratio method to estimate the concentration of SOC, it was found that the average concentration of SOC in the southwest suburb of Chengdu in March was 3.49 µ · m⁻³, and the contribution rate of OC was 20.6%, which showed that the main source of OC in the southwest suburb of Chengdu was primary discharge. The correlation analysis of OC and EC showed that the correlation coefficient reached 0.95, indicating that the OC and EC sources were similar and relatively stable, and there was a great impact of local source emissions on Chengdu southwest suburb in spring, and primary discharge played a dominant role, while the contribution of SOC to OC was relatively small, which was consistent with the SOC characteristics obtained

  17. Spatial/Temporal Variations and Source Apportionment of VOCs Monitored at Community Scale in an Urban Area

    PubMed Central

    Yu, Chang Ho; Zhu, Xianlei; Fan, Zhi-hua

    2014-01-01

    This study aimed to characterize spatial/temporal variations of ambient volatile organic compounds (VOCs) using a community-scale monitoring approach and identify the main sources of concern in Paterson, NJ, an urban area with mixed sources of VOCs. VOC samples were simultaneously collected from three local source-dominated (i.e., commercial, industrial, and mobile) sites in Paterson and one background site in Chester, NJ (located ∼58 km southwest of Paterson). Samples were collected using the EPA TO-15 method from midnight to midnight, one in every sixth day over one year. Among the 60 analyzed VOCs, ten VOCs (acetylene, benzene, dichloromethane, ethylbenzene, methyl ethyl ketone, styrene, toluene, m,p-xylene, o-xylene, and p-dichlorobenzene) were selected to examine their spatial/temporal variations. All of the 10 VOCs in Paterson were significantly higher than the background site (p<0.01). Ethylbenzene, m,p-xylene, o-xylene, and p-dichlorobenzene measured at the commercial site were significantly higher than the industrial/mobile sites (p<0.01). Seven VOCs (acetylene, benzene, dichloromethane, methyl ethyl ketone, styrene, toluene, and p-dichlorobenzene) were significantly different by season (p<0.05), that is, higher in cold seasons than in warm seasons. In addition, dichloromethane, methyl ethyl ketone, and toluene were significantly higher on weekdays than weekend days (p<0.05). These results are consistent with literature data, indicating the impact of anthropogenic VOC sources on air pollution in Paterson. Positive Matrix Factorization (PMF) analysis was applied for 24-hour integrated VOC measurements in Paterson over one year and identified six contributing factors, including motor vehicle exhausts (20%), solvents uses (19%), industrial emissions (16%), mobile+stationery sources (12%), small shop emissions (11%), and others (22%). Additional locational analysis confirmed the identified sources were well matched with point sources located upwind in

  18. Source apportionment of PAHs and n-alkanes in respirable particles in Tehran, Iran by wind sector and vertical profile.

    PubMed

    Moeinaddini, Mazaher; Esmaili Sari, Abbas; Riyahi bakhtiari, Alireza; Chan, Andrew Yiu-Chung; Taghavi, Seyed Mohammad; Hawker, Darryl; Connell, Des

    2014-06-01

    The vertical concentration profiles and source contributions of polycyclic aromatic hydrocarbons (PAHs) and n-alkanes in respirable particle samples (PM4) collected at 10, 100, 200 and 300-m altitude from the Milad Tower of Tehran, Iran during fall and winter were investigated. The average concentrations of total PAHs and total n-alkanes were 16.7 and 591 ng/m(3), respectively. The positive matrix factorization (PMF) model was applied to the chemical composition and wind data to apportion the contributing sources. The five PAH source factors identified were: 'diesel' (56.3% of total PAHs on average), 'gasoline' (15.5%), 'wood combustion, and incineration' (13%), 'industry' (9.2%), and 'road soil particle' (6.0%). The four n-alkane source factors identified were: 'petrogenic' (65% of total n-alkanes on average), 'mixture of petrogenic and biomass burning' (15%), 'mixture of biogenic and fossil fuel' (11.5%), and 'biogenic' (8.5%). Source contributions by wind sector were also estimated based on the wind sector factor loadings from PMF analysis. Directional dependence of sources was investigated using the conditional probability function (CPF) and directional relative strength (DRS) methods. The calm wind period was found to contribute to 4.4% of total PAHs and 5.0% of total n-alkanes on average. Highest average concentrations of PAHs and n-alkanes were found in the 10 and 100 m samples, reflecting the importance of contributions from local sources. Higher average concentrations in the 300 m samples compared to those in the 200 m samples may indicate contributions from long-range transport. The vertical profiles of source factors indicate the gasoline and road soil particle-associated PAHs, and the mixture from biogenic and fossil fuel source-associated n-alkanes were mostly from local emissions. The smaller average contribution of diesel-associated PAHs in the lower altitude samples also indicates that the restriction of diesel-fueled vehicle use in the central area

  19. Chemical composition of PM2.5 particles in Salamanca, Guanajuato Mexico: Source apportionment with receptor models

    NASA Astrophysics Data System (ADS)

    Herrera Murillo, Jorge; Campos Ramos, Arturo; Ángeles García, Felipe; Blanco Jiménez, Salvador; Cárdenas, Beatriz; Mizohata, Akira

    2012-04-01

    The National Institute of Ecology, through Management General for Environmental Research and Training (DGCENICA) carried out a sampling campaign where a total of 21 elements were determined in 140 PM2.5 samples from one sampling site located in the city of Salamanca, Guanajuato-Mexico between November 2006 and November 2007. The annual average PM2.5 concentration was 45 μg/m3 almost three times the Mexican Annual standard for PM2.5. Mineral, organic and elemental carbon were the most important components present in particles PM2.5. Two advanced receptor models, UNMIX and positive matrix factorization (PMF) were used for PM2.5 source identification. Four and six sources were identified by UNMIX and PMF, respectively, from a combined dataset including 15 chemical species. Source categories were determined based on both, component abundances in the source profiles, and their temporal characteristics. Overall, different sources were identified as the major contributors: heavy fuels combustion, traditional brick production-agricultural burning, crustal, road traffic and secondary organic aerosols.

  20. Source apportionment of PAHs and n-alkanes bound to PM1 collected near the Venice highway.

    PubMed

    Valotto, Gabrio; Rampazzo, Giancarlo; Gonella, Francesco; Formenton, Gianni; Ficotto, Silvia; Giraldo, Giorgia

    2017-04-01

    n-Alkanes and polycyclic aromatic hydrocarbons (PAHs) bound to atmospheric particulate matter (PM1) were investigated in a traffic site located in an urban area of Venice Province (Eastern Po Valley, Italy) during the cold season. Considering the critical situation affecting the Veneto Region concerning the atmospheric pollution and the general lack of information on PM1 composition and emission in this area, this experimental study aims at determining the source profile, their relative contributions and the dispersion of finer particles. Four sources were identified and quantified using the Positive Matrix Factorization receptor model: (1) mixed combustions related to the residential activities, (2) agricultural biomass burning in addition to the resuspension of anthropogenic and natural debris carried by the wind, (3) gasoline and (4) diesel traffic-related combustions. The role of local atmospheric circulation was also investigated to identify the pollutant sources.

  1. Distribution and source apportionment of polycyclic aromatic hydrocarbons in soils and leaves from high-altitude mountains in southwestern china.

    PubMed

    Shi, Bingfang; Wu, Qilin; Ouyang, Huixiang; Liu, Xixiang; Ma, Bo; Zuo, Weiyuan; Chen, Shengyu

    2014-11-01

    Several studies have investigated the distribution patterns and geographic sources of polycyclic aromatic hydrocarbons (PAHs) in mountainous areas. Little is known about how different sources contribute to PAH concentrations at different elevations along mountain slopes. To estimate the distribution and sources of PAHs at different altitudes in mountainous areas of southwestern China, samples of soils and leaves from trees were collected from 1000 to 1500 m asl in the Dawangling forest and analyzed for PAHs. Total PAH concentrations ranged from 93.9 to 802.3 ng g (average, 252.3 ng g) in soils and from 4.1 to 100.9 ng g (average, 23.1 ng g) in leaves. Our results suggest that soil PAH levels in the study area could be classified as "weakly contaminated." The PAH levels in leaves from the Dawangling forest were lower than those found in Himalayan spruce needles from the central Himalayas in China and from an agricultural station in southern England. Total PAHs in the Dawangling forest soils increased with elevation, primarily due to the low-molecular-weight PAHs, which accumulated in samples from higher altitudes. In contrast, high-molecular-weight PAHs were inversely related to or unrelated to elevation. The PAH profiles were similar in soils and leaves from all mountainous regions. Diagnostic ratios showed that the PAHs in soils at different altitudes were from different pollution emission sources; therefore, PAHs in the entire study area were probably derived from mixed sources. Cluster analyses confirmed that liquefied petroleum gas, coal/wood combustion, and petroleum combustion were likely the predominant PAH sources in this region.

  2. Particulate pollution in urban Chongqing of southwest China: Historical trends of variation, chemical characteristics and source apportionment.

    PubMed

    Chen, Yuan; Xie, Shao-Dong; Luo, Bin; Zhai, Chong-Zhi

    2017-04-15

    Chongqing, the largest megacity in southwest China, faces serious aerosol pollution but lacks information on particle characteristics and its sources. Official data released by Chongqing Environmental Protection Bureau demonstrated that urban PM10 concentrations decreased remarkably from 150μgm(-3) in 2000 to 90μgm(-3) in 2012. However, only several peer-reviewed studies paid attention to local fine particle (PM2.5) pollution. In the study, PM2.5 samples were obtained and subjected to chemical analysis in an urban site of the city during 2012 to 2013. The annual mean PM10 and PM2.5 concentrations in urban Chongqing were 103.9±52.5 and 75.4±42.2μgm(-3), respectively. PM2.5 showed a distinct seasonality of high concentration in winter and similar levels in other seasons. The average OC/EC (organic carbon/element carbon) ratio was 3.7 with more high-OC/EC ratio sources contribution in autumn and winter. The varying sources and formation mechanisms resulted in SO4(2-) and NH4(+) peaks in both summer and winter, whereas high nitrate concentration was only observed in winter. In the average mass closure, PM2.5 was composed of 23.0% SO4(2-), 11.7% NO3(-), 10.9% NH4(+), 30.8% OM (organic matter), 5.2% EC, 8.2% mineral dust, 0.6% TEO (trace elements), 1.0% Cl(-) and 1.1% K(+), while exhibiting large seasonal variability. Using positive matrix factorization (PMF), six sources were apportioned in PM2.5: secondary inorganic aerosols, coal combustion, other industrial pollution, soil dust, vehicular emission, and metallurgical industry. The annual mean contribution of above sources to PM2.5 was 37.5, 22.0, 17.5, 11.0, 9.8 and 2.2%, respectively. Coal combustion was identified by As tracer and dominated the primary sources of PM2.5, while the two different industrial sources were characterized by Cr and Mo, Co, Ni, and Se, respectively. The study is of great importance in characterizing the historical trends, current chemical characteristics and sources of fine particles in

  3. Spatial Distribution, Air-Water Fugacity Ratios and Source Apportionment of Polychlorinated Biphenyls in the Lower Great Lakes Basin.

    PubMed

    Khairy, Mohammed; Muir, Derek; Teixeira, Camilla; Lohmann, Rainer

    2015-12-01

    Polychlorinated biphenyls (PCBs) continue to be contaminants of concern across the Great Lakes. It is unclear whether current concentrations are driven by ongoing primary emissions from their original uses, or whether ambient PCBs are dominated by their environmental cycling. Freely dissolved PCBs in air and water were measured using polyethylene passive samplers across Lakes Erie and Ontario during summer and fall, 2011, to investigate their spatial distribution, determine and apportion their sources and to asses their air-water exchange gradients. Average gaseous and freely dissolved ∑29 PCB concentrations ranged from 5.0 to 160 pg/m(3) and 2.0 to 55 pg/L respectively. Gaseous concentrations were significantly correlated (R(2) = 0.80) with the urban area within a 3-20 km radius. Fugacity ratios indicated that the majority of PCBs are volatilizing from the water thus acting as a secondary source for the atmosphere. Dissolved PCBs were probably linked to PCB emissions from contaminated sites and areas of concern. Positive matrix factorization indicated that although volatilized Aroclors (gaseous PCBs) and unaltered Aroclors (dissolved PCBs) dominate in some samples, ongoing non-Aroclor sources such as paints/pigments (PCB 11) and coal/wood combustion showed significant contributions across the lower Great Lakes. Accordingly, control strategies should give further attention to PCBs emitted from current use sources.

  4. THE WORKSHOP ON THE SOURCE APPORTIONMENT OF PM HEALTH EFFECTS: INTER-COMPARISON OF RESULTS AND IMPLICATIONS

    EPA Science Inventory

    While the association between exposure to ambient fine particulate matter mass (PM2.5) and human mortality is well established, the most responsible particle types/sources are not yet certain. In May 2003, the U.S. Environmental Protection Agency's Particulate Matter Centers Prog...

  5. Source apportionment of the carcinogenic potential of polycyclic aromatic hydrocarbons (PAH) associated to airborne PM10 by a PMF model.

    PubMed

    Callén, M S; Iturmendi, A; López, J M; Mastral, A M

    2014-02-01

    In order to perform a study of the carcinogenic potential of polycyclic aromatic hydrocarbons (PAH), benzo(a)pyrene equivalent (BaP-eq) concentration was calculated and modelled by a receptor model based on positive matrix factorization (PMF). Nineteen PAH associated to airborne PM10 of Zaragoza, Spain, were quantified during the sampling period 2001-2009 and used as potential variables by the PMF model. Afterwards, multiple linear regression analysis was used to quantify the potential sources of BaP-eq. Five sources were obtained as the optimal solution and vehicular emission was identified as the main carcinogenic source (35 %) followed by heavy-duty vehicles (28 %), light-oil combustion (18 %), natural gas (10 %) and coal combustion (9 %). Two of the most prevailing directions contributing to this carcinogenic character were the NE and N directions associated with a highway, industrial parks and a paper factory. The lifetime lung cancer risk exceeded the unit risk of 8.7 x 10(-5) per ng/m(3) BaP in both winter and autumn seasons and the most contributing source was the vehicular emission factor becoming an important issue in control strategies.

  6. Source apportionment with uncertainty estimates of fine particulate matter in Ostrava, Czech Republic using Positive Matrix Factorization

    EPA Science Inventory

    A 14-week investigation during a warm and cold seasons was conducted to improve understanding of air pollution sources that might be impacting air quality in Ostrava, the Czech Republic. Fine particulate matter (PM2.5) samples were collected in consecutive 12-h day and night incr...

  7. Distribution, source apportionment, and transport of PAHs in sediments from the Pearl River Delta and the northern South China Sea

    SciTech Connect

    Luo, X.J.; Chen, S.J.; Mai, B.X.; Sheng, G.Y.; Fu, J.M.; Zeng, E.Y.

    2008-07-15

    Polycyclic aromatic hydrocarbons (PAHs) were measured in 59 surface sediments from rivers in the Pearl River Delta and the northern continental shelf of the South China Sea. Total PAH concentrations varied from 138 to 6,793 ng/g dry weight. The sources of PAH inputs to sediments in the Pearl River Delta were qualitatively and quantitatively determined by diagnostic ratios and principal components analysis with multiple linear regression. The results showed that on average coal and wood combustion, petroleum spills, vehicle emissions, and nature sources contributed 36%, 27%, 25%, and 12% of total PAHs, respectively. Coal and biomass combustion was the main source of PAHs in sediments of the South China Sea, whereas petroleum combustion was the main source of pyrolytic PAHs in riverine and estuarine sediments of the Pearl River Delta. Perylene was formed in situ in river sediments and then transported to coastal areas along with other PAHs. The relative abundance of perylene from five-ring PAHs can be used to estimate the contribution of riverine-discharged PAHs to coastal sediments.

  8. Source apportionment of fine and coarse particulate matter in a sub-urban area at the Western European Coast

    NASA Astrophysics Data System (ADS)

    Almeida, S. M.; Pio, C. A.; Freitas, M. C.; Reis, M. A.; Trancoso, M. A.

    Aerosol chemical composition data for PM 2.5 and PM 10-2.5, was acquired during the year 2001 at a sub-urban area located in the north outskirts of Lisbon. Principal component analysis (PCA) and multilinear regression analysis (MLRA) were used to identify possible sources of particulate matter (PM) and to determine their mass contribution. Seven main groups of sources were identified: soil, sea, secondary aerosols, road traffic, fuel-oil combustion, coal combustion and a Se/Hg emission source. In PM 2.5, secondary aerosol and vehicle exhaust contributed on average, with 25% and 22% to total mass, respectively, while sea spray and soil represented, respectively, 47% and 20% of the coarse fraction mass loading. Maritime air mass transport has a significant role on air quality in the North of Lisbon. Maritime transport scenarios are very frequent and promote the decrease of anthropogenic and mineral aerosol concentrations. The highest PM levels were recorded during South Continental episodes. These episodes are characterized by high mineral aerosol contents, due to the transport of dust from the interior of Iberian Peninsula and the Sahara desert. After identifying the contribution of PM sources, it is possible to conclude that abatement strategies to improve local air quality should focus on traffic and on non-mobile combustion processes emitting sulphur and NO x, which conduce to the formation of secondary aerosols.

  9. PM2.5 source apportionment in the southeastern U.S.: Spatial and seasonal variations during 2001-2005

    NASA Astrophysics Data System (ADS)

    Chen, Yingjun; Zheng, Mei; Edgerton, Eric S.; Ke, Lin; Sheng, Guoying; Fu, Jiamo

    2012-04-01

    The seasonal and spatial variations of source contributions of 112 composite fine particulate matter (PM2.5) samples collected in the Southeastern Aerosol Research and Characterization Study (SEARCH) monitoring network during 2001-2005 using molecular marker-based chemical mass balance (CMB-MM) model were determined. The lowest PM2.5 concentration occurs in January with higher values in warm months (maxima in July at four inland sites versus October at the coastal sites). Sulfate shows a similar pattern and plays a primary role in PM2.5 seasonality. Carbonaceous material (organic matter plus EC) exhibits less seasonality, but more spatial variations between the inland and coastal sites. Compared with the data at coastal sites, source attributions of diesel exhaust, gasoline exhaust, other organic matter (other OM), secondary sulfate, nitrate, and ammonium in PM2.5 mass at inland sites are higher. The difference in source attributions of wood combustion, meat cooking, vegetative detritus, and road dust among the eight sites is not significant. Contributions of eight primary sources to fine OC are wood burning (17 ± 19%), diesel exhaust (9 ± 4%), gasoline exhaust (5 ± 7%), meat cooking (5 ± 5%), road dust (2 ± 3%), vegetative detritus (2 ± 2%), cigarette smoke (2 ± 2% at four urban sites), and coke production (2 ± 1% only at BHM). Primary and secondary sources explain 82-100% of measured PM2.5 mass at the eight sites, including secondary ionic species (SO42-, NH4+, and NO3-; 41.4 ± 5.7%), identified OM (24.9 ± 11.3%), "other OM" (unexplained OM, 23.3 ± 10.3%), and "other mass" (11.4 ± 9.6%). Vehicle exhaust from both diesel and gasoline contributes the lowest fraction to PM2.5 mass in July and higher fractions at BHM and JST than other sites. Wood combustion, in contrast, contributes significantly to a larger fraction in winter than in summer. Road dust shows relatively high levels in July and April across the eight sites, while minor sources such as meat

  10. Source apportionment and health risk assessment of heavy metals in soil for a township in Jiangsu Province, China.

    PubMed

    Jiang, Yanxue; Chao, Sihong; Liu, Jianwei; Yang, Yue; Chen, Yanjiao; Zhang, Aichen; Cao, Hongbin

    2017-02-01

    Human activities contribute greatly to heavy metal pollution in soils. Concentrations of 15 metal elements were detected in 105 soil samples collected from a typical rural-industrial town in southern Jiangsu, China. Among them, 7 heavy metals-lead, copper, zinc, arsenic, chromium, cadmium, and nickel-were considered in the health risk assessment for residents via soil inhalation, dermal contact, and/or direct/indirect ingestion. Their potential sources were quantitatively apportioned by positive matrix factorization using the data set of all metal elements, in combination with geostatistical analysis, land use investigation, and industrial composition analysis. Furthermore, the health risks imposed by sources of heavy metal in soil were estimated for the first time. The results indicated that Cr, Cu, Cd, Pb, Ni, and Co accumulated in the soil, attaining a mild pollution level. The total hazard index values were 3.62 and 6.11, and the total cancer risks were 9.78 × 10(-4) and 4.03 × 10(-4) for adults and children, respectively. That is, both non-carcinogenic and carcinogenic risks posed by soil metals were above acceptable levels. Cr and As require special attention because the health risks of Cr and As individually exceeded the acceptable levels. The ingestion of homegrown produce was predominantly responsible for the high risks. The potential sources were apportioned as: a) waste incineration and textile/dyeing industries (28.3%), b) natural sources (45.4%), c) traffic emissions (5.3%), and d) electroplating industries and livestock/poultry breeding (21.0%). Health risks of four sources accounted for 23.5%, 32.7%, 7.4%, and 36.4% of the total risk, respectively.

  11. Fine particulate matter source apportionment for the Chemical speciation Trends Network site at Birmingham, Alabama, using Positive Matrix Factorization.

    PubMed

    Baumann, Karsten; Jayanty, R K M; Flanagan, James B

    2008-01-01

    The Positive Matrix Factorization (PMF) receptor model version 1.1 was used with data from the fine particulate matter (PM2.5) Chemical Speciation Trends Network (STN) to estimate source contributions to ambient PM2.5 in a highly industrialized urban setting in the southeastern United States. Model results consistently resolved 10 factors that are interpreted as two secondary, five industrial, one motor vehicle, one road dust, and one biomass burning sources. The STN dataset is generally not corrected for field blank levels, which are significant in the case of organic carbon (OC). Estimation of primary OC using the elemental carbon (EC) tracer method applied on a seasonal basis significantly improved the model's performance. Uniform increase of input data uncertainty and exclusion of a few outlier samples (associated with high potassium) further improved the model results. However, it was found that most PMF factors did not cleanly represent single source types and instead are "contaminated" by other sources, a situation that might be improved by controlling rotational ambiguity within the model. Secondary particulate matter formed by atmospheric processes, such as sulfate and secondary OC, contribute the majority of ambient PM2.5 and exhibit strong seasonality (37 +/- 10% winter vs. 55 +/- 16% summer average). Motor vehicle emissions constitute the biggest primary PM2.5 mass contribution with almost 25 +/- 2% long-term average and winter maximum of 29 +/- 11%. PM2.5 contributions from the five identified industrial sources vary little with season and average 14 +/- 1.3%. In summary, this study demonstrates the utility of the EC tracer method to effectively blank-correct the OC concentrations in the STN dataset. In addition, examination of the effect of input uncertainty estimates on model results indicates that the estimated uncertainties currently being provided with the STN data may be somewhat lower than the levels needed for optimum modeling results.

  12. Estimating population exposure to ambient polycyclic aromatic hydrocarbon in the United States - Part II: Source apportionment and cancer risk assessment.

    PubMed

    Zhang, Jie; Wang, Peng; Li, Jingyi; Mendola, Pauline; Sherman, Seth; Ying, Qi

    2016-12-01

    A revised Community Multiscale Air Quality (CMAQ) model was developed to simulate the emission, reactions, transport, deposition and gas-to-particle partitioning processes of 16 priority polycyclic aromatic hydrocarbons (PAHs), as described in Part I of the two-part series. The updated CMAQ model was applied in this study to quantify the contributions of different emission sources to the predicted PAH concentrations and excess cancer risk in the United States (US) in 2011. The cancer risk in the continental US due to inhalation exposure of outdoor naphthalene (NAPH) and seven larger carcinogenic PAHs (cPAHs) was predicted to be significant. The incremental lifetime cancer risk (ILCR) exceeds 1×10(-5) in many urban and industrial areas. Exposure to PAHs was estimated to result in 5704 (608-10,800) excess lifetime cancer cases. Point sources not related with energy generation and the oil and gas processes account for approximately 31% of the excess cancer cases, followed by non-road engines with 18.6% contributions. Contributions of residential wood combustion (16.2%) are similar to that of transportation-related sources (mostly motor vehicles with small contributions from railway and marine vessels; 13.4%). The oil and gas industry emissions, although large contributors to high concentrations of cPAHs regionally, are only responsible of 4.3% of the excess cancer cases, which is similar to the contributions of non-US sources (6.8%) and non-point sources (7.2%). The power generation units pose the most minimal impact on excess cancer risk, with contributions of approximately 2.3%.

  13. Spatial distributions, source apportionment and ecological risk of SVOCs in water and sediment from Xijiang River, Pearl River Delta.

    PubMed

    Tang, Jiao; An, Taicheng; Li, Guiying; Wei, Chaohai

    2017-03-09

    Xijiang River is an important drinking water source in Guangxi Province, China. Along the Xijiang River and surrounding tributary, the pollution profile of three important groups of semi-volatile organic compounds, including polycyclic aromatic hydrocarbons (PAHs), organochlorine pesticides (OCPs) and phthalate esters (PAEs), was analyzed. Relatively low levels of PAHs (64-3.7 × 10(2) ng L(-1)) and OCPs (16-70 ng L(-1)), but high levels of PAEs (7.9 × 10(2)-6.8 × 10(3) ng L(-1)) occurred in the water. Comparatively, low levels of OCPs (39-1.8 × 10(2) ng g(-1)) and PAEs (21-81 ng g(-1)), but high levels of PAHs (41-1.1 × 10(3) ng g(-1)) were found in sediment. Principal component analyses for source identification indicated petroleum-derived residues or coal and biomass combustion, and vehicular emission was the main sources for PAHs. The OCPs sources of each category were almost independent, whereas the new input of HCHs and p,p'-DDTs probably existed in some areas. PAEs were mainly originated from personal care products of urban sewage, plastic and other industrial sources. Ecological risk through the risk quotient analysis indicated a small or significant potential adverse effect on fish, daphnia and green algae. Nevertheless, the integrated risk of all pollutants should be taken into account in future study.

  14. Atmospheric Deposition of Metals and Organics onto Massachusetts and Cape COD Bays: a Comparison of Measurement Techniques and Source Apportionment

    NASA Astrophysics Data System (ADS)

    Underhill, Jeffrey T.

    Toxic materials enter Massachusetts and Cape Cod Bays in many different ways. While most pollutants enter the Bay area by means of direct source outfalls, river outflow and storm water runoff, a significant amount of certain materials come from the atmosphere. Pollutants in the atmosphere, both gaseous and particles eventually settle to the ground or are washed out of the air by precipitation. In many locations atmospheric deposition provides a significant contribution to surface water contamination. The deposition of atmospheric pollutants onto Massachusetts Bay and Cape Cod Bay was measured using wet/dry collection buckets at two locations along the shores of the Bay area: Nahant, 16 km northeast of Boston, and Truro, Cape Cod, 100 km southeast of Boston. A dichotomous sampler was also used at Nahant to collect atmospheric aerosols. Collected samples were analyzed by Inductively Coupled Plasma Mass Spectrometry (ICP-MS) and Instrumental Neutron Activation Analysis (INAA) for select toxic metals. Analysis of polycyclic aromatic hydrocarbons (PAHs) was performed by Gas Chromatography Mass Spectrometry (GC-MS). Dry deposition of most toxic metals were found to be higher at Nahant compared to Truro. Conversely, wet deposition rates were generally higher at Truro most likely due to transport from regional sources. Altogether, regional sources are believed to be the primary contributors of metals to the Bays. PAH deposition rates were higher at Nahant. Local sources are believed to be the primary contributors of PAH deposition. Metals and their compounds appear to have a longer residence time in the atmosphere than the organic PAH. Estimated deposition to Massachusetts and Cape Cod Bays compares favorably to the results presented in a 1991 study by Menzie-Cura Associates. Current estimates of total deposition of cadmium, cobalt, copper, nickel and lead to the surface waters of the Bay region are lower than the Menzie-Cura study. Chromium, antimony, manganese, selenium

  15. Source apportionment of PM₁₀ and PM₂.₅ in a desert region in northern Chile.

    PubMed

    Jorquera, Héctor; Barraza, Francisco

    2013-02-01

    Estimating contributions of anthropogenic sources to ambient particulate matter (PM) in desert regions is a challenging issue because wind erosion contributions are ubiquitous, significant and difficult to quantify by using source-oriented, dispersion models. A receptor modeling analysis has been applied to ambient PM(10) and PM(2.5) measured in an industrial zone ~20 km SE of Antofagasta (23.63°S, 70.39°W), a midsize coastal city in northern Chile; the monitoring site is within a desert region that extends from northern Chile to southern Perú. Integrated 24-hour ambient samples of PM(10) and PM(2.5) were taken with Harvard Impactors; samples were analyzed by X Ray Fluorescence, ionic chromatography (NO(3)(-) and SO(4)(=)), atomic absorption (Na(+), K(+)) and thermal optical transmission for elemental and organic carbon determination. Receptor modeling was carried out using Positive Matrix Factorization (US EPA Version 3.0); sources were identified by looking at specific tracers, tracer ratios, local winds and wind trajectories computed from NOAA's HYSPLIT model. For the PM(2.5) fraction, six contributions were found - cement plant, 33.7 ± 1.3%; soil dust, 22.4 ± 1.6%; sulfates, 17.8 ± 1.7%; mineral stockpiles and brine plant, 12.4 ± 1.2%; Antofagasta, 8.5 ± 1.3% and copper smelter, 5.3 ± 0.8%. For the PM(10) fraction five sources were identified - cement plant, 38.2 ± 1.5%; soil dust, 31.2 ± 2.3%; mineral stockpiles and brine plant, 12.7 ± 1.7%; copper smelter, 11.5 ± 1.6% and marine aerosol, 6.5 ± 2.4%. Therefore local sources contribute to ambient PM concentrations more than distant sources (Antofagasta, marine aerosol) do. Soil dust is enriched with deposition of marine aerosol and calcium, sulfates and heavy metals from surrounding industrial activities. The mean contribution of suspended soil dust to PM(10) is 50 μg/m(3) and the peak daily value is 104 μg/m(3). For the PM(2.5) fraction, suspended soil dust contributes with an average of 9.3

  16. Source apportionment of atmospheric ammonia before, during, and after the 2014 APEC summit in Beijing using stable nitrogen isotope signatures

    NASA Astrophysics Data System (ADS)

    Chang, Yunhua; Liu, Xuejun; Deng, Congrui; Dore, Anthony J.; Zhuang, Guoshun

    2016-09-01

    Stable nitrogen isotope composition (δ15N) offers new opportunities to address the long-standing and ongoing controversy regarding the origins of ambient ammonia (NH3), a vital precursor of PM2.5 (particulate matters with aerodynamic diameter equal or less than 2.5 µm) inorganic components, in the urban atmosphere. In this study, the δ15N values of NH3 samples collected from various sources were constrained using a novel and robust chemical method coupled with standard elemental analysis procedures. Independent of the wide variation in mass concentrations (ranging from 33 (vehicle) to over 6000 (human excreta) µg m-3), different NH3 sources have generally different δ15N values (ranging from -52.0 to -9.6 ‰). Significantly high δ15N values are seen as a characteristic feature of all vehicle-derived NH3 samples (-14.2 ± 2.8 ‰), which can be distinguished from other sources emitted at environmental temperature (-29.1 ± 1.7, -37.8 ± 3.6, and -50.0 ± 1.8 ‰ for livestock, waste, and fertilizer, respectively). The isotope δ15N signatures for a range of NH3 emission sources were used to evaluate the contributions of the different sources within measured ambient NH3 in Beijing, using an isotope mixing model (IsoSource). The method was used to quantify the sources of ambient NH3 before, during and after the 2014 Asia-Pacific Economic Cooperation (APEC) summit, when a set of stringent air quality control measures were implemented. Results show that the average NH3 concentrations (the overall contributions of traffic, waste, livestock, and fertilizer) during the three periods were 9.1 (20.3, 28.3, 23.6, and 27.7 %), 7.3 (8.8, 24.9, 14.3, and 52.0 %), and 12.7 (29.4, 23.6, 31.7, and 15.4 %) µg m-3, respectively, representing a 20.0 % decrease first and then a 74.5 % increase in overall NH3 mass concentrations. During (after) the summit, the contributions of traffic, waste, livestock, and fertilizer decreased (increased) by 56.7 (234.2), 12.0 (-5.0), 39.4 (120

  17. Source apportionment of sulfate and nitrate particulate matter in the Eastern United States and effectiveness of emission control programs.

    PubMed

    Zhang, Hongliang; Hu, Jianlin; Kleeman, Michael; Ying, Qi

    2014-08-15

    Reducing population exposure to PM2.5 in the eastern US will require control of secondary sulfate and nitrate. A source-oriented Community Multi-scale Air Quality (CMAQ) model is used to determine contributions of major emission sources to nitrate and sulfate concentrations in the seven eastern US cities (New York City, Pittsburgh, Baltimore, Chicago, Detroit, St. Paul, and Winston-Salem) in January and August of 2000 and 2006. Identified major nitrate sources include on-road gasoline-powered vehicles, diesel engines, natural gas and coal combustion. From 2000 to 2006, January nitrate concentrations decreased by 25-68% for all the seven cities. On average, ~53% of this change was caused by emissions controls while 47% was caused by meteorology variations. August nitrate concentrations decreased by a maximum of 68% in New York City but Detroit experienced increasing August nitrate concentrations by up to 33%. On average, ~33% of the reduction in nitrate is offset by increases associated with meteorological conditions that favor nitrate formation. Coal combustion and natural gas are the dominant sources for sulfate in both seasons. January sulfate decrease from 2000 to 2006 in all cities by 4-58% except New York City, which increases by 13%. On average, ~93% of the reduction in sulfate was attributed to emission controls with 7% associated with changes in meteorology. August sulfate concentrations decrease by 11-44% in all cities. On average, emission controls alone between 2000 and 2006 would have caused 6% more reduction but the effectiveness of the controls was mitigated by meteorology conditions more favorable to sulfate production in 2006 vs. 2000. The results of this study suggest that regional emissions controls between 2000 and 2006 have been effective at reducing population exposure to PM2.5 in the eastern US, but yearly variations in meteorology must be carefully considered when assessing the exact magnitude of the control benefits.

  18. Source apportionment of wide range particle size spectra and black carbon collected at the airport of Venice (Italy)

    NASA Astrophysics Data System (ADS)

    Masiol, Mauro; Vu, Tuan V.; Beddows, David C. S.; Harrison, Roy M.

    2016-08-01

    Atmospheric particles are of high concern due to their toxic properties and effects on climate, and large airports are known as significant sources of particles. This study investigates the contribution of the Airport of Venice (Italy) to black carbon (BC), total particle number concentrations (PNC) and particle number size distributions (PNSD) over a large range (14 nm-20 μm). Continuous measurements were conducted between April and June 2014 at a site located 110 m from the main taxiway and 300 m from the runway. Results revealed no significantly elevated levels of BC and PNC, but exhibited characteristic diurnal profiles. PNSD were then analysed using both k-means cluster analysis and positive matrix factorization. Five clusters were extracted and identified as midday nucleation events, road traffic, aircraft, airport and nighttime pollution. Six factors were apportioned and identified as probable sources according to the size profiles, directional association, diurnal variation, road and airport traffic volumes and their relationships to micrometeorology and common air pollutants. Photochemical nucleation accounted for ∼44% of total number, followed by road + shipping traffic (26%). Airport-related emissions accounted for ∼20% of total PNC and showed a main mode at 80 nm and a second mode beyond the lower limit of the SMPS (<14 nm). The remaining factors accounted for less than 10% of number counts, but were relevant for total volume concentrations: nighttime nitrate, regional pollution and local resuspension. An analysis of BC levels over different wind sectors revealed no especially significant contributions from specific directions associated with the main local sources, but a potentially significant role of diurnal dynamics of the mixing layer on BC levels. The approaches adopted in this study have identified and apportioned the main sources of particles and BC at an international airport located in area affected by a complex emission scenario. The

  19. Measurement and apportionment of radon source terms for modeling indoor environments. Annual progress report, March 1991--February 1992

    SciTech Connect

    Harley, N.H.

    1992-02-01

    This research has two main goals; (1) to quantify mechanisms for radon entry into homes of different types and to determine the fraction of indoor radon attributable to each source and (2) to model and calculate the dose (and therefore alpha particle fluence) to cells in the human and animal tracheobronchial tree that is pertinent to induction of bronchogenic carcinoma from inhaled radon daughters. The dosimetry has been extended to include organs other than the lung.

  20. Probabilistic ecological risk assessment and source apportionment of polycyclic aromatic hydrocarbons in surface sediments from Yellow Sea.

    PubMed

    Liu, Ai-Xia; Lang, Yin-Hai; Xue, Li-Dong; Liao, Shu-Lin; Zhou, Hong

    2009-11-01

    Based on the concentrations of polycyclic aromatic hydrocarbons (PAHs) in 12 surface sediment samples from Yellow sea, the relative risk of 9 PAHs was investigated using joint risk probability distribution curves and overlapping area, which were generated based on the distributions of exposure and acute toxicity data (LC(50)), and the sources of PAHs were apportioned using principal component analysis. It was found that joint probability curve and overlapping area indicated the acceptable ecological risk of individual PAHs, only a small fraction of the benthic organisms was affected. Among the nine PAHs studied, the overall risk of pyrene was the highest, with that of naphthalene the lowest. For lower exposure levels at which the percentage of species affected was less than 10%, the risk associated with phenanthrene and fluorene were clearly higher than that of the other seven PAHs. It was indicated that PAHs in surface sediments mainly originated from vehicular emissions, coal combustion sources, coke oven emission and wood combustion, petroleum origin made little influence on sources of PAHs by PCA.