Science.gov

Sample records for 18ni maraging steel

  1. Stress corrosion cracking susceptibility of 18 Ni maraging steel

    NASA Technical Reports Server (NTRS)

    Humphries, T. S.; Nelson, E. E.

    1974-01-01

    The stress corrosion cracking (SCC) resistance of 18Ni maraging steel (grades 200, 250, 300, and 350) was determined in 3.5 percent salt (NaCl) solution, synthetic sea water, high humidity, and outside MSFC atmosphere. All grades of the maraging steel were found to be susceptible to SCC in varying degrees according to their strengths, with the lowest strength steel (grade 200) being the least susceptible and the highest strength steel (grade 350), the most susceptible to SCC. The SCC resistance of 250 grade maraging steel was also evaluated in salt and salt-chromate solutions using fracture mechanics techniques. The threshold value, K sub SCC, was found to be approximately 44 MN/sq m square root m, (40 ksi square root in.) or 40 percent of the K sub Q value.

  2. Hydrogen enhanced crack growth in 18 Ni maraging steels

    NASA Technical Reports Server (NTRS)

    Hudak, S. J., Jr.; Wei, R. P.

    1976-01-01

    The kinetics of sustained-load subcritical crack growth for 18 Ni maraging steels in high-purity hydrogen are examined using the crack-tip stress intensity factor K as a measure of crack driving force. Crack growth rate as a function of stress intensity exhibited a clearly defined K-independent stage (Stage II). Crack growth rates in an 18 Ni (grade 250) maraging steel are examined for temperatures from -6 to +100 C. A critical temperature was observed above which crack growth rates became diminishingly small. At lower temperatures the activation energy for Stage II crack growth was found to be 16.7 plus or minus 3.3 kJ/mole. Temperature and hydrogen partial pressure are shown to interact in a complex manner to determine the apparent Kth (stress intensity level below which no observable crack growth occurs) and the crack growth behavior. Comparison of results on '250' and '300' grades of 18 Ni maraging steel indicate a significant influence of alloy composition and/or strength level on the crack growth behavior.

  3. Reclamation and additional alloying of 18Ni(350) maraging steel

    SciTech Connect

    Ahmed, M.; Salam, I.; Nasim, I.; Hussain, S.W.; Hashmi, F.H.; Khan, A.Q. )

    1994-06-01

    The possibility of gainfully utilizing grade 18Ni(350) maraging steel scrap has been investigated, along with the effect of additional alloying with niobium. A vacuum induction melting and casting furnace was used for melting and additional alloying. The cast ingots were hot forged and their properties compared with those of the stock material. The composition of the reprocessed material was found to be within the prescribed range for 18Ni(350) steel, except for some loss in titanium content. The hardness and tensile strength of the recycled steels were similar to those of the stock material. A slight decrease in hardness in the aged condition could be attributed to loss of titanium during remelting. Charpy V-notch impact testing indicated significantly higher toughness in the remelted material; this has been attributed to a homogeneous, refined microstructure and a lower level of inclusions. Additional alloying with 2% Nb not only improved the mechanical properties but also affected the amount of reverted austenite obtained after aging.

  4. The rolling texture of 18% Ni-350 maraging steel

    SciTech Connect

    Haq, A. ul; Khan, A.Q. )

    1993-02-01

    Texture development in hot rolled sheet and hot forged tube of 18% Ni-350 maraging steel has been studied after various degrees of cold deformation and flow turning, respectively. Hot rolled sheet exhibited considerable mechanical anisotropy. Weak texture development was observed following flow turning compared to cold deformation. Above 80% deformation, an increase in work hardening was accompanied by an increase in the orientation density of the texture component (001)[110]. Deformation of 97% leads to the development of the texture component (111)[110], with the highest orientation density 10.3 times random and a constant orientation density of 9 times random along [var phi][sub 1] at [phi] = 55[degree] and [var phi][sub 2] = 45[degree]. This texture was correlated with the appearance of shear bands in the microstructure.

  5. Mechanical behavior of 18 Ni 200 grade maraging steel at cryogenic temperatures

    NASA Technical Reports Server (NTRS)

    Wagner, J. A.

    1985-01-01

    A comprehensive study was conducted to characterize the mechanical behavior of 18 Ni 200 grade maraging steel for cryogenic applications in the National Transonic Facility. Tensile, fatigue, impact, and fracture toughness properties were determined at room and cryogenic temperatures. Experimental variables included product form, specimen orientation, and variation in metallurgical condition accomplished with a grain refining heat treatment. Room temperature tensile yield strength was approximately 200 ksi, while the yield strength at -275 F was approximately 260 ksi. Charpy V-notch energy absorption values and fracture toughness values of 18 Ni steel were found to be dependent on temperature, product form, orientation, and metallurgical condition. Fracture toughness values ranged from 80 to 113 ksi-sq rt in. at room temperature and from 67 to 90 ksi-sq rt in. at -275 F. The results of this study indicate that 18 Ni 200 grade maraging steel exceeds the strength criterion of 150 ksi minimum yield strength for use in cryogenic wind tunnel models but is marginal with respect to the 85 ksi sq rt in fracture toughness criterion at -275 F.

  6. Fractographic analysis of gaseous hydrogen induced cracking in 18Ni maraging steel

    NASA Technical Reports Server (NTRS)

    Gangloff, R. P.; Wei, R. P.

    1978-01-01

    Electron microscope fractographic analysis supplemented an extensive study of the kinetics of gaseous hydrogen assisted cracking in 18Ni maraging steel. Temperature determined the crack path morphology in each steel which, in turn, was directly related to the temperature dependence of the crack growth rate. Crack growth in the low temperature regime proceeded along prior austenite grain boundaries. Increasing the temperature above a critical value produced a continuously increasing proportion of transgranular quasi-cleavage associated with lath martensite boundaries. The amount of transgranular cracking was qualitatively correlated with the degree of temperature-induced deviation from Arrhenius behavior. Fractographic observations are interpreted in terms of hypothesized mechanisms for gaseous hydrogen embrittlement. It is concluded that hydrogen segregation to prior austenite and lath martensite boundaries must be considered as a significant factor in developing mechanisms for gaseous embrittlement of high strength steels.

  7. The effect of microstructure and strength on the fracture toughness of an 18 Ni, 300 grade maraging steel

    NASA Technical Reports Server (NTRS)

    Psioda, J. A.; Low, J. R., Jr.

    1975-01-01

    A 300 grade maraging steel was chosen as a vehicle by which to understand the inverse relationship between strength and toughness in high strength alloys such as the 18 Ni maraging steels. The 18 Ni, 300 grade maraging material was a commercial grade consumable-electrode, vacuum arc remelted heat obtained in the form of forged and annealed plate. The matrix contained a population of second-phase impurity inclusions which was a product of the casting and hot working processes. These inclusions did not change with subsequent precipitation hardening. Changes in microstructure resulting in strength increases were brought about by variations in aging temperature and time. Maximum strength was attained in the 300 grade maraging steel by aging at 427 C (800 F) for 100 hours. Tensile, fatigue precracked Charpy impact, and plane-strain fracture toughness tests were performed at room temperature, 20 C (68 F). With increasing strength the fracture toughness decreases as smaller and smaller inclusions act as sites for void initiation.

  8. Acoustic emission response of 18% Ni maraging steel weldment with inserted cracks of varying depth to thickness ratio

    SciTech Connect

    Chelladurai, T.; Sankaranarayanan, A.S.; Acharya, A.R.; Krishnamurthy, R.

    1995-06-01

    Acoustic emission studies have been carried out on a batch of welded and center cracked specimens made of 18% Ni M250 maraging steel where the crack depth to specimen thickness ratio varied from approximately 10/80 to 25/80. Broad band AE transducers providing maximum sensitivity in frequency range 135 to 310 KHz were used for the AE monitoring. The paper brings out the AE performance of the specimens with inserted surface cracks of different sizes when the latter become critically severe leading to failure. The studies indicate the prediction possibility for the hardware constructed out of this material reasonably well before their final rupture. The AE signatures are also presented in a form that would facilitate generation of an acceptance criteria for the evaluation of hardware in real time.

  9. The effect of microstructure and strength on the fracture toughness of an 18 ni, 300 grade maraging steel

    NASA Technical Reports Server (NTRS)

    Psioda, J. A.; Low, J. R., Jr.

    1974-01-01

    Methods for increasing the strength of maraging steels are discussed. An investigation was conducted to systematically vary the strength of 18 weight percent nickel, 300 grade maraging steel, to isolate any attending microstructural changes, and to study the effects of these changes on the fracture toughness of the alloy. A study aimed at determining the aging behavior of the program alloy was carried out to provide data by which to estimate yield strength. The effects of various alloying materials on the strength of the maraging steel are examined. The mechanical properties of the 300 grade maraging steel were determined by tension tests, fatigue precracked Charpy impact tests, and plane strain fracture toughness tests.

  10. Influence of repair welding of aged 18Ni 250 maraging steel weldments on tensile and fracture properties

    SciTech Connect

    Sinha, P.P.; Arumugham, S.; Nagarajan, K.V. . Materials and Metallurgy Group)

    1993-08-01

    The effects of repair welding on tensile strength and fracture toughness of aged weldments of 18 Ni 250-grade maraging steel have been studied. It has been established that aged weldments in the steel can be repaired and approximately 95% of the tensile strength of the initial welds could be achieved by postrepair aging treatment. Also, the repairs had practically no effect on the fracture toughness (K[sub IC]) of the weldment. These results have been discussed in terms of microstructural conditions in the various affected and unaffected zones of the initial weld. One important inference that emerges from the mechanical properties-microstructural correlation in the study is that (K[sub IC]) of the weld is independent of the gross microstructural features of the dendritic size and shapes in the ranges observed in this study. It has, however, been cautioned that the above statement is not valid in cases in which heavy segregation occurs along the interdendritic boundaries resulting in heavily banded microstructure. This can result from faulty weld parameters such as excessive heat input. A second aging to recover the mechanical properties of the repaired zone has additional beneficial effects on tensile strengths and helps in maintaining fracture toughness to the original level of the initial weld.

  11. Plasticity and ab initio characterizations on Fe 4N produced on the surface of nanocrystallized 18Ni-maraging steel plasma nitrided at lower temperature

    NASA Astrophysics Data System (ADS)

    Yan, M. F.; Wu, Y. Q.; Liu, R. L.

    2009-08-01

    18Ni-maraging steel has been entirely nanocrystallized by a series of processes including solution treatment, hot-rolling deformation, cold-drawn deformation and direct electric heating. The plasma nitriding of nanocrystallized 18Ni-maraging steel was carried out at 410 °C for 3 h and 6 h in a mixture gas of 20% N 2 + 80% H 2 with a pressure of 400 Pa. The surface phase constructions and nitrogen concentration profile in surface layer were analyzed using an X-ray diffractometer (XRD) and the glow discharge spectrometry (GDS), respectively. The results show that an about 2 μm thick compound layer (mono-phase γ'-Fe 4N) can be produced on the top of the surface layer of nanocrystallized 18Ni-maraging steel plasma nitrided at 410 °C for 6 h. The measured hardness value of the nitrided surface is 11.6 GPa. More importantly, the γ'-Fe 4N phase has better plasticity, i.e., its plastic deformation energy calculated from the load-displacement curve obtained by nano-indentation tester is close to that of nanocrystallized 18Ni-maraging steel. Additionally, the mechanical properties of γ'-Fe 4N phase were also characterized by first-principles calculations. The calculated results indicate that the hardness value and the ratio of bulk to shear modulus ( B/ G) of the γ'-Fe 4N phase are 10.15 GPa and 3.12 (>1.75), respectively. This demonstrates that the γ'-Fe 4N phase has higher hardness and better ductility.

  12. Grain and grain boundary characters in surface layer of untreated and plasma nitrocarburized 18Ni maraging steel with nanocrystalline structure

    NASA Astrophysics Data System (ADS)

    Yan, M. F.; Wu, Y. Q.; Liu, R. L.

    2013-05-01

    The nanocrystallized 18Ni maraging steel was plasma nitrocarburized at 460 °C for 4 h in a mixture gas of N2, H2 and C2H5OH. The surface phase compositions of the specimens were analyzed using X-ray diffractometer. The grain shape and size, and grain boundaries in the subsurface layers of the samples were characterized by electron backscattering diffraction and transmission electron microscopy. The results show that the nitrocarburized layers are composed of α-Fe, γ‧-Fe4N and FeN0.049 phases. Most α-Fe and γ‧-Fe4N grains show in columnar shape. The major and minor axes of some α-Fe grains are elongated and shortened after nitrocarburizing, respectively. In the subsurface layers of the untreated and nitrocarburized specimens, the average areas of γ‧-Fe4N and α-Fe grains both with a dimension of nanometer are 0.395 μm2 and 0.397 μm2, respectively. The γ‧-Fe4N grain boundaries are mainly high angle boundaries with a very small fraction of low angle boundaries. Coincidence site lattice boundaries in the subsurface layer of the untreated specimen are composed mainly of Σ3, Σ11 and Σ13b, and their fraction decreases after nitrocarburizing.

  13. The effect of microstructure and strength on the fracture toughness of an 18 Ni, 300 grade maraging steel

    NASA Technical Reports Server (NTRS)

    Psioda, J. A.; Low, J. R., Jr.

    1977-01-01

    Fractography and metallographic sectioning were used to investigate the influence of microstructure and strength on the fracture toughness (KIc) and fracture mechanism of an 18 Ni, 300 grade maraging steel. Increased yield strength from 1442 to 2070 MN/m squared through precipitation hardening results in a KIc loss from 143 to 55 MN/m superscript 3/2. Ti (C,N) Ti2S, and TiC inclusions in sizes from 1 to 8, 1 to 15, and 0.1 to 2 microns respectively serve as sites for void nucleation and lead to fracture by the dimpled rupture process in all strength levels considered. TiC nucleated dimples occupy more than half the fracture in all conditions. Void nucleation rate and resultant number of dimples per unit area of fracture increase with increasing yield strength. Average dimple size decreases with increasing strength and/or overaging which follows from the decreasing amount of stable void growth measured by sectioning tensile specimens. Void growth is assisted by crack branching along a path of TiC inclusions. Coalescence occurs in the highest strength materials by a combination of TiC void nucleation and premature separation at strengthening precipitates.

  14. Correlation of mechanical properties with metallurgical structure for 18Ni 200 grade maraging steel at room and cryogenic temperatures

    NASA Technical Reports Server (NTRS)

    Wagner, J. A.

    1991-01-01

    An extensive metallurgical study is presented which is intended to explain variations in the mechanical properties of Ni18 200 grade maraging steel in various product forms and orientations. Fracture toughness and Charpy impact values are found to decrease with decreasing temperature and be dependent on product form, specimen orientation, and metallurgical condition. Fatigue crack growth rates are dependent on temperature only. Fractographic analysis reveals that the decrease in toughness at -170 C is not associated with cleavage-type fracture morphology. Those specimens exhibiting low fracture toughness at room temperature or -170 C are found to have a significantly larger number of titanium-rich particles associated with dimple formation on the fracture surface.

  15. Maraging Steel Machining Improvements

    DTIC Science & Technology

    2007-04-23

    APR 2007 2. REPORT TYPE Technical, Success Story 3. DATES COVERED 01-12-2006 to 23-04-2007 4. TITLE AND SUBTITLE Maraging Steel Machining...consumers of cobalt-strengthened maraging steel . An increase in production requires them to reduce the machining time of certain operations producing... maraging steel ; Success Stories 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT 1 18. NUMBER OF PAGES 1 19a. NAME OF RESPONSIBLE

  16. Cobalt free maraging steel

    SciTech Connect

    Floreen, S.

    1984-04-17

    The subject invention is directed to ferrous-base alloys, particularly to a cobalt-free maraging steel of novel chemistry characterized by a desired combination of strength and toughness, notwithstanding that cobalt is non-essential.

  17. Metallography of maraging 350 steel

    SciTech Connect

    Hutson, S.M.; Merten, C.W.

    1987-01-01

    A technique for etching maraging 350 steel with Glyceregia is described. Surface activation procedures are integral to this technique. Microstructural features revealed by this technique are compared with those obtained with Kalling's reagent, Fry's reagent, and 5% Nital, three etchants commonly used to reveal microstructures of maraging steels. Features which may be simultaneously revealed using Glyceregia include prior austenite grain boundaries, martensitic structure, precipitates, titanium carbo-nitrides, and reverted austenite. The other etchants examined in this investigation typically reveal only a few of the microstructural features detailed above at any one time. 11 refs., 10 figs., 2 tabs.

  18. An internal friction peak caused by hydrogen in maraging steel

    SciTech Connect

    Usui, Makoto; Asano, Shigeru

    1996-01-01

    Internal friction in hydrogen-charged iron and steel has so far been studied by a large number of investigators. For pure iron, a well-defined peak of internal friction has been observed under the cold-worked and hydrogen-charged conditions. This is called the hydrogen cold-work peak, or the Snoek-Koester relaxation, which originates from the hydrogen-dislocation interaction. In the present study, a high-strength maraging steel (Fe-18Ni-9Co-5Mo) was chosen as another high-alloy steel which is known to be very susceptible to hydrogen embrittlement. The purpose of this paper is to show a new internal friction peak caused by hydrogen in the maraging steel and to compare it with those found in stainless steels which have so far been studied as typical engineering high-alloy materials.

  19. Magnetic properties of maraging steels in relation to nickel concentration

    SciTech Connect

    Ahmed, M.; Nasim, I.; Ayub, H.; Hasnain, K.

    1995-07-01

    Magnetic properties of maraging steels have been investigated as a function of nickel concentration. The alloys nickel content varied from 12 to 24 wt pct, while other alloying constituents were kept at a level maintained in the 18Ni-2,400 MPA-grade maraging steel. The magnetic properties were determined following aging for 1 hour in the temperature range of 450 to 750 C. In every alloy investigated, the coercive field increased with aging temperature, reaching a maximum around 670 C {+-} 30 C. The saturation magnetization values were lowest around temperatures where maximum coercive field was observed. The coercive field increased from {approximately}55 to {approximately}175 Oe ({approximately}4,380 to {approximately} 13,900 amp/meter) and the corresponding saturation magnetization decreased from {approximately}18,500 to {approximately}4,000 G ({approximately}1.85 to {approximately}0.4 T) in the alloys containing 12 and 24 wt pct Ni, respectively. The reverted austenite increased from 25 vol pct at 12 wt pct Ni to 10 vol pct at 24 wt pct Ni. The hardness and Charpy impact strength of the alloys have also been determined. An attempt has been made to correlate magnetic properties with different phase transformations occurring in maraging steels.

  20. Banding of MAR-aging steel

    SciTech Connect

    Hays, C.; Stemmler, R.P.

    2000-04-01

    MAR-aging steels have gained a respectable position among design engineers who demand ultra-high strength, reasonable ductility, and good fracture toughness, especially where outerspace and aerospace applications are concerned. This specialty steel category of MAR-aging alloys owes its unique properties to a complex hardening reaction, which involves precipitation of uniform intragranular ribbons (Ni{sub 3}Mo phase) on dislocations during the treatment cycle. Like any other metallurgical process, MAR-aging treatment cycles can become quite difficult, if not impossible. When that condition does exist, the end result is often called a dead heat by MAR-aging technologists. This paper examines a dead heat and makes appropriate comparisons to other live heats. Salient differences and interactive similarities are both studied in terms of microstructure, serial sections, chemical composition, and selected mechanical properties. The intent of this paper is to shed more light on the previously indistinct subject of banding.

  1. Microstructure and mechanical properties of Selective Laser Melted 18Ni-300 steel

    NASA Astrophysics Data System (ADS)

    Kempen, K.; Yasa, E.; Thijs, L.; Kruth, J.-P.; Van Humbeeck, J.

    Selective Laser Melting (SLM) is an Additive Manufacturing process in which a part is built in a layer by layer manner. A laser source selectively scans the powder bed according to the CAD data of the part to be produced. The high intensity laser beam makes it possible to completely melt the metal powder particles to obtain almost fully dense parts. In this work, the influence of process parameters in SLM (e.g. scan speed and layer thickness) and various age hardening treatments on the microstructure and mechanical properties of 18Ni-300 steel is investigated. It is shown that almost fully dense parts with mechanical properties comparable to those of conventionally produced maraging steel 300 can be produced by SLM.

  2. Laser shock-induced mechanical and microstructural modification of welded maraging steel

    SciTech Connect

    Banas, G. ); Elsayed-Ali, H.E. ); Lawrence, F.V. Jr. ); Rigsbee, J.M. )

    1990-03-01

    The effect of laser-induced high-intensity stress waves on the hardness, fatigue resistance, and microstructure in the heat affected zone of welded 18 Ni(250) maraging steel was investigated. Laser-shock processing increased the hardness and fatigue strength of the weldments. Some melting of the surface was involved during laser-shock hardening which produced the reverted austenite phase. Microscopic analyses showed an increased dislocation density in the laser-shocked area.

  3. Dendritic inhomogeneity of stainless maraging steels

    SciTech Connect

    Krasnikova, S.I.; Drobot, A.V.; Shmelev, A.Y.; Vukelich, S.B.

    1986-03-01

    The authors investigated dendritic inhomogeneity in industrial ingots 630 mm (steel I) in diameter and 500 mm (steel II) in diameter. The variation in the degree of dendritic inhomogeneity was investigated over the height of the ingots and across the sections on an MS-46 microprobe. It was established that the elements can be placed in the following order in accordance with the degree of reduction in the liquation factor: titanium, molybdenum, nickel, chromium, and cobalt. Titanium and molybdenum exhibit forward liquation in both steels, and chromium in steel II. The distribution of nickel and chromium in the steel I ingots and cobalt in the steel II ingots is unconventional. Dendritic inhomogeneity, which must be considered in assigning the heat treatment for finished articles, develops during the crystallization of stainless maraging steels.

  4. An investigation of the plastic fracture of AISI 4340 and 18 nickel - 200 grade maraging steels

    NASA Technical Reports Server (NTRS)

    Cox, T. B.; Low, J. R., Jr.

    1974-01-01

    The mechanisms of plastic fracture (dimpled rupture) in high-purity and commercial 18 Ni, 200 grade maraging steels and quenched and tempered AISI 4340 steels have been studied. Plastic fracture takes place in the maraging alloys through void initiation by fracture of titanium carbo-nitride inclusions and the growth of these voids until impingement results in coalescence and final fracture. The fracture of AISI 4340 steel at a yield strength of 200 ksi occurs by nucleation and subsequent growth of voids formed by fracture of the interface between manganese sulfide inclusions and the matrix. The growth of these inclusion-nucleated voids is interrupted long before coalescence by impingement, by the formation of void sheets which connect neighboring sulfide-nucleated voids.

  5. Precipitation hardening in 350 grade maraging steel

    SciTech Connect

    Viswanathan, U.K. . Radiometallurgy Div.); Dey, G.K. . Metallurgy Division); Asundi, M.K. )

    1993-11-01

    Evolution of microstructure in 350 grade commercial maraging steel has been examined. In the earlier stages of aging, the strengthening phases are formed by the heterogeneous precipitation, and these phases have been identified as intermetallic compounds of the Ni[sub 3] (Ti, Mo) and Fe[sub 2]Mo types. The kinetics of precipitation are studied in terms of the activation energy by carrying out isothermal hardness measurements of aged material. The mechanical properties in the peak-aged and overaged conditions were evaluated and the flow behavior examined. The overaging behavior of the steel has been studied and the formation of austenite of different morphologies identified. The crystallography of the austenite has been examined in detail. From the microstructural examination of peak-aged and deformed samples, it could be inferred that the dislocation-precipitate interaction is by precipitate shearing. Increased work hardening of the material in the overaged condition was suggestive of looping of precipitates by dislocations.

  6. Magnetic properties of maraging steel in relation to deformation and structural phase transformations

    SciTech Connect

    Ahmed, M.; Ali, A.; Hashmi, F.; Khan, A.Q. ); Hasnain, S.K. . Dept. of Physics)

    1994-03-01

    Magnetic properties in annealed and cold rolled conditions have been investigated for maraging steel grade 18%Ni-2,400. The austenite content, coercive field, saturation magnetization and remanence were determined after aging for 1 h in the temperature range from 400 to 800 C. The results show that the degree of deformation imparted to martensite influences both the amount of reverted austenite and the magnetic properties obtained following aging. Transmission electron microscopy was carried out in order to investigate the structural changes taking place during reversion of austenite.

  7. Effects of Aging Structures and Humidity on Fatigue Properties of Maraging Steel

    NASA Astrophysics Data System (ADS)

    Hayashi, Kousuke; Nagano, Takanori; Moriyama, Michihiko; Wang, Xishu; Kawagoishi, Norio

    Effects of aging structures and humidity on fatigue properties of 350 grade 18% Ni maraging steel were investigated under rotating bending in relative humidity of 25% and 85%. Aging conditions tested were a conventional single aging and a double one which was aged at low temperature after the conventional aging. In each aging, under and peak aged steels were prepared. Tensile strength was increased by the double aging without reduction of the ductility. Proportional relation between fatigue limit and Vickers hardness held until 750HV in low humidity. However fatigue strength was largely decreased by high humidity, especially in the peak aged steel at the single aging. The decrease in fatigue strength by high humidity was mainly caused by the acceleration of a crack initiation due to the anodic dissolution. The acceleration of a crack initiation was larger in the steel peak aged at the single aging with larger precipitated particles.

  8. Machining-induced deformation in stepped specimens of PH 13-8 Mo, 18 nickel maraging steel grade 200T1 and grain-refined HP 9-4-20

    NASA Technical Reports Server (NTRS)

    Wigley, D. A.

    1985-01-01

    The results of a study to evaluate the dimensional changes created during machining and subsequent cycling to cryogenic temperatures for three different metallic alloys are presented. Experimental techniques are described and results presented for 18 Ni Grade 200 maraging steel, PH-13-8 Mo stainless steel, and Grain-refined HP 9-4-20.

  9. Braze alloy process and strength characterization studies for 18 nickel grade 200 maraging steel with application to wind tunnel models

    NASA Technical Reports Server (NTRS)

    Bradshaw, James F.; Sandefur, Paul G., Jr.; Young, Clarence P., Jr.

    1991-01-01

    A comprehensive study of braze alloy selection process and strength characterization with application to wind tunnel models is presented. The applications for this study include the installation of stainless steel pressure tubing in model airfoil sections make of 18 Ni 200 grade maraging steel and the joining of wing structural components by brazing. Acceptable braze alloys for these applications are identified along with process, thermal braze cycle data, and thermal management procedures. Shear specimens are used to evaluate comparative shear strength properties for the various alloys at both room and cryogenic (-300 F) temperatures and include the effects of electroless nickel plating. Nickel plating was found to significantly enhance both the wetability and strength properties for the various braze alloys studied. The data are provided for use in selecting braze alloys for use with 18 Ni grade 200 steel in the design of wind tunnel models to be tested in an ambient or cryogenic environment.

  10. Elastic constant versus temperature behavior of three hardened maraging steels

    NASA Technical Reports Server (NTRS)

    Ledbetter, H. M.; Austin, M. W.

    1985-01-01

    Elastic constants of three maraging steels were determined by measuring ultrasonic velocities. Annealed steels show slightly lower bulk moduli and considerably lower shear moduli than hardened steels. All the elastic constants (Young's modulus, shear modulus, bulk modulus and Poisson's ratio) show regular temperature behavior between 76 and 400 K. Young's modulus and the shear modulus increase with increasing yield strength, but the bulk modulus and Poisson's ratio are relatively unchanged. Elastic anisotropy is quite small.

  11. Stabilization of small deformations of maraging steels by stress relaxation

    SciTech Connect

    Alekseeva, L.E.; Koritskaya, G.I.; Talalakina, E.I.

    1988-05-01

    The possibility of increasing the forming accuracy with small degrees of deformation of maraging steel by aging of it under stress after deformation was investigated. Aging under stress of water hardened VNS-2 maraging steel was done in the elastic area and after deformation to epsilon = 6% at 450/degree/: No. 12, (Dec 1987)C, a temperature corresponding to the maximum degree of dispersion hardening. The influence of the degree of deformation on the mechanical properties of the steel, the residual deformation, and stabilization of the ratio of the residual to the total deformations were determined. The structural condition of the martensite and the degree of solid solution decomposition were studied by x-ray diffraction analysis. The proposed treatment led to complete stabilization of the specified deformations with simultaneous strengthening and made it possible to obtain high accuracy in production of small curvature parts.

  12. Experimental investigation and statistical optimisation of the selective laser melting process of a maraging steel

    NASA Astrophysics Data System (ADS)

    Casalino, G.; Campanelli, S. L.; Contuzzi, N.; Ludovico, A. D.

    2015-01-01

    Selective Laser Melting (SLM) is an Additive Manufacturing process (AM) that built parts from powder using a layer-by-layer deposition technique. The control of the parameters that influence the melting and the amount of energy density involved in the process is paramount in order to get valuable parts. The objective of this paper is to perform an experimental investigation and a successive statistical optimization of the parameters of the selective laser melting process of the 18Ni300 maraging steel. The experimental investigation involved the study of the microstructure, the mechanical and surface properties of the laser maraging powder. The outcomes of experimental study demonstrated that the hardness, the mechanical strength and the surface roughness correlated positively to the part density. Parts with relative density higher than 99% had a very low porosity that presented closed and regular shaped pores. The statistical optimization determined that the best part properties were produced with the laser power bigger than 90 W and the velocity smaller than 220 mm/s.

  13. The maraging-steel blades of the Virgo super attenuator

    NASA Astrophysics Data System (ADS)

    Braccini, S.; Casciano, C.; Cordero, F.; Corvace, F.; DeSanctis, M.; Franco, R.; Frasconi, F.; Majorana, E.; Paparo, G.; Passaquieti, R.; Rapagnani, P.; Ricci, F.; Righetti, D.; Solina, A.; Valentini, R.

    2000-05-01

    The blades are crucial components of the Virgo super attenuators. The material used for their construction is maraging steel, a low-carbon-content alloy with high ultimate tensile strength and low creep under stress. Young's modulus, the shear modulus, the Poisson ratio and the corresponding elastic energy-loss coefficients have been measured. The measurements have been performed on specimens subjected to the same thermal treatments as those of elements for the Virgo interferometer realized with maraging steel. In addition, anelastic properties of the material subjected to different thermal treatments have been measured. It has been found that, for a maraging-steel structure (one free of plastic deformation), which undergoes an excitation with flexural vibrations, the elastic energy-loss coefficient can vary over a wide range as a function of the thermal treatment of the material and it is dominated by the thermo-elastic effect. The main reason for such a great alteration is supposed to be the dependence of the thermal conductivity on the average sizes of the precipitate particles and their relative separations.

  14. Structural strength of welded shells made of corrosion-resistant maraging steels

    SciTech Connect

    Raimond, E.D.; Lapin, P.G.; Pautkin, U.S.; Shiganov, N.V.; Tashchikov, V.S.

    1986-03-01

    The authors devise special measures to increase the resistance of welded shells made of corrosion-resistant maraging steels. High structural strenght is ensured for shells loaded by internal pressure when ait (impact toughness) greater than or equal to10 J/cm/sup 2/. For welds of corrosion-resistant maraging steels of the O3Kh11N10M2T type, this condition is satisfied when the weld strength does not exceed 1400-1450 MPa. A structural strength of 15001750 MPa in welds of corrosion-resistant maraging steels can be obtained by means of mechanicothermal treatment.

  15. Acoustic emission testing of 12-nickel maraging steel pressure vessels

    NASA Technical Reports Server (NTRS)

    Dunegan, H. L.

    1973-01-01

    Acoustic emission data were obtained from three point bend fracture toughness specimens of 12-nickel maraging steel, and two pressure vessels of the same material. One of the pressure vessels contained a prefabricated flaw which was extended and sharpened by fatigue cycling. It is shown that the flawed vessel had similar characteristics to the fracture specimens, thereby allowing estimates to be made of its nearness to failure during a proof test. Both the flawed and unflawed pressure vessel survived the proof pressure and 5 cycles to the working pressure, but it was apparent from the acoustic emission response during the proof cycle and the 5 cycles to the working pressure that the flawed vessel was very near failure. The flawed vessel did not survive a second cycle to the proof pressure before failure due to flaw extension through the wall (causing a leak).

  16. Nanoscale precipitation in a maraging steel studied by APFIM.

    PubMed

    Stiller, Krystyna; Hättestrand, Mats

    2004-06-01

    This article summarizes findings from our previous investigations and recent studies concerning precipitation in a maraging steel of type 13Cr-9Ni-2Mo-2Cu (at.%) with small additions of Ti (1 at.%) and Al (0.7 at.%). The material was investigated after aging at 475 degrees C up to 400 h using both conventional and three-dimensional atom-probe analyses. The process of phase decomposition in the steel proved to be complicated. It consisted of precipitation of several phases with different chemistry. A Cu-rich phase was first to precipitate and Mo was last in the precipitation sequence. The influence of the complex precipitation path on the material properties is discussed. The investigation clearly demonstrated the usefulness of the applied techniques for investigation of nanoscale precipitation. It is also shown that, complementary methods (such as TEM and EFTEM) giving structural and chemical information on a larger scale must be applied to explain the good properties of the steel after prolonged aging.

  17. Precipitation in 9Ni-12Cr-2Cu maraging steels

    SciTech Connect

    Stiller, K.; Haettestrand, M.; Danoix, F.

    1998-11-02

    Two maraging steels with the compositions 9Ni-12Cr-2Cu-4Mo (wt%) and 9Ni-12Cr-2Cu and with small additions of Al and Ti were investigated using atom probe field ion microscopy. Tomographic atom probe investigations were performed to clarify the spatial distribution of elements in and close to the precipitates. Materials heat treated at 475 C for 5, 25 min, 1, 2, 4 and 400 h were analyzed. Precipitates in the Mo-rich material were observed already after 5 min of aging, while in the material without MO, precipitation started later. In both materials precipitation begins with the formation of Cu-rich particles which work as nucleation sites for a Ni-rich phase of type Ni{sub 3}(Ti,Al). A Mo-rich phase was detected in the Mo-rich steel after 2 h of aging. The distribution of alloying elements in the precipitates, their role in the precipitation process, and the mechanism of hardening in the two materials are discussed.

  18. Ion-nitriding of Maraging steel (250 Grade) for Aeronautical application

    NASA Astrophysics Data System (ADS)

    Shetty, K.; Kumar, S.; Rao, P. R.

    2008-03-01

    Ion nitriding is one of the surface modification processes to obtain better wear resistance of the component. Maraging steel (250 Grade) is used to manufacture a critical component in the control surface of a combat aircraft. This part requires high strength and good wear resistance. Maraging steels belong to a new class of high strength steels with the combination of strength and toughness that are among the highest attainable in general engineering alloys. Good wear resistance is achieved by ion-nitriding (also called as plasma nitriding or glow discharge nitriding) process of case nitriding. Ion-nitriding is a method of surface hardening using glow discharge technology to introduce nascent (elemental) nitrogen to the surface of a metal part for subsequent diffusion into the material. In the present investigation, ion-nitriding of Maraging steel (250 grade) is carried out at 450°C and its effect on microstructure and various properties is discussed.

  19. Effect of superrapid crystallization on the structure and properties of maraging steels

    SciTech Connect

    Chernysheva, T.A.; Lyul'kina, T.V.; Kalita, V.I.; Kobylkin, A.N.; Revyakina, O.K.

    1988-07-01

    Results are presented for a study of the features of the structure and properties of industrial maraging steel 01N17K12M5T prepared with superrapid crystallization of the melt. It is shown that superrapid crystallization of melts for maraging steels has a considerable effect on the nature of their phase transformation, structures, and properties. Depending on solidification rate and subsequent cooling it is possible to form in the steel, structures of the following types: entirely martensitic; entirely ferritic; a mixture of martensitic and austenitic components.

  20. Acoustic emission during tensile deformation of M250 grade maraging steel

    NASA Astrophysics Data System (ADS)

    Mukhopadhyay, Chandan Kumar; Rajkumar, Kesavan Vadivelu; Chandra Rao, Bhaghi Purna; Jayakumar, Tamanna

    2012-05-01

    Acoustic emission (AE) generated during room temperature tensile deformation of varyingly heat treated (solution annealed and thermally aged) M250 grade maraging steel specimens have been studied. Deformation of microstructure corresponding to different heat treated conditions in this steel could be distinctly characterized using the AE parameters such as RMS voltage, counts and peak amplitude of AE hits (events).

  1. Precipitation evolution in a Ti-free and Ti-containing stainless maraging steel.

    PubMed

    Schober, M; Schnitzer, R; Leitner, H

    2009-04-01

    Stainless maraging steels have a Cr content higher than 12wt% and show a excellent combination of high strength and ductility, which make them attractive for use in machinery fields and aircraft applications. The massive increase of strength during ageing treatment of maraging steels is related to a precipitation sequence of various nm-scaled intermetallic phases. The peak hardness especially in Ti-containing maraging steels can be reached after short-time ageing at temperatures around 500 degrees C. However, precipitation reactions in different stainless maraging steels are not fully understood, especially the evolution from clustering over growing to coarsening. In the present work a commercial maraging steel and a Ti-containing model alloy are investigated and compared to each other. The steels were isothermally heat treated at 525 degrees C for a range of times. Special emphasis was laid on the correlation of hardness to the formation and presence of different kinds of precipitates. The isothermal aged samples were investigated by using two advanced three-dimensional energy compensated atom probes (LEAP and 3DAP) both in voltage mode and in laser mode. The atom probe data were correlated to standard hardness measurements. The results show that the partial substitution of Al by Ti results in a different precipitation behaviour. While the Ti-free maraging steel exhibit only one type of precipitate, the Ti-containing grade shows a change in the type of precipitates during ageing. However, this change leads to an accelerated coarsening and thus to a faster drop in hardness.

  2. Precipitation in 18 wt% Ni maraging steel of grade 350

    SciTech Connect

    Tewari, R.; Mazumder, S.; Batra, I.S.; Dey, G.K.; Banerjee, S.

    2000-03-14

    The evolution of precipitates in maraging steel of grade 350 was studied using the complementary techniques of small angle X-ray scattering (SACS) and transmission electron microscopy (TEM). These investigations revealed that ageing the steel at 703 K involved a rhombohedral distortion of the supersaturated b.c.c. martensite accompanied by the appearance of diffuse {omega}-like structures. This was followed by the appearance of well-defined {omega} particles containing chemical order. At the ageing temperature of 783 K, Ni{sub 3}(Ti,Mo) precipitates were the first to appear with a growth exponent of 1/3. The values of the Pored exponent obtained from the SAXS profiles indicated that the {omega} particles, formed below 723 K, had diffuse interfaces up to an ageing time of 48 h. On the other hand, Ni{sub 3}(Ti,Mo) precipitates, formed above 723 K, developed sharp interfaces in just about an hour. Also, the steel exhibited scaling in phase separation both at 703 and 783 K, but only during the early stages. Through this study it was established that at temperatures of ageing less than 723 K, evolution of {omega} particles takes place through the collapse of the unstable b.c.c. lattice and, at temperatures above 723 K, precipitation of A{sub 3}B type of phases through the mechanism of clustering and ordering of atomic species. Sharp interfaces develop rather quickly when the mechanism of precipitation involves development and amplification of a concentration wave along as in the nucleation of Ni{sub 3}(Ti,Mo) at 783 K than when an interplay of both the displacement and concentration waves is required as in the evolution of {omega} at 703 K. These results indicate towards the possibility of existence of two separate time-temperature-transformation (TTT) curves, one for the evolution of {omega}-phase and another for nucleation and growth of Ni{sub 3}(Ti,Mo).

  3. Ultrasonic Characterization of Aging Behavior in M250 Grade Maraging Steel

    NASA Astrophysics Data System (ADS)

    Yeheskel, Ori

    2009-03-01

    The increase in sound velocities during the aging of M250 maraging steel reported by Rajkumar et al. was analyzed. The present article provides a new perspective on why and to what extent the sound velocities change during aging. The main parameter that affects the elastic moduli and the sound velocities in the early and intermediate stages of aging in maraging steel is the depletion of Ni from the martensitic matrix due to Ni3Ti and Ni3Mo formation. The issue of sound velocity increase with aging time was addressed here in a few different ways to support the validity of Ni depletion.

  4. Hydrogen embrittlement of duplex stainless steel and maraging steel in sea water: Effect of pressure

    SciTech Connect

    Pohjanne, P.; Festy, D.

    1994-12-31

    Hydrogen embrittlement behavior of cast super duplex stainless steel and cast maraging steel was examined as a function of electrode potential and hydrostatic pressure, i.e, the water depth, in synthetic sea water using fracture mechanics bolt-loaded wedge-opening (WOL) specimens. The experimental variables investigated included: (1) Electrode potential: free corrosion potential and cathodic protection; (2) Hydrostatic pressure: ambient and 10 MPa corresponding depth of 1,000 meters. The duplex stainless-,steel was not susceptible to hydrogen embrittlement with initial stress intensity values of 30 MPa{radical}m < K{sub i} < 45 MPa{radical}m at ambient pressure. However, at pressure of 10 MPa slight crack growth was observed at open circuit potential and the crack growth was enhanced by the cathodic protection. The maraging steel was susceptible to hydrogen embrittlement in all tests, with all examined initial stress intensity values, K{sub i} < 36 MPa{radical}m. At the open circuit potential the crack growth rate was almost independent of the pressure. Cathodic protection enhanced crack growth and lowered the threshold stress intensity value at ambient as well as at 10 MPa pressure and the crack growth rate increased clearly as pressure increased from 0.1 MPa to 10 MPa. According to these experimental results the combined effect of cathodic protection and hydrostatic pressure must be taken into consideration when designing new offshore structures and equipment especially for deep sea application.

  5. Characterization of aging-induced microstructural changes in M250 maraging steel using magnetic parameters

    NASA Astrophysics Data System (ADS)

    Rajkumar, K. V.; Vaidyanathan, S.; Kumar, Anish; Jayakumar, T.; Raj, Baldev; Ray, K. K.

    2007-05-01

    The best combinations of mechanical properties (yield stress and fracture toughness) of M250 maraging steel is obtained through short-term thermal aging (3-10 h) at 755 K. This is attributed to the microstructure containing precipitation of intermetallic phases in austenite-free low-carbon martensite matrix. Over-aged microstructure, containing reverted austenite degrades the mechanical properties drastically. Hence, it necessitates identification of a suitable non-destructive evaluation (NDE) technique for detecting any reverted austenite unambiguously during aging. The influence of aging on microstructure, room temperature hardness and non-destructive magnetic parameters such as coercivity ( Hc), saturation magnetization ( Ms) and magnetic Barkhausen emission (MBE) RMS peak voltage is studied in order to derive correlations between these parameters in aged M250 maraging steel. Hardness was found to increase with precipitation of intermetallics during initial aging and decrease at longer durations due to austenite reversion. Among the different magnetic parameters studied, MBE RMS peak voltage was found to be very sensitive to austenite reversion (non-magnetic phase) as they decreased drastically up on initiation of austenite reversion. Hence, this parameter can be effectively utilized to detect and quantify the reverted austenite in maraging steel specimen. The present study clearly indicates that the combination of MBE RMS peak voltage and hardness can be used for unambiguous characterization of microstructural features of technological and practical importance (3-10 h of aging duration at 755 K) in M250 grade maraging steel.

  6. Nanoscale evaluation of laser-based surface treated 12Ni maraging steel

    NASA Astrophysics Data System (ADS)

    Grum, J.; Slabe, J. M.

    2005-07-01

    Maraging steels are used in several high-tech areas. Among them are highly thermo-mechanically loaded vital parts of die casting dies for pressure die casting of aluminium and magnesium alloys. From the economic point of view, the operation life of dies is extremely important to the price of the castings. Operational life can be successfully extended by a regular maintenance of die parts. Laser surfacing is a very promising process for rebuilding of worn out surfaces of vital die parts. In this research, the state in the maraging steel 1.2799 (DIN) after the application of laser surfacing process has been analysed using scanning electron microscope. The analysis revealed diverse microstructure through-depth of the laser-surfaced specimens. On the basis of the estimated size and volume fraction of the nano-precipitates in the individual microstructure zones located through-depth of the heat-affected zone, a through-depth variation of microhardness was predicted. The results are supported by Vickers microhardness tests. It was confirmed that the mechanical properties of the 1.2799 maraging steel strongly depend on the characteristic at the nano or micro level. Some of the results obtained can be also applied to laser surface heat treatment of maraging steels.

  7. Characterization of Aging Behavior in M250 Grade Maraging Steel Using Ultrasonic Measurements

    NASA Astrophysics Data System (ADS)

    Rajkumar, K. V.; Kumar, Anish; Jayakumar, T.; Raj, Baldev; Ray, K. K.

    2007-02-01

    Ultrasonic measurements have been carried out in M250 grade maraging steel specimens subjected to solution annealing at 1093 K for 1 hour followed by aging at 755 K for various durations in the range of 0.25 to 100 hours. The influence of aging on microstructure, room temperature hardness, and ultrasonic parameters (longitudinal and shear wave velocities and Poisson’s ratio) has been studied in order to derive correlations among these parameters in aged M250 maraging steel. Both hardness and ultrasonic velocities exhibit almost similar behaviors with aging time. They increase with the precipitation of intermetallic phases, Ni3Ti and Fe2Mo, and decrease with the reversion of martensite to austenite. Ultrasonic shear wave velocity is found to be more influenced by the precipitation of intermetallic phases, whereas longitudinal wave velocity is influenced more by the reversion of martensite to austenite. Unlike hardness and ultrasonic velocities, the Poisson’s ratio exhibits a monotonous decrease with aging time and, hence, can be used for unambiguous monitoring of the aging process in M250 maraging steel. Further, none of the parameters, i.e., hardness, ultrasonic velocity, or Poisson’s ratio, alone could identify the initiation of the reversion of austenite at early stage; however, the same could be identified from the correlation between ultrasonic velocity and Poisson’s ratio, indicating the advantage of using the multiparametric approach for comprehensive characterization of complex aging behavior in M250 grade maraging steel.

  8. The formation of twinned austenite in Fe-10Cr-10Ni-2W maraging steel

    SciTech Connect

    Suk, J.I.; Hong, S.H.; Nam, S.W. )

    1991-12-01

    The precipitation hardening mechanisms in high strength maraging steels have been studied in detail by many investigators, but limited information is available on the formation of austenite during aging. Some investigations have been concerned with the understanding of the effect of reverted austenite formed during aging on the mechanical properties. However, only a few investigations have been reported on the morphology and crystallographic feature of austenite. Shiang and Wayman first reported the twin-related and coupled morphology of Widmanstatten austenite plates which were frequently observed in maraging steel. In addition, Ameyama et al. reported the morphology and crystallographic features of austenite formed in ferrite grain during aging in a two-phase stainless steel, and found that each side of the austenite pair of twins satisfies the Kurdjumov-Sachs (K-S) orientation relationship with the parent phase. The morphology and crystallographic features of the reverted austenite formed during aging of Fe-10Cr-10Ni-2W stainless maraging steel have been investigated in this paper. The major strengthening precipitate in Fe-10Cr-10Ni-2W maraging steels has been identified as the rod-shaped {eta}-Ni{sub 3}Ti phase in our previous study. The peculiar morphology of the austenite, i.e., twinned austenite, also has been found in our studies of maraging steel in the Fe-10Cr-10Ni-2W lath martensite. In addition, computer simulation of the diffraction pattern is used to confirm the orientation relationships, such as the Kurdjumov-Sachs (K-S) relationship, the Nishiyama-Wasserman (N-W) relationship and the twin relationship by comparisons with the experimentaly observed results.

  9. Determination of the plasticity of N18K9M5T maraging steel thin sheet

    SciTech Connect

    Shishov, V.F.

    1985-08-01

    This paper investigates the value of the nominal elongation of N18K9M5T maraging steel in relation to sheet thickness, structure of steel, and the specimen type. The characteristics of strength and plasticity determined in testing of cylindrical and flat specimens of the investigated steel is presented. The authors conclude that the total elongation of N18K9M5T maraging steel is its abnormally high capacity for plastic deformation in the formation of the neck. To obtain closer values of elongation in testing N18K9M5T steel thin sheet of different thicknesses, it is desirable to use specimens in which the ratio b/sub 0//alpha/sub 0/ is less than or equal to 4:1.

  10. Control of variation of properties of maraging chromium-nickel steels in long-term heating

    NASA Astrophysics Data System (ADS)

    Tarasenko, L. V.; Titov, V. I.; Elyutina, L. A.

    2010-11-01

    Variation of the phase composition and mechanical properties of maraging steels of the Fe - Cr - Ni - Mo - Ti system after heat treatment (hardening and aging) and long-term heating for up to 1500 h at a temperature of 400 - 450°C is studied. It is shown that the degree of variation of the properties of steels with different contents of titanium after long-term heating can be regulated by changing the mode of the aging.

  11. Raising the Structural Strength of Systematically Alloyed Fe - Cr - Ni - Mo-Base Maraging Steels

    NASA Astrophysics Data System (ADS)

    Gladkovskii, S. V.; Ishina, E. A.; Kuteneva, S. V.

    2016-03-01

    The effect of systematical Mo, Ti, Al and Ca alloying of corrosion-resistant maraging steels of type Kh11N10M2T and of the modes of their heat treatment on the phase composition, combination of properties and resistance to brittle fracture is studied. It is shown that the structural strength of the steels can be raised by additional alloying with copper and formation of a regulated content of metastable retained austenite.

  12. Phase chemistry and precipitation reactions in maraging steels: Part 2. Co-free T-300 steel

    SciTech Connect

    Sha, W. ); Cerezo, A.; Smith, G.D.W. . Department of Materials)

    1993-06-01

    This article describes studies of phase transformations during aging in a commercial Co-free T-300 maraging steel. Atom-probe field-ion microscopy (APFIM) was the main research technique employed. Thermochemical calculation was used to aid the interpretation of results. The composition and morphology of precipitates were compared in the same maraging system aged at different temperatures for different times to investigate the aging sequence. Ni[sub 3]Ti and Fe[sub 7]Mo[sub 6] have been found to contribute to age hardening. The formation of the Fe[sub 7]Mo[sub 6] phase took place at a much later stage of aging in the Co-free steel than in the equivalent Co-containing material. The matrix concentration of Mo was correspondingly higher at earlier stages of aging. No reverted austenite has been found during APFIM and transmission electron microscopy (TEM) examinations of specimens heat-treated at 510 [degree]C, even after 360 hours of aging.

  13. Effect of residual austenite on the tendency of incompletely aged maraging steels to embrittlement during slow deformation

    SciTech Connect

    Kardonskii, V.M.; Gorbunova, N.B.

    1986-03-01

    The authors investigate the high-strength maraging steels (HSMS) N17K10V10MT and N18V10V10MT by cyclic heat treatment and heating to temperatures of the dual-phase (alpha + gamma)-region. Embrittlement during the slow loading of incompletely aged HSMS with titanium can be reduced when approximately 20% of residual austenite is obtained in them. Maraging steel containing residual austenite in the initial state does not tend toward this type of embrittlement.

  14. Characterization of the behavior under impact loading of a maraging steel strengthened by nano-precipitates

    NASA Astrophysics Data System (ADS)

    Lach, E.; Redjaïmia, A.; Leitner, H.; Clemens, H.

    2006-08-01

    Nanometer-sized precipitates are responsible for the high strength of steel alloys well known as maraging steels. The term maraging relates to aging reactions in very low-carbon martensitic steels. Due to precipitation hardening 0.2% yield stress values of up to 2.4 GPa can be achieved. The class of stainless maraging steels exhibits an excellent combination of very high strength and hardness, ductility and toughness, combined with good corrosion resistance. In many applications like crash worthiness or ballistic protection the materials are loaded at high strain-rates. The most important characteristic of material behavior under dynamic load is the dynamic yield stress. In this work compression tests had been conducted at strain-rates in the order of 5 x 10 - 3 s - 1 up to 3 x 103 s - 1 to study the materials behaviour. Additionally high dynamic compression tests had been performed in the temperature range from -40circC up to 300circC.

  15. APPLYING TEP MEASUREMENTS TO ASSESS THE AGING STAGE OF MARAGING 250 STEEL

    SciTech Connect

    Snir, Y.; Gelbstein, Y.; Pinkas, M.; Yeheskel, O.; Landau, A.

    2008-02-28

    Thermoelectric power (TEP) measurements had been proved as an effective method for evaluating the metallurgical state of various alloys. The current work was conducted in order to evaluate the influence of the aging state of Maraging 250 steel on TEP values. Commercial Maraging 250 steel was aged at 500 deg. C for 0.5-6 hours (hrs). TEP, hardness (Rc) and ultrasonic (US) measurements, were preformed on the as received and aged specimens. XRD measurements were used to identify the formation of precipitates (mainly Ni{sub 3}(Ti,Mo)), reverted austenite and to evaluate changes in the microstrain caused by the precipitation process. A correlation was found between the TEP and the various measurements as a function of the aging time.

  16. Applying Tep Measurements to Assess the Aging Stage of Maraging 250 Steel

    NASA Astrophysics Data System (ADS)

    Snir, Y.; Pinkas, M.; Gelbstein, Y.; Yeheskel, O.; Landau, A.

    2008-02-01

    Thermoelectric power (TEP) measurements had been proved as an effective method for evaluating the metallurgical state of various alloys. The current work was conducted in order to evaluate the influence of the aging state of Maraging 250 steel on TEP values. Commercial Maraging 250 steel was aged at 500 °C for 0.5-6 hours (hrs). TEP, hardness (Rc) and ultrasonic (US) measurements, were preformed on the as received and aged specimens. XRD measurements were used to identify the formation of precipitates (mainly Ni3(Ti,Mo)), reverted austenite and to evaluate changes in the microstrain caused by the precipitation process. A correlation was found between the TEP and the various measurements as a function of the aging time.

  17. Dynamic Deformation Response of Maraging Steel Hollow Sphere and Aluminum Composite

    NASA Astrophysics Data System (ADS)

    Kennedy, Gregory; Scripka, David; Welchel, Ricky; Cochran, Joe; Sanders, Tom; Thadhani, Naresh

    2011-06-01

    The dynamic deformation response of a light-weight composite system consisting of maraging steel hollow spheres in an aluminum matrix is investigated. The composite system made by in-filtrating aluminum alloy melt around the high strength and toughness maraging steel hollow spheres, enables design of a light-weight energy-absorbing structural material. Rod-on-anvil Taylor impact tests are conducted to study the behavior of the composite material under uniaxial stress loading. The transient deformation states are captured using high-speed digital imaging for correlation with AUTODYN simulations. The recovered impacted samples are characterized using microscopy to determine the deformation response of the hollow spheres and the influence of the matrix-sphere interface on the overall properties of the composite material.

  18. Dynamic deformation and fragmentation response of maraging steel linear cellular alloy

    NASA Astrophysics Data System (ADS)

    Jakus, Adam E.; Fredenberg, David A.; McCoy, Tammy; Thadhani, Naresh; Cochran, Joe K.

    2012-03-01

    The dynamic deformation and fragmentation response of 25% dense 9-cell linear cellular alloy (LCA) made of unaged 250 maraging steel, fabricated using a direct reduction and extrusion technique, is investigated. Explicit finite element simulations were implemented using AUTODYN finite element code. The maraging steel properties were defined using a Johnson-Cook strength model with previously validated parameters. Rod-on-anvil impact tests were performed using the 7.6mm helium gas gun and the transient deformation and fragmentation response was recorded with highspeed imaging. Analysis of observed deformation states of specimens and finite element simulations reveal that in the case of the 9-cell LCA, dissipation of stress and strain occurs along the interior cell wells resulting in significant and ubiquitous buckling prior to confined fragmentation.

  19. Texture development in dual-phase cold-rolled 18 pct Ni maraging steel

    SciTech Connect

    Ahmad, Z.; Farooque, M.; Ul Haq, A.; Khan, A.Q.

    1997-12-01

    Austenite and martensite textures were studied in 18 pct Ni 350-maraging steel as a function of various degrees of cold rolling. The austenite phase in the samples was produced by repeated thermal cycling between ambient and 800 C. The austenite phase thus formed was mechanically unstable and transformed to the martensite phase after 30 pct cold rolling. The texture developed as a result of cold rolling, and its effect upon microstructure and hardness has been studied.

  20. Structure and Mechanical Properties of Maraging and Low-Carbon Martensitic Steels

    NASA Astrophysics Data System (ADS)

    Shvetsov, V. V.; Simonov, Yu. N.; Kleiner, L. M.

    2005-01-01

    The structure, mechanical properties, and crack resistance after tempering of maraging steel 03Kh11N10M2T (EP-678) and low-carbon martensitic steel 12Kh2G2NMFT are studied. The range of tempering temperatures ensuring the combination of properties required for massive parts (σr #x2265; 1300 MPa, σ0.2 ≥ 1100 MPa, KCT ≥ 0.2 MJ/m2) is determined. It is shown that steel 12Kh2G2NMFT is better adaptable to manufacture because it is hardened by air-cooling.

  1. Gaseous hydrogen embrittlement of steel - the rate controlling process

    SciTech Connect

    Pasco, R.W.; Ficalora, P.J.

    1981-09-01

    In 18Ni (250) and 18Ni (200) maraging steel, a simple model relates Stage II crack growth rates to adsorption kinetics. Crack growth kinetics are related to a critical volume concentration, c* (m/sup -3/), through which the crack advances once this concentration is attained. 11 refs.

  2. Microstructural Evolution and Constitutive Relationship of M350 Grade Maraging Steel During Hot Deformation

    NASA Astrophysics Data System (ADS)

    Chakravarthi, K. V. A.; Koundinya, N. T. B. N.; Narayana Murty, S. V. S.; Nageswara Rao, B.

    2017-03-01

    Maraging steels exhibit extraordinary strength coupled with toughness and are therefore materials of choice for critical structural applications in defense, aerospace and nuclear engineering. Thermo-mechanical processing is an important step in the manufacture of these structural components. This process assumes significance as these materials are expensive and the mechanical properties obtained depend on the microstructure evolved during thermo-mechanical processing. In the present study, M350 grade maraging steel specimens were hot isothermally compressed in the temperature range of 900-1200 °C and in the strain rate range of 0.001-100 s-1, and true stress-true strain curves were generated. The microstructural evolution as a function of strain rate and temperature in the deformed compression specimens was studied. The effect of friction between sample and compression dies was evaluated, and the same was found to be low. The measured flow stress data was used for the development of a constitutive model to represent the hot deformation behavior of this alloy. The proposed equation can be used as an input in the finite element analysis to obtain the flow stress at any given strain, strain rate, and temperature useful for predicting the flow localization or fracture during thermo-mechanical simulation. The activation energy for hot deformation was calculated and is found to be 370.88 kJ/mol, which is similar to that of M250 grade maraging steel.

  3. Microstructural Evolution and Constitutive Relationship of M350 Grade Maraging Steel During Hot Deformation

    NASA Astrophysics Data System (ADS)

    Chakravarthi, K. V. A.; Koundinya, N. T. B. N.; Narayana Murty, S. V. S.; Nageswara Rao, B.

    2017-02-01

    Maraging steels exhibit extraordinary strength coupled with toughness and are therefore materials of choice for critical structural applications in defense, aerospace and nuclear engineering. Thermo-mechanical processing is an important step in the manufacture of these structural components. This process assumes significance as these materials are expensive and the mechanical properties obtained depend on the microstructure evolved during thermo-mechanical processing. In the present study, M350 grade maraging steel specimens were hot isothermally compressed in the temperature range of 900-1200 °C and in the strain rate range of 0.001-100 s-1, and true stress-true strain curves were generated. The microstructural evolution as a function of strain rate and temperature in the deformed compression specimens was studied. The effect of friction between sample and compression dies was evaluated, and the same was found to be low. The measured flow stress data was used for the development of a constitutive model to represent the hot deformation behavior of this alloy. The proposed equation can be used as an input in the finite element analysis to obtain the flow stress at any given strain, strain rate, and temperature useful for predicting the flow localization or fracture during thermo-mechanical simulation. The activation energy for hot deformation was calculated and is found to be 370.88 kJ/mol, which is similar to that of M250 grade maraging steel.

  4. Isothermal formation of martensite in a 12Cr-9Ni-4Mo maraging stainless steel

    SciTech Connect

    Holmquist, M.

    1995-11-01

    The present paper is concerned with the nature of the martensite, which provides the basis for the maraging treatment. Rather than forming martensite during cooling, 1RK91 develops martensite when held at a constant temperature in a range from room temperature and below. Isothermal martensite formation showing C-curve kinetics was found to occur in the maraging steel 1RK91, the nose temperature being about {minus}40 C. The kinetics was found to be enhanced for higher austenitizing treatment temperatures, presumably through a combination of larger grain size and a larger number of quenched in nuclei for isothermal martensite transformation. Experiments involving different cooling rates showed that fast cooling enhanced the transformation kinetics. Based on this observation it is suggested that quenched-in vacancy clusters provide suitable strain embryos for isothermal martensite nucleation.

  5. Influence of banded structure on the mechanical properties of a high-strength maraging steel

    SciTech Connect

    Ahmed, M.; Salam, I.; Hashmi, F.H.; Khan, A.Q.

    1997-04-01

    Chemical inhomogeneity results in the formation of banded structure in high-strength maraging steels. Segregation of titanium and molybdenum was found to be the primary cause of banded structure formation. When the concentrations of these elements increased beyond certain critical levels, bands comprising different grain sizes formed. The inclusions existed preferentially along the interface of the bands. A high-temperature homogenization treatment substantially reduced or eliminated the banded structure. The large grain size resulting from the homogenization treatment was subsequently reduced by a grain refinement treatment. The mechanical properties of the steel substantially improved following homogenization and grain refinement.

  6. Austenite layer and precipitation in high Co-Ni maraging steel.

    PubMed

    Wang, Chenchong; Zhang, Chi; Yang, Zhigang

    2014-12-01

    In high Co-Ni maraging steel, austenite has a great effect on the fracture toughness of the steel and the precipitated carbides are the main strengthening phase. In this study, both austenite layers and precipitation were observed and their formation theory was analyzed by Thermo-Calc simulation and several reported results. TEM and HRTEM observation results showed that the thickness of the austenite layers was about 5-10 nm and the length of the needle-like precipitated carbides was less than 10nm. The carbides maintained coherent or semi-coherent relation with the matrix.

  7. Microstructure Characterization and Corrosion Resistance Behavior of New Cobalt-Free Maraging Steel Produced Through ESR Techniques

    NASA Astrophysics Data System (ADS)

    Seikh, Asiful H.; Halfa, Hossam; Baig, Muneer; Khan, Sohail M. A.

    2017-03-01

    In this study, two different grades (M23 and M29) of cobalt-free low nickel maraging steel have been produced through electroslag remelting (ESR) process. The corrosion resistance of these ESR steels was investigated in 1 M H2SO4 solution using linear potentiodynamic polarization (LPP) and electrochemical impedance spectroscopy (EIS) techniques. The experiments were performed for different immersion time and solution temperature. To evaluate the corrosion resistance of the ESR steels, some significant characterization parameters from LPP and EIS curves were analyzed and compared with that of conventional C250 maraging steel. Irrespective of measurement techniques used, the results show that the corrosion resistance of the ESR steels was higher than the C250 steel. The microstructure of ESR steels was composed of uniform and well-distributed martensite accompanied with little amount of retained austenite in comparison with C250 steel.

  8. Microstructure and Mechanical Properties of Mn-Containing Maraging Steels

    NASA Astrophysics Data System (ADS)

    Hamed Zargari, Habib; Hossein Nedjad, Syamak

    2015-09-01

    An attempt to the modification of the microstructure and mechanical properties of affordable, Mn-containing maraging alloys is reported. These alloys have demonstrated strong age hardening but suffered with premature intergranular brittleness despite their potential applications in tooling, dies, and machinery industries. An Fe-10Ni-6Mo-3Mn-1Ti (wt.%) alloy was prepared by vacuum melting and processed by homogenization (1250 °C/48 h), cold rolling, solution annealing (950 °C/1 h), and aging treatments (500 °C/4 h). It presented tensile strength of about 2.65 GPa, a few percent of tensile elongation and a mixed ductile-brittle fracture mode. Transmission electron microscopy (TEM) revealed the precipitation of a nearly spherical phase. Crystal symmetry of the second phase precipitates was identified hexagonal close-packed corresponding reasonably to the Fe2Mo Laves phase having lattice parameters of a = 0.4745 and c = 0.7754 nm. Precipitation of a Mo-enriched second-phase particle was occasionally found at prior austenite grain boundaries but the pronounced grain boundary precipitation was never identified. Energy-filtering transmission electron microscopy using the Mo-M4,5 post edge revealed remarkable segregation of Mo at grain boundaries.

  9. A dilatometric study of the continuous heating transformations in maraging 300 steel

    NASA Astrophysics Data System (ADS)

    Reis, A. G.; Reis, D. A. P.; Abdalla, A. J.; Otubo, J.; Sandim, H. R. Z.

    2015-11-01

    Dilatometric study in maraging 300 steel was carried out to study the effect of heating rate on precipitation of intermetallic phases and martensite to austenite transformation. Solution annealed material were subjected to controlled heating-holding-cooling cycles. The martensite to austenite transformation splits into two steps at lower heating rates. The first step enhanced by slow heating rate, occurs through a diffusion process, while the second step, enhanced by a fast heating rate, occurs though a shear process. The extent of precipitation decreases with heating rate, suggesting that precipitation occurs primarily by a diffusional process.

  10. Phase chemistry and precipitation reactions in maraging steels: Part 3. Model alloys

    SciTech Connect

    Sha, W. .Department of Materials Science and Metallurgy); Cerezo, A.; Smith, G.D.W. . Department of Materials)

    1993-06-01

    This article describes studies of phase transformations during aging in a variety of model maraging steels. Atom-probe field-ion microscopy (APFIM) was the main research technique employed. Thermochemical calculation was also used during the course of the work. The composition and morphology of precipitates were compared in several maraging systems aged at different temperatures for different times to investigate the aging sequence. The APFIM results are compared with studies by other workers using different experimental techniques. In Fe-Ni(-Co)-Mo model alloys, [omega] phase and Fe[sub 7]Mo[sub 6] [mu] phase have been found to contribute to age hardening at different stages of aging; no evidence was found for the existence of Mo-rich clusters in the as-quenched Fe-Ni-Co-Mo alloy. In a high-Si Cr-containing steel, Ti[sub 6]Si[sub 7]Ni[sub 16]G phase and Ni[sub 3]Ti have been found to contribute to age hardening; reverted austenite was found after aging for 5 hours at 520 [degree]C. In a Mn-containing steel, Fe[sub 2]Mo Laves phase and a structurally uncertain phase with a composition of Fe[sub 45]Mn[sub 32]Co[sub 5]Mo[sub 19] have been found to contribute to age hardening.

  11. Investigation into Microstructures of Maraging Steel 250 Weldments and Effect of Post-Weld Heat Treatments

    NASA Astrophysics Data System (ADS)

    Tariq, Fawad; Baloch, Rasheed Ahmed; Ahmed, Bilal; Naz, Nausheen

    2010-03-01

    This study was undertaken to gain a better understanding of microstructures obtained by multipass gas tungsten arc welding in maraging steel grade 250. Metallography and microhardness measurements were carried out on sheet and welded joints in as-welded and post-weld aged conditions. It was found that there was a significant amount of reverted austenite formed on cell boundaries of weld metal after aging at 758-823 K for 3-5 h, and was stable at room temperature. Aging at higher temperatures led to an increase in the continuous network of patchy austenite along the cell boundaries. The reason for the above, in our opinion, is the concentrational heterogeneity which characterizes the microstructure of maraging steel welds. No reverted austenite was observed in as-welded specimens. Solution annealing at 1093 K for 1 h did not completely eliminate the chemical heterogeneity associated with weld structures. However, homogenizing at 1373 K produced homogenous structure that on subsequent aging produces austenite-free lath martensitic structure.

  12. Dynamic Deformation and Fragmentation Response of Maraging Steel Linear Cellular Alloy

    NASA Astrophysics Data System (ADS)

    Jakus, Adam; Fredenburg, D. A.; McCoy, T.; Thadhani, N. N.; Cochran, J.

    2011-06-01

    The dynamic deformation and fragmentation response of 25% dense 9-cell linear cellular alloy (LCA) made of unaged 250 maraging steel, fabricated using a direct reduction and extrusion technique, is investigated. Explicit finite element simulations were implemented using AUTODYN. The maraging steel properties were defined using a Johnson-Cook strength model with previously validated parameters. Rod-on-anvil impact tests were performed using the 7.6 mm helium gas gun and the transient deformation and fragmentation response was recorded with high-speed imaging. For purpose of comparison, the response of 25% dense hollow cylinders of same density as the 9-cell LCA was also studied. Analysis of observed states of specimens and finite element simulations reveal that in the case of the 9-cell LCA, dissipation of stress and strain occurs along the interior cell wells resulting in significant and ubiquitous buckling prior to confined fragmentation. In comparison, the simple hollow cylinder undergoes significant radial lipping, eventually producing larger sized, external fragments. DTRA Grant No. HDTRA1-07-1-0018 and NDSEG Fellowship Program.

  13. Hydrogen adsorption and diffusion, and subcritical-crack growth in high-strength steels and nickel base alloys

    NASA Technical Reports Server (NTRS)

    Wei, R. P.; Klier, K.; Simmons, G. W.

    1974-01-01

    Coordinated studies of the kinetics of crack growth and of hydrogen adsorption and diffusion were initiated to develop information that is needed for a clearer determination of the rate controlling process and possible mechanism for hydrogen enhanced crack growth, and for estimating behavior over a range of temperatures and pressures. Inconel 718 alloy and 18Ni(200) maraging steel were selected for these studies. 18Ni(250) maraging steel, 316 stainless steel, and iron single crystal of (111) orientation were also included in the chemistry studies. Crack growth data on 18Ni(250) maraging steel from another program are included for comparison. No sustained-load crack growth was observed for the Inconel 718 alloy in gaseous hydrogen. Gaseous hydrogen assisted crack growth in the 18Ni maraging steels were characterized by K-independent (Stage 2) extension over a wide range of hydrogen pressures (86 to 2000 torr or 12 kN/m2 to 266 kN/m2) and test temperatures (-60 C to +100 C). The higher strength 18Ni(250) maraging steel was more susceptible than the lower strength 200 grade. A transition temperature was observed, above which crack growth rates became diminishingly small.

  14. Influence of nickel and molybdenum on the phase stability and mechanical properties of maraging steels

    SciTech Connect

    Ahmed, M.; Nasim, I.; Husain, S.W. )

    1994-04-01

    The effect of nickel and molybdenum concentrations on the phase transformation and mechanical properties of conventional 10Ni(350) maraging steel has been investigated. Both of these elements act as strong austenite stabilizers. When the concentration of molybdenum or nickel is greater than 7.5 or 24 wt%, respectively, the austenite phase remains stable up to room temperature. In both molybdenum- and nickel-alloyed steels, the austenite phase could be transformed to martensite by either dipping the material in liquid nitrogen or subjecting it to cold working. When 7.5 wt% Mo and 24 wt% Ni were added in combination, however, the austenite phase obtained at room temperature did not transform to martensite when liquid-nitrogen quenched or even when cold rolled to greater than 95% reduction. The aging response of these materials has also been investigated using optical, scanning electron, and scanning transmission electron microscopy.

  15. Effect of thermal cycling on the mechanical properties of 350-grade maraging steel

    SciTech Connect

    Viswanathan, U.K.; Kishore, R.; Asundi, M.K.

    1996-03-01

    The effects of retained austenite produced by thermal cycling on the mechanical properties of a precipitation-hardened 350-grade commercial maraging steel were examined. The presence of retained austenite caused decreases in the yield strength (YS) and ultimate tensile strength (UTS) and effected a significant increase in the tensile ductility. Increased impact toughness was also produced by this treatment. The mechanical stability of retained austenite was evaluated by tension and impact tests at subambient temperatures. A deformation-induced transformation of the austenite was manifested as load drops on the load-elongation plots at subzero temperatures. This transformation imparts excellent low-temperature ductility to the material. A wide range of strength, ductility, and toughness can be obtained by subjecting the steel to thermal cycling before the precipitation-hardening treatment.

  16. Maraging-350 steel: Following the aging through diffractometric, magnetic and hyperfine analysis

    NASA Astrophysics Data System (ADS)

    Nunes, G. C. S.; Sarvezuk, P. W. C.; Alves, T. J. B.; Biondo, V.; Ivashita, F. F.; Paesano, A.

    2017-01-01

    Plates of solution annealed Maraging-350 steel were submitted to aging under an inert atmosphere, varying the time and temperature. The aged samples were characterized by X-ray diffraction and Mössbauer spectroscopy. The results revealed that the aging treatments induced the reversion of austenite, in amounts that vary with the time and the temperature of the heat treatment. The lattice parameters of the martensite and austenite phases, as well as their hyperfine parameters, were obtained at all aging conditions. No intermetallic compounds were identified in any of the aged samples, but a poorly crystallized phase fraction, the consequence of an incomplete martensite ⇒ austenite reversion transformation, was observed for some samples. The tetragonal distortion from cubic symmetry presented by the martensite in the solution annealed steel was not eliminated after aging.

  17. Optimization of process parameters of pulsed TIG welded maraging steel C300

    NASA Astrophysics Data System (ADS)

    Deepak, P.; Jualeash, M. J.; Jishnu, J.; Srinivasan, P.; Arivarasu, M.; Padmanaban, R.; Thirumalini, S.

    2016-09-01

    Pulsed TIG welding technology provides excellent welding performance on thin sections which helps to increase productivity, enhance weld quality, minimize weld costs, and boost operator efficiency and this has drawn the attention of the welding society. Maraging C300 steel is extensively used in defence and aerospace industry and thus its welding becomes an area of paramount importance. In pulsed TIG welding, weld quality depends on the process parameters used. In this work, Pulsed TIG bead-on-plate welding is performed on a 5mm thick maraging C300 plate at different combinations of input parameters: peak current (Ip), base current (Ib) and pulsing frequency (HZ) as per box behnken design with three-levels for each factor. Response surface methodology is utilized for establishing a mathematical model for predicting the weld bead depth. The effect of Ip, Ib and HZ on the weld bead depth is investigated using the developed model. The weld bead depth is found to be affected by all the three parameters. Surface and contour plots developed from regression equation are used to optimize the processing parameters for maximizing the weld bead depth. Optimum values of Ip, Ib and HZ are obtained as 259 A, 120 A and 8 Hz respectively. Using this optimum condition, maximum bead depth of the weld is predicted to be 4.325 mm.

  18. Influence of Mn contents in 0Cr18Ni10Ti thin wall stainless steel tube on TIG girth weld quality

    NASA Astrophysics Data System (ADS)

    Liu, Bo

    2017-03-01

    Three kinds of cold worked 0Cr18Ni10Ti thin wall stainless steel tubes with the manganese contents of 1.27%, 1.35% and 1.44% and the cold worked 0Cr18Ni10Ti stainless steel end plug with manganese content of 1.35% were used for TIG girth welding in the present investigation. The effect of different manganese contents in stainless steel tube on weld quality was studied. The results showed that under the same welding conditions, the metallographic performance of the girth weld for the thin wall stainless steel tube with the manganese element content 1.44% welded with end plug was the best. Under the appropriate welding conditions, the quality of the girth weld increased with the increase of the manganese content till 1.44%. It was found that in the case of the Mn content of 1.44%, and under the proper welding condition the welding defects, such as welding cracks were effectively avoided, and the qualified weld penetration can be obtained.. It is concluded that the appropriate increase of the manganese content can significantly improve the TIG girth weld quality of the cold worked 0Cr18Ni10Ti stainless steel tube.

  19. Dilatometric technique for evaluation of the kinetics of solid-state transformation of maraging steel

    SciTech Connect

    Viswanathan, U.K.; Kutty, T.R.G.; Ganguly, C.

    1993-12-01

    Solid-state transformation kinetics of a 350 grad commercial maraging steel were investigated using a nonisothermal dilatometric technique. Two solid-state reactions -- namely, precipitation of intermetallic phases from supersaturated martensite and reversion of martensite to austenite -- were identified. Determination was made of the temperatures at which the rates of these reactions reached a maximum at different heating rates. The kinetics of the individual reactions in terms of activation energy were analyzed by simplified procedures based on the Kissinger equation. An estimated activation energy of 145 {+-} 4 kJ/mol for the precipitation of intermetallic phase was in good agreement with reported results based on the isothermal hardness measurement technique. Martensite to austenite reversion was associated with an activation energy of 224 {+-} 4 kJ/mol, which is very close to the activation energy for diffusion of substitutional elements in ferrite. Results were supplemented with microstructural analysis.

  20. Diffusion bonding of IN 718 to VM 350 grade maraging steel

    NASA Technical Reports Server (NTRS)

    Crosby, S. R.; Biederman, R. R.; Reynolds, C. C.

    1972-01-01

    Diffusion bonding studies have been conducted on IN 718, VM 350 and the dissimilar alloy couple, IN 718 to maraging steel. The experimental processing parameters critical to obtaining consistently good diffusion bonds between IN 718 and VM 350 were determined. Interrelationships between temperature, pressure and surface preparation were explored for short bending intervals under vacuum conditions. Successful joining was achieved for a range of bonding cycle temperatures, pressures and surface preparations. The strength of the weaker parent material was used as a criterion for a successful tensile test of the heat treated bond. Studies of VM-350/VM-350 couples in the as-bonded condition showed a greater yielding and failure outside the bond region.

  1. Pulsed-laser atom probe studies of a precipitation hardened maraging TRIP steel.

    PubMed

    Dmitrieva, O; Choi, P; Gerstl, S S A; Ponge, D; Raabe, D

    2011-05-01

    A precipitation hardened maraging TRIP steel was analyzed using a pulsed laser atom probe. The laser pulse energy was varied from 0.3 to 1.9 nJ to study its effect on the measured chemical compositions and spatial resolution. Compositional analyses using proximity histograms did not show any significant variations in the average matrix and precipitate compositions. The only remarkable change in the atom probe data was a decrease in the ++/+ charge state ratios of the elements. The values of the evaporation field used for the reconstructions exhibit a linear dependence on the laser pulse energy. The adjustment of the evaporation fields used in the reconstructions for different laser pulse energies was based on the correlation of the obtained cluster shapes to the TEM observations. No influence of laser pulse energy on chemical composition of the precipitates and on the chemical sharpness of their interfaces was detected.

  2. Precipitation of aluminum nitride in a high strength maraging steel with low nitrogen content

    SciTech Connect

    Jeanmaire, G.; Dehmas, M.; Redjaïmia, A.; Puech, S.; Fribourg, G.

    2014-12-15

    In the present work, aluminum nitride (AlN) precipitation was investigated in a X23NiCoCrMoAl13-6-3 maraging steel with low nitrogen content (wt.% N = 5.5 ppm). A reliable and robust automatic method by scanning electron microscopy observations coupled with energy dispersive X-ray spectroscopy was developed for the quantification of AlN precipitates. The first stage was to identify the solvus temperature and to develop a heat treatment able to dissolve the AlN precipitates. The experimental determination of equilibrium conditions and solvus temperature show good agreement with ThermoCalc® simulation. Then, from this AlN-free state, the cooling rate, isothermal holding time and temperature were the subject of an intensive investigation in the austenite region of this maraging steel. In spite of the high temperatures used during heat treatments, the growth kinetic of the largest AlN precipitates (> 1 μm) is slow. The cooling rate has a major effect on the size and the number density of AlN due to a higher driving force for nucleation at low temperatures. At last, quenching prior to isothermal annealing at high temperatures leads to fine and dense AlN precipitation, resulting from the martensite to austenite transformation. Experimental results will be discussed and compared with kinetic data obtained with the mobility database MobFe2 implemented in Dictra® software. - Highlights: • Slow dissolution kinetic of AlN precipitates due to both their large size and small chemical driving force • Significant effects of cooling rate prior isothermal heat treatment, holding time and temperature on AlN precipitation • Size of AlN precipitates can be reduced by quenching prior isothermal holding. • Fine precipitation of AlN related to the α → γ transformation.

  3. Use of corrosion-resistant maraging steels in long-lived thread pieces

    NASA Astrophysics Data System (ADS)

    Peskishev, S. A.; Solntsev, Yu. P.; Tsvetkov, A. S.

    2008-02-01

    The effect of isothermal holdings at 350, 500, 580, 660, and 780°C during heating to various sustenitizing temperatures on the grain size, aging processes, structural and mechanical properties, and the stress-strain curves of 03Kh11N10M2T-VD and 03Kh11N8M2F-VD maraging steels with 0.002% B is studied. X-ray diffraction analysis and metallographic examination are performed, and the corrosion and fatigue characteristics of these steels are determined. At the aged state with the maximum strength, the steels exhibit no strain-hardening ability upon tension and retain a high local plastic deformation during necking (ψ ≤ 60%). Preliminary thermal-cycling treatment at 500 800°C causes grain refinement and increases the plastic properties of the steels (the uniform elongation increases to 20%). Isothermal holding during heating to the austenitizing temperature affects an elastoplastic transition at a low tensile strain.

  4. Perforation of HY-100 steel plates with 4340 R{sub c} 38 and T-250 maraging steel rod projectiles

    SciTech Connect

    Forrestal, M.J.; Hanchak, S.J.

    1998-05-25

    The authors conducted perforation experiments with 4340 Rc 38 and T-250 maraging steel, long rod projectiles and HY-100 steel target plates at striking velocities between 80 and 370 m/s. Flat-end rod projectiles with lengths of 89 and 282 mm were machined to nominally 30-mm-diameter so they could be launched from a 30-mm-powder gun without sabots. The target plates were rigidly clamped at a 305-mm-diameter and had nominal thicknesses of 5.3 and 10.5 mm. Four sets of experiments were conducted to show the effects of rod length and plate thickness on the measured ballistic limit and residual velocities. In addition to measuring striking and residual projectile velocities, they obtained framing camera data on the back surfaces of several plates that showed clearly the plate deformation and plug ejection process. They also present a beam model that exhibits qualitatively the experimentally observed mechanisms.

  5. The permeation behavior of deuterium through 1Cr18Ni9Ti stainless steel with TiN+TiC-TiN multiple films

    SciTech Connect

    Xiong, Y.; Song, J.; Luo, D.; Lei, Q.; Chen, C.

    2015-03-15

    The prevention of tritium losses via permeation through structure components is an important issue in fusion technology. The production of thin layers on materials with low diffusivity and/or low surface recombination constants (so-called permeation barriers) seems to be the most practical method to reduce or hinder the permeation of tritium through materials. TiN+TiC+TiN multiple films are deposited on the surface of 1Cr18Ni9Ti stainless steel by ion-beam assisted deposition technology. The characteristics of films are tested by XPS ASEM and XRD, which shows that the film are compact and uniform with a thickness of about 15 μm, and have a good adherence with the substrate below 773 K. The diffraction peaks in the XRD patterns for TiC and TiN are broadened, implying that the multiple films are deposited on the surface of 1Cr18Ni9Ti stainless steel. Meanwhile, the C-H bonded CH{sub 4}-appears in the infrared spectra of multiple films, suggesting that the CH{sub 4}- is in a static state, so hydrogen atom cannot migrate from the site bonded with carbon to a neighboring site. The measured deuterium permeability in 1Cr18Ni9Ti stainless steel coated with multiple films is 2-3 orders of magnitude lower than that of pure 1Cr18Ni9Ti stainless steel substrate from 473 K to 773 K. However, this barrier is partly destroyed above 773 K.

  6. TEM Characterization of a Titanium Nitride (TiN) Inclusion in a Fe-Ni-Co Maraging Steel

    NASA Astrophysics Data System (ADS)

    Descotes, Vincent; Migot, Sylvie; Robaut, Florence; Bellot, Jean-Pierre; Perrin-Guérin, Valérie; Witzke, Sylvain; Jardy, Alain

    2015-07-01

    A TEM observation of a TiN inclusion associated to a spinel (MgAl2O4) and calcium sulfide germs is reported. It shows an orientation relationship between these three phases, indicating an epitaxial growth of the TiN over the spinel and CaS. This observation strengthens the hypothesis of a heterogeneous nucleation of TiN particles during the solidification of a maraging steel.

  7. Structural aspect of the manifestation of thermal brittleness in a maraging steel of the EI-832 type

    NASA Astrophysics Data System (ADS)

    Schastlivtsev, V. M.; Yakovleva, I. L.; Tereshchenko, N. A.; Kruglov, A. A.

    2010-02-01

    The character of fracture, phase composition, and structure of a maraging steel of the EI-832 type in large forged pieces (90 mm and more in cross section) have been investigated. Structural factors responsible for the level of impact toughness of the steel subjected to aging in a forged state and after quenching have been revealed. It has been shown that for this steel the manifestation of thermal brittleness that is caused by precipitation of dispersed titanium carbonitrides at grain boundaries and is not eliminated upon subsequent conventional heat treatment is possible.

  8. Development of a linear pin wear test machine. [304 ss on 3. 50 maraging steel

    SciTech Connect

    Schmale, D.T.; Bourcier, R.J.

    1987-04-01

    In support of a study of the mechanical properties of amorphous alloys produced by laser surface melting, a linear pin wear test machine has been developed and constructed. The machine repeatedly follows a single straight path in one direction through the use of simple kinematic principles. The wear pin is held in a tone arm-like assembly which rides on an off-center rotating bearing. Wear track length can be adjusted by varying bearing eccentricity and tone-arm offset, while wear track location may be changed by specimen translation via two micrometer mounted ball slides. Frictional force is measured by using a load cell mounted on precision bearings while displacement is monitored by using a precalibrated LVDT. The specimen holder is designed to hold irregular specimens up to 0.46 x 1.90 x 2.54 cm. Selected frictional load and displacement data are recorded using a digital oscilloscope. Results of tests performed on an annealed 304 stainless steel specimen using a 350 maraging steel pin are presented.

  9. Aging behavior and mechanical properties of maraging steels in the presence of submicrocrystalline Laves phase particles

    SciTech Connect

    Mahmoudi, A.; Ghavidel, M.R. Zamanzad; Nedjad, S. Hossein; Heidarzadeh, A.; Ahmadabadi, M. Nili

    2011-10-15

    Cold rolling and annealing of homogenized Fe-Ni-Mn-Mo-Ti-Cr maraging steels resulted in the formation of submicrocrystalline Fe{sub 2}(Mo,Ti) Laves phase particles. Optical and scanning electron microscopy, X-ray diffraction, tensile and hardness tests were used to study the microstructure, aging behavior and mechanical properties of the annealed steels. The annealed microstructures showed age hardenability during subsequent isothermal aging at 753 K. Ultrahigh fracture stress but poor tensile ductility was obtained after substantial age hardening in the specimens with 2% and 4% chromium. Increasing chromium addition up to 6% toughened the aged microstructure at the expense of the fracture stress by increasing the volume fraction of retained austenite. The Laves phase particles acted as crack nucleation sites during tensile deformation. - Highlights: {yields} Laves phases dispersed in a BCC iron matrix by annealing of cold rolled samples. {yields} The samples showed age hardenability during subsequent isothermal aging at 753 K. {yields} Ultrahigh fracture stress but poor ductility was obtained after age hardening. {yields} Increasing chromium addition toughened the aged microstructure. {yields} Laves phase particles acting as crack nucleation sites during tensile deformation.

  10. Effects of cold rolling on the microstructure and mechanical properties of Fe-Ni-Mn-Mo-Ti-Cr maraging steels

    NASA Astrophysics Data System (ADS)

    Mahmudi, Abbas; Nedjad, Syamak Hossein; Behnam, Mir Masud Jabbari

    2011-10-01

    Effects of cold rolling on the microstructure and mechanical properties of Fe-Ni-Mn-Mo-Ti-Cr maraging steels were studied. To investigate the microstructure and mechanical properties, optical microscopy, scanning electron microscopy, X-ray diffraction, tensile test, and hardness test were used. The results show that the solution-annealing treatment in the cold-rolled steel redounds to the formation of submicrocrystalline Fe2(Mo, Ti) Laves phase particles, which are stable at high temperatures. These secondary Laves phase particles prevent from recrystallization at high temperatures and correspond to semi-brittle fracture in the subsequent aging treatment.

  11. Atom probe tomography investigation of lath boundary segregation and precipitation in a maraging stainless steel.

    PubMed

    Thuvander, Mattias; Andersson, Marcus; Stiller, Krystyna

    2013-09-01

    Lath boundaries in a maraging stainless steel of composition 13Cr-8Ni-2Mo-2Cu-1Ti-0.7Al-0.3Mn-0.2Si-0.03C (at%) have been investigated using atom probe tomography following aging at 475 °C for up to 100 h. Segregation of Mo, Si and P to the lath boundaries was observed already after 5 min of aging, and the amount of segregation increases with aging time. At lath boundaries also precipitation of η-Ni₃(Ti, Al) and Cu-rich 9R, in contact with each other, takes place. These co-precipitates grow with time and because of coarsening the area number density decreases. After 100 h of aging a ∼5 nm thick film-like precipitation of a Mo-rich phase was observed at the lath boundaries. From the composition of the film it is suggested that the phase in question is the quasicrystalline R' phase. The film is perforated with Cu-rich 9R and η-Ni₃(Ti, Al) co-precipitates. Not all precipitate types present in the matrix do precipitate at the lath boundaries; the Si-containing G phase and γ'-Ni₃(Ti, Al, Si) and the Cr-rich α' phase were not observed at the lath boundaries.

  12. Effect of Cyclic Aging on Mechanical Properties and Microstructure of Maraging Steel 250

    NASA Astrophysics Data System (ADS)

    Tariq, Fawad; Naz, Nausheen; Baloch, Rasheed Ahmed

    2010-10-01

    The effects of thermal cyclic aging on mechanical properties and microstructure of maraging steel 250 were studied using hardness tester, tensile testing machine, impact tester, optical, scanning electron, and stereo microscopy. Samples were solution annealed at 1093 K for 1 h followed by air cooling to form bcc martensite. Cyclic aging treatments were carried out at 753 and 773 K for varying time periods. Increase in hardness and strength with corresponding decrease in ductility and impact strength was observed with increasing aging cycles. Reverted austenite was detected by x-ray diffraction technique formed as a result of cyclic aging. The presence of reverted γ was also confirmed by EDX-SEM analysis and attributed to the formation of Mo- and Ni-rich regions which transformed to γ on cooling. Heterogeneity in composition and amount of reverted γ was found to increase with increase in aging cycles and aging time. Fractography reveals the change in fracture mode from ductile dimple-like to brittle cleavage with increase in hardness and strength due to cyclic aging.

  13. Influence of reverted austenite on the texture and magnetic properties of 350 maraging steel

    NASA Astrophysics Data System (ADS)

    Abreu, Hamilton F. G.; Silva, Jean J.; Silva, Manoel R.; Gomes da Silva, Marcelo J.

    2015-11-01

    The aging temperature to improve magnetic properties in Maraging-350 steel (Mar-350) is limited by the onset of austenite reversion. The traditional process of cooling after aging is to remove the piece from the oven and then to air cool it. The purpose of this research was to characterize the reverted austenite and to investigate the effect of cooling below the martensite start temperature (Ms) on the magnetic properties. The Mar350 samples aged at temperatures above 550 °C, and subsequently cooled in liquid nitrogen presented less austenite than samples cooled in air, resulting in higher magnetization saturation and a lower coercive force. A combination of optical microscopy (OM), X-ray diffraction (XRD) and electron backscatter diffraction (EBSD) techniques were used to characterize the presence of reverted austenite. The crystallographic texture of both martensite and reverted austenite were analyzed. The texture of the reverted austenite coincides with the texture of the parent austenite indicating that a phenomenon of texture memory is present.

  14. Investigation of the plastic fracture of high strength steels

    NASA Technical Reports Server (NTRS)

    Cox, T. B.; Low, J. R., Jr.

    1972-01-01

    An investigation of the plastic fracture process to improve tensile strength in high strength steels is presented. Two generic types of steels are considered: a quenched and tempered grade and a maraging grade, in order to compare two different matrix microstructures. Each type of steel was studied in commercial grade purity and in special melted high purity form, low in residual and impurity elements. The specific alloys dealt with include AISI 4340 and 18 Ni, 200 grade maraging steel, both heat treated to the same yield strength level of approximately 200 ksi.

  15. Investigation of the plastic fracture of high strength steels

    NASA Technical Reports Server (NTRS)

    Cox, T. B.; Low, J. R., Jr.

    1972-01-01

    This investigation deals in detail with the three recognized stages of plastic fracture in high strength steels, namely, void initiation, void growth, and void coalescence. The particular steels under investigation include plates from both commercial purity and high purity heats of AISI 4340 and 18 Ni, 200 grade maraging steels. A scanning electron microscope equipped with an X-ray energy dispersive analyzer, together with observations made using light microscopy, revealed methods of improving the resistance of high strength steels to plastic fracture.

  16. Phase chemistry and precipitation reactions in maraging steels: Part 1. Introduction and study of Co-containing C-300 steel

    SciTech Connect

    Sha, W. ); Cerezo, A.; Smith, G.D.W. )

    1993-06-01

    This article introduces a series of studies of phase transformations in maraging steels. Atom-probe field-ion microscopy (APFIM) was the main research technique employed. Hardness measurements, transmission electron microscopy (TEM), and thermochemical calculations were also used. The composition and morphology of precipitates in the commercial-grade C-300 steel were compared for different aging times at 510[degree]C to investigate the aging sequence. Both Ni[sub 3]Ti and Fe[sub 7]Mo[sub 6] were found to contribute to age hardening. The decomposition starts with the formation of small Mo-enriched Ni[sub 3]Ti particles at very short aging times. The Fe[sub 7]Mo[sub 6] phase forms at a later stage of aging. The matrix concentrations of both Ti and Mo were measured and were found to be low after standard aging conditions. The observation of the Fe[sub 7]Mo[sub 6] [mu] phase is supported by thermochemical calculations, Austenite reversion has been found at the aging temperature, and its composition approaches the predicted equilibrium composition after 8 hours of aging.

  17. Effect of laser-remelting of surface cracks on microstructure and residual stresses in 12Ni maraging steel

    NASA Astrophysics Data System (ADS)

    Grum, J.; Slabe, J. M.

    2006-04-01

    The paper presents the results of a study on possible application of laser-remelting to repair of narrow and comparatively deep cracks at the surface of highly thermo-mechanically loaded parts made of 12% Ni hot-working maraging tool steel. Laser-remelting of maraging steel is, due to very good weldability and flexibility of the process, very prospective for repair of fatigued surfaces of parts made of this steel at which the presence of surface microcracks may be observed. In addition to the efficiency of crack remelting, the influence of laser-remelting on the heat-affected zone in terms of its microstructure and residual stresses was also studied. The microstructure in the laser-remelted track is cellular/dendritic. In the heat-affected zone surrounding the laser-remelted track, the microstructure varies considerably. A microstructure analysis revealed, in the heat-affected zone, five microstructural zones and sub-zones. Residual stresses measured after laser-remelting are with reference to gradual through-depth changing of the stresses favourable.

  18. Precipitation Hardening of Laser-Surfaced Layer of Maraging Alloy at the Surface of Steel 3Kh3M3F

    NASA Astrophysics Data System (ADS)

    Stavrev, D. S.; Shcherbakov, V. S.

    2016-09-01

    The structure and fracture behavior of a layer of maraging alloy deposited by laser surfacing on steel 3Kh3M3F is studied in the initial condition and after precipitation hardening at 550 and 600°C. Microhardness is measured in layer cross sections, and fractures after surfacing and aging are analyzed in an electron microscope.

  19. Elevation of reliability characteristics of maraging steel 03N18K9M5T by creating a "nanotriplex"-type structure

    NASA Astrophysics Data System (ADS)

    Vylezhnev, V. P.; Kokovyakina, S. A.; Simonov, Yu. N.; Sukhikh, A. A.

    2011-03-01

    Characteristics of mechanical strength of maraging steel N18K9M5T after various variants of heat treatment are studied. The treatment mode providing a structure with retained austenite and two types of reverted austenite is determined. An optimum structure ensuring enough strength at high impact toughness and static and cyclic crack resistances is chosen.

  20. Quasi-static compression and tensile stress-strain curves, tantalum - 10% tungsten and 300 grade maraging steel. Final memorandum report

    SciTech Connect

    Benck, R.F.; Silsby, G.F.

    1986-05-01

    The results of quasi-static compression and tension tests of tantalum -10% tungsten alloy and Vascomax 300 CVM 300 trade maraging steel are presented. Young's modulus, Poisson's ratio, and yield strength and ultimate strength were determined at test temperatures of 23.9 C. Results provide engineering properties documentation for materials used in several terminal ballistic tests.

  1. Modeling and Simulation of the Impact Response of Maraging Steel Linear Cellular Alloys for Structural Energetic Material Applications

    NASA Astrophysics Data System (ADS)

    Jakus, Adam; Fredenburg, Anthony; McCoy, Tammy; Cochran, Joe; Thadhani, Naresh

    2009-06-01

    A refined Johnson-Cook material strength model is developed for predicting the dynamic strain and fracture response of Maraging 250 steel at high-strain rates. Finite element simulations of rod-on-anvil impacts are carried out at velocities exceeding 100m/s and compared with experimental impact tests performed on a 7.62mm gas gun. The transient and final dimensions of the simulated and experimentally impacted rods are compared and Johnson-Cook strength parameters are modified accordingly. The newly developed Maraging 250 steel Johnson-cook strength model is then applied to simulate the impact response of multiple, 25% dense linear cellular alloys (LCA) of various geometries at velocities exceeding 100m/s. Analyses of the deformation, fragmentation, and stress transfer behavior of the simulated LCAs are performed and validated through comparison of corresponding impact experiments performed on the LCAs produced via an extrusion and reduction process. Stress transfer to the interior walls varies as a function of LCA geometry, which also influences the outward fragmentation and energy retention at the cross-section of impact.

  2. Measurements of the thermal expansion coefficient of 1Cr18Ni9Ti stainless steel with a laser scanning microdisplacement detection technique

    SciTech Connect

    Fan, H.T.; Shen, C.H.; Liu, Y.; Wang, J. )

    1989-09-01

    A laser scanning microdisplacement detection system has been developed to measure the thermal expansion coefficient of materials over the range from room temperature to 1,200 K. The measurement apparatus consists of a dynamic heating device, a microdisplacement detection system, and a microcomputer-based high-speed data acquisition system. The specimen is dynamically heated from room temperature to 1,200 K by passing a large electrical current through it. The thermal expansion of the specimen is detected by the laser detection system, which records the shift of Fraunhofer diffraction fringes with a photodetector. Measurements of the mean linear thermal expansion coefficient of 1Cr18Ni9Ti stainless steel in the range of 300-1,200 K are described. The results are compared with other reported values of the thermal expansion coefficient. The maximum deviation between them is about 2.3% at the highest temperature, 1,200 K.

  3. Observation of Precipitation Evolution in Fe-Ni-Mn-Ti-Al Maraging Steel by Atom Probe Tomography

    NASA Astrophysics Data System (ADS)

    Pereloma, E. V.; Stohr, R. A.; Miller, M. K.; Ringer, S. P.

    2009-12-01

    We describe the full decomposition sequence in an Fe-Ni-Mn-Ti-Al maraging steel during isothermal annealing at 550 °C. Following significant pre-precipitation clustering reactions within the supersaturated martensitic solid solution, (Ni,Fe)3Ti and (Ni,Fe)3(Al,Mn) precipitates eventually form after isothermal aging for ~60 seconds. The morphology of the (Ni,Fe)3Ti particles changes gradually during aging from predominantly plate-like to rod-like, and, importantly, Mn and Al were observed to segregate to these precipitate/matrix interfaces. The (Ni,Fe)3(Al,Mn) precipitates occurred at two main locations: uniformly within the matrix and at the periphery of the (Ni,Fe)3Ti particles. We relate this latter mode of precipitation to the Mn-Al segregation.

  4. Observation of Precipitation Evolution in Fe-Ni-Mn-Ti-Al Maraging Steel using Atom Probe Tomography

    SciTech Connect

    Pereloma, E. V.; Stohr, R A; Miller, Michael K; Ringer, S. P.

    2009-01-01

    We describe the full decomposition sequence in an Fe-Ni-Mn-Ti-Al maraging steel during isothermal annealing at 550 C. Following significant pre-precipitation clustering reactions within the supersaturated martensitic solid solution, (Ni,Fe){sub 3}Ti and (Ni,Fe){sub 3}(Al,Mn) precipitates eventually form after isothermal aging for {approx}60 seconds. The morphology of the (Ni,Fe){sub 3}Ti particles changes gradually during aging from predominantly plate-like to rod-like, and, importantly, Mn and Al were observed to segregate to these precipitate/matrix interfaces. The (Ni,Fe){sub 3}(Al,Mn) precipitates occurred at two main locations: uniformly within the matrix and at the periphery of the (Ni,Fe){sub 3}Ti particles. We relate this latter mode of precipitation to the Mn-Al segregation.

  5. Corrosion inhibition in 2.0 M sulfuric acid solutions of high strength maraging steel by aminophenyl tetrazole as a corrosion inhibitor

    NASA Astrophysics Data System (ADS)

    Sherif, El-Sayed M.

    2014-02-01

    The corrosion of high strength maraging steel after varied immersion times in concentrated solution, 2.0 M, of sulfuric acid has been investigated. The work was also extended to study the effect of 5-(3-aminophenyl)-tetrazole (APTA) on the inhibition of the steel corrosion. The study has been carried out using electrochemical impedance spectroscopy (EIS), potentiodynamic polarization and scanning electron microscope (SEM) along with energy dispersive X-ray analyzer (EDX) investigations. EIS spectra showed that the corrosion and polarization resistances decrease with increasing the immersion time of the steel before measurement and increase in the presence of APTA and the increase of its concentration. Polarization data agreed with the EIS measurements and indicated that the increase of immersion time increases the corrosion of steel by increasing its corrosion current and corrosion rate and lowering its polarization resistance. On the other hand, the addition of APTA and the increase of its concentration minimized the corrosion of steel through decreasing the corrosion current and corrosion rate and increasing the polarization resistance at all exposure test periods. SEM and EDX investigations confirmed that the inhibition of the maraging steel in the 2.0 M H2SO4 solutions is achieved via the adsorption of the APTA molecules onto the steel protecting its surface from being dissolved easily.

  6. Evolution of Ti-Based Nonmetallic Inclusions During Solution Treatment of Maraging 250 Steel: Thermodynamic Calculations and Experimental Verification

    NASA Astrophysics Data System (ADS)

    Shmulevitsh, Mati; Pinkas, Malki; Weizman, Amir; Frage, Nachum

    2011-06-01

    The evolution of Ti-based nonmetallic inclusions in Maraging 250 steel, namely Ti(CxN1-x) and Ti4C2S2, was investigated experimentally. Their stability in austenite also was analyzed by a thermodynamic analysis of the Fe-Ni-Ti-C-N-S system. It was established that the total concentration of the inclusions decreases from 0.024 pct to 0.008 pct after treatment at 1453 K (1180 °C) for 3 hours. The Ti4C2S2 inclusions completely dissolve in austenite at 1523 K (1250 °C) during 1 hour of treatment. The composition of the carbonitride inclusions is shifted toward higher TiN contents when they dissolve in austenite. Nitrogen-enriched titanium carbonitride inclusions are stable in austenite and their fraction may be reduced only by controlling nitrogen content in the steel. The experimental observations are in good agreement with the results of the thermodynamic analysis.

  7. X-Ray Diffraction Profile Analysis for Characterizing Isothermal Aging Behavior of M250 Grade Maraging Steel

    NASA Astrophysics Data System (ADS)

    Mahadevan, S.; Jayakumar, T.; Rao, B. P. C.; Kumar, Anish; Rajkumar, K. V.; Raj, Baldev

    2008-08-01

    X-ray diffraction (XRD) studies were carried out to characterize aging behavior of M250 grade maraging steel samples subjected to isothermal aging at 755 K for varying durations of 0.25, 1, 3, 10, 40, 70, and 100 hours. Earlier studies had shown typical features of precipitation hardening, wherein the hardness increased to a peak value due to precipitation of intermetallics and decreased upon further aging (overaging) due to reversion of martensite to austenite. Intermetallic precipitates, while coherent, are expected to increase the microstrain in the matrix. Hence, an attempt has been made in the present study to understand the microstructural changes in these samples using XRD line profile analysis. The anisotropic broadening with diffraction angle observed in the simple Williamson Hall (WH) plot has been addressed using the modified WH (mWH) approach, which takes into account the contrast caused by dislocations on line profiles, leading to new scaling factors in the WH plot. The normalized mean square strain and crystallite size estimated from mWH have been used to infer early precipitation and to characterize aging behavior. The normalized mean square strain has been used to determine the Avrami exponent in the Johnson Mehl Avrami (JMA) equation, which deals with the kinetics of precipitation. The Avrami exponent thus determined has matched well with values found by other methods, as reported in literature.

  8. Quasicrystalline and crystalline precipitation during isothermal tempering in a 12Cr-9Ni-4Mo maraging stainless steel

    SciTech Connect

    Liu, P.; Stigenberg, A.H.; Nilsson, J.O.

    1995-07-01

    A thorough microstructural investigation has been performed on a high strength maraging steel of the type 12%Cr-9%Ni-4%Mo-2%Cu-1%Ti. The major precipitate formed during isothermal aging at 475 C is a quasicrystalline phase possessing icosahedral symmetry termed R{prime}-phase with a typical chemical composition of 48%Mo-33%Fe-13%Cr-2%Ni-4%Si. At 550 C the major precipitate is trigonal R-phase with a typical composition of 45%Mo-31%Fe-18%Cr-4%Ni-2%Si. At 550 C also Laves phase with a composition of 48%Mo-35%Fe-13%Cr-2%Ni-2%Si could be observed. At both 475 and 550 C an ordered phase termed L-phase precipitated. This minority phase has an ordered face centered cubic (f.c.c.) structure of type L1{sub 0}. Its composition is typically 9%Fe-4%Cr-52%Ni-15%Mo.-16%Ti-4%Al. R{prime}-phase formed at 475 C transformed to R-phase and Laves phase during aging at 550 C. In an analogous manner, R-phase and Laves phase formed at 550 C transformed to R{prime}-phase during subsequent aging at 475 C. This transformation was rationalized by a strong similarity in crystal structure between quasicrystalline R{prime}-phase of icosahedral symmetry and Frank-Kasper phases such as R-phase and Laves phase.

  9. Corrosion cracking of 03N18K1M3TYu and 02N12Kh5M3 maraging steels in chloride solutions

    SciTech Connect

    Pavlov, V.N.; Chumalo, G.V.; Vereshchagin, A.N.; Melekhov, R.K.

    1987-07-01

    The authors investigate the electrochemical behavior in 0.5% NaCl solution and 42% MgCl/sub 2/ solution and the tendency toward corrosion cracking was determined in boiling 0.5% chloride solution of the cobalt-containing maraging steels in the title. Weld specimens and specimens of the base metal of 03N18K1M3TYu steel were tested in 3% NaCl solution for resistance to corrosion cracking. Additional investigations were made of specimens of that steel with previously created fatigue cracks of the base metal and the weld specimens in 3% NaCl solutions, since that steel is a promising material for structures operating in sea water and low concentration chloride solutions.

  10. Plane strain fracture toughness tests on 2.4 and 3.9-inch-thick maraging steel specimens at various yield strength levels.

    NASA Technical Reports Server (NTRS)

    Fisher, D. M.; Repko, A. J.

    1972-01-01

    Tests of bend and compact specimens were conducted according to ASTM Tentative Method E 399-70T on a 200 grade maraging steel over a range of yield strengths from 123 to 234 ksi. The toughness of any given yield strength level was greater for the overaged condition than for the underaged. Some results which met the specimen size requirements of the method were distinctly lower than corresponding results from larger specimens. Inconsistencies in both validation and invalidation of results by the requirement for linearity of the test record were also noted.

  11. Intermetallic R-phase in maraging steels of the Fe-Cr-Ni-Co-Mo system

    NASA Astrophysics Data System (ADS)

    Tarasenko, L. V.; Titov, V. I.

    2006-07-01

    Concentration and temperature conditions of formation of intermetallic R-phase in margining steels of the Fe-Cr-Ni-Co-Mo system are studied with the help of methods of physicochemical phase analysis and x-ray diffraction analysis. The role of chemical elements in the formation of the multicomponent R-phase is determined. A hypothesis employing the Kasper dimensional principle is suggested for multicomponent intermetallics formed in steels.

  12. Cold brittleness of corrosion-resistant maraging steel 08Kh15N5D2T

    NASA Astrophysics Data System (ADS)

    Makhneva, T. M.

    2012-03-01

    Results of a study of the effect of the method of remelting and of heat treatment modes on the behavior of serial curves of impact toughness and on the position of cold-shortness threshold in steel 08Kh15N5D2T are presented.

  13. Surface modification of superaustenitic and maraging stainless steels by low-temperature gas-phase carburization

    NASA Astrophysics Data System (ADS)

    Gentil, Johannes

    Low-temperature gas-phase carburization of 316L austenitic stainless steel was developed in recent years by the Swagelok company. This process generates great mechanical and electrochemical surface properties. Hardness, wear resistance, fatigue behavior, and corrosion resistance are dramatically improved, while the formation of carbides is effectively suppressed. This new technique is of technical, economical, but especially of scientific interest because the surface properties of common stainless steel can be enhanced to a level of more sophisticated and more expensive superalloys. The consequential continuation of previous research is the application of the carburization process to other steel grades. Differences in chemical composition, microstructure, and passivity between the various alloys may cause technical problems and it is expected that the initial process needs to be optimized for every specific material. This study presents results of low-temperature carburization of AL-6XN (superaustenitic stainless steel) and PH13-8Mo (precipitation-hardened martensitic stainless steel). Both alloys have been treated successfully in terms of creating a hardened surface by introducing high amounts of interstitially dissolved carbon. The surface hardness of AL-6XN was increased to 12GPa and is correlated with a colossal carbon supersaturation at the surface of up to 20 at.%. The hardened case develops a carburization time-dependent thickness between 10mum after one carburization cycle and up to 35mum after four treatments and remains highly ductile. Substantial broadening of X-ray diffraction peaks in low-temperature carburized superaustenitic stainless steels are attributed to the generation of very large compressive biaxial residual stresses. Those large stresses presumably cause relaxations of the surface, so-called undulations. Heavily expanded regions of carburized AL-6XN turn ferromagnetic. Non-carburized AL-6XN is known for its outstanding corrosion resistance

  14. Aging of powder metallurgy N14K7M5T2 maraging steel

    SciTech Connect

    Antsiferov, V.N.; Grevnov, L.M.; Maslenikov, N.N.

    1985-04-01

    The authors study the aging process of sintered N14K7M5T2 marging steel at temperatures of 460-590 C with an isothermal hold of 40 min to 10 h. Electron microscopy was used. The purpose of the investigations was establishment of the type of precipitated phases and their size, form, and kinetics of growth in relation to the aging cycles. An analysis of the electrondiffraction patterns of specimens aged under different conditions made it possible to identify Ni/sub 3/ Ti as the hardening phase.

  15. Effect of annealing on the structure and mechanical properties of the maraging steel N9K17M14-nanoamorphous alloy Co69Fe4Cr4Si12B11 composite material

    NASA Astrophysics Data System (ADS)

    Kolmakov, A. G.; Sevost'yanov, M. A.; Molokanov, V. V.; Zabolotnyi, V. T.; Umnov, P. P.; Umnova, N. V.

    2012-10-01

    The effect of annealing on the structure, mechanical properties, and fracture of a one-dimensional composite material consisting of a microwire made of maraging N9K17M14 steel with a surface layer of a eutectic soft magnetic Co69Fe4Cr4Si12B11 alloy is studied. The optimum temperature of annealing of the composite material is found; as a result, high strength characteristics are achieved at good plasticity. The composite material with a nanoamorphous layer is shown to have the high strength characteristics of the matrix maraging steel at significantly higher plasticity. When the Co69Fe4Cr4Si12B11 alloy is deformed in the composition of the composite material, it exhibits a plasticity effect, and this alloy fails in a brittle manner when deformed in the form of a wire or a ribbon. This effect becomes more pronounced upon annealing.

  16. A Method for Heat Treatment of Maraging Steels 08Kh15N5D2T, 06Kh14N6D2MBT, and 07Kh16N6

    NASA Astrophysics Data System (ADS)

    Il'in, A. A.; Krikushenko, E. S.; Alekseev, V. V.; Silina, V. I.; Belousov, V. V.

    2013-07-01

    A mode for heat treatment of maraging steels 08Kh15N5D2T, 06Kh14N6D2MBT and 07Kh16N6 is developed for critical parts and high-duty structures of "MiG" aircrafts operating under conditions of a complex stress state. The use of the method has made it possible to eliminate rejects and to raise the operational reliability of expensive articles.

  17. Deformation and fracture of a composite material based on a high-strength maraging steel covered with a melt-quenched Co69Fe4Cr4Si12B11 alloy layer

    NASA Astrophysics Data System (ADS)

    Sevost'yanov, M. A.; Kolmakov, A. G.; Molokanov, V. V.; Zabolotnyi, V. T.; Umnov, P. P.; Umnova, N. V.

    2011-04-01

    Multifractal analysis is used to study the deformation and fracture of a promising composite material consisting of a wire base made of K17N9M14 maraging steel covered with a surface layer made from a Co69Fe4Cr4Si12B11 amorphous alloy. As compared to its components, this material has a substantially better set of the mechanical properties.

  18. Gaseous hydrogen embrittlement of high strength steels

    NASA Technical Reports Server (NTRS)

    Gangloff, R. P.; Wei, R. P.

    1977-01-01

    The effects of temperature, hydrogen pressure, stress intensity, and yield strength on the kinetics of gaseous hydrogen assisted crack propagation in 18Ni maraging steels were investigated experimentally. It was found that crack growth rate as a function of stress intensity was characterized by an apparent threshold for crack growth, a stage where the growth rate increased sharply, and a stage where the growth rate was unchanged over a significant range of stress intensity. Cracking proceeded on load application with little or no detectable incubation period. Gaseous hydrogen embrittlement susceptibility increased with increasing yield strength.

  19. Effect of heat-treatment conditions on the structure and physicomechanical and chemical properties of a Ni-Cr-Cu-Ti maraging steel

    NASA Astrophysics Data System (ADS)

    Bannykh, O. A.; Berezovskaya, V. V.

    2007-06-01

    The effects of quenching (from 950°C or from 950 and 850°C) and the aging conditions on the structure, properties, and delayed fracture (DF) of 03Kh11N10M2DT maraging steel has been studied by dilatometry, X-ray diffraction, and fracture tests. The DF-crack growth rate is maximal after aging at 400°C irrespective of the quenching conditions, and the corrosion rate is maximal after aging at 350 400°C in the case of single quenching and at 350°C after double quenching. The kinetics and mechanism of the early stages of the decomposition of a supersaturated α solid solution are investigated by electrical-resistance measurements and transmission electron microscopy. In the state after single quenching, aging occurs in two stages at all isothermal heat treatments; in the state after double quenching, aging occurs in one stage at a time exponent n = 0.2 in the Johnson-Mehl equation. Upon aging at 400°C, the intermediate ordered Fe3(Ni,Ti) phase with a complex cubic lattice precipitates, and the intermetallic compound Ni3Ti precipitates upon subsequent aging. Moreover, copper-rich ɛ-phase precipitates form only in the case of single quenching. The substantial increase in the crack growth rate during DF with n < 0.2 is likely to be caused by the formation of Guinier-Preston zones enriched in nickel and titanium.

  20. Titanium nitride (TiN) precipitation in a maraging steel during the vacuum arc remelting (VAR) process - Inclusions characterization and modeling

    NASA Astrophysics Data System (ADS)

    Descotes, V.; Bellot, J.-P.; Perrin-Guérin, V.; Witzke, S.; Jardy, A.

    2016-07-01

    Titanium Nitride (TiN) inclusions are commonly observed in a Maraging steel containing Nitrogen and Titanium and remelted in a VAR furnace. They can be easily detected by optical microscopy. A nucleus is observed next to a large number of TiN inclusions. A TEM analysis was carried out on a biphasic nucleus composed of a calcium sulfide (CaS) and a spinel (MgAl2O4), surrounded by a TiN particle. An orientation relationship between these three phases was revealed, which suggests a heterogeneous germination of the TiN particle on the nucleus by epitaxial growth. Based on this observation, on thermodynamic considerations and on previous work, a model has been developed and coupled to a numerical simulation of the VAR process to study the formation and evolution of a TiN distribution in the VAR ingot. Microsegregation is modeled using the lever rule, while the kinetics of precipitation is mainly driven by the supersaturation of the liquid bath. This model highlights the influence of the melt rate on the final size of TiN particles.

  1. Space group and atomic structure determination of a nano-sized ordered phase derived from a f c c structure in maraging steel 12Cr-9Ni-4Mo-2Cu using transmission electron microscopy.

    PubMed

    Liu, Ping

    2003-04-01

    The unique properties of maraging steel Sandvik 1RK91 were attributed to unique precipitation: a nano-sized L phase in addition to the quasi-crystalline R' phase, which differs from any precipitation system in conventional maraging steels. The L phase was observed after ageing at either 748 or 823 K. It has flake morphology with dimensions approximately 100 x 500 x 500 A. In the present study the structure of the L phase was examined using convergent-beam electron diffraction (CBED), energy-dispersive X-ray analysis (EDX) and high-resolution electron microscopy (HREM). The L phase could be described as Ti(19)Fe(9)Mo(9)Al(8)Cr(5)Ni(50) or simply M(50)Ni(50) (M = Ti, Fe, Mo, Al and Cr). The L phase is isostructural to FeNi. Its crystal structure was determined to have the ordered structure of the uAu-I type (L1(0), P4/mmm, a = 3.52, c = 3.63 A and Z = 2) with two Ni atoms at (1/2) 0 (1/2) and 0 (1/2) (1/2), and two M atoms at 0 0 0 and (1/2) (1/2) 0. The crystal structure of the L phase can also be described using a primitive tetragonal cell and lattice parameters: a = 2.49 and c = 3.63 A, Z = 1. The Volume of the primitive tetragonal unit cell is 22.5 A(3) and the density is approximately 6.98 g cm(-3). The present study has demonstrated the possibility of determining the structure of an extremely small crystal by utilizing the information from CBED, EDX analysis and HREM.

  2. Steel pressure vessels for hydrostatic pressures to 50 kilobars.

    PubMed

    Lavergne, A; Whalley, E

    1978-07-01

    Cylindrical steel pressure vessels are described that can be used for hydrostatic pressures up to 50 kilobars. Monoblock vessels of 350 maraging steel can be used to 40 kilobars and compound vessels with an inner vessel of 350 maraging steel and an outer vessel of 300 maraging steel to 50 kilobars. Neither requires the cylinder to be end loaded, and so they are much easier to use than the more usual compound vessels with a tungsten carbide inner and steel outer vessel.

  3. Steel, bars, forgings, and tubing 0.80Cr 1.8Ni 0.25Mo (0.38-0.43C) special aircraft quality cleanliness, normalized and tempered. (SAE standard)

    SciTech Connect

    1996-06-01

    This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. These products have been used typically for parts required to meet stringent magnetic particle inspection criteria, having sections 3.5 inches (89 mm) and under in nominal thickness at time of heat treatment, and requiring a through-hardening steel capable of developing a minimum hardness of 30 HRC when properly hardened and tempered and also for parts of greater thickness but requiring proportionately lower hardness, but usage is not limited to such applications. Certain design and processing procedures may cause these products to become susceptible to stress-corrosion cracking after heat treatment; ARP 1110 recommends practices to minimize such conditions. These products are not recommended for use in parts heat treated to a tensile strength range having a maximum over 220 ksi (1517 MPa) or where the high transverse properties of vacuum-arc-remelted or electroslag remelted steel are required. Alloy: 4340 UNS Number: G4340.

  4. Hydrogen trapping in high-strength steels

    SciTech Connect

    Pound, B.G.

    1998-10-09

    Hydrogen trapping in three high-strength steels -- AerMet 100 and AISI 4340 and H11 -- was studied using a potentiostatic pulse technique. Irreversible trapping constants (k) and hydrogen entry fluxes were determined for these alloys in 1 mol/1 acetic acid/1 mol/1 sodium acetate. The order of the k values for the three steels and two 18Ni maraging steels previously studies inversely parallels their threshold stress intensities for stress corrosion cracking (K{sub 1SCC}). Irreversible trapping in AerMet 100 varies with aging temperature and appears to depend on the type of carbide (Fe{sub 3}C or M{sub 2}C) present. For 4340 steel, k can be correlated with K{sub 1SCC} over a range of yield strengths. The change in k is consistent with a change in the principal type of irreversible trap from matrix boundaries to incoherent Fe{sub 3}C. The principal irreversible traps in H11 at high yield strengths are thought to be similar to those in 4340 steel.

  5. Dislocation movement and hysteresis in Maraging blades

    NASA Astrophysics Data System (ADS)

    Di Cintio, Arianna; Marchesoni, Fabio; Ascione, Maria; Bhawal, Abhik; De Salvo, Riccardo

    2009-10-01

    All seismic isolation systems developed for gravitational-wave interferometric detectors, such as LIGO, Virgo and TAMA, make use of Maraging steel blades. The dissipation properties of these blades have been studied at low frequencies, by using a geometric anti-spring (GAS) filter, which allowed the exploration of resonant frequencies below 100 mHz. At this frequency an anomalous transfer function was observed in the GAS filter: this is one of several motivations for this work. The many unexpected effects observed and measured are explainable by the collective movement of dislocations inside the material described with the statistic of self-organised criticality. At low frequencies, below 200 mHz, the dissipation mechanism can subtract elasticity from the system even leading to sudden collapse. While Young's modulus is weaker, excess dissipation is observed. At higher frequencies the applied stress is probably too fast to allow the full growth of dislocation avalanches, and less losses are observed, thus explaining the higher Q-factor in this frequency range. The domino effect that leads to the release of entangled dislocations allows the understanding of the random walk of the Virgo and TAMA inverted pendula, the anomalous GAS filter transfer function as well as the loss of predictability of the ring-down decay in the LIGO seismic attenuation system inverted pendula.

  6. Maraging superalloys and heat treatment processes

    DOEpatents

    Korenko, Michael K.; Gelles, David S.; Thomas, Larry E.

    1986-01-01

    Described herein are nickel-chromium-iron maraging, gamma prime strengthened superalloys containing about 18 to 25 weight percent nickel, about 4 to 8 weight percent chromium, gamma prime forming elements such as aluminum and/or titanium, and a solid solution strengthening element, such as molybdenum. After heat treatment, which includes at least one ausaging treatment and at least one maraging treatment, a microstructure containing gamma prime phase and decomposed Fe-Ni-Cr type martensite is produced.

  7. Creation of composite bronze - maraging steel alloy

    NASA Astrophysics Data System (ADS)

    Potekhin, B. A.; Ilyushin, V. V.; Khristolyubov, A. S.; Zhilyakov, A. Yu.; Ernandes, A.

    2013-09-01

    The possibility is demonstrated of creating alloys based on the system Cu - Fe - Ni - Al, within which the matrix is bronze BrNA 4-1, "reinforced" with dendrites containing, apart from Fe and Cu, about 15% Ni and 1% Al. This dendrite composition provides dispersion hardening. Favorable dendrite morphology provides high deformability of these bronzes, and makes it possible to control mechanical and service properties by heat treatment over a wide range.

  8. The dimensional stability analysis of seventeen stepped specimens of 18Ni 200 grade, PH13-8Mo and A-286

    NASA Technical Reports Server (NTRS)

    Wigley, D. A.

    1983-01-01

    This report documents the results of a dimensional stability analysis of seventeen stepped specimens that were used in the evaluation of factors influencing warpage in metallic alloys being used for cryogenic wind tunnel models. Specimens used in the analysis were manufactured from 18Ni 200 Grade Maaraging steel, PH13-8Mo, and A-286 stainless steel. Quantitative data are provided on the behavior of the specimens due to the effects of both machining and cryogenic cycling effects.

  9. Hydrogen adsorption and diffusion, and subcritical-crack growth in high strength steels and nickel base alloys

    NASA Technical Reports Server (NTRS)

    Wei, R. P.; Klier, K.; Simmons, G. W.; Chornet, E.

    1973-01-01

    Embrittlement, or the enhancement of crack growth by gaseous hydrogen in high strength alloys, is of primary interest in selecting alloys for various components in the space shuttle. Embrittlement is known to occur at hydrogen gas pressures ranging from fractions to several hundred atmospheres, and is most severe in the case of martensitic high strength steels. Kinetic information on subcritical crack growth in gaseous hydrogen is sparse at this time. Corroborative information on hydrogen adsorption and diffusion is inadequate to permit a clear determination of the rate controlling process and possible mechanism in hydrogen enhanced crack growth, and for estimating behavior over a range of temperatures and pressures. Therefore, coordinated studies of the kinetics of crack growth, and adsorption and diffusion of hydrogen, using identical materials, have been initiated. Comparable conditions of temperature and pressure will be used in the chemical and mechanical experiments. Inconel 718 alloy and 18Ni(200) maraging steel have been selected for these studies. Results from these studies are expected to provide not only a better understanding of the gaseous hydrogen embrittlement phenomenon itself, but also fundamental information on hydrogen adsorption and diffusion, and crack growth information that can be used directly for design.

  10. Study of Martensite Ageing with Plasma Ion Nitriding of Steel C300 Using Design of an Experiment

    NASA Astrophysics Data System (ADS)

    Gezicioglu, Yavuz; Inal, Osman Tugay

    2014-09-01

    Double treatment of maraging steel C300 (nitriding + ageing) is studied using experimental design with a full 32 factorial matrix. After this treatment maximum surface hardness is 1270 HV and for the core it is 553 HV.

  11. Microstructural evolution and mechanical properties of an Fe-18Ni-16Cr-4Al base alloy during aging at 950°C

    NASA Astrophysics Data System (ADS)

    Wang, Man; Sun, Yong-duo; Feng, Jing-kai; Zhang, Rui-qian; Tang, Rui; Zhou, Zhang-jian

    2016-03-01

    The development of Gen-IV nuclear systems and ultra-supercritical power plants proposes greater demands on structural materials used for key components. An Fe-18Ni-16Cr-4Al (316-base) alumina-forming austenitic steel was developed in our laboratory. Its microstructural evolution and mechanical properties during aging at 950°C were investigated subsequently. Micro-structural changes were characterized by scanning electron microscopy, electron backscatter diffraction, and transmission electron microscopy. Needle-shaped NiAl particles begin to precipitate in austenite after ageing for 10 h, whereas round NiAl particles in ferrite are coarsened during aging. Precipitates of NiAl with different shapes in different matrices result from differences in lattice misfits. The tensile plasticity increases by 32.4% after aging because of the improvement in the percentage of coincidence site lattice grain boundaries, whereas the tensile strength remains relatively high at approximately 790 MPa.

  12. Extended-time-scale creep measurement on Maraging cantilever blade springs

    NASA Astrophysics Data System (ADS)

    Virdone, Nicole; Agresti, Juri; Bertolini, Alessandro; DeSalvo, Riccardo; Stellacci, Rosalia; Kamp, Justin; Mantovani, Maddalena; Sannibale, Virginio; Tarallo, Marco; Kaltenegger, Lisa

    2008-08-01

    Two controlled temperature facilities were built to induce an accelerated creep rate in a Maraging steel GAS spring and to measure the material's creep over an artificially extended period of time. The data acquisition of the first experiment lasted for almost a year, but then the blades were allowed to creep for six more years before measuring the permanent deformation integrated over time. The data from this first experiment was polluted by a defect in the data acquisition software, but yielded overall creep limits and an evaluation of the Arrhenius acceleration of creep speed with temperature (1.28±0.13 °C -1). The duration of the second experiment was only 1 year but more free of systematic errors. The effective test period of this second experiment (normalized with the Arrhenius acceleration measured in the first experiment) extends in billions of years showing no sign of anomalous creep. The result of both experiments also produced a simple procedure capable of eliminating all practical effects of creep from the Advanced LIGO seismic isolation and suspensions. Measurements of creep under various stress levels, and of the thermal variations of Young's modulus (2.023 (±0.013)×10 -4 °C -1) are reported as well.

  13. Strategies for Mitigation of Hydrogen Environment Assisted Cracking of High Strength Steels

    DTIC Science & Technology

    2006-01-01

    strengthening clusters/coherent precipitates in a complex precipitation hardened, martensitic microstructure. However, the performance of such steels is... martensitic steels such as AISI 4340, this time-dependent subcritical cracking is typically intergranular (IG) along prior- austenite grain boundaries...2,11,13,14,19,36]. For example, l8Ni maraging steels contain only trace levels of P, S, Si, and Mn, but are susceptible to severe IG IHE and HEE [6- 8

  14. Structural factors governing steel resistance during operation in corrosive media under cavitation conditions

    SciTech Connect

    Berezovskaya, V.V.

    1988-05-01

    To evaluate the effect of structural factors on the corrosion resistance of steel under cavitation, a study was made of the effect of cavitation on chromium (95Kh18) and chromium-nickel (12Kh18N9T) corrosion-resistant steels and also on maraging steel 03Kh10N5K5M3KTYuS, specially developed for the loading conditions being studied, together with the austenitic steel 03Kh23N28M3D3T. A study of the effect of martensite content on corrosion and cavitation-corrosion resistance was carried out on steels 12Kh18N9T and 95Kh18 after different treatments. Corrosion tests were conducted in solutions of H/sub 2/SO/sub 4/ and H/sub 3/PO/sub 4/ and scanning electron microscopy was used to assess phase and corrosion behavior. Maraging steels treated for maximum hardness and overaging exhibited high cavitation-corrosion resistance in acid solutions owing to high strength and resistance to microcrack initiation and propagation. It was recommended that under cavitation conditions in corrosive media, high alloy austenitic corrosion-resistant steels are substituted by maraging steels.

  15. Effect of the Aging Temperature of Steel on the Parameters of Fatigue Resistance and Microstrain

    NASA Astrophysics Data System (ADS)

    Myl'nikov, V. V.; Romanov, A. D.; Shetulov, D. I.; Khlybov, A. A.

    2016-07-01

    The interrelation of the parameters of microplastic strain, the slope of the left-hand branch of the fatigue curve, and the fatigue limit of a maraging steel is studied. The growth in the microplastic strain is shown to match the growth in the fatigue limit and the decrease in the slope of the left-hand branch of the fatigue curve. The strength of the steel decreases with decrease in the temperature of post-quenching aging.

  16. An intermetallic forming steel under radiation for nuclear applications

    NASA Astrophysics Data System (ADS)

    Hofer, C.; Stergar, E.; Maloy, S. A.; Wang, Y. Q.; Hosemann, P.

    2015-03-01

    In this work we investigated the formation and stability of intermetallics formed in a maraging steel PH 13-8 Mo under proton radiation up to 2 dpa utilizing nanoindentation, microcompression testing and atom probe tomography. A comprehensive discussion analyzing the findings utilizing rate theory is introduced, comparing the aging process to radiation induced diffusion. New findings of radiation induced segregation of undersize solute atoms (Si) towards the precipitates are considered.

  17. The effect of milling time on the synthesis of Cu54Mg22Ti18Ni6 alloy

    NASA Astrophysics Data System (ADS)

    Kursun, C.; Gogebakan, M.

    2016-03-01

    In the present work, nanocrystalline Cu54Mg22Ti18Ni6 alloy was produced by mechanical alloying from mixtures of pure crystalline Cu, Mg, Ti and Ni powders using a Fritsch planetary ball mill with a ball to powder ratio of 10:1. Morphological changes, microstructural evolution and thermal behaviour of the Cu-Mg-Ti-Ni powders at different stages of milling were characterised by X-ray diffraction (XRD), scanning electron microscopy with energy-dispersive X-ray detection (SEM/EDX) and differential thermal analysis (DTA). This alloy resulted in formation of single phase solid solution with FCC structure α-Cu (Mg, Ti, Ni) after 80 h of milling. In the initial stage of milling different sized and shaped elemental powders became uniform during mechanical alloying. The homogeneity of the Cu54Mg22Ti18Ni6 alloy increased with increasing milling time. The EDX result also confirmed the compositional homogeneity of the powder alloy. The crystallite size of alloy was calculated below 10 nm from XRD data.

  18. Failure Analysis of the Main Rotor Retention Nut from AH-64 Helicopter

    DTIC Science & Technology

    1992-06-01

    Cowmdon of tie HEM Susscepiiliy of ESR 4340 Steel Bob& L Raymond Associates, Newport Beach, CA, Contract DAA629-85-C-0006, Final Report, MTL TR 88-8...metallographic analy- sis of both failed and intact nuts; chemical analysis of the 18 Ni maraging steel C-250 grade steel ; mechanical property, stress...corrosion, and electrochemical tests. The chemi- cal composition of the steel was well within the contractors specification and met the in- dustry standards

  19. Increasing the Cryogenic Toughness of Steels

    NASA Technical Reports Server (NTRS)

    Rush, H. F.

    1986-01-01

    Grain-refining heat treatments increase toughness without substantial strength loss. Five alloys selected for study, all at or near technological limit. Results showed clearly grain sizes of these alloys refined by such heat treatments and grain refinement results in large improvement in toughness without substantial loss in strength. Best improvements seen in HP-9-4-20 Steel, at low-strength end of technological limit, and in Maraging 200, at high-strength end. These alloys, in grain refined condition, considered for model applications in high-Reynolds-number cryogenic wind tunnels.

  20. Stress corrosion cracking of several high strength ferrous and nickel alloys

    NASA Technical Reports Server (NTRS)

    Nelson, E. E.

    1971-01-01

    The stress corrosion cracking resistance of several high strength ferrous and nickel base alloys has been determined in a sodium chloride solution. Results indicate that under these test conditions Multiphase MP35N, Unitemp L605, Inconel 718, Carpenter 20Cb and 20Cb-3 are highly resistant to stress corrosion cracking. AISI 410 and 431 stainless steels, 18 Ni maraging steel (250 grade) and AISI 4130 steel are susceptible to stress corrosion cracking under some conditions.

  1. Erratum: The maraging-steel blades of the Virgo super attenuator

    NASA Astrophysics Data System (ADS)

    Braccini, S.; Casciano, C.; Cordero, F.; Corvace, F.; De Sanctis, M.; Franco, R; Frasconi, F.; Majorana, E.; Paparo, G.; Passaquieti, R.; Rapagnani, P.; Ricci, F.; Righetti, D.; Solina, A.; Valentini, R.

    2004-03-01

    In this article the same symbol cp was used on page 475 for unit volume and for unit mass. This has confused some readers. In equation (17) cp is expressed per unit mass (470 J kg-1 K-1), whereas in the text cp is expressed per unit volume (cp~3.7×106 J m-3 K-1). In terms of cp per unit volume, equation (17) becomes Dth = lambda/cp. The value of Dth remains valid.

  2. Hydrogen embrittlement of a Ti-strengthened 250 grade maraging steel

    SciTech Connect

    Tsay, L.W.; Huang, W.B.; Li, Y.M.; Chen, C.

    1997-04-01

    Constant extension-rate tensile tests are performed to investigate the effects of strain rate and environmental hydrogen concentration on the tensile properties of various aged T-250 specimens. The 426 C (800 F) underaged specimens are very sensitive to strain rate; the 482 C (900 F) peak-aged specimens exhibit a reduced ductility under low strain rates; and the 593 C (1,100 F) overaged specimens are insensitive to strain rate when tested in air. The excellent resistance to embrittlement of the overaged specimens in gaseous hydrogen could be associated with the extensive formation of reverted austenite and the incoherent Ni{sub 3}Ti precipitates. The tensile-fractured surfaces of such specimens reveal a ductile dimple fracture. However, the peak-aged specimens are susceptible to gaseous hydrogen embrittlement, and the embrittled region shows a primary fracture mode of quasi-cleavage. The least resistant to hydrogen embrittlement of the underaged specimens is characterized by a more brittle fracture appearance, that is, intergranular fracture, under a low strain rate or in the gaseous hydrogen environment.

  3. Phase composition and hardening of steels of the Fe-Cr-Ni-Co-Mo system with martensite-austenite structure

    NASA Astrophysics Data System (ADS)

    Tarasenko, L. V.; Shal'kevich, A. B.

    2007-03-01

    The phase composition and mechanical properties of maraging steels of the Fe-Cr-Ni-Co-Mo system are studied as a function of the alloying and of the temperatures of quenching and aging. The intermetallic phases strengthening martensite in different aging stages are determined. The degree of the hardening and the variation of the impact toughness at cryogenic temperatures are compared for steels with different structures (martensite and martensite-austenite) in the stages of maximum hardening and overaging. The effect of retained and reverted austenite on the resistance to crack propagation under impact loading is determined for steels with martensite of a different nature and amount of hardening phases.

  4. Martensitic transformations in high-strength steels at aging

    NASA Astrophysics Data System (ADS)

    Berezovskaya, V. V.; Bannykh, O. A.

    2011-04-01

    The effect of heat treatment and elastic stresses on the texture of maraging NiTi-steels is studied. The interruption of the decomposition of martensite at the early stages is shown to be accompanied by the γ → α transformation, which proceeds upon cooling from the aging temperature and under elastic (σ < σ0.2) tensile stresses. The martensite has a crystallographic texture, which is caused by the evolution of hot-deformation texture as a result of quenching and decomposition of a supersaturated α solid solution.

  5. The question of increasing the contact life of high-strength steels

    SciTech Connect

    Zarotskii, G.I.; Katsov, K.B.; Khrunik, R.A.; Kokotailo, I.V.

    1986-01-01

    Comparative investigations were made of the contact life of 00N18KM5T and 00N14Kh5M3T maraging steels and 38KhN3MFA dispersion-hardened steel with different variations of melting and heat and chemicothermal treatment. The contact life investigations were made in the 450-2000-MPa range of stresses with a degree of slippage of 5%. It was established that regardless of the chemical composition and heat treatment, nitriding by ionized nitrogen in the plasma of a glow discharge provides the greatest increase in specimen contact life (210-245%).

  6. Structural properties of BaFe[subscript 1.8]Ni[subscript 0.2]As[subscript 2] under pressure

    SciTech Connect

    Jia, Feng-Jiang; Yang, Wenge; Li, Lin-Jun; Xu, Zhu-An; Chen, Xiao-Jia

    2014-01-13

    The structural properties of electron-doped compound BaFe1.8Ni0.2As2 are investigated by the synchrotron X-ray powder diffraction at high pressures ranged from 1 bar to 24.0 GPa at room temperature. The compound BaFe1.8Ni0.2As2 holds a tetragonal structure (space group I4/mmm) at ambient condition. Upon compression, the lattice parameter a first monotonically decreases from ambient pressure to 7.0 GPa, then increases till reaching a maximum at 17.8 GPa and again further decreases to the maximum pressure in this investigation. The other lattice parameter c exhibits a slow decrease with increasing pressure before 7.0 GPa and a rapid reduction after that. This anomalous lattice compression results in a lattice collapse at around 12 GPa while the material enters a collapsed tetragonal phase. The Fe-magnetic state change is proposed to account for the structural evolution superconductivity.

  7. Grain-refining heat treatments to improve cryogenic toughness of high-strength steels

    NASA Technical Reports Server (NTRS)

    Rush, H. F.

    1984-01-01

    The development of two high Reynolds number wind tunnels at NASA Langley Research Center which operate at cryogenic temperatures with high dynamic pressures has imposed severe requirements on materials for model construction. Existing commercial high strength steels lack sufficient toughness to permit their safe use at temperatures approaching that of liquid nitrogen (-320 F). Therefore, a program to improve the cryogenic toughness of commercial high strength steels was conducted. Significant improvement in the cryogenic toughness of commercial high strength martensitic and maraging steels was demonstrated through the use of grain refining heat treatments. Charpy impact strength at -320 F was increased by 50 to 180 percent for the various alloys without significant loss in tensile strength. The grain sizes of the 9 percent Ni-Co alloys and 200 grade maraging steels were reduced to 1/10 of the original size or smaller, with the added benefit of improved machinability. This grain refining technique should permit these alloys with ultimate strengths of 220 to 270 ksi to receive consideration for cryogenic service.

  8. Dynamic tensile characterization of Vascomax® maraging C250 and C300 alloys

    DOE PAGES

    Song, Bo; Wakeland, Peter Eric; Furnish, Michael D.

    2015-04-14

    Vascomax® maraging C250 and C300 alloys were dynamically characterized in tension with Kolsky tension bar techniques. Compared with conventional Kolsky tension bar experiments, a pair of lock nuts was used to minimize the pseudo stress peak and a laser system was applied to directly measure the specimen displacement. Dynamic engineering stress–strain curves of the C250 and C300 alloys were obtained in tension at 1000 and 3000 s–1. The dynamic yield strengths for both alloys were similar, but significantly higher than those obtained from quasi-static indentation tests. Both alloys exhibited insignificant strain-rate effect on dynamic yield strength. The C300 alloy showedmore » approximately 10 % higher in yield strength than the C250 alloy at the same strain rates. Necking was observed in both alloys right after yield. The Bridgman correction was applied to calculate the true stress and strain at failure for both alloys. The true failure stress showed a modest strain rate effect for both alloys but no significant difference between the two alloys at the same strain rate. As a result, the C250 alloy was more ductile than the C300 alloy under dynamic loading.« less

  9. Dynamic tensile characterization of Vascomax® maraging C250 and C300 alloys

    SciTech Connect

    Song, Bo; Wakeland, Peter Eric; Furnish, Michael D.

    2015-04-14

    Vascomax® maraging C250 and C300 alloys were dynamically characterized in tension with Kolsky tension bar techniques. Compared with conventional Kolsky tension bar experiments, a pair of lock nuts was used to minimize the pseudo stress peak and a laser system was applied to directly measure the specimen displacement. Dynamic engineering stress–strain curves of the C250 and C300 alloys were obtained in tension at 1000 and 3000 s–1. The dynamic yield strengths for both alloys were similar, but significantly higher than those obtained from quasi-static indentation tests. Both alloys exhibited insignificant strain-rate effect on dynamic yield strength. The C300 alloy showed approximately 10 % higher in yield strength than the C250 alloy at the same strain rates. Necking was observed in both alloys right after yield. The Bridgman correction was applied to calculate the true stress and strain at failure for both alloys. The true failure stress showed a modest strain rate effect for both alloys but no significant difference between the two alloys at the same strain rate. As a result, the C250 alloy was more ductile than the C300 alloy under dynamic loading.

  10. Radiation effects in stainless steel and TiMoN coatings at low-energy helium, krypton and xenon ion impacts

    NASA Astrophysics Data System (ADS)

    Kislitsin, Sergey; Uglov, Vladimir; Larionov, Alexander

    2016-11-01

    The paper reports results of comparative studies of the structure and physical-mechanical properties of stainless Cr18Ni10Ti steel and (TiMo)N coatings irradiated by He, Kr, and Xe ions with an energy of 20 keV/charge. Samples of steel and specimens with TiMoN coating on steel substrates synthesized by vacuum condensation with ion bombardment were irradiated with He, Ks and Xe ions on the low-energy channel of a DC-60 heavy-ion accelerator. It was found that the TiMoN coating significantly exceeds Cr18Ni10Ti stainless steel in the entire range of studied properties, such as strength, corrosion resistance and tendency to blistering.

  11. Heat treatment of investment cast PH 13-8 Mo stainless steel; Part 2: Isothermal aging kinetics

    SciTech Connect

    Robino, C.V.; Cieslak, M.J. . Physical and Joining Metallurgy Dept.); Hochanadel, P.W.; Edwards, G.R. . Dept. of Metallurgical and Materials Engineering)

    1994-04-01

    The hardening response of investment cast PH 13-8 Mo stainless steel has been evaluated by hardness measurements following aging in the temperature range normally specified for this alloy (510 C to 593 C). A new relationship between fraction transformed and hardness was developed, and analysis of the data in terms of the kinetics of precipitation, in a manner similar to that frequently applied to other precipitation-hardenable martensitic steels, yielded low time exponents and a low value for the apparent activation energy. The values of the time exponents were 0.49, 0.37, 0.56, and 0.53 at 510 C, 538 C, 566 C, and 593 C, respectively, and that for the apparent activation energy was 139 kJ/mole. As has been proposed for other maraging type steels, these estimates suggest that [beta]-NiAl precipitates along or near dislocations and that growth of the precipitates is dominated by dislocation pipe diffusion. However, these predictions were neither supported nor refuted by transmission electron microscopy (TEM) because of difficulties in imaging the [beta]-NiAl precipitates at the aging times and temperatures used. Further, analysis of the data using the formalism of Wert and Zener for the growth of precipitates with interfering diffusion fields indicated that the estimates of fraction transformed from hardness data are not fully appropriate for maraging type steels. Consideration of the nature of the Avrami analysis and the electron microscopy results suggests that other phenomena, including dislocation recovery and reversion of martensite to austenite, occur at rates sufficient to convolute the Avrami analysis. It is further suggested that these results cast doubt on the fundamental implications of previous analyses of precipitation kinetics in age-hardening martensitic steels.

  12. Hydrogen induced cracking tests of high strength steels and nickel-iron base alloys using the bolt-loaded specimen

    SciTech Connect

    Vigilante, G.N.; Underwood, J.H.; Crayon, D.; Tauscher, S.; Sage, T.; Troiano, E.

    1997-12-31

    Hydrogen induced cracking tests were conducted on high strength steels and nickel-iron base alloys using the constant displacement bolt-loaded compact specimen. The bolt-loaded specimen was subjected to both acid and electrochemical cell environments in order to produce hydrogen. The materials tested were A723, Maraging 200, PH 13-8 Mo, Alloy 718, Alloy 706, and A286, and ranged in yield strength from 760--1400 MPa. The effects of chemical composition, refinement, heat treatment, and strength on hydrogen induced crack growth rates and thresholds were examined. In general, all high strength steels tested exhibited similar crack growth rates and thresholds were examined. In general, all high strength steels tested exhibited similar crack growth rates and threshold levels. In comparison, the nickel-iron base alloys tested exhibited up to three orders of magnitude lower crack growth rates than the high strength steels tested. It is widely known that high strength steels and nickel base alloys exhibit different crack growth rates, in part, because of their different crystal cell structure. In the high strength steels tested, refinement and heat treatment had some effect on hydrogen induced cracking, though strength was the predominant factor influencing susceptibility to cracking. When the yield strength of one of the high strength steels tested was increased moderately, from 1130 MPa to 1275 MPa, the incubation times decreased by over two orders of magnitude, the crack growth rates increased by an order of magnitude, and the threshold stress intensity was slightly lower.

  13. Effect of hydrogen on internal friction and Young`s modulus of Fe-Cr-Mn austenitic stainless steel

    SciTech Connect

    Usui, Makoto; Asano, Shigeru

    1996-06-01

    The internal friction technique has so far been applied to studies on hydrogen behavior in iron and steel. The hydrogen cold-work peak is well known for pure iron and has also been observed in BCC iron alloys such as ferritic stainless steel and maraging steel. It provides important information about the hydrogen- dislocation interaction in the BCC iron lattice. Meanwhile, for FCC iron alloys such as austenitic stainless steel, another characteristic hydrogen internal friction peak has been found by authors` group and confirmed by several other investigators. In the present study, type 205 austenitic stainless steel (Fe-17Cr-15Mn) was chosen as a nickel-free FCC iron alloy, in which manganese is totally substituted for nickel in type 304 steel. This steel has an unstable FCC lattice as is the case of type 304 steel, in which hydrogen-induced phase transformation depends on the austenite stability. However, the present steel was confirmed to form the {var_epsilon}{sub H} phase after cathodic hydrogen charging in a similar manner to the stable FCC lattice of type 310 steel. In addition, the Fe-Cr-Mn alloy shows a marked anomaly in the temperature dependence of Young`s modulus: an abrupt drop near the Neel temperature T{sub N} and successive lowering below T{sub N}, as has been reported in the literature for some antiferromagnetic materials. The effect of hydrogen on Young`s modulus was studied by several investigators, but there was great inconsistency among their experimental results. The purpose of this paper is to confirm the hydrogen peak of internal friction in type 205 steel and to examine the effect of hydrogen on Young`s modulus of this steel.

  14. Aircraft Steels

    DTIC Science & Technology

    2009-02-19

    NAWCADPAX/TR-2009/ 12 AIRCRAFT STEELS by E. U. Lee R. Taylor C. Lei H. C. Sanders 19 February 2009...MARYLAND NAWCADPAX/TR-2009/ 12 19 February 2009 AIRCRAFT STEELS by E. U. Lee R. Taylor C. Lei H. C. Sanders...Prescribed by ANSI Std. Z39-18 NAWCADPAX/TR-2009/ 12 ii SUMMARY Five high strength and four stainless steels have been studied, identifying their

  15. Phase diffusionless γ↔α transformations and their effect on physical, mechanical and corrosion properties of austenitic stainless steels irradiated with neutrons and charged particles

    NASA Astrophysics Data System (ADS)

    Maksimkin, O. P.

    2016-04-01

    The work presents relationships of γ→α' and α'→γ-transformations in reactor 12Cr18Ni10Ti and 08Cr16Ni11Mo3 austenitic stainless steels induced by cold work, irradiation and/or temperature. Energy and mechanical parameters of nucleation and development of deformation-induced martensitic α'-phase in the non-irradiated and irradiated steels are given. The mechanisms of localized static deformation were investigated and its effect on martensitic γ→α' transformation is determined. It has been shown that irradiation of 12Cr18Ni10Ti steel with heavy Kr ions (1.56MeV/nucleon, fluence of 1·1015 cm-2) results in formation of α'-martensite in near-surface layer of the sample. Results of systematic research on reversed α'→γ-transformation in austenitic metastable stainless steels irradiated with slow (VVR-K) and fast (BN-350) neutrons are presented. The effect of annealing on strength and magnetic characteristics was determined. It was found that at the temperature of 400 °C in the irradiated with neutrons samples (59 dpa) an increase of ferromagnetic α'-phase and microhardness was observed. The obtained results could be used during assessment of operational characteristics of highly irradiated austenitic steels during transportation and storage of Fuel Assemblies for fast nuclear reactors.

  16. A potential means of using acoustic emission for crack detection under cyclic-load conditions.

    NASA Technical Reports Server (NTRS)

    Vary, A.; Klima, S. J.

    1973-01-01

    A preliminary investigation was conducted to assess the feasibility of monitoring acoustic emission signals from fatigue cracks during cyclic bend tests. Plate specimens of 6Al-4V titanium, 2219-T87 aluminum, and 18-Ni maraging steel were tested with and without crack starter notches. It was found that significant acoustic emission signals could be detected in the frequency range from 100 to 400 kHz. Cracks emanating from starter notches were monitored by the ultrasonic pulse-echo technique and periodically measured by micro-optical examination. The investigation indicated that it was possible to extract meaningful acoustic emission signals in a cyclic bend machine environment.

  17. Evaluation of shuttle solid rocket booster case materials. Corrosion and stress corrosion susceptibility of several high temperature materials

    NASA Technical Reports Server (NTRS)

    Pionke, L. J.; Garland, K. C.

    1973-01-01

    Candidate alloys for the Shuttle Solid Rocket Booster (SRB) case were tested under simulated service conditions to define subcritical flaw growth behavior under both sustained and cyclic loading conditions. The materials evaluated were D6AC and 18 Ni maraging steel, both heat treated to a nominal yield strength of 1380 MN/sq m (200 ksi). The sustained load tests were conducted by exposing precracked, stressed specimens of both alloys to alternate immersion in synthetic sea water. It was found that the corrosion and stress corrosion resistance of the 18 Ni maraging steel were superior to that of the D6AC steel under these test conditions. It was also found that austenitizing temperature had little influence on the threshold stress intensity of the D6AC. The cyclic tests were conducted by subjecting precracked surface-flawed specimens of both alloys to repeated load/thermal/environmental profiles which were selected to simulate the SRB missions. It was found that linear removal operations that involve heating to 589 K (600 F) cause a decrease in cyclic life of D6AC steel relative to those tests conducted with no thermal cycling.

  18. Microstructure-fracture toughness relationship of vanadium alloy/stainless steel brazed joints

    NASA Astrophysics Data System (ADS)

    Gan, Y. X.; Aglan, H. A.; Steward, R. V.; Chin, B. A.; Grossbeck, M. L.

    2001-11-01

    In this work, brazing V-5Ti-5Cr to 304 stainless steel (SS 304) using Au-18Ni alloy as filler material was conducted under high vacuum condition. Sessile drop technique was used to determine the wettability of filler alloy to the stainless steel and the vanadium alloy substrates upon which the relationship between the contact angles with time was obtained. Tensile tests were performed on unnotched and notched specimens to demonstrate the overloading behavior and the fracture toughness of the base materials and the brazed joint. Fracture surface was examined for both the V-5Ti-5Cr and the joint to identify the failure mechanisms under static loadings. It was found that the Au-18Ni filler material exhibited good wettability with the SS 304 and V-5Ti-5Cr. The ultimate tensile strength of the brazed joint reached 245 MPa. The strain to failure was about 1.3%. Young's modulus was about 351 GPa. The fracture toughness ( KIc) of this joint was 19.1 MPa √ m. The fracture surface of the joint showed well brazed area with good wettability and proper amount of residual filler material which came from the solidification of residual liquid filler alloy of Au-Ni. The failure of the joint occurred along the interface of the vanadium/filler under static load.

  19. Aluminum diffusion in Al-implanted AISI 321 stainless steel using accelerator-based characterization techniques

    NASA Astrophysics Data System (ADS)

    Noli, F.; Misaelides, P.; Bethge, K.

    1998-04-01

    The aluminum diffusion in near-surface layers of Al-implanted AISI 321 austenitic stainless steel (Fe/Cr18/Ni8/Ti) was studied using ion beam analysis techniques. The implanted samples were investigated at temperatures between 450°C and 650°C (treatment times up to 144 h in vacuum and in air). The Al-profiles were determined by the 992 keV resonance of the 27Al(p,γ) 28Si nuclear reaction as well as by 4He +-Rutherford Backscattering Spectrometry (RBS). The experimental diffusion coefficients, obtained during this study using Fick's second law, were compared with corresponding literature concerning the aluminum diffusion in other relevant metallic materials. The determination of the depth profiles contributes to the interpretation of the high temperature oxidation behavior of Al-implanted stainless steel surfaces.

  20. The thermal fatigue resistance of H-13 Die Steel for aluminum die casting dies

    NASA Technical Reports Server (NTRS)

    1982-01-01

    The effects of welding, five selected surface coatings, and stress relieving on the thermal fatigue resistance of H-13 Die Steel for aluminum die casting dies were studied using eleven thermal fatigue specimens. Stress relieving was conducted after each 5,000 cycle interval at 1050 F for three hours. Four thermal fatigue specimens were welded with H-13 or maraging steel welding rods at ambient and elevated temperatures and subsequently, subjected to different post-weld heat treatments. Crack patterns were examined at 5,000, 10,000, and 15,000 cycles. The thermal fatigue resistance is expressed by two crack parameters which are the average maximum crack and the average cracked area. The results indicate that a significant improvement in thermal fatigue resistance over the control was obtained from the stress-relieving treatment. Small improvements were obtained from the H-13 welded specimens and from a salt bath nitrogen and carbon-surface treatment. The other surface treatments and welded specimens either did not affect or had a detrimental influence on the thermal fatigue properties of the H-13 die steel.

  1. Heat treatment of investment cast PH 13-8 Mo stainless steel: Part II. Isothermal aging kinetics

    NASA Astrophysics Data System (ADS)

    Robino, C. V.; Cieslak, M. J.; Hochanadel, P. W.; Edwards, G. R.

    1994-04-01

    The hardening response of investment cast PH 13-8 Mo stainless steel has been evaluated by hardness measurements following aging in the temperature range normally specified for this alloy (510 °C to 593 °C). A new relationship between fraction transformed and hardness was developed, and analysis of the data in terms of the kinetics of precipitation, in a manner similar to that frequently applied to other precipitation-hardenable martensitic steels, yielded low time exponents and a low value for the apparent activation energy. The values of the time exponents were 0.49, 0.37, 0.56, and 0.53 at 510 °C, 538 °C, 566 °C, and 593 °C, respectively, and that for the apparent activation energy was 139 kJ/mole. As has been proposed for other maraging type steels, these estimates suggest that Β-NiAl precipitates along or near dislocations and that growth of the precipitates is dominated by dislocation pipe diffusion. However, these predictions were neither supported nor refuted by transmission electron microscopy (TEM) because of difficulties in imaging the Β-NiAl precipitates at the aging times and temperatures used. Further, analysis of the data using the formalism of Wert and Zener for the growth of precipitates with interfering diffusion fields indicated that the estimates of fraction transformed from hardness data are not fully appropriate for maraging type steels. Consideration of the nature of the Avrami analysis and the electron microscopy results suggests that other phenomena, including dislocation recovery and reversion of martensite to austenite, occur at rates sufficient to convolute the Avrami analysis. It is further suggested that these results cast doubt on the fundamental implications of previous analyses of precipitation kinetics in age-hardening martensitic steels. Although the Avrami analysis was found not to provide a tenable description of the precipitation kinetics, it does provide a reasonable methodology for portrayal of the hardening response

  2. Response of Split Hopkinson Bar Apparatus Signal to End-Surface Damage, Numerical and Experimental Studies

    DTIC Science & Technology

    2012-01-01

    have a diameter of 14.5 mm, a length of 800 mm and are both made from maraging steel . The sound speed and impedance of the maraging bars were...This constitutive model implies a bilinear stress/strain curve. The bars and striker materials were made from Maraging steel and their mechanical... Steel . Physical Parameters Maraging Steel Density (kg/ m3) 8064 Yield Strength (Pa) 965 106 Elastic Modulus (Pa) 182 109 Poisson’s Ratio 0.3

  3. Influence of free volume and medium-range order on the deformation response of rapidly solidified and bulk Zr-based (Zr52Ti6Al10Cu18Ni14) metallic glass

    NASA Astrophysics Data System (ADS)

    Vishwanadh, B.; Sharma, S. K.; Pujari, P. K.; Kishore, R.; Dey, G. K.; Tewari, R.

    2013-09-01

    Free volume and medium-range order (MRO) present in rapidly solidified ribbons (RSRs) and bulk metallic glasses (BMGs) of Zr52Ti6Al10Cu18Ni14 have been probed by high resolution electron microscopy, fluctuation microscopy, positron annihilation and differential scanning calorimetry. In the as-solidified condition, RSRs showed higher free volume and lower MRO in comparison to BMGs. Within BMGs, the central regions showed higher MRO and lower free volume than the peripheral regions. Uniform deformation of BMGs and RSRs modified their structures, where in, free volume increased in the former and reduced in the latter. These changes in structures led to work hardening in RSRs and work softening in BMGs. Such behaviour could be explained by invoking a concept of critical free volume in the glass phase. For samples (in as-solidified condition) having free volume higher than the critical value, free volume decreased with deformation and showed work-hardening behaviour. In contrast, the work softening behaviour was noticed in samples having free volume lower than the critical free volume.

  4. Lithium-Rich Layered Oxide Li1.18 Ni0.15 Co0.15 Mn0.52 O2 as the Cathode Material for Hybrid Sodium-Ion Batteries.

    PubMed

    Wei, Zhixuan; Gao, Yu; Wang, Lei; Zhang, Chaoyang; Bian, Xiaofei; Fu, Qiang; Wang, Chunzhong; Wei, Yingjin; Du, Fei; Chen, Gang

    2016-08-08

    Li-rich layered oxide Li1.18 Ni0.15 Co0.15 Mn0.52 O2 (LNCM) is, for the first time, examined as the positive electrode for hybrid sodium-ion battery and its Na(+) storage properties are comprehensively studied in terms of galvanostatic charge-discharge curves, cyclic voltammetry and rate capability. LNCM in the proposed sodium-ion battery demonstrates good rate capability whose discharge capacity reaches about 90 mA h g(-1) at 10 C rate and excellent cycle stability with specific capacity of about 105 mA h g(-1) for 200 cycles at 5 C rate. Moreover, ex situ ICP-OES suggests interesting mixed-ions migration processes: In the initial two cycles, only Li(+) can intercalate into the LNCM cathode, whereas both Li(+) and Na(+) work together as the electrochemical cycles increase. Also the structural evolution of LNCM is examined in terms of ex situ XRD pattern at the end of various charge-discharge scans. The strong insight obtained from this study could be beneficial to the design of new layered cathode materials for future rechargeable sodium-ion batteries.

  5. Steel Rattler

    NASA Astrophysics Data System (ADS)

    Trudo, Robert A.; Stotts, Larry G.

    1997-07-01

    Steel Rattler is a multi-phased project to determine the feasibility of using commercial off-the-shelf components in an advanced acoustic/seismic unattended ground sensor. This project is supported by the Defense Intelligence Agency through Sandia National Laboratories as the lead development agency. Steel Rattler uses advanced acoustic and seismic detection algorithms to categorize and identify various heavy vehicles down to the number of cylinders in the engine. This detection is accomplished with the capabilities of new, high-speed digital signal processors which analyze both acoustic and seismic data. The resulting analysis is compared against an onboard library of known vehicles and a statistical match is determined. An integrated thermal imager is also employed to capture digital thermal images for subsequent compression and transmission. Information acquired by Steel Rattler in the field is transmitted in small packets by a built-in low-power satellite communication system. The ground station receivers distribute the coded information to multiple analysis sites where the information is reassembled into coherent messages and images.

  6. Ageing behaviour of an Fe-20Ni-1.8Mn-1.6Ti-0.59Al (wt%) maraging alloy: clustering, precipitation and hardening

    SciTech Connect

    Pereloma, E.V. . E-mail: elena.pereloma@spme.monash.edu.au; Shekhter, A.; Miller, M.K.; Ringer, S.P.

    2004-11-08

    Changes in the solute distribution as well as the evolution of precipitation, microstructure and mechanical properties have been studied in an experimental maraging Fe-20Ni-1.8Mn-1.5Ti-0.59Al (wt%) alloy during ageing at 550 deg C. An initial hardening reaction within 5 s is reported, which is remarkable in terms of extent and rapidity. This strengthening was caused by the formation of complex multi-component atomic co-clusters containing primarily Ni-Ti-Al as well as some Mn. This cluster strengthened condition produced the optimum toughness observed throughout the ageing sequence. After 60 s ageing, the appearance of discrete precipitation of needle-shaped {eta}-Ni{sub 3}Ti particles was associated with a second rise in hardness towards an eventual peak at 600 s. This precipitation hardening was accompanied by an increase in tensile strength and a decrease in ductility. A reverse transformation of martensite to austenite occurs progressively during ageing and this contributes to the initial and secondary softening.

  7. Etude de la migration des interstitiels dans des austenites Fe, Cr (18), Ni (14) pures et industrielles par irradiation dans un microscope a tres haute tension: Role du carbone et du titane

    NASA Astrophysics Data System (ADS)

    Housseau, N.; Pelissier, J.

    1983-12-01

    Nous avons étudié le rôle des impurtés (C ou Ti) dans la condensation et la migration des défauts interstitiels. Les échantillons étudiés sont des aciers austénitiques: (a) acier de synthèse de haute pureté (Cr 18, Ni 14, Fe) avec ou sans carbone; (b) acier industriel avec C (800 ppm) ou Ti (0,45%). Les échantillons ont été irradiés dans un microscope à très haute tension aux doses allant de 10 -4 jusqu'à 10 -1 dpa aux températures de 300°C à 400°C. Dans de telles conditions les défauts observés sont des boucles interstitielles. L'étude de la variation de l'épaisseur de la zone dénudée près du bord de la lame mince en fonction de la température nous a permis d'évaluer l'énergie de migration effective de l'interstitiel dans ces alliages. Dans l'austénite de synthèse carburée ou non sa valeur est de 0.8 eV. Dans l'acier industriel au titane carburé ou non on obtient 2.0 eV. Nous n'avons pas observé d'effet lié au carbone. L'examen de la densité de boucles à saturation dans les divers aciers suggère une forte énergie de liaison interstitiel-titane. Cette énergie de liaison, si l'ont admet que le titane est la seule impureté agissante du système, peut être estimée à 1.2 eV.

  8. Metallic alloy stability studies

    NASA Technical Reports Server (NTRS)

    Firth, G. C.

    1983-01-01

    The dimensional stability of candidate cryogenic wind tunnel model materials was investigated. Flat specimens of candidate materials were fabricated and cryo-cycled to assess relative dimensional stability. Existing 2-dimensional airfoil models as well as models in various stages of manufacture were also cryo-cycled. The tests indicate that 18 Ni maraging steel offers the greatest dimensional stability and that PH 13-8 Mo stainless steel is the most stable of the stainless steels. Dimensional stability is influenced primarily by metallurgical transformations (austenitic to martensitic) and manufacturing-induced stresses. These factors can be minimized by utilization of stable alloys, refinement of existing manufacturing techniques, and incorporation of new manufacturing technologies.

  9. Hot Corrosion Behavior of Stainless Steel with Al-Si/Al-Si-Cr Coating

    NASA Astrophysics Data System (ADS)

    Fu, Guangyan; Wu, Yongzhao; Liu, Qun; Li, Rongguang; Su, Yong

    2017-03-01

    The 1Cr18Ni9Ti stainless steel with Al-Si/Al-Si-Cr coatings is prepared by slurry process and vacuum diffusion, and the hot corrosion behavior of the stainless steel with/without the coatings is studied under the condition of Na2SO4 film at 950 °C in air. Results show that the corrosion kinetics of stainless steel, the stainless steel with Al-Si coating and the stainless steel with Al-Si-Cr coating follow parabolic laws in several segments. After 24 h corrosion, the sequence of the mass gain for the three alloys is the stainless steel with Al-Si-Cr coating < the stainless steel with Al-Si coating < the stainless steel without any coating. The corrosion products of the three alloys are layered. Thereinto, the corrosion products of stainless steel without coating are divided into two layers, where the outside layer contains a composite of Fe2O3 and FeO, and the inner layer is Cr2O3. The corrosion products of the stainless steel with Al-Si coating are also divided into two layers, of which the outside layer mainly consists of Cr2O3, and the inner layer is mainly SiO2. The corrosion film of the stainless steel with Al-Si-Cr coating is thin and dense, which combines well with substrate. Thereinto, the outside layer is mainly Cr2O3, and the inside layer is Al2O3. In the matrix of all of the three alloys, there exist small amount of sulfides. Continuous and protective films of Cr2O3, SiO2 and Al2O3 form on the surface of the stainless steel with Al-Si and Al-Si-Cr coatings, which prevent further oxidation or sulfide corrosion of matrix metals, and this is the main reason for the much smaller mass gain of the two alloys than that of the stainless steel without any coatings in the 24 h hot corrosion process.

  10. Study of the plasma immersion implantation of titanium in stainless steel

    NASA Astrophysics Data System (ADS)

    Nikitenkov, N. N.; Sutygina, A. N.; Shulepov, I. A.; Sivin, D. O.; Kashkarov, E. B.

    2015-04-01

    The results of the study of the pulsed plasma-immersion ion implantation of titanium in steel Cr18Ni10Ti depending on the time (dose) implantation are presented. It is shown that the change of the element and the phase composition of the surface layers and their microscopic characteristics and mechanical properties (hardness, wear resistance) depending on the implantation time is not monotonic, but follows to a certain rule. The possibility of interpretation of the obtained results in the thermal spike concept of the generation on the surface by the stable (magic) clusters is discussed. This concept follows logically from the recent studies on the plasma arc composition and from a polyatomic clusters-surface interaction.

  11. Supertough Stainless Bearing Steel

    NASA Technical Reports Server (NTRS)

    Olson, Gregory B.

    1995-01-01

    Composition and processing of supertough stainless bearing steel designed with help of computer-aided thermodynamic modeling. Fracture toughness and hardness of steel exceeds those of other bearing steels like 440C stainless bearing steel. Developed for service in fuel and oxidizer turbopumps on Space Shuttle main engine. Because of strength and toughness, also proves useful in other applications like gears and surgical knives.

  12. EVALUATION OF ARMCO PH13-8Mo,

    DTIC Science & Technology

    STAINLESS STEEL, PHYSICAL PROPERTIES ), (*MARAGING STEELS, PHYSICAL PROPERTIES ), DISPERSION HARDENING, HEAT TREATMENT, TENSILE PROPERTIES , FRACTURE(MECHANICS), STRESS CORROSION, FATIGUE(MECHANICS), TOUGHNESS

  13. Ultrahigh carbon steels, Damascus steels, and superplasticity

    SciTech Connect

    Sherby, O.D.; Wadsworth, J.

    1997-04-01

    The processing properties of ultrahigh carbon steels (UHCSs) have been studied at Stanford University over the past twenty years. These studies have shown that such steels (1 to 2.1% C) can be made superplastic at elevated temperature and can have remarkable mechanical properties at room temperature. It was the investigation of these UHCSs that eventually brought us to study the myths, magic, and metallurgy of ancient Damascus steels, which in fact, were also ultrahigh carbon steels. These steels were made in India as castings, known as wootz, possibly as far back as the time of Alexander the Great. The best swords are believed to have been forged in Persia from Indian wootz. This paper centers on recent work on superplastic UHCSs and on their relation to Damascus steels. 32 refs., 6 figs.

  14. [Determination of minor elements in stainless steel by laser-induced plasma spectroscopy (LIPS)].

    PubMed

    Li, Jing; Zhai, Chao; Zhang, Shi-Ding; Zhang, Jian-Qiu; Meng, Xiang-Ru

    2008-04-01

    Laser-induced plasma spectroscopy (LIPS) is characterized by its non-contact and real-time analysis. Its application to the determination of steel composition can meet the need of high-speed, continuous and automatic production in large steel companies. In the present article the minor elements concentrations of aluminum, manganese, cobalt, molybdenum, and titanium in a series of stainless steel 1Cr18Ni9Ti samples were determinate by laser-induced plasma spectroscopy, based on a Nd : YAG Q-switched solid laser with wavelength 1 064 nm as an exciting source and ICCD as detector. In the experiment the working delay time and gate time of ICCD were set suitably to get high signal-to-noise ratio emission spectral lines, and the internal standardization method related to matrix effect was used to deal with spectral data. Experiment results show that the concentration ratios of all the measured elements versus the reference element ferrum have a good linear relationship with the intensity ratios of them, the detection limits of the five tested elements are within 150 microg x g(-1).

  15. Welding Rustproof Steels

    NASA Technical Reports Server (NTRS)

    Hoffmann, W

    1929-01-01

    The following experimental results will perhaps increase the knowledge of the process of welding rustproof steels. The experiments were made with two chrome-steel sheets and with two chrome-steel-nickel sheets having the composition shown in Table I.

  16. Comminuting irradiated ferritic steel

    DOEpatents

    Bauer, Roger E.; Straalsund, Jerry L.; Chin, Bryan A.

    1985-01-01

    Disclosed is a method of comminuting irradiated ferritic steel by placing the steel in a solution of a compound selected from the group consisting of sulfamic acid, bisulfate, and mixtures thereof. The ferritic steel is used as cladding on nuclear fuel rods or other irradiated components.

  17. The steel scrap age.

    PubMed

    Pauliuk, Stefan; Milford, Rachel L; Müller, Daniel B; Allwood, Julian M

    2013-04-02

    Steel production accounts for 25% of industrial carbon emissions. Long-term forecasts of steel demand and scrap supply are needed to develop strategies for how the steel industry could respond to industrialization and urbanization in the developing world while simultaneously reducing its environmental impact, and in particular, its carbon footprint. We developed a dynamic stock model to estimate future final demand for steel and the available scrap for 10 world regions. Based on evidence from developed countries, we assumed that per capita in-use stocks will saturate eventually. We determined the response of the entire steel cycle to stock saturation, in particular the future split between primary and secondary steel production. During the 21st century, steel demand may peak in the developed world, China, the Middle East, Latin America, and India. As China completes its industrialization, global primary steel production may peak between 2020 and 2030 and decline thereafter. We developed a capacity model to show how extensive trade of finished steel could prolong the lifetime of the Chinese steelmaking assets. Secondary steel production will more than double by 2050, and it may surpass primary production between 2050 and 2060: the late 21st century can become the steel scrap age.

  18. Methods of forming steel

    DOEpatents

    Branagan, Daniel J.; Burch, Joseph V.

    2001-01-01

    In one aspect, the invention encompasses a method of forming a steel. A metallic glass is formed and at least a portion of the glass is converted to a crystalline steel material having a nanocrystalline scale grain size. In another aspect, the invention encompasses another method of forming a steel. A molten alloy is formed and cooled the alloy at a rate which forms a metallic glass. The metallic glass is devitrified to convert the glass to a crystalline steel material having a nanocrystalline scale grain size. In yet another aspect, the invention encompasses another method of forming a steel. A first metallic glass steel substrate is provided, and a molten alloy is formed over the first metallic glass steel substrate to heat and devitrify at least some of the underlying metallic glass of the substrate.

  19. Welding irradiated stainless steel

    SciTech Connect

    Kanne, W.R. Jr.; Chandler, G.T.; Nelson, D.Z.; Franco-Ferreira, E.A.

    1993-12-31

    Conventional welding processes produced severe underbead cracking in irradiated stainless steel containing 1 to 33 appm helium from n,a reactions. A shallow penetration overlay technique was successfully demonstrated for welding irradiated stainless steel. The technique was applied to irradiated 304 stainless steel that contained 10 appm helium. Surface cracking, present in conventional welds made on the same steel at the same and lower helium concentrations, was eliminated. Underbead cracking was minimal compared to conventional welding methods. However, cracking in the irradiated material was greater than in tritium charged and aged material at the same helium concentrations. The overlay technique provides a potential method for repair or modification of irradiated reactor materials.

  20. X-Ray Diffraction Study on the Strain Anisotropy and Dislocation Structure of Deformed Lath Martensite

    NASA Astrophysics Data System (ADS)

    Hossein Nedjad, S.; Hosseini Nasab, F.; Movaghar Garabagh, M. R.; Damadi, S. R.; Nili Ahmadabadi, M.

    2011-08-01

    18Ni (300) maraging steel possessing lath martensite structure was deformed by four passes of equal-channel angular pressing (ECAP) at ambient temperature. Line profile analysis (LPA) of X-ray diffraction (XRD) patterns identified strong strain anisotropy and remarkable increases in the relative fraction of screw dislocations after ECAP. The strain anisotropy was reasonably accounted for by the anisotropy of elastic constants. Domination of screw dislocations in the deformed structure was attributed to the preferred annihilation of edge dislocations in the early stages of deformation along with the difficulties for annihilation of screw dislocations by cross slipping. Cobalt addition was mainly assumed to make cross slipping difficult by reducing stacking-fault energy and favoring short-range ordering.

  1. A potential means of using acoustic emission for crack detection under cyclic-load conditions

    NASA Technical Reports Server (NTRS)

    Vary, A.; Klima, S. J.

    1973-01-01

    A preliminary investigation was conducted to assess the feasibility of monitoring acoustic emission signals from fatigue cracks during cyclic bend tests. Plate specimens of 6A1-4V titanium, 2219-T87 aluminum, and 18-Ni maraging steel were tested with and without crack starter notches. It was found that significant acoustic emission signals could be detected in the frequency range from 100 kHz to 400 kHz. Cracks emanating from starter notches were monitored by the ultrasonic pulse-echo technique and periodically measured by micro-optical examination. Methods used to reduce the effects of extraneous noises (i.e., machine noises, fretting) are described. A frequency spectrum analyzer was used to characterize the emissions and to evaluate methods used to acquire the signals (i.e., transducer location, bandwidth selection). The investigation indicated that it was possible to extract meaningful acoustic emission signals in a cyclic bend machine environment.

  2. Lightweight Multifunctional Linear Cellular Alloy Ballistic Structures

    DTIC Science & Technology

    2006-04-26

    for densification. For this program, square cell LCA honeycomb with both maraging steel and super invar compositions were fabricated using SAI’s...provide high levels of energy absorption; 5 to 7 times that of that of conventional materials. Maraging steel honeycomb structure having a density of 2.1 g...cm3 and yield strength ~650 MPa, has been shown to absorb ~180 MJ/m3. Figure 2 shows stress train curves for maraging steel under quasistatic and

  3. Coated 4340 Steel

    DTIC Science & Technology

    2013-08-26

    the effects of three coating systems on the mechanical property, fatigue, and...defined striations or striations-like features were formed in air, Figure A-13(b). On the other hand, intergranular cracking and formation of brittle...steel, in air. Their respective effects on the fatigue resistance of bare 4340 steel were similar in both of the employed environments, air and

  4. Steel Industry Wastes.

    ERIC Educational Resources Information Center

    Schmidtke, N. W.; Averill, D. W.

    1978-01-01

    Presents a literature review of wastes from steel industry, covering publications of 1976-77. This review covers: (1) coke production; (2) iron and steel production; (3) rolling operations; and (4) surface treatment. A list of 133 references is also presented. (NM)

  5. EAST ELEVATION, LTV STEEL (FORMERLY REPUBLIC STEEL), 8" BAR MILL, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    EAST ELEVATION, LTV STEEL (FORMERLY REPUBLIC STEEL), 8" BAR MILL, BUFFALO PLANT. VIEW LOOKING SOUTHWEST FROM ROLL SHOP. 8" BAR MILL DESIGNED AND BUILT BY DONNER STEEL CO. (PREDECESSOR OF REPUBLIC), 1919-1920. FOR DESCRIPTION OF ORIGINAL MILL SEE "IRON AGE", 116\\4 (23 JULY 1925): 201-204. - LTV Steel, 8-inch Bar Mill, Buffalo Plant, Buffalo, Erie County, NY

  6. Damascus steel ledeburite class

    NASA Astrophysics Data System (ADS)

    Sukhanov, D. A.; Arkhangelsky, L. B.; Plotnikova, N. V.

    2017-02-01

    Discovered that some of blades Damascus steel has an unusual nature of origin of the excess cementite, which different from the redundant phases of secondary cementite, cementite of ledeburite and primary cementite in iron-carbon alloys. It is revealed that the morphological features of separate particles of cementite in Damascus steels lies in the abnormal size of excess carbides having the shape of irregular prisms. Considered three hypotheses for the formation of excess cementite in the form of faceted prismatic of excess carbides. The first hypothesis is based on thermal fission of cementite of a few isolated grains. The second hypothesis is based on the process of fragmentation cementite during deformation to the separate the pieces. The third hypothesis is based on the transformation of metastable cementite in the stable of angular eutectic carbide. It is shown that the angular carbides are formed within the original metastable colony ledeburite, so they are called “eutectic carbide”. It is established that high-purity white cast iron is converted into of Damascus steel during isothermal soaking at the annealing. It was revealed that some of blades Damascus steel ledeburite class do not contain in its microstructure of crushed ledeburite. It is shown that the pattern of carbide heterogeneity of Damascus steel consists entirely of angular eutectic carbides. Believe that Damascus steel refers to non-heat-resistant steel of ledeburite class, which have similar structural characteristics with semi-heat-resistant die steel or heat-resistant high speed steel, differing from them only in the nature of excess carbide phase.

  7. Structural Amorphous Steels

    NASA Astrophysics Data System (ADS)

    Lu, Z. P.; Liu, C. T.; Thompson, J. R.; Porter, W. D.

    2004-06-01

    Recent advancement in bulk metallic glasses, whose properties are usually superior to their crystalline counterparts, has stimulated great interest in fabricating bulk amorphous steels. While a great deal of effort has been devoted to this field, the fabrication of structural amorphous steels with large cross sections has remained an alchemist’s dream because of the limited glass-forming ability (GFA) of these materials. Here we report the discovery of structural amorphous steels that can be cast into glasses with large cross-section sizes using conventional drop-casting methods. These new steels showed interesting physical, magnetic, and mechanical properties, along with high thermal stability. The underlying mechanisms for the superior GFA of these materials are discussed.

  8. Glass Stronger than Steel

    DOE R&D Accomplishments Database

    Yarris, Lynn

    2011-03-28

    A new type of damage-tolerant metallic glass, demonstrating a strength and toughness beyond that of steel or any other known material, has been developed and tested by a collaboration of researchers from Berkeley Lab and Caltech.

  9. Joining Steel Armor - Intermix

    DTIC Science & Technology

    1979-03-01

    TARADCOM a d ki Lk A el B~ 0el RWET0 TECHNICAL REPORT NO. 12311 JOINING STEEL ARMOR - INTERMIX March 1979 U U * S* ’ "U .by B. . A.SCEV * U...authorized documents. O "if TECHNICAL REPORT NO. 12311 JOINING STEEL ARMOR - INTERMIX BY B. A. SCHEVO March 1979 AMS: 3197..6D.4329 TARADCOM ARMOR AND...Intermix Process ...... ........ 3 Test Procedures - Intermix Armor ........ ......... 4 Mock Hull ................. ..................... 5 Results

  10. Life after Steel

    ERIC Educational Resources Information Center

    Mangan, Katherine

    2013-01-01

    Bobby Curran grew up in a working-class neighborhood in Baltimore, finished high school, and followed his grandfather's steel-toed bootprints straight to Sparrows Point, a 3,000-acre sprawl of industry on the Chesapeake Bay. College was not part of the plan. A gritty but well-paying job at the RG Steel plant was Mr. Curran's ticket to a secure…

  11. Ferrium M54 Steel

    DTIC Science & Technology

    2015-03-18

    15 to 18% (reference 1). Beyond this range the alloy becomes more noble than steel and loses its sacrificial protection property . Therefore, Zn-14...for a 7075-T651 aluminum alloy , which was subjected to biaxial fatigue loading in 3.5% NaCl solution (reference 27). NAWCADPAX/TIM-2014/292...Edition, Properties and Selection: Iron, Steels, and High- Performance Alloys , ASM International, 1990, p. 395. 8. G. L. Spencer and D. J. Duquette

  12. Articles comprising ferritic stainless steels

    SciTech Connect

    Rakowski, James M.

    2016-06-28

    An article of manufacture comprises a ferritic stainless steel that includes a near-surface region depleted of silicon relative to a remainder of the ferritic stainless steel. The article has a reduced tendency to form an electrically resistive silica layer including silicon derived from the steel when the article is subjected to high temperature oxidizing conditions. The ferritic stainless steel is selected from the group comprising AISI Type 430 stainless steel, AISI Type 439 stainless steel, AISI Type 441 stainless steel, AISI Type 444 stainless steel, and E-BRITE.RTM. alloy, also known as UNS 44627 stainless steel. In certain embodiments, the article of manufacture is a fuel cell interconnect for a solid oxide fuel cell.

  13. Joining of zirconia ceramic to stainless steel and to itself using Ag{sub 57}Cu{sub 38}Ti{sub 5} filler metal

    SciTech Connect

    Hao, H.; Wang, Y.; Jin, Z.; Wang, X.

    1995-08-01

    The brazing of ZrO{sub 2} ceramic to 1Cr18Ni9Ti stainless steel and to itself was performed using Ag{sub 57}Cu{sub 38}Ti{sub 5} filler metal under a vacuum of t {times} 10{sup {minus}3} Pa. The effects o9f interlayer copper on the ceramic to stainless steel joint strength, and the brazing temperature (1,073 to 1,323 K) and holding time (0 to 60 min) on ceramic to ceramic joint strength were investigated. The joint strength was evaluated by shear testing. An interfacial reaction layer between the ceramic and the filler metal was found, and the reaction products were {delta}-TiO and {gamma}-AgTi{sub 3}. The joint strength of ZrO{sub 2} ceramic to stainless steel was improved by using a layer of copper of a suitable thickness. The brazing temperature and holding time had a strong influence on the joint strength of ceramic time had a strong influence on the joint strength of ceramic to ceramic, and the joint strength was mainly controlled by reaction layer thickness and the properties of the reaction products. The maximum shear strength was obtained for brazing at 1,123 K for 30 min and an interfacial reaction layer thickness of {approximately}4.4 {micro}m.

  14. View northwest, wharf A, sheet steel bulkhead, steel lift tower ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View northwest, wharf A, sheet steel bulkhead, steel lift tower - U.S. Coast Guard Sandy Hook Station, Western Docking Structure, West of intersection of Canfield Road & Hartshorne Drive, Highlands, Monmouth County, NJ

  15. Superclean steel development

    SciTech Connect

    Richman, R.H.; McNaughton, W.P. )

    1989-12-01

    The Electric Power Research Institute has actively encouraged and sponsored a number of research projects to develop a superclean 3.5NiCrMoV steel for low pressure turbine rotors. Such steel is highly resistant to temper embrittlement and will thus facilitate increased efficiency in electricity generation through the use of higher operating temperatures and improvements in design. The objective of this interim report was to integrate the results that have been generated to date worldwide in the pursuit of superclean steel. The report contains detailed findings that enable the interested utility to evaluate how the results affect utility decision making. A companion document has been written to summarize the findings from this technical report. The results indicate that steels with impurity contents typical of the superclean specification can be manufactured for production rotors with properties that equal or exceed those for conventional 3.5NiCrMoV rotors in every detail. Of particular interest are the results that the superclean steels appear to be virtually resistant to temper embrittlement to a temperature of 500 {degrees}C. 109 refs., 51 figs., 9 tabs.

  16. Trends in steel technology. [Dual phase and HSLA steels

    SciTech Connect

    Not Available

    1980-01-01

    Dual phase steels, composite products, and microalloyed steels are making inroads in the automotive industry applications for bumpers, automotive parts, bodies, mechanical parts, suspension and steering equipment and truck bumpers. New steels are also used to support solar mirrors and cells, in corrosive environments in the oil and gas industry, fusion reactors, and pressure vessels in nuclear power plants. (FS)

  17. Continuous steel production and apparatus

    DOEpatents

    Peaslee, Kent D.; Peter, Jorg J.; Robertson, David G. C.; Thomas, Brian G.; Zhang, Lifeng

    2009-11-17

    A process for continuous refining of steel via multiple distinct reaction vessels for melting, oxidation, reduction, and refining for delivery of steel continuously to, for example, a tundish of a continuous caster system, and associated apparatus.

  18. Stainless steel tanks

    SciTech Connect

    Hagen, T.

    1995-12-31

    There is currently no recognized code or standard for the design, fabrication and construction of atmospheric and low pressure stainless steel tanks. At the present time these tanks are being designed to individual specifications, manufacturers standards or utilizing other codes and standards that may not be entirely applicable. Recognizing the need, the American Petroleum Institute will be publishing a new appendix to the API STD 650 Standard which will cover stainless steel tanks. The new Appendix was put together by a Task Group of selected individuals from the API Subcommittee of Pressure Vessels and Tanks from the Committee on Refinery Equipment. This paper deals with the development and basis of the new appendix. The new appendix will provide a much needed standard to cover the material, design, fabrication, erection and testing requirements for vertical, cylindrical, austenitic stainless steel aboveground tanks in nonrefrigerated service.

  19. A-3 steel work completed

    NASA Technical Reports Server (NTRS)

    2009-01-01

    Stennis Space Center engineers celebrated a key milestone in construction of the A-3 Test Stand on April 9 - completion of structural steel work. Workers with Lafayette (La.) Steel Erector Inc. placed the last structural steel beam atop the stand during a noon ceremony attended by more than 100 workers and guests.

  20. Microbial-Influenced Corrosion of Corten Steel Compared with Carbon Steel and Stainless Steel in Oily Wastewater by Pseudomonas aeruginosa

    NASA Astrophysics Data System (ADS)

    Mansouri, Hamidreza; Alavi, Seyed Abolhasan; Fotovat, Meysam

    2015-07-01

    The microbial corrosion behavior of three important steels (carbon steel, stainless steel, and Corten steel) was investigated in semi petroleum medium. This work was done in modified nutrient broth (2 g nutrient broth in 1 L oily wastewater) in the presence of Pseudomonas aeruginosa and mixed culture (as a biotic media) and an abiotic medium for 2 weeks. The behavior of corrosion was analyzed by spectrophotometric and electrochemical methods and at the end was confirmed by scanning electron microscopy. The results show that the degree of corrosion of Corten steel in mixed culture, unlike carbon steel and stainless steel, is less than P. aeruginosa inoculated medium because some bacteria affect Corten steel less than other steels. According to the experiments, carbon steel had less resistance than Corten steel and stainless steel. Furthermore, biofilm inhibits separated particles of those steels to spread to the medium; in other words, particles get trapped between biofilm and steel.

  1. Braze alloy spreading on steel

    NASA Technical Reports Server (NTRS)

    Siewert, T. A.; Heine, R. W.; Lagally, M. G.

    1978-01-01

    Scanning electron microscopy (SEM) and Auger electron microscopy (AEM) were employed to observe elemental surface decomposition resulting from the brazing of a copper-treated steel. Two types of steel were used for the study, stainless steel (treated with a eutectic silver-copper alloy), and low-carbon steel (treated with pure copper). Attention is given to oxygen partial pressure during the processes; a low enough pressure (8 x 10 to the -5th torr) was found to totally inhibit the spreading of the filler material at a fixed heating cycle. With both types of steel, copper treatment enhanced even spreading at a decreased temperature.

  2. 77 FR 30589 - SteelRiver Infrastructure Partners LP, SteelRiver Infrastructure Associates LLC, SteelRiver...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-05-23

    ... Surface Transportation Board SteelRiver Infrastructure Partners LP, SteelRiver Infrastructure Associates LLC, SteelRiver Infrastructure Fund North America LP, and Patriot Funding LLC--Control Exemption--Patriot Rail Corp., et al. SteelRiver Infrastructure Partners LP (SRIP LP), SteelRiver...

  3. Ferritic steel melt and FLiBe/steel experiment : melting ferritic steel.

    SciTech Connect

    Troncosa, Kenneth P.; Smith, Brandon M.; Tanaka, Tina Joan

    2004-11-01

    In preparation for developing a Z-pinch IFE power plant, the interaction of ferritic steel with the coolant, FLiBe, must be explored. Sandia National Laboratories Fusion Technology Department was asked to drop molten ferritic steel and FLiBe in a vacuum system and determine the gas byproducts and ability to recycle the steel. We tried various methods of resistive heating of ferritic steel using available power supplies and easily obtained heaters. Although we could melt the steel, we could not cause a drop to fall. This report describes the various experiments that were performed and includes some suggestions and materials needed to be successful. Although the steel was easily melted, it was not possible to drip the molten steel into a FLiBe pool Levitation melting of the drop is likely to be more successful.

  4. History of ultrahigh carbon steels

    SciTech Connect

    Wadsworth, J.; Sherby, O.D.

    1997-06-20

    The history and development of ultrahigh carbon steels (i.e., steels containing between 1 and 2.l percent C and now known as UHCS) are described. The early use of steel compositions containing carbon contents above the eutectoid level is found in ancient weapons from around the world. For example, both Damascus and Japanese sword steels are hypereutectoid steels. Their manufacture and processing is of interest in understanding the role of carbon content in the development of modern steels. Although sporadic examples of UHCS compositions are found in steels examined in the early part of this century, it was not until the mid-1970s that the modern study began. This study had its origin in the development of superplastic behavior in steels and the recognition that increasing the carbon content was of importance in developing that property. The compositions that were optimal for superplasticity involved the development of steels that contained higher carbon contents than conventional modern steels. It was discovered, however, that the room temperature properties of these compositions were of interest in their own right. Following this discovery, a period of intense work began on understanding their manufacture, processing, and properties for both superplastic forming and room temperature applications. The development of superplastic cast irons and iron carbides, as well as those of laminated composites containing UHCS, was an important part of this history.

  5. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 2 2013-10-01 2013-10-01 false Carbon-steel or alloy-steel castings. 59.20-1 Section 59... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  6. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 2 2011-10-01 2011-10-01 false Carbon-steel or alloy-steel castings. 59.20-1 Section 59... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  7. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 2 2014-10-01 2014-10-01 false Carbon-steel or alloy-steel castings. 59.20-1 Section 59... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  8. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 2 2012-10-01 2012-10-01 false Carbon-steel or alloy-steel castings. 59.20-1 Section 59... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  9. 46 CFR 59.20-1 - Carbon-steel or alloy-steel castings.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Carbon-steel or alloy-steel castings. 59.20-1 Section 59... BOILERS, PRESSURE VESSELS AND APPURTENANCES Welding Repairs to Castings § 59.20-1 Carbon-steel or alloy-steel castings. Defects in carbon-steel or alloy-steel castings may be repaired by welding. The...

  10. Stainless Steel Permeability

    SciTech Connect

    Buchenauer, Dean A.; Karnesky, Richard A.

    2015-09-01

    An understanding of the behavior of hydrogen isotopes in materials is critical to predicting tritium transport in structural metals (at high pressure), estimating tritium losses during production (fission environment), and predicting in-vessel inventory for future fusion devices (plasma driven permeation). Current models often assume equilibrium diffusivity and solubility for a class of materials (e.g. stainless steels or aluminum alloys), neglecting trapping effects or, at best, considering a single population of trapping sites. Permeation and trapping studies of the particular castings and forgings enable greater confidence and reduced margins in the models. For FY15, we have continued our investigation of the role of ferrite in permeation for steels of interest to GTS, through measurements of the duplex steel 2507. We also initiated an investigation of the permeability in work hardened materials, to follow up on earlier observations of unusual permeability in a particular region of 304L forgings. Samples were prepared and characterized for ferrite content and coated with palladium to prevent oxidation. Issues with the poor reproducibility of measurements at low permeability were overcome, although the techniques in use are tedious. Funding through TPBAR and GTS were secured for a research grade quadrupole mass spectrometer (QMS) and replacement turbo pumps, which should improve the fidelity and throughput of measurements in FY16.

  11. High Fragmentation Steel Production Process

    DTIC Science & Technology

    1984-01-01

    phase of the project entailed the purchase and metallurgical characterization of two heats of HF-1 steel from different vendors. Performed by...At>-A 13^ nzt AD AD-E401 117 CONTRACTOR REPORT ARLCD-CR-83049 HIGH FRAGMENTATION STEEL PRODUCTION PROCESS ^"fP-PTTMirj A 1 James F. Kane...Report 6. PERFORMING ORG. REPORT NUMBER High Fragmentation Steel Production Process 7. AUTHORfs; James F. Kane, Ronald L. Kivak, Colin C. MacCrindle

  12. Process for dezincing galvanized steel

    DOEpatents

    Morgan, W.A.; Dudek, F.J.; Daniels, E.J.

    1998-07-14

    A process is described for removing zinc from galvanized steel. The galvanized steel is immersed in an electrolyte containing at least about 15% by weight of sodium or potassium hydroxide and having a temperature of at least about 75 C and the zinc is galvanically corroded from the surface of the galvanized steel. The material serving as the cathode is principally a material having a standard electrode potential which is intermediate of the standard electrode potentials of zinc and cadmium in the electrochemical series. The corrosion rate may be accelerated by (1) increasing the number density of corrosion sites in the galvanized steel by mechanically abrading or deforming the galvanized steel, (2) heating the galvanized steel to form an alloy of zinc on the surface of the galvanized steel, (3) mixing the galvanized steel with a material having a standard electrode potential which is intermediate of the standard electrode potentials of zinc and cadmium in the electrochemical series, or (4) moving the galvanized steel relative to itself and to the electrolyte while immersed in the electrolyte. 1 fig.

  13. Process for dezincing galvanized steel

    DOEpatents

    Morgan, William A.; Dudek, Frederick J.; Daniels, Edward J.

    1998-01-01

    A process for removing zinc from galvanized steel. The galvanized steel is immersed in an electrolyte containing at least about 15% by weight of sodium or potassium hydroxide and having a temperature of at least about 75.degree. C. and the zinc is galvanically corroded from the surface of the galvanized steel. The material serving as the cathode is principally a material having a standard electrode potential which is intermediate of the standard electrode potentials of zinc and cadmium in the electrochemical series. The corrosion rate may be accelerated by (i) increasing the number density of corrosion sites in the galvanized steel by mechanically abrading or deforming the galvanized steel, (ii) heating the galvanized steel to form an alloy of zinc on the surface of the galvanized steel, (iii) mixing the galvanized steel with a material having a standard electrode potential which is intermediate of the standard electrode potentials of zinc and cadmium in the electrochemical series, or (iv) moving the galvanized steel relative to itself and to the electrolyte while immersed in the electrolyte.

  14. High strength, tough alloy steel

    DOEpatents

    Thomas, Gareth; Rao, Bangaru V. N.

    1979-01-01

    A high strength, tough alloy steel is formed by heating the steel to a temperature in the austenite range (1000.degree.-1100.degree. C.) to form a homogeneous austenite phase and then cooling the steel to form a microstructure of uniformly dispersed dislocated martensite separated by continuous thin boundary films of stabilized retained austenite. The steel includes 0.2-0.35 weight % carbon, at least 1% and preferably 3-4.5% chromium, and at least one other substitutional alloying element, preferably manganese or nickel. The austenite film is stable to subsequent heat treatment as by tempering (below 300.degree. C.) and reforms to a stable film after austenite grain refinement.

  15. Hydrogen Embrittlement of Gun Steel

    DTIC Science & Technology

    1987-11-01

    8217s HY80 and HY130 steels were checked for the critical hydrogen concentrations which were determined to be 6 ppm for HY8O steel 8 and 3 ppm for HY130...JOTC FILE COPY AD-A188 972 AD 1 TECHNICAL REPORT ARCCB-TR-87030 HYDROGEN EMBRITTLEMENT OF GUN STEEL F’ GERALD L. SPFNCER DTIC DEC 1 5 1987 NOVEMBER...PtEtIOC COVERED HYDROGEN EMBRITTLEHENT OF GUN STEEL Final OG EOTNME 6. PERFORMINGORO EOTNME 7. A*JTNOR(s) S. CONTRACT OR GRANT NUMBER(&) Gerald L

  16. High pressure deuterium-tritium gas target vessels for muon-catalyzed fusion experiments

    SciTech Connect

    Caffrey, A.J.; Spaletta, H.W.; Ware, A.G.; Zabriskie, J.M.; Hardwick, D.A.; Maltrud, H.R.; Paciotti, M.A.; Los Alamos National Lab., NM )

    1989-01-01

    In experimental studies of muon-catalyzed fusion, the density of the hydrogen gas mixture is an important parameter. Catalysis of up to 150 fusions per muon has been observed in deuterium-tritium gas mixtures at liquid hydrogen density; at room temperature, such densities require a target gas pressure of the order of 1000 atmospheres (100 MPa, 15,000 psi). We report here the design considerations for hydrogen gas target vessels for muon-catalyzed fusion experiments that operate at 1000 and 10,000 atmospheres. The 1000 atmosphere high pressure target vessels are fabricated of Type A-286 stainless steel and lined with oxygen-free, high-conductivity (OFHC) copper to provide a barrier to hydrogen permeation of the stainless steel. The 10,000 atmosphere ultrahigh pressure target vessels are made from 18Ni (200 grade) maraging steel and are lined with OFHC copper, again to prevent hydrogen permeation of the steel. In addition to target design features, operating requirements, fabrication procedures, and secondary containment are discussed. 13 refs., 3 figs., 1 tab.

  17. ARc Welding (Industrial Processing Series).

    DTIC Science & Technology

    ARC WELDING , *BIBLIOGRAPHIES), (*ARC WELDS, BIBLIOGRAPHIES), ALUMINUM ALLOYS, TITANIUM ALLOYS, CHROMIUM ALLOYS, METAL PLATES, SPOT WELDING , STEEL...INERT GAS WELDING , MARAGING STEELS, MICROSTRUCTURE, HEAT RESISTANT ALLOYS, HEAT RESISTANT METALS, WELDABILITY, MECHANICAL PROPERTIES, MOLYBDENUM ALLOYS, NICKEL ALLOYS, RESISTANCE WELDING

  18. The industrial ecology of steel

    SciTech Connect

    Considine, Timothy J.; Jablonowski, Christopher; Considine, Donita M.M.; Rao, Prasad G.

    2001-03-26

    This study performs an integrated assessment of new technology adoption in the steel industry. New coke, iron, and steel production technologies are discussed, and their economic and environmental characteristics are compared. Based upon detailed plant level data on cost and physical input-output relations by process, this study develops a simple mathematical optimization model of steel process choice. This model is then expanded to a life cycle context, accounting for environmental emissions generated during the production and transportation of energy and material inputs into steelmaking. This life-cycle optimization model provides a basis for evaluating the environmental impacts of existing and new iron and steel technologies. Five different plant configurations are examined, from conventional integrated steel production to completely scrap-based operations. Two cost criteria are used to evaluate technology choice: private and social cost, with the latter including the environmental damages associated with emissions. While scrap-based technologies clearly generate lower emissions in mass terms, their emissions of sulfur dioxide and nitrogen oxides are significantly higher. Using conventional damage cost estimates reported in the literature suggests that the social costs associated with scrap-based steel production are slightly higher than with integrated steel production. This suggests that adopting a life-cycle viewpoint can substantially affect environmental assessment of new technologies. Finally, this study also examines the impacts of carbon taxes on steel production costs and technology choice.

  19. MINOS Detector Steel Magnetic Measurements

    SciTech Connect

    Robert C. Trendler and Walter F. Jaskierny

    1999-03-03

    Magnetic measurements were made on one steel plate of the MINOS far detector. The conventionally used technique of measuring sense coil voltage induced by step changes in excitation current voltage was successful in providing stable, repeatable measurements. Measurements were made at several locations on the steel and the results are presented.

  20. Hydrogen Embrittlement of Structural Steels

    SciTech Connect

    Somerday, Brian P.; San Marchi, Christopher W

    2014-08-01

    Carbon-manganese steels are candidates for the structural materials in hydrogen gas pipelines; however, it is well known that these steels are susceptible to hydrogen embrittlement. Decades of research and industrial experience have established that hydrogen embrittlement compromises the structural integrity of steel components. This experience has also helped identify the failure modes that can operate in hydrogen containment structures. As a result, there are tangible ideas for managing hydrogen embrittlement in steels and quantifying safety margins for steel hydrogen containment structures. For example, fatigue crack growth aided by hydrogen embrittlement is a well-established failure mode for steel hydrogen containment structures subjected to pressure cycling. This pressure cycling represents one of the key differences in operating conditions between current hydrogen pipelines and those anticipated in a hydrogen delivery infrastructure. Applying structural integrity models in design codes coupled with measurement of relevant material properties allows quantification of the reliability/integrity of steel hydrogen pipelines subjected to pressure cycling. Furthermore, application of these structural integrity models is aided by the development of physics-based predictive models, which provide important insights such as the effects of microstructure on hydrogen-assisted fatigue crack growth. Successful implementation of these structural integrity and physics-based models enhances confidence in the design codes and enables decisions about materials selection and operating conditions for reliable and efficient steel hydrogen pipelines.

  1. 2169 Steel Waveform Experiments

    NASA Astrophysics Data System (ADS)

    Furnish, M.; Alexander, C.; Reinhart, W.; Brown, J.

    2013-06-01

    In support of efforts to develop multiscale models of materials, we performed eight gas gun impact experiments on 2169 steel (21% Cr, 6% Ni, 9% Mn). These experiments provided shock, reshock and release velocimetry data, with initial shock stresses ranging from 10 to 50 GPa (particle velocities from 0.25 to 1.05 km/s). Both windowed and free-surface measurements were used, with samples 1 to 5 mm thick. The study focused on dynamic strength determination via the release/reshock paths. Reshock tests with explosively welded impactors produced clean results. The free-surface samples, which were steps on a single piece of steel, showed lower wavespeeds for thin (1 mm) samples than for thicker (2 or 4 mm) samples. A configuration used for the last three shots allowed release information to be determined from these free surface samples as well. The sample strength appears to increase with stress from ~1 GPa to ~3 GPa over this range, consistent with other recent work but about 40% above the Steinberg model. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

  2. Connections: Superplasticity, Damascus Steels, Laminated Steels, and Carbon Dating

    NASA Astrophysics Data System (ADS)

    Wadsworth, Jeffrey

    2016-12-01

    In this paper, a description is given of the connections that evolved from the initial development of a family of superplastic plain carbon steels that came to be known as Ultra-High Carbon Steels (UHCS). It was observed that their very high carbon contents were similar, if not identical, to those of Damascus steels. There followed a series of attempts to rediscover how the famous patterns found on Damascus steels blades were formed. At the same time, in order to improve the toughness at room temperature of the newly-developed UHCS, laminated composites were made of alternating layers of UHCS and mild steel (and subsequently other steels and other metals). This led to a study of ancient laminated composites, the motives for their manufacture, and the plausibility of some of the claims relating to the number of layers in the final blades. One apparently ancient laminated composite, recovered in 1837 from the great pyramid of Giza which was constructed in about 2750 B.C., stimulated a carbon dating study of ancient steels. The modern interest in "Bladesmithing" has connections back to many of these ancient weapons.

  3. Occupational Profiles in the European Steel Industry.

    ERIC Educational Resources Information Center

    Franz, Hans-Werner; And Others

    The steel industry in Europe has faced great changes, with resulting layoffs and restructuring. Now that the most basic changes seem to be over, it has become evident that the remaining steel industry requires more highly trained workers than was the case previously. Although steel maintenance employees were always highly skilled, steel production…

  4. 49 CFR 192.55 - Steel pipe.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Steel pipe. 192.55 Section 192.55 Transportation... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Materials § 192.55 Steel pipe. (a) New steel pipe is... in accordance with paragraph (c) or (d) of this section. (b) Used steel pipe is qualified for...

  5. 49 CFR 192.55 - Steel pipe.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Steel pipe. 192.55 Section 192.55 Transportation... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Materials § 192.55 Steel pipe. (a) New steel pipe is... in accordance with paragraph (c) or (d) of this section. (b) Used steel pipe is qualified for...

  6. 49 CFR 192.55 - Steel pipe.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Steel pipe. 192.55 Section 192.55 Transportation... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Materials § 192.55 Steel pipe. (a) New steel pipe is... in accordance with paragraph (c) or (d) of this section. (b) Used steel pipe is qualified for...

  7. 49 CFR 192.55 - Steel pipe.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Steel pipe. 192.55 Section 192.55 Transportation... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Materials § 192.55 Steel pipe. (a) New steel pipe is... in accordance with paragraph (c) or (d) of this section. (b) Used steel pipe is qualified for...

  8. 49 CFR 192.55 - Steel pipe.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Steel pipe. 192.55 Section 192.55 Transportation... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Materials § 192.55 Steel pipe. (a) New steel pipe is... in accordance with paragraph (c) or (d) of this section. (b) Used steel pipe is qualified for...

  9. Improving the toughness of ultrahigh strength steel

    SciTech Connect

    Soto, Koji

    2002-01-01

    The ideal structural steel combines high strength with high fracture toughness. This dissertation discusses the toughening mechanism of the Fe/Co/Ni/Cr/Mo/C steel, AerMet 100, which has the highest toughness/strength combination among all commercial ultrahigh strength steels. The possibility of improving the toughness of this steel was examined by considering several relevant factors.

  10. Hypereutectoid high-speed steels

    SciTech Connect

    Kremnev, L.S.

    1986-01-01

    Half of the tungsten and molybdenum contained in R6M5 and R18 steels is concentrated in the undissolved eutectic carbides hindering austenitic grain gowth in hardening and providing the necessary strength and impact strength. This article describes the tungsten-free low-alloy high-speed steel 11M5F with a chemical composition of 1.03-1.10% C, 5.2-5.7% Mo, 3.8-4.2% Cr, 1.3-1.7% V, 0.3-0.6% Si, and 0.3% Ce. The properties of 11M5F and R6M5 steels are examined and compared. The results of production and laboratory tests of the cutting properties of tools of the steels developed showed their high effectiveness, especially of 11M5F steel with 1% A1. The life of tools of the tungsten-free steels is two or three times greater than the life of tools of R6M5 steel.

  11. Welding tritium exposed stainless steel

    SciTech Connect

    Kanne, W.R. Jr.

    1994-11-01

    Stainless steels that are exposed to tritium become unweldable by conventional methods due to buildup of decay helium within the metal matrix. With longer service lives expected for tritium containment systems, methods for welding on tritium exposed material will become important for repair or modification of the systems. Solid-state resistance welding and low-penetration overlay welding have been shown to mitigate helium embrittlement cracking in tritium exposed 304 stainless steel. These processes can also be used on stainless steel containing helium from neutron irradiation, such as occurs in nuclear reactors.

  12. Method for welding chromium molybdenum steels

    SciTech Connect

    Sikka, V.K.

    1986-09-16

    A process is described for welding chromium-molybdenum steels which consist of: subjecting the steel to normalization by heating to above the transformation temperature and cooling in air; subjecting the steel to a partial temper by heating to a temperature less than a full temper; welding the steel using an appropriate filler metal; subjecting the steel to a full temper by heating to a temperature sufficient to optimize strength, reduce stress, increase ductility and reduce hardness.

  13. 2169 steel waveform experiments.

    SciTech Connect

    Furnish, Michael David; Alexander, C. Scott; Reinhart, William Dodd; Brown, Justin L.

    2012-11-01

    In support of LLNL efforts to develop multiscale models of a variety of materials, we have performed a set of eight gas gun impact experiments on 2169 steel (21% Cr, 6% Ni, 9% Mn, balance predominantly Fe). These experiments provided carefully controlled shock, reshock and release velocimetry data, with initial shock stresses ranging from 10 to 50 GPa (particle velocities from 0.25 to 1.05 km/s). Both windowed and free-surface measurements were included in this experiment set to increase the utility of the data set, as were samples ranging in thickness from 1 to 5 mm. Target physical phenomena included the elastic/plastic transition (Hugoniot elastic limit), the Hugoniot, any phase transition phenomena, and the release path (windowed and free-surface). The Hugoniot was found to be nearly linear, with no indications of the Fe phase transition. Releases were non-hysteretic, and relatively consistent between 3- and 5-mmthick samples (the 3 mm samples giving slightly lower wavespeeds on release). Reshock tests with explosively welded impactors produced clean results; those with glue bonds showed transient releases prior to the arrival of the reshock, reducing their usefulness for deriving strength information. The free-surface samples, which were steps on a single piece of steel, showed lower wavespeeds for thin (1 mm) samples than for thicker (2 or 4 mm) samples. A configuration used for the last three shots allows release information to be determined from these free surface samples. The sample strength appears to increase with stress from ~1 GPa to ~ 3 GPa over this range, consistent with other recent work but about 40% above the Steinberg model.

  14. Fatigue handbook: Offshore steel structures

    SciTech Connect

    Almarnaess, A.

    1985-01-01

    The contents of this book are: Overview of Offshore Steel Structures; Loads on Ocean Structures; Fracture Mechanics As a Tool in Fatigue Analysis; Basic Fatigue Properties of Welded Joints; Significance of Defects; Improving the Fatigue Strength of Welded Joints; Effects of Marine Environment and Cathodic Protection on Fatigue of Structural Steels Fatigue of Tubular Joints; Unstable Fracture; Fatigue Life Calculations; and Fatigue in Building Codes Background and Applications.

  15. Wear of steel by rubber

    NASA Technical Reports Server (NTRS)

    Gent, A. N.; Pulford, C. T. R.

    1978-01-01

    Wear of a steel blade used as a scraper to abrade rubber surfaces has been found to take place much more rapidly on a cis-polyisoprene (natural rubber) surface than on a cis-polybutadiene surface, and much more rapidly in an inert atmosphere than in air. These observations are attributed to the direct attack upon steel of free-radical species generated by mechanical rupture of elastomer molecules during abrasion.

  16. ELECTROMAGNETIC INSPECTION OF HARDENED STEEL.

    DTIC Science & Technology

    heat treat methods (no carbon added to the surface), and (2) The determination of through hardness or tempering temperature history of Stentor tool...effectiveness of phase sensitive and harmonic eddy current test methods for determining tempering temperature history of 4340 and Stentor tool steels was...showed that tempering temperature history of 4340 and Stentor steel can be determined for all temperatures (265 F to 820 F) used for specimen preparation on this program.

  17. Development of New Stainless Steel

    SciTech Connect

    Robert F. Buck

    2005-08-30

    A new family of innovative martensitic stainless steels, 521-A, 521-B, and 521-C has been developed by Advanced Steel Technology, LLC (Trafford, PA) as high strength fastener (bolt) materials for use at moderate temperatures in turbine engines, including steam turbines, gas turbines, and aircraft engines. The primary objective of the development program was to create a martensitic stainless steel with high strength at moderate temperatures, and which could replace the expensive nickel-based superalloy IN 718 in some fasteners applications. A secondary objective was to replace conventional 12Cr steels such as AISI 422 used as blades, buckets and shafts that operate at intermediate temperatures in turbine engines with stronger steel. The composition of the new alloys was specifically designed to produce excellent mechanical properties while integrating heat treatment steps into production to reduce energy consumption during manufacturing. As a result, production costs and energy consumption during production of rolled bar products is significantly lower than conventional materials. Successful commercialization of the new alloys would permit the installed cost of certain turbine engines to be reduced without sacrificing high availability or operational flexibility, thereby enhancing the global competitiveness of U.S. turbine engine manufacturers. Moreover, the domestic specialty steel industry would also benefit through increased productivity and reduced operating costs, while increasing their share of the international market for turbine engine fasteners, blades, buckets and shafts.

  18. Review on cold-formed steel connections.

    PubMed

    Lee, Yeong Huei; Tan, Cher Siang; Mohammad, Shahrin; Tahir, Mahmood Md; Shek, Poi Ngian

    2014-01-01

    The concept of cold-formed light steel framing construction has been widespread after understanding its structural characteristics with massive research works over the years. Connection serves as one of the important elements for light steel framing in order to achieve its structural stability. Compared to hot-rolled steel sections, cold-formed steel connections perform dissimilarity due to the thin-walled behaviour. This paper aims to review current researches on cold-formed steel connections, particularly for screw connections, storage rack connections, welded connections, and bolted connections. The performance of these connections in the design of cold-formed steel structures is discussed.

  19. Review on Cold-Formed Steel Connections

    PubMed Central

    Tan, Cher Siang; Mohammad, Shahrin; Md Tahir, Mahmood; Shek, Poi Ngian

    2014-01-01

    The concept of cold-formed light steel framing construction has been widespread after understanding its structural characteristics with massive research works over the years. Connection serves as one of the important elements for light steel framing in order to achieve its structural stability. Compared to hot-rolled steel sections, cold-formed steel connections perform dissimilarity due to the thin-walled behaviour. This paper aims to review current researches on cold-formed steel connections, particularly for screw connections, storage rack connections, welded connections, and bolted connections. The performance of these connections in the design of cold-formed steel structures is discussed. PMID:24688448

  20. 38. Photocopy of photograph. STEEL PLANT, BOILERS UNDER CONSTRUCTION IN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    38. Photocopy of photograph. STEEL PLANT, BOILERS UNDER CONSTRUCTION IN BOILER PLANT LOCATED EAST OF MAIN STEEL PLANT, 1909. (From the Bethlehem Steel Corporation collection, Seattle, WA) - Irondale Iron & Steel Plant, Port Townsend, Jefferson County, WA

  1. A Multipurpose Projectile for Penetrating Urban Targets

    DTIC Science & Technology

    2007-04-01

    experiments were fabricated from Vascomax 300 maraging steel (Allvac, 2006). A photograph of this projectile is shown in Figure 1. Six...The CRH=2 projectiles used in the second set of experiments were also fabricated from Vascomax 300 maraging steel . A photograph of the CRH=2...experiments included steel -reinforcing material (rebar). The rebar, however, was not represented in the Zapotec computational model of the target, nor

  2. Considerations of Nose Shape for Thin-Walled Projectile Penetrating Double Reinforced Concrete

    DTIC Science & Technology

    2008-07-01

    experiments were fabricated by ARL from Vascomax 300 maraging steel [6]. A photograph of this projectile is shown in Figure 1. Six projectiles...Experiments The CRH=2 projectiles used in the second set of experiments were also fabricated from Vascomax 300 maraging steel . A photograph of the CRH=2...In the Zapotec simulations, the concrete target material was modeled with a brittle fracture kinetics model [4]. The experiments included steel

  3. Nickel release from stainless steels.

    PubMed

    Haudrechy, P; Mantout, B; Frappaz, A; Rousseau, D; Chabeau, G; Faure, M; Claudy, A

    1997-09-01

    In 1994, a study of nickel release and allergic contact dermatitis from nickel-plated metals and stainless steels was published in this journal. It was shown that low-sulfur stainless steel grades like AISI 304, 316L or 430 (S < or = 0.007%) release less than 0.03 microgram/cm2/week of nickel in acid artificial sweat and elicit no reactions in patients already sensitized to nickel. In contrast, nickel-plated samples release around 100 micrograms/cm2/week of Ni and high-sulfur stainless steel (AISI 303-S approximately 0.3%) releases about 1.5 micrograms/cm2/week in this acid artificial sweat. Applied on patients sensitized to nickel, these metals elicit positive reactions in 96% and 14%, respectively, of the patients. The main conclusion was that low-sulfur stainless steels like AISI 304, 316L or 430, even when containing Ni, should not elicit nickel contact dermatitis, while metals having a mean corrosion resistance like a high-sulfur stainless steel (AISI 303) or nickel-plated steel should be avoided. The determining characteristic was in fact the corrosion resistance in chloride media, which, for stainless steels, is connected, among other factors, to the sulfur content. Thus, a question remained concerning the grades with an intermediate sulfur content, around 0.03%, which were not studied. They are the object of the study presented in this paper. 3 tests were performed: leaching experiments, dimethylglyoxime and HNO3 spot tests, and clinical patch tests; however, only stainless steels were tested: a low-sulfur AISI 304 and AISI 303 as references and 3 grades with a sulfur content around 0.03%: AISI 304L, AISI 304L added with Ca, AISI 304L+Cu. Leaching experiments showed that the 4 non-resulfurised grades released less than 0.5 microgram/cm2/week in acid sweat while the reulfurized AISI 303 released around or more than 0.5 microgram/cm2/week. This is explained by the poorer corrosion resistance of the resulfurized grade. Yet all these grades had the same

  4. 29 CFR 1926.754 - Structural steel assembly.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 29 Labor 8 2013-07-01 2013-07-01 false Structural steel assembly. 1926.754 Section 1926.754 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Steel Erection § 1926.754 Structural steel...) Tripping hazards. Shear connectors (such as headed steel studs, steel bars or steel lugs), reinforcing...

  5. 46 CFR 56.60-5 - Steel (High temperature applications).

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 2 2014-10-01 2014-10-01 false Steel (High temperature applications). 56.60-5 Section... SYSTEMS AND APPURTENANCES Materials § 56.60-5 Steel (High temperature applications). (a) (Reproduces 124.2... steel, plain nickel-alloy steel, carbon-manganese-alloy steel, manganese-vanadium-alloy steel,...

  6. 46 CFR 56.60-5 - Steel (High temperature applications).

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 2 2012-10-01 2012-10-01 false Steel (High temperature applications). 56.60-5 Section... SYSTEMS AND APPURTENANCES Materials § 56.60-5 Steel (High temperature applications). (a) (Reproduces 124.2... steel, plain nickel-alloy steel, carbon-manganese-alloy steel, manganese-vanadium-alloy steel,...

  7. 29 CFR 1926.754 - Structural steel assembly.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 8 2010-07-01 2010-07-01 false Structural steel assembly. 1926.754 Section 1926.754 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Steel Erection § 1926.754 Structural steel...) Tripping hazards. Shear connectors (such as headed steel studs, steel bars or steel lugs), reinforcing...

  8. 29 CFR 1926.754 - Structural steel assembly.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 29 Labor 8 2011-07-01 2011-07-01 false Structural steel assembly. 1926.754 Section 1926.754 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Steel Erection § 1926.754 Structural steel...) Tripping hazards. Shear connectors (such as headed steel studs, steel bars or steel lugs), reinforcing...

  9. 29 CFR 1926.754 - Structural steel assembly.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 29 Labor 8 2012-07-01 2012-07-01 false Structural steel assembly. 1926.754 Section 1926.754 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Steel Erection § 1926.754 Structural steel...) Tripping hazards. Shear connectors (such as headed steel studs, steel bars or steel lugs), reinforcing...

  10. 46 CFR 56.60-5 - Steel (High temperature applications).

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 2 2011-10-01 2011-10-01 false Steel (High temperature applications). 56.60-5 Section... SYSTEMS AND APPURTENANCES Materials § 56.60-5 Steel (High temperature applications). (a) (Reproduces 124.2... steel, plain nickel-alloy steel, carbon-manganese-alloy steel, manganese-vanadium-alloy steel,...

  11. 46 CFR 56.60-5 - Steel (High temperature applications).

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 2 2013-10-01 2013-10-01 false Steel (High temperature applications). 56.60-5 Section... SYSTEMS AND APPURTENANCES Materials § 56.60-5 Steel (High temperature applications). (a) (Reproduces 124.2... steel, plain nickel-alloy steel, carbon-manganese-alloy steel, manganese-vanadium-alloy steel,...

  12. 46 CFR 56.60-5 - Steel (High temperature applications).

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Steel (High temperature applications). 56.60-5 Section... SYSTEMS AND APPURTENANCES Materials § 56.60-5 Steel (High temperature applications). (a) (Reproduces 124.2... steel, plain nickel-alloy steel, carbon-manganese-alloy steel, manganese-vanadium-alloy steel,...

  13. 29 CFR 1926.754 - Structural steel assembly.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 29 Labor 8 2014-07-01 2014-07-01 false Structural steel assembly. 1926.754 Section 1926.754 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Steel Erection § 1926.754 Structural steel...) Tripping hazards. Shear connectors (such as headed steel studs, steel bars or steel lugs), reinforcing...

  14. Steel erected at A-3 Test Stand

    NASA Technical Reports Server (NTRS)

    2008-01-01

    Workers erect the first fabricated steel girders to arrive at the A-3 Test Stand at Stennis Space Center. Steel work began at the construction site Oct. 29 and is scheduled to continue into next spring.

  15. High-temperature brazing of stainless steel

    NASA Technical Reports Server (NTRS)

    Beuyukian, C. S.; Heisman, R. M.; Mitchell, M. J.

    1978-01-01

    Prevention of iron contamination of platens is eliminated by placing alumina/silica ceramic-fiber blankets between platens and carbon-steel plate. Carbon-steel plates provide rigidity and improve heat transfer.

  16. Corrosion control of steel-reinforced concrete

    NASA Astrophysics Data System (ADS)

    Chung, D. D. L.

    2000-10-01

    The methods and materials for corrosion control of steel-reinforced concrete are reviewed. The methods are steel surface treatment, the use of admixtures in concrete, surface coating on concrete, and cathodic protection.

  17. ESF GROUND SUPPORT - STRUCTURAL STEEL ANALYSIS

    SciTech Connect

    T. Misiak

    1996-06-26

    The purpose and objective of this analysis are to expand the level of detail and confirm member sizes for steel sets included in the Ground Support Design Analysis, Reference 5.20. This analysis also provides bounding values and details and defines critical design attributes for alternative configurations of the steel set. One possible configuration for the steel set is presented. This analysis covers the steel set design for the Exploratory Studies Facility (ESF) entire Main Loop 25-foot diameter tunnel.

  18. Copper-Nickel Cladding on Stainless Steel

    DTIC Science & Technology

    2005-07-01

    steel,. Monel (65Ni/35Cu) alloy consumables should be used as they can tolerate more iron dilution from the steel than the 70-30 copper-nickel alloy ...Cooper Alloys , 400 , K-500 Stainless Steel - Tyles 302, 304, 321, 347 N ickel 200 Silver Braze Alloys Nickel-Chromium Alloy 600 Nickel-Aluminum Bronze 70...cladding of austenitic stainless steels may also offer some ballistic, non-magnetic, and electromagnetic signature advantages over current hull alloys and

  19. Corrosion Behavior of Steel Fibrous Concrete

    DTIC Science & Technology

    1977-05-01

    Crvtaiue wi ,rerse sido it necessaty m’d Identify by block number) steel fibrous concrete corrosion cracked fibrous concrete 20 ABST RACT (Continue...dissolved gas in liq- Although chloride ions affect the rate of steel corro- uids. sion in concrete , corrosion can occur without them. Verbeck has...repcrted that steel subjected to a concrete Corrosion of steel will not occur without water. Not environment normally develops a protective oxide film

  20. Recycling steel automatically - through resource recovery

    SciTech Connect

    Foley, W.J.

    1997-12-01

    Last year, more than 55 percent of all steel cans were recycled. But no matter how effective the local recycling programs may be, some steel cans and other steel products are overlooked and appear in MSW. This missed steel fraction is automatically recycled by resource recovery facilities through magnetic separation. More than three-fourths of the operating resource recovery plants magnetically separate steel cans and other discarded steel items either pre- or post-combustion. Recovering ferrous scrap clearly reduces the post-combustion material that is landfilled and heightens the facilities` environmental performance. Both the resource recovery and steel industries must heighten public awareness of the benefits of automatic steel recycling. Magnetic separation at resource recovery facilities is a simple method of diverting what would otherwise be relegated as solid waste to the landfill. It should be recognized as an increasingly important and valued part of the resource recovery and steel industries` overall recycling efforts. This paper will discuss the status of steel can recycling in the United States, describe how recovered ferrous is beneficiated before recycling by the steel industry, and make recommendations for heightening awareness of the steel recycling contribution made by resource recovery facilities.

  1. Steel erected at A-3 Test Stand

    NASA Technical Reports Server (NTRS)

    2008-01-01

    Fabricated steel began arriving by truck Oct. 24 for construction of the A-3 Test Stand that will be used to test the engine for the nation's next generation of moon rockets. Within days workers from Lafayette Steel Erector Inc. began assembling the 16 steel stages needed on the foundation and footings poured in the previous year.

  2. Steeling and Resilience in Art Education

    ERIC Educational Resources Information Center

    Heise, Donalyn

    2014-01-01

    Steel is an incredibly strong alloy of iron and carbon. Due to its incredible strength and durability, this resilient material is commonly used for constructing buildings. The transitive verb "steeling" is defined in Miriam-Webster dictionary as "to fill with resolution or determination, as in, she 'steeled herself to face the…

  3. Evaluation of a diffusion/trapping model for hydrogen ingress in high-strength alloys. Final technical report, November 1988-November 1990

    SciTech Connect

    Pound, B.G.

    1990-11-14

    The objective of this research was to obtain the hydrogen ingress and trapping characteristics for a range of microstructures and so identify the dominant type of irreversible trap in different alloys. A diffusion/trapping model was used in conjunction with a potentiostatic pulse technique to study the ingress of hydrogen in three precipitation-hardened alloys (Inconel 718, Incoloy 925, and 18Ni maraging steel), two work-hardened alloys (Inconel 625 and Hastelloy C-276), titanium (pure and grade 2), and copper-enriched AISI 4340 steel in 1 mol/L acetic acid-1 mol/L sodium acetate containing 15 ppm arsenic oxide. In all cases except pure titanium, the data were shown to fit the interface-control form of the model and values were determined for the irreversible trapping constants (k) and the flux of hydrogen into the alloys. The density of irreversible trap defects were calculated from k and generally found to be in close agreement with the concentration of a specific heterogeneity in each alloy. Moreover, the trapping constants for the alloys were found to be consistent with their relative susceptibilities to hydrogen embrittlement.

  4. Teaching Steel Connections Using an Interactive Virtual Steel Sculpture

    ERIC Educational Resources Information Center

    Moaveni, Saeed; Chou, Karen C.

    2015-01-01

    Steel connections play important roles in the integrity of a structure, and many structural failures are attributed to connection failures. Connections are the glue that holds a structure together. The failures of the Hartford Coliseum in 1977, the Hyatt Regency Hotel in Kansas City in 1980, and the I-35W Bridge in Minneapolis in 2007 are all…

  5. Superhard Nanocrystalline Homometallic Stainless Steel on Steel for Seamless Coatings

    NASA Technical Reports Server (NTRS)

    Tobin, Eric J.; Hafley, R. (Technical Monitor)

    2002-01-01

    The objective of this work is to deposit nanocrystalline stainless steel onto steel substrates (homometallic) for enhanced wear and corrosion resistance. Homometallic coatings provide superior adhesion, and it has been shown that ultrafine-grained materials exhibit the increased hardness and decreased permeability desired for protective coatings. Nanocrystals will be produced by controlling nucleation and growth and use of an ion beam during deposition by e-beam evaporation or sputtering. Phase I is depositing 31 6L nanocrystalline stainless steel onto 31 6L stainless steel substrates. These coatings exhibit hardnesses comparable to those normally obtained for ceramic coatings such ZrO2, and possess the superior adhesion of seamless, homometallic coatings. Hardening the surface with a similar material also enhances adhesion, by avoiding problems associated with thermal and lattice mismatch. So far we have deposited nanocrystalline homometallic 316L stainless steel coatings by varying the ions and the current density of the ion beams. For all deposition conditions we have produced smooth, uniform, superhard coatings. All coatings exhibit hardness of at least 200% harder than that of bulk materials. Our measurements indicate that there is a direct relationship between nanohardness and the current density of the ion beam. Stress measurements indicate that stress in the films is increasingly proportional to current density of the ion beam. TEM, XPS, and XRD results indicate that the coated layers consist of FCC structure nanocrystallites with a dimension of about 10 to 20 nm. The Ni and Mo concentration of these coating are lower than those of bulk 316L but the concentration of Cr is higher.

  6. Bearing steels in the 21. century

    SciTech Connect

    Tsubota, Kazuichi; Sato, Toshio; Kato, Yoshiyuki; Hiraoka, Kazuhiko; Hayashi, Ryoji

    1998-12-31

    Oxygen content of bearing steel will be reduced to below 3 ppm in the year 2000 if the current trend for the reduction of oxygen in the steel continues. As a result, size of oxide inclusions will become smaller and the fatigue life will be doubled. From the viewpoint of life prediction, cleanliness evaluation methods currently used are not effective. Inclusion Rating Method by Statistics of Extreme is useful for both cleanliness evaluation and fatigue life prediction. Bearings made of suitably heat treated carbon steels or low alloy steels, which possess equivalent fatigue properties to bearing steels, will increase owing to the requirement for lower cost and better formability.

  7. Reduced-activation steels: Future development for improved creep strength

    NASA Astrophysics Data System (ADS)

    Klueh, R. L.

    2008-08-01

    Reduced-activation steels for fusion applications were developed in the 1980s to replace the elevated-temperature commercial steels first considered. The new steels were patterned after the commercial steels, with the objective that the new steels have yield stress and ultimate tensile strength and impact toughness in a Charpy test comparable to or better than the steels they replaced. That objective was achieved in reduced-activation steels developed in Japan, Europe, and the United States. Although tensile and impact toughness of the reduced-activation steels exceed those of the commercial steels they were patterned after, their creep-rupture properties are inferior to some commercial steels they replaced. They are even more inferior to commercial steels developed since the 1980s. In this paper, compositional differences between reduced-activation steels and new commercial steels are examined, and compositions are proposed for development of new-and-improved reduced-activation steels.

  8. STEFINS: a steel freezing integral simulation program

    SciTech Connect

    Frank, M.V.

    1980-09-01

    STEFINS (STEel Freezing INtegral Simulation) is a computer program for the calculation of the rate of solidification of molten steel on solid steel. Such computations arize when investigating core melt accidents in fast reactors. In principle this problem involves a coupled two-dimensional thermal and hydraulic approach. However, by physically reasonable assumptions a decoupled approach has been developed. The transient solidification of molten steel on a cold wall is solved in the direction normal to the molten steel flow and independent from the solution for the molten steel temperature and Nusselt number along the direction of flow. The solutions to the applicable energy equations have been programmed in cylindrical and slab geometries. Internal gamma heating of steel is included.

  9. Thermal Linear Expansion of Nine Selected AISI Stainless Steels

    DTIC Science & Technology

    1978-04-01

    stainless steels. The nine selected stainless steels are AISI 303, 304, 304L, 316, 317, 321, 347, 410 , and 430. The recoended values Include the...point of the stainless steels. The nine selected stainless steels are AISI 303, 304, 304L, 316, 317, 321, 347, 410 , and 430. The recommended values...Stainless Steel..................................26 8. AISI 410 Stainless Steel..................................29 9. AISI 430 Stainless Steel

  10. Comparative Structural Strength Research of Hardened Carbon Steel and Hot-Rolled Alloy Steel

    NASA Astrophysics Data System (ADS)

    Bogomolov, A. V.; Zhakupov, A. N.; Kanayev, A. T.; Sikach, I. A.; Tugumov, K. K.

    2016-08-01

    Experiments on quantitative evaluation of fatigue strength showed that St5ps and St5sp carbon steels with A400 strength class can be fully applied for erection of constructions and buildings having cyclical loads during operation. Study of corrosion resistance of hardened carbon steel in comparison with hot-rolled alloy steel consists in difference in structures and hence, difference in intensity of electric and chemical processes featuring presence of steel in concrete. Structure of St5sp steel with A400 strength class in surface area has significantly less corrosion rate than ferritic-perlitic structure of 35GS steel with A400 strength class.

  11. [Radioactivity monitoring of steel processing in Croatian steel mills and foundries].

    PubMed

    Sofilić, Tahir; Marjanović, Tihana; Rastovcan-Mioc, Alenka

    2006-03-01

    The last twenty years have seen a number of cases of radioactive pollution in metallurgical industry. Therefore many metal producers have implemented systematic monitoring of radioactivity in their production processes, especially in steel processing, steel being the most applied construction material with the annual world output of over billion tonnes. Learning from the experience of the best known steel producers in Europe and the world Croatian steel mills have introduced radioactivity surveillance and control systems for radioactive elements in steel scrap, semi-finished and finished products. This paper argues in favour of radioactivity surveillance and control systems in steel and steel castings production in Croatia, and describes current systems and solutions available. Since we lack our own standards and regulations to control both domestic and imported steel scrap, semi-finished products (crude steel, hot and cold rolled strip) and finished products, we need to start implementing radioactivity surveillance and control systems in our steel and steel castings production applying the current international recommendations and guidelines, until we build up our own monitoring system and adopt legislation on the national level. This paper gives an overview of the basic types of radioactivity surveillance and control systems, the most frequent requirements to be met, as well as of the measurement and information flow in their application in steel and steel castings production.

  12. Microstructure and Mechanical Properties of HSLA-100 Steel

    DTIC Science & Technology

    1990-12-01

    13 Figure 4. High Strength Bainite Strength Components .................... 20 Figure 5. Bainitic Steel Tempering and DBTT ...21 Figure 6. Tempered Bainite Steel Yield Stress and DBTT .................. 21 Figure 7. HSLA-100 Steel Yield Strength versus Aging...Energy at -84°C ............... 31 Figure 14. HSLA-100 Steel Lot GQH DBTT ............................ 31 Figure 15. HSLA-100 Steel Lot GQH Ductility

  13. Bond characteristics of steel fiber and deformed reinforcing steel bar embedded in steel fiber reinforced self-compacting concrete (SFRSCC)

    NASA Astrophysics Data System (ADS)

    Aslani, Farhad; Nejadi, Shami

    2012-09-01

    Steel fiber reinforced self-compacting concrete (SFRSCC) is a relatively new composite material which congregates the benefits of the self-compacting concrete (SCC) technology with the profits derived from the fiber addition to a brittle cementitious matrix. Steel fibers improve many of the properties of SCC elements including tensile strength, ductility, toughness, energy absorption capacity, fracture toughness and cracking. Although the available research regarding the influence of steel fibers on the properties of SFRSCC is limited, this paper investigates the bond characteristics between steel fiber and SCC firstly. Based on the available experimental results, the current analytical steel fiber pullout model (Dubey 1999) is modified by considering the different SCC properties and different fiber types (smooth, hooked) and inclination. In order to take into account the effect of fiber inclination in the pullout model, apparent shear strengths (τ (app)) and slip coefficient (β) are incorporated to express the variation of pullout peak load and the augmentation of peak slip as the inclined angle increases. These variables are expressed as functions of the inclined angle (ϕ). Furthurmore, steel-concrete composite floors, reinforced concrete floors supported by columns or walls and floors on an elastic foundations belong to the category of structural elements in which the conventional steel reinforcement can be partially replaced by the use of steel fibers. When discussing deformation capacity of structural elements or civil engineering structures manufactured using SFRSCC, one must be able to describe thoroughly both the behavior of the concrete matrix reinforced with steel fibers and the interaction between this composite matrix and discrete steel reinforcement of the conventional type. However, even though the knowledge on bond behavior is essential for evaluating the overall behavior of structural components containing reinforcement and steel fibers

  14. Bond characteristics of steel fiber and deformed reinforcing steel bar embedded in steel fiber reinforced self-compacting concrete (SFRSCC)

    NASA Astrophysics Data System (ADS)

    Aslani, Farhad; Nejadi, Shami

    2012-09-01

    Steel fiber reinforced self-compacting concrete (SFRSCC) is a relatively new composite material which congregates the benefits of the self-compacting concrete (SCC) technology with the profits derived from the fiber addition to a brittle cementitious matrix. Steel fibers improve many of the properties of SCC elements including tensile strength, ductility, toughness, energy absorption capacity, fracture toughness and cracking. Although the available research regarding the influence of steel fibers on the properties of SFRSCC is limited, this paper investigates the bond characteristics between steel fiber and SCC firstly. Based on the available experimental results, the current analytical steel fiber pullout model (Dubey 1999) is modified by considering the different SCC properties and different fiber types (smooth, hooked) and inclination. In order to take into account the effect of fiber inclination in the pullout model, apparent shear strengths ( τ ( app)) and slip coefficient ( β) are incorporated to express the variation of pullout peak load and the augmentation of peak slip as the inclined angle increases. These variables are expressed as functions of the inclined angle ( ϕ). Furthurmore, steel-concrete composite floors, reinforced concrete floors supported by columns or walls and floors on an elastic foundations belong to the category of structural elements in which the conventional steel reinforcement can be partially replaced by the use of steel fibers. When discussing deformation capacity of structural elements or civil engineering structures manufactured using SFRSCC, one must be able to describe thoroughly both the behavior of the concrete matrix reinforced with steel fibers and the interaction between this composite matrix and discrete steel reinforcement of the conventional type. However, even though the knowledge on bond behavior is essential for evaluating the overall behavior of structural components containing reinforcement and steel fibers

  15. Longer Life for Steel Structures

    NASA Technical Reports Server (NTRS)

    1990-01-01

    IC 531 is a coating manufactured and marketed by Inorganic Coatings, Inc. The coating was developed by Goddard to protect structures at Kennedy Space Center. It is a high ratio potassium silicate formula. The coating is water based, nontoxic, and nonflammable. It generates no volatile organic compounds nor hazardous chemical waste, and bonds to steel in 30 minutes. At the present time, no one can say for sure how long IC 531's effective lifetime is. Some of the original Goddard test applications of 1976 are still going strong after lengthy exposure to the Sun, salt and moisture. Says IC in company literature: 'IC 531 offers virtually permanent protection for steel. We predict it will protect structures for well beyond 25 years. If necessary, it is infinitely maintainable; if damaged, it can easily be touched up with more IC 531.'

  16. Underwater wet welding of steel

    SciTech Connect

    Ibarra, S.; Liu, S.; Olson, D.L.

    1995-05-01

    Underwater wet welding is conducted directly in water with the shielded metal arc (SMA) and flux cored arc (FCA) welding processes. Underwater wet welding has been demonstrated as an acceptable repair technique down to 100 meters (325 ft.) in depth, but wet welds have been attempted on carbon steel structures down to 200 meters (650 ft.). The primary purpose of this interpretive report is to document and evaluate current understanding of metallurgical behavior of underwater wet welds so that new welding consumables can be designed and new welding practices can be developed for fabrication and repair of high strength steel structures at greater depths. First the pyrometallurgical and physical metallurgy behaviors of underwater weldments are discussed. Second, modifications of the welding consumables and processes are suggested to enhance the ability to apply wet welding techniques.

  17. Steel Industry Energy Bandwidth Study

    SciTech Connect

    none,

    2004-10-01

    ITP conducted a study on energy use and potential savings, or "bandwidth" study, in major steelmaking processes. Intended to provide a realistic estimate of the potential amount of energy that can be saved in an industrial process, the "bandwidth" refers to the difference between the amount of energy that would be consumed in a process using commercially available technology versus the minimum amount of energy needed to achieve those same results based on the 2nd law of thermodynamics. The Steel Industry Energy Bandwidth Study (PDF 133 KB) also estimates steel industry energy use in the year 2010, and uses that value as a basis for comparison against the minimum requirements. This energy savings opportunity for 2010 will aid focus on longer term R&D.

  18. Existing Steel Railway Bridges Evaluation

    NASA Astrophysics Data System (ADS)

    Vičan, Josef; Gocál, Jozef; Odrobiňák, Jaroslav; Koteš, Peter

    2016-12-01

    The article describes general principles and basis of evaluation of existing railway bridges based on the concept of load-carrying capacity determination. Compared to the design of a new bridge, the modified reliability level for existing bridges evaluation should be considered due to implementation of the additional data related to bridge condition and behaviour obtained from regular inspections. Based on those data respecting the bridge remaining lifetime, a modification of partial safety factors for actions and materials could be respected in the bridge evaluation process. A great attention is also paid to the specific problems of determination of load-caring capacity of steel railway bridges in service. Recommendation for global analysis and methodology for existing steel bridge superstructure load-carrying capacity determination are described too.

  19. Light microscopy of carbon steels

    SciTech Connect

    Samuels, L.E.

    1998-12-31

    Containing over 1,200 representative micrographs and the information and explanatory text that makes them really useful: composition, condition, etchant, and magnification, and more than 100 graphs and tables, this how to book not only gives everyday working examples, but also discusses the relationship between the constitution, metallurgy, and microstructure of various carbon steel products. Written by a renowned expert in metallography, this definitive work is a must for all those working in this area. Contents include: nomenclature of phases and constituents; phase transformations; low-carbon irons and steels; annealing and normalizing; spheroidization and graphitization; austenitization; transformation of austenite; tempering of martensite; welding; surface oxidation, decarburation; and oxidation scaling; glossary of terms; etching methods; conversion tables.

  20. Welding of high chromium steels

    NASA Technical Reports Server (NTRS)

    Miller, W B

    1928-01-01

    A brief description is given of different groups of high chromium steels (rustless iron and stainless steels) according to their composition and more generally accepted names. The welding procedure for a given group will be much the same regardless of the slight variations in chemical composition which may exist within a certain group. Information is given for the tensile properties (yield point and ultimate strength) of metal sheets and welds before and after annealing on coupons one and one-half inches wide. Since welds in rustless iron containing 16 to 18 percent chromium and 7 to 12 percent nickel show the best combination of strength and ductility in the 'as welded' or annealed condition, it is considered the best alloy to use for welded construction.

  1. Steel Industry Marginal Opportunity Analysis

    SciTech Connect

    none,

    2005-09-01

    The Steel Industry Marginal Opportunity Analysis (PDF 347 KB) identifies opportunities for developing advanced technologies and estimates both the necessary funding and the potential payoff. This analysis determines what portion of the energy bandwidth can be captured through the adoption of state-of-the-art technology and practices. R&D opportunities for addressing the remainder of the bandwidth are characterized and plotted on a marginal opportunity curve.

  2. Nano-composite stainless steel

    DOEpatents

    Dehoff, Ryan R.; Blue, Craig A.; Peter, William H.; Chen, Wei; Aprigliano, Louis F.

    2015-07-14

    A composite stainless steel composition is composed essentially of, in terms of wt. % ranges: 25 to 28 Cr; 11 to 13 Ni; 7 to 8 W; 3.5 to 4 Mo; 3 to 3.5 B; 2 to 2.5 Mn; 1 to 1.5 Si; 0.3 to 1.7 C; up to 2 O; balance Fe. The composition has an austenitic matrix phase and a particulate, crystalline dispersed phase.

  3. A study of Damascus steel

    SciTech Connect

    Berge, P.

    1995-02-16

    The Damascus sword has been an article of fascination for many years to blade collectors and metallurgists alike. The blades were given their name by Europeans who encountered these blades which originated from Damascus, Syria. They are best known for the appearance of the blade face. Genuine Damascus blades show swirling patterns of alternating light and dark regions which are due to the microstructure of the steel. The microstructure consists of arrays of well rounded cementite patterns in a matrix of either pearlite, bainite, or martensite. When this structure is etched the matrix will turn dark leaving the cementite particles light. Although many blades were produced over the centuries, while some of the process is known the making of a genuine Damascus blade today is generally considered a lost art. Many scientists have studied the subject in an attempt to understand the complex process by which the clustered arrays of cementite particles develop in the steel blades. The most prominent theories to date are presented in the General Introduction to this thesis. The thesis is divided into four main parts. In the first part, four proposed mechanisms of cementite cluster sheet formation as they relate to the banding theory are introduced. Experiments to investigate these mechanisms are presented. In Part II, collaborative research focused on the methodology of the reconstructed process for making Damascus steel is presented. In the third part, a study into the graphitization of the reconstructed blades is presented. In Part IV, experimental attempts at producing Damascus steel ingots in the laboratory are presented.

  4. Preparation and characterization of 304 stainless steel/Q235 carbon steel composite material

    NASA Astrophysics Data System (ADS)

    Shen, Wenning; Feng, Lajun; Feng, Hui; Cao, Ying; Liu, Lei; Cao, Mo; Ge, Yanfeng

    The composite material of 304 stainless steel reinforced Q235 carbon steel has been prepared by modified hot-rolling process. The resulted material was characterized by scanning electron microscope, three-electrode method, fault current impact method, electrochemical potentiodynamic polarization curve measurement and electrochemical impedance spectroscopy. The results showed that metallurgical bond between the stainless steel layer and carbon steel substrate has been formed. The composite material exhibited good electrical conductivity and thermal stability. The average grounding resistance of the composite material was about 13/20 of dip galvanized steel. There has no surface crack and bubbling formed after fault current impact. The composite material led to a significant decrease in the corrosion current density in soil solution, compared with that of hot dip galvanized steel and bare carbon steel. On the basis polarization curve and EIS analyses, it can be concluded that the composite material showed improved anti-corrosion property than hot-dip galvanized steel.

  5. 77 FR 67400 - RG Steel Wheeling, LLC, a Division of RG Steel, LLC, Doing Business as Wheeling Corrugating...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-11-09

    ... Employment and Training Administration RG Steel Wheeling, LLC, a Division of RG Steel, LLC, Doing Business as..., 2012, applicable to workers of RG Steel Wheeling, LLC, a division of RG Steel, LLC, doing business as... RG Steel, LLC, doing business as Wheeling Corrugating Company, Beech Bottom, West Virginia,...

  6. Nickel: makes stainless steel strong

    USGS Publications Warehouse

    Boland, Maeve A.

    2012-01-01

    Nickel is a silvery-white metal that is used mainly to make stainless steel and other alloys stronger and better able to withstand extreme temperatures and corrosive environments. Nickel was first identified as a unique element in 1751 by Baron Axel Fredrik Cronstedt, a Swedish mineralogist and chemist. He originally called the element kupfernickel because it was found in rock that looked like copper (kupfer) ore and because miners thought that "bad spirits" (nickel) in the rock were making it difficult for them to extract copper from it. Approximately 80 percent of the primary (not recycled) nickel consumed in the United States in 2011 was used in alloys, such as stainless steel and superalloys. Because nickel increases an alloy's resistance to corrosion and its ability to withstand extreme temperatures, equipment and parts made of nickel-bearing alloys are often used in harsh environments, such as those in chemical plants, petroleum refineries, jet engines, power generation facilities, and offshore installations. Medical equipment, cookware, and cutlery are often made of stainless steel because it is easy to clean and sterilize. All U.S. circulating coins except the penny are made of alloys that contain nickel. Nickel alloys are increasingly being used in making rechargeable batteries for portable computers, power tools, and hybrid and electric vehicles. Nickel is also plated onto such items as bathroom fixtures to reduce corrosion and provide an attractive finish.

  7. Recycling steel. Conducting a waste audit.

    PubMed

    Crawford, G

    1996-01-01

    This is the second in a series of three articles regarding steel can recycling from foodservice operations of healthcare facilities. This article highlights the basic methods of recycling steel cans, and includes information on conducting a waste audit and negotiating with a hauler regarding the benefits of recycling. The previous article discussed how steel is recycled across the country. The next article will convey a case history of actual foodservice recycling practice from a healthcare facility.

  8. Nonmetallic Inclusions in HSLA Steel Weldments

    DTIC Science & Technology

    1989-12-01

    lowering the DBTT . Nickel prevents the hot shortness phenomenon often observed in copper-bearing steels . Nickel is also an austenite stabilizer. By lowering... STEEL WELDMENTS by Brent A. Douglas December, 1989 Thesis Advisor Alan G. Fox Approved for public release; distribution is unlimited. 90 ,-. S...ACCESSION NO. II. TITLE (Incude Security Claw fication) Nonmetallic Inclusions In HSLA Steel Weldments IZ. PERSONAL AUTHOR(S) Douglas, Brent A. 138

  9. Evaluation of the Benefits of HSLA Steels

    DTIC Science & Technology

    1989-03-01

    quenched and tempered steels , such as HY80 and HY1OO, require preheat and interpass temperature controls during welding of plates thicker than 1/2 inch...interpass tempera- tures and heat input limitations. Strict adherence to these requirements is mandatory to avoid cracking in hydrogen- sensitive steels ...requirement and excellent weldability of this steel will probably lower produc- tion costs and cracking -related repairs enough to overcome the slight

  10. Bending Properties of Al-Steel and Steel-Steel Composite Metal Foams

    NASA Astrophysics Data System (ADS)

    Brown, Judith A.; Vendra, Lakshmi J.; Rabiei, Afsaneh

    2010-11-01

    The performance of new composite metal foams (CMFs) under bending was evaluated with simultaneous acoustic emission (AE) monitoring on samples processed by cast and powder metallurgy (PM) techniques. The results showed high maximum strength in all samples up to 86 MPa with more ductile failure in PM samples. Acoustic emission behavior confirmed that the dominating failure mechanism of cast CMF is the brittle fracture of intermetallic phases that mostly exist at the interface of the steel spheres with the aluminum matrix, whereas in PM samples (100 pct steel), the failure is governed by the propagation of preexisting microporosities in the matrix resulting in a complete ductile failure. SEM imaging of the fracture surfaces supported these findings.

  11. Modified 43XX Steels for High Toughness

    DTIC Science & Technology

    1980-04-01

    AL AMMRC TR 80-20 MODIFIED 43XX STEELS FOR HIGH TOUGHNESS T CS.,•, °x ,•, o o,,o,,,sD T I W4 AftELECTE APRIL 1980 J N.J. Kar, V.F. Zackay and E.R...carried out. Isohra tasomions in these steels resulted inn bbaainni 11-v DI FOR Z 47 RITIOW OF I NOV695 IS OBSOLETE UCASFE SECURITY UCLASSIFIEDINOFTI PAGE...this investigation for Si-modified AISI 4330 steel appear to be superior to those for unmodified AISI 4340 and 300-M steels , whilst the strength-tough

  12. Fracture Characteristics of Structural Steels and Weldments

    DTIC Science & Technology

    1975-11-01

    constrctionTECHNICAL REPORT`M.170 engineringNovember 1975 research laboratory FRACTURE CHARACTERISTICS OF STRUCTURAL STEELS AND WELDMENTS by J...microscope structure steel steel weldments 2 0. AUS51RA.Y’ Ztiu is~~g e ".C f ,e owl mod Idwisf~yb 6405 ". b mbef This5 tepof I p)wnh~t tlie tiIodings...CLALUVICA1IOli Of UAE(.0’ LINCLASSTFI~n SECURITY CLASSIFICATION Of THIS PAQE(1h.M Data EntWOO4 The hydrogen-enibrittled, high-strength steels exhibited

  13. Corrosion of stainless steel, 2. edition

    SciTech Connect

    Sedriks, A.J.

    1996-10-01

    The book describes corrosion characteristics in all the major and minor groups of stainless steels, namely, in austenitic, ferritic, martensitic, duplex, and precipitation hardenable steels. Several chapters are spent on those special forms of corrosion that are investigated in the great detail in stainless steels, namely, pitting corrosion, crevice corrosion, and stress corrosion cracking. The influences of thermal treatment (heat affected zone cases), composition, and microstructure on corrosion are given good coverage. Corrosive environments include high temperature oxidation, sulfidation as well as acids, alkalis, various different petroleum plant environments, and even human body fluids (stainless steels are commonly used prosthetic materials).

  14. Recycling steel automatically -- through resource recovery

    SciTech Connect

    Crawford, G.L.

    1996-12-31

    More than three-fourths of the operating resource recovery plants magnetically separate steel cans and other discarded steel items either pre- or post-combustion. This last year, 121 resource recovery facilities combusted about 14% of the solid waste for communities across the US. Automatic recycling of steel clearly reduces the post-combustion material that is landfilled and heightens the facilities environmental performance through tangible recycling achievement. Even though about one out of every six steel cans is recycled automatically through resource recovery, not many people are aware of automatic recycling of steel cans through resource recovery. How many people know that their local resource recovery plant is insuring that virtually all of their food, beverage and general purpose cans--including paint and aerosol--are being recycled so easily and efficiently? Magnetic separation at resource recovery facilities is a fundamentally simple and desirable method of diverting what would otherwise be relegated as solid waste to the landfill. It should be recognized as an increasingly important and valued part of the resource recovery and steel industries overall recycling efforts. This paper will provide the latest information on steel recycled automatically from resource recovery facilities within the total context of all recycling accomplished annually by the steel industry. Most important, recommendations are provided for building public awareness of the automatic steel recycling contribution made so solidly by resource recovery facilities.

  15. 30. Photocopy of photograph. STEEL PLANT, OPEN HEARTH FURNACE CHARGING ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    30. Photocopy of photograph. STEEL PLANT, OPEN HEARTH FURNACE CHARGING CREW, 1910. (From the Bethlehem Steel Corporation Colletion, Seattle, WA) - Irondale Iron & Steel Plant, Port Townsend, Jefferson County, WA

  16. 37. Photocopy of photograph. STEEL PLANT, OPEN HOUSE INSIDE PLANT ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    37. Photocopy of photograph. STEEL PLANT, OPEN HOUSE INSIDE PLANT AT TIME OF ITS OPENING, 1910. (From the Bethlehem Steel Corporation Collection, Seattle, WA) - Irondale Iron & Steel Plant, Port Townsend, Jefferson County, WA

  17. North and west facades of crucible steel building; looking southeast ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    North and west facades of crucible steel building; looking southeast - Bethlehem Steel Corporation, South Bethlehem Works, Crucible Steel Plant, Along Lehigh River, North of Fourth Street, West of Minsi Trail Bridge, Bethlehem, Northampton County, PA

  18. Steel shear walls, behavior, modeling and design

    SciTech Connect

    Astaneh-Asl, Abolhassan

    2008-07-08

    In recent years steel shear walls have become one of the more efficient lateral load resisting systems in tall buildings. The basic steel shear wall system consists of a steel plate welded to boundary steel columns and boundary steel beams. In some cases the boundary columns have been concrete-filled steel tubes. Seismic behavior of steel shear wall systems during actual earthquakes and based on laboratory cyclic tests indicates that the systems are quite ductile and can be designed in an economical way to have sufficient stiffness, strength, ductility and energy dissipation capacity to resist seismic effects of strong earthquakes. This paper, after summarizing the past research, presents the results of two tests of an innovative steel shear wall system where the boundary elements are concrete-filled tubes. Then, a review of currently available analytical models of steel shear walls is provided with a discussion of capabilities and limitations of each model. We have observed that the tension only 'strip model', forming the basis of the current AISC seismic design provisions for steel shear walls, is not capable of predicting the behavior of steel shear walls with length-to-thickness ratio less than about 600 which is the range most common in buildings. The main reasons for such shortcomings of the AISC seismic design provisions for steel shear walls is that it ignores the compression field in the shear walls, which can be significant in typical shear walls. The AISC method also is not capable of incorporating stresses in the shear wall due to overturning moments. A more rational seismic design procedure for design of shear walls proposed in 2000 by the author is summarized in the paper. The design method, based on procedures used for design of steel plate girders, takes into account both tension and compression stress fields and is applicable to all values of length-to-thickness ratios of steel shear walls. The method is also capable of including the effect of

  19. Clean steel technology -- Fundamental to the development of high performance steels

    SciTech Connect

    Wilson, A.D.

    1999-07-01

    The use of clean steel technology (low sulfur with calcium treatment for inclusion shape control) is a fundamental building block in the development of high performance plate steels. A brief review will be presented of the benefits of calcium treatment and its effect on non-metallic inclusions (sulfides and oxides) and reducing sulfur levels. During the past thirty years the requirements for low sulfur levels have been reduced from 0.010% maximum to 0.001% maximum. The effects of clean steel practices on specific properties will be reviewed including tensile ductility, Charpy V-notch and fracture toughness, fatigue crack propagation and hydrogen-induced-cracking resistance. Traditional low sulfur plate steel applications have included pressure vessels. offshore platforms, plastic injection molds and line-pipe skelp. More recent applications will be discussed including bridge steels, high strength structural steels to 130 ksi (897 MPa) minimum yield strength, 9% nickel steels for cryogenic applications, and military armor.

  20. Corrosion Behavior of IF Steel in Various Media and Its Comparison with Mild Steel

    NASA Astrophysics Data System (ADS)

    Singh, G. P.; Moon, A. P.; Sengupta, S.; Deo, G.; Sangal, S.; Mondal, K.

    2015-05-01

    The present work discusses corrosion behavior of an interstitial-free (IF) steel in 0.6 M NaCl, 1 M NaOH, and 1 M HCl solutions, and its comparison with mild steel (MS). Dynamics polarization and AC Impedance Spectroscopy explain different polarization behaviors of the steel samples. All the steels were exposed to open atmosphere for 100 days, and to 0.6 M NaCl salt fog for 30 days. Scanning electron microscopy, x-ray diffraction, and Raman and Fourier Transformed Infrared Spectroscopy were used to characterize microstructure of the steels, rust constituents, and morphologies. Corrosion behavior of the steels has close relation with the morphology and constituents of the rusts. It has been observed that the corrosion in the IF and MS steels is uniform in nature.

  1. Help for the Steel Industry

    NASA Astrophysics Data System (ADS)

    1991-01-01

    A collaboration between NASA Lewis Research Center (LRC) and Gladwin Engineering resulted in the adaptation of aerospace high temperature metal technology to the continuous casting of steel. The continuous process is more efficient because it takes less time and labor. A high temperature material, once used on the X-15 research plane, was applied to metal rollers by a LRC developed spraying technique. Lewis Research Center also supplied mold prototype of metal composites, reducing erosion and promoting thermal conductivity. Rollers that previously cracked due to thermal fatigue, lasted longer. Gladwin's sales have increased, and additional NASA-developed innovations are anticipated.

  2. Chromizing of 3Cr Steel

    SciTech Connect

    Ravi, Vilupanur; Harrison, Bradley; Koch, Jordan; Ly, Alexander; Schissler, Andrew; Pint, Bruce A; Haynes, James A

    2011-01-01

    Grade 315 steel (Fe-2.9 Cr-1.7 W-0.7 Mo-0.3 Mn-0.3 Si-0.2 V-0.1 Ni-0.13 C-0.01 N) was chromized by the halide-activated pack cementation (HAPC) process. Key process parameters, i.e., coating temperatures and pack compositions, were investigated. Ammonium chloride-activated packs in the 700-1000 C range produced coatings nominally in the 1-8 {micro}m range, as determined by optical and scanning electron microscopy (SEM). Coatings applied in the 900-1000 C temperature range resulted in Cr-rich coatings. The predominant phase in the coating was identified as Cr23C6 by X-ray diffraction. In addition, the presence of chromium nitride, Cr2N, was observed in the coating. The power generation industry is faced with an ever-increasing demand for energy while simultaneously having to reduce carbon emissions. These goals can be facilitated by increasing plant efficiency through the use of higher operating temperatures and pressures. Traditional construction materials, e.g., the ferritic Grade 22 high strength low alloy steel, are limited to operations below {approx} 550 C. Therefore, new materials are required for future plants designed to operate up to 650 C and possibly higher. These new materials need to have improved tensile strength, ductility, toughness, corrosion resistance, and creep properties at elevated temperatures. Oak Ridge National Laboratory (ORNL) is investigating the oxidation and creep behavior of various coatings on Grade 315 steel (Fe-2.9 Cr-1.7 W-0.7 Mo-0.3 Mn-0.3 Si-0.2 V-0.1 Ni-0.13 C-0.01 N), a super-bainitic steel developed for superior creep properties. Thin, chemical vapor-deposited (CVD) aluminide coatings were used to compensate for the reduced corrosion and oxidation resistance that resulted from the low chromium content of the alloy. However, the aluminized Grade 315 alloys performed less-than-favorably under conditions relevant to fossil boilers, leading to the conclusion that higher chromium contents are required for the formation of

  3. Diffusion brazing nickel-plated stainless steel

    NASA Technical Reports Server (NTRS)

    Beuyukian, C. S.; Mitchell, M. J.

    1976-01-01

    To bond parts, sandwich assembly is made up of aluminum core, aluminum face sheet with brazing alloy interface, and nickel plated stainless steel part. Sandwich is placed between bottom and top glide sheet that is placed in stainless steel retort where assembly is bonded at 580 C.

  4. Technological properties of steels of martensitic class

    NASA Astrophysics Data System (ADS)

    Kleiner, L. M.; Greben'kov, S. K.; Zakirova, M. G.; Tolchina, I. V.; Ryaposov, I. V.

    2011-03-01

    Process, design, and ecological advantages of low-carbon martensitic steels (LCMS) are presented as compared to medium-carbon heat-treatable structural steels with a structure of tempered sorbite. The factors ensuring high manufacture adaptability in all stages of the production cycle are considered. Technological properties of widely used commercial weldable LCMS are analyzed.

  5. Method for welding chromium molybdenum steels

    DOEpatents

    Sikka, Vinod K.

    1986-01-01

    Chromium-molybdenum steels exhibit a weakening after welding in an area adjacent to the weld. This invention is an improved method for welding to eliminate the weakness by subjecting normalized steel to a partial temper prior to welding and subsequently fully tempering the welded article for optimum strength and ductility.

  6. History dependence of magnetomechanical properties of steel

    NASA Astrophysics Data System (ADS)

    Melquiond, F.; Mouroux, A.; Jouglar, J.; Vuillermoz, P. L.; Weinstock, H.

    1996-05-01

    Magnetomechanical measurements using a superconducting SQUID magnetic gradiometer and a tensile-testing machine have been performed on a variety of steel specimens to determine the change in magnetization due to applied stress and the possible application of the observed behavior as a new form of nondestructive evaluation in steel. This study builds on earlier related measurements.

  7. A recycling process for dezincing steel scrap

    SciTech Connect

    Dudek, F.J.; Daniels, E.J. ); Morgan, W.A.; Kellner, A.W.; Harrison, J. )

    1992-01-01

    In response to the several-fold increase in consumption of galvanized steel in the last decade and the problems associated with refurnacing larger quantities of galvanized steel scrap, a process is being developed to separate and recover the steel and zinc from galvanized ferrous scrap. The zinc is dissolved from the scrap in hot caustic using anodic assistance and is electrowon as dendritic powder. The process is effective for zinc, lead, aluminum, and cadmium removal on loose and baled scrap and on all types of galvanized steel. The process has been pilot tested for batch treatment of 1,000 tons of mostly baled scrap. A pilot plant to continuously treat loose scrap is under construction. Use of degalvanized steel scrap decreases raw materials and environmental compliance costs to steel- and iron-makers, may enable integrated steel producers to recycle furnace dusts to the sinter plant, and may enable EAF production of flat products without use of DRI or pig iron. Recycling the components of galvanized steel scrap saves primary energy, decreases zinc imports, and adds value to the scrap.

  8. A recycling process for dezincing steel scrap

    SciTech Connect

    Dudek, F.J.; Daniels, E.J.; Morgan, W.A.; Kellner, A.W.; Harrison, J.

    1992-08-01

    In response to the several-fold increase in consumption of galvanized steel in the last decade and the problems associated with refurnacing larger quantities of galvanized steel scrap, a process is being developed to separate and recover the steel and zinc from galvanized ferrous scrap. The zinc is dissolved from the scrap in hot caustic using anodic assistance and is electrowon as dendritic powder. The process is effective for zinc, lead, aluminum, and cadmium removal on loose and baled scrap and on all types of galvanized steel. The process has been pilot tested for batch treatment of 1,000 tons of mostly baled scrap. A pilot plant to continuously treat loose scrap is under construction. Use of degalvanized steel scrap decreases raw materials and environmental compliance costs to steel- and iron-makers, may enable integrated steel producers to recycle furnace dusts to the sinter plant, and may enable EAF production of flat products without use of DRI or pig iron. Recycling the components of galvanized steel scrap saves primary energy, decreases zinc imports, and adds value to the scrap.

  9. Chem I Supplement: Chemistry of Steel Making.

    ERIC Educational Resources Information Center

    Sellers, Neal

    1980-01-01

    Provides information about the chemistry of steel making applicable to teaching secondary school science. Generalized chemical reactions describe the manufacture of steel from iron ore. Also discussed are raw materials, processing choices, and how various furnaces (blast, direct reduction, open hearth, basic oxygen, electric) work. (CS)

  10. Mineral resource of the month: steel

    USGS Publications Warehouse

    Fenton, Michael D.

    2007-01-01

    About 96 million metric tons of steel was produced in the United States last year — more than any other metal. And the $3.46 billion of iron and steel scrap exported was also the highest of any metal scrap export, helping to reduce the U.S. trade deficit.

  11. African Drum and Steel Pan Ensembles.

    ERIC Educational Resources Information Center

    Sunkett, Mark E.

    2000-01-01

    Discusses how to develop both African drum and steel pan ensembles providing information on teacher preparation, instrument choice, beginning the ensemble, and lesson planning. Includes additional information for the drum ensembles. Lists references and instructional materials, sources of drums and pans, and common note layout/range for steel pan…

  12. Ellie Mannette: Master of the Steel Drum.

    ERIC Educational Resources Information Center

    Svaline, J. Marc

    2001-01-01

    Presents an interview with Elliot ("Ellie") Mannette who has played a major role in the development and application of steel drums. States that he has spent most of his life designing and teaching the steel drums. Covers interview topics and background information on Mannette. (CMK)

  13. METHOD FOR JOINING ALUMINUM TO STAINLESS STEEL

    DOEpatents

    Lemon, L.C.

    1960-05-24

    Aluminum may be joined to stainless steel without the use of flux by tinning the aluminum with a tin solder containing 1% silver and 1% lead, tinning the stainless steel with a 50% lead 50% tin solder, and then sweating the tinned surfaces together.

  14. Low Mn alloy steel for cryogenic service

    DOEpatents

    Morris, J.W. Jr.; Niikura, M.

    A ferritic cryogenic steel which has a relatively low (about 4 to 6%) manganese content and which has been made suitable for use at cryogenic temperatures by a thermal cycling treatment followed by a final tempering. The steel includes 4 to 6% manganese, 0.02 to 0.06% carbon, 0.1 to 0.4% molybdenum and 0 to 3% nickel.

  15. Forming "dynamic" membranes on stainless steel

    NASA Technical Reports Server (NTRS)

    Brandon, C. A.; Gaddis, J. L.

    1979-01-01

    "Dynamic" zirconium polyacrylic membrane is formed directly on stainless steel substrate without excessive corrosion of steel. Membrane is potentially useful in removal of contaminated chemicals from solution through reversed osmosis. Application includes use in filtration and desalination equipment, and in textile industry for separation of dyes from aqueous solvents.

  16. Hydrogen transport in iron and steel

    NASA Technical Reports Server (NTRS)

    Louthan, M. R., Jr.; Derrick, R. G.; Donovan, J. A.; Caskey, G. R., Jr.

    1976-01-01

    The permeabilities of protium, deuterium, and tritium in foil specimens of Marz grade iron, 4130 steel, Armco iron, HP-9-4-20, and T-1 steels were studied at hydrogen pressures between 0.02 and 0.5 MPa over the temperature range 260-700 K. The permeability was measured by a pressure-rise method, deuterium counting with a detector, and radioactivity counting. Good agreement is found between the measurement techniques used. It is shown that the permeabilities of protium, deuterium, and tritium in iron and T-1 steel at temperatures as low as 260 K are in good agreement with the equation proposed by Gonzalez (1967). However, the permeabilities of HP-9-4-20 and 4130 steel to hydrogen are typically lower than predicted. The isotope effect on hydrogen permeability of HP-9-4-20, 4130 and T-1 steels, and high-purity iron can be estimated by an inverse square root of mass correction.

  17. An understanding of HSLA-65 plate steels

    NASA Astrophysics Data System (ADS)

    Sampath, K.

    2006-02-01

    HSLA-65 plate steels can be produced using one of five plate manufacturing techniques: normalizing, controlled rolling (CR), controlled rolling followed by accelerated cooling (CR-AC), direct quenching and tempering (DQT), or conventional quenching and tempering (Q&T). The HSLA-65 steels are characterized by low carbon content and low alloy content, and they exhibit a low carbon equivalent that allows improved plate weldability. These characteristics in turn (a) provide the steel plate with a refined microstructure that ensures high strength and toughness; (b) eliminate or substantially reduce the need for preheating during welding; (c) resist susceptibility to hydrogen-assisted cracking (HAC) in the weld heat affected zone (HAZ) when fusion (arc) welded using low heat-input conditions; and (d) depending on section thickness, facilitate high heat-input welding (about 2 kJ/mm) without significant loss of strength or toughness in the HAZ. However, application of this plate manufacturing process and of these controls produces significant differences in the metallurgical structure and range of mechanical properties of the HSLA-65 plate steels both among themselves and versus conventional higher strength steel (HSS) plates. For example, among the HSLA-65 plate steels, those produced by Q&T exhibit minimal variability in mechanical properties, especially in thicker plates. Besides variability in mechanical properties depending on plate thickness, the CR and CR-AC plate steels exhibit a relatively higher yield strength to ultimate tensile strength (YS/UTS) ratio than do DQT and Q&T steels. Such differences in processing and properties of HSLA-65 plate steels could potentially affect the selection and control of various secondary fabrication practices, including arc welding. Consequently, fabricators must exercise extreme caution when transferring allowable limits of certified secondary fabrication practices from one type of HSLA-65 plate steel to another, even for the

  18. Automated Steel Cleanliness Analysis Tool (ASCAT)

    SciTech Connect

    Gary Casuccio; Michael Potter; Fred Schwerer; Dr. Richard J. Fruehan; Dr. Scott Story

    2005-12-30

    The objective of this study was to develop the Automated Steel Cleanliness Analysis Tool (ASCATTM) to permit steelmakers to evaluate the quality of the steel through the analysis of individual inclusions. By characterizing individual inclusions, determinations can be made as to the cleanliness of the steel. Understanding the complicating effects of inclusions in the steelmaking process and on the resulting properties of steel allows the steel producer to increase throughput, better control the process, reduce remelts, and improve the quality of the product. The ASCAT (Figure 1) is a steel-smart inclusion analysis tool developed around a customized next-generation computer controlled scanning electron microscopy (NG-CCSEM) hardware platform that permits acquisition of inclusion size and composition data at a rate never before possible in SEM-based instruments. With built-in customized ''intelligent'' software, the inclusion data is automatically sorted into clusters representing different inclusion types to define the characteristics of a particular heat (Figure 2). The ASCAT represents an innovative new tool for the collection of statistically meaningful data on inclusions, and provides a means of understanding the complicated effects of inclusions in the steel making process and on the resulting properties of steel. Research conducted by RJLG with AISI (American Iron and Steel Institute) and SMA (Steel Manufactures of America) members indicates that the ASCAT has application in high-grade bar, sheet, plate, tin products, pipes, SBQ, tire cord, welding rod, and specialty steels and alloys where control of inclusions, whether natural or engineered, are crucial to their specification for a given end-use. Example applications include castability of calcium treated steel; interstitial free (IF) degasser grade slag conditioning practice; tundish clogging and erosion minimization; degasser circulation and optimization; quality assessment/steel cleanliness; slab, billet

  19. Superstrength of nanograined steel with nanoscale intermetallic precipitates transformed from shock-compressed martensitic steel

    NASA Astrophysics Data System (ADS)

    Yu, Hailiang; Yan, Ming; Lu, Cheng; Tieu, Anh Kiet; Li, Huijun; Zhu, Qiang; Godbole, Ajit; Li, Jintao; Su, Lihong; Kong, Charlie

    2016-11-01

    An increasing number of industrial applications need superstrength steels. It is known that refined grains and nanoscale precipitates can increase strength. The hardest martensitic steel reported to date is C0.8 steel, whose nanohardness can reach 11.9 GPa through incremental interstitial solid solution strengthening. Here we report a nanograined (NG) steel dispersed with nanoscale precipitates which has an extraordinarily high hardness of 19.1 GPa. The NG steel (shock-compressed Armox 500T steel) was obtained under these conditions: high strain rate of 1.2 μs-1, high temperature rise rate of 600 Kμs-1 and high pressure of 17 GPa. The mean grain size achieved was 39 nm and reinforcing precipitates were indexed in the NG steel. The strength of the NG steel is expected to be ~3950 MPa. The discovery of the NG steel offers a general pathway for designing new advanced steel materials with exceptional hardness and excellent strength.

  20. Superstrength of nanograined steel with nanoscale intermetallic precipitates transformed from shock-compressed martensitic steel

    PubMed Central

    Yu, Hailiang; Yan, Ming; Lu, Cheng; Tieu, Anh Kiet; Li, Huijun; Zhu, Qiang; Godbole, Ajit; Li, Jintao; Su, Lihong; Kong, Charlie

    2016-01-01

    An increasing number of industrial applications need superstrength steels. It is known that refined grains and nanoscale precipitates can increase strength. The hardest martensitic steel reported to date is C0.8 steel, whose nanohardness can reach 11.9 GPa through incremental interstitial solid solution strengthening. Here we report a nanograined (NG) steel dispersed with nanoscale precipitates which has an extraordinarily high hardness of 19.1 GPa. The NG steel (shock-compressed Armox 500T steel) was obtained under these conditions: high strain rate of 1.2 μs−1, high temperature rise rate of 600 Kμs−1 and high pressure of 17 GPa. The mean grain size achieved was 39 nm and reinforcing precipitates were indexed in the NG steel. The strength of the NG steel is expected to be ~3950 MPa. The discovery of the NG steel offers a general pathway for designing new advanced steel materials with exceptional hardness and excellent strength. PMID:27892460

  1. Microstructural Characterization of Friction Stir Welded Aluminum-Steel Joints

    DTIC Science & Technology

    2013-08-01

    and around particle inclusions within the WZ. In the case of FSW aluminum to steel , the structure often seen is one of steel particles dispersed...the microstructure and mechanical performance of dissimilar FSWs between aluminum and steel , this study focuses on the characterization of the...MICROSTRUCTURAL CHARACTERIZATION OF FRICTION STIR WELDED ALUMINUM - STEEL JOINTS By ERIN ELIZABETH PATTERSON A thesis submitted in

  2. 49 CFR 192.105 - Design formula for steel pipe.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Design formula for steel pipe. 192.105 Section 192... for steel pipe. (a) The design pressure for steel pipe is determined in accordance with the following... § 192.113. T=Temperature derating factor determined in accordance with § 192.115. (b) If steel pipe...

  3. 49 CFR 178.504 - Standards for steel drums.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Standards for steel drums. 178.504 Section 178.504...-bulk Performance-Oriented Packaging Standards § 178.504 Standards for steel drums. (a) The following are identification codes for steel drums: (1) 1A1 for a non-removable head steel drum; and (2) 1A2...

  4. 46 CFR 154.195 - Aluminum cargo tank: Steel enclosure.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 5 2014-10-01 2014-10-01 false Aluminum cargo tank: Steel enclosure. 154.195 Section... Equipment Hull Structure § 154.195 Aluminum cargo tank: Steel enclosure. (a) An aluminum cargo tank and its dome must be enclosed by the vessel's hull structure or a separate steel cover. (b) The steel cover...

  5. 46 CFR 154.172 - Contiguous steel hull structure.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 5 2012-10-01 2012-10-01 false Contiguous steel hull structure. 154.172 Section 154.172... Structure § 154.172 Contiguous steel hull structure. (a) Except as allowed in paragraphs (b) and (c) of this... construction of the contiguous steel hull structure must meet the thickness and steel grade in Table 1 for...

  6. 46 CFR 154.195 - Aluminum cargo tank: Steel enclosure.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Aluminum cargo tank: Steel enclosure. 154.195 Section... Equipment Hull Structure § 154.195 Aluminum cargo tank: Steel enclosure. (a) An aluminum cargo tank and its dome must be enclosed by the vessel's hull structure or a separate steel cover. (b) The steel cover...

  7. 49 CFR 192.105 - Design formula for steel pipe.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Design formula for steel pipe. 192.105 Section 192... for steel pipe. (a) The design pressure for steel pipe is determined in accordance with the following... § 192.113. T=Temperature derating factor determined in accordance with § 192.115. (b) If steel pipe...

  8. 19 CFR 360.101 - Steel import licensing.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 19 Customs Duties 3 2012-04-01 2012-04-01 false Steel import licensing. 360.101 Section 360.101 Customs Duties INTERNATIONAL TRADE ADMINISTRATION, DEPARTMENT OF COMMERCE STEEL IMPORT MONITORING AND ANALYSIS SYSTEM § 360.101 Steel import licensing. (a) In general. (1) All imports of basic steel...

  9. 49 CFR 192.315 - Wrinkle bends in steel pipe.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Wrinkle bends in steel pipe. 192.315 Section 192... Transmission Lines and Mains § 192.315 Wrinkle bends in steel pipe. (a) A wrinkle bend may not be made on steel... wrinkle bend on steel pipe must comply with the following: (1) The bend must not have any sharp kinks....

  10. 49 CFR 178.504 - Standards for steel drums.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Standards for steel drums. 178.504 Section 178.504...-Oriented Packaging Standards § 178.504 Standards for steel drums. (a) The following are identification codes for steel drums: (1) 1A1 for a non-removable head steel drum; and (2) 1A2 for a removable...

  11. 19 CFR 360.101 - Steel import licensing.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 19 Customs Duties 3 2013-04-01 2013-04-01 false Steel import licensing. 360.101 Section 360.101 Customs Duties INTERNATIONAL TRADE ADMINISTRATION, DEPARTMENT OF COMMERCE STEEL IMPORT MONITORING AND ANALYSIS SYSTEM § 360.101 Steel import licensing. (a) In general. (1) All imports of basic steel...

  12. 46 CFR 154.195 - Aluminum cargo tank: Steel enclosure.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 5 2013-10-01 2013-10-01 false Aluminum cargo tank: Steel enclosure. 154.195 Section... Equipment Hull Structure § 154.195 Aluminum cargo tank: Steel enclosure. (a) An aluminum cargo tank and its dome must be enclosed by the vessel's hull structure or a separate steel cover. (b) The steel cover...

  13. 49 CFR 192.315 - Wrinkle bends in steel pipe.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Wrinkle bends in steel pipe. 192.315 Section 192... Transmission Lines and Mains § 192.315 Wrinkle bends in steel pipe. (a) A wrinkle bend may not be made on steel... wrinkle bend on steel pipe must comply with the following: (1) The bend must not have any sharp kinks....

  14. 49 CFR 192.105 - Design formula for steel pipe.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Design formula for steel pipe. 192.105 Section 192... for steel pipe. (a) The design pressure for steel pipe is determined in accordance with the following... § 192.113. T=Temperature derating factor determined in accordance with § 192.115. (b) If steel pipe...

  15. 49 CFR 178.504 - Standards for steel drums.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Standards for steel drums. 178.504 Section 178.504...-Oriented Packaging Standards § 178.504 Standards for steel drums. (a) The following are identification codes for steel drums: (1) 1A1 for a non-removable head steel drum; and (2) 1A2 for a removable...

  16. 19 CFR 360.101 - Steel import licensing.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 19 Customs Duties 3 2014-04-01 2014-04-01 false Steel import licensing. 360.101 Section 360.101 Customs Duties INTERNATIONAL TRADE ADMINISTRATION, DEPARTMENT OF COMMERCE STEEL IMPORT MONITORING AND ANALYSIS SYSTEM § 360.101 Steel import licensing. (a) In general. (1) All imports of basic steel...

  17. 46 CFR 154.172 - Contiguous steel hull structure.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 5 2014-10-01 2014-10-01 false Contiguous steel hull structure. 154.172 Section 154.172... Structure § 154.172 Contiguous steel hull structure. (a) Except as allowed in paragraphs (b) and (c) of this... construction of the contiguous steel hull structure must meet the thickness and steel grade in Table 1 for...

  18. 19 CFR 360.101 - Steel import licensing.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 19 Customs Duties 3 2011-04-01 2011-04-01 false Steel import licensing. 360.101 Section 360.101 Customs Duties INTERNATIONAL TRADE ADMINISTRATION, DEPARTMENT OF COMMERCE STEEL IMPORT MONITORING AND ANALYSIS SYSTEM § 360.101 Steel import licensing. (a) In general. (1) All imports of basic steel...

  19. 49 CFR 178.504 - Standards for steel drums.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Standards for steel drums. 178.504 Section 178.504...-Oriented Packaging Standards § 178.504 Standards for steel drums. (a) The following are identification codes for steel drums: (1) 1A1 for a non-removable head steel drum; and (2) 1A2 for a removable...

  20. 49 CFR 178.504 - Standards for steel drums.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Standards for steel drums. 178.504 Section 178.504...-Oriented Packaging Standards § 178.504 Standards for steel drums. (a) The following are identification codes for steel drums: (1) 1A1 for a non-removable head steel drum; and (2) 1A2 for a removable...

  1. 49 CFR 192.315 - Wrinkle bends in steel pipe.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Wrinkle bends in steel pipe. 192.315 Section 192... Transmission Lines and Mains § 192.315 Wrinkle bends in steel pipe. (a) A wrinkle bend may not be made on steel... wrinkle bend on steel pipe must comply with the following: (1) The bend must not have any sharp kinks....

  2. 49 CFR 192.105 - Design formula for steel pipe.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Design formula for steel pipe. 192.105 Section 192... for steel pipe. (a) The design pressure for steel pipe is determined in accordance with the following... § 192.113. T=Temperature derating factor determined in accordance with § 192.115. (b) If steel pipe...

  3. 75 FR 8746 - Certain Steel Grating From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-02-25

    ... COMMISSION Certain Steel Grating From China AGENCY: United States International Trade Commission. ACTION... retarded, by reason of subsidized and less-than-fair-value imports from China of certain steel gratings... ``certain steel grating, consisting of two or more pieces of steel, including load- bearing pieces and...

  4. 49 CFR 192.315 - Wrinkle bends in steel pipe.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Wrinkle bends in steel pipe. 192.315 Section 192... Transmission Lines and Mains § 192.315 Wrinkle bends in steel pipe. (a) A wrinkle bend may not be made on steel... wrinkle bend on steel pipe must comply with the following: (1) The bend must not have any sharp kinks....

  5. 46 CFR 154.172 - Contiguous steel hull structure.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Contiguous steel hull structure. 154.172 Section 154.172... Structure § 154.172 Contiguous steel hull structure. (a) Except as allowed in paragraphs (b) and (c) of this... construction of the contiguous steel hull structure must meet the thickness and steel grade in Table 1 for...

  6. 19 CFR 360.101 - Steel import licensing.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Steel import licensing. 360.101 Section 360.101 Customs Duties INTERNATIONAL TRADE ADMINISTRATION, DEPARTMENT OF COMMERCE STEEL IMPORT MONITORING AND ANALYSIS SYSTEM § 360.101 Steel import licensing. (a) In general. (1) All imports of basic steel...

  7. 46 CFR 154.195 - Aluminum cargo tank: Steel enclosure.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 5 2012-10-01 2012-10-01 false Aluminum cargo tank: Steel enclosure. 154.195 Section... Equipment Hull Structure § 154.195 Aluminum cargo tank: Steel enclosure. (a) An aluminum cargo tank and its dome must be enclosed by the vessel's hull structure or a separate steel cover. (b) The steel cover...

  8. 46 CFR 154.172 - Contiguous steel hull structure.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 5 2011-10-01 2011-10-01 false Contiguous steel hull structure. 154.172 Section 154.172... Structure § 154.172 Contiguous steel hull structure. (a) Except as allowed in paragraphs (b) and (c) of this... construction of the contiguous steel hull structure must meet the thickness and steel grade in Table 1 for...

  9. 46 CFR 154.195 - Aluminum cargo tank: Steel enclosure.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 5 2011-10-01 2011-10-01 false Aluminum cargo tank: Steel enclosure. 154.195 Section... Equipment Hull Structure § 154.195 Aluminum cargo tank: Steel enclosure. (a) An aluminum cargo tank and its dome must be enclosed by the vessel's hull structure or a separate steel cover. (b) The steel cover...

  10. 49 CFR 192.315 - Wrinkle bends in steel pipe.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Wrinkle bends in steel pipe. 192.315 Section 192... Transmission Lines and Mains § 192.315 Wrinkle bends in steel pipe. (a) A wrinkle bend may not be made on steel... wrinkle bend on steel pipe must comply with the following: (1) The bend must not have any sharp kinks....

  11. 49 CFR 192.105 - Design formula for steel pipe.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Design formula for steel pipe. 192.105 Section 192... for steel pipe. (a) The design pressure for steel pipe is determined in accordance with the following... § 192.113. T=Temperature derating factor determined in accordance with § 192.115. (b) If steel pipe...

  12. 46 CFR 154.172 - Contiguous steel hull structure.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 5 2013-10-01 2013-10-01 false Contiguous steel hull structure. 154.172 Section 154.172... Structure § 154.172 Contiguous steel hull structure. (a) Except as allowed in paragraphs (b) and (c) of this... construction of the contiguous steel hull structure must meet the thickness and steel grade in Table 1 for...

  13. Austenite grain coarsening in microalloyed steels

    NASA Astrophysics Data System (ADS)

    Cuddy, L. J.; Raley, J. C.

    1983-10-01

    A uniform, fine-grain structure is essential in steels, particularly for strip and plate, that are to meet demands for high strength and toughness. To produce such microstructures, every step of the high-temperature processing of the steel must be carefully controlled, beginning with grain coarsening that occurs during reheating for slab rolling. Extremely coarse or nonuniform grain structures in the reheated slab are difficult to refine by subsequent hot working. Accordingly, the grain-coarsening behavior of laboratory heats of C-Mn-Si base steels and of such steels with additions of Al, V, Ti, or Nb was examined to understand the principles governing the behavior of this class of steels. The grain-coarsening temperature (the temperature at which abnormal or discontinuous growth occurs) varies with the type and concentration of the microalloy addition; an approximate relation is presented. Generally the grain-coarsening temperature increases with, but is lower than, the temperature required for complete dissolution of the microalloy carbide or nitride present. Thus, steels containing the very insoluble TiN coarsen at much higher temperatures than steels containing the more soluble VCN. These results agree qualitatively with predictions of models of grain-boundary pinning by precipitate particles.

  14. Recycling galvanized steel: Operating experience and benefits

    SciTech Connect

    Dudek, F.J.; Daniels, E.J.; Morgan, W.A.

    1993-08-01

    In response to the increase in consumption of galvanized steel for automobiles in the last decade and the problems associated with remelting larger quantities of galvanized steel scrap, a process is being developed to separate and recover the steel and zinc from galvanized ferrous scrap. The zinc is dissolved from the scrap in hot caustic using anodic assistance and is recovered electrolytically as dendritic powder. The dezinced ferrous scrap is rinsed and used directly. The process is effective for zinc, lead, and aluminum removal on loose and baled scrap and on all types of galvanized steel. The process has been pilot tested for batch treatment of 900 tonnes of mostly baled scrap. A pilot plant to continuously treat loose scrap, with a design capacity of 48,000 tonnes annually, has been in operation in East Chicago, Indiana since early in 1993. The first 450 t of scrap degalvanized in the pilot plant have residual zinc below 0.01% and sodium dragout below 0.01%. Use of degalvanized steel scrap decreases raw materials, environmental compliance, and opportunity costs to steel- and iron-makers. Availability of clean degalvanized scrap may enable integrated steel producers to recycle furnace dusts to the sinter plant and EAF shops to produce flat products without use of high quality scrap alternatives such as DRI, pig iron, or iron carbide. Recycling the components of galvanized steel scrap saves primary energy, decreases zinc imports, and adds value to the scrap. The quantities of zinc available by the year 2000 from prompt and obsolete automotive scrap win approach 25% of zinc consumed in the major automotive production centers of the world. Zinc recycling from galvanized steel scrap, either before or after scrap melting, will have to be implemented.

  15. Alloy dissolution in argon stirred steel

    NASA Astrophysics Data System (ADS)

    Webber, Darryl Scott

    Alloying is required for the production of all steel products from small castings to large beams. Addition of large quantities of bulk alloys can result in alloy segregation and inconsistent alloy recovery. The objective of this research was to better understand alloy dissolution in liquid steel especially as it relates to Missouri S&Ts' patented continuous steelmaking process. A 45-kilogram capacity ladle with a single porous plug was used to evaluate the effect of four experimental factors on alloy dissolution: alloy species, alloy size or form, argon flow rate, and furnace tap temperature. Four alloys were tested experimentally including Class I low carbon ferromanganese, nickel and tin (as a surrogate for low melting alloys) and Class II ferroniobium. The alloys ranged in size and form from granular to 30 mm diameter lumps. Experimental results were evaluated using a theoretically based numerical model for the steel shell period, alloy mixing (Class I) and alloy dissolution (Class II). A CFD model of the experimental ladle was used to understand steel motion in the ladle and to provide steel velocity magnitudes for the numerical steel shell model. Experiments and modeling confirmed that smaller sized alloys have shorter steel shell periods and homogenize faster than larger particles. Increasing the argon flow rate shortened mixing times and reduced the delay between alloy addition and the first appearance of alloy in the melt. In addition, for every five degree increase in steel bath temperature the steel shell period was shortened by approximately four percent. Class II ferroniobium alloy dissolution was an order of magnitude slower than Class I alloy mixing.

  16. Steel Creek wildlife: L-Lake/Steel Creek Biological Monitoring Program, January 1986--December 1987

    SciTech Connect

    Giffin, M.A.; Patterson, K.K.

    1988-03-01

    Reptile and amphibian populations in Steel Creek below L-Lake were assessed in monthly or quarterly sampling programs. Thirty-eight species of reptiles or amphibians were collected during 1987 in the Steel Creek corridor below the L-Lake impoundment, and in the delta and channel. Juvenile turtles and alligators, and larval amphibians were observed or collected during the study, indicating continued reproduction in Steel Creek. The reptile and amphibian populations in Steel Creek show no indication of any effect due to the impoundment of the lake or the operation of L-Reactor. Waterfowl and associated birds in Steel Creek below L-Lake were observed, in conjunction with other sampling programs, during winter--spring and fall--winter migrations. Nine species of waterfowl and five species of associated birds were observed in 1987 in the Steel Creek corridor below the L-Lake impoundment and in the delta and channel.

  17. Modernization of Controls Improves Productivity and Reduces Energy Costs at a Large Steel Plant (Weirton Steel Plant)

    SciTech Connect

    2000-04-01

    In 1996 and 1997, Weirton Steel upgraded the utilities control systems at its main steel manufacturing plant in Weirton, WV. In response to increasing energy costs and the need to remain competitive in the steel industry, Weirton Steel commissioned a comprehensive energy management study of the facility, which provided the basis for an energy management control strategy.

  18. Ultrahigh Carbon Steels and Their Laminates

    DTIC Science & Technology

    1990-02-01

    PROGRAM PROJECT TASK WORK UNIT 11LitME NT NO. No. NO. NO I I TITLE tiAtluda Seca.r.ty Ck~iaialasonJ Ultrahigh Carbon Steels and their laminates...PROM Aug. 1984 To- Fe~r--9O February 1, 1906 1S. SUPPLEMENTARY NOTATION Amore coinpetc tte of tie-program is: Low Density and Tough Steels with High...Hardenabihzty: Processing, Testing and Evaluation of UHC steels and their laminates 17 COSATI CODES Is.. SUBJECT TERMS (CoAtInai" on uvwrue iroleemary

  19. Thermal embrittlement of reactor vessel steels

    SciTech Connect

    Corwin, W.R.; Nanstad, R.K.; Alexander, D.J.; Stoller, R.E.; Wang, J.A.; Odette, G.R.

    1995-06-01

    As a result of observations of possible thermal embrittlement from recent studies with welds removed from retired steam generators of the Palisades Nuclear Plant (PNP), an assessment was made of thermal aging of reactor pressure vessel (RPV) steels under nominal reactor operating conditions. Discussions are presented on (1) data from the literature regarding relatively low-temperature thermal embrittlement of RPV steels; (2)relevant data from the US power reactor-embrittlement data base (PR-EDB); and (3)potential mechanisms of thermal embrittlement in low-alloy steels.

  20. Direct Alloying of Steel with Nickel Concentrate

    NASA Astrophysics Data System (ADS)

    Nokhrina, O. I.; Rozhikhina, I. D.; Proshunin, I. E.

    2016-08-01

    A technology of alloying steel with nickel reduced from nickel concentrate is analysed and developed. Limits of reduction concentration areas are defined. An optimal composition of nickel concentrate pellets and a method of feeding them into the furnace are deduced from experiments. It is proved that when pellets made of nickel concentrate and coke are added into the charge during steel smelting by the technology of alloyed scrap remelting, nickel recovery achieves 92-95%. The technology was tested by smelting DSP-40 steel.

  1. Strain hardening of steel EP836

    SciTech Connect

    Lyadskaya, A.A.; Lappa, R.M.; Spuskanyuk, V.Z.

    1986-03-01

    The authors investigate the effect of different combinations of cold hydraulic pressing and heat treatment on the physical and mechanical properties of steel EP836 (03N17K10V10MT), containing 0.03% C, 16-17% Ni, 10-11.5% Co, 9.5-11.5% W, 1% Ti, 1% Mo, and 0.15% A1. Deformation of the unaged steel resulted in insignificant hardening without a decrease in plasticity; this agrees with the results of investigations of other steels of this class.

  2. Tritiated Water Interaction with Stainless Steel

    SciTech Connect

    Glen R. Longhurst

    2007-05-01

    Experiments conducted to study tritium permeation of stainless steel at ambient and elevated temperatures revealed that HT converts relatively quickly to HTO. Further, the HTO partial pressure contributes essentially equally with elemental tritium gas in driving permeation through the stainless steel. Such permeation appears to be due to dissociation of the water molecule on the hot stainless steel surface. There is an equilibrium concentration of HTO vapor above adsorbed gas on the walls of the experimental apparatus evident from freezing transients. The uptake process of tritium from the carrier gas involves both surface adsorption and isotopic exchange with surface bound water.

  3. Ultrasonic attenuation in pearlitic steel.

    PubMed

    Du, Hualong; Turner, Joseph A

    2014-03-01

    Expressions for the attenuation coefficients of longitudinal and transverse ultrasonic waves are developed for steel with pearlitic microstructure. This type of lamellar duplex microstructure influences attenuation because of the lamellar spacing. In addition, longitudinal attenuation measurements were conducted using an unfocused transducer with 10 MHz central frequency on the cross section of a quenched railroad wheel sample. The dependence of longitudinal attenuation on the pearlite microstructure is observed from the changes of longitudinal attenuation from the quenched tread surface to deeper locations. The results show that the attenuation value is lowest and relatively constant within the quench depth, then increases linearly. The experimental results demonstrate a reasonable agreement with results from the theoretical model. Ultrasonic attenuation provides an important non-destructive method to evaluate duplex microstructure within grains which can be implemented for quality control in conjunction with other manufacturing processes.

  4. Microstructural characterization in dissimilar friction stir welding between 304 stainless steel and st37 steel

    SciTech Connect

    Jafarzadegan, M.; Feng, A.H.; Abdollah-zadeh, A.; Saeid, T.; Shen, J.; Assadi, H.

    2012-12-15

    In the present study, 3 mm-thick plates of 304 stainless steel and st37 steel were welded together by friction stir welding at a welding speed of 50 mm/min and tool rotational speed of 400 and 800 rpm. X-ray diffraction test was carried out to study the phases which might be formed in the welds. Metallographic examinations, and tensile and microhardness tests were used to analyze the microstructure and mechanical properties of the joint. Four different zones were found in the weld area except the base metals. In the stir zone of the 304 stainless steel, a refined grain structure with some features of dynamic recrystallization was evidenced. A thermomechanically-affected zone was characterized on the 304 steel side with features of dynamic recovery. In the other side of the stir zone, the hot deformation of the st37 steel in the austenite region produced small austenite grains and these grains transformed to fine ferrite and pearlite and some products of displacive transformations such as Widmanstatten ferrite and martensite by cooling the material after friction stir welding. The heat-affected zone in the st37 steel side showed partially and fully refined microstructures like fusion welding processes. The recrystallization in the 304 steel and the transformations in the st37 steel enhanced the hardness of the weld area and therefore, improved the tensile properties of the joint. - Highlights: Black-Right-Pointing-Pointer FSW produced sound welds between st37 low carbon steel and 304 stainless steel. Black-Right-Pointing-Pointer The SZ of the st37 steel contained some products of allotropic transformation. Black-Right-Pointing-Pointer The material in the SZ of the 304 steel showed features of dynamic recrystallization. Black-Right-Pointing-Pointer The finer microstructure in the SZ increased the hardness and tensile strength.

  5. Chemical state of nitrogen in a high nitrogen face-centered-cubic phase formed on plasma source ion nitrided austenitic stainless steel

    SciTech Connect

    Lei, M.K.; Zhu, X.M.

    2004-09-01

    A single high nitrogen face-centered-cubic phase ({gamma}{sub N}) was formed on the plasma source ion nitrided 1Cr18Ni9Ti (18-8 type) austenitic stainless steel. Auger electron spectroscopy and x-ray photoelectron spectroscopy, in conjunction with ion beam sputtering, were used to determine the chemical composition and bonding of nitrogen in the {gamma}{sub N} phase. The chemical composition of the {gamma}{sub N} phase was shown as a formula with atomic fraction (Fe{sub 0.60},Cr{sub 0.22},Ni{sub 0.18}){sub 2}N. The {gamma}{sub N} phase possessed weaker Cr-N ionic-type bonds and stronger Fe-N ionic-type bonds, compared with the stoichiometric nitrides. The Cr 2p{sub 3sol2} binding energy was 1.1 eV lower than that of CrN and Cr{sub 2}N phases (at 575.5 eV). The chemical shift of the Fe-N bonding compared with the Fe-Fe bonding was nearly 2.1 eV. The N 1s binding energies showed that the nitrogen was in the chemical state with iron (at 396.6 eV) and chromium (at 397.7 eV). All the chromium appeared to be in the Cr-N bond. A part of iron was also observed in the nitride state, and all the nickel was contained in the metallic state.

  6. Evaluation of Direct Diode Laser Deposited Stainless Steel 316L on 4340 Steel Substrate for Aircraft Landing Gear Application

    DTIC Science & Technology

    2010-03-01

    AFRL-RX-WP-TP-2010-4149 EVALUATION OF DIRECT DIODE LASER DEPOSITED STAINLESS STEEL 316L ON 4340 STEEL SUBSTRATE FOR AIRCRAFT LANDING GEAR...March 2010 – 01 March 2010 4. TITLE AND SUBTITLE EVALUATION OF DIRECT DIODE LASER DEPOSITED STAINLESS STEEL 316L ON 4340 STEEL SUBSTRATE FOR...Code) N/A Standard Form 298 (Rev. 8-98) Prescribed by ANSI Std. Z39-18 Evaluation of Direct Diode Laser Deposited Stainless Steel 316L on

  7. TiC reinforced cast chromium steels

    SciTech Connect

    Dogan, Omer N.; Rawers, James C.; Hawk, Jeffrey A.; Schrems, Karol K.

    2003-11-01

    A series of new titanium carbide reinforced cast chromium steels were developed for wear applications. Objective of the program was to enhance wear resistant alloys and, if possible, improve mechanical properties. The new steels which were melted in a vacuum induction furnace contained 12 Cr, 3-5 Ti, 1-2 C in weight percent. Alloying with Ti changed the precipitate microstructure from Cr carbide to TiC dispersed in a martensitic matrix. Yield strength and impact resistance improved with Ti alloying. Wear rates of the cast Cr/TiC steels, (determined from high- and low-stress abrasion tests, erosion test, and scratch tests) were generally lower than both the as-cast and heat-treated AISI type 440°C steel and were often further reduced by increasing the Ti alloy concentration. The exceptions were the erosion test for which all materials had similar wear rate.

  8. TiC reinforced cast Cr steels

    SciTech Connect

    Dogan, O.N.; Hawk, J.A.; Schrems, K.K.

    2006-06-01

    A new class of materials, namely TiC-reinforced cast chromium (Cr) steels, was developed for applications requiring high abrasion resistance and good fracture toughness. The research approach was to modify the carbide structure of commercial AISI 440C steel for better fracture resistance while maintaining the already high abrasion resistance. The new alloys contained 12Cr, 2.5–4.5Ti, and 1–1.5C (wt.%) and were melted in a vacuum induction furnace. Their microstructure was composed primarily of a martensitic matrix with a dispersion of TiC precipitates. Modification of TiC morphology was accomplished through changing the cooling rate during solidification. Wear rates of the TiC-reinforced Cr steels were comparable to that of AISI 440C steel, but the impact resistance was much improved.

  9. Steel - Structural, reinforcing; Pressure vessel, railway

    SciTech Connect

    Not Available

    1986-01-01

    This book contains specifications for structural steel used in various constructions; concrete reinforcement; plate and forgings for boilers and pressure vesseles; rails, axles, wheels and other accessories for railway service.

  10. High performance corrosion-resistant structural steels

    SciTech Connect

    Fletcher, F.B.; Ferry, B.N.; Beblo, D.G.

    1995-12-31

    A new corrosion-resistant structural steel named Duracorr was developed for low maintenance when compared to conventional structural steels. The new stainless steel is a dual phase composition between the established 12% Cr, ferritic T409 and martensitic T410 grades. Attractive combinations of hardness, strength, toughness, weldability and formability are derived from a microstructure that is a dual phase mixture of ferrite and martensite. The Duracorr composition, UNS S41003, provides for a microstructure of ferrite and austenite to be present throughout the hot rolling process. Cooling to room temperature causes transformation of the austenite to martensite. Subsequent tempering of the steel creates minimum mechanical properties of 275 MPa (40 ksi) yield strength and 455 MPa (66 ksi) tensile strength with room temperature longitudinal Charpy impact values typically greater than 34 J (25 ft-lbs).

  11. Lightweight Steel Solutions for Automotive Industry

    SciTech Connect

    Lee, Hong Woo; Kim, Gyosung; Park, Sung Ho

    2010-06-15

    Recently, improvement in fuel efficiency and safety has become the biggest issue in worldwide automotive industry. Although the regulation of environment and safety has been tightened up more and more, the majority of vehicle bodies are still manufactured from stamped steel components. This means that the optimized steel solutions enable to demonstrate its ability to reduce body weight with high crashworthiness performance instead of expensive light weight materials such as Al, Mg and composites. To provide the innovative steel solutions for automotive industry, POSCO has developed AHSS and its application technologies, which is directly connected to EVI activities. EVI is a technical cooperation program with customer covering all stages of new car project from design to mass production. Integrated light weight solutions through new forming technologies such as TWB, hydroforming and HPF are continuously developed and provided for EVI activities. This paper will discuss the detailed status of these technologies especially light weight steel solutions based on innovative technologies.

  12. Abbreviated annealing of high-speed steel

    SciTech Connect

    Zablotskii, V.K.; Bartel, G.P.

    1987-07-01

    The authors investigate the structural and phase transformations during the heating, holding, and cooling of high-speed steels of two basic groups: tungsten (R18, R12, R12F3, and R12F4K5) and tungsten-molybdenum (R6M5, 10R6M5, R6M5K5, R8M3, 10R8M3, and R8M3K6S) steels in the forged state. They propose a cooling regime with complete alpha-gamma recrystallization whose implementation at a Soviet steel plant has made it possible to reduce the duration of heat treatment and increase productivity by 20% in cutting the annealed high-speed steels.

  13. Clean Cast Steel Technology, Phase IV

    SciTech Connect

    Charles E. Bates

    2003-02-24

    The objective of the Clean Cast Steel Technology Program was to improve casting product quality by removing or minimizing oxide defects and to allow the production of higher integrity castings for high speed machining lines. Previous research has concentrated on macro-inclusions that break, chip, or crack machine tool cutters and drills and cause immediate shutdown of the machining lines. The overall goal of the project is to reduce the amount of surface macro-inclusions and improve the machinability of steel castings. Macro-inclusions and improve the machinability of steel castings. Macro-inclusions have been identified by industrial sponsors as a major barrier to improving the quality and marketability of steel castings.

  14. Precise carbon control of fabricated stainless steel

    DOEpatents

    Nilsen, R.J.

    1975-12-01

    A process is described for controlling the carbon content of fabricated stainless steel components including the steps of heat treating the component in hydrogen atmospheres of varying dewpoints and carbon potentials.

  15. Stainless Steel to Titanium Bimetallic Transitions

    SciTech Connect

    Kaluzny, J. A.; Grimm, C.; Passarelli, D.

    2015-01-01

    In order to use stainless steel piping in an LCLS-II (Linac Coherent Light Source Upgrade) cryomodule, stainless steel to titanium bimetallic transitions are needed to connect the stainless steel piping to the titanium cavity helium vessel. Explosion bonded stainless steel to titanium transition pieces and bimetallic transition material samples have been tested. A sample transition tube was subjected to tests and x-ray examinations between tests. Samples of the bonded joint material were impact and tensile tested at room temperature as well as liquid helium temperature. The joint has been used successfully in horizontal tests of LCLS-II cavity helium vessels and is planned to be used in LCLS-II cryomodules. Results of material sample and transition tube tests will be presented.

  16. Lightweight Steel Solutions for Automotive Industry

    NASA Astrophysics Data System (ADS)

    Lee, Hong Woo; Kim, Gyosung; Park, Sung Ho

    2010-06-01

    Recently, improvement in fuel efficiency and safety has become the biggest issue in worldwide automotive industry. Although the regulation of environment and safety has been tightened up more and more, the majority of vehicle bodies are still manufactured from stamped steel components. This means that the optimized steel solutions enable to demonstrate its ability to reduce body weight with high crashworthiness performance instead of expensive light weight materials such as Al, Mg and composites. To provide the innovative steel solutions for automotive industry, POSCO has developed AHSS and its application technologies, which is directly connected to EVI activities. EVI is a technical cooperation program with customer covering all stages of new car project from design to mass production. Integrated light weight solutions through new forming technologies such as TWB, hydroforming and HPF are continuously developed and provided for EVI activities. This paper will discuss the detailed status of these technologies especially light weight steel solutions based on innovative technologies.

  17. Hydrogen compatibility handbook for stainless steels

    SciTech Connect

    Caskey, G.R. Jr.

    1983-06-01

    This handbook compiles data on the effects of hydrogen on the mechanical properties of stainless steels and discusses this data within the context of current understanding of hydrogen compatibility of metals. All of the tabulated data derives from continuing studies of hydrogen effects on materials that have been conducted at the Savannah River Laboratory over the past fifteen years. Supplementary data from other sources are included in the discussion. Austenitic, ferritic, martensitic, and precipitation hardenable stainless steels have been studied. Damage caused by helium generated from decay of tritium is a distinctive effect that occurs in addition to the hydrogen isotopes protium and deuterium. The handbook defines the scope of our current knowledge of hydrogen effects in stainless steels and serves as a guide to selection of stainless steels for service in hydrogen.

  18. Ion-beam nitriding of steels

    NASA Technical Reports Server (NTRS)

    Salik, J.

    1984-01-01

    The application of the ion beam technique to the nitriding of steels is described. It is indicated that the technique can be successfully applied to nitriding. Some of the structural changes obtained by this technique are similar to those obtained by ion nitriding. The main difference is the absence of the iron nitride diffraction lines. It is found that the dependence of the resultant microhardness on beam voltage for super nitralloy is different from that of 304 stainless steel.

  19. Thermal treatment of dissimilar steels' welded joints

    NASA Astrophysics Data System (ADS)

    Nikulina, A. A.; Denisova, A. S.; Gradusov, I. N.; Ryabinkina, P. A.; Rushkovets, M. V.

    2016-04-01

    In this paper combinations of chrome-nickel steel and high-carbon steel, produced by flash butt welding after heat treatment, are investigated. Light and electron microscopic studies show that the welded joints after heat treatment have a complex structure consisting of several phases as initial welded joints. A martensite structure in welded joints after thermal treatment at 300... 800 °C has been found.

  20. High strength and high toughness steel

    DOEpatents

    Parker, Earl R.; Zackay, Victor F.

    1979-01-01

    A structural steel which possess both high strength and high toughness and has particular application of cryogenic uses. The steel is produced by the utilization of thermally induced phase transformation following heating in a three-phase field in iron-rich alloys of the Fe-Ni-Ti system, with a preferred composition of 12% nickel, 0.5% titanium, the remainder being iron.

  1. High strength, high ductility low carbon steel

    DOEpatents

    Koo, Jayoung; Thomas, Gareth

    1978-01-01

    A high strength, high ductility low carbon steel consisting essentially of iron, 0.05-0.15 wt% carbon, and 1-3 wt% silicon. Minor amounts of other constituents may be present. The steel is characterized by a duplex ferrite-martensite microstructure in a fibrous morphology. The microstructure is developed by heat treatment consisting of initial austenitizing treatment followed by annealing in the (.alpha. + .gamma.) range with intermediate quenching.

  2. Stainless Steels’ Resistance to Hydroerosion,

    DTIC Science & Technology

    1980-07-30

    Omel’chenko, engineer, S. L. Millichenko, A. G. Aleksandrov, Candidates of Technical Sciences Thanks to a high corrosion resistance stainless steels have...has great significance. The resistance to hydroerosion of several of the most common types of stainless steels which have roughly the same corrosion ...the failure is first localized in the ferrite phase and occurs by means of plastic deformation and the development of fatigue micro- cracks both

  3. Diffraction Measurements on CPF Steel Fatigue Samples

    DTIC Science & Technology

    1995-05-30

    I I I I I I I I I I I I I I I I I I I - 535 - Diffraction Measurements on CPF Steel Fatigue Samples by Percy Clark*, Tom...to the formation of a detectable fatigue crack, a series of hourglass shaped specimens were fabricated from 350WT steel , cyclically loaded to...were made between these experiments and earlier less successful similar experiments conducted on HY80 samples. The limitations and potential for the

  4. Occupational rhinitis due to steel welding fumes.

    PubMed

    Castano, Roberto; Suarthana, Eva

    2014-12-01

    Exposure to welding fumes is a recognized respiratory hazard. Occupational asthma but not occupational rhinitis has been documented in workers exposed to steel welding fumes. We report a 26-year-old male with work-related rhinitis symptoms as well as lower airways symptoms suggestive of occupational asthma and metal fume fever associated with exposure to steel welding fumes. The diagnosis of occupational rhinitis was confirmed by specific inhalation challenge.

  5. Ion-beam nitriding of steels

    NASA Technical Reports Server (NTRS)

    Salik, J.

    1985-01-01

    The application of the ion beam technique to the nitriding of steels is described. It is indicated that the technique can be successfully applied to nitriding. Some of the structural changes obtained by this technique are similar to those obtained by ion nitriding. The main difference is the absence of the iron nitride diffraction lines. It is found that the dependence of the resultant microhardness on beam voltage for super nitralloy is different from that of 304 stainless steel.

  6. Improved High Strength Armor Steel through Texturing

    DTIC Science & Technology

    1979-09-01

    80 I 14 02w INTRODUCTION During metal manufacturing processing, such as rolling of sheet and plate, the polycrystalline aggregate of the material...of the quenched martensite has been documented by previous investigators including Kula and Dhosi who ob- served that thermomechanical processing can...textured armor steel exhibits improved ballistic resistance to conventionally uncontrolled rolled steels of equal hardness at normal obliquity. This

  7. Laser Rewelding of 304L Stainless Steel.

    SciTech Connect

    Maguire, Michael Christopher; Rodelas, Jeffrey

    2016-11-01

    Laser welding of 304L stainless steel during component fabrication has been found to alter the chemical composition of the steel due to material evaporation. During repair or rework, or during potential reuse/ rewelding of certain components, the potential exists to alter the composition to the extent that the material becomes prone to solidification cracking. This work aims to characterize the extent of this susceptibility in order to make informed decisions regarding rewelding practice and base metal chemistry allowances.

  8. Regularities of bainitic steel deformation transition

    NASA Astrophysics Data System (ADS)

    Gromov, V. E.; Nikitina, E. N.; Ivanov, Yu F.; Aksenova, K. V.

    2016-09-01

    Quantitative analysis of defect and carbide subsystems evolution in medium-carbon bainitic steel subjected to compressive strain up to 36% was performed by means of transmission electron diffraction microscopy. Dislocation substructure and carbide phase parameters dependence on degree of deformation are identified, possible reasons of staging in their changes are discussed. It is suggested that the reason for bainitic steel softening at high (over 15%) degrees of deformation is activation of deformation microtwinning process.

  9. Stainless steel recycle FY94 progress report

    SciTech Connect

    Imrich, K.J.

    1994-10-28

    The Materials Technology Section (MTS) of the Savannah River Technology Center (SRTC) was asked to demonstrate the practicality of recycling previously contaminated stainless steel components such as reactor heat exchanger heads, process water piping and slug buckets into 208 liters (55 gallon) drums and 2.8 cubic meter (100 ft{sup 3}) storage boxes. Radioactively contaminated stainless steel scrap will be sent to several industrial partners where it will be melted, decontaminated/cast into ingots, and rolled into plate and sheet and fabricated into the drums and boxes. As part of this recycle initiative, MTS was requested to demonstrate that radioactively contaminated Type 304L stainless steel could be remelted and cast to meet the applicable ASTM specification for fabrication of drums and boxes. In addition, MTS was requested to develop the technical basis of melt decontamination and establish practicality of using this approach for value added products. The findings presented in this investigation lead to the following conclusions: recycle of 18 wt% Cr-8 wt% Ni alloy can be achieved by melting Type 304 stainless steel in a air vacuum induction furnace; limited melt decontamination of the contaminated stainless steel was achieved, surface contamination was removed by standard decontamination techniques; carbon uptake in the as-cast ingots resulted from the graphite susceptor used in this experiment and is unavoidable with this furnace configuration. A new furnace optimized for melting stainless steel has been installed and is currently being tested for use in this program.

  10. Steels with controlled hardenability for induction hardening

    NASA Astrophysics Data System (ADS)

    Shepelyakovskii, K. Z.

    1980-07-01

    Steels of the CH and LH type developed in the Soviet Union permit the use of a new method of induction hardening — bulk-surface hardening — and efficient utilization of the high-strength conditions (σb = 230-250 kgf/mm2). These steels make it possible to improve the structural strength, operating characteristics, service life, and reliability of critical heavily loaded machine parts. At the same time, CH steels make it possible to reduce by a factor of 2-3 the quantity of alloying elements, reduce the electrical energy for heat treatment, and completely exclude the cost of quenching oil for heat treatment in automatic equipment with high labor productivity, while retaining good working conditions. All this leads to substantial savings in production and operation. For example, when transmission gears (cylindrical and conical) are manufactured from LH steels the annual savings amount to more than 700,000 rubles at two automobile plants. Machine parts of CH steels — half axles and bearings in railway cars —have saved respectively six and four million rubles annually. The introduction of controlled-hardenability steels for induction hardening is a necessary condition for technological progress in machine construction and metallurgy.

  11. Development of Steel Foam Materials and Structures

    SciTech Connect

    Kenneth Kremer; Anthony Liszkiewicz; James Adkins

    2004-10-20

    In the past few years there has been a growing interest in lightweight metal foams. Demands for weight reduction, improved fuel efficiency, and increased passenger safety in automobiles now has manufacturers seriously considering the use of metal foams, in contrast to a few years ago, when the same materials would have been ruled out for technical or economical reasons. The objective of this program was to advance the development and use of steel foam materials, by demonstrating the advantages of these novel lightweight materials in selected generic applications. Progress was made in defining materials and process parameters; characterization of physical and mechanical properties; and fabrication and testing of generic steel foam-filled shapes with compositions from 2.5 wt.% to 0.7 wt.% carbon. A means of producing steel foam shapes with uniform long range porosity levels of 50 to 60 percent was demonstrated and verified with NDE methods. Steel foam integrated beams, cylinders and plates were mechanically tested and demonstrated advantages in bend stiffness, bend resistance, and crush energy absorption. Methods of joining by welding, adhesive bonding, and mechanical fastening were investigated. It is important to keep in mind that steel foam is a conventional material in an unconventional form. A substantial amount of physical and mechanical properties are presented throughout the report and in a properties database at the end of the report to support designer's in applying steel foam in unconventional ways.

  12. Ultrahigh Ductility, High-Carbon Martensitic Steel

    NASA Astrophysics Data System (ADS)

    Qin, Shengwei; Liu, Yu; Hao, Qingguo; Zuo, Xunwei; Rong, Yonghua; Chen, Nailu

    2016-10-01

    Based on the proposed design idea of the anti-transformation-induced plasticity effect, both the additions of the Nb element and pretreatment of the normalization process as a novel quenching-partitioning-tempering (Q-P-T) were designed for Fe-0.63C-1.52Mn-1.49Si-0.62Cr-0.036Nb hot-rolled steel. This high-carbon Q-P-T martensitic steel exhibits a tensile strength of 1890 MPa and elongation of 29 pct accompanied by the excellent product of tensile and elongation of 55 GPa pct. The origin of ultrahigh ductility for high-carbon Q-P-T martensitic steel is revealed from two aspects: one is the softening of martensitic matrix due to both the depletion of carbon in the matensitic matrix during the Q-P-T process by partitioning of carbon from supersaturated martensite to retained austenite and the reduction of the dislocation density in a martensitic matrix by dislocation absorption by retained austenite effect during deformation, which significantly enhances the deformation ability of martensitic matrix; another is the high mechanical stability of considerable carbon-enriched retained austenite, which effectively reduces the formation of brittle twin-type martensite. This work verifies the correctness of the design idea of the anti-TRIP effect and makes the third-generation advanced high-strength steels extend to the field of high-carbon steels from low- and medium-carbon steels.

  13. Microstructural studies of advanced austenitic steels

    SciTech Connect

    Todd, J. A.; Ren, Jyh-Ching

    1989-11-15

    This report presents the first complete microstructural and analytical electron microscopy study of Alloy AX5, one of a series of advanced austenitic steels developed by Maziasz and co-workers at Oak Ridge National Laboratory, for their potential application as reheater and superheater materials in power plants that will reach the end of their design lives in the 1990's. The advanced steels are modified with carbide forming elements such as titanium, niobium and vanadium. When combined with optimized thermo-mechanical treatments, the advanced steels exhibit significantly improved creep rupture properties compared to commercially available 316 stainless steels, 17--14 Cu--Mo and 800 H steels. The importance of microstructure in controlling these improvements has been demonstrated for selected alloys, using stress relaxation testing as an accelerated test method. The microstructural features responsible for the improved creep strengths have been identified by studying the thermal aging kinetics of one of the 16Ni--14Cr advanced steels, Alloy AX5, in both the solution annealed and the solution annealed plus cold worked conditions. Time-temperature-precipitation diagrams have been developed for the temperature range 600 C to 900 C and for times from 1 h to 3000 h. 226 refs., 88 figs., 10 tabs.

  14. Ion-nitriding of austenitic stainless steels

    SciTech Connect

    Pacheco, O.; Hertz, D.; Lebrun, J.P.; Michel, H.

    1995-12-31

    Although ion-nitriding is an extensively industrialized process enabling steel surfaces to be hardened by nitrogen diffusion, with a resulting increase in wear, seizure and fatigue resistance, its direct application to stainless steels, while enhancing their mechanical properties, also causes a marked degradation in their oxidation resistance. However, by adaption of the nitriding process, it is possible to maintain the improved wear resistant properties while retaining the oxidation resistance of the stainless steel. The controlled diffusion permits the growth of a nitrogen supersaturated austenite layer on parts made of stainless steel (AISI 304L and 316L) without chromium nitride precipitation. The diffusion layer remains stable during post heat treatments up to 650 F for 5,000 hrs and maintains a hardness of 900 HV. A very low and stable friction coefficient is achieved which provides good wear resistance against stainless steels under diverse conditions. Electrochemical and chemical tests in various media confirm the preservation of the stainless steel characteristics. An example of the application of this process is the treatment of Reactor Control Rod Cluster Assemblies (RCCAs) for Pressurized Water Nuclear Reactors.

  15. Effects of interactive particles on steel weldability

    SciTech Connect

    Eijk, C. van der; Grong, O.; Babu, S.S.; David, S.A.

    1998-11-01

    The concept of intragranular ferrite nucleation by specific inclusions is well known from steel weld metals. In this paper it is shown that the idea can be transferred to steel metallurgy. Control of the inclusion composition and thus the nucleation potency with respect to ferrite can readily be achieved by the choice of an appropriate deoxidation procedure. Thermodynamic (Thermo-Calc) calculations in addition to X-ray mappings and microprobe analysis are employed to understand and predict the inclusion formation in the steels. Three different steels, two of them Ti-deoxidized, and one Al-Ca-deoxidized, have been subjected to weld thermal simulation at different peak temperatures and cooling programs followed by Charpy-V notch testing at {minus}40 C to reveal differences in the HAZ toughness. The results from these tests show that the titanium deoxidized steels exhibit excellent toughness in the grain coarsened HAZ after high heat input weld simulation because of a refinement of the microstructure. This observation is in contrast to the more traditional behavior of the conventional Al-Ca deoxidized steels, which show no evidence of intragranular ferrite formation.

  16. Utilization of structural steel in buildings

    PubMed Central

    Moynihan, Muiris C.; Allwood, Julian M.

    2014-01-01

    Over one-quarter of steel produced annually is used in the construction of buildings. Making this steel causes carbon dioxide emissions, which climate change experts recommend be reduced by half in the next 37 years. One option to achieve this is to design and build more efficiently, still delivering the same service from buildings but using less steel to do so. To estimate how much steel could be saved from this option, 23 steel-framed building designs are studied, sourced from leading UK engineering firms. The utilization of each beam is found and buildings are analysed to find patterns. The results for over 10 000 beams show that average utilization is below 50% of their capacity. The primary reason for this low value is ‘rationalization’—providing extra material to reduce labour costs. By designing for minimum material rather than minimum cost, steel use in buildings could be drastically reduced, leading to an equivalent reduction in ‘embodied’ carbon emissions. PMID:25104911

  17. Demonstrating Nonhexavelent Chrome Steel Conversion Coatings on Stryker High Hard Armor Steel Hatches

    DTIC Science & Technology

    2014-01-01

    protection against armor-piercing threats, these steels corrode rapidly without the use of a good corrosion protective coating ...stress corrosion cracking. • Provides a more robust process that will protect against deficiencies in the inorganic coating process. Advantages...of other systems provide good protection against armor-piercing threats. However, these steels corrode rapidly without good corrosion protective

  18. A Computational Analysis of a Shear Punch Test

    DTIC Science & Technology

    2009-08-01

    were 1.27cm diameter 350- maraging steel . The incident and output bars were 150cm in length, while the striker bar was available in 25, 50, and...yield [MPa] En [MPa] Maraging steel 199 0.33 2242 0.00 Stainless steel 200 0.33 1170 100 (b) Johnson-Cook Model A [MPa] B [MPa...pulse. The specimen holder was made from 17- 4 PH stainless steel and consisted of three pieces held together with six high- strength bolts. In

  19. EMPLACEMENT DRIFT INVERT-LOW STEEL EVALUATION

    SciTech Connect

    M. E. Taylor and D. H. Tang

    2000-09-29

    This technical report evaluates and develops options for reducing the amount of steel in the emplacement drift invert. Concepts developed in the ''Invert Configuration and Drip Shield Interface'' were evaluated to determine material properties required for the proposed invert concepts. Project requirements documents prescribe the use of a carbon steel frame for the invert with a granular material of crushed tuff as ballast. The ''Invert Configuration and Drip Shield Interface'' developed three concepts: (1) All-Ballast Invert; (2) Modified Steel Invert with Ballast; and (3) Steel Tie with Ballast Invert. Analysis of the steel frame members, runway beams, and guide beams, for the modified steel invert with ballast, decreased the quantity of steel in the emplacement drift invert, however a substantial steel support frame for the gantry and waste package/pallet assembly is still required. Use of one of the other two concepts appears to be an alternative to the steel frame and each of the concepts uses considerably less steel materials. Analysis of the steel tie with ballast invert shows that the bearing pressure on the ballast under the single steel tie, C 9 x 20, loaded with the waste package/pallet assembly, drip shield, and backfill exceeds the upper bound of the allowable bearing capacity for tuff used in this study. The single tie, C 10 x 20, will also fail for the same loading condition except for the tie length of 4.2 meters and longer. Analysis also shows that with two ties, C 9 or 10 x 20's, the average ballast pressure is less than the allowable bearing capacity. Distributing the waste package/pallet, drip shield, and backfill loads to two steel ties reduces the contact bearing pressure. Modifying the emplacement pallet end beams to a greater width, reducing the tie spacing, and increasing the width of the ties would ensure that the pallet beams are always supported by two steel ties. Further analysis is required to determine compatible tie size and spacing

  20. 76 FR 33239 - High Pressure Steel Cylinders From the People's Republic of China; Initiation of Countervailing...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-08

    ... International Trade Administration High Pressure Steel Cylinders From the People's Republic of China; Initiation...'') petition concerning imports of high pressure steel cylinders (``steel cylinders'') from the People's... Petitions for the Imposition of Antidumping and Countervailing Duties Against High Pressure Steel...

  1. 77 FR 37384 - High Pressure Steel Cylinders From the People's Republic of China: Countervailing Duty Order

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-06-21

    ... International Trade Administration High Pressure Steel Cylinders From the People's Republic of China... duty order on high pressure steel cylinders (``steel cylinders'') from the People's Republic of China.... See High Pressure Steel Cylinders From the People's Republic of China: Final...

  2. High Mn austenitic stainless steel

    DOEpatents

    Yamamoto, Yukinori [Oak Ridge, TN; Santella, Michael L [Knoxville, TN; Brady, Michael P [Oak Ridge, TN; Maziasz, Philip J [Oak Ridge, TN; Liu, Chain-tsuan [Knoxville, TN

    2010-07-13

    An austenitic stainless steel alloy includes, in weight percent: >4 to 15 Mn; 8 to 15 Ni; 14 to 16 Cr; 2.4 to 3 Al; 0.4 to 1 total of at least one of Nb and Ta; 0.05 to 0.2 C; 0.01 to 0.02 B; no more than 0.3 of combined Ti+V; up to 3 Mo; up to 3 Co; up to 1W; up to 3 Cu; up to 1 Si; up to 0.05 P; up to 1 total of at least one of Y, La, Ce, Hf, and Zr; less than 0.05 N; and base Fe, wherein the weight percent Fe is greater than the weight percent Ni, and wherein the alloy forms an external continuous scale including alumina, nanometer scale sized particles distributed throughout the microstructure, the particles including at least one of NbC and TaC, and a stable essentially single phase FCC austenitic matrix microstructure that is essentially delta-ferrite-free and essentially BCC-phase-free.

  3. Mechanical properties of irradiated 9Cr-2WVTa steel

    SciTech Connect

    Klueh, R.L.; Alexander, D.J.; Rieth, M.

    1998-09-01

    An Fe-9Cr-2W-0.25V-0.07Ta-0.1C (9Cr-2WVTa) steel has excellent strength and impact toughness before and after irradiation in the Fast Flux Test Facility and the High Flux Reactor (HFR). The ductile-brittle transition temperature (DBTT) increased only 32 C after 28 dpa at 365 C in FFTF, compared to a shift of {approx}60 C for a 9Cr-2WV steel--the same as the 9Cr-2WVTa steel but without tantalum. This difference occurred despite the two steels having similar tensile but without tantalum. This difference occurred despite the two steels having similar tensile properties before and after irradiation. The 9Cr-2WVTa steel has a smaller prior-austenite grain size, but otherwise microstructures are similar before irradiation and show similar changes during irradiation. The irradiation behavior of the 9Cr-2WVTa steel differs from the 9Cr-2WV steel and other similar steels in two ways: (1) the shift in DBTT of the 9Cr-2WVTa steel irradiated in FFTF does not saturate with fluence by {approx}28 dpa, whereas for the 9Cr-2WV steel and most similar steels, saturation occurs at <10 dpa, and (2) the shift in DBTT for 9Cr-2WVTa steel irradiated in FFTF and HFR increased with irradiation temperature, whereas it decreased for the 9Cr-2WV steel, as it does for most similar steels. The improved properties of the 9Cr-2WVTa steel and the differences with other steels were attributed to tantalum in solution.

  4. Aging degradation of cast stainless steel

    SciTech Connect

    Chopra, O.K.; Chung, H.M.

    1985-10-01

    A program is being conducted to investigate the significance of in-service embrittlement of cast-duplex stainless steels under light-water reactor operating conditions. Data from room-temperature Charpy-impact tests for several heats of cast stainless steel aged up to 10,000 h at 350, 400, and 450/sup 0/C are presented and compared with results from other studies. Microstructures of cast-duplex stainless steels subjected to long-term aging either in the laboratory or in reactor service have been characterized. The results indicate that at least two processes contribute to the low-temperature embrittleent of duplex stainless steels, viz., weakening of the ferrite/austenite phase boundary by carbide precipitation and embrittlement of ferrite matrix by the formation of additional phases such as G-phase, Type X, or the ..cap alpha..' phase. Carbide precipitation has a significant effect on the onset of embrittlement of CF-8 and -8M grades of stainless steels aged at 400 or 450/sup 0/C. The existing correlations do not accurately represent the embrittlement behavior over the temperature range 300 to 450/sup 0/C. 18 refs., 13 figs.

  5. Dislocation substructure in fatigued duplex stainless steel

    SciTech Connect

    Polak, J. . Lab. de Mecanique de Lille Inst. of Physical Metallurgy, Brno . Academy of Sciences); Degallaix, S. . Lab. de Mecanique de Lille); Kruml, T. . Academy of Sciences)

    1993-12-15

    Cyclic plastic straining of crystalline materials results in the formation of specific dislocation structures. Considerable progress in mapping and understanding internal dislocation structures has been achieved by studying single crystal behavior: however, most structural materials have a polycrystalline structure and investigations of polycrystals in comparison to single crystal behavior of simple metals prove to be very useful in understanding more complex materials. There are some classes of materials, however, with complicated structure which do not have a direct equivalent in single crystalline form. Moreover, the specific dimensions and shapes of individual crystallites play an important role both in the cyclic stress-strain response of these materials and in the formation of their interior structure in cyclic straining. Austenitic-ferritic duplex stainless steel, which is a kind of a natural composite, is a material of this type. The widespread interest in the application of duplex steels is caused by approximately doubled mechanical properties and equal corrosion properties, when compared with classical austenitic stainless steels. Fatigue resistance of these steels as well as the surface damage evolution in cyclic straining have been studied; however, much less is known about the internal substructure development in cyclic straining. In this study the dislocation arrangement in ferritic and austenitic grains of the austenitic-ferritic duplex steel alloyed with nitrogen and cyclically strained with two strain amplitudes, is reported and compared to the dislocation arrangement found in single and polycrystals of austenitic and ferritic materials of a similar composition and with the surface relief produced in cyclic plastic straining.

  6. High Strength, Weldable Precipitation Aged Steels

    NASA Astrophysics Data System (ADS)

    Wilson, Alexander D.

    1987-03-01

    The family of plate steels represented by ASTM Specification A7101 is finding increasing applications. These low carbon, Cu-Ni-Cr-Mo-Cb, copper precipitation hardened steels have been identified by a number of designations over the years. During early development in the late 1960's and first commercial production in 1970, the steels were known as IN-787 (trademark of International Nickel Company).2 ASTM specifications were subsequently developed for structural (A710) and pressure vessel (A736) applications over ten years ago. More recent interest and application of this family of steels by the U.S. Navy has lead to development of a military specification MIL-S-24645 (SH),3 also initially known as "HSLA-80." Significant tonnage is being produced for the U.S. Navy as a replacement for HY80 (MIL-S-16216) in cruiser deck, bulkhead and hull applications.4 In these applications, the enhanced weldability and requirement of no preheat at this high strength and toughness level has been the main motivation for its use. Over the past 15 years, A710 type steels have also been used in a variety of applications, including off-shore platforms, pressure vessels, arctic linepipe valves and off-highway mining truck frames.

  7. Superplastic forming of stainless steel automotive components

    SciTech Connect

    Bridges, B.; Elmer, J.; Carol, L.

    1997-02-06

    Exhaust emission standards are governmentally controlled standards, which are increasingly stringent, forcing alternate strategies to meet these standards. One approach to improve the efficiency of the exhaust emission equipment is to decrease the time required to get the catalytic converter to optimum operating temperature. To accomplish this, automotive manufacturers are using double wall stainless steel exhaust manifolds to reduce heat loss of the exhaust gases to the converter. The current method to manufacture double wall stainless steel exhaust components is to use a low-cost alloy with good forming properties and extensively form, cut, assemble, and weld the pieces. Superplastic forming (SPF) technology along with alloy improvements has potential at making this process more cost effective. Lockheed Martin Energy Systems (LMES), Lawrence Livermore National Laboratory (LLNL) and USCAR Low Emission Partnership (LEP) worked under a Cooperative Research And Development Agreement (CRADA) to evaluate material properties, SPF behavior, and welding behavior of duplex stainless steel alloy for automotive component manufacturing. Battelle Pacific Northwest National Laboratory (PNNL) has a separate CRADA with the LEP to use SPF technology to manufacture a double wall stainless steel exhaust component. As a team these CRADAs developed and demonstrated a technical plan to accomplish making double wall stainless steel exhaust manifolds.

  8. Process development of thin strip steel casting

    SciTech Connect

    Sussman, R.C.; Williams, R.S.

    1990-12-01

    An important new frontier is being opened in steel processing with the emergence of thin strip casting. Casting steel directly to thin strip has enormous benefits in energy savings by potentially eliminating the need for hot reduction in a hot strip mill. This has been the driving force for numerous current research efforts into the direct strip casting of steel. The US Department of Energy initiated a program to evaluate the development of thin strip casting in the steel industry. In earlier phases of this program, planar flow casting on an experimental caster was studied by a team of engineers from Westinghouse Electric corporation and Armco Inc. A subsequent research program was designed as a fundamental and developmental study of both planar and melt overflow casting processes. This study was arranged as several separate and distinct tasks which were often completed by different teams of researchers. An early task was to design and build a water model to study fluid flow through different designs of planar flow casting nozzles. Another important task was mathematically modeling of melt overflow casting process. A mathematical solidification model for the formation of the strip in the melt overflow process was written. A study of the material and conditioning of casting substrates was made on the small wheel caster using the melt overflow casting process. This report discusses work on the development of thin steel casting.

  9. Bearing and gear steels for aerospace applications

    NASA Technical Reports Server (NTRS)

    Zaretsky, Erwin V.

    1990-01-01

    Research in metallurgy and processing for bearing and gear steels has resulted in improvements in rolling-element bearing and gear life for aerospace application by a factor of approximately 200 over that obtained in the early 1940's. The selection and specification of a bearing or gear steel is dependent on the integration of multiple metallurgical and physical variables. For most aerospace bearings, through-hardened VIM-VAR AISI M-50 steel is the material of preference. For gears, the preferential material is case-carburized VAR AISI 9310. However, the VAR processing for this material is being replaced by VIM-VAR processing. Since case-carburized VIM-VAR M-50NiL incorporates the desirable qualities of both the AISI M-50 and AISI 9310 materials, optimal life and reliability can be achieved in both bearings and gears with a single steel. Hence, this material offers the promise of a common steel for both bearings and gears for future aerospace applications.

  10. 3. INTERIOR VIEW OF SMOKEHOUSE UNIT; NOTE STAINLESS STEEL NOZZLES ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    3. INTERIOR VIEW OF SMOKEHOUSE UNIT; NOTE STAINLESS STEEL NOZZLES THAT INTRODUCED SMOKE INTO UNIT; FLOOR IS UNPAINTED STEEL - Rath Packing Company, Smokehouse-Hog Chilling Building, Sycamore Street between Elm & Eighteenth Streets, Waterloo, Black Hawk County, IA

  11. Diamond machining of steel molds for optical components

    NASA Astrophysics Data System (ADS)

    Bohr, Roland

    2016-08-01

    The requirement of ultra precision diamond machining of lens molds in steel is identified. A solution for this type of machining is presented and results of such a machining in steel compared to standard milling and polishing process are shown.

  12. 1. VIEW NORTHEASTWEST AND SOUTH ELEVATIONS OF THE BETHLEHEM STEEL ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    1. VIEW NORTHEAST-WEST AND SOUTH ELEVATIONS OF THE BETHLEHEM STEEL COMPANY SHIPYARD CARPENTER SHOP. - Bethlehem Steel Company Shipyard, Carpenter Shop, 1201-1321 Hudson Street, Hoboken, Hudson County, NJ

  13. 4. VIEW EASTSOUTH ELEVATION OF THE BETHLEHEM STEEL COMPANY SHIPYARD ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. VIEW EAST-SOUTH ELEVATION OF THE BETHLEHEM STEEL COMPANY SHIPYARD BLACKSMITH SHOP/BOILER SHOP. - Bethlehem Steel Company Shipyard, Blacksmith Shop-Boiler Shop, 1201-1321 Hudson Street, Hoboken, Hudson County, NJ

  14. 1. VIEW WESTEAST ELEVATION OF THE BETHLEHEM STEEL COMPANY SHIPYARD ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    1. VIEW WEST-EAST ELEVATION OF THE BETHLEHEM STEEL COMPANY SHIPYARD BLACKSMITH SHOP/BOILER SHOP. - Bethlehem Steel Company Shipyard, Blacksmith Shop-Boiler Shop, 1201-1321 Hudson Street, Hoboken, Hudson County, NJ

  15. Nickel-free austenitic stainless steels for medical applications

    PubMed Central

    Yang, Ke; Ren, Yibin

    2010-01-01

    The adverse effects of nickel ions being released into the human body have prompted the development of high-nitrogen nickel-free austenitic stainless steels for medical applications. Nitrogen not only replaces nickel for austenitic structure stability but also much improves steel properties. Here we review the harmful effects associated with nickel in medical stainless steels, the advantages of nitrogen in stainless steels, and emphatically, the development of high-nitrogen nickel-free stainless steels for medical applications. By combining the benefits of stable austenitic structure, high strength and good plasticity, better corrosion and wear resistances, and superior biocompatibility compared to the currently used 316L stainless steel, the newly developed high-nitrogen nickel-free stainless steel is a reliable substitute for the conventional medical stainless steels. PMID:27877320

  16. 5. SOUTHERN END OF INTERIOR OF STEEL FRAMEWORK TRAIN SHED ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    5. SOUTHERN END OF INTERIOR OF STEEL FRAMEWORK TRAIN SHED LOOKING SE TO CAVED IN SHED, CENTER, AND BRICK AND STEEL SHED. - Western Railway of Alabama Montgomery Rail Shops, 701 North Perry Street, Montgomery, Montgomery County, AL

  17. View of steel warehouses (building 710 second in on right); ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View of steel warehouses (building 710 second in on right); camera facing south. - Naval Supply Annex Stockton, Steel Warehouse Type, Between James & Humphreys Drives south of Embarcadero, Stockton, San Joaquin County, CA

  18. View of steel warehouses (from left: building 807, 808, 809, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View of steel warehouses (from left: building 807, 808, 809, 810, 811); camera facing east. - Naval Supply Annex Stockton, Steel Warehouse Type, Between James & Humphreys Drives south of Embarcadero, Stockton, San Joaquin County, CA

  19. View of steel warehouses, building 710 north sidewalk; camera facing ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View of steel warehouses, building 710 north sidewalk; camera facing east. - Naval Supply Annex Stockton, Steel Warehouse Type, Between James & Humphreys Drives south of Embarcadero, Stockton, San Joaquin County, CA

  20. View of steel warehouses on Ellsberg Drive, building 710 full ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View of steel warehouses on Ellsberg Drive, building 710 full building at center; camera facing southeast. - Naval Supply Annex Stockton, Steel Warehouse Type, Between James & Humphreys Drives south of Embarcadero, Stockton, San Joaquin County, CA

  1. First Structural Steel Erected at NSLS-II

    ScienceCinema

    None

    2016-07-12

    Ten steel columns were incorporated into the ever-growing framework for the National Synchrotron Light Source II last week, the first structural steel erected for the future 400,000-square-foot facility.

  2. View of steel warehouses (building 710 second in on left); ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View of steel warehouses (building 710 second in on left); camera facing west. - Naval Supply Annex Stockton, Steel Warehouse Type, Between James & Humphreys Drives south of Embarcadero, Stockton, San Joaquin County, CA

  3. View of steel warehouses at Gilmore Avenue (building 710 second ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View of steel warehouses at Gilmore Avenue (building 710 second in on left); camera facing east. - Naval Supply Annex Stockton, Steel Warehouse Type, Between James & Humphreys Drives south of Embarcadero, Stockton, San Joaquin County, CA

  4. First Structural Steel Erected at NSLS-II

    SciTech Connect

    2009-09-14

    Ten steel columns were incorporated into the ever-growing framework for the National Synchrotron Light Source II last week, the first structural steel erected for the future 400,000-square-foot facility.

  5. 76 FR 18781 - Certain Steel Wheels From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-05

    ... From the Federal Register Online via the Government Publishing Office INTERNATIONAL TRADE COMMISSION Certain Steel Wheels From China AGENCY: United States International Trade Commission. ACTION... the United States is materially retarded, by reason of imports from China of certain steel...

  6. 20. DETAILED OBLIQUE VIEW SOUTHWEST FURNACE 2, SHOWING STEEL FRAME ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    20. DETAILED OBLIQUE VIEW SOUTHWEST FURNACE 2, SHOWING STEEL FRAME BOXES FOR COUNTERWEIGHTS, AND FURNACE HEATING PIPES AT RIGHT. - Vulcan Crucible Steel Company, Building No. 3, 100 First Street, Aliquippa, Beaver County, PA

  7. 19. 1500 CUBIC FEET CAPACITY SCRAP STEEL CHARGING BOX ON ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    19. 1500 CUBIC FEET CAPACITY SCRAP STEEL CHARGING BOX ON THE CHARGING AISLE OF THE BOP SHOP LOOKING NORTHWEST. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

  8. Symbiosis of Steel, Energy, and CO2 Evolution in Korea

    NASA Astrophysics Data System (ADS)

    Lee, Hyunjoung; Matsuura, Hiroyuki; Sohn, Il

    2016-09-01

    This study looks at the energy intensity of the steel industry and the greenhouse gas intensity involved with the production of steel. Using several sources of steel production data and the corresponding energy sources used provides a time-series analysis of the greenhouse gas (GHG) and energy intensity from 1990 to 2014. The impact of the steel economy with the gross domestic product (GDP) provides indirect importance of the general manufacturing sector within Korea and in particular the steel industry. Beyond 2008, the shift in excess materials production and significant increase in total imports have led to an imbalance in the Korean steel market and continue to inhibit the growth of the domestic steel market. The forecast of the GHG and energy intensity along with the steel production up to 2030 is provided using the auto regressive integrated moving average analysis.

  9. Northwest view of steel plate "cans" in bay 7 of ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Northwest view of steel plate "cans" in bay 7 of the main pipe mill building. Historian for scale. - U.S. Steel National Tube Works, Main Pipe Mill Building, Along Monongahela River, McKeesport, Allegheny County, PA

  10. Diffusion bonding between ODS ferritic steel and F82H steel for fusion applications

    NASA Astrophysics Data System (ADS)

    Noh, Sanghoon; Kim, Byungjun; Kasada, Ryuta; Kimura, Akihiko

    2012-07-01

    Diffusion bonding techniques were employed to join high Cr oxide dispersion strengthened (ODS) ferritic steel (Fe-15Cr-2W-0.2Ti-0.35Y2O3) and F82H steel under uni-axial hydrostatic pressure using a high vacuum hot press, and the microstructure and mechanical properties of the joints were investigated. The dissimilar joints were bonded by solid-state diffusion bonding (SSDB) and liquid phase diffusion bonding (LPDB). After bonding process, heat treatments were conducted to utilize the phase transformation of F82H steel for recovering the martensitic structure. Tensile tests with miniaturized specimens were carried out to investigate and compare the bonding strengths of each joint. Microstructure was observed for the bonding interface, and fracture mode was investigated after the tensile tests. LPDB joint of interfacial F82H steel fully recovered to martensite phase by post-joining heat treatments, while SSDB joint had ferrite phases at the interface even after heat treatment, which is considered to be due to decarburization of F82H steel during the bonding process. Therefore it is considered that the insert material plays a role as diffusion barrier of carbon during LPDB process. Microstructure observations and tensile tests of the joints revealed that the LPDB joints possess suitable tensile properties which are comparable to that of F82H steel. This indicates that LPDB is more promising method to bond ODS-FS and F82H steel than SSDB.

  11. Enhanced Inclusion Removal from Steel in the Tundish

    SciTech Connect

    R. C. Bradt; M.A.R. Sharif

    2009-09-25

    The objective of this project was to develop an effective chemical filtering system for significantly reducing the content of inclusion particles in the steel melts exiting the tundish for continuous casting. This project combined a multi-process approach that aimed to make significant progress towards an "inclusion free" steel by incorporating several interdependent concepts to reduce the content of inclusions in the molten steel exiting the tundish for the caster. The goal is to produce "cleaner" steel.

  12. Enhanced Incluison Removal from Steel in the Tundish

    SciTech Connect

    R.C. Bradt; M.A.R. Sharif

    2009-09-25

    The objective of this project was to develop an effective chemical filtering system for significantly reducing the content of inclusion particles in the steel melts exiting the tundish for continuous casting. This project combined a multi-process approach that aimed to make significant progress towards an "inclusion free" steel by incorporating several interdependent concepts to reduce the content of inclusions in the molten steel exiting the tundish for the caster. The goal is to produce "cleaner" steel.

  13. Corrosion inhibition of reinforcing steel by using acrylic latex

    SciTech Connect

    Wang, S.X.; Lin, W.W.; Ceng, S.A.; Zhang, J.Q.

    1998-05-01

    Acrylic latex was introduced into steel-reinforcing steel concrete as concrete admixtures or rebar coatings in order to prevent corrosion of steel reinforcements. The results showed that applying the latex by both methods took effect in different ways, while the latter was more noticeable. The corrosion prevention mechanism and the surface state of the steel rebar were also explored, based on which suggestions for enhancing the corrosion-resistant ability were made.

  14. Effect of rust on the wettability of steel by water

    SciTech Connect

    Lu, W.; Chung, D.D.L.

    1998-04-01

    Rust, as formed on steel by immersion of low-carbon steel in water, was found to improve the wettability of steel by water. The advancing contact angle decreased from 87{degree} to 32{degree}, and the receding contact angle decreased from 81{degree} to 29{degree}. Cleansing of steel by acetone also helped improve the wettability, but the advancing angle only decreased from 87{degree} to 73{degree}, and the receding angle only decreased from 81{degree} to 41{degree}.

  15. High Strength Steel Weldment Reliability: Weld Metal Hydrogen Trapping.

    DTIC Science & Technology

    1998-02-01

    additions to welding consumables to control weld metal hydrogen and thus reduce susceptibility to cold cracking in high strength steel weldments. 14...applying weld metal hydrogen trapping to improve the resistance to hydrogen cracking in welding of high strength steels . Hydrogen cracking in high...requirements which are necessary to prevent hydrogen cracking in high strength steel welding. Common practices to prevent hydrogen cracking in steel

  16. Heat Treatment and Properties of Iron and Steel

    DTIC Science & Technology

    2007-11-02

    specified as an added element to a standard steel. • Silicon: Because of the technological nature of the process , acid bessemer steels are not...Heat treatment of steels 9 5.1. Annealing ~ 10 a. Full annealing I__ 10 b. Process annealing 10 c. Spheroidizing . 10 5.2. Normalizing 10...treatment of iron and steel and for directions and explanations of such processes . This Monograph has been prepared to answer such inquiries and to give

  17. Application of RST in the steel industry

    NASA Astrophysics Data System (ADS)

    Raman, R. V.; Maringer, R. E.

    1982-05-01

    The rapid solidification technology (RST) involves quenching molten metals at rates of perhaps 102 to 1010 degrees C per second. First reported in 1960, RST has experienced rapid growth during the last decade and is now established on the commercial market-place. This has resulted from the simple facts that unusual properties result from RST, that relatively easy techniques are available to produce large quantities of material, and that applications for these materials have been recognized. Ferrous-base materials produced by RST methods include staple fibers of mild and stainless steel for incorporation into concrete and castable refractories, powder metallurgy tool steels, and amorphous strip for power transformers. Research results suggest that RST will have a strong continuing influence on ferrous powder metallurgy, on the direct casting of strip and foil of carbon and stainless steel, and on core materials for motor and transformers.

  18. Fracture mechanism of borated stainless steel

    SciTech Connect

    He, J.Y.; Soliman, S.E.; Baratta, A.J.; Balliett, T.A.

    2000-05-01

    The mechanical properties and fracture mechanism of irradiated and unirradiated boron containing Type 304 stainless steel are studied. Four different batches with different boron weight percentages are used. One of these batches was manufactured by a conventional wrought technique, while the others were manufactured by a powder metallurgy technique. The irradiated specimens were subjected to a fluence level of 5 x 10{sup 19} or 1 {times} 10{sup 21} n/m{sup 2}. The mechanical and fracture tests were performed at temperatures of 233, 298, and 533 K. No significant effects on the mechanical properties or fracture behavior were observed as a result of neutron irradiation and/or temperature. The ductility and toughness of the borated steel were found to decrease with increasing boron content. The effect of boride on void nucleation and linkage was found to play an important role in the fracture behavior of borated steel.

  19. Microstructure and cleavage in lath martensitic steels.

    PubMed

    Morris, John W; Kinney, Chris; Pytlewski, Ken; Adachi, Y

    2013-02-01

    In this paper we discuss the microstructure of lath martensitic steels and the mechanisms by which it controls cleavage fracture. The specific experimental example is a 9Ni (9 wt% Ni) steel annealed to have a large prior austenite grain size, then examined and tested in the as-quenched condition to produce a relatively coarse lath martensite. The microstructure is shown to approximate the recently identified 'classic' lath martensite structure: prior austenite grains are divided into packets, packets are subdivided into blocks, and blocks contain interleaved laths whose variants are the two Kurjumov-Sachs relations that share the same Bain axis of the transformation. When the steel is fractured in brittle cleavage, the laths in the block share {100} cleavage planes and cleave as a unit. However, cleavage cracks deflect or blunt at the boundaries between blocks with different Bain axes. It follows that, as predicted, the block size governs the effective grain size for cleavage.

  20. Residual stress measurements in carbon steel

    NASA Technical Reports Server (NTRS)

    Heyman, J. S.; Min, N.

    1986-01-01

    External dc magnetic field-induced changes in natural velocity of Rayleigh surface waves were measured in steel specimens under various stress conditions. The low field slopes of curves representing the fractional changes of natural velocity were proved to provide correct stress information in steels with different metallurgical properties. The slopes of curves under uniaxial compression, exceeding about one third of the yield stress, fell below zero in all the specimens when magnetized along the stress axis. The slopes under tension varied among different steels but remained positive in any circumstances. The stress effect was observed for both applied and residual stress. A physical interpretation of these results is given based on the stress-induced domain structure changes and the delta epsilon effect. Most importantly, it is found that the influence of detailed metallurgical properties cause only secondary effects on the obtained stress information.

  1. Solidification Sequence of Spray-Formed Steels

    NASA Astrophysics Data System (ADS)

    Zepon, Guilherme; Ellendt, Nils; Uhlenwinkel, Volker; Bolfarini, Claudemiro

    2016-02-01

    Solidification in spray-forming is still an open discussion in the atomization and deposition area. This paper proposes a solidification model based on the equilibrium solidification path of alloys. The main assumptions of the model are that the deposition zone temperature must be above the alloy's solidus temperature and that the equilibrium liquid fraction at this temperature is reached, which involves partial remelting and/or redissolution of completely solidified droplets. When the deposition zone is cooled, solidification of the remaining liquid takes place under near equilibrium conditions. Scanning electron microscopy (SEM) and optical microscopy (OM) were used to analyze the microstructures of two different spray-formed steel grades: (1) boron modified supermartensitic stainless steel (SMSS) and (2) D2 tool steel. The microstructures were analyzed to determine the sequence of phase formation during solidification. In both cases, the solidification model proposed was validated.

  2. Ultrasonic Spectroscopy of Stainless Steel Sandwich Panels

    NASA Technical Reports Server (NTRS)

    Cosgriff, Laura M.; Lerch, Bradley A.; Hebsur, Mohan G.; Baaklini, George Y.; Ghosn, Louis J.

    2003-01-01

    Enhanced, lightweight material systems, such as 17-4PH stainless steel sandwich panels are being developed for use as fan blades and fan containment material systems for next generation engines. In order to improve the production for these systems, nondestructive evaluation (NDE) techniques, such as ultrasonic spectroscopy, are being utilized to evaluate the brazing quality between the 17-4PH stainless steel face plates and the 17-4PH stainless steel foam core. Based on NDE data, shear tests are performed on sections representing various levels of brazing quality from an initial batch of these sandwich structures. Metallographic characterization of brazing is done to corroborate NDE findings and the observed shear failure mechanisms.

  3. Microstructure and cleavage in lath martensitic steels

    NASA Astrophysics Data System (ADS)

    Morris, John W., Jr.; Kinney, Chris; Pytlewski, Ken; Adachi, Y.

    2013-02-01

    In this paper we discuss the microstructure of lath martensitic steels and the mechanisms by which it controls cleavage fracture. The specific experimental example is a 9Ni (9 wt% Ni) steel annealed to have a large prior austenite grain size, then examined and tested in the as-quenched condition to produce a relatively coarse lath martensite. The microstructure is shown to approximate the recently identified ‘classic’ lath martensite structure: prior austenite grains are divided into packets, packets are subdivided into blocks, and blocks contain interleaved laths whose variants are the two Kurjumov-Sachs relations that share the same Bain axis of the transformation. When the steel is fractured in brittle cleavage, the laths in the block share {100} cleavage planes and cleave as a unit. However, cleavage cracks deflect or blunt at the boundaries between blocks with different Bain axes. It follows that, as predicted, the block size governs the effective grain size for cleavage.

  4. Are Sulfate Reducing Bacteria Important to the Corrosion of Stainless Steels?

    DTIC Science & Technology

    2009-01-01

    endorsed b> the Association. Printed in the U.S.A. MATERIALS AND METHODS Sulfide was employed to convert surface metal oxide to metal sulfide on...medium and placed into a separate falcon tube. Corrosion products, iron oxides and sulfides, were removed following ASTM Standard Gl procedures2. The...has predominantly iron oxide on its surface, while with about 12% Cr, the oxide becomes mainly chromium oxide . UNS S31254 (Fe-20Cr-18Ni-6Mo) was chosen

  5. Neutron Irradiation Resistance of RAFM Steels

    SciTech Connect

    Gaganidze, Ermile; Dafferner, Bernhard; Aktaa, Jarir

    2008-07-01

    The neutron irradiation resistance of the reduced-activation ferritic/martensitic (RAFM) steel EUROFER97 and international reference steels (F82H-mod, OPTIFER-Ia, GA3X and MANET-I) have been investigated after irradiation in the Petten High Flux Reactor up to 16.3 dpa at different irradiation temperatures (250-450 deg. C). The embrittlement behavior and hardening are investigated by instrumented Charpy-V tests with sub-size specimens. Neutron irradiation-induced embrittlement and hardening of EUROFER97 was studied under different heat treatment conditions. Embrittlement and hardening of as-delivered EUROFER97 steel are comparable to those of reference steels. Heat treatment of EUROFER97 at a higher austenitizing temperature substantially improves the embrittlement behaviour at low irradiation temperatures. Analysis of embrittlement vs. hardening behavior of RAFM steels within a proper model in terms of the parameter C={delta}DBTT/{delta}{sigma} indicates hardening-dominated embrittlement at irradiation temperatures below 350 deg. C with 0.17 {<=} C {<=} 0.53 deg. C/MPa. Scattering of C at irradiation temperatures above 400 deg. C indicates non hardening embrittlement. A role of He in a process of embrittlement is investigated in EUROFER97 based steels, that are doped with different contents of natural B and the separated {sup 10}B-isotope (0.008-0.112 wt.%). Testing on small scale fracture mechanical specimens for determination of quasi-static fracture toughness will be also presented in a view of future irradiation campaigns. (authors)

  6. Mechanical Property Characterization of ESR (Electroslag Remelted) 4353 Steel with a Comparison to ESR 4340 Steel

    DTIC Science & Technology

    1987-04-01

    IThe ESR 4J53 steel exhibits Charpy impact energy values of 12.4 ftib for 400 and 4504 tempers, which decrease to 9.2 ft&,jb for a 5000f temper as a...temperature or hard- ness, the ESR 4340 steel has greater Charpy impact energy and fracture tough- ness( KI )i. -w N .: UNCLASS IF I ED S Cul...pertinent for the consideration of high strength steels for Army applications include tensile -4 properties, hardness, Charpy V-notch impact energy

  7. Structure and properties of a steel/white-cast-iron bimetal produced by method of carbonizing the steel melt

    NASA Astrophysics Data System (ADS)

    Sapozhnikov, S. Z.

    1985-11-01

    Centrifugal bimetallization by the method of carbonizing the steel melt makes it possible to obtain a steel/white-cast-iron composition with a cladding layer close to the eutectic in terms of composition.

  8. Guidelines for structural bolting in accordance with the AISC (American Institute of Steel Construction) eighth edition manual of steel construction''

    SciTech Connect

    Western, J.L.; Johns, D.M.

    1990-05-11

    This paper specifies the usage of structural bolts in terms of their design, selection and application, in accordance with the American Institute of Steel Construction (AISC) Eighth Edition. Manual of Steel Construction.'' 1 tab.

  9. Experimental and Theoretical Investigations of Hot Isostatically Pressed-Produced Stainless Steel/High Alloy Tool Steel Compound Materials

    NASA Astrophysics Data System (ADS)

    Lindwall, Greta; Flyg, Jesper; Frisk, Karin; Sandberg, Odd

    2011-05-01

    Consolidation of tool steel powders and simultaneous joining to a stainless 316L steel are performed by hot isostatic pressing (HIP). Two tool steel grades are considered: a high vanadium alloyed carbon tool steel, and a high vanadium and chromium alloyed nitrogen tool steel. The boundary layer arising during diffusion bonding is in focus and, in particular, the diffusion of carbon and nitrogen over the joint. Measurements of the elemental concentration profiles and corrosion tests by the double loop-electrochemical potentiokinetic reactivation (DL-EPR) method are performed. Comparative calculations with the DICTRA software are performed and are found to be in agreement with the experimental results. It is found that the carbon tool steel grade has a more critical influence on the corrosion resistance of the stainless 316L steel in comparison to the nitrogen tool steel grade.

  10. Study of hot hardness characteristics of tool steels

    NASA Technical Reports Server (NTRS)

    Chevalier, J. L.; Dietrich, M. W.; Zaretsky, E. V.

    1972-01-01

    Hardness measurements of tool steel materials in electric furnace at elevated temperatures and low oxygen environment are discussed. Development of equation to predict short term hardness as function of intial room temperature hardness of steel is reported. Types of steel involved in the process are identified.

  11. Complex alloy steel for heavily loaded carburized gear wheels

    NASA Astrophysics Data System (ADS)

    Tel'dekov, V. A.; Merilova, E. A.; Shevchuk, V. P.

    1987-05-01

    The tendency of steel 18KhGN2MFB towards internal oxidation and austenite grain growth during CHT is markedly lower than for steel 20KhNZA normally used for gear wheels. Steel 18KhGN2MFB has sufficiently high hardenability for the carburized and carbonitrided layers.

  12. Explosive welding technique for joining aluminum and steel tubes

    NASA Technical Reports Server (NTRS)

    Wakefield, M. E.

    1975-01-01

    Silver sheet is wrapped around aluminum portion of joint. Mylar powder box is wrapped over silver sheet. Explosion welds silver to aluminum. Stainless-steel tube is placed over silver-aluminum interface. Mylar powder box, covered with Mylar tape, is wrapped around steel member. Explosion welds steel to silver-aluminum interface.

  13. Welding of Aluminum Alloys to Steels: An Overview

    DTIC Science & Technology

    2013-08-01

    95] K. Kimapong1, T. Watanabe, Effect of welding process parameters on mechanical property of FSW lap joint between aluminum alloy and steel ...UNCLASSIFIED: Distribution Statement A. Approved for public release. 1 UNCLASSIFIED Welding of aluminum alloys to steels : an overview M. Mazar...welding methods for joining aluminum alloys to steels . The microstructural development, mechanical properties and application of the joints are discussed

  14. 75 FR 41889 - Certain Steel Grating From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-07-19

    ... COMMISSION Certain Steel Grating From China Determination On the basis of the record \\1\\ developed in the... steel grating from China, provided for in subheading 7308.90.70 of the Harmonized Tariff Schedule of the... imports of certain steel gratings from China were being subsidized within the meaning of section 703(b)...

  15. Micronutrient availability from steel slag amendment in pine bark substrates

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Steel slag is a byproduct of the steel industry that can be used as a liming agent, but also has a high mineral nutrient content. While micronutrients are present in steel slag, it is not known if the mineral form of the micronutrients would render them available for plant uptake. The objective of...

  16. 21 CFR 872.3350 - Gold or stainless steel cusp.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Gold or stainless steel cusp. 872.3350 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3350 Gold or stainless steel cusp. (a) Identification. A gold or stainless steel cusp is a prefabricated device made of austenitic alloys or...

  17. 19 CFR 360.104 - Steel import monitoring.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 19 Customs Duties 3 2014-04-01 2014-04-01 false Steel import monitoring. 360.104 Section 360.104 Customs Duties INTERNATIONAL TRADE ADMINISTRATION, DEPARTMENT OF COMMERCE STEEL IMPORT MONITORING AND ANALYSIS SYSTEM § 360.104 Steel import monitoring. (a) Throughout the duration of the licensing...

  18. 49 CFR Appendix A to Part 178 - Specifications for Steel

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Specifications for Steel A Appendix A to Part 178... to Part 178—Specifications for Steel Table 1 Designation Chemical composition, percent-ladle analysis... be 1.40 percent. 6 Rephosphorized Grade 3 steels containing no more than 0.15 percent phosphorus...

  19. 46 CFR 154.170 - Outer hull steel plating.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Outer hull steel plating. 154.170 Section 154.170... Structure § 154.170 Outer hull steel plating. (a) Except as required in paragraph (b) of this section, the outer hull steel plating, including the shell and deck plating must meet the material standards of...

  20. 21 CFR 878.4495 - Stainless steel suture.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Stainless steel suture. 878.4495 Section 878.4495...) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4495 Stainless steel suture. (a) Identification. A stainless steel suture is a needled or unneedled nonabsorbable surgical suture composed of...

  1. 29 CFR 1926.858 - Removal of steel construction.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 29 Labor 8 2014-07-01 2014-07-01 false Removal of steel construction. 1926.858 Section 1926.858... of steel construction. (a) When floor arches have been removed, planking in accordance with § 1926.855(b) shall be provided for the workers engaged in razing the steel framing. (b) Cranes,...

  2. 19 CFR 360.104 - Steel import monitoring.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 19 Customs Duties 3 2010-04-01 2010-04-01 false Steel import monitoring. 360.104 Section 360.104 Customs Duties INTERNATIONAL TRADE ADMINISTRATION, DEPARTMENT OF COMMERCE STEEL IMPORT MONITORING AND ANALYSIS SYSTEM § 360.104 Steel import monitoring. (a) Throughout the duration of the licensing...

  3. 49 CFR 192.371 - Service lines: Steel.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Service lines: Steel. 192.371 Section 192.371 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY... § 192.371 Service lines: Steel. Each steel service line to be operated at less than 100 p.s.i. (689...

  4. 78 FR 7451 - Clad Steel Plate From Japan; Determination

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-02-01

    ... COMMISSION Clad Steel Plate From Japan; Determination On the basis of the record \\1\\ developed in the subject... order on clad steel plate from Japan would be likely to lead to continuation or recurrence of material... contained in USITC Publication 4370 (January 2013), entitled Clad Steel Plate from Japan: Investigation...

  5. 21 CFR 878.4495 - Stainless steel suture.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Stainless steel suture. 878.4495 Section 878.4495...) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4495 Stainless steel suture. (a) Identification. A stainless steel suture is a needled or unneedled nonabsorbable surgical suture composed of...

  6. 49 CFR 192.371 - Service lines: Steel.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Service lines: Steel. 192.371 Section 192.371 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY... § 192.371 Service lines: Steel. Each steel service line to be operated at less than 100 p.s.i. (689...

  7. 78 FR 78382 - Steel Nails From China; Determination

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-12-26

    ... COMMISSION Steel Nails From China; Determination On the basis of the record \\1\\ developed in the subject five... order on steel nails from China would be likely to lead to continuation or recurrence of material injury... contained in USITC Publication 4442 (December 2013), entitled Steel Nails from China: Investigation No....

  8. 77 FR 64545 - Drawn Stainless Steel Sinks From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-10-22

    ... COMMISSION Drawn Stainless Steel Sinks From China Scheduling of the final phase of countervailing duty and... retarded, by reason of subsidized and less-than-fair-value imports from China of drawn stainless steel... merchandise as ``drawn stainless steel sinks with single or multiple drawn bowls, with or without drain...

  9. 30 CFR 56.7050 - Tool and drill steel racks.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tool and drill steel racks. 56.7050 Section 56... Jet Piercing Drilling § 56.7050 Tool and drill steel racks. Receptacles or racks shall be provided for drill steel and tools stored or carried on drills....

  10. 49 CFR 192.309 - Repair of steel pipe.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Repair of steel pipe. 192.309 Section 192.309... Lines and Mains § 192.309 Repair of steel pipe. (a) Each imperfection or damage that impairs the serviceability of a length of steel pipe must be repaired or removed. If a repair is made by grinding,...

  11. 46 CFR 154.188 - Membrane tank: Inner hull steel.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 5 2011-10-01 2011-10-01 false Membrane tank: Inner hull steel. 154.188 Section 154.188... Structure § 154.188 Membrane tank: Inner hull steel. For a vessel with membrane tanks, the inner hull... “Rules for Building and Classing Steel Vessels”, 1981....

  12. 77 FR 28404 - Galvanized Steel Wire From China and Mexico

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-05-14

    ... COMMISSION Galvanized Steel Wire From China and Mexico Determinations On the basis of the record \\1... retarded, by reason of imports from China of galvanized steel wire, provided for in subheadings 7217.20.30... retarded, by reason of imports from Mexico of galvanized steel wire, provided for in subheadings...

  13. 46 CFR 154.188 - Membrane tank: Inner hull steel.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 5 2012-10-01 2012-10-01 false Membrane tank: Inner hull steel. 154.188 Section 154.188... Structure § 154.188 Membrane tank: Inner hull steel. For a vessel with membrane tanks, the inner hull... “Rules for Building and Classing Steel Vessels”, 1981....

  14. 30 CFR 57.7050 - Tool and drill steel racks.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tool and drill steel racks. 57.7050 Section 57... Rotary Jet Piercing Drilling-Surface and Underground § 57.7050 Tool and drill steel racks. Receptacles or racks shall be provided for drill steel and tools stored or carried on drills....

  15. 21 CFR 872.3350 - Gold or stainless steel cusp.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Gold or stainless steel cusp. 872.3350 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3350 Gold or stainless steel cusp. (a) Identification. A gold or stainless steel cusp is a prefabricated device made of austenitic alloys or...

  16. 76 FR 19382 - Galvanized Steel Wire From China and Mexico

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-07

    ... COMMISSION Galvanized Steel Wire From China and Mexico AGENCY: United States International Trade Commission... Mexico of galvanized steel wire, provided for in subheading 7217.20.30 and 7217.20.45 of the Harmonized...., Nashville, TN; National Standard, LLC, Niles, MI; and Oklahoma Steel and Wire Co., Inc., Madill,...

  17. 19 CFR 360.104 - Steel import monitoring.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 19 Customs Duties 3 2012-04-01 2012-04-01 false Steel import monitoring. 360.104 Section 360.104 Customs Duties INTERNATIONAL TRADE ADMINISTRATION, DEPARTMENT OF COMMERCE STEEL IMPORT MONITORING AND ANALYSIS SYSTEM § 360.104 Steel import monitoring. (a) Throughout the duration of the licensing...

  18. 30 CFR 57.7050 - Tool and drill steel racks.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Tool and drill steel racks. 57.7050 Section 57... Rotary Jet Piercing Drilling-Surface and Underground § 57.7050 Tool and drill steel racks. Receptacles or racks shall be provided for drill steel and tools stored or carried on drills....

  19. 30 CFR 57.7050 - Tool and drill steel racks.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Tool and drill steel racks. 57.7050 Section 57... Rotary Jet Piercing Drilling-Surface and Underground § 57.7050 Tool and drill steel racks. Receptacles or racks shall be provided for drill steel and tools stored or carried on drills....

  20. 30 CFR 57.7050 - Tool and drill steel racks.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Tool and drill steel racks. 57.7050 Section 57... Rotary Jet Piercing Drilling-Surface and Underground § 57.7050 Tool and drill steel racks. Receptacles or racks shall be provided for drill steel and tools stored or carried on drills....

  1. Web-Based Interactive Steel Sculpture for the Google Generation

    ERIC Educational Resources Information Center

    Chou, Karen C.; Moaveni, Saeed

    2009-01-01

    In almost all the civil engineering programs in the United States, a student is required to take at least one design course in either steel or reinforced concrete. One of the topics covered in an introductory steel design course is the design of connections. Steel connections play important roles in the integrity of a structure, and many…

  2. 30 CFR 56.7050 - Tool and drill steel racks.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Tool and drill steel racks. 56.7050 Section 56... Jet Piercing Drilling § 56.7050 Tool and drill steel racks. Receptacles or racks shall be provided for drill steel and tools stored or carried on drills....

  3. 21 CFR 872.3350 - Gold or stainless steel cusp.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Gold or stainless steel cusp. 872.3350 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3350 Gold or stainless steel cusp. (a) Identification. A gold or stainless steel cusp is a prefabricated device made of austenitic alloys or...

  4. 49 CFR Appendix A to Part 178 - Specifications for Steel

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Specifications for Steel A Appendix A to Part 178... to Part 178—Specifications for Steel Table 1 Designation Chemical composition, percent-ladle analysis... be 1.40 percent. 6 Rephosphorized Grade 3 steels containing no more than 0.15 percent phosphorus...

  5. 76 FR 38697 - High Pressure Steel Cylinders From China

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-07-01

    ... COMMISSION High Pressure Steel Cylinders From China Determinations On the basis of the record \\1\\ developed... injured by reason of imports from China of high pressure steel cylinders, provided for in subheading 7311... pressure steel cylinders from China. Accordingly, effective May 11, 2011, the Commission...

  6. 30 CFR 56.7050 - Tool and drill steel racks.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Tool and drill steel racks. 56.7050 Section 56... Jet Piercing Drilling § 56.7050 Tool and drill steel racks. Receptacles or racks shall be provided for drill steel and tools stored or carried on drills....

  7. 77 FR 1504 - Stainless Steel Wire Rod From India

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-01-10

    ... COMMISSION Stainless Steel Wire Rod From India Determination On the basis of the record \\1\\ developed in the... antidumping duty order on stainless steel wire rod From India would be likely to lead to continuation or... contained in USITC Publication 4300 (January 2012), entitled Stainless Steel Wire Rod From...

  8. 49 CFR 192.371 - Service lines: Steel.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Service lines: Steel. 192.371 Section 192.371 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY... § 192.371 Service lines: Steel. Each steel service line to be operated at less than 100 p.s.i. (689...

  9. 19 CFR 360.104 - Steel import monitoring.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 19 Customs Duties 3 2013-04-01 2013-04-01 false Steel import monitoring. 360.104 Section 360.104 Customs Duties INTERNATIONAL TRADE ADMINISTRATION, DEPARTMENT OF COMMERCE STEEL IMPORT MONITORING AND ANALYSIS SYSTEM § 360.104 Steel import monitoring. (a) Throughout the duration of the licensing...

  10. 75 FR 27428 - Safety Standards for Steel Erection

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-05-17

    ... Occupational Safety and Health Administration 29 CFR Part 1926 Safety Standards for Steel Erection AGENCY... technical amendment adds a nonmandatory note to the OSHA standards governing steel erection. The note... employers engaged in activities covered by OSHA's steel erection standards. DATES: Effective date: May...

  11. 30 CFR 57.7050 - Tool and drill steel racks.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Tool and drill steel racks. 57.7050 Section 57... Rotary Jet Piercing Drilling-Surface and Underground § 57.7050 Tool and drill steel racks. Receptacles or racks shall be provided for drill steel and tools stored or carried on drills....

  12. 21 CFR 872.3350 - Gold or stainless steel cusp.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Gold or stainless steel cusp. 872.3350 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3350 Gold or stainless steel cusp. (a) Identification. A gold or stainless steel cusp is a prefabricated device made of austenitic alloys or...

  13. 19 CFR 360.104 - Steel import monitoring.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 19 Customs Duties 3 2011-04-01 2011-04-01 false Steel import monitoring. 360.104 Section 360.104 Customs Duties INTERNATIONAL TRADE ADMINISTRATION, DEPARTMENT OF COMMERCE STEEL IMPORT MONITORING AND ANALYSIS SYSTEM § 360.104 Steel import monitoring. (a) Throughout the duration of the licensing...

  14. 30 CFR 56.7050 - Tool and drill steel racks.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Tool and drill steel racks. 56.7050 Section 56... Jet Piercing Drilling § 56.7050 Tool and drill steel racks. Receptacles or racks shall be provided for drill steel and tools stored or carried on drills....

  15. 29 CFR 1926.858 - Removal of steel construction.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 29 Labor 8 2012-07-01 2012-07-01 false Removal of steel construction. 1926.858 Section 1926.858... of steel construction. (a) When floor arches have been removed, planking in accordance with § 1926.855(b) shall be provided for the workers engaged in razing the steel framing. (b) Cranes,...

  16. 49 CFR 192.309 - Repair of steel pipe.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Repair of steel pipe. 192.309 Section 192.309... Lines and Mains § 192.309 Repair of steel pipe. (a) Each imperfection or damage that impairs the serviceability of a length of steel pipe must be repaired or removed. If a repair is made by grinding,...

  17. 29 CFR 1926.858 - Removal of steel construction.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 29 Labor 8 2011-07-01 2011-07-01 false Removal of steel construction. 1926.858 Section 1926.858... of steel construction. (a) When floor arches have been removed, planking in accordance with § 1926.855(b) shall be provided for the workers engaged in razing the steel framing. (b) Cranes,...

  18. 46 CFR 154.188 - Membrane tank: Inner hull steel.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 5 2014-10-01 2014-10-01 false Membrane tank: Inner hull steel. 154.188 Section 154.188... Structure § 154.188 Membrane tank: Inner hull steel. For a vessel with membrane tanks, the inner hull... “Rules for Building and Classing Steel Vessels”, 1981....

  19. 49 CFR 192.371 - Service lines: Steel.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Service lines: Steel. 192.371 Section 192.371 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY... § 192.371 Service lines: Steel. Each steel service line to be operated at less than 100 p.s.i. (689...

  20. 21 CFR 872.3350 - Gold or stainless steel cusp.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Gold or stainless steel cusp. 872.3350 Section 872...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3350 Gold or stainless steel cusp. (a) Identification. A gold or stainless steel cusp is a prefabricated device made of austenitic alloys or...