Science.gov

Sample records for 2-ethyl hexyl acrylate

  1. Method for the purification of bis (2-ethyl-hexyl)phosphoric acid

    DOEpatents

    Schulz, W.W.

    1974-02-19

    Foreign products including the neutral organophosphorous compounds and the iron salts normally present in commercial bis(2ethyl-hexyl) phosphoric acid(HDEHP), and the radiolytic degradation products of HDEHP on exposure of HDEHP to beta and gamma irradiation are removed from HDEHP containing one or more of such products by contacting the said foreign product containing HDEHP with a macroreticular anion exchange resin in base form whereby the DEHP- ion of HDEHP exchanges with the anion of the resin and is thus adsorbed on the resin and the said foreign products are not adsorbed and will pass through a bed of particles of the resin. The adsorbed DEHP- ion is then eluted from the resin and acidified to form and recover the purified HDEHP. (auth)

  2. Investigation on removal pathways of Di 2-ethyl hexyl phthalate from synthetic municipal wastewater using a submerged membrane bioreactor.

    PubMed

    Zolfaghari, Mehdi; Drogui, Patrick; Seyhi, Brahima; Brar, Satinder Kaur; Buelna, Gerardo; Dubé, Rino; Klai, Nouha

    2015-11-01

    Highly hydrophobic Di 2-ethyl hexyl phthalate (DEHP) is one of the most prevalent plasticizers in wastewaters. Since its half-life in biological treatment is around 25days, it can be used as an efficiency indicator of wastewater treatment plant for the removal of hydrophobic emerging contaminants. In this study, the performance of submerged membrane bioreactor was monitored to understand the effect of DEHP on the growth of aerobic microorganisms. The data showed that the chemical oxygen demand (COD) and ammonia concentration were detected below 10 and 1.0mg/L, respectively for operating conditions of hydraulic retention time (HRT)=4 and 6hr, sludge retention time (SRT)=140day and sludge concentration between 11.5 and 15.8g volatile solid (VS)/L. The removal efficiency of DEHP under these conditions was higher and ranged between 91% and 98%. Results also showed that the removal efficiency of DEHP in biological treatment depended on the concentration of sludge, as adsorption is the main mechanism of its removal. For the submerged membrane bioreactor, the pore size is the pivotal factor for DEHP removal, since it determines the amount of soluble microbial products coming out of the process. Highly assimilated microorganisms increase the biodegradation rate, as 74% of inlet DEHP was biodegraded; however, the concentration of DEHP inside sludge was beyond the discharge limit. Understanding the fate of DEHP in membrane bioreactor, which is one of the most promising and futuristic treatment process could provide replacement for conventional processes to satisfy the future stricter regulations on emerging contaminants.

  3. Investigation on removal pathways of Di 2-ethyl hexyl phthalate from synthetic municipal wastewater using a submerged membrane bioreactor.

    PubMed

    Zolfaghari, Mehdi; Drogui, Patrick; Seyhi, Brahima; Brar, Satinder Kaur; Buelna, Gerardo; Dubé, Rino; Klai, Nouha

    2015-11-01

    Highly hydrophobic Di 2-ethyl hexyl phthalate (DEHP) is one of the most prevalent plasticizers in wastewaters. Since its half-life in biological treatment is around 25days, it can be used as an efficiency indicator of wastewater treatment plant for the removal of hydrophobic emerging contaminants. In this study, the performance of submerged membrane bioreactor was monitored to understand the effect of DEHP on the growth of aerobic microorganisms. The data showed that the chemical oxygen demand (COD) and ammonia concentration were detected below 10 and 1.0mg/L, respectively for operating conditions of hydraulic retention time (HRT)=4 and 6hr, sludge retention time (SRT)=140day and sludge concentration between 11.5 and 15.8g volatile solid (VS)/L. The removal efficiency of DEHP under these conditions was higher and ranged between 91% and 98%. Results also showed that the removal efficiency of DEHP in biological treatment depended on the concentration of sludge, as adsorption is the main mechanism of its removal. For the submerged membrane bioreactor, the pore size is the pivotal factor for DEHP removal, since it determines the amount of soluble microbial products coming out of the process. Highly assimilated microorganisms increase the biodegradation rate, as 74% of inlet DEHP was biodegraded; however, the concentration of DEHP inside sludge was beyond the discharge limit. Understanding the fate of DEHP in membrane bioreactor, which is one of the most promising and futuristic treatment process could provide replacement for conventional processes to satisfy the future stricter regulations on emerging contaminants. PMID:26574086

  4. Copolymeric hexyl acrylate-methacrylic acid microspheres - surface vs. bulk reactive carboxyl groups. Coulometric and colorimetric determination and analytical applications for heterogeneous microtitration.

    PubMed

    Stelmach, Emilia; Maksymiuk, Krzysztof; Michalska, Agata

    2016-10-01

    Copolymeric acrylate microspheres were prepared from hexyl acrylate using different amounts of methacrylic acid, resulting in a series of microspheres of gradually changing properties. The distribution of carboxyl groups - between surface and bulk of microspheres was evaluated. Bulk reactive carboxyl groups were determined using reverse coulometric titration with H(+) ions, following hydroxide ions have been generated and allowed to react with microspheres in the first step. It was found that the number of reactive carboxyl groups available in copolymeric microspheres is lower compared to number of methacrylic acid units used for polymerization process. Moreover, there is correlation between the number of groups introduced and found to be reactive in microspheres. On the other hand, the number of surface reactive groups was proportional to the number of groups introduced in course of polymerization. Thus, the surface reactive groups can be used as reagent, in novel heterogeneous microtitration procedure, in which a constant number of microspheres of different carboxyl groups contents is introduced to the sample to react with the analyte. The applicability of novel proposed method was tested on the example of Ni(2+) determination. PMID:27474305

  5. Reactivity of 2-ethyl-1-hexanol in the atmosphere.

    PubMed

    Gallego-Iniesta García, María Paz; Moreno Sanroma, Alberto; Martín Porrero, María Pilar; Tapia Valle, Araceli; Cabañas Galán, Beatriz; Salgado Muñoz, María Sagrario

    2010-04-01

    Rate coefficients at room temperature for the reaction of 2-ethyl-1-hexanol with OH and NO(3) radicals and with Cl atoms have been determined in a 150 L PTFE chamber using GC-FID/SPME and FTIR as detection systems. The rate coefficients k (in units of cm(3) molecule(-1) s(-1)) obtained were: (1.13 +/- 0.31) 10(-11) for the OH reaction, (2.93 +/- 0.92) 10(-15) for the NO(3) reaction and (1.88 +/- 0.25) 10(-10) for the Cl reaction. Despite the high concentrations of 2-ethyl-1-hexanol, especially in indoor air, this is the first kinetic study carried out to date for these reactions. The results are consistent with the expected reactivity given the chemical structure of 2-ethyl-1-hexanol. Calculated atmospheric lifetimes reveal that the dominant loss process for 2-ethyl-1-hexanol is clearly the daytime reaction with the hydroxyl radical. PMID:20237722

  6. Reactivity of 2-ethyl-1-hexanol in the atmosphere.

    PubMed

    Gallego-Iniesta García, María Paz; Moreno Sanroma, Alberto; Martín Porrero, María Pilar; Tapia Valle, Araceli; Cabañas Galán, Beatriz; Salgado Muñoz, María Sagrario

    2010-04-01

    Rate coefficients at room temperature for the reaction of 2-ethyl-1-hexanol with OH and NO(3) radicals and with Cl atoms have been determined in a 150 L PTFE chamber using GC-FID/SPME and FTIR as detection systems. The rate coefficients k (in units of cm(3) molecule(-1) s(-1)) obtained were: (1.13 +/- 0.31) 10(-11) for the OH reaction, (2.93 +/- 0.92) 10(-15) for the NO(3) reaction and (1.88 +/- 0.25) 10(-10) for the Cl reaction. Despite the high concentrations of 2-ethyl-1-hexanol, especially in indoor air, this is the first kinetic study carried out to date for these reactions. The results are consistent with the expected reactivity given the chemical structure of 2-ethyl-1-hexanol. Calculated atmospheric lifetimes reveal that the dominant loss process for 2-ethyl-1-hexanol is clearly the daytime reaction with the hydroxyl radical.

  7. Fragrance material review on 2-ethyl-1-butanol.

    PubMed

    McGinty, D; Letizia, C S; Api, A M

    2010-07-01

    A toxicologic and dermatologic review of 2-ethyl-1-butanol when used as a fragrance ingredient is presented. 2-Ethyl-1-butanol is a member of the fragrance structural group branched chain saturated alcohols. The common characteristic structural elements of the alcohols with saturated branched chain are one hydroxyl group per molecule, and a C(4)-C(12) carbon chain with one or several methyl side chains. This review contains a detailed summary of all available toxicology and dermatology papers that are related to this individual fragrance ingredient and is not intended as a stand-alone document. A safety assessment of the entire branched chain saturated alcohol group will be published simultaneously with this document; please refer to Belsito et al. (2010) for an overall assessment of the safe use of this material and all other branched chain saturated alcohols in fragrances.

  8. Fragrance material review on 2-ethyl-1-hexanol.

    PubMed

    McGinty, D; Scognamiglio, J; Letizia, C S; Api, A M

    2010-07-01

    A summary of the safety data available for 2-ethyl-1-hexanol when used as a fragrance ingredient is presented. 2-Ethyl-1-hexanol is a member of the fragrance structural group branched chain saturated alcohols in which the common characteristic structural element is one hydroxyl group per molecule, and a C(4) to C(12) carbon chain with one or several methyl side chains. This review contains a detailed summary of all available toxicology and dermatology papers that are related to this individual fragrance ingredient and is not intended as a stand-alone document. A safety assessment of the entire branched chain saturated alcohol group will be published simultaneously with this document; please refer to Belsito et al. (2010) for an overall assessment of the safe use of this material and all other branched chain saturated alcohols in fragrances.

  9. Fragrance material review on 2-ethyl-1-hexanol.

    PubMed

    McGinty, D; Scognamiglio, J; Letizia, C S; Api, A M

    2010-07-01

    A summary of the safety data available for 2-ethyl-1-hexanol when used as a fragrance ingredient is presented. 2-Ethyl-1-hexanol is a member of the fragrance structural group branched chain saturated alcohols in which the common characteristic structural element is one hydroxyl group per molecule, and a C(4) to C(12) carbon chain with one or several methyl side chains. This review contains a detailed summary of all available toxicology and dermatology papers that are related to this individual fragrance ingredient and is not intended as a stand-alone document. A safety assessment of the entire branched chain saturated alcohol group will be published simultaneously with this document; please refer to Belsito et al. (2010) for an overall assessment of the safe use of this material and all other branched chain saturated alcohols in fragrances. PMID:20659633

  10. Fragrance material review on 2-ethyl-1-butanol.

    PubMed

    McGinty, D; Letizia, C S; Api, A M

    2010-07-01

    A toxicologic and dermatologic review of 2-ethyl-1-butanol when used as a fragrance ingredient is presented. 2-Ethyl-1-butanol is a member of the fragrance structural group branched chain saturated alcohols. The common characteristic structural elements of the alcohols with saturated branched chain are one hydroxyl group per molecule, and a C(4)-C(12) carbon chain with one or several methyl side chains. This review contains a detailed summary of all available toxicology and dermatology papers that are related to this individual fragrance ingredient and is not intended as a stand-alone document. A safety assessment of the entire branched chain saturated alcohol group will be published simultaneously with this document; please refer to Belsito et al. (2010) for an overall assessment of the safe use of this material and all other branched chain saturated alcohols in fragrances. PMID:20659644

  11. Acrylic acid

    Integrated Risk Information System (IRIS)

    Acrylic acid ( CASRN 79 - 10 - 7 ) Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogenic Eff

  12. Methyl acrylate

    Integrated Risk Information System (IRIS)

    Methyl acrylate ; CASRN 96 - 33 - 3 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogenic Ef

  13. Features of the Thermodynamics of Trivalent Lanthanide/Actinide Distribution Reactions by Tri-n-Octylphosphine Oxide and Bis(2-EthylHexyl) Phosphoric Acid

    SciTech Connect

    Travis S. Grimes; Peter R. Zalupski

    2014-11-01

    A new methodology has been developed to study the thermochemical features of the biphasic transfer reactions of trisnitrato complexes of lanthanides and americium by a mono-functional solvating ligand (tri-n-octyl phosphine oxide - TOPO). Stability constants for successive nitrato complexes (M(NO3)x3-x (aq) where M is Eu3+, Am3+ or Cm3+) were determined to assist in the calculation of the extraction constant, Kex, for the metal ions under study. Enthalpies of extraction (?Hextr) for the lanthanide series (excluding Pm3+) and Am3+ by TOPO have been measured using isothermal titration calorimetry. The observed ?Hextr were found to be constant at ~29 kJ mol-1across the series from La3+-Er3+, with a slight decrease observed from Tm3+-Lu3+. These heats were found to be consistent with enthalpies determined using van ’t Hoff analysis of temperature dependent extraction studies. A complete set of thermodynamic parameters (?G, ?H, ?S) was calculated for Eu(NO3)3, Am(NO3)3 and Cm(NO3)3 extraction by TOPO and Am3+ and Cm3+ extraction by bis(2-ethylhexyl) phosphoric acid (HDEHP). A discussion comparing the energetics of these systems is offered. The measured biphasic extraction heats for the transplutonium elements, ?Hextr, presented in these studies are the first ever direct measurements offered using two-phase calorimetric techniques.

  14. Degradation of di(2-ethyl hexyl) phthalate by Fusarium culmorum: Kinetics, enzymatic activities and biodegradation pathway based on quantum chemical modelingpathway based on quantum chemical modeling.

    PubMed

    Ahuactzin-Pérez, Miriam; Tlecuitl-Beristain, Saúl; García-Dávila, Jorge; González-Pérez, Manuel; Gutiérrez-Ruíz, María Concepción; Sánchez, Carmen

    2016-10-01

    Di(2-ethylhexyl) phthalate (DEHP) is a plasticizer widely used in the manufacture of plastics, and it is an environmental contaminant. The specific growth rate (μ), maximum biomass (Xmax), biodegradation constant of DEHP (k), half-life (t1/2) of DEHP biodegradation and removal efficiency of DEHP, esterase and laccase specific activities, and enzymatic yield parameters were evaluated for Fusarium culmorum grown on media containing glucose and different concentrations of DEHP (0, 500 and 1000mg/L). The greatest μ and the largest Xmax occurred in media supplemented with 1000mg of DEHP/L. F. culmorum degraded 95% of the highest amount of DEHP tested (1000mg/L) within 60h of growth. The k and t1/2 were 0.024h(-1) and 28h, respectively, for both DEHP concentrations. The removal efficiency of DEHP was 99.8% and 99.9% for 1000 and 500mg/L, respectively. Much higher specific esterase activity than specific laccase activity was observed in all media tested. The compounds of biodegradation of DEHP were identified by GC-MS. A DEHP biodegradation pathway by F. culmorum was proposed on the basis of the intermolecular flow of electrons of the identified intermediate compounds using quantum chemical modeling. DEHP was fully metabolized by F. culmorum with butanediol as the final product. This fungus offers great potential in bioremediation of environments polluted with DEHP.

  15. Fragrance material review on methyl hexyl oxo cyclopentanone carboxylate.

    PubMed

    Scognamiglio, J; Jones, L; Letizia, C S; Api, A M

    2012-10-01

    A toxicologic and dermatologic review of methyl hexyl oxo cyclopentanone carboxylate when used as a fragrance ingredient is presented. Methyl hexyl oxo cyclopentanone carboxylate is a member of the fragrance structural group ketones cyclopentanones and cyclopentenones. The common characteristic structural element of the group members is a cyclopentanone or cyclopentenone ring with a straight or branched chain alkane or alkene substituent. This review contains a detailed summary of all available toxicology and dermatology papers that are related to this individual fragrance ingredient and is not intended as a stand-alone document. Available data for methyl hexyl oxo cyclopentanone carboxylate were evaluated then summarized and includes physical properties, acute toxicity, skin irritation, skin sensitization, and genotoxicity data. A safety assessment of the entire ketones cyclopentanones and cyclopentenones will be published simultaneously with this document; please refer to Belsito et al. (this issue) for an overall assessment of the safe use of this material and all ketones cyclopentanones and cyclopentenones in fragrances.

  16. Hexyl-nicotinate-induced vasodilation in normal human skin.

    PubMed

    Dowd, P M; Whitefield, M; Greaves, M W

    1987-01-01

    Hexyl nicotinate in a lotion formulation was applied topically to the skin of 10 healthy volunteers with clinically normal skin. Erythematous responses were assessed visually and skin blood flow determined by means of a laser Doppler flow meter which measures the blood cell flux (Pf2 Perimed, Sweden). Mean erythematous responses and increased blood cell flux were dose-related but in several subjects increases in blood flow occurred in the presence of barely detectable erythematous responses. In some subjects, hexyl nicotinate may be an effective cutaneous vasodilator even in the presence of minimal erythema.

  17. Capillary gas chromatographic determination of cyclohexanone and 2-ethyl-1-hexanol leached from solution administration sets.

    PubMed

    Danielson, J W

    1991-01-01

    A capillary gas chromatographic method is described for the determination of cyclohexanone and 2-ethyl-1-hexanol leached from solution administration sets. A preliminary study was made of compounds leached from solution administration sets by 5% sodium bicarbonate solution (pH 8.1), 0.9% sodium chloride solution (pH 6.8), and water. Water was selected as the leaching solvent because similar quantities of the compounds were leached into water and into both types of parenteral solutions. The correlation coefficients were 0.99977 for cyclohexanone and 0.99974 for 2-ethyl-1-hexanol, and recoveries were good (93-94%). Five administration sets from each of 2 manufacturers were analyzed by this method. The amounts of cyclohexanone that were leached from the individual sets varied considerably; however, similar quantities were leached from sets of both manufacturers. 2-Ethyl-1-hexanol was also found in extracts from each of the sets analyzed.

  18. 40 CFR 721.4468 - 1H-Imidazole, 2-ethyl-4,5-dihydro-4-methyl-.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false 1H-Imidazole, 2-ethyl-4,5-dihydro-4... Specific Chemical Substances § 721.4468 1H-Imidazole, 2-ethyl-4,5-dihydro-4-methyl-. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as...

  19. 40 CFR 721.4468 - 1H-Imidazole, 2-ethyl-4,5-dihydro-4-methyl-.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false 1H-Imidazole, 2-ethyl-4,5-dihydro-4... Specific Chemical Substances § 721.4468 1H-Imidazole, 2-ethyl-4,5-dihydro-4-methyl-. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as...

  20. 40 CFR 721.4468 - 1H-Imidazole, 2-ethyl-4,5-dihydro-4-methyl-.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false 1H-Imidazole, 2-ethyl-4,5-dihydro-4... Specific Chemical Substances § 721.4468 1H-Imidazole, 2-ethyl-4,5-dihydro-4-methyl-. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as...

  1. 40 CFR 721.4468 - 1H-Imidazole, 2-ethyl-4,5-dihydro-4-methyl-.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false 1H-Imidazole, 2-ethyl-4,5-dihydro-4... Specific Chemical Substances § 721.4468 1H-Imidazole, 2-ethyl-4,5-dihydro-4-methyl-. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as...

  2. 40 CFR 721.4468 - 1H-Imidazole, 2-ethyl-4,5-dihydro-4-methyl-.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false 1H-Imidazole, 2-ethyl-4,5-dihydro-4... Specific Chemical Substances § 721.4468 1H-Imidazole, 2-ethyl-4,5-dihydro-4-methyl-. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as...

  3. Acrylate Systemic Contact Dermatitis.

    PubMed

    Sauder, Maxwell B; Pratt, Melanie D

    2015-01-01

    Acrylates, the 2012 American Contact Dermatitis Society allergen of the year, are found in a range of products including the absorbent materials within feminine hygiene pads. When fully polymerized, acrylates are nonimmunogenic; however, if not completely cured, the monomers can be potent allergens.A 28-year-old woman is presented, who had her teeth varnished with Isodan (Septodont, Saint-Maur-des-Fossés, France) containing HEMA (2-hydroxyethyl methacrylate) with no initial reaction. Approximately 1 month later, the patient developed a genital dermatitis secondary to her feminine hygiene pads. The initial reaction resolved, but 5 months later, the patient developed a systemic contact dermatitis after receiving a second varnishing.The patient was dramatically patch test positive to many acrylates. This case demonstrates a reaction to likely unpolymerized acrylates within a feminine hygiene pad, as well as broad cross-reactivity or cosensitivity to acrylates, and possibly a systemic contact dermatitis with systemic re-exposure to unpolymerized acrylates.

  4. 40 CFR 721.5500 - 7-Oxabicyclo[4.1.0]heptane, 3-ethenyl, homopolymer, ether with 2-ethyl-2-(hydroxymethyl)-1,3-pro...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., homopolymer, ether with 2-ethyl-2-(hydroxymethyl)-1,3-pro-pane-diol (3:1), epoxidized. 721.5500 Section 721...-Oxabicyclo heptane, 3-ethenyl, homopolymer, ether with 2-ethyl-2-(hydroxymethyl)-1,3-pro-pane-diol (3:1... 7-oxabicyclo heptane, 3-ethenyl, homopolymer, ether with 2-ethyl-2(hydroxymethyl)-1,3-propanediol...

  5. 40 CFR 721.5500 - 7-Oxabicyclo[4.1.0]heptane, 3-ethenyl, homopolymer, ether with 2-ethyl-2-(hydroxymethyl)-1,3-pro...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ..., homopolymer, ether with 2-ethyl-2-(hydroxymethyl)-1,3-pro-pane-diol (3:1), epoxidized. 721.5500 Section 721...-Oxabicyclo heptane, 3-ethenyl, homopolymer, ether with 2-ethyl-2-(hydroxymethyl)-1,3-pro-pane-diol (3:1... 7-oxabicyclo heptane, 3-ethenyl, homopolymer, ether with 2-ethyl-2(hydroxymethyl)-1,3-propanediol...

  6. Acute effects of exposure to 1 mg/m(3) of vaporized 2-ethyl-1-hexanol in humans.

    PubMed

    Ernstgård, L; Norbäck, D; Nordquist, T; Wieslander, G; Wålinder, R; Johanson, G

    2010-04-01

    The objective was to assess acute effects from controlled exposure of volunteers to 2-ethyl-1-hexanol, a volatile organic compound that is often found in indoor air. Sixteen males and fourteen females were in random order exposed to 1 mg/m(3) of vapors of 2-ethyl-1-hexanol or to clean air (control exposure) in an exposure chamber during 2 h at rest. The subjects performed symptom ratings on Visual Analog Scales. During exposure to 2-ethyl-1-hexanol subjective ratings of smell and eye discomfort were minimally but significantly increased. Ratings of nasal irritation, throat irritation, headache, dyspnoea, fatigue, dizziness, nausea, and intoxication were not significantly affected. No exposure-related effects on measurement of blinking frequency by electromyography, measurement of the eye break-up time, vital staining of the eye, nasal lavage biomarkers, transfer tests, spirometric and rhinometric measures were seen. No differences in response were seen between sexes or between atopics and non-atopics. Practical Implications It is important to assess acute effects in volatile organic compounds like 2-ethyl-1-hexanol. 2-ethyl-1-hexanol is often found in indoor air generated by degradation of plastic building materials or in new buildings. There are associations between 2-ethyl-1-hexanol in indoor air and respiratory effects, eye irritation, headache, and blurred vision. A controlled chamber exposure study in acute effects was performed. In conclusion, this study showed weak subjective symptom of irritation in the eyes. PMID:20409194

  7. Evaluation of liquid-liquid extraction process for separating acrylic acid produced from renewable sugars.

    PubMed

    Alvarez, M E T; Moraes, E B; Machado, A B; Maciel Filho, R; Wolf-Maciel, M R

    2007-04-01

    In this article, the separation and the purification of the acrylic acid produced from renewable sugars were studied using the liquid-liquid extraction process. Nonrandom two-liquids and universal quasi-chemical models and the prediction method universal quasi-chemical functional activity coefficients were used for generating liquid-liquid equilibrium diagrams for systems made up of acrylic acid, water, and solvents (diisopropyl ether, isopropyl acetate, 2-ethyl hexanol, and methyl isobutyl ketone) and the results were compared with available liquid-liquid equilibrium experimental data. Aspen Plus (Aspen Technology, Inc., version 2004.1) software was used for equilibrium and process calculations. High concentration of acrylic acid was obtained in this article using diisopropyl ether as solvent.

  8. Acrylic vessel cleaning tests

    SciTech Connect

    Earle, D.; Hahn, R.L.; Boger, J.; Bonvin, E.

    1997-02-26

    The acrylic vessel as constructed is dirty. The dirt includes blue tape, Al tape, grease pencil, gemak, the glue or residue form these tapes, finger prints and dust of an unknown composition but probably mostly acrylic dust. This dirt has to be removed and once removed, the vessel has to be kept clean or at least to be easily cleanable at some future stage when access becomes much more difficult. The authors report on the results of a series of tests designed: (a) to prepare typical dirty samples of acrylic; (b) to remove dirt stuck to the acrylic surface; and (c) to measure the optical quality and Th concentration after cleaning. Specifications of the vessel call for very low levels of Th which could come from tape residues, the grease pencil, or other sources of dirt. This report does not address the concerns of how to keep the vessel clean after an initial cleaning and during the removal of the scaffolding. Alconox is recommended as the cleaner of choice. This acrylic vessel will be used in the Sudbury Neutrino Observatory.

  9. Acrylic purification and coatings

    NASA Astrophysics Data System (ADS)

    Kuźniak, Marcin

    2011-04-01

    Radon (Rn) and its decay daughters are a well-known source of background in direct WIMP detection experiments, as either a Rn decay daughter or an alpha particle emitted from a thin inner surface layer of a detector could produce a WIMP-like signal. Different surface treatment and cleaning techniques have been employed in the past to remove this type of contamination. A new method of dealing with the problem has been proposed and used for a prototype acrylic DEAP-1 detector. Inner surfaces of the detector were coated with a layer of ultra pure acrylic, meant to shield the active volume from alphas and recoiling nuclei. An acrylic purification technique and two coating techniques are described: a solvent-borne (tested on DEAP-1) and solvent-less (being developed for the full scale DEAP-3600 detector).

  10. Acrylic purification and coatings

    SciTech Connect

    Kuzniak, Marcin

    2011-04-27

    Radon (Rn) and its decay daughters are a well-known source of background in direct WIMP detection experiments, as either a Rn decay daughter or an alpha particle emitted from a thin inner surface layer of a detector could produce a WIMP-like signal. Different surface treatment and cleaning techniques have been employed in the past to remove this type of contamination. A new method of dealing with the problem has been proposed and used for a prototype acrylic DEAP-1 detector. Inner surfaces of the detector were coated with a layer of ultra pure acrylic, meant to shield the active volume from alphas and recoiling nuclei. An acrylic purification technique and two coating techniques are described: a solvent-borne (tested on DEAP-1) and solvent-less (being developed for the full scale DEAP-3600 detector).

  11. Acrylic mechanical bond tests

    SciTech Connect

    Wouters, J.M.; Doe, P.J.

    1991-02-01

    The tensile strength of bonded acrylic is tested as a function of bond joint thickness. 0.125 in. thick bond joints were found to posses the maximum strength while the acceptable range of joints varied from 0.063 in. to almost 0.25 in. Such joints are used in the Sudbury Neutrino Observatory.

  12. Identification of cyclopropaneoctanoic acid 2-hexyl in human adipose tissue and serum.

    PubMed

    Sledzinski, Tomasz; Mika, Adriana; Stepnowski, Piotr; Proczko-Markuszewska, Monika; Kaska, Lukasz; Stefaniak, Tomasz; Swierczynski, Julian

    2013-08-01

    Fatty acids containing a cyclopropane ring in their structure (cyclopropane FA) have been found in a wide variety of bacteria, a number of protozoa, and Myriapoda. Little is known about cyclopropane FA in mammal, especially in human tissues. The present study deals with the identification of cyclopropane FA in adipose tissue and serum of humans and rats. Fatty acids extracted from the adipose tissue and serum obtained from obese women during bariatric surgery were methylated and analyzed on GC-MS. We have identified: cyclopropaneoctanoic acid 2-hexyl, cyclopropaneoctanoic acid 2-octyl, cyclopropanenonanoic acid, and 2-[[2-[(2-ethylcyclopropyl)methyl]cyclopropyl]methyl] acid in human adipose tissue. We confirmed the presence of cyclopropaneoctanoic acid 2-hexyl by derivatization of FA extracted from human adipose tissue to picolinyl esters. Cyclopropaneoctanoic acid 2-hexyl was the main cyclopropane FA (approximately 0.4 % of total fatty acids in human adipose tissue, and about 0.2 % of total fatty acids in the serum). In adipose tissue cyclopropaneoctanoic acid 2-hexyl was found mainly in triacylglycerols, whereas in serum in phospholipids and triacylglycerols. The cyclopropaneoctanoic acid 2-hexyl has also been found in serum, and adipose tissue of rats in amounts comparable to humans. The content of cyclopropaneoctanoic acid 2-hexyl decreased in adipose tissue of rats maintained on a restricted diet for 1 month. In conclusion, we demonstrated that cyclopropaneoctanoic acid 2-hexyl is present in human adipose tissue and serum. Adipose tissue cyclopropaneoctanoic acid 2-hexyl is stored mainly in triacylglycerols and the storage of this cyclopropane FA is affected by food restriction.

  13. A novel collector 2-ethyl-2-hexenoic hydroxamic acid: Flotation performance and adsorption mechanism to ilmenite

    NASA Astrophysics Data System (ADS)

    Xu, Haifeng; Zhong, Hong; Tang, Qing; Wang, Shuai; Zhao, Gang; Liu, Guangyi

    2015-10-01

    In this paper, a novel collector, 2-ethyl-2-hexenoic hydroxamic acid (EHHA) was prepared and characterized by elemental analysis, infrared, 1H NMR, 13C NMR and mass spectra. The flotation performance and adsorption mechanism of EHHA to ilmenite were investigated by micro-flotation tests, density functional theory (DFT) calculations, FTIR spectra, zeta potential and solution chemistry analyses. The micro-flotation results indicated that EHHA exhibited superior flotation performance compared to isooctyl hydroximic acid (IOHA) and octyl hydroxamic acid (OHA), and floated out 84.03% ilmenite at pH 8.0 with 250 mg/L dosage. The analyses of FTIR spectra and zeta potential demonstrated that EHHA might chemisorb onto ilmenite surfaces by form of five-membered chelates. The solution chemistry analyses further inferred that at pH 6.3-10.5, both Fe and Ti species on ilmenite surfaces could chelate EHHA. DFT calculation results implied EHHA owned the strongest affinity to ilmenite among the three C8 hydroximic acids. To discern the sharply improving floatability of ilmenite at pH 8-10, a schematic co-adsorption molecule-ion model of EHHA on ilmenite surfaces was suggested.

  14. Dielectric relaxation of 2-ethyl-1-hexanol around the glass transition by thermally stimulated depolarization currents.

    PubMed

    Arrese-Igor, S; Alegría, A; Colmenero, J

    2015-06-01

    We explore new routes for characterizing the Debye-like and α relaxation in 2-ethyl-1-hexanol (2E1H) monoalcohol by using low frequency dielectric techniques including thermally stimulated depolarization current (TSDC) techniques and isothermal depolarization current methods. In this way, we have improved the resolution of the overlapped processes making it possible the analysis of the data in terms of a mode composition as expected for a chain-like response. Furthermore the explored ultralow frequencies enabled to study dynamics at relatively low temperatures close to the glass transition (Tg). Results show, on the one hand, that Debye-like and α relaxation timescales dramatically approach to each other upon decreasing temperature to Tg. On the other hand, the analysis of partial polarization TSDC data confirms the single exponential character of the Debye-like relaxation in 2E1H and rules out the presence of Rouse type modes in the scenario of a chain-like response. Finally, on crossing the glass transition, the Debye-like relaxation shows non-equilibrium effects which are further emphasized by aging treatment and would presumably emerge as a result of the arrest of the structural relaxation below Tg. PMID:26049505

  15. Structure and Proton Conductivity in Mixtures of Poly(acrylic acid) and Imidazole

    NASA Astrophysics Data System (ADS)

    Yang, Han-Chang; Griffin, Philip J.; Winey, Karen I.; University of Pennsylvania Team

    2015-03-01

    Proton conductivity in polymer electrolyte membranes (PEMs) typically involves water, which requires that during operation the humidity of the PEM be carefully controlled. In contrast, anhydrous protic polymer membranes promote proton transport by incorporating heterocyclic molecules, such as imidazole and its derivatives, into acid-containing polymers. In this work, we explore the interplay between nanoscale-structure and proton conduction of poly(acrylic acid) (PAA) blended at varying compositions with 2-ethyl-4-methylimidazole (EMI). We present the glass transition temperature from differential scanning calorimetry, morphology characterization from X-ray scattering, and proton conductivity from electrical impedance spectroscopy.

  16. [Actions of new iminium compounds against bacteria and fungi. 30. 3-alkoxymethyl-1-hexyl-, 3-alkylthiomethyl-1-hexyl-, 3-alkoxymethyl-1-octyl- and 3-alkylthiomethyl-1-octylbenzimidazolium chlorides].

    PubMed

    Pernak, J; Skrzypczak, A; Krysiński, J; Kaźmierczak, M; Jedraszczyk, J; Michalak, L

    1994-02-01

    Syntheses and antimicrobial activity of the title compounds are described. They were obtained by reaction of 1-hexyl- or 1-octylbenzimidazol with chloromethylalkyl ether or chloromethylalkyl sulfide. The antibacterial properties were tested on 13 strains of bacteria and fungi. The best antibacterial activity was exhibited by chlorides with octylthiomethyl and decyloxymethyl groups. PMID:8135642

  17. 40 CFR 721.10505 - Phosphoric acid, mixed mono- and diesters with 2-ethyl-1-hexanol and polyethylene glycol mono-C12...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Phosphoric acid, mixed mono- and... Phosphoric acid, mixed mono- and diesters with 2-ethyl-1-hexanol and polyethylene glycol mono-C12-16-alkyl... identified as phosphoric acid, mixed mono- and diesters with 2-ethyl-1-hexanol and polyethylene glycol...

  18. 40 CFR 721.10505 - Phosphoric acid, mixed mono- and diesters with 2-ethyl-1-hexanol and polyethylene glycol mono-C12...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Phosphoric acid, mixed mono- and... Phosphoric acid, mixed mono- and diesters with 2-ethyl-1-hexanol and polyethylene glycol mono-C12-16-alkyl... identified as phosphoric acid, mixed mono- and diesters with 2-ethyl-1-hexanol and polyethylene glycol...

  19. 21 CFR 177.1010 - Acrylic and modified acrylic plastics, semirigid and rigid.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Acrylic and modified acrylic plastics, semirigid... Acrylic and modified acrylic plastics, semirigid and rigid. Semirigid and rigid acrylic and modified acrylic plastics may be safely used as articles intended for use in contact with food, in accordance...

  20. 21 CFR 177.1010 - Acrylic and modified acrylic plastics, semirigid and rigid.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Acrylic and modified acrylic plastics, semirigid... Acrylic and modified acrylic plastics, semirigid and rigid. Semirigid and rigid acrylic and modified acrylic plastics may be safely used as articles intended for use in contact with food, in accordance...

  1. 21 CFR 177.1010 - Acrylic and modified acrylic plastics, semirigid and rigid.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Acrylic and modified acrylic plastics, semirigid... Acrylic and modified acrylic plastics, semirigid and rigid. Semirigid and rigid acrylic and modified acrylic plastics may be safely used as articles intended for use in contact with food, in accordance...

  2. Products of the OH radical-initiated reactions of 2- and 3-hexyl nitrate

    NASA Astrophysics Data System (ADS)

    Aschmann, Sara M.; Arey, Janet; Atkinson, Roger

    2012-01-01

    Products of the gas-phase reaction of OH radicals with 2-hexyl nitrate (containing 13% 3-hexyl nitrate) have been investigated by gas chromatography with mass spectral and flame ionization detection, and by direct air sampling atmospheric pressure ionization tandem mass spectrometry. The products identified and quantified from 2-hexyl nitrate were: 2-hexanone (8.6 ± 1.3%), propanal (3.4 ± 0.8%), butanal (2.3 ± 0.6%) and 5-hydroxy-2-hexanone (25%), where the molar yields are given in parentheses. 3-Hexanone was observed from the 3-hexyl nitrate reaction, with a molar formation yield of 9.5 ± 2.1%. Organic nitrates of molecular weight 133, 161, 177 and 208 were also observed, and these are attributed to C 4-carbonyl nitrate(s), C 6-carbonyl-nitrates, C 6-hydroxycarbonyl-nitrates and C 6-dinitrates, respectively, and are expected to account for all or most of the non-quantified reaction products from OH + 2- and 3-hexyl nitrate. 5-Hydroxy-2-hexanone formation indicates that the CH 3CH(ONO 2)CH 2CH 2CH(O rad )CH 3 alkoxy radical dominantly reacts by isomerization.

  3. Optimisation of n-Hexyl Acetate Synthesis in a Chromatographic Reactor

    NASA Astrophysics Data System (ADS)

    Patel, Dipesh; Saha, Basudeb; Wakeman, Richard

    Laboratory scale batch chromatographic reactor experiments were carried for the esterification of acetic acid with n-hexanol to synthesise a value added ester, namely n-hexyl acetate in the presence of an ion exchange resin catalyst, Purolite CT-124. The effect of various parameters such as solvent flow rates in the regeneration step, amount of reactants in the reaction step and reaction step time was studied for optimisation of the reaction condition in a batch chromatographic reactor. This information would be useful for the design, operation and optimisation of n-hexyl acetate synthesis in a continuous chromatographic reactor.

  4. 40 CFR 721.304 - Acetic acid, [(5-chloro-8-quinolinyl)oxy-], 1-methyl hexyl ester.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Acetic acid, , 1-methyl hexyl ester... Substances § 721.304 Acetic acid, , 1-methyl hexyl ester. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as acetic acid, -, 1-methylhexyl ester (PMN...

  5. 40 CFR 721.304 - Acetic acid, [(5-chloro-8-quinolinyl)oxy-], 1-methyl hexyl ester.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Acetic acid, , 1-methyl hexyl ester... Substances § 721.304 Acetic acid, , 1-methyl hexyl ester. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as acetic acid, -, 1-methylhexyl ester (PMN...

  6. 40 CFR 721.304 - Acetic acid, [(5-chloro-8-quinolinyl)oxy-], 1-methyl hexyl ester.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Acetic acid, , 1-methyl hexyl ester... Substances § 721.304 Acetic acid, , 1-methyl hexyl ester. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as acetic acid, -, 1-methylhexyl ester (PMN...

  7. 40 CFR 721.304 - Acetic acid, [(5-chloro-8-quinolinyl)oxy-], 1-methyl hexyl ester.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Acetic acid, , 1-methyl hexyl ester... Substances § 721.304 Acetic acid, , 1-methyl hexyl ester. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as acetic acid, -, 1-methylhexyl ester (PMN...

  8. [Acrylic resin removable partial dentures].

    PubMed

    de Baat, C; Witter, D J; Creugers, N H J

    2011-01-01

    An acrylic resin removable partial denture is distinguished from other types of removable partial dentures by an all-acrylic resin base which is, in principle, solely supported by the edentulous regions of the tooth arch and in the maxilla also by the hard palate. When compared to the other types of removable partial dentures, the acrylic resin removable partial denture has 3 favourable aspects: the economic aspect, its aesthetic quality and the ease with which it can be extended and adjusted. Disadvantages are an increased risk of caries developing, gingivitis, periodontal disease, denture stomatitis, alveolar bone reduction, tooth migration, triggering of the gag reflex and damage to the acrylic resin base. Present-day indications are ofa temporary or palliative nature or are motivated by economic factors. Special varieties of the acrylic resin removable partial denture are the spoon denture, the flexible denture fabricated of non-rigid acrylic resin, and the two-piece sectional denture. Furthermore, acrylic resin removable partial dentures can be supplied with clasps or reinforced by fibers or metal wires.

  9. The microwave spectrum of n-hexyl acetate and structural aspects of n-alkyl acetates

    NASA Astrophysics Data System (ADS)

    Attig, T.; Kannengießer, R.; Kleiner, I.; Stahl, W.

    2014-04-01

    The microwave spectrum of n-hexyl acetate was recorded in the range of 10-13.5 GHz using the Aachen MB-FTMW spectrometer. The rotational constants of the most abundant conformer were determined to be A = 3.3591100(32) GHz, B = 0.39596553(53) GHz, and C = 0.36999804(31) GHz. Quantum chemical calculations for specific conformers were carried out at the MP2/6-311++G(d,p) level. The programs XIAM and BELGI were used to analyze the internal rotation of the acetyl methyl group. The observed conformer of n-hexyl acetate was compared to the lowest energy conformers of n-butyl acetate and n-pentyl acetate.

  10. Crystal structure of cyclo­hexyl­ammonium thio­cyanate

    PubMed Central

    Bagabas, Abdulaziz A.; Alhoshan, Sultan B.; Ghabbour, Hazem A.; Chidan Kumar, C. S.; Fun, Hoong-Kun

    2015-01-01

    In the title salt, C6H11NH3 +·SCN−, the cyclo­hexyl­ammonium ring adopts a slightly distorted chair conformation. The ammonium group occupies an equatorial position to minimize 1,3 and 1,5 diaxial inter­actions. In the crystal, the components are linked by N—H⋯N and N—H⋯S hydrogen-bonding inter­actions, resulting in a three-dimensional network. PMID:25705511

  11. Dopant effects on 2-ethyl-1-hexanol: A dual-channel impedance spectroscopy and neutron scattering study

    NASA Astrophysics Data System (ADS)

    Singh, Lokendra P.; Raihane, Ahmed; Alba-Simionesco, Christiane; Richert, Ranko

    2015-01-01

    A two-channel impedance technique has been used to study the relaxation behavior of 2-ethyl-1-hexanol with polar and non-polar dopants at the few percent concentration level over a wide temperature and frequency range. The non-polar dopants shift both the Debye and the primary structural relaxation time in the same direction, to shorter times for 3-methylpentane and to longer times for squalane, consistent with the relative glass transition temperatures (Tg) of the components. By contrast, polar dopants such as water or methanol modify the α-process towards slower dynamics and increased amplitude, while the Debye process is accelerated and with a decreased amplitude. This effect of adding water to alcohol is explained by water promoting more compact structures with reduced Kirkwood correlation factors. This picture is consistent with a shift in the neutron scattering pre-peak to lower scattering vectors and with simulation work on alcohol-water systems.

  12. Dopant effects on 2-ethyl-1-hexanol: a dual-channel impedance spectroscopy and neutron scattering study.

    PubMed

    Singh, Lokendra P; Raihane, Ahmed; Alba-Simionesco, Christiane; Richert, Ranko

    2015-01-01

    A two-channel impedance technique has been used to study the relaxation behavior of 2-ethyl-1-hexanol with polar and non-polar dopants at the few percent concentration level over a wide temperature and frequency range. The non-polar dopants shift both the Debye and the primary structural relaxation time in the same direction, to shorter times for 3-methylpentane and to longer times for squalane, consistent with the relative glass transition temperatures (Tg) of the components. By contrast, polar dopants such as water or methanol modify the α-process towards slower dynamics and increased amplitude, while the Debye process is accelerated and with a decreased amplitude. This effect of adding water to alcohol is explained by water promoting more compact structures with reduced Kirkwood correlation factors. This picture is consistent with a shift in the neutron scattering pre-peak to lower scattering vectors and with simulation work on alcohol-water systems.

  13. Dopant effects on 2-ethyl-1-hexanol: A dual-channel impedance spectroscopy and neutron scattering study

    SciTech Connect

    Singh, Lokendra P.; Richert, Ranko; Raihane, Ahmed; Alba-Simionesco, Christiane

    2015-01-07

    A two-channel impedance technique has been used to study the relaxation behavior of 2-ethyl-1-hexanol with polar and non-polar dopants at the few percent concentration level over a wide temperature and frequency range. The non-polar dopants shift both the Debye and the primary structural relaxation time in the same direction, to shorter times for 3-methylpentane and to longer times for squalane, consistent with the relative glass transition temperatures (T{sub g}) of the components. By contrast, polar dopants such as water or methanol modify the α-process towards slower dynamics and increased amplitude, while the Debye process is accelerated and with a decreased amplitude. This effect of adding water to alcohol is explained by water promoting more compact structures with reduced Kirkwood correlation factors. This picture is consistent with a shift in the neutron scattering pre-peak to lower scattering vectors and with simulation work on alcohol-water systems.

  14. Bonding auto-polymerising acrylic resin to acrylic denture teeth.

    PubMed

    Nagle, Susan; Ray, Noel J; Burke, Francis M; Gorman, Catherine M

    2009-09-01

    This study investigated the effect of surface treatments on the shear bond strength of an auto-polymerising acrylic resin cured to acrylic denture teeth. The surface treatments included a combination of grit-blasting and/or wetting the surface with monomer. Samples were prepared and then stored in water prior to shear testing. The results indicated that the application of monomer to the surface prior to bonding did not influence the bond strength. Grit blasting was found to significantly increase the bond strength. PMID:19839190

  15. Hexyl decanoate, the first trail pheromone compound identified in a stingless bee, Trigona recursa.

    PubMed

    Jarau, Stefan; Schulz, Claudia M; Hrncir, Michael; Francke, Wittko; Zucchi, Ronaldo; Barth, Friedrich G; Ayasse, Manfred

    2006-07-01

    Foragers of many species of stingless bees guide their nestmates to food sources by means of scent trails deposited on solid substrates between the food and the nest. The corresponding trail pheromones are generally believed to be produced in the mandibular glands, although definitive experimental proof has never been provided. We tested the trail following behavior of recruits of Trigona recursa in field experiments with artificial scent trails branching off from natural scent trails of this stingless bee. First-time recruits (newcomers) did not follow these trails when they were laid with pure solvent or mandibular gland extract. However, they did follow trails made with labial gland extract. Chemical analyses of labial gland secretions revealed that hexyl decanoate was the dominant component (72.4 +/- 1.9% of all volatiles). Newcomers were significantly attracted to artificial trails made with synthetic hexyl decanoate, demonstrating its key function in eliciting scent-following behavior. According to our experiments with T. recursa, the trail pheromone is produced in the labial glands and not in the mandibular glands. Hexyl decanoate is the first component of a trail pheromone identified and proved to be behaviorally active in stingless bees.

  16. [Role of mexidol (2-ethyl-6-methyl-3-hydroxypyridine succinate) in the obtaining of stabilized magnetite nanoparticles for biomedical application].

    PubMed

    Vazhnichaya, Ye M; Mokliak, Ye V; Kurapov, Yu A; Zabozlaev, A A

    2015-01-01

    Magnetite nanoparticles (NPs) are studied as agents for magnetic resonance imaging, hyperthermia of malignant tumors, targeted drug delivery as well as anti-anemic action. One of the main problems of such NPs is their aggregation that requires creation of methods for magnetite NPs stabilization during preparation of liquid medicinal forms on their basis. The present work is devoted to the possibility of mexidol (2-ethyl-6-methyl-3-hydroxypyridine succinate) use for solubilization of magnetite NPs in hydrophilic medium. For this purpose, the condensate produced by electron-beam evaporation and condensation, with magnetite particles of size 5-8 nm deposited into the crystals of sodium chloride were used in conjunction with substance of mexidol (2-ethyl-6-methyl-3-hydroxypyridine succinate), and low molecular weight polyvinylpyrrolidone (PVP). The NP condensate was dispersed in distilled water or PVP or mexidol solutions. NPs size distribution in the liquid phase of the systems was determined by photon correlation spectroscopy, iron (Fe) concentration was evaluated by atomic emission spectrometry. It is shown that in the dispersion prepared in distilled water, the major amount of NPs was of 13-120 nm in size, in mexidol solution - 270-1700 nm, in PVP solution - 30-900 nm. In the fluid containing magnetite NPs together with mexidol and PVP, the main fraction (99.9%) was characterized by the NPs size of 14-75 nm with maximum of 25 nm. This system had the highest iron concentration: it was similar to that in the sample with mexidol solution and 6.6-7.3 times higher than the concentration in the samples with distilled water or PVP. Thus, in the preparation of aqueous dispersions based on magnetite NPs condensate, mexidol provides a transition of Fe to the liquid phase in amount necessary to achieve its biological activity, and PVP stabilizes such modified NPs. PMID:26215417

  17. Communication: Slow supramolecular mode in amine and thiol derivatives of 2-ethyl-1-hexanol revealed by combined dielectric and shear-mechanical studies.

    PubMed

    Adrjanowicz, K; Jakobsen, B; Hecksher, T; Kaminski, K; Dulski, M; Paluch, M; Niss, K

    2015-11-14

    In this paper, we present results of dielectric and shear-mechanical studies for amine (2-ethyl-1-hexylamine) and thiol (2-ethyl-1-hexanethiol) derivatives of the monohydroxy alcohol, 2-ethyl-1-hexanol. The amine and thiol can form hydrogen bonds weaker in strength than those of the alcohol. The combination of dielectric and shear-mechanical data enables us to reveal the presence of a relaxation mode slower than the α-relaxation. This mode is analogous to the Debye mode seen in monohydroxy alcohols and demonstrates that supramolecular structures are present for systems with lower hydrogen bonding strength. We report some key features accompanying the decrease in the strength of the hydrogen bonding interactions on the relaxation dynamics close to the glass-transition. This includes changes (i) in the amplitude of the Debye and α-relaxations and (ii) the separation between primary and secondary modes.

  18. 40 CFR 721.2805 - Acrylate ester.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Acrylate ester. 721.2805 Section 721... Acrylate ester. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as an acrylate ester (PMN P-96-824) is subject to reporting under...

  19. 40 CFR 721.2805 - Acrylate ester.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Acrylate ester. 721.2805 Section 721... Acrylate ester. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as an acrylate ester (PMN P-96-824) is subject to reporting under...

  20. 40 CFR 721.2805 - Acrylate ester.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Acrylate ester. 721.2805 Section 721... Acrylate ester. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as an acrylate ester (PMN P-96-824) is subject to reporting under...

  1. 40 CFR 721.2805 - Acrylate ester.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Acrylate ester. 721.2805 Section 721... Acrylate ester. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as an acrylate ester (PMN P-96-824) is subject to reporting under...

  2. Mixing It Up with Acrylics.

    ERIC Educational Resources Information Center

    Laird, Shirley

    1999-01-01

    Presents an art activity for fifth-grade students in which they learn about basic shapes and what happens when shapes overlap, draw seven overlapping geometric shapes, review the use of acrylic paint and mixing colors, and finally paint with primary colors. (CMK)

  3. 40 CFR 721.7700 - Poly(oxy-1,2-ethanediyl), α-hydro-ω-(oxiranylmethoxy)-, ether with 2-ethyl-2-(hydroxymethyl)-1,3...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Poly(oxy-1,2-ethanediyl), α-hydro-Ï... Poly(oxy-1,2-ethanediyl), α-hydro-ω-(oxiranylmethoxy)-, ether with 2-ethyl-2-(hydroxymethyl)-1,3... substance identified as poly(oxy-1,2-ethanediyl),α-hydro-ω-(oxiranylmethoxy)-, ether with...

  4. 40 CFR 721.7700 - Poly(oxy-1,2-ethanediyl), α-hydro-ω-(oxiranylmethoxy)-, ether with 2-ethyl-2-(hydroxymethyl)-1,3...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Poly(oxy-1,2-ethanediyl), α-hydro-Ï... Poly(oxy-1,2-ethanediyl), α-hydro-ω-(oxiranylmethoxy)-, ether with 2-ethyl-2-(hydroxymethyl)-1,3... substance identified as poly(oxy-1,2-ethanediyl),α-hydro-ω-(oxiranylmethoxy)-, ether with...

  5. 40 CFR 721.10401 - Oxirane, 2-ethyl-, polymer with oxirane, mono-C11-15-sec-alkyl ethers.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Oxirane, 2-ethyl-, polymer with oxirane, mono-C11-15-sec-alkyl ethers. 721.10401 Section 721.10401 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific...

  6. 40 CFR 721.10400 - Oxirane, 2-ethyl-, polymer with oxirane, mono-C12-14-sec-alkyl ethers.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Oxirane, 2-ethyl-, polymer with oxirane, mono-C12-14-sec-alkyl ethers. 721.10400 Section 721.10400 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific...

  7. 40 CFR 721.10400 - Oxirane, 2-ethyl-, polymer with oxirane, mono-C12-14-sec-alkyl ethers.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... oxirane, mono-C12-14-sec-alkyl ethers. 721.10400 Section 721.10400 Protection of Environment ENVIRONMENTAL..., mono-C12-14-sec-alkyl ethers. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as oxirane, 2-ethyl-, polymer with oxirane,...

  8. 40 CFR 721.10401 - Oxirane, 2-ethyl-, polymer with oxirane, mono-C11-15-sec-alkyl ethers.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... oxirane, mono-C11-15-sec-alkyl ethers. 721.10401 Section 721.10401 Protection of Environment ENVIRONMENTAL..., mono-C11-15-sec-alkyl ethers. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as oxirane, 2-ethyl-, polymer with oxirane, mono...

  9. 40 CFR 721.10401 - Oxirane, 2-ethyl-, polymer with oxirane, mono-C11-15-sec-alkyl ethers.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... oxirane, mono-C11-15-sec-alkyl ethers. 721.10401 Section 721.10401 Protection of Environment ENVIRONMENTAL..., mono-C11-15-sec-alkyl ethers. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as oxirane, 2-ethyl-, polymer with oxirane, mono...

  10. 40 CFR 721.10400 - Oxirane, 2-ethyl-, polymer with oxirane, mono-C12-14-sec-alkyl ethers.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... oxirane, mono-C12-14-sec-alkyl ethers. 721.10400 Section 721.10400 Protection of Environment ENVIRONMENTAL..., mono-C12-14-sec-alkyl ethers. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as oxirane, 2-ethyl-, polymer with oxirane,...

  11. Neurotoxicological and thyroid evaluations of rats developmentally exposed to tris(1,3-dichloro-2-propyl)phosphate (TDICPP) and tris(2-chloro-2-ethyl)phosphate(TCEP)

    EPA Science Inventory

    ABSTRACT: Tris(1,3-dichloro-2-propyl)phosphate (TDICPP) and tris(2-chloro-2-ethyl)phosphate (TCEP) are organophosphorous flame retardants with widespread usage and human exposures through food, inhalation, and dust ingestion. They have been detected in human tissues including ur...

  12. Responses to hexyl 5-aminolevulinate-induced photodynamic treatment in rat bladder cancer model

    NASA Astrophysics Data System (ADS)

    Arum, Carl-Jørgen; Gederas, Odrun; Larsen, Eivind; Randeberg, Lise; Zhao, Chun-Mei

    2010-02-01

    OBJECTIVES: In this study, we evaluated histologically the effects of hexyl 5-aminolevulinateinduced photodynamic treatment in the AY-27 tumor cell induced rat bladder cancer model. MATERIAL & METHODS: The animals (fischer-344 female rats) were divided into 2 groups, half of which were orthotopically implanted with 400,000 syngeniec AY-27 urothelia1 rat bladder cancer cells and half sham implanted. 14 days post implantation 6 rats from each group were treated with hexyl 5-aminolevulinate-induced photodynamic treatment (8mM HAL and light fluence of 20 J/cm2). Additional groups of animals were only given HAL instillation, only light treatment, or no treatment. All animals were sacrificed 7 days after the PDT/only HAL/only light or no treatment. Each bladder was removed, embedded in paraffin and stained with hematoxylin, eosin, and saferin for histological evaluation at high magnification for features of tissue damage by a pathologist blinded to the sample source. RESULTS: In all animals that were AY-27 implanted and not given complete PDT treatment, viable tumors were found in the bladder mucosa and wall. In the animals treated with complete HAL-PDT only 3 of 6 animals had viable tumor. In the 3 animals with viable tumor it was significantly reduced in volume compared to the untreated animals. It was also noted that in the PDT treated animals there was a significantly increased inflammatory response (lymphocytic and mononuclear cell infiltration) in the peri-tumor area compared to implanted animals without complete HAL-PDT. CONCLUSION: Our results suggest that hexyl 5-aminolevulinate-induced photodynamic treatment in a rat bladder cancer model involves both direct effects on cell death (necrosis and apoptosis) and indirect effects to evoke the host immune-response, together contributing to tumor eradication.

  13. Tuning the Surface of Nanoparticles: Impact of Poly(2-ethyl-2-oxazoline) on Protein Adsorption in Serum and Cellular Uptake.

    PubMed

    Koshkina, Olga; Westmeier, Dana; Lang, Thomas; Bantz, Christoph; Hahlbrock, Angelina; Würth, Christian; Resch-Genger, Ute; Braun, Ulrike; Thiermann, Raphael; Weise, Christoph; Eravci, Murat; Mohr, Benjamin; Schlaad, Helmut; Stauber, Roland H; Docter, Dominic; Bertin, Annabelle; Maskos, Michael

    2016-09-01

    Due to the adsorption of biomolecules, the control of the biodistribution of nanoparticles is still one of the major challenges of nanomedicine. Poly(2-ethyl-2-oxazoline) (PEtOx) for surface modification of nanoparticles is applied and both protein adsorption and cellular uptake of PEtOxylated nanoparticles versus nanoparticles coated with poly(ethylene glycol) (PEG) and non-coated positively and negatively charged nanoparticles are compared. Therefore, fluorescent poly(organosiloxane) nanoparticles of 15 nm radius are synthesized, which are used as a scaffold for surface modification in a grafting onto approach. With multi-angle dynamic light scattering, asymmetrical flow field-flow fractionation, gel electrophoresis, and liquid chromatography-mass spectrometry, it is demonstrated that protein adsorption on PEtOxylated nanoparticles is extremely low, similar as on PEGylated nanoparticles. Moreover, quantitative microscopy reveals that PEtOxylation significantly reduces the non-specific cellular uptake, particularly by macrophage-like cells. Collectively, studies demonstrate that PEtOx is a very effective alternative to PEG for stealth modification of the surface of nanoparticles.

  14. Tuning the Surface of Nanoparticles: Impact of Poly(2-ethyl-2-oxazoline) on Protein Adsorption in Serum and Cellular Uptake.

    PubMed

    Koshkina, Olga; Westmeier, Dana; Lang, Thomas; Bantz, Christoph; Hahlbrock, Angelina; Würth, Christian; Resch-Genger, Ute; Braun, Ulrike; Thiermann, Raphael; Weise, Christoph; Eravci, Murat; Mohr, Benjamin; Schlaad, Helmut; Stauber, Roland H; Docter, Dominic; Bertin, Annabelle; Maskos, Michael

    2016-09-01

    Due to the adsorption of biomolecules, the control of the biodistribution of nanoparticles is still one of the major challenges of nanomedicine. Poly(2-ethyl-2-oxazoline) (PEtOx) for surface modification of nanoparticles is applied and both protein adsorption and cellular uptake of PEtOxylated nanoparticles versus nanoparticles coated with poly(ethylene glycol) (PEG) and non-coated positively and negatively charged nanoparticles are compared. Therefore, fluorescent poly(organosiloxane) nanoparticles of 15 nm radius are synthesized, which are used as a scaffold for surface modification in a grafting onto approach. With multi-angle dynamic light scattering, asymmetrical flow field-flow fractionation, gel electrophoresis, and liquid chromatography-mass spectrometry, it is demonstrated that protein adsorption on PEtOxylated nanoparticles is extremely low, similar as on PEGylated nanoparticles. Moreover, quantitative microscopy reveals that PEtOxylation significantly reduces the non-specific cellular uptake, particularly by macrophage-like cells. Collectively, studies demonstrate that PEtOx is a very effective alternative to PEG for stealth modification of the surface of nanoparticles. PMID:27281039

  15. Direct Dynamics Study of Hydrogen-Transfer Isomerization of 1-Pentyl and 1-Hexyl Radicals

    NASA Astrophysics Data System (ADS)

    Zheng, Jingjing; Truhlar, Donald G.

    2009-07-01

    The rate constants of three intramolecular hydrogen-transfer isomerization reactions, namely, 1-4 isomerization of the 1-pentyl radical and 1-4 and 1-5 isomerizations of the 1-hexyl radical, are calculated using variational transition state theory with multidimensional tunneling, in particular by using canonical variational theory (CVT, which is the version of variational transition state theory in which the transition state dividing surface is optimized for a canonical ensemble) with small-curvature tunneling (SCT) for the transmission coefficient. The required potential energy surfaces were obtained implicitly by direct dynamics employing interpolated variational transition state theory with mapping (IVTST-M) and variational transition state theory with interpolated single-point energies (VTST-ISPE). Single-level direct dynamics calculations were performed for all of the reactions by IVTST-M using M06-2X/MG3S or M08-HX/cc-pVTZ+ potential energy surfaces or both. The stationary points of 1-4 isomerization of 1-pentyl and the stationary points for the forward reactions of 1-4 and 1-5 isomerizations of 1-hexyl were also optimized by BMC-CCSD, and for all three reactions we also performed dual-level direct dynamics calculations using VTST-ISPE in which MCG3-MPW single-point energies served as the higher level. The calculated MCG3-MPW//M06-2X/MG3S rate constants agree well with experimental values for 1-4 isomerization of the 1-pentyl radical at high temperature, and this validates the accuracy of this theoretical method for 1-4 isomerization. The MCG3-MPW//M06-2X/MG3S method was therefore used to make a reliable prediction for the rata constants of 1-4 isomerization of the 1-hexyl radical for which a direct experimental measurement is not available. The calculated CVT/SCT/M08-HX/cc-pVTZ+ rate constants agree well with experimental values for 1-5 isomerization of the 1-hexyl radical, and they show that the tunneling effect for these reactions was underestimated in

  16. 2-Cyclo­hexyl­idene-N-methyl­hydrazine­carbothio­amide

    PubMed Central

    Tayamon, Shahedeh; Mazlan, Nurul Ain; Ravoof, Thahira Begum S. A.; Mohamed Tahir, Mohamed Ibrahim; Crouse, Karen A

    2012-01-01

    The title compound C8H15N3S has two mol­ecules in the asymmetric unit in which cis–trans isomerism is exhibited around the N(NH)C=S bonds. The cyclo­hexyl rings in both mol­ecules adopt a chair conformation. In the crystal, N—H⋯S hydrogen bonding produces dimers, which are inter­connected through further N—H⋯S hydrogen bonds, forming chains along the b-axis direction. PMID:23284431

  17. The effects of topically applied hexyl nicotinate lotion on the cutaneous blood flow in patients with Raynaud's phenomenon.

    PubMed

    Bunker, C B; Lanigan, S; Rustin, M H; Dowd, P M

    1988-12-01

    The effect of the epicutaneous application of 0.1% and 1.0% hexyl nicotinate lotion on upper limb skin blood flow was investigated in 25 patients with Raynaud's phenomenon (RP) and five healthy volunteers. Assessments were made using laser Doppler velocimetry. The 0.1% lotion induced an increase in cutaneous blood flow in both controls and patients when applied at different sites on the upper limb. Increased cutaneous blood flow occurred more often when the lotion was applied to the forearm than to the fingers. A greater increase in blood flow and an increased percentage of positive responses was elicited with the 1.0% hexyl nicotinate lotion. Hexyl nicotinate lotion may be of value in the topical treatment of RP.

  18. A method for preparing sodium acrylate-d3, a useful and stable precursor for deuterated acrylic monomers

    SciTech Connect

    Yang, Jun; Hong, Kunlun; Bonnesen, Peter V

    2011-01-01

    A convenient and economical method for converting propiolic acid to sodium acrylate-d3 is described. Successive D/H exchange of the alkyne proton of sodium propiolate (prepared from propiolic acid) using D2O affords sodium propiolate-d having up to 99 atom% D. Sodium propiolate-d can be partially reduced to sodium acrylate-d3 with 90% conversion and 89% yield, using D2 and the Lindlar catalyst with control of reaction parameters to maximize conversion while minimizing over reduction.

  19. 2-(2-Chloro-phen-yl)-N-cyclo-hexyl-2-oxoacetamide.

    PubMed

    Jin, Xiu-Dan; Wu, Jin-Long

    2013-04-01

    In the title compound, C14H16ClNO2, the cyclo-hexyl ring has a chair conformation. The dihedral angle between the benzene ring and the mean plane of the four planar C atoms of the cyclo-hexyl ring is 45.2 (3)°. The two carbonyl groups are trans to one another, with an O=C-C=O torsion angle of -137.1 (3)°. In the crystal, mol-ecules are linked by N-H⋯O hydrogen bonds forming chains propagating along [001]. A region of disordered electron density, situated near the unit-cell corners, was treated using the SQUEEZE routine in PLATON [Spek (2009 ▶). Acta Cryst. D65, 148-155]. It gave a solvent-accessible void of ca 400 Å(3) for only 21 electrons. It is probably due to traces of the solvent of crystallization and was not taken into account during structure refinement. PMID:23634053

  20. Hyperpolarized [1,3-13C2 ]ethyl acetoacetate is a novel diagnostic metabolic marker of liver cancer.

    PubMed

    Jensen, Pernille R; Serra, Sonia Colombo; Miragoli, Luigi; Karlsson, Magnus; Cabella, Claudia; Poggi, Luisa; Venturi, Luca; Tedoldi, Fabio; Lerche, Mathilde H

    2015-02-15

    An increased prevalence of liver diseases such as hepatitis C and nonalcoholic fatty liver results in an augmented incidence of the most common form of liver cancer, hepatocellular carcinoma (HCC). HCC is most often found in the cirrhotic liver and it can therefore be challenging to rely on anatomical information alone when diagnosing HCC. Valuable information on specific cellular metabolism can be obtained with high sensitivity thanks to an emerging magnetic resonance (MR) technique that uses 13C labeled hyperpolarized molecules. Our interest was to explore potential new high contrast metabolic markers of HCC using hyperpolarized 13C-MR. This work led to the identification of a class of substrates, low molecular weight ethyl-esters, which showed high specificity for carboxyl esterases and proved in many cases to possess good properties for signal enhancement. In particular, hyperpolarized [1,3-13C2 ]ethyl acetoacetate (EAA) was shown to provide a metabolic fingerprint of HCC. Using this substrate a liver cancer implanted in rats was diagnosed as a consequence of an ∼4 times higher metabolic substrate-to-product ratio than in the surrounding healthy tissue, (p=0.009). Unregulated cellular uptake as well as cosubstrate independent enzymatic conversion of EAA, made this substrate highly useful as a hyperpolarized 13C-MR marker. This could be appreciated by the signal-to-noise (SNR) obtained from EAA, which was comparable to the SNR reported in a literature liver cancer study with state-of-the-art hyperpolarized substrate, [1-13C]pyruvate. Also, the contrast-to-noise (CNR) in the EAA based metabolic ratio images was significantly improved compared with the CNR in equivalent images reported using [1-13C]pyruvate.

  1. Esterification of acrylic acid with methanol

    SciTech Connect

    Chubarov, G.A.; Danov, S.M.; Logutov, V.I.; Obmelyukhina, T.N.

    1984-01-01

    The esterification of acrylic acid with methanol in the absence of catalysis by strong mineral acids has been studied. The esterification rate was estimated from the amount of methyl acrylate formed at the end of a definite time, and the reaction rate was found to be first order with respect to methanol and second order with respect to acrylic acid. Mathematical relationships in good agreement with experimental data were derived from the results of the kinetic studies.

  2. Experimental and theoretical studies on the coordination chemistry of the N1-hexyl substituted pyrimidines (uracil, 5-fluorouracil and cytosine).

    PubMed

    Barceló-Oliver, Miquel; Baquero, Beatriz Adriana; Bauzá, Antonio; García-Raso, Angel; Vich, Roberto; Mata, Ignasi; Molins, Elies; Terrón, Angel; Frontera, Antonio

    2013-06-01

    N(1)-Hexyl substituted pyrimidines were shown to present solubility properties closer to the real bases than the commonly used methyl and ethyl derivatives, yielding bi-layered structures in the solid state. The study of their coordination capabilities, mainly with Ag(I) and Hg(II), is presented in order to prove their reactivity. A series of coordination complexes, namely, [Hg(N(1)-hexyl-5-fluorouracilate)2]4·6H2O (1), (Ag(+))·[Ag(N(1)-hexyl-5-fluorouracilate)2](-) (2), [Ag(NO3)(N(1)-hexyluracil-κO(4))4] (3), [ZnBr2(N(1)-hexylcytosine)2] (4), [CdBr2(N(1)-hexylcytosine)2] (5), [HgBr2(N(1)-hexylcytosine)2] (6) and [CoBr2(N(1)-hexylcytosine)2] (7), have been synthesized in good yields and X-ray characterized. The presence of the hexyl chains and the fluorine atoms causes the formation of interesting 3D architectures in the solid state. Their structures have been further characterized by infrared spectra (IR) and elemental analyses. In addition, DFT-D3 calculations are used to study interesting noncovalent interactions observed in the solid state, like fluorine-fluorine, fluorine-π and hydrophobic interactions.

  3. 40 CFR 721.304 - Acetic acid, [(5-chloro-8-quinolinyl)oxy-], 1-methyl hexyl ester.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.304 Acetic acid, , 1-methyl hexyl ester. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as acetic acid, -, 1-methylhexyl ester (PMN...

  4. 40 CFR 721.2805 - Acrylate ester.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Acrylate ester. 721.2805 Section 721... Acrylate ester. Link to an amendment published at 79 FR 34637, June 18, 2014. (a) Chemical substance and... ester (PMN P-96-824) is subject to reporting under this section for the significant new uses...

  5. N-Benzoyl-N′,N′′-dicyclo­hexyl­phospho­ric triamide

    PubMed Central

    Pourayoubi, Mehrdad; Rostami Chaijan, Mahnaz; Torre-Fernández, Laura; García-Granda, Santiago

    2011-01-01

    In the title compound, C19H30N3O2P, the central P atom has a distorted tetra­hedral configuration. The N atoms in both cyclo­hexyl­amide moieties exhibit a slight deviation [0.32 (7) and 0.44 (6) Å] from planarity, while the benzoyl­amide N atom is planar [0.11 (3) Å]. In the crystal, mol­ecules are linked via N—H⋯O(P) and N—H⋯O(C) hydrogen bonds, forming R 2 2(10) rings within linear arrangements parallel to the b axis. PMID:21754754

  6. Dicyclo-hexyl-ammonium trimethyl-bis-(hydrogen phenyl-phospho-nato)stannate(IV).

    PubMed

    Diop, Tidiane; Diop, Libasse; Diop, Cheikh A K; Molloy, Kieran C; Kociok-Köhn, Gabriele

    2011-12-01

    In the title compound, (C(12)H(24)N)[Sn(CH(3))(3)(C(6)H(6)O(3)P)(2)], the SnMe(3) residues are axially coordinated by two monodentate [PhPO(3)H](-) anions, leading to a trigonal-bipyramidal geometry for the Sn(IV) atom. The two [SnMe(3)(PhPO(3)H)(2)](-) anions in the unit cell are associated into infinite chains along the a axis by O-H⋯O hydrogen bonds involving the hy-droxy group of the hydrogen phenyl-phospho-nate ion. The chains inter-act with one another via O-H⋯O hydrogen bonds along the c axis. These networks of anions assemble with the dicyclo-hexyl-ammonium ion through N-H⋯O hydrogen bonds, forming a three-dimensional network. PMID:22199636

  7. Crystal structure of 3-benzyl-1-[(cyclo-hexyl-idene)amino]-thio-urea.

    PubMed

    Mohamed, Shaaban K; Mague, Joel T; Akkurt, Mehmet; Hassan, Alaa A; Abdel-Aziz, Ahmed T; Albayati, Mustafa R

    2015-12-01

    The conformation of the title compound, C14H19N3S, is partially determined by an intra-molecular N-H⋯N hydro-gen-bond inter-action, although the N-H⋯N angle of 108° is quite small. The cyclo-hexyl-idene ring has a chair conformation and its mean plane is inclined to the benzene ring by 46.30 (8)°. In the crystal, mol-ecules are linked by pairs of N-H⋯S hydrogen bonds, forming inversion dimers, with an R 2 (2)(8) ring motif. The dimers are reinforced by pairs of C-H⋯S hydrogen bonds, and are linked by further weak C-H⋯S hydrogen bonds, forming chains propagating along [100]. PMID:26870535

  8. Radiopurity measurement of acrylic for DEAP-3600

    SciTech Connect

    Nantais, C. M.; Boulay, M. G.; Cleveland, B. T.

    2013-08-08

    The spherical acrylic vessel that contains the liquid argon target is the most critical detector component in the DEAP-3600 dark matter experiment. Alpha decays near the inner surface of the acrylic vessel are one of the main sources of background in the detector. A fraction of the alpha energy, or the recoiling nucleus from the alpha decay, could misreconstruct in the fiducial volume and result in a false candidate dark matter event. Acrylic has low levels of inherent contamination from {sup 238}U and {sup 232}Th. Another background of particular concern is diffusion of {sup 222}Rn during manufacturing, leading to {sup 210}Pb contamination. The maximum acceptable concentrations in the DEAP-3600 acrylic vessel are ppt levels of {sup 238}U and {sup 232}Th equivalent, and 10{sup −8} ppt {sup 210}Pb. The impurities in the bulk acrylic will be measured by vaporizing a large quantity of acrylic and counting the concentrated residue with ultra-low background HPGe detectors and a low background alpha spectrometer. An overview of the acrylic assay technique is presented.

  9. 21 CFR 177.1310 - Ethylene-acrylic acid copolymers.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Ethylene-acrylic acid copolymers. 177.1310 Section... Use Food Contact Surfaces § 177.1310 Ethylene-acrylic acid copolymers. The ethylene-acrylic acid... for use in contact with food subject to the provisions of this section. (a) The ethylene-acrylic...

  10. 21 CFR 176.110 - Acrylamide-acrylic acid resins.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Acrylamide-acrylic acid resins. 176.110 Section... Paper and Paperboard § 176.110 Acrylamide-acrylic acid resins. Acrylamide-acrylic acid resins may be...) Acrylamide-acrylic acid resins are produced by the polymerization of acrylamide with partial hydrolysis or...

  11. 21 CFR 573.120 - Acrylamide-acrylic acid resin.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 6 2012-04-01 2012-04-01 false Acrylamide-acrylic acid resin. 573.120 Section 573... Food Additive Listing § 573.120 Acrylamide-acrylic acid resin. Acrylamide-acrylic acid resin... acrylamide with partial hydrolysis, or by copolymerization of acrylamide and acrylic acid with the...

  12. 21 CFR 573.120 - Acrylamide-acrylic acid resin.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Acrylamide-acrylic acid resin. 573.120 Section 573... Food Additive Listing § 573.120 Acrylamide-acrylic acid resin. Acrylamide-acrylic acid resin... acrylamide with partial hydrolysis, or by copolymerization of acrylamide and acrylic acid with the...

  13. 21 CFR 573.120 - Acrylamide-acrylic acid resin.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 6 2013-04-01 2013-04-01 false Acrylamide-acrylic acid resin. 573.120 Section 573... Food Additive Listing § 573.120 Acrylamide-acrylic acid resin. Acrylamide-acrylic acid resin... acrylamide with partial hydrolysis, or by copolymerization of acrylamide and acrylic acid with the...

  14. 21 CFR 177.1060 - n-Alkylglutarimide/acrylic copolymers.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 3 2014-04-01 2014-04-01 false n-Alkylglutarimide/acrylic copolymers. 177.1060... Use Food Contact Surfaces § 177.1060 n-Alkylglutarimide/acrylic copolymers. n-Alkylglutarimide/acrylic...) Identity. For the purpose of this section, n-alkylglutarimide/acrylic copolymers are copolymers obtained...

  15. 21 CFR 573.120 - Acrylamide-acrylic acid resin.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 6 2014-04-01 2014-04-01 false Acrylamide-acrylic acid resin. 573.120 Section 573... Food Additive Listing § 573.120 Acrylamide-acrylic acid resin. Acrylamide-acrylic acid resin... acrylamide with partial hydrolysis, or by copolymerization of acrylamide and acrylic acid with the...

  16. 2-Ethyl-3-methylmaleimide in Tokyo Bay sediments providing the first evidence for its formation from chlorophylls in the present photic and oxygenic zone.

    PubMed

    Kozono, Masaki; Nomoto, Shinya; Mita, Hajime; Ishiwatari, Ryoshi; Shimoyama, Akira

    2002-09-01

    Tokyo Bay bottom sediments were analyzed for 2-ethyl-3-methylmaleimide, a degradation product of chlorophylls, which has been detected in ancient sediments. It was found in all sediments examined in concentrations of about 1 to 15 nmol/g- of dried sediment, and it was shown to be preserved for 100 years in the sediments. Its depth distribution agreed with that of the reported total organic carbon content of the sediments, reflecting a change in primary productivity. We concluded that this maleimide was produced under photic and oxygenic conditions in nature before the incorporation of photosynthesizing organisms into sediments.

  17. Volumetric Properties of the Mixture Propenenitrile C3H3N + C4H8O2 Ethyl ethanoate (VMSD1212, LB4262_V)

    NASA Astrophysics Data System (ADS)

    Cibulka, I.; Fontaine, J.-C.; Sosnkowska-Kehiaian, K.; Kehiaian, H. V.

    This document is part of Subvolume C 'Binary Liquid Systems of Nonelectrolytes III' of Volume 26 'Heats of Mixing, Vapor-Liquid Equilibrium, and Volumetric Properties of Mixtures and Solutions' of Landolt-Börnstein Group IV 'Physical Chemistry'. It contains the Chapter 'Volumetric Properties of the Mixture Propenenitrile C3H3N + C4H8O2 Ethyl ethanoate (VMSD1212, LB4262_V)' providing data by calculation of molar excess volume from low-pressure density measurements at variable mole fraction and constant temperature.

  18. Volumetric Properties of the Mixture Propenenitrile C3H3N + C4H8O2 Ethyl ethanoate (VMSD1511, LB4268_V)

    NASA Astrophysics Data System (ADS)

    Cibulka, I.; Fontaine, J.-C.; Sosnkowska-Kehiaian, K.; Kehiaian, H. V.

    This document is part of Subvolume C 'Binary Liquid Systems of Nonelectrolytes III' of Volume 26 'Heats of Mixing, Vapor-Liquid Equilibrium, and Volumetric Properties of Mixtures and Solutions' of Landolt-Börnstein Group IV 'Physical Chemistry'. It contains the Chapter 'Volumetric Properties of the Mixture Propenenitrile C3H3N + C4H8O2 Ethyl ethanoate (VMSD1511, LB4268_V)' providing data from direct measurement of low-pressure thermodynamic speed of sound at variable mole fraction and constant temperature, in the single-phase region(s).

  19. Volumetric Properties of the Mixture Propenenitrile C3H3N + C4H8O2 Ethyl ethanoate (VMSD1111, LB4252_V)

    NASA Astrophysics Data System (ADS)

    Cibulka, I.; Fontaine, J.-C.; Sosnkowska-Kehiaian, K.; Kehiaian, H. V.

    This document is part of Subvolume C 'Binary Liquid Systems of Nonelectrolytes III' of Volume 26 'Heats of Mixing, Vapor-Liquid Equilibrium, and Volumetric Properties of Mixtures and Solutions' of Landolt-Börnstein Group IV 'Physical Chemistry'. It contains the Chapter 'Volumetric Properties of the Mixture Propenenitrile C3H3N + C4H8O2 Ethyl ethanoate (VMSD1111, LB4252_V)' providing data from direct low-pressure measurement of mass density at variable mole fraction and constant temperature, in the single-phase region(s).

  20. Volumetric Properties of the Mixture Propenenitrile C3H3N + C4H8O2 Ethyl ethanoate (VMSD1412, LB4274_V)

    NASA Astrophysics Data System (ADS)

    Cibulka, I.; Fontaine, J.-C.; Sosnkowska-Kehiaian, K.; Kehiaian, H. V.

    This document is part of Subvolume C 'Binary Liquid Systems of Nonelectrolytes III' of Volume 26 'Heats of Mixing, Vapor-Liquid Equilibrium, and Volumetric Properties of Mixtures and Solutions' of Landolt-Börnstein Group IV 'Physical Chemistry'. It contains the Chapter 'Volumetric Properties of the Mixture Propenenitrile C3H3N + C4H8O2 Ethyl ethanoate (VMSD1412, LB4274_V)' providing data by calculation of isentropic compressibility from low-pressure density and thermodynamic speed of sound data at variable mole fraction and constant temperature, in the single-phase region(s).

  1. Carrier transport and luminescence properties of nanocomposites of poly[2-methoxy-5-(2-ethyl hexyloxy)-p-phenylene vinylene] and dehydrated nanotubes titanic acid.

    PubMed

    Zhang, Ting; Xu, Zheng; Liu, Ran; Teng, Feng; Wang, Yongsheng; Xu, Xurong

    2007-12-01

    The carrier transport capability and luminescence efficiency of poly(2-methoxy-5-(2-ethyl hexyloxy)-p-phenylene vinylene) (MEH-PPV) films are enhanced by doping with dehydrated nanotubed titanic acid (DNTA). MEH-PPV molecules, either wrapped on the outer surface of or encapsulated into DNTA pores, have a more open, straighter conformation than undoped molecules, which induces a longer conjugated backbone and stronger interchain interactions, thereby, enhancing carrier mobility. MEH-PPV molecules within DNTA pores have higher exciton recombination efficiency owing to quantum confinement and the antenna effect.

  2. Crystal structure transformation in potassium acrylate

    NASA Astrophysics Data System (ADS)

    Pai Verneker, V. R.; Vasanthakumari, R.

    1983-10-01

    Potassium acrylate undergoes a reversible phase transformation around 335°K with an activation energy of 133 kcal/mole. Differential scanning calorimetry and high temperature X-ray powder diffraction techniques have been used to probe this phenomenon.

  3. Encapsulation of photocells with acrylic prepolymer

    SciTech Connect

    Avenel, M.; Evrard, P.; Leca, J.-P.

    1985-10-22

    Acrylic prepolymer comprising: from 10 to 50% by weight of units derived from at least one alkyl acrylate, the alkyl group having from 4 to 12 carbon atoms, from 30 to 60% by weight of units derived from at least one alkyl methacrylate, the alkyl group having from 1 to 5 carbon atoms, and from 10 to 40% by weight of units derived from methyl acrylate. The prepolymer is used to encapsulate photocells, connected to one another by conducting wires and positioned on a support plate, by casting a resin into the space located between the support plate and a second protective plate, the resin being obtained by mixing 100 parts of the acrylic prepolymer, from 0.1 to 4 parts of a vanadium arenesulphonate and from 0.5 to 4 parts of a free-radical initiator, at a temperature between 10 and 70 C. and for a sufficient time to solidify the polymeric resin at the temperature selected.

  4. FTIR gas-phase kinetic study on the reactions of some acrylate esters with OH radicals and Cl atoms.

    PubMed

    Moreno, A; Gallego-Iniesta, M P; Taccone, R; Martín, M P; Cabañas, B; Salgado, M S

    2014-10-01

    Acrylate esters are α,β-unsaturated esters that contain vinyl groups directly attached to the carbonyl carbon. These compounds are widely used in the production of plastics and resins. Atmospheric degradation processes of these compounds are currently not well understood. The kinetics of the gas phase reactions of OH radicals with methyl 3-methylacrylate and methyl 3,3-dimethylacrylate were determined using the relative rate technique in a 50 L Pyrex photoreactor using in situ FTIR spectroscopy at room temperature (298 ± 2 K) and atmospheric pressure (708 ± 8 Torr) with air as the bath gas. Rate coefficients obtained were (in units cm(3) molecule(-1) s(-1)): (3.27 ± 0.33) × 10(-11) and (4.43 ± 0.42) × 10(-11), for CH3CH═CHC(O)OCH3 and (CH3)2CH═CHC(O)OCH3, respectively. The same technique was used to study the gas phase reactions of hexyl acrylate and ethyl hexyl acrylate with OH radicals and Cl atoms. In the experiments with Cl, N2 and air were used as the bath gases. The following rate coefficients were obtained (in cm(3) molecule(-1) s(-1)): k3 (CH2═CHC(O)O(CH2)5CH3 + Cl) = (3.31 ± 0.31) × 10(-10), k4(CH2═CHC(O)OCH2CH(CH2CH3)(CH2)3CH3 + Cl) = (3.46 ± 0.31) × 10(-10), k5(CH2═CHC(O)O(CH2)5CH3 + OH) = (2.28 ± 0.23) × 10(-11), and k6(CH2═CHC(O)OCH2CH(CH2CH3)(CH2)3CH3 + OH) = (2.74 ± 0.26) × 10(-11). The reactivity increased with the number of methyl substituents on the double bond and with the chain length of the alkyl group in -C(O)OR. Estimations of the atmospheric lifetimes clearly indicate that the dominant atmospheric loss process for these compounds is their daytime reaction with the hydroxyl radical. In coastal areas and in some polluted environments, Cl atom-initiated degradation of these compounds can be significant, if not dominant. Maximum Incremental Reactivity (MIR) index and global warming potential (GWP) were also calculated, and it was concluded that these compounds have significant MIR values, but they do

  5. FTIR gas-phase kinetic study on the reactions of some acrylate esters with OH radicals and Cl atoms.

    PubMed

    Moreno, A; Gallego-Iniesta, M P; Taccone, R; Martín, M P; Cabañas, B; Salgado, M S

    2014-10-01

    Acrylate esters are α,β-unsaturated esters that contain vinyl groups directly attached to the carbonyl carbon. These compounds are widely used in the production of plastics and resins. Atmospheric degradation processes of these compounds are currently not well understood. The kinetics of the gas phase reactions of OH radicals with methyl 3-methylacrylate and methyl 3,3-dimethylacrylate were determined using the relative rate technique in a 50 L Pyrex photoreactor using in situ FTIR spectroscopy at room temperature (298 ± 2 K) and atmospheric pressure (708 ± 8 Torr) with air as the bath gas. Rate coefficients obtained were (in units cm(3) molecule(-1) s(-1)): (3.27 ± 0.33) × 10(-11) and (4.43 ± 0.42) × 10(-11), for CH3CH═CHC(O)OCH3 and (CH3)2CH═CHC(O)OCH3, respectively. The same technique was used to study the gas phase reactions of hexyl acrylate and ethyl hexyl acrylate with OH radicals and Cl atoms. In the experiments with Cl, N2 and air were used as the bath gases. The following rate coefficients were obtained (in cm(3) molecule(-1) s(-1)): k3 (CH2═CHC(O)O(CH2)5CH3 + Cl) = (3.31 ± 0.31) × 10(-10), k4(CH2═CHC(O)OCH2CH(CH2CH3)(CH2)3CH3 + Cl) = (3.46 ± 0.31) × 10(-10), k5(CH2═CHC(O)O(CH2)5CH3 + OH) = (2.28 ± 0.23) × 10(-11), and k6(CH2═CHC(O)OCH2CH(CH2CH3)(CH2)3CH3 + OH) = (2.74 ± 0.26) × 10(-11). The reactivity increased with the number of methyl substituents on the double bond and with the chain length of the alkyl group in -C(O)OR. Estimations of the atmospheric lifetimes clearly indicate that the dominant atmospheric loss process for these compounds is their daytime reaction with the hydroxyl radical. In coastal areas and in some polluted environments, Cl atom-initiated degradation of these compounds can be significant, if not dominant. Maximum Incremental Reactivity (MIR) index and global warming potential (GWP) were also calculated, and it was concluded that these compounds have significant MIR values, but they do

  6. Effects of the ionic liquid 1-hexyl-3-methylimidazolium bromide on root gravitropism in Arabidopsis seedlings.

    PubMed

    Zhang, Liang; Wang, Tianqi; Zheng, Fengxia; Ma, Lingyu; Li, Jingyuan

    2016-03-01

    The toxic effects of ionic liquids (ILs) have attracted increasing attention in recent years. However, the knowledge about the toxic effects of ILs on tropism in organisms remains quite limited. In this study, the effects of 1-hexyl-3-methylimidazolium bromide [C6mim]Br on root gravitropism were evaluated using Arabidopsis seedlings. Our results showed that the root growth and gravity response were significantly inhibited with increasing IL concentration. [C6mim]Br treatment affected the amount and distribution pattern of amyloplasts in root cap compared with controls. The auxin distribution marked with DR5rev::VENUS was altered in IL-treated seedlings. The signal intensity and gene expression of auxin efflux carriers PIN2 and PIN3 were obviously decreased by IL stress. Moreover, as consequences in response to gravity stimulus, the asymmetric DR5 signals in control root apex were impaired by IL treatment. The predominant PIN2 signals along the lower flank of root and PIN3 polarization in columella cells were also significantly reduced in seedlings exposed to IL. Our results suggest that the ionic liquid [C6mim]Br affects the amount and distribution of amyloplasts and disturbs the deployment of PIN2 and PIN3, thus impairing auxin flows in response to gravity stimulus and causing deficient root gravitropism in Arabidopsis seedlings. PMID:26685782

  7. Topical application of ALA and ALA hexyl ester on a subcutaneous murine mammary adenocarcinoma: tissue distribution.

    PubMed

    Perotti, C; Casas, A; Fukuda, H; Sacca, P; Batlle, A

    2003-02-10

    Although 5-aminolevulinic acid (ALA)-based photodynamic therapy (PDT) has proven to be clinically beneficial for the treatment of certain cancers, including a variety of skin cancers, optimal tissue localisation still remains a problem. An approach to improve the bioavailability of protoporphyrin IX (PpIX) is the use of ALA derivatives instead of ALA. In this work, we employed a subcutaneous murine mammary adenocarcinoma to study the tissue distribution pattern of the ALA hexyl ester (He-ALA) in comparison with ALA after their topical application in different vehicles. He-ALA induced porphyrin synthesis in the skin overlying the tumour (SOT), but it did not reach the tumour tissue as efficiently. Only 5 h after He-ALA lotion application, tumour porphyrin levels surpassed control values. He-ALA delivered in cream induced a substantially lower porphyrin synthesis in SOT, reinforcing the importance of the vehicle in the use of topical PDT. Porphyrin levels in internal organs remained almost within control values when He-ALA was employed. The addition of DMSO to ALA formulation slightly increased tumour and SOT porphyrin biosynthesis, but it did not when added to He-ALA lotion.

  8. Dynamical properties of alcohol + 1-hexyl-3-methylimidazolium ionic liquid mixtures: a computer simulation study.

    PubMed

    Méndez-Morales, Trinidad; Carrete, Jesús; García, Manuel; Cabeza, Oscar; Gallego, Luis J; Varela, Luis M

    2011-12-29

    In this work, extensive molecular dynamics simulations of the dynamics of mixtures of ionic liquids (ILs) composed of the cation 1-hexyl-3-methylimidazolium and several anions of different hydrophobicity degrees (Cl(-), BF(4)(-), PF(6)(-)) with alcohols of different chain lengths (methanol and ethanol) are reported. We evaluated the influence of the nature of the anion, the length of the molecular chain of the alcohol, and the alcohol concentration on some dynamical properties of the mixtures, such as self-diffusion coefficients of all the species, mean square displacements (with an analysis of both ballistic and diffusive regimes), and velocity autocorrelation functions of alcohol molecules. The diffusivity of the mixtures was found to be highly dependent on the nature of the anion since the interaction between chloride and alcohols is greater than that with fluorinated anions and leads to slower dynamics. Additionally, our results show that self-diffusion coefficients increase with alcohol concentration. On the other hand, a subdiffusive regime over thousands of picoseconds was detected at intermediate times through analysis of the center-of-mass mean square displacements of alcohol molecules, a region that becomes narrower as alcohol concentration increases. Finally, the study of the role of the anion and of solvent concentration on velocity autocorrelation functions reflects an increase in mean collision times as the amount of alcohol increases until the value of pure alcohols is reached. These collision times are smaller in mixtures with halogenated ILs.

  9. Preparation of mesoporous MnO2/C catalyst for n-hexyl acetate synthesis

    NASA Astrophysics Data System (ADS)

    Yang, Zeheng; Pan, Yanmei; Mei, Zhousheng; Zhang, Weixin

    2012-03-01

    A mesoporous MnO2/C composite was prepared by impregnating self-made porous carbon spheres with manganese nitrate aqueous solution and subsequently reacting with KMnO4 aqueous solution. It was characterized with X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), field emission scanning electron microscopy (FESEM), the Brunauer-Emmett-Teller (BET) surface area and the Barrett-Joyner-Halenda (BJH) pore size distribution. The as-prepared mesoporous MnO2/C composite was used as catalyst for the synthesis of n-hexyl acetate, and the effects of MnO2 loading and esterification reaction parameters on the esterification rate were investigated. The results prove that MnO2 loading has a significant effect on the catalytic activity and that the mesoporous MnO2/C composite exhibits high catalytic activity with an esterification rate of 96.42% under the conditions below: MnO2 loading (73.09 wt%), catalyst dosage (0.1% in total weight), acetic acid/n-hexanol molar ratio (2:1), reaction temperature (130 °C) and reaction time (5 h).

  10. Circadian dosing time dependency in the forearm skin penetration of methyl and hexyl nicotinate.

    PubMed

    Reinberg, A E; Soudant, E; Koulbanis, C; Bazin, R; Nicolaï, A; Mechkouri, M; Touitou, Y

    1995-01-01

    The forearm skin penetration of hydrophilic methyl nicotinate (MN) and lipophilic hexyl nicotinate (HN) was assessed around the clock. The sixteen healthy women (median age: 22 years, weight: 57 kg and height: 162 cm) who volunteered for the study were synchronized with a diurnal activity from 07.00h (+/- 1h) to 23.00h (+/- 1h.30min) and a nocturnal rest before and during the 48h sojourn in air-conditioned rooms (26 degrees C +/- 0.5 degrees C). Both HN (0.5% ethanol solution) and MN (5% ethanol solution) have a vasodilative effect on dermal vessels. The lag time (LT) between the delivery of a fixed volume (10 microliters) of the agent at the skin surface and the beginning of the vasodilatation, detected with a laser-Doppler method, was used to quantify the penetration kinetics. Tests were performed every 4h, at fixed clock hours, over a span of a 40h. Two types of tests were done with each of the agents: fixed site (one site only) and shifted sites (10 different places). Both cosinor and ANOVA have been used for statistical analyses. The shortest LT (fastest penetration) was located around 04.00h. The longest LT (slowest penetration) occurred during the day with a single peak around 13.00h in three of the situations, or two peaks (HN with fixed site). A rather large rhythm amplitude (peak-to-trough difference larger than 50% of the 24h mean LT) was validated.

  11. In vitro study on methemoglobin formation in erythrocytes following hexyl-aminolevulinate induced photodynamic therapy

    NASA Astrophysics Data System (ADS)

    Larsen, Eivind L. P.; Randeberg, Lise L.; Gederaas, Odrun A.; Krokan, Hans E.; Hjelme, Dag R.; Svaasand, Lars O.

    2007-02-01

    Photodynamic therapy (PDT) is a treatment modality which has been shown to be effective for both malignant and non-malignant diseases. New photosensitizers such as hexyl-aminolevulinate (HAL) may increase the efficiency of PDT. HAL penetrates into the cell where the photosensitizer protoporphyrin IX (PPIX) is produced endogenously. In a previous study on HAL based PDT treatment of rat bladder cancer (AY-27 transitional cell carcinoma), a depression of the optical reflectance spectra after treatment was observed in some of the animals. This depression of the spectra was caused by metHemoglobin (metHb). MetHb is an indication of oxidative stress, and can be formed as a result of for instance UV-radiation and heating of blood. The aim of this study was to identify if metHb can be formed in vitro as a result of oxidative stress caused by singlet oxygen and ROS produced during PDT. Methemoglobin formed during PDT might thus be used as an indirect measure of the photochemical processes. This may help predict the PDT treatment outcome. Red blood cells mixed with AY-27 cells exposed to HAL, or PPIX received light treatment, and the changes in the absorption spectra were measured spectrophotometrically. The methemoglobin absorbance spectrum was also studied, and found to be strongly dependant on pH. Hemolysis of erythrocytes by PDT was found, however no metHb was formed in vitro.

  12. [Determination of thermodynamic parameters for ionic liquid 1-hexyl-3-methylimidazolium trifluoromethansulfonate by inverse gas chromatography].

    PubMed

    Deng, Lishuang; Wang, Qiang; Zhang, Zhengfang; Tang, Jun

    2014-02-01

    The thermodynamic parameters of ionic liquid 1-hexyl-3-methylimidazolium trifluoromethansulfonate ([HMIM] OTF) were investigated by inverse gas chromatography in the temperature range of 343.15-373.15 K. Eighteen probe solvents were used to calculate the molar enthalpy of sorption, molar enthalpy of mixing at infinite dilution, molar enthalpy of vaporization and the mass fraction activity coefficients. Furthermore, Flory-Huggins interaction parameters, the solubility parameter of the ionic liquid were calculated to judge the interactions between [HMIM] OTF and the 18 probes solvents. The results showed that among the selected solvents, n-C6-9, tetrahydrofuran, diethyl ether, cyclohexane and benzene are the poor solvents for [HMIM] OTF, while dichloromethane, acetone, chloroform, ethyl acetate, carbon tetrachloride, methyl acetate, toluene and methanol are the favorite solvents for [HMIM] OTF. In addition, the solubility parameter of [HMIM] OTF at room temperature (298.15 K), which was obtained by linear extrapolation method, was 20.74 (J/cm3)0.5. This study could be used as a reference to the application and research of the ionic liquids. PMID:24822452

  13. Amphiphilic poly(D- or L-lactide)-b-poly(N,N-dimethylamino-2-ethyl methacrylate) block copolymers: controlled synthesis, characterization, and stereocomplex formation.

    PubMed

    Spasova, Mariya; Mespouille, Laetitia; Coulembier, Olivier; Paneva, Dilyana; Manolova, Nevena; Rashkov, Iliya; Dubois, Philippe

    2009-05-11

    Novel well-defined amphiphilic poly(D-lactide)-b-poly(N,N-dimethylamino-2-ethyl methacrylate) (PDLA-b-PDMAEMA) and poly(L-lactide)-b-poly(N,N-dimethylamino-2-ethyl methacrylate) (PLLA-b-PDMAEMA) copolymers were obtained. The synthesis strategy consisted of a three-step procedure: (i) controlled ring-opening polymerization (ROP) of (D- or L-)lactide initiated by Al(O(i)Pr)(3), followed by (ii) quantitative conversion of the polylactide (PLA) hydroxyl end-groups with bromoisobutyryl bromide and (iii) atom transfer radical polymerization (ATRP) of DMAEMA. The PLA block molecular weight was kept below 5000 g/mol. The macromolecular parameters of the (co)polymers were determined by (1)H NMR spectroscopy and size exclusion chromatography (SEC). The stereocomplexes of PDLA-b-PDMAEMA/PLLA-b-PDMAEMA diblock copolymers were prepared via solvent casting. The stereocomplex formation was evidenced by differential scanning calorimetry (DSC) and X-ray diffraction (XRD) analyses. The obtained stereocomplexes had melting temperature of about 65 degrees C above that of the individual copolymers and exhibited diffraction patterns assigned to the stereocomplex crystallites. In addition, for the first time it was shown that the replacement of one of the PLA partners with high molecular weight PLLA or PDLA did not hamper the stereocomplex formation. The presence of PDMAEMA blocks proved to impart hydrophilicity of the synthesized copolymers and related stereocomplexes, as determined by static water contact angle measurements. PMID:19331403

  14. Allergic contact dermatitis to acrylates in disposable blue diathermy pads.

    PubMed Central

    Sidhu, S. K.; Shaw, S.

    1999-01-01

    We report 2 cases of elicitation of allergic contact dermatitis to acrylates from disposable blue diathermy pads used on patients who underwent routine surgery. Their reactions were severe, and took approximately 5 weeks to resolve. Both patients gave a prior history of finger tip dermatitis following the use of artificial sculptured acrylic nails, which is a common, but poorly reported, cause of acrylate allergy. Patch testing subsequently confirmed allergies to multiple acrylates present in both the conducting gel of disposable blue diathermy pads, and artificial sculptured acrylic nails. We advocate careful history taking prior to surgery to avoid unnecessary exposure to acrylates in patients already sensitized. Images Figure 1 Figure 2 PMID:10364952

  15. 21 CFR 173.5 - Acrylate-acrylamide resins.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... additive consists of one of the following: (1) Acrylamide-acrylic acid resin (hydrolyzed polyacrylamide) is... and acrylic acid, with the greater part of the polymer being composed of acrylamide units. (2)...

  16. Connection between the conformation and emission properties of poly[2-methoxy-5-(2'-ethyl-hexyloxy)-1,4-phenylene vinylene] single molecules during thermal annealing

    NASA Astrophysics Data System (ADS)

    Ou, Jiemei; Yang, Yuzhao; Lin, Wensheng; Yuan, Zhongke; Gan, Lin; Lin, Xiaofeng; Chen, Xudong; Chen, Yujie

    2015-03-01

    We investigated the transitions of conformations and their effects on emission properties of poly[2-methoxy-5-(2'-ethyl-hexyloxy)-1,4-phenylene vinylene] (MEH-PPV) single molecules in PMMA matrix during thermal annealing process. Total internal reflection fluorescence microscopy measurements reveal the transformation from collapsed conformations to extended, highly ordered rod-like structures of MEH-PPV single molecules during thermal annealing. The blue shifts in the ensemble single molecule PL spectra support our hypnosis. The transition occurs as the annealing temperature exceeds 100 °C, implying that an annealing temperature near the glass transition temperature Tg of matrix is ideal for the control and optimization of blend polymer films.

  17. Drying temperature effects on electrical and optical properties of poly[2-methoxy-5-(2'-ethyl-hexyloxy)-1,4-phenylene vinylene] (MEH-PPV) thin film

    NASA Astrophysics Data System (ADS)

    Azhar, N. E. A.; Affendi, I. H. H.; Shafura, A. K.; Shariffudin, S. S.; Alrokayan, Salman A. H.; Khan, Haseeb A.; Rusop, M.

    2016-07-01

    Temperature effects on electrical and optical properties of a representative semiconducting polymer, poly[2-methoxy-5-(2'-ethyl-hexyloxy)-1,4-phenylene vinylene] (MEH-PPV), has recently attracted much attention. The MEH-PPV thin films were deposited at different drying temperature (anneal temperature) using spin-coating technique. The spin coating technique was used to produce uniform film onto large area. The MEH-PPV was dissolved in toluene solution to exhibits different optical and electrical properties. The absorption coefficient and bandgap was measured using UV-Visible-NIR (UV-VIS-NIR). The bandgap of MEH-PPV was effect by the thickness of thin films. For electrical properties, two-point probe was used to characterize the current-voltage measurement. The current-voltage measurement shows that the MEH-PPV thin films become more conductive at high temperature. This study will provide better performance and suitable for optoelectronic device especially OLEDs applications.

  18. 40 CFR 721.324 - Alkoxylated acrylate polymer (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Alkoxylated acrylate polymer (generic... Substances § 721.324 Alkoxylated acrylate polymer (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as alkoxylated acrylate...

  19. 40 CFR 721.324 - Alkoxylated acrylate polymer (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Alkoxylated acrylate polymer (generic... Substances § 721.324 Alkoxylated acrylate polymer (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as alkoxylated acrylate...

  20. 40 CFR 721.324 - Alkoxylated acrylate polymer (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Alkoxylated acrylate polymer (generic... Substances § 721.324 Alkoxylated acrylate polymer (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as alkoxylated acrylate...

  1. 40 CFR 721.5325 - Nickel acrylate complex.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Nickel acrylate complex. 721.5325... Substances § 721.5325 Nickel acrylate complex. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance nickel acrylate complex (PMN P-85-1034) is subject to reporting...

  2. 40 CFR 721.5325 - Nickel acrylate complex.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Nickel acrylate complex. 721.5325... Substances § 721.5325 Nickel acrylate complex. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance nickel acrylate complex (PMN P-85-1034) is subject to reporting...

  3. 40 CFR 721.5325 - Nickel acrylate complex.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Nickel acrylate complex. 721.5325... Substances § 721.5325 Nickel acrylate complex. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance nickel acrylate complex (PMN P-85-1034) is subject to reporting...

  4. 40 CFR 721.5325 - Nickel acrylate complex.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Nickel acrylate complex. 721.5325... Substances § 721.5325 Nickel acrylate complex. Link to an amendment published at 79 FR 34637, June 18, 2014... nickel acrylate complex (PMN P-85-1034) is subject to reporting under this section for the...

  5. 40 CFR 721.5325 - Nickel acrylate complex.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Nickel acrylate complex. 721.5325... Substances § 721.5325 Nickel acrylate complex. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance nickel acrylate complex (PMN P-85-1034) is subject to reporting...

  6. 21 CFR 573.120 - Acrylamide-acrylic acid resin.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Acrylamide-acrylic acid resin. 573.120 Section 573.120 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... Food Additive Listing § 573.120 Acrylamide-acrylic acid resin. Acrylamide-acrylic acid...

  7. 21 CFR 173.5 - Acrylate-acrylamide resins.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Acrylate-acrylamide resins. 173.5 Section 173.5... CONSUMPTION Polymer Substances and Polymer Adjuvants for Food Treatment § 173.5 Acrylate-acrylamide resins. Acrylate-acrylamide resins may be safely used in food under the following prescribed conditions: (a)...

  8. 21 CFR 176.110 - Acrylamide-acrylic acid resins.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Acrylamide-acrylic acid resins. 176.110 Section 176... Substances for Use Only as Components of Paper and Paperboard § 176.110 Acrylamide-acrylic acid resins. Acrylamide-acrylic acid resins may be safely used as components of articles intended for use in...

  9. 21 CFR 176.110 - Acrylamide-acrylic acid resins.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Acrylamide-acrylic acid resins. 176.110 Section... Substances for Use Only as Components of Paper and Paperboard § 176.110 Acrylamide-acrylic acid resins. Acrylamide-acrylic acid resins may be safely used as components of articles intended for use in...

  10. 21 CFR 177.1310 - Ethylene-acrylic acid copolymers.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Ethylene-acrylic acid copolymers. 177.1310 Section... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1310 Ethylene-acrylic acid copolymers. The ethylene-acrylic acid copolymers identified in paragraph (a) of this section may be...

  11. 21 CFR 177.1310 - Ethylene-acrylic acid copolymers.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ethylene-acrylic acid copolymers. 177.1310 Section... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1310 Ethylene-acrylic acid copolymers. The ethylene-acrylic acid copolymers identified in paragraph (a) of this section may be...

  12. 21 CFR 176.110 - Acrylamide-acrylic acid resins.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Acrylamide-acrylic acid resins. 176.110 Section... Substances for Use Only as Components of Paper and Paperboard § 176.110 Acrylamide-acrylic acid resins. Acrylamide-acrylic acid resins may be safely used as components of articles intended for use in...

  13. 21 CFR 177.1310 - Ethylene-acrylic acid copolymers.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Ethylene-acrylic acid copolymers. 177.1310 Section... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1310 Ethylene-acrylic acid copolymers. The ethylene-acrylic acid copolymers identified in paragraph (a) of this section may be...

  14. 40 CFR 721.10537 - Acrylate ester (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Acrylate ester (generic). 721.10537... Substances § 721.10537 Acrylate ester (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as acrylate ester (PMN P-01-579) is subject...

  15. 40 CFR 721.10477 - Acrylate ester (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Acrylate ester (generic). 721.10477... Substances § 721.10477 Acrylate ester (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as acrylate ester (PMN P-04-290) is subject...

  16. 40 CFR 721.10477 - Acrylate ester (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Acrylate ester (generic). 721.10477... Substances § 721.10477 Acrylate ester (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as acrylate ester (PMN P-04-290) is subject...

  17. 40 CFR 721.10537 - Acrylate ester (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Acrylate ester (generic). 721.10537... Substances § 721.10537 Acrylate ester (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as acrylate ester (PMN P-01-579) is subject...

  18. 21 CFR 177.1320 - Ethylene-ethyl acrylate copolymers.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... prescribed for polyethylene in § 177.1520. (1) Specifications—(i) Infrared identification. Ethylene-ethyl acrylate copolymers can be identified by their characteristic infrared spectra. (ii) Quantitative determination of ethyl acrylate content. The ethyl acrylate can be determined by the infrared spectra. Prepare...

  19. 21 CFR 177.1320 - Ethylene-ethyl acrylate copolymers.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... prescribed for polyethylene in § 177.1520. (1) Specifications—(i) Infrared identification. Ethylene-ethyl acrylate copolymers can be identified by their characteristic infrared spectra. (ii) Quantitative determination of ethyl acrylate content. The ethyl acrylate can be determined by the infrared spectra. Prepare...

  20. 40 CFR 721.324 - Alkoxylated acrylate polymer (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Alkoxylated acrylate polymer (generic... Substances § 721.324 Alkoxylated acrylate polymer (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as alkoxylated acrylate...

  1. 40 CFR 721.324 - Alkoxylated acrylate polymer (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Alkoxylated acrylate polymer (generic... Substances § 721.324 Alkoxylated acrylate polymer (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as alkoxylated acrylate...

  2. 40 CFR 721.484 - Fluorinated acrylic copolymer (generic name).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Fluorinated acrylic copolymer (generic... Specific Chemical Substances § 721.484 Fluorinated acrylic copolymer (generic name). (a) Chemical substance... fluorinated acrylic copolymer (PMN P-95-1208) is subject to reporting under this section for the...

  3. 40 CFR 721.484 - Fluorinated acrylic copolymer (generic name).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Fluorinated acrylic copolymer (generic... Specific Chemical Substances § 721.484 Fluorinated acrylic copolymer (generic name). (a) Chemical substance... fluorinated acrylic copolymer (PMN P-95-1208) is subject to reporting under this section for the...

  4. 40 CFR 721.10180 - Trifunctional acrylic ester (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Trifunctional acrylic ester (generic... Specific Chemical Substances § 721.10180 Trifunctional acrylic ester (generic). (a) Chemical substance and... acrylic ester (PMN P-04-692) is subject to reporting under this section for the significant new...

  5. 40 CFR 721.10180 - Trifunctional acrylic ester (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Trifunctional acrylic ester (generic... Specific Chemical Substances § 721.10180 Trifunctional acrylic ester (generic). (a) Chemical substance and... acrylic ester (PMN P-04-692) is subject to reporting under this section for the significant new...

  6. 21 CFR 177.1060 - n-Alkylglutarimide/acrylic copolymers.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 3 2012-04-01 2012-04-01 false n-Alkylglutarimide/acrylic copolymers. 177.1060... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1060 n-Alkylglutarimide/acrylic copolymers. n-Alkylglutarimide/acrylic copolymers identified in this section may be safely used as...

  7. 40 CFR 721.10180 - Trifunctional acrylic ester (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Trifunctional acrylic ester (generic... Specific Chemical Substances § 721.10180 Trifunctional acrylic ester (generic). (a) Chemical substance and... acrylic ester (PMN P-04-692) is subject to reporting under this section for the significant new...

  8. 40 CFR 721.484 - Fluorinated acrylic copolymer (generic name).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Fluorinated acrylic copolymer (generic... Specific Chemical Substances § 721.484 Fluorinated acrylic copolymer (generic name). (a) Chemical substance... fluorinated acrylic copolymer (PMN P-95-1208) is subject to reporting under this section for the...

  9. 40 CFR 721.484 - Fluorinated acrylic copolymer (generic name).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Fluorinated acrylic copolymer (generic... Specific Chemical Substances § 721.484 Fluorinated acrylic copolymer (generic name). (a) Chemical substance... fluorinated acrylic copolymer (PMN P-95-1208) is subject to reporting under this section for the...

  10. 21 CFR 177.1060 - n-Alkylglutarimide/acrylic copolymers.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true n-Alkylglutarimide/acrylic copolymers. 177.1060... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1060 n-Alkylglutarimide/acrylic copolymers. n-Alkylglutarimide/acrylic copolymers identified in this section may be safely used as...

  11. 21 CFR 177.1060 - n-Alkylglutarimide/acrylic copolymers.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 3 2011-04-01 2011-04-01 false n-Alkylglutarimide/acrylic copolymers. 177.1060... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1060 n-Alkylglutarimide/acrylic copolymers. n-Alkylglutarimide/acrylic copolymers identified in this section may be safely used as...

  12. 40 CFR 721.10180 - Trifunctional acrylic ester (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Trifunctional acrylic ester (generic... Specific Chemical Substances § 721.10180 Trifunctional acrylic ester (generic). (a) Chemical substance and... acrylic ester (PMN P-04-692) is subject to reporting under this section for the significant new...

  13. 21 CFR 177.1310 - Ethylene-acrylic acid copolymers.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Ethylene-acrylic acid copolymers. 177.1310 Section... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1310 Ethylene-acrylic acid copolymers. The ethylene-acrylic acid copolymers identified in paragraph (a) of this section may be...

  14. 21 CFR 176.110 - Acrylamide-acrylic acid resins.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Acrylamide-acrylic acid resins. 176.110 Section... Substances for Use Only as Components of Paper and Paperboard § 176.110 Acrylamide-acrylic acid resins. Acrylamide-acrylic acid resins may be safely used as components of articles intended for use in...

  15. 40 CFR 721.484 - Fluorinated acrylic copolymer (generic name).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Fluorinated acrylic copolymer (generic... Specific Chemical Substances § 721.484 Fluorinated acrylic copolymer (generic name). (a) Chemical substance... fluorinated acrylic copolymer (PMN P-95-1208) is subject to reporting under this section for the...

  16. 40 CFR 721.10180 - Trifunctional acrylic ester (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Trifunctional acrylic ester (generic... Specific Chemical Substances § 721.10180 Trifunctional acrylic ester (generic). (a) Chemical substance and... acrylic ester (PMN P-04-692) is subject to reporting under this section for the significant new...

  17. 21 CFR 177.1060 - n-Alkylglutarimide/acrylic copolymers.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 3 2013-04-01 2013-04-01 false n-Alkylglutarimide/acrylic copolymers. 177.1060... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1060 n-Alkylglutarimide/acrylic copolymers. n-Alkylglutarimide/acrylic copolymers identified in this section may be safely used as...

  18. 40 CFR 721.10307 - Acrylate resin (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Acrylate resin (generic). 721.10307... Substances § 721.10307 Acrylate resin (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as acrylate resin (PMN P-01-343) is subject...

  19. 40 CFR 721.10307 - Acrylate resin (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Acrylate resin (generic). 721.10307... Substances § 721.10307 Acrylate resin (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as acrylate resin (PMN P-01-343) is subject...

  20. 21 CFR 173.5 - Acrylate-acrylamide resins.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Acrylate-acrylamide resins. 173.5 Section 173.5... CONSUMPTION Polymer Substances and Polymer Adjuvants for Food Treatment § 173.5 Acrylate-acrylamide resins. Acrylate-acrylamide resins may be safely used in food under the following prescribed conditions: (a)...

  1. Acrylic Tanks for Stunning Chemical Demonstrations

    ERIC Educational Resources Information Center

    Mirholm, Alexander; Ellervik, Ulf

    2009-01-01

    We describe the use of acrylic tanks (400 x 450 x 27 mm) for visualization of chemical demonstrations in aqueous solutions. Examples of well-suited demonstrations are oscillating reactions, pH indicators, photochemical reduction of Lauth's violet, and chemoluminiscent reactions. (Contains 1 figure.)

  2. 40 CFR 721.405 - Polyether acrylate.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 721.405 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.405 Polyether acrylate. (a) Chemical substance and significant new uses subject to reporting....

  3. 40 CFR 721.405 - Polyether acrylate.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 721.405 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.405 Polyether acrylate. (a) Chemical substance and significant new uses subject to reporting....

  4. UV-curable acrylated coating from epoxidized palm oil

    NASA Astrophysics Data System (ADS)

    Rahman, Nurliyana Abd; Badri, Khairiah Haji; Salleh, Nik Ghazali Nik

    2014-09-01

    The properties of coating film prepared from the incorporation of acrylated palm oil (EPOLA) in commercial epoxy acrylate have been studied. A series of different amount of EPOLA was mixed with commercial epoxy acrylate. The blended acrylates passed through UV light to produce a non-tacky film. The conversion of acrylate double bond was monitored by FTIR. The effect of EPOLA concentration onto coated films were investigated by determination of the pendulum hardness and gel content. The higher the amount of EPOLA, the lower the pendulum hardness and the gel content but to a level acceptable for usage in the high-end applications.

  5. Synthesis and Characteristics of Fullerene Derivatives with Hexyl Perylene Moieties as N-Type Materials in Organic Solar Cells.

    PubMed

    Han, Seong Hun; Kim, Gyu Min; Oh, Se Young

    2015-07-01

    Recently, fullerene derivatives have received significant attention due to their potential impacts on the development of high performance organic photovoltaic (OPV) cells. One of the most successful fullerene derivatives thus far is [6, 6]-phenyl-C61-butyric acid methyl ester (PCBM), which is being used as an electron acceptor material. However, PCBM has some disadvantages concerning its application in OPV cells, such as a weak absorption rate in the visible region and a relatively low LUMO level. In the present work, we synthesized a novel fullerene derivative, called hexyl perylene fullerene (HPF), which contains a hexyl perylene moiety. The HPF molecules showed two absorption peaks at 340 nm and 450 nm corresponding to the fullerene and to the perylene moiety, respectively. 1,8-octanedithiol was used as an additive to improve the compatibility between the poly(3-hexylthiophene) (P3HT) and the synthesized HPF The characteristics of an OPV cell composed of ITO/PEDOT:PSS/P3HT:HPF:1,8-octanedithiol/Al were investigated.

  6. Large Acrylic Spherical Windows In Hyperbaric Underwater Photography

    NASA Astrophysics Data System (ADS)

    Lones, Joe J.; Stachiw, Jerry D.

    1983-10-01

    Both acrylic plastic and glass are common materials for hyperbaric optical windows. Although glass continues to be used occasionally for small windows, virtually all large viewports are made of acrylic. It is easy to uderstand the wide use of acrylic when comparing design properties of this plastic with those of glass, and glass windows are relatively more difficult to fabricate and use. in addition there are published guides for the design and fabrication of acrylic windows to be used in the hyperbaric environment of hydrospace. Although these procedures for fabricating the acrylic windows are somewhat involved, the results are extremely reliable. Acrylic viewports are now fabricated to very large sizes for manned observation or optical quality instrumen tation as illustrated by the numerous acrylic submersible vehicle hulls for hu, an occupancy currently in operation and a 3600 large optical window recently developed for the Walt Disney Circle Vision under-water camera housing.

  7. Thickness dependent absorption and polaron photogeneration in poly-(2-metoxy-5-(2'-ethyl-hexyloxy)-1,4-phenylene-vinylene)

    NASA Astrophysics Data System (ADS)

    Petrović, J. P.; Matavulj, P. S.; Pinto, L. R.; Thapa, A.; Živanović, S. R.

    2012-06-01

    A comprehensive photocurrent spectra analysis of the ITO/PEDOT:PSS/MEH-PPV/Al devices with three different poly-(2-metoxy-5-(2'-ethyl-hexyloxy)-1,4-phenylene-vinylene) or MEH-PPV thin-film thicknesses is used to investigate charge carrier photogeneration in this polymer. The photocurrent is calculated based on the hole polaron drift-diffusion model including Poole-Frenkel (P-F) transport. Two mechanisms (monomolecular and Langevin-type bimolecular) for hole polaron recombination are considered separately. The MEH-PPV absorption coefficient spectra dependence on the thin film thickness is experimentally determined and included in our model. By comparing the simulated photocurrent spectra to measured data in the wide range of bias voltages and for devices with different MEH-PPV film thicknesses the polaron photogeneration quantum efficiency (θp) as a function of the electric field is extracted. The θp curves obtained for different devices are perfectly fitted by the P-F expression. It is shown that polaron photogeneration process in the thin MEH-PPV films is affected by the film thickness. A unique polaron photogeneration model which accounts for the field and thickness dependences is achieved when one of the P-F parameters is left to be thickness dependent.

  8. Highly selective polymer electrolyte membranes consisting of poly(2-ethyl-2-oxazoline) and Cu(NO3)2 for SF6 separation

    PubMed Central

    Lee, Woong Gi; Kang, Sang Wook

    2016-01-01

    Polymer electrolyte membranes consisting of Cu(NO3)2 and poly(2-ethyl-2-oxazoline) (POZ) were prepared for SF6/N2 separation. It was anticipated that repulsive forces would be operative between the negative charge of water and the F atoms of SF6 when Cu(NO3)2 in the composite was solvated by water, and that the barrier effect of Cu2+ ions would be activated. In fact, Cu(NO3)2 solvated by water in the POZ membrane was observed to have more higher-order ionic aggregates than free ions or ion pairs, as confirmed by FT-Raman spectroscopy. Thus, when Cu(NO3)2 solvated by water was incorporated into the POZ matrix, the N2/SF6 selectivity increased to 28.0 with a N2 permeance of 11.2 GPU at a POZ/Cu(NO3)2 mole ratio of 1:0.7. The coordinative interaction of Cu(NO3)2 with the carbonyl group in POZ was confirmed by FT-IR spectroscopy and TGA, and the film thickness of the membrane was determined from SEM analysis. PMID:26861503

  9. Highly selective polymer electrolyte membranes consisting of poly(2-ethyl-2-oxazoline) and Cu(NO3)2 for SF6 separation

    NASA Astrophysics Data System (ADS)

    Lee, Woong Gi; Kang, Sang Wook

    2016-02-01

    Polymer electrolyte membranes consisting of Cu(NO3)2 and poly(2-ethyl-2-oxazoline) (POZ) were prepared for SF6/N2 separation. It was anticipated that repulsive forces would be operative between the negative charge of water and the F atoms of SF6 when Cu(NO3)2 in the composite was solvated by water, and that the barrier effect of Cu2+ ions would be activated. In fact, Cu(NO3)2 solvated by water in the POZ membrane was observed to have more higher-order ionic aggregates than free ions or ion pairs, as confirmed by FT-Raman spectroscopy. Thus, when Cu(NO3)2 solvated by water was incorporated into the POZ matrix, the N2/SF6 selectivity increased to 28.0 with a N2 permeance of 11.2 GPU at a POZ/Cu(NO3)2 mole ratio of 1:0.7. The coordinative interaction of Cu(NO3)2 with the carbonyl group in POZ was confirmed by FT-IR spectroscopy and TGA, and the film thickness of the membrane was determined from SEM analysis.

  10. Inverted polymer fullerene solar cells exceeding 10% efficiency with poly(2-ethyl-2-oxazoline) nanodots on electron-collecting buffer layers

    PubMed Central

    Nam, Sungho; Seo, Jooyeok; Woo, Sungho; Kim, Wook Hyun; Kim, Hwajeong; Bradley, Donal D. C.; Kim, Youngkyoo

    2015-01-01

    Polymer solar cells have been spotlighted due to their potential for low-cost manufacturing but their efficiency is still less than required for commercial application as lightweight/flexible modules. Forming a dipole layer at the electron-collecting interface has been suggested as one of the more attractive approaches for efficiency enhancement. However, only a few dipole layer material types have been reported so far, including only one non-ionic (charge neutral) polymer. Here we show that a further neutral polymer, namely poly(2-ethyl-2-oxazoline) (PEOz) can be successfully used as a dipole layer. Inclusion of a PEOz layer, in particular with a nanodot morphology, increases the effective work function at the electron-collecting interface within inverted solar cells and thermal annealing of PEOz layer leads to a state-of-the-art 10.74% efficiency for single-stack bulk heterojunction blend structures comprising poly[4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b:4,5-b′]dithiophene-alt-3-fluorothieno[3,4-b]thiophene-2-carboxylate] as donor and [6,6]-phenyl-C71-butyric acid methyl ester as acceptor. PMID:26656447

  11. Repeated exposure toxicity of 2-ethyl-1,3-hexanediol by cutaneous applications to the rat for 9 and 90 days.

    PubMed

    Van Miller, J P; Losco, P E; Neptun, D A; Ballantyne, B

    1995-02-01

    2-Ethyl-1,3-hexanediol (EHD; CASRN 94-96-2), an industrial chemical and insect repellent, has a high potential for recurrent skin contact. Short-term (9 d) and subchronic (13 w) repeated epicutaneous contact studies were conducted to determine the potential for cumulative local skin irritation and systemic toxicity in Fischer 344 rats. Doses were 0.5, 2.0 or 4.0 ml/kg/d of undiluted EHD. There were no clinical signs and no treatment-related effects on hematology, clinical chemistry or histology of a large number of organs and tissues including the treated skin. The only effects where slight decreases in body weight gain for the high-dose males in the 9-d study and males and females of the high-dose group in the subchronic study; slight decreases in food consumption for females of all treatment groups in the subchronic study; and slight increases in relative liver weight for high-dose females in the 9-d study and high-dose males in the subchronic study, which is probably a compensatory hypertrophy for the metabolism of EHD. Thus, recurrent epicutaneous applications of undiluted EHD to the rat did not cause any local skin irritation or cumulative or organ-specific toxicity. PMID:7709587

  12. Inverted polymer fullerene solar cells exceeding 10% efficiency with poly(2-ethyl-2-oxazoline) nanodots on electron-collecting buffer layers

    NASA Astrophysics Data System (ADS)

    Nam, Sungho; Seo, Jooyeok; Woo, Sungho; Kim, Wook Hyun; Kim, Hwajeong; Bradley, Donal D. C.; Kim, Youngkyoo

    2015-12-01

    Polymer solar cells have been spotlighted due to their potential for low-cost manufacturing but their efficiency is still less than required for commercial application as lightweight/flexible modules. Forming a dipole layer at the electron-collecting interface has been suggested as one of the more attractive approaches for efficiency enhancement. However, only a few dipole layer material types have been reported so far, including only one non-ionic (charge neutral) polymer. Here we show that a further neutral polymer, namely poly(2-ethyl-2-oxazoline) (PEOz) can be successfully used as a dipole layer. Inclusion of a PEOz layer, in particular with a nanodot morphology, increases the effective work function at the electron-collecting interface within inverted solar cells and thermal annealing of PEOz layer leads to a state-of-the-art 10.74% efficiency for single-stack bulk heterojunction blend structures comprising poly[4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b:4,5-b']dithiophene-alt-3-fluorothieno[3,4-b]thiophene-2-carboxylate] as donor and [6,6]-phenyl-C71-butyric acid methyl ester as acceptor.

  13. Intercalation of acrylic acid and sodium acrylate into kaolinite and their in situ polymerization

    NASA Astrophysics Data System (ADS)

    Zhang, Bo; Li, Yanfeng; Pan, Xiaobing; Jia, Xin; Wang, Xiaolong

    2007-02-01

    Novel nano-composites of poly (acrylic acid)-kaolinite were prepared, and intercalation and in situ polymerization were used in this process. The nano-composites were obtained by in situ polymerization of acrylic acid (AA) and sodium acrylate (AANa) intercalated into organo-kaolinite, which was obtained by refining and chemically modifying with solution intercalation step in order to increase the basal plane distance of the original clay. The modification was completed by using dimethyl-sulfoxide (DMSO)/methanol and potassium acetate (KAc)/water systems step by step. The materials were characterized with the help of XRD, FT-IR and TEM; the results confirmed that poly(acrylic acid) (PAA) and poly(sodium acrylate) (PAANa) were intercalated into the interlamellar spaces of kaolinite, the resulting copolymer composites (CC0 : copolymer crude kaolinite composite, CC1 : copolymer DMSO kaolinite composite, CC2 : copolymer KAc kaolinite composite) of CC2 exhibited a lamellar nano-composite with a mixed nano-morphology, and partial exfoliation of the intercalating clay platelets should be the main morphology. Finally, the effect of neutralization degree on the intercalation behavior was also investigated.

  14. 'Weightless' acrylic painting by Jack Kroehnke

    NASA Technical Reports Server (NTRS)

    1987-01-01

    'Weightless' acrylic painting by Jack Kroehnke depicts STS-26 Discovery, Orbiter Vehicle (OV) 103, Mission Specialist (MS) David C. Hilmers participating in extravehicular activity (EVA) simulation in JSC Weightless Environment Training Facility (WETF) Bldg 29. In the payload bay (PLB) mockup, Hilmers, wearing extravehicular mobility unit (EMU), holds onto the mission-peculiar equipment support structure in foreground while SCUBA-equipped diver monitors activity overhead and camera operator records EVA procedures. Copyrighted art work for use by NASA.

  15. ICI/BASF PP for acrylics swap

    SciTech Connect

    Alperowicz, N.

    1993-01-27

    ICI (London) and BASF (Ludwigshafen) have announced their long-awaited polypropylene (PP) for acrylics swap deal. ICI is buying BASF's European acrylic resin business, and the German firm will acquire ICI's European PP operations. The deal is due for completion by mid-1993, subject to regulatory approvals. BASF, hitherto a small-scale PP producer, doubles capacity to 600,000 m.t./year and moves up the European PP league to number three, behind Himont and Shell. BASF, whose process is used in the plants, secures a foothold in the UK PP market, where Shell - planning a merger with Himont - is the only other producer, with 170,000 m.t./year. ICI's purchase involves BASF's Resart GmbH and Critesa SA subsidiaries, located at Mainz, Germany and near Barcelona, Spain, respectively. The business - which will add about [Brit pounds]60 million ($93 million) to ICI Acrylics [Brit pounds]300-million revenues - employs 400 people, who will transfer to ICI.

  16. Performance comparison of acrylic and thiol-acrylic resins in two-photon polymerization.

    PubMed

    Jiang, Lijia; Xiong, Wei; Zhou, Yushen; Liu, Ying; Huang, Xi; Li, Dawei; Baldacchini, Tommaso; Jiang, Lan; Lu, Yongfeng

    2016-06-13

    Microfabrication by two-photon polymerization is investigated using resins based on thiol-ene chemistry. In particular, resins containing different amounts of a tetrafunctional acrylic monomer and a tetrafunctional thiol molecule are used to create complex microstructures. We observe the enhancement of several characteristics of two-photon polymerization when using thiol-acrylic resins. Specifically, microfabrication is carried out using higher writing velocities and it produces stronger polymeric microstructures. Furthermore, the amount of shrinkage typically observed in the production of three-dimensional microstructures is reduced also. By means of microspectrometry, we confirm that the thiol-acrylate mixture in TPP resins promote monomer conversion inducing a higher degree of cross-linked network formation.

  17. Performance comparison of acrylic and thiol-acrylic resins in two-photon polymerization.

    PubMed

    Jiang, Lijia; Xiong, Wei; Zhou, Yushen; Liu, Ying; Huang, Xi; Li, Dawei; Baldacchini, Tommaso; Jiang, Lan; Lu, Yongfeng

    2016-06-13

    Microfabrication by two-photon polymerization is investigated using resins based on thiol-ene chemistry. In particular, resins containing different amounts of a tetrafunctional acrylic monomer and a tetrafunctional thiol molecule are used to create complex microstructures. We observe the enhancement of several characteristics of two-photon polymerization when using thiol-acrylic resins. Specifically, microfabrication is carried out using higher writing velocities and it produces stronger polymeric microstructures. Furthermore, the amount of shrinkage typically observed in the production of three-dimensional microstructures is reduced also. By means of microspectrometry, we confirm that the thiol-acrylate mixture in TPP resins promote monomer conversion inducing a higher degree of cross-linked network formation. PMID:27410383

  18. New series of potent delta-opioid antagonists containing the H-Dmt-Tic-NH-hexyl-NH-R motif.

    PubMed

    Li, Tingyou; Shiotani, Kimitaka; Miyazaki, Anna; Fujita, Yoshio; Tsuda, Yuko; Ambo, Akihiro; Sasaki, Yusuke; Jinsmaa, Yunden; Marczak, Ewa; Bryant, Sharon D; Lazarus, Lawrence H; Okada, Yoshio

    2005-12-15

    Heterodimeric compounds H-Dmt-Tic-NH-hexyl-NH-R (R=Dmt, Tic, and Phe) exhibited high affinity to delta- (K(i)delta=0.13-0.89nM) and mu-opioid receptors (K(i)mu=0.38-2.81nM) with extraordinary potent delta antagonism (pA(2)=10.2-10.4). These compounds represent the prototype for a new class of structural homologues lacking mu-opioid receptor-associated agonism (IC(50)=1.6-5.8muM) based on the framework of bis-[H-Dmt-NH]-alkyl (Okada, Y.; Tsuda, Y.; Fujita, Y.; Yokoi, T.; Sasaki, Y.; Ambo, A.; Konishi, R.; Nagata, M.; Salvadori, S.; Jinsmaa, Y.; Bryant, S. D.; Lazarus, L. H. J. Med. Chem.2003, 46, 3201), which exhibited both high mu affinity and bioactivity.

  19. Crystal structure of 3-benzyl-1-[(cyclo­hexyl­idene)amino]­thio­urea

    PubMed Central

    Mohamed, Shaaban K.; Mague, Joel T.; Akkurt, Mehmet; Hassan, Alaa A.; Abdel-Aziz, Ahmed T.; Albayati, Mustafa R.

    2015-01-01

    The conformation of the title compound, C14H19N3S, is partially determined by an intra­molecular N—H⋯N hydro­gen-bond inter­action, although the N—H⋯N angle of 108° is quite small. The cyclo­hexyl­idene ring has a chair conformation and its mean plane is inclined to the benzene ring by 46.30 (8)°. In the crystal, mol­ecules are linked by pairs of N—H⋯S hydrogen bonds, forming inversion dimers, with an R 2 2(8) ring motif. The dimers are reinforced by pairs of C—H⋯S hydrogen bonds, and are linked by further weak C—H⋯S hydrogen bonds, forming chains propagating along [100]. PMID:26870535

  20. Degradation of organic ultraviolet filter diethylamino hydroxybenzoyl hexyl benzoate in aqueous solution by UV/H2O2.

    PubMed

    Gong, Ping; Yuan, Haixia; Zhai, Pingping; Dong, Wenbo; Li, Hongjing

    2015-07-01

    Steady-state and transient-state photolysis experiments were conducted to investigate the degradation of organic ultraviolet filter diethylamino hydroxybenzoyl hexyl benzoate (DHHB) in the aqueous solution by UV/H2O2. Results showed that the obvious degradation of DHHB was not observed under UV irradiation (λ = 254 nm), and the DHHB degradation was conducted due to the oxidation by hydroxyl radical (HO·). While the H2O2 concentration was between 0.05 and 0.10 mol L(-1), the highest DHHB degradation efficiency was obtained. The lower solution pH favored the transformation of DHHB, and the coexisting Cl(-) and NO3(-) ions slightly enhanced the conversion. The degradation of DHHB by HO· followed a pseudo-first-order kinetic model with different initial DHHB concentrations. By intermediate products during DHHB oxidation and laser flash photolysis spectra analysis, a primary degradation pathway was proposed.

  1. Palladium (Ii) Catalyzed Polymerization Of Norbornene And Acrylates

    DOEpatents

    Sen, Ayusman; Kacker, Smita; Hennis, April; Polley, Jennifer D.

    2001-10-09

    Homopolymers or copolymers of acrylates, homopolymers or copolymers of norbornenes, and copolymers of acrylates with norbornenes, may be prepared by contacting acrylate and/or norbornene monomer reactant under polymerization conditions and in the presence of a solvent with a catalyst system consisting essentially of a Pd(II) dimer component having the formula: where L is a monodentate phosphorus or nitrogen ligand, X is an anionic group, and R is an alkyl or aryl group.

  2. Palladium (II) catalyized polymerization of norbornene and acrylates

    DOEpatents

    Sen, Ayusman; Kacker, Smita; Hennis, April; Polley, Jennifer D.

    2000-08-29

    Homopolymers or copolymers of acrylates, homopolymers or copolymers of norbornenes, and copolymers of acrylates with norbornenes, may be prepared by contacting acrylate and/or norbornene monomer reactant under polymerization conditions and in the presence of a solvent with a catalyst system consisting essentially of a Pd(II) dimer component having the formula: [(L)Pd(R)(X)].sub.2, where L is a monodentate phosphorus or nitrogen ligand, X is an anionic group, and R is an alkyl or aryl group.

  3. Pulse radiolysis of aqueous solutions of ethyl acrylate and hydroxy ethyl acrylate

    NASA Astrophysics Data System (ADS)

    Safrany, A.; Biro, A.; Wojnarovits, L.

    1993-10-01

    Ethyl- and hydroxy ethyl acrylate show high reactivities with hydrated electron and hydroxyl radical intermediates of water radiolysis. The electron adduct reversibly protonate with pK values of 5.7 and 7.3. The adducts may take part in irreversible protonation at the β carbon atom forming α-carboxyl alkyl radicals. Same type of radical forms in reaction of acrylates with OH: at low concentration the adduct mainly disappear in self termination reactions. Above 5 mmol dm -1 the signals showed the startup of oligomerization.

  4. Severe Onychodystrophy due to Allergic Contact Dermatitis from Acrylic Nails

    PubMed Central

    Mattos Simoes Mendonca, Marcela; LaSenna, Charlotte; Tosti, Antonella

    2015-01-01

    Acrylic nails, including sculptured nails and the new ultraviolet-curable gel polish lacquers, have been associated with allergic contact dermatitis (ACD). We report 2 cases of ACD to acrylic nails with severe onychodystrophy and psoriasiform changes including onycholysis and subungual hyperkeratosis. In both cases, the patients did not realize the association between the use of acrylate-based manicures and nail changes. One patient had been previously misdiagnosed and treated unsuccessfully for nail psoriasis. The informed clinician should elicit a history of acrylic manicure in patients with these nail changes, especially in cases of suspected nail psoriasis refractory to treatment. Patch testing is a useful tool in confirming diagnosis. PMID:27170940

  5. Severe Onychodystrophy due to Allergic Contact Dermatitis from Acrylic Nails.

    PubMed

    Mattos Simoes Mendonca, Marcela; LaSenna, Charlotte; Tosti, Antonella

    2015-09-01

    Acrylic nails, including sculptured nails and the new ultraviolet-curable gel polish lacquers, have been associated with allergic contact dermatitis (ACD). We report 2 cases of ACD to acrylic nails with severe onychodystrophy and psoriasiform changes including onycholysis and subungual hyperkeratosis. In both cases, the patients did not realize the association between the use of acrylate-based manicures and nail changes. One patient had been previously misdiagnosed and treated unsuccessfully for nail psoriasis. The informed clinician should elicit a history of acrylic manicure in patients with these nail changes, especially in cases of suspected nail psoriasis refractory to treatment. Patch testing is a useful tool in confirming diagnosis. PMID:27170940

  6. Spectroscopic (FT-IR and UV-Vis) and theoretical (HF and DFT) investigation of 2-Ethyl-N-[(5-nitrothiophene-2-yl)methylidene]aniline

    NASA Astrophysics Data System (ADS)

    Ceylan, Ümit; Tarı, Gonca Özdemir; Gökce, Halil; Ağar, Erbil

    2016-04-01

    Crystal structure of the title compound, 2-Ethyl-N-[(5-nitrothiophene-2-yl)methylidene]aniline, C13H12N2O2S, has been synthesized and characterized by FT-IR and UV-Vis spectrum. The compound crystallized in the monoclinic space group P 21/c with a = 11.3578 (4) Å, b = 7.4923 (2) Å, c = 14.9676 (6) Å and β = 99.589 (3)° and Z = 4 in the unit cell. The molecular geometry was also calculated using the Gaussian 03 software and structure was optimized using the HF and DFT/B3LYP methods with the 6-311++G(d,p) basis set in ground state. Using the TD-DFT method, the electronic absorption spectra of the title compound was computed in both the gas phase and ethanol solvent. The harmonic vibrational frequencies of the title compound were calculated using the same methods with the 6-311++G(d,p) basis set. The calculated results were compared with the experimental determination results of the compound. It was seen that the optimized structure was in excellent agreement with the X-ray crystal structure. The energetic behaviors of the title compound in solvent media were examined using the HF and DFT/B3LYP methods with the 6-311++G(d,p) basis set applying the polarizable continuum model (PCM). In addition, the molecular orbitals (FMOs) analysis, molecular electrostatic potential (MEP), nonlinear optical and thermodynamic properties of the title compound were performed using the same methods with the 6-311++G(d,p) basis set.

  7. Subchronic inhalation exposure to 2-ethyl-1-hexanol impairs the mouse olfactory bulb via injury and subsequent repair of the nasal olfactory epithelium.

    PubMed

    Miyake, Mio; Ito, Yuki; Sawada, Masato; Sakai, Kiyoshi; Suzuki, Himiko; Sakamoto, Tatsuo; Sawamoto, Kazunobu; Kamijima, Michihiro

    2016-08-01

    The olfactory system can be a toxicological target of volatile organic compounds present in indoor air. Recently, 2-ethyl-1-hexanol (2E1H) emitted from adhesives and carpeting materials has been postulated to cause "sick building syndrome." Patients' symptoms are associated with an increased sense of smell. This investigation aimed to characterize the histopathological changes of the olfactory epithelium (OE) of the nasal cavity and the olfactory bulb (OB) in the brain, due to subchronic exposure to 2E1H. Male ICR mice were exposed to 0, 20, 60, or 150 ppm 2E1H for 8 h every day for 1 week, or 5 days per week for 1 or 3 months. After a 1-week exposure, the OE showed inflammation and degeneration, with a significant concentration-dependent reduction in the staining of olfactory receptor neurons and in the numbers of globose basal cells at ≥20 ppm. Regeneration occurred at 1 month along with an increase in the basal cells, but lymphocytic infiltration, expanded Bowman's glands, and a decrease in the olfactory receptor neurons were observed at 3 months. Intriguingly, the OB at 3 months showed a reduction in the diameters of the glomeruli and in the number of olfactory nerves and tyrosine hydroxylase-positive neurons, but an increased number of ionized calcium-binding adaptor molecule 1-positive microglia in glomeruli. Accordingly, 2E1H inhalation induced degeneration of the OE with the lowest-observed-adverse-effect level of 20 ppm. The altered number of functional cell components in the OB suggests that effects on olfactory sensation persist after subchronic exposure to 2E1H. PMID:27055686

  8. Annual transition and seasonal variation of indoor air pollution levels of 2-ethyl-1-hexanol in large-scale buildings in Nagoya, Japan.

    PubMed

    Sakai, Kiyoshi; Kamijima, Michihiro; Shibata, Eiji; Ohno, Hiroyuki; Nakajima, Tamie

    2009-11-01

    2-Ethyl-1-hexanol (2E1H) is a possible causative chemical for sick building symptoms; however, thus far, we do not have a clear understanding of the indoor air pollution levels caused by it. In this study, first, airborne 2E1H concentrations were measured during summer and winter from 2004 to 2007 in 67 rooms of 56 large-scale buildings in Nagoya, Japan, in order to show the seasonal variation of indoor air pollution levels of 2E1H. Then, a follow-up survey was conducted in five rooms of five buildings for more than 2 years in order to establish the annual transition of their 2E1H indoor air pollution levels. 2E1H was found to be one of the predominant volatile organic compounds in the indoor air of large-scale buildings. Its geometric mean concentration was significantly higher during summer (55.4 microg/m3) than during winter (13.7 microg/m3) (p < 0.01), although there was a significant difference in the concentrations among the buildings. High 2E1H concentrations may have been caused by high emission rates of 2E1H from floors, because of the hydrolysis of di(2-ethylhexyl) phthalate in polyvinyl chloride flooring materials or of adhesives containing 2-ethylhexyl moieties. Follow-up observations showed little decrease in the indoor air 2E1H concentrations from one year to the next, although they did show seasonal fluctuations, with an evident increase in concentrations during summer and an evident decrease during winter. PMID:19890564

  9. Acrylic Finger Prosthesis: A Case Report

    PubMed Central

    Bandela, Vinod; M, Bharathi; S V, Giridhar Reddy

    2014-01-01

    Hands basic function is to grasp, hold and manipulate items. Hand gesture is perhaps the most blatant example of non-verbal communication. Finger and partial finger amputations are most frequently encountered forms of partial hand loss. Common causes are traumatic injuries, congenital absence or malformations present great clinical challenges. In addition to immediate loss of grasp strength, finger absence may cause marked psychological trauma. Individuals who desire finger replacement usually have high expectation for the appearance of prosthesis. This clinical report portrays simple method to retain acrylic finger prosthesis. PMID:25302271

  10. Junction-Controlled Elasticity of Single-Walled Carbon Nanotube Dispersions in Acrylic Copolymer Gels and Solutions

    SciTech Connect

    Schoch, Andrew B.; Shull, Kenneth R.; Brinson, L. Catherine

    2008-08-26

    Oscillatory shear rheometry is used to study the mechanical response of single-walled carbon nanotubes dispersed in solutions of acrylic diblock or triblock copolymers in 2-ethyl-1-hexanol. Thermal transitions in the copolymer solutions provide a route for the easy processing of these composite materials, with excellent dispersion of the nanotubes as verified by near-infrared photoluminescence spectroscopy. The nanotube dispersions form elastic networks with properties that are controlled by the junction points between nanotubes, featuring a temperature-dependent elastic response that is controlled by the dynamic properties of the matrix copolymer solution. The data are consistent with the formation of micelle-like aggregates around the nanotubes. At low temperatures the core-forming poly(methyl methacrylate) blocks are glassy, and the overall mechanical response of the composite does not evolve with time. At higher temperatures the enhanced mobility of the core-forming blocks enables the junctions to achieve more intimate nanotube-nanotube contact, and the composite modulus increases with time. These aging effects are observed in both diblock and triblock copolymer solutions but are partially reversed in the triblock solutions by cooling through the gel transition of the triblock copolymer. This result is attributed to the generation of internal stresses during gelation and the ability of these stresses to break or weaken the nanotube junctions.

  11. 40 CFR 721.10500 - Acrylated mixed metal oxides (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Acrylated mixed metal oxides (generic... Specific Chemical Substances § 721.10500 Acrylated mixed metal oxides (generic). (a) Chemical substance and... mixed metal oxides (PMN P-06-341) is subject to reporting under this section for the significant...

  12. 40 CFR 721.10500 - Acrylated mixed metal oxides (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Acrylated mixed metal oxides (generic... Specific Chemical Substances § 721.10500 Acrylated mixed metal oxides (generic). (a) Chemical substance and... mixed metal oxides (PMN P-06-341) is subject to reporting under this section for the significant...

  13. 40 CFR 721.8082 - Polyester polyurethane acrylate.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Polyester polyurethane acrylate. 721... Substances § 721.8082 Polyester polyurethane acrylate. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as polyester polyurethane...

  14. 40 CFR 721.8082 - Polyester polyurethane acrylate.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Polyester polyurethane acrylate. 721... Substances § 721.8082 Polyester polyurethane acrylate. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as polyester polyurethane...

  15. 40 CFR 721.8082 - Polyester polyurethane acrylate.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Polyester polyurethane acrylate. 721... Substances § 721.8082 Polyester polyurethane acrylate. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as polyester polyurethane...

  16. 40 CFR 721.8082 - Polyester polyurethane acrylate.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Polyester polyurethane acrylate. 721... Substances § 721.8082 Polyester polyurethane acrylate. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as polyester polyurethane...

  17. 40 CFR 721.8082 - Polyester polyurethane acrylate.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Polyester polyurethane acrylate. 721... Substances § 721.8082 Polyester polyurethane acrylate. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as polyester polyurethane...

  18. The Acrylation of Glycerol: a Precursor to Functionalized Lipids

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Didecanoylacryloylglycerol was synthesized from decanoic and acrylic acids and glycerol using K2O as catalyst. This reaction was carried out in hexane in a closed stainless steel reactor at 200°C for 5h. The reactants were added in a 1:3:4 glycerol:decanoic acid:acrylic acid molar ratio. The resu...

  19. 40 CFR 721.10307 - Acrylate resin (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Acrylate resin (generic). 721.10307 Section 721.10307 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10307 Acrylate resin...

  20. 40 CFR 721.330 - Aromatic acrylate (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.330 Aromatic acrylate (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as an aromatic acrylate (PMN P-01-420)...

  1. 40 CFR 721.330 - Aromatic acrylate (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.330 Aromatic acrylate (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as an aromatic acrylate (PMN P-01-420)...

  2. Neurotoxicological and thyroid evaluations of rats developmentally exposed to tris(1,3-dichloro-2-propyl)phosphate (TDCIPP) and tris(2-chloro-2-ethyl)phosphate (TCEP).

    PubMed

    Moser, Virginia C; Phillips, Pamela M; Hedge, Joan M; McDaniel, Katherine L

    2015-01-01

    Tris(1,3-dichloro-2-propyl)phosphate (TDCIPP) and tris(2-chloro-2-ethyl)phosphate (TCEP) are organophosphorous flame retardants with widespread usage and human exposures through food, inhalation, and dust ingestion. They have been detected in human tissues including urine and breast milk. Reports of disrupted neural growth in vitro, abnormal development in larval zebrafish, and altered thyroid hormones in several species have raised concern for neurodevelopmental toxicity. This is especially the case for TDCIPP, which is more potent and has more activity in those assays than does TCEP. We evaluated the potential for developmental neurotoxicity of TDCIPP and TCEP in a mammalian model. Pregnant Long-Evans rats were administered TDCIPP (15, 50, or 150 mg/kg/day) or TCEP (12, 40, 90 mg/kg/day) via oral gavage from gestational day 10 to weaning. Corn oil was the vehicle control in both studies. Body weight and righting reflex development were monitored in all pups. A subset of offspring at culling and weaning, and dams at weaning, were sacrificed for serum and organ collection for measurement of brain, liver, and thyroid weights, serum thyroid levels, and serum and brain acetylcholinesterase activities. Brain weights were also measured in a group of adult TDCIPP-treated offspring. One male and one female from each litter were allocated for behavioral testing at several ages: standard locomotor activity (preweaning, postweaning, adults), locomotor activity including a lighting change mid-way (postweaning, adults), elevated zero maze (postweaning, adults), functional observational battery (FOB; postweaning, adults), and Morris water maze (place learning, reference and working memory; adults). Neither chemical produced changes in maternal body weight or serum thyroid hormones, but relative liver weight was increased at the high doses of both TDCIPP and TCEP. In offspring, there were no effects on viability, litter size, or birth weight. With TDCIPP, absolute liver weights

  3. Leukotriene C4 induces bronchoconstriction and airway vascular hyperpermeability via the cysteinyl leukotriene receptor 2 in S-hexyl glutathione-treated guinea pigs.

    PubMed

    Yonetomi, Yasuo; Sekioka, Tomohiko; Kadode, Michiaki; Kitamine, Tetsuya; Kamiya, Akihiro; Matsumura, Naoya; Fujita, Manabu; Kawabata, Kazuhito

    2015-05-01

    Cysteinyl leukotrienes act through G-protein-coupled receptors termed cysteinyl leukotriene 1 (CysLT1) and cysteinyl leukotriene 2 (CysLT2) receptors. However, little is known about the pathophysiological role of CysLT2 receptors in asthma. To elucidate the possible involvement of CysLT2 receptors in bronchoconstriction and airway vascular hyperpermeability, we have established a novel guinea pig model of asthma. In vitro study confirmed that CHO-K1 cells, expressing guinea pig CysLT2 and CysLT1 receptors are selectively stimulated by LTC4 and LTD4, respectively. However, when LTC4 was intravenously injected to guinea pigs, the resulting bronchoconstriction was fully abrogated by montelukast, a CysLT1 receptor antagonist, indicating rapid metabolism of LTC4 to LTD4 in the lung. We found that treatment with S-hexyl glutathione (S-hexyl GSH), an inhibitor of gamma-glutamyl transpeptidase, significantly increased LTC4 content and LTC4/(LTD4 plus LTE4) ratio in the lung. Under these circumstances, LTC4-induced bronchoconstriction became resistant to montelukast, but sensitive to Compound A, a CysLT2 receptor antagonist, depending on the dose of S-hexyl GSH. Combination with montelukast and Compound A completely abrogated this spasmogenic response. Additionally, we confirmed that LTC4 elicits airway vascular hyperpermeability via CysLT2 receptors in the presence of high dose of S-hexyl GSH as evidenced by complete inhibition of LTC4-induced hyperpermeability by Compound A, but not montelukast. These results suggest that CysLT2 receptors mediate bronchoconstriction and airway vascular hyperpermeability in guinea pigs and that the animal model used in this study may be useful to elucidate the functional role of CysLT2 receptors in various diseases, including asthma. PMID:25704617

  4. Diallyl 5-[(4-hexyl­oxyphen­yl)imino­meth­yl]-m-phenyl­ene dicarbonate

    PubMed Central

    Herrera-González, Ana María; López-Velázquez, Delia; Bernès, Sylvain

    2009-01-01

    The title mol­ecule, C27H31NO7, an imine derivative bearing both carbonate and allyl functionalities, was synthesized in the hope of obtaining a mesogenic polymerizable material. The allyl­carbonate arms are fully disordered over two sets of sites, reflecting a large degree of rotational freedom about σ bonds [occupancies: 0.665 (9)/0.335 (9) for one substituent, 0.564 (9)/0.436 (9) for the other]. In contrast, the hexyl chain is ordered, and presents the common all-trans extended conformation. The benzene rings connected via the imine group make a dihedral angle of 9.64 (11)°. In the crystal, the Y-shaped mol­ecules are weakly associated into centrosymmetric dimers through pairs of C—H⋯O(hex­yl) contacts. The resulting layers of dimers, approximately parallel to (25), are closely packed in the crystal, allowing π⋯π inter­actions between benzene rings of neighboring layers: the separation between the centroid of the benzene ring substituted by allyl­carbonate and the centroid of the benzene ring bearing the hex­yloxy group in the adjacent layer is 3.895 (1) Å. PMID:21578402

  5. Biological responses of Vicia faba seedlings to the imidazolium-based ionic liquid 1-hexyl-3-methylimidazolium chloride in soil.

    PubMed

    Liu, Tong; Wang, Jinhua; Wang, Jun; Zhu, Lusheng; Zhang, Jun

    2016-06-01

    Although there are a few studies on the toxicity of ionic liquids (ILs), relatively little is known about their toxic effects on plants in soil. In the present study, the toxic effects of 1-hexyl-3-methylimidazolium chloride ([Hmim]Cl) in the soil on Vicia faba seedlings and the influences of [Hmim]Cl on the physicochemical properties of the soil were studied. Organic matter content, pH, and conductivity of the tested soil were significantly altered at [Hmim]Cl concentrations greater than 1000 mg kg(-1) . Moreover, shoot length, root length, dry weight, and pigment content of the V. faba seedlings were greatly inhibited when the [Hmim]Cl concentration was greater than 500 mg kg(-1) . The roots were the most seriously affected organ and stopped growing at 3000 mg kg(-1) . In addition, [Hmim]Cl caused an increase in the level of reactive oxygen species at [Hmim]Cl concentrations above 250 mg kg(-1) that resulted in lipid peroxidation, DNA damage, and oxidative stress in the V. faba seedlings. The present study provides information that is useful for evaluation of the environmental safety of ILs in soil. Environ Toxicol Chem 2016;35:1502-1510. © 2015 SETAC. PMID:26517735

  6. Thermal and optical characterization of liquid crystal 4‧-hexyl-4-biphenylcarbonitrile/4-hexylbenzoic acid mixtures

    NASA Astrophysics Data System (ADS)

    Okumuş, Mustafa; Özgan, Şükrü; Kırık, İhsan; Kerli, Süleyman

    2016-09-01

    We present the thermal and optical properties of binary mixtures formed from hydrogen-bonded liquid crystal 4-hexylbenzoic acid (6BA) and 4-hexyl-4‧-biphenylcarbonitrile (6CB) mesogens. Phase transition temperatures and enthalpy values are evaluated by differential scanning calorimetry (DSC) and phases identified by polarized optic microscopy (POM). The experimental results obviously show that the 6BA/6CB binary mixtures exhibit nematic and smectic phases. The most interesting result is that although the smectic phase is not observed in pure components 6BA and 6CB, it is observed in their some binary mixtures. The thermal properties like phase peak temperatures, enthalpy changes and thermal span of binary mixtures are affected by depending on the mixture ratio. The nematic range increase in the binary mixture compared to the individual mesogen, and also the phase transition temperature values and the nematic thermal stability factor increase as heating rate increases. Furthermore, the calculated activation energy values show that the reorientation of the molecules during the phase transitions of the mixture occurs on an orderly basis.

  7. Determination of the Crystallinity of Semicrystalline Poly(3-hexyl thiophene) by Means of Wide Angle X-Ray Scattering

    NASA Astrophysics Data System (ADS)

    Balko, Jens; Lohwasser, Ruth; Thelakkat, Mukundan; Sommer, Michael; Pascui, Ovidiu; Saalwaechter, Kay; Thurn-Albrecht, Thomas

    2013-03-01

    Poly(3-hexyl thiophene) (P3HT) is a common polymer semiconductor, often used as material or component in organic field effect transistors or solar cells. The crystallinity of this semicrystalline material is among other parameters governing the electronic mobility. However, at present there is no routine method available to determine an absolute value for the crystallinity, and the values given in the literature e.g. for the enthalpy of melting vary by a factor of three. Wide Angle X-Ray Scattering (WAXS) probes the crystals as well the amorphous parts of the sample. We present an approach for the determination of the crystallinity based on the evaluation of WAXS intensities at low scattering vectors emanating from the amorphous regions. The result is used for a calibration of the melting enthalpy (34 J/g) that can serve as a reference value for more convenient calorimetric techniques and compared to the results of recent NMR investigations. We discuss the crystallinity for a number of chemically well-defined samples, with different molecular weight and a typical commercial sample with broad molecular weight distribution. Despite the high crystallinities of 60 to 80% the crystallites exhibit a large amount of disorder.

  8. Tailoring ultrasound-induced growth of perylene diimide nanowire crystals from solution by modification with poly(3-hexyl thiophene).

    PubMed

    Bu, Laju; Dawson, Trenton J; Hayward, Ryan C

    2015-02-24

    Tailoring nanocrystalline morphologies of organic semiconductors holds importance for organic electronics due to the influence of crystal characteristics on optoelectronic properties. Soluble additives that control crystal growth are commonly found in a variety of contexts such as biomineralization, pharmaceutical processing, and food science, while the use of ultrasound to modify crystal nucleation and growth has been routinely employed in producing crystals of food ingredients, biomolecules, pharmaceuticals, and inorganic materials. However, both methods have been applied to the growth of organic semiconductor crystals only in limited fashion. Here, we combine these two approaches to show that colloidally stable nanowire suspensions of a n-type small molecule, perylene diimide (PDI), can be prepared with well-controlled structures by sonocrystallization in the presence of a p-type polymer, poly(3-hexyl thiophene) (P3HT), as a soluble additive. By preferentially adsorbing on lateral crystal faces, P3HT dramatically reduces PDI crystal growth rate in the lateral directions relative to that along the nanowire axis, yielding nanocrystals with widths below 20 nm and narrow width distributions. With the use of uniform short PDI nanowires as seeds and extension with metastable solutions, controlled growth of PDI nanowires by "living crystallization" is demonstrated, providing access to narrowed length distributions and tailored branched crystal morphologies.

  9. [Determination of the thermodynamic parameters of ionic liquid 1-hexyl-3-methylimidazolium tetrafluoroborate by inverse gas chromatography].

    PubMed

    Li, Xiaoping; Wang, Qiang; Li, Ling; Ding, Yanping

    2015-01-01

    Inverse gas chromatography (IGC) was used to characterize the thermodynamic properties of ionic liquid (IL) 1-hexyl-3-methylimidazolium tetrafluoroborate ([HMIM] BF4) in the temperature range from 343.15 K to 373. 15 K. A series of solvents with different chemical natures were used to determine the [HMIM] BF4-solvent interactions. The thermodynamic parameters including Flory-Huggins interaction parameter, partial molar heats of sorption, mixing and evaporation as well as the activity coefficient at infinite dilution were obtained to judge the interactions between [HMIM]BF4 and the selected solvents. In addition, the solubility parameters of [HMIM] BF4 at different temperatures were determined. The results showed that among the selected solvents, n-C6, n-C7, n-C8, n-C9, diethyl ether, tetrahydrofuran, benzene and cyclohexane were poor solvents for [HMIM] BF4, while toluene, m-xylene, methanol, ethanol, dichloromethane, tetrachloromethane, chloroform, acetone, ethyl acetate and methyl acetate were the favorite ones. The solubility parameter of [HMIM]BF4 at room temperature (298.15 K) was 23.70 (J x cm(-3)(0.5), which was obtained by the linear extrapolation method. The experiment proved that IGC is a simple and accurate method to obtain the thermodynamic properties of ionic liquids. The obtained thermodynamic parameters revealed the strength of the interactions between the selected solvents and the ionic liquid, which could be used as a reference to the further applications of the ionic liquid. PMID:25958669

  10. Lipid-associated methylpheophorbide-a (hexyl-ether) as a photodynamic agent in tumor-bearing mice.

    PubMed

    Mayhew, E; Vaughan, L; Panus, A; Murray, M; Henderson, B W

    1993-12-01

    Liposomes are a potential system for more selective delivery of photosensitizers (PS) to tumors. Pheophorbides are one series of new PS under investigation for use in photodynamic therapy. The pharmacokinetics, anti-tumor response and normal tissue effects of methylpheophorbide-a-(hexyl-ether) (MPH) associated with negatively charged phospholipid vesicles composed of high and low transition temperature lipids were determined in mice. In some preparations monosialoganglioside, which is known to impart long circulation time to liposomes was also included. Normally water-insoluble MPH could be quantitatively incorporated in multilamellar liposomes up to at least 20 mol MPH/mol lipid% for most liposome compositions and sonicated to form clear suspensions. Evidence from electron microscopy and entrapment of aqueous space markers indicated that the particles formed by sonication were not standard liposomes. Anti-tumor responses to light treatment (135 J/cm2, 665 nm argon-dye laser) 24 h after MPH (0.4 mumol/kg) administration were slightly but significantly greater (P < 0.05) for lipid associated MPH compared to MPH solubilized in Tween 80. There were no major differences in tumor uptake and tumor cell photosensitization between lipid or Tween 80 formulations of MPH, whereas, dependent on lipid composition and time after MPH administration, the doses of light required to cause occlusive vascular damage were increased for the lipid formulations. Pharmacokinetic studies showed rapid dissociation between lipids and MPH in vivo. Lipid formulations are useful for solubilizing MPH and may improve the therapeutic effects of this PS.

  11. Neuroprotection by 6-(methylsulfinyl)hexyl isothiocyanate in a 6-hydroxydopamine mouse model of Parkinson׳s disease.

    PubMed

    Morroni, Fabiana; Sita, Giulia; Tarozzi, Andrea; Cantelli-Forti, Giorgio; Hrelia, Patrizia

    2014-11-17

    A number of pathogenic factors have been implicated in the progression of Parkinson׳s disease (PD), including oxidative stress, mitochondrial dysfunction, inflammation, excitotoxicity, and signals mediating apoptosis cascade. 6-(methylsulfinyl)hexyl isothiocyanate (6-MSITC) is a major component in wasabi, a very popular spice in Japan and a member of the Brassica family of vegetables. This study was designed to investigate the neuroprotective effects of 6-MSITC in a PD mouse model. Mice were treated with 6-MSITC (5mg/kg twice a week) for four weeks after the unilateral intrastriatal injection of 6-hydroxydopamine (6-OHDA). On the 28th day, 6-OHDA-injected mice showed behavioral impairments, a significant decrease in tyrosine hydroxylase (TH) and an increase in apoptosis. In addition, lesioned mice showed reduced glutathione levels and glutathione-S-transferase and glutathione reductase activities. Notably, 6-MSITC demonstrated neuroprotective effects in our experimental model strongly related to the preservation of functional nigral dopaminergic neurons, which contributed to the reduction of motor dysfunction induced by 6-OHDA. Furthermore, this study provides evidence that the beneficial effects of 6-MSITC could be attributed to the decrease of apoptotic cell death and to the activation of glutathione-dependent antioxidant systems. These findings may render 6-MSITC as a promising molecule for further pharmacological studies on the investigation for disease-modifying treatment in PD. PMID:25257035

  12. Crystal structure of bis-(1-hexyl-N,N-di-methyl-pyridinium) bis-(maleo-nitrile-dithiol-ato)nickelate(II).

    PubMed

    Yu, Shan-Shan; Zhang, Hui

    2016-08-01

    The asymmetric unit of the title compound, (C13H23N2)2[Ni(C4N2S2)2], consists of a 1-hexyl-N,N-di-methyl-pyridinium cation and one half of a [Ni(mnt)2](2-) dianion (mnt(2-) = maleo-nitrile-dithiol-ate) in which the Ni(2+) cation lies on a crystallographic inversion centre. The square-planar coordination about Ni(2+) comprises four S atoms from two bidentate chelate mnt(2-) ligands [Ni-S = 2.1791 (9) and 2.1810 (8) Å, and S-Ni-S bite angle = 91.93 (3)°]. The hydro-carbon chains of cations show trans-planar conformations and lie approximately parallel to the long mol-ecular axis of the [Ni(mnt)2](2-) anions, giving stacks along the c axis. The anions and cations form layers lying parallel to the bc plane. Only weak C-H⋯Ni and C-H⋯π associations are present in the crystal packing. PMID:27536413

  13. 21 CFR 177.1340 - Ethylene-methyl acrylate copolymer resins.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Ethylene-methyl acrylate copolymer resins. 177...-methyl acrylate copolymer resins. Ethylene-methyl acrylate copolymer resins may be safely used as... prescribed conditions: (a) For the purpose of this section, the ethylene-methyl acrylate copolymer...

  14. Electrochemical characterization of aminated acrylic conducting polymer

    SciTech Connect

    Rashid, Norma Mohammad; Heng, Lee Yook; Ling, Tan Ling

    2015-09-25

    New attempt has been made to synthesize aminated acrylic conducting polymer (AACP) using precursor of phenylvinylsulfoxide (PVS). The process was conducted via the integration of microemulsion and photopolymerization techniques. It has been utilized for covalent immobilization of amino groups by the adding of N-achryiloxisuccinimide (NAS). Thermal eliminating of benzene sulfenic acids from PVS has been done at 250 °C to form electroactive polyacetylene (PA) segment. Characterization of AACP has been conducted using fourier transform infrared (FTIR), scanning electron microscopy (SEM) and linear sweep cyclic voltammetry (CV). A range of 0.3-1.25μm particle size obtained from SEM characterization. A quasi-reversible system performed as shown in electrochemical study.

  15. Electrochemical characterization of aminated acrylic conducting polymer

    NASA Astrophysics Data System (ADS)

    Rashid, Norma Mohammad; Heng, Lee Yook; Ling, Tan Ling

    2015-09-01

    New attempt has been made to synthesize aminated acrylic conducting polymer (AACP) using precursor of phenylvinylsulfoxide (PVS). The process was conducted via the integration of microemulsion and photopolymerization techniques. It has been utilized for covalent immobilization of amino groups by the adding of N-achryiloxisuccinimide (NAS). Thermal eliminating of benzene sulfenic acids from PVS has been done at 250 °C to form electroactive polyacetylene (PA) segment. Characterization of AACP has been conducted using fourier transform infrared (FTIR), scanning electron microscopy (SEM) and linear sweep cyclic voltammetry (CV). A range of 0.3-1.25μm particle size obtained from SEM characterization. A quasi-reversible system performed as shown in electrochemical study.

  16. Flexible, stretchable electroadhesives based on acrylic elastomers

    NASA Astrophysics Data System (ADS)

    Duduta, Mihai; Wood, Robert J.; Clarke, David R.

    2016-04-01

    Controllable adhesion is a requirement for a wide variety of applications including robotic manipulation, as well as locomotion including walking, crawling and perching. Electroadhesives have several advantages such as reversibility, low power consumption and controllability based on applied voltage. Most demonstrations of electroadhesive devices rely on fairly rigid materials, which cannot be stretched reversibly, as needed in some applications. We have developed a fast and reliable method for building soft, stretchable electroadhesive pads based on acrylic elastomers and electrodes made of carbon nanotubes. The devices produced were tested pre-deformation and in a stretched configuration. The adhesive force was determined to be in the 0.1 - 3.0 N/cm2 range, depending on the adhering surface. The electroadhesive devices were integrated with pre-stretched dielectric elastomer actuators to create a device in which the adhesion force could be tuned by changes in either the applied voltage or total area.

  17. Custom cranioplasty using stereolithography and acrylic.

    PubMed

    D'Urso, P S; Earwaker, W J; Barker, T M; Redmond, M J; Thompson, R G; Effeney, D J; Tomlinson, F H

    2000-04-01

    Numerous methods of cranioplasty have been described. Customization and prefabrication have been reported to reduce operating time and improve cosmesis. An original technique for the manufacture of customized cranioplastic implants has been developed and tested in 30 patients.Thirty patients requiring cranioplasties were selected. Data acquired from computed tomography (CT) were used to manufacture exact plastic replicas (biomodels) of craniotomy defects and master cranioplastic implants using the rapid prototyping technology of stereolithography (SL). The three-dimensional (3D) imaging techniques of mirroring and interpolation were used to extrapolate on existing anatomy to design the master implants. The master implants were hand finished to fit the defect in the corresponding cranial biomodel exactly and were then used to create a cavity mould. The mould was used to cast thermally polymerised custom acrylic implants. The surgeons reported that the customized implants reduced operating time, afforded excellent cosmesis and were cost effective. The patients reported that the opportunity to see the biomodel and implant preoperatively improved their understanding of the procedure. Two complications were noted, one infection and one implant required significant trimming. The simultaneous manufacture of the master implant (male) and biomodel (female) components from SL allowed custom accurate implants to be manufactured. Disadvantages identified were the time required for computer manipulations of the CT data (up to 2 h), difficulty in assessing the accuracy of the computer generated master as a 3D rendering, the potential for SL parts to warp, manufacturing time (minimum 2 days) and the cost of approximately $1300 US per case ($1000 for the SL biomodel and $300 for the acrylic casting). PMID:10738323

  18. Poly(amide-graft-acrylate) interfacial compounds

    NASA Astrophysics Data System (ADS)

    Zamora, Michael Perez

    Graft copolymers with segments of dissimilar chemistries have been shown to be useful in a variety of applications as surfactants, compatibilizers, impact modifiers, and surface modifiers. The most common route to well defined graft copolymers is through the use of macromonomers, polymers containing a reactive functionality and thus capable of further polymerization. However, the majority of the studies thus far have focused on the synthesis of macromonomers capable of reacting with vinyl monomers to form graft copolymers. This study focused on the synthesis of macromonomers capable of participating in condensation polymerizations. A chain transfer functionalization method was utilized. Cysteine was evaluated as a chain transfer agent for the synthesis of amino acid functionalized poly(acrylate) and poly(methacrylate) macromonomers. Low molar mass, functionalized macromonomers were produced. These macromonomers were proven to be capable of reacting with amide precursors to form poly(amide-g-acrylate) graft copolymers. Macromonomers and graft copolymers were characterized by gel permeation chromatography (GPC), Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance (NMR) spectroscopy, elemental analysis (EA), inductively coupled plasma (ICP), and differential scanning calorimetry (DSC). The second part of this research involved poly(dimethacrylate) dental restorative materials. Volumetric shrinkage during the cure of these resins results in a poor interface between the resin and the remaining tooth structure, limiting the lifetime of these materials. Cyclic anhydrides were incorporated into common monomer compositions used in dental applications. Volume expansion from the ring opening hydrolysis of these anhydrides was shown to be feasible. The modified dental resins were characterized by swelling, extraction and ultraviolet spectroscopy (UV), and density measurements. Linear poLymers designed to model the crosslinked dental resins were

  19. Conversion of Lignocellulosic Biomass to Ethanol and Butyl Acrylate

    SciTech Connect

    Binder, Thomas; Erpelding, Michael; Schmid, Josef; Chin, Andrew; Sammons, Rhea; Rockafellow, Erin

    2015-04-10

    Conversion of Lignocellulosic Biomass to Ethanol and Butyl Acrylate. The purpose of Archer Daniels Midlands Integrated Biorefinery (IBR) was to demonstrate a modified acetosolv process on corn stover. It would show the fractionation of crop residue to distinct fractions of cellulose, hemicellulose, and lignin. The cellulose and hemicellulose fractions would be further converted to ethanol as the primary product and a fraction of the sugars would be catalytically converted to acrylic acid, with butyl acrylate the final product. These primary steps have been demonstrated.

  20. Investigation of Acrylic Acid at High Pressure Using Neutron Diffraction

    PubMed Central

    2014-01-01

    This article details the exploration of perdeuterated acrylic acid at high pressure using neutron diffraction. The structural changes that occur in acrylic acid-d4 are followed via diffraction and rationalized using the Pixel method. Acrylic acid undergoes a reconstructive phase transition to a new phase at ∼0.8 GPa and remains molecular to 7.2 GPa before polymerizing on decompression to ambient pressure. The resulting product is analyzed via Raman and FT-IR spectroscopy and differential scanning calorimetry and found to possess a different molecular structure compared with polymers produced via traditional routes. PMID:24650085

  1. Methods for the synthesis of deuterated acrylate salts

    SciTech Connect

    Yang, Jun; Bonnesen, Peter V.; Hong, Kunlun

    2014-09-09

    A method for synthesizing a deuterated acrylate of the Formula (1), the method comprising: (i) deuterating a propiolate compound of Formula (2) to a methyne-deuterated propiolate compound of Formula (3) in the presence of a base and D.sub.2O: and (ii) reductively deuterating the methyne-deuterated propiolate compound of Formula (3) in a reaction solvent in the presence of deuterium gas and a palladium-containing catalyst to afford the deuterated acrylate of the Formula (1). The resulting deuterated acrylate compounds, derivatives thereof, and polymers derived therefrom are also described.

  2. A simple solubility tests for the discrimination of acrylic and modacrylic fibers.

    PubMed

    Suga, Keisuke; Narita, Yuji; Suzuki, Shinichi

    2014-05-01

    In a crime scene investigation, single fibers play an important role as significant trace physical evidence. Acrylic fibers are frequently encountered in forensic analysis. Currently, acrylic and modacrylic are not discriminated clearly in Japan. Only results of FT-IR, some of acrylics were difficult to separate clearly to acrylic and modacrylic fibers. Solubility test is primitive but convenient useful method, and Japan Industrial Standards (JIS) recommends FT-IR and solubility test to distinguish acrylic and modacrylic fibers. But recommended JIS dissolving test using 100% N,N-dimethylformamide (DMF) as a solvent, some acrylics could not be discriminated. In this report, we used DMF and ethanol (90:10, v/v) solvent. The JIS method could not discriminate 6 acrylics in 60 acrylics; hence, DMF and ethanol (90:10, v/v) solvent discriminated 59 of the 60 fibers (43 acrylic and 16 modacrylic fibers) clearly, but only one modacrylic fiber incorrectly identified as acrylic.

  3. [Determination of 9 residual acrylic monomers in acrylic resins by gas chromatography-mass spectrometry coupled with microwave assisted extraction].

    PubMed

    Lai, Ying; Lin, Rui; Cai, Luxin; Ge, Xiuxiu; Huang, Changchun

    2012-01-01

    A reliable gas chromatography-mass spectrometry (GC-MS) method was developed for the determination of 9 residual acrylic monomers (methyl acrylate, ethyl acrylate, methyl methacrylate, ethyl methacrylate, n-butyl acrylate, butyl methacrylate, styrene, acrylic acid and methacrylic acid) in acrylic resins. Solid resin was precipitated with methanol after microwave assisted extraction with ethyl acetate for 30 min, and liquid resin was diluted with methanol directly. The nine acrylic monomers got a good separation within 20 min on a DB-WAX column. The limits of quantification (LOQs, S/N = 10) of the method were in the range of 1-10 mg/kg for liquid resin and 3-50 mg/kg for solid resin. The calibration curves were linear within 1-500 mg/L range with correlation coefficients above 0. 995. The recoveries ranged from 84.4% to 108.6% at five spiked levels. The sensitivity, recovery and selectivity of the method can fully meet the requirements of practical work.

  4. [Treatment of acrylate wastewater by electrocatalytic reduction process].

    PubMed

    Yu, Li-Na; Song, Yu-Dong; Zhou, Yue-Xi; Zhu, Shu-Quan; Zheng, Sheng-Zhi; Ll, Si-Min

    2011-10-01

    High-concentration acrylate wastewater was treated by an electrocatalytic reduction process. The effects of the cation exchange membrane (CEM) and cathode materials on acrylate reduction were investigated. It indicated that the acrylate could be reduced to propionate acid efficiently by the electrocatalytic reduction process. The addition of CEM to separator with the cathode and anode could significantly improve current efficiency. The cathode materials had significant effect on the reduction of acrylate. The current efficiency by Pd/Nickel foam, was greater than 90%, while those by nickel foam, the carbon fibers and the stainless steel decreased successively. Toxicity of the wastewater decreased considerably and methane production rate in the biochemical methane potential (BMP) test increased greatly after the electrocatalytic reduction process.

  5. Use of acrylic sheet molds for elastomeric products

    NASA Technical Reports Server (NTRS)

    Heisman, R. M.; Koerner, A. E.; Messineo, S. M.

    1970-01-01

    Molds constructed of acrylic sheet are more easily machined than metal, are transparent to ensure complete filling during injection, and have smooth surfaces free of contamination. Technique eliminates flashing on molded parts and mold release agents.

  6. Performance behavior of modified cellulosic fabrics using polyurethane acrylate copolymer.

    PubMed

    Zuber, Mohammad; Shah, Sayyed Asim Ali; Jamil, Tahir; Asghar, Muhammad Irfan

    2014-06-01

    The surface of the cellulosic fabrics was modified using self-prepared emulsions of polyurethane acrylate copolymers (PUACs). PUACs were prepared by varying the molecular weight of polycaprolactone diol (PCL). The PCL was reacted with isophorone diisocyanate (IPDI) and chain was extended with 2-hydroxy ethyl acrylate (HEA) to form vinyl terminated polyurethane (VTPU) preploymer. The VTPU was further co-polymerized through free radical polymerization with butyl acrylate in different proportions. The FT-IR spectra of monomers, prepolymers and copolymers assured the formation of proposed PUACs structure. The various concentrations of prepared PUACs were applied onto the different fabric samples using dip-padding techniques. The results revealed that the application of polyurethane butyl acrylate copolymer showed a pronounced effect on the tear strength and pilling resistance of the treated fabrics.

  7. Emulsion Polymerization of Butyl Acrylate: Spin Trapping and EPR Study

    NASA Technical Reports Server (NTRS)

    Kim, S.; Westmoreland, D.

    1994-01-01

    The propagating radical in the emulsion polymerization reaction of butyl acrylate was detected by Electron Paramagnetic Resonance spectroscopy using two spin trapping agents, 2-methyl-2nitrosopropane and alpha -N-tert-butylnitrone.

  8. PERMEATION OF MULTIFUNCTIONAL ACRYLATES THROUGH SELECTED PROTECTIVE GLOVE MATERIALS

    EPA Science Inventory

    In support of the Premanufacture Notification (PMN) program of the Environmental Protection Agency's Office of Toxic Substances, the resistance of three glove materials to permeation by multifunctional acrylate compounds was evaluated through a program for the Office of Research ...

  9. Transport Properties of the 1-Hexyl-3-methylimidazolium Bis(trifluoromethylsulfonyl)amide-Trichloromethane Binary System: Indication of Trichloromethane Segregation.

    PubMed

    Saeva, David R; Petenuci, João; Hoffmann, Markus M

    2016-09-15

    Self-diffusion coefficients and electrical conductivity were studied for the binary system 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)amide-trichloromethane ([C6mim][NTf2]-CHCl3) as a function of composition and temperature. Self-diffusion coefficients of cation and anion are identical for ionic liquid mole fractions xIL < 0.95. The self-diffusion coefficient of CHCl3 is consistently larger than that of the ions by a factor of 4. A double logarithmic plot for the ratio of self-diffusion coefficient and temperature versus viscosity is linear for ionic liquid mole fractions 0.1 < xIL < 0.9 indicating (a) a fractional Stokes-Einstein applies where self-diffusion is inverse proportional to some power b of viscosity (D ∼ η(-b)) and (b) single average length scales are associated with the mass transport of [C6mim][NTf2] and CHCl3. However, the obtained length scale for CHCl3 is unreasonably small, which is indicative of CHCl3 segregation. The molar conductivity displays a maximum near xIL = 0.2. Evaluation of the ionicity from molar conductivity and self-diffusion coefficients indicates a gradual speciation change from charged species to neutral species for xIL < 0.5. The temperature dependencies of self-diffusion and molar conductivity follow Arrhenius behavior. The obtained xIL-dependent activation energies are found to be linear for molar conductivity and largest for the cation and anion self-diffusion coefficients. The activation energies for the self-diffusion of CHCl3 appear to be identical with those obtained from fluidity data. PMID:27557153

  10. A novel metabolite (1,3-benzenediol, 5-hexyl) production by Exophiala spinifera strain FM through dibenzothiophene desulfurization.

    PubMed

    Elmi, Fatemeh; Etemadifar, Zahra; Emtiazi, Giti

    2015-05-01

    Sulfur dioxide which is released from petroleum oil combustion causes pollution over the atmosphere and the soil. Biodesulfurization can be used as a complementary method of hydrodesulfurization, the common method of petroleum desulfurization in refineries. Many studies have been carried out to develop biological desulfurization of dibenzothiophene (DBT) with bacterial biocatalysts. However, fungi are capable to metabolize a wide range of aromatic hydrocarbons through cytochrome P450 and their extracellular enzymes. The aim of the present work was isolation and identification of fungi biocatalysts capable for DBT utilization as sulfur source and production of novel metabolites. DBT consumption and the related produced metabolites were analyzed by HPLC and GC-MS respectively. One of the isolated fungi that could utilize DBT as sole sulfur source was identified by both traditional and molecular experiments and registered in NCBI as Exophiala spinifera FM strain (accession no. KC952672). This strain could desulfurize 99 % of DBT (0.3 mM) as sulfur source by co-metabolism reaction with other carbon sources through the same pathway as 4S and produced 2-hydroxy biphenyl (2-HBP) during 7 days of incubation at 30 °C and 180 rpm shaking. However, the isolate was able to transform 2-HBP to 1,3-benzenediol, 5-hexyl. While biphenyl compounds are toxic to leaving cells, biotransformation of them can reduce their toxicity and the fungi will be more tolerant to the final product. These data are the first report about the desulfurization of DBT comparable to 4S-pathway and production of innovative metabolite by E. spinifera FM strain. PMID:25752234

  11. A novel metabolite (1,3-benzenediol, 5-hexyl) production by Exophiala spinifera strain FM through dibenzothiophene desulfurization.

    PubMed

    Elmi, Fatemeh; Etemadifar, Zahra; Emtiazi, Giti

    2015-05-01

    Sulfur dioxide which is released from petroleum oil combustion causes pollution over the atmosphere and the soil. Biodesulfurization can be used as a complementary method of hydrodesulfurization, the common method of petroleum desulfurization in refineries. Many studies have been carried out to develop biological desulfurization of dibenzothiophene (DBT) with bacterial biocatalysts. However, fungi are capable to metabolize a wide range of aromatic hydrocarbons through cytochrome P450 and their extracellular enzymes. The aim of the present work was isolation and identification of fungi biocatalysts capable for DBT utilization as sulfur source and production of novel metabolites. DBT consumption and the related produced metabolites were analyzed by HPLC and GC-MS respectively. One of the isolated fungi that could utilize DBT as sole sulfur source was identified by both traditional and molecular experiments and registered in NCBI as Exophiala spinifera FM strain (accession no. KC952672). This strain could desulfurize 99 % of DBT (0.3 mM) as sulfur source by co-metabolism reaction with other carbon sources through the same pathway as 4S and produced 2-hydroxy biphenyl (2-HBP) during 7 days of incubation at 30 °C and 180 rpm shaking. However, the isolate was able to transform 2-HBP to 1,3-benzenediol, 5-hexyl. While biphenyl compounds are toxic to leaving cells, biotransformation of them can reduce their toxicity and the fungi will be more tolerant to the final product. These data are the first report about the desulfurization of DBT comparable to 4S-pathway and production of innovative metabolite by E. spinifera FM strain.

  12. Stabilizing effects of estertins mercaptide (methyl acrylate) for PVC degradation

    NASA Astrophysics Data System (ADS)

    Zhang, S. H.; Liu, T. M.; Li, J. L.; Wang, C. R.; Li, C.; Wang, Z. Q.

    2016-07-01

    The thermal and UV light (ultraviolet light) stability of PVC films with estertins mercaptide (methyl acrylate), methyltins mercaptide and the compound consisted of estertins mercaptide (methyl acrylate) and hydrotalcite (2:2.5) were investigated by ageing in a circulation oven at 190 °C and irradiating with 72W UV light for 96h, respectively, and then the yellowness and transmission rate were tested by Color Quest XE. Hydrotalcite was proved to have good synergies with estertins mercaptide (methyl acrylate) on improving the thermal stability and UV light stability. The retarding effects of the heat stabilizers to PVC degradation were tested by TGA from 50°C to 600°C. The results show that temperature of HCl evolution from PVC film was improved obviously by compounding with estertins mercaptide(methyl acrylate) and hydrotalcite and estertins mercaptide(methyl acrylate) was found to have a better long term stability. Sn4+ consistence of water and seawater in which films before and after UV light irradiation were soaked for 60 days was analyzed by ICP; the results indicate that the Sn4+ consistence from the films with estertins mercaptide(methyl acrylate) as thermal stabilizer was lower than that from the film with methyltins mercaptide. The crosslink moderately by UV irradiation for PVC films can hold back the dissolution of organotin heat stabilizers from PVC products into water and seawater.

  13. Industrially relevant epoxy-acrylate hybrid resin photopolymerizations

    NASA Astrophysics Data System (ADS)

    Ajiboye, Gbenga I.

    Photopolymerization of epoxy-acrylate hybrid resins takes advantages of inherent properties present in the free-radical and cationic reactions to reduce oxygen inhibition problems that plague free-radical reactions. Similarly, the combined reaction mechanisms reduce moisture sensitivity of the cationic reactions. Despite the advantages of epoxy-acrylate hybrid resins, problems persist that need to be addressed. For example, low conversion and polymerization rate of the epoxides are a problem, because the fast acrylate conversion prevents the epoxide from reaching high conversion. Controlling phase separation is challenging, since two moieties with different properties are reacting. The physical properties of the polymer will be impacted by the availability of different moieties. High shrinkage stress results from the acrylate moiety, causing buckling and cracking in film and coating applications. The overall goal of this study is to use the fundamental knowledge of epoxy-acrylate hybrid resins to formulate industrially viable polymers. In order to achieve this goal, the study focuses on the following objectives: (I) determine the apparent activation energy of the hybrid monomer METHB, (II) increase epoxide conversion and polymerization rate of hybrid formulations, and (III) control physical properties in epoxy-acrylate hybrid resins. In order to increase the epoxide conversion and rate of polymerization, the sensitivity of epoxides to alcohol is used to facilitate the activated monomer (AM) mechanism and induce a covalent bond between the epoxide and acrylate polymers through the hydroxyl group. It is hypothesized that if the AM mechanism is facilitated, epoxide conversion will increase. As a result, the resins can be tailored to control phase separation and physical properties, and shrinkage stress can be reduced. In pursuit of these objectives, the hybrid monomer METHB was polymerized at temperatures ranging from 30°C to 70°C to obtain apparent activation

  14. Advances in acrylic-alkyd hybrid synthesis and characterization

    NASA Astrophysics Data System (ADS)

    Dziczkowski, Jamie

    2008-10-01

    In situ graft acrylic-alkyd hybrid resins were formed by polymerizing acrylic and acrylic-mixed monomers in the presence of alkyds by introduction of a free radical initiator to promote graft formation. Two-dimensional NMR, specifically gradient heteronuclear multiple quantum coherence (gHMQC), was used to clarify specific graft sites of the hybrid materials. Both individual and mixed-monomer systems were produced to determine any individual monomer preferences and to model current acrylic-alkyd systems. Different classes of initiators were used to determine any initiator effects on graft location. The 2D-NMR results confirm grafting at doubly allylic hydrogens located on the fatty acid chains and the polyol segment of the alkyd backbone. The gHMQC spectra show no evidence of grafting across double bonds on either pendant fatty acid groups or THPA unsaturation sites for any of the monomer or mixed monomer systems. It was also determined that choice of initiator has no effect on graft location. In addition, a design of experiments using response surface methodology was utilized to obtain a better understanding of this commercially available class of materials and relate both the chemical and physical properties to one another. A Box-Behnkin design was used, varying the oil length of the alkyd phase, the degree of unsaturation in the polyester backbone, and acrylic to alkyd ratio. Acrylic-alkyd hybrid resins were reduced with an amine/water mixture. Hydrolytic stability was tested and viscoelastic properties were obtained to determine crosslink density. Cured films were prepared and basic coatings properties were evaluated. It was found that the oil length of the alkyd is the most dominant factor for final coatings properties of the resins. Acrylic to alkyd ratio mainly influences the resin properties such as acid number, average molecular weight, and hydrolytic stability. The degree of unsaturation in the alkyd backbone has minimal effects on resin and film

  15. Analysis of emulsion stability in acrylic dispersions

    NASA Astrophysics Data System (ADS)

    Ahuja, Suresh

    2012-02-01

    Emulsions either micro or nano permit transport or solubilization of hydrophobic substances within a water-based phase. Different methods have been introduced at laboratory and industrial scales: mechanical stirring, high-pressure homogenization, or ultrasonics. In digital imaging, toners may be formed by aggregating a colorant with a latex polymer formed by batch or semi-continuous emulsion polymerization. Latex emulsions are prepared by making a monomer emulsion with monomer like Beta-carboxy ethyl acrylate (β-CEA) and stirring at high speed with an anionic surfactant like branched sodium dodecyl benzene sulfonates , aqueous solution until an emulsion is formed. Initiator for emulsion polymerization is 2-2'- azobis isobutyramide dehydrate with chain transfer agent are used to make the latex. If the latex emulsion is unstable, the resulting latexes produce a toner with larger particle size, broader particle size distribution with relatively higher latex sedimentation, and broader molecular weight distribution. Oswald ripening and coalescence cause droplet size to increase and can result in destabilization of emulsions. Shear thinning and elasticity of emulsions are applied to determine emulsion stability.

  16. Fracture properties of an acrylic bone cement.

    PubMed

    Bialoblocka-Juszczyk, E; Baleani, M; Cristofolini, L; Viceconti, M

    2008-01-01

    This study investigated experimentally the fracture properties, i.e., the fatigue strength, the resistance to crack propagation and the fracture toughness, of an acrylic bone cement (Cemex RX). The mean endurance limit was determined following the staircase method. The endurance limit was estimated at 9.2 MPa. The fatigue crack propagation rate was measured according to the ASTM E647 standard. The equation of the line fitting the crack growth per cycle (da/dN) versus the stress-intensity factor range (delta K), in a log-log graph, was used to calculate the empirical constants of Paris' law for the selected bone cement: da/dN (m/cycle) = 3.56 x 10(-7) x delta K (MPa x m1/2)5.79. This power-law relationship described well (R2 = 0.96) the growth rate in the stable crack growth region, i.e., in the mid delta K range. The fracture toughness K(IC) of the bone cement was determined according to the ASTM E399 standard. The K(IC) mean value was 1.38 MPa x m1/2. These experimental results provide the set of necessary inputs for numerical studies aimed to investigate the damage accumulation process in the mantle fixing cemented prostheses.

  17. Effect of curing cycle on the tensile strength of the bond between heat cured denture base acrylic resin and acrylic resin denture teeth.

    PubMed

    Dalal, Ayesha; Juszczyk, Andrzej S; Radford, David R; Clark, Robert K F

    2009-12-01

    The effect of different curing cycles on the tensile strength of the bond between one brand of cross-linked acrylic resin teeth and three heat cured denture base acrylic resins was tested. There were differences in the tensile bond strength between the three heat cured denture base acrylic resins and the three curing cycles used. The bond strength of the acrylic resin denture base material made by the same manufacturer as the cross-linked acrylic resin denture teeth was higher. The bond strength following the short cycle was lowest in all cases, individual differences between curing cycles failed to reach statistical significance. PMID:20158054

  18. Crystal structure of 1,3-di­cyclo­hexyl-1-[3-(pyren-1-yl)prop­anoyl]urea

    PubMed Central

    González-Juárez, Edgar; Güizado-Rodríguez, Marisol; Barba, Victor; Tlahuext, Hugo

    2015-01-01

    In the title compound, C33H38N2O2, each of the cyclo­hexyl rings adopts a chair conformation. The two planes involving carbonyl groups, C—(C=O)—N and N—(C=O)—N, are oriented at a dihedral angle of 62.28 (10)°. In the crystal, two neighboring mol­ecules are linked by a pair of N—H⋯O inter­actions, generating an inversion dimer. The dimers are inter­connected by C—H⋯O hydrogen bonds into a supra­molecular chain along the a-axis direction. PMID:26594450

  19. Universal charge quenching and stability of proteins in 1-methyl-3-alkyl (hexyl/octyl) imidazolium chloride ionic liquid solutions.

    PubMed

    Rawat, Kamla; Bohidar, H B

    2012-09-13

    This study reports pH dependent stability of protein dispersions of five common proteins, bovine serum albumin (BSA), human serum albumin (HSA), immunoglobulin (IgG), β-lactoglobulin (β-Lg), and gelatin-B (Gel-B), all having isoelectric pH, pI ≈ 5, in room temperature ionic liquid solutions of 1-methyl-3-alkyl (hexyl/octyl) imidazolium chloride (concentration 0-0.2% w/v). Molecular hydrophobicity index, (H-index = hydrophobicity/hydrophilicity) of these molecules spanned the range 0.43-0.87. Electrophoretic characteristics, surface tension data and hydrodynamic size information revealed that IL solutions provide dispersion stability owing to specific protein-IL binding which did not alter their pI values though their surface charge was considerably screened. Change in maximum (ζ(max)) and minimum (ζ(min)) zeta potential values observed at pH ~3 (maximum protonated state) and pH ~8 (maximum deprotonated state) could be described universally as function of IL concentration, c as Δζ(x) = [1 - exp(-ac)] where Δζ(x) is either |(ζ(max) - ζ(w))|/ζ(w) or |(ζ(min) - ζ(w))|/ζ(w), and ζ(w) is the corresponding value in water. Tensiometry data showed two major stages of protein-IL interactions: (i) for c < cmc of IL, the IL molecules selectively bind with imidazolium cation through electrostatic forces forming protein-IL (complex) and (ii) for c> cmc free IL-aggregates begin to form. Similarly, we can define Δγ(x) as either |(γ(max) - γ(w))|/γ(w) at pH 3 or |(γ(min) - γ(w))|/γ(w) at pH 8. Both Δζ(x) and Δγ(x) showed linear dependence with c, Δγ(min, max) (or Δζ(min, max)) = (1 - K(γ) (or K(ζ)) H-index), where the slopes K(ζ) and K(γ) defined intermolecular interactions. Hydrodynamic radii data revealed protein stabilization, circular dichroism spectra implied retention of secondary structures, and Raman spectra confirmed a marginal increase in water structure. Results concluded that selective binding of IL molecules to protein surface in

  20. Universal charge quenching and stability of proteins in 1-methyl-3-alkyl (hexyl/octyl) imidazolium chloride ionic liquid solutions.

    PubMed

    Rawat, Kamla; Bohidar, H B

    2012-09-13

    This study reports pH dependent stability of protein dispersions of five common proteins, bovine serum albumin (BSA), human serum albumin (HSA), immunoglobulin (IgG), β-lactoglobulin (β-Lg), and gelatin-B (Gel-B), all having isoelectric pH, pI ≈ 5, in room temperature ionic liquid solutions of 1-methyl-3-alkyl (hexyl/octyl) imidazolium chloride (concentration 0-0.2% w/v). Molecular hydrophobicity index, (H-index = hydrophobicity/hydrophilicity) of these molecules spanned the range 0.43-0.87. Electrophoretic characteristics, surface tension data and hydrodynamic size information revealed that IL solutions provide dispersion stability owing to specific protein-IL binding which did not alter their pI values though their surface charge was considerably screened. Change in maximum (ζ(max)) and minimum (ζ(min)) zeta potential values observed at pH ~3 (maximum protonated state) and pH ~8 (maximum deprotonated state) could be described universally as function of IL concentration, c as Δζ(x) = [1 - exp(-ac)] where Δζ(x) is either |(ζ(max) - ζ(w))|/ζ(w) or |(ζ(min) - ζ(w))|/ζ(w), and ζ(w) is the corresponding value in water. Tensiometry data showed two major stages of protein-IL interactions: (i) for c < cmc of IL, the IL molecules selectively bind with imidazolium cation through electrostatic forces forming protein-IL (complex) and (ii) for c> cmc free IL-aggregates begin to form. Similarly, we can define Δγ(x) as either |(γ(max) - γ(w))|/γ(w) at pH 3 or |(γ(min) - γ(w))|/γ(w) at pH 8. Both Δζ(x) and Δγ(x) showed linear dependence with c, Δγ(min, max) (or Δζ(min, max)) = (1 - K(γ) (or K(ζ)) H-index), where the slopes K(ζ) and K(γ) defined intermolecular interactions. Hydrodynamic radii data revealed protein stabilization, circular dichroism spectra implied retention of secondary structures, and Raman spectra confirmed a marginal increase in water structure. Results concluded that selective binding of IL molecules to protein surface in

  1. Methyl tertiary hexyl ether and methyl tertiary octyl ether as gasoline oxygenates: assessing risks from atmospheric dispersion and deposition.

    PubMed

    Snelling, Jeff; Barnett, Mark O; Zhao, Dongye; Arey, J Samuel

    2006-10-01

    Methyl tertiary hexyl ether (MtHxE) and methyl tertiary octyl ether (MtOcE) are currently being developed as replacement oxygenates for methyl tertiary butyl ether (MtBE) in gasoline. As was the case with MtBE, the introduction of these ethers into fuel supplies guarantees their introduction into the environment as well. In this study, a screening-level risk assessment was performed by comparing predicted environmental concentrations (PEC) of these ethers to concentrations that might cause adverse effects to humans or ecosystems. A simple box model that has successfully estimated urban air concentrations of MtBE was adapted to predict atmospheric concentrations of MtHxE and MtOcE. Expected atmospheric concentrations of these ethers were also estimated using the European Union System for the Evaluation of Substances (EUSES) multimedia fate model, which simultaneously calculates PECs in the various environmental compartments of air, water, soil, and sediment. Because little or no data are available on the physicochemical, environmental, and toxicological properties of MtHxE and MtOcE, estimation methods were used in conjunction with EUSES to predict both the PECs and the concentrations at which these ethers might pose a threat. The results suggest that these ethers would contaminate the air of a moderately sized U.S. city (Boston, MA) at levels similar to those found previously for MtBE. The risk assessment module in EUSES predicted risk characterization ratios of 10(-3) and 10(-2) for MtHxE and MtOcE, respectively, in Boston, and 10(-2) and 10(-1) in very large urban centers, suggesting that these ethers pose only a minimal threat to ecosystems at the anticipated environmental concentrations. The assessment also indicates that these compounds are possible human carcinogens and that they may be present in urban air at concentrations that pose an unacceptable cancer risk. Therefore, testing of the toxicological properties of these compounds is recommended before they

  2. Acrylic Resin Cytotoxicity for Denture Base--Literature Review.

    PubMed

    Goiato, Marcelo C; Freitas, Emily; dos Santos, Daniela; de Medeiros, Rodrigo; Sonego, Mariana

    2015-01-01

    Acrylic resin is a widely used material in clinical practice, and a satisfactory biocompatibility is essential. When the resin polymerization reaction is incomplete, residual monomers are released into the oral cavity. The aim of this study was to evaluate, through a literature review, the cytotoxicity caused by the denture base acrylic resin used, and its components. The selection of published studies was performed on the Pubmed database from January 2008 to July 2013. The keywords used were: "cytotoxicity and acrylic resins", "cytotoxicity and denture base resins" and "cytotoxicity and oral prosthesis". Inclusion criteria were: in vitro studies and literature reviews published in English that evaluated the acrylic resin cytotoxicity for denture base and its components. Studies with no reference to the search strategy were excluded. A total of 182 articles were found. Among these, only 13 were included for writing this review. The MTT test is the most common test used to evaluate acrylic resin cytotoxicity. Auto-polymerized resin is more cytotoxic than heat-polymerized resin because of its higher quantity of residual monomers which cause cell and tissue changes in the oral mucosa. However, more studies are necessary for the development of biocompatible materials.

  3. Impact Delamination and Fracture in Aluminum/Acrylic Sandwich Plates

    NASA Technical Reports Server (NTRS)

    Liaw, Benjamin; Zeichner, Glenn; Liu, Yanxiong; Bowles, Kenneth J. (Technical Monitor)

    2000-01-01

    Impact-induced delamination and fracture in 6061-T6 aluminum/cast acrylic sandwich plates adhered by epoxy were generated in an instrumented drop-weight impact machine. Although only a small dent was produced on the aluminum side when a hemispherical penetrator tup was dropped onto it from a couple of inches, a large ring of delamination at the interface was observed. The delamination damage was often accompanied by severe shattering in the acrylic substratum. Damage patterns in the acrylic layer include radial and ring cracks and, together with delamination at the interface, may cause peeling-off of acrylic material from the sandwich plate. Theory of stress-wave propagation can be used to explain these damage patterns. The impact tests were conducted at various temperatures. The results also show clearly that temperature effect is very important in impact damage. For pure cast acrylic nil-ductile transition (NDT) occurs between 185-195 F. Excessive impact energy was dissipated into fracture energy when tested at temperature below this range or through plastic deformation when tested at temperature above the NDT temperature. Results from this study will be used as baseline data for studying fiber-metal laminates, such as GLARE and ARALL for advanced aeronautical and astronautical applications.

  4. 1-3-A Resolution Structure of Human Glutathione S-Transferase With S-Hexyl Glutathione Bound Reveals Possible Extended Ligandin Binding Site

    SciTech Connect

    Trong, I.Le; Stenkamp, R.E.; Ibarra, C.; Atkins, W.M.; Adman, E.T.

    2005-08-22

    Cytosolic glutathione S-transferases (GSTs) play a critical role in xenobiotic binding and metabolism, as well as in modulation of oxidative stress. Here, the high-resolution X-ray crystal structures of homodimeric human GSTA1-1 in the apo form and in complex with S-hexyl glutathione (two data sets) are reported at 1.8, 1.5, and 1.3A respectively. At this level of resolution, distinct conformations of the alkyl chain of S-hexyl glutathione are observed, reflecting the nonspecific nature of the hydrophobic substrate binding site (H-site). Also, an extensive network of ordered water, including 75 discrete solvent molecules, traverses the open subunit-subunit interface and connects the glutathione binding sites in each subunit. In the highest-resolution structure, three glycerol moieties lie within this network and directly connect the amino termini of the glutathione molecules. A search for ligand binding sites with the docking program Molecular Operating Environment identified the ordered water network binding site, lined mainly with hydrophobic residues, suggesting an extended ligand binding surface for nonsubstrate ligands, the so-called ligandin site. Finally, detailed comparison of the structures reported here with previously published X-ray structures reveal a possible reaction coordinate for ligand-dependent conformational changes in the active site and the C-terminus.

  5. [Chiral separation of five beta-blockers using di-n-hexyl L-tartrate-boric acid complex as mobile phase additive by reversed-phase liquid chromatography].

    PubMed

    Yang, Juan; Wang, Lijuan; Guo, Qiaoling; Yang, Gengliang

    2012-03-01

    A reversed-phase high performance liquid chromatographic (HPLC) method using the di-n-hexyl L-tartrate-boric acid complex as a chiral mobile phase additive was developed for the enantioseparation of five beta-blockers including propranolol, esmolol, metoprolol, bisoprolol and sotalol. In order to obtain a better enantioseparation, the influences of concentrations of di-n-butyl L-tartrate and boric acid, the type, concentration and pH of the buffer, methanol content as well as the molecular structure of analytes were extensively investigated. The separation of the analytes was performed on a Venusil MP-C18 column (250 mm x 4.6 mm, 5 microm). The mobile phase was 15 mmol/L ammonium acetate-methanol containing 60 mmol/L boric acid, 70 mmol/L di-n-hexyl L-tartrate (pH 6.00). The volume ratios of 15 mmol/L ammonium acetate to methanol were 20: 80 for propranolol, esmolol, metoprolol, bisoprolol and 30: 70 for sotalol. The flow rate was 0.5 mL/min and the detection wavelength was set at 214 nm. Under the optimized conditions, baseline enantioseparation was obtained separately for the five pairs of analytes.

  6. Langmuir structure of poly (2-vinylpyridine-b-hexyl isocyanate) rod-coil diblock copolymers at the air/water Interface

    NASA Astrophysics Data System (ADS)

    Ahmad, Farhan

    2005-03-01

    We conducted a systematic interfacial study for the complete range (5%-90% of rod mole percentage) of an amphiphilic rod-coil system, poly (hexyl isocyanate)-b-(2-vinylpyridine) at the air/water and air/solid interface. We applied Langmuir balance technique, scanning probe microscopy (SPM), transmission electron microscopy (TEM) and X-ray reflectivity for the complete characterization of the monolayer at the interfaces. The phase isotherms showed the well amphiphilic balance for the diblock copolymers, and the formation of stable monolayers. With the increasing rod content, the consistent increase in the monolayer packing density was observed by the phase isotherms and supported by X-ray reflectivity. SPM and TEM characterization showed their interesting surface morphology according to the varying rod mole percentage in the rod-coil system. Rod mole percentage 5%-15% showed micellar morphology. Rod mole percentage 23%-32% showed distinct and dispersed rods, whereas rod mole percentage 70%-90% showed well packed structure similar to lamella phase. We found the tendency of the diblock system to adopt a packed monomolecular structure has increased by the increasing rod content. This lead us to conclude that it is the hexyl-isocyanate (rod part) that governs mostly the interfacial behavior of rod-coil block copolymers.

  7. Biosynthetic pathway for acrylic acid from glycerol in recombinant Escherichia coli.

    PubMed

    Tong, Wenhua; Xu, Ying; Xian, Mo; Niu, Wei; Guo, Jiantao; Liu, Huizhou; Zhao, Guang

    2016-06-01

    Acrylic acid is an important industrial feedstock. In this study, a de novo acrylate biosynthetic pathway from inexpensive carbon source glycerol was constructed in Escherichia coli. The acrylic acid was produced from glycerol via 3-hydroxypropionaldehyde, 3-hydroxypropionyl-CoA, and acrylyl-CoA. The acrylate production was improved by screening and site-directed mutagenesis of key enzyme enoyl-CoA hydratase and chromosomal integration of some exogenous genes. Finally, our recombinant strain produced 37.7 mg/L acrylic acid under shaking flask conditions. Although the acrylate production is low, our study shows feasibility of engineering an acrylate biosynthetic pathway from inexpensive carbon source. Furthermore, the reasons for limited acrylate production and further strain optimization that should be performed in the future were also discussed. PMID:26782744

  8. Nucleophilic addition of reactive dyes on amidoximated acrylic fabrics.

    PubMed

    El-Shishtawy, Reda M; El-Zawahry, Manal M; Abdelghaffar, Fatma; Ahmed, Nahed S E

    2014-01-01

    Seven reactive dyes judiciously selected based on chemical structures and fixation mechanisms were applied at 2% of of shade on amidoximated acrylic fabrics. Amidoximated acrylic fabric has been obtained by a viable amidoximation process. The dyeability of these fabrics was evaluated with respect to the dye exhaustion, fixation, and colour strength under different conditions of temperature and dyeing time. Nucleophilic addition type reactive dyes show higher colour data compared to nucleophilic substitution ones. FTIR studies further implicate the binding of reactive dyes on these fabrics. A tentative mechanism is proposed to rationalize the high fixation yield obtained using nucleophilic addition type reactive dyes. Also, the levelling and fastness properties were evaluated for all dyes used. Excellent to good fastness and levelling properties were obtained for all samples irrespective of the dye used. The result of investigation offers a new method for a viable reactive dyeing of amidoximated acrylic fabrics.

  9. Properties of the modified cellulosic fabrics using polyurethane acrylate copolymers.

    PubMed

    Tabasum, Shazia; Zuber, Mohammad; Jabbar, Abdul; Zia, Khalid Mahmood

    2013-05-15

    Polyurethane acrylate copolymers (PAC) were synthesized via emulsion polymerization following three step synthesis process using toluene-2,4-diisocyanate, hydroxy terminated poly(caprolactone) diol, 2-hydroxyethylacrylate (HEA) and butyl acrylate (BuA). Structural characteristics of the synthesized polyurethane acrylate copolymer (PAC) were studied using Fourier Transform Infrared (FT-IR) spectrophotometer and are with accordance with the proposed PAC structure. The physicochemical properties such as solid contents (%), tackiness, film appearance and emulsion stability were studied, discussed and co-related with other findings. The plain weave poly-cotton printed fabrics after application of PAC was evaluated applying colorfastness standard test method. The results revealed that emulsion stability is the main controlling factor of the synthesized material in order to get better applications and properties. The emulsion stability of the synthesized material increased with increase in molecular weight of the polycaprolactone diol. PMID:23544644

  10. Properties of the modified cellulosic fabrics using polyurethane acrylate copolymers.

    PubMed

    Tabasum, Shazia; Zuber, Mohammad; Jabbar, Abdul; Zia, Khalid Mahmood

    2013-05-15

    Polyurethane acrylate copolymers (PAC) were synthesized via emulsion polymerization following three step synthesis process using toluene-2,4-diisocyanate, hydroxy terminated poly(caprolactone) diol, 2-hydroxyethylacrylate (HEA) and butyl acrylate (BuA). Structural characteristics of the synthesized polyurethane acrylate copolymer (PAC) were studied using Fourier Transform Infrared (FT-IR) spectrophotometer and are with accordance with the proposed PAC structure. The physicochemical properties such as solid contents (%), tackiness, film appearance and emulsion stability were studied, discussed and co-related with other findings. The plain weave poly-cotton printed fabrics after application of PAC was evaluated applying colorfastness standard test method. The results revealed that emulsion stability is the main controlling factor of the synthesized material in order to get better applications and properties. The emulsion stability of the synthesized material increased with increase in molecular weight of the polycaprolactone diol.

  11. Biocatalytic functionalization of hydroxyalkyl acrylates and phenoxyethanol via phosphorylation.

    PubMed

    Tasnádi, Gábor; Hall, Mélanie; Baldenius, Kai; Ditrich, Klaus; Faber, Kurt

    2016-09-10

    The enzymatic phosphorylation of phenoxyethanol, 2-hydroxyethyl acrylate and 4-hydroxybutyl acrylate catalyzed by acid phosphatases PhoN-Sf and PiACP at the expense of inorganic di-, tri-, hexameta- or polyphosphate was applied to the preparative-scale synthesis of phosphorylated compounds. The reaction conditions were optimized with respect to enzyme immobilization, substrate concentration, pH and type of phosphate donor. The mild reaction conditions prevented undesired polymerization and hydrolysis of the acrylate ester moiety. Application of a continuous flow system allowed facile scale-up and mono-phosphates were obtained in up to 26% isolated yield with space-time yields of 0.89kgL(-1)h(-1). PMID:27422352

  12. Biocatalytic functionalization of hydroxyalkyl acrylates and phenoxyethanol via phosphorylation.

    PubMed

    Tasnádi, Gábor; Hall, Mélanie; Baldenius, Kai; Ditrich, Klaus; Faber, Kurt

    2016-09-10

    The enzymatic phosphorylation of phenoxyethanol, 2-hydroxyethyl acrylate and 4-hydroxybutyl acrylate catalyzed by acid phosphatases PhoN-Sf and PiACP at the expense of inorganic di-, tri-, hexameta- or polyphosphate was applied to the preparative-scale synthesis of phosphorylated compounds. The reaction conditions were optimized with respect to enzyme immobilization, substrate concentration, pH and type of phosphate donor. The mild reaction conditions prevented undesired polymerization and hydrolysis of the acrylate ester moiety. Application of a continuous flow system allowed facile scale-up and mono-phosphates were obtained in up to 26% isolated yield with space-time yields of 0.89kgL(-1)h(-1).

  13. Colour Stability of Heat and Cold Cure Acrylic Resins

    PubMed Central

    Ganesh, P R; Reddy, Madan Mohan; Ebenezar, A.V. Rajesh; Sivakumar, G

    2015-01-01

    Introduction: To evaluate the colour stability of heat and cold cure acrylic resins under simulated oral conditions with different colorants. Materials and Methods: Three different brands of heat cure acrylic resin and two rapid cure auto polymerizing acrylic resin of commercial products such as Trevelon Heat Cure (THC), DPI Heat cure (DHC), Pyrax Heat Cure (PHC), DPI Cold cure (DCC) and Acralyn-R-Cold cure (ACC) have been evaluated for discoloration and colour variation on subjecting it to three different, commonly employed food colorants such as Erythrosine, Tartarizine and Sunset yellow. In order to simulate the oral condition the food colorants were diluted with artificial saliva to the samples taken up for the study. These were further kept in an incubator at 37°C ± 1°C. The UV-visible spectrophotometer has been utilized to evaluate the study on the basis of CIE L* a* b* system. The prepared samples for standard evaluation have been grouped as control group, which has been tested with a white as standard, which is applicable for testing the colour variants. Results: The least colour changes was found to be with Sunset Yellow showing AE* value of 3.55 with heat cure acrylic resin branded as PHC material and the highest colour absorption with Tartarizine showing AE* value of 12.43 in rapid cure autopolymerzing acrylic resin material branded as ACC material. Conclusion: ACC which is a self cure acrylic resin shows a higher colour variation to the tartarizine food coloration. There were not much of discoloration values shown on the denture base resins as the food colorants are of organic azodyes. PMID:25738078

  14. Technology and the use of acrylics for provisional dentine protection.

    PubMed

    Kapusevska, Biljana; Dereban, Nikola; Popovska, Mirjana; Nikolovska, Julijana; Radojkova Nikolovska, Vеrа; Zabokova Bilbilova, Efka; Mijoska, Aneta

    2013-01-01

    Acrylics are compounds polymerized from monomers of acrylic, metacrylic acid or acrylonitrates. The purpose of this paper is to present the technology and use of acrylics for provisional dentine protection in the practice of dental prosthodontics. For this reason, we followed 120 clinical cases from the everyday clinical practice, divided into 4 groups of 30 patients who needed prosthetic reconstruction. The first group included cases in which we applied celluloid crowns for dentine protection, for the second group we used acrylic teeth from a set of teeth for complete dentures; in the third and fourth groups the fabrication was done with the system of an impression matrix and the acrylic resin block technique respectively. In all the examined patients, the gingival index by Silness and Loe and the vitality of the dental pulp were verified clinically, after preparation and 8 days from the placement of the provisional crown. The value for dental sensitivity measured after preparation was 2.59, and 8 days after the placement of the provisional crown it bwas 3.1. From these results we can conclude that after the 8th day from the placement of the provisional crown, there was an adaptation period, characterized by a decrease in the painful sensations. The value of the Silness and Loe gingival index measured after the preparation was 1.34, and 8 days from the placement of the provisional crown was 0.94. The results inclined us to the fact that the provisional acrylic crowns facilitated the reparation of the periodontal tissue. PMID:24566021

  15. The creep behavior of acrylic denture base resins.

    PubMed

    Sadiku, E R; Biotidara, F O

    1996-01-01

    The creep behavior of acrylic dental base resins, at room temperature and at different loading conditions, has been examined. The behaviors of these resins are similar to that of "commercial perspex" at room temperature over a period of 1000 seconds. The pseudo-elastic moduli of the blends of PMMA VC show a significant increase compared with PMMA alone. The addition of the PVC powder to the heat-cured acrylic resin increased the time-dependent elastic modulus. This increase in elastic modulus is advantageous in the production of denture based resins of improv mechanical properties.

  16. Kinetic relationships governing addition of methanol to methyl acrylate

    SciTech Connect

    Chubarov, G.A.; Danov, S.M.; Kutnyaya, M.Yu.

    1988-11-10

    The kinetic relationships governing the addition of methanol to methyl acrylate and the reverse reaction, i.e., the elimination of methanol from methyl /beta/-methoxypropionate catalyzed by sulfuric and p-toluenesulfonic acids, were investigated. The rate of the forward reaction depends on the concentrations of methyl acrylate, methanol, and the catalyst, and the rate of the reverse reaction depends on the concentration of methyl /beta/-methoxypropionate and of the catalyst. A kinetic expression which describes the process well was obtained.

  17. Corrosion resistant properties of polyaniline acrylic coating on magnesium alloy

    NASA Astrophysics Data System (ADS)

    Sathiyanarayanan, S.; Azim, S. Syed; Venkatachari, G.

    2006-12-01

    The performance of the paint coating based on acrylic-polyaniline on magnesium alloy ZM 21 has been studied by electrochemical impedance spectroscopy in 0.5% NaCl solution. The polyaniline was prepared by chemical oxidative method of aniline with ammonium persulphate in phosphoric acid medium. The phosphate-doped polyaniline was characterized by FTIR and XRD methods. Acrylic paint containing the phosphate-doped polyaniline was prepared and coated on magnesium ZM 21 alloy. The coating was able to protect the magnesium alloy and no base metal dissolution was noted even after 75 days exposure to sodium chloride solution.

  18. Cardiovascular effects of acrylic bone cement in rabbits and cats.

    PubMed

    Pelling, D; Butterworth, K R

    1973-06-16

    The cardiovascular responses to forcing acrylic bone cement, Plasticine, or soft paraffin wax into the medullary cavity of the femur have been studied in rabbits and cats. An acute fall in blood pressure, occurring within a few seconds of insertion, was demonstrated with each substance. In a few of the animals the blood pressure response had a second more protracted component and it is suggested that more than one mechanism is involved. The cardiovascular effects that have been observed in man when acrylic cement is used in prosthetic hip surgery also may be due to more than one mechanism. PMID:4714847

  19. Lipase-catalyzed aza-Michael reaction on acrylate derivatives.

    PubMed

    Steunenberg, Peter; Sijm, Maarten; Zuilhof, Han; Sanders, Johan P M; Scott, Elinor L; Franssen, Maurice C R

    2013-04-19

    A methodology has been developed for an efficient and selective lipase-catalyzed aza-Michael reaction of various amines (primary and secondary) with a series of acrylates and alkylacrylates. Reaction parameters were tuned, and under the optimal conditions it was found that Pseudomonas stutzeri lipase and Chromobacterium viscosum lipase showed the highest selectivity for the aza-Michael addition to substituted alkyl acrylates. For the first time also, some CLEAs were examined that showed a comparable or higher selectivity and yield than the free enzymes and other formulations.

  20. Synthesis and Characterization of bis[(2-ethyl-5-methyl-imidazo-4-yl)methyl]Sulfide and Its Coordination Behavior toward Cu(II) as a Possible Approach of a Copper Site Type I

    PubMed Central

    Barrón-Garcés, Juan D.; Mendoza-Díaz, Guillermo; Vilchez-Aguado, Florina; Bernès, Sylvain

    2009-01-01

    The synthesis and characterization of a novel ligand, bis[(2-ethyl-5-methyl-imidazo-4-yl)methyl]sulfide (bemims), as well as a bemims-containing copper(II) coordination complex are described. In this complex, [Cu(bemims)X2] with X = NO3−, bemims acts as a tridentate ligand and two monodentate nitrate ions complete the coordination sphere. Both imidazole N atoms and the thioether S atom of bemims participate in coordination. The Cu(II) ion is five-coordinated with a slightly distorted square-pyramidal geometry (τ = .09). Electrochemical studies and spectroscopic data for this complex are compared with some blue copper proteins in order to assess its ability to mimic the copper center of type I copper proteins. PMID:19587830

  1. 40 CFR 721.6560 - Acrylic acid, polymer with substituted ethene.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.6560 Acrylic acid, polymer with substituted ethene. (a) Chemical... as acrylic acid, polymer with substituted ethene (PMN P-91-521) is subject to reporting under...

  2. 40 CFR 721.6920 - Butyl acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Butyl acrylate, polymer with... acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted silane. (a... butyl acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted...

  3. 40 CFR 721.10223 - Styrenyl surface treated manganese ferrite with acrylic ester polymer (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... ferrite with acrylic ester polymer (generic). 721.10223 Section 721.10223 Protection of Environment... manganese ferrite with acrylic ester polymer (generic). (a) Chemical substance and significant new uses... manganese ferrite with acrylic ester polymer (PMN P-09-582) is subject to reporting under this section...

  4. 40 CFR 721.6920 - Butyl acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Butyl acrylate, polymer with... acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted silane. (a... butyl acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted...

  5. 40 CFR 721.6920 - Butyl acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Butyl acrylate, polymer with... acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted silane. (a... butyl acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted...

  6. 40 CFR 721.463 - Acrylate of polymer based on isophorone diisocyanate (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Acrylate of polymer based on... New Uses for Specific Chemical Substances § 721.463 Acrylate of polymer based on isophorone... substance identified generically as acrylate of polymer based on isophorone diisocyanate (PMN P-00-0626)...

  7. 40 CFR 721.10032 - Acrylic acid, polymer with substituted acrylamides (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.10032 Acrylic acid, polymer with substituted acrylamides (generic). (a... generically as acrylic acid, polymer with substituted acrylamides (PMN P-02-269) is subject to reporting...

  8. 40 CFR 721.6560 - Acrylic acid, polymer with substituted ethene.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.6560 Acrylic acid, polymer with substituted ethene. (a) Chemical... as acrylic acid, polymer with substituted ethene (PMN P-91-521) is subject to reporting under...

  9. 40 CFR 721.463 - Acrylate of polymer based on isophorone diisocyanate (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Acrylate of polymer based on... New Uses for Specific Chemical Substances § 721.463 Acrylate of polymer based on isophorone... substance identified generically as acrylate of polymer based on isophorone diisocyanate (PMN P-00-0626)...

  10. 40 CFR 721.10032 - Acrylic acid, polymer with substituted acrylamides (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.10032 Acrylic acid, polymer with substituted acrylamides (generic). (a... generically as acrylic acid, polymer with substituted acrylamides (PMN P-02-269) is subject to reporting...

  11. 40 CFR 721.463 - Acrylate of polymer based on isophorone diisocyanate (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Acrylate of polymer based on... New Uses for Specific Chemical Substances § 721.463 Acrylate of polymer based on isophorone... substance identified generically as acrylate of polymer based on isophorone diisocyanate (PMN P-00-0626)...

  12. 40 CFR 721.6560 - Acrylic acid, polymer with substituted ethene.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.6560 Acrylic acid, polymer with substituted ethene. (a) Chemical... as acrylic acid, polymer with substituted ethene (PMN P-91-521) is subject to reporting under...

  13. 40 CFR 721.10032 - Acrylic acid, polymer with substituted acrylamides (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.10032 Acrylic acid, polymer with substituted acrylamides (generic). (a... generically as acrylic acid, polymer with substituted acrylamides (PMN P-02-269) is subject to reporting...

  14. 40 CFR 721.10223 - Styrenyl surface treated manganese ferrite with acrylic ester polymer (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... ferrite with acrylic ester polymer (generic). 721.10223 Section 721.10223 Protection of Environment... manganese ferrite with acrylic ester polymer (generic). (a) Chemical substance and significant new uses... manganese ferrite with acrylic ester polymer (PMN P-09-582) is subject to reporting under this section...

  15. 40 CFR 721.10223 - Styrenyl surface treated manganese ferrite with acrylic ester polymer (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... ferrite with acrylic ester polymer (generic). 721.10223 Section 721.10223 Protection of Environment... manganese ferrite with acrylic ester polymer (generic). (a) Chemical substance and significant new uses... manganese ferrite with acrylic ester polymer (PMN P-09-582) is subject to reporting under this section...

  16. 40 CFR 721.10101 - Copolymer of alkyl acrylate and ethyleneglycol dimethacrylate (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Copolymer of alkyl acrylate and... Significant New Uses for Specific Chemical Substances § 721.10101 Copolymer of alkyl acrylate and...) The chemical substance identified generically as copolymer of alkyl acrylate and...

  17. 40 CFR 721.10101 - Copolymer of alkyl acrylate and ethyleneglycol dimethacrylate (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Copolymer of alkyl acrylate and... Significant New Uses for Specific Chemical Substances § 721.10101 Copolymer of alkyl acrylate and...) The chemical substance identified generically as copolymer of alkyl acrylate and...

  18. 40 CFR 721.10101 - Copolymer of alkyl acrylate and ethyleneglycol dimethacrylate (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Copolymer of alkyl acrylate and... Significant New Uses for Specific Chemical Substances § 721.10101 Copolymer of alkyl acrylate and...) The chemical substance identified generically as copolymer of alkyl acrylate and...

  19. 40 CFR 721.10101 - Copolymer of alkyl acrylate and ethyleneglycol dimethacrylate (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Copolymer of alkyl acrylate and... Significant New Uses for Specific Chemical Substances § 721.10101 Copolymer of alkyl acrylate and...) The chemical substance identified generically as copolymer of alkyl acrylate and...

  20. 21 CFR 177.1340 - Ethylene-methyl acrylate copolymer resins.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ethylene-methyl acrylate copolymer resins. 177.1340... copolymer resins. Ethylene-methyl acrylate copolymer resins may be safely used as articles or components of...) For the purpose of this section, the ethylene-methyl acrylate copolymer resins consist of...

  1. 40 CFR 721.10192 - Amides, coco, N-[3-(dibutylamino)propyl], acrylates.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Amides, coco, N- , acrylates. 721... Substances § 721.10192 Amides, coco, N- , acrylates. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as amides, coco, N- , acrylates (PMN...

  2. 40 CFR 721.10192 - Amides, coco, N-[3-(dibutylamino)propyl], acrylates.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Amides, coco, N- , acrylates. 721... Substances § 721.10192 Amides, coco, N- , acrylates. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as amides, coco, N- , acrylates (PMN...

  3. 21 CFR 177.1340 - Ethylene-methyl acrylate copolymer resins.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Ethylene-methyl acrylate copolymer resins. 177... for Use as Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1340 Ethylene-methyl acrylate copolymer resins. Ethylene-methyl acrylate copolymer resins may be safely used...

  4. 21 CFR 177.1340 - Ethylene-methyl acrylate copolymer resins.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Ethylene-methyl acrylate copolymer resins. 177... for Use as Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1340 Ethylene-methyl acrylate copolymer resins. Ethylene-methyl acrylate copolymer resins may be safely used...

  5. 21 CFR 177.1340 - Ethylene-methyl acrylate copolymer resins.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Ethylene-methyl acrylate copolymer resins. 177... Repeated Use Food Contact Surfaces § 177.1340 Ethylene-methyl acrylate copolymer resins. Ethylene-methyl... section, the ethylene-methyl acrylate copolymer resins consist of basic copolymers produced by...

  6. 40 CFR 721.463 - Acrylate of polymer based on isophorone diisocyanate (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Acrylate of polymer based on... New Uses for Specific Chemical Substances § 721.463 Acrylate of polymer based on isophorone... substance identified generically as acrylate of polymer based on isophorone diisocyanate (PMN P-00-0626)...

  7. 40 CFR 721.463 - Acrylate of polymer based on isophorone diisocyanate (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Acrylate of polymer based on... New Uses for Specific Chemical Substances § 721.463 Acrylate of polymer based on isophorone... substance identified generically as acrylate of polymer based on isophorone diisocyanate (PMN P-00-0626)...

  8. 40 CFR 721.10032 - Acrylic acid, polymer with substituted acrylamides (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.10032 Acrylic acid, polymer with substituted acrylamides (generic). (a... generically as acrylic acid, polymer with substituted acrylamides (PMN P-02-269) is subject to reporting...

  9. 40 CFR 721.6920 - Butyl acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Butyl acrylate, polymer with... acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted silane. (a... butyl acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted...

  10. 40 CFR 721.10223 - Styrenyl surface treated manganese ferrite with acrylic ester polymer (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... ferrite with acrylic ester polymer (generic). 721.10223 Section 721.10223 Protection of Environment... manganese ferrite with acrylic ester polymer (generic). (a) Chemical substance and significant new uses... manganese ferrite with acrylic ester polymer (PMN P-09-582) is subject to reporting under this section...

  11. 40 CFR 721.6560 - Acrylic acid, polymer with substituted ethene.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.6560 Acrylic acid, polymer with substituted ethene. (a) Chemical... as acrylic acid, polymer with substituted ethene (PMN P-91-521) is subject to reporting under...

  12. 40 CFR 721.10032 - Acrylic acid, polymer with substituted acrylamides (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.10032 Acrylic acid, polymer with substituted acrylamides (generic). (a... generically as acrylic acid, polymer with substituted acrylamides (PMN P-02-269) is subject to reporting...

  13. 40 CFR 721.6560 - Acrylic acid, polymer with substituted ethene.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Acrylic acid, polymer with substituted... Specific Chemical Substances § 721.6560 Acrylic acid, polymer with substituted ethene. (a) Chemical... as acrylic acid, polymer with substituted ethene (PMN P-91-521) is subject to reporting under...

  14. 40 CFR 721.6920 - Butyl acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Butyl acrylate, polymer with... acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted silane. (a... butyl acrylate, polymer with substituted methyl styrene, methyl methacrylate, and substituted...

  15. 40 CFR 721.9640 - Salt of an acrylic acid - acrylamide terpolymer (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Salt of an acrylic acid - acrylamide... Specific Chemical Substances § 721.9640 Salt of an acrylic acid - acrylamide terpolymer (generic). (a... generically as salt of an acrylic acid - acrylamide terpolymer (PMN P-99-817) is subject to reporting...

  16. 40 CFR 721.321 - Substituted acrylamides and acrylic acid copolymer (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Substituted acrylamides and acrylic... New Uses for Specific Chemical Substances § 721.321 Substituted acrylamides and acrylic acid copolymer... identified generically as substituted acrylamides and acrylic acid copolymer (PMN P-00-0490) is subject...

  17. 40 CFR 721.321 - Substituted acrylamides and acrylic acid copolymer (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Substituted acrylamides and acrylic... New Uses for Specific Chemical Substances § 721.321 Substituted acrylamides and acrylic acid copolymer... identified generically as substituted acrylamides and acrylic acid copolymer (PMN P-00-0490) is subject...

  18. 40 CFR 721.321 - Substituted acrylamides and acrylic acid copolymer (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Substituted acrylamides and acrylic... New Uses for Specific Chemical Substances § 721.321 Substituted acrylamides and acrylic acid copolymer... identified generically as substituted acrylamides and acrylic acid copolymer (PMN P-00-0490) is subject...

  19. 40 CFR 721.9640 - Salt of an acrylic acid - acrylamide terpolymer (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Salt of an acrylic acid - acrylamide... Specific Chemical Substances § 721.9640 Salt of an acrylic acid - acrylamide terpolymer (generic). (a... generically as salt of an acrylic acid - acrylamide terpolymer (PMN P-99-817) is subject to reporting...

  20. 40 CFR 721.9640 - Salt of an acrylic acid - acrylamide terpolymer (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Salt of an acrylic acid - acrylamide... Specific Chemical Substances § 721.9640 Salt of an acrylic acid - acrylamide terpolymer (generic). (a... generically as salt of an acrylic acid - acrylamide terpolymer (PMN P-99-817) is subject to reporting...

  1. 40 CFR 721.338 - Salt of an acrylate copolymer (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Salt of an acrylate copolymer (generic... Substances § 721.338 Salt of an acrylate copolymer (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substances identified generically as salt of an acrylate...

  2. 40 CFR 721.338 - Salt of an acrylate copolymer (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Salt of an acrylate copolymer (generic... Substances § 721.338 Salt of an acrylate copolymer (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substances identified generically as salt of an acrylate...

  3. 40 CFR 721.338 - Salt of an acrylate copolymer (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Salt of an acrylate copolymer (generic... Substances § 721.338 Salt of an acrylate copolymer (generic). Link to an amendment published at 79 FR 34636... substances identified generically as salt of an acrylate copolymer (PMNs P-00-0333 and P-00-0334) are...

  4. 40 CFR 721.338 - Salt of an acrylate copolymer (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Salt of an acrylate copolymer (generic... Substances § 721.338 Salt of an acrylate copolymer (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substances identified generically as salt of an acrylate...

  5. 40 CFR 721.338 - Salt of an acrylate copolymer (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Salt of an acrylate copolymer (generic... Substances § 721.338 Salt of an acrylate copolymer (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substances identified generically as salt of an acrylate...

  6. 40 CFR 721.321 - Substituted acrylamides and acrylic acid copolymer (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Substituted acrylamides and acrylic... New Uses for Specific Chemical Substances § 721.321 Substituted acrylamides and acrylic acid copolymer... identified generically as substituted acrylamides and acrylic acid copolymer (PMN P-00-0490) is subject...

  7. 40 CFR 721.321 - Substituted acrylamides and acrylic acid copolymer (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Substituted acrylamides and acrylic... New Uses for Specific Chemical Substances § 721.321 Substituted acrylamides and acrylic acid copolymer... identified generically as substituted acrylamides and acrylic acid copolymer (PMN P-00-0490) is subject...

  8. 40 CFR 721.9640 - Salt of an acrylic acid - acrylamide terpolymer (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Salt of an acrylic acid - acrylamide... Specific Chemical Substances § 721.9640 Salt of an acrylic acid - acrylamide terpolymer (generic). (a... generically as salt of an acrylic acid - acrylamide terpolymer (PMN P-99-817) is subject to reporting...

  9. 40 CFR 721.9640 - Salt of an acrylic acid - acrylamide terpolymer (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Salt of an acrylic acid - acrylamide... Specific Chemical Substances § 721.9640 Salt of an acrylic acid - acrylamide terpolymer (generic). (a... generically as salt of an acrylic acid - acrylamide terpolymer (PMN P-99-817) is subject to reporting...

  10. Tensile bond strength between auto-polymerized acrylic resin and acrylic denture teeth treated with MF-MA solution

    PubMed Central

    2016-01-01

    PURPOSE This study evaluated the effect of chemical surface treatment using methyl formate-methyl acetate (MF-MA) solution on the tensile bond strength between acrylic denture teeth and auto-polymerized acrylic resin. MATERIALS AND METHODS Seventy maxillary central incisor acrylic denture teeth for each of three different brands (Yamahachi New Ace; Major Dent; Cosmo HXL) were embedded with incisal edge downwards in auto-polymerized resin in polyethylene pipes and ground with silicone carbide paper on their ridge lap surfaces. The teeth of each brand were divided into seven groups (n=10): no surface treatment (control group), MF-MA solution at a ratio of 25:75 (v/v) for 15 seconds, 30 seconds, 60 seconds, 120 seconds, 180 seconds, and MMA for 180 seconds. Auto-polymerized acrylic resin (Unifast Trad) was applied to the ground surface and polymerized in a pressure cooker. A tensile strength test was performed with a universal testing machine. Statistical analysis of the results was performed using two-way analysis of variance (ANOVA) and post-hoc Dunnett T3 test (α=.05). RESULTS The surface treatment groups had significantly higher mean tensile bond strengths compared with the control group (P<.05) when compared within the same brand. Among the surface treatment groups of each brand, there were no significantly different tensile bond strengths between the MF-MA groups and the MMA 180 second group (P>.05), except for the Yamahachi New Ace MF-MA 180-second group (P<.05). CONCLUSION 15-second MF-MA solution can be an alternative chemical surface treatment for repairing a denture base and rebonding acrylic denture teeth with auto-polymerized acrylic resin, for both conventional and cross-linked teeth. PMID:27555897

  11. Degradation of a Sodium Acrylate Oligomer by an Arthrobacter sp

    PubMed Central

    Hayashi, Takaya; Mukouyama, Masaharu; Sakano, Kouichi; Tani, Yoshiki

    1993-01-01

    Arthrobacter sp. strain NO-18 was first isolated from soil as a bacterium which could degrade the sodium acrylate oligomer and utilize it as the sole source of carbon. When 0.2% (wt/wt) oligomer was added to the culture medium, the acrylate oligomer was found to be degraded by 70 to 80% in 2 weeks, using gel permeation chromatography. To determine the maximum molecular weight for biodegradation, the degradation test was done with the hexamer, heptamer, and octamer, which were separated from the oligomer mixture by fractional gel permeation chromatography. The hexamer and heptamer were consumed to the extents of 58 and 36%, respectively, in 2 weeks, but the octamer was not degraded. Oligomers with three different terminal groups were synthesized to examine the effect of the different terminal groups on biodegradation, but few differences were found. Arthrobacter sp. NO-18 assimilated acrylic acid, propionic acid, glutaric acid, 2-methylglutaric acid, and 1,3,5-pentanetricarboxylic acid. Degradation of the acrylic unit structure by this strain is discussed. PMID:8517751

  12. Bond strength between acrylic resin and maxillofacial silicone

    PubMed Central

    HADDAD, Marcela Filié; GOIATO, Marcelo Coelho; dos SANTOS, Daniela Micheline; CREPALDI, Nádia de Marchi; PESQUEIRA, Aldiéris Alves; BANNWART, Lisiane Cristina

    2012-01-01

    The development of implant dentistry improved the possibilities of rehabilitation with maxillofacial prosthesis. However, clinically it is difficult to bond the silicone to the attachment system. Objectives This study aimed to evaluate the effect of an adhesive system on the bond strength between acrylic resin and facial silicone. Material and Methods A total of 120 samples were fabricated with auto-polymerized acrylic resin and MDX 4-4210 facial silicone. Both materials were bonded through mechanical retentions and/or application of primers (DC 1205 primer and Sofreliner primer S) and adhesive (Silastic Medical Adhesive Type A) or not (control group). Samples were divided into 12 groups according to the method used to attach the silicone to the acrylic resin. All samples were subjected to a T-peel test in a universal testing machine. Failures were classified as adhesive, cohesive or mixed. The data were evaluated by the analysis of variance (ANOVA) and the Tukey's HSD test (α=.05). Results The highest bond strength values (5.95 N/mm; 3.07 N/mm; 4.75 N/mm) were recorded for the samples that received a Sofreliner primer application. These values were significantly higher when the samples had no scratches and did not receive the application of Silastic Medical Adhesive Type A. Conclusions The most common type of failure was adhesive. The use of Sofreliner primer increased the bond strength between the auto-polymerized acrylic resin and the Silastic MDX 4-4210 facial silicone. PMID:23329247

  13. 40 CFR 721.329 - Halogenated benzyl ester acrylate (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Halogenated benzyl ester acrylate (generic). 721.329 Section 721.329 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... substance may cause internal organ effects (kidney and blood). The requirements of this section do not...

  14. 40 CFR 721.329 - Halogenated benzyl ester acrylate (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Halogenated benzyl ester acrylate (generic). 721.329 Section 721.329 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... substance may cause internal organ effects (kidney and blood). The requirements of this section do not...

  15. 40 CFR 721.329 - Halogenated benzyl ester acrylate (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Halogenated benzyl ester acrylate (generic). 721.329 Section 721.329 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... substance may cause internal organ effects (kidney and blood). The requirements of this section do not...

  16. 40 CFR 721.329 - Halogenated benzyl ester acrylate (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Halogenated benzyl ester acrylate (generic). 721.329 Section 721.329 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... substance may cause internal organ effects (kidney and blood). The requirements of this section do not...

  17. 40 CFR 721.329 - Halogenated benzyl ester acrylate (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Halogenated benzyl ester acrylate (generic). 721.329 Section 721.329 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... substance may cause internal organ effects (kidney and blood). The requirements of this section do not...

  18. 21 CFR 175.210 - Acrylate ester copolymer coating.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... and holding food, including heating of prepared food, subject to the provisions of this section: (a... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Acrylate ester copolymer coating. 175.210 Section 175.210 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

  19. 21 CFR 175.210 - Acrylate ester copolymer coating.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... a food-contact surface of articles intended for packaging and holding food, including heating of... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Acrylate ester copolymer coating. 175.210 Section 175.210 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

  20. 21 CFR 175.210 - Acrylate ester copolymer coating.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... and holding food, including heating of prepared food, subject to the provisions of this section: (a... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Acrylate ester copolymer coating. 175.210 Section 175.210 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

  1. 21 CFR 175.210 - Acrylate ester copolymer coating.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... and holding food, including heating of prepared food, subject to the provisions of this section: (a... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Acrylate ester copolymer coating. 175.210 Section 175.210 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN...

  2. Acrylic resin injection method for blood vessel investigations.

    PubMed

    Suwa, Fumihiko; Uemura, Mamoru; Takemura, Akimichi; Toda, Isumi; Fang, Yi-Ru; Xu, Yuan Jin; Zhang, Zhi Yuan

    2013-01-01

    The injection of acrylic resin into vessels is an excellent method for macroscopically and microscopically observing their three-dimensional features. Conventional methods can be enhanced by removal of the polymerization inhibitor (hydroquinone) without requiring distillation, a consistent viscosity of polymerized resin, and a constant injection pressure and speed. As microvascular corrosion cast specimens are influenced by viscosity, pressure, and speed changes, injection into different specimens yields varying results. We devised a method to reduce those problems. Sodium hydroxide was used to remove hydroquinone from commercial methylmethacrylate. The solid polymer and the liquid monomer were mixed using a 1 : 9 ratio (low-viscosity acrylic resin, 9.07 ± 0.52 mPa•s) or a 3:7 ratio (high-viscosity resin, 1036.33 ± 144.02 mPa•s). To polymerize the acrylic resin for injection, a polymerization promoter (1.0% benzoyl peroxide) was mixed with a polymerization initiator (0.5%, N, N-dimethylaniline). The acrylic resins were injected using a precise syringe pump, with a 5-mL/min injection speed and 11.17 ± 1.60 mPa injection pressure (low-viscosity resin) and a 1-mL/min injection speed and 58.50 ± 5.75 mPa injection pressure (high-viscosity resin). Using the aforementioned conditions, scanning electron microscopy indicated that sufficient resin could be injected into the capillaries of the microvascular corrosion cast specimens.

  3. JKR studies of adhesion with model acrylic elastomers

    SciTech Connect

    Shull, K.R.; Ahn, D.

    1996-12-31

    Acrylic elastomers are widely used in coating applications because of their inherent thermal stability, oil resistance and adhesive properties. These same features make acrylic elastomers attractive for fundamental studies of polymer adhesion. This endeavor has been simplified recently by the development of techniques for producing monodisperse acrylic homopolymers and block copolymers from anionically synthesized parent polyacrylates, thus allowing precise microstructural control of adhering surfaces. In terms of the adhesion measurement itself, an adhesion test based upon the theory of Johnson, Kendall and Roberts (JKR), henceforth referred to as the JKR technique, is well suited for probing the molecular origins of adhesion in elastomeric systems. This technique is quite practical, and minimizes the sample volume to reduce bulk viscoelastic losses. Further, the JKR technique permits testing at very low crack velocities, where interfacial effects are unobscured by bulk effects. In this paper, the authors report the results of JKR adhesion tests between poly(n-butyl acrylate) (PNBA) elastomers and poly(methyl methacrylate) (PMMA). The latter is employed as a control substrate because its inertness and low surface energy (relative to metallic or silicon based surfaces) are conducive to the creation of reproducible solid surfaces.

  4. 21 CFR 177.1320 - Ethylene-ethyl acrylate copolymers.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... prescribed in paragraph (c)(2) of this section, when tested by the methods prescribed for polyethylene in... identified by their characteristic infrared spectra. (ii) Quantitative determination of ethyl acrylate... less than 0.920 nor more than 0.935, as determined by ASTM method D1505-68 (Reapproved 1979),...

  5. Antimicrobial activity of poly(acrylic acid) block copolymers.

    PubMed

    Gratzl, Günther; Paulik, Christian; Hild, Sabine; Guggenbichler, Josef P; Lackner, Maximilian

    2014-05-01

    The increasing number of antibiotic-resistant bacterial strains has developed into a major health problem. In particular, biofilms are the main reason for hospital-acquired infections and diseases. Once formed, biofilms are difficult to remove as they have specific defense mechanisms against antimicrobial agents. Antimicrobial surfaces must therefore kill or repel bacteria before they can settle to form a biofilm. In this study, we describe that poly(acrylic acid) (PAA) containing diblock copolymers can kill bacteria and prevent from biofilm formation. The PAA diblock copolymers with poly(styrene) and poly(methyl methacrylate) were synthesized via anionic polymerization of tert-butyl acrylate with styrene or methyl methacrylate and subsequent acid-catalyzed hydrolysis of the tert-butyl ester. The copolymers were characterized via nuclear magnetic resonance spectroscopy (NMR), size-exclusion chromatography (SEC), Fourier transform infrared spectroscopy (FTIR), elemental analysis, and acid-base titrations. Copolymer films with a variety of acrylic acid contents were produced by solvent casting, characterized by atomic force microscopy (AFM) and tested for their antimicrobial activity against Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa. The antimicrobial activity of the acidic diblock copolymers increased with increasing acrylic acid content, independent of the copolymer-partner, the chain length and the nanostructure.

  6. 40 CFR 721.336 - Perfluoroalkylethyl acrylate copolymer (generic name).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.336 Perfluoroalkylethyl acrylate copolymer (generic name). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified...

  7. 40 CFR 721.336 - Perfluoroalkylethyl acrylate copolymer (generic name).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.336 Perfluoroalkylethyl acrylate copolymer (generic name). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified...

  8. LC50 values for rats acutely exposed to vapors of acrylic and methacrylic acid esters

    SciTech Connect

    Oberly, R.; Tansy, M.F.

    1985-01-01

    Acute exposure studies were conducted using adult male Sprague-Dawley rats to obtain LC50/24 concentrations for the common esters of acrylic and methacrylic acids. The order of acute toxicity was determined to be methyl acrylate > ethyl acrylate > butyl acrylate > butyl methacrylate > methyl methacrylate > ethyl methacrylate. Four-hour daily exposures (excluding weekends) of young adult male rats to 110 ppm methyl acrylate in air over a period of 32 d failed to produce significant differences in body or tissue weights, blood chemistries, gross metabolic performance, and spontaneous small-intestinal motor activities when compared with a sham-exposed group.

  9. Synthesis and Characterization of Polyurethane Acrylates for UV Curable Coating Agents

    NASA Astrophysics Data System (ADS)

    Park, Mi Na; Kang, Young Soo; Oh, Sun Wha; Ahn, Byung Hyun; Moon, Myung Jun

    The single hydroxyl-terminated urethane acrylate oligomers were synthesized from 2-mercaptoethanol (2-MEOH), alkyl (methyl, butyl, and 2-ethylhexyl) acrylate, and 2,2-azobisisobutyronitrile (AIBN, initiator), with dibutyltin dilaurate (DBTDL) as a catalyst. 2-MEOH was used as a functional chain transfer agent. Poly(alkyl urethane) acrylate oligomers were obtained by the reaction of single hydroxyl-terminated polyalkyl acrylates and 2-isocyanatoethyl acrylate. They were characterized by NMR, FT-IR spectroscopy, rheometer, and DSC. Because poly(alkyl urethane) acrylate oligomers have lower Tg and viscosity than hydroxyl-terminated polyalkyl acrylate oligomers (HTPAO) non-containing urethane groups, they can be used for ultraviolet (UV) curable coatings, inks, and adhesives.

  10. Wavelength Shifters and Interactions of EDTA with Acrylic & LAB

    NASA Astrophysics Data System (ADS)

    Mohan, Yuvraj; SNO+ Collaboration

    2014-09-01

    The SNO + experiment, an upgrade to the Sudbury Neutrino Observatory, will use linear alkyl-benzene (LAB) liquid scintillator to probe new physics, including 0 νββ decay. Event detection efficiency is heavily affected by radioactive backgrounds, two sources being Rn-222 and Po-210 daughters, some of which has become embedded in the SNO + acrylic vessel after years underground. The leading candidate for polonium leaching is Ethylenediaminetetraacetic acid (EDTA). Before deployment on-site, EDTA's effects on the mechanical integrity of acrylic must be determined. It also must not be soluble in LAB or must be removed before scintillator fill of the vessel, as its presence would result in reduced light yield due to scattering. It was found that EDTA had negligible effects on the Young's Modulus of acrylic. EDTA is also slightly soluble in LAB, but can be completely removed by rinsing with water. Additionally, the study of the light yield and alpha/beta timing profiles of two wavelength shifters - bisMSB and perylene - is critical to determining which should be added to the 0 νββ isotope (tellurium) LAB cocktail. Small-scale results hint that perylene might be better, but this is being confirmed with larger-scale tests. The SNO + experiment, an upgrade to the Sudbury Neutrino Observatory, will use linear alkyl-benzene (LAB) liquid scintillator to probe new physics, including 0 νββ decay. Event detection efficiency is heavily affected by radioactive backgrounds, two sources being Rn-222 and Po-210 daughters, some of which has become embedded in the SNO + acrylic vessel after years underground. The leading candidate for polonium leaching is Ethylenediaminetetraacetic acid (EDTA). Before deployment on-site, EDTA's effects on the mechanical integrity of acrylic must be determined. It also must not be soluble in LAB or must be removed before scintillator fill of the vessel, as its presence would result in reduced light yield due to scattering. It was found that EDTA

  11. Chronic pulmonary dysfunction following acute inhalation of butyl acrylate.

    PubMed

    Bhardwaj, Ravindra; Ducatman, Alan; Finkel, Mitchell S; Petsonk, Edward; Hunt, Janet; Beto, Robert J

    2012-01-01

    Butyl Acrylate (BA) (2-propionic acid; CH2 = CHCOOC4H9) is a colorless liquid commonly used in impregnation agents and adhesives. Dermal contact with BA has previously been reported to cause moderate skin irritation with skin sensitizing potential in humans. Health effects of inhalation of BA have not been previously reported. Accordingly, we document the health conditions of a bystander, first responder and landfill worker exposed to butyl acrylate (BA) released to the atmosphere following a collision and roadside spill in October 1998. Retrospective data were collected via chart review and analyzed for exposure, symptoms, physical findings and radiological, laboratory and spirometry results over a ten-year period. All three patients had similar respiratory symptoms including a dramatic hacking cough and dyspnea. Findings included abnormal pulmonary function tests and breath sounds. These data underscore the potential hazards of BA inhalational exposure and the need to wear additional protective equipment. PMID:23472539

  12. A New Process for Acrylic Acid Synthesis by Fermentative Process

    NASA Astrophysics Data System (ADS)

    Lunelli, B. H.; Duarte, E. R.; de Toledo, E. C. Vasco; Wolf Maciel, M. R.; Maciel Filho, R.

    With the synthesis of chemical products through biotechnological processes, it is possible to discover and to explore innumerable routes that can be used to obtain products of high addes value. Each route may have particular advantages in obtaining a desired product, compared with others, especially in terms of yield, productivity, easiness to separate the product, economy, and environmental impact. The purpose of this work is the development of a deterministic model for the biochemical synthesis of acrylic acid in order to explore an alternative process. The model is built-up with the tubular reactor equations together with the kinetic representation based on the structured model. The proposed process makes possible to obtain acrylic acid continuously from the sugar cane fermentation.

  13. Dimensional stability of autopolymerizing acrylic resin impression trays.

    PubMed

    Fehling, A W; Hesby, R A; Pelleu, G B

    1986-05-01

    A study was undertaken to determine the optimal interval between fabrication of an autopolymerizing acrylic resin custom impression tray and making a final impression. Twenty mandibular arch-shaped trays, 10 each of Fastray and Formatray resin, were evaluated for dimensional change. Both materials behaved similarly. Cross-arch contraction of the borders of buccal flanges and unilateral expansion of the borders of buccal-to-lingual flanges were observed. These changes indicate distortion. Linear dimensional changes occurred throughout 6 hours, which suggests that any impression made in a methyl methacrylate acrylic resin custom impression tray should be poured as soon as is conveniently possible. Significant linear dimensional changes were observed for only 40 minutes from the initiation of tray fabrication. This study concludes that while an aged tray is preferred, it is acceptable to make an impression in an autopolymerizing resin custom impression tray after 40 minutes.

  14. Cytotoxicity of denture base acrylic resins: a literature review.

    PubMed

    Jorge, Janaina Habib; Giampaolo, Eunice Teresinha; Machado, Ana Lúcia; Vergani, Carlos Eduardo

    2003-08-01

    Acrylic resins are widely used in the fabrication of denture bases and have been shown to be cytotoxic as a result of substances that leach from the resin. The primary eluate is residual monomer. Numerous reports suggest that residual monomer may be responsible for mucosal irritation and sensitization of tissues. This information is important, not only to assess the biologic effects of such materials, but also to enable a comparison among the different polymerization methods, thus assisting the clinician in selecting a material with minimal cytotoxicity. This article reviews the literature published from 1973 to 2000, selected by use of a Medline search, associated with cytotoxic effects usually ascribed to acrylic denture base materials.

  15. Surface modification of nanoparticles for radiation curable acrylate clear coatings

    NASA Astrophysics Data System (ADS)

    Bauer, F.; Gläsel, H.-J.; Hartmann, E.; Bilz, E.; Mehnert, R.

    2003-08-01

    To obtain transparent, scratch and abrasion resistant coatings a high content of nanosized silica and alumina filler was embedded in radiation-curable acrylate formulations by acid catalyzed silylation using trialkoxysilanes. 29SiMAS NMR and MALDI-TOF mass spectrometry were employed to elucidate the structure of the surface-grafted methacryloxypropyl-, vinyl- and n-propyl-trimethoxysilane. In accordance with NMR findings, MALDI-TOF MS showed highly condensed oligomeric siloxanes of more than 20 monomeric silane units. A ladder-like structure of bound polysiloxanes is proposed rather than a simplified picture of tridentate silane bonding. Hence, silane coupling agents do not only modify the chemical nature of the filler surface but also strongly effect the rheological properties of the acrylate nanodispersions.

  16. Cellular Response to Linear and Branched Poly(acrylic acid).

    PubMed

    Whitty, Elizabeth G; Maniego, Alison R; Bentwitch, Sharon A; Guillaneuf, Yohann; Jones, Mark R; Gaborieau, Marianne; Castignolles, Patrice

    2015-12-01

    Poly(acrylic acid-co-sodium acrylate) (PNaA) is a pH-responsive polymer with potential in anticancer drug delivery. The cytotoxicity and intracellular effects of 3-arm star, hyperbranched and linear PNaA were investigated with L1210 progenitor leukemia cells and L6 myoblast cells. Free solution capillary electrophoresis demonstrated interactions of PNaA with serum proteins. In a 72 h MTT assay most PNaAs exhibited a IC50 between 7 and 14 mmol L(-1), showing that precipitation may be a sufficient purification for PNaA dilute solutions. Dialyzed 3-arm star and hyperbranched PNaA caused an increase in L6 cell viability, challenging the suitability of MTT as cytotoxicity assay for PNaA. Fluorescent confocal microscopy revealed merging of cellular lipids after exposure to PNaA, likely caused by serum starvation.

  17. Precipitation polymerization of acrylic acid in supercritical carbon dioxide

    SciTech Connect

    Romack, T.J.; Maury, E.E.; DeSimone, J.M.

    1995-02-13

    Increasing concern regarding the dissemination of chemical waste (both aqueous and organic) into their environment has prompted considerable interest in new technologies aimed at reducing current waste streams. Processes utilizing carbon dioxide in lieu of conventional solvents for chemical manufacturing and processing provide a viable route to achieving near-zero waste production for these important industries. The authors report the successful precipitation polymerization of acrylic acid in supercritical carbon dioxide at pressure ranging from 125 to 345 bar utilizing AIBN as a free radical initiator. Analyses by gel permeation chromatography (GPC) and scanning electron microscopy (SEM) indicate that for the pressure range studied there is no appreciable effect on product molecular weight, molecular weight distribution, or particle size or morphology. In addition, effective molecular weight control was demonstrated for precipitation polymerizations of acrylic acid in CO{sub 2} through the use of ethyl mercaptan as a chain transfer agent.

  18. Polymerization of acrylic acid using atmospheric pressure DBD plasma jet

    NASA Astrophysics Data System (ADS)

    Bashir, M.; Bashir, S.

    2016-08-01

    In this paper polymerization of acrylic acid was performed using non thermal atmospheric pressure plasma jet technology. The goal of this study is to deposit organic functional coatings for biomedical applications using a low cost and rapid growth rate plasma jet technique. The monomer solution of acrylic acid was vaporized and then fed into the argon plasma for coating. The discharge was powered using a laboratory made power supply operating with sinusoidal voltage signals at a frequency of 10 kHz. The optical emission spectra were collected in order to get insight into the plasma chemistry during deposition process. The coatings were characterized using Fourier transform infrared spectroscopy, atomic force microscopy and growth rates analysis. A high retention of carboxylic functional groups of the monomer was observed at the surface deposited using this low power technique.

  19. μPET imaging of the pharmacokinetic behavior of medium and high molar mass (89)Zr-labeled poly(2-ethyl-2-oxazoline) in comparison to poly(ethylene glycol).

    PubMed

    Wyffels, Leonie; Verbrugghen, Thomas; Monnery, Bryn D; Glassner, Mathias; Stroobants, Sigrid; Hoogenboom, Richard; Staelens, Steven

    2016-08-10

    Poly(2-oxazoline)s are a promising class of polymers for biomedical applications and a versatile alternative to poly(ethylene glycol)s (PEG). In this work, the pharmacokinetic behavior of well defined (89)Zr-labeled poly(2-ethyl-2-oxazoline)s (PEtOx) was evaluated and compared to that of (89)Zr-labeled PEG, both with varying molar mass. Amine-terminated PEtOx of low dispersity in a molar mass range of 20 to 110kDa and PEG of 20 and 40kDa were functionalized with a desferrioxamine chelator and radiolabeled with (89)Zr. The tissue distribution of both radiolabeled PEtOx and PEG polymers was studied by means of micro Positron Emission Tomography (μPET) molecular imaging in mice longitudinally up to 1week post injection, followed by ex vivo biodistribution. As previously described for other classes of non-ionic polymers, the blood clearance of PEtOx decreased with molar mass. The cut off for glomerular filtration of PEtOx is likely to be around 40kDa. The head to head comparison of PEG and PEtOx revealed that the biodistribution is mostly dominated by polymer chain length and not polymer molar mass. This study constitutes an important addition to further establishing PEtOx as a promising polymer in biomedical applications. PMID:27235979

  20. Acrylate functionalized tetraalkylammonium salts with ionic liquid properties.

    PubMed

    Grothe, Dorian C; Meyer, Wolfdietrich; Janietz, Silvia

    2012-01-01

    Acrylate functionalized ionic liquids based on tetraalkylammonium salts with terminal acrylates- and methylacrylates were synthesized. Melting points and ionic conductivity of twenty compounds in six groups were determined. Within one group the effect of three different counterions was investigated and discussed. The groups differ in cationic structure elements because of their functional groups such as acrylate and methacrylate, alkyl residues at the nitrogen and number of quaternary ammonium atoms within the organic cation. The effect of these cationic structure elements has been examined concerning the compiled parameters with a view to qualifying them as components for solid state electrolytes. The newly synthesized ionic liquids were characterized by NMR and FTIR analysis. The exchange of halide ions like bromide as counter ions to weakly coordinating [PF₆]⁻, [OTf]⁻ or [TFSI]⁻ reduces the melting points significantly and leads to an ion conductivity of about 10⁻⁴ S/cm at room temperature. In the case of the dicationic ionic liquid, an ion conductivity of about 10⁻³ S/cm was observed.

  1. Light-curing acrylic resin as an orthodontic baseplate material.

    PubMed

    Brown, J; Kerr, W J

    1998-08-01

    Heat-curing autopolymerizing (self-cure or cold-cure), thermoplastic, and light-curing acrylic resin are the most commonly used orthodontic baseplate materials. While cured acrylic resins present few problems to the patient, in the laboratory acrylic resin has to be sprayed, mixed, or packed in a fume-extraction unit because of the harmful fumes emitted by the raw inflammable chemicals. Light-curing material, on the other hand, is virtually nonflammable and has virtually no aroma. A light-cure technique for the construction of orthodontic baseplates is described. While buildup of the baseplate is slightly slower than for self-cured material, the shorter time involved in trimming and polishing means that overall construction is faster. It is easier to obtain a uniform thickness with light-cured material, and it provides superior fit. These results, however, are subject to more extensive clinical trials. The only apparent disadvantage is the fine powder produced during trimming. Even with a bench equipped with an extraction unit, it is advisable to use a face mask to prevent the inhalation of dust.

  2. Synthesis and properties of acrylic copolymers for ocular implants

    NASA Astrophysics Data System (ADS)

    Reboul, Adam C.

    There is a need for flexible polymers with higher refractive index and extended UV absorbing properties for improved intraocular lenses (IOLs). This research was devoted to the synthesis of new acrylic copolymers for foldable IOLs and to studies concerning IOL polymer properties. New polymers were synthesized from phenylated acrylates copolymerized with N-vinyl carbazole derivatives using bulk free radical addition methods. The copolymers had low Tg values, high refractive index, and were flexible. The N-vinyl carbazole derivatives were characterized by NMR and copolymers were characterized by DSC, UV-Vis, and refractometry. New phenothiazine based UV absorbers with high extinction coefficients were also synthesized for incorporation into ocular materials. Patent disclosures on UV absorbers and high refractive index polymers were prepared. A so called "glistening" phenomenon that occurs in all foldable intraocular lenses currently in clinical use is poorly understood and was studied. Research on this microvoid forming behavior included studies and development of methods to inhibit glistening in low Tg acrylic based copolymers. Glistenings were characterized using SEM and optical microscopy. A novel technique for inhibiting glistening was found and a patent disclosure was prepared.

  3. Acrylic microspheres-based optosensor for visual detection of nitrite.

    PubMed

    Noor, Nur Syarmim Mohamed; Tan, Ling Ling; Heng, Lee Yook; Chong, Kwok Feng; Tajuddin, Saiful Nizam

    2016-09-15

    A new optosensor for visual quantitation of nitrite (NO2(-)) ion has been fabricated by physically immobilizing Safranine O (SO) reagent onto a self-adhesive poly(n-butyl acrylate) [poly(nBA)] microspheres matrix, which was synthesized via facile microemulsion UV lithography technique. Evaluation and optimization of the optical NO2(-) ion sensor was performed with a fiber optic reflectance spectrophotometer. Scanning electron micrograph showed well-shaped and smooth spherical morphology of the poly(nBA) microspheres with a narrow particles size distribution from 0.6 μm up to 1.8 μm. The uniform size distribution of the acrylic microspheres promoted homogeneity of the immobilized SO reagent molecules on the microspheres' surfaces, thereby enhanced the sensing response reproducibility (<5% RSD) with a linear range obtained from 10 to 100 ppm NO2(-) ion. The micro-sized acrylic immobilization matrix demonstrated no significant barrier for diffusion of reactant and product, and served as a good solid state ion transport medium for reflectometric nitrite determination in food samples. PMID:27080889

  4. Formation of acrylic acid from lactic acid in supercritical water

    SciTech Connect

    Mok, W.S.L.; Antal, M.J. Jr. ); Jones, M. Jr. )

    1989-09-15

    Supercritical (SC) water is an unusual medium in which fast and specific heterolytic reactions can be conducted at temperatures as high as 400{degree}C. In supercritical water, lactic acid decomposes into gaseous and liquid products via three primary reaction pathways. Products of the acid-catalyzed heterolytic decarbonylation pathway are carbon monoxide, water, and acetaldehyde. Products of the homolytic, decarboxylation pathway are carbon dioxide, hydrogen, and acetaldehyde. Products of the heterolytic, dehydration pathway are acrylic acid and water. The intramolecular nucleophilic displacement of the {alpha}-hydroxyl by the carbonyl group of lactic acid, producing {alpha}-propiolactone as an unstable intermediate which subsequently rearranges to become the unsaturated acid, is a likely mechanism for acrylic acid formation, although an intramolecular E2 elimination initiated by attack of the carbonyl oxygen on a methyl hydrogen cannot be ruled out. Support for the former mechanism comes in part from the observed 100% relative yield of acrylic acid from {beta}-propiolactone in SC water.

  5. [Effect of acrylate industry wastes on the environment and the prevention of their harmful action].

    PubMed

    Tikhomirov, Iu P

    1991-01-01

    Acrylic and methacrylic++ acids and monomers as raw materials for production of polymers and copolymers are highly and extremely dangerous substances causing chronic intoxication. At low concentrations, acrylates and methacrylates++ have been found to produce not only systemic toxic, but embryotoxic effects. Manufacture of methacrylic++ and acrylic acids and monomers yields waste gases and waters that contain various acrylic compounds as impurities. The sewage treatment system introduced prevents the pollution of reservoirs with these compounds. High concentrations of acrylates and methacrylates are recorded in the sources of waste gases. It is required that fundamentally new waste--free technological processes for production of methacrylates++ and acrylates be designed and introduced and that the waste gas decontamination systems be improved in order to enhance the efficiency of measures to prevent environmental pollution.

  6. Preparation and properties of UV curable acrylic PSA by vinyl bonded graphene oxide

    NASA Astrophysics Data System (ADS)

    Pang, Beili; Ryu, Chong-Min; Jin, Xin; Kim, Hyung-Il

    2013-11-01

    Acrylic pressure sensitive adhesives (PSAs) with higher thermal stability for thin wafer handling were successfully prepared by forming composite with the graphene oxide (GO) nanoparticles modified to have vinyl groups via subsequent reaction with isophorone diisocyanate and 2-hydroxyethyl methacrylate. The acrylic copolymer was synthesized as a base resin for PSAs by solution radical polymerization of ethyl acrylate, 2-ethylhexyl acrylate, and acrylic acid followed by further modification with GMA to have the vinyl groups available for UV curing. The peel strength of PSA decreased with the increase of gel content which was dependent on both modified GO content and UV dose. Thermal stability of UV-cured PSA was improved noticeably with increasing the modified GO content mainly due to the strong and extensive interfacial bonding formed between the acrylic copolymer matrix and GO fillers

  7. Epoxy-acrylic core-shell particles by seeded emulsion polymerization.

    PubMed

    Chen, Liang; Hong, Liang; Lin, Jui-Ching; Meyers, Greg; Harris, Joseph; Radler, Michael

    2016-07-01

    We developed a novel method for synthesizing epoxy-acrylic hybrid latexes. We first prepared an aqueous dispersion of high molecular weight solid epoxy prepolymers using a mechanical dispersion process at elevated temperatures, and we subsequently used the epoxy dispersion as a seed in the emulsion polymerization of acrylic monomers comprising methyl methacrylate (MMA) and methacrylic acid (MAA). Advanced analytical techniques, such as scanning transmission X-ray microscopy (STXM) and peak force tapping atomic force microscopy (PFT-AFM), have elucidated a unique core-shell morphology of the epoxy-acrylic hybrid particles. Moreover, the formation of the core-shell morphology in the seeded emulsion polymerization process is primarily attributed to kinetic trapping of the acrylic phase at the exterior of the epoxy particles. By this new method, we are able to design the epoxy and acrylic polymers in two separate steps, and we can potentially synthesize epoxy-acrylic hybrid latexes with a broad range of compositions. PMID:27078740

  8. Epoxy-acrylic core-shell particles by seeded emulsion polymerization.

    PubMed

    Chen, Liang; Hong, Liang; Lin, Jui-Ching; Meyers, Greg; Harris, Joseph; Radler, Michael

    2016-07-01

    We developed a novel method for synthesizing epoxy-acrylic hybrid latexes. We first prepared an aqueous dispersion of high molecular weight solid epoxy prepolymers using a mechanical dispersion process at elevated temperatures, and we subsequently used the epoxy dispersion as a seed in the emulsion polymerization of acrylic monomers comprising methyl methacrylate (MMA) and methacrylic acid (MAA). Advanced analytical techniques, such as scanning transmission X-ray microscopy (STXM) and peak force tapping atomic force microscopy (PFT-AFM), have elucidated a unique core-shell morphology of the epoxy-acrylic hybrid particles. Moreover, the formation of the core-shell morphology in the seeded emulsion polymerization process is primarily attributed to kinetic trapping of the acrylic phase at the exterior of the epoxy particles. By this new method, we are able to design the epoxy and acrylic polymers in two separate steps, and we can potentially synthesize epoxy-acrylic hybrid latexes with a broad range of compositions.

  9. Development of palm oil-based UV-curable epoxy acrylate and urethane acrylate resins for wood coating application

    SciTech Connect

    Tajau, Rida; Mahmood, Mohd Hilmi; Salleh, Mek Zah; Salleh, Nik Ghazali Nik; Ibrahim, Mohammad Izzat; Yunus, Nurulhuda Mohd

    2014-02-12

    The trend of using renewable sources such as palm oil as raw material in radiation curing is growing due to the demand from the market to produce a more environmental friendly product. In this study, the radiation curable process was done using epoxy acrylate and urethane acrylate resins which are known as epoxidised palm olein acrylate (EPOLA) and palm oil based urethane acrylate (POBUA), respectively. The purpose of the study was to investigate curing properties and the application of this UV-curable palm oil resins for wood coating. Furthermore, the properties of palm oil based coatings are compared with the petrochemical-based compound such as ebecryl (EB) i.e. EB264 and EB830. From the experiment done, the resins from petrochemical-based compounds resulted higher degree of crosslinking (up to 80%) than the palm oil based compounds (up to 70%), where the different is around 10-15%. The hardness property from this two type coatings can reached until 50% at the lower percentage of the oligomer. However, the coatings from petrochemical-based have a high scratch resistance as it can withstand at least up to 3.0 Newtons (N) compared to the palm oil-based compounds which are difficult to withstand the load up to 1.0 N. Finally, the test on the rubber wood substrate showed that the coatings containing benzophenone photoinitiator give higher adhesion property and their also showed a higher glosiness property on the glass substrate compared to the coatings containing irgacure-819 photoinitiator. This study showed that the palm oil coatings can be a suitable for the replacement of petrochemicals compound for wood coating. The palm oil coatings can be more competitive in the market if the problems of using high percentage palm oil oligomer can be overcome as the palm oil price is cheap enough.

  10. Development of palm oil-based UV-curable epoxy acrylate and urethane acrylate resins for wood coating application

    NASA Astrophysics Data System (ADS)

    Tajau, Rida; Ibrahim, Mohammad Izzat; Yunus, Nurulhuda Mohd; Mahmood, Mohd Hilmi; Salleh, Mek Zah; Salleh, Nik Ghazali Nik

    2014-02-01

    The trend of using renewable sources such as palm oil as raw material in radiation curing is growing due to the demand from the market to produce a more environmental friendly product. In this study, the radiation curable process was done using epoxy acrylate and urethane acrylate resins which are known as epoxidised palm olein acrylate (EPOLA) and palm oil based urethane acrylate (POBUA), respectively. The purpose of the study was to investigate curing properties and the application of this UV-curable palm oil resins for wood coating. Furthermore, the properties of palm oil based coatings are compared with the petrochemical-based compound such as ebecryl (EB) i.e. EB264 and EB830. From the experiment done, the resins from petrochemical-based compounds resulted higher degree of crosslinking (up to 80%) than the palm oil based compounds (up to 70%), where the different is around 10-15%. The hardness property from this two type coatings can reached until 50% at the lower percentage of the oligomer. However, the coatings from petrochemical-based have a high scratch resistance as it can withstand at least up to 3.0 Newtons (N) compared to the palm oil-based compounds which are difficult to withstand the load up to 1.0 N. Finally, the test on the rubber wood substrate showed that the coatings containing benzophenone photoinitiator give higher adhesion property and their also showed a higher glosiness property on the glass substrate compared to the coatings containing irgacure-819 photoinitiator. This study showed that the palm oil coatings can be a suitable for the replacement of petrochemicals compound for wood coating. The palm oil coatings can be more competitive in the market if the problems of using high percentage palm oil oligomer can be overcome as the palm oil price is cheap enough.

  11. Studies on the hydrolysis of biocompatible acrylic polymers having aspirin-moieties.

    PubMed

    Gu, Z W; Li, F M; Feng, X D; Voong, S T

    1983-01-01

    Both the homogeneous and heterogeneous hydrolysis of five new acrylic polymers having aspirin-moieties, i.e. polymers of beta-(acetylsalicylyloxy)ethyl methacrylate, beta-(acetylsalicylyloxy) propyl methacrylate,beta-(acetylsalicylyloxy) ethyl acrylate, beta-hydroxy-gamma-(acetylsalicylyloxy) propyl methacrylate, beta-hydroxy-gamma-(acetylsalicylyloxy) propyl acrylate were investigated in acidic or alkaline medium at 30 degrees C or 60 degrees C, respectively. It was observed that the chief hydrolyzed product is always aspirin with minor amount of salicylic acid.

  12. N-Butyl acrylate polymer composition for solar cell encapsulation and method

    NASA Technical Reports Server (NTRS)

    Gupta, Amitava (Inventor); Ingham, John D. (Inventor); Yavrouian, Andre H. (Inventor)

    1983-01-01

    A polymer syrup for encapsulating solar cell assemblies. The syrup includes uncrosslinked poly(n-butyl)acrylate dissolved in n-butyl acrylate monomer. Preparation of the poly(n-butyl)acrylate and preparation of the polymer syrup is disclosed. Methods for applying the polymer syrup to solar cell assemblies as an encapsulating pottant are described. Also included is a method for solar cell construction utilizing the polymer syrup as a dual purpose adhesive and encapsulating material.

  13. Acrylic coatings compositions containing polymer-bound hindered amine light stabilizers

    SciTech Connect

    Callais, P.A.

    1993-12-31

    Unique acrylic coatings resins with attached hindered amine light stabilizer (HALS) groups have been developed. They are readily prepared by reacting a hydrazide functionalized HALS with an acrylic polyol resin containing anhydride and/or epoxy groups or with a peroxide functionalized HALS as the polymerization initiator. As a result, the HALS moiety is rendered nonvolatile and nonextractable. Acrylic melamine and acrylic urethane coatings prepared from the polymer-bound light stabilizer resins exhibit outstanding weatherability and durability in both accelerated and outdoor weathering.

  14. Effect of 5.25 % sodium hypochlorite on color stability of acrylic and silicone based soft liners and a denture base acrylic resin.

    PubMed

    Salloum, Alaa'a M

    2014-06-01

    The purpose of the current study was to investigate the effect of a chemical disinfectant (sodium hypochlorite 5.25 %) on color stability of a denture base acrylic resin and two processed soft denture lining materials of two different types (acrylic-based and silicone-based). Ten specimens from each type of materials tested were made (2 × 20 × 20 mm). All specimens were immersed in sodium hypochlorite (5.25 %). Colorimetric measurements for each specimen were taken before immersion, and after 24 h and 7 days of immersion. Color changes were evaluated using the CIE L*a*b* colorimetric system. Data were statistically analyzed with one-way analysis of variance (ANOVA) (α = 0.05). ANOVA was followed by Bonferroni test to determine which groups differed from each other. ΔE and ΔL* of the silicone-based liner at the 1st and 7th days of immersion were significantly more than of denture base acrylic resin and acrylic-based liner. Change in ΔL* values of denture base acrylic resin and acrylic-based liner was small and statistically insignificant after 24 h of its immersion. However, the increase in ΔL* values of the acrylic-based liner after 7 days of immersion was considerably more than of denture base acrylic resin. Color changes in denture base acrylic resin and soft denture liners tended to increase with longer immersion times, and the color stability of the soft denture liners was influenced by its chemical type.

  15. Delayed recombination of detrapped space-charge carriers in poly[2-methoxy-5-(2'-ethyl-hexyloxy)-1,4-phenylene vinylene]-based light-emitting diode

    NASA Astrophysics Data System (ADS)

    Sinha, S.; Monkman, A. P.

    2005-06-01

    We report the observation of a spectroscopically resolved delayed electrofluorescence (DEF) in the time domain of nanosecond to microsecond (depending on temperature, in the range of 30-290 K, as well as bias) from light-emitting diodes based on poly[2-methoxy-5-(2'-ethyl-hexyloxy)-1,4-phenylene vinylene]. The decay kinetics of this DEF are always found to be biexponential in nature. The fast decaying component with a lifetime of ˜40ns is attributed to the back transfer of nonemissive (or very weakly emissive) interchain excited singlets (partially charge-transfer states) to emissive intrachain excited singlets (this component is called DEFCT). The relatively slower decaying component with a lifetime of ˜0.2-6.2μs (depending on temperature as well as bias) is attributed to the recombination of detrapped space-charge carriers at the polymer-electrode interfaces (this component is called DEFSC). The intensity of DEFSC increases as the temperature is increased from 30 to 290 K, although it is weak at low temperature (<100K). The temperature dependence of the recombination rate of the detrapped space-charge carriers yields two activation energies of 2.2 and 40 meV below and above ˜130K, respectively. The existence of these two activation energies is explained on the assumption of electrons being in shallow traps and holes in deep traps. Also, our data indicate that the space-charge carriers generally act as major quenching sites (especially at 290 K) for triplet excitons in polymer light-emitting diodes.

  16. ALA and ALA hexyl ester-induced porphyrin synthesis in chemically induced skin tumours: the role of different vehicles on improving photosensitization.

    PubMed

    Casas, A; Perotti, C; Fukuda, H; Rogers, L; Butler, A R; Batlle, A

    2001-11-30

    Exogenous administration of 5-aminolevulinic acid (ALA) is becoming widely used to enhance the endogenous synthesis of Protoporphyrin IX (PpIX) in photodynamic therapy. We analysed porphyrin formation in chemically induced squamous papillomas, after topical application of ALA and ALA hexyl ester (He-ALA) administered in different formulations, as well as the pattern of distribution in the internal organs, and the synthesis of porphyrins in distant tumoural and normal skins. A lotion formulation containing DMSO and ethanol was the best vehicle for topical ALA delivery to papillomas, whereas cream was the most efficient formulation for He-ALA application. Similar porphyrin concentration can be accumulated in the skin tumours employing either ALA or He-ALA delivered in their optimal formulations. The use of cream as a vehicle of both ALA and He-ALA, induces highest porphyrin tumour/normal skin ratios. The main advantage of using He-ALA is that porphyrins synthesized from the ester are more confined to the site of application, thus inducing low porphyrin levels in normal skin, liver, blood and spleen, as well as in papillomas distant from the point of application, independently on the vehicle employed, so reducing potential side effects of photodynamic therapy.

  17. Crystal structure of an aryl cyclo­hexyl nona­noid, an anti­proliferative mol­ecule isolated from the spice Myristica malabarica

    PubMed Central

    Bauri, Ajoy Kumar; Foro, Sabine; Do, Nhu Quynh Nguyen

    2016-01-01

    The title compound, C21H26O5, an aryl cyclo­hexyl nona­noid {systematic name: 3,5-dihy­droxy-2-[9-(4-hy­droxy­phen­yl)nona­noyl]cyclo­hexa-2,4-dien-1-one}, extracted from the spice plant Myristica malabarica comprises two ring components, a 4-hy­droxy­phenyl moiety and a 3,5-di­hydroxy­cyclo­hexa-2,4-dienone moiety linked by a nona­noyl chain. The mol­ecule has an extended essentially planar conformation stabilized by an intra­molecular hy­droxy O—H⋯Ocarbon­yl hydrogen bond, giving a dihedral angle between the two ring systems of 6.37 (15)°. The C, O and H atoms associated with one of the hy­droxy groups of the cyclo­hexa­dienone component are disordered over two sets of sites with site occupancies of 0.6972 and 0.3028. In the crystal, hy­droxy O—H⋯O hydrogen bonds to carbonyl O-atom acceptors form large centrosymmetric R 2 2(36) cyclic dimers, which are further extended into supra­molecular one-dimensional ribbon structures along [1-11]. PMID:27746930

  18. Crystal structure of bis­(1-hexyl-N,N-di­methyl­pyridinium) bis­(maleo­nitrile­dithiol­ato)nickelate(II)

    PubMed Central

    Yu, Shan-Shan; Zhang, Hui

    2016-01-01

    The asymmetric unit of the title compound, (C13H23N2)2[Ni(C4N2S2)2], consists of a 1-hexyl-N,N-di­methyl­pyridinium cation and one half of a [Ni(mnt)2]2− dianion (mnt2− = maleo­nitrile­dithiol­ate) in which the Ni2+ cation lies on a crystallographic inversion centre. The square-planar coordination about Ni2+ comprises four S atoms from two bidentate chelate mnt2− ligands [Ni—S = 2.1791 (9) and 2.1810 (8) Å, and S—Ni—S bite angle = 91.93 (3)°]. The hydro­carbon chains of cations show trans-planar conformations and lie approximately parallel to the long mol­ecular axis of the [Ni(mnt)2]2− anions, giving stacks along the c axis. The anions and cations form layers lying parallel to the bc plane. Only weak C—H⋯Ni and C—H⋯π associations are present in the crystal packing. PMID:27536413

  19. Red versus blue light illumination in hexyl 5-aminolevulinate photodynamic therapy: the influence of light color and irradiance on the treatment outcome in vitro.

    PubMed

    Helander, Linda; Krokan, Hans E; Johnsson, Anders; Gederaas, Odrun A; Plaetzer, Kristjan

    2014-08-01

    Hexyl 5-aminolevulinate (HAL) is a lipophilic derivative of 5-aminolevulinate, a key intermediate in biosynthesis of the photosensitizer protoporphyrin IX (PpIX). The photodynamic efficacy and cell death mode after red versus blue light illumination of HAL-induced PpIX have been examined and compared using five different cancer cell lines. LED arrays emitting at 410 and 624 nm served as homogenous and adjustable light sources. Our results show that the response after HAL-PDT is cell line specific, both regarding the shape of the dose-survival curve, the overall dose required for efficient cell killing, and the relative amount of apoptosis. The ratio between 410 and 624 nm in absorption coefficient correlates well with the difference in cell killing at the same wavelengths. In general, the PDT efficacy was several folds higher for blue light as compared with red light, as expected. However, HAL-PDT₆₂₄ induced more apoptosis than HAL-PDT₄₁₀ and illumination with low irradiance resulted in more apoptosis than high irradiance at the same lethal dose. This indicates differences in death modes after low and high irradiance after similar total light doses. From a treatment perspective, these differences may be important.

  20. Red versus blue light illumination in hexyl 5-aminolevulinate photodynamic therapy: the influence of light color and irradiance on the treatment outcome in vitro

    NASA Astrophysics Data System (ADS)

    Helander, Linda; Krokan, Hans E.; Johnsson, Anders; Gederaas, Odrun A.; Plaetzer, Kristjan

    2014-08-01

    Hexyl 5-aminolevulinate (HAL) is a lipophilic derivative of 5-aminolevulinate, a key intermediate in biosynthesis of the photosensitizer protoporphyrin IX (PpIX). The photodynamic efficacy and cell death mode after red versus blue light illumination of HAL-induced PpIX have been examined and compared using five different cancer cell lines. LED arrays emitting at 410 and 624 nm served as homogenous and adjustable light sources. Our results show that the response after HAL-PDT is cell line specific, both regarding the shape of the dose-survival curve, the overall dose required for efficient cell killing, and the relative amount of apoptosis. The ratio between 410 and 624 nm in absorption coefficient correlates well with the difference in cell killing at the same wavelengths. In general, the PDT efficacy was several folds higher for blue light as compared with red light, as expected. However, HAL-PDT624 induced more apoptosis than HAL-PDT410 and illumination with low irradiance resulted in more apoptosis than high irradiance at the same lethal dose. This indicates differences in death modes after low and high irradiance after similar total light doses. From a treatment perspective, these differences may be important.

  1. Grape contribution to wine aroma: production of hexyl acetate, octyl acetate, and benzyl acetate during yeast fermentation is dependent upon precursors in the must.

    PubMed

    Dennis, Eric G; Keyzers, Robert A; Kalua, Curtis M; Maffei, Suzanne M; Nicholson, Emily L; Boss, Paul K

    2012-03-14

    Wine is a complex consumer product produced predominately by the action of yeast upon grape juice musts. Model must systems have proven ideal for studies of the effects of fermentation conditions on the production of certain wine volatiles. To identify grape-derived precursors to acetate esters, model fermentation systems were developed by spiking precursors into model must at different concentrations. Solid-phase microextraction-gas chromatgraphy mass spectrometry analysis of the fermented wines showed that a variety of grape-derived aliphatic alcohols and aldehydes are precursors to acetate esters. The C6 compounds hexan-1-ol, hexenal, (E)-2-hexen-1-ol, and (E)-2-hexenal are all precursors to hexyl acetate, and octanol and benzyl alcohol are precursors to octyl acetate and benzyl acetate, respectively. In these cases, the postfermentation concentration of an acetate ester increased proportionally with the prefermentation concentration of the respective precursor in the model must. Determining viticultural or winemaking methods to alter the prefermentation concentration of precursor compounds or change the precursor-to-acetate ester ratio will have implications upon the final flavor and aroma of wines. PMID:22332880

  2. Ultrafast transient absorption spectrum of the room temperature Ionic liquid 1-hexyl-3-methylimidazolium bromide: Confounding effects of photo-degradation

    NASA Astrophysics Data System (ADS)

    Musat, Raluca M.; Crowell, Robert A.; Polyanskiy, Dmitriy E.; Thomas, Marie F.; Wishart, James F.; Katsumura, Yosuke; Takahashi, Kenji

    2015-12-01

    The photochemistry of the charge transfer (CT) band of the room temperature ionic liquid (RTIL) 1-hexyl-3-methylimidazolium bromide (HMIm+/Br-) is investigated using near-IR to vis ultrafast transient absorption (TA) and steady-state UV absorption spectroscopies. Continuous irradiation of the CT band at 266 nm results in the formation of photo-products that absorb strongly at 266 nm. It is shown that these photo-products, which are apparently very stable, adversely affect ultrafast TA measurements. Elimination of these effects reveals at least two transient species that exist within the TA detection window of 100 fs to 3 ns and 500-1250 nm. One of the components is a short-lived (<1 ps) species that absorbs at 1080 nm. The second band exhibits a multicomponent spectrum that is very broad with an absorption maximum around 600 nm and a lifetime that is longer than the 3 ns window of our TA spectrometer. Within the signal to noise ratio of the TA spectrometer little to no solvated electron is generated by the CT mechanism.

  3. Heteroleptic Ru(ii)-bipyridine complexes based on hexylthioether-, hexyloxy- and hexyl-substituted thienylenevinylenes and their application in dye-sensitized solar cells.

    PubMed

    Urbani, Maxence; Sánchez Carballo, María; Kumar, Sangeeta Amit; Vázquez, Purificación; Grätzel, Michael; Khaja Nazeeruddin, Mohammad; Langa, Fernando; Torres, Tomás

    2016-04-28

    A series of eight Ru(ii) heteroleptic complexes incorporating an ancillary [2,2']bipyridine functionalised at the [4,4'] positions with one (-type) or two (-type) thienylenevinylenes (nTVs, n = 2 or 4) is reported. Three types of substitutions have been used for nTVs: hexylthioether, hexyloxy and hexyl. The characterisation of the half-sandwich intermediates and final complexes is provided. In particular, the half-sandwich complexes in the -type series are obtained as a racemate, whereas the heteroleptic complexes consist of two regioisomers. Finally, these complexes have been tested as dyes in dye-sensitized solar cells (DSSCs). Counterintuitively, better performances were obtained for -type complexes with shorter 2TV moieties. The best performing dye was the Ru(ii) complex mono-functionalized with a 2TV moiety having an hexylthioether substitution (), which achieved a maximum power efficiency of 2.77% under full sun illumination (AM1.5G standard conditions). The structure-performance relationship in DSSCs is discussed based on photovoltaic and electrochemical data and DFT-calculations.

  4. Heteroleptic Ru(ii)-bipyridine complexes based on hexylthioether-, hexyloxy- and hexyl-substituted thienylenevinylenes and their application in dye-sensitized solar cells.

    PubMed

    Urbani, Maxence; Sánchez Carballo, María; Kumar, Sangeeta Amit; Vázquez, Purificación; Grätzel, Michael; Khaja Nazeeruddin, Mohammad; Langa, Fernando; Torres, Tomás

    2016-04-28

    A series of eight Ru(ii) heteroleptic complexes incorporating an ancillary [2,2']bipyridine functionalised at the [4,4'] positions with one (-type) or two (-type) thienylenevinylenes (nTVs, n = 2 or 4) is reported. Three types of substitutions have been used for nTVs: hexylthioether, hexyloxy and hexyl. The characterisation of the half-sandwich intermediates and final complexes is provided. In particular, the half-sandwich complexes in the -type series are obtained as a racemate, whereas the heteroleptic complexes consist of two regioisomers. Finally, these complexes have been tested as dyes in dye-sensitized solar cells (DSSCs). Counterintuitively, better performances were obtained for -type complexes with shorter 2TV moieties. The best performing dye was the Ru(ii) complex mono-functionalized with a 2TV moiety having an hexylthioether substitution (), which achieved a maximum power efficiency of 2.77% under full sun illumination (AM1.5G standard conditions). The structure-performance relationship in DSSCs is discussed based on photovoltaic and electrochemical data and DFT-calculations. PMID:26935911

  5. Crystal structure of S-hexyl (E)-3-(2-hy­droxy­benzyl­idene)di­thio­carbazate

    PubMed Central

    Begum, M. S.; Howlader, M. B. H.; Sheikh, M. C.; Miyatake, R.; Zangrando, E.

    2016-01-01

    The title compound, C14H20N2OS2 [systematic name: S-hexyl (E)-2-(2-hy­droxy­benzyl­idene)hydrazine-1-carbodi­thio­ate], crystallizes with four independent mol­ecules (A–D) in the asymmetric unit. All four mol­ecules adopt an E conformation with respect to the C=N bond of the benzyl­idene moiety and have an intra­molecular O—H⋯N hydrogen bond generating an S(6) ring motif. In the crystal, the A and D mol­ecules are connected by a pair N—H⋯S hydrogen bonds, forming a dimer with an R 2 2(8) ring motif. In the case of mol­ecules B and C, they are linked to themselves by pairs of N—H⋯S hydrogen bonds, forming B–B and C–C inversion dimers with R 2 2(8) ring motifs. PMID:27006789

  6. ALA and ALA hexyl ester-induced porphyrin synthesis in chemically induced skin tumours: the role of different vehicles on improving photosensitization

    PubMed Central

    Casas, A; Perotti, C; Fukuda, H; Rogers, L; Butler, A R; Batlle, A

    2001-01-01

    Exogenous administration of 5-aminolevulinic acid (ALA) is becoming widely used to enhance the endogenous synthesis of Protoporphyrin IX (PpIX) in photodynamic therapy. We analysed porphyrin formation in chemically induced squamous papillomas, after topical application of ALA and ALA hexyl ester (He-ALA) administered in different formulations, as well as the pattern of distribution in the internal organs, and the synthesis of porphyrins in distant tumoural and normal skins. A lotion formulation containing DMSO and ethanol was the best vehicle for topical ALA delivery to papillomas, whereas cream was the most efficient formulation for He-ALA application. Similar porphyrin concentration can be accumulated in the skin tumours employing either ALA or He-ALA delivered in their optimal formulations. The use of cream as a vehicle of both ALA and He-ALA, induces highest porphyrin tumour/normal skin ratios. The main advantage of using He-ALA is that porphyrins synthesized from the ester are more confined to the site of application, thus inducing low porphyrin levels in normal skin, liver, blood and spleen, as well as in papillomas distant from the point of application, independently on the vehicle employed, so reducing potential side effects of photodynamic therapy. © 2001 Cancer Research Campaign http://www.bjcancer.com PMID:11742504

  7. Role of 2-hexyl, 5-propyl resorcinol production by Pseudomonas chlororaphis PCL1606 in the multitrophic interactions in the avocado rhizosphere during the biocontrol process.

    PubMed

    Calderón, Claudia E; de Vicente, Antonio; Cazorla, Francisco M

    2014-07-01

    Different bacterial traits can contribute to the biocontrol of soilborne phytopathogenic fungus. Among others, (1) antagonism, (2) competition for nutrients and niches, (3) induction of systemic resistance of the plants and (4) predation and parasitism are the most studied. Pseudomonas chlororaphis PCL1606 is an antagonistic rhizobacterium that produces the antifungal metabolite 2-hexyl, 5-propyl resorcinol (HPR). This bacterium can biologically control the avocado white root rot caused by Rosellinia necatrix. Confocal laser scanning microscopy of the avocado rhizosphere revealed that this biocontrol bacterium and the fungal pathogen compete for the same niche and presumably also for root exudate nutrients. The use of derivative mutants in the geners related to HPR biosynthesis (dar genes) revealed that the lack of HPR production by P. chlororaphis PCL1606 negatively influences the bacterial colonisation of the avocado root surface. Microscopical analysis showed that P. chlororaphis PCL1606 closely interacts and colonises the fungal hyphae, which may represent a novel biocontrol mechanism in this pseudomonad. Additionally, the presence of HPR-producing biocontrol bacteria negatively affects the ability of the fungi to infect the avocado root. HPR production negatively affects hyphal growth, leading to alterations in the R. necatrix physiology visible under microscopy, including the curling, vacuolisation and branching of hyphae, which presumably affects the colonisation and infection abilities of the fungus. This study provides the first report of multitrophic interactions in the avocado rhizosphere, advancing our understanding of the role of HPR production in those interactions.

  8. Thermal stability and structural study of the poly(3-hexyl thiophene)/HiPCO single walled carbon nanotubes (P3HT/SWCNT) nanocomposites

    NASA Astrophysics Data System (ADS)

    Bakour, Anass; Baitoul, Mimouna; Faulques, Eric; Wery-Venturini, Jany

    2016-05-01

    In this work we present the effect of HiPCO single walled carbon nanotubes (SWCNT) introduction into the conjugated polymer matrix poly(3-hexyl thiophene) (P3HT) on the structural and thermal stability of these nanocomposites. The P3HT/SWCNT nanocomposite films were prepared using chloroform and chlorobenzene as solvents and optimised ultrasonication duration. The prepared samples were analyzed by thermogravimetric analysis (TGA), X-ray diffraction and transmission electron microscopy (TEM) to study the effect of carbon nanotubes on the thermal stability and structure of the polymer matrix. The measurements carried out for different SWCNT loadings show that the thermal stability was enhanced for a 0.5 wt.%, but exhibits a decrease with increasing the SWCNT content. Our results prove the structural enhancement which is in favor of a better organisation for both P3HT chains and carbon nanotubes due to their interaction. Contribution to the topical issue "Materials for Energy Harvesting, Conversion and Storage (ICOME 2015) - Elected submissions", edited by Jean-Michel Nunzi, Rachid Bennacer and Mohammed El Ganaoui

  9. Tissue responses to hexyl 5-aminolevulinate-induced photodynamic treatment in syngeneic orthotopic rat bladder cancer model: possible pathways of action

    NASA Astrophysics Data System (ADS)

    Arum, Carl-Jørgen; Gederaas, Odrun A.; Larsen, Eivind L. P.; Randeberg, Lise L.; Hjelde, Astrid; Krokan, Hans E.; Svaasand, Lars O.; Chen, Duan; Zhao, Chun-Mei

    2011-02-01

    Orthotopic bladder cancer model in rats mimics human bladder cancer with respect to urothelial tumorigenesis and progression. Utilizing this model at pT1 (superficial stage), we analyze the tissue responses to hexyl 5-aminolevulinate-induced photodynamic therapy (HAL-PDT). In comparison to untreated rats, HAL-PDT causes little change in tumor-free rat bladder but induces inflammatory changes with increased lymphocytes and mononuclear cell infiltration in rat bladders with tumor. Immunohistochemistry reveals that HAL-PDT is without effect on proliferating cell nuclear antigen expression within the tumor and increases caspase-3 expression in both normal urothelium and the tumor. Transmission electron microscopy reveals severe mitochondrial damage, formations of apoptotic bodies, vacuoles, and lipofuscin bodies, but no microvillus-formed niches in HAL-PDT-treated bladder cancer rats. Bioinformatics analysis of the gene expression profile indicates an activation of T-cell receptor signaling pathway in bladder cancer rats without PDT. HAL-PDT increases the expression of CD3 and CD45RA in the tumor (determined by immunohistochemistry). We suggest that pathways of action of HAL-PDT may include, at least, activations of mitochondrial apoptosis and autophagy, breakdown of cancer stem cell niches, and importantly, enhancement of T-cell activation.

  10. Anomerization of Acrylated Glucose During Traveling Wave Ion Mobility Spectrometry

    NASA Astrophysics Data System (ADS)

    Chendo, Christophe; Moreira, Guillaume; Tintaru, Aura; Posocco, Paola; Laurini, Erik; Lefay, Catherine; Gigmes, Didier; Viel, Stéphane; Pricl, Sabrina; Charles, Laurence

    2015-09-01

    Anomerization of simple sugars in the liquid phase is known as an acid- and base-catalyzed process, which highly depends on solvent polarity. This reaction is reported here to occur in the gas phase, during traveling wave ion mobility spectrometry (TWIMS) experiments aimed at separating α- and β-anomers of penta-acrylated glucose generated as ammonium adducts in electrospray ionization. This compound was available in two samples prepared from glucose dissolved in solvents of different polarity, namely tetrahydrofuran (THF) and N,N-dimethylacetamide (DMAC), and analyzed by electrospray tandem mass spectrometry (ESI-MS/MS) as well as traveling wave ion mobility (ESI-TWIMS-MS). In MS/MS, an anchimerically-assisted process was found to be unique to the electrosprayed α-anomer, and was only observed for the THF sample. In ESI-TWIMS-MS, a signal was measured at the drift time expected for the α-anomer for both the THF and DMAC samples, in apparent contradiction to the MS/MS results, which indicated that the α-anomer was not present in the DMAC sample. However, MS/MS experiments performed after TWIMS separation revealed that ammonium adducts of the α-anomer produced from each sample, although exhibiting the same collision cross section, were clearly different. Indeed, while the α-anomer actually present in the THF sample was electrosprayed with the ammonium adducted at the C2 acrylate, its homologue only observed when the DMAC sample was subjected to TWIMS hold the adducted ammonium at the C1 acrylate. These findings were explained by a β/α inter-conversion upon injection in the TWIMS cell, as supported by theoretical calculation and dynamic molecular modeling.

  11. Photostabilization of polymeric materials by photoset acrylate coatings

    NASA Astrophysics Data System (ADS)

    Decker, C.; Zahouily, K.

    2002-01-01

    Different types of polymeric materials have been made more resistant to photodegradation by protecting their surface with a UV-cured coating containing a HALS radical scavenger and a phenyltriazine UV absorber. The tridimensional polymer network formed by photopolymerization of an aliphatic polyurethane-acrylate telechelic oligomer proved to be very resistant to accelerated weathering in the presence of these light stabilizers. The chemical modifications occurring upon QUV-ageing were monitored by infrared spectroscopy, a very sensitive technique well suited for quantitative analysis at an early stage of the photodegradation.

  12. Bond strength of denture teeth to acrylic bases.

    PubMed

    Cunningham, J L

    1993-10-01

    The literature relating to the determination of the bond strength of plastic denture teeth to acrylic resin denture material is reviewed. The papers are presented in chronological order with information on specimen preparation, batch sizes and methods of testing. The lack of uniformity in experimental techniques and the diverse range of products assessed makes recommendations for laboratory practice difficult to formulate. One consistent observation is that tooth surface contamination with wax decreases the bond strength between the teeth and the denture base material. A universal testing method needs to be formulated to replace the various techniques now employed.

  13. Control of contamination of radon-daughters in the DEAP-3600 acrylic vessel

    NASA Astrophysics Data System (ADS)

    Jillings, Chris; DEAP Collaboration

    2013-08-01

    DEAP-3600 is a 3600kg single-phase liquid-argon dark matter detector under construction at SNOLAB with a sensitivity of 10-46cm2 for a 100 GeV WIMP. The argon is held an an acrylic vessel coated with wavelength-shifting 1,1,4,4-tetraphenyl-1,3-butadiene (TPB). Acrylic was chosen because it is optically transparent at the shifted wavelength of 420 nm; an effective neutron shield; and physically strong. With perfect cleaning of the acrylic surface before data taking the irreducible background is that from bulk 210Pb activity that is near the surface. To achieve a background rate of 0.01 events in the 1000-kg fiducial volume per year of exposure, the allowed limit of Pb-210 in the bulk acrylic is 31 mBq/tonne (= 1.2 × 10-20g/g). We discuss how pure acrylic was procured and manufactured into a complete vessel paying particular attention to exposure to radon during all processes. In particular field work at the acrylic panel manufacturer, RPT Asia, and acrylic monomer supplier, Thai MMA Co. Ltd, in Thailand is described. The increased diffusion of radon during annealing the acrylic at 90C as well as techniques to mitigate against this are described.

  14. 40 CFR 721.10397 - Alkyl acrylate-polyfluoro methacrylate-poly(oxyalkylenediyl)-methacrylates (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Alkyl acrylate-polyfluoro methacrylate... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10397 Alkyl acrylate-polyfluoro... subject to reporting. (1) The chemical substances identified generically as alkyl...

  15. 40 CFR 721.10397 - Alkyl acrylate-polyfluoro methacrylate-poly(oxyalkylenediyl)-methacrylates (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Alkyl acrylate-polyfluoro methacrylate... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10397 Alkyl acrylate-polyfluoro... subject to reporting. (1) The chemical substances identified generically as alkyl...

  16. 40 CFR 721.10397 - Alkyl acrylate-polyfluoro methacrylate-poly(oxyalkylenediyl)-methacrylates (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Alkyl acrylate-polyfluoro methacrylate... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10397 Alkyl acrylate-polyfluoro... subject to reporting. (1) The chemical substances identified generically as alkyl...

  17. 40 CFR 721.10530 - Acrylate manufacture byproduct distillation residue (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... distillation residue (generic). 721.10530 Section 721.10530 Protection of Environment ENVIRONMENTAL PROTECTION... New Uses for Specific Chemical Substances § 721.10530 Acrylate manufacture byproduct distillation... substance is identified generically as acrylate manufacture byproduct distillation residue (PMN P-12-87)...

  18. 40 CFR 721.10530 - Acrylate manufacture byproduct distillation residue (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... distillation residue (generic). 721.10530 Section 721.10530 Protection of Environment ENVIRONMENTAL PROTECTION... New Uses for Specific Chemical Substances § 721.10530 Acrylate manufacture byproduct distillation... substance is identified generically as acrylate manufacture byproduct distillation residue (PMN P-12-87)...

  19. 21 CFR 177.1480 - Nitrile rubber modified acrylonitrile-methyl acrylate copolymers.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Nitrile rubber modified acrylonitrile-methyl... Nitrile rubber modified acrylonitrile-methyl acrylate copolymers. Nitrile rubber modified acrylonitrile... rubber modified acrylonitrile-methyl acrylate copolymers consist of basic copolymers produced by...

  20. 21 CFR 177.1480 - Nitrile rubber modified acrylonitrile-methyl acrylate copolymers.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Nitrile rubber modified acrylonitrile-methyl... Nitrile rubber modified acrylonitrile-methyl acrylate copolymers. Nitrile rubber modified acrylonitrile... rubber modified acrylonitrile-methyl acrylate copolymers consist of basic copolymers produced by...

  1. 21 CFR 177.1480 - Nitrile rubber modified acrylonitrile-methyl acrylate copolymers.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Nitrile rubber modified acrylonitrile-methyl... Nitrile rubber modified acrylonitrile-methyl acrylate copolymers. Nitrile rubber modified acrylonitrile... rubber modified acrylonitrile-methyl acrylate copolymers consist of basic copolymers produced by...

  2. 21 CFR 177.1480 - Nitrile rubber modified acrylonitrile-methyl acrylate copolymers.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Nitrile rubber modified acrylonitrile-methyl... Components of Single and Repeated Use Food Contact Surfaces § 177.1480 Nitrile rubber modified acrylonitrile-methyl acrylate copolymers. Nitrile rubber modified acrylonitrile-methyl acrylate copolymers...

  3. 21 CFR 177.1480 - Nitrile rubber modified acrylonitrile-methyl acrylate copolymers.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Nitrile rubber modified acrylonitrile-methyl... Nitrile rubber modified acrylonitrile-methyl acrylate copolymers. Nitrile rubber modified acrylonitrile... rubber modified acrylonitrile-methyl acrylate copolymers consist of basic copolymers produced by...

  4. Preparation and properties of acrylic resin coating modified by functional graphene oxide

    NASA Astrophysics Data System (ADS)

    Dong, Rui; Liu, Lili

    2016-04-01

    To improve the dispersion and the strength of filler-matrix interface in acrylic resin, the functional graphene oxide (FGO) was obtained by surface modification of graphene oxide (GO) by γ-methacryloxypropyl trimethoxysilane (KH-570) and then the acrylic nanocomposites containing different loadings of GO and FGO were prepared. The structure, morphology and dispersion/exfoliation of the FGO were characterized by XRD, FT-IR, Raman, XPS, SEM and TEM. The results demonstrated that the KH-570 was successfully grafted onto the surface of GO sheets. Furthermore, the corresponding thermal, mechanical and chemical resistance properties of the acrylic nanocomposites filled with the FGO were studied and compared with those of neat acrylic and GO/acrylic nanocomposites. The results revealed that the loading of FGO effectively enhanced various properties of acrylic resin. These findings confirmed that the dispersion and interfacial interaction were greatly improved by incorporation of FGO, which might be the result of covalent bonds between the FGO and the acrylic matrix. This work demonstrates an in situ polymerization method to construct a flexible interphase structure, strong interfacial interaction and good dispersion of FGO in acrylic nanocomposites, which can reinforce the polymer properties and be applied in research and industrial areas.

  5. 40 CFR 721.10389 - Styrene, copolymer with acrylic acid, salt with alkoxylated alkenylamine (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Styrene, copolymer with acrylic acid... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10389 Styrene, copolymer with acrylic... subject to reporting. (1) The chemical substance identified generically as styrene, copolymer with...

  6. 40 CFR 721.10389 - Styrene, copolymer with acrylic acid, salt with alkoxylated alkenylamine (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Styrene, copolymer with acrylic acid... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10389 Styrene, copolymer with acrylic... subject to reporting. (1) The chemical substance identified generically as styrene, copolymer with...

  7. Control of contamination of radon-daughters in the DEAP-3600 acrylic vessel

    SciTech Connect

    Jillings, Chris; Collaboration: DEAP Collaboration; and others

    2013-08-08

    DEAP-3600 is a 3600kg single-phase liquid-argon dark matter detector under construction at SNOLAB with a sensitivity of 10{sup −46}cm{sup 2} for a 100 GeV WIMP. The argon is held an an acrylic vessel coated with wavelength-shifting 1,1,4,4-tetraphenyl-1,3-butadiene (TPB). Acrylic was chosen because it is optically transparent at the shifted wavelength of 420 nm; an effective neutron shield; and physically strong. With perfect cleaning of the acrylic surface before data taking the irreducible background is that from bulk {sup 210}Pb activity that is near the surface. To achieve a background rate of 0.01 events in the 1000-kg fiducial volume per year of exposure, the allowed limit of Pb-210 in the bulk acrylic is 31 mBq/tonne (= 1.2 × 10{sup −20}g/g). We discuss how pure acrylic was procured and manufactured into a complete vessel paying particular attention to exposure to radon during all processes. In particular field work at the acrylic panel manufacturer, RPT Asia, and acrylic monomer supplier, Thai MMA Co. Ltd, in Thailand is described. The increased diffusion of radon during annealing the acrylic at 90C as well as techniques to mitigate against this are described.

  8. 40 CFR 721.10389 - Styrene, copolymer with acrylic acid, salt with alkoxylated alkenylamine (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Styrene, copolymer with acrylic acid... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10389 Styrene, copolymer with acrylic... subject to reporting. (1) The chemical substance identified generically as styrene, copolymer with...

  9. Synthesis of Radiation Curable Palm Oil-Based Epoxy Acrylate: NMR and FTIR Spectroscopic Investigations.

    PubMed

    Salih, Ashraf M; Ahmad, Mansor Bin; Ibrahim, Nor Azowa; Dahlan, Khairul Zaman Hj Mohd; Tajau, Rida; Mahmood, Mohd Hilmi; Yunus, Wan Md Zin Wan

    2015-01-01

    Over the past few decades, there has been an increasing demand for bio-based polymers and resins in industrial applications, due to their potential lower cost and environmental impact compared with petroleum-based counterparts. The present research concerns the synthesis of epoxidized palm oil acrylate (EPOLA) from an epoxidized palm oil product (EPOP) as environmentally friendly material. EPOP was acrylated by acrylic acid via a ring opening reaction. The kinetics of the acrylation reaction were monitored throughout the reaction course and the acid value of the reaction mixture reached 10 mg KOH/g after 16 h, indicating the consumption of the acrylic acid. The obtained epoxy acrylate was investigated intensively by means of FTIR and NMR spectroscopy, and the results revealed that the ring opening reaction was completed successfully with an acrylation yield about 82%. The UV free radical polymerization of EPOLA was carried out using two types of photoinitiators. The radiation curing behavior was determined by following the conversion of the acrylate groups. The cross-linking density and the hardness of the cured EPOLA films were measured to evaluate the effect of the photoinitiator on the solid film characteristics, besides, the thermal and mechanical properties were also evaluated. PMID:26248072

  10. The acute aquatic toxicity of a series of acrylate and methacrylate esters

    SciTech Connect

    Staples, C.A.; McLaughlin, J.E.; Hamilton, J.D.

    1994-12-31

    Acute aquatic toxicity data for several acrylate and methacrylate esters were reviewed. Acrylates included acrylic acid, ethyl-, and butyl-acrylate. Methacrylates included methacrylic acid, methyl-, and butyl-methacrylate. Tests were 48 hr or 96 hr standard flow through (invertebrates and fish) assays (measured exposure concentrations). These data are currently used in a risk assessment of acrylate/methacrylate environmental safety. Algal growth (Selanastrum capricomutum) 96 hr EC{sub 50}s were 0.17 mg/L (NOEC < 0.13 mg/L) for acrylic acid, 11.0 mg/L (NOEC < 6.5 mg/L) for ethyl acrylate, and 5.2 mg/L (NOEC < 3.8 mg/L) for butyl acrylate. Invertebrate (Daphnia magna) 48 hr LC{sub 50}s were 95.0 mg/L (NOEC 23.0 mg/L) for acrylic acid, 7.9 mg/L (NOEC 3.4 mg/L) for ethyl acrylate, and 8.2 mg/L (NOEC 2.4 mg/L) for butyl acrylate. Rainbow trout (Oncorhynchus mykiss) 96 hr LC{sub 50}s were 27.0 mg/L (NOEC 6.3 mg/L) for acrylic acid, 4.6 mg/L (NOEC 0.78 mg/L) for ethyl acrylate, and 5.2 mg/L (NOEC 3.8 mg/L) for butyl acrylate. Algae 96 hr EC{sub 50}s were 0.59 mg/L (NOEC 0.38 mg/L) for methacrylic acid, 170.0 mg/L (NOEC 100.0 mg/L) for methyl methacrylate, and 130.0 mg/L for butyl methacrylate. Daphnia magna 48 hr LC{sub 50}s were > 130.0 mg/L (NOEC 130.0 mg/L) for methacrylic acid, 69.0 mg/L (NOEC 48.0 mg/L) for methyl methacrylate, and 32.0 mg/L (NOEC 23.0 mg/L) for butyl methacrylate. Trout 96 hr LC{sub 50}s were 85.0 mg/L (NOEC 12.0 mg/L) for methacrylic acid and > 79.0 mg/L (NOEC 40.0 mg/L) for methyl methacrylate. The fathead minnow (Pimephales promelas) 96 hr LC{sub 50} was 11.0 mg/L for butyl methacrylate.

  11. Effect of Beverages on the Hardness and Tensile Bond Strength of Temporary Acrylic Soft Liners to Acrylic Resin Denture Base

    PubMed Central

    Safari, A; Vojdani, M; Mogharrabi, S; Iraji Nasrabadi, N; Derafshi, R

    2013-01-01

    Statement of Problem: Two potential problems commonly identified with a denture base incorporating a resilient liner are failure of the bond between acrylic resin and soft liner material, and loss of resiliency of the soft liner over time. Since patients may drink different beverages, it is important to evaluate their effects on physical properties of soft lining materials. Purpose: The objective of this in vitro study was to evaluate the effect of different beverages on the hardness of two temporary acrylic-based soft lining materials and their bond strength to the denture base resin. Materials and Method: For the hardness test; a total of 80 rectangular specimens (40mm×10mm×3mm) were fabricated from a heat-polymerized polymethylmethacrylate. Two commercially auto-polymerized acrylic resin-based resilient liners; Coe-Soft and Visco-gel were prepared according to the manufacturers’ instructions and applied on the specimens. For the tensile test, 160 cylindrical specimens (30mm×10mm) were prepared. The liners were added between specimens with a thickness of 3 mm. The specimens of both soft liners were divided into 4 groups (n=10) and immersed in distilled water as the control group, Coca-Cola, 8% and 50% ethanol. All groups were stored in separate containers at 37oC for 12 days. All beverages were changed daily. The hardness was determined using a Shore A durometer and tensile bond strength was determined in a ZwickRoell testing machine at a cross-head speed of 5mm/min. The results were analyzed using two-way ANOVA. Results: There was no significant interaction between the soft liners and the drinks for both hardness (p= 0.748) and bond strength (p= 0.902). There were statistically significant differences between all drinks for both hardness (p< 0.001) and bond strength (p< 0.05). Conclusion: Within the limitations of this study, it seems that drinking Coca-Cola and alcoholic beverages would not be potentially causing any problems for the temporary

  12. Fluoride Release from Hollow Silica Microsphere-Containing Dental Restorative Acrylate Resin.

    PubMed

    Ji, Yuqin; Gao, Jun; Yin, Hengbo; Wang, Aili; Jiang, Tingshun; Wu, Gang; Wu, Zhanao

    2015-05-01

    Hollow silica microspheres with mesoporous shells were prepared by the sacrificial template method. Hollow silica microsphere-containing acrylate resin-based dental restoration materials were prepared by using hollow silica microspheres as NaF reservoirs. Fluoride release performances from naked hollow silica microspheres, acrylate resin, and hollow silica microsphere-containing acrylate resin-based dental restorative materials in an artificial saliva were investigated. The results showed that hollow silica microsphere-containing acrylate resin-based dental restorative materials had higher cumulative fluoride release quantities and sustained fluoride release rates than traditional acrylate resin-based dental restorative materials. Fluoride release could be tuned by changing the mesoporous shell thickness of hollow silica microsphere.

  13. Plasma polymerization of acrylic acid onto polystyrene by cyclonic plasma at atmospheric pressure

    NASA Astrophysics Data System (ADS)

    Chang, Yi-Jan; Lin, Chin-Ho; Huang, Chun

    2016-01-01

    The cyclonic atmospheric-pressure plasma is developed for chamberless deposition of poly(acrylic acid) film from argon/acrylic acid mixtures. The photoemission plasma species in atmospheric-pressure plasma polymerization was identified by optical emission spectroscopy (OES). The OES diagnosis data and deposition results indicated that in glow discharge, the CH and C2 species resulted from low-energy electron-impact dissociation that creates deposition species, but the strong CO emission lines are related to nondeposition species. The acrylic acid flow rate is seen as the key factor affecting the film growth. The film surface analysis results indicate that a smooth, continuous, and uniform surface of poly(acrylic acid) films can be formed at a relatively low plasma power input. This study reveals the potential of chamberless film growth at atmospheric pressure for large-area deposition of poly(acrylic acid) films.

  14. The study of synthesis and photocuring behaviors of organic silicon modified methylacrylate and acrylate

    NASA Astrophysics Data System (ADS)

    Wang, Si-yuan; Zou, Ying-quan

    2012-03-01

    Ten different silicon-containing methyl acrylate and acrylate monomers were synthesized by the substitution reaction of chlorosilanes or chlorosiloxanes with 2-Hydroxyethyl methacrylate or 2-Hydroxyethyl acrylate. Using triethylamine as the catalytic agent, tetrahydrofuran as the solvent, pure products can be obtained with one-step reaction after reduced pressure distillation or column chromatography via controlling raw ratio and reaction time. In this study, one to four silicon contained methyl acrylate and acrylate monomers were synthesized with simple methd and high yield. Monomers' properties were characterized through IR, 1H-NMR, 13C-NMR and their viscosity and thermostability were also characterized. The polymers' have good performance on UV-curing and low surface energy.

  15. Influence of Sea Water Aging on the Mechanical Behaviour of Acrylic Matrix Composites

    NASA Astrophysics Data System (ADS)

    Davies, P.; Le Gac, P.-Y.; Le Gall, M.

    2016-07-01

    A new matrix resin was recently introduced for composite materials, based on acrylic resin chemistry allowing standard room temperature infusion techniques to be used to produce recyclable thermoplastic composites. This is a significant advance, particularly for more environmentally-friendly production of large marine structures such as boats. However, for such applications it is essential to demonstrate that composites produced with these resins resist sea water exposure in service. This paper presents results from a wet aging study of unreinforced acrylic and glass and carbon fibre reinforced acrylic composites. It is shown that the acrylic matrix resin is very stable in seawater, showing lower property losses after seawater aging than those of a commonly-used epoxy matrix resin. Carbon fibre reinforced acrylic also shows good property retention after aging, while reductions in glass fibre reinforced composite strengths suggest that specific glass fibre sizing may be required for optimum durability.

  16. Acrylic Resin Molding Based Head Fixation Technique in Rodents.

    PubMed

    Roh, Mootaek; Lee, Kyungmin; Jang, Il-Sung; Suk, Kyoungho; Lee, Maan-Gee

    2016-01-12

    Head fixation is a technique of immobilizing animal's head by attaching a head-post on the skull for rigid clamping. Traditional head fixation requires surgical attachment of metallic frames on the skull. The attached frames are then clamped to a stationary platform resulting in immobilization of the head. However, metallic frames for head fixation have been technically difficult to design and implement in general laboratory environment. In this study, we provide a novel head fixation method. Using a custom-made head fixation bar, head mounter is constructed during implantation surgery. After the application of acrylic resin for affixing implants such as electrodes and cannula on the skull, additional resins applied on top of that to build a mold matching to the port of the fixation bar. The molded head mounter serves as a guide rails, investigators conveniently fixate the animal's head by inserting the head mounter into the port of the fixation bar. This method could be easily applicable if implantation surgery using dental acrylics is necessary and might be useful for laboratories that cannot easily fabricate CNC machined metal head-posts.

  17. Characteristics and mechanisms of acrylate polymer damage to maize seedlings.

    PubMed

    Chen, Xian; Mao, Xiaoyun; Lu, Qin; Liao, Zongwen; He, Zhenli

    2016-07-01

    Superabsorbent acrylate polymers (SAPs) have been widely used to maintain soil moisture in agricultural management, but they may cause damage to plants, and the mechanisms are not well understood. In this study, seed germination, soil pot culture, hydroponic experiments, and SAPs degradation were conducted to investigate damage characteristics and mechanisms associated with SAPs application. The Results showed that SAPs inhibited maize growth and altered root morphology (irregular and loose arrangement of cells and breakage of cortex parenchyma), and the inhibitory effects were enhanced at higher SAPs rates. After 1h SAP hydrogels treatment, root malondialdehyde (MDA) content was significantly increased, while superoxide dismutase (SOD) and catalase (CAT) content were significantly decreased. Hydroponics experiment indicated that root and shoot growth was inhibited at 2.5mgL(-1) acrylic acid (AA), and the inhibition was enhanced with increasing AA rates. This effect was exacerbated by the presence of Na(+) at a high concentration in the hydrogels. Release and degradation of AA were enhanced at higher soil moisture levels. A complete degradation of AA occurred between 15 and 20 days after incubation (DAI), but it took longer for Na(+) concentration to decrease to a safe level. These results indicate that high concentration of both AA and Na(+) present in the SAPs inhibits plant growth. The finding of this study may provide a guideline for appropriate application of SAPs in agriculture. PMID:27057990

  18. Direct fermentation route for the production of acrylic acid.

    PubMed

    Chu, Hun Su; Ahn, Jin-Ho; Yun, Jiae; Choi, In Suk; Nam, Tae-Wook; Cho, Kwang Myung

    2015-11-01

    There have been growing concerns regarding the limited fossil resources and global climate changes resulting from modern civilization. Currently, finding renewable alternatives to conventional petrochemical processes has become one of the major focus areas of the global chemical industry sector. Since over 4.2 million tons of acrylic acid (AA) is annually employed for the manufacture of various products via petrochemical processes, this chemical has been the target of efforts to replace the petrochemical route by ecofriendly processes. However, there has been limited success in developing an approach combining the biological production of 3-hydroxypropionic acid (3-HP) and its chemical conversion to AA. Here, we report the first direct fermentative route for producing 0.12 g/L of AA from glucose via 3-HP, 3-HP-CoA, and Acryloyl-CoA, leading to a strain of Escherichia coli capable of directly producing acrylic acid. This route was developed through extensive screening of key enzymes and designing a novel metabolic pathway for AA. PMID:26319589

  19. Color difference threshold determination for acrylic denture base resins.

    PubMed

    Ren, Jiabao; Lin, Hong; Huang, Qingmei; Liang, Qifan; Zheng, Gang

    2015-01-01

    This study aimed to set evaluation indicators, i.e., perceptibility and acceptability color difference thresholds, of color stability for acrylic denture base resins for a spectrophotometric assessing method, which offered an alternative to the visual method described in ISO 20795-1:2013. A total of 291 disk specimens 50±1 mm in diameter and 0.5±0.1 mm thick were prepared (ISO 20795-1:2013) and processed through radiation tests in an accelerated aging chamber (ISO 7491:2000) for increasing times of 0 to 42 hours. Color alterations were measured with a spectrophotometer and evaluated using the CIE L*a*b* colorimetric system. Color differences were calculated through the CIEDE2000 color difference formula. Thirty-two dental professionals without color vision deficiencies completed perceptibility and acceptability assessments under controlled conditions in vitro. An S-curve fitting procedure was used to analyze the 50:50% perceptibility and acceptability thresholds. Furthermore, perceptibility and acceptability against the differences of the three color attributes, lightness, chroma, and hue, were also investigated. According to the S-curve fitting procedure, the 50:50% perceptibility threshold was 1.71ΔE00 (r(2)=0.88) and the 50:50% acceptability threshold was 4.00 ΔE00 (r(2)=0.89). Within the limitations of this study, 1.71/4.00 ΔE00 could be used as perceptibility/acceptability thresholds for acrylic denture base resins.

  20. Graft copolymerization of acrylic acid onto polyamide fibers

    NASA Astrophysics Data System (ADS)

    Makhlouf, Chahira; Marais, Stéphane; Roudesli, Sadok

    2007-04-01

    The grafting of acrylic acid (AA) monomer (CH 2dbnd CH sbnd COOH) on polyamide 6.6 monofilaments (PA 6.6) using benzoyl peroxide (BPO) as initiator was carried out in order to enhance the hydrophilic nature of fibers. The grafting rate depends on the AA concentration, the BPO concentration, the time and the temperature of reaction. The best conditions for optimum rate of grafting were obtained with a AA concentration of 0.5 M, a BPO concentration of 0.03 M, a reaction temperature of T = 85 °C and a reaction time of 120 mn. The fiber surface has been investigated by many experimental techniques of characterization such as Fourier transform infrared spectroscopy (FTIR), calorimetric analysis (DSC), scanning electron microscopy (SEM), and contact angle measurements. The effect of grafting of acrylic acid onto PA 6.6 fibers on their moisture and mechanical resistances was analyzed from water sorption and elongation at break measurements. The analysis of the experimental data shows clearly the efficiency of the grafting reaction used, leading to a significant increase of the hydrophilic character of the PA 6.6 surface.

  1. Enzyme-catalyzed synthesis of saccharide acrylate monomers from nonedible biomass.

    PubMed

    Kloosterman, Wouter M J; Brouwer, Sander G M; Loos, Katja

    2014-08-01

    Various cellulase preparations were found to catalyze the transglycosidation between cotton linters and 2-hydroxyethyl acrylate. The conversion and enzyme activity were found to be optimal in reaction mixtures that contained 5 vol % of the acrylate. The structures of the products were revealed by using TLC and (1) H and (13) C NMR spectroscopy. The enzyme-catalyzed reaction resulted in two products. The minor product originated from transglycosidation to hemicellulose and was found to be 2-(β-xylosyloxy)-ethyl acrylate. The major product was identified as 2-(β-glucosyloxy)-ethyl acrylate and the yield of the product was 5 wt % based on the amount of consumed cellulose. Glycosidation products with oligosaccharide moieties could not be detected in the reaction mixture. This result can be explained by the hydrolytic activities of the used cellulase preparation. Cellulase from Trichoderma reesei was found to possess, in addition to endoglucanase activity, cellobiosidase and β-glucosidase activities. Five other cellulase preparations from different origins were tested as well for catalysis of oligosaccharide acrylate synthesis. For most cellulase preparations the major transglycosidation product appeared to be 2-(β-glucosyloxy)-ethyl acrylate. Nevertheless, the endo-β-(1,4)-glucanase from Trichoderma longibrachiatum was found to catalyze the synthesis of 2-(β-cellobiosyloxy)-ethyl acrylate. Unlike the other cellulase preparations, endo-β-(1,4)-glucanase from T. longibrachiatum showed no detectable β-glucosidase activity and therefore oligosaccharide acrylate monomers were not further hydrolyzed into the monosaccharide acrylate 2-(β-glucosyloxy)-ethyl acrylate. PMID:24866837

  2. The reactivity of selected acrylate esters toward glutathione and deoxyribonucleosides in vitro: structure-activity relationships.

    PubMed

    McCarthy, T J; Hayes, E P; Schwartz, C S; Witz, G

    1994-05-01

    Acrylate esters are alpha,beta-unsaturated esters used as plastic monomers whose toxicity may involve reaction with tissue nucleophiles via Michael addition. Structure-activity relationships for reactivity of selected esters with glutathione (GSH) and deoxyribonucleosides were investigated in the present studies. The esters investigated were methyl acrylate, methyl methacrylate, ethyl acrylate, ethyl methacrylate, butyl acrylate, butyl methacrylate, tetraethyleneglycol diacrylate, tetraethyleneglycol dimethacrylate, and ethyleneglycol dimethacrylate. To compare their reactivities toward GSH, esters were incubated for up to 1 hr at 37 degrees C and pH 7.4 with either GSH or red blood cells in phosphate-buffered saline followed by measurement of free thiol. In both systems acrylate electrophilic reactivity decreased with alpha-methyl substitution; however, the decrease in electrophilic reactivity was more evident in the cell-free system than in the red blood cell model. Increased alcohol chain length moderately affected the apparent second-order rate constant for the spontaneous reaction of acrylate esters with GSH, but did not affect potency relative to cellular GSH depletion. The apparent second-order rate constants of bifunctional esters are more than twice the rate constants of the much smaller monofunctional esters. Ethyl acrylate, a reactive acrylate ester based upon glutathione alkylation, has been designated a class 2B (suspect human) carcinogen by the International Agency for Research on Cancer. To detect possible DNA alkylation by acrylate esters in vitro, ethyl acrylate was incubated with deoxyribonucleosides for up to 24 hr at pH 6.7 or 7.4 and 37 degrees C or up to 8 hr and 50 degrees C. HPLC analysis revealed no detectable adduct formation.(ABSTRACT TRUNCATED AT 250 WORDS)

  3. a Fourier Transform Infrared Study of Competing Equilibrium in P-Vinyl Phenol) Blends.

    NASA Astrophysics Data System (ADS)

    Lichkus, Andrew Murray

    In this thesis a Fourier transform infrared (FTIR) spectroscopic study of polymer blends containing poly(p -vinyl phenol) (PVPh) is presented. The characteristics of the intermolecular hydrogen bonding arising from the interaction between the phenolic hydroxyl and carbonyl groups of the different polyacrylates are discussed. The experimental work is focussed primarily on the PVPh with polyacrylate blend systems which include poly(methyl acrylate), poly(ethyl acrylate), poly(n-butyl acrylate), poly(n-pentyl acrylate) and poly(2-ethyl-hexyl acrylate). The infrared bands associated with the intermolecular hydrogen bonding between the phenolic hydroxyl and acrylate carbonyl group are identified. The proportion of hydrogen bonded carbonyl groups in these blends is quantified both as a function of composition and temperature. The effect of the pendant group on the extent of the intermolecular interaction is discussed. The experimental results from this study, including those obtained by other workers, are recast into theoretical phase diagrams via the application of an association model describing binary blends involving hydrogen bonds. The phase diagrams are compared with experimental observations and found to be in broad general agreement. The theoretical predictions of the model with respect to the effect of molecular weight and polymer repeat unit size on the predicted phase behavior is discussed. This study confirms that the phase behavior of polymer blends exhibiting hydrogen bonding can be adequately described by a model employing a competing equilibrium scheme which includes an excess free energy function to account for the specific interactions.

  4. Investigation of fluorinated (Meth)acrylate monomers and macromonomers suitable for a hydroxy-containing acrylate monomer in UV nanoimprinting.

    PubMed

    Ito, Shunya; Kaneko, Shu; Yun, Cheol Min; Kobayashi, Kei; Nakagawa, Masaru

    2014-06-24

    We investigated reactive fluorinated (meth)acrylate monomers and macromonomers that caused segregation at the cured resin surface of a viscous hydroxy-containing monomer, glycerol 1,3-diglycerolate diacrylate (GDD), and decreased the demolding energy in ultraviolet (UV) nanoimprinting with spin-coated films under a condensable alternative chlorofluorocarbon gas atmosphere. The X-ray photoelectron spectroscopy and contact angle measurements used to determine the surface free energy suggested that a nonvolatile silicone-based methacrylate macromonomer with fluorinated alkyl groups segregated at the GDD-based cured resin surface and decreased the surface free energy, while fluorinated acrylate monomers hardly decreased the surface free energy because of their evaporation during the annealing of the spin-coated films. The average demolding energy of GDD-based cured resins with the macromonomer having fluorinated alkyl groups was smaller than that with the macromonomer having hydrocarbon alkyl groups. The fluorinated alkyl groups were responsible for decreasing the demolding energy rather than the polysiloxane main chains. We demonstrated that the GDD-based UV-curable resin with the fluorinated silicone-based macromonomer was suitable for step-and-repeat UV nanoimprinting with a bare silica mold, in addition to silica molds treated by chemical vapor surface modification with trifluoro-1,1,2,2-tetrahydropropyltrimethoxysilane (FAS3) and tridecafluoro-1,1,2,2-tetrahydrooctyltrimethoxysilane (FAS13). PMID:24892792

  5. Skin barrier function in healthy volunteers as assessed by transepidermal water loss and vascular response to hexyl nicotinate: intra- and inter-individual variability.

    PubMed

    Oestmann, E; Lavrijsen, A P; Hermans, J; Ponec, M

    1993-02-01

    This study assesses the variability of two non-invasive methods of measuring stratum corneum barrier function in vivo. Transepidermal water loss (TEWL), and the vascular response to hexyl nicotinate (HN) penetration as determined by laser-Doppler flowmetry, were measured in a group of 21 healthy volunteers. Each time profile of the vascular response to HN penetration was analysed using the following parameters: the baseline cutaneous blood flow, the lag-time between application and initial response (t0), the time between application and maximum response (tmax), the maximum response, and the slope of the curve. TEWL measured on the left volar forearm showed a normal range of 3.9-7.6 g/m2h and a small inter-individual variability [coefficient of variation (CV) 19.4%]. TEWL values at three other forearm sites did not show differences of clinical importance compared with the left volar forearm. The parameters of the vascular response to HN penetration spanned a wider normal range than the TEWL values (CV between 33 and 52%). Repeat measurements after a 1-2 month interval showed highly reproducible individual TEWL values. The mean difference between first and second measurements was only 0.03 g/m2h; the relative difference 0.6%. The intra-individual reproducibility of t0 and tmax. for HN penetration was also high (relative differences of 2.8 and 3.1%, respectively). The other vascular response parameters were less reproducible (relative differences of 6.9-18.6%). We conclude that TEWL and selected parameters of HN penetration, as non-invasive tests of the stratum corneum barrier function, yield reproducible results and are hence useful for investigations assessing the skin barrier function in various disorders.

  6. Methyl-tert-hexyl ether and methyl-tert-octyl ether as gasoline oxygenates: anticipating widespread risks to community water supply wells.

    PubMed

    Snelling, Jeff; Barnett, Mark O; Zhao, Dongye; Arey, J Samuel

    2007-11-01

    The widespread contamination of groundwater resources associated with methyl-tert-butyl ether (MtBE) use has prompted a search for replacement oxygenates in gasoline. Among the alternatives currently under development are higher methyl-tert-alkyl ethers, notably methyl-tert-hexyl ether (MtHxE) and methyl-tert-octyl ether (MtOcE). As was the case with MtBE, the introduction of these ethers into fuel supplies guarantees their migration into groundwater resources. In the present study, a screening-level risk assessment compared predicted well water concentrations of these ethers to concentrations that might cause adverse effects. A physicochemical model which has been successfully applied to the prediction of MtBE concentrations in community water supply wells (CSWs) was used to predict well water concentrations of MtHxE and MtOcE. The results indicate that these ethers are likely to contaminate water supply wells at slightly lower levels than MtBE as a result of migrating from leaking underground fuel tanks to CSWs. Because very little data is available on the physicochemical and environmental properties of MtHxE and MtOcE, estimation methods were employed in conjunction with the model to predict well water concentrations. Model calculations indicated that MtHxE and MtOcE will be present in many CSWs at concentrations approaching the concentrations that have caused widespread public health concern for MtBE. Based on these results and the possibility that MtHxE and MtOcE are potential carcinogens, testing of the toxicological properties of these ethers is recommended before they are used to replace MtBE in gasoline.

  7. Biocontrol of avocado dematophora root rot by antagonistic Pseudomonas fluorescens PCL1606 correlates with the production of 2-hexyl 5-propyl resorcinol.

    PubMed

    Cazorla, Francisco M; Duckett, Simon B; Bergström, Ed T; Noreen, Sadaf; Odijk, Roeland; Lugtenberg, Ben J J; Thomas-Oates, Jane E; Bloemberg, Guido V

    2006-04-01

    A collection of 905 bacterial isolates from the rhizospheres of healthy avocado trees was obtained and screened for antagonistic activity against Dematophora necatrix, the cause of avocado Dematophora root rot (also called white root rot). A set of eight strains was selected on the basis of growth inhibitory activity against D. necatrix and several other important soilborne phytopathogenic fungi. After typing of these strains, they were classified as belonging to Pseudomonas chlororaphis, Pseudomonas fluorescens, and Pseudomonas putida. The eight antagonistic Pseudomonas spp. were analyzed for their secretion of hydrogen cyanide, hydrolytic enzymes, and antifungal metabolites. P. chlororaphis strains produced the antibiotic phenazine-1-carboxylic acid and phenazine-1-carboxamide. Upon testing the biocontrol ability of these strains in a newly developed avocado-D. necatrix test system and in a tomato-F oxysporum test system, it became apparent that P. fluorescens PCL1606 exhibited the highest biocontrol ability. The major antifungal activity produced by strain P. fluorescens PCL1606 did not correspond to any of the major classes of antifungal antibiotics produced by Pseudomonas biocontrol strains. This compound was purified and subsequently identified as 2-hexyl 5-propyl resorcinol (HPR). To study the role of HPR in biocontrol activity, two Tn5 mutants of P. fluorescens PCL1606 impaired in antagonistic activity were selected. These mutants were shown to impair HRP production and showed a decrease in biocontrol activity. As far as we know, this is the first report of a Pseudomonas biocontrol strain that produces HPR in which the production of this compound correlates with its biocontrol activity.

  8. Facile Fabrication of Gradient Surface Based on (meth)acrylate Copolymer Films

    NASA Astrophysics Data System (ADS)

    Zhang, Y.; Yang, H.; Wen, X.-F.; Cheng, J.; Xiong, J.

    2016-08-01

    This paper describes a simple and economic approach for fabrication of surface wettability gradient on poly(butyl acrylate - methyl methacrylate) [P (BA-MMA)] and poly(butyl acrylate - methyl methacrylate - 2-hydroxyethyl methacrylate) [P (BA-MMA-HEMA)] films. The (meth)acrylate copolymer [including P (BA-MMA) and P (BA-MMA-HEMA)] films are hydrolyzed in an aqueous solution of NaOH and the transformation of surface chemical composition is achieved by hydrolysis in NaOH solution. The gradient wetting properties are generated based on different functional groups on the P (BA-MMA) and P (BA-MMA-HEMA) films. The effects of both the surface chemical and surface topography on wetting of the (meth)acrylate copolymer film are discussed. Surface chemical composition along the materials length is determined by XPS, and surface topography properties of the obtained gradient surfaces are analyzed by FESEM and AFM. Water contact angle system (WCAs) results show that the P (BA-MMA-HEMA) films provide a larger slope of the gradient wetting than P (BA-MMA). Moreover, this work demonstrates that the gradient concentration of chemical composition on the poly(meth) acrylate films is owing to the hydrolysis processes of ester group, and the hydrolysis reactions that have negligible influence on the surface morphology of the poly(meth) acrylate films coated on the glass slide. The gradient wettability surfaces may find broad applications in the field of polymer coating due to the compatibility of (meth) acrylate polymer.

  9. Antimicrobial activity of a quaternary ammonium methacryloxy silicate-containing acrylic resin: a randomised clinical trial

    PubMed Central

    Liu, Si-ying; Tonggu, Lige; Niu, Li-na; Gong, Shi-qiang; Fan, Bing; Wang, Liguo; Zhao, Ji-hong; Huang, Cui; Pashley, David H.; Tay, Franklin R.

    2016-01-01

    Quaternary ammonium methacryloxy silicate (QAMS)-containing acrylic resin demonstrated contact-killing antimicrobial ability in vitro after three months of water storage. The objective of the present double-blind randomised clinical trial was to determine the in vivo antimicrobial efficacy of QAMS-containing orthodontic acrylic by using custom-made removable retainers that were worn intraorally by 32 human subjects to create 48-hour multi-species plaque biofilms, using a split-mouth study design. Two control QAMS-free acrylic disks were inserted into the wells on one side of an orthodontic retainer, and two experimental QAMS-containing acrylic disks were inserted into the wells on the other side of the same retainer. After 48 hours, the disks were retrieved and examined for microbial vitality using confocal laser scanning microscopy. No harm to the oral mucosa or systemic health occurred. In the absence of carry-across effect and allocation bias (disks inserted in the left or right side of retainer), significant difference was identified between the percentage kill in the biovolume of QAMS-free control disks (3.73 ± 2.11%) and QAMS-containing experimental disks (33.94 ± 23.88%) retrieved from the subjects (P ≤ 0.001). The results validated that the QAMS-containing acrylic exhibits favourable antimicrobial activity against plaque biofilms in vivo. The QAMS-containing acrylic may also be used for fabricating removable acrylic dentures. PMID:26903314

  10. The photocatalytic enhancement of acrylic and PET solar water disinfection (SODIS) bottles.

    PubMed

    Carey, J M; Perez, T M; Arsiaga, E G; Loetscher, L H; Boyd, J E

    2011-01-01

    The solar water disinfection method (SODIS) was modified by the addition of a photocatalytic layer of titania on the interior surface of polyethylene terephthalate (PET) and acrylic bottles. Titania was solvent deposited on the interior of commercially available PET bottles, as well as bottles that were constructed from acrylic. Uncoated and titania-coated acrylic bottles removed 3,000,000-5,000,000 colony forming units per milliliter of K12 E. coli from 670 mL of contaminated water in 40 min of solar irradiance. After five hours of sunlight exposure, the concentration of 10 ppm methyl orange (a representative organic water contaminant), was reduced by 61% using the titania-coated acrylic bottles. The concentration of 87 ppb microcystin-LR (a representative algal toxin) was reduced by 70% after 7 hours of sunlight exposure in the titania-coated acrylic bottles. Acrylic is an effective alternative to PET for use in the SODIS method due to its greater UV transparency. The addition of titania to PET and acrylic bottles confers the ability to remove chemical contaminants in addition to inactivating microbiological contaminants.

  11. Effect of thermal cycling and disinfection on microhardness of acrylic resin denture base.

    PubMed

    Goiato, Marcelo Coelho; Dos Santos, Daniela Micheline; Baptista, Gabriella Trunckle; Moreno, Amália; Andreotti, Agda Marobo; Dekon, Stéfan Fiuza de Carvalho

    2013-04-01

    The purpose of this study was to investigate the effect of thermal cycling and disinfection on the microhardness of acrylic resins denture base. Four different brands of acrylic resins were evaluated: Onda Cryl, QC 20, Classico and Lucitone. Each brand of acrylic resin was divided into four groups (n = 7) according to the disinfection method (microwave, Efferdent, 4% chlorhexidine and 1% hypochlorite). Samples were disinfected during 60 days. Before and after disinfection, samples were thermal cycled between 5-55 °C with 30-s dwell times for 1000 cycles. The microhardness was measured using a microhardener, at baseline (B), after first thermal cycling (T1), after disinfection (D) and after second thermal cycling (T2). The microhardness values of all groups reduced over time. QC-20 acrylic resin exhibited the lowest microhardness values. At B and T1 periods, the acrylic resins exhibited statistically greater microhardness values when compared to D and T2 periods. It can be concluded that the microhardness values of the acrylic resins denture base were affected by the thermal cycling and disinfection procedures. However, all microhardness values obtained herein are within acceptable clinical limits for the acrylic resins.

  12. An ORMOSIL-containing orthodontic acrylic resin with concomitant improvements in antimicrobial and fracture toughness properties.

    PubMed

    Gong, Shi-qiang; Epasinghe, Jeevani; Rueggeberg, Frederick A; Niu, Li-na; Mettenberg, Donald; Yiu, Cynthia K Y; Blizzard, John D; Wu, Christine D; Mao, Jing; Drisko, Connie L; Pashley, David H; Tay, Franklin R

    2012-01-01

    Global increase in patients seeking orthodontic treatment creates a demand for the use of acrylic resins in removable appliances and retainers. Orthodontic removable appliance wearers have a higher risk of oral infections that are caused by the formation of bacterial and fungal biofilms on the appliance surface. Here, we present the synthetic route for an antibacterial and antifungal organically-modified silicate (ORMOSIL) that has multiple methacryloloxy functionalities attached to a siloxane backbone (quaternary ammonium methacryloxy silicate, or QAMS). By dissolving the water-insoluble, rubbery ORMOSIL in methyl methacrylate, QAMS may be copolymerized with polymethyl methacrylate, and covalently incorporated in the pressure-processed acrylic resin. The latter demonstrated a predominantly contact-killing effect on Streptococcus mutans ATCC 36558 and Actinomyces naselundii ATCC 12104 biofilms, while inhibiting adhesion of Candida albicans ATCC 90028 on the acrylic surface. Apart from its favorable antimicrobial activities, QAMS-containing acrylic resins exhibited decreased water wettability and improved toughness, without adversely affecting the flexural strength and modulus, water sorption and solubility, when compared with QAMS-free acrylic resin. The covalently bound, antimicrobial orthodontic acrylic resin with improved toughness represents advancement over other experimental antimicrobial acrylic resin formulations, in its potential to simultaneously prevent oral infections during appliance wear, and improve the fracture resistance of those appliances.

  13. An ORMOSIL-Containing Orthodontic Acrylic Resin with Concomitant Improvements in Antimicrobial and Fracture Toughness Properties

    PubMed Central

    Rueggeberg, Frederick A.; Niu, Li-na; Mettenberg, Donald; Yiu, Cynthia K. Y.; Blizzard, John D.; Wu, Christine D.; Mao, Jing; Drisko, Connie L.; Pashley, David H.; Tay, Franklin R.

    2012-01-01

    Global increase in patients seeking orthodontic treatment creates a demand for the use of acrylic resins in removable appliances and retainers. Orthodontic removable appliance wearers have a higher risk of oral infections that are caused by the formation of bacterial and fungal biofilms on the appliance surface. Here, we present the synthetic route for an antibacterial and antifungal organically-modified silicate (ORMOSIL) that has multiple methacryloloxy functionalities attached to a siloxane backbone (quaternary ammonium methacryloxy silicate, or QAMS). By dissolving the water-insoluble, rubbery ORMOSIL in methyl methacrylate, QAMS may be copolymerized with polymethyl methacrylate, and covalently incorporated in the pressure-processed acrylic resin. The latter demonstrated a predominantly contact-killing effect on Streptococcus mutans ATCC 36558 and Actinomyces naselundii ATCC 12104 biofilms, while inhibiting adhesion of Candida albicans ATCC 90028 on the acrylic surface. Apart from its favorable antimicrobial activities, QAMS-containing acrylic resins exhibited decreased water wettability and improved toughness, without adversely affecting the flexural strength and modulus, water sorption and solubility, when compared with QAMS-free acrylic resin. The covalently bound, antimicrobial orthodontic acrylic resin with improved toughness represents advancement over other experimental antimicrobial acrylic resin formulations, in its potential to simultaneously prevent oral infections during appliance wear, and improve the fracture resistance of those appliances. PMID:22870322

  14. Base-Mediated Stereospecific Synthesis of Aryloxy and Amino substituted Ethyl Acrylates

    PubMed Central

    Namjoshi, Ojas A.; Verma, Ranjit; Lorenz, Michael; Tiruveedhula, V. V. N. Phani Babu; Monte, Aaron; Bertz, Steven H.

    2011-01-01

    The stereospecific synthesis of aryloxy and amino substituted E- and Z-ethyl-3-acrylates is of interest because of their potential in the polymer industry and in medicinal chemistry. During work on a copper-catalyzed cross-coupling reaction of E- and Z-ethyl-3-iodo-acrylates with phenols and N-heterocycles, we discovered a very simple (non-metallic) method for the stereospecific synthesis of aryloxy and amino substituted acrylates. To study this long standing problem on the stereoselectivity of aryloxy and amino substituted acrylates, a series of O- and N-substituted nucleophiles was allowed to react with E- and Z-ethyl-3-iodo-acrylates. Screening of different bases indicated that DABCO (1,4-diazabicyclo[2.2.2]octane) afforded successful conversion of E- and Z- ethyl-3-iodoacrylates into aryloxy and amino substituted ethyl acrylates in a stereospecific manner. Herein are the details of this DABCO-mediated stereospecific synthesis of aryloxy and amino substituted E- or Z-acrylates. PMID:22073965

  15. Antimicrobial activity of a quaternary ammonium methacryloxy silicate-containing acrylic resin: a randomised clinical trial.

    PubMed

    Liu, Si-ying; Tonggu, Lige; Niu, Li-na; Gong, Shi-qiang; Fan, Bing; Wang, Liguo; Zhao, Ji-hong; Huang, Cui; Pashley, David H; Tay, Franklin R

    2016-02-23

    Quaternary ammonium methacryloxy silicate (QAMS)-containing acrylic resin demonstrated contact-killing antimicrobial ability in vitro after three months of water storage. The objective of the present double-blind randomised clinical trial was to determine the in vivo antimicrobial efficacy of QAMS-containing orthodontic acrylic by using custom-made removable retainers that were worn intraorally by 32 human subjects to create 48-hour multi-species plaque biofilms, using a split-mouth study design. Two control QAMS-free acrylic disks were inserted into the wells on one side of an orthodontic retainer, and two experimental QAMS-containing acrylic disks were inserted into the wells on the other side of the same retainer. After 48 hours, the disks were retrieved and examined for microbial vitality using confocal laser scanning microscopy. No harm to the oral mucosa or systemic health occurred. In the absence of carry-across effect and allocation bias (disks inserted in the left or right side of retainer), significant difference was identified between the percentage kill in the biovolume of QAMS-free control disks (3.73 ± 2.11%) and QAMS-containing experimental disks (33.94 ± 23.88%) retrieved from the subjects (P ≤ 0.001). The results validated that the QAMS-containing acrylic exhibits favourable antimicrobial activity against plaque biofilms in vivo. The QAMS-containing acrylic may also be used for fabricating removable acrylic dentures.

  16. Gel polymer electrolytes based on nanofibrous polyacrylonitrile–acrylate for lithium batteries

    SciTech Connect

    Kim, Dul-Sun; Woo, Jang Chang; Youk, Ji Ho; Manuel, James; Ahn, Jou-Hyeon

    2014-10-15

    Graphical abstract: - Highlights: • Nanofibrous polyacrylonitrile–acrylate membranes were prepared by electrospinning. • Trimethylolpropane triacrylate was used as a crosslinking agent of fibers. • The GPE based on PAN–acrylate (1/0.5) showed good electrochemical properties. - Abstract: Nanofibrous membranes for gel polymer electrolytes (GPEs) were prepared by electrospinning a mixture of polyacrylonitrile (PAN) and trimethylolpropane triacrylate (TMPTA) at weight ratios of 1/0.5 and 1/1. TMPTA is used to achieve crosslinking of fibers thereby improving mechanical strength. The average fiber diameters increased with increasing TMPTA concentration and the mechanical strength was also improved due to the enhanced crosslinking of fibers. GPEs based on electrospun membranes were prepared by soaking them in a liquid electrolyte of 1 M LiPF{sub 6} in ethylene carbonate (EC)/dimethyl carbonate (DMC) (1:1, v/v). The electrolyte uptake and ionic conductivity of GPEs based on PAN and PAN–acrylate (weight ratio; 1/1 and 1/0.5) were investigated. Ionic conductivity of GPEs based on PAN–acrylate was the highest for PAN/acrylate (1/0.5) due to the proper swelling of fibers and good affinity with liquid electrolyte. Both GPEs based on PAN and PAN–acrylate membranes show good oxidation stability, >5.0 V vs. Li/Li{sup +}. Cells with GPEs based on PAN–acrylate (1/0.5) showed remarkable cycle performance with high initial discharge capacity and low capacity fading.

  17. Flexural Strength of Cold and Heat Cure Acrylic Resins Reinforced with Different Materials

    PubMed Central

    Heidari, Bijan; Firouz, Farnaz; Izadi, Alireza; Ahmadvand, Shahbaz

    2015-01-01

    Objectives: Heat-polymerized acrylic resin has been the most commonly used denture base material for over 60 years. However, the mechanical strength of acrylic resin is not adequate for long-term clinical performance of dentures. Consequently, fracture is a common clinical occurrence, which often develops in the midline of the denture base. This study aimed to evaluate the efficacy of cold-cure and heat-cure acrylic resins, reinforced with glass fibers, polyethylene fibers, and metal wire for denture base repair. Materials and Methods: Ninety specimens were prepared and allocated to nine groups. Ten specimens were considered as controls, and 80 were divided into 8 experimental groups. In the experimental groups, the specimens were sectioned into two halves from the middle, and were then divided into two main groups: one group was repaired with heat cure acrylic resin, and the other with cold cure acrylic resin. Each group was divided into 4 subgroups: unreinforced, reinforced with glass fibers, polyethylene fibers, and metal wire. All specimens were subjected to a 3-point bending test, and the flexural strength was calculated. Results: The group repaired with heat cure acrylic resin and reinforced with glass fiber showed the highest flexural strength; however, the group repaired with cold cure acrylic resin and reinforced with polyethylene fibers had the lowest flexural strength. There was no significant difference between the groups repaired with heat cure and cold cure acrylic resins without reinforcement. Conclusion: Repairing denture base with heat cure acrylic resin, reinforced with glass fibers increases the flexural strength of denture base. PMID:26877726

  18. [Acrylic resin reinforcement with metallic and nonmetallic inserts].

    PubMed

    Preoteasa, Elena; Murariu, Cătălina Măgureanu; Ionescu, Ecaterina; Preoteasa, Cristina Teodora

    2007-01-01

    In the current use of acrylic resin for removable dentures and orthodontic treatments we are frequently facing the fact of base fracture. The repairing of this, determine most of the time, discomfort of the patient, by excluding the prosthetic device, affecting the treatment, loosing patient's time, doctor's time, implying the dental laboratory and extra expenses. The causes of fractures are many, from clinical cases with some specific anatomic and functional particularities, or parafunctional, to the incorrect designing, manufacturing or wearing of the prosthetic part, being connected with the materials characteristics. The consequences and costs of these fractures are leading to unsatisfying results in some of the clinical cases, in presence of parafunctions like bruxism or clenching and specifically for the new types of prosthetic rehabilitation, on natural teeth or implants. PMID:17983190

  19. Chain Transfer of Vegetable Oil Macromonomers in Acrylic Solution Copolymerization

    SciTech Connect

    Black, Micah; Messman, Jamie M; Rawlins, James

    2011-01-01

    Use of vegetable oil macromonomers (VOMMs) as comonomers in emulsion polymerization enables good film coalescence without the addition of solvents that constitute volatile organic compounds (VOCs). VOMMs are derived from renewable resources and offer the potential of post-application crosslinking via auto-oxidation. However, chain transfer reactions of VOMMs with initiator and/or polymer radicals during emulsion polymerization reduce the amount of allylic hydrogen atoms available for primary auto-oxidation during drying. Vegetable oils and derivatives were reacted in combination with butyl acrylate and methyl methacrylate via solution polymerization. The copolymerization was monitored using in situ infrared spectroscopy to determine the extent of chain transfer. 1H NMR spectroscopy was used to determine the loci of chain transfer and the molecular weight characteristics of the polymers were characterized by SEC. Solution polymerization was utilized to minimize temperature fluctuations and maintain polymer solubility during the initial characterization.

  20. Laboratory analyses of two explanted hydrophobic acrylic intraocular lenses

    PubMed Central

    Dai, Yunhai; Huang, Yusen; Liu, Ting; Xie, Lixin

    2014-01-01

    Two three-piece hydrophobic acrylic intraocular lenses (IOLs) were explanted from two patients at 7 and 9 years, respectively, after implantation, because of poor fundus visualisation and/or a clinically significant decrease in visual acuity related to their opacified IOLs. In addition to light microscopy, scanning electron microscopy and energy dispersive X-ray spectroscopy, confocal laser scanning microscopy was used for the first time to observe the explanted IOLs. The clinical aspect seemed to correspond to the phenomenon of surface light scattering, while laboratory analyses showed dense glistenings in the central layer of the IOL optic, which had no change next to the surface. Further studies on these phenomena are needed. PMID:25005210

  1. Spectral filters based on ethylene/acrylic acid copolymer ionomers

    SciTech Connect

    Riley, M.O.; Walkup, C.M.; Hagen, W.F.; Jessop, E.S.

    1988-09-01

    We are investigating the possibility of utilizing ionomers as inexpensive, easily replaced optical filters for applications in large fusion lasers as well as high average power solid state lasers. To this end we have synthesized a number of other derivatives of the ethylene/acrylic acid (EAA) copolymer system. Specifically, we prepared several ionomers at nominal 3 wt. % metal ion concentration, including Fe(III), Co(II), Ni(II), Cu(II), and Ce(III), by reacting aqueous solutions of metal acetates or nitrates with aqueous ammonia dispersions (1) of EAA as described previously. The products were compression molded into thin optically clear films under the above-described conditions. A gel was formed in a similar reaction with samarium (III) nitrate. Accordingly, the samarium ionomer was synthesized by a melt phase reaction between the EAA resin and the metal nitrate. 6 refs., 2 figs., 2 tabs.

  2. Cerenkov Light Collection With an Acrylic Wavelength Shifting Plate

    NASA Astrophysics Data System (ADS)

    Carl, Michael; Reinhold, Joerg

    2003-04-01

    Collection of Cerenkov light with an acrylic wavelength shifting plate was investigated. The test setup consisted of a plate, 30cm long, 10cm wide, and 1 cm thick placed behind a 5 cm deep stack of aerogel tiles. On the long ends the wavelength shifter was read out by two 5 inch photomultipliers. The response of the system to pions and protons at 1.2 GeV/c momentum was measured at the KEK PS facility in Japan. On average 6 photoelectrons radiated from the aerogel could be detected. The results will be presented and possible designs for future detectors will be discussed with emphasis on particle identification for high momentum spectrometers at an upgraded Jefferson Lab facility.

  3. Swelling behaviors of porous lignin based poly (acrylic acid).

    PubMed

    Ma, Yanli; Sun, Yajie; Fu, Yujie; Fang, Guizhen; Yan, Xingru; Guo, Zhanhu

    2016-11-01

    Supramolecular cross-linked porous lignin based poly (acrylic acid) [LBPAA] was lab-synthesized by copolymerizing lignin grafted N, N'-methylene-bisacrylamide (LM) and acrylic acid. LBPAA successfully acted as a water retention agent with salt resistance and biodegradation for agricultural applications. Lignin was found to improve its swelling behaviors with higher water retention, fast swelling and de-swelling rates. The salt tolerance was stronger in the case of LBPAA (60 PAA/40 LM) [60 wt% PAA/40 wt% LM], i.e., 145.79 g·g(-1) higher than PAA at 0.09 mM KCl solution. The effect of ion charges on the LBPAA swelling ratio was greater than that of ionic radius. The weight loss of LBPAA (60 PAA/40 LM) was 5.47%, 4.96%, and 4.56% in the soil of Tangshan, Harbin, and Sian, respectively. The soil moisture content and clay content were observed to decrease gradually with increasing the burial time. The biodegradation test of LBPAA (60 PAA/40 LM) composite exhibited different bacterial colony forming units (CFU), the soil of Tangshan was 2.0 × 10(3) CFU·g(-1) soil, 7.0 × 10(3) CFU·g(-1) soil for Harbin, and 6.10 × 10(4) CFU·g(-1) soil for Sian. However, the organic matter contents in the soils did not have significant changes (Tangshan 6.21 mg·g(-1), Harbin 0.61 mg·g(-1), and Sian 0.405 mg·g(-1)). PMID:27587327

  4. Radiation-induced grafting of acrylic acid onto polyethylene filaments

    NASA Astrophysics Data System (ADS)

    Kaji, K.; Okada, T.; Sakurada, I.

    Radiation-induced grafting of acrylic acid onto high density polyethylene (PE) filaments was carried out in order to raise softening temperature and impart flame retardance and hydrophilic properties. Mutual γ-irradiation method was employed for the grafting in a mixture of acrylic acid (AA), ethylene dichloride and water containing a small amount of ferrous ammonium sulfate. The rate of grafting was very low at room temperature. On the other hand, large percent grafts were obtained when the grafting was performed at an elevated temperature. Activation energy for the initial rate of grafting was found to be 17 {kcal}/{mol} between 20 and 60°C and 10 {kcal}/{mol} between 60 and 80°C. Original PE filament begins to shrink at 70°C, show maximum shrinkage of 50% at 130°C and then breaks off at 136°C. When a 34% AA graft is converted to metallic salt such as sodium and calcium, the graft filament retains its filament form even above 300°C and gives maximum shrinkage of 15%. Burning tests by a wire-netting basket method indicate that graft filaments and its metallic salts do not form melting drops upon burning and are self-extinguishing. Original PE filament shows no moisture absorption, however, that of AA-grafted PE increases with increasing graft percent. The sodium salt of 15% graft shows the same level of moisture regain as cotton. The AA-grafted PE filament and its metallic salts can be dyed with cationic dyes even at 1% graft. Tensile properties of PE filament is impaired neither by grafting nor by conversion to metallic salts.

  5. The rising trend in allergic contact dermatitis to acrylic nail products.

    PubMed

    Le, Quynh; Cahill, Jennifer; Palmer-Le, Amanda; Nixon, Rosemary

    2015-08-01

    Shellac is a newly available type of long-wearing nail polish, which is becoming increasingly popular. We describe four cases of allergic contact dermatitis (ACD) to acrylates found in Shellac nail products, involving three beauticians and one consumer who purchased the product over the internet. Increasing use of these new acrylic nail products means that dermatologists need to be aware of the possibility of ACD occurring. Testing with hydroxyethyl methacrylate alone, which is included in the Australian Baseline Series, is adequate for screening for acrylate allergy. PMID:25752641

  6. Impression techniques for multiple implants: a photoelastic analysis. Part II: comparison of four acrylic resins.

    PubMed

    Lopes-Júnior, Itamar; de Lima Lucas, Barbara; Gomide, Henner Alberto; Gomes, Vanderlei Luiz

    2013-10-01

    Four commercial brands of chemically activated acrylic resin were compared through photoelastic analysis. Photoelastic resin blocks were made with 2 implants placed parallel to each other and 2 square transfer copings splinted. Both transfers were splinted with chemically activated acrylic resin: Dencrilay, Duralay I, Duralay II, and GC. Data were analyzed by 2-way analysis of variance and Tukey test (P < .05). Statistically significant differences were found among the 3 brands of chemically activated acrylic resin. Dencrilay showed greater dimensional alteration. Duralay I and GC are recommended for the transfer of the position of the multi-implants.

  7. Measuring the mutual diffusion coefficient for dodecyl acrylate in low molecular weight poly(dodecyl acrylate) with laser line deflection (Wiener's Method) and the fluorescence of pyrene.

    PubMed

    Antrim, Daniel; Bunton, Patrick; Lewis, Lydia Lee; Zoltowski, Brian D; Pojman, John A

    2005-06-16

    Diffusion of small molecules into glassy polymers is quite complicated and almost always non-Fickian. Little work has been done with the diffusion of low molecular weight polymers that are liquids at room temperature (such as poly(dodecyl acrylate)) into their miscible monomers. We have studied three molecular weights under 20 000 to determine if poly(dodecyl acrylate) diffusion into dodecyl acrylate could be treated with Fick's law and if so to determine the values of the diffusion coefficients. We compare two methods for measuring the diffusion of dodecyl acrylate into poly(dodecyl acrylate): We used laser line deflection (Wiener's method) and improved upon the method from published reports. We also used the dependence of pyrene's fluorescence on the viscosity to measure the concentration distribution, and thus to extract the diffusion coefficient. After an initial relaxation period, diffusion in all cases followed Fick's law with a single concentration-independent diffusion coefficient. Comparison of the diffusion coefficients obtained by both methods yielded the same order of magnitude for the diffusion coefficients (10(-7) cm2/s) and showed the same trend in the dependence on the average molecular weight of the polymer (a decrease in the diffusion coefficient with an increase in the molecular weight).

  8. Experimental and theoretical charge-density analysis of 1,4-bis(5-hexyl-2-thienyl)butane-1,4-dione: applications of a virtual-atom model.

    PubMed

    Ahmed, Maqsood; Nassour, Ayoub; Noureen, Sajida; Lecomte, Claude; Jelsch, Christian

    2016-02-01

    The experimental and theoretical charge densities of 1,4-bis(5-hexyl-2-thienyl)butane-1,4-dione, a precursor in the synthesis of thiophene-based semiconductors and organic solar cells, are presented. A dummy bond charges spherical atom model is applied besides the multipolar atom model. The results show that the dummy bond charges model is accurate enough to calculate electrostatic-derived properties which are comparable with those obtained by the multipolar atom model. The refinement statistics and the residual electron density values are found to be intermediate between the independent atom and the multipolar formalisms.

  9. Thermodynamic Properties at Saturation Derived from Experimental Two-Phase Isochoric Heat Capacity of 1-Hexyl-3-methylimidazolium bis[(trifluoromethyl)sulfonyl]imide

    NASA Astrophysics Data System (ADS)

    Polikhronidi, Nikolai G.; Batyrova, Rabiyat G.; Abdulagatov, Ilmutdin M.; Magee, Joseph W.; Wu, Jiangtao

    2016-11-01

    New measurements are reported for the isochoric heat capacity of the ionic liquid substance 1-hexyl-3-methylimidazolium bis[(trifluoromethyl)sulfonyl]imide ([C6mim][NTf2]). These measurements extend the ranges of our earlier study (Polikhronidi et al. in Phys Chem Liq 52:657, 2014) by 5 % of the compressed liquid density and by 75 K. An adiabatic calorimeter was used to measure one-phase (C_{V1}) liquid and two-phase (C_{V2}) liquid + vapor isochoric heat capacities, densities (ρ _s), and phase-transition temperatures (T_s) of the ionic liquid (IL) substance. The combined expanded uncertainty of the density ρ and isochoric heat capacity C_V measurements at the 95 % confidence level with a coverage factor of k = 2 is estimated to be 0.15 % and 3 %, respectively. Measurements are concentrated in the immediate vicinity of the liquid + vapor phase-transition curve, in order to closely observe phase transitions. The present measurements and those of our earlier study are analyzed together and are presented in terms of thermodynamic properties (T_s, ρ _s, C_{V1} and C_{V2}) evaluated at saturation and in terms of key-derived thermodynamic properties C_P, C_S, W_S^' }}, K_{TS}^' }}, ( {partial P/partial T} ) V^' }, and ( {partial V/partial T} ) _{P}^' }) on the liquid + vapor phase-transition curve. A thermodynamic relation by Yang and Yang is used to confirm the internal consistency of measured two-phase heat capacities C_{V2} , which are observed to fall perfectly on a line as a function of specific volume at a constant temperature. The observed linear behavior is exploited to evaluate contributions to the quantity C_{V2} = f(V, T) from chemical potential C_{{Vμ}} =-Td^{{2}}μ /dT2 and from vapor pressure C_{VP} =VTd2PS /dT2. The physical nature and specific details of the temperature and specific volume dependence of the two-phase isochoric heat capacity and some features of the other derived thermodynamic properties of IL at liquid saturation curve are considered

  10. Ionic association and solvation of the ionic liquid 1-hexyl-3-methylimidazolium chloride in molecular solvents revealed by vapor pressure osmometry, conductometry, volumetry, and acoustic measurements.

    PubMed

    Sadeghi, Rahmat; Ebrahimi, Nosaibah

    2011-11-17

    A systematic study of osmotic coefficient, conductivity, volumetric and acoustic properties of solutions of ionic liquid 1-hexyl-3-methylimidazolium chloride ([C(6)mim][Cl]) in various molecular solvents has been made at different temperatures in order to study of ionic association and solvation behavior of [C(6)mim][Cl] in different solutions. Precise measurements on electrical conductances of solutions of [C(6)mim][Cl] in water, methanol, ethanol, 1-propanol, 2-propanol, 1-butanol, and acetonitrile at 293.15, 298.15, and 303.15 K are reported and analyzed with Barthel's low-concentration chemical model (lcCM) to obtain the limiting molar conductivities and association constants of this ionic liquid in the investigated solvents. Strong ion pairing was found for the ionic liquid in 2-propanol, 1-butanol, and 1-propanol, whereas ion association in acetonitrile, methanol and ethanol is rather weak and in water the ionic liquid is fully dissociated. In the second part of this work, the apparent molar volumes and isentropic compressibilities of [C(6)mim][Cl] in water, methanol, ethanol, acetonitrile, 1-propanol, 2-propanol, and 1-butanol are obtained at the 288.15-313.15 K temperature range at 5 K intervals at atmospheric pressure from the precise measurements of density and sound velocity. The infinite dilution apparent molar volume and isentropic compressibility values of the free ions and ion pairs of [C(6)mim][Cl] in the investigated solvents as well as the excess molar volume of the investigated solutions are determined and their variations with temperature and type of solvents are also studied. Finally, the experimental measurements of osmotic coefficient at 318.15 K for binary solutions of [C(6)mim][Cl] in water, methanol, ethanol, 2-propanol, and acetonitrile are taken using the vapor pressure osmometry (VPO) method and from which the values of the solvent activity, vapor pressure, activity coefficients, and Gibbs free energies are calculated. The results are

  11. Diethyl hexyl phthalate-induced changes in insulin signaling molecules and the protective role of antioxidant vitamins in gastrocnemius muscle of adult male rat

    SciTech Connect

    Srinivasan, Chinnapaiyan; Khan, Adam Ismail; Balaji, Venkataraman; Selvaraj, Jayaraman; Balasubramanian, Karundevi

    2011-12-15

    Diethyl hexyl phthalate (DEHP) is an endocrine disruptor, it influences various organ systems in human beings and experimental animals. DEHP reduced the serum testosterone and increased the blood glucose, estradiol, T{sub 3} and T{sub 4} in rats. However, the effect of DEHP on insulin signaling and glucose oxidation in skeletal muscle is not known. Adult male albino rats were divided into four groups: Group I: Control; Groups II and III: DEHP treated (dissolved in olive oil at a dose of 10 and 100 mg/kg body weight, respectively, once daily through gastric intubation for 30 days); and Group IV: DEHP (100 mg/kg body weight) plus vitamins E (50 mg/kg body weight) and C (100 mg/kg body weight) dissolved in olive oil and distilled water, respectively, once daily through gastric intubation for 30 days. On completion of treatment, animals were euthanized and perfused (whole body); gastrocnemius muscle was dissected out and subjected to assessment of various parameters. DEHP treatment increased the H{sub 2}O{sub 2}, hydroxyl radical levels and lipid peroxidation which disrupt the membrane integrity and insulin receptor. DEHP impaired the insulin signal transduction, glucose uptake and oxidation through decreased expression of plasma membrane GLUT4, which may partly be responsible for the elevation of fasting blood glucose level. The present study suggests that DEHP exposure affects glucose oxidation in skeletal muscle and is mediated through enhanced lipid peroxidation, impaired insulin signaling and GLUT4 expression in plasma membrane. Antioxidant vitamins (C and E) have a protective role against the adverse effect of DEHP. -- Highlights: Black-Right-Pointing-Pointer DEHP treatment significantly decreased serum insulin and testosterone levels. Black-Right-Pointing-Pointer Increased ROS and decreased glucose uptake were observed in DEHP treated animals. Black-Right-Pointing-Pointer Impaired insulin signaling in gastrocnemius muscle was observed in DEHP treatment. Black

  12. Synthesis and characterization of amylose grafted poly(acrylic acid) and its application in ammonia adsorption.

    PubMed

    Chen, Qing; Yu, Haojie; Wang, Li; Abdin, Zain-Ul; Yang, Xinpeng; Wang, Junhua; Zhou, Weidong; Zhang, Hongtao; Chen, Xiao

    2016-11-20

    Amylose grafted poly(acrylic acid) (Am-g-PAA) was synthesized by graft copolymerization of amylose with acrylic acid. The structure of Am-g-PAA was confirmed by (1)H NMR and FT-IR spectra. The morphology, crystallinity and thermal properties of amylose and Am-g-PAA were investigated by SEM, XRD and TGA, respectively. The highest degree of substitution (DS) of carboxyl group was 1.96 which was obtained after reacted for 1h at 60°C. Acrylic acid to anhydroglucose mole ratio for DS was 19.81. It was found that a large number of carboxyl groups were grafted on the backbone of amylose. It was also found that ammonia adsorption capacity of amylose increased by grafting poly(acrylic acid) on the backbone of amylose. PMID:27561514

  13. Dielectric studies of alkyl acrylates with primary alcohols using time domain reflectometry

    NASA Astrophysics Data System (ADS)

    Dharmalingam, K.; Ramachandran, K.; Sivagurunathan, P.; Prabhakar Undre, B.; Khirade, P. W.; Mehrotra, S. C.

    Binary polar-polar liquid mixtures of alkyl acrylates (methyl acrylate, ethyl acrylate and butyl acrylate) with primary alcohols (propan-1-ol, butan-1-ol and hexan-1-ol) were subjected to dielectric studies at 303 K for different concentrations using time domain reflectometry (TDR) over the frequency range from 10 MHz to 10 GHz. Static permittivity (ɛ0) dielectric constant at high frequency (ɛ∞) and relaxation time (τ) were found through dielectric measurements for different concentrations of each system. The Bruggeman dielectric factor, Kirkwood correlation factor and the excess inverse relaxation time were determined and discussed to yield information on the molecular interactions of the systems. Deviations from the linearity of various models suggest molecular association through hydrogen bonding between the -OH group of alcohols and C=O group of esters. The results also show a dependence of dielectric parameters on the alkyl chain length of both the alcohols and esters.

  14. Biobased composites from thermoplastic polyurethane elastomer and cross-linked acrylated-epoxidized soybean oil

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Soybean oil is an important sustainable material. Crosslinked acrylated epoxidized soybean oil (AESO) is brittle without flexibility and the incorporation of thermoplastic polyurethane improves its toughness for industrial applications. The hydrophilic functional groups from both oil and polyurethan...

  15. Removal of methyl acrylate by ceramic-packed biotrickling filter and their response to bacterial community.

    PubMed

    Wu, Hao; Yin, Zhenhao; Quan, Yue; Fang, Yingyu; Yin, Chengri

    2016-06-01

    Methyl acrylate is a widely used raw chemical materials and it is toxic in humans. In order to treat the methyl acrylate waste gas, a 3-layer BTF packed with ceramic particles and immobilized with activated sludge was set up. The BTF exhibited excellent removal efficiency that no methyl acrylate could be detected when EBRT was larger than 266s and inlet concentration was lower than 0.19g/m(3). The 1st layer performed the best at fixed inlet concentration of 0.42g/m(3). PCR combined with DGGE was performed to detect the differences in different layers of the BTF. Phylum Proteobacteria (e.g. α-, β-, γ-, δ-) was predominantly represented in the bacterial community, followed by Actinobacteria and Firmicutes. Desulfovibrio gigas, Variovorax paradoxus, Dokdonella koreensis, Pseudoxanthomonas suwonensis, Azorhizobium caulinodans, Hyphomicrobium denitrificans, Hyphomicrobium sp. and Comamonas testosteroni formed the bacteria community to treat methyl acrylate waste gas in the BTF. PMID:26970927

  16. Novel (meth)acrylate monomers for ultrarapid polymerization and enhanced polymer properties

    SciTech Connect

    Beckel, E. R.; Berchtold, K. A.; Nie, J.; Lu, H.; Stansbury, J. W.; Bowman, C. N.

    2002-01-01

    Ultraviolet light is known to be one of the most efficient methods to initiatc polymeric reactions in the presence of a photonitiator. Photopolymerizations are advantageous because the chemistry of the materials can be tailored to design liquid monomers for ultrarapid polymerization into a solid polymer material. One way to achieve rapid photopolymerizations is to utilize multifunctional (meth)acrylate monomers. which form highly crosslinked polymers; however, these monomers typically do not achieve complete functional group conversion. Recently, Decker et al. developed novel monovinyl acrylate monomers that display polyriicrization kinetics that rival those of multifunctional acrylate monomers. These novel acrylate monomers incorporate secondary functionalities and end groups such as carbonates, carbamates, cyclic carbonates and oxazolidone which promote the increased polymerization kinetics of these monomers. In addition to thc polynierization kinetics, these novel monovinyl monomers form crosslinked polymers, which are characterized by having high strength and high flexibility. Unfortunately, the exact mechanism or mechanisms responsible for the polymerization kinetics and crosslinking are not well understood.

  17. Synthesis and self-assembly of poly(3-hexylthiophene)-block-poly(acrylic acid)

    SciTech Connect

    Li, Zicheng; Ono, Robert J.; Wu, Zong-Quan; Bielawski, Christopher W.

    2011-01-01

    A modular and convenient synthesis of ethynyl end functionalized poly(3-hexylthiophene) in high purity is reported; this material facilitated access to poly(3-hexylthiophene)-block-poly(acrylic acid) which self-assembled into hierarchical structures.

  18. Optical properties of UV transmitting acrylics for use in a heavy water Cerenkov detector

    SciTech Connect

    Zwinkels, J.C.; Davidson, W.F.; Dodd, C. )

    1990-08-01

    The absorption, refraction, and scattering properties of several UV transmitting acrylics have been investigated over the wavelength range 300--700 nm using a combination of near-normal incidence regular transmittance and reflectance and diffuse-only reflectance measurements, followed by a Fresnel and a Kubelka-Munk analysis. The samples were evaluated in the as-cast and thermoformed forms, and both before and after an accelerated aging procedure. The results show significant differences in the optical behavior of the various acrylics in the UV region and stress the importance of carefully characterizing acrylic from different sources for each intended use. In our case, acrylic is the proposed material for a heavy water containment vessel for the detection of solar neutrinos. The significance of our findings to the overall performance of this Cerenkov detector, known as the Sudbury neutrino observatory detector, is discussed.

  19. Optical properties of UV transmitting acrylics for use in a heavy water Cerenkov detector.

    PubMed

    Zwinkels, J C; Davidson, W F; Dodd, C X

    1990-08-01

    The absorption, refraction, and scattering properties of several UV transmitting acrylics have been investigated over the wavelength range 300-700 nm using a combination of near-normal incidence regular transmittance and reflectance and diffuse-only reflectance measurements, followed by a Fresnel and a Kubelka-Munk analysis. The samples were evaluated in the as-cast and thermoformed forms, and both before and after an accelerated aging procedure. The results show significant differences in the optical behavior of the various acrylics in the UV region and stress the importance of carefully characterizing acrylic from different sources for each intended use. In our case, acrylic is the proposed material for a heavy water containment vessel for the detection of solar neutrinos. The significance of our findings to the overall performance of this Cerenkov detector, known as the Sudbury neutrino observatory detector, is discussed.

  20. Color stability, water sorption and cytotoxicity of thermoplastic acrylic resin for non metal clasp denture

    PubMed Central

    Jang, Dae-Eun; Lee, Ji-Young; Jang, Hyun-Seon; Lee, Jang-Jae

    2015-01-01

    PURPOSE The aim of this study was to compare the color stability, water sorption and cytotoxicity of thermoplastic acrylic resin for the non-metal clasp dentures to those of thermoplastic polyamide and conventional heat-polymerized denture base resins. MATERIALS AND METHODS Three types of denture base resin, which are conventional heat-polymerized acrylic resin (Paladent 20), thermoplastic polyamide resin (Bio Tone), thermoplastic acrylic resin (Acrytone) were used as materials for this study. One hundred five specimens were fabricated. For the color stability test, specimens were immersed in the coffee and green tee for 1 and 8 weeks. Color change was measured by spectrometer. Water sorption was tested after 1 and 8 weeks immersion in the water. For the test of cytotoxicity, cell viability assay was measured and cell attachment was analyzed by FE-SEM. RESULTS All types of denture base resin showed color changes after 1 and 8 weeks immersion. However, there was no significant difference between denture base resins. All specimens showed significant color changes in the coffee than green tee. In water sorption test, thermoplastic acrylic resin showed lower values than conventional heat-polymerized acrylic resin and thermoplastic polyamide resin. Three types of denture base showed low cytotoxicity in cell viability assay. Thermoplastic acrylic resin showed the similar cell attachment but more stable attachment than conventional heat-polymerized acrylic resin. CONCLUSION Thermoplastic acrylic resin for the non-metal clasp denture showed acceptable color stability, water sorption and cytotoxicity. To verify the long stability in the mouth, additional in vitro studies are needed. PMID:26330974

  1. In vitro cytotoxicity of self-curing acrylic resins of different colors

    PubMed Central

    Retamoso, Luciana Borges; da Cunha, Taís de Morais Alves; Pithon, Matheus Melo; dos Santos, Rogério Lacerda; Martins, Fernanda Otaviano; Romanos, Maria Teresa Villela; Tanaka, Orlando Motohiro

    2014-01-01

    Objective The aim of this study was to assess the in vitro cytotoxicity of acrylic resins of different colors over time. Methods Specimens were divided into 4 groups (n = 6) according to the color of the acrylic resin (Orto Class, Clássico, Campinas, São Paulo, Brazil): Group 1: clear acrylic resin; group 2: pink acrylic resin; group 3: blue acrylic resin and group 4: green acrylic resin. All specimens were fabricated according to the mass manipulation technique and submitted to mechanical polishing protocol. The control was performed with an amalgam specimen (C+), a glass specimen (C-) and cell control (CC). Specimens were immersed in Minimum Eagle's Medium (MEM) and incubated for 24 h at 37ºC. The extracts from the experimental material were filtered and mixed with L929 fibroblast. Cytotoxicity was evaluated at 4 different times, 24, 48, 72 and 168 h. After contact, cells were incubated for 24 h and added to 100 µ of 0.01% neutral red dye. The cells were incubated for 3 h for pigment incorporation and fixed. Cells viability was determined by a spectroscopic (BioTek, Winooski, Vermont, USA) with a 492-nm wavelength λ=492 nm). Results There were no statistical differences between the experimental groups and the CC and C- groups. Conclusion Clear, pink, blue and green self-curing acrylic resins fabricated by means of the mass manipulation technique and mechanically polished are not cytotoxic. Neither the pigment added to the self-curing acrylic resin nor the factor of time influenced the cytotoxicity of the material. PMID:25279523

  2. Testing of gloves for permeability to UV-curable acrylate coatings

    SciTech Connect

    Huggins, R.; Levy, N.; Pruitt, P.M.

    1987-07-01

    The handling of UV-curable acrylate formulations used in the coating of optical fiber requires protective measures to prevent contact dermatitis and/or allergic dermatitis. To characterize the permeability of various glove materials to a UV-curable acrylate coating, a study was undertaken using a modification of a standard ASTM permeability test, which demonstrated that nitrile rubber gloves provided the best protection of those glove materials tested.

  3. Mucoadhesive acrylated block copolymers micelles for the delivery of hydrophobic drugs.

    PubMed

    Eshel-Green, Tal; Bianco-Peled, Havazelet

    2016-03-01

    Blockpolymer micelles having acrylated end groups were fabricated for the development of mucoadhesive drug loaded vehicle. The critical micelle concentration (CMC) of Pluronic(®) F127 modified with acrylate end groups (F127DA) was found to be similar to that of the unmodified Pluronic(®) F127 (F127). Small angle X-ray scattering verified existence of micelles with an inner core of 4.9±0.2 and 5.5±0.3 for F127 and F127DA respectively. Indomethacin, a hydrophobic drug, was incorporated into the micelles using the thin-film hydration method. In vitro drug release assay demonstrated that the micelles sustained the release of the drug in comparison with free drug in solution. Several methods were used for mucoadhesion evaluation. Viscosity profiling was performed by shear rate sweep experiment of hydrated commercial mucin, F127 or F127DA, and combination of both mucin and a copolymer. Elevated viscosity was achieved for acrylated micelles with mucin compared to mixtures of non-acrylated micelles with mucin. The mucoadhesivity of the acrylated micelles was further characterized using nuclear magnetic resonance (NMR); data affirmed the Michael type addition reaction occurred between acrylates on the micelles corona and thiols present in the mucin. SAXS scattering data further showed a modification in the scattering of F127DA micelles with the addition of pig gastric mucin. Cryo-transmission electron microscopy (cryo-TEM) and dynamic light scattering (DLS) data detected increase in the aggregates size while using acrylated micelles enhance mucoadhesion. Thus acrylated F127DA micelles were found to be mucoadhesive, and a suitable and preferred candidate for micellar drug delivery to mucosal surfaces. PMID:26700232

  4. Silver hollow optical fibers with acrylic silicone resin coating as buffer layer for sturdy structure

    NASA Astrophysics Data System (ADS)

    Iwai, Katsumasa; Takaku, Hiroyuki; Miyagi, Mitsunobu; Shi, Yi-Wei; Zhu, Xiao-Song; Matsuura, Yuji

    2016-03-01

    For sturdy silver hollow optical fibers, acrylic silicone resin is newly used as a buffer layer between an inner silver layer and a silica capillary. This acrylic silicone resin film prevents the glass surface from chemical and mechanical micro damages during silver plating process, which deteriorate mechanical strength of the hollow fibers. In addition, it keeps high adhesion of the silver layer with the glass surface. We discuss improvement of mechanical strength of the hollow glass fibers without deterioration of optical properties.

  5. Structure and properties of binary polystyrene-epoxy acrylate oligomer mixtures irradiated by electron beams

    SciTech Connect

    Lomonosova, N.V.

    1995-03-01

    The change in the structure of oriented polymer-oligomer systems based on polystyrene (PS) with M > 10{sup 6} and epoxy acrylate oligomers (aliphatic and aromatic) under irradiation by accelerated electrons was studied using birefringence, isometric heating, IR dichroism, and thermooptical analysis. Mechanical properties of these systems were investigated. It was found that, by adding aliphatic epoxy acrylate to PS and further irradiating this mixture, one can obtain both isotropic and oriented composites with higher strengths, elasticity moduli, and glass transition temperatures.

  6. Structure-activity relationships in the hydrolysis of acrylate and methacrylate esters by carboxylesterase in vitro.

    PubMed

    McCarthy, T J; Witz, G

    1997-01-15

    Acrylate esters are important chemicals in the plastics industry, whose toxicity is theorized to involve alkylation of critical cellular nucleophiles via the Michael addition. Carboxylesterase-mediated hydrolysis of acrylates may be a detoxification mechanism as the unsaturated acid produced is not electrophilic under physiological conditions. Using purified porcine liver carboxylesterase, the enzymatic hydrolysis of several acrylate esters was characterized to determine Km and Vmax values for each ester. The Km (microM) and Vmax (nmol/min) values observed for ethyl acrylate were 134 +/- 16 (S.D.) and 8.9 +/- 2.0, respectively. While the Km for ethyl methacrylate was not significantly different, the Vmax 5.5 +/- 2.5, was significantly lower compared with the corresponding value for ethyl acrylate. The Km and Vmax for butyl acrylate were 33.3 +/- 8.5 microM and 1.49 +/- 0.83 nmol/min, respectively, and the corresponding values for its alpha-methyl analog were not significantly different. The Km and Vmax for tetraethyleneglycol dimethacrylate were 39 +/- 15 microM and 2.9 +/- 1.0 nmol/min, respectively. The Vmax for ethyleneglycol dimethacrylate, 6.9 +/- 2.4 nmol/min, was significantly higher than that of the larger bifunctional ester tetraethyleneglycol dimethacrylate, but the Km was not significantly different. These results indicate that alpha-methyl substitution appears to have a minor effect in the enzymatic hydrolysis of acrylates, and suggest that the relative toxicity of acrylates is not due to differences in carboxylesterase-mediated hydrolysis.

  7. Continuous process of preparation of n-butyl(meth)acrylate by esterification of (meth)acrylic acid by butanol on thermostable sulfo-cation exchanger

    SciTech Connect

    Zheleznaya, L.L.; Karakhanov, R.A.; Lunin, A.F.; Magadov, R.S.; Meshcheryakov, S.V.; Mkrtychan, V.R.; Fomin, V.A.

    1987-11-10

    The authors propose an effective thermostable sulfo-cation exchanger based on polymers with a system of conjugated bonds, sulfopolyphenylene ketone (SPP) differing from the known cation exchangers by the high thermostability (up to 250/sup 0/C), and also having the effect of the stabilization of the double bond in unsaturated monomers. The combination of inhibiting and cation exchange properties makes it also possible to use these sulfo-cation exchangers in the processes of esterification of (meth)acrylic acids by alcohols without addition of special inhibitors. The SPP catalyst was tested in esterification processes of acrylic an methacrylic acid by butanol at a pilot plant.

  8. Starch graft poly(methyl acrylate) loose-fill foam: preparation, properties and degradation.

    PubMed

    Chen, L; Gordon, S H; Imam, S H

    2004-01-01

    Starch graft poly(methyl acrylate) (S-g-PMA) was prepared by ceric ion initiation of methyl acrylate in an aqueous corn starch slurry (prime starch) which maximized the accessibility of the starch for graft polymerization. A new ceric ion reaction sequence was established as starch-initiator-methyl acrylate followed by addition of a small amount of ceric ion solution when the graft polymerization was almost complete to quench the reaction. As a result of this improved procedure, no unreacted methyl acrylate monomer remained, and thus, essentially no ungrafted poly(methyl acrylate) homopolymer was formed in the final grafted product. Quantities of the high purity S-g-PMA so prepared in pilot scale were converted to resin pellets and loose-fill foam by single screw and twin screw extrusion. The use of prime starch significantly improved the physical properties of the final loose-fill foam, in comparison to foam produced from regular dry corn starch. The S-g-PMA loose-fill foam had compressive strength and resiliency comparable to expanded polystyrene but higher bulk density. The S-g-PMA loose-fill foam also had better moisture and water resistance than other competitive starch-based materials. Studies indicated that the starch portion in S-g-PMA loose-fill foam biodegraded rapidly, whereas poly(methyl acrylate) remained relatively stable under natural environmental conditions.

  9. Radiation-induced grafting of acrylic acid onto polypropylene film and its biodegradability

    NASA Astrophysics Data System (ADS)

    Mandal, Dev K.; Bhunia, Haripada; Bajpai, Pramod K.; Chaudhari, C. V.; Dubey, K. A.; Varshney, L.

    2016-06-01

    Polypropylene based commodity polyolefins are widely used in packaging, manufacturing, electrical, pharmaceutical and other applications. The aim of the present work is to study the effect of grafting of acrylic acid on the biodegradability of acrylic acid grafted polypropylene. The effect of different conditions showed that grafting percentage increased with increase in monomer concentration, radiation dose and inhibitor concentration but decreased with increase in radiation dose rate. The maximum grafting of 159.4% could be achieved at optimum conditions. The structure of grafted polypropylene films at different degree of grafting was characterized by EDS, FTIR, TGA, DSC, SEM and XRD. EDS studies showed that the increase in acrylic acid grafting percentage increased the hydrophilicity of the grafted films. FTIR studies indicated the presence of acrylic acid on the surface of polypropylene film. TGA studies revealed that thermal stability decreased with increase in grafting percentage. DSC studies showed that melting temperature and crystallinity of the grafted polypropylene films lower than polypropylene film. SEM studies indicated that increase in acrylic acid grafting percentage increased the wrinkles in the grafted films. The maximum biodegradability could be achieved to 6.85% for 90.5% grafting. This suggested that microorganisms present in the compost could biodegrade acrylic acid grafted polypropylene.

  10. MM and QM: Conformational and vibrational spectra analysis of 2-hydroxyethyl acrylate

    NASA Astrophysics Data System (ADS)

    Belaidi, O.; Adjim, M.; Bouchaour, T.; Maschke, U.

    2015-02-01

    2-Hydroxyethyl acrylate is generally used with other acrylic and methacrylic products in order to get the desired characteristics of the final product. In this work we are about to make an assignment of experimental infrared bands with the help of a theoretical quantum chemistry calculations. The exact knowledge of some bands which are not characteristics of acrylic materials will enable us to make a quick analysis with available techniques of low costs for mixtures of polymers based on acrylate and methacrylate molecules. In the experimental part, the infrared spectrum of 2-hydroxyethyl acrylate is obtained by using a FTIR Perkin Elmer model 2000. In the computational part and as first step, the theoretical calculations are performed by the semi-empirical AM1 method for excluding similar structures of 2-hydroxyethyl acrylate molecule by a meticulous conformational analysis. As a second step the obtained structures are optimized using DFT. The simulated frequencies are then scaled and a tentative assignment is made based on band intensities and PED percentages. The theoretical calculations predict the existence of thirteen conformations two of them represent the majority of experimental bands in the infrared spectrum. Two neighbor experimental bands located at 1301 and 1207 cm-1 maybe used as characteristic bands to locate and distinguish the existence of one or both conformations.

  11. Hybrid resist systems based on α-substituted acrylate copolymers

    NASA Astrophysics Data System (ADS)

    Ito, Hiroshi; Sundberg, Linda K.; Bozano, Luisa; Lofano, Elizabeth M.; Yamanaka, Kazuhiro; Terui, Yoshiharu; Fujiwara, Masaki

    2009-03-01

    Classical electron-beam resists such as poly(methyl methacrylate) (PMMA) and Nippon Zeon's ZEP function as high resolution and low roughness positive resists on the basis of radiation induced main chain scission to reduce the molecular weight while chemical amplification resists utilized in device manufacturing function on the basis of acidcatalyzed deprotection to change the polarity. In an attempt to increase the resolution and reduce the line roughness of chemical amplification resists, we prepared copolymers that undergo radiation induced main chain scission and acidcatalyzed deprotection. In another word, we wanted to increase the sensitivity of the PMMA resist by incorporating the acid-catalyzed deprotection mechanism in polymers that undergo main chain scission, maintaining the high resolution and low roughness of PMMA. To synthesize such hybrid resist polymers, we selected α-substituted acrylates and α- substituted styrenes. The former included methyl methacrylate (MMA), t-butyl methacrylate (TBMA), methyl α- fluoroacrylate (MFA), t-butyl α-fluoroacrylate (TBFA), and t-butyl α-trifluoromethylacrylate (TBTFMA) and the latter α-methylstyrene (αMEST), α-methyleneindane (αMEIN), and α-methylenetetralin (αMETL). The α-substituted tbutyl acrylic esters were copolymerized with the methyl esters and also with α-substituted styrenic monomers using 2, 2'-azobis(isobutyronitrile) (AIBN). Hybrid resists were formulated by adding a photochemical acid generator and a base quencher to the copolymers and developers were selected by studying the dissolution behavior of unexposed and 254 nm exposed resist films using a quartz crystal microbalance (QCM). In addition to the difference in the imaging mechanism, PMMA and ZEP differ from the chemical amplification resists in developers; organic solvent vs. aqueous base. We were interested in looking also into the influence of the developer on the lithographic performance. Contrast curves were generated by exposing

  12. Probing the Aggregation Behavior of Neat Imidazolium-Based Alkyl Sulfate (Alkyl = Ethyl, Butyl, Hexyl, and Octyl) Ionic Liquids through Time Resolved Florescence Anisotropy and NMR and Fluorescence Correlation Spectroscopy Study.

    PubMed

    Majhi, Debashis; Pabbathi, Ashok; Sarkar, Moloy

    2016-01-14

    Aggregation behavior of a series of neat 1-ethyl 3-methylimidazolium alkyl sulfate (alkyl = ethyl, butyl, hexyl, and octyl) ionic liquids has been investigated through combined time-resolved fluorescence spectroscopy, 1-D and 2-D NMR spectroscopy, and fluorescence correlation spectroscopy (FCS). Interestingly, experimentally measured rotational relaxation times (τr) for ethyl, butyl, hexyl and octyl systems are measured to be 2.25, 1.64, 1.36, and 1.32 times higher than the estimated (from Stokes-Einstein-Debye theory) values for the same respective systems. This indicates that the emitting species is not the monomeric imidazolium moiety rather an associated species, and volume of the rotating fluorescing species decreases even though the length of the alkyl moiety on the anions is increased. The shift in the (1)H proton signal as well as a change in the width of the same signal upon dilution of the neat ionic liquids indicates that ionic liquids exist in the aggregated form. Further investigation through the 2D-ROESY experiment shows that interaction between imidazolium and sulfate is relatively stronger in the ethyl system than that of the longer octyl system. FCS measurements independently show that the hydrodynamic volume decreases with an increase in the anion chain length. The NMR and FCS results are consistent with the findings of the fluorescence anisotropy study. PMID:26654730

  13. Bone Marrow Nails Created by Percutaneous Osteoplasty for Long Bone Fracture: Comparisons Among Acrylic Cement Alone, Acrylic-Cement-Filled Bare Metallic Stent, and Acrylic-Cement-Filled Covered Metallic Stent

    SciTech Connect

    Nakata, Kouhei; Kawai, Nobuyuki; Sato, Morio Cao, Guang; Sahara, Shinya; Sonomura, Tetsuo; Takasaka, Isao; Minamiguchi, Hiroki; Nakai, Motoki

    2011-06-15

    Purpose: This study was designed to compare the strength among bone marrow nails created to treat long bone fractures using interventional procedures. Methods: Twelve resected intact tibiae of healthy swine were used. A circumferential bone fracture was made in nine tibiae and restored with the following created bone marrow nails: acrylic cement alone (ACA) (n = 3), acrylic-cement-filled bare metallic stent (AC-FBMS) (n = 3), and acrylic-cement-filled covered metallic (AC-FCMS) stent (n = 3). The remaining intact tibiae (n = 3) were used as controls. Results: A bone marrow nail was successfully achieved within 30 min in all swine. The maximum injection volume of acrylic cement for creating ACA, AC-FBMS, and AC-FCMS was 1.7 {+-} 0.3, 3.2 {+-} 0.4, and 2.9 {+-} 0.4 mL, respectively. The thickness of bone marrow nail created in the ACA, AC-FBMS, and AC-FCMS groups was 3.6 {+-} 1.0, 10.3 {+-} 0.26, and 9.6 {+-} 0.32 mm, respectively (AC-FBMS group versus AC-FCMS group, p = 0.038), probably because of leakage of acrylic cement surrounding the interstices. The maximum bending power (kilonewton) and bending strength (newton/mm{sup 2}) in the normal long bone, ACA, AC-FBMS, and AC-FCMS groups were: 1.70 {+-} 0.25 and 79.2 {+-} 16.1; 0.21 {+-} 0.11 and 8.8 {+-} 2.8; 0.46 {+-} 0.06 and 18.2 {+-} 1.6; and 0.18 {+-} 0.04 and 7.8 {+-} 2.7, respectively. Conclusions: Although the maximum bending power and bending strength of AC-FBMS were not satisfactory, it was the most robust of the three marrow nails for restoring fractured long bone.

  14. [Adaptation of acrylic resin dentures polymerized using various activation modes].

    PubMed

    Takamata, T; Inoue, Y; Hashimoto, K; Sugitou, S; Arakawa, H; Kurasawa, I

    1989-12-01

    The purpose of this in vitro study was to compare the dimensional accuracy of maxillary dentures made using a conventional heat-activated PMMA resin, a pour resin, a visible light-activated resin, and a microwave-activated acrylic resin. Two simple methods for measuring dimensional accuracy were used: (1) weight of impression material entrapped between the base and master die and (2) measurement of the posterior border gap at five locations. The volume of space between the denture base and the master die was determined by (1) computation and (2) estimation. Statistical analysis (Bartlett, ANOVA and Tukey's Tests) supported the following conclusions: (1) all groups showed a processing contraction, most apparent from buccal flange to buccal flange, (2) the poorest fitting group was processed in a brass flask and a water bath at a temperature which rose from 70 to 100 degrees C, using a heat activated resin (Acron), (3) the visible light activated resin (Triad) produced dentures of intermediate accuracy, as did Acupac 20 when either heat or microwave activated, (4) the two best fitting groups were prepared from a chemically activated resin system using pressure at low heat (PER form), and the resin developed for microwave activation (Acron MC).

  15. Radiation grafting of acrylic acid onto polypropylene films

    NASA Astrophysics Data System (ADS)

    Taher, N. H.; Dessouki, A. M.; Khalil, F. H.

    A study has been made for the preparation of membranes by the direct radiation grafting of acrylic acid (AAc) onto polypropylene (PP) films. The appropriate reaction conditions were selected under which the graft polymerization was carried out successfully. The effect of different solvents such as benzene, methanol/water mixture, isopropanol/water mixture, dimethyl formalide and distilled water on the swelling and grafting process of AAc onto PP films was investigated. In this grafting system ammonium ferrous sulphate (Mohr's salt) and ferric chloride were used as inhibitors to minimize the homopolymerization of AAc and the suitable concentration of the inhibitor was found to be 1.0 and 1.5 wt% for Mohr's salt and ferric chloride, respectively. Also, the effect of monomer concentration on the rate of grafting was investigated. The dependence of the grafting rate on monomer concentration was found to be 1.1 order. This grafting system proceeded by diffusion controlled process. Some selected properties of the grafted films such as swelling behavior, gel determination, mechanical and electrical properties were also investigated. It was found that the grafted membranes possess good hydrophilic properties which may make them promising in some practical applications.

  16. Prosthetic rehabilitation of the gagging patient using acrylic training plates.

    PubMed

    Ali, Rahat; Altaie, Asmaa; Morrow, Leean

    2015-01-01

    Patients with a hyper-responsive gag reflex pose dentists with a challenging problem. The gag reflex of some patients may be so severe that patients (and operating clinician) may favour extraction of any painful, infected teeth as opposed to more lengthy and complicated procedures such as root canal therapy. However, consistently adopting this approach may render the gagging patient completely edentulous. Such patients may then present to the dental surgeon requesting tooth replacement with some form of denture. This in itself can be a challenging task given the difficulties one may experience whilst taking impressions in this cohort of patients. This article will discuss the prosthetic management of the maxillary arch in edentulous patients with a severe gag reflex. There will be particular emphasis on the aetiology and physiology of the gag reflex, impression-taking techniques to allow the construction of an acrylic training plate (as an interim measure), principles of training plate design and construction of the definitive removable denture. Clinical Relevance: Removable training plates can be used as an interim measure to desensitize edentulous gagging patients before providing them with a definitive removable denture.

  17. Interaction of photosensitive surfactant with DNA and poly acrylic acid

    SciTech Connect

    Zakrevskyy, Yuriy Paasche, Jens; Lomadze, Nino; Santer, Svetlana; Cywinski, Piotr; Cywinska, Magdalena; Reich, Oliver; Löhmannsröben, Hans-Gerd

    2014-01-28

    In this paper, we investigate interactions and phase transitions in polyelectrolyte-surfactant complexes formed between a cationic azobenzene-containing surfactant and two types of polyelectrolytes: natural (DNA) or synthetic (PAA: poly acrylic acid). The construction of a phase diagram allowed distancing between four major phases: extended coil conformation, colloidally stable compacted globules, colloidal instability range, and surfactant-stabilized compact state. Investigation on the complexes’ properties in different phases and under irradiation with UV light provides information about the role of the surfactant's hydrophobic trans isomers both in the formation and destruction of DNA and PAA globules as well as in their colloidal stabilization. The trans isomer shows much stronger affinity to the polyelectrolytes than the hydrophilic cis counterpart. There is no need for complete compensation of the polyelectrolyte charges to reach the complete compaction. On contrary to the findings previously reported in the literature, we demonstrate – for the first time – complete polyelectrolyte compaction which occurs already at 20% of DNA (and at 50% of PAA) charge compensation. The trans isomer plays the main role in the compaction. The aggregation between azobenzene units in the photosensitive surfactant is a driving force of this process. The decompaction can be realized during UV light irradiation and is strongly influenced by the interplay between surfactant-surfactant and surfactant-DNA interactions in the compacted globules.

  18. Synthesis of acrylates and methacrylates from coal-derived syngas

    SciTech Connect

    Spivey, J.J.; Gogate, M.R.; Jang, B.W.L.

    1995-12-31

    Acrylates and methacrylates are among the most widely used chemical intermediates in the world. One of the key chemicals of this type is methyl methacrylate. Of the 4 billion pounds produced each year, roughly 85% is made using the acetone-cyanohydrin process, which requires handling of large quantities of hydrogen cyanide and produces ammonium sulfate wastes that pose an environmental disposal challenge. The U.S. Department of Energy and Eastman Chemical Company are sharing the cost of research to develop an alternative process for the synthesis of methyl methacrylate from syngas. Research Triangle Institute is focusing on the synthesis and testing of active catalysts for the condensation reactions, and Bechtel is analyzing the costs to determine the competitiveness of several process alternatives. Results thus far show that the catalysts for the condensation of formaldehyde and the propionate are key to selectively producing the desired product, methacrylic acid, with a high yield. These condensation catalysts have both acid and base functions and the strength and distribution of these acid-base sites controls the product selectivity and yield.

  19. Color stability of acrylic resin adhesives with different initiation modes.

    PubMed

    Tanoue, Naomi; Koishi, Yoshikazu; Yanagida, Hiroaki; Atsuta, Mitsuru; Shimada, Kazuki; Matsumura, Hideo

    2004-09-01

    The purpose of this study was to evaluate the color stability of two acrylic resin adhesives with different activation systems: a benzoyl peroxide (BPO)-amine redox system and a tri-n-butylborane (TBB) derivative system. The colorimetric values of the two resins in different shades (Clear and Ivory) were determined (n=5) 24 hours after polymerization as a baseline using the L*a*b* system of the Commission Internationale de l'Eclairage (CIE). The specimens were thereafter immersed in distilled water, and the color difference (deltaE*) values were calculated. After 24 weeks, the TBB-initiated material showed a significantly (p<0.05) lower color change than the BPO-amine-initiated material. The deltaE* values for the BPO-amine-initiated materials were 6.9 for Clear and 15.8 for Ivory, whereas those for the TBB-initiated materials were 1.3 and 1.8 respectively. Thus, it was concluded that the TBB-initiated material had superior color stability to that of the BPO-amine-initiated material.

  20. Cytocompatible antifungal acrylic resin containing silver nanoparticles for dentures

    PubMed Central

    Acosta-Torres, Laura Susana; Mendieta, Irasema; Nuñez-Anita, Rosa Elvira; Cajero-Juárez, Marcos; Castaño, Víctor M

    2012-01-01

    Background Inhibition of Candida albicans on denture resins could play a significant role in preventing the development of denture stomatitis. The safety of a new dental material with antifungal properties was analyzed in this work. Methods Poly(methyl methacrylate) [PMMA] discs and PMMA-silver nanoparticle discs were formulated, with the commercial acrylic resin, Nature-CrylTM, used as a control. Silver nanoparticles were synthesized and characterized by ultraviolet-visible spectroscopy, dispersive Raman spectroscopy, and transmission electron microscopy. The antifungal effect was assessed using a luminescent microbial cell viability assay. Biocompatibility tests were carried out using NIH-3T3 mouse embryonic fibroblasts and a Jurkat human lymphocyte cell line. Cells were cultured for 24 or 72 hours in the presence or absence of the polymer formulations and analyzed using three different tests, ie, cellular viability by 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay, and cell proliferation by enzyme-linked immunosorbent assay BrdU, and genomic DNA damage (Comet assay). Finally, the samples were evaluated mechanically, and the polymer-bearing silver nanoparticles were analyzed microscopically to evaluate dispersion of the nanoparticles. Results The results show that PMMA-silver nanoparticle discs significantly reduce adherence of C. albicans and do not affect metabolism or proliferation. They also appear not to cause genotoxic damage to cells. Conclusion The present work has developed a new biocompatible antifungal PMMA denture base material. PMID:22969297

  1. Spallation Characteristics of Poly-Methyl Meth-Acrylic (PMMA)

    NASA Astrophysics Data System (ADS)

    Bartkowski, Peter; Dandekar, D. P.

    1999-06-01

    This work describes the results derived from plane shock wave spallation experiments performed on Poly-Methyl Meth-Acrylic (PMMA) Polymer. These experiments were conducted using the Army Research Laboratories 102 mm Bore, 8 m long Light Gas Gun located at Aberdeen Proving Ground, MD. The PMMA used in this work was manufactured by Rohm & Haas as their Ultra-Violet Absorbing (UVA), Type II Plexiglass. Its density is 1.188 Mg/m3 and longitudinal shock velocity is 2.72 mm/μ s. Spallation experiments were conducted at impact stresses between 0.2 and 2.0 GPa. The PMMA appears to exhibit a constant tensile strength of 0.15 GPa up to an impact stress of 0.75 GPa. Unlike metal and ceramic materials, the PMMA exhibits a dwell time in the spallation inversly proportional to the impact stress. At a low impact stress of 0.40 GPa, spallation of the PMMA occurs over a time period of 0.80 micro-seconds. At an impact stress of 0.75 GPa, the spallation occurs over 0.40 micro-seconds. This variation in time required to spall the PMMA will be analyzed and theories discussed.

  2. Thiol-ene/acrylate substrates for softening intracortical electrodes.

    PubMed

    Ware, Taylor; Simon, Dustin; Liu, Clive; Musa, Tabassum; Vasudevan, Srikanth; Sloan, Andrew; Keefer, Edward W; Rennaker, Robert L; Voit, Walter

    2014-01-01

    Neural interfaces have traditionally been fabricated on rigid and planar substrates, including silicon and engineering thermoplastics. However, the neural tissue with which these devices interact is both 3D and highly compliant. The mechanical mismatch at the biotic-abiotic interface is expected to contribute to the tissue response that limits chronic signal recording and stimulation. In this work, novel ternary thiol-ene/acrylate polymer networks are used to create softening substrates for neural recording electrodes. Thermomechanical properties of the substrates are studied through differential scanning calorimetry and dynamic mechanical analysis both before and after exposure physiological conditions. This substrate system softens from more than 1 GPa to 18 MPa on exposure to physiological conditions: reaching body temperature and taking up less than 3% fluid. The impedance of 177 µm(2) gold electrodes electroplated with platinum black fabricated on these substrates is measured to be 206 kΩ at 1 kHz. Specifically, intracortical electrodes are fabricated, implanted, and used to record driven neural activity. This work describes the first substrate system that can use the full capabilities of photolithography, respond to physiological conditions by softening markedly after insertion, and record driven neural activity for 4 weeks.

  3. Acrylic bone cement in total joint arthroplasty: A review.

    PubMed

    Saleh, Khaled J; El Othmani, Mouhanad M; Tzeng, Tony H; Mihalko, William M; Chambers, Monique C; Grupp, Thomas M

    2016-05-01

    Acrylic bone cement has a variety of applications in orthopedic surgery. Primary uses in total arthroplasties are limited to prostheses fixation and antibiotic delivery. With the large number of total joint arthroplasties expected to continue to rise, understanding the role bone cement plays in the success of total joint arthroplasty can have a significant impact on daily practice. The literature is inconclusive on whether cemented or cementless fixation technique is superior, and choice of fixation type is mainly determined by surgeon preference and experience. Surgeons should understand that if poor techniques exist, short-term outcomes of the replaced joint may be at risk. Statement of clinical significance: This article attempts to clarify some points of bone cement use through a review of the mechanical properties related to bone cement, a comparison to alternative materials, influence of additives, and the effects on surgical outcomes. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 34:737-744, 2016. PMID:26852143

  4. Interaction of photosensitive surfactant with DNA and poly acrylic acid.

    PubMed

    Zakrevskyy, Yuriy; Cywinski, Piotr; Cywinska, Magdalena; Paasche, Jens; Lomadze, Nino; Reich, Oliver; Löhmannsröben, Hans-Gerd; Santer, Svetlana

    2014-01-28

    In this paper, we investigate interactions and phase transitions in polyelectrolyte-surfactant complexes formed between a cationic azobenzene-containing surfactant and two types of polyelectrolytes: natural (DNA) or synthetic (PAA: poly acrylic acid). The construction of a phase diagram allowed distancing between four major phases: extended coil conformation, colloidally stable compacted globules, colloidal instability range, and surfactant-stabilized compact state. Investigation on the complexes' properties in different phases and under irradiation with UV light provides information about the role of the surfactant's hydrophobic trans isomers both in the formation and destruction of DNA and PAA globules as well as in their colloidal stabilization. The trans isomer shows much stronger affinity to the polyelectrolytes than the hydrophilic cis counterpart. There is no need for complete compensation of the polyelectrolyte charges to reach the complete compaction. On contrary to the findings previously reported in the literature, we demonstrate - for the first time - complete polyelectrolyte compaction which occurs already at 20% of DNA (and at 50% of PAA) charge compensation. The trans isomer plays the main role in the compaction. The aggregation between azobenzene units in the photosensitive surfactant is a driving force of this process. The decompaction can be realized during UV light irradiation and is strongly influenced by the interplay between surfactant-surfactant and surfactant-DNA interactions in the compacted globules. PMID:25669583

  5. Controlled Transdermal Iontophoresis by Polypyrrole/Poly(Acrylic Acid) Hydrogel

    NASA Astrophysics Data System (ADS)

    Chansai, Phithupha; Sirivat, Anuvat

    2008-03-01

    Transdermal drug delivery system delivers a drug into a body at desired site and rate. The conductive polymer-hydrogel blend between polypyrrole (PPy) doped with anionic drug and poly(acrylic acid) (PAA) were developed as a matrix/carrier of drug for the transdermal drug delivery in which the characteristic releases depend on the electrical field applied. The PAA films and their blend films were prepared by solution casting using ethylene glycol dimethacrylate (EGDMA) as a crosslinking agent. A mechanical blending of PPy particles and PAA matrix was then carried out. Drug diffusions in the blended PPy/PAA hydrogel and the non-blended one were investigated and determined by using a modified Franz-diffusion cell with an acetate buffer, pH 5.5, at 37 0C, for a period of 48 hours to determine the effects of crosslinking ratio and electric field strength. Amounts of the released drug were measured by UV-Visible spectrophotometry. The diffusion coefficient of drug was determined through the Higuchi equation via different conditions, with and without an electric field. Moreover, thermal properties and electrical conductivity of the polypyrrole and drug-loaded polypyrrole were investigated by means of the thermogravimetric analysis and by using a two-point probe meter, respectively.

  6. [Comparative analysis of tissue reaction to acrylic resin materials in studies on Wistar strain rats].

    PubMed

    Sobolewska, E

    1999-01-01

    The study takes up the issue of assessing rat tissue reaction to operatively inserted implants of different acrylic resin materials used in prosthetic dentistry. The materials subjected to analysis were polyacrylics: Vertex Soft, Vertex R.S., Vertex S.C., Superacryl and silicone material Molloplast B. The prolongation of life and the dynamic development of prosthetic treatment have caused removable dentures to be used longer and among more people. Polymerised acrylic resin material of these dentures is a potential pathogenic factor to the oral cavity mucosa which is in contact with it. As many as 20 to 70% of patients using removable acrylic dentures suffer from prosthetic stomatopathy. It is considered that the mucosa irritation may be caused by denture trauma, a mycotic infection or toxic action of some components of acrylic materials. Therefore the use of new generation acrylic materials in producing prosthetic dentures needs a precise assessment of undesirable local and systemic effects. A comparative analysis of the effect of correctly polymerised acrylic material on rat mucosa, parotid glands and lymphatic nodes was carried out. Systemic toxicity of these materials was assessed. Acrylic plates were prepared from the most often used acrylic resin materials in the Department of Prosthetic Dentistry PAM and a silicone material (these materials were polymerised precisely according to the producers instruction). Before implantation the plates underwent a thermodynamic analysis in order to ensure that the polymerisation process was carried out correctly and to determine thermal resistance of particular materials. Next sterile acrylic plates were implanted in rats under general anaesthesia. The animals were divided into 6 groups, 10 rats each. In four groups acrylic plates were implanted, in one group silicone material plates were implanted and it represented the comparative group, in one control group an incision of the buccal mucosa was made. The rats were

  7. [Comparative analysis of tissue reaction to acrylic resin materials in studies on Wistar strain rats].

    PubMed

    Sobolewska, E

    1999-01-01

    The study takes up the issue of assessing rat tissue reaction to operatively inserted implants of different acrylic resin materials used in prosthetic dentistry. The materials subjected to analysis were polyacrylics: Vertex Soft, Vertex R.S., Vertex S.C., Superacryl and silicone material Molloplast B. The prolongation of life and the dynamic development of prosthetic treatment have caused removable dentures to be used longer and among more people. Polymerised acrylic resin material of these dentures is a potential pathogenic factor to the oral cavity mucosa which is in contact with it. As many as 20 to 70% of patients using removable acrylic dentures suffer from prosthetic stomatopathy. It is considered that the mucosa irritation may be caused by denture trauma, a mycotic infection or toxic action of some components of acrylic materials. Therefore the use of new generation acrylic materials in producing prosthetic dentures needs a precise assessment of undesirable local and systemic effects. A comparative analysis of the effect of correctly polymerised acrylic material on rat mucosa, parotid glands and lymphatic nodes was carried out. Systemic toxicity of these materials was assessed. Acrylic plates were prepared from the most often used acrylic resin materials in the Department of Prosthetic Dentistry PAM and a silicone material (these materials were polymerised precisely according to the producers instruction). Before implantation the plates underwent a thermodynamic analysis in order to ensure that the polymerisation process was carried out correctly and to determine thermal resistance of particular materials. Next sterile acrylic plates were implanted in rats under general anaesthesia. The animals were divided into 6 groups, 10 rats each. In four groups acrylic plates were implanted, in one group silicone material plates were implanted and it represented the comparative group, in one control group an incision of the buccal mucosa was made. The rats were

  8. NTP-CERHR Monograph on the Potential Human Reproductive and Developmental Effects of Di-n-Hexyl Phthalate (DnHP).

    PubMed

    2003-05-01

    The National Toxicology Program (NTP) Center for the Evaluation of Risks to Human Reproduction (CERHR) conducted an evaluation of the potential for di-n-hexyl phthalate (DnHP) to cause adverse effects on reproduction and development in humans. DnHP is one of 7 phthalate chemicals evaluated by the NTP CERHR Phthalates Expert Panel. These phthalates were selected for evaluation because of high production volume, extent of human exposures, use in children's products, and/or published evidence of reproductive or developmental toxicity. Available information indicates that DnHP is manufactured in relatively small amounts but occurs in a variety of commercial products including dip-molded products such as tool handles or dishwasher baskets, flooring, vinyl gloves, flea collars, and conveyer belts used in food processing. The results of this evaluation on DnHP are published in an NTP-CERHR monograph which includes: 1) the NTP Brief, 2) the Expert Panel Report on the Reproductive and Developmental Toxicity of DnHP, and 3) public comments received on the Expert Panel Report. As stated in the NTP Brief, the NTP reached the following conclusions regarding the possible effects of exposure to DnHP on human development and reproduction. The scientific evidence was insufficient to reach a conclusion regarding the potential for DnHP to adversely affect human development or reproduction. There was very limited information on developmental and reproductive toxicity available to the panel. The panel evaluated only a single developmental toxicity study using a high dose (9,900 mg/kg body weight/day on gestational days 6-13) of DnHP. No live pups were delivered. In a reproductive study, effects on fertility were noted in all treatment groups (380-1,670 mg/ kg body weight/day). These studies provided sufficient information in experimental animals to conclude that DnHP is a reproductive and developmental toxicant at the doses tested. However, the treatment doses were high and these

  9. Thermo-Optic Coefficient of Different Photosensitive Acrylate Polymers for Optical Application

    NASA Astrophysics Data System (ADS)

    Razali, N.; Mohamed, R.; Ehsan, A. A.; Kuang, C. S.; Shaari, S.

    Thermo-optic (TO) effect in materials can be exploited in the fabrication of optical devices such as optical switches and couplers. These optical devices play a key function in communication networks because by changing the temperature they have control over the optical path. Recently, polymer materials have begun to receive attention for the application of the TO switch in integrated optics. The polymers exploited for the variation of refractive index with temperature in our work involve the use of cyclomer acrylate, which is compared to the fluorinated acrylate available in the market. We focus the on cyclomer acrylate resin potential to be employed in fabricating optical devices especially the optical waveguide and optical switch. Formerly, this polymer is used as an adhesive and coating only. Different acrylate formulations from cyclomer acrylates have been exploited. Both acrylates show negative TO effects with temperature i.e. decrease of refractive index result in the increase in temperature. This is expected as the refractive index of the polymers are reduced, as density typically decreases with increasing temperature. This is in accordance to the dependence of polarizability and density of a particular material, to its refractive index. For both types of polymers, the change of the refractive index as a function of temperature is linear. The slope can give the dn/dT of the film. The dn/dT of polymers are as high as the order of 10-4, which is comparable to those of optical polymers. Higher values are shown by the cyclomer acrylate compared to the fluorinated type.

  10. Structural degradation of acrylic bone cements due to in vivo and simulated aging.

    PubMed

    Hughes, Kerry F; Ries, Michael D; Pruitt, Lisa A

    2003-05-01

    Acrylic bone cement is the primary load-bearing material used for the attachment of orthopedic devices to adjoining bone. Degradation of acrylic-based cements in vivo results in a loss of structural integrity of the bone-cement-prosthesis interface and limits the longevity of cemented orthopedic implants. The purpose of this study is to investigate the effect of in vivo aging on the structure of the acrylic bone cement and to develop an in vitro artificial aging protocol that mimics the observed degradation. Three sets of retrievals are examined in this study: Palacos brand cement retrieved from hip replacements, and Simplex brand cement retrieved from both hip and knee replacement surgeries. In vitro aging is performed using oxidative and acidic environments on three acrylic-based cements: Palacos, Simplex, and CORE. Gel permeation chromatography (GPC) and Fourier transform infrared spectroscopy (FTIR) are used to examine the evolution of molecular weight and chemical species within the acrylic cements due to both in vivo and simulated aging. GPC analysis indicates that molecular weight is degraded in the hip retrievals but not in the knee retrievals. Artificial aging in an oxidative environment best reproduces this degradation mechanism. FTIR analysis indicates that there exists a chemical evolution within the cement due to in vivo and in vitro aging. These findings are consistent with scission-based degradation schemes in the cement. Based on the results of this study, a pathway for structural degradation of acrylic bone cement is proposed. The findings from this investigation have broad applicability to acrylic-based cements and may provide guidance for the development of new bone cements that resist degradation in the body.

  11. Effect of light-curing, pressure, oxygen inhibition, and heat on shear bond strength between bis-acryl provisional restoration and bis-acryl repair materials

    PubMed Central

    Shim, Ji-Suk; Lee, Jeong-Yol; Choi, Yeon-Jo; Shin, Sang-Wan

    2015-01-01

    PURPOSE This study aimed to discover a way to increase the bond strength between bis-acryl resins, using a comparison of the shear bond strengths attained from bis-acryl resins treated with light curing, pressure, oxygen inhibition, and heat. MATERIALS AND METHODS Self-cured bis-acryl resin was used as both a base material and as a repair material. Seventy specimens were distributed into seven groups according to treatment methods: pressure - stored in a pressure cooker at 0.2 Mpa; oxygen inhibition- applied an oxygen inhibitor around the repaired material,; heat treatment - performed heat treatment in a dry oven at 60℃, 100℃, or 140℃. The shear bond strength was measured with a universal testing machine, and the shear bond strength (MPa) was calculated from the peak load of failure. A comparison of the bond strength between the repaired specimens was conducted using one-way ANOVA and Tukey multiple comparison tests (α=.05). RESULTS There were no statistically significant differences in the shear bond strength between the control group and the light curing, pressure, and oxygen inhibition groups. However, the heat treatment groups showed statistically higher bond strengths than the groups treated without heat, and the groups treated at a higher temperature resulted in higher bond strengths. Statistically significant differences were seen between groups after different degrees of heat treatment, except in groups heated at 100℃ and 140℃. CONCLUSION Strong bonding can be achieved between a bis-acryl base and bis-acryl repair material after heat treatment. PMID:25722837

  12. The effect of various frequencies of ultrasonic cleaner in reducing residual monomer in acrylic resin.

    PubMed

    Charasseangpaisarn, Taksid; Wiwatwarrapan, Chairat

    2015-12-01

    Monomer remaining in denture base acrylic can be a major problem because it may cause adverse effects on oral tissue and on the properties of the material. The purpose of this study was to compare the effect of various ultrasonic cleaner frequencies on the amount of residual monomer in acrylic resin after curing. Forty-two specimens each of Meliodent heat-polymerized acrylic resin (M) and Unifast Trad Ivory auto-polymerized acrylic resin (U) were prepared according to their manufacturer's instructions and randomly divided into seven groups: Negative control (NC); Positive control (PC); and five ultrasonic treatment groups: 28 kHz (F1), 40 kHz (F2), 60 kHz (F3) (M=10 min, U=5 min), and 28 kHz followed by 60 kHz (F4: M=5 min per frequency, U=2.5 min per frequency, and F5: M=10 min followed by 5 min per frequency, U=5 min followed by 2.5 min per frequency). Residual monomer was determined by HPLC following ISO 20795-1. The data were analyzed by One-way ANOVA and Tukey HSD. There was significantly less residual monomer in the auto-polymerized acrylic resin in all ultrasonic treatment groups and the PC group than that of the NC group (p<0.05). However, the amount of residual monomer in group F3 was significantly higher than that of the F1, F4, and PC groups (p<0.05). In contrast, ultrasonic treatment did not reduce the amount of residual monomer in heat-polymerized acrylic resin (p>0.05). The amount of residual monomer in heat-polymerized acrylic resin was significantly lower than that of auto-polymerized acrylic resin. In conclusion, ultrasonic treatment at low frequencies is recommended to reduce the residual monomer in auto-polymerized acrylic resin and this method is more practical in a clinical situation than previously recommended methods because of reduced chairside time.

  13. Glubran 2: A New Acrylic Glue for Neuroradiological Endovascular Use

    PubMed Central

    Leonardi, M.; Barbara, C.; Simonetti, L.; Giardino, R.; Nicoli Aldini, N.; Fini, M.; Martini, L.; Masetti, L.; Joechler, M.; Roncaroli, F.

    2002-01-01

    Summary A new acrylic glue, Glubran 2, is now available on the European market. It bears the CE mark with several surgical indications and the specific indication for neuroradiological endovascular use. Despite this approval, to our knowledge its use is still limited to surgery and no injections have been made in human patients. This study was designed to evaluate the behavior of Glubran 2 in endovascular injection in a simulation of brain AVM. Six sheep were operated on opening a fistula between the right common carotid artery and the jugular vein. This fistula modifies blood flow in the skull base rete mirabilis, which then functions as an AVM. In two sheep, the rete mirabilis was occluded by injection of 1.5 ml of Histoacryl diluted 1:1 and 1:3 with Lipiodol. In two sheep, the rete was embolized by injection of 1.5 ml of Glubran 2 diluted 1:1 with Lipiodol. The last two sheep were embolized by injection of Glubran 2 diluted 1:3 with Lipiodol. The procedures were documented by DSA angiographic acquisitions and by fluoroscopic VHS. The sheep were killed immediately after the procedures and the rete mirabilis isolated for histologic examination. Embolization was obtained with both kinds of glue. Glubran 2 diffuses in a very similar way to Histoacryl with an apparently more complete diffusion. Reflux in the ascending pharyngeal artery showed that Glubran 2 tended not to produce bubbles but diffused more homogeneously. The subjective conclusion of this work is that Glubran 2 can be used in endovascular embolizations. Before approaching brain AVMs, a further study will investigate embolization of the external carotid territory. PMID:20594482

  14. Hemocompatibility of Chitosan/poly(acrylic acid) Grafted Polyurethane Tubing

    PubMed Central

    Lee, Hyun-Su; Tomczyk, Nancy; Kandel, Judith; Composto, Russell J.; Eckmann, David M.

    2013-01-01

    The activation and adhesion of platelets or whole blood exposed to chitosan (CH) grafted surfaces is used to evaluate the hemocompatibility of biomaterials. The biomaterial surfaces are polyurethane (PU) tubes grafted with an inner poly(acrylic acid) (PAA) and an outer CH or quaternary ammonium modified CH (CH-Q) brush. The CH, CH-Q and PAA grafted layers were characterized by ellipsometry and fluorescence microscopy. Material wear tests demonstrate that CH (CH-Q) is stably grafted onto PU tubes upon exposure to saline solution for 7 days. Using quartz-crystal microbalances with dissipation (QCM-D), in-situ adsorption of blood plasma proteins on CH and CH-Q compared to a silicon oxide control was measured. The QCM-D results showed that the physically adsorbed plasma protein layer on CH-Q and CH surfaces is softer and more viscous than the protein layer on the SiO2 surface. The CH-Q layer thus has the weakest interaction with plasma proteins. Whole blood and platelet adhesion was reduced by ~92% on CH-Q, which showed the weakest interaction with plasma protein but more viscous adsorbed plasma protein layer, compared to SiO2. Last, to examine the biologic response of platelets and neutrophils to biomaterial surfaces, CH (CH-Q)/PAA, PAA and PU tubes were tested using a Chandler Loop apparatus as an ex vivo model and flow cytometry. The blood adhesion and biologic response results showed that CH and CH-Q reduced adhesion and activation of platelets and neutrophils and improved hemocompatibility relative to other surfaces (PU and PAA). Our studies demonstrated that the properties of physically adsorbed plasma protein layer on biomaterial surfaces correlates with blood coagulation on biomaterial surfaces. PMID:24349719

  15. Comparison of impact strength of acrylic resin reinforced with kevlar and polyethylene fibres.

    PubMed

    Kamath, G; Bhargava, K

    2002-01-01

    The present study was done to evaluate the impact strengths of heat-activated acrylic resins reinforced with Kevlar fibres, polyethylene fibres and unreinforced heat activated acrylic resin. Each of three groups had 25 specimens. Brass rods of uniform length of 40 mm and diameter of 8 mm were used to prepare the moulds. A combination of long fibres (40 mm length) and short fibres (6 mm length) were used. The total amount of fibres incorporated was limited to 2% by weight of the resin matrix. Short and long fibres of equal weight were incorporated. The short fibres were mixed with polymer and monomer and packed into the mould, while, the long axis of the specimen, perpendicular to the applied force. The specimens were then processed. Impact strength testing was done on Hounsfield's impact testing machine. Kevlar fibre reinforced heat activated acrylic resin specimens recorded higher mean impact strength of 0.8464 Joules, while polyethylene fibres reinforced heat activated acrylic resin recorded mean impact strength of 0.7596 joules. The unreinforced heat activated acrylic resin recorded mean impact strength of 0.3440 Joules.

  16. Synthesis of a novel acrylated abietic acid-g-bacterial cellulose hydrogel by gamma irradiation.

    PubMed

    Abeer, Muhammad Mustafa; Amin, Mohd Cairul Iqbal Mohd; Lazim, Azwan Mat; Pandey, Manisha; Martin, Claire

    2014-09-22

    Acrylated abietic acid (acrylated AbA) and acrylated abietic acid-grafted bacterial cellulose pH sensitive hydrogel (acrylated AbA-g-BC) were prepared by a one-pot synthesis. The successful dimerization of acrylic acid (AA) and abietic acid (AbA) and grafting of the dimer onto bacterial cellulose (BC) was confirmed by 13C solid state NMR as well as FT-IR. X-ray diffraction analysis showed characteristic peaks for AbA and BC; further, there was no effect of increasing amorphous AA content on the overall crystallinity of the hydrogel. Differential scanning calorimetry revealed a glass transition temperature of 80°C. Gel fraction and swelling studies gave insight into the features of the hydrogel, suggesting that it was suitable for future applications such as drug delivery. Scanning electron microscopy observations showed an interesting interpenetrating network within the walls of hydrogel samples with the lowest levels of AA and gamma radiation doses. Cell viability test revealed that the synthesized hydrogel is safe for future use in biomedical applications.

  17. The antimicrobial effect of benzalkonium chloride on some pathogenic microbes observed on fibers of acrylic carpet.

    PubMed

    Khajavi, Ramin; Sattari, Morteza; Ashjaran, Ali

    2007-02-15

    In the presented research, the main aim is to investigate the antibacterial effectiveness of BAC solutions on acrylic fibers used in machinery carpet. An acrylic pile carpet laid in a public place for 30 days and the existence of some microbes were investigated on it. The antimicrobial effect of different BAC solutions for identified microbes was studied in vitro. The acrylic fibers were treated with the same different solutions of BAC as before and the antibacterial effectiveness was assessed by the zone of inhibition method in different times. Two pieces of carpet untreated and treated with BAC solution sewed together and laid for one week in the public place and the amounts of bacterial growth determined by colony count method and the results compared. Finally some mechanical properties of treated acrylic fibers measured after 30 days and compared with untreated one. The results showed the presence of some pathogenic microbes on the laid carpet such as Escherichia coli and Staphylococcus aureus. The inhalation time for treated acrylic fibers improved. The amount of colony growth on treated carpet reduced considerably and besides the mechanical tests results showed no significant deterioration effect of studied properties in comparing with untreated yarn.

  18. Effect of sealant application and thermal cycling on bond strength of tissue conditioners to acrylic resin.

    PubMed

    Sampaio, Francisca Neta Cruz Soares; Pinto, José Renato Ribeiro; Turssi, Cecília Pedroso; Basting, Roberta Tarkany

    2013-01-01

    The aim of this study was to evaluate the effect of sealer application and thermal cycling on the bond strength between tissue conditioners and acrylic resin, and to observe the type of bond failure. Two hundred eighty-eight specimens (10x16x3 mm) were made of an acrylic resin (Lucitone 500, Dentsply) using a metal muffle. Specimens were divided into four groups according to the tissue conditioner (Coe-Comfort, GC or Dentusoft, Densell) used and whether or not a sealer (Eversoft Soft Liner Sealer, Myerson) was applied. Each of the four groups was subdivided into other six subgroups (n=12) to undergo thermocycling for 45, 90, 135, 180 or 210 cycles with a dwell time of 60 s, or to be left non thermocycled (control). Tensile bond strength was measured in a universal testing machine at a crosshead speed of 5 mm/min. Sealant application had no effect on the tensile bond strength of the relined acrylic resin, regardless of the tissue conditioner used (Coe-Comfort: p=0.306 and Dentusoft: p=0.1501). The number of thermal cycles had a significant effect on the tensile bond strength of the relined acrylic resin (Coe-Comfort: p=0.002 and Dentusoft: p<0.001). Both tissue conditioners presented similar bond strength to acrylic resin. For both tissue conditioners, sealer coatings had no influence on bond strength, while different numbers of thermal cycles affected that mechanical property.

  19. Radiation modification of water absorption of cassava starch by acrylic acid/acrylamide

    NASA Astrophysics Data System (ADS)

    Kiatkamjornwong, Suda; Chomsaksakul, Wararuk; Sonsuk, Manit

    2000-10-01

    Graft copolymerizations of acrylamide and/or acrylic acid onto cassava starch by a simultaneous irradiation technique using gamma-rays as the initiator were studied with regard to various parameters of importance: the monomer-to-cassava starch ratio, total dose (kGy), dose rate (kGy h -1), acrylamide-to-acrylic acid ratio, and the addition of nitric acid and maleic acid as the additives. Grafting parameters were determined in relation to the water absorption of the saponified graft copolymer. The water absorption of the saponified graft copolymer in salt and buffer solutions of different ionic strengths was also measured, from which the superabsorbent properties are found to be pH sensitive. The starch graft copolymers of acrylamide and acrylic acid give higher water absorption than the starch graft copolymers of either acrylamide or acrylic acid alone. The porosity of the saponified starch graft copolymers prepared by the acrylamide/acrylic acid ratios of 70:30 and 50:50 was much higher than the porosity of copolymers in terms of fine networks. Ionic strength and multi-oxidation states of the saline and buffer solutions markedly decreased the water absorption of the saponified cassava starch grafted superabsorbent polymers.

  20. Electrically conducting silver/guar gum/poly(acrylic acid) nanocomposite.

    PubMed

    Abdel-Halim, E S; Al-Deyab, Salem S

    2014-08-01

    This article describes the synthesis of an electrically conducting silver/guar gum/poly(acrylic acid) nanocomposite hydrogel. The synthesis process started with grafting acrylic acid monomers onto the natural polymer guar gum by the use of ammonium persulphate as a free radical initiator in acid medium. Guar gum/poly(acrylic acid) graft copolymer was separated from the polymerization medium, purified and subjected to crosslinking treatment, using alkaline epichlorohydrin as a crosslinking agent. Silver nitrate solution was added during the crosslinking treatment in varying concentrations, that the reaction conditions affect crosslinking of guar gum/poly(acrylic acid) graft copolymer to a hydrogel, as well as reduction of silver nitrate to silver nanoparticles, giving rise to the formation of silver/guar gum/poly(acrylic acid) nanocomposite. Factors affecting the grafting reaction as well as those affecting the crosslinking/reduction treatment were optimized. The so synthesized nanocomposite hydrogel samples were fully characterized, regarding their contents of silver nanoparticles and swelling ratio. The electrical conductivity of the nanocomposite hydrogel was studied and it was found to be affected by the swelling ratio of the hydrogel as well as its content of silver nanoparticles. PMID:24928058

  1. Electrically conducting silver/guar gum/poly(acrylic acid) nanocomposite.

    PubMed

    Abdel-Halim, E S; Al-Deyab, Salem S

    2014-08-01

    This article describes the synthesis of an electrically conducting silver/guar gum/poly(acrylic acid) nanocomposite hydrogel. The synthesis process started with grafting acrylic acid monomers onto the natural polymer guar gum by the use of ammonium persulphate as a free radical initiator in acid medium. Guar gum/poly(acrylic acid) graft copolymer was separated from the polymerization medium, purified and subjected to crosslinking treatment, using alkaline epichlorohydrin as a crosslinking agent. Silver nitrate solution was added during the crosslinking treatment in varying concentrations, that the reaction conditions affect crosslinking of guar gum/poly(acrylic acid) graft copolymer to a hydrogel, as well as reduction of silver nitrate to silver nanoparticles, giving rise to the formation of silver/guar gum/poly(acrylic acid) nanocomposite. Factors affecting the grafting reaction as well as those affecting the crosslinking/reduction treatment were optimized. The so synthesized nanocomposite hydrogel samples were fully characterized, regarding their contents of silver nanoparticles and swelling ratio. The electrical conductivity of the nanocomposite hydrogel was studied and it was found to be affected by the swelling ratio of the hydrogel as well as its content of silver nanoparticles.

  2. In Vitro Antifungal Evaluation of Seven Different Disinfectants on Acrylic Resins

    PubMed Central

    Yildirim-Bicer, A. Z.; Peker, I.; Akca, G.; Celik, I.

    2014-01-01

    Objective. The aim of this study was to evaluate alternative methods for the disinfection of denture-based materials. Material and Methods. Two different denture-based materials were included in the study. Before microbial test, the surface roughness of the acrylic resins was evaluated. Then, the specimens were divided into 8 experimental groups (n = 10), according to microorganism considered and disinfection methods used. The specimens were contaminated in vitro by standardized suspensions of Candida albicans ATCC#90028 and Candida albicans oral isolate. The following test agents were tested: sodium hypochlorite (NaOCl 1%), microwave (MW) energy, ultraviolet (UV) light, mouthwash containing propolis (MCP), Corega Tabs, 50% and 100% white vinegar. After the disinfection procedure, the number of remaining microbial cells was evaluated in CFU/mL. Kruskal-Wallis, ANOVA, and Dunn's test were used for multiple comparisons. Mann Whitney U test was used to compare the surface roughness. Results. Statistically significant difference (P < 0.05) was found between autopolymerised and heat-cured acrylic resins. The autopolymerised acrylic resin surfaces were rougher than surfaces of heat-cured acrylic resin. The most effective disinfection method was 100% white vinegar for tested microorganisms and both acrylic resins. Conclusion. This study showed that white vinegar 100% was the most effective method for tested microorganisms. This agent is cost-effective and easy to access and thus may be appropriate for household use. PMID:24995305

  3. Conversion of (Meth)acrylic acids to methane granular sludge: Initiation by specific anerobic microflora

    SciTech Connect

    Shtarkman, N.B.; Obraztova, A.Y.; Laurinavichyus, K.S.; Galushko, A.S.; Akimenko, V.K.

    1995-03-01

    The role of a specific anaerobic microflora in the initiation of degradation of (meth)acrylic acids to methane by granular sludge from a UASB reactor was investigated. Associations of anaerobic bacteria isolated from the anaerobic sludge, which was used for a long time for treatment of wastewater from (meth)acrylate production, were able to realize the initial stage of (meth)acrylic acid decomposition, i.e., a conversion of acrylic and methacrylic acids to propionic and isobutyric acids, respectively. When added to granules, these association played a role of an {open_quotes}initiator{close_quotes} of the degradation process, which was then continued by the granular sludge microflora utilizing propionate and isobutyrate. Some characteristics of the granules adapted to propionate or isobutyrate are presented. The rates of propionate and isobutyrate consumption by adapted granules is, respectively, 21 and 53 times higher than the values obtained for nonadapted granules. A combined use of {open_quotes}initiating{close_quotes} bacteria and adapted granules provided degradation of (meth)acrylic acids with a maximum methane yield. The possibility is discussed of employing the granules, which are adapted to short-chain fatty acids, and the {open_quotes}initiating{close_quotes} bacteria, which accomplish the initial steps of the organic material decomposition to lower fatty acids, for the conversion of various chemical compounds to methane. 10 refs., 3 figs., 2 tabs.

  4. The electrospinning of the copolymer of styrene and butyl acrylate for its application as oil absorbent.

    PubMed

    Xu, Naiku; Cao, Jipeng; Lu, Yuyao

    2016-01-01

    Electrospun polystyrene materials have been employed as oil absorbents, but they have visible drawbacks such as poor strength at low temperature and unreliable integrity because of brittleness and insufficient cohesive force among fibers. Butyl acrylate can polymerize into flexible chains, and its polymer can be used as elastomer and adhesive material. Thereby it is possible to obtain the material that has better performance in comparison with electrospun polystyrene material through the electrospinning of the copolymer of styrene and butyl acrylate. In this work, a polymer was synthesized through suspension polymerization by using styrene and butyl acrylate as comonomers. The synthesis of the copolymer of styrene and butyl acrylate was verified through dissolution and hydrolysis experimental data; as well through nuclear magnetic resonance spectrometry. The viscous flow activation energy of the solution consisting of copolymer and N, N-dimethylformamide was determined via viscosity method and then adopted to establish the entanglement characteristics of butyl acrylate's chain segments. Finally, in order to electrospin the copolymer solution into fibrous membrane, the effects of monomer feed ratio and spinning parameters were investigated. The prepared fibrous membrane was found to have a potential use as oil absorbent. PMID:27610302

  5. Catalytic production of methyl acrylates by gold-mediated cross coupling of unsaturated aldehydes with methanol

    NASA Astrophysics Data System (ADS)

    Karakalos, Stavros; Zugic, Branko; Stowers, Kara J.; Biener, Monika M.; Biener, Juergen; Friend, Cynthia M.; Madix, Robert J.

    2016-10-01

    Modern methods of esterification, one of the most important reactions in organic synthesis, are reaching their limits, as far as waste and expense are concerned. Novel chemical approaches to ester formation are therefore of importance. Here we report a simple procedure free of caustic reagents or byproducts for the facile direct oxidative methyl esterification of aldehydes over nanoporous Au catalysts. Complementary model studies on single crystal gold surfaces establish the fundamental reactions involved. We find that methanol more readily reacts with adsorbed active oxygen than do the aldehydes, but that once the aldehydes do react, they form strongly-bound acrylates that block reactive sites and decrease the yields of acrylic esters under steady flow conditions at 420 K. Significant improvements in yield can be achieved by operating at higher temperatures, which render the site-blocking acrylates unstable.

  6. New blends of ethylene-butyl acrylate copolymers with thermoplastic starch. Characterization and bacterial biodegradation.

    PubMed

    Morro, A; Catalina, F; Corrales, T; Pablos, J L; Marin, I; Abrusci, C

    2016-09-20

    Ethylene-butyl acrylate copolymer (EBA) with 13% of butyl acrylate content was used to produce blends with 10, 30 and 60% of thermoplastic starch (TPS) plasticized with glycerol. Ethylene-acrylic acid copolymer (EAA) was used as compatibilizer at 20% content with respect to EBA. The blends were characterized by X-ray diffraction, ATR-Fourier Transform Infrared Spectroscopy (ATR-FTIR), Scanning Electron Microscopy (SEM), water-Contact Angle measurements (CA), Differential Scanning Calorimetry (DSC) and Stress-strain mechanical tests. Initiated autoxidation of the polymer blends was studied by chemiluminescence (CL) confirming that the presence of the polyolefin-TPS interphase did not substantially affect the oxidative thermostability of the materials. Three bacterial species have been isolated from the blend films buried in soil and identified as Bacillus subtilis, Bacillus borstelensis and Bacillus licheniformis. Biodegradation of the blends (28days at 45°C) was evaluated by carbon dioxide measurement using the indirect impedance technique. PMID:27261731

  7. Pathogenesis of neurotoxicity of acrylates acrylonitrile and acrylamide: from cell to organism.

    PubMed

    Tarskikh, M M; Klimatskaya, L G; Kolesnikov, S I

    2013-08-01

    The incubation of 10 mM acrylamide (in vitro) with rat brain homogenate was followed by a decrease in catalase activity by 48% as soon as 5 min after addition of acrylate to the incubation medium. Activity of this enzyme remained low 30 min after the start of the experiment. Acute poisoning with this acrylate was accompanied by LPO activation in rat brain 24 h after injection. Exposure to acrylonitrile during occupational contacts with this monomer was followed by accumulation of adducts of acrylate with erythrocytic hemoglobin in human blood. In accordance with previously observed data, modern scheme of neurotropic effects of acrylonitrile and acrylamide was proposed. This scheme explained specific features of clinical syndromes induced by acute and chronic exposure to these toxic agents. PMID:24143365

  8. Acrylic bone cements: the role of nanotechnology in improving osteointegration and tunable mechanical properties.

    PubMed

    Lissarrague, María H; Fascio, Mirta L; Goyanes, Silvia; D'Accorso, Norma B

    2014-12-01

    Nanotechnology is an extremely powerful emerging technology, which is expected to have a substantial impact on biomedical technology, especially in tissue engineering and drug delivery. The use of nanocompounds and nanoparticles in the synthesis of improved bone cements to be applied in vertebroplasty/kyphoplasty and arthroplasty, is of great interest due to the increasing incidence of osteoporosis and osteoarthritis. This review reports new advances in the development of acrylic bone cements, using different radio-opalescent nanomaterials taking into consideration their influence on the mechanical behavior and biocompatibility of the resulting acrylic bone cement. Furthermore, other non-radiopaque nanoparticles capable of mechanically reinforcing the bone cement as well as induce osteointegration, are also reviewed. Additionally, nanoparticles used to improve the controlled release of antibiotics contained in acrylic bone cements are briefly described. PMID:26000369

  9. Testing and Characterization of Acrylic for the Daya Bay Reactor Neutrino Experiment

    NASA Astrophysics Data System (ADS)

    Krohn, Michael; Littlejohn, Bryce; Heeger, Karsten

    2011-10-01

    The Daya Bay reactor antineutrino experiment will determine the last unknown neutrino mixing angle T13 with a sensitivity of.01 or better. The measurement of T13 is important for theoretical model building and for possible searches of CP violation in the neutrino sector. Poly(methyl methacrylate), otherwise known as acrylic, is an important component for the construction of the target vessels in the antineutrino detectors and we have performed multiple tests that determined its unique properties. My project has been to understand the properties of acrylic in order to minimize systematic errors and test mechanical and materials compatibility issues in the Daya Bay reactor antineutrino experiment. These tests address both the mechanical and technical issues of the detector as well as the systematic affects introduced by the acrylic.

  10. Radiation synthesis of superabsorbent poly(acrylic acid)-carrageenan hydrogels

    NASA Astrophysics Data System (ADS)

    Francis, Sanju; Kumar, Manmohan; Varshney, Lalit

    2004-04-01

    A series of superabsorbent hydrogels were prepared from carrageenan and partially neutralized acrylic acid by gamma irradiation at room temperature. The gel fraction, swelling kinetics and the equilibrium degree of swelling (EDS) of the hydrogels were studied. It was found that the incorporation of even 1% carrageenan (sodium salt) increases the EDS of the hydrogels from ˜320 to ˜800 g/g. Thermal analysis were carried out to determine the amount of free water and bound water in the hydrogels. Under optimum conditions, poly(acrylic acid)-carrageenan hydrogels with high gel fraction (˜80%) and very high EDS (˜800 g/g) were prepared gamma radiolytically from aqueous solution containing 15% partially neutralized acrylic acid and 1-5% carrageenan. The hydrogels were also found to be sensitive to the pH and the ionic strength of the medium.

  11. [MORPHOLOGICAL FEATURES OF RAT MUCOUS MEMBRANE OF THE TONGUE EARLY AFFECTED BY ACRYLIC RESIN MONOMER].

    PubMed

    Davydenko, V; Nidzelskiy, M; Starchenko, I; Davydenko, A; Kuznetsov, V

    2016-03-01

    Base materials, made on the basis of various derivatives of acrylic and methacrylic acids, have been widely used in prosthetic dentistry. Free monomer, affecting the tissues of prosthetic bed and the whole body, is always found in dentures. Therefore, study of the effect of acrylic resins' monomer on mucous membrane of the tongue is crucial. Rat tongue is very similar to human tongue, and this fact has become the basis for selecting these animals to be involved into the experiment. The paper presents the findings related to the effect of "Ftoraks" base acrylic resin monomer on the state of rat mucous membrane of the tongue and its regeneration. The microscopy has found that the greatest changes in the mucous membrane of the tongue occur on day 3 and 7 day after applying the monomer and are of erosive and inflammatory nature. Regeneration of tongue epithelium slows down. PMID:27119844

  12. Processing factors affecting the clarity of a rapid-curing clear acrylic resin.

    PubMed

    Keng, S B; Cruickshanks-Boyd, D W; Davies, E H

    1979-10-01

    The difficulty in repeatedly producing unblemished, clear acrylic resin in the dental laboratory has hindered its wider use, despite its many advantages over coloured material. Recently, rapid-cure dental acrylics have been introduced, which are available in both clear and coloured forms. This investigation examined various factors which may influence the production of unblemished, rapid-curing, clear acrylic resin. Utilizing a quantitative assessment of clarity, the most important factor influencing the clarity of the resin is shown to be the choice of separating medium. Tin-foil produces extremely high clarity, but alginate mould separator causes surface blanching. However, this surface blanching can be removed by polishing. Porosity, caused by too rapid curing, and stone model dryness are of only secondary importance. Possible water contamination of the monomer liquid due to accidental exposure only affects clarity at very high levels of contamination.

  13. Applications of Blue Light-curing Acrylic Resin to Forensic Sample Preparation and Microtomy.

    PubMed

    Groves, Ethan; Palenik, Christopher S

    2016-03-01

    This study discusses the results of an evaluation of a one-part blue light-curing acrylic resin for embedding trace evidence prior to the preparation of thin sections with a microtome. Through a comparison to several epoxy resins, the physical properties relevant to both trace evidence examination and analytical microscopy in general, including as viscosity, clarity, color, hardness, and cure speed, were explored. Finally, thin sections from paint samples embedded in this acrylic resin were evaluated to determine if, through smearing or impregnation, the resin contributed to the infrared spectra. The results of this study show that blue light-curing acrylic resins provide the desired properties of an embedding medium, generate high-quality thin sections, and can significantly simplify the preparation of paint chips, fibers and a multitude of other types of microscopic samples in the forensic trace evidence laboratory.

  14. Applications of Blue Light-curing Acrylic Resin to Forensic Sample Preparation and Microtomy.

    PubMed

    Groves, Ethan; Palenik, Christopher S

    2016-03-01

    This study discusses the results of an evaluation of a one-part blue light-curing acrylic resin for embedding trace evidence prior to the preparation of thin sections with a microtome. Through a comparison to several epoxy resins, the physical properties relevant to both trace evidence examination and analytical microscopy in general, including as viscosity, clarity, color, hardness, and cure speed, were explored. Finally, thin sections from paint samples embedded in this acrylic resin were evaluated to determine if, through smearing or impregnation, the resin contributed to the infrared spectra. The results of this study show that blue light-curing acrylic resins provide the desired properties of an embedding medium, generate high-quality thin sections, and can significantly simplify the preparation of paint chips, fibers and a multitude of other types of microscopic samples in the forensic trace evidence laboratory. PMID:27404623

  15. Optical contouring of an acrylic surface for non-intrusive diagnostics in pipe-flow investigations

    NASA Astrophysics Data System (ADS)

    de Witt, Benjamin J.; Coronado-Diaz, Haydee; Hugo, Ronald J.

    2008-07-01

    In this work, an acrylic surface was optically contoured to correct for the optical distortion caused by a transparent pipe wall. This method can be applied to non-invasive viewing/imaging techniques for fluid flow experiments. Software tools were developed to aid in the design of an optically contoured acrylic test section for pipe-flow experiments. Numerical models were computed for a standard acrylic pipe, inner diameter 57.15 mm, with water enclosed. An optical contour prototype was machined on a 5-axis CNC machine, and polished with 1-15 μm diamond paste, alleviating any surface imperfections without significantly altering the contoured surface. Experiments were then performed to measure the emerging optical wavefront and was found to emerge planar when utilizing the optical contour. It was determined that the wavefront was corrected to within ten wavelengths of a Helium-Neon (He-Ne) laser beam.

  16. Synthesis of acrylic and allylic bifunctional cross-linking monomers derived from PET waste

    NASA Astrophysics Data System (ADS)

    Cruz-Aguilar, A.; Herrera-González, A. M.; Vázquez-García, R. A.; Navarro-Rodríguez, D.; Coreño, J.

    2013-06-01

    An acrylic and two novel allylic monomers synthesized from bis (hydroxyethyl) terephthalate, BHET, are reported. This was obtained by glycolysis of post-consumer PET with boiling ethylene glycol. The bifunctional monomer bis(2-(acryloyloxy)ethyl) terephthalate was obtained from acryloyl chloride, while the allylic monomers 2-(((allyloxi)carbonyl)oxy) ethyl (2-hydroxyethyl) terephthalate and bis(2-(((allyloxi)carbonyl)oxy)ethyl) terephthalate, from allyl chloroformate. Cross-linking was studied in bulk polymerization using two different thermal initiators. Monomers were analyzed by means of 1H NMR and the cross-linked polymers by infrared spectroscopy. Gel content higher than 90% was obtained for the acrylic monomer. In the case of the mixture of the allylic monomers, the cross-linked polymer was 80 % using BPO initiator, being this mixture 24 times less reactive than the acrylic monomer.

  17. Nitrile Hydratase and Amidase from Rhodococcus rhodochrous Hydrolyze Acrylic Fibers and Granular Polyacrylonitriles

    PubMed Central

    Tauber, M. M.; Cavaco-Paulo, A.; Robra, K.-H.; Gübitz, G. M.

    2000-01-01

    Rhodococcus rhodochrous NCIMB 11216 produced nitrile hydratase (320 nkat mg of protein−1) and amidase activity (38.4 nkat mg of protein−1) when grown on a medium containing propionitrile. These enzymes were able to hydrolyze nitrile groups of both granular polyacrylonitriles (PAN) and acrylic fibers. Nitrile groups of PAN40 (molecular mass, 40 kDa) and PAN190 (molecular mass, 190 kDa) were converted into the corresponding carbonic acids to 1.8 and 1.0%, respectively. In contrast, surfacial nitrile groups of acrylic fibers were only converted to the corresponding amides. X-ray photoelectron spectroscopy analysis showed that 16% of the surfacial nitrile groups were hydrolyzed by the R. rhodochrous enzymes. Due to the enzymatic modification, the acrylic fibers became more hydrophilic and thus, adsorption of dyes was enhanced. This was indicated by a 15% increase in the staining level (K/S value) for C.I. Basic Blue 9. PMID:10742253

  18. 2-[6,8-Dibromo-3-(4-hydroxy­cyclo­hexyl)-1,2,3,4-tetra­hydro­quinazolin-2-yl]-6-methoxy­phenol

    PubMed Central

    Wang, Zhi-Gang; Wang, Rong; Zhang, Yi; Zhi, Feng; Yang, Yi-Lin

    2009-01-01

    The title compound, C21H24Br2N2O3, was synthesized by the condensation reaction of 3-methoxy­salicylaldehyde with 4-(2-amino-3,5-dibromo­benzyl­amino)cyclo­hexa­nol in a methanol solution. The dihedral angle between the two benzene rings is 76.4 (3)°. The cyclo­hexyl ring adopts a chair configuration. There is an intra­molecular O—H⋯N hydrogen bond which affects the solid state conformation of the mol­ecule. The crystal structure is stabilized by inter­molecular O—H⋯O hydrogen bonds, forming chains running along the b axis. PMID:21582209

  19. Real-time monitoring of the penetration of amphiphilic acrylate copolymer in leather using a fluorescent copolymer as tracer.

    PubMed

    Du, Jin-Xia; Shi, Lu; Peng, Bi-Yu

    2015-12-01

    A fluorescent tracer, poly (acrylic-co-stearyl acrylate-co-3-acryloyl fluorescein) [poly (AA-co-SA-co-Ac-Flu)], used for real-time monitoring the penetration of amphiphilic acrylate copolymer, poly (acrylic-co-stearyl acrylate) [poly (AA-co-SA)], in leather was synthesized by radical polymerization of acrylic, stearyl acrylate and fluorescent monomer, 3-acryloyl fluorescein (Ac-Flu). The structure, molecular weight, introduced fluorescent group content and fluorescent characteristics of the fluorescent tracer and target copolymer, amphiphilic acrylate copolymer, were also characterized. The results show that the tracer presents the similar structural characteristics to the target and enough fluorescence intensity with 1.68 wt % of the fluorescent monomer introduced amount. The vertical section of the leather treated with the target copolymer mixing with 7% of the tracer exhibits evident fluorescence, and the change of fluorescence intensity along with the vertical section with treating time increasing can reflect the penetration depth of the target copolymer. The introduction of the fluorescent group in polymer structure through copolymerization with a limited amount of fluorescent monomer, Ac-Flu, is an effective way to make a tracer to monitor the penetration of the target in leather, which provides a new thought for the penetration research of syntans such as vinyl copolymer materials in leather manufacture.

  20. Molecular dissection of bacterial acrylate catabolism--unexpected links with dimethylsulfoniopropionate catabolism and dimethyl sulfide production.

    PubMed

    Todd, Jonathan D; Curson, Andrew R J; Nikolaidou-Katsaraidou, Nefeli; Brearley, Charles A; Watmough, Nicholas J; Chan, Yohan; Page, Philip C B; Sun, Lei; Johnston, Andrew W B

    2010-02-01

    A bacterium in the genus Halomonas that grew on dimethylsulfoniopropionate (DMSP) or acrylate as sole carbon sources and that liberated the climate-changing gas dimethyl sulfide in media containing DMSP was obtained from the phylloplane of the macroalga Ulva. We identified a cluster that contains genes specifically involved in DMSP catabolism (dddD, dddT) or in degrading acrylate (acuN, acuK) or that are required to break down both substrates (dddC, dddA). Using NMR and HPLC analyses to trace 13C- or 14C-labelled acrylate and DMSP in strains of Escherichia coli with various combinations of cloned ddd and/or acu genes, we deduced that DMSP is imported by the BCCT-type transporter DddT, then converted by DddD to 3-OH-propionate (3HP), liberating dimethyl sulfide in the process. As DddD is a predicted acyl CoA transferase, there may be an earlier, unidentified catabolite of DMSP. Acrylate is also converted to 3HP, via a CoA transferase (AcuN) and a hydratase (AcuK). The 3HP is predicted to be catabolized by an alcohol dehydrogenase, DddA, to malonate semialdehyde, thence by an aldehyde dehydrogenase, DddC, to acyl CoA plus CO2. The regulation of the ddd and acu genes is unusual, as a catabolite, 3HP, was a co-inducer of their transcription. This first description of genes involved in acrylate catabolism in any organism shows that the relationship between the catabolic pathways of acrylate and DMSP differs from that which had been suggested in other bacteria.